Powered by Deep Web Technologies
Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Effect of Composition and Heat Treatment on MnBi Magnetic Materials  

SciTech Connect (OSTI)

The metallic compound MnBi is a promising rare-earth-free permanent magnet material. Compare to other rare-earth-free candidates, MnBi stands out for its high intrinsic coercivity (Hci) and its large positive temperature coefficient. Several groups have demonstrated that the Hci of MnBi compound in thin film or in powder form can exceed 12 kOe and 26 kOe at 300 K and 523 K, respectively. Such steep increase in Hci with increasing temperature is unique to MnBi. Consequently, MnBi is a highly sought-after hard phase for exchange coupling nanocomposite magnets. The reaction between Mn and Bi is peritectic, so Mn tends to precipitate out of the MnBi liquid during the solidification process. As result, the composition of the Mn-Bi alloy with the largest amount of the desired LTP (low temperature phase) MnBi and highest saturation magnetization will be over-stoichiometric and rich in Mn. The amount of additional Mn required to compensate the Mn precipitation depends on solidification rate: the faster the quench speed, the less Mn precipitates. Here we report a systematic study of the effect of composition and heat treatments on the phase contents and magnetic properties of Mn-Bi alloys. In this study, Mn-Bi alloys with 14 compositions were prepared using conventional metallurgical methods such as arc melting and vacuum heat treatment, and the obtained alloys were analyzed for compositions, crystal structures, phase content, and magnetic properties. The results show that the composition with 55 at.% Mn exhibits the highest LTP MnBi content and the highest magnetization. The sample with this composition shows >90 wt.% LTP MnBi content. Its measured saturation magnetization is 68 emu/g with 2.3 T applied field at 300 K; its coercivity is 13 kOe and its energy product is 12 MGOe at 300 K. A bulk magnet fabricated using this powder exhibits an energy product of 8.2 MGOe.

Cui, Jun; Choi, Jung-Pyung; Polikarpov, Evgueni; Bowden, Mark E.; Xie, Wei; Li, Guosheng; Nie, Zimin; Zarkevich, Nikolai; Kramer, Matthew J.; Johnson, Duane D.

2014-08-17T23:59:59.000Z

2

Effect of composition and heat treatment on MnBi magnetic materials  

SciTech Connect (OSTI)

The metallic compound MnBi is a promising rare-earth-free permanent magnet material, unique among all candidates for its high intrinsic coercivity (Hci) and its large positive temperature coefficient. The Hci of MnBi in thin-film or powder form can exceed 12 and 26 kOe at 300 and 523 K, respectively. Such a steep rise in Hci with increasing temperature is unique to MnBi. Consequently, MnBi is a highly sought-after hard phase for exchange coupling nanocomposite magnets. However, the reaction between Mn and Bi is peritectic, and hence Mn tends to precipitate out of the MnBi liquid during the solidification process. As result, when the alloy is prepared using conventional induction or arc-melting casting methods, additional Mn is required to compensate the precipitation of Mn. In addition to composition, post-casting annealing plays an important role in obtaining a high content of MnBi low-temperature phase (LTP) because the annealing encourages the Mn precipitates and the unreacted Bi to react, forming the desired LTP phase. Here we report a systematic study of the effect of composition and heat treatments on the phase content and magnetic properties of Mn–Bi alloys. In this study, 14 compositions were prepared using conventional metallurgical methods, and the compositions, crystal structures, phase content and magnetic properties of the resulting alloys were analyzed. The results show that the composition with 55 at.% Mn exhibits both the highest LTP content (93 wt.%) and magnetization (74 emu g?1 with 9 T applied field at 300 K).

Cui, Jun [Pacific Northwest National Laboratory; Choi, Jung-Pyung [Pacific Northwest National Laboratory; Polikarpov, Evgueni [Pacific Northwest National Laboratory; Bowden, Mark E [Pacific Northwest National Laboratory; Xie, Wei [Pacific Northwest National Laboratory; Li, Guosheng [Pacific Northwest National Laboratory; Nie, Zimin [Pacific Northwest National Laboratory; Zarkevich, Nikolai [Ames Laboratory; Kramer, Matthew J [Ames Laboratory; Johnson, Duane [Ames Laboratory

2014-10-01T23:59:59.000Z

3

Control system for, and a method of, heating an operator station of a work machine  

DOE Patents [OSTI]

There are situations in which an operator remains in an operator station of a work machine when an engine of the work machine is inactive. The present invention includes a control system for, and a method of, heating the operator station when the engine is inactive. A heating system of the work machine includes an electrically-powered coolant pump, a power source, and at least one piece of warmed machinery. An operator heat controller is moveable between a first and a second position, and is operable to connect the electrically-powered coolant pump to the power source when the engine is inactive and the operator heat controller is in the first position. Thus, by deactivating the engine and then moving the operator heat controller to the first position, the operator may supply electrical energy to the electrically-powered coolant pump, which is operably coupled to heat the operator station.

Baker, Thomas M.; Hoff, Brian D.; Akasam, Sivaprasad

2005-04-05T23:59:59.000Z

4

Assessment of district heating and cooling supply from Goudey Generating Station  

SciTech Connect (OSTI)

This paper addresses the feasibility analysis of retrofitting the New York State Electric and Gas (NYSEG) Goudey Generating Station for district heating and cooling supply to the SUNY-Binghamton Campus. The project involved detailed analysis of the power plant retrofit, dispatch analysis of the retrofitted Goudey Station in the New York Power Pool, environmental and permitting assessment, retrofit analysis of the SUNY campus to low temperature hot water and economic analysis.

McIntire, M.E.; Hall, D.; Beal, D.J. [New York State Electric & Gas Corporation, Binghamton, NY (United States)] [and others

1995-06-01T23:59:59.000Z

5

Heat capacity of the site-diluted spin dimer system Ba?(Mn1-xVx)?O?  

DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

Heat-capacity and susceptibility measurements have been performed on the diluted spin dimer compound Ba?(Mn1-xVx)?O?. The parent compound Ba?Mn?O? is a spin dimer system based on pairs of antiferromagnetically coupled S=1, 3d² Mn?? ions such that the zero-field ground state is a product of singlets. Substitution of nonmagnetic S=0, 3d? V?? ions leads to an interacting network of unpaired Mn moments, the low-temperature properties of which are explored in the limit of small concentrations 0?x?0.05. The zero-field heat capacity of this diluted system reveals a progressive removal of magnetic entropy over an extended range of temperatures, with no evidence for a phase transition. The concentration dependence does not conform to expectations for a spin-glass state. Rather, the data suggest a low-temperature random singlet phase, reflecting the hierarchy of exchange energies found in this system.

Samulon, E. C.; Shapiro, M. C.; Fisher, I. R.

2011-08-01T23:59:59.000Z

6

Effect of Composition and Heat Treatment on MnBi Magnetic Materials...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Abstract: The metallic compound MnBi is a promising rare-earth-free permanent magnet material. Compare to other rare-earth-free candidates, MnBi stands out for its high...

7

Solar heating and domestic hot water system installed at Kansas City, Fire Station, Kansas City, Missouri. Final report  

SciTech Connect (OSTI)

This document is the final report of the solar energy heating and hot water system installed at the Kansas City Fire Station, Number 24, 2309 Hardesty Street, Kansas City, Missouri. The solar system was designed to provide 47 percent of the space heating, 8800 square feet area and 75 percent of the domestic hot water (DHW) load. The solar system consists of 2808 square feet of Solaron, model 2001, air, flat plate collector subsystem, a concrete box storage subsystem which contains 1428 cubic feet of 1/2 inch diameter pebbles weighing 71 1/2 tons, a DHW preheat tank, blowers, pumps, heat exchangers, air ducting, controls and associated plumbing. Two 120-gallon electric DHW heaters supply domestic hot water which is preheated by the solar system. Auxiliary space heating is provided by three electric heat pumps with electric resistance heaters and four 30-kilowatt electric unit heaters. There are six modes of system operation. This project is part of the Department of Energy PON-1 Solar Demonstration Program with DOE cost sharing $154,282 of the $174,372 solar system cost. The Final Design Review was held March 1977, the system became operational March 1979 and acceptance test was completed in September 1979.

None

1980-07-01T23:59:59.000Z

8

Corrosion behavior in high heat input welded heat-affected zone of Ni-free high-nitrogen Fe–18Cr–10Mn–N austenitic stainless steel  

SciTech Connect (OSTI)

The pitting corrosion and interphase corrosion behaviors in high heat input welded heat-affected zone (HAZ) of a metastable high-nitrogen Fe–18Cr–10Mn–N austenitic stainless steel were explored through electrochemical tests. The HAZs were simulated using Gleeble simulator with high heat input welding condition of 300 kJ/cm and the peak temperature of the HAZs was changed from 1200 °C to 1350 °C, aiming to examine the effect of ?-ferrite formation on corrosion behavior. The electrochemical test results show that both pitting corrosion resistance and interphase corrosion resistance were seriously deteriorated by ?-ferrite formation in the HAZ and their aspects were different with increasing ?-ferrite fraction. The pitting corrosion resistance was decreased by the formation of Cr-depleted zone along ?-ferrite/austenite (?) interphase resulting from ?-ferrite formation; however it didn't depend on ?-ferrite fraction. The interphase corrosion resistance depends on the total amount of Cr-depleted zone as well as ferrite area and thus continuously decreased with increasing ?-ferrite fraction. The different effects of ?-ferrite fraction on pitting corrosion and interphase corrosion were carefully discussed in terms of alloying elements partitioning in the HAZ based on thermodynamic consideration. - Highlights: • Corrosion behavior in the weld HAZ of high-nitrogen austenitic alloy was studied. • Cr{sub 2}N particle was not precipitated in high heat input welded HAZ of tested alloy. • Pitting corrosion and interphase corrosion show a different behavior. • Pitting corrosion resistance was affected by whether or not ?-ferrite forms. • Interphase corrosion resistance was affected by the total amount of ?-ferrite.

Moon, Joonoh, E-mail: mjo99@kims.re.kr; Ha, Heon-Young; Lee, Tae-Ho

2013-08-15T23:59:59.000Z

9

ARM Energy Balance Bowen Ratio (EBBR) station: surf. heat flux and related data, 30-min  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

The Energy Balance Bowen Ratio (EBBR) system produces 30-min estimates of the vertical fluxes of sensible and latent heat at the local surface. Flux estimates are calculated from observations of net radiation, soil surface heat flux, and the vertical gradients of temperature and relative humidity. Meteorological data collected by the EBBR are used to calculate bulk aerodynamic fluxes, which are used in the Bulk Aerodynamic Technique (BA) EBBR value-added product (VAP) to replace sunrise and sunset spikes in the flux data. A unique aspect of the system is the automatic exchange mechanism (AEM), which helps to reduce errors from instrument offset drift.

Cook, David

10

Underground nuclear power station using self-regulating heat-pipe controlled reactors  

DOE Patents [OSTI]

A nuclear reactor for generating electricity is disposed underground at the bottom of a vertical hole that can be drilled using conventional drilling technology. The primary coolant of the reactor core is the working fluid in a plurality of thermodynamically coupled heat pipes emplaced in the hole between the heat source at the bottom of the hole and heat exchange means near the surface of the earth. Additionally, the primary coolant (consisting of the working flud in the heat pipes in the reactor core) moderates neutrons and regulates their reactivity, thus keeping the power of the reactor substantially constant. At the end of its useful life, the reactor core may be abandoned in place. Isolation from the atmosphere in case of accident or for abandonment is provided by the operation of explosive closures and mechanical valves emplaced along the hole. This invention combines technology developed and tested for small, highly efficient, space-based nuclear electric power plants with the technology of fast-acting closure mechanisms developed and used for underground testing of nuclear weapons. This invention provides a nuclear power installation which is safe from the worst conceivable reactor accident, namely, the explosion of a nuclear weapon near the ground surface of a nuclear power reactor.

Hampel, Viktor E. (Pleasanton, CA)

1989-01-01T23:59:59.000Z

11

An underground nuclear power station using self-regulating heat-pipe controlled reactors  

DOE Patents [OSTI]

A nuclear reactor for generating electricity is disposed underground at the bottom of a vertical hole that can be drilled using conventional drilling technology. The primary coolant of the reactor core is the working fluid in a plurality of thermodynamically coupled heat pipes emplaced in the hole between the heat source at the bottom of the hole and heat exchange means near the surface of the earth. Additionally, the primary coolant (consisting of the working fluid in the heat pipes in the reactor core) moderates neutrons and regulates their reactivity, thus keeping the power of the reactor substantially constant. At the end of its useful life, the reactor core may be abandoned in place. Isolation from the atmosphere in case of accident or for abandonment is provided by the operation of explosive closures and mechanical valves emplaced along the hole. This invention combines technology developed and tested for small, highly efficient, space-based nuclear electric power plants with the technology of fast- acting closure mechanisms developed and used for underground testing of nuclear weapons. This invention provides a nuclear power installation which is safe from the worst conceivable reactor accident, namely, the explosion of a nuclear weapon near the ground surface of a nuclear power reactor. 5 figs.

Hampel, V.E.

1988-05-17T23:59:59.000Z

12

A Case Study of a Commissioning Process for Demand Side Energy Conservation of the Large Heat Source Plant in Kyoto Station Building-APCBC  

E-Print Network [OSTI]

5 Heat source plant ?Total capacity?26.3MW? Substation ? ? ? Total : 6 Substations Bleed-in Control Substation ? ? ? The chilled water delivery system Large heat source plant similar to a DHC plant ? Total refrigerator capacity 26.3 MW ? Chilled... water is supplied 6 substations - Department store - Hotel - Theater - Train station etc. ? Bleed-in Control ? Commonly equipped in the substations of DHC plants. ? This control maintains the return water temperature to the plant by controlling...

Matsushita, N.; Yoshida,H.

2014-01-01T23:59:59.000Z

13

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

4: Energy Station Grid electricity Cogen Heat Exhaust (CO2)Recycled Reformate Grid electricity Cogen Heat Electricity

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

14

Exploring Mbar shock conditions and isochorically heated aluminum at the Matter in Extreme Conditions end station of the Linac Coherent Light Source (invited)  

SciTech Connect (OSTI)

Recent experiments performed at the Matter in Extreme Conditions end station of the Linac Coherent Light Source (LCLS) have demonstrated the first spectrally resolved measurements of plasmons from isochorically heated aluminum. The experiments have been performed using a seeded 8-keV x-ray laser beam as a pump and probe to both volumetrically heat and scatter x-rays from aluminum. Collective x-ray Thomson scattering spectra show a well-resolved plasmon feature that is down-shifted in energy by 19 eV. In addition, Mbar shock pressures from laser-compressed aluminum foils using velocity interferometer system for any reflector have been measured. The combination of experiments fully demonstrates the possibility to perform warm dense matter studies at the LCLS with unprecedented accuracy and precision.

Fletcher, L. B. [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Physics Department, University of California Berkeley, Berkeley, California 94709 (United States); Lee, H. J.; Gauthier, M.; Galtier, E.; Nagler, B.; Heimann, P.; Hastings, J. B.; Glenzer, S. H. [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Barbrel, B.; Falcone, R. W. [Physics Department, University of California Berkeley, Berkeley, California 94709 (United States); Döppner, T.; LePape, S.; Ma, T.; Pak, A.; Turnbull, D. [Lawrence Livermore National Laboratory, P.O. Box 808, Livermore, California 94551 (United States); White, T.; Gregori, G. [Department of Physics, University of Oxford, Parks Road, Oxford OX1 3PU (United Kingdom); Wei, M. [General Atomics, San Diego, California 87544 (United States); Zastrau, U. [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Institute for Optics and Quantum Electronics, Friedrich-Schiller-University, 07743 Jena (Germany)

2014-11-15T23:59:59.000Z

15

Cleanup Verification Package for the 100-K-55:1 and 100-K-56:1 Pipelines and the 116-KW-4 and 116-KE-5 Heat Recovery Stations  

SciTech Connect (OSTI)

This cleanup verification package documents completion of remedial action for the 100-K-55:1 and 100-K-56:1 reactor cooling effluent underground pipelines and for the 116-KW-4 and 116-KE-5 heat recovery stations. The 100-K-55 and 100-K-56 sites consisted of those process effluent pipelines that serviced the 105-KW and 105-KE Reactors.

J. M. Capron

2005-09-28T23:59:59.000Z

16

Development of By-Pass Blending Station System  

E-Print Network [OSTI]

A new building blending station system named by-pass blending station (BBS) has been developed to reduce building pump energy consumption in both district heating and cooling systems. Theoretical investigation demonstrated that the BBS can...

Liu, M.; Barnes, D.; Bunz, K.; Rosenberry, N.

2003-01-01T23:59:59.000Z

17

Assessment of district energy supply from Schiller Generating Station  

SciTech Connect (OSTI)

This paper addresses the feasibility analysis of retrofitting the Public Service of New Hampshire Schiller Generating Station to supply district heating to potential customers. The project involved analysis of power plant retrofit and comparison of district heating cost to the cost of heat supplied with gas boilers for a housing development in close proximity to the Schiller Station.

Hitchko, M. [Public Service Company of New Hampshire, Portsmouth, NH (United States); Major, W. [Joseph Technology Corporation, Inc., Woodcliff Lake, NJ (United States)

1995-06-01T23:59:59.000Z

18

Extension and improvement of Central Station District heating budget period 1 and 2, Krakow Clean Fossil Fuels and Energy Efficiency Program. Final report  

SciTech Connect (OSTI)

Project aim was to reduce pollution levels in the City of Krakow through the retirement of coal-fired (hand and mechanically-stoked) boiler houses. This was achieved by identifying attractive candidates and connecting them to the Krakow district heating system, thus permitting them to eliminate boiler operations. Because coal is less costly than district hot water, the district heating company Miejskie Przedsiebiorstwo Energetyki Cieplnej S.A., henceforth identified as MPEC, needed to provide potential customers with incentives for purchasing district heat. These incentives consisted of offerings which MPEC made to the prospective client. The offerings presented the economic and environmental benefits to district heating tie-in and also could include conservation studies of the facilities, so that consumption of energy could be reduced and the cost impact on operations mitigated. Because some of the targeted boiler houses were large, the capacity of the district heating network required enhancement at strategic locations. Consequently, project construction work included both enhancement to the district piping network as well as facility tie-ins. The process of securing new customers necessitated the strengthening of MPEC`s competitive position in Krakow`s energy marketplace, which in turn required improvements in marketing, customer service, strategic planning, and project management. Learning how US utilities address these challenges became an integral segment of the project`s scope.

NONE

1997-07-01T23:59:59.000Z

19

City of College Station's Thermographic Mobile Scan  

E-Print Network [OSTI]

During the first quarter of 1986, the City of College Station conducted a thermographic mobile scan of the entire city. A thermographic mobile scan is a process by which heat loss/heat gain data is accumulated by a vehicle traveling the city...

Shear, C. K.

1986-01-01T23:59:59.000Z

20

SOUTH STATION TAmtrak, Commuter  

E-Print Network [OSTI]

SOUTH STATION TAmtrak, Commuter Rail, Bus Station, MBTA Red Line Knapp St. Kneeland St. Stuart St) T BOYLSTON (MBTA Green Line) T NEW ENGLAND MEDICAL CENTER (MBTA Orange Line) Boston Campus Accessibility Map

Dennett, Daniel

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Franklin Heating Station | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating Solar Power Basics (TheEtelligence (SmartHome Kyoung'sfor

22

Bulk modulus and specific heat of B-site doped (La{sub 0.3}Pr{sub 0.7}){sub 0.65}Ca{sub 0.35}Mn{sub 1?x}B{sub x}O{sub 3} (B=Fe, Cr, Ru, Al, Ga)  

SciTech Connect (OSTI)

Specific heat (C{sub p}) thermal expansion (?) and Bulk modulus (B{sub T}) of lightly doped Rare Earth manganites (La{sub 0.3}Pr{sub 0.7}){sub 0.65}Ca{sub 0.35}Mn{sub 1?x}B{sub x}O{sub 3} (B{sup 3+}?=?Fe{sup 3+},Cr{sup 3+},Ga{sup 3+},Al{sup 3+},Ru4+); (0.3heat (C{sub p}){sub lat} of (La{sub 0.3}Pr{sub 0.7}){sub 0.65}Ca{sub 0.35}Mn{sub 0.97}Fe{sub 0.03}O{sub 3} as a function of temperature (10K?T? 200K) is found to be in agreement with the published data. The trend of variation of Debye temperature with B-site cationic radius is predicted probably for the first time for the B-site doped rare earth manganites.

Srivastava, Archana, E-mail: archanasaran01@gmail.com [Department of Physics, Sri Sathya Sai College for Women, Bhopal-462024 (India); Thakur, Rasna; Gaur, N. K. [Department of Physics, Barkatullah University, Bhopal-462026 (India)

2014-04-24T23:59:59.000Z

23

The CNGS Target Station Presented by L.Bruno  

E-Print Network [OSTI]

sealed system filled with 0.5 bar of He. The tube has annular fins to enhance convective heat transfer enclosure Inlet target Inlet fixed shielding Outlet Beam #12;The target Assembly The CNGS Target Station as

McDonald, Kirk

24

Central Station DHC Phase 1 feasibility  

SciTech Connect (OSTI)

This project assisted a private real estate developer in technically assessing the feasibility of integrating a central DHC system into a proposed 72 acre area mixed-use Planned Development (Central Station) just south of the Chicago Central Business District (Loop). The technical assessment concluded that a district heating and cooling system for Central Station will be feasible, provided that a major anchor load can be connected to the system. The system conceived for the site employs a modular approach that adjusts production capacity to actual load growth. The design concept includes gas-fired boilers for heating, gas turbine driven chillers for base loading, electric motor driven chillers for peaking, steam turbines for peak power and back pressure operation, and chilled water storage. Energy will be supplied to the users in the form of steam or low temperature hot water for heating, and low temperature chilled water for cooling.

Henderson, H.L.

1992-03-01T23:59:59.000Z

25

Summer HeatSummer Heat Heat stress solutions  

E-Print Network [OSTI]

occur (then drink a lightly salted beverage like a sports drink). The water's temperature should be cool How should gardeners avoid becoming a safety threat to themselves and others when it's hot? Start to the heat. Become a weather watcher. Set up a small weather station (with a high/low thermom eter, rain

Liskiewicz, Maciej

26

PMEL Ocean Climate Station Program Meghan Cronin, Chris Sabine, Chris Meinig  

E-Print Network [OSTI]

. Papa HOT MBARI Cold dry air blowing over warm Kuroshio Extension causes large sensible and latent heat for climate reference) Net Surface Heat Flux = TurbPMEL Ocean Climate Station Program Meghan Cronin, Chris Sabine, Chris Meinig NOAA Pacific Marine

27

Metastable phase boundaries of quasicrystalline phases. [Al-Mn; Al-Ru  

SciTech Connect (OSTI)

The melting curve (T/sub 0/) of the metastable icosahedral phase and the liquidus of the decagonal phase of Al-Mn have been obtained for 14 to 22 at. % Mn. Icosahedral Al-Mn has a congruent melting point of 910 +- 20/sup 0/C at 20 at. % Mn, and melts approx.30/sup 0/C lower than crystalline compounds with the same composition. Icosahedral Al/sub 82/Ru/sub 18/ was determined to melt at 1260 +- 30/sup 0/C. These results were obtained by forming single-phase icosahedral alloys with ion beam mixing, and by rapid heating to accurately known temperatures with electron beams.

Follstaedt, D.M.; Knapp, J.A.

1987-01-01T23:59:59.000Z

28

Advance View Proofs Thermodynamic Description of the Mg-Mn, Al-Mn and Mg-Al-Mn Systems  

E-Print Network [OSTI]

Advance View Proofs Thermodynamic Description of the Mg-Mn, Al-Mn and Mg-Al-Mn Systems Using-consistent thermodynamic model of the Mg-Mn, Al-Mn and Mg-Al-Mn systems has been developed. The major difference between work on the Al-Mn system that uses the same model for the liquid phase reveals that better agreement

Medraj, Mamoun

29

Melting point measurements for quasicrystalline phases. [Al-Mn; icosahedral and decagonal phases  

SciTech Connect (OSTI)

Melting transitions of metastable quasicrystalline phases of Al-Mn have been observed using rapid electron-beam heating of fine-grained icosahedral surface layers. The congruent melting point for icosahedral Al/sub 80/Mn/sub 20/ was directly measured to be 910 +- 20/sup 0/C. Heating to higher temperatures shows another transition which is inferred to correspond to the liquidus of the decagonal phase at 965 +- 20/sup 0/C for 20 at. % Mn. The microstructure and formation kinetics of the decagonal phase are discussed, and its electron diffraction is described.

Knapp, J.A.; Follstaedt, D.M.

1986-01-01T23:59:59.000Z

30

M Station, Austin  

E-Print Network [OSTI]

SUNSHINE MATHON, M. Arch., LEED Homes AP Design + Development Director sunshine.mathon@foundcom.org FOUNDATION COMMUNITIES Austin, TX T.O.D. District Area T.O.D. District Area T.O.D. District Area T.O.D. District Area 8.5 ACRE SITE 5-1.../2 Acres Buildable Boggy Creek Floodplain 8.5 ACRE SITE 5-1/2 Acres Buildable Boggy Creek Floodplain 4 Acres Concrete Abandoned Grayfield M STATION 80% 2 & 3-Bedrooms 150 1,2 & 3-Bedroom Apts M STATION 80% 2 & 3-Bedrooms 150 1,2 & 3-Bedroom Apts...

Mathon, S.

2011-01-01T23:59:59.000Z

31

Determination of solid fractiontemperature relation and latent heat using full scale  

E-Print Network [OSTI]

on five such corrosion resistant alloys: superaustenitic stainless steel CN3MN, duplex stainless steels CD available. The alloys selected consist of three stainless steels (super- austenitic CN3MN and duplexes CD3MN, Latent heat, Stainless steels, Nickel based alloys Introduction Casting simulation is routinely used

Beckermann, Christoph

32

Skate Station UF Services  

E-Print Network [OSTI]

friends, practice your English, and try new activities! Where: Skate Station Funworks We will be meeting and more orderly manner. Everyone will be served eventually. Fire Drills/Alarms: Whenever you hear a fire should park your bike in well-lighted areas and lock it up when you park it. The best lock is a U

Pilyugin, Sergei S.

33

Hydrogen Filling Station  

SciTech Connect (OSTI)

Hydrogen is an environmentally attractive transportation fuel that has the potential to displace fossil fuels. The Freedom CAR and Freedom FUEL initiatives emphasize the importance of hydrogen as a future transportation fuel. Presently, Las Vegas has one hydrogen fueling station powered by natural gas. However, the use of traditional sources of energy to produce hydrogen does not maximize the benefit. The hydrogen fueling station developed under this grant used electrolysis units and solar energy to produce hydrogen fuel. Water and electricity are furnished to the unit and the output is hydrogen and oxygen. Three vehicles were converted to utilize the hydrogen produced at the station. The vehicles were all equipped with different types of technologies. The vehicles were used in the day-to-day operation of the Las Vegas Valley Water District and monitoring was performed on efficiency, reliability and maintenance requirements. The research and demonstration utilized for the reconfiguration of these vehicles could lead to new technologies in vehicle development that could make hydrogen-fueled vehicles more cost effective, economical, efficient and more widely used. In order to advance the development of a hydrogen future in Southern Nevada, project partners recognized a need to bring various entities involved in hydrogen development and deployment together as a means of sharing knowledge and eliminating duplication of efforts. A road-mapping session was held in Las Vegas in June 2006. The Nevada State Energy Office, representatives from DOE, DOE contractors and LANL, NETL, NREL were present. Leadership from the National hydrogen Association Board of Directors also attended. As a result of this session, a roadmap for hydrogen development was created. This roadmap has the ability to become a tool for use by other road-mapping efforts in the hydrogen community. It could also become a standard template for other states or even countries to approach planning for a hydrogen future. Project partners also conducted a workshop on hydrogen safety and permitting. This provided an opportunity for the various permitting agencies and end users to gather to share experiences and knowledge. As a result of this workshop, the permitting process for the hydrogen filling station on the Las Vegas Valley Water District’s land was done more efficiently and those who would be responsible for the operation were better educated on the safety and reliability of hydrogen production and storage. The lessons learned in permitting the filling station and conducting this workshop provided a basis for future hydrogen projects in the region. Continuing efforts to increase the working pressure of electrolysis and efficiency have been pursued. Research was also performed on improving the cost, efficiency and durability of Proton Exchange Membrane (PEM) hydrogen technology. Research elements focused upon PEM membranes, electrodes/catalysts, membrane-electrode assemblies, seals, bipolar plates, utilization of renewable power, reliability issues, scale, and advanced conversion topics. Additionally, direct solar-to-hydrogen conversion research to demonstrate stable and efficient photoelectrochemistry (PEC) hydrogen production systems based on a number of optional concepts was performed. Candidate PEC concepts included technical obstacles such as inefficient photocatalysis, inadequate photocurrent due to non-optimal material band gap energies, rapid electron-hole recombination, reduced hole mobility and diminished operational lifetimes of surface materials exposed to electrolytes. Project Objective 1: Design, build, operate hydrogen filling station Project Objective 2: Perform research and development for utilizing solar technologies on the hydrogen filling station and convert two utility vehicles for use by the station operators Project Objective 3: Increase capacity of hydrogen filling station; add additional vehicle; conduct safety workshop; develop a roadmap for hydrogen development; accelerate the development of photovoltaic components Project Objective 4:

Boehm, Robert F; Sabacky, Bruce; Anderson II, Everett B; Haberman, David; Al-Hassin, Mowafak; He, Xiaoming; Morriseau, Brian

2010-02-24T23:59:59.000Z

34

Pacific Southwest Research Station Publications  

E-Print Network [OSTI]

Bulletins 1- 28 1965-1989 Soil- Vegetation Tables -- 1965-1980 Solar Irradiation and Shadow Length Tables-1971 1938 California Forest and Range Experiment Station Annual Report 1939 California Forest and Range Experiment Station Annual Report 1940 California Forest and Range Experiment Station Annual Report 1951

Standiford, Richard B.

35

Heat pipe array heat exchanger  

DOE Patents [OSTI]

A heat pipe arrangement for exchanging heat between two different temperature fluids. The heat pipe arrangement is in a ounterflow relationship to increase the efficiency of the coupling of the heat from a heat source to a heat sink.

Reimann, Robert C. (Lafayette, NY)

1987-08-25T23:59:59.000Z

36

Husavik Geothermal Power Station | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat Jump to:PhotonHolyName HousingIII Wind FarmWouldOpenSchools JumpStation

37

Transit Infrastructure Finance Through Station Location Auctions  

E-Print Network [OSTI]

Numerous route and station options Strong real estate marketreal estate market Transit friendly constituents Numerous route and station options

Ian Carlton

2009-01-01T23:59:59.000Z

38

Attached algae of the Lake Erie shoreline near Nanticoke Generating Station  

SciTech Connect (OSTI)

The distribution, species composition, and standing crop of attached algae were surveyed in the splash zone along the shore of Lake Erie from 1971 to 1978 to determine the impact of construction and operation of the Nanticoke Generating Station, a coal-fired power plant. Station operation has had no apparent influence on the spatial distribution of attached algae in the lake stations. However, the discharge of heated condenser cooling water has resulted in an accelerated growth of attached algae in the immediate vicinity of the station early in the growing season, but the effect was not sustained after May. The species composition at sites near the generating station differed from control areas. Three years after the initial operation of the plant the generating station had a lower percent abundance of Cladophora and a higher percent abundance of weakly attached algal species such as Zygnema; this is perhaps attributable to the sheltered conditions in the discharge area of the generating station.

Kirby, M.K.; Dunford, W.E.

1981-11-01T23:59:59.000Z

39

Attached algae of the Lake Erie shoreline near Nanticoke generating station  

SciTech Connect (OSTI)

The distribution, species composition and standing crop of attached algae were surveyed in the splash zone along the shore of Lake Erie from 1971 to 1978 to determine the impact of construction and operation of the Nanticoke Generating Station, a coal-fired power plant. Station operation has had no apparent influence on the spatial distribution of attached algae in the lake stations. However, the discharge of heated condenser cooling water has resulted in an accelerated growth of attached algae in the immediate vicinity of the station early in the growing season, but the effect was not sustained after May. The species composition at sites near the generating station differed from control areas. Three years after the initial operation of the plant the generating station had a lower percent abundance of Cladophora and a higher percent abundance of weakly attached algal species such as Zygnema; this is perhaps attributable to the sheltered conditions in the discharge area of the generating station.

Kirby, M.K.; Dunford, W.E.

1981-01-01T23:59:59.000Z

40

Wachs Cutter Tooling Station (4495)  

Broader source: Energy.gov (indexed) [DOE]

purchase, build and install Wachs cutter tooling. The Wachs Cutter Tooling Station is similar to previously operated facility tooling and will utilize an existing hydraulic unit....

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Station design using orifice meters  

SciTech Connect (OSTI)

This paper reports that proper meter station design using gas orifice meters must include consideration of a number of factors to minimize operation and maintenance problems while obtaining the best accuracy over the life of the station. A station should provide accuracy, be safe, functional, economical and free of undue maintenance. It should comply with all codes, reports and specifications but most of all it should be able to comply with terms set forth in the contract. All measuring stations should be designed with considerations of growth or reductions in volume. It should be attractive and built to last for many years.

Upp, E.L. (Daniel Industries, Inc., Houston, TX (United States))

1992-07-01T23:59:59.000Z

42

Fuel Station Procedure Applicability All  

E-Print Network [OSTI]

Fuel Station Procedure Applicability All Last Revised 11/20/12 Procedure Owner Andrew Grant agrant for the purchasing and distribution of fuel for vehicles owned by Bowling Green State University (BGSU). This centralization is important to ensure compliance for BGSU employees who use the centralized fuel station and fuel

Moore, Paul A.

43

Technical Analysis of the Hydrogen Energy Station Concept, Phase I and Phase II  

SciTech Connect (OSTI)

Phase I Due to the growing interest in establishing a domestic hydrogen infrastructure, several hydrogen fueling stations already have been established around the country as demonstration units. While these stations help build familiarity with hydrogen fuel in their respective communities, hydrogen vehicles are still several years from mass production. This limited number of hydrogen vehicles translates to a limited demand for hydrogen fuel, a significant hurdle for the near-term establishment of commercially viable hydrogen fueling stations. By incorporating a fuel cell and cogeneration system with a hydrogen fueling station, the resulting energy station can compensate for low hydrogen demand by providing both hydrogen dispensing and combined heat and power (CHP) generation. The electrical power generated by the energy station can be fed back into the power grid or a nearby facility, which in turn helps offset station costs. Hydrogen production capacity not used by vehicles can be used to support building heat and power loads. In this way, an energy station can experience greater station utility while more rapidly recovering capital costs, providing an increased market potential relative to a hydrogen fueling station. At an energy station, hydrogen is generated on-site. Part of the hydrogen is used for vehicle refueling and part of the hydrogen is consumed by a fuel cell. As the fuel cell generates electricity and sends it to the power grid, excess heat is reclaimed through a cogeneration system for use in a nearby facility. Both the electrical generation and heat reclamation serve to offset the cost of purchasing the equivalent amount of energy for nearby facilities and the energy station itself. This two-phase project assessed the costs and feasibility of developing a hydrogen vehicle fueling station in conjunction with electricity and cogenerative heat generation for nearby Federal buildings. In order to determine which system configurations and operational patterns would be most viable for an energy station, TIAX developed several criteria for selecting a representative set of technology configurations. TIAX applied these criteria to all possible technology configurations to determine an optimized set for further analysis, as shown in Table ES-1. This analysis also considered potential energy station operational scenarios and their impact upon hydrogen and power production. For example, an energy station with a 50-kWe reformer could generate enough hydrogen to serve up to 12 vehicles/day (at 5 kg/fill) or generate up to 1,200 kWh/day, as shown in Figure ES-1. Buildings that would be well suited for an energy station would utilize both the thermal and electrical output of the station. Optimizing the generation and utilization of thermal energy, hydrogen, and electricity requires a detailed look at the energy transfer within the energy station and the transfer between the station and nearby facilities. TIAX selected the Baseline configuration given in Table ES-1 for an initial analysis of the energy and mass transfer expected from an operating energy station. Phase II The purpose of this technical analysis was to analyze the development of a hydrogen-dispensing infrastructure for transportation applications through the installation of a 50-75 kW stationary fuel cell-based energy station at federal building sites. The various scenarios, costs, designs and impacts of such a station were quantified for a hypothetical cost-shared program that utilizes a natural gas reformer to provide hydrogen fuel for both the stack(s) and a limited number of fuel cell powered vehicles, with the possibility of using cogeneration to support the building heat load.

TIAX, LLC

2005-05-04T23:59:59.000Z

44

Ferromagnetic transition temperature enhancement in (Ga,Mn)As semiconductors by carbon codoping  

E-Print Network [OSTI]

-1829/2003/68~16!/161202~4!/$20.00 68 161202- t in ?Ga,Mn?As semiconductors codoping ,2,4 and A. H. MacDonald2 a? 10, 162 53 Praha 6, Czech Republic y Station C1600, Austin, Texas 78712-0264, USA 2, 182 21 Praha 8, Czech Republic y, College Station, Texas 77843-4242, USA d 13... Society1 RAPID COMMUNICATIONS JUNGWIRTH, MASE? K, SINOVA, AND MacDONALD PHYSICAL REVIEW B 68, 161202~R! ~2003! The above qualitative analysis of formation energies sug- gests that CAs codoping is favorable for achieving high Curie temperatures. Unlike...

Jungwirth, T.; Masek, J.; Sinova, Jairo; MacDonald, AH.

2003-01-01T23:59:59.000Z

45

Synthesis of Li{sub (x)}Na{sub (2-x)}Mn{sub 2}S{sub 3} and LiNaMnS{sub 2} through redox-induced ion exchange reactions  

SciTech Connect (OSTI)

Na{sub 2}Mn{sub 2}S{sub 3} was oxidatively deintercalated using iodine in acetonitrile to yield Na{sub 1.3}Mn{sub 2}S{sub 3}, with lattice constants nearly identical to that of the reactant. Lithium was then reductively intercalated into the oxidized product to yield Li{sub 0.7}Na{sub 1.3}Mn{sub 2}S{sub 3}. When heated, this metastable compound decomposed to form a new crystalline compound, LiNaMnS{sub 2}, along with MnS and residual Na{sub 2}Mn{sub 2}S{sub 3}. Single crystal X-ray diffraction structural analysis of LiNaMnS{sub 2} revealed that this compound crystallizes in P-3m1 with cell parameters a=4.0479(6) A, c=6.7759(14) A, V=96.15(3) A{sup 3} (Z=1, wR2=0.0367) in the NaLiCdS{sub 2} structure-type. - Graphical abstract: Structure of LiNaMnS{sub 2}. Li and Mn are statistically distributed in edge-shared tetrahedral environments linked into infinite planes. Sodium ions occupy interlayer sites.

Luthy, Joshua A.; Goodman, Phillip L. [Department of Chemistry and Biochemistry, Texas State University-San Marcos, 601 University Drive, San Marcos, TX 78666 (United States); Martin, Benjamin R. [Department of Chemistry and Biochemistry, Texas State University-San Marcos, 601 University Drive, San Marcos, TX 78666 (United States)], E-mail: bmartin@txstate.edu

2009-03-15T23:59:59.000Z

46

Ferrimagnetism and disorder of epitaxial Mn2-xCoxVAl Heusler compound thin films  

SciTech Connect (OSTI)

The quaternary full Heusler compound Mn{sub 2-x}Co{sub x}VAl with x = 1 is predicted to be a half-metallic antiferromagnet. Thin films of the quaternary compounds with x = 0-2 were prepared by dc and RF magnetron co-sputtering on heated MgO (0 0 1) substrates. The magnetic structure was examined by x-ray magnetic circular dichroism and the chemical disorder was characterized by x-ray diffraction. Ferrimagnetic coupling of V to Mn was observed for Mn{sub 2}VAl (x = 0). For x = 0.5, we also found ferrimagnetic order with V and Co antiparallel to Mn. The observed reduced magnetic moments are interpreted with the help of band structure calculations in the coherent potential approximation. Mn{sub 2}VAl is very sensitive to disorder involving Mn, because nearest-neighbour Mn atoms couple antiferromagnetically. Co{sub 2}VAl has B2 order and has reduced magnetization. In the cases with x {ge} 0.9 conventional ferromagnetism was observed, closely related to the atomic disorder in these compounds.

Meinert, Markus; Schmalhorst, Jan-Michael; Reiss, Gunter; Arenholz, Elke

2011-01-29T23:59:59.000Z

47

Electrolysis at Forecourt Stations  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeat PumpRecord ofESPC ENABLE: ECMConstruction and AnalysisClothesCLEAN FUEL ITM

48

Structure and magnetic properties of rf thermally plasma synthesized Mn and MnZn ferrite nanoparticles  

E-Print Network [OSTI]

Structure and magnetic properties of rf thermally plasma synthesized Mn and Mn­Zn ferrite has previously been shown to be a viable route to producing nanocrystalline magnetite and Ni ferrite nanoparticles. In this work nanocrystalline powders of Mn and Mn­Zn ferrites have been synthesized using a 50 k

McHenry, Michael E.

49

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

4-12: Hydrogen Cost Comparison for Electrolysis Station Withthe hydrogen costs from the HSCM for electrolysis stations

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

50

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network [OSTI]

Costs Annualized Investment Cost, 1000$/yr Total AnnualizedH2 Fueling Stations Investment Cost Cost ($/yr) OperatingH2 Fueling Stations Investment Cost Cost ($/kg) Operating

Weinert, Jonathan X.; Shaojun, Liu; Ogden, J; Jianxin, Ma

2006-01-01T23:59:59.000Z

51

Energy Department Launches Alternative Fueling Station Locator...  

Broader source: Energy.gov (indexed) [DOE]

Launches Alternative Fueling Station Locator App Energy Department Launches Alternative Fueling Station Locator App November 7, 2013 - 11:16am Addthis As part of the Obama...

52

MN Office of Energy Security | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpIncMAKGalway Bay IEOWCCatcher.pngWavemill <MN Office of Energy

53

Structural And Physical Characterization of Tetranuclear [Mn**II(3)Mn**IV] And [Mn**II(2)Mn**III(2)] Valence-Isomer Manganese Complexes  

SciTech Connect (OSTI)

Two tetranuclear Mn complexes with an average Mn oxidation state of +2.5 have been prepared. These valence isomers have been characterized by a combination of X-ray crystallography, X-ray absorption spectroscopy, and magnetic susceptibility. The Mn{sup II}{sub 3}Mn{sup IV} tetramer has the Mn ions arranged in a distorted tetrahedron, with an S = 6 ground spin state, dominated by ferromagnetic exchange among the manganese ions. The Mn{sup II}{sub 2}Mn{sup III}{sub 2} tetramer also has a distorted tetrahedral arrangement of Mn ions but shows magnetic behavior, suggesting that it is a single-molecule magnet. The X-ray absorption near-edge structure (XANES) spectra for the two complexes are similar, suggesting that, while Mn XANES has sufficient sensitivity to distinguish between trinuclear valence isomers (Alexiou et al. Inorg. Chem. 2003, 42, 2185), similar distinctions are difficult for tetranuclear complexes such as that found in the photosynthetic oxygen-evolving complex.

Zaleski, C.M.; Weng, T.-C.; Dendrinou-Samara, C.; Alexiou, M.; Kanakaraki, P.; Hsieh, W.-Y.; Kampf, J.; Penner-Hahn, J.E.; Pecoraro, V.L.; Kessissoglou, D.P.

2009-05-28T23:59:59.000Z

54

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

e.g. co-locate with gasoline station, bus-yard, or officeintegrated into existing gasoline stations with 8 dispensersof a liquid H 2 and gasoline station layout. Figure 4-9:

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

55

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

located at an existing gasoline station. One could use othere.g. co-locate with gasoline station, bus-yard, or officeequivalent to about 6% of gasoline stations in California 4.

Lipman, T E; Weinert, Jonathan X.

2006-01-01T23:59:59.000Z

56

Mobile Alternative Fueling Station Locator  

SciTech Connect (OSTI)

The Department of Energy's Alternative Fueling Station Locator is available on-the-go via cell phones, BlackBerrys, or other personal handheld devices. The mobile locator allows users to find the five closest biodiesel, electricity, E85, hydrogen, natural gas, and propane fueling sites using Google technology.

Not Available

2009-04-01T23:59:59.000Z

57

NOAA PMEL Station Chemistry Data  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

Submicron and supermicron samples are analyzed by ion chromatography for Cl-, NO3-, SO4-2, Na+, NH4+, K+, Mg2+, and Ca+2. The analysis of MSA-, Br-, and oxalate has been added to some stations. Samples also are analyzed for total mass by gravimetric analysis at 55 +/- 5% RH.

Quinn, Patricia

58

Presented by Climate End Station  

E-Print Network [OSTI]

.S. Department of Energy Bettge_LCF Climate_SC10 CESM working groups · Application ­ Climate change, paleoclimate climate change projections for IPCC AR5 Gerald Meehl and Warren Washington, NCAR · Climate changePresented by Climate End Station Thomas Bettge National Center for Atmospheric Research James B

59

Effect of Mn doping on the structural, morphological, optical...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Mn doping on the structural, morphological, optical and magnetic properties of indium tin oxide films. Effect of Mn doping on the structural, morphological, optical and magnetic...

60

COMPARATIVE COSTS OF CALIFORNIA CENTRAL STATION ELECTRICITY  

E-Print Network [OSTI]

CALIFORNIA ENERGY COMMISSION COMPARATIVE COSTS OF CALIFORNIA CENTRAL STATION ELECTRICITY GENERATION .............................................................................13 Definition of Levelized Cost ........................................................................................................13 Levelized Cost Components

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

COMPARATIVE COSTS OF CALIFORNIA CENTRAL STATION ELECTRICITY  

E-Print Network [OSTI]

CALIFORNIA ENERGY COMMISSION COMPARATIVE COSTS OF CALIFORNIA CENTRAL STATION ELECTRICITY GENERATION............................................................ 3 Definition of Levelized Cost.................................................................................... 3 Levelized Cost Categories

Laughlin, Robert B.

62

arXiv:1201.0642v1[astro-ph.GA]3Jan2012 Mon. Not. R. Astron. Soc. 000, 000000 (0000) Printed 4 January 2012 (MN LATEX style file v2.2)  

E-Print Network [OSTI]

January 2012 (MN LATEX style file v2.2) Stochastic grain heating and mid-infrared emission in protostellar and compared with observations of a representative infrared dark cloud core. We show that stochastic heating heating of small grains is often mentioned as a primary cause of large in- frared (IR) fluxes from star

Henning, Thomas

63

7.1.1. Fernbahnhof / Rail Station  

E-Print Network [OSTI]

Fernbahnhofs 7.1.1.4.5 Kälteversorgung des Fernbahnhofs / Cooling Supply of Rail Station 7 Abwasserversorgung des Fernbahnhofs / Fresh and Used Water Supply of Rail Stations 7.1.1.4.1.1 Verfahren zur Fernbahnhofs 7.1.1.4.2 Stromversorgung des Fernbahnhofs / Power Supply of Rail Station 7

Berlin,Technische Universität

64

The Fuel-Travel-Back Approach to Hydrogen Station Siting  

E-Print Network [OSTI]

the experience of gasoline stations. Driven by the notion "percentages of existing gasoline stations, for a successfulsubset of the existing gasoline station network [14]. These

Lin, Zhenhong; Ogden, Joan; Fan, Yueyue; Chen, Chien-Wei

2009-01-01T23:59:59.000Z

65

Carbon/lambda-MnO{sub 2} composites for supercapacitor electrodes  

SciTech Connect (OSTI)

In the present work a composite of carbon with lambda-MnO{sub 2} have been synthesized by a simple two-step route. In the first step, to obtain LiMn{sub 2}O{sub 4}/carbon material, mesoporous activated carbon was impregnated with the solution of precursor metal salts and heated subsequently. As-prepared materials were acid treated which resulted in the formation of lambda-MnO{sub 2}/carbon. Physical properties, structure and specific surface area of electrode materials were studied by TEM, X-ray diffraction and nitrogen sorption measurements. Voltammetry cycling, galvanostatic charge/discharge and impedance spectroscopy measurements performed in two- and three-electrode cells have been applied in order to measure electrochemical parameters. TEM images confirmed well dispersed lambda-MnO{sub 2} particles on the surface of carbon material. The carbon in the composite plays an important role as the surface area enhancing component and a support of pseudocapacitive material. Furthermore, the through-connected porosity serves as a continuous pathway for electrolyte transport. A synergetic effect of the porous carbon framework and of the redox properties of the lambda-MnO{sub 2} is at the origin of improvement of specific capacitance values which has been observed for composites after delithiation. - Comparison of capacitance characteristics for initial carbon and synthesised composites for CB in 1 mol L{sup -1} Na{sub 2}SO{sub 4} solution.

Malak-Polaczyk, A., E-mail: agnieszka-malak@wp.p [Institute of Chemistry and Technical Electrochemistry, Poznan University of Technology, Piotrowo 3, 60-695 Poznan (Poland); Institut de Sciences des Materiaux de Mulhouse, CNRS LRC 7228, 15 Rue Starcky, 68057 Mulhouse (France); Matei-Ghimbeu, C.; Vix-Guterl, C. [Institut de Sciences des Materiaux de Mulhouse, CNRS LRC 7228, 15 Rue Starcky, 68057 Mulhouse (France); Frackowiak, E. [Institute of Chemistry and Technical Electrochemistry, Poznan University of Technology, Piotrowo 3, 60-695 Poznan (Poland)

2010-04-15T23:59:59.000Z

66

Total Space Heating Water Heating Cook-  

Gasoline and Diesel Fuel Update (EIA)

Released: September, 2008 Total Space Heating Water Heating Cook- ing Other Total Space Heating Water Heating Cook- ing Other All Buildings* ... 1,602 1,397...

67

Total Space Heating Water Heating Cook-  

Gasoline and Diesel Fuel Update (EIA)

Released: September, 2008 Total Space Heating Water Heating Cook- ing Other Total Space Heating Water Heating Cook- ing Other All Buildings* ... 1,870 1,276...

68

Total Space Heating Water Heating Cook-  

Gasoline and Diesel Fuel Update (EIA)

Energy Consumption Survey: Energy End-Use Consumption Tables Total Space Heating Water Heating Cook- ing Other Total Space Heating Water Heating Cook- ing Other All...

69

Total Space Heating Water Heating Cook-  

Gasoline and Diesel Fuel Update (EIA)

Released: September, 2008 Total Space Heating Water Heating Cook- ing Other Total Space Heating Water Heating Cook- ing Other All Buildings ... 2,037...

70

Susanville District Heating District Heating Low Temperature...  

Open Energy Info (EERE)

Susanville District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Susanville District Heating District Heating Low Temperature...

71

Heating system  

SciTech Connect (OSTI)

A heating system utilizing solar panels and buried ground conduits to collect and store heat which is delivered to a heatpump heat exchanger. A heat-distribution fluid continuously circulates through a ground circuit to transfer heat from the ground to the heat exchanger. The ground circuit includes a length of buried ground conduit, a pump, a check valve and the heat exchanger. A solar circuit, including a solar panel and a second pump, is connected in parallel with the check valve so that the distribution fluid transfers solar heat to the heat exchanger for utilization and to the ground conduit for storage when the second pump is energized. A thermostatically instrumented control system energizes the second pump only when the temperature differential between the solar panel inlet and outlet temperatures exceeds a predetermined value and the ground temperature is less than a predetermined value. Consequently, the distribution fluid flows through the solar panel only when the panel is capable of supplying significant heat to the remainder of the system without causing excessive drying of the ground.

Nishman, P.J.

1983-03-08T23:59:59.000Z

72

High-temperature stability, structure and thermoelectric properties of CaMn1xNbxO3 phases  

E-Print Network [OSTI]

technologies such as solid oxide fuel cells, thermoelectric (TE) modules and high-temperature superconductorsHigh-temperature stability, structure and thermoelectric properties of CaMn1Ã?xNbxO3 phases Laura diffraction and electron diffraction data. Thermogravi- metric heating/cooling studies showed a reversible

73

Iron-based soft magnetic composites with MnZn ferrite nanoparticles coating obtained by solgel method  

E-Print Network [OSTI]

­gel method Shen Wu a , Aizhi Sun a,n , Wenhuan Xu a , Qian Zhang a , Fuqiang Zhai a , Philip Logan b , Alex A-ray spectroscopy and distribution maps show that the iron particle surface is covered with a thin layer of Mn compared with the epoxy resin coated samples at 10 kHz. The effects of heat treatment temperature

Volinsky, Alex A.

74

Timber Mountain Precipitation Monitoring Station  

SciTech Connect (OSTI)

A precipitation monitoring station was placed on the west flank of Timber Mountain during the year 2010. It is located in an isolated highland area near the western border of the Nevada National Security Site (NNSS), south of Pahute Mesa. The cost of the equipment, permitting, and installation was provided by the Environmental Monitoring Systems Initiative (EMSI) project. Data collection, analysis, and maintenance of the station during fiscal year 2011 was funded by the U.S. Department of Energy, National Nuclear Security Administration, Nevada Site Office Environmental Restoration, Soils Activity. The station is located near the western headwaters of Forty Mile Wash on the Nevada Test and Training Range (NTTR). Overland flows from precipitation events that occur in the Timber Mountain high elevation area cross several of the contaminated Soils project CAU (Corrective Action Unit) sites located in the Forty Mile Wash watershed. Rain-on-snow events in the early winter and spring around Timber Mountain have contributed to several significant flow events in Forty Mile Wash. The data from the new precipitation gauge at Timber Mountain will provide important information for determining runoff response to precipitation events in this area of the NNSS. Timber Mountain is also a groundwater recharge area, and estimation of recharge from precipitation was important for the EMSI project in determining groundwater flowpaths and designing effective groundwater monitoring for Yucca Mountain. Recharge estimation additionally provides benefit to the Underground Test Area Sub-project analysis of groundwater flow direction and velocity from nuclear test areas on Pahute Mesa. Additionally, this site provides data that has been used during wild fire events and provided a singular monitoring location of the extreme precipitation events during December 2010 (see data section for more details). This letter report provides a summary of the site location, equipment, and data collected in fiscal year 2011.

Lyles Brad,McCurdy Greg,Chapman Jenny,Miller Julianne

2012-01-01T23:59:59.000Z

75

List of Refueling Stations Incentives | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpInc Place:KeystoneSolarList ofPassive Solar SpaceStations Incentives

76

Hanford Meteorological Station - Hanford Site  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation Desert Southwest Region service area. TheEPSCIResearchGulf of MexicoDidYouKnowForStation

77

Itinerant and localized magnetic moments in ferrimagnetic Mn{sub 2}CoGa thin films identified with x-ray magnetic linear dichroism: experiment and ab initio theory  

SciTech Connect (OSTI)

Epitaxial thin films of the half-metallic X{sub a}-compound Mn{sub 2}CoGa (Hg{sub 2}CuTi prototype) were prepared by dc magnetron co-sputtering with different heat treatments on MgO (001) substrates. High-quality #12;lms with a bulk magnetization of 1.95(5) {mu}{sub #22;}B per unit cell were obtained. The average Mn magnetic moment and the Co moment are parallel, in agreement with theory. The x-ray magnetic circular dichroism spectra agree with calculations based on density functional theory and reveal the antiparallel alignment of the two inequivalent Mn moments. X-ray magnetic linear dichroism allows to distinguish between itinerant and localized Mn moments. It is shown that one of the two Mn moments has localized character, whereas the other Mn moment and the Co moment are itinerant.

Meinert, M.; Schmalhorst, J; Klewe, C.; Reiss, G.; Arenholz, E.; Bohnert, T.; Nielsch, K.

2011-08-08T23:59:59.000Z

78

IMPROVEMENT OF CdMnTe DETECTOR PERFORMANCE BY MnTe PURIFICATION  

SciTech Connect (OSTI)

Residual impurities in manganese (Mn) are a big obstacle to obtaining high-performance CdMnTe (CMT) X-ray and gamma-ray detectors. Generally, the zone-refining method is an effective way to improve the material's purity. In this work, we purified the MnTe compounds combining the zone-refining method with molten Te, which has a very high solubility for most impurities. We confirmed the improved purity of the material by glow-discharge mass spectrometry (GDMS). We also found that CMT crystals from a multiply-refined MnTe source, grown by the vertical Bridgman method, yielded better performing detectors.

Kim, K.H.; Bolotnikov, A.E.; Camarda, G.S.; Tappero, R.; Hossain, A.; Cui, Y.; Yang, G.; Gul, R.; and James, R.B.

2011-04-25T23:59:59.000Z

79

LiMn{sub 2}O{sub 4} nanoparticles anchored on graphene nanosheets as high-performance cathode material for lithium-ion batteries  

SciTech Connect (OSTI)

Nanocrystalline LiMn{sub 2}O{sub 4}/graphene nanosheets nanocomposite has been successfully synthesized by a one-step hydrothermal method without post-heat treatment. In the nanocomposite, LiMn{sub 2}O{sub 4} nanoparticles of 10–30 nm in size are well crystallized and homogeneously anchored on the graphene nanosheets. The graphene nanosheets not only provide a highly conductive matrix for LiMn{sub 2}O{sub 4} nanoparticles but also effectively reduce the agglomeration of LiMn{sub 2}O{sub 4} nanoparticles. The nanocrystalline LiMn{sub 2}O{sub 4}/graphene nanosheets nanocomposite exhibited greatly improved electrochemical performance in terms of specific capacity, cycle performance, and rate capability compared with the bare LiMn{sub 2}O{sub 4} nanoparticles. The superior electrochemical performance of the nanocrystalline LiMn{sub 2}O{sub 4}/graphene nanosheets nanocomposite makes it promising as cathode material for high-performance lithium-ion batteries. - Graphical abstract: Nanocrystalline LiMn{sub 2}O{sub 4}/graphene nanosheets (GNS) nanocomposite exhibit superior cathode performance for lithium-ion batteries compared to the bare LiMn{sub 2}O{sub 4} nanoparticles. Display Omitted - Highlights: • LiMn{sub 2}O{sub 4}/graphene nanocomposite is synthesized by a one-step hydrothermal method. • LiMn{sub 2}O{sub 4} nanoparticles are uniformly anchored on the graphene nanosheets. • The nanocomposite exhibits excellent cathode performance for lithium-ion batteries.

Lin, Binghui; Yin, Qing; Hu, Hengrun; Lu, Fujia [School of Materials Science and Engineering, Nanjing University of Science and Technology, Xiaolingwei 200, Nanjing, Jiangsu 210094 (China); Xia, Hui, E-mail: xiahui@njust.edu.cn [School of Materials Science and Engineering, Nanjing University of Science and Technology, Xiaolingwei 200, Nanjing, Jiangsu 210094 (China); Herbert Gleiter Institute of Nanoscience, Nanjing University of Science and Technology, Nanjing 210094 (China)

2014-01-15T23:59:59.000Z

80

Mn/DOT County Road Safety Plans  

E-Print Network [OSTI]

Roads Program !! Minnesota Central Safety Funds !! Foster safety culture among county stakeholders 41 Mn/DOT County Road Safety Plans CTS Annual Research Conference April 27 & 28, 2010 Howard Preston & Objectives !! Project Overview !! Schedule, Participating Counties, Approach !! Safety Emphasis Areas

Minnesota, University of

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Helical antiferromagnetic ordering in Lu1-xScxMnSi  

SciTech Connect (OSTI)

Polycrystalline samples of Lu1?xScxMnSi (x=0, 0.25, 0.5) are studied using powder x-ray diffraction, heat capacity Cp, magnetization, magnetic susceptibility ?, and electrical resistivity ? measurements versus temperature T and magnetic field H. This system crystallizes in the primitive orthorhombic TiNiSi-type structure (space group Pnma) as previously reported. The ?(T) data indicate metallic behavior. The Cp(T), ?(T), and ?(T) measurements consistently indicate long-range antiferromagnetic (AF) transitions with AF ordering temperatures TN=246, 215, and 188 K for x=0, 0.25, and 0.5, respectively. A second transition is observed at somewhat lower T for each sample from the ?(T) and ?(T) measurements, which we speculate are due to spin reorientation transitions; these second transitions are completely suppressed in H=5.5 T. The Cp data below 10 K for each composition indicate an enhanced Sommerfeld electronic heat capacity coefficient for the series in the range ?=24–29 mJ/mol K2. The ?(T) measurements up to 1000 K were fitted by local-moment Curie-Weiss behaviors which indicate a low Mn spin S?1. The ? data below TN are analyzed using the Weiss molecular field theory for a planar noncollinear cycloidal AF structure with a composition-dependent pitch, following the previous neutron diffraction work of Venturini et al. [J. Alloys Compd. 256, 65 (1997)]. Within this model, the fits indicate a turn angle between Mn ordered moments along the cycloid axis of ?100? or ?145?, either of which indicate dominant AF interactions between the Mn spins in the Lu1?xScxMnSi series of compounds.

Goetsch, Ryan J [Ames Laboratory; Anand, V K [Ames Laboratory; Johnston, David C [Ames Laboratory

2014-08-01T23:59:59.000Z

82

RADIATION AND CLOUD MONITORING STATIONS  

E-Print Network [OSTI]

how they affect the energy balance between incoming solar radiation and heat re-radiated from Earth, and moisture content; area cloud coverage; solar and terrestrial radia- tion; and standard meteorological region and the North Slope of Alaska. ARCS sites are a component of the Department of Energy

Reeves, Geoffrey D.

83

High Mn austenitic stainless steel  

DOE Patents [OSTI]

An austenitic stainless steel alloy includes, in weight percent: >4 to 15 Mn; 8 to 15 Ni; 14 to 16 Cr; 2.4 to 3 Al; 0.4 to 1 total of at least one of Nb and Ta; 0.05 to 0.2 C; 0.01 to 0.02 B; no more than 0.3 of combined Ti+V; up to 3 Mo; up to 3 Co; up to 1W; up to 3 Cu; up to 1 Si; up to 0.05 P; up to 1 total of at least one of Y, La, Ce, Hf, and Zr; less than 0.05 N; and base Fe, wherein the weight percent Fe is greater than the weight percent Ni, and wherein the alloy forms an external continuous scale including alumina, nanometer scale sized particles distributed throughout the microstructure, the particles including at least one of NbC and TaC, and a stable essentially single phase FCC austenitic matrix microstructure that is essentially delta-ferrite-free and essentially BCC-phase-free.

Yamamoto, Yukinori (Oak Ridge, TN) [Oak Ridge, TN; Santella, Michael L (Knoxville, TN) [Knoxville, TN; Brady, Michael P (Oak Ridge, TN) [Oak Ridge, TN; Maziasz, Philip J (Oak Ridge, TN) [Oak Ridge, TN; Liu, Chain-tsuan (Knoxville, TN) [Knoxville, TN

2010-07-13T23:59:59.000Z

84

Hydrogen refueling station costs in Shanghai  

E-Print Network [OSTI]

total installed capital cost (TIC) 1% Of TIC 25% Estimate ofcost estimates for six station types SMR 100 a Equipment capital

Weinert, Jonathan X.; Shaojun, Liu; Ogden, Joan M; Jianxin, Ma

2007-01-01T23:59:59.000Z

85

Kansas Nuclear Profile - Wolf Creek Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

April 2012" "Next Release Date: February 2013" "Wolf Creek Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor...

86

Washington Nuclear Profile - Columbia Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

Columbia Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration...

87

Illinois Nuclear Profile - Dresden Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

Dresden Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration...

88

Illinois Nuclear Profile - Clinton Power Station  

U.S. Energy Information Administration (EIA) Indexed Site

Clinton Power Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration date"...

89

Illinois Nuclear Profile - Byron Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

Byron Generating Station" ,"Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration date"...

90

Massachusetts Nuclear Profile - Pilgrim Nuclear Power Station  

U.S. Energy Information Administration (EIA) Indexed Site

Pilgrim Nuclear Power Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer cpacity factor (percent)","Type","Commercial operation date","License...

91

Illinois Nuclear Profile - Braidwood Generation Station  

U.S. Energy Information Administration (EIA) Indexed Site

Braidwood Generation Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

92

Computational Optimization of Gas Compressor Stations: MINLP ...  

E-Print Network [OSTI]

Feb 26, 2015 ... Abstract: When considering cost-optimal operation of gas transport networks, compressor stations play the most important role. Proper ...

Daniel Rose

2015-02-26T23:59:59.000Z

93

Hydrogen Fueling Infrastructure Research and Station Technology...  

Energy Savers [EERE]

Infrastructure Research and Station Technology Download presentation slides from the DOE Fuel Cell Technologies Office webinar "An Overview of the Hydrogen Fueling Infrastructure...

94

Hydrogen refueling station costs in Shanghai  

E-Print Network [OSTI]

Fueling stations; Cost; Shanghai; Fuel cell vehicles 1.and the delivery cost for fuel cell vehicles, however, itthus hydrogen cost therefore depend on the ?eet of fuel cell

Weinert, Jonathan X.; Shaojun, Liu; Ogden, Joan M; Jianxin, Ma

2007-01-01T23:59:59.000Z

95

Microfabricated fuel heating value monitoring device  

DOE Patents [OSTI]

A microfabricated fuel heating value monitoring device comprises a microfabricated gas chromatography column in combination with a catalytic microcalorimeter. The microcalorimeter can comprise a reference thermal conductivity sensor to provide diagnostics and surety. Using microfabrication techniques, the device can be manufactured in production quantities at a low per-unit cost. The microfabricated fuel heating value monitoring device enables continuous calorimetric determination of the heating value of natural gas with a 1 minute analysis time and 1.5 minute cycle time using air as a carrier gas. This device has applications in remote natural gas mining stations, pipeline switching and metering stations, turbine generators, and other industrial user sites. For gas pipelines, the device can improve gas quality during transfer and blending, and provide accurate financial accounting. For industrial end users, the device can provide continuous feedback of physical gas properties to improve combustion efficiency during use.

Robinson, Alex L. (Albuquerque, NM); Manginell, Ronald P. (Albuquerque, NM); Moorman, Matthew W. (Albuquerque, NM)

2010-05-04T23:59:59.000Z

96

Heat collector  

DOE Patents [OSTI]

A heat collector and method suitable for efficiently and cheaply collecting solar and other thermal energy are provided. The collector employs a heat pipe in a gravity-assist mode and is not evacuated. The collector has many advantages, some of which include ease of assembly, reduced structural stresses on the heat pipe enclosure, and a low total materials cost requirement. Natural convective forces drive the collector, which after startup operates entirely passively due in part to differences in molecular weights of gaseous components within the collector.

Merrigan, Michael A. (Santa Cruz, NM)

1984-01-01T23:59:59.000Z

97

Heat collector  

DOE Patents [OSTI]

A heat collector and method suitable for efficiently and cheaply collecting solar and other thermal energy are provided. The collector employs a heat pipe in a gravity-assist mode and is not evacuated. The collector has many advantages, some of which include ease of assembly, reduced structural stresses on the heat pipe enclosure, and a low total materials cost requirement. Natural convective forces drive the collector, which after startup operates entirely passively due in part to differences in molecular weights of gaseous components within the collector.

Merrigan, M.A.

1981-06-29T23:59:59.000Z

98

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

4-12: Hydrogen Cost Comparison for Electrolysis Station WithAnalysis: Electrolysis, 30 kg/day, grid Hydrogen Cost ($/kg)the hydrogen costs from the HSCM for electrolysis stations

Lipman, T E; Weinert, Jonathan X.

2006-01-01T23:59:59.000Z

99

Corrosive resistant heat exchanger  

DOE Patents [OSTI]

A corrosive and errosive resistant heat exchanger which recovers heat from a contaminated heat stream. The heat exchanger utilizes a boundary layer of innocuous gas, which is continuously replenished, to protect the heat exchanger surface from the hot contaminated gas. The innocuous gas is conveyed through ducts or perforations in the heat exchanger wall. Heat from the heat stream is transferred by radiation to the heat exchanger wall. Heat is removed from the outer heat exchanger wall by a heat recovery medium.

Richlen, Scott L. (Annandale, VA)

1989-01-01T23:59:59.000Z

100

Evaluation of station blackout accidents at nuclear power plants: Technical findings related to unresolved safety issue A-44: Final report  

SciTech Connect (OSTI)

''Station Blackout,'' which is the complete loss of alternating current (AC) electrical power in a nuclear power plant, has been designated as Unresolved Safety Issue A-44. Because many safety systems required for reactor core decay heat removal and containment heat removal depend on AC power, the consequences of a station blackout could be severe. This report documents the findings of technical studies performed as part of the program to resolve this issue. The important factors analyzed include: the fequency of loss of offsite power; the probability that emergency or onsite AC power supplies would be unavailable; the capability and reliability of decay heat removal systems independent of AC power; and the likelihood that offsite power would be restored before systems that cannot operate for extended periods without AC power fail, thus resulting in core damage. This report also addresses effects of different designs, locations, and operational features on the estimated frequency of core damage resulting from station blackout events.

Not Available

1988-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Radiation-induced instability of MnS precipitates and its possible consequences on irradiation-induced stress corrosion cracking of austenitic stainless steels  

SciTech Connect (OSTI)

Irradiation-assisted stress corrosion cracking (IASCC) is a significant materials issue for the light water reactor (LWR) industry and may also pose a problem for fusion power reactors that will use water as coolant. A new metallurgical process is proposed that involves the radiation-induced release into solution of minor impurity elements not usually thought to participate in IASCC. MnS-type precipitates, which contain most of the sulfur in stainless steels, are thought to be unstable under irradiation. First, Mn transmutes strongly to Fe in thermalized neutron spectra. Second, cascade-induced disordering and the inverse Kirkendall effect operating at the incoherent interfaces of MnS precipitates are thought to act as a pump to export Mn from the precipitate into the alloy matrix. Both of these processes will most likely allow sulfur, which is known to exert a deleterious influence on intergranular cracking, to re-enter the matrix. To test this hypothesis, compositions of MnS-type precipitates contained in several unirradiated and irradiated heats of Type 304, 316, and 348 stainless steels (SSs) were analyzed by Auger electron spectroscopy. Evidence is presented that shows a progressive compositional modification of MnS precipitates as exposure to neutrons increases in boiling water reactors. As the fluence increases, the Mn level in MnS decreases, whereas the Fe level increases. The S level also decreases relative to the combined level of Mn and Fe. MnS precipitates were also found to be a reservoir of other deleterious impurities such as F and O which could be also released due to radiation-induced instability of the precipitates.

Chung, H.M.; Sanecki, J.E. [Argonne National Lab., IL (United States); Garner, F.A. [Pacific Northwest National Lab., Richland, WA (United States)

1996-12-01T23:59:59.000Z

102

(Hydrogen) Service Stations 101 Steven M. Schlasner  

E-Print Network [OSTI]

(Hydrogen) Service Stations 101 Steven M. Schlasner September 22, 2004 #12;2 DISCLAIMER Opinions · Comparison of Conventional with Hydrogen Fueling Stations · Hydrogen Fueling Life Cycle · Practical Design,000 retail outlets (350 company-owned) in 44 states · Brands: Conoco, Phillips 66, 76 · 32,800 miles pipeline

103

High speed imager test station  

DOE Patents [OSTI]

A test station enables the performance of a solid state imager (herein called a focal plane array or FPA) to be determined at high image frame rates. A programmable waveform generator is adapted to generate clock pulses at determinable rates for clock light-induced charges from a FPA. The FPA is mounted on an imager header board for placing the imager in operable proximity to level shifters for receiving the clock pulses and outputting pulses effective to clock charge from the pixels forming the FPA. Each of the clock level shifters is driven by leading and trailing edge portions of the clock pulses to reduce power dissipation in the FPA. Analog circuits receive output charge pulses clocked from the FPA pixels. The analog circuits condition the charge pulses to cancel noise in the pulses and to determine and hold a peak value of the charge for digitizing. A high speed digitizer receives the peak signal value and outputs a digital representation of each one of the charge pulses. A video system then displays an image associated with the digital representation of the output charge pulses clocked from the FPA. In one embodiment, the FPA image is formatted to a standard video format for display on conventional video equipment. 12 figs.

Yates, G.J.; Albright, K.L.; Turko, B.T.

1995-11-14T23:59:59.000Z

104

Energy absorption in Ni-Mn-Ga/ polymer composites  

E-Print Network [OSTI]

In recent years Ni-Mn-Ga has attracted considerable attention as a new kind of actuator material. Off-stoichiometric single crystals of Ni2MnGa can regularly exhibit 6% strain in tetragonal martensites and orthorhombic ...

Feuchtwanger, Jorge

2006-01-01T23:59:59.000Z

105

Heating System Specification Specification of Heating System  

E-Print Network [OSTI]

Appendix A Heating System Specification /* Specification of Heating System (loosely based */ requestHeat : Room ­? bool; 306 #12; APPENDIX A. HEATING SYSTEM SPECIFICATION 307 /* user inputs */ livingPattern : Room ­? behaviour; setTemp : Room ­? num; heatSwitchOn, heatSwitchOff, userReset : simple

Day, Nancy

106

Theory of weak localization in ferromagnetic (Ga,Mn)As  

E-Print Network [OSTI]

We study quantum interference corrections to the conductivity in (Ga,Mn)As ferromagnetic semiconductors using a model with disordered valence-band holes coupled to localized Mn moments through a p-d kinetic-exchange interaction. We find that at Mn...

Garate, Ion; Sinova, Jairo; Jungwirth, T.; MacDonald, A. H.

2009-01-01T23:59:59.000Z

107

Modelling Al and Mn in the open ocean  

E-Print Network [OSTI]

Modelling Al and Mn in the open ocean Marco van Hulten*, Alessandro Tagliabue, Jean-Claude Dutay van Hulten: Modelling Al and Mn in the open ocean 1 #12;Outline Introduction Model of aluminium Constraining dust flux Model of manganese Conclusions Marco van Hulten: Modelling Al and Mn in the open ocean 2

Haak, Hein

108

23rd steam-station cost survey  

SciTech Connect (OSTI)

The results of the 23rd Steam Station Cost Survey covering the year 1982 are summarized. The major categories of the survey are as follows: general data; output data, 1982; fuel consumption, 1982; operation 1982 (mills/net kWh); investment ($/net kWh); energy cost, 1982 (mills/net kWh); and station performance, 1982. Thirty-one fossil-fuel steam plants and four nuclear stations were included in the survey. Fuel and operating cost increases are felt to be responsible for the moderate rise in total busbar-enery costs. 11 figures, 1 table.

Friedlander, G.D.; Going, M.C.

1983-11-01T23:59:59.000Z

109

University Climatological Station Compiled by Erwin Wodarczak (1998)  

E-Print Network [OSTI]

University Climatological Station Committee fonds Compiled by Erwin Wodarczak (1998) #12;Fonds Description University Climatological Station Committee fonds. ­ 1961-1974. 3 cm of textual records. Administrative History In 1954 a President's Climatological Station Committee was established

Handy, Todd C.

110

A Near-Term Economic Analysis of Hydrogen Fueling Stations  

E-Print Network [OSTI]

0.07/kWh has on hydrogen cost for electrolysis type station.3-12: Hydrogen Cost Comparison for Electrolysis Station,3-12: Hydrogen Cost Comparison for Electrolysis Station, NAS

Weinert, Jonathan X.

2005-01-01T23:59:59.000Z

111

A Near-term Economic Analysis of Hydrogen Fueling Stations  

E-Print Network [OSTI]

0.07/kWh has on hydrogen cost for electrolysis type station.3-12: Hydrogen Cost Comparison for Electrolysis Station,3-12: Hydrogen Cost Comparison for Electrolysis Station, NAS

Weinert, Jonathan X.

2005-01-01T23:59:59.000Z

112

Renewable Energy Optimization Report for Naval Station Newport  

SciTech Connect (OSTI)

In 2008, the U.S. Environmental Protection Agency (EPA) launched the RE-Powering America's Land initiative to encourage the development of renewable energy (RE) on potentially contaminated land and mine sites. As part of this effort, EPA is collaborating with the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory (NREL) to evaluate RE options at Naval Station (NAVSTA) Newport in Newport, Rhode Island. NREL's Renewable Energy Optimization (REO) tool was utilized to identify RE technologies that present the best opportunity for life-cycle cost-effective implementation while also serving to reduce energy-related carbon dioxide emissions and increase the percentage of RE used at NAVSTA Newport. The technologies included in REO are daylighting, wind, solar ventilation preheating (SVP), solar water heating, photovoltaics (PV), solar thermal (heating and electric), and biomass (gasification and cogeneration). The optimal mix of RE technologies depends on several factors including RE resources; technology cost and performance; state, utility, and federal incentives; and economic parameters (discount and inflation rates). Each of these factors was considered in this analysis. Technologies not included in REO that were investigated separately per NAVSTA Newport request include biofuels from algae, tidal power, and ground source heat pumps (GSHP).

Robichaud, R.; Mosey, G.; Olis, D.

2012-02-01T23:59:59.000Z

113

MN4602 Crouch 2004 REASSESSING WEAPON SYSTEM  

E-Print Network [OSTI]

MN4602 Crouch 2004 REASSESSING WEAPON SYSTEM OPERATIONAL TEST & EVALUATION METHODOLOGIES LTC Thom support assessing a weapon systems true cost and performance characteristics? S1: Can/should cost, operational effectiveness and suitability be assessed independent of one another? S2: Do current test

114

"MBUF Demo" "Mn Road Fee Test"  

E-Print Network [OSTI]

(40 mpg) Electric Vehicle (non-gas powered) State Tax * Federal Tax ** State Tax * Federal Tax"MBUF Demo" "Mn Road Fee Test" "IntelliDrive Connected Vehicles for Safety, Mobility and User Fee Overview Six Months In-Vehicle Data Collection Participant Recruited Equipment Deployed First Odometer

Minnesota, University of

115

Mn/DOT's Project Peer Review  

E-Print Network [OSTI]

and sustain this culture #12;Project Management #12;Recent National Work in Transportation Project ManagementMn/DOT's Project Management Peer Review Creating a Project Management Culture 2010 CTS Research a Peer Review? Why Project Management? ·Improve project delivery performance ­ on time, on budget (an

Minnesota, University of

116

Hydrogen Fueling Station in Honolulu, Hawaii Feasibility Analysis...  

Broader source: Energy.gov (indexed) [DOE]

Station in Honolulu, Hawaii Feasibility Analysis Hydrogen Fueling Station in Honolulu, Hawaii Feasibility Analysis This feasibility report assesses the technical and economic...

117

EECBG Success Story: Police Station Triples Solar Power - and...  

Broader source: Energy.gov (indexed) [DOE]

Police Station Triples Solar Power - and Savings EECBG Success Story: Police Station Triples Solar Power - and Savings July 19, 2010 - 11:00am Addthis North Community Police...

118

Alternative Fueling Station Locator App Provides Info at Your...  

Broader source: Energy.gov (indexed) [DOE]

Fueling Station Locator website. It provides information on more than 15,000 public and private alternative fueling stations throughout the United States. The app lists where...

119

Pdc - The Worldwide Leader in Hydrogen Refueling Station Compression...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Pdc - The Worldwide Leader in Hydrogen Refueling Station Compression Pdc - The Worldwide Leader in Hydrogen Refueling Station Compression This presentation by Matther Weaver of Pdc...

120

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network [OSTI]

stations and vendors (e.g. Air Products and Chemicals, Inc,including Chevron and Air Products and Chemicals, Inc. , asDiesel a. Verified with Air Products representative, Feb

Weinert, Jonathan X.; Shaojun, Liu; Ogden, J; Jianxin, Ma

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

IntegratedScienceWorkingforYou Research Station  

E-Print Network [OSTI]

. . . . . . . . . . . . . . . . . . .5 Colorado's forest resources, 2002-2006 . . . . . . . . .6 Post Mountain Research Station Federal Recycling Program Printed on Recycled Paper The Rocky Mountain Research organi- zation--the most extensive natural resources research organization in the world. We maintain 14

122

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network [OSTI]

and the delivery cost for fuel cell vehicles, however, itfueling stations, cost, Shanghai, fuel cell vehicles 1.0hydrogen cost therefore depend on the fleet of fuel cell

Weinert, Jonathan X.; Shaojun, Liu; Ogden, J; Jianxin, Ma

2006-01-01T23:59:59.000Z

123

The College Station Residential Energy Compliance Code  

E-Print Network [OSTI]

The City of College Station, Texas adopted a new residential Energy Compliance Code in January, 1988. The code, which strengthens compliance requirements in several areas, has received broadly based support and acceptance from all major constituent...

Claridge, D. E.; Schrock, D.

1988-01-01T23:59:59.000Z

124

Field Station Contributors, 2010 Acton, Gary  

E-Print Network [OSTI]

Field Station Contributors, 2010 Acton, Gary Allen, Deborah and Harry Ardell, Robert and Lee Baker Mead, Judson and Jane Mead, Thomas and Lenore Merritt, Andrew and Eleanor Morganwalp, David and Jill

Polly, David

125

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network [OSTI]

Well-to-wheels analysis of hydrogen based fuel-cell vehicleJP, et al. Distributed Hydrogen Fueling Systems Analysis,”Year 2006 UCD—ITS—RR—06—04 Hydrogen Refueling Station Costs

Weinert, Jonathan X.; Shaojun, Liu; Ogden, Joan M; Jianxin, Ma

2006-01-01T23:59:59.000Z

126

Hydrogen Fueling Infrastructure Research and Station Technology  

Broader source: Energy.gov [DOE]

Presentation slides from the DOE Fuel Cell Technologies Office webinar "An Overview of the Hydrogen Fueling Infrastructure Research and Station Technology (H2FIRST) Project" held on November 18, 2014.

127

Repowering of the Midland Nuclear Station  

E-Print Network [OSTI]

REPOWERING OF THE MIDLAND NUCLEAR STATION C.E. Gatlin Jr. Gerald C. Velleroer Janes A. Mooney Manager of Projects Fluor Daniel, IrK::. Vice President Fluor Daniel, IrK::. Vice President Midlarrl eogneneration Venture Chicago, Illinois... Chicago, Illinois Midland, Michigan The conversion of the Midland Nuclear Station to a combined cycle power facility is the first of its kind. The eXisting nuclear steam turbine, combined with new, natural-gas-fired gas turbines, will create...

Gatlin, C. E. Jr.; Vellender, G. C.; Mooney, J. A.

128

Solar and Infrared Radiation Station (SIRS) Handbook  

SciTech Connect (OSTI)

The Solar Infrared Radiation Station (SIRS) provides continuous measurements of broadband shortwave (solar) and longwave (atmospheric or infrared) irradiances for downwelling and upwelling components. The following six irradiance measurements are collected from a network of stations to help determine the total radiative flux exchange within the Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) Climate Research Facility: • Direct normal shortwave (solar beam) • Diffuse horizontal shortwave (sky) • Global horizontal shortwave (total hemispheric) • Upwelling shortwave (reflected) • Downwelling longwave (atmospheric infrared) • Upwelling longwave (surface infrared)

Stoffel, T

2005-07-01T23:59:59.000Z

129

City of Allentown assessment of a district heating system  

SciTech Connect (OSTI)

The energy sources selected to accommodate the heat load consist of five 10 MWt units at the high temperature hot water generating station, ten 10 MWt units at the high temperature hot water generating station, and two 25 MWe (37.5 MWt) cogenerating fluidized bed combustion units at the incinerator site. The service area selected consists of the downtown commercial district. Total peak heat load for the forty seven block commercial district and twenty two industrial customers is estimated to be 187 MWt. The following aspects are covered: transmission and distribution piping systems, development strategy, capital costs and construction schedule, operation, economics, environmental analysis, and community impact.

Oliker, I.; Tamayne, T.

1982-09-01T23:59:59.000Z

130

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

vs. delivered hydrogen, compressor type, storage pressure).pump High-pressure hydrogen compressor Compressed hydrogenpipeline High-pressure hydrogen compressor Pipeline Station:

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

131

Calculations of Heat-Capacities of Adsorbates  

E-Print Network [OSTI]

PHYSICAL REVIEW B VOLUME 14, NUMBER 7 1 OCTOBER 1976 Calculations of heat capacities of adsorbates W. R. Lawrence and R. E. Allen Department of Physics, Texas A& M University, College Station, Texas 77843 (Received 2 September 1975) The phonon... the substrate has a perfect (100) surface and the adsorbate goes down as a solid monolayer in registry with the substrate. The quasiharmonic approximation was used, and the results for Ne adsorbates were considerably different from those obtained...

LAWRENCE, WR; Allen, Roland E.

1976-01-01T23:59:59.000Z

132

Geothermal heating  

SciTech Connect (OSTI)

The aim of the study is to demonstrate the viability of geothermal heating projects in energy and economic terms and to provide nomograms from which an initial estimate may be made without having to use data-processing facilities. The effect of flow rate and temperature of the geothermal water on drilling and on the network, and the effect of climate on the type of housing are considered.

Aureille, M.

1982-01-01T23:59:59.000Z

133

Heat pump system  

DOE Patents [OSTI]

An air heating and cooling system for a building includes an expansion-type refrigeration circuit and a heat engine. The refrigeration circuit includes two heat exchangers, one of which is communicated with a source of indoor air from the building and the other of which is communicated with a source of air from outside the building. The heat engine includes a heat rejection circuit having a source of rejected heat and a primary heat exchanger connected to the source of rejected heat. The heat rejection circuit also includes an evaporator in heat exchange relation with the primary heat exchanger, a heat engine indoor heat exchanger, and a heat engine outdoor heat exchanger. The indoor heat exchangers are disposed in series air flow relationship, with the heat engine indoor heat exchanger being disposed downstream from the refrigeration circuit indoor heat exchanger. The outdoor heat exchangers are also disposed in series air flow relationship, with the heat engine outdoor heat exchanger disposed downstream from the refrigeration circuit outdoor heat exchanger. A common fluid is used in both of the indoor heat exchanges and in both of the outdoor heat exchangers. In a first embodiment, the heat engine is a Rankine cycle engine. In a second embodiment, the heat engine is a non-Rankine cycle engine.

Swenson, Paul F. (Cleveland, OH); Moore, Paul B. (Fedhaurn, FL)

1982-01-01T23:59:59.000Z

134

Water and Space Heating Heat Pumps  

E-Print Network [OSTI]

This paper discusses the design and operation of the Trane Weathertron III Heat Pump Water Heating System and includes a comparison of features and performance to other domestic water heating systems. Domestic water is generally provided through...

Kessler, A. F.

1985-01-01T23:59:59.000Z

135

Industrial Waste Heat Recovery Using Heat Pipes  

E-Print Network [OSTI]

For almost a decade now, heat pipes with secondary finned surfaces have been utilized in counter flow heat exchangers to recover sensible energy from industrial exhaust gases. Over 3,000 such heat exchangers are now in service, recovering...

Ruch, M. A.

1981-01-01T23:59:59.000Z

136

Heating systems for heating subsurface formations  

DOE Patents [OSTI]

Methods and systems for heating a subsurface formation are described herein. A heating system for a subsurface formation includes a sealed conduit positioned in an opening in the formation and a heat source. The sealed conduit includes a heat transfer fluid. The heat source provides heat to a portion of the sealed conduit to change phase of the heat transfer fluid from a liquid to a vapor. The vapor in the sealed conduit rises in the sealed conduit, condenses to transfer heat to the formation and returns to the conduit portion as a liquid.

Nguyen, Scott Vinh (Houston, TX); Vinegar, Harold J. (Bellaire, TX)

2011-04-26T23:59:59.000Z

137

Hydrogen Fueling - Coming Soon to a Station Near You (Brochure)  

SciTech Connect (OSTI)

Fact sheet providing information useful to local permitting officials facing hydrogen fueling station proposals.

Not Available

2009-04-01T23:59:59.000Z

138

Station Processing for a Low Frequency Array in WA  

E-Print Network [OSTI]

for the remote station, minus 2 kW for cooling (considered "infrastructure"). #12;Station Processing Requirements stations (regardless of role as remote or core) (yes; remote stations can be "less" not "different") 2 (yes: 2-3 for core, 1 for remote) 6. Cost: TBD. (Prorated cost of ~US$500 per dual-pol element

Ellingson, Steven W.

139

The LOFAR Super Station concept : an input for discussion  

E-Print Network [OSTI]

throughout Europe : several stations in Germany1 , UK2 , soon a French LOFAR station in Nançay3 , and further contacts in several other countries4 FLOW context · Official decision for funding the French station taken MHz) o Incoherent addition of the same stations to synthesize a broad instantaneous beam (maximum

Demoulin, Pascal

140

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

station. H2Gen’s estimates for capital costs are also lowerestimates and show high variability (26%-117% of capital costs).capital costs of about $250,000. Existing hydrogen station cost analyses tend to under-estimate

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Heat exchanger  

DOE Patents [OSTI]

A heat exchanger comparising a shell attached at its open end to one side of a tube sheet and a detachable head connected to the other side of said tube sheet. The head is divided into a first and second chamber in fluid communication with a nozzle inlet and nozzle outlet, respectively, formed in said tube sheet. A tube bundle is mounted within said shell and is provided with inlets and outlets formed in said tube sheet in communication with said first and second chambers, respectively.

Brackenbury, P.J.

1983-12-08T23:59:59.000Z

142

Heat exchanger  

DOE Patents [OSTI]

A heat exchanger comparising a shell attached at its open end to one side of a tube sheet and a detachable head connected to the other side of said tube sheet. The head is divided into a first and second chamber in fluid communication with a nozzle inlet and nozzle outlet, respectively, formed in said tube sheet. A tube bundle is mounted within said shell and is provided with inlets and outlets formed in said tube sheet in communication with said first and second chambers, respectively.

Brackenbury, Phillip J. (Richland, WA)

1986-01-01T23:59:59.000Z

143

Larderello Geothermal Power Station | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429Lacey, Washington:Lakeville, MN) JumpLarderello Geothermal Area Jump

144

Hydrogen fueling station development and demonstration  

SciTech Connect (OSTI)

This is the final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). This project sought to develop and demonstrate a hydrogen fueling station for vehicles. Such stations are an essential infrastructural element in the practical application of hydrogen as vehicle fuel, and a number of issues such as safety, efficiency, design, and operating procedures can only be accurately addressed by a practical demonstration. Regardless of whether the vehicle is powered by an internal combustion engine or fuel cell, or whether the vehicle has a liquid or gaseous fuel tank, the fueling station is a critical technology that is the link between the local storage facility and the vehicle.

Edeskuty, F.J.; Daney, D.; Daugherty, M.; Hill, D.; Prenger, F.C.

1996-09-01T23:59:59.000Z

145

Economic Analysis of Hydrogen Energy Station Concepts: Are "H 2E-Stations" a Key Link to a Hydrogen Fuel Cell Vehicle Infrastructure?  

E-Print Network [OSTI]

in the analysis of hydrogen energy stations, additionalattractiveness of the hydrogen energy station scheme in bothECONOMIC ANALYSIS OF HYDROGEN ENERGY STATION CONCEPTS: ARE '

Lipman, Timothy E.; Edwards, Jennifer L.; Kammen, Daniel M.

2002-01-01T23:59:59.000Z

146

Pump station for radioactive waste water  

DOE Patents [OSTI]

A pump station for transferring radioactive particle containing waste water, includes: (a.) an enclosed sump having a vertically elongated right frusto conical wall surface and a bottom surface and (b.) a submersible volute centrifugal pump having a horizontally rotating impeller and a volute exterior surface. The sump interior surface, the bottom surface and the volute exterior surface are made of stainless steel having a 30 Ra or finer surface finish. A 15 Ra finish has been found to be most cost effective. The pump station is used for transferring waste water, without accumulation of radioactive fines.

Whitton, John P.; Klos, Dean M.; Carrara, Danny T.; Minno, John J.

2003-11-18T23:59:59.000Z

147

Dual source heat pump  

DOE Patents [OSTI]

What is disclosed is a heat pump apparatus for conditioning a fluid characterized by a fluid handler and path for circulating the fluid in heat exchange relationship with a refrigerant fluid; at least two refrigerant heat exchangers, one for effecting heat exchange with the fluid and a second for effecting heat exchange between refrigerant and a heat exchange fluid and the ambient air; a compressor for efficiently compressing the refrigerant; at least one throttling valve for throttling liquid refrigerant; a refrigerant circuit; refrigerant; a source of heat exchange fluid; heat exchange fluid circulating device and heat exchange fluid circuit for circulating the heat exchange fluid in heat exchange relationship with the refrigerant; and valves or switches for selecting the heat exchangers and direction of flow of the refrigerant therethrough for selecting a particular mode of operation. The heat exchange fluid provides energy for defrosting the second heat exchanger when operating in the air source mode and also provides a alternate source of heat.

Ecker, Amir L. (Dallas, TX); Pietsch, Joseph A. (Dallas, TX)

1982-01-01T23:59:59.000Z

148

Segmented heat exchanger  

DOE Patents [OSTI]

A segmented heat exchanger system for transferring heat energy from an exhaust fluid to a working fluid. The heat exchanger system may include a first heat exchanger for receiving incoming working fluid and the exhaust fluid. The working fluid and exhaust fluid may travel through at least a portion of the first heat exchanger in a parallel flow configuration. In addition, the heat exchanger system may include a second heat exchanger for receiving working fluid from the first heat exchanger and exhaust fluid from a third heat exchanger. The working fluid and exhaust fluid may travel through at least a portion of the second heat exchanger in a counter flow configuration. Furthermore, the heat exchanger system may include a third heat exchanger for receiving working fluid from the second heat exchanger and exhaust fluid from the first heat exchanger. The working fluid and exhaust fluid may travel through at least a portion of the third heat exchanger in a parallel flow configuration.

Baldwin, Darryl Dean (Lafayette, IN); Willi, Martin Leo (Dunlap, IL); Fiveland, Scott Byron (Metamara, IL); Timmons, Kristine Ann (Chillicothe, IL)

2010-12-14T23:59:59.000Z

149

Thermoelectric study of crossroads material MnTe via sulfur doping  

SciTech Connect (OSTI)

Here, we report thermoelectric study of crossroads material MnTe via iso-electronic doping S on the Te-site. MnTe{sub 1-x}S{sub x} samples with nominal S content of x?=?0.00, 0.05, and 0.10 were prepared using a melt-quench method followed by pulverization and spark plasma sintering. The X-ray powder diffraction, scanning electron microscopy, and ZAF-corrected compositional analysis confirmed that S uniformly substitutes Te up to slightly over 2%. A higher content of S in the starting materials led to the formation of secondary phases. The thermoelectric properties of MnTe{sub 1-x}S{sub x} samples were characterized by means of Seebeck coefficient, electrical conductivity, and thermal conductivity measurements from 300?K to 773?K. Furthermore, Hall coefficient measurements and a single parabolic band model were used to help gain insights on the effects of S-doping on the scattering mechanism and the carrier effective mass. As expected, S doping not only introduced hole charge carriers but also created short-range defects that effectively scatter heat-carrying phonons at elevated temperatures. On the other hand, we found that S doping degraded the effective mass. As a result, the ZT of MnTe{sub 0.9}S{sub 0.1} was substantially enhanced over the pristine sample near 400?K, while the improvement of ZT became marginal at elevated temperatures. A ZT???0.65 at 773?K was obtained in all three samples.

Xie, Wenjie, E-mail: xie@imw.uni-stuttgart.de; Populoh, Sascha; Sagarna, Leyre; Trottmann, Matthias [Empa–Swiss Federal Laboratories for Materials Science and Technology, Solid State Chemistry and Catalysis, Uberlandstrasse 129, CH-8600 Dübendorf (Switzerland); Ga??zka, Krzysztof [Empa–Swiss Federal Laboratories for Materials Science and Technology, Solid State Chemistry and Catalysis, Uberlandstrasse 129, CH-8600 Dübendorf (Switzerland); Department of Chemistry and Biochemistry, University of Bern, Freiestrasse 3, CH-3012 Bern (Switzerland); Xiao, Xingxing [Institute for Materials Science, University of Stuttgart, DE-70569 Stuttgart (Germany); Liu, Yufei; He, Jian [Department of Physics and Astronomy, Clemson University, Clemson, South Carolina 29634-0978 (United States); Weidenkaff, Anke [Empa–Swiss Federal Laboratories for Materials Science and Technology, Solid State Chemistry and Catalysis, Uberlandstrasse 129, CH-8600 Dübendorf (Switzerland); Institute for Materials Science, University of Stuttgart, DE-70569 Stuttgart (Germany)

2014-03-14T23:59:59.000Z

150

,"International Falls, MN Natural Gas Pipeline Imports From Canada...  

U.S. Energy Information Administration (EIA) Indexed Site

International Falls, MN Natural Gas Pipeline Imports From Canada (MMcf)" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of...

151

,"Noyes, MN Natural Gas Pipeline Imports From Canada (MMcf)"  

U.S. Energy Information Administration (EIA) Indexed Site

Imports From Canada (MMcf)" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of Series","Frequency","Latest Data for" ,"Data 1","Noyes, MN...

152

,"Warroad, MN Natural Gas Pipeline Imports From Canada (MMcf...  

U.S. Energy Information Administration (EIA) Indexed Site

Imports From Canada (MMcf)" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of Series","Frequency","Latest Data for" ,"Data 1","Warroad, MN...

153

On-Site Hydrogen Generation & Refueling Station  

E-Print Network [OSTI]

of FC vehicles under real-world conditions Cost analysis vs. target of $3/gge in 2008 On-site Auto Reforming based refueling station DOE Objectives Public education on hydrogen and fuel cells Evaluation cell & HCNG busses in commercial operation ­ Refueling fuel cell & HCNG street sweepers and cars

154

TARGET STATION INFRASTRUCTURE THE CNGS EXPERIENCE  

E-Print Network [OSTI]

of Aluminum Water cooled Current: 150kA (horn) ­ 180 kA (reflector) Pulse duration 7ms #12;Key elements Remote handling Remote station for radiation survey in the target chamber #12;CNGS Target Area I per cooling circuit 2007 run radiation effects on ventilation system electronics broken flexible stripline

McDonald, Kirk

155

HATCH PROJECT PROPOSAL OKLAHOMA AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

or Revised Project Procedures for initiating a new project or for revising an existing project entail: 1. Abstracting the essential features of the objective and procedures sections from the project outline for CRISHATCH PROJECT PROPOSAL OKLAHOMA AGRICULTURAL EXPERIMENT STATION USDA PROJECT OUTLINE DEVELOPMENT

Ghajar, Afshin J.

156

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION IN COOPERATION WITH THE MICHIGAN POTATO of Crop and Soil Sciences Michigan State University East Lansing, MI 48824 Cooperators: R.W. Chase, Ray INDUSTRY COMMISSION 2004 Michigan Potato Research Report Volume 36 Left to Right: Ben Kudwa, MPIC; Caryn

Douches, David S.

157

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION IN COOPERATION WITH THE MICHIGAN POTATO INDUSTRY COMMISSION MICHIGAN POTATO RESEARCH REPORT 2003 Volume 35 Click Here to Open the 2003 Potato, S. Cooper, L. Frank, J. Driscoll, and E. Estelle Department of Crop and Soil Sciences Michigan State

Douches, David S.

158

Michigan State University Agricultural Experiment Station  

E-Print Network [OSTI]

Michigan State University Agricultural Experiment Station In Cooperation with the Michigan Potato Department of Crop and Soil Sciences Michigan State University East Lansing, MI 48824 Cooperators: R.W. Chase At Michigan State University we are breeding potatoes for the chip-processing and tablestock markets

Douches, David S.

159

Michigan State University Agricultural Experiment Station  

E-Print Network [OSTI]

Michigan State University Agricultural Experiment Station In Cooperation with the Michigan Potato. Hammerschmidt and W. Kirk Departments of Crop and Soil Sciences and Plant Pathology Michigan State University potato selections from the Michigan State University and other potato breeding programs at the Montcalm

Douches, David S.

160

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION IN COOPERATION WITH THE MICHIGAN POTATO and W. Kirk Departments of Crop and Soil Sciences and Plant Pathology Michigan State University East selections from the Michigan State University and other potato breeding programs at the Montcalm Research

Douches, David S.

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION IN COOPERATION WITH THE MICHIGAN POTATO Sciences and Plant Pathology Michigan State University East Lansing, MI 48824 INTRODUCTION Each year we conduct a series of variety trials to assess advanced potato selections from the Michigan State University

Douches, David S.

162

Recent developments in HVDC convertor station design  

SciTech Connect (OSTI)

New requirements on HVDC convertor station performance have emerged during the past few years. The paper presents some of these requirements and shows how they have been met through equipment and system development. This development will result in a new generation of HVDC transmissions with still better performance than for the projects presently in operation.

Carlsson, L.

1984-08-01T23:59:59.000Z

163

CASE CRITICAL The Navajo Generating Station  

E-Print Network [OSTI]

Republic The Navajo Generating Station, the largest coal-fired power plant in the West, provides electrical discussions focusing on the environmental, social, and economic implications of high-stakes threats power to customers in three states and for the Central Arizona Project to pump Colorado River water

Hall, Sharon J.

164

NUMERICAL STUDY OF FLUID FLOW AND HEAT TRANSFER OVER A SERIES OF IN-LINE NONCIRCULAR  

E-Print Network [OSTI]

NUMERICAL STUDY OF FLUID FLOW AND HEAT TRANSFER OVER A SERIES OF IN-LINE NONCIRCULAR TUBES CONFINED, Texas A&M University, College Station, Texas, USA Two-dimensional steady developing fluid flow and heat-volume technique. Grid independence study was carried out by running the developed code for several different grid

Bahaidarah, Haitham M.

165

Unusual magnetic hysteresis and the weakened transition behavior induced by Sn substitution in Mn{sub 3}SbN  

SciTech Connect (OSTI)

Substitution of Sb with Sn was achieved in ferrimagnetic antiperovskite Mn{sub 3}SbN. The experimental results indicate that with an increase in Sn concentration, the magnetization continuously decreases and the crystal structure of Mn{sub 3}Sb{sub 1-x}Sn{sub x}N changes from tetragonal to cubic phase at around x of 0.8. In the doping series, step-like anomaly in the isothermal magnetization was found and this behavior was highlighted at x?=?0.4. The anomaly could be attributed to the magnetic frustration, resulting from competition between the multiple spin configurations in the antiperovskite lattice. Meantime, H{sub c} of 18 kOe was observed at x?=?0.3, which is probably the highest among those of manganese antiperovskite materials reported so far. With increasing Sn content, the abrupt change of resistivity and the sharp peak of heat capacity in Mn{sub 3}SbN were gradually weakened. The crystal structure refinements indicate the weakened change at the magnetic transition is close related to the change of c/a ratio variation from tetragonal to cubic with Sn content. The results derived from this study indicate that the behavior of Mn{sub 3}Sb{sub 1-x}Sn{sub x}N could potentially enhance its scientific and technical applications, such as spin torque transfer and hard magnets.

Sun, Ying, E-mail: sunying@buaa.edu.cn [Center for Condensed Matter and Materials Physics, Department of Physics, Beihang University, Beijing 100191 (China); International Center for Materials Nanoarchitectonics (WPI-MANA), National Institute for Materials Science, Tsukuba, Ibaraki 305-0044 (Japan); Guo, Yanfeng; Li, Jun; Wang, Xia [Superconducting Properties Unit, National Institute for Materials Science, Tsukuba, Ibaraki 305-0044 (Japan); Tsujimoto, Yoshihiro [Materials Processing Unit, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047 (Japan); Wang, Cong [Center for Condensed Matter and Materials Physics, Department of Physics, Beihang University, Beijing 100191 (China); Feng, Hai L.; Sathish, Clastin I.; Yamaura, Kazunari, E-mail: yamaura.kazunari@nims.go.jp [Superconducting Properties Unit, National Institute for Materials Science, Tsukuba, Ibaraki 305-0044 (Japan); Graduate School of Chemical Sciences and Engineering, Hokkaido University, Sapporo, Hokkaido 060-0810 (Japan); Matsushita, Yoshitaka [Analysis Station, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047 (Japan)

2014-01-28T23:59:59.000Z

166

Abundance and distribution of macro-crustaceans in the intake and discharge areas before and during early operation of the Cedar Bayou Generating Station  

E-Print Network [OSTI]

and Discharge Areas Before and During Early Operation of the Cedar Bayou Generating Station. (May 1972) Monroe Schmidt, A. A. , Blinn College; B. S. , Texas A&M University Directed by: Dr. Kirk Strawn Two trawl and 1 seine station in Tabbs Bay, 2 trawl... were collected twice monthly from May through October 1970. Genera- tion of electric power (and discharge of heated water) by Unit 1, a 750 MW steam-electric unit of the Houston Lighting and Power Company's Cedar Bayou Generating Station, began...

Schmidt, Monroe

1972-01-01T23:59:59.000Z

167

Alignment of micro-crystals of Mn12-acetate and direct observation of single molecules thereof  

E-Print Network [OSTI]

This dissertation focuses on three separate studies. First, magnetization of the Mn12- acetate was studied by low temperature hysteresis loops and DC magnetization data on magnetically aligned Mn12-acetate micro-crystals. Secondly, Mn12-acetate thin...

Seo, Dongmin

2009-05-15T23:59:59.000Z

168

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

Installed Capital Figure 4-21: Cost Estimates for 1,000 kg/station. H2Gen’s estimates for capital costs are also lowerestimates and show high variability (26%-117% of capital costs).

Lipman, T E; Weinert, Jonathan X.

2006-01-01T23:59:59.000Z

169

Multiple source heat pump  

DOE Patents [OSTI]

A heat pump apparatus for conditioning a fluid characterized by a fluid handler and path for circulating a fluid in heat exchange relationship with a refrigerant fluid, at least three refrigerant heat exchangers, one for effecting heat exchange with the fluid, a second for effecting heat exchange with a heat exchange fluid, and a third for effecting heat exchange with ambient air; a compressor for compressing the refrigerant; at least one throttling valve connected at the inlet side of a heat exchanger in which liquid refrigerant is vaporized; a refrigerant circuit; refrigerant; a source of heat exchange fluid; heat exchange fluid circuit and pump for circulating the heat exchange fluid in heat exchange relationship with the refrigerant; and valves or switches for selecting the heat exchangers and directional flow of refrigerant therethrough for selecting a particular mode of operation. Also disclosed are a variety of embodiments, modes of operation, and schematics therefor.

Ecker, Amir L. (Duncanville, TX)

1983-01-01T23:59:59.000Z

170

Minnesota Guidestar www.dot.state.mn.us/guidestar  

E-Print Network [OSTI]

.dot.state.mn.us/guidestar What is ITS? · Application of technology to improve the safety and efficiency of the transportation system. #12;Minnesota Guidestar www.dot.state.mn.us/guidestar What is ITS? · Traffic Management ­ Signal Systems ­ Ramp Meters · Emergency Response ­ Mobile Data Terminals ­ 911 Dispatch ­ RF Data Networks

Minnesota, University of

171

Thermal Stability of MnBi Magnetic Materials  

SciTech Connect (OSTI)

MnBi attracts great attention in recent years for its great potential as permanent magnet materials. It is unique because its coercivity increases with increasing temperature, which makes it a good hard phase for exchange coupling nanocomposite magnet. MnBi phase is difficult to obtain, partly because the reaction between Mn and Bi is peritectic, and partly because Mn is easy to react with oxygen. MnO formation is irreversible and causes degradation to the magnetic properties. In this paper, we report our effort on developing MnBi permanent magnet. High purity MnBi (>90%) can be routinely produced in large quantity. The obtained powder exhibit 74 emu/g saturation magnetization at room temperature with 9 T applied field. After alignment, the powder exhibits 11.6 MGOe, and the sintered bulk magnet exhibit 7.8 MGOe at room temperature. Thermal stability study shows that the MnBi is stable up to 473 K in air.

Cui, Jun; Choi, Jung-Pyung; Li, Guosheng; Polikarpov, Evgueni; Darsell, Jens T.; Overman, Nicole R.; Olszta, Matthew J.; Schreiber, Daniel K.; Bowden, Mark E.; Droubay, Timothy C.; Kramer, Matthew J.; Zarkevich, Nikolai; Wang, L. L.; Johnson, Duane D.; Marinescu, Melania; Takeuchi, Ichiro; Huang, Qingzhen; Wu, Hui; Reeve, Hayden; Vuong, Nguyen V.; Liu, J.Ping

2014-01-01T23:59:59.000Z

172

Thermal stability of MnBi magnetic materials  

SciTech Connect (OSTI)

MnBi has attracted much attention in recent years due to its potential as a rare-earth-free permanent magnet material. It is unique because its coercivity increases with increasing temperature, which makes it a good hard phase material for exchange coupling nanocomposite magnets. MnBi phase is difficult to obtain, partly because the reaction between Mn and Bi is peritectic, and partly because Mn reacts readily with oxygen. MnO formation is irreversible and harmful to magnet performance. In this paper, we report our efforts toward developing MnBi permanent magnets. To date, high purity MnBi (>90%) can be routinely produced in large quantities. The produced powder exhibits 74:6 emu g1 saturation magnetization at room temperature with 9 T applied field. After proper alignment, the maximum energy product (BH) max of the powder reached 11.9 MGOe, and that of the sintered bulk magnet reached 7.8 MGOe at room temperature. A comprehensive study of thermal stability shows that MnBi powder is stable up to 473 K in air.

Cui, Jinfang [Pacific Northwest National Laboratory; Choi, J. P. [Pacific Northwest National Laboratory; Li, G. [Pacific Northwest National Laboratory; Polikarpov, E. [Pacific Northwest National Laboratory; Darsell, J. [Pacific Northwest National Laboratory; Overman, N. [Pacific Northwest National Laboratory; Olszta, M. [Pacific Northwest National Laboratory; Schreiber, D. [Pacific Northwest National Laboratory; Bowden, M. [Environmental Molecular Sciences Laboratory; Droubay, T. [Pacific Northwest National Laboratory; Kramer, Matthew J. [Ames Laboratory; Zarkevich, Nikolay A. [Ames Laboratory; Wang, L L. [Ames Laboratory; Johnson, Duane D. [Ames Laboratory; Marinescu, M. [Electron Energy Corporation; Takeuchi, I. [University of Maryland; Huang, Q. Z. [National Institute of Standards and Technology; Wu, H. [University of Maryland; Reeve, H. [United Technologies Research Center; Vuong, N. V. [University of Texas; Liu, J P. [University of Texas

2014-01-27T23:59:59.000Z

173

Heat Pump for High School Heat Recovery  

E-Print Network [OSTI]

The heat pump system used for recycling and reusing waste heat in s high school bathroom was minutely analyzed in its coefficient of performance, onetime utilization ratio of energy, economic property and so on. The results showed that this system...

Huang, K.; Wang, H.; Zhou, X.

2006-01-01T23:59:59.000Z

174

Fact #816: February 10, 2014 Natural Gas Refueling Stations Grow...  

Broader source: Energy.gov (indexed) [DOE]

6: February 10, 2014 Natural Gas Refueling Stations Grow Over the Last Ten Years Fact 816: February 10, 2014 Natural Gas Refueling Stations Grow Over the Last Ten Years In 2003...

175

Geothermal system saving money at fire station | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Geothermal system saving money at fire station Geothermal system saving money at fire station April 9, 2010 - 3:45pm Addthis Joshua DeLung What will the project do? A geothermal...

176

Spectroscopy of Mn atoms isolated in solid {sup 4}He  

SciTech Connect (OSTI)

We present an experimental study of the laser-induced luminescence spectra of Mn atoms in solid helium matrices. We observe transitions of the valence electron and of inner-shell electrons. We find that the Mn-He interaction perturbs the inner-shell transitions to a lesser extent than the valence-electron transitions. The observed lineshapes of the inner-shell transitions of Mn are similar to those of an inner-shell transition in Ba studied earlier. At the same time, they are more strongly perturbed than the corresponding transitions in Au and Cu under the same conditions. We suggest a qualitative explanation of these observations based on the atomic bubble model. Our results also suggest that the inner-shell transitions of Mn in solid He are more strongly perturbed than the same lines of Mn isolated in solid Ar or Kr matrices.

Moroshkin, P., E-mail: petr.moroshkin@riken.jp; Lebedev, V.; Weis, A. [Department of Physics, University of Fribourg, Chemin du Musée 3, 1700 Fribourg (Switzerland)

2014-06-07T23:59:59.000Z

177

Magnetic Moment Enhancement for Mn7 Cluster on Graphene  

SciTech Connect (OSTI)

Mn7 cluster on graphene with different structural motifs and magnetic orders are investigated systematically by first-principles calculations. The calculations show that Mn7 on graphene prefers a two-layer motif and exhibits a ferrimagnetic coupling. The magnetic moment of the Mn7 cluster increases from 5.0 ?B at its free-standing state to about 6.0 ?B upon adsorption on graphene. Mn7 cluster also induces about 0.3 ?B of magnetic moment in the graphene layer, leading to an overall enhancement of 1.3 ?B magnetic moment for Mn7 on graphene. Detail electron transfer and bonding analysis have been carried out to investigate the origin of the magnetic enhancement.

Liu, Xiaojie [Ames Laboratory; Wang, Cai-Zhuang [Ames Laboratory; Lin, Hai-Qing [Beijing Computational Science Research Center; Ho, Kai-Ming [Ames Laboratory

2014-08-21T23:59:59.000Z

178

The helium abundances in HgMn and normal stars  

E-Print Network [OSTI]

The parameter-free model of diffusion in the atmospheres of HgMn stars (Michaud 1986; Michaud et al 1979) predicts that helium should sink below the He II ionization zone in order that diffusion of other elements may take place, and that all HgMn stars should have deficits of helium in their photospheres, with a minimum deficit of 0.3 dex. In this study, the Smith & Dworetsky (1993) sample of HgMn stars and normal comparison stars is examined, and the helium abundances determined by spectrum synthesis using echelle spectra taken at Lick Observatory and the AAT. The prediction is confirmed; all HgMn stars are deficient in He by as much as 1.5 dex. Also, two HgMn stars, HR7361 and HR7664, show clear evidence of helium stratification.

M. M. Dworetsky

2004-07-26T23:59:59.000Z

179

Combined Heat and Power, Waste Heat, and District Energy | Department...  

Broader source: Energy.gov (indexed) [DOE]

Combined Heat and Power, Waste Heat, and District Energy Combined Heat and Power, Waste Heat, and District Energy Presentation-given at the Fall 2011 Federal Utility Partnership...

180

Project Profile: Heat Transfer and Latent Heat Storage in Inorganic...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Heat Transfer and Latent Heat Storage in Inorganic Molten Salts for CSP Plants Project Profile: Heat Transfer and Latent Heat Storage in Inorganic Molten Salts for CSP Plants...

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Pagosa Springs District Heating District Heating Low Temperature...  

Open Energy Info (EERE)

Pagosa Springs District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Pagosa Springs District Heating District Heating Low...

182

Kethcum District Heating District Heating Low Temperature Geothermal...  

Open Energy Info (EERE)

Kethcum District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Kethcum District Heating District Heating Low Temperature Geothermal...

183

Midland District Heating District Heating Low Temperature Geothermal...  

Open Energy Info (EERE)

Midland District Heating District Heating Low Temperature Geothermal Facility Facility Midland District Heating Sector Geothermal energy Type District Heating Location Midland,...

184

San Bernardino District Heating District Heating Low Temperature...  

Open Energy Info (EERE)

San Bernardino District Heating District Heating Low Temperature Geothermal Facility Facility San Bernardino District Heating Sector Geothermal energy Type District Heating...

185

Philip District Heating District Heating Low Temperature Geothermal...  

Open Energy Info (EERE)

Philip District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Philip District Heating District Heating Low Temperature Geothermal...

186

Absorption heat pump system  

DOE Patents [OSTI]

The efficiency of an absorption heat pump system is improved by conducting liquid from a second stage evaporator thereof to an auxiliary heat exchanger positioned downstream of a primary heat exchanger in the desorber of the system.

Grossman, G.

1982-06-16T23:59:59.000Z

187

Locating Heat Recovery Opportunities  

E-Print Network [OSTI]

Basic concepts of heat recovery are defined as they apply to the industrial community. Methods for locating, ranking, and developing heat recovery opportunities are presented and explained. The needs for useful heat 'sinks' are emphasized as equal...

Waterland, A. F.

1981-01-01T23:59:59.000Z

188

Absorption heat pump system  

DOE Patents [OSTI]

The efficiency of an absorption heat pump system is improved by conducting liquid from a second stage evaporator thereof to an auxiliary heat exchanger positioned downstream of a primary heat exchanger in the desorber of the system.

Grossman, Gershon (Oak Ridge, TN)

1984-01-01T23:59:59.000Z

189

Small SDI battle stations - More is better  

SciTech Connect (OSTI)

It is presently suggested that large numbers of lower capability SDI systems, in contrast to small numbers of large battle stations, offer better overall defense performance at lower total cost, with lower technical risk, lower sensitivity to threat scenario variability, and improved survivability. This follows from such factors as the positioning of more platforms within effective range of targets during all phases of an attack, less exacting optics requirements, mass production economies-of-scale, and improved survivability.

Cornet, E.

1986-09-01T23:59:59.000Z

190

Improving Unit Operations-Test Station Performance  

E-Print Network [OSTI]

IMPROVING UNIT OPERATIONS - TEST STATION PERFORMANCE JosqIb 1. Filak. Jr, ? Corporate Energy Manager. Park.er?Hannafin COfpontioo- Cleveland. Oh ABSTRACT: This program's basic concept deals with the possibilities for reducing energy efficiency... requirements, control operation test performance functions more successfully, and retain peak load surges from reaching higher utility rate expense levels. 142 ESL-IE-95-04-23 Proceedings from the Seventeenth Industrial Energy Technology Conference...

Filak, J. J. Jr.

191

Xcel Energy Comanche Station: Pueblo, Colorado (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

A partnership with industry and U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to collect solar data to support future solar power generation in the United States. The measurement station monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location. The solar measurement instrumentation is also accompanied by meteorological monitoring equipment to provide scientists with a complete picture of the solar power possibilities.

Stoffel, T.; Andreas, A.

192

Manuel pour installer une station sismologique OSIRIS  

E-Print Network [OSTI]

installation Tout d'abord, enterrer le sismom`etre, s'assurer de l'horizontalit´e du sismo c'est-`a-dire, bulle le c^able sur le sismo, v´erifier de nouveau l'horizontalit´e. GPS Batterie ` Station d "sismo" puis cd osiris puis ./nrtd -set eth0 #12;7- Lancer Firefox (web browser) depuis la barre de menu

Perrot, Julie

193

Formation of MnSb during the growth of MnSi layers in the presence of an Sb flux  

E-Print Network [OSTI]

, Kawasaki 210-0855, Japan Y. Yan National Renewable Energy Laboratory, Golden, Colorado 80401 S. J a magnetic transition at TC 29.1 K from a paramag- netic state to a helicoidal order.3 An itinerant metamagnetic transition in MnSi has been observed,4,5 and magnetic prop- erties of MnSi under high pressure

Pennycook, Steve

194

Woven heat exchanger  

DOE Patents [OSTI]

This invention relates to a heat exchanger for waste heat recovery from high temperature industrial exhaust streams. In a woven ceramic heat exchanger using the basic tube-in-shell design, each heat exchanger consisting of tube sheets and tube, is woven separately. Individual heat exchangers are assembled in cross-flow configuration. Each heat exchanger is woven from high temperature ceramic fiber, the warp is continuous from tube to tube sheet providing a smooth transition and unitized construction.

Piscitella, R.R.

1984-07-16T23:59:59.000Z

195

Competitive Charging Station Pricing for Plug-in Electric Vehicles  

E-Print Network [OSTI]

. To overcome this challenge, we develop a low-complexity algorithm that efficiently computes the pricingCompetitive Charging Station Pricing for Plug-in Electric Vehicles Wei Yuan, Member, IEEE, Jianwei considers the problem of charging station pricing and station selection of plug-in electric vehicles (PEVs

Huang, Jianwei

196

"Space Station" Theme: Learning to Work, and Live, in Space  

E-Print Network [OSTI]

"Space Station" IMAX Film Theme: Learning to Work, and Live, in Space The educational value of NASM visit and afterward. See the "Alignment with Standards" table for details regarding how "Space Station in the "Space Station" program: · How astronauts train · What it is like to live and work in Space aboard

Mathis, Wayne N.

197

Optimization of compression and storage requirements at hydrogen refueling stations.  

SciTech Connect (OSTI)

The transition to hydrogen-powered vehicles requires detailed technical and economic analyses of all aspects of hydrogen infrastructure, including refueling stations. The cost of such stations is a major contributor to the delivered cost of hydrogen. Hydrogen refueling stations require not only dispensers to transfer fuel onto a vehicle, but also an array of such ancillary equipment as a cascade charging system, storage vessels, compressors and/or pumps/evaporators. This paper provides detailed information on design requirements for gaseous and liquid hydrogen refueling stations and their associated capital and operating costs, which in turn impact hydrogen selling price at various levels of hydrogen demand. It summarizes an engineering economics approach which captures the effect of variations in station size, seasonal, daily and hourly demand, and alternative dispensing rates and pressures on station cost. Tradeoffs in the capacity of refueling station compressors, storage vessels, and the cascade charging system result in many possible configurations for the station. Total costs can be minimized by optimizing that configuration. Using a methodology to iterate among the costs of compression, storage and cascade charging, it was found that the optimum hourly capacity of the compressor is approximately twice the station's average hourly demand, and the optimum capacity of the cascade charging system is approximately 15% of the station's average daily demand. Further, for an hourly demand profile typical of today's gasoline stations, onsite hydrogen storage equivalent to at least 1/3 of the station's average daily demand is needed to accommodate peak demand.

Elgowainy, A.; Mintz, M.; Kelly, B.; Hooks, M.; Paster, M. (Energy Systems); (Nexant, Inc.); (TIAX LLC)

2008-01-01T23:59:59.000Z

198

Chemical and structural investigation of the role of both Mn and Mn oxide in the formation of manganese silicate barrier layers on SiO{sub 2}  

SciTech Connect (OSTI)

In this study, Mn silicate (MnSiO{sub 3}) barrier layers were formed on thermally grown SiO{sub 2} using both metallic Mn and oxidized Mn films, in order to investigate the role of oxygen in determining the extent of the interaction between the deposited Mn and the SiO{sub 2} substrate. Using x-ray photoelectron spectroscopy, it has been shown that a metallic Mn film with an approximate thickness of 1 nm cannot be fully converted to Mn silicate following vacuum annealing to 500 deg. C. Transmission electron microscopy (TEM) analysis suggests the maximum MnSiO{sub 3} layer thickness obtainable using metallic Mn is {approx}1.7 nm. In contrast, a {approx}1 nm partially oxidized Mn film can be fully converted to Mn silicate following thermal annealing to 400 deg. C, forming a MnSiO{sub 3} layer with a measured thickness of 2.6 nm. TEM analysis also clearly shows that MnSiO{sub 3} growth results in a corresponding reduction in the SiO{sub 2} layer thickness. It has also been shown that a fully oxidized Mn oxide thin film can be converted to Mn silicate, in the absence of metallic Mn. Based on these results it is suggested that the presence of Mn oxide species at the Mn/SiO{sub 2} interface facilitates the conversion of SiO{sub 2} to MnSiO{sub 3}, in agreement with previously published studies.

Casey, P.; Bogan, J.; Hughes, G. [School of Physical Sciences, Dublin City University, Glasnevin, Dublin 9 (Ireland); Lozano, J. G.; Nellist, P. D. [Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH (United Kingdom)

2011-09-01T23:59:59.000Z

199

Plug-In Electric Vehicle Handbook for Public Charging Station Hosts (Brochure)  

SciTech Connect (OSTI)

This handbook answers basic questions about plug-in electric vehicles, charging stations, charging equipment, and considerations for station owners, property owners, and station hosts.

Not Available

2012-04-01T23:59:59.000Z

200

Comparison of Idealized and Real-World City Station Citing Models for Hydrogen Distribution  

E-Print Network [OSTI]

city size, and gasoline station locations. By characterizingfuel than typical gasoline stations. As a result, it will bestreet networks and gasoline stations for (a) Sacramento (b)

Yang, Christopher; Nicholas, Michael A; Ogden, Joan M

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Refueling Availability for Alternative Fuel Vehicle Markets: Sufficient Urban Station Coverage  

E-Print Network [OSTI]

ed Basin Dataset on Urban Gasoline Stations. Institute ofavailability Gasoline stations abstract Alternative fueldistribution, the existing gasoline station networks in many

Melaina, Marc W; Bremson, Joel

2008-01-01T23:59:59.000Z

202

E-Print Network 3.0 - arctowski station king Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

HoytSt Burnett... Front Stadium Broad St Station Military Park Rutgers University Essex County College PASSAIC RIVER BROAD ST... STATION Route 280 Pennsylvania RailroadStation...

203

Thermodynamic and transport properties of single-crystal Yb{sub 14}MnSb{sub 11}  

SciTech Connect (OSTI)

Relatively large (up to 250 mg) single crystals of the intermetallic compound Yb{sub 14}MnSb{sub 11} have been prepared by a flux-growth technique. The results of thermodynamic and transport measurements of these samples are presented. The compound orders ferromagnetically at approximately T{sub C}=53{plus_minus}1K, with a magnetization consistent with the assignment Mn{sup 3+} (3d{sup 4}) and Yb{sup 2+} (4f{sup 14}). The Mn moments are local in nature, with the full effective and saturated moment of the Hund{close_quote}s rule spin-only ground state. The electrical resistivity has a metallic temperature dependence, with only a modest anisotropy. Room-temperature values of the resistivity are relatively high for an intermetallic compound: 1630{plus_minus}160 {mu}{Omega}cm and 1250{plus_minus}130 {mu}{Omega}cm for currents flowing approximately parallel and perpendicular to the {ital c} axis, respectively. There is a distinct loss of spin-disorder scattering in the resistivity at T{sub C}. From the heat capacity, a rough estimation of the magnetic entropy gives {Delta}S{sub M}{approx}12.1 J/mol K, the value in reasonable agreement with the expected {Delta}S{sub M}{approx}R ln 5 from the assignment of these moments. All of these data are consistent with a picture of Mn{sup 3+} local moments being coupled via conduction electrons. To this end, Yb{sub 14}MnSb{sub 11} appears to be analogous to local-moment rare-earth intermetallic compounds, and may point the way toward a class of 3d Kondo lattice compounds. {copyright} {ital 1999} {ital The American Physical Society}

Fisher, I.R.; Wiener, T.A.; Budko, S.L.; Canfield, P.C. [Ames Laboratory and Department of Physics and Astronomy, Iowa State University, Ames, Iowa 50011 (United States)] [Ames Laboratory and Department of Physics and Astronomy, Iowa State University, Ames, Iowa 50011 (United States); Chan, J.Y.; Kauzlarich, S.M. [Department of Chemistry, One Shields Avenue, University of California, Davis, California 95616 (United States)] [Department of Chemistry, One Shields Avenue, University of California, Davis, California 95616 (United States)

1999-06-01T23:59:59.000Z

204

Facile synthesis of {alpha}-MnO{sub 2} one-dimensional (1D) nanostructure and energy storage ability studies  

SciTech Connect (OSTI)

The dense manganese oxide nanorods with an extremely narrow distribution are synthesized at a low temperature using first cathodic electrodeposition subsequently heat treatment. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images show that the nanorods have bar shapes, and their average diameter is less than 50 nm. The Fourier transform infrared (FT-IR) study, the selected area electron diffraction (SAED) pattern in TEM images and the X-ray diffraction (XRD) result show that the nanorods are {alpha}-MnO{sub 2} single crystal. The results of N{sub 2} adsorption-desorption analysis indicate that the BET surface area of the {alpha}-MnO{sub 2} nanorods is 93 m{sup 2} g{sup -1}. By recording the potential-time curve during the electrodeposition process, it is revealed that water reduction reaction has a major role in the electrogeneration of base at the cathode surface under the applied electrochemical conditions. Finally, based on the H{sub 2} bubbling on the cathode surface, the mechanism of the formation and the growth of {alpha}-MnO{sub 2} nanorods are proposed and discussed. For the electrochemical supercapacitor application, electrochemically prepared {alpha}-MnO{sub 2} is found to be stable for a large number of cycles with high specific capacitance, 338 F g{sup -1} at a scan rate of 10 mV s{sup -1}. Finally, the charge-discharge mechanism is discussed. - Graphical abstract: Highlights: Black-Right-Pointing-Pointer New nanostructures of MnO{sub 2} is synthesized by simple method of cathodicelectrodeposition. Black-Right-Pointing-Pointer The product has unique one-dimensional morphology with average diameter size of 50 nm. Black-Right-Pointing-Pointer The experiment conditions (temperature, current density) has not been reported. Black-Right-Pointing-Pointer The one-nanostructures obtained without using of hard template or surfactant.

Yousefi, Taher, E-mail: anozadg@yahoo.com [Department of Chemistry, Tarbiat Moallem University, PO Box: 31979-37551, Tehran (Iran, Islamic Republic of); Materials Research School, NSTRI, PO Box: 14395-836, Tehran (Iran, Islamic Republic of); Golikand, Ahmad Nozad, E-mail: taher_yosefy@yahoo.com [Materials Research School, NSTRI, PO Box: 14395-836, Tehran (Iran, Islamic Republic of); Hossein Mashhadizadeh, Mohammad [Department of Chemistry, Tarbiat Moallem University, PO Box: 31979-37551, Tehran (Iran, Islamic Republic of); Aghazadeh, Mustafa [Department of Optic and Spectroscopy, Lasers and Optics Research School, NSTRI, PO Box: 11365-8486, Tehran (Iran, Islamic Republic of)

2012-06-15T23:59:59.000Z

205

Total Space Heat-  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

Commercial Buildings Energy Consumption Survey: Energy End-Use Consumption Tables Total Space Heat- ing Cool- ing Venti- lation Water Heat- ing Light- ing Cook- ing Refrig- eration...

206

Total Space Heat-  

Gasoline and Diesel Fuel Update (EIA)

Revised: December, 2008 Total Space Heat- ing Cool- ing Venti- lation Water Heat- ing Light- ing Cook- ing Refrig- eration Office Equip- ment Com- puters Other All Buildings...

207

Towards Intelligent District Heating.  

E-Print Network [OSTI]

??A district heating system consists of one or more production units supplying energy in the form of heated water through a distribution pipe network to… (more)

Johansson, Christian

2010-01-01T23:59:59.000Z

208

Winter Heating Fuels Update  

Gasoline and Diesel Fuel Update (EIA)

Heating Fuels Update For: Congressional Briefings October 20, 2014 | Washington, DC By U.S. Energy Information Administration Winter Heating Fuels Update October 20, 2014 |...

209

The Heating of Corn Chops.  

E-Print Network [OSTI]

OF SUB-STATIONS. E. E. B in fobd , Beeville Sub-Station......... ................................... Beeville, Bee County W, S. H o tc h k is s , Troup Sub-Station........................................ Troup, Smith County E. M. J oh n s to n... , Cooperative Rice Station................Beaumont, Jefferson County I. S. Y o rk , Spur Sub-Station.......................................................... Spur, Dickens County T. W . B u e l l , Denton, Sub...

Fraps, G. S.

1912-01-01T23:59:59.000Z

210

Kansas City`s Union Station redevelopment opportunity -- Environmental challenges  

SciTech Connect (OSTI)

Kansas City`s Union Station, located at the center of a 1.7 million metropolitan population, is the second largest train station in the United States. The Station ceased to operate as a train station in 1983 and has since been falling into an increasing state of disrepair. This paper provides an insight into ``brownfield`` redevelopment and renovation for adaptive reuse of major turn of the century facilities such as Union Station. Substantial assessment and investigation activities have been conducted at Union Station for compliance and corrective action under RCRA, TSCA, and associated state regulations encompassing remediation estimated at more than $3 million. Recognized environmental conditions identified at Union Station included potential underground storage tanks; solid wastes, special wastes, and potentially hazardous wastes located inside the building; free liquids in sumps and elevator pits; asbestos-containing materials; lead-based paint; and potential for soil contamination on the surrounding property.

Snyder, M.G. [Black and Veatch Waste Science, Inc., Overland Park, KS (United States); Scott, A. [Union Station Assistance Corp., Kansas City, MO (United States)

1995-12-31T23:59:59.000Z

211

Heat transport in the North Atlantic Ocean  

E-Print Network [OSTI]

L IB R AR Y A&M COLLEGE OF TEXAS HEAT TRANSPORT IN THE NORTH ATLANTIS OCEAN A Dissertation By GLENN HAROLD JUNG Submitted to the Graduate School of the Agricultural and Mechanical College of Texas in partial fulfillment of the requirements... the velocity difference be? tween depths 1 and 2 in a region between stations situated at positions A and B is used: V1 - v2 z l r - (DA - db ) (2) where c is 1/2X1 sin)#,-ft- Is the angular velocity of the earth, 0 is the latitude of the region, L...

Jung, Glenn Harold

2013-10-04T23:59:59.000Z

212

Rotary magnetic heat pump  

DOE Patents [OSTI]

A rotary magnetic heat pump constructed without flow seals or segmented rotor accomplishes recuperation and regeneration by using split flow paths. Heat exchange fluid pumped through heat exchangers and returned to the heat pump splits into two flow components: one flowing counter to the rotor rotation and one flowing with the rotation. 5 figs.

Kirol, L.D.

1987-02-11T23:59:59.000Z

213

Mass and Heat Recovery  

E-Print Network [OSTI]

In the last few years heat recovery was under spot and in air conditioning fields usually we use heat recovery by different types of heat exchangers. The heat exchanging between the exhaust air from the building with the fresh air to the building...

Hindawai, S. M.

2010-01-01T23:59:59.000Z

214

Direct fired heat exchanger  

SciTech Connect (OSTI)

A gas-to-liquid heat exchanger system which transfers heat from a gas, generally the combustion gas of a direct-fired generator of an absorption machine, to a liquid, generally an absorbent solution. The heat exchanger system is in a counterflow fluid arrangement which creates a more efficient heat transfer.

Reimann, Robert C. (Lafayette, NY); Root, Richard A. (Spokane, WA)

1986-01-01T23:59:59.000Z

215

Rotary magnetic heat pump  

DOE Patents [OSTI]

A rotary magnetic heat pump constructed without flow seals or segmented rotor accomplishes recuperation and regeneration by using split flow paths. Heat exchange fluid pumped through heat exchangers and returned to the heat pump splits into two flow components: one flowing counter to the rotor rotation and one flowing with the rotation.

Kirol, Lance D. (Shelly, ID)

1988-01-01T23:59:59.000Z

216

Unusual Structure and Magnetism in MnO Nanoclusters  

E-Print Network [OSTI]

We report an unusual evolution of structure and magnetism in stoichiometric MnO clusters based on an extensive and unbiased search through the potential energy surface within density functional theory. The smaller clusters, containing up to five MnO units, adopt two-dimensional structures; and regardless of the size of the cluster, magnetic coupling is found to be antiferromagnetic in contrast to previous theoretical findings. Predicted structure and magnetism are strikingly different from the magnetic core of Mn-based molecular magnets, whereas they were previously argued to be similar. Both of these features are explained through the inherent electronic structures of the clusters.

Ganguly, Shreemoyee; Sanyal, Biplab; Mookerjee, Abhijit; 10.1103/PhysRevB.83.020411

2011-01-01T23:59:59.000Z

217

Parallel Polarization EPR Characterization of the Mn(III) Center of Oxidized Manganese Superoxide  

E-Print Network [OSTI]

Parallel Polarization EPR Characterization of the Mn(III) Center of Oxidized Manganese Superoxide polarization CW-EPR to investigate the paramagnetic Mn3+ ion of the MnSOD enzyme from Escherichia coli with a positive axial zero-field splitting value, D, are arranged as shown in Figure 1. An EPR signal from the Mn

Miller, Anne-Frances

218

Thulium-170 heat source  

DOE Patents [OSTI]

An isotopic heat source is formed using stacks of thin individual layers of a refractory isotopic fuel, preferably thulium oxide, alternating with layers of a low atomic weight diluent, preferably graphite. The graphite serves several functions: to act as a moderator during neutron irradiation, to minimize bremsstrahlung radiation, and to facilitate heat transfer. The fuel stacks are inserted into a heat block, which is encased in a sealed, insulated and shielded structural container. Heat pipes are inserted in the heat block and contain a working fluid. The heat pipe working fluid transfers heat from the heat block to a heat exchanger for power conversion. Single phase gas pressure controls the flow of the working fluid for maximum heat exchange and to provide passive cooling.

Walter, Carl E. (Pleasanton, CA); Van Konynenburg, Richard (Livermore, CA); VanSant, James H. (Tracy, CA)

1992-01-01T23:59:59.000Z

219

Heat Treating Apparatus  

DOE Patents [OSTI]

Apparatus for heat treating a heat treatable material including a housing having an upper opening for receiving a heat treatable material at a first temperature, a lower opening, and a chamber therebetween for heating the heat treatable material to a second temperature higher than the first temperature as the heat treatable material moves through the chamber from the upper to the lower opening. A gas supply assembly is operatively engaged to the housing at the lower opening, and includes a source of gas, a gas delivery assembly for delivering the gas through a plurality of pathways into the housing in countercurrent flow to movement of the heat treatable material, whereby the heat treatable material passes through the lower opening at the second temperature, and a control assembly for controlling conditions within the chamber to enable the heat treatable material to reach the second temperature and pass through the lower opening at the second temperature as a heated material.

De Saro, Robert (Annandale, NJ); Bateman, Willis (Sutton Colfield, GB)

2002-09-10T23:59:59.000Z

220

Existing climate data sources and Their Use in Heat IslandResearch  

SciTech Connect (OSTI)

Existing climate data sources can be used in two general types of analysis for the detection of urban heat islands. Historical analyses use long-term data records-preferentially from several locations in and around an urban area-to trace the gradual influence of urban development on its climate. Primary sources of such data include the cooperative network, first-order National Weather Service stations, and military weather stations. Analyses of short-term data use information from a dense urban weather station network to discern the location, extent, and magnitude of urban heat islands. Such analyses may use the aforementioned national networks or regional networks such as agricultural, air quality monitoring, or utility networks. We demonstrate the use of existing data sources with a historical analysis of temperature trends in Los Angeles, California, and an analysis of short-term data of the urban temperature profile for Phoenix, Arizona. The Los Angeles climate was examined with eleven long-term data records from the cooperative network. Statistically significant trends of rising temperature were detected at Los Angeles Civic Center and other stations over some parts of the year, although timing of the increase varied from station to station. Observed increases in temperatures maybe due to long-term climate changes, microclimate influences, or local-scale heat islands. The analysis of short-term data was made for Phoenix using the PRISMS station network. Mean diurnal temperature profiles for a month were examined and compared with those for adjacent rural areas. Data fi-om stations in the center of Phoenix showed clear and significant nighttime and daytime temperature differences of 1- 2K (3 - 4"F). These temperature increases maybe attributable to a local-scale heat island.

Akbari, Hashem; Pon, Brian; Smith, Craig Kenton; Stamper-Kurn, Dan Moses

1998-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Sandia National Laboratories: Reference Station Design  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassive SolarEducationStationCSPRecovery Act Solar Test Facility Upgrades

222

Thermoelectric heat exchange element  

DOE Patents [OSTI]

A thermoelectric heat exchange module includes a first substrate including a heat receptive side and a heat donative side and a series of undulatory pleats. The module may also include a thermoelectric material layer having a ZT value of 1.0 or more disposed on at least one of the heat receptive side and the heat donative side, and an electrical contact may be in electrical communication with the thermoelectric material layer.

Callas, James J. (Peoria, IL); Taher, Mahmoud A. (Peoria, IL)

2007-08-14T23:59:59.000Z

223

Report on Experiments with Citrus Fruits at the Beeville Sub-station.  

E-Print Network [OSTI]

!TEXAS AGRICULTURAL EXPERIMENT STATIONS BULLETIN No. 148. MAY, 1912. Report on Experiments With Citrus Fruits at The Bee- ville Sub-station A. T. POTTS, Superintendent Beeville Sub-station AUSTIN PRINTING COMPANY AUSTIN. TEXAS TEXAS... EXPERIMENT STATIONS. GOVERNING BOARD. 1 DIRECTOR OF STATIONS. ...................................... B. YOUNOBLOOD, M. S.. .College Station I SUPERINTENDENTS OF SUB-STATIONS. .................. E. E. BINFORD, Beeville Sub-station.. .Beeville, P:.e Cc...

Potts, A. T. (Arthur Tillman)

1912-01-01T23:59:59.000Z

224

Heat Integrate Heat Engines in Process Plants  

E-Print Network [OSTI]

of forcing a good fit between a heat engine and process T', H profiles extends the ideas of appropriate and inappropriate placement to give bet ter overall integration schemes [7] . The new 'and powerful representations of the thermodynamics of a process... HEAT INTEGRATE HEAT ENGINES IN PROCESS PLANTS E. Hindmarsh, D. Boland and D.W. Townsend TENSA Technology, Houston, Texas Shorter Version Appeared in Chemical Engineering Copyright McGraw Hill, 1985 ABSTRACT This paper presents a novel method...

Hindmarsh, E.; Boland, D.; Townsend, D. W.

225

Effects of strain amplitude and temperature on the damping capacity of an Fe-19Mn alloy with different microstructures  

SciTech Connect (OSTI)

The influences of strain amplitude (10{sup -5}-10{sup -4}) and temperature (25 deg. C-500 deg. C) on the internal friction of a cold-drawn and solution treated Fe-19Mn alloy were investigated. The internal friction was measured using reversal torsion pendulum and multifunction internal friction equipment. The microstructure was observed using scanning electron microscopy. The phase transformation temperatures were determined using differential scanning calorimetry. The results indicated that the internal friction of the solution treated alloy was related to strain amplitude, which could be explained using the movement of Shockley partial dislocations (bowing out and breaking away). But the internal friction of the cold-drawn alloy was independent of strain amplitude because of high density dislocations formed by cold forming. Moreover, when the temperature was changed between 25 deg. C and 500 deg. C, the internal friction of the cold-drawn alloy increased slowly from 25 deg. C to 375 deg. C, and then increased quickly from 375 deg. C to 500 deg. C. However, for the solution treated alloy, there was an internal friction peak at about 210 deg. C in the heating process (from 25 deg. C to 500 deg. C), and there was another internal friction peak at about 150 deg. C in the cooling process. These peaks could be explained using the heat-assisted movement of dislocations. - Research Highlights: {yields}Internal friction of solution treated Fe-19Mn alloy is related to strain amplitude. {yields}Internal friction of cold-drawn Fe-19Mn alloy is independent of strain amplitude. {yields}IF of cold-drawn alloy increases from RT to 500 deg. C. {yields}There is an IF peak of solution treated alloy in heating and cooling process separately. {yields}The results can be explained using the movement of dislocations.

Huang Shuke, E-mail: huangshuke@163.com [Institute of Machinery Manufacturing Technology, China Academy of Engineering Physics, Mianyang, Sichuan 621900 (China); Zhou Danchen; Liu Jianhui [Institute of Machinery Manufacturing Technology, China Academy of Engineering Physics, Mianyang, Sichuan 621900 (China); Teng Jin; Li Ning; Wen Yuhua [School of Manufacturing Science and Engineering, Sichuan University, Chengdu, Sichuan 610065 (China)

2010-11-15T23:59:59.000Z

226

Transverse acoustic actuation of Ni-Mn-Ga single crystals  

E-Print Network [OSTI]

Two methods for the transverse acoustic actuation of {110}-cut Ni-Mn-Ga single crystals are discussed. In this actuation mode, crystals are used that have the {110}- type twinning planes parallel to the base of the crystal. ...

Simon, Jesse Matthew

2007-01-01T23:59:59.000Z

227

The University of Wisconsin-Milwaukee Field Station The Field Station is celebrating its 50th  

E-Print Network [OSTI]

land, until today the Field Station has grown into an active, vibrant facility with many projects for experimental research. Growth of our facilities has been funded by the National Science Foundation Bat Hibernaculum, an abandoned iron mine in Dodge County that is one of the largest sites

Saldin, Dilano

228

Energy Balance Bowen Ratio Station (EBBR) Handbook  

SciTech Connect (OSTI)

The energy balance Bowen ratio (EBBR) system produces 30-minute estimates of the vertical fluxes of sensible and latent heat at the local surface. Flux estimates are calculated from observations of net radiation, soil surface heat flux, and the vertical gradients of temperature and relative humidity (RH). Meteorological data collected by the EBBR are used to calculate bulk aerodynamic fluxes, which are used in the Bulk Aerodynamic Technique (BA) EBBR value-added product (VAP) to replace sunrise and sunset spikes in the flux data. A unique aspect of the system is the automatic exchange mechanism (AEM), which helps to reduce errors from instrument offset drift.

Cook, DR

2011-02-23T23:59:59.000Z

229

Ambi-site substitution of Mn in lanthanum germanate apatites  

SciTech Connect (OSTI)

A neutron diffraction study at 4 K of the Mn doped lanthanum germanate apatite-type oxide ion conductor of nominal starting composition 'La{sub 9.5}Mn{sub 0.5}(GeO{sub 4}){sub 6}O{sub 2.75}' is reported. The structure was refined in space group P6{sub 3}/m, although high thermal displacement parameters were observed for the oxide ion sites (particularly O3, and O4). Reduced thermal displacement parameters were obtained by splitting the O3 site, and allowing the O4 oxygen to move off site, which may indicate local regions of lower symmetry within the structure. In addition, the data suggested ambi-site substitution of Mn, with it being present on both the Ge site and the La site. Assuming no change in La:Mn:Ge ratio, a composition of La{sub 9.18}Mn{sub 0.28}(GeO{sub 4}){sub 5.8}(MnO{sub 4}){sub 0.2}O{sub 2} was determined. As such there are nominally no interstitial oxide ions, but rather cation vacancies on the La site. Therefore, the high conductivity for this sample is most likely related to the introduction of Frenkel-type defects at higher temperature, as previously proposed for other apatite-type systems containing vacancies on the La site.

Kendrick, E. [Chemical Sciences, University of Surrey, Guildford, Surrey GU2 7XH (United Kingdom); Knight, K.S. [ISIS Facility, Rutherford Appleton Laboratory, Harwell Science and Innovation Campus, Didcot OX11 0QX (United Kingdom); Slater, P.R., E-mail: p.r.slater@bham.ac.uk [School of Chemistry, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom)

2009-08-05T23:59:59.000Z

230

Magnetoluminescence of CdTe/MnTe/CdMgTe heterostructures with ultrathin MnTe layers  

SciTech Connect (OSTI)

CdTe/MnTe/CdMgTe quantum-well structures with one or two monolayers of MnTe inserted at CdTe/CdMgTe interfaces were fabricated. The spectra of the excitonic luminescence from CdTe quantum wells and their variation with temperature indicate that introduction of ultrathin MnTe layers improves the interface quality. The effect of a magnetic field in the Faraday configuration on the spectral position of the exciton-emission peaks indicates that frustration of magnetic moments in one-monolayer MnTe insertions is weaker than in two-monolayer insertions. The effect of a magnetic field on the exciton localization can be explained in terms of the exciton wave-function shrinkage and obstruction of the photoexcited charge-carrier motion in the quantum well.

Agekyan, V. F., E-mail: vfag@rambler.ru [St. Petersburg State University, Fock Institute of Physics (Russian Federation); Holz, P. O. [Polish Academy of Sciences, Institute of Physics (Poland); Karczewski, G. [Linkoeping University (Sweden); Katz, V. N. [St. Petersburg State University, Fock Institute of Physics (Russian Federation); Moskalenko, E. S. [Russian Academy of Sciences, Ioffe Physical Technical Institute (Russian Federation); Serov, A. Yu.; Filosofov, N. G. [St. Petersburg State University, Fock Institute of Physics (Russian Federation)

2011-10-15T23:59:59.000Z

231

Heat transfer system  

DOE Patents [OSTI]

A heat transfer system for a nuclear reactor. Heat transfer is accomplished within a sealed vapor chamber which is substantially evacuated prior to use. A heat transfer medium, which is liquid at the design operating temperatures, transfers heat from tubes interposed in the reactor primary loop to spaced tubes connected to a steam line for power generation purposes. Heat transfer is accomplished by a two-phase liquid-vapor-liquid process as used in heat pipes. Condensible gases are removed from the vapor chamber through a vertical extension in open communication with the chamber interior.

McGuire, Joseph C. (Richland, WA)

1982-01-01T23:59:59.000Z

232

Heat transfer system  

DOE Patents [OSTI]

A heat transfer system for a nuclear reactor is described. Heat transfer is accomplished within a sealed vapor chamber which is substantially evacuated prior to use. A heat transfer medium, which is liquid at the design operating temperatures, transfers heat from tubes interposed in the reactor primary loop to spaced tubes connected to a steam line for power generation purposes. Heat transfer is accomplished by a two-phase liquid-vapor-liquid process as used in heat pipes. Condensible gases are removed from the vapor chamber through a vertical extension in open communication with the chamber interior.

Not Available

1980-03-07T23:59:59.000Z

233

Resilient design of recharging station networks for electric transportation vehicles  

SciTech Connect (OSTI)

As societies shift to 'greener' means of transportation using electricity-driven vehicles one critical challenge we face is the creation of a robust and resilient infrastructure of recharging stations. A particular issue here is the optimal location of service stations. In this work, we consider the placement of battery replacing service station in a city network for which the normal traffic flow is known. For such known traffic flow, the service stations are placed such that the expected performance is maximized without changing the traffic flow. This is done for different scenarios in which roads, road junctions and service stations can fail with a given probability. To account for such failure probabilities, the previously developed facility interception model is extended. Results show that service station failures have a minimal impact on the performance following robust placement while road and road junction failures have larger impacts which are not mitigated easily by robust placement.

Kris Villez; Akshya Gupta; Venkat Venkatasubramanian

2011-08-01T23:59:59.000Z

234

Diversity of Mn oxides produced by Mn(II)-oxidizing fungi. | EMSL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed Newcatalyst phasesDataTranslocationDiurnal Cycle of Convection atDiversity of Mn

235

State Heating Oil and Propane Program, 1990--1991 heating season. Final technical report  

SciTech Connect (OSTI)

The following discussion summarizes the survey approach and results of the Department of Public Service`s survey of retail fuel oil and propane prices during the 1990--91 heating season. The semi-monthly phone surveys were conducted in cooperation with the US Department of Energy`s State Fuel Oil and Propane Program, which coordinated surveys of heating fuel prices by 25 eastern and midwest states. This federal/state program serves as a method for fast collection, analysis, and dissemination of information on current residential prices. No other information source meets needs for timely retail price information over the course of the heating season. For the 1990--91 heating season, the Minnesota Department of Public Service (MN/DPS) expanded the scope of its survey effort to include regional price data. Surveys were conducted with 160 retailers, including 59 respondents from the DOE samples, to provide a reasonable sample size for each region. Fuel oil retailers were also asked for updates on their secondary inventory levels.

Not Available

1991-06-06T23:59:59.000Z

236

State Heating Oil and Propane Program, 1990--1991 heating season  

SciTech Connect (OSTI)

The following discussion summarizes the survey approach and results of the Department of Public Service's survey of retail fuel oil and propane prices during the 1990--91 heating season. The semi-monthly phone surveys were conducted in cooperation with the US Department of Energy's State Fuel Oil and Propane Program, which coordinated surveys of heating fuel prices by 25 eastern and midwest states. This federal/state program serves as a method for fast collection, analysis, and dissemination of information on current residential prices. No other information source meets needs for timely retail price information over the course of the heating season. For the 1990--91 heating season, the Minnesota Department of Public Service (MN/DPS) expanded the scope of its survey effort to include regional price data. Surveys were conducted with 160 retailers, including 59 respondents from the DOE samples, to provide a reasonable sample size for each region. Fuel oil retailers were also asked for updates on their secondary inventory levels.

Not Available

1991-06-06T23:59:59.000Z

237

Application of Mn/DOT Utility Coordination Process to Local Agencies Based on national best practices, the Minnesota Department of Transportation (Mn/DOT) Utility  

E-Print Network [OSTI]

Application of Mn/DOT Utility Coordination Process to Local Agencies Based on national best practices, the Minnesota Department of Transportation (Mn/DOT) Utility Coordination Process incorporates Processes There are projects where the full process is not necessary. The Mn/DOT Utilities Manual provides

Minnesota, University of

238

Comparison of the EXAFS Spectra of Heteronuclear MnCa/Sr Model Complexes to the Oxygen-Evolving Mn(4)Ca Complex of Photosystem II  

SciTech Connect (OSTI)

Heterometallic Mn-Ca and Mn-Sr complexes have been prepared and employed as model complexes for Ca and Sr EXAFS spectral comparisons with the Oxygen-Evolving Complex (OEC) of Photosystem II (PS II); these have revealed similarities that support the presence of at least one O atom bridge between the Mn and Ca/Sr in the OEC.

Mishra, A.; Yano, J.; Pushkar, Y.; Abboud, K.A.; Yachandra, V.K.; Christou, G.

2009-06-03T23:59:59.000Z

239

New Jersey Nuclear Profile - PSEG Salem Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

PSEG Salem Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

240

California Nuclear Profile - San Onofre Nuclear Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

San Onofre Nuclear Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

New Jersey Nuclear Profile - PSEG Hope Creek Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

PSEG Hope Creek Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

242

Illinois Nuclear Profile - LaSalle Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

LaSalle Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration...

243

New York Nuclear Profile - Nine Mile Point Nuclear Station  

U.S. Energy Information Administration (EIA) Indexed Site

Nine Mile Point Nuclear Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

244

Electric Vehicle Charging Stations, Coming Soon to a City Near...  

Broader source: Energy.gov (indexed) [DOE]

to be available throughout the Orlando area next year. File photo Orlando Plugs into Electric Vehicle Charging Stations Assistant Secretary Patricia Hoffman test drives the...

245

Investigations of Sediment Elutriate Toxicity at Three Estuarine Stations  

E-Print Network [OSTI]

Investigations of Sediment Elutriate Toxicity at Three Estuarine Stations in San Francisco Bay.............................................................................................. 8 Sediment-Water Interface Exposures................................................................................. 9 August 1997 Sediment-Water Interface Exposures

246

Microgrid V2G Charging Station Interconnection Testing (Presentation)  

SciTech Connect (OSTI)

This presentation by Mike Simpson of the National Renewable Energy Laboratory (NREL) describes NREL's microgrid vehicle-to-grid charging station interconnection testing.

Simpson, M.

2013-07-01T23:59:59.000Z

247

anna power station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

1 Regarding Kewaunee Power Station CiteSeer Summary: This supplemental environmental impact statement (SEIS) has been prepared in response to an application submitted by Dominion...

248

anna power stations: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

1 Regarding Kewaunee Power Station CiteSeer Summary: This supplemental environmental impact statement (SEIS) has been prepared in response to an application submitted by Dominion...

249

Sandia National Laboratories: More California Gas Stations Can...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

than Previously Thought, Sandia Study Says More California Gas Stations Can Provide Hydrogen than Previously Thought, Sandia Study Says Diamond Plates Create Nanostructures...

250

The Fuel-Travel-Back Approach to Hydrogen Station Siting  

E-Print Network [OSTI]

costs of cars with alternative fuels/engines." Energy Policyto the Choice of Alternative Fuels and Vehicles." Energyhydrogen; station location; alternative fuel; optimization

Lin, Zhenhong; Ogden, Joan; Fan, Yueyue; Chen, Chien-Wei

2009-01-01T23:59:59.000Z

251

Columbia Generating Station debt options for rate relief - November...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

extending about 350 million of existing Columbia Generating Station debt to 2024 to the Energy Northwest Audit, Legal and Finance Committee (www.bpa.govcorporateFinanceDebt...

252

Design of Photovoltaics e-bikes charging station:.  

E-Print Network [OSTI]

??It is a project about designing a photovoltaics charging station for electrical bikes and scooters, which can facilitate electrical bike user and promote sustainable way… (more)

Zhao, Y.

2014-01-01T23:59:59.000Z

253

Consolidated Electric Cooperative- Heat Pump and Water Heating Rebates  

Broader source: Energy.gov [DOE]

Consolidated Electric Cooperative provides rebates to residential customers who install electric water heaters, dual-fuel heating system or geothermal heat pumps. A dual-fuel heating systems...

254

Solar Powered Radioactive Air Monitoring Stations  

SciTech Connect (OSTI)

Environmental monitoring of ambient air for radioactive material is required as stipulated in the PNNL Site radioactive air license. Sampling ambient air at identified preferred locations could not be initially accomplished because utilities were not readily available. Therefore, solar powered environmental monitoring systems were considered as a possible option. PNNL purchased two 24-V DC solar powered environmental monitoring systems which consisted of solar panels, battery banks, and sampling units. During an approximate four month performance evaluation period, the solar stations operated satisfactorily at an on-site test location. They were subsequently relocated to their preferred locations in June 2012 where they continue to function adequately under the conditions found in Richland, Washington.

Barnett, J. M.; Bisping, Lynn E.; Gervais, Todd L.

2013-10-30T23:59:59.000Z

255

Photovoltaic roof heat flux  

E-Print Network [OSTI]

designs (relatively) Photovoltaic Solar P a n e l AtmosphereCALIFORNIA, SAN DIEGO Photovoltaic Roof Heat Flux A ThesisABSTRACT OF T H E THESIS Photovoltaic Roof Heat Flux by

Samady, Mezhgan Frishta

2011-01-01T23:59:59.000Z

256

HEAT TRANSFER FLUIDS  

E-Print Network [OSTI]

The choice of heat transfer fluids has significant effects on the performance, cost, and reliability of solar thermal systems. In this chapter, we evaluate existing heat transfer fluids such as oils and molten salts based ...

Lenert, Andrej

2012-01-01T23:59:59.000Z

257

Heat treatment effects on microstructure and magnetic properties of MnZn ferrite powders  

E-Print Network [OSTI]

synthesizing methods have been reported recently, including co-precipitation, alcohol dehydration, hydrothermal and good reactivity [14,15]. The advantages of this method are processing simplicity, low energy loss, high

Volinsky, Alex A.

258

Effect of Composition and Heat Treatment on MnBi Magnetic Materials. | EMSL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed NewcatalystNeutronEnvironmentZIRKLE FRUITYear 1MATERIALSTiO2(110). | EMSLCoal

259

Abrasion resistant heat pipe  

DOE Patents [OSTI]

A specially constructed heat pipe for use in fluidized bed combustors. Two distinct coatings are spray coated onto a heat pipe casing constructed of low thermal expansion metal, each coating serving a different purpose. The first coating forms aluminum oxide to prevent hydrogen permeation into the heat pipe casing, and the second coating contains stabilized zirconium oxide to provide abrasion resistance while not substantially affecting the heat transfer characteristics of the system.

Ernst, Donald M. (Leola, PA)

1984-10-23T23:59:59.000Z

260

MA HEAT Loan Overview  

Broader source: Energy.gov [DOE]

Presents information on the success of Massachusetts's HEAT loan offerings and how the financing tool is funded.

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Abrasion resistant heat pipe  

DOE Patents [OSTI]

A specially constructed heat pipe is described for use in fluidized bed combustors. Two distinct coatings are spray coated onto a heat pipe casing constructed of low thermal expansion metal, each coating serving a different purpose. The first coating forms aluminum oxide to prevent hydrogen permeation into the heat pipe casing, and the second coating contains stabilized zirconium oxide to provide abrasion resistance while not substantially affecting the heat transfer characteristics of the system.

Ernst, D.M.

1984-10-23T23:59:59.000Z

262

Solar heat receiver  

DOE Patents [OSTI]

A receiver is described for converting solar energy to heat a gas to temperatures from 700 to 900/sup 0/C. The receiver is formed to minimize impingement of radiation on the walls and to provide maximum heating at and near the entry of the gas exit. Also, the receiver is formed to provide controlled movement of the gas to be heated to minimize wall temperatures. The receiver is designed for use with gas containing fine heat absorbing particles, such as carbon particles.

Hunt, A.J.; Hansen, L.J.; Evans, D.B.

1982-09-29T23:59:59.000Z

263

Project X Energy Station Workshop Report. Report by the Organizers and Co-Conveners of the Project X Energy Station Workshop  

SciTech Connect (OSTI)

Project X Energy Station Workshop Report Report by the Organizers and Co-Conveners of the Project X Energy Station Workshop

Asner, David M.; Hurh, Patrick; Brady Raap, Michaele C.; Gohar, Yoursy; Peterson, Mary E.; Pithcer, Eric; Riemer, Bernie; Senor, David J.; Wootan, David W.

2013-06-14T23:59:59.000Z

264

Ammoniated salt heat pump  

SciTech Connect (OSTI)

A thermochemical heat pump/energy storage system using liquid ammoniate salts is described. The system, which can be used for space heating or cooling, provides energy storage for both functions. The bulk of the energy is stored as chemical energy and thus can be stored indefinitely. The system is well suited to use with a solar energy source or industrial waste heat.

Haas, W.R.; Jaeger, F.J.; Giordano, T.J.

1981-01-01T23:59:59.000Z

265

Heat Transfer Guest Editorial  

E-Print Network [OSTI]

Journal of Heat Transfer Guest Editorial We are indeed delighted in bringing out this special issue was showcased in diverse areas such as traditional heat and mass transfer, lab-on-chip, sensors, biomedical applica- tions, micromixers, fuel cells, and microdevices. Selected papers in the field of heat transfer

Kandlikar, Satish

266

Acoustic Heating Peter Ulmschneider  

E-Print Network [OSTI]

mechanisms. 1. The acoustic heating theory Only a few years after Edlen's (1941) discovery that the solar acoustic wave radiation- · b. field acoustic wave Figure 1. Panel a: Acoustic heating in late-type stars: effective temperature TeJ f, gravity g and mixing length parameter fr. Panel b: Acoustic heating in early

Ulmschneider, Peter

267

Liquid heat capacity lasers  

DOE Patents [OSTI]

The heat capacity laser concept is extended to systems in which the heat capacity lasing media is a liquid. The laser active liquid is circulated from a reservoir (where the bulk of the media and hence waste heat resides) through a channel so configured for both optical pumping of the media for gain and for light amplification from the resulting gain.

Comaskey, Brian J. (Walnut Creek, CA); Scheibner, Karl F. (Tracy, CA); Ault, Earl R. (Livermore, CA)

2007-05-01T23:59:59.000Z

268

Pioneering Heat Pump Project  

Broader source: Energy.gov [DOE]

Project objectives: To install and monitor an innovative WaterFurnace geothermal system that is technologically advanced and evolving; To generate hot water heating from a heat pump that uses non-ozone depleting refrigerant CO2. To demonstrate the energy efficiency of this system ground source heat pump system.

269

Final environmental assessment for vegetation control at VHF stations, microwave stations, electrical substations, and pole yards  

SciTech Connect (OSTI)

Southwestern Power Adm. operates very high frequency (VHF) and microwave radio stations, electrical substations, and pole yards for electric power transmission throughout AR, MO, and OK. Vegetation growth at the stations must be suppressed for safety of operation and personnel. Southwestern has been using a combination of mechanical/manual and herbicide control for this purpose; Federally- mandated reductions in staff and budgetary resources require Southwestern to evaluate all potentially efficient methods for vegetation control. Three alternatives were examined: no action, mechanical/manual control, and (proposed) a combination of mechanical/manual and herbicide control. Environmental impacts on air and water quality, wetlands, wildlife, endangered species, archaeological and other resources, farmland, human health, transportation, etc. were evaluated.

NONE

1995-10-13T23:59:59.000Z

270

A corrosive resistant heat exchanger  

DOE Patents [OSTI]

A corrosive and erosive resistant heat exchanger which recovers heat from a contaminated heat stream. The heat exchanger utilizes a boundary layer of innocuous gas, which is continuously replenished, to protect the heat exchanger surface from the hot contaminated gas. The innocuous gas is pumped through ducts or perforations in the heat exchanger wall. Heat from the heat stream is transferred by radiation to the heat exchanger wall. Heat is removed from the outer heat exchanger wall by a heat recovery medium. 3 figs., 3 tabs.

Richlen, S.L.

1987-08-10T23:59:59.000Z

271

GC GUIDANCE ON ELECTRIC VEHICLE RECHARGING STATIONS  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Subject: Guidance for natural gas as a feedstock for

272

Hydrogen Fueling Infrastructure Research and Station Technology  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Subject:Groundto ApplyRoadmap HydrogenHydrogen Fuel

273

Chemical heat pump  

DOE Patents [OSTI]

A chemical heat pump system is disclosed for use in heating and cooling structures such as residences or commercial buildings. The system is particularly adapted to utilizing solar energy, but also increases the efficiency of other forms of thermal energy when solar energy is not available. When solar energy is not available for relatively short periods of time, the heat storage capacity of the chemical heat pump is utilized to heat the structure as during nighttime hours. The design also permits home heating from solar energy when the sun is shining. The entire system may be conveniently rooftop located. In order to facilitate installation on existing structures, the absorber and vaporizer portions of the system may each be designed as flat, thin wall, thin pan vessels which materially increase the surface area available for heat transfer. In addition, this thin, flat configuration of the absorber and its thin walled (and therefore relatively flexible) construction permits substantial expansion and contraction of the absorber material during vaporization and absorption without generating voids which would interfere with heat transfer. The heat pump part of the system heats or cools a house or other structure through a combination of evaporation and absorption or, conversely, condensation and desorption, in a pair of containers. A set of automatic controls change the system for operation during winter and summer months and for daytime and nighttime operation to satisfactorily heat and cool a house during an entire year. The absorber chamber is subjected to solar heating during regeneration cycles and is covered by one or more layers of glass or other transparent material. Daytime home air used for heating the home is passed at appropriate flow rates between the absorber container and the first transparent cover layer in heat transfer relationship in a manner that greatly reduce eddies and resultant heat loss from the absorbant surface to ambient atmosphere.

Greiner, Leonard (2750-C Segerstrom Ave., Santa Ana, CA 92704)

1980-01-01T23:59:59.000Z

274

Hydrothermal synthesis and catalytic properties of {alpha}- and {beta}-MnO{sub 2} nanorods  

SciTech Connect (OSTI)

One-dimensional {alpha}-MnO{sub 2} and {beta}-MnO{sub 2} single-crystalline nanostructures were prepared by hydrothermal process. The products were characterized in detail by multiform techniques: X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Experimental results indicate that the temperature plays important roles in determining produce {alpha}-MnO{sub 2} and {beta}-MnO{sub 2} nanorods. In addition, the as-prepared {alpha}-MnO{sub 2} and {beta}-MnO{sub 2} nanorods showed excellent catalytic performance in the Fenton-like reaction.

Cao, Guangsheng, E-mail: daqingcgs@163.com [Key Laboratory of Enhanced Oil and Gas Recovery of Ministry of Education, Daqing Petroleum Institute, Daqing 163318 (China)] [Key Laboratory of Enhanced Oil and Gas Recovery of Ministry of Education, Daqing Petroleum Institute, Daqing 163318 (China); Su, Ling; Zhang, Xiaojuan; Li, Hui [Key Laboratory of Enhanced Oil and Gas Recovery of Ministry of Education, Daqing Petroleum Institute, Daqing 163318 (China)] [Key Laboratory of Enhanced Oil and Gas Recovery of Ministry of Education, Daqing Petroleum Institute, Daqing 163318 (China)

2010-04-15T23:59:59.000Z

275

Absorption heat pump system  

DOE Patents [OSTI]

An improvement in an absorption heat pump cycle is obtained by adding adiabatic absorption and desorption steps to the absorber and desorber of the system. The adiabatic processes make it possible to obtain the highest temperature in the absorber before any heat is removed from it and the lowest temperature in the desorber before heat is added to it, allowing for efficient utilization of the thermodynamic availability of the heat supply stream. The improved system can operate with a larger difference between high and low working fluid concentrations, less circulation losses, and more efficient heat exchange than a conventional system.

Grossman, Gershon (Oak Ridge, TN); Perez-Blanco, Horacio (Knoxville, TN)

1984-01-01T23:59:59.000Z

276

Spin dependent transport properties of Mn-Ga/MgO/Mn-Ga magnetic tunnel junctions with metal(Mg, Co, Cr) insertion layer  

SciTech Connect (OSTI)

We report a first principles theoretical investigation of spin polarized quantum transport in Mn{sub 2}Ga/MgO/Mn{sub 2}Ga and Mn{sub 3}Ga/MgO/Mn{sub 3}Ga magnetic tunneling junctions (MTJs) with the consideration of metal(Mg, Co, Cr) insertion layer effect. By changing the concentration of Mn, our calculation shows a considerable disparity in transport properties: A tunneling magnetoresistance (TMR) ratio of 852% was obtained for Mn{sub 2}Ga-based MTJs, however, only a 5% TMR ratio for Mn{sub 3}Ga-based MTJs. In addition, the influence of insertion layer has been considered in our calculation. We found the Co insertion layer can increase the TMR of Mn{sub 2}Ga-based MTJ to 904%; however, the Cr insertion layer can decrease the TMR by 668%; A negative TMR ratio can be obtained with Mg insertion layer. Our work gives a comprehensive understanding of the influence of different insertion layer in Mn-Ga based MTJs. It is proved that, due to the transmission can be modulated by the interfacial electronic structure of insertion, the magnetoresistance ratio of Mn{sub 2}Ga/MgO/Mn{sub 2}Ga MTJ can be improved by inserting Co layer.

Liang, S. H.; Tao, L. L.; Liu, D. P., E-mail: dpliu@iphy.ac.cn; Han, X. F., E-mail: xfhan@iphy.ac.cn [State Key Laboratory of Magnetism, Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Lu, Y. [Institut Jean Lamour, UMR 7198, CNRS-Nancy Université, BP 239, 54506 Vandoeuvre (France)

2014-04-07T23:59:59.000Z

277

A comparative study of magnetic behaviors in TbNi{sub 2}, TbMn{sub 2} and TbNi{sub 2}Mn  

SciTech Connect (OSTI)

All TbNi{sub 2}, TbMn{sub 2}, and TbNi{sub 2}Mn compounds exhibit the cubic Laves phase with AB{sub 2}-type structure in spite of the fact that the ratio of the Tb to transition-metal components in TbNi{sub 2}Mn is 1:3. Rietveld refinement indicates that in TbNi{sub 2}Mn the Mn atoms are distributed on both the A (8a) and B (16d) sites. The values of the lattice constants were measured to be a?=?14.348?Å (space group F-43?m), 7.618?Å, and 7.158?Å (space group Fd-3?m) for TbNi{sub 2}, TbMn{sub 2}, and TbNi{sub 2}Mn, respectively. The magnetic transition temperatures T{sub C} were found to be T{sub C}?=?38?K and T{sub C}?=?148?K for TbNi{sub 2} and TbNi{sub 2}Mn, respectively, while two magnetic phase transitions are detected for TbMn{sub 2} at T{sub 1}?=?20?K and T{sub 2}?=?49?K. Clear magnetic history effects in a low magnetic field are observed in TbMn{sub 2} and TbNi{sub 2}Mn. The magnetic entropy changes have been obtained.

Wang, J. L., E-mail: jianli@uow.edu.au [Institute for Superconductivity and Electronic Materials, University of Wollongong, Wollongong, NSW 2522 (Australia); Bragg Institute, ANSTO, Lucas Heights, NSW 2234 (Australia); Md Din, M. F.; Hong, F.; Cheng, Z. X.; Dou, S. X. [Institute for Superconductivity and Electronic Materials, University of Wollongong, Wollongong, NSW 2522 (Australia); Kennedy, S. J.; Studer, A. J. [Bragg Institute, ANSTO, Lucas Heights, NSW 2234 (Australia); Campbell, S. J. [School of Physical, Environmental and Mathematical Sciences, The University of New South Wales, Canberra, ACT 2600 (Australia); Wu, G. H. [Institute of Physics, Chinese Academy of Science, Beijing 100190 (China)

2014-05-07T23:59:59.000Z

278

ESBWR response to an extended station blackout/loss of all AC power  

SciTech Connect (OSTI)

U.S. federal regulations require light water cooled nuclear power plants to cope with Station Blackouts for a predetermined amount of time based on design factors for the plant. U.S. regulations define Station Blackout (SBO) as a loss of the offsite electric power system concurrent with turbine trip and unavailability of the onsite emergency AC power system. According to U.S. regulations, typically the coping period for an SBO is 4 hours and can be as long as 16 hours for currently operating BWR plants. Being able to cope with an SBO and loss of all AC power is required by international regulators as well. The U.S. licensing basis for the ESBWR is a coping period of 72 hours for an SBO based on U.S. NRC requirements for passive safety plants. In the event of an extended SBO (viz., greater than 72 hours), the ESBWR response shows that the design is able to cope with the event for at least 7 days without AC electrical power or operator action. ESBWR is a Generation III+ reactor design with an array of passive safety systems. The ESBWR primary success path for mitigation of an SBO event is the Isolation Condenser System (ICS). The ICS is a passive, closed loop, safety system that initiates automatically on a loss of power. Upon Station Blackout or loss of all AC power, the ICS begins removing decay heat from the Reactor Pressure Vessel (RPV) by (i) condensing the steam into water in heat exchangers located in pools of water above the containment, and (ii) transferring the decay heat to the atmosphere. The condensed water is then returned by gravity to cool the reactor again. The ICS alone is capable of maintaining the ESBWR in a safe shutdown condition after an SBO for an extended period. The fuel remains covered throughout the SBO event. The ICS is able to remove decay heat from the RPV for at least 7 days and maintains the reactor in a safe shutdown condition. The water level in the RPV remains well above the top of active fuel for the duration of the SBO event. Beyond 7 days, only a few simple actions are needed to cope with the SBO for an indefinite amount of time. The operation of the ICS as the primary success path for mitigation of an SBO, allows for near immediate plant restart once power is restored. (authors)

Barrett, A. J.; Marquino, W. [New Plants Engineering, GE Hitachi Nuclear Energy, M/CA 75, 3901 Castle Hayne Road, Wilmington, NC 28402 (United States)

2012-07-01T23:59:59.000Z

279

References Applicable to Station-Level Calibration Steve Ellingson  

E-Print Network [OSTI]

, W. Hocking, and F. Fabry, "Precipitation Measurement using VHF Wind-Profiler Radars: A MultifacetedReferences Applicable to Station-Level Calibration Steve Ellingson July 17, 2008 1 Summary This is a list of references possibly applicable to LWA station-level calibration. References [1] R.L. Balsano

Ellingson, Steven W.

280

Achieving High Chilled Water Delta T Without Blending Station  

E-Print Network [OSTI]

on the blending station performance. The results show that the blending station is not necessary in the building chilled water systems with 2-way modulation valves at end users. Actually the end user valve configuration and control mainly impacts building chilled...

Wang, Z.; Wang, G.; Xu, K.; Yu, Y.; Liu, M.

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Heat pump apparatus  

DOE Patents [OSTI]

A heat pump apparatus including a compact arrangement of individual tubular reactors containing hydride-dehydride beds in opposite end sections, each pair of beds in each reactor being operable by sequential and coordinated treatment with a plurality of heat transfer fluids in a plurality of processing stages, and first and second valves located adjacent the reactor end sections with rotatable members having multiple ports and associated portions for separating the hydride beds at each of the end sections into groups and for simultaneously directing a plurality of heat transfer fluids to the different groups. As heat is being generated by a group of beds, others are being regenerated so that heat is continuously available for space heating. As each of the processing stages is completed for a hydride bed or group of beds, each valve member is rotated causing the heat transfer fluid for the heat processing stage to be directed to that bed or group of beds. Each of the end sections are arranged to form a closed perimeter and the valve member may be rotated repeatedly about the perimeter to provide a continuous operation. Both valves are driven by a common motor to provide a coordinated treatment of beds in the same reactors. The heat pump apparatus is particularly suitable for the utilization of thermal energy supplied by solar collectors and concentrators but may be used with any source of heat, including a source of low-grade heat.

Nelson, Paul A. (Wheaton, IL); Horowitz, Jeffrey S. (Woodridge, IL)

1983-01-01T23:59:59.000Z

282

Active microchannel heat exchanger  

DOE Patents [OSTI]

The present invention is an active microchannel heat exchanger with an active heat source and with microchannel architecture. The microchannel heat exchanger has (a) an exothermic reaction chamber; (b) an exhaust chamber; and (c) a heat exchanger chamber in thermal contact with the exhaust chamber, wherein (d) heat from the exothermic reaction chamber is convected by an exothermic reaction exhaust through the exhaust chamber and by conduction through a containment wall to the working fluid in the heat exchanger chamber thereby raising a temperature of the working fluid. The invention is particularly useful as a liquid fuel vaporizer and/or a steam generator for fuel cell power systems, and as a heat source for sustaining endothermic chemical reactions and initiating exothermic reactions.

Tonkovich, Anna Lee Y. (Pasco, WA) [Pasco, WA; Roberts, Gary L. (West Richland, WA) [West Richland, WA; Call, Charles J. (Pasco, WA) [Pasco, WA; Wegeng, Robert S. (Richland, WA) [Richland, WA; Wang, Yong (Richland, WA) [Richland, WA

2001-01-01T23:59:59.000Z

283

Validation of an Integrated Hydrogen Energy Station  

SciTech Connect (OSTI)

This report presents the results of a 10-year project conducted by Air Products and Chemicals, Inc. (Air Products) to determine the feasibility of coproducing hydrogen with electricity. The primary objective was to demonstrate the technical and economic viability of a hydrogen energy station using a high-temperature fuel cell designed to produce power and hydrogen. This four-phase project had intermediate go/no-go decisions and the following specific goals: �¢���¢ Complete a technical assessment and economic analysis of the use of high-temperature fuel cells, including solid oxide and molten carbonate, for the co-production of power and hydrogen (energy park concept). �¢���¢ Build on the experience gained at the Las Vegas H2 Energy Station and compare/contrast the two approaches for co-production. �¢���¢ Determine the applicability of co-production from a high-temperature fuel cell for the existing merchant hydrogen market and for the emerging hydrogen economy. �¢���¢ Demonstrate the concept on natural gas for six months at a suitable site with demand for both hydrogen and electricity. �¢���¢ Maintain safety as the top priority in the system design and operation. �¢���¢ Obtain adequate operational data to provide the basis for future commercial activities, including hydrogen fueling stations. Work began with the execution of the cooperative agreement with DOE on 30 September 2001. During Phase 1, Air Products identified high-temperature fuel cells as having the potential to meet the coproduction targets, and the molten carbonate fuel cell system from FuelCell Energy, Inc. (FuelCell Energy) was selected by Air Products and DOE following the feasibility assessment performed during Phase 2. Detailed design, construction and shop validation testing of a system to produce 250 kW of electricity and 100 kilograms per day of hydrogen, along with site selection to include a renewable feedstock for the fuel cell, were completed in Phase 3. The system also completed six months of demonstration operation at the wastewater treatment facility operated by Orange County Sanitation District (OCSD, Fountain Valley, CA). As part of achieving the objective of operating on a renewable feedstock, Air Products secured additional funding via an award from the California Air Resources Board. The South Coast Air Quality Management District also provided cost share which supported the objectives of this project. System operation at OCSD confirmed the results from shop validation testing performed during Phase 3. Hydrogen was produced at rates and purity that met the targets from the system design basis, and coproduction efficiency exceeded the 50% target set in conjunction with input from the DOE. Hydrogen production economics, updated from the Phase 2 analysis, showed pricing of $5 to $6 per kilogram of hydrogen using current gas purification systems. Hydrogen costs under $3 per kilogram are achievable if next-generation electrochemical separation technologies become available.

Edward C. Heydorn

2012-10-26T23:59:59.000Z

284

A computer program for HVDC converter station RF noise calculations  

SciTech Connect (OSTI)

HVDC converter station operations generate radio frequency (RF) electromagnetic (EM) noise which could interfere with adjacent communication and computer equipment, and carrier system operations. A generic Radio Frequency Computer Analysis Program (RAFCAP) for calculating the EM noise generated by valve ignition of a converter station has been developed as part of a larger project. The program calculates RF voltages, currents, complex power, ground level electric field strength and magnetic flux density in and around an HVDC converter station. The program requires the converter station network to be represented by frequency dependent impedance functions. Comparisons of calculated and measured values are given for an actual HVDC station to illustrate the validity of the program. RAFCAP is designed to be used by engineers for the purpose of calculating the RF noise produced by the igniting of HVDC converter valves.

Kasten, D.G.; Caldecott, R.; Sebo, S.A. (Ohio State Univ., Columbus, OH (United States). Dept. of Electrical Engineering); Liu, Y. (Virginia Polytechnic Inst. State Univ., Blacksburg, VA (United States). Bradley Dept. of Electrical Engineering)

1994-04-01T23:59:59.000Z

285

PERFORMANCE OF A STIRLING ENGINE POWERED HEAT ACTIVATED HEAT PUMP  

E-Print Network [OSTI]

PERFORMANCE OF A STIRLING ENGINE POWERED HEAT ACTIVATED HEAT PUMP W. D. C. Richards and W. L. Auxer General Electric Company Space Division King of Prussia, Pa. ABSTRACT A heat activated heat pump (HAHP for space heating since it directly utilizes the engine waste heat in addition to the energy obtained

Oak Ridge National Laboratory

286

Integrated Gasification Combined Cycle (IGCC) demonstration project, Polk Power Station -- Unit No. 1. Annual report, October 1993--September 1994  

SciTech Connect (OSTI)

This describes the Tampa Electric Company`s Polk Power Station Unit 1 (PPS-1) Integrated Gasification Combined Cycle (IGCC) demonstration project which will use a Texaco pressurized, oxygen-blown, entrained-flow coal gasifier to convert approximately 2,300 tons per day of coal (dry basis) coupled with a combined cycle power block to produce a net 250 MW electrical power output. Coal is slurried in water, combined with 95% pure oxygen from an air separation unit, and sent to the gasifier to produce a high temperature, high pressure, medium-Btu syngas with a heat content of about 250 Btu/scf (LHV). The syngas then flows through a high temperature heat recovery unit which cools the syngas prior to its entering the cleanup systems. Molten coal ash flows from the bottom of the high temperature heat recovery unit into a water-filled quench chamber where it solidifies into a marketable slag by-product.

NONE

1995-05-01T23:59:59.000Z

287

Heating control methodology in coke oven battery at Rourkela Steel Plant  

SciTech Connect (OSTI)

A methodology of heating control was evolved incorporating temperature data generated through infra-red sensor at quenching station and thermocouples specially installed in the gooseneck of coke oven battery No. 3 of RSP. Average temperature of the red-hot coke as pushed helps in diagnosis of the abnormal ovens and in setting the targeted battery temperature. A concept of coke readiness factor (Q) was introduced which on optimization resulted in lowering the specific heat consumption by 30 KCal/Kg.

Bandyopadhyay, S.S.; Parthasarathy, L.; Gupta, A.; Bose, P.R.; Mishra, U.

1996-12-31T23:59:59.000Z

288

Thermal Energy Storage/Heat Recovery and Energy Conservation in Food Processing  

E-Print Network [OSTI]

discharges can be made more economically attrac tank holding several thousand gallons of water tive by incorporating thermal energy storage in a maintained at 128-130?F. This scald tank is con heat recovery system. Thermal energy storage can stantly... the ultimate energy end use. of wasting this hot water to the plant drain, a heat A project conducted by the Georgia Tech exchanger was installed at the Gold Kist plant to Engineering Experiment Station to demonstrate preheat scald tank makeup water...

Combes, R. S.; Boykin, W. B.

1980-01-01T23:59:59.000Z

289

Mn-Fe base and Mn-Cr-Fe base austenitic alloys  

DOE Patents [OSTI]

Manganese-iron base and manganese-chromium-iron base austenitic alloys designed to have resistance to neutron irradiation induced swelling and low activation have the following compositions (in weight percent): 20 to 40 Mn; up to about 15 Cr; about 0.4 to about 3.0 Si; an austenite stabilizing element selected from C and N, alone or in combination with each other, and in an amount effective to substantially stabilize the austenite phase, but less than about 0.7 C, and less than about 0.3 N; up to about 2.5 V; up to about 0.1 P; up to about 0.01 B; up to about 3.0 Al; up to about 0.5 Ni; up to about 2.0 W; up to about 1.0 Ti; up to about 1.0 Ta; and with the remainder of the alloy being essentially iron.

Brager, Howard R. (Richland, WA); Garner, Francis A. (Richland, WA)

1987-01-01T23:59:59.000Z

290

Compression station key to Texas pipeline project  

SciTech Connect (OSTI)

This was probably the largest pipeline project in the US last year, and the largest in Texas in the last decade. The new compressor station is a key element in this project. TECO, its servicing dealer, and compression packager worked closely throughout the planning and installation stages of the project. To handle the amount of gas required, TECO selected the GEMINI F604-1 compressor, a four-throw, single-stage unit with a six-inch stroke manufactured by Weatherford Enterra Compression Co. (WECC) in Corpus Christi, TX. TECO also chose WECC to package the compressors. Responsibility for ongoing support of the units will be shared among TECO, the service dealer and the packager. TECO is sending people to be trained by WECC, and because the G3600 family of engines is still relatively new, both the Caterpillar dealer and WECC sent people for advanced training at Caterpillar facilities in Peoria, IL. As part of its service commitment to TECO, the servicing dealer drew up a detailed product support plan, encompassing these five concerns: Training, tooling; parts support; service support; and commissioning.

NONE

1996-10-01T23:59:59.000Z

291

Heat pump system  

DOE Patents [OSTI]

An air heating and cooling system for a building includes an expansion type refrigeration circuit and a vapor power circuit. The refrigeration circuit includes two heat exchangers, one of which is communicated with a source of indoor air from the building and the other of which is communicated with a source of air from outside the building. The vapor power circuit includes two heat exchangers, one of which is disposed in series air flow relationship with the indoor refrigeration circuit heat exchanger and the other of which is disposed in series air flow relationship with the outdoor refrigeration circuit heat exchanger. Fans powered by electricity generated by a vapor power circuit alternator circulate indoor air through the two indoor heat exchangers and circulate outside air through the two outdoor heat exchangers. The system is assembled as a single roof top unit, with a vapor power generator and turbine and compressor thermally insulated from the heat exchangers, and with the indoor heat exchangers thermally insulated from the outdoor heat exchangers.

Swenson, Paul F. (Shaker Heights, OH); Moore, Paul B. (Fedhaven, FL)

1983-01-01T23:59:59.000Z

292

Heat pump system  

DOE Patents [OSTI]

An air heating and cooling system for a building includes an expansion type refrigeration circuit and a vapor power circuit. The refrigeration circuit includes two heat exchangers, one of which is communicated with a source of indoor air from the building and the other of which is communicated with a source of air from outside the building. The vapor power circuit includes two heat exchangers, one of which is disposed in series air flow relationship with the indoor refrigeration circuit heat exchanger and the other of which is disposed in series air flow relationship with the outdoor refrigeration circuit heat exchanger. Fans powered by electricity generated by a vapor power circuit alternator circulate indoor air through the two indoor heat exchangers and circulate outside air through the two outdoor heat exchangers. The system is assembled as a single roof top unit, with a vapor power generator and turbine and compressor thermally insulated from the heat exchangers, and with the indoor heat exchangers thermally insulated from the outdoor heat exchangers.

Swenson, Paul F.; Moore, Paul B.

1983-06-21T23:59:59.000Z

293

Early Station Costs Questionnaire | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeat PumpRecord ofESPC ENABLE: ECM Summary ECM Included NotFederal4 - InMaterialEarly

294

Krafla Geothermal Power Station | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpInc Place:Keystone Clean Air JumpMaine. Its FIPSJVII & III

295

Policies supporting Heat Pump Technologies  

E-Print Network [OSTI]

Policies supporting Heat Pump Technologies in Canada IEA Heat Pump Workshop London, UK November 13 in the world, with an average of 16,995 kilowatt-hours per annum. #12;Canada's Context for Heat Pumps Impacts avenues: Ground source heat pumps for cold climates (heating and cooling) Reversible air source heat

Oak Ridge National Laboratory

296

Solar-Assisted Electric Vehicle Charging Station Interim Report  

SciTech Connect (OSTI)

Oak Ridge National Laboratory (ORNL) has been awarded $6.8 million in the Department of Energy (DOE) American Recovery and Reinvestment Act (ARRA) funds as part of an overall $114.8 million ECOtality grant with matching funds from regional partners to install 125 solar-assisted Electric Vehicle (EV) charging stations across Knoxville, Nashville, Chattanooga, and Memphis. Significant progress has been made toward completing the scope with the installation of 25 solar-assisted charging stations at ORNL; six stations at Electric Power Research Institute (EPRI); and 27 stations at Nissan's Smyrna and Franklin sites, with three more stations under construction at Nissan's new lithium-ion battery plant. Additionally, the procurement process for contracting the installation of 34 stations at Knoxville, the University of Tennessee Knoxville (UTK), and Nashville sites is underway with completion of installation scheduled for early 2012. Progress is also being made on finalizing sites and beginning installations of 30 stations in Nashville, Chattanooga, and Memphis by EPRI and Tennessee Valley Authority (TVA). The solar-assisted EV charging station project has made great strides in fiscal year 2011. A total of 58 solar-assisted EV parking spaces have been commissioned in East and Middle Tennessee, and progress on installing the remaining 67 spaces is well underway. The contract for the 34 stations planned for Knoxville, UTK, and Nashville should be underway in October with completion scheduled for the end of March 2012; the remaining three Nissan stations are under construction and scheduled to be complete in November; and the EPRI/TVA stations for Chattanooga, Vanderbilt, and Memphis are underway and should be complete by the end of March 2012. As additional Nissan LEAFs are being delivered, usage of the charging stations has increased substantially. The project is on course to complete all 125 solar-assisted EV charging stations in time to collect meaningful data by the end of government fiscal year 2012. Lessons learned from the sites completed thus far are being incorporated and are proving to be invaluable in completion of the remaining sites.

Lapsa, Melissa Voss [ORNL; Durfee, Norman [ORNL; Maxey, L Curt [ORNL; Overbey, Randall M [ORNL

2011-09-01T23:59:59.000Z

297

ALISON SEXTON 52 Groveland Terrace, #105 | Minneapolis, MN, 55403  

E-Print Network [OSTI]

: The Case of Solar Panel Heating Systems" (with Steven Sexton) PUBLICATIONS FOR GENERAL AUDIENCES Taking

Levinson, David M.

298

LiMnPO4 Nanoplate Grown via Solid-State Reaction in Molten Hydrocarbon...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

LiMnPO4 Nanoplate Grown via Solid-State Reaction in Molten Hydrocarbon for Li-ion Battery Cathode. LiMnPO4 Nanoplate Grown via Solid-State Reaction in Molten Hydrocarbon for Li-ion...

299

Electrodeposited Al-Mn Alloys with Microcrystalline, Nanocrystalline, Amorphous and Nano-quasicrystalline Structures  

E-Print Network [OSTI]

Al–Mn alloys with Mn content ranging from 0 to 15.8 at.% are prepared by electrodeposition from an ionic liquid at room temperature, and exhibit a remarkably broad range of structures. The alloys are characterized through ...

Ruan, Shiyun

300

Distinct local electronic structure and magnetism for Mn in amorphous Si and Ge  

E-Print Network [OSTI]

Li, A. P. et al. Magnetism in Mn x Ge 1-x semiconductorsElectronic Structure and Magnetism for Mn in Amorphous Sistructure that determines magnetism. Figure 3 shows XAS data

Zeng, Li

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Mn12-acetate thin film patterns and their interaction with superconductors  

E-Print Network [OSTI]

Mn12-acetate single-molecule magnets (SMMs) are nano-scale magnets showing a strong magnetic anisotropy, slow relaxation and stepwise magnetic hysteresis curves. Possible applications of Mn12-acetate, e.g. for ultra high density magnetic information...

Kim, Kyongwan

2009-05-15T23:59:59.000Z

302

On deformation twinning in a 17.5%Mn-TWIP steel: A physically...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

On deformation twinning in a 17.5%Mn-TWIP steel: A physically-based phenomenological model. On deformation twinning in a 17.5%Mn-TWIP steel: A physically-based phenomenological...

303

Pulsed laser deposition of Mn doped CdSe quantum dots for improved solar cell performance  

SciTech Connect (OSTI)

In this work, we demonstrate (1) a facile method to prepare Mn doped CdSe quantum dots (QDs) on Zn{sub 2}SnO{sub 4} photoanodes by pulsed laser deposition and (2) improved device performance of quantum dot sensitized solar cells of the Mn doped QDs (CdSe:Mn) compared to the undoped QDs (CdSe). The band diagram of photoanode Zn{sub 2}SnO{sub 4} and sensitizer CdSe:Mn QD is proposed based on the incident-photon-to-electron conversion efficiency (IPCE) data. Mn-modified band structure leads to absorption at longer wavelengths than the undoped CdSe QDs, which is due to the exchange splitting of the CdSe:Mn conduction band by the Mn dopant. Three-fold increase in the IPCE efficiency has also been observed for the Mn doped samples.

Dai, Qilin; Wang, Wenyong, E-mail: wwang5@uwyo.edu, E-mail: jtang2@uwyo.edu; Tang, Jinke, E-mail: wwang5@uwyo.edu, E-mail: jtang2@uwyo.edu [Department of Physics and Astronomy, University of Wyoming, Laramie, Wyoming 82071 (United States); Sabio, Erwin M. [Department of Chemistry, University of Wyoming, Laramie, Wyoming 82071 (United States)

2014-05-05T23:59:59.000Z

304

Engineering the magnetic properties of the Mn13 cluster by doping  

E-Print Network [OSTI]

With a goal to produce a giant magnetic moment in a Mn13 cluster that will be useful for practical applications, we have considered the structure and magnetic properties of a pure Mn13 cluster and substitutionally doped ...

Datta, Soumendu

305

X-ray absorption study of the electronic structure of Mn-doped amorphous Si  

E-Print Network [OSTI]

X-ray absorption study of the electronic structure of Mn-?x ) is studied by X-ray absorption spectroscopy at the Mn Land featureless L 3,2 absorption peaks, corresponding to an

Zeng, Li

2008-01-01T23:59:59.000Z

306

E-Print Network 3.0 - al fe mn Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

National Cheng Kung University Collection: Physics 4 Valence states of transition-metal ions in cubic perovskites SrMn1-xFexO3 H. J. Lee,a Summary: the Mn 3d resonance and...

307

Fluidized bed heat treating system  

DOE Patents [OSTI]

Systems for heat treating materials are presented. The systems typically involve a fluidized bed that contains granulated heat treating material. In some embodiments a fluid, such as an inert gas, is flowed through the granulated heat treating medium, which homogenizes the temperature of the heat treating medium. In some embodiments the fluid may be heated in a heating vessel and flowed into the process chamber where the fluid is then flowed through the granulated heat treating medium. In some embodiments the heat treating material may be liquid or granulated heat treating material and the heat treating material may be circulated through a heating vessel into a process chamber where the heat treating material contacts the material to be heat treated. Microwave energy may be used to provide the source of heat for heat treating systems.

Ripley, Edward B; Pfennigwerth, Glenn L

2014-05-06T23:59:59.000Z

308

Water-heating dehumidifier  

DOE Patents [OSTI]

A water-heating dehumidifier includes a refrigerant loop including a compressor, at least one condenser, an expansion device and an evaporator including an evaporator fan. The condenser includes a water inlet and a water outlet for flowing water therethrough or proximate thereto, or is affixed to the tank or immersed into the tank to effect water heating without flowing water. The immersed condenser design includes a self-insulated capillary tube expansion device for simplicity and high efficiency. In a water heating mode air is drawn by the evaporator fan across the evaporator to produce cooled and dehumidified air and heat taken from the air is absorbed by the refrigerant at the evaporator and is pumped to the condenser, where water is heated. When the tank of water heater is full of hot water or a humidistat set point is reached, the water-heating dehumidifier can switch to run as a dehumidifier.

Tomlinson, John J. (Knoxville, TN)

2006-04-18T23:59:59.000Z

309

Disentangling the Mn moments on different sublattices in the half-metallic ferrimagnet Mn3?xCoxGa  

SciTech Connect (OSTI)

Ferrimagnetic Mn{sub 3-x}Co{sub x}Ga compounds have been investigated by magnetic circular dichroism in x-ray absorption (XMCD). Compounds with x > 0.5 crystallize in the CuHg{sub 2}Ti structure. A tetragonal distortion of the cubic structure occurs for x {le} 0.5. For the cubic phase, magnetometry reveals a linearly increasing magnetization of 2x Bohr magnetons per formula unit obeying the generalized Slater-Pauling rule. XMCD confirms the ferrimagnetic character with Mn atoms occupying two different sublattices with antiparallel spin orientation and different degrees of spin localization and identifies the region 0.6 < x {le} 0.8 as most promising for a high spin polarization at the Fermi level. Individual Mn moments on inequivalent sites are compared to theoretical predictions.

Klaer, P.; Jenkins, C.A.; Alijani, V.; Winterlik, J.; Balke, B.; Felser, C.; Elmers, H.J.

2011-05-03T23:59:59.000Z

310

Design of high pressure metering and regulating stations  

SciTech Connect (OSTI)

Metering and regulating stations effectively serve as the cash registers of the natural gas industry. While the potential for lost revenue resulting from improper design is a serious consideration, it is not the only one. The potential exists for problems such as excessive noise levels, inaccurate reflection of lost and unaccounted-for gas, and numerous potentially hazardous situations. The best time to limit the potential for problems is during the design process. This, together with the critical nature of these stations, dictates that proper design is imperative. Proper design of metering and regulating stations is a constantly changing and extremely complicated subject. There are virtually an infinite number of situations that the designer can encounter in evaluating his design. In view of this, it is impossible to develop a cookbook method of designing these stations that covers all possible situations. The emphasis of this paper is to briefly touch on the major aspects of metering and regulating station design. Steps involved in station design are: 1. Collection of data on the proposed station. 2. Determination of piping configuration. 3. Selection of measurement equipment. 4. Selection of pressure regulating and overpressure protection equipment. 5. Communication of the final design to field personnel.

Rehler, D.A. [Oklahoma Natural Gas Co., Enid, OK (United States)

1995-12-01T23:59:59.000Z

311

Mechanical Compression Heat Pumps  

E-Print Network [OSTI]

MECHANICAL COMPRESSION HEAT PUMPS Thomas-L. Apaloo and K. Kawamura Mycom Corporation, Los Angeles, California J. Matsuda, Mayekawa Mfg. Co., Tokyo, Japan ABSTRACT Mechanical compression heat pumping is not new in industrial applications.... In fact, industry history suggests that the theoretical concept was developed before 1825. Heat pump manufacturers gained the support of consultants and end-users when the energy crisis hit this country in 1973. That interest, today, has been...

Apaloo, T. L.; Kawamura, K.; Matsuda, J.

312

Heat storage duration  

SciTech Connect (OSTI)

Both the amount and duration of heat storage in massive elements of a passive building are investigated. Data taken for one full winter in the Balcomb solar home are analyzed with the aid of sub-system simulation models. Heat storage duration is tallied into one-day intervals. Heat storage location is discussed and related to overall energy flows. The results are interpreted and conclusions drawn.

Balcomb, J.D.

1981-01-01T23:59:59.000Z

313

Solar Heating in Uppsala.  

E-Print Network [OSTI]

?? The housing corporation Uppsalahem has installed asolar heating system in the neighbourhood Haubitsen,which was renovated in 2011. This report examineshow much energy the solar… (more)

Blomqvist, Emelie; Häger, Klara

2012-01-01T23:59:59.000Z

314

Solar heating in Colombia.  

E-Print Network [OSTI]

?? This report describes the process of a thesis implemented in Colombia concerning solar energy. The project was to install a self-circulating solar heating system,… (more)

Skytt, Johanna

2012-01-01T23:59:59.000Z

315

Waste Heat Recovery  

Office of Environmental Management (EM)

DRAFT - PRE-DECISIONAL - DRAFT 1 Waste Heat Recovery 1 Technology Assessment 2 Contents 3 1. Introduction to the TechnologySystem ......

316

Heat and mass exchanger  

DOE Patents [OSTI]

A mass and heat exchanger includes at least one first substrate with a surface for supporting a continuous flow of a liquid thereon that either absorbs, desorbs, evaporates or condenses one or more gaseous species from or to a surrounding gas; and at least one second substrate operatively associated with the first substrate. The second substrate includes a surface for supporting the continuous flow of the liquid thereon and is adapted to carry a heat exchange fluid therethrough, wherein heat transfer occurs between the liquid and the heat exchange fluid.

Lowenstein, Andrew (Princeton, NJ); Sibilia, Marc J. (Princeton, NJ); Miller, Jeffrey A. (Hopewell, NJ); Tonon, Thomas (Princeton, NJ)

2007-09-18T23:59:59.000Z

317

Heat and mass exchanger  

DOE Patents [OSTI]

A mass and heat exchanger includes at least one first substrate with a surface for supporting a continuous flow of a liquid thereon that either absorbs, desorbs, evaporates or condenses one or more gaseous species from or to a surrounding gas; and at least one second substrate operatively associated with the first substrate. The second substrate includes a surface for supporting the continuous flow of the liquid thereon and is adapted to carry a heat exchange fluid therethrough, wherein heat transfer occurs between the liquid and the heat exchange fluid.

Lowenstein, Andrew (Princeton, NJ); Sibilia, Marc J. (Princeton, NJ); Miller, Jeffrey A. (Hopewell, NJ); Tonon, Thomas (Princeton, NJ)

2011-06-28T23:59:59.000Z

318

HEATS: Thermal Energy Storage  

SciTech Connect (OSTI)

HEATS Project: The 15 projects that make up ARPA-E’s HEATS program, short for “High Energy Advanced Thermal Storage,” seek to develop revolutionary, cost-effective ways to store thermal energy. HEATS focuses on 3 specific areas: 1) developing high-temperature solar thermal energy storage capable of cost-effectively delivering electricity around the clock and thermal energy storage for nuclear power plants capable of cost-effectively meeting peak demand, 2) creating synthetic fuel efficiently from sunlight by converting sunlight into heat, and 3) using thermal energy storage to improve the driving range of electric vehicles (EVs) and also enable thermal management of internal combustion engine vehicles.

None

2012-01-01T23:59:59.000Z

319

Heat rejection system  

DOE Patents [OSTI]

A cooling system for rejecting waste heat consists of a cooling tower incorporating a plurality of coolant tubes provided with cooling fins and each having a plurality of cooling channels therein, means for directing a heat exchange fluid from the power plant through less than the total number of cooling channels to cool the heat exchange fluid under normal ambient temperature conditions, means for directing water through the remaining cooling channels whenever the ambient temperature rises above the temperature at which dry cooling of the heat exchange fluid is sufficient and means for cooling the water.

Smith, Gregory C. (Richland, WA); Tokarz, Richard D. (Richland, WA); Parry, Jr., Harvey L. (Richland, WA); Braun, Daniel J. (Richland, WA)

1980-01-01T23:59:59.000Z

320

Passive solar space heating  

SciTech Connect (OSTI)

An overview of passive solar space heating is presented indicating trends in design, new developments, performance measures, analytical design aids, and monitored building results.

Balcomb, J.D.

1980-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

OPTIMIZING PERFORMANCE OF THE HESKETT STATION  

SciTech Connect (OSTI)

The overall conclusion from this work is that a switch from river sand bed material to limestone at the R.M. Heskett Station would provide substantial benefits to MDU. A switch to limestone would increase the fuel flexibility of the unit, allowing fuels higher in both sodium and sulfur to be burned. The limestone bed can tolerate a much higher buildup of sodium in the bed without agglomeration, allowing either the bed turnover rate to be reduced to half the current sand feed rate for a fuel with equivalent sodium or allow a higher sodium fuel to be burned with limestone feed rates equivalent to the current sand feed rate. Both stack and ambient SO{sub 2} emissions can be controlled. A small improvement in boiler efficiency should be achievable by operating at lower excess oxygen levels at low load. This reduction in oxygen will also lower NO{sub x} emissions, providing a margin of safety for meeting emission standards. No detrimental effects of using limestone at the Heskett Station were uncovered as a result of the test burn. Some specific conclusions from this work include the following: The bed material feed rate can be reduced from the current rate of 5.4% of the coal feed rate (57.4 tons of sand/day) to 2.5% of the coal feed rate (27 tons of limestone/day). This will result in an annual savings of approximately $200,000. (1) SO{sub 2} emissions at the recommended feed rate would be approximately 250 ppm (0.82 lb/MMBtu) using a similar lignite. Based on the cost of the limestones, SO{sub 2} allowances could be generated at a cost of $60/ton SO{sub 2} , leaving a large profit margin for the sale of allowances. The addition of limestone at the same rate currently used for sand feed could generate $455,000 net income if allowances are sold at $200/ton SO2 . (2) At full-load operation, unburned carbon losses increase significantly at excess oxygen levels below 2.8%. No efficiency gains are expected at high-load operation by switching from sand to limestone. By reducing the oxygen level at low load to 8.5%, an efficiency gain of approximately 1.2% could be realized, equating to $25,000 to $30,000 in annual savings. (3) A reduction of 25 tons/day total ash (bed material plus fly ash) will be realized by using limestone at the recommended feed rate compared to the current sand feed rate. No measurable change in volume would be realized because of the lower bulk density of the limestone-derived material.

Michael D. Mann; Ann K. Henderson

1999-03-01T23:59:59.000Z

322

Novel frustrated magnetic lattice based on triangular [Mn3(m3-F)] clusters with tetrazole ligands{  

E-Print Network [OSTI]

Novel frustrated magnetic lattice based on triangular [Mn3(m3-F)] clusters with tetrazole ligands701840a Unprecedented [MnII 3(m3-F)(m-N­N)3] triangular clusters with tetrazole ligands are linked by Mn the tetrazolate ligands, which possess additional N-donor sites for network formation. To our knowledge, [M3(m3-X

Gao, Song

323

On the role of Mn(IV) vacancies in the photoreductive dissolution of hexagonal birnessite  

SciTech Connect (OSTI)

Photoreductive dissolution of layer type Mn(IV) oxides (birnessite) under sunlight illumination to form soluble Mn(II) has been observed in both field and laboratory settings, leading to a consensus that this process is a key driver of the biogeochemical cycling of Mn in the euphotic zones of marine and freshwater ecosystems. However, the underlying mechanisms for the process remain unknown, although they have been linked to the semiconducting characteristics of hexagonal birnessite, the ubiquitous Mn(IV) oxide produced mainly by bacterial oxidation of soluble Mn(II). One of the universal properties of this biogenic mineral is the presence of Mn(IV) vacancies, long-identified as strong adsorption sites for metal cations. In this paper, the possible role of Mn vacancies in photoreductive dissolution is investigated theoretically using quantum mechanical calculations based on spin-polarized density functional theory (DFT). Our DFT study demonstrates unequivocally that Mn vacancies significantly reduce the band-gap energy for hexagonal birnessite relative to a hypothetical vacancy-free MnO{sub 2} and thus would increase the concentration of photo-induced electrons available for Mn(IV) reduction upon illumination of the mineral by sunlight. Calculations of the charge distribution in the presence of vacancies, although not fully conclusive, show a clear separation of photo-induced electrons and holes, implying a slow recombination of these charge-carriers that facilitates the two-electron reduction of Mn(IV) to Mn(II).

Kwon, K.D.; Refson, K.; Sposito, G.

2009-06-01T23:59:59.000Z

324

Thermochromic effect at room temperature of Sm{sub 0.5}Ca{sub 0.5}MnO{sub 3} thin films  

SciTech Connect (OSTI)

Sm{sub 0.5}Ca{sub 0.5}MnO{sub 3} thermochromic thin films were synthesized using dc reactive magnetron co-sputtering and subsequent annealing in air. The film structure was studied by x-ray diffraction analysis. To validate the thermochromic potentiality of Sm{sub 0.5}Ca{sub 0.5}MnO{sub 3}, electrical resistivity and infrared transmittance spectra were recorded for temperatures ranging from 77 K to 420 K. The temperature dependence of the optical band gap was estimated in the near infrared range. Upon heating, the optical transmission decreases in the infrared domain showing a thermochromic effect over a wide wavelength range at room temperature.

Boileau, A.; Capon, F.; Barrat, S.; Pierson, J. F. [Universite de Lorraine, Institut Jean Lamour, Departement CP2S, UMR CNRS 7198, Nancy, F-54042 (France); Laffez, P. [Groupe de Recherche Electronique, Materiaux, Acoustique, Nanoscience (GREMAN), Universite Francois Rabelais de Tours, UMR CNRS 7347, IUT de Blois, 15 rue de la Chocolaterie, Blois, F-41000 (France)

2012-06-01T23:59:59.000Z

325

Buried waste integrated demonstration human engineered control station. Final report  

SciTech Connect (OSTI)

This document describes the Human Engineered Control Station (HECS) project activities including the conceptual designs. The purpose of the HECS is to enhance the effectiveness and efficiency of remote retrieval by providing an integrated remote control station. The HECS integrates human capabilities, limitations, and expectations into the design to reduce the potential for human error, provides an easy system to learn and operate, provides an increased productivity, and reduces the ultimate investment in training. The overall HECS consists of the technology interface stations, supporting engineering aids, platform (trailer), communications network (broadband system), and collision avoidance system.

Not Available

1994-09-01T23:59:59.000Z

326

Detailed Analysis of Urban Station Siting for California Hydrogen Highway Network  

E-Print Network [OSTI]

www.energy.ca.gov/gasoline/gasoline_stations/index.html.estimates range from 10% of existing gasoline stations to30% of gasoline stations. Two of the studies[7,8] further

Nicholas, Michael A; Ogden, Joan M

2007-01-01T23:59:59.000Z

327

Bridging the Gap Between Transportation and Stationary Power: Hydrogen Energy Stations and their Implications for the Transportation Sector  

E-Print Network [OSTI]

Economic Analysis of Hydrogen Energy Station Concepts,E 2 Four Potential Types of Hydrogen Energy Stations VehicleOperational Toronto Hydrogen Energy Station Stationary PEMFC

Weinert, Jonathan X.; Lipman, Timothy; Unnasch, Stephen

2005-01-01T23:59:59.000Z

328

Magnetic properties and magnetocaloric effect of NdMn{sub 2?x}Cu{sub x}Si{sub 2} compounds  

SciTech Connect (OSTI)

Structural and magnetic properties of NdMn{sub 2?x}Cu{sub x}Si{sub 2} compounds (x?=?0–1.0) have been investigated by high intensity x-ray and resolution neutron diffraction (3–450?K), specific heat, dc magnetization, and differential scanning calorimetry measurements. Substitution of Cu for Mn leads to an increase in the lattice parameter a but a decrease in c at room temperature. Two magnetic phase transitions have been found for NdMn{sub 2?x}Cu{sub x}Si{sub 2} compounds with T{sub N} for the antiferromagnetic ordering of Mn-sublatttice and T{sub C} for the Nd-sublattice ferromagnetic ordering, respectively. T{sub C} increases significantly with increasing Cu content from 36?K at x?=?0 to 100?K at x?=?1.0. Moreover, it is found that the order of magnetic phase transition around T{sub C} also changes from first order at x?Mn. The values of ??S{sub M} around T{sub C} decrease with increasing x from 27?J kg{sup ?1} K{sup ?1} for x?=?0 to 0.5?J kg{sup ?1} K{sup ?1} for x?=?1.0 under 0–5?T field. Refinement of neutron diffraction patterns for x?=?0.2 confirms the magnetic states detected by magnetic study and also indicates that the lattice constants a and c show a distinct variation around T{sub C}.

Md Din, M. F., E-mail: mfmd999@uowmail.edu.au [Institute for Superconductivity and Electronic Materials, University of Wollongong, Wollongong, NSW 2522 (Australia); Department of Electrical and Electronic Engineering, Faculty of Engineering, National Defence University of Malaysia, Kem Sungai Besi, 57000 Kuala Lumpur (Malaysia); Wang, J. L. [Institute for Superconductivity and Electronic Materials, University of Wollongong, Wollongong, NSW 2522 (Australia); Bragg Institute, ANSTO, Lucas Heights, NSW 2234 (Australia); Avdeev, M.; Kennedy, S. J. [Bragg Institute, ANSTO, Lucas Heights, NSW 2234 (Australia); Gu, Q. F. [Australian Synchrotron, 800 Blackburn Rd, Clayton 3168 (Australia); Zeng, R.; Dou, S. X. [Institute for Superconductivity and Electronic Materials, University of Wollongong, Wollongong, NSW 2522 (Australia); Campbell, S. J. [School of Physical, Environmental and Mathematical Sciences, The University of New South Wales, Canberra, ACT 2600 (Australia)

2014-05-07T23:59:59.000Z

329

Cationic disorder and Mn{sup 3+}/Mn{sup 4+} charge ordering in the B? and B? sites of Ca{sub 3}Mn{sub 2}NbO{sub 9} perovskite: a comparison with Ca{sub 3}Mn{sub 2}WO{sub 9}  

SciTech Connect (OSTI)

We describe the preparation, crystal structure determination, magnetic and transport properties of two novel Mn-containing perovskites, with a different electronic configuration for Mn atoms located in B site. Ca{sub 3}Mn{sup 3+}{sub 2}WO{sub 9} and Ca{sub 3}Mn{sup 3+/4+}{sub 2}NbO{sub 9} were synthesized by standard ceramic procedures; the crystallographic structure was studied from X-ray powder diffraction (XRPD) and neutron powder diffraction (NPD). Both phases exhibit a monoclinic symmetry (S.G.: P2{sub 1}/n); Ca{sub 3}Mn{sub 2}WO{sub 9} presents a long-range ordering over the B sites, whereas Ca{sub 3}Mn{sub 2}NbO{sub 9} is strongly disordered. By “in-situ” NPD, the temperature evolution of the structure study presents an interesting evolution in the octahedral size (?Mn–O?) for Ca{sub 3}Mn{sub 2}NbO{sub 9}, driven by a charge ordering effect between Mn{sup 3+} and Mn{sup 4+} atoms, related to the anomaly observed in the transport measurements at T?160 K. Both materials present a magnetic order below T{sub C}=30 K and 40 K for W and Nb materials, respectively. The magneto-transport measurements display non-negligible magnetoresistance properties in the paramagnetic regime. - Graphical abstract: Comparison between the octahedron size and the magnetic behaviour for Ca{sub 3}Mn{sub 2}NbO{sub 9} in the temperature region where the charge and magnetic order occur. Display Omitted - Highlights: • Two novel Mn-containing double perovskites were obtained by solid-state reactions. • Both double perovskites are monoclinic (P2{sub 1}/n) determined by XRPD and NPD. • Ca{sub 3}Mn{sub 2}WO{sub 9} contains Mn{sup 3+} while Ca{sub 3}Mn{sub 2}NbO{sub 9} includes mixed-valence cations Mn{sup 3+}/Mn{sup 4+}. • Ca{sub 3}Mn{sub 2}NbO{sub 9} presents a charge-ordering effect between Mn{sup 3+} and Mn{sup 4+} evidenced by NPD. • The magnetic and transport studies evidenced the charge ordering in Ca{sub 3}Mn{sub 2}NbO{sub 9}.

López, C.A., E-mail: calopez@unsl.edu.ar [INTEQUI-Área de Química General e Inorgánica “Dr. G. F. Puelles”, Facultad de Química, Bioquímica y Farmacia, Universidad Nacional de San Luis, Chacabuco y Pedernera, 5700 San Luis (Argentina); Centro Atómico Bariloche, Comisión Nacional de Energía Atómica and Instituto Balseiro, Universidad Nacional de Cuyo, 8400S.C. de Bariloche, Río Negro (Argentina); Saleta, M.E. [Centro Atómico Bariloche, Comisión Nacional de Energía Atómica and Instituto Balseiro, Universidad Nacional de Cuyo, 8400S.C. de Bariloche, Río Negro (Argentina); Pedregosa, J.C. [INTEQUI-Área de Química General e Inorgánica “Dr. G. F. Puelles”, Facultad de Química, Bioquímica y Farmacia, Universidad Nacional de San Luis, Chacabuco y Pedernera, 5700 San Luis (Argentina); Sánchez, R.D. [Centro Atómico Bariloche, Comisión Nacional de Energía Atómica and Instituto Balseiro, Universidad Nacional de Cuyo, 8400S.C. de Bariloche, Río Negro (Argentina); Alonso, J.A. [Instituto de Ciencia de Materiales de Madrid, CSIC, Cantoblanco, E-28049 Madrid (Spain); and others

2014-02-15T23:59:59.000Z

330

SOARCA Peach Bottom Atomic Power Station Long-Term Station Blackout Uncertainty Analysis: Knowledge Advancement.  

SciTech Connect (OSTI)

This paper describes the knowledge advancements from the uncertainty analysis for the State-of- the-Art Reactor Consequence Analyses (SOARCA) unmitigated long-term station blackout accident scenario at the Peach Bottom Atomic Power Station. This work assessed key MELCOR and MELCOR Accident Consequence Code System, Version 2 (MACCS2) modeling uncertainties in an integrated fashion to quantify the relative importance of each uncertain input on potential accident progression, radiological releases, and off-site consequences. This quantitative uncertainty analysis provides measures of the effects on consequences, of each of the selected uncertain parameters both individually and in interaction with other parameters. The results measure the model response (e.g., variance in the output) to uncertainty in the selected input. Investigation into the important uncertain parameters in turn yields insights into important phenomena for accident progression and off-site consequences. This uncertainty analysis confirmed the known importance of some parameters, such as failure rate of the Safety Relief Valve in accident progression modeling and the dry deposition velocity in off-site consequence modeling. The analysis also revealed some new insights, such as dependent effect of cesium chemical form for different accident progressions. (auth)

Gauntt, Randall O.; Mattie, Patrick D.; Bixler, Nathan E.; Ross, Kyle; Cardoni, Jeffrey N; Kalinich, Donald A.; Osborn, Douglas M.; Sallaberry, Cedric Jean-Marie; Ghosh, S. Tina

2014-02-01T23:59:59.000Z

331

Growing the renewable chemicals and advanced biofuels cluster in MN  

E-Print Network [OSTI]

Growing the renewable chemicals and advanced biofuels cluster in MN #12;Renewable Chemical Value% Reduction 60% Reduction 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Gasoline Corn Ethanol Advanced Biofuel Cellulosic Biofuel Corn Ethanol 20% GHG Reduction Compared to gasoline: Advanced Biofuel 50% GHG Reduction e

Levinson, David M.

332

Electronic interactions between gold films and mn12-acetate  

E-Print Network [OSTI]

the presence of a surface layer of Mn12–acetate, have been performed using a dilution refrigerator. Quantitative fits to the data using the predictions of weak localization theory were performed using a least-squares fit method in order to determine...

Means, Joel Lewis

2009-05-15T23:59:59.000Z

333

Mn/DOT's Ombudsman Program Collaboration and Process  

E-Print Network [OSTI]

Mn/DOT's Ombudsman Program Collaboration and Process #12;Overview Ombudsman exists to rebuild trust on the environmental and municipal consent processes can be critical #12;A Large Organization #12;Tragedy;Ombudsman Does Not... ·! Advocate for one party or point of view ·! Own any formal process or policy

Minnesota, University of

334

Heat pipes and use of heat pipes in furnace exhaust  

DOE Patents [OSTI]

An array of a plurality of heat pipe are mounted in spaced relationship to one another with the hot end of the heat pipes in a heated environment, e.g. the exhaust flue of a furnace, and the cold end outside the furnace. Heat conversion equipment is connected to the cold end of the heat pipes.

Polcyn, Adam D. (Pittsburgh, PA)

2010-12-28T23:59:59.000Z

335

Proceedings of Heat Transfer 2003: ASME Summer Heat Transfer Conference  

E-Print Network [OSTI]

Proceedings of Heat Transfer 2003: ASME Summer Heat Transfer Conference Las Vegas, Nevada, USA July 21-23, 2003 HT2003-47449 HEAT TRANSFER FROM A MOVING AND EVAPORATING MENISCUS ON A HEATED SURFACE meniscus with complete evaporation of water without any meniscus break-up. The experimental heat transfer

Kandlikar, Satish

336

IMPLEMENTING GROUND SOURCE HEAT PUMP AND GROUND LOOP HEAT EXCHANGER  

E-Print Network [OSTI]

IMPLEMENTING GROUND SOURCE HEAT PUMP AND GROUND LOOP HEAT EXCHANGER MODELS IN THE ENERGYPLUS #12;ii IMPLEMENTING GROUND SOURCE HEAT PUMP AND GROUND LOOP HEAT EXCHANGER MODELS IN THE ENERGYPLUS............................................................... 2 1.3. Overview of the Parameter Estimation Water-to-Water Heat Pump Model ........... 5 1

337

First university owned district heating system using biomass heat  

E-Print Network [OSTI]

Highlights · First university owned district heating system using biomass heat · Capacity: 15 MMBtu Main Campus District Heating Performance · Avoided: 3500 tonnes of CO2 · Particulate: less than 10 mg District Heating Goals To displace 85% of natural gas used for core campus heating. Fuel Bunker Sawmill

Northern British Columbia, University of

338

E-Print Network 3.0 - air station usa Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and WALD, Lucien. Adding virtual measuring stations to a network for urban air pollution Summary: , and WALD, Lucien. Adding virtual measuring stations to a network for...

339

Cranberry Station Celebrates 100th Anniversary with a 100 Year Endowment  

E-Print Network [OSTI]

Cranberry Station Celebrates 100th Anniversary with a 100 Year Endowment The Cranberry Station established with contributions from growers, friends, ag companies, and cranberry handlers. The funds

Massachusetts at Amherst, University of

340

Vision for Rollout of Fuel Cell Vehicles and Hydrogen Fuel Stations...  

Office of Environmental Management (EM)

Vision for Rollout of Fuel Cell Vehicles and Hydrogen Fuel Stations Vision for Rollout of Fuel Cell Vehicles and Hydrogen Fuel Stations This document establishes the California...

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Tri-Generation Success Story: World's First Tri-Gen EnergyStation...  

Energy Savers [EERE]

Energy Department, the Fountain Valley energy station is the world's first tri-generation hydrogen energy and electrical power station to provide transportation fuel to the public...

342

Survey Results and Analysis of the Cost and Efficiency of Various Operating Hydrogen Fueling Stations  

SciTech Connect (OSTI)

Existing Hydrogen Fueling Stations were surveyed to determine capital and operational costs. Recommendations for cost reduction in future stations and for research were developed.

Cornish, John

2011-03-05T23:59:59.000Z

343

Chemical heat pump  

DOE Patents [OSTI]

A chemical heat pump system is disclosed for use in heating and cooling structures such as residences or commercial buildings. The system is particularly adapted to utilizing solar energy, but also increases the efficiency of other forms of thermal energy when solar energy is not available. When solar energy is not available for relatively short periods of time, the heat storage capacity of the chemical heat pump is utilized to heat the structure, as during nighttime hours. The design also permits home heating from solar energy when the sun is shining. The entire system may be conveniently rooftop located. In order to facilitate installation on existing structures, the absorber and vaporizer portions of the system may each be designed as flat, thin wall, thin pan vessels which materially increase the surface area available for heat transfer. In addition, this thin, flat configuration of the absorber and its thin walled (and therefore relatively flexible) construction permits substantial expansion and contraction of the absorber material during vaporization and absorption without generating voids which would interfere with heat transfer.

Greiner, Leonard (2853-A Hickory Pl., Costa Mesa, CA 92626)

1981-01-01T23:59:59.000Z

344

Chemical heat pump  

DOE Patents [OSTI]

A chemical heat pump system is disclosed for use in heating and cooling structures such as residences or commercial buildings. The system is particularly adapted to utilizing solar energy, but also increases the efficiency of other forms of thermal energy when solar energy is not available. When solar energy is not available for relatively short periods of time, the heat storage capacity of the chemical heat pump is utilized to heat the structure, as during nighttime hours. The design also permits home heating from solar energy when the sun is shining. The entire system may be conveniently rooftop located. In order to facilitate intallation on existing structures, the absorber and vaporizer portions of the system may each be designed as flat, thin wall, thin pan vessels which materially increase the surface area available for heat transfer. In addition, this thin, flat configuration of the absorber and its thin walled (and therefore relatively flexible) construction permits substantial expansion and contraction of the absorber material during vaporization and absorption without generating voids which would interfere with heat transfer.

Greiner, Leonard (2853-A Hickory Pl., Costa Mesa, CA 92626)

1984-01-01T23:59:59.000Z

345

Chemical heat pump  

DOE Patents [OSTI]

A chemical heat pump system is disclosed for use in heating and cooling structures such as residences or commercial buildings. The system is particularly adapted to utilizing solar energy, but also increases the efficiency of other forms of thermal energy when solar energy is not available. When solar energy is not available for relatively short periods of time, the heat storage capacity of the chemical heat pump is utilized to heat the structure, as during nighttime hours. The design also permits home heating from solar energy when the sun is shining. The entire system may be conveniently rooftop located. In order to facilitate installation on existing structures, the absorber and vaporizer portions of the system may each be designed as flat, thin wall, thin pan vessels which materially increase the surface area available for heat transfer. In addition, this thin, flat configuration of the absorber and its thin walled (and therefore relatively flexible) construction permits substantial expansion and contraction of the absorber material during vaporization and absorption without generating voids which would interfere with heat transfer.

Greiner, Leonard (2853-A Hickory Pl., Costa Mesa, CA 92626)

1984-01-01T23:59:59.000Z

346

Chemical heat pump  

DOE Patents [OSTI]

A chemical heat pump system is disclosed for use in heating and cooling structures such as residences or commercial buildings. The system is particularly adapted to utilizing solar energy, but also increases the efficiency of other forms of thermal energy when solar energy is not available. When solar energy is not available for relatively short periods of time, the heat storage capacity of the chemical heat pump is utilized to heat the structure, as during nighttime hours. The design also permits home heating from solar energy when the sun is shining. The entire system may be conveniently rooftop located. In order to faciliate installation on existing structures, the absorber and vaporizer portions of the system may each be designed as flat, thin wall, thin pan vessels which materially increase the surface area available for heat transfer. In addition, this thin, flat configuration of the absorber and its thin walled (and therefore relatively flexible) construction permits substantial expansion and contraction of the absorber material during vaporization and absorption without generating voids which would interfere with heat transfer.

Greiner, Leonard (2853-A Hickory Pl., Costa Mesa, CA 92626)

1984-01-01T23:59:59.000Z

347

Microchannel heat sink assembly  

DOE Patents [OSTI]

The present invention provides a microchannel heat sink with a thermal range from cryogenic temperatures to several hundred degrees centigrade. The heat sink can be used with a variety of fluids, such as cryogenic or corrosive fluids, and can be operated at a high pressure. The heat sink comprises a microchannel layer preferably formed of silicon, and a manifold layer preferably formed of glass. The manifold layer comprises an inlet groove and outlet groove which define an inlet manifold and an outlet manifold. The inlet manifold delivers coolant to the inlet section of the microchannels, and the outlet manifold receives coolant from the outlet section of the microchannels. In one embodiment, the manifold layer comprises an inlet hole extending through the manifold layer to the inlet manifold, and an outlet hole extending through the manifold layer to the outlet manifold. Coolant is supplied to the heat sink through a conduit assembly connected to the heat sink. A resilient seal, such as a gasket or an O-ring, is disposed between the conduit and the hole in the heat sink in order to provide a watertight seal. In other embodiments, the conduit assembly may comprise a metal tube which is connected to the heat sink by a soft solder. In still other embodiments, the heat sink may comprise inlet and outlet nipples. The present invention has application in supercomputers, integrated circuits and other electronic devices, and is suitable for cooling materials to superconducting temperatures. 13 figs.

Bonde, W.L.; Contolini, R.J.

1992-03-24T23:59:59.000Z

348

Enhancing the energy efficiency of radio base stations   

E-Print Network [OSTI]

This thesis is concerned with the energy efficiency of cellular networks. It studies the dominant power consumer in future cellular networks, the Long Term Evolution (LTE) radio Base Station (BS), and proposes mechanisms ...

Holtkamp, Hauke Andreas

2014-06-30T23:59:59.000Z

349

Waiting for TOD : developing in the Millbrae BART Station Area  

E-Print Network [OSTI]

The suburban terminus station dedicates large amounts of land for parking in order to cater to its driving riders, and causes a trade-off tension between attracting ridership through providing park-and-rides and building ...

Shih, Janet Wei

2012-01-01T23:59:59.000Z

350

College Station Utilities- Residential Energy Back II Rebate Program  

Broader source: Energy.gov [DOE]

College Station Utilities offers an incentive for residential customers to install energy efficient HVAC equipment through the Energy Back II Program. To qualify for the rebate, the A/C system...

351

antarctic station casey: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

SOAP for setting up the tetheredsonde All of the Costa Rica REU groups for data 148 OF CAR SHARING STATIONS CiteSeer Summary: Approximately half of the worlds population is...

352

Strategy for international cooperation in planning the Chinese Space Station  

E-Print Network [OSTI]

After ten years of planning and pre-development, the Chinese government approved the space station project on September 25, 2010. In October 2010, the People's Republic of China (PRC) officially announced its independent ...

Foley, Jordan J. (Jordan James)

2014-01-01T23:59:59.000Z

353

Microsoft Word - Noxon Radio Station Upgrade CX.doc  

Broader source: Energy.gov (indexed) [DOE]

Action: Noxon Radio Station Upgrade Project Budget Information: Work Order 00254987 Task 03 Categorical Exclusion Applied (from Subpart D, 10 C.F.R. Part 1021: B1.7...

354

Where the Rubber Meets the Road -- the Alternative Fuel Station...  

Broader source: Energy.gov (indexed) [DOE]

Road -- the Alternative Fuel Station Locator August 10, 2010 - 2:32pm Addthis Dennis A. Smith Director, National Clean Cities Last week, this blog highlighted the highly efficient...

355

Niwot Ridge CRN Station Up & On-Line.  

E-Print Network [OSTI]

Niwot Ridge CRN Station Up & On-Line. I made a decision after the Science Panel Review to put tree removal Wind Speed 3, terrain elevation change Solar Radiation 3, solar shading to west #12;

356

0 1 2 3 4 5 Fig. S1. Core photograph combined with Ca, Mn, Fe counts and Mn/Fe ratio determined by XRF core  

E-Print Network [OSTI]

1. Core photograph combined with Ca, Mn, Fe counts and Mn/Fe ratio determined by XRF core scanning determined by XRF core scanning on core ZH10-19 from Lake Zurich recovered in 135 m water depth (2 m above counts and Mn/Fe ratio determined by XRF core scanning on core ZH10-21 from Lake Zurich recovered in 123

Gilli, Adrian

357

Southwest Region Experiment Station - Final Technical Report  

SciTech Connect (OSTI)

Southwest Technology Development Institute (SWTDI), an independent, university-based research institute, has been the operator of the Southwest Region Photovoltaic Experiment Station (SWRES) for almost 30 years. The overarching mission of SWTDI is to position PV systems and solar technologies to become cost-effective, major sources of energy for the United States. Embedded in SWTDI's general mission has been the more-focused mission of the SWRES: to provide value added technical support to the DOE Solar Energy Technologies Program (SETP) to effectively and efficiently meet the R&D needs and targets specified in the SETP Multi-Year Technical Plan. : The DOE/SETP goals of growing U.S. PV manufacturing into giga-watt capacities and seeing tera-watt-hours of solar energy production in the U.S. require an infrastructure that is under development. The staff of the SWRES has supported DOE/SETP through a coherent, integrated program to address infrastructural needs inhibiting wide-scale PV deployment in three major technical categories: specialized engineering services, workforce development, and deployment facilitation. The SWRES contract underwent three major revisions during its five year period-of- performance, but all tasks and deliverables fell within the following task areas: Task 1: PV Systems Assistance Center 1. Develop a Comprehensive multi-year plan 2. Provide technical workforce development materials and workshops for PV stakeholder groups including university, professional installers, inspectors, state energy offices, Federal agencies 3. Serve on the NABCEP exam committee 4. Provide on-demand technical PV system design reviews for U.S. PV stakeholders 5. Provide PV system field testing and instrumentation, technical outreach (including extensive support for the DOE Market Transformation program) Task 2: Design-for-Manufacture PV Systems 1. Develop and install 18 kW parking carport (cost share) and PV-thermal carport (Albuquerque) deriving and publishing lessons learned Task 3: PV Codes and Standards 1. Serve as the national lead for development and preparation of all proposals (related to PV) to the National Electrical Code 2. Participate in the Standards Technical Panels for modules (UL1703) and inverters (UL1741) Task 4: Assess Inverter Long Term Reliability 1. Install and monitor identical inverters at SWRES and SERES 2. Operate and monitor all inverters for 5 years, characterizing all failures and performance trends Task 5: Test and Evaluation Support for Solar America Initiative 1. Provide test and evaluation services to the National Laboratories for stage gate and progress measurements of SAI TPP winners

Rosenthal, A

2011-08-19T23:59:59.000Z

358

Solar heating system  

DOE Patents [OSTI]

An improved solar heating system in which the incident radiation of the sun is absorbed on collector panels, transferred to a storage unit and then distributed as heat for a building and the like. The improvement is obtained by utilizing a storage unit comprising separate compartments containing an array of materials having different melting points ranging from 75.degree. to 180.degree. F. The materials in the storage system are melted in accordance with the amount of heat absorbed from the sun and then transferred to the storage system. An efficient low volume storage system is provided by utilizing the latent heat of fusion of the materials as they change states in storing and releasing heat for distribution.

Schreyer, James M. (Oak Ridge, TN); Dorsey, George F. (Concord, TN)

1982-01-01T23:59:59.000Z

359

Improved solar heating systems  

DOE Patents [OSTI]

An improved solar heating system is described in which the incident radiation of the sun is absorbed on collector panels, transferred to a storage unit and then distributed as heat for a building and the like. The improvement is obtained by utilizing a storage unit comprising separate compartments containing an array of materials having different melting points ranging from 75 to 180/sup 0/F. The materials in the storage system are melted in accordance with the amount of heat absorbed from the sun and then transferred to the storage system. An efficient low volume storage system is provided by utilizing the latent heat of fusion of the materials as they change states in storing ad releasing heat for distribution.

Schreyer, J.M.; Dorsey, G.F.

1980-05-16T23:59:59.000Z

360

Large Optic Drying Station: Summary of Dryer Certification Tests  

SciTech Connect (OSTI)

The purpose of this document is to outline the methodology used to baseline and maintain the cleanliness status of the newly built and installed Large Optic Cleaning Station (LOCS). The station has currently been in use for eleven months; and after many cleaning studies and implementation of resulting improvements appears to be cleaning optics to a level that is acceptable for the fabrication of Nano-Laminates.

Barbee, T W; Ayers, S L; Ayers, M J

2009-08-28T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Bending properties of epoxy resin matrix composites filled with NiMnGa ferromagnetic shape memory alloy powders  

E-Print Network [OSTI]

Bending properties of epoxy resin matrix composites filled with Ni­Mn­Ga ferromagnetic shape memory­Mn­Ga Composite materials Mechanical properties Microstructure Two types of epoxy resin matrix composites filled­Mn­Ga epoxy resin composites were reported, yet the bending property of Ni­Mn­Ga-polymer smart composites has

Zheng, Yufeng

362

PHYSICAL REVIEW B 84, 205305 (2011) Spin-phonon coupling in single Mn-doped CdTe quantum dot  

E-Print Network [OSTI]

PHYSICAL REVIEW B 84, 205305 (2011) Spin-phonon coupling in single Mn-doped CdTe quantum dot C. L dynamics of a single Mn atom in a laser driven CdTe quantum dot is addressed theoretically. Recent of single Mn-doped CdTe dots, information about the quantum spin state of a single Mn atom is extracted from

Paris-Sud XI, Université de

363

Heat-Of-Reaction Chemical Heat Pumps--Possible Configurations  

E-Print Network [OSTI]

-807. (5) K. Kesavan. The Use of Dissociating Gases As the Working Fluid in Thermodynamic Power Conversion Cycles, Ph.D. thesis. Carnegie-Mellon University, 1978, Ann Arbor, MI: University Microfilms International, 1978. 5. Heat amplifier with a gas...ABSTRACT Chemical heat pumps utilize working fluids which undergo reversible chemical changes. Mechanically driven reactive heat pump cycles or, alternatively, hl~a: driven heat pumps in which either heat engine or heat pump working fluid...

Kirol, L. D.

364

Integrating preconcentrator heat controller  

DOE Patents [OSTI]

A method and apparatus for controlling the electric resistance heating of a metallic chemical preconcentrator screen, for example, used in portable trace explosives detectors. The length of the heating time-period is automatically adjusted to compensate for any changes in the voltage driving the heating current across the screen, for example, due to gradual discharge or aging of a battery. The total deposited energy in the screen is proportional to the integral over time of the square of the voltage drop across the screen. Since the net temperature rise, .DELTA.T.sub.s, of the screen, from beginning to end of the heating pulse, is proportional to the total amount of heat energy deposited in the screen during the heating pulse, then this integral can be calculated in real-time and used to terminate the heating current when a pre-set target value has been reached; thereby providing a consistent and reliable screen temperature rise, .DELTA.T.sub.s, from pulse-to-pulse.

Bouchier, Francis A. (Albuquerque, NM); Arakaki, Lester H. (Edgewood, NM); Varley, Eric S. (Albuquerque, NM)

2007-10-16T23:59:59.000Z

365

Proceedings: Heat exchanger workshop  

SciTech Connect (OSTI)

Heat transfer processes are of controlling importance in the operation of a thermal power plant. Heat exchangers are major cost items and are an important source of problems causing poor power plant availability and performance. A workshop to examine the improvements that can be made to heat exchangers was sponsored by the Electric Power Research Institute (EPRI) on June 10-11, 1986, in Palo Alto, California. This workshop was attended by 25 engineers and scientists representing EPRI-member utilities and EPRI consultants. A forum was provided for discussions related to the design, operation and maintenance of utility heat transfer equipment. The specific objectives were to identify research directions that could significantly improve heat exchanger performance, reliability and life cycle economics. Since there is a great diversity of utility heat transfer equipment in use, this workshop addressed two equipment categories: Boiler Feedwater Heaters (FWH) and Heat Recovery Steam Generators (HRSG). The workshop was divided into the following panel sessions: functional design, mechanical design, operation, suggested research topics, and prioritization. Each panel session began with short presentations by experts on the subject and followed by discussions by the attendees. This report documents the proceedings of the workshop and contains recommendations of potentially valuable areas of research and development. 4 figs.

Not Available

1987-07-01T23:59:59.000Z

366

Micro heat barrier  

DOE Patents [OSTI]

A highly effective, micron-scale micro heat barrier structure and process for manufacturing a micro heat barrier based on semiconductor and/or MEMS fabrication techniques. The micro heat barrier has an array of non-metallic, freestanding microsupports with a height less than 100 microns, attached to a substrate. An infrared reflective membrane (e.g., 1 micron gold) can be supported by the array of microsupports to provide radiation shielding. The micro heat barrier can be evacuated to eliminate gas phase heat conduction and convection. Semi-isotropic, reactive ion plasma etching can be used to create a microspike having a cusp-like shape with a sharp, pointed tip (<0.1 micron), to minimize the tip's contact area. A heat source can be placed directly on the microspikes. The micro heat barrier can have an apparent thermal conductivity in the range of 10.sup.-6 to 10.sup.-7 W/m-K. Multiple layers of reflective membranes can be used to increase thermal resistance.

Marshall, Albert C.; Kravitz, Stanley H.; Tigges, Chris P.; Vawter, Gregory A.

2003-08-12T23:59:59.000Z

367

Plutonium Oxidation and Subsequent Reduction by Mn (IV) Minerals  

SciTech Connect (OSTI)

Plutonium sorbed to rock tuff was preferentially associated with manganese oxides. On tuff and synthetic pyrolusite (Mn{sup IV}O{sub 2}), Pu(IV) or Pu(V) was initially oxidized, but over time Pu(IV) became the predominant oxidation state of sorbed Pu. Reduction of Pu(V/VI), even on non-oxidizing surfaces, is proposed to result from a lower Gibbs free energy of the hydrolyzed Pu(IV) surface species versus that of the Pu(V) or Pu(VI) surface species. This work suggests that despite initial oxidation of sorbed Pu by oxidizing surfaces to more soluble forms, the less mobile form of Pu, Pu(IV), will dominate Pu solid phase speciation during long term geologic storage. The safe design of a radioactive waste or spent nuclear fuel geologic repository requires a risk assessment of radionuclides that may potentially be released into the surrounding environment. Geochemical knowledge of the radionuclide and the surrounding environment is required for predicting subsurface fate and transport. Although difficult even in simple systems, this task grows increasingly complicated for constituents, like Pu, that exhibit complex environmental chemistries. The environmental behavior of Pu can be influenced by complexation, precipitation, adsorption, colloid formation, and oxidation/reduction (redox) reactions (1-3). To predict the environmental mobility of Pu, the most important of these factors is Pu oxidation state. This is because Pu(IV) is generally 2 to 3 orders of magnitude less mobile than Pu(V) in most environments (4). Further complicating matters, Pu commonly exists simultaneously in several oxidation states (5, 6). Choppin (7) reported Pu may exist as Pu(IV), Pu(V), or Pu(VI) oxic natural groundwaters. It is generally accepted that plutonium associated with suspended particulate matter is predominantly Pu(IV) (8-10), whereas Pu in the aqueous phase is predominantly Pu(V) (2, 11-13). The influence of the character of Mn-containing minerals expected to be found in subsurface repository environments on Pu oxidation state distributions has been the subject of much recent research. Kenney-Kennicutt and Morse (14), Duff et al. (15), and Morgenstern and Choppin (16) observed oxidation of Pu facilitated by Mn(IV)-bearing minerals. Conversely, Shaughnessy et al. (17) used X-ray Absorption near-edge spectroscopy (XANES) to show reduction of Pu(VI) by hausmannite (Mn{sup II}Mn{sub 2}{sup III}O{sub 4}) and manganite ({gamma}-Mn{sup III}OOH) and Kersting et al., (18) observed reduction of Pu(VI) by pyrolusite (Mn{sup IV}O{sub 2}). In this paper, we attempt to reconcile the apparently conflicting datasets by showing that Mn-bearing minerals can indeed oxidize Pu, however, if the oxidized species remains on the solid phase, the oxidation step competes with the formation of Pu(IV) that becomes the predominant solid phase Pu species with time. The experimental approach we took was to conduct longer term (approximately two years later) oxidation state analyses on the Pu sorbed to Yucca Mountain tuff (initial analysis reported by Duff et al., (15)) and measure the time-dependant changes in the oxidation state distribution of Pu in the presence of the Mn mineral pyrolusite.

KAPLAN, DANIEL

2005-09-13T23:59:59.000Z

368

Condensing Heating and Water Heating Equipment Workshop Location...  

Energy Savers [EERE]

Condensing Heating and Water Heating Equipment Workshop Location: Washington Gas Light Appliance Training Facility 6801 Industrial Road Springfield, VA Date: October 9, 2014 Time:...

369

City of Klamath Falls District Heating District Heating Low Temperatur...  

Open Energy Info (EERE)

Geothermal Facility Jump to: navigation, search Name City of Klamath Falls District Heating District Heating Low Temperature Geothermal Facility Facility City of Klamath...

370

Economic Options for Upgrading Waste Heat  

E-Print Network [OSTI]

There are at least six major types of equipment that upgrade waste heat: (1) thermocompressor; (2) electric drive compressor heat pump; (3) absorption heat pump; (4) high temperature heat powered compressor heat pump; (5) reverse absorption heat...

Erickson, D. C.

1983-01-01T23:59:59.000Z

371

Molecular heat pump  

E-Print Network [OSTI]

We propose a novel molecular device that pumps heat against a thermal gradient. The system consists of a molecular element connecting two thermal reservoirs that are characterized by different spectral properties. The pumping action is achieved by applying an external force that periodically modulates molecular levels. This modulation affects periodic oscillations of the internal temperature of the molecule and the strength of its coupling to each reservoir resulting in a net heat flow in the desired direction. The heat flow is examined in the slow and fast modulation limits and for different modulation waveforms, thus making it possible to optimize the device performance.

Dvira Segal; Abraham Nitzan

2005-10-11T23:59:59.000Z

372

Heat treatment furnace  

DOE Patents [OSTI]

A furnace heats through both infrared radiation and convective air utilizing an infrared/purge gas design that enables improved temperature control to enable more uniform treatment of workpieces. The furnace utilizes lamps, the electrical end connections of which are located in an enclosure outside the furnace chamber, with the lamps extending into the furnace chamber through openings in the wall of the chamber. The enclosure is purged with gas, which gas flows from the enclosure into the furnace chamber via the openings in the wall of the chamber so that the gas flows above and around the lamps and is heated to form a convective mechanism in heating parts.

Seals, Roland D; Parrott, Jeffrey G; DeMint, Paul D; Finney, Kevin R; Blue, Charles T

2014-10-21T23:59:59.000Z

373

Heat storage with CREDA  

SciTech Connect (OSTI)

The principle of operation of ETS or Electric Thermal Storage is discussed in this book. As can be seen by the diagram presented, heating elements buried deep within the core are energized during off-peak periods or periods of lower cost energy. These elements charge the core to a per-determined level, then during the on-peak periods when the cost of electricity is higher or demand is higher, the heat is extracted from the core. The author discusses how this technology has progressed to the ETS equipment of today; this being the finer control of charging rates and extraction of heat from the core.

Beal, T. (Fostoria Industries, Fostoria, OH (US))

1987-01-01T23:59:59.000Z

374

Heat pumps and under floor heating as a heating system for Finnish low-rise residential buildings.  

E-Print Network [OSTI]

??In bachelor’s thesis the study of under floor heating system with ground source heat pump for the heat transfers fluid heating is considered. The case… (more)

Chuduk, Svetlana

2010-01-01T23:59:59.000Z

375

Promotion of efficient heat pumps for heating (ProHeatPump)  

E-Print Network [OSTI]

Project Promotion of efficient heat pumps for heating (ProHeatPump) EIE/06/072 / S12.444283 Supplementary report: Heat pumps in Norway May 2009 Work Package 4: Policy context and measures Authors: Nils of the industry and markets in the ProHeatPump partner countries, and should provide useful comparisons

376

Photovoltaic roof heat flux  

E-Print Network [OSTI]

under the offset unit's solar panel, the hf formula (16) wasdrop below the angle unit's solar panel at night time. D u rfor both the units, the solar panel covered roof was a heat

Samady, Mezhgan Frishta

2011-01-01T23:59:59.000Z

377

Composite heat damage assessment  

SciTech Connect (OSTI)

The effects of heat damage were determined on the residual mechanical, physical, and chemical properties of IM6/3501-6 laminates, and potential nondestructive techniques to detect and assess material heat damage were evaluated. About one thousand preconditioned specimens were exposed to elevated temperatures, then cooled to room temperature and tested in compression, flexure, interlaminar shear, shore-D hardness, weight loss, and change in thickness. Specimens experienced significant and irreversible reduction in their residual properties when exposed to temperatures exceeding the material upper service temperature of this material (350{degrees}F). The Diffuse Reflectance Infrared Fourier Transform and Laser-Pumped Fluorescence techniques were found to be capable of rapid, in-service, nondestructive detection and quantitation of heat damage in IM6/3501- 6. These techniques also have the potential applicability to detect and assess heat damage effects in other polymer matrix composites.

Janke, C.J.; Wachter, E.A. [Oak Ridge National Lab., TN (United States); Philpot, H.E. [Oak Ridge K-25 Site, TN (United States); Powell, G.L. [Oak Ridge Y-12 Plant, TN (United States)

1993-12-31T23:59:59.000Z

378

Solar Heating Contractor Licensing  

Broader source: Energy.gov [DOE]

Michigan offers a solar heating contractor specialty license to individuals who have at least three years of experience installing solar equipment under the direction of a licensed solar contractor...

379

Passive solar heating analysis  

SciTech Connect (OSTI)

This book discusses about the design of solar heating systems. The terms and symbols are clearly defined. Step-by-step procedures are indicated. Worked examples are given with tables, graphs, appendixes.

Balcomb, J.D.; Jones, R.W.; Mc Farland, R.D.; Wray, W.O.

1984-01-01T23:59:59.000Z

380

Wood Heating Fuel Exemption  

Broader source: Energy.gov [DOE]

This statute exempts from the state sales tax all wood or "refuse-derived" fuel used for heating purposes. The law does not make any distinctions about whether the qualified fuels are used for...

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Heat Waves, Global Warming, and Mitigation  

E-Print Network [OSTI]

Heat Waves, Global Warming, and Mitigation Ann E. Carlson*II. HEAT WAVE DEFINITIONS .. A . HCHANGE AND HEAT WAVES .. CLIMATE III. IV. HEAT

Carlson, Ann E.

2008-01-01T23:59:59.000Z

382

Heat flux limiting sleeves  

DOE Patents [OSTI]

A heat limiting tubular sleeve extending over only a portion of a tube having a generally uniform outside diameter, the sleeve being open on both ends, having one end thereof larger in diameter than the other end thereof and having a wall thickness which decreases in the same direction as the diameter of the sleeve decreases so that the heat transfer through the sleeve and tube is less adjacent the large diameter end of the sleeve than adjacent the other end thereof.

Harris, William G. (Tampa, FL)

1985-01-01T23:59:59.000Z

383

NGNP Process Heat Utilization: Liquid Metal Phase Change Heat Exchanger  

SciTech Connect (OSTI)

One key long-standing issue that must be overcome to fully realize the successful growth of nuclear power is to determine other benefits of nuclear energy apart from meeting the electricity demands. The Next Generation Nuclear Plant (NGNP) will most likely be producing electricity and heat for the production of hydrogen and/or oil retrieval from oil sands and oil shale to help in our national pursuit of energy independence. For nuclear process heat to be utilized, intermediate heat exchange is required to transfer heat from the NGNP to the hydrogen plant or oil recovery field in the most efficient way possible. Development of nuclear reactor - process heat technology has intensified the interest in liquid metals as heat transfer media because of their ideal transport properties. Liquid metal heat exchangers are not new in practical applications. An important rational for considering liquid metals is the potential convective heat transfer is among the highest known. Thus explains the interest in liquid metals as coolant for intermediate heat exchange from NGNP. For process heat it is desired that, intermediate heat exchangers (IHX) transfer heat from the NGNP in the most efficient way possible. The production of electric power at higher efficiency via the Brayton Cycle, and hydrogen production, requires both heat at higher temperatures and high effectiveness compact heat exchangers to transfer heat to either the power or process cycle. Compact heat exchangers maximize the heat transfer surface area per volume of heat exchanger; this has the benefit of reducing heat exchanger size and heat losses. High temperature IHX design requirements are governed in part by the allowable temperature drop between the outlet and inlet of the NGNP. In order to improve the characteristics of heat transfer, liquid metal phase change heat exchangers may be more effective and efficient. This paper explores the overall heat transfer characteristics and pressure drop of the phase change heat exchanger with Na as the heat exchanger coolant. In order to design a very efficient and effective heat exchanger one must optimize the design such that we have a high heat transfer and a lower pressure drop, but there is always a trade-off between them. Based on NGNP operational parameters, a heat exchanger analysis with the sodium phase change will be presented to show that the heat exchanger has the potential for highly effective heat transfer, within a small volume at reasonable cost.

Piyush Sabharwall; Mike Patterson; Vivek Utgikar; Fred Gunnerson

2008-09-01T23:59:59.000Z

384

ARM: Broadband Radiometer Station (BRS) broadband shortwave and longwave 1-min radiation data with Dutton correction  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

Broadband Radiometer Station (BRS) broadband shortwave and longwave 1-min radiation data with Dutton correction

Stoffel, Tom; Kay, Bev; Habte, Aron; Anderberg, Mary; Kutchenreiter, Mark

385

Intrinsically irreversible heat engine  

DOE Patents [OSTI]

A class of heat engines based on an intrinsically irreversible heat transfer process is disclosed. In a typical embodiment the engine comprises a compressible fluid that is cyclically compressed and expanded while at the same time being driven in reciprocal motion by a positive displacement drive means. A second thermodynamic medium is maintained in imperfect thermal contact with the fluid and bears a broken thermodynamic symmetry with respect to the fluid. The second thermodynamic medium is a structure adapted to have a low fluid flow impedance with respect to the compressible fluid, and which is further adapted to be in only moderate thermal contact with the fluid. In operation, thermal energy is pumped along the second medium due to a phase lag between the cyclical heating and cooling of the fluid and the resulting heat conduction between the fluid and the medium. In a preferred embodiment the engine comprises an acoustical drive and a housing containing a gas which is driven at a resonant frequency so as to be maintained in a standing wave. Operation of the engine at acoustic frequencies improves the power density and coefficient of performance. The second thermodynamic medium can be coupled to suitable heat exchangers to utilize the engine as a simple refrigeration device having no mechanical moving parts. Alternatively, the engine is reversible in function so as to be utilizable as a prime mover by coupling it to suitable sources and sinks of heat. 11 figs.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1984-12-25T23:59:59.000Z

386

Radial flow heat exchanger  

DOE Patents [OSTI]

A radial flow heat exchanger (20) having a plurality of first passages (24) for transporting a first fluid (25) and a plurality of second passages (26) for transporting a second fluid (27). The first and second passages are arranged in stacked, alternating relationship, are separated from one another by relatively thin plates (30) and (32), and surround a central axis (22). The thickness of the first and second passages are selected so that the first and second fluids, respectively, are transported with laminar flow through the passages. To enhance thermal energy transfer between first and second passages, the latter are arranged so each first passage is in thermal communication with an associated second passage along substantially its entire length, and vice versa with respect to the second passages. The heat exchangers may be stacked to achieve a modular heat exchange assembly (300). Certain heat exchangers in the assembly may be designed slightly differently than other heat exchangers to address changes in fluid properties during transport through the heat exchanger, so as to enhance overall thermal effectiveness of the assembly.

Valenzuela, Javier (Hanover, NH)

2001-01-01T23:59:59.000Z

387

Intrinsically irreversible heat engine  

DOE Patents [OSTI]

A class of heat engines based on an intrinsically irreversible heat transfer process is disclosed. In a typical embodiment the engine comprises a compressible fluid that is cyclically compressed and expanded while at the same time being driven in reciprocal motion by a positive displacement drive means. A second thermodynamic medium is maintained in imperfect thermal contact with the fluid and bears a broken thermodynamic symmetry with respect to the fluid. the second thermodynamic medium is a structure adapted to have a low fluid flow impedance with respect to the compressible fluid, and which is further adapted to be in only moderate thermal contact with the fluid. In operation, thermal energy is pumped along the second medium due to a phase lag between the cyclical heating and cooling of the fluid and the resulting heat conduction between the fluid and the medium. In a preferred embodiment the engine comprises an acoustical drive and a housing containing a gas which is driven at a resonant frequency so as to be maintained in a standing wave. Operation of the engine at acoustic frequencies improves the power density and coefficient of performance. The second thermodynamic medium can be coupled to suitable heat exchangers to utilize the engine as a simple refrigeration device having no mechanical moving parts. Alternatively, the engine is reversible in function so as to be utilizable as a prime mover by coupling it to suitable sources and sinks of heat.

Wheatley, John C. (Los Alamos, NM); Swift, Gregory W. (Los Alamos, NM); Migliori, Albert (Santa Fe, NM)

1984-01-01T23:59:59.000Z

388

Convective heat flow probe  

DOE Patents [OSTI]

A convective heat flow probe device is provided which measures heat flow and fluid flow magnitude in the formation surrounding a borehole. The probe comprises an elongate housing adapted to be lowered down into the borehole; a plurality of heaters extending along the probe for heating the formation surrounding the borehole; a plurality of temperature sensors arranged around the periphery of the probe for measuring the temperature of the surrounding formation after heating thereof by the heater elements. The temperature sensors and heater elements are mounted in a plurality of separate heater pads which are supported by the housing and which are adapted to be radially expanded into firm engagement with the walls of the borehole. The heat supplied by the heater elements and the temperatures measured by the temperature sensors are monitored and used in providing the desired measurements. The outer peripheral surfaces of the heater pads are configured as segments of a cylinder and form a full cylinder when taken together. A plurality of temperature sensors are located on each pad so as to extend along the length and across the width thereof, with a heating element being located in each pad beneath the temperature sensors. An expansion mechanism driven by a clamping motor provides expansion and retraction of the heater pads and expandable packet-type seals are provided along the probe above and below the heater pads.

Dunn, J.C.; Hardee, H.C.; Striker, R.P.

1984-01-09T23:59:59.000Z

389

Intrinsically irreversible heat engine  

DOE Patents [OSTI]

A class of heat engines based on an intrinsically irreversible heat transfer process is disclosed. In a typical embodiment the engine comprises a compressible fluid that is cyclically compressed and expanded while at the same time being driven in reciprocal motion by a positive displacement drive means. A second thermodynamic medium is maintained in imperfect thermal contact with the fluid and bears a broken thermodynamic symmetry with respect to the fluid. The second thermodynamic medium is a structure adapted to have a low fluid flow impedance with respect to the compressible fluid, and which is further adapted to be in only moderate thermal contact with the fluid. In operation, thermal energy is pumped along the second medium due to a phase lag between the cyclical heating and cooling of the fluid and the resulting heat conduction between the fluid and the medium. In a preferred embodiment the engine comprises an acoustical drive and a housing containing a gas which is driven at a resonant frequency so as to be maintained in a standing wave. Operation of the engine at acoustic frequencies improves the power density and coefficient of performance. The second thermodynamic medium can be coupled to suitable heat exchangers to utilize the engine as a simple refrigeration device having no mechanical moving parts. Alternatively, the engine is reversible in function so as to be utilizable as a prime mover by coupling it to suitable sources and sinks of heat.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1984-01-01T23:59:59.000Z

390

Charge transport properties of CdMnTe radiation detectors  

SciTech Connect (OSTI)

Growth, fabrication and characterization of indium-doped cadmium manganese telluride (CdMnTe)radiation detectors have been described. Alpha-particle spectroscopy measurements and time resolved current transient measurements have yielded an average charge collection efficiency approaching 100 %. Spatially resolved charge collection efficiency maps have been produced for a range of detector bias voltages. Inhomogeneities in the charge transport of the CdMnTe crystals have been associated with chains of tellurium inclusions within the detector bulk. Further, it has been shown that the role of tellurium inclusions in degrading chargecollection is reduced with increasing values of bias voltage. The electron transit time was determined from time of flight measurements. From the dependence of drift velocity on applied electric field the electron mobility was found to be n = (718 55) cm2/Vs at room temperature.

Kim K.; Rafiel, R.; Boardman, M.; Reinhard, I.; Sarbutt, A.; Watt, G.; Watt, C.; Uxa, S.; Prokopovich, D.A.; Belas, E.; Bolotnikov, A.E.; James, R.B.

2012-04-11T23:59:59.000Z

391

High-Resolution Mn EXAFS of the Oxygen-Evolving Complex inPhotosystem II: Structural Implications for the Mn4Ca Cluster  

SciTech Connect (OSTI)

The biological generation of oxygen by the oxygen-evolving complex in photosystem II (PS II) is one of natures most important reactions. The recent X-ray crystal structures, while limited by resolutions of 3.2 to 3.5 A, have located the electron density associated with the Mn4Ca complex within the multi-protein PS II complex. Detailed structures critically depend on input from spectroscopic techniques such as EXAFS and EPR/ENDOR, as the XRD resolution does not allow for accurate determination of the position of Mn/Ca or the bridging and terminal ligand atoms. The number and distances of Mn-Mn/Ca/ligand interactions determined from EXAFS provide important constraints for the structure of the Mn cluster. Here we present data from a high-resolution EXAFS method using a novel multi-crystal monochromator that show three short Mn-Mn distances between 2.7 and 2.8 A and hence the presence of three di-mu-oxobridged units in the Mn4Ca cluster. This result imposes clear limitations on the proposed structures based on spectroscopic and diffraction data and provides input for refining such structures.

Yano, Junko; Pushkar, Yulia; Glatzel, Pieter; Lewis, Azul; Sauer,Kenneth; Messinger, Johannes; Bergmann, Uwe; Yachandra, Vittal

2005-09-06T23:59:59.000Z

392

Ferromagnetic Mn moments at SrRuO3/SrMnO3 interfaces Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439  

E-Print Network [OSTI]

Ferromagnetic Mn moments at SrRuO3/SrMnO3 interfaces Y. Choia Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439 Y. Z. Yoo, O. Chmaissem, A. Ullah, S. Kolesnik, and C. W University, DeKalb, Illinois 60115 D. Haskel Advanced Photon Source, Argonne National Laboratory, Argonne

Haskel, Daniel

393

Magnetic field-induced phase transformation and variant reorientation in Ni2MnGa and NiMnCoIn magnetic shape memory alloys  

E-Print Network [OSTI]

The purpose of this work is to reveal the governing mechanisms responsible for the magnetic field-induced i) martensite reorientation in Ni2MnGa single crystals, ii) stress-assisted phase transformation in Ni2MnGa single crystals and iii) phase...

Karaca, Haluk Ersin

2009-05-15T23:59:59.000Z

394

INVESTIGATION OF HYDRAULIC PROBLEMS IN PUMPING STATION; CASE STUDY  

E-Print Network [OSTI]

Pumping stations play an important role in agriculture development projects. Performance of the pumping stations should satisfy water requirements, and management. There are many problems face these pumping stations affecting their reliability and stability. Hydraulic problems are the most important item in the field of pumping station operation and design. Motivation of this research was presence of wear and pitting impellers and casing of double suction volute casing centrifugal pumps for Ahmed Orabee Pumping Station. Vibration level, hydraulic performance test and visual inspection of impeller wear and pitting show that cavitation problem is the cause of damage. Cavitation normally occurs when liquid at a constant temperature is subjected to vapor pressure either by static or dynamic means. If the local pressure somewhere in the fluid drops to or below vapor pressure and nuclei are present, vapor cavities can be formed. As long as the local pressure stays at vapor pressure and cavity has reached a critical diameter, it will continue to grow rapidly. If the surrounding pressure is above vapor pressure, the bubbles become unstable and collapse. The

M. A. Younes

395

DOPING AND BOND LENGTH CONTRIBUTIONS TO Mn K-EDGE SHIFT IN La1-xSrxMnO3 AND THEIR CORRELATION WITH ELECTRICAL TRANSPORT BEHAVIOUR.  

SciTech Connect (OSTI)

The experimental Mn K-edge x-ray absorption spectra of La{sub 1-x}Sr{sub x}MnO{sub 3}, x = 0 - 0.7 are compared with the band structure calculations using spin polarized density functional theory. It is explicitly shown that there is a correspondence between the inflection point on the absorption edge and the center of gravity of the unoccupied Mn 4p-band. This correspondence has been used to separate the doping and size contributions to edge shift due to variation in number of electrons in valence band and Mn-O bond lengths, respectively when Sr is doped into LaMnO{sub 3}. Such separation is helpful to find the localization behavior of charge carriers and to understand the observed transport properties and type of charge carrier participating in the conduction process in these compounds.

PANDEY,S.K.; KHALID,S.; BINDU, R.; KUMAR, A.; PIMPALE, A.V.

2006-12-04T23:59:59.000Z

396

Solar air heating system for combined DHW and space heating  

E-Print Network [OSTI]

Solar air heating system for combined DHW and space heating solar air collector PV-panel fannon-return valve DHW tank mantle cold waterhot water roof Solar Energy Centre Denmark Danish Technological Institute SEC-R-29 #12;Solar air heating system for combined DHW and space heating Søren �stergaard Jensen

397

Heat exchanger device and method for heat removal or transfer  

DOE Patents [OSTI]

Systems and methods for a forced-convection heat exchanger are provided. In one embodiment, heat is transferred to or from a thermal load in thermal contact with a heat conducting structure, across a narrow air gap, to a rotating heat transfer structure immersed in a surrounding medium such as air.

Koplow, Jeffrey P. (San Ramon, CA)

2012-07-24T23:59:59.000Z

398

Heat exchanger device and method for heat removal or transfer  

DOE Patents [OSTI]

Systems and methods for a forced-convection heat exchanger are provided. In one embodiment, heat is transferred to or from a thermal load in thermal contact with a heat conducting structure, across a narrow air gap, to a rotating heat transfer structure immersed in a surrounding medium such as air.

Koplow, Jeffrey P

2013-12-10T23:59:59.000Z

399

Locating PHEV Exchange Stations in V2G  

E-Print Network [OSTI]

Plug-in hybrid electric vehicles (PHEVs) are an environmentally friendly technology that is expected to rapidly penetrate the transportation system. Renewable energy sources such as wind and solar have received considerable attention as clean power options for future generation expansion. However, these sources are intermittent and increase the uncertainty in the ability to generate power. The deployment of PHEVs in a vehicle-to-grid (V2G) system provide a potential mechanism for reducing the variability of renewable energy sources. For example, PHEV supporting infrastructures like battery exchange stations that provide battery service to PHEV customers could be used as storage devices to stabilize the grid when renewable energy production is fluctuating. In this paper, we study how to best site these stations in terms of how they can support both the transportation system and the power grid. To model this problem we develop a two-stage stochastic program to optimally locate the stations prior to the realizat...

Pan, Feng; Berscheid, Alan; Izraelevitz, David

2010-01-01T23:59:59.000Z

400

Cranberry Station Farm and Grounds Manager (R35360) The University of Massachusetts Cranberry Station (www.umass.edu/cranberry) has a  

E-Print Network [OSTI]

Cranberry Station Farm and Grounds Manager (R35360) The University of Massachusetts Cranberry Station (www.umass.edu/cranberry) has a full time/fully benefited position available. Benefits include vacation, retirement, medical, and dental. Duties: Under the general supervision of the Cranberry Station

Mountziaris, T. J.

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Oil Extraction Factory Crude Oil Heating System Design  

E-Print Network [OSTI]

Abstract:-The design of general process is divided into: according to the original material and the data were based on the calculated; calculate the joint station dewatering tank and the sewage tank capacity; then its thermodynamic calculation, hydraulic calculation, selection of pump in heating furnace and to determine the types and quantity of the last of the pipelines; the permitted maximum, minimum throughput and stop lose time to carry out a series of process calculation, also made the hot oil pipeline thermal stress compensation calculation. Keywords:-calculate; hydraulic; pipeline;minimum throughput I.

Dai Qiushi; Pan Yi; Yang Shuangchun

402

Solar photovoltaic power system for a radio station  

SciTech Connect (OSTI)

Under sponsorship of the US Department of Energy, Massachusetts Institute of Technology Lincoln Laboratory has developed a concept for a small photovoltaic power system. Of simple construction, the system uses low-cost, prefabricated, transportable units for easy, fast installation and requires minimal site preparation. The first application of this experimental system began operation in August 1979 at daytime AM radio station WNBO in Bryan, Ohio. The project was jointly undertaken by the Laboratory and the radio station. The photovoltaic system described holds promise for a wide range of applications and economic feasibility by the mid- to late-1980s.

Nichols, B. E.

1980-12-01T23:59:59.000Z

403

Design of photovoltaic central power station concentrator array  

SciTech Connect (OSTI)

A design for a photovoltaic central power station using tracking concentrators has been developed. The 100 MW plant is assumed to be located adjacent to the Saguaro Power Station of Arizona Public Service. The design assumes an advanced Martin Marietta two-axis tracking fresnel lens concentrator. The concentrators are arrayed in 5 MW subfields, each with its own power conditioning unit. The photovoltaic plant output is connected to the existing 115 kV switchyard. The site specific design allows detailed cost estimates for engineering, site preparation, and installation. Collector and power conditioning costs have been treated parametrically.

Not Available

1984-02-01T23:59:59.000Z

404

EIS-0210: Tampa Electric Company-Polk Power Station (Adopted)  

Broader source: Energy.gov [DOE]

The U.S. Environmental Protection Agency prepared this statement to fulfill its National Environmental Policy Act requirements with respect to the potential issuance of a permit to the Tampa Electric Company under the National Pollutant Discharge Elimination System for the 1,150-MW Polk Power Station, a new pollutant source. The U.S. Department of Energy served as a cooperating agency in the development of this document due to its potential role to provide cost-shared financial assistance for a 260-MW Integrated Gasification Combined Cycle unit at the Power Station under its Clean Coal Technology Demonstration Project, and adopted the document by August 1994.

405

Sandia National Laboratories: Hydrogen Refueling Stations Analysis Model  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassive SolarEducationStation Technology Infrastructure ResearchRefueling Stations

406

Effect of a high electric field on the conductivity of MnGa{sub 2}S{sub 4}, MnIn{sub 2}S{sub 4}, and MnGaInS{sub 4} single crystals  

SciTech Connect (OSTI)

The results of studying the effect of a high electric field on the conductivity of MnGa{sub 2}S{sub 4}, MnIn{sub 2}S{sub 4}, and MnGaInS{sub 4} single crystals are reported. The activation energy is determined in high and low electric fields. It is established that the decrease in the activation energy with increasing the external voltage is associated with decreasing the depth of the potential well, in which the electron is located.

Niftiev, N. N. [Azerbaijan State Pedagogical University (Azerbaijan); Tagiev, O. B. [National Academy of Sciences of Azerbaijan, Institute of Physics (Azerbaijan)

2009-09-15T23:59:59.000Z

407

IV. -PHOTOMAGNETISM AND CONDUCT I W r PHOTOMAGNETIC EFFECT IN A Li-Mn FERRITE  

E-Print Network [OSTI]

IV. - PHOTOMAGNETISM AND CONDUCT I W r PHOTOMAGNETIC EFFECT IN A Li-Mn FERRITE P. BERNSTEIN and T'effet photomagnCtique dans le ferrite Fez,I oLi0.45Mn0.4504 au moyen de la variation de la perm investigated in a Fez.loLi0.45Mn0.4504ferrite by looking at the variations of the permeability under light

Paris-Sud XI, Université de

408

Electronic Structure and Oxidation State Changes in the Mn (4) Ca Cluster of Photosystem II  

SciTech Connect (OSTI)

Oxygen-evolving complex (Mn{sub 4}Ca cluster) of Photosystem II cycles through five intermediate states (S{sub i}-states, i = 0-4) before a molecule of dioxygen is released. During the S-state transitions, electrons are extracted from the OEC, either from Mn or alternatively from a Mn ligand. The oxidation state of Mn is widely accepted as Mn{sub 4}(III{sub 2},IV{sub 2}) and Mn{sub 4}(III,IV{sub 3}) for S{sub 1} and S{sub 2} states, while it is still controversial for the S{sub 0} and S{sub 3} states. We used resonant inelastic X-ray scattering (RIXS) to study the electronic structure of Mn{sub 4}Ca complex in the OEC. The RIXS data yield two-dimensional plots that provide a significant advantage by obtaining both K-edge pre-edge and L-edge-like spectra (metal spin state) simultaneously. We have collected data from PSII samples in the each of the S-states and compared them with data from various inorganic Mn complexes. The spectral changes in the Mn 1s2p{sub 3/2} RIXS spectra between the S-states were compared to those of the oxides of Mn and coordination complexes. The results indicate strong covalency for the electronic configuration in the OEC, and we conclude that the electron is transferred from a strongly delocalized orbital, compared to those in Mn oxides or coordination complexes. The magnitude for the S{sub 0} to S{sub 1}, and S{sub 1} to S{sub 2} transitions is twice as large as that during the S{sub 2} to S{sub 3} transition, indicating that the electron for this transition is extracted from a highly delocalized orbital with little change in charge density at the Mn atoms.

Yano, J.; Pushkar, Y.; Messinger, J.; Bergmann, U.; Glatzel, P.; Yachandra, V.K.; /SLAC

2012-08-17T23:59:59.000Z

409

Structural Changes in the Mn(4)Ca Cluster And the Mechanism of Photosynthetic Water Splitting  

SciTech Connect (OSTI)

Photosynthetic water oxidation, where water is oxidized to dioxygen, is a fundamental chemical reaction that sustains the biosphere. This reaction is catalyzed by a Mn{sub 4}Ca complex in the photosystem II (PS II) oxygen-evolving complex (OEC): a multiprotein assembly embedded in the thylakoid membranes of green plants, cyanobacteria, and algae. The mechanism of photosynthetic water oxidation by the Mn{sub 4}Ca cluster in photosystem II is the subject of much debate, although lacking structural characterization of the catalytic intermediates. Biosynthetically exchanged Ca/Sr-PS II preparations and x-ray spectroscopy, including extended x-ray absorption fine structure (EXAFS), allowed us to monitor Mn-Mn and Ca(Sr)-Mn distances in the four intermediate S states, S{sub 0} through S{sub 3}, of the catalytic cycle that couples the one-electron photochemistry occurring at the PS II reaction center with the four-electron water-oxidation chemistry taking place at the Mn{sub 4}Ca(Sr) cluster. We have detected significant changes in the structure of the complex, especially in the Mn-Mn and Ca(Sr)-Mn distances, on the S{sub 2}-to-S{sub 3} and S{sub 3}-to-S{sub 0} transitions. These results implicate the involvement of at least one common bridging oxygen atom between the Mn-Mn and Mn-Ca(Sr) atoms in the O-O bond formation. Because PS II cannot advance beyond the S{sub 2} state in preparations that lack Ca(Sr), these results show that Ca(Sr) is one of the critical components in the mechanism of the enzyme. The results also show that Ca is not just a spectator atom involved in providing a structural framework, but is actively involved in the mechanism of water oxidation and represents a rare example of a catalytically active Ca cofactor.

Pushkar, Y.; Yano, J.; Sauer, K.; Boussac, A.; Yachandra, V.K.

2009-05-21T23:59:59.000Z

410

Structural Changes in the Mn4Ca Cluster and the Mechanism of Photosynthetic Water Splitting  

SciTech Connect (OSTI)

Photosynthetic water oxidation, where water is oxidized to dioxygen, is a fundamental chemical reaction that sustains the biosphere. This reaction is catalyzed by a Mn4Ca complex in the photosystem II (PS II) oxygen-evolving complex (OEC): a multiproteinassembly embedded in the thylakoid membranes of green plants, cyanobacteria, and algae. The mechanism of photosynthetic water oxidation by the Mn4Ca cluster in photosystem II is the subject of much debate, although lacking structural characterization of the catalytic intermediates. Biosynthetically exchanged Ca/Sr-PS II preparations and x-ray spectroscopy, including extended x-ray absorption fine structure (EXAFS), allowed us to monitor Mn-Mn and Ca(Sr)-Mn distances in the four intermediate S states, S0 through S3, of the catalytic cycle that couples the one-electron photochemistry occurring at the PS II reaction center with the four-electron water-oxidation chemistry taking place at the Mn4Ca(Sr) cluster. We have detected significant changes in the structure of the complex, especially in the Mn-Mn and Ca(Sr)-Mn distances, on the S2-to-S3 and S3-to-S0 transitions. These results implicate the involvement of at least one common bridging oxygen atom between the Mn-Mn and Mn-Ca(Sr) atoms in the O-O bond formation. Because PS II cannot advance beyond the S2 state in preparations that lack Ca(Sr), these results show that Ca(Sr) is one of the critical components in the mechanism of the enzyme. The results also show that Ca is not just a spectator atom involved in providing a structural framework, but is actively involved in the mechanism of water oxidation and represents a rare example of a catalytically active Ca cofactor.

Pushkar, Y.; Yano, J.; Sauer, K.; Boussac, A.; Yachandra, V.K.

2007-10-25T23:59:59.000Z

411

Single Nanorod Devices for Battery Diagnostics: A Case Study on LiMn2O4  

E-Print Network [OSTI]

correlate well with the better cycling performance of Al-doped LiMn2O4 in our Li-ion battery tests: LiAl0Single Nanorod Devices for Battery Diagnostics: A Case Study on LiMn2O4 Yuan Yang, Chong Xie nanostructure devices as a powerful new diagnostic tool for batteries with LiMn2O4 nanorod materials

Cui, Yi

412

Magneto-resistive coefficient enhancement observed around Verwey-like transition on spinel ferrites XFe{sub 2}O{sub 4} (X?=?Mn, Zn)  

SciTech Connect (OSTI)

Manganese and Zinc ferrites were prepared by solid state reaction. The resulting powders were pressed into pellets and heat treated at 1100?°C. The samples were characterized by using X-ray diffraction, pure phases of zinc ferrite (ZnFe{sub 2}O{sub 4}) and manganese ferrite (MnFe{sub 2}O{sub 4}) were obtained. Scanning electron microscopy images showed a good contact between particles. A drop of electrical resistance was found in both samples, MnFe{sub 2}O{sub 4} and ZnFe{sub 2}O{sub 4}, with values going from 2750 to 130?? and from 1100 to 55??, respectively. Transition temperatures were determined to be T{sub V}?=?225?K for MnFe{sub 2}O{sub 4} and T{sub V}?=?130?K for ZnFe{sub 2}O{sub 4}. Magnetoresistance measurements were carried out in the temperature range where R showed the transition, defined as the Verwey-like transition temperature range, ?T{sub V}. No magnetoresistive effect was observed out of it. The magnetoresistive coefficient (MRC) observed at ?T{sub V} reached its maximum values of 1.1% for MnFe{sub 2}O{sub 4} and 6.68% for ZnFe{sub 2}O{sub 4}. The differences between MRC values are related to the divalent metal element used. Finally, the magnetoresistive response indicates that the electrical transition observed is strongly influencing the magnetoresistance; where the underlying responsible for this behavior could be a charge reordering occurring at the Verwey-like transition temperature.

López Maldonado, K. L., E-mail: liliana.lopez.maldonado@gmail.com; Vazquez Zubiate, L.; Elizalde Galindo, J. T. [Instituto de Ingeniería y Tecnología, Universidad Autónoma de Ciudad Juárez, Av. Del Charro 450 norte, 32310 Ciudad Juárez (Mexico); Presa, P. de la [Instituto de Magnetismo Aplicado (UCM-ADIF-CSIC), P.O. Box 155, 28230 Las Rozas (Spain); Departamento de Física de Materiales, Univ. Complutense de Madrid, Madrid (Spain); Matutes Aquino, J. A. [Centro de Investigación en Materiales Avanzados, Miguel de Cervantes 120, 31109 Chihuahua (Mexico)

2014-05-07T23:59:59.000Z

413

Heat and Power Systems Design  

E-Print Network [OSTI]

HEAT AND POWER SYSTEMS DESIGN H. D. Spriggs and J. V. Shah, Leesburg. VA ABSTRACT The selection of heat and power systems usually does not include a thorough analysis of the process heating. cooling and power requirements. In most cases..., these process requirements are accepted as specifications before heat and power systems are selected and designed. In t~is article we describe how Process Integration using Pinch Technology can be used to understand and achieve the minimum process heating...

Spriggs, H. D.; Shah, J. V.

414

Heat distribution ceramic processing method  

DOE Patents [OSTI]

A multi-layered heat distributor system is provided for use in a microwave process. The multi-layered heat distributors includes a first inner layer of a high thermal conductivity heat distributor material, a middle insulating layer and an optional third insulating outer layer. The multi-layered heat distributor system is placed around the ceramic composition or article to be processed and located in a microwave heating system. Sufficient microwave energy is applied to provide a high density, unflawed ceramic product.

Tiegs, Terry N. (Lenoir City, TN); Kiggans, Jr., James O. (Oak Ridge, TN)

2001-01-01T23:59:59.000Z

415

Acoustical heat pumping engine  

DOE Patents [OSTI]

The disclosure is directed to an acoustical heat pumping engine without moving seals. A tubular housing holds a compressible fluid capable of supporting an acoustical standing wave. An acoustical driver is disposed at one end of the housing and the other end is capped. A second thermodynamic medium is disposed in the housing near to but spaced from the capped end. Heat is pumped along the second thermodynamic medium toward the capped end as a consequence both of the pressure oscillation due to the driver and imperfect thermal contact between the fluid and the second thermodynamic medium. 2 figs.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1983-08-16T23:59:59.000Z

416

Air heating system  

DOE Patents [OSTI]

A self-starting, fuel-fired, air heating system including a vapor generator, a turbine, and a condenser connected in a closed circuit such that the vapor output from the vapor generator is conducted to the turbine and then to the condenser where it is condensed for return to the vapor generator. The turbine drives an air blower which passes air over the condenser for cooling the condenser. Also, a condensate pump is driven by the turbine. The disclosure is particularly concerned with the provision of heat exchanger and circuitry for cooling the condensed fluid output from the pump prior to its return to the vapor generator.

Primeau, John J. (19800 Seminole Rd., Euclid, OH 44117)

1983-03-01T23:59:59.000Z

417

Solar industrial process heat  

SciTech Connect (OSTI)

The aim of the assessment reported is to candidly examine the contribution that solar industrial process heat (SIPH) is realistically able to make in the near and long-term energy futures of the United States. The performance history of government and privately funded SIPH demonstration programs, 15 of which are briefly summarized, and the present status of SIPH technology are discussed. The technical and performance characteristics of solar industrial process heat plants and equipment are reviewed, as well as evaluating how the operating experience of over a dozen SIPH demonstration projects is influencing institutional acceptance and economoc projections. Implications for domestic energy policy and international implications are briefly discussed. (LEW)

Lumsdaine, E.

1981-04-01T23:59:59.000Z

418

Acoustical heat pumping engine  

DOE Patents [OSTI]

The disclosure is directed to an acoustical heat pumping engine without moving seals. A tubular housing holds a compressible fluid capable of supporting an acoustical standing wave. An acoustical driver is disposed at one end of the housing and the other end is capped. A second thermodynamic medium is disposed in the housing near to but spaced from the capped end. Heat is pumped along the second thermodynamic medium toward the capped end as a consequence both of the pressure oscillation due to the driver and imperfect thermal contact between the fluid and the second thermodynamic medium.

Wheatley, John C. (Los Alamos, NM); Swift, Gregory W. (Los Alamos, NM); Migliori, Albert (Santa Fe, NM)

1983-08-16T23:59:59.000Z

419

Preparation and electrochemical properties of lamellar MnO{sub 2} for supercapacitors  

SciTech Connect (OSTI)

Lamellar birnessite-type MnO{sub 2} materials were prepared by changing the pH of the initial reaction system via hydrothermal synthesis. The interlayer spacing of MnO{sub 2} with a layered structure increased gradually when the initial pH value varied from 12.43 to 2.81, while the MnO{sub 2}, composed of {alpha}-MnO{sub 2} and {gamma}-MnO{sub 2}, had a rod-like structure at pH 0.63. Electrochemical studies indicated that the specific capacitance of birnessite-type MnO{sub 2} was much higher than that of rod-like MnO{sub 2} at high discharge current densities due to the lamellar structure with fast intercalation/deintercalation of protons and high utilization of MnO{sub 2}. The initial specific capacitance of MnO{sub 2} prepared at pH 2.81 was 242.1 F g{sup -1} at 2 mA cm{sup -2} in 2 mol L{sup -1} (NH{sub 4}){sub 2}SO{sub 4} aqueous electrolyte. The capacitance increased by about 8.1% of initial capacitance after 200 cycles at a current density of 100 mA cm{sup -2}.

Yan, Jun; Wei, Tong [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Material Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China)] [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Material Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Cheng, Jie [Research Institute of Chemical Defense, Beijing 100083 (China)] [Research Institute of Chemical Defense, Beijing 100083 (China); Fan, Zhuangjun, E-mail: fanzhj666@163.com [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Material Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China)] [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Material Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Zhang, Milin [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Material Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China)] [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, College of Material Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China)

2010-02-15T23:59:59.000Z

420

Distinct local electronic structure and magnetism for Mn in amorphous Si and Ge  

SciTech Connect (OSTI)

Transition metals such as Mn generally have large local moments in covalent semiconductors due to their partially filled d shells. However, Mn magnetization in group-IV semiconductors is more complicated than often recognized. Here we report a striking crossover from a quenched Mn moment (<0.1 {mu}{sub B}) in amorphous Si (a-Si) to a large distinct local Mn moment ({ge}3{mu}{sub B}) in amorphous Ge (a-Ge) over a wide range of Mn concentrations (0.005-0.20). Corresponding differences are observed in d-shell electronic structure and the sign of the Hall effect. Density-functional-theory calculations show distinct local structures, consistent with different atomic density measured for a-Si and a-Ge, respectively, and the Mn coordination number N{sub c} is found to be the key factor. Despite the amorphous structure, Mn in a-Si is in a relatively well-defined high coordination interstitial type site with broadened d bands, low moment, and electron (n-type) carriers, while Mn in a-Ge is in a low coordination substitutional type site with large local moment and holes (p-type) carriers. Moreover, the correlation between N{sub c} and the magnitude of the local moment is essentially independent of the matrix; the local Mn moments approach zero when N{sub c} > 7 for both a-Si and a-Ge.

Zeng, Li; Cao, J. X.; Helgren, E.; Karel, J.; Arenholz, E.; Ouyang, Lu; Smith, David J.; Wu, R. Q.; Hellman, F.

2010-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Strain mediated coupling in magnetron sputtered multiferroic PZT/Ni-Mn-In/Si thin film heterostructure  

SciTech Connect (OSTI)

The strain mediated electrical and magnetic properties were investigated in PZT/Ni-Mn-In heterostructure deposited on Si (100) by dc/rf magnetron sputtering. X-ray diffraction pattern revealed that (220) orientation of Ni-Mn-In facilitate the (110) oriented tertragonal phase growth of PZT layer in PZT/Ni-Mn-In heterostructure. A distinctive peak in dielectric constant versus temperature plots around martensitic phase transformation temperature of Ni-Mn-In showed a strain mediated coupling between Ni-Mn-In and PZT layers. The ferroelectric measurement taken at different temperatures exhibits a well saturated and temperature dependent P-E loops with a highest value of P{sub sat}???55 ?C/cm{sup 2} obtained during martensite-austenite transition temperature region of Ni-Mn-In. The stress induced by Ni-Mn-In layer on upper PZT film due to structural transformation from martensite to austenite resulted in temperature modulated Tunability of PZT/Ni-Mn-In heterostructure. A tunability of 42% was achieved at 290?K (structural transition region of Ni-Mn-In) in these heterostructures. I-V measurements taken at different temperatures indicated that ohmic conduction was the main conduction mechanism over a large electric field range in these heterostructures. Magnetic measurement revealed that heterostructure was ferromagnetic at room temperature with a saturation magnetization of ?123?emu/cm{sup 3}. Such multiferroic heterostructures exhibits promising applications in various microelectromechanical systems.

Singh, Kirandeep; Kaur, Davinder, E-mail: dkaurfph@iitr.ernet.in [Functional Nanomaterials Research Lab, Department of Physics and Centre of Nanotechnology, Indian Institute of Technology Roorkee, Roorkee-247667, Uttarakhand (India); Singh, Sushil Kumar [Functional Materials Division, Solid State Physics Lab (SSPL), DRDO, Lucknow Road, Timarpur, Delhi 110054 (India)

2014-09-21T23:59:59.000Z

422

APPARENT WATER OPTICAL PROPERTIES AT THE CARIBBEAN TIME SERIES STATION  

E-Print Network [OSTI]

APPARENT WATER OPTICAL PROPERTIES AT THE CARIBBEAN TIME SERIES STATION Roy A. Armstrong, Jose M of Puerto Rico Mayagüez, Puerto Rico 00681 ABSTRACT The Caribbean Time Series, located 28 nautical miles in near- surface waters of the northeastern Caribbean Basin. Apparent optical properties such as, remote

Gilbes, Fernando

423

MET Stations and Web Cams in the Great Lakes  

E-Print Network [OSTI]

in Alpena, MI, Muskegon, MI, South Haven, MI, Michigan City, IN, Chicago, IL, and Toldeo, OH also include: Alpena, MI Chicago, IL Muskegon, MI Michigan City, IN South Haven, MI Toledo, OH Met Data Stations: Alpena, MI Chicago, IL Michigan City, IN Milwaukee, WI Muskegon, MI South Haven, MI Thunder Bay

424

National Aeronautics and Space Administration International Space Station  

E-Print Network [OSTI]

and technological endeavor ever undertaken, involving support from five space agencies representing 16 nations. Once's solar panels exceed the wingspan of a Boeing 777 jetliner and harness enough energy from the sunNational Aeronautics and Space Administration NASAfacts International Space Station Clearly

425

Great Lakes Hydrometeorological Station Directory Database and Internet Web Development  

E-Print Network [OSTI]

Great Lakes Hydrometeorological Station Directory Database and Internet Web Development Primary Investigator: Thomas Croley - NOAA GLERL (Emeritus) This project was completed in 2001 Overview A new directory in hydrometeorological data availability with in the Great Lakes. The new directory will consist of an updated database

426

DEVELOPMENT OF A TURNKEY COMMERCIAL HYDROGEN FUELING STATION  

E-Print Network [OSTI]

of the hydrogen fuel economy for buses, fleet vehicles, and ultimately personal vehicles. In order to demonstrate to the reforming of natural gas to produce a reformate stream; · Develop an efficient, cost-effective means the basis for future commercial Fueling Stations. 1 Proceedings of the 2002 U.S. DOE Hydrogen Program Review

427

VISITOR PARKING Pay station parking meters are available around  

E-Print Network [OSTI]

temporary parking needs. Daily scratch-off permits are available in advance from Parking Services. LOT METER PAY STATION RATES (SUMMER RATES MAY BE DISCOUNTED) HOW DO I GET A PERMIT? When parking on campus, a CSM parking permit is required Monday through Friday, from 7AM until 5 PM. Permits authorize parking

428

Bryan Balkenbush Fukushima Daiichi Nuclear Power Station `Issue'  

E-Print Network [OSTI]

Bryan Balkenbush Fukushima Daiichi Nuclear Power Station `Issue' Map: Timeline: March 11th, sparking a tsunami March 14th : Explosion reported by second nuclear reactor, authorities scramble to cool reactors to avoid full nuclear meltdown March 15th : A second explosion occurs in reactor 4. Radiation

Toohey, Darin W.

429

A summary of North American HVDC converter station reliability specifications  

SciTech Connect (OSTI)

This paper summarizes Reliability, Availability, and Maintainability (RAM) specifications that were issued for thyristor based HVDC converter stations in service in North America. A total of twenty project specifications are summarized. A detailed summary by project is shown with specific quantitative requirements categorized. Definitions of terms, representative design principles, and formulas used in calculating RAM parameters contained in existing reliability specifications are presented.

Vancers, I. (ABB Power Systems Inc., Los Angeles, CA (United States)); Hormozi, F.J. (Los Angeles Dept. of Water and Power, CA (United States))

1993-07-01T23:59:59.000Z

430

Station GPS permanente IPG Paris DGF Uchile UNAP Iquique  

E-Print Network [OSTI]

NetRS, Antenna TRIMBLE Zephyr geodetic and autonomous energy (battery and solar panel). HISTORIC Semi.71476292 - 69.82727839 1675.36 DESCRIPTION North Chile II region, semi-permanent GPS station IPGP / DGF network American but in the convergence area of Nazca/ SOAM plates. Approximate Position X coordinate (m) : 2044899

Vigny, Christophe

431

Station GPS permanente IPG Paris DGF Uchile UNAP Iquique  

E-Print Network [OSTI]

-glue. Receptor TRIMBLE NetRS, Antenna TRIMBLE Zephyr geodetic and autonomous energy (battery and solar panel Coordinates : URCU : -21.763750 - 70.152917 DESCRIPTION North Chile II region, semi-permanent GPS station American but in the convergence area of Nazca/ SOAM plates. Approximate Position X coordinate (m) : Y

Vigny, Christophe

432

Heat driven heat pump using paired ammoniated salts  

SciTech Connect (OSTI)

A cycle for a heat driven heat pump using two salts CaCl/sup 2/.8NH/sup 3/, and ZnCl/sup 2/.4NH3 which may reversibly react with ammonia with the addition or evolution of heat. These salts were chosen so that both ammoniation processes occur at the same temperature so that the heat evolved may be used for comfort heating. The heat to drive the system need only be slightly hotter than 122 C. The low temperature source need only be slightly warmer than 0 C.

Dunlap, R.M.

1980-08-29T23:59:59.000Z

433

Heat-transfer coefficients in agitated vessels. Latent heat models  

SciTech Connect (OSTI)

Latent heat models were developed to calculate heat-transfer coefficients in agitated vessels for two cases: (1) heating with a condensable fluid flowing through coils and jackets; (2) vacuum reflux cooling with an overhead condenser. In either case the mathematical treatment, based on macroscopic balances, requires no iterative schemes. In addition to providing heat-transfer coefficients, the models predict flow rates of service fluid through the coils and jackets, estimate the percentage of heat transfer due to latent heat, and compute reflux rates.

Kumpinsky, E. [Ashland Chemical Co., Columbus, OH (United States)] [Ashland Chemical Co., Columbus, OH (United States)

1996-03-01T23:59:59.000Z

434

Experimental Research on Solar Assisted Heat Pump Heating System with Latent Heat Storage  

E-Print Network [OSTI]

-reaching meaning of solving energy and environment problems if new type energy conservation and environment protection heating system ? solar assisted ground-source heat pump (SAGHP) heating system with a latent heat storage tank will be practical... was established at the laboratory of construction energy conservation in Harbin Institute of Technology (HIT) in 2004. It added a latent heat storage tank in original SAGHP system. The schematic diagram of the system is shown in Figure 1. The experimental...

Han, Z.; Zheng, M.; Liu, W.; Wang, F.

2006-01-01T23:59:59.000Z

435

Wastewater heat recovery apparatus  

DOE Patents [OSTI]

A heat recovery system is described with a heat exchanger and a mixing valve. A drain trap includes a heat exchanger with an inner coiled tube, baffle plate, wastewater inlet, wastewater outlet, cold water inlet, and preheated water outlet. Wastewater enters the drain trap through the wastewater inlet, is slowed and spread by the baffle plate, and passes downward to the wastewater outlet. Cold water enters the inner tube through the cold water inlet and flows generally upward, taking on heat from the wastewater. This preheated water is fed to the mixing valve, which includes a flexible yoke to which are attached an adjustable steel rod, two stationary zinc rods, and a pivoting arm. The free end of the arm forms a pad which rests against a valve seat. The rods and pivoting arm expand or contract as the temperature of the incoming preheated water changes. The zinc rods expand more than the steel rod, flexing the yoke and rotating the pivoting arm. The pad moves towards the valve seat as the temperature of the preheated water rises, and away as the temperature falls, admitting a variable amount of hot water to maintain a nearly constant average process water temperature. 6 figs.

Kronberg, J.W.

1992-09-01T23:59:59.000Z

436

Wastewater heat recovery apparatus  

DOE Patents [OSTI]

A heat recovery system with a heat exchanger and a mixing valve. A drain trap includes a heat exchanger with an inner coiled tube, baffle plate, wastewater inlet, wastewater outlet, cold water inlet, and preheated water outlet. Wastewater enters the drain trap through the wastewater inlet, is slowed and spread by the baffle plate, and passes downward to the wastewater outlet. Cold water enters the inner tube through the cold water inlet and flows generally upward, taking on heat from the wastewater. This preheated water is fed to the mixing valve, which includes a flexible yoke to which are attached an adjustable steel rod, two stationary zinc rods, and a pivoting arm. The free end of the arm forms a pad which rests against a valve seat. The rods and pivoting arm expand or contract as the temperature of the incoming preheated water changes. The zinc rods expand more than the steel rod, flexing the yoke and rotating the pivoting arm. The pad moves towards the valve seat as the temperature of the preheated water rises, and away as the temperature falls, admitting a variable amount of hot water to maintain a nearly constant average process water temperature.

Kronberg, James W. (108 Independent Blvd., Aiken, SC 29801)

1992-01-01T23:59:59.000Z

437

THERMOCHEMICAL HEAT STORAGE FOR CONCENTRATED SOLAR POWER  

SciTech Connect (OSTI)

Thermal energy storage (TES) is an integral part of a concentrated solar power (CSP) system. It enables plant operators to generate electricity beyond on sun hours and supply power to the grid to meet peak demand. Current CSP sensible heat storage systems employ molten salts as both the heat transfer fluid and the heat storage media. These systems have an upper operating temperature limit of around 400 C. Future TES systems are expected to operate at temperatures between 600 C to 1000 C for higher thermal efficiencies which should result in lower electricity cost. To meet future operating temperature and electricity cost requirements, a TES concept utilizing thermochemical cycles (TCs) based on multivalent solid oxides was proposed. The system employs a pair of reduction and oxidation (REDOX) reactions to store and release heat. In the storage step, hot air from the solar receiver is used to reduce the oxidation state of an oxide cation, e.g. Fe3+ to Fe2+. Heat energy is thus stored as chemical bonds and the oxide is charged. To discharge the stored energy, the reduced oxide is re-oxidized in air and heat is released. Air is used as both the heat transfer fluid and reactant and no storage of fluid is needed. This project investigated the engineering and economic feasibility of this proposed TES concept. The DOE storage cost and LCOE targets are $15/kWh and $0.09/kWh respectively. Sixteen pure oxide cycles were identified through thermodynamic calculations and literature information. Data showed the kinetics of re-oxidation of the various oxides to be a key barrier to implementing the proposed concept. A down selection was carried out based on operating temperature, materials costs and preliminary laboratory measurements. Cobalt oxide, manganese oxide and barium oxide were selected for developmental studies to improve their REDOX reaction kinetics. A novel approach utilizing mixed oxides to improve the REDOX kinetics of the selected oxides was proposed. It partially replaces some of the primary oxide cations with selected secondary cations. This causes a lattice charge imbalance and increases the anion vacancy density. Such vacancies enhance the ionic mass transport and lead to faster re-oxidation. Reoxidation fractions of Mn3O4 to Mn2O3 and CoO to Co3O4 were improved by up to 16 fold through the addition of a secondary oxide. However, no improvement was obtained in barium based mixed oxides. In addition to enhancing the short term re-oxidation kinetics, it was found that the use of mixed oxides also help to stabilize or even improve the TES properties after long term thermal cycling. Part of this improvement could be attributed to a reduced grain size in the mixed oxides. Based on the measurement results, manganese-iron, cobalt-aluminum and cobalt iron mixed oxides have been proposed for future engineering scale demonstration. Using the cobalt and manganese mixed oxides, we were able to demonstrate charge and discharge of the TES media in both a bench top fixed bed and a rotary kiln-moving bed reactor. Operations of the fixed bed configuration are straight forward but require a large mass flow rate and higher fluid temperature for charging. The rotary kiln makes direct solar irradiation possible and provides significantly better heat transfer, but designs to transport the TES oxide in and out of the reactor will need to be defined. The final reactor and system design will have to be based on the economics of the CSP plant. A materials compatibility study was also conducted and it identified Inconel 625 as a suitable high temperature engineering material to construct a reactor holding either cobalt or manganese mixed oxides. To assess the economics of such a CSP plant, a packed bed reactor model was established as a baseline. Measured cobalt-aluminum oxide reaction kinetics were applied to the model and the influences of bed properties and process parameters on the overall system design were investigated. The optimal TES system design was found to be a network of eight fixed bed reactors at 18.75 MWth each with charge and

PROJECT STAFF

2011-10-31T23:59:59.000Z

438

Thermal Stability of MnBi Magnetic Materials. | EMSL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched Ferromagnetism in Layered NbS2 andThe1 MembersStability of MnBi Magnetic Materials.

439

Electronic Structure and Oxidation State Changes in the Mn4Ca Cluster of Photosystem II  

SciTech Connect (OSTI)

Oxygen-evolving complex (Mn4Ca cluster) of Photosystem II cycles through five intermediate states (Si-states, i =0-4) before a molecule of dioxygen is released. During the S-state transitions, electrons are extracted from the OEC, either from Mn or alternatively from a Mn ligand. The oxidation state of Mn is widely accepted as Mn4(III2,IV2) and Mn4(III,IV3) for S1 and S2 states, while it is still controversial for the S0 and S3 states. We used resonant inelastic X-ray scattering (RIXS) to study the electronic structure of Mn4Ca complex in the OEC. The RIXS data yield two-dimensional plots that provide a significant advantage by obtaining both K-edge pre-edge and L-edge-like spectra (metal spin state) simultaneously. We have collected data from PSII samples in the each of the S-states and compared them with data from various inorganic Mncomplexes. The spectral changes in the Mn 1s2p3/2 RIXS spectra between the S-states were compared to those of the oxides of Mn and coordination complexes. The results indicate strong covalency for the electronic configuration in the OEC, and we conclude that the electron is transferred from a strongly delocalized orbital, compared to those in Mn oxides or coordination complexes. The magnitude for the S0 to S1, and S1 to S2 transitions is twice as large as that during the S2 to S3 transition, indicating that the electron for this transition is extracted from a highly delocalized orbital with little change in charge density at the Mn atoms.

Yano, Junko; Pushkar, Yulia; Messinger, Johannes; Bergmann, Uwe; Glatzel, Pieter; Yachandra, Vittal K

2007-08-03T23:59:59.000Z

440

Protective effects of ebselen (Ebs) and para-aminosalicylic acid (PAS) against manganese (Mn)-induced neurotoxicity  

SciTech Connect (OSTI)

Chronic, excessive exposure to manganese (Mn) may induce neurotoxicity and cause an irreversible brain disease, referred to as manganism. Efficacious therapies for the treatment of Mn are lacking, mandating the development of new interventions. The purpose of the present study was to investigate the efficacy of ebselen (Ebs) and para-aminosalicylic acid (PAS) in attenuating the neurotoxic effects of Mn in an in vivo rat model. Exposure biomarkers, inflammatory and oxidative stress biomarkers, as well as behavioral parameters were evaluated. Co-treatment with Mn plus Ebs or Mn plus PAS caused a significant decrease in blood and brain Mn concentrations (compared to rats treated with Mn alone), concomitant with reduced brain E{sub 2} prostaglandin (PGE{sub 2}) and enhanced brain glutathione (GSH) levels, decreased serum prolactin (PRL) levels, and increased ambulation and rearing activities. Taken together, these results establish that both PAS and Ebs are efficacious in reducing Mn body burden, neuroinflammation, oxidative stress and locomotor activity impairments in a rat model of Mn-induced toxicity. -- Highlights: ? The manuscript is unique in its approach to the neurotoxicity of Mn. ? The manuscript incorporates molecular, cellular and functional (behavioral) analyses. ? Both PAS and Ebs are effective in restoring Mn behavioral function. ? Both PAS and Ebs are effective in reducing Mn-induced oxidative stress. ? Both PAS and Ebs led to a decrease in Mn-induced neuro-inflammation.

Marreilha dos Santos, A.P., E-mail: apsantos@ff.ul.pt [I-Med.UL, Department of Toxicology and Food Sciences, Faculty of Pharmacy, University of Lisbon, Lisbon (Portugal); Lucas, Rui L.; Andrade, Vanda; Mateus, M. Luísa [I-Med.UL, Department of Toxicology and Food Sciences, Faculty of Pharmacy, University of Lisbon, Lisbon (Portugal)] [I-Med.UL, Department of Toxicology and Food Sciences, Faculty of Pharmacy, University of Lisbon, Lisbon (Portugal); Milatovic, Dejan; Aschner, Michael [Department of Pediatrics, Vanderbilt University Medical Center, Nashville, TN 37232 (United States)] [Department of Pediatrics, Vanderbilt University Medical Center, Nashville, TN 37232 (United States); Batoreu, M. Camila [I-Med.UL, Department of Toxicology and Food Sciences, Faculty of Pharmacy, University of Lisbon, Lisbon (Portugal)] [I-Med.UL, Department of Toxicology and Food Sciences, Faculty of Pharmacy, University of Lisbon, Lisbon (Portugal)

2012-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Low Level Heat Recovery Through Heat Pumps and Vapor Recompression  

E-Print Network [OSTI]

The intent of this paper is to examine the methods and economics of recovering low level heat through heat pumps and vapor recompression. Actual commercially available equipment is considered to determine the near-term and future economic viability...

Gilbert, J.

1980-01-01T23:59:59.000Z

442

TRANSPARENT HEAT MIRRORS FOR PASSIVE SOLAR HEATING APPLICATIONS  

E-Print Network [OSTI]

heating purposes. BACKGROUND The reduction of heat transfer rates by the use of thermal infraredheating applications should become available on the marketplace. Due to their high reflectivity to thermal infrared

Selkowitz, S.

2011-01-01T23:59:59.000Z

443

Heat Transfer Derivation of differential equations for heat transfer conduction  

E-Print Network [OSTI]

) or kW *h or Btu. U is the change in stored energy, in units of kW *h (kWh) or Btu. qx is the heat conducted (heat flux) into the control volume at surface edge x, in units of kW/m2 or Btu/(h-ft2). qx volume is positive), in kW/m3 or Btu/(h-ft3) (a heat sink, heat drawn out of the volume, is negative

Veress, Alexander

444

Le Prata Geothermal Power Station | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429Lacey, Washington:Lakeville, MN)Lauderhill,5. It isLawrenceville, NewLazyPrata

445

Heat-transfer coefficients in agitated vessels. Sensible heat models  

SciTech Connect (OSTI)

Transient models for sensible heat were developed to assess the thermal performance of agitated vessels with coils and jackets. Performance is quantified with the computation of heat-transfer coefficients by introducing vessel heating and cooling data into model equations. Of the two model categories studied, differential and macroscopic, the latter is preferred due to mathematical simplicity and lower sensitivity to experimental data variability.

Kumpinsky, E. [Ashland Chemical Co., Columbus, OH (United States). Research and Development Dept.

1995-12-01T23:59:59.000Z

446

Heat engine Device that transforms heat into work.  

E-Print Network [OSTI]

, and rocket engines are heat engines. So are steam engines and turbines #12;2 refrigerator Device that uses by steam turbines. Steam turbines, jet engines and rocket engines use a Brayton cycle #12;4 Steam turbines1 Heat engine Device that transforms heat into work. It requires two energy reservoirs at different

Winokur, Michael

447

Fast reactor power plant design having heat pipe heat exchanger  

DOE Patents [OSTI]

The invention relates to a pool-type fission reactor power plant design having a reactor vessel containing a primary coolant (such as liquid sodium), and a steam expansion device powered by a pressurized water/steam coolant system. Heat pipe means are disposed between the primary and water coolants to complete the heat transfer therebetween. The heat pipes are vertically oriented, penetrating the reactor deck and being directly submerged in the primary coolant. A U-tube or line passes through each heat pipe, extended over most of the length of the heat pipe and having its walls spaced from but closely proximate to and generally facing the surrounding walls of the heat pipe. The water/steam coolant loop includes each U-tube and the steam expansion device. A heat transfer medium (such as mercury) fills each of the heat pipes. The thermal energy from the primary coolant is transferred to the water coolant by isothermal evaporation-condensation of the heat transfer medium between the heat pipe and U-tube walls, the heat transfer medium moving within the heat pipe primarily transversely between these walls.

Huebotter, P.R.; McLennan, G.A.

1984-08-30T23:59:59.000Z

448

Fast reactor power plant design having heat pipe heat exchanger  

DOE Patents [OSTI]

The invention relates to a pool-type fission reactor power plant design having a reactor vessel containing a primary coolant (such as liquid sodium), and a steam expansion device powered by a pressurized water/steam coolant system. Heat pipe means are disposed between the primary and water coolants to complete the heat transfer therebetween. The heat pipes are vertically oriented, penetrating the reactor deck and being directly submerged in the primary coolant. A U-tube or line passes through each heat pipe, extended over most of the length of the heat pipe and having its walls spaced from but closely proximate to and generally facing the surrounding walls of the heat pipe. The water/steam coolant loop includes each U-tube and the steam expansion device. A heat transfer medium (such as mercury) fills each of the heat pipes. The thermal energy from the primary coolant is transferred to the water coolant by isothermal evaporation-condensation of the heat transfer medium between the heat pipe and U-tube walls, the heat transfer medium moving within the heat pipe primarily transversely between these walls.

Huebotter, Paul R. (Western Springs, IL); McLennan, George A. (Downers Grove, IL)

1985-01-01T23:59:59.000Z

449

MERCURY SPECIATION SAMPLING AT NEW CENTURY ENERGY'S VALMONT STATION  

SciTech Connect (OSTI)

The 1990 Clean Air Act Amendments required the U.S. Environmental Protection Agency (EPA) to determine whether the presence of mercury in the stack emissions from fossil fuel-fired electric utility power plants poses an unacceptable public health risk. EPA's conclusions and recommendations were presented in the ''Mercury Study Report to Congress'' and ''Study of Hazardous Air Pollutant Emissions from Electric Utility Steam Generating Units''. The first report addressed both the human health and environmental effects of anthropogenic mercury emissions, while the second addressed the risk to public health posed by the emission of mercury and other hazardous air pollutants from steam electric generating units. Although these reports did not state that mercury controls on coal-fired electric power stations would be required given the current state of the art, they did indicate that the EPA views mercury as a potential threat to human health. Therefore, it was concluded that mercury controls at some point may be necessary. EPA also indicated that additional research/information was necessary before any definitive statement could be made. In an effort to determine the amount and types of mercury being emitted into the atmosphere by coal-fired power plants, EPA in late 1998 issued an information collection request (ICR) that required all coal-fired power plants to analyze their coal and submit the results to EPA on a quarterly basis. In addition, about 85 power stations were required to measure the speciated mercury concentration in the flue gas. These plants were selected on the basis of plant configuration and coal type. The Valmont Station owned and operated by New Century Energy in Boulder, Colorado, was selected for detailed mercury speciation of the flue gas as part of the ICR process. New Century Energy, in a tailored collaboration with EPRI and the U.S. Department of Energy, contracted with the Energy & Environmental Research Center (EERC) to do a study evaluating the behavior of mercury at the Valmont Station. The activities conducted at the Valmont Station by the EERC not only included the sampling needed to meet the requirements of the ICR, but involved a much more extensive mercury research program. The following objectives for the sampling at New Century Energy's Valmont Station were accomplished: (1) Successfully complete all of the mercury sampling and reporting requirements of the ICR. (2) Determine the variability in mercury concentrations at the stack using mercury continuous emission monitors (CEMs). (3) Calculate mercury mass balances and emission rates. (4) Determine the mercury concentration in the fly ash as a function of particle size. (5) Determine the impact of a fabric filter on mercury emissions for a western bituminous coal.

Dennis L. Laudal

2000-04-01T23:59:59.000Z

450

Minnesota Innovation Partnerships (MN-IP) Try and Buy MN-IP Try and Buy --for companies interested in licensing existing U of M inventions  

E-Print Network [OSTI]

is executed BUY (LICENSE) · Low, published royalty rate, with first $1 million of product sales royalty-free · Royalty rates based on industry comparables · Royalty rate discount for MN operating companies2 · Royalty

Minnesota, University of

451

Exchange interaction mediated ferroelectricity in multiferroic MnTiO{sub 3} with anisotropic orbital hybridization and hole delocalization  

SciTech Connect (OSTI)

We present the orbital structure of MnTiO{sub 3} with polarization dependent x-ray absorption and resonant x-ray emission spectra accompanied with electronic structure calculations. The results clearly indicate a strongly anisotropic O 2p-Mn 3d orbital hybridization whereas the Mn 3d hole state shows a highly delocalized characteristic ascribed to the 3d-4p mixing. The extended Mn 4p orbital could enhance the exchange interaction between Mn (3d)-O (2p)-Mn (3d) leading to an asymmetric charge distribution in Mn-O bonds. The delocalized characteristic of Mn 3d holes is indispensable to the mechanism of spin-dependent-metal-ligand hybridization to explain magnetically induced ferroelectricity.

Chen, S. W.; Fu, S. W.; Lee, J. M.; Lee, J. F.; Pao, C. W.; Ishii, H.; Tsuei, K. D.; Hiraoka, N.; Lu, K. T.; Chen, J. M., E-mail: jeng@phys.nthu.edu.tw, E-mail: xiaolin@uow.edu.au, E-mail: jmchen@nsrrc.org.tw [National Synchrotron Radiation Research Center, Hsinchu 30076, Taiwan (China); Lin, P. A. [Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Jeng, H. T., E-mail: jeng@phys.nthu.edu.tw, E-mail: xiaolin@uow.edu.au, E-mail: jmchen@nsrrc.org.tw [Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Institute of Physics, Academia Sinica, Taipei 11529, Taiwan (China); Chen, D. P.; Dou, S. X.; Wang, X. L., E-mail: jeng@phys.nthu.edu.tw, E-mail: xiaolin@uow.edu.au, E-mail: jmchen@nsrrc.org.tw [Institute for Superconducting and Electronic Materials, Australian Institute of Innovative, Materials, University of Wollongong, North Wollongong, NSW 2500 (Australia)

2014-02-24T23:59:59.000Z

452

An Analysis of Mn-Zn Ferrite Microstructure by Impedance Spectroscopy, STEM and EDS Characterisations.  

E-Print Network [OSTI]

An Analysis of Mn-Zn Ferrite Microstructure by Impedance Spectroscopy, STEM and EDS.loyau@satie.ens-cachan.fr Abstract AC resistivity measurement results on Mn-Zn sintered ferrite were analyzed in the 0.1-500 MHz of the main limitations in frequency increase is the energy dissipations by losses in ferrites that produce

Boyer, Edmond

453

Short communication The composite rods of MnO and multi-walled carbon nanotubes as  

E-Print Network [OSTI]

Short communication The composite rods of MnO and multi-walled carbon nanotubes as anode materialsO as an anode material for lithium ion batteries are significantly improved. The MnO/MWNTs composite shows a Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education, Xi'an Jiaotong

Ceder, Gerbrand

454

Structural, Electrochemical, and Spectroscopic Investigation of Acetate Bridged Dinuclear Tetrakis-Schiff Base Macrocycles of Mn  

E-Print Network [OSTI]

resembling the oxygen-evolving complex (OEC) in photosystem II and dimanganese catalase enzymes, resulting+ and Zn2LAc+ , the two metal centers are bridged by an acetate ligand. [Mn2LAc](ClO4)·(DMF)0.5, [Mn2LAc for substrate molecules bound to redox active metal centers.5-10 In 1970, Robson showed that dinuclear tetrakis

Dinolfo, Peter H.

455

Semimetallic antiferromagnetism in the half-Heusler compound CuMnSb Ruben Weht,2  

E-Print Network [OSTI]

CuMnSb, the first antiferromagnet AFM in the Mn-based class of Heuslers and half-Heuslers that contains several conventional and half metallic ferromagnets, shows a peculiar stability of its magnetic order in high magnetic fields. Density functional based studies reveal an unusual nature of its unstable

Pickett, Warren

456

NICKEL-FREE Fe-12Mn-0.2Ti ALLOY STEEL FOR CRYOGENIC APPLICATIONS  

E-Print Network [OSTI]

Parr, J. Gordon, J. Iron and Steel Inst. B, vol. 283,137 (Properties of Fe-12Mn-0.2Ti Steel at -196°C Yield Stress (FREE Fe-12Mn-O. 2Ti ALLOY STEEL FOR CRYOGENIC APPLICATIONS

Hwang, S.

2010-01-01T23:59:59.000Z

457

Tunable White-Light-Emitting Mn-Doped ZnSe Nanocrystals Vijay Kumar Sharma,  

E-Print Network [OSTI]

Tunable White-Light-Emitting Mn-Doped ZnSe Nanocrystals Vijay Kumar Sharma, Burak Guzelturk, Talha report white-light-emitting Mn-doped ZnSe nanocrystals (NCs) that are synthesized using modified orange emission (580 nm), allowed us to achieve excitation wavelength tailorable white-light generation

Demir, Hilmi Volkan

458

Photovoltaic effect in multiphase Bi-Mn-O thin J. P. Chakrabartty,1  

E-Print Network [OSTI]

Photovoltaic effect in multiphase Bi-Mn-O thin films J. P. Chakrabartty,1 R. Nechache,2,4 C and therefore the photovoltaic conversion efficiency. Specifically, a higher Bi/Mn ratio (towards unity separation. ©2013 Optical Society of America OCIS codes: (040.5350) Photovoltaic; (160.2260) Ferroelectrics

459

austenitnoj cr-mn stali: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

cr-mn stali First Page Previous Page 1 2 3 4 5 6 Next Page Last Page Topic Index 1 Cavitation erosion of laser processed Fe-Cr-Mn and Fe-Cr-Co alloys CiteSeer Summary: Received...

460

Geothermal Heat Pump Grant Program  

Broader source: Energy.gov [DOE]

The Maryland Energy Administration (MEA) offers rebates of $3,000 for residential geothermal heat pump systems and up to $4,500 for non-residential geothermal heat pump systems. The residential...

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Heat Pipes: An Industrial Application  

E-Print Network [OSTI]

This paper reviews the basics of heat pipe exchangers. Included are how they are constructed, how they operate, where they have application, and various aspects of evaluating a potential application. After discussing the technical aspects of heat...

Murray, F.

1984-01-01T23:59:59.000Z

462

Challenges in Industrial Heat Recovery  

E-Print Network [OSTI]

This presentation will address several completed and working projects involving waste heat recovery in a chemical plant. Specific examples will be shown and some of the challenges to successful implementation and operation of heat recovery projects...

Dafft, T.

2007-01-01T23:59:59.000Z

463

Heat Pumps - Theory and Applications  

E-Print Network [OSTI]

compressors (heat pumps) with actual applications in Monsanto. Guidelines for possible application areas are drawn from the analysis, and conclusions are drawn both about the usefulness of exergy analysis and about the heat pump application areas....

Altin, M.

1982-01-01T23:59:59.000Z

464

Faculty Positions Heat Transfer and  

E-Print Network [OSTI]

Faculty Positions Heat Transfer and Thermal/Energy Sciences Naval Postgraduate School Monterey-track faculty position at the assistant professor level in the areas of Heat Transfer and Thermal/Fluid Sciences

465

Residential Solar Water Heating Rebates  

Broader source: Energy.gov [DOE]

New Hampshire offers a rebate for residential solar water-heating systems and solar space-heating systems. The rebate is equal to $1,500 for systems with an annual estimated output of 5.5 MMBTU to...

466

Can You Afford Heat Recovery?  

E-Print Network [OSTI]

many companies to venture into heat recovery projects without due consideration of the many factors involved. Many of these efforts have rendered less desirable results than expected. Heat recovery in the form of recuperation should be considered...

Foust, L. T.

1983-01-01T23:59:59.000Z

467

Low Level Heat Recovery Technology  

E-Print Network [OSTI]

level heat recovery technology. This paper discusses heat distribution systems, latest developments in absorption refrigeration and organic Rankine cycles, and pressure, minimization possibilities. The relative merits and economics of the various...

O'Brien, W. J.

1982-01-01T23:59:59.000Z

468

Heat transfer probe  

DOE Patents [OSTI]

Apparatuses, systems, methods, and computer code for, among other things, monitoring the health of samples such as the brain while providing local cooling or heating. A representative device is a heat transfer probe, which includes an inner channel, a tip, a concentric outer channel, a first temperature sensor, and a second temperature sensor. The inner channel is configured to transport working fluid from an inner inlet to an inner outlet. The tip is configured to receive at least a portion of the working fluid from the inner outlet. The concentric outer channel is configured to transport the working fluid from the inner outlet to an outer outlet. The first temperature sensor is coupled to the tip, and the second temperature sensor spaced apart from the first temperature sensor.

Frank, Jeffrey I.; Rosengart, Axel J.; Kasza, Ken; Yu, Wenhua; Chien, Tai-Hsin; Franklin, Jeff

2006-10-10T23:59:59.000Z

469

Optical heat flux gauge  

DOE Patents [OSTI]

A heat flux gauge is disclosed comprising first and second thermographic phosphor layers separated by a layer of a thermal insulator, wherein each thermographic layer comprises a plurality of respective thermographic sensors in a juxtaposed relationship with respect to each other. The gauge may be mounted on a surface with the first thermographic phosphor in contact with the surface. A light source is directed at the gauge, causing the phosphors to luminesce. The luminescence produced by the phosphors is collected and its spectra analyzed in order to determine the heat flux on the surface. First and second phosphor layers must be different materials to assure that the spectral lines collected will be distinguishable. 9 figures.

Noel, B.W.; Borella, H.M.; Cates, M.R.; Turley, W.D.; MacArthur, C.D.; Cala, G.C.

1991-04-09T23:59:59.000Z

470

Analysis of the Behavior of Electric Vehicle Charging Stations with Renewable Generations  

E-Print Network [OSTI]

Analysis of the Behavior of Electric Vehicle Charging Stations with Renewable Generations Woongsup between electric vehicle charging stations (EVCSs) with renewable electricity generation facilities (REGFs electricity generation [1]. Therefore, renewable power generation will play a significant role in smart grid

Wong, Vincent

471

Fact #832: August 4, 2014 Over Half of the Refueling Stations...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

2: August 4, 2014 Over Half of the Refueling Stations in the U.S. and Canada Sell Diesel Fuel Fact 832: August 4, 2014 Over Half of the Refueling Stations in the U.S. and Canada...

472

E-Print Network 3.0 - alternative fueling station Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

plan for 1,000 stations and 2 million FECVs by 2025... continues to grow at a rapid pace. Germany, Japan, and Korea anticipate having over 300 fueling stations... the mass...

473

Industrial Heat Recovery - 1982  

E-Print Network [OSTI]

like: "Vertical, natural circulation boilers are intrinsically mbre reliable than horizontal, forced circula tion boilers.",4 and " it will be seen that horizontal tubes have much lower heat fluxes at burnout than do vertical ones, though...-steam density difference dia gram (Figure 1) has been presented repeat edly in order to indicate a significant density difference between the two phases (even close to the critical pressure) which induces natural circulation. However, this diagra...

Csathy, D.

1982-01-01T23:59:59.000Z

474

Optimization of Heat Exchanger Cleaning  

E-Print Network [OSTI]

decrease models of the heat recovery decay. A mathematical comparison of mechanical and chemical cleaning of heat exchangers has identified the most significant parameters which affect the choice between the two methods. INTRODUCTION In most... can be somewhat mitigated by periodic chemical or mechanical cleaning of the exchanger surface, and by the addition of antifoul ants. The typical decay in heat recovery capabil ity due to fou 1i ng and restoration afte r heat exchanger cleaning...

Siegell, J. H.

475

[Waste water heat recovery system  

SciTech Connect (OSTI)

The production capabilities for and field testing of the heat recovery system are described briefly. Drawings are included.

Not Available

1993-04-28T23:59:59.000Z

476

Surface alloys of icosahedral AlMnSi with phason distortions  

SciTech Connect (OSTI)

The microstructures produced by electron-beam melting and by ion-beam mixing Al/Mn and Al/Mn/Si layers on Si substrates are examined. The treatments were found to incorporate Si from the substrate into the surface alloy. Several phases formed, depending on treatment, including ..cap alpha..- and ..beta..-AlMnSi, ..mu..-AlMn (epitaxial on Si(111), and amorphous and icosahedral AlMnSi. The observed microstructures relate the novel icosahedral phase to other phases and elucidate its formation kinetics. Diffraction patterns from large icosahedral grains (up to 5 ..mu..m) show distortions in the position and shape of weak (but not strong) reflections, as predicted for phason defects in a quasicrystalline lattice, one of the structures proposed for icosahedral phases.

Follstaedt, D.M.; Knapp, J.A.

1986-12-01T23:59:59.000Z

477

Structural and Magnetic Properties of Co-Mn-Sb Thin films  

SciTech Connect (OSTI)

Thin Co-Mn-Sb films of different compositions were investigated and utilized as electrodes in alumina based magnetic tunnel junctions with CoFe counterelectrode. The preparation conditions were optimized with respect to magnetic and structural properties. The Co-Mn-Sb/Al-O interface was analyzed by x-ray absorption spectroscopy and magnetic circular dichroism with particular focus on the element-specific magnetic moments. Co-Mn-Sb crystallizes in different complex cubic structures depending on its composition. The magnetic moments of Co and Mn are ferromagnetically coupled in all cases. A tunnel magnetoresistance ratio of up to 24% at 13 K was found and indicates that Co-Mn-Sb is not a ferromagnetic half-metal. These results are compared to recent works on the structure and predictions of the electronic properties.

Meinert, M.; Schmalhorst, J.-M.; Ebke, D.; Liu, N. N.; Thomas, A.; Reiss, G.; Kanak, J.; Stobiecki, T.; Arenholz, E.

2009-12-17T23:59:59.000Z

478

Magnetism of NiMn2O4-Fe3O4 spinel interfaces  

SciTech Connect (OSTI)

We investigate the magnetic properties of the isostructural spinel-spinel interface of NiMn{sub 2}O{sub 4}(NMO)-Fe{sub 3}O{sub 4}. Although the magnetic transition temperature of the NMO film is preserved, both bulk and interface sensitive measurements demonstrate that the interface exhibits strong interfacial magnetic coupling up to room temperature. While NMO thin films have a ferrimagnetic transition temperature of 60 K, both NiFe{sub 2}O{sub 4} and MnFe{sub 2}O{sub 4} are ferrimagnetic at room temperature. Our experimental results suggest that these magnetic properties arise from a thin interdiffused region of (Fe,Mn,Ni){sub 3}O{sub 4} at the interface, leading to Mn and Ni magnetic properties similar to those of MnFe{sub 2}O{sub 4} and NiFe{sub 2}O{sub 4}.

Arenholz, Elke; Nelson-Cheeseman, B. B.; Chopdekar, R. V.; Bettinger, J. S.; Arenholz, E.; Suzuki, Y.

2007-09-13T23:59:59.000Z

479

Neutron diffraction study of MnNiGa{sub 2}—Structural and magnetic behaviour  

SciTech Connect (OSTI)

MnNiGa{sub 2} crystallizes in the L21 (Heusler) structure and has a ferromagnetic ordering temperature T{sub C}???192?K. Rietveld refinement of the neutron diffraction patterns indicates that the Ga atoms occupy the equivalent 8c position, while Mn and Ni share the 4a (0, 0, 0) and 4b (0.5, 0.5, 0.5) sites with a mixed occupancy of Mn and Ni atoms. It is found that that ?83% of Mn and ?17% Ni are located at the 4a site while ?83% of Ni and ?17% Mn occupy the 4b site. There is no evidence of a magneto-volume effect around T{sub C}. In agreement with this finding, our detailed critical exponent analyses of isothermal magnetization curves and the related Arrott plots confirm that the magnetic phase transition at T{sub C} is second order.

Wang, J. L., E-mail: jianli@uow.edu.au [Institute for Superconductivity and Electronic Materials, University of Wollongong, Wollongong, NSW 2522 (Australia); Bragg Institute, ANSTO, Lucas Heights, NSW 2234 (Australia); School of Physical, Environmental and Mathematical Sciences, The University of New South Wales, Canberra, ACT 2600 (Australia); Ma, L.; Wu, G. H. [Institute of Physics, Chinese Academy of Science, Beijing 100190 (China); Hofmann, M. [FRM-II, Technische Universität München, 85747 Garching (Germany); Avdeev, M.; Kennedy, S. J. [Bragg Institute, ANSTO, Lucas Heights, NSW 2234 (Australia); Campbell, S. J. [School of Physical, Environmental and Mathematical Sciences, The University of New South Wales, Canberra, ACT 2600 (Australia); Md Din, M. F.; Dou, S. X. [Institute for Superconductivity and Electronic Materials, University of Wollongong, Wollongong, NSW 2522 (Australia); Hoelzel, M. [FRM-II, Technische Universität München, 85747 Garching (Germany); Fachbereich Materialwissenschaften, Technische Universität Darmstadt, 64287 Darmstadt (Germany)

2014-05-07T23:59:59.000Z

480

Heat and mass transfer considerations in advanced heat pump systems  

SciTech Connect (OSTI)

Advanced heat-pump cycles are being investigated for various applications. However, the working media and associated thermal design aspects require new concepts for maintaining high thermal effectiveness and phase equilibrium for achieving maximum possible thermodynamic advantages. In the present study, the heat- and mass-transfer processes in two heat-pump systems -- those based on absorption processes, and those using refrigerant mixtures -- are analyzed. The major technical barriers for achieving the ideal performance predicted by thermodynamic analysis are identified. The analysis provides general guidelines for the development of heat- and mass-transfer equipment for advanced heat-pump systems.

Panchal, C.B.; Bell, K.J.

1992-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "heating station mn" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Heat and mass transfer considerations in advanced heat pump systems  

SciTech Connect (OSTI)

Advanced heat-pump cycles are being investigated for various applications. However, the working media and associated thermal design aspects require new concepts for maintaining high thermal effectiveness and phase equilibrium for achieving maximum possible thermodynamic advantages. In the present study, the heat- and mass-transfer processes in two heat-pump systems -- those based on absorption processes, and those using refrigerant mixtures -- are analyzed. The major technical barriers for achieving the ideal performance predicted by thermodynamic analysis are identified. The analysis provides general guidelines for the development of heat- and mass-transfer equipment for advanced heat-pump systems.

Panchal, C.B.; Bell, K.J.

1992-01-01T23:59:59.000Z

482

Characterization of industrial process waste heat and input heat streams  

SciTech Connect (OSTI)

The nature and extent of industrial waste heat associated with the manufacturing sector of the US economy are identified. Industry energy information is reviewed and the energy content in waste heat streams emanating from 108 energy-intensive industrial processes is estimated. Generic types of process equipment are identified and the energy content in gaseous, liquid, and steam waste streams emanating from this equipment is evaluated. Matchups between the energy content of waste heat streams and candidate uses are identified. The resultant matrix identifies 256 source/sink (waste heat/candidate input heat) temperature combinations. (MHR)

Wilfert, G.L.; Huber, H.B.; Dodge, R.E.; Garrett-Price, B.A.; Fassbender, L.L.; Griffin, E.A.; Brown, D.R.; Moore, N.L.

1984-05-01T23:59:59.000Z

483

Experimental and Analytical Studies on Pyroelectric Waste Heat Energy Conversion  

E-Print Network [OSTI]

Waste heat Pyroelectric energy3 Pyroelectric Waste Heat Energy Harvesting Using Heat4 Pyroelectric Waste Heat Energy Harvesting Using Relaxor

Lee, Felix

2012-01-01T23:59:59.000Z

484

Optimal sequencing site of hydro-power stations  

SciTech Connect (OSTI)

At the first stage of a hydro-power survey of a river, it is important to select the optimal hydro-power site. The most important condition to be satisfied is to determine the optimal site where the greatest and most economical amount of hydro-energy can be obtained. This paper proposes a new method in which the optimal arrangement of the hydro-power stations is determined by a computational operation using discrete data at points along the river such as the drainage area, altitude, and distance along the river channel as obtained from topographical maps instead of drawing on engineers` experiences and the intuitions of experts. The results by this method are then compared with data on existing hydro-power stations and the results planned by expert engineers to show that this new computational method is superior.

Hayashi, T.; Yoshino, F.; Waka, R. [Tottori Univ., Koyama (Japan). Dept. of Mechanical Engineering

1995-06-01T23:59:59.000Z

485

Navajo Generating Station and Air Visibility Regulations: Alternatives and Impacts  

SciTech Connect (OSTI)

Pursuant to the Clean Air Act, the U.S. Environmental Protection Agency (EPA) announced in 2009 its intent to issue rules for controlling emissions from Navajo Generating Station that could affect visibility at the Grand Canyon and at several other national parks and wilderness areas. The final rule will conform to what EPA determines is the best available retrofit technology (BART) for the control of haze-causing air pollutants, especially nitrogen oxides. While EPA is ultimately responsible for setting Navajo Generating Station's BART standards in its final rule, it will be the U.S. Department of the Interior's responsibility to manage compliance and the related impacts. This study aims to assist both Interior and EPA by providing an objective assessment of issues relating to the power sector.

Hurlbut, D. J.; Haase, S.; Brinkman, G.; Funk, K.; Gelman, R.; Lantz, E.; Larney, C.; Peterson, D.; Worley, C.; Liebsch, E.

2012-01-01T23:59:59.000Z

486

E-Print Network 3.0 - air station north Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Refueling Station... . Irvine North ... Source: California Energy Commission Collection: Energy Storage, Conversion and Utilization 3 INTERNATIONAL JOURNAL OF CLIMATOLOGY, VOL....

487

Energy 101: Geothermal Heat Pumps  

SciTech Connect (OSTI)

An energy-efficient heating and cooling alternative, the geothermal heat pump system moves heat from the ground to a building (or from a building to the ground) through a series of flexible pipe "loops" containing water. This edition of Energy 101 explores the benefits Geothermal and the science behind how it all comes together.

None

2011-01-01T23:59:59.000Z

488

Heat Pump Strategies and Payoffs  

E-Print Network [OSTI]

After evaluating numerous waste heat sources and heat pump designs for energy recovery, we have become aware that a great deal of confusion exists about the economics of heat pumps. The purpose of this article is to present some simple formulas...

Gilbert, J. S.

1982-01-01T23:59:59.000Z

489

Industrial Heat Pump Case Study  

E-Print Network [OSTI]

with operating the evaporator. The open-cycle heat pump design uses an electrically driven centrifugal compressor to recover the latent heat of the water vapor generated by the evaporator. (Steam was the original heat source but is now only needed for start...

Wagner, J. R.; Brush, F. C.

490

Spring 2014 Heat Transfer -1  

E-Print Network [OSTI]

Spring 2014 1 Heat Transfer - 1 Consider a cylindrical nuclear fuel rod of length L and diameter df and the tube at a rate m , and the outer surface of the tube is well insulated. Heat generation occurs within. The specific heat of water pc , and the thermal conductivity of the fuel rod fk are constants. The system

Virginia Tech

491

5. Heat transfer Ron Zevenhoven  

E-Print Network [OSTI]

1/120 5. Heat transfer Ron Zevenhoven �bo Akademi University Thermal and Flow Engineering / Värme Three heat transfer mechanisms Conduction Convection Radiation 2/120 Pic: B�88 �bo Akademi University | Thermal and Flow Engineering | 20500 Turku | Finland #12;3/120 5.1 Conductive heat transfer �bo Akademi

Zevenhoven, Ron

492

Energy 101: Geothermal Heat Pumps  

ScienceCinema (OSTI)

An energy-efficient heating and cooling alternative, the geothermal heat pump system moves heat from the ground to a building (or from a building to the ground) through a series of flexible pipe "loops" containing water. This edition of Energy 101 explores the benefits Geothermal and the science behind how it all comes together.

None

2013-05-29T23:59:59.000Z

493

Development of Power-head based Fan Airflow Station  

E-Print Network [OSTI]

related to the measured fan speed. Actually the measured fan speed is assumed to equal the motor synchronous speed, which is proportional to the VFD frequency. Theoretically it is not true. The difference between the synchronous speed and motor speed... the basic theory, experiment and results of the power-head based airflow station. Theory Figure 1 shows variable speed fan connection schematic. VFD is normally installed on the motor to adjust the motor speed by modulating frequency. Typically...

Wang, G.; Liu, M.

2005-01-01T23:59:59.000Z

494

Lowry Range Solar Station: Arapahoe County, Colorado (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

A partnership with industry and U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to collect solar data to support future solar power generation in the United States. The measurement station monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location. The solar measurement instrumentation is also accompanied by meteorological monitoring equipment to provide scientists with a complete picture of the solar power possibilities.

Yoder, M.; Andreas, A.

495

Nevada Power: Clark Station; Las Vegas, Nevada (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

A partnership with the University of Nevada and U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to collect solar data to support future solar power generation in the United States. The measurement station monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location. The solar measurement instrumentation is also accompanied by meteorological monitoring equipment to provide scientists with a complete picture of the solar power possibilities.

Stoffel, T.; Andreas, A.

496

Ottawa Generating Station Biomass Facility | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy ResourcesLoading map...(UtilityCounty,Orleans County, Vermont:Ottawa County, Kansas Bennington,Station

497

Genesee Power Station LP Biomass Facility | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to: navigation, searchGeauga County, Ohio: Energy ResourcesEnergyGeneralGeneseeStation LP

498

Alternative Fuels Data Center: Ethanol Fueling Station Locations  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels Data Center Home Page onAlternativeConnecticut InformationEthanolStation

499

Effective Load Management for the City of College Station  

E-Print Network [OSTI]

to reduce the overall cost of producing and distributing power. Demand reduction comes as the result of wise manage- ment of power and therefore helps not only the con- sumer by reducing costs but also the supplier by decreasing system demand during.... The greatest impact can be achieved in communities that purchase wholesale power from a separate utility supplier and have their own billing and meter reading department, and thus a real incentive to save. DEVELOPING A ?LAN BACKGROUND College Station...

Hecox, O. D.; Bauer, V.

1985-01-01T23:59:59.000Z

500

Research & Development Roadmap: Emerging Water Heating Technologies...  

Energy Savers [EERE]

Emerging Water Heating Technologies Research & Development Roadmap: Emerging Water Heating Technologies The Research and Development (R&D) Roadmap for Emerging Water Heating...