Powered by Deep Web Technologies
Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

high  

Gasoline and Diesel Fuel Update (EIA)

0 0 Summary Our short-term outlook for a wide array of energy prices has been adjusted upward as international and domestic energy supply conditions have tightened. We think that crude oil prices are as likely as not to end the year $2 to $3 per barrel higher than our previous projections. Thus, we think that the probability of West Texas Intermediate costing an average of $30 per barrel or more at midwinter is about 50 percent. On their current track, heating oil prices are likely to be about 30 percent above year-ago levels in the fourth quarter. Prices for Q1 2001 seem more likely now to match or exceed the high level seen in Q1 2000. Tight oil markets this year and an inherent propensity for high gas utilization in incremental power supply have resulted in rising North American natural gas

2

high  

Gasoline and Diesel Fuel Update (EIA)

0 0 Highlights International Oil Markets Prices. We have raised our world oil price projection by about $2 per barrel for this month because of assumed greater compliance by OPEC to targeted cuts, especially for the second quarter of 2000 (Figure 1). The expected decline in world petroleum inventories continues (Figure 2), and, given the generally stiff resolve of OPEC members to maintain production cuts, any sign of a turnaround in stocks may be postponed until later this year than previously assumed (Q3 instead of Q2). Our current estimate for the average import cost this past January is now $25 per barrel, a nearly $15-per-barrel increase from January 1999. Crude oil prices are expected to remain at relatively high levels for the first half of 2000, but

3

Design Procedure for a Very High Speed Slotless Permanent Magnet Motor Pierre-Daniel Pfister, Student Member, IEEE and Yves Perriard, Senior Member, IEEE  

E-Print Network (OSTI)

Design Procedure for a Very High Speed Slotless Permanent Magnet Motor Pierre-Daniel Pfister speed slotless permanent magnet motor design procedure using an analyti- cal model. The multiphysics in the center, a magnet, an air gap, and the stator yoke. In our case, the shaft radius is set to zero

Psaltis, Demetri

4

2009 Spring : Highly Distinguished Honors Highly Distinguished  

E-Print Network (OSTI)

Armstrong Anna P Highly Distinguished Armstrong Jack Ray Highly Distinguished Armstrong Sarah Rose Highly

Kasman, Alex

5

High Tech High Chula Vista  

Chula Vista, CA High Tech High Chula Vista is a public charter school serving 550 students in grades 9 to 12 with an approach rooted in project-based learning. The school fosters student engagement by knowing students well, tapping into student experience and interests, and building a strong sense of community. Through internships and projects based in the community, students collaborate with adults on work with meaning that extends well beyond the school walls.

6

High energy and high excitement  

Science Journals Connector (OSTI)

......definite, stream of energy. Most previous optical...If there is a slower car in front on a highway...result, which are akin to car collisions. These gigantic clouds of high-energy electrons, now seen...outcrops. However, an alternative possibility is that the......

Peter Bond

2001-02-01T23:59:59.000Z

7

High School Teams 2015  

NLE Websites -- All DOE Office Websites (Extended Search)

School Salem, OR McNary High School Keizer, OR Mountain View High School Vancouver, WA North Bend High School North Bend, OR North Medford High School Medford, OR Olympia High...

8

High Temperatures & Electricity Demand  

E-Print Network (OSTI)

High Temperatures & Electricity Demand An Assessment of Supply Adequacy in California Trends.......................................................................................................1 HIGH TEMPERATURES AND ELECTRICITY DEMAND.....................................................................................................................7 SECTION I: HIGH TEMPERATURES AND ELECTRICITY DEMAND ..........................9 BACKGROUND

9

Senior Debt Fastball Presentation  

Energy.gov (U.S. Department of Energy (DOE))

Plenary III: Project Finance and Investment Senior Debt Fastball Presentation Phillip Thomas, Senior Vice President of Commercial Lending, Heartland Bank

10

High Performance Networks for High Impact Science  

NLE Websites -- All DOE Office Websites (Extended Search)

was printed on recycled paper. (800) High-Performance Networks for High-Impact Science Report of the August 13-15, 2002, Workshop Conducted by the Office of Advanced...

11

High-Tech Halloween  

NLE Websites -- All DOE Office Websites (Extended Search)

High-Tech Halloween Catch an Event Events Happening Now Events Calendar High-Tech Halloween Lifelong Learning Mailing List 70th Events Lectures invisible utility element High-Tech...

12

High Energy Nuclear Events  

Science Journals Connector (OSTI)

......research-article Articles High Energy Nuclear Events Enrico Fermi Institute...Distribution of Pions produced in High Energy Nuclear Collisions Yoshihiro Yamamoto...Possible Interpretation of High Energy Nuclear Events Nobuo Yajima, Shuji Takagi......

Enrico Fermi

1950-07-01T23:59:59.000Z

13

High-frequency, high-intensity photoionization  

Science Journals Connector (OSTI)

Two analytical methods for computing ionization by high-frequency fields are compared. Predicted ionization rates compare well, but energy predictions for the onset of ionization...

Reiss, H R

1996-01-01T23:59:59.000Z

14

High School Testing  

E-Print Network (OSTI)

The High School Testing Program has been suspended. Jerry Woodward High School Testing Program Mathematical Sciences Building 150 N. University Street

15

high algae diversity  

Science Journals Connector (OSTI)

high algae diversity ? Vergesellschaftung f mit mehreren Algenarten oder unterschiedlichen Algengattungen

2014-08-01T23:59:59.000Z

16

High Temperature Structural Foam  

Science Journals Connector (OSTI)

The Aerospace Industry is experiencing growing demand for high performance polymer foam. The X-33 program needs structural foam insulation capable of retaining its strength over a wide range of environmental conditions. The High Speed Research Program ...

Weiser Erik S.; Baillif Faye F.; Grimsley Brian W.; Marchello Joseph M.

1998-05-01T23:59:59.000Z

17

A Natural Gas, High Compression Ratio, High Efficiency ICRE ...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

A Natural Gas, High Compression Ratio, High Efficiency ICRE A Natural Gas, High Compression Ratio, High Efficiency ICRE Using natural gas and gasoline modeling, indications are...

18

Large-dimension, high-ZT Thermoelectric Nanocomposites for High...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Large-dimension, high-ZT Thermoelectric Nanocomposites for High-Power High-efficiency Waste Heat Recovery for Electricity Generation Large-dimension, high-ZT Thermoelectric...

19

Energy Storage Testing and Analysis High Power and High Energy...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Testing and Analysis High Power and High Energy Development Energy Storage Testing and Analysis High Power and High Energy Development 2009 DOE Hydrogen Program and Vehicle...

20

High Energy Physics  

NLE Websites -- All DOE Office Websites (Extended Search)

Basic Energy Science Biological and Environmental Research Fusion Energy Sciences High Energy Physics Nuclear Physics Advanced Scientific Computing Research Pioneering...

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

High Performance Computing in  

E-Print Network (OSTI)

High Performance Computing in Bioinformatics Thomas Ludwig (t.ludwig@computer.org) Ruprecht PART I: High Performance Computing Thomas Ludwig PART II: HPC Computing in Bioinformatics Alexandros #12;© Thomas Ludwig, Alexandros Stamatakis, GCB'04 3 PART I High Performance Computing Introduction

Stamatakis, Alexandros

22

High Performance Computing  

NLE Websites -- All DOE Office Websites (Extended Search)

Information Science, Computing, Applied Math » Information Science, Computing, Applied Math » High Performance Computing High Performance Computing Providing world-class high performance computing capability that enables unsurpassed solutions to complex problems of strategic national interest Gary Grider High Performance Computing Division Leader Randal Rheinheimer High Performance Computing Deputy Division Leader Contact Us Carol Hogsett Student/Internship Opportunities Email Division Office Email Managing world-class supercomputing centers Powerall simulations modeling Read caption + The Powerwall is used by LANL scientists to view objects and processes in 3D. High Performance Computing video 13:01 Gary Grider, HPC Divison Leader The High Performance Computing (HPC) Division supports the Laboratory mission by managing world-class Supercomputing Centers.

23

Brookhaven High Energy Physics  

NLE Websites -- All DOE Office Websites (Extended Search)

High-Energy Physics High-Energy Physics High-energy physicists probe the properties and behavior of the most elementary particles in the universe. At the Alternating Gradient Synchrotron (AGS), they perform experiments of unique sensitivity using high-intensity, intermediate-energy beams. The AGS currently provides the world's most intense high-energy proton beam. It is also the world's most versatile accelerator, accelerating protons, polarized protons, and heavy ions to near the speed of light. Magnet system at Brookhaven used to measure the magnetic moment of the muon. Important discoveries in high-energy physics were made at the AGS within the last decade. An international collaboration, including key physicists from Brookhaven, performed a very high-precision measurement of a property

24

High resolution, high speed ultrahigh vacuum microscopy  

SciTech Connect

The history and future of transmission electron microscopy (TEM) is discussed as it refers to the eventual development of instruments and techniques applicable to the real time in situ investigation of surface processes with high resolution. To reach this objective, it was necessary to transform conventional high resolution instruments so that an ultrahigh vacuum (UHV) environment at the sample site was created, that access to the sample by various in situ sample modification procedures was provided, and that in situ sample exchanges with other integrated surface analytical systems became possible. Furthermore, high resolution image acquisition systems had to be developed to take advantage of the high speed imaging capabilities of projection imaging microscopes. These changes to conventional electron microscopy and its uses were slowly realized in a few international laboratories over a period of almost 40 years by a relatively small number of researchers crucially interested in advancing the state of the art of electron microscopy and its applications to diverse areas of interest; often concentrating on the nucleation, growth, and properties of thin films on well defined material surfaces. A part of this review is dedicated to the recognition of the major contributions to surface and thin film science by these pioneers. Finally, some of the important current developments in aberration corrected electron optics and eventual adaptations to in situ UHV microscopy are discussed. As a result of all the path breaking developments that have led to today's highly sophisticated UHV-TEM systems, integrated fundamental studies are now possible that combine many traditional surface science approaches. Combined investigations to date have involved in situ and ex situ surface microscopies such as scanning tunneling microscopy/atomic force microscopy, scanning Auger microscopy, and photoemission electron microscopy, and area-integrating techniques such as x-ray photoelectron spectroscopy, ultraviolet photoelectron spectroscopy, Auger electron spectroscopy, low-energy electron diffraction, temperature programmed desorption, high-resolution electron energy-loss and Fourier-transform infrared spectroscopies, and others. Material systems ranging from atomic layers of metals and semiconductors to biology related depositions are being investigated. In the case of biological materials, however, strict limitations to high-resolution applications are imposed by electron radiation damage considerations.

Poppa, Helmut [National Center for Electron Microscopy, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States)

2004-09-01T23:59:59.000Z

25

High Precision Measurements Using High Frequency Signals  

E-Print Network (OSTI)

Generalized lock-in amplifiers use digital cavities with Q-factors as high as 5X10^8. In this letter, we show that generalized lock-in amplifiers can be used to analyze microwave (giga-hertz) signals with a precision of few tens of hertz. We propose that the physical changes in the medium of propagation can be measured precisely by the ultra-high precision measurement of the signal. We provide evidence to our proposition by verifying the Newton's law of cooling by measuring the effect of change in temperature on the phase and amplitude of the signals propagating through two calibrated cables. The technique could be used to precisely measure different physical properties of the propagation medium, for example length, resistance, etc. Real time implementation of the technique can open up new methodologies of in-situ virtual metrology in material design.

Jin, Aohan; Sakurai, Atsunori; Liu, Liang; Edman, Fredrik; wall, Viktor; Pullerits, Tonu; Karki, Khadga J

2014-01-01T23:59:59.000Z

26

High Performance New Construction  

E-Print Network (OSTI)

Funding for Efficient New Buildings through Integrated Project Delivery and High Performance Design-Build Case Study Rolling Plains New Medical Office Building Michael Flores McKinstry mflores@mckinstry.com 469-789-9920 1 ESL-KT-13-12-40 CATEE..., San Antonio, Texas Dec. 16-18 Objectives Explain how High Performance Design Build / Integrated Project Delivery (HPDB/IPD) differs from alternative project delivery methods (and why it is usually better!) Identify the key participants in High...

Flores, M.

2013-01-01T23:59:59.000Z

27

High-Tc Superconductor  

NLE Websites -- All DOE Office Websites (Extended Search)

and Stanford Synchrotron Radiation Laboratory, Stanford University, Stanford, CA 94305 High-temperature superconductors (HTSC's), following their remarkable discovery in 1986,...

28

High Energy Physics  

NLE Websites -- All DOE Office Websites (Extended Search)

Large Scale Production Computing and Storage Requirements for High Energy Physics: Target 2017 HEPlogo.jpg The NERSC Program Requirements Review "Large Scale Computing and Storage...

29

.NET High Performance Computing.  

E-Print Network (OSTI)

?? Graphics Processing Units (GPUs) have been extensively applied in the High Performance Computing (HPC) community. HPC applications require additional special programming environments to improve (more)

Ou, Hsuan-Hsiu

2012-01-01T23:59:59.000Z

30

High coking value pitch  

SciTech Connect

A high coking value pitch prepared from coal tar distillate and has a low softening point and a high carbon value while containing substantially no quinoline insolubles is disclosed. The pitch can be used as an impregnant or binder for producing carbon and graphite articles.

Miller, Douglas J.; Chang, Ching-Feng; Lewis, Irwin C.; Lewis, Richard T.

2014-06-10T23:59:59.000Z

31

High-pressure crystallography  

Science Journals Connector (OSTI)

The history and development of high-pressure crystallography are briefly described and examples of structural transformations in compressed compounds are given. The review is focused on the diamond-anvil cell, celebrating its 50th anniversary this year, the principles of its operation and the impact it has had on high-pressure X-ray diffraction.

Katrusiak, A.

2007-12-21T23:59:59.000Z

32

High Reliability, High TemperatureThermoelectric Power Generation...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Reliability, High TemperatureThermoelectric Power Generation Materials and Technologies High Reliability, High TemperatureThermoelectric Power Generation Materials and Technologies...

33

Sandia National Laboratories: High-Pressure and High-Temperature...  

NLE Websites -- All DOE Office Websites (Extended Search)

ClimateECClimateCarbon CaptureHigh-Pressure and High-Temperature Neutron Reflectometry Cell for Solid-Fluid Interface Studies High-Pressure and High-Temperature Neutron...

34

Creating high performance enterprises  

E-Print Network (OSTI)

How do enterprises successfully conceive, design, deliver, and operate large-scale, engineered systems? These large-scale projects often involve high complexity, significant technical challenges, a large number of diverse ...

Stanke, Alexis K. (Alexis Kristen), 1977-

2006-01-01T23:59:59.000Z

35

High pressure oxygen furnace  

DOE Patents (OSTI)

A high temperature high pressure oxygen furnace having a hybrid partially externally heated construction is disclosed. A metallic bar fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized, the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 inch bar stock and has a length of about 17 inches. This bar stock is gun drilled for over 16 inches of its length with 0.400 inch aperture to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the bar is provided with a small support aperture into which both a support and a thermocouple can be inserted. The closed end of the gun drilled bar is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior. 5 figs.

Morris, D.E.

1992-07-14T23:59:59.000Z

36

High pressure oxygen furnace  

DOE Patents (OSTI)

A high temperature high pressure oxygen furnace having a hybrid partially externally heated construction is disclosed. A metallic bar fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 inch bar stock and has a length of about 17 inches. This bar stock is gun drilled for over 16 inches of its length with 0.400 inch aperture to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the bar is provided with a small support aperture into which both a support and a thermocouple can be inserted. The closed end of the gun drilled bar is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior.

Morris, Donald E. (Kensington, CA)

1992-01-01T23:59:59.000Z

37

High Energy Solar Particles  

Science Journals Connector (OSTI)

6 May 1976 research-article High Energy Solar Particles J. J. Quenby Protons, heavy nuclei and electrons are seen to be emitted from solar flares with energies extending up to the relativistic region. Three different...

1976-01-01T23:59:59.000Z

38

High-Current Accelerators  

E-Print Network (OSTI)

F i g . 13 F i g . 14 A 48 ACCELERATOR F i g . 25 F i g . 16supply. Extrapolation of accelerator energy and current9 . A-48 high-current accelerator, low-velocity end. Fig.

Lawrence, Ernest O.

1955-01-01T23:59:59.000Z

39

High pressure counterflow CHF.  

E-Print Network (OSTI)

This is a report of the experimental results of a program in countercurrent flow critical heat flux. These experiments were performed with Freon 113 at 200 psia in order to model a high pressure water system. An internally ...

Walkush, Joseph Patrick

1975-01-01T23:59:59.000Z

40

High-voltage engineering  

E-Print Network (OSTI)

High-voltage engineering covers the application, the useful use and proper working of high voltages and high fields. Here we give some introductory examples, i.e., septa and kicker at the Large Hadron Collider (14 TeV), the Super Proton Synchrotron (450 GeV) and the Proton Synchrotron (26 GeV) accelerators as found at the European Orginization for Nuclear Research (CERN) today. We briefly cover the theoretical foundation (Maxwell equations) and aspects of numerical field simulation methods. Concepts relating to electrical fields, insulation geometry and medium and breakdown are introduced. We discuss ways of generating high voltages with examples of AC sources (50/60 Hz), DC sources, and pulse sources. Insulation and breakdown in gases, liquids, solids and vacuum are presented, including Paschens law (breakdown field and streamer breakdown). Applications of the above are discussed, in particular the general application of a transformer. We briefly discuss measurement techniques of partial disch...

Gaxiola, E

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

High Performance Window Attachments  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

High Performance Window High Performance Window Attachments D. Charlie Curcija Lawrence Berkeley National Laboratory dccurcija@lbl.gov 510-495-2602 April 4, 2013 2 | Building Technologies Office eere.energy.gov Purpose & Objectives Impact of Project: * Motivate manufacturers to make improvements in Window systems U-Factors, SHGC and daylighting utilization * Increase awareness of benefits from energy efficient window attachments Problem Statement: * A wide range of residential window attachments are available, but they have widely unknown

42

High temperature pressure gauge  

DOE Patents (OSTI)

A high temperature pressure gauge comprising a pressure gauge positioned in fluid communication with one end of a conduit which has a diaphragm mounted in its other end. The conduit is filled with a low melting metal alloy above the diaphragm for a portion of its length with a high temperature fluid being positioned in the remaining length of the conduit and in the pressure gauge.

Echtler, J. Paul (Pittsburgh, PA); Scandrol, Roy O. (Library, PA)

1981-01-01T23:59:59.000Z

43

High efficiency incandescent lighting  

DOE Patents (OSTI)

Incandescent lighting structure. The structure includes a thermal emitter that can, but does not have to, include a first photonic crystal on its surface to tailor thermal emission coupled to, in a high-view-factor geometry, a second photonic filter selected to reflect infrared radiation back to the emitter while passing visible light. This structure is highly efficient as compared to standard incandescent light bulbs.

Bermel, Peter; Ilic, Ognjen; Chan, Walker R.; Musabeyoglu, Ahmet; Cukierman, Aviv Ruben; Harradon, Michael Robert; Celanovic, Ivan; Soljacic, Marin

2014-09-02T23:59:59.000Z

44

High Efficiency, High Performance Clothes Dryer  

SciTech Connect

This program covered the development of two separate products; an electric heat pump clothes dryer and a modulating gas dryer. These development efforts were independent of one another and are presented in this report in two separate volumes. Volume 1 details the Heat Pump Dryer Development while Volume 2 details the Modulating Gas Dryer Development. In both product development efforts, the intent was to develop high efficiency, high performance designs that would be attractive to US consumers. Working with Whirlpool Corporation as our commercial partner, TIAX applied this approach of satisfying consumer needs throughout the Product Development Process for both dryer designs. Heat pump clothes dryers have been in existence for years, especially in Europe, but have not been able to penetrate the market. This has been especially true in the US market where no volume production heat pump dryers are available. The issue has typically been around two key areas: cost and performance. Cost is a given in that a heat pump clothes dryer has numerous additional components associated with it. While heat pump dryers have been able to achieve significant energy savings compared to standard electric resistance dryers (over 50% in some cases), designs to date have been hampered by excessively long dry times, a major market driver in the US. The development work done on the heat pump dryer over the course of this program led to a demonstration dryer that delivered the following performance characteristics: (1) 40-50% energy savings on large loads with 35 F lower fabric temperatures and similar dry times; (2) 10-30 F reduction in fabric temperature for delicate loads with up to 50% energy savings and 30-40% time savings; (3) Improved fabric temperature uniformity; and (4) Robust performance across a range of vent restrictions. For the gas dryer development, the concept developed was one of modulating the gas flow to the dryer throughout the dry cycle. Through heat modulation in a gas dryer, significant time and energy savings, combined with dramatically reduced fabric temperatures, was achieved in a cost-effective manner. The key design factor lay in developing a system that matches the heat input to the dryer with the fabrics ability to absorb it. The development work done on the modulating gas dryer over the course of this program led to a demonstration dryer that delivered the following performance characteristics: (1) Up to 25% reduction in energy consumption for small and medium loads; (2) Up to 35% time savings for large loads with 10-15% energy reduction and no adverse effect on cloth temperatures; (3) Reduced fabric temperatures, dry times and 18% energy reduction for delicate loads; and, (4) Robust performance across a range of vent restrictions.

Peter Pescatore; Phil Carbone

2005-03-31T23:59:59.000Z

45

High Beta Tokamaks  

SciTech Connect

Perhaps the ideal tokamak would have high {beta} ({beta} {approx}> 1) and classical confinement. Such a tokamak has not been found, and we do not know if one does exist. We have searched for such a possibility, so far without success. In 1990, we obtained analytic equilibrium solutions for large aspect ratio tokamaks at {beta} {approx} {Omicron}(1) [1]. These solutions and the extension at high {beta} poloidal to finite aspect ratio [2] provided a basis for the study of high {beta} tokamaks. We have shown that these configurations can be stable to short scale MHD modes [3], and that they have reduced neoclassical transport [4]. Microinstabilities (such as the {del}T{sub i} mode) seem to be stabilized at high {beta} [5] - this is due to the large local shear [3] and the magnetic well. We have some concerns about modes associated with the compressional branch which may appear at high {beta}. Bill Dorland and Mike Kotschenreuther have studied this issue and our concerns may be unfounded. It is certainly tantalizing, especially given the lowered neoclassical transport values, that these configurations could have no microinstabilities and, one could assume, no anomalous transport. Unfortunately, while this work is encouraging, the key question for high {beta} tokamaks is the stability to large scale kink modes. The MHD {beta} limit (Troyon limit) for kink modes at large aspect ratio is problematically low. There is ample evidence from computations that the limit exists. However, it is not known if stable equilibria exist at much higher {beta}--none have been found. We have explored this question in the asymptotic high {beta} poloidal limit. Unfortunately, we are unable to find stable equilibrium and also unable to show that they don't exist. The results of these calculations will be published when a more definitive answer is found.

Cowley, S.

1998-11-14T23:59:59.000Z

46

Thermoelectrics Partnership: High Performance Thermoelectric...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

High Performance Thermoelectric Waste Heat Recovery System Based on Zintl Phase Materials with Embedded Nanoparticles Thermoelectrics Partnership: High Performance Thermoelectric...

47

High Performance Windows Volume Purchase: About the High Performance  

NLE Websites -- All DOE Office Websites (Extended Search)

High Performance Windows Volume Purchase: About the High Performance Windows Volume Purchase: About the High Performance Windows Volume Purchase Program to someone by E-mail Share High Performance Windows Volume Purchase: About the High Performance Windows Volume Purchase Program on Facebook Tweet about High Performance Windows Volume Purchase: About the High Performance Windows Volume Purchase Program on Twitter Bookmark High Performance Windows Volume Purchase: About the High Performance Windows Volume Purchase Program on Google Bookmark High Performance Windows Volume Purchase: About the High Performance Windows Volume Purchase Program on Delicious Rank High Performance Windows Volume Purchase: About the High Performance Windows Volume Purchase Program on Digg Find More places to share High Performance Windows Volume Purchase:

48

Alternative Fuels Data Center: High Occupancy Vehicle (HOV) and High  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

High Occupancy Vehicle High Occupancy Vehicle (HOV) and High Occupancy Toll (HOT) Lane Exemption to someone by E-mail Share Alternative Fuels Data Center: High Occupancy Vehicle (HOV) and High Occupancy Toll (HOT) Lane Exemption on Facebook Tweet about Alternative Fuels Data Center: High Occupancy Vehicle (HOV) and High Occupancy Toll (HOT) Lane Exemption on Twitter Bookmark Alternative Fuels Data Center: High Occupancy Vehicle (HOV) and High Occupancy Toll (HOT) Lane Exemption on Google Bookmark Alternative Fuels Data Center: High Occupancy Vehicle (HOV) and High Occupancy Toll (HOT) Lane Exemption on Delicious Rank Alternative Fuels Data Center: High Occupancy Vehicle (HOV) and High Occupancy Toll (HOT) Lane Exemption on Digg Find More places to share Alternative Fuels Data Center: High

49

High Risk Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Risk Plan Risk Plan John Bashista Melissa Rider Jeff Davis Timeline to date * OMB memo on Improving Government Acquisition issued July 29, 2009 - Review existing contracts and acquisition practices to save 7% of baseline contract spending (3.5% in FY 2010 and 3.5% in FY 2011) - Reduce high risk contracts by 10% the share of dollars obligated in FY2010 - Final plan was due and submitted on November 2, 2009 - OMB reviewed and requested revision Dec 23, 2009 - Revision submitted April 21, 2010 M&Os are an Issue * With respect to reductions in high risk contracting strategies, the M&O contracts was also a challenge since the opportunity to further influence competition and contract type was highly constrained. The Department had already competed approximately 85 percent of its M&O

50

HIGHLY AUTOMATED MACROMOLECULAR  

NLE Websites -- All DOE Office Websites (Extended Search)

AUTOMATED MACROMOLECULAR AUTOMATED MACROMOLECULAR CRYSTALLOGRAPHY BEAMLINE (AMX) Group Leader: Dieter Schneider Proposal Team: M. Allaire 1 , L. Berman 1 , M. Chance 2 , W. Hendrickson 3 , A. Héroux 1 , J. Jakoncic 1 , A. Orville 1 , H. Robinson 1 , D. Schneider 1 , W. Shi 2 , A. Soares 1 , V. Stojanoff 1 , R. Sweet 1 1 Brookhaven National Laboratory, 2 Case Western Reserve University, 3 Columbia University MISSION APPLICATIONS AND CAPABILITIES ADDITIONAL INFORMATION * AMX at NSLS-II will provide structural biologists with ready access to an advanced macromolecular crystallography (MX) beamline for the elucidation of structure and function of macromolecular complexes. * Its high flux, tunable energy, and natively small focal spot will make it a crystallographer's preferred beamline. * Its high degree of automation will provide a high throughput

51

High resolution data acquisition  

DOE Patents (OSTI)

A high resolution event interval timing system measures short time intervals such as occur in high energy physics or laser ranging. Timing is provided from a clock (38) pulse train (37) and analog circuitry (44) for generating a triangular wave (46) synchronously with the pulse train (37). The triangular wave (46) has an amplitude and slope functionally related to the time elapsed during each clock pulse in the train. A converter (18, 32) forms a first digital value of the amplitude and slope of the triangle wave at the start of the event interval and a second digital value of the amplitude and slope of the triangle wave at the end of the event interval. A counter (26) counts the clock pulse train (37) during the interval to form a gross event interval time. A computer (52) then combines the gross event interval time and the first and second digital values to output a high resolution value for the event interval.

Thornton, Glenn W. (Los Alamos, NM); Fuller, Kenneth R. (Los Alamos, NM)

1993-01-01T23:59:59.000Z

52

High resolution data acquisition  

DOE Patents (OSTI)

A high resolution event interval timing system measures short time intervals such as occur in high energy physics or laser ranging. Timing is provided from a clock, pulse train, and analog circuitry for generating a triangular wave synchronously with the pulse train (as seen in diagram on patent). The triangular wave has an amplitude and slope functionally related to the time elapsed during each clock pulse in the train. A converter forms a first digital value of the amplitude and slope of the triangle wave at the start of the event interval and a second digital value of the amplitude and slope of the triangle wave at the end of the event interval. A counter counts the clock pulse train during the interval to form a gross event interval time. A computer then combines the gross event interval time and the first and second digital values to output a high resolution value for the event interval.

Thornton, G.W.; Fuller, K.R.

1993-04-06T23:59:59.000Z

53

High level nuclear waste  

SciTech Connect

The DOE Division of Waste Products through a lead office at Savannah River is developing a program to immobilize all US high-level nuclear waste for terminal disposal. DOE high-level wastes include those at the Hanford Plant, the Idaho Chemical Processing Plant, and the Savannah River Plant. Commercial high-level wastes, for which DOE is also developing immobilization technology, include those at the Nuclear Fuel Services Plant and any future commercial fuels reprocessing plants. The first immobilization plant is to be the Defense Waste Processing Facility at Savannah River, scheduled for 1983 project submission to Congress and 1989 operation. Waste forms are still being selected for this plant. Borosilicate glass is currently the reference form, but alternate candidates include concretes, calcines, other glasses, ceramics, and matrix forms.

Crandall, J L

1980-01-01T23:59:59.000Z

54

High Energy Neutrino Telescopes  

E-Print Network (OSTI)

This paper presents a review of the history, motivation and current status of high energy neutrino telescopes. Many years after these detectors were first conceived, the operation of kilometer-cubed scale detectors is finally on the horizon at both the South Pole and in the Mediterranean Sea. These new detectors will perhaps provide us the first view of high energy astrophysical objects with a new messenger particle and provide us with our first real glimpse of the distant universe at energies above those accessible by gamma-ray instruments. Some of the topics that can be addressed by these new instruments include the origin of cosmic rays, the nature of dark matter, and the mechanisms at work in high energy astrophysical objects such as gamma-ray bursts, active galactic nuclei, pulsar wind nebula and supernova remnants.

Hoffman, K D

2008-01-01T23:59:59.000Z

55

High Energy Neutrino Telescopes  

E-Print Network (OSTI)

This paper presents a review of the history, motivation and current status of high energy neutrino telescopes. Many years after these detectors were first conceived, the operation of kilometer-cubed scale detectors is finally on the horizon at both the South Pole and in the Mediterranean Sea. These new detectors will perhaps provide us the first view of high energy astrophysical objects with a new messenger particle and provide us with our first real glimpse of the distant universe at energies above those accessible by gamma-ray instruments. Some of the topics that can be addressed by these new instruments include the origin of cosmic rays, the nature of dark matter, and the mechanisms at work in high energy astrophysical objects such as gamma-ray bursts, active galactic nuclei, pulsar wind nebula and supernova remnants.

K. D. Hoffman

2008-12-18T23:59:59.000Z

56

High Temperature Superconductors  

Science Journals Connector (OSTI)

Abstract A brief review of the phenomenology of superconductivity, the distinction between type I and type II superconductors, and the application of type II superconductors is followed by a history of the theory of conventional superconductivity. Unconventional high-temperature superconductivity in the copper oxides is reviewed as a phenomenon occurring in narrow two-dimensional bands where the time for an electron transfer between like atoms is comparable to the period of an optical-mode lattice vibration. A family of iron pnictides containing layers of iron atoms may not require an alternative explanation of its high-temperature superconductivity.

J.B. Goodenough

2013-01-01T23:59:59.000Z

57

High strength alloys  

DOE Patents (OSTI)

High strength metal alloys are described herein. At least one composition of a metal alloy includes chromium, nickel, copper, manganese, silicon, niobium, tungsten and iron. System, methods, and heaters that include the high strength metal alloys are described herein. At least one heater system may include a canister at least partially made from material containing at least one of the metal alloys. At least one system for heating a subterranean formation may include a tubular that is at least partially made from a material containing at least one of the metal alloys.

Maziasz, Phillip James [Oak Ridge, TN; Shingledecker, John Paul [Knoxville, TN; Santella, Michael Leonard [Knoxville, TN; Schneibel, Joachim Hugo [Knoxville, TN; Sikka, Vinod Kumar [Oak Ridge, TN; Vinegar, Harold J [Bellaire, TX; John, Randy Carl [Houston, TX; Kim, Dong Sub [Sugar Land, TX

2010-08-31T23:59:59.000Z

58

Highly Parallel Computation  

Science Journals Connector (OSTI)

...ofthe problem size. If the cost is low, the algorithm designer...grains because synchroni-zation costs would be too high with fine...computers known. They limit the cost ofsynchroni-zation and afford...Agency (DARPA) in 1984 (24). Benchmark studies on a prototype data...

Peter J. Denning; Walter F. Tichy

1990-11-30T23:59:59.000Z

59

High Power Cryogenic Targets  

SciTech Connect

The development of high power cryogenic targets for use in parity violating electron scattering has been a crucial ingredient in the success of those experiments. As we chase the precision frontier, the demands and requirements for these targets have grown accordingly. We discuss the state of the art, and describe recent developments and strategies in the design of the next generation of these targets.

Gregory Smith

2011-08-01T23:59:59.000Z

60

Chemistry at High Temperatures  

Science Journals Connector (OSTI)

...347 the condensed phase. Both cases are...show the opposite behavior. These predictions...vapors. Condensed phase B203 B + B203 02...complex silicates and hydrates in high-temperature...characterized by phase diagrams (derived...doubt that thou-sands of new chemical materials...

John L. Margrave

1962-02-02T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Highly oxidized superconductors  

DOE Patents (OSTI)

Novel superconducting materials in the form of compounds, structures or phases are formed by performing otherwise known synthesis in a highly oxidizing atmosphere rather than that created by molecular oxygen at atmospheric pressure or below. This leads to the successful synthesis of novel superconducting compounds which are thermodynamically stable at the conditions under which they are formed. 16 figs.

Morris, D.E.

1994-09-20T23:59:59.000Z

62

High sensitivity accelerometers are  

E-Print Network (OSTI)

Integrated passive components Nanotube based solar cells High frequency ultrasound for nondestruc- tive investigation of organs and cells State-of-the-Art Equipment Keck SMIL is: A rapid prototyping center providing Lab has been key to the development of our product, which is based on Keck SMIL's PZT Solgel films

Lee, Dongwon

63

High Tc Superconductivity  

NLE Websites -- All DOE Office Websites (Extended Search)

by C. Kim (SSRL), D. H. Lu (Stanford), K. M. Shen (Stanford) and Z.-X. Shen (Stanford/SSRL) by C. Kim (SSRL), D. H. Lu (Stanford), K. M. Shen (Stanford) and Z.-X. Shen (Stanford/SSRL) Extensive research efforts to study the novel electronic properties of high-Tc superconductors and their related materials by angle-resolved photoemission spectroscopy at a recently commissioned Beam Line 5-4 (led by Z.-X. Shen) continue to be successful, producing many important results. These results, which are highlighted by five articles recently published in Physical Review Letters and one in Science, brought our understanding steps closer to solving the mystery of the high-Tc superconductivity. With the development of the latest generation of ultra-high resolution electron spectrometers in the past few years, the technique of angle resolved photoemission spectroscopy (ARPES) has recently experienced a renaissance. Nowhere is this revolution more evident than in the study of the high-temperature superconductors, which more than a decade after their discovery, continue to defy theoretical explanation. Recent ARPES experiments performed at Beam Line 5-4 have led to critical new discoveries about the fundamental nature of these mysterious superconductors and are now changing the way that the physics community views these materials. An excellent benchmark for the huge leap in detector resolution and technology is the recent work on Sr2RuO4. Although it belongs to a slightly different family than the high- temperature superconductors, its exotic superconducting mechanism (Tc = 1K) and complex electronic structure make it itself a fascinating material. In the past, due to poor resolutions, ARPES studies on this material were in disagreement with theory and other experimental techniques.

64

Highly Insulating Windows - Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

Cost Cost The following is an estimate of the cost effective incremental cost of highly-insulating windows (U-factor=0.20 Btu/hr-ft2-F) compared to regular ENERGY STAR windows (U-factor 0.35 Btu/hr-ft2-F). Energy savings from lower U-factors were simulated with RESFEN over an assumed useful window life of 25 years. To determine the maximum incremental cost at which highly-insulating windows would still be cost-effective, we used a formula used by many utility companies to calculate the cost of saved energy from energy efficiency programs, based on the programs' cost and savings. We turned this formula around so that the cost of saved energy equals the present energy prices in the studied locations, whereas the program cost (the incremental cost of the windows) is the dependent variable. By entering 5%

65

High frequency reference electrode  

DOE Patents (OSTI)

A high frequency reference electrode for electrochemical experiments comprises a mercury-calomel or silver-silver chloride reference electrode with a layer of platinum around it and a layer of a chemically and electrically resistant material such as TEFLON around the platinum covering all but a small ring or halo' at the tip of the reference electrode, adjacent to the active portion of the reference electrode. The voltage output of the platinum layer, which serves as a redox electrode, and that of the reference electrode are coupled by a capacitor or a set of capacitors and the coupled output transmitted to a standard laboratory potentiostat. The platinum may be applied by thermal decomposition to the surface of the reference electrode. The electrode provides superior high-frequency response over conventional electrodes. 4 figs.

Kronberg, J.W.

1994-05-31T23:59:59.000Z

66

High temperature probe  

DOE Patents (OSTI)

A high temperature probe for sampling, for example, smokestack fumes, and is able to withstand temperatures of 3000.degree. F. The probe is constructed so as to prevent leakage via the seal by placing the seal inside the water jacket whereby the seal is not exposed to high temperature, which destroys the seal. The sample inlet of the probe is also provided with cooling fins about the area of the seal to provide additional cooling to prevent the seal from being destroyed. Also, a heated jacket is provided for maintaining the temperature of the gas being tested as it passes through the probe. The probe includes pressure sensing means for determining the flow velocity of an efficient being sampled. In addition, thermocouples are located in various places on the probe to monitor the temperature of the gas passing there through.

Swan, Raymond A. (Fremont, CA)

1994-01-01T23:59:59.000Z

67

Galaxies at High Redshifts  

E-Print Network (OSTI)

Several conclusions have been reached over the last few years concerning high-redshift galaxies: (1) The excess of faint blue galaxies is due to dwarf galaxies. (2) Star formation peaks at redshifts z ~1-2. (3) It appears to occur piecemeal in any given galaxy and there is no evidence for starbursting throughout a large ~10 kpc galaxy. (4) There is significant and sharp diminution in the number of L* spiral galaxies at redshifts 1high-redshift galaxies in universes with larger volumes per unit redshift, i.e., open or lambda models, which have lower deceleration parameters.

A. Yahil; K. M. Lanzetta; A. Fernandez-Soto

1998-03-05T23:59:59.000Z

68

Highly Insulating Window Technology  

NLE Websites -- All DOE Office Websites (Extended Search)

Window Technology Window Technology Temperature differentials across a window, particularly with cold exterior environments in residential buildings, can lead to significant energy losses. Currently available low-emissivity coatings, gas-fills, and insulating frames provide significant energy savings over typical single or double glazed products. The EWC website provides information on how double glazed low-e gas-filled windows work as well as information on commercially available superwindows (three layer, multiple low-e coatings, high performance gas-fills). The next generation of highly insulating window systems will benefit from incremental improvements being made to current components (i.e. more insulating spacers and frame materials/designs, low-e coatings with improved performance properties). LBNL uses its experimental facilities and software tools to collaborate with window and glass industry representatives to better understand the impacts of new components on overall product performance.

69

National High Magnetic Field Laboratory - High B/T Program  

NLE Websites -- All DOE Office Websites (Extended Search)

of experiments where needed. Instrumentation is available for studies of: Dillution refrigerator at the High BT Facility Equipment at the High BT Facility. magnetization...

70

High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems  

Energy.gov (U.S. Department of Energy (DOE))

High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems presentation at the April 2013 peer review meeting held in Denver, Colorado.

71

HighEnergy International  

E-Print Network (OSTI)

Jet Production at HERA Sascha Caron, I. Phys. Institut, RWTH Aachen High­Energy Physics r ) and d?? # e,i = # # n=1 # n s (µ r )C n (µ r ) # extract # s , pdfs? QCD Montpellier 2002, Sascha­jets above E T treshhold. DIS: find jets in ``Breit frame'': 2xP + q = 0 p r q g # maximal separation between

72

High speed door assembly  

SciTech Connect

This invention is comprised of a high speed door assembly, comprising an actuator cylinder and piston rods, a pressure supply cylinder and fittings, an electrically detonated explosive bolt, a honeycomb structured door, a honeycomb structured decelerator, and a structural steel frame encasing the assembly to close over a 3 foot diameter opening within 50 milliseconds of actuation, to contain hazardous materials and vapors within a test fixture.

Shapiro, C.

1991-12-31T23:59:59.000Z

73

High voltage pulse conditioning  

DOE Patents (OSTI)

Apparatus for conditioning high voltage pulses from particle accelerators in order to shorten the rise times of the pulses. Flashover switches in the cathode stalk of the transmission line hold off conduction for a determinable period of time, reflecting the early portion of the pulses. Diodes upstream of the switches divert energy into the magnetic and electrostatic storage of the capacitance and inductance inherent to the transmission line until the switches close.

Springfield, Ray M. (Sante Fe, NM); Wheat, Jr., Robert M. (Los Alamos, NM)

1990-01-01T23:59:59.000Z

74

High pressure ceramic joint  

DOE Patents (OSTI)

Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present joint when used with recuperators increases the use of ceramic components which do not react to highly corrosive gases. Thus, the present joint used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present joint is comprised of a first ceramic member, a second ceramic member, a mechanical locking device having a groove defined in one of the first ceramic member and the second ceramic member. The joint and the mechanical locking device is further comprised of a refractory material disposed in the groove and contacting the first ceramic member and the second ceramic member. The present joint mechanically provides a high strength load bearing joint having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures.

Ward, Michael E. (Poway, CA); Harkins, Bruce D. (San Diego, CA)

1993-01-01T23:59:59.000Z

75

High pressure ceramic joint  

DOE Patents (OSTI)

Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present joint when used with recuperators increases the use of ceramic components which do not react to highly corrosive gases. Thus, the present joint used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present joint is comprised of a first ceramic member, a second ceramic member, a mechanical locking device having a groove defined in one of the first ceramic member and the second ceramic member. The joint and the mechanical locking device is further comprised of a refractory material disposed in the groove and contacting the first ceramic member and the second ceramic member. The present joint mechanically provides a high strength load bearing joint having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures. 4 figures.

Ward, M.E.; Harkins, B.D.

1993-11-30T23:59:59.000Z

76

PROFILE OF A HIGH SCHOOL INTERN: JOSHUA BLOOM | Princeton Plasma Physics  

NLE Websites -- All DOE Office Websites (Extended Search)

PROFILE OF A HIGH SCHOOL INTERN: JOSHUA BLOOM PROFILE OF A HIGH SCHOOL INTERN: JOSHUA BLOOM June 15, 2013 Some students come into the high school internship program at PPPL already harboring an interest in plasma physics, knowing exactly what research they want to work on and what they want to learn. Others come in not really knowing what to expect. Josh Bloom, a graduating senior from West Windsor-Plainsboro High School North, falls into the latter category, coming into PPPL with not necessarily any particular interest in working with plasma physics, but just a desire to make the most out of his high school's Senior Option program, in which qualifying students are granted the opportunity to spend a portion of their last semester in professional internships. Josh's interests in science were not tailored specifically to plasma

77

High Performance Computing School COMSC  

E-Print Network (OSTI)

High Performance Computing School COMSC This module aims to provide the students with fundamental knowledge and understanding of techniques associated with High Performance Computing and its practical' skills in analysing and evaluating High Performance Computing and will be structured around

Martin, Ralph R.

78

High Performance Computing (HPC) Division  

NLE Websites -- All DOE Office Websites (Extended Search)

HPC Division High Performance Computing (HPC) Division Providing world-class high performance computing capability that enables unsurpassed solutions to complex problems of...

79

High Temperature Membrane Working Group  

Energy.gov (U.S. Department of Energy (DOE))

The High Temperature Membrane Working Group consists of government, industry, and university researchers interested in developing high temperature membranes for fuel cells.

80

LANL | Physics | High Energy Physics  

NLE Websites -- All DOE Office Websites (Extended Search)

high energy physics frontiers as defined by the Department of Energy's Office of High Energy Physics. Exploring the intensity frontier On the trail of one of the greatest...

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

High School Students' Modeling Knowledge High School Students' Modeling Knowledge  

E-Print Network (OSTI)

High School Students' Modeling Knowledge High School Students' Modeling Knowledge David Fortus of the authors. #12;High School Students' Modeling Knowledge Abstract Modeling is a core scientific practice. This study probed the modeling knowledge of high school students who had not any explicit exposure

82

High temperature detonator  

DOE Patents (OSTI)

A detonator assembly is provided which is usable at high temperatures about 300.degree. C. A detonator body is provided with an internal volume defining an anvil surface. A first acceptor explosive is disposed on the anvil surface. A donor assembly having an ignition element, an explosive material, and a flying plate, are placed in the body effective to accelerate the flying plate to impact the first acceptor explosive on the anvil for detonating the first acceptor explosive. A second acceptor explosive is eccentrically located in detonation relationship with the first acceptor explosive to thereafter effect detonation of a main charge.

Johnson, James O. (Los Alamos, NM); Dinegar, Robert H. (Los Alamos, NM)

1988-01-01T23:59:59.000Z

83

Theoretical High Energy Physics  

SciTech Connect

we provide reports from each of the six faculty supported by the Department of Energy High Energy Physics Theory grant at Columbia University. Each is followed by a bibliography of the references cited. A complete list of all of the publications in the 12/1/2010-04/30/2014 period resulting from research supported by this grant is provided in the following section. The final section lists the Ph.D. dissertations based on research supported by the grant that were submitted during this period.

Christ, Norman H.; Weinberg, Erick J.

2014-07-14T23:59:59.000Z

84

High-energy  

NLE Websites -- All DOE Office Websites (Extended Search)

0 0 22. High-energy collider parameters HIGH-ENERGY COLLIDER PARAMETERS: e + e - Colliders (I) The numbers here were received from representatives of the colliders in late 1999 (contact C.G. Wohl, LBNL). Many of the numbers of course change with time, and only the latest values (or estimates) are given here; those in brackets are for coming upgrades. Quantities are, where appropriate, r.m.s. H and V indicate horizontal and vertical directions. Parameters for the defunct SPEAR, DORIS, PETRA, PEP, and TRISTAN colliders may be found in our 1996 edition (Phys. Rev. D54, 1 July 1996, Part I). VEPP-2M (Novosibirsk) VEPP-2000 ∗ (Novosibirsk) VEPP-4M (Novosibirsk) BEPC (China) DAΦNE (Frascati) Physics start date 1974 2001 1994 1989 1999 Maximum beam energy (GeV) 0.7 1.0 6 2.2 0.510 (0.75 max.) Luminosity (10 30 cm -2 s -1 ) 5 100 50 10 at 2 GeV 5 at 1.55 GeV 50(→500) Time between collisions (µs)

85

Highly Insulating Windows - Fram  

NLE Websites -- All DOE Office Websites (Extended Search)

Frames Frames Research performed at the Norwegian University of Science and Technology and LBNL has identified various highly insulating frame solutions. A report was released in 2007 describing some of these frames. This document reports the findings of a market and research review related to state-of-the-art highly insulating window frames. The market review focuses on window frames that satisfy the Passivhaus requirements (window U-value less or equal to 0.8 W/m2K ), while other examples are also given in order to show the variety of materials and solutions that may be used for constructing window frames with a low thermal transmittance (U-value). The market search shows that several combinations of materials are used in order to obtain window frames with a low U-value. The most common insulating material seems to be Polyurethane (PUR), which is used together with most of the common structural materials such as wood, aluminum, and PVC.

86

High throughput optical scanner  

DOE Patents (OSTI)

A scanning apparatus is provided to obtain automated, rapid and sensitive scanning of substrate fluorescence, optical density or phosphorescence. The scanner uses a constant path length optical train, which enables the combination of a moving beam for high speed scanning with phase-sensitive detection for noise reduction, comprising a light source, a scanning mirror to receive light from the light source and sweep it across a steering mirror, a steering mirror to receive light from the scanning mirror and reflect it to the substrate, whereby it is swept across the substrate along a scan arc, and a photodetector to receive emitted or scattered light from the substrate, wherein the optical path length from the light source to the photodetector is substantially constant throughout the sweep across the substrate. The optical train can further include a waveguide or mirror to collect emitted or scattered light from the substrate and direct it to the photodetector. For phase-sensitive detection the light source is intensity modulated and the detector is connected to phase-sensitive detection electronics. A scanner using a substrate translator is also provided. For two dimensional imaging the substrate is translated in one dimension while the scanning mirror scans the beam in a second dimension. For a high throughput scanner, stacks of substrates are loaded onto a conveyor belt from a tray feeder.

Basiji, David A. (Seattle, WA); van den Engh, Gerrit J. (Seattle, WA)

2001-01-01T23:59:59.000Z

87

High Performance Window Retrofit  

SciTech Connect

The US Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE) and Traco partnered to develop high-performance windows for commercial building that are cost-effective. The main performance requirement for these windows was that they needed to have an R-value of at least 5 ft2 F h/Btu. This project seeks to quantify the potential energy savings from installing these windows in commercial buildings that are at least 20 years old. To this end, we are conducting evaluations at a two-story test facility that is representative of a commercial building from the 1980s, and are gathering measurements on the performance of its windows before and after double-pane, clear-glazed units are upgraded with R5 windows. Additionally, we will use these data to calibrate EnergyPlus models that we will allow us to extrapolate results to other climates. Findings from this project will provide empirical data on the benefits from high-performance windows, which will help promote their adoption in new and existing commercial buildings. This report describes the experimental setup, and includes some of the field and simulation results.

Shrestha, Som S [ORNL] [ORNL; Hun, Diana E [ORNL] [ORNL; Desjarlais, Andre Omer [ORNL] [ORNL

2013-12-01T23:59:59.000Z

88

High temperature thermometric phosphors  

DOE Patents (OSTI)

A high temperature phosphor consists essentially of a material having the general formula LuPO.sub.4 :Dy.sub.(x),Eu.sub.y) wherein: 0.1 wt %.ltoreq.x.ltoreq.20 wt % and 0.1 wt %.ltoreq.y.ltoreq.20 wt %. The high temperature phosphor is in contact with an article whose temperature is to be determined. The article having the phosphor in contact with it is placed in the environment for which the temperature of the article is to be determined. The phosphor is excited by a laser causing the phosphor to fluoresce. The emission from the phosphor is optically focused into a beam-splitting mirror which separates the emission into two separate emissions, the emission caused by the dysprosium dopant and the emission caused by the europium dopent. The separated emissions are optically filtered and the intensities of the emission are detected and measured. The ratio of the intensity of each emission is determined and the temperature of the article is calculated from the ratio of the intensities of the separate emissions.

Allison, Stephen W. (Knoxville, TN); Cates, Michael R. (Oak Ridge, TN); Boatner, Lynn A. (Oak Ridge, TN); Gillies, George T. (Earlysville, VA)

1999-03-23T23:59:59.000Z

89

High Performance Buildings Database  

DOE Data Explorer (OSTI)

The High Performance Buildings Database is a shared resource for the building industry, a unique central repository of in-depth information and data on high-performance, green building projects across the United States and abroad. The database includes information on the energy use, environmental performance, design process, finances, and other aspects of each project. Members of the design and construction teams are listed, as are sources for additional information. In total, up to twelve screens of detailed information are provided for each project profile. Projects range in size from small single-family homes or tenant fit-outs within buildings to large commercial and institutional buildings and even entire campuses. The database is a data repository as well. A series of Web-based data-entry templates allows anyone to enter information about a building project into the database. Once a project has been submitted, each of the partner organizations can review the entry and choose whether or not to publish that particular project on its own Web site.

90

High speed transient sampler  

DOE Patents (OSTI)

A high speed sampler comprises a meandered sample transmission line for transmitting an input signal, a straight strobe transmission line for transmitting a strobe signal, and a plurality of sampling gates along the transmission lines. The sampling gates comprise a four terminal diode bridge having a first strobe resistor connected from a first terminal of the bridge to the positive strobe line, a second strobe resistor coupled from the third terminal of the bridge to the negative strobe line, a tap connected to the second terminal of the bridge and to the sample transmission line, and a sample holding capacitor connected to the fourth terminal of the bridge. The resistance of the first and second strobe resistors is much higher than the signal transmission line impedance in the preferred system. This results in a sampling gate which applies a very small load on the sample transmission line and on the strobe generator. The sample holding capacitor is implemented using a smaller capacitor and a larger capacitor isolated from the smaller capacitor by resistance. The high speed sampler of the present invention is also characterized by other optimizations, including transmission line tap compensation, stepped impedance strobe line, a multi-layer physical layout, and unique strobe generator design. A plurality of banks of such samplers are controlled for concatenated or interleaved sample intervals to achieve long sample lengths or short sample spacing. 17 figs.

McEwan, T.E.

1995-11-28T23:59:59.000Z

91

High speed transient sampler  

DOE Patents (OSTI)

A high speed sampler comprises a meandered sample transmission line for transmitting an input signal, a straight strobe transmission line for transmitting a strobe signal, and a plurality of sampling gates along the transmission lines. The sampling gates comprise a four terminal diode bridge having a first strobe resistor connected from a first terminal of the bridge to the positive strobe line, a second strobe resistor coupled from the third terminal of the bridge to the negative strobe line, a tap connected to the second terminal of the bridge and to the sample transmission line, and a sample holding capacitor connected to the fourth terminal of the bridge. The resistance of the first and second strobe resistors is much higher than the signal transmission line impedance in the preferred system. This results in a sampling gate which applies a very small load on the sample transmission line and on the strobe generator. The sample holding capacitor is implemented using a smaller capacitor and a larger capacitor isolated from the smaller capacitor by resistance. The high speed sampler of the present invention is also characterized by other optimizations, including transmission line tap compensation, stepped impedance strobe line, a multi-layer physical layout, and unique strobe generator design. A plurality of banks of such samplers are controlled for concatenated or interleaved sample intervals to achieve long sample lengths or short sample spacing.

McEwan, Thomas E. (Livermore, CA)

1995-01-01T23:59:59.000Z

92

High Temperature Membrane Working Group  

Energy.gov (U.S. Department of Energy (DOE))

This presentation provides an overview of the High Temperature Membrane Working Group Meeting in May 2007.

93

Y High-Resolution  

NLE Websites -- All DOE Office Websites (Extended Search)

Y Y High-Resolution . __ DO NOT M I C PET COVER for medical science studies Lawrence Berkeley Laboratory University of California September 1989 DlSTRlBUTlGN OF THIS DOCUMENT IS U#LIIY/ITEE Acknowledgments This booklet was prepared under the sponsorship of the U.S. Department of Energy Office of Health Effects Research, the National Institutes of Health, and the Lawrence Berkeley Laboratory's Research Medicine and Radiation Biophysics Division. We thank Sarah Cahn and Douglas Vaughan for coordination of this booklet. esolution PET for Medical Science Studies Thomas F. Budinger Stephen E. Derenzo Ronald H. Huesman William J. Jagust Peter E. Valk CONTENTS A PET Primer Positron Emission Tomography: Evolution of a Technology 7 PET Theory: Emission, Detection, and Reconstruction

94

Highly Insulating Windows - Publ  

NLE Websites -- All DOE Office Websites (Extended Search)

Highly Insulating Windows - Publications Future Advanced Windows for Zero-Energy Homes, J. Apte, D. Arasteh, J. Huang, 2003 ASHRAE Annual Meeting, 2002 Nine representative window products are examined in eight representative U.S. climates. Annual energy and peak demand impacts are investigated. We conclude that a new generation of window products is necessary for zero-energy homes if windows are not to be an energy drain on these homes. Performance Criteria for Residential Zero Energy Windows, D. Arasteh, H. Goudey, J. Huang, C. Kohler, R. Mitchell, 2006, submitted to ASHRAE Through the use of whole house energy modeling, typical efficient products are evaluated in five US climates and compared against the requirements for ZEHs. Products which meet these needs are defined as a function of climate.

95

High energy physics  

SciTech Connect

Hadron collider studies will focus on: (i) the search for the top quark with the newly installed D0 detector at the Fermilab Tevatron collider, (ii) the upgrade of the D0 detector to match the new main injector luminosity and (iii) R&D on silicon microstrip tracking devices for the SSC. High statistics studies of Z{sup 0} decay will continue with the OPAL detector at LEP. These studies will include a direct measurement of Z decay to neutrinos, the search for Higgs and heavy quark decays of Z. Preparations for the Large Scintillation Neutrino Detector (LSND) to measure neutrino oscillations at LAMPF will focus on data acquisition and testing of photomultiplier tubes. In the theoretical area E. Ma will concentrate on mass-generating radiative mechanisms for light quarks and leptons in renormalizable gauge field theories. J. Wudka`s program includes a detailed investigation of the magnetic-flip approach to the solar neutrino.

Kernan, A.; Shen, B.C.; Ma, E.

1997-07-01T23:59:59.000Z

96

HIGH PERFORMANCE COMPUTING  

E-Print Network (OSTI)

This paper presents recent developments of high performance computing and networking techniques in the field of computer-aided multibody analysis and design. The authors describe the main achievements obtained in the development of a tool to aid in the design of new industrial mechanical systems by performing parallel parametric multibody simulations. The parallel software is composed of four main modules: two user-friendly interfaces to input the data and visualize the results, a simulation module, and a parallel manager module that is the main focus of this paper. The authors show that the implementation, using PVM, of simple and well-known ideas leads to efficient and flexible parallel software targeted for heterogeneous networks of nondedicated workstations, which is the parallel platform available in most mechanical design departments.

Ra Baldini; Luc Giraud; Javier G. Izaguirre; Jose M. Jimenez; Luis M. Matey; Sandra Baldini; Luc Giraud; Javier G. Izaguirre; Jose M. Jimenez; Luis M. Matey

97

Senior Director Student Development  

E-Print Network (OSTI)

Senior Director Student Development & Services Janet Teasdale Assistant to the Vice President, Conferences & Food Operations (dual campus) Andrew Parr Chaplains Roberta Fraser Inter-Fraternity & Panhellenic Community Service Learning Margot Fryer Alma Mater Society UBCV Graduate Student Society UBCV

Michelson, David G.

98

High pressure--high temperature research using high energy synchrotron radiation at the TRISTAN accumulation ring  

SciTech Connect

High energy synchrotron radiation emitted from the bending magnet of the TRISTAN accumulation ring (6.5 GeV) at the National Laboratory for High Energy Physics has been used for the high pressure--high temperature diffraction experiments using a multianvil press system, MAX80. Owing to the specific features of high energy synchroton radiation, significant improvements have been brought to the high pressure research. The wide energy range of diffraction spectrum leads to an increase in the number of observable diffraction peaks in an energy-dispersive method, resulting in an increase in the accuracy of the measurements of the lattice and thermal parameters. Due to the high penetrating power of radiation, diffraction patterns can be taken in a short time from materials containing heavy elements or materials surrounded by a metal foil. Typical examples of high pressure--high temperature experiments with high energy synchrotron radiation are also described.

Kikegawa, T.; Shimomura, O.; Iwasaki, H.; Sato, S.; Mikuni, A.; Iida, A.; Kamiya, N.

1989-07-01T23:59:59.000Z

99

High Temperature Corrosion Test Facilities and High Pressure Test  

NLE Websites -- All DOE Office Websites (Extended Search)

High Temperature High Temperature Corrosion Test Facilities and High Pressure Test Facilities for Metal Dusting Test Facilities for Metal Dusting Overview Other Facilities Work with Argonne Contact us For Employees Site Map Help Join us on Facebook Follow us on Twitter NE on Flickr High Temperature Corrosion Test Facilities and High Pressure Test Facilities for Metal Dusting Six corrosion test facilities and two thermogravimetric systems for conducting corrosion tests in complex mixed gas environments, in steam and in the presence of deposits, and five facilities for metal dusting degradation Bookmark and Share The High Temperature Corrosion Test Facilities and High Pressure Test Facilities for Metal Dusting include: High Pressure Test Facility for Metal Dusting Resistance:

100

High Energy Density Science with High Peak Power Light Sources  

Science Journals Connector (OSTI)

High energy density (HED) science is a growing sub-field of plasma and condensed matter physics. I will examine how recent technological developments in high peak power, petawatt-class...

Ditmire, Todd

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Energy Efficiency Indicators for High Electric-Load Buildings  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Efficiency Indicators for High Electric-Load Buildings Energy Efficiency Indicators for High Electric-Load Buildings Speaker(s): Bernard Aebischer Date: February 6, 2003 - 12:00pm Location: Bldg. 90 Seminar Host/Point of Contact: Kristina LaCommare Energy per unit of floor area is not an adequate indictor for energy efficiency in high electric-load buildings. For two activities, restaurants and computer centres, alternative indicators for energy efficiency are discussed. Prerequisites in order to be able to use these indicators in energy efficiency programmes are discussed. The opportunity of an internationally coordinated research activity is also presented. Since 1999, Dr. Bernard Aebischer has served as a senior scientist at CEPE (Centre for Energy Policy and Economics) of the Swiss Federal Institutes of

102

High power connection system  

DOE Patents (OSTI)

A high power connection system adapted for automotive environments which provides environmental and EMI shielding includes a female connector, a male connector, and a panel mount. The female connector includes a female connector base and a snap fitted female connector cover. The male connector includes a male connector base and a snap fitted male connector cover. The female connector base has at least one female power terminal cavity for seatably receiving a respective female power terminal. The male connector base has at least one male power terminal cavity for seatably receiving a respective male power terminal. The female connector is covered by a cover seal and a conductive shroud. A pair of lock arms protrude outward from the front end of the male connector base, pass through the panel mount and interface with a lever of a lever rotatably connected to the shroud to thereby mechanically assist mating of the male and female connectors. Safety terminals in the male and female connectors provide a last-to-connect-first-to-break connection with an HVIL circuit.

Schaefer, Christopher E. (Warren, OH); Beer, Robert C. (Noblesville, IN); McCall, Mark D. (Youngstown, OH)

2000-01-01T23:59:59.000Z

103

UESC and High Tech Facilities  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Federal Energy Management Program UESC and High Tech Facilities Charles Williams, Lawrence Berkeley National Lab 2 | FUPWG April 2012 High Tech Building UESC Partnership Leveraging Technical Potential, Market Opportunity, Program Resources * Energy-intensive facilities with high savings potential * PG&E service territory - high concentration of high-technology buildings * PG&E UESC program, new and growing * DOE FEMP programs for UESC and High-Tech Buildings * LBNL expertise in labs, data centers, clean rooms * LBNL support for UESC program * UESC potential for innovation * Presidential "We Can't Wait $2 Billion challenge to Federal agencies 3 | FUPWG April 2012 UESC project support at LBNLL Training /Education

104

POLICY PERSPECTIVE High Conservation Value or high confusion value? Sustainable  

E-Print Network (OSTI)

and biodiversity conservation in the tropics David P. Edwards1 , Brendan Fisher1 , & David S. Wilcove2 1 WoodrowPOLICY PERSPECTIVE High Conservation Value or high confusion value? Sustainable agriculture certifies timber that is harvested to manage and maintain forests defined as having High Conservation Value

Vermont, University of

105

1International High Speed Rail Conference 19642064 High Speed Rail  

E-Print Network (OSTI)

1International High Speed Rail Conference 1964­2064 High Speed Rail: Celebrating Ambition 2014 by the Birmingham Centre for Railway Research and Education Conference programme 8 ­10 December 2014 Kindly supported by: #12;2 International High Speed Rail Conference Monday 8 December 12:00 ­ 12:50 Registration

Birmingham, University of

106

High density Integrated Optoelectronic Circuits for High Speed Photonic Microsystems  

E-Print Network (OSTI)

High density Integrated Optoelectronic Circuits for High Speed Photonic Microsystems K. Minoglou.minoglou@imel.demorkitos.gr Abstract. The study of high density integrated optoelectronic circuits involves the development of hybrid integration technologies and the generation of models for the optoelectronic devices. To meet these goals

Kouroupetroglou, Georgios

107

High Average Power, High Energy Short Pulse Fiber Laser System  

SciTech Connect

Recently continuous wave fiber laser systems with output powers in excess of 500W with good beam quality have been demonstrated [1]. High energy, ultrafast, chirped pulsed fiber laser systems have achieved record output energies of 1mJ [2]. However, these high-energy systems have not been scaled beyond a few watts of average output power. Fiber laser systems are attractive for many applications because they offer the promise of high efficiency, compact, robust systems that are turn key. Applications such as cutting, drilling and materials processing, front end systems for high energy pulsed lasers (such as petawatts) and laser based sources of high spatial coherence, high flux x-rays all require high energy short pulses and two of the three of these applications also require high average power. The challenge in creating a high energy chirped pulse fiber laser system is to find a way to scale the output energy while avoiding nonlinear effects and maintaining good beam quality in the amplifier fiber. To this end, our 3-year LDRD program sought to demonstrate a high energy, high average power fiber laser system. This work included exploring designs of large mode area optical fiber amplifiers for high energy systems as well as understanding the issues associated chirped pulse amplification in optical fiber amplifier systems.

Messerly, M J

2007-11-13T23:59:59.000Z

108

Ultra high vacuum broad band high power microwave window  

DOE Patents (OSTI)

An improved high vacuum microwave window has been developed that utilizes high density polyethylene coated on two sides with SiOx, SiNx, or a combination of the two. The resultant low dielectric and low loss tangent window creates a low outgassing, low permeation seal through which broad band, high power microwave energy may be passed. No matching device is necessary and the sealing technique is simple. The features of the window are broad band transmission, ultra-high vacuum compatibility with a simple sealing technique, low voltage standing wave ratio, high power transmission and low cost.

Nguyen-Tuong, Viet (Seaford, VA); Dylla, III, Henry Frederick (Yorktown, VA)

1997-01-01T23:59:59.000Z

109

Ultra high vacuum broad band high power microwave window  

DOE Patents (OSTI)

An improved high vacuum microwave window has been developed that utilizes high density polyethylene coated on two sides with SiOx, SiNx, or a combination of the two. The resultant low dielectric and low loss tangent window creates a low outgassing, low permeation seal through which broad band, high power microwave energy may be passed. No matching device is necessary and the sealing technique is simple. The features of the window are broad band transmission, ultra-high vacuum compatibility with a simple sealing technique, low voltage standing wave ratio, high power transmission and low cost. 5 figs.

Nguyen-Tuong, V.; Dylla, H.F. III

1997-11-04T23:59:59.000Z

110

High repetition rate fiber lasers  

E-Print Network (OSTI)

This thesis reports work in high repetition rate femtosecond fiber lasers. Driven by the applications including optical arbitrary waveform generation, high speed optical sampling, frequency metrology, and timing and frequency ...

Chen, Jian, Ph. D. Massachusetts Institute of Technology

2009-01-01T23:59:59.000Z

111

High intensity femtosecond enhancement cavities  

E-Print Network (OSTI)

To produce extreme ultraviolet radiation via high harmonic generation (HHG) in rare gases, light intensities in excess of 1014 W/cm 2 are required. Usually such high intensity are obtained by parametric amplification of ...

Abram, Gilberto

2009-01-01T23:59:59.000Z

112

High-Pressure Hydrogen Tanks  

Energy.gov (U.S. Department of Energy (DOE))

Presentation on High-Pressure Hydrogen Tanks for the DOE Hydrogen Delivery High-Pressure Tanks and Analysis Project Review Meeting held February 8-9, 2005 at Argonne National Laboratory

113

High flux compact neutron generators  

E-Print Network (OSTI)

High Flux Compact Neutron Generators J. Reijonen ,1 , T-Compact high flux neutron generators are developed at thevoltage feed through of the generator is shown in Fig. 4.

Reijonen, J.; Lou, T.-P.; Tolmachoff, B.; Leung, K.-N.; Verbeke, J.; Vujic, J.

2001-01-01T23:59:59.000Z

114

Highly linear low noise amplifier  

E-Print Network (OSTI)

, the Low Noise Amplifier (LNA) is expected to provide high linearity, thus preventing the intermodulation tones created by the interference signal from corrupting the carrier signal. The research focuses on designing a novel LNA which achieves high...

Ganesan, Sivakumar

2007-09-17T23:59:59.000Z

115

High-Temperature Water Splitting  

Energy.gov (U.S. Department of Energy (DOE))

High-temperature water splitting (a "thermochemical" process) is a long-term technology in the early stages of development.

116

High Performance Computing contributions to  

E-Print Network (OSTI)

High Performance Computing contributions to DoD Mission Success 2002 #12;Approved for public/C nanotube in a field emitter configuration #12;HIGH PERFORMANCE COMPUTING contributions tocontributions ­ SECTION 1 INTRODUCTION 1 Introduction 3 Overview of the High Performance Computing Modernization Program 3

117

High Performance and Sustainable Buildings Guidance | Department...  

Energy Savers (EERE)

High Performance and Sustainable Buildings Guidance High Performance and Sustainable Buildings Guidance High Performance and Sustainable Buildings Guidance More Documents &...

118

High-Temperature-High-Volume Lifting | Open Energy Information  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » High-Temperature-High-Volume Lifting Jump to: navigation, search Geothermal ARRA Funded Projects for High-Temperature-High-Volume Lifting Loading map... {"format":"googlemaps3","type":"ROADMAP","types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"limit":200,"offset":0,"link":"all","sort":[""],"order":[],"headers":"show","mainlabel":"","intro":"","outro":"","searchlabel":"\u2026

119

High Temperature, High Pressure Devices for Zonal Isolation in...  

Open Energy Info (EERE)

remotely and autonomous deployable structures for space and our high temperature composite technology developed for downhole applications. These devices offer several...

120

National High Magnetic Field Laboratory: DC Field Facility: High...  

NLE Websites -- All DOE Office Websites (Extended Search)

phase transitions High-resolution electron spin resonance (ESR) spectroscopy of transition metal ions (which is of great importance in chemistry, biochemistry and structural...

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

High Pressure Research Questionnaire National High Magnetic Field...  

NLE Websites -- All DOE Office Websites (Extended Search)

Pressure Research Questionnaire National High Magnetic Field Laboratory Operated by Florida State University, University of Florida, Los Alamos National Laboratory Florida State...

122

High-temperature Pump Monitoring - High-temperature ESP Monitoring...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Report Detecting Fractures Using Technology at High Temperatures and Depths - Geothermal Ultrasonic Fracture Imager (GUFI); 2010 Geothermal Technology Program Peer Review Report...

123

High-Temperature-High-Volume Lifting for Enhanced Geothermal...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Norman Turnquist GE Global Research High Temperature Tools and Sensors, Down-hole Pumps and Drilling May 19, 2010 This presentation does not contain any proprietary...

124

High resolution time interval meter  

DOE Patents (OSTI)

Method and apparatus are provided for measuring the time interval between two events to a higher resolution than reliability available from conventional circuits and component. An internal clock pulse is provided at a frequency compatible with conventional component operating frequencies for reliable operation. Lumped constant delay circuits are provided for generating outputs at delay intervals corresponding to the desired high resolution. An initiation START pulse is input to generate first high resolution data. A termination STOP pulse is input to generate second high resolution data. Internal counters count at the low frequency internal clock pulse rate between the START and STOP pulses. The first and second high resolution data are logically combined to directly provide high resolution data to one counter and correct the count in the low resolution counter to obtain a high resolution time interval measurement.

Martin, A.D.

1986-05-09T23:59:59.000Z

125

HIGHLY COMPRESSED ION BEAMS FOR HIGH ENERGY DENSITY SCIENCE  

E-Print Network (OSTI)

HIGHLY COMPRESSED ION BEAMS FOR HIGH ENERGY DENSITY SCIENCE A. Friedman1,2 , J.J.Barnard1,2 , R Energy Density regimes required for Inertial Fu- sion Energy and other applications. An interim goal we are pursuing, low to medium mass ions with energies just above the Bragg peak are directed onto

Wurtele, Jonathan

126

High-power, high-intensity laser propagation and interactions  

SciTech Connect

This paper presents overviews of a number of processes and applications associated with high-power, high-intensity lasers, and their interactions. These processes and applications include: free electron lasers, backward Raman amplification, atmospheric propagation of laser pulses, laser driven acceleration, atmospheric lasing, and remote detection of radioactivity. The interrelated physical mechanisms in the various processes are discussed.

Sprangle, Phillip [Plasma Physics Division, Naval Research Laboratory, Washington, DC 20375 (United States); Electrical and Computer Engineering and Physics, University of Maryland, College Park, Maryland 20740 (United States); Hafizi, Bahman [Plasma Physics Division, Naval Research Laboratory, Washington, DC 20375 (United States)

2014-05-15T23:59:59.000Z

127

Long, Highly-Ordered High-Temperature Superconductor Nanowire Arrays  

Science Journals Connector (OSTI)

Long, Highly-Ordered High-Temperature Superconductor Nanowire Arrays ... For bulk superconductors, the electrical resistance drops precipitously to zero below the superconducting transition temperature (Tc). ... Even these temperatures are considerably higher than those found in conventional superconductor NWs of similar widths, which are typically below liquid helium temperature (4.2 K). ...

Ke Xu; James R. Heath

2008-10-28T23:59:59.000Z

128

Results from high energy accelerators  

E-Print Network (OSTI)

We review some of the recent experimental results obtained at high-energy colliders with emphasis on LEP and SLC results.

G. Giacomelli; B. Poli

2002-02-11T23:59:59.000Z

129

High field gradient particle accelerator  

DOE Patents (OSTI)

A high electric field gradient electron accelerator utilizing short duration, microwave radiation, and capable of operating at high field gradients for high energy physics applications or at reduced electric field gradients for high average current intermediate energy accelerator applications is disclosed. Particles are accelerated in a smooth bore, periodic undulating waveguide, wherein the period is so selected that the particles slip an integral number of cycles of the r.f. wave every period of the structure. This phase step of the particles produces substantially continuous acceleration in a traveling wave without transverse magnetic or other guide means for the particle. 10 figs.

Nation, J.A.; Greenwald, S.

1989-05-30T23:59:59.000Z

130

High field gradient particle accelerator  

DOE Patents (OSTI)

A high electric field gradient electron accelerator utilizing short duration, microwave radiation, and capable of operating at high field gradients for high energy physics applications or at reduced electric field gradients for high average current intermediate energy accelerator applications. Particles are accelerated in a smooth bore, periodic undulating waveguide, wherein the period is so selected that the particles slip an integral number of cycles of the r.f. wave every period of the structure. This phase step of the particles produces substantially continuous acceleration in a traveling wave without transverse magnetic or other guide means for the particle.

Nation, John A. (Ithaca, NY); Greenwald, Shlomo (Haifa, IL)

1989-01-01T23:59:59.000Z

131

High Temperature Processing Symposium 2014  

E-Print Network (OSTI)

} High temperature recycling operations } Materials sustainability } New furnace technology (including solar) We look forward to seeing you in February 2014. Dr M Akbar Rhamdhani (Chairman HTPS 2014) Prof

Liley, David

132

SENIOR MEMBERS' RESEARCH INTERESTS 2012/13 NAME MAIN SUBJECT AREA OF SPECIAL INTEREST COLLEGE/FACULTY  

E-Print Network (OSTI)

dynamics, adolescent development Fellow, Senior Tutor College Awan, Dr Shakil Graphene high- speed electronics My research interests cover high-speed electronics based on a newly discovered material 'graphene resonance imaging (MRI) of inorganic chemical systems including wastewater treatment, Li-ion batteries

Cheng, Eugenia

133

Ferrin Moore, Senior Aviation Policy Officer  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ferrin Moore Ferrin Moore Title: Senior Aviation Policy Officer Organization: Office of Aviation Management/MA-30 Address: Headquarters, United States Department of Energy 1000 Independence Avenue S.W. Washington, D.C. 20585 E-mail Address: Ferrin.Moore@hq.doe.gov Phone Number: Office: (202) 586-6171, Mobile: Fax Number: (202) 586-6008 Biographical Summary: Ferrin Moore is a highly experience aviation manager and leader with 30 years of aviation experience in the private and government sector. Prior to joining the Office of Aviation Management Ferrin served 15 years with the Federal Aviation Administration as an Aviation Safety Inspector and Manager. While in the private sector, he worked for United Airlines Maintenance Division in San Francisco and Washington D.C.

134

High Temperature, High Pressure Devices for Zonal Isolation in Geothermal  

Open Energy Info (EERE)

Temperature, High Pressure Devices for Zonal Isolation in Geothermal Temperature, High Pressure Devices for Zonal Isolation in Geothermal Wells Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title High Temperature, High Pressure Devices for Zonal Isolation in Geothermal Wells Project Type / Topic 1 Recovery Act: Enhanced Geothermal Systems Component Research and Development/Analysis Project Type / Topic 2 Zonal Isolation Project Description For Enhanced Geothermal Systems (EGS), high-temperature high-pressure zonal isolation tools capable of withstanding the downhole environment are needed. In these wells the packers must withstand differential pressures of 5,000 psi at more than 300°C, as well as pressures up to 20,000 psi at 200°C to 250°C. Furthermore, when deployed these packers and zonal isolation tools must form a reliable seal that eliminates fluid loss and mitigates short circuiting of flow from injectors to producers. At this time, general purpose open-hole packers do not exist for use in geothermal environments, with the primary technical limitation being the poor stability of existing elastomeric seals at high temperatures.

135

High-Temperature-High-Volume Lifting For Enhanced Geothermal Systems  

Open Energy Info (EERE)

Temperature-High-Volume Lifting For Enhanced Geothermal Systems Temperature-High-Volume Lifting For Enhanced Geothermal Systems Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title High-Temperature-High-Volume Lifting For Enhanced Geothermal Systems Project Type / Topic 1 Recovery Act: Enhanced Geothermal Systems Component Research and Development/Analysis Project Type / Topic 2 High-Temperature-High-Volume Lifting Project Description The proposed scope of work is divided into three Phases. Overall system requirements will be established in Phase 1, along with an evaluation of existing lifting system capability, identification of technology limitations, and a conceptual design of an overall lifting system. In developing the system components in Phase 2, component-level tests will be conducted using GE facilities. Areas of development will include high-temperature drive system materials, journal and thrust bearings, and corrosion and erosion-resistant lifting pump components. Finally, in Phase 3, the overall lab-scale lifting system will be demonstrated in a flow loop that will be constructed at GE Global Research.

136

In today's highly competitive marketplace,  

NLE Websites -- All DOE Office Websites (Extended Search)

today's highly competitive marketplace, rapid creation today's highly competitive marketplace, rapid creation and commercialization of scientific advances and innovative technologies are key to the continued prosperity of the United States. Scientists and engineers at Lawrence Livermore National Laboratory (LLNL) have achieved numerous science and technology breakthroughs that have led to new industries, spurred economic growth and benefited the national welfare.

137

Ultra High Energy Cosmic Rays  

Science Journals Connector (OSTI)

We discuss briefly the phenomenon of the Ultra High Energy Cosmic Rays (UHECR) particles of energy approaching and exceeding 1011 GeV. The world experimental statistics contains a small number of events but their existence is a puzzle. Its solution may lead to exciting discoveries in high energy particle astrophysics as well as in particle physics and astronomy.

Todor Stanev

2004-01-01T23:59:59.000Z

138

Temperature controlled high voltage regulator  

DOE Patents (OSTI)

A temperature controlled high voltage regulator for automatically adjusting the high voltage applied to a radiation detector is described. The regulator is a solid state device that is independent of the attached radiation detector, enabling the regulator to be used by various models of radiation detectors, such as gas flow proportional radiation detectors.

Chiaro, Jr., Peter J. (Clinton, TN); Schulze, Gerald K. (Knoxville, TN)

2004-04-20T23:59:59.000Z

139

High temperature lightweight foamed cements  

DOE Patents (OSTI)

Cement slurries are disclosed which are suitable for use in geothermal wells since they can withstand high temperatures and high pressures. The formulation consists of cement, silica flour, water, a retarder, a foaming agent, a foam stabilizer, and a reinforcing agent. A process for producing these cements is also disclosed. 3 figs.

Sugama, Toshifumi.

1989-10-03T23:59:59.000Z

140

Electrokinetically pumped high pressure sprays  

DOE Patents (OSTI)

An electrokinetic pump capable of producing high pressure is combined with a nozzle having a submicron orifice to provide a high pressure spray device. Because of its small size, the device can be contained within medical devices such as an endoscope for delivering biological materials such as DNA, chemo therapeutic agents, or vaccines to tissues and cells.

Schoeniger, Joseph S. (Oakland, CA); Paul, Phillip H. (Livermore, CA); Schoeniger, Luke (Pittsford, NY)

2005-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Fundamentals of high pressure adsorption  

SciTech Connect

High-pressure adsorption attracts research interests following the world's attention to alternative fuels, and it exerts essential effect on the study of hydrogen/methane storage and the development of novel materials addressing to the storage. However, theoretical puzzles in high-pressure adsorption hindered the progress of application studies. Therefore, the present paper addresses the major theoretical problems that challenged researchers: i.e., how to model the isotherms with maximum observed in high-pressure adsorption; what is the adsorption mechanism at high pressures; how do we determine the quantity of absolute adsorption based on experimental data. Ideology and methods to tackle these problems are elucidated, which lead to new insights into the nature of high-pressure adsorption and progress in application studies, for example, in modeling multicomponent adsorption, hydrogen storage, natural gas storage, and coalbed methane enrichment, was achieved.

Zhou, Y.P.; Zhou, L. [Tianjin University, Tianjin (China). High Pressure Adsorption Laboratory

2009-12-15T23:59:59.000Z

142

High Temperature | Open Energy Information  

Open Energy Info (EERE)

Temperature Temperature Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Print PDF Sanyal Temperature Classification: High Temperature Dictionary.png High Temperature: No definition has been provided for this term. Add a Definition Sanyal Temp Classification This temperature scheme was developed by Sanyal in 2005 at the request of DOE and GEA, as reported in Classification of Geothermal Systems: A Possible Scheme. Extremely Low Temperature Very Low Temperature Low Temperature Moderate Temperature High Temperature Ultra High Temperature Steam Field Reservoir fluid between 230°C and 300°C is considered by Sanyal to be "high temperature." "Above a temperature level of 230°C, the reservoir would be expected to become two-phase at some point during exploitation. The next higher

143

High Technology and Industrial Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Semiconductor clean room Semiconductor clean room High Technology and Industrial Systems EETD's research on high technology buildings and industrial systems is aimed at reducing energy consumed by the industrial sector in manufacturing facilities, including high technology industries such as data centers, cleanrooms in the such industries as electronics and pharmaceutical manufacturing, and laboratories, improving the competitiveness of U.S. industry. Contacts William Tschudi WFTschudi@lbl.gov (510) 495-2417 Aimee McKane ATMcKane@lbl.gov (518) 782-7002 Links High-Performance Buildings for High-Tech Industries Industrial Energy Analysis Batteries and Fuel Cells Buildings Energy Efficiency Applications Commercial Buildings Cool Roofs and Heat Islands Demand Response Energy Efficiency Program and Market Trends

144

High Bandgap III-V Alloys for High Efficiency Optoelectronics...  

NLE Websites -- All DOE Office Websites (Extended Search)

bandgap alloys for high efficiency optoelectronics are disclosed. An exemplary optoelectronic device may include a substrate, at least one Al.sub.1-xIn.sub.xP layer, and a...

145

high  

Gasoline and Diesel Fuel Update (EIA)

December 1999 December 1999 Highlights International Oil Markets Prices. World oil prices for the remainder of 1999 and all of 2000 are expected to remain above $20 per barrel. EIA believes that prices will rise from average November levels (an estimated $23.50 per barrel for the price paid by U.S. refiners for imported crude) by about $1 per barrel by December, due to increased demand in the winter and Y2K precautionary building of end-user inventories (see a brief discussion on Y2K impacts below). The world oil price is then expected to dip slightly to an average of $24.00 per barrel in January 2000 as the peak of the winter stock build passes before gradually declining to $20.50 per barrel by December 2000. This forecast assumes that OPEC compliance remains relatively strong

146

HIGH  

Gasoline and Diesel Fuel Update (EIA)

000 000 Highlights International Oil Markets Prices. We have found little need to adjust our oil price forecast from last month's report, since no evidence of significantly more bullish (or bearish) sentiment on the world oil market has arisen since last month. Our estimate from the December Outlook for the November imported oil cost still looks good at $23.50 and our current estimate for December's price at $24.75 is only slightly above last month's expected December level ($24.50). Thus, annual average prices remain, in our view, on a pace to show $5-per- barrel increases in both 1999 and 2000 (Figure 1). This pattern masks the more salient aspect of the forecast, which calls for steadily (but gradually) declining prices through 2000 and into 2001 when looking ahead by month from where we are today (Figure 2).

147

High  

NLE Websites -- All DOE Office Websites (Extended Search)

the pitch of B (r), and B(r), flips toroidally, such that the unidirectional toroidal electric field drives current in opposite directions, with respect to B, in the regions...

148

High-Performance Nanostructured Coating  

Energy.gov (U.S. Department of Energy (DOE))

The High-Performance Nanostructured Coating fact sheet details a SunShot project led by a University of California, San Diego research team working to develop a new high-temperature spectrally selective coating for receiver surfaces. These receiver surfaces, used in concentrating solar power systems, rely on high-temperature SSCs to effectively absorb solar energy without emitting much blackbody radiation.The optical properties of the SSC directly determine the efficiency and maximum attainable temperature of solar receivers, which in turn influence the power-conversion efficiency and overall system cost.

149

High Energy Cost Grants | Department of Energy  

Energy Savers (EERE)

High Energy Cost Grants High Energy Cost Grants The High Energy Cost Grant Program provides financial assistance for the improvement of energy generation, transmission, and...

150

OCIO Technology Summit: High Performance Computing | Department...  

NLE Websites -- All DOE Office Websites (Extended Search)

OCIO Technology Summit: High Performance Computing OCIO Technology Summit: High Performance Computing January 16, 2015 - 12:51pm Addthis OCIO Technology Summit: High Performance...

151

OCIO High Performance Computing Technology Summit | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

OCIO High Performance Computing Technology Summit OCIO High Performance Computing Technology Summit The OCIO High Performance Computing Technology Summit is on Wednesday, January...

152

Computational biology and high performance computing  

E-Print Network (OSTI)

Biology and High Performance Computing Manfred Zorn, TeresaBiology and High Performance Computing Presenters: Manfred99-Portland High performance computing has become one of the

Shoichet, Brian

2011-01-01T23:59:59.000Z

153

High Efficiency Particulate Air Filters  

NLE Websites -- All DOE Office Websites (Extended Search)

High Efficiency Particulate Air (HEPA) Filters High Efficiency Particulate Air (HEPA) Filters Home Standards DOE Workshops Nuclear Air Cleaning Conference Proceedings Qualified Filter List News Items Related Sites HEPA Related Lessons Learned Contact Us HSS Logo High Efficiency Particulate Air Filters The HEPA Filter web site provides a forum for informing and reporting department-wide activities related to filtration and ventilation issues with special reference to the High Efficiency Particulate Air (HEPA) Filters' use, inspection, and testing. This site contains essentials of DOE HEPA filter test program, procedures, requirements and quality assurance aspects applicable to HEPA filters used in DOE facilities. This site contains information about the DOE-accepted Filter Test Facility and its management, operation and quality assuranceprogram.

154

High-Pressure Hydrogen Tanks  

NLE Websites -- All DOE Office Websites (Extended Search)

February 8 February 8 th , 2005 Mark J. Warner, P.E. Principal Engineer Quantum Technologies, Inc. Irvine, CA Low Cost, High Efficiency, Low Cost, High Efficiency, High Pressure Hydrogen Storage High Pressure Hydrogen Storage This presentation does not contain any proprietary or confidential information. 70 MPa Composite Tanks Vent Line Ports Defueling Port (optional) Fill Port Filter Check Valve Vehicle Interface Bracket with Stone Shield In Tank Regulator with Solenoid Lock-off Pressure Relief Device Manual Valve Compressed Hydrogen Storage System In-Tank Regulator Pressure Sensor (not visible here) Pressure Relief Device (thermal) In Tank Gas Temperature Sensor Carbon Composite Shell (structural) Impact Resistant Outer Shell (damage resistant) Gas Outlet Solenoid Foam Dome (impact protection)

155

UESC and High Tech Facilities  

Energy.gov (U.S. Department of Energy (DOE))

Presentationgiven at the April 2012 Federal Utility Partnership Working Group (FUPWG) meetingabout the Federal Energy Management Program's (FEMP's) High-Tech Building Utility Energy Service Contract (UESC) Partnership led by the Lawrence Berkeley National Laboratory (LBNL).

156

High-Level Waste Requirements  

Directives, Delegations, and Requirements

The guide provides the criteria for determining which DOE radioactive wastes are to be managed as high-level waste in accordance with DOE M 435.1-1.

1999-07-09T23:59:59.000Z

157

Philosophy 26 High Temperature Superconductivity  

E-Print Network (OSTI)

is the ratio of voltage to current. The resistance of a material tells us how a low resistance, and they are therefore good conductors; other materials, likePhilosophy 26 High Temperature Superconductivity By Ohm's Law, resistance

Callender, Craig

158

High-frequency discharges III  

Science Journals Connector (OSTI)

We start with a comparison of advantages and disadvantages of capacitively coupled discharges, by which it becomes obvious why and how the semiconductor industry has triggered the demand for high-density plasm...

Prof.Dr. Gerhard Franz

2009-01-01T23:59:59.000Z

159

Research in High Energy Physics  

SciTech Connect

This final report details the work done from January 2010 until April 2013 in the area of experimental and theoretical high energy particle physics and cosmology at the University of California, Davis.

Conway, John S.

2013-08-09T23:59:59.000Z

160

July 24, 2009, Visiting Speakers Program - Regulation and High Reliability Organizations by Dr. Jerry Ellig  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and High Reliability and High Reliability Organizations Jerry Ellig Senior Research Fellow Prepared for the U.S. Department of Energy Office of Health, Safety, and Security Visiting Speakers Program National Academy of Public Administration July 24, 2009 High Reliability Organizations � "Avoid catastrophes in high-risk, complex operating environments ... consistently deliver year-in/year-out high value and high performance regardless of their operating environment." � Key principle: Reality isn't optional. Some examples � Airline and airport security � Electricity � Telecommunications � Finance and banking � Direct wine shipment (OK, maybe not an HRO, but it's a fun and illustrative story) Four suggestions 1. Base decisions on evidence of outcomes 2.

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

High resolution, high rate x-ray spectrometer  

DOE Patents (OSTI)

It is an object of the invention to provide a pulse processing system for use with detected signals of a wide dynamic range which is capable of very high counting rates, with high throughput, with excellent energy resolution and a high signal-to-noise ratio. It is a further object to provide a pulse processing system wherein the fast channel resolving time is quite short and substantially independent of the energy of the detected signals. Another object is to provide a pulse processing system having a pile-up rejector circuit which will allow the maximum number of non-interfering pulses to be passed to the output. It is also an object of the invention to provide new methods for generating substantially symmetrically triangular pulses for use in both the main and fast channels of a pulse processing system.

Goulding, F.S.; Landis, D.A.

1983-07-14T23:59:59.000Z

162

High modulus carbon fiber/titanium laminates  

E-Print Network (OSTI)

Titanium has been used to meet ever-stricter standards for high-temperature performance, creep resistance, low weight and high strength. Having low density, a high melting point, and high tensile strength, it seems like ...

Tsang, Lina

2006-01-01T23:59:59.000Z

163

High pressure synthesis gas conversion. Task 3: High pressure profiles  

SciTech Connect

The purpose of this research project was to build and test a high pressure fermentation system for the production of ethanol from synthesis gas. The fermenters, pumps, controls, and analytical system were procured or fabricated and assembled in our laboratory. This system was then used to determine the effects of high pressure on growth and ethanol production by C. 1jungdahlii. The limits of cell concentration and mass transport relationships were found in CSTR and immobilized cell reactors (ICR). The minimum retention times and reactor volumes were found for ethanol production in these reactors.

Not Available

1993-05-01T23:59:59.000Z

164

High-brightness, high-current ion sources  

SciTech Connect

Several existing high-current dc ion sources are presented that yield positive ions and are based on gas discharges. Their common features are then outlined: extraction systems, required plasma qualities, and the production of ions from solid materials. Finally, from well-established laws, scaling rules for high-brightness ion beams are derived taking one specific case to determine the numerical constants. These rules predict that the current values of transportable beams scale proportionally to the 3/2 power of the extraction voltage, whereas the brightness strongly decreases with rising voltage.

Keller, R.

1985-01-01T23:59:59.000Z

165

Materials Characterization Capabilities at the High Temperature...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Characterization Capabilities at the High Temperature Materials Laboratory: Focus on Carbon Fiber and Composites Materials Characterization Capabilities at the High...

166

High frequency and high dynamic range continuous time filters  

E-Print Network (OSTI)

subscriber line (ADSL), very high bit rate DSL (VDSL) and power line communications (PLC). However, a major challenge is the design of the analog frontend; for these systems a large dynamic range is required due to the significant peak to average ratio...

Lewinski Komincz, Artur Juliusz

2007-09-17T23:59:59.000Z

167

PACIFIC HIGHLY MIGR ATORY PEL AGIC FISHERIES pacific highly migratory  

E-Print Network (OSTI)

the Pacific Ocean, from the tropics to temperate latitudes. Many of these fishes routinely travel great highly migratory species throughout the Pacific Ocean. Some of the fleets are capable of operating across the Pacific as well as in other oceans during a single fishing season. These fleets use larger purse

168

High Pressure Hydrogen Tank Manufacturing  

NLE Websites -- All DOE Office Websites (Extended Search)

Workshop Workshop High Pressure Hydrogen Tank Manufacturing Mark Leavitt Quantum Fuel Systems Technologies Worldwide, Inc. August 11, 2011 This presentation does not contain any proprietary, confidential, or otherwise restricted information History of Innovations... Announced breakthrough in all-composite lightweight, high capacity, low-cost fuel storage technologies. * Developed a series of robust, OEM compatible electronic control products. Developed H 2 storage system for SunLine Tran-sit Hythane® bus. Awarded patent for integrated module including in-tank regulator * Developed high efficiency H 2 fuel storage systems for DOE Future Truck programs Developed H 2 storage and metering system for Toyota's FCEV platform. First to certify 10,000 psi systems in Japan

169

Detonation probabilities of high explosives  

SciTech Connect

The probability of a high explosive violent reaction (HEVR) following various events is an extremely important aspect of estimating accident-sequence frequency for nuclear weapons dismantlement. In this paper, we describe the development of response curves for insults to PBX 9404, a conventional high-performance explosive used in US weapons. The insults during dismantlement include drops of high explosive (HE), strikes of tools and components on HE, and abrasion of the explosive. In the case of drops, we combine available test data on HEVRs and the results of flooring certification tests to estimate the HEVR probability. For other insults, it was necessary to use expert opinion. We describe the expert solicitation process and the methods used to consolidate the responses. The HEVR probabilities obtained from both approaches are compared.

Eisenhawer, S.W.; Bott, T.F.; Bement, T.R.

1995-07-01T23:59:59.000Z

170

High-let radiation carcinogenesis  

SciTech Connect

Recent results for neutron radiation-induced tumors are presented to illustrate the complexities of the dose-response curves for high-LET radiation. It is suggested that in order to derive an appropriate model for dose-response curves for the induction of tumors by high-LET radiation it is necessary to take into account dose distribution, cell killing and the susceptibility of the tissue under study. Preliminary results for the induction of Harderian gland tumors in mice exposed to various heavy ion beams are presented. The results suggest that the effectiveness of the heavy ion beams increases with increasing LET. The slopes of the dose-response curves for the different high-LET radiations decrease between 20 and 40 rads and therefore comparisons of the relative effectiveness should be made from data obtained at doses below about 20 to 30 rads.

Fry, R.J.M.; Powers-Risius, P.; Alpen, E.L.; Ainsworth, E.J.; Ullrich, R.L.

1982-01-01T23:59:59.000Z

171

Electrokinetic high pressure hydraulic system  

DOE Patents (OSTI)

An electrokinetic high pressure hydraulic pump for manipulating fluids in capillary-based systems. The pump uses electro-osmotic flow to provide a high pressure hydraulic system, having no moving mechanical parts, for pumping and/or compressing fluids, for providing valve means and means for opening and closing valves, for controlling fluid flow rate, and manipulating fluid flow generally and in capillary-based systems (Microsystems), in particular. The compact nature of the inventive high pressure hydraulic pump provides the ability to construct a micro-scale or capillary-based HPLC system that fulfills the desire for small sample quantity, low solvent consumption, improved efficiency, the ability to run samples in parallel, and field portability. Control of pressure and solvent flow rate is achieved by controlling the voltage applied to an electrokinetic pump.

Paul, Phillip H. (Livermore, CA); Rakestraw, David J. (Fremont, CA); Arnold, Don W. (Livermore, CA); Hencken, Kenneth R. (Pleasanton, CA); Schoeniger, Joseph S. (Oakland, CA); Neyer, David W. (Castro Valley, CA)

2001-01-01T23:59:59.000Z

172

High Field Magnetic Resonance Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

HFMRF Overview HFMRF Overview Section 2-3-1 High Field Magnetic Resonance Facility The High Field Magnetic Resonance Facility (HFMRF) focuses a significant portion of its research on developing a fundamental, molecular-level understanding of biochemical and biological systems and their response to environmental effects. A secondary focus is materials science, including catalysis and chemical mechanisms and processes. Staff and science consultants within this facility offer expertise in the areas of structural biology, solid-state materials characterization, and magnetic resonance imaging (MRI) techniques. Research activities in the HFMRF include: * structure determination of large molecular assemblies such as protein-DNA (normal and damaged DNA) and protein-RNA complexes

173

High Temperature Optical Gas Sensing  

NLE Websites -- All DOE Office Websites (Extended Search)

Optical Gas Sensing Optical Gas Sensing Opportunity Research is active on optical sensors integrated with advanced sensing materials for high temperature embedded gas sensing applications. Patent applications have been filed for two inventions in this area and several other methods are currently under development. These technologies are available for licensing and/or further collaborative research from the U.S. Department of Energy's National Energy Technology Laboratory (NETL). Organizations or individuals with capabilities in optical sensor packaging for harsh environment and high temperature applications are encouraged to contact NETL to explore potential collaborative opportunities. Overview Contact NETL Technology Transfer Group techtransfer@netl.doe.gov

174

High temperature superconductor current leads  

DOE Patents (OSTI)

An electrical lead is disclosed having one end for connection to an apparatus in a cryogenic environment and the other end for connection to an apparatus outside the cryogenic environment. The electrical lead includes a high temperature superconductor wire and an electrically conductive material distributed therein, where the conductive material is present at the one end of the lead at a concentration in the range of from 0 to about 3% by volume, and at the other end of the lead at a concentration of less than about 20% by volume. Various embodiments are shown for groups of high temperature superconductor wires and sheaths. 9 figs.

Hull, J.R.; Poeppel, R.B.

1995-06-20T23:59:59.000Z

175

Modeling high-genus surfaces  

E-Print Network (OSTI)

, with the large number of holes in the casing for heat dissipation. Figure 4 shows some examples of such objects. 5 Fig. 4. Examples of man-made high-genus objects. I.4. High-genus objects from mathematics In the last two decades, fractal geometry has emerged... as one of the major mathemati- cal approaches for designing unusual 3D shapes. Examples of such shapes introduced by fractal geometry include the Sierpinski gasket, the Menger sponge, the Mandelbrot set and Julia sets [27]. Fractal geometry shapes...

Srinivasan, Vinod

2004-09-30T23:59:59.000Z

176

Processes yielding high superconducting temperatures  

SciTech Connect

It is pointed out that any microscopic description of the new high-T/sub c/ superconductors should take into account a number of important points concerning strong couplings, whatever their nature: absence of the MacMillan limit, absence of a Migdal theorem, and importance of the Brovman-Kagan type of vertices with different singularities depending on the dimensionality. As a consequence, the applicability of standard techniques such as the Eliashberg theory in particular, may be questioned in high-T/sub c/ superconductors.

Beal-Monod, M.T.

1987-12-01T23:59:59.000Z

177

ABBGroup-1-High voltage lab  

E-Print Network (OSTI)

;©ABBGroup-3- 3-Sep-07 Where does one use circuit breakers? High voltage (HV) circuit breakers are keyA DISTRIBUTION MEDIUM AND LOW VOLTAGE HV circuit breakers #12;©ABBGroup-4- 3-Sep-07 When a breaker fails to interrupt the current... Fault arc at a disconnector Fault arc in a substation #12;©ABBGroup-5- 3-Sep-07

Basse, Nils Plesner

178

Removing High Explosives from Groundwater  

Energy.gov (U.S. Department of Energy (DOE))

LOS ALAMOS, N.M. In an initiative supported by EM, Los Alamos National Laboratorys Corrective Actions Program is addressing high explosive contamination in surface water and groundwater at a location this summer in the forests surrounding the laboratory.

179

High precision redundant robotic manipulator  

DOE Patents (OSTI)

A high precision redundant robotic manipulator for overcoming contents imposed by obstacles or imposed by a highly congested work space. One embodiment of the manipulator has four degrees of freedom and another embodiment has seven degreed of freedom. Each of the embodiments utilize a first selective compliant assembly robot arm (SCARA) configuration to provide high stiffness in the vertical plane, a second SCARA configuration to provide high stiffness in the horizontal plane. The seven degree of freedom embodiment also utilizes kinematic redundancy to provide the capability of avoiding obstacles that lie between the base of the manipulator and the end effector or link of the manipulator. These additional three degrees of freedom are added at the wrist link of the manipulator to provide pitch, yaw and roll. The seven degrees of freedom embodiment uses one revolute point per degree of freedom. For each of the revolute joints, a harmonic gear coupled to an electric motor is introduced, and together with properly designed based servo controllers provide an end point repeatability of less than 10 microns.

Young, Kar-Keung David (Mountain View, CA)

1998-01-01T23:59:59.000Z

180

High precision redundant robotic manipulator  

DOE Patents (OSTI)

A high precision redundant robotic manipulator for overcoming contents imposed by obstacles or imposed by a highly congested work space is disclosed. One embodiment of the manipulator has four degrees of freedom and another embodiment has seven degrees of freedom. Each of the embodiments utilize a first selective compliant assembly robot arm (SCARA) configuration to provide high stiffness in the vertical plane, a second SCARA configuration to provide high stiffness in the horizontal plane. The seven degree of freedom embodiment also utilizes kinematic redundancy to provide the capability of avoiding obstacles that lie between the base of the manipulator and the end effector or link of the manipulator. These additional three degrees of freedom are added at the wrist link of the manipulator to provide pitch, yaw and roll. The seven degrees of freedom embodiment uses one revolute point per degree of freedom. For each of the revolute joints, a harmonic gear coupled to an electric motor is introduced, and together with properly designed based servo controllers provide an end point repeatability of less than 10 microns. 3 figs.

Young, K.K.D.

1998-09-22T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

High Performance Outdoor Lighting Accelerator  

Energy.gov (U.S. Department of Energy (DOE))

Hosted by the U.S. Department of Energy (DOE)s Weatherization and Intergovernmental Programs Office (WIPO), this webinar covered the expansion of the Better Buildings platform to include the newest initiative for the public sector: the High Performance Outdoor Lighting Accelerator (HPOLA).

182

High temperature turbine engine structure  

DOE Patents (OSTI)

A high temperature turbine engine includes a rotor portion having axially stacked adjacent ceramic rotor parts. A ceramic/ceramic joint structure transmits torque between the rotor parts while maintaining coaxial alignment and axially spaced mutually parallel relation thereof despite thermal and centrifugal cycling.

Boyd, Gary L. (Tempe, AZ)

1991-01-01T23:59:59.000Z

183

Joyce Eveland Oskaloosa High School  

E-Print Network (OSTI)

Cooker As we are beginning conic sections I assign the students a project to build a solar cooker by researching solar cookers and forming teams of three to four students. During this time they are instructedJoyce Eveland Oskaloosa High School evelandj@oskaloosa.k12.ia.us Parabolic Solar

184

Architecture: Watch on High Buildings  

Science Journals Connector (OSTI)

... England and Wales, would like to see a firm policy for the control of high buildings in London. The commissioners, who include Mr John Betjeman, Sir Hugh Casson, Lord ... that there are increasing pressures on the local authorities in London for planning consent for buildings above what used to be considered normal height limits, and there has been a ...

1969-04-12T23:59:59.000Z

185

Synthesis of Highly Efficient Flame Retardant High-Density Polyethylene Nanocomposites with Inorgano-Layered Double  

E-Print Network (OSTI)

Synthesis of Highly Efficient Flame Retardant High-Density Polyethylene Nanocomposites, Harbin 150080, P. R. China ABSTRACT: High-density polyethylene (HDPE) polymer nanocomposites containing. INTRODUCTION High density polyethylene (HDPE) has good electrical proper- ties, high stiffness, and tensile

Guo, John Zhanhu

186

Develop high energy high power Li-ion battery cathode materials : a first principles computational study  

E-Print Network (OSTI)

develop the high energy high power cathode materials for LIBNew Cathode Material for Batteries of High- Energy Density.High Energy High Power Li-ion Battery Cathode Materials A

Xu, Bo; Xu, Bo

2012-01-01T23:59:59.000Z

187

NOVEL REFRACTORY MATERIALS FOR HIGH ALKALI, HIGH TEMPERATURE ENVIRONMENTS  

SciTech Connect

Refractory materials can be limited in their application by many factors including chemical reactions between the service environment and the refractory material, mechanical degradation of the refractory material by the service environment, temperature limitations on the use of a particular refractory material, and the inability to install or repair the refractory material in a cost effective manner or while the vessel was in service. The objective of this project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al 2O3 spinel or other similar magnesia/alumina containing unshaped refractory composition (castables, gunnables, shotcretes, etc) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, high-alkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries.

Hemrick, James Gordon [ORNL

2011-09-01T23:59:59.000Z

188

High-sensitivity, high-speed continuous imaging system  

DOE Patents (OSTI)

A continuous imaging system for recording low levels of light typically extending over small distances with high-frame rates and with a large number of frames is described. Photodiode pixels disposed in an array having a chosen geometry, each pixel having a dedicated amplifier, analog-to-digital convertor, and memory, provide parallel operation of the system. When combined with a plurality of scintillators responsive to a selected source of radiation, in a scintillator array, the light from each scintillator being directed to a single corresponding photodiode in close proximity or lens-coupled thereto, embodiments of the present imaging system may provide images of x-ray, gamma ray, proton, and neutron sources with high efficiency.

Watson, Scott A; Bender, III, Howard A

2014-11-18T23:59:59.000Z

189

High energy resolution, high angular acceptance crystal monochromator  

DOE Patents (OSTI)

A 4-bounce dispersive crystal monochromator reduces the bandpass of synchrotron radiation to a 10-50 meV range without sacrificing angular acceptance. The monochromator includes the combination of an asymmetrical channel-cut single crystal of lower order reflection and a symmetrical channel-cut single crystal of higher order reflection in a nested geometric configuration. In the disclosed embodiment, a highly asymmetrically cut (.alpha.=20) outer silicon crystal (4 2 2) with low order reflection is combined with a symmetrically cut inner silicon crystal (10 6 4) with high order reflection to condition a hard x-ray component (5-30 keV) of synchrotron radiation down to the .mu.eV-neV level. Each of the crystals is coupled to the combination of a positioning inchworm and angle encoder via a respective rotation stage for accurate relative positioning of the crystals and precise energy tuning of the monochromator.

Alp, Ercan E. (Bolingbrook, IL); Mooney, Timothy M. (Westmont, IL); Toellner, Thomas (Green Bay, WI)

1996-06-04T23:59:59.000Z

190

High performance internal reforming unit for high temperature fuel cells  

DOE Patents (OSTI)

A fuel reformer having an enclosure with first and second opposing surfaces, a sidewall connecting the first and second opposing surfaces and an inlet port and an outlet port in the sidewall. A plate assembly supporting a catalyst and baffles are also disposed in the enclosure. A main baffle extends into the enclosure from a point of the sidewall between the inlet and outlet ports. The main baffle cooperates with the enclosure and the plate assembly to establish a path for the flow of fuel gas through the reformer from the inlet port to the outlet port. At least a first directing baffle extends in the enclosure from one of the sidewall and the main baffle and cooperates with the plate assembly and the enclosure to alter the gas flow path. Desired graded catalyst loading pattern has been defined for optimized thermal management for the internal reforming high temperature fuel cells so as to achieve high cell performance.

Ma, Zhiwen (Sandy Hook, CT); Venkataraman, Ramakrishnan (New Milford, CT); Novacco, Lawrence J. (Brookfield, CT)

2008-10-07T23:59:59.000Z

191

Assessment of microelectronics packaging for high temperature, high reliability applications  

SciTech Connect

This report details characterization and development activities in electronic packaging for high temperature applications. This project was conducted through a Department of Energy sponsored Cooperative Research and Development Agreement between Sandia National Laboratories and General Motors. Even though the target application of this collaborative effort is an automotive electronic throttle control system which would be located in the engine compartment, results of this work are directly applicable to Sandia`s national security mission. The component count associated with the throttle control dictates the use of high density packaging not offered by conventional surface mount. An enabling packaging technology was selected and thermal models defined which characterized the thermal and mechanical response of the throttle control module. These models were used to optimize thick film multichip module design, characterize the thermal signatures of the electronic components inside the module, and to determine the temperature field and resulting thermal stresses under conditions that may be encountered during the operational life of the throttle control module. Because the need to use unpackaged devices limits the level of testing that can be performed either at the wafer level or as individual dice, an approach to assure a high level of reliability of the unpackaged components was formulated. Component assembly and interconnect technologies were also evaluated and characterized for high temperature applications. Electrical, mechanical and chemical characterizations of enabling die and component attach technologies were performed. Additionally, studies were conducted to assess the performance and reliability of gold and aluminum wire bonding to thick film conductor inks. Kinetic models were developed and validated to estimate wire bond reliability.

Uribe, F.

1997-04-01T23:59:59.000Z

192

INDIANA UNIVERSITY William Sherman Senior Technology Advisor...  

NLE Websites -- All DOE Office Websites (Extended Search)

INDIANA UNIVERSITY William Sherman Senior Technology Advisor, Indiana University William Sherman is a senior technical advisor at Indiana University. He is the scientific...

193

High-Throughput Screening Techniques  

NLE Websites -- All DOE Office Websites (Extended Search)

Throughput Throughput Screening Techniques for Biomass Conversion Stephen R. Decker & Roman Brunecky & Melvin P. Tucker & Michael E. Himmel & Michael J. Selig Published online: 14 October 2009 # US Government 2009 Abstract High-throughput (HTP) screening of biomass or biomass-degrading enzymes, regardless of the desired outcome, is fraught with obstacles and challenges not typically faced in more traditional biotechnology. The enzyme systems are complex and synergistic and the substrate is highly heterogeneous, insoluble, and difficult to dispense. Digestions are often carried out for days at temperatures of 50°C or higher, leading to significant challenges regarding evaporation control in small well volumes. Furthermore, it is often desirable to condition or "pretreat" the biomass at extreme temperatures and/or pH to enhance enzyme digestibility.

194

Radiometry High Spectral Resolution Fourier  

NLE Websites -- All DOE Office Websites (Extended Search)

High Spectral Resolution Fourier High Spectral Resolution Fourier Transform Infrared Instruments for the Atmospheric Radiation Measurement Program H. E. Revercomb, W. L. Smith, R. O. Knuteson, F. A. Best, R. G. Dedecker, T. P. Dirkx, R. A. Herbsleb, and J. F. Short University of Wisconsin Madison, Wisconsin H. B. Howell National Oceanic and Atmospheric Administration Systems Design and Applications Branch Madison, Wisconsin D. Murcray and F. Murcray University of Denver Denver, Colorado Accurate and spectrally detailed observations of the thermal emission from radiatively important atmospheric gases, aerosols, and clouds have been identified as crucial for realizing the overall objectives of the Atmospheric Radiation Measurement (ARM) Program to improve the treatment of radiation and clouds in climate models. The observed

195

High Capacity Immobilized Amine Sorbents  

NLE Websites -- All DOE Office Websites (Extended Search)

Capacity Immobilized Amine Sorbents Capacity Immobilized Amine Sorbents Opportunity The Department of Energy's National Energy Technology Laboratory is seeking licensing partners interested in implementing United States Patent Number 7,288,136 entitled "High Capacity Immobilized Amine Sorbents." Disclosed in this patent is the invention of a method that facilitates the production of low-cost carbon dioxide (CO 2 ) sorbents for use in large-scale gas-solid processes. This method treats an amine to increase the number of secondary amine groups and impregnates the amine in a porous solid support. As a result of this improvement, the method increases CO 2 capture capacity and decreases the cost of using an amine-enriched solid sorbent in CO 2 capture systems. Overview The U.S. Department of Energy has placed a high priority on the separation

196

High Mesa | Open Energy Information  

Open Energy Info (EERE)

Mesa Mesa Jump to: navigation, search Name High Mesa Facility High Mesa Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Exelon Wind Developer Exelon Wind Energy Purchaser Idaho Power Location Bliss ID Coordinates 42.88797667°, -115.0169849° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.88797667,"lon":-115.0169849,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

197

High-contrast imaging testbed  

SciTech Connect

Several high-contrast imaging systems are currently under construction to enable the detection of extra-solar planets. In order for these systems to achieve their objectives, however, there is considerable developmental work and testing which must take place. Given the need to perform these tests, a spatially-filtered Shack-Hartmann adaptive optics system has been assembled to evaluate new algorithms and hardware configurations which will be implemented in these future high-contrast imaging systems. In this article, construction and phase measurements of a membrane 'woofer' mirror are presented. In addition, results from closed-loop operation of the assembled testbed with static phase plates are presented. The testbed is currently being upgraded to enable operation at speeds approaching 500 hz and to enable studies of the interactions between the woofer and tweeter deformable mirrors.

Baker, K; Silva, D; Poyneer, L; Macintosh, B; Bauman, B; Palmer, D; Remington, T; Delgadillo-Lariz, M

2008-01-23T23:59:59.000Z

198

High power gas laser amplifier  

DOE Patents (OSTI)

A high power output CO.sub.2 gas laser amplifier having a number of sections, each comprising a plurality of annular pumping chambers spaced around the circumference of a vacuum chamber containing a cold cathode, gridded electron gun. The electron beam from the electron gun ionizes the gas lasing medium in the sections. An input laser beam is split into a plurality of annular beams, each passing through the sections comprising one pumping chamber.

Leland, Wallace T. (Los Alamos, NM); Stratton, Thomas F. (Los Alamos, NM)

1981-01-01T23:59:59.000Z

199

Cosmology for high energy physicists  

SciTech Connect

The standard big bang model of cosmology is presented. Although not perfect, its many successes make it a good starting point for most discussions of cosmology. Places are indicated where well understood laboratory physics is incorporated into the big bang, leading to successful predictions. Much less established aspects of high energy physics and some of the new ideas they have introduced into the field of cosmology are discussed, such as string theory, inflation and monopoles. 49 refs., 5 figs.

Albrecht, A.

1987-11-01T23:59:59.000Z

200

High temperature turbine engine structure  

DOE Patents (OSTI)

A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

Carruthers, William D. (Mesa, AZ); Boyd, Gary L. (Tempe, AZ)

1994-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

High temperature turbine engine structure  

DOE Patents (OSTI)

A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

Carruthers, William D. (Mesa, AZ); Boyd, Gary L. (Tempe, AZ)

1993-01-01T23:59:59.000Z

202

High temperature turbine engine structure  

DOE Patents (OSTI)

A high temperature ceramic/metallic turbine engine includes a metallic housing which journals a rotor member of the turbine engine. A ceramic disk-like shroud portion of the engine is supported on the metallic housing portion and maintains a close running clearance with the rotor member. A ceramic spacer assembly maintains the close running clearance of the shroud portion and rotor member despite differential thermal movements between the shroud portion and metallic housing portion.

Carruthers, William D. (Mesa, AZ); Boyd, Gary L. (Tempe, AZ)

1992-01-01T23:59:59.000Z

203

High-performance, high-volume fly ash concrete  

SciTech Connect

This booklet offers the construction professional an in-depth description of the use of high-volume fly ash in concrete. Emphasis is placed on the need for increased utilization of coal-fired power plant byproducts in lieu of Portland cement materials to eliminate increased CO{sub 2} emissions during the production of cement. Also addressed is the dramatic increase in concrete performance with the use of 50+ percent fly ash volume. The booklet contains numerous color and black and white photos, charts of test results, mixtures and comparisons, and several HVFA case studies.

NONE

2008-01-15T23:59:59.000Z

204

Army High Performance Computing Research Center  

E-Print Network (OSTI)

Army High Performance Computing Research Center Applying advanced computational science research challenges http://me.stanford.edu/research/centers/ahpcrc #12;Army High Performance Computing challenges http://me.stanford.edu/research/centers/ahpcrc #12;Army High Performance Computing Research

Prinz, Friedrich B.

205

High Temperature Mechanical Properties as Design Parameters  

Science Journals Connector (OSTI)

...corrosion resistance or high proof strength...development of more efficient power plant, process...Figure 2 shows a high temperature bolt...S.O.) of a Boiler Code (I968...power plant for high temperature pipework, boiler headers, valve...

1976-01-01T23:59:59.000Z

206

PRACTICAL NEUTRON DOSIMETRY AT HIGH ENERGIES  

E-Print Network (OSTI)

of High-Energy Accelerators, New York, April, 1957. USAECShielding of High-Energy Accelerators, New York, April 1957.Shielding of High-Energy Accelerators, New York, April 1957.

McCaslin, J.B.

2010-01-01T23:59:59.000Z

207

Proposal for a High Energy Nuclear Database  

E-Print Network (OSTI)

Proposal for a High Energy Nuclear Database David A. Brown 1it requires the high-energy nuclear physics com- munitys ?compilations of high-energy nuclear data for applications

Brown, David A.; Vogt, Ramona

2005-01-01T23:59:59.000Z

208

Advanced High-Temperature, High-Pressure Transport Reactor Gasification  

SciTech Connect

The U.S. Department of Energy (DOE) National Energy Technology Laboratory Office of Coal and Environmental Systems has as its mission to develop advanced gasification-based technologies for affordable, efficient, zero-emission power generation. These advanced power systems, which are expected to produce near-zero pollutants, are an integral part of DOE's Vision 21 Program. DOE has also been developing advanced gasification systems that lower the capital and operating costs of producing syngas for chemical production. A transport reactor has shown potential to be a low-cost syngas producer compared to other gasification systems since its high-throughput-per-unit cross-sectional area reduces capital costs. This work directly supports the Power Systems Development Facility utilizing the KBR transport reactor located at the Southern Company Services Wilsonville, Alabama, site. Over 2800 hours of operation on 11 different coals ranging from bituminous to lignite along with a petroleum coke has been completed to date in the pilot-scale transport reactor development unit (TRDU) at the Energy & Environmental Research Center (EERC). The EERC has established an extensive database on the operation of these various fuels in both air-blown and oxygen-blown modes utilizing a pilot-scale transport reactor gasifier. This database has been useful in determining the effectiveness of design changes on an advanced transport reactor gasifier and for determining the performance of various feedstocks in a transport reactor. The effects of different fuel types on both gasifier performance and the operation of the hot-gas filter system have been determined. It has been demonstrated that corrected fuel gas heating values ranging from 90 to 130 Btu/scf have been achieved in air-blown mode, while heating values up to 230 Btu/scf on a dry basis have been achieved in oxygen-blown mode. Carbon conversions up to 95% have also been obtained and are highly dependent on the oxygen-coal ratio. Higher-reactivity (low-rank) coals appear to perform better in a transport reactor than the less reactive bituminous coals. Factors that affect TRDU product gas quality appear to be coal type, temperature, and air/coal ratios. Testing with a higher-ash, high-moisture, low-rank coal from the Red Hills Mine of the Mississippi Lignite Mining Company has recently been completed. Testing with the lignite coal generated a fuel gas with acceptable heating value and a high carbon conversion, although some drying of the high-moisture lignite was required before coal-feeding problems were resolved. No ash deposition or bed material agglomeration issues were encountered with this fuel. In order to better understand the coal devolatilization and cracking chemistry occurring in the riser of the transport reactor, gas and solid sampling directly from the riser and the filter outlet has been accomplished. This was done using a baseline Powder River Basin subbituminous coal from the Peabody Energy North Antelope Rochelle Mine near Gillette, Wyoming.

Michael Swanson; Daniel Laudal

2008-03-31T23:59:59.000Z

209

High Performance Sustainable Building - DOE Directives, Delegations...  

NLE Websites -- All DOE Office Websites (Extended Search)

6A, High Performance Sustainable Building by Adam Pugh Functional areas: Program Management, Project Management This Guide provides approaches for implementing the High Performance...

210

Acid Doped Membranes for High Temperature PEMFC  

Energy.gov (U.S. Department of Energy (DOE))

Presentation on Acid Doped Membranes for High Temperature PEMFC to the High Temperature Membrane Working Group, May 25, 2004 in Philadelphia, PA.

211

High performance computing Igal G. Rasin  

E-Print Network (OSTI)

High performance computing Igal G. Rasin Department of Chemical Engineering, Technion Israel with different parallelization techniques and tools used in high performance computing (HPC). The tutorial

Adler, Joan

212

Building America Webinar: High Performance Enclosure Strategies...  

Energy Savers (EERE)

II, New Construction - August 13, 2014 - Next Gen Advanced Framing for High Performance Homes Integrated System Solutions Building America Webinar: High Performance Enclosure...

213

Continuous Processing of High Thermal Conductivity Polyethylene...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Processing of High Thermal Conductivity Polyethylene Fibers and Sheets Continuous Processing of High Thermal Conductivity Polyethylene Fibers and Sheets Massachusetts Institute of...

214

Building America Webinar: High Performance Space Conditioning...  

Energy Savers (EERE)

Kohta Ueno, Building Science Corporation. Kohta will discuss BSC's research on ductless heat pumps versus mini-splits being used in high performance (high R value enclosurelow...

215

Experiment Hazard Class 3 - High Temperatures  

NLE Websites -- All DOE Office Websites (Extended Search)

Operation * APS Base Low Temperatures * Cryogenic Systems High Temperatures * Electric Furnace * Optical Furnace * Other High Temperature Lasers * Laser, Class 2 * Laser,...

216

HIGH INTEGRITY MAGNESIUM AUTOMOTIVE COMPONENTS (HIMAC) | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

HIGH INTEGRITY MAGNESIUM AUTOMOTIVE COMPONENTS (HIMAC) HIGH INTEGRITY MAGNESIUM AUTOMOTIVE COMPONENTS (HIMAC) 2009 DOE Hydrogen Program and Vehicle Technologies Program Annual...

217

High Voltage Electrolyte for Lithium Batteries  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

battery using high voltage high energy cathode materials to enable large-scale, cost competitive production of the next generation of electric-drive vehicles. To...

218

High Energy Density Ultracapacitors | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation es038smith2011p.pdf More Documents & Publications High Energy Density Ultracapacitors High...

219

INSENSITIVE HIGH-NITROGEN COMPOUNDS  

SciTech Connect

The conventional approach to developing energetic molecules is to chemically place one or more nitro groups onto a carbon skeleton, which is why the term ''nitration'' is synonymous to explosives preparation. The nitro group carries the oxygen that reacts with the skeletal carbon and hydrogen fuels, which in turn produces the heat and gaseous reaction products necessary for driving an explosive shock. These nitro-containing energetic molecules typically have heats of formation near zero and therefore most of the released energy is derived from the combustion process. Our investigation of the tetrazine, furazan and tetrazole ring systems has offered a different approach to explosives development, where a significant amount of the chemical potential energy is derived from their large positive heats of formation. Because these compounds often contain a large percentage of nitrogen atoms, they are usually regarded as high-nitrogen fuels or explosives. A general artifact of these high-nitrogen compounds is that they are less sensitive to initiation (e.g. by impact) when compared to traditional nitro-containing explosives of similar performances. Using the precursor, 3,6-bis-(3,5-dimethylpyrazol-1-yl)-s-tetrazine, several useful energetic compounds based on the s-tetrazine system have been synthesized and studied. Some of the first compounds are 3,6-diamino-s-tetrazine-1,4-dioxide (LAX-112) and 3,6-dihydrazino-s-tetrazine (DHT). LAX-112 was once extensively studied as an insensitive explosive by Los Alamos; DHT is an example of a high-nitrogen explosive that relies entirely on its heat of formation for sustaining a detonation. Recent synthesis efforts have yielded an azo-s-tetrazine, 3,3'-azobis(6-amino-s-tetrazine) or DAAT, which has a very high positive heat of formation. The compounds, 4,4'-diamino-3,3'-azoxyfurazan (DAAF) and 4,4'-diamino-3,3'-azofurazan (DAAzF), may have important future roles in insensitive explosive applications. Neither DAAF nor DAAzF can be initiated by laboratory impact drop tests, yet both have in some aspects better explosive performances than 1,3,5-triamino-2,4,6-trinitrobenzene TATB--the standard of insensitive high explosives. The thermal stability of DAAzF is equal to that of hexanitrostilbene (HNS), yet it too is a better explosive performer. The recently discovered tetrazol derivative, 3,6-bis-(1H-1,2,3,4-tetrazol-5-ylamino)-s-tetrazine (BTATz) was measured to have exceptional positive heats of formation and to be insensitive to explosive initiation. Because of its high burn rate with low sensitivity to pressure, this material is of great interest to the propellant community.

D. CHAVEZ; ET AL

2001-03-01T23:59:59.000Z

220

High flux solar energy transformation  

DOE Patents (OSTI)

Disclosed are multi-stage systems for high flux transformation of solar energy allowing for uniform solar intensification by a factor of 60,000 suns or more. Preferred systems employ a focusing mirror as a primary concentrative device and a non-imaging concentrator as a secondary concentrative device with concentrative capacities of primary and secondary stages selected to provide for net solar flux intensification of greater than 2000 over 95 percent of the concentration area. Systems of the invention are readily applied as energy sources for laser pumping and in other photothermal energy utilization processes.

Winston, Roland (Chicago, IL); Gleckman, Philip L. (Chicago, IL); O'Gallagher, Joseph J. (Flossmoor, IL)

1991-04-09T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

High voltage RF feedthrough bushing  

DOE Patents (OSTI)

Described is a multi-element, high voltage radio frequency bushing for trmitting RF energy to an antenna located in a vacuum container. The bushing includes a center conductor of complex geometrical shape, an outer coaxial shield conductor, and a thin-walled hollow truncated cone insulator disposed between central and outer conductors. The shape of the center conductor, which includes a reverse curvature portion formed of a radially inwardly directed shoulder and a convex portion, controls the uniformity of the axial surface gradient on the insulator cone. The outer shield has a first substantially cylindrical portion and a second radially inwardly extending truncated cone portion.

Grotz, Glenn F. (Huntington Station, NY)

1984-01-01T23:59:59.000Z

222

High-energy Cosmic Rays  

E-Print Network (OSTI)

After a brief review of galactic cosmic rays in the GeV to TeV energy range, we describe some current problems of interest for particles of very high energy. Particularly interesting are two features of the spectrum, the `knee' above $10^{15}$ eV and the `ankle' above $10^{18}$ eV. An important question is whether the highest energy particles are of extra-galactic origin and, if so, at what energy the transition occurs. A theme common to all energy ranges is use of nuclear abundances as a tool for understanding the origin of the cosmic radiation.

Thomas K. Gaisser; Todor Stanev

2005-10-11T23:59:59.000Z

223

Highly asymmetric Laue focusing monochromator  

SciTech Connect

By using two highly asymmetric Laue crystals in a dispersive arrangement with a circular profile (Oe 8 mm) we have created a sagittaly focusing Laue system for the first time. The crystallographic planes (111) of the two Si crystals formed an angle of 7.95 deg. with the entrance surface. The crystals dimensions were 40 mmx20 mm and the diffracting surface was a 0.5 mm thick neck between the two circular profiles. The 15.35 keV diffracted beam formed an angle of 0.55 deg. with the exit surface. The calculated focusing distance of the Laue-Laue focusing system was 14 m.

Oberta, P. [Institute of Physics, Academy of Sciences of the Czech Republic v.v.i., Na Slovance 2, Praha 8 (Czech Republic); Swiss Light Source, Paul Scherrer Institut, Villigen (Switzerland); Mikulik, P. [Department of Condensed Matter Physics, Faculty of Science, Masaryk University, Kotlarska 2, Brno (Czech Republic); Hrdy, J.; Kittler, M. [Institute of Physics, Academy of Sciences of the Czech Republic v.v.i., Na Slovance 2, Praha 8 (Czech Republic)

2010-06-23T23:59:59.000Z

224

High- and low-temperature-stable thermite composition for producing high-pressure, high-velocity gases  

DOE Patents (OSTI)

A high- and low-temperature-stable thermite composition for producing high-pressure and high-velocity gases comprises an oxidizable metal, an oxidizing reagent, and a high-temperature-stable gas-producing additive selected from the group consisting of metal carbides and metal nitrides.

Halcomb, Danny L. (Camden, OH); Mohler, Jonathan H. (Spring Valley, OH)

1990-10-16T23:59:59.000Z

225

High energy mode locked fiber oscillators for high contrast, high energy petawatt laser seed sources  

SciTech Connect

In a high-energy petawatt laser beam line the ASE pulse contrast is directly related to the total laser gain. Thus a more energetic input pulse will result in increased pulse contrast at the target. We have developed a mode-locked fiber laser with high quality pulses and energies exceeding 25nJ. We believe this 25nJ result is scalable to higher energies. This oscillator has no intra-cavity dispersion compensation, which yields an extremely simple, and elegant laser configuration. We will discuss the design of this laser, our most recent results and characterization of all the key parameters relevant to it use as a seed laser. Our oscillator is a ring cavity mode-locked fiber laser [1]. These lasers operate in a self-similar pulse propagation regime characterized by a spectrum that is almost square. This mode was found theoretically [2] to occur only in the positive dispersion regime. Further increasing positive dispersion should lead to increasing pulse energy [2]. We established that the positive dispersion required for high-energy operation was approximately that of 2m of fiber. To this end, we constructed a laser cavity similar to [1], but with no gratings and only 2m of fiber, which we cladding pumped in order to ensure sufficient pump power was available to achieve mode-locked operation. A schematic of the laser is shown in figure 1 below. This laser produced low noise 25nJ pulses with a broad self similar spectrum (figure 2) and pulses that could be de-chirped to <100fs (figure 3). Pulse contrast is important in peta-watt laser systems. A major contributor to pulse contrast is amplified spontaneous emission (ASE), which is proportional to the gain in the laser chain. As the oscillator strength is increased, the required gain to reach 1PW pulses is decreased, reducing ASE and improving pulse contrast. We believe these lasers can be scaled in a stable fashion to pulse energies as high as 100nJ and have in fact seen 60nJ briefly in our lab, which is work still in progress. At this level, even if the pulses are not perfect, post-oscillator pulse cleaning can be used to create a clean high energy pulse for injection into a peta-watt laser beam line.

Dawson, J W; Messerly, M J; An, J; Kim, D; Barty, C J

2006-06-15T23:59:59.000Z

226

High pressure ceramic heat exchanger  

DOE Patents (OSTI)

Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present header assembly when used with recuperators reduces the brittle effect of a portion of the ceramic components. Thus, the present header assembly used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present header assembly is comprised of a first ceramic member, a second ceramic member, a reinforcing member being in spaced relationship to the first ceramic member and the second ceramic member. The header assembly is further comprised of a refractory material disposed in contacting relationship with the first ceramic member, the second ceramic member and the reinforcing member and having a strengthening member wrapped around the refractory material. The present header assembly provides a high strength load bearing header assembly having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures.

Harkins, Bruce D. (San Diego, CA); Ward, Michael E. (Poway, CA)

1999-01-01T23:59:59.000Z

227

High pressure ceramic heat exchanger  

DOE Patents (OSTI)

Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present header assembly when used with recuperators reduces the brittle effect of a portion of the ceramic components. Thus, the present header assembly used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present header assembly is comprised of a first ceramic member, a second ceramic member, a strengthening reinforcing member being in spaced relationship to the first ceramic member and the second ceramic member. The header assembly is further comprised of a refractory material disposed in contacting relationship with the first ceramic member, the second ceramic member and the strengthening reinforcing member. The present header assembly provides a high strength load bearing header assembly having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures.

Harkins, Bruce D. (San Diego, CA); Ward, Michael E. (Poway, CA)

1998-01-01T23:59:59.000Z

228

High pressure ceramic heat exchanger  

DOE Patents (OSTI)

Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present header assembly when used with recuperators reduces the brittle effect of a portion of the ceramic components. Thus, the present header assembly used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present header assembly is comprised of a first ceramic member, a second ceramic member, a strengthening reinforcing member being in spaced relationship to the first ceramic member and the second ceramic member. The header assembly is further comprised of a refractory material disposed in contacting relationship with the first ceramic member, the second ceramic member and the strengthening reinforcing member. The present header assembly provides a high strength load bearing header assembly having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures. 5 figs.

Harkins, B.D.; Ward, M.E.

1998-09-22T23:59:59.000Z

229

High speed imager test station  

DOE Patents (OSTI)

A test station enables the performance of a solid state imager (herein called a focal plane array or FPA) to be determined at high image frame rates. A programmable waveform generator is adapted to generate clock pulses at determinable rates for clock light-induced charges from a FPA. The FPA is mounted on an imager header board for placing the imager in operable proximity to level shifters for receiving the clock pulses and outputting pulses effective to clock charge from the pixels forming the FPA. Each of the clock level shifters is driven by leading and trailing edge portions of the clock pulses to reduce power dissipation in the FPA. Analog circuits receive output charge pulses clocked from the FPA pixels. The analog circuits condition the charge pulses to cancel noise in the pulses and to determine and hold a peak value of the charge for digitizing. A high speed digitizer receives the peak signal value and outputs a digital representation of each one of the charge pulses. A video system then displays an image associated with the digital representation of the output charge pulses clocked from the FPA. In one embodiment, the FPA image is formatted to a standard video format for display on conventional video equipment. 12 figs.

Yates, G.J.; Albright, K.L.; Turko, B.T.

1995-11-14T23:59:59.000Z

230

High speed imager test station  

DOE Patents (OSTI)

A test station enables the performance of a solid state imager (herein called a focal plane array or FPA) to be determined at high image frame rates. A programmable waveform generator is adapted to generate clock pulses at determinable rates for clock light-induced charges from a FPA. The FPA is mounted on an imager header board for placing the imager in operable proximity to level shifters for receiving the clock pulses and outputting pulses effective to clock charge from the pixels forming the FPA. Each of the clock level shifters is driven by leading and trailing edge portions of the clock pulses to reduce power dissipation in the FPA. Analog circuits receive output charge pulses clocked from the FPA pixels. The analog circuits condition the charge pulses to cancel noise in the pulses and to determine and hold a peak value of the charge for digitizing. A high speed digitizer receives the peak signal value and outputs a digital representation of each one of the charge pulses. A video system then displays an image associated with the digital representation of the output charge pulses clocked from the FPA. In one embodiment, the FPA image is formatted to a standard video format for display on conventional video equipment.

Yates, George J. (Santa Fe, NM); Albright, Kevin L. (Los Alamos, NM); Turko, Bojan T. (Moraga, CA)

1995-01-01T23:59:59.000Z

231

Terascale Physics Opportunities at a High Statistics, High Energy Neutrino Scattering Experiment: NuSOnG  

E-Print Network (OSTI)

This article presents the physics case for a new high-energy, ultra-high statistics neutrino scattering

Adams, T.

232

Guide for High-Performance Buildings Available  

SciTech Connect

This article is an overview of the new "Sustainable, High-Performance Operations and Maintenance" guidelines.

Bartlett, Rosemarie

2012-10-01T23:59:59.000Z

233

What is high-dimensional combinatorics?  

E-Print Network (OSTI)

What is high-dimensional combinatorics? Nati Linial Random-Approx, August '08 Nati Linial What What is high-dimensional combinatorics? #12;So, what is the next frontier? Nati Linial What is high other mathematical sciences, theoretical or applied? Nati Linial What is high-dimensional combinatorics

Linial, Nathan "Nati"

234

Advanced High-Temperature, High-Pressure Transport Reactor Gasification  

SciTech Connect

The transport reactor development unit (TRDU) was modified to accommodate oxygen-blown operation in support of a Vision 21-type energy plex that could produce power, chemicals, and fuel. These modifications consisted of changing the loop seal design from a J-leg to an L-valve configuration, thereby increasing the mixing zone length and residence time. In addition, the standpipe, dipleg, and L-valve diameters were increased to reduce slugging caused by bubble formation in the lightly fluidized sections of the solid return legs. A seal pot was added to the bottom of the dipleg so that the level of solids in the standpipe could be operated independently of the dipleg return leg. A separate coal feed nozzle was added that could inject the coal upward into the outlet of the mixing zone, thereby precluding any chance of the fresh coal feed back-mixing into the oxidizing zone of the mixing zone; however, difficulties with this coal feed configuration led to a switch back to the original downward configuration. Instrumentation to measure and control the flow of oxygen and steam to the burner and mix zone ports was added to allow the TRDU to be operated under full oxygen-blown conditions. In total, ten test campaigns have been conducted under enriched-air or full oxygen-blown conditions. During these tests, 1515 hours of coal feed with 660 hours of air-blown gasification and 720 hours of enriched-air or oxygen-blown coal gasification were completed under this particular contract. During these tests, approximately 366 hours of operation with Wyodak, 123 hours with Navajo sub-bituminous coal, 143 hours with Illinois No. 6, 106 hours with SUFCo, 110 hours with Prater Creek, 48 hours with Calumet, and 134 hours with a Pittsburgh No. 8 bituminous coal were completed. In addition, 331 hours of operation on low-rank coals such as North Dakota lignite, Australian brown coal, and a 90:10 wt% mixture of lignite and wood waste were completed. Also included in these test campaigns was 50 hours of gasification on a petroleum coke from the Hunt Oil Refinery and an additional 73 hours of operation on a high-ash coal from India. Data from these tests indicate that while acceptable fuel gas heating value was achieved with these fuels, the transport gasifier performs better on the lower-rank feedstocks because of their higher char reactivity. Comparable carbon conversions have been achieved at similar oxygen/coal ratios for both air-blown and oxygen-blown operation for each fuel; however, carbon conversion was lower for the less reactive feedstocks. While separation of fines from the feed coals is not needed with this technology, some testing has suggested that feedstocks with higher levels of fines have resulted in reduced carbon conversion, presumably due to the inability of the finer carbon particles to be captured by the cyclones. These data show that these low-rank feedstocks provided similar fuel gas heating values; however, even among the high-reactivity low-rank coals, the carbon conversion did appear to be lower for the fuels (brown coal in particular) that contained a significant amount of fines. The fuel gas under oxygen-blown operation has been higher in hydrogen and carbon dioxide concentration since the higher steam injection rate promotes the water-gas shift reaction to produce more CO{sub 2} and H{sub 2} at the expense of the CO and water vapor. However, the high water and CO{sub 2} partial pressures have also significantly reduced the reaction of (Abstract truncated)

Michael L. Swanson

2005-08-30T23:59:59.000Z

235

Joint Institute for High Temperatures  

National Nuclear Security Administration (NNSA)

Joint Institute for High Temperatures of Russian Academy of Sciences Moscow Institute of Physics and Technology Extended title Extended title Excited state of warm dense matter or Exotic state of warm dense matter or Novel form of warm dense matter or New form of plasma Three sources of generation similarity: solid state density, two temperatures: electron temperature about tens eV, cold ions keep original crystallographic positions, but electron band structure and phonon dispersion are changed, transient but steady (quasi-stationary for a short time) state of non-equilibrium, uniform plasmas (no reference to non-ideality, both strongly and weakly coupled plasmas can be formed) spectral line spectra are emitted by ion cores embedded in plasma environment which influences the spectra strongly,

236

High-Speed Optical Spectroscopy  

E-Print Network (OSTI)

The large surveys and sensitive instruments of modern astronomy are turning ever more examples of variable objects, many of which are extending the parameter space to testing theories of stellar evolution and accretion. Future projects such as the Laser Interferometer Space Antenna (LISA) and the Large Synoptic Survey Telescope (LSST) will only add more challenging candidates to this list. Understanding such objects often requires fast spectroscopy, but the trend for ever larger detectors makes this difficult. In this contribution I outline the science made possible by high-speed spectroscopy, and consider how a combination of the well-known progress in computer technology combined with recent advances in CCD detectors may finally enable it to become a standard tool of astrophysics.

T. R. Marsh

2007-06-28T23:59:59.000Z

237

Steam Oxidation at High Pressure  

SciTech Connect

A first high pressure test was completed: 293 hr at 267 bar and 670{degrees}C; A parallel 1 bar test was done for comparison; Mass gains were higher for all alloys at 267 bar than at 1 bar; Longer term exposures, over a range of temperatures and pressures, are planned to provide information as to the commercial implications of pressure effects; The planned tests are at a higher combination of temperatures and pressures than in the existing literature. A comparison was made with longer-term literature data: The short term exposures are largely consistent with the longer-term corrosion literature; Ferritic steels--no consistent pressure effect; Austenitic steels--fine grain alloys less able to maintain protective chromia scale as pressure increases; Ni-base alloys--more mass gains above 105 bar than below. Not based on many data points.

Holcomb, Gordon R. [NETL; Carney, Casey [URS

2013-07-19T23:59:59.000Z

238

Enhanced High Resolution RBS System  

SciTech Connect

Improvements in full spectrum resolution with the second NEC high resolution RBS system are summarized. Results for 50 A ring TiN/HfO films on Si yielding energy resolution on the order of 1 keV are also presented. Detector enhancements include improved pulse processing electronics, upgraded shielding for the MCP/RAE detector, and reduced noise generated from pumping. Energy resolution measurements on spectra front edge coupled with calculations using 0.4mStr solid angle show that beam energy spread at 400 KeV from the Pelletron registered accelerator is less than 100 eV. To improve user throughput, magnet control has been added to the automatic data collection. Depth profiles derived from experimental data are discussed. For the thin films profiled, depth resolutions were on the Angstrom level with the non-linear energy/channel conversions ranging from 100 to 200 eV.

Pollock, Thomas J.; Hass, James A.; Klody, George M. [National Electrostatics Corp., Middleton, Wisconsin, U. S. A. 53562-0310 (United States)

2011-06-01T23:59:59.000Z

239

High voltage DC power supply  

DOE Patents (OSTI)

A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

Droege, T.F.

1989-12-19T23:59:59.000Z

240

High voltage load resistor array  

DOE Patents (OSTI)

A high voltage resistor comprising an array of a plurality of parallel electrically connected resistor elements each containing a resistive solution, attached at each end thereof to an end plate, and about the circumference of each of the end plates, a corona reduction ring. Each of the resistor elements comprises an insulating tube having an electrode inserted into each end thereof and held in position by one or more hose clamps about the outer periphery of the insulating tube. According to a preferred embodiment, the electrode is fabricated from stainless steel and has a mushroom shape at one end, that inserted into the tube, and a flat end for engagement with the end plates that provides connection of the resistor array and with a load.

Lehmann, Monty Ray (Smithfield, VA)

2005-01-18T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

High voltage DC power supply  

DOE Patents (OSTI)

A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

Droege, Thomas F. (Batavia, IL)

1989-01-01T23:59:59.000Z

242

High speed sampler and demultiplexer  

DOE Patents (OSTI)

A high speed sampling demultiplexer based on a plurality of sampler banks, each bank comprising a sample transmission line for transmitting an input signal, a strobe transmission line for transmitting a strobe signal, and a plurality of sampling gates at respective positions along the sample transmission line for sampling the input signal in response to the strobe signal. Strobe control circuitry is coupled to the plurality of banks, and supplies a sequence of bank strobe signals to the strobe transmission lines in each of the plurality of banks, and includes circuits for controlling the timing of the bank strobe signals among the banks of samplers. Input circuitry is included for supplying the input signal to be sampled to the plurality of sample transmission lines in the respective banks. The strobe control circuitry can repetitively strobe the plurality of banks of samplers such that the banks of samplers are cycled to create a long sample length. Second tier demultiplexing circuitry is coupled to each of the samplers in the plurality of banks. The second tier demultiplexing circuitry senses the sample taken by the corresponding sampler each time the bank in which the sampler is found is strobed. A plurality of such samples can be stored by the second tier demultiplexing circuitry for later processing. Repetitive sampling with the high speed transient sampler induces an effect known as "strobe kickout". The sample transmission lines include structures which reduce strobe kickout to acceptable levels, generally 60 dB below the signal, by absorbing the kickout pulses before the next sampling repetition.

McEwan, Thomas E. (Livermore, CA)

1995-01-01T23:59:59.000Z

243

High speed sampler and demultiplexer  

DOE Patents (OSTI)

A high speed sampling demultiplexer based on a plurality of sampler banks, each bank comprising a sample transmission line for transmitting an input signal, a strobe transmission line for transmitting a strobe signal, and a plurality of sampling gates at respective positions along the sample transmission line for sampling the input signal in response to the strobe signal. Strobe control circuitry is coupled to the plurality of banks, and supplies a sequence of bank strobe signals to the strobe transmission lines in each of the plurality of banks, and includes circuits for controlling the timing of the bank strobe signals among the banks of samplers. Input circuitry is included for supplying the input signal to be sampled to the plurality of sample transmission lines in the respective banks. The strobe control circuitry can repetitively strobe the plurality of banks of samplers such that the banks of samplers are cycled to create a long sample length. Second tier demultiplexing circuitry is coupled to each of the samplers in the plurality of banks. The second tier demultiplexing circuitry senses the sample taken by the corresponding sampler each time the bank in which the sampler is found is strobed. A plurality of such samples can be stored by the second tier demultiplexing circuitry for later processing. Repetitive sampling with the high speed transient sampler induces an effect known as ``strobe kickout``. The sample transmission lines include structures which reduce strobe kickout to acceptable levels, generally 60 dB below the signal, by absorbing the kickout pulses before the next sampling repetition. 16 figs.

McEwan, T.E.

1995-12-26T23:59:59.000Z

244

Nuclear Reactions at High Energy  

Science Journals Connector (OSTI)

In the quark model, nuclei (B?2) have exotic quantum numbers. Given a nuclear reaction in which certain quantum numbers are exchanged, what is the scattering amplitude at high energies, in the GeV region? Does it have Regge behavior? Is it dual? Are there multibaryon resonances? In this context we present a general survey of all high-energy nuclear reactions - mainly those involving light nuclei. For B=0 exchange reactions, like ?d??d and ?-h??0t (h?He3,t=H3), there is the impulse and rescattering (Glauber) model. For B=1 exchange we discuss the one-pion-exchange (OPE) model for pp?d?+, pd?dp, and ?d?pn, and the "knock-on" model for pd??+t, dd?tp, dh?hd, ?h?pd, and ???pt. In the case of B=2 exchange we examine the impulse and rescattering diagrams for ?d?d?, ?d?d?0, and ?d?d?, and use the OPE model to calculate cross sections for pd?t?, pt?tp, and ph?hp. Briefly considered are: (1) backward elastic scattering from heavy nuclei (pA?Ap) and (2) inclusive nuclear reactions such as N14+A?Li6+anything and pA?d+anything. We postulate that in general nuclear reactions have Regge behavior, but are not dual, because so far there are no exotic multibaryon resonances. Nuclear reactions appear to be completely dominated by anomalous singularities, whereas ordinary nonexotic hadron reactions appear to be dominated by normal singularities and poles.

George W. Barry

1973-03-01T23:59:59.000Z

245

ORNL - Restart of the High Flux Isotope Reactor 2-07  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Management Management OBJECTIVE MG-1: Line management has established programs to ensure safe accomplishment of work. Personnel exhibit awareness of public and worker safety, health, and environmental protection requirements, and through their actions, they demonstrate a high-priority commitment to comply with these requirements. (Core Requirements 1 and 2) Criteria * Line management has integrated programs within its existing ISMS and implementing mechanisms that appropriately address the major changes implemented during this outage, notably the CS, in order to continue to assure safe accomplishment of work. * Senior management and RRD management exhibit awareness of the applicable requirements pertaining to reactor operation, with emphasis on the

246

Rotational viscometer for high-pressure, high-temperature fluids  

DOE Patents (OSTI)

The invention is a novel rotational viscometer which is well adapted for use with fluids at high temperatures and/or pressures. In one embodiment, the viscometer include a substantially non-magnetic tube having a closed end and having an open end in communication with a fluid whose viscosity is to be determined. An annular drive magnet is mounted for rotation about the tube. The tube encompasses and supports a rotatable shaft assembly which carries a rotor, or bob, for insertion in the fluid. Affixed to the shaft are (a) a second magnet which is magnetically coupled to the drive magnet and (b) a third magnet. In a typical operation, the drive magnet is rotated to turn the shaft assembly while the shaft rotor is immersed in the fluid. The viscous drag on the rotor causes the shaft assembly to lag the rotation of the drive magnet by an amount which is a function of the amount of viscous drag. A first magnetic pickup generates a waveform whose phase is a function of the angular position of the drive magnet. A second magnetic pickup generates a waveform whose phase is a function of the angular position of the third magnet. Means are provided to generate an output indicative of the phase difference between the two waveforms. The viscometer is comparatively simple, inexpensive, rugged, and does not require shaft seals.

Carr, K.R.

1983-06-06T23:59:59.000Z

247

SENIOR PROJECT APPROVAL FORM Submit this completed form with your Honors Senior Project  

E-Print Network (OSTI)

SENIOR PROJECT APPROVAL FORM Submit this completed form with your Honors Senior Project I. PERSONAL: _______________________________________ Classification: Junior Senior II. PROJECT INFORMATION Type of Project: Thesis Group Project Internship Creative Project Study Abroad Service Learning Project Title

Huang, Haiying

248

Low Cost, High Efficiency, High Pressure Hydrogen Storage  

SciTech Connect

A technical and design evaluation was carried out to meet DOE hydrogen fuel targets for 2010. These targets consisted of a system gravimetric capacity of 2.0 kWh/kg, a system volumetric capacity of 1.5 kWh/L and a system cost of $4/kWh. In compressed hydrogen storage systems, the vast majority of the weight and volume is associated with the hydrogen storage tank. In order to meet gravimetric targets for compressed hydrogen tanks, 10,000 psi carbon resin composites were used to provide the high strength required as well as low weight. For the 10,000 psi tanks, carbon fiber is the largest portion of their cost. Quantum Technologies is a tier one hydrogen system supplier for automotive companies around the world. Over the course of the program Quantum focused on development of technology to allow the compressed hydrogen storage tank to meet DOE goals. At the start of the program in 2004 Quantum was supplying systems with a specific energy of 1.1-1.6 kWh/kg, a volumetric capacity of 1.3 kWh/L and a cost of $73/kWh. Based on the inequities between DOE targets and Quantums then current capabilities, focus was placed first on cost reduction and second on weight reduction. Both of these were to be accomplished without reduction of the fuel systems performance or reliability. Three distinct areas were investigated; optimization of composite structures, development of smart tanks that could monitor health of tank thus allowing for lower design safety factor, and the development of Cool Fuel technology to allow higher density gas to be stored, thus allowing smaller/lower pressure tanks that would hold the required fuel supply. The second phase of the project deals with three additional distinct tasks focusing on composite structure optimization, liner optimization, and metal.

Mark Leavitt

2010-03-31T23:59:59.000Z

249

NOvel Refractory Materials for High Alkali, High Temperature Environments  

SciTech Connect

Refractory materials can be limited in their application by many factors including chemical reactions between the service environment and the refractory material, mechanical degradation of the refractory material by the service environment, temperature limitations on the use of a particular refractory material, and the inability to install or repair the refractory material in a cost effective manner or while the vessel was in service. The objective of this project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al2O3 spinel or other similar magnesia/alumina containing unshaped refractory composition (castables, gunnables, shotcretes, etc) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, highalkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries. A research team was formed to carry out the proposed work led by Oak Ridge National Laboratory (ORNL) and was comprised of the academic institution Missouri University of Science and Technology (MS&T), and the industrial company MINTEQ International, Inc. (MINTEQ), along with representatives from the aluminum, chemical, glass, and forest products industries. The two goals of this project were to produce novel refractory compositions which will allow for improved energy efficiency and to develop new refractory application techniques which would improve the speed of installation. Also methods of hot installation were sought which would allow for hot repairs and on-line maintenance leading to reduced process downtimes and eliminating the need to cool and reheat process vessels.

Hemrick, J.G.; Griffin, R. (MINTEQ International, Inc.)

2011-08-30T23:59:59.000Z

250

HIGH-PERFORMANCE COATING MATERIALS  

SciTech Connect

Corrosion, erosion, oxidation, and fouling by scale deposits impose critical issues in selecting the metal components used at geothermal power plants operating at brine temperatures up to 300 C. Replacing these components is very costly and time consuming. Currently, components made of titanium alloy and stainless steel commonly are employed for dealing with these problems. However, another major consideration in using these metals is not only that they are considerably more expensive than carbon steel, but also the susceptibility of corrosion-preventing passive oxide layers that develop on their outermost surface sites to reactions with brine-induced scales, such as silicate, silica, and calcite. Such reactions lead to the formation of strong interfacial bonds between the scales and oxide layers, causing the accumulation of multiple layers of scales, and the impairment of the plant component's function and efficacy; furthermore, a substantial amount of time is entailed in removing them. This cleaning operation essential for reusing the components is one of the factors causing the increase in the plant's maintenance costs. If inexpensive carbon steel components could be coated and lined with cost-effective high-hydrothermal temperature stable, anti-corrosion, -oxidation, and -fouling materials, this would improve the power plant's economic factors by engendering a considerable reduction in capital investment, and a decrease in the costs of operations and maintenance through optimized maintenance schedules.

SUGAMA,T.

2007-01-01T23:59:59.000Z

251

High thermal expansion, sealing glass  

DOE Patents (OSTI)

A glass composition is described for hermetically sealing to high thermal expansion materials such as aluminum alloys, stainless steels, copper, and copper/beryllium alloys, which includes between about 10 and about 25 mole percent Na[sub 2]O, between about 10 and about 25 mole percent K[sub 2]O, between about 5 and about 15 mole percent Al[sub 2]O[sub 3], between about 35 and about 50 mole percent P[sub 2]O[sub 5] and between about 5 and about 15 mole percent of one of PbO, BaO, and mixtures thereof. The composition, which may also include between 0 and about 5 mole percent Fe[sub 2]O[sub 3] and between 0 and about 10 mole percent B[sub 2]O[sub 3], has a thermal expansion coefficient in a range of between about 160 and 210[times]10[sup [minus]7]/C and a dissolution rate in a range of between about 2[times]10[sup [minus]7] and 2[times]10[sup [minus]9]g/cm[sup 2]-min. This composition is suitable to hermetically seal to metallic electrical components which will be subjected to humid environments over an extended period of time.

Brow, R.K.; Kovacic, L.

1993-11-16T23:59:59.000Z

252

Multicolor, High Efficiency, Nanotextured LEDs  

SciTech Connect

We report on research results in this project which synergize advanced material science approaches with fundamental optical physics concepts pertaining to light-matter interaction, with the goal of solving seminal problems for the development of very high performance light emitting diodes (LEDs) in the blue and green for Solid State Lighting applications. Accomplishments in the duration of the contract period include (i) heteroepitaxy of nitrogen-polar LEDs on sapphire, (ii) heteroepitaxy of semipolar (11{bar 2}2) green LEDs on sapphire, (iii) synthesis of quantum-dot loaded nanoporous GaN that emits white light without phosphor conversion, (iv) demonstration of the highest quality semipolar (11{bar 2}2) GaN on sapphire using orientation-controlled epitaxy, (v) synthesis of nanoscale GaN and InGaN medium, and (vi) development of a novel liftoff process for manufacturing GaN thin-film vertical LEDs. The body of results is presented in this report shows how a solid foundation has been laid, with several noticeable accomplishments, for innovative research, consistent with the stated milestones.

Jung Han; Arto Nurmikko

2011-09-30T23:59:59.000Z

253

High Temperature Superconducting Underground Cable  

SciTech Connect

The purpose of this Project was to design, build, install and demonstrate the technical feasibility of an underground high temperature superconducting (HTS) power cable installed between two utility substations. In the first phase two HTS cables, 320 m and 30 m in length, were constructed using 1st generation BSCCO wire. The two 34.5 kV, 800 Arms, 48 MVA sections were connected together using a superconducting joint in an underground vault. In the second phase the 30 m BSCCO cable was replaced by one constructed with 2nd generation YBCO wire. 2nd generation wire is needed for commercialization because of inherent cost and performance benefits. Primary objectives of the Project were to build and operate an HTS cable system which demonstrates significant progress towards commercial progress and addresses real world utility concerns such as installation, maintenance, reliability and compatibility with the existing grid. Four key technical areas addressed were the HTS cable and terminations (where the cable connects to the grid), cryogenic refrigeration system, underground cable-to-cable joint (needed for replacement of cable sections) and cost-effective 2nd generation HTS wire. This was the worlds first installation and operation of an HTS cable underground, between two utility substations as well as the first to demonstrate a cable-to-cable joint, remote monitoring system and 2nd generation HTS.

Farrell, Roger, A.

2010-02-28T23:59:59.000Z

254

High risk of permafrost thaw  

SciTech Connect

In the Arctic, temperatures are rising fast, and permafrost is thawing. Carbon released to the atmosphere from permafrost soils could accelerate climate change, but the likely magnitude of this effect is still highly uncertain. A collective estimate made by a group of permafrost experts, including myself, is that carbon could be released more quickly than models currently suggest, and at levels that are cause for serious concern. While our models of carbon emission from permafrost thaw are lacking, experts intimately familiar with these landscapes and processes have accumulated knowledge about what they expect to happen, based on both quantitative data and qualitative understanding of these systems. We (the authors of this piece) attempted to quantify this expertise through a survey developed over several years, starting in 2009. Our survey asked experts what percentage of surface permafrost they thought was likely to thaw, how much carbon would be released, and how much of that would be methane, for three time periods and under four warming scenarios that are part of the new IPCC Fifth Assessment Report.

Schuur, E.A.G.; Abbott, B.; Koven, C.D,; Riley, W.J.; Subin, Z.M.; al, et

2011-11-01T23:59:59.000Z

255

High-Power Rf Load  

DOE Patents (OSTI)

A compact high-power RF load comprises a series of very low Q resonators, or chokes [16], in a circular waveguide [10]. The sequence of chokes absorb the RF power gradually in a short distance while keeping the bandwidth relatively wide. A polarizer [12] at the input end of the load is provided to convert incoming TE.sub.10 mode signals to circularly polarized TE.sub.11 mode signals. Because the load operates in the circularly polarized mode, the energy is uniformly and efficiently absorbed and the load is more compact than a rectangular load. Using these techniques, a load having a bandwidth of 500 MHz can be produced with an average power dissipation level of 1.5 kW at X-band, and a peak power dissipation of 100 MW. The load can be made from common lossy materials, such as stainless steel, and is less than 15 cm in length. These techniques can also produce loads for use as an alternative to ordinary waveguide loads in small and medium RF accelerators, in radar systems, and in other microwave applications. The design is easily scalable to other RF frequencies and adaptable to the use of other lossy materials.

Tantawi, Sami G. (San Mateo, CA); Vlieks, Arnold E. (Livermore, CA)

1998-09-01T23:59:59.000Z

256

APS high heat load monochromator  

SciTech Connect

This document contains the design specifications of the APS high heat load (HHL) monochromator and associated accessories as of February 1993. It should be noted that work is continuing on many parts of the monochromator including the mechanical design, crystal cooling designs, etc. Where appropriate, we have tried to add supporting documentation, references to published papers, and calculations from which we based our decisions. The underlying philosophy behind performance specifications of this monochromator was to fabricate a device that would be useful to as many APS users as possible, that is, the design should be as generic as possible. In other words, we believe that this design will be capable of operating on both bending magnet and ID beamlines (with the appropriate changes to the cooling and crystals) with both flat and inclined crystal geometries and with a variety of coolants. It was strongly felt that this monochromator should have good energy scanning capabilities over the classical energy range of about 4 to 20 keywith Si (111) crystals. For this reason, a design incorporating one rotation stage to drive both the first and second crystals was considered most promising. Separate rotary stages for the first and second crystals can sometimes provide more flexibility in their capacities to carry heavy loads (for heavily cooled first crystals or sagittal benders of second crystals), but their tuning capabilities were considered inferior to the single axis approach.

Lee, W.K.; Mills, D.

1993-02-01T23:59:59.000Z

257

High-pressure microhydraulic actuator  

DOE Patents (OSTI)

Electrokinetic ("EK") pumps convert electric to mechanical work when an electric field exerts a body force on ions in the Debye layer of a fluid in a packed bed, which then viscously drags the fluid. Porous silica and polymer monoliths (2.5-mm O.D., and 6-mm to 10-mm length) having a narrow pore size distribution have been developed that are capable of large pressure gradients (250-500 psi/mm) when large electric fields (1000-1500 V/cm) are applied. Flowrates up to 200 .mu.L/min and delivery pressures up to 1200 psi have been demonstrated. Forces up to 5 lb-force at 0.5 mm/s (12 mW) have been demonstrated with a battery-powered DC-DC converter. Hydraulic power of 17 mW (900 psi@ 180 uL/min) has been demonstrated with wall-powered high voltage supplies. The force and stroke delivered by an actuator utilizing an EK pump are shown to exceed the output of solenoids, stepper motors, and DC motors of similar size, despite the low thermodynamic efficiency.

Mosier, Bruce P. (San Francisco, CA) [San Francisco, CA; Crocker, Robert W. (Fremont, CA) [Fremont, CA; Patel, Kamlesh D. (Dublin, CA) [Dublin, CA

2008-06-10T23:59:59.000Z

258

High Performance Windows Volume Purchase: Information Resources  

NLE Websites -- All DOE Office Websites (Extended Search)

Information Information Resources to someone by E-mail Share High Performance Windows Volume Purchase: Information Resources on Facebook Tweet about High Performance Windows Volume Purchase: Information Resources on Twitter Bookmark High Performance Windows Volume Purchase: Information Resources on Google Bookmark High Performance Windows Volume Purchase: Information Resources on Delicious Rank High Performance Windows Volume Purchase: Information Resources on Digg Find More places to share High Performance Windows Volume Purchase: Information Resources on AddThis.com... Home About For Builders For Residential Buyers For Light Commercial Buyers For Manufacturers For Utilities Information Resources Information Resources Numerous publications will be available to help educate buyers, product

259

Optimizing High Level Waste Disposal  

SciTech Connect

If society is ever to reap the potential benefits of nuclear energy, technologists must close the fuel-cycle completely. A closed cycle equates to a continued supply of fuel and safe reactors, but also reliable and comprehensive closure of waste issues. High level waste (HLW) disposal in borosilicate glass (BSG) is based on 1970s era evaluations. This host matrix is very adaptable to sequestering a wide variety of radionuclides found in raffinates from spent fuel reprocessing. However, it is now known that the current system is far from optimal for disposal of the diverse HLW streams, and proven alternatives are available to reduce costs by billions of dollars. The basis for HLW disposal should be reassessed to consider extensive waste form and process technology research and development efforts, which have been conducted by the United States Department of Energy (USDOE), international agencies and the private sector. Matching the waste form to the waste chemistry and using currently available technology could increase the waste content in waste forms to 50% or more and double processing rates. Optimization of the HLW disposal system would accelerate HLW disposition and increase repository capacity. This does not necessarily require developing new waste forms, the emphasis should be on qualifying existing matrices to demonstrate protection equal to or better than the baseline glass performance. Also, this proposed effort does not necessarily require developing new technology concepts. The emphasis is on demonstrating existing technology that is clearly better (reliability, productivity, cost) than current technology, and justifying its use in future facilities or retrofitted facilities. Higher waste processing and disposal efficiency can be realized by performing the engineering analyses and trade-studies necessary to select the most efficient methods for processing the full spectrum of wastes across the nuclear complex. This paper will describe technologies being evaluated at Idaho National Laboratory and the facilities weve designed to evaluate options and support optimization.

Dirk Gombert

2005-09-01T23:59:59.000Z

260

High Level Waste System Plan Revision 9  

SciTech Connect

Revision 9 of the High Level Waste System Plan documents the current operating strategy of the HLW System at SRS to receive, store, treat, and dispose of high-level waste.

Davis, N.R.; Wells, M.N.; Choi, A.S.; Paul, P.; Wise, F.E.

1998-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Anomalous Interactions of High Energy Muons  

Science Journals Connector (OSTI)

......research-article Articles Anomalous Interactions of High Energy Muons Takashi Kitamura Reiji Sugano Department of Physics...on penetrating showers with large transferred energies producted by high energy muons are accepted, the muon would have anomalous......

Takashi Kitamura; Reiji Sugano

1966-11-01T23:59:59.000Z

262

High-Pressure Tube Trailers and Tanks  

Energy.gov (U.S. Department of Energy (DOE))

Presentation on High-Pressure Tube Trailers and Tanks for the DOE Hydrogen Delivery High-Pressure Tanks and Analysis Project Review Meeting held February 8-9, 2005 at Argonne National Laboratory

263

Development of High Energy Cathode Materials  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

deposits). Al-coated cell can is suitable for high-voltage cathodes. Polyethylene-based separators (such as Celgard K1640) are stable at high V. Carbon Additives...

264

Nuclear Interactions in Super High Energy Region  

Science Journals Connector (OSTI)

......research-article Articles Nuclear Interactions in Super High Energy Region Jose F. Bellandi a...Tokyo 188 We formulate the energy spectrum of produced particles...Atmospheric diffusion of high energy cosmic rays is calculated analytically......

Jose F. Bellandi; Sergio Q. Brunetto; Jose A. Chinellato; Carola Dobrigkeit; Akinori Ohsawa; Kotaro Sawayanagi; Edison H. Shibuya

1990-01-01T23:59:59.000Z

265

Identifying chromatin interactions at high spatial resolution  

E-Print Network (OSTI)

This thesis presents two computational approaches for identifying chromatin interactions at high spatial resolution from ChIA-PET data. We introduce SPROUT which is a hierarchical probabilistic model that discovers high ...

Reeder, Christopher Campbell

2014-01-01T23:59:59.000Z

266

Microfluidics for High School Chemistry Students  

Science Journals Connector (OSTI)

Microfluidics for High School Chemistry Students ... We present a laboratory experiment that introduces high school chemistry students to microfluidics while teaching fundamental properties of acidbase chemistry. ... Electrolysis of Water in the Secondary School Science Laboratory with Inexpensive Microfluidics ...

Melissa Hemling; John A. Crooks; Piercen M. Oliver; Katie Brenner; Jennifer Gilbertson; George C. Lisensky; Douglas B. Weibel

2013-12-09T23:59:59.000Z

267

High energy neutron Computed Tomography developed  

E-Print Network (OSTI)

be observed behind high-density materials, such as depleted uranium or tungsten. Comparison of the high (bottom half) and foam (center teeth) phantom could be viewed through 76 mm of depleted uranium. Some ~ 3

268

High Energy Density Ultracapacitors | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C. es038smith2010o.pdf More Documents & Publications High Energy Density Ultracapacitors High...

269

High Energy Density Ultracapacitors | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C. esp22smith.pdf More Documents & Publications High Energy Density Ultracapacitors High Energy...

270

Department of Physics High Energy Physics Group  

E-Print Network (OSTI)

Department of Physics High Energy Physics Group Electrical Engineer (Job ref: 0004) The High Energy and experience. A job description and an application form can be obtained from http

271

High-temperature thermocouples and related methods  

DOE Patents (OSTI)

A high-temperature thermocouple and methods for fabricating a thermocouple capable of long-term operation in high-temperature, hostile environments without significant signal degradation or shortened thermocouple lifetime due to heat induced brittleness.

Rempe, Joy L. (Idaho Falls, ID); Knudson, Darrell L. (Firth, ID); Condie, Keith G. (Idaho Falls, ID); Wilkins, S. Curt (Idaho Falls, ID)

2011-01-18T23:59:59.000Z

272

Highly durable graphene nanoplatelets supported Pt nanocatalysts...  

NLE Websites -- All DOE Office Websites (Extended Search)

durable graphene nanoplatelets supported Pt nanocatalysts for oxygen reduction . Highly durable graphene nanoplatelets supported Pt nanocatalysts for oxygen reduction . Abstract:...

273

Building America Webinar: High Performance Space Conditioning...  

Energy Savers (EERE)

Strategies for Affordable Housing Building America Webinar: High Performance Space Conditioning Systems, Part II - Air Distribution Retrofit Strategies for Affordable...

274

Reciprocity theorem in high-temperature superconductors  

E-Print Network (OSTI)

This article is devoted to the problem of the validity of the reciprocity theorem in high-temperature

Ivan Jane?ek

2002-01-01T23:59:59.000Z

275

Scaling in high-temperature superconductors by  

E-Print Network (OSTI)

A Hartree approximation is used to study the interplay of two kinds of scaling which arise in high-temperature

Ian D Lawrie

1994-01-01T23:59:59.000Z

276

Agenda: High Temperature Membrane Working Group Meeting  

Energy.gov (U.S. Department of Energy (DOE))

Agenda for the High Temperature Membrane Working Group (HTMWG) meeting on May 18, 2009, in Arlington, Virginia

277

Highly Automated Dipole EStimation , A. Pascarella2  

E-Print Network (OSTI)

filter, HADES (Highly Automatic Dipole EStimation). HADES is an open-source, freely downloadable, Matlab-based

Piana, Michele

278

SUPPORT FOR HU CFRT SUMMER HIGH SCHOOL FUSION WORKSHOP  

SciTech Connect

Nine summer fusion science research workshops for minority and female high school students were conducted at the Hampton University Center for Fusion Research and Training from 1996 to 2005. Each workshop was of the duration of eight weeks. In all 35 high school students were mentored. The students presented 28 contributed papers at the annual meetings of the American Physical Society Division of Plasma Physics. These contributed papers were very well received by the plasma physics and fusion science research community. The students won a number of prestigious local, state, and national honors, awards, prizes, and scholarships. The notable among these are the two regional finalist positions in the 1999 Siemens-Westinghouse Science and Technology Competitions; 1st Place U.S. Army Award, 2006; 1st Place U.S. Naval Science Award, 2006; Yale Science and Engineering Association Best 11th Grade Project, 2006; Society of Physics Students Book Award, 2006; APS Corporate Minority Scholarship and others. This workshop program conducted by the HU CFRT has been an exemplary success, and served the minority and female students exceptionally fruitfully. The Summer High School Fusion Science Workshop is an immensely successful outreach activity conducted by the HU CFRT. In this workshop, we train, motivate, and provide high quality research experiences to young and talented high school scholars with emphasis on under-represented minorities and female students in fusion science and related areas. The purpose of this workshop is to expose minority and female students to the excitement of research in science at an early stage in their academic lives. It is our hope that this may lead the high school students to pursue higher education and careers in physical sciences, mathematics, and perhaps in fusion science. To our knowledge, this workshop is the first and only one to date, of fusion science for under-represented minorities and female high school students at an HBCU. The faculty researchers in the HU CFRT mentor the students during summers. Mentors spend a considerable amount of time and efforts in training, teaching, guiding and supervising research projects. The HU CFRT has so far conducted nine workshops during the summers of 1996-2000 and 2002-2005. The first workshop was conducted in summer 1996. Students for the workshop are chosen from a national pool of exceptionally talented high school rising seniors/juniors. To our knowledge, most of these students have gone on to prestigious universities such as Duke University, John Hopkins University, CalTech, UCLA, Hampton University, etc. after completing their high school. For instance, Tiffany Fisher, participant of the 1996 summer workshop completed her BS in Mathematics at Hampton University in May 2001. She then went on to Wake Forest University at Winston-Salem, North Carolina to pursue graduate studies. Anshul Haldipur, participant of the 1999 summer workshop, began his undergraduate studies at Duke University in 2000. Christina Nguyen and Ilissa Martinez, participants of the 2000 summer workshop, are pursuing their undergraduate degrees at the UCLA and Florida State University respectively. The organizing committee of the APS DPP annual meeting invited Dr. Punjabi to deliver an invited talk on training the next generation of fusion scientists and engineers at the 2005 APS DPP meeting in Denver, CO. The organizing committee distributed a special flier with the Bulletin to highlight this invited talk and another talk on education as well the expo. This has given wide publicity and recognition to our workshops and Hampton University. Prof. Punjabi's talk: 'LI2 2: Training the next generation of fusion scientists and engineers: summer high school fusion science workshop, Bull. Amer. Phys. Soc. 50, 221 (2005)' was very well-received. He talked about HU education and outreach initiative and the HU CFRT Summer High School Workshop. The audience had a considerable number of questions about our workshops and the High School to PhD Pipeline in fusion science. Professor William Mathews of

Alkesh Punjabi

2010-02-09T23:59:59.000Z

279

NETL- High-Pressure Combustion Research Facility  

SciTech Connect

NETL's High-Pressure Combustion Facility is a unique resource within the National Laboratories system. It provides the test capabilities needed to evaluate new combustion concepts for high-pressure, high-temperature hydrogen and natural gas turbines. These concepts will be critical for the next generation of ultra clean, ultra efficient power systems.

None

2013-07-08T23:59:59.000Z

280

Tutorial: High Performance Computing Igal G. Rasin  

E-Print Network (OSTI)

Tutorial: High Performance Computing Igal G. Rasin Department of Chemical Engineering Israel Computing 27 Nisan 5769 (21.04.2009) 1 / 18 #12;Motivation What is High Performance Computing? What for serial Computing? Igal G. Rasin (Technion) Tutorial: High Performance Computing 27 Nisan 5769 (21

Adler, Joan

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

HIGH PERFORMANCE COMPUTING TODAY Jack Dongarra  

E-Print Network (OSTI)

1 HIGH PERFORMANCE COMPUTING TODAY Jack Dongarra Computer Science Department, University detailed and well-founded analysis of the state of high performance computing. This paper summarizes some of systems available for performing grid based computing. Keywords High performance computing, Parallel

Dongarra, Jack

282

College of Engineering High Performance Computing Cluster  

E-Print Network (OSTI)

College of Engineering High Performance Computing Cluster Policy and Procedures COE-HPC-01 and registered as requiring high performance computing; the course identification/registrations process the College High Performance Computing system will need register for system access by visiting http

Demirel, Melik C.

283

Electrical Transport Experiments at High Pressure  

SciTech Connect

High-pressure electrical measurements have a long history of use in the study of materials under ultra-high pressures. In recent years, electrical transport experiments have played a key role in the study of many interesting high pressure phenomena including pressure-induced superconductivity, insulator-to-metal transitions, and quantum critical behavior. High-pressure electrical transport experiments also play an important function in geophysics and the study of the Earth's interior. Besides electrical conductivity measurements, electrical transport experiments also encompass techniques for the study of the optoelectronic and thermoelectric properties of materials under high pressures. In addition, electrical transport techniques, i.e., the ability to extend electrically conductive wires from outside instrumentation into the high pressure sample chamber have been utilized to perform other types of experiments as well, such as high-pressure magnetic susceptibility and de Haas-van Alphen Fermi surface experiments. Finally, electrical transport techniques have also been utilized for delivering significant amounts of electrical power to high pressure samples, for the purpose of performing high-pressure and -temperature experiments. Thus, not only do high-pressure electrical transport experiments provide much interesting and valuable data on the physical properties of materials extreme compression, but the underlying high-pressure electrical transport techniques can be used in a number of ways to develop additional diagnostic techniques and to advance high pressure capabilities.

Weir, S

2009-02-11T23:59:59.000Z

284

High-Sulfur Coal for Generating Electricity  

Science Journals Connector (OSTI)

High-Sulfur...FLUIDIZED-BED COMBUSTORS, COMBUSTION...MAY FLUE GAS DES S E...1971 ). High-sulfur...was brief. Natural gas became...overdependent on natural gas and oil to...elevated pressure with a downward...coals of high ash-fusion...

James T. Dunham; Carl Rampacek; T. A. Henrie

1974-04-19T23:59:59.000Z

285

High Temperature Solar Splitting of Methane  

E-Print Network (OSTI)

-term commercialization opportunities #12;Why Use Solar Energy?Why Use Solar Energy? · High concentrations possible (>1000High Temperature Solar Splitting of Methane to Hydrogen and Carbon High Temperature Solar Splitting and worldwide) ­ Sufficient to power the world (if we choose to) · Advantages tradeoff against collection area

286

NETL- High-Pressure Combustion Research Facility  

ScienceCinema (OSTI)

NETL's High-Pressure Combustion Facility is a unique resource within the National Laboratories system. It provides the test capabilities needed to evaluate new combustion concepts for high-pressure, high-temperature hydrogen and natural gas turbines. These concepts will be critical for the next generation of ultra clean, ultra efficient power systems.

None

2014-06-26T23:59:59.000Z

287

QED3 Theory of High Temperature Superconductors  

E-Print Network (OSTI)

QED3 Theory of High Temperature Superconductors Zlatko Tesanovi´c The Johns Hopkins University is The Problem in high Tc superconductors? · Superconducting state appears dx2-y2 "BCS-like". Low energy: · Today, everything seems to be a high temperature superconduc- tor (cuprates, C60's, MgB2

Tesanovic, Zlatko

288

Radboud University Nijmegen Theoretical High Energy Physics  

E-Print Network (OSTI)

Radboud University Nijmegen Theoretical High Energy Physics Bachelor thesis The High Energy;CONTENTS CONTENTS Contents 1 Introduction and Research question 2 2 Theoretical Background 3 2.1 Gauge . . . . . . . . . . . . . . . . . . . . . . . . 4 2.3 High Energy Behaviour . . . . . . . . . . . . . . . . . . . . . . . 6 2.3.1 Renormalization

van Suijlekom, Walter

289

The Extended Finite Element Method for High Gradient Solutions  

E-Print Network (OSTI)

Outline Enrichment functions for high gradient solutions Motivation High gradient inside the domain (Shocks) High gradient at the boundary (boundary layers) Optimal set of enrichment functions Numerical for high gradient solutions Outline Enrichment functions for high gradient solutions Motivation High

290

Methods and technologies for high-throughput and high-content small animal screening  

E-Print Network (OSTI)

High-throughput and high-content screening (HTS and HCS) of whole animals requires their immobilization for high-resolution imaging and manipulation. Here we present methods to enable HTS and HCS of the nematode Caenorhabditis ...

Rohde, Christopher, 1979-

2012-01-01T23:59:59.000Z

291

Energy Performance and Comfort Level in High Rise and Highly Glazed Office Buildings  

E-Print Network (OSTI)

Thermal and visual comfort in buildings play a significant role on occupants' performance but on the other hand achieving energy savings and high comfort levels can be a quite difficult task especially in high rise buildings with highly glazed...

Bayraktar, M.; Perino, M.; Yilmaz, A. Z.

2010-01-01T23:59:59.000Z

292

Develop high energy high power Li-ion battery cathode materials : a first principles computational study  

E-Print Network (OSTI)

as cathode materials for Li-ion battery. Physica B-CondensedHigh Energy High Power Li-ion Battery Cathode Materials AHigh Energy High Power Li-ion Battery Cathode Materials A

Xu, Bo; Xu, Bo

2012-01-01T23:59:59.000Z

293

High Temperature, High Pressure Devices for Zonal Isolation in Geothermal Wells  

Energy.gov (U.S. Department of Energy (DOE))

DOE Geothermal Peer Review 2010 - Presentation. Project objectives: Design, demonstrate, and qualify high-temperature high pressure zonal isolation devices compatible with the high temperature downhole Enhanced Geothermal Systems (EGS) environment.

294

Precision Crystal Calorimeters in High Energy Physics  

ScienceCinema (OSTI)

Precision crystal calorimeters traditionally play an important role in high energy physics experiments. In the last two decades, it faces a challenge to maintain its precision in a hostile radiation environment. This paper reviews the performance of crystal calorimeters constructed for high energy physics experiments and the progress achieved in understanding crystal?s radiation damage as well as in developing high quality scintillating crystals for particle physics. Potential applications of new generation scintillating crystals of high density and high light yield, such as LSO and LYSO, in particle physics experiments is also discussed.

Ren-Yuan Zhu

2010-01-08T23:59:59.000Z

295

Deborah K. Smith Senior Scientist  

E-Print Network (OSTI)

Deborah K. Smith Senior Scientist Woods Hole Oceanographic Institution Publications: Jordan, T. H., H. W. Menard, and D.K. Smith, Density and size distribution of seamounts in the eastern Pacific inferred from wide-beam sounding data, J. Geophys. Res., 88, 10508-10518, 1983. Kim, I. I., D. K. Smith, H

Smith, Deborah K.

296

Halide and Oxy-Halide Eutectic Systems for High Performance High...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

High Performance High Temperature Heat Transfer Fluids Award Number: DE-FOA-0005942 Report Date: 15 January 2013 PI: Peiwen (Perry) Li * Numerical simulation and combined DSCTGA...

297

Modeling and Analysis of Natural Gas and Gasoline In A High Compression Ratio High Efficiency ICRE  

Energy.gov (U.S. Department of Energy (DOE))

performance of a high compression ratio (32:1 to 74:1) high efficiency (50 to 60% BTE) ICRE operating on natural gas and gasoline

298

Natural Gas Study Guide - High School | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

High School Natural Gas Study Guide - High School Natural Gas Study Guide - High School Natural Gas Study Guide - High School More Documents & Publications Natural Gas Study Guide...

299

NSF Division of Astronomical Sciences Senior Review NAIC Senior Review Memo Series  

E-Print Network (OSTI)

Sciences (AST) about its planning for a "Senior Review". The purpose of the Senior Review is to enable AST of the recent Decade Review of Astronomy and Astrophysics. This AST plan to assess and reallocate its facilitiesNSF Division of Astronomical Sciences Senior Review NAIC Senior Review Memo Series Memo #1

300

Honors College Senior Project What is the Honors College Senior Project?  

E-Print Network (OSTI)

Honors College Senior Project Overview What is the Honors College Senior Project? Individual departments have different expectations for completing the Honors Senior Project; thus, depending on your major, there are up to five options available to you. The unifying thread for all Honors Senior Projects

Huang, Haiying

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

High Performance Windows Volume Purchase: Contacts  

NLE Websites -- All DOE Office Websites (Extended Search)

Contacts to Contacts to someone by E-mail Share High Performance Windows Volume Purchase: Contacts on Facebook Tweet about High Performance Windows Volume Purchase: Contacts on Twitter Bookmark High Performance Windows Volume Purchase: Contacts on Google Bookmark High Performance Windows Volume Purchase: Contacts on Delicious Rank High Performance Windows Volume Purchase: Contacts on Digg Find More places to share High Performance Windows Volume Purchase: Contacts on AddThis.com... Home About For Builders For Residential Buyers For Light Commercial Buyers For Manufacturers For Utilities Information Resources Contacts Web site and High Performance Windows Volume Purchase Program contacts are provided below. Website Contact Send us your comments, report problems, and/or ask questions about

302

Ultra High Temperature | Open Energy Information  

Open Energy Info (EERE)

Ultra High Temperature Ultra High Temperature Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Print PDF Sanyal Temperature Classification: Ultra High Temperature Dictionary.png Ultra High Temperature: No definition has been provided for this term. Add a Definition Sanyal Temp Classification This temperature scheme was developed by Sanyal in 2005 at the request of DOE and GEA, as reported in Classification of Geothermal Systems: A Possible Scheme. Extremely Low Temperature Very Low Temperature Low Temperature Moderate Temperature High Temperature Ultra High Temperature Steam Field Reservoir fluid greater than 300°C is considered by Sanyal to be "ultra high temperature". "Such reservoirs are characterized by rapid development of steam saturation in the reservoir and steam fraction in the mobile fluid phase upon

303

High Energy Efficiency Air Conditioning  

SciTech Connect

This project determined the performance of a new high efficiency refrigerant, Ikon B, in a residential air conditioner designed to use R-22. The refrigerant R-22, used in residential and small commercial air conditioners, is being phased out of production in developed countries beginning this year because of concerns regarding its ozone depletion potential. Although a replacement refrigerant, R-410A, is available, it operates at much higher pressure than R-22 and requires new equipment. R-22 air conditioners will continue to be in use for many years to come. Air conditioning is a large part of expensive summer peak power use in many parts of the U.S. Previous testing and computer simulations of Ikon B indicated that it would have 20 - 25% higher coefficient of performance (COP, the amount of cooling obtained per energy used) than R-22 in an air-cooled air conditioner. In this project, a typical new R-22 residential air conditioner was obtained, installed in a large environmental chamber, instrumented, and run both with its original charge of R-22 and then with Ikon B. In the environmental chamber, controlled temperature and humidity could be maintained to obtain repeatable and comparable energy use results. Tests with Ikon B included runs with and without a power controller, and an extended run for several months with subsequent analyses to check compatibility of Ikon B with the air conditioner materials and lubricant. Baseline energy use of the air conditioner with its original R-22 charge was measured at 90 deg F and 100 deg F. After changeover to Ikon B and a larger expansion orifice, energy use was measured at 90 deg F and 100 deg F. Ikon B proved to have about 19% higher COP at 90 deg F and about 26% higher COP at 100 deg F versus R-22. Ikon B had about 20% lower cooling capacity at 90 deg F and about 17% lower cooling capacity at 100 deg F versus R-22 in this system. All results over multiple runs were within 1% relative standard deviation (RSD). All of these values agree well with previous results and computer simulations of Ikon B performance versus R-22. The lower cooling capacity of Ikon B is not a concern unless a particular air conditioner is near its maximum cooling capacity in application. Typically, oversized A/C systems are installed by contractors to cover contingencies. In the extended run with Ikon B, which lasted about 4.5 months at 100 deg F ambient temperature and 68% compressor on time, the air conditioner performed well with no significant loss of energy efficiency. Post-run analysis of the refrigerant, compressor lubricant oil, compressor, compressor outlet tubing, and the filter/dryer showed minor effects but nothing that was considered significant. The project was very successful. All objectives were achieved, and the performance of Ikon B indicates that it can easily be retrofitted into R-22 air conditioners to give 15 - 20% energy savings and a 1 - 3 year payback of retrofit costs depending on location and use. Ikon B has the potential to be a successful commercial product.

Edward McCullough; Patrick Dhooge; Jonathan Nimitz

2003-12-31T23:59:59.000Z

304

Mira Loma High School and Hopkins Junior High School from California Win  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Mira Loma High School and Hopkins Junior High School from Mira Loma High School and Hopkins Junior High School from California Win U.S. Department of Energy National Science Bowl Mira Loma High School and Hopkins Junior High School from California Win U.S. Department of Energy National Science Bowl May 4, 2009 - 12:00am Addthis WASHINGTON, DC - High school and middle school teams from California won the 2009 U.S. Department of Energy (DOE) National Science Bowl® today at the National Building Museum in Washington. Mira Loma High School from Sacramento beat Lexington High School from Lexington, Massachusetts in the high school national championship match. Hopkins Junior High School from Fremont, California beat Jonas Clarke Middle School from Lexington, Massachusetts in the middle school national championship match.

305

LOW-COMPLEXITY HIGH-SPEED 4-D TCM DECODER Jinjin He, Zhongfeng Wang, Senior Member, IEEE, and Huaping Liu  

E-Print Network (OSTI)

communications [1]. TCM gains noise immunity over uncoded transmission without expanding the signal bandwidth-dimensional signals is proposed. More recently, iterative Error Correction Codes (ECC) such as Turbo codes [5] and Low

Liu, Huaping

306

Public Meeting on Oversight of Complex, High Hazard Nuclear Operations - EM Statement - November 24, 2009  

NLE Websites -- All DOE Office Websites (Extended Search)

Defense Nuclear Facilities Safety Board Public Meeting on Defense Nuclear Facilities Safety Board Public Meeting on Oversight of Complex High Hazard Nuclear Operations Statement of Dr. Ines Triay Assistant Secretary, DOE Office of Environmental Management November 24, 2009 Good morning Mr. Vice Chairman and Members of the Defense Nuclear Facilities Safety Board. I appreciate the opportunity to be here today to represent the Department of Energy's Office of Environmental Management (EM) and address the actions our office has taken regarding oversight of complex high hazard nuclear operations. My remarks cover the six topics you provided to the Secretary in your letter dated August 25, 2009. Expectations of the senior Department of Energy (DOE) leadership with respect to safety philosophy and safety management approach.

307

423A HIGH-PERFORMANCE COMPUTING/NUMERICAL The International Journal of High Performance Computing Applications,  

E-Print Network (OSTI)

423A HIGH-PERFORMANCE COMPUTING/NUMERICAL The International Journal of High Performance Computing and barriers in the development of high-performance computing (HPC) algorithms and software. The activity has computing, numerical analy- sis, roadmap, applications and algorithms, software 1 The High-performance

Higham, Nicholas J.

308

High-Level Information Fusion and Mission Planning in Highly Anisotropic Threat Spaces  

E-Print Network (OSTI)

High-Level Information Fusion and Mission Planning in Highly Anisotropic Threat Spaces Mark sharing and high-level information fusion to allow for the visualisation of highly anisotropic threat options. Keywords: Information Fusion, Threat Map, Tactical Planning. 1 Introduction We present a first

Witkowski, Mark

309

High Energy Astrophysics: Overview 1/47 High Energy Astrophysics in Context  

E-Print Network (OSTI)

High Energy Astrophysics: Overview 1/47 High Energy Astrophysics in Context 1 Some references The following set of volumes is an outstanding summary of the field of High Energy Astrophysics and its relation to the rest of Astrophysics High Energy Astrophysics, Vols. 1,2 and 3. M.S. Longair, Cam- bridge University

Bicknell, Geoff

310

[ HIGH PERFORMANCE BUILDING STANDARD] STATE OF MONTANA HIGH PERFORMANCE BUILDING STANDARDS  

E-Print Network (OSTI)

[ HIGH PERFORMANCE BUILDING STANDARD] PART 2 HPBS STATE OF MONTANA HIGH PERFORMANCE BUILDING. These High Performance Building Standards are promulgated to implement the directives established in SB 49 which amended Section 17-7-201, MCA. B. These High Performance Building Standards were adopted on June 1

Dyer, Bill

311

Margaretta High School | Open Energy Information  

Open Energy Info (EERE)

Margaretta High School Margaretta High School Jump to: navigation, search Name Margaretta High School Facility Margaretta High School Sector Wind energy Facility Type Small Scale Wind Facility Status In Service Owner Margaretta High School Energy Purchaser Margaretta High School Location Castalia OH Coordinates 41.39923794°, -82.80122995° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.39923794,"lon":-82.80122995,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

312

Bellevue High School | Open Energy Information  

Open Energy Info (EERE)

Bellevue High School Bellevue High School Jump to: navigation, search Name Bellevue High School Facility Bellevue High School Sector Wind energy Facility Type Small Scale Wind Facility Status In Service Owner Bellevue High School Energy Purchaser Bellevue High School Location Bellevue WA Coordinates 41.28241024°, -82.84591019° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.28241024,"lon":-82.84591019,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

313

The high energy emission from black holes  

E-Print Network (OSTI)

The origin of the high energy emission (X-rays and gamma-rays) from black holes is still a matter of debate. We present new evidence that hard X-ray emission in the low/hard state may not be dominated by thermal Comptonization. We present an alternative scenario for the origin of the high energy emission that is well suited to explain the high energy emission from GRO J1655-40.

M. D. Caballero-Garcia; J. M. Miller; E. Kuulkers

2007-11-06T23:59:59.000Z

314

High Performance Buildings Database | Open Energy Information  

Open Energy Info (EERE)

High Performance Buildings Database High Performance Buildings Database Jump to: navigation, search The High Performance Buildings Database (HPBD), developed by the United States Department of Energy and the National Renewable Energy Laboratory, is "a unique central repository of in-depth information and data on high-performance, green building projects across the United States and abroad."[1] Map of HPBD entries Loading map... {"format":"googlemaps3","type":"ROADMAP","types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"limit":1000,"offset":0,"link":"all","sort":[""],"order":[],"headers":"show","mainlabel":"-","intro":"","outro":"","searchlabel":"\u2026

315

High Temperature Oxidation Resistance and Surface Electrical...  

NLE Websites -- All DOE Office Websites (Extended Search)

plates with oxidation resistant coatings. Candidate coatings must exhibit chemical and thermal-mechanical stability and high electrical conductivity during long-term...

316

HIGH-TECH BUILDINGS MARKET TRANSFORMATION PROJECT  

E-Print Network (OSTI)

LBNL-49112 HT-457 HIGH-TECH BUILDINGS MARKET TRANSFORMATION PROJECT Cleanroom Energy Benchmarking..............................................................................................................1 Cleanroom Energy Benchmarking..........................................................................................................................4 1. TASK ONE-CLEANROOM ENERGY BENCHMARKING........................................................5

317

Muons from high-energy cosmic photino  

Science Journals Connector (OSTI)

The muon production at photino-nucleon $$(\\bar \\gamma \\mathcal{N})$$ interaction for high-energy photino (E?)104GeV)...

V. S. Berezinsky; E. V. Bugaev; E. S. Zaslavskaya

318

High performance carbon nanocomposites for ultracapacitors  

DOE Patents (OSTI)

The present invention relates to composite electrodes for electrochemical devices, particularly to carbon nanotube composite electrodes for high performance electrochemical devices, such as ultracapacitors.

Lu, Wen

2012-10-02T23:59:59.000Z

319

DOE High Performance Computing Operational Review  

NLE Websites -- All DOE Office Websites (Extended Search)

HPCOR DOE High Performance Computing Operational Review (HPCOR) All logos Enabling Data-Driven Scientific Discovery at HPC Facilities June 18-19, 2014 California State University,...

320

NASA High Contrast Imaging for Exoplanets  

Science Journals Connector (OSTI)

Described is NASA's ongoing program for detection and characterization of exo-solar planets via high-contrast imaging. Some of the more promising proposed techniques under assessment...

Lyon, Richard

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Webinar: Highly Efficient Solar Thermochemical Reaction Systems  

Energy.gov (U.S. Department of Energy (DOE))

Video recording and text version of the Fuel Cell Technologies Office webinar titled "Highly Efficient Solar Thermochemical Reaction Systems," originally presented on January 13, 2015.

322

TAP Webinar: High Performance Outdoor Lighting Accelerator  

Energy.gov (U.S. Department of Energy (DOE))

Hosted by the Technical Assistance Program (TAP), this webinar will cover the recently announced expansion of the Better Buildings platform the High Performance Outdoor Lighting Accelerator (HPOLA).

323

A High-Performance PHEV Battery Pack  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

a reliable and highly efficient thermal management system Objective Simple Structure and Manufacturing Positive terminal Negative terminal Lead film (insulation tape) Stack and...

324

High-frequency resonances in photorefractive crystals  

Science Journals Connector (OSTI)

Two-wave mixing in photorefractive materials is investigated for the case of applied dc electric fields and large detuning frequencies and for high-frequency alternating electric...

Grunnet-Jepsen, A; Aubrecht, I; Solymar, L

1995-01-01T23:59:59.000Z

325

Making glue in high energy nuclear collisions  

E-Print Network (OSTI)

We discuss a real time, non-perturbative computation of the transverse dynamics of gluon fields at central rapidities in very high energy nuclear collisions.

Alex Krasnitz; Raju Venugopalan

1999-05-12T23:59:59.000Z

326

High School Internship | Princeton Plasma Physics Lab  

NLE Websites -- All DOE Office Websites (Extended Search)

High School Internships, students must be: United States citizens or permanent resident alien at the time of applying Able to obtain transportation to and from the laboratory. (The...

327

Highly Efficient Solar Thermochemical Reaction Systems  

Energy.gov (U.S. Department of Energy (DOE))

Download presentation slides from the DOE Fuel Cell Technologies Office webinar "Highly Efficient Solar Thermochemical Reaction Systems" held on January 13, 2015.

328

Nanostructured High Temperature Bulk Thermoelectric Energy Conversion...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Efficient Automotive Waste Heat Recovery Multi-physics modeling of thermoelectric generators for waste heat recovery applications Nanostructured High-Temperature Bulk...

329

High Temperature Thermoelectric Materials Characterization for...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

2009 -- Washington D.C. lmp06wang.pdf More Documents & Publications High-Temperature Thermoelectric Materials Characterization for Automotive Waste Heat Recovery: Success...

330

National High Magnetic Field Laboratory - Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

Lett. Physica B Physica C Physica E Polymer Polymer J. Proc. Physical Phenomena at High Magnetic Fields - IV Protein Science PROTEINS: Structure, Function and Genetics Rapid...

331

High-Pressure Model Catalyst System | EMSL  

NLE Websites -- All DOE Office Websites (Extended Search)

of one atmosphere or below in a reactor situated just below an ultra-high vacuum (UHV) chamber. In particular, heterogeneous catalytic reactions at realistic pressures over...

332

Materials Characterization Capabilities at the High Temperature...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Laboratory and HTML User Program Success Stories Materials Characterization Capabilities at the High Temperature Materials Laboratory: Focus on Carbon Fiber and Composites...

333

Multidisciplinary University Research Initiative: High Operating...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

University Research Initiative (MURI) to develop high-operating temperature heat-transfer fluids for concentrating solar power (CSP) applications. The following...

334

SAFETY PROCEDURE SP-24 NATIONAL HIGH MAGNETIC  

E-Print Network (OSTI)

SAFETY PROCEDURE SP-24 NATIONAL HIGH MAGNETIC FIELD LABORATORY NHMFL FLORIDA STATE UNIVERSITY SAFETY PROCEDURE SP-24 VISITOR AND CONTRACTOR SAFETY DIRECTOR, ENVIRONMENTAL, HEALTH, SAFETY & SECURITY Angela Sutton

Weston, Ken

335

National High Magnetic Field Laboratory - Scientist Profiles...  

NLE Websites -- All DOE Office Websites (Extended Search)

"Spatially resolved electronic structure inside and outside the vortex cores of a high-temperature superconductor", Nature 413, 501-504 (2001). 30. V. F. Mitrovi, E. E....

336

High Temperature Materials Laboratory (HTML) - PSD Directorate  

NLE Websites -- All DOE Office Websites (Extended Search)

filler A National Resource for Collaborative Materials Research The High Temperature Materials Laboratory (HTML) User Program is on hiatus due to federal budget reductions....

337

Nanostructured Thermoelectric Materials and High Efficiency Power...  

NLE Websites -- All DOE Office Websites (Extended Search)

Nanostructured Thermoelectric Materials and High Efficiency Power Generation Modules Home Author: T. Hogan, A. Downey, J. Short, S. D. Mahanti, H. Schock, E. Case Year: 2007...

338

High Throughput Single Molecule Investigation of Transcription  

E-Print Network (OSTI)

genomic DNA based on single-molecule detection. Analyticalmapping: a novel, single- molecule approach to genomic2011). High-throughput single-molecule optofluidic analysis.

Kim, Soohong

2012-01-01T23:59:59.000Z

339

Developing High Capacity, Long Life Anodes  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

long life and improved Safety for PHEV and EV applications. Objectives Develop a low cost synthesis methods to prepare high energy anodes Full structural and...

340

High temperature elemental losses and mineralogical  

E-Print Network (OSTI)

future energy crops. Combustion in biomass fueled boilers,in ash during combustion of biomass fuels is important forC. Combustion characteristics of high alkali biomass. Final

Thy, P.; Jenkins, B. M.; Grundvig, S.; Shiraki, R.; Lesher, C. E.

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

High-speed digital color imaging pyrometry  

Science Journals Connector (OSTI)

Temperature measurements of high-explosive and combustion processes are difficult to obtain due to the speed and environment of the events. To overcome these challenges, we have...

Densmore, John M; Biss, Matthew M; McNesby, Kevin L; Homan, Barrie E

2011-01-01T23:59:59.000Z

342

High-Powered Lasers for Clean Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

extremely high temperatures and pressures. The controlled release of fusion, or thermonuclear energy, in the laboratory remains an alluring goal due to its potential as a...

343

Polymerizable Additive for Passivating High Voltage Cathodes  

NLE Websites -- All DOE Office Websites (Extended Search)

batteries with the goal of significantly increasing battery energy density. Conventional Li-ion battery electrolyte systems are quite unstable at these high potentials, leading to...

344

Experimental Analysis of Water Based Drilling Fluid Aging Processes at High Temperature and High Pressure Conditions  

E-Print Network (OSTI)

! ! EXPERIMENTAL ANALYSIS OF WATER BASED DRILLING FLUID AGING PROCESSES AT HIGH TEMPERATURE AND HIGH PRESSURE CONDITIONS A Thesis by BRANDON SCOTT ZIGMOND Submitted to the Office of Graduate Studies of Texas A&M University... Temperature and High Pressure Conditions Copyright 2012 Brandon Scott Zigmond ! ! EXPERIMENTAL ANALYSIS OF WATER BASED DRILLING FLUID AGING PROCESSES AT HIGH TEMPERATURE AND HIGH PRESSURE CONDITIONS A Thesis by BRANDON SCOTT ZIGMOND Submitted...

Zigmond, Brandon

2012-10-19T23:59:59.000Z

345

On-chip high speed localized cooling using superlattice microrefrigerators  

E-Print Network (OSTI)

cooling, microrefrigerators, optoelectronics, superlattice,in high power, high-speed optoelectronics devices, and

Zhang, Y; Christofferson, J; Shakouri, A; Zeng, G H; Bowers, J E; Croke, E T

2006-01-01T23:59:59.000Z

346

Electrochemical investigations of various high-temperature superconductor phases  

Science Journals Connector (OSTI)

Electrochemical investigations of various high-temperature superconductor phases ... Electrochemistry of High-Temperature Superconductors ...

David R. Riley; A. Manthiram; John T. McDevitt

1992-11-01T23:59:59.000Z

347

HIGH PERFORMANCE COMPUTING INITIATIVE What Is It?  

E-Print Network (OSTI)

of power, and generate high amounts of heat.2 Rooms equipped to handle HPC should have redundant environmental controls to avoid data loss, dedicated power sources (with appropriate emergency backup power today to design an HPPC cluster of 36 nodes plus network switches in one seven-foot-high rack. If each

Weber, David J.

348

Superconducting high-pressure phases of disilane  

Science Journals Connector (OSTI)

...Superconducting high-pressure phases of disilane 10.1073/pnas.1005242107 Xilian...DC 20015 High-pressure structures of disilane (Si2H6) are investigated extensively...linear-response calculations for Pm-3m disilane at 275 GPa show a large electron-phonon...

Xilian Jin; Xing Meng; Zhi He; Yanming Ma; Bingbing Liu; Tian Cui; Guangtian Zou; Ho-kwang Mao

2010-01-01T23:59:59.000Z

349

Radiation Weighting Factors and High Energy Radiation  

Science Journals Connector (OSTI)

......generally inadequate for high energy radiation. In order to determine...appropriate wR values in the high energy region, several criteria are...are proposed for neutrons of energy above 100 MeV and for protons above 10 MeV. The wR value for muons is confirmed to be practically......

M. Pelliccioni

1998-12-01T23:59:59.000Z

350

Spread of Detonation in High Explosives  

Science Journals Connector (OSTI)

... W. C. F. Shepherd makes the interesting observation that in the initial stages of detonation in a cylindrical cartridge of high explosive initiated with a detonator, a phase, referred ... of high explosive initiated with a detonator, a phase, referred to as the pre-detonation phase, is often noticeable during which the rate of propagation of the reaction is ...

ELWYN JONES; DUGALD MITCHELL

1948-01-17T23:59:59.000Z

351

Development of High Voltage Electron Microscope  

Science Journals Connector (OSTI)

......Cockcroft Walton Type High Voltage Generator. O Power Line O Fig. 4...pressure in the tank to the atmospheric pressure by removing freon...pump using liquid nitrogen. Water buffer and liquid nitrogen...base plate of high voltage generator. Four poles stand on this......

Shinjiro KATAGIRI; Hirokazu KIMURA; Susumu OZASA; Kazumi SHIRAISHI

1969-01-01T23:59:59.000Z

352

Limitations of High-Voltage Insulation  

Science Journals Connector (OSTI)

... materials such as impregnated paper. The important electrical properties of the materials used for the insulation of high-voltage circuits are conductivity and electric strength. The conductivity measures the ability ... a million times between themselves, but they are all classified as available for high-voltage insulation.

1938-01-08T23:59:59.000Z

353

Progress in High-Entropy Alloys  

SciTech Connect

Strictly speaking, high-entropy alloys (HEAs) refer to single-phase, solid-solution alloys with multiprincipal elements in an equal or a near-equal molar ratio whose configurational entropy is tremendously high. This special topic was organized to reflect the focus and diversity of HEA research topics in the community.

Gao, Michael C.

2013-12-01T23:59:59.000Z

354

High-Frequency Transient Eddies and Blocking  

Science Journals Connector (OSTI)

In this paper we investigate the role of high-frequency transient eddies in the maintenance of the blocking high which occurred over Europe on 16-25 February 1979. Time-filtering is used to decompose the atmospheric large-scale flow into ...

Eero Holopainen; Carl Fortelius

1987-06-01T23:59:59.000Z

355

High Temperature, Permanent Magnet Biased Magnetic Bearings  

E-Print Network (OSTI)

performance, high speed and high temperature applications like space vehicles, jet engines and deep sea equipment. The bearing system had a target design to carry a load equal to 500 lb-f (2225N). Another objective was to design and build a test rig fixture...

Gandhi, Varun R.

2010-07-14T23:59:59.000Z

356

High power laser perforating tools and systems  

DOE Patents (OSTI)

ystems devices and methods for the transmission of 1 kW or more of laser energy deep into the earth and for the suppression of associated nonlinear phenomena. Systems, devices and methods for the laser perforation of a borehole in the earth. These systems can deliver high power laser energy down a deep borehole, while maintaining the high power to perforate such boreholes.

Zediker, Mark S; Rinzler, Charles C; Faircloth, Brian O; Koblick, Yeshaya; Moxley, Joel F

2014-04-22T23:59:59.000Z

357

American Heart Month National High Blood  

E-Print Network (OSTI)

FEBRUARY American Heart Month MAY National High Blood Pressure Education Month SEPTEMBER National Cholesterol Education Month Texas AgriLife Extension Service Texas A&M University System Eat Smart for Heart for Heart Health # P2-2 Risk Factors - High Blood Pressure # P2-3 Sodium is needed to. . . # P2-4 Sources

358

Modulation instability in high power laser amplifiers  

E-Print Network (OSTI)

. Widmayer, R. K. White, S. T. Yang, and B. M. VanWonterghem, "National Ignition Facility laser performanceModulation instability in high power laser amplifiers Alexander M. Rubenchik,1,* Sergey K. Turitsyn in high-power laser systems. The so-called B-integral restriction is commonly used as the criteria for MI

Turitsyn, Sergei K.

359

High-Sulfur Coal for Generating Electricity  

Science Journals Connector (OSTI)

...amounts of coal, because...Director-Mineral Re-sources...of Gas from Coal through a...on coals of high ash-fusion temperature...per ton of high-sulfur coal burned. Absorp-tion...particulate matter as well as...capable of remov-ing up to...

James T. Dunham; Carl Rampacek; T. A. Henrie

1974-04-19T23:59:59.000Z

360

High resolution scintillation detector with semiconductor readout  

DOE Patents (OSTI)

A novel high resolution scintillation detector array for use in radiation imaging such as high resolution Positron Emission Tomography (PET) which comprises one or more parallelepiped crystals with at least one long surface of each crystal being in intimate contact with a semiconductor photodetector such that photons generated within each crystal by gamma radiation passing therethrough is detected by the photodetector paired therewith.

Levin, Craig S. (Santa Monica, CA); Hoffman, Edward J. (Los Angeles, CA)

2000-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

High Voltage Safety Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

High Voltage Safety Act High Voltage Safety Act High Voltage Safety Act < Back Eligibility Commercial Construction Developer General Public/Consumer Industrial Installer/Contractor Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Georgia Program Type Safety and Operational Guidelines Siting and Permitting The purpose of the High Voltage Safety Act is to prevent injury to persons and property and interruptions of utility service resulting from accidental or inadvertent contact with high-voltage electric lines by providing that no work shall be done in the vicinity of such lines unless and until the owner or operator thereof has been notified of such work and has taken the appropriate safety measures. The Georgia Public Service Commission requires

362

High Tech and Industrial Systems Group  

NLE Websites -- All DOE Office Websites (Extended Search)

High Tech and Industrial Systems Group High Tech and Industrial Systems Group Some of the largest energy users in today's economy are high tech buildings and industrial systems. They operate up to 24 hours per day with energy intensities much greater than typical commercial or residential buildings, and they are essential to the national economy. High-tech buildings, such as laboratories, cleanrooms, data centers, and hospitals, are characterized by large base-loads, continuous operation, and high energy-use intensities. These buildings crosscut many industries and institutions. Group activities and products include: benchmarking surveys and metrics, case study reports, technology development, technology demonstrations, assessment and profiling tools, best practice guides, workshops, training guides, and development of other strategies.

363

Conformal coating of highly structured surfaces  

DOE Patents (OSTI)

Method of applying a conformal coating to a highly structured substrate and devices made by the disclosed methods are disclosed. An example method includes the deposition of a substantially contiguous layer of a material upon a highly structured surface within a deposition process chamber. The highly structured surface may be associated with a substrate or another layer deposited on a substrate. The method includes depositing a material having an amorphous structure on the highly structured surface at a deposition pressure of equal to or less than about 3 mTorr. The method may also include removing a portion of the amorphous material deposited on selected surfaces and depositing additional amorphous material on the highly structured surface.

Ginley, David S.; Perkins, John; Berry, Joseph; Gennett, Thomas

2012-12-11T23:59:59.000Z

364

HIGH AVERAGE POWER OPTICAL FEL AMPLIFIERS.  

SciTech Connect

Historically, the first demonstration of the optical FEL was in an amplifier configuration at Stanford University [l]. There were other notable instances of amplifying a seed laser, such as the LLNL PALADIN amplifier [2] and the BNL ATF High-Gain Harmonic Generation FEL [3]. However, for the most part FELs are operated as oscillators or self amplified spontaneous emission devices. Yet, in wavelength regimes where a conventional laser seed can be used, the FEL can be used as an amplifier. One promising application is for very high average power generation, for instance FEL's with average power of 100 kW or more. The high electron beam power, high brightness and high efficiency that can be achieved with photoinjectors and superconducting Energy Recovery Linacs (ERL) combine well with the high-gain FEL amplifier to produce unprecedented average power FELs. This combination has a number of advantages. In particular, we show that for a given FEL power, an FEL amplifier can introduce lower energy spread in the beam as compared to a traditional oscillator. This properly gives the ERL based FEL amplifier a great wall-plug to optical power efficiency advantage. The optics for an amplifier is simple and compact. In addition to the general features of the high average power FEL amplifier, we will look at a 100 kW class FEL amplifier is being designed to operate on the 0.5 ampere Energy Recovery Linac which is under construction at Brookhaven National Laboratory's Collider-Accelerator Department.

BEN-ZVI, ILAN, DAYRAN, D.; LITVINENKO, V.

2005-08-21T23:59:59.000Z

365

Aeroacoustic sources of high speed maglev trains  

Science Journals Connector (OSTI)

Noise has been identified as a potential source of concern associated with the introduction of high speed maglev trains into the existing transportation system in the United States. The first operational maglev systems have been shown to generate high noise levels at high speeds with noise levels over 100 dBA at 25 m typical for the maximum cruising speeds. At speeds greater than 150 miles per hour the dominant noise source is of aerodynamic origin proportional to the 6th power of velocity at high speeds and 8th power dependency at very high speeds. An investigation of the noisegenerated by maglev systems was conducted to determine noise sources develop noise criteria for high speed maglev systems prepare design guidelines for noise control and recommend an acoustic test facility for maglev research. This paper describes the findings of the study including recommendations for further research to develop a better understanding of the aerodynamic soundgeneration associated with high speed maglev operations. [Work performed under contract to U.S. Department of Transportation as part of the National Maglev Initiative.

Carl E. Hanson

1994-01-01T23:59:59.000Z

366

Vehicle Technologies Office Merit Review 2014: High Energy High Power Battery Exceeding PHEV-40 Requirements  

Energy.gov (U.S. Department of Energy (DOE))

Presentation given by [company name] at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about high energy high power battery...

367

Flexible composition and execution of high performance, high fidelity multiscale biomedical simulations  

Science Journals Connector (OSTI)

...execution time. multiscale modelling|blood flow|high performance computing|in-stent restenosis|cerebrovascular bloodflow...brain blood flow. In 2011 Int. Conf. for High Performance Computing, Networking, Storage and Analysis (SC...

2013-01-01T23:59:59.000Z

368

Novel Concept for Generating High Beam Quality from High Pulse Energy Optical Parametric Oscillators  

Science Journals Connector (OSTI)

Highly improved beam quality from a high pulse energy OPO is demonstrated by using a resonator with two different types of crystals type 2 phase matched for the same interaction, but...

Farsund, ystein; Arisholm, Gunnar; Rustad, Gunnar

369

High Repetition Rate, High Energy Fiber CPA System for Material Processing  

Science Journals Connector (OSTI)

We report on a fiber based CPA system generating 100 J of ultra-short pulses at high repetition rates (56 kHz). In a first application, the pulses are used for high speed hole...

Schreiber, Thomas; Rser, Fabian; Limpert, Jens; Liem, Andreas; Hfer, Sven; Zellmer, Holger; Will, Matthias; Nolte, Stefan; Tnnermann, Andreas

370

High Energy Density Sate, Material and Device with High Power Lasers  

Science Journals Connector (OSTI)

High energy density states with photon pressures of more than Tera bar and thermal pressure of more than Mega bar, is now available with high power lasers. Here I present creation of...

Kodama, R

371

High-Capacity High-Energy Ball Mill for Nanophase Materials  

Science Journals Connector (OSTI)

A high-energy high-capacity ball mill, which can be easily ... scaled-up, for the synthesis of nanophase materials is described. The synthesis of nanophase iron...

Diego Basset; Paolo Matteazzi; Fabio Miani

1994-01-01T23:59:59.000Z

372

Generation of high power, high repetition-rate pulses using erbium-doped fiber ring laser  

E-Print Network (OSTI)

This thesis presents the results obtained from crographics. generation of high repetition rate, high peak power output pulses using an erbium-doped fiber amplifier (EDFA). Two configurations were employed. The first setup used a linear cavity...

Hinson, Brett Darren

2012-06-07T23:59:59.000Z

373

High Energy Density Li-ion Cells for EVs Based on Novel, High...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Storage Systems Vehicle Technologies Annual Merit Review 6182014 1 High Energy Density Li-ion Cells for EV's Based on Novel, High Voltage Cathode Material Systems Keith D. Kepler...

374

Hybrid high direct current circuit interrupter  

DOE Patents (OSTI)

A device and a method are disclosed for interrupting very high direct currents (greater than 100,000 amperes) and simultaneously blocking high voltages (greater than 600 volts). The device utilizes a mechanical switch to carry very high currents continuously with low loss and a silicon controlled rectifier (SCR) to bypass the current around the mechanical switch while its contacts are separating. A commutation circuit, connected in parallel with the SCR, turns off the SCR by utilizing a resonant circuit to divert the SCR current after the switch opens. 7 figs.

Rockot, J.H.; Mikesell, H.E.; Jha, K.N.

1998-08-11T23:59:59.000Z

375

Hybrid high direct current circuit interrupter  

DOE Patents (OSTI)

A device and a method for interrupting very high direct currents (greater than 100,000 amperes) and simultaneously blocking high voltages (greater than 600 volts). The device utilizes a mechanical switch to carry very high currents continuously with low loss and a silicon controlled rectifier (SCR) to bypass the current around the mechanical switch while its contacts are separating. A commutation circuit, connected in parallel with the SCR, turns off the SCR by utilizing a resonant circuit to divert the SCR current after the switch opens.

Rockot, Joseph H. (N. Huntingdon, PA); Mikesell, Harvey E. (McMurray, PA); Jha, Kamal N. (Bethel Park, PA)

1998-01-01T23:59:59.000Z

376

Explosive-driven, high speed, arcless switch  

DOE Patents (OSTI)

An explosive-actuated, fast-acting arcless switch contains a highly conductive foil to carry high currents positioned adjacent a dielectric surface within a casing. At one side of the foil opposite the dielectric surface is an explosive which, when detonated, drives the conductive foil against the dielectric surface. A pattern of grooves in the dielectric surface ruptures the foil to establish a rupture path having a pattern corresponding to the pattern of the grooves. The impedance of the ruptured foil is greater than that of the original foil to divert high current to a load. Planar and cylindrical embodiments of the switch are disclosed.

Skogmo, P.J.; Tucker, T.J.

1986-05-02T23:59:59.000Z

377

Explosive-driven, high speed, arcless switch  

DOE Patents (OSTI)

An explosive-actuated, fast-acting arcless switch contains a highly conductive foil to carry high currents positioned adjacent a dielectric surface within a casing. At one side of the foil opposite the dielectric surface is an explosive which, when detonated, drives the conductive foil against the dielectric surface. A pattern of grooves in the dielectric surface ruptures the foil to establish a rupture path having a pattern corresponding to the pattern of the grooves. The impedance of the ruptured foil is greater than that of the original foil to divert high current to a load. Planar and cylindrical embodiments of the switch are disclosed. 7 figs.

Skogmo, P.J.; Tucker, T.J.

1987-07-14T23:59:59.000Z

378

Symposium on high temperature and materials chemistry  

SciTech Connect

This volume contains the written proceedings of the Symposium on High Temperature and Materials Chemistry held in Berkeley, California on October 24--25, 1989. The Symposium was sponsored by the Materials and Chemical Sciences Division of Lawrence Berkeley Laboratory and by the College of Chemistry of the University of California at Berkeley to discuss directions, trends, and accomplishments in the field of high temperature and materials chemistry. Its purpose was to provide a snapshot of high temperature and materials chemistry and, in so doing, to define status and directions.

Not Available

1989-10-01T23:59:59.000Z

379

High-pressure liquid chromatographic gradient mixer  

DOE Patents (OSTI)

A gradient mixer effects the continuous mixing of any two miscible solvents without excessive decay or dispersion of the resultant isocratic effluent or of a linear or exponential gradient. The two solvents are fed under low or high pressure by means of two high performance liquid chromatographic pumps. The mixer comprises a series of ultra-low dead volume stainless steel tubes and low dead volume chambers. The two solvent streams impinge head-on at high fluxes. This initial nonhomogeneous mixture is then passed through a chamber packed with spirally-wound wires which cause turbulent mixing thereby homogenizing the mixture with minimum band-broadening.

Daughton, C.G.; Sakaji, R.H.

1982-09-08T23:59:59.000Z

380

AGILA: The Ateneo High Performance Computing System  

E-Print Network (OSTI)

A Beowulf cluster is a low-cost parallel high performance computing system that uses commodity hardware components such as personal computers and standard Ethernet adapters and switches and runs on freely available software such as Linux and LAM-MPI. In this paper the development of the AGILA HPCS, which stands for the Ateneo GigaflopsRange Performance, Linux OS, and Athlon Processors High Performance Computing System, is discussed including its hardware and software configurations and performance evaluation. Keywords High-performance computing, commodity cluster computing, parallel computing, Beowulf-class cluster 1.

Rafael Salda Na; Felix P. Muga Ii; Jerrold J. Garcia; William Emmanuel; S. Yu

2000-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Proppant Fracture Conductivity with High Proppant Loading and High Closure Stress  

E-Print Network (OSTI)

PROPPANT FRACTURE CONDUCTIVITY WITH HIGH PROPPANT LOADING AND HIGH CLOSURE STRESS A Thesis by MATTHEW CHARLES RIVERS Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE May 2010 Major Subject: Petroleum Engineering PROPPANT FRACTURE CONDUCTIVITY WITH HIGH PROPPANT LOADING AND HIGH CLOSURE STRESS A Thesis by MATTHEW CHARLES RIVERS Submitted...

Rivers, Matthew Charles

2011-08-08T23:59:59.000Z

382

Soft Magnetic Materials in High-Frequency, High-Power Conversion Applications  

E-Print Network (OSTI)

Voltage DC (HVDC) technologies aim to improve the effi- ciency of power networks and benefit from high

McHenry, Michael E.

383

ENERGY STAR Score for Senior Care Communities  

NLE Websites -- All DOE Office Websites (Extended Search)

Senior Care Communities in the United States Page 1 Senior Care Communities in the United States Page 1 ENERGY STAR Score for Senior Care Communities in the United States Technical Reference OVERVIEW The ENERGY STAR Score for Senior Care Communities applies to buildings that house and provide care and assistance for elderly residents. The objective of the ENERGY STAR score is to provide a fair assessment of the energy performance of a property relative to its peers, taking into account the climate, weather, and business activities at the property. To identify the aspects of building activity that are significant drivers of energy use and then

384

BEHAVIOR OF CONCRETE BRIDGE DECKS REINFORCED WITH HIGH-STRENGTH AND HIGH CORROSION-RESISTANT STEEL  

E-Print Network (OSTI)

BEHAVIOR OF CONCRETE BRIDGE DECKS REINFORCED WITH HIGH- STRENGTH AND HIGH CORROSION-RESISTANT STEEL, high corrosion-resistant steel commercially known as Micro-composite Multi-structural Formable (MMFX) steel. The study included testing three full-scale bridge decks having a span-to-depth ratio of 12

385

High Efficiency and High Rate Deposited Amorphous Silicon-Based Solar Cells  

E-Print Network (OSTI)

. Figure 3-1 IV curve of a UT fabricated triple cell, showing 12.7% initial, active-area efficiency. Figure1 High Efficiency and High Rate Deposited Amorphous Silicon-Based Solar Cells PHASE I Annual-junction a-Si Solar Cells with Heavily Doped Thin Interface Layers at the Tunnel Junctions Section 4 High

Deng, Xunming

386

High-Temperature Superconducting Cable Testing Gregory S. Boebinger, National High Magnetic Field Laboratory  

E-Print Network (OSTI)

High-Temperature Superconducting Cable Testing Gregory S. Boebinger, National High Magnetic Field-Temperature Superconducting (HTS) Cables are desirable for application in large high-field magnets (>20 T), especially when). Of the three HTS magnet cable concepts emerging, the Conductor On Round Core was the first that was tested

Weston, Ken

387

High performance computing: Clusters, constellations, MPPs, and future directions  

E-Print Network (OSTI)

and Jim Gray, High Performance Computing: Crays, Clusters,The Marketplace of High-Performance Computing, ParallelHigh Performance Computing Clusters, Constellations, MPPs,

Dongarra, Jack; Sterling, Thomas; Simon, Horst; Strohmaier, Erich

2003-01-01T23:59:59.000Z

388

High-performance computer system installed at Los Alamos National...  

NLE Websites -- All DOE Office Websites (Extended Search)

High-performance computer system installed at Lab High-performance computer system installed at Los Alamos National Laboratory New high-performance computer system, called Wolf,...

389

High-performance LED street lighting using microlens arrays  

Science Journals Connector (OSTI)

An efficient LED lamp that illuminates the street with high quality is presented. The luminaire shows high optical efficiency, high optical utilization factor, low glare, and...

Lee, Xuan-Hao; Moreno, Ivan; Sun, Ching-Cherng

2013-01-01T23:59:59.000Z

390

Advanced, High Power, Next Scale, Wave Energy Conversion Device...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Advanced, High Power, Next Scale, Wave Energy Conversion Device Advanced, High Power, Next Scale, Wave Energy Conversion Device Advanced, High Power, Next Scale, Wave Energy...

391

Northeast High-Level Radioactive Waste Transportation Task Force...  

Office of Environmental Management (EM)

Northeast High-Level Radioactive Waste Transportation Task Force Agenda Northeast High-Level Radioactive Waste Transportation Task Force Agenda Northeast High-Level Radioactive...

392

Hole doping in high temperature superconductors using the XANES technique  

E-Print Network (OSTI)

Hole doping in high temperature superconductors using the1994 Thallium-Based High Temperature Superconductors ed A M1994 Thallium-Based High Temperature Superconductors ed A M

Hamdan, Nasser

2012-01-01T23:59:59.000Z

393

High Level Waste Corporate Board Charter | Department of Energy  

Energy Savers (EERE)

High Level Waste Corporate Board Charter High Level Waste Corporate Board Charter High Level Waste Corporate Board Charter More Documents & Publications Corporate Board By-Laws...

394

Design and Evaluation of Novel High Capacity Cathode Materials...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

High Capacity Cathodes Vehicle Technologies Office Merit Review 2014: Design and Evaluation of High Capacity Cathodes Design and Evaluation of Novel High Capacity Cathode Materials...

395

Coal Study Guide - High School | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

High School Coal Study Guide - High School Coal Study Guide - High School More Documents & Publications Coal Study Guide - Middle School Coal Study Guide for Elementary School...

396

High-Level Waste Corporate Board Presentation Archive | Department...  

Office of Environmental Management (EM)

High-Level Waste Corporate Board Presentation Archive High-Level Waste Corporate Board Presentation Archive Archived Documents High-Level Waste Corporate Board, Dr. Ins Triay...

397

Path to High Efficiency Gasoline Engine | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Path to High Efficiency Gasoline Engine Path to High Efficiency Gasoline Engine Path to High Efficiency Gasoline Engine deer10johansson.pdf More Documents & Publications Partially...

398

High Performance and Sustainable Buildings Guidance  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HIGH PERFORMANCE and SUSTAINABLE BUILDINGS GUIDANCE Final (12/1/08) PURPOSE The Interagency Sustainability Working Group (ISWG), as a subcommittee of the Steering Committee established by Executive Order (E.O.) 13423, initiated development of the following guidance to assist agencies in meeting the high performance and sustainable buildings goals of E.O. 13423, section 2(f). 1 E.O. 13423, sec. 2(f) states "In implementing the policy set forth in section 1 of this order, the head of each agency shall: ensure that (i) new construction and major renovations of agency buildings comply with the Guiding Principles for Federal Leadership in High Performance and Sustainable Buildings set forth in the Federal Leadership in High Performance and Sustainable Buildings Memorandum of Understanding (2006)

399

Wausau High School | Open Energy Information  

Open Energy Info (EERE)

Wausau High School Wausau High School Jump to: navigation, search Name Wausau High School Facility Wausau High School Sector Wind energy Facility Type Small Scale Wind Facility Status In Service Location Wausau WI Coordinates 44.97944687°, -89.59666014° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":44.97944687,"lon":-89.59666014,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

400

MPICH | High-Performance Portable MPI  

NLE Websites -- All DOE Office Websites (Extended Search)

MPICH MPICH High-Performance Portable MPI Skip to content Home About MPICH Overview News and Events Collaborators MPI Forum Downloads Releases Release Timeline Pending Tickets Source Changes Documentation Guides Publications MPICH Wiki Hydra Usage Developer Docs Contributor Docs Support FAQs Mailing Lists Bug Reports ABI Compatibility Initiative MPICH is a high performance and widely portable implementation of the Message Passing Interface (MPI) standard. The goals of MPICH are: to provide an MPI implementation that efficiently supports different computation and communication platforms including commodity clusters (desktop systems, shared-memory systems, multicore architectures), high-speed networks and proprietary high-end computing systems (Blue Gene, Cray) to enable cutting-edge research in MPI through an easy-to-extend

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

High Plains Tech Center | Open Energy Information  

Open Energy Info (EERE)

Tech Center Tech Center Jump to: navigation, search Name High Plains Tech Center Facility High Plains Tech Center Sector Wind energy Facility Type Small Scale Wind Facility Status In Service Owner High Plains Tech Center Energy Purchaser High Plains Tech Center Location Woodward OK Coordinates 36.40645133°, -99.4282195° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":36.40645133,"lon":-99.4282195,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

402

high-performance | netl.doe.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

High-Performance Sorbents for Carbon Dioxide Capture from Air Project No.: DE-FE0002438 NETL has partnered with the Georgia Institute of Technology to perform a combined...

403

Highly uniform step and terrace structures on  

E-Print Network (OSTI)

via moderate annealing in disilane. Atomic force microscopy and dark-field low-energy electron temperature of 1,373 K in disilane to avoid some of the complications of high-temperature H2 etching. Indeed

Pohl, Karsten

404

Heat Pump for High School Heat Recovery  

E-Print Network (OSTI)

ICEBO2006, Shenzhen, China Renewable Energy Resources and a Greener Future Vol.VIII-12-1 Heat Pump for High School Bathroom Heat Recovery Kunrong Huang Hanqing Wang Xiangjiang Zhou Associate professor Professor Professor School...

Huang, K.; Wang, H.; Zhou, X.

2006-01-01T23:59:59.000Z

405

Cathode applications to high-current diodes  

SciTech Connect

A principal limitation of pulse length for high electron current density diodes is the gap closure due to plasma propagation. This closure is due to plasma formed on the cathode and anode in the process of explosive field emission created by the required high field stresses of the high current diode. Experimental results of high current density T-F'' cathode and a plasma cathode will be presented. Current densities of greater than 300 A/cm2 were obtained for pulse lengths of 3 {mu}sec. Typical closure velocities were less than 2 mm/usec compared with the typical 2 cm/{mu}sec for explosive emission cathodes. 4 refs., 7 figs.

Pincosy, P.A.; Poulsen, P.; Greenwood, D.

1990-05-31T23:59:59.000Z

406

High Performance Computing Data Center (Fact Sheet)  

SciTech Connect

This two-page fact sheet describes the new High Performance Computing Data Center in the ESIF and talks about some of the capabilities and unique features of the center.

Not Available

2014-08-01T23:59:59.000Z

407

An internal winding high temperature heater  

Science Journals Connector (OSTI)

An internal winding high temperature heater ... General principles are outlined for the construction of compact heaters that are suitable for heating small containers or reaction vessels at constant temperature and up to about 1000 C. ...

A. J. Delbouille; E. G. Derouane

1973-01-01T23:59:59.000Z

408

On Electrical Insulation in High Vacua  

Science Journals Connector (OSTI)

1 January 1878 research-article On Electrical Insulation in High Vacua William Crookes The Royal Society is collaborating with JSTOR to digitize, preserve, and extend access to Proceedings of the Royal Society of London. www.jstor.org

1878-01-01T23:59:59.000Z

409

Noise Absorbing High-Temperature Insulation  

Science Journals Connector (OSTI)

Until recently simple heat shields on the engine, in the engine space or on the subframe of a vehicle had given protection against radiant heat from hot components. Today, complex high-temperature insulation syst...

Peter Cappellucci

2013-07-01T23:59:59.000Z

410

Ultra High Efficiency Electric Motor Generator  

Science Journals Connector (OSTI)

The Ultra High Efficiency Electric Motor Generator is an exciting opportunity to leverage ... in green technology. Marand currently produces this motor/generator at our Moorabbin facility for application ... sola...

Jeff Brown

2012-01-01T23:59:59.000Z

411

The High Shear Rheological Properties of Dispersions  

Science Journals Connector (OSTI)

Extremely high shear rates are applied to pigment dispersions during various scale-up and manufactring processes in several industries. As reported in ... responsible for failures in coating processes. Several additives

V. Ribitsch; J. Pfragner

1995-01-01T23:59:59.000Z

412

Webinar: Highly Efficient Solar Thermochemical Reaction Systems  

Energy.gov (U.S. Department of Energy (DOE))

The Fuel Cell Technologies Office will present a live webinar titled "Highly Efficient Solar Thermochemical Reaction Systems" on Tuesday, January 13, from 12:00 to 1:00 p.m. Eastern Standard Time.

413

R Measurements at High Q^2  

E-Print Network (OSTI)

Previous Measurements of R at high Q^2 are reviewed. Recent R measurement results, including those from the Beijing Spectrometer Experiment, are described. The present status of R measurements and future measurement possiblities are summarized.

F. A. Harris

2001-06-01T23:59:59.000Z

414

High performance computing meets experimental mathematics  

Science Journals Connector (OSTI)

In this paper we describe some novel applications of high performance computing in a discipline now known as "experimental mathematics." The paper reviews some recent published work, and then presents some new results that have not yet appeared in the ...

David H. Bailey; David Broadhurst; Yozo Hida; Xiaoye S. Li; Brandon Thompson

2002-11-01T23:59:59.000Z

415

Testing Competing High-Resolution Precipitation Forecasts  

E-Print Network (OSTI)

Testing Competing High-Resolution Precipitation Forecasts Eric Gilleland Research Prediction Comparison Test D1 D2 D = D1 ­ D2 copyright NCAR 2013 Loss Differential Field #12;Spatial Prediction Comparison Test Introduced by Hering and Genton

Gilleland, Eric

416

High Speed AB-Solar Sail  

E-Print Network (OSTI)

The Solar sail is a large thin film used to collect solar light pressure for moving of space apparatus. Unfortunately, the solar radiation pressure is very small about 9 mkN/sq.m at Earth's orbit. However, the light force significantly increases up to 0.2 - 0.35 N/sq.m near the Sun. The author offers his research on a new revolutionary highly reflective solar sail which flyby (after special maneuver) near Sun and attains velocity up to 400 km/sec and reaching far planets of the Solar system in short time or enable flights out of Solar system. New, highly reflective sail-mirror allows avoiding the strong heating of the solar sail. It may be useful for probes close to the Sun and Mercury and Venus. Key words: AB-solar sail, highly reflective solar sail, high speed propulsion.

Bolonkin, A

2007-01-01T23:59:59.000Z

417

High-Power Laser Beam Cladding  

Science Journals Connector (OSTI)

This paper reports major advances in the understanding, refinement and application of high-power laser beam cladding. The most important relationships between essential laser process variables and clad characteri...

G. J. Bruck

1987-02-01T23:59:59.000Z

418

Engineering of High Energy Cathode Materials  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Engineering of High energy cathode material K. Amine (PI) H. Wu, I. Belharouak, Y.K. Sun Argonne National Laboratory DOE merit review May 14-18 , 2012 This presentation does not...

419

Unfolded aplanats for high-concentration photovoltaics  

Science Journals Connector (OSTI)

The exigencies of high-concentration photovoltaics motivate optics that (1) obviate the need for optical bonds, (2) exhibit maximal optical tolerance, (3) are not damaged at off-axis...

Gordon, Jeffrey M; Feuermann, Daniel; Young, Pete

2008-01-01T23:59:59.000Z

420

Future High-Intensity Proton Accelerators  

E-Print Network (OSTI)

This paper provides an overview of currently planned high-intensity proton accelerators. While for high energies (>10GeV) synchrotrons remain the preferred tools to produce high-intensity beams, recent years have seen an impressive development of linac-based lower-energy (intensity proton drivers for spallation sources, accelerator driven systems (ADS), production of Radioactive Ion Beams (RIB) and various neutrino applications (beta-beam, superbeam, neutrino factory). This paper discusses the optimum machine types for the various beam requirements and uses a range of projects, which are likely to be realised within the coming decade, to illustrate the different approaches to reach high average beam power with the application-specific time structure. Only machines with a beam power above 100kW are considered.

Gerigk, F

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

CONTINUED HIGH PERFORMANCE ENERGY MANAGEMENT COMPANY Fitesa  

NLE Websites -- All DOE Office Websites (Extended Search)

HIGH PERFORMANCE ENERGY MANAGEMENT COMPANY Fitesa UTILITY Clark Public Utilities PROJECT Chiller Upgrade ENERGY SAVINGS 2,524,032 kWhyr PROJECT COST 929,308 INCENTIVE 650,516...

422

Thermodynamics of high-temperature nuclear fuel  

Science Journals Connector (OSTI)

A method for performing a thermodynamic analysis of the high-temperature nuclear fuel using the ASTA computer program is substantiated. Calculations of the chemical composition and pressure of the gas phase of...

I. A. Belov; A. S. Ivanov

423

High Performance Sustainable Building Design RM  

Energy.gov (U.S. Department of Energy (DOE))

The High Performance Sustainable Building Design (HPSBD) Review Module (RM) is a tool that assists the DOE federal project review teams in evaluating the technical sufficiency for projects that may...

424

High Speed AB-Solar Sail  

E-Print Network (OSTI)

The Solar sail is a large thin film used to collect solar light pressure for moving of space apparatus. Unfortunately, the solar radiation pressure is very small about 9 mkN/sq.m at Earth's orbit. However, the light force significantly increases up to 0.2 - 0.35 N/sq.m near the Sun. The author offers his research on a new revolutionary highly reflective solar sail which flyby (after special maneuver) near Sun and attains velocity up to 400 km/sec and reaching far planets of the Solar system in short time or enable flights out of Solar system. New, highly reflective sail-mirror allows avoiding the strong heating of the solar sail. It may be useful for probes close to the Sun and Mercury and Venus. Key words: AB-solar sail, highly reflective solar sail, high speed propulsion.

A. Bolonkin

2007-01-08T23:59:59.000Z

425

High Transparency of Classically Opaque Metallic Films  

Science Journals Connector (OSTI)

It is demonstrated, both theoretically and experimentally, that a classically opaque metallic film can appear highly transparent when the conditions are established for the incident electromagnetic wave to excite coupled surface modes on both sides of the film.

R. Dragila; B. Luther-Davies; S. Vukovic

1985-09-02T23:59:59.000Z

426

Developing high-frequency equities trading models  

E-Print Network (OSTI)

The purpose of this paper is to show evidence that there are opportunities to generate alpha in the high frequency environment of the US equity market, using Principal Component Analysis (PCA hereafter) as a basis for short ...

Infantino, Leandro Rafael

2010-01-01T23:59:59.000Z

427

High Performance Green Building Partnership Consortia | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

are groups from the public and private sectors recognized by the U.S. Department of Energy (DOE) for their commitment to high-performance green buildings. Groups that met...

428

Terrestrial Effects of High Energy Cosmic Rays  

E-Print Network (OSTI)

On geological timescales, the Earth is likely to be exposed to higher than the usual flux of high energy cosmic rays (HECRs) from astrophysical sources such as nearby supernovae, gamma ray bursts or by galactic shocks. ...

Atri, Dimitra

2011-04-26T23:59:59.000Z

429

The evolution of high energy accelerators  

SciTech Connect

In this lecture I would like to trace how high energy particle accelerators have grown from tools used for esoteric small-scale experiments to gigantic projects being hotly debated in Congress as well as in the scientific community.

Courant, E.D.

1989-10-01T23:59:59.000Z

430

High index contrast platform for silicon photonics  

E-Print Network (OSTI)

This thesis focuses on silicon-based high index contrast (HIC) photonics. In addition to mature fiber optics or low index contrast (LIC) platform, which is often referred to as Planar Lightwave Cirrcuit (PLC) or Silica ...

Akiyama, Shoji, 1972-

2004-01-01T23:59:59.000Z

431

AGILA: The Ateneo High Performance Computing System  

E-Print Network (OSTI)

A Beowulf cluster is a low-cost parallel high performance computing system that uses commodity hardware components such as personal computers and standard Ethernet adapters and switches and runs on freely available software such as Linux and LAM-MPI. In this paper the development of the AGILA HPCS, which stands for the Ateneo GigaflopsRange Performance, Linux OS, and Athlon Processors High Performance Computing System, is discussed including its hardware and software configurations and performance evaluation. Keywords High-performance computing, commodity cluster computing, parallel computing, Beowulf-class cluster 1. INTRODUCTION In the Philippines today, computing power in the range of gigaflops is not generally available for use in research and development. Conventional supercomputers or high performance computing systems are very expensive and are beyond the budgets of most university research groups especially in developing countries such as the Philippines. A lower cost option...

Rafael P. Saldaa; Felix P. Muga; II; Jerrold J. Garcia; William Emmanuel S. Yu; S. Yu

2000-01-01T23:59:59.000Z

432

Hitachi High Technologies Corp | Open Energy Information  

Open Energy Info (EERE)

Corp Jump to: navigation, search Name: Hitachi High-Technologies Corp Place: Tokyo, Japan Zip: 105-8717 Sector: Solar Product: Japan-based technology firm that is member of the...

433

NREL: Photovoltaics Research - High-Performance Photovoltaics  

NLE Websites -- All DOE Office Websites (Extended Search)

High-Performance Photovoltaics In an ideal multijunction cell, the top layer produces most of the total power, so the top layer should be of the highest quality. However, in...

434

High-flux solar photon processes  

SciTech Connect

This study was commissioned by the National Renewable Energy Laboratory (NREL) for the purpose of identifying high-flux photoprocesses that would lead to beneficial national and commercial applications. The specific focus on high-flux photoprocesses is based on the recent development by NREL of solar concentrator technology capable of delivering record flux levels. We examined photolytic and photocatalytic chemical processes as well as photothermal processes in the search for processes where concentrated solar flux would offer a unique advantage. 37 refs.

Lorents, D C; Narang, S; Huestis, D C; Mooney, J L; Mill, T; Song, H K; Ventura, S [SRI International, Menlo Park, CA (United States)

1992-06-01T23:59:59.000Z

435

High energy bosons do not propagate  

E-Print Network (OSTI)

We discuss the propagation of bosons (scalars, gauge fields and gravitons) at high energy in the context of the spectral action. Using heat kernel techniques, we find that in the high-momentum limit the quadratic part of the action does not contain positive powers of the derivatives. We interpret this as the fact that the two point Green functions vanish for nearby points, where the proximity scale is given by the inverse of the cutoff.

M. A. Kurkov; Fedele Lizzi; Dmitri Vassilevich

2013-12-08T23:59:59.000Z

436

Data Capture Technique for High Speed Signaling  

DOE Patents (OSTI)

A data capture technique for high speed signaling to allow for optimal sampling of an asynchronous data stream. This technique allows for extremely high data rates and does not require that a clock be sent with the data as is done in source synchronous systems. The present invention also provides a hardware mechanism for automatically adjusting transmission delays for optimal two-bit simultaneous bi-directional (SiBiDi) signaling.

Barrett, Wayne Melvin (Rochester, MN); Chen, Dong (Croton On Hudson, NY); Coteus, Paul William (Yorktwon Heights, NY); Gara, Alan Gene (Mount Kisco, NY); Jackson, Rory (Eastchester, NY); Kopcsay, Gerard Vincent (Yorktown Hieghts, NY); Nathanson, Ben Jesse (Teaneck, NY); Vranas, Paylos Michael (Bedford Hills, NY); Takken, Todd E. (Brewster, NY)

2008-08-26T23:59:59.000Z

437

HIGHLY DISPERSED ALLOY CATHODE CATALYST FOR DURABILITY  

E-Print Network (OSTI)

Understanding high performance materials Pt/C cathode B.S.E. Pt PtCo/C cathode IrB.S.E. Pt Co PtIrCo/C cathodeHIGHLY DISPERSED ALLOY CATHODE CATALYST FOR DURABILITY T. D. Jarvi UTC Power Corporation Electrochemical Area Loss Activity at 900 mVRHE (IR-Free) 0.44 A/mg Pt Specific Activity at 900 m

438

Magnetism in Iron at High Temperatures  

Science Journals Connector (OSTI)

Magnetism in iron at high temperature is investigated by calculating the total electronic band-structure energy for four types of spin arrangements. A slow smooth spatial variation of spin direction costs relatively little energy and the atomic moment m is reduced only ? 10%. More rapid variations have considerably higher energy, which may explain the high degree of short-range order and small ?m observed at T?TC. Other aspects are also discussed.

M. V. You; V. Heine; A. J. Holden; P. J. Lin-Chung

1980-05-12T23:59:59.000Z

439

Nuclear diffractive structure functions at high energies  

E-Print Network (OSTI)

A future high-energy electron-ion collider would explore the non-linear weakly-coupled regime of QCD, and test the Color Glass Condensate (CGC) approach to high-energy scattering. Hard diffraction in deep inelastic scattering off nuclei will provide many fundamental measurements. In this work, the nuclear diffractive structure function F_{2,A}^D is predicted in the CGC framework, and the features of nuclear enhancement and suppression are discussed.

C. Marquet; H. Kowalski; T. Lappi; R. Venugopalan

2008-05-30T23:59:59.000Z

440

Budget projections - 1991 through 1996 for research in high energy physics  

SciTech Connect

This research program in high energy physics is carried out under the general supervision of a committee which is composed of G.W. Brandenburg, G.J. Feldman, M.E. Franklin, R.J. Glauber, K. Kinoshita, F.M. Pipkin, K. Strauch, R. Wilson, and H. Yamamoto. Professor G.J. Feldman currently serves as chair of this committee. Dr. Brandenburg is the Director of the High Energy Physics Laboratory and administers the DOE high energy physics contract. In the fall of 1991 S. Mishra will join this committee. Harvard is planning to make one or two additional senior faculty appointments in experimental high energy physics over the next two years. The principal goals of the work described here are to carry out forefront programs in high energy physics research and to provide first rate educational opportunities for students. The experimental program supported through HEPL is carried out at the major accelerator centers in the world and addresses some of the most important questions in high energy physics. Harvard`s educational efforts are concentrated in graduate education, where they are currently supporting thirteen research students. In addition, undergraduate students work in projects at HEPL during the academic year and over summers. These budget projections cover all of the Harvard based high energy physics experimental activities. The {open_quotes}umbrella{close_quotes} nature of this contract greatly simplifies support of essential central technical and computer services and helps the group to take advantage of new physics opportunities and to respond to unexpected needs. The funding for the operation of the HEPL facility is shared proportionally by the experimental groups. Harvard financially supports this high energy physics research program in many ways.

Not Available

1991-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Budget projections 1990, 1991, and 1992 for research in high energy nuclear physics  

SciTech Connect

Research programs in experimental high energy physics are carried out at Harvard under the general supervision of a departmental faculty committee on high energy physics. The committee members are: G.W. Brandenburg, M. Franklin, S. Geer, R. J. Glauber, K. Kinoshita, F. M. Pipkin, R. F. Schwitters, K. Strauch, M. E. Law, and R. Wilson. Of these individuals, Professors R.J. Glauber, F.M. Pipkin, R.F.Schwitters, K. Strauch, and R. Wilson are the principal investigators with whom a number of junior faculty members and post-doctoral research fellows are associated. Dr. Brandenburg is the Director of the High Energy Physics Laboratory and administers the DOE high energy physics contract. Professor Schwitters is currently on leave of absence as Director of the Superconducting Super Collider project. In the fall of 1990 Professor G. Feldman, who is currently at SLAC, will join the Harvard faculty and become a principal investigator. Harvard is planning to make one or two additional senior faculty appointments in experimental high energy physics over the next two years. The principal goals of the work described here are to carry out forefront programs in high energy physics research and to provide first rate educational opportunities for students. The experimental program supported through HEPL is carried out at the major accelerator centers in the world and addresses some of the most important questions in high energy physics. Harvard`s educational efforts are concentrated in graduate education. These budget projections cover all of the Harvard based high energy physics experimental activities. The {open_quotes}umbrella{close_quotes} nature of this contract greatly simplifies support of essential central technical and computer services and helps the group to take advantage of new physics opportunities and to respond to unexpected needs. The funding for the operation of the HEPL facility is shared equally by the experimental groups.

Not Available

1990-05-01T23:59:59.000Z

442

Research in High Energy Physics at Duke University  

SciTech Connect

This is the Closeout Report for the research grant in experimental elementary particle physics, carried out by the Duke University High Energy Physics (HEP) group. We re- port on physics results and detector development carried out under this grant, focussing on the recent three-year grant period (2010 to 2013). The Duke HEP group consisted of seven faculty members, two senior scientists, #12;ve postdocs and eight graduate students. There were three thrusts of the research program. Measurements at the energy frontier at CDF and ATLAS were used to test aspects of elementary particle theory described by the Stan- dard Model (SM) and to search for new forces and particles beyond those contained within the SM. The neutrino sector was explored using data obtained from a large neutrino detector located in Japan, and R & D was conducted on new experiments to be built in the US. The measurements provided information about neutrino masses and the manner in which neutri- nos change species in particle beams. Two years ago we have started a new research program in rare processes based on the Mu2E experiment at Fermilab. This research is motivated by the search for the #22; ! e transition with unprecedented sensitivity, a transition forbidden in the standard model but allowed in supersymmetric and other models of new physics. The high energy research program used proton and antiproton colliding beams. The experiments were done at the Fermilab Tevatron (proton-antiproton collisions at a center of mass energy of 1.96 TeV) and at the CERN Large Hadron Collider (proton-proton collisions at 7-8 TeV). The neutrino program used data obtained from the Super-Kamiokande detec- tor. This water-#12;lled Cherenkov counter was used to detect and measure the properties of neutrinos produced in cosmic ray showers, and from neutrino beams produced from acceler- ators in Japan. The Mu2E experiment will use a special stopped muon beam to be built at Fermilab.

Kotwal, Ashutosh V. [PI] [PI; Goshaw, Al [Co-PI] [Co-PI; Kruse, Mark [Co-PI] [Co-PI; Oh, Seog [Co-PI] [Co-PI; Scholberg, Kate [Co-PI] [Co-PI; Walter, Chris [Co-PI] [Co-PI

2013-07-29T23:59:59.000Z

443

Research in High Energy Physics at Duke University  

SciTech Connect

This is the Closeout Report for the research grant in experimental elementary particle physics, carried out by the Duke University High Energy Physics (HEP) group. We re- port on physics results and detector development carried out under this grant, focussing on the recent three-year grant period (2010 to 2013). The Duke HEP group consisted of seven faculty members, two senior scientists, five postdocs and eight graduate students. There were three thrusts of the research program. Measurements at the energy frontier at CDF and ATLAS were used to test aspects of elementary particle theory described by the Stan- dard Model (SM) and to search for new forces and particles beyond those contained within the SM. The neutrino sector was explored using data obtained from a large neutrino detector located in Japan, and R & D was conducted on new experiments to be built in the US. The measurements provided information about neutrino masses and the manner in which neutri- nos change species in particle beams. Two years ago we have started a new research program in rare processes based on the Mu2E experiment at Fermilab. This research is motivated by the search for the #22;{mu} {yields} e transition with unprecedented sensitivity, a transition forbidden in the standard model but allowed in supersymmetric and other models of new physics. The high energy research program used proton and antiproton colliding beams. The experiments were done at the Fermilab Tevatron (proton-antiproton collisions at a center of mass energy of 1.96 TeV) and at the CERN Large Hadron Collider (proton-proton collisions at 7-8 TeV). The neutrino program used data obtained from the Super-Kamiokande detector. This water-filled Cherenkov counter was used to detect and measure the properties of neutrinos produced in cosmic ray showers, and from neutrino beams produced from acceler- ators in Japan. The Mu2E experiment will use a special stopped muon beam to be built at Fermilab.

Goshaw, Alfred; Kotwal, Ashutosh; Kruse, Mark; Oh, Seog; Scholberg, Kate; Walter, Chris

2013-07-29T23:59:59.000Z

444

High-k (k=30) amorphous hafnium oxide films from high rate room temperature deposition  

SciTech Connect

Amorphous hafnium oxide (HfO{sub x}) is deposited by sputtering while achieving a very high k{approx}30. Structural characterization suggests that the high k is a consequence of a previously unreported cubiclike short range order in the amorphous HfO{sub x} (cubic k{approx}30). The films also possess a high electrical resistivity of 10{sup 14} {Omega} cm, a breakdown strength of 3 MV cm{sup -1}, and an optical gap of 6.0 eV. Deposition at room temperature and a high deposition rate ({approx}25 nm min{sup -1}) makes these high-k amorphous HfO{sub x} films highly advantageous for plastic electronics and high throughput manufacturing.

Li, Flora M.; Bayer, Bernhard C.; Hofmann, Stephan; Milne, William I.; Flewitt, Andrew J. [Department of Engineering, Electrical Engineering Division, University of Cambridge, JJ Thomson Avenue, Cambridge CB3 0FA (United Kingdom); Dutson, James D.; Wakeham, Steve J.; Thwaites, Mike J. [Plasma Quest Ltd., Unit 1B, Rose Estate, Osborn Way, Hook, Hampshire RG27 9UT (United Kingdom)

2011-06-20T23:59:59.000Z

445

Application of high-throughput computing in bioinformatics  

Science Journals Connector (OSTI)

...Issue New science from high-performance computing organized by Richard Catlow...bioinformatics database|high-performance computing| Application of high-throughput...bioinformatics database; high-performance computing 1. Introduction Organizing...

2002-01-01T23:59:59.000Z

446

Advanced Diagnostics for High Pressure Spray Combustion.  

SciTech Connect

The development of accurate predictive engine simulations requires experimental data to both inform and validate the models, but very limited information is presently available about the chemical structure of high pressure spray flames under engine- relevant conditions. Probing such flames for chemical information using non- intrusive optical methods or intrusive sampling techniques, however, is challenging because of the physical and optical harshness of the environment. This work details two new diagnostics that have been developed and deployed to obtain quantitative species concentrations and soot volume fractions from a high-pressure combusting spray. A high-speed, high-pressure sampling system was developed to extract gaseous species (including soot precursor species) from within the flame for offline analysis by time-of-flight mass spectrometry. A high-speed multi-wavelength optical extinction diagnostic was also developed to quantify transient and quasi-steady soot processes. High-pressure sampling and offline characterization of gas-phase species formed following the pre-burn event was accomplished as well as characterization of gas-phase species present in the lift-off region of a high-pressure n-dodecane spray flame. For the initial samples discussed in this work several species were identified, including polycyclic aromatic hydrocarbons (PAH); however, quantitative mole fractions were not determined. Nevertheless, the diagnostic developed here does have this capability. Quantitative, time-resolved measurements of soot extinction were also accomplished and the novel use of multiple incident wavelengths proved valuable toward characterizing changes in soot optical properties within different regions of the spray flame.

Skeen, Scott A.; Manin, Julien Luc; Pickett, Lyle M.

2014-06-01T23:59:59.000Z

447

Senior DOE Officials in Spain to Participate in World Petroleum...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Senior DOE Officials in Spain to Participate in World Petroleum Congress, July 1, 2008 Senior DOE Officials in Spain to Participate in World Petroleum Congress, July 1, 2008 Senior...

448

Senior Center Network Redesign Under Demand Uncertainty  

E-Print Network (OSTI)

Senior Center Network Redesign Under Demand Uncertainty Osman Y. ¨Ozaltin Department of Industrial of Massachusetts Boston, Boston, MA 02125-3393, USA, michael.johnson@umb.edu Andrew J. Schaefer Department. In response, we propose a two-echelon network of senior centers. We for- mulate a two-stage stochastic

Schaefer, Andrew

449

Page 1 of 6 Senior Honors Project  

E-Print Network (OSTI)

Page 1 of 6 Senior Honors Project Begin thinking about a topic. Gather your thoughts about what ideas. Review examples of past Senior Honors Projects in your field by consulting with an Honors Adviser. Find a Faculty Director to supervise your project. After you have a sense of what you would like to do

Saidak, Filip

450

High Performance Computing in Accelerator Science: Past Successes. Future Challenges  

E-Print Network (OSTI)

High Performance Computing in Accelerator Science: PastAC02- 05CH11231. High Performance Computing in Accelerator

Ryne, R.

2013-01-01T23:59:59.000Z

451

Thermal Strategies for High Efficiency Thermoelectric Power Generation  

Energy.gov (U.S. Department of Energy (DOE))

Developing integrated TE system configurations that can achieve high heat exchange effectiveness and thus, high TE system efficiency

452

Thermal Strategies for High Efficiency Thermoelectric Power Generation...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Thermal Strategies for High Efficiency Thermoelectric Power Generation Thermal Strategies for High Efficiency Thermoelectric Power Generation Developing integrated TE system...

453

High Field Magnet R&D in the USA  

E-Print Network (OSTI)

aI. , "Status of High Temperature Superconductor Magnet R&Dmention High Temperature Superconductor (I-ITS). Though

Gourlay, S.A.

2011-01-01T23:59:59.000Z

454

ULTRA-LOW-ENERGY HIGH-CURRENT ION SOURCE  

E-Print Network (OSTI)

ULTRA-LOW-ENERGY HIGH-CURRENT ION SOURCE (ULEHIIS) Materialenergy, high-intensity ion source (ULEHIIS) for materials

Anders, Andre

2010-01-01T23:59:59.000Z

455

High temperature storage loop : final design report.  

SciTech Connect

A three year plan for thermal energy storage (TES) research was created at Sandia National Laboratories in the spring of 2012. This plan included a strategic goal of providing test capability for Sandia and for the nation in which to evaluate high temperature storage (>650%C2%B0C) technology. The plan was to scope, design, and build a flow loop that would be compatible with a multitude of high temperature heat transfer/storage fluids. The High Temperature Storage Loop (HTSL) would be reconfigurable so that it was useful for not only storage testing, but also for high temperature receiver testing and high efficiency power cycle testing as well. In that way, HTSL was part of a much larger strategy for Sandia to provide a research and testing platform that would be integral for the evaluation of individual technologies funded under the SunShot program. DOE's SunShot program seeks to reduce the price of solar technologies to 6/kWhr to be cost competitive with carbon-based fuels. The HTSL project sought to provide evaluation capability for these SunShot supported technologies. This report includes the scoping, design, and budgetary costing aspects of this effort

Gill, David Dennis; Kolb, William J.

2013-07-01T23:59:59.000Z

456

Budget projections 1988, 1989, and 1990 for research in high energy nuclear physics  

SciTech Connect

Research programs in experimental high energy physics are carried out at Harvard under the general supervision of a departmental faculty committee on high energy physics. Professor R.F. Schwitters is currently chairman of this committee. The committee members are: G.W. Brandenburg, S. Geer, R.J. Glauber, K. Kinoshita, R. Nickerson, F.M. Pipkin, J. Rohlf, C. Rubbia, R.F. Schwitters, M. Shapiro, K. Strauch, R. Vanelli, and R. Wilson. Of these individuals, Professors R.J. Glauber, F.M. Pipkin, C. Rubbia, R.F. Schwitters, K. Strauch, and R. Wilson are the principal investigators with whom a number of junior faculty members and post-doctoral research fellows are associated. Dr. Brandenburg (Associate Director, High Energy Physics Laboratory) administers the High Energy Physics Laboratory and is in charge of the Computer Facility. Professor Rubbia is currently on leave of absence and will leave Harvard on December 31, 1988 to become the Director General of CERN. A reduced UA1 effort will remain at Harvard after Professor Rubbia`s departure. Harvard is planning to make one or two senior faculty appointments in experimental high energy physics sometime in 1988-89. The principal goals of the work described here are to carry out forefront programs in high energy physics research and to provide first rate educational opportunities for students. The experimental program supported through HEPL is carried out at the major accelerator centers in the world and addresses some of the most important questions in high energy physics. Harvard`s educational efforts are concentrated in graduate education, where they are currently supporting 15 research students. In addition, undergraduate students work in projects at HEPL during the academic year and over summers. Many of these students have gone on to graduate school studying physics at Harvard and elsewhere.

Not Available

1988-04-01T23:59:59.000Z

457

Budget projections 1989, 1990, and 1991 for research in high energy nuclear physics  

SciTech Connect

Research programs in experimental high energy physics are carried out at Harvard under the general supervision of a departmental faculty committee on high energy physics. The committee members are: G.W. Brandenburg, S. Geer, R.J. Glauber, K. Kinoshita, R. Nickerson, F.M. Pipkin, R.F. Schwitters, M. Shapiro, K. Strauch, R. Vanelli, and R. Wilson. Of these individuals, Professors R.J. Glauber, F.M. Pipkin, R.F. Schwitters, K. Strauch, and R. Wilson are the principal investigators with whom a number of junior faculty members and post-doctoral research fellows are associated. Dr. Brandenburg is the Director of the High Energy Physics Laboratory and administers the DOE high energy physics contract. Professor Schwitters is currently on leave of absence as Director of the Superconducting Super Collider project. In the fall of 1990 Professor G. Feldman, who is currently at SLAC, will join the Harvard faculty and become a principal investigator. Harvard is planning to make one or two additional senior faculty appointments in experimental high energy physics over the next two years. The principal goals of the work described here are to carry out forefront programs in high energy physics research and to provide first rate educational opportunities for students. The experimental program supported through HEPL is carried out at the major accelerator centers in the world. Harvard`s educational efforts are concentrated in graduate education, where they are currently supporting 15 research students. These budget projections cover all of the Harvard based high energy physics experimental activities. The {open_quotes}umbrella{close_quotes} nature of this contract greatly simplifies support of essential central technical and computer services and helps the group to take advantage of new physics opportunities and to respond to unexpected needs. The funding for the operation of the HEPL facility is shared equally by the experimental groups.

Not Available

1989-05-01T23:59:59.000Z

458

Senior Advisor Huizenga's Written Statement before the House...  

Office of Environmental Management (EM)

Senior Advisor Huizenga's Written Statement before the House Energy and Water Development Subcommittee on Appropriations (March 21, 2012) Senior Advisor Huizenga's Written...

459

Assistant Secretary Cathy Zoi and Senior Advisor Matt Rogers...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Assistant Secretary Cathy Zoi and Senior Advisor Matt Rogers to Participate in Platts Energy Reporter Roundtable Assistant Secretary Cathy Zoi and Senior Advisor Matt Rogers to...

460

Electric Vehicle (EV) Carsharing in A Senior Adult Community  

E-Print Network (OSTI)

Electric Vehicle (EV) Carsharing in A Senior Adult Community Susan with Nissan Motor Co. to study feasibility of EV carsharing program in senior adult

Kammen, Daniel M.

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Senior Technical Safety Manager Qualification Program Self-Assessment...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Senior Technical Safety Manager Qualification Program Self-Assessment - Chief of Nuclear Safety Senior Technical Safety Manager Qualification Program Self-Assessment - Chief of...

462

High Temperature Cements | Open Energy Information  

Open Energy Info (EERE)

High Temperature Cements High Temperature Cements Jump to: navigation, search Geothermal ARRA Funded Projects for High Temperature Cements Loading map... {"format":"googlemaps3","type":"ROADMAP","types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"limit":200,"offset":0,"link":"all","sort":[""],"order":[],"headers":"show","mainlabel":"","intro":"","outro":"","searchlabel":"\u2026 further results","default":"","geoservice":"google","zoom":false,"width":"600px","height":"350px","centre":false,"layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","icon":"","visitedicon":"","forceshow":true,"showtitle":true,"hidenamespace":false,"template":false,"title":"","label":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"locations":[{"text":"

463

High Performance Computing Data Center Metering Protocol  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

High Performance High Performance Computing Data Center Metering Protocol Prepared for: U.S. Department of Energy Office of Energy Efficiency and Renewable Energy Federal Energy Management Program Prepared by: Thomas Wenning Michael MacDonald Oak Ridge National Laboratory September 2010 ii Introduction Data centers in general are continually using more compact and energy intensive central processing units, but the total number and size of data centers continues to increase to meet progressive computing requirements. In addition, efforts are underway to consolidate smaller data centers across the country. This consolidation is resulting in a growth of high-performance computing facilities (i.e. - supercomputers) which consume large amounts of energy to support the numerically intensive

464

High Performance Sustainable Building Design RM  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

High Performance Sustainable High Performance Sustainable Building Design Review Module March 2010 CD-0 O High 0 This Re Les OFFICE OF h Perform CD-1 eview Module ssons learned f F ENVIRON Standard R mance Su Revi Critical D CD-2 M has been pilot from the pilot h NMENTAL Review Plan ustainabl iew Module Decision (CD C March 2010 ted at the SRS have been incor L MANAGE n (SRP) le Buildin e D) Applicabili D-3 SWPF and MO rporated in Rev EMENT ng Design ity CD-4 OX FFF projec view Module n Post Ope cts. eration Standard Review Plan, 2 nd Edition, March 2010 i FOREWORD The Standard Review Plan (SRP) 1 provides a consistent, predictable corporate review framework to ensure that issues and risks that could challenge the success of Office of Environmental Management (EM) projects are identified early and addressed proactively. The

465

MHL High Speed Cavitation | Open Energy Information  

Open Energy Info (EERE)

High Speed Cavitation High Speed Cavitation Jump to: navigation, search Basic Specifications Facility Name MHL High Speed Cavitation Overseeing Organization University of Michigan Hydrodynamics Hydrodynamic Testing Facility Type Channel Length(m) 0.8 Beam(m) 0.2 Depth(m) 0.2 Cost(per day) $2000(+ Labor/Materials) Towing Capabilities Towing Capabilities Yes Maximum Velocity(m/s) 25.9 Wavemaking Capabilities Wavemaking Capabilities None Channel/Tunnel/Flume Channel/Tunnel/Flume Yes Velocity(m/s) 25.9 Recirculating No Wind Capabilities Wind Capabilities None Control and Data Acquisition Description Custom Data Acquisition System using National Instruments hardware; system compatible with Planing Hull and Floating Beam Dynamometers Number of channels 16 Bandwidth(kHz) 20 Cameras Yes

466

High Speed Particle Image Velocimetry Overview  

NLE Websites -- All DOE Office Websites (Extended Search)

Speed Particle Image Velocimetry Speed Particle Image Velocimetry Overview The Department of Energy's National Energy Technology Laboratory is seeking licensing partners interested in implementing U.S. Non- provisional Patent Application 12/765,317 entitled "Method of Particle Trajectory Recognition in Particle Flows of High Particle Concentration Using a Candidate Trajectory Tree Process with Variable Search Areas." This patent application discloses a novel method to simultaneously track the motion of high numbers of object images under extreme, high concen- tration conditions. Although the software is designed to simultaneously track large numbers of particle images in flow fields, it can track any type of object whose locations are available at consecutive time increments (e.g.,

467

High-Performance Mass Spectrometry Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

HPMSF Overview HPMSF Overview Section 2-4-1 High-Performance Mass Spectrometry Facility The High-Performance Mass Spectrometry Facility (HPMSF) provides state-of-the-art mass spectrometry (MS) and separations instrumentation that has been refined for leading-edge analysis of biological problems with a primary emphasis on proteomics. Challenging research in proteomics, cell signaling, cellular molecular machines, and high-molecular weight systems receive the highest priority for access to the facility. Current research activities in the HPMSF include proteomic analyses of whole cell lysates, analyses of organic macro-molecules and protein complexes, quantification using isotopically labeled growth media, targeted proteomics analyses of subcellular fractions, and nucleic acid analysis of

468

High-Energy-Density Plasmas, Fluids  

NLE Websites -- All DOE Office Websites (Extended Search)

High-Energy-Density Plasmas, Fluids High-Energy-Density Plasmas, Fluids /science-innovation/_assets/images/icon-science.jpg High-Energy-Density Plasmas, Fluids National security depends on science and technology. The United States relies on Los Alamos National Laboratory for the best of both. No place on Earth pursues a broader array of world-class scientific endeavors. TRIDENT target chamber Sasi Palaniyappan, right, and Rahul Shah left inside a target chamber where the TRIDENT short pulse laser is aimed at a very thin diamond- foil target, a fraction of a micrometer thick. The laser delivers a power on target of 150 Terawatts focused into a 7 micrometer spot, yielding laser brilliance over 100 times more intense than needed to make the target electrons fully relativistic. These experiments test novel methods of producing intense

469

High Bandwidth Differential Amplifier for Shock Experiments  

SciTech Connect

We developed a high bandwidth differential amplifier for gas gun shock experiments/applications. The circuit has a bandwidth > 1 GHz, and is capable of measuring signals of ?1.5 V with a common mode rejection of 250 V. Conductivity measurements of gas gun targets are measured by flowing high currents through the targets. The voltage is measured across the target using a technique similar to a four-point probe. Because of the design of the current source and load, the target voltage is approximately 250 V relative to ground. Since the expected voltage change in the target is < 1 V, the differential amplifier must have a large common mode rejection. High pass filters suppress internal ringing of operational amplifiers. Results of bench tests are shown.

Ross, P. W., Tran, V., Chau, R.

2012-04-30T23:59:59.000Z

470

Proposal for a High Energy Nuclear Database  

E-Print Network (OSTI)

We propose to develop a high-energy heavy-ion experimental database and make it accessible to the scientific community through an on-line interface. This database will be searchable and cross-indexed with relevant publications, including published detector descriptions. Since this database will be a community resource, it requires the high-energy nuclear physics community's financial and manpower support. This database should eventually contain all published data from Bevalac, AGS and SPS to RHIC and LHC energies, proton-proton to nucleus-nucleus collisions as well as other relevant systems, and all measured observables. Such a database would have tremendous scientific payoff as it makes systematic studies easier and allows simpler benchmarking of theoretical models to a broad range of old and new experiments. Furthermore, there is a growing need for compilations of high-energy nuclear data for applications including stockpile stewardship, technology development for inertial confinement fusion and target and ...

Vogt, D A B R

2005-01-01T23:59:59.000Z

471

Future high energy colliders symposium. Summary report  

SciTech Connect

A `Future High Energy Colliders` Symposium was held October 21-25, 1996 at the Institute for Theoretical Physics (ITP) in Santa Barbara. This was one of the 3 symposia hosted by the ITP and supported by its sponsor, the National Science Foundation, as part of a 5 month program on `New Ideas for Particle Accelerators`. The long term program and symposia were organized and coordinated by Dr. Zohreh Parsa of Brookhaven National Laboratory/ITP. The purpose of the symposium was to discuss the future direction of high energy physics by bringing together leaders from the theoretical, experimental and accelerator physics communities. Their talks provided personal perspectives on the physics objectives and the technology demands of future high energy colliders. Collectively, they formed a vision for where the field should be heading and how it might best reach its objectives.

Parsa, Z. [Univ. of California, Santa Barbara, CA (United States). Institute for Theoretical Physics]|[Brookhaven National Lab., Upton, CA (United States)

1996-12-31T23:59:59.000Z

472

Nonlocality Distillation for High-Dimensional System  

E-Print Network (OSTI)

The intriguing and powerful capability of nonlocality in communication field ignites the research of the nonlocality distillation. The first protocol presented in Ref[Phys. Rev. Lett. 102, 120401] shows that the nonlocality of bipartite binary-input and binary-output nonsignaling correlated boxes could be amplified by 'wiring' two copies of weaker-nonlocality boxes. Several optimized distillation protocols were presented later for bipartite binary-input and binary-output nonsignaling correlated boxes. In this paper, we focus on the bipartite binary-input and multi-nary-output nonsignaling correlated boxes---high-dimensional boxes, and design comparators-based protocols to achieve the distillation of high-dimensional nonlocality. The results show that the high-dimensional nonlocality can be distilled in different ways, and we find that the efficiencies of the protocols are influenced not only by the wirings but also by the classes the initial nonlocality boxes belongs to. Here, the initial nonlcalities may hav...

Pan, Guo-Zhu; Chen, Zheng-Gen; Yang, Ming; Cao, Zhuo-Liang

2012-01-01T23:59:59.000Z

473

High Temperature Membrane & Advanced Cathode Catalyst Development  

SciTech Connect

Current project consisted of three main phases and eighteen milestones. Short description of each phase is given below. Table 1 lists program milestones. Phase 1--High Temperature Membrane and Advanced Catalyst Development. New polymers and advanced cathode catalysts were synthesized. The membranes and the catalysts were characterized and compared against specifications that are based on DOE program requirements. The best-in-class membranes and catalysts were downselected for phase 2. Phase 2--Catalyst Coated Membrane (CCM) Fabrication and Testing. Laboratory scale catalyst coated membranes (CCMs) were fabricated and tested using the down-selected membranes and catalysts. The catalysts and high temperature membrane CCMs were tested and optimized. Phase 3--Multi-cell stack fabrication. Full-size CCMs with the down-selected and optimized high temperature membrane and catalyst were fabricated. The catalyst membrane assemblies were tested in full size cells and multi-cell stack.

Protsailo, Lesia

2006-04-20T23:59:59.000Z

474

High density effective theory on the lattice  

E-Print Network (OSTI)

Long-range interactions in finite density QCD necessitate a non-perturbative approach in order to reliably map out the key features and spectrum of the QCD phase diagram. However, the complex nature of the fermion determinant in this sector prohibits the use of established Monte Carlo techniques that utilize importance sampling. Whilst significant progress has been made in the low density, high temperature region, this remains a considerable challenge at mid to high density. At large chemical potential, QCD can be approximated using high density effective theory which is free from the sign problem at leading order. We investigate the implementation of this theory on the lattice in conjunction with existing re-weighting techniques.

A. Dougall

2007-10-08T23:59:59.000Z

475

Research towards high speed extrusion freeforming  

Science Journals Connector (OSTI)

Additive Manufacturing (AM) methods are currently utilised for the manufacture of prototypes and low volume, high cost parts. This is because in most cases the high material costs and low volumetric deposition rates of AM parts result in higher per part cost than traditional manufacturing methods. This paper brings together recent research aimed at improving the economics of AM, in particular Extrusion Freeforming (EF). A new class of machine is described called High Speed Additive Manufacturing (HSAM) in which software, hardware and materials advances are aggregated. HSAM could be cost competitive with injection moulding for medium sized medium quantity parts. A general outline for a HSAM machine and supply chain is provided along with future required research.

Hadley Brooks; Mihaela E. Lupeanu; Barry Piorkowski

2013-01-01T23:59:59.000Z

476

A Software Architecture for High Level Applications  

SciTech Connect

A modular software platform for high level applications is under development at the National Synchrotron Light Source II project. This platform is based on client-server architecture, and the components of high level applications on this platform will be modular and distributed, and therefore reusable. An online model server is indispensable for model based control. Different accelerator facilities have different requirements for the online simulation. To supply various accelerator simulators, a set of narrow and general application programming interfaces is developed based on Tracy-3 and Elegant. This paper describes the system architecture for the modular high level applications, the design of narrow and general application programming interface for an online model server, and the prototype of online model server.

Shen,G.

2009-05-04T23:59:59.000Z

477

The design of stable high nitrogen systems  

SciTech Connect

A general strategy for the design of high nitrogen systems with an adequate degree of stability has been elaborated. The design of nitro compounds in which terminal nitro groups are bonded to the chain of several heteroatoms is a specific case within the strategy. In the process of working out the strategy a number of new high nitrogen systems (dinitrazenic acid or dinitroamide HN{sub 3}O{sub 4} and its salts, nitrodiazene oxides RN{sub 3}O{sub 3} and tetrazine dioxides) were discovered. A new of new types of nitro compounds (bicyclo nitro-bis-hydroxylamine, nitrohydrazine, nitrohydroxylamine, sulfo-N-nitroimide and bis-N-nitroimide) were synthesized. This study opens new prospects in the field of the synthesis of high energy materials.

Tartakovsky, V.A. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Inst. of Organic Chemistry

1996-07-01T23:59:59.000Z

478

Sunshot Initiative High Penetration Solar Portal  

DOE Data Explorer (OSTI)

The DOE SunShot Initiative is a collaborative national initiative to make solar energy cost-competitive with other forms of energy by the end of the decade. Reducing the installed cost of solar energy systems by about 75% will drive widespread large-scale adoption of this renewable energy and restore U.S. leadership in the global clean energy race. The High Penetration Solar Portal was created as a resource to aggregate the most relevant and timely information related to high penetration solar scenarios and integrating solar into the grid. The site is designed so that utilities, grant awardees, regulators, researchers, and other solar professionals can easily share data, case studies, lessons learned, and demonstration project findings. [from https://solarhighpen.energy.gov/about_the_high_penetration_solar_portal

479

Manufacturing Barriers to High Temperature PEM Commercialization  

NLE Websites -- All DOE Office Websites (Extended Search)

9/2011 9/2011 1 BASF Fuel Cell, Inc. Manufacturing Barriers to high temperature PEM commercialization 39 Veronica Ave Somerset , NJ 08873 Tel : (732) 545-5100 9/9/2011 2 Background on BASF Fuel Cell  BASF Fuel Cell was established in 2007, formerly PEMEAS Fuel Cells (including E-TEK)  Product line is high temperature MEAs (Celtec ® P made from PBI-phosphoric acid)  Dedicated a new advanced pilot manufacturing facility in Somerset NJ May 2009. Ribbon-cutting hosted by Dr. Kreimeyer (BASF BoD, right) and attended by various US pubic officials including former NJ Governor Jon Corzine (left) 9/9/2011 3 Multi-layer product of membrane (polybenzimidazole and phosphoric acid), gas diffusion material and catalysts Unique characteristics:  High operating temperature

480

Energy management options for high speed trains  

SciTech Connect

The efficient operation of trains which undergo large changes in energy as they fulfill their operational function requires recapture of the kinetic energy of a high speed train or the potential energy of a train in mountainous terrain. This paper is a description of the various storage options available in the railroad environment and their relative merits. The economic, environmental, and safety issues are discussed. The options discussed include: the physical means of storing energy, the location on board the train or on fixed ground, and the relation of energy storage to the nature of the engine used as a prime mover. It is argued that, in the absence of a fully electric, power supply connected to a utility grid, the gas turbine engine is the best propulsion system to meet the propulsion needs of trains requiring high power and efficiency because its high power to weight ratio enables the use of energy storage.

Decher, R. [Univ. of Washington, Seattle, WA (United States). Dept. of Aeronautics and Astronautics

1995-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "high senior high" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Argonne CNM Highlight: High density, high-aspect-ratio precision polyimide  

NLE Websites -- All DOE Office Websites (Extended Search)

High density, high-aspect-ratio precision polyimide nanofilters High density, high-aspect-ratio precision polyimide nanofilters Polyimide Nanofilter SEM of a polyimide film with holes ~250 nm in diameter and ~10 µm deep. The cross-sectional cut of the channels in the front are made visible by focused ion-beam milling. Collaborative users from Creatv MicroTech, Inc. and Los Alamos National Laboratory, working with CNM's Nanofabrication & Devices Group, have demonstrated a novel fabrication process that produces high-porosity polymer nanofilters with smooth, uniform. and straight pores and high aspect ratios. Nanofilters have a wide range of applications for various size-exclusion-based separations in bioseparation and nanomedicine, such as laboratory assays, removing bacteria and viruses, drug delivery devices,

482

Utilization of Wind Energy at High Altitude  

E-Print Network (OSTI)

Ground based, wind energy extraction systems have reached their maximum capability. The limitations of current designs are: wind instability, high cost of installations, and small power output of a single unit. The wind energy industry needs of revolutionary ideas to increase the capabilities of wind installations. This article suggests a revolutionary innovation which produces a dramatic increase in power per unit and is independent of prevailing weather and at a lower cost per unit of energy extracted. The main innovation consists of large free-flying air rotors positioned at high altitude for power and air stream stability, and an energy cable transmission system between the air rotor and a ground based electric generator. The air rotor system flies at high altitude up to 14 km. A stability and control is provided and systems enable the changing of altitude. This article includes six examples having a high unit power output (up to 100 MW). The proposed examples provide the following main advantages: 1. Large power production capacity per unit - up to 5,000-10,000 times more than conventional ground-based rotor designs; 2. The rotor operates at high altitude of 1-14 km, where the wind flow is strong and steady; 3. Installation cost per unit energy is low. 4. The installation is environmentally friendly (no propeller noise). -- * Presented in International Energy Conversion Engineering Conference at Providence., RI, Aug. 16-19. 2004. AIAA-2004-5705. USA. Keyword: wind energy, cable energy transmission, utilization of wind energy at high altitude, air rotor, windmills, Bolonkin.

Alexander Bolonkin

2007-01-10T23:59:59.000Z

483

Project of Rotating Carbon High-Power Neutron Target. Research of Graphite Properties for Production of High Intensity Neutron Source  

E-Print Network (OSTI)

Project of Rotating Carbon High-Power Neutron Target. Research of Graphite Properties for Production of High Intensity Neutron Source

Gubin, K V; Bak, P A; Kot, N K; Logatchev, P V

2001-01-01T23:59:59.000Z

484

JC3 High Impact Assessment Bulletins  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

high-impact-assessment-bulletins high-impact-assessment-bulletins Office of the Chief Information Officer 1000 Independence Ave., SW Washington, DC 202-586-0166 en V-215: NetworkMiner Directory Traversal and Insecure Library Loading Vulnerabilities http://energy.gov/cio/articles/v-215-networkminer-directory-traversal-and-insecure-library-loading-vulnerabilities V-215: NetworkMiner Directory Traversal and Insecure Library Loading Vulnerabilities

485

Techniques for Reducing High Risk Contracting Approaches  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reducing High Reducing High Risk Contracting Approaches Topics for Discussion Presidential Direction March 4, 2009 * Focus on transparency * Increase competition - It is the policy of the Federal Government that executive agencies shall not engage in noncompetitive contracts except in those circumstances where their use can be fully justified and where appropriate safeguards have been put in place to protect the taxpayer. * Improve competitive environment for the life of multiple award contracts * Reduce risk of cost growth/overcharging * Office of Management and Budget (OMB) Guidance to improve Government Acquisition , 29 July 2009 (implements President's direction) Why the Emphasis? * Reports by agency Inspectors General, the

486

Polyelectrolyte Materials for High Temperature Fuel Cells  

NLE Websites -- All DOE Office Websites (Extended Search)

Polyelectrolyte Materials for High Polyelectrolyte Materials for High 3M (3M) Temperature Fuel Cells John B. Kerr Lawrence Berkeley National Laboratory (LBNL) Collaborators: Los Alamos National Laboratory (LANL). February 13, 2007 This presentation does not contain any proprietary or confidential information Team Members: Nitash Blasara, Rachel Segalman, Adam Weber (LBNL). Bryan Pivovar, James Boncella (LANL) Steve Hamrock Objectives * Investigate the use of solid polyelectrolyte proton conductors that do not require the presence of water. * Prepare solid electrolytes where only the proton moves. - Measure conductivity, mechanical/thermal properties of Nafion® and other polyelectrolytes doped with imidazoles. Compare with water doped materials. - Covalently attach imidazoles to side chains of ionomers with

487

Viscosity of liquid Fe at high pressure  

Science Journals Connector (OSTI)

Synchrotron x-ray radiography has been used to measure the viscosity of pure liquid Fe at high pressure and temperature in a large volume press. A probe sphere rising through liquid Fe at high pressure and temperature is imaged, in situ, allowing for the derivation of sample viscosity through a modified form of Stokes equation. The effect of pressure on viscosity is fit by the semi empirical framework for transport coefficients in liquid metals, providing experimental verification of constant viscosity at the pressure-dependent melting temperature of liquid Fe where no change in liquid structure occurs.

Michael D. Rutter; Richard A. Secco; Hongjian Liu; Takeyuki Uchida; Mark L. Rivers; Stephen R. Sutton; Yanbin Wang

2002-08-14T23:59:59.000Z

488

Insensitive fuze train for high explosives  

DOE Patents (OSTI)

A generic insensitive fuze train to initiate insensitive high explosives, such as PBXW-124 is described. The insensitive fuze train uses a slapper foil to initiate sub-gram quantities of an explosive, such as HNS-IV or PETN. This small amount of explosive drives a larger metal slapper onto a booster charge of an insensitive explosive, such as UF-TATB. The booster charge initiates a larger charge of an explosive, such as LX-17, which in turn, initiates the insensitive high explosive, such as PBXW-124. 3 figures.

Cutting, J.L.; Lee, R.S.; Von Holle, W.G.

1994-01-04T23:59:59.000Z

489

Insensitive fuze train for high explosives  

DOE Patents (OSTI)

A generic insensitive fuze train to initiate insensitive high explosives, such as PBXW-124. The insensitive fuze train uses a slapper foil to initiate sub-gram quantities of an explosive, such as HNS-IV or PETN. This small amount of explosive drives a larger metal slapper onto a booster charge of an insensitive explosive, such as UF-TATB. The booster charge initiates a larger charge of an explosive, such as LX-17, which in turn, initiates the insensitive high explosive, such as PBXW-124.

Cutting, Jack L. (Livermore, CA); Lee, Ronald S. (Livermore, CA); Von Holle, William G. (Livermore, CA)

1994-01-01T23:59:59.000Z

490

Method for producing high dielectric strength microvalves  

DOE Patents (OSTI)

A microvalve having a cast-in-place and lithographically shaped mobile, polymer monolith for fluid flow control in microfluidic devices and method of manufacture. The microvalve contains a porous fluorinated polymer monolithic element whose pores are filled with an electrically insulating, high dielectric strength fluid, typically a perfluorinated liquid. This combination provides a microvalve that combines high dielectric strength with extremely low electrical conductivity. These microvalves have been shown to have resistivities of at least 100 G.OMEGA. and are compatible with solvents such as water at a pH between 2.7 and 9.0, 1-1 propanol, acetonitrile, and acetone.

Kirby, Brian J. (San Francisco, CA); Reichmuth, David S. (Oakland, CA); Shepodd, Timothy J. (Livermore, CA)

2006-04-04T23:59:59.000Z

491

Aerodynamic Focusing Of High-Density Aerosols  

SciTech Connect

High-density micron-sized particle aerosols might form the basis for a number of applications in which a material target with a particular shape might be quickly ionized to form a cylindrical or sheet shaped plasma. A simple experimental device was built in order to study the properties of high-density aerosol focusing for 1#22; m silica spheres. Preliminary results recover previous findings on aerodynamic focusing at low densities. At higher densities, it is demonstrated that the focusing properties change in a way which is consistent with a density dependent Stokes number.

Ruiz, D. E.; Fisch, Nathaniel

2014-02-24T23:59:59.000Z

492

High-energy cosmic ray interactions  

SciTech Connect

Research into hadronic interactions and high-energy cosmic rays are closely related. On one hand--due to the indirect observation of cosmic rays through air showers--the understanding of hadronic multiparticle production is needed for deriving the flux and composition of cosmic rays at high energy. On the other hand the highest energy particles from the universe allow us to study the characteristics of hadronic interactions at energies far beyond the reach of terrestrial accelerators. This is the summary of three introductory lectures on our current understanding of hadronic interactions of cosmic rays.

Engel, Ralph [Forschungszentrum Karlsruhe, P.O. Box 3640, 76021 Karlsruhe (Germany); Orellana, Mariana [Instituto Argentino de Radioastronomia (IAR), CCT La Plata (CONICET), C.C.5, 1894 Villa Elisa, Buenos Aires (Argentina); Facultad de Ciencias Astronomicas y Geofisicas, Universidad Nacional de La Plata, Paseo del Bosque, 1900 La Plata (Argentina); Reynoso, Matias M. [Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Mar del Plata, Funes 3350, (7600) Mar del Plata (Argentina); Instituto de Investigaciones Fisicas de Mar del Plata, (UNMdP-CONICET) (Argentina); Vila, Gabriela S. [Instituto Argentino de Radioastronomia (IAR), CCT La Plata (CONICET), C.C.5, 1894 Villa Elisa, Buenos Aires (Argentina)

2009-04-30T23:59:59.000Z

493

Reversible chemisorption on highly dispersed Ru catalysts  

SciTech Connect

Hydrogen and carbon monoxide adsorptions have been studied by static gas volumetric measurement on a range of highly dispersed Y-zeolite-supported ruthenium catalysts prepared by ion exchange. At ambient temperature, the absorption isotherms indicated two distinct types of adsorption - reversible (composed of both physisorption and weak chemisorption) and irreversible (strongly chemisorbed). The catalysts were highly dispersed and had average particle diameters ranging from 0.9 to 1.6 nm. Reversible hydrogen chemisorption was found to be a function of average particle diameter and dispersion. On the other hand, reversible carbon monoxide chemisorption seemed to be mainly due to interaction with the support.

Yang, C.H.; Goodwin, J.G. Jr.

1982-11-01T23:59:59.000Z

494

Nitrogen Deposition in the Southern High Plains  

E-Print Network (OSTI)

Nitrogen Deposition in the Southern High Plains Nitrogen is necessary for life on earth, but getting too much of it can be harmful. Recent research in delicate alpine watersheds of the western United States has suggested that the amount... Nitrogen Deposition in the Southern High Plains Conservation of mass: It?s not just a good idea, it?s the law Nitrogen, along with every other element in nature, obeys certain physical laws. The first of those laws, the law of conservation of mass...

Upadhyay, Jeetendra; Auvermann, Brent W.; Bush, K. Jack; Mukhtar, Saqib

2008-02-11T23:59:59.000Z

495

3 - High temperature superconductor (HTS) cables  

Science Journals Connector (OSTI)

Abstract: Many superconductor applications such as rotating machinery, transformers and magnets with low inductance require high current cables with low AC losses. This chapter gives an overview on cabling techniques for the high temperature superconductors (HTS) BSCCO (2212), BSCCO (2223) and (RE)BCO. A short review is given of the basic properties of HTS wires and tapes and the basic requirements of HTS cables for different applications. Cabling concepts for the different HTS materials are presented, and current performance and AC loss behaviour are discussed. After a short description of remaining challenges and future trends, cabling techniques are summarized.

S.I. Schlachter; W. Goldacker

2012-01-01T23:59:59.000Z

496

Application of high temperature superconductors for fusion  

Science Journals Connector (OSTI)

The use of High Temperature Superconductor (HTS) materials in future fusion machines can increase the efficiency drastically. For ITER, W7-X and JT-60SA the economic benefit of HTS current leads was recognized after a 70kA HTS current lead demonstrator was designed, fabricated and successfully tested by Karlsruhe Institute of Technology (KIT, which is a merge of former Forschungszentrum Karlsruhe and University of Karlsruhe). For ITER, the Chinese Domestic Agency will provide the current leads as a part of the superconducting feeder system. KIT is in charge of design, construction and test of HTS current leads for W7-X and JT-60SA. For W7-X 14 current leads with a maximum current of 18.2kA are required that are oriented with the room temperature end at the bottom. JT60-SA will need 26 current leads (20 leads @ 20kA and 6 leads @ 25.7kA) which are mounted in vertical, normal position. These current leads are based on BiSCCO HTS superconductors, demonstrating that HTS material is now state of the art for highly efficient current leads. With respect to future fusion reactors, it would be very promising to use HTS material not only in current leads but also in coils. This would allow a large increase of efficiency if the coils could be operated at temperatures ?65K. With such a high temperature it would be possible to omit the radiation shield of the coils, resulting in a less complex cryostat and a size reduction of the machine. In addition less refrigeration power is needed saving investment and operating costs. However, to come to an HTS fusion coil it is necessary to develop low ac loss HTS cables for currents well above 20kA at high fields well above 10T. The high field rules BiSCCO superconductors out at temperatures above 50K, but RE-123 superconductors are promising. The development of a high current, high field RE-123 HTS fusion cable will not be targeted outside fusion community and has to be in the frame of a long term development programme for DEMO. KIT has already demonstrated a scalable concept using RE-123 HTS tapes that are assembled to Roebel type conductors. This concept can be expanded to form Rutherford cables as starting point for a development of a high current fusion cable. The status and prospect of using HTS conductors for fusion is discussed.

W.H. Fietz; R. Heller; S.I. Schlachter; W. Goldacker

2011-01-01T23:59:59.000Z

497

High temperature crystalline superconductors from crystallized glasses  

DOE Patents (OSTI)

A method of preparing a high temperature superconductor from an amorphous phase. The method involves preparing a starting material of a composition of Bi.sub.2 Sr.sub.2 Ca.sub.3 Cu.sub.4 Ox or Bi.sub.2 Sr.sub.2 Ca.sub.4 Cu.sub.5 Ox, forming an amorphous phase of the composition and heat treating the amorphous phase for particular time and temperature ranges to achieve a single phase high temperature superconductor.

Shi, Donglu (Downers Grove, IL)

1992-01-01T23:59:59.000Z

498

Measure Guideline: High Efficiency Natural Gas Furnaces  

SciTech Connect

This Measure Guideline covers installation of high-efficiency gas furnaces. Topics covered include when to install a high-efficiency gas furnace as a retrofit measure, how to identify and address risks, and the steps to be used in the selection and installation process. The guideline is written for Building America practitioners and HVAC contractors and installers. It includes a compilation of information provided by manufacturers, researchers, and the Department of Energy as well as recent research results from the Partnership for Advanced Residential Retrofit (PARR) Building America team.

Brand, L.; Rose, W.

2012-10-01T23:59:59.000Z

499

A High Resolution Scale-of-four  

DOE R&D Accomplishments (OSTI)

A high resolution scale-of-four has been developed to be used in conjunction with the nuclear particle detection devices in applications where the counting rate is unusually high. Specifically, it is intended to precede the commercially available medium resolution scaling circuits and so decrease the resolving time of the counting system. The circuit will function reliably on continuously recurring pulses separated by less than 0.1 microseconds. It will resolve two pulses (occurring at a moderate repetition rate) which are spaced at 0.04 microseconds. A five-volt input signal is sufficient to actuate the device.

Fitch, V.

1949-08-25T23:59:59.000Z

500

Frustrated phase separation and high temperature superconductivity  

SciTech Connect

A dilute system of neutral holes in an antiferromagnet separates into a hole-rich and a hole-poor phase. The phase separation is frustrated by long-range Coulomb interactions but, provided the dielectric constant is sufficiently large, there remain large-amplitude low-energy fluctuations in the hole density at intermediate length scales. The extensive experimental evidence showing that this behavior giver, a reasonable picture of high temperature superconductors is surveyed. Further, it is shown that the scattering of mobile holes from the local density fluctuations may account for the anomalous normal-state properties of high temperature superconductors and also provide the mechanism of pairing.

Emery, V.J. [Brookhaven National Lab., Upton, NY (United States); Kivelson, S.A. [California Univ., Los Angeles, CA (United States). Dept. of Physics

1992-09-01T23:59:59.000Z