Powered by Deep Web Technologies
Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

AOI [3] High-Temperature Nano-Derived Micro-H2 and - H2S Sensors  

SciTech Connect (OSTI)

The emissions from coal-fired power plants remain a significant concern for air quality. This environmental challenge must be overcome by controlling the emission of sulfur dioxide (SO2) and hydrogen sulfide (H2S) throughout the entire coal combustion process. One of the processes which could specifically benefit from robust, low cost, and high temperature compatible gas sensors is the coal gasification process which converts coal and/or biomass into syngas. Hydrogen (H2), carbon monoxide (CO) and sulfur compounds make up 33%, 43% and 2% of syngas, respectively. Therefore, development of a high temperature (>500°C) chemical sensor for in-situ monitoring of H2, H2S and SO2 levels during coal gasification is strongly desired. The selective detection of SO2/H2S in the presence of H2, is a formidable task for a sensor designer. In order to ensure effective operation of these chemical sensors, the sensor system must inexpensively function within harsh temperature and chemical environment. Currently available sensing approaches, which are based on gas chromatography, electrochemistry, and IR-spectroscopy, do not satisfy the required cost and performance targets. This work focused on the development microsensors that can be applied to this application. In order to develop the high- temperature compatible microsensor, this work addressed various issues related to sensor stability, selectivity, and miniaturization. In the research project entitled “High-Temperature Nano-Derived Micro-H2 and -H2S Sensors”, the team worked to develop micro-scale, chemical sensors and sensor arrays composed of nano-derived, metal-oxide composite materials to detect gases like H2, SO2, and H2S within high-temperature environments (>500?C). The research was completed in collaboration with NexTech Materials, Ltd. (Lewis Center, Ohio). NexTech assisted in the testing of the sensors in syngas with contaminate levels of H2S. The idea of including nanomaterials as the sensing material within resistive-type chemical sensor platforms was to increase the sensitivity (as shown for room temperature applications). Unfortunately, nanomaterials are not stable at high temperatures due to sintering and coarsening processes that are driven by their high surface to volume ratio. Therefore, new hydrogen and sulfur selective nanomaterial systems with high selectivity and stability properties in the proposed harsh environment were investigated. Different nano-morphologies of zirconate, molybdate, and tungstate compounds were investigated. The fabrication of the microsensors consisted of the deposition of the selective nanomaterial systems over metal based interconnects on an inert substrate. This work utilized the chemi-resistive (resistive- type) microsensor architecture where the chemically and structurally stable, high temperature compatible electrodes were sputtered onto a ceramic substrate. The nanomaterial sensing systems were deposited over the electrodes using a lost mold method patterned by conventional optical lithography. The microsensor configuration with optimized nanomaterial system was tested and compared to a millimeter-size sensor e outcomes of this research will contribute to the economical application of sensor arrays for simultaneous sensing of H2, H2S, and SO2.

Perepezko, John; Lu-Steffes, Otto

2014-08-31T23:59:59.000Z

2

Microsoft PowerPoint - High-Temperature Nano-Derived_Sabolsky  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Temperature Nano-Derived Temperature Nano-Derived Micro-H 2 and -H 2 S Sensors Engin Ciftyurek (Ph.D. Candidate) Christina Wildfire (Graduated Student, Ph.D.) Edward M. Sabolsky (PI) Energy Materials Program Department of Mechanical and Aerospace Engineering West Virginia University Annual DOE-NETL University Coal Research Project Review June 11-13, 2013 Objectives * Develop micro-scale, chemical sensors composed of nano-derived, metal-oxide materials which display stable performance within high-temperature environments (>500C). * Short term- Develop high-temperature H 2 and H 2 S sensor using low cost, easily reproducible methods with 3D porous nanomaterials. * Long term - Develop high-temperature micro-sensor arrays to detect gases such as NO

3

High-Temperature Nano-Derived Micro-Hydrogen Sulfide Sensors  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Temperature Nano-Derived Micro- Temperature Nano-Derived Micro- Hydrogen and -Hydrogen Sulfide Sensors Background The Department of Energy (DOE) National Energy Technology Laboratory (NETL) seeks applications for the University Coal Research (UCR) Program to further develop the understanding of coal utilization. Since the program's inception in 1979, its primary objectives have been to (1) improve our understanding of the chemical and physical processes involved in the conversion and utilization of coal in an environmentally

4

crosscutting | netl.doe.gov  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Central Florida Graphene-Based Composite Sensors for Energy Applications Charter D. Stinespring, West Virginia University High-Temperature Nano-Derived Micro-H2 and H2S Sensors...

5

High Temperatures & Electricity Demand  

E-Print Network [OSTI]

High Temperatures & Electricity Demand An Assessment of Supply Adequacy in California Trends.......................................................................................................1 HIGH TEMPERATURES AND ELECTRICITY DEMAND.....................................................................................................................7 SECTION I: HIGH TEMPERATURES AND ELECTRICITY DEMAND ..........................9 BACKGROUND

6

High temperature pressure gauge  

DOE Patents [OSTI]

A high temperature pressure gauge comprising a pressure gauge positioned in fluid communication with one end of a conduit which has a diaphragm mounted in its other end. The conduit is filled with a low melting metal alloy above the diaphragm for a portion of its length with a high temperature fluid being positioned in the remaining length of the conduit and in the pressure gauge.

Echtler, J. Paul (Pittsburgh, PA); Scandrol, Roy O. (Library, PA)

1981-01-01T23:59:59.000Z

7

High Temperature Superconductors  

Science Journals Connector (OSTI)

Abstract A brief review of the phenomenology of superconductivity, the distinction between type I and type II superconductors, and the application of type II superconductors is followed by a history of the theory of conventional superconductivity. Unconventional high-temperature superconductivity in the copper oxides is reviewed as a phenomenon occurring in narrow two-dimensional bands where the time for an electron transfer between like atoms is comparable to the period of an optical-mode lattice vibration. A family of iron pnictides containing layers of iron atoms may not require an alternative explanation of its high-temperature superconductivity.

J.B. Goodenough

2013-01-01T23:59:59.000Z

8

Chemistry at High Temperatures  

Science Journals Connector (OSTI)

...347 the condensed phase. Both cases are...show the opposite behavior. These predictions...vapors. Condensed phase B203 B + B203 02...complex silicates and hydrates in high-temperature...characterized by phase diagrams (derived...doubt that thou-sands of new chemical materials...

John L. Margrave

1962-02-02T23:59:59.000Z

9

High Temperature Membrane Working Group  

Broader source: Energy.gov [DOE]

The High Temperature Membrane Working Group consists of government, industry, and university researchers interested in developing high temperature membranes for fuel cells.

10

High temperature probe  

DOE Patents [OSTI]

A high temperature probe for sampling, for example, smokestack fumes, and is able to withstand temperatures of 3000.degree. F. The probe is constructed so as to prevent leakage via the seal by placing the seal inside the water jacket whereby the seal is not exposed to high temperature, which destroys the seal. The sample inlet of the probe is also provided with cooling fins about the area of the seal to provide additional cooling to prevent the seal from being destroyed. Also, a heated jacket is provided for maintaining the temperature of the gas being tested as it passes through the probe. The probe includes pressure sensing means for determining the flow velocity of an efficient being sampled. In addition, thermocouples are located in various places on the probe to monitor the temperature of the gas passing there through.

Swan, Raymond A. (Fremont, CA)

1994-01-01T23:59:59.000Z

11

High Temperature Membrane Working Group  

Broader source: Energy.gov [DOE]

This presentation provides an overview of the High Temperature Membrane Working Group Meeting in May 2007.

12

High temperature detonator  

DOE Patents [OSTI]

A detonator assembly is provided which is usable at high temperatures about 300.degree. C. A detonator body is provided with an internal volume defining an anvil surface. A first acceptor explosive is disposed on the anvil surface. A donor assembly having an ignition element, an explosive material, and a flying plate, are placed in the body effective to accelerate the flying plate to impact the first acceptor explosive on the anvil for detonating the first acceptor explosive. A second acceptor explosive is eccentrically located in detonation relationship with the first acceptor explosive to thereafter effect detonation of a main charge.

Johnson, James O. (Los Alamos, NM); Dinegar, Robert H. (Los Alamos, NM)

1988-01-01T23:59:59.000Z

13

High temperature thermometric phosphors  

DOE Patents [OSTI]

A high temperature phosphor consists essentially of a material having the general formula LuPO.sub.4 :Dy.sub.(x),Eu.sub.y) wherein: 0.1 wt %.ltoreq.x.ltoreq.20 wt % and 0.1 wt %.ltoreq.y.ltoreq.20 wt %. The high temperature phosphor is in contact with an article whose temperature is to be determined. The article having the phosphor in contact with it is placed in the environment for which the temperature of the article is to be determined. The phosphor is excited by a laser causing the phosphor to fluoresce. The emission from the phosphor is optically focused into a beam-splitting mirror which separates the emission into two separate emissions, the emission caused by the dysprosium dopant and the emission caused by the europium dopent. The separated emissions are optically filtered and the intensities of the emission are detected and measured. The ratio of the intensity of each emission is determined and the temperature of the article is calculated from the ratio of the intensities of the separate emissions.

Allison, Stephen W. (Knoxville, TN); Cates, Michael R. (Oak Ridge, TN); Boatner, Lynn A. (Oak Ridge, TN); Gillies, George T. (Earlysville, VA)

1999-03-23T23:59:59.000Z

14

High-Temperature Water Splitting  

Broader source: Energy.gov [DOE]

High-temperature water splitting (a "thermochemical" process) is a long-term technology in the early stages of development.

15

High-temperature Pump Monitoring - High-temperature ESP Monitoring...  

Broader source: Energy.gov (indexed) [DOE]

Report Detecting Fractures Using Technology at High Temperatures and Depths - Geothermal Ultrasonic Fracture Imager (GUFI); 2010 Geothermal Technology Program Peer Review Report...

16

High Temperature Processing Symposium 2014  

E-Print Network [OSTI]

} High temperature recycling operations } Materials sustainability } New furnace technology (including solar) We look forward to seeing you in February 2014. Dr M Akbar Rhamdhani (Chairman HTPS 2014) Prof

Liley, David

17

High Temperature | Open Energy Information  

Open Energy Info (EERE)

Temperature Temperature Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Print PDF Sanyal Temperature Classification: High Temperature Dictionary.png High Temperature: No definition has been provided for this term. Add a Definition Sanyal Temp Classification This temperature scheme was developed by Sanyal in 2005 at the request of DOE and GEA, as reported in Classification of Geothermal Systems: A Possible Scheme. Extremely Low Temperature Very Low Temperature Low Temperature Moderate Temperature High Temperature Ultra High Temperature Steam Field Reservoir fluid between 230°C and 300°C is considered by Sanyal to be "high temperature." "Above a temperature level of 230°C, the reservoir would be expected to become two-phase at some point during exploitation. The next higher

18

Philosophy 26 High Temperature Superconductivity  

E-Print Network [OSTI]

is the ratio of voltage to current. The resistance of a material tells us how a low resistance, and they are therefore good conductors; other materials, likePhilosophy 26 High Temperature Superconductivity By Ohm's Law, resistance

Callender, Craig

19

High Temperature Optical Gas Sensing  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Optical Gas Sensing Optical Gas Sensing Opportunity Research is active on optical sensors integrated with advanced sensing materials for high temperature embedded gas sensing applications. Patent applications have been filed for two inventions in this area and several other methods are currently under development. These technologies are available for licensing and/or further collaborative research from the U.S. Department of Energy's National Energy Technology Laboratory (NETL). Organizations or individuals with capabilities in optical sensor packaging for harsh environment and high temperature applications are encouraged to contact NETL to explore potential collaborative opportunities. Overview Contact NETL Technology Transfer Group techtransfer@netl.doe.gov

20

High temperature superconductor current leads  

DOE Patents [OSTI]

An electrical lead is disclosed having one end for connection to an apparatus in a cryogenic environment and the other end for connection to an apparatus outside the cryogenic environment. The electrical lead includes a high temperature superconductor wire and an electrically conductive material distributed therein, where the conductive material is present at the one end of the lead at a concentration in the range of from 0 to about 3% by volume, and at the other end of the lead at a concentration of less than about 20% by volume. Various embodiments are shown for groups of high temperature superconductor wires and sheaths. 9 figs.

Hull, J.R.; Poeppel, R.B.

1995-06-20T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

High temperature lightweight foamed cements  

DOE Patents [OSTI]

Cement slurries are disclosed which are suitable for use in geothermal wells since they can withstand high temperatures and high pressures. The formulation consists of cement, silica flour, water, a retarder, a foaming agent, a foam stabilizer, and a reinforcing agent. A process for producing these cements is also disclosed. 3 figs.

Sugama, Toshifumi.

1989-10-03T23:59:59.000Z

22

High temperature turbine engine structure  

DOE Patents [OSTI]

A high temperature turbine engine includes a rotor portion having axially stacked adjacent ceramic rotor parts. A ceramic/ceramic joint structure transmits torque between the rotor parts while maintaining coaxial alignment and axially spaced mutually parallel relation thereof despite thermal and centrifugal cycling.

Boyd, Gary L. (Tempe, AZ)

1991-01-01T23:59:59.000Z

23

Acid Doped Membranes for High Temperature PEMFC  

Broader source: Energy.gov [DOE]

Presentation on Acid Doped Membranes for High Temperature PEMFC to the High Temperature Membrane Working Group, May 25, 2004 in Philadelphia, PA.

24

Experiment Hazard Class 3 - High Temperatures  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Operation * APS Base Low Temperatures * Cryogenic Systems High Temperatures * Electric Furnace * Optical Furnace * Other High Temperature Lasers * Laser, Class 2 * Laser,...

25

High temperature turbine engine structure  

DOE Patents [OSTI]

A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

Carruthers, William D. (Mesa, AZ); Boyd, Gary L. (Tempe, AZ)

1994-01-01T23:59:59.000Z

26

High temperature turbine engine structure  

DOE Patents [OSTI]

A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

Carruthers, William D. (Mesa, AZ); Boyd, Gary L. (Tempe, AZ)

1993-01-01T23:59:59.000Z

27

High temperature turbine engine structure  

DOE Patents [OSTI]

A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

Carruthers, William D. (Mesa, AZ); Boyd, Gary L. (Tempe, AZ)

1992-01-01T23:59:59.000Z

28

Joint Institute for High Temperatures  

National Nuclear Security Administration (NNSA)

Joint Institute for High Temperatures of Russian Academy of Sciences Moscow Institute of Physics and Technology Extended title Extended title Excited state of warm dense matter or Exotic state of warm dense matter or Novel form of warm dense matter or New form of plasma Three sources of generation similarity: solid state density, two temperatures: electron temperature about tens eV, cold ions keep original crystallographic positions, but electron band structure and phonon dispersion are changed, transient but steady (quasi-stationary for a short time) state of non-equilibrium, uniform plasmas (no reference to non-ideality, both strongly and weakly coupled plasmas can be formed) spectral line spectra are emitted by ion cores embedded in plasma environment which influences the spectra strongly,

29

High Temperature Mechanical Properties as Design Parameters  

Science Journals Connector (OSTI)

...corrosion resistance or high proof strength...development of more efficient power plant, process...Figure 2 shows a high temperature bolt...S.O.) of a Boiler Code (I968...power plant for high temperature pipework, boiler headers, valve...

1976-01-01T23:59:59.000Z

30

High-temperature thermocouples and related methods  

DOE Patents [OSTI]

A high-temperature thermocouple and methods for fabricating a thermocouple capable of long-term operation in high-temperature, hostile environments without significant signal degradation or shortened thermocouple lifetime due to heat induced brittleness.

Rempe, Joy L. (Idaho Falls, ID); Knudson, Darrell L. (Firth, ID); Condie, Keith G. (Idaho Falls, ID); Wilkins, S. Curt (Idaho Falls, ID)

2011-01-18T23:59:59.000Z

31

Materials Characterization Capabilities at the High Temperature...  

Broader source: Energy.gov (indexed) [DOE]

Characterization Capabilities at the High Temperature Materials Laboratory: Focus on Carbon Fiber and Composites Materials Characterization Capabilities at the High...

32

Reciprocity theorem in high-temperature superconductors  

E-Print Network [OSTI]

This article is devoted to the problem of the validity of the reciprocity theorem in high-temperature

Ivan Jane?ek

2002-01-01T23:59:59.000Z

33

Scaling in high-temperature superconductors by  

E-Print Network [OSTI]

A Hartree approximation is used to study the interplay of two kinds of scaling which arise in high-temperature

Ian D Lawrie

1994-01-01T23:59:59.000Z

34

Agenda: High Temperature Membrane Working Group Meeting  

Broader source: Energy.gov [DOE]

Agenda for the High Temperature Membrane Working Group (HTMWG) meeting on May 18, 2009, in Arlington, Virginia

35

High Temperature Superconducting Underground Cable  

SciTech Connect (OSTI)

The purpose of this Project was to design, build, install and demonstrate the technical feasibility of an underground high temperature superconducting (HTS) power cable installed between two utility substations. In the first phase two HTS cables, 320 m and 30 m in length, were constructed using 1st generation BSCCO wire. The two 34.5 kV, 800 Arms, 48 MVA sections were connected together using a superconducting joint in an underground vault. In the second phase the 30 m BSCCO cable was replaced by one constructed with 2nd generation YBCO wire. 2nd generation wire is needed for commercialization because of inherent cost and performance benefits. Primary objectives of the Project were to build and operate an HTS cable system which demonstrates significant progress towards commercial progress and addresses real world utility concerns such as installation, maintenance, reliability and compatibility with the existing grid. Four key technical areas addressed were the HTS cable and terminations (where the cable connects to the grid), cryogenic refrigeration system, underground cable-to-cable joint (needed for replacement of cable sections) and cost-effective 2nd generation HTS wire. This was the world’s first installation and operation of an HTS cable underground, between two utility substations as well as the first to demonstrate a cable-to-cable joint, remote monitoring system and 2nd generation HTS.

Farrell, Roger, A.

2010-02-28T23:59:59.000Z

36

Ultra High Temperature | Open Energy Information  

Open Energy Info (EERE)

Ultra High Temperature Ultra High Temperature Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Print PDF Sanyal Temperature Classification: Ultra High Temperature Dictionary.png Ultra High Temperature: No definition has been provided for this term. Add a Definition Sanyal Temp Classification This temperature scheme was developed by Sanyal in 2005 at the request of DOE and GEA, as reported in Classification of Geothermal Systems: A Possible Scheme. Extremely Low Temperature Very Low Temperature Low Temperature Moderate Temperature High Temperature Ultra High Temperature Steam Field Reservoir fluid greater than 300°C is considered by Sanyal to be "ultra high temperature". "Such reservoirs are characterized by rapid development of steam saturation in the reservoir and steam fraction in the mobile fluid phase upon

37

Electrochemical investigations of various high-temperature superconductor phases  

Science Journals Connector (OSTI)

Electrochemical investigations of various high-temperature superconductor phases ... Electrochemistry of High-Temperature Superconductors ...

David R. Riley; A. Manthiram; John T. McDevitt

1992-11-01T23:59:59.000Z

38

Nanostructured High Temperature Bulk Thermoelectric Energy Conversion...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Efficient Automotive Waste Heat Recovery Multi-physics modeling of thermoelectric generators for waste heat recovery applications Nanostructured High-Temperature Bulk...

39

High Temperature Thermoelectric Materials Characterization for...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

2009 -- Washington D.C. lmp06wang.pdf More Documents & Publications High-Temperature Thermoelectric Materials Characterization for Automotive Waste Heat Recovery: Success...

40

Materials Characterization Capabilities at the High Temperature...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Laboratory and HTML User Program Success Stories Materials Characterization Capabilities at the High Temperature Materials Laboratory: Focus on Carbon Fiber and Composites...

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

High Temperature Materials Laboratory (HTML) - PSD Directorate  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

filler A National Resource for Collaborative Materials Research The High Temperature Materials Laboratory (HTML) User Program is on hiatus due to federal budget reductions....

42

High Temperature Solar Splitting of Methane  

E-Print Network [OSTI]

-term commercialization opportunities #12;Why Use Solar Energy?Why Use Solar Energy? · High concentrations possible (>1000High Temperature Solar Splitting of Methane to Hydrogen and Carbon High Temperature Solar Splitting and worldwide) ­ Sufficient to power the world (if we choose to) · Advantages tradeoff against collection area

43

QED3 Theory of High Temperature Superconductors  

E-Print Network [OSTI]

QED3 Theory of High Temperature Superconductors Zlatko TesanoviŽc The Johns Hopkins University is The Problem in high Tc superconductors? · Superconducting state appears dx2-y2 "BCS-like". Low energy: · Today, everything seems to be a high temperature superconduc- tor (cuprates, C60's, MgB2

Tesanovic, Zlatko

44

Hole doping in high temperature superconductors using the XANES technique  

E-Print Network [OSTI]

Hole doping in high temperature superconductors using the1994 Thallium-Based High Temperature Superconductors ed A M1994 Thallium-Based High Temperature Superconductors ed A M

Hamdan, Nasser

2012-01-01T23:59:59.000Z

45

Symposium on high temperature and materials chemistry  

SciTech Connect (OSTI)

This volume contains the written proceedings of the Symposium on High Temperature and Materials Chemistry held in Berkeley, California on October 24--25, 1989. The Symposium was sponsored by the Materials and Chemical Sciences Division of Lawrence Berkeley Laboratory and by the College of Chemistry of the University of California at Berkeley to discuss directions, trends, and accomplishments in the field of high temperature and materials chemistry. Its purpose was to provide a snapshot of high temperature and materials chemistry and, in so doing, to define status and directions.

Not Available

1989-10-01T23:59:59.000Z

46

An internal winding high temperature heater  

Science Journals Connector (OSTI)

An internal winding high temperature heater ... General principles are outlined for the construction of compact heaters that are suitable for heating small containers or reaction vessels at constant temperature and up to about 1000 C. ...

A. J. Delbouille; E. G. Derouane

1973-01-01T23:59:59.000Z

47

Noise Absorbing High-Temperature Insulation  

Science Journals Connector (OSTI)

Until recently simple heat shields on the engine, in the engine space or on the subframe of a vehicle had given protection against radiant heat from hot components. Today, complex high-temperature insulation syst...

Peter Cappellucci

2013-07-01T23:59:59.000Z

48

Thermodynamics of high-temperature nuclear fuel  

Science Journals Connector (OSTI)

A method for performing a thermodynamic analysis of the high-temperature nuclear fuel using the ASTA computer program is substantiated. Calculations of the chemical composition and pressure of the gas phase of...

I. A. Belov; A. S. Ivanov

49

High Temperature Cements | Open Energy Information  

Open Energy Info (EERE)

High Temperature Cements High Temperature Cements Jump to: navigation, search Geothermal ARRA Funded Projects for High Temperature Cements Loading map... {"format":"googlemaps3","type":"ROADMAP","types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"limit":200,"offset":0,"link":"all","sort":[""],"order":[],"headers":"show","mainlabel":"","intro":"","outro":"","searchlabel":"\u2026 further results","default":"","geoservice":"google","zoom":false,"width":"600px","height":"350px","centre":false,"layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","icon":"","visitedicon":"","forceshow":true,"showtitle":true,"hidenamespace":false,"template":false,"title":"","label":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"locations":[{"text":"

50

High Temperature Membrane & Advanced Cathode Catalyst Development  

SciTech Connect (OSTI)

Current project consisted of three main phases and eighteen milestones. Short description of each phase is given below. Table 1 lists program milestones. Phase 1--High Temperature Membrane and Advanced Catalyst Development. New polymers and advanced cathode catalysts were synthesized. The membranes and the catalysts were characterized and compared against specifications that are based on DOE program requirements. The best-in-class membranes and catalysts were downselected for phase 2. Phase 2--Catalyst Coated Membrane (CCM) Fabrication and Testing. Laboratory scale catalyst coated membranes (CCMs) were fabricated and tested using the down-selected membranes and catalysts. The catalysts and high temperature membrane CCMs were tested and optimized. Phase 3--Multi-cell stack fabrication. Full-size CCMs with the down-selected and optimized high temperature membrane and catalyst were fabricated. The catalyst membrane assemblies were tested in full size cells and multi-cell stack.

Protsailo, Lesia

2006-04-20T23:59:59.000Z

51

High temperature crystalline superconductors from crystallized glasses  

DOE Patents [OSTI]

A method of preparing a high temperature superconductor from an amorphous phase. The method involves preparing a starting material of a composition of Bi.sub.2 Sr.sub.2 Ca.sub.3 Cu.sub.4 Ox or Bi.sub.2 Sr.sub.2 Ca.sub.4 Cu.sub.5 Ox, forming an amorphous phase of the composition and heat treating the amorphous phase for particular time and temperature ranges to achieve a single phase high temperature superconductor.

Shi, Donglu (Downers Grove, IL)

1992-01-01T23:59:59.000Z

52

Frustrated phase separation and high temperature superconductivity  

SciTech Connect (OSTI)

A dilute system of neutral holes in an antiferromagnet separates into a hole-rich and a hole-poor phase. The phase separation is frustrated by long-range Coulomb interactions but, provided the dielectric constant is sufficiently large, there remain large-amplitude low-energy fluctuations in the hole density at intermediate length scales. The extensive experimental evidence showing that this behavior giver, a reasonable picture of high temperature superconductors is surveyed. Further, it is shown that the scattering of mobile holes from the local density fluctuations may account for the anomalous normal-state properties of high temperature superconductors and also provide the mechanism of pairing.

Emery, V.J. [Brookhaven National Lab., Upton, NY (United States); Kivelson, S.A. [California Univ., Los Angeles, CA (United States). Dept. of Physics

1992-09-01T23:59:59.000Z

53

Frustrated phase separation and high temperature superconductivity  

SciTech Connect (OSTI)

A dilute system of neutral holes in an antiferromagnet separates into a hole-rich and a hole-poor phase. The phase separation is frustrated by long-range Coulomb interactions but, provided the dielectric constant is sufficiently large, there remain large-amplitude low-energy fluctuations in the hole density at intermediate length scales. The extensive experimental evidence showing that this behavior giver, a reasonable picture of high temperature superconductors is surveyed. Further, it is shown that the scattering of mobile holes from the local density fluctuations may account for the anomalous normal-state properties of high temperature superconductors and also provide the mechanism of pairing.

Emery, V.J. (Brookhaven National Lab., Upton, NY (United States)); Kivelson, S.A. (California Univ., Los Angeles, CA (United States). Dept. of Physics)

1992-01-01T23:59:59.000Z

54

Potential applications of high temperature helium  

SciTech Connect (OSTI)

This paper discusses the DOE MHTGR-SC program`s recent activity to improve the economics of the MHTGR without sacrificing safety performance and two potential applications of high temperature helium, the MHTGR gas turbine plant and a process heat application for methanol production from coal.

Schleicher, R.W. Jr.; Kennedy, A.J.

1992-09-01T23:59:59.000Z

55

Potential applications of high temperature helium  

SciTech Connect (OSTI)

This paper discusses the DOE MHTGR-SC program's recent activity to improve the economics of the MHTGR without sacrificing safety performance and two potential applications of high temperature helium, the MHTGR gas turbine plant and a process heat application for methanol production from coal.

Schleicher, R.W. Jr.; Kennedy, A.J.

1992-09-01T23:59:59.000Z

56

High temperature storage loop : final design report.  

SciTech Connect (OSTI)

A three year plan for thermal energy storage (TES) research was created at Sandia National Laboratories in the spring of 2012. This plan included a strategic goal of providing test capability for Sandia and for the nation in which to evaluate high temperature storage (>650%C2%B0C) technology. The plan was to scope, design, and build a flow loop that would be compatible with a multitude of high temperature heat transfer/storage fluids. The High Temperature Storage Loop (HTSL) would be reconfigurable so that it was useful for not only storage testing, but also for high temperature receiver testing and high efficiency power cycle testing as well. In that way, HTSL was part of a much larger strategy for Sandia to provide a research and testing platform that would be integral for the evaluation of individual technologies funded under the SunShot program. DOE's SunShot program seeks to reduce the price of solar technologies to 6/kWhr to be cost competitive with carbon-based fuels. The HTSL project sought to provide evaluation capability for these SunShot supported technologies. This report includes the scoping, design, and budgetary costing aspects of this effort

Gill, David Dennis; Kolb, William J.

2013-07-01T23:59:59.000Z

57

High Temperature, Permanent Magnet Biased Magnetic Bearings  

E-Print Network [OSTI]

performance, high speed and high temperature applications like space vehicles, jet engines and deep sea equipment. The bearing system had a target design to carry a load equal to 500 lb-f (2225N). Another objective was to design and build a test rig fixture...

Gandhi, Varun R.

2010-07-14T23:59:59.000Z

58

The High-Temperature Oxidation of Propane  

Science Journals Connector (OSTI)

...research-article The High-Temperature Oxidation of Propane J. W. Falconer J. H. Knox Above 400 degrees C propane is oxidized by a two-stage degenerately...of propylene becomes important. While propane still in the main reacts to form propylene...

1959-01-01T23:59:59.000Z

59

Metallic Hydrogen: A High-Temperature Superconductor?  

Science Journals Connector (OSTI)

Application of the BCS theory to the proposed metallic modification of hydrogen suggests that it will be a high-temperature superconductor. This prediction has interesting astrophysical consequences, as well as implications for the possible development of a superconductor for use at elevated temperatures.

N. W. Ashcroft

1968-12-23T23:59:59.000Z

60

Vehicle Technologies Office: ORNL's High Temperature Materials Laboratory  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

ORNL's High Temperature ORNL's High Temperature Materials Laboratory Assists NASCAR Teams to someone by E-mail Share Vehicle Technologies Office: ORNL's High Temperature Materials Laboratory Assists NASCAR Teams on Facebook Tweet about Vehicle Technologies Office: ORNL's High Temperature Materials Laboratory Assists NASCAR Teams on Twitter Bookmark Vehicle Technologies Office: ORNL's High Temperature Materials Laboratory Assists NASCAR Teams on Google Bookmark Vehicle Technologies Office: ORNL's High Temperature Materials Laboratory Assists NASCAR Teams on Delicious Rank Vehicle Technologies Office: ORNL's High Temperature Materials Laboratory Assists NASCAR Teams on Digg Find More places to share Vehicle Technologies Office: ORNL's High Temperature Materials Laboratory Assists NASCAR Teams on AddThis.com...

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Vehicle Technologies Office Merit Review 2014: High-Temperature...  

Broader source: Energy.gov (indexed) [DOE]

High-Temperature Air-Cooled Power Electronics Thermal Design Vehicle Technologies Office Merit Review 2014: High-Temperature Air-Cooled Power Electronics Thermal Design...

62

High Temperature Polymer Membrane Development at Argonne National...  

Broader source: Energy.gov (indexed) [DOE]

Polymer Membrane Development at Argonne National Laboratory High Temperature Polymer Membrane Development at Argonne National Laboratory Summary of ANL's high temperature polymer...

63

High Temperature Fuel Cells in the European Union  

Broader source: Energy.gov [DOE]

Presentation on High Temperature Fuel Cells in the European Union to the High Temperature Membrane Working Group, May 25, 2004 in Philadelphia, PA.

64

Low and high Temperature Dual Thermoelectric Generation Waste...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Low and high Temperature Dual Thermoelectric Generation Waste Heat Recovery System for Light-Duty Vehicles Low and high Temperature Dual Thermoelectric Generation Waste Heat...

65

High temperature membranes for DMFC (and PEFC) applications  

Broader source: Energy.gov [DOE]

Presentation on High temperature membranes for DMFCs (and PEFCs) to the High Temperature Membrane Working Group, May 25, 2004 in Philadelphia, PA.

66

Development of Advanced High Temperature Fuel Cell Membranes  

Broader source: Energy.gov [DOE]

Presentation on Development of Advanced High Temperature Fuel Cell Membranes to the High Temperature Membrane Working Group Meeting held in Arlington, Virginia, May 26,2005.

67

Development of a 100-Watt High Temperature Thermoelectric Generator...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Generator Development of a 100-Watt High Temperature Thermoelectric Generator Test results for low and high temperature thermoelectric generators (TEG) those for a...

68

A Discussion of Conductivity Testing in High Temperature Membranes...  

Broader source: Energy.gov (indexed) [DOE]

A Discussion of Conductivity Testing in High Temperature Membranes (lessons learned in assessing transport) A Discussion of Conductivity Testing in High Temperature Membranes...

69

High Temperature Polymer Membrane Development at Argonne National Laboratory  

Broader source: Energy.gov [DOE]

Summary of ANL’s high temperature polymer membrane work presented to the High Temperature Membrane Working Group Meeting, Orlando FL, October 17, 2003

70

Nanostructured High-Temperature Bulk Thermoelectric Energy Conversion...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Nanostructured High-Temperature Bulk Thermoelectric Energy Conversion for Efficient Automotive Waste Heat Recovery Nanostructured High-Temperature Bulk Thermoelectric Energy...

71

Microchannel High-Temperature Recuperator for Fuel Cell Systems...  

Office of Environmental Management (EM)

Microchannel High-Temperature Recuperator for Fuel Cell Systems - Fact Sheet, 2014 Microchannel High-Temperature Recuperator for Fuel Cell Systems - Fact Sheet, 2014 FuelCell...

72

Polyelectrolyte Materials for High Temperature Fuel Cells | Department...  

Broader source: Energy.gov (indexed) [DOE]

Polyelectrolyte Materials for High Temperature Fuel Cells Polyelectrolyte Materials for High Temperature Fuel Cells This presentation, which focuses on polyelectrolyte materials...

73

High Reliability, High TemperatureThermoelectric Power Generation...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Reliability, High TemperatureThermoelectric Power Generation Materials and Technologies High Reliability, High TemperatureThermoelectric Power Generation Materials and Technologies...

74

Improved Martensitic Steel for High Temperature Applications  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Improved Martensitic Steel Improved Martensitic Steel for High Temperature Applications Opportunity Research is active on the patented technology, titled "Heat-Treated 9 Cr-1 Mo Steel for High Temperature Application." This technology is available for licensing and/or further collaborative research from the U.S. Department of Energy's National Energy Technology Laboratory (NETL). Overview The operating efficiency of coal-fired power plants is directly related to combustion system temperature and pressure. Incorporation of ultra- supercritical (USC) steam conditions into new or existing power plants can achieve increased efficiency and reduce coal consumption, while reducing carbon dioxide emissions as well as other pollutants. Traditionally used materials do not possess the optimal characteristics for operation

75

Manufacturing Barriers to High Temperature PEM Commercialization  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

9/2011 9/2011 1 BASF Fuel Cell, Inc. Manufacturing Barriers to high temperature PEM commercialization 39 Veronica Ave Somerset , NJ 08873 Tel : (732) 545-5100 9/9/2011 2 Background on BASF Fuel Cell ïź BASF Fuel Cell was established in 2007, formerly PEMEAS Fuel Cells (including E-TEK) ïź Product line is high temperature MEAs (Celtec Âź P made from PBI-phosphoric acid) ïź Dedicated a new advanced pilot manufacturing facility in Somerset NJ May 2009. Ribbon-cutting hosted by Dr. Kreimeyer (BASF BoD, right) and attended by various US pubic officials including former NJ Governor Jon Corzine (left) 9/9/2011 3 Multi-layer product of membrane (polybenzimidazole and phosphoric acid), gas diffusion material and catalysts Unique characteristics: ïź High operating temperature

76

Thermal fuse for high-temperature batteries  

DOE Patents [OSTI]

A thermal fuse, preferably for a high-temperature battery, comprising leads and a body therebetween having a melting point between approximately 400.degree. C. and 500.degree. C. The body is preferably an alloy of Ag--Mg, Ag--Sb, Al--Ge, Au--In, Bi--Te, Cd--Sb, Cu--Mg, In--Sb, Mg--Pb, Pb--Pd, Sb--Zn, Sn--Te, or Mg--Al.

Jungst, Rudolph G. (Albuquerque, NM); Armijo, James R. (Albuquerque, NM); Frear, Darrel R. (Austin, TX)

2000-01-01T23:59:59.000Z

77

Magnetism in Iron at High Temperatures  

Science Journals Connector (OSTI)

Magnetism in iron at high temperature is investigated by calculating the total electronic band-structure energy for four types of spin arrangements. A slow smooth spatial variation of spin direction costs relatively little energy and the atomic moment m is reduced only ? 10%. More rapid variations have considerably higher energy, which may explain the high degree of short-range order and small ?m observed at T?TC. Other aspects are also discussed.

M. V. You; V. Heine; A. J. Holden; P. J. Lin-Chung

1980-05-12T23:59:59.000Z

78

Establishment of Harrop, High-Temperature Viscometer  

SciTech Connect (OSTI)

This report explains how the Harrop, High-Temperature Viscometer was installed, calibrated, and operated. This report includes assembly and alignment of the furnace, viscometer, and spindle, and explains the operation of the Brookfield Viscometer, the Harrop furnace, and the UDC furnace controller. Calibration data and the development of the spindle constant from NIST standard reference glasses is presented. A simple operational procedure is included.

Schumacher, R.F.

1999-11-05T23:59:59.000Z

79

Charged Vortices in High Temperature Superconductors  

Science Journals Connector (OSTI)

It is argued that in the mixed state of a type II superconductor, because of the difference of the chemical potential in a superconducting versus normal state, the vortex cores may become charged. The extra electron density is estimated. The extra charge contributes to the dynamics of the vortices; in particular, it can explain in certain cases the change of the sign of the Hall coefficient below Tc frequently observed in the high temperature superconductors.

D. I. Khomskii and A. Freimuth

1995-08-14T23:59:59.000Z

80

High Temperature Materials for Aerospace Applications  

E-Print Network [OSTI]

below 430 ?C for exposure times up to 20 minutes. Transition-metal carbides were initially synthesized by carbothermal reduction of transition-metal halides and polymer precursor mixtures, at temperatures that range from 900 to 1500 ?C in an argon... ........................................ 20 2.3 Present/Future Aerospace Applications ......................................... 24 2.4 Ultra-High Temperature Materials ................................................. 27 2.4.1 Transition-Metal Carbides...

Adamczak, Andrea Diane

2011-08-08T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Fermi liquid theory for high temperature superconductors  

SciTech Connect (OSTI)

In this article the Fermi liquid theory of metals is discussed starting from Luttinger's theorem. The content of Luttinger's Theorem and its implications for microscopic theories of high temperature superconductors are discussed. A simple quasi-2d Fermi liquid theory is introduced and some of its properties are calculated. It is argued that a number of experiments on YBa/sub 2/Cu/sub 3/O/sub 6+x/, x > 0.5, strongly suggest the existence of a Fermi surface and thereby a Fermi liquid normal state. 25 refs., 1 fig.

Bedell, K.S.

1988-01-01T23:59:59.000Z

82

3 - High temperature superconductor (HTS) cables  

Science Journals Connector (OSTI)

Abstract: Many superconductor applications such as rotating machinery, transformers and magnets with low inductance require high current cables with low AC losses. This chapter gives an overview on cabling techniques for the high temperature superconductors (HTS) BSCCO (2212), BSCCO (2223) and (RE)BCO. A short review is given of the basic properties of HTS wires and tapes and the basic requirements of HTS cables for different applications. Cabling concepts for the different HTS materials are presented, and current performance and AC loss behaviour are discussed. After a short description of remaining challenges and future trends, cabling techniques are summarized.

S.I. Schlachter; W. Goldacker

2012-01-01T23:59:59.000Z

83

5 - High temperature superconductor (HTS) magnets  

Science Journals Connector (OSTI)

Abstract: At the time of writing, high temperature superconducting magnets have not fulfilled their early promise, mainly because of the difficulties in getting these reactive and brittle ceramics into wire form and, consequently, their expense. However, for some niche applications, HTS magnets have been developed. In this chapter, the author outlines his experience of building four such systems after introductory discussions about superconducting magnets in general and design considerations. The recent commercial availability of so-called second-generation (2G) coated conductors opens up a more promising scenario, provided the cost can come down. This scenario is discussed and some conclusions are drawn.

H. Jones

2012-01-01T23:59:59.000Z

84

Boson linewidth in high-temperature superconductors  

Science Journals Connector (OSTI)

We have considered boson exchange models of high-temperature superconductors which use Eliashberg theory and in which the bare bosons have sharp spectral features. In particular, we have calculated the boson linewidth due to the interaction with the charge carriers. We find for a recent model of Arnold, Mueller, and Swihart that the width of the 10-meV peak in their ?2F is consistent with a broadened boson peak. However, for a weak-coupling model with the boson peak in the eV range, the interaction causes a broadening in the boson peak that is comparable to or larger than the energy of the peak.

James C. Swihart; William H. Butler; Fred M. Mueller; Gerald B. Arnold

1992-09-01T23:59:59.000Z

85

Applications of bulk high-temperature superconductors  

SciTech Connect (OSTI)

The development of high-temperature superconductors (HTSs) can be broadly generalized into thin-film electronics, wire applications, and bulk applications. We consider bulk HTSs to include sintered or crystallized forms that do not take the geometry of filaments or tapes, and we discuss major applications for these materials. For the most part applications may be realized with the HTSs cooled to 77 K, and the properties of the bulk HTSs are often already sufficient for commercial use. A non-exhaustive list of applications for bulk HTSs includes trapped field magnets, hysteresis motors, magnetic shielding, current leads, and magnetic bearings. These applications are briefly discussed in this paper.

Hull, J.R.

1995-06-01T23:59:59.000Z

86

High Temperature Materials Laboratory third annual report  

SciTech Connect (OSTI)

The High Temperature Materials Laboratory has completed its third year of operation as a designated DOE User Facility at the Oak Ridge National Laboratory. Growth of the user program is evidenced by the number of outside institutions who have executed user agreements since the facility began operation in 1987. A total of 88 nonproprietary agreements (40 university and 48 industry) and 20 proprietary agreements (1 university, 19 industry) are now in effect. Sixty-eight nonproprietary research proposals (39 from university, 28 from industry, and 1 other government facility) and 8 proprietary proposals were considered during this reporting period. Research projects active in FY 1990 are summarized.

Tennery, V.J.; Foust, F.M.

1990-12-01T23:59:59.000Z

87

High temperature lined conduits, elbows and tees  

DOE Patents [OSTI]

A high temperature lined conduit comprising, a liner, a flexible insulating refractory blanket around and in contact with the liner, a pipe member around the blanket and spaced therefrom, and castable rigid refractory material between the pipe member and the blanket. Anchors are connected to the inside diameter of the pipe and extend into the castable material. The liner includes male and female slip joint ends for permitting thermal expansion of the liner with respect to the castable material and the pipe member. Elbows and tees of the lined conduit comprise an elbow liner wrapped with insulating refractory blanket material around which is disposed a spaced elbow pipe member with castable refractory material between the blanket material and the elbow pipe member. A reinforcing band is connected to the elbow liner at an intermediate location thereon from which extend a plurality of hollow tubes or pins which extend into the castable material to anchor the lined elbow and permit thermal expansion. A method of fabricating the high temperature lined conduit, elbows and tees is also disclosed which utilizes a polyethylene layer over the refractory blanket after it has been compressed to maintain the refractory blanket in a compressed condition until the castable material is in place. Hot gases are then directed through the interior of the liner for evaporating the polyethylene and setting the castable material which permits the compressed blanket to come into close contact with the castable material.

De Feo, Angelo (Passaic, NJ); Drewniany, Edward (Bergen, NJ)

1982-01-01T23:59:59.000Z

88

High temperature intermetallic binders for HVOF carbides  

SciTech Connect (OSTI)

Gas turbines technology has a long history of employing the desirable high temperature physical attributes of ceramic-metallic (cermet) materials. The most commonly used coatings incorporate combinations of WC-Co and Cr{sub 3}C{sub 2}-NiCr, which have also been successfully utilized in other non-turbine coating applications. Increased turbine operating temperatures and other high temperature service conditions have made apparent the attractive notion of increasing the temperature capability and corrosion resistance of these coatings. In this study the intermetallic binder NiAl has been used to replace the cobalt and NiCr constituents of conventional WC and Cr{sub 3}C{sub 2} cermet powders. The composite carbide thermal spray powders were fabricated for use in the HVOF coating process. The structure of HVOF deposited NiAl-carbide coatings are compared directly to the more familiar WC-Co and Cr{sub 3}C{sub 2}-NiCr coatings using X-ray diffraction, back-scattered electron imaging (BEI) and electron dispersive spectroscopy (EDS). Hardness variations with temperature are reported and compared between the NiAl and Co/NiCr binders.

Shaw, K.G. [Xform, Inc., Cohoes, NY (United States); Gruninger, M.F.; Jarosinski, W.J. [Praxair Specialty Powders, Indianapolis, IN (United States)

1994-12-31T23:59:59.000Z

89

Flux noise in high-temperature superconductors  

Science Journals Connector (OSTI)

Spontaneously created vortex-antivortex pairs are the predominant source of flux noise in high-temperature superconductors. In principle, flux noise measurements allow to check theoretical predictions for both the distribution of vortex-pair sizes and for the vortex diffusivity. In this paper the flux-noise power spectrum is calculated for the highly anisotropic high-temperature superconductor Bi2Sr2CaCu2O8+?, both for bulk crystals and for ultrathin films. The spectrum is basically given by the Fourier transform of the temporal magnetic-field correlation function. We start from a Berezinskii-Kosterlitz-Thouless-type theory and incorporate vortex diffusion, intrapair vortex interaction, and annihilation of pairs by means of a Fokker-Planck equation to determine the noise spectrum below and above the superconducting transition temperature. We find white noise at low frequencies ? and a spectrum proportional to 1/?3/2 at high frequencies. The crossover frequency between these regimes strongly depends on temperature. The results are compared with earlier results of computer simulations.

Carsten Timm

1997-02-01T23:59:59.000Z

90

High temperature electrochemical corrosion rate probes  

SciTech Connect (OSTI)

Corrosion occurs in the high temperature sections of energy production plants due to a number of factors: ash deposition, coal composition, thermal gradients, and low NOx conditions, among others. Electrochemical corrosion rate (ECR) probes have been shown to operate in high temperature gaseous environments that are similar to those found in fossil fuel combustors. ECR probes are rarely used in energy production plants at the present time, but if they were more fully understood, corrosion could become a process variable at the control of plant operators. Research is being conducted to understand the nature of these probes. Factors being considered are values selected for the Stern-Geary constant, the effect of internal corrosion, and the presence of conductive corrosion scales and ash deposits. The nature of ECR probes will be explored in a number of different atmospheres and with different electrolytes (ash and corrosion product). Corrosion rates measured using an electrochemical multi-technique capabilities instrument will be compared to those measured using the linear polarization resistance (LPR) technique. In future experiments, electrochemical corrosion rates will be compared to penetration corrosion rates determined using optical profilometry measurements.

Bullard, Sophie J.; Covino, Bernard S., Jr.; Holcomb, Gordon R.; Ziomek-Moroz, M.

2005-09-01T23:59:59.000Z

91

High Temperature Materials Laboratory (HTML) - PSD Directorate  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

filler A National Resource for Collaborative Materials Research The High Temperature Materials Laboratory (HTML) User Program is on hiatus due to federal budget reductions. However, research projects at the HTML still may be conducted on a cost-recovery basis through the Work for Others (WFO) Program or under a Cooperative R&D Agreement (CRADA). Dr. Edgar Lara-Curzio, HTML Director Tel: 865.574.1749 Fax: 865.574.4913 laracurzioe@ornl.gov Christine Goudy, Administrative Specialist Tel: 865.574.8295 Fax: 865.574.4913 goudyc@ornl.gov Oak Ridge National Laboratory [MST Home] [ORNL Home] [Site Index] [Search][Disclaimer] [Webmaster] Oak Ridge National Laboratory is a national multi-program research and development facility managed by UT-Battelle, LLC for the U.S. Department of Energy

92

Superconductivity Program Overview High-Temperature Superconductivity  

Broader source: Energy.gov (indexed) [DOE]

SuperconducTiviTy program haS Three FocuS areaS: SuperconducTiviTy program haS Three FocuS areaS: SuperconducTiviTy applicaTionS Developing HTS-based electric power equipment such as transmission and distribution cables and fault current limiters Second-generaTion Wire developmenT Developing high-performance, low-cost, second- generation HTS wire at long lengths STraTegic reSearch Supporting fundamental research activities to better understand relationships between the microstructure of HTS materials and their ability to carry large electric currents over long lengths Superconductivity Program Overview High-Temperature Superconductivity for Electric Systems Office of Electricity Delivery and Energy Reliability www.oe.energy.gov Office of Electricity Delivery and Energy Reliability, OE-1 U.S. Department of Energy - 1000 Independence Avenue, SW - Washington, DC 20585

93

Multilayer ultra-high-temperature ceramic coatings  

DOE Patents [OSTI]

A coated carbon-carbon composite material with multiple ceramic layers to provide oxidation protection from ultra-high-temperatures, where if the carbon-carbon composite material is uninhibited with B.sub.4C particles, then the first layer on the composite material is selected from ZrB.sub.2 and HfB.sub.2, onto which is coated a layer of SiC coated and if the carbon-carbon composite material is inhibited with B.sub.4C particles, then protection can be achieved with a layer of SiC and a layer of either ZrB.sub.2 and HfB.sub.2 in any order.

Loehman, Ronald E. (Albuquerque, NM); Corral, Erica L. (Tucson, AZ)

2012-03-20T23:59:59.000Z

94

Compliant high temperature seals for dissimilar materials  

DOE Patents [OSTI]

A high temperature, gas-tight seal is formed by utilizing one or more compliant metallic toroidal ring sealing elements, where the applied pressure serves to activate the seal, thus improving the quality of the seal. The compliant nature of the sealing element compensates for differences in thermal expansion between the materials to be sealed, and is particularly useful in sealing a metallic member and a ceramic tube art elevated temperatures. The performance of the seal may be improved by coating the sealing element with a soft or flowable coating such as silver or gold and/or by backing the sealing element with a bed of fine powder. The material of the sealing element is chosen such that the element responds to stress elastically, even at elevated temperatures, permitting the seal to operate through multiple thermal cycles.

Rynders, Steven Walton (Fogelsville, PA); Minford, Eric (Laurys Station, PA); Tressler, Richard Ernest (Boalsburg, PA); Taylor, Dale M. (Salt Lake City, UT)

2001-01-01T23:59:59.000Z

95

Turbine vane with high temperature capable skins  

DOE Patents [OSTI]

A turbine vane assembly includes an airfoil extending between an inner shroud and an outer shroud. The airfoil can include a substructure having an outer peripheral surface. At least a portion of the outer peripheral surface is covered by an external skin. The external skin can be made of a high temperature capable material, such as oxide dispersion strengthened alloys, intermetallic alloys, ceramic matrix composites or refractory alloys. The external skin can be formed, and the airfoil can be subsequently bi-cast around or onto the skin. The skin and the substructure can be attached by a plurality of attachment members extending between the skin and the substructure. The skin can be spaced from the outer peripheral surface of the substructure such that a cavity is formed therebetween. Coolant can be supplied to the cavity. Skins can also be applied to the gas path faces of the inner and outer shrouds.

Morrison, Jay A. (Oviedo, FL)

2012-07-10T23:59:59.000Z

96

Diamond switches for high temperature electronics  

SciTech Connect (OSTI)

Diamond switches are well suited for use in high temperature electronics. Laboratory feasibility of diamond switching at 1 kV and 18 A was demonstrated. DC blocking voltages up to 1 kV were demonstrated. A 50 {Omega} load line was switched using a diamond switch, with switch on-state resistivity {approx}7 {Omega}-cm. An electron beam, {approx}150 keV energy, {approx}2 {mu}s full width at half maximum was used to control the 5 mm x 5 mm x 100 {mu}m thick diamond switch. The conduction current temporal history mimics that of the electron beam. These data were taken at room temperature.

Prasad, R.R.; Rondeau, G.; Qi, Niansheng [Alameda Applied Sciences Corp., San Leandro, CA (United States)] [and others

1996-04-25T23:59:59.000Z

97

High temperature low friction surface coating  

DOE Patents [OSTI]

A high temperature, low friction, flexible coating for metal surfaces which are subject to rubbing contact includes a mixture of three parts graphite and one part cadmium oxide, ball milled in water for four hours, then mixed with thirty percent by weight of sodium silicate in water solution and a few drops of wetting agent. The mixture is sprayed 12-15 microns thick onto an electro-etched metal surface and air dried for thirty minutes, then baked for two hours at 65.degree. C. to remove the water and wetting agent, and baked for an additional eight hours at about 150.degree. C. to produce the optimum bond with the metal surface. The coating is afterwards burnished to a thickness of about 7-10 microns.

Bhushan, Bharat (Watervliet, NY)

1980-01-01T23:59:59.000Z

98

NETL Publications: 2013 UNIVERSITY COAL RESEARCH/HISTORICALLY BLACK  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

2013 UNIVERSITY COAL RESEARCH/HISTORICALLY BLACK COLLEGES 2013 UNIVERSITY COAL RESEARCH/HISTORICALLY BLACK COLLEGES AND UNIVERSITIES AND OTHER MINORITY INSTITUTIONS CONTRACTORS REVIEW MEETING The Wyndham Grand, Pittsburgh Tuesday, June 11, 2013 Registration Opening Remarks Robert Romanosky, Technology Manager, Crosscutting Research SENSORS & CONTROL TECHNOLOGIES Moderator: Steven Markovich, HBCU Program Coordinator, Federal Project Manager, Fuels Division U.S. Department of Energy, National Energy Technology Laboratory High-Temperature Nano-Derived Micro-H2 and H2S Sensors [PDF-11.43MB] Edward Sabolsky, West Virginia University Development of High Temperature/High Sensitivity Novel Chemical Resistive Sensor [PDF-14.09MB]

99

Fuel Cell Technologies Office: 2009 High Temperature Membrane Working Group  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

9 High Temperature 9 High Temperature Membrane Working Group Meeting Archives to someone by E-mail Share Fuel Cell Technologies Office: 2009 High Temperature Membrane Working Group Meeting Archives on Facebook Tweet about Fuel Cell Technologies Office: 2009 High Temperature Membrane Working Group Meeting Archives on Twitter Bookmark Fuel Cell Technologies Office: 2009 High Temperature Membrane Working Group Meeting Archives on Google Bookmark Fuel Cell Technologies Office: 2009 High Temperature Membrane Working Group Meeting Archives on Delicious Rank Fuel Cell Technologies Office: 2009 High Temperature Membrane Working Group Meeting Archives on Digg Find More places to share Fuel Cell Technologies Office: 2009 High Temperature Membrane Working Group Meeting Archives on AddThis.com...

100

High-Temperature Solar Selective Coating Development for Power...  

Broader source: Energy.gov (indexed) [DOE]

High-Temperature Solar Selective Coating Development for Power Tower Receivers - FY13 Q2 High-Temperature Solar Selective Coating Development for Power Tower Receivers - FY13 Q2...

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Development of a 100-Watt High Temperature Thermoelectric Generator  

Broader source: Energy.gov [DOE]

Test results for low and high temperature thermoelectric generators (TEG) those for a 530-watt BiTe TEG; design and construction of a 100-watt high temperature TEG currently in fabrication.

102

Corrosion Studies in High-Temperature Molten Salt Systems for...  

Broader source: Energy.gov (indexed) [DOE]

Corrosion Studies in High-Temperature Molten Salt Systems for CSP Applications - FY13 Q1 Corrosion Studies in High-Temperature Molten Salt Systems for CSP Applications - FY13 Q1...

103

Correlated electrons in high-temperature superconductors Elbio Dagotto  

E-Print Network [OSTI]

Correlated electrons in high-temperature superconductors Elbio Dagotto Department of Physics Theoretical ideas and experimental results concerning high-temperature superconductors are reviewed. Special, National High Magnetic Field Laboratory, and MAR TECH, Florida State University, Tallahassee, Florida 32308

Wu, Zhigang

104

Motor Using High Temperature Superconductor as a Rotor  

Science Journals Connector (OSTI)

It is found that a high temperature superconductor rotates in the rotating magnetic field at ... authors and a small motor is made using high temperature superconductor as a rotor. This motor rotates at...

Makoto Takenaka; Masaharu Minami; Kazuo Morimoto

1994-01-01T23:59:59.000Z

105

Phenotyping of High Temperature Susceptibility in Garden Roses (Rosa xhybrida)  

E-Print Network [OSTI]

cultivars. Adaptation to high temperature stress is viewed as high priority in breeding programs of all major crops. High temperature stress negatively affects garden rose performance and the quality of flowers produced. The work described...

Greyvenstein, Ockert Frederick

2013-12-10T23:59:59.000Z

106

Sandia National Laboratories: High-Pressure and High-Temperature...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

ClimateECClimateCarbon CaptureHigh-Pressure and High-Temperature Neutron Reflectometry Cell for Solid-Fluid Interface Studies High-Pressure and High-Temperature Neutron...

107

High Temperature Integrated Thermoelectric Ststem and Materials  

SciTech Connect (OSTI)

The final goal of this project is to produce, by the end of Phase II, an all ceramic high temperature thermoelectric module. Such a module design integrates oxide ceramic n-type, oxide ceramic p-type materials as thermoelectric legs and oxide ceramic conductive material as metalizing connection between n-type and p-type legs. The benefits of this all ceramic module are that it can function at higher temperatures (> 700 C), it is mechanically and functionally more reliable and it can be scaled up to production at lower cost. With this all ceramic module, millions of dollars in savings or in new opportunities recovering waste heat from high temperature processes could be made available. A very attractive application will be to convert exhaust heat from a vehicle to reusable electric energy by a thermoelectric generator (TEG). Phase I activities were focused on evaluating potential n-type and p-type oxide compositions as the thermoelectric legs. More than 40 oxide ceramic powder compositions were made and studied in the laboratory. The compositions were divided into 6 groups representing different material systems. Basic ceramic properties and thermoelectric properties of discs sintered from these powders were measured. Powders with different particles sizes were made to evaluate the effects of particle size reduction on thermoelectric properties. Several powders were submitted to a leading thermoelectric company for complete thermoelectric evaluation. Initial evaluation showed that when samples were sintered by conventional method, they had reasonable values of Seebeck coefficient but very low values of electrical conductivity. Therefore, their power factors (PF) and figure of merits (ZT) were too low to be useful for high temperature thermoelectric applications. An unconventional sintering method, Spark Plasma Sintering (SPS) was determined to produce better thermoelectric properties. Particle size reduction of powders also was found to have some positive benefits. Two composition systems, specifically 1.0 SrO - 0.8 x 1.03 TiO2 - 0.2 x 1.03 NbO2.5 and 0.97 TiO2 - 0.03 NbO2.5, have been identified as good base line compositions for n-type thermoelectric compositions in future module design. Tests of these materials at an outside company were promising using that company's processing and material expertise. There was no unique p-type thermoelectric compositions identified in phase I work other than several current cobaltite materials. Ca3Co4O9 will be the primary p-type material for the future module design until alternative materials are developed. BaTiO3 and rare earth titanate based dielectric compositions show both p-type and n-type behavior even though their electrical conductivities were very low. Further research and development of these materials for thermoelectric applications is planned in the future. A preliminary modeling and optimization of a thermoelectric generator (TEG) that uses the n-type 1.0 SrO - 1.03 x 0.8 TiO2 - 1.03 x 0.2 NbO2.5 was performed. Future work will combine development of ceramic powders and manufacturing expertise at TAM, development of SPS at TAM or a partner organization, and thermoelectric material/module testing, modeling, optimization, production at several partner organizations.

Mike S. H. Chu

2011-06-06T23:59:59.000Z

108

Hydrogen Production from Nuclear Energy via High Temperature Electrolysis  

SciTech Connect (OSTI)

This paper presents the technical case for high-temperature nuclear hydrogen production. A general thermodynamic analysis of hydrogen production based on high-temperature thermal water splitting processes is presented. Specific details of hydrogen production based on high-temperature electrolysis are also provided, including results of recent experiments performed at the Idaho National Laboratory. Based on these results, high-temperature electrolysis appears to be a promising technology for efficient large-scale hydrogen production.

James E. O'Brien; Carl M. Stoots; J. Stephen Herring; Grant L. Hawkes

2006-04-01T23:59:59.000Z

109

Agenda for the High Temperature Membrane Working Group Meeting  

Broader source: Energy.gov [DOE]

This agenda provides information about the Agenda for the High Temperature Membrane Working Group Meeting on September 14, 2006.

110

High Temperature Membrane Working Group Meeting, May 14, 2007  

Broader source: Energy.gov [DOE]

This agenda provides information about the High Temperature Membrane Working Group Meeting on May 14, 2007 in Arlington, Va.

111

Nanostructured High-Temperature Bulk Thermoelectric Energy Conversion...  

Broader source: Energy.gov (indexed) [DOE]

More Documents & Publications Nanostructured High-Temperature Bulk Thermoelectric Energy Conversion for Efficient Automotive Waste Heat Recovery Vehicle Technologies Office...

112

Application of high temperature superconductors for fusion  

Science Journals Connector (OSTI)

The use of High Temperature Superconductor (HTS) materials in future fusion machines can increase the efficiency drastically. For ITER, W7-X and JT-60SA the economic benefit of HTS current leads was recognized after a 70 kA HTS current lead demonstrator was designed, fabricated and successfully tested by Karlsruhe Institute of Technology (KIT, which is a merge of former Forschungszentrum Karlsruhe and University of Karlsruhe). For ITER, the Chinese Domestic Agency will provide the current leads as a part of the superconducting feeder system. KIT is in charge of design, construction and test of HTS current leads for W7-X and JT-60SA. For W7-X 14 current leads with a maximum current of 18.2 kA are required that are oriented with the room temperature end at the bottom. JT60-SA will need 26 current leads (20 leads @ 20 kA and 6 leads @ 25.7 kA) which are mounted in vertical, normal position. These current leads are based on BiSCCO HTS superconductors, demonstrating that HTS material is now state of the art for highly efficient current leads. With respect to future fusion reactors, it would be very promising to use HTS material not only in current leads but also in coils. This would allow a large increase of efficiency if the coils could be operated at temperatures ?65 K. With such a high temperature it would be possible to omit the radiation shield of the coils, resulting in a less complex cryostat and a size reduction of the machine. In addition less refrigeration power is needed saving investment and operating costs. However, to come to an HTS fusion coil it is necessary to develop low ac loss HTS cables for currents well above 20 kA at high fields well above 10 T. The high field rules BiSCCO superconductors out at temperatures above 50 K, but RE-123 superconductors are promising. The development of a high current, high field RE-123 HTS fusion cable will not be targeted outside fusion community and has to be in the frame of a long term development programme for DEMO. KIT has already demonstrated a scalable concept using RE-123 HTS tapes that are assembled to Roebel type conductors. This concept can be expanded to form Rutherford cables as starting point for a development of a high current fusion cable. The status and prospect of using HTS conductors for fusion is discussed.

W.H. Fietz; R. Heller; S.I. Schlachter; W. Goldacker

2011-01-01T23:59:59.000Z

113

ANALYSIS OF FUTURE PRICES AND MARKETS FOR HIGH TEMPERATURE SUPERCONDUCTORS  

E-Print Network [OSTI]

1 ANALYSIS OF FUTURE PRICES AND MARKETS FOR HIGH TEMPERATURE SUPERCONDUCTORS BY JOSEPH MULHOLLAND of Future Prices and Markets for High Temperature Superconductors 2 I . PURPOSE, SCOPE AND APPROACH analysts to make estimates about the future of high temperature superconductor (HTS) technology

114

Free energy of QCD at high temperature  

Science Journals Connector (OSTI)

Effective-field-theory methods are used to separate the free energy for a non-Abelian gauge theory at high temperature T into the contributions from the momentum scales T, gT, and g2T, where g is the coupling constant at the scale 2?T. The effects of the scale T enter through the coefficients in the effective Lagrangian for the three-dimensional effective theory obtained by dimensional reduction. These coefficients can be calculated as power series in g2. The contribution to the free energy from the scale gT can be calculated using perturbative methods in the effective theory. It can be expressed as an expansion in g starting at order g3. The contribution from the scale g2T must be calculated using nonperturbative methods, but nevertheless it can be expanded in powers of g beginning at order g6. We calculate the free energy explicitly to order g5. We also outline the calculations necessary to obtain the free energy to order g6.

Eric Braaten and Agustin Nieto

1996-03-15T23:59:59.000Z

115

Scaling in high-temperature superconductors  

Science Journals Connector (OSTI)

A Hartree approximation is used to study the interplay of two kinds of scaling which arise in high-temperature superconductors, namely critical-point scaling and that due to the confinement of electron pairs to their lowest Landau level in the presence of an applied magnetic field. In the neighborhood of the zero-field critical point, thermodynamic functions scale with the scaling variable [T-Tc2(B)]/B1/2?, which differs from the variable [T-Tc(0)]/B1/2? suggested by the Gaussian approximation. Lowest-Landau-level (LLL) scaling occurs in a region of high field surrounding the upper critical-field line but not in the vicinity of the zero-field transition. For YBa2Cu3O7-? in particular, a field of at least 10 T is needed to observe LLL scaling. These results are consistent with a range of recent experimental measurements of the magnetization, transport properties, and, especially, the specific heat of high-Tc materials.

Ian D. Lawrie

1994-10-01T23:59:59.000Z

116

Development of Strengthened Bundle High Temperature Superconductors  

SciTech Connect (OSTI)

In the process of developing high temperature superconducting (HTS) transmission cables, it was found that mechanical strength of the superconducting tape is the most crucial property that needs to be improved. It is also desirable to increase the current carrying capacity of the conductor so that fewer layers are needed to make the kilo-amp class cables required for electric utility usage. A process has been developed by encapsulating a stack of Bi-2223/Ag tapes with a silver or non-silver sheath to form a strengthened bundle superconductor. This process was applied to HTS tapes made by the Continuous Tube Forming and Filling (CTFF) technique pursued by Plastronic Inc. and HTS tapes obtained from other manufacturers. Conductors with a bundle of 2 to 6 HTS tapes have been made. The bundled conductor is greatly strengthened by the non-silver sheath. No superconductor degradation as compared to the sum of the original critical currents of the individual tapes was seen on the finished conductors.

Lue, J.W.; Lubell, M.S. [Oak Ridge National Lab., TN (United States); Demko, J.A. [Oak Ridge Inst. for Science and Education, TN (United States); Tomsic, M. [Plastronic, Inc., Troy, OH (United States); Sinha, U. [Southwire Company, Carollton, GA (United States)

1997-12-31T23:59:59.000Z

117

Thermal stability of high temperature structural alloys  

SciTech Connect (OSTI)

High temperature structural alloys were evaluated for suitability for long term operation at elevated temperatures. The effect of elevated temperature exposure on the microstructure and mechanical properties of a number of alloys was characterized. Fe-based alloys (330 stainless steel, 800H, and mechanically alloyed MA 956), and Ni-based alloys (Hastelloy X, Haynes 230, Alloy 718, and mechanically alloyed MA 758) were evaluated for room temperature tensile and impact toughness properties after exposure at 750 C for 10,000 hours. Of the Fe-based alloys evaluated, 330 stainless steel and 800H showed secondary carbide (M{sub 23}C{sub 6}) precipitation and a corresponding reduction in ductility and toughness as compared to the as-received condition. Within the group of Ni-based alloys tested, Alloy 718 showed the most dramatic structure change as it formed delta phase during 10,000 hours of exposure at 750 C with significant reductions in strength, ductility, and toughness. Haynes 230 and Hastelloy X showed significant M{sub 23}C{sub 6} carbide precipitation and a resulting reduction in ductility and toughness. Haynes 230 was also evaluated after 10,000 hours of exposure at 850, 950, and 1050 C. For the 750--950 C exposures the M{sub 23}C{sub 6} carbides in Haynes 230 coarsened. This resulted in large reductions in impact strength and ductility for the 750, 850 and 950 C specimens. The 1050 C exposure specimens showed the resolution of M{sub 23}C{sub 6} secondary carbides, and mechanical properties similar to the as-received solution annealed condition.

Jordan, C.E.; Rasefske, R.K.; Castagna, A. [Lockheed Martin Corp., Schenectady, NY (United States)

1999-03-01T23:59:59.000Z

118

Vortices in high-temperature superconductors  

Science Journals Connector (OSTI)

With the high-temperature superconductors a qualitatively new regime in the phenomenology of type-II superconductivity can be accessed. The key elements governing the statistical mechanics and the dynamics of the vortex system are (dynamic) thermal and quantum fluctuations and (static) quenched disorder. The importance of these three sources of disorder can be quantified by the Ginzburg number Gi=(TcHc2??3)22, the quantum resistance Qu=(e2?)(?n??), and the critical current-density ratio jcjo, with jc and jo denoting the depinning and depairing current densities, respectively (?n is the normal-state resistivity and ?2=mMsuperconductors, leading to interesting effects such as the melting of the vortex lattice, the creation of new vortex-liquid phases, and the appearance of macroscopic quantum phenomena. Introducing quenched disorder into the system turns the Abrikosov lattice into a vortex glass, whereas the vortex liquid remains a liquid. The terms "glass" and "liquid" are defined in a dynamic sense, with a sublinear response ?=?E?j|j?0 characterizing the truly superconducting vortex glass and a finite resistivity ?(j?0)>0 being the signature of the liquid phase. The smallness of jcjo allows one to discuss the influence of quenched disorder in terms of the weak collective pinning theory. Supplementing the traditional theory of weak collective pinning to take into account thermal and quantum fluctuations, as well as the new scaling concepts for elastic media subject to a random potential, this modern version of the weak collective pinning theory consistently accounts for a large number of novel phenomena, such as the broad resistive transition, thermally assisted flux flow, giant and quantum creep, and the glassiness of the solid state. The strong layering of the oxides introduces additional new features into the thermodynamic phase diagram, such as a layer decoupling transition, and modifies the mechanism of pinning and creep in various ways. The presence of strong (correlated) disorder in the form of twin boundaries or columnar defects not only is technologically relevant but also provides the framework for the physical realization of novel thermodynamic phases such as the Bose glass. On a macroscopic scale the vortex system exhibits self-organized criticality, with both the spatial and the temporal scale accessible to experimental investigations.

G. Blatter; M. V. Feigel'man; V. B. Geshkenbein; A. I. Larkin; V. M. Vinokur

1994-10-01T23:59:59.000Z

119

High Temperature Oxidation Performance of Aluminide Coatings  

SciTech Connect (OSTI)

Aluminide coatings are of interest for many high temperature applications because of the possibility of improving the oxidation resistance of structural alloys by forming a protective external alumina scale. Steam and exhaust gas environments are of particular interest because alumina is less susceptible to the accelerated attack due to hydroxide formation observed for chromia- and silica-forming alloys and ceramics. For water vapor testing, one ferritic (Fe-9Cr-1Mo) and one austenitic alloy (304L) have been selected as substrate materials and CVD coatings have been used in order to have a well-controlled, high purity coating. It is anticipated that similar aluminide coatings could be made by a higher-volume, commercial process such as pack cementation. Previous work on this program has examined as-deposited coatings made by high and low Al activity CVD processes and the short-term performance of these coatings. The current work is focusing on the long term behavior in both diffusion tests16 and oxidation tests of the thicker, high Al activity coatings. For long-term coating durability, one area of concern has been the coefficient of thermal expansion (CTE) mismatch between coating and substrate. This difference could cause cracking or deformation that could reduce coating life. Corrosion testing using thermal cycling is of particular interest because of this potential problem and results are presented where a short exposure cycle (1h) severely degraded aluminide coatings on both types of substrates. To further study the potential role of aluminide coatings in fossil energy applications, several high creep strength Ni-base alloys were coated by CVD for testing in a high pressure (20atm) steam-CO{sub 2} environment for the ZEST (zero-emission steam turbine) program. Such alloys would be needed as structural and turbine materials in this concept. For Ni-base alloys, CVD produces a {approx}50{mu}m {beta}-NiAl outer layer with an underlying interdiffusion zone. Specimens of HR160, alloy 601 and alloy 230 were tested with and without coatings at 900 C and preliminary post-test characterization is reported.

Pint, Bruce A [ORNL; Zhang, Ying [Tennessee Technological University; Haynes, James A [ORNL; Wright, Ian G [ORNL

2004-01-01T23:59:59.000Z

120

Fuel Cell Technologies Office: 2005 High Temperature Membrane Working Group  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

About About Printable Version Share this resource Send a link to Fuel Cell Technologies Office: 2005 High Temperature Membrane Working Group Meeting Archives to someone by E-mail Share Fuel Cell Technologies Office: 2005 High Temperature Membrane Working Group Meeting Archives on Facebook Tweet about Fuel Cell Technologies Office: 2005 High Temperature Membrane Working Group Meeting Archives on Twitter Bookmark Fuel Cell Technologies Office: 2005 High Temperature Membrane Working Group Meeting Archives on Google Bookmark Fuel Cell Technologies Office: 2005 High Temperature Membrane Working Group Meeting Archives on Delicious Rank Fuel Cell Technologies Office: 2005 High Temperature Membrane Working Group Meeting Archives on Digg Find More places to share Fuel Cell Technologies Office: 2005 High

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Fuel Cell Technologies Office: 2004 High Temperature Membrane Working Group  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

About About Printable Version Share this resource Send a link to Fuel Cell Technologies Office: 2004 High Temperature Membrane Working Group Meeting Archives to someone by E-mail Share Fuel Cell Technologies Office: 2004 High Temperature Membrane Working Group Meeting Archives on Facebook Tweet about Fuel Cell Technologies Office: 2004 High Temperature Membrane Working Group Meeting Archives on Twitter Bookmark Fuel Cell Technologies Office: 2004 High Temperature Membrane Working Group Meeting Archives on Google Bookmark Fuel Cell Technologies Office: 2004 High Temperature Membrane Working Group Meeting Archives on Delicious Rank Fuel Cell Technologies Office: 2004 High Temperature Membrane Working Group Meeting Archives on Digg Find More places to share Fuel Cell Technologies Office: 2004 High

122

Fuel Cell Technologies Office: 2010 High Temperature Membrane Working Group  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

About About Printable Version Share this resource Send a link to Fuel Cell Technologies Office: 2010 High Temperature Membrane Working Group Meeting Archives to someone by E-mail Share Fuel Cell Technologies Office: 2010 High Temperature Membrane Working Group Meeting Archives on Facebook Tweet about Fuel Cell Technologies Office: 2010 High Temperature Membrane Working Group Meeting Archives on Twitter Bookmark Fuel Cell Technologies Office: 2010 High Temperature Membrane Working Group Meeting Archives on Google Bookmark Fuel Cell Technologies Office: 2010 High Temperature Membrane Working Group Meeting Archives on Delicious Rank Fuel Cell Technologies Office: 2010 High Temperature Membrane Working Group Meeting Archives on Digg Find More places to share Fuel Cell Technologies Office: 2010 High

123

Fuel Cell Technologies Office: 2007 High Temperature Membrane Working Group  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

About About Printable Version Share this resource Send a link to Fuel Cell Technologies Office: 2007 High Temperature Membrane Working Group Meeting Archives to someone by E-mail Share Fuel Cell Technologies Office: 2007 High Temperature Membrane Working Group Meeting Archives on Facebook Tweet about Fuel Cell Technologies Office: 2007 High Temperature Membrane Working Group Meeting Archives on Twitter Bookmark Fuel Cell Technologies Office: 2007 High Temperature Membrane Working Group Meeting Archives on Google Bookmark Fuel Cell Technologies Office: 2007 High Temperature Membrane Working Group Meeting Archives on Delicious Rank Fuel Cell Technologies Office: 2007 High Temperature Membrane Working Group Meeting Archives on Digg Find More places to share Fuel Cell Technologies Office: 2007 High

124

First high-temperature electronics products survey 2005.  

SciTech Connect (OSTI)

On April 4-5, 2005, a High-Temperature Electronics Products Workshop was held. This workshop engaged a number of governmental and private industry organizations sharing a common interest in the development of commercially available, high-temperature electronics. One of the outcomes of this meeting was an agreement to conduct an industry survey of high-temperature applications. This report covers the basic results of this survey.

Normann, Randy Allen

2006-04-01T23:59:59.000Z

125

High Temperature, High Pressure Devices for Zonal Isolation in...  

Open Energy Info (EERE)

remotely and autonomous deployable structures for space and our high temperature composite technology developed for downhole applications. These devices offer several...

126

Overview of Fraunhofer IPM Activities in High Temperature Bulk...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Workshop including an overview about Fraunhofer IPM, new funding situation in Germany, high temperature material and modules, energy-autarkic sensors, and thermoelectric...

127

Development of a 500 Watt High Temperature Thermoelectric Generator...  

Broader source: Energy.gov (indexed) [DOE]

More Documents & Publications Development of a 100-Watt High Temperature Thermoelectric Generator Automotive Waste Heat Conversion to Power Program Automotive Waste Heat...

128

Institute of Chemical Engineering and High Temperature Chemical...  

Open Energy Info (EERE)

Chemical Processes ICEHT Jump to: navigation, search Name: Institute of Chemical Engineering and High Temperature Chemical Processes (ICEHT) Place: Hellas, Greece Zip:...

129

Evaluation of High-Temperature Alloys for Helium Gas Turbines  

Science Journals Connector (OSTI)

C. 1. Mechanical Property / Status of Metallic Materials Development for Application in Advanced High-Temperature Gas-Cooled Reactor / Material

Wolfgang Jakobeit; Jörn-Peter Pfeifer; Georg Ullrich

130

High-Temperature, Air-Cooled Traction Drive Inverter Packaging...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Temperature, Air-Cooled Traction Drive Inverter Packaging High-Temperature, Air-Cooled Traction Drive Inverter Packaging 2010 DOE Vehicle Technologies and Hydrogen Programs Annual...

131

High Temperature Superconducting Fault Current Limiter for Utility Applications  

Science Journals Connector (OSTI)

One of the most near term High Temperature Superconductor (HTS) applications is the Fault Current Limiter (FCL). It is a device that...

E. M. W. Leung; G. W. Albert; M. Dew…

1997-01-01T23:59:59.000Z

132

Fundamental Corrosion Studies in High-Temperature Molten Salt...  

Broader source: Energy.gov (indexed) [DOE]

Studies in High-Temperature Molten Salt Systems for CSP Applications Savannah River National Laboratory April 15, 2013 | Garcia-Diaz * The overall project approach will combine...

133

Corrosion Studies in High-Temperature Molten Salt Systems for...  

Broader source: Energy.gov (indexed) [DOE]

Studies in High-Temperature Molten Salt Systems for CSP Applications Savannah River National Laboratory Garcia-Diaz A 1152013:Garcia-Diaz * The overall project approach will...

134

High Temperature Superconductor Cable Concepts for Fusion Magnets.  

E-Print Network [OSTI]

??Three concepts of high temperature superconductor cables carrying kA currents (RACC, CORC and TSTC) are investigated, optimized and evaluated in the scope of their applicability… (more)

Barth, Christian

2013-01-01T23:59:59.000Z

135

Solid oxide steam electrolysis for high temperature hydrogen production .  

E-Print Network [OSTI]

??This study has focused on solid oxide electrolyser cells for high temperature steam electrolysis. Solid oxide electrolysis is the reverse operation of solid oxide fuel… (more)

Eccleston, Kelcey L.

2007-01-01T23:59:59.000Z

136

Detecting Fractures Using Technology at High Temperatures and...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Fractures Using Technology at High Temperatures and Depths - Geothermal Ultrasonic Fracture Imager (GUFI); 2010 Geothermal Technology Program Peer Review Report Detecting...

137

Detecting Fractures Using Technology at High Temperatures and...  

Broader source: Energy.gov (indexed) [DOE]

Fractures Using Technology at High Temperatures and Depths - Geothermal Ultrasonic Fracture Imager (GUFI) Presentation Number: 015 Investigator: Patterson, Doug (Baker Hughes...

138

High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems  

Broader source: Energy.gov [DOE]

High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems presentation at the April 2013 peer review meeting held in Denver, Colorado.

139

Nanostructured High-Temperature Bulk Thermoelectric Energy Conversion...  

Broader source: Energy.gov (indexed) [DOE]

High Temperature Bulk Thermoelectric Energy Conversion for Efficient Waste Heat Recovery Project Overview 2 * Start: October 2011 * End: September 2015 * Percent complete -...

140

Feasibility and Design Studies for a High Temperature Downhole Tool  

Broader source: Energy.gov [DOE]

Project objective: Perform feasibility and design studies for a high temperature downhole tool; which uses nuclear techniques for characterization purposes; using measurements and modeling/simulation.

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

High-Temperature Aluminum Alloys | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting pm044smith2012o.pdf More Documents & Publications High-Temperature Aluminum Alloys Vehicle...

142

High-Temperature-High-Volume Lifting for Enhanced Geothermal...  

Broader source: Energy.gov (indexed) [DOE]

Norman Turnquist GE Global Research High Temperature Tools and Sensors, Down-hole Pumps and Drilling May 19, 2010 This presentation does not contain any proprietary...

143

ANALYSIS OF A HIGH TEMPERATURE GAS-COOLED REACTOR POWERED HIGH TEMPERATURE ELECTROLYSIS HYDROGEN PLANT  

SciTech Connect (OSTI)

An updated reference design for a commercial-scale high-temperature electrolysis (HTE) plant for hydrogen production has been developed. The HTE plant is powered by a high-temperature gas-cooled reactor (HTGR) whose configuration and operating conditions are based on the latest design parameters planned for the Next Generation Nuclear Plant (NGNP). The current HTGR reference design specifies a reactor power of 600 MWt, with a primary system pressure of 7.0 MPa, and reactor inlet and outlet fluid temperatures of 322°C and 750°C, respectively. The reactor heat is used to produce heat and electric power to the HTE plant. A Rankine steam cycle with a power conversion efficiency of 44.4% was used to provide the electric power. The electrolysis unit used to produce hydrogen includes 1.1 million cells with a per-cell active area of 225 cm2. The reference hydrogen production plant operates at a system pressure of 5.0 MPa, and utilizes a steam-sweep system to remove the excess oxygen that is evolved on the anode (oxygen) side of the electrolyzer. The overall system thermal-to-hydrogen production efficiency (based on the higher heating value of the produced hydrogen) is 42.8% at a hydrogen production rate of 1.85 kg/s (66 million SCFD) and an oxygen production rate of 14.6 kg/s (33 million SCFD). An economic analysis of this plant was performed with realistic financial and cost estimating The results of the economic analysis demonstrated that the HTE hydrogen production plant driven by a high-temperature helium-cooled nuclear power plant can deliver hydrogen at a competitive cost. A cost of $3.03/kg of hydrogen was calculated assuming an internal rate of return of 10% and a debt to equity ratio of 80%/20% for a reactor cost of $2000/kWt and $2.41/kg of hydrogen for a reactor cost of $1400/kWt.

M. G. McKellar; E. A. Harvego; A. M. Gandrik

2010-11-01T23:59:59.000Z

144

Vibration Combined High Temperature Cycle Tests for Capacitive MEMS  

E-Print Network [OSTI]

Vibration Combined High Temperature Cycle Tests for Capacitive MEMS Accelerometers Z. Szcs, G. Nagy|nagyg|hodossy|rencz|poppe>@eet.bme.hu Abstract - In this paper vibration combined high temperature cycle tests for packaged capacitive SOI- MEMS designed and realized at BME ­ DED. Twenty thermal cycles of combined Temperature Cycle Test and Fatigue

Boyer, Edmond

145

POWER-TO-GAS PROCESS WITH HIGH TEMPERATURE ELECTROLYSIS  

E-Print Network [OSTI]

POWER-TO-GAS PROCESS WITH HIGH TEMPERATURE ELECTROLYSIS AND CO2 METHANATION NOVEMBER 19th 2013 IRES. Energy background 2. Power-to-Substitute Natural Gas process with high temperature steam electrolysis Gas-to-heat Gas-to-mobility Gas-to-power Excess Production = Consumption Distribution and storing

Paris-Sud XI, Université de

146

High Temperature Evaluation of Tantalum Capacitors - Test 1  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

Tantalum capacitors can provide much higher capacitance at high-temperatures than the ceramic capacitors. This study evaluates selected tantalum capacitors at high temperatures to determine their suitability for you in geothermal field. This data set contains results of the first test where three different types of capacitors were evaluated at 260C.

Grzegorz Cieslewski

147

Vibrational Raman Spectroscopy of High-temperature Superconductors  

E-Print Network [OSTI]

Vibrational Raman Spectroscopy of High-temperature Superconductors C. Thomsen and G. Kaczmarczyk after the discovery of high- critical-temperature Tc superconductors:2 while reports on Raman scattering Wiley & Sons Ltd, Chichester, 2002 #12;Vibrational Raman Spectroscopy of High-temperature

Nabben, Reinhard

148

High Temperature Evaluation of Tantalum Capacitors - Test 1  

SciTech Connect (OSTI)

Tantalum capacitors can provide much higher capacitance at high-temperatures than the ceramic capacitors. This study evaluates selected tantalum capacitors at high temperatures to determine their suitability for you in geothermal field. This data set contains results of the first test where three different types of capacitors were evaluated at 260C.

Cieslewski, Grzegorz

2014-09-28T23:59:59.000Z

149

To Crack or Not to Crack: Strain in High Temperature Superconductors  

E-Print Network [OSTI]

Strain in High Temperature Superconductors Arno GodekeCrack: Strain in High Temperature Superconductors MotivationCrack: Strain in High Temperature Superconductors How do Nb

Godeke, Arno

2008-01-01T23:59:59.000Z

150

X-ray diffuse scattering studies of the local structural inhomogeneities in high temperature superconductors  

E-Print Network [OSTI]

in high temperature superconductors A dissertation submittedChemistry of High-Temperature Superconductors. Word Scienti?work on the high temperature superconductors, one of the

Liu, Xuerong

2009-01-01T23:59:59.000Z

151

Advancing the technology base for high-temperature membranes  

SciTech Connect (OSTI)

This is the final report of a two-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). This project addresses the major issues confronting the implementation of high-temperature membranes for separations and catalysis. We are pursuing high-temperature membrane systems that can have a large impact for DOE and be industrially relevant. A major obstacle for increased use of membranes is that most applications require the membrane material to withstand temperatures above those acceptable for polymer-based systems. Advances made by this project have helped industry and DOE move toward high-temperature membrane applications to improve overall energy efficiency.

Dye, R.C.; Birdsell, S.A.; Snow, R.C. [and others

1997-10-01T23:59:59.000Z

152

Thermomagnetic phenomena in the mixed state of high temperature superconductors  

SciTech Connect (OSTI)

Galvano- and thermomagnetic-phenomena in high temperature superconductors, based on kinetic coefficients, are discussed, along with a connection between the electric field and the heat flow in superconductor mixed state. The relationship that determines the transport coefficients of high temperature superconductors in the mixed state based on Seebeck and Nernst effects is developed. It is shown that this relationship is true for a whole transition region of the resistive mixed state of a superconductor. Peltier, Ettingshausen and Righi-Leduc effects associated with heat conductivity as related to high temperature superconductors are also addressed.

Meilikhov, E.Z.

1995-04-01T23:59:59.000Z

153

Method for Synthesizing Extremeley High Temperature Melting Materials  

DOE Patents [OSTI]

The invention relates to a method of synthesizing high-temperature melting materials. More specifically the invention relates to a containerless method of synthesizing very high temperature melting materials such as borides, carbides and transition-metal, lanthanide and actinide oxides, using an Aerodynamic Levitator and a laser. The object of the invention is to provide a method for synthesizing extremely high-temperature melting materials that are otherwise difficult to produce, without the use of containers, allowing the manipulation of the phase (amorphous/crystalline/metastable) and permitting changes of the environment such as different gaseous compositions.

Saboungi, Marie-Louise and Glorieux, Benoit

2005-11-22T23:59:59.000Z

154

Method For Synthesizing Extremely High-Temperature Melting Materials  

DOE Patents [OSTI]

The invention relates to a method of synthesizing high-temperature melting materials. More specifically the invention relates to a containerless method of synthesizing very high temperature melting materials such as borides, carbides and transition-metal, lanthanide and actinide oxides, using an Aerodynamic Levitator and a laser. The object of the invention is to provide a method for synthesizing extremely high-temperature melting materials that are otherwise difficult to produce, without the use of containers, allowing the manipulation of the phase (amorphous/crystalline/metastable) and permitting changes of the environment such as different gaseous compositions.

Saboungi, Marie-Louise (Chicago, IL); Glorieux, Benoit (Perpignan, FR)

2005-11-22T23:59:59.000Z

155

Method for synthesizing extremely high-temperature melting materials  

SciTech Connect (OSTI)

The invention relates to a method of synthesizing high-temperature melting materials. More specifically the invention relates to a containerless method of synthesizing very high temperature melting materials such as carbides and transition-metal, lanthanide and actinide oxides, using an aerodynamic levitator and a laser. The object of the invention is to provide a method for synthesizing extremely high-temperature melting materials that are otherwise difficult to produce, without the use of containers, allowing the manipulation of the phase (amorphous/crystalline/metastable) and permitting changes of the environment such as different gaseous compositions.

Saboungi, Marie-Louise (Chicago, IL); Glorieux, Benoit (Perpignan, FR)

2007-11-06T23:59:59.000Z

156

Fuel Cell Technologies Office: High Temperature Membrane Working Group  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

High Temperature Membrane Working Group High Temperature Membrane Working Group The High Temperature Membrane Working Group consists of government, industry, and university researchers interested in developing high temperature membranes for fuel cells. Description Technical Targets Meetings Contacts Description Polymer electrolyte membrane (PEM) fuel cells typically operate at temperatures no higher than 60°C-80°C due to structural limitations of the membrane. Operating PEM fuel cell stacks at higher temperatures (120°C for transportation and 150°C for stationary applications), however, would yield significant energy benefits. For example, heat rejection is easier at higher temperatures, which would allow use of smaller heat exchangers in fuel cell power systems. In addition, for reformate fuel cell systems, carbon monoxide (CO) tolerance of the stack is less problematic at higher temperatures, which would reduce the size requirements or possibly eliminate the need for some CO clean-up beds in the fuel processor.

157

High Temperature Corrosion Test Facilities and High Pressure Test  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

High Temperature High Temperature Corrosion Test Facilities and High Pressure Test Facilities for Metal Dusting Test Facilities for Metal Dusting Overview Other Facilities Work with Argonne Contact us For Employees Site Map Help Join us on Facebook Follow us on Twitter NE on Flickr High Temperature Corrosion Test Facilities and High Pressure Test Facilities for Metal Dusting Six corrosion test facilities and two thermogravimetric systems for conducting corrosion tests in complex mixed gas environments, in steam and in the presence of deposits, and five facilities for metal dusting degradation Bookmark and Share The High Temperature Corrosion Test Facilities and High Pressure Test Facilities for Metal Dusting include: High Pressure Test Facility for Metal Dusting Resistance:

158

DOE Hydrogen Analysis Repository: High Temperature Electrolysis (HTE)  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

High Temperature Electrolysis (HTE) High Temperature Electrolysis (HTE) Project Summary Full Title: High Temperature Electrolysis (HTE) Project ID: 159 Principal Investigator: Steve Herring Brief Description: A three-dimensional computational fluid dynamics (CFD) model was created to model high-temperature steam electrolysis in a planar solid oxide electrolysis cell (SOEC). A solid-oxide fuel cell model adds the electrochemical reactions and loss mechanisms and computation of the electric field throughout the cell. Keywords: Solid oxide fuel cell; solid oxide elctrolysis cell; nuclear; model Purpose Assess the performance of solid-oxide cells operating in the steam electrolysis mode for hydrogen production over a temperature range of 800 to 900ÂșC. Performer Principal Investigator: Steve Herring

159

Thermodynamics and Transport Phenomena in High Temperature Steam Electrolysis Cells  

SciTech Connect (OSTI)

Hydrogen can be produced from water splitting with relatively high efficiency using high temperature electrolysis. This technology makes use of solid-oxide cells, running in the electrolysis mode to produce hydrogen from steam, while consuming electricity and high temperature process heat. The overall thermal-to-hydrogen efficiency for high temperature electrolysis can be as high as 50%, which is about double the overall efficiency of conventional low-temperature electrolysis. Current large-scale hydrogen production is based almost exclusively on steam reforming of methane, a method that consumes a precious fossil fuel while emitting carbon dioxide to the atmosphere. An overview of high temperature electrolysis technology will be presented, including basic thermodynamics, experimental methods, heat and mass transfer phenomena, and computational fluid dynamics modeling.

James E. O'Brien

2012-03-01T23:59:59.000Z

160

High Temperature Superconducting Racetrack Coils for Electric Motor Applications  

Science Journals Connector (OSTI)

American Superconductor Corporation (ASC) has designed and fabricated racetrack-shaped field coils from PbBSSCO-2223 high temperature superconducting (HTS) wire for a 125 HP, four-pole motor currently being devel...

J. P. Voccio; C. B. Prum; M. J. Navarro…

1997-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

High-temperature neutron diffraction study of deuterated brucite  

Science Journals Connector (OSTI)

To study the structural behavior of brucite at high temperature, we conducted in situ neutron diffraction experiments of a deuterated brucite powder sample, Mg(OD)2, in the temperature range 313–583 K. The sample...

Hongwu Xu; Yusheng Zhao; Donald D. Hickmott…

2013-11-01T23:59:59.000Z

162

High Temperature Fuel Cell (Phosphoric Acid) Manufacturing R...  

Broader source: Energy.gov (indexed) [DOE]

Fuel Cell (Phosphoric Acid) Manufacturing R&D High Temperature Fuel Cell (Phosphoric Acid) Manufacturing R&D Presented at the NREL Hydrogen and Fuel Cell Manufacturing R&D Workshop...

163

Cryogenic deformation of high temperature superconductive composite structures  

DOE Patents [OSTI]

An improvement in a process of preparing a composite high temperature oxide superconductive wire is provided and involves conducting at least one cross-sectional reduction step in the processing preparation of the wire at sub-ambient temperatures.

Roberts, Peter R. (Groton, MA); Michels, William (Brookline, MA); Bingert, John F. (Jemez Springs, NM)

2001-01-01T23:59:59.000Z

164

Structural Integrity Assessment of Very High Temperature Nuclear...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Structural Integrity Assessment of Very High Temperature Nuclear Reactor Core Components Oct 20 2014 09:00 AM - 10:00 AM Gyanendar Singh, The University of Minnesota, Minneapolis...

165

Copper Aluminate as a potential material for high temperature...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Copper Aluminate as a potential material for high temperature thermoelectric power generation Home Author: D. T. Morelli, E. D. Case, B. D. Hall, S. Wang Year: 2008 Abstract: URL:...

166

Mold, flow, and economic considerations in high temperature precision casting  

E-Print Network [OSTI]

Casting high temperature alloys that solidify through a noticeable two phase region, specifically platinum-ruthenium alloys, is a particularly challenging task due to their high melting temperature and this necessitates ...

Humbert, Matthew S

2013-01-01T23:59:59.000Z

167

18th Topical Conference High-Temperature Plasma Diagnostics ...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

May 16, 2010, 9:00am to May 20, 2010, 5:00pm Conference Wildwood, New Jersey 18th Topical Conference High-Temperature Plasma Diagnostics (HTPD) The 18th Topical Conference on...

168

Electronic properties of doped Mott insulators and high temperature superconductors  

E-Print Network [OSTI]

High-temperature superconducting cuprates, which are the quintessential example of a strongly correlated system and the most extensively studied materials after semiconductors, spurred the development in the fields of ...

Ribeiro, Tiago Castro

2005-01-01T23:59:59.000Z

169

Cryocooler Applications for High-Temperature Superconductor Magnetic Bearings  

Science Journals Connector (OSTI)

The efficiency and stability of rotational magnetic suspension systems are enhanced by the use of high-temperature superconductor (HTS) magnetic bearings. Fundamental aspects of ... aspects to be considered are i...

R. C. Niemann; J. R. Hull

2002-01-01T23:59:59.000Z

170

Growth of high-temperature superconductor crystals from flux  

Science Journals Connector (OSTI)

Crystallization of high-temperature superconductors was studied in La-Sr-Cu-O,...2Cu3O6.5+x were obtained by spontaneous crystallization from homogeneous nonstoichiometric melts enriched in bariu...

L N Demianets; A B Bykov; O K Melnikov; S M Stishov

1991-04-01T23:59:59.000Z

171

Engineering Design of A High-Temperature Superconductor Current Lead  

Science Journals Connector (OSTI)

As part of the U.S. Department of Energy’s Superconductivity Pilot Center Program, Argonne National Laboratory and Superconductivity, Inc., are developing high-temperature superconductor (HTS) current leads suita...

R. C. Niemann; Y. S. Cha; J. R. Hull; M. A. Daugherty; W. E. Buckles

1994-01-01T23:59:59.000Z

172

Experimental demonstration of vortex pancake in high temperature superconductor  

Science Journals Connector (OSTI)

In order to demonstrate the existence of the vortex pancake in high temperature superconductor experimentally, a configuration in which the current...E-j relation obtained with this electrodes spatial configurati...

Wei-xian Wang; Yu-heng Zhang

2006-09-01T23:59:59.000Z

173

High-temperature superconductor applications development at Argonne National Laboratory  

SciTech Connect (OSTI)

Developments at Argonne National Laboratory of near and intermediate term applications using high-temperature superconductors are discussed. Near-term applications of liquid-nitrogen depth sensors, current leads, and magnetic bearings are discussed in detail.

Hull, J.R.; Poeppel, R.B.

1992-02-09T23:59:59.000Z

174

High temperature solid electrolyte fuel cell configurations and interconnections  

DOE Patents [OSTI]

High temperature fuel cell configurations and interconnections are made including annular cells having a solid electrolyte sandwiched between thin film electrodes. The cells are electrically interconnected along an elongated axial outer surface.

Isenberg, Arnold O. (Forest Hills, PA)

1984-01-01T23:59:59.000Z

175

High-Temperature Thermal Array for Next Generation Solar Thermal...  

Broader source: Energy.gov (indexed) [DOE]

3 Q1 High-Temperature Thermal Array for Next Generation Solar Thermal Power Production - FY13 Q1 This document summarizes the progress of this Los Alamos National Laboratory...

176

Stability and quench protection of high-temperature superconductors  

E-Print Network [OSTI]

In the design and operation of a superconducting magnet, stability and protection are two key issues that determine the magnet's reliability and safe operation. Although the high-temperature superconductor (HTS) is considered ...

Ang, Ing Chea

2006-01-01T23:59:59.000Z

177

Next-generation nuclear fuel withstands high-temperature accident...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

teri.ehresman@inl.gov Bill Cabage (ORNL), 865-574-4399, cabagewh@ornl.gov Next-generation nuclear fuel withstands high-temperature accident conditions IDAHO FALLS - A safer...

178

Computational and Experimental Development of Novel High-Temperature Alloys  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Development of Novel High-Temperature Alloys Background The need for fossil-fueled power plants to run cleaner and more efficiently leads toward ever-higher operating temperatures and pressures. Gas turbines, which can be fueled by natural gas, synthetic gas (syngas), or a high-hydrogen stream derived from coal, are critical components in this development. High-temperature operation of turbines is generally achieved by using nickel-chrome superalloys with coatings

179

Low GWP Working Fluid for High Temperature Heat Pumps  

E-Print Network [OSTI]

Low GWP Working Fluid for High Temperature Heat Pumps: DR-2 Chemical Stability at High Temperatures Temp Heat Pumps: DR-2 Very Low GWP AND Non-Flammable HFC-245fa DR-2 Chemical Formula CF3CH2CHF2 HFO 171.3 Pcr [MPa] 3.65 2.9 Kontomaris-DuPont; European Heat Pump Summit, Nuremberg, October 15th, 2013

Oak Ridge National Laboratory

180

Electron-Phonon Coupling in High-Temperature Cuprate Superconductors as Revealed by Angle-resolved Photoemisson Spectroscopy  

E-Print Network [OSTI]

Cuprate oxide high-temperature superconductors are dopedsuperconductivity. High temperature superconductors arein understanding high-temperature superconductors, such as

Zhou, X.J.; Hussain, Z.; Shen, Z.-X.

2005-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Non-graphite crucible for high temperature applications  

DOE Patents [OSTI]

A multi-piece crucible for high temperature applications comprises a tubular side wall member having a lip on the inside surface and a bottom member or members forming a container for containing a melt of a material during a high temperature melt-casting operations. The multi-piece design prevents cracking of the crucible or leakage of the melt from the crucible during the melt-casting operation. The lip of the tubular member supports the bottom member. The contacting surfaces where the lip of the tubular side wall member contacts the bottom member of the multi-piece crucible contains a ceramic sealing material. The ceramic sealing material forms a seal sufficient to prevent the melt of the material from leaking out of the multi-piece crucible during the melt-casting process. The multi-piece crucible is made of a material which is chemically inert to the melt and has structural integrity at the melting point temperature of the melt, or of a material coated with such a material. The multi-piece crucible is contained in a thermal can assembly of a high temperature induction furnace during a high temperature melt-casting operation. One embodiment of the multi-piece crucible comprises a tubular member having a vertical slot filled with a ceramic sealing material to provide expansion of the tubular member without cracking during the high temperature melt-casting operation. 9 figs.

Holcombe, C.E.; Pfeiler, W.A.

1996-01-09T23:59:59.000Z

182

The Northwest Geysers High-Temperature Reservoir- Evidence For Active  

Open Energy Info (EERE)

Geysers High-Temperature Reservoir- Evidence For Active Geysers High-Temperature Reservoir- Evidence For Active Magmatic Degassing And Implications For The Origin Of The Geysers Geothermal Field Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: The Northwest Geysers High-Temperature Reservoir- Evidence For Active Magmatic Degassing And Implications For The Origin Of The Geysers Geothermal Field Details Activities (2) Areas (1) Regions (0) Abstract: Noble gas isotope abundances in steam from the Coldwater Creek field of the Northwest Geysers, California, show mixing between a nearly pure mid-ocean ridge (MOR) type magmatic gas with high 3He/4He and low radiogenic 40*Ar (R/Ra > 8.3 and 40*Ar/4He < 0.07), and a magmatic gas diluted with crustal gas (R/Ra 0.25). The

183

High-Temperature Downhole Tools | Open Energy Information  

Open Energy Info (EERE)

Tools Tools Jump to: navigation, search Contents 1 Geothermal Lab Call Projects for High-Temperature Downhole Tools 2 Geothermal ARRA Funded Projects for High-Temperature Downhole Tools Geothermal Lab Call Projects for High-Temperature Downhole Tools Loading map... {"format":"googlemaps3","type":"ROADMAP","types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"limit":200,"offset":0,"link":"all","sort":[""],"order":[],"headers":"show","mainlabel":"","intro":"","outro":"","searchlabel":"\u2026 further results","default":"","geoservice":"google","zoom":false,"width":"600px","height":"350px","centre":false,"layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","icon":"","visitedicon":"","forceshow":true,"showtitle":true,"hidenamespace":false,"template":false,"title":"","label":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"locations":[{"text":"

184

DOE Science Showcase - Understanding High-Temperature Superconductors |  

Office of Scientific and Technical Information (OSTI)

Understanding High-Temperature Superconductors Understanding High-Temperature Superconductors Credit: DOE Scientists have long worked to understand one of the great mysteries of modern physics - the origin and behavior of high-temperature superconductors (HTS) that are uniquely capable of transmitting electricity with zero loss when chilled to subzero temperatures. For decades there have been competing theories and misunderstandings of how HTS materials actually work and they have remained fundamentally puzzling to physicists. Solving this mystery has the potential to revolutionize the planet's energy infrastructure from generation to transmission and grid-scale storage. Recent technical breakthroughs in this quest are being discovered by DOE scientists and their collaborators. Read about HTS technology, basic

185

Fabrication and Characterization of Uranium-based High Temperature Reactor  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Fabrication and Characterization of Uranium-based High Temperature Reactor Fabrication and Characterization of Uranium-based High Temperature Reactor Fuel June 01, 2013 The Uranium Fuel Development Laboratory is a modern R&D scale lab for the fabrication and characterization of uranium-based high temperature reactor fuel. A laboratory-scale coater manufactures tri-isotropic (TRISO) coated fuel particles (CFPs), state-of-the-art materials property characterization is performed, and the CFPs are then pressed into fuel compacts for irradiation testing, all under a NQA-1 compliant Quality Assurance Program. After fuel kernel size and shape are measured by optical shadow imaging, the TRISO coatings are deposited via fluidized bed chemical vapor deposition in a 50-mm diameter conical chamber within the coating furnace. Computer control of temperature and gas composition ensures reproducibility

186

High-Temperature-High-Volume Lifting | Open Energy Information  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » High-Temperature-High-Volume Lifting Jump to: navigation, search Geothermal ARRA Funded Projects for High-Temperature-High-Volume Lifting Loading map... {"format":"googlemaps3","type":"ROADMAP","types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"limit":200,"offset":0,"link":"all","sort":[""],"order":[],"headers":"show","mainlabel":"","intro":"","outro":"","searchlabel":"\u2026

187

Margins in high temperature leak-before-break assessments  

SciTech Connect (OSTI)

Developments in the defect assessment procedure R6 to include high-temperature mechanisms in Leak-before-Break arguments are described. In particular, the effect of creep on the time available to detect a leak and on the crack opening area, and hence leak rate, is discussed. The competing influence of these two effects is emphasized by an example. The application to Leak-before-Break of the time-dependent failure assessment diagram approach for high temperature defect assessment is then outlined. The approach is shown to be of use in assessing the erosion of margins by creep.

Budden, P.J.; Hooton, D.G.

1997-04-01T23:59:59.000Z

188

Electronic-Structure of High-Temperature Superconductors  

E-Print Network [OSTI]

, and for the corresponding metal atoms in related high-temperature superconductors. These peaks should be observable in electron energy-loss spectroscopy's and 6nal-state photoemission spectrosco- py 20 The calculated valences d,n are again given in Table II. Notice... again neatly cancel in YBa2Cu307. In summary, we have calculated the electronic struc- tures of the most typical members of the two known classes of high-temperature superconductors. The present results, obtained with a simple tight-binding model...

RICHERT, BA; Allen, Roland E.

1988-01-01T23:59:59.000Z

189

High temperature alkali corrosion of ceramics in coal gas  

SciTech Connect (OSTI)

The high temperature alkali corrosion kinetics of SiC have been systematically investigated from 950 to 1100[degrees]C at 0.63 vol % alkali vapor concentration. The corrosion rate in the presence of alkaliis approximately 10[sup 4] to 10[sup 5] times faster than the oxidation rate of SiC in air. The activation energy associated with the alkali corrosion is 406 kJ/mol, indicating a highly temperature-dependent reaction rate. The rate-controlling step of the overall reaction is likely to be the dissolution of silica in the sodium silicate liquid, based on the oxygen diffusivity data.

Pickrell, G.R.; Sun, T.; Brown, J.J.

1992-02-24T23:59:59.000Z

190

High temperature alkali corrosion of ceramics in coal gas  

SciTech Connect (OSTI)

High temperature alkali corrosion has been known to cause premature failure of ceramic components used in advanced high temperature coal combustion systems such as coal gasification and clean-up, coal fired gas turbines, and high efficiency heat engines. The objective of this research is to systematically evaluate the alkali corrosion resistance of the most commonly used structural ceramics including silicon carbide, silicon nitride, cordierite, mullite, alumina, aluminum titanate, zirconia, and fireclay glass. The study consists of identification of the alkali reaction products (phase equilibria) and the kinetics of the alkali reactions as a function of temperature and time.

Pickrell, G.R.; Sun, T.; Brown, J.J.

1992-05-27T23:59:59.000Z

191

Method for high temperature mercury capture from gas streams  

DOE Patents [OSTI]

A process to facilitate mercury extraction from high temperature flue/fuel gas via the use of metal sorbents which capture mercury at ambient and high temperatures. The spent sorbents can be regenerated after exposure to mercury. The metal sorbents can be used as pure metals (or combinations of metals) or dispersed on an inert support to increase surface area per gram of metal sorbent. Iridium and ruthenium are effective for mercury removal from flue and smelter gases. Palladium and platinum are effective for mercury removal from fuel gas (syngas). An iridium-platinum alloy is suitable for metal capture in many industrial effluent gas streams including highly corrosive gas streams.

Granite, E.J.; Pennline, H.W.

2006-04-25T23:59:59.000Z

192

Vibration Combined High Temperature Cycle Tests for Capacitive MEMS Accelerometers  

E-Print Network [OSTI]

In this paper vibration combined high temperature cycle tests for packaged capacitive SOI-MEMS accelerometers are presented. The aim of these tests is to provide useful Design for Reliability information for MEMS designers. A high temperature test chamber and a chopper-stabilized read-out circuitry were designed and realized at BME - DED. Twenty thermal cycles of combined Temperature Cycle Test and Fatigue Vibration Test has been carried out on 5 samples. Statistical evaluation of the test results showed that degradation has started in 3 out of the 5 samples.

Z. Szucs; G. Nagy; S. Hodossy; M. Rencz; A. Poppe

2008-01-07T23:59:59.000Z

193

Modular Pebble Bed Reactor High Temperature Gas Reactor  

E-Print Network [OSTI]

Modular Pebble Bed Reactor High Temperature Gas Reactor Andrew C Kadak Massachusetts Institute For 1150 MW Combined Heat and Power Station Oil Refinery Hydrogen Production Desalinization Plant VHTR/Graphite Discrimination system Damaged Sphere ContainerGraphiteReturn FuelReturn Fresh Fuel Container Spent Fuel Tank #12

194

Titanium dioxide based high temperature carbon monoxide selective sensor  

E-Print Network [OSTI]

Titanium dioxide based high temperature carbon monoxide selective sensor Nancy O. Savagea , Sheikh as a trap for the oxidation products of CO and CH4. Upon oxidation of CO on ALC, carbonate species were detected, whereas the reaction of CH4 produced negligible carbonate species. The insensitivity of the ALC

Dutta, Prabir K.

195

Free energy of Lorentz-violating QED at high temperature  

E-Print Network [OSTI]

In this paper we study the one- and two-loop contribution to the free energy in QED with the Lorentz symmetry breaking introduced via constant CPT-even Lorentz-breaking parameters at the high temperature limit. We find the impact of the Lorentz-violating term for the free energy and carry out a numerical estimation for the Lorentz-breaking parameter.

M. Gomes; T. Mariz; J. R. Nascimento; A. Yu. Petrov; A. F. Santos; A. J. da Silva

2009-10-23T23:59:59.000Z

196

Free energy of Lorentz-violating QED at high temperature  

Science Journals Connector (OSTI)

In this paper we study the one- and two-loop contribution to the free energy in QED with Lorentz symmetry breaking introduced via constant CPT-even Lorentz-breaking parameters at the high temperature limit. We find the impact of the Lorentz-violating term for the free energy and carry out a numerical estimation for the Lorentz-breaking parameter.

M. Gomes; T. Mariz; J. R. Nascimento; A. Yu. Petrov; A. F. Santos; A. J. da Silva

2010-02-17T23:59:59.000Z

197

High Temperature coatings based on {beta}-NiAI  

SciTech Connect (OSTI)

High temperature alloys are reviewed, focusing on current superalloys and their coatings. The synthesis, characerization, and oxidation performance of a NiAl–TiB{sub 2} composite are explained. A novel coating process for Mo–Ni–Al alloys for improved oxidation performance is examined. The cyclic oxidation performance of coated and uncoated Mo–Ni–Al alloys is discussed.

Severs, Kevin

2012-07-10T23:59:59.000Z

198

High Temperature and Pressure reactive flows through porous media.  

E-Print Network [OSTI]

of Ceramic Matrix Composite (CMC), used as high temperature material for combustion chamber or stagnation and chemical composition (Gas Chromatograph, Mass Spectrometer, Infra-Red spectrometer) in stationary and transient conditions. The tests on metallic and composite samples have been conducted with N2, CH4, H2+CH4

Boyer, Edmond

199

High-Temperature Gas-Stream Cleanup Test Facility  

SciTech Connect (OSTI)

In support of METC`s hot-gas filter development program, the high- temperature, gas-stream cleanup test facility was designed to: investigate conventional and novel approaches to high-temperature filtration; conduct detailed parametric studies that characterize particulate control devices under well-controlled conditions; and screen new materials for other high-temperature applications, such as heat exchanger tubes. This new facility utilizes a natural gas-fueled combustor to produce high-temperature process gas, and a screw feeder to inject ash, or other fine media, into the gas stream. The vessel that surrounds the particulate control devices has an inside diameter of roughly 0.20 meters (8 inches) and is about 3 meters (10 feet) long. Three commercial-size filter elements can be tested simultaneously, and the facility is capable of operating over a wide range of conditions. Operating temperatures can vary from 540 to 870{degrees}C (1,000 to 1,600 {degrees}F), and the operating pressure can vary from 0 to 400 kPa (0 to 60 psig).

Straub, D.; Chiang, Ta-Kuan, Schultz, J.

1996-12-31T23:59:59.000Z

200

Long, Highly-Ordered High-Temperature Superconductor Nanowire Arrays  

Science Journals Connector (OSTI)

Long, Highly-Ordered High-Temperature Superconductor Nanowire Arrays ... For bulk superconductors, the electrical resistance drops precipitously to zero below the superconducting transition temperature (Tc). ... Even these temperatures are considerably higher than those found in conventional superconductor NWs of similar widths, which are typically below liquid helium temperature (4.2 K). ...

Ke Xu; James R. Heath

2008-10-28T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Impurity effects on electronmode coupling in high-temperature superconductors  

E-Print Network [OSTI]

LETTERS Impurity effects on electron­mode coupling in high-temperature superconductors K. TERASHIMA espite years of intensive research on copper oxide superconductors with high transition temperatures (Tc in the high-Tc superconductors. The interaction of electrons with bosonic excitations (phonons or spin

Loss, Daniel

202

Sulfonated Polybenzimidazoles for High Temperature PEM Fuel Cells  

Science Journals Connector (OSTI)

Sulfonated Polybenzimidazoles for High Temperature PEM Fuel Cells ... An optimization series of polymerizations with final polymer concentrations from 2.5 to 6.0 wt % was conducted and the inherent viscosity of each polymer was measured. ... The membrane with an optimized compn. ...

Jordan A. Mader; Brian C. Benicewicz

2010-07-28T23:59:59.000Z

203

High Temperature Oxidation of Iron-Chromium Alloys  

E-Print Network [OSTI]

and Peter H. Larsen for many good discussions during the work. #12;3 Abstract The high temperature oxidation: References: Abstract (max. 2000 char.): See page 3 Information Service Department RisĂž National Laboratory P of Southern Denmark. The majority of the work is based on studies performed at the SOFC group at the Materials

204

FATIGUE AND FRACTURE BEHAVIOR OF HIGH TEMPERATURE MATERIALS  

E-Print Network [OSTI]

of damagetolerance in Ti3SiC,; (above the "ductile-brittle" transition temperature), where in fact, the plastic behavior in general is unusual for carbides and significant high-temperature deformation and damage are first is believed to be due to its layered structure and the metallic apparent. Of the two

Ritchie, Robert

205

High temperature, permanent magnet biased, homopolar magnetic bearing actuator  

E-Print Network [OSTI]

current resistance and improves the system efficiency because the magnetic field of the HTPM can suspend the major portion of the static load on bearing. A high temperature radial magnetic bearing was designed via an iterative search employing 3D finite...

Hossain, Mohammad Ahsan

2006-10-30T23:59:59.000Z

206

Refueling Liquid-Salt-Cooled Very High-Temperature Reactors  

SciTech Connect (OSTI)

The liquid-salt-cooled very high-temperature reactor (LS-VHTR), also called the Advanced High-Temperature Reactor (AHTR), is a new reactor concept that combines in a novel way four established technologies: (1) coated-particle graphite-matrix nuclear fuels, (2) Brayton power cycles, (3) passive safety systems and plant designs previously developed for liquid-metal-cooled fast reactors, and (4) low-pressure liquid-salt coolants. Depending upon goals, the peak coolant operating temperatures are between 700 and 1000 deg. C, with reactor outputs between 2400 and 4000 MW(t). Several fluoride salt coolants that are being evaluated have melting points between 350 and 500 deg. C, values that imply minimum refueling temperatures between 400 and 550 deg. C. At operating conditions, the liquid salts are transparent and have physical properties similar to those of water. A series of refueling studies have been initiated to (1) confirm the viability of refueling, (2) define methods for safe rapid refueling, and (3) aid the selection of the preferred AHTR design. Three reactor cores with different fuel element designs (prismatic, pebble bed, and pin-type fuel assembly) are being evaluated. Each is a liquid-salt-cooled variant of a graphite-moderated high-temperature reactor. The refueling studies examined applicable refueling experience from high-temperature reactors (similar fuel element designs) and sodium-cooled fast reactors (similar plant design with liquid coolant, high temperatures, and low pressures). The findings indicate that refueling is viable, and several approaches have been identified. The study results are described in this paper. (authors)

Forsberg, Charles W. [Oak Ridge National Laboratory, P.O. Box 2008 Oak Ridge, TN 37831 (United States); Peterson, Per F. [Nuclear Engineering Department, University of California at Berkeley, 6124a Etcheverry Hall, Berkeley, CA 94720 (United States); Cahalan, James E. [Argonne National Laboratory, 9700 S. Cass Avenue, Argonne, IL 60439 (United States); Enneking, Jeffrey A. [Areva NP (United States); Phil MacDonald [Consultant, Cedar Hill, TX (United States)

2006-07-01T23:59:59.000Z

207

CARISMA: A Networking Project for High Temperature PEMFC MEA Activities in Europe  

Broader source: Energy.gov [DOE]

This presentation on high temperature proton exchange membrane fuel cells was given at the High Temperature Membrane Working Group Meeting in May 2007.

208

Universal Membrane Classification Scheme: Maximizing the Return on High Temperature PEM Membrane Research  

Broader source: Energy.gov [DOE]

This presentation on maximizing the return of high temperature PEM membrane research was given at the High Temperature Membrane Working Group Meeting in May 2007.

209

HIGH TEMPERATURE CONDUCTIVITY PROBE FOR MONITORING CONTAMINATION LEVELS IN POWER PLANT BOILER WATER.  

E-Print Network [OSTI]

??A high temperature/high pressure flow through probe was designed to measure high temperature electrical conductivity of aqueous (aq) dilute electrolyte solutions, an application which can… (more)

Hipple, Sarah

2008-01-01T23:59:59.000Z

210

A Discussion of Conductivity Testing in High Temperature Membranes (lessons learned in assessing transport)  

Broader source: Energy.gov [DOE]

Presentation on conductivity testing in high temperature membranes given by Jim Boncella of Los Alamos National Laboratory at the High Temperature Membrane Working Group meeting in October 2005.

211

Contact resistance measurements recorded at conductive polymer/high-temperature superconductor interfaces  

Science Journals Connector (OSTI)

Contact resistance measurements recorded at conductive polymer/high-temperature superconductor interfaces ... Structure of the Electrical Double Layer in High-Temperature Superconductors. ...

Steven G. Haupt; David R. Riley; Jianai Zhao; John T. McDevitt

1993-01-01T23:59:59.000Z

212

High-Temperature Zirconia Oxygen Sensor with Sealed Metal/Metal...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

High-Temperature Zirconia Oxygen Sensor with Sealed MetalMetal Oxide Internal Reference High-Temperature Zirconia Oxygen Sensor with Sealed MetalMetal Oxide Internal Reference...

213

High-Temperature Motor Windings for Downhole Pumps Used in Geothermal...  

Broader source: Energy.gov (indexed) [DOE]

High-Temperature Motor Windings for Downhole Pumps Used in Geothermal Energy Production High-Temperature Motor Windings for Downhole Pumps Used in Geothermal Energy Production...

214

Two Phase Transitions Make a High-Temperature Superconductor  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Two Phase Transitions Make a High-Temperature Superconductor Print Two Phase Transitions Make a High-Temperature Superconductor Print Superconductivity-conceptually remarkable and practically revolutionary-is a quantum phenomenon in which bound electron pairs flow through a material in perfect synchrony, without friction. Conventional superconducting materials reach this state via a single thermal phase transition at a critical temperature (Tc). It was generally believed that such a picture also applied to the copper oxide (cuprate) superconductors-first discovered 25 years ago and the current record holders for highest Tc. However, three groups of researchers who performed measurements on the same cuprate material recently joined forces to prove that this view is inaccurate. Their work showed that another phase transition actually exists at a higher temperature in the cuprate phase diagram, below which electrons, instead of pairing up, organize themselves in a drastically different way.

215

Two Phase Transitions Make a High-Temperature Superconductor  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Two Phase Transitions Make a High-Temperature Superconductor Print Two Phase Transitions Make a High-Temperature Superconductor Print Superconductivity-conceptually remarkable and practically revolutionary-is a quantum phenomenon in which bound electron pairs flow through a material in perfect synchrony, without friction. Conventional superconducting materials reach this state via a single thermal phase transition at a critical temperature (Tc). It was generally believed that such a picture also applied to the copper oxide (cuprate) superconductors-first discovered 25 years ago and the current record holders for highest Tc. However, three groups of researchers who performed measurements on the same cuprate material recently joined forces to prove that this view is inaccurate. Their work showed that another phase transition actually exists at a higher temperature in the cuprate phase diagram, below which electrons, instead of pairing up, organize themselves in a drastically different way.

216

Two Phase Transitions Make a High-Temperature Superconductor  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Two Phase Transitions Make a High-Temperature Superconductor Print Two Phase Transitions Make a High-Temperature Superconductor Print Superconductivity-conceptually remarkable and practically revolutionary-is a quantum phenomenon in which bound electron pairs flow through a material in perfect synchrony, without friction. Conventional superconducting materials reach this state via a single thermal phase transition at a critical temperature (Tc). It was generally believed that such a picture also applied to the copper oxide (cuprate) superconductors-first discovered 25 years ago and the current record holders for highest Tc. However, three groups of researchers who performed measurements on the same cuprate material recently joined forces to prove that this view is inaccurate. Their work showed that another phase transition actually exists at a higher temperature in the cuprate phase diagram, below which electrons, instead of pairing up, organize themselves in a drastically different way.

217

Safeguards Guidance for Prismatic Fueled High Temperature Gas Reactors (HTGR)  

National Nuclear Security Administration (NNSA)

5) 5) August 2012 Guidance for High Temperature Gas Reactors (HTGRs) with Prismatic Fuel INL/CON-12-26130 Revision 0 Safeguards-by-Design: Guidance for High Temperature Gas Reactors (HTGRs) With Prismatic Fuel Philip Casey Durst (INL Consultant) August 2012 DISCLAIMER This information was prepared as an account of work sponsored by an agency of the U.S. Government. Neither the U.S. Government nor any agency thereof, nor any of their employees, makes any warranty, expressed or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness, of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. References herein to any specific commercial product,

218

Two Phase Transitions Make a High-Temperature Superconductor  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Two Phase Transitions Make a High-Temperature Superconductor Print Two Phase Transitions Make a High-Temperature Superconductor Print Superconductivity-conceptually remarkable and practically revolutionary-is a quantum phenomenon in which bound electron pairs flow through a material in perfect synchrony, without friction. Conventional superconducting materials reach this state via a single thermal phase transition at a critical temperature (Tc). It was generally believed that such a picture also applied to the copper oxide (cuprate) superconductors-first discovered 25 years ago and the current record holders for highest Tc. However, three groups of researchers who performed measurements on the same cuprate material recently joined forces to prove that this view is inaccurate. Their work showed that another phase transition actually exists at a higher temperature in the cuprate phase diagram, below which electrons, instead of pairing up, organize themselves in a drastically different way.

219

Safety philosophy of gas turbine high temperature reactor (GTHTR300)  

SciTech Connect (OSTI)

Japan Atomic Energy Research Institute (JAERI) has undertaken the study of an original design concept of gas turbine high temperature reactor, the GTHTR300. The general concept of this study is development of a greatly simplified design that leads to substantially reduced technical and cost requirements. Newly proposed design features enable the GTHTR300 to be an efficient and economically competitive reactor in 2010's. Also, the GTHTR300 fully takes advantage of its inherent safety characteristics. The safety philosophy of the GTHTR300 is developed based on the HTTR (High Temperature Engineering Test Reactor) of JAERI which is the first HTGR in Japan. Major features of the newly proposed safety philosophy for the GTHTR300 are described in this article. (authors)

Shoji Katanishi; Kazuhiko Kunitomi; Shusaku Shiozawa [Department of Advanced Nuclear Heat Technology, Oarai Research Institute, Japan Atomic Energy Research Institute, Oarai-machi, Ibaraki-ken, 311-1394 (Japan)

2002-07-01T23:59:59.000Z

220

Liquid Fuel Production from Biomass via High Temperature Steam Electrolysis  

SciTech Connect (OSTI)

A process model of syngas production using high temperature electrolysis and biomass gasification is presented. Process heat from the biomass gasifier is used to heat steam for the hydrogen production via the high temperature steam electrolysis process. Hydrogen from electrolysis allows a high utilization of the biomass carbon for syngas production. Oxygen produced form the electrolysis process is used to control the oxidation rate in the oxygen-fed biomass gasifier. Based on the gasifier temperature, 94% to 95% of the carbon in the biomass becomes carbon monoxide in the syngas (carbon monoxide and hydrogen). Assuming the thermal efficiency of the power cycle for electricity generation is 50%, (as expected from GEN IV nuclear reactors), the syngas production efficiency ranges from 70% to 73% as the gasifier temperature decreases from 1900 K to 1500 K. Parametric studies of system pressure, biomass moisture content and low temperature alkaline electrolysis are also presented.

Grant L. Hawkes; Michael G. McKellar

2009-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Materials Degradation Studies for High Temperature Steam Electrolysis Systems  

SciTech Connect (OSTI)

Experiments are currently in progress to assess the high temperature degradation behavior of materials in solid oxide electrolysis systems. This research includes the investigation of various electrolysis cell components and balance of plant materials under both anodic and cathodic gas atmospheres at temperatures up to 850°C. Current results include corrosion data for a high temperature nickel alloy used for the air-side flow field in electrolysis cells and a commercial ferritic stainless steel used as the metallic interconnect. Three different corrosion inhibiting coatings were also tested on the steel material. The samples were tested at 850șC for 500 h in both air and H2O/H2 atmospheres. The results of this research will be used to identify degradation mechanisms and demonstrate the suitability of candidate materials for long-term operation in electrolysis cells.

Paul Demkowicz; Pavel Medvedev; Kevin DeWall; Paul Lessing

2007-06-01T23:59:59.000Z

222

Quench development in a high temperature superconducting tape  

SciTech Connect (OSTI)

Normal zone propagation experiments have been performed on a long length of Bi-2223/Ag high temperature superconducting (HTS) tape. Tests were conducted with liquid nitrogen and gaseous helium cooling in temperatures from 5 to 77 K. No sustained expansion of a {open_quotes}normal{close_quotes} zone was observed with a short resistive heater. Non-uniform critical currents were, however, observed over the length of the conductor. When the conductor was charged and held at a current above the critical currents of weaker sections, a quench was being developed without distinctive {open_quotes}normal{close_quotes} zone propagation. Because of the high temperature margin and broad resistive transition of the superconductor, and the good thermal conductivity of the Ag-matrix, the quench process was very slow. and no large temperature gradient along the conductor was observed.

Lue, J.W.; Lubell, M.S. [Oak Ridge National Lab., TN (United States); Aized, D.; Campbell, J.M.; Schwall, R.E. [American Superconductor Corporation, Westborough, MA (United States)

1996-12-31T23:59:59.000Z

223

Quench development in a high temperature superconducting tape  

SciTech Connect (OSTI)

Normal zone propagation experiments have been per-formed on a long length of Bi2223/Ag high temperature superconducting (HTS) tape. Tests were performed in liquid nitrogen and with gaseous helium cooling in temperatures ranging from 4.2 K to 77 K. No sustained expansion of a ``normal`` zone was observed with a short resistive heater. Non-uniform critical currents were, however, observed over the length of the conductor. When the conductor was charged and held at a current above the critical currents of weaker sections, a quench was being developed without distinctive ``normal`` zone propagation. Because of the high temperature margin and broad resistive transition of the superconductor, and the good thermal conductivity of the Ag-matrix, the quench process was very slow, and no large temperature gradient along the conductor was observed in the test duration of a few minutes.

Lue, J.W.; Lubell, M.S. [Argonne National Lab., IL (United States); Aized, D.; Campbell, J.M.; Schwall, R.E. [American Superconductor Corp., Westborough, MA (United States)

1995-12-01T23:59:59.000Z

224

High-temperature phases of SrRuO3  

Science Journals Connector (OSTI)

The crystal structure of SrRuO3 at high temperatures has been studied using powder neutron diffraction and the Rietveld method. It was determined that from 300 K to approximately 820 K the structure of SrRuO3 is orthorhombic (Pbnm). The material then undergoes a phase transition and becomes tetragonal (I4/mcm) between ?820 and 920 K. The high-temperature (>920 K) structure was found to be the standard cubic perovskite (Pm3m). From the neutron-diffraction data and the space group assignments, the orthorhombic to tetragonal phase transition must be first order, while the transition from the tetragonal to cubic phase is consistent with a second-order phase transition.

Brendan J. Kennedy and Brett A. Hunter

1998-07-01T23:59:59.000Z

225

NETL: Mercury Emissions Control Technologies - Enhanced High Temperature  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Enhanced High Temperature Mercury Oxidation and Enhanced High Temperature Mercury Oxidation and In-Situ Active Carbon Generation for Low Cost Mercury Capture Mercury oxidation phenomenon and the studies of this phenomenon have generally focused on lower temperatures, typically below 650°F. This has been based on the mercury vapor equilibrium speciation curve. The baseline extents of mercury oxidation as reported in the ICR dataset and observed during subsequent tests has shown a tremendous amount of scatter. The objective of this project is to examine, establish and demonstrate the effect of higher temperature kinetics on mercury oxidation rates. Further, it is the objective of this project to demonstrate how the inherent mercury oxidation kinetics can be influenced to dramatically increase the mercury oxidation.

226

High Temperature Syngas Cleanup Technology Scale-up  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

RECOVERY ACT: Scale-Up of RECOVERY ACT: Scale-Up of High-Temperature Syngas Cleanup Technology Background Coal gasification generates a synthesis gas (syngas)-predominantly a mixture of carbon monoxide (CO) and hydrogen (H 2 )-that can be used for chemical production of hydrogen, methanol, substitute natural gas (SNG), and many other industrial chemicals, or for electric power generation. Conventional integrated gasification combined cycle (IGCC) power plants use this syngas as a fuel for a combustion

227

Adaptable Sensor Packaging for High Temperature Fossil Fuel Energy System  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Adaptable Sensor Packaging for High Adaptable Sensor Packaging for High Temperature Fossil Fuel Energy Systems Background The Advanced Research Sensors and Controls Program is leading the effort to develop sensing and control technologies and methods to achieve automated and optimized intelligent power systems. The program is led by the U.S. Department of Energy (DOE) Office of Fossil Energy National Energy Technology Laboratory (NETL) and is implemented through research and development agreements with other

228

Amorphous Alloy Membranes for High Temperature Hydrogen Separations  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

for High for High Temperature Hydrogen Separations Background Coal and biomass are readily available in the United States and can be mixed for thermal processing to produce hydrogen and power. The produced hydrogen can be sent directly to a fuel cell for highly efficient and environmentally clean power generation. For coal and biomass to become economically viable sources of hydrogen, more efficient production processes need to be developed. To meet this

229

A simple figure of merit for high temperature superconducting switches  

SciTech Connect (OSTI)

The discovery of the new high temperature superconductors has revived interest in many special applications, including superconducting switches. For comparison of switch types, a simple figure of merit based in switch performance is proposed, derived for superconducting switches, and then calculated for thyristors and vacuum switches. The figure of merit is then used to show what critical current density would be needed for superconducting switches to compete with more conventional switches. 46 refs., 1 fig.

Honig, E.M.

1989-01-01T23:59:59.000Z

230

Deposition method for producing silicon carbide high-temperature semiconductors  

DOE Patents [OSTI]

An improved deposition method for producing silicon carbide high-temperature semiconductor material comprising placing a semiconductor substrate composed of silicon carbide in a fluidized bed silicon carbide deposition reactor, fluidizing the bed particles by hydrogen gas in a mildly bubbling mode through a gas distributor and heating the substrate at temperatures around 1200.degree.-1500.degree. C. thereby depositing a layer of silicon carbide on the semiconductor substrate.

Hsu, George C. (La Crescenta, CA); Rohatgi, Naresh K. (W. Corine, CA)

1987-01-01T23:59:59.000Z

231

Silicide-matrix materials for high-temperature applications  

SciTech Connect (OSTI)

Intermetallic-matrix composites are attractive alternatives to carbon/carbon and ceramic/ceramic composities for applications up to 1,600 C. Recent work on the intermetallic compounds MoSi2 and Ti5Si3 has included determination of their mechanical properties and deformation behavior, selection of thermodynamically compatible high-strength and ductile reinforcements, and strengthening and toughening mechanisms in silicide-matrix composites for high-temperature service. 11 refs.

Meschter, P.J.; Schwartz, D.S. (McDonnell Douglas Research Laboratories, Saint Louis, MO (USA))

1989-11-01T23:59:59.000Z

232

Sealed glass coating of high temperature ceramic superconductors  

DOE Patents [OSTI]

A method and article of manufacture of a lead oxide based glass coating on a high temperature superconductor. The method includes preparing a dispersion of glass powders in a solution, applying the dispersion to the superconductor, drying the dispersion before applying another coating and heating the glass powder dispersion at temperatures below oxygen diffusion onset and above the glass melting point to form a continuous glass coating on the superconductor to establish compressive stresses which enhance the fracture strength of the superconductor.

Wu, Weite (Tainan, TW); Chu, Cha Y. (Garnerville, NY); Goretta, Kenneth C. (Downers Grove, IL); Routbort, Jules L. (Darien, IL)

1995-01-01T23:59:59.000Z

233

Protective interlayer for high temperature solid electrolyte electrochemical cells  

DOE Patents [OSTI]

A high temperature, solid electrolyte electrochemical cell is made, having a first and second electrode with solid electrolyte between them, where the electrolyte is formed by hot chemical vapor deposition, where a solid, interlayer material, which is electrically conductive, oxygen permeable, and protective of electrode material from hot metal halide vapor attack, is placed between the first electrode and the electrolyte, to protect the first electrode from the hot metal halide vapors during vapor deposition.

Isenberg, Arnold O. (Forest Hills Boro, PA); Ruka, Roswell J. (Churchill Boro, PA)

1986-01-01T23:59:59.000Z

234

Protective interlayer for high temperature solid electrolyte electrochemical cells  

DOE Patents [OSTI]

A high temperature, solid electrolyte electrochemical cell is made, having a first and second electrode with solid electrolyte between them, where the electrolyte is formed by hot chemical vapor deposition, where a solid, interlayer material, which is electrically conductive, oxygen permeable, and protective of electrode material from hot metal halide vapor attack, is placed between the first electrode and the electrolyte, to protect the first electrode from the hot metal halide vapors during vapor deposition.

Isenberg, Arnold O. (Forest Hills Boro, PA); Ruka, Roswell J. (Churchill Boro, PA); Zymboly, Gregory E. (Penn Hills Township, Allegheny County, PA)

1985-01-01T23:59:59.000Z

235

Protective interlayer for high temperature solid electrolyte electrochemical cells  

DOE Patents [OSTI]

A high temperature, solid electrolyte electrochemical cell is made, having a first and second electrode with solid electrolyte between them, where the electrolyte is formed by hot chemical vapor deposition, where a solid, interlayer material, which is electrically conductive, oxygen permeable, and protective of electrode material from hot metal halide vapor attack, is placed between the first electrode and the electrolyte, to protect the first electrode from the hot metal halide vapors during vapor deposition.

Isenberg, Arnold O. (Forest Hills Boro, PA); Ruka, Roswell J. (Churchill Boro, PA)

1987-01-01T23:59:59.000Z

236

Nuclear matter at high temperature and low net baryonic density  

SciTech Connect (OSTI)

We study the effect of the {sigma}-{omega} mesons interaction on nucleon-antinucleon matter properties. This interaction is employed in the context of the linear Walecka model to discuss the behavior of this system at high temperature and low net baryonic density regime. The field equations are solved in the relativistic mean-field approximation and our results show that the phase transition pointed out in the literature for this regime is eliminated when the meson interaction are considered.

Costa, R. S.; Duarte, S. B. [Centro Brasileiro de Pesquisas Fisicas-CBPF, Rua Dr. Xavier Sigaud, 150 Urca 22290-180, Rio de Janeiro, RJ (Brazil); Oliveira, J. C. T. [Departamento de Fisica, Universidade Federal de Roraima, Campus do Paricarana, s/n, 69310-270, Boa Vista, RR (Brazil); Rodrigues, H. [Centro Federal de Educacao Tecnologica do Rio de Janeiro, Av. Maracana, 249 Maracana 20271-110, Rio de Janeiro, RJ (Brazil); Chiapparini, M. [Instituto de Fisica, Universidade do Estado do Rio de Janeiro, Rua Sao Francisco Xavier, 524 Maracana, Rio de Janeiro, RJ (Brazil)

2010-11-12T23:59:59.000Z

237

High Temperature, High Pressure Devices for Zonal Isolation in Geothermal  

Open Energy Info (EERE)

Temperature, High Pressure Devices for Zonal Isolation in Geothermal Temperature, High Pressure Devices for Zonal Isolation in Geothermal Wells Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title High Temperature, High Pressure Devices for Zonal Isolation in Geothermal Wells Project Type / Topic 1 Recovery Act: Enhanced Geothermal Systems Component Research and Development/Analysis Project Type / Topic 2 Zonal Isolation Project Description For Enhanced Geothermal Systems (EGS), high-temperature high-pressure zonal isolation tools capable of withstanding the downhole environment are needed. In these wells the packers must withstand differential pressures of 5,000 psi at more than 300°C, as well as pressures up to 20,000 psi at 200°C to 250°C. Furthermore, when deployed these packers and zonal isolation tools must form a reliable seal that eliminates fluid loss and mitigates short circuiting of flow from injectors to producers. At this time, general purpose open-hole packers do not exist for use in geothermal environments, with the primary technical limitation being the poor stability of existing elastomeric seals at high temperatures.

238

Particle-hole symmetry broken pseudogap in high temperature superconductors  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Particle-hole symmetry broken pseudogap in Particle-hole symmetry broken pseudogap in high temperature superconductors High-temperature (Tc) superconductivity is one of the most important topics in condensed matter physics. Despite extensive studies over more than two decades, the microscopic mechanism of high temperature superconductivity still remains elusive due to many unconventional properties that are not well understood. Among them, the most mysterious behavior of high-Tc superconductor is the nature of so called "pseudogap", which has been a focus of the field for many years. In conventional superconductors, a gap exists in the energy absorption spectrum only below Tc, corresponding to the energy price to pay for breaking a Cooper pair of electrons. In high-Tc cuprate superconductors, an energy gap called the pseudogap exists above Tc but below T*, and is controversially attributed either to pre-formed superconducting pairs or to competing phases. Recently, by carefully studying the "symmetry" of the gap, researchers Makoto Hashimoto and Rui-Hua He, along with their co-workers in Prof. Zhi-Xun Shen's group at Stanford University, have found crucial evidence suggesting that the particle-hole symmetry required by superconductivity is broken in the pseudogap state.

239

High-Temperature-High-Volume Lifting For Enhanced Geothermal Systems  

Open Energy Info (EERE)

Temperature-High-Volume Lifting For Enhanced Geothermal Systems Temperature-High-Volume Lifting For Enhanced Geothermal Systems Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title High-Temperature-High-Volume Lifting For Enhanced Geothermal Systems Project Type / Topic 1 Recovery Act: Enhanced Geothermal Systems Component Research and Development/Analysis Project Type / Topic 2 High-Temperature-High-Volume Lifting Project Description The proposed scope of work is divided into three Phases. Overall system requirements will be established in Phase 1, along with an evaluation of existing lifting system capability, identification of technology limitations, and a conceptual design of an overall lifting system. In developing the system components in Phase 2, component-level tests will be conducted using GE facilities. Areas of development will include high-temperature drive system materials, journal and thrust bearings, and corrosion and erosion-resistant lifting pump components. Finally, in Phase 3, the overall lab-scale lifting system will be demonstrated in a flow loop that will be constructed at GE Global Research.

240

Pseudogap and Superconducting Gap in High-Temperature Superconductors  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Pseudogap and Superconducting Gap in Pseudogap and Superconducting Gap in High-Temperature Superconductors Two decades after the discovery of first high temperature superconductors, the microscopic mechanism of high-Tc superconductivity remains elusive. In conventional superconductors, it has been well established that electrons form so-called "Cooper pairs" to give rise to superconductivity. The pair binding manifests itself as an energy gap in many spectroscopic measurements. This energy gap, known as superconducting gap, appears at the superconducting transition temperature Tc where the resistance also vanishes. For high temperature superconductors, the story is more complicated. Over a wide region of compositions and temperatures, there exists an energy gap well above Tc. This energy gap is called pseudogap [1], because there is no direct correlation to the superconducting transition. The origin of this pseudogap and its relation to the superconducting gap are believed to hold the key for understanding the mechanism of high-Tc superconductivity - one of the outstanding problems in condensed matter physics. In this regard, researchers Kiyohisa Tanaka and Wei-Sheng Lee, along with their co-workers in Prof. Zhi-Xun Shen's group at Stanford University, have recently made an important discovery about the coexistence of two distinct energy gaps that have opposite doping dependence. Their observation not only provides a natural explanation for the contradictory results about the superconducting gap deduced from different experimental techniques, but also has profound implications on the mechanism of high-Tc superconductivity.

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Selection of materials for high temperature sensible energy storage  

Science Journals Connector (OSTI)

Abstract Availability of thermal energy storage systems (TES) is a key to ensuring continuous power supply from solar thermal power plants. The application of sensible heat storage (SHS) in solid media is an attractive economic option, but is dependent on identifying suitable SHS media. Given the growing number of new materials available today, finding a suitable material is a time-consuming and difficult process. This paper demonstrates the use of a materials selection software package and identifies suitable SHS materials for high temperature (>500 °C) TES systems. The environmental performance of some selected materials was also evaluated using the package. Common materials such as alumina, silicon carbide, high temperature concrete, graphite, cast iron and steel were found to be highly suitable for SHS for the duty considered (500–750 °C). For cost comparison, a simple heat exchanger, consisting of a packed bed of the materials (in brick or block form) heated by an inert gas, was considered. On the basis of equivalent gas phase heat transfer, high alumina cement concrete blocks had the lowest cost, followed by a common refractory brick at High temperature concretes, such as the high alumina cement-based materials and alumina–silicate geoploymers, were identified as having potential for SHS media as they are cheap composite materials. Their thermo–physical properties could be optimised for SHS by a suitable choice of aggregates, binders and additives.

S. Khare; M. Dell'Amico; C. Knight; S. McGarry

2013-01-01T23:59:59.000Z

242

Note: Zeeman splitting measurements in a high-temperature plasma  

SciTech Connect (OSTI)

The Zeeman effect has been used for measurement of magnetic fields in low-temperature plasma, but the diagnostic technique is difficult to implement in a high-temperature plasma. This paper describes new instrumentation and methodology for simultaneous measurement of the entire Doppler-broadened left and right circularly polarized Zeeman spectra in high-temperature plasmas. Measurements are made using spectra emitted parallel to the magnetic field by carbon impurities in high-temperature plasma. The Doppler-broadened width is much larger than the magnitude of the Zeeman splitting, thus simultaneous recording of the two circularly polarized Zeeman line profiles is key to accurate measurement of the magnetic field in the ZaP Z-pinch plasma device. Spectral data are collected along multiple chords on both sides of the symmetry axis of the plasma. This enables determination of the location of the current axis of the Z-pinch and of lower-bound estimates of the local magnetic field at specific radial locations in the plasma.

Golingo, R. P.; Shumlak, U.; Den Hartog, D. J. [Aerospace and Energetics Research Program, University of Washington, Seattle, Washington 98195-2250 (United States)

2010-12-15T23:59:59.000Z

243

Minutes of the October 2008 Meeting of the High Temperature Membrane Working Group  

Broader source: Energy.gov [DOE]

Meeting minutes of the High Temperature Membrane Working Group from October 16, 2008, in Honolulu, Hawaii.

244

R&D Plan for the High Temperature Membrane Working Group  

Broader source: Energy.gov [DOE]

Summary of challenges, approaches and technical targets for HFCIT's High Temperature Membrane Working Group.

245

Thermomechanical Characterization of a TiPdNi High Temperature SMA under Tension  

E-Print Network [OSTI]

Electrode Discharge Machining (EDM). A high temperature experimental setup was developed on a load frame

246

11th Topical conference high-temperature plasma diagnostics. Book of abstracts  

SciTech Connect (OSTI)

This report contains abstracts from the 11th topical conference on high-temperature plasma diagnostics.

NONE

1996-06-01T23:59:59.000Z

247

Spectroscopy and kinetics of combustion gases at high temperatures  

SciTech Connect (OSTI)

This program involves two complementary activities: (1) development and application of cw ring dye laser absorption methods for sensitive detection of radical species and measurement of fundamental spectroscopic parameters at high temperatures; and (2) shock tube studies of reaction kinetics relevant to combustion. Species currently under investigation in the spectroscopic portion of the research include NO and CH{sub 3}; this has necessitated the continued operated at wavelengths in the range 210-230 nm. Shock tube studies of reaction kinetics currently are focussed on reactions involving CH{sub 3} radicals.

Hanson, R.K.; Bowman, C.T. [Stanford Univ., CA (United States)

1993-12-01T23:59:59.000Z

248

High temperature gas cooled reactor steam-methane reformer design  

SciTech Connect (OSTI)

The concept of the long distance transportation of process heat energy from a High Temperature Gas Cooled Reactor (HTGR) heat source, based on the steam-methane reforming reaction, is being evaluated by the Department of Energy as an energy source/application for use early in the 21st century. This paper summaries the design of a helium heated steam reformer utilized in conjunction with an intermediate loop, 850/degree/C reactor outlet temperature, HTGR process heat plant concept. This paper also discusses various design considerations leading to the mechanical design features, the thermochemical performance, the materials selection and the structural design analysis. 12 refs.

Impellezzeri, J.R.; Drendel, D.B.; Odegaard, T.K.

1981-01-01T23:59:59.000Z

249

NOVEL CERAMIC MEMBRANE FOR HIGH TEMPERATURE CARBON DIOXIDE SEPARATION  

SciTech Connect (OSTI)

This project is aimed at demonstrating technical feasibility for a lithium zirconate based dense ceramic membrane for separation of carbon dioxide from flue gas at high temperature. The research work conducted in this reporting period was focused on several fundamental issues of lithium zirconate important to the development of the dense inorganic membrane. These fundamental issues include material synthesis of lithium zirconate, phases and microstructure of lithium zirconate and structure change of lithium zirconate during sorption/desorption process. The results show difficulty to prepare the dense ceramic membrane from pure lithium zirconate, but indicate a possibility to prepare the dense inorganic membrane for carbon dioxide separation from a composite lithium zirconate.

Jerry Y.S. Lin; Jun-ichi Ida

2001-03-01T23:59:59.000Z

250

Resonant Spin Excitation in an Overdoped High Temperature Superconductor  

Science Journals Connector (OSTI)

An inelastic neutron scattering study of overdoped Bi2Sr2CaCu2O8+? ( Tc=83K) has revealed a resonant spin excitation in the superconducting state. The mode energy is Eres=38.0meV, significantly lower than in optimally doped Bi2Sr2CaCu2O8+? ( Tc=91K, Eres=42.4meV). This observation, which indicates a constant ratio Eres/kBTc?5.4, helps resolve a long-standing controversy about the origin of the resonant spin excitation in high temperature superconductors.

H. He; Y. Sidis; P. Bourges; G. D. Gu; A. Ivanov; N. Koshizuka; B. Liang; C. T. Lin; L. P. Regnault; E. Schoenherr; B. Keimer

2001-02-19T23:59:59.000Z

251

Confinement of Spin and Charge in High-Temperature Superconductors  

E-Print Network [OSTI]

By exploiting the internal gauge-invariance intrinsic to a spin-charge separated electron, we show that such degrees of freedom must be confined in two-dimensional superconductors experiencing strong inter-electron repulsion. We also demonstrate that incipient confinement in the normal state can prevent chiral spin-fluctuations from destroying the cross-over between strange and psuedo-gap regimes in under-doped high-temperature superconductors. Last, we suggest that the negative Hall anomaly observed in these materials is connected with this confinement effect.

J. P. Rodriguez; Pascal Lederer

1996-04-17T23:59:59.000Z

252

Nearly Perfect Fluidity in a High Temperature Superconductor  

E-Print Network [OSTI]

Perfect fluids are characterized as having the smallest ratio of shear viscosity to entropy density, {\\eta}/s, consistent with quantum uncertainty and causality. So far, nearly perfect fluids have only been observed in the Quark-Gluon Plasma (QGP) and in unitary atomic Fermi gases (UFG), exotic systems that are amongst the hottest and coldest objects in the known universe, respectively. We use Angle Resolve Photoemission Spectroscopy (ARPES) to measure the temperature dependence of an electronic analogue of {\\eta}/s in an optimally doped cuprate high temperature superconductor, finding it too is a nearly perfect fluid around, and above, its superconducting transition temperature Tc.

J. D. Rameau; T. J. Reber; H. -B. Yang; S. Akhanjee; G. D. Gu; S. Campbell; P. D. Johnson

2014-09-19T23:59:59.000Z

253

Nearly Perfect Fluidity in a High Temperature Superconductor  

E-Print Network [OSTI]

Perfect fluids are characterized as having the smallest ratio of shear viscosity to entropy density, {\\eta}/s, consistent with quantum uncertainty and causality. So far, nearly perfect fluids have only been observed in the Quark-Gluon Plasma (QGP) and in unitary atomic Fermi gases (UFG), exotic systems that are amongst the hottest and coldest objects in the known universe, respectively. We use Angle Resolve Photoemission Spectroscopy (ARPES) to measure the temperature dependence of an electronic analogue of {\\eta}/s in an optimally doped cuprate high temperature superconductor, finding it too is a nearly perfect fluid around, and above, its superconducting transition temperature Tc.

Rameau, J D; Yang, H -B; Akhanjee, S; Gu, G D; Campbell, S; Johnson, P D

2014-01-01T23:59:59.000Z

254

Nearly perfect fluidity in a high-temperature superconductor  

Science Journals Connector (OSTI)

Perfect fluids are characterized as having the smallest ratio of shear viscosity to entropy density, ?/s, consistent with quantum uncertainty and causality. So far, nearly perfect fluids have only been observed in the quark-gluon plasma and in unitary atomic Fermi gases, exotic systems that are amongst the hottest and coldest objects in the known universe, respectively. We use angle resolved photoemission spectroscopy to measure the temperature dependence of an electronic analog of ?/s in an optimally doped cuprate high-temperature superconductor, finding it too is a nearly perfect fluid around, and above, its superconducting transition temperature Tc.

J. D. Rameau; T. J. Reber; H.-B. Yang; S. Akhanjee; G. D. Gu; P. D. Johnson; S. Campbell

2014-10-13T23:59:59.000Z

255

Sealed glass coating of high temperature ceramic superconductors  

DOE Patents [OSTI]

A method and article of manufacture of a lead oxide based glass coating on a high temperature superconductor is disclosed. The method includes preparing a dispersion of glass powders in a solution, applying the dispersion to the superconductor, drying the dispersion before applying another coating and heating the glass powder dispersion at temperatures below oxygen diffusion onset and above the glass melting point to form a continuous glass coating on the superconductor to establish compressive stresses which enhance the fracture strength of the superconductor. 8 figs.

Wu, W.; Chu, C.Y.; Goretta, K.C.; Routbort, J.L.

1995-05-02T23:59:59.000Z

256

Ohmic contacts for high-temperature GaP devices  

E-Print Network [OSTI]

REMOVAL 10 13 24 24 26 50 50 52 78 80 83 98 98 99 100 TABLE OF CONTENTS (Continued) APPENDIX D ? 6 LIFT-OFF PREMETAL PREPARATION APPENDIX D ? 7 METAL LIFTOFF Page 100 100 vi LIST OP TABLES Table I Relative High Temperature... with a variety of III-V compound semi- conductors and contact metals. By using a ruby or a COe laser with Au-Sn or Ag-Sn contact metals, specific contact resistances as low as 8. 6 x 19 " 0-cm were reported. (The specific contact resistance...

Van der Hoeven, Willem Bernard

2012-06-07T23:59:59.000Z

257

High temperature chemistry of advanced heavy water reactor fuel  

Science Journals Connector (OSTI)

The Department of Atomic Energy envisages the use of thoria based fuel in the third phase of nuclear power generation. The fuel will consist of solid solution of thorium-uranium and thorium-plutonium in the form of their oxides. The former will contain 2.5 mole % UO2 while the latter about 4 mole % PuO2. Since no other country in the world has used such fuel, no data is available on its behavior under long-term irradiation. The high temperature chemistry of fuel can however provide some insight into the behavior of such fuel during irradiation and could be of considerable help in the assessment of its long-term integrity. The high temperature chemistry of the fuel essentially involves the measurement of thermodynamic properties of the compounds formed in the multi-component systems comprising the fuel matrix, the fission products and the clad. The physical integrity of the fuel under long-term irradiation can be predicted with the help of basic thermodynamic data such as the Gibbs energy of formation of various compounds and their thermophysical properties such as thermal conductivity and coefficient of thermal expansion derived from experimental measurements. The paper highlights the measurements made on some typical systems relevant to the prediction of thoria based fuel behaviour during long-term irradiation. The experimental problems faced in such measurements are also discussed.

S.R. Dharwadkar

2002-01-01T23:59:59.000Z

258

High temperature thermometric phosphors for use in a temperature sensor  

DOE Patents [OSTI]

A high temperature phosphor consists essentially of a material having the general formula LuPO.sub.4 :Dy.sub.(x),Eu.sub.(y), wherein: 0.1 wt %.ltoreq.x.ltoreq.20 wt % and 0.1 wt %.ltoreq.y.ltoreq.20 wt %. The high temperature phosphor is in contact with an article whose temperature is to be determined. The article having the phosphor in contact with it is placed in the environment for which the temperature of the article is to be determined. The phosphor is excited by a laser causing the phosphor to fluoresce. The emission from the phosphor is optically focused into a beam-splitting mirror which separates the emission into two separate emissions, the emission caused by the dysprosium dopant and the emission caused by the europium dopent. The separated emissions are optically filtered and the intensities of the emission are detected and measured. The ratio of the intensity of each emission is determined and the temperature of the article is calculated from the ratio of the intensities of the separate emissions.

Allison, Stephen W. (Knoxville, TN); Cates, Michael R. (Oak Ridge, TN); Boatner, Lynn A. (Oak Ridge, TN); Gillies, George T. (Earlysville, VA)

1998-01-01T23:59:59.000Z

259

Baseline Concept Description of a Small Modular High Temperature Reactor  

SciTech Connect (OSTI)

The objective of this report is to provide a description of generic small modular high temperature reactors (herein denoted as an smHTR), summarize their distinguishing attributes, and lay out the research and development (R&D) required for commercialization. The generic concepts rely heavily on the modular high temperature gas-cooled reactor designs developed in the 1980s which were never built but for which pre-licensing or certification activities were conducted. The concept matured more recently under the Next Generation Nuclear Plant (NGNP) project, specifically in the areas of fuel and material qualification, methods development, and licensing. As all vendor-specific designs proposed under NGNP were all both ‘small’ or medium-sized and ‘modular’ by International Atomic Energy Agency (IAEA) and Department of Energy (DOE) standards, the technical attributes, challenges, and R&D needs identified, addressed, and documented under NGNP are valid and appropriate in the context of Small Modular Reactor (SMR) applications. Although the term High Temperature Reactor (HTR) is commonly used to denote graphite-moderated, thermal spectrum reactors with coolant temperatures in excess of 650oC at the core outlet, in this report the historical term High Temperature Gas-Cooled Reactor (HTGR) will be used to distinguish the gas-cooled technology described herein from its liquid salt-cooled cousin. Moreover, in this report it is to be understood that the outlet temperature of the helium in an HTGR has an upper limit of 950 degrees C which corresponds to the temperature to which certain alloys are currently being qualified under DOE’s ARC program. Although similar to the HTGR in just about every respect, the Very High Temperature Reactor (VHTR) may have an outlet temperature in excess of 950 degrees C and is therefore farther from commercialization because of the challenges posed to materials exposed to these temperatures. The VHTR is the focus of R&D under the Generation IV program and its specific R&D needs will be included in this report when appropriate for comparison. The distinguishing features of the HTGR are the refractory (TRISO) coated particle fuel, the low-power density, graphite-moderated core, and the high outlet temperature of the inert helium coolant. The low power density and fuel form effectively eliminate the possibility of core melt, even upon a complete loss of coolant pressure and flow. The graphite, which constitutes the bulk of the core volume and mass, provides a large thermal buffer that absorbs fission heat such that thermal transients occur over a timespan of hours or even days. As chemically-inert helium is already a gas, there is no coolant temperature or void feedback on the neutronics and no phase change or corrosion product that could degrade heat transfer. Furthermore, the particle coatings and interstitial graphite retain fission products such that the source terms at the plant boundary remain well below actionable levels under all anticipated nominal and off-normal operating conditions. These attributes enable the reactor to supply process heat to a collocated industrial plant with negligible risk of contamination and minimal dynamic coupling of the facilities (Figure 1). The exceptional retentive properties of coated particle fuel in a graphite matrix were first demonstrated in the DRAGON reactor, a European research facility that began operation in 1964.

Hans Gougar

2014-05-01T23:59:59.000Z

260

High temperature corrosion research at the Albany Research Center  

SciTech Connect (OSTI)

The Severe Environment Corrosion and Erosion Research Facility (SECERF) at the Albany Research Center is operational. SECERF consists of 6 modules that share the availability of up to 10 different gases to produce environments for high temperature corrosion and erosion research. Projects to be conducted in the modules include: corrosion sensors for fossil energy systems, thermal gradient effects on high temperature corrosion, the development of sulfidation resistant alloys, determination of the effects of ash on the corrosion of metals and alloys in coal and waste combustion and coal gasification environments, high temperature erosion-corrosion of metals, and molten slag effects on refractories. Results from two areas, the effect of ash deposits on alloy corrosion and thermal gradient effects on the corrosion of metals, will be highlighted. Ash produced in coal gasifiers, coal combustors, and waste combustors, when deposited on metal surfaces, provides sites for corrosion attack and contributes chemical species that participate in the corrosion reaction. Results are presented for the corrosion of 304L stainless steel, that was either uncoated or coated with ash or with ash containing NaCl or Na2SO4, in air-water vapor mixtures at 600 C. The presence of high heat fluxes and temperature gradients in many fossil energy systems creates the need for an understanding of their effects on corrosion and oxidation. Such information would be useful for both improved alloy design and for better translation of isothermal laboratory results to field use. Temperature gradients in a solid oxide result in two changes that modify diffusion within the oxide. The first is when a gradient in point defect concentration is created within the oxide, for example, where more vacancies are expected at a higher temperature. The second change is when the presence of a temperature gradient biases the diffusion jump of an atom. Results of tests are presented for cobalt with metal surface temperatures of approximately 920-950 C in N2 plus 1-10 vol% O2 environments with a heat flux of about 40 kW/m2. Non-equilibrium thermodynamics were used to develop oxidation rate equations in temperature gradients that were combined with point defect information of CoO to predict oxidation rates.

Covino, Bernard S., Jr.; Holcomb, Gordon R.; Russell, James H.; Cramer, Stephen D.; Bullard, Sophie J.; Ziomek-Moroz, Margaret; Matthes, Steven A.; Chinn, R.E.

2002-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

NETL: Gasification - Recovery Act: High Temperature Syngas Cleanup  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Syngas Processing Systems Syngas Processing Systems Recovery Act: High Temperature Syngas Cleanup Technology Scale-Up and Demonstration Project Research Triangle Institute Project Number: FE0000489 Project Description Research Triangle Institute (RTI) is designing, building, and testing the Warm Temperature Desulfurization Process (WDP) at pre-commercial scale (50 megawatt electric equivalent [MWe]) to remove more than 99.9 percent of the sulfur from coal-derived synthesis gas (syngas). RTI is integrating this WDP technology with an activated methyl diethanolamine (aMDEA) solvent technology to separate 90% of the carbon dioxide (CO2) from shifted syngas. The Polk Power Station, an integrated gasification combined cycle (IGCC) power plant, will supply approximately 20% of its coal-derived syngas as a slipstream to feed into the pre-commercial scale technologies being scaled-up.

262

Microsoft PowerPoint - High Temperature Thermoelectric_Ohuchi  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Thermoelectric Oxides Engineered Thermoelectric Oxides Engineered at Multiple Length Scales for Energy Harvesting Program Manager: Patricia Rawls Fumio S. Ohuchi (PI) and Rajendra K. Bordia(Co-PI) Department of Materials Science and Engineering University of Washington Box 352120 Seattle, WA 98195 Grant No. DE-FE0007272 (June 1, 2012-May 31, 2013) Graduate Students: Christopher Dandeneau and YiHsun Yang June 10, 2013 The UCR Contractors Review Conference Introduction/Motivation for Research * Thermoelectric (TE) oxides for waste heat recovery  Good high-temperature stability  Stable in hostile environments  Low cost/toxicity * Oxides with complex structure:  Low thermal conductivity,   Tailor stoichiometry to maximize S

263

NOVEL REFRACTORY MATERIALS FOR HIGH ALKALI, HIGH TEMPERATURE ENVIRONMENTS  

SciTech Connect (OSTI)

Refractory materials can be limited in their application by many factors including chemical reactions between the service environment and the refractory material, mechanical degradation of the refractory material by the service environment, temperature limitations on the use of a particular refractory material, and the inability to install or repair the refractory material in a cost effective manner or while the vessel was in service. The objective of this project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al 2O3 spinel or other similar magnesia/alumina containing unshaped refractory composition (castables, gunnables, shotcretes, etc) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, high-alkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries.

Hemrick, James Gordon [ORNL

2011-09-01T23:59:59.000Z

264

Apparatus and method for high temperature viscosity and temperature measurements  

DOE Patents [OSTI]

A probe for measuring the viscosity and/or temperature of high temperature liquids, such as molten metals, glass and similar materials comprises a rod which is an acoustical waveguide through which a transducer emits an ultrasonic signal through one end of the probe, and which is reflected from (a) a notch or slit or an interface between two materials of the probe and (b) from the other end of the probe which is in contact with the hot liquid or hot melt, and is detected by the same transducer at the signal emission end. To avoid the harmful effects of introducing a thermally conductive heat sink into the melt, the probe is made of relatively thermally insulative (non-heat-conductive) refractory material. The time between signal emission and reflection, and the amplitude of reflections, are compared against calibration curves to obtain temperature and viscosity values.

Balasubramaniam, Krishnan (Mississippi State, MS); Shah, Vimal (Houston, TX); Costley, R. Daniel (Mississippi State, MS); Singh, Jagdish P. (Mississippi State, MS)

2001-01-01T23:59:59.000Z

265

Fluoride Salt-Cooled High-Temperature Reactor Development Roadmap  

SciTech Connect (OSTI)

Fluoride salt-cooled high-temperature reactors (FHRs) are an emerging reactor class with potentially advantageous performance characteristics and fully passive safety. This paper provides an overview of a technology development pathway for expeditious commercial deployment of first-generation FHRs. The paper describes the principal remaining FHR technology challenges and the development path needed to address the challenges. First-generation FHRs do not appear to require any technology breakthroughs, but will require significant technology development and demonstration. FHRs are currently entering early phase engineering development. As such, the development roadmap is not as technically detailed or specific as would be the case for a more mature reactor class. The higher cost of fuel and coolant; the lack of an approved licensing framework; the lack of qualified, salt-compatible structural materials; and the potential for tritium release into the environment are the most obvious issues that remain to be resolved.

Holcomb, David Eugene [ORNL] [ORNL; Flanagan, George F [ORNL] [ORNL; Mays, Gary T [ORNL] [ORNL; Pointer, William David [ORNL] [ORNL; Robb, Kevin R [ORNL] [ORNL; Yoder Jr, Graydon L [ORNL] [ORNL

2014-01-01T23:59:59.000Z

266

9 Cr-- 1 Mo steel material for high temperature application  

DOE Patents [OSTI]

One or more embodiments relates to a high-temperature, titanium alloyed, 9 Cr-1 Mo steel exhibiting improved creep strength and oxidation resistance at service temperatures up to 650.degree. C. The 9 Cr-1 Mo steel has a tempered martensite microstructure and is comprised of both large (0.5-3 .mu.m) primary titanium carbides and small (5-50 nm) secondary titanium carbides in a ratio of. from about 1:1.5 to about 1.5:1. The 9 Cr-1 Mo steel may be fabricated using exemplary austenizing, rapid cooling, and tempering steps without subsequent hot working requirements. The 9 Cr-1 Mo steel exhibits improvements in total mass gain, yield strength, and time-to-rupture over ASTM P91 and ASTM P92 at the temperature and time conditions examined.

Jablonski, Paul D; Alman, David; Dogan, Omer; Holcomb, Gordon; Cowen, Christopher

2012-11-27T23:59:59.000Z

267

High Temperature Chemical Kinetic Combustion Modeling of Lightly Methylated Alkanes  

SciTech Connect (OSTI)

Conventional petroleum jet and diesel fuels, as well as alternative Fischer-Tropsch (FT) fuels and hydrotreated renewable jet (HRJ) fuels, contain high molecular weight lightly branched alkanes (i.e., methylalkanes) and straight chain alkanes (n-alkanes). Improving the combustion of these fuels in practical applications requires a fundamental understanding of large hydrocarbon combustion chemistry. This research project presents a detailed high temperature chemical kinetic mechanism for n-octane and three lightly branched isomers octane (i.e., 2-methylheptane, 3-methylheptane, and 2,5-dimethylhexane). The model is validated against experimental data from a variety of fundamental combustion devices. This new model is used to show how the location and number of methyl branches affects fuel reactivity including laminar flame speed and species formation.

Sarathy, S M; Westbrook, C K; Pitz, W J; Mehl, M

2011-03-01T23:59:59.000Z

268

Steam reformers heated by helium from high temperature reactors  

Science Journals Connector (OSTI)

The manifold possibilities of the application of helium-heated steam reformers combined with high temperature nuclear reactors are elucidated in this article. It is shown that the thermodynamic interpretation of the processes does not cause difficulties because of the good heat transfer in helium at high pressure and that helium peak temperatures of 950°C are sufficient for carrying out the process. The mechanical design of the reformer tube does not lead to problems because the helium and process pressures are so chosen as to be approximately equal. The problems of hydrogen and tritium permeation as well as the contamination of the reformer tube with solid fission products seem to be solvable using the knowledge available at present. Furthermore, the various possibilities for the design arrangements of helium-heated reformer tube furnaces are shown. The status of development attained to date is outlined and in conclusion there is a survey regarding the next steps to be taken in steam reformer technology.

K. Kugeler; M. Kugeler; H.F. Niessen; K.H. Hammelmann

1975-01-01T23:59:59.000Z

269

Dust accelerators and their applications in high-temperature plasmas  

SciTech Connect (OSTI)

The perennial presence of dust in high-temperature plasma and fusion devices has been firmly established. Dust inventory must be controlled, in particular in the next-generation steady-state fusion machines like ITER, as it can pose significant safety hazards and potentially interfere with fusion energy production. Much effort has been devoted to gening rid of the dust nuisance. We have recognized a number of dust-accelerators applications in magnetic fusion, including in plasma diagnostics, in studying dust-plasma interactions, and more recently in edge localized mode (ELM)'s pacing. With the applications in mind, we will compare various acceleration methods, including electrostatic, gas-drag, and plasma-drag acceleration. We will also describe laboratory experiments and results on dust acceleration.

Wang, Zhehui [Los Alamos National Laboratory; Ticos, Catakin M [NILPRP, ROMANIA

2010-01-01T23:59:59.000Z

270

Acoustic studies of single?crystal high?temperature superconductors  

Science Journals Connector (OSTI)

The acoustic properties of single crystals of the high?temperature superconductor YBa 2 Cu 3 O 7 have been measured at temperatures between 0.1 and 300 K for frequencies near 103 and 109 Hz. In the GHz regime longitudinal modes have been studied for propagation directions parallel and perpendicular to the c axis. At Tc there is a discontinuity in the soundvelocities and their temperature derivatives from which the anisotropic strain dependences of Tc are obtained. In the kHz regime resonant excitation of flexural modes in thin reeds of YBa 2 Cu 3 O 7 crystals has permitted precise measurement of acoustic damping and dispersion. The temperature?dependent damping is characterized by at least five features associated with the relaxation of defects. At temperatures below 1 K the velocity of sound is consistent with the presence of a broad “glasslike” distribution of tunneling modes.

Brage Golding; W. H. Haemmerle; L. F. Schneemeyer

1988-01-01T23:59:59.000Z

271

Acoustic microscopy for characterization of high?temperature superconducting tape  

Science Journals Connector (OSTI)

Although material scientists constantly discover superconducting compounds with higher critical temperatures (T c ’s) manufacturing of the high?temperature superconductors(HTS) remains a problem and long lengths (>1 mile) have yet to be produced. In an effort to produce long length superconductors manufacturing steps for HTS tape production have been critically looked at to find their effects in producing tape with the desired characteristics. In support of determining superconducting tapecharacteristics acoustic microscopy offers the potential for internal microstructural material characterization. This research will ultimately support in?process monitoring of HTSmanufacturing as part of an advanced sensing system to determine the presence of defects and/or the effects of process variables on the HTS tape. This presentation will overview scanning acoustic microscopy and present images of HTS tape at several frequencies ranging from 50 to 500 MHz. The results clearly demonstrate the feasibility of determining the Ag/ceramic interface location and the general integrity of the constituents.

Chiaki Miyasaka; Chris Cobucci; Bernhard Tittmann

1997-01-01T23:59:59.000Z

272

Potential impact of high temperature superconductors on maglev transportation  

SciTech Connect (OSTI)

This report describes the potential impact that high-temperature superconductors (HTSs) may have on transportation by magnetically levitated vehicles. It is not intended as a planning document, but rather as an overview of potential HTS applications to magnetic-levitation (maglev) transportation. The present maglev program in the United States is summarized, and the present status of development of HTSs is described. Areas identified for possible impact on maglev technology are (1) liquid-nitrogen-cooled levitation magnets, (2) magnetic-field shielding of the passenger compartment, (3) superconducting magnetic energy storage for wayside power, (4) superconducting bearings for flywheel energy storage for wayside power, (5) downleads to continuously powered liquid-helium-cooled levitation magnets, and (6) liquid-hydrogen-cooled levitation magnets and linear motor propulsion windings. Major technical issues that remain to be resolved for the use of HTSs in maglev applications include thermal magnetic stability, mechanical properties, and critical current density at liquid-nitrogen temperatures.

Hull, J.R.

1992-02-01T23:59:59.000Z

273

Factors affecting characterization of bulk high-temperature superconductors  

SciTech Connect (OSTI)

Three major factors affect the characterization of bulk high-temperature superconductors in terms of their levitation properties during interaction with permanent magnets. First, the appropriate parameter for the permanent magnet is internal magnetization, not the value of the magnetic field measured at the magnet`s surface. Second, although levitation force grows with superconductor thickness and surface area, for a given permanent magnet size, comparison of levitation force between samples is meaningful when minimum values are assigned to the superconductor size parameters. Finally, the effect of force creep must be considered when time-averaging the force measurements. In addition to levitational force, the coefficient of friction of a levitated rotating permanent magnet may be used to characterize the superconductor.

Hull, J.R. [Argonne National Lab., IL (United States). Energy Technology Div.

1997-11-01T23:59:59.000Z

274

Anisotropic high temperature superconductors as variable resistors and switches  

SciTech Connect (OSTI)

Several anisotropic high temperature superconductors show critical current densities which are strongly dependent on the direction of an applied external magnetic field. The resistance of a sample can change by several orders of magnitude by applying a magnetic field. The potential for using the field dependent variable resistor or switch for applications in power systems is evaluated. Test results with small samples are presented. The requirements for large scale applications are outlined. The magnetic field triggering requirement, the frequency response of the device, use in 60 Hz ac circuits and heat transfer consideration are investigated. Several application examples are discussed. Use of variable resistor as a fault current limiter, as a switching element in rectifier circuitry and as an improved dump resistor for a superconducting magnet is presented.

Boenig, H.J.; Daugherty, M.A.; Fleshler, S.; Maley, M.P.; Mueller, F.M.; Prenger, F.C.; Coulter, J.Y.

1994-12-01T23:59:59.000Z

275

Shock-induced synthesis of high temperature superconducting materials  

DOE Patents [OSTI]

It has now been determined that the unique features of the high pressure shock method, especially the shock-induced chemical synthesis technique, are fully applicable to high temperature superconducting materials. Extraordinarily high yields are achievable in accordance with this invention, e.g., generally in the range from about 20% to about 99%, often in the range from about 50% to about 90%, lower and higher yields, of course, also being possible. The method of this invention involves the application of a controlled high pressure shock compression pulse which can be produced in any conventional manner, e.g., by detonation of a high explosive material, the impact of a high speed projectile or the effect of intense pulsed radiation sources such as lasers or electron beams. Examples and a discussion are presented.

Ginley, D.S.; Graham, R.A.; Morosin, B.; Venturini, E.L.

1987-06-18T23:59:59.000Z

276

Spontaneous quenches of a high temperature superconducting pancake coil  

SciTech Connect (OSTI)

A double-pancake coil made of Bi-2223/Ag high temperature superconducting (HTS) tape was constructed with an embedded heater and graded conductors to study the stability and quench propagation in HTS coils. The experiments were performed with liquid nitrogen and gaseous helium cooling in temperatures ranging from 5 to 77 K. The coil was very stable, and no ``normal`` zone was sustained or propagated with local pulsed heating. However, spontaneous quenches of the cod were experienced. This was found to be the result of having the coil current higher than that of the lower I{sub c} sections of the coil for a long time. This quench process took minutes to develop--much longer than would be expected in a low temperature superconducting coil. The quench behaved more like a spreading and continuous heating of an increasingly larger partially resistive section of the coil than like a sequential ``normal`` front propagation.

Lue, J.W.; Lubell, M.S. [Oak Ridge National Lab., TN (United States); Aized, D.; Campbell, J.M.; Schwall, R.E. [American Superconductor Corp., Westborough, MA (United States)

1995-09-01T23:59:59.000Z

277

Spontaneous quenches of a high temperature superconducting pancake coil  

SciTech Connect (OSTI)

A double-pancake coil made of Bi-2223/Ag high temperature superconducting (HTS) tape was constructed with an embedded heater and graded conductors to study the stability and quench propagation in HTS coils. The experiments were performed with liquid nitrogen and gaseous helium cooling in temperatures ranging from 5 to 77 K. The coil was very stable, and no normal zone was sustained or propagated with local pulsed heating. However, spontaneous quenches of the coil were experienced. This was found to be the result of having the coil current higher than that of the lower I{sub c} sections of the coil for a long time. This quench process took minutes to develop--much longer than would be expected in a low temperature superconducting coil. The quench behaved more like a spreading and continuous heating of an increasingly larger partially resistive section of the coil than like a sequential normal front propagation.

Lue, J.W.; Lubell, M.S. [Oak Ridge National Lab., TN (United States)] [Oak Ridge National Lab., TN (United States); Aized, D.; Campbell, J.M.; Schwall, R.E. [American Superconductor Corp., Westborough, MA (United States)] [American Superconductor Corp., Westborough, MA (United States)

1996-07-01T23:59:59.000Z

278

Test of two prototype high-temperature superconducting transmission cables  

SciTech Connect (OSTI)

Two 500-A class prototype high-temperature superconducting cables have been constructed by Southwire Company and tested at Oak Ridge National Laboratory (ORNL). In the first cable, no insulation was used to separate the individual HTS tapes. In the second cable, Kapton tape was used to insulate the HTS tapes between successive layers for the study of AC loss and current distribution. The cables were tested with both DC and AC currents in liquid nitrogen from 77 to 69 K. Both cables achieved DC critical current, I{sub c} greater than 500 A. A calorimetric technique that measures the cable temperature rise under ac currents was used to measure the ac loss of the cables. The un-insulated cable showed a cryoresistive behavior under the 60 Hz AC currents. The insulated cable started to show measurable loss at current where there was corresponding resistive loss.

Lue, J.W.; Lubell, M.S.; Kroeger, D.M.; Martin, P.M. [Oak Ridge National Lab., TN (United States); Demko, J.A.; Jones, E.C. [Oak Ridge Associated Universities, Inc., TN (United States); Sinha, U.; Hughey, R.L. [Southwire Co., Carrollton, GA (United States)

1996-10-01T23:59:59.000Z

279

Overview of High-Temperature Electrolysis for Hydrogen Production  

SciTech Connect (OSTI)

Over the last five years there has been a growing interest in the use of hydrogen as an energy carrier, particularly to augment transportation fuels and thus reduce our dependence on imported petroleum. Hydrogen is now produced primarily via steam reforming of methane. However, in the long term, methane reforming is not a viable process for the large-scale hydrogen production since such fossil fuel conversion processes consume non-renewable resources and emit greenhouse gases. Nuclear energy can be used to produce hydrogen without consuming fossil fuels and without emitting greenhouse gases through the splitting of water into hydrogen and oxygen. The Nuclear Hydrogen Initiative of the DOE Office of Nuclear Energy is developing three general categories of high temperature processes for hydrogen production: thermochemical, electrolytic and hybrid thermo-electrolytic. This paper introduces the work being done in the development of high temperature electrolysis of steam. High Temperature Electrolysis (HTE) is built on the technology of solid oxide fuel cells (SOFCs), which were invented over a century ago, but which have been most vigorously developed during the last twenty years. SOFCs consume hydrogen and oxygen and produce steam and electricity. Solid Oxide Electrolytic Cells (SOECs) consume electricity and steam and produce hydrogen and oxygen. The purpose of the HTE research is to solve those problems unique to the electrolytic mode of operation, while building further on continuing fuel cell development. ORGANIZATION Experiments have been conducted for the last three years at the Idaho National Laboratory and at Ceramatec, Inc. on the operation of button cells and of progressively larger stacks of planar cells. In addition, the INL has been performing analyses of the cell-scale fluid dynamics and plant-scale flowsheets in order to determine optimum operating conditions and plant configurations. Argonne National Laboratory has been performing experiments for the development of new electrode materials, as well as modeling of the fluid dynamics and flowsheets for comparison with the work being done at the INL. ANL has also been performing diagnostic measures on components form long-duration tests at the INL and Ceramatec to determine the causes for the slow degradation in cell performance. Oak Ridge National Laboratory has been developing high temperature porous membranes for the separation of hydrogen from the residual steam, thus avoiding the need to condense and reheat the steam. The University of Nevada at Las Vegas has been collaborating with ANL on the development of electrode and electrolyte materials and will soon begin to investigate the causes of cell degradation. HTE research also includes NERI projects at the Virginia Polytechnic Institute on the development of toughened SOEC composite seals and at the Georgia Institute of Technology on the microstructural design of SOEC materials. EXPERIMENTAL RESULTS The most recent large-scale test of HTE was performed from June 28 through Sept 22, 2006 at the Ceramatec plant in Salt Lake City. The test apparatus consists of two stacks of 60 cells each in a configuration that will be used in the Integrated Laboratory Scale (ILS) experiment during FY-07. The ILS will contain three modules of four stacks each. The “Half-Module” initially produced 1.2 normal m3of H2/hour and 0.65 Nm3/hr at the end of the 2040-hour continuous test.

Herring, J. S.; O'Brien, J. E.; Stoots, C. M.; Hartvigsen, J. J.; Petri, M. C.; Carter, J. D.; Bischoff, B. L.

2007-06-01T23:59:59.000Z

280

Remote high-temperature insulatorless heat-flux gauge  

DOE Patents [OSTI]

A remote optical heat-flux gauge for use in extremely high temperature environments is described. This application is possible because of the use of thermographic phosphors as the sensing media, and the omission of the need for an intervening layer of insulator between phosphor layers. The gauge has no electrical leads, but is interrogated with ultraviolet or laser light. The luminescence emitted by the two phosphor layers, which is indicative of the temperature of the layers, is collected and analyzed in order to determine the heat flux incident on the surface being investigated. The two layers of thermographic phosphor must be of different materials to assure that the spectral lines collected will be distinguishable. Spatial heat-flux measurements can be made by scanning the light across the surface of the gauge. 3 figures.

Noel, B.W.

1993-12-28T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Remote high-temperature insulatorless heat-flux gauge  

DOE Patents [OSTI]

A remote optical heat-flux gauge for use in extremely high temperature environments is described. This application is possible because of the use of thermographic phosphors as the sensing media, and the omission of the need for an intervening layer of insulator between phosphor layers. The gauge has no electrical leads, but is interrogated with ultraviolet or laser light. The luminescence emitted by the two phosphor layers, which is indicative of the temperature of the layers, is collected and analyzed in order to determine the heat flux incident on the surface being investigated. The two layers of thermographic phosphor must be of different materials to assure that the spectral lines collected will be distinguishable. Spatial heat-flux measurements can be made by scanning the light across the surface of the gauge.

Noel, Bruce W. (Espanola, NM)

1993-01-01T23:59:59.000Z

282

High performance internal reforming unit for high temperature fuel cells  

DOE Patents [OSTI]

A fuel reformer having an enclosure with first and second opposing surfaces, a sidewall connecting the first and second opposing surfaces and an inlet port and an outlet port in the sidewall. A plate assembly supporting a catalyst and baffles are also disposed in the enclosure. A main baffle extends into the enclosure from a point of the sidewall between the inlet and outlet ports. The main baffle cooperates with the enclosure and the plate assembly to establish a path for the flow of fuel gas through the reformer from the inlet port to the outlet port. At least a first directing baffle extends in the enclosure from one of the sidewall and the main baffle and cooperates with the plate assembly and the enclosure to alter the gas flow path. Desired graded catalyst loading pattern has been defined for optimized thermal management for the internal reforming high temperature fuel cells so as to achieve high cell performance.

Ma, Zhiwen (Sandy Hook, CT); Venkataraman, Ramakrishnan (New Milford, CT); Novacco, Lawrence J. (Brookfield, CT)

2008-10-07T23:59:59.000Z

283

Applications of high-temperature superconductors in power technology  

Science Journals Connector (OSTI)

Since the discovery of the first high-temperature superconductors (HTSs) in the late 1980s, many materials and families of materials have been discovered that exhibit superconductivity at temperatures well above 20?K. Of these, several families of HTSs have been developed for use in electrical power applications. Demonstration of devices such as motors, generators, transmission lines, transformers, fault-current limiters, and flywheels in which HTSs and bulk HTSs have been used has proceeded to ever larger scales. First-generation wire, made from bismuth-based copper oxides, was used in many demonstrations. The rapid development of second-generation wire, made by depositing thin films of yttrium-based copper oxide on metallic substrates, is expected to further accelerate commercial applications. Bulk HTSs, in which large single-grain crystals are used as basic magnetic components, have also been developed and have potential for electrical power applications.

John R Hull

2003-01-01T23:59:59.000Z

284

Assessment of microelectronics packaging for high temperature, high reliability applications  

SciTech Connect (OSTI)

This report details characterization and development activities in electronic packaging for high temperature applications. This project was conducted through a Department of Energy sponsored Cooperative Research and Development Agreement between Sandia National Laboratories and General Motors. Even though the target application of this collaborative effort is an automotive electronic throttle control system which would be located in the engine compartment, results of this work are directly applicable to Sandia`s national security mission. The component count associated with the throttle control dictates the use of high density packaging not offered by conventional surface mount. An enabling packaging technology was selected and thermal models defined which characterized the thermal and mechanical response of the throttle control module. These models were used to optimize thick film multichip module design, characterize the thermal signatures of the electronic components inside the module, and to determine the temperature field and resulting thermal stresses under conditions that may be encountered during the operational life of the throttle control module. Because the need to use unpackaged devices limits the level of testing that can be performed either at the wafer level or as individual dice, an approach to assure a high level of reliability of the unpackaged components was formulated. Component assembly and interconnect technologies were also evaluated and characterized for high temperature applications. Electrical, mechanical and chemical characterizations of enabling die and component attach technologies were performed. Additionally, studies were conducted to assess the performance and reliability of gold and aluminum wire bonding to thick film conductor inks. Kinetic models were developed and validated to estimate wire bond reliability.

Uribe, F.

1997-04-01T23:59:59.000Z

285

High-temperature Hydrogen Permeation in Nickel Alloys  

SciTech Connect (OSTI)

In gas cooled Very High Temperature Reactor concepts, tritium is produced as a tertiary fission product and by activation of graphite core contaminants, such as lithium; of the helium isotope, He-3, that is naturally present in the He gas coolant; and the boron in the B4C burnable poison. Because of its high mobility at the reactor outlet temperatures, tritium poses a risk of permeating through the walls of the intermediate heat exchanger (IHX) or steam generator (SG) systems, potentially contaminating the environment and in particular the hydrogen product when the reactor heat is utilized in connection with a hydrogen generation plant. An experiment to measure tritium permeation in structural materials at temperatures up to 1000 C has been constructed at the Idaho National Laboratory Safety and Tritium Applied Research (STAR) facility within the Next Generation Nuclear Plant program. The design is based on two counter flowing helium loops to represent heat exchanger conditions and was optimized to allow control of the materials surface condition and the investigation of the effects of thermal fatigue. In the ongoing campaign three nickel alloys are being considered because of their high-temperature creep properties, alloy 617, 800H and 230. This paper introduces the general issues related to tritium in the on-going assessment of gas cooled VHTR systems fission product transport and outlines the planned research activities in this area; outlines the features and capabilities of the experimental facility being operated at INL; presents and discusses the initial results of hydrogen permeability measurements in two of the selected alloys and compares them with the available database from previous studies.

P. Calderoni; M. Ebner; R. Pawelko

2010-10-01T23:59:59.000Z

286

SunShot Initiative: High-Temperature Falling-Particle Receiver  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

High-Temperature Falling-Particle High-Temperature Falling-Particle Receiver to someone by E-mail Share SunShot Initiative: High-Temperature Falling-Particle Receiver on Facebook Tweet about SunShot Initiative: High-Temperature Falling-Particle Receiver on Twitter Bookmark SunShot Initiative: High-Temperature Falling-Particle Receiver on Google Bookmark SunShot Initiative: High-Temperature Falling-Particle Receiver on Delicious Rank SunShot Initiative: High-Temperature Falling-Particle Receiver on Digg Find More places to share SunShot Initiative: High-Temperature Falling-Particle Receiver on AddThis.com... Concentrating Solar Power Systems Components Competitive Awards CSP Research & Development Thermal Storage CSP Recovery Act Baseload CSP SunShot Multidisciplinary University Research Initiative

287

New Polymeric Proton Conductors for Water-free and High-temperature Fuel Cells  

Broader source: Energy.gov [DOE]

Presentation on New Polymeric Proton Conductors for Water-free and High-temperature Fuel Cells to the High Temperature Membrane Working Group Meeting held in Arlington, Virginia, May 26,2005.

288

The Role of PentaCoordinated Al3+ Ions in the High Temperature...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

PentaCoordinated Al3+ Ions in the High Temperature Phase Transformation of ?-Al2O3. The Role of PentaCoordinated Al3+ Ions in the High Temperature Phase Transformation of...

289

Sources of high temperature degradation of cement-based materials : nanoindentation and microporoelastic analysis  

E-Print Network [OSTI]

The effects of high temperature exposure on cement-based materials have been under investigation for quite some time, but a fundamental understanding of the sources of high temperature degradation has been limited by ...

DeJong, Matthew J. (Matthew Justin)

2005-01-01T23:59:59.000Z

290

High Temperature/Low Humidity Polymer Electrolytes Derived from Ionic Liquids  

Broader source: Energy.gov [DOE]

Presentation on High Temperature/Low Humidity Polymer Electrolytes Derived from Ionic Liquids to the High Temperature Membrane Working Group Meeting held in Arlington, Virginia, May 26,2005.

291

High Temperature, High Pressure Devices for Zonal Isolation in Geothermal Wells  

Broader source: Energy.gov [DOE]

DOE Geothermal Peer Review 2010 - Presentation. Project objectives: Design, demonstrate, and qualify high-temperature high pressure zonal isolation devices compatible with the high temperature downhole Enhanced Geothermal Systems (EGS) environment.

292

Dual Phase Membrane for High Temperature CO2 Separation  

SciTech Connect (OSTI)

This project aimed at synthesis of a new inorganic dual-phase carbonate membrane for high temperature CO{sub 2} separation. Metal-carbonate dual-phase membranes were prepared by the direct infiltration method and the synthesis conditions were optimized. Permeation tests for CO{sub 2} and N{sub 2} from 450-750 C showed very low permeances of those two gases through the dual-phase membrane, which was expected due to the lack of ionization of those two particular gases. Permeance of the CO{sub 2} and O{sub 2} mixture was much higher, indicating that the gases do form an ionic species, CO{sub 3}{sup 2-}, enhancing transport through the membrane. However, at temperatures in excess of 650 C, the permeance of CO{sub 3}{sup 2-} decreased rapidly, while predictions showed that permeance should have continued to increase with temperature. XRD data obtained from used membrane indicated that lithium iron oxides formed on the support surface. This lithium iron oxide layer has a very low conductivity, which drastically reduces the flow of electrons to the CO{sub 2}/O{sub 2} gas mixture; thus limiting the formation of the ionic species required for transport through the membrane. These results indicated that the use of stainless steel supports in a high temperature oxidative environment can lead to decreased performance of the membranes. This revelation created the need for an oxidation resistant support, which could be gained by the use of a ceramic-type membrane. Work was extended to synthesize a new inorganic dual-phase carbonate membrane for high temperature CO{sub 2} separation. Helium permeance of the support before and after infiltration of molten carbonate are on the order of 10{sup -6} and 10{sup -10} moles/m{sup 2} {center_dot} Pa {center_dot} s respectively, indicating that the molten carbonate is able to sufficiently infiltrate the membrane. It was found that La{sub 0.6}Sr{sub 0.4}Co{sub 0.8}Fe{sub 0.2}O{sub 3-{delta}} (LSCF) was a suitable candidate for the support material. This support material proved to separate CO{sub 2} when combined with O{sub 2} at a flux of 0.194 ml/min {center_dot} cm{sup 2} at 850 C. It was also observed that, because LSCF is a mixed conductor (conductor of both electrons and oxygen ions), the support was able to provide its own oxygen to facilitate separation of CO{sub 2}. Without feeding O{sub 2}, the LSCF dual phase membrane produced a maximum CO{sub 2} flux of 0.246 ml/min {center_dot} cm{sup 2} at 900 C.

Jerry Lin

2007-06-30T23:59:59.000Z

293

Performance and Reliability of Bonded Interfaces for High-Temperature Packaging (Presentation)  

SciTech Connect (OSTI)

This presentation reviews the status of the performance and reliability of bonded interfaces for high-temperature packaging.

Devoto, D.

2014-06-01T23:59:59.000Z

294

NREL Particle Receiver Will Enable High-Temperature CSP (Fact Sheet)  

SciTech Connect (OSTI)

Near-blackbody enclosed particle receiver can support high-temperature thermal energy storage and high-efficiency power cycles.

Not Available

2014-08-01T23:59:59.000Z

295

Membrane Development for Medium and High Temperature PEMFC in Europe (Presentation)  

Broader source: Energy.gov [DOE]

Presented at the High Temperature Membrane Working Group Meeting (HTMWG) held October 10, 2007 in Washington, D.C.

296

High-Temperature Air-Cooled Power Electronics Thermal Design (Presentation)  

SciTech Connect (OSTI)

This presentation discusses the status of research at NREL on high temperature air-cooled power electronics thermal design.

Waye, S.

2014-06-01T23:59:59.000Z

297

Effect of a constant magnetic field on echo signals in high-temperature superconductor powders  

Science Journals Connector (OSTI)

The generation of acoustic and vortex oscillations in high-temperature superconductor (HTSC) powders excited by radiofrequency (rf...

E. G. Apushkinskii; M. S. Astrov

2013-03-01T23:59:59.000Z

298

Low and high Temperature Dual Thermoelectric Generation Waste Heat Recovery System for Light-Duty Vehicles  

Broader source: Energy.gov [DOE]

Developing a low and high temperature dual thermoelectric generation waste heat recovery system for light-duty vehicles.

299

New Polymeric Proton Conductors for Water-free and High-temperature...  

Broader source: Energy.gov (indexed) [DOE]

for water-free and high temperature operation. - Measure conductivity, mechanicalthermal properties of Nafion and Polyether polyelectrolytes doped with imidazoles....

300

High-Temperature Circuit Boards for Use in Geothermal Well Monitoring Applications  

Broader source: Energy.gov [DOE]

Project objective: Develop and demonstrate high-temperature; multilayer electronic circuits capable of sustained operation at 300? C.

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

High Temperature Calcination - MACT Upgrade Equipment Pilot Plant Test  

SciTech Connect (OSTI)

About one million gallons of acidic, hazardous, and radioactive sodium-bearing waste are stored in stainless steel tanks at the Idaho Nuclear Technology and Engineering Center (INTEC), which is a major operating facility of the Idaho National Engineering and Environmental Laboratory. Calcination at high-temperature conditions (600 C, with alumina nitrate and calcium nitrate chemical addition to the feed) is one of four options currently being considered by the Department of Energy for treatment of the remaining tank wastes. If calcination is selected for future processing of the sodium-bearing waste, it will be necessary to install new off-gas control equipment in the New Waste Calcining Facility (NWCF) to comply with the Maximum Achievable Control Technology (MACT) standards for hazardous waste combustors and incinerators. This will require, as a minimum, installing a carbon bed to reduce mercury emissions from their current level of up to 7,500 to <45 {micro}g/dscm, and a staged combustor to reduce unburned kerosene fuel in the off-gas discharge to <100 ppm CO and <10 ppm hydrocarbons. The staged combustor will also reduce NOx concentrations of about 35,000 ppm by 90-95%. A pilot-plant calcination test was completed in a newly constructed 15-cm diameter calciner vessel. The pilot-plant facility was equipped with a prototype MACT off-gas control system, including a highly efficient cyclone separator and off-gas quench/venturi scrubber for particulate removal, a staged combustor for unburned hydrocarbon and NOx destruction, and a packed activated carbon bed for mercury removal and residual chloride capture. Pilot-plant testing was performed during a 50-hour system operability test January 14-16, followed by a 100-hour high-temperature calcination pilot-plant calcination run January 19-23. Two flowsheet blends were tested: a 50-hour test with an aluminum-to-alkali metal molar ratio (AAR) of 2.25, and a 50-hour test with an AAR of 1.75. Results of the testing indicate that sodium-bearing waste can be successfully calcined at 600 C with an AAR of 1.75. Unburned hydrocarbons are reduced to less than 10 ppm (7% O2, dry basis), with >90% reduction of NOx emissions. Mercury removal by the carbon bed reached 99.99%, surpassing the control efficiency needed to meet MACT emissions standards. No deleterious impacts on the carbon bed were observed during the tests. The test results imply that upgrading the NWCF calciner with a more efficient cyclone separator and the proposed MACT equipment can process the remaining tanks wastes in 3 years or less, and comply with the MACT standards.

Richard D. Boardman; B. H. O'Brien; N. R. Soelberg; S. O. Bates; R. A. Wood; C. St. Michel

2004-02-01T23:59:59.000Z

302

DEGRADATION ISSUES IN SOLID OXIDE CELLS DURING HIGH TEMPERATURE ELECTROLYSIS  

SciTech Connect (OSTI)

Idaho National Laboratory (INL) is performing high-temperature electrolysis research to generate hydrogen using solid oxide electrolysis cells (SOECs). The project goals are to address the technical and degradation issues associated with the SOECs. This paper provides a summary of various ongoing INL and INL sponsored activities aimed at addressing SOEC degradation. These activities include stack testing, post-test examination, degradation modeling, and a list of issues that need to be addressed in future. Major degradation issues relating to solid oxide fuel cells (SOFC) are relatively better understood than those for SOECs. Some of the degradation mechanisms in SOFCs include contact problems between adjacent cell components, microstructural deterioration (coarsening) of the porous electrodes, and blocking of the reaction sites within the electrodes. Contact problems include delamination of an electrode from the electrolyte, growth of a poorly (electronically) conducting oxide layer between the metallic interconnect plates and the electrodes, and lack of contact between the interconnect and the electrode. INL’s test results on high temperature electrolysis (HTE) using solid oxide cells do not provide a clear evidence whether different events lead to similar or drastically different electrochemical degradation mechanisms. Post-test examination of the solid oxide electrolysis cells showed that the hydrogen electrode and interconnect get partially oxidized and become non-conductive. This is most likely caused by the hydrogen stream composition and flow rate during cool down. The oxygen electrode side of the stacks seemed to be responsible for the observed degradation due to large areas of electrode delamination. Based on the oxygen electrode appearance, the degradation of these stacks was largely controlled by the oxygen electrode delamination rate. University of Utah (Virkar) has developed a SOEC model based on concepts in local thermodynamic equilibrium in systems otherwise in global thermodynamic non-equilibrium. This model is under continued development. It shows that electronic conduction through the electrolyte, however small, must be taken into account for determining local oxygen chemical potential, within the electrolyte. The chemical potential within the electrolyte may lie out of bounds in relation to values at the electrodes in the electrolyzer mode. Under certain conditions, high pressures can develop in the electrolyte just under the oxygen electrode (anode)/electrolyte interface, leading to electrode delamination. This theory is being further refined and tested by introducing some electronic conduction in the electrolyte.

J. E. O'Brien; C. M. Stoots; V. I. Sharma; B. Yildiz; A. V. Virkar

2010-06-01T23:59:59.000Z

303

DEGRADATION ISSUES IN SOLID OXIDE CELLS DURING HIGH TEMPERATURE ELECTROLYSIS  

SciTech Connect (OSTI)

Idaho National Laboratory (INL) is performing high-temperature electrolysis research to generate hydrogen using solid oxide electrolysis cells (SOECs). The project goals are to address the technical and degradation issues associated with the SOECs. This paper provides a summary of various ongoing INL and INL sponsored activities aimed at addressing SOEC degradation. These activities include stack testing, post-test examination, degradation modeling, and a list of issues that need to be addressed in future. Major degradation issues relating to solid oxide fuel cells (SOFC) are relatively better understood than those for SOECs. Some of the degradation mechanisms in SOFCs include contact problems between adjacent cell components, microstructural deterioration (coarsening) of the porous electrodes, and blocking of the reaction sites within the electrodes. Contact problems include delamination of an electrode from the electrolyte, growth of a poorly (electronically) conducting oxide layer between the metallic interconnect plates and the electrodes, and lack of contact between the interconnect and the electrode. INL's test results on high temperature electrolysis (HTE) using solid oxide cells do not provide a clear evidence whether different events lead to similar or drastically different electrochemical degradation mechanisms. Post-test examination of the solid oxide electrolysis cells showed that the hydrogen electrode and interconnect get partially oxidized and become non-conductive. This is most likely caused by the hydrogen stream composition and flow rate during cool down. The oxygen electrode side of the stacks seemed to be responsible for the observed degradation due to large areas of electrode delamination. Based on the oxygen electrode appearance, the degradation of these stacks was largely controlled by the oxygen electrode delamination rate. University of Utah (Virkar) has developed a SOEC model based on concepts in local thermodynamic equilibrium in systems otherwise in global thermodynamic non-equilibrium. This model is under continued development. It shows that electronic conduction through the electrolyte, however small, must be taken into account for determining local oxygen chemical potential, within the electrolyte. The chemical potential within the electrolyte may lie out of bounds in relation to values at the electrodes in the electrolyzer mode. Under certain conditions, high pressures can develop in the electrolyte just under the oxygen electrode (anode)/electrolyte interface, leading to electrode delamination. This theory is being further refined and tested by introducing some electronic conduction in the electrolyte.

M. S. Sohal; J. E. O'Brien; C. M. Stoots; V. I. Sharma; B. Yildiz; A. Virkar

2012-02-01T23:59:59.000Z

304

High temperature ablation resistance of ZrNp reinforced W matrix composites  

E-Print Network [OSTI]

modulus of elasticity, good thermal shock resistance, stiffness and good high temperature strengthHigh temperature ablation resistance of ZrNp reinforced W matrix composites Malik Adeel Umer microscopy (SEM) For the purpose of improving the high temperature ablation resistance of tungsten

Hong, Soon Hyung

305

Characterization of Composite Cores for High Temperature-Low Sag (HTLS)  

E-Print Network [OSTI]

Characterization of Composite Cores for High Temperature-Low Sag (HTLS) Conductors Final Project/University Cooperative Research Center since 1996 PSERC #12;Characterization of Composite Cores for High Temperature project T-33 titled "Characterization of Composite Cores for High Temperature-Low Sag (HTLS) Conductors

306

Nanostructured high-temperature superconductors: Creation of strong-pinning columnar defects in  

E-Print Network [OSTI]

Nanostructured high-temperature superconductors: Creation of strong-pinning columnar defects the growth and incorporation of MgO nanorods into high temperature superconductors (HTS's) has been developed a limitation to the performance of HTS materials at high temperatures and magnetic fields.11­13 The traditional

Yang, Peidong

307

Penetration of ac magnetic field into bulk high-temperature superconductors: Experiment and simulation  

E-Print Network [OSTI]

Penetration of ac magnetic field into bulk high-temperature superconductors: Experiment from these models for high-temperature superconductors are observed at the op- eration in ac fields condi- tions is very important for correct modeling magnetic prop- erties of high-temperature

Paperno, Eugene

308

In situ doping control of the surface of high-temperature superconductors  

E-Print Network [OSTI]

LETTERS In situ doping control of the surface of high-temperature superconductors M. A. HOSSAIN1 to systematic studies of high- temperature superconductors, such as creating new electron- doped superconductors.1038/nphys998 Central to the understanding of high-temperature superconductivity is the evolution

Michelson, David G.

309

Method of manufacturing a high temperature superconductor with improved transport properties  

SciTech Connect (OSTI)

A method of preparing a high temperature superconductor. A method of preparing a superconductor includes providing a powdered high temperature superconductor and a nanophase paramagnetic material. These components are combined to form a solid compacted mass with the paramagnetic material disposed on the grain boundaries of the polycrystaline high temperature superconductor.

Balachandran, Uthamalingam (Hinsdale, IL); Siegel, Richard W. (Hinsdale, IL); Askew, Thomas R. (Kalamazoo, MI)

2001-01-01T23:59:59.000Z

310

High Temperature Corrosion Behavior of Iron Aluminide Alloys and Coatings  

SciTech Connect (OSTI)

A multi-year effort has been focused on optimizing the long-term oxidation performance of ingot-processed (IP) and oxide-dispersion strengthened (ODS) Fe{sub 3}Al and iron aluminide-based coatings. Based on results from several composition iterations, a Hf-doped alloy (Fe-28Al-2Cr-0.05at.%Hf) has been developed with significantly better high temperature oxidation resistance than other iron aluminides. The scale adhesion is not significantly better; however, the {alpha}-Al{sub 2}O{sub 3} scale grows at a slower rate, approximately a factor of 10 less than undoped iron aluminide. The benefit of Hf is greatest at 1100-1200 C. Long-term oxidation resistance of commercially fabricated ODS Fe{sub 3}Al has been determined and compared to commercially available ODS FeCrAl. Scale spallation rates for ODS Fe{sub 3}Al are higher than for ODS FeCrAl. To complement studies of iron-aluminide weld-overlay coatings, carbon steel was coated with Fe-Al-Cr by thermal spraying. These specimens were then exposed in air at 900 and 1000 C and in air-1%SO{sub 2} at 800 C. Most likely due to an inadequate aluminum concentration in the coatings, continuous protective Al{sub 2}O{sub 3} could not be maintained and, consequently, the corrosion performance was significantly worse than what is normally observed for Fe{sub 3}Al.

Pint, B.A.

2001-10-22T23:59:59.000Z

311

Rotational viscometer for high-pressure, high-temperature fluids  

DOE Patents [OSTI]

The invention is a novel rotational viscometer which is well adapted for use with fluids at high temperatures and/or pressures. In one embodiment, the viscometer include a substantially non-magnetic tube having a closed end and having an open end in communication with a fluid whose viscosity is to be determined. An annular drive magnet is mounted for rotation about the tube. The tube encompasses and supports a rotatable shaft assembly which carries a rotor, or bob, for insertion in the fluid. Affixed to the shaft are (a) a second magnet which is magnetically coupled to the drive magnet and (b) a third magnet. In a typical operation, the drive magnet is rotated to turn the shaft assembly while the shaft rotor is immersed in the fluid. The viscous drag on the rotor causes the shaft assembly to lag the rotation of the drive magnet by an amount which is a function of the amount of viscous drag. A first magnetic pickup generates a waveform whose phase is a function of the angular position of the drive magnet. A second magnetic pickup generates a waveform whose phase is a function of the angular position of the third magnet. Means are provided to generate an output indicative of the phase difference between the two waveforms. The viscometer is comparatively simple, inexpensive, rugged, and does not require shaft seals.

Carr, K.R.

1983-06-06T23:59:59.000Z

312

Development of high temperature superconductors for magnetic field applications  

SciTech Connect (OSTI)

The key requirement for magnetic field applications of high temperature superconductor (HTS) materials is to have conductors with high transport critical current density available for magnet builders. After 3 or 4 years of being without any such object, conductor makers have had recent success in producing simple conductor prototypes. These have permitted the construction of simple HTS magnets having self fields exceeding 1 tesla at 4K. Thus the scientific feasibility of making powerful HTS magnets has been demonstrated. Attention to the technological aspects of making HTS conductors for magnets with strong flux pinning and reduced superconducting granularity is now sensible and attractive. However, extrinsic defects such as filament sausaging, cracking, misaligned grains and other perturbation to long range current flow must be controlled at a low level if the benefit of intrinsic improvements to the critical current density is to be maintained in the conductor form. Due to the great complexity of the HTS materials, there is sometimes confusion as to whether a given sample has an intrinsically or extrinsically limited critical current density. Systematic microstructure variation experiments and resistive transition analysis are shown to be particularly helpful in this phase of conductor development.

Larbalestier, D.C.

1991-01-01T23:59:59.000Z

313

Development of high temperature superconductors for magnetic field applications  

SciTech Connect (OSTI)

The key requirement for magnetic field applications of high temperature superconductor (HTS) materials is to have conductors with high transport critical current density available for magnet builders. After 3 or 4 years of being without any such object, conductor makers have had recent success in producing simple conductor prototypes. These have permitted the construction of simple HTS magnets having self fields exceeding 1 tesla at 4K. Thus the scientific feasibility of making powerful HTS magnets has been demonstrated. Attention to the technological aspects of making HTS conductors for magnets with strong flux pinning and reduced superconducting granularity is now sensible and attractive. However, extrinsic defects such as filament sausaging, cracking, misaligned grains and other perturbation to long range current flow must be controlled at a low level if the benefit of intrinsic improvements to the critical current density is to be maintained in the conductor form. Due to the great complexity of the HTS materials, there is sometimes confusion as to whether a given sample has an intrinsically or extrinsically limited critical current density. Systematic microstructure variation experiments and resistive transition analysis are shown to be particularly helpful in this phase of conductor development.

Larbalestier, D.C.

1991-12-31T23:59:59.000Z

314

Segmented lasing tube for high temperature laser assembly  

DOE Patents [OSTI]

A high temperature laser assembly capable of withstanding operating temperatures in excess of 1500.degree. C. is described comprising a segmented cylindrical ceramic lasing tube having a plurality of cylindrical ceramic lasing tube segments of the same inner and outer diameters non-rigidly joined together in axial alignment; insulation of uniform thickness surround the walls of the ceramic lasing tube; a ceramic casing, preferably of quartz, surrounding the insulation; and a fluid cooled metal jacket surrounds the ceramic casing. In a preferred embodiment, the inner surface of each of the ceramic lasing tube segments are provided with a pair of oppositely spaced grooves in the wall thereof parallel to the center axis of the segmented cylindrical ceramic lasing tube, and both of the grooves and the center axis of the segmented cylindrical ceramic lasing tube lie in a common plane, with the grooves in each ceramic lasing tube segment in circumferential alignment with the grooves in the adjoining ceramic lasing tube segments; and one or more ceramic plates, all lying in a common plane to one another and with the central axis of the segmented ceramic lasing tube, are received in the grooves to provide additional wall area in the segmented ceramic lasing tube for collision and return to ground state of metastable metal atoms within the segmented ceramic lasing tube.

Sawicki, Richard H. (Danville, CA); Alger, Terry W. (Tracy, CA); Finucane, Raymond G. (Pleasanton, CA); Hall, Jerome P. (Livermore, CA)

1996-01-01T23:59:59.000Z

315

Brazing Refractory Metals Used In High-Temperature Nuclear Instrumentation  

SciTech Connect (OSTI)

As part of the U. S. Department of Energy (DOE) sponsored Next Generation Nuclear Project (NGNP) currently ongoing at Idaho National Laboratory (INL), the irradiation performance of candidate high-temperature gas reactor fuels and materials is being evaluated at INL’s Advanced Test Reactor (ATR). The design of the first Advanced Gas Reactor (AGR 1) experiment, currently being irradiated in the ATR, required development of special techniques for brazing niobium and molybdenum. Brazing is one technique used to join refractory metals to each other and to stainless steel alloys. Although brazing processes are well established, it is difficult to braze niobium, molybdenum, and most other refractory metals because they quickly develop adherent oxides when exposed to room-temperature air. Specialized techniques and methods were developed by INL to overcome these obstacles. This paper describes the techniques developed for removing these oxides, as well as the ASME Section IX-qualified braze procedures that were developed as part of the AGR-1 project. All brazes were made using an induction coil with an inert or reducing atmosphere at low pressure. Other parameters, such as filler metals, fluxes used, and general setup procedures, are also discussed.

A. J. Palmer; C. J. Woolstenhulme

2009-06-01T23:59:59.000Z

316

Overcharge tolerant high-temperature cells and batteries  

DOE Patents [OSTI]

In a lithium-alloy/metal sulfide high temperature electrochemical cell, cell damage caused by overcharging is avoided by providing excess lithium in a high-lithium solubility phase alloy in the negative electrode and a specified ratio maximum of the capacity of a matrix metal of the negative electrode in the working phase to the capacity of a transition metal of the positive electrode. In charging the cell, or a plurality of such cells in series and/or parallel, chemical transfer of elemental lithium from the negative electrode through the electrolyte to the positive electrode provides sufficient lithium to support an increased self-charge current to avoid anodic dissolution of the positive electrode components above a critical potential. The lithium is subsequently electrochemically transferred back to the negative electrode in an electrochemical/chemical cycle which maintains high self-discharge currents on the order of 3-15 mA/cm.sup.2 in the cell to prevent overcharging.

Redey, Laszlo (Downers Grove, IL); Nelson, Paul A. (Wheaton, IL)

1989-01-01T23:59:59.000Z

317

Systems Engineering Provides Successful High Temperature Steam Electrolysis Project  

SciTech Connect (OSTI)

This paper describes two Systems Engineering Studies completed at the Idaho National Laboratory (INL) to support development of the High Temperature Stream Electrolysis (HTSE) process. HTSE produces hydrogen from water using nuclear power and was selected by the Department of Energy (DOE) for integration with the Next Generation Nuclear Plant (NGNP). The first study was a reliability, availability and maintainability (RAM) analysis to identify critical areas for technology development based on available information regarding expected component performance. An HTSE process baseline flowsheet at commercial scale was used as a basis. The NGNP project also established a process and capability to perform future RAM analyses. The analysis identified which components had the greatest impact on HTSE process availability and indicated that the HTSE process could achieve over 90% availability. The second study developed a series of life-cycle cost estimates for the various scale-ups required to demonstrate the HTSE process. Both studies were useful in identifying near- and long-term efforts necessary for successful HTSE process deployment. The size of demonstrations to support scale-up was refined, which is essential to estimate near- and long-term cost and schedule. The life-cycle funding profile, with high-level allocations, was identified as the program transitions from experiment scale R&D to engineering scale demonstration.

Charles V. Park; Emmanuel Ohene Opare, Jr.

2011-06-01T23:59:59.000Z

318

Gorkov equations for a pseudogapped high-temperature superconductor  

Science Journals Connector (OSTI)

A phenomenological theory of superconductivity based on the two-body Cooperon propagator is presented. This theory takes the form of a modified Gorkov equation for the Green’s function and allows one to model the effect of local superconducting correlations and long-range phase fluctuations on the spectral properties of high-temperature superconductors, both above and below Tc. A model is proposed for the Cooperon propagator, which provides a simple physical picture of the pseudogap phenomenon, as well as insights into the doping dependence of the spectral properties. Numerical calculations of the density of states and spectral functions based on this model are also presented, and compared with the experimental tunneling (STM) and photoemission (ARPES) data. It is found, in particular, that the sharpness of the peaks in the density of states is related to the strength and the range of the superconducting correlations and that the apparent pseudogap in STM and ARPES can be different, although the underlying model is the same.

B. Giovannini and C. Berthod

2001-03-21T23:59:59.000Z

319

Cryogenic System for a High Temperature Superconducting Power Transmission Cable  

SciTech Connect (OSTI)

High-temperature superconducting (HTS) cable systems for power transmission are under development that will use pressurized liquid nitrogen to provide cooling of the cable and termination hardware. Southwire Company and Oak Ridge National Laboratory have been operating a prototype HTS cable system that contains many of the typical components needed for a commercial power transmission application. It is being used to conduct research in the development of components and systems for eventual commercial deployment. The cryogenic system was built by Air Products and Chemicals, Allentown, Pennsylvania, and can circulate up to 0.35 kg/s of liquid nitrogen at temperatures as low as 67 K at pressures of 1 to 10 bars. Sufficient cooling is provided for testing a 5-m-long HTS transmission cable system that includes the terminations required for room temperature electrical connections. Testing of the 5-m HTS transmission cable has been conducted at the design ac conditions of 1250 A and 7.5 kV line to ground. This paper contains a description of the essential features of the HTS cable cryogenic system and performance results obtained during operation of the system. The salient features of the operation that are important in large commercial HTS cable applications will be discussed.

Demko, J.A.; Gouge, M.J.; Hughey, R.L.; Lue, J.W.; Martin, R.; Sinha, U.; Stovall, J.P.

1999-07-12T23:59:59.000Z

320

Test results of two high temperature superconducting sample coils  

SciTech Connect (OSTI)

Electrical measurements have been performed on two high temperature superconducting coils made by American Superconductor Corporation. One coil measured 24-mm ID, 59-mm OD, 50-mm long, and used 85-m long Y-124 tape conductor. The other coil measured 29-mm ID, 44-mm OD, 43-mm long, and used 35-m long Bi-2223 tape conductor. V-I curves were measured from room to helium temperature in a variable temperature cryostat cooled by helium gas in external fields up to 5 T. Without external field, the better performing Bi-2223 coil had a critical current, I{sub c} of 14.1 A (2820 A/cm{sup 2} over the conductor) at 4.2 K and 1.8 A (360 A/cm{sup 2}) at 77 K. At 5 T, I{sub c} was 4.9 A (980 A/cm{sup 2}) at 4.2 K and 2.0 A (400 A/cm{sup 2}) at 50 K. Reduced critical current, I{sub c}(B)/I{sub c}(0) vs field plots indicated that a single smooth curve could fit all the data of up to 50 K in temperature. The reduction in critical currents with external fields for the Y-124 coil was more than 80% at 1 T. For the Bi-2223 coil, it was about 38% at 1 T, and about 61% at 5 T.

Lue, J.W.; Schwenterly, S.W.; Lubell, M.S.; Luton, J.N. [Oak Ridge National Lab., TN (United States); Joshi, C.H.; Masur, L.J.; Podtburg, E.R. [American Superconductor Corp., Watertown, MA (United States)

1993-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Novel Gas Sensors for High-Temperature Fossil Fuel Applications  

SciTech Connect (OSTI)

SRI International (SRI) is developing ceramic-based microsensors to detect exhaust gases such as NO, NO{sub 2}, and CO in advanced combustion and gasification systems under this DOE NETL-sponsored research project. The sensors detect the electrochemical activity of the exhaust gas species on catalytic electrodes attached to a solid state electrolyte and are designed to operate at the high temperatures, elevated pressures, and corrosive environments typical of large power generation exhausts. The sensors can be easily integrated into online monitoring systems for active emission control. The ultimate objective is to develop sensors for multiple gas detection in a single package, along with data acquisition and control software and hardware, so that the information can be used for closed-loop control in novel advanced power generation systems. This report details the Phase I Proof-of-Concept, research activities performed from October 2003 to March 2005. SRI's research work includes synthesis of catalytic materials, sensor design and fabrication, software development, and demonstration of pulse voltammetric analysis of NO, NO{sub 2}, and CO gases on catalytic electrodes.

Palitha Jayaweera; Francis Tanzella

2005-03-01T23:59:59.000Z

322

Power efficiency for very high temperature solar thermal cavity receivers  

DOE Patents [OSTI]

This invention is an improved solar energy cavity receiver for exposing materials and components to high temperatures. The receiver includes a housing having an internal reflective surface defining a cavity and having an inlet for admitting solar radiation thereto. A photothermal absorber is positioned in the cavity to receive radiation from the inlet. A reflective baffle is positioned between the absorber and the inlet to severely restrict the re-radiation of energy through the inlet. The front surface of the baffle defines a narrow annulus with the internal reflective surface of the housing. The front surface of the baffle is contoured to reflect incoming radiation onto the internal surface of the housing, from which it is reflected through the annulus and onto the front surface of the absorber. The back surface of the baffle intercepts infrared radiation from the front of the absorber. With this arrangement, a high percentage of the solar power input is retained in the cavity; thus, high internal temperatures are attained.

McDougal, Allan R. (LaCanada-Flintridge, CA); Hale, Robert R. (Upland, CA)

1984-01-01T23:59:59.000Z

323

Characterization of High Temperature Mechanical Properties Using Laser Ultrasound  

SciTech Connect (OSTI)

Mechanical properties are controlled to a large degree by defect structures such as dislocations and grain boundaries. These microstructural features involve a perturbation of the perfect crystal lattice (i.e. strain fields). Viewed in this context, high frequency strain waves (i.e. ultrasound) provide a natural choice to study microstructure mediated mechanical properties. In this presentation we use laser ultrasound to probe mechanical properties of materials. This approach utilizes lasers to excite and detect ultrasonic waves, and as a consequence has unique advantages over other methods—it is noncontacting, requires no couplant or invasive sample preparation (other than that used in metallurgical analysis), and has the demonstrated capability to probe microstructure on a micron scale. Laser techniques are highly reproducible enabling sophisticated, microstructurally informed data analysis. Since light is being used for generation and detection of the ultrasonic wave, the specimen being examined is not mechanically coupled to the transducer. As a result, laser ultrasound can be carried out remotely, an especially attractive characteristic for in situ measurements in severe environments. Several examples involving laser ultrasound to measure mechanical properties in high temperature environments will be presented. Emphasis will be place on understanding the role of grain microstructure.

David Hurley; Stephen Reese; Farhad Farzbod; Rory Kennedy

2012-05-01T23:59:59.000Z

324

SunShot Initiative: A Small-Particle Solar Receiver for High-Temperature  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

A Small-Particle Solar Receiver A Small-Particle Solar Receiver for High-Temperature Brayton Power Cycles to someone by E-mail Share SunShot Initiative: A Small-Particle Solar Receiver for High-Temperature Brayton Power Cycles on Facebook Tweet about SunShot Initiative: A Small-Particle Solar Receiver for High-Temperature Brayton Power Cycles on Twitter Bookmark SunShot Initiative: A Small-Particle Solar Receiver for High-Temperature Brayton Power Cycles on Google Bookmark SunShot Initiative: A Small-Particle Solar Receiver for High-Temperature Brayton Power Cycles on Delicious Rank SunShot Initiative: A Small-Particle Solar Receiver for High-Temperature Brayton Power Cycles on Digg Find More places to share SunShot Initiative: A Small-Particle Solar Receiver for High-Temperature Brayton Power Cycles on AddThis.com...

325

Amorphous Alloy Membranes for High Temperature Hydrogen Separation  

SciTech Connect (OSTI)

At the beginning of this project, thin film amorphous alloy membranes were considered a nascent but promising new technology for industrial-scale hydrogen gas separations from coal- derived syngas. This project used a combination of theoretical modeling, advanced physical vapor deposition fabricating, and laboratory and gasifier testing to develop amorphous alloy membranes that had the potential to meet Department of Energy (DOE) targets in the testing strategies outlined in the NETL Membrane Test Protocol. The project is complete with Southwest Research Instituteź (SwRIź), Georgia Institute of Technology (GT), and Western Research Institute (WRI) having all operated independently and concurrently. GT studied the hydrogen transport properties of several amorphous alloys and found that ZrCu and ZrCuTi were the most promising candidates. GT also evaluated the hydrogen transport properties of V, Nb and Ta membranes coated with different transition-metal carbides (TMCs) (TM = Ti, Hf, Zr) catalytic layers by employing first-principles calculations together with statistical mechanics methods and determined that TiC was the most promising material to provide catalytic hydrogen dissociation. SwRI developed magnetron coating techniques to deposit a range of amorphous alloys onto both porous discs and tubular substrates. Unfortunately none of the amorphous alloys could be deposited without pinhole defects that undermined the selectivity of the membranes. WRI tested the thermal properties of the ZrCu and ZrNi alloys and found that under reducing environments the upper temperature limit of operation without recrystallization is ~250 °C. There were four publications generated from this project with two additional manuscripts in progress and six presentations were made at national and international technical conferences. The combination of the pinhole defects and the lack of high temperature stability make the theoretically identified most promising candidate amorphous alloys unsuitable for application as hydrogen separation membranes in coal fire systems.

Coulter, K

2013-09-30T23:59:59.000Z

326

Air Cooling for High Temperature Power Electronics (Presentation)  

SciTech Connect (OSTI)

Current emphasis on developing high-temperature power electronics, including wide-bandgap materials such as silicon carbide and gallium nitride, increases the opportunity for a completely air-cooled inverter at higher powers. This removes the liquid cooling system for the inverter, saving weight and volume on the liquid-to-air heat exchanger, coolant lines, pumps, and coolant, replacing them with just a fan and air supply ducting. We investigate the potential for an air-cooled heat exchanger from a component and systems-level approach to meet specific power and power density targets. A proposed baseline air-cooled heat exchanger design that does not meet those targets was optimized using a parametric computational fluid dynamics analysis, examining the effects of heat exchanger geometry and device location, fixing the device heat dissipation and maximum junction temperature. The CFD results were extrapolated to a full inverter, including casing, capacitor, bus bar, gate driver, and control board component weights and volumes. Surrogate ducting was tested to understand the pressure drop and subsequent system parasitic load. Geometries that met targets with acceptable loads on the system were down-selected for experimentation. Nine baseline configuration modules dissipated the target heat dissipation, but fell below specific power and power density targets. Six optimized configuration modules dissipated the target heat load, exceeding the specific power and power density targets. By maintaining the same 175 degrees C maximum junction temperature, an optimized heat exchanger design and higher device heat fluxes allowed a reduction in the number of modules required, increasing specific power and power density while still maintaining the inverter power.

Waye, S.; Musselman, M.; King, C.

2014-09-01T23:59:59.000Z

327

Protective interlayer for high temperature solid electrolyte electrochemical cells  

DOE Patents [OSTI]

The invention is comprised of an electrically conducting doped or admixed cerium oxide composition with niobium oxide and/or tantalum oxide for electrochemical devices, characterized by the general formula: Nb{sub x}Ta{sub y}Ce{sub 1{minus}x{minus}y}O{sub 2} where x is about 0.0 to 0.05, y is about 0.0 to 0.05, and x+y is about 0.02 to 0.05, and where x is preferably about 0.02 to 0.05 and y is 0, and a method of making the same is also described. This novel composition is particularly applicable in forming a protective interlayer of a high temperature, solid electrolyte electrochemical cell, characterized by a first electrode; an electrically conductive interlayer of niobium and/or tantalum doped cerium oxide deposited over at least a first portion of the first electrode; an interconnect deposited over the interlayer; a solid electrolyte deposited over a second portion of the first electrode, the first portion being discontinuous from the second portion; and, a second electrode deposited over the solid electrolyte. The interlayer is characterized as being porous and selected from the group consisting of niobium doped cerium oxide, tantalum doped cerium oxide, and niobium and tantalum doped cerium oxide or admixtures of the same. The first electrode, an air electrode, is a porous layer of doped lanthanum manganite, the solid electrolyte layer is a dense yttria stabilized zirconium oxide, the interconnect layer is a dense, doped lanthanum chromite, and the second electrode, a fuel electrode, is a porous layer of nickel-zirconium oxide cermet. The electrochemical cell can take on a plurality of shapes such as annular, planar, etc. and can be connected to a plurality of electrochemical cells in series and/or in parallel to generate electrical energy. 5 figs.

Singh, P.; Vasilow, T.R.; Richards, V.L.

1996-05-14T23:59:59.000Z

328

Protective interlayer for high temperature solid electrolyte electrochemical cells  

DOE Patents [OSTI]

The invention comprises of an electrically conducting doped or admixed cerium oxide composition with niobium oxide and/or tantalum oxide for electrochemical devices, characterized by the general formula: Nb.sub.x Ta.sub.y Ce.sub.1-x-y O.sub.2 where x is about 0.0 to 0.05, y is about 0.0 to 0.05, and x+y is about 0.02 to 0.05, and where x is preferably about 0.02 to 0.05 and y is 0, and a method of making the same. This novel composition is particularly applicable in forming a protective interlayer of a high temperature, solid electrolyte electrochemical cell (10), characterized by a first electrode (12); an electrically conductive interlayer (14) of niobium and/or tantalum doped cerium oxide deposited over at least a first portion (R) of the first electrode; an interconnect (16) deposited over the interlayer; a solid electrolyte (18) deposited over a second portion of the first electrode, the first portion being discontinuous from the second portion; and, a second electrode (20) deposited over the solid electrolyte. The interlayer (14) is characterized as being porous and selected from the group consisting of niobium doped cerium oxide, tantalum doped cerium oxide, and niobium and tantalum doped cerium oxide or admixtures of the same. The first electrode (12), an air electrode, is a porous layer of doped lanthanum manganite, the solid electrolyte layer (18) is a dense yttria stabilized zirconium oxide, the interconnect layer (16) is a dense, doped lanthanum chromite, and the second electrode (20), a fuel electrode, is a porous layer of nickel-zirconium oxide cermet. The electrochemical cell (10) can take on a plurality of shapes such as annular, planar, etc. and can be connected to a plurality of electrochemical cells in series and/or in parallel to generate electrical energy.

Singh, Prabhakar (Export, PA); Vasilow, Theodore R. (Manor, PA); Richards, Von L. (Angola, IN)

1996-01-01T23:59:59.000Z

329

The Astro-H high temperature superconductor lead assemblies  

Science Journals Connector (OSTI)

Abstract The Soft X-ray Spectrometer (SXS) instrument, one of several instruments on JAXA’s Astro-H mission, will observe diffuse X-ray sources with unparalleled spectral resolution using a microcalorimeter array operating at 50 mK. The array is cooled with a multi-stage Adiabatic Demagnetization Refrigerator mounted on a 40 l helium tank. The tank is at the center of a typical “shell in shell” cryostat, with the innermost shield cooled by a JT cryocooler, and successive outer shields cooled by stirling-cycle cryocoolers. To achieve a multi-year liquid helium lifetime and to avoid exceeding the limited capacity of the JT cooler, very strict requirements are placed on every source of heat leak into these surfaces from the higher temperature shields. However, each ADR stage draws a maximum of 2 A, and the Wiedemann–Franz Law precludes even an optimized set of normal-metal leads capable of such high current from achieving the required low thermal conductance. Instead, a set of lead assemblies have been developed based on narrow high temperature superconductor (HTS) tapes derived from commercially available coated conductors. Although the HTS tapes are flexible and have high tensile strength, they are extremely sensitive to damage through a number of mechanisms. A robust set of assemblies have been developed that provide mechanical support to the tapes, provide appropriate interfaces at either end, and yet still meet the challenging thermal requirements. An Engineering Model (EM) set of HTS lead assemblies have survived environmental testing, both as individual units and as part of the EM cryostat, and have performed without problem in recent operation of the EM instrument. The Flight Model (FM) HTS lead assemblies are currently nearing completion.

E.R. Canavan; B.L. James; T.P. Hait; A. Oliver; D.F. Sullivan

2014-01-01T23:59:59.000Z

330

High-temperature corrosion in advanced combustion systems  

SciTech Connect (OSTI)

Conceptual designs of advanced combustion systems that utilize coal as a feedstock require high temperature furnaces and heat transfer surfaces capable of operation at much elevated temperatures than those prevalent in current coal-fired power plants. The combination of elevated temperatures and hostile combustion environments necessitate development/application of advanced ceramic materials in these designs. The present paper characterizes the chemistry of coal-fired combustion environments over a wide temperature range of interest in these systems and discusses preliminary experimental results on several materials with potential for application in these systems. An experimental program has been initiated to evaluate materials for advanced combustion systems. Several candidate materials have been identified for evaluation. The candidates included advanced metallic alloys, monolithic ceramics, ceramic particulate/ceramic matrix composites, ceramic fiber/ceramic matrix composites, and ceramic whisker/ceramic matrix composites. The materials examined so far included nickel-base superalloys, alumina, stabilized zirconia, different types of silicon carbide, and silicon nitride. Coupon specimens of several of the materials have been tested in an air environment at 1000, 1200, and 1400{degree}C for 168 h. In addition, specimens were exposed to sodium-sulfate-containing salts at temperatures of 1000 and 1200{degree}C for 168 h. Extensive microstructural analyses were conducted on the exposed specimens to evaluate the corrosion performance of the materials for service in air and fireside environments of advanced coal-fired boilers. Additional tests are underway with several of the materials to evaluate their corrosion performance as a function of salt chemistry, alkali vapor concentration, gas chemistry, exposure temperature, and exposure time.

Natesan, K.; Yanez-Herrero, M.; Fornasieri, C.

1993-11-01T23:59:59.000Z

331

NOvel Refractory Materials for High Alkali, High Temperature Environments  

SciTech Connect (OSTI)

Refractory materials can be limited in their application by many factors including chemical reactions between the service environment and the refractory material, mechanical degradation of the refractory material by the service environment, temperature limitations on the use of a particular refractory material, and the inability to install or repair the refractory material in a cost effective manner or while the vessel was in service. The objective of this project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al2O3 spinel or other similar magnesia/alumina containing unshaped refractory composition (castables, gunnables, shotcretes, etc) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, highalkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries. A research team was formed to carry out the proposed work led by Oak Ridge National Laboratory (ORNL) and was comprised of the academic institution Missouri University of Science and Technology (MS&T), and the industrial company MINTEQ International, Inc. (MINTEQ), along with representatives from the aluminum, chemical, glass, and forest products industries. The two goals of this project were to produce novel refractory compositions which will allow for improved energy efficiency and to develop new refractory application techniques which would improve the speed of installation. Also methods of hot installation were sought which would allow for hot repairs and on-line maintenance leading to reduced process downtimes and eliminating the need to cool and reheat process vessels.

Hemrick, J.G.; Griffin, R. (MINTEQ International, Inc.)

2011-08-30T23:59:59.000Z

332

High temperature ceramic membrane reactors for coal liquid upgrading  

SciTech Connect (OSTI)

Membrane reactors are today finding extensive applications for gas and vapor phase catalytic reactions (see discussion in the introduction and recent reviews by Armor [92], Hsieh [93] and Tsotsis et al. [941]). There have not been any published reports, however, of their use in high pressure and temperature liquid-phase applications. The idea to apply membrane reactor technology to coal liquid upgrading has resulted from a series of experimental investigations by our group of petroleum and coal asphaltene transport through model membranes. Coal liquids contain polycyclic aromatic compounds, which not only present potential difficulties in upgrading, storage and coprocessing, but are also bioactive. Direct coal liquefaction is perceived today as a two-stage process, which involves a first stage of thermal (or catalytic) dissolution of coal, followed by a second stage, in which the resulting products of the first stage are catalytically upgraded. Even in the presence of hydrogen, the oil products of the second stage are thought to equilibrate with the heavier (asphaltenic and preasphaltenic) components found in the feedstream. The possibility exists for this smaller molecular fraction to recondense with the unreacted heavy components and form even heavier undesirable components like char and coke. One way to diminish these regressive reactions is to selectively remove these smaller molecular weight fractions once they are formed and prior to recondensation. This can, at least in principle, be accomplished through the use of high temperature membrane reactors, using ceramic membranes which are permselective for the desired products of the coal liquid upgrading process. An additional incentive to do so is in order to eliminate the further hydrogenation and hydrocracking of liquid products to undesirable light gases.

Tsotsis, T.T. (University of Southern California, Los Angeles, CA (United States). Dept. of Chemical Engineering); Liu, P.K.T. (Aluminum Co. of America, Pittsburgh, PA (United States)); Webster, I.A. (Unocal Corp., Los Angeles, CA (United States))

1992-01-01T23:59:59.000Z

333

Preventing fuel failure for a beyond design basis accident in a fluoride salt cooled high temperature reactor  

E-Print Network [OSTI]

The fluoride salt-cooled high-temperature reactor (FHR) combines high-temperature coated-particle fuel with a high-temperature salt coolant for a reactor with unique market and safety characteristics. This combination can ...

Minck, Matthew J. (Matthew Joseph)

2013-01-01T23:59:59.000Z

334

Presence of an alpha-amylase isozyme with high temperature optima in the wheat variety tolerant to high temperature at juvenile plant stage  

Science Journals Connector (OSTI)

In the present study ?-amylase was partially purified from detached grains of five day old seedlings of two wheat (Triticum aestivum L.) varieties, showing differential responses to high temperature stress at see...

Gurpreet Kaur Hunjan

2006-01-01T23:59:59.000Z

335

Improved Materials for High-Temperature Black Liquor Gasification  

SciTech Connect (OSTI)

The laboratory immersion test system built and operated at ORNL was found to successfully screen samples from numerous refractory suppliers, including both commercially available and experimental materials. This system was found to provide an accurate prediction of how these materials would perform in the actual gasifier environment. Test materials included mullites, alumino-silicate bricks, fusion-cast aluminas, alumina-based and chrome-containing mortars, phosphate-bonded mortars, coated samples provided under an MPLUS-funded project, bonded spinels, different fusion-cast magnesia-alumina spinels with magnesia content ranging from 2.5% to about 60%, high-MgO castable and brick materials, spinel castables, and alkali-aluminate materials. This testing identified several candidate material systems that perform well in the New Bern gasifier. Fusion-cast aluminas were found to survive for nearly one year, and magnesia-alumina spinels have operated successfully for 18 months and are expected to survive for two years. Alkali-aluminates and high-MgO-content materials have also been identified for backup lining applications. No other material with a similar structure and chemical composition to that of the fusion-cast magnesium-aluminum spinel brick currently being used for the hot-face lining is commercially available. Other materials used for this application have been found to have inferior service lives, as previously discussed. Further, over 100 laboratory immersion tests have been performed on other materials (both commercial and experimental), but none to date has performed as well as the material currently being used for the hot-face lining. Operating experience accumulated with the high-temperature gasifier at New Bern, North Carolina, has confirmed that the molten alkali salts degrade many types of refractories. Fusion-cast alumina materials were shown to provide a great improvement in lifetime over materials used previously. Further improvement was realized with fusion-cast magnesia-alumina spinel refractory, which appears to be the most resistant to degradation found to date, exhibiting over a year of service life and expected to be capable of over two years of service life. Regarding the use of refractory mortar, it was found that expansion of the current chrome-alumina mortar when subjected to black liquor smelt is likely contributing to the strains seen on the vessel shell. Additionally, the candidate high-alumina mortar that was originally proposed as a replacement for the current chrome-alumina mortar also showed a large amount of expansion when subjected to molten smelt. A UMR experimental mortar, composed of a phosphate bonded system specifically designed for use with fusion-cast magnesium-aluminum spinel, was found to perform well in the molten smelt environment. Strain gauges installed on the gasifier vessel shell provided valuable information about the expansion of the refractory, and a new set of strain gauges and thermocouples has been installed in order to monitor the loading caused by the currently installed spinel refractory. These results provide information for a direct comparison of the expansion of the two refractories. Measurements to date suggest that the fusion-cast magnesia-alumina spinel is expanding less than the fusion-cast {alpha}/{beta}-alumina used previously. A modified liquor nozzle was designed and constructed to test a number of materials that should be more resistant to erosion and corrosion than the material currently used. Inserts made of three erosion-resistant metallic materials were fabricated, along with inserts made of three ceramic materials. The assembled system was sent to the New Bern mill for installation in the gasifer in 2005. Following operation of the gasifier using the modified nozzle, inserts should be removed and analyzed for wear by erosion/corrosion. Although no materials have been directly identified for sensor/thermocouple protection tubes, several of the refractory material systems identified for lining material applications may be applicable for use in this

Keiser, J.R.; Hemrick, J.G.; Gorog, J.P.; Leary, R.

2006-06-29T23:59:59.000Z

336

High-Temperature Components for Rankine-Cycle-Based Waste Heat...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Components for Rankine-Cycle-Based Waste Heat Recovery Systems on Combustion Engines High-Temperature Components for Rankine-Cycle-Based Waste Heat Recovery Systems on...

337

High-Temperature Circuit Boards for use in Geothermal Well Monitoring...  

Open Energy Info (EERE)

the very high temperatures (on the order of 350C) in EGS wells. Therefore, Composite Technology Development, Calumet, A-Power, and Sandia National Laboratory are...

338

High temperature affects olive fruit fly populations in California’s Central Valley  

E-Print Network [OSTI]

High temperature affects olive fruit fly populations inand Kent M. Daane Olive fruit fly commonly infests olives inthat trap counts for olive fruit fly adults in pesticide­

2011-01-01T23:59:59.000Z

339

High-Temperature Motor Windings for Downhole Pumps Used in Geothermal Energy Production  

Broader source: Energy.gov [DOE]

Project objective: Develop and demonstrate high-temperature ESP motor windings for use in Enhanced Geothermal Systems and operation at 300?C.

340

Project Profile: A Novel Storage Method for CSP Plants Allowing Operation at High Temperature  

Broader source: Energy.gov [DOE]

City College of New York (CCNY), under the Thermal Storage FOA, is developing and testing a novel thermal storage method that allows operation at very high temperatures.

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

New Membranes for High Temperature Proton Exchange Membrane Fuel Cells Based on Heteropoly Acids  

Broader source: Energy.gov [DOE]

"Summary of Colorado School of Mines heteropolyacid research presented to the High Temperature Membrane Working Group Meeting, Orlando FL, October 17, 2003 "

342

A Discussion of Testing Protocols and LANL's Contribution to High Temperature Membranes  

Broader source: Energy.gov [DOE]

Summary of LANL?s testing protocol work presented to the High Temperature Membrane Working Group Meeting, Orlando FL, October 17, 2003

343

E-Print Network 3.0 - aqueous high-temperature chemistry Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

tolerant PEM Fuel Cell System utilizing advanced components, high temperature membrane Praxair Process... Technology Administration U.S. Department of Commerce...

344

High Temperature Membrane Working Group, Minutes of Meeting on September 14, 2006  

Broader source: Energy.gov [DOE]

These meeting minutes provide information about the High Temperature Membrane Working Group meeting on September 14, 2006 in San Francisco, Ca.

345

Thermal expansion of manganese dioxide using high-temperature in situ X-ray diffraction  

Science Journals Connector (OSTI)

The thermal expansion behaviour of manganese dioxide, an important battery material, is reported using high-temperature in situ X-ray diffraction between 298 and 673 K.

Dose, W.M.

2013-08-03T23:59:59.000Z

346

Limiting Factors for High Temperature Operation of THz Quantum Cascade Lasers  

Science Journals Connector (OSTI)

We theoretically investigate the temperature dependence of the carrier transport in GaAs-based THz quantum cascade lasers and identify the factors restricting high-temperature...

Jirauschek, Christian; Lugli, Paolo

347

Levitation Performance of Bulk High Temperature Superconductor Above the Permanent Magnet Guideway at Different Temperatures  

Science Journals Connector (OSTI)

The levitation performance of a high temperature superconducting (HTS) Maglev system was investigated at different temperatures for HTS Maglev vehicle application. Using a cryogenic measurement system, we stud...

Hua Jing; Suyu Wang; Ming Jiang; Jiasu Wang

2010-12-01T23:59:59.000Z

348

Modeling and experimental investigation of microstrip resonators and filters based on High-Temperature Superconductor films  

Science Journals Connector (OSTI)

Complex approach to the investigation of microstrip resonators and filters based on High-Temperature Superconductor (HTS) films is described, which includes...

M. F. Sitnikova; I. B. Vendik; O. G. Vendik; D. V. Kholodnyak…

2010-09-01T23:59:59.000Z

349

High-Temperature Superconductor Coil System for a Particle Detector Analyzing Magnet  

Science Journals Connector (OSTI)

The high energy physics experiment known as the Main ... . We have evaluated the feasibility of a high-temperature superconductor coil system that provides a 25,000...

R. C. Niemann; L. R. Turner; M. W. Morgan; P. Haldar…

1998-01-01T23:59:59.000Z

350

Electrodynamics of high-temperature superconductors investigated with coherent terahertz pulse spectroscopy  

Science Journals Connector (OSTI)

Recent experimental investigations of the electrodynamic properties of high-temperature superconductors in the terahertz regime are reviewed. Transmission measurements were performed...

Brorson, S D; Buhleier, R; Trofimov, I E; White, J O; Ludwig, Ch; Balakirev, F F; Habermeier, H -U; Kuhl, Juergen

1996-01-01T23:59:59.000Z

351

Project Profile: High-Temperature Thermal Array for Next-Generation...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Thermal Array for Next-Generation Solar Thermal Power Production Project Profile: High-Temperature Thermal Array for Next-Generation Solar Thermal Power Production Los Alamos...

352

High-Temperature Motor Windings for Downhole Pumps Used in Geothermal...  

Broader source: Energy.gov (indexed) [DOE]

and Other Harsh Environments High-Temperature Motor Windings for Downhole Pumps Used in Geothermal Energy Production Matthew Hooker Composite Technology Development, Inc....

353

High-temperature sorbent method for removal of sulfur containing gases from gaseous mixtures  

DOE Patents [OSTI]

A copper oxide-zinc oxide mixture is used as a sorbent for removing hydrogen sulfide and other sulfur containing gases at high temperatures from a gaseous fuel mixture. This high-temperature sorbent is especially useful for preparing fuel gases for high temperature fuel cells. The copper oxide is initially reduced in a preconditioning step to elemental copper and is present in a highly dispersed state throughout the zinc oxide which serves as a support as well as adding to the sulfur sorption capacity. The spent sorbent is regenerated by high-temperature treatment with an air fuel, air steam mixture followed by hydrogen reduction to remove and recover the sulfur.

Young, John E. (Woodridge, IL); Jalan, Vinod M. (Concord, MA)

1984-01-01T23:59:59.000Z

354

High-temperature sorbent method for removal of sulfur-containing gases from gaseous mixtures  

DOE Patents [OSTI]

A copper oxide-zinc oxide mixture is used as a sorbent for removing hydrogen sulfide and other sulfur containing gases at high temperatures from a gaseous fuel mixture. This high-temperature sorbent is especially useful for preparing fuel gases for high temperature fuel cells. The copper oxide is initially reduced in a preconditioning step to elemental copper and is present in a highly dispersed state throughout the zinc oxide which serves as a support as well as adding to the sulfur sorbtion capacity. The spent sorbent is regenerated by high-temperature treatment with an air fuel, air steam mixture followed by hydrogen reduction to remove and recover the sulfur.

Young, J.E.; Jalan, V.M.

1982-07-07T23:59:59.000Z

355

High-temperature sorbent method for removal of sulfur containing gases from gaseous mixtures  

DOE Patents [OSTI]

A copper oxide-zinc oxide mixture is used as a sorbent for removing hydrogen sulfide and other sulfur containing gases at high temperatures from a gaseous fuel mixture. This high-temperature sorbent is especially useful for preparing fuel gases for high temperature fuel cells. The copper oxide is initially reduced in a preconditioning step to elemental copper and is present in a highly dispersed state throughout the zinc oxide which serves as a support as well as adding to the sulfur sorption capacity. The spent sorbent is regenerated by high-temperature treatment with an air fuel, air steam mixture followed by hydrogen reduction to remove and recover the sulfur.

Young, J.E.; Jalan, V.M.

1984-06-19T23:59:59.000Z

356

Concept of a thermonuclear reactor based on gravity retention of high-temperature plasma  

E-Print Network [OSTI]

In the present paper the realization of the obtained results in relation to the dense high- temperature plasma of multivalent ions including experimental data interpretation is discussed.

S. I. Fisenko; I. S. Fisenko

2007-05-27T23:59:59.000Z

357

High-Temperature Circuit Boards for Use in Geothermal Well Monitoring...  

Broader source: Energy.gov (indexed) [DOE]

Composite Technology Development, Inc. High-Temperature Tools and Sensors, Downhole Pumps and Drilling May 19, 2010 This presentation does not contain any proprietary...

358

Sintering and properties of Ultra High Temperature Ceramics for aerospace applications J.F. Justin  

E-Print Network [OSTI]

thermal shock resistance and makes them ideal for many high-temperature thermal applications : France (2013)" #12;for example, a high thermal conductivity reduces thermal stress within the material-francois.justin@onera.fr ABSTRACT The Ultra High Temperature Ceramics (UHTCs) represent a very interesting family of materials

359

Simulation of the high temperature impression of thermal barrier coatings with columnar microstructure  

E-Print Network [OSTI]

the deformation resistance of actual EB-PVD layers and its application to a range of thermal barrier materials [9Simulation of the high temperature impression of thermal barrier coatings with columnar of thermal barrier coatings (TBCs) are affected by their high temperature mechanical properties: especially

Hutchinson, John W.

360

THE USE OF TERNARY PHASE DIAGRAMS IN THE STUDY OF HIGH TEMPERATURE CORROSION  

E-Print Network [OSTI]

THE USE OF TERNARY PHASE DIAGRAMS IN THE STUDY OF HIGH TEMPERATURE CORROSION PRODUCTS FORMED ON Fe'' and resulting morphologies that may occur during formation of corrosion scales from high temperature gaseous the previously formed reaction products was found to produce internal corrosion phases within the alloy

DuPont, John N.

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Transmission electron energy-loss spectroscopy study of carbon nanotubes upon high temperature treatment  

E-Print Network [OSTI]

Transmission electron energy-loss spectroscopy study of carbon nanotubes upon high temperature electron energy-loss spectroscopy study of carbon nanotubes upon high temperature treatment B. W. Reed, M of carbon nanotube materials, grown with a pulsed-laser deposition technique but purified and heat treated

Bertsch George F.

362

Short Channel Amorphous-Silicon TFT's on High-Temperature Clear Plastic Substrates  

E-Print Network [OSTI]

Short Channel Amorphous-Silicon TFT's on High-Temperature Clear Plastic Substrates K. Long, H@princeton.edu To achieve light-weight flexible AMOLED displays on plastic substrates, the substratesmust be optically clear for plastic. High-temperature plastics such as polyimide (e.g. KaptonB E) have a glass transition temperature

363

DSC Evidence for Microstructure and Phase Transitions in Polyethylene Melts at High Temperatures  

E-Print Network [OSTI]

DSC Evidence for Microstructure and Phase Transitions in Polyethylene Melts at High Temperatures polyethylenes of types HDPE, LDPE, and LLDPE. DSC data were obtained for a range of heating and cooling rates previous rheology findings of order and high-temperature transitions in polyethylene melts. Introduction

Hussein, Ibnelwaleed A.

364

Infrared emission spectroscopy of CO2 at high temperature. Part II: Experimental results and  

E-Print Network [OSTI]

Infrared emission spectroscopy of CO2 at high temperature. Part II: Experimental results-92322 Ch^atillon, France Abstract Measurements of CO2 emission spectra at high temperature in the 2.7 ”m emission measurements using a microwave post-discharge in CO2 flow as emission source. The measurements

Paris-Sud XI, Université de

365

Local antiferromagnetic exchange and collaborative Fermi surface as key ingredients of high temperature superconductors  

E-Print Network [OSTI]

and ferrochalcogenides are three classes of unconventional high- temperature superconductors, who share similar phase interactions. Our result offers a principle guide to search for new high temperature superconductors. 1 ar temperature superconductors Jiangping Hu1, 2, and Hong Ding1, 1 Beijing National Laboratory for Condensed

Hu, Jiangping

366

Competing order and the asymmetric tunneling spectrum in high temperature cuprate superconductors  

E-Print Network [OSTI]

Competing order and the asymmetric tunneling spectrum in high temperature cuprate superconductors- terplay between them are two major tasks in this field. In high temperature cuprate superconductors temperature superconductors remains a challenging puzzle to be solved. A comprehensive theory to understand

Hu, Jiangping

367

A. Bianconi (ed.) Symmetry and Heterogeneity in High Temperature Superconductors, 21-53  

E-Print Network [OSTI]

A. Bianconi (ed.) Symmetry and Heterogeneity in High Temperature Superconductors, 21-53 NATO I.2 FESHBACH SHAPE RESONANCES IN MULTIBAND HIGH TC SUPERCONDUCTORS Antonio Bianconi, Matteo Filippi trick that bestows to the system the property to resist to the decoherence attacks of high temperature

368

"Phun" with Photoelectrons What Sets the Tc in Cuprate High-Temperature Superconductors?  

E-Print Network [OSTI]

"Phun" with Photoelectrons or What Sets the Tc in Cuprate High-Temperature Superconductors? Dan famous and exotic of correlated electron materials are high-temperature cuprate superconductors, which the pair-breaking energy scale . In contrast to conventional superconductors in which the superconducting

Glashausser, Charles

369

Performance and endurance of a high temperature PEM fuel cell operated on methanol reformate  

E-Print Network [OSTI]

Performance and endurance of a high temperature PEM fuel cell operated on methanol reformate Samuel September 2014 Available online xxx Keywords: High temperature PEM Fuel cell Methanol Impedance spectroscopy]. The report forecasts even more success for fuel cells in the near future. Proton exchange membrane (PEM) fuel

KĂŠr, SĂžren Knudsen

370

Proceedings of the conference on numerical methods in high temperature physics  

SciTech Connect (OSTI)

These proceedings contain full papers presented at the Los Alamos Conference on High Temperature Physics. This conference discussed many aspects of high temperature physics including hydrodynamics, radiation and particle transport and some computational issues important for efficient calculations. The meetings was held between researchers from Los Alamos and the French Commissariat a L'Energy Atomique (CEA).

Alcouffe, R.E.; Holm, D.D.; O'Rourke, P.J. (comps.)

1988-11-01T23:59:59.000Z

371

EA-1867: Scale-up of High-Temperature Syngas Cleanup Technology, Polk  

Broader source: Energy.gov (indexed) [DOE]

7: Scale-up of High-Temperature Syngas Cleanup Technology, 7: Scale-up of High-Temperature Syngas Cleanup Technology, Polk County, Florida EA-1867: Scale-up of High-Temperature Syngas Cleanup Technology, Polk County, Florida Summary This EA evaluates the environmental impacts of a proposal to provide cost-shared funding to RTI International (RTI) for its proposed project to demonstrate the precommercial scale-up of RTI's high-temperature syngas cleanup and carbon capture and sequestration technologies. Public Comment Opportunities No public comment opportunities available at this time. Documents Available for Download October 13, 2011 EA-1867: Finding of No Significant Impact RTI International Scale-Up of High-Temperature Syngas Cleanup and Carbon Capture and Sequestration Technologies, Polk County, Florida (October 2011)

372

EA-0510: High-Temperature Solid Oxide Fuel Cell (Sofc) Generator  

Broader source: Energy.gov (indexed) [DOE]

510: High-Temperature Solid Oxide Fuel Cell (Sofc) Generator 510: High-Temperature Solid Oxide Fuel Cell (Sofc) Generator Development Project (METC), Churchill, Pennsylvania EA-0510: High-Temperature Solid Oxide Fuel Cell (Sofc) Generator Development Project (METC), Churchill, Pennsylvania SUMMARY This EA evaluates the environmental impacts of a proposal to enter into a 5-year cooperative agreement with the Westinghouse Electric Corporation for the development of high-temperature solid oxide fuel cell generators near Pittsburgh, Pennsylvania. PUBLIC COMMENT OPPORTUNITIES None available at this time. DOCUMENTS AVAILABLE FOR DOWNLOAD August 1, 1991 EA-0510: Final Environmental Assessment High-Temperature Solid Oxide Fuel Cell (Sofc) Generator Development Project (METC) August 1, 1991 EA-0510: Finding of No Significant Impact

373

High resolution angle-resolved photoemission study of high temperature superconductors: charge-ordering, bilayer splitting and electron-phonon coupling  

E-Print Network [OSTI]

study of high temperature superconductors: charge-ordering,work on high temperature superconductors. These include: (1)interaction in high temperature superconductors. ? 2002

Zhou, Xingjiang; Hussain, Zahid; Shen, Zhi-xun

2003-01-01T23:59:59.000Z

374

A universal high energy anomaly in angle resolved photoemission spectra of high temperature superconductors -- possible evidence of spinon and holon branches  

E-Print Network [OSTI]

spectra of high temperature superconductors – possiblefamilies of high temperature superconductors by using angle-families of high temperature superconductors, identi?ed by a

2006-01-01T23:59:59.000Z

375

Categorical Exclusion Determinations: West Virginia | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

July 15, 2010 July 15, 2010 CX-003070: Categorical Exclusion Determination Gas Process Development Unit (GPDU)/Syngas (Synthetic Gas) Generator Decommissioning CX(s) Applied: B1.23, B1.27, B1.31, B3.6 Date: 07/15/2010 Location(s): Morgantown, West Virginia Office(s): Fossil Energy, National Energy Technology Laboratory July 8, 2010 CX-002903: Categorical Exclusion Determination High-Temperature Nano-Derived Micro-H2 (Hydrogen) and -H2S (Hydrogen Sulfide) Sensors CX(s) Applied: B3.6 Date: 07/08/2010 Location(s): Morgantown, West Virginia Office(s): Fossil Energy, National Energy Technology Laboratory June 21, 2010 CX-002726: Categorical Exclusion Determination Energy Efficiency in State Buildings: Health and Human Resources CX(s) Applied: B1.24, B1.28, B1.31, B2.2, A9, B1.5, B5.1

376

Two-phase chromium-niobium alloys exhibiting improved mechanical properties at high temperatures  

DOE Patents [OSTI]

The specification discloses chromium-niobium alloys which exhibit improved mechanical properties at high temperatures in the range of 1250.degree. C. and improved room temperature ductility. The alloys contain a Cr.sub.2 Nb-rich intermetallic phase and a Cr-rich phase with an overall niobium concentration in the range of from about 5 to about 18 at. %. The high temperature strength is substantially greater than that of state of the art nickel-based superalloys for enhanced high temperature service. Further improvements in the properties of the compositions are obtained by alloying with rhenium and aluminum; and additional rare-earth and other elements.

Liu, Chain T. (Oak Ridge, TN); Takeyama, Masao (Tokyo, JP)

1994-01-01T23:59:59.000Z

377

Two-phase chromium-niobium alloys exhibiting improved mechanical properties at high temperatures  

DOE Patents [OSTI]

The specification discloses chromium-niobium alloys which exhibit improved mechanical properties at high temperatures in the range of 1250 C and improved room temperature ductility. The alloys contain a Cr[sub 2]Nb-rich intermetallic phase and a Cr-rich phase with an overall niobium concentration in the range of from about 5 to about 18 at. %. The high temperature strength is substantially greater than that of state of the art nickel-based superalloys for enhanced high temperature service. Further improvements in the properties of the compositions are obtained by alloying with rhenium and aluminum; and additional rare-earth and other elements. 14 figures.

Liu, C.T.; Takeyama, Masao.

1994-02-01T23:59:59.000Z

378

What Causes High-temperature Superconductivity? | U.S. DOE Office of  

Office of Science (SC) Website

What Causes High-temperature Superconductivity? What Causes High-temperature Superconductivity? Basic Energy Sciences (BES) BES Home About Research Facilities Science Highlights Benefits of BES Funding Opportunities Basic Energy Sciences Advisory Committee (BESAC) News & Resources Contact Information Basic Energy Sciences U.S. Department of Energy SC-22/Germantown Building 1000 Independence Ave., SW Washington, DC 20585 P: (301) 903-3081 F: (301) 903-6594 E: sc.bes@science.doe.gov More Information » March 2013 What Causes High-temperature Superconductivity? A phase change at absolute zero temperature may provide key insights into the decades-old mystery of high-temperature superconductivity. Print Text Size: A A A Subscribe FeedbackShare Page Click to enlarge photo. Enlarge Photo Image courtesy of Ames Laboratory

379

An integrated performance model for high temperature gas cooled reactor coated particle fuel  

E-Print Network [OSTI]

The performance of coated fuel particles is essential for the development and deployment of High Temperature Gas Reactor (HTGR) systems for future power generation. Fuel performance modeling is indispensable for understanding ...

Wang, Jing, 1976-

2004-01-01T23:59:59.000Z

380

Thermomechanical Cyclic Response of TiNiPd High-Temperature Shape Memory Alloys  

E-Print Network [OSTI]

TiNiPd high-temperature shape memory alloys (HTSMAs) have attracted considerable attention as potential solid-state actuators capable of operating at temperatures up to 500 °C, exhibiting excellent corrosion resistance, adequate ductility levels...

Atli, Kadri

2012-10-19T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Computational Thermodynamics of CoNiGa High Temperature Shape Memory Alloys  

E-Print Network [OSTI]

Shape Memory Alloys (SMAs) are advanced materials with interesting properties such as pseudoelasticity (PE) and the shape memory effect (SME). Recently, the CoNiGa system has emerged as the basis for very promising High Temperature Shape Memory...

Chari, Arpita

2012-10-19T23:59:59.000Z

382

Overview of Fraunhofer IPM Activities in High Temperature Bulk Materials and Device Development  

Broader source: Energy.gov [DOE]

Presentation given at the 2011 Thermoelectrics Applications Workshop including an overview about Fraunhofer IPM, new funding situation in Germany, high temperature material and modules, energy-autarkic sensors, and thermoelectric metrology.

383

Applied High-Temperature Superconductor Bulks and Wires to Rotating Machines for Marine Propulsion  

Science Journals Connector (OSTI)

High-temperature superconductors (HTS) allow providing to high-torque density rotating machines a compact, efficient, and excellent operation. Field poles that act as magnets, providing a magnetic field of more t...

Brice Felder; Motohiro Miki; Yosuke Kimura…

2011-01-01T23:59:59.000Z

384

High pressure/high temperature hydrogen permeability in candidate stirling engine alloys  

Science Journals Connector (OSTI)

Hydrogen permeation tests of eight high-temperature engineering alloys were conducted in 20.7 MPa hydrogen at 923 to 1088 K for assessing suitability in Stirling engine application for heater head and heater head...

S. Bhattacharyya; E. J. Vesely; V. L. Hill

1982-03-01T23:59:59.000Z

385

Magnetic reconnection as a possible heating mechanism of the local high temperature protons within magnetic clouds  

Science Journals Connector (OSTI)

Magnetic clouds have the outstanding observational features of low proton temperature and plasma beta value, but numerous observations show that some magnetic clouds often have local high temperature phenomena...

HengQiang Feng; JieMin Wang

2014-08-01T23:59:59.000Z

386

Iron-niobium-aluminum alloy having high-temperature corrosion resistance  

DOE Patents [OSTI]

An alloy for use in high temperature sulfur and oxygen containing environments, having aluminum for oxygen resistance, niobium for sulfur resistance and the balance iron, is discussed. 4 figs., 2 tabs.

Hsu, Huey S.

1988-04-14T23:59:59.000Z

387

Non-linear Dynamical Reliability Analysis in the Very High Temperature Gas Cooled Reactor  

Science Journals Connector (OSTI)

A dynamic safety assessment has been developed for the passive system in the very high temperature gas cooled reactor (VHTR), where the operational data are deficient. It is needed to make use of the character...

Taeho Woo

2012-01-01T23:59:59.000Z

388

High-Temperature Stress Relaxation Cracking and Stress Rupture Observed in a Coke Gasifier Failure  

Science Journals Connector (OSTI)

This article discusses the high-temperature metal degradation mechanisms that occurred in the failure of a nine-story tall coke gasifier, located in a refinery power plant. Cracking of gasifier internals, bulging...

Daniel J. Benac; Douglas B. Olson…

2011-06-01T23:59:59.000Z

389

Enhancing Shale Gas Recovery by High-Temperature Supercritical CO2 Flooding  

Science Journals Connector (OSTI)

We examine a new technology for shale gas recovery: high-temperature supercritical carbon dioxide flooding ... of supercritical carbon dioxide, the characteristics of shale gas reservoirs, the adsorption/desorpti...

Feiying Ma; Yongqing Wang; Lin Wang

2013-09-01T23:59:59.000Z

390

Measurement of the vortex depinning force in a high temperature superconductor  

E-Print Network [OSTI]

Introduction: Superconductivity is one of those subjects in physics that is as captivating theoretically as it is experimentally interesting. The dual driving force of commercial demand for high-temperature superconductors ...

Whitehead, Andrew Patrick

2005-01-01T23:59:59.000Z

391

Calculating levitation forces in the magnet-high-temperature superconductor systems  

Science Journals Connector (OSTI)

A new method of calculation of the magnetic levitation force in the permanent magnet-high-temperature superconductor systems is proposed based on the Maxwell ... the gap width calculated for various regimes of superconductor

Yu. S. Ermolaev; I. A. Rudnev

2005-12-01T23:59:59.000Z

392

Imaging the two gaps of the high temperature superconductor Pb-Bi?Sr?CuO??x  

E-Print Network [OSTI]

The nature and behavior of electronic states in high temperature superconductors are the center of much debate. The pseudogap state, observed above the superconducting transition temperature Tc, is seen by some as a precursor ...

Yi, Ming, S.M. Massachusetts Institute of Technology

2007-01-01T23:59:59.000Z

393

Femtosecond Study of Photodoping Phenomena in a Parent Compound of a High-Temperature Superconductor  

Science Journals Connector (OSTI)

We present the first spectrally-resolved study of the femtosecond dynamics in La2CuO4, the undoped parent-compound of the high-temperature superconductor. The...

Beyer, Markus; Kim, Kyungwan; Kabanov, Viktor; Schäfer, Hanjo; Logvenov, Gennady; Bozovic, Ivan; Demsar, Jure

394

Receiver protecting device based on microstrip structure with high-temperature superconductor film  

Science Journals Connector (OSTI)

New design of an effective device for protection against high-power electromagnetic pulses has been created based ... third resonator based on a thin film of high-temperature superconductor (HTSC) occurring in th...

B. A. Belyaev; I. V. Govorun; A. A. Leksikov; A. M. Serzhantov

2012-03-01T23:59:59.000Z

395

Local characteristics of heat-radiation superconductor detectors based on high-temperature superconductor films  

Science Journals Connector (OSTI)

Relations are proposed for evaluating the local values of the thermal sensitivity, speed of response, and resolution of a heat radiation detector based on high-temperature superconductor films.

O. S. Esikov; A. I. Krot; I. G. Merinov…

1992-06-01T23:59:59.000Z

396

Studies of heterogeneity properties of selected high-temperature superconductor surfaces  

Science Journals Connector (OSTI)

Nitrogen adsorption measured at 77 K was used to characterize the surface heterogeneity of high-temperature superconductor surfaces. Properties relating to adsorption and porosity ... microscopy (AFM) for a serie...

P. Staszczuk; D. Sternik; G. W. Ch?dzy?ski…

2006-09-01T23:59:59.000Z

397

Features of technology of high-temperature superconductor films for microwave filters  

Science Journals Connector (OSTI)

The characteristics of fourth-order bandpass microwave filters based on high-temperature super-conductor (HTS) films have been numerically simulated and experimentally measured for the devices based on YBCO fi...

I. B. Vendik; O. G. Vendik; K. N. Zemlyakov; I. V. Kolmakova…

2011-05-01T23:59:59.000Z

398

Development and Investigation of a Dipole Magnet with a High-Temperature Superconductor Winding  

Science Journals Connector (OSTI)

The structure of a dipole magnet with an iron yoke, where the winding is made of a Bi-2223 high-temperature superconductor, has been developed and the magnet has been built at the Institute of High-Energy Physics...

A. I. Ageev; I. V. Bogdanov; V. V. Zubko; S. S. Kozub; K. P. Myznikov…

2002-12-01T23:59:59.000Z

399

High Temperature Materials Laboratory User Program: 19th Annual Report, October 1, 2005 - September 30, 2006  

SciTech Connect (OSTI)

Annual Report contains overview of the High Temperature Materials Laboratory User Program and includes selected highlights of user activities for FY2006. Report is submitted to individuals within sponsoring DOE agency and to other interested individuals.

Pasto, Arvid [ORNL

2007-08-01T23:59:59.000Z

400

Bimodal solar system based on a ultra-high-temperature TEC  

SciTech Connect (OSTI)

The paper considers an ecological, solar, bimodal system with ultra-high temperature thermionic energy converter (TEC). The solar bimodal Space Electric Propulsion System (SEPS) characteristics are presented. {copyright} {ital 1996 American Institute of Physics.}

Ogloblin, B.G.; Kirillov, E.Y.; Klimov, A.V.; Shalaev, A.I.; Shumov, D.P. [Central Design Bureau of Machine Building, Krasnogvardeyskaya Square 3, St. Petersburg, (Russia) 195272; Ender, A.Y.; Kuznetsov, V.I.; Sitnov, V.I. [Ioffe Physico-Technical Institute, Politekhnicheskaya St. 26, St. Petersburg, (Russia) 194021

1996-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Recent developments in high-temperature photonic crystals for energy conversion  

E-Print Network [OSTI]

After decades of intense studies focused on cryogenic and room temperature nanophotonics, scientific interest is also growing in high-temperature nanophotonics aimed at solid-state energy conversion. These latest extensive ...

Rinnerbauer, Veronika

402

A method for carbon oxide concentration evaluation in high-temperature combustion processes  

Science Journals Connector (OSTI)

A method for evaluating carbon oxide concentration in high-temperature combustion processes is presented. The paper offers an optimizing control problem for fuel combustion process using a stabilizing regulatory controller, which affects the fuel/air ...

K. E. Arystanbaev, A. T. Apsemetov

2014-04-01T23:59:59.000Z

403

A method for carbon oxide concentration evaluation in high-temperature combustion processes  

Science Journals Connector (OSTI)

A method for evaluating carbon oxide concentration in high-temperature combustion processes is presented. The paper offers an optimizing control problem for fuel combustion process using a stabilizing regulatory ...

K. E. Arystanbaev; A. T. Apsemetov

2014-04-01T23:59:59.000Z

404

Surface Chemistry of 2-Propanol on TiO2(110): Low and High Temperature...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Chemistry of 2-Propanol on TiO2(110): Low and High Temperature Dehydration, Isotope Effects, and Influence of Local Surface Chemistry of 2-Propanol on TiO2(110): Low and High...

405

Experimental Analysis of Water Based Drilling Fluid Aging Processes at High Temperature and High Pressure Conditions  

E-Print Network [OSTI]

! ! EXPERIMENTAL ANALYSIS OF WATER BASED DRILLING FLUID AGING PROCESSES AT HIGH TEMPERATURE AND HIGH PRESSURE CONDITIONS A Thesis by BRANDON SCOTT ZIGMOND Submitted to the Office of Graduate Studies of Texas A&M University... Temperature and High Pressure Conditions Copyright 2012 Brandon Scott Zigmond ! ! EXPERIMENTAL ANALYSIS OF WATER BASED DRILLING FLUID AGING PROCESSES AT HIGH TEMPERATURE AND HIGH PRESSURE CONDITIONS A Thesis by BRANDON SCOTT ZIGMOND Submitted...

Zigmond, Brandon

2012-10-19T23:59:59.000Z

406

Temperature dependence of the gaps of high-temperature superconductors in the Fermi-arc region  

Science Journals Connector (OSTI)

It is shown how in a high-temperature superconductor, the length of the Fermi arc can be obtained from the doping dependence of the pseudogap and the superconducting gap. In the momentum region spanned by the Fermi arc, the pseudogap temperature dependence follows that of the superconducting gap. The close interconnection of the two gaps suggests that they are both an essential part of the high-temperature superconductivity.

S. Hüfner and F. Müller

2008-07-23T23:59:59.000Z

407

Effect of high temperature on fruit set of selected genotypes of Lycopersicon esculentum mill.  

E-Print Network [OSTI]

EFFECT OF HIGH TEMPERATURE ON FRUIT SET OF SELECTED GENOTYPES OF LYCOPERSICON ESCULENTUM MILL. A Thesis by ROBERT KEVAN BARRINGER Submitted to the Graduate College of Texas A&M University in partial fullfillment of the requirements... for the degree of MASTER OF SCIENCE December 1982 Major Subject: Horticulture EFFECT OF HIGH TEMPERATURE ON FRUIT SET OF SELECTED GENOTYPES OF LYCOPERSICON ESCULENTUM MILL. A Thes(s by ROBERT KEVAN BARRINGER Approved as to style and content by: Chalrma...

Barringer, Robert Kevan

1982-01-01T23:59:59.000Z

408

Full-length high-temperature severe fuel damage test No. 2. Final safety analysis  

SciTech Connect (OSTI)

Hazardous conditions associated with performing the Full-Length High- Temperature (FLHT). Severe Fuel Damage Test No. 2 experiment have been analyzed. Major hazards that could cause harm or damage are (1) radioactive fission products, (2) radiation fields, (3) reactivity changes, (4) hydrogen generation, (5) materials at high temperature, (6) steam explosion, and (7) steam pressure pulse. As a result of this analysis, it is concluded that with proper precautions the FLHT- 2 test can be safely conducted.

Hesson, G.M.; Lombardo, N.J.; Pilger, J.P.; Rausch, W.N.; King, L.L.; Hurley, D.E.; Parchen, L.J.; Panisko, F.E.

1993-09-01T23:59:59.000Z

409

Development of high-temperature heat exchanger for hydrogen combustion turbine system  

SciTech Connect (OSTI)

New Rankine Cycle and Topping Regenerative Cycle are representative 500MW power generation systems for a hydrogen combustion turbine (HCT). The energy efficiency based on HHV of these is expected to be over 60% because the inlet temperature of turbine can be increased to 1,970K. These systems comprise various heat exchangers. Especially, the development of high temperature heat exchanger dealing with the high temperature and pressure steam is very important to realize the hydrogen combustion turbine system. The high-temperature heat exchanger of New Rankine Cycle is a supercritical heat recovery steam generator operating at pressure of 36MPa. This heat exchanger is heated by steam at temperature of 1,390K. On the other hand, Topping Regenerative Cycle has two high-temperature heat exchangers. One is a regenerator operating at pressure of 37MPa. The other is a regenerator operating at pressure of 5MPa. Both regenerators are heated by steam at temperature of 1,030K. The following are the principal development subject of high-temperature heat exchanger: (1) Improving the heat transfer characteristics to achieve the compact heat exchanger, and (2) Planning the heat exchanger structure suitable for the high thermal stress. To improve a heat transfer characteristic of the high-temperature heat exchangers, a parameter survey is conducted to optimize a tube arrangement and a fin configuration on tube outside and/or inside. The heat transfer areas are minimized through using the tubes with an extended heat transfer surface on both sides of a tube. Structural integrity is also estimated by conducting a structural analysis for the critical parts of the high-temperature heat exchangers.

Takakuwa, Akihiro; Mochida, Yoshio

1999-07-01T23:59:59.000Z

410

Peculiarities of the current-voltage characteristics of a Josephson medium in a YBCO high-temperature superconductor  

Science Journals Connector (OSTI)

The influence of a weak magnetic field (H high-temperature superconductor (HTSC) near the superconducting transitio...

M. A. Vasyutin

2013-12-01T23:59:59.000Z

411

Study on the Application of High Temperature Heat Pump to Recover Waste Heat of Marine Diesel Engine  

Science Journals Connector (OSTI)

Being an energy-saving equipment with great development potential, high temperature heat pump is becoming one of the research hotspots in recent years. However, there is little research about the application of high temperature heat pump on ships as ... Keywords: marine diesel engine, cooling water, waste heat recovery, high temperature heat pump

Shi-jie Liu; Wu Chen; Zhen-xiong Cai; Chao-yu Zheng

2009-10-01T23:59:59.000Z

412

An overview of the geology and secondary mineralogy of the high temperature  

Open Energy Info (EERE)

An overview of the geology and secondary mineralogy of the high temperature An overview of the geology and secondary mineralogy of the high temperature geothermal system in Dixie Valley, Nevada Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: An overview of the geology and secondary mineralogy of the high temperature geothermal system in Dixie Valley, Nevada Abstract Lithologic units encountered in the Dixie Valleygeothermalfield range from Triassic marine sediments toRecent basin-filling sediments. Structural features affectingthe location of the geothermal activity include Mesozoicthrusting. late Tertiary normal faulting andQuaternary to Recent normal faulting. The hydrothermalmineral suite is variable, due in part to rock-gasreactions. Author A. F. Waibel Published Journal Geothermal Resources Council Transactions, 1987

413

R&D Plan for the High Temperature Membrane Working Group  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Plan for the Plan for the High Temperature Membrane Working Group Introduction/Background The High Temperature Membrane Working Group was established to provide a forum for greater interaction in the effort to develop high temperature membranes for PEM fuel cells. The goal of this effort is particularly challenging and requires significant fundamental research and development. The Working Group meets twice a year (immediately before or after the Electrochemical Society meeting) and includes universities, national labs, small business and industry and is open to any interested individual/organization. The first meeting was in October, 2000. Working Group members are listed in Appendix A. This plan was developed to guide the R&D activities of the Working Group. The

414

Active Fault Controls At High-Temperature Geothermal Sites- Prospecting For  

Open Energy Info (EERE)

Page Page Edit History Facebook icon Twitter icon » Active Fault Controls At High-Temperature Geothermal Sites- Prospecting For New Faults Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Paper: Active Fault Controls At High-Temperature Geothermal Sites- Prospecting For New Faults Details Activities (1) Areas (1) Regions (0) Abstract: Our previous studies found spatial associations between seismically active faults and high-temperature geothermal resources in the western Basin and Range, suggesting that recency of fault movement may be a useful criterion for resource exploration. We have developed a simple conceptual model in which recently active (Holocene) faults are preferred conduits for migration of thermal water from deep crustal depths, and we

415

Integrated Process Configuration for High-Temperature Sulfur Mitigation during Biomass Conversion via Indirect Gasification  

SciTech Connect (OSTI)

Sulfur present in biomass often causes catalyst deactivation during downstream operations after gasification. Early removal of sulfur from the syngas stream post-gasification is possible via process rearrangements and can be beneficial for maintaining a low-sulfur environment for all downstream operations. High-temperature sulfur sorbents have superior performance and capacity under drier syngas conditions. The reconfigured process discussed in this paper is comprised of indirect biomass gasification using dry recycled gas from downstream operations, which produces a drier syngas stream and, consequently, more-efficient sulfur removal at high temperatures using regenerable sorbents. A combination of experimental results from NREL's fluidizable Ni-based reforming catalyst, fluidizable Mn-based sulfur sorbent, and process modeling information show that using a coupled process of dry gasification with high-temperature sulfur removal can improve the performance of Ni-based reforming catalysts significantly.

Dutta. A.; Cheah, S.; Bain, R.; Feik, C.; Magrini-Bair, K.; Phillips, S.

2012-06-20T23:59:59.000Z

416

High-temperature fiber optic cubic-zirconia pressure sensor - article no. 124402  

SciTech Connect (OSTI)

There is a critical need for pressure sensors that can operate reliably at high temperatures in many industrial segments such as in the combustion section of gas turbine engines for both transportation and power generation, coal gasifiers, coal fired boilers, etc. Optical-based sensors are particularly attractive for the measurement of a wide variety of physical and chemical parameters in high-temperature and high-pressure industrial environments due to their small size and immunity to electromagnetic interference. A fiber optic pressure sensor utilizing single-crystal cubic zirconia as the sensing element is reported. The pressure response of this sensor has been measured at temperatures up to 1000{sup o}C. Additional experimental results show that cubic zirconia could be used for pressure sensing at temperatures over 1000{sup o}C. This study demonstrates the feasibility of using a novel cubic-zirconia sensor for pressure measurement at high temperatures.

Peng, W.; Pickrell, G.R.; Wang, A.B. [Virginia Polytechnic Institute & State University, Blacksburg, VA (United States)

2005-12-15T23:59:59.000Z

417

Phononic pairing glue in cuprates and related high-temperature superconductors  

E-Print Network [OSTI]

Along with some other researches we have realised that the true origin of high-temperature superconductivity should be found in the strong Coulomb repulsion combined with a significant electronphonon interaction. Both interactions are strong (on the order of 1 eV) compared with the low Fermi energy of doped carries which makes the conventional BCS-Eliashberg theory inapplicable in cuprates and related doped insulators. Based on our recent analytical and numerical results I argue that high-temperature superconductivity from repulsion is impossible for any strength of the Coulomb interaction. Major steps of our alternative polaronic theory are outlined starting from the generic Hamiltonian with the unscreened (bare) Coulomb and electron-phonon interactions accounting for critical temperatures of high-temperature superconductors without any adjustable parameters.

A. S. Alexandrov

2011-12-16T23:59:59.000Z

418

Method and apparatus for measuring gravitational acceleration utilizing a high temperature superconducting bearing  

DOE Patents [OSTI]

Gravitational acceleration is measured in all spatial dimensions with improved sensitivity by utilizing a high temperature superconducting (HTS) gravimeter. The HTS gravimeter is comprised of a permanent magnet suspended in a spaced relationship from a high temperature superconductor, and a cantilever having a mass at its free end is connected to the permanent magnet at its fixed end. The permanent magnet and superconductor combine to form a bearing platform with extremely low frictional losses, and the rotational displacement of the mass is measured to determine gravitational acceleration. Employing a high temperature superconductor component has the significant advantage of having an operating temperature at or below 77K, whereby cooling may be accomplished with liquid nitrogen.

Hull, John R. (Downers Grove, IL)

2000-01-01T23:59:59.000Z

419

ULTRA-HIGH TEMPERATURE SENSORS BASED ON OPTICAL PROPERTY MODULATION AND VIBRATION-TOLERANT INTERFEROMETRY  

SciTech Connect (OSTI)

The goals of the first six months of this project were to lay the foundations for both the SiC front-end optical chip fabrication as well as the free-space laser beam interferometer designs and preliminary tests. In addition, a Phase I goal was to design and experimentally build the high temperature and pressure infrastructure and test systems that will be used in the next 6 months for proposed sensor experimentation and data processing. All these goals have been achieved and are described in detail in the report. Both design process and diagrams for the mechanical elements as well as the optical systems are provided. In addition, photographs of the fabricated SiC optical chips, the high temperature & pressure test chamber instrument, the optical interferometer, the SiC sample chip holder, and signal processing data are provided. The design and experimentation results are summarized to give positive conclusions on the proposed novel high temperature optical sensor technology.

Nabeel A. Riza

2004-04-01T23:59:59.000Z

420

Understanding Fundamental Material Degradation Processes in High Temperature Aggressive Chemomechanical Environments  

SciTech Connect (OSTI)

The objective of this project is to develop a fundamental understanding of the mechanisms that limit materials durability for very high-temperature applications. Current design limitations are based on material strength and corrosion resistance. This project will characterize the interactions of high-temperature creep, fatigue, and environmental attack in structural metallic alloys of interest for the very high-temperature gas-cooled reactor (VHTR) or Next–Generation Nuclear Plant (NGNP) and for the associated thermo-chemical processing systems for hydrogen generation. Each of these degradation processes presents a major materials design challenge on its own, but in combination, they can act synergistically to rapidly degrade materials and limit component lives. This research and development effort will provide experimental results to characterize creep-fatigue-environment interactions and develop predictive models to define operation limits for high-temperature structural material applications. Researchers will study individually and in combination creep-fatigue-environmental attack processes in Alloys 617, 230, and 800H, as well as in an advanced Ni-Cr oxide dispersion strengthened steel (ODS) system. For comparison, the study will also examine basic degradation processes in nichrome (Ni-20Cr), which is a basis for most high-temperature structural materials, as well as many of the superalloys. These materials are selected to represent primary candidate alloys, one advanced developmental alloy that may have superior high-temperature durability, and one model system on which basic performance and modeling efforts can be based. The research program is presented in four parts, which all complement each other. The first three are primarily experimental in nature, and the last will tie the work together in a coordinated modeling effort. The sections are 1) dynamic creep-fatigue-environment process, 2) subcritical crack processes, 3) dynamic corrosion – crack initiation processes, and 4) modeling.

Stubbins, James; Gewirth, Andrew; Sehitoglu, Huseyin; Sofronis, Petros; Robertson, Ian

2014-01-16T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

High-Temperature Nuclear Reactors for In-Situ Recovery of Oil from Oil Shale  

SciTech Connect (OSTI)

The world is exhausting its supply of crude oil for the production of liquid fuels (gasoline, jet fuel, and diesel). However, the United States has sufficient oil shale deposits to meet our current oil demands for {approx}100 years. Shell Oil Corporation is developing a new potentially cost-effective in-situ process for oil recovery that involves drilling wells into oil shale, using electric heaters to raise the bulk temperature of the oil shale deposit to {approx}370 deg C to initiate chemical reactions that produce light crude oil, and then pumping the oil to the surface. The primary production cost is the cost of high-temperature electrical heating. Because of the low thermal conductivity of oil shale, high-temperature heat is required at the heater wells to obtain the required medium temperatures in the bulk oil shale within an economically practical two to three years. It is proposed to use high-temperature nuclear reactors to provide high-temperature heat to replace the electricity and avoid the factor-of-2 loss in converting high-temperature heat to electricity that is then used to heat oil shale. Nuclear heat is potentially viable because many oil shale deposits are thick (200 to 700 m) and can yield up to 2.5 million barrels of oil per acre, or about 125 million dollars/acre of oil at $50/barrel. The concentrated characteristics of oil-shale deposits make it practical to transfer high-temperature heat over limited distances from a reactor to the oil shale deposits. (author)

Forsberg, Charles W. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831-6165 (United States)

2006-07-01T23:59:59.000Z

422

A Process Model for the Production of Hydrogen Using High Temperature Electrolysis  

SciTech Connect (OSTI)

High temperature electrolysis (HTE) involves the splitting of stream into hydrogen and oxygen at high temperatures. The primary advantage of HTE over conventional low temperature electrolysis is that considerably higher hydrogen production efficiencies can be achieved. Performing the electrolysis process at high temperatures results in more favorable thermodynamics for electrolysis, more efficient production of electricity, and allows direct use of process heat to generate steam. This paper presents the results of process analyses performed to evaluate the hydrogen production efficiencies of an HTE plant coupled to a 600 MWt Modular Helium Reactor (MHR) that supplies both the electricity and process heat needed to drive the process. The MHR operates with a coolant outlet temperature of 950 C. Approximately 87% of the high-temperature heat is used to generate electricity at high efficiency using a direct, Brayton-cycle power conversion system. The remaining high-temperature heat is used to generate a superheated steam / hydrogen mixture that is supplied to the electrolyzers. The analyses were performed using the HYSYS process modeling software. The model used to perform the analyses consisted of three loops; a primary high temperature helium loop, a secondary helium loop and the HTE process loop. The detailed model included realistic representations of all major components in the system, including pumps, compressors, heat exchange equipment, and the electrolysis stack. The design of the hydrogen production process loop also included a steam-sweep gas system to remove oxygen from the electrolysis stack so that it can be recovered and used for other applications. Results of the process analyses showed that hydrogen production efficiencies in the range of 45% to 50% are achievable with this system.

M. G. Mc Kellar; E. A. Harvego; M. Richards; A. Shenoy

2006-07-01T23:59:59.000Z

423

SciTech Connect: "high temperature superconductivity"  

Office of Scientific and Technical Information (OSTI)

high temperature superconductivity" Find high temperature superconductivity" Find How should I search Scitech Connect ... Basic or Advanced? Basic Search Advanced × Advanced Search Options Full Text: Bibliographic Data: Creator / Author: Name Name ORCID Title: Subject: Identifier Numbers: Research Org.: Sponsoring Org.: Site: All Alaska Power Administration, Juneau, Alaska (United States) Albany Research Center (ARC), Albany, OR (United States) Albuquerque Complex - NNSA Albuquerque Operations Office, Albuquerque, NM (United States) Amarillo National Resource Center for Plutonium, Amarillo, TX (United States) Ames Laboratory (AMES), Ames, IA (United States) Argonne National Laboratory (ANL), Argonne, IL (United States) Argonne National Laboratory-Advanced Photon Source (United States) Atlanta Regional Office,

424

Method for fabricating wrought components for high-temperature gas-cooled reactors and product  

DOE Patents [OSTI]

A method and alloys for fabricating wrought components of a high-temperature gas-cooled reactor are disclosed. These wrought, nickel-based alloys, which exhibit strength and excellent resistance to carburization at elevated temperatures, include aluminum and titanium in amounts and ratios to promote the growth of carburization resistant films while preserving the wrought character of the alloys. These alloys also include substantial amounts of molybdenum and/or tungsten as solid-solution strengtheners. Chromium may be included in concentrations less than 10% to assist in fabrication. Minor amounts of carbon and one or more carbide-forming metals also contribute to high-temperature strength.

Thompson, Larry D. (San Diego, CA); Johnson, Jr., William R. (San Diego, CA)

1985-01-01T23:59:59.000Z

425

Plasma etching of cavities into diamond anvils for experiments at high pressures and high temperatures  

SciTech Connect (OSTI)

We describe a method for precisely etching small cavities into the culets of diamond anvils for the purpose of providing thermal insulation for samples in experiments at high pressures and high temperatures. The cavities were fabricated using highly directional oxygen plasma to reactively etch into the diamond surface. The lateral extent of the etch was precisely controlled to micron accuracy by etching the diamond through a lithographically fabricated tungsten mask. The performance of the etched cavities in high-temperature experiments in which the samples were either laser heated or electrically heated is discussed.

Weir, S.T.; Cynn, H.; Falabella, S.; Evans, W.J.; Aracne-Ruddle, C.; Farber, D.; Vohra, Y.K. (LLNL); (UAB)

2012-10-23T23:59:59.000Z

426

Temperature dependence of the lower critical field and strong pinning in high-temperature superconductors  

Science Journals Connector (OSTI)

We show, within the framework of the Ginzburg-Landau theory, that both the conventional and the anomalous temperature dependence of the lower critical field observed in high-temperature superconductors may result from the flux penetration through a set of separated microdefects. Microdefects modeled by normal layers with proximity-induced superconductivity can produce drastic enhancement of the lower critical field at low temperatures and can provide strong-pinning centers. The pinning interaction between an isolated vortex and the normal layer is primarily magnetic at high temperatures. At low temperatures, magnetic interaction is reduced, due to the increase of the normal-layer coherence length.

Dragomir Davidovi? and Ljiljana Dobrosavljevi?-Gruji?

1991-02-01T23:59:59.000Z

427

Secondary heat exchanger design and comparison for advanced high temperature reactor  

SciTech Connect (OSTI)

Next generation nuclear reactors such as the advanced high temperature reactor (AHTR) are designed to increase energy efficiency in the production of electricity and provide high temperature heat for industrial processes. The efficient transfer of energy for industrial applications depends on the ability to incorporate effective heat exchangers between the nuclear heat transport system and the industrial process heat transport system. This study considers two different types of heat exchangers - helical coiled heat exchanger and printed circuit heat exchanger - as possible options for the AHTR secondary heat exchangers with distributed load analysis and comparison. Comparison is provided for all different cases along with challenges and recommendations. (authors)

Sabharwall, P. [Idaho National Laboratory, Idaho Falls, ID 83415-3860 (United States); Kim, E. S. [Seoul National Univ., P.O. Box 1625, Idaho Falls, ID 83415-3860 (United States); Siahpush, A.; McKellar, M.; Patterson, M. [Idaho National Laboratory, Idaho Falls, ID 83415-3860 (United States)

2012-07-01T23:59:59.000Z

428

3D CFD Model of High Temperature H2O/CO2 Co-electrolysis  

SciTech Connect (OSTI)

3D CFD Model of High Temperature H2O/CO2 Co-Electrolysis Grant Hawkes1, James O’Brien1, Carl Stoots1, Stephen Herring1 Joe Hartvigsen2 1 Idaho National Laboratory, Idaho Falls, Idaho, grant.hawkes@inl.gov 2 Ceramatec Inc, Salt Lake City, Utah INTRODUCTION A three-dimensional computational fluid dynamics (CFD) model has been created to model high temperature co-electrolysis of steam and carbon dioxide in a planar solid oxide electrolyzer (SOE) using solid oxide fuel cell technology. A research program is under way at the Idaho National Laboratory (INL) to simultaneously address the research and scale-up issues associated with the implementation of planar solid-oxide electrolysis cell technology for syn-gas production from CO2 and steam. Various runs have been performed under different run conditions to help assess the performance of the SOE. This paper presents CFD results of this model compared with experimental results. The Idaho National Laboratory (INL), in conjunction with Ceramatec Inc. (Salt Lake City, USA) has been researching for several years the use of solid-oxide fuel cell technology to electrolyze steam for large-scale nuclear-powered hydrogen production. Now, an experimental research project is underway at the INL to produce syngas by simultaneously electrolyzing at high-temperature steam and carbon dioxide (CO2) using solid oxide fuel cell technology. A strong interest exists in the large-scale production of syn-gas from CO2 and steam to be reformed into a usable transportation fuel. If biomass is used as the carbon source, the overall process is climate neutral. Consequently, there is a high level of interest in production of syn-gas from CO2 and steam electrolysis. With the price of oil currently around $60 / barrel, synthetically-derived hydrocarbon fuels (synfuels) have become economical. Synfuels are typically produced from syngas – hydrogen (H2) and carbon monoxide (CO) -- using the Fischer-Tropsch process, discovered by Germany before World War II. High-temperature nuclear reactors have the potential for substantially increasing the efficiency of syn-gas production from CO2 and water, with no consumption of fossil fuels, and no production of greenhouse gases. Thermal CO2-splitting and water splitting for syn-gas production can be accomplished via high-temperature electrolysis, using high-temperature nuclear process heat and electricity. A high-temperature advanced nuclear reactor coupled with a high-efficiency high-temperature electrolyzer could achieve a competitive thermal-to-syn-gas conversion efficiency of 45 to 55%.

Grant Hawkes; James O'Brien; Carl Stoots; Stephen Herring; Joe Hartvigsen

2007-06-01T23:59:59.000Z

429

Process for introducing electrical conductivity into high-temperature polymeric materials  

DOE Patents [OSTI]

High-temperature electrically conducting polymers. The in situ reactions: AgNO.sub.3 +RCHO.fwdarw.Ag.degree.+RCOOH and R.sub.3 M.fwdarw.M.degree.+3R, where M=Au or Pt have been found to introduce either substantial bulk or surface conductivity in high-temperature polymers. The reactions involving the R.sub.3 M were caused to proceed thermally suggesting the possibility of using laser means for initiating such reactions in selected areas or volumes of the polymeric materials. The polymers successfully investigated to date are polyphenylquinoxaline, polytolylquinoxaline, polyquinoline, polythiazole, and pyrrone.

Liepins, Raimond (Los Alamos, NM); Jorgensen, Betty S. (Jemez Springs, NM); Liepins, Leila Z. (Los Alamos, NM)

1993-01-01T23:59:59.000Z

430

Wear damage resulting from sliding impact kinematics in pressurized high temperature water: energetical and  

E-Print Network [OSTI]

1 Wear damage resulting from sliding impact kinematics in pressurized high temperature water and Cecile Langlade2,3 1 FRAMATOME-ANP Technical Center, Avenue B. Marcet, Porte Magenta, 71200 Le Creusot.bec@ec-lyon.fr Abstract Specific wear of Rod Cluster Control Assemblies (RCCA) in Pressurized Water nuclear Reactors (PWR

Paris-Sud XI, Université de

431

A Review of High-Temperature Geothermal Developments in the Northern...  

Open Energy Info (EERE)

Intensive geothermal exploration i n the northernBasin.and Range province has r e s u l t e d i n thethe discovery of nine high-temperature (>ZOO"C)geothermal r e s e r v o i r...

432

High-temperature deformation in the Neoproterozoic transpressional Ribeira belt, southeast Brazil  

E-Print Network [OSTI]

High-temperature deformation in the Neoproterozoic transpressional Ribeira belt, southeast Brazil^ncias da Universidade de Sa~o Paulo, Rua do Lago 562, Cep: 05508-080, Sa~o Paulo, SP, Brazil b Laboratoire Geologia, Universidade Federal de Ouro Preto, 35400-000, Ouro Pre^to, MG, Brazil Received 5 April 2001

Bascou, JĂ©rĂŽme

433

Method of and apparatus for removing silicon from a high temperature sodium coolant  

DOE Patents [OSTI]

A method of and system for removing silicon from a high temperature liquid sodium coolant system for a nuclear reactor. The sodium is cooled to a temperature below the silicon saturation temperature and retained at such reduced temperature while inducing high turbulence into the sodium flow for promoting precipitation of silicon compounds and ultimate separation of silicon compound particles from the liquid sodium.

Yunker, Wayne H. (Richland, WA); Christiansen, David W. (Kennewick, WA)

1987-01-01T23:59:59.000Z

434

Integrated Process Configuration for High-Temperature Sulfur Mitigation during Biomass Conversion via Indirect Gasification  

Science Journals Connector (OSTI)

Integrated Process Configuration for High-Temperature Sulfur Mitigation during Biomass Conversion via Indirect Gasification ... National Bioenergy Center, National Renewable Energy Laboratory, 1617 Cole Blvd., Golden, Colorado 80401, United States ... Similar activation energies (9-10 kcal/mol) were measured for ZnO and Zn-Ti-O sulfidation. ...

Abhijit Dutta; Singfoong Cheah; Richard Bain; Calvin Feik; Kim Magrini-Bair; Steven Phillips

2012-05-23T23:59:59.000Z

435

DEVELOPMENT OF HIGH TEMPERATURE TARGETS AND ION SOURCES FOR ONLINE RADIOACTIVE ISOTOPE PRODUCTION  

E-Print Network [OSTI]

and refractory metal carbide targets up to 2800--3000°K and up to 2500°K for uranium carbide targets. Tests of Ta refractory metal and refractory metal carbide targets 2.1. Off­line tests of a high temperature tantalum temperature uranium carbide targets of different density were carried out. High yields of Rb and Cs neutron

Titov, Anatoly

436

Neutron and X-ray experiments at high temperature P. Aldebert (*)  

E-Print Network [OSTI]

649 Neutron and X-ray experiments at high temperature P. Aldebert (*) LA 302, E.N.S.C.P., 11, rue récemment celle des neutrons sont devenues des sondes puissantes propres à fournir des infor- mations'échantillon avec son environnement, en fait l'atmosphÚre ambiante et le support de l'échantillon. Les neutrons

Boyer, Edmond

437

Brief Communication High temperature pulses decrease indirect chilling injury and elevate ATP levels  

E-Print Network [OSTI]

Brief Communication High temperature pulses decrease indirect chilling injury and elevate ATP: Received 20 December 2009 Accepted 8 March 2010 Available online 15 March 2010 Keywords: ATP Energy supply by determining survival rates and ATP levels for flies that had undergone continuous long-term exposure at 0 °C

Lee Jr., Richard E.

438

Peculiarities of Rapid Pyrolysis of Biomass Covering Medium- and High-Temperature Ranges  

Science Journals Connector (OSTI)

Peculiarities of Rapid Pyrolysis of Biomass Covering Medium- and High-Temperature Ranges ... It is considered that rapid pyrolysis is the first step in both gasification and combustion, which occurs at the same temperature of gasification or combustion in an industrial gasifier or boiler. ...

Yan Zhang; Shiro Kajitani; Masami Ashizawa; Kouichi Miura

2006-10-17T23:59:59.000Z

439

Production of Carbon from Carbon Dioxide with Iron Oxides and High-Temperature Solar Energy  

Science Journals Connector (OSTI)

Production of Carbon from Carbon Dioxide with Iron Oxides and High-Temperature Solar Energy ... 2 Since it is the major oxidation product from all hydrocarbon combustion processes, its presence permeates nearly every sector of the world economy. ... Thus, CO2 recycling and utilization seems to be a fundamental task from both an ecological and economical point of view. ...

K. Ehrensberger; R. Palumbo; C. Larson; A. Steinfeld

1997-03-03T23:59:59.000Z

440

DEVELOPMENT OF HIGH PERFORMANCE BS-PT BASED PIEZOELECTRIC TRANSDUCERS FOR HIGH-TEMPERATURE  

E-Print Network [OSTI]

-TEMPERATURE APPLICATIONS Yu-Hung Li1 , Sang Jong Kim2 , Nathan Salowitz2 , Fu-Kuo Chang2 1 Department of Materials Science processes in industries like aerospace. However, similar ultrasonic SHM techniques for high downhole casings). Recent research in high-temperature piezoelectric materials has facilitated

Boyer, Edmond

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

High temperature furnaces for small and large angle neutron scattering of disordered materials  

E-Print Network [OSTI]

725 High temperature furnaces for small and large angle neutron scattering of disordered materials and small angle neutron scattering (SANS) experiments respectively. They are vacuum furnaces with a thin maintained in a tantalum box. In a neutron beam, the furnaces produce a very low scattering level (without

Boyer, Edmond

442

Design of a High Temperature Small Particle Solar Receiver for Powering a Gas Turbine Engine  

E-Print Network [OSTI]

Design of a High Temperature Small Particle Solar Receiver for Powering a Gas Turbine Engine Dr. Fletcher Miller SDSU Department of Mechanical Engineering Abstract Solar thermal power for electricity for the California desert and in other appro- priate regions worldwide. Current technology relies on steam Rankine

Ponce, V. Miguel

443

Oxidation of carbon fiber surfaces for use as reinforcement in high-temperature cementitious material systems  

DOE Patents [OSTI]

The interfacial bond characteristics between carbon fiber and a cement matrix, in high temperature fiber-reinforced cementitious composite systems, can be improved by the oxidative treatment of the fiber surfaces. Compositions and the process for producing the compositions are disclosed. 2 figs.

Sugama, Toshifumi.

1990-05-22T23:59:59.000Z

444

Oxidation of carbon fiber surfaces for use as reinforcement in high-temperature cementitious material systems  

DOE Patents [OSTI]

The interfacial bond characteristics between carbon fiber and a cement matrix, in high temperature fiber-reinforced cementitious composite systems, can be improved by the oxidative treatment of the fiber surfaces. Compositions and the process for producing the compositions are disclosed.

Sugama, Toshifumi (Mastic Beach, NY)

1990-01-01T23:59:59.000Z

445

Copper modified austenitic stainless steel alloys with improved high temperature creep resistance  

DOE Patents [OSTI]

An improved austenitic stainless steel that incorporates copper into a base Fe-Ni-Cr alloy having minor alloying substituents of Mo, Mn, Si, T, Nb, V, C, N, P, B which exhibits significant improvement in high temperature creep resistance over previous steels. 3 figs.

Swindeman, R.W.; Maziasz, P.J.

1987-04-28T23:59:59.000Z

446

"Ceramics and high-temperature composites, silicides" Oxidation of Stainless Steel Powder  

E-Print Network [OSTI]

: Powder, stainless steel, oxidation INTRODUCTION Ceramic matrix composites dispersed with metal particles"Ceramics and high-temperature composites, silicides" CHTC9 Oxidation of Stainless Steel Powder. To understand the corrosion behavior of a model 304L(p)-ZrO2(s) composite, a 304L stainless steel powder has

Paris-Sud XI, Université de

447

A simple, inexpensive device for measuring the critical temperature of a high-temperature superconductor  

Science Journals Connector (OSTI)

A simple, inexpensive device for measuring the critical temperature of a high-temperature superconductor ... This note describes a simple, inexpensive method of measuring the temperature at which the Meissner effect exists in a disk of YBa2Cu3O7-x. ...

David B. Green; Dijon Douphner; Bennett Hutchinson

1992-01-01T23:59:59.000Z

448

Electrical conductivity of wadsleyite at high temperatures and high pressures Lidong Dai a,b  

E-Print Network [OSTI]

Electrical conductivity of wadsleyite at high temperatures and high pressures Lidong Dai a,b , Shun 2009 Editor: L. Stixrude Keywords: electrical conductivity wadsleyite oxygen fugacity frequency water The electrical conductivity of wadsleyite aggregates has been determined under the broad range of thermodynamic

449

Results Of Recent High Temperature Co-Electrolysis Studies At The Idaho National Laboratory  

SciTech Connect (OSTI)

For the past several years, the Idaho National Laboratory and Ceramatec, Inc. have been studying the feasibility of high temperature solid oxide electrolysis for large-scale, nuclear-powered hydrogen production. Parallel to this effort, the INL and Ceramatec have been researching high temperature solid oxide co-electrolysis of steam/CO2 mixtures to produce syngas, the raw material for synthetic fuels production. When powered by nuclear energy, high temperature co-electrolysis offers a carbon-neutral means of syngas production while consuming CO2. The INL has been conducting experiments to characterize the electrochemical performance of co-electrolysis, as well as validate INL-developed computer models. An inline methanation reactor has also been tested to study direct methane production from co-electrolysis products. Testing to date indicate that high temperature steam electrolysis cells perform equally well under co-electrolysis conditions. Process model predictions compare well with measurements for outlet product compositions. The process appears to be a promising technique for large-scale syngas production.

C. M. Stoots; James E. O'Brien; Joseph J. Hartvigsen

2007-11-01T23:59:59.000Z

450

Design and Evaluation of a High Temperature Burner Duct Recuperator System  

E-Print Network [OSTI]

"The Babcock & Wilcox Company (B&W) has completed a program to design, construct, install, and field test a ceramic-based high-temperature burner-duct-recuperator (HTBDR) in an industrial setting. The unit was capable of operating in corrosive, high...

Parks, W. P.; DeBellis, C. L.; Kneidel, K.

451

High temperature thermoelectric characterization of III-V semiconductor thin films by oxide bonding  

E-Print Network [OSTI]

energy conversion, and other high temperature applications.[1-5] Since the efficiency of those energy conversion applications relies heavily on the carrier transport properties of the materials used, it is very by Molecular Beam Epitaxy (MBE) has demonstrated its usefulness in thermoelectric energy conversion

Bowers, John

452

High-Temperature Thermoelectric Characterization of IIIV Semiconductor Thin Films by Oxide Bonding  

E-Print Network [OSTI]

energy conversion, and other high-temperature applications.1­4 Since the efficiency of these energy conversion applications relies heavily on the carrier transport properties of the materials used, it is very by molecular beam epitaxy (MBE) has demonstrated its useful- ness in thermoelectric energy conversion

453

Graphene, a material for high temperature devices intrinsic carrier density, carrier  

E-Print Network [OSTI]

Graphene, a material for high temperature devices ­ intrinsic carrier density, carrier drift 3.87 3 106 cm22 K22 ?T2 ), carrier drift velocity, and G mode phonon energy of graphene devices and their temperature dependencies up to 2400 K. Our results show intrinsic carrier density of graphene is an order

Wang, Wei Hua

454

HIGH TEMPERATURE SULFIDATION BEHAVIOR OF LOW Al IRON-ALUMINUM COMPOSITIONS  

E-Print Network [OSTI]

HIGH TEMPERATURE SULFIDATION BEHAVIOR OF LOW Al IRON-ALUMINUM COMPOSITIONS S.W. Banovic, J.N. Du (Received January 5, 1998) (Accepted March 23, 1998) Introduction Iron-aluminum weld overlay coatings, the application of iron-aluminum alloys is currently limited due to hydrogen cracking susceptibility subsequent

DuPont, John N.

455

Towards an airborne high temperature SiC inverter Dominique Bergogne, Herve Morel,  

E-Print Network [OSTI]

profile is briefly described in table I. b) A step by step work: Work started with first generation JFET for high temperature operation of power converters. The paper describes the laboratory step by step work' to 'full three phase power stage' tested up to 250C, including capacitor. Device samples are characterized

Paris-Sud XI, Université de

456

Integration of High-Temperature Gas-Cooled Reactors into Industrial Process Applications  

SciTech Connect (OSTI)

This report is a summary of analyses performed by the NGNP project to determine whether it is technically and economically feasible to integrate high temperature gas cooled reactor (HTGR) technology into industrial processes. To avoid an overly optimistic environmental and economic baseline for comparing nuclear integrated and conventional processes, a conservative approach was used for the assumptions and calculations.

Lee Nelson

2011-09-01T23:59:59.000Z

457

Detecting and modeling cement failure in high pressure/ high temperature wells using finite-element method  

E-Print Network [OSTI]

. In the event that high-pressure and high-temperature (HPHT) conditions are encountered, we must attempt to achieve permeability in the set cement to prevent gas migration and to prevent any other fluid passing through to collapse the entire structure. Therefore...

Shahri, Mehdi Abbaszadeh

2006-04-12T23:59:59.000Z

458

Development of a High-Temperature Diagnostics-While-Drilling Tool  

Broader source: Energy.gov [DOE]

This report documents work performed in the second phase of the Diagnostics-While-Drilling (DWD) project in which a high-temperature (HT) version of the phase 1 low-temperature (LT) proof-of-concept (POC) DWD tool was built and tested. Descriptions of the design, fabrication and field testing of the HT tool are provided.

459

High-Temperature Superconducting Cable Testing Gregory S. Boebinger, National High Magnetic Field Laboratory  

E-Print Network [OSTI]

High-Temperature Superconducting Cable Testing Gregory S. Boebinger, National High Magnetic Field-Temperature Superconducting (HTS) Cables are desirable for application in large high-field magnets (>20 T), especially when). Of the three HTS magnet cable concepts emerging, the Conductor On Round Core was the first that was tested

Weston, Ken

460

Catalytically Assisted Self-Propagating High-Temperature Synthesis of Tantalum Carbide Powders  

E-Print Network [OSTI]

) that are otherwise difficult to produce (e.g., transition metal/borides, carbides, and nitrides).1,2 Many earlierCatalytically Assisted Self-Propagating High-Temperature Synthesis of Tantalum Carbide Powders Troy/carbon/tantalum carbide combustion synthesis system has been examined to determine the effects of transport agents

Wooldridge, Margaret S.

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Dimensional reduction and quantum-to-classical reduction at high temperatures  

Science Journals Connector (OSTI)

We discuss the relation between dimensional reduction in quantum field theories at finite temperature and a familiar quantum-mechanical phenomenon that quantum effects become negligible at high temperatures. Fermi and Bose fields are compared in this respect. We show that decoupling of fermions from the dimensionally reduced theory can be related to the nonexistence of classical statistics for a Fermi field.

M. A. Stephanov

1995-09-15T23:59:59.000Z

462

An Experimental Test Facility to Support Development of the Fluoride Salt Cooled High Temperature Reactor  

SciTech Connect (OSTI)

The need for high-temperature (greater than 600 C) energy exchange and delivery systems is significantly increasing as the world strives to improve energy efficiency and develop alternatives to petroleum-based fuels. Liquid fluoride salts are one of the few energy transport fluids that have the capability of operating at high temperatures in combination with low system pressures. The Fluoride Salt-Cooled High-Temperature Reactor design uses fluoride salt to remove core heat and interface with a power conversion system. Although a significant amount of experimentation has been performed with these salts, specific aspects of this reactor concept will require experimental confirmation during the development process. The experimental facility described here has been constructed to support the development of the Fluoride Salt Cooled High Temperature Reactor concept. The facility is capable of operating at up to 700 C and incorporates a centrifugal pump to circulate FLiNaK salt through a removable test section. A unique inductive heating technique is used to apply heat to the test section, allowing heat transfer testing to be performed. An air-cooled heat exchanger removes added heat. Supporting loop infrastructure includes a pressure control system; trace heating system; and a complement of instrumentation to measure salt flow, temperatures, and pressures around the loop. The initial experiment is aimed at measuring fluoride salt heat transfer inside a heated pebble bed similar to that used for the core of the pebble bed advanced high-temperature reactor. This document describes the details of the loop design, auxiliary systems used to support the facility, the inductive heating system, and facility capabilities.

Yoder Jr, Graydon L [ORNL] [ORNL; Aaron, Adam M [ORNL] [ORNL; Cunningham, Richard Burns [University of Tennessee, Knoxville (UTK)] [University of Tennessee, Knoxville (UTK); Fugate, David L [ORNL] [ORNL; Holcomb, David Eugene [ORNL] [ORNL; Kisner, Roger A [ORNL] [ORNL; Peretz, Fred J [ORNL] [ORNL; Robb, Kevin R [ORNL] [ORNL; Wilgen, John B [ORNL] [ORNL; Wilson, Dane F [ORNL] [ORNL

2014-01-01T23:59:59.000Z

463

ULTRA-HIGH TEMPERATURE SENSORS BASED ON OPTICAL PROPERTY MODULATION AND VIBRATION-TOLERANT INTERFEROMETRY  

SciTech Connect (OSTI)

The goals of the first six months of this project were to lay the foundations for both the SiC front-end optical chip fabrication as well as the free-space laser beam interferometer designs and preliminary tests. In addition, a Phase I goal was to design and experimentally build the high temperature and pressure infrastructure and test systems that will be used in the next 6 months for proposed sensor experimentation and data processing. All these goals have been achieved and are described in detail in the report. Both design process and diagrams for the mechanical elements as well as the optical systems are provided. In addition, photographs of the fabricated SiC optical chips, the high temperature & pressure test chamber instrument, the optical interferometer, the SiC sample chip holder, and signal processing data are provided. The design and experimentation results are summarized to give positive conclusions on the proposed novel high temperature optical sensor technology. The goals of the second six months of this project were to conduct high temperature sensing tests using the test chamber and optical sensing instrument designs developed in the first part of the project. In addition, a Phase I goal was to develop the basic processing theory and physics for the proposed first sensor experimentation and data processing. All these goals have been achieved and are described in detail. Both optical experimental design process and sensed temperature are provided. In addition, photographs of the fabricated SiC optical chips after deployment in the high temperature test chamber are shown from a material study point-of-view.

Nabeel A. Riza

2004-11-10T23:59:59.000Z

464

Encapsulation of copper-based phase change materials for high temperature thermal energy storage  

Science Journals Connector (OSTI)

Abstract Worldwide attention has been paid to high temperature phase change materials (PCMs) utilized in latent heat storage systems such as solar thermal power generation or industrial waste heat recovery. Current high temperature \\{PCMs\\} on basis of molten salts are suffering from inherent low thermal conductivity, which is detrimental to heat release rate and systematically thermal efficiency. Metal materials, always possessing ultrahigh thermal conductivity and satisfied heat fusion, are highly suitable as PCMs. However, the development of metal-based \\{PCMs\\} must overcome the package problem, namely, packing active, high temperature liquid metal into durable container. In this paper, copper capsules coated with refractory metallic shells were proposed as a novel metal PCM, which could work at temperature up to 1000 °C. Copper spheres with diameter of millimeters were encapsulated with a thick chromium–nickel bilayer by a novel chromium periodic-barrel electroplating method and nickel barrel-plating method. The latent heat density of as-prepared capsules is up to 75% of the theoretical value (about 71 J/g) at the melting temperature of 1077 °C and the thermal resistance of chromium–nickel layer is 8.27Ś10?6 m2 k/w. Particularly, copper capsules could endure 1000 charge–discharge thermal cycles from 1050 °C to 1150 °C without any leakage. The structure investigations reveal the excellent oxidation resistance of capsules and good stability between copper and chromium–nickel layer, even after long-term charge–discharge cycles. The results demonstrate that as-prepared copper capsules are applicable as high temperature \\{PCMs\\} which can facilitate high temperature thermal energy storage systems.

Guocai Zhang; Jianqiang Li; Yunfa Chen; Heng Xiang; Bingqian Ma; Zhe Xu; Xiaoguang Ma

2014-01-01T23:59:59.000Z

465

Physics based analytical modelling of Gallium Nitride(GaN) MESFET considering different ion implantation energy with high temperature annealing.  

E-Print Network [OSTI]

??A physics based analytical model of ion implanted GaN MESFET has been presented considering high temperature annealing effects. Choosing appropriate activation energy of impurity atoms,… (more)

Raghavan, Vinay

2015-01-01T23:59:59.000Z

466

Physics based analytical modelling of silicon carbide (SiC) MESFET considering different ion implantation energy with high temperature annealing.  

E-Print Network [OSTI]

??A Physics based analytical model of ion implanted SiC MESFET has been developed considering the high temperature annealing effects. The diffusion of implanted impurities has… (more)

Yadavalli, Karthik Vishwanath

2015-01-01T23:59:59.000Z

467

Gulyaev–Bleustein Waves in a Layered Structure of Piezoelectric – Periodic Granular High-Temperature Superconductor Structure  

Science Journals Connector (OSTI)

Bragg's interactions of Gulyaev–Bleustein surface waves with a periodic granular high-temperature superconducting medium are studied. Dispersion equations describing the characteristics of surface acoustoelect...

V. A. Krakovskii

2001-06-01T23:59:59.000Z

468

A High -Temperature, High-Voltage, Fast Response Time Linear Regulator in 0.8um BCD-on-SOI.  

E-Print Network [OSTI]

??The sale of hybrid electric vehicles (HEVs) has increased tenfold from the year 2001 to 2009 [1]. With this the demand for high temperature electronics… (more)

Su, Chia Hung

2010-01-01T23:59:59.000Z

469

ReUcs of samarskite structure in a metamict ABU4 mineral and its high-temperature transformations  

E-Print Network [OSTI]

as a proposed high.temperature samarskite phase with wolframite.type stmcture (s.g. P2/c, a~5.63(]) A,b~9

Downs, Robert T.

470

In the OSTI Collections: High-Temperature Superconductors | OSTI, US Dept  

Office of Scientific and Technical Information (OSTI)

High-Temperature Superconductors High-Temperature Superconductors Technology Basic Science Progress towards theory References Research Organizations and Scientific Societies Reports Available through OSTI's SciTech Connect Patents available through OSTI's DOepatents Additional References One of the lessons of quantum physics is that any set of subatomic particles bound together by mutual attractions have quite distinct states of relative motion determined by how the particles interact, and that changing the particles' motion from one such state to another requires that their energy and momentum change by appropriate discrete finite amounts. Electrons bound within a metal to the lattice[Wikipedia] of its positive ions[Wikipedia] are no exception. Under ordinary conditions in our usual environment, an electric field applied to the metal can

471

High Temperature Steam Electrolysis: Demonstration of Improved Long-Term Performance  

SciTech Connect (OSTI)

Long-term performance is an ongoing issue for hydrogen production based on high-temperature steam electrolysis (HTSE). For commercial deployment, solid-oxide electrolysis stacks must achieve high performance with long-term degradation rates of {approx}0.5%/1000 hours or lower. Significant progress has been achieved toward this goal over the past few years. This paper will provide details of progress achieved under the Idaho National Laboratory high temperature electrolysis research program. Recent long-term stack tests have achieved high initial performance with degradation rates less than 5%/khr. These tests utilize internally manifolded stacks with electrode-supported cells. The cell material sets are optimized for the electrolysis mode of operation. Details of the cells and stacks will be provided along with details of the test apparatus, procedures, and results.

J. E. O'Brien; X. Zhang; R. C. O'Brien; G. Tao

2011-11-01T23:59:59.000Z

472

High pressure--high temperature research using high energy synchrotron radiation at the TRISTAN accumulation ring  

SciTech Connect (OSTI)

High energy synchrotron radiation emitted from the bending magnet of the TRISTAN accumulation ring (6.5 GeV) at the National Laboratory for High Energy Physics has been used for the high pressure--high temperature diffraction experiments using a multianvil press system, MAX80. Owing to the specific features of high energy synchroton radiation, significant improvements have been brought to the high pressure research. The wide energy range of diffraction spectrum leads to an increase in the number of observable diffraction peaks in an energy-dispersive method, resulting in an increase in the accuracy of the measurements of the lattice and thermal parameters. Due to the high penetrating power of radiation, diffraction patterns can be taken in a short time from materials containing heavy elements or materials surrounded by a metal foil. Typical examples of high pressure--high temperature experiments with high energy synchrotron radiation are also described.

Kikegawa, T.; Shimomura, O.; Iwasaki, H.; Sato, S.; Mikuni, A.; Iida, A.; Kamiya, N.

1989-07-01T23:59:59.000Z

473

Key technological issues in LMFBR high-temperature structural design - the US perspective  

SciTech Connect (OSTI)

The purpose of this paper is: (1) to review the key technological issues in LMFBR high-temperature structural design, particularly as they relate to cost reduction; and (2) to provide an overview of activities sponsored by the US Department of Energy to resolve the issues and to establish stable, standardized, and defensible structural design methods and criteria. Specific areas of discussion include: weldments, structural validation tests, simplified design analysis procedures, design procedures for piping, validation of the methodology for notch-like geometries, improved life assessment procedures, thermal striping, extension of the methodology to new materials, and ASME high-temperature Code reform needs. The perceived problems and needs in each area are discussed, and the current status of related US activities is given.

Corum, J.M.

1984-01-01T23:59:59.000Z

474

Apparatus and method for removing particulate deposits from high temperature filters  

DOE Patents [OSTI]

A combustion of a fuel-air mixture is used to provide a high-temperature and high-pressure pulse of gaseous combustion products for the back-flush cleaning of ceramic filter elements contained in a barrier filter system and utilized to separate particulates from particulate-laden process gases at high temperature and high pressure. The volume of gaseous combustion products provided by the combustion of the fuel-air mixture is preferably divided into a plurality of streams each passing through a sonic orifice and conveyed to the open end of each filter element as a high pressure pulse which passes through the filter elements and dislodges dust cake supported on a surface of the filter element.

Nakaishi, Curtis V. (Morgantown, WV); Holcombe, Norman T. (McMurray, PA); Micheli, Paul L. (Morgantown, WV)

1992-01-01T23:59:59.000Z

475

Novel Carbon Nanotube-Based Nanostructures for High-Temperature Gas Sensing  

SciTech Connect (OSTI)

The primary objective of this research is to examine the feasibility of using vertically aligned multi-wall carbon nanotubes (MWCNTs) as a high temperature sensor material for fossil energy systems where reducing atmospheres are present. In the initial period of research, we fabricated capacitive sensors for hydrogen sensing using vertically aligned MWCNTs. We found that CNT itself is not sensitive to hydrogen. Moreover, with the help of Pd electrodes, hydrogen sensors based on CNTs are very sensitive and fast responsive. However, the Pd-based sensors can not withstand high temperature (T<200 C). In the last year, we successfully fabricated a hydrogen sensor based on an ultra-thin nanoporous titanium oxide (TiO{sub 2}) film supported by an AAO substrate, which can operate at 500 C with hydrogen concentrations in a range from 50 to 500 ppm.

Zhi Chen; Kozo Saito

2008-08-31T23:59:59.000Z

476

2500-Hour High Temperature Solid-Oxide Electrolyzer Long Duration Test  

SciTech Connect (OSTI)

The Idaho National Laboratory (INL) has been developing the concept of using solid oxide fuel cells as electrolyzers for large-scale, high-temperature (efficient), hydrogen production. This program is sponsored by the U.S. Department of Energy under the Nuclear Hydrogen Initiative. Utilizing a fuel cell as an electrolyzer introduces some inherent differences in cell operating conditions. In particular, the performance of fuel cells operated as electrolyzers degrades with time faster. This issue of electrolyzer cell and stack performance degradation over time has been identified as a major barrier to technology development. Consequently, the INL has been working together with Ceramatec, Inc. (Salt Lake City, Utah) to improve the long-term performance of high temperature electrolyzers. As part of this research partnership, the INL conducted a 2500 hour test of a Ceramatec designed and produced stack operated in the electrolysis mode. This report will provide a summary of experimental results for this long duration test.

C. M. Stoots; J. E. O'Brien; K. G. Condie; L. Moore-McAteer; J. J. Hartvigsen; D. Larsen

2009-11-01T23:59:59.000Z

477

A high pressure, high temperature study of 1,1-diamino-2,2-dinitro ethylene  

SciTech Connect (OSTI)

We report a synchrotron energy-dispersive X-ray diffraction study of the novel high explosive 1,1-diamino-2,2-dinitroethylene at high pressures and high temperatures. Pressure was generated using a Paris-Edinburgh cell to employ larger sample volumes. High temperatures were created using a resistive graphite cylinder surrounding the sample. The PT phase diagram was explored in the 3.3 GPa pressure range and in the {approx} 400 C temperature range. We believe that the sample commenced in the {alpha}-phase and then ended up in an amorphous phase when the temperature increased beyond 280 C near 2 GPa, which we believe to be the {gamma}-phase. Further pressure and temperature cycling suggests that the sample transformed reversibly into and out of the amorphous phase near the phase line.

Pravica, Michael; Galley, Martin; Park, Changyong; Ruiz, Harrison; Wojno, Jennifer (UNLV); (CIW)

2012-08-29T23:59:59.000Z

478

Initial Operation of the High Temperature Electrolysis Integrated Laboratory Scale Experiment at INL  

SciTech Connect (OSTI)

An integrated laboratory scale, 15 kW high-temperature electrolysis facility has been developed at the Idaho National Laboratory under the U.S. Department of Energy Nuclear Hydrogen Initiative. Initial operation of this facility resulted in over 400 hours of operation with an average hydrogen production rate of approximately 0.9 Nm3/hr. The integrated laboratory scale facility is designed to address larger-scale issues such as thermal management (feed-stock heating, high-temperature gas handling), multiple-stack hot-zone design, multiple-stack electrical configurations, and other “integral” issues. This paper documents the initial operation of the ILS, with experimental details about heat-up, initial stack performance, as well as long-term operation and stack degradation.

C. M. Stoots; J. E. O'Brien; K. G. Condie; J. S. Herring; J. J. Hartvigsen

2008-06-01T23:59:59.000Z

479

High Temperature Solid-Oxide Electrolyzer 2500 Hour Test Results At The Idaho National Laboratory  

SciTech Connect (OSTI)

The Idaho National Laboratory (INL) has been developing the concept of using solid oxide fuel cells as electrolyzers for large-scale, high-temperature (efficient), hydrogen production. This program is sponsored by the U.S. Department of Energy under the Nuclear Hydrogen Initiative. Utilizing a fuel cell as an electrolyzer introduces some inherent differences in cell operating conditions. In particular, the performance of fuel cells operated as electrolyzers degrades with time faster. This issue of electrolyzer cell and stack performance degradation over time has been identified as a major barrier to technology development. Consequently, the INL has been working together with Ceramatec, Inc. (Salt Lake City, Utah) to improve the long-term performance of high temperature electrolyzers. As part of this research partnership, the INL conducted a 2500 hour test of a Ceramatec designed and produced stack operated in the electrolysis mode. This paper will provide a summary of experimental results to date for this ongoing test.

Carl Stoots; James O'Brien; Stephen Herring; Keith Condie; Lisa Moore-McAteer; Joseph J. Hartvigsen; Dennis Larsen

2009-11-01T23:59:59.000Z

480

High Temperature Gas-Cooled Reactor Projected Markets and Preliminary Economics  

SciTech Connect (OSTI)

This paper summarizes the potential market for process heat produced by a high temperature gas-cooled reactor (HTGR), the environmental benefits reduced CO2 emissions will have on these markets, and the typical economics of projects using these applications. It gives examples of HTGR technological applications to industrial processes in the typical co-generation supply of process heat and electricity, the conversion of coal to transportation fuels and chemical process feedstock, and the production of ammonia as a feedstock for the production of ammonia derivatives, including fertilizer. It also demonstrates how uncertainties in capital costs and financial factors affect the economics of HTGR technology by analyzing the use of HTGR technology in the application of HTGR and high temperature steam electrolysis processes to produce hydrogen.

Larry Demick

2011-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-temperature nano-derived micro-h2" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

The performance of High-Temperature Reactor fuel particles at extreme temperatures  

SciTech Connect (OSTI)

Coated particles embedded in graphitic elements are the fuel for the High-Temperature Reactor (HTR). Experimental investigations of the performance of particles at extremely high temperatures have been conducted to achieve an understanding of coating failure mechanisms and to establish the data base for safety and risk analyses of hypothetical accidents in large- and medium-sized HTRs. The primary mechanism for coating failure and fission product release in the 1900 to 2500/sup 0/C temperature range is thermal decomposition of silicon carbide (SiC). Heating tests have provided the activation energy of this process and the correlation of SiC decomposition with coating failure and subsequent fission product release.

Nabielek, H.; Schenk, W.; Heit, W.; Mehner, A.W.; Goodin, D.T.

1989-01-01T23:59:59.000Z

482

Using high temperature baghouses to enhance desulfurization following economizer sorbent injection  

SciTech Connect (OSTI)

In order to explore the potential of using high temperature baghouses to enhance SO{sub 2} removal following upstream sorbent injection, an integrated two-stage reactor system has been built. It consists of an injection stage and a filtration stage. Distinct from one-stage fixed-bed reactors, sorbent particles in this system are initially converted under controlled injection conditions before entering the filtration reactor chamber. By the aid of the system, several unique features regarding the gas-solid reactions in the baghouse after economizer zone sorbent injection have been revealed. Results have shown that the appropriate usage of a high temperature baghouse may substantially enhance the performance of the process. The further SO{sub 2} removal in the baghouse is comprehensively affected by both the conditions in the injection zone and those in the baghouse.

Li, G.; Keener, T.C. [Univ. of Cincinnati, OH (United States). Dept. of Civil and Environmental Engineering

1995-12-31T23:59:59.000Z

483

Development of high temperature transport technology for LiCl-KCl eutectic salt in pyroprocessing  

SciTech Connect (OSTI)

The development of high-temperature transport technologies for molten salt is a prerequisite and a key issue in the industrialization of pyro-reprocessing for advanced fuel cycle scenarios. The solution of a molten salt centrifugal pump was discarded because of the high corrosion power of a high temperature molten salt, so the suction pump solution was selected. An apparatus for salt transport experiments by suction was designed and tested using LiC-KCl eutectic salt. The experimental results of lab-scale molten salt transport by suction showed a 99.5% transport rate (ratio of transported salt to total salt) under a vacuum range of 100 mtorr - 10 torr at 500 Celsius degrees. The suction system has been integrated to the PRIDE (pyroprocessing integrated inactive demonstration) facility that is a demonstrator using non-irradiated materials (natural uranium and surrogate materials). The performance of the suction pump for the transport of molten salts has been confirmed.

Lee, Sung Ho; Lee, Hansoo; Kim, In Tae; Kim, Jeong-Guk [Korea Atomic Energy Research Institute, 1045 Daedeok-daaro, Yuseong-gu, Daejeon, 305-353 (Korea, Republic of)

2013-07-01T23:59:59.000Z

484

High Temperature, Large Sample Volume, Constant Flow Magic Angle Spinning NMR Probe for a 11  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

High Temperature, Large Sample Volume, Constant Flow Magic Angle Spinning NMR Probe for a High Temperature, Large Sample Volume, Constant Flow Magic Angle Spinning NMR Probe for a 11.7 T Magnetic Field for In Situ Catalytic Reaction Characterization Project start date: April 1, 2007 EMSL Lead Investigator: Joseph Ford, EMSL High Field Magnetic Resonance Facility Co-investigators: Jian Zhi Hu, Macromolecular Structure and Dynamics, Biological Science Division, FCSD Jesse Sears and David W. Hoyt, EMSL High Field Magnetic Resonance Facility Detailed understanding of the mechanisms involved in a catalytic reaction requires identification of the nature of the active sites and the temporal evolution of reaction intermediates. Although optical methods such as UV-visible and infrared (IR) spectroscopies can be used for some types of reactions, these do not

485

Improved germination of pansy seed at high temperatures by priming with salt solutions  

E-Print Network [OSTI]

; Khan et al. , 1981). The Kinetics of Water Uptake by Seeds Many seeds placed in distilled water in petri dishes under optimum conditions for germination show a triphasic pattern of water uptake (Hadas, 1982). The first stage of water uptake... OF PANSY SEED AT HIGH TEMPERATURES BY PRIMING WITH SALT SOLUTIONS Introduction Seed germination can be divided into three separate but overlapping phases: imbibition, transition or lag, and radicle emergence (Hadas, 1982). An osmotically adjusted...

Yoon, Beyoung-Han

1995-01-01T23:59:59.000Z

486

The decomposition of methyltrichlorosilane: Studies in a high-temperature flow reactor  

SciTech Connect (OSTI)

Experimental measurements of the decomposition of methyltrichlorosilane (MTS), a common silicon carbide precursor, in a high-temperature flow reactor are presented. The results indicate that methane and hydrogen chloride are major products of the decomposition. No chlorinated silane products were observed. Hydrogen carrier gas was found to increase the rate of MTS decomposition. The observations suggest a radical-chain mechanism for the decomposition. The implications for silicon carbide chemical vapor deposition are discussed.

Allendorf, M.D.; Osterheld, T.H.; Melius, C.F.

1994-01-01T23:59:59.000Z

487

Laser-based diagnostics for density, temperature, velocity, and dissociation fraction in high temperature hydrogen flows  

SciTech Connect (OSTI)

This paper is essentially a review of the current state of the art in hydrogen atom and hydrogen molecule diagnostics. This paper contains some of our own results and ideas along with results from many other laboratories. This is not intended to be an exhaustive review; instead it summarizes some techniques which we believe are ideally suited as diagnostics for high temperature hydrogen which are of paramount importance for the Space Exploration Initiative (SEI). 31 refs., 1 fig.

Sappey, A.D.; Funk, D.J.

1991-01-01T23:59:59.000Z

488

INTEGRATION OF HIGH TEMPERATURE GAS REACTORS WITH IN SITU OIL SHALE RETORTING  

SciTech Connect (OSTI)

This paper evaluates the integration of a high-temperature gas-cooled reactor (HTGR) to an in situ oil shale retort operation producing 7950 m3/D (50,000 bbl/day). The large amount of heat required to pyrolyze the oil shale and produce oil would typically be provided by combustion of fossil fuels, but can also be delivered by an HTGR. Two cases were considered: a base case which includes no nuclear integration, and an HTGR-integrated case.

Eric P. Robertson; Michael G. McKellar; Lee O. Nelson

2011-05-01T23:59:59.000Z

489

High-temperature in situ magic-angle spinning NMR studies of chemical reactions on catalysts  

E-Print Network [OSTI]

temperature jump to 623 K. Important differences observed in this study relative to previous investigations at lower temperatures include well-resolved signals for adsorbed versus exogenous (gas phase) methanol and dimethyl ether, and a higher yield... described in the text. 29 Expanded view of the first three spectra in Figure 7 showing the regions containing methanol and dimethyl ether. In the high- temperature spectra two peaks are present for both species; gas phase (48. 0 ppm) and adsorbed (53. 1...

Oliver, F. Gregory

2012-06-07T23:59:59.000Z

490

ECUT energy data reference series: high-temperature materials for advanced heat engines  

SciTech Connect (OSTI)

Information that describes the use of high-temperature materials in advanced heat engines for ground transportation applications is summarized. Applications discussed are: automobiles, light trucks, and medium and heavy trucks. The information provided on each of these modes includes descriptions of the average conversion efficiency of the engine, the capital stock, the amount of energy used, and the activity level as measured in ton-miles.

Abarcar, R.B.; Hane, G.J.; Johnson, D.R.

1984-07-01T23:59:59.000Z

491

Self-Organized Networks and Lattice Effects in High Temperature Superconductors II: Fermi Arc Anomalies  

E-Print Network [OSTI]

The self-organized dopant percolative filamentary model, entirely orbital in character (no fictive spins), explains the evolution with doping of Fermi arcs observed by ARPES, including the previously unexplained abrupt transitions in quasiparticle strength observed near optimal doping in cuprate high temperature superconductors. Similarly abrupt transitions are also observed in time-resolved picosecond relaxation spectroscopy at 1.5 eV, and these are explained as well, using no new assumptions and no adjustable parameters.

J. C. Phillips

2006-11-07T23:59:59.000Z

492

High-frequency vortex dynamics and dissipation of high-temperature superconductors  

Science Journals Connector (OSTI)

The high-frequency vortex dynamics of high-temperature superconductors near the flux-line depinning threshold is investigated based on a thermally activated flux-flow (TAFF) model. Dissipation due to vortex motion driven by a microwave electromagnetic field is studied as a function of the frequency, temperature, dc magnetic field, and microwave power. The generalized TAFF model is also compared to the conventional flux-creep theory and is found qualitatively consistent.

N.-C. Yeh

1991-01-01T23:59:59.000Z

493

Method and apparatus for cooling high temperature superconductors with neon-nitrogen mixtures  

DOE Patents [OSTI]

Apparatus and methods for cooling high temperature superconducting materials (HTSC) to superconductive temperatures within the range of 27.degree. K. to 77.degree. K. using a mixed refrigerant consisting of liquefied neon and nitrogen containing up to about ten mole percent neon by contacting and surrounding the HTSC material with the mixed refrigerant so that free convection or forced flow convection heat transfer can be effected.

Laverman, Royce J. (South Holland, IL); Lai, Ban-Yen (Hinsdale, IL)

1993-01-01T23:59:59.000Z

494

Temperature evolution of the spectral peak in high-temperature superconductors  

Science Journals Connector (OSTI)

Recent photoemission data in the high-temperature cuprate superconductor Bi2212 have been interpreted in terms of a sharp spectral peak with a temperature-independent lifetime, whose weight strongly decreases upon heating. By a detailed analysis of the data, we are able to extract the temperature dependence of the electron self-energy, and demonstrate that this interpretation is misleading. Rather, the spectral peak loses its integrity above Tc due to a large reduction in the electron lifetime.

M. R. Norman; A. Kaminski; J. Mesot; J. C. Campuzano

2001-03-22T23:59:59.000Z

495

Fuel Processing for High-Temperature High-Efficiency Fuel Cells  

Science Journals Connector (OSTI)

With commonly available fuels such as natural gas, only the high-temperature fuel cells MCFC and SOFC have reached electrical efficiencies of ?50% lower heating value (LHV). ... A high electrical efficiency of 60% has recently been demonstrated in a stationary field test system by Ceramic Fuel Cells Ltd. with a 2 kW(electrical) unit fueled by natural gas using DIR as fuel processing option. ... Some catalyst manufacturers supply their catalysts in the reduced and stabilized state at a premium price. ...

Khaliq Ahmed; Karl Föger

2010-07-15T23:59:59.000Z

496

Corrosion behavior of zirconia-coated Hastelloy X in a high-temperature helium environment  

SciTech Connect (OSTI)

The corrosion behavior of Hastelloy X coated with (NiCrAl)/(ZrO/sub 2/-CaC/sub 2/) was examined, after serving as the liner tube of helium engineering demonstration loop (HENDEL) hot gas duct. The Hastelloy X with the ceramic coating system was exposed to high-temperature helium gas for --6000 h. The compositions of oxide films formed on Hastelloy X were entirely different between the noncoated and ceramic-coated tubes.

Kondo, Y.; Fukaya, K.

1989-01-01T23:59:59.000Z

497

Preliminary study on high temperature transport technology for molten salt in pyroprocessing  

Science Journals Connector (OSTI)

Pyroprocessing technology is one of the most promising technologies for an advanced fuel cycle with favorable economic potential and intrinsic proliferation-resistance. In pyroprocessing technology, the development of high-temperature transport technologies for molten salt is a crucial prerequisite and a key issue in the industrialization of pyro-reprocessing. However, there have been a few transport studies on high-temperature molten salt. Three different salt transport technologies (gravity, suction pump, and centrifugal pump) were investigated, a suction pump transport method was selected for molten salt transport owing to its flexibility. An apparatus for suction transport experiments was designed and installed for the development of high temperature molten salt transport technology. About 2 kg of LiCl–KCl eutectic salt was prepared by mixing 99.0%, LiCl and \\{KCl\\} and drying in a convection dry oven at 200 °C for 1 h. Predissolution tests of the prepared LiCl–KCl eutectic salt using the melting reactor of the experimental apparatus was carried out to investigate the dissolution behavior of the prepared LiCl–KCl eutectic salt. From the results of the pre-dissolution test, it was found that prepared LiCl–KCl eutectic salt was well dissolved at 500 °C. High temperature molten salt transport experiments by suction are currently being performed using the prepared LiC–KCl eutectic salt. The preliminary experimental results of lab-scale molten salt transport showed a 99.5% transport rate (ratio of transported salt to total salt) under a vacuum range of 100 m torr–10 torr at 500 °C.

Sung Ho Lee; Hansoo Lee; Jeong-Guk Kim

2013-01-01T23:59:59.000Z

498

Reference modular High Temperature Gas-Cooled Reactor Plant: Concept description report  

SciTech Connect (OSTI)

This report provides a summary description of the Modular High Temperature Gas-Cooled Reactor (MHTGR) concept and interim results of assessments of costs, safety, constructibility, operability, maintainability, and availability. Conceptual design of this concept was initiated in October 1985 and is scheduled for completion in 1987. Participating industrial contractors are Bechtel National, Inc. (BNI), Stone and Webster Engineering Corporation (SWEC), GA Technologies, Inc. (GA), General Electric Co. (GE), and Combustion Engineering, Inc. (C-E).

Not Available

1986-10-01T23:59:59.000Z

499

High Temperature Capabililty and Innovative Cooling with a Spar and Shell Turbine Blade - Florida Turbine Technologies  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Temperature Capability and Temperature Capability and Innovative Cooling with a Spar and Shell Turbine Blade-Florida Turbine Technologies Background Florida Turbine Technologies, Inc. (FTT) is currently developing advanced aerothermal technologies centered on spar and shell airfoil concepts meant to provide highly durable turbine components that require the lowest cooling flow possible. The spar-shell system represents a unique opportunity for the use of advanced, high-temperature materials

500

Diffusion velocity correlation for nuclear graphite gasification at high temperature and low Reynolds numbers  

SciTech Connect (OSTI)

The safety analysis of High-Temperature and Very High Temperature gas-cooled Reactors requires reliable estimates of nuclear graphite gasification as a function of temperature, among other parameters, in the unlikely event of an air ingress accident. Although the rates of the prevailing chemical reactions increase exponentially with temperature, graphite gasification at high temperatures is limited by the oxygen diffusion through the boundary layer. The effective diffusion velocity depends on the total flow rate and pressure of the bulk air-gas mixture. This paper develops a semi-empirical Sherwood number correlation for calculating the oxygen diffusion velocity. The correlation is based on a compiled database of the results of convective heat transfer experiments with wires and cylinders of different diameters in air, water and paraffin oil at 0.006 {<=} Re {<=} 1,604 and 0.068 {<=} Sc {<=} 35.2, and of mass transfer experiments at 4.8 {<=} Re {<=} 77 and 1,300 {<=} Sc {<=} 2,000. The developed correlation is within {+-} 8% of the compiled database of 567 data points and consistent with reported gasification rate measurements at higher temperatures in experiments using different size specimens of nuclear graphite grades of NBG-18 and NB-25, IG-11, IG-110 and IG-430 in atmospheric air at 0.08 {<=} Re {<=} 30. Unlike the Graetz solution that gives a constant Sh of 3.66 at Re {<=} 1.0, the present correlation shows Sh decreases monotonically to much lower values with decreasing Re. (authors)

El-Genk, M. S. [Inst. for Space and Nuclear Power Studies, Univ. of New Mexico, Albuquerque, NM (United States); Chemical and Nuclear Engineering Dept., Univ. of New Mexico, Albuquerque, NM (United States); Mechanical Engineering Dept., Univ. of New Mexico, Albuquerque, NM (United States); Tournier, J. M. P. [Inst. for Space and Nuclear Power Studies, Univ. of New Mexico, Albuquerque, NM (United States); Chemical and Nuclear Engineering Dept., Univ. of New Mexico, Albuquerque, NM (United States)

2012-07-01T23:59:59.000Z