Powered by Deep Web Technologies
Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Fracture analysis of axially cracked pressure tube of pressurized heavy water reactor  

SciTech Connect (OSTI)

Three Dimensional (313) finite element elastic plastic fracture analysis was done for through wall axially cracked thin pressure tubes of 220 MWe Indian Pressurized Heavy Water Reactor. The analysis was done for Zr-2 and Zr-2.5Nb pressure tubes operating at 300{degrees}C and subjected to 9.5 Mpa internal pressure. Critical crack length was determined based on tearing instability concept. The analysis included the effect of crack face pressure due to the leaking fluid from tube. This effect was found to be significant for pressure tubes. The available formulae for calculating J (for axially cracked tubes) do not take into account the effect of crack face pressure. 3D finite element analysis also gives insight into variation of J across the thickness of pressure tube. It was observed that J is highest at the mid-surface of tube. The results have been presented in the form of across the thickness average J value and a peak factor on J. Peak factor on J is ratio of J at mid surface to average J value. Crack opening area for different cracked lengths was calculated from finite element results. The fracture assessment of pressure tubes was also done using Central Electricity Generating Board R-6 method. Ductile tearing was considered.

Krishnan, S.; Bhasin, V.; Mahajan, S.C. [Bhabha Atomic Research Centre, Bombay (India)] [and others

1997-04-01T23:59:59.000Z

2

Field measurement of lateral earth pressures on retaining walls  

E-Print Network [OSTI]

FIELD MEASUREMENT OF LATERAL EARTH PRESSURES ON RETAINING WALLS A Thesis by Michael Riggins Submitted to the Graduate College of Texas ARM University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE August 1974... Major Subject: Civil Engineering FIELD MEASUREMENT OF LATERAL EARTH PRESSURES ON RETAINING WALLS A Thesis by Michael Riggins Approved as to style and content by: Cha rman of Committee Memb r Head of Departm t P Etc Member August 1974 ABSTRACT...

Riggins, Michael

1974-01-01T23:59:59.000Z

3

Field measurements of earth pressure on a cantilever retaining wall  

E-Print Network [OSTI]

FIELD MEASUREMENTS OF EARTH PRESSURE ON A CANTILEVER RETAINING WALL A Thesis by LARRY WAYNE SCHULZE Submitted to the Graduate College Texas A&M University in Partial fulfillment of the requirements for the degree of MASTER OF SCIENCE... December 1980 Major Subject: Civil Engineering FIELD MEASUREMENTS OF EARTH PRESSURES ON A CANTILEVER RETAINING WALL A Thesis by LARRY WAYNE SCHULZE Approved as to style and content by: Harry M. Coyle ? C airman of Committee Wayne . Dunlap - Member...

Schulze, Larry Wayne

1980-01-01T23:59:59.000Z

4

Pressure and impulse scaling methods for wall impact in ICF (inertial confinement fusion)  

SciTech Connect (OSTI)

The design of the first structural wall (FSW) in an inertial confinement fusion (ICF) reactor requires some knowledge of the expected wall loading produced by x-ray and neutron deposition; specifically in the High Yield Lithium Injection Fusion Energy (HYLIFE) reactor, wall loading results from two sources -- gas shock and liquid impact. Gas shock is derived from x-ray deposition in the thin layers of exposed blanket material, producing ionized vapor, which will generate gas shock on the FSW. Liquid impact, on the other hand, results from the acceleration of liquid blanket material by two possible forces -- the drag from vapor expansion through the blanket material and the neutron-induced isochoric disassembly process. Both impacts, however, are coupled by the interaction of hot gas expanding through the liquid blanket. This paper discusses scaling methods for estimating pressure and impulse on the HYLIFE FSW from these impacts. In particular, this paper reviews simple analytical and numerical techniques, and the use of experimental results in the estimation of wall impacts for the HYLIFE blanket geometry. Considered important in the analyses are supersonic flow through jet arrays and isochoric disassembly. Given the same initial parameters as those used in previous HYLIFE studies, the techniques described here yield results comparable to the previous studies utilizing heavy numerical simulation.

Liu, J.C.; Chen, X.M.; Schrock, V.E. (California Univ., Berkeley, CA (USA). Dept. of Nuclear Engineering); Orth, C.D. (Lawrence Livermore National Lab., CA (USA))

1990-01-01T23:59:59.000Z

5

Flowfield and wall pressure characteristics downstream of a boundary layer suction device.  

E-Print Network [OSTI]

Flowfield and wall pressure characteristics downstream of a boundary layer suction device. Meagan A-dimensional slit can significantly reduce the fluctuating wall pressure immediately downstream of the suction slit momentum regions of the flow with the wall at the downstream edge of the suction slit. The third region

Tinney, Charles E.

6

Correlation for the Vapor Pressure of Heavy Water From the Triple Point to the Critical Point  

E-Print Network [OSTI]

Correlation for the Vapor Pressure of Heavy Water From the Triple Point to the Critical Point Allan the vapor pressure of heavy water (D2O) from its triple point to its critical point. This work takes Institute of Physics. Key words: D2O; heavy water; ITS-90; vapor pressure. Contents 1. Introduction

Magee, Joseph W.

7

Interior Duct Wall Pressure Downstream of a Low-Speed Scott C. Morris  

E-Print Network [OSTI]

Interior Duct Wall Pressure Downstream of a Low-Speed Rotor Scott C. Morris , David B. Stephens The region downstream of a ducted rotor has been experimentally investigated in terms of its wake the description of the flow field and wall pressure in the region downstream of the rotor. Measurements involving

Alonso, Juan J.

8

Elastic properties and pressure-induced phase transitions of single-walled carbon nanotubes  

E-Print Network [OSTI]

Elastic properties and pressure-induced phase transitions of single-walled carbon nanotubes S-walled carbon nanotubes under hydrostatic pressure by first-princi- ples calculations. The circular tubes of carbon nanotubes has been studied with a variety of experimental techniques. Most of these studies seemed

Nabben, Reinhard

9

Seismic Earth Pressure Development in Sheet Pile Retaining Walls: A Numerical Study  

E-Print Network [OSTI]

The design of retaining walls requires the complete knowledge of the earth pressure distribution behind the wall. Due to the complex soil-structure effect, the estimation of earth pressure is not an easy task; even in the static case. The problem becomes even more complex for the dynamic (i.e., seismic) analysis and design of retaining walls. Several earth pressure models have been developed over the years to integrate the dynamic earth pressure with the static earth pressure and to improve the design of retaining wall in seismic regions. Among all the models, MononobeOkabe (M-O) method is commonly used to estimate the magnitude of seismic earth pressures in retaining walls and is adopted in design practices around the world (e.g., EuroCode and Australian Standards). However, the M-O method has several drawbacks and does not provide reliable estimate of the earth pressure in many instances. This study investigates the accuracy of the M-O method to predict the dynamic earth pressure in sheet pile wall. A 2D pl...

Rajeev, P; Sivakugan, N

2015-01-01T23:59:59.000Z

10

Wall-pressure and PIV analysis for microbubble drag reduction investigation  

E-Print Network [OSTI]

friction reductions were observed when the microbubbles were injected. Several measurements of wall-pressure were taken at various Reynolds numbers that ranged from 300 up to 6154. No significant drag reduction was observed for flows in the laminar range...

Dominguez Ontiveros, Elvis Efren

2005-11-01T23:59:59.000Z

11

Experimental measurement and analysis of wall pressure distribution for a 50% eccentric whirling annular seal  

E-Print Network [OSTI]

, whirl ratios ranging between ? 0.5 were tested. From the collected data a detailed analysis of wall pressures along the seal surface is performed following the technique described by Winslow (1994) and Robic (1999)....

Suryanarayanan, Arun

2004-11-15T23:59:59.000Z

12

Raman spectroscopy on single and multi-walled nanotubes under high pressure  

E-Print Network [OSTI]

dependence of the high-energy Raman modes in single and multi-walled carbon nanotubes was measuredRaman spectroscopy on single and multi-walled nanotubes under high pressure C. Thomsen, S. Reich, H properties of carbon nanotubes have become of scienti c interest since it was recognized that the low atomic

Nabben, Reinhard

13

Measurements of earth pressures for the design modification of cantilever retaining walls  

E-Print Network [OSTI]

MEASUREMENTS OF EARTH PRESSURES FOR THE DESIGN MODIFICATION OF CANTILEVER RETAINING WALLS A Thesis by William Pri kryl Submitted to the Graduate College Texas ASM University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE May 1979 Major Subject: Civil Engineering MEASUREMENTS OF EARTH PRESSURES FOR THE DESIGN MODIFICATION OF CANTILEVER RETAINING WALLS A Thesis by William Prikryl Approved as to style and content by: jl ~, E Harry M. Coyle ? Chairman...

Prikryl, William

1979-01-01T23:59:59.000Z

14

New retaining wall design criteria based on lateral earth pressure measurements  

E-Print Network [OSTI]

NEW RETAINING WALL DESIGN CRITERIA BASED ON LATERAL EARTH PRESSURE MEASUREMENTS A Thesis by William V. ' Wright Submitted to the Graduate College of Texas A & M University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE August 1975 Major Subject: Civil Engineering NEW RETAINING WALL DESIGN CRITERIA BASED ON LATERAL EARTH PRESSURE MEASUREMENTS A thesi s by William V. Wright (Chairman of Commi ttee) (M ber) (Head of Department) 0'( (Member) August 1975...

Wright, William Vincent

1975-01-01T23:59:59.000Z

15

High-R Walls for New Construction Structural Performance: Wind Pressure Testing  

SciTech Connect (OSTI)

This technical report is focused primarily on laboratory testing that evaluates wind pressure performance characteristics for wall systems constructed with exterior insulating sheathing. This research and test activity will help to facilitate the ongoing use of non-structural sheathing options and provide a more in-depth understanding of how wall system layers perform in response to high wind perturbations normal to the surface.

DeRenzis, A.; Kochkin, V.

2013-01-01T23:59:59.000Z

16

Dynamic pressure and shear stress measurements on the stator wall of whirling annular seals  

E-Print Network [OSTI]

Dynamic pressure and shear stress measurements on the stator wall of whirling annular seals are presented. Two flow conditions (Re=12,000 & 24,000), two seal speeds (Ta=3,300 & 6,600) and three eccentricity ratios (0, 10, & 50% of the clearance...

Winslow, Robert Bradley

1994-01-01T23:59:59.000Z

17

Experimental measurement of phase averaged wall-pressure distributions for a 25% eccentric whirling annular seal  

E-Print Network [OSTI]

Instantaneous wall-pressure data were recorded for a 25% eccentric whirling annular seal for rotor speeds of 1800RPM and 3600RPM, axial Reynolds numbers of 24000 and 12000, and whirl ratios of 0.1-1.0 following the procedure set forth by Winslow...

Cusano, Domenic

2006-08-16T23:59:59.000Z

18

High Pressure Phase Transformations in Heavy Rare Earth Metals and Connections to Actinide Crystal Structures  

SciTech Connect (OSTI)

High-pressure studies have been performed on heavy rare earth metals Terbium (Tb) to 155 GPa and Holmium (Ho) to 134 GPa in a diamond anvil cell at room temperature. The following crystal structure sequence was observed in both metals hcp {yields} Sm-type {yields} dhcp {yields} distorted fcc (hR-24) {yields} monoclinic (C2/m) with increasing pressure. The last transformation to a low symmetry monoclinic phase is accompanied by a volume collapse of 5 % for Tb at 51 GPa and a volume collapse of 3 % for Ho at 103 GPa. This volume collapse under high pressure is reminiscent of f-shell delocalization in light rare earth metal Cerium (Ce), Praseodymium (Pr), and heavy actinide metals Americium (Am) and Curium (Cm). The orthorhombic Pnma phase that has been reported in Am and Cm after f-shell delocalization is not observed in heavy rare earth metals under high pressures. (authors)

Vohra, Yogesh K.; Sangala, Bagvanth Reddy; Stemshorn, Andrew K. [Physics, University of Alabama at Birmingham (UAB), 310 Campbell Hall, 1300 University Boulevard, Birmingham, AL, 35294-1170 (United States); Hope, Kevin M. [Biology, Chemistry, and Mathematics, University of Montevallo, Harman Hall, Station 6480, Montevallo, AL, 35115 (United States)

2008-07-01T23:59:59.000Z

19

Field measurements of lateral earth pressures on a pre-cast panel retaining wall  

E-Print Network [OSTI]

OF SCIENCE August 1973 Major Subject: Civil Engineering FIELD MEASUREMENTS OF LATERAL EARTH PRESSURES ON A PRE-CAST PANEL RETAINING WALL A Thesis by DAVID MONROE PRESCOTT Approved as to sty1e and content by: Chai man o Co ttee~ ember ead of Departm... in Appendix I. (The style and format of this thesis follows that used by the Journal of the Soil Mechanics and Foundations Division, Procee ings, of t e American Society of Civil Engineers result of some large scale earth pressure tests at Massachusetts...

Prescott, David Monroe

1973-01-01T23:59:59.000Z

20

Evaluation of anticipatory signal to steam generator pressure control program for 700 MWe Indian pressurized heavy water reactor  

SciTech Connect (OSTI)

700 MWe Indian Pressurized Heavy Water Reactor (IPHWR) is horizontal channel type reactor with partial boiling at channel outlet. Due to boiling, it has a large volume of vapor present in the primary loops. It has two primary loops connected with the help of pressurizer surge line. The pressurizer has a large capacity and is partly filled by liquid and partly by vapor. Large vapor volume improves compressibility of the system. During turbine trip or load rejection, pressure builds up in Steam Generator (SG). This leads to pressurization of Primary Heat Transport System (PHTS). To control pressurization of SG and PHTS, around 70% of the steam generated in SG is dumped into the condenser by opening Condenser Steam Dump Valves (CSDVs) and rest of the steam is released to the atmosphere by opening Atmospheric Steam Discharge Valves (ASDVs) immediately after sensing the event. This is accomplished by adding anticipatory signal to the output of SG pressure controller. Anticipatory signal is proportional to the thermal power of reactor and the proportionality constant is set so that SG pressure controller's output jacks up to ASDV opening range when operating at 100% FP. To simulate this behavior for 700 MWe IPHWR, Primary and secondary heat transport system is modeled. SG pressure control and other process control program have also been modeled to capture overall plant dynamics. Analysis has been carried out with 3-D neutron kinetics coupled thermal hydraulic computer code ATMIKA.T to evaluate the effect of the anticipatory signal on PHT pressure and over all plant dynamics during turbine trip in 700 MWe IPHWR. This paper brings out the results of the analysis with and without considering anticipatory signal in SG pressure control program during turbine trip. (authors)

Pahari, S.; Hajela, S.; Rammohan, H. P.; Malhotra, P. K.; Ghadge, S. G. [Nuclear Power Corporation of India Limited, Nabhikiya Urja Bhavan, Anushakti Nagar, Mumbai, PIN-400094 (India)

2012-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Effect of confining wall potential on charged collimated dust beam in low-pressure plasma  

SciTech Connect (OSTI)

The effect of confining wall potential on charged collimated dust beam in low-pressure plasma has been studied in a dusty plasma experimental setup by applying electrostatic field to each channel of a multicusp magnetic cage. Argon plasma is produced by hot cathode discharge method at a pressure of 5×10{sup ?4} millibars and is confined by a full line cusped magnetic field confinement system. Silver dust grains are produced by gas-evaporation technique and move upward in the form of a collimated dust beam due to differential pressure maintained between the dust and plasma chambers. The charged grains in the beam after coming out from the plasma column enter into the diagnostic chamber and are deflected by a dc field applied across a pair of deflector plates at different confining potentials. Both from the amount of deflection and the floating potential, the number of charges collected by the dust grains is calculated. Furthermore, the collimated dust beam strikes the Faraday cup, which is placed above the deflector plates, and the current (?pA) so produced is measured by an electrometer at different confining potentials. The experimental results demonstrate the significant effect of confining wall potential on charging of dust grains.

Kausik, S. S.; Kakati, B.; Saikia, B. K. [Centre of Plasma Physics, Institute for Plasma Research, Sonapur 782 402 (India)] [Centre of Plasma Physics, Institute for Plasma Research, Sonapur 782 402 (India)

2013-05-15T23:59:59.000Z

22

Crack opening area estimates in pressurized through-wall cracked elbows under bending  

SciTech Connect (OSTI)

One of the most important aspects in the leak-before-break approach is the estimation of the crack opening area corresponding to potential through-wall cracks at critical locations during plant operation. In order to provide a reasonable lower bound to the leak area under such loading conditions, numerous experimental and numerical programs have been developed in USA, U.K. and FRG and widely discussed in literature. This paper aims to extend these investigations on a class of pipe elbows characteristic of PWR main coolant piping. The paper is divided in three main parts. First, a new simplified estimation scheme for leakage area is described, based on the reference stress method. This approach mainly developed in U.K. and more recently in France provides a convenient way to account for the non-linear behavior of the material. Second, the method is carried out for circumferential through-wall cracks located in PWR elbows subjected to internal pressure. Finite element crack area results are presented and comparisons are made with our predictions. Finally, in the third part, the discussion is extended to elbows under combined pressure and in plane bending moment.

Franco, C.; Gilles, P.; Pignol, M.

1997-04-01T23:59:59.000Z

23

Seismic Earth Pressures on Retaining Structures and Basement Walls in Cohesionless Soils  

E-Print Network [OSTI]

? H) Normalized Dynamic Earth Pressure ( ? AE / ? H) Time(H=1 Time(sec) Figure A.64. Total earth pressure time series38 ii 3.7.3. Earth Pressure

Geraili Mikola, Roozbeh

2012-01-01T23:59:59.000Z

24

Modeling and simulation of a high pressure hydrogen storage tank with dynamic wall.  

E-Print Network [OSTI]

??Hydrogen storage is one of the divisions of hydrogen powered vehicles technology. To increase performances of high pressure hydrogen storage tanks, a multilayered design is… (more)

Cumalioglu, Ilgaz

2005-01-01T23:59:59.000Z

25

Modeling and simulation of a high pressure hydrogen storage tank with Dynamic Wall.  

E-Print Network [OSTI]

??Hydrogen storage is one of the divisions of hydrogen powered vehicles technology. To increase performances of high pressure hydrogen storage tanks, a multilayered design is… (more)

Cumalioglu, Ilgaz

2005-01-01T23:59:59.000Z

26

Very long single- and few-walled boron nitride nanotubes via the pressurized vapor/condenser method  

SciTech Connect (OSTI)

Boron nitride nanotubes (BNNTs) are desired for their exceptional mechanical, electronic, thermal, structural, textural, optical, and quantum properties. A new method for producing long, small-diameter, single- and few-walled, boron nitride nanotubes (BNNTs) in macroscopic quantities is reported. The pressurized vapor/condenser (PVC) method produces, without catalysts, highly crystalline, very long, small-diameter, BNNTs. Palm-sized, cotton-like masses of BNNT raw material were grown by this technique and spun directly into centimeters-long yarn. Nanotube lengths were observed to be 100 times that of those grown by the most closely related method. Self-assembly and growth models for these long BNNTs are discussed.

Michael W. Smith, Kevin Jordan, Cheol Park, Jae-Woo Kim, Peter Lillehei, Roy Crooks, Joycelyn Harrison

2009-11-01T23:59:59.000Z

27

1-Dimensional simulation of thermal annealing in a commercial nuclear power plant reactor pressure vessel wall section  

SciTech Connect (OSTI)

The objective of this work was to provide experimental heat transfer boundary condition and reactor pressure vessel (RPV) section thermal response data that can be used to benchmark computer codes that simulate thermal annealing of RPVS. This specific protect was designed to provide the Electric Power Research Institute (EPRI) with experimental data that could be used to support the development of a thermal annealing model. A secondary benefit is to provide additional experimental data (e.g., thermal response of concrete reactor cavity wall) that could be of use in an annealing demonstration project. The setup comprised a heater assembly, a 1.2 in {times} 1.2 m {times} 17.1 cm thick [4 ft {times} 4 ft {times} 6.75 in] section of an RPV (A533B ferritic steel with stainless steel cladding), a mockup of the {open_quotes}mirror{close_quotes} insulation between the RPV and the concrete reactor cavity wall, and a 25.4 cm [10 in] thick concrete wall, 2.1 in {times} 2.1 in [10 ft {times} 10 ft] square. Experiments were performed at temperature heat-up/cooldown rates of 7, 14, and 28{degrees}C/hr [12.5, 25, and 50{degrees}F/hr] as measured on the heated face. A peak temperature of 454{degrees}C [850{degrees}F] was maintained on the heated face until the concrete wall temperature reached equilibrium. Results are most representative of those RPV locations where the heat transfer would be 1-dimensional. Temperature was measured at multiple locations on the heated and unheated faces of the RPV section and the concrete wall. Incident heat flux was measured on the heated face, and absorbed heat flux estimates were generated from temperature measurements and an inverse heat conduction code. Through-wall temperature differences, concrete wall temperature response, heat flux absorbed into the RPV surface and incident on the surface are presented. All of these data are useful to modelers developing codes to simulate RPV annealing.

Nakos, J.T.; Rosinski, S.T.; Acton, R.U.

1994-11-01T23:59:59.000Z

28

The pressure of strong coupling lattice QCD with heavy quarks, the hadron resonance gas model and the large N limit  

E-Print Network [OSTI]

In this paper we calculate the pressure of pure lattice Yang-Mills theories and lattice QCD with heavy quarks by means of strong coupling expansions. Dynamical fermions are introduced with a hopping parameter expansion, which also allows for the incorporation of finite quark chemical potential. We show that in leading orders the results are in full agreement with expectations from the hadron resonance gas model, thus validating it with a first principles calculation. For pure Yang-Mills theories we obtain the corresponding ideal glueball gas, in QCD with heavy quarks our result equals that of an ideal gas of mesons and baryons. Another finding is that the Yang-Mills pressure in the large N limit is of order $\\sim N^0$ to the calculated orders, when the inverse 't Hooft coupling is used as expansion parameter. This property is expected in the confined phase, where our calculations take place.

Jens Langelage; Owe Philipsen

2010-02-08T23:59:59.000Z

29

B-meson decay constants from 2+1-flavor lattice QCD with domain-wall light quarks and relativistic heavy quarks  

E-Print Network [OSTI]

We calculate the B-meson decay constants f_B, f_Bs, and their ratio in unquenched lattice QCD using domain-wall light quarks and relativistic b-quarks. We use gauge-field ensembles generated by the RBC and UKQCD collaborations using the domain-wall fermion action and Iwasaki gauge action with three flavors of light dynamical quarks. We analyze data at two lattice spacings of a ~ 0.11, 0.086 fm with unitary pion masses as light as M_pi ~ 290 MeV; this enables us to control the extrapolation to the physical light-quark masses and continuum. For the b-quarks we use the anisotropic clover action with the relativistic heavy-quark interpretation, such that discretization errors from the heavy-quark action are of the same size as from the light-quark sector. We renormalize the lattice heavy-light axial-vector current using a mostly nonperturbative method in which we compute the bulk of the matching factor nonperturbatively, with a small correction, that is close to unity, in lattice perturbation theory. We also improve the lattice heavy-light current through O(alpha_s a). We extrapolate our results to the physical light-quark masses and continuum using SU(2) heavy-meson chiral perturbation theory, and provide a complete systematic error budget. We obtain f_B0 = 199.5(12.6) MeV, f_B+ = 195.6(14.9) MeV, f_Bs = 235.4(12.2) MeV, f_Bs/f_B0 = 1.197(50), and f_Bs/f_B+ = 1.223(71), where the errors are statistical and total systematic added in quadrature. These results are in good agreement with other published results and provide an important independent cross check of other three-flavor determinations of $B$-meson decay constants using staggered light quarks.

Norman H. Christ; Jonathan M. Flynn; Taku Izubuchi; Taichi Kawanai; Christoph Lehner; Amarjit Soni; Ruth S. Van de Water; Oliver Witzel

2015-02-02T23:59:59.000Z

30

Rheological behavior of heavy oil and water mixtures at high pressures and high temperatures  

E-Print Network [OSTI]

were compared to the existing correlations. This effort showed that all correlations' constants have to be tuned to match the experimental results. Our further analysis examined how to apply mixing rules in predicting viscosity of heavy oil and its...

Setiadarma, Agustinus

2002-01-01T23:59:59.000Z

31

E-Print Network 3.0 - advanced pressurized heavy Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

suppZ6ment au noll, Tome 41, novembre 1980, page C9-423 EXPERIMENTAL STUDY OF A FREE-VORTEX AERODYNAMIC WINDOW Summary: -Harima Heavy Industries, 1-15, Toyosu 3 chome, Koto-Ku,...

32

The determination of the turbulent intensities in a transitional flow from a smooth to a rough wall with zero pressure gradient in a two-dimensional channel  

E-Print Network [OSTI]

THE DETERMINATION OF THE TURBULENT INTENSITIES IN A TRANSITIONAL FLOW FROM A SMOOTH TO A ROUGH WALL WITH ZERO PRESSURE GRADIENT IN A TWO-DIMENSIONAL CHANNEL A Thesis By Ol3AIDU I. ISLAM Submitted to the Graduate School of. tire Agricultural... WALL WITH ZERO PRESSURE GRADIENT IN A TWO DIMENSIONAL. GHANNEL A Thesis By OBAIDUL ISLAM Approved as to style and content by: F / F Ghairma p'f mm tg Head of Department May 1963 ACKNOWLEDGMENTS Grateful acknowledgment is made to the Texas...

Islam, Obaidul

1963-01-01T23:59:59.000Z

33

Review of industry efforts to manage pressurized water reactor feedwater nozzle, piping, and feedring cracking and wall thinning  

SciTech Connect (OSTI)

This report presents a review of nuclear industry efforts to manage thermal fatigue, flow-accelerated corrosion, and water hammer damage to pressurized water reactor (PWR) feedwater nozzles, piping, and feedrings. The review includes an evaluation of design modifications, operating procedure changes, augmented inspection and monitoring programs, and mitigation, repair and replacement activities. Four actions were taken: (a) review of field experience to identify trends of operating events, (b) review of technical literature, (c) visits to PWR plants and a PWR vendor, and (d) solicitation of information from 8 other countries. Assessment of field experience is that licensees have apparently taken sufficient action to minimize feedwater nozzle cracking caused by thermal fatigue and wall thinning of J-tubes and feedwater piping. Specific industry actions to minimize the wall-thinning in feedrings and thermal sleeves were not found, but visual inspection and necessary repairs are being performed. Assessment of field experience indicates that licensees have taken sufficient action to minimize steam generator water hammer in both top-feed and preheat steam generators. Industry efforts to minimize multiple check valve failures that have allowed backflow of steam from a steam generator and have played a major role in several steam generator water hammer events were not evaluated. A major finding of this review is that analysis, inspection, monitoring, mitigation, and replacement techniques have been developed for managing thermal fatigue and flow-accelerated corrosion damage to feedwater nozzles, piping, and feedrings. Adequate training and appropriate applications of these techniques would ensure effective management of this damage.

Shah, V.N.; Ware, A.G.; Porter, A.M.

1997-03-01T23:59:59.000Z

34

Rheology and microstructural evolution in pressure-driven flow of a magnetorheological fluid with strong particle-wall interactions  

E-Print Network [OSTI]

The interaction between magnetorheological (MR) fluid particles and the walls of the device that retain the field-responsive fluid is critical as this interaction provides the means for coupling the physical device to the ...

Ocalan, Murat

35

Tokamak reactor first wall  

DOE Patents [OSTI]

This invention relates to an improved first wall construction for a tokamak fusion reactor vessel, or other vessels subjected to similar pressure and thermal stresses.

Creedon, R.L.; Levine, H.E.; Wong, C.; Battaglia, J.

1984-11-20T23:59:59.000Z

36

Influence of the reactor wall composition on radicals' densities and total pressure in Cl{sub 2} inductively coupled plasmas: II. During silicon etching  

SciTech Connect (OSTI)

In an industrial inductively coupled plasma reactor dedicated to silicon etching in chlorine-based chemistry, the density of Cl{sub 2} molecules and the gas temperature are measured by means of laser absorption techniques, the density of SiCl{sub x} (x{<=}2) radicals by broadband absorption spectroscopy, the density of SiCl{sub 4} and ions by mass spectrometry, and the total gas pressure with a capacitance gauge. These measurements permit us to estimate the mole fractions of Cl, SiCl{sub 4}, and etch product radicals when etching a 200 mm diameter silicon wafer. The pure Cl{sub 2} plasma is operated in well prepared chamber wall coating with a thin film of SiOCl, AlF, CCl, or TiOCl. The impact of the chemical nature of the reactor wall's coatings on these mole fractions is studied systematically. We show that the reactor wall coatings have a huge influence on the radicals densities, but this is not only from the difference on Cl-Cl recombination coefficient on different surfaces. During silicon etching, SiCl{sub x} radicals sticking on the reactor walls are etched by Cl atoms and recycled into the plasma by forming volatile SiCl{sub 4}. Hence, the loss of Cl atoms in etching the wall deposited silicon is at least as important as their wall recombination in controlling the Cl atoms density. Furthermore, because SiCl{sub 4} is produced at high rate by both the wafer and reactor walls, it is the predominant etching product in the gas phase. However, the percentage of redeposited silicon that can be recycled into the plasma depends on the amount of oxygen present in the plasma: O atoms produced by etching the quartz roof window fix Si on the reactor walls by forming a SiOCl deposit. Hence, the higher the O density is, the lower the SiCl{sub 4} density will be, because silicon is pumped by the reactor walls and the SiOCl layer formed is not isotropically etched by chlorine. As a result, in the same pure Cl{sub 2} plasma at 20 mTorr, the SiCl{sub x} mole fraction can vary from 18% in a SiOCl-coated reactor, where the O density is the highest, to 62% in a carbon-coated reactor, where there is no O. In the latter case, most of the Cl mass injected in the reactor is stored in SiCl{sub 4} molecules, which results in a low silicon etch rate. In this condition, the Cl mass balance is verified within 10%, and from the silicon mass balance we concluded that SiCl{sub x} radicals have a high surface loss probability. The impact of the reactor wall coating on the etching process is thus important, but the mechanisms by which the walls control the plasma chemistry is much more complicated than a simple control through recombination reaction of halogen atoms on these surfaces.

Cunge, G.; Sadeghi, N.; Ramos, R. [Laboratoire des Technologies de la Microelectronique, CNRS, 17 rue des Martyrs (c/o CEA-LETI), 38054 Grenoble Cedex 9 (France); Laboratoire de Spectrometrie Physique (UMR 5588), Universite Joseph Fourier-Grenoble, and CNRS, BP 87, 38402 St. Martin d'Heres (France); Laboratoire des Technologies de la Microelectronique, CNRS, 17 rue des Martyrs (c/o CEA-LETI), 38054 Grenoble Cedex 9 (France)

2007-11-01T23:59:59.000Z

37

Assessment of Crack Detection in Heavy-Walled Cast Stainless Steel Piping Welds Using Advanced Low-Frequency Ultrasonic Methods  

SciTech Connect (OSTI)

Studies conducted at the Pacific Northwest National Laboratory in Richland, Washington, have focused on assessing the effectiveness and reliability of novel approaches to nondestructive examination (NDE) for inspecting coarse-grained, cast stainless steel reactor components. The primary objective of this work is to provide information to the U.S. Nuclear Regulatory Commission on the effectiveness and reliability of advanced NDE methods as related to the inservice inspection of safety-related components in pressurized water reactors (PWRs). This report provides progress, recent developments, and results from an assessment of low frequency ultrasonic testing (UT) for detection of inside surface-breaking cracks in cast stainless steel reactor piping weldments as applied from the outside surface of the components. Vintage centrifugally cast stainless steel piping segments were examined to assess the capability of low-frequency UT to adequately penetrate challenging microstructures and determine acoustic propagation limitations or conditions that may interfere with reliable flaw detection. In addition, welded specimens containing mechanical and thermal fatigue cracks were examined. The specimens were fabricated using vintage centrifugally cast and statically cast stainless steel materials, which are typical of configurations installed in PWR primary coolant circuits. Ultrasonic studies on the vintage centrifugally cast stainless steel piping segments were conducted with a 400-kHz synthetic aperture focusing technique and phased array technology applied at 500 kHz, 750 kHz, and 1.0 MHz. Flaw detection and characterization on the welded specimens was performed with the phased array method operating at the frequencies stated above. This report documents the methodologies used and provides results from laboratory studies to assess baseline material noise, crack detection, and length-sizing capability for low-frequency UT in cast stainless steel piping.

Anderson, Michael T.; Crawford, Susan L.; Cumblidge, Stephen E.; Denslow, Kayte M.; Diaz, Aaron A.; Doctor, Steven R.

2007-03-01T23:59:59.000Z

38

Heavy-Section Steel Irradiation Program on irradiation effects in light-water reactor pressure vessel materials  

SciTech Connect (OSTI)

The safety of commercial light-water nuclear plants is highly dependent on the structural integrity of the reactor pressure vessel (RPV). In the absence of radiation damage to the RPV, fracture of the vessel is difficult to postulate. Exposure to high energy neutrons can result in embrittlement of radiation-sensitive RPV materials. The Heavy-Section Steel Irradiation (HSSI) Program at Oak Ridge National Laboratory, sponsored by the US Nuclear Regulatory Commission (USNRC), is assessing the effects of neutron irradiation on RPV material behavior, especially fracture toughness. The results of these and other studies are used by the USNRC in the evaluation of RPV integrity and regulation of overall nuclear plant safety. In assessing the effects of irradiation, prototypic RPV materials are characterized in the unirradiated condition and exposed to radiation under varying conditions. Mechanical property tests are conducted to provide data which can be used in the development of guidelines for structural integrity evaluations, while metallurgical examinations and mechanistic modeling are performed to improve understanding of the mechanisms responsible for embrittlement. The results of these investigations, in conjunction with results from commercial reactor surveillance programs, are used to develop a methodology for the prediction of radiation effects on RPV materials. This irradiation-induced degradation of the materials can be mitigated by thermal annealing, i.e., heating the RPV to a temperature above that of normal operation. Thus, thermal annealing and evaluation of reirradiation behavior are major tasks of the HSSI Program. This paper describes the HSSI Program activities by summarizing some past and recent results, as well as current and planned studies. 30 refs., 8 figs., 1 tab.

Nanstad, R.K.; Corwin, W.R.; Alexander, D.J.; Haggag, F.M.; Iskander, S.K.; McCabe, D.E.; Sokolov, M.A.; Stoller, R.E. [Oak Ridge National Lab., TN (United States). Metals and Ceramics Div.

1995-07-01T23:59:59.000Z

39

Influence of the reactor wall composition on radicals' densities and total pressure in Cl{sub 2} inductively coupled plasmas: I. Without silicon etching  

SciTech Connect (OSTI)

Laser absorption at 355 nm is used to monitor the time variations of the Cl{sub 2} density in high-density industrial inductively coupled plasma. This technique is combined with the measurement of the gas temperature from the Doppler width of the 811.5 nm line of argon, added as a trace gas and with the measurement of the total gas pressure with a Baratron gauge. These measurements permit to estimate the mole fractions of Cl{sub 2} and Cl species in Cl{sub 2} inductively coupled plasmas in a waferless reactor. The impact of the chemical nature of the reactor wall coatings on the Cl and Cl{sub 2} mole fractions is studied systematically. We show that under otherwise identical plasma conditions, the Cl mole fraction is completely different when the plasma is operated in SiOCl, AlF, CCl, or TiOCl coated reactors, because the homogeneous recombination probability of Cl atoms is strongly surface dependant. The Cl atom mole fraction reached at 100 W radiofrequency power in SiOCl coated reactor (80%) is much higher than that obtained at 900 W in a ''clean'' AlF reactor (40%). A simple zero-dimensional model permits to provide the recombination coefficient of Cl atoms, {gamma}{sub rec}: 0.005 on SiOCl film and about 0.3 on the other three coatings. It is proposed to get benefit of this very high sensitivity of Cl{sub 2} dissociation rate to the wall coating for the control of the chamber wall status from the Cl{sub 2} density measurements in standard conditions.

Cunge, G.; Sadeghi, N.; Ramos, R. [Laboratoire des Technologies de la Microelectronique, CNRS, 17 rue des Martyrs (c/o CEA-LETI), 38054 Grenoble Cedex 9 (France); Laboratoire de Spectrometrie Physique (UMR 5588), Universite Joseph Fourier-Grenoble, and CNRS, BP 87, 38402 St. Martin d'Heres (France); Laboratoire des Technologies de la Microelectronique, CNRS, 17 rue des Martyrs (c/o CEA-LETI), 38054 Grenoble Cedex 9 (France)

2007-11-01T23:59:59.000Z

40

The B->pi l nu and Bs->K l nu form factors and |Vub| from 2+1-flavor lattice QCD with domain-wall light quarks and relativistic heavy quarks  

E-Print Network [OSTI]

We calculate the form factors for B->pi l nu & Bs->K l nu decay in lattice QCD. We use the (2+1)-flavor RBC-UKQCD gauge field-ensembles generated with the domain-wall fermion and Iwasaki gauge actions. For the b quarks we use the anisotropic clover action with the relativistic heavy-quark interpretation. We analyze data at 2 lattice spacings a~0.11, 0.086 fm with pion masses as light as M_pi~290 MeV. We extrapolate our numerical results to the physical light-quark masses and to the continuum and interpolate in the pion/kaon energy using SU(2) "hard-pion" chiral perturbation theory. We provide complete systematic error budgets for the vector & scalar form factors f+(q^2) & f0(q2) for B->pi l nu & Bs ->K l nu at 3 momenta that span the q^2 range accessible in our numerical simulations. Next we extrapolate these results to q^2 = 0 using a model-independent z-parameterization based on analyticity & unitarity. We present our final results for f+(q^2) & f0(q^2) as the z coefficients and matr...

Flynn, J M; Kawanai, T; Lehner, C; Soni, A; Van de Water, R S; Witzel, O

2015-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Pressurizer tank upper support  

DOE Patents [OSTI]

A pressurizer tank in a pressurized water nuclear reactor is mounted between structural walls of the reactor on a substructure of the reactor, the tank extending upwardly from the substructure. For bearing lateral loads such as seismic shocks, a girder substantially encircles the pressurizer tank at a space above the substructure and is coupled to the structural walls via opposed sway struts. Each sway strut is attached at one end to the girder and at an opposite end to one of the structural walls, and the sway struts are oriented substantially horizontally in pairs aligned substantially along tangents to the wall of the circular tank. Preferably, eight sway struts attach to the girder at 90.degree. intervals. A compartment encloses the pressurizer tank and forms the structural wall. The sway struts attach to corners of the compartment for maximum stiffness and load bearing capacity. A valve support frame carrying the relief/discharge piping and valves of an automatic depressurization arrangement is fixed to the girder, whereby lateral loads on the relief/discharge piping are coupled directly to the compartment rather than through any portion of the pressurizer tank. Thermal insulation for the valve support frame prevents thermal loading of the piping and valves. The girder is shimmed to define a gap for reducing thermal transfer, and the girder is free to move vertically relative to the compartment walls, for accommodating dimensional variation of the pressurizer tank with changes in temperature and pressure.

Baker, Tod H. (O'Hara Township, Allegheny County, PA); Ott, Howard L. (Kiski Township, Armstrong County, PA)

1994-01-01T23:59:59.000Z

42

Pressurizer tank upper support  

DOE Patents [OSTI]

A pressurizer tank in a pressurized water nuclear reactor is mounted between structural walls of the reactor on a substructure of the reactor, the tank extending upwardly from the substructure. For bearing lateral loads such as seismic shocks, a girder substantially encircles the pressurizer tank at a space above the substructure and is coupled to the structural walls via opposed sway struts. Each sway strut is attached at one end to the girder and at an opposite end to one of the structural walls, and the sway struts are oriented substantially horizontally in pairs aligned substantially along tangents to the wall of the circular tank. Preferably, eight sway struts attach to the girder at 90[degree] intervals. A compartment encloses the pressurizer tank and forms the structural wall. The sway struts attach to corners of the compartment for maximum stiffness and load bearing capacity. A valve support frame carrying the relief/discharge piping and valves of an automatic depressurization arrangement is fixed to the girder, whereby lateral loads on the relief/discharge piping are coupled directly to the compartment rather than through any portion of the pressurizer tank. Thermal insulation for the valve support frame prevents thermal loading of the piping and valves. The girder is shimmed to define a gap for reducing thermal transfer, and the girder is free to move vertically relative to the compartment walls, for accommodating dimensional variation of the pressurizer tank with changes in temperature and pressure. 10 figures.

Baker, T.H.; Ott, H.L.

1994-01-11T23:59:59.000Z

43

The B->pi l nu and Bs->K l nu form factors and |Vub| from 2+1-flavor lattice QCD with domain-wall light quarks and relativistic heavy quarks  

E-Print Network [OSTI]

We calculate the form factors for B->pi l nu & Bs->K l nu decay in lattice QCD. We use the (2+1)-flavor RBC-UKQCD gauge field-ensembles generated with the domain-wall fermion and Iwasaki gauge actions. For the b quarks we use the anisotropic clover action with the relativistic heavy-quark interpretation. We analyze data at 2 lattice spacings a~0.11, 0.086 fm with pion masses as light as M_pi~290 MeV. We extrapolate our numerical results to the physical light-quark masses and to the continuum and interpolate in the pion/kaon energy using SU(2) "hard-pion" chiral perturbation theory. We provide complete systematic error budgets for the vector & scalar form factors f+(q^2) & f0(q^2) for B->pi l nu & Bs ->K l nu at 3 momenta that span the q^2 range accessible in our numerical simulations. Next we extrapolate these results to q^2 = 0 using a model-independent z-parameterization based on analyticity & unitarity. We present our final results for f+(q^2) & f0(q^2) as the z coefficients and matrix of correlations between them; this parameterizes the form factors over the entire kinematic range. Our results agree with other 3-flavor lattice-QCD determinations using staggered light quarks, and have comparable precision, thereby providing important independent checks. Both B->pi l nu & Bs->K l nu decays enable determinations of the CKM element |Vub|. To illustrate this, we perform a combined z-fit of our numerical B ->pi l nu form-factor data with experimental measurements of the branching fraction; we obtain |Vub| = 3.61(32) x 10^{-3}, where the error includes statistical and systematic uncertainties. The same approach can be applied to Bs->K l nu to provide an alternative determination of |Vub| once the process has been measured experimentally. Finally, we make predictions for B->pi l nu & Bs->K l nu differential branching fractions and forward-backward asymmetries in the Standard Model.

J. M. Flynn; T. Izubuchi; T. Kawanai; C. Lehner; A. Soni; R. S. Van de Water; O. Witzel

2015-02-07T23:59:59.000Z

44

On the use of the double floating probe method to infer the difference between the electron and the heavy particles temperatures in an atmospheric pressure, vortex-stabilized nitrogen plasma jet  

SciTech Connect (OSTI)

Sweeping double probe measurements in an atmospheric pressure direct current vortex-stabilized plasma jet are reported (plasma conditions: 100 A discharge current, N{sub 2} gas flow rate of 25 Nl/min, thoriated tungsten rod-type cathode, copper anode with 5 mm inner diameter). The interpretation of the double probe characteristic was based on a generalization of the standard double floating probe formulae for non-uniform plasmas coupled to a non-equilibrium plasma composition model. Perturbations caused by the current to the probe together with collisional and thermal processes inside the probe perturbed region were taken into account. Radial values of the average electron and heavy particle temperatures as well as the electron density were obtained. The calculation of the temperature values did not require any specific assumption about a temperature relationship between different particle species. An electron temperature of 10?900 ± 900 K, a heavy particle temperature of 9300 ± 900 K, and an electron density of about 3.5 × 10{sup 22} m{sup ?3} were found at the jet centre at 3.5 mm downstream from the torch exit. Large deviations from kinetic equilibrium were found toward the outer border of the plasma jet. These results showed good agreement with those previously reported by the authors by using a single probe technique. The calculations have shown that this method is particularly useful for studying spraying-type plasma torches operated at power levels of about 15 kW.

Prevosto, L., E-mail: prevosto@waycom.com.ar; Mancinelli, B. R. [Grupo de Descargas Eléctricas, Departamento Ingeniería Electromecánica, Facultad Regional Venado Tuerto (UTN), Laprida 651, 2600 Venado Tuerto, Santa Fe (Argentina)] [Grupo de Descargas Eléctricas, Departamento Ingeniería Electromecánica, Facultad Regional Venado Tuerto (UTN), Laprida 651, 2600 Venado Tuerto, Santa Fe (Argentina); Kelly, H. [Grupo de Descargas Eléctricas, Departamento Ingeniería Electromecánica, Facultad Regional Venado Tuerto (UTN), Laprida 651, 2600 Venado Tuerto, Santa Fe (Argentina) [Grupo de Descargas Eléctricas, Departamento Ingeniería Electromecánica, Facultad Regional Venado Tuerto (UTN), Laprida 651, 2600 Venado Tuerto, Santa Fe (Argentina); Instituto de Física del Plasma (CONICET), Departamento de Física, Facultad de Ciencias Exactas y Naturales (UBA) Ciudad Universitaria Pab. I, 1428 Buenos Aires (Argentina)

2014-05-15T23:59:59.000Z

45

Near-wall serpentine cooled turbine airfoil  

DOE Patents [OSTI]

A serpentine coolant flow path is formed by inner walls in a cavity between pressure and suction side walls of a turbine airfoil, the cavity partitioned by one or more transverse partitions into a plurality of continuous serpentine cooling flow streams each having a respective coolant inlet.

Lee, Ching-Pang

2014-10-28T23:59:59.000Z

46

Bremsstrahlung Radiation At a Vacuum Bubble Wall  

E-Print Network [OSTI]

When charged particles collide with a vacuum bubble, they can radiate strong electromagnetic waves due to rapid deceleration. Owing to the energy loss of the particles by this bremsstrahlung radiation, there is a non-negligible damping pressure acting on the bubble wall even when thermal equilibrium is maintained. In the non-relativistic region, this pressure is proportional to the velocity of the wall and could have influenced the bubble dynamics in the early universe.

Jae-Weon Lee; Kyungsub Kim; Chul H. Lee; Ji-ho Jang

2007-04-06T23:59:59.000Z

47

Innovative Composite Wall System for Sheathing Masonry Walls  

SciTech Connect (OSTI)

Existing Housing - Much of the older multifamily housing stock in the United States includes units in structures with uninsulated masonry walls. Included in this stock are two- and three-story walk-up apartments, larger apartment complexes, and public housing (both high- rise and townhouse). This older multifamily housing has seen years of heavy use that may have left the plaster wall marred or damaged. Long- term building settlement or movement may have cracked the plaster, sometimes severely. Moisture from invented kitchens and baths may have caused condensation on uninsulated exterior walls. At best this condensation has left stains on the paint or wallpaper. At worst it has supported mold and mildew growth, fouling the air and creating unhealthy living conditions. Deteriorating plaster and flaking paint also result from wet walls. The presence of flaking, lead-based paint in older (pre-1978) housing is a major public health concern. Children can suffer permanent mental handicaps and psychological disorders if they are subjected to elevated levels of lead, while adults can suffer hypertension and other maladies. Studies have found that, in some urban communities with older housing stocks, over 35% of children tested have elevated blood lead levels (Hastings, et al.: 1997). Nationally, nearly 22% of black, non-hispanic children living in pre-1946 housing were found to have elevated levels of lead in their blood (MWWR Article: February 21,1997). The deterioration of many of these walls is to the point that lead can freely enter the living space.

Wendt, Robert L. [Oak Ridge National Lab., TN (United States); Cavallo, James [Argonne National Lab., IL (United States)

1997-09-25T23:59:59.000Z

48

Wall to Wall Optimal Transport  

E-Print Network [OSTI]

The calculus of variations is employed to find steady divergence-free velocity fields that maximize transport of a tracer between two parallel walls held at fixed concentration for one of two constraints on flow strength: a fixed value of the kinetic energy or a fixed value of the enstrophy. The optimizing flows consist of an array of (convection) cells of a particular aspect ratio Gamma. We solve the nonlinear Euler-Lagrange equations analytically for weak flows and numerically (and via matched asymptotic analysis in the fixed energy case) for strong flows. We report the results in terms of the Nusselt number Nu, a dimensionless measure of the tracer transport, as a function of the Peclet number Pe, a dimensionless measure of the energy or enstrophy of the flow. For both constraints the maximum transport Nu_{MAX}(Pe) is realized in cells of decreasing aspect ratio Gamma_{opt}(Pe) as Pe increases. For the fixed energy problem, Nu_{MAX} \\sim Pe and Gamma_{opt} \\sim Pe^{-1/2}, while for the fixed enstrophy scenario, Nu_{MAX} \\sim Pe^{10/17} and Gamma_{opt} \\sim Pe^{-0.36}. We also interpret our results in the context of certain buoyancy-driven Rayleigh-Benard convection problems that satisfy one of the two intensity constraints, enabling us to investigate how the transport scalings compare with upper bounds on Nu expressed as a function of the Rayleigh number \\Ra. For steady convection in porous media, corresponding to the fixed energy problem, we find Nu_{MAX} \\sim \\Ra and Gamma_{opt} \\sim Ra^{-1/2}$, while for steady convection in a pure fluid layer between free-slip isothermal walls, corresponding to fixed enstrophy transport, Nu_{MAX} \\sim Ra^{5/12} and Gamma_{opt} \\sim Ra^{-1/4}.

Pedram Hassanzadeh; Gregory P. Chini; Charles R. Doering

2014-04-14T23:59:59.000Z

49

Effect of elasticity of wall on diffusion in nano channel  

SciTech Connect (OSTI)

Confining walls of nano channel are taken to be elastic to study their effect on the diffusion coefficient of fluid flowing through the channel. The wall is elastic to the extent that it responses to molecular pressure exerted by fluid. The model to study diffusion is based on microscopic considerations. Results obtained for fluid confining to 20 atomic diameter width contrasted with results obtained by considering rigid and smooth wall. The effect of roughness of wall on diffusion can be compensated by the elastic property of wall.

Tankeshwar, K., E-mail: tankesh@pu.ac.in [Computer Centre, Panjab University Chandigarh,- 160014 (India); Srivastava, Sunita [Department of Physics, Panjab University, Chandigarh 160014 (India)

2014-04-24T23:59:59.000Z

50

Near wall cooling for a highly tapered turbine blade  

SciTech Connect (OSTI)

A turbine blade having a pressure sidewall and a suction sidewall connected at chordally spaced leading and trailing edges to define a cooling cavity. Pressure and suction side inner walls extend radially within the cooling cavity and define pressure and suction side near wall chambers. A plurality of mid-chord channels extend radially from a radially intermediate location on the blade to a tip passage at the blade tip for connecting the pressure side and suction side near wall chambers in fluid communication with the tip passage. In addition, radially extending leading edge and trailing edge flow channels are located adjacent to the leading and trailing edges, respectively, and cooling fluid flows in a triple-pass serpentine path as it flows through the leading edge flow channel, the near wall chambers and the trailing edge flow channel.

Liang, George (Palm City, FL)

2011-03-08T23:59:59.000Z

51

First Wall and Operational Diagnostics  

SciTech Connect (OSTI)

In this chapter we review numerous diagnostics capable of measurements at or near the first wall, many of which contribute information useful for safe operation of a tokamak. There are sections discussing infrared cameras, visible and VUV cameras, pressure gauges and RGAs, Langmuir probes, thermocouples, and erosion and deposition measurements by insertable probes and quartz microbalance. Also discussed are dust measurements by electrostatic detectors, laser scattering, visible and IR cameras, and manual collection of samples after machine opening. In each case the diagnostic is discussed with a view toward application to a burning plasma machine such as ITER.

Lasnier, C; Allen, S; Boedo, J; Groth, M; Brooks, N; McLean, A; LaBombard, B; Sharpe, J; Skinner, C; Whyte, D; Rudakov, D; West, W; Wong, C

2006-06-19T23:59:59.000Z

52

Liquid Wall Chambers  

SciTech Connect (OSTI)

The key feature of liquid wall chambers is the use of a renewable liquid layer to protect chamber structures from target emissions. Two primary options have been proposed and studied: wetted wall chambers and thick liquid wall (TLW) chambers. With wetted wall designs, a thin layer of liquid shields the structural first wall from short ranged target emissions (x-rays, ions and debris) but not neutrons. Various schemes have been proposed to establish and renew the liquid layer between shots including flow-guiding porous fabrics (e.g., Osiris, HIBALL), porous rigid structures (Prometheus) and thin film flows (KOYO). The thin liquid layer can be the tritium breeding material (e.g., flibe, PbLi, or Li) or another liquid metal such as Pb. TLWs use liquid jets injected by stationary or oscillating nozzles to form a neutronically thick layer (typically with an effective thickness of {approx}50 cm) of liquid between the target and first structural wall. In addition to absorbing short ranged emissions, the thick liquid layer degrades the neutron flux and energy reaching the first wall, typically by {approx}10 x x, so that steel walls can survive for the life of the plant ({approx}30-60 yrs). The thick liquid serves as the primary coolant and tritium breeding material (most recent designs use flibe, but the earliest concepts used Li). In essence, the TLW places the fusion blanket inside the first wall instead of behind the first wall.

Meier, W R

2011-02-24T23:59:59.000Z

53

Method for pressure modulation of turbine sidewall cavities  

DOE Patents [OSTI]

A method is provided for controlling cooling air flow for pressure modulation of turbine components, such as the turbine outer sidewall cavities. The pressure at which cooling and purge air is supplied to the turbine outer side wall cavities is modulated, based on compressor discharge pressure (Pcd), thereby to generally maintain the back flow margin (BFM) so as to minimize excessive leakage and the consequent performance deterioration. In an exemplary embodiment, the air pressure within the third stage outer side wall cavity and the air pressure within the fourth stage outer side wall cavity are each controlled to a respective value that is a respective prescribed percentage of the concurrent compressor discharge pressure. The prescribed percentage may be determined from a ratio of the respective outer side wall pressure to compressor discharge pressure at Cold Day Turn Down (CDTD) required to provide a prescribed back flow margin.

Leone, Sal Albert (Scotia, NY); Book, Matthew David (Altamont, NY); Banares, Christopher R. (Schenectady, NY)

2002-01-01T23:59:59.000Z

54

System for pressure modulation of turbine sidewall cavities  

DOE Patents [OSTI]

A system and method are provided for controlling cooling air flow for pressure modulation of turbine components, such as the turbine outer sidewall cavities. The pressure at which cooling and purge air is supplied to the turbine outer side wall cavities is modulated, based on compressor discharge pressure (Pcd), thereby to generally maintain the back flow margin (BFM) so as to minimize excessive leakage and the consequent performance deterioration. In an exemplary embodiment, the air pressure within the third stage outer side wall cavity and the air pressure within the fourth stage outer side wall cavity are each controlled to a respective value that is a respective prescribed percentage of the concurrent compressor discharge pressure. The prescribed percentage may be determined from a ratio of the respective outer side wall pressure to compressor discharge pressure at Cold Day Turn Down (CDTD) required to provide a prescribed back flow margin.

Leone, Sal Albert (Scotia, NY); Book, Matthew David (Altamont, NY); Banares, Christopher R. (Schenectady, NY)

2002-01-01T23:59:59.000Z

55

Heavy Truck Engine Program  

SciTech Connect (OSTI)

The Heavy Duty Truck Engine Program at Cummins embodied three significant development phases. All phases of work strove to demonstrate a high level of diesel engine efficiency in the face of increasingly stringent emission requirements. Concurrently, aftertreatment system development and refinement was pursued in support of these efficiency demonstrations. The program's first phase focused on the demonstration in-vehicle of a high level of heavy duty diesel engine efficiency (45% Brake Thermal Efficiency) at a typical cruise condition while achieving composite emissions results which met the 2004 U.S. EPA legislated standards. With a combination of engine combustion calibration tuning and the development and application of Urea-based SCR and particulate aftertreatment, these demonstrations were successfully performed by Q4 of 2002. The second phase of the program directed efforts towards an in-vehicle demonstration of an engine system capable of meeting 2007 U.S. EPA legislated emissions requirements while achieving 45% Brake Thermal Efficiency at cruise conditions. Through further combustion optimization, the refinement of Cummins Cooled EGR architecture, the application of a high pressure common rail fuel system and the incorporation of optimized engine parasitics, Cummins Inc. successfully demonstrated these deliverables in Q2 of 2004. The program's final phase set a stretch goal of demonstrating 50% Brake Thermal Efficiency from a heavy duty diesel engine system capable of meeting 2010 U.S. EPA legislated emissions requirements. Cummins chose to pursue this goal through further combustion development and refinement of the Cooled EGR system architecture and also applied a Rankine cycle Waste Heat Recovery technique to convert otherwise wasted thermal energy to useful power. The engine and heat recovery system was demonstrated to achieve 50% Brake Thermal Efficiency while operating at a torque peak condition in second quarter, 2006. The 50% efficient engine system was capable of meeting 2010 emissions requirements through the application of NOx and particulate matter reduction techniques proven earlier in the program.

Nelson, Christopher

2009-01-08T23:59:59.000Z

56

Webs of Walls  

E-Print Network [OSTI]

Webs of domain walls are constructed as 1/4 BPS states in d=4, N=2 supersymmetric U(Nc) gauge theories with Nf hypermultiplets in the fundamental representation. Web of walls can contain any numbers of external legs and loops like (p,q) string/5-brane webs. We find the moduli space M of a 1/4 BPS equation for wall webs to be the complex Grassmann manifold. When moduli spaces of 1/2 BPS states (parallel walls) and the vacua are removed from M, the non-compact moduli space of genuine 1/4 BPS wall webs is obtained. All the solutions are obtained explicitly and exactly in the strong gauge coupling limit. In the case of Abelian gauge theory, we work out the correspondence between configurations of wall web and the moduli space CP^{Nf-1}.

Minoru Eto; Youichi Isozumi; Muneto Nitta; Keisuke Ohashi; Norisuke Sakai

2005-06-20T23:59:59.000Z

57

Four-wall turbine airfoil with thermal strain control for reduced cycle fatigue  

DOE Patents [OSTI]

A turbine airfoil (20B) with a thermal expansion control mechanism that increases the airfoil camber (60, 61) under operational heating. The airfoil has four-wall geometry, including pressure side outer and inner walls (26, 28B), and suction side outer and inner walls (32, 34B). It has near-wall cooling channels (31F, 31A, 33F, 33A) between the outer and inner walls. A cooling fluid flow pattern (50C, 50W, 50H) in the airfoil causes the pressure side inner wall (28B) to increase in curvature under operational heating. The pressure side inner wall (28B) is thicker than walls (26, 34B) that oppose it in camber deformation, so it dominates them in collaboration with the suction side outer wall (32), and the airfoil camber increases. This reduces and relocates a maximum stress area (47) from the suction side outer wall (32) to the suction side inner wall (34B, 72) and the pressure side outer wall (26).

Cambell, Christian X

2013-09-17T23:59:59.000Z

58

Heavy metal biosensor  

SciTech Connect (OSTI)

Compositions and methods are provided for detection of certain heavy metals using bacterial whole cell biosensors.

Hillson, Nathan J; Shapiro, Lucille; Hu, Ping; Andersen, Gary L

2014-04-15T23:59:59.000Z

59

Great Wall Starbucks  

E-Print Network [OSTI]

along the Great Wall. When you think about it, it's not a bad marketing strategy: the Wall is high, the stairs relentless; what better than an espresso to energize you for the steep climb up? On second thought, make that a double. #ceas #china #tsutsui...

Hacker, Randi; Gatewood, Tyler; Tsutsui, William

2006-03-29T23:59:59.000Z

60

The stimulation of heavy oil reservoirs with electrical resistance heating  

E-Print Network [OSTI]

. Equations for r? and P, were written using regression analysis. The calculation procedure is as follows: (1) calculate r?, (2) calculate the skin factor, s??, (3) calculate the heated oil production rate, q, ?, and (4) calculate the downhole power... of various heavy oils at 113 'F Fig. 23 ? Effect of CH, on the viscosity of various heavy oils at 171 'F Fig. 24 - Viscosity/pressure relationship for the recombined field sample Fig. 25 ? Smoothed viscosity/pressure relationship for the recombined...

Baylor, Blake Allen

1990-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Pressure &Pressure & TemperatureTemperature  

E-Print Network [OSTI]

to measure atmospheric pressure, and thermometer toprobe to measure atmospheric pressure, and thermometer toprobe to measure atmospheric pressure, and thermometer toprobe to measure atmospheric pressure, and thermometer to measure air temperature.measure air temperature.measure air temperature.measure air temperature

California at Santa Cruz, University of

62

Density hysteresis of heavy water confined in a nanoporous silica matrix  

E-Print Network [OSTI]

Density hysteresis of heavy water confined in a nanoporous silica matrix Yang Zhanga,b , Antonio of heavy water confined in a nanoporous silica matrix in a temperature-pressure range, from 300 to 130 K in the relevant phase region. More- over, the density data we obtained for the confined heavy water under

Chen, Sow-Hsin

63

Heavy oil production from Alaska  

SciTech Connect (OSTI)

North Slope of Alaska has an estimated 40 billion barrels of heavy oil and bitumen in the shallow formations of West Sak and Ugnu. Recovering this resource economically is a technical challenge for two reasons: (1) the geophysical environment is unique, and (2) the expected recovery is a low percentage of the oil in place. The optimum advanced recovery process is still undetermined. Thermal methods would be applicable if the risks of thawing the permafrost can be minimized and the enormous heat losses reduced. Use of enriched natural gas is a probable recovery process for West Sak. Nearby Prudhoe Bay field is using its huge natural gas resources for pressure maintenance and enriched gas improved oil recovery (IOR). Use of carbon dioxide is unlikely because of dynamic miscibility problems. Major concerns for any IOR include close well spacing and its impact on the environment, asphaltene precipitation, sand production, and fines migration, in addition to other more common production problems. Studies have indicated that recovering West Sak and Lower Ugnu heavy oil is technically feasible, but its development has not been economically viable so far. Remoteness from markets and harsh Arctic climate increase production costs relative to California heavy oil or Central/South American heavy crude delivered to the U.S. Gulf Coast. A positive change in any of the key economic factors could provide the impetus for future development. Cooperation between the federal government, state of Alaska, and industry on taxation, leasing, and permitting, and an aggressive support for development of technology to improve economics is needed for these heavy oil resources to be developed.

Mahmood, S.M.; Olsen, D.K. [NIPER/BDM-Oklahoma, Inc., Bartlesville, OK (United States); Thomas, C.P. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

1995-12-31T23:59:59.000Z

64

CHARACTERIZATION OF RADIOACTIVITY IN THE REACTOR VESSEL OF THE HEAVY WATER COMPONENT TEST REACTOR  

SciTech Connect (OSTI)

The Heavy Water Component Test Reactor (HWCTR) facility is a pressurized heavy water reactor that was used to test candidate fuel designs for heavy water power reactors. The reactor operated at nominal power of 50 MW{sub th}. The reactor coolant loop operated at 1200 psig and 250 C. Two isolated test loop were designed into the reactor to provide special test conditions. Fig. 1 shows a cut-away view of the reactor. The two loops are contained in four inch diameter stainless steel piping. The HWCTR was operated for only a short duration, from March 1962 to December 1964 in order to test the viability of test fuel elements and other reactor components for use in a heavy water power reactor. The reactor achieved 13,882 MWd of total power while testing 36 different fuel assemblies. In the course of operation, HWCTR experienced the cladding failures of 10 separate test fuel assemblies. In each case, the cladding was breached with some release of fuel core material into the isolated test loop, causing fission product and actinide contamination in the main coolant loop and the liquid and boiling test loops. Despite the contribution of the contamination from the failed fuel, the primary source of radioactivity in the HWCTR vessel and internals is the activation products in the thermal shields, and to a lesser degree, activation products in the reactor vessel walls and liner. A detailed facility characterization report of the HWCTR facility was completed in 1996. Many of the inputs and assumptions in the 1996 characterization report were derived from the HWCTR decommissioning plan published in 1975. The current paper provides an updated assessment of the radioisotopic characteristics of the HWCTR vessel and internals to support decommissioning activities on the facility.

Vinson, Dennis

2010-06-01T23:59:59.000Z

65

Wall-collision line broadening of molecular oxygen within nanoporous materials  

SciTech Connect (OSTI)

Wall-collision broadening of near-infrared absorption lines of molecular oxygen confined in nanoporous zirconia is studied by employing high-resolution diode-laser spectroscopy. The broadening is studied for pores of different sizes under a range of pressures, providing new insights on how wall collisions and intermolecular collisions influence the total spectroscopic line profile. The pressure series show that wall-collision broadening is relatively more prominent under reduced pressures, enabling sensitive means to probe pore sizes of porous materials. In addition, we show that the total wall-collision-broadened profile strongly deviates from a Voigt profile and that wall-collision broadening exhibits an additive-like behavior to the pressure and Doppler broadening.

Xu, Can T.; Lewander, Maerta; Andersson-Engels, Stefan; Svensson, Tomas; Svanberg, Sune [Department of Physics, Lund University, P. O. Box 118, SE-221 00 Lund (Sweden); Adolfsson, Erik [Ceramic Materials, SWEREA IVF, Box 104, SE-431 22 Moelndal (Sweden)

2011-10-15T23:59:59.000Z

66

Thermal treatment wall  

DOE Patents [OSTI]

A thermal treatment wall emplaced to perform in-situ destruction of contaminants in groundwater. Thermal destruction of specific contaminants occurs by hydrous pyrolysis/oxidation at temperatures achievable by existing thermal remediation techniques (electrical heating or steam injection) in the presence of oxygen or soil mineral oxidants, such as MnO.sub.2. The thermal treatment wall can be installed in a variety of configurations depending on the specific objectives, and can be used for groundwater cleanup, wherein in-situ destruction of contaminants is carried out rather than extracting contaminated fluids to the surface, where they are to be cleaned. In addition, the thermal treatment wall can be used for both plume interdiction and near-wellhead in-situ groundwater treatment. Thus, this technique can be utilized for a variety of groundwater contamination problems.

Aines, Roger D. (Livermore, CA); Newmark, Robin L. (Livermore, CA); Knauss, Kevin G. (Livermore, CA)

2000-01-01T23:59:59.000Z

67

Modelling of a coke oven heating wall M. Landreau, D. Isler, Centre de Pyrolyse de Marienau (CPM)  

E-Print Network [OSTI]

- 1 - Modelling of a coke oven heating wall M. Landreau, D. Isler, Centre de Pyrolyse de Marienau with thermomechanical modelling of a coke oven heating wall. The objective is to define the safe limits of coke oven of walls, roof and larry car, pre-stresses (anchoring system), lateral pressure due to coal pushing A 3D

Boyer, Edmond

68

Subcooled Boiling Near a Heated Wall  

SciTech Connect (OSTI)

Experimental measurements of void fraction, bubble frequency, and velocity are obtained in subcooled R-134a flowing over a heated flat plate near an unheated wall and compared to analytical predictions. The measurements were obtained for a fixed system pressure and mass flow rate (P = 2.4 MPa and w = 106 kg/hr) at various inlet liquid temperatures. During the experiments, electrical power was applied at a constant rate to one side of the test section. The local void fraction data, acquired with a hot-film anemometer probe, showed the existence of a significant peak near the heated wall and a smaller secondary peak near the unheated wall for the larger inlet subcoolings. Local vapor velocity data, taken with the hot-film probe and a laser Doppler velocimeter, showed broad maxima near the centerline between the heated and unheated plates. Significant temperature gradients near the heated wall were observed for large inlet subcooling. Bubble size data, inferred from measurements of void fraction, bubble frequency and vapor velocity, when combined with the measured bubble chord length distributions illustrate the transition from pure three dimensional spherical to two-dimensional planar bubble flow, the latter being initiated when the bubbles fill the gap between the plates. These various two-phase flow measurements were used for development of a multidimensional, four-field calculational method; comparisons of the data to the calculations show reasonable agreement.

T.A. Trabold; C.C. Maneri; P.F. Vassallo; D.M. Considine

2000-10-27T23:59:59.000Z

69

A coupled neutronics/thermalhydraulics tool for calculating fluctuations in Pressurized Water Reactors  

E-Print Network [OSTI]

Water Reactors or Heavy Water Reactors (LarssoA coupled neutronics/thermal­hydraulics tool for calculating fluctuations in Pressurized Water in neutron flux, fuel temperature, moderator den- sity and flow velocity in Pressurized Water Reactors

Demazière, Christophe

70

Single-Walle 4. Single-Walled Carbon Nanotubes  

E-Print Network [OSTI]

applications, carbon nanotube research is ac- tively being pursued in diverse areas including energy storage105 Single-Walle 4. Single-Walled Carbon Nanotubes Sebastien Nanot, Nicholas A. Thompson, Ji Single-walled carbon nanotubes (SWCNTs) are hol- low, long cylinders with extremely large aspect ratios

Kono, Junichiro

71

High-R Walls for Remodeling: Wall Cavity Moisture Monitoring  

SciTech Connect (OSTI)

The focus of the study is on the performance of wall systems, and in particular, the moisture characteristics inside the wall cavity and in the wood sheathing. Furthermore, while this research will initially address new home construction, the goal is to address potential moisture issues in wall cavities of existing homes when insulation and air sealing improvements are made.

Wiehagen, J.; Kochkin, V.

2012-12-01T23:59:59.000Z

72

Bioconversion of Heavy oil.  

E-Print Network [OSTI]

??70 % of world?s oil reservoirs consist of heavy oil, and as the supply of conventional oil decreases, researchers are searching for new technologies to… (more)

Steinbakk, Sandra

2011-01-01T23:59:59.000Z

73

Neutron diffraction studies of water and aqueous solutions under pressure G. W. Neilson and S. Cummings  

E-Print Network [OSTI]

. Abstract 2014 A summary is given of data obtained from neutron diffraction experiments on heavy water pressures. In fact, the only neutron diffraction work we know of is that concemed with heavy water [5, 6]. (X-ray diffrac- tion experiments have, however, been carried out on water and heavy water

Boyer, Edmond

74

Integrating Biomechanics, Hemodynamics, and Vascular Adaptation to Relate Mechanisms of Vascular Adaptation to Arterial Pulsatile Pressure in Health and Disease  

E-Print Network [OSTI]

local changes in pulsatile blood pressures and flows lead to changes in local endothelial shear stress and circumferential wall stress. The field of mechanobiology has identified how local changes in wall circumferential stress and endothelial shear...

Nguyen, Phuc Hoang

2014-08-07T23:59:59.000Z

75

Earth pressures and deformations in civil infrastructure in expansive soils  

E-Print Network [OSTI]

This dissertation includes the three major parts of the study: volume change, and lateral earth pressure due to suction change in expansive clay soils, and design of civil infrastructure drilled pier, retaining wall and pavement in expansive soils...

Hong, Gyeong Taek

2008-10-10T23:59:59.000Z

76

Negative pressure characteristics of an evaporating meniscus at nanoscale  

E-Print Network [OSTI]

This study aims at understanding the characteristics of negative liquid pressures at the nanoscale using molecular dynamics simulation. A nano-meniscus is formed by placing liquid argon on a platinum wall between two ...

Maroo, Shalabh C.

2011-01-01T23:59:59.000Z

77

Water issues associated with heavy oil production.  

SciTech Connect (OSTI)

Crude oil occurs in many different forms throughout the world. An important characteristic of crude oil that affects the ease with which it can be produced is its density and viscosity. Lighter crude oil typically can be produced more easily and at lower cost than heavier crude oil. Historically, much of the nation's oil supply came from domestic or international light or medium crude oil sources. California's extensive heavy oil production for more than a century is a notable exception. Oil and gas companies are actively looking toward heavier crude oil sources to help meet demands and to take advantage of large heavy oil reserves located in North and South America. Heavy oil includes very viscous oil resources like those found in some fields in California and Venezuela, oil shale, and tar sands (called oil sands in Canada). These are described in more detail in the next chapter. Water is integrally associated with conventional oil production. Produced water is the largest byproduct associated with oil production. The cost of managing large volumes of produced water is an important component of the overall cost of producing oil. Most mature oil fields rely on injected water to maintain formation pressure during production. The processes involved with heavy oil production often require external water supplies for steam generation, washing, and other steps. While some heavy oil processes generate produced water, others generate different types of industrial wastewater. Management and disposition of the wastewater presents challenges and costs for the operators. This report describes water requirements relating to heavy oil production and potential sources for that water. The report also describes how water is used and the resulting water quality impacts associated with heavy oil production.

Veil, J. A.; Quinn, J. J.; Environmental Science Division

2008-11-28T23:59:59.000Z

78

Covering Walls With Fabrics.  

E-Print Network [OSTI]

the glue a dull surface to adhere to. Fill any gouges or nail holes with patching plaster and sand smooth after they have dried thoroughly. Minor ripples can be covered with spackling compound, a plaster-like substance that is spread thinly... during dry weather and in a well-ventilated room. Cut each panel 3 inches longer than the ceiling height. Match and cut sufficient fabric widths to cover completely one wall at a time. Start with Corner I nstall the first fabric panel so...

Anonymous,

1979-01-01T23:59:59.000Z

79

Poorly Draining Soil Reinforced with Geosynthetic with in Plane Drainage: Efficiency and Pore Pressure Behavior  

E-Print Network [OSTI]

drainage system contributes to the dissipation of porous pressure when the water content of the soil test, porous pressure 1 INTRODUCTION Sustainable technologies can be defined as the use of methods of cement is to build mechanically stabilized earth walls rather than concrete walls. Conventionally, freely

Zornberg, Jorge G.

80

Saltstone Osmotic Pressure  

SciTech Connect (OSTI)

Recent research into the moisture retention properties of saltstone suggest that osmotic pressure may play a potentially significant role in contaminant transport (Dixon et al., 2009 and Dixon, 2011). The Savannah River Remediation Closure and Disposal Assessments Group requested the Savannah River National Laboratory (SRNL) to conduct a literature search on osmotic potential as it relates to contaminant transport and to develop a conceptual model of saltstone that incorporates osmotic potential. This report presents the findings of the literature review and presents a conceptual model for saltstone that incorporates osmotic potential. The task was requested through Task Technical Request HLW-SSF-TTR-2013-0004. Simulated saltstone typically has very low permeability (Dixon et al. 2008) and pore water that contains a large concentration of dissolved salts (Flach and Smith 2013). Pore water in simulated saltstone has a high salt concentration relative to pore water in concrete and groundwater. This contrast in salt concentration can generate high osmotic pressures if simulated saltstone has the properties of a semipermeable membrane. Estimates of osmotic pressure using results from the analysis of pore water collected from simulated saltstone show that an osmotic pressure up to 2790 psig could be generated within the saltstone. Most semi-permeable materials are non-ideal and have an osmotic efficiency <1 and as a result actual osmotic pressures are less than theoretical pressures. Observations from laboratory tests of simulated saltstone indicate that it may exhibit the behavior of a semi-permeable membrane. After several weeks of back pressure saturation in a flexible wall permeameter (FWP) the membrane containing a simulated saltstone sample appeared to have bubbles underneath it. Upon removal from the FWP the specimen was examined and it was determined that the bubbles were due to liquid that had accumulated between the membrane and the sample. One possible explanation for the accumulation of solution between the membrane and sample is the development of osmotic pressure within the sample. Osmotic pressure will affect fluid flow and contaminant transport and may result in the changes to the internal structure of the semi-permeable material. B?nard et al. 2008 reported swelling of wet cured Portland cement mortars containing salts of NaNO{sub 3}, KNO{sub 3}, Na{sub 3}PO{sub 4}x12H {sub 2}O, and K{sub 3}PO{sub 4} when exposed to a dilute solution. Typically hydraulic head is considered the only driving force for groundwater in groundwater models. If a low permeability material containing a concentrated salt solution is present in the hydrogeologic sequence large osmotic pressures may develop and lead to misinterpretation of groundwater flow and solute transport. The osmotic pressure in the semi-permeable material can significantly impact groundwater flow in the vicinity of the semi-permeable material. One possible outcome is that groundwater will flow into the semi-permeable material resulting in hydrologic containment within the membrane. Additionally, hyperfiltration can occur within semi-permeable materials when water moves through a membrane into the more concentrated solution and dissolved constituents are retained in the lower concentration solution. Groundwater flow and transport equations that incorporate chemical gradients (osmosis) have been developed. These equations are referred to as coupled flow equations. Currently groundwater modeling to assess the performance of saltstone waste forms is conducted using the PORFLOW groundwater flow and transport model. PORFLOW does not include coupled flow from chemico-osmotic gradients and therefore numerical simulation of the effect of coupled flow on contaminant transport in and around saltstone cannot be assessed. Most natural semi-permeable membranes are non-ideal membranes and do not restrict all movement of solutes and as a result theoretical osmotic potential is not realized. Osmotic efficiency is a parameter in the coupled flow equation that accounts for the

Nichols, Ralph L.; Dixon, Kenneth L.

2013-09-23T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Process for removing heavy metal compounds from heavy crude oil  

DOE Patents [OSTI]

A process is provided for removing heavy metal compounds from heavy crude oil by mixing the heavy crude oil with tar sand; preheating the mixture to a temperature of about 650.degree. F.; heating said mixture to up to 800.degree. F.; and separating tar sand from the light oils formed during said heating. The heavy metals removed from the heavy oils can be recovered from the spent sand for other uses.

Cha, Chang Y. (Golden, CO); Boysen, John E. (Laramie, WY); Branthaver, Jan F. (Laramie, WY)

1991-01-01T23:59:59.000Z

82

Security Walls, LLC WIPP 2009  

Broader source: Energy.gov (indexed) [DOE]

Walls, LLC Waste Isolation Pilot Plant Department of Energy Voluntary Protection Program Onsite Review March 3-4, 2009 The Department of Energy (DOE) Voluntary Protection Program...

83

Heavy Hybrid mesons Masses  

E-Print Network [OSTI]

We estimate the ground state masses of the heavy hybrid mesons using a phenomenological QCD-type potential. 0^{- -},1^{- -},0^{- +},1^{- +} and 0^{+ -} J^{PC} states are considered.

F. Iddir; L. Semlala

2006-11-13T23:59:59.000Z

84

Liquid Walls Innovative Concepts for First Walls and Blankets  

E-Print Network [OSTI]

with existing technology · Size of plasma devices and power plants can be substantially reduced High PoloidalLiquid Walls Innovative Concepts for First Walls and Blankets Mohamed Abdou Professor, Mechanical as part of the US Restructured Fusion Program Strategy to enhance innovation · Natural Questions

Abdou, Mohamed

85

Oven wall panel construction  

DOE Patents [OSTI]

An oven roof or wall is formed from modular panels, each of which comprises an inner fabric and an outer fabric. Each such fabric is formed with an angle iron framework and somewhat resilient tie-bars or welded at their ends to flanges of the angle irons to maintain the inner and outer frameworks in spaced disposition while minimizing heat transfer by conduction and permitting some degree of relative movement on expansion and contraction of the module components. Suitable thermal insulation is provided within the module. Panels or skins are secured to the fabric frameworks and each such skin is secured to a framework and projects laterally so as slidingly to overlie the adjacent frame member of an adjacent panel in turn to permit relative movement during expansion and contraction.

Ellison, Kenneth (20 Avondale Cres., Markham, CA); Whike, Alan S. (R.R. #1, Caledon East, both of Ontario, CA)

1980-04-22T23:59:59.000Z

86

J/psi production and elliptic flow in relativistic heavy-ion collisions  

E-Print Network [OSTI]

upsilon(2) of J/psi in relativistic heavy-ion collisions. For the expansion dynamics of produced hot, dense matter, we introduce a schematic fireball model with its transverse acceleration determined from the pressure gradient inside the fireball...

Song, Taesoo; Ko, Che Ming; Lee, Su Houng; Xu, Jun.

2011-01-01T23:59:59.000Z

87

Research on Oil Recovery Mechanisms in Heavy Oil Reservoirs  

SciTech Connect (OSTI)

The goal of this project is to increase recovery of heavy oils. Towards that goal studies are being conducted in how to assess the influence of temperature and pressure on the absolute and relative permeability to oil and water and on capillary pressure; to evaluate the effect of different reservoir parameters on the in site combustion process; to develop and understand mechanisms of surfactants on for the reduction of gravity override and channeling of steam; and to improve techniques of formation evaluation.

Louis M. Castanier; William E. Brigham

1998-03-31T23:59:59.000Z

88

Product Sheet Wall Mount Lift  

E-Print Network [OSTI]

Product Sheet Wall Mount Lift Ergotron® Neo-FlexTM 870-05-061, rev. 12/11/07 www. Less effort. Feel the difference. Add greater range of movement to your LCD display or TV with the Neo-Flex Wall Mount Lift! CF patented lift-and-pivot motion technology adjusts with a light touch. Raise

Saskatchewan, University of

89

Moisture Research - Optimizing Wall Assemblies  

SciTech Connect (OSTI)

The Consortium for Advanced Residential Buildings (CARB) evaluated several different configurations of wall assemblies to determine the accuracy of moisture modeling and make recommendations to ensure durable, efficient assemblies. WUFI and THERM were used to model the hygrothermal and heat transfer characteristics of these walls.

Arena, L.; Mantha, P.

2013-05-01T23:59:59.000Z

90

Enhanced Heavy Oil Recovery by Emulsification With Injected Nanoparticles  

E-Print Network [OSTI]

emulsifying the immobile heavy oil, and transports it out of the reservoir as a low viscosity fluid. Generating the emulsions in the reservoir was suggested because it offers numerous advantages. The first advantage is low injectivity pressures due to the low...

Martinez Cedillo, Arturo Rey

2013-11-26T23:59:59.000Z

91

Co-processing of heavy oil  

SciTech Connect (OSTI)

In co-processing of petroleum and coal, the petroleum fraction may serve as the {open_quotes}liquefaction solvent,{close_quotes} or hydrogen donor, and the aromatics present in the coal liquid may serve as hydrogen {open_quotes}shuttlers{close_quotes} by efficiently transferring hydrogen moieties to places where they are most deficient. The important advantages of co-processing include the following: (1) upgrading of heavy petroleum in a reaction with coal and (2) conversion of coal to synthetic crudes which could be further upgraded to a premium liquid fuel. Co-processing of coal with petroleum, heavy crudes, and residues through catalytic hydrogenation or solvent extraction have been extensively investigated. The studies were typically conducted in the temperature range of 450{degrees}-500{degrees}C under pressurized hydrogen; catalysts are generally also added for hydroconversion of the feedstocks. However, relatively little has been reported in the literature regarding co-processing of coal with heavy petroleum by simple pyrolysis. In this study, co-processing of heavy oil and coal at relatively middle conditions was conducted without the complicating influences of pressurized hydrogen or catalysts. The resulted demonstrate that there is a synergism during co-processing of petroleum and coal. This synergism enhances both the yield and quality of the liquid products. In general, liquids from co-processing the mixture contain a higher content of alkane/alkene, neutral aromatics, lower content of monophenols, and other oxygen containing compounds as compared to the liquids from coal alone. The liquid from the mixture also contains a higher content of naphthenic carbon and naphthenic rings/molecules than those from coal liquid. This suggests that the product from the mixture can be easily upgraded to a premium quality fuel.

Khan, M.R. [Texaco Research and Development, Beacon, NY (United States)

1995-12-31T23:59:59.000Z

92

Heavy-Section Steel Irradiation Program  

SciTech Connect (OSTI)

Maintaining the integrity of the reactor pressure vessel (RPV) in a light-water-cooled nuclear power plant is crucial in preventing and controlling severe accidents that have the potential for major contamination release. Because the RPV is the only key safety-related component of the plant for which a redundant backup system does not exist, it is imperative to fully understand the degree of irradiation-induced degradation of the RPV's fracture resistance that occurs during service. For this reason, the Heavy-Section Steel Irradiation (HSSI) Program has been established.

Rosseel, T.M.

2000-04-01T23:59:59.000Z

93

Exploiting heavy oil reserves  

E-Print Network [OSTI]

North Sea investment potential Exploiting heavy oil reserves Beneath the waves in 3D Aberdeen.hamptonassociates.com pRINTED BY nB GroUP Paper sourced from sustainable forests CONTENTS 3/5 does the north Sea still industry partnership drives research into sensor systems 11 Beneath the waves in 3d 12/13 does

Levi, Ran

94

PHYTOEXTRACTION OF HEAVY METALS  

E-Print Network [OSTI]

) Type of phytoremediation Cost effective form of environmental remediation (Glass 1999) Chelating Agents: desorb heavy metals from soil matrix and form water-soluble metal complexes (Shen et al -using hyperaccumulator plant biomass to produce a bio-ore for commercial use -Li et al. look at using Ni

Blouin-Demers, Gabriel

95

Review of Heavy-ion Induced Desorption Studies for Particle Accelerators  

E-Print Network [OSTI]

During high-intensity heavy-ion operation of several particle accelerators worldwide, large dynamic pressure rises of orders of magnitude were caused by lost beam ions that impacted under grazing angle onto the vacuum chamber walls. This ion-induced desorption, observed, for example, at CERN, GSI, and BNL, can seriously limit the ion intensity, luminosity, and beam lifetime of the accelerator. For the heavyion program at CERN's Large Hadron Collider collisions between beams of fully stripped lead (208Pb82+) ions with a beam energy of 2.76 TeV/u and a nominal luminosity of 10**27 cm**-2 s**-1 are foreseen. The GSI future project FAIR (Facility for Antiproton and Ion Research) aims at a beam intensity of 10**12 uranium (238U28+) ions per second to be extracted from the synchrotron SIS18. Over the past years an experimental effort has been made to study the observed dynamic vacuum degradations, which are important to understand and overcome for present and future particle accelerators. The paper reviews the resu...

Mahner, E

2008-01-01T23:59:59.000Z

96

DefectDomain Wall Interactions in Trigonal  

E-Print Network [OSTI]

Defect­Domain Wall Interactions in Trigonal Ferroelectrics Venkatraman Gopalan,1 Volkmar Dierolf,2 walls in the trigonal ferroelectrics lithium niobate and lithium tantalate. It is shown that extrinsic questions re- garding intrinsic widths, defect­domain wall interactions, and static versus dynamic wall

Gopalan, Venkatraman

97

PHENIX recent heavy flavor results  

E-Print Network [OSTI]

Cold nuclear matter (CNM) effects provide an important baseline for the interpretation of data in heavy ion collisions. Such effects include nuclear shadowing, Cronin effect, and initial patron energy loss, and it is interesting to study the dependence on impact parameter and kinematic region. Heavy quark production is a good measurement to probe the CNM effects particularly on gluons, since heavy quarks are mainly produced via gluon fusions at RHIC energy. The PHENIX experiment has experiment has ability to study the CNM effects by measuring heavy quark production in $d$$+$Au collisions at variety of kinematic ranges. Comparisons of heavy quark production at different rapidities allow us to study modification of gluon density function in the Au nucleus depending on momentum fraction. Furthermore, comparisons to the results from heavy ion collisions (Au$+$Au and Cu$+$Cu) measured by PHENIX provide insight into the role of CNM effects in such collisions. Recent PHENIX results on heavy quark production are discussed.

Sanghoon Lim for the PHENIX collaboration

2014-02-28T23:59:59.000Z

98

Continuous growth of single-wall carbon nanotubes using chemical vapor deposition  

DOE Patents [OSTI]

The invention relates to a chemical vapor deposition process for the continuous growth of a carbon single-wall nanotube where a carbon-containing gas composition is contacted with a porous membrane and decomposed in the presence of a catalyst to grow single-wall carbon nanotube material. A pressure differential exists across the porous membrane such that the pressure on one side of the membrane is less than that on the other side of the membrane. The single-wall carbon nanotube growth may occur predominately on the low-pressure side of the membrane or, in a different embodiment of the invention, may occur predominately in between the catalyst and the membrane. The invention also relates to an apparatus used with the carbon vapor deposition process.

Grigorian, Leonid; Hornyak, Louis; Dillon, Anne C; Heben, Michael J

2014-09-23T23:59:59.000Z

99

Continuous growth of single-wall carbon nanotubes using chemical vapor deposition  

DOE Patents [OSTI]

The invention relates to a chemical vapor deposition process for the continuous growth of a carbon single-wall nanotube where a carbon-containing gas composition is contacted with a porous membrane and decomposed in the presence of a catalyst to grow single-wall carbon nanotube material. A pressure differential exists across the porous membrane such that the pressure on one side of the membrane is less than that on the other side of the membrane. The single-wall carbon nanotube growth may occur predominately on the low-pressure side of the membrane or, in a different embodiment of the invention, may occur predominately in between the catalyst and the membrane. The invention also relates to an apparatus used with the carbon vapor deposition process.

Grigorian, Leonid (Raymond, OH); Hornyak, Louis (Evergreen, CO); Dillon, Anne C (Boulder, CO); Heben, Michael J (Denver, CO)

2008-10-07T23:59:59.000Z

100

Turbine airfoil with outer wall thickness indicators  

DOE Patents [OSTI]

A turbine airfoil usable in a turbine engine and including a depth indicator for determining outer wall blade thickness. The airfoil may include an outer wall having a plurality of grooves in the outer surface of the outer wall. The grooves may have a depth that represents a desired outer surface and wall thickness of the outer wall. The material forming an outer surface of the outer wall may be removed to be flush with an innermost point in each groove, thereby reducing the wall thickness and increasing efficiency. The plurality of grooves may be positioned in a radially outer region of the airfoil proximate to the tip.

Marra, John J; James, Allister W; Merrill, Gary B

2013-08-06T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Support pedestals for interconnecting a cover and nozzle band wall in a gas turbine nozzle segment  

DOE Patents [OSTI]

A gas turbine nozzle segment has outer and inner band portions. Each band portion includes a nozzle wall, a cover and an impingement plate between the cover and nozzle wall defining two cavities on opposite sides of the impingement plate. Cooling steam is supplied to one cavity for flow through the apertures of the impingement plate to cool the nozzle wall. Structural pedestals interconnect the cover and nozzle wall and pass through holes in the impingement plate to reduce localized stress otherwise resulting from a difference in pressure within the chamber of the nozzle segment and the hot gas path and the fixed turbine casing surrounding the nozzle stage. The pedestals may be cast or welded to the cover and nozzle wall.

Yu, Yufeng Phillip (Simpsonville, SC); Itzel, Gary Michael (Simpsonville, SC); Webbon, Waylon Willard (Greenville, SC); Bagepalli, Radhakrishna (Schenectady, NY); Burdgick, Steven Sebastian (Schenectady, NY); Kellock, Iain Robertson (Simpsonville, SC)

2002-01-01T23:59:59.000Z

102

MHD Electrode and wall constructions  

DOE Patents [OSTI]

Electrode and wall constructions for the walls of a channel transmitting the hot plasma in a magnetohydrodynamic generator. The electrodes and walls are made of a plurality of similar modules which are spaced from one another along the channel. The electrodes can be metallic or ceramic, and each module includes one or more electrodes which are exposed to the plasma and a metallic cooling bar which is spaced from the plasma and which has passages through which a cooling fluid flows to remove heat transmitted from the electrode to the cooling bar. Each electrode module is spaced from and electrically insulated from each adjacent module while interconnected by the cooling fluid which serially flows among selected modules. A wall module includes an electrically insulating ceramic body exposed to the plasma and affixed, preferably by mechanical clips or by brazing, to a metallic cooling bar spaced from the plasma and having cooling fluid passages. Each wall module is, similar to the electrode modules, electrically insulated from the adjacent modules and serially interconnected to other modules by the cooling fluid.

Way, Stewart (Columbia, MD); Lempert, Joseph (Penn Hills, PA)

1984-01-01T23:59:59.000Z

103

Utah Heavy Oil Program  

SciTech Connect (OSTI)

The Utah Heavy Oil Program (UHOP) was established in June 2006 to provide multidisciplinary research support to federal and state constituents for addressing the wide-ranging issues surrounding the creation of an industry for unconventional oil production in the United States. Additionally, UHOP was to serve as an on-going source of unbiased information to the nation surrounding technical, economic, legal and environmental aspects of developing heavy oil, oil sands, and oil shale resources. UHOP fulGilled its role by completing three tasks. First, in response to the Energy Policy Act of 2005 Section 369(p), UHOP published an update report to the 1987 technical and economic assessment of domestic heavy oil resources that was prepared by the Interstate Oil and Gas Compact Commission. The UHOP report, entitled 'A Technical, Economic, and Legal Assessment of North American Heavy Oil, Oil Sands, and Oil Shale Resources' was published in electronic and hard copy form in October 2007. Second, UHOP developed of a comprehensive, publicly accessible online repository of unconventional oil resources in North America based on the DSpace software platform. An interactive map was also developed as a source of geospatial information and as a means to interact with the repository from a geospatial setting. All documents uploaded to the repository are fully searchable by author, title, and keywords. Third, UHOP sponsored Give research projects related to unconventional fuels development. Two projects looked at issues associated with oil shale production, including oil shale pyrolysis kinetics, resource heterogeneity, and reservoir simulation. One project evaluated in situ production from Utah oil sands. Another project focused on water availability and produced water treatments. The last project considered commercial oil shale leasing from a policy, environmental, and economic perspective.

J. Bauman; S. Burian; M. Deo; E. Eddings; R. Gani; R. Goel; C.K. Huang; M. Hogue; R. Keiter; L. Li; J. Ruple; T. Ring; P. Rose; M. Skliar; P.J. Smith; J.P. Spinti; P. Tiwari; J. Wilkey; K. Uchitel

2009-10-20T23:59:59.000Z

104

Unusual Phase Behavior of Confined Heavy Water  

E-Print Network [OSTI]

Many of the anomalous properties of water are amplified in the deeply supercooled region. Here we present neutron scattering measurements of the density of heavy water confined in a nanoporous silica matrix MCM-41-S (\\approx15 {\\AA} pore diameter), namely, the equation of state {\\rho}(T,P), in a temperature-pressure range, from 300 K to 130 K and from 1 bar to 2900 bar, where bulk water will crystalize. A sudden change of slope in the otherwise continuous density profile (a "kink") is observed below a certain pressure Pc; however, this feature is absent above Pc. Instead, a hysteresis phenomenon in the density profiles between the warming and cooling scans becomes prominent above Pc. Hence, the data can be interpreted as a line of apparent 2nd-order phase transition at low pressures evolving into a line of 1st-order phase transition at high pressures. If so, the existence of a "tricritical point" at Pc \\approx 1500 bar, Tc \\approx 210 K becomes another possible scenario to explain the exceptionally rich phase behavior of low-temperature confined water.

Yang Zhang; Antonio Faraone; William A. Kamitakahara; Kao-Hsiang Liu; Chung-Yuan Mou; Juscelino B. Leão; Sung Chang; Sow-Hsin Chen

2011-06-21T23:59:59.000Z

105

Heavy Ion Inertial Fusion Energy: Summaries of Program Elements  

SciTech Connect (OSTI)

The goal of the Heavy Ion Fusion (HIF) Program is to apply high-current accelerator technology to IFE power production. Ion beams of mass {approx}100 amu and kinetic energy {>=} 1 GeV provide efficient energy coupling into matter, and HIF enjoys R&D-supported favorable attributes of: (1) the driver, projected to be robust and efficient; see 'Heavy Ion Accelerator Drivers.'; (2) the targets, which span a continuum from full direct to full indirect drive (and perhaps fast ignition), and have metal exteriors that enable injection at {approx}10 Hz; see 'IFE Target Designs'; (3) the near-classical ion energy deposition in the targets; see 'Beam-Plasma Interactions'; (4) the magnetic final lens, robust against damage; see 'Final Optics-Heavy Ion Beams'; and (5) the fusion chamber, which may use neutronically-thick liquids; see 'Liquid-Wall Chambers.' Most studies of HIF power plants have assumed indirect drive and thick liquid wall protection, but other options are possible.

Friedman, A; Barnard, J J; Kaganovich, I; Seidl, P A; Briggs, R J; Faltens, A; Kwan, J W; Lee, E P; Logan, B G

2011-02-28T23:59:59.000Z

106

Modeling chamber transport for heavy-ion fusion  

SciTech Connect (OSTI)

In a typical thick-liquid-wall scenario for heavy-ion fusion (HIF), between seventy and two hundred high-current beams enter the target chamber through ports and propagate about three meters to the target. Since molten-salt jets are planned to protect the chamber wall, the beams move through vapor from the jets, and collisions between beam ions and this background gas both strip the ions and ionize the gas molecules. Radiation from the preheated target causes further beam stripping and gas ionization. Due to this stripping, beams for heavy-ion fusion are expected to require substantial neutralization in a target chamber. Much recent research has, therefore, focused on beam neutralization by electron sources that were neglected in earlier simulations, including emission from walls and the target, photoionization by the target radiation, and pre-neutralization by a plasma generated along the beam path. When these effects are included in simulations with practicable beam and chamber parameters, the resulting focal spot is approximately the size required by a distributed radiator target.

Sharp, W.M.; Callahan, D.A.; Tabak, M.; Yu, S.S.; Peterson, P.F.; Welch, D.R.; Rose, D.V.; Olson, C.L.

2002-10-01T23:59:59.000Z

107

Domain walls riding the wave.  

SciTech Connect (OSTI)

Recent years have witnessed a rapid proliferation of electronic gadgets around the world. These devices are used for both communication and entertainment, and it is a fact that they account for a growing portion of household energy consumption and overall world consumption of electricity. Increasing the energy efficiency of these devices could have a far greater and immediate impact than a gradual switch to renewable energy sources. The advances in the area of spintronics are therefore very important, as gadgets are mostly comprised of memory and logic elements. Recent developments in controlled manipulation of magnetic domains in ferromagnet nanostructures have opened opportunities for novel device architectures. This new class of memories and logic gates could soon power millions of consumer electronic devices. The attractiveness of using domain-wall motion in electronics is due to its inherent reliability (no mechanical moving parts), scalability (3D scalable architectures such as in racetrack memory), and nonvolatility (retains information in the absence of power). The remaining obstacles in widespread use of 'racetrack-type' elements are the speed and the energy dissipation during the manipulation of domain walls. In their recent contribution to Physical Review Letters, Oleg Tretiakov, Yang Liu, and Artem Abanov from Texas A&M University in College Station, provide a theoretical description of domain-wall motion in nanoscale ferromagnets due to the spin-polarized currents. They find exact conditions for time-dependent resonant domain-wall movement, which could speed up the motion of domain walls while minimizing Ohmic losses. Movement of domain walls in ferromagnetic nanowires can be achieved by application of external magnetic fields or by passing a spin-polarized current through the nanowire itself. On the other hand, the readout of the domain state is done by measuring the resistance of the wire. Therefore, passing current through the ferromagnetic wire is the preferred method, as it combines manipulation and readout of the domain-wall state. The electrons that take part in the process of readout and manipulation of the domain-wall structure in the nanowire do so through the so-called spin transfer torque: When spin-polarized electrons in the ferromagnet nanowire pass through the domain wall they experience a nonuniform magnetization, and they try to align their spins with the local magnetic moments. The force that the electrons experience has a reaction force counterpart that 'pushes' the local magnetic moments, resulting in movement of the domain wall in the direction of the electron flow through the spin-transfer torque. The forces between the electrons and the local magnetic moments in the ferromagnet also create additional electrical resistance for the electrons passing through the domain wall. By measuring resistance across a segment of the nanowire, one determines if a domain wall is present; i.e., one can read the stored information. The interaction of the spin-polarized electrons with the domain wall in the ferromagnetic nanowire is not very efficient. Even for materials achieving high polarization of the free electrons, it is very difficult to move the magnetic domain wall. Several factors contribute to this problem, with imperfections of the ferromagnetic nanowire that cause domain-wall pinning being the dominant one. Permalloy nanowires, one of the best candidates for domain-wall-based memory and logic devices, require current densities of the order of 10{sup 8} A/cm{sup 2} in order to move a domain wall from a pinning well. Considering that this current has to pass through a relatively long wire, it is not very difficult to imagine that most of the energy will go to Joule heating. The efficiency of the process - the ratio of the energy converted to domain-wall motion to the total energy consumed - is comparable to that of an incandescent light bulb converting electricity to light. A step towards more efficient domain-wall-based memory devices is the advance of using alternating currents or curren

Karapetrov, G.; Novosad, V.; Materials Science Division

2010-11-01T23:59:59.000Z

108

Nuclear Science--A Guide to the Nuclear Science Wall Chart 2003 Contemporary Physics Education Project (CPEP)  

E-Print Network [OSTI]

Nuclear Science--A Guide to the Nuclear Science Wall Chart ©2003 Contemporary Physics Education Project (CPEP) 7-1 Chapter 7 Nuclear Reactions Nuclear reactions and nuclear scattering are used, protons, alphas, or "heavy ions"), creates these reactions when they strike a target nucleus. Nuclear

109

Domain Walls, Triples and Acceleration  

E-Print Network [OSTI]

We present a construction of domain walls in string theory. The domain walls can bridge both Minkowski and AdS string vacua. A key ingredient in the construction are novel classical Yang-Mills configurations, including instantons, which interpolate between toroidal Yang-Mills vacua. Our construction provides a concrete framework for the study of inflating metrics in string theory. In some cases, the accelerating space-time comes with a holographic description. The general form of the holographic dual is a field theory with parameters that vary over space-time.

Travis Maxfield; Savdeep Sethi

2014-04-09T23:59:59.000Z

110

Light Emission of Argon Discharges: Importance of Heavy Particle Processes  

SciTech Connect (OSTI)

Simulation studies on argon glow discharges established between flat disc electrodes, at pressure x electrode separation (pd) of 45 Pa cm are reported, with special attention to heavy-particle processes including excitation-induced light emission. The discharges are investigated through self-consistent hybrid modelling, consisting of a fluid description for components near local hydrodynamic equilibrium (slow electrons and ions), and Monte Carlo treatment of energetic electrons and heavy particles (ions and neutral atoms). The light emission profiles are analyzed for a wide range of operating conditions. The numerical results for the relative intensities and the shapes of the negative glow (created by electron impact excitation) and the cathode glow (created by heavy particle impact excitation) are in good agreement with experimental data obtained by Maric et al.

Hartmann, Peter [Research Institute for Solid State Physics and Optics, Hungarian Academy of Sciences, POB 49, H-1525 Budapest (Hungary)

2004-12-01T23:59:59.000Z

111

Radial elasticity of multi-walled boron nitride nanotubes  

SciTech Connect (OSTI)

We investigated the radial mechanical properties of multi-walled boron nitride nanotubes (MW-BNNTs) using atomic force microscopy. The employed MW-BNNTs were synthesized using pressurized vapor/condenser (PVC) methods and were dispersed in aqueous solution using ultrasonication methods with the aid of ionic surfactants. Our nanomechanical measurements reveal the elastic deformational behaviors of individual BNNTs with two to four tube walls in their transverse directions. Their effective radial elastic moduli were obtained through interpreting their measured radial deformation profiles using Hertzian contact mechanics models. Our results capture the dependences of the effective radial moduli of MW-BNNTs on both the tube outer diameter and the number of tube layers. The effective radial moduli of double-walled BNNTs are found to be several-fold higher than those of single-walled BNNTs within the same diameter range. Our work contributes directly to a complete understanding of the fundamental structural and mechanical properties of BNNTs and the pursuits of their novel structural and electronics applications.

Michael W. Smith, Cheol Park, Meng Zheng, Changhong Ke ,In-Tae Bae, Kevin Jordan

2012-02-01T23:59:59.000Z

112

Transpiring wall supercritical water oxidation reactor salt deposition studies  

SciTech Connect (OSTI)

Sandia National Laboratories has teamed with Foster Wheeler Development Corp. and GenCorp, Aerojet to develop and evaluate a new supercritical water oxidation reactor design using a transpiring wall liner. In the design, pure water is injected through small pores in the liner wall to form a protective boundary layer that inhibits salt deposition and corrosion, effects that interfere with system performance. The concept was tested at Sandia on a laboratory-scale transpiring wall reactor that is a 1/4 scale model of a prototype plant being designed for the Army to destroy colored smoke and dye at Pine Bluff Arsenal in Arkansas. During the tests, a single-phase pressurized solution of sodium sulfate (Na{sub 2}SO{sub 4}) was heated to supercritical conditions, causing the salt to precipitate out as a fine solid. On-line diagnostics and post-test observation allowed us to characterize reactor performance at different flow and temperature conditions. Tests with and without the protective boundary layer demonstrated that wall transpiration provides significant protection against salt deposition. Confirmation tests were run with one of the dyes that will be processed in the Pine Bluff facility. The experimental techniques, results, and conclusions are discussed.

Haroldsen, B.L.; Mills, B.E.; Ariizumi, D.Y.; Brown, B.G. [and others

1996-09-01T23:59:59.000Z

113

Steel-framed buildings: Impacts of wall detail configurations on the whole wall thermal performance  

SciTech Connect (OSTI)

The main objective of this paper is the influence of architectural wall details on the whole wall thermal performance. Whole wall thermal performance analysis was performed for six light gage steel-framed wall systems (some with wood components). For each wall system, all wall details were simulated using calibrated 3-D finite difference computer modeling. The thermal performance of the six steel-framed wall systems included various system details and the whole wall system thermal performance for a typical single-story ranch house. Currently, predicted heat losses through building walls are typically based on measurements of the wall system clear wall area using test methods such as ASTM C 236 or are calculated by one of the procedures recommended in the ASHRAE Handbook of Fundamentals that often is carried out for the clear wall area exclusively. In this paper, clear wall area is defined as the part of the wall system that is free of thermal anomalies due to building envelope details or thermally unaffected by intersections with other surfaces of the building envelope. Clear wall experiments or calculations normally do not include the effects of building envelope details such as corners, window and door openings, and structural intersections with roofs, floors, ceilings, and other walls. In steel-framed wall systems, these details typically consist of much more structural components than the clear wall. For this situation, the thermal properties measured or calculated for the clear wall area do not adequately represent the total wall system thermal performance. Factors that would impact the ability of today`s standard practice to accurately predict the total wall system thermal performance are the accuracy of the calculation methods, the area of the total wall that is clear wall, and the quantity and thermal performance of the various wall system details.

Kosny, J.; Desjarlais, A.O.; Christian, J.E.

1998-06-01T23:59:59.000Z

114

INL '@work' heavy equipment mechanic  

ScienceCinema (OSTI)

INL's Cad Christensen is a heavy equipment mechanic. For more information about INL careers, visit http://www.facebook.com/idahonationallaboratory.

Christensen, Cad

2013-05-28T23:59:59.000Z

115

Creation and Testing of the ACES Heavy Heavy-Duty Diesel Engine...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Creation and Testing of the ACES Heavy Heavy-Duty Diesel Engine Test Schedule for Representative Measurement of Heavy-Duty Engine Emissions Creation and Testing of the ACES Heavy...

116

Method and apparatus for coupling seismic sensors to a borehole wall  

DOE Patents [OSTI]

A method and apparatus suitable for coupling seismic or other downhole sensors to a borehole wall in high temperature and pressure environments. In one embodiment, one or more metal bellows mounted to a sensor module are inflated to clamp the sensor module within the borehole and couple an associated seismic sensor to a borehole wall. Once the sensing operation is complete, the bellows are deflated and the sensor module is unclamped by deflation of the metal bellows. In a further embodiment, a magnetic drive pump in a pump module is used to supply fluid pressure for inflating the metal bellows using borehole fluid or fluid from a reservoir. The pump includes a magnetic drive motor configured with a rotor assembly to be exposed to borehole fluid pressure including a rotatable armature for driving an impeller and an associated coil under control of electronics isolated from borehole pressure.

West, Phillip B.

2005-03-15T23:59:59.000Z

117

OXFORD BIBLIOGRAPHIES IN ECOLOGY "HEAVY METAL TOLERANCE"  

E-Print Network [OSTI]

cellular mechanisms affected by heavy metals is Bánfalvi 2011. Pollution by heavy metals is an important environmental problem, and sources that focus on heavy metal pollution often contain information about heavyOXFORD BIBLIOGRAPHIES IN ECOLOGY "HEAVY METAL TOLERANCE" By Nishanta Rajakaruna and Robert S. Boyd

Rajakaruna, Nishanta

118

Thermal Impact of Fasteners in High-Performance Wood-Framed Walls: Preprint  

SciTech Connect (OSTI)

Buildings are heavy consumers of energy, and residential building design is rapidly addressing topics to maximize energy conservation en route to net-zero energy consumption. Annual energy analysis of a building informs the choice among disparate energy measures, for cost, durability, occupant comfort, and whole-house energy use. Physics-based and empirical models of elements of a building are used in such analyses. High-performance wood-framed walls enable builders to construct homes that use much less than 40% of the energy consumed by similar homes built to minimum code. Modeling for these walls has considered physical features such as framing factor, insulation and framing properties, roughness and convective effects, and air leakage. The thermal effects of fasteners used to construct these walls have not been fully evaluated, even though their thermal conductivity is orders of magnitudes higher than that of other building materials. Drywall screws and siding nails are considered in this finite element thermal conductivity analysis of wall sections that represent wood-framed walls that are often used in high-performance homes. Nails and screws reduce even the best walls' insulating performance by approximately 3% and become increasingly significant as the framing factor increases.

Christensen, D.

2011-01-01T23:59:59.000Z

119

Magnetic domain walls driven by interfacial phenomena  

E-Print Network [OSTI]

A domain wall in a ferromagnetic material is a boundary between differently magnetized regions, and its motion provides a convenient scheme to control the magnetization state of the material. Domain walls can be confined ...

Emori, Satoru

2014-01-01T23:59:59.000Z

120

Pressurizer with a mechanically attached surge nozzle thermal sleeve  

DOE Patents [OSTI]

A thermal sleeve is mechanically attached to the bore of a surge nozzle of a pressurizer for the primary circuit of a pressurized water reactor steam generating system. The thermal sleeve is attached with a series of keys and slots which maintain the thermal sleeve centered in the nozzle while permitting thermal growth and restricting flow between the sleeve and the interior wall of the nozzle.

Wepfer, Robert M

2014-03-25T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Wall Drying in Hot and Humid Climates  

E-Print Network [OSTI]

drying potential while at the same time providing a high potential for mold growth. To reduce moisture accumulation in wall systems, it is important to design wall systems that not only reduce moisture intrusion, but also allow drying. Yet often a wall...

Boone, K.; Weston, T.; Pascual, X.

2004-01-01T23:59:59.000Z

122

Method for reducing pressure drop through filters, and filter exhibiting reduced pressure drop  

DOE Patents [OSTI]

Methods for generating and applying coatings to filters with porous material in order to reduce large pressure drop increases as material accumulates in a filter, as well as the filter exhibiting reduced and/or more uniform pressure drop. The filter can be a diesel particulate trap for removing particulate matter such as soot from the exhaust of a diesel engine. Porous material such as ash is loaded on the surface of the substrate or filter walls, such as by coating, depositing, distributing or layering the porous material along the channel walls of the filter in an amount effective for minimizing or preventing depth filtration during use of the filter. Efficient filtration at acceptable flow rates is achieved.

Sappok, Alexander; Wong, Victor

2014-11-18T23:59:59.000Z

123

Managing Inventories of Heavy Actinides  

SciTech Connect (OSTI)

The Department of Energy (DOE) has stored a limited inventory of heavy actinides contained in irradiated targets, some partially processed, at the Savannah River Site (SRS) and Oak Ridge National Laboratory (ORNL). The 'heavy actinides' of interest include plutonium, americium, and curium isotopes; specifically 242Pu and 244Pu, 243Am, and 244/246/248Cm. No alternate supplies of these heavy actinides and no other capabilities for producing them are currently available. Some of these heavy actinide materials are important for use as feedstock for producing heavy isotopes and elements needed for research and commercial application. The rare isotope 244Pu is valuable for research, environmental safeguards, and nuclear forensics. Because the production of these heavy actinides was made possible only by the enormous investment of time and money associated with defense production efforts, the remaining inventories of these rare nuclear materials are an important part of the legacy of the Nuclear Weapons Program. Significant unique heavy actinide inventories reside in irradiated Mark-18A and Mark-42 targets at SRS and ORNL, with no plans to separate and store the isotopes for future use. Although the costs of preserving these heavy actinide materials would be considerable, for all practical purposes they are irreplaceable. The effort required to reproduce these heavy actinides today would likely cost billions of dollars and encompass a series of irradiation and chemical separation cycles for at least 50 years; thus, reproduction is virtually impossible. DOE has a limited window of opportunity to recover and preserve these heavy actinides before they are disposed of as waste. A path forward is presented to recover and manage these irreplaceable National Asset materials for future use in research, nuclear forensics, and other potential applications.

Wham, Robert M [ORNL; Patton, Bradley D [ORNL

2011-01-01T23:59:59.000Z

124

Gas-lubricated seal for sealing between a piston and a cylinder wall  

DOE Patents [OSTI]

A piston-cylinder seal uses gas for a lubricant and has a runner supported on a gapless structure and placed in the space between the piston and the cylinder wall. The runner is deformed elastically under the influence of the operating pressures to follow and compensate for variations in the piston-cylinder fit and maintain a seal. 4 figs.

Hoult, D.P.

1985-09-10T23:59:59.000Z

125

Gas-lubricated seal for sealing between a piston and a cylinder wall  

DOE Patents [OSTI]

A piston-cylinder seal uses gas for a lubricant and has a runner supported on a gapless structure and placed in the space between the piston and the cylinder wall. The runner is deformed elastically under the influence of the operating pressures to follow and compensate for variations in the piston-cylinder fit and maintain a seal.

Hoult, David P. (Box 89, Wellesley, MA 02181)

1985-01-01T23:59:59.000Z

126

Effect of temperature and pressure on the dynamics of nanoconfined propane  

SciTech Connect (OSTI)

We report the effect of temperature and pressure on the dynamical properties of propane confined in nanoporous silica aerogel studied using quasielastic neutron scattering (QENS). Our results demonstrate that the effect of a change in the pressure dominates over the effect of temperature variation on the dynamics of propane nano-confined in silica aerogel. At low pressures, most of the propane molecules are strongly bound to the pore walls, only a small fraction is mobile. As the pressure is increased, the fraction of mobile molecules increases. A change in the mechanism of motion, from continuous diffusion at low pressures to jump diffusion at higher pressures has also been observed.

Gautam, Siddharth, E-mail: gautam.25@osu.edu; Liu, Tingting, E-mail: gautam.25@osu.edu; Welch, Susan; Cole, David [School of Earth Sciences, The Ohio State University, 275 Mendenhall Laboratory, 125 S Oval Mall, Columbus, OH 43210 (United States); Rother, Gernot [Geochemistry and Interfacial Science Group, Chemical Science Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Jalarvo, Niina [Jülich Center for Neutron Sciences (JCNS-1), Forschungszentrum Jülich Outstation at Spallation Neutron Source(SNS), Chemical and Engineering Materials Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Mamontov, Eugene [Spallation Neutron Source (SNS), Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States)

2014-04-24T23:59:59.000Z

127

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

SciTech Connect (OSTI)

The Stanford University Petroleum Research Institute (SUPRI-A) conducts a broad spectrum of research intended to help improve the recovery efficiency from difficult to produce reservoirs including heavy oil and fractured low permeability systems. Our scope of work is relevant across near-, mid-, and long-term time frames. The primary functions of the group are to conduct direction-setting research, transfer research results to industry, and educate and train students for careers in industry. Presently, research in SUPRI-A is divided into 5 main project areas. These projects and their goals include: (1) Multiphase flow and rock properties--to develop better understanding of the physics of displacement in porous media through experiment and theory. This category includes work on imbibition, flow in fractured media, and the effect of temperature on relative permeability and capillary pressure. (2) Hot fluid injection--to improve the application of nonconventional wells for enhanced oil recovery and elucidate the mechanisms of steamdrive in low permeability, fractured porous media. (3) Mechanisms of primary heavy oil recovery--to develop a mechanistic understanding of so-called ''foamy oil'' and its associated physical chemistry. (4) In-situ combustion--to evaluate the effect of different reservoir parameters on the insitu combustion process. (5) Reservoir definition--to develop and improve techniques for evaluating formation properties from production information. What follows is a report on activities for the past year. Significant progress was made in all areas.

Anthony R. Kovscek; Louis M. Castanier

2002-09-30T23:59:59.000Z

128

Factors affecting coking pressures in tall coke ovens  

SciTech Connect (OSTI)

The detrimental effects of excessive coking pressures, resulting in the permanent deformation of coke oven walls, have been recognized for many years. Considerable research has been undertaken worldwide in attempts to define the limits within which a plant may safely operate and to quantify the factors which influence these pressures. Few full scale techniques are available for assessing the potential of a coal blend for causing wall damage. Inference of dangerous swelling pressures may be made however by the measurement of the peak gas pressure which is generated as the plastic layers meet and coalesce at the center of the oven. This pressure is referred to in this report as the carbonizing pressure. At the Dawes Lane cokemaking plant of British Steel`s Scunthorpe Works, a large database has been compiled over several years from the regulator measurement of this pressure. This data has been statistically analyzed to provide a mathematical model for predicting the carbonizing pressure from the properties of the component coals, the results of this analysis are presented in this report.

Grimley, J.J.; Radley, C.E. [British Steel plc, Scunthorpe (United Kingdom). Scunthorpe Works

1995-12-01T23:59:59.000Z

129

Lattice QCD and Hydro/Cascade Model of Heavy Ion Collisions  

E-Print Network [OSTI]

We report here on a recent lattice study of the QCD transition region at finite temperature and zero chemical potential using domain wall fermions (DWF). We also present a parameterization of the QCD equation of state obtained from lattice QCD that is suitable for use in hydrodynamics studies of heavy ion collisions. Finally, we show preliminary results from a multi-stage hydrodynamics/hadron cascade model of a heavy ion collision, in an attempt to understand how well the experimental data (e.g. particle spectra, elliptic flow, and HBT radii) can constrain the inputs (e.g. initial temperature, freezeout temperature, shear viscosity, equation of state) of the theoretical model.

Michael Cheng

2010-05-11T23:59:59.000Z

130

Resistive wall tearing mode generated finite net electromagnetic torque in a static plasma  

SciTech Connect (OSTI)

The MARS-F code [Y. Q. Liu et al., Phys. Plasmas 7, 3681 (2000)] is applied to numerically investigate the effect of the plasma pressure on the tearing mode stability as well as the tearing mode-induced electromagnetic torque, in the presence of a resistive wall. The tearing mode with a complex eigenvalue, resulted from the favorable averaged curvature effect [A. H. Glasser et al., Phys. Fluids 18, 875 (1975)], leads to a re-distribution of the electromagnetic torque with multiple peaking in the immediate vicinity of the resistive layer. The multiple peaking is often caused by the sound wave resonances. In the presence of a resistive wall surrounding the plasma, a rotating tearing mode can generate a finite net electromagnetic torque acting on the static plasma column. Meanwhile, an equal but opposite torque is generated in the resistive wall, thus conserving the total momentum of the whole plasma-wall system. The direction of the net torque on the plasma is always opposite to the real frequency of the mode, agreeing with the analytic result by Pustovitov [Nucl. Fusion 47, 1583 (2007)]. When the wall time is close to the oscillating time of the tearing mode, the finite net torque reaches its maximum. Without wall or with an ideal wall, no net torque on the static plasma is generated by the tearing mode. However, re-distribution of the torque density in the resistive layer still occurs.

Hao, G. Z., E-mail: haogz@swip.ac.cn; Wang, A. K.; Xu, M.; Qu, H. P.; Peng, X. D.; Wang, Z. H.; Xu, J. Q.; Qiu, X. M. [Southwestern Institute of Physics, Post Office Box 432, Chengdu 610041 (China)] [Southwestern Institute of Physics, Post Office Box 432, Chengdu 610041 (China); Liu, Y. Q. [Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom)] [Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom)

2014-01-15T23:59:59.000Z

131

High-pressure microhydraulic actuator  

DOE Patents [OSTI]

Electrokinetic ("EK") pumps convert electric to mechanical work when an electric field exerts a body force on ions in the Debye layer of a fluid in a packed bed, which then viscously drags the fluid. Porous silica and polymer monoliths (2.5-mm O.D., and 6-mm to 10-mm length) having a narrow pore size distribution have been developed that are capable of large pressure gradients (250-500 psi/mm) when large electric fields (1000-1500 V/cm) are applied. Flowrates up to 200 .mu.L/min and delivery pressures up to 1200 psi have been demonstrated. Forces up to 5 lb-force at 0.5 mm/s (12 mW) have been demonstrated with a battery-powered DC-DC converter. Hydraulic power of 17 mW (900 psi@ 180 uL/min) has been demonstrated with wall-powered high voltage supplies. The force and stroke delivered by an actuator utilizing an EK pump are shown to exceed the output of solenoids, stepper motors, and DC motors of similar size, despite the low thermodynamic efficiency.

Mosier, Bruce P. (San Francisco, CA) [San Francisco, CA; Crocker, Robert W. (Fremont, CA) [Fremont, CA; Patel, Kamlesh D. (Dublin, CA) [Dublin, CA

2008-06-10T23:59:59.000Z

132

PressurePressure Indiana Coal Characteristics  

E-Print Network [OSTI]

TimeTime PressurePressure · Indiana Coal Characteristics · Indiana Coals for Coke · Coal Indiana Total Consumption Electricity 59,664 Coke 4,716 Industrial 3,493 Major Coal- red power plantsTransportation in Indiana · Coal Slurry Ponds Evaluation · Site Selection for Coal Gasification · Coal-To-Liquids Study, CTL

Fernández-Juricic, Esteban

133

POROUS WALL, HOLLOW GLASS MICROSPHERES  

SciTech Connect (OSTI)

Hollow Glass Microspheres (HGM) is not a new technology. All one has to do is go to the internet and Google{trademark} HGM. Anyone can buy HGM and they have a wide variety of uses. HGM are usually between 1 to 100 microns in diameter, although their size can range from 100 nanometers to 5 millimeters in diameter. HGM are used as lightweight filler in composite materials such as syntactic foam and lightweight concrete. In 1968 a patent was issued to W. Beck of the 3M{trademark} Company for 'Glass Bubbles Prepared by Reheating Solid Glass Particles'. In 1983 P. Howell was issued a patent for 'Glass Bubbles of Increased Collapse Strength' and in 1988 H. Marshall was issued a patent for 'Glass Microbubbles'. Now Google{trademark}, Porous Wall, Hollow Glass Microspheres (PW-HGMs), the key words here are Porous Wall. Almost every article has its beginning with the research done at the Savannah River National Laboratory (SRNL). The Savannah River Site (SRS) where SRNL is located has a long and successful history of working with hydrogen and its isotopes for national security, energy, waste management and environmental remediation applications. This includes more than 30 years of experience developing, processing, and implementing special ceramics, including glasses for a variety of Department of Energy (DOE) missions. In the case of glasses, SRS and SRNL have been involved in both the science and engineering of vitreous or glass based systems. As a part of this glass experience and expertise, SRNL has developed a number of niches in the glass arena, one of which is the development of porous glass systems for a variety of applications. These porous glass systems include sol gel glasses, which include both xerogels and aerogels, as well as phase separated glass compositions, that can be subsequently treated to produce another unique type of porosity within the glass forms. The porous glasses can increase the surface area compared to 'normal glasses of a 1 to 2 order of magnitude, which can result in unique properties in areas such as hydrogen storage, gas transport, gas separations and purifications, sensors, global warming applications, new drug delivery systems and so on. One of the most interesting porous glass products that SRNL has developed and patented is Porous Wall, Hollow Glass Microspheres (PW-HGMs) that are being studied for many different applications. The European Patent Office (EPO) just recently notified SRS that the continuation-in-part patent application for the PW-HGMs has been accepted. The original patent, which was granted by the EPO on June 2, 2010, was validated in France, Germany and the United Kingdom. The microspheres produced are generally in the range of 2 to 100 microns, with a 1 to 2 micron wall. What makes the SRNL microspheres unique from all others is that the team in Figure 1 has found a way to induce and control porosity through the thin walls on a scale of 100 to 3000 {angstrom}. This is what makes the SRNL HW-HGMs one-of-a-kind, and is responsible for many of their unique properties and potential for various applications, including those in tritium storage, gas separations, H-storage for vehicles, and even a variety of new medical applications in the areas of drug delivery and MRI contrast agents. SRNL Hollow Glass Microspheres, and subsequent, Porous Wall, Hollow Glass Microspheres are fabricated using a flame former apparatus. Figure 2 is a schematic of the apparatus.

Sexton, W.

2012-06-30T23:59:59.000Z

134

SOVENT BASED ENHANCED OIL RECOVERY FOR IN-SITU UPGRADING OF HEAVY OIL SANDS  

SciTech Connect (OSTI)

With the depletion of conventional crude oil reserves in the world, heavy oil and bitumen resources have great potential to meet the future demand for petroleum products. However, oil recovery from heavy oil and bitumen reservoirs is much more difficult than that from conventional oil reservoirs. This is mainly because heavy oil or bitumen is partially or completely immobile under reservoir conditions due to its extremely high viscosity, which creates special production challenges. In order to overcome these challenges significant efforts were devoted by Applied Research Center (ARC) at Florida International University and The Center for Energy Economics (CEE) at the University of Texas. A simplified model was developed to assess the density of the upgraded crude depending on the ratio of solvent mass to crude oil mass, temperature, pressure and the properties of the crude oil. The simplified model incorporated the interaction dynamics into a homogeneous, porous heavy oil reservoir to simulate the dispersion and concentration of injected CO2. The model also incorporated the characteristic of a highly varying CO2 density near the critical point. Since the major challenge in heavy oil recovery is its high viscosity, most researchers have focused their investigations on this parameter in the laboratory as well as in the field resulting in disparaging results. This was attributed to oil being a complex poly-disperse blend of light and heavy paraffins, aromatics, resins and asphaltenes, which have diverse behaviors at reservoir temperature and pressures. The situation is exacerbated by a dearth of experimental data on gas diffusion coefficients in heavy oils due to the tedious nature of diffusivity measurements. Ultimately, the viscosity and thus oil recovery is regulated by pressure and its effect on the diffusion coefficient and oil swelling factors. The generation of a new phase within the crude and the differences in mobility between the new crude matrix and the precipitate readily enables removal of asphaltenes. Thus, an upgraded crude low in heavy metal, sulfur and nitrogen is more conducive for further purification.

Munroe, Norman

2009-01-30T23:59:59.000Z

135

HEAVY WATER COMPONENTS TEST REACTOR DECOMMISSIONING  

SciTech Connect (OSTI)

The Heavy Water Components Test Reactor (HWCTR) Decommissioning Project was initiated in 2009 as a Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) Removal Action with funding from the American Recovery and Reinvestment Act (ARRA). This paper summarizes the history prior to 2009, the major D&D activities, and final end state of the facility at completion of decommissioning in June 2011. The HWCTR facility was built in 1961, operated from 1962 to 1964, and is located in the northwest quadrant of the Savannah River Site (SRS) approximately three miles from the site boundary. The HWCTR was a pressurized heavy water test reactor used to develop candidate fuel designs for heavy water power reactors. In December of 1964, operations were terminated and the facility was placed in a standby condition as a result of the decision by the U.S. Atomic Energy Commission to redirect research and development work on heavy water power reactors to reactors cooled with organic materials. For about one year, site personnel maintained the facility in a standby status, and then retired the reactor in place. In the early 1990s, DOE began planning to decommission HWCTR. Yet, in the face of new budget constraints, DOE deferred dismantlement and placed HWCTR in an extended surveillance and maintenance mode. The doors of the reactor facility were welded shut to protect workers and discourage intruders. In 2009 the $1.6 billion allocation from the ARRA to SRS for site footprint reduction at SRS reopened the doors to HWCTR - this time for final decommissioning. Alternative studies concluded that the most environmentally safe, cost effective option for final decommissioning was to remove the reactor vessel, both steam generators, and all equipment above grade including the dome. The transfer coffin, originally above grade, was to be placed in the cavity vacated by the reactor vessel and the remaining below grade spaces would be grouted. Once all above equipment including the dome was removed, a concrete cover was to be placed over the remaining footprint and the groundwater monitored for an indefinite period to ensure compliance with environmental regulations.

Austin, W.; Brinkley, D.

2011-10-13T23:59:59.000Z

136

RESIDUAL STRESS DISTRIBUTIONS FOR MULTI-PASS WELDS IN PRESSURE VESSEL AND PIPING COMPONENTS  

E-Print Network [OSTI]

RESIDUAL STRESS DISTRIBUTIONS FOR MULTI-PASS WELDS IN PRESSURE VESSEL AND PIPING COMPONENTS distributions in common pressure vessel and piping components is generated by using the multi-pass finite-walled pipes with various radius to thickness ratios. Both single- and double-V weld joints are investigated

Michaleris, Panagiotis

137

Analysis of Rotating Collectors from the Private Region of JET with Carbon Wall and Metallic ITER-Like Wall  

E-Print Network [OSTI]

Analysis of Rotating Collectors from the Private Region of JET with Carbon Wall and Metallic ITER-Like Wall

138

LCLS Heavy Met Outgassing Tests  

SciTech Connect (OSTI)

A Heavy Met that is 95% tungsten, 3% nickel and 2% iron and sintered to 100% density and is Ultra High Vacuum (UHV) compatible is proposed for use as the X-ray slit in the Front End Enclosure and the Fixed Mask for the Linac Coherent Light Source (LCLS). The Heavy Met was tested in the LLNL Vacuum Sciences and Engineering Lab (VSEL) to determine its outgassing rate and its overall compatibility with the vacuum requirements for LCLS.

Kishiyama, K. I.

2010-12-01T23:59:59.000Z

139

SRNL POROUS WALL GLASS MICROSPHERES  

SciTech Connect (OSTI)

The Savannah River National Laboratory (SRNL) has developed a new medium for storage of hydrogen and other gases. This involves fabrication of thin, Porous Walled, Hollow Glass Microspheres (PW-HGMs), with diameters generally in the range of 1 to several hundred microns. What is unique about the glass microballons is that porosity has been induced and controlled within the thin, one micron thick walls, on the scale of 10 to several thousand Angstroms. This porosity results in interesting properties including the ability to use these channels to fill the microballons with special absorbents and other materials, thus providing a contained environment even for reactive species. Gases can now enter the microspheres and be retained on the absorbents, resulting in solid-state and contained storage of even reactive species. Also, the porosity can be altered and controlled in various ways, and even used to filter mixed gas streams within a system. SRNL is involved in about a half dozen different programs involving these PW-HGMs and an overview of some of these activities and results emerging are presented.

Wicks, G; Leung Heung, L; Ray Schumacher, R

2008-04-15T23:59:59.000Z

140

Wall current probe: A non-invasive in situ plasma diagnostic for space and time resolved current density distribution measurement  

SciTech Connect (OSTI)

In the context of low temperature plasma research, we propose a wall current probe to determine the local charged particle fluxes flowing to the chamber walls. This non-intrusive planar probe consists of an array of electrode elements which can be individually biased and for which the current can be measured separately. We detail the probe properties and present the ability of the diagnostic to be used as a space and time resolved measurement of the ion and electron current density at the chamber walls. This diagnostic will be relevant to study the electron transport in magnetized low-pressure plasmas.

Baude, R.; Gaboriau, F.; Hagelaar, G. J. M. [Université de Toulouse, UPS, INPT, LAPLACE (Laboratoire Plasma et Conversion d’énergie), 118 route de Narbonne, F-31062 Toulouse Cedex 9, France and CNRS, LAPLACE, F-31062, Toulouse (France)] [Université de Toulouse, UPS, INPT, LAPLACE (Laboratoire Plasma et Conversion d’énergie), 118 route de Narbonne, F-31062 Toulouse Cedex 9, France and CNRS, LAPLACE, F-31062, Toulouse (France)

2013-08-15T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Design and fabrication of a MEMS-array pressure sensor system for passive underwater navigation inspired by the lateral line  

E-Print Network [OSTI]

An object within a fluid flow generates local pressure variations that are unique and characteristic to the object's shape and size. For example, a three-dimensional object or a wall-like obstacle obstructs flow and creates ...

Hou, Stephen Ming-Chang, 1981-

2012-01-01T23:59:59.000Z

142

Performance limits of fusion first-wall structural materials.  

SciTech Connect (OSTI)

Key features of fusion energy relate primarily to potential advantages associated with safety and environmental considerations and the near endless supply of fuel. However, it is generally concluded that high performance fusion power systems will be required in order to be economically competitive with other energy options. As in most energy systems, structural materials operating limits pose a primary constraint to the performance of fusion power systems. It is also recognized that for the case of fusion power, the first-wall/blanket system will have a dominant impact on both the economic and safety/environmental attractiveness of fusion energy. The first-wall blanket structure is particularly critical since it must maintain high integrity at relatively high temperatures during exposure to high radiation levels, high surface heat fluxes, and significant primary stresses. The performance limits of the first-wall/blanket structure will be dependent on the structural material properties, the coolant/breeder system, and the specific design configuration. Key factors associated with high performance structural materials include (1) high temperature operation, (2) a large operating temperature window, and (3) a long operating lifetime. High temperature operation is necessary to provide for high power conversion efficiency. As discussed later, low-pressure coolant systems provide significant advantages. A large operating temperature window is necessary to accommodate high surface heating and high power density. The operating temperature range for the structure must include the temperature gradient through the first wall and the coolant system AT required for efficient energy conversion. This later requirement is dependent on the coolant/breeder operating temperature limits. A long operating lifetime of the structure is important to improve system availability and to minimize waste disposition.

Smith, D. L.; Majumdar, S.; Billone, M.; Mattas, R. F.

1999-11-12T23:59:59.000Z

143

A Helical Coolant Channel Design for the Solid Wall Blanket  

SciTech Connect (OSTI)

A helical coolant channel scheme is proposed for the APEX solid wall blanket module. The self-coolant breeder in this system is FLIBE (LiF)2(BeF2). The structural material is the nanocomposited alloy 12YWT. The neutron multiplier used in the current design is either stationary or slow moving liquid lead. The purpose of this study is to design a blanket that can handle a high wall loading (5 MW/m{sup 2}). In the mean time the design provides means to attain the maximum possible blanket outlet temperature and meet all engineering limits on temperature of structural material and liquids. An important issue for such a design is to optimize the system for minimum pressure loss. For advanced ferritic steel (12YWT) an upper temperature limit of 800 deg. C is expected, and a limit of 700 deg. C at the steel/FLIBE interface is recommended.The blanket module is composed of two main continuous routes. The first route is three helical rectangular channels side-by-side that surround a central box. The helical channels are fed from the bottom and exit at the top to feed the central channels in the central box. The coolant helical channels have a cross sectional area with a length of about 10 cm and a width that changes according to the position around the central box. For instance: the width of the coolant channels facing the plasma is the narrowest while it is the widest in the back (farthest from the plasma).In this design the coolant runs around the central box for only 5 turns to cover the total height of the first wall (6.8 m). The design is optimized with the FW channel width as a parameter with the heat transfer requirements at the first wall as the constraints.

Mogahed, E.A. [University of Wisconsin-Madison (United States)

2003-07-15T23:59:59.000Z

144

Textural break foundation wall construction modules  

DOE Patents [OSTI]

Below-grade, textural-break foundation wall structures are provided for inhibiting diffusion and advection of liquids and gases into and out from a surrounding hydrogeologic environment. The foundation wall structure includes a foundation wall having an interior and exterior surface and a porous medium disposed around a portion of the exterior surface. The structure further includes a modular barrier disposed around a portion of the porous medium. The modular barrier is substantially removable from the hydrogeologic environment.

Phillips, Steven J. (Kennewick, WA)

1990-01-01T23:59:59.000Z

145

Panelized wall system with foam core insulation  

DOE Patents [OSTI]

A wall system includes a plurality of wall members, the wall members having a first metal panel, a second metal panel, and an insulating core between the first panel and the second panel. At least one of the first panel and the second panel include ridge portions. The insulating core can be a foam, such as a polyurethane foam. The foam can include at least one opacifier to improve the k-factor of the foam.

Kosny, Jan (Oak Ridge, TN); Gaskin, Sally (Houston, TX)

2009-10-20T23:59:59.000Z

146

First wall for polarized fusion reactors  

DOE Patents [OSTI]

Depolarization mechanisms arising from the recycling of the polarized fuel at the limiter and the first-wall of a fusion reactor are greater than those mechanisms in the plasma. Rapid depolarization of the plasma is prevented by providing a first-wall or first-wall coating formed of a low-Z, non-metallic material having a depolarization rate greater than 1 sec.sup.-1.

Greenside, Henry S. (Cranbury, NJ); Budny, Robert V. (Princeton, NJ); Post, Jr., Douglass E. (Buttonwood, CT)

1988-01-01T23:59:59.000Z

147

Direct Measurements of the Lifetime of Heavy Hypernuclei  

E-Print Network [OSTI]

The lifetime of a Lambda particle embedded in a nucleus (hypernucleus) decreases from that of free Lambda decay due to the opening of the Lambda N to NN weak decay channel. However, it is generally believed that the lifetime of a hypernucleus attains a constant value (saturation) for medium to heavy hypernuclear masses, yet this hypothesis has been difficult to verify. The present paper reports a direct measurement of the lifetime of medium-heavy hypernuclei produced with a photon-beam from Fe, Cu, Ag, and Bi targets. The recoiling hypernuclei were detected by a fission fragment detector using low-pressure multi-wire proportional chambers. The experiment agrees remarkably well with the only previously-measured single-species heavy-hypernucleus lifetime, that of Fe56_Lambda at KEK, and has significantly higher precision. The experiment disagrees with the measured lifetime of an unknown combination of heavy hypernuclei with 180

X. Qiu; L. Tang; A. Margaryan; P. Achenbach; A. Ahmidouch; I. Albayrak; D. Androic; A. Asaturyan; R. Asaturyan; O. Ates; R. Badui; P. Baturin; W. Boeglin; J. Bono; E. Brash; P. Carter; C. Chen; X. Chen; A. Chiba; E. Christy; M. M. Dalton; S. Danagoulian; R. De Leo; D. Doi; M. Elaasar; R. Ent; H. Fenker; Y. Fujii; M. Furic; M. Gabrielyan; L. Gan; F. Garibaldi; D. Gaskell; A. Gasparian; T. Gogami; O. Hashimoto; T. Horn; B. Hu; E. V. Hungerford; M. Jones; H. Kanda; M. Kaneta; M. Kawai; D. Kawama; H. Khanal; M. Kohl; A. Liyanage; W. Luo; K. Maeda; P. Markowitz; T. Maruta; A. Matsumura; V. Maxwell; A. Mkrtchyan; H. Mkrtchyan; S. Nagao; S. N. Nakamura; A. Narayan; C. Neville; G. Niculescu; M. I. Niculescu; A. Nunez; Nuruzzaman; Y. Okayasu; T. Petkovic; J. Pochodzalla; J. Reinhold; V. M. Rodriguez; C. Samanta; B. Sawatzky; T. Seva; A. Shichijo; V. Tadevosyan; N. Taniya; K. Tsukada; M. Veilleux; W. Vulcan; F. R. Wesselmann; S. A. Wood; L. Ya; T. Yamamoto; Z. Ye; K. Yokota; L. Yuan; S. Zhamkochyan; L. Zhu

2013-01-16T23:59:59.000Z

148

Liquid Walls Innovative High Power Density Concepts  

E-Print Network [OSTI]

-CLIFF 3.High-Temperature Refractory Solid Wall -EVOLVE (Two-Phase Lithium Flow) -Helium Cooling erosion as limiting factors -Results in smaller and lower cost components (chamb

California at Los Angeles, University of

149

First wall for polarized fusion reactors  

DOE Patents [OSTI]

A first-wall or first-wall coating for use in a fusion reactor having polarized fuel may be formed of a low-Z non-metallic material having slow spin relaxation, i.e., a depolarization rate greater than 1 sec/sup -1/. Materials having these properties include hydrogenated and deuterated amorphous semiconductors. A method for preventing the rapid depolarization of a polarized plasma in a fusion device may comprise the step of providing a first-wall or first-wall coating formed of a low-Z, non-metallic material having a depolarization rate greater than 1 sec/sup -1/.

Greenside, H.S.; Budny, R.V.; Post, D.E. Jr.

1985-01-29T23:59:59.000Z

150

Multiple moving wall dry coal extrusion pump  

DOE Patents [OSTI]

A pump for transporting particulate material includes a passageway defined on each side between an inlet and an outlet by a moving wall.

Fitzsimmons, Mark Andrew

2013-05-14T23:59:59.000Z

151

Ultrasonic Digital Communication System for a Steel Wall Multipath Channel: Methods and Results  

SciTech Connect (OSTI)

As of the development of this thesis, no commercially available products have been identified for the digital communication of instrumented data across a thick ({approx} 6 n.) steel wall using ultrasound. The specific goal of the current research is to investigate the application of methods for digital communication of instrumented data (i.e., temperature, voltage, etc.) across the wall of a steel pressure vessel. The acoustic transmission of data using ultrasonic transducers prevents the need to breach the wall of such a pressure vessel which could ultimately affect its safety or lifespan, or void the homogeneity of an experiment under test. Actual digital communication paradigms are introduced and implemented for the successful dissemination of data across such a wall utilizing solely an acoustic ultrasonic link. The first, dubbed the ''single-hop'' configuration, can communicate bursts of digital data one-way across the wall using the Differential Binary Phase-Shift Keying (DBPSK) modulation technique as fast as 500 bps. The second, dubbed the ''double-hop'' configuration, transmits a carrier into the vessel, modulates it, and retransmits it externally. Using a pulsed carrier with Pulse Amplitude Modulation (PAM), this technique can communicate digital data as fast as 500 bps. Using a CW carrier, Least Mean-Squared (LMS) adaptive interference suppression, and DBPSK, this method can communicate data as fast as 5 kbps. A third technique, dubbed the ''reflected-power'' configuration, communicates digital data by modulating a pulsed carrier by varying the acoustic impedance at the internal transducer-wall interface. The paradigms of the latter two configurations are believed to be unique. All modulation methods are based on the premise that the wall cannot be breached in any way and can therefore be viably implemented with power delivered wirelessly through the acoustic channel using ultrasound. Methods, results, and considerations for future research are discussed herein.

TL Murphy

2006-02-16T23:59:59.000Z

152

Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

ce001musculus2011o.pdf More Documents & Publications Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty Combustion Modeling Heavy-Duty Low-Temperature and Diesel...

153

Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

ce001musculus2010o.pdf More Documents & Publications Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty Combustion Modeling Heavy-Duty Low-Temperature and Diesel...

154

Virtual gap dielectric wall accelerator  

DOE Patents [OSTI]

A virtual, moving accelerating gap is formed along an insulating tube in a dielectric wall accelerator (DWA) by locally controlling the conductivity of the tube. Localized voltage concentration is thus achieved by sequential activation of a variable resistive tube or stalk down the axis of an inductive voltage adder, producing a "virtual" traveling wave along the tube. The tube conductivity can be controlled at a desired location, which can be moved at a desired rate, by light illumination, or by photoconductive switches, or by other means. As a result, an impressed voltage along the tube appears predominantly over a local region, the virtual gap. By making the length of the tube large in comparison to the virtual gap length, the effective gain of the accelerator can be made very large.

Caporaso, George James; Chen, Yu-Jiuan; Nelson, Scott; Sullivan, Jim; Hawkins, Steven A

2013-11-05T23:59:59.000Z

155

Beetle Kill Wall at NREL  

ScienceCinema (OSTI)

When it comes to designing an interior decorative feature for one of the most energy efficient office buildings in the world, very few would consider bringing in a beetle to do the job. But thats what happened at the U.S. Department of Energy's (DOE) Research Support Facility (RSF) located on the National Renewable Energy Laboratory (NREL) campus.In June, the RSF will become home to more than 800 workers from DOE and NREL and building visitors will be greeted with a soaring, two-story high wall entirely covered with wood harvested from the bark beetle infestation that has killed millions of pine trees in the Western U.S. But, the use of beetle kill wood is just one example of the resources being leveraged to make the RSF a model for sustainability and one more step toward NRELs goal to be a net zero energy campus.

None

2013-05-29T23:59:59.000Z

156

Pressure reducing regulator  

DOE Patents [OSTI]

A pressure reducing regulator that controls its downstream or outlet pressure to a fixed fraction of its upstream or inlet pressure. The regulator includes a housing which may be of a titanium alloy, within which is located a seal or gasket at the outlet end which may be made of annealed copper, a rod, and piston, each of which may be made of high density graphite. The regulator is insensitive to temperature by virtue of being without a spring or gas sealed behind a diaphragm, and provides a reference for a system in which it is being used. The rod and piston of the regulator are constructed, for example, to have a 1/20 ratio such that when the downstream pressure is less than 1/20 of the upstream pressure the regulator opens and when the downstream pressure exceeds 1/20 of the upstream pressure the regulator closes.

Whitehead, John C. (Davis, CA); Dilgard, Lemoyne W. (Willits, CA)

1995-01-01T23:59:59.000Z

157

Grazing collisions of gravitational shock waves and entropy production in heavy ion collisions  

SciTech Connect (OSTI)

AdS/CFT correspondence is now widely used for the study of strongly coupled plasmas, such as those produced in ultrarelativistic heavy ion collisions at the Relativistic Heavy Ion Collider. While properties of equilibrated plasma and small deviations from equilibrium are by now reasonably well understood, the plasma's initial formation and thermal equilibration is a much more challenging issue which remains to be studied. In the dual gravity language, these problems are related to the formation of bulk black holes, and studying trapped surfaces, as we do in this work, is a way to estimate the properties (temperature and entropy) of such black holes. Extending the work by Gubser et al. for central collisions, we find numerically trapped surfaces for noncentral collisions of ultrarelativistic black holes (gravitational shock waves) with different energies. We observe that beyond a certain critical impact parameter, the trapped surface does not exist, and we argue that there are some experimental indications for a similar jump in entropy production as a function of the impact parameter in real heavy ion collisions. We also present a simple solvable example of the so-called wall-on-wall collision, for colliding objects that depend on the holographic coordinate only. Finally, we critically discuss the applicability of the AdS/CFT approach to real-world heavy ion collisions.

Lin Shu; Shuryak, Edward [Department of Physics and Astronomy, SUNY, Stony Brook, New York 11794 (United States)

2009-06-15T23:59:59.000Z

158

Five Years of Tracking Heavy Ion Collisions at RHIC  

E-Print Network [OSTI]

Five years have passed since the first collisions of Au nuclei at the Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Laboratory (BNL) on Long Island. With nucleon-nucleon center-of-mass energies of up to sqrt(s_NN)=200GeV RHIC provides the highest energy heavy ion collisions at any existing collider. To study the dynamics of nuclear matter at extreme temperatures and pressures hundreds of produced particles need to be tracked and identified, which provides a sizable challenge to the four experiments. This article tries to summarize these first years of RHIC operation from the detector point of view and give a glimpse at the future of the accelerator and its experiments.

A. Franz

2006-03-13T23:59:59.000Z

159

Density hysteresis of heavy water confined in a nanoporous silica matrix  

E-Print Network [OSTI]

A neutron scattering technique was developed to measure the density of heavy water confined in a nanoporous silica matrix in a temperature-pressure range, from 300 to 130 K and from 1 to 2,900 bars, where bulk water will ...

Faraone, Antonio

160

Evolution of seismic velocities in heavy oil sand reservoirs during thermal recovery process  

E-Print Network [OSTI]

1 Evolution of seismic velocities in heavy oil sand reservoirs during thermal recovery process. Larribau 64018 Pau Cedex, France Oil and Gas Science and Technology 2012, 67 (6), 1029-1039, doi:10 pressure and temperature in the rock reservoir, that are most often unconsolidated or weakly consolidated

Paris-Sud XI, Université de

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Chemistry of heavy ion reactions  

SciTech Connect (OSTI)

The use of heavy ions to induce nuclear reactions was reported as early as 1950. Since that time it has been one of the most active areas of nuclear research. Intense beams of ions as heavy as uranium with energies high enough to overcome the Coulomb barriers of even the heaviest elements are available. The wide variety of possible reactions gives rise to a multitude of products which have been studied by many ingenious chemical and physical techniques. Chemical techniques have been of special value for the separation and unequivocal identification of low yield species from the plethora of other nuclides present. Heavy ion reactions have been essential for the production of the trans-Md elements and a host of new isotopes. The systematics of compound nucleus reactions, transfer reactions, and deeply inelastic reactions have been elucidated using chemical techniques. A review of the variety of chemical procedures and techniques which have been developed for the study of heavy ion reactions and their products is given. Determination of the chemical properties of the trans-Md elements, which are very short-lived and can only be produced an ''atom-at-a-time'' via heavy ion reactions, is discussed. 53 refs., 19 figs.

Hoffman, D.C.

1988-10-01T23:59:59.000Z

162

A Better Method for Evaluating Heavy Metal Water Pollution  

E-Print Network [OSTI]

efforts to control heavy metal pollution have focused oncomponent of heavy metal pollution, Dr. Hering found thatthat makes measuring heavy metal pollution a moving target.

Hering, Janet

2002-01-01T23:59:59.000Z

163

Remarks on Liquid Wall Research Mohamed Abdou  

E-Print Network [OSTI]

Remarks on Liquid Wall Research Mohamed Abdou Professor Mechanical and Aerospace Engineering UCLA physicists and engineering scientists · Enhances synergism between IFE and MFE · Provides excellent disciplines. #12;Several "Ideas" Have Been Proposed for Liquid Walls Fluids 1) High-conductivity, low Pr

California at Los Angeles, University of

164

External Insulation of Masonry Walls and Wood Framed Walls  

SciTech Connect (OSTI)

The use of exterior insulation on a building is an accepted and effective means to increase the overall thermal resistance of the assembly that also has other advantages of improved water management and often increased air tightness of building assemblies. For thin layers of insulation (1" to 1 1/2"), the cladding can typically be attached directly through the insulation back to the structure. For thicker insulation layers, furring strips have been added as a cladding attachment location. This approach has been used in the past on numerous Building America test homes and communities (both new and retrofit applications), and has been proven to be an effective and durable means to provide cladding attachment. However, the lack of engineering data has been a problem for many designers, contractors, and code officials. This research project developed baseline engineering analysis to support the installation of thick layers of exterior insulation on existing masonry and frame walls. Furthermore, water management details necessary to integrate windows, doors, decks, balconies and roofs were created to provide guidance on the integration of exterior insulation strategies with other enclosure elements.

Baker, P.

2013-01-01T23:59:59.000Z

165

2003 Plant Cell Walls Gordon Conference  

SciTech Connect (OSTI)

This conference will address recent progress in many aspects of cell wall biology. Molecular, genetic, and genomic approaches are yielding major advances in our understanding of the composition, synthesis, and architecture of plant cell walls and their dynamics during growth, and are identifying the genes that encode the machinery needed to make their biogenesis possible. This meeting will bring together international scientists from academia, industry and government labs to share the latest breakthroughs and perspectives on polysaccharide biosynthesis, wood formation, wall modification, expansion and interaction with other organisms, and genomic & evolutionary analyses of wall-related genes, as well as to discuss recent ''nanotechnological'' advances that take wall analysis to the level of a single cell.

Daniel J. Cosgrove

2004-09-21T23:59:59.000Z

166

Perfusion of veins at arterial pressure increases the expression of KLF5 and cell cycle genes in smooth muscle cells  

SciTech Connect (OSTI)

Vascular smooth muscle cell (VSMC) proliferation remains a major cause of veno-arterial graft failure. We hypothesised that exposure of venous SMCs to arterial pressure would increase KLF5 expression and that of cell cycle genes. Porcine jugular veins were perfused at arterial or venous pressure in the absence of growth factors. The KLF5, c-myc, cyclin-D and cyclin-E expression were elevated within 24 h of perfusion at arterial pressure but not at venous pressure. Arterial pressure also reduced the decline in SM-myosin heavy chain expression. These data suggest a role for KLF5 in initiating venous SMCs proliferation in response to arterial pressure.

Amirak, Emre [Section of Molecular Medicine, National Heart and Lung Institute, Imperial College London, Sir Alexander Fleming Building, South Kensington Campus, London SW7 2AZ (United Kingdom)] [Section of Molecular Medicine, National Heart and Lung Institute, Imperial College London, Sir Alexander Fleming Building, South Kensington Campus, London SW7 2AZ (United Kingdom); Zakkar, Mustafa; Evans, Paul C. [Cardiovascular Sciences, Bywaters Center for Vascular Inflammation, National Heart and Lung Institute, Imperial College London, Hammersmith Hospital, London W12 ONN (United Kingdom)] [Cardiovascular Sciences, Bywaters Center for Vascular Inflammation, National Heart and Lung Institute, Imperial College London, Hammersmith Hospital, London W12 ONN (United Kingdom); Kemp, Paul R., E-mail: p.kemp@imperial.ac.uk [Section of Molecular Medicine, National Heart and Lung Institute, Imperial College London, Sir Alexander Fleming Building, South Kensington Campus, London SW7 2AZ (United Kingdom)

2010-01-01T23:59:59.000Z

167

Final Report for "Stabilization of resistive wall modes using moving metal walls"  

SciTech Connect (OSTI)

The UW experiment used a linear pinch experiment to study the stabilization of MHD by moving metal walls. The methodology of the experiment had three steps. (1) Identify and understand the no-wall MHD instability limits and character, (2) identify and understand the thin-wall MHD instabilities (re- sistive wall mode), and then (3) add the spinning wall and understand its impact on stability properties. During the duration of the grant we accomplished all 3 of these goals, discovered new physics, and completed the experiment as proposed.

Forest, Cary B.

2014-02-05T23:59:59.000Z

168

Pionic Fusion of Heavy Ions  

E-Print Network [OSTI]

We report the first experimental observation of the pionic fusion of two heavy ions. The 12C(12C,24Mg)pi0 and 12C(12C,24Na)pi+ cross sections have been measured to be 208 +/- 38 and 182 +/- 84 picobarns, respectively, at E_cm = 137 MeV. This cross section for heavy-ion pion production, at an energy just 6 MeV above the absolute energy-conservation limit, constrains possible production mechanisms to incorporate the kinetic energy of the entire projectile-target system as well as the binding energy gained in fusion.

D. Horn; G. C. Ball; D. R. Bowman; W. G. Davies; D. Fox; A. Galindo-Uribarri; A. C. Hayes; G. Savard; L. Beaulieu; Y. Larochelle; C. St-Pierre

1996-08-13T23:59:59.000Z

169

Central collisions of heavy ions  

SciTech Connect (OSTI)

This report describes the activities of the Heavy Ion Physics Group at the University of California, Riverside from October 1, 1990 to September 30, 1991. During this period, our program focuses on particle production at AGS energies, and correlation studies at the Bevalac in nucleus central collisions. We participated in the preparation of letters of intent for two RHIC experiments -- the OASIS proposal and the Di-Muon proposal -- and worked on two RHIC R D efforts -- a silicon strip detector project and a muon-identifier project. A small fraction of time was also devoted to physics programs outside the realm of heavy ion reactions by several individuals.

Fung, Sun-yiu.

1991-10-01T23:59:59.000Z

170

Heavy Ions - 88-Inch Cyclotron  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation Desert Southwest Region service area. TheEPSCIResearchGulfCenterHeavy Ions Heavy ions

171

Control of linear modes in cylindrical resistive magnetohydrodynamics with a resistive wall, plasma rotation, and complex gain  

SciTech Connect (OSTI)

Feedback stabilization of magnetohydrodynamic (MHD) modes in a tokamak is studied in a cylindrical model with a resistive wall, plasma resistivity, viscosity, and toroidal rotation. The control is based on a linear combination of the normal and tangential components of the magnetic field just inside the resistive wall. The feedback includes complex gain, for both the normal and for the tangential components, and it is known that the imaginary part of the feedback for the former is equivalent to plasma rotation [J. M. Finn and L. Chacon, Phys. Plasmas 11, 1866 (2004)]. The work includes (1) analysis with a reduced resistive MHD model for a tokamak with finite ? and with stepfunction current density and pressure profiles, and (2) computations with a full compressible visco-resistive MHD model with smooth decreasing profiles of current density and pressure. The equilibria are stable for ??=?0 and the marginal stability values ?{sub rp,rw}?wall; resistive plasma, ideal wall; ideal plasma, resistive wall; and ideal plasma, ideal wall) are computed for both models. The main results are: (a) imaginary gain with normal sensors or plasma rotation stabilizes below ?{sub rp,iw} because rotation suppresses the diffusion of flux from the plasma out through the wall and, more surprisingly, (b) rotation or imaginary gain with normal sensors destabilizes above ?{sub rp,iw} because it prevents the feedback flux from entering the plasma through the resistive wall to form a virtual wall. A method of using complex gain G{sub i} to optimize in the presence of rotation in this regime with ??>??{sub rp,iw} is presented. The effect of imaginary gain with tangential sensors is more complicated but essentially destabilizes above and below ?{sub rp,iw}.

Brennan, D. P. [Department of Astrophysical Sciences, Princeton University, Princeton, New Jersey 08544 (United States); Finn, J. M. [Applied Mathematics and Plasma Physics, Theoretical Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

2014-10-15T23:59:59.000Z

172

High temperature pressure gauge  

DOE Patents [OSTI]

A high temperature pressure gauge comprising a pressure gauge positioned in fluid communication with one end of a conduit which has a diaphragm mounted in its other end. The conduit is filled with a low melting metal alloy above the diaphragm for a portion of its length with a high temperature fluid being positioned in the remaining length of the conduit and in the pressure gauge.

Echtler, J. Paul (Pittsburgh, PA); Scandrol, Roy O. (Library, PA)

1981-01-01T23:59:59.000Z

173

Pressurized fluidized bed reactor  

DOE Patents [OSTI]

A pressurized fluid bed reactor power plant includes a fluidized bed reactor contained within a pressure vessel with a pressurized gas volume between the reactor and the vessel. A first conduit supplies primary gas from the gas volume to the reactor, passing outside the pressure vessel and then returning through the pressure vessel to the reactor, and pressurized gas is supplied from a compressor through a second conduit to the gas volume. A third conduit, comprising a hot gas discharge, carries gases from the reactor, through a filter, and ultimately to a turbine. During normal operation of the plant, pressurized gas is withdrawn from the gas volume through the first conduit and introduced into the reactor at a substantially continuously controlled rate as the primary gas to the reactor. In response to an operational disturbance of the plant, the flow of gas in the first, second, and third conduits is terminated, and thereafter the pressure in the gas volume and in the reactor is substantially simultaneously reduced by opening pressure relief valves in the first and third conduits, and optionally by passing air directly from the second conduit to the turbine. 1 fig.

Isaksson, J.

1996-03-19T23:59:59.000Z

174

NETL SOFC: Pressurized Systems  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

(HHV) with greater than 97 percent carbon capture, near-zero emissions, and low water usage. The Pressurized Systems key technology is developing a deeper understanding on the...

175

Pressurized fluidized bed reactor  

DOE Patents [OSTI]

A pressurized fluid bed reactor power plant includes a fluidized bed reactor contained within a pressure vessel with a pressurized gas volume between the reactor and the vessel. A first conduit supplies primary gas from the gas volume to the reactor, passing outside the pressure vessel and then returning through the pressure vessel to the reactor, and pressurized gas is supplied from a compressor through a second conduit to the gas volume. A third conduit, comprising a hot gas discharge, carries gases from the reactor, through a filter, and ultimately to a turbine. During normal operation of the plant, pressurized gas is withdrawn from the gas volume through the first conduit and introduced into the reactor at a substantially continuously controlled rate as the primary gas to the reactor. In response to an operational disturbance of the plant, the flow of gas in the first, second, and third conduits is terminated, and thereafter the pressure in the gas volume and in the reactor is substantially simultaneously reduced by opening pressure relief valves in the first and third conduits, and optionally by passing air directly from the second conduit to the turbine.

Isaksson, Juhani (Karhula, FI)

1996-01-01T23:59:59.000Z

176

Sapphire tube pressure vessel  

DOE Patents [OSTI]

A pressure vessel is provided for observing corrosive fluids at high temperatures and pressures. A transparent Teflon bag contains the corrosive fluid and provides an inert barrier. The Teflon bag is placed within a sapphire tube, which forms a pressure boundary. The tube is received within a pipe including a viewing window. The combination of the Teflon bag, sapphire tube and pipe provides a strong and inert pressure vessel. In an alternative embodiment, tie rods connect together compression fittings at opposite ends of the sapphire tube.

Outwater, John O. (Cambridge, MA)

2000-01-01T23:59:59.000Z

177

Title Quantum Optics and Heavy Ion Physics  

E-Print Network [OSTI]

I shall try to say a few words about two particular ways in which my own work has a certain relation to your work with heavy ions. My title is therefore "Quantum Optics and Heavy Ion Physics".

Roy J. Glauber

2006-04-10T23:59:59.000Z

178

Heavy quarks in effective field theories  

E-Print Network [OSTI]

Heavy quark physics serves as a probe to understand QCD, measure standard model parameters, and look for signs of new physics. We study several aspects of heavy quark systems in an effective field theory framework, including ...

Jain, Ambar

2009-01-01T23:59:59.000Z

179

Strangeness signals in heavy ion collisions  

SciTech Connect (OSTI)

The experimental data on strange meson and strange baryon production in relativistic heavy ion collisions are reviewed.

Remsberg, L.P.

1992-11-01T23:59:59.000Z

180

Strangeness signals in heavy ion collisions  

SciTech Connect (OSTI)

The experimental data on strange meson and strange baryon production in relativistic heavy ion collisions are reviewed.

Remsberg, L.P.

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Heavy quark physics from LEP  

SciTech Connect (OSTI)

A review of some of the latest results on heavy flavor physics from the LEP Collaborations is presented. The emphasis is on B physics, particularly new results and those where discrepancies is given of the many techniques which have been developed to permit these analyses.

Dornan, P.J. [Imperial College of Science Technology and Medicine, London (United Kingdom)

1997-01-01T23:59:59.000Z

182

The Search for Heavy Elements  

ScienceCinema (OSTI)

The 1994 documentary "The Search for Heavy Elements" chronicles the expansion of the periodic table through the creation at Berkeley Lab of elements heavier than uranium. The documentary features a mix of rarely-seen archival footage, historical photos, and interviews with scientists who made history, such as Glenn Seaborg and Albert Ghiorso.

None

2010-01-08T23:59:59.000Z

183

FREE CONVECTIVE LAMINAR FLOW WITHIN THE TROMBE WALL CHANNEL  

E-Print Network [OSTI]

LAMINAR FLOW WITHIN THE TROMBE WALL CHANNEL H. Akbarf andLAMINAR FLOW WITHIN THE TROMBE WALL CHANNEL H. Akbari andchannel surfaces of the Trombe wall has been investigated.

Akbari, H.

2011-01-01T23:59:59.000Z

184

Ratios of heavy baryons to heavy mesons in relativistic nucleus-nucleus collisions  

E-Print Network [OSTI]

Heavy baryon/meson ratios Lambda(c)/D(0) and Lambda(b)/(B) over bar (0) in relativistic heavy ion collisions are studied in the quark coalescence model. For heavy baryons, we include production from coalescence of heavy quarks with free light quarks...

Oh, Yongseok; Ko, Che Ming; Lee, Su Houng; Yasui, Shigehiro.

2009-01-01T23:59:59.000Z

185

The Heavy Ion Fusion Science Virtual National Laboratory Status of heavy-ion-beam-driven  

E-Print Network [OSTI]

-see http://videos.komando.com/2008/08/19/water-painting/]. #12;12/7/08 The Heavy Ion Fusion Science Virtual12/7/08 The Heavy Ion Fusion Science Virtual National Laboratory 1 Status of heavy-ion-beam-driven high energy density physics and fusion* Presented by B. Grant Logan on behalf of the U.S. Heavy Ion

186

DIESEL/HEAVY The diesel/heavy equipment certificate offers training in maintenance  

E-Print Network [OSTI]

DIESEL/HEAVY EQUIPMENT The diesel/heavy equipment certificate offers training in maintenance and repair of heavy equipment and trucks. Students will learn to work on electrical and air systems, diesel · Small Engines · Automotive Maintenance · Welding · Training for entry level heavy diesel equipment

Ickert-Bond, Steffi

187

Mathematical modeling of clearance between wall of coke oven and coke cake  

SciTech Connect (OSTI)

A mathematical model was developed for estimating the clearance between the wall of the coke oven and the coke cake. The prediction model is based on the balance between the contractile force and the coking pressure. A clearance forms when the contractile force exceeds the coking pressure in this model. The contractile force is calculated in consideration of the visco-elastic behavior of the thermal shrinkage of the coke. The coking pressure is calculated considering the generation and dispersion of gas in the melting layer. The relaxation time off coke used in this model was obtained with a dilatometer under the load application. The clearance was measured by the laser sensor, and the internal gas pressure was measured in a test oven. The clearance calculated during the coking process were in good agreement with the experimental results, which supported the validity of the mathematical model.

Nushiro, K.; Matsui, T.; Hanaoka, K.; Igawa, K.; Sorimachi, K.

1995-12-01T23:59:59.000Z

188

You have remarkable ideas. share them at the Falling Walls lab!  

E-Print Network [OSTI]

of the falling wallS lab + conference berlin 8/9 nov 2012 aPPlYnoW!www.falling-walls.com/lab THE FALLING WALLS

Heermann, Dieter W.

189

Light-Quark Decays in Heavy Hadrons  

E-Print Network [OSTI]

We consider weak decays of heavy hadrons (bottom and charmed) where the heavy quark acts as a spectator. Theses decays are heavily phase-space suppressed but may become experimentally accessible in the near future. These decays are interesting as a QCD laboratory to study the behaviour of the light quarks in the colour-background field of the heavy spectator.

Faller, Sven

2015-01-01T23:59:59.000Z

190

Heavy Quark Production in ep Collisions  

E-Print Network [OSTI]

Heavy Quark Production in ep Collisions o Introduction o Charm Production o Beauty Production o in ep collisions 23 February 2007 2/17 Heavy Flavor Production Boson-Gluon Fusion, dominant process Hard of the proton: #12;G. Leibenguth, Heavy Quarks Production in ep collisions 23 February 2007 3/17 HERA, Electron

191

3, 37453768, 2003 Heavy hydrogen in  

E-Print Network [OSTI]

ACPD 3, 3745­3768, 2003 Heavy hydrogen in the stratosphere T. R¨ockmann et al. Title Page Abstract/3745/ © European Geosciences Union 2003 Atmospheric Chemistry and Physics Discussions Heavy hydrogen Heavy hydrogen in the stratosphere T. R¨ockmann et al. Title Page Abstract Introduction Conclusions

Paris-Sud XI, Université de

192

Hydrogenation of single-walled carbon nanotubes  

E-Print Network [OSTI]

Towards the development of a useful mechanism for hydrogen storage, we have studied the hydrogenation of single-walled carbon nanotubes with atomic hydrogen using core-level photoelectron spectroscopy and x-ray absorption spectroscopy. We find that atomic hydrogen creates C-H bonds with the carbon atoms in the nanotube walls and such C-H bonds can be com-pletely broken by heating to 600 oC. We demonstrate approximately 65+/-15 at % hydrogenation of carbon atoms in the single-walled carbon nanotubes which is equivalent to 5.1+/-1.2 weight % hydrogen capacity. We also show that the hydrogenation is a reversible process.

Anton Nikitin; Hirohito Ogasawara; David Mann; Reinhard Denecke; Zhiyong Zhang; Hongjie Dai; KJ Cho; Anders Nilsson

2005-10-14T23:59:59.000Z

193

Highway noise reduction by barrier walls  

E-Print Network [OSTI]

's Variables 3. Noise Reduction and Noise Reduction Factor 4. Relationship Between Noise Attenuation and d 5. Rettinger's Variables 6. Relationship of Sound-Level Reduction and v 7. Basic Principles in Sound-Transmission Loss 8. The Mass Law Relationship... that the barrier wall is acoustically opaque (i. e. , impermeable to sound waves). Purcell (8) found that the noise transmission loss of a wall was a measure of the ratio of the acoustical energy transmitted through the wall to the acoustical energy incident...

Young, Murray F

1971-01-01T23:59:59.000Z

194

Confinement of hydrogen at high pressure in carbon nanotubes  

DOE Patents [OSTI]

A high pressure hydrogen confinement apparatus according to one embodiment includes carbon nanotubes capped at one or both ends thereof with a hydrogen-permeable membrane to enable the high pressure confinement of hydrogen and release of the hydrogen therethrough. A hydrogen confinement apparatus according to another embodiment includes an array of multi-walled carbon nanotubes each having first and second ends, the second ends being capped with palladium (Pd) to enable the high pressure confinement of hydrogen and release of the hydrogen therethrough as a function of palladium temperature, wherein the array of carbon nanotubes is capable of storing hydrogen gas at a pressure of at least 1 GPa for greater than 24 hours. Additional apparatuses and methods are also presented.

Lassila, David H. (Aptos, CA); Bonner, Brian P. (Livermore, CA)

2011-12-13T23:59:59.000Z

195

Security Walls, LLC, January 14-18, 2013  

Broader source: Energy.gov (indexed) [DOE]

their contributions to health and safety at Security Walls. Security Walls uses the Job Hazard Analysis process to address protective force hazards and develop controls. Subject...

196

Sorted Single-Walled Carbon Nanotube Films for Transparent Electrodes...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Sorted Single-Walled Carbon Nanotube Films for Transparent Electrodes in Organic Solar Cells Home > Research > ANSER Research Highlights > Sorted Single-Walled Carbon Nanotube...

197

Building America Special Research Project: High-R Walls Case...  

Office of Environmental Management (EM)

Building America Special Research Project: High-R Walls Case Study Analysis Building America Special Research Project: High-R Walls Case Study Analysis This report considers a...

198

Single Wall Diesel Particulate Filter (DPF) Filtration Efficiency...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Single Wall Diesel Particulate Filter (DPF) Filtration Efficiency Studies Using Laboratory Generated Particles. Single Wall Diesel Particulate Filter (DPF) Filtration Efficiency...

199

Active control of underground stresses through rock pressurization  

SciTech Connect (OSTI)

To significantly increase the stability of underground excavations while exploiting the full advantages of confined rock strength, methods must be developed to actively control the distribution of stresses near the excavation. This US Bureau of Mines study examines theoretical and practical aspects of rock pressurization, an active stress control concept that induces compressive stress in the wall rock through repeated hydraulic fracturing with a settable fluid. Numerical analyses performed by incorporating the rock pressurization concept into a variety of boundary-element models indicate that rock pressurization has the potential to improve underground excavation stability in three ways: (1) by relocating stress concentrations away from the weak opening surface to stronger, confined wall rock; (2) by inducing additional stresses in a biaxial stress field to reduce the difference between the principal stress components near the surface of the opening, and (3) by counteracting the tensile stresses induced in the rock around internally loaded openings. Practical aspects of the rock pressurization concept were investigated through a series of hydraulic fracturing experiments. The use of sulfur as a settable fluid for hydraulic fracturing was demonstrated, although problems related to sulfur viscosity suggest that other molten materials, such as wax, may be better suited to practical field application of the rock pressurization concept.

Vandergrift, T.L.

1995-06-01T23:59:59.000Z

200

See through walls with Wi-Fi  

E-Print Network [OSTI]

Wi-Fi signals are typically information carriers between a transmitter and a receiver. In this thesis, we show that Wi-Fi can also extend our senses, enabling us to see moving objects through walls and behind closed doors. ...

Adib, Fadel

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

See through walls with WiFi!  

E-Print Network [OSTI]

Wi-Fi signals are typically information carriers between a transmitter and a receiver. In this paper, we show that Wi-Fi can also extend our senses, enabling us to see moving objects through walls and behind closed doors. ...

Adib, Fadel M.

2013-01-01T23:59:59.000Z

202

Nonextensive statistical dynamics applied to wall turbulence  

E-Print Network [OSTI]

We apply a formalism of nonextensive statistical mechanics to experimental wall turbulence data, for the first time to our knowledge. Wind tunnel data for velocity differences a streamwise distance $r$ apart are compared to the prediction from theory as developed by Beck. The simplest theory, in which all free parameters are removed, is found to reproduce statistics for the wall-normal velocity component remarkably well, even for $r$ well beyond the corresponding integral scale, while the corresponding description of the streamwise velocity fluctuations is reasonable at separations below the integral scale. A least-squares 2-parameter fit is performed, and the dependence of the optimum parameter values on wall separation and $r$ is analysed. Both parameters are found to be approximately independent of wall-separation in the logarithmic sub-layer.

Simen Å Ellingsen; Per-Åge Krogstad

2014-02-10T23:59:59.000Z

203

Beautify Your Windows and Glass Walls.  

E-Print Network [OSTI]

-utside? How do your dqkrie outside of your house? 2 IlnKY color affect , Coloor, De~kn and Tex When choosing draperies to har- monize with a room, consider the room, proportions, exposure, view, walls, floors, furnishings, accessories...

Tompkins, Charlotte

1961-01-01T23:59:59.000Z

204

Anisotropic Expansion of the Plant Cell Wall  

E-Print Network [OSTI]

solar panels of leaves to the coiled grap- pling hooks of tendrils. Thompson (1917) re- alized of a unit area of cell wall is characterized by the direction and degree of anisotropy. The direction

Baskin, Tobias

205

Hadron Production in Heavy Ion Collisions  

SciTech Connect (OSTI)

Heavy ion collisions are an ideal tool to explore the QCD phase diagram. The goal is to study the equation of state (EOS) and to search for possible in-medium modifications of hadrons. By varying the collision energy a variety of regimes with their specific physics interest can be studied. At energies of a few GeV per nucleon, the regime where experiments were performed first at the Berkeley Bevalac and later at the Schwer-Ionen-Synchrotron (SIS) at GSI in Darmstadt, we study the equation of state of dense nuclear matter and try to identify in-medium modifications of hadrons. Towards higher energies, the regime of the Alternating Gradient Synchrotron (AGS) at the Brookhaven National Laboratory (BNL), the Super-Proton Synchrotron (SPS) at CERN, and the Relativistic Heavy Ion Collider (RHIC) at BNL, we expect to produce a new state of matter, the Quark-Gluon Plasma (QGP). The physics goal is to identify the QGP and to study its properties. By varying the energy, different forms of matter are produced. At low energies we study dense nuclear matter, similar to the type of matter neutron stars are made of. As the energy is increased the main constituents of the matter will change. Baryon excitations will become more prevalent (resonance matter). Eventually we produce deconfined partonic matter that is thought to be in the core of neutron stars and that existed in the early universe. At low energies a great variety of collective effects is observed and a rather good understanding of the particle production has been achieved, especially that of the most abundantly produced pions and kaons. Many observations can be interpreted as time-ordered emission of various particle species. It is possible to determine, albeit model dependent, the equation of state of nuclear matter. We also have seen indications, that the kaon mass, especially the mass of the K{sup +}, might be modified by the medium created in heavy ion collisions. At AGS energies and above, emphasis shifts towards different aspects. Lattice QCD calculations predict the transition between a Quark-Gluon Plasma and a hadronic state at a critical temperature, T{sub c}, of about 150 to 190 MeV at vanishing baryon density. The energy density at the transition point is about 1:0 GeV/fm{sup 3}. It is generally assumed that chiral symmetry restoration happens simultaneously. In the high-energy regime, especially at RHIC, a rich field of phenomena [3] has revealed itself. Hot and dense matter with very strong collectivity has been created. There are indications that collectivity develops at the parton level, i.e. at a very early stage of the collision, when the constituents are partons rather than hadrons. Signs of pressure driven collective effects are our main tool for the study of the EOS. There are also strong indications that in the presence of a medium hadronization occurs through the process of quark coalescence and not through quark fragmentation, the process dominant for high-energy p+p reactions. We limit this report to the study of hadrons emitted in heavy ion reactions. The report is divided into two parts. The first part describes the phenomena observed from hadrons produced at low energies, whereas the second part concentrates on the search for signs of a partonic state at high energies.

Ritter, Hans Georg; Xu, Nu

2009-05-19T23:59:59.000Z

206

Open heavy flavor production at RHIC  

E-Print Network [OSTI]

The study of heavy flavor production in relativistic heavy ion collisions is an extreme experimental challenge but provides important information on the properties of the Quark-Gluon Plasma (QGP) created in Au+Au collisions at RHIC. Heavy-quarks are believed to be produced in the initial stages of the collision, and are essential on the understanding of parton energy loss in the dense medium created in such environment. Moreover, heavy-quarks can help to investigate fundamental properties of QCD in elementary p+p collisions. In this work we review recent results on heavy flavor production and their interaction with the hot and dense medium at RHIC.

A. A. P. Suaide

2007-02-16T23:59:59.000Z

207

Thin Wall Cast Iron: Phase II  

SciTech Connect (OSTI)

The development of thin-wall technology allows the designers of energy consuming equipment to select the most appropriate material based on cost/material properties considerations, and not solely on density. The technology developed in this research project will permit the designers working for the automotive industry to make a better informed choice between competing materials and thin wall cast iron, thus decreasing the overall cost of the automobile.

Doru M. Stefanescu

2005-07-21T23:59:59.000Z

208

Electric and Magnetic Walls on Dielectric Interfaces  

E-Print Network [OSTI]

Sufficient conditions of the existence of electric or magnetic walls on dielectric interfaces are given for a multizone uniform dielectric waveguiding system. If one of two adjacent dielectric zones supports a TEM field distribution while the other supports a TM (TE) field distribution, then the common dielectric interface behaves as an electric (magnetic) wall, that is, the electric (magnetic) field line is perpendicular to the interface while the magnetic (electric) field line is parallel to the interface.

Changbiao Wang

2010-07-20T23:59:59.000Z

209

INTOR impurity control and first wall system  

SciTech Connect (OSTI)

The highlights of the recent INTOR effort on examining the key issues of the impurity control/first wall system are summarized. The emphasis of the work was an integrated study of the edge-region physics, plasma-wall interaction, materials, engineering and magnetic considerations associated with the poloidal divertor and pump limiter. The development of limiter and divertor collector plate designs with an acceptable lifetime was a major part of the work.

Abdou, M.A.

1983-04-01T23:59:59.000Z

210

RESEARCH OIL RECOVERY MECHANISMS IN HEAVY OIL RESERVOIRS  

SciTech Connect (OSTI)

The United States continues to rely heavily on petroleum fossil fuels as a primary energy source, while domestic reserves dwindle. However, so-called heavy oil (10 to 20{sup o}API) remains an underutilized resource of tremendous potential. Heavy oils are much more viscous than conventional oils. As a result, they are difficult to produce with conventional recovery methods such as pressure depletion and water injection. Thermal recovery is especially important for this class of reservoirs because adding heat, usually via steam injection, generally reduces oil viscosity dramatically. This improves displacement efficiency. The research described here was directed toward improved understanding of thermal and heavy-oil production mechanisms and is categorized into: (1) flow and rock properties; (2) in-situ combustion; (3) additives to improve mobility control; (4) reservoir definition; and (5) support services. The scope of activities extended over a three-year period. Significant work was accomplished in the area of flow properties of steam, water, and oil in consolidated and unconsolidated porous media, transport in fractured porous media, foam generation and flow in homogeneous and heterogeneous porous media, the effects of displacement pattern geometry and mobility ratio on oil recovery, and analytical representation of water influx. Significant results are described.

Anthony R. Kovscek; William E. Brigham

1999-06-01T23:59:59.000Z

211

Process for converting heavy oil deposited on coal to distillable oil in a low severity process  

DOE Patents [OSTI]

A process for removing oil from coal fines that have been agglomerated or blended with heavy oil comprises the steps of heating the coal fines to temperatures over 350.degree. C. up to 450.degree. C. in an inert atmosphere, such as steam or nitrogen, to convert some of the heavy oil to lighter, and distilling and collecting the lighter oils. The pressure at which the process is carried out can be from atmospheric to 100 atmospheres. A hydrogen donor can be added to the oil prior to deposition on the coal surface to increase the yield of distillable oil.

Ignasiak, Teresa (417 Heffernan Drive, Edmonton, Alberta, CA); Strausz, Otto (13119 Grand View Drive, Edmonton, Alberta, CA); Ignasiak, Boleslaw (417 heffernan Drive, Edmonton, Alberta, CA); Janiak, Jerzy (17820 - 76 Ave., Edmonton, Alberta, CA); Pawlak, Wanda (3046 - 11465 - 41 Avenue, Edmonton, Alberta, CA); Szymocha, Kazimierz (3125 - 109 Street, Edmonton, Alberta, CA); Turak, Ali A. (Edmonton, CA)

1994-01-01T23:59:59.000Z

212

Master external pressure charts  

SciTech Connect (OSTI)

This paper presents a method to develop master external pressure charts from which individual external pressure charts for each material specification may be derived. The master external charts can represent a grouping of materials with similar chemical composition, similar stress-strain curves but produced to different strength levels. External pressure charts are used by various Sections of the ASME Boiler and Pressure Vessel and Piping Codes to design various components such as cylinders, sphered, formed heads, tubes, piping, rings and other components, subjected to external pressure or axial compression loads. These charts are pseudo stress-strain curves for groups of materials with similar stress-strain shapes. The traditional approach was originally developed in the 1940`s and is a graphical approach where slopes to the strain curves are drawn graphically from which pseudo-strain levels are calculated. The new method presented in this paper develops mathematical relationships for the material stress-strain curves and the external pressure charts. The method has the ability to calculate stress-strain curves from existing external pressure charts. The relationships are a function of temperature, the modulus of elasticity, yield strength, and two empirical material constants. In this approach, conservative assumptions used to assign materials to lower bound external pressure charts can be removed. This increases the buckling strength capability of many materials in the Code, providing economic benefits while maintaining the margin of safety specified by the Code criteria. The method can also reduce the number of material charts needed in the Code and provides for the capability to extend the existing pressure charts to higher design temperatures. The new method is shown to contain a number of improvements over the traditional approach and is presently under consideration by appropriate ASME Code committees.

Michalopoulos, E. [Hartford Steam Boiler Inspection and Insurance Co., CT (United States). Codes and Standards Dept.

1996-12-01T23:59:59.000Z

213

Central collisions of heavy ions  

SciTech Connect (OSTI)

This report describes the activities of the Heavy Ion Physics Group at the University of California, Riverside from October 1, 1991 to September 30, 1992. During this period, the program focused on particle production at AGS energies, and correlation studies at the Bevalac in nucleus-nucleus central collisions. As part of the PHENIX collaboration, contributions were made to the Preliminary Conceptual Design Report (pCDR), and work on a RHIC silicon microstrip detector R D project was performed.

Fung, Sun-yiu.

1992-10-01T23:59:59.000Z

214

Capacitance pressure sensor  

DOE Patents [OSTI]

A microelectromechanical (MEM) capacitance pressure sensor integrated with electronic circuitry on a common substrate and a method for forming such a device are disclosed. The MEM capacitance pressure sensor includes a capacitance pressure sensor formed at least partially in a cavity etched below the surface of a silicon substrate and adjacent circuitry (CMOS, BiCMOS, or bipolar circuitry) formed on the substrate. By forming the capacitance pressure sensor in the cavity, the substrate can be planarized (e.g. by chemical-mechanical polishing) so that a standard set of integrated circuit processing steps can be used to form the electronic circuitry (e.g. using an aluminum or aluminum-alloy interconnect metallization).

Eaton, William P. (Tijeras, NM); Staple, Bevan D. (Albuquerque, NM); Smith, James H. (Albuquerque, NM)

2000-01-01T23:59:59.000Z

215

High pressure counterflow CHF.  

E-Print Network [OSTI]

This is a report of the experimental results of a program in countercurrent flow critical heat flux. These experiments were performed with Freon 113 at 200 psia in order to model a high pressure water system. An internally ...

Walkush, Joseph Patrick

1975-01-01T23:59:59.000Z

216

Nonlinear optomechanical pressure  

E-Print Network [OSTI]

A transparent material exhibits ultra-fast optical nonlinearity and is subject to optical pressure if irradiated by a laser beam. However, the effect of nonlinearity on optical pressure is often overlooked, even if a nonlinear optical pressure may be potentially employed in many applications, as optical manipulation, biophysics, cavity optomechanics, quantum optics, optical tractors, and is relevant in fundamental problems as the Abraham-Minkoswky dilemma, or the Casimir effect. Here we show that an ultra-fast nonlinear polarization gives indeed a contribution to the optical pressure that also is negative in certain spectral ranges; the theoretical analysis is confirmed by first-principles simulations. An order of magnitude estimate shows that the effect can be observable by measuring the deflection of a membrane made by graphene.

Claudio Conti; Robert Boyd

2014-03-15T23:59:59.000Z

217

Near-wall modeling of an isothermal vertical wall using one-dimensional turbulence  

E-Print Network [OSTI]

[5]. The challenge in modeling this class of flows is the coupling between the heat transfer approaches are considered for describing the heat transfer from a vertical isothermal wall. In this approach at the wall surface and the generation of turbulence from buoyancy forces, which in turn, affect

DesJardin, Paul E.

218

Effect of pressure gradient on the drag reduction performance of two and three dimensional riblets  

E-Print Network [OSTI]

Integral Parameters . 4. 2 Law of the Wall Profiles 4. 3 Pressure Gradient Parameters 4. 4 Preston Tube Measurements 4. 5 Roughness Function 4. 6 Growth of the Internal Layer 4. 7 Turbulence Measurements 4. 7. 1 Turbulence intensity 4. 7. 2 Third.... 4 Spectra for favorable pressure gradient 4. 8. 5 Roughness effects on the bursting process V CONCLUSION . REFERENCES APPENDIX A APPENDIX B 50 50 51 94 134 175 177 180 183 . . 185 VITA . . 210 LIST OF FIGURES Figure 1. Proportions...

Hall, Aaron Chenault

1991-01-01T23:59:59.000Z

219

Thermodynamics of free Domain Wall fermions  

E-Print Network [OSTI]

Studying various thermodynamic quantities for the free domain wall fermions for both finite and infinite fifth dimensional extent N_5, we find that the lattice corrections are minimum for $N_T\\geq10$ for both energy density and susceptibility, for its irrelevant parameter M in the range 1.45-1.50. The correction terms are, however, quite large for small lattice sizes of $N_T\\leq8$. We propose modifications of the domain wall operator, as well as the overlap operator, to reduce the finite cut-off effects to within 10% of the continuum results of the thermodynamic quantities for the currently used N_T=6-8 lattices. Incorporating chemical potential, we show that \\mu^2 divergences are absent for a large class of such domain wall fermion actions although the chiral symmetry is broken for $\\mu\

R. V. Gavai; Sayantan Sharma

2008-11-19T23:59:59.000Z

220

Wall thickness measuring method and apparatus  

DOE Patents [OSTI]

An apparatus for measuring the wall thickness of a nonmagnetic article having a housing supporting a magnet and a contiguous supporting surface. The tubular article and the housing are releasably secured to the supporting surface and a support member of an optical comparator, respectively. To determine the wall thickness of the article at a selected point, a magnetically responsive ball is positioned within the tubular article over said point and retained therein by means of a magnetic field produced by the magnet. Thereafter, an optical comparator is employed to project a magnified image of the ball on a screen and the wall thickness at the selected point is calculated by using a ball surface measurement taken with the comparator in conjunction with a previously determined base line measurement.

Salzer, L.J.; Bergren, D.A.

1987-10-06T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Wall thickness measuring method and apparatus  

DOE Patents [OSTI]

An apparatus for measuring the wall thickness of a nonmagnetic article having a housing supporting a magnet and a contiguous supporting surface. The tubular article and the housing are releasably secured to the supporting surface and a support member of an optical comparator, respectively. To determine the wall thickness of the article at a selected point, a magnetically responsive ball is positioned within the tubular article over said point and retained therein by means of a magnetic field produced by the magnet. Thereafter, an optical comparator is employed to project a magnified image of the ball on a screen and the wall thickness at the selected point is calculated by using a ball surface measurement taken with the comparator in conjunction with a previously determined base line measurement.

Salzer, Leander J. (Los Alamos, NM); Bergren, Donald A. (Los Alamos, NM)

1989-01-01T23:59:59.000Z

222

Turbine airfoil with a compliant outer wall  

DOE Patents [OSTI]

A turbine airfoil usable in a turbine engine with a cooling system and a compliant dual wall configuration configured to enable thermal expansion between inner and outer layers while eliminating stress formation in the outer layer is disclosed. The compliant dual wall configuration may be formed a dual wall formed from inner and outer layers separated by a support structure. The outer layer may be a compliant layer configured such that the outer layer may thermally expand and thereby reduce the stress within the outer layer. The outer layer may be formed from a nonplanar surface configured to thermally expand. In another embodiment, the outer layer may be planar and include a plurality of slots enabling unrestricted thermal expansion in a direction aligned with the outer layer.

Campbell, Christian X. (Oviedo, FL); Morrison, Jay A. (Oviedo, FL)

2012-04-03T23:59:59.000Z

223

INTEGRATED ENERGY EFFICIENT WINDOW-WALL SYSTEMS  

SciTech Connect (OSTI)

The building industry faces the challenge of reducing energy use while simultaneously improving construction methods and marketability. This paper describes the first phase of a project to address these concerns by designing an Integrated Window Wall System (IWWS) that can be commercialized. This work builds on previous research conducted during the 1990's by Lawrence Berkeley national Laboratories (LBNL). During this phase, the objective was to identify appropriate technologies, problems and issues and develop a number of design concepts. Four design concepts were developed into prototypes and preliminary energy analyses were conducted Three of these concepts (the foam wall, steel wall, and stiffened plate designs) showed particular potential for meeting the project objectives and will be continued into a second phase where one or two of the systems will be brought closer to commercialization.

Michael Arney, Ph.D.

2002-12-31T23:59:59.000Z

224

Passive blast pressure sensor  

DOE Patents [OSTI]

A passive blast pressure sensor for detecting blast overpressures of at least a predetermined minimum threshold pressure. The blast pressure sensor includes a piston-cylinder arrangement with one end of the piston having a detection surface exposed to a blast event monitored medium through one end of the cylinder and the other end of the piston having a striker surface positioned to impact a contact stress sensitive film that is positioned against a strike surface of a rigid body, such as a backing plate. The contact stress sensitive film is of a type which changes color in response to at least a predetermined minimum contact stress which is defined as a product of the predetermined minimum threshold pressure and an amplification factor of the piston. In this manner, a color change in the film arising from impact of the piston accelerated by a blast event provides visual indication that a blast overpressure encountered from the blast event was not less than the predetermined minimum threshold pressure.

King, Michael J.; Sanchez, Roberto J.; Moss, William C.

2013-03-19T23:59:59.000Z

225

Propagation of an atmospheric pressure plasma plume  

SciTech Connect (OSTI)

The ''plasma bullet'' behavior of atmospheric pressure plasma plumes has recently attracted significant interest. In this paper, a specially designed plasma jet device is used to study this phenomenon. It is found that a helium primary plasma can propagate through the wall of a dielectric tube and keep propagating inside the dielectric tube (secondary plasma). High-speed photographs show that the primary plasma disappears before the secondary plasma starts to propagate. Both plumes propagate at a hypersonic speed. Detailed studies on the dynamics of the plasma plumes show that the local electric field induced by the charges on the surface of the dielectric tube plays an important role in the ignition of the secondary plasma. This indicates that the propagation of the plasma plumes may be attributed to the local electric field induced by the charges in the bulletlike plasma volume.

Lu, X.; Xiong, Q.; Xiong, Z.; Hu, J.; Zhou, F.; Gong, W.; Xian, Y.; Zou, C.; Tang, Z.; Jiang, Z.; Pan, Y. [College of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China)

2009-02-15T23:59:59.000Z

226

Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

ce001musculus2012o.pdf More Documents & Publications Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty Combustion Modeling Vehicle Technologies Office Merit Review...

227

Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

D.C. ace01musculus.pdf More Documents & Publications Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty Combustion Modeling Vehicle Technologies Office Merit Review...

228

Wood Pulp Digetster Wall Corrosion Investigation  

SciTech Connect (OSTI)

The modeling of the flow in a wood pulp digester is but one component of the investigation of the corrosion of digesters. This report describes the development of a Near-Wall-Model (NWM) that is intended to couple with a CFD model that determines the flow, heat, and chemical species transport and reaction within the bulk flow of a digester. Lubrication theory approximations were chosen from which to develop a model that could determine the flow conditions within a thin layer near the vessel wall using information from the interior conditions provided by a CFD calculation of the complete digester. The other conditions will be determined by coupled solutions of the wood chip, heat, and chemical species transport and chemical reactions. The NWM was to couple with a digester performance code in an iterative fashion to provide more detailed information about the conditions within the NW region. Process Simulations, Ltd (PSL) is developing the digester performance code. This more detailed (and perhaps more accurate) information from the NWM was to provide an estimate of the conditions that could aggravate the corrosion at the wall. It is intended that this combined tool (NWM-PSL) could be used to understand conditions at/near the wall in order to develop methods to reduce the corrosion. However, development and testing of the NWM flow model took longer than anticipated and the other developments (energy and species transport, chemical reactions and linking with the PSL code) were not completed. The development and testing of the NWM are described in this report. In addition, the investigation of the potential effects of a clear layer (layer reduced in concentration of wood chips) near the wall is reported in Appendix D. The existence of a clear layer was found to enhance the flow near the wall.

Giles, GE

2003-09-18T23:59:59.000Z

229

Emission Controls for Heavy-Duty Trucks  

Broader source: Energy.gov (indexed) [DOE]

DEER Conference Emission Controls for Heavy-Duty Trucks Overview Emission Standards - US and Worldwide Technology Options for Meeting Emissions System Integration ...

230

Heavy Water Test Reactor Dome Removal  

SciTech Connect (OSTI)

A high speed look at the removal of the Heavy Water Test Reactor Dome Removal. A project sponsored by the Recovery Act on the Savannah River Site.

None

2011-01-01T23:59:59.000Z

231

Demonstration of Automated Heavy-Duty Vehicles  

E-Print Network [OSTI]

a future in which vehicle automation technologies are ableto support the heavy vehicle automation including PrecisionCommittee on Vehicle-Highway Automation, and the attendees

2006-01-01T23:59:59.000Z

232

Heavy flavor production in the STAR experiment  

E-Print Network [OSTI]

In this paper, recent STAR heavy flavor measurements in proton-proton and heavy-ion collisions are highlighted. We report studies of open charm mesons, reconstructed directly from hadronic decay products, and studies of electrons from semi-leptonic decays of heavy flavor hadrons. We also present J/$\\psi$ measurements via the di-electron decay channel at various collision systems and energies. In Au+Au collisions the energy dependence of J/$\\psi$ production measured at $\\sqrt{s_{NN}}$ = 39, 62.4 and 200 GeV is shown. Finally, prospects of heavy flavor measurements with the STAR detector upgrades are discussed.

Barbara Trzeciak; for the STAR Collaboration

2014-09-11T23:59:59.000Z

233

Heavy Oil Consumption Reduction Program (Quebec, Canada)  

Broader source: Energy.gov [DOE]

This program helps heavy oil consumers move toward sustainable development while improving their competitive position by reducing their consumption. Financial assistance is offered to carry out...

234

Department of Energy and Electrical Engineering Spring 2012 Heavy-Duty Diesel Engine Friction Reduction Testing and Analysis  

E-Print Network [OSTI]

PENNSTATE Department of Energy and Electrical Engineering Spring 2012 Heavy-Duty Diesel Engine and pumping frictional losses on Volvo-Mack's 11 liter Diesel Engine. Thermocouples and pressure transducers is to quantify friction losses on Volvo's current 11-liter engine model. Team members will remove hardware

Demirel, Melik C.

235

Standing gravitational waves from domain walls  

SciTech Connect (OSTI)

We construct a plane symmetric, standing gravitational wave for a domain wall plus a massless scalar field. The scalar field can be associated with a fluid which has the properties of 'stiff' matter, i.e., matter in which the speed of sound equals the speed of light. Although domain walls are observationally ruled out in the present era, the solution has interesting features which might shed light on the character of exact nonlinear wave solutions to Einstein's equations. Additionally this solution may act as a template for higher dimensional 'brane-world' model standing waves.

Gogberashvili, Merab [Andronikashvili Institute of Physics, 6 Tamarashvili Street, Tbilisi 0177 (Georgia); Javakhishvili Tbilisi State University, 3 Chavchavadze Avenue, Tbilisi 0128 (Georgia); California State University, Fresno, Physics Department, Fresno, California 93740-8031 (United States); Myrzakul, Shynaray [Department of General and Theoretical Physics, Gumilev Eurasian National University, Astana, 010008 (Kazakhstan); California State University, Fresno, Physics Department, Fresno, California 93740-8031 (United States); Singleton, Douglas [California State University, Fresno, Physics Department, Fresno, California 93740-8031 (United States); Institute of Gravitation and Cosmology, Peoples' Friendship University of Russia, Moscow 117198 (Russian Federation)

2009-07-15T23:59:59.000Z

236

Enhancement of wall jet transport properties  

DOE Patents [OSTI]

By enhancing the natural instabilities in the boundary layer and in the free shear layer of a wall jet, the boundary is minimized thereby increasing the transport of heat and mass. Enhancing the natural instabilities is accomplished by pulsing the flow of air that creates the wall jet. Such pulsing of the flow of air can be accomplished by sequentially occluding and opening a duct that confines and directs the flow of air, such as by rotating a disk on an axis transverse to the flow of air in the duct. 17 figs.

Claunch, S.D.; Farrington, R.B.

1997-02-04T23:59:59.000Z

237

Non-Abelian Webs of Walls  

E-Print Network [OSTI]

Domain wall junctions are studied in N=2 supersymmetric U(Nc) gauge theory with Nf(>Nc) flavors. We find that all three possibilities are realized for positive, negative and zero junction charges. The positive junction charge is found to be carried by a topological charge in the Hitchin system of an SU(2) gauge subgroup. We establish rules of the construction of the webs of walls. Webs can be understood qualitatively by grid diagram and quantitatively by associating moduli parameters to web configurations.

Minoru Eto; Youichi Isozumi; Muneto Nitta; Keisuke Ohashi; Norisuke Sakai

2005-09-15T23:59:59.000Z

238

Pressure suppression containment system  

DOE Patents [OSTI]

A pressure suppression containment system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and a gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel. The wetwell pool includes a plenum for receiving the non-condensable gas carried with steam from the drywell following a loss-of-coolant-accident (LOCA). The wetwell plenum is vented to a plenum above the GDCS pool following the LOCA for suppressing pressure rise within the containment vessel. A method of operation includes channeling steam released into the drywell following the LOCA into the wetwell pool for cooling along with the non-condensable gas carried therewith. The GDCS pool is then drained by gravity, and the wetwell plenum is vented into the GDCS plenum for channeling the non-condensable gas thereto. 6 figures.

Gluntz, D.M.; Townsend, H.E.

1994-03-15T23:59:59.000Z

239

Oxygen partial pressure sensor  

DOE Patents [OSTI]

A method for detecting oxygen partial pressure and an oxygen partial pressure sensor are provided. The method for measuring oxygen partial pressure includes contacting oxygen to a solid oxide electrolyte and measuring the subsequent change in electrical conductivity of the solid oxide electrolyte. A solid oxide electrolyte is utilized that contacts both a porous electrode and a nonporous electrode. The electrical conductivity of the solid oxide electrolyte is affected when oxygen from an exhaust stream permeates through the porous electrode to establish an equilibrium of oxygen anions in the electrolyte, thereby displacing electrons throughout the electrolyte to form an electron gradient. By adapting the two electrodes to sense a voltage potential between them, the change in electrolyte conductivity due to oxygen presence can be measured. 1 fig.

Dees, D.W.

1994-09-06T23:59:59.000Z

240

Pressure suppression containment system  

DOE Patents [OSTI]

A pressure suppression containment system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and a gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel. The wetwell pool includes a plenum for receiving the non-condensable gas carried with steam from the drywell following a loss-of coolant-accident (LOCA). The wetwell plenum is vented to a plenum above the GDCS pool following the LOCA for suppressing pressure rise within the containment vessel. A method of operation includes channeling steam released into the drywell following the LOCA into the wetwell pool for cooling along with the non-condensable gas carried therewith. The GDCS pool is then drained by gravity, and the wetwell plenum is vented into the GDCS plenum for channeling the non-condensable gas thereto.

Gluntz, Douglas M. (San Jose, CA); Townsend, Harold E. (San Jose, CA)

1994-03-15T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

High temperature solid lubricant materials for heavy duty and advanced heat engines  

SciTech Connect (OSTI)

Advanced engine designs incorporate higher mechanical and thermal loading to achieve efficiency improvements. This approach often leads to higher operating temperatures of critical sliding elements (e.g. piston ring/cylinder wall contacts and valve guides) which compromise the use of conventional and even advanced synthetic liquid lubricants. For these applications solid lubricants must be considered. Several novel solid lubricant composites and coatings designated PS/PM200 have been employed to dry and marginally oil lubricated contacts in advanced heat engines. These applications include cylinder kits of heavy duty diesels, and high temperature sterling engines, sidewall seals of rotary engines and various exhaust valve and exhaust component applications. The following paper describes the tribological and thermophysical properties of these tribomaterials and reviews the results of applying them to engine applications. Other potential tribological materials and applications are also discussed with particular emphasis to heavy duty and advanced heat engines.

DellaCorte, C.; Wood, J.C.

1994-10-01T23:59:59.000Z

242

Plating under reduced pressure  

SciTech Connect (OSTI)

Plating under reduced pressure was evaluated for both electroless nickel and electrodeposited copper systems. The objective was to reduce pitting of these coatings thereby further enhancing their usage for diamond turning applications. Cursory experiments with electroless nickel showed reduced porosity when deposition was done at around 500 torr. Detailed experiments with electrodeposited copper at around 100 torr provided similar results. Scanning tunneling microscopy was effectively used to show the improvement in the copper deposits plated under reduced pressure. Benefits included reduced surface roughness and finer and denser grain structure.

Dini, J.W.; Beat, T.G.; Cowden, W.C. (Lawrence Livermore National Lab., CA (United States)); Ryan, L.E.; Hewitt, W.B. (TRW, Inc., Redondo Beach, CA (United States))

1992-06-01T23:59:59.000Z

243

The Heavy Ion Fusion Virtual National Laboratory The Heavy Ion Path to Fusion Energy  

E-Print Network [OSTI]

-consistent power plant design for a multi- beam induction linac, final focus and chamber propagationThe Heavy Ion Fusion Virtual National Laboratory The Heavy Ion Path to Fusion Energy Grant Logan Director Heavy-Ion Fusion Virtual National Laboratory Presented to FESAC Workshop on Development Paths

244

Heavy Flavour results from Tevatron  

E-Print Network [OSTI]

The CDF and D0 experiments finalize the analysis of their full statistics collected in the $p \\bar p$ collisions at a center-of-mass energy of $\\sqrt{s} = 1.96$ TeV at the Fermilab Tevatron collider. This paper presents several new results on the properties of hadrons containing heavy $b$- and $c$-quarks obtained by both collaborations. These results include the search for the rare decays $B^0, B^0_s \\to \\mu^+ \\mu^-$ (CDF), the study of CP asymmetry in $B_s \\to J\\psi \\phi$ decay (CDF, D0), the measurement of the like-sign dimuon charge asymmetry (D0), the measurement of CP asymmetry in $D^0 \\to K^+K^-$ and $D^0 \\to \\pi^+\\pi^-$ decays (CDF), and the new measurement of the $B_s \\to D_s^{(*)+} D_s^{(*)-}$ branching fraction (CDF). Both experiments still expect to produce more results on the properties of heavy flavours.

G. Borissov

2012-06-21T23:59:59.000Z

245

Cooling and Trapping Atoms Atoms are slowed and cooled by radiation pressure from laser light  

E-Print Network [OSTI]

Cooling and Trapping Atoms Atoms are slowed and cooled by radiation pressure from laser light and then trapped in a bottle whose "walls" are magnetic fields. Cooled atoms are ideal for exploring basic. research has traditionally been the study of the intrinsic prop erties of isolated atoms. In the early part

Johannesson, Henrik

246

Hot wire production of single-wall and multi-wall carbon nanotubes  

DOE Patents [OSTI]

Apparatus (210) for producing a multi-wall carbon nanotube (213) may comprise a process chamber (216), a furnace (217) operatively associated with the process chamber (216), and at least one filament (218) positioned within the process chamber (216). At least one power supply (220) operatively associated with the at least one filament (218) heats the at least one filament (218) to a process temperature. A gaseous carbon precursor material (214) operatively associated with the process chamber (216) provides carbon for forming the multi-wall carbon nanotube (213). A metal catalyst material (224) operatively associated with the process (216) catalyzes the formation of the multi-wall carbon nanotube (213).

Dillon, Anne C. (Boulder, CO); Mahan, Archie H. (Golden, CO); Alleman, Jeffrey L. (Lakewood, CO)

2010-10-26T23:59:59.000Z

247

Annual Report Diana H. Wall, Director  

E-Print Network [OSTI]

Student Sustainability Center more than doubled its student engagement, and our pre-college Summer2013-2014 Annual Report #12;Diana H. Wall, Director CSU is at the forefront of sustainability if such systems are to endure, and developing the expertise that is needed to shape a sustainable future

248

Domain wall partition functions and KP  

E-Print Network [OSTI]

We observe that the partition function of the six vertex model on a finite square lattice with domain wall boundary conditions is (a restriction of) a KP tau function and express it as an expectation value of charged free fermions (up to an overall normalization).

O Foda; M Wheeler; M Zuparic

2009-01-15T23:59:59.000Z

249

Design of wetted wall bioaerosol concentration cyclones  

E-Print Network [OSTI]

...................................................................................... 24 Aerosol-to-aerosol collection efficiency.................................................... 24 Wetting pattern on the impacting wall ? effect of an atomizer.................. 24..................................................................................... 67 Figure 3.4. Cold temperature experiemental setup ........................................................... 68 Figure 3.5. Preliminary heating system for the 1250 L/min cyclone and thermo-couple locations...

Seo, Youngjin

2009-05-15T23:59:59.000Z

250

THE CHINESE WALL LATTICE Ravi Sandhu  

E-Print Network [OSTI]

security policy for confidentiality · Mixture of free choice (discretionary) and mandatory of interest class #12;4 CHINESE WALL EXAMPLE BANKS OIL COMPANIESBANKS OIL COMPANIES A B X Y #12;5 READ ACCESS BREWER-NASH SIMPLE SECURITY S can read O only if · O is in the same company dataset as· O is in the same

Sandhu, Ravi

251

Reactor pressure vessel nozzle  

DOE Patents [OSTI]

A nozzle for joining a pool of water to a nuclear reactor pressure vessel includes a tubular body having a proximal end joinable to the pressure vessel and a distal end joinable in flow communication with the pool. The body includes a flow passage therethrough having in serial flow communication a first port at the distal end, a throat spaced axially from the first port, a conical channel extending axially from the throat, and a second port at the proximal end which is joinable in flow communication with the pressure vessel. The inner diameter of the flow passage decreases from the first port to the throat and then increases along the conical channel to the second port. In this way, the conical channel acts as a diverging channel or diffuser in the forward flow direction from the first port to the second port for recovering pressure due to the flow restriction provided by the throat. In the backflow direction from the second port to the first port, the conical channel is a converging channel and with the abrupt increase in flow area from the throat to the first port collectively increase resistance to flow therethrough. 2 figs.

Challberg, R.C.; Upton, H.A.

1994-10-04T23:59:59.000Z

252

On Two-Phase Relative Permeability and Capillary Pressure of Rough-Walled Rock Fractures  

E-Print Network [OSTI]

in Single Rock Joints", Licentiate Thesis, Lulea Universityof Technology, Lulea, Sweden. Heiba, A. A. , Sahimi, M. ,

Pruess ed, K.; Tsang, Y.W.

1989-01-01T23:59:59.000Z

253

Analysis of the pressure-wall interaction at the release of a stop closure  

E-Print Network [OSTI]

In producing a stop consonant, a soft tissue articulator, such as the lower lip, the tongue tip, or the tongue body, is raised to make an airtight closure. Stevens [I] pp 32 9-3 30 hypothesized that the interaction of the ...

Chen, Lan, S.M. Massachusetts Institute of Technology

2011-01-01T23:59:59.000Z

254

Vehicle Technologies Office Merit Review 2014: Heavy-Duty Low...  

Broader source: Energy.gov (indexed) [DOE]

Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty Combustion Modeling Vehicle Technologies Office Merit Review 2014: Heavy-Duty Low-Temperature and Diesel Combustion &...

255

Heavy Ion Fusion Science Virtual National Laboratory  

E-Print Network [OSTI]

to today's large NP accelerators like GSI-FAIR, RHIC economical for 1-2 GWe baseload power plants. Heavy chambers. · Competitive economics: projected in several power plant studies and with no high levelSlide 1 Heavy Ion Fusion Science Virtual National Laboratory Briefing for the National Academy

256

A Heavy Flavor Tracker for STAR  

SciTech Connect (OSTI)

We propose to construct a Heavy Flavor Tracker (HFT) for the STAR experiment at RHIC. The HFT will bring new physics capabilities to STAR and it will significantly enhance the physics capabilities of the STAR detector at central rapidities. The HFT will ensure that STAR will be able to take heavy flavor data at all luminosities attainable throughout the proposed RHIC II era.

Xu, Z.; Chen, Y.; Kleinfelder, S.; Koohi, A.; Li, S.; Huang, H.; Tai, A.; Kushpil, V.; Sumbera, M.; Colledani, C.; Dulinski, W.; Himmi,A.; Hu, C.; Shabetai, A.; Szelezniak, M.; Valin, I.; Winter, M.; Surrow,B.; Van Nieuwenhuizen, G.; Bieser, F.; Gareus, R.; Greiner, L.; Lesser,F.; Matis, H.S.; Oldenburg, M.; Ritter, H.G.; Pierpoint, L.; Retiere, F.; Rose, A.; Schweda, K.; Sichtermann, E.; Thomas, J.H.; Wieman, H.; Yamamoto, E.; Kotov, I.

2005-03-14T23:59:59.000Z

257

Heavy photon search experiment at JLAB  

SciTech Connect (OSTI)

The Heavy Photon Search (HPS) experiment in Hall-B at Jefferson Lab will search for new heavy vector boson(s), aka 'heavy photons', in the mass range of 20 MeV/c{sup 2} to 1000 MeV/c{sup 2} using the scattering of high energy, high intensity electron beams off a high Z target. The proposed measurements will cover the region of parameter space favored by the muon g-2 anomaly, and will explore a significant region of parameter space, not only at large couplings (??/? > 10{sup ?7}), but also in the regions of small couplings, down to ??/??10{sup ?10}. The excellent vertexing capability of the Si-tracker uniquely enables HPS to cover the small coupling region. Also, HPS will search for heavy photons in an alternative to the e{sup +}e{sup ?} decay mode, in the heavy photon's decay to ?{sup +}??.

Stepanyan, S. [Jefferson Lab, Newport News, VA (United States); Collaboration: HPS Collaboration

2013-11-07T23:59:59.000Z

258

QCD mechanisms for heavy particle production  

SciTech Connect (OSTI)

For very large pair mass, the production of heavy quarks and supersymmetric particles is expected to be governed by ACD fusion subprocesses. At lower mass scales other QCD mechanisms such as prebinding distortion and intrinsic heavy particle Fock states can become important, possibly accounting for the anomalies observed for charm hadroproduction. We emphasize the importance of final-state Coulomb interactions at low relative velocity in QCD and predict the existence of heavy narrow four quark resonances (c c-bar u u-bar) and (cc c-bar c-bar) in ..gamma gamma.. reactions. Coherent QCD contributions are discussed as a contribution to the non-additivity of nuclear structure functions and heavy particle production cross sections. We also predict a new type of amplitude zero for exclusive heavy meson pair production which follows from the tree-graph structure of QCD. 35 refs., 8 figs., 1 tab.

Brodsky, S.J.

1985-09-01T23:59:59.000Z

259

Climbing Wall Climbing Wall PoliciesURWC and St Paul Gym  

E-Print Network [OSTI]

a belay/lead qualification card visible on their harness and have passed the qualification test. Climbers may use personal climbing equipment (harness, belay device, etc.) at the wall. Old or worn equipment

Amin, S. Massoud

260

Standard guide for mutual inductance bridge applications for wall thickness determinations in boiler tubing  

E-Print Network [OSTI]

1.1 This guide describes a procedure for obtaining relative wall thickness indications in ferromagnetic and non-ferromagnetic steels using the mutual inductance bridge method. The procedure is intended for use with instruments capable of inducing two substantially identical magnetic fields and noting the change in inductance resulting from differing amounts of steel. It is used to distinguish acceptable wall thickness conditions from those which could place tubular vessels or piping at risk of bursting under high temperature and pressure conditions. 1.2 This guide is intended to satisfy two general needs for users of industrial Mutual Inductance Bridge (MIB) equipment: (1) the need for a tutorial guide addressing the general principles of Mutual Inductance Bridges as they apply to industrial piping; and (2) the need for a consistent set of MIB performance parameter definitions, including how these performance parameters relate to MIB system specifications. Potential users and buyers, as well as experienced M...

American Society for Testing and Materials. Philadelphia

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Engineering the fusion reactor first wall  

SciTech Connect (OSTI)

Recently the National Academy of Engineering published a set of Grand Challenges in Engineering in which the second item listed was entitled 'Provide energy from fusion'. Clearly a key component of this challenge is the science and technology associated with creating and maintaining burning plasmas. This is being vigorously addressed with both magnetic and inertial approaches with various experiments such as ITER and NIF. Considerably less attention is being given to another key component of this challenge, namely engineering the first wall that will contain the burning plasma. This is a daunting problem requiring technologies and materials that can not only survive, but also perform multiple essential functions in this extreme environment. These functions are (1) shield the remainder of the device from radiation. (2) convert of neutron energy to useful heat and (3) breed and extract tritium to maintain the reactor fuel supply. The first wall must not contaminate the plasma with impurities. It must be infused with cooling to maintain acceptable temperatures on plasma facing and structural components. It must not degrade. It must avoid excessive build-up of tritium on surfaces, and, if surface deposits do form, must be receptive to cleaning techniques. All these functions and constraints must be met while being subjected to nuclear and thermal radiation, particle bombardment, high magnetic fields, thermal cycling and occasional impingement of plasma on the surface. And, operating in a nuclear environment, the first wall must be fully maintainable by remotely-operated manipulators. Elements of the first wall challenge have been studied since the 1970' s both in the US and internationally. Considerable foundational work has been performed on plasma facing materials and breeding blanket/shield modules. Work has included neutronics, materials fabrication and joining, fluid flow, tritium breeding, tritium recovery and containment, energy conversion, materials damage and magnetohydrodynamics. While work to date has been quite valuable, no blanket concept has been built and operated in anything approaching a realistic fusion reactor environment. Rather, work has been limited to isolated experiments on first wall components and paper studies. The need now is to complete necessary R&D on first wall components, assemble components into a practical design, and test the first wall in a realistic fusion environment. Besides supporting work, major prototype experiments could be performed in non-nuclear experiments, as part of the ITER project and as part of the Component Test Facility. The latter is under active consideration and is a proposed machine which would use a driven plasma to expose an entire first wall to a fusion environment. Key US contributors to first wall research have been UCLA, UCSD, U of Wisconsin, LANL, ORNL, PNNL, Argonne and Idaho National Lab. Current efforts have been coordinated by UCLA. It is recognized that when this work progresses to a larger scale, leadership from a national laboratory will be required. LANL is well-prepared to provide such leadership.

Wurden, Glen [Los Alamos National Laboratory; Scott, Willms [Los Alamos National Laboratory

2008-01-01T23:59:59.000Z

262

Heavy quark physics from SLD  

SciTech Connect (OSTI)

This report covers preliminary measurements from SLD on heavy quark production at the Z{sup 0}, using 150,000 hadronic Z{sup 0} decays accumulated during the 1993-1995 runs. A measurement of R{sub b} with a lifetime double tag is presented. The high electron beam polarization of the SLC is employed in the direct measurement of the parity-violating parameters A{sub b} and A{sub c} by use of the left-right forward-backward asymmetry. The lifetimes of B{sup +} and B{sup 0} mesons have been measured by two analyses. The first identifies semileptonic decays of B mesons with high (p,p{sub t}) leptons; the second analysis isolates a sample of B meson decays with a two-dimensional impact parameter tag and reconstructs the decay length and charge using a topological vertex reconstruction method.

Messner, R. [Stanford Univ., CA (United States)

1997-01-01T23:59:59.000Z

263

Heavy Duty Vehicle Futures Analysis.  

SciTech Connect (OSTI)

This report describes work performed for an Early Career Research and Development project. This project developed a heavy-duty vehicle (HDV) sector model to assess the factors influencing alternative fuel and efficiency technology adoption. This model builds on a Sandia light duty vehicle sector model and provides a platform for assessing potential impacts of technological advancements developed at the Combustion Research Facility. Alternative fuel and technology adoption modeling is typically developed around a small set of scenarios. This HDV sector model segments the HDV sector and parameterizes input values, such as fuel prices, efficiencies, and vehicle costs. This parameterization enables sensitivity and trade space analyses to identify the inputs that are most associated with outputs of interest, such as diesel consumption and greenhouse gas emissions. Thus this analysis tool enables identification of the most significant HDV sector drivers that can be used to support energy security and climate change goals.

Askin, Amanda Christine; Barter, Garrett; West, Todd H.; Manley, Dawn Kataoka

2014-05-01T23:59:59.000Z

264

Study of flow fields induced by surface dielectric barrier discharge actuator in low-pressure air  

SciTech Connect (OSTI)

Surface dielectric barrier discharge (SDBD) is a promising method for a flow control. Flow fields induced by a SDBD actuator driven by the ac voltage in static air at low pressures varying from 1.0 to 27.7?kPa are measured by the particle image velocimetry method. The influence of the applied ac voltage frequency and magnitude on the induced flow fields is studied. The results show that three different classes of flow fields (wall jet flow field, complex flow field, and vortex-shape flow field) can be induced by the SDBD actuator in the low-pressure air. Among them, the wall jet flow field is the same as the tangential jet at atmospheric pressure, which is, together with the vertical jet, the complex flow field. The vortex-shape flow field is composed of one vertical jet which points towards the wall and two opposite tangential jets. The complex and the vortex-shape flow fields can be transformed to the wall jet flow field when the applied ac voltage frequency and magnitude are changed. It is found that the discharge power consumption increases initially, decreases, and then increases again at the same applied ac voltage magnitude when the air pressure decreases. The tangential velocity of the wall jet flow field increases when the air pressure decreases. It is however opposite for the complex flow field. The variation of the applied ac voltage frequency influences differently three different flow fields. When the applied ac voltage magnitude increases at the same applied ac voltage frequency, the maximal jet velocity increases, while the power efficiency increases only initially and then decreases again. The discharge power shows either linear or exponential dependences on the applied ac voltage magnitude.

Che, Xueke, E-mail: chedk@163.com, E-mail: st@mail.iee.ac.cn; Nie, Wansheng; Tian, Xihui; Hou, Zhiyong; He, Haobo; Zhou, Penghui; Zhou, Siyin; Yang, Chao [Equipment Academy, Beijing 101416 (China)] [Equipment Academy, Beijing 101416 (China); Shao, Tao, E-mail: chedk@163.com, E-mail: st@mail.iee.ac.cn [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China)] [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China)

2014-04-15T23:59:59.000Z

265

SCR Systems for Heavy Duty Trucks: Progress Towards Meeting Euro...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Systems for Heavy Duty Trucks: Progress Towards Meeting Euro 4 Emission Standards in 2005 SCR Systems for Heavy Duty Trucks: Progress Towards Meeting Euro 4 Emission Standards in...

266

Integrated Virtual Lab in Supporting Heavy Duty Engine and Vehicle...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Virtual Lab in Supporting Heavy Duty Engine and Vehicle Emission Rulemaking Integrated Virtual Lab in Supporting Heavy Duty Engine and Vehicle Emission Rulemaking Presentation...

267

Off-Highway Heavy Vehicle Diesel Efficiency Improvement and Emissions...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Off-Highway Heavy Vehicle Diesel Efficiency Improvement and Emissions Reduction Off-Highway Heavy Vehicle Diesel Efficiency Improvement and Emissions Reduction 2005 Diesel Engine...

268

Comparing Emissions Benefits from Regulating Heavy Vehicle Idling...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Emissions Benefits from Regulating Heavy Vehicle Idling Comparing Emissions Benefits from Regulating Heavy Vehicle Idling 2005 Diesel Engine Emissions Reduction (DEER) Conference...

269

Design of Integrated Laboratory and Heavy-Duty Emissions Testing...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

of Integrated Laboratory and Heavy-Duty Emissions Testing Center Design of Integrated Laboratory and Heavy-Duty Emissions Testing Center Both simulated and actual diesel emissions...

270

WORKSHOP REPORT: Trucks and Heavy-Duty Vehicles Technical Requirements...  

Energy Savers [EERE]

Heavy-Duty Vehicles Technical Requirements and Gaps for Lightweight and Propulsion Materials WORKSHOP REPORT: Trucks and Heavy-Duty Vehicles Technical Requirements and Gaps for...

271

Advanced Natural Gas Engine Technology for Heavy Duty Vehicles  

Broader source: Energy.gov (indexed) [DOE]

ALTERNATIVE. EVERY Advanced Natural Gas Engine Advanced Natural Gas Engine Technology for Heavy Duty Vehicles Technology for Heavy Duty Vehicles Dr. Mostafa M Kamel Dr. Mostafa M...

272

Long Plasma Source for Heavy Ion Beam Charge Neutralization  

E-Print Network [OSTI]

neutralizing plasma column the heavy ion beam can focus to aPlasmas are a source of unbound electrons for charge neutralizing intense heavy ion beams to focus

Efthimion, P.C.

2009-01-01T23:59:59.000Z

273

California Policy Stimulates Carbon Negative CNG for Heavy Duty...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

California Policy Stimulates Carbon Negative CNG for Heavy Duty Trucks California Policy Stimulates Carbon Negative CNG for Heavy Duty Trucks Describes system for fueling truck...

274

Vehicle Technologies Office Merit Review 2014: Advanced Heavy...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Advanced Heavy-Duty Engine Systems and Emissions Control Modeling and Analysis Vehicle Technologies Office Merit Review 2014: Advanced Heavy-Duty Engine Systems and Emissions...

275

Ultrasensitive Voltammetric Detection of Trace Heavy Metal Ions...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Voltammetric Detection of Trace Heavy Metal Ions Using Carbon Nanotube Nanoelectrode Array. Ultrasensitive Voltammetric Detection of Trace Heavy Metal Ions Using Carbon Nanotube...

276

NOx Adsorbers for Heavy Duty Truck Engines - Testing and Simulation...  

Broader source: Energy.gov (indexed) [DOE]

NOx Adsorbers for Heavy Duty Truck Engines - Testing and Simulation NOx Adsorbers for Heavy Duty Truck Engines - Testing and Simulation This report provides the results of an...

277

Fuel Efficiency and Emissions Optimization of Heavy-Duty Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

and Emissions Optimization of Heavy-Duty Diesel Engines using Model-Based Transient Calibration Fuel Efficiency and Emissions Optimization of Heavy-Duty Diesel Engines using...

278

Molecular dynamics simulations of ion range profiles for heavy...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

simulations of ion range profiles for heavy ions in light targets. Molecular dynamics simulations of ion range profiles for heavy ions in light targets. Abstract: The determination...

279

TBU-0061- In the Matter of Misti Wall  

Broader source: Energy.gov [DOE]

Misti Wall (the complainant or Wall), appeals the dismissal of her complaint of retaliation filed under 10 C.F.R. Part 708, the Department of Energy (DOE) Contractor Employee Protection Program. As...

280

After Exodus : re-occupation of the metropolitan wall  

E-Print Network [OSTI]

The title "Exodus alludes to a restricted exclave encircled by a forbidding wall -- effect, a prison on the scale of a metropolis, and one in which people sought refuge voluntarily. Over the past forty years, similar walls ...

Allison, Jordan Lloyd Norman

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Modeling Left Ventricle Wall Motion Using Tagged Magnetic Resonance Imaging  

E-Print Network [OSTI]

A two-parameter computational model is proposed for the study of the regional motion of the left ventricle (LV) wall using tagged magnetic resonance imaging (tMRI) data. In this model, the LV wall motion is mathematically ...

Alenezy, Mohammed D.

2009-04-17T23:59:59.000Z

282

Electrical signature of magnetic domain-wall dynamics  

E-Print Network [OSTI]

Current-induced domain-wall dynamics is studied in a thin ferromagnetic nanowire. The domain-wall dynamics is described by simple equations with four parameters. We propose a procedure to unambiguously determine these parameters by all...

Liu, Y.; Tretiakov, O. A.; Abanov, Artem.

2011-01-01T23:59:59.000Z

283

High pressure furnace  

DOE Patents [OSTI]

A high temperature high pressure furnace has a hybrid partially externally heated construction. A metallic vessel fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum)). The disclosed alloy is fabricated into 11/4 or 2 inch, 32 mm or 50 mm bar stock and has a length of about 22 inches, 56 cm. This bar stock has an aperture formed therein to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the vessel is provided with a small blind aperture into which a thermocouple can be inserted. The closed end of the vessel is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior. 19 figures.

Morris, D.E.

1993-09-14T23:59:59.000Z

284

High pressure oxygen furnace  

DOE Patents [OSTI]

A high temperature high pressure oxygen furnace having a hybrid partially externally heated construction is disclosed. A metallic bar fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 inch bar stock and has a length of about 17 inches. This bar stock is gun drilled for over 16 inches of its length with 0.400 inch aperture to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the bar is provided with a small support aperture into which both a support and a thermocouple can be inserted. The closed end of the gun drilled bar is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior.

Morris, Donald E. (Kensington, CA)

1992-01-01T23:59:59.000Z

285

High pressure oxygen furnace  

DOE Patents [OSTI]

A high temperature high pressure oxygen furnace having a hybrid partially externally heated construction is disclosed. A metallic bar fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized, the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 inch bar stock and has a length of about 17 inches. This bar stock is gun drilled for over 16 inches of its length with 0.400 inch aperture to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the bar is provided with a small support aperture into which both a support and a thermocouple can be inserted. The closed end of the gun drilled bar is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior. 5 figs.

Morris, D.E.

1992-07-14T23:59:59.000Z

286

Continuous pressure letdown system  

DOE Patents [OSTI]

A continuous pressure letdown system connected to a hopper decreases a pressure of a 2-phase (gas and solid) dusty gas stream flowing through the system. The system includes a discharge line for receiving the dusty gas from the hopper, a valve, a cascade nozzle assembly positioned downstream of the discharge line, a purge ring, an inert gas supply connected to the purge ring, an inert gas throttle, and a filter. The valve connects the hopper to the discharge line and controls introduction of the dusty gas stream into the discharge line. The purge ring is connected between the discharge line and the cascade nozzle assembly. The inert gas throttle controls a flow rate of an inert gas into the cascade nozzle assembly. The filter is connected downstream of the cascade nozzle assembly.

Sprouse, Kenneth M.; Matthews, David R.; Langowski, Terry

2010-06-08T23:59:59.000Z

287

Pressure suppression system  

DOE Patents [OSTI]

A pressure suppression system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and an enclosed gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel. The GDCS pool includes a plenum for receiving through an inlet the non-condensable gas carried with steam from the drywell following a loss-of-coolant accident (LOCA). A condenser is disposed in the GDCS plenum for condensing the steam channeled therein and to trap the non-condensable gas therein. A method of operation includes draining the GDCS pool following the LOCA and channeling steam released into the drywell following the LOCA into the GDCS plenum for cooling along with the non-condensable gas carried therewith for trapping the gas therein.

Gluntz, Douglas M. (San Jose, CA)

1994-01-01T23:59:59.000Z

288

Pressure suppression system  

DOE Patents [OSTI]

A pressure suppression system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and an enclosed gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel. The GDCS pool includes a plenum for receiving through an inlet the non-condensable gas carried with steam from the drywell following a loss-of-coolant accident (LOCA). A condenser is disposed in the GDCS plenum for condensing the steam channeled therein and to trap the non-condensable gas therein. A method of operation includes draining the GDCS pool following the LOCA and channeling steam released into the drywell following the LOCA into the GDCS plenum for cooling along with the non-condensable gas carried therewith for trapping the gas therein. 3 figs.

Gluntz, D.M.

1994-10-04T23:59:59.000Z

289

Pressure activated diaphragm bonder  

DOE Patents [OSTI]

A device is available for bonding one component to another, particularly for bonding electronic components of integrated circuits, such as chips, to a substrate. The bonder device in one embodiment includes a bottom metal block having a machined opening wherein a substrate is located, a template having machined openings which match solder patterns on the substrate, a thin diaphragm placed over the template after the chips have been positioned in the openings therein, and a top metal block positioned over the diaphragm and secured to the bottom block, with the diaphragm retained therebetween. The top block includes a countersink portion which extends over at least the area of the template and an opening through which a high pressure inert gas is supplied to exert uniform pressure distribution over the diaphragm to keep the chips in place during soldering. A heating means is provided to melt the solder patterns on the substrate and thereby solder the chips thereto. 4 figs.

Evans, L.B.; Malba, V.

1997-05-27T23:59:59.000Z

290

High pressure furnace  

DOE Patents [OSTI]

A high temperature high pressure furnace has a hybrid partially externally heated construction. A metallic vessel fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 or 2 inch, 32 mm or 50 mm bar stock and has a length of about 22 inches, 56 cm. This bar stock has an aperture formed therein to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the vessel is provided with a small blind aperture into which a thermocouple can be inserted. The closed end of the vessel is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior.

Morris, Donald E. (Kensington, CA)

1993-01-01T23:59:59.000Z

291

Hydroconversion of heavy oils. [Residue of tar sand bitumen distillation  

SciTech Connect (OSTI)

A method is described for hydroconversion of feedstocks consisting essentially of at least one heavy hydrocarbon oil selected from the group consisting of residue of petroleum oil distillation and the residue of tar sand bitumen distillation to enhance the recovery of 350/sup 0/-650/sup 0/F boiling product fraction. The method comprises treating such feed stock with hydrogen at superatmospheric pressure and in the presence of finely divided active hydrogenation catalyst in consecutive reaction stages. An initial reaction stage is carried out at a temperature in the range of 780/sup 0/-825/sup 0/F, and a subsequent reaction stage is directly carried out after the initial reaction stage at a higher temperature in the range of 800/sup 0/F-860/sup 0/F, the temperature of the subsequent reaction stage being at least 20/sup 0/F higher than that of the initial reaction stage.

Garg, D.

1986-08-19T23:59:59.000Z

292

Isotropization from Color Field Condensate in heavy ion collisions  

E-Print Network [OSTI]

The expanding fireball shortly after a heavy ion collision may be qualitatively described by a condensate of color fields or gluons which is analogous to Bose-Einstein-condensation for massive bosonic particles. This condensate is a transient non-equilibrium phenomenon and breaks Lorentz-boost symmetry. The dynamics of color field condensates involves collective excitations and is rather different from the perturbative scattering of gluons. In particular, it provides for an efficient mechanism to render the local pressure approximately isotropic after a short time of 0.2 fm/c. We suggest that an isotropic color field condensate may play a central role for a simple description of prethermalization and isotropization in the early stages of the collision.

Stefan Floerchinger; Christof Wetterich

2014-08-27T23:59:59.000Z

293

High pressure storage vessel  

DOE Patents [OSTI]

Disclosed herein is a composite pressure vessel with a liner having a polar boss and a blind boss a shell is formed around the liner via one or more filament wrappings continuously disposed around at least a substantial portion of the liner assembly combined the liner and filament wrapping have a support profile. To reduce susceptible to rupture a locally disposed filament fiber is added.

Liu, Qiang

2013-08-27T23:59:59.000Z

294

DEVELOPMENT PRACTICES FOR OPTIMIZED MEOR IN SHALLOW HEAVY OIL RESERVOIRS  

SciTech Connect (OSTI)

The objective of this research project is to demonstrate an economically viable and sustainable method of producing shallow heavy oil reserves in western Missouri and southeastern Kansas, using an integrated approach including surface geochemical surveys, conventional MEOR treatments, horizontal fracturing in vertical wells, electrical resistivity tomography (ERT), and reservoir simulation to optimize the recovery process. The objective also includes transferring the knowledge gained from the project to other local landowners, to demonstrate how they may identify and develop their own heavy oil resources with minimal capital investment. In the twelve to eighteen-month project period, three wells were equipped with ERT arrays. Electrical resistivity tomography (ERT) background measurements were taken in the three ERT equipped wells. Pumping equipment was installed on the two fracture stimulated wells and pumping tests were conducted following the hydraulic fracture treatments. All wells were treated monthly with microbes, by adding a commercially available microbial mixture to wellbore fluids. ERT surveys were taken on a monthly basis, following microbial treatments. Worked performed to date demonstrates that resistivity changes are occurring in the subsurface, with resistivity increasing slightly. Pumping results for the hydraulically fractured wells were disappointing, with only a show of oil recovered and an increase in well shut-in pressure.

Shari Dunn-Norman

2005-06-01T23:59:59.000Z

295

High Performance Walls in Hot-Dry Climates  

SciTech Connect (OSTI)

High performance walls represent a high priority measure for moving the next generation of new homes to the Zero Net Energy performance level. The primary goal in improving wall thermal performance revolves around increasing the wall framing from 2x4 to 2x6, adding more cavity and exterior rigid insulation, achieving insulation installation criteria meeting ENERGY STAR's thermal bypass checklist, and reducing the amount of wood penetrating the wall cavity.

Hoeschele, M.; Springer, D.; Dakin, B.; German, A.

2015-01-01T23:59:59.000Z

296

UF{sub 6} pressure excursions during cylinder heating  

SciTech Connect (OSTI)

As liquid UF{sub 6} inside a cylinder changes from a liquid to a solid, it forms a porous solid which occupies approximately the same volume as that of the liquid before cooling. Simultaneously as the liquid cools, UF{sub 6} vapor in the cylinder ullage above the liquid desublimes on the upper region of the inner cylinder wall. This solid is a dense, glass-like material which can accumulate to a significant thickness. The thickness of the solid coating on the upper cylinder wall and directly behind the cylinder valve area will vary depending on the conditions during the cooling stage. The amount of time lapsed between UF{sub 6} solidification and UF{sub 6} liquefaction can also affect the UF{sub 6} coating. This is due to the daily ambient heat cycle causing the coating to sublime from the cylinder wall to cooler areas, thus decreasing the thickness. Structural weakening of the dense UF{sub 6} layer also occurs due to cylinder transport vibration and thermal expansion. During cylinder heating, the UF{sub 6} nearest the cylinder wall will liquefy first. As the solid coating behind the cylinder valve begins to liquefy, it results in increased pressure depending upon the available volume for expansion. At the Paducah Gaseous Diffusion Plant (PGDP) during the liquefaction of the UF{sub 6} in cylinders in the UF{sub 6} feed and sampling autoclaves, this pressure increase has resulted in the activation of the systems rupture discs which are rated at 100 pounds per square inch differential.

Brown, P.G. [Martin Marietta Energy Systems, Inc., Paducah, KY (United States)

1991-12-31T23:59:59.000Z

297

Heavy Water Components Test Reactor Decommissioning - Major Component Removal  

SciTech Connect (OSTI)

The Heavy Water Components Test Reactor (HWCTR) facility (Figure 1) was built in 1961, operated from 1962 to 1964, and is located in the northwest quadrant of the Savannah River Site (SRS) approximately three miles from the site boundary. The HWCTR facility is on high, well-drained ground, about 30 meters above the water table. The HWCTR was a pressurized heavy water test reactor used to develop candidate fuel designs for heavy water power reactors. It was not a defense-related facility like the materials production reactors at SRS. The reactor was moderated with heavy water and was rated at 50 megawatts thermal power. In December of 1964, operations were terminated and the facility was placed in a standby condition as a result of the decision by the U.S. Atomic Energy Commission to redirect research and development work on heavy water power reactors to reactors cooled with organic materials. For about one year, site personnel maintained the facility in a standby status, and then retired the reactor in place. In 1965, fuel assemblies were removed, systems that contained heavy water were drained, fluid piping systems were drained, deenergized and disconnected and the spent fuel basin was drained and dried. The doors of the reactor facility were shut and it wasn't until 10 years later that decommissioning plans were considered and ultimately postponed due to budget constraints. In the early 1990s, DOE began planning to decommission HWCTR again. Yet, in the face of new budget constraints, DOE deferred dismantlement and placed HWCTR in an extended surveillance and maintenance mode. The doors of the reactor facility were welded shut to protect workers and discourage intruders. The $1.6 billion allocation from the American Recovery and Reinvestment Act to SRS for site clean up at SRS has opened the doors to the HWCTR again - this time for final decommissioning. During the lifetime of HWCTR, 36 different fuel assemblies were tested in the facility. Ten of these experienced cladding failures as operational capabilities of the different designs were being established. In addition, numerous spills of heavy water occurred within the facility. Currently, radiation and radioactive contamination levels are low within HWCTR with most of the radioactivity contained within the reactor vessel. There are no known insults to the environment, however with the increasing deterioration of the facility, the possibility exists that contamination could spread outside the facility if it is not decommissioned. An interior panoramic view of the ground floor elevation taken in August 2009 is shown in Figure 2. The foreground shows the transfer coffin followed by the reactor vessel and control rod drive platform in the center. Behind the reactor vessel is the fuel pool. Above the ground level are the polar crane and the emergency deluge tank at the top of the dome. Note the considerable rust and degradation of the components and the interior of the containment building. Alternative studies have concluded that the most environmentally safe, cost effective option for final decommissioning is to remove the reactor vessel, steam generators, and all equipment above grade including the dome. Characterization studies along with transport models have concluded that the remaining below grade equipment that is left in place including the transfer coffin will not contribute any significant contamination to the environment in the future. The below grade space will be grouted in place. A concrete cover will be placed over the remaining footprint and the groundwater will be monitored for an indefinite period to ensure compliance with environmental regulations. The schedule for completion of decommissioning is late FY2011. This paper describes the concepts planned in order to remove the major components including the dome, the reactor vessel (RV), the two steam generators (SG), and relocating the transfer coffin (TC).

Austin, W.; Brinkley, D.

2010-05-05T23:59:59.000Z

298

CFD Validation of Gas Injection in Flowing Mercury over Vertical Smooth and Grooved Wall  

SciTech Connect (OSTI)

The Spallation Neutron Source (SNS) is an accelerator-based neutron source at Oak Ridge National Laboratory (ORNL).The nuclear spallation reaction occurs when a proton beam hits liquid mercury. This interaction causes thermal expansion of the liquid mercury which produces high pressure waves. When these pressure waves hit the target vessel wall, cavitation can occur and erode the wall. Research and development efforts at SNS include creation of a vertical protective gas layer between the flowing liquid mercury and target vessel wall to mitigate the cavitation damage erosion and extend the life time of the target. Since mercury is opaque, computational fluid dynamics (CFD) can be used as a diagnostic tool to see inside the liquid mercury and guide the experimental efforts. In this study, CFD simulations of three dimensional, unsteady, turbulent, two-phase flow of helium gas injection in flowing liquid mercury over smooth, vertically grooved and horizontally grooved walls are carried out with the commercially available CFD code Fluent-12 from ANSYS. The Volume of Fluid (VOF) model is used to track the helium-mercury interface. V-shaped vertical and horizontal grooves with 0.5 mm pitch and about 0.7 mm depth were machined in the transparent wall of acrylic test sections. Flow visualization data of helium gas coverage through transparent test sections is obtained with a high-speed camera at the ORNL target test facility (TTF). The helium gas mass flow rate is 8 mg/min and introduced through a 0.5 mm diameter port. The local mercury velocity is 0.9 m/s. In this paper, the helium gas flow rate and the local mercury velocity are kept constant for the three cases. Time integration of predicted helium gas volume fraction over time is done to evaluate the gas coverage and calculate the average thickness of the helium gas layer. The predicted time-integrated gas coverage over vertically grooved and horizontally grooved test sections is better than over a smooth wall. The simulations show that the helium gas is trapped inside the grooves. The predicted time-averaged gas coverage is in good qualitative agreement with the measured gas coverage.

Abdou, Ashraf A [ORNL; Wendel, Mark W [ORNL; Felde, David K [ORNL; Riemer, Bernie [ORNL

2009-01-01T23:59:59.000Z

299

Enhanced dielectric-wall linear accelerator  

DOE Patents [OSTI]

A dielectric-wall linear accelerator is enhanced by a high-voltage, fast e-time switch that includes a pair of electrodes between which are laminated alternating layers of isolated conductors and insulators. A high voltage is placed between the electrodes sufficient to stress the voltage breakdown of the insulator on command. A light trigger, such as a laser, is focused along at least one line along the edge surface of the laminated alternating layers of isolated conductors and insulators extending between the electrodes. The laser is energized to initiate a surface breakdown by a fluence of photons, thus causing the electrical switch to close very promptly. Such insulators and lasers are incorporated in a dielectric wall linear accelerator with Blumlein modules, and phasing is controlled by adjusting the length of fiber optic cables that carry the laser light to the insulator surface. 6 figs.

Sampayan, S.E.; Caporaso, G.J.; Kirbie, H.C.

1998-09-22T23:59:59.000Z

300

Gravitational infall in the hard wall model  

E-Print Network [OSTI]

An infalling shell in the hard wall model provides a simple holographic model for energy injection in a confining gauge theory. Depending on its parameters, a scalar shell either collapses into a large black brane, or scatters between the hard wall and the anti-de Sitter boundary. In the scattering regime, we find numerical solutions that keep oscillating for as long as we have followed their evolution, and we provide an analytic argument that shows that a black brane can never be formed. This provides examples of states in infinite-volume field theory that never thermalize. We find that the field theory expectation value of a scalar operator keeps oscillating, with an amplitude that undergoes modulation.

B. Craps; E. J. Lindgren; A. Taliotis; J. Vanhoof; H. Zhang

2014-12-15T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Proposal on Lithium Wall Experiment (LWX) on PBXM 1  

E-Print Network [OSTI]

Proposal on Lithium Wall Experiment (LWX) on PBX­M 1 Leonid E. Zakharov, Princeton University; OUTLINE 1. Mini­conference on Lithium walls and low recycling regime. 2. PBX­M Capabilities. 3. Motivation "Lithium covered walls and low recycling regimes in toka­ maks". APS meeting, October 23­27, 2000, Quebec

Zakharov, Leonid E.

302

Manipulation and Imaging of Individual Single-Walled Carbon Nanotubes  

E-Print Network [OSTI]

Manipulation and Imaging of Individual Single-Walled Carbon Nanotubes with an Atomic Force Microscope** By Henk W. C. Postma, Allard Sellmeijer, and Cees Dekker* Carbon nanotubes[1] have attracted-walled nanotubes,[3±5] the prototype single-walled tubes are much more difficult to study since their diameter

303

Building Cathedrals and Breaking down Reinforced Concrete Walls  

E-Print Network [OSTI]

Building Cathedrals and Breaking down Reinforced Concrete Walls Michel Brou´e Institut Henri distinction between great mathematicians Concrete walls breakers Michel Brou´e (Institut Henri Poincar´e) John Concrete walls breakers Cathedrals builders Michel Brou´e (Institut Henri Poincar´e) John Thompson

Broué, Michel - Institut de Mathématiques de Jussieu, Université Paris 7

304

Designing Precast Concrete Cross Wall Joints Against Progressive Collapse  

E-Print Network [OSTI]

Designing Precast Concrete Cross Wall Joints Against Progressive Collapse Researcher: Mohamad concrete cross wall constructions. Ronan Point Collapse (http://en.wikipedia.org/wiki/Ronan_Point) #12;Due gap is listed as follows: · Limited number of studies for designing precast concrete cross wall

Birmingham, University of

305

Brick Walls and AdS/CFT  

E-Print Network [OSTI]

We discuss the relationship between the bulk-boundary correspondence in Rehren's algebraic holography (and in other 'fixed-background' approaches to holography) and in mainstream 'Maldacena AdS/CFT'. Especially, we contrast the understanding of black-hole entropy from the viewpoint of QFT in curved spacetime -- in the framework of 't Hooft's 'brick wall' model -- with the understanding based on Maldacena AdS/CFT. We show that the brick-wall modification of a Klein Gordon field in the Hartle-Hawking-Israel state on 1+2-Schwarzschild AdS (BTZ) has a well-defined boundary limit with the same temperature and entropy as the brick-wall-modified bulk theory. One of our main purposes is to point out a close connection, for general AdS/CFT situations, between the puzzle raised by Arnsdorf and Smolin regarding the relationship between Rehren's algebraic holography and mainstream AdS/CFT and the puzzle embodied in the 'correspondence principle' proposed by Mukohyama and Israel in their work on the brick-wall approach to black hole entropy. Working on the assumption that similar results will hold for bulk QFT other than the Klein Gordon field and for Schwarzschild AdS in other dimensions, and recalling the first author's proposed resolution to the Mukohyama-Israel puzzle based on his 'matter-gravity entanglement hypothesis', we argue that, in Maldacena AdS/CFT, the algebra of the boundary CFT is isomorphic only to a proper subalgebra of the bulk algebra, albeit (at non-zero temperature) the (GNS) Hilbert spaces of bulk and boundary theories are still the 'same' -- the total bulk state being pure, while the boundary state is mixed (thermal). We also argue from the finiteness of its boundary (and hence, on our assumptions, also bulk) entropy at finite temperature, that the Rehren dual of the Maldacena boundary CFT cannot itself be a QFT and must, instead, presumably be something like a string theory.

Bernard S. Kay; L. Ortiz

2014-05-22T23:59:59.000Z

306

Hollow clay tile wall program summary report  

SciTech Connect (OSTI)

Many of the Y-12 Plant buildings, constructed during the 1940s and 1950s, consist of steel ed concrete framing infilled with hollow clay tile (HCT). The infill was intended to provide for building enclosure and was not designed to have vertical or lateral load-carrying capacity. During the late 1970s and early 1980s, seismic and wind evaluations were performed on many of these buildings in conjunction with the preparation of a site-wide safety analysis report. This analytical work, based on the best available methodology, considered lateral load-carrying capacity of the HCT infill on the basis of building code allowable shear values. In parallel with the analysis effort, DOE initiated a program to develop natural phenomena capacity and performance criteria for existing buildings, but these criteria did not specify guidelines for determining the lateral force capacity of frames infilled with HCT. The evaluation of infills was, therefore, based on the provisions for the design of unreinforced masonry as outlined in standard masonry codes. When the results of the seismic and wind evaluations were compared with the new criteria, the projected building capacities fell short of the requirements. Apparently, if the buildings were to meet the new criteria, many millions of dollars would be required for building upgrades. Because the upgrade costs were significant, the assumptions and approaches used in the analyses were reevaluated. Four issues were identified: (1) Once the infilled walls cracked, what capacity (nonlinear response), if any, would the walls have to resist earthquake or wind loads applied in the plane of the infill (in-plane)? (2) Would the infilled walls remain within the steel or reinforced concrete framing when subjected to earthquake or high wind loads applied perpendicular to the infill (out-of-plane)? (3) What was the actual shear capacity of the HCT infill? (4) Was modeling the HCT infill as a shear wall the best approach?

Henderson, R.C.; Jones, W.D. [Gilbert/Commonwealth, Inc., Oak Ridge, TN (United States); Beavers, J.E. [MS Technology, Inc. (United States)

1995-07-30T23:59:59.000Z

307

Conserved currents for Mobius Domain Wall Fermions  

E-Print Network [OSTI]

We derive the exactly conserved vector, and almost conserved axial currents for rational approximations to the overlap operator with a general Mobius kernel. The approach maintains manifest Hermiticity, and allows matrix elements of the currents to be constructed at no extra cost after solution of the usual 5d system of equations, similar to the original approach of Furman and Shamir for domain wall Fermions.

P. A. Boyle

2014-11-20T23:59:59.000Z

308

1993 NEC 1) (Single-Walled Carbon  

E-Print Network [OSTI]

MWNT (Vapor-grown carbon fiber, VGCF)33) 10001300 34) SWNT CCVD Smalley 15) CO SWNT SWNT 1993 NEC 1) (Single-Walled Carbon Nanotubes, SWNTs) 1(a) 1nm µm µm SWNTs 2) (MWNTs) 1(c 29,30,35-41) SWNT , MgO Fe/Co, Ni/Co, Mo/Co nm SWNT VGCF Fe(CO)5 SWNT Ethanol tank Hot

Maruyama, Shigeo

309

Optimization of Pressurized Oxy4Combustion with Flameless Reactor  

SciTech Connect (OSTI)

Pressurized OxyECombustion is one of the most promising technologies for utilityEscale power generation plants. Benefits include the ability to burn low rank coal and capture C02. By increasing the flue gas pressure during this process, greater efficiencies are derived from increased quantity and quality of thermal energy recovery. UPA with modeling support from MIT and testing and data verification by Georgia Tech’s Research Center designed and built a 100kW system capable of demonstrating pressurized oxyEcombustion using a flameless combustor. Wyoming PRB coal was run at 15 and 32 bar. Additional tests were not completed but sampled data demonstrated the viability of the technology over a broader range of operating pressures, Modeling results illustrated a flat efficiency curve over 20 bar, with optimum efficiency achieved at 29 bar. This resulted in a 33% (HHV) efficiency, a 5 points increase in efficiency versus atmospheric oxyEcombustion, and a competitive cost of electricity plus greater C02 avoidance costs then prior study’s presented. UPA’s operation of the benchEscale system provided evidence that key performance targets were achieved: flue gas sampled at the combustor outlet had nonE detectable residual fly ashes, and low levels of SO3 and heavyEmetal. These results correspond to prior pressurized oxyEcombustion testing completed by IteaEEnel.

Malavasi, Massimo; Landegger, Gregory

2014-06-30T23:59:59.000Z

310

Phenomenology of Wall Bounded Newtonian Turbulence  

E-Print Network [OSTI]

We construct a simple analytic model for wall-bounded turbulence, containing only four adjustable parameters. Two of these parameters characterize the viscous dissipation of the components of the Reynolds stress-tensor and other two parameters characterize their nonlinear relaxation. The model offers an analytic description of the profiles of the mean velocity and the correlation functions of velocity fluctuations in the entire boundary region, from the viscous sub-layer, through the buffer layer and further into the log-layer. As a first approximation, we employ the traditional return-to-isotropy hypothesis, which yields a very simple distribution of the turbulent kinetic energy between the velocity components in the log-layer: the streamwise component contains a half of the total energy whereas the wall-normal and the cross-stream components contain a quarter each. In addition, the model predicts a very simple relation between the von-K\\'arm\\'an slope $\\kappa $ and the turbulent velocity in the log-law region $v^+$ (in wall units): $v^+=6 \\kappa$. These predictions are in excellent agreement with DNS data and with recent laboratory experiments.

Victor S. L'vov; Anna Pomyalov; Itamar Procaccia; Sergej S. Zilitinkevich

2005-06-28T23:59:59.000Z

311

ADVANCED HIGH PERFORMANCE SOLID WALL BLANKET CONCEPTS  

SciTech Connect (OSTI)

OAK A271 ADVANCED HIGH PERFORMANCE SOLID WALL BLANKET CONCEPTS. First wall and blanket (FW/blanket) design is a crucial element in the performance and acceptance of a fusion power plant. High temperature structural and breeding materials are needed for high thermal performance. A suitable combination of structural design with the selected materials is necessary for D-T fuel sufficiency. Whenever possible, low afterheat, low chemical reactivity and low activation materials are desired to achieve passive safety and minimize the amount of high-level waste. Of course the selected fusion FW/blanket design will have to match the operational scenarios of high performance plasma. The key characteristics of eight advanced high performance FW/blanket concepts are presented in this paper. Design configurations, performance characteristics, unique advantages and issues are summarized. All reviewed designs can satisfy most of the necessary design goals. For further development, in concert with the advancement in plasma control and scrape off layer physics, additional emphasis will be needed in the areas of first wall coating material selection, design of plasma stabilization coils, consideration of reactor startup and transient events. To validate the projected performance of the advanced FW/blanket concepts the critical element is the need for 14 MeV neutron irradiation facilities for the generation of necessary engineering design data and the prediction of FW/blanket components lifetime and availability.

WONG, CPC; MALANG, S; NISHIO, S; RAFFRAY, R; SAGARA, S

2002-04-01T23:59:59.000Z

312

Differential pressure pin discharge apparatus  

DOE Patents [OSTI]

Disclosed is a discharge assembly for allowing elongate pins to be discharged from an area of relatively low pressure to an area of relatively greater pressure. The discharge assembly includes a duck valve having a lip piece made of flexible material. The flexible lip piece responds to a fluctuating pressure created downstream by an aspirator. The aspirator reduces the downstream pressure sensed by the duck valve when the discharge assembly is in the open position. This allows elongate pins to be moved through the duck valve with no backflow because the aspirator pressure is less than the pressure in the low pressure area from which the pins originate. Closure of the assembly causes the aspirator static pressure to force the flexible duck valve lip piece into a tightly sealed position also preventing backflow. The discharge assembly can be easily controlled using a single control valve which blocks the flow of aspirator gas and closes the pin passageway extending through the assembly.

Oakley, David J. (Richland, WA)

1987-01-01T23:59:59.000Z

313

Economics of Steam Pressure Reduction  

E-Print Network [OSTI]

Economics of Steam Pressure Reduction is a technical paper that addresses the operating and economic advantages associated with the program to lower the steam operating pressure. Evaluation of a testing program will be discussed. The paper...

Sylva, D. M.

314

Heat transfer and friction in a square channel with one-wall or two-wall rib turbulators  

E-Print Network [OSTI]

walls 83 66 Ribbed side Nusselt number ratio versus friction factor ratio for broken ribs on one wall 84 67 Smooth side Nusselt number ratio versus friction factor ratio for broken ribs on one wall . , 68 Ribbed side Nusselt number ratio versus... on one wall . 95 96 97 INTRODUCTION Early heat transfer study shows that roughening the surface is an effective way to enhance the heat transfer from a surface. Modern turbine design applies turbulence promoters/ribs inside cooling passages...

Huang, Jie Joy

1991-01-01T23:59:59.000Z

315

Pressure Data Within BOP- ODS  

Broader source: Energy.gov [DOE]

This file describes the components within the BOP and the pressure readings taken during diagnostic operations on May 25.

316

Pressure Data Within BOP- XLS  

Broader source: Energy.gov [DOE]

This file describes the components within the BOP and the pressure readings taken during diagnostic operations on May 25.

317

Field test of two high-pressure, direct-contact downhole steam generators. Volume I. Air/diesel system  

SciTech Connect (OSTI)

As a part of the Project DEEP STEAM to develop technology to more efficiently utilize steam for the recovery of heavy oil from deep reservoirs, a field test of a downhole steam generator (DSG) was performed. The DSG burned No. 2 diesel fuel in air and was a direct-contact, high pressure device which mixed the steam with the combustion products and injected the resulting mixture directly into the oil reservoir. The objectives of the test program included demonstration of long-term operation of a DSG, development of operational methods, assessment of the effects of the steam/combustion gases on the reservoir and comparison of this air/diesel DSG with an adjacent oxygen/diesel direct contact generator. Downhole operation of the air/diesel DSG was started in June 1981 and was terminated in late February 1982. During this period two units were placed downhole with the first operating for about 20 days. It was removed, the support systems were slightly modified, and the second one was operated for 106 days. During this latter interval the generator operated for 70% of the time with surface air compressor problems the primary source of the down time. Thermal contact, as evidenced by a temperature increase in the production well casing gases, and an oil production increase were measured in one of the four wells in the air/diesel pattern. Reservoir scrubbing of carbon monoxide was observed, but no conclusive data on scrubbing of SO/sub x/ and NO/sub x/ were obtained. Corrosion of the DSG combustor walls and some other parts of the downhole package were noted. Metallurgical studies have been completed and recommendations made for other materials that are expected to better withstand the downhole combustion environment. 39 figures, 8 tables.

Marshall, B.W.

1983-05-01T23:59:59.000Z

318

A Study of the Filling of Wall Cavities With Retrofit Wall Insulation.  

SciTech Connect (OSTI)

The Pacific Northwest Power Marketing Agency, the Bonneville Power Administration (BPA), conducted a retrofit wall insulation study to determine the effects of various obstructions within a wall cavity, where voids are likely to occur, and preferred filling methods and material types. The insulation test structure was composed of four 8-foot /times/ 12-foot walls, and was built using standard construction practices. The inside walls were clear plastic glazing, instead of gypsum board, to enable viewing of the filling process. A total of eight tests were performed: four cellulose, two rockwool, and two fiberglass. One- and two-hole filling methods were observed. All insulations were found to perform in the same basic manner with all experiencing the same problem areas. Common installer problems were empty spaces at the tops of cavities and missed cavities, especially above headers. Wiring and lath and plaster consistently caused reduced insulation densities in cavities. The problems with wiring, lath and plaster, and other features in the wall cavities were avoided with the use of a filler tube. The filler tube also provided a more consistent fill along the length of the entire cavity. 2 figs., 3 tabs.

Flores, Joseph A.; Grill, Alan R.

1988-08-01T23:59:59.000Z

319

Control of magnetohydrodynamic modes with a resistive wall above the wall stabilization limit  

SciTech Connect (OSTI)

Studies are shown of control of magnetohydrodynamic (MHD) modes in the presence of a resistive wall, below and above the regime for which stabilization is possible with a perfectly conducting wall, i.e., in and above the ideal wall limit. The results show that resistive plasma (tearing-like) modes can be feedback stabilized for current profiles which are unstable above the ideal wall limit, both for tokamak-like and reversed field pinch (RFP)-like profiles. However, above the limit for wall stabilization of ideal plasma modes, resonant or nonresonant, the feedback scheme cannot provide stabilization. The control scheme senses both normal and tangential components of the perturbed magnetic field, and the feedback is proportional to a linear combination of the two. Neither plasma rotation nor complex gain is included. A cylindrical reduced MHD model, in resistive or ideal form, is used, with tokamak-like profiles [increasing profile of q(r)] or RFP-like profiles [decreasing q(r)]. The possible relevance to RFPs and tokamaks is discussed.

Finn, John M. [T-15, Plasma Theory, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

2006-08-15T23:59:59.000Z

320

Resumming the pressure  

E-Print Network [OSTI]

The convergence properties of the resummed thermal perturbation series for the thermodynamic pressure are investigated by comparison with the exact results obtained in large-N phi^4 theory and possibilities for improvements are discussed. By going beyond conventional resummed perturbation theory, renormalization has to be carried out nonperturbatively yet consistently. This is exemplified in large-N phi^4_4 and in a special large-N \\phi^3_6 model that mimics QED in the limit of large flavour number.

Anton Rebhan

1998-09-21T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Method of non-destructively inspecting a curved wall portion  

DOE Patents [OSTI]

A method of non-destructively inspecting a curved wall portion of a large and thick walled vessel for a defect by computed tomography is provided. A collimated source of radiation is placed adjacent one side of the wall portion and an array of detectors for the radiation is placed on the other side adjacent the source. The radiation from the source passing through the wall portion is then detected with the detectors over a limited angle, dependent upon the curvature of the wall of the vessel, to obtain a dataset. The source and array are then coordinately moved relative to the wall portion in steps and a further dataset is obtained at each step. The plurality of datasets obtained over the limited angle is then processed to produce a tomogram of the wall portion to determine the presence of a defect therein. In a preferred embodiment, the curved wall portion has a center of curvature so that the source and the array are positioned at each step along a respective arc curved about the center. If desired, the detector array and source can be reoriented relative to a new wall portion and an inspection of the new wall portion can be easily obtained. Further, the source and detector array can be indexed in a direction perpendicular to a plane including the limited angle in a plurality of steps so that by repeating the detecting and moving steps at each index step, a three dimensional image can be created of the wall portion.

Fong, James T. (Bethel Park, PA)

1996-01-01T23:59:59.000Z

322

Heavy Metal Tolerance Robert S. Boyd, Nishanta Rajakaruna  

E-Print Network [OSTI]

be useful to solve environmental problems caused by heavy metal pollution. General Overviews General: a recent example targeting cellular mechanisms affected by heavy metals is Bánfalvi 2011. Pollution by heavy metals is an important environmental problem, and sources that focus on heavy metal pollution

Rajakaruna, Nishanta

323

Detection of Heavy Metal Ions Based on Quantum Point Contacts  

E-Print Network [OSTI]

. The ability to detect trace amounts of metal ions is important because of the toxicity of heavy metal ionsDetection of Heavy Metal Ions Based on Quantum Point Contacts Vasanth Rajagopalan, Salah Boussaad on many living organisms and the consequence of heavy metal ions not being biodegradable. To date, heavy

Zhang, Yanchao

324

Heavy Oil Upgrading from Electron Beam (E-Beam) Irradiation  

E-Print Network [OSTI]

-heavy oil, and oil shale. Tremendous amounts of heavy oil resources are available in the world. Fig. 1.1 shows the total world oil reserves, and indicates that heavy oil, extra heavy oil, and bitumen make up about 70% of the world?s total oil resources...

Yang, Daegil

2011-02-22T23:59:59.000Z

325

HEAVY-ION IMAGING APPLIED TO MEDICINE  

E-Print Network [OSTI]

heavy particles rat h er than the vax~at1.on 1n t h e x-rayprograms on the a PDPll-34 and VAX- 780 computers. The image

Fabrikant, J.I.

2013-01-01T23:59:59.000Z

326

Partonic coalescence in relativistic heavy ion collisions  

E-Print Network [OSTI]

Using a covariant coalescence model, we study hadron production in relativistic heavy ion collisions from both soft partons in the quark-gluon plasma and hard partons in minijets. Including transverse flow of soft partons and independent...

Greco, V.; Ko, Che Ming; Levai, P.

2003-01-01T23:59:59.000Z

327

Heavy Mobile Equipment Mechanic (One Mechanic Shop)  

Broader source: Energy.gov [DOE]

The position is a Heavy Mobile Equipment Mechanic (One Mechanic Shop) located in Kent, Washington, and will be responsible for the safe and efficient operation of a field garage performing...

328

Heavy-Ion Fusion Accelerator Research, 1991  

SciTech Connect (OSTI)

This report discusses the following topics: research with multiple- beam experiment MBE-4; induction linac systems experiments; and long- range research and development of heavy-ion fusion accelerators.

Not Available

1992-03-01T23:59:59.000Z

329

Heavy metals in Antarctic organisms  

SciTech Connect (OSTI)

To evaluate levels of essential (zinc and copper) and non-essential (mercury and cadmium) heavy metals, 34 species of organisms from different areas close to the Antarctic Peninsula were analysed. These included algae, filter-feeders, omnivorous invertebrates and vertebrates. Mercury was not detected, while cadmium was found in the majority of organisms analysed (detection limit was 0.05 ppm for both metals). The highest cadmium concentration was observed in the starfish Odontaster validus. Anthozoans, sipunculids and nudibranchs showed maximum levels of zinc, while the highest copper level was found in the gastropod Trophon brevispira. Mercury and cadmium levels in fishes were below the detection limit. Concentrations of essential and non-essential metals in birds were highest in liver followed by muscle and eggs. Cadmium and mercury levels in muscle of southern elephant seals were above the detection limit, whereas in Antarctic fur seals they were below it. The objective of the study was to gather baseline information for metals in Antarctic Ocean biota that may be needed to detect, measure and monitor future environmental changes. 46 refs., 7 figs., 8 tabs.

Moreno, J.E.A. de; Moreno, V.J. [Universidad Nacional de Mar del Plata (Argentina); Gerpe, M.S.; Vodopivez, C. [Instituto Antartico Argentino, Buenos Aires (Argentina)

1997-02-01T23:59:59.000Z

330

Ideal Magnetohydrodynamics Stability Spectrum with a Resistive Wall  

SciTech Connect (OSTI)

We show that the eigenvalue equations describing a cylindrical ideal magnetophydrodynamicsw (MHD) plasma interacting with a thin resistive wall can be put into the standard mathematical form: ??? = ??? ?. This is accomplished by using a finite element basis for the plasma, and by adding an extra degree of freedom corresponding to the electrical current in the thin wall. The standard form allows the use of linear eigenvalue solvers, without additional interations, to compute the complete spectrum of plasma modes in the presence of a surrounding restrictive wall at arbitrary separation. We show that our method recovers standard results in the limits of (1) an infinitely resistive wall (no wall), and (2) a zero resistance wall (ideal wall).

S.P. Smith and S.C. Jardin

2008-05-22T23:59:59.000Z

331

High-pressure neutron diffraction  

SciTech Connect (OSTI)

This lecture will cover progress and prospect of applications of high-pressure neutron diffraction techniques to Earth and materials sciences. I will first introduce general high-pressure research topics and available in-situ high-pressure techniques. Then I'll talk about high-pressure neutron diffraction techniques using two types of pressure cells: fluid-driven and anvil-type cells. Lastly, I will give several case studies using these techniques, particularly, those on hydrogen-bearing materials and magnetic transitions.

Xu, Hongwu [Los Alamos National Laboratory

2011-01-10T23:59:59.000Z

332

Probing the Symmetry Energy with Heavy Ions  

E-Print Network [OSTI]

Constraints on the EoS for symmetric matter (equal neutron and proton numbers) at supra-saturation densities have been extracted from energetic collisions of heavy ions. Collisions of neutron-deficient and neutron-rich heavy ions now provide initial constraints on the EoS of neutron-rich matter at sub-saturation densities. Comparisons are made to other available constraints.

Lynch, W G; Zhang, Y; Danielewicz, P; Famiano, M; Li, Z; Steiner, A W

2009-01-01T23:59:59.000Z

333

Probing the Symmetry Energy with Heavy Ions  

E-Print Network [OSTI]

Constraints on the EoS for symmetric matter (equal neutron and proton numbers) at supra-saturation densities have been extracted from energetic collisions of heavy ions. Collisions of neutron-deficient and neutron-rich heavy ions now provide initial constraints on the EoS of neutron-rich matter at sub-saturation densities. Comparisons are made to other available constraints.

W. G. Lynch; M. B. Tsang; Y. Zhang; P. Danielewicz; M. Famiano; Z. Li; A. W. Steiner

2009-01-05T23:59:59.000Z

334

Combustor oscillation pressure stabilizer  

SciTech Connect (OSTI)

In accordance with the objective of the present invention, the active control of unsteady combustion induced oscillations in a combustion chamber fired by a suitable fuel and oxidizer mixture, such as a hydrocarbon fuel and air mixture, is provided by restructuring and moving the position of the main flame front and thereby increasing the transport time and displacing the pressure wave further away from the in-phase relationship with the periodic heat release. The restructuring and repositioning of the main flame are achieved by utilizing a pilot flame which is pulsed at a predetermined frequency corresponding to less than about one-half the frequency of the combustion oscillation frequency with the duration of each pulse being sufficient to produce adequate secondary thermal energy to restructure the main flame and thereby decouple the heat release from the acoustic coupling so as to lead to a reduction in the dynamic pressure amplitude. The pulsating pilot flame produces a relatively small and intermittently existing flame front in the combustion zone that is separate from the oscillating main flame front but which provides the thermal energy necessary to effectively reposition the location of the oscillating main flame front out of the region in the combustion zone where the acoustic coupling can occur with the main flame and thereby effectively altering the oscillation-causing phase relationship with the heat of combustion.

Gemmen, R.S.; Richards, G.A.; Yip, M.T.J.; Robey, E.; Cully, S.R.; Addis, R.E.

1996-12-31T23:59:59.000Z

335

SUPRI heavy oil research program. Annual report, October 1, 1991--September 30, 1992  

SciTech Connect (OSTI)

The goal of the Stanford University Petroleum Research Institute is to conduct research directed toward increasing the recovery of heavy oils. Presently, SUPRI is working in five main directions: (1) flow properties studies to assess the influence of different reservoir conditions (temperature and pressure) on the absolute and relative permeability to oil and water and on capillary pressure; (2) in-situ combustion to evaluate the effect of different reservoir parameters on the in-situ combustion process and to study the kinetics of the reactions; (3) steam with additives to develop and understand the mechanisms of the process using commercially available surfactants for reduction of gravity override and channeling of steam; (4) formation evaluation to develop and improve techniques of formation evaluation such as tracer tests and pressure transient tests; and field support services to provide technical support for design and monitoring of DOE sponsored or industry initiated field projects.

Brigham, W.E.; Ramey, H.J. Jr.; Castanier, L.M.

1993-08-01T23:59:59.000Z

336

SUPRI Heavy Oil Research Program Twenty-First Annual Report, SUPRI TR-111  

SciTech Connect (OSTI)

The goal of the Stanford University Petroleum Research Institute is to conduct research directed toward increasing the recovery of heavy oils. Present, SUPRI is working in five main directions: (1) Flow Properties Studies - To assess the influence of different reservoir conditions (temperature and pressure) on the absolute and relative permeability to oil and water and on capillary pressure; (2) In-Situ Combustion - To evaluate the effect of different reservoir parameters on the in-situ combustion process. This project includes the study of the kinetics of the reactions; (3) Steam with Additives- To develop and understand the mechanisms of the process using commercially available surfactants for reduction of gravity override and channeling of steam; (4) Formation Evaluation - To develop and improve techniques of formation evaluation such as tracer tests and pressure transient tests; and (5) Field Support Services - To provide technical support for design and monitoring of DOE sponsored or industry initiated field projects.

Brigham, William E.; Castanier, Louis; Kovscek, Anthony R.

1999-08-09T23:59:59.000Z

337

SUPRI heavy oil research program. Annual report, February 8, 1995--February 7, 1996  

SciTech Connect (OSTI)

The goal of the Stanford University Petroleum Research Institute (SUPRI) is to conduct research directed toward increasing the recovery of heavy oils. Presently SUPRI is working in five main directions: (1) flow properties studies to assess the influence of different reservoir conditions (temperature and pressure) on the absolute and relative permeability to oil and water and on capillary pressure; (2) in-situ combustion to evaluate the effect of different reservoir parameters on the in-situ combustion process; (3) steam with additives to develop and understand the mechanisms of the process using commercially available surfactants for reduction of gravity override and channeling of steam; (4) formation evaluation to develop and improve techniques of formation evaluation such as tracer tests and pressure transient tests; and (5) field support services to provide technical support for design and monitoring of DOE sponsored or industry initiated field projects. This report consists of abstracts of reports and copies of technical papers presented or published.

Brigham, W.E.; Castanier, L.M.

1996-06-01T23:59:59.000Z

338

A lower cost development path for heavy ion fusion  

SciTech Connect (OSTI)

If two features of the inertial fusion process are exploited successfully, they can lead to significantly lower costs for demonstrating the feasibility of commercial electric power production from this source of energy. First, fusion capsule ignition and burn physics is independent of reaction chamber size and hydrodynamically-equivalent capsules can be designed to perform at small yield, exactly as they do at large yield. This means that an integrated test of all power plant components and feasibility tests of various reaction chamber concepts can be done at much smaller sizes (about 1--2 m first wall radius) and much lower powers (tens of MWs) than magnetic fusion development facilities such as ITER. Second, the driver, which is the most expensive component of currently conceived IFE development facilities, can be used to support more than one experiment target chamber/reactor (simultaneously and/or sequentially). These two factors lead to lower development facility costs, modular facilities, and the planning flexibility to spread costs over time or do several things in parallel and thus shorten the total time needed for development of Inertial Fusion Energy (IFE). In this paper the authors describe the general feature of a heavy ion fusion development plan that takes advantage of upgradable accelerators and the ability to test chambers and reactor systems at small scale in order to reduce development time and costs.

Hogan, W.J. [Lawrence Livermore National Lab., CA (United States); Meier, W.R. [Shafer (W.J.) Associates, Inc., Wakefield, MA (United States)

1993-05-19T23:59:59.000Z

339

Definition of heavy oil and natural bitumen  

SciTech Connect (OSTI)

Definition and categorization of heavy oils and natural bitumens are generally based on physical or chemical attributes or on methods of extraction. Ultimately, the hydrocarbon's chemical composition will govern both its physical state and the extraction technique applicable. These oils and bitumens closely resemble the residuum from wholecrude distillation to about 1,000/degree/F; if the residuum constitutes at least 15% of the crude, it is considered to be heavy. In this material is concentrated most of the trace elements, such as sulfur, oxygen, and nitrogen, and metals, such as nickel and vanadium. A widely used definition separates heavy oil from natural bitumen by viscosity, crude oil being less, and bitumen more viscous than 10,000 cp. Heavy crude then falls in the range 10/degree/-20/degree/ API inclusive and extra-heavy oil less than 10/degree/ API. Most natural bitumen is natural asphalt (tar sands, oil sands) and has been defined as rock containing hydrocarbons more viscous than 10,000 cp or else hydrocarbons that may be extracted from mined or quarried rock. Other natural bitumens are solids, such as gilsonite, grahamite, and ozokerite, which are distinguished by streak, fusibility, and solubility. The upper limit for heavy oil may also be set at 18/degree/ API, the approximate limit for recovery by waterflood.

Meyer, R.F.

1988-08-01T23:59:59.000Z

340

Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty...  

Broader source: Energy.gov (indexed) [DOE]

effects on LTC (SNL) Develop wall temperature diagnostic for studying liquid film dynamics (UW+SNL) Improve computer modeling for LTCdiesel sprays and study piston geometry...

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Wall, Pennsylvania: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to:Seadov PtyInformationSEDS data JumpWakulla County,Wall, Pennsylvania: Energy Resources

342

Gas turbine bucket wall thickness control  

DOE Patents [OSTI]

A core for use in casting a turbine bucket including serpentine cooling passages is divided into two pieces including a leading edge core section and a trailing edge core section. Wall thicknesses at the leading edge and the trailing edge of the turbine bucket can be controlled independent of each other by separately positioning the leading edge core section and the trailing edge core section in the casting die. The controlled leading and trailing edge thicknesses can thus be optimized for efficient cooling, resulting in more efficient turbine operation.

Stathopoulos, Dimitrios (Glenmont, NY); Xu, Liming (Greenville, SC); Lewis, Doyle C. (Greer, SC)

2002-01-01T23:59:59.000Z

343

Wall System Innovations: Familiar Materials, Better Performance |  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage »of| Department of EnergyDepartmentDepartment of Energy Wall System

344

Theoretical collapse pressures for two pressurized torispherical heads  

SciTech Connect (OSTI)

In order to determine the pressures at which real torispherical heads fail upon a single application of pressure, two heads were pressurized in recent Praxair tests, and displacements and strains were recorded at various locations. In this paper, theoretical results for the two test heads are presented in the form of curves of pressure versus crown deflections, using the available geometry and material parameters. From these curves, limit and collapse pressures are calculated, using procedures permitted by the ASME B and PV Code Section 8/Div.2. These pressures are shown to vary widely, depending on the method and model used to calculate them. The effect of no stress relief on the behavior of the Praxair test heads is also evaluated and found to be of no significance for neither the objectives of the tests nor the objectives of this paper. The results of this paper are submitted as an enhancement to the experimental results recorded during the Praxair tests.

Kalnins, A.; Updike, D.P. [Lehigh Univ., Bethlehem, PA (United States); Rana, M.D. [Praxair, Inc., Tonawanda, NY (United States). Research and Development Dept.

1995-12-01T23:59:59.000Z

345

Advanced Aerodynamic Devices to Improve the Performance, Economics, Handling, and Safety of Heavy Vehicles  

SciTech Connect (OSTI)

Research is being conducted at the Georgia Tech Research Institute (GTRI) to develop advanced aerodynamic devices to improve the performance, economics, stability, handling and safety of operation of Heavy Vehicles by using previously-developed and flight-tested pneumatic (blown) aircraft technology. Recent wind-tunnel investigations of a generic Heavy Vehicle model with blowing slots on both the leading and trailing edges of the trailer have been conducted under contract to the DOE Office of Heavy Vehicle Technologies. These experimental results show overall aerodynamic drag reductions on the Pneumatic Heavy Vehicle of 50% using only 1 psig blowing pressure in the plenums, and over 80% drag reductions if additional blowing air were available. Additionally, an increase in drag force for braking was confirmed by blowing different slots. Lift coefficient was increased for rolling resistance reduction by blowing only the top slot, while downforce was produced for traction increase by blowing only the bottom. Also, side force and yawing moment were generated on either side of the vehicle, and directional stability was restored by blowing the appropriate side slot. These experimental results and the predicted full-scale payoffs are presented in this paper, as is a discussion of additional applications to conventional commercial autos, buses, motor homes, and Sport Utility Vehicles.

Robert J. Englar

2001-05-14T23:59:59.000Z

346

Performance of reduced wall EPR insulated medium voltage power cables. Pat 1: Electrical characteristics  

SciTech Connect (OSTI)

Paper insulated lead covered cables (PILC) have had a long and successful heritage. After almost 100 years, this design of cable is still in operation and continues to be manufactured. However, utilities are now looking for a reliable replacement for PILC cables. This is due to two primary reasons: (1) difficulty in installing and maintaining this type of cable and (2) increasing pressure to replace these cables due to environmental concerns. To date diameter limitations of conventional extruded dielectric cables has impeded their replacement in existing PILC conduits. This paper describes a study for the evaluation for reliably reducing the insulation thickness to achieve a lower diameter cable to effectively replace PILC cable in existing conduits. Part 1 of the investigation reviews the theory of insulation wall determination and the test program carried out to evaluate electrical performance of reduced wall EPR cables. Additionally, cable design concepts and constructions are discussed. In Part 2 the mechanical performance on conventional and reduced wall EPR insulated cables are evaluated. This is reported in a separate paper.

Cinquemani, P.L.; Wen, Y.; Kuchta, F.L.; Doench, C. [Pirelli Cable Corp., Lexington, SC (United States)] [Pirelli Cable Corp., Lexington, SC (United States)

1997-04-01T23:59:59.000Z

347

Cradle and pressure grippers  

DOE Patents [OSTI]

A gripper that is designed to incorporate the functions of gripping, supporting and pressure tongs into one device. The gripper has two opposing finger sections with interlocking fingers that incline and taper to form a wedge. The interlocking fingers are vertically off-set so that the opposing finger sections may close together allowing the inclined, tapered tips of the fingers to extend beyond the plane defined by the opposing finger section's engagement surface. The range of motion defined by the interlocking relationship of the finger sections allows the gripper to grab, lift and support objects of varying size and shape. The gripper has one stationary and one moveable finger section. Power is provided to the moveable finger section by an actuating device enabling the gripper to close around an object to be lifted. A lifting bail is attached to the gripper and is supported by a crane that provides vertical lift.

Muniak, John E. (New York, NY)

2001-01-01T23:59:59.000Z

348

Flame-wall interaction simulation in a turbulent channel flow  

SciTech Connect (OSTI)

The interaction between turbulent premixed flames and channel walls is studied. Combustion is represented by a simple irreversible reaction with a large activation temperature. A low heat release assumption is used, but feedback to the flowfield can be allowed through viscosity changes. The effect of wall distance on local and global flame structure is investigated. Quenching distances and maximum wall heat fluxed computed in laminar cases are compared to DNS results. It is found that quenching distances decrease and maximum heat fluxes increase relative to laminar flame values, scaling with the turbulent strain rate. It is shown that these effects are due to large coherent structures which push flame elements towards the wall. The effect of wall strain in flame-wall interaction is studied in a stagnation line flow; this is used to explain the DNS results. The effects of the flame on the flow through viscosity changes is studied. It is also shown that remarkable flame events are produced by flame interaction with a horseshoe vortex: burned gases are pushed towards the wall at high speed and induce quenching and high wall heat flux while fresh gases are expelled from the wall region and form finger-like structures. Effects of the wall on flame surface density are investigated.

Bruneaux, G.; Akselvoll, K.; Poinsot, T.; Ferziger, J.H.

1996-10-01T23:59:59.000Z

349

Dynamic load test of Arquin-designed CMU wall.  

SciTech Connect (OSTI)

The Arquin Corporation has developed a new method of constructing CMU (concrete masonry unit) walls. This new method uses polymer spacers connected to steel wires that serve as reinforcing as well as a means of accurately placing the spacers so that the concrete block can be dry stacked. The hollows of the concrete block are then filled with grout. As part of a New Mexico Small Business Assistance Program (NMSBA), Sandia National Laboratories conducted a series of tests that dynamically loaded wall segments to compare the performance of walls constructed using the Arquin method to a more traditional method of constructing CMU walls. A total of four walls were built, two with traditional methods and two with the Arquin method. Two of the walls, one traditional and one Arquin, had every third cell filled with grout. The remaining two walls, one traditional and one Arquin, had every cell filled with grout. The walls were dynamically loaded with explosive forces. No significant difference was noted between the performance of the walls constructed by the Arquin method when compared to the walls constructed by the traditional method.

Jensen, Richard Pearson

2010-02-01T23:59:59.000Z

350

Thermal performance of steel-framed walls. Final report  

SciTech Connect (OSTI)

In wall construction, highly conductive members spaced along the wall, which allow higher heat transfer than that through less conductive areas, are referred to as thermal bridges. Thermal bridges in walls tend to increase heat loss and, under certain adverse conditions, can cause dust streaking (``ghosting``) on interior walls over studs due to temperature differentials, as well as condensation in and on walls. Although such adverse conditions can be easily avoided by proper thermal design of wall systems, these effects have not been well understood and thermal data has been lacking. Therefore, the present study was initiated to provide (1) a better understanding of the thermal behavior of steel-framed walls, (2) a set of R-values for typical wall constructions, and (3) information that could be used to develop improved methods of predicting R-values. An improved method for estimating R-value would allow an equitable comparison of thermal performance with other construction types and materials. This would increase the number of alternative materials for walls available to designers, thus allowing them to choose the optimum choice for construction. Twenty-three wall samples were tested in a calibrated hot box (ASTM C9761) to measure the thermal performance of steel-framed wall systems. The tests included an array of stud frame configurations, exterior sheathing and fiberglass batt insulations. Other studies have not included the use of insulating sheathing, which reduces the extent of the thermal bridges and improves total thermal performance. The purpose of the project was to provide measured R-values for commonly used steel-framed wall configurations and to improve R-value estimating methods. Test results were compared to R-value estimates using the parallel path method, the isothermal planes method and the ASHRAE Zone method. The comparison showed that the known procedures do not fully account for the three-dimensional effects created by steel framing in a wall.

Barbour, E. [NAHB Research Center, Inc., Upper Marlboro, MD (United States); Goodrow, J. [Holometrix, Inc., Bedford, MA (United States); Kosny, J.; Christian, J.E. [Oak Ridge National Lab., TN (United States)

1994-11-21T23:59:59.000Z

351

Heavy Truck Duty Cycle (HTDC) Project The Heavy Truck Duty Cycle (HTDC)  

E-Print Network [OSTI]

data from trucks operating in long-haul operations. The research program was designed to be conductedHeavy Truck Duty Cycle (HTDC) Project OVERVIEW The Heavy Truck Duty Cycle (HTDC) Project. The project involves efforts to collect, analyze and archive data and information related to class -8 truck

352

Intense Magnetized Plasma-Wall Interaction  

SciTech Connect (OSTI)

This research project studied wall-plasma interactions relevant to fusion science. Such interactions are a critical aspect of Magneto-Inertial Fusion (MIF) because flux compression by a pusher material, in particular the metal for the liner approach to MIF, involves strong eddy current heating on the surface of the pusher, and probably interactions and mixing of the pusher with the interior fuel during the time when fusion fuel is being burned. When the pusher material is a metal liner, high-energy-density conditions result in fascinating behavior. For example, "warm dense matter" is produced, for which material properties such as resistivity and opacity are not well known. In this project, the transformation into plasma of metal walls subjected to pulsed megagauss magnetic fields was studied with an experiment driven by the UNR 1 MA Zebra generator. The experiment was numerically simulated with using the MHRDR code. This simple, fundamental high-energy-density physics experiment, in a regime appropriate to MIF, has stimulated an important and fascinating comparison of numerical modeling codes and tables with experiment. In addition, we participated in developing the FRCHX experiment to compress a field-reversed-configuration (FRC) plasma with a liner, in collaboration with researchers from Air Force Research Laboratory and Los Alamos National Lab, and we helped develop diagnostics for the Plasma Liner Experiment (PLX) at LANL. Last, but not least, this project served to train students in high-energy-density physics.

Bauer, Bruno S. [UNR] [UNR; Fuelling, Stephan [UNR] [UNR

2013-11-30T23:59:59.000Z

353

Steam Oxidation at High Pressure  

SciTech Connect (OSTI)

A first high pressure test was completed: 293 hr at 267 bar and 670{degrees}C; A parallel 1 bar test was done for comparison; Mass gains were higher for all alloys at 267 bar than at 1 bar; Longer term exposures, over a range of temperatures and pressures, are planned to provide information as to the commercial implications of pressure effects; The planned tests are at a higher combination of temperatures and pressures than in the existing literature. A comparison was made with longer-term literature data: The short term exposures are largely consistent with the longer-term corrosion literature; Ferritic steels--no consistent pressure effect; Austenitic steels--fine grain alloys less able to maintain protective chromia scale as pressure increases; Ni-base alloys--more mass gains above 105 bar than below. Not based on many data points.

Holcomb, Gordon R. [NETL; Carney, Casey [URS

2013-07-19T23:59:59.000Z

354

Heavy flavours in heavy-ion collisions: quenching, flow and correlations  

E-Print Network [OSTI]

We present results for the quenching, elliptic flow and azimuthal correlations of heavy flavour particles in high-energy nucleus-nucleus collisions obtained through the POWLANG transport setup, developed in the past to study the propagation of heavy quarks in the Quark-Gluon Plasma and here extended to include a modeling of their hadronization in the presence of a medium. Hadronization is described as occurring via the fragmentation of strings with endpoints given by the heavy (anti-)quark Q(Qbar) and a thermal parton qbar(q) from the medium. The flow of the light quarks is shown to affect significantly the R_AA and v_2 of the final D mesons, leading to a better agreement with the experimental data. The approach allows also predictions for the angular correlation between heavy-flavour hadrons (or their decay electrons) and the charged particles produced in the fragmentation of the heavy-quark strings.

A. Beraudo; A. De Pace; M. Monteno; M. Nardi; F. Prino

2014-12-17T23:59:59.000Z

355

High Pressure Hydrogen Materials Compatibility of Piezoelectric...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Pressure Hydrogen Materials Compatibility of Piezoelectric Films. High Pressure Hydrogen Materials Compatibility of Piezoelectric Films. Abstract: Abstract: Hydrogen is being...

356

To estimate vapor pressure easily  

SciTech Connect (OSTI)

Vapor pressures as functions of temperature for approximately 700 major organic chemical compounds are given. The tabulation also gives the temperature range for which the data are applicable. Minimum and maximum temperatures are denoted by TMIN and TMAX. The Antoine equation that correlates vapor pressure as a function of temperature is described. A representative comparison of calculated and actual data values for vapor pressure is shown for ethyl alcohol. The coefficient tabulation is based on both literature (experimental data) and estimated values.

Yaws, C.L.; Yang, H.C. (Lamar Univ., Beaumont, TX (USA))

1989-10-01T23:59:59.000Z

357

Hollow porous-wall glass microspheres for hydrogen storage  

DOE Patents [OSTI]

A porous wall hollow glass microsphere is provided having a diameter range of between 1 to 200 microns, a density of between 1.0 to 2.0 gm/cc, a porous-wall structure having wall openings defining an average pore size of between 10 to 1000 angstroms, and which contains therein a hydrogen storage material. The porous-wall structure facilitates the introduction of a hydrogen storage material into the interior of the porous wall hollow glass microsphere. In this manner, the resulting hollow glass microsphere can provide a membrane for the selective transport of hydrogen through the porous walls of the microsphere, the small pore size preventing gaseous or liquid contaminants from entering the interior of the hollow glass microsphere.

Heung, Leung K. (Aiken, SC); Schumacher, Ray F. (Aiken, SC); Wicks, George G. (Aiken, SC)

2010-02-23T23:59:59.000Z

358

Density hysteresis of heavy water confined in a nanoporous silica matrix  

SciTech Connect (OSTI)

A neutron scattering technique was developed to measure the density of heavy water confined in a nanoporous silica matrix in a temperature-pressure range, from 300 to 130 K and from 1 to 2,900 bars, where bulk water will crystalize. We observed a prominent hysteresis phenomenon in the measured density profiles between warming and cooling scans above 1,000 bars. We inter- pret this hysteresis phenomenon as support (although not a proof) of the hypothetical existence of a first-order liquid liquid phase transition of water that would exist in the macroscopic system if crystallization could be avoided in the relevant phase region. Moreover, the density data we obtained for the confined heavy water under these conditions are valuable to large communities in biology and earth and planetary sciences interested in phenomena in which nanometer-sized water layers are involved.

Zhang, Yang [ORNL; Faraone, Antonio [National Institute of Standards and Technology (NIST); Kamitakahara, William [ORNL; Liu, Kao-Hsiang [National Taiwan University; Mou, Chung-Yuan [National Taiwan University; Leao, Juscelino B [ORNL; Chang, Sung C [ORNL; Chen, Sow-hsin H [ORNL

2011-01-01T23:59:59.000Z

359

Heavy-section steel technology and irradiation programs-retrospective and prospective views  

SciTech Connect (OSTI)

In 1965, the Atomic Energy Commission (AEC), at the advice of the Advisory Committee on Reactor Safeguards (ACRS), initiated the process that resulted in the establishment of the Heavy Section Steel Technology (HSST) Program at Oak Ridge National Laboratory (ORNL). In 1989, the Heavy-Section Steel Irradiation (HSSI) Program, formerly the HSST task on irradiation effects, was formed as a separate program, and, in 2007, the HSST/HSSI Programs, sponsored by the U.S. Nuclear Regulatory Commission (USNRC), celebrated 40 years of continuous research oriented toward the safety of light-water nuclear reactor pressure vessels (RPV). This paper presents a summary of results from those programs with a view to future activities.

Nanstad, Randy K [ORNL; Bass, Bennett Richard [ORNL; Rosseel, Thomas M [ORNL; Merkle, John Graham [ORNL; Sokolov, Mikhail A [ORNL

2007-01-01T23:59:59.000Z

360

Development of an internally cooled annular fuel bundle for pressurized heavy water reactors  

SciTech Connect (OSTI)

A number of preliminary studies have been conducted at Atomic Energy of Canada Limited to explore the potential of using internally cooled annular fuel (ICAF) in CANDU reactors including finite element thermo-mechanical modelling, reactor physics, thermal hydraulics, fabrication and mechanical design. The most compelling argument for this design compared to the conventional solid-rod design is the significant reduction in maximum fuel temperature for equivalent LERs (linear element ratings). This feature presents the potential for power up-rating or higher burnup and a decreased defect probability due to in-core power increases. The thermal-mechanical evaluation confirmed the significant reduction in maximum fuel temperatures for ICAF fuel compared to solid-rod fuel for equivalent LER. The maximum fuel temperature increase as a function of LER increase is also significantly less for ICAF fuel. As a result, the sheath stress induced by an equivalent power increase is approximately six times less for ICAF fuel than solid-rod fuel. This suggests that the power-increase thresholds to failure (due to stress-corrosion cracking) for ICAF fuel should be well above those for solid-rod fuel, providing improvement in operation flexibility and safety.

Hamilton, H.; Armstrong, J.; Kittmer, A.; Zhuchkova, A.; Xu, R.; Hyland, B.; King, M.; Nava-Dominguez, A.; Livingstone, S.; Bergeron, A. [Atomic Energy of Canada, Ltd., Chalk River Laboratories, Chalk River, ON (Canada)

2013-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Pressure testing of torispherical heads  

SciTech Connect (OSTI)

Two vessels fabricated from SA516-70 steel with 6% knuckle radius torispherical heads were tested under internal pressure to failure. The D/t ratios of Vessel 1 and Vessel 2 were 238 and 185 respectively. The calculated maximum allowable working pressures of Vessel 1 and 2 heads using the ASME Section 8, Div. 1 rules and measured dimensions were 85 and 110 psi, respectively. Vessel 1 failed at a nozzle weld in the cylindrical shell at 700 psi pressure. Neither buckling nor any other objectionable deformation of the head was observed at a theoretical double-elastic-slope collapse pressure of 241 and a calculated buckling pressure of 270 psi. Buckles were observed developing slowly after 600 psi pressure, and a total of 22 buckles were observed after the test, having the maximum amplitude of 0.15 inch. Vessel 2 failed at the edge of the longitudinal weld of the cylindrical shell at 1,080 psi pressure. Neither buckling nor any other objectionable deformation of the head was observed up to the final pressure, which exceeded the theoretical double-elastic-slope collapse and calculated buckling pressures of 274 psi and 342 psi, respectively.

Rana, M.D. [Praxair, Inc., Tonawanda, NY (United States). Research and Development Dept.; Kalnins, A.; Updike, D.P. [Lehigh Univ., Bethlehem, PA (United States)

1995-12-01T23:59:59.000Z

362

Fluorine Gas Management Guidelines Fluorine is a highly toxic, pale yellow gas about 1.3 times as heavy as air at atmospheric  

E-Print Network [OSTI]

Fluorine Gas Management Guidelines Overview Fluorine is a highly toxic, pale yellow gas about 1.3 times as heavy as air at atmospheric temperature and pressure. Fluorine gas is the most powerful oxidizing agent known, reacting with practically all organic and inorganic substances. Fluorine gas

de Lijser, Peter

363

RF BREAKDOWN STUDIES USING PRESSURIZED CAVITIES  

SciTech Connect (OSTI)

Many present and future particle accelerators are limited by the maximum electric gradient and peak surface fields that can be realized in RF cavities. Despite considerable effort, a comprehensive theory of RF breakdown has not been achieved and mitigation techniques to improve practical maximum accelerating gradients have had only limited success. Part of the problem is that RF breakdown in an evacuated cavity involves a complex mixture of effects, which include the geometry, metallurgy, and surface preparation of the accelerating structures and the make-up and pressure of the residual gas in which plasmas form. Studies showed that high gradients can be achieved quickly in 805 MHz RF cavities pressurized with dense hydrogen gas, as needed for muon cooling channels, without the need for long conditioning times, even in the presence of strong external magnetic fields. This positive result was expected because the dense gas can practically eliminate dark currents and multipacting. In this project we used this high pressure technique to suppress effects of residual vacuum and geometry that are found in evacuated cavities in order to isolate and study the role of the metallic surfaces in RF cavity breakdown as a function of magnetic field, frequency, and surface preparation. One of the interesting and useful outcomes of this project was the unanticipated collaborations with LANL and Fermilab that led to new insights as to the operation of evacuated normal-conducting RF cavities in high external magnetic fields. Other accomplishments included: (1) RF breakdown experiments to test the effects of SF6 dopant in H2 and He gases with Sn, Al, and Cu electrodes were carried out in an 805 MHz cavity and compared to calculations and computer simulations. The heavy corrosion caused by the SF6 components led to the suggestion that a small admixture of oxygen, instead of SF6, to the hydrogen would allow the same advantages without the corrosion in a practical muon beam line. (2) A 1.3 GHz RF test cell capable of operating both at high pressure and in vacuum with replaceable electrodes was designed, built, and power tested in preparation for testing the frequency and geometry effects of RF breakdown at Argonne National Lab. At the time of this report this cavity is still waiting for the 1.3 GHz klystron to be available at the Wakefield Test Facility. (3) Under a contract with Los Alamos National Lab, an 805 MHz RF test cavity, known as the All-Seasons Cavity (ASC), was designed and built by Muons, Inc. to operate either at high pressure or under vacuum. The LANL project to use the (ASC) was cancelled and the testing of the cavity has been continued under the grant reported on here using the Fermilab Mucool Test Area (MTA). The ASC is a true pillbox cavity that has performed under vacuum in high external magnetic field better than any other and has demonstrated that the high required accelerating gradients for many muon cooling beam line designs are possible. (4) Under ongoing support from the Muon Acceleration Program, microscopic surface analysis and computer simulations have been used to develop models of RF breakdown that apply to both pressurized and vacuum cavities. The understanding of RF breakdown will lead to better designs of RF cavities for many applications. An increase in the operating accelerating gradient, improved reliability and shorter conditioning times can generate very significant cost savings in many accelerator projects.

Johnson, Rolland

2014-09-21T23:59:59.000Z

364

A very thin havar film vacuum window for heavy ions to perform radiobiology studies at the BNL Tandem  

SciTech Connect (OSTI)

Heavy ion beams from the BNL Tandem Van de Graaff accelerators will be made available for radiobiology studies on cell cultures. Beam energy losses need to be minimized both in the vacuum window and in the air in order to achieve the ranges required for the cells to be studied. This is particularly challenging for ions heavier than iron. The design is presented of a 0.4-inch diameter Havar film window that will satisfy these requirements. Films as thin as 80 microinches were successfully pressure tested. The final thickness to be used may be slightly larger to help in achieving pin hole free windows. We discuss design considerations and present pressure and vacuum test results as well as tests with heavy ion beams.

Thieberger, P.; Abendroth, H.; Alessi, J.; Cannizzo, L.; Carlson, C.; Gustavsson, A.; Minty, M.; Snydstrup, L.

2011-03-28T23:59:59.000Z

365

Heavy-section steel irradiation program. Progress report, October 1992--March 1993  

SciTech Connect (OSTI)

Maintaining the integrity of the reactor pressure vessel (RPV) in a light-water-cooled nuclear power plant is crucial in preventing and controlling severe accidents that have the potential for major contamination release. The RPV is one of only two more safety-related components of the plant for which a duplicate or redundant backup system does not exist. It is therefore imperative to understand and be able to predict the capabilities and limitations of the integrity inherent in the RPV. In particular, it is vital to fully understand the degree of irradiation-induced degradation of the RPV`s fracture resistance that occurs during service. For this reason, the Heavy-Section Steel Irradiation (HSSI) Program has been established at Oak Ridge National Laboratory (ORNL) under sponsorship of the Nuclear Regulatory Commission (NRC). The primary goal of this major safety program is to provide a thorough, quantitative assessment of the effects of neutron irradiation on the material behavior (in particular, the fracture toughness properties) of typical pressure-vessel steels as they relate to light-water-reactor pressure-vessel integrity. The program centers on experimental assessments of irradiation-induced embrittlement (including the completion of certain irradiation studies previously conducted by the Heavy-Section Steel Technology Program) augmented by detailed examinations and modeling of the accompanying microstructural changes. Effects of specimen size; material chemistry; product form and microstructure; irradiation fluence, flux, temperature, and spectrum; and postirradiation annealing are being examined on a wide range of fracture properties.

Corwin, W.R.

1998-04-01T23:59:59.000Z

366

Characterizing Pleiotropic Effects of Glucocorticoids in Mice Using Heavy Water Labeling and Mass Spectrometry  

E-Print Network [OSTI]

turnover rates by heavy water labeling of nonessential aminocell proliferation by heavy water labeling. Nature protocolscell proliferation by heavy water labeling. American journal

Roohk, Donald Jason

2011-01-01T23:59:59.000Z

367

Pressure Vessel Burst Program: Automated hazard analysis for pressure vessels  

SciTech Connect (OSTI)

The design, development, and use of a Windows based software tool, PVHAZARD, for pressure vessel hazard analysis is presented. The program draws on previous efforts in pressure vessel research and results of a Pressure Vessel Burst Test Study. Prior papers on the Pressure Vessel Burst Test Study have been presented to the ASME, AIAA, JANNAF, NASA Pressure Systems Seminar, and to a DOD Explosives Safety Board subcommittee meeting. Development and validation is described for simplified blast (overpressure/impulse) and fragment (velocity and travel distance) hazard models. The use of PVHAZARD in making structural damage and personnel injury estimates is discussed. Efforts in-progress are reviewed including the addition of two-dimensional and three-dimensional (2D and 3D) hydrodynamic code analyses to supplement the simplified models, and the ability to assess barrier designs for protection from fragmentation.

Langley, D.R. [Aerospace Corp., Kennedy Space Center, FL (United States); Chrostowski, J.D. [ACTA Inc., Torrance, CA (United States); Goldstein, S. [Aerospace Corp., El Segundo, CA (United States); Cain, M. [General Physics Corp., Titusville, FL (United States)

1996-12-31T23:59:59.000Z

368

Self-assembling functionalized single-walled carbon nanotubes  

E-Print Network [OSTI]

W. Wang (2007). "Storage of hydrogen in single-walled carbongravimetric storage capacity of hydrogen in a diamond-shapedfor energy storage applications such as hydrogen absorption.

Gao, Yan

2011-01-01T23:59:59.000Z

369

aligned single wall: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Page Topic Index 1 Printed Multilayer Superstructures of Aligned Single-Walled Carbon Materials Science Websites Summary: Printed Multilayer Superstructures of Aligned...

370

Imaging cell wall architecture in single Zinnia elegans tracheary elements  

E-Print Network [OSTI]

indicated a loss of lignin and a modest loss of otherTEs accumulate lignin in their secondary walls and undergohemicelluloses, and also lignin, a complex aromatic polymer

Lacayo, Catherine

2012-01-01T23:59:59.000Z

371

Seismic design, testing and analysis of reinforced concrete wall buildings  

E-Print Network [OSTI]

of Slender Reinforced Concrete Walls”. Structural Journal,T. (1975). “Reinforced Concrete Structures”. John Wiley &Design of Reinforced Concrete and Masonry Buildings”. John

Panagiotou, Marios

2008-01-01T23:59:59.000Z

372

Electromagnetic Interference (EMI) Shielding of Single-Walled Carbon  

E-Print Network [OSTI]

Electromagnetic Interference (EMI) Shielding of Single-Walled Carbon Nanotube Epoxy Composites Ning (SWNT)-polymer composites have been fabricated to evaluate the electromagnetic interference (EMI

Gao, Hongjun

373

Fracture of welded aluminum thin-walled structures  

E-Print Network [OSTI]

A comprehensive methodology was developed in the thesis for damage prediction of welded aluminum thin-walled structures, which includes material modeling, calibration, numerical simulation and experimental verification. ...

Zheng, Li, Ph. D. Massachusetts Institute of Technology

2006-01-01T23:59:59.000Z

374

Self-assembling functionalized single-walled carbon nanotubes  

E-Print Network [OSTI]

scale synthesis of carbon nanotubes." Nature, Vol.358, 220-Ropes of Metallic Carbon Nanotubes." Science, Vol.273(5274),of single- wall carbon nanotubes. Process, product, and

Gao, Yan

2011-01-01T23:59:59.000Z

375

Self-assembling functionalized single-walled carbon nanotubes  

E-Print Network [OSTI]

Single-walled carbon nanotubes Carbon nanotubes (CNTs) arescale synthesis of carbon nanotubes." Nature, Vol.358, 220-Ropes of Metallic Carbon Nanotubes." Science, Vol.273(5274),

Gao, Yan

2011-01-01T23:59:59.000Z

376

Moisture Management for High R-Value Walls  

SciTech Connect (OSTI)

The following report explains the moisture-related concerns for High R-value wall assemblies and discusses past Building America research work that informs this study. Hygrothermal simulations were prepared for several common approaches to High R-value wall construction in six cities (Houston, Atlanta, Seattle, St. Louis, Chicago, and International Falls) representing a range of climate zones (2, 3, 4C, 4, 5A, and 7, respectively). The simulations are informed by experience gained from past research in this area and validated by field measurement and forensic experience. The modeling program was developed to assess the moisture durability of the wall assemblies based on three primary sources of moisture: construction moisture, air leakage condensation, and bulk water leakage. The peak annual moisture content of the wood based exterior sheathing was used to comparatively analyze the response to the moisture loads for each of the walls in each given city. Walls which experienced sheathing moisture contents between 20% and 28% were identified as risky, whereas those exceeding 28% were identified as very high risk. All of the wall assemblies perform well under idealized conditions. However, only the walls with exterior insulation, or cavity insulation which provides a hygrothermal function similar to exterior insulation, perform adequately when exposed to moisture loads. Walls with only cavity insulation are particularly susceptible to air leakage condensation. None of the walls performed well when a precipitation based bulk water leak was introduced to the backside of the sheathing, emphasizing the importance of proper flashing details.

Lepage, R.; Schumacher, C.; Lukachko, A.

2013-11-01T23:59:59.000Z

377

Oscillating light wall above a sunspot light bridge  

E-Print Network [OSTI]

With the high tempo-spatial \\emph{Interface Region Imaging Spectrograph} 1330 {\\AA} images, we find that many bright structures are rooted in the light bridge of NOAA 12192, forming a \\emph{light wall}. The light wall is brighter than the surrounding areas, and the wall top is much brighter than the wall body. The New Vacuum Solar Telescope H$\\alpha$ and the \\emph{Solar Dynamics Observatory} 171 {\\AA} and 131 {\\AA} images are also used to study the light wall properties. In 1330 {\\AA}, 171 {\\AA}, and 131 {\\AA}, the top of the wall has a higher emission, while in the H$\\alpha$ line, the wall top emission is very low. The wall body corresponds to bright areas in 1330 {\\AA} and dark areas in the other lines. The top of the light wall moves upward and downward successively, performing oscillations in height. The deprojected mean height, amplitude, oscillation velocity, and the dominant period are determined to be 3.6 Mm, 0.9 Mm, 15.4 km s$^{-1}$, and 3.9 min, respectively. We interpret the oscillations of the lig...

Yang, Shuhong; Jiang, Fayu; Xiang, Yongyuan

2015-01-01T23:59:59.000Z

378

artery wall thickness: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

(CCA-IMT) were measured using ultrasonography. Gait 22 LIFE CYCLE ASSESSMENT OF A HEMP CONCRETE WALL: IMPACT OF THICKNESS AND COATING. Physics Websites Summary: to reduce...

379

Moisture Management of High-R Walls (Fact Sheet)  

SciTech Connect (OSTI)

The following report explains the moisture-related concerns for High R-value wall assemblies and discusses past Building America research work that informs this study. Hygrothermal simulations were prepared for several common approaches to High R-value wall construction in six cities (Houston, Atlanta, Seattle, St. Louis, Chicago, and International Falls) representing a range of climate zones (2, 3, 4C, 4, 5A, and 7, respectively). The simulations are informed by experience gained from past research in this area and validated by field measurement and forensic experience. The modeling program was developed to assess the moisture durability of the wall assemblies based on three primary sources of moisture: construction moisture, air leakage condensation, and bulk water leakage. The peak annual moisture content of the wood based exterior sheathing was used to comparatively analyze the response to the moisture loads for each of the walls in each given city. Walls which experienced sheathing moisture contents between 20% and 28% were identified as risky, whereas those exceeding 28% were identified as very high risk. All of the wall assemblies perform well under idealized conditions. However, only the walls with exterior insulation, or cavity insulation which provides a hygrothermal function similar to exterior insulation, perform adequately when exposed to moisture loads. Walls with only cavity insulation are particularly susceptible to air leakage condensation. None of the walls performed well when a precipitation based bulk water leak was introduced to the backside of the sheathing, emphasizing the importance of proper flashing details.

Not Available

2013-12-01T23:59:59.000Z

380

Seismic design, testing and analysis of reinforced concrete wall buildings  

E-Print Network [OSTI]

based on the material testing data of concrete cylinders inDESIGN, TESTING AND ANALYSIS OF REINFORCED CONCRETE WALLDESIGN, TESTING AND ANALYSIS OF REINFORCED CONCRETE WALL

Panagiotou, Marios

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Wall and laser spot motion in cylindrical hohlraums  

SciTech Connect (OSTI)

Wall and laser spot motion measurements in empty, propane-filled and plastic (CH)-lined gold coated cylindrical hohlraums were performed on the Omega laser facility [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. Wall motion was measured using axial two-dimensional (2D) x-ray imaging and laser spot motion was perpendicularly observed through a thinned wall using streaked hard x-ray imaging. Experimental results and 2D hydrodynamic simulations show that while empty targets exhibit on-axis plasma collision, CH-lined and propane-filled targets inhibit wall expansion, corroborated with perpendicular streaked imaging showing a slower motion of laser spots.

Huser, G.; Courtois, C.; Monteil, M.-C. [CEA, DAM, DIF, F-91297 Arpajon (France)

2009-03-15T23:59:59.000Z

382

An Estimate of the Thermodynamic Pressure in High-Energy Collisions  

E-Print Network [OSTI]

We introduce a novel approach to estimate the thermodynamic pressure from heavy-ion collisions based on recently measured higher-order moments of particle multiplicities by the STAR experiment. We start with fitting the experimental results in the most-central collisions. Then, we integrate them back to lower ones. For example, we find that the first-order moment, the mean multiplicity, is exactly reproduced from the integral of variance, the second-order moment. Therefore, the zero-order moment, the thermodynamic pressure, can be estimated from the integral of the mean multiplicity. the possible comparison between such a kind of pressure (deduced from the integral of particle multiplicity) and the lattice pressure and the relating of Bjorken energy density to the lattice energy density are depending on lattice QCD at finite baryon chemical potential and first-principle estimation of the formation time of the quark-gluon plasma (QGP).

Tawfik, Abdel Nasser

2015-01-01T23:59:59.000Z

383

Heavy Truck Clean Diesel Cooperative Research Program  

SciTech Connect (OSTI)

This report is the final report for the Department of Energy on the Heavy Truck Engine Program (Contract No. DE-FC05-00OR22806) also known as Heavy Truck Clean Diesel (HTCD) Program. Originally, this was scoped to be a $38M project over 5 years, to be 50/50 co-funded by DOE and Caterpillar. The program started in June 2000. During the program the timeline was extended to a sixth year. The program completed in December 2006. The program goal was to develop and demonstrate the technologies required to enable compliance with the 2007 and 2010 (0.2g/bhph NOx, 0.01g/bhph PM) on-highway emission standards for Heavy Duty Trucks in the US with improvements in fuel efficiency compared to today's engines. Thermal efficiency improvement from a baseline of 43% to 50% was targeted.

Milam, David

2006-12-31T23:59:59.000Z

384

Fluid catalytic cracking of heavy petroleum fractions  

SciTech Connect (OSTI)

A process is claimed for fluid catalytic cracking of residuum and other heavy oils comprising of gas oil, petroleum residue, reduced and whole crudes and shale oil to produce gasoline and other liquid products which are separated in various streams in a fractionator and associated vapor recovery equipment. The heat from combustion of coke on the coked catalyst is removed by reacting sulfur-containing coke deposits with steam and oxygen in a separate stripper-gasifier to produce a low btu gas stream comprising of sulfur compounds, methane, carbon monoxide, hydrogen, and carbon dioxide at a temperature of from about 1100/sup 0/F. To about 2200/sup 0/F. The partially regenerated catalyst then undergoes complete carbon removal in a regeneration vessel. The regenerated catalyst is recycled for re-use in the cracking of heavy petroleum fractions. The liquid products are gasoline, distillates, heavy fuel oil, and light hydrocarbons.

McHenry, K.W.

1981-06-30T23:59:59.000Z

385

High energy heavy ions: techniques and applications  

SciTech Connect (OSTI)

Pioneering work at the Bevalac has given significant insight into the field of relativistic heavy ions, both in the development of techniques for acceleration and delivery of these beams as well as in many novel areas of applications. This paper will outline our experiences at the Bevalac; ion sources, low velocity acceleration, matching to the synchrotron booster, and beam delivery. Applications discussed will include the observation of new effects in central nuclear collisions, production of beams of exotic short-lived (down to 1 ..mu..sec) isotopes through peripheral nuclear collisions, atomic physics with hydrogen-like uranium ions, effects of heavy ''cosmic rays'' on satellite equipment, and an ongoing cancer radiotherapy program with heavy ions. 39 refs., 6 figs., 1 tab.

Alonso, J.R.

1985-04-01T23:59:59.000Z

386

Steam quality determination using pressure and temperature measurements in a venturi  

E-Print Network [OSTI]

1987 Steam (tuality Ue~tion using Pressure and ~tuze Measurements M A Venturi(December 1987) Benny leo O' Neil, B. S ~ Texas A & M University Chairman of Advisory Crmsittee: Dr. R. A. Staztnaan Steam injecticn into heavy oil reservoirs accounted...-Rmse Flow 'Ihrough Venturi. . . TABID 2: Pressures and ~tures Gorrespanding to location on Heat E&n9anger. 25 59 LI87 OF FIGURES FIGURE 1: Steam distribution network facilities. . FIGURE 2: Counter flow heat exchanger FIGURE 3: Gas fired stan...

O'Neil, Danny Leo

2012-06-07T23:59:59.000Z

387

Electrokinetically pumped high pressure sprays  

DOE Patents [OSTI]

An electrokinetic pump capable of producing high pressure is combined with a nozzle having a submicron orifice to provide a high pressure spray device. Because of its small size, the device can be contained within medical devices such as an endoscope for delivering biological materials such as DNA, chemo therapeutic agents, or vaccines to tissues and cells.

Schoeniger, Joseph S. (Oakland, CA); Paul, Phillip H. (Livermore, CA); Schoeniger, Luke (Pittsford, NY)

2002-01-01T23:59:59.000Z

388

Possible Pressure Effect for Superconductors  

E-Print Network [OSTI]

We make an estimate of the possible range of $\\Delta T_c$ induced by high-pressure effects in post-metallic superconductors by using the theory of {\\it extended irreversible/reversible thermodynamics} and Pippard's length scale. The relationship between the increment of the superconducting temperature and the increase of the pressure is parabolic.

A. Kwang-Hua Chu

2005-08-30T23:59:59.000Z

389

Vapour extraction (VAPEX) process for recovery of heavy oil and bitumen  

SciTech Connect (OSTI)

For over 90% of the vast resources of bitumen and heavy oil in Canada, in situ recovery processes have to be developed to produce and utilize them efficiently and economically. Thermal recovery processes using steam, although effective for thick reservoirs with good quality sands, are increasingly proving to be uneconomical, particularly for thin, shaley, or bottom water reservoirs. The inefficiency is caused by large heat losses, high water requirement, extensive surface facilities, and adverse environmental impact. To overcome these problems, a new non-thermal vapour extraction (VAPEX) process has been developed. The process is closely related to the Steam-Assisted Gravity Drainage (SAGD) concept. However, in the VAPEX process the steam chamber is replaced with a chamber containing light hydrocarbon vapours close to its dew point at the reservoir pressure. If the pressure used is close to the saturation pressure of hydrocarbons, deasphalting may occur in the reservoir causing a substantial reduction in viscosity and heavy metal contents. Experiments conducted in a Hele-Shaw cell and in a 2D physical scaled model using Lloydminster, Cold Lake, and Peace River heavy oil/bitumen and ethane, propane, and butane as solvents demonstrated that this process is very promising technically as well as economically. An active aquifer underlying the bitumen zone made the reservoir more valuable because of spreading of the solvent vapour directly underneath the formation which increased the vapour-bitumen contact extensively. The investigation was extended from a dual horizontal continuous injection/production well strategy described above to a single horizontal well cyclic process for the Cold Lake reservoir in a 3D physical scaled model. The tests illustrated that ethane was an effective solvent in producing Cold Lake bitumen and that the cyclic VAPEX process has the potential to be a breakthrough recovery technology.

Jha, K.N. [CANMET, Ottawa, Ontario (Canada); Butler, R.M. [Univ. of Calgary, Alberta (Canada); Lim, G.B. [Imperial Oil Resources Limited, Calgary, Alberta (Canada)] [and others

1995-12-31T23:59:59.000Z

390

Fundamentals of high pressure adsorption  

SciTech Connect (OSTI)

High-pressure adsorption attracts research interests following the world's attention to alternative fuels, and it exerts essential effect on the study of hydrogen/methane storage and the development of novel materials addressing to the storage. However, theoretical puzzles in high-pressure adsorption hindered the progress of application studies. Therefore, the present paper addresses the major theoretical problems that challenged researchers: i.e., how to model the isotherms with maximum observed in high-pressure adsorption; what is the adsorption mechanism at high pressures; how do we determine the quantity of absolute adsorption based on experimental data. Ideology and methods to tackle these problems are elucidated, which lead to new insights into the nature of high-pressure adsorption and progress in application studies, for example, in modeling multicomponent adsorption, hydrogen storage, natural gas storage, and coalbed methane enrichment, was achieved.

Zhou, Y.P.; Zhou, L. [Tianjin University, Tianjin (China). High Pressure Adsorption Laboratory

2009-12-15T23:59:59.000Z

391

Heat transfer and pressure drop in an annular channel with downflow  

SciTech Connect (OSTI)

The onset of a flow instability (OFI) determines the minimum flow rate for cooling in the flow channels of a nuclear fuel assembly. A test facility was constructed with full-scale models (length and diameter) of annular flow channels incorporating many instruments to measure heat transfer and pressure drop with downflow in the annulus. Tests were performed both with and without axial centering ribs at prototypical values of pressure, flow rate and uniform wall heat flux. The axial ribs have the effect of subdividing the annulus into quadrants, so the problem becomes one of parallel channel flow, unlike previous experiments in tubes (upflow and downflow). Other tests were performed to determine the effects if any of asymmetric and non-uniform circumferential wall heating, operating pressure level and dissolved gas concentration. Data from the tests are compared with models for channel heat transfer and pressure drop profiles in several regimes of wall heating from single-phase forced convection through partially and fully developed nucleate boiling. Minimum stable flow rates were experimentally determined as a function of wall heat flux and heat distribution and compared with the model for the transition to fully developed boiling which is a key criterion in determining the OFI condition in the channel. The heat transfer results in the channel without ribs are in excellent agreement with predictions from a computer model of the flow in the annulus and with empirical correlations developed from similar tests. The test results with centering ribs show that geometrical variations between the channels can lead to differences in subchannel behavior which can make the effect of the ribs and the geometry an important factor when assessing the power level at which the fuel assembly (and the reactor) can be operated to prevent overheating in the event of a loss-of-coolant-accident (LOCA).

Dolan, F.X.; Crowley, C.J. [Creare, Inc., Hanover, NH (United States); Qureshi, Z.H. [Westinghouse Savannah River Co., Aiken, SC (United States)

1992-06-01T23:59:59.000Z

392

Heat transfer and pressure drop in an annular channel with downflow  

SciTech Connect (OSTI)

The onset of a flow instability (OFI) determines the minimum flow rate for cooling in the flow channels of a nuclear fuel assembly. A test facility was constructed with full-scale models (length and diameter) of annular flow channels incorporating many instruments to measure heat transfer and pressure drop with downflow in the annulus. Tests were performed both with and without axial centering ribs at prototypical values of pressure, flow rate and uniform wall heat flux. The axial ribs have the effect of subdividing the annulus into quadrants, so the problem becomes one of parallel channel flow, unlike previous experiments in tubes (upflow and downflow). Other tests were performed to determine the effects if any of asymmetric and non-uniform circumferential wall heating, operating pressure level and dissolved gas concentration. Data from the tests are compared with models for channel heat transfer and pressure drop profiles in several regimes of wall heating from single-phase forced convection through partially and fully developed nucleate boiling. Minimum stable flow rates were experimentally determined as a function of wall heat flux and heat distribution and compared with the model for the transition to fully developed boiling which is a key criterion in determining the OFI condition in the channel. The heat transfer results in the channel without ribs are in excellent agreement with predictions from a computer model of the flow in the annulus and with empirical correlations developed from similar tests. The test results with centering ribs show that geometrical variations between the channels can lead to differences in subchannel behavior which can make the effect of the ribs and the geometry an important factor when assessing the power level at which the fuel assembly (and the reactor) can be operated to prevent overheating in the event of a loss-of-coolant-accident (LOCA).

Dolan, F.X.; Crowley, C.J. (Creare, Inc., Hanover, NH (United States)); Qureshi, Z.H. (Westinghouse Savannah River Co., Aiken, SC (United States))

1992-01-01T23:59:59.000Z

393

Water heat pipe frozen startup and shutdown transients with internal temperature, pressure and visual observations  

E-Print Network [OSTI]

with Internal Temperature, Pressure and Visual Observations. IDecember 1989) Thomas Raymond Reinarts, B. S. , Texas A8M University Chair of Advisory Committee: Dr. Frederick Best In a set of transient heat pipe experiments vapor space and wick... LIST OF TABLES Page Table 1. Outer Aluminum Wall Temperatures Observed and Predicted 79 Table 2. Summary of Measured Dryout, Rewet and Melting Front 126 Velocities LIST OF FIGURES Figure 1. Typical Heat Pipe Diagram Figure 2. Curvature of Vapor...

Reinarts, Thomas Raymond

1989-01-01T23:59:59.000Z

394

Simulation of heavy oil reservoir performance using a non-Newtonian flow model  

E-Print Network [OSTI]

. This reduction of viscosity as a function of shear rate has a significant effect on rates and other parameters when simulating reservoir performance. The objective of this study is to compare the simulation results of Newtonian and non-Newtonian oils under...)ected to increasing shear rate, the viscosity decreases. This behavior implies that the oil viscosity varies as a function of not only pressure, but also shear rate. This behavior is important when simulating heavy-oil reservoir performance. To simulate the flow...

Narahara, Gene Masao

1983-01-01T23:59:59.000Z

395

Influence of increased static pressure in MHD-channel of hypervelocity wind tunnel on its characteristics  

SciTech Connect (OSTI)

One of the main weaknesses of available MHD gas acceleration wind tunnels which restricts their application for simulating vehicle re-entry flights and reproducing scramjet combustion chamber conditions is a relatively low static pressure in the channel (P{approximately}0.1 to 0.2 Atm). The possibility of increasing this pressure and the influence of the increased pressure on the MHD-accelerator characteristics are the subject of the present paper. It is shown that the main challenge is the necessity of increasing the total Lorentz force proportionally to the channel gas density at electrode current density not resulting in heat and electrical breakdown and the development of the side walls and interelectrode insulators designed for higher heat fluxes, q {approximately} 5 to 10 kw/cm{sup 2}. Some possible wall design versions are suggested. The influence of increased pressure is investigated using the Faraday - type MED channel at static pressures in the MHD channel from 0.2 to 1.0 Atm and total accelerating current I = 300 to 1,100 Amps when B=2.5T. Forty five electrodes are used in the MHD channel at maximum current density of 50 A/cm{sup 2}. The channel flow is calculated by applying the model of a gas in thermodynamic equilibrium. The influence of the increased pressure on electrodynamic (accelerator electrode voltages and currents, Hall voltage and current) and gasdynamic (distributions of static pressure, temperature, velocity, Mach numbers, etc., along the channel length) characteristics is evaluated. Some recommendations on the development of MHD channels for hypersonic wind tunnels designed for high pressure are suggested.

Alfyorov, V.I.; Rudakova, A.P.; Rukavets, V.P.; Shcherbakov, G.I. [Central Aerohydrodynamic Institute (TsAGI), Zhukovsky (Russian Federation)

1995-12-31T23:59:59.000Z

396

HEAVY-DUTY TRUCK EMISSIONS AND FUEL CONSUMPTION SIMULATING REAL...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

HEAVY-DUTY TRUCK EMISSIONS AND FUEL CONSUMPTION SIMULATING REAL-WORLD DRIVING IN LABORATORY CONDITIONS HEAVY-DUTY TRUCK EMISSIONS AND FUEL CONSUMPTION SIMULATING REAL-WORLD DRIVING...

397

Development and Demonstration of Fischer-Tropsch Fueled Heavy...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

(F-T) Fuels in the U.S. -- An Overview APBF-DEC Heavy Duty NOx AdsorberDPF Project: Heavy Duty Linehaul Platform Project Update Coal-Derived Liquids to Enable HCCI Technology...

398

Enhanced Bioaccumulation of Heavy Metals by Bacterial Cells Displaying  

E-Print Network [OSTI]

Enhanced Bioaccumulation of Heavy Metals by Bacterial Cells Displaying Synthetic Phytochelatins for enhanced bioaccumulation of toxic metals. Synthetic genes encoding for several metal strategy for develop- ing high-affinity bioadsorbents suitable for heavy metal removal. © 2000 John Wiley

Chen, Wilfred

399

Difficulty of Measuring Emissions from Heavy-Duty Engines Equipped...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Difficulty of Measuring Emissions from Heavy-Duty Engines Equipped with SCR and DPF Difficulty of Measuring Emissions from Heavy-Duty Engines Equipped with SCR and DPF In reference...

400

Development of a 16-MW sub th coal-water/heavy oil burner for front-wall firing  

SciTech Connect (OSTI)

The Canadian program of coal-water fuel (CWF) technology development has included the demonstration of commercial burners for CWF in both coal and oil-designed utility boilers. The demonstrations clearly showed that these burners were prototypes, and were, in fact, modified oil burners that were mismatched to the rheological properties of the CWF. As the demonstrations were proceeding, a simultaneous research program was undertaken in which the basic principles governing atomization and combustion of CWF were studied. Results from the fundamental studies which led to the development of a novel prototype dual fuel CWF/oil burner are described. In the various stages of development, the burner was scaled up from 1.5 MW{sub th} to an industrial scale of 16 MS{sub th} for demonstration in a 20-MW{sub (e)} oil-designed industrial utility boiler and for a single-burner commercial operation in an oil designed package steam boiler. A summary of the burner performance in these demonstrations is also given in this paper.

Thambimuthu, K.V.; Whaley, H. (EMR Canada/CANMET, Ottawa (CA)); Bennet, A.; Jonasson, K.A. (NRC Canada, Ottawa (CA))

1990-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

A photoelastic study of the stress concentrations at the fillets in a closed end heavy wall cylinder  

E-Print Network [OSTI]

1 crates the reaction, This combination of factors results in large temper- ature gradients, and these gradients are believed to account for the resi dual stresses. Those residual stresses cannot be removed by annealing~ stran~wly however...? 43. 5 . 175 . 166 32. 0 ~ 186 V. 7 . 21 17 2 23 12 2 ~ 23 9. 16 . 225 s, =i t P-R AV4 BS, (P-R) Z. S~ lg)(?~) . 103 l, . 70 . 103 3. 10 103 2, 0 . 103 1. 34 103 95 ~ 85 , 61 P= lf. 7 1. 0 1. 103 1. 206 1. 309 1. 412 1 515 0 (0...

Cloud, Robert Lea

1957-01-01T23:59:59.000Z

402

TERMINATION OF THE POROUS WALL CONCEPT To: APEX GROUP  

E-Print Network [OSTI]

TERMINATION OF THE POROUS WALL CONCEPT To: APEX GROUP From: Anter El-Azab (anter@seas.ucla.edu) Re with Lithium will can not work and this concept should be terminated. For the case of vanadium alloy on this concept should be terminated. #12;TERMINATION OF THE POROUS WALL CONCEPT Best Regards, Anter #12;

California at Los Angeles, University of

403

Wall Sculpture by Ellsworth Kelly Installed on Dartmouth Campus  

E-Print Network [OSTI]

Wall Sculpture by Ellsworth Kelly Installed on Dartmouth Campus Dartmouth Panels will be dedicated District, a wall sculpture by renowned abstract artist Ellsworth Kelly has been installed on the eastern façade of the Hopkins Center for the Arts, facing the Visual Arts Center. Kelly was in attendance

Shepherd, Simon

404

NON-RECTANGULAR RC WALLS: A REVIEW ON EXPERIMENTAL INVESTIGATIONS  

E-Print Network [OSTI]

section. It was rare that tests were done using load paths that did not follow the principal axes subjected to unidirectional or bidirectional loading along one or both of the principal axes of the wall-sections such as for example L-shaped or U-shaped walls which were tested under quasi-static or dynamic loads. The tests

Thévenaz, Jacques

405

Liquid Lithium Wall Experiments in CDX-U R. Majeski,  

E-Print Network [OSTI]

Liquid Lithium Wall Experiments in CDX-U R. Kaita, a R. Majeski, a S. Luckhardt, b R. Doerner, b M ABSTRACT The concept of a flowing lithium first wall for a fusion reactor may lead to a significant advance is intensely heated and well diagnosed, and an extensive liquid lithium plasma-facing surface will be used

California at Los Angeles, University of

406

Optical absorption intensity of semiconductor single-wall carbon nanotubes  

E-Print Network [OSTI]

Optical absorption intensity of semiconductor single-wall carbon nanotubes Y. Oyama1 , R. Saito1. The optical absorption intensity is inversely proportional to the diameter in the unit of per carbon atom of single-wall carbon nanotubes (SWNT) synthesized by alcohol CCVD (ACCVD) method and HiPco method [1

Maruyama, Shigeo

407

Absorption spectroscopy of individual single-walled carbon nanotubes  

E-Print Network [OSTI]

Absorption spectroscopy of individual single-walled carbon nanotubes Stéphane Berciaud,a Laurent-walled carbon nanotubes (SWNTs) lead to heterogeneous samples containing mixtures of metallic and semiconducting species with a variety of lengths and defects. Optical detection at the single nanotube level should thus

Boyer, Edmond

408

Quantum rotation of hydrogen in single-wall carbon nanotubes  

E-Print Network [OSTI]

Quantum rotation of hydrogen in single-wall carbon nanotubes C.M. Brown a,b , T. Yildirim b , D containing single-wall carbon nanotubes. These materials have attracted considerable interest recently due the ortho±para conversion of physisorbed hydrogen in a nanotube containing soot loaded with hydrogen. From

Yildirim, Taner

409

Simulations of nanosensors based on single walled carbon nanotubes  

E-Print Network [OSTI]

Simulations of nanosensors based on single walled carbon nanotubes Polina Pine1, Yuval E. Yaish2. The potential of single-walled carbon nanotubes as mass sensors is examined. The change in mass leads to proportional changes in the nanotube vibrational frequencies, which are monitored during atomistic simulations

Adler, Joan

410

Scanning tunneling spectroscopy of suspended single-wall carbon nanotubes  

E-Print Network [OSTI]

Scanning tunneling spectroscopy of suspended single-wall carbon nanotubes B. J. LeRoy,a) S. G-wall carbon nanotubes that are freely suspended over a trench. The nanotubes were grown by chemical vapor on the freestanding portions of the nanotubes. Spatially resolved spectroscopy on the suspended portion of both

Dekker, Cees

411

Characterization of single wall carbon nanotubes by nonane preadsorption  

E-Print Network [OSTI]

energy for nitrogen adsorbed in nanotubes at zero coverage within the range of 12­18 kJ/mol. This bindingCharacterization of single wall carbon nanotubes by nonane preadsorption Oleg Byl a , Jie Liu b The preferential blocking of the interior adsorption sites of single walled carbon nanotubes (SWNTs) by n

Liu, Jie

412

Electrical Transport in Single-Wall Carbon Nanotubes  

E-Print Network [OSTI]

. (a) Schematic view a nanotube field-effect transistor (b) The Dirac energy dispersion coneElectrical Transport in Single-Wall Carbon Nanotubes Michael J. Biercuk1,3 , Shahal Ilani2 metal and semiconducting single-wall carbon nanotubes. The fundamental scattering mechanisms governing

McEuen, Paul L.

413

Raman Measurements on Electrochemically Doped Single-Walled Carbon Nanotubes  

E-Print Network [OSTI]

Raman Measurements on Electrochemically Doped Single-Walled Carbon Nanotubes P. M. Rafailov, M and studied the Raman response of electro- chemically doped single-walled carbon nanotubes (SWNT) using different salt solutions. The fre- quency shift of the radial breathing mode (RBM) and the high-energy mode

Nabben, Reinhard

414

ORIGINAL PAPER Hydrothermal process synthesized electrocatalytic multi-walled  

E-Print Network [OSTI]

ORIGINAL PAPER Hydrothermal process synthesized electrocatalytic multi-walled carbon nanotubes as MWCNTs-Au, have been successfully prepared by a facile hydrothermal pro- cess of gold(III) chloride (Au. Keywords Hydrothermal Á Composites Á Au microparticles Á Multi-walled carbon nanotubes Á Ethanol oxidation

Guo, John Zhanhu

415

Optical microcavity with semiconducting single-wall carbon nanotubes  

E-Print Network [OSTI]

Optical microcavity with semiconducting single- wall carbon nanotubes Etienne Gaufrès,1 Nicolas-Perot microcavities based on semiconducting single-wall carbon nanotubes with a quality factor of 160. We properties References and links 1. P. Avouris, M. Freitag and V. Perebeinos, "Carbon nanotube photonics

Paris-Sud XI, Université de

416

Laser-produced plasma-wall interaction O. RENNER,1  

E-Print Network [OSTI]

Laser-produced plasma-wall interaction O. RENNER,1 R. LISKA,2 AND F.B. ROSMEJ3,4 1 Institute, France (RECEIVED 30 August 2009; ACCEPTED 21 September 2009) Abstract Jets of laser­generated plasma surfaces (walls). The pilot experiments carried out on the iodine laser system (5­200 J, 0.44 mm, 0

Liska, Richard

417

Electron-wall interaction in Hall thrustersa... Y. Raitsesb  

E-Print Network [OSTI]

Electron-wall interaction in Hall thrustersa... Y. Raitsesb and D. Staack Princeton Plasma Physics; accepted 22 February 2005; published online 2 May 2005 Electron-wall interaction effects in Hall thrusters this threshold, the electron energy gain is constant in the acceleration region and therefore, secondary electron

418

A Better Method for Evaluating Heavy Metal Water Pollution  

E-Print Network [OSTI]

Method for Evaluating Heavy Metal Water Pollution Janetheavy metal contamination would also help communities evaluate their water

Hering, Janet

2002-01-01T23:59:59.000Z

419

Heavy-quark correlations in deep inelastic scattering  

E-Print Network [OSTI]

We discuss results for heavy quark correlations in next-to-leading order QCD in deep inelastic electroproduction.

J. Smith; B. W. Harris

1996-05-20T23:59:59.000Z

420

Flow and equation of state in heavy-ion collisions  

E-Print Network [OSTI]

The status of flow in heavy-ion collisions and of inference of hadronic-matter properties is reviewed.

Danielewicz, P

1999-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Flow and equation of state in heavy-ion collisions  

E-Print Network [OSTI]

The status of flow in heavy-ion collisions and of inference of hadronic-matter properties is reviewed.

P. Danielewicz

1999-07-25T23:59:59.000Z

422

Flow and equation of state in heavy ion collisions (2)  

E-Print Network [OSTI]

The status of flow in heavy-ion collisions and of inference of hadronic-matter properties is reviewed.

Danielewicz, P

2001-01-01T23:59:59.000Z

423

Measurements of Heavy Flavour Production at ATLAS and CMS  

E-Print Network [OSTI]

New and updated (after the previous Moriond QCD) ATLAS and CMS results on heavy flavour production are reviewed.

Gladilin, Leonid; The ATLAS collaboration

2015-01-01T23:59:59.000Z

424

Flavor Physics Data from the Heavy Flavor Averaging Group (HFAG)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

The Heavy Flavor Averaging Group (HFAG) was established at the May 2002 Flavor Physics and CP Violation Conference in Philadelphia, and continues the LEP Heavy Flavor Steering Group's tradition of providing regular updates to the world averages of heavy flavor quantities. Data are provided by six subgroups that each focus on a different set of heavy flavor measurements: B lifetimes and oscillation parameters, Semi-leptonic B decays, Rare B decays, Unitarity triangle parameters, B decays to charm final states, and Charm Physics.

425

Systems of two heavy quarks with effective field theories  

E-Print Network [OSTI]

I discuss results and applications of QCD nonrelativistic effective field theories for systems with two heavy quarks.

Nora Brambilla

2006-09-22T23:59:59.000Z

426

Electroproduction of heavy quarks at NLO  

E-Print Network [OSTI]

A new next-to-leading order Monte Carlo program for the calculation of fully differential heavy quark cross sections in electroproduction is described. A comparison between the theoretical predictions and the latest charm production data from H1 and ZEUS at HERA is presented.

B. W. Harris

1996-08-20T23:59:59.000Z

427

Research in heavy-ion nuclear physics  

SciTech Connect (OSTI)

This report discusses the following topics: Fusion-fission in light nuclear systems; High-resolution Q-value measurement for the {sup 24}Mg+{sup 24}Mg reaction; Heavy-ion reactions and limits to fusion; and Hybrid MWPC-Bragg curve detector development.

Sanders, S.J.; Prosser, F.W.

1992-01-01T23:59:59.000Z

428

Heavy duty transport research needs assessment  

SciTech Connect (OSTI)

As a result of the desire to decrease the dependence of the US on foreign petroleum as a transportation fuel, this report assesses the research needs to further develop heavy duty engines. The topics covered include diesel engines, alternative fuels, electric vehicle technology, gas turbine engines, and stirling cycle alternative engines. (GHH)

Not Available

1991-09-13T23:59:59.000Z

429

Recent advances in heavy quark theory  

SciTech Connect (OSTI)

Some recent developments in heavy quark theory are reviewed. Particular emphasis is given to inclusive weak decays of hadrons containing a b quark. The isospin violating hadronic decay D{sub s}* {yields} D{sub s}{sup pi}{sup 0} is also discussed.

Wise, M. [California Institute of Technology, Pasadena, CA (United States)

1997-01-01T23:59:59.000Z

430

STAR Highlights on Heavy Ion Physics  

E-Print Network [OSTI]

RHIC-STAR is a mid-rapidity collider experiment for studying high energy nuclear collisions. The main physics goals of STAR experiment are 1) studying the properties of the strongly coupled Quark Gluon Plasma, 2) explore the QCD phase diagram structure. In these proceedings, we will review the recent results of heavy ion physics at STAR.

Shusu Shi

2014-09-30T23:59:59.000Z

431

Heavy Flavour Physics at CMS and ATLAS  

E-Print Network [OSTI]

Prospects for heavy flavour studies with the CMS and ATLAS detectors are presented. Many studies are aimed for early LHC data, taking advantage of the large $b$ production cross-section. Rare decay studies as the $B_s \\to \\mu^+\\mu^-$ decay have also been performed.

L. Wilke; for the CMS; ATLAS Collaborations

2009-05-26T23:59:59.000Z

432

Causal dissipative hydrodynamics for heavy ion collisions  

E-Print Network [OSTI]

We briefly discuss the recent developments in causal dissipative hydrodynamic for relativistic heavy ion collisions. Phenomenological estimate of QGP viscosity over entropy ratio from several experimental data, e.g. STAR's $\\phi$ meson data, centrality dependence of elliptic flow, universal scaling elliptic flow etc. are discussed. QGP viscosity, extracted from hydrodynamical model analysis can have very large systematic uncertainty due to uncertain initial conditions.

Chaudhuri, A K

2011-01-01T23:59:59.000Z

433

Causal dissipative hydrodynamics for heavy ion collisions  

E-Print Network [OSTI]

We briefly discuss the recent developments in causal dissipative hydrodynamic for relativistic heavy ion collisions. Phenomenological estimate of QGP viscosity over entropy ratio from several experimental data, e.g. STAR's $\\phi$ meson data, centrality dependence of elliptic flow, universal scaling elliptic flow etc. are discussed. QGP viscosity, extracted from hydrodynamical model analysis can have very large systematic uncertainty due to uncertain initial conditions.

A. K. Chaudhuri

2011-01-23T23:59:59.000Z

434

Thermal processes for heavy oil recovery  

SciTech Connect (OSTI)

This status report summarizes the project BE11B (Thermal Processes for Heavy Oil Recovery) research activities conducted in FY93 and completes milestone 7 of this project. A major portion of project research during FY93 was concentrated on modeling and reservoir studies to determine the applicability of steam injection oil recovery techniques in Texas Gulf Coast heavy oil reservoirs. In addition, an in-depth evaluation of a steamflood predictive model developed by Mobil Exploration and Production Co. (Mobil E&P) was performed. Details of these two studies are presented. A topical report (NIPER-675) assessing the NIPER Thermal EOR Research Program over the past 10 years was also written during this fiscal year and delivered to DOE. Results of the Gulf Coast heavy oil reservoir simulation studies indicated that though these reservoirs can be successfully steamflooded and could recover more than 50% of oil-in-place, steamflooding may not be economical at current heavy oil prices. Assessment of Mobil E&P`s steamflood predictive model capabilities indicate that the model in its present form gives reasonably good predictions of California steam projects, but fails to predict adequately the performance of non-California steam projects.

Sarkar, A.K.; Sarathi, P.S.

1993-11-01T23:59:59.000Z

435

Heavy Flavors in High Energy ep Collisions  

E-Print Network [OSTI]

Most recent measurements of open charm and beauty production in high energy ep collisions at HERA are reviewed. The measurements explored the different aspects of quantum chromodynamics involved in the process of heavy flavor production. The results are compared with perturbative theoretical calculations at next-to-leading order.

Meng Wang

2005-10-14T23:59:59.000Z

436

BARC TIFR Heavy Ion Accelerator Facility  

E-Print Network [OSTI]

enterprise using accelerated heavy ion beams is to unravel the complexities of the nuclear world in all by the accelerator. The projectile impinges on a target nucleus with enough energy to overcome the electrostatic repulsion so that the collision process is governed by the nuclear interactions. Using a variety

Shyamasundar, R.K.

437

Methods for degrading or converting plant cell wall polysaccharides  

DOE Patents [OSTI]

The present invention relates to methods for converting plant cell wall polysaccharides into one or more products, comprising: treating the plant cell wall polysaccharides with an effective amount of a spent whole fermentation broth of a recombinant microorganism, wherein the recombinant microorganism expresses one or more heterologous genes encoding enzymes which degrade or convert the plant cell wall polysaccharides into the one or more products. The present invention also relates to methods for producing an organic substance, comprising: (a) saccharifying plant cell wall polysaccharides with an effective amount of a spent whole fermentation broth of a recombinant microorganism, wherein the recombinant microorganism expresses one or more heterologous genes encoding enzymes which degrade or convert the plant cell wall polysaccharides into saccharified material; (b) fermenting the saccharified material of step (a) with one or more fermenting microoganisms; and (c) recovering the organic substance from the fermentation.

Berka, Randy (Davis, CA); Cherry, Joel (Davis, CA)

2008-08-19T23:59:59.000Z

438

Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty...  

Broader source: Energy.gov (indexed) [DOE]

and CFD Modeling of In-Cylinder Chemical and Physical Processes * Combine planar laser-imaging diagnostics in an optical heavy-duty engine with multi-dimensional computer...

439

Electrokinetic high pressure hydraulic system  

DOE Patents [OSTI]

A compact high pressure hydraulic pump having no moving mechanical parts for converting electric potential to hydraulic force. The electrokinetic pump, which can generate hydraulic pressures greater than 2500 psi, can be employed to compress a fluid, either liquid or gas, and manipulate fluid flow. The pump is particularly useful for capillary-base systems. By combining the electrokinetic pump with a housing having chambers separated by a flexible member, fluid flow, including high pressure fluids, is controlled by the application of an electric potential, that can vary with time.

Paul, Phillip H. (Livermore, CA); Rakestraw, David J. (Fremont, CA)

2000-01-01T23:59:59.000Z

440

Pressure sensor for sealed containers  

DOE Patents [OSTI]

A magnetic pressure sensor for sensing a pressure change inside a sealed container. The sensor includes a sealed deformable vessel having a first end attachable to an interior surface of the sealed container, and a second end. A magnet mounted to the vessel second end defining a distance away from the container surface provides an externally detectable magnetic field. A pressure change inside the sealed container causes deformation of the vessel changing the distance of the magnet away from the container surface, and thus the detectable intensity of the magnetic field.

Hodges, Franklin R. (Loudon, TN)

2001-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Flatness of heavy chain systems Nicolas Petit 1  

E-Print Network [OSTI]

.e. trolleys carrying a fixed length heavy chain that may carry a load, is addressed in the partial derivatives the homogeneous chain carrying a load, see equation (13). In [11] the flatness [3, 4] of heavy chain systems, i dimensional case. Under small angle approximations, these heavy chain systems are described by a 1D partial

442

Enrichment of Heavy Metals in Sediment Resulting from Soil  

E-Print Network [OSTI]

, Harpenden, Hertfordshire AL5 2JQ, U.K. Heavy metal pollution of soil and water is often associated of water erosion in detaching and transporting sediment-associated heavy metals from agri- cultural soils to surface waters has been overlooked. Heavy metals in arable soils are derived from the soil parent material

Quinton, John

443

Chemistry 330 / Study Guide 217 Toxic Heavy Metals  

E-Print Network [OSTI]

Chemistry 330 / Study Guide 217 Unit 7 Toxic Heavy Metals Overview In ancient Rome wine was stored. Metals--especially heavy metals--pose a unique environmental pollution problem. Heavy metals are especially toxic because their ions are water-soluble and readily taken up by the body. Once in the body

Short, Daniel

444

Permeable Reactive Biobarriers for the Containment of Heavy Metal  

E-Print Network [OSTI]

. Heavy metals are leached as ground water reaches the exposed ores. Arizona has a rich historyPermeable Reactive Biobarriers for the Containment of Heavy Metal Contamination in Acid Mine) is defined as the presence heavy metals, increased acidity, and sulfate as a direct result of mining

Fay, Noah

445

Tons of Heavy Metals in Mill Creek Sediments Heather Freeman  

E-Print Network [OSTI]

objectives for this summer research were to: 1.) determine how much heavy metal pollution has accumulatedTons of Heavy Metals in Mill Creek Sediments Heather Freeman 8/30/99 Geology Department Advisors: Dr. Kees DeJong Dr. Barry Manyard Dr. David Nash #12;Tons of heavy metals in Mill Creek sediments

Maynard, J. Barry

446

REVIEW ARTICLE Heavy Metal Pollutants and Chemical Ecology: Exploring  

E-Print Network [OSTI]

REVIEW ARTICLE Heavy Metal Pollutants and Chemical Ecology: Exploring New Frontiers Robert S. Boyd to be learned about how heavy metal pollution impacts organisms, and that exciting new research frontiers as pollutants (Han et al. 2002), including Cd, Cu, Cr, Hg, Pb, Ni, and Zn. Much research on heavy metal

Boyd, Robert S.

447

ECR plasma source for heavy ion beam charge neutralization  

E-Print Network [OSTI]

plasmas are being considered as a medium for charge neutralizing heavy ion beams in order to focus beyond resonance. Keywords: Plasma focus; RF plasma; Beam charge neutralization 1. INTRODUCTION A possible heavyECR plasma source for heavy ion beam charge neutralization PHILIP C. EFTHIMION,1 ERIK GILSON,1

Gilson, Erik

448

Vehicle and Heavy Equipment Integrated Product & Process Development (IPPD)  

E-Print Network [OSTI]

Vehicle and Heavy Equipment Integrated Product & Process Development (IPPD) Technology Development City, IA 52242 Beckermann, C., and Fischer, G.W., "Vehicle and Heavy Equipment Integrated Product, 1993. #12;Abstract An overview is presented of the recently proposed Vehicle and Heavy Equipment

Beckermann, Christoph

449

Gold Nanoparticle-Based Sensing of "Spectroscopically Silent" Heavy Metal  

E-Print Network [OSTI]

of aqueous heavy metal ions, including toxic metals such as lead, cadmium, and mercury, is describedLetters Gold Nanoparticle-Based Sensing of "Spectroscopically Silent" Heavy Metal Ions Youngjin Kim that by functionalizing metal nanoparticles with appropriate heavy-metal ion receptors, the particles might be coaxed

450

Pneumatic brake control for precision stopping of heavy-duty vehicles  

E-Print Network [OSTI]

6], heavy-duty vehicle maintenance automation, as well astrue” automation are applications on heavy-duty vehicles [

Bu, Fanping; Tan, Han-Shue

2007-01-01T23:59:59.000Z

451

Boron-10 Lined Proportional Counter Wall Effects  

SciTech Connect (OSTI)

The Department of Energy Office of Nuclear Safeguards (NA-241) is supporting the project 'Coincidence Counting With Boron-Based Alternative Neutron Detection Technology' at Pacific Northwest National Laboratory (PNNL) for development of an alternative neutron coincidence counter. The goal of this project is to design, build and demonstrate a boron-lined proportional tube based system in the configuration of a coincidence counter. This report provides information about how variations in proportional counter radius and gas pressure in a typical coincident counter design might affect the observed signal from boron-lined tubes. A discussion comparing tubes to parallel plate counters is also included.

Siciliano, Edward R.; Kouzes, Richard T.

2012-05-01T23:59:59.000Z

452

Theoretical comparison between field emission from single-wall and multi-wall carbon nanotubes A. Mayer,1,  

E-Print Network [OSTI]

Theoretical comparison between field emission from single-wall and multi-wall carbon nanotubes A s : 73.63.Fg, 79.70. q, 85.35.Kt, 03.65.Nk I. INTRODUCTION Carbon nanotubes show interesting field-emission of field emission from carbon nanotubes,13­16 we now consider the depen- dence of the emission from single

Mayer, Alexandre

453

The Relationships Between ELM Suppression, Pedestal Profiles, and Lithium Wall Coatings in NSTX  

SciTech Connect (OSTI)

Recently in the National Spherical Torus Experiment (NSTX), increasing lithium wall coatings suppressed edge localized modes (ELMs), gradually but not quite monotonically. This work details profile and stability analysis as ELMs disappeared throughout the lithium scan. While the quantity of lithium deposited between discharges did not uniquely determine the presence of ELMs, profile analysis demonstrated that lithium was correlated to wider density and pressure pedestals with peak gradients farther from the separatrix. Moreover, the ELMy and ELM-free discharges were cleanly separated by their density and pedestal widths and peak gradient locations. Ultimately, ELMs were only suppressed when lithium caused the density pedestal to widen and shift inward. These changes in the density gradient were directly reflected in the pressure gradient and calculated bootstrap current. This supports the theory that ELMs in NSTX are caused by peeling and/or ballooning modes, as kink/peeling modes are stabilized when the edge current and pressure gradient shift away from the separatrix. Edge stability analysis using ELITE corroborated this picture, as reconstructed equilibria from ELM-free discharges were generally farther from their kink/peeling stability boundaries than ELMy discharges. We conclude that density profile control provided by lithium is the key first step to ELM suppression in NSTX

D.P. Boyle, R. Maingi, P.B. Snyder, J. Manickam, T.H. Osborne, R.E. Bell, B.P. LeBlanc, and the NSTX Team

2012-08-17T23:59:59.000Z

454

Development of Designer Diamond Technology for High Pressure High Temperature Experiments in Support of Stockpile Stewardship Program  

SciTech Connect (OSTI)

The role of nitrogen in the fabrication of designer diamond was systematically investigated by adding controlled amount of nitrogen in hydrogen/methane/oxygen plasma. This has led to a successful recipe for reproducible fabrication of designer diamond anvils for high-pressure high-temperature research in support of stockpile stewardship program. In the three-year support period, several designer diamonds fabricated with this new growth chemistry were utilized in high-pressure experiments at UAB and Lawrence Livermore National Laboratory. The designer diamond anvils were utilized in high-pressure studies on heavy rare earth metals, high pressure melting studies on metals, and electrical resistance measurements on iron-based layered superconductors under high pressures. The growth chemistry developed under NNSA support can be adapted for commercial production of designer diamonds.

Vohra, Yogesh, K.

2009-10-28T23:59:59.000Z

455

Heavy-Section Steel Technology Program: Recent developments in crack initiation and arrest research  

SciTech Connect (OSTI)

Technology for the analysis of crack initiation and arrest is central to the reactor pressure vessel fracture-margin-assessment process. Regulatory procedures for nuclear plants utilize this technology to assure the retention of adequate fracture-prevention margins throughout the plant operating license period. As nuclear plants age and regulatory procedures dictate that fracture-margin assessments be performed, interest in the fracture-mechanics technology incorporated into those procedures has heightened. This has led to proposals from a number of sources for development and refinement of the underlying crack-initiation and arrest-analysis technology. This paper presents an overview of ongoing Heavy-Section Steel Technology (HSST) Program research aimed at refining the fracture toughness data used in the analysis of fracture margins under pressurized-thermal-shock loading conditions. 33 refs., 13 figs.

Pennell, W.E.

1991-01-01T23:59:59.000Z

456

Electrokinetic high pressure hydraulic system  

DOE Patents [OSTI]

An electrokinetic high pressure hydraulic pump for manipulating fluids in capillary-based system. The pump uses electro-osmotic flow to provide a high pressure hydraulic system, having no moving mechanical parts, for pumping and/or compressing fluids, for providing valve means and means for opening and closing valves, for controlling fluid flow rate, and manipulating fluid flow generally and in capillary-based systems (microsystems), in particular. The compact nature of the inventive high pressure hydraulic pump provides the ability to construct a micro-scale or capillary-based HPLC system that fulfills the desire for small sample quantity, low solvent consumption, improved efficiency, the ability to run samples in parallel, and field portability. Control of pressure and solvent flow rate is achieved by controlling the voltage applied to an electrokinetic pump.

Paul, Phillip H.; Rakestraw, David J.; Arnold, Don W.; Hencken, Kenneth R.; Schoeniger, Joseph S.; Neyer, David W.

2003-06-03T23:59:59.000Z

457

Electrokinetic high pressure hydraulic system  

DOE Patents [OSTI]

An electrokinetic high pressure hydraulic pump for manipulating fluids in capillary-based systems. The pump uses electro-osmotic flow to provide a high pressure hydraulic system, having no moving mechanical parts, for pumping and/or compressing fluids, for providing valve means and means for opening and closing valves, for controlling fluid flow rate, and manipulating fluid flow generally and in capillary-based systems (Microsystems), in particular. The compact nature of the inventive high pressure hydraulic pump provides the ability to construct a micro-scale or capillary-based HPLC system that fulfills the desire for small sample quantity, low solvent consumption, improved efficiency, the ability to run samples in parallel, and field portability. Control of pressure and solvent flow rate is achieved by controlling the voltage applied to an electrokinetic pump.

Paul, Phillip H. (Livermore, CA); Rakestraw, David J. (Fremont, CA); Arnold, Don W. (Livermore, CA); Hencken, Kenneth R. (Pleasanton, CA); Schoeniger, Joseph S. (Oakland, CA); Neyer, David W. (Castro Valley, CA)

2001-01-01T23:59:59.000Z

458

Pressure compensated flow control valve  

DOE Patents [OSTI]

The invention is an air flow control valve which is capable of maintaining a constant flow at the outlet despite changes in the inlet or outlet pressure. The device consists of a shell assembly with an inlet chamber and outlet chamber separated by a separation plate. The chambers are connected by an orifice. Also located within the inlet chamber is a port controller assembly. The port controller assembly consists of a differential pressure plate and port cap affixed thereon. The cap is able to slide in and out of the orifice separating the inlet and outlet chambers. When the pressure differential is sufficient, the differential pressure plate rises or falls to maintain a constant air flow. Movement of the port controller assembly does not require the use of seals, diaphragms, tight tolerances, bushings, bearings, hinges, guides, or lubricants.

Minteer, Daniel J. (West Richland, WA)

1999-01-01T23:59:59.000Z

459

Low pressure carbonylation of heterocycles  

DOE Patents [OSTI]

Heterocycles, e.g., epoxides, are carbonylated at low pressure with high percentage conversion to cyclic, ring expanded products using the catalyst ##STR00001## where L is tetrahydrofuran (THF).

Coates, Geoffrey W. (Lansing, NY); Kramer, John W. (Mt. Pleasant, MI); Schmidt, Joseph A. R. (Sylvania, OH)

2011-01-25T23:59:59.000Z

460

Domain wall QCD with physical quark masses  

E-Print Network [OSTI]

We present results for several light hadronic quantities ($f_\\pi$, $f_K$, $B_K$, $m_{ud}$, $m_s$, $t_0^{1/2}$, $w_0$) obtained from simulations of 2+1 flavor domain wall lattice QCD with large physical volumes and nearly-physical pion masses at two lattice spacings. We perform a short, O(3)%, extrapolation in pion mass to the physical values by combining our new data in a simultaneous chiral/continuum `global fit' with a number of other ensembles with heavier pion masses. We use the physical values of $m_\\pi$, $m_K$ and $m_\\Omega$ to determine the two quark masses and the scale - all other quantities are outputs from our simulations. We obtain results with sub-percent statistical errors and negligible chiral and finite-volume systematics for these light hadronic quantities, including: $f_\\pi$ = 130.2(9) MeV; $f_K$ = 155.5(8) MeV; the average up/down quark mass and strange quark mass in the $\\overline {\\rm MS}$ scheme at 3 GeV, 2.997(49) and 81.64(1.17) MeV respectively; and the neutral kaon mixing parameter, $B_K$, in the RGI scheme, 0.750(15) and the $\\overline{\\rm MS}$ scheme at 3 GeV, 0.530(11).

RBC; UKQCD collaborations; :; T. Blum; P. A. Boyle; N. H. Christ; J. Frison; N. Garron; R. J. Hudspith; T. Izubuchi; T. Janowski; C. Jung; A. Juettner; C. Kelly; R. D. Kenway; C. Lehner; M. Marinkovic; R. D. Mawhinney; G. McGlynn; D. J. Murphy; S. Ohta; A. Portelli; C. T. Sachrajda; A. Soni

2014-11-25T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Pneumatic wall-locking geophone system  

DOE Patents [OSTI]

A seismic signal receiving system is provided for use in boreholes to receive seismic waves in carrying out geophysical investigations. The system includes three pairs of opposed plates, each of the pairs of plates including oppositely facing outer surfaces for engagement with opposite sides of a borehole. A seismic receiver is mounted on the inner surface of each of the plates for receiving seismic signals. A double-acting, fluid-operated actuator selectively causes relative movement of the plates of the pairs of plates away from each other to provide expansion thereof so as to enable the plates to engage the walls of a borehole and selectively causes relative movement of the plates of the pairs of plates toward each other to provide retraction thereof so as to enable the system to be removed from a borehole. The pairs of plates each comprise a relatively long plate and a relatively short plate. An expandable linkage interconnects the long plates at the distal ends thereof. The plates are mechanically biassed into the retracted state so that the plates return to this state in the event of a system failure.

Kuhlman, Harland L. (Minneapolis, MN); Cumerlato, Calvin L. (Minneapolis, MN); Tweeton, Daryl R. (Apple Valley, MN)

1991-01-01T23:59:59.000Z

462

Bitumen pressure cell installation and monitoring procedure: Draft  

SciTech Connect (OSTI)

A 6-in. (150-mm)-thick bitumen layer will be placed between the upper shaft preliminary concrete lining and the steel lining component of the final lining. The function of this layer is twofold; first, it will act as a compliant sealing layer which, because of the bitumen's fluid properties, will remain effective even if the concrete and steel lining components suffer significant strains; and second, it will help to ensure a uniform transmission of rock or hydrostatic loads to the inner lining components. A type 200--300 penetration grade bitumen (ASTM D946) will be used, with 32% by weight of added limestone flour. The purpose of the limestone flour is to ensure that the bitumen has a density which is greater than that of the formation fluids, resulting in a positive pressure gradient from the bitumen to the ground water. The resulting mixture will have a specific gravity of about 1.25 at 60/degree/F (15/degree/C). Pressure measurements in the bitumen layer are needed in order to determine loads on the inner lining components. Although some initial loading will occur in response to excavation, full rock and hydrostatic loads will not develop until post-construction thawing of the freeze wall is complete. Loads transmitted by the bitumen layer to the other lining components will be those which act radially, i.e., the bitustatic pressure, or the radial stress if deviatoric stresses develop.

Not Available

1987-02-01T23:59:59.000Z

463

The Unique High-Pressure Behavior of Curium Probed Further Using Alloys  

SciTech Connect (OSTI)

The changing role of the 5f electrons across the actinide series has been of prime interest for many years. The remarkable behavior of americium's 5f electrons under pressure was determined experimentally a few years ago and it precipitated a strong interest in the heavy element community. Theoretical treatments of americium's behavior under pressure followed and continue today. Experimental and theoretical findings regarding curium's behavior under pressure have shown that the pressure behavior of curium was not a mirror image of that for americium. Rather, one of the five crystallographic phases observed with curium (versus four for americium) was a unique monoclinic structure whose existence is due to a spin stabilization effect by curium's 5f{sup 7} electronic configuration and its half-filled 5f-shell. We review briefly the behavior of pure curium under pressure but focus on the pressure behaviors of three curium alloys with the intent of comparing them with pure curium. An important experimental finding confirmed by theoretical computations, is that dilution of curium with its near neighbors is sufficient to prevent the formation of the unique C2/c phase that appears in pure Cm metal under pressure. As this unique C2/c phase is very sensitive to having a 5f{sup 7} configuration to maximize the magnetic spin polarization, dilution of this state with adjacent actinide neighbors reduces its stability.

Heathman, S. [European Commission Joint Research Centre; Haire, Richard {Dick} G [ORNL; LeBihan, T. [CEA-Centre de Valduc, Is-sur-Tille, France; Ahuja, R. [Uppsala University, Uppsala, Sweden; Li, S. [Virginia Commonwealth University, Richland; Luo, W. [Uppsala University, Uppsala, Sweden; Johansson, B. [Royal Institute of Technology, Stockholm, Sweden

2007-01-01T23:59:59.000Z

464

A Computer Program for Simulating Transient Behavior in Steam Turbine Stage Pressure of AHWR  

SciTech Connect (OSTI)

It is proposed to couple the Advanced Heavy water reactor (AHWR), which is being developed by Bhabha Atomic Research Centre, India, with a desalination plant. The objective of this coupling is to produce system make-up and domestic water. The proposed desalination plant needs about 1.9 kg/sec of steam and the minimum pressure requirement is 3 bars. The desalination plant can be fed with bled steam extracted from a suitable stage in low pressure turbine. As the turbine stage pressure changes with the load, it is essential to know the availability of bled steam at aforesaid pressure for various load condition. The objective of the present study is to identify a suitable extraction point so as to ensure availability of steam at desired condition for desalination plant, even at part load conditions. In order to fulfill the above objective a steam and feed system analysis code was developed which incorporates the mathematical formulation of different components of the steam and feed system such as, high pressure (HP) and low pressure (LP) turbines, re-heater, feed heaters etc. The dynamic equations are solved simultaneously to obtain the stage pressure at various load conditions. Based on the results obtained, the suitable extraction stage in LP turbine was selected. This enables to determine the lowest possible part load operation up to which availability of desalination plant could be ensured. (authors)

Dutta, Anu; Thangamani, I.; Chakraborty, G.; Ghosh, A.K.; Kushwaha, H.S. [Bhabha Atomic Research Centre, Trombay, Mumbai - 400 085 (India)

2006-07-01T23:59:59.000Z

465

Deployment Scenario of Heavy Water Cooled Thorium Breeder Reactor  

SciTech Connect (OSTI)

Deployment scenario of heavy water cooled thorium breeder reactor has been studied. We have assumed to use plutonium and thorium oxide fuel in water cooled reactor to produce {sup 233}U which will be used in thorium breeder reactor. The objective is to analysis the potential of water cooled Th-Pu reactor for replacing all of current LWRs especially in Japan. In this paper, the standard Pressurize Water Reactor (PWR) has been designed to produce 3423 MWt; (i) Th-Pu PWR, (ii) Th-Pu HWR (MFR = 1.0) and (iii) Th-Pu HWR (MFR 1.2). The properties and performance of the core were investigated by using cell and core calculation code. Th-Pu PWR or HWR produces {sup 233}U to introduce thorium breeder reactor. The result showed that to replace all (60 GWe) LWR by thorium breeder reactor within a period of one century, Th-Pu oxide fueled PWR has insufficient capability to produce necessary amount of {sup 233}U and Th-Pu oxide fueled HWR has almost enough potential to produce {sup 233}U but shows positive void reactivity coefficient.

Mardiansah, Deby; Takaki, Naoyuki [Course of Applied Science, School of Engineering, Tokai University (Japan)

2010-06-22T23:59:59.000Z

466

Langevin dynamics and decoherence of heavy quarks at high temperatures  

E-Print Network [OSTI]

Langevin equation of heavy quarks in high-temperature quark-gluon plasma is derived. The dynamics of heavy quark color is coupled with the phase space dynamics and causes a macroscopic superposition state of heavy quark momentum. Decoherence of the superposition state allows us classical description. The time scale of decoherence gives an appropriate discretization time scale $\\Delta t \\sim \\sqrt{M/\\gamma}$ for the classical Langevin equation, where $M$ is heavy quark mass and $\\gamma$ is heavy quark momentum diffusion constant.

Akamatsu, Yukinao

2015-01-01T23:59:59.000Z

467

Double wall vacuum tubing and method of manufacture  

DOE Patents [OSTI]

An evacuated double wall tubing is shown together with a method for the manufacture of such tubing which includes providing a first pipe of predetermined larger diameter and a second pipe having an O.D. substantially smaller than the I.D. of the first pipe. An evacuation opening is then in the first pipe. The second pipe is inserted inside the first pipe with an annular space therebetween. The pipes are welded together at one end. A stretching tool is secured to the other end of the second pipe after welding. The second pipe is then prestressed mechanically with the stretching tool an amount sufficient to prevent substantial buckling of the second pipe under normal operating conditions of the double wall pipe. The other ends of the first pipe and the prestressed second pipe are welded together, preferably by explosion welding, without the introduction of mechanical spacers between the pipes. The annulus between the pipes is evacuated through the evacuation opening, and the evacuation opening is finally sealed. The first pipe is preferably of steel and the second pipe is preferably of titanium. The pipes may be of a size and wall thickness sufficient for the double wall pipe to be structurally load bearing or may be of a size and wall thickness insufficient for the double wall pipe to be structurally load bearing, and the double wall pipe positioned with a sliding fit inside a third pipe of a load-bearing size.

Stahl, Charles R. (Scotia, NY); Gibson, Michael A. (Houston, TX); Knudsen, Christian W. (Houston, TX)

1989-01-01T23:59:59.000Z

468

Spray bottle apparatus with pressure multiplying pistons  

DOE Patents [OSTI]

The present invention comprises a spray bottle in which the pressure resulting from the gripping force applied by the user is amplified and this increased pressure used in generating a spray such as an aerosol or fluid stream. In its preferred embodiment, the invention includes a high pressure chamber and a corresponding piston which is operative for driving fluid out of this chamber at high pressure through a spray nozzle and a low pressure chamber and a corresponding piston which is acted upon the hydraulic pressure within the bottle resulting from the gripping force. The low pressure chamber and piston are of larger size than the high pressure chamber and piston. The pistons are rigidly connected so that the force created by the pressure acting on the piston in the low pressure chamber is transmitted to the piston in the high pressure chamber where it is applied over a more limited area thereby generating greater hydraulic pressure for use in forming the spray.

Moss, Owen R. (Kennewick, WA); Gordon, Norman R. (Kennewick, WA); DeFord, Henry S. (Kennewick, WA)

1990-01-01T23:59:59.000Z

469

Endografts, Pressure, and the Abdominal Aortic Aneurysm  

E-Print Network [OSTI]

surveillance protocols [28]. The relationship between peripheral arterial pressure and aortic pulse pressure was shown to be an underestimation of the pulse pressure within the abdominal aorta by a mean of 10% with a sphygmomanometer which was similar to a...

Meyer, Clark A.

2010-07-14T23:59:59.000Z

470

Conductance-Controlled Point Functionalization of Single-Walled Carbon Nanotubes  

E-Print Network [OSTI]

of Single-Walled Carbon Nanotubes Brett R. Goldsmith, 1 Johnof Single-Walled Carbon Nanotubes Brett R. Goldsmith et al.single-walled carbon nanotubes (SWNTs) to fabricate single-

Collins, Philip G

2007-01-01T23:59:59.000Z

471

A High Resolution Ultrawideband Wall Penetrating Erman Engin, Berkehan iftiolu, Meri zcan and brahim Tekin  

E-Print Network [OSTI]

for underground mine detection [1], [2], through the wall imaging [3], cancerous tissue detection applications [4 respiratory activity of a human behind a 23 cm thick brick wall. Keywords: UWB Radar, Wall penetrating Radar

Yanikoglu, Berrin

472

Thermophysical properties of saturated light and heavy water for advanced neutron source applications  

SciTech Connect (OSTI)

The Advanced Neutron Source is an experimental facility being developed by Oak Ridge National Laboratory. As a new nuclear fission research reactor of unprecedented flux, the Advanced Neutron Source Reactor will provide the most intense steady-state beams of neutrons in the world. The high heat fluxes generated in the reactor [303 MW(t) with an average power density of 4.5 MW/L] will be accommodated by a flow of heavy water through the core at high velocities. In support of this experimental and analytical effort, a reliable, highly accurate, and uniform source of thermodynamic and transport property correlations for saturated light and heavy water were developed. In order to attain high accuracy in the correlations, the range of these correlations was limited to the proposed Advanced Neutron Source Reactor's nominal operating conditions. The temperature and corresponding saturation pressure ranges used for light water were 20--300[degrees]C and 0.0025--8.5 MPa, respectively, while those for heavy water were 50--250[degrees]C and 0.012--3.9 MPa. Deviations between the correlation predictions and data from the various sources did not exceed 1.0%. Light water vapor density was the only exception, with an error of 1.76%. The physical property package consists of analytical correlations, SAS codes, and FORTRAN subroutines incorporating these correlations, as well as an interactive, easy-to-use program entitled QuikProp.

Crabtree, A.; Siman-Tov, M.

1993-05-01T23:59:59.000Z

473

Thermophysical properties of saturated light and heavy water for Advanced Neutron Source applications  

SciTech Connect (OSTI)

The Advanced Neutron Source is an experimental facility being developed by Oak Ridge National Laboratory. As a new nuclear fission research reactor of unprecedented flux, the Advanced Neutron Source Reactor will provide the most intense steady-state beams of neutrons in the world. The high heat fluxes generated in the reactor [303 MW(t) with an average power density of 4.5 MW/L] will be accommodated by a flow of heavy water through the core at high velocities. In support of this experimental and analytical effort, a reliable, highly accurate, and uniform source of thermodynamic and transport property correlations for saturated light and heavy water were developed. In order to attain high accuracy in the correlations, the range of these correlations was limited to the proposed Advanced Neutron Source Reactor`s nominal operating conditions. The temperature and corresponding saturation pressure ranges used for light water were 20--300{degrees}C and 0.0025--8.5 MPa, respectively, while those for heavy water were 50--250{degrees}C and 0.012--3.9 MPa. Deviations between the correlation predictions and data from the various sources did not exceed 1.0%. Light water vapor density was the only exception, with an error of 1.76%. The physical property package consists of analytical correlations, SAS codes, and FORTRAN subroutines incorporating these correlations, as well as an interactive, easy-to-use program entitled QuikProp.

Crabtree, A.; Siman-Tov, M.

1993-05-01T23:59:59.000Z

474

ICRF Specific Plasma Wall Interactions in JET with the ITER-Like Wall  

SciTech Connect (OSTI)

A variety of plasma wall interactions (PWIs) during operation of the so-called A2 ICRF antennas is observed in JET with the ITER-like wall. Amongst effects of the PWIs, the W content increase is the most significant, especially at low plasma densities. No increase of W source from the main divertor and entrance of the outer divertor during ICRF compared to NBI phases was found by means of spectroscopic and WI (400.9 nm) imaging diagnostics. In contrary, the W flux there is higher during NBI. Charge exchange neutrals of hydrogen isotopes could be excluded as considerable contributors to the W source. The high W content in ICRF heated limiter discharges suggests the possibility of other W sources than the divertor alone. Dependencies of PWIs to individual ICRF antennas during q95-scans, and intensification of those for the 90 phasing, indicate a link between the PWIs and the antenna near-fields. The PWIs include heat loads and Be sputtering pattern on antenna limiters. Indications of some PWIs at the outer divertor entrance are observed which do not result in higher W flux compared to the NBI phases, but are characterized by small antenna-specific (up to 25% with respect to ohmic phases) bipolar variations of WI emission. The first TOPICA calculations show a particularity of the A2 antennas compared to the ITER antenna, due to the presence of long antenna limiters in the RF image current loop and thus high near-fields across the most part of the JET outer wall.

Bobkov, V. [Max-Planck-Institut fur Plasmaphysik, EURATOM Association, Garching, Germany] [Max-Planck-Institut fur Plasmaphysik, EURATOM Association, Garching, Germany; Arnoux, G. [EURATOM, Culham Sci Ctr, Abingdon, Oxon England] [EURATOM, Culham Sci Ctr, Abingdon, Oxon England; Brezinsek, S. [Forschungszentrum Julich, Julich, Germany] [Forschungszentrum Julich, Julich, Germany; Coenen, J. W. [Institute of Energy and Climate Research, Germany] [Institute of Energy and Climate Research, Germany; Colas, L. [French Atomic Energy Commission (CEA)] [French Atomic Energy Commission (CEA); Clever, M. [Institute of Energy and Climate Research, Germany] [Institute of Energy and Climate Research, Germany; Czarnecka, A. [Association EURATOM-IPPLM, Warsaw, Poland] [Association EURATOM-IPPLM, Warsaw, Poland; Braun, F. [Max-Planck-Institut fur Plasma Physik, Garching, Germany] [Max-Planck-Institut fur Plasma Physik, Garching, Germany; Dux, R. [Max-Planck-Institut fur Plasma Physik, Garching, Germany] [Max-Planck-Institut fur Plasma Physik, Garching, Germany; Huber, Alexander [EURATOM / FZ-Juelich, Germany] [EURATOM / FZ-Juelich, Germany; Jacquet, P. [EURATOM / UKAEA, Abingdon, UK] [EURATOM / UKAEA, Abingdon, UK; Klepper, C Christopher [ORNL] [ORNL; Lerche, E. [ERM-KMS, Association EURATOM-Belgian State, Brussels, Belgium] [ERM-KMS, Association EURATOM-Belgian State, Brussels, Belgium; Maggi, C. [Max-Planck-Institut fur Plasma Physik, Garching, Germany] [Max-Planck-Institut fur Plasma Physik, Garching, Germany; Marcotte, F. [CEA IRFM, St. Paul-lez-Durance, France] [CEA IRFM, St. Paul-lez-Durance, France; Maslov, M. [Association EURATOM-CCFE, Abingdon, UK] [Association EURATOM-CCFE, Abingdon, UK; Matthews, G. [Association EURATOM-CCFE, Abingdon, UK] [Association EURATOM-CCFE, Abingdon, UK; Mayoral, M.-L. [EURATOM / UKAEA, UK] [EURATOM / UKAEA, UK; McCormick, K. D. [Max-Planck-Institut fur Plasma Physik, Garching, Germany] [Max-Planck-Institut fur Plasma Physik, Garching, Germany; Meigs, A. G. [EURATOM / UKAEA, UK] [EURATOM / UKAEA, UK; Milanesio, D. [Politecnico di Torino] [Politecnico di Torino; Monakhov, I. [EURATOM / UKAEA, Abingdon, UK] [EURATOM / UKAEA, Abingdon, UK; Neu, Rudolf [EURATOM / IPP Garching, Germany] [EURATOM / IPP Garching, Germany; Noterdaeme, J.-M. [Max-Planck-Institut fur Plasma Physik, Garching, Germany] [Max-Planck-Institut fur Plasma Physik, Garching, Germany; Putterich, Th. [Max-Planck-Institut fur Plasma Physik, Garching, Germany] [Max-Planck-Institut fur Plasma Physik, Garching, Germany; Rimini, F. [Association EURATOM-CCFE, Abingdon, UK] [Association EURATOM-CCFE, Abingdon, UK; Rooj, G. Van [Institute for Plasma Physics Rijnhuizen, Nieuwegein, Netherlands] [Institute for Plasma Physics Rijnhuizen, Nieuwegein, Netherlands; Sergienko, G. [Institute of Energy and Climate Research, Germany] [Institute of Energy and Climate Research, Germany; Van Eester, D. [ERM-KMS, Association EURATOM-Belgian State, Brussels, Belgium] [ERM-KMS, Association EURATOM-Belgian State, Brussels, Belgium

2013-01-01T23:59:59.000Z

475

Transformation of Resources to Reserves: Next Generation Heavy-Oil Recovery Techniques  

SciTech Connect (OSTI)

This final report and technical progress report describes work performed from October 1, 2004 through September 30, 2007 for the project 'Transformation of Resources to Reserves: Next Generation Heavy Oil Recovery Techniques', DE-FC26-04NT15526. Critical year 3 activities of this project were not undertaken because of reduced funding to the DOE Oil Program despite timely submission of a continuation package and progress on year 1 and 2 subtasks. A small amount of carried-over funds were used during June-August 2007 to complete some work in the area of foamed-gas mobility control. Completion of Year 3 activities and tasks would have led to a more thorough completion of the project and attainment of project goals. This progress report serves as a summary of activities and accomplishments for years 1 and 2. Experiments, theory development, and numerical modeling were employed to elucidate heavy-oil production mechanisms that provide the technical foundations for producing efficiently the abundant, discovered heavy-oil resources of the U.S. that are not accessible with current technology and recovery techniques. Work fell into two task areas: cold production of heavy oils and thermal recovery. Despite the emerging critical importance of the waterflooding of viscous oil in cold environments, work in this area was never sanctioned under this project. It is envisioned that heavy oil production is impacted by development of an understanding of the reservoir and reservoir fluid conditions leading to so-called foamy oil behavior, i.e, heavy-oil solution gas drive. This understanding should allow primary, cold production of heavy and viscous oils to be optimized. Accordingly, we evaluated the oil-phase chemistry of crude oil samples from Venezuela that give effective production by the heavy-oil solution gas drive mechanism. Laboratory-scale experiments show that recovery correlates with asphaltene contents as well as the so-called acid number (AN) and base number (BN) of the crude oil. A significant number of laboratory-scale tests were made to evaluate the solution gas drive potential of West Sak (AK) viscous oil. The West Sak sample has a low acid number, low asphaltene content, and does not appear foamy under laboratory conditions. Tests show primary recovery of about 22% of the original oil in place under a variety of conditions. The acid number of other Alaskan North Slope samples tests is greater, indicating a greater potential for recovery by heavy-oil solution gas drive. Effective cold production leads to reservoir pressure depletion that eases the implementation of thermal recovery processes. When viewed from a reservoir perspective, thermal recovery is the enhanced recovery method of choice for viscous and heavy oils because of the significant viscosity reduction that accompanies the heating of oil. One significant issue accompanying thermal recovery in cold environments is wellbore heat losses. Initial work on thermal recovery found that a technology base for delivering steam, other hot fluids, and electrical heat through cold subsurface environments, such as permafrost, was in place. No commercially available technologies are available, however. Nevertheless, the enabling technology of superinsulated wells appears to be realized. Thermal subtasks focused on a suite of enhanced recovery options tailored to various reservoir conditions. Generally, electrothermal, conventional steam-based, and thermal gravity drainage enhanced oil recovery techniques appear to be applicable to 'prime' Ugnu reservoir conditions to the extent that reservoir architecture and fluid conditions are modeled faithfully here. The extent of reservoir layering, vertical communication, and subsurface steam distribution are important factors affecting recovery. Distribution of steam throughout reservoir volume is a significant issue facing thermal recovery. Various activities addressed aspects of steam emplacement. Notably, hydraulic fracturing of horizontal steam injection wells and implementation of steam trap control that limits steam entry into hor

Stanford University; Department of Energy Resources Engineering Green Earth Sciences

2007-09-30T23:59:59.000Z

476

Plant rhamnogalacturonan II complexation of heavy metal cations  

DOE Patents [OSTI]

The present invention provides rhamnogalacturonan-II (RG-II) and relates to its ability to complex specific multivalent heavy metal cations. In the presence of boric acid, RG-II monomers form dimers that are cross-linked by a borate ester. The yield of such borate ester cross-linked dimers of RG-II is enhanced in the presence of specific heavy metal cations. The present invention further relates to the utility of RG-II in assays for the detection of specific heavy metal contamination; as a reagent useful in the removal of specific heavy metal cations contaminating foods and liquids, for example, fish, wines, etc.; as a pharmaceutical composition useful as an antidote in specific heavy metal cation poisoning; as a treatment for the detoxification of specific heavy metal cations from blood and/or tissues; and in a method of remediation of waters and soils contaminated with specific heavy metal cations.

O'Neill, Malcolm A. (Winterville, GA); Pellerin, Patrice J. M. (Montpellier, FR); Warrenfeltz, Dennis (Athens, GA); Vidal, Stephane (Combaillaux, FR); Darvill, Alan G. (Athens, GA); Albersheim, Peter (Athens, GA)

1999-01-01T23:59:59.000Z

477

Plant rhamnogalacturonan II complexation of heavy metal cations  

DOE Patents [OSTI]

The present invention provides rhamnogalacturonan-II (RG-II) and relates to its ability to complex specific multivalent heavy metal cations. In the presence of boric acid, RG-II monomers form dimers that are cross-linked by a borate ester. The yield of such borate ester cross-linked dimers of RG-II is enhanced in the presence of specific heavy metal cations. The present invention further relates to the utility of RG-II in assays for the detection of specific heavy metal contamination; as a reagent useful in the removal of specific heavy metal cations contaminating foods and liquids, for example, fish, wines, etc.; as a pharmaceutical composition useful as an antidote in specific heavy metal cation poisoning; as a treatment for the detoxification of specific heavy metal cations from blood and/or tissues; and in a method of remediation of waters and soils contaminated with specific heavy metal cations. 15 figs.

O`Neill, M.A.; Pellerin, P.J.M.; Warrenfeltz, D.; Vidal, S.; Darvill, A.G.; Albersheim, P.

1999-03-02T23:59:59.000Z

478

Crystalline mesoporous zirconia catalysts having stable tetragonal pore wall structure  

DOE Patents [OSTI]

Methods for the preparation of new sulfated mesoporous zirconia materials/catalysts with crystalline pore walls of predominantly tetragonal crystal structure, characterized by nitrogen physisorption measurement, X-ray diffraction, transmission electron microscopy and catalytic tests using n-butane isomerization to iso-butane and alkylation of 1-naphthol with 4-tert-butylstyrene as probe reactions. Sulfate deposition is preferred for the transformation of a mesoporous precursor with amorphous pore walls into a material with crystalline pore walls maintaining the mesoporous characteristics.

Sachtler, Wolfgang M. H. (Evanston, IL); Huang, Yin-Yan (Evanston, IL)

1998-01-01T23:59:59.000Z

479

Crystalline mesoporous zirconia catalysts having stable tetragonal pore wall structure  

DOE Patents [OSTI]

Methods are disclosed for the preparation of new sulfated mesoporous zirconia materials/catalysts with crystalline pore walls of predominantly tetragonal crystal structure, characterized by nitrogen physical sorption measurement, X-ray diffraction, transmission electron microscopy and catalytic tests using n-butane isomerization to iso-butane and alkylation of 1-naphthol with 4-tert-butylstyrene as probe reactions. Sulfate deposition is preferred for the transformation of a mesoporous precursor with amorphous pore walls into a material with crystalline pore walls maintaining the mesoporous characteristics. 17 figs.

Sachtler, W.M.H.; Huang, Y.Y.

1998-07-28T23:59:59.000Z

480

SUBCRITICAL BUBBLES NEAR THE PHASE SPACE DOMAIN WALL  

E-Print Network [OSTI]

We study the subcritical bubble formation near the phase space domain wall. We take into account that the phase of the scalar field can vary using complex U(1) symmetric field and a phenomenological potential with cubic term responsible to symmetry breaking. We show that the presence of the domain wall induces subcritical bubbles so that their formation rate near the wall is considerably larger than far of it. The allowed deviations of the phases of new bubbles are so large that they prevent the system from induced nucleation.

J. Sirkka; I. Vilja

1995-03-31T23:59:59.000Z

Note: This page contains sample records for the topic "heavy walled pressure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Flexible Pressure Sensors: Modeling and Experimental Characterization  

E-Print Network [OSTI]

Flexible capacitive pressure sensors fabricated with nanocomposites were experimentally characterized and results compared with simulations from analytical modeling. Unlike traditional diaphragm silicon pressure sensors, ...

Viana, J.C.

482

Documentation Requirements for Pressurized Experiment Equipment  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Documentation Requirements for Pressurized Experiment Apparatus PSSC NOTE01 15-Jan-2013 When bringing a piece of apparatus to the APS for an experiment that will involve pressure,...

483

ADS/CFT Applied To Vector Meson Emission From A Heavy Accelerated Nucleus  

E-Print Network [OSTI]

We consider a classical source, moving on the 4-D boundary of a 5-D ADS space, that is coupled to quantum fields residing in the bulk. Bremsstrahlung-like radiation of the corresponding quanta is shown to occur and the S-matrix is derived assuming that the source is sufficiently massive so that recoil effects are negligible. As an illustrative example, using the ADS hard-wall model, we consider vector mesons coupled to a heavy nucleus that is moved around at high speed in an accelerator ring. The meson radiation rate is found to be finite but small. Much higher accelerations, such as when a pair of heavy ions suffer an ultra peripheral collision, cause substantial emission of various excited vector mesons. Predictions are made for the spectrum of this radiation. A comparison is made against existing photon-pomeron fusion calculations for the transverse momentum spectra of rho mesons. These have the same overall shape as the recently measured transverse momentum distributions at RHIC.

Pervez Hoodbhoy

2008-09-11T23:59:59.000Z

484

Automatic reactor power control for a pressurized water reactor  

SciTech Connect (OSTI)

An automatic reactor power control system is presented for a pressurized water reactor (PWR). The associated reactor control strategy is called mode K.' The new system implements a heavy-worth bank dedicated to axial shape control, independent of the existing regulating banks. The heavy bank provides a monotonic relationship between its motion and the axial shape change, which allows automatic control of the axial power distribution. Thus, the mode K enables precise regulation of both the reactivity and the power distribution, by using double closed-loop control of the reactor coolant temperature and the axial power difference. Automatic reactor power control permits the nuclear power plant to accommodate the load-follow operations, including frequency control, to respond to the grid requirements. The mode K reactor control concepts were tested using simulation responses of a Korean standardized 1,000-MW (electric) PWR. The simulation results illustrate that the mode K would be a practical reactor power control strategy for the increased automation of nuclear plants.

Jungin Choi (Kyungwon Univ. (Korea, Republic of)); Yungjoon Hah (Korea Atomic Energy Research Inst., Daejeon (Korea, Republic of)); Unchul Lee (Seoul National Univ. (Korea, Republic of))

1993-05-01T23:59:59.000Z

485

Evaluation of discontinuity stresses in thick walled cylindrical shells by means of an embedded polariscope  

E-Print Network [OSTI]

Q M r Figure 3. Sign Convention for Levy's Method. After manipulation of basic equations combined with the forces on an element in the wall, Levy arrives at the basic differential equation ? + 4S w = d4 (I ? v) d2 D dx dx (2-13) 2 = ~ + 8 5W 8...;TINUI TY STRESSES Ii~' CY' INDR ICAL SHELLS /ppiF:x Cp 44l-, ? ? ? - ?; /'; 25 X p? QH INTER, 9 4 CL PRESSURE = pF5 0 pi 2 X, 3HPSI p27X p 17HUVERAf L LCNGT!' -- . F6:. 3p 2Xp C6H4 NC HE S p / . . 21X p 95H- C /} 53 FGRYAT f 2 8x p? 3HINS ICE !i...

Cano, Narciso Ortiz

2012-06-07T23:59:59.000Z

486

Jets in heavy ion collisions with ATLAS  

E-Print Network [OSTI]

The energy loss of high-p_T partons provides insight into the transport properties of the medium created in relativistic heavy ion collisions. Evidence for this energy loss was first experimentally established through observation of high-p_T hadron suppression at RHIC. More recently, measurements of fully reconstructed jets have been performed at the LHC. In this summary the latest experimental results from the ATLAS collaboration on jet suppression are presented. In particular the jet suppression in inclusive jet yields, path length dependence of the jet suppression, photon-jet and Z^0-jet correlations, heavy flavor suppression, and jet fragmentation are discussed. These results establish qualitative features of the jet quenching mechanism as experimental fact and provide constraints on models of jet energy loss.

Martin Spousta; for the ATLAS Collaboration

2012-11-14T23:59:59.000Z

487

Fragmentation in central collisions of heavy systems  

SciTech Connect (OSTI)

One of the goals of heavy ion reaction studies is to understand the fragmentation of hot nuclei. The LBL/GSI Plastic Ball detector system has been used to achieve a very high solid angle for detection of light and medium-heavy fragments emitted in 200 Mev/A Au + Au and Au + Fe reactions. The simultaneous measurement of almost all of the nucleons and nuclei resulting from each collision allows an estimation of the total charged particle multiplicity and hence the impact parameter. By choosing subsets of the data corresponding to a peripheral or central collision, the assumptions inherent in various models of nuclear fragmentation can be tested. 3 refs., 3 figs.

Claesson, G.; Doss, K.G.R.; Ferguson, R.; Gavron, A.; Gustafsson, H.A.; Gutbrod, H.H.; Harris, J.W.; Jacak, B.V.; Kampert, K.H.; Kolb, B.

1987-01-01T23:59:59.000Z

488

Quark condensate for various heavy flavors  

E-Print Network [OSTI]

The quark condensate is calculated within the world-line effective-action formalism, by using for the Wilson loop an ansatz provided by the stochastic vacuum model. Starting with the relation between the quark and the gluon condensates in the heavy-quark limit, we diminish the current quark mass down to the value of the inverse vacuum correlation length, finding in this way a 64%-decrease in the absolute value of the quark condensate. In particular, we find that the conventional formula for the heavy-quark condensate cannot be applied to the c-quark, and that the corrections to this formula can reach 23% even in the case of the b-quark. We also demonstrate that, for an exponential parametrization of the two-point correlation function of gluonic field strengths, the quark condensate does not depend on the non-confining non-perturbative interactions of the stochastic background Yang-Mills fields.

Dmitri Antonov; Jose Emilio F. T. Ribeiro

2012-10-04T23:59:59.000Z

489

Search for Heavy Resonances at the LHC  

E-Print Network [OSTI]

Numerous models beyond the Standard Model theory predict new heavy particles or high energy phenomena that would appear as heavy resonances in collider data. Such a signature was thus actively searched for by the ATLAS and CMS collaborations using the LHC 8 TeV proton-proton collisions. The most recent analyses using the full dataset (~ 20 fb-1) and probing a large variety of final states are reported in this article. No sign of new physics was discovered and the results are thus interpreted as exclusion limits in a model independent way or on various models based on the presence of extra-dimensions, a new strong sector or large symmetry groups.

Crépé-Renaudin, Sabine; The ATLAS collaboration

2015-01-01T23:59:59.000Z

490

The heavy top quark and supersymmetry  

SciTech Connect (OSTI)

Three aspects of supersymmetric theories are discussed: electroweak symmetry breaking, the issues of flavor, and gauge unification. The heavy top quark plays an important, sometimes dominant, role in each case. Additional symmetries lead to extensions of the Standard Model which can provide an understanding for many of the outstanding problems of particle physics.