Powered by Deep Web Technologies
Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Fluorescent ballast and lamp disposal issues  

SciTech Connect

All around the world, governments, utility companies, and private businesses are attempting to reduce the amount of energy consumed. In the US alone, new economic strategies and programs are being created to facilitate this process. For instance, the recent enactment of the National Energy Policy Act, the Environmental Protection Agency`s (EPA) Green Lights Program, and a surge of utility involvement in Demand Side Management (DSM) Commercial/Industrial Direct Install and Rebate Programs. Many of these problems target commercial/industrial lighting system retrofits as one of the most cost effective avenues for reducing the consumption of energy. Due to this trend, hundreds of millions of lighting ballasts and lamps are being discarded. The benefits of these programs result in enormous reductions in fossil fuels (and subsequent carbon dioxide, sulfur dioxide, and nitrogen oxide emissions) required to generate the displaced electricity. Throughout the US, however, there is an increasing concern for the environmental impacts surrounding the accelerated disposal of both lighting ballasts and lamps. Regulations initially established were for a one by one, retirement (failure) process rather than promoted obsolescence and forced retirement of lamp groups or entire systems (truckloads of old technologies). Recognizing this trend and the potential negative environmental effects, federal, state, and local regulators are reevaluating the impacts and are being asked to promulgate policies to specifically address this situation.

Leishman, D.L. [Alta Resource Management Services, Inc., Springfield, MA (United States)

1996-12-01T23:59:59.000Z

2

The Energy Efficiency of the U.S Fluorescent Lamp Ballast Industry  

NLE Websites -- All DOE Office Websites (Extended Search)

The Energy Efficiency of the U.S Fluorescent Lamp Ballast Industry The Energy Efficiency of the U.S Fluorescent Lamp Ballast Industry Speaker(s): Francis Rubinstein Date: February 14, 2008 - 12:00pm Location: 90-3122 Fluorescent lamp ballasts are subject to DOE appliance standards and rulemaking. But currently, only ballasts for older fluorescent lamp types, such as T-12 lamps are subject to minimum efficacy limits. The majority of fluorescent lamps now being shipped (T-8 and T-5 types) type are operated by ballasts that will not be subject to DOE rule until 2011. The metric used by DOE for characterizing the electrical efficiency of the fluorescent lamp-ballast system is called Ballast Efficacy Factor (BEF). Because BEF is not normalized, it is of limited utility for rulemaking and is useless for procurement. But by normalizing BEF to the total lamp power, I have

3

ISSUANCE 2014-12-29: Energy Conservation Program: Clarification for Energy Conservation Standards and Test Procedures for Fluorescent Lamp Ballasts  

Energy.gov (U.S. Department of Energy (DOE))

Energy Conservation Program: Clarification for Energy Conservation Standards and Test Procedures for Fluorescent Lamp Ballasts

4

Performance of "Ultra-High" Efficient Electronic Ballast for HID Lamps  

E-Print Network (OSTI)

. Index Terms--Electronic ballast, HID lamps, resonant inverter, power loss modeling, Silicon Carbide (Si of >95% for the ballast. Diode bridge rectifier EMI filter Resonant Inverter Power Factor Correction 75423, USA Abstract--A new electronic ballast circuit for High Intensity Discharge (HID) lamps

Tolbert, Leon M.

5

Transport phenomena in metal-halide lamps a poly-diagnostic study  

E-Print Network (OSTI)

/ spectroscopie. Subject headings: gas discharges / metal-halide lamps / plasma diagnostics / plasma properties-halide arc lamps . . . . . . . . . . . 7 1.3 Scope of ThesisTransport phenomena in metal-halide lamps a poly-diagnostic study Tanya Nimalasuriya #12;Copyright

Eindhoven, Technische Universiteit

6

Lighting Group: Sources and Ballasts: LED Reflector Lamp  

NLE Websites -- All DOE Office Websites (Extended Search)

LED Reflector Lamp LED Reflector Lamp LED Reflector Lamp Objective LED reflector lamp The goal of this project is to develop a revolutionary new reflector lamp which offers many advantages over current incandescent reflector lamps, including: three times greater efficiency ten times the rated life greater optical and performance properties use of light emitting diodes (LEDs) to generate the light. Although LEDs have been commercially available since the late 1960’s, recent dramatic improvements in LED technology have led to white light devices with efficiencies that meet or exceed those of a standard incandescent lamp. This project will build upon these improvements to develop a new type of source for focusing light. Contact Information For more information on this project, please contact:

7

Zero energy-storage ballast for compact fluorescent lamps  

DOE Patents (OSTI)

A CFL ballast includes complementary-type switching devices connected in series with their gates connected together at a control node. The switching devices supply a resonant tank circuit which is tuned to a frequency near, but slightly lower than, the resonant frequency of a resonant control circuit. As a result, the tank circuit restarts oscillations immediately following each zero crossing of the bus voltage. Such rapid restarts avoid undesirable flickering while maintaining the operational advantages and high efficacy of the CFL ballast. 4 figs.

Schultz, W.N.; Thomas, R.J.

1999-08-31T23:59:59.000Z

8

Spatial and time-dependent distribution of plasma parameters in the metal-halide arc lamp.  

E-Print Network (OSTI)

Spatial and time-dependent distribution of plasma parameters in the metal-halide arc lamp. A. Khakhaev, L. Luizova, K. Ekimov and A. Soloviev Petrozavodsk State University, Russia The metal-halide arc lamp is an effective light source and its investigation has a long history, but even at present some

Paris-Sud XI, Université de

9

2015-01-28 Issuance: Test Procedure for Fluorescent Lamp Ballasts; Final Rule Correction  

Energy.gov (U.S. Department of Energy (DOE))

This document is a pre-publication Federal Register final rule correction regarding test procedures for fluorescent lamp ballasts, as issued by the Deputy Assistant Secretary for Energy Efficiency on January 28, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

10

New and Underutilized Technology: HID Electronic/Dimming Ballasts |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HID Electronic/Dimming Ballasts HID Electronic/Dimming Ballasts New and Underutilized Technology: HID Electronic/Dimming Ballasts October 7, 2013 - 8:51am Addthis The following information outlines key deployment considerations for HID electronic/dimming ballasts within the Federal sector. Benefits Most HID electronic/dimming ballasts, typically metal halide or high-pressure sodium lamps, are currently driven by magnetic ballasts. Several manufacturers now offer electronic ballasts for these lamps, which promise better efficiency, longer lamp life, and faster startup and re-strike. Application HID electronic/dimming ballasts are applicable in exterior/security lighting and facilities with high bay areas. Key Factors for Deployment Federal agencies must evaluate relative costs, benefits, and application of

11

2014-10-14 Issuance: Test Procedures Correction for Fluorescent Lamp Ballasts; Notice of Proposed Rulemaking  

Energy.gov (U.S. Department of Energy (DOE))

This document is a pre-publication Federal Register notice of proposed rulemaking regarding test procedures for fluorescent lamp ballasts, as issued by the Deputy Assistant Secretary for Energy Efficiency on October 14, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

12

190 IEEE TRANSACTIONS ON PLASMA SCIENCE, VOL. 30, NO. 1, FEBRUARY 2002 Gap Closure in a Cold Metal Halide Lamp  

E-Print Network (OSTI)

lamp has been investigated using a two-dimensional, plasma transport model. Im- ages are presented- charge devices, lighting, plasma applications. METAL halide high-intensity-discharge (HID) lamps op- erate as high-pressure thermal arcs [1]. The cold fills of HID lamps are typically 50­100 torr of a rare

Kushner, Mark

13

New Energy Efficiency Standards for Metal Halide Lamp Fixtures to Save on Energy Bills and Reduce Carbon Pollution  

Office of Energy Efficiency and Renewable Energy (EERE)

As part of the Energy Departments efforts to develop efficiency standards that cut carbon pollution and save money by saving energy, U.S. Energy Secretary Ernest Moniz announced that the Department has finalized new energy efficiency standards for metal halide lamp fixtures.

14

Covered Product Category: Fluorescent Ballasts | Department of...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

can achieve large energy savings by moderating the timing and light output of lighting systems. Fluorescent lamp ballasts should have a ballast factor between 85% and 105% in...

15

Spatial and time-dependent distribution of plasma parameters in the metal-halide arc lamp  

E-Print Network (OSTI)

It was shown by several authors that closed high pressure arc a.c. discharge in mercury vapors with addition of metal halide cannot be described in frames of the local thermodynamic equilibrium (LTE) model. However some plasma parameters (electron and high lying excited states densities as well as Hg metastable levels densities) are assumed to be in equilibrium with electron temperature and these assumptions are applied in plasma diagnostics. To verify these supposition the method of local plasma spectroscopy based on spatial and temporal distribution of spectral line profiles was developed. The experimental set up is based on diffraction spectrometer with large aperture, spatial scanning device and photodetector, which allows to carry out the measurements in chosen phases of current period. The software for data acquisition and processing is based on LabVIEW system. The original method of joint data processing was applied to data arrays containing spatial, spectral and temporal distribution of a source surfa...

Khakhaev, A; Ekimov, K; Soloviev, A; Khakhaev, Anatoly; Luizova, Lidia; Ekimov, Konstantin; Soloviev, Alexey

2004-01-01T23:59:59.000Z

16

Medium Base Compact Fluorescent Lamps | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Templates for Reporting Test Results mediumbasecfltestreporttemplatev1.1.xlsx More Documents & Publications Fluorescent Lamp Ballasts Showerheads Beverage Vending Machines...

17

A SPICE Compatible Model of High Intensity Discharge Lamps  

E-Print Network (OSTI)

from the arc's * Corresponding author behavior of HID lamps. This model are derived from the arc-linear resistance of the lamp, is the global specific conductance of the plasma, V is the volume of the plasma, L is the length of plasma and S is the cross section. ~ Vin G1 Lamp Model Ballast v(lamp) i(lamp) Analytical

18

Compact fluorescent lamp using horizontal and vertical insulating septums and convective venting geometry  

DOE Patents (OSTI)

A novel design is described for a compact fluorescent lamp, including a lamp geometry which will increase light output and efficacy of the lamp in a base down operating position by providing horizontal and vertical insulating septums positioned in the ballast compartment of the lamp to provide a cooler coldspot. Selective convective venting provides additional cooling of the ballast compartment. 9 figs.

Siminovitch, M.

1998-02-10T23:59:59.000Z

19

The effects of supply harmonics on the performance of compact fluorescent lamps  

SciTech Connect

This paper describes a performance evaluation of ten compact fluorescent lighting systems operated with sinusoidal and distorted voltage waveform conditions. The lamps were either provided with an electronic ballast, a magnetic core ballast or a magnetic core ballast with a power factor correction circuit. The test results show that the electrical performance of the compact fluorescent lamps for both sinusoidal and distorted voltage waveform operation is related to the different types of ballast used. The cost of operation of these compact fluorescent lamps was calculated and compared to the cost of a conventional 60 W incandescent lamp.

Arseneau, R.; Ouellette, M.

1993-04-01T23:59:59.000Z

20

Optimized Magnetic Components Improve Efficiency of Compact Fluorescent Lamps  

E-Print Network (OSTI)

xtures (designed for incandescent bulbs) has allowed residential and small commercial electric customers of incandescent lamps and last 10 times longer [1]. High-frequency electronic ballasts are used to power CFLs

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Compact Fluorescent Plug-In Ballast-in-a-Socket  

SciTech Connect

The primary goal of this program was to develop a ballast system for plug-in CFLs (compact fluorescent lamps) that will directly replace standard metal shell, medium base incandescent lampholders (such as Levition No. 6098) for use with portable lamp fixtures, such as floor, table and desk lamps. A secondary goal was to identify a plug-in CFL that is optimized for use with this ballast. This Plug-in CFL Ballastin-a-Socket system will allow fixture manufacturers to easily manufacture CFL-based high-efficacy portable fixtures that provide residential and commercial consumers with attractive, cost-effective, and energy-efficient fixtures for use wherever portable incandescent fixtures are used today. The advantages of this proposed system over existing CFL solutions are that the fixtures can only be used with high-efficacy CFLs, and they will be more attractive and will have lower life-cycle costs than screw-in or adapter-based CFL retrofit solutions. These features should greatly increase the penetration of CFL's into the North American market. Our work has shown that using integrated circuits it is quite feasible to produce a lamp-fixture ballast of a size comparable to the current Edison-screw 3-way incandescent fixtures. As for price points for BIAS-based fixtures, end-users polled by the Lighting Research Institute at RPI indicated that they would pay as much as an additional $10 for a lamp containing such a ballast. The ballast has been optimized to run with a 26 W amalgam triple biax lamp in the base-down position, yet can accept non-amalgam versions of the lamp. With a few part alterations, the ballast can be produced to support 32 W lamps as well. The ballast uses GE's existing L-Comp[1] power topology in the circuit so that the integrated circuit design would be a design that could possibly be used by other CFL and EFL products with minor modifications. This gives added value by reducing cost and size of not only the BIAS, but also possibly other integral CFL and future dimmable integral and plug-in versions of the EFL products.

Rebecca Voelker

2001-12-21T23:59:59.000Z

22

Energy-efficient compact screw-in fluorescent lamp. Final report  

SciTech Connect

A compact fluorescent lamp has been designed and constructed which can replace an incandescent lamp. The lamp is slightly larger than a standard lamp (8 3/4 in. x 3 1/4 in.), but is designed to fit a majority of portable lamp applications. This version, with a core-coil ballast, results in a system efficacy of 54 lumens per watt, with a light output of more than 1800 lumens. This compares favorably with a 100-watt incandescent (17.5 lumens per watt and 1750 lumens light output). The color temperature of 3000/sup 0/K is compatible with an incandescent lamp (2800/sup 0/K). The color rendition index (CRI) is 84. With a solid-state ballast, the efficacy and light output could be increased by 20% (65 l/w, 2200 lumens) and could provide a direct replacement for a three-way, 150-watt incandescent lamp (15 l/w, 2200 lumens).

Morton, E.W.

1982-11-01T23:59:59.000Z

23

Ballasts: Handling, Storage and Procedure: 8.40 Created: 07/01/2009  

E-Print Network (OSTI)

of industrial compounds produced by chlorination of biphenyl, noted primarily as an environmental pollutant applies to all Contractors, Project Managers, Facilities Operations and Environmental Health & Safety (EH-lamping activities and construction/renovation activities at Columbia University. Ballasts manufactured before 1978

Jia, Songtao

24

Oregon Ballast Water Task Force Report on Ballast Water Management in Oregon  

E-Print Network (OSTI)

Oregon Ballast Water Task Force Report on Ballast Water Management in Oregon #12;Oregon Ballast Water Task Force Report on Ballast Water Management in Oregon Prepared for the Oregon State Legislature October 2006 #12;Report on Ballast Water Management in Oregon-2006 Acknowledgements We would like to thank

25

Retail Lamps Study 3.1: Dimming, Flicker, and Power Quality Characteristics of LED A Lamps.  

SciTech Connect

To date, all three reports in the retail lamps series have focused on basic performance parameters, such as lumen output, efficacy, and color quality. This report goes a step further, examining the photoelectric characteristics (i.e., dimming and flicker) of a subset of lamps from CALiPER Retails Lamps Study 3. Specifically, this report focuses on the dimming, power quality, and flicker characteristics of 14 LED A lamps, as controlled by four different retail-available dimmers. The results demonstrate notable variation across the various lamps, but little variation between the four dimmers. Overall, the LED lamps: ~tended to have higher relative light output compared to the incandescent and halogen benchmark at the same dimmer output signal (RMS voltage). The lamps dimming curves (i.e., the relationship between control signal and relative light output) ranged from linear to very similar to the square-law curve typical of an incandescent lamp. ~generally exhibited symmetrical behaviorthe same dimming curvewhen measured proceeding from maximum to minimum or minimum to maximum control signal. ~mostly dimmed below 10% of full light output, with some exceptions for specific lamp and dimmer combinations ~exhibited a range of flicker characteristics, with many comparing favorably to the level typical of a magnetically-ballasted fluorescent lamp through at least a majority of the dimming range. ~ always exceeded the relative (normalized) efficacy over the dimming range of the benchmark lamps, which rapidly decline in efficacy when they are dimmed. This report generally does not attempt to rank the performance of one product compared to another, but instead focuses on the collective performance of the group versus conventional incandescent or halogen lamps, the performance of which is likely to be the baseline for a majority of consumers. Undoubtedly, some LED lamps perform betteror more similar to conventional lampsthan others. Some perform desirably for one characteristic, but not others. Consumers (and specifiers) may have a hard time distinguishing better-performing lamps from one another; at this time, physical experimentation is likely the best evaluation tool.

Royer, Michael P.; Poplawski, Michael E.; Brown, Charles C.

2014-12-14T23:59:59.000Z

26

Lamp Divisions  

Office of Legacy Management (LM)

--- --- /A;; i :' r%i;in~house ilEc;' i:Z3:~cra:ion Lamp Divisions , _.. (I +i. 0 :,,,rg. . I . . -= i?e p/q! qe)-' &se pw E.rcale?l iev, Je!sey 07m March 20, 1 gs? ::r . J. A. Jones I ti. 5. Muclear Regulatory Commission .> = ..- haterials Licensing Branch -s - ,.I, - - Division of Fuel Cycle and hateri al Safety LY. , $2 - _ . ' -' . 3 _- - Yeshington, C. C. 2@555 - :_ :--, =-- -- .-?J -.: y...., : :- 7 Dear Mr. Jones : y-- --, ? . *I 2=15 2 r; X -P The following is our final report of the decontamination efZor?s takz in our Bui Iding 7 basement and wi 11 also serve to update our report i& November 12, 1980. As stated in NRC' s report of December 22, 1983, two closeout inspect ions were conducted by your King of Prussia off i ce on November 21 and December 2,

27

Fully Integrated Ballast Controller with  

E-Print Network (OSTI)

Global Research (through CoPEC) and the Department of Energy's National Energy Technology Laboratory. Simplified block diagram of the two primary control loops in the ballast IC: (I) inner phase control and (2

28

Uncertainty and sensitivity analyses of ballast life-cycle cost and payback period  

SciTech Connect

The paper introduces an innovative methodology for evaluating the relative significance of energy-efficient technologies applied to fluorescent lamp ballasts. The method involves replacing the point estimates of life cycle cost of the ballasts with uncertainty distributions reflecting the whole spectrum of possible costs, and the assessed probability associated with each value. The results of uncertainty and sensitivity analyses will help analysts reduce effort in data collection and carry on analysis more efficiently. These methods also enable policy makers to gain an insightful understanding of which efficient technology alternatives benefit or cost what fraction of consumers, given the explicit assumptions of the analysis.

McMahon, James E.; Liu, Xiaomin; Turiel, Ike; Hakim, Sajid; Fisher, Diane

2000-06-01T23:59:59.000Z

29

Lumen and Chromaticity Maintenance of LED PAR38 Lamps Operated in Steady-State Conditions  

SciTech Connect

The lumen depreciation and color shift of 38 different lamps (32 LED, 2 CFL, 1 ceramic metal halide [CMH], 3 halogen) were monitored in a specially developed automated long-term test apparatus (ALTA2) for nearly 14,000 hours. Five samples of each lamp model were tested, with measurements recorded on a weekly basis. The lamps were operated continuously at a target ambient temperature between 44C and 45C.

Royer, Michael P.

2014-12-01T23:59:59.000Z

30

Effective Ship Ballast Water Treatment System Management  

Science Journals Connector (OSTI)

Besides its great effect on ship stability, ballast water causes an important problem. While a ship loads ballast water from any sea, it ... species. These species may have a great effect on the local ecological ...

Levent Bilgili; Kaan nlgeno?lu

2013-01-01T23:59:59.000Z

31

Covered Product Category: Fluorescent Ballasts  

Energy.gov (U.S. Department of Energy (DOE))

FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including fluorescent ballasts, which are a FEMP-designated product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

32

Turning on LAMP  

ScienceCinema (OSTI)

Christoph Bostedt, a senior staff scientist at SLAC's Linac Coherent Light Source X-ray laser, provides a sneak peek of a powerful new instrument, called LAMP, that is now available for experiments that probe the atomic and molecular realm. LAMP replaces and updates the first instrument at LCLS, dubbed CAMP, which will be installed at an X-ray laser in Germany.

Bostedt, Christoph

2014-07-16T23:59:59.000Z

33

Turning on LAMP  

SciTech Connect

Christoph Bostedt, a senior staff scientist at SLAC's Linac Coherent Light Source X-ray laser, provides a sneak peek of a powerful new instrument, called LAMP, that is now available for experiments that probe the atomic and molecular realm. LAMP replaces and updates the first instrument at LCLS, dubbed CAMP, which will be installed at an X-ray laser in Germany.

Bostedt, Christoph

2014-06-30T23:59:59.000Z

34

Fluorescent Tube Lamps  

Energy.gov (U.S. Department of Energy (DOE))

FEMP temporarily suspended its energy efficiency requirements for fluorescent tube lamps as it evaluates the market impact of the pending 2012 minimum efficiency standards for fluorescent lamps. The program will issue updated energy efficiency requirements when the market distribution of this product category stabilizes and when doing so has the potential to result in significant Federal energy savings.

35

Energy saving in lighting system with fuzzy logic controller which uses light-pipe and dimmable ballast  

Science Journals Connector (OSTI)

Approximately, 20% of the electricity consumed in the world is spent for lighting. More efficient utilization of the sun, as a natural source of light, for lighting would save electricity used for lighting. The aim of this study is to illuminate a windowless room via a light-pipe and dimmable electronic ballasts. Light-pipe is used for the illumination of the space during the daytime. In case of inadequate daylight, artificial lighting is made via dimmable electronic ballasts and fluorescence lamps. Artificial lighting is supervised by a fuzzy logic control system to keep the illumination level at 350lux. When there is a motion in the room, the system works with the message of the motion sensor, which, thereby, enables energy saving. Additionally, dimming the lamps result in conversation of the electrical energy used for illumination. After the experimental studies, 350lux value targeted in the work plane is achieved with 10lux error.

Serta Grgl; Nazmi Ekren

2013-01-01T23:59:59.000Z

36

Report on the Oregon Ballast Water Management Program in 2004  

E-Print Network (OSTI)

Report on the Oregon Ballast Water Management Program in 2004 #12;Acknowledgements We would like Ballast Water Management Program in 2004 Produced for the Oregon State Legislature By The Oregon Ballast State University September 2004 #12;Report on Oregon Ballast Water Management Program 2004 Executive

37

Magnetic fluorescent lamp  

DOE Patents (OSTI)

The radiant emission of a mercury-argon discharge in a fluorescent lamp assembly is enhanced by providing means for establishing a magnetic field with lines of force along the path of electron flow through the bulb of the lamp assembly, to provide Zeeman splitting of the ultraviolet spectral line. Optimum results are obtained when the magnetic field strength causes a Zeeman splitting of approximately 1.7 times the thermal line width.

Berman, S.M.; Richardson R.W.

1983-12-29T23:59:59.000Z

38

EFFECT OF COAL DUST ONEFFECT OF COAL DUST ON RAILROAD BALLAST STRENGTHRAILROAD BALLAST STRENGTH  

E-Print Network (OSTI)

1 EFFECT OF COAL DUST ONEFFECT OF COAL DUST ON RAILROAD BALLAST STRENGTHRAILROAD BALLAST STRENGTH for Laboratory StudyFouling Mechanism / Need for Laboratory Study Mechanical Properties of Coal DustMechanical Properties of Coal Dust Grain Size AnalysisGrain Size Analysis AtterbergAtterberg LimitsLimits Specific

Barkan, Christopher P.L.

39

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Metal Halide Lamp Fixtures Metal Halide Lamp Fixtures Sign up for e-mail updates on regulations for this and other products The Department of Energy (DOE) has regulated the energy efficiency level of metal halide lamp fixtures since 2007. A metal halide lamp fixture uses a metal halide lamp and a metal halide lamp ballast. The lamp is the light source and the ballast starts and regulates current. Metal halide fixtures or lighting systems provide lighting for parking lots and streets, flood lighting, athletics facilities, big-box stores, and warehouses. The current standards will save approximately 6.4 quads of energy and result in approximately $9.6 billion in energy bill savings for products shipped from 2009-2038. The standard will avoid about 93.6 million metric tons of carbon dioxide emissions.

40

Energy-efficient incandescent lamp: Final report  

E-Print Network (OSTI)

of Energy Conserving Incandescent Lamps", J . Brett, R.July 1981. "Filaments for Incandescent Lamps with Radiation20-22 "Energy Saving Incandescent Lamps with Infrared

Verderber, R.

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

SunShot Initiative: Innovative Ballasted Flat Roof Solar Photovoltaic  

NLE Websites -- All DOE Office Websites (Extended Search)

Innovative Ballasted Flat Roof Innovative Ballasted Flat Roof Solar Photovoltaic Racking System to someone by E-mail Share SunShot Initiative: Innovative Ballasted Flat Roof Solar Photovoltaic Racking System on Facebook Tweet about SunShot Initiative: Innovative Ballasted Flat Roof Solar Photovoltaic Racking System on Twitter Bookmark SunShot Initiative: Innovative Ballasted Flat Roof Solar Photovoltaic Racking System on Google Bookmark SunShot Initiative: Innovative Ballasted Flat Roof Solar Photovoltaic Racking System on Delicious Rank SunShot Initiative: Innovative Ballasted Flat Roof Solar Photovoltaic Racking System on Digg Find More places to share SunShot Initiative: Innovative Ballasted Flat Roof Solar Photovoltaic Racking System on AddThis.com... Concentrating Solar Power Photovoltaics

42

Retail Replacement Lamps  

Energy.gov (U.S. Department of Energy (DOE))

Annual CALiPER testing of A19, G25, candelabra, night light, MR16/PAR16, PAR20, and PAR30 replacement lamps purchased directly from store shelves offers insights on performance trends from year to year. The report findings offer valuable insights for manufacturers and retailers alike.

43

LED MR16 Lamps  

Energy.gov (U.S. Department of Energy (DOE))

The following CALiPER report provides detailed analysis of LED MR16 lamp performance, covering basic performance characteristics as well as subjective evaluation of beam, shadow, and color quality. Pending reports will offer analysis on performance attributes that are not captured by LM-79 testing. These reports are intended to educate the industry on market trends, potential issues, and important areas for improvement.

44

Report on the Oregon Ballast Water Management Program  

E-Print Network (OSTI)

Report on the Oregon Ballast Water Management Program in 2002 #12;Report on the Oregon Ballast Water Management Program in 2002 Produced for the Oregon State Legislature by Jordan Vinograd and Mark Water Task Force December 2002 #12;Report on Oregon Ballast Water Management Program in 2002 i Executive

45

LED PAR38 Lamps  

Energy.gov (U.S. Department of Energy (DOE))

The following CALiPER reports provide detailed analysis of LED PAR38 lamp performance, covering basic performance characteristics as well as subjective evaluation of beam, shadow, and color quality. Pending reports will offer analysis on flicker, dimming and power quality characteristics; stress testing; and lumen and chromaticity maintenance. These reports are intended to educate the industry on market trends, potential issues, and important areas for improvement.

46

Lighting Group: Sources and Ballasts: HID Lighting Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Ballasts and Controls for HID Lighting Ballasts and Controls for HID Lighting Systems Evaluation of Electronic Ballasts and Related Controls for HID Lighting Systems Objective HID ballast The goal of this project is to evaluate the potential of electronic ballasts and related controls for HID lighting systems to improve the efficiency of current technology. The specific objectives of this project are to: Test, analyze and determine the potential of electronic ballasts for HID lighting systems in cooperation with manufacturers as an emerging energy efficient technology to reduce lighting loads in commercial, industrial and municipal applications. Identify control strategies to further improve the energy efficiency of these systems with a municipal partner. Provide appropriate recommendations for incorporating these technologies into current state codes and regulations.

47

Actinide halide complexes  

SciTech Connect

A compound of the formula MX{sub n}L{sub m} wherein M = Th, Pu, Np,or Am thorium, X = a halide atom, n = 3 or 4, L is a coordinating ligand selected from the group consisting of aprotic Lewis bases having an oxygen-, nitrogen-, sulfur-, or phosphorus-donor, and m is 3 or 4 for monodentate ligands or is 2 for bidentate ligands, where n + m = 7 or 8 for monodentate ligands or 5 or 6 for bidentate ligands, a compound of the formula MX{sub n} wherein M, X, and n are as previously defined, and a process of preparing such actinide metal compounds including admixing the actinide metal in an aprotic Lewis base as a coordinating solvent in the presence of a halogen-containing oxidant, are provided.

Avens, L.R.; Zwick, B.D.; Sattelberger, A.P.; Clark, D.L.; Watkin, J.G.

1991-02-07T23:59:59.000Z

48

Max Tech and Beyond: Fluorescent Lamps  

E-Print Network (OSTI)

Fluorescent Lamps and Incandescent Reflector Lamps; Finalmany end- use applications. Incandescent Outdoor Stationaryof color compared with the incandescent reference source is

Scholand, Michael

2012-01-01T23:59:59.000Z

49

Custom Spectral Shaping for EMI Reduction in Electronic Ballasts  

E-Print Network (OSTI)

modulating waveforms, for custom spectral shaping of the fundamental harmonic of electronic ballastsCustom Spectral Shaping for EMI Reduction in Electronic Ballasts Sandra Johnson, Yan Yin, Regan Zane Colorado Power Electronics Center University of Colorado at Boulder Boulder, Colorado 80309

50

Actinide halide complexes  

DOE Patents (OSTI)

A compound is described of the formula MX[sub n]L[sub m] wherein M is a metal atom selected from the group consisting of thorium, plutonium, neptunium or americium, X is a halide atom, n is an integer selected from the group of three or four, L is a coordinating ligand selected from the group consisting of aprotic Lewis bases having an oxygen-, nitrogen-, sulfur-, or phosphorus-donor, and m is an integer selected from the group of three or four for monodentate ligands or is the integer two for bidentate ligands, where the sum of n+m equals seven or eight for monodentate ligands or five or six for bidentate ligands. A compound of the formula MX[sub n] wherein M, X, and n are as previously defined, and a process of preparing such actinide metal compounds are described including admixing the actinide metal in an aprotic Lewis base as a coordinating solvent in the presence of a halogen-containing oxidant.

Avens, L.R.; Zwick, B.D.; Sattelberger, A.P.; Clark, D.L.; Watkin, J.G.

1992-11-24T23:59:59.000Z

51

Computational Modeling of Ballast Tanks to Improve Understanding and Maximize Effectiveness of Management Practices and Treatment  

E-Print Network (OSTI)

Computational Modeling of Ballast Tanks to Improve Understanding and Maximize Effectiveness tanks exchange coastal ballast water with mid-ocean seawater (referred to as "ballast water exchange of high-resolution computational fluid dynamics (CFD) to model ballast tank water flow and to predict EE

52

Preparation of cerium halide solvate complexes  

DOE Patents (OSTI)

Crystals of a solvated cerium(III) halide solvate complex resulted from a process of forming a paste of a cerium(III) halide in an ionic liquid, adding a solvent to the paste, removing any undissolved solid, and then cooling the liquid phase. Diffusing a solvent vapor into the liquid phase also resulted in crystals of a solvated cerium(III) halide complex.

Vasudevan, Kalyan V; Smith, Nickolaus A; Gordon, John C; McKigney, Edward A; Muenchaussen, Ross E

2013-08-06T23:59:59.000Z

53

Replacing Incandescent Lightbulbs and Ballasts | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Incandescent Lightbulbs and Ballasts Incandescent Lightbulbs and Ballasts Replacing Incandescent Lightbulbs and Ballasts July 29, 2012 - 5:16pm Addthis Many incandescent lightbulbs can be replaced with more energy efficient options. | Photo courtesy of ©iStockphoto.com/ClarkandCompany. Many incandescent lightbulbs can be replaced with more energy efficient options. | Photo courtesy of ©iStockphoto.com/ClarkandCompany. What does this mean for me? For the greatest energy efficiency, use new fixtures with new lightbulbs. Replace A-type lightbulbs with more energy-efficient options such as CFLs, LEDs, and energy-saving (halogen) incandescents. Matching replacement lightbulbs to existing fixtures and ballasts can be tricky, especially with older fixtures. Using new fixtures made for new lightbulbs gives you the greatest energy savings, reliability, and

54

Replacing Incandescent Lightbulbs and Ballasts | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Replacing Incandescent Lightbulbs and Ballasts Replacing Incandescent Lightbulbs and Ballasts Replacing Incandescent Lightbulbs and Ballasts July 29, 2012 - 5:16pm Addthis Many incandescent lightbulbs can be replaced with more energy efficient options. | Photo courtesy of ©iStockphoto.com/ClarkandCompany. Many incandescent lightbulbs can be replaced with more energy efficient options. | Photo courtesy of ©iStockphoto.com/ClarkandCompany. What does this mean for me? For the greatest energy efficiency, use new fixtures with new lightbulbs. Replace A-type lightbulbs with more energy-efficient options such as CFLs, LEDs, and energy-saving (halogen) incandescents. Matching replacement lightbulbs to existing fixtures and ballasts can be tricky, especially with older fixtures. Using new fixtures made for new

55

Performance of Geogrid Reinforced Ballast under Dynamic Loading  

E-Print Network (OSTI)

Railroad ballast consists of open graded crushed stone used as a bed for railroad track to provide stability. It plays a significant role in providing support for the track base and distributing the load to the weaker ...

Jowkar, Milad

2011-12-31T23:59:59.000Z

56

Energy Cost Calculator for Compact Fluorescent Lamps | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

project. Modify the default values to suit your project requirements. Existing incandescent lamp wattage Watts Incandescent lamp cost dollars Incandescent lamp life 1000 hours...

57

Health Implications of New Lamp Technology Progress with Lamp Safety  

E-Print Network (OSTI)

: ­ ACGIH Threshold Limit Values, UV, lasers, etc. ­ ANSI Z136.1 for lasers with MPEs 0.1 ps -30 ks ­ ANSI RP 27.1 to ANSI RP 27.3 Lamp Safety · Internationally: ­ International Commission on Non

California at Davis, University of

58

Disinfection of Ballast Water with Iron Activated Persulfate  

Science Journals Connector (OSTI)

The lack of harmful byproducts produced during application makes PS an attractive alternative to other biocides currently in use for ballast water treatments and merits further testing at a larger scale. ... Waldemer, R. H.; Tratnyek, P. G.; Johnson, R. L.; Nurmi, J. T.Oxidation of chlorinated ethenes by heat-activated persulfate: kinetics and products Environ. ... Here, the authors examine the efficacy of the ballast water biocides SeaKleen and Peraclean Ocean, and the chlorine dioxide biocide Vibrex. ...

Samyoung Ahn; Tawnya D. Peterson; Jason Righter; Danielle M. Miles; Paul G. Tratnyek

2013-09-11T23:59:59.000Z

59

Capacitive sensing with a fluorescent lamp  

E-Print Network (OSTI)

This work presents a modified fluorescent lamp that can be used as a capacitive sensing system. The lamp sensor measures changes in the electric fields emitted from the fluorescent bulbs in order to deduce the presence and ...

Cooley, John Jacob

2007-01-01T23:59:59.000Z

60

Impending U.S. lighting standards will boost market for halogen-infrared lamps: New product line expanding  

SciTech Connect

Many of the incandescent floodlights and spotlights manufactured today will not meet lighting efficiency standards taking effect in the US in 1995. As these models cease production, demand will grow for higher efficiency units to fill this huge market, which now totals about 100 million lamps per year. One prime contender is a new class of halogen lamps that use a spectrally selective coating to reflect heat back onto the filament, reducing the amount of electricity needed to generate light. GE Lighting`s Halogen-IR line is the only series of such lamps currently available to replace the conventional floodlights and spotlights that will be banned by the new standards. Other manufacturers may adopt the technology, however, and the Japanese producer Ushio already sells in the US a line of smaller halogen lamps with a similar heat-reflective coating. In terms of efficacy and lifetime, Halogen-IR lamps out perform standard incandescents and standard halogens, but fall far short of fluorescent, metal halide, and high-pressure sodium sources. These other lighting systems are more appropriate and cost-effective than incandescents for many ambient lighting applications. For accent lighting and other tasks that are best suited to incandescent lighting, however, the Halogen-IR lamp is often a superior choice.

Sardinsky, R.; Shepard, M.

1993-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Lightweight, self-ballasting photovoltaic roofing assembly  

DOE Patents (OSTI)

A photovoltaic roofing assembly comprises a roofing membrane (102), a plurality of photovoltaic modules (104, 106, 108) disposed as a layer on top of the roofing membrane (102), and a plurality of pre-formed spacers, pedestals or supports (112, 114, 116, 118, 120, 122) which are respectively disposed below the plurality of photovoltaic modules (104, 106, 108) and integral therewith, or fixed thereto. Spacers (112, 114, 116, 118, 120, 122) are disposed on top of roofing membrane (102). Membrane (102) is supported on conventional roof framing, and attached thereto by conventional methods. In an alternative embodiment, the roofing assembly may have insulation block (322) below the spacers (314, 314', 315, 315'). The geometry of the preformed spacers (112, 114, 116, 118, 120, 122, 314, 314', 315, 315') is such that wind tunnel testing has shown its maximum effectiveness in reducing net forces of wind uplift on the overall assembly. Such construction results in a simple, lightweight, self-ballasting, readily assembled roofing assembly which resists the forces of wind uplift using no roofing penetrations.

Dinwoodie, Thomas L. (Berkeley, CA)

1998-01-01T23:59:59.000Z

62

Lightweight, self-ballasting photovoltaic roofing assembly  

DOE Patents (OSTI)

A photovoltaic roofing assembly comprises a roofing membrane (102), a plurality of photovoltaic modules (104, 106, 108) disposed as a layer on top of the roofing membrane (102), and a plurality of pre-formed spacers, pedestals or supports (112, 114, 116, 118, 120, 122) which are respectively disposed below the plurality of photovoltaic modules (104, 106, 108) and integral therewith, or fixed thereto. Spacers (112, 114, 116, 118, 120, 122) are disposed on top of roofing membrane (102). Membrane (102) is supported on conventional roof framing, and attached thereto by conventional methods. In an alternative embodiment, the roofing assembly may have insulation block (322) below the spacers (314, 314', 315, 315'). The geometry of the preformed spacers (112, 114, 116, 118, 120, 122, 314, 314', 315, 315') is such that wind tunnel testing has shown its maximum effectiveness in reducing net forces of wind uplift on the overall assembly. Such construction results in a simple, lightweight, self-ballasting, readily assembled roofing assembly which resists the forces of wind uplift using no roofing penetrations.

Dinwoodie, T.L.

1998-05-05T23:59:59.000Z

63

LED Linear Lamps and Troffer Lighting  

Energy.gov (U.S. Department of Energy (DOE))

The CALiPER program performed a series of investigations on linear LED lamps. Each report in the series covers the performance of up to 31 linear LED lamps, which were purchased in late 2012 or 2013. The first report focuses on bare lamp performance of LED T8 replacement lamps and subsequent reports examine performance in various troffers, as well as cost-effectiveness. There is also a concise guidance document that describes the findings of the Series 21 studies and provides practical advice to manufacturers, specifiers, and consumers (Report 21.4: Summary of Linear (T8) LED Lamp Testing , 5 pages, June 2014).

64

Lanthanide doped strontium barium mixed halide scintillators  

DOE Patents (OSTI)

The present invention provides for a composition comprising an inorganic scintillator comprising a lanthanide-doped strontium barium mixed halide useful for detecting nuclear material.

Gundiah, Gautam; Bizarri, Gregory; Hanrahan, Stephen M; Bourret-Courchesne, Edith; Derenzo, Stephen E

2013-07-16T23:59:59.000Z

65

Max Tech and Beyond: Fluorescent Lamps  

E-Print Network (OSTI)

varies by watts of power per foot of electrical arc in theFoot Linear Fluorescent Lamps Efficacy Life Lumens Type Base Power

Scholand, Michael

2012-01-01T23:59:59.000Z

66

Covered Product Category: Compact Fluorescent Lamps  

Energy.gov (U.S. Department of Energy (DOE))

FEMP provides acquisition guidance across a variety of product categories, including compact fluorescent lamps (CFLs), which are an ENERGY STAR-qualified product category.

67

Energy saving controller for fluorescent lamps.  

E-Print Network (OSTI)

??Although fluorescent lamp is a very efficient lighting device in daily life, still the high harmonic distortion and low power factor cause unnecessary energy consumption. (more)

Cheong, Zhi Xiong

2010-01-01T23:59:59.000Z

68

LED Replacements for Linear Fluorescent Lamps Webcast  

Energy.gov (U.S. Department of Energy (DOE))

In this June 20, 2011 webcast on LED products marketed as replacements for linear fluorescent lamps, Jason Tuenge of the Pacific Northwest National Laboratory (PNNL) discussed current Lighting...

69

Energy conservation treatment in Exxon's the lamp  

Science Journals Connector (OSTI)

In this article, Mary Ann Ferguson-DeThorne examines The Lamp, a publication sponsored by Exxon, to determine when and to what extent Exxon informed The Lamp's audience about an impending energy shortage and possible energy conservation methods, to learn if The Lamp's energy conservation messages reflected Exxon's stated conservation positions, and to compare The Lamp to mass-circulation news magazines in terms of how well it alerted its audience to the impending energy shortage. The crucial period of study here is 19711973; prior to the Arab oil boycott and the 1974 Congressional investigation of charges that the large oil companies had contrived shortages to eliminate competition.

Mary Ann Ferguson-DeThorne

1978-01-01T23:59:59.000Z

70

General Service LED Lamps | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

DOE SSL technology fact sheet that compares general service LED light bulbs with incandescent and CFL bulbs. ledgeneral-service-lamps.pdf More Documents & Publications LED...

71

Biomass-Derived Hydrogen from a Thermally Ballasted Gasifier  

E-Print Network (OSTI)

Biomass-Derived Hydrogen from a Thermally Ballasted Gasifier DOE Hydrogen Program Contractors biomass #12;Approach Outline Gasifier Pilot Plant· Develop subsystems for the hydrogen production system and pyrolysis occur simultaneously in a single reactor · Exothermic combustion provides heat · Endothermic

72

General service incandescent lamp with improved efficiency  

SciTech Connect

A high efficiency general service incandescent lamp is disclosed. The disclosed improved general service incandescent lamp has an outer and an inner envelope. The inner envelope has a relatively small housing containing a halogen gas and a relatively high pressure efficient fill-gas and in which a low voltage filament is spatially disposed therein.

Berlec, I.

1985-06-18T23:59:59.000Z

73

Portable lamp with dynamically controlled lighting distribution  

DOE Patents (OSTI)

A double lamp table or floor lamp lighting system has a pair of compact fluorescent lamps (CFLs) arranged vertically with a reflective septum in between. By selectively turning on one or both of the CFLs, down lighting, up lighting, or both up and down lighting is produced. The control system can also vary the light intensity from each CFL. The reflective septum insures that almost all the light produced by each lamp will be directed into the desired light distribution pattern which is selected and easily changed by the user. Planar compact fluorescent lamps, e.g. circular CFLs, particularly oriented horizontally, are preferable. CFLs provide energy efficiency. The lighting system may be designed for the home, hospitality, office or other environments.

Siminovitch, Michael J. (Pinole, CA); Page, Erik R. (Berkeley, CA)

2001-01-01T23:59:59.000Z

74

LED T8 Replacement Lamps | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

T8 Replacement Lamps LED T8 Replacement Lamps This documents provides an overview of LED T8 replacement lamps and helps define a reasonable minimum performance level for the...

75

Solid-state lamp with integral occupancy sensor  

E-Print Network (OSTI)

Previous work demonstrated a retrofit proximity detector for fluorescent lamps using the lamp's own stray electric fields. This paper extends the retrofit sensor system to a solid-state (LED) lamp. The design and implementation ...

Cooley, John J.

76

COST EFFECTIVENESS OF LONG LIFE INCANDESCENT LAMPS AND ENERGY BUTTONS  

E-Print Network (OSTI)

as any 1ong-li incandescent lamp or system evaluated in thisEFFECTIVENESS OF LONG LIFE INCANDESCENT LAMPS AND ENERGYEFFECTIVENESS OF LONG LIFE INCANDESCENT LAMPS AND ENERGY

Verderber, Rudy

2013-01-01T23:59:59.000Z

77

DuraLamp USA: Order (2010-CE-0912)  

Energy.gov (U.S. Department of Energy (DOE))

DOE ordered DuraLamp USA, Inc. to pay a $2,500 civil penalty after finding DuraLamp USA had failed to certify that model PAR 30, an incandescent reflector lamp, complies with the applicable energy conservation standards.

78

Tungsten wire for incandescent lamps  

SciTech Connect

Tungsten wire for incandescent lamp filaments must operate at high temperatures and for long times. To meet these requirements, the grain morphology of the wire must be controlled to reduce the propensity for grain boundary sliding. The morphology is a function of the distribution of very small pockets of potassium in the wire and the mechanical processing from ingot to wire. The behavior of the filament is directly related to the grain morphology. This paper describes the mechanism by which the potassium is incorporated into and distributed in the ingot. The elongation and spheroidization of the bubbles during hot rolling and swaging is also examined and related to the grain morphology of wire. Some indications of the relationship between grain morphology and filament behavior are also given.

Walter, J.L.; Briant, C.L. (General Electric Corporate Research and Development, Schenectady, NY (USA))

1990-09-01T23:59:59.000Z

79

Power factor and harmonic distortion characteristics of energy efficient lamps  

SciTech Connect

This paper evaluates the performance of a new class of lamps which are generally classified as the energy-saving lamps. It is shown that, when compared with the incandescent lamps, these lamps indeed consume less real power and have higher relative illumination. However, the energy-saving lamps operate at a low power factor and produce current distortion which are much higher than the distortion produced by the traditional incandescent lamps.

Etezadi-Amoli, M.; Florence, T.

1989-07-01T23:59:59.000Z

80

Cost effectiveness of long life incandescent lamps and energy buttons  

SciTech Connect

Long-life replacement lamps for the incandescent lamp have been evaluated with regard to their cost effectiveness. The replacements include the use of energy buttons that extend lamp life as well as an adaptive fluorescent circline lamp that will fit into existing incandescent lamp sockets. The initial, operating, and replacement costs for one million lumen hours are determined for each lamp system. It is found that the most important component lighting cost is the operating cost. Using lamps that are less efficient or devices that cause lamps to operate less efficiently are not cost-effective. The adaptive fluorescent circline lamp, even at an initial unit cost of $20.00, is the most cost-effective source of illumination compared to the incandescent lamp and lamp systems examined.

Verderber, R.; Morse, O.

1980-04-07T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Lamp system for uniform semiconductor wafer heating  

DOE Patents (OSTI)

A lamp system with a very soft high-intensity output is provided over a large area by water cooling a long-arc lamp inside a diffuse reflector of polytetrafluorethylene (PTFE) and titanium dioxide (TiO.sub.2) white pigment. The water is kept clean and pure by a one micron particulate filter and an activated charcoal/ultraviolet irradiation system that circulates and de-ionizes and biologically sterilizes the coolant water at all times, even when the long-arc lamp is off.

Zapata, Luis E. (Livermore, CA); Hackel, Lloyd (Livermore, CA)

2001-01-01T23:59:59.000Z

82

Compact fluorescent lamp applications in luxury hotels  

SciTech Connect

Over the past several years, consumers, lighting designers, and energy conservationists have paid increasing attention to the special characteristics of compact fluorescent lamps (CFLs). CFLs can typically be used to replace incandescent lamps of three to four times their own wattage, and their color rendering indices (CRIs)-80 to 85-make them virtually indistinguishable from incandescents. The typical 10,0000-hour life of a CFL often makes savings in labor its most desirable feature when compared to a shorter-lived incandescent lamp.

Gilleskie, R.J.

1996-01-01T23:59:59.000Z

83

Utility DSM Rebates for electronic ballasts: National estimates and market impact (1992 - 1997)  

E-Print Network (OSTI)

1 GENERAL DEVELOPMENTS IN DSM AND ENERGY EFFICIENCYFigure 1. Ballast Shipment and DSM Rebate Data . . . . .utility Demand-Side Management (DSM) rebates for electronic

Busch, C.B.; Atkinson, B.A.; Eto, J.H.; Turiel, I.; McMahon, J.E.

2000-01-01T23:59:59.000Z

84

LED lamp power management system and method  

DOE Patents (OSTI)

An LED lamp power management system and method including an LED lamp having an LED controller 58; a plurality of LED channels 60 operably connected to the LED controller 58, each of the plurality of LED channels 60 having a channel switch 62 in series with at least one shunted LED circuit 83, the shunted LED circuit 83 having a shunt switch 68 in parallel with an LED source 80. The LED controller 58 reduces power loss in one of the channel switch 62 and the shunt switch 68 when LED lamp electronics power loss (P.sub.loss) exceeds an LED lamp electronics power loss limit (P.sub.lim); and each of the channel switches 62 receives a channel switch control signal 63 from the LED controller 58 and each of the shunt switches 68 receives a shunt switch control signal 69 from the LED controller 58.

Gaines, James; Clauberg, Bernd; Van Erp, Josephus A. M.

2013-03-19T23:59:59.000Z

85

MagLab - Arc Lamp Tutorial  

NLE Websites -- All DOE Office Websites (Extended Search)

with 2,000 cells to create an arc across a 4-inch (100 millimeter) gap. When suitable electric generators became available in the late 1870s, the practical use of arc lamps began....

86

CALiPER Retail Lamps Study 3  

SciTech Connect

The CALiPER program first began investigating LED lamps sold at retail stores in 2010, purchasing 33 products from eight retailers and covering six product categories. The findings revealed a fragmented marketplace, with large disparities in performance of different products, accuracy of manufacturer claims, and offerings from different retail outlets. Although there were some good products, looking back many would not be considered viable competitors to other available options, with too little lumen output, not high enough efficacy, or poor color quality. CALiPER took another look in late 2011purchasing 38 products of five different types from nine retailers and the improvement was marked. Performance was up; retailer claims were more accurate; and the price per lumen and price per unit efficacy were down, although the price per product had not changed much. Nonetheless, there was still plenty of room for improvement, with the performance of LED lamps not yet reaching that of well-established classes of conventional lamps (e.g., 75 W incandescent A19 lamps). Since the second retail lamp study was published in early 2012, there has been substantial progress in all aspects of LED lamps available from retailers. To document this progress, CALiPER again purchased a sample of lamps from retail stores 46 products in total, focusing on A19, PAR30, and MR16 lamps but instead of a random sample, sought to select products to answer specific hypotheses about performance. These hypotheses focused on expanding ranges of LED equivalency, the accuracy of lifetime claims, efficacy and price trends, as well as changes to product designs. Among other results, key findings include: There are now very good LED options to compete with 60 W, 75 W, and 100 W incandescent A19 lamps, and 75 W halogen PAR30 lamps. MR16 lamps have shown less progress, but there are now acceptable alternatives to 35 W, 12 V halogen MR16 lamps and 50 W, 120 V halogen MR16 lamps for some applications. Other uses, such as in enclosed luminaires, may require more development. At the same price point, lamps purchased in 2013 tended to have higher output and slightly higher efficacy than in 2011 or 2010. Over 30% of the products purchased in 2013 exceeded the maximum efficacy measured in 2011 (71 lm/W), with the most efficacious product measured at 105 lm/W. There appears to be increasing consistency in color quality, with a vast majority of products having a CCT of 2700 K or 3000 K and a CRI between 80 and 85. There were also fewer poor performing products tested and more high-performing products available in 2013 than in previous years. The accuracy of equivalency and performance claims was better than in 2011, but remains a concern, with 43% of tested products failing to completely meet their equivalency claim and 20% of products failing to match the manufacturers performance data. Although progress has been substantial, on average LED lamps remain more expensive than other energy efficiency lighting technologies -- although some aspects can be superior. Although not universal to all product lines or all product types, the issue of insufficient lumen output from LED lamps is waning. Thus, manufacturers can focus on other issues, such as reducing cost, improving electrical/dimmer compatibility, eliminating flicker, or improving color quality. While these issues are not inherent to all products, they remain a concern for the broader market.

Royer, Michael P.; Beeson, Tracy A.

2014-02-01T23:59:59.000Z

87

PHASE I FINAL REPORT SUBCONTRACT NO. 2019702 "ENERGY EFFICIENT FLUORESCENT BALLASTS"  

E-Print Network (OSTI)

RELATIVE EFFICIENCY (FOOT CANDLES/POWER IN) LAMP TEMPERATUREEFFICIENCY (FOOT CANDLES/POWER IN) LAMP TEMPERATURE *INPUT CURRENT POWER INPUT POWER FACTOR LIGHT IN FOOT CANDLES

Authors, Various

2011-01-01T23:59:59.000Z

88

Building Technologies Office: Fluorescent and Incandescent Lamps Public  

NLE Websites -- All DOE Office Websites (Extended Search)

Fluorescent and Fluorescent and Incandescent Lamps Public Meeting to someone by E-mail Share Building Technologies Office: Fluorescent and Incandescent Lamps Public Meeting on Facebook Tweet about Building Technologies Office: Fluorescent and Incandescent Lamps Public Meeting on Twitter Bookmark Building Technologies Office: Fluorescent and Incandescent Lamps Public Meeting on Google Bookmark Building Technologies Office: Fluorescent and Incandescent Lamps Public Meeting on Delicious Rank Building Technologies Office: Fluorescent and Incandescent Lamps Public Meeting on Digg Find More places to share Building Technologies Office: Fluorescent and Incandescent Lamps Public Meeting on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement

89

Killing Effects of Hydroxyl Radical on Algae and Bacteria in Ships Ballast Water and on Their Cell Morphology  

Science Journals Connector (OSTI)

With the method of strong electric-field discharge, the treatments of ships ballast water [13, 14] and red tide in ocean [5...] using OH radicals were performed in our laboratory. Based on the D-2 ballast water...

Mindong Bai; Zhitao Zhang; Xiaohong Xue

2010-12-01T23:59:59.000Z

90

Bacteria in Ballast Water: The Shipping Industry's Contributions to the Transport and Distribution of Microbial Species in Texas  

E-Print Network (OSTI)

of the ballast tank bacterial community has not been examined. This study is the first to characterize the total bacterial community within a ballast tank by constructing a clone library from a ballast water sample from a cargo ship in the Port of Houston...

Neyland, Elizabeth B.

2010-10-12T23:59:59.000Z

91

Energy Cost Calculator for Compact Fluorescent Lamps | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Compact Fluorescent Lamps Compact Fluorescent Lamps Energy Cost Calculator for Compact Fluorescent Lamps October 8, 2013 - 2:18pm Addthis This tool calculates the payback period for your calc retrofit project. Modify the default values to suit your project requirements. Existing incandescent lamp wattage Watts Incandescent lamp cost dollars Incandescent lamp life 1000 hours calc wattage Watts calc cost dollars calc life (6000 hours for moderate use, 10000 hours for high use) 8000 hours Number of lamps in retrofit project Hours operating per week hours Average cost of electricity 0.06 $/kWh Relamper labor costs $/hr Time taken to retrofit all lamps in this project min Time taken to relamp one lamp min Type of Relamping Practiced: Group Relamping: Calculate Simple Payback Period months

92

Comparison of technologies for new energy-efficient lamps  

SciTech Connect

Energy-efficient light bulbs are being developed to replace the incandescent lamp where they can satisfy the design criteria and be used in sockets that have long hours of annual use. The four technologies discussed here include the compact fluorescent lamp, coated-filament lamp, electrodeless fluorescent lamp, and compact high-intensity discharge lamp. The systems demonstrate efficacy improvements of two to four times that of their incandescent counterparts. These new lamps have required considerable advances in lamp technology. They offer the potential for achieving efficacies close to 80 lumens per watt. These new lamps will reduce the energy used annually by incandescent lamps (190 BkWh) by more than 50% in the 1990s, at which times they will be commonly employed.

Verderber, R.R.; Rubinstein, F.R.

1983-06-01T23:59:59.000Z

93

Comparison of technologies for new energy-efficient lamps  

SciTech Connect

Energy-efficient light bulbs are being developed to replace the incandescent lamp where they can satisfy the design criteria and be used in sockets that have long hours of annual use. The four technologies discussed include the compact fluorescent lamp, coated-filament lamp, electrodeless fluorescent lamp, and compact high-intensity discharge lamp. The systems demonstrate efficacy improvements of two to four times that of their incandescent counterparts. These new lamps have required considerable advances in lamp technology. They offer the potential for achieving efficacies close to 80 lm/W. These new lamps will reduce the energy used annually by incandescent lamps (190 billion kWh) by more than 50 percent in the 1990's, at which times they will be commonly employed.

Verderber, R.R.; Rubinstein, F.M.

1984-09-01T23:59:59.000Z

94

U.S. Department of Energy NEPA Categorical Exclusion Determination Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

fO( Energy Conservation Standards for Metal Halide lamp Fixtures (RIN: 1904-ACOO) fO( Energy Conservation Standards for Metal Halide lamp Fixtures (RIN: 1904-ACOO) Program or Fjeld Office: EERE- Buildings Technology Program Location(s) (City/CQunty/Statel: Nationwide Proposed Action Description: DOE proposes amended energy conservation standards for metal halide lamp fixtures. The proposed standards are the minimum allowable ballast efficiency based on fixture location, ballast type. and the rated wattage of the lamp. These proposed standards, if adopted, would apply to aU products listed in Table 1.1 of the NOPR and manufactured in, or imported into, the United States on or after January 1, 2015. Categorical ExclusiQn(s) Applied: 85.1 - Actions to conserve energy or waler For the complete DOE National Environmental Policy Act regulations regarding categorical eXClusions, including the full text of

95

Laboratory Evaluation of LED T8 Replacement Lamp Products  

SciTech Connect

A report on a lab setting analysis involving LED lamps intended to directly replace T8 fluorescent lamps (4') showing light output, power, and economic comparisons with other fluorescent options.

Richman, Eric E.; Kinzey, Bruce R.; Miller, Naomi J.

2011-05-23T23:59:59.000Z

96

Max Tech and Beyond: High-Intensity Discharge Lamps  

E-Print Network (OSTI)

formation of the electric discharge arc and the metals emitdefined as electric discharge lamps in which the arc tubelamp - an electric discharge lamp in which the arc tube wall

Scholand, Michael

2012-01-01T23:59:59.000Z

97

Text-Alternative Version: LED Replacements for Linear Fluorescent Lamps  

Energy.gov (U.S. Department of Energy (DOE))

Below is the text-alternative version of the "LED Replacements for Linear Fluorescent Lamps" webcast, held June 20, 2011.

98

The provenance of the stone ballast from the Molasses Reef Wreck  

E-Print Network (OSTI)

the ballast-mound strati graphy was recorded 13 Sorted ballast from section 13 of the LM cross section 15 Original hand-specimen sample form. 18 A simpiified hand-specimen sample form employed on the centerline cross section ba 1 I ast stones 18... reasonably well but the l2 Figure 2. View of the MRW ballast mound from the south end. (Photo courtesy of INA staff) 0 1 2 1" 1 I 0-aa 0- 1 ~ LM TRANSECT MN TRANSECT 04 TRANSECT MID 4 THAHSKCT Cf NTERLINK 1 - 1 33 KL TRANSECT NORTH \\3 3031...

Lamb, William Reginald

2012-06-07T23:59:59.000Z

99

Faster Dissociation: Aryl Halide Radical Anions  

NLE Websites -- All DOE Office Websites (Extended Search)

Faster Dissociation: Measured Rates and Computed Effects on Barriers in Faster Dissociation: Measured Rates and Computed Effects on Barriers in Aryl Halide Radical Anions Norihiko Takeda, Pavel V. Poliakov, Andrew R. Cook, and John R. Miller J. Am. Chem. Soc. 126, 4301-4309 (2004). [Find paper at ACS Publications] Abstract: Carbon-halogen bond dissociation rates for a series of aryl halide radical anions (ArX-·: X = Cl, Br) in NMP were measured at room temperature by pulse radiolysis with 10-11 s time resolution. To obtain accurate dissociation rates, care was taken to measure and correct for competing decay channels. The observed rates correlated well with activation energies computed in the gas phase by density functional (DFT) calculations. The rates did not correlate well with electron affinities or dissociation energies obtained by the same computational methods, although such

100

Lanthanide-halide based humidity indicators  

DOE Patents (OSTI)

The present invention discloses a lanthanide-halide based humidity indicator and method of producing such indicator. The color of the present invention indicates the humidity of an atmosphere to which it is exposed. For example, impregnating an adsorbent support such as silica gel with an aqueous solution of the europium-containing reagent solution described herein, and dehydrating the support to dryness forms a substance with a yellow color. When this substance is exposed to a humid atmosphere the water vapor from the air is adsorbed into the coating on the pore surface of the silica gel. As the water content of the coating increases, the visual color of the coated silica gel changes from yellow to white. The color change is due to the water combining with the lanthanide-halide complex on the pores of the gel.

Beitz, James V. (Hinsdale, IL); Williams, Clayton W. (Chicago, IL)

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

High-Intensity Discharge Lamps High-Intensity Discharge Lamps Sign up for e-mail updates on regulations for this and other products There are currently no energy conservation standards for high-intensity discharge (HID) lamps. HID lamps are electric discharge lamps and include high-pressure sodium, mercury vapor, and metal halide lamps. HID lamps require an HID ballast to start and regulate electric current flow through the lamp. HID lamps are used in street and roadway lighting, area lighting such as for parking lots and plazas, industrial and commercial building interior lighting, security lighting for commercial, industrial, and residential spaces, and landscape lighting. The Standards and Test Procedures for this product are related to Rulemaking for High Intensity Discharge Lamps Energy Conservation Standard and Rulemaking for High Intensity Discharge Lamps Test Procedures.

102

Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and  

E-Print Network (OSTI)

Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and HID (high-intensity discharge) lamps and all other mercury containing labeled for shipment to a recycling plant for mercury, glass and aluminum recovery. The beneficial re

Baker, Chris I.

103

LED lamp color control system and method  

SciTech Connect

An LED lamp color control system and method including an LED lamp having an LED controller 58; and a plurality of LED channels 60 operably connected to the LED controller 58, each of the plurality of LED channels 60 having a channel switch 62 in series with at least one shunted LED circuit 83, the shunted LED circuit 83 having a shunt switch 68 in parallel with an LED source 80. The LED controller 58 determines whether the LED source 80 is in a feedback controllable range, stores measured optical flux for the LED source 80 when the LED source 80 is in the feedback controllable range, and bypasses storing the measured optical flux when the LED source 80 is not in the feedback controllable range.

Gaines, James; Clauberg, Bernd; Van Erp, Josephus A.M.

2013-02-05T23:59:59.000Z

104

Studies of non-proportionality in alkali halide and strontium iodide scintillators using SLYNCI  

E-Print Network (OSTI)

in Alkali Halide and Strontium Iodide Scintillators Usingof europium doping level in strontium iodide. Directions offor several alkali halides, strontium iodide, and lanthanum

Ahle, Larry

2011-01-01T23:59:59.000Z

105

E-Print Network 3.0 - alkali halide crystals Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

STUDIES IN ALKALI HALIDES Summary: of the alkali halides (KC1) the introduction of vacancies by thermal quenching of unirra- diated crystals has... ANNIHILATION STUDIES IN...

106

Gas-Phase Identity SN2 Reactions of Halide Anions and Methyl Halides with Retention of Configuration  

E-Print Network (OSTI)

Gas-Phase Identity SN2 Reactions of Halide Anions and Methyl Halides with Retention back-side and front-side SN2 reactions are found to involve the same ion-molecule complex (X-,,,H3CX of a front-side SN2 reaction with retention of configuration at saturated carbon. Analysis of our

Schlegel, H. Bernhard

107

RF driven sulfur lamp having driving electrodes arranged to cool the lamp  

DOE Patents (OSTI)

A high intensity discharge lamp without mercury is disclosed radiating a selected spectrum of which can be almost entirely in the visible range from an envelope that contains a sulfur containing substance. The lamp utilizes a signal source that generates an excitation signal that is externally coupled to the exterior surface of the envelope to excite the enclosed sulfur containing substance. Various embodiments of the lamp use electrodes adjacent the envelope to couple the excitation signal thereto with the face of the electrodes shaped to complement the shape of the exterior surface of the envelope. Two shapes discussed are spherical and cylindrical. To minimize filamentary discharges each envelope may include an elongated stem affixed to the exterior thereof whereby a rotational subsystem spins the envelope. In yet another embodiment the envelope has a Dewar configuration with two electrodes, one positioned near the external curved side surface of the body, and a second to the inner surface of the hole through the envelope. Further, the envelope may contain a backfill of a selected inert gas to assist in the excitation of lamp with that backfill at a pressure of less than 1 atmosphere, wherein the backfill pressure is directly related to the increase or decrease of peak output and inversely related to the increase and decrease of the emitted spectrum from the envelope. The emitting fill can be less than 6 mg/cc, or at least 2 mg/cc of the envelope of a sulfur containing substance. 17 figs.

Gabor, G.; Orr, T.R.; Greene, C.M.; Crawford, D.G.; Berman, S.M.

1998-10-20T23:59:59.000Z

108

The National Energy Policy Act and lamp replacement options  

SciTech Connect

The National Policy Act of 1992 involves the creation of energy efficiency standards for a wide range of products including fluorescent and incandescent lamps. Minimum efficacy (lumens per watt) and color rendering index (CRI) standards are mandated for the popular fluorescent lamps: four-foot medium bi-pin, two-foot U-bent, eight-foot slimline and eight-foot high output. Minimum efficacies are mandated for specific incandescent R and PAR reflector lamps. These standards will affect selected colors and designs of fluorescent lamps, the most significant being the standard lamps in the cool white and warm white colors. The incandescent reflector lamps will include the R-30, R-40, PAR-38 lamps above 40 watts, excluding the halogen types. These efficiency and color rendering standards will require end-users and specifiers to select replacement fluorescent lamps from a range of performance characteristics (lumen output, efficacy, CRI and price). The choice of replacement for the R and PAR incandescent lamps will include the halogen designs and compact fluorescent designs. In this paper, replacement options will be analyzed and discussed and the effect of these options on the performance of the lighting system will be explored in detail.

Ryerson, C.

1995-06-01T23:59:59.000Z

109

Max Tech and Beyond: High-Intensity Discharge Lamps  

E-Print Network (OSTI)

of color compared with the incandescent reference source isin this report. Standard Incandescent Halogen Low-Pressure:value equivalent to an incandescent filament lamp. Taking

Scholand, Michael

2012-01-01T23:59:59.000Z

110

Ecosystem under pressure: Ballast water discharge into Galveston Bay, Texas (USA) from 2005 to 2010  

Science Journals Connector (OSTI)

Ballast water exchange processes facilitate the dispersal and unnatural geographic expansion of phytoplankton, including harmful algal bloom species. From 2005 to 2010, over 45,000 vessels (?8000 annually) travelled across Galveston Bay (Texas, USA) to the deep-water ports of Houston (10th largest in the world), Texas City and Galveston. These vessels (primarily tankers and bulkers) discharged ?1.2נ108metrictons of ballast water; equivalent to ?3.4% of the total volume of the Bay. Over half of the ballast water discharged had a coastwise origin, 96% being from US waters. Galveston Bay has fewer non-indigenous species but receives a higher volume of ballast water discharge, relative to the highly invaded Chesapeake and San Francisco Bays. Given the magnitude of shipping traffic, the role of Galveston Bay, both as a recipient and donor region of non-indigenous phytoplankton species is discussed here in terms of the invasibility risk to this system by way of ballast water.

Jamie L. Steichen; Rachel Windham; Robin Brinkmeyer; Antonietta Quigg

2012-01-01T23:59:59.000Z

111

Lamp for generating high power ultraviolet radiation  

DOE Patents (OSTI)

The apparatus is a gas filled ultraviolet generating lamp for use as a liquid purifier. The lamp is powred by high voltage AC, but has no metallic electrodes within or in contact with the gas enclosure which is constructed as two concentric quartz cylinders sealed together at their ends with the gas fill between the cylinders. Cooling liquid is pumped through the volume inside the inner quartz cylinder where an electrically conductive pipe spaced from the inner cylinder is used to supply the cooling liquid and act as the high voltage electrode. The gas enclosure is enclosed within but spaced from a metal housing which is connected to operate as the ground electrode of the circuit and through which the treated fluid flows. Thus, the electrical circuit is from the central pipe, and through the cooling liquid, the gas enclosure, the treated liquid on the outside of the outer quartz cylinder, and to the housing. The high voltage electrode is electrically isolated from the source of cooling liquid by a length of insulated hose which also supplies the cooling liquid.

Morgan, Gary L. (Elkridge, MD); Potter, James M. (Los Alamos, NM)

2001-01-01T23:59:59.000Z

112

Field Validated Discrete Element Model for Railroad Ballast Erol Tutumluer, Yu Qian, Youssef Y.M.A. Hashash, and Jamshid Ghaboussi  

E-Print Network (OSTI)

on a curve at the TTC FAST test track. During the ballast layer construction, settlement plates were also

Illinois at Urbana-Champaign, University of

113

Magnetic polarizations of electrons at dislocations in alkali halides  

E-Print Network (OSTI)

interval. 25 NAGNETIC POLARIZATIONS OF ELECTRONS AT DISLOCATIONS IN ALKALI HALIDES 1. INTRODUCTION. The new magnetic effects observed in our laboratory on a number of single crystals of alkali halides are thought to be caused by electrons trapped... on d1slocations. The magnet1c properties are perhaps more interesting as a bas1c contribution to the sc1ence of magnetism than to a knowledge of d. islocations 1n these very pure, optically clear, s1ngle crystals of alkal1 halides. The gross magnet...

McClurg, Gene Roark

2012-06-07T23:59:59.000Z

114

DEFINING THE EFFECTIVENESS OF UV LAMPS  

Office of Scientific and Technical Information (OSTI)

ARTI-21CR/610-40030-01 ARTI-21CR/610-40030-01 DEFINING THE EFFECTIVENESS OF UV LAMPS INSTALLED IN CIRCULATING AIR DUCTWORK Final Report Date Published - November 2002 Douglas VanOsdell and Karin Foarde RTI P.O. Box 12194 Research Triangle Park, NC 27709-2194 Prepared for the AIR-CONDITIONING AND REFRIGERATION TECHNOLOGY INSTITUTE 4100 N. Fairfax Drive, Suite 200, Arlington, Virginia 22203 Distribution A - Approved for public release; further dissemination unlimited. DISCLAIMER This report was prepared as an account of work sponsored by the Air-Conditioning and Refrigeration Technology Institute (ARTI) under its "HVAC&R Research for the 21 st Century" (21-CR) program. Neither ARTI, the financial supporters of the 21-CR program, or any agency

115

Alkylaluminum Halide Induced Reactions of Carbonyl Compounds with Unactivated Alkenes  

Science Journals Connector (OSTI)

Aldehydes, ketones and ?,?-unsaturated aldehydes and ketones undergo a wide variety of reactions with unactivated alkenes in the presence of alkylaluminum halide catalysts. Ene reactions, Diels-Alder reactions...

Barry B. Snider

1989-01-01T23:59:59.000Z

116

NREL Investigates Critical Properties of Perovskite Halides Solar...  

NLE Websites -- All DOE Office Websites (Extended Search)

Organometallic halide perovskites (e.g., CH 3 NH 3 PbI 3 ) are a novel class of light- absorbing materials that have demon- strated exceptional progress in solar cell...

117

Application Summary Report 22: LED MR16 Lamps  

SciTech Connect

This report analyzes the independently tested photometric performance of 27 LED MR16 lamps. It describes initial performance based on light output, efficacy, distribution, color quality, electrical characteristics, and form factor, with comparisons to a selection of benchmark halogen MR16s and ENERGY STAR qualification thresholds. Three types of products were targeted. First, CALiPER sought 3000 K lamps with the highest rated lumen output (i.e., at least 500 lm) or a claim of equivalency to a 50 W halogen MR16 or higher. The test results indicate that while the initial performance of LED MR16s has improved across the board, market-available products still do not produce the lumen output and center beam intensity of typical 50 W halogen MR16 lamps. In fact, most of the 18 lamps in this category had lower lumen output and center beam intensity than a typical 35 W halogen MR16 lamp. Second, CALiPER sought lamps with a CRI of 90 or greater. Only four manufacturers were identified with a product in this category. CALiPER testing confirmed the performance of these lamps, which are a good option for applications where high color fidelity is needed. A vast majority of the LED MR16 lamps have a CRI in the low 80s; this is generally acceptable for ambient lighting, but may not always be acceptable for focal lighting. For typical LED packages, there is a fundamental tradeoff between CRI and efficacy, but the lamps in the high-CRI group in this report still offer comparable performance to the rest of the Series 22 products in other performance areas. Finally, CALiPER sought lamps with a narrow distribution, denoted as a beam angle less than 15. Five such lamps were purchased. Notably, no lamp was identified as having high lumen output (500 lumens or greater), high CRI (90 or greater), a narrow distribution (15 or less), and an efficacy greater than 60 lm/W. This would be an important achievement for LED MR16s especially if output could reach approximately 700 800 lumens, or the approximate equivalent of a 50 W halogen MR16 lamp. Many factors beyond photometric performance should be considered during specification. For example, performance over time, transformer and dimmer compatibility, and total system performance are all critical to a successful installation. Subsequent CALiPER reports will investigate more complex issues.

Royer, Michael P.

2014-07-23T23:59:59.000Z

118

Highly Efficient Small Form Factor LED Retrofit Lamp  

SciTech Connect

This report summarizes work to develop a high efficiency LED-based MR16 lamp downlight at OSRAM SYLVANIA under US Department of Energy contract DE-EE0000611. A new multichip LED package, electronic driver, and reflector optic were developed for these lamps. At steady-state, the lamp luminous flux was 409 lumens (lm), luminous efficacy of 87 lumens per watt (LPW), CRI (Ra) of 87, and R9 of 85 at a correlated color temperature (CCT) of 3285K. The LED alone achieved 120 lumens per watt efficacy and 600 lumen flux output at 25 C. The driver had 90% electrical conversion efficiency while maintaining excellent power quality with power factor >0.90 at a power of only 5 watts. Compared to similar existing MR16 lamps using LED sources, these lamps had much higher efficacy and color quality. The objective of this work was to demonstrate a LED-based MR16 retrofit lamp for replacement of 35W halogen MR16 lamps having (1) luminous flux of 500 lumens, (2) luminous efficacy of 100 lumens per watt, (3) beam angle less than 40{sup o} and center beam candlepower of at least 1000 candelas, and (4) excellent color quality.

Steven Allen; Fred Palmer; Ming Li

2011-09-11T23:59:59.000Z

119

Project Profile: Halide and Oxy-Halide Eutectic Systems for High-Performance, High-Temperature Heat Transfer Fluids  

Energy.gov (U.S. Department of Energy (DOE))

The University of Arizona along with partners at Arizona State University and Georgia Institute of Technology, under the 2012 Multidisciplinary University Research Initiative (MURI): High Operating Temperature (HOT) Fluids funding opportunity, is investigating the use of halide salts with oxy-halide additives as a heat transfer fluid (HTF) in concentrating solar power (CSP) systems operating at temperatures greater than 800C. By allowing higher temperature operation, CSP systems can achieve greater efficiencies and thereby reduce the overall system cost.

120

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

E-Print Network (OSTI)

Fluorescent Lamps and Incandescent Reflector Lamps MediumBallasts and Fixtures General Service Incandescent Lamps,Intermediate Base Incandescent Lamps and Candelabra Base

Meyers, Stephen

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Maintaining optimum fluorescent lamp performance under elevated temperature conditions  

SciTech Connect

This paper describes a new technique for optimizing fluorescent lamp performance under elevated temperature conditions. This approach uses a thermo-electric Peltier device to produce a localized cold spot temperature of approximately 40/sup 0/C, allowing the lamps to maintain maximum light output and efficacy independent of prevailing ambient temperatures inside a luminaire. Experimental data show that a 20% increase in light output and a 10% increase in efficacy over typical lamp performance in a warm fixture environment can be obtained using this device. Only 0.25 watts must be supplied to the Peltier device to produce these results.

Siminovitch, M.J.; Rubinstein, F.M.; Clark, T.A.; Verderber, R.R.

1986-04-01T23:59:59.000Z

122

Covered Product Category: Compact Fluorescent Lamps | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Covered Product Category: Compact Fluorescent Lamps Covered Product Category: Compact Fluorescent Lamps Covered Product Category: Compact Fluorescent Lamps October 7, 2013 - 10:48am Addthis ENERGY STAR Qualified Products Federal Energy Management Program (FEMP) provides acquisition guidance across a variety of product categories, including compact fluorescent lamps (CFLs), which are an ENERGY STAR-qualified product category. Federal laws and executive orders mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law. Most manufacturers display the ENERGY STAR label on complying models. For a model not displaying this label, check the manufacturer's literature to determine if it meets the efficiency requirements outlined by ENERGY STAR.

123

Information Resources: LED Replacements for Linear Fluorescent Lamps  

NLE Websites -- All DOE Office Websites (Extended Search)

Replacements for Linear Fluorescent Lamps Webcast Replacements for Linear Fluorescent Lamps Webcast In this June 20, 2011 webcast on LED products marketed as replacements for linear fluorescent lamps, Jason Tuenge of the Pacific Northwest National Laboratory (PNNL) discussed current Lighting Facts-listed products as well as products evaluated in the latest CALiPER reports. Eric Richman, also of PNNL, reported on a recently completed GATEWAY demonstration project, in which LED and fluorescent lamps were installed in a variety of recessed troffer luminaires for comparison in an office environment. The presentation concluded with a discussion of specifications listed in a newly updated technology fact sheet. View presentation slides View the text-alternative version View the webcast (WMV 16 MB) Download Windows Media Player

124

Burst Radio-Frequency Excited Pulsed Hollow-Cathode Lamp  

Science Journals Connector (OSTI)

Transient emission characteristics of a hollow-cathode lamp driven by a pulsed current in combination with a radio-frequency burst signal are described. The radio-frequency field...

Araki, Tsutomu; Walters, John P; Minami, Shigeo

1980-01-01T23:59:59.000Z

125

DOE Publishes Long-Term Testing Investigation of Retail Lamps  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of Energy's CALiPER program has released another special report on LED lamps that are available through the retail marketplace and targeted toward general consumers. CALiPER...

126

Conservation Potential of Compact Fluorescent Lamps in India and Brazil  

E-Print Network (OSTI)

38 TWh, 10% of which was for incandescent lighting (Fig. 3).The electricity consumed in incandescent lighting can be300 and 400 million incandescent lamps in the country. Let

Gadgil, A.J.

2008-01-01T23:59:59.000Z

127

DOE Publishes New CALiPER Report on Retail Lamps  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of Energy's CALiPER program has released a special report on LED lamps available through the retail marketplace and targeted toward general consumers. While previous reports in...

128

Magnetic fluorescent lamp having reduced ultraviolet self-absorption  

DOE Patents (OSTI)

The radiant emission of a mercury-argon discharge in a fluorescent lamp assembly (10) is enhanced by providing means (30) for establishing a magnetic field with lines of force along the path of electron flow through the bulb (12) of the lamp assembly, to provide Zeeman splitting of the ultraviolet spectral line. Optimum results are obtained when the magnetic field strength causes a Zeeman splitting of approximately 1.7 times the thermal line width.

Berman, Samuel M. (San Francisco, CA); Richardson, Robert W. (Pelham, NY)

1985-01-01T23:59:59.000Z

129

Perceptions of compact fluorescent lamps in the residential market  

SciTech Connect

Compact fluorescent lamps offer significant energy savings over other forms of residential lighting and last up to 10 times longer than conventional incandescent bulbs. In order to better understand existing barriers to acceptance and future opportunities for growth of compact fluorescent lighting in the residential retrofit sector, a three stage research project was designed and conducted by MACRO Consulting, Inc. Assessment of whether or not the benefits of compact fluorescent lamps are sufficient to overcome price resistance was one of the major purposes of this project. Residential customers were interviewed in focus group sessions to help determine key issues and motivating forces in the lighting/energy saving/cost saving equation. Residential customers in 5 major market areas were contacted by telephone, and data about their awareness, knowledge and use of compact fluorescent lighting were collected. These customers also participated in an attribute rating exercise in which compact fluorescent lamps were compared with fluorescent tubes and incandescent bulbs on a series of product attributes. A price elasticity exercise was also conducted. Teleconferences with retailers of compact fluorescent lamps were conducted in order to explore their knowledge of and attitudes towards compact fluorescent lamps. Customers agree that energy savings and longer life are both positive attributes for residential lighting products, but they are not yet ready to make the switch away from inexpensive, versatile and readily available incandescent bulbs to compact fluorescent lamps. Compact fluorescent lamps are rated poorly (even by satisfied'' users) on each of seven positive attributes of home lighting. Major barriers to increased use of compact fluorescent lamps include price, convenience, and performance. Prices above $10 are considered outrageous''. Product improvements are needed for appearance, light output and versatility.

Weiner, J.; Campbell, C.J. (Macro Consulting, Inc., Mountain View, CA (United States))

1992-07-01T23:59:59.000Z

130

A light diet for a giant appetite: An assessment of China's proposed fluorescent lamp standard  

E-Print Network (OSTI)

standard for linear fluorescent lamps Length (mm) Minimum efficacy (lm/W) Efficacy for energy conservation

Lin, Jiang

2002-01-01T23:59:59.000Z

131

Vitrification of IFR and MSBR halide salt reprocessing wastes  

SciTech Connect

Both of the genuinely sustainable (breeder) nuclear fuel cycles (IFR - Integral Fast Reactor - and MSBR - Molten Salt Breeder Reactor -) studied by the USA's national laboratories would generate high level reprocessing waste (HLRW) streams consisting of a relatively small amount ( about 4 mole %) of fission product halide (chloride or fluoride) salts in a matrix comprised primarily (about 95 mole %) of non radioactive alkali metal halide salts. Because leach resistant glasses cannot accommodate much of any of the halides, most of the treatment scenarios previously envisioned for such HLRW have assumed a monolithic waste form comprised of a synthetic analog of an insoluble crystalline halide mineral. In practice, this translates to making a 'substituted' sodalite ('Ceramic Waste Form') of the IFR's chloride salt-based wastes and fluoroapatite of the MSBR's fluoride salt-based wastes. This paper discusses my experimental studies of an alternative waste management scenario for both fuel cycles that would separate/recycle the waste's halide and immobilize everything else in iron phosphate (Fe-P) glass. It will describe both how the work was done and what its results indicate about how a treatment process for both of those wastes should be implemented (fluoride and chloride behave differently). In either case, this scenario's primary advantages include much higher waste loadings, much lower overall cost, and the generation of a product (glass) that is more consistent with current waste management practices. (author)

Siemer, D.D. [Idaho National Laboratory, 12N 3167E, Idaho Falls, ID 83402 (United States)

2013-07-01T23:59:59.000Z

132

Johnson County REMC - Commercial Energy Efficiency Rebate Program (Indiana)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Johnson County REMC - Commercial Energy Efficiency Rebate Program Johnson County REMC - Commercial Energy Efficiency Rebate Program (Indiana) Johnson County REMC - Commercial Energy Efficiency Rebate Program (Indiana) < Back Eligibility Commercial Industrial Savings Category Heating & Cooling Commercial Heating & Cooling Cooling Heat Pumps Appliances & Electronics Commercial Lighting Lighting Manufacturing Maximum Rebate Pre-approval required for payments greater than $1,000 Program Info State Indiana Program Type Utility Rebate Program Rebate Amount T5/T8 Lamps with Electronic Ballasts: $8 - $18 T8 Lamps: $0.75/lamp High Bay Fluorescent Fixtures with Electronic Ballasts: $50 - $125 Hardwired/Modular CFL Fixtures: $8 - $25 Ceramic Metal Halide Accent/Directional Lighting: $20 - $50 Pulse Start Metal Halide Fixtures: $25 - $65

133

CX-007916: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

916: Categorical Exclusion Determination 916: Categorical Exclusion Determination CX-007916: Categorical Exclusion Determination Notice of Proposed Rulemaking for( Energy Conservation Standards for Metal Halide lamp Fixtures CX(s) Applied: B5.1 Date: 01/04/2012 Location(s): Nationwide Offices(s): Energy Efficiency and Renewable Energy DOE proposes amended energy conservation standards for metal halide lamp fixtures. The proposed standards are the minimum allowable ballast efficiency based on fixture location, ballast type. and the rated wattage of the lamp. These proposed standards, if adopted, would apply to all products listed in Table 1.1 of the Notice of Proposed Rulemaking and manufactured in, or imported into, the United States on or after January 1, 2015. U.S. Department of Energy NEPA Categorical Exclusion Determination Form

134

All mercury lamps contain small amounts of mercury. An electric current passes through the lamp and vaporizes the mercury to generate light. Recycling mercury containing lamps protects human health and our environment from heavy  

E-Print Network (OSTI)

All mercury lamps contain small amounts of mercury. An electric current passes through the lamp and vaporizes the mercury to generate light. Recycling mercury containing lamps protects human health and our the environment by recycling universal wastes, contact EH&S at (949) 824-6200 or visit: www.ehs.uci.edu Mercury

George, Steven C.

135

Photoinduced Giant Dielectric Constant in Lead Halide Perovskite Solar Cells  

Science Journals Connector (OSTI)

Perovskite solar cells have emerged as a major topic of research in photovoltaics because of the promising properties of the solution processed, low cost, and high efficiency solar cells for large-scale solar energy production. ... Illumination of the perovskite samples produces a significant increase of charge carrier density in the perovskite layer due to the high extinction coefficient of organicinorganic lead halide perovskite. ... The effect of electron- and hole-selective contacts in the final cell performance of hybrid lead halide perovskite, CH3NH3PbI3, solar cells has been systematically analyzed by impedance spectroscopy. ...

Emilio J. Juarez-Perez; Rafael S. Sanchez; Laura Badia; Germ Garcia-Belmonte; Yong Soo Kang; Ivan Mora-Sero; Juan Bisquert

2014-06-23T23:59:59.000Z

136

Assessing the Risk of Mercury in Drinking Water after UV Lamp Breaks Page 1 Assessing the Risk of Mercury in Drinking Water after UV Lamp Breaks  

E-Print Network (OSTI)

Assessing the Risk of Mercury in Drinking Water after UV Lamp Breaks Page 1 Assessing the Risk of Mercury in Drinking Water after UV Lamp Breaks Heidi Borchers University of New Hampshire, Environmental Ultraviolet (UV) lamps generate ultraviolet light through the vaporization of elemental mercury, by using

137

Catalog of DC Appliances and Power Systems  

E-Print Network (OSTI)

bulb or tube, a compact fluorescent lamp typically includes an integral ballast, as do HID lamps, and an LED

Garbesi, Karina

2012-01-01T23:59:59.000Z

138

TRANSMISSION ELECTRON MICROSCOPY OF WEAKLY DEFORMED ALKALI HALIDE CRYSTALS  

E-Print Network (OSTI)

377 TRANSMISSION ELECTRON MICROSCOPY OF WEAKLY DEFORMED ALKALI HALIDE CRYSTALS H. STRUNK Max'importance croissante du durcissement de la solution solide. Abstract. 2014 Transmission electron microscopy (TEM Abstracts 7j66 - 7 I' 1. Introduction. - It is only some years ago that transmission electron microscopy

Boyer, Edmond

139

EA-1881: Final Environmental Assessment  

Energy.gov (U.S. Department of Energy (DOE))

Energy Conservation Program: Energy Conservation Standards for Fluorescent Lamp Ballasts (October 2011)

140

2014-12-30 Issuance: Energy Conservation Standard for General Service Fluorescent Lamps and Incandescent Reflector Lamps; Final Rule  

Energy.gov (U.S. Department of Energy (DOE))

This document is a pre-publication Federal Register final rule regarding energy conservation standards for general service fluorescent lamps and incandescent reflector lamps, as issued by the Deputy Assistant Secretary for Energy Efficiency on December 30, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Confirmation of the chromosomal localization of human lamp genes and their exclusion as candidate genes for Salla disease  

Science Journals Connector (OSTI)

Salla disease is an inherited lysosomal storage disorder caused by accumulation of free sialic acid in the lysosomes. Lamp genes, lamp A and lamp B (lysosome associated membrane proteins), are the first known ...

Johanna Schleutker; Leena Haataja; Martin Renlund; Lea Puhakka

1991-11-01T23:59:59.000Z

142

BEFORE THE U.S. DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Engineered Products Company, Engineered Products Company, (metal halide lamp fixtures) ) ) ) ) ) Case Number: 2012-SE-5401 NOTICE OF PROPOSED CIVIL PENALTY Date issued: July 19, 2012 Number of alleged violations: 19 Maximum possible assessment: $3,800 Proposed civil penalty: $3,800 The U.S. Department of Energy ("DOE") Office of the General Counsel, Office of Enforcement, alleges that Engineered Products Company ("EPCO") has violated certain provisions of the Energy Policy and Conservation Act, 42 U.S. C.§ 6291 et seq. ("the Act"), and 10 C.P.R. Parts 429, 430, and 431. Specifically, DOE alleges: 1. EPCO's basic modell5701 is a metal halide lamp fixture with a magnetic probe-start ballast. 10 C.P.R.§§ 431.322, 431.326; 2. A metal halide lamp fixture is a "covered product" as defined in 42 U.S. C.§ 6292(a)(19)

143

Low-pressure microwave plasma ultraviolet lamp for water purification  

Science Journals Connector (OSTI)

Low-pressure mercury lamps are commonly used for germicidal applications. The germicidal effect is due to the emission of light at 254nm, which leads to the destruction of the most waterborne bacteria and viruses. The microwave plasma ultraviolet (UV) lamp (MPUVL) is a new technology for generating a high-intensity UV light and that can be also controlled to operate at 185nm; irradiation is in air at this wavelength produces ozone. The microwave power is injected into a resonant cavity and the surface wave excitation takes place within the cavity through that part of the discharge tube (fused silica) protruding inside it. The MPUVL has many advantages over conventional lamps, which are limited to an output power in the region of 30Wm-1, while MPUVL can deliver any amount of power per unit length and the tube can be of any shape, length or diameter. This paper describes the design of the MPUVL and compares its efficiency with that of conventional lamps through spectral analysis. Other results, which include the effects of temperature and different power inputs, are also discussed.

A I Al-Shamma'a; I Pandithas; J Lucas

2001-01-01T23:59:59.000Z

144

Solid-State Lighting: LED Replacement Lamps: Current Performance and the  

NLE Websites -- All DOE Office Websites (Extended Search)

LED Replacement Lamps: Current LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR® to someone by E-mail Share Solid-State Lighting: LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR® on Facebook Tweet about Solid-State Lighting: LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR® on Twitter Bookmark Solid-State Lighting: LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR® on Google Bookmark Solid-State Lighting: LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR® on Delicious Rank Solid-State Lighting: LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR® on Digg Find More places to share Solid-State Lighting: LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR® on

145

LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR  

Energy.gov (U.S. Department of Energy (DOE))

This May 19, 2009 webcast summarized CALiPER's recent benchmark testing of common omnidirectional incandescent lamps (e.g., A-lamps), and provided an update on ENERGY STAR criteria for LED integral...

146

Spectroscopic effects of disorder and vibrational localization in mixed-halide metal-halide chain solids  

SciTech Connect

Resonance Raman techniques, together with lattice-dynamics and Peierls-Hubbard modelling, are used to explore the electronic and vibrational dynamics of the quasi-one-dimensional metal-halogen chain solids [Pt(en){sub 2}][R(en){sub 2}X{sub 2}](ClO{sub 4}){sub 4}, (en = C{sub 2}H{sub 8}N{sub 2} and X=Cl, Br), abbreviated ``PLX.`` The mixed-halide materials PtCl{sub 1-x}Br{sub x} and PtCl{sub 1-x}I{sub x} consist of long mixed chains with heterojunctions between segments of the two constituent materials. Thus, in addition to providing mesoscale modulation of the chain electronic states, they serve as prototypes for elucidating the properties to be expected for macroscopic heterojunctions of these highly nonlinear materials. Once a detailed understanding of the various local vibrational modes occurring in these disordered solids is developed, the electronic structure of the chain segments and junctions can be probed by tuning the Raman excitation through their various electronic resonances.

Love, S.P.; Scott, B.; Worl, L.A.; Huckett, S.C.; Saxena, A.; Huang, X.Z.; Bishop, A.R.; Swanson, B.I.

1993-02-01T23:59:59.000Z

147

DOE Publishes CALiPER Report on Cost-Effectiveness of Linear (T8) LED Lamps  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of Energy's CALiPER program has released Report 21.3, which is part of a series of investigations on linear LED lamps. Report 21.3 details a set of life-cycle cost simulations that compared a two-lamp troffer using LED lamps (38W total power draw) or fluorescent lamps (51W total power draw) over a 10-year study period.

148

Summary of Substitution and Elimination Reactions of Alkyl Halides Polar protic solvent  

E-Print Network (OSTI)

will come from E2 and/or SN2, or there will be no reaction, depending upon the structure of the alkyl halide­X E2, SN2, E1/SN1 First, you need to know which products to expect from each mechanism. Second, you: 1) 1° halides will give SN2 unless the halide is hindered on the backside by branching

Walba, David

149

E-Print Network 3.0 - alkali halides irradiated Sample Search...  

NLE Websites -- All DOE Office Websites (Extended Search)

U ET ASSOCIATIONS DE CENTRES COLORES ATOMIC HYDROGEN CENTRES IN IONIC CRYSTALS Summary: . Abstract. - Experimental and theoretical work on atomic hydrogen centres in alkali halides...

150

E-Print Network 3.0 - absorbable organic halides Sample Search...  

NLE Websites -- All DOE Office Websites (Extended Search)

Collection: Chemistry 64 386 JACKHALPERN VOl. 3 xidative-AdditionReactions of Transition Metal Complexes Summary: peroxide, as well as various organic halides and metal...

151

Halide and Oxy-Halide Eutectic Systems for High-Performance, High-Temperature Heat Transfer Fluids  

Energy.gov (U.S. Department of Energy (DOE))

This fact sheet details a SunShot-funded solar project led by the University of Arizona to using ab initio computational modeling along with rapid material screening methods to identify halide salt mixtures with a melting point below 250C that are stable at temperatures well above 800C. This research has the potential to help concentrating solar power systems achieve greater efficiencies and reduce overall costs.

152

DuraLamp USA: Proposed Penalty (2010-CE-0912) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DuraLamp USA: Proposed Penalty (2010-CE-0912) DuraLamp USA: Proposed Penalty (2010-CE-0912) DuraLamp USA: Proposed Penalty (2010-CE-0912) September 9, 2010 DOE alleged in a Notice of Proposed Civil Penalty that DuraLamp USA, Inc. failed to certify a variety of general service fluorescent lamps as compliant with the applicable energy conservation standards. DOE regulations require a manufacturer (which includes importers) to submit reports certifying that its products have been tested and meet the applicable energy conservation standards. This civil penalty notice advises the company of the potential penalties and DOE's administrative process, including the company's right to a hearing. DuraLamp USA: Proposed Penalty (2010-CE-0912) More Documents & Publications DuraLamp USA: Order (2010-CE-0912)

153

Sulfur Lamps-The Next Generation of Efficient Light?  

NLE Websites -- All DOE Office Websites (Extended Search)

5 5 Sulfur Lamps-The Next Generation of Efficient Light? The figure above is a schematic of the system installed at the National Air and Space Museum and the DOE headquarters in Washington, D.C., Light from the sulfur lamp is focused by a parabolic reflector so that it enters the light pipe within a small angular cone. Light travels down the pipe, reflecting off the prismatic film (A) that lines the outer acrylic tube. The prismatic film reflects the light through total internal reflection (C), an intrinsically efficient process. Some of the light striking the film (at A) is not reflected and "leaks out" of the pipe walls (B), giving the pipe a glowing appearance. A light ray that travels all the way down the pipe will strike the mirror at the end (D) and return back up the pipe.

154

L Prize Competition Winner 60W Incandesent Replacement Lamp Update  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technology Deployment Technology Deployment Working Group L Prize ® Competition Winner 60W Incandescent Replacement Lamp Update James E. Rannels, Senior Advisor L Prize Competition D&R International May 23, 2012 Philips Wins First L Prize 2 * August 3, 2011: Philips announced as winner of 60W replacement bulb category * Product distributed thru commercial and retail channels Image courtesy of Philips -...[O]nce an award is made the authorizing Act directs General Services Administration to develop federal purchasing schedules for solid-state lamps that meet or exceed the specifications laid out in the prize category-so long as it is cost effective. I hope the GSA begins this process soon.‖

155

Efficacy of open-ocean ballast water exchange as a means of preventing invertebrate invasions between freshwater ports  

E-Print Network (OSTI)

between freshwater ports Derek K. Gray Great Lakes Institute for Environmental Research, University Lakes to European ports. Each vessel had paired ballast tanks, one of which was designated as a control ports. BWE was verified by ship records and, in two cases, by in situ water quality sensors. BWE

156

E-Print Network 3.0 - ammonium halides Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

POCl3, SOCl2, SO2Cl2 Anhydrous metal halides, such as AlCl3, TiCl4, ZrCl4, SnCl4... Phosphorus pentoxide Calcium carbide Organic acid halides and anhydrides of low molecular...

157

Photovoltaic experiment using light from a solar simulator lamp  

Science Journals Connector (OSTI)

A photovoltaic cellexperiment utilizing the convenience of a solar simulating type lamp is described. The circuit for obtaining the cell characteristic drives an X?Y plotter to graph continuously the characteristics from short circuit current to the open circuit voltage. Calibration methods and their limitation are discussed for estimating the irradiance to determine the light conversion efficiency of the cell. The diode junction nature of the cell is clearly supported by the agreement between experiment and theory. The experiment should be exceptionally suitable for an undergraduate physics laboratory experiment.

R. H. Chow

1980-01-01T23:59:59.000Z

158

Oxide Film Aging on Alloy 22 in Halide Containing Solutions  

SciTech Connect

Passive and corrosion behaviors of Alloy 22 in chloride and fluoride containing solutions, changing the heat treatment of the alloy, the halide concentration and the pH of the solutions at 90 deg. C, was investigated. The study was implemented using electrochemical techniques, which included open circuit potential monitoring over time, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) measurements carried out at open circuit and at passivity potentials. Corrosion rates obtained by EIS measurements after 24 h immersion in naturally aerated solutions were below 0.5 {mu}m/year. The corrosion rates were practically independent of solution pH, alloy heat treatment and halide ion nature and concentration. EIS low frequency resistance values increased with applied potential in the passive domain and with polarization time in pH 6 - 1 M NaCl at 90 deg. C. This effect was attributed to an increase in the oxide film thickness and oxide film aging. High frequency capacitance measurements indicated that passive oxide on Alloy 22 presented a double n-type/p-type semiconductor behavior in the passive potential range. (authors)

Rodriguez, Martin A.; Carranza, Ricardo M. [Dept. Materiales, Comision Nacional de Energia Atomica, Av. Gral. Paz 1499, Villa Maipu, 1650 (Argentina); Rebak, Raul B. [Lawrence Livermore National Laboratory, 7000 East Ave, L-631, Livermore, CA, 94550-9698 (United States)

2007-07-01T23:59:59.000Z

159

Text-Alternative Version: CALiPER Series 21 on LED Linear Lamps and Troffer Lighting  

Energy.gov (U.S. Department of Energy (DOE))

Following is a text version of a video about CALiPER Application Report Series 21 on LED Linear Lamps and Troffer Lighting.

160

Text-Alternative Version: LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR  

Energy.gov (U.S. Department of Energy (DOE))

Below is the text-alternative version of the LED Replacement Lamps: Current Performance and the Latest on ENERGY STAR webcast.

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

DOE Publishes Special CALiPER Report on Retail Lamps | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

retail marketplace and targeted toward general consumers. The report follows similar reports published in 2011 and 2012. LED replacement lamps are available through many retail...

162

LED Linear Lamps and Troffer Lighting: CALiPER Report Series 21  

SciTech Connect

Video about CALiPER Report Series 21 on LED Linear Lamps and Troffer Lighting, featuring interviews with Tracy Beeson and Naomi Miller of Pacific Northwest National Laboratory.

Beeson, Tracy; Miller, Naomi

2014-06-17T23:59:59.000Z

163

EA-1911: Energy Conservation Standards for Certain Reflector, Elliptical Reflector, and Bulged Reflector Incandescent Lamps  

Energy.gov (U.S. Department of Energy (DOE))

This EA will evaluate the environmental impacts of a proposal to amend energy conservation standards for Certain Reflector, Elliptical Reflector, and Bulged Reflector Incandescent Lamps.

164

Recombination Study of Combined Halides (Cl, Br, I) Perovskite Solar Cells  

Science Journals Connector (OSTI)

Recombination Study of Combined Halides (Cl, Br, I) Perovskite Solar Cells ... We report on the preparation of a series of solution-processed perovskite solar cells based on methylammonium (MA) lead halide derivatives, MAPbX3, which show tunable optical properties depending on the nature and ratio of the halides employed (X = Cl, Br, and I). ... These results highlight the crucial role of the charge-recombination processes on the performance of the perovskite solar cells and pave the way for further progress on this field. ...

Belen Suarez; Victoria Gonzalez-Pedro; Teresa S. Ripolles; Rafael S. Sanchez; Luis Otero; Ivan Mora-Sero

2014-04-17T23:59:59.000Z

165

J.-A. FLEMING. 2014 On the characteristic curves and surfaces of incandescence lamps (Courbes caractristiques des lampes incandescence) ; Phil. Mag.,  

E-Print Network (OSTI)

80 J.-A. FLEMING. 2014 On the characteristic curves and surfaces of incandescence lamps (Courbes caractéristiques des lampes à incandescence) ; Phil. Mag., 5e série, t. XIX, p. 368; I885. L'auteur étudie les résistance correspondant à la force électromotrice vo à laquelle l'incandescence commence à se produire, et r

Paris-Sud XI, Université de

166

Fabrication of alkali halide UV photocathodes by pulsed laser deposition  

SciTech Connect

A technique has been proposed for the fabrication of atmospheric corrosion resistant alkali halide UV photocathodes by pulsed laser deposition. We produced photocathodes with a highly homogeneous photoemissive layer well-adherent to the substrate. The photocathodes were mounted in a vacuum photodiode, and a tungsten grid was used as an anode. Using pulsed UV lasers, we carried out experiments aimed at evaluating the quantum efficiency of the photocathodes. With a dc voltage applied between the photocathode and anode grid, we measured a shunt signal proportional to the total charge emitted by the cathode exposed to UV laser light. The proposed deposition technique enables one to produce photocathodes with photoemissive layers highly uniform in quantum efficiency, which is its main advantage over thin film growth by resistive evaporation. (laser technologies)

Brendel', V M; Bukin, V V; Garnov, Sergei V; Bagdasarov, V Kh; Denisov, N N; Garanin, Sergey G; Terekhin, V A; Trutnev, Yurii A

2012-12-31T23:59:59.000Z

167

Demonstration Of A Monitoring Lamp To Visualize The Energy Consumption In Houses  

E-Print Network (OSTI)

Demonstration Of A Monitoring Lamp To Visualize The Energy Consumption In Houses Christophe Gisler1://www.unipg.it Abstract. We report on the development of a wireless lamp dedicated to the feedback of energy consumption is a good solution to make people gain awareness of their energy consumption and hence reduce it [1

Paris-Sud XI, Université de

168

Spectral irradiance model for tungsten halogen lamps in 340-850 nm wavelength range  

SciTech Connect

We have developed a physical model for the spectral irradiance of 1 kW tungsten halogen incandescent lamps for the wavelength range 340-850 nm. The model consists of the Planck's radiation law, published values for the emissivity of tungsten, and a residual spectral correction function taking into account unknown factors of the lamp. The correction function was determined by measuring the spectra of a 1000 W, quartz-halogen, tungsten coiled filament (FEL) lamp at different temperatures. The new model was tested with lamps of types FEL and 1000 W, 120 V quartz halogen (DXW). Comparisons with measurements of two national standards laboratories indicate that the model can account for the spectral irradiance values of lamps with an agreement better than 1% throughout the spectral region studied. We further demonstrate that the spectral irradiance of a lamp can be predicted with an expanded uncertainty of 2.6% if the color temperature and illuminance values for the lamp are known with expanded uncertainties of 20 K and 2%, respectively. In addition, it is suggested that the spectral irradiance may be derived from resistance measurements of the filament with lamp on and off.

Ojanen, Maija; Kaerhae, Petri; Ikonen, Erkki

2010-02-10T23:59:59.000Z

169

CALiPER Report 20.3: Robustness of LED PAR38 Lamps  

SciTech Connect

Three samples of 40 of the Series 20 PAR38 lamps underwent multi-stress testing, whereby samples were subjected to increasing levels of simultaneous thermal, humidity, electrical, and vibrational stress. The results do not explicitly predict expected lifetime or reliability, but they can be compared with one another, as well as with benchmark conventional products, to assess the relative robustness of the product designs. On average, the 32 LED lamp models tested were substantially more robust than the conventional benchmark lamps. As with other performance attributes, however, there was great variability in the robustness and design maturity of the LED lamps. Several LED lamp samples failed within the first one or two levels of the ten-level stress plan, while all three samples of some lamp models completed all ten levels. One potential area of improvement is design maturity, given that more than 25% of the lamp models demonstrated a difference in failure level for the three samples that was greater than or equal to the maximum for the benchmarks. At the same time, the fact that nearly 75% of the lamp models exhibited better design maturity than the benchmarks is noteworthy, given the relative stage of development for the technology.

Poplawski, Michael E.; Royer, Michael P.; Brown, Charles C.

2014-12-31T23:59:59.000Z

170

Table lamp with dynamically controlled lighting distribution and uniformly illuminated luminous shade  

DOE Patents (OSTI)

A double lamp table or floor lamp lighting system has a pair of compact fluorescent lamps (CFLs) or other lamps arranged vertically, i.e. one lamp above the other, with a reflective septum in between. By selectively turning on one or both of the CFLs, down lighting, up lighting, or both up and down lighting is produced. The control system can also vary the light intensity from each CFL. The reflective septum ensures that almost all the light produced by each lamp will be directed into the desired light distribution pattern which is selected and easily changed by the user. In a particular configuration, the reflective septum is bowl shaped, with the upper CFL sitting in the bowl, and a luminous shade hanging down from the bowl. The lower CFL provides both task lighting and uniform shade luminance. Planar compact fluorescent lamps, e.g. circular CFLs, particularly oriented horizontally, are preferable. CFLs provide energy efficiency. However, other types of lamps, including incandescent, halogen, and LEDs can also be used in the fixture. The lighting system may be designed for the home, hospitality, office or other environments.

Siminovitch, Michael J. (Pinole, CA); Page, Erik R. (Berkeley, CA)

2002-01-01T23:59:59.000Z

171

The evolving price of household LED lamps: Recent trends and historical comparisons for the US market  

SciTech Connect

In recent years, household LED light bulbs (LED A lamps) have undergone a dramatic price decline. Since late 2011, we have been collecting data, on a weekly basis, for retail offerings of LED A lamps on the Internet. The resulting data set allows us to track the recent price decline in detail. LED A lamp prices declined roughly exponentially with time in 2011-2014, with decline rates of 28percent to 44percent per year depending on lumen output, and with higher-lumen lamps exhibiting more rapid price declines. By combining the Internet price data with publicly available lamp shipments indices for the US market, it is also possible to correlate LED A lamp prices against cumulative production, yielding an experience curve for LED A lamps. In 2012-2013, LED A lamp prices declined by 20-25percent for each doubling in cumulative shipments. Similar analysis of historical data for other lighting technologies reveals that LED prices have fallen significantly more rapidly with cumulative production than did their technological predecessors, which exhibited a historical decline of 14-15percent per doubling of production.

Gerke, Brian F.; Ngo, Allison T.; Alstone, Andrea L.; Fisseha, Kibret S.

2014-10-14T23:59:59.000Z

172

A light diet for a giant appetite: An assessment of China's proposed fluorescent lamp standard  

SciTech Connect

Lighting has been one of the fastest growing electric end-uses in China over the last twenty years, with an average annual growth rate of 14%. Fluorescent lighting provides a significant portion of China's lighting need. In 1998, China produced 680 million fluorescent lamps, of which 420 million were linear fluorescent lamps of various diameters (T8 to T12). There are substantial variations both in energy efficiency and lighting performance among locally produced fluorescent lamps. Such variations present a perfect opportunity for policy intervention through efficiency standards to promote the adoption of more efficient fluorescent lamps in China. This paper analyzes China's proposed minimum efficiency standard for fluorescent lamps and presents an assessment of its likely impacts on China's lighting energy consumption and GHG emissions.

Lin, Jiang

2002-04-11T23:59:59.000Z

173

Methods for synthesizing alane without the formation of adducts and free of halides  

DOE Patents (OSTI)

A process is provided to synthesize an alane without the formation of alane adducts as a precursor. The resulting product is a crystallized .alpha.-alane and is a highly stable product and is free of halides.

Zidan, Ragaiy; Knight, Douglas A; Dinh, Long V

2013-02-19T23:59:59.000Z

174

CALiPER Report 21.3: Cost-Effectiveness of Linear (T8) LED Lamps  

SciTech Connect

Meeting performance expectations is important for driving adoption of linear LED lamps, but cost-effectiveness may be an overriding factor in many cases. Linear LED lamps cost more initially than fluorescent lamps, but energy and maintenance savings may mean that the life-cycle cost is lower. This report details a series of life-cycle cost simulations that compared a two-lamp troffer using LED lamps (38 W total power draw) or fluorescent lamps (51 W total power draw) over a 10-year study period. Variables included LED system cost ($40, $80, or $120), annual operating hours (2,000 hours or 4,000 hours), LED installation time (15 minutes or 30 minutes), and melded electricity rate ($0.06/kWh, $0.12/kWh, $0.18/kWh, or $0.24/kWh). A full factorial of simulations allows users to interpolate between these values to aid in making rough estimates of economic feasibility for their own projects. In general, while their initial cost premium remains high, linear LED lamps are more likely to be cost-effective when electric utility rates are higher than average and hours of operation are long, and if their installation time is shorter.

Miller, Naomi J.; Perrin, Tess E.; Royer, Michael P.

2014-05-27T23:59:59.000Z

175

Lamp system with conditioned water coolant and diffuse reflector of polytetrafluorethylene(PTFE)  

DOE Patents (OSTI)

A lamp system with a very soft high-intensity output is provided over a large area by water cooling a long-arc lamp inside a diffuse reflector of polytetrafluorethylene (PTFE) and titanium dioxide (TiO.sub.2) white pigment. The water is kept clean and pure by a one micron particulate filter and an activated charcoal/ultraviolet irradiation system that circulates and de-ionizes and biologically sterilizes the coolant water at all times, even when the long-arc lamp is off.

Zapata, Luis E. (Livermore, CA); Hackel, Lloyd (Livermore, CA)

1999-01-01T23:59:59.000Z

176

Is the light emitting diode (LED) an ultimate lamp?  

Science Journals Connector (OSTI)

Simple diagrams are used to show the transformation of a thin slab of intrinsic semiconductor (direct gap k elec =k hole ) from an ideal flat-band photopumped recombination-radiation light source into an ultimate lamp a pn junctionlight emitting diode(LED). A photoexcited intrinsic slab of semiconductor can be regarded as an ideal (flat-band) light source with however the photogenerated carriers and voltage available externally instead of as recombination radiation (light) if the slab is converted to half p type (one side) and half n type (the other side) i.e. to a pn junction. If an equal a bucking external voltage is applied resulting in an input current when the photoexcitation is removed the slab becomes again (remains) an ideal flat-band light source a pn junctionLED. In practice the LED takes the form of a pn heterostructure in order to improve electronhole injection reduce the absorption of recombination radiation and to make possiblewith proper geometriesimproved photon escape.

N. Holonyak Jr.

2000-01-01T23:59:59.000Z

177

Integrated starting and running amalgam assembly for an electrodeless fluorescent lamp  

DOE Patents (OSTI)

An integrated starting and running amalgam assembly for an electrodeless SEF fluorescent lamp includes a wire mesh amalgam support constructed to jointly optimize positions of a starting amalgam and a running amalgam in the lamp, thereby optimizing mercury vapor pressure in the lamp during both starting and steady-state operation in order to rapidly achieve and maintain high light output. The wire mesh amalgam support is constructed to support the starting amalgam toward one end thereof and the running amalgam toward the other end thereof, and the wire mesh is rolled for friction-fitting within the exhaust tube of the lamp. The positions of the starting and running amalgams on the wire mesh are jointly optimized such that high light output is achieved quickly and maintained, while avoiding any significant reduction in light output between starting and running operation.

Borowiec, Joseph Christopher (Schenectady, NY); Cocoma, John Paul (Clifton Park, NY); Roberts, Victor David (Burnt Hills, NY)

1998-01-01T23:59:59.000Z

178

LED Linear Lamps and Troffer Lighting: CALiPER Report Series 21  

Energy.gov (U.S. Department of Energy (DOE))

View the video about CALiPER Report Series 21 on LED Linear Lamps and Troffer Lighting, featuring interviews with Tracy Beeson and Naomi Miller of Pacific Northwest National Laboratory.

179

DOE Publishes CALiPER Report on Lumen and Chromaticity Maintenance of LED PAR38 Lamps  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of Energy's CALiPER program has released Report 20.4, which is part of a series of investigations on LED PAR38 lamps. Report 20.4 focuses on lumen maintenance, chromaticity...

180

DOE Publishes CALiPER Snapshot Report on LED A Lamps  

Energy.gov (U.S. Department of Energy (DOE))

DOE's CALiPER program has released a Snapshot Report on LED A lamps, which utilizes the LED Lighting Facts program's extensive product database to help industry stakeholders understand the current state and trajectory of the market for that class

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

DOE Publishes New CALiPER Report on Subjective Evaluation of LED PAR38 Lamps  

Energy.gov (U.S. Department of Energy (DOE))

DOE has published the first in a series of four special investigations intended to extend the findings of CALiPER Application Summary Report 20: LED PAR38 Lamps, which was published late last year.

182

Text-Alternative Version: CALiPER Report Series 20 on LED PAR38 Lamps  

Energy.gov (U.S. Department of Energy (DOE))

Michael Royer, Lighting Engineer, Pacific Northwest National Laboratory: The CALiPER program looks at typical LED lamp performance attributes. As we've gone through the progression of reports, we...

183

MISSION CATHODIQUE A L'INTRIEUR DES LAMPES A INCANDESCENCE ; par M. L. HOULLEVIGUE (1).  

E-Print Network (OSTI)

523 ?MISSION CATHODIQUE A L'INT?RIEUR DES LAMPES A INCANDESCENCE ; par M. L. HOULLEVIGUE (1). I. Lorsqu'on survolte fortement une lampe à incandescence à filament de charbon, par exemple en mettant sous incandescent. ' , Fic.. 1. Tous ces effets peuvent être attribués, en première analyse, aux électrons émanés du

Boyer, Edmond

184

ISSUANCE 2015-01-26: Energy Conservation Program: Energy Conservation Standards for High-Intensity Lamps, Notice to Reopen Comment Period  

Energy.gov (U.S. Department of Energy (DOE))

Energy Conservation Program: Energy Conservation Standards for High-Intensity Lamps, Notice to Reopen Comment Period

185

Demonstration of LED Retrofit Lamps at the Jordan Schnitzer Museum of Art  

SciTech Connect

The Jordan Schnitzer Museum of Art in Eugene, Oregon, houses a remarkable permanent collection of Asian art and antiquities, modern art, and sculpture, and also hosts traveling exhibitions. In the winter and spring of 2011, a series of digital photographs by artist Chris Jordan, titled "Running the Numbers," was exhibited in the Coeta and Donald Barker Special Exhibitions Gallery. These works graphically illustrate waste (energy, money, health, consumer objects, etc.) in contemporary culture. The Bonneville Power Administration and the Eugene Water and Electricity Board provided a set of Cree 12W light-emitting diode (LED) PAR38 replacement lamps (Cree LRP38) for the museum to test for accent lighting in lieu of their standard Sylvania 90W PAR38 130V Narrow Flood lamps (which draw 78.9W at 120V). At the same time, the museum tested LED replacement lamps from three other manufacturers, and chose the Cree lamp as the most versatile and most appropriate color product for this exhibit. The lamps were installed for the opening of the show in January 2011. This report describes the process for the demonstration, the energy and economic results, and results of a survey of the museum staff and gallery visitors on four similar clusters of art lighted separately by four PAR38 lamps.

Miller, Naomi J.

2011-09-01T23:59:59.000Z

186

Bottom-Up Energy Analysis System - Methodology and Results  

E-Print Network (OSTI)

Documents U.S. Rulemaking Documents TSL 4 PHP IncandescentLamps Incandescent Lamps Fluorescent Lamp Ballasts kWh/yrand T5 fluorescent tubes, incandescent lamps, CFLs, Halogen

McNeil, Michael A.

2013-01-01T23:59:59.000Z

187

2014-10-14 Issuance: Test Procedures Correction for Fluorescent...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

10-14 Issuance: Test Procedures Correction for Fluorescent Lamp Ballasts; Notice of Proposed Rulemaking 2014-10-14 Issuance: Test Procedures Correction for Fluorescent Lamp...

188

DSM Electricity Savings Potential in the Buildings Sector in APP Countries  

E-Print Network (OSTI)

150 million compact fluorescent light bulbs in 2010. (ChinaCleaners Incandescent Bulbs Fluorescent Lamps Ballasts forincandescent bulbs with compact fluorescent lamps. Consumers

McNeil, MIchael

2011-01-01T23:59:59.000Z

189

Optical properties of lanthanide-containing halide-modified zinc tellurite glasses  

SciTech Connect

As part of an ongoing investigation to characterize the properties and structure of Zn halide-Te oxide glasses, we report preliminary measurements of the optical properties of several Nd- and Er-doped tellurites. Measurements include fluorescence lifetimes and estimates of the theoretical radiative lifetimes (from traditional Judd-Ofelt analysis of optical absorption spectra) as well as phonon sideband studies sensitive to vibrational characteristics near the rare earth ion. Response of these optical features to the substitution of alternative halides is examined.

Sidebottom, D.L.; Hruschka, M.A. [New Mexico Univ., Albuquerque, NM (United States); Potter, B.G.; Brow, R.K.; Hudgens, J.J. [Sandia National Labs., Albuquerque, NM (United States)

1996-12-31T23:59:59.000Z

190

BEFORE THE U.S. DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Engineered Products Company Engineered Products Company (metal halide lamp fixtures) ) ) ) ) ) Case Number: 2012-SE-5401 Issued: July 26, 2012 NOTICE OF NONCOMPLIANCE DETERMINATION Metal halide lamp fixtures are covered products subject to federal energy conservation standards as described in 42 U.S.C. §§ 6292(a)(l9), 6295(hh) and 10 C.P.R. § 431.326. Manufacturers and private labelers are prohibited from distributing covered products that do not comply with the applicable conservation standards. 10 C.P.R.§ 429.102(a)(6); 42 U.S.C. § 6302(a)(5). Engineered Products Company ("EPCO") notified the U.S. Department of Energy ("DOE") that EPCO had distributed in commerce 19 units of basic modell5701, which has a ballast efficiency of less than 94%. FINDINGS

191

Energy-Efficient, High-Color-Rendering LED Lamps Using Oxyfluoride and Fluoride Phosphors  

SciTech Connect

LED lamps using phosphor downconversion can be designed to replace incandescent or halogen sources with a 'warm-white' correlated color temperature (CCT) of 2700-3200 K and a color rendering index (CRI) greater than 90. However, these lamps have efficacies of {approx}70% of standard 'cool-white' LED packages (CCT = 4500-6000 K; CRI = 75-80). In this report, we describe structural and luminescence properties of fluoride and oxyfluoride phosphors, specifically a (Sr,Ca){sub 3}(Al,Si)O{sub 4}(F,O):Ce{sup 3+} yellow-green phosphor and a K{sub 2}TiF{sub 6}:Mn{sup 4+} red phosphor, that can reduce this gap and therefore meet the spectral and efficiency requirements for high-efficacy LED lighting. LED lamps with a warm-white color temperature (3088 K), high CRI (90), and an efficacy of {approx}82 lm/W are demonstrated using these phosphors. This efficacy is {approx}85% of comparable cool-white lamps using typical Y{sub 3}Al{sub 5}O{sub 12}:Ce{sup 3+}-based phosphors, significantly reducing the efficacy gap between warm-white and cool-white LED lamps that use phosphor downconversion.

Setlur, A.; Radkov, E; Henderson, C; Her, J; Srivastava, A; Karkada, N; Kishore, M; Kumar, N; Aesram, D; et al.

2010-01-01T23:59:59.000Z

192

DOE Publishes Notice of Public Meeting and Availability of the Framework Document for General Service Lamps Energy Conservation Standards  

Energy.gov (U.S. Department of Energy (DOE))

The Department of Energy has published a Federal Register notice of public meeting and availability of the framework document regarding energy conservation standards for general service lamps.

193

Selective Solid-Liquid Extraction of Lithium Halide Salts Using a Ditopic Macrobicyclic Receptor  

E-Print Network (OSTI)

pairs. The receptor can transport these salts from an aqueous phase through a liquid organic membrane and membrane transport, almost all reported efforts have focused on the transfer of lithium salts from this by binding the salts as contact ion pairs. Receptor 1 can also transport alkali metal halide salts out

Smith, Bradley D.

194

Transport of Alkali Halides through a Liquid Organic Membrane Containing a Ditopic Salt-Binding Receptor  

E-Print Network (OSTI)

in the solid state as contact ion pairs. Transport experiments, using a supported liquid membrane and high saltTransport of Alkali Halides through a Liquid Organic Membrane Containing a Ditopic Salt and anion receptors. All transport systems exhibit the same qualitative order of ion selectivity; that is

Smith, Bradley D.

195

Csp3Csp3 Homocoupling Reaction of Benzyl Halides Catalyzed by Rhodium  

Science Journals Connector (OSTI)

A highly reactive alkylrhodium complex was formed from Me2Zn and RhCl(PPh3)3 and effectively catalyzed a Csp3Csp3 homocoupling reaction of benzyl halides. A Csp3Csp3 coupling reaction using Rh catalyst has not been reported up to now. The reaction ...

Kazuyuki Sato; Yuichi Inoue; Tomohisa Mori; Atsushi Sakaue; Atsushi Tarui; Masaaki Omote; Itsumaro Kumadaki; Akira Ando

2014-06-30T23:59:59.000Z

196

Low pressure vinylation of aryl and vinyl halides via HeckMizoroki reactions using ethylene  

E-Print Network (OSTI)

Low pressure vinylation of aryl and vinyl halides via Heck­Mizoroki reactions using ethylene Craig with ethylene under ambient pressure (15­30 psi) to give the corresponding vinylarenes. The reactions work of ethylene) of functionalized vinylarenes and 1,3-di- enes.4 When fully developed, we hope, many

RajanBabu, T. V. "Babu"

197

Dramatic Acceleration of the Menschutkin Reaction and Distortion of Halide Leaving-Group Order  

E-Print Network (OSTI)

-butylbenzyl halides are 4-t-BuBnCl (62 000 M) > 4-t-BuBnBr (2200 M) > 4-t-BuBnI (35 M); thus, the free energy.; Sola, M. H. In Progress in Physical Organic Chemistry; Taft, R. W., Ed.; Wiley: New York, 1993; Vol. 19

Smith, Bradley D.

198

Whitesides et al. f Reaction ctfAlkyl Halides with Magnesiunt Mechanismof Formationof GrignardReagents.  

E-Print Network (OSTI)

carbanionsand carbonium ionsare not intermediates,and tliat the transition-itut. structuredoesnot resemblean SN2.rnagncsiumatom at the mctal surface(or possibly in solution) rrrrghtdisplacehelidefrotncarbonin an SN2-likc rcuctionor inrcrlWhitesides et al. f Reaction ctfAlkyl Halides with Magnesiunt Mechanismof Formationof Grignard

Prentiss, Mara

199

L-Prize Competition Winner 60W Incandescent Replacement Lamp Update  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interagency Technology Deployment Working Group L Prize ® Competition Winner 60W Incandescent Replacement Lamp Update James E. Rannels, Senior Advisor L Prize Competition D&R International March 15, 2012 Cost of electricity 1 cent per kilowatt-hour The Washington Post, March 8, 2012 Page One 2 Cost of electricity 11 cents per kilowatt-hour The Washington Post, March 9, 2012 Page Two 3 What Is the L Prize? * Technology competition to spur innovation and exceptional performance * Created by Energy Independence and Security Act (EISA 2007) Sec. 655 * Two key lamp replacements: 60W Incandescent and PAR 38 Halogen * Future focus: 21 st Century Lamp * Cash prizes, federal purchasing, utility programs 4 Philips Wins First L Prize * August 3, 2011: Philips

200

L-Prize Competition Winner 60W Incandescent Replacement Lamp Update  

NLE Websites -- All DOE Office Websites (Extended Search)

Interagency Technology Deployment Working Group L Prize ® Competition Winner 60W Incandescent Replacement Lamp Update James E. Rannels, Senior Advisor L Prize Competition D&R International March 15, 2012 Cost of electricity 1 cent per kilowatt-hour The Washington Post, March 8, 2012 Page One 2 Cost of electricity 11 cents per kilowatt-hour The Washington Post, March 9, 2012 Page Two 3 What Is the L Prize? * Technology competition to spur innovation and exceptional performance * Created by Energy Independence and Security Act (EISA 2007) Sec. 655 * Two key lamp replacements: 60W Incandescent and PAR 38 Halogen * Future focus: 21 st Century Lamp * Cash prizes, federal purchasing, utility programs 4 Philips Wins First L Prize * August 3, 2011: Philips

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Pump-lamp firing-pulse generator for solid-state lasers  

SciTech Connect

This paper describes a generator that provides, with maximum output-pulse amplitude, sequential or external firing of four INP16/250 (IFP-8000) lamps at a frequency of 1 Hz. The energy and time characteristics of the generator are improved as compared with similar devices, which provides a time instability of the delay between a generator-trigger pulse and the optical pumping pulse of + or - 1 usec. The output-pulse amplitude can be varied according to the type and number of lamps fired. Measures are taken to reduce the supply noise produced in firing-pulse generation and to increase the operating safety of the device.

Denishchik, Y.S.

1985-12-01T23:59:59.000Z

202

The Fuzzy Design of the Intelligent System for the Energy-Saving Lamps  

Science Journals Connector (OSTI)

In the paper, a intelligent system was proposed. It consists of variable converter and intelligent controller. Variable reactor which concludes variable reactance converter and power converter has wide applications in the soft starting, speed controlling ... Keywords: fuzzy control, variable reactor, intelligent control, power converter, Energy-Saving Lamps

Youxin Yuan; Kaihua Cui; Yiping Xiao; Tieliang Xu

2008-12-01T23:59:59.000Z

203

RF driven sulfur lamp having driving electrodes which face each other  

DOE Patents (OSTI)

A high intensity discharge lamp without mercury is disclosed radiating a selected spectrum of which can be almost entirely in the visible range from an envelope that contains a sulfur containing substance. The lamp utilizes a signal source that generates an excitation signal that is externally coupled to the exterior surface of the envelope to excite the enclosed sulfur containing substance. Various embodiments of the lamp use electrodes adjacent the envelope to couple the excitation signal thereto with the face of the electrodes shaped to complement the shape of the exterior surface of the envelope. Two shapes discussed are spherical and cylindrical. To minimize filamentary discharges each envelope may include an elongated stem affixed to the exterior thereof whereby a rotational subsystem spins the envelope. In yet another embodiment the envelope has a Dewar configuration with two electrodes, one positioned near the external curved side surface of the body, and a second to the inner surface of the hole through the envelope. Further, the envelope may contain a backfill of a selected inert gas to assist in the excitation of lamp with that backfill at a pressure of less than 1 atmosphere, wherein the backfill pressure is directly related to the increase or decrease of peak output and inversely related to the increase and decrease of the emitted spectrum from the envelope. The emitting fill can be less than 6 mg/cc, or at least 2 mg/cc of the envelope of a sulfur containing substance. 17 figs.

Gabor, G.; Orr, T.R.; Greene, C.M.; Crawford, D.G.; Berman, S.M.

1999-06-22T23:59:59.000Z

204

15 KJ FLASH LAMP, POWER CONDITIONING UNIT DESIGNED FOR SAFTY, RELIABILITY & MANUFACTURABILITY*  

SciTech Connect

A 15kJoule, Flash Lamp Power Conditioning Unit has been successfully designed, developed, and deployed in the National Ignition Facility (NIF) Preamplifier Modules (PAM). The primary design philosophy of this power conditioning unit (PCU) is safety, reliability, and manufacturability. Cost reduction over commercially equivalent systems was also achieved through an easily manufactured packaging design optimized to meet NIF requirements. While still maintaining low cost, the PCU design includes a robust control system, fault diagnostic system, and safety features. The pulsed power design includes 6 PFN modules, each including a dual series injection trigger transformer, that drive a total of 12 flash lamp loads. The lamps are individually triggered via a 20kV pulse produced by a 1kV, MCT switched capacitive discharge unit on the primary side of the trigger transformer. The remote control interface includes an embedded controller that captures flash lamp current wave forms and fault status for each shot. The embedded controller provides the flexibility of remotely adjusting both the main drive voltage from 1.6 to 2.5 kV and the trigger voltage from 0 to 20 kV.

James, G; Merritt, B; Dreifuerst, G; Strickland, S

2007-08-07T23:59:59.000Z

205

Laboratory for Advanced Materials Processing University of Maryland http://www.enma.umd.edu/LAMP  

E-Print Network (OSTI)

) = Rs x (L / W), with Rs: sheet resistance of a layer of this material The sheet resistance is expressedLaboratory for Advanced Materials Processing � University of Maryland http Operating Procedure for LAMP four point probe sheet resistance measurements Overview of 4 point probe

Rubloff, Gary W.

206

Report 20.3: Stress Testing of LED PAR38 Lamps  

Energy.gov (U.S. Department of Energy (DOE))

A small sample of each of the Application Summary Report 20 PAR38 lamp types underwent stress testing that included substantial temperature and humidity changes, electrical variation, and vibration. The results do not directly address expected lifetime, but can be compared with one another, as well as with benchmark conventional products, to assess the relative robustness of the product designs. (24 pages, December 2014)

207

Method and apparatus for powering an electrodeless lamp with reduced radio frequency interference  

DOE Patents (OSTI)

An electrodeless lamp waveguide structure includes tuned absorbers for spurious RF signals. A lamp waveguide with an integral frequency selective attenuation includes resonant absorbers positioned within the waveguide to absorb spurious out-of-band RF energy. The absorbers have a negligible effect on energy at the selected frequency used to excite plasma in the lamp. In a first embodiment, one or more thin slabs of lossy magnetic material are affixed to the sidewalls of the waveguide at approximately one quarter wavelength of the spurious signal from an end wall of the waveguide. The positioning of the lossy material optimizes absorption of power from the spurious signal. In a second embodiment, one or more thin slabs of lossy magnetic material are used in conjunction with band rejection waveguide filter elements. In a third embodiment, one or more microstrip filter elements are tuned to the frequency of the spurious signal and positioned within the waveguide to couple and absorb the spurious signal's energy. All three embodiments absorb negligible energy at the selected frequency and so do not significantly diminish the energy efficiency of the lamp.

Simpson, James E. (Gaithersburg, MD)

1999-01-01T23:59:59.000Z

208

Method and apparatus for powering an electrodeless lamp with reduced radio frequency interference  

DOE Patents (OSTI)

An electrodeless lamp waveguide structure includes tuned absorbers for spurious RF signals. A lamp waveguide with an integral frequency selective attenuation includes resonant absorbers positioned within the waveguide to absorb spurious out-of-band RF energy. The absorbers have a negligible effect on energy at the selected frequency used to excite plasma in the lamp. In a first embodiment, one or more thin slabs of lossy magnetic material are affixed to the sidewalls of the waveguide at approximately one quarter wavelength of the spurious signal from an end wall of the waveguide. The positioning of the lossy material optimizes absorption of power from the spurious signal. In a second embodiment, one or more thin slabs of lossy magnetic material are used in conjunction with band rejection waveguide filter elements. In a third embodiment, one or more microstrip filter elements are tuned to the frequency of the spurious signal and positioned within the waveguide to couple and absorb the spurious signal's energy. All three embodiments absorb negligible energy at the selected frequency and so do not significantly diminish the energy efficiency of the lamp. 18 figs.

Simpson, J.E.

1999-06-08T23:59:59.000Z

209

Predicted Pulsed-Power/Flash-Lamp Performance of the NIF Main Amplifier  

SciTech Connect

The laser glass for the National Ignition Facility (NIF) Main Amplifier system is pumped by a system of 192 pulsed power/flash lamp assemblies. Each of these 192 assemblies consists of a 1.6 MJ (nominal) capacitor bank working with a Pre-Ionization/Lamp Check (PILC) pulser to drive an array of 40 flash lamps. This paper describes the predicted performance of these Power Conditioning System (PCS) modules in concert with flashlamp assemblies in NIF. Each flashlamp assembly consists of 20 parallel sets of lamps in series pairs. The sensitivity of system performance to various design parameters of the PILC pulser and the main capacitor bank is described. Results of circuit models are compared to sub-scale flashlamp tests and to measurements taken in tests of a PCS module driving a flashlamp assembly in the First Article NIF Test Module facility at Sandia National Laboratories. Also included are predictions from a physics-based, semi-empirical amplifier gain code.

Fulkerson, E. Steven; Hammond, Jud; Harjes, Henry C.; Moore, William B.S.; Smith, David L.; Wilson, J. Michael

1999-06-22T23:59:59.000Z

210

Issues, Models and Solutions for Triac Modulated Phase Dimming of LED Lamps  

E-Print Network (OSTI)

greater than incandescent lamps [1,2]. In fact, recent technological breakthroughs [3-7] in the high of LED lighting: An incandescent source produces 10 ­ 20 lumens/watt, while several manufacturers have? Incandescent bulbs primarily utilize phase modulating dimming through triac switches to control the power sent

Lehman, Brad

211

Hands On Science with NOAA TITLE: Plate Tectonics and Lava Lamps  

E-Print Network (OSTI)

and geological events?" Answer = heat from radioactive decay · Compare the light bulb in lava to Earth's internal in the lava lamp. · Plot recent earthquakes and volcanic activity on a world map and compare to the location.education.noaa.gov/Ocean_and_Coasts/Ocean_Floor_Features.html USGS Earthquake Hazards - http

212

Adsorbate-induced corrosion: anodic dissolution of palladium induced by chemisorbed iodine in halide-free acid solutions  

E-Print Network (OSTI)

ADSORBATE-INDUCED CORROSION: ANODIC DISSOLUTION OF PALLADIUM INDUCED BY CHEMISORBED IODINE IN HALIDE-FREE ACID SOLUTIONS A Thesis JANEMARIE A. SCHIMPF Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE December 1991 Major Subject: Chemistry ADSORBATE-INDUCED CORROSION: ANODIC DISSOLUTION OF PALLADIUM INDUCED BY CHEMISORBED IODINE IN HALIDE-FREE ACID SOLUTIONS A Thesis JANEMARIE A. SCHIMPF Approved...

Schimpf, Janemarie A

2012-06-07T23:59:59.000Z

213

Stability diagrams for fourfold coordination of polyvalent metal ions in molten mixtures of halide salts  

SciTech Connect

The stability of local fourfold coordination for divalent and trivalent metal ions in liquid mixtures of polyvalent metal halides and alkali halides is classified by means of structural coordinates obtained from properties of the elements. In parallel with earlier classifications of compound crystal structures and molecular shapes, the elemental properties are taken from first-principles calculations of valence electron orbitals in atoms, in the form of (i) the nodal radii of Andreoni, Baldereschi and Guizzetti or (ii) the pseudopotential radii or Zunger and Cohen. As a third alternative a classification based on Pettifor's phenomenological chemical scale of the elements is also considered. The alternative structural classification schemes that are developed from these elemental properties are generally successfully in distinguishing molten mixtures in which the available experimental evidence indicates long-lived fourfold coordination of polyvalent metal ions. In addition, Pettifor's chemical scale scheme is useful in sorting out finer details of local coordination in the liquid state. 3 figs., 71 refs.

Akdeniz, Z. (International Centre for Theoretical Physics, Trieste (Italy) Istanbul Univ. (Turkey). Dept. of Physics); Tosi, M.P. (Trieste Univ. (Italy). Dipt. di Fisica Teorica Argonne National Lab., IL (USA))

1988-11-01T23:59:59.000Z

214

Enhancing the Sensitivity of Chemical Sensors for Chlorinated Hydrocarbons in Water by the Use of Tapered Silver Halide Fibers and Tunable Diode Lasers  

Science Journals Connector (OSTI)

Tapered silver halide fibers were used for the first time for high-sensitivity fiber evanescent wave spectroscopic (FEWS) measurements of chlorinated hydrocarbons (CHCs) in water at...

Gbel, Roman; Krska, Rudolf; Kellner, Robert; Kastner, Joachim; Lambrecht, Armin; Tacke, Maurus; Katzir, Abraham

1995-01-01T23:59:59.000Z

215

Energy Savings and NOx Emissions Reduction Potential from the 2012 Federal Legislation to Phase Out Incandescent Lamps in Texas  

E-Print Network (OSTI)

Lamps in Texas Description Value Reference Total Housing Units in Texas in 2013: 10,204,056 Real Estate Center, Texas A&M University3, U.S. Census Bureau4 5 Average Lighting Electricity Usage per House: 1,946 kWh/yr NREL Building America Program6... Savings in Texas: 10,424,973 MWh/yr OSD CFL Savings in Texas: 28,562 MWh/day By 2013, it is estimated that total savings of 10,424,973 MWh/yr would be achieved from replacing incandescent lamps with compact fluorescent lamps (CFL) in residential...

Liu, Zi; Baltazar, Juan Carlos; Haberl, Jeff; Soman, Rohit

216

LED lamp or bulb with remote phosphor and diffuser configuration with enhanced scattering properties  

DOE Patents (OSTI)

An LED lamp or bulb is disclosed that comprises a light source, a heat sink structure and an optical cavity. The optical cavity comprises a phosphor carrier having a conversions material and arranged over an opening to the cavity. The phosphor carrier comprises a thermally conductive transparent material and is thermally coupled to the heat sink structure. An LED based light source is mounted in the optical cavity remote to the phosphor carrier with light from the light source passing through the phosphor carrier. A diffuser dome is included that is mounted over the optical cavity, with light from the optical cavity passing through the diffuser dome. The properties of the diffuser, such as geometry, scattering properties of the scattering layer, surface roughness or smoothness, and spatial distribution of the scattering layer properties may be used to control various lamp properties such as color uniformity and light intensity distribution as a function of viewing angle.

Tong, Tao; Le Toquin, Ronan; Keller, Bernd; Tarsa, Eric; Youmans, Mark; Lowes, Theodore; Medendorp, Jr., Nicholas W; Van De Ven, Antony; Negley, Gerald

2014-11-11T23:59:59.000Z

217

Xenon flash lamp pumped self-frequency doubling NYAB pulsed laser  

Science Journals Connector (OSTI)

Neodymium doped yttrium aluminum borate (NYAB) crystals with sizes up to 45mm have been grown successfully. NYAB rod of 4 ? 12mm was pumped by xenon flash lamp, and several mJ of 0.53?m green laser output was obtained. The oscillation threshold, the pulse duration, the laser beam polarization, and the laser beam divergence were measured to be 78mJ, 100ns, 90% and 2mrad, respectively.

Luo Zundu; Jiang Aidong; Huang Yichuan; Qiu Minwang

1989-01-01T23:59:59.000Z

218

Household Light Makes Global Heat: High Black Carbon Emissions From Kerosene Wick Lamps  

Science Journals Connector (OSTI)

(3) Lighting is another component of this household energy challenge, with millions of households still relying on simple liquid-fueled lamps, but little is known of the associated environmental and health impacts. ... For laboratory tests, CO2 and CO concentrations were measured in real-time with a Li-COR 6252 (Li-COR Biosciences, Lincoln, NE) and Horiba AIA-220 (Horiba, Kyoto, Japan) nondispersive infrared (NDIR) analyzer, respectively. ...

Nicholas L. Lam; Yanju Chen; Cheryl Weyant; Chandra Venkataraman; Pankaj Sadavarte; Michael A. Johnson; Kirk R. Smith; Benjamin T. Brem; Joseph Arineitwe; Justin E. Ellis; Tami C. Bond

2012-11-19T23:59:59.000Z

219

Creating markets for new products to replace incandescent lamps: The international experience  

SciTech Connect

Since the summer of 1995, several organizations have been in pursuit of what many consider the Holy Grail of lighting technology--a low-cost, drop-in, energy-efficient replacement for the incandescent lamp. This paper summarizes the international experience in attempting to catalyze the commercialization of a mass-market, replacement product that could have major impact on residential lighting energy consumption in US and EU homes. The technology procurement effort was originally spearheaded by US Federal Government through a loose collaboration between the Department of Defense (DoD), the Environmental Protection Agency (EPA) and the Department of Energy (DOE). The DoD agreed to serve as the anchor buyer for a low-cost, drop-in replacement product for standard-sized light bulbs that provide at least 30 percent energy savings compared to traditional incandescent lamps. In parallel to the US effort, the International Energy Agency launched a co-operative technology procurement effort by assembling large buyers' groups in Finland, the Netherlands, Sweden, and the United Kingdom to pull a similar efficient lighting product into the European market. The lukewarm response from lamp manufacturers to these two technology procurement efforts illustrates the challenges of transforming residential lighting from incandescent to efficient lighting.

Rubinstein, F.; Borg, N.; Horowitz, N.; Narel, T.; Morehouse, E.T. Jr.

1998-07-01T23:59:59.000Z

220

Performance of a novel LED lamp arrangement to reduce SNR fluctuation for multi-user visible light communication systems  

Science Journals Connector (OSTI)

This paper investigates the performance of our recently proposed LED lamp arrangement to reduce the SNR fluctuation from different locations in the room for multi-user visible light...

Wang, Zixiong; Yu, Changyuan; Zhong, Wen-De; Chen, Jian; Chen, Wei

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

MMPA - Commercial and Industrial Energy Efficiency Program | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

MMPA - Commercial and Industrial Energy Efficiency Program MMPA - Commercial and Industrial Energy Efficiency Program MMPA - Commercial and Industrial Energy Efficiency Program < Back Eligibility Commercial Industrial Savings Category Appliances & Electronics Commercial Lighting Lighting Manufacturing Maximum Rebate In no case will rebates exceed the purchase price of equipment; maximum rebates are set by participating cities Program Info State Minnesota Program Type Utility Rebate Program Rebate Amount Motor (Upgrade): $20 - $22/HP Variable Frequency Drive: $35/HP Vending Machine Controller: $50 Lighting Retrofit Fluorescent T5-T8 Lamps (Electronic Ballast): $1 - $26 High Bay Fluorescent Fixtures (Electronic Ballast): $85 - $160 Compact Fluorescent Fixtures: $2 - $26 High Pressure Sodium Fixtures: $30 - $50 Ceramic Metal Halide Fixtures: $20 - $100

222

A New Rb Lamp Exciter Circuit for Rb atomic clocks and Studies on Transition from Ring to Red mode  

E-Print Network (OSTI)

In this paper we describe the development of novel RF exciter circuit for electrode less Rb lamp. The lamp exciter circuit is a RF oscillator with a a new configuration operating at 60 to 65 MHz frequency with 3 to 4 watt power. The Rb lamp is used in exciting the ground state hyperfine transitions in Rb atom in a glass cell placed inside a tuned microwave cavity, As the frequency of these hyperfine transitions is very stable it is used in the development of Rb atomic clock by phase locking the oven controlled crystal oscillator (OCXO) to this atomic transition frequency. The details of the Rb lamp exciter are presented in the paper.The Lamp is ideally operated in ring mode as in this mode the linewidth is narrow and there is no self reversal. However, high temperature and RF excitation power may drive the Rb lamp to red mode which gives rise to line broadening and self reversal. It is the experience that mode change from ring to red deteriorates the atomic signal strength and S/N. In this paper the reasons of mode change are also discussed.

Savita Singh; Bikash Ghosal; G M Saxena

2010-11-10T23:59:59.000Z

223

Nucleophilic vinylic substitutions of (Z)-(2-aroyloxyvinyl)phenyl-?3-iodanes with tetrabutylammonium halides: vinylic SN2 reactions and ligand coupling on iodine(III)  

Science Journals Connector (OSTI)

Treatment of (Z)-(?-benzoyloxyvinyl)phenyl-?3-iodanes, readily prepared from ethynyl(phenyl)(tetrafluoroborato)-?3-iodane via stereoselective Michael-type addition of benzoic acids in methanol in the presence of sodium benzoates, with tetrabutylammonium halides in THF at 65C results in a vinylic SN2 reaction to give the inverted (E)-?-benzoyloxyvinyl halides in high yields.

Masahito Ochiai; Yoshio Nishi; Masaya Hirobe

2005-01-01T23:59:59.000Z

224

Advances in the growth of alkaline-earth halide single crystals for scintillator detectors  

SciTech Connect

Alkaline-earth scintillators such as strontium iodide and other alkaline-earth halides activated with divalent europium represent some of the most efficient and highest energy resolution scintillators for use as gamma-ray detectors in a wide range of applications. These applications include the areas of nuclear nonproliferation, homeland security, the detection of undeclared nuclear material, nuclear physics and materials science, medical diagnostics, space physics, high energy physics, and radiation monitoring systems for first responders, police, and fire/rescue personnel. Recent advances in the growth of large single crystals of these scintillator materials hold the promise of higher crystal yields and significantly lower detector production costs. In the present work, we describe new processing protocols that, when combined with our molten salt filtration methods, have led to advances in achieving a significant reduction of cracking effects during the growth of single crystals of SrI2:Eu2+. In particular, we have found that extended pumping on the molten crystal-growth charge under vacuum for time periods extending up to 48 hours is generally beneficial in compensating for variations in the alkaline-earth halide purity and stoichiometry of the materials as initially supplied by commercial sources. These melt-pumping and processing techniques are now being applied to the purification of CaI2:Eu2+ and some mixed-anion europium-doped alkaline-earth halides prior to single-crystal growth by means of the vertical Bridgman technique. The results of initial studies of the effects of aliovalent doping of SrI2:Eu2+ on the scintillation characteristics of this material are also described.

Boatner, Lynn A [ORNL; Ramey, Joanne Oxendine [ORNL; Kolopus, James A [ORNL; Neal, John S [ORNL; Cherepy, Nerine [Lawrence Livermore National Laboratory (LLNL); Payne, Stephen A. [Lawrence Livermore National Laboratory (LLNL); Beck, P [Lawrence Livermore National Laboratory (LLNL); Burger, Arnold [Fisk University, Nashville; Rowe, E [Fisk University, Nashville; Bhattacharya, P. [Fisk University, Nashville

2014-01-01T23:59:59.000Z

225

Understanding the effect of halide poisoning in CO oxidation over Au/TiO[subscript 2  

SciTech Connect

The effect of halide poisoning of Au/TiO{sub 2} catalysts in low temperature CO oxidation was investigated using bromide as the poison and a combination of X-ray absorption spectroscopy (XANES and EXAFS), quantitative CO adsorption, and catalytic measurements. It was found that halide prevented full reduction of cationic Au by displacing oxyhydroxy ligands and remaining bound to Au during low temperature reduction, causing a reduction in catalytic activity. On reduced Au samples, bromide (likely as NaBr molecule) was preferentially adsorbed on Au and not on TiO{sub 2}, and suppressed both the adsorption of CO and the catalytic activity. At low Br contents, each adsorbed Br suppressed adsorption of three CO, suggesting that Br was adsorbed on three-fold sites but the effect decreased with increasing Br content possibly due to crowding of adsorbed Br. When 5--10% of the Au was bound to Br, the catalytic activity was completely blocked, although {approx}35% of the original CO adsorption capacity remained. The data suggest that not all CO adsorption sites are catalytic active sites, and are consistent with the perimeter Au atoms at/near the particle-support interface (perimeter) being active sites.

Oxford, S.M.; Henao, J.D.; Yang, J.H.; Kung, M.C.; Kung, H.H. (NWU)

2008-07-08T23:59:59.000Z

226

Transition metal ion-assisted photochemical generation of alkyl halides and hydrocarbons from carboxylic acids  

SciTech Connect

Near-UV photolysis of aqueous solutions of propionic acid and aqueous Fe3+ in the absence of oxygen generates a mixture of hydrocarbons (ethane, ethylene and butane), carbon dioxide, and Fe2+. The reaction becomes mildly catalytic (about five turnovers) in the presence of oxygen which converts a portion of alkyl radicals to oxidizing intermediates that reoxidize Fe2+. The photochemistry in the presence of halide ions (X? = Cl?, Br?) generates ethyl halides via halogen atom abstraction from FeXn3?n by ethyl radicals. Near-quantitative yields of C2H5X are obtained at ?0.05 M X?. Competition experiments with Co(NH3)5Br2+ provided kinetic data for the reaction of ethyl radicals with FeCl2+ (k = (4.0 0.5) 106 M?1 s?1) and with FeBr2+ (k = (3.0 0.5) 107 M?1 s?1). Photochemical decarboxylation of propionic acid in the presence of Cu2+ generates ethylene and Cu+. Longer-chain acids also yield alpha olefins as exclusive products. These reactions become catalytic under constant purge with oxygen which plays a dual role. It reoxidizes Cu+ to Cu2+, and removes gaseous olefins to prevent accumulation of Cu+(olefin) complexes and depletion of Cu2+. The results underscore the profound effect that the choice of metal ions, the medium, and reaction conditions exert on the photochemistry of carboxylic acids.

Carraher, Jack; Pestovsky, Oleg; Bakac, Andreja

2012-03-14T23:59:59.000Z

227

Mercury Vapor Release from Broken Compact Fluorescent Lamps and In Situ Capture by New Nanomaterial Sorbents  

Science Journals Connector (OSTI)

There is one report of Hg poisoning (acrodynia) in a child exposed to broken tube-type fluorescents in a detailed case study presented by Tunnessen et al. (6). ... Similar release patterns but lower amounts were seen for spent bulbs (example result 90 ?g in 24 h) or from the fracture site of a new bulb after glass removal to simulate cleanup. ... Artificial lighting systems are transitioning from incandescent to compact fluorescent lamp (CFL) and light-emitting diode (LED) bulbs in response to the U.S. Energy Independence and Security Act and the EU Ecodesign Directive, which leads to energy ... ...

Natalie C. Johnson; Shawn Manchester; Love Sarin; Yuming Gao; Indrek Kulaots; Robert H. Hurt

2008-06-27T23:59:59.000Z

228

Influence of the lamp filling on the pumping conditions in a pulsed YAG:Nd3+ laser  

Science Journals Connector (OSTI)

The pumping conditions in pulsed YAG:Nd3+ lasers are determined, to a great extent, by the filling and the discharge conditions in the pump lamps. It is reported that the highest efficiency under free-oscillation conditions was obtained when krypton discharge lamps were used. These lamps had a discharge gap 60 mm long and 5 mm in diameter. They emitted flashes of about 200 ?sec duration. The best results were obtained when the initial gas pressure was ~1000 torr and the discharge energy was W ~ 100150J. The efficiency was lower when the value of W was either larger or smaller. The nature of the filling had little effect on the laser efficiency when xenon and krypton lamps were used to provide energies W close to the nominal value of 250J. The pumping conditions could not be improved significantly by the use of other fillings (inert gases or their mixtures were used). The principal results obtained were valid also when the lamps were operated at a repetition frequency of ? ? 10 Hz.

Vitalii M Podgaetskii; B V Skvortsov; A N Tokareva

1971-01-01T23:59:59.000Z

229

Method of controlling the mercury vapor pressure in a photo-chemical lamp or vapor filter used for Hg.sup.196 enrichment  

DOE Patents (OSTI)

The present invention is directed to a method of eliminating the cold spot zones presently used on Hg.sup.196 isotope separation lamps and filters by the use of a mercury amalgams, preferably mercury - indium amalgams. The use of an amalgam affords optimization of the mercury density in the lamp and filter of a mercury enrichment reactor, particularly multilamp enrichment reactors. Moreover, the use of an amalgam in such lamps and/or filters affords the ability to control the spectral line width of radiation emitted from lamps, a requirement for mercury enrichment.

Grossman, Mark W. (Belmont, MA)

1993-01-01T23:59:59.000Z

230

Method of controlling the mercury vapor pressure in a photo-chemical lamp or vapor filter used for Hg[sup 196] enrichment  

DOE Patents (OSTI)

The present invention is directed to a method of eliminating the cold spot zones presently used on Hg[sup 196] isotope separation lamps and filters by the use of a mercury amalgams, preferably mercury - indium amalgams. The use of an amalgam affords optimization of the mercury density in the lamp and filter of a mercury enrichment reactor, particularly multilamp enrichment reactors. Moreover, the use of an amalgam in such lamps and/or filters affords the ability to control the spectral line width of radiation emitted from lamps, a requirement for mercury enrichment.

Grossman, M.W.

1993-02-16T23:59:59.000Z

231

DOE Publishes Final Rule for the Request for Exclusion of 100 Watt R20 Short Incandescent Reflector Lamps from Energy Conservation Standards  

Energy.gov (U.S. Department of Energy (DOE))

The Department of Energy has published a final rule regarding the request for exclusion of 100 Watt R20 short incandescent reflector lamps from energy conservation standards.

232

A theoretical study of the incandescent filament lamp performance under voltage flicker  

SciTech Connect

Incandescent filament lamp flicker, produced by voltage fluctuation, is a power quality problem that caused engineering concern since the onset of electrical illumination technology. The flicker phenomenon was analyzed and explained in early studies. Standards dealing with acceptable flicker levels are well known, nevertheless, today the discussion about flicker continues to be a top priority topic due to the fact that steady-state and transient voltage waveform distortion is a growing problem in low and medium voltage systems. In many situations voltage flicker is caused by subharmonics and interharmonics of voltage. Cycloconverters, welders and arc furnaces, eccentrically operating tools and integral cycle controlled power equipment are notorious for producing voltage flicker. The goal of this paper is to provide solid mathematical basis for the analytical modeling of incandescent filament lamp flicker when the voltage is nonsinusoidal. A mathematical model that enables the evaluation of the luminous flux modulation caused by noninteger harmonics (subharmonics and interharmonics) is presented. Three situations are detailed: square-wave voltage modulation, sinusoidal modulation and the case of noninteger harmonics with nearly contiguous frequencies.

Peretto, L. [Univ. of Bologna (Italy)] [Univ. of Bologna (Italy); Emanuel, A.E. [Worcester Polytechnic Inst., MA (United States)] [Worcester Polytechnic Inst., MA (United States)

1997-01-01T23:59:59.000Z

233

High Permeability Ternary Palladium Alloy Membranes with Improved Sulfur and Halide Tolerance  

NLE Websites -- All DOE Office Websites (Extended Search)

9 9 HigH Permeability ternary Palladium alloy membranes witH imProved sulfur and Halide tolerance Description A critical step in the transition to the hydrogen economy is the separation of hydrogen from coal gasification gases (syngas) or methane. This is typically accomplished through membrane separation. Past research has shown that palladium (Pd) alloys possess great potential as robust and economical membranes. However, the search for the optimal binary or ternary alloys is an involved and costly process due to the immense number of alloy variations that could be prepared and tested. Recent modeling work at Georgia Institute of Technology using density functional theory (DFT) identified several promising ternary alloy compositions with improved

234

Northeastern Rural E M C | Open Energy Information  

Open Energy Info (EERE)

Northeastern Rural E M C Northeastern Rural E M C Jump to: navigation, search Name Northeastern Rural E M C Place Indiana Utility Id 20603 Utility Location Yes Ownership C NERC Location RFC NERC RFC Yes RTO PJM Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Outdoor Lighting Energy: Ballasted Lamps 1000W Lighting Outdoor Lighting Energy: Ballasted Lamps 100W Lighting Outdoor Lighting Energy: Ballasted Lamps 150W Lighting Outdoor Lighting Energy: Ballasted Lamps 175W Lighting Outdoor Lighting Energy: Ballasted Lamps 200W Lighting Outdoor Lighting Energy: Ballasted Lamps 250W Lighting

235

The Model 5000-16C 1000 WATT FEL Lamp Standard pro-vides absolute calibration of spectral irradiance from 250 nm to  

E-Print Network (OSTI)

The Model 5000-16C 1000 WATT FEL Lamp Standard pro- vides absolute calibration of spectral. It has been selected by the National Institute of Standards and Technology to replace the 1000 watt, DXW-pin 1000 watt lamp that is adapted by Gamma Scientific into a bi-post configuration. It is used

236

Development of protective polymer coatings for silver halide fibers and their application as threshold level sensors for chlorinated hydrocarbons in sea water  

Science Journals Connector (OSTI)

The stability of silver halide fibers in artificial sea water (ASW) with and without a protective ... sensor system for the quantitative detection of chlorinated hydrocarbons (CHC) also in sea water.

R. Gbel; R. Krska; R. Kellner; A. Katzir

237

Effect of helium addition on discharge characteristics in a flat fluorescent lamp  

SciTech Connect

The discharge characteristics of a multielectrode dual coplanar in a mercury-free flat fluorescent lamp were investigated using brightness-efficiency measurement and the infrared (IR) spectrum and intensified charge coupled device (ICCD) characteristics. The level of brightness was above 14 900 cd/m{sup 2} under the conditions of neon--50% xenon-8% He gas composition, 150 Torr pressure, and 20 kHz alternating current pulse. The ICCD results revealed a faster and wider discharge with a Ne-50% Xe-8% He gas composition. The effect of adding helium (He) to Ne-50% Xe revealed a faster peak emission, as confirmed by ICCD images. From the gated IR emission spectrum, the intensity ratio of I{sub 823nm}/I{sub 828nm} was {approx}8% higher with Ne-50% Xe-8% He than with Ne-50% Xe under the same pressure and applied voltage conditions.

Lee, Seong-Eui; Lee, Ho-Nyeon; Park, Hyoung-Bin; Lee, Kyo Sung; Choi, Kyung Cheol [Materials and Devices Research Center, Samsung Advanced Institute of Technology, Suwon 440-600 (Korea, Republic of); Department of Electronics Engineering, Sejong University, Seoul 143-747 (Korea, Republic of); Department of Electrical Engineering and Computer Science, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701 (Korea, Republic of)

2005-11-01T23:59:59.000Z

238

A Novel High-Power-Factor LED-Lamp Driver Based on a Single-Stage Power Conversion  

Science Journals Connector (OSTI)

This paper proposes a novel single-stage driver for supplying a T8-type light-emitting diode (LED) lamp with high power factor. The presented driver integrates a dual buck-boost converter with coupled inductors and a half-bridge series-resonant converter ... Keywords: converter, driver, light-emitting diode (LED)

Chun An Cheng, En Chih Chang, Ching Shien Tseng, Tsung Yuan Chung

2014-06-01T23:59:59.000Z

239

EA-1881: Energy Conservation Program: Energy Conservation Standards for  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

81: Energy Conservation Program: Energy Conservation Standards 81: Energy Conservation Program: Energy Conservation Standards for Fluorescent Lamp Ballasts EA-1881: Energy Conservation Program: Energy Conservation Standards for Fluorescent Lamp Ballasts Summary This EA evaluates the environmental impacts of a proposal to amend energy conservation standards for various consumer products and certain commercial and industrial equipment, including fluorescent lamp ballasts. Public Comment Opportunities No public comment opportunities available at this time. Documents Available for Download October 20, 2011 EA-1881: Finding of No Significant Impact Energy Conservation Program: Energy Conservation Standards for Fluorescent Lamp Ballasts (October 2011) October 5, 2011 EA-1881: Final Environmental Assessment Energy Conservation Program: Energy Conservation Standards for Fluorescent

240

Room Air Conditioners | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Test Results roomairconditioner v1.6.xlsx More Documents & Publications Commercial Air Conditioners and Heat Pumps Fluorescent Lamp Ballasts Residential Condensing Gas Furnaces...

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Data:Dc5cbc5d-73c0-4b83-9363-aabc0684d3fd | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

242

Data:E3f4ce5f-059c-48a2-8bf9-377f80f3ad2d | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

243

Data:44a519ea-0181-42a9-8ecd-0e4abc613c6a | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

244

Data:677fe40a-715e-431d-91b8-b244991f6895 | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

245

Data:25de9d78-d34a-4f8f-b2dc-e4614cc22f27 | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

246

Data:1ea0a40c-2af4-4d40-acbb-b25d3e7a5e5b | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

247

Data:95c46391-13dd-4d17-9534-7b547a7e4397 | Open Energy Information  

Open Energy Info (EERE)

Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to...

248

Data:39c45976-8d46-447d-808e-ec2688e4205a | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

249

Data:8e1a5854-0e58-4eb7-9876-4a875963c1e6 | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

250

Data:750230c9-ba6a-4f03-b6c0-6e33826c6b3d | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

251

Data:51274182-efac-4d2d-854f-ee4468e13286 | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

252

Data:2ef55dfb-8c4c-4fb8-ae1e-cf2a43a6e9c6 | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

253

Data:32627615-d9ec-4d10-a1ec-04610aa23fbc | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

254

Data:87d099e1-66f4-45d7-8ee1-a4ef61148ac7 | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

255

Data:2f76408d-5e25-40c1-b703-d0f2e9d2a46b | Open Energy Information  

Open Energy Info (EERE)

Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to...

256

Data:4b137db8-acda-4135-8c79-3e9921f1c0ca | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

257

Data:E5e90995-092a-474b-afba-911375543a45 | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

258

Data:25b8a7f6-0ab9-4bb2-a041-07566889baa0 | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

259

Data:A55b88b8-16f4-4a41-8e5e-e4e6ee726743 | Open Energy Information  

Open Energy Info (EERE)

Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to...

260

Data:5d264c16-9059-4579-bdee-430c53ec5c07 | Open Energy Information  

Open Energy Info (EERE)

and Regulations. APPLICABILITY: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaires and poles conforming to...

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Illuminated Exit Signs | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

federal energy conservation standards. illuminatedexitsignsv1.1.xlsx More Documents & Publications Beverage Vending Machines Residential Clothes Dryers Fluorescent Lamp Ballasts...

262

External Power Supplies | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

federal energy conservation standards. externalpowersuppliesv1.1.xlsx More Documents & Publications Illuminated Exit Signs Fluorescent Lamp Ballasts Beverage Vending Machines...

263

DOE February 2012 ECS Report to Congress  

Office of Environmental Management (EM)

and refrigerator-freezers, fluorescent lamp ballasts, and direct heating equipment, and test procedures for walk-in coolers and walk-in freezers, automatic commercial ice makers,...

264

CX-002017: Categorical Exclusion Determination | Department of...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Retrofit activities include installing ballasts, light sockets, lamps, and motion sensors. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-002017.pdf More Documents & Publications...

265

Making the Market Right for Environmentally Sound Energy-Efficient Technologies: U.S. Buildings Sector Successes that Might Work in Developing Countries and Eastern Europe  

E-Print Network (OSTI)

than their 100-year old incandescent ancestors. However,Hz core-coil ballasts. Incandescent lighting consumes aboutthe developing world, incandescent lamps drive peak demand,

Gadgil, A.J.

2008-01-01T23:59:59.000Z

266

Analysis of Potential Energy Saving and CO2 Emission Reduction of Home Appliances and Commercial Equipments in China  

E-Print Network (OSTI)

irons Automatic rice cookers Microwave Radio receivers andFluorescent Lamp Ballast Rice cooker Microwave ovens OfficeOthers include: rice cookers, microwaves, laser printers,

Zhou, Nan

2010-01-01T23:59:59.000Z

267

Calcium looping process for high purity hydrogen production integrated with capture of carbon dioxide, sulfur and halides  

DOE Patents (OSTI)

A process for producing hydrogen comprising the steps of: (i) gasifying a fuel into a raw synthesis gas comprising CO, hydrogen, steam, sulfur and halide contaminants in the form of H.sub.2S, COS, and HX, wherein X is a halide; (ii) passing the raw synthesis gas through a water gas shift reactor (WGSR) into which CaO and steam are injected, the CaO reacting with the shifted gas to remove CO.sub.2, sulfur and halides in a solid-phase calcium-containing product comprising CaCO.sub.3, CaS and CaX.sub.2; (iii) separating the solid-phase calcium-containing product from an enriched gaseous hydrogen product; and (iv) regenerating the CaO by calcining the solid-phase calcium-containing product at a condition selected from the group consisting of: in the presence of steam, in the presence of CO.sub.2, in the presence of synthesis gas, in the presence of H.sub.2 and O.sub.2, under partial vacuum, and combinations thereof.

Ramkumar, Shwetha; Fan, Liang-Shih

2013-07-30T23:59:59.000Z

268

DOE CALiPER Program, Report 21.2: Linear (T8) LED Lamp Performance in Five Types of Recessed Troffers  

SciTech Connect

Although lensed troffers are numerous, there are many other types of optical systems as well. This report looked at the performance of three linear (T8) LED lamps chosen primarily based on their luminous intensity distributions (narrow, medium, and wide beam angles) as well as a benchmark fluorescent lamp in five different troffer types. Also included are the results of a subjective evaluation. Results show that linear (T8) LED lamps can improve luminaire efficiency in K12-lensed and parabolic-louvered troffers, effect little change in volumetric and high-performance diffuse-lensed type luminaires, but reduce efficiency in recessed indirect troffers. These changes can be accompanied by visual appearance and visual comfort consequences, especially when LED lamps with clear lenses and narrow distributions are installed. Linear (T8) LED lamps with diffuse apertures exhibited wider beam angles, performed more similarly to fluorescent lamps, and received better ratings from observers. Guidance is provided on which luminaires are the best candidates for retrofitting with linear (T8) LED lamps.

Miller, Naomi J.; Perrin, Tess E.; Royer, Michael P.; Wilkerson, Andrea M.; Beeson, Tracy A.

2014-05-20T23:59:59.000Z

269

Resistivity measurements of halide-salt/MgO separators for thermal cells  

SciTech Connect

Resistivities of 20 compositions of halide-salt/MgO mixtures (various selections and percentages of LiF, LiCl, LiBr, KCl, KBr, CsBr, and MgO) to be used in Li-alloy/metal sulfide cells have been measured at temperatures between the melting point of a particular mixture and 500{degrees}C. The resistivities were determined with cold-pressed electrolyte-binder pellets by using a special cell and DC measuring technique. Temperature, salt composition, and MgO content were found to have a strong influence on resistivity. These factors are listed in decreasing order of the magnitude of the effect. The fabrication density (porosity) of the pellet also has some effect on resistivity. These measured resistivities provide a data base to select optimum compositions of electrolyte-binder pellets for LiSi/FeS{sub 2} thermal batteries and to calculate area-specific resistances of these components for battery modeling and optimization. 5 refs., 7 figs.

Redey, L.; McParland, M. (Argonne National Lab., IL (USA)); Guidotti, R. (Sandia National Labs., Albuquerque, NM (USA))

1990-01-01T23:59:59.000Z

270

Color stable phosphors for LED lamps and methods for preparing them  

SciTech Connect

An LED lamp includes a light source configured to emit radiation with a peak intensity at a wavelength between about 250 nm and about 550 nm; and a phosphor composition configured to be radiationally coupled to the light source. The phosphor composition includes particles of a phosphor of formula I, said particles having a coating composition disposed on surfaces thereof; ((Sr.sub.1-zM.sub.z).sub.1-(x+w)A.sub.wCe.sub.x).sub.3(Al.sub.1-ySi.sub.y-)O.sub.4+y+3(x-w)F.sub.1-y-3(x-w) I wherein the coating composition comprises a material selected from aluminum oxide, magnesium oxide, calcium oxide, barium oxide, strontium oxide, zinc oxide, aluminum hydroxide, magnesium hydroxide, calcium hydroxide, barium hydroxide, strontium hydroxide, zinc hydroxide, aluminum phosphate, magnesium phosphate, calcium phosphate, barium phosphate, strontium phosphate, and combinations thereof; and A is Li, NA, K, or Rb, or a combination thereof; M is Ca, Ba, Mg, Zn, or a combination thereof; and 0

Murphy, James Edward; Setlur, Anant Achyut; Camardello, Samuel Joseph

2013-11-26T23:59:59.000Z

271

Iterative Boltzmann plot method for temperature and pressure determination in a xenon high pressure discharge lamp  

SciTech Connect

The Boltzmann plot method allows to calculate plasma temperatures and pressures if absolutely calibrated emission coefficients of spectral lines are available. However, xenon arcs are not very well suited to be analyzed this way, as there are only a limited number of lines with atomic data available. These lines have high excitation energies in a small interval between 9.8 and 11.5 eV. Uncertainties in the experimental method and in the atomic data further limit the accuracy of the evaluation procedure. This may result in implausible values of temperature and pressure with inadmissible uncertainty. To omit these shortcomings, an iterative scheme is proposed that is making use of additional information about the xenon fill pressure. This method is proved to be robust against noisy data and significantly reduces the uncertainties. Intentionally distorted synthetic data are used to illustrate the performance of the method, and measurements performed on a laboratory xenon high pressure discharge lamp are analyzed resulting in reasonable temperatures and pressures with significantly reduced uncertainties.

Zalach, J.; Franke, St. [INP Greifswald, Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany)

2013-01-28T23:59:59.000Z

272

Analysis of Na and Ba in an atomic fluorescence method with excitation by a pulsed dye laser with lamp pumping  

SciTech Connect

Among the laser methods used in atomic spectroscopy, atomic fluorescence resonance spectroscopy together with an atomic ionization technique make it possible to work with individual atoms. This paper reports on the determination of Na and Ba in aqueous solutions of their salts with atomic fluorescence analysis performed wih a dye laser and lamp pumping, the pulse of generation having a length of 1-2 usec. The detection limit of elements in atomic fluorescence analysis performed wih dye lasers with lamp pumping can be reduced by increasing the spectral density of the laser radiation through narrowing the line of generation, by employing other dyes to excite lines of greater intensity, by improving the recording system of the fluorescence spectra, and by improving the atomization of the samples to be analyzed.

Kukvshim, V.G.

1986-04-01T23:59:59.000Z

273

Design and Realize of the Graphics Platform for LED Lamps Layout Based on GDI+ and Dual-Buffer  

Science Journals Connector (OSTI)

Based on the GDI+ class library and dual-buffer technology of .NET framework, the software for LED lamps layout is developed. On the basis of determining the scheme of layout platform, the metafile class library model by Composite design-set and the process of calling the LED pixels metafile symbol interface are designed firstly. The design method of realizing the LED pixels metafile visual editing on the drawn LED logical pixel based on GDI+ is analyzed. The dual-buffer technology is used to solve the problem of flicker when fast refreshing. The testing results show that the platform can meet the basic function requirements of engineering application, and realize partial adjust on the process of LED lamps layout without distortion.

Wen Yuanmei; Nie Xinming; Liu Guixiong

2012-01-01T23:59:59.000Z

274

STATE OF CALIFORNIA CERTIFICATE OF COMPLIANCE AND FIELD INSPECTION CHECKLIST  

E-Print Network (OSTI)

Watts: 1. Type of luminaire (i.e.: post top, wall pack, surface, shoe box); for non-incandescent luminaires, indicate nominal lamp wattage and lamp type ( i.e.: fluorescent, incandescent, HID); ballast type. For incandescent luminaires, the lum

275

Mechanical design of PlayLamp : a minimally intrusive device for recording the behavior of children at-risk of developmental disorders  

E-Print Network (OSTI)

This thesis paper documents the design process, decisions, and outcomes of the design of the physical form factor of PlayLamp, a device for video and audio recording the development of children at-risk of having developmental ...

Steger, Stephen Andrew

2008-01-01T23:59:59.000Z

276

CALiPER Report 20.1: Subjective Evaluation of Beam Quality, Shadow Quality, and Color Quality for LED PAR38 Lamps  

Energy.gov (U.S. Department of Energy (DOE))

This December 3, 2013 webinar explored the findings ofCALiPER 20.1: Subjective Evaluation of Beam Quality, Shadow Quality, and Color Quality for LED PAR38 Lamps and discussed what attributes to...

277

Local Resistance Profiling of Ultra Shallow Junction Annealed with Combination of Spike Lamp and Laser Annealing Processes using Scanning Spreading Resistance Microscope  

SciTech Connect

Local resistance profiles of ultra shallow boron and arsenic implanted into silicon with energies of 2.0 and 4.0 keV and doses of 2.0x10{sup 15} and 1.0x10{sup 15} ions/cm{sup 2} activated by a combination of conventional spike lamp and laser annealing processes were measured by scanning spreading resistance microscope (SSRM) with a depth resolution of less than 10 nm. The lowest local resistance at the low resistance region in 2.0 keV boron implanted silicon with 1050 deg. C spike lamp annealing followed by 0.35 kW/mm{sup 2} laser annealing was half of that without laser annealing. The lowest local resistance at the low resistance region in the arsenic implanted silicon activated by 1050 deg. C spike lamp annealing followed by 0.39 kW/mm{sup 2} laser annealing was 74% lower than that followed by 0.36 kW/mm{sup 2} laser annealing. The lowest local resistances at the low resistance regions in the arsenic implanted silicon with 0.36 and 0.39 kW/mm{sup 2} laser annealing followed by 1050 deg. C spike lamp annealing were 41 and 33% lower than those with spike lamp annealing followed by laser annealing. Laser annealing followed by spike lamp annealing could suppress the diffusion of the impurities and was suitable for making the ultra shallow and low resistance regions.

Abo, Satoshi; Nishikawa, Kazuhisa; Ushigome, Naoya; Wakaya, Fujio; Takai, Mikio [Center for Quantum Science and Technology under Extreme Conditions, Osaka University, 1-3, Machikaneyama, Toyonaka, Osaka, 560-8531 (Japan); Iwamatsu, Toshiaki; Oda, Hidekazu [Advanced Device Technology Department, Production and Technology Unit, Devices and Analysis Technology Division, Renesas Electronics Corporation, 751, Horiguchi, Hitachinaka, Ibaraki, 312-8504 (Japan)

2011-01-07T23:59:59.000Z

278

Observed Minimum Illuminance Threshold for Night Market Vendors in Kenya who use LED Lamps  

SciTech Connect

Creation of light for work, socializing, and general illumination is a fundamental application of technology around the world. For those who lack access to electricity, an emerging and diverse range of LED based lighting products hold promise for replacing and/or augmenting their current fuel-based lighting sources that are costly and dirty. Along with analysis of environmental factors, economic models for total cost-ofownership of LED lighting products are an important tool for studying the impacts of these products as they emerge in markets of developing countries. One important metric in those models is the minimum illuminance demanded by end-users for a given task before recharging the lamp or replacing batteries. It impacts the lighting service cost per unit time if charging is done with purchased electricity, batteries, or charging services. The concept is illustrated in figure 1: LED lighting products are generally brightest immediately after the battery is charged or replaced and the illuminance degrades as the battery is discharged. When a minimum threshold level of illuminance is reached, the operational time for the battery charge cycle is over. The cost to recharge depends on the method utilized; these include charging at a shop at a fixed price per charge, charging on personal grid connections, using solar chargers, and purchasing dry cell batteries. This Research Note reports on the observed"charge-triggering" illuminance level threshold for night market vendors who use LED lighting products to provide general and task oriented illumination. All the study participants charged with AC power, either at a fixed-price charge shop or with electricity at their home.

Johnstone, Peter; Jacobson, Arne; Mills, Evan; Radecsky, Kristen

2009-03-21T23:59:59.000Z

279

The pressure induced B1-B2 phase transition of alkaline halides and alkaline earth chalcogenides. A first principles investigation  

SciTech Connect

In this work, we considered the pressure induced B1-B2 phase transition of AB compounds. The DFT calculations were carried out for 11 alkaline halides, 11 alkaline earth chalcogenides and the lanthanide pnictide CeP. For both the B1 and the B2 structures of each compound, the energy was calculated as a function of the cell volume. The transition pressure, the bulk moduli and their pressure derivatives were obtained from the corresponding equations of state. The transition path of the Buerger mechanism was described using roots of the transition matrix. We correlated the computed enthalpies of activation to some structure defining properties of the compounds. A fair correlation to Pearsons hardness of the ions was observed. -- Graphical abstract: Pressure induced transition from the B1 structure (left) via the transition state (middle) to the B2 structure (right). Display Omitted highlights: > Pressure induced phase transitions in AB compounds were considered. > Alkaline halides and alkaline earth chalcogenides were treated. > DFT calculations with periodic boundary conditions were applied. > The transition path was described by roots of the transition matrix. > The enthalpy of activation was calculated for numerous compounds.

Potzel, Oliver, E-mail: oliver.potzel@uni-ulm.d [Institute of Theoretical Chemistry, D-89069 Ulm (Germany); Taubmann, Gerhard, E-mail: gerhard.taubmann@uni-ulm.d [Institute of Theoretical Chemistry, D-89069 Ulm (Germany)

2011-05-15T23:59:59.000Z

280

Glass and glass-derivative seals for use in energy-efficient fuel cells and lamps  

SciTech Connect

For solid oxide fuel cells (SOFC), a series of 18 sealing glasses have been prepared and characterized. From the whole design space, several glasses were ''downselected'' and studied in detail to describe their behaviors in simulated fuel cell environments. One of the glasses was found to outperform all others, including the well-known G18 sealant developed at Pacific Northwest National Laboratory. The new glass composition showed lower bulk electrical conductivity, excellent sealing and wetting behavior when sealing under applied load, and qualitatively superior performance when exposed to wet hydrogen for 800 hours. Traditional melting was used to prepare all of the glasses that were studied in detail. The sol-gel approach was used to synthesize several compositions, but it was found that the glasses crystallized very rapidly during heating, precluding sealing. The glass characterization included measurements of the viscosity and thermal expansion of the glasses, as well as the thermal expansion of the partly crystalline glass ceramics. In addition, the wetting and sintering behavior of all glasses has been measured, as well as the crystallization behavior. The time and temperature at which crystalline phases form from the glasses has been determined for all of the glasses. Each glass ceramic contains at least two crystalline phases, and most of the crystalline phases have been positively identified. The body of fundamental data provides a platform for future developments for high temperature sealants, and the newly-developed glass compositions appear promising for large-scale testing. The second component of the work, focused on seals for higher-temperature discharge lighting, has focused on determining the phase relations in the yttria-alumina-silica system at various silica levels. Functional testing of one of the candidate sealants demonstrated that it performs well in current HID lighting applications. Further testing is required to evaluate its performance in next-generation lamps that operate at higher temperatures, but the baseline phase equilibria and crystallization behavior has been established for additional development. Again, traditional melting and sol-gel synthesis have been employed, and the sol-gel method was successful for preparing new phases that were discovered during the work. Four new phases have been identified and synthesized in pure form, from which full structure solutions were obtained as well as the anisotropic thermal expansion for each phase.

Scott Misture; Arun Varshineya; Matthew Hall; Sylvia DeCarr; Steve Bancheri

2005-07-28T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Potential Environmental Impacts from the Metals in Incandescent, Compact Fluorescent Lamp (CFL), and Light-Emitting Diode (LED) Bulbs  

Science Journals Connector (OSTI)

Artificial lighting systems are transitioning from incandescent to compact fluorescent lamp (CFL) and light-emitting diode (LED) bulbs in response to the U.S. Energy Independence and Security Act and the EU Ecodesign Directive, which leads to energy savings and reduced greenhouse gas emissions. ... The CFLs and LEDs have higher resource depletion and toxicity potentials than the incandescent bulb due primarily to their high aluminum, copper, gold, lead, silver, and zinc. ... mercury pollution; redn. in electricity demand from the substitution of incandescent bulbs with fluorescents leads to reduced mercury emissions during the use of the bulb. ...

Seong-Rin Lim; Daniel Kang; Oladele A. Ogunseitan; Julie M. Schoenung

2012-12-13T23:59:59.000Z

282

2014-05-05 Issuance: Test Procedures for High-Intensity Discharge Lamps; Supplemental Notice of Proposed Rulemaking  

Energy.gov (U.S. Department of Energy (DOE))

This document is a pre-publication Federal Register supplemental notice of proposed rulemaking regarding test procedures for high-intesity discharge lamps, as issued by the Deputy Assistant Secretary for Energy Efficiency on May 5, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

283

2015-01-26 Issuance: Energy Conservation Standards for General Service Lamps; Extension of Public Comment Period  

Energy.gov (U.S. Department of Energy (DOE))

This document is a pre-publication Federal Register extension of comment period regarding energy conservation standards for general service lamps, as issued by the Deputy Assistant Secretary for Energy Efficiency on January 26, 2015. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

284

Halide, Chromate, and Phosphate Impacts on LAW Glass for Dynamic Flowsheet 24590-WTP-MCR-PET-09-0037, Rev. 1  

SciTech Connect

Revision 1 of this Model Change Request changed Equation 6 in Attachment Al only. Melter studies have shown that halide, chromium, and phosphates can cause precipitation of solids that can interfer the melting process. Pilot melter data now shows what concentrations LAW glass can tolerate. These limits shall be incorporated into the existing LAW glass algorithm per Attachment Al.

Gimpel, Rodney F.; Kruger, Albert A.

2013-12-16T23:59:59.000Z

285

Universal Waste Management Procedure: 8.42 Created: 7/30/2014 Version: 1.2 Revised: 7/30/2014  

E-Print Network (OSTI)

fluorescent lamps are classified as Universal Wastes due to their mercury content. Other examples of lamps pressure sodium, and metal halide lamps. It can be expected that fluorescent and HID lamps, including green batteries are managed as universal waste. 2. Lamps are defined by the above regulations as "the bulb or tube

Jia, Songtao

286

518 IEEE TRANSACTIONS ON PLASMA SCIENCE, VOL. 33, NO. 2, APRIL 2005 Plasma Dynamics During Breakdown in  

E-Print Network (OSTI)

, lamp, modeling, plasma. METAL halide arc lamps are widely used sources of in- door and large area plasma hydrodynamics model was used to investigate breakdown in metal halide lamp. Images depicting518 IEEE TRANSACTIONS ON PLASMA SCIENCE, VOL. 33, NO. 2, APRIL 2005 Plasma Dynamics During

Kushner, Mark

287

Data:239dd8c3-2660-4fb5-a10f-200895eb226c | Open Energy Information  

Open Energy Info (EERE)

c3-2660-4fb5-a10f-200895eb226c c3-2660-4fb5-a10f-200895eb226c No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 250W HPS - Shoebox ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

288

Data:982a1454-aa93-4ab1-a5cd-76205b2d6aa6 | Open Energy Information  

Open Energy Info (EERE)

aa93-4ab1-a5cd-76205b2d6aa6 aa93-4ab1-a5cd-76205b2d6aa6 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 100W HPS - Traditional ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

289

Data:982fa5fd-b44a-4196-8c97-39a136f8ea38 | Open Energy Information  

Open Energy Info (EERE)

b44a-4196-8c97-39a136f8ea38 b44a-4196-8c97-39a136f8ea38 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 150W HPS - Expressway ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

290

Engineered Products: Proposed Penalty (2012-SE-5401) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Proposed Penalty (2012-SE-5401) Proposed Penalty (2012-SE-5401) Engineered Products: Proposed Penalty (2012-SE-5401) July 19, 2012 DOE alleged in a Notice of Proposed Civil Penalty that Engineered Products Company manufactured/privately-labeled and distributed a number of units of noncompliant basic model 15701, a metal halide lamp fixture with a magnetic probe-start ballast in the U.S. Federal law subjects manufacturers and private labelers to civil penalties if those parties distribute in the U.S. products that do not meet applicable energy conservation standards. This civil penalty notice advises the company of the potential penalties and DOE's administrative process, including the company's right to a hearing. Engineered Products: Proposed Penalty (2012-SE-5401) More Documents & Publications

291

Independence Power and Light - Commercial Energy Efficiency Rebate Program  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Independence Power and Light - Commercial Energy Efficiency Rebate Independence Power and Light - Commercial Energy Efficiency Rebate Program Independence Power and Light - Commercial Energy Efficiency Rebate Program < Back Eligibility Commercial Savings Category Heating & Cooling Commercial Heating & Cooling Cooling Home Weatherization Construction Commercial Weatherization Design & Remodeling Appliances & Electronics Commercial Lighting Lighting Maximum Rebate $20,000, or 30% of the total project cost annually per organization Program Info State Missouri Program Type Utility Rebate Program Rebate Amount High Performance T-8 Systems: $20-$30 Reduced-Wattage T-8 Systems: $20-$30 Standard T-8 Lamp: $2 Standard T-8 Electric Ballast: $10 400W HID Replacement (250W or less T8, T5, or T5HO Fluorescent): $75 Pulse Start Metal Halide Fixture: $50

292

Data:Fd4a1d85-7f5c-46aa-90b2-bccb09df9df3 | Open Energy Information  

Open Energy Info (EERE)

-7f5c-46aa-90b2-bccb09df9df3 -7f5c-46aa-90b2-bccb09df9df3 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service-Parking Lot Shoebox- One Fixture (350/400 W MH/HPS) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh):

293

Data:Ec8a2a34-0d66-487d-a4d3-3d24e442eb86 | Open Energy Information  

Open Energy Info (EERE)

4-0d66-487d-a4d3-3d24e442eb86 4-0d66-487d-a4d3-3d24e442eb86 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 250W HPS - Expressway ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability

294

Data:D96a197b-661d-43e7-83c0-879ab36d94c2 | Open Energy Information  

Open Energy Info (EERE)

97b-661d-43e7-83c0-879ab36d94c2 97b-661d-43e7-83c0-879ab36d94c2 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 100W HPS - Cobrahead ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability

295

Data:Da8c4406-ba6e-4564-aa77-7003d74bee60 | Open Energy Information  

Open Energy Info (EERE)

06-ba6e-4564-aa77-7003d74bee60 06-ba6e-4564-aa77-7003d74bee60 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 1000W MH - Shoebox ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

296

All General Counsel Reports | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

November 21, 2012 November 21, 2012 Teddico: Proposed Penalty (2012-SE-5409) DOE alleged in a Notice of Proposed Civil Penalty that The Electrical Design, Development and Implementation Company d/b/a Teddico manufactured and distributed noncompliant metal halide lamp fixtures with magnetic probe-start ballasts in the U.S. November 20, 2012 Midea: Penalty Notice Withdrawal (2010-SE-0110) DOE withdrew its January 26, 2012 Notice of Proposed Civil Penalty, but retained the right to take further enforcement actions. November 20, 2012 Midea: Proposed Penalty (2010-SE-0110, 2012-SE-1402, 2012-SE-1404) DOE alleged in a Notice of Proposed Civil Penalty that Midea America Corp., Hefei Hualing Co., Ltd., and China Refrigeration Industry Co., Ltd. manufactured and distributed noncompliant refrigerator-freezers and

297

Data:B86ebcf3-870c-4233-9e75-a0471a221774 | Open Energy Information  

Open Energy Info (EERE)

-870c-4233-9e75-a0471a221774 -870c-4233-9e75-a0471a221774 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 400W MH - Shoebox ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

298

Data:245bd7d1-d33d-4993-aba9-822ff9f1fdfc | Open Energy Information  

Open Energy Info (EERE)

-d33d-4993-aba9-822ff9f1fdfc -d33d-4993-aba9-822ff9f1fdfc No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 250W HPS - Cobrahead ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

299

All General Counsel Reports | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

20, 2012 20, 2012 ASKO Appliances: Order (2012-CE-19/2004) DOE ordered ASKO Appliances, Inc. to pay a $36,500 civil penalty after finding ASKO had failed to certify that certain models of residential dishwashers and clothes washers comply with the applicable energy and water conservation standards. July 19, 2012 Engineered Products: Proposed Penalty (2012-SE-5401) DOE alleged in a Notice of Proposed Civil Penalty that Engineered Products Company manufactured/privately-labeled and distributed a number of units of noncompliant basic model 15701, a metal halide lamp fixture with a magnetic probe-start ballast in the U.S. July 18, 2012 Ex Parte Communication, July 18, 2012 Meeting On Wednesday July 18, 2012, three energy efficiency advocates met with representatives of the Department of Energy to discuss the Notice of

300

Teddico: Proposed Penalty (2012-SE-5409) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Proposed Penalty (2012-SE-5409) Proposed Penalty (2012-SE-5409) Teddico: Proposed Penalty (2012-SE-5409) November 21, 2012 DOE alleged in a Notice of Proposed Civil Penalty that The Electrical Design, Development and Implementation Company d/b/a Teddico manufactured and distributed noncompliant metal halide lamp fixtures with magnetic probe-start ballasts in the U.S. Federal law subjects manufacturers and private labelers to civil penalties if those parties distribute in the U.S. products that do not meet applicable energy conservation standards. This civil penalty notice advises the company of the potential penalties and DOE's administrative process, including the company's right to a hearing. Teddico: Proposed Penalty (2012-SE-5409) More Documents & Publications Teddico: Noncompliance Determination (2012-SE-5409)

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Data:3da53f69-28ca-4c89-b263-5aecb1ab1178 | Open Energy Information  

Open Energy Info (EERE)

9-28ca-4c89-b263-5aecb1ab1178 9-28ca-4c89-b263-5aecb1ab1178 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service- Roadway Luminaires- (400 W HPS with Pole) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

302

Data:042eb420-7802-4b5a-9228-e829cba1421a | Open Energy Information  

Open Energy Info (EERE)

7802-4b5a-9228-e829cba1421a 7802-4b5a-9228-e829cba1421a No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 400W HPS - Cobrahead ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

303

Data:7d6e144f-1ee4-4317-9d4d-5000bbb042b0 | Open Energy Information  

Open Energy Info (EERE)

4f-1ee4-4317-9d4d-5000bbb042b0 4f-1ee4-4317-9d4d-5000bbb042b0 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service-Parking Lot Shoebox- Two Fixture (350/400 W MH/HPS) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh):

304

Kansas City Power and Light - Commercial/Industrial Energy Efficiency  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4,907-$35,142 by business 4,907-$35,142 by business class size and differs among Missouri and Kansas residents. Program Info State Kansas Program Type Utility Rebate Program Rebate Amount Energy Audit ( Energy Audit (> 25,000 sq ft): 50% of cost, up to $500 High Performance T8 Fixtures: $20 - $30/fixture Standard T8 Lamps/Ballasts: $2 - $10/unit Lighting Power Density: $1/watt per square foot High Intensity Fluorescent: $50/fixture Pulse Star Metal Halide: $50/fixture Lighting Controls: $20 - $50 per sensor Single Phase Package/Split System AC: $92/ton Three Phase Unitary/Split System AC: $92/ton Unitary/Split System AC: $73 - $79/ton Motors: $50 - $130/motor Custom (Retrofit): The lesser of a buydown to a two year payback, or 50% of the incremental cost Custom (New Construction): The lesser of a buydown to a two year payback,

305

Kansas City Power and Light - Commercial/Industrial Energy Efficiency  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7,299-$52,276 by business 7,299-$52,276 by business class, size, new construction, retrofit, and location. Program Info State Missouri Program Type Utility Rebate Program Rebate Amount Energy Audit ( Energy Audit (> 25,000 sq ft): 50% of cost, up to $500 High Performance T8 Fixtures: $20 - $30/fixture Standard T8 Lamps/Ballasts: $2 - $10/unit Lighting Power Density: $1/watt per square foot High Intensity Fluorescent: $50/fixture Pulse Star Metal Halide: $50/fixture Lighting Controls: $20 - $50 per sensor Single Phase Package/Split System AC: $92/ton Three Phase Unitary/Split System AC: $92/ton Unitary/Split System AC: $73 - $79/ton Motors: $50 - $130/motor Custom (Retrofit): The lesser of a buydown to a two year payback, or 50% of the incremental cost Custom (New Construction): The lesser of a buydown to a two year payback,

306

Data:Ce257723-a06c-4647-a520-102fafcf2c22 | Open Energy Information  

Open Energy Info (EERE)

Ce257723-a06c-4647-a520-102fafcf2c22 Ce257723-a06c-4647-a520-102fafcf2c22 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service-Post Top Fixtures- (Traditional MH 150/175W) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh):

307

Data:957488aa-519a-412c-aab9-de57c307d0ba | Open Energy Information  

Open Energy Info (EERE)

aa-519a-412c-aab9-de57c307d0ba aa-519a-412c-aab9-de57c307d0ba No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service-Post Top Fixtures- (Galleria HPS 150W) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

308

Data:1ed95e55-77c3-4ba5-a97f-2ae396b39928 | Open Energy Information  

Open Energy Info (EERE)

5-77c3-4ba5-a97f-2ae396b39928 5-77c3-4ba5-a97f-2ae396b39928 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service-Post Top Fixtures- (Torch MH 250W) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

309

Data:Abebf4df-42b4-4191-a89f-831699aa0854 | Open Energy Information  

Open Energy Info (EERE)

Abebf4df-42b4-4191-a89f-831699aa0854 Abebf4df-42b4-4191-a89f-831699aa0854 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 150W HPS - Cobrahead ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability

310

Data:92d0a7d1-bb82-45db-994c-0dcc09e7cab4 | Open Energy Information  

Open Energy Info (EERE)

bb82-45db-994c-0dcc09e7cab4 bb82-45db-994c-0dcc09e7cab4 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 250W HPS - Traditional ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

311

Data:13c51b15-5cae-49e3-9ee6-400f38d52613 | Open Energy Information  

Open Energy Info (EERE)

-5cae-49e3-9ee6-400f38d52613 -5cae-49e3-9ee6-400f38d52613 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 175W MH - Torch ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

312

Data:Ef85a643-5658-4b95-8c6c-0599623b2f40 | Open Energy Information  

Open Energy Info (EERE)

3-5658-4b95-8c6c-0599623b2f40 3-5658-4b95-8c6c-0599623b2f40 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service- Flood Lights- (1000 W HPS/MV with Pole) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

313

Data:Dc676092-86ef-4bb7-80e3-b82a5cccd0d8 | Open Energy Information  

Open Energy Info (EERE)

2-86ef-4bb7-80e3-b82a5cccd0d8 2-86ef-4bb7-80e3-b82a5cccd0d8 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 400W HPS - Expressway ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability

314

Data:2ffcfa4e-d40e-4966-ad5f-08e2c6d81558 | Open Energy Information  

Open Energy Info (EERE)

ffcfa4e-d40e-4966-ad5f-08e2c6d81558 ffcfa4e-d40e-4966-ad5f-08e2c6d81558 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 400W HPS - Shoebox ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability

315

Data:68e73637-cd28-4a9c-9a21-63a07f0c4666 | Open Energy Information  

Open Energy Info (EERE)

7-cd28-4a9c-9a21-63a07f0c4666 7-cd28-4a9c-9a21-63a07f0c4666 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 150W HPS - Traditional ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability

316

Data:71d6b6fd-5996-4692-8470-e8e9fd2cea39 | Open Energy Information  

Open Energy Info (EERE)

fd-5996-4692-8470-e8e9fd2cea39 fd-5996-4692-8470-e8e9fd2cea39 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Jefferson Electric Member Corp Effective date: 2010/11/01 End date if known: Rate name: STREET LIGHTING SERVICE ( 250W MH - Shoebox ) Sector: Lighting Description: Additional fees for poles and transformers may apply Source or reference: ISU Documentation Source Parent: Comments Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either high pressure sodium (HPS) or metal halide (MH), and poles conforming to Cooperative specifications. Applicability Demand (kW)

317

Data:9d5d4f98-a7b3-4efb-9444-f86e08d70279 | Open Energy Information  

Open Energy Info (EERE)

8-a7b3-4efb-9444-f86e08d70279 8-a7b3-4efb-9444-f86e08d70279 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service- Roadway Luminaires- (400 W MV without Pole) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

318

Synthesis of rare gas-halide mixtures resulting in efficient XeF(C. -->. A) laser oscillation  

SciTech Connect

Significantly improved XeF(C..-->..A) laser performance has been achieved using electron beam excitation of complex, multicomponent gas mixtures specifically tailored so as to reduce medium transient absorption in the blue-green region. Use of Ar and Kr together as the effective rare gas buffer-energy transfer species, along with a combination of NF/sub 3/ and F/sub 2/ to produce the desired F-donor molecule characteristics, has permitted synthesis of near optimum medium properties for which XeF(C) is produced efficiently while transient absorption is minimized. With this technique we have achieved laser pulse energy density and intrinsic efficiency of 2.2 +- 0.3 J/l and approx.1.5%, respectively, values that are comparable to those of the B..-->..X rare gas-halide lasers.

Nighan, W.L.; Tittel, F.K.; Wilson W.L. Jr.; Nishida, N.; Zhu, Y.; Sauerbrey, R.

1984-11-01T23:59:59.000Z

319

Universal scaling of potential energy functions describing intermolecular interactions. II. The halide-water and alkali metal-water interactions  

SciTech Connect

The scaled forms of the newly introduced generalized potential energy functions (PEFs) describing intermolecular interactions [J. Chem. Phys. xx, yyyyy (2011)] have been used to fit the ab-initio minimum energy paths (MEPs) for the halide- and alkali metal-water systems X-(H2O), X=F, Cl, Br, I, and M+(H2O), M=Li, Na, K, Rb, Cs. These generalized forms produce fits to the ab-initio data that are between one and two orders of magnitude better in the ?2 than the original forms of the PEFs. They were found to describe both the long-range, minimum and repulsive wall of the potential energy surface quite well. Overall the 4-parameter extended Morse (eM) and generalized Buckingham exponential-6 (gB-e6) potentials were found to best fit the ab-initio data. Furthermore, a single set of parameters of the reduced form was found to describe all candidates within each class of interactions. The fact that in reduced coordinates a whole class of interactions can be represented by a single PEF, yields the simple relationship between the molecular parameters associated with energy (well depth, ?), structure (equilibrium distance, rm) and spectroscopy (anharmonic frequency, ?):? = A? (? /?)1/ 2 /rm + B?? /rm 3 , where A and B are constants depending on the underlying PEF. This more general case of Badgers rule has been validated using the experimentally measured frequencies of the hydrogen bonded OH stretching vibrations in the halide-water series.

Werhahn, Jasper C.; Akase, Dai; Xantheas, Sotiris S.

2014-08-14T23:59:59.000Z

320

A numerical study of the supply mode effects on high-pressure mercury discharge lamp dynamic thermal behavior  

SciTech Connect

This paper presents a numerical study of the dynamic behavior of high-pressure mercury discharge lamp as a function of supply mode. Bidimensional time-dependent equations have been solved by using a semi-implicit finite-element code. The model has been developed in the frame of the local thermodynamic equilibrium hypothesis. After validation by using experimental data from the literature, this model was applied to analyze the effects of some key parameters such as frequency for an ac arc current and the ratio cycle parameter for square arc-current wave form on the convective process. The results obtained have been used to analyze the dynamic thermal behavior of high-pressure mercury plasma (pressure equal to 0.3 MPa) working under currents widely different in frequency and wave form.

Kaziz, S.; Ahmed, R. Ben; Araoud, Z.; Gazzah, M.H.; Charrada, K.; Said, R. [EMIR, IPEIM, route de Skanes, 5019 Monastir (Tunisia); FSM, avenue de l'environnement, 5019 Monastir (Tunisia); EMIR, IPEIM, route de Skanes, 5019 Monastir (Tunisia)

2005-06-15T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Jade Sky Technologies Partners with CLTC on LED Replacement Lamp Upgrade Project UC Davis' California Lighting Technology Center will utilize Jade Sky Technologies' driver ICs to help spur  

E-Print Network (OSTI)

Jade Sky Technologies Partners with CLTC on LED Replacement Lamp Upgrade Project UC Davis of cost-effective, easy-to-use LED lighting solutions Milpitas, Calif. ­ October 15, 2013 ­ Jade Sky Technologies (JST), a clean-tech start-up manufacturer of driver ICs for LED lighting applications, announces

California at Davis, University of

322

15th Semi-Annual Report to Congress on Appliance Energy Efficiency...  

Energy Savers (EERE)

final rules amended energy conservation standards for metal halide lamp fixtures and test procedures for residential clothes dryers, residential plumbing products, television...

323

Facility for high-heat flux testing of irradiated fusion materials and components using infrared plasma arc lamps  

Science Journals Connector (OSTI)

A new high-heat flux testing (HHFT) facility using water-wall stabilized high-power high-pressure argon plasma arc lamps (PALs) has been developed for fusion applications. Itcan accommodate irradiated plasma facing component materials and sub-size mock-up divertor components. Two PALs currently available at Oak Ridge National Laboratorycan provide maximum incident heat fluxes of 4.2 and 27MWm?2, which are prototypic of fusion steady state heat flux conditions, over a heated area of 9?12 and 1?10cm2, respectively. The use of PAL permits the heat source to be environmentally separated from the components of the test chamber, simplifying the design to accommodate safe testing of low-level irradiated articles and materials under high-heat flux. Issues related to the operation and temperature measurements during testing of tungsten samples are presented and discussed. The relative advantages and disadvantages of this photon-based HHFT facility are compared to existing e-beam and particle beam facilities used for similar purposes.

Adrian S Sabau; Evan K Ohriner; Jim Kiggans; David C Harper; Lance L Snead; Charles R Schaich

2014-01-01T23:59:59.000Z

324

Facility for high heat flux testing of irradiated fusion materials and components using infrared plasma arc lamps  

SciTech Connect

A new high-heat flux testing facility using water-wall stabilized high-power high-pressure argon Plasma Arc Lamps (PALs) has been developed for fusion applications. It can handle irradiated plasma facing component materials and mock-up divertor components. Two PALs currently available at ORNL can provide maximum incident heat fluxes of 4.2 and 27 MW/m2 over a heated area of 9x12 and 1x10 cm2, respectively, which are fusion-prototypical steady state heat flux conditions. The facility will be described and the main differences between the photon-based high-heat flux testing facilities, such as PALs, and the e-beam and particle beam facilities more commonly used for fusion HHF testing are discussed. The components of the test chamber were designed to accommodate radiation safety and materials compatibility requirements posed by high-temperature exposure of low levels irradiated tungsten articles. Issues related to the operation and temperature measurements during testing are presented and discussed.

Sabau, Adrian S [ORNL] [ORNL; Ohriner, Evan Keith [ORNL] [ORNL; Kiggans, Jim [ORNL] [ORNL; Harper, David C [ORNL] [ORNL; Snead, Lance Lewis [ORNL] [ORNL; Schaich, Charles Ross [ORNL] [ORNL

2014-01-01T23:59:59.000Z

325

DOE CALiPER Program, Report 20.1 Subjective Evaluation of Beam Quality, Shadow Quality, and Color Quality for LED PAR38 Lamps  

SciTech Connect

This report focuses on human-evaluated characteristics, including beam quality, shadow quality, and color quality. Using a questionnaire that included rank ordering, opinions on 27 of the Report 20 PAR38 lamps were gathered during a demonstration event for members of the local Illuminating Engineering Society (IES) chapter. This was not a rigorous scientific experiment, and the data should not be extrapolated beyond the scope of the demonstration. The results suggest that many of the LED products compared favorably to halogen PAR38 benchmarks in all attributes considered. LED lamps using a single-emitter design were generally preferred for their beam quality and shadow quality, and the IES members ranking of color quality did not always match the rank according to the color rendering index (CRI).

Royer, Michael P.; Poplawski, Michael E.; Miller, Naomi J.

2013-10-01T23:59:59.000Z

326

Results from the Carbon-Land Model Intercomparison Project (C-LAMP) and Availability of the Data on the Earth System Grid (ESG)  

SciTech Connect

This paper describes the Carbon-Land Model Intercomparison Project (C-LAMP) being carried out through a collaboration between the Community Climate System Model (CCSM) Biogeochemistry Working Group, a DOE SciDAC-2 project, and the DOE Program for Climate Model Diagnosis and Intercomparison (PCMDI). The goal of the project is to intercompare terrestrial biogeochemistry models running within the CCSM framework to determine the best set of processes to include in future versions of CCSM. As a part of the project, observational datasets are being collected and used to score the scientific performance of these models following a well-defined set of metrics. In addition, metadata standards for terrestrial biosphere models are being developed to support archival and distribution of the C-LAMP model output via the Earth System Grid (ESG). Progress toward completion of this project and preliminary results from the first set of experiments are reported.

Hoffman, Forrest M [ORNL; Covey, Curtis [Lawrence Livermore National Laboratory (LLNL); Fung, Inez [University of California, Berkeley; Randerson, Jim [University of California, Irvine; Thornton, Peter [National Center for Atmospheric Research (NCAR); Lee, Jeff [National Center for Atmospheric Research (NCAR); Rosenbloom, Nan [National Center for Atmospheric Research (NCAR); Stockli, Reto [Colorado State University, Fort Collins; Running, Steven [University of Montana, Missoula; Bernholdt, David E [ORNL; Williams, Dean [Lawrence Livermore National Laboratory (LLNL)

2007-01-01T23:59:59.000Z

327

DOE/EA-1664: Environmental Assessment for 10 CFR 430 Energy Conservation Standards: Energy Conservation Standards for Fluorescent and Incandescent Lamps (June 2009)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 Environmental Assessment for 10 CFR Part 430 Energy Conservation Standards: Energy Conservation Standards for Fluorescent and Incandescent Lamps June 2009 16-i CHAPTER 16. ENVIRONMENTAL ASSESSMENT TABLE OF CONTENTS 16.1 INTRODUCTION ......................................................................................................... 16-1 16.2 AIR EMISSIONS ANALYSIS...................................................................................... 16-1 16.2.1 Air Emissions Descriptions............................................................................................ 16-1 16.2.2 Air Quality Regulation................................................................................................... 16-3 16.2.3 Global Climate Change..................................................................................................

328

Phosphors for LED lamps  

SciTech Connect

A phosphor, a phosphor blend including the phosphor, a phosphor prepared by a process, and a lighting apparatus including the phosphor blend are disclosed. The phosphor has the formula (Ca.sub.1-p-qCe.sub.pK.sub.q).sub.xSc.sub.y(Si.sub.1-rGa.sub.r).sub.zO.su- b.12+.delta. or derived from a process followed using disclosed amounts of reactants. In the formula, (0

Murphy, James Edward; Manepalli, Satya Kishore; Kumar, Prasanth Nammalwar

2013-08-13T23:59:59.000Z

329

The Carbon-Land Model Intercomparison Project (C-LAMP): A Model-Data Comparison System for Evaluation of Coupled Biosphere-Atmosphere Models  

SciTech Connect

The need to capture important climate feebacks in general circulation models (GCMs) has resulted in new efforts to include atmospheric chemistry and land and ocean biogeochemistry into the next generation of production climate models, now often referred to as Earth System Models (ESMs). While many terrestrial and ocean carbon models have been coupled to GCMs, recent work has shown that such models can yield a wide range of results, suggesting that a more rigorous set of offline and partially coupled experiments, along with detailed analyses of processes and comparisons with measurements, are warranted. The Carbon-Land Model Intercomparison Project (C-LAMP) provides a simulation protocol and model performance metrics based upon comparisons against best-available satellite- and ground-based measurements (Hoffman et al., 2007). C-LAMP provides feedback to the modeling community regarding model improvements and to the measurement community by suggesting new observational campaigns. C-LAMP Experiment 1 consists of a set of uncoupled simulations of terrestrial carbon models specifically designed to examine the ability of the models to reproduce surface carbon and energy fluxes at multiple sites and to exhibit the influence of climate variability, prescribed atmospheric carbon dioxide (CO{sub 2}), nitrogen (N) deposition, and land cover change on projections of terrestrial carbon fluxes during the 20th century. Experiment 2 consists of partially coupled simulations of the terrestrial carbon model with an active atmosphere model exchanging energy and moisture fluxes. In all experiments, atmospheric CO{sub 2} follows the prescribed historical trajectory from C{sup 4}MIP. In Experiment 2, the atmosphere model is forced with prescribed sea surface temperatures (SSTs) and corresponding sea ice concentrations from the Hadley Centre; prescribed CO{sub 2} is radiatively active; and land, fossil fuel, and ocean CO{sub 2} fluxes are advected by the model. Both sets of experiments have been performed using two different terrestrial biogeochemistry modules coupled to the Community Land Model version 3 (CLM3) in the Community Climate System Model version 3 (CCSM3): The CASA model of Fung, et al., and the carbon-nitrogen (CN) model of Thornton. Comparisons against Ameriflus site measurements, MODIS satellite observations, NOAA flask records, TRANSCOM inversions, and Free Air CO{sub 2} Enrichment (FACE) site measurements, and other datasets have been performed and are described in Randerson et al. (2009). The C-LAMP diagnostics package was used to validate improvements to CASA and CN for use in the next generation model, CLM4. It is hoped that this effort will serve as a prototype for an international carbon-cycle model benchmarking activity for models being used for the Inter-governmental Panel on Climate Change (IPCC) Fifth Assessment Report. More information about C-LAMP, the experimental protocol, performance metrics, output standards, and model-data comparisons from the CLM3-CASA and CLM3-CN models are available at http://www.climatemodeling.org/c-lamp.

Hoffman, Forrest M [ORNL; Randerson, Jim [University of California, Irvine; Thornton, Peter E [ORNL; Mahowald, Natalie [Cornell University; Bonan, Gordon [National Center for Atmospheric Research (NCAR); Running, Steven [University of Montana, Missoula; Fung, Inez [University of California, Berkeley

2009-01-01T23:59:59.000Z

330

2014-12-05 Issuance: Energy Conservation Standard for General Service Lamps; Notice of Public Meeting and Availability of the Preliminary Technical Support Document  

Energy.gov (U.S. Department of Energy (DOE))

This document is a pre-publication Federal Register notice of public meeting and availability of the preliminary technical support document regarding energy conservation standards for general service lamps, as issued by the Deputy Assistant Secretary for Energy Efficiency on December 5, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

331

Tungsten and tungsten alloy powder metallurgy: Powder production and applications excluding lamps. (Latest citations from the US Patent bibliographic file with exemplary claims). Published Search  

SciTech Connect

The bibliography contains citations of selected patents concerning the preparation of metallic and ceramic powders of tungsten and tungsten alloys, including applications of these materials. The hydrogen reduction of tungsten compounds together with alloying element compounds produce forms with characteristics of high density, hardness, wear resistance, high melting points, and abrasiveness. Topics include production of cathodes, heaters, filament wires, electrical contacts, acoustic absorbers, high-density sheets and coatings, hard penetrators, and tungsten carbide and metallized ceramics. Tungsten halogen lamps are examined in a separate bibliography.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

NONE

1997-01-01T23:59:59.000Z

332

Tungsten and tungsten alloy powder metallurgy: Powder production and applications excluding lamps. (Latest citations from the US Patent database). Published Search  

SciTech Connect

The bibliography contains citations of selected patents concerning the preparation of metallic and ceramic powders of tungsten and tungsten alloys, including applications of these materials. The hydrogen reduction of tungsten compounds together with alloying element compounds produce forms with characteristics of high density, hardness, wear resistance, high melting points, and abrasiveness. Topics include production of cathodes, heaters, filament wires, electrical contacts, acoustic absorbers, high-density sheets and coatings, hard penetrators, and tungsten carbide and metallized ceramics. Tungsten halogen lamps are examined in a separate bibliography. (Contains a minimum of 97 citations and includes a subject term index and title list.)

Not Available

1993-05-01T23:59:59.000Z

333

Tungsten and tungsten alloy powder metallurgy: Powder production and applications excluding lamps. (Latest citations from the US Patent bibliographic file with exemplary claims). Published Search  

SciTech Connect

The bibliography contains citations of selected patents concerning the preparation of metallic and ceramic powders of tungsten and tungsten alloys, including applications of these materials. The hydrogen reduction of tungsten compounds together with alloying element compounds produce forms with characteristics of high density, hardness, wear resistance, high melting points, and abrasiveness. Topics include production of cathodes, heaters, filament wires, electrical contacts, acoustic absorbers, high-density sheets and coatings, hard penetrators, and tungsten carbide and metallized ceramics. Tungsten halogen lamps are examined in a separate bibliography.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

NONE

1995-12-01T23:59:59.000Z

334

Tungsten and tungsten alloy powder metallurgy: Powder production and applications excluding lamps. (Latest citations from the US Patent bibliographic file with exemplary claims). Published Search  

SciTech Connect

The bibliography contains citations of selected patents concerning the preparation of metallic and ceramic powders of tungsten and tungsten alloys, including applications of these materials. The hydrogen reduction of tungsten compounds together with alloying element compounds produce forms with characteristics of high density, hardness, wear resistance, high melting points, and abrasiveness. Topics include production of cathodes, heaters, filament wires, electrical contacts, acoustic absorbers, high-density sheets and coatings, hard penetrators, and tungsten carbide and metallized ceramics. Tungsten halogen lamps are examined in a separate bibliography. (Contains a minimum of 115 citations and includes a subject term index and title list.)

NONE

1995-02-01T23:59:59.000Z

335

Microsoft Word - FOR WEB - Universal 26004 NND based on GE 4901, 2609 v3.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

BEFORE THE BEFORE THE U.S. DEPARTMENT OF ENERGY Washington, D.C. 20585 In the Matter of: Universal Lighting Technologies, Inc. (fluorescent lamp ballasts) ) ) ) ) ) Case Number: 2013-SE-26004 Issued: September 6, 2013 NOTICE OF NONCOMPLIANCE DETERMINATION Fluorescent lamp ballasts are covered products subject to federal energy conservation standards as described in 42 U.S.C. §§ 6292(a)(13), 6295(g) and 10 C.F.R. § 430.32(m). Specifically, fluorescent lamp ballasts designed for use in connection with one F40T12 lamp and sold by the manufacturer on or after July 1, 2005, are subject to a minimum ballast efficacy factor of 2.29 and a minimum power factor of 0.90. 42 U.S.C. § 6295(g)(8) and 10 C.F.R. § 430.32(m). Manufacturers and private labelers are prohibited from distributing covered products that do not

336

Power Conditioning and Control Applications for Energy Conservation  

E-Print Network (OSTI)

Electrical power conditioning and control (PCC) systems are finding cost effective applications in AC motor drives, lamp ballasts and power supplies. Substantial system efficiency improvements are being realized when the appropriate PCC system...

Brushwood, J. S.

1982-01-01T23:59:59.000Z

337

Keystone: Order (2013-CE-2601)  

Energy.gov (U.S. Department of Energy (DOE))

DOE ordered Keystone Technologies, LLC to pay a $8,000 civil penalty after finding Keystone had failed to certify that certain models of fluorescent lamp ballasts comply with the applicable energy conservation standards.

338

Energy Engineering Analysis Program (EEAP), Fort Bliss headquarters building, lighting retrofit, Fort Bliss, El Paso, Texas  

SciTech Connect

The purpose of this study is to analyze the use of high efficiency fluorescent lighting with energy efficient lamps and electronic ballast for the Headquarters Building (Bldg. number 2) at Fort Bliss.

NONE

1993-02-01T23:59:59.000Z

339

Reading Municipal Light Department - Business Lighting Rebate Program |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reading Municipal Light Department - Business Lighting Rebate Reading Municipal Light Department - Business Lighting Rebate Program Reading Municipal Light Department - Business Lighting Rebate Program < Back Eligibility Agricultural Commercial Fed. Government Industrial Institutional Local Government Nonprofit Schools State Government Savings Category Appliances & Electronics Commercial Lighting Lighting Maximum Rebate Commercial Customers: $10,000 per calendar year Municipal Customers: $15,000 per calendar year Program Info State Massachusetts Program Type Utility Rebate Program Rebate Amount T-8/T-5 Lamp with Electronic Ballasts: $11 - $35/fixture Interior High Output Lamp with Electronic Ballasts: $100/fixture De-lamping: $4 - $9/lamp Lighting Sensors: $20/sensor LED Exit Signs: $20/fixture Provider Incentive Programs

340

Calculation of rate constants for dissociative attachment of low-energy electrons to hydrogen halides HCl, HBr, and HI and their deuterated analogs  

Science Journals Connector (OSTI)

Calculations of rate constants for the process of dissociative attachment of low-energy electrons to hydrogen halides HCl, HBr, and HI and for the reverse process of associative detachment based on the nonlocal resonance model are reported. The calculated data are of importance for the modeling of plasma processes, environmental chemistry, etc. The calculated dissociative attachment rate constants are found to be in good agreement with existing experimental data. It is shown that at low temperatures the rate constants are very sensitive to small changes of the parameters of the nonlocal resonance model used for the calculation of the rate constants and represent a severe test of the theory. The isotopic effect and its dependence on the temperature is also discussed. The calculations of rate constants for the reverse process of associative detachment are also reported and discussed.

Karel Houfek; Martin ?ek; Ji? Hor?ek

2002-12-06T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Fabrication of large-volume, low-cost ceramic lanthanum halide scintillators for gamma ray detection : final report for DHS/DNDO/TRDD project TA-01-SL01.  

SciTech Connect

This project uses advanced ceramic processes to fabricate large, optical-quality, polycrystalline lanthanum halide scintillators to replace small single crystals produced by the conventional Bridgman growth method. The new approach not only removes the size constraint imposed by the growth method, but also offers the potential advantages of both reducing manufacturing cost and increasing production rate. The project goal is to fabricate dense lanthanum halide ceramics with a preferred crystal orientation by applying texture engineering and solid-state conversion to reduce the thermal mechanical stress in the ceramic and minimize scintillation light scattering at grain boundaries. Ultimately, this method could deliver the sought-after high sensitivity and <3% energy resolution at 662 keV of lanthanum halide scintillators and unleash their full potential for advanced gamma ray detection, enabling rapid identification of radioactive materials in a variety of practical applications. This report documents processing details from powder synthesis, seed particle growth, to final densification and texture development of cerium doped lanthanum bromide (LaBr{sub 3}:Ce{sup +3}) ceramics. This investigation demonstrated that: (1) A rapid, flexible, cost efficient synthesis method of anhydrous lanthanum halides and their solid solutions was developed. Several batches of ultrafine LaBr{sub 3}:Ce{sup +3} powder, free of oxyhalide, were produced by a rigorously controlled process. (2) Micron size ({approx} 5 {micro}m), platelet shape LaBr{sub 3} seed particles of high purity can be synthesized by a vapor phase transport process. (3) High aspect-ratio seed particles can be effectively aligned in the shear direction in the ceramic matrix, using a rotational shear-forming process. (4) Small size, highly translucent LaBr{sub 3} (0.25-inch diameter, 0.08-inch thick) samples were successfully fabricated by the equal channel angular consolidation process. (5) Large size, high density, translucent LaBr{sub 3} ceramics samples (3-inch diameter, > 1/8-inch thick) were fabricated by hot pressing, demonstrating the superior manufacturability of the ceramic approach over single crystal growth methods in terms of size capability and cost. (6) Despite all these advances, evidence has shown that LaBr{sub 3} is thermally unstable at temperatures required for the densification process. This is particularly true for material near the surface where lattice defects and color centers can be created as bromine becomes volatile at high temperatures. Consequently, after densification these samples made using chemically prepared ultrafine powders turned black. An additional thermal treatment in a flowing bromine condition proved able to reduce the darkness of the surface layer for these densified samples. These observations demonstrated that although finer ceramic powders are desirable for densification due to a stronger driving force from their large surface areas, the same desirable factor can lead to lattice defects and color centers when these powders are densified at higher temperatures where material near the surface becomes thermally unstable.

Boyle, Timothy J.; Ottley, Leigh Anna M.; Yang, Pin; Chen, Ching-Fong; Sanchez, Margaret R.; Bell, Nelson Simmons

2008-10-01T23:59:59.000Z

342

Effects of stereochemistry and ?-substituents on the rates of vinylic SN2 reaction of hypervalent vinyl(phenyl)-?3-iodanes with tetrabutylammonium halides  

Science Journals Connector (OSTI)

Both stereoisomers of ?-(2-phenylethoxy)vinyl-?3-iodane and (Z)-?-aroyloxyvinyl-?3-iodane were prepared stereoselectively. These substituted vinyl-?3-iodanes undergo nucleophilic vinylic substitutions with n-Bu4NX (X=Cl, Br, I) under mild conditions, yielding vinyl halides. The observed inversion of configuration at the ipso vinylic carbon atom is compatible with a concerted vinylic SN2 mechanism. Kinetic measurements indicated that the rates for vinylic SN2 reaction of (Z)-vinyl-?3-iodane are greater than those of the E-isomer, probably because of the higher ground state energy of the Z-isomer. Electronic effects of ?-substituents of vinyl-?3-iodanes in the vinylic SN2 reaction are also discussed.

Kazunori Miyamoto; Takuji Okubo; Masaya Hirobe; Munetaka Kunishima; Masahito Ochiai

2010-01-01T23:59:59.000Z

343

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)  

SciTech Connect

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and ?-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 129 ppm (5274.9 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.917.6 ppm (7987.4 71.9 Bq/kg) and 17.2 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by ?- spectrometry were 1156 ppm (4728 22 Bq/kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of {sup 232}Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 0.6% and 4.7 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted.

AL-Areqi, Wadeeah M., E-mail: walareqi@yahoo.com; Majid, Amran Ab., E-mail: walareqi@yahoo.com; Sarmani, Sukiman, E-mail: walareqi@yahoo.com [Nuclear Science Programme, School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi (Malaysia)

2014-02-12T23:59:59.000Z

344

Effect of potassium halide salts on mutual solubility of water+aromatic hydrocarbons liquidliquid interface studied with surface and interfacial tensions  

Science Journals Connector (OSTI)

Abstract Surface tension (?, mN/m) of benzene, toluene and ethylbenzene (EB) aromatic hydrocarbons (AHCs, low density liquids, LDL) and interfacial tension (IFT, mN/m) both with water and aqueous 0.1, 0.5, 1.0molkg?1 KF, KCl, KBr, KI (high density liquids, HDL) separately at 303.15K are reported. Contributions of CH3 and CH2CH3 of toluene and EB to hydrophobic interactions are calculated from ?toluene?benzene and ?EB?benzene, respectively. \\{IFTs\\} of water+AHCs liquidliquid interfaces (LLI) are as toluene (34.71)>EB (32.35)>benzene (32.32mNm?1), with a ~32.32mNm?1 decrease from 71.40mNm?1 of water. \\{AHCs\\} with hyperconjugation (HC) and positive inductive effects (+ve IE) with toluene and EB LLI have reduced IFT by 39.08, 2.39, ?1.56mNm?1, respectively. The effects of ?-conjugation, H, CH3 and CH2CH3 on surface tension are calculated as ?-conjugation=?(IFTairliquid?IFTAPHSbenzene), CH3=?(IFTAPHStoluene?IFTAPHSbenzene). The effects of halide salts on hypercongugation H(CH3)/3, CH2CH3 are obtained from ?(IFTAPHSEB ?IFTAPHSbenzene).

Man Singh

2014-01-01T23:59:59.000Z

345

Fluorescent Lighting Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fluorescent Lighting Basics Fluorescent Lighting Basics Fluorescent Lighting Basics October 17, 2013 - 5:39pm Addthis Light from a fluorescent lamp is first created by an electric current conducted through an inert gas producing ultraviolet light that is invisible to the human eye. The ultraviolet light in turn interacts with special blends of phosphors coating the interior surface of the fluorescent lamp tube that efficiently converts the invisible light into useful white light. Fluorescent lamps require a special power supply called a ballast that is needed to regulate lamp operating current and provide a compatible start-up voltage. Electronic ballasts perform the same function as a magnetic ballast but outperform the outdated magnetic products by operating at a very high frequency that eliminates flicker and noise while

346

Lighting Group: Sources and Ballasts: OLED Cathodes  

NLE Websites -- All DOE Office Websites (Extended Search)

OLED Cathodes OLED Cathodes Development of New Cathodes for OLED's Objective The objective of this project is to develop improved cathodes for use in organic light emitting diodes (OLEDs). Approach A major challenge for organic light emitting diode (OLED) technology is to improve electron injection into the organic electroluminescent layer, which limits the efficiency of the device and the luminous flux per unit area. This project aims at overcoming such barriers by developing “structured cathodes” based on functional materials (nanotubes and nanoclusters) with characteristic size smaller than the optical wavelength. The incorporation of such nanostructured cathodes in OLEDs can significantly improve device efficiency by lowering operating voltage, and increase device stability and light extraction.

347

Measurement of optical efficiency of fluorescent luminaires  

SciTech Connect

By controlling the lamp wall temperature of fluorescent lamps with a Peltier device, the optical efficiency of luminaires can be measured directly. Measurements of the fixture efficiency for a luminaire can vary by over 8% depending upon the lamp-ballast system used in the measurement. The authors suggest that optical efficiency may be an improved metric for evaluating fixture designs. 6 refs., 3 figs., 5 tabs.

Verderber, R.R.; Morse, O.; Rubinstein, F.; Siminovitch, M.

1987-01-01T23:59:59.000Z

348

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

Metal Halide Lamp Fixtures Energy Conservation Standard Metal Halide Lamp Fixtures Energy Conservation Standard Sign up for e-mail updates on regulations for this and other products The Department of Energy (DOE) is considering establishing new and amended energy conservation standards for metal halide lamp fixtures (MHLF). This activity is mandated by the Energy Policy and Conservation Act (42 U.S.C. 6291-6309 seq). Recent Updates | Public Meeting Information | Submitting Public Comments | Milestones and Documents | Related Rulemakings | Statutory Authority | Contact Information Recent Updates DOE published a notice of proposed rulemaking regarding energy conservation standards for metal halide lamp fixtures. 78 FR 51463 (August 20, 2013). Public Meeting Information A public meeting was held on September 27, 2013.

349

Order Code RL34294 Energy Independence and Security Act of 2007  

E-Print Network (OSTI)

includes residential refrigerators, freezers, refrigerator-freezers, metal halide lamps, and commercial walk-in coolers and freezers. ! Repeal of Oil and Gas Tax Incentives. The enacted law includes repeal

Laughlin, Robert B.

350

Effects of Bradyrhizobium japonicum and Soybean (Glycine max (L.) Merr.) Phosphorus Nutrition on Nodulation and Dinitrogen Fixation  

Science Journals Connector (OSTI)

...not used to evaluate treatment effects. Greenhouse experiment. The greenhouse experiment was designed to evaluate the...blocks. The plants were grown in the greenhouse with supplemental lighting provided by metal halide lamps to extend...

Michael D. Mullen; Daniel W. Israel; A. G. Wollum II

1988-10-01T23:59:59.000Z

351

Data:44cdd6cb-13cb-4fdb-bfd4-60e5a1b2d9b6 | Open Energy Information  

Open Energy Info (EERE)

cdd6cb-13cb-4fdb-bfd4-60e5a1b2d9b6 cdd6cb-13cb-4fdb-bfd4-60e5a1b2d9b6 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service-Post Top Fixtures- (Traditional HPS 100W) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

352

Data:86cf7401-9b8c-4e5c-b5bd-847bc075d6f2 | Open Energy Information  

Open Energy Info (EERE)

401-9b8c-4e5c-b5bd-847bc075d6f2 401-9b8c-4e5c-b5bd-847bc075d6f2 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service- Security Lights- (175 W MV with Pole) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

353

Data:C03dd3ea-4e0e-444d-aa1d-553b55c724e2 | Open Energy Information  

Open Energy Info (EERE)

dd3ea-4e0e-444d-aa1d-553b55c724e2 dd3ea-4e0e-444d-aa1d-553b55c724e2 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Crisp County Power Comm Effective date: 2012/01/01 End date if known: Rate name: Rental Light Service-Post Top Fixtures- (Galleria HPS 100W) Sector: Lighting Description: Applicable only to outdoor lighting by ballast operated vapor lamp fixtures, either Mercury Vapor, Pressure Sodium, or Metal Halide. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

354

Tungsten and tungsten-alloy powder metallurgy: Powder production and applications-excluding lamps. November 1971-July 1989 (Citations from the US Patent data base). Report for November 1971-July 1989  

SciTech Connect

This bibliography contains citations of selected patents concerning the preparation of metallic and ceramic powders of tungsten and tungsten alloys including various applications of these materials. The hydrogen reduction of tungsten compounds together with alloying-element compounds produce forms with characteristics of high density, hardness, wear resistance, high melting points, and abrasiveness. Topics include production of various cathodes, heaters, filament wires, electrical contacts, acoustic absorbers, high-density sheets and coatings, hard penetrators, and tungsten carbide and metallized ceramics. Tungsten halogen lamps are examined in a separate bibliography. (Contains 60 citations fully indexed and including a title list.)

Not Available

1989-10-01T23:59:59.000Z

355

Fluorination of the cyanogen halides  

E-Print Network (OSTI)

silver has a coordination number of 12 two, one might speculate that a coordination compound la formed with a silver fluoride on both ends of the cyanogen todlde molecule. This arrangement would satisfy one silver with a fluoride and a cyanide... copper caps which were sliver soldered ln place. Copper tubing entrance and exit tubes were silver soldered to the top of the pot. The pipe union formed a leak proof system which could be assembled with reactants, and disassembled after reaction...

Ward, Raymond Anthony

1960-01-01T23:59:59.000Z

356

BEFORE THE U.S. DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Philips Lighting Electronics N. A. Philips Lighting Electronics N. A. (fluorescent lamp ballasts) ) ) ) ) ) Case Number: 2012-SE-2605 Issued: August 31, 2012 NOTICE OF NONCOMPLIANCE DETERMINATION Fluorescent lamp ballasts are covered products subject to federal energy conservation standards as described in 42 U.S.C. §§ 6292(a)(13), 6295(g) and IO C.P.R.§ 430.32(m). Manufacturers and private labelers are prohibited from distributing covered products that do not comply with the applicable conservation standards. 10 C.P.R. § 429.102(a)(6); 42 U.S. C.§ 6302(a)(5). In February of this year, Philips Lighting Electronics N. A. ("Philips") submitted certification report CCMS # 9935, ce1tifying that fluorescent lamp ballast basic model VEL-I S40-SC was not in compliance with the applicable energy conservation standards. Philips notified the U.S.

357

INSTITUTE OF PHYSICS PUBLISHING PLASMA SOURCES SCIENCE AND TECHNOLOGY Plasma Sources Sci. Technol. 12 (2003) 821 PII: S0963-0252(03)55523-2  

E-Print Network (OSTI)

as multi-atmosphere thermal arcs, during their starting phase the lamps are moderate pressure glowINSTITUTE OF PHYSICS PUBLISHING PLASMA SOURCES SCIENCE AND TECHNOLOGY Plasma Sources Sci. Technol. 12 (2003) 8­21 PII: S0963-0252(03)55523-2 Breakdown processes in metal halide lamps Brian Lay1

Kushner, Mark

358

BEFORE THE U.S. DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Simkar Corporation Simkar Corporation (metal halide lamp fixtures) ) ) ) ) ) Case Number: 2012-SE-5408 NOTICE OF PROPOSED CIVIL PENALTY Date issued: November 21,2012 Number of alleged violations: 326 Maximum possible assessment: $65,200 Proposed civil penalty: $65,200 The U.S. Department of Energy ("DOE") Office of the General Counsel, Office of Enforcement, alleges that Simkar Corporation ("Simkar") has violated certain provisions of the Energy Policy and Conservation Act, 42 U.S. C.§ 6291 et seq. ("the Act"), and 10 C.F.R. Parts 429,430, and 431. Specifically, DOE alleges: 1. A metal halide lamp fixture is a "covered product" as defined in 42 U.S. C.§ 6292(a)(19) and 10 C.F.R. § 430.2; 2. Effective January I, 2009, each metal halide lamp fixture with a pulse-stmt metal halide

359

CX-008415: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

15: Categorical Exclusion Determination 15: Categorical Exclusion Determination CX-008415: Categorical Exclusion Determination California-City-Westminster CX(s) Applied: B1.32, B2.5, B5.1 Date: 07/10/2012 Location(s): California Offices(s): Energy Efficiency and Renewable Energy Conduct lighting retrofits in city buildings (City Hall, Council Chambers, Community Center/Senior Center, and Rose Center) which includes replacing some existing fluorescent fixtures with T8 lamps and low-watt electronic ballasts, replacing some 1st generation T8 fluorescent fixtures with T8 lamps and low-watt electronic ballasts, replacing some incandescent fixtures with compact fluorescent lamps or new PL-lamp fixtures, and adding occupancy sensor controls and daylight controls to interior lighting fixtures in some of the facilities.

360

U.S. Department of Energy NEPA Categorical Exclusion Determination Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CA-City-Westminster CA-City-Westminster Location: City Westminster CA American Recovery and Reinvestment Act: Proposed Action or Project Description: 1) Conduct lighting retrofits in city buildings (City Hall, Council Chambers, Community Center/Senior Center, and Rose Center) which includes replacing some existing fluorescent fixtures with T8 lamps and low-watt electronic ballasts, replacing some 1st generation T8 fluorescent fixtures with T8 lamps and low- watt electronic ballasts, replacing some incandescent fixtures with compact fluorescent lamps or new PL- lamp fixtures, and adding occupancy sensor controls and daylight controls to interior lighting fixtures in some of the facilities; 2) replace tennis court light fixtures at Park West and Bolsa Chica Park; 3) furnish

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Effects of partial anion substitution on the thermoelectric properties of silver(I) chalcogenide halides in the system Ag{sub 5}Q{sub 2}X with Q=Te, Se and S and X=Br and Cl  

SciTech Connect

A selection of mixed conducting silver chalcogenide halides of the general formula Ag{sub 5}Q{sub 2}X with Q=sulfur, selenium and tellurium and X=chlorine and bromine has been investigated due to their thermoelectric properties. Recently, the ternary counterpart Ag{sub 5}Te{sub 2}Cl showed a defined d{sup 10}-d{sup 10} interaction in the disordered cation substructure at elevated temperatures where Ag{sub 5}Te{sub 2}Cl is present in its high temperature {alpha}-phase. A significant drop of the thermal diffusivity has been observed during the {beta}-{alpha} phase transition reducing the values from 0.12 close to 0.08 mm{sup 2} s{sup -1}. At the same transition the thermopower reacts on the increasing silver mobility and jumps towards less negative values. Thermal conductivities, thermopower and thermal diffusivity of selected compounds with various grades of anion substitution in Ag{sub 5}Q{sub 2}X were determined around the silver-order/disorder {beta}-{alpha} phase transition. A formation of attractive interactions could be observed for selenium substituted phases while no effect was detected for bromide and sulfide samples. Depending on the grade and type of substitution the thermopower changes significantly at and after the {beta}-{alpha} phase transition. Thermal conductivities are low reaching values around 0.2-0.3 W m{sup -1} K{sup -1} at 299 K. Partial anion exchange can substantially tune the thermoelectric properties in Ag{sub 5}Q{sub 2}X phases. -- Graphical abstract: A structure section of the {alpha}-Ag{sub 5}Te{sub 2}Cl structure type and the thermopower evolution of Ag{sub 5}Te{sub 2}Cl{sub 0.4}Br{sub 0.6} undergoing a silver ion order/disorder phase transition. Display Omitted Research highlights: > We report on thermoelectric properties of silver(I) chalcogenide halides. > We examine thermopower, thermal diffusivity and thermal behavior. > Silver mobility, phase transitions and order/disorder phenomena are discussed. > Partial anion exchange can tune thermoelectric properties significantly.

Eckstein, Nadine [TU Muenchen, Lichtenbergstrasse 4, Garching (Germany); Nilges, Tom, E-mail: tom.nilges@lrz.tum.d [TU Muenchen, Lichtenbergstrasse 4, Garching (Germany); Decourt, Rodolphe; Bobet, Jean-Louis; Chevalier, Bernard [CNRS, Universite de Bordeaux, ICMCB, Avenue du Docteur Schweitzer 87, 33608 PESSAC cedex (France)

2011-04-15T23:59:59.000Z

362

Types of Lighting in Commercial Buildings - Lighting Types  

U.S. Energy Information Administration (EIA) Indexed Site

Lighting Types Lighting Types The following are the most widely used types of lighting equipment used in commercial buildings. Characteristics such as energy efficiency, light quality, and lifetime vary by lamp type. Standard Fluorescent A fluorescent lamp consists of a sealed gas-filled tube. The gas in the tube consists of a mixture of low pressure mercury vapor and an inert gas such as argon. The inner surface of the tube has a coating of phosphor powder. When an electrical current is applied to electrodes in the tube, the mercury vapor emits ultraviolet radiation which then causes the phosphor coating to emit visible light (the process is termed fluorescence). A ballast is required to regulate and control the current and voltage. Two types of ballasts are used, magnetic and electronic. Electronic ballasts

363

DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

[6450-01-P] [6450-01-P] DEPARTMENT OF ENERGY 10 CFR Part 430 [Docket Number EERE-2007-BT-STD-0016] RIN 1904-AB50 Energy Conservation Program: Energy Conservation Standards for Fluorescent Lamp Ballasts AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION: Finding of No Significant Impact: Energy Conservation Program. SUMMARY: The Energy Policy and Conservation Act of 1975 (EPCA), as amended, prescribes energy conservation standards for various consumer products and certain commercial and industrial equipment, including fluorescent lamp ballasts (hereafter referred to as ballasts). EPCA also requires the U.S. Department of Energy (DOE) to determine whether more-stringent standards would be technologically feasible and economically justified, and would save a

364

Microsoft Word - EA-1881-FEA-2011.docx  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Program: Energy Conservation Standards for Fluorescent Lamp Ballasts DOE/EA-1881 10/5/2011 16-ii CHAPTER 16. ENVIRONMENTAL ASSESSMENT TABLE OF CONTENTS 16.1 INTRODUCTION ............................................................................................................ 16-1 16.2 AIR EMISSIONS ANALYSIS ......................................................................................... 16-1 16.2.1 Air Emissions Descriptions................................................................................ 16-1 16.2.2 Air Quality Regulation ....................................................................................... 16-4

365

Direct Modeling of Envelope Dynamics in Resonant Inverters Yan Yin, Regan Zane, Robert Erickson  

E-Print Network (OSTI)

Colorado Power Electronics Center University of Colorado at Boulder Boulder, CO 80309-0425 Abstract input into its fundamental component plus two dominant sidebands. The system response is then found of applications including electronic ballasts for discharge lamps, induction heating, and medical devices. The dc

366

Lighting Research Group: Facilities: Power Analyzer  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Analyzer Power Analyzer Power Analyzer power analyzer Gonio-photometer | Integrating sphere | Power analyzer | Spectro-radiometer A power analyzer is a very necessary tool for lighting research. With the power analyzer we are able to monitor the input voltage to the lamp as well as the input power and current. The amount of power a lamp or a lamp-ballast combination uses is very important when determining its efficiency. It is also important to monitor the input voltage to make sure it doesn't vary. This can affect the light output of a lamp greatly. With the power analyzer we can also measure things like the power factor, harmonic distortion, and current crest factor of some lamps. These measurements tell us how well a lamp is working. For example, a high power

367

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

High Intensity Discharge Lamps Test Procedures High Intensity Discharge Lamps Test Procedures Sign up for e-mail updates on regulations for this and other products High-intensity discharge (HID) lamps include mercury vapor (MV), metal halide (MH), and high-pressure sodium (HPS) lamps. The Department of Energy (DOE) is establishing test procedures for HID lamps. This rulemaking is mandated by the Energy Policy and Conservation Act (EPCA). ( 42 U.S.C. 6291-6309) This Rulemaking is related to the High-Intensity Discharge Lamps Standard and Test Procedure. Recent Updates | Public Meeting Information | Submitting Public Comments | Milestones and Documents | Related Rulemakings | Statutory Authority | Contact Information Recent Updates DOE published a notice of proposed rulemaking regarding test procedures for HID lamps. 76 FR 77914 (Dec. 15, 2011).

368

Lighting in Residential and Commercial Buildings (1993 and 1995 Data)  

U.S. Energy Information Administration (EIA) Indexed Site

Types > 1995 CBECS Lighting Equipment Types > 1995 CBECS Lighting Equipment 1995 CBECS Lighting Equipment Profile Lighting Equipment - Type and Characteristics of Equipment Emits Found In Incandescent Incandescent Light Bulb Produces light by electrically heating a tungsten filament Includes energy-efficient incandescent bulbs, such as Reflector or R-Lamps (accent and task lighting), Parabolic Aluminized Reflector (PAR) lamps (flood and spot lighting), and Ellipsoidal Reflector (ER) lamps (recessed lighting) Highly inefficient because much of the energy is lost as heat 14-18 Lumens Per Watt (LPW) 14% of Lit Commercial Floorspace Standard Fluorescent Lighting with Magnetic Ballast Standard Fluorescent with Magnetic Ballast Produces light by passing electricity through mercury vapor, causing the fluorescent coating to glow or fluoresce

369

Data:4f40c9b0-a55d-4b99-a70f-0d8f26162625 | Open Energy Information  

Open Energy Info (EERE)

b0-a55d-4b99-a70f-0d8f26162625 b0-a55d-4b99-a70f-0d8f26162625 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 400W HPS with Directional Flood Lamp Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation

370

PNM - Commercial Energy Efficiency Rebate Program | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PNM - Commercial Energy Efficiency Rebate Program PNM - Commercial Energy Efficiency Rebate Program PNM - Commercial Energy Efficiency Rebate Program < Back Eligibility Commercial Savings Category Heating & Cooling Commercial Heating & Cooling Cooling Home Weatherization Construction Commercial Weatherization Design & Remodeling Other Heat Pumps Appliances & Electronics Commercial Lighting Lighting Windows, Doors, & Skylights Maximum Rebate 100% of incremental measure costs or 50% of total project costs Program Info State New Mexico Program Type Utility Rebate Program Rebate Amount '''Interior Lighting''' Screw-In CFLs: $1 - $2 Hardwired CFLs: $5 - $40 Lamp Removal: $3 - $10 T5/T8/T12 Lamps and Electronic Ballast: $0.50 - $4 High Bay T5/T8 Fixtures and Electronic Ballast: $0.30/watt reduction LED Interior Lamps/Fixtures: $12 - $20

371

Data:E8c109ea-8737-4450-b26c-bac98d3526b4 | Open Energy Information  

Open Energy Info (EERE)

c109ea-8737-4450-b26c-bac98d3526b4 c109ea-8737-4450-b26c-bac98d3526b4 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 400W MH with Directional Flood Lamp Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation

372

Data:917db384-2756-452f-a6e4-59e357edca2f | Open Energy Information  

Open Energy Info (EERE)

db384-2756-452f-a6e4-59e357edca2f db384-2756-452f-a6e4-59e357edca2f No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 1000W MH with Directional Flood Lamp Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation

373

Data:Caa7989e-c46d-47df-bbe3-f8d281e6002f | Open Energy Information  

Open Energy Info (EERE)

989e-c46d-47df-bbe3-f8d281e6002f 989e-c46d-47df-bbe3-f8d281e6002f No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 400W MH with Directional Flood Lamp Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation

374

Data:531a054f-37eb-4925-83e8-c40a3bb3ab32 | Open Energy Information  

Open Energy Info (EERE)

54f-37eb-4925-83e8-c40a3bb3ab32 54f-37eb-4925-83e8-c40a3bb3ab32 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 250W MH with Directional Flood Lamp Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation

375

Elkhorn Rural Public Pwr Dist | Open Energy Information  

Open Energy Info (EERE)

Rural Public Pwr Dist Rural Public Pwr Dist Jump to: navigation, search Name Elkhorn Rural Public Pwr Dist Place Nebraska Utility Id 5780 Utility Location Yes Ownership P NERC Location SPP NERC SPP Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Mercury Vapor Lamp 175 Watt Lighting Mercury Vapor Lamp 250 Watt Lighting Mercury Vapor Lamp 400 Watt Lighting Metal Halide 1000 Watt Lighting Metal Halide 1500 Watt Lighting Metal Halide 400 Watt Lighting RATE 1,3- Farm Residential, Commercial, Cabins, Seasonal--Single Phase Commercial RATE 12, 69- Urban Commercial Electric Space Heating, Single Phase

376

Simkar Corporation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Corporation Corporation (metal halide lamp fixtures) BEFORE THE U.S. DEPARTMENT OF ENERGY Washington, D.C. 20585 ) ) ) ) ) Case Number: 20 12-SE-5408 Issued: December 5, 2012 NOTICE OF NONCOMPLIANCE DETERMINATION Metal halide lamp fixtures are covered products subject to federal energy conservation standards as described in 42 U.S.C. §§ 6292(a)(l9), 6295(hh) and 10 C.F.R. § 431.326. Manufacturers and private 1abelers are prohibited from distributing covered products or equipment that do not comply with the applicable conservation standards. 10 C.F.R. § 429.102(a)(6); 42 U.S. C. § 6302(a)(5). Simkar Corporation ("Simkar") notified the U.S. Department of Energy ("DOE") that Simkar had manufactured 1 and distributed in commerce the following metal halide lamp fixtures ("the

377

Feature scaling of large, ballasted, field emission arrays  

E-Print Network (OSTI)

Field emitters are an exciting technology for high-frequency, high-power applications because of their excellent free space electron transport, and their potential for high current density and high current, especially when ...

Guerrera, Stephen A. (Stephen Angelo)

2011-01-01T23:59:59.000Z

378

Environmental and health aspects of lighting: Mercury  

SciTech Connect

Most discharge lamps, including fluorescent lamps, metal halide lamps, and high pressure sodium lamps, contain Mercury, a toxic chemical. Lighting professionals need to be able to respond to questions about the direct hazards of Mercury from accidentally breaking lamps, and the potential environmental hazards of lamp operation and disposal. We calculated the exposures that could occur from an accidental breakage of lamps. Acute poisoning appears almost impossible. Under some circumstances a sealed environment, such as a space station, could be contaminated enough to make it unhealthy for long-term occupation. Mercury becomes a potential environmental hazard after it becomes methylated. Mercury is methylated in aquatic environments, where it may accumulate in fish, eventually rendering them toxic to people and other animals. Lighting causes Mercury to enter the environment directly from lamp disposal, and indirectly from power plant emissions. The environmental tradeoffs between incandescent and discharge lamps depend upon the amounts released by these two sources, their local concentrations, and their probabilities of being methylated. Indirect environmental effects of lighting also include the release of other heavy metals (Cadmium, Lead and Arsenic), and other air pollutants and carbon dioxide that are emitted by fossil fuel power plants. For a given light output, the level of power plant emissions depends upon the efficacy of the light source, and is thus much larger for incandescent lamps than for fluorescent or discharge lamps. As disposal and control technologies change the relative direct and indirect emissions from discharge and incandescent lamps will change.

Clear, R.; Berman, S.

1993-07-01T23:59:59.000Z

379

Das Prfzentrum Carsten Lampe, Daniel Eggert,  

E-Print Network (OSTI)

Kalibrierlaboratorien" · Qualitätswesen analog den Anforderungen der ISO 9001 z.B. Sensorkalibriersystem / Dokumentation Prüfinstitut (durch DGWK, heute DIN CERTCO) · Seit 2003 ISO/IEC 17025 akkreditiert · Seit 2003 Prüfungen und;4 Was verlangt die Akkreditierung? ISO IEC 17025 ,,Allgemeine Anforderungen an die Kompetenz von Prüf- und

380

Max Tech and Beyond: Fluorescent Lamps  

E-Print Network (OSTI)

contain one or more rare earth elements in their chemicalcomposition. The rare earth elements are a collection of

Scholand, Michael

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Covered Product Category: Compact Fluorescent Lamps | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

per watt performance. Buyer Tips CFLs installed in enclosed fixtures designed for incandescent bulbs may overheat. This can significantly reduce both light output and lifetime....

382

Fluorescent Lighting | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fluorescent Lighting Fluorescent Lighting Fluorescent Lighting October 17, 2013 - 5:44pm Addthis Fluorescent Lighting Fluorescent Lighting Fluorescent lamps use 25%-35% of the energy used by incandescent products to provide a similar amount of light. They also last about 10 times longer (7,000-24,000 hours). The two general types of fluorescent lamps are: Compact fluorescent lamps (CFLs) -- commonly found with integral ballasts and screw bases, these are popular lamps often used in household fixtures Fluorescent tube and circline lamps -- typically used for task lighting such as garages and under cabinet fixtures, and for lighting large areas in commercial buildings. CFLs CFLs combine the energy efficiency of fluorescent lighting with the convenience and popularity of incandescent fixtures. CFLs fit most fixtures

383

EA-0819: Final Environmental Assessment | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

819: Final Environmental Assessment 819: Final Environmental Assessment EA-0819: Final Environmental Assessment Proposed Energy Conservation Standards for Eight Types of Consumer Products: Room Air Conditioners, Water Heaters, Direct Heating Equipment, Mobile Home Furnaces, Ranges and Ovens, Pool Heaters, Fluorescent Ballasts, and Television Sets This Environmental Assessment (EA) on the candidate energy conservation standards for eight appliances (room air conditioners, water heaters, direct heating equipment, mobile home furnaces, kitchen ranges and ovens, pool heaters, fluorescent lamp ballasts, and television sets) was prepared pursuant to the National Environmental Policy Act of 1969 (NEPA), regulations of the Council on Environmental Quality, Title 40, Code of Federal Regulations, Parts 1500 through 1508. The candidate conservation

384

Appliances and Commercial Equipment Standards  

NLE Websites -- All DOE Office Websites (Extended Search)

High-Intensity Discharge Lamps Energy Conservation Standard High-Intensity Discharge Lamps Energy Conservation Standard Sign up for e-mail updates on regulations for this and other products High-intensity discharge (HID) lamps include mercury vapor (MV), metal halide (MH), and high-pressure sodium (HPS) lamps. The Department of Energy (DOE) is considering establishing energy conservation standards for certain HID lamps. This rulemaking is mandated by the Energy Policy and Conservation Act (EPCA). (42 USC 6311-6317) Recent Updates | Public Meeting Information | Submitting Public Comments | Milestones and Documents | Related Rulemakings | Statutory Authority | Contact Information Recent Updates DOE published a notice of public meeting and availability of interim technical support document regarding energy conservation standards for high-intensity discharge lamps. 78 FR 13566 (February 28, 2013).

385

References : Appendices : From the Lab to the Marketplace-Ten Years Later  

NLE Websites -- All DOE Office Websites (Extended Search)

References References From the Lab to the Marketplace Ten Years Later, Energy Efficient Technologies from Research at the Lawrence Berkeley National Laboratory Berkeley Lab logo (left) with six rows of gray dots transitioning to a line art drawing of a cityscape and residential houses. References General Lawrence Berkeley National Laboratory. From the Lab to the Marketplace: Making America's Buildings More Energy-Efficient. PUB-758, Revised March 1995. National Research Council. Energy Research at DOE: Was It Worth It? National Academy Press, Washington D.C., 2001. Lighting Ballasts Verderber, R.R. Electronic High Frequency Fluorescent Ballasts (Past, Present and Future). Energy Cost Avoidance in Education Buildings Conference, LBL-28792, 1990. Verderber, R.R. Fluorescent Lamp Fixtures and Ballasts. EPRI Lighting and

386

 

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

B2.5 Safety and environmental improvements of a facility, replacement/upgrade of facility components B2.5 Safety and environmental improvements of a facility, replacement/upgrade of facility components This project focuses on the District 3 County facilities. The retrofit is to occur to the district office and the district maintenance building. In the office, the retrofit will increase the energy efficiency substantially. The project will remove: 4x 4' 4 light wrap around fixtures with magnetic style ballast, 1x drum fixture, R3o bulb, and an outside lamp. The existing wrap around fixtures will be replaced with 4x 4' 2 light T/8 Fixtures with electronic ballasts. The drum fixture will be replaced with 1x 4' 2 light T/8 fixture with electronic ballast. The R30 bulb will be replaced with a R30 compact florescent bulb along with the outside fixture. The cost of this retrofit is 1,000.00

387

Roseville Electric - Commercial Energy Efficiency Rebate Program |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Commercial Energy Efficiency Rebate Program Commercial Energy Efficiency Rebate Program Roseville Electric - Commercial Energy Efficiency Rebate Program < Back Eligibility Commercial Savings Category Heating & Cooling Commercial Heating & Cooling Cooling Other Appliances & Electronics Commercial Lighting Lighting Home Weatherization Insulation Design & Remodeling Windows, Doors, & Skylights Program Info Expiration Date 6/30/2013 State California Program Type Utility Rebate Program Rebate Amount Unitary AC/Heat Pump: $120/ton or $500/ton Package Terminal AC/Heat Pumps: $125/unit Variable Frequency Drive: $120/hp Variable Speed Motor: $75/hp Window Film: $4/sq ft Shade Tree: $30/tree Desktop Computer Network Controller: $10/computer Cold Cathode Lamps: $4/lamp Ceramic Metal Halide: $20/lamp

388

Puget Sound Energy - Commercial Energy Efficient Equipment Rebate Programs  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Puget Sound Energy - Commercial Energy Efficient Equipment Rebate Puget Sound Energy - Commercial Energy Efficient Equipment Rebate Programs Puget Sound Energy - Commercial Energy Efficient Equipment Rebate Programs < Back Eligibility Commercial Industrial Institutional Nonprofit Schools Savings Category Heating & Cooling Commercial Heating & Cooling Cooling Appliances & Electronics Heat Pumps Commercial Lighting Lighting Manufacturing Program Info State District of Columbia Program Type Utility Rebate Program Rebate Amount '''Lighting''' Small Business Lighting: $3 - $190 CFLs: $3 - $12 LEDs: $10 - $25 Ceramic Metal Halide Lamps: $25 LED Exit Signs: $50 LED Traffic Signals: $5 - $20 Lighting Controls: $40 - $80 T8 Lamp Upgrade: $1 per lamp '''HVAC''' HVAC Installations (New Construction): $30/ton HVAC Replacements: $100 - $550

389

Literature Review of the Effects of UV Exposure on PV Modules  

Energy.gov (U.S. Department of Energy (DOE))

This PowerPoint presentation, originally presented at the NREL 2013 PV Module Reliability Workshop on Feb. 26-27, 2013 in Denver, CO, presents the literature review of the effects of prolonged UV exposure of PV modules, with a particular emphasis on UV exposure testing using artificial light sources, including fluorescent, Xenon, and metal halide lamps.

390

Data:B36554fe-57f4-444f-953e-5d09160ec277 | Open Energy Information  

Open Energy Info (EERE)

554fe-57f4-444f-953e-5d09160ec277 554fe-57f4-444f-953e-5d09160ec277 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 175W MV Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation Source Parent: Comments

391

Data:F116d283-7936-470d-9c42-478a2c59ce1e | Open Energy Information  

Open Energy Info (EERE)

6d283-7936-470d-9c42-478a2c59ce1e 6d283-7936-470d-9c42-478a2c59ce1e No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 400W HPS Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation Source Parent: Comments

392

Data:E87c1d68-e3f8-4ba9-8f94-3e5ec50105e4 | Open Energy Information  

Open Energy Info (EERE)

7c1d68-e3f8-4ba9-8f94-3e5ec50105e4 7c1d68-e3f8-4ba9-8f94-3e5ec50105e4 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 400W MH Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation Source Parent: Comments

393

Data:E5fba98a-2fd6-4744-9482-76cfb2c2f53b | Open Energy Information  

Open Energy Info (EERE)

fba98a-2fd6-4744-9482-76cfb2c2f53b fba98a-2fd6-4744-9482-76cfb2c2f53b No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 250W HPS Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation Source Parent: Comments

394

Data:Dfbb2c41-7784-4206-8f7b-787a493d01dc | Open Energy Information  

Open Energy Info (EERE)

Dfbb2c41-7784-4206-8f7b-787a493d01dc Dfbb2c41-7784-4206-8f7b-787a493d01dc No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 100W HPS Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation Source Parent: Comments

395

BEFORE THE U.S. DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Philips Lighting Electronics N. A. Philips Lighting Electronics N. A. (fluorescent lamp ballasts) ) ) ) ) ) Case Number: 2012-SE-2605 NOTICE OF PROPOSED CIVIL PENALTY Date issued: November 29,2012 Number of alleged violations: 7,498 Maximum possible assessment: $1,499,600 Proposed civil penalty: $1,499,600 The U.S. Department of Energy ("DOE") Office of the General Counsel, Office of Enforcement, alleges that Philips Lighting Electronics N. A. ("Philips") has violated certain provisions of the Energy Policy and Conservation Act, 42 U.S.C. § 6291 et seq. ("the Act"), and 10 C.F.R. Parts 429 and430. Specifically, DOE alleges: 1. A fluorescent lamp ballast is a "covered product" as defined in 42 U.S.C. § 6292(a)(l3) and 10 C.F.R. § 430.2;

396

Data:C7739e7e-b748-4e8d-b00a-0c619ad25436 | Open Energy Information  

Open Energy Info (EERE)

9e7e-b748-4e8d-b00a-0c619ad25436 9e7e-b748-4e8d-b00a-0c619ad25436 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 150W HPS Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation Source Parent: Comments

397

Data:653f8e21-b66d-4dee-985b-d4e1da31742d | Open Energy Information  

Open Energy Info (EERE)

f8e21-b66d-4dee-985b-d4e1da31742d f8e21-b66d-4dee-985b-d4e1da31742d No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 250W MH Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation Source Parent: Comments

398

BEFORE THE U.S. DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Keystone Technologies, LLC Keystone Technologies, LLC (fluorescent lamp ballasts) ) ) ) ) ) Case Number: 2013-CE-2601 NOTICE OF PROPOSED CIVIL PENALTY Date issued: February 7, 2013 Number of alleged violations: 2,555 (7 models; 365 days) Maximum possible assessment: $511,000 Proposed civil penalty: $51,100 The U.S. Department of Energy ("DOE") Office of the General Counsel, Office of Enforcement, alleges that Keystone Technologies, LLC ("Keystone") has violated certain provisions of the Energy Policy and Conservation Act, 42 U.S.C. § 6291 et seq. ("the Act"), and 10 C.F.R. § 429.12. Specifically, DOE alleges: 1. Keystone has manufactured 1 a variety of fluorescent lamp ballasts, including models KTEB-275-UV-TP-PIC, KTEB-275-1-TP-PIC-SL, KTEB-240-UV-TP-PIC,

399

Microsoft Word - FOR WEB - Universal 26004 NPCP based on GE traffic 4901.docx  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Universal Lighting Technologies, Inc. Universal Lighting Technologies, Inc. (fluorescent lamp ballasts) ) ) ) ) ) Case Number: 2013-SE-26004 NOTICE OF PROPOSED CIVIL PENALTY Date issued: August 19, 2013 Number of alleged violations: 454 Maximum possible assessment: $90,800 Proposed civil penalty: $90,800 The U.S. Department of Energy ("DOE") Office of the General Counsel, Office of Enforcement, alleges that Universal Lighting Technologies, Inc. ("Universal") has violated certain provisions of the Energy Policy and Conservation Act, 42 U.S.C. § 6291 et seq. ("the Act"), and 10 C.F.R. Parts 429 and 430. Specifically, DOE alleges: 1. A fluorescent lamp ballast is a "covered product" under 42 U.S.C §§ 6291(29)(A) and 6292(a)(13);

400

Data:A69444d6-0ec2-458a-816f-7076f7caacaf | Open Energy Information  

Open Energy Info (EERE)

0ec2-458a-816f-7076f7caacaf 0ec2-458a-816f-7076f7caacaf No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Excelsior Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: Outdoor Lighting Service- 175W MH Sector: Lighting Description: Applicable only to outdoor lighting by means of ballast operated lamp fixtures that do not require a dedicated transformer and street lighting service by means of ballast operated lamp fixtures, subject to the established rules and regulations of the Cooperative. Source or reference: ISU Documentation Source Parent: Comments Applicability

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Compact light source performance in recessed type luminaires  

SciTech Connect

Photometric comparisons were made with an indoor, recessed, type luminaire using incandescent, high intensity discharge and compact fluorescent lamps. The test results show substantial performance advantages, as expected, for the discharge light sources where the efficacy gains can be in the order for 400% even when including the ballast losses associated with the discharge lamps. The candlepower distribution patterns emerging from these luminaries are also different from those associated with the baseline incandescent lamps, and which are in some ways, even more desirable from a uniformity of illuminance perspective. A section on fluorescent lamp starting is also included which describes a system having excellent starting characteristics in terms of electrode starting temperature (RH/RC technique), proper operating frequency to minimize unwanted IR interactions, and satisfactory current crest factor values to help insure life performance.

Hammer, E.E.

1998-11-01T23:59:59.000Z

402

Hybrid Lead Halide Iodide and Lead Halide Bromide in Efficient Hole Conductor Free Perovskite Solar Cell  

Science Journals Connector (OSTI)

One of the important properties of the organicinorganic perovskite for their use in photovolatic cells is the possibility to tune their optical properties (e.g., band gap). ...

Sigalit Aharon; Bat El Cohen; Lioz Etgar

2014-04-17T23:59:59.000Z

403

Spectroscopic effects of disorder and vibrational localization in mixed-halide metal-halide chain solids  

SciTech Connect

Resonance Raman techniques, together with lattice-dynamics and Peierls-Hubbard modelling, are used to explore the electronic and vibrational dynamics of the quasi-one-dimensional metal-halogen chain solids [Pt(en)[sub 2

Love, S.P.; Scott, B.; Worl, L.A.; Huckett, S.C.; Saxena, A.; Huang, X.Z.; Bishop, A.R.; Swanson, B.I.

1993-01-01T23:59:59.000Z

404

Halide and Oxy-halide Eutectic Systems for High Performance High Temperature Heat Transfer Fluids  

Energy.gov (U.S. Department of Energy (DOE))

This presentation was delivered at the SunShot Concentrating Solar Power (CSP) Program Review 2013, held April 2325, 2013 near Phoenix, Arizona.

405

Halide and Oxy-halide Eutectic Systems for High Performance High...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

setup (building a home-made enclosure to purge with N 2 ) in case salts also react with air - Quartz weight ordered to replace Ni Measure volume expansion directly...

406

Halide and Oxy-Halide Eutectic Systems for High Performance High...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

High Performance High Temperature Heat Transfer Fluids Award Number: DE-FOA-0005942 Report Date: 15 January 2013 PI: Peiwen (Perry) Li * Numerical simulation and combined DSCTGA...

407

New Research Tool for Energy-Efficient Residential Fixtures  

NLE Websites -- All DOE Office Websites (Extended Search)

4 4 New Research Tool for Energy-Efficient Residential Fixtures Lighting Group researcher Erik Page stands next to the new goniophotometer, shown in a multiple-exposure photo that represents a complete sensor sweep around a table lamp. The lamp is seen reflected in a mirror mounted on a swing arm, aimed at a photocell used for data acquisition. The residential lighting sector represents a significant opportunity for energy conservation because it currently uses inefficient incandescent sources almost exclusively. Compact fluorescent lamps (CFLs) have the potential to transform this market by using one-fourth as much power as an incandescent to provide the same amount of light. While technical advances such as triphosphors and electronic ballasts have addressed issues of color

408

Florida Public Utilities - Commercial Energy Efficiency Rebate Programs |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Public Utilities - Commercial Energy Efficiency Rebate Public Utilities - Commercial Energy Efficiency Rebate Programs Florida Public Utilities - Commercial Energy Efficiency Rebate Programs < Back Eligibility Commercial Savings Category Heating & Cooling Commercial Heating & Cooling Cooling Heat Pumps Appliances & Electronics Commercial Lighting Lighting Home Weatherization Windows, Doors, & Skylights Maximum Rebate Lamp Only Lighting Upgrade: $100 Window Film: $100 Program Info State Florida Program Type Utility Rebate Program Rebate Amount Ballast and Lamp Lighting Upgrade: $0.10/watt saved Lamp Only Lighting Upgrade: $0.025/watt saved AC/Heat Pump: $100 Window Film: $0.50/sq. ft. Chiller: Up to $100/kW Provider Florida Public Utilities Florida Public Utilities offers the Energy for Life Conservation program to

409

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

691 - 4700 of 31,917 results. 691 - 4700 of 31,917 results. Download PQL: Order (2013-CE-27001) DOE ordered P.Q.L., Inc. to pay a $8,000 civil penalty after finding PQL had failed to certify that various basic models of medium base compact fluorescent lamps, general service fluorescent lamps, fluorescent lamp ballasts, and illuminated exit signs comply with the applicable energy conservation standards. http://energy.gov/gc/downloads/pql-order-2013-ce-27001 Download Information Request http://energy.gov/management/downloads/information-request Download EA-1170: Final Environmental Assessment Area 5 Radioactive Waste Management Site Access Improvement at the Nevada Test Site http://energy.gov/nepa/downloads/ea-1170-final-environmental-assessment Download Nuclear Energy Research and Development Roadmap

410

Data:7ef07281-4772-4a95-8965-e7e0a2d50bdf | Open Energy Information  

Open Energy Info (EERE)

1-4772-4a95-8965-e7e0a2d50bdf 1-4772-4a95-8965-e7e0a2d50bdf No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Auburn Board of Public Works Effective date: 2012/01/01 End date if known: Rate name: Outdoor Lighting Service Sector: Lighting Description: This is available to residential, commercial and industrial customers. These lights cannot be used on pubic or semi-public areas. Available at locations where private lighting/ security lights are installed and electrical usage is un-metered The rate per lamp per month for each lighting unit will be computed as: Lamps rated cpacity per lamp including Ballast X $0.097

411

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

91 - 1700 of 26,777 results. 91 - 1700 of 26,777 results. Download Report to the President on Capturing Domestic Competitive Advantage in Advanced Manufacturing Report to the President on Capturing Domestic Competitive Advantage in Advanced Manufacturing http://energy.gov/eere/downloads/report-president-capturing-domestic-competitive-advantage-advanced-manufacturing Download PQL: Order (2013-CE-27001) DOE ordered P.Q.L., Inc. to pay a $8,000 civil penalty after finding PQL had failed to certify that various basic models of medium base compact fluorescent lamps, general service fluorescent lamps, fluorescent lamp ballasts, and illuminated exit signs comply with the applicable energy conservation standards. http://energy.gov/gc/downloads/pql-order-2013-ce-27001 Download EIS-0321: Draft Environmental Impact Statement

412

Richland Energy Services - Energy Efficient Commercial Lighting Program |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Richland Energy Services - Energy Efficient Commercial Lighting Richland Energy Services - Energy Efficient Commercial Lighting Program Richland Energy Services - Energy Efficient Commercial Lighting Program < Back Eligibility Agricultural Commercial Industrial Institutional Nonprofit Savings Category Other Appliances & Electronics Commercial Lighting Lighting Maximum Rebate 70% of the total cost Program Info Expiration Date 9/30/2012 State District of Columbia Program Type Utility Rebate Program Rebate Amount T5/T8 with Electric Ballasts: $10 - $65 Hardwired CFL's: $40 - $80 Screw In CFL's: $3 - $12 Cold Cathode: $3 - $15 Ceramic Metal Halide Fixture: $30 - $50 LED's: $15 - $50 Induction: $80 - $400 High-output T5/T8: $50 - $180 Metal Halide/High Pressure Sodium: $80 - $400 Stairwell/Garage Fluorescent Fixture: $50 Occupancy Sensor/Timer: $30 - $60

413

NOPM and Availability of Framework Document for HID Lamps  

NLE Websites -- All DOE Office Websites (Extended Search)

8:48 Feb 27, 2012 8:48 Feb 27, 2012 Jkt 226001 PO 00000 Frm 00008 Fmt 4702 Sfmt 4702 E:\FR\FM\28FEP1.SGM 28FEP1 mstockstill on DSK4VPTVN1PROD with PROPOSALS Federal Register / Vol. 77, No. 39 / Tuesday, February 28, 2012 / Proposed Rules 11785 collections for particular program, except where required by statute. III. Questions for Comment The list below includes the questions about these reform ideas that address issues which are of greatest interest to OMB at this stage of the process. Comments addressing any other concerns, and other types of feedback, are also welcome. In addition, as was explained at the beginning of this notice, the public comments received by OMB will be posted on OMB's Web site and at http:// www.regulations.gov. Accordingly, please do not include in your comments

414

Conservation Potential of Compact Fluorescent Lamps in India and Brazil  

E-Print Network (OSTI)

1988. The private sector in Brazil owned (in 1986) 40% ofElectricity Conservation in Brazil: Potential and Pro-electricity consumption in Brazil's residential sector was

Gadgil, A.J.

2008-01-01T23:59:59.000Z

415

Ancient Lamps, Earrings Yield Their Secrets Under Neutron Imaging...  

NLE Websites -- All DOE Office Websites (Extended Search)

a colonial-period plantation in Rhode Island. The samples include artifacts from daily life: a clothing buckle, a knife, and some building hardware. One circular object from...

416

Conservation Potential of Compact Fluorescent Lamps in India and Brazil  

E-Print Network (OSTI)

also additional benefits from avoided costs of environmentalpremium for India)) - (avoided annual cost of incandescents)electricity) + (avoided annual cost of incandescents) - (

Gadgil, A.J.

2008-01-01T23:59:59.000Z

417

Max Tech and Beyond: High-Intensity Discharge Lamps  

E-Print Network (OSTI)

demonstration (like street lights) and commercialization andthe dominant light source for street and roadway lighting,has been a popular light source for street lighting because

Scholand, Michael

2012-01-01T23:59:59.000Z

418

LED Performance Specification Series: T8 Replacement Lamps  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

program of SSL research, development, and commercialization. For Program Information: Kelly Gordon Pacific Northwest National Laboratory Phone: (503) 417-7558 E-mail:...

419

Photo-Polarography with a Flash-Lamp  

Science Journals Connector (OSTI)

... PHOTO-POLAROGRAPHY, originating from the synthesis of ... -POLAROGRAPHY, originating from the synthesis of photo-chemistry and polarography, records photokinetic-currents caused by ...

H. BERG; H. SCHWEISS

1961-09-23T23:59:59.000Z

420

Conservation Potential of Compact Fluorescent Lamps in India and Brazil  

E-Print Network (OSTI)

1.7% of in- stalled hydroelectric capacity. Op. cit. ref [in Ig86) based on hydroelectric generation, and most of thethe still abundant hydroelectric potential of the country.

Gadgil, A.J.

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Apparatus to facilitate lengthening the life of incandescent lamps  

SciTech Connect

An energizing circuit is described for an incandescent bulb comprising a transformer having a primary winding connectable to an AC mains source and first and second secondary windings for producing first and second voltages. The first secondary winding is connected to an input of a first full-wave rectifier means and the second secondary winding is connected to an input of a second full-wave rectifier means, the full-wave rectifier means having outputs connected in parallel across the bulb. The first voltage is sufficient to fully illuminate the bulb and the second voltage is sufficient to maintain the bulb warm but with little or no light output, a first switch being connected between the first secondary winding and the first rectifier means whereby, when the first switch is open, the bulb is energized solely by the second voltage.

Spissinger, F.H.

1987-03-17T23:59:59.000Z

422

Series Resonant Inverter with Contactless Transformers for Multiple LED Lamps.  

E-Print Network (OSTI)

??A half-bridge series-resonant inverter adopted to realize the quasi current source and the constant current source with a number of contactless transformers in series for (more)

Cheng, Shuen-Wen

2013-01-01T23:59:59.000Z

423

All General Counsel Reports | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

December 9, 2012 December 9, 2012 Teddico: Order (2012-SE-5409) DOE ordered The Electrical Design, Development and Implementation Company d/b/a Teddico to pay a $18,994 civil penalty after finding Teddico had manufactured and distributed in commerce in the U.S. 218 units of a variety of noncompliant metal halide lamp fixtures basic models. December 7, 2012 Advance Patent Waiver W(A)2011-065 This is a request by OWENS CORNING for a DOE waiver of domestic and foreign patent rights under agreement DE-EE0005338. December 5, 2012 Simkar: Noncompliance Determination (2012-SE-5408) DOE issued a Notice of Noncompliance Determination to Simkar Corporation finding that magnetic probe-start and pulse-start basic models of metal halide lamp fixtures do not comport with the energy conservation standards.

424

BEFORE THE U.S. DEPARTMENT OF ENERGY  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Issued: November 20, 2012 Issued: November 20, 2012 Case Number: 2012-SE-5409 NOTICE OF NONCOMPLIANCE DETERMINATION Metal halide lamp fixtures are covered products subject to federal energy conservation standards as described in 42 U.S.C. §§ 6292(a)(19), 6295(hh) and 10 C.P.R.§ 431.326. Manufacturers and private labelers are prohibited from distributing covered products or equipment that do not comply with the applicable conservation standards. 10 C.P.R.§ 429.102(a)(6); 42 U.S.C. § 6302(a)(5). The Electrical Design, Development and Implementation Company d/b/a Teddico ("Teddico") notified the U.S. Department of Energy ("DOE") that Teddico had manufactured' and distributed in commerce the following magnetic probe-statt metal halide lamp fixtures ("the Teddico Basic

425

ENVIRONMENTAL ASSESSMENT FOR PROPOSED ENERGY CONSERVATION STANDARDS FOR EIGHT TYPES OF CONSUMER  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ENVIRONMENTAL ASSESSMENT FOR PROPOSED ENERGY ENVIRONMENTAL ASSESSMENT FOR PROPOSED ENERGY CONSERVATION STANDARDS FOR EIGHT TYPES OF CONSUMER PRODUCTS: ROOM AIR CONDITIONERS, WATER HEATERS, DIRECT HEATING EQUI?MENT, MOBILE HOME FURNACES, RANGES AND OVENS, POOL HEATERS, FLUORESCENT BALLASTS, AND TELEVISIONS INTRODUCTION AND NEED FOR PROPOSEI) ACTION This Environmental Assessment (EA) on the candidate energy conservation standards for eight appliances (room air conditioners, water heaters, direct heating equipment, mobile home furnaces, kitchen ranges and ovens, pool heaters, fluorescent lamp ballasts, and television sets) was prepared pursuant to the National Environmental Policy Act of 1969 (NEPA), regulations of the Council on Environmental Quality, Title 40, Code of Federal Regulations, Parts 1500 through 1508. The candidate conservation standards are being

426

Cornell University Electric Lighting Report  

NLE Websites -- All DOE Office Websites (Extended Search)

Electric Lighting Quality Electric Lighting Quality The CUSD lighting design team utilized energy efficient products that meshed well with our daylighting scheme. We chose to use fluorescent tubes or compact fluorescent bulbs with an energy consumption of between 15 and 30 Watts throughout the house. The ballasts for all lamps dim to a 1% light output, so the interior and exterior lights can be adjusted as the level of available daylight fluctuates. Light sensors have been placed in front of our two largest apertures, allowing us to control how much artificial light is supplied to each space. The control of our ballasts is intricate, but refined and tested to avoid dysfunctional dimming or switching. While automatic controls are included, manual user overrides are provided in case the occupant prefers

427

Development of a Web-based Emissions Reduction Calculator for Street Light and Traffic Light Retrofits  

E-Print Network (OSTI)

DEVELOPMENT OF A WEB-BASED, EMISSIONS REDUCTION CALCULATOR FOR STREET LIGHT AND TRAFFIC LIGHT RETROFITS Zi Liu, Ph.D. Research Engineer Jeff S. Haberl, Ph.D., P.E. Professor/Assc. Director Don Gilman, P..., street lights and traffic lights represent one of the largest categories of electricity used by a city. By retrofitting the street lights with energy efficient lamps such as high pressure sodium and metal halide and traffic lights with light...

Liu, Z.; Gilman, D.; Haberl, J. S.; Culp, C.

2005-01-01T23:59:59.000Z

428

Explosive composition with group VIII metal nitroso halide getter  

DOE Patents (OSTI)

An improved explosive composition is disclosed and comprises a major portion of an explosive having a detonation velocity between about 1,500 and 10,000 meters per second and a minor amount of a getter additive comprising a non-explosive compound or mixture of non-explosive compounds capable of chemically reacting with free radicals or ions under shock initiation conditions of 2,000 calories/cm.sup.2 or less of energy fluence.

Walker, Franklin E. (18 Shadow Oak Rd., Danville, CA 94526); Wasley, Richard J. (4290 Colgate Way, Livermore, CA 94550)

1982-01-01T23:59:59.000Z

429

Explosive composition with group VIII metal nitroso halide getter  

DOE Patents (OSTI)

An improved explosive composition is disclosed and comprises a major portion of an explosive having a detonation velocity between about 1,500 and 10,000 meters per second and a minor amount of a getter additive comprising a non-explosive compound or mixture of non-explosive compounds capable of chemically reacting with free radicals or ions under shock initiation conditions of 2,000 calories/cm[sup 2] or less of energy fluence.

Walker, F.E.; Wasley, R.J.

1982-06-22T23:59:59.000Z

430

Development of Synthetic Phenol from Benzene Halides1  

Science Journals Connector (OSTI)

William J. Hale , Edgar C. Britton ... Halogen-Containing Hydrocarbons from Petroleum and Natural Gas ...

William J. Hale; Edgar C. Britton

1928-01-01T23:59:59.000Z

431

Lanthanum Halide Nanoparticle Scintillators for Nuclear Radiation Detection  

SciTech Connect

Nanoparticles with sizes <10 nm were fabricated and characterized for their nanocomposite radiation detector properties. This work investigated the properties of several nanostructured radiation scintillators, in order to determine the viability of using scintillators employing nanostructured lanthanum tribromide, lanthanum trifluoride, or cerium tribromide. Preliminary results of this investigation are consistent with the idea that these materials have an intrinsic response to nuclear radiation that may be correlated to the energy of the incident radiation.

Guss, P. P., Guise, R., Yuan, D., Mukhopadhyay, S., O'Brien, R., Lowe, D.

2013-02-01T23:59:59.000Z

432

Bright Light-Emitting Diodes based on Organometal Halide Perovskite  

E-Print Network (OSTI)

this class of materials to be excellent semiconductors for optoelectronic devices.1-7 Their primary advantages lie in the fact that they can be easily solution processed, require no high temperature heating, and they possess an optical bandgap which...

Tan, Zhi-Kuang; Moghaddam, Reza Saberi; Lai, May Ling; Docampo, Pablo; Higler, Ruben; Deschler, Felix; Price, Michael; Sadhanala, Aditya; Pazos, Luis M.; Credgington, Dan; Hanusch, Fabian; Bein, Thomas; Snaith, Henry J.; Friend, Richard H.

2014-08-03T23:59:59.000Z

433

Stark Effect in Color Centers of Alkali Halides  

Science Journals Connector (OSTI)

The stark effect of the F center in NaCl, NaBr, KCl, KBr, KI, and RbCl, the M center in KCl, and the Z1 center in KCl: Sr was measured using an ac electric field. The fractional change of the absorption coefficient, ???, at the peak of the F band, normalized to a Lorentz local field of 200 kV/cm, was found to be approximately 210-5 for NaCl and NaBr, 1110-5 for RbCl, and 1710-5 for KCl, KBr, and KI. The value of ??? at the peak of the M band in KCl was (3.90.4)10-5 for an applied electric field of 97 kV/cm. A measurement of the change in the absorption coefficient, ??, versus photon energy produced a nonsymmetrical curve. This indicates that the effect observed was not the linear Stark effect, and thus provides additional evidence that Seitz's model is incorrect. The absorption coefficient increased at energies lower than the M band, corresponding to a decrease in the absorption coefficient of the M band. The effect is attributed to the mixing of two nondegenerate energy levels of opposite parity. The optical transition to the level of lower energy is normally forbidden. The Z1 center in KCl: Sr did not exhibit a detectable Stark effect. It was determined, however, that ???unit.

Charles R. Rhyner and John R. Cameron

1968-05-15T23:59:59.000Z

434

Reactions of nitrogen heterocycle-organolithium intermediates with lead halides  

E-Print Network (OSTI)

, Amer. Chem. Soc. , 45 (1923) 1821. 4. L. C. Will *, ~cl 6~eh it, SpA tiNV. The Hague, Netherlands, 1964. 5. L. C. . Will, d G. J. M. 4 K k, ~ltl thFI id f~cl*d~ch It, Sht !, J Utrecht N. V. , Netherlands, 1965. 6. iM. C. Henry and B. C. Pant..., Amer. Chem. Soc. , 45 (1923) 1821. 4. L. C. Will *, ~cl 6~eh it, SpA tiNV. The Hague, Netherlands, 1964. 5. L. C. . Will, d G. J. M. 4 K k, ~ltl thFI id f~cl*d~ch It, Sht !, J Utrecht N. V. , Netherlands, 1965. 6. iM. C. Henry and B. C. Pant...

Kinney, Jerry Neal

2012-06-07T23:59:59.000Z

435

Structure and Chemistry in Halide Lead-Tellurite Glasses  

SciTech Connect

A series of TeO2-PbO glasses were fabricated with increasing fractions of mixed alkali, alkaline earth, and lanthanide chlorides. The glass and crystal structure was studied with Raman spectroscopy, nuclear magnetic resonance (NMR), X-ray diffraction, and electron microscopy. As the chloride fraction increased, the medium-range order in the glass decreased up to a critical point (~14 mass% of mixed chlorides), above which the glasses became phase-separated. Resulting phases are a TeO2/PbO-rich phase and a crystalline phase rich in alkali chlorides. The 125Te NMR indicates, contrary to previous studies, that Te site distribution did not change with increased concentrations of M+, M2+, and M3+ cations, but rather is controlled by the Te/Pb molar ratio. The 207Pb NMR shows that two Pb species exist and their relative concentration changes nearly linearly with addition of the mixed chlorides, indicating that the additives to the TeO2-PbO glass are accommodated by changing the Pb species. The 23Na and 35Cl NMR indicate that Na and Cl are distributed in the single-phase glass phase up to the critical point, and at higher concentrations partition to crystalline phases. Transmission electron microscopy shows that the sample at the critical point contains ~10 nm seed nuclei that increase in size and concentration with exposure to the electron beam.

McCloy, John S.; Riley, Brian J.; Lipton, Andrew S.; Windisch, Charles F.; Washton, Nancy M.; Olszta, Matthew J.; Rodriguez, Carmen P.

2013-02-11T23:59:59.000Z

436

The future of the carbon cycle: review, calcification response, ballast and feedback on atmospheric CO2  

Science Journals Connector (OSTI)

...inorganic carbon ( C O2) in seawater is in the form HCO- 3 , the...inorganic carbon species in seawater is such that, for a given...effective buffering capacity of seawater is analogous to the Revelle...larger capacity for carbon storage in the oceans than in the atmosphere...

2003-01-01T23:59:59.000Z

437

Buildings Energy Data Book: 5.6 Lighting  

Buildings Energy Data Book (EERE)

3 3 Shipments of Fluorescent Lamp Ballasts Standard Magnetic Type (1) Electronic Type Total Quantity Value Quantity Value Quantity Value Year (million) ($million) (million) ($million) (million) ($million) 1985 70.1 398.9 N.A N.A. 70.1 398.9 N.A. 1986 69.4 396.1 0.4 11.8 69.8 407.9 1% 1988 74.6 450.9 1.1 25.5 75.7 476.4 1% 1990 78.4 546.3 3.0 69.3 81.4 615.6 4% 1992 83.7 537.7 13.3 274.6 97.0 812.3 14% 1994 83.5 550.0 24.6 390.8 108.1 940.7 23% 1996 67.0 457.8 30.3 451.4 97.3 909.2 31% 1998 63.9 401.4 39.8 512.8 103.7 914.3 38% 2000 55.4 343.0 49.3 555.5 104.8 898.5 47% 2002 40.7 263.3 53.8 573.1 94.5 836.4 57% 2004 30.5 218.4 59.2 579.4 89.7 797.8 66% 2005 22.2 175.1 61.3 594.6 83.5 769.8 73% Note(s): Source(s): Electronic Type as a % of Total Units Shipped 1) Standard magnetic type includes uncorrected and corrected power-factor type ballasts. DOC Current Industrial Reports: Fluorescent Lamp Ballasts, MQ335C(05)-5, July 2006 for 2000-2005; DOC, Current Industrial Reports: Fluorescent Lamp

438

ESPC ENABLE: ECM Summary  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ESPC ENABLE: ECM Summary ESPC ENABLE: ECM Summary ECM Included Not Included Lighting * Lamps, Ballasts, Fixtures * Controls: Occupancy, Day lighting (on/off, dimming) * Solar Lighting (off-grid installations allowed) Water * Sanitary plumbing fixtures: sinks, toilets, urinals, showers * Irrigation * Leak repair * Domestic/commercial hot water heaters * Water based appliances: dishwasher, ice machine, clothes washer, etc. * Heating/Cooling system improvements (cooling towers, once through cooling, condensate reclaim) HVAC Controls Whole building control strategies including: * Time/Temperature Set-back * Demand/Night Ventilation * Advanced Controls 1 : Energy Management Control Systems (EMCS) / Building Automation Systems (BAS) HVAC Equipment Basic whole building/system one-for-one replacement

439

ESPC ENABLE: ECM Summary  

NLE Websites -- All DOE Office Websites (Extended Search)

ESPC ENABLE: ECM Summary ESPC ENABLE: ECM Summary ECM Included Not Included Lighting * Lamps, Ballasts, Fixtures * Controls: Occupancy, Day lighting (on/off, dimming) * Solar Lighting (off-grid installations allowed) Water * Sanitary plumbing fixtures: sinks, toilets, urinals, showers * Irrigation * Leak repair * Domestic/commercial hot water heaters * Water based appliances: dishwasher, ice machine, clothes washer, etc. * Heating/Cooling system improvements (cooling towers, once through cooling, condensate reclaim) HVAC Controls Whole building control strategies including: * Time/Temperature Set-back * Demand/Night Ventilation * Advanced Controls 1 : Energy Management Control Systems (EMCS) / Building Automation Systems (BAS) HVAC Equipment Basic whole building/system one-for-one replacement

440

U.S. Department of Energy NEPA Categorical Exclusion Determination Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Jacksonville Jacksonville Location: City Jacksonville NC American Recovery and Reinvestment Act: Proposed Action or Project Description: 1) Technical consultant to develop energy efficiency and conservation plan; 2) hire Energy Conservation Officer; 3) energy efficiency retrofits (lighting fixtures, exit signs, T-12 lamps and ballast replacements, HVAC replacements/upgrades, thermostat replacements, Energy Star hot water heaters, occupancy sensors, upgrade of propane heaters to natural gas, installation of data center cooling system, and upgrade power supplies) in City Hall, Public Services Buildings (3 buildings), Commons Recreation Building, Fire Stations 3 and 4, Kerr Street Recreation Center, Northwoods Recreation Center, and Jack Amyette Community Center; 4) purchase and install energy management system; 5) education and

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

High-Intensity Discharge Lighting Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

High-Intensity Discharge Lighting Basics High-Intensity Discharge Lighting Basics High-Intensity Discharge Lighting Basics August 15, 2013 - 5:59pm Addthis High-intensity discharge (HID) lighting provides the highest efficacy and longest service life of any lighting type. It can save 75%-90% of lighting energy when it replaces incandescent lighting. Illustration of a high-intensity discharge (HID) lIllustration amp. The lamp is a tall cylindrical shape, and a cutout of the outer tube shows the materials inside. A long, thin cylinder called the arc tube runs through the lamp between two electrodes. The space around the arc tube is labeled as a vacuum. In a high-intensity discharge lamp, electricity arcs between two electrodes, creating an intensely bright light. Mercury, sodium, or metal halide gas

442

Data:C2c3ca91-49d0-416e-8534-16d52fcadb9b | Open Energy Information  

Open Energy Info (EERE)

c3ca91-49d0-416e-8534-16d52fcadb9b c3ca91-49d0-416e-8534-16d52fcadb9b No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Village of Davenport, Nebraska (Utility Company) Effective date: 2012/11/15 End date if known: Rate name: General Service Lighting Sector: Lighting Description: To energy only for Customer-owned lighting, provided the customer installs photo-electric controlled equipment approved by the District to limit the burning time of the lighting units to the period from dusk till daylight. Price of lamp per month: ([Rated kW capacity of lamp, including ballast] x 4000 x $0.0741)/12

443

CX-005225: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

225: Categorical Exclusion Determination 225: Categorical Exclusion Determination CX-005225: Categorical Exclusion Determination Alaska-Tribe-Doyon, Limited CX(s) Applied: B2.5, B5.1 Date: 02/10/2011 Location(s): Fairbanks, Alaska Office(s): Energy Efficiency and Renewable Energy Energy Efficiency and Conservation Block Grant Program. Doyon Limited of Alaska proposes to conduct building retrofits of the Doyon Office Building located at 1 Doyon Place in Fairbanks, Alaska. Building retrofits would include redesigning and retrofitting the Doyon Plaza interior lighting system including removing/replacing various lamps, lamp housings, ballasts, and wiring. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-005225.pdf More Documents & Publications EA-1183: Finding of No Significant Impact CX-002017: Categorical Exclusion Determination

444

Incandescent Lighting Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Incandescent Lighting Basics Incandescent Lighting Basics Incandescent Lighting Basics August 16, 2013 - 10:00am Addthis Incandescent lamps operate simply by heating a metal filament inside a bulb filled with inert gas. Because they operate directly on variety of common power types including common household alternating current or direct current such as batteries or automobiles, they do not require a special power supply or ballast. They turn on up instantly, providing a warm light with excellent color rendition because the light is produced in much the same way as the light from the sun. They can also be easily dimmed using inexpensive controls and are available in a staggering variety of shapes and sizes. However, incandescent lamps have a low efficacy (10-17 lumens per watt) compared with other lighting options and a short average

445

 

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The EECBG funds would be utilized solely for the material purchases of new electrical lighting apparatus/equipment in the replacement and The EECBG funds would be utilized solely for the material purchases of new electrical lighting apparatus/equipment in the replacement and upgrades of introducing new energy-efficient lighting equipment for approximately (14) city owned facilities. The labor portion for all listed facilities will be performed by existing City staff licensed to conduct electrical service applications. Project Description : Replace existing inefficient lighting in City properties utilizing new energy efficient T-8 lighting fixtures/lamps, T-8 retrofit ballast kits for 4' & 8' fixtures, new T-5 high bay lighting fixtures/lamps, LED style exit light units & emergency light units. The project estimated cost stated below is for materials only. Labor to install these upgrades will be provided by existing properly licensed city staff.

446

Glossary | Building Energy Codes Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Balancing, Air Balancing, Air Adjusting air flow rates through air distribution system devices, such as fans and diffusers, by manually adjusting the position of dampers, splitter vanes, extractors, etc., or by using automatic control devices, such as constant air volume or variable air volume boxes. Balancing, Hydronic Adjusting water flow rates through hydronic distribution system devices, such as pumps and coils, by manually adjusting the position valves, or by using automatic control devices, such as automatic flow control valves. Ballast A device used in conjunction with an electric-discharge lamp to cause the lamp to start and operate under the proper circuit conditions of voltage, current, wave form, electrode heat, etc. Basement Wall Basement walls that enclose heated spaces are part of the building

447

Incandescent Lighting Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Incandescent Lighting Basics Incandescent Lighting Basics Incandescent Lighting Basics August 16, 2013 - 10:00am Addthis Incandescent lamps operate simply by heating a metal filament inside a bulb filled with inert gas. Because they operate directly on variety of common power types including common household alternating current or direct current such as batteries or automobiles, they do not require a special power supply or ballast. They turn on up instantly, providing a warm light with excellent color rendition because the light is produced in much the same way as the light from the sun. They can also be easily dimmed using inexpensive controls and are available in a staggering variety of shapes and sizes. However, incandescent lamps have a low efficacy (10-17 lumens per watt) compared with other lighting options and a short average

448

Lighting Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Purple LED lamp Purple LED lamp Lighting Systems Lighting research is aimed at improving the energy efficiency of lighting systems in buildings and homes across the nation. The goal is to reduce lighting energy consumption by 50% over twenty years by improving the efficiency of light sources, and controlling and delivering illumination so that it is available, where and when needed, and at the required intensity. Research falls into four main areas: Sources and Ballasts, Light Distribution Systems, Controls and Communications, and Human Factors. Contacts Francis Rubinstein FMRubinstein@lbl.gov (510) 486-4096 Links Lighting Research Group Batteries and Fuel Cells Buildings Energy Efficiency Applications Commercial Buildings Cool Roofs and Heat Islands Demand Response Energy Efficiency Program and Market Trends

449

DOE SUCCESS STORIES: THE ENERGY MISSION IN THE MARKETPLACE  

NLE Websites -- All DOE Office Websites (Extended Search)

SUCCESS STORIES: THE ENERGY MISSION IN THE MARKETPLACE SUCCESS STORIES: THE ENERGY MISSION IN THE MARKETPLACE Published by: DOE Office of Science Policy 5/95 Contact person: Bob Marley, Director of Office of Science Policy, (202) 5863900 l DOE Success Stories: The Energy Mission in the Marketplace 0 Energy Mission 0 Role of Federal R&D 0 What Successes 0 Improved R&D 0 Economic Successes 0 R&D Management Principles 0 R&D Considerations 0 Deficit Reduction or Revenue Enhancement l Increasinp Energy Efficiency 0 Building Technologies n Fluorescent Lamp Electronic Ballasts n Advanced Energy Efficient Windows n Sulfur Lamp I Computerized AnalyticalTool for Energy Efficient Building Design n High Efficiency Refrigerator Freezer Compressor w Flame Retention Head Oil Burner n Flame Quality Indicator

450

U.S. Department of Energy National Environmental Policy Act categorical exclusion determination  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOYON, LIMITED DOYON, LIMITED Location: Tribe AK-TRIBE-DOYON, AK LIMITED American Recovery and Reinvestment Act: Proposed Action or Project Description Doyon Limited of Alaska proposes to conduct building retrofits of the Doyon Office Building located at 1 Doyon Place in Fairbanks, Alaska. Building retrofits would include redesigning and retrofitting the Doyon Plaza interior lighting system including removing/replacing various lamps, lamp housings, ballasts, and wiring. Conditions: None Categorical Exclusion(s) Applied: B2.5, B5.1 *-For the complete DOE National Environmental Policy Act regulations regarding categorical exclusions, see Subpart D of 10 CFR10 21 This action would not: threaten a violation of applicable statutory, regulatory, or permit requirements for environment, safety, and health,

451

Empire District Electric - Commercial and Industrial Energy Efficiency  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Empire District Electric - Commercial and Industrial Energy Empire District Electric - Commercial and Industrial Energy Efficiency Rebates Empire District Electric - Commercial and Industrial Energy Efficiency Rebates < Back Eligibility Commercial Industrial Savings Category Heating & Cooling Commercial Heating & Cooling Cooling Other Appliances & Electronics Commercial Lighting Lighting Manufacturing Maximum Rebate 5,000; additional funds may be available for final 3 months of program year Program Info State Arkansas Program Type Utility Rebate Program Rebate Amount Custom: lesser of $.30 per kWh savings, 50% of incremental cost, or buydown to two year payback Fluorescent Lamps/Fixtures: $0.50 - $16 High Performance T8 Systems: $9 - $18 High-Bay Fluorescent Lamps/Ballasts: $40 - $125 CFL Fixtures: $8 - $25 Pendant/Wall Mount/Recessed Indirect Fixtures: $16 - $24

452

Final Scientific/Technical Report "Arc Tube Coating System for Color Consistency"  

SciTech Connect

DOE has enabled the use of coating materials using low cost application methods on light sources to positively affect the output of those sources. The coatings and light source combinations have shown increased lumen output of LED fixtures (1.5%-2.0%), LED arrays (1.4%) and LED powered remote phosphor systems ?? Philips L-Prize lamp (0.9%). We have also demonstrated lifetime enhancements (3000 hrs vs 8000 hrs) and shifting to higher CRI (51 to 65) in metal halide high intensity discharge lamps with metal oxide coatings. The coatings on LEDs and LED products are significant as the market is moving increasingly more towards LED technology. Enhancements in LED performance are demonstrated in this work through the use of available materials and low cost application processes. EFOI used low refractive index fluoropolymers and low cost dipping processes for application of the material to surfaces related to light transmission of LEDs and LED products. Materials included Teflon AF, an amorphous fluorinated polymer and fluorinated acrylic monomers. The DOE SSL Roadmap sets goals for LED performance moving into the future. EFOI??s coating technology is a means to shift the performance curve for LEDs. This is not limited to one type of LED, but is relevant across LED technologies. The metal halide work included the use of sol-gel solutions resulting in silicon dioxide and titanium dioxide coatings on the quartz substrates of the metal halide arc tubes. The coatings were applied using low cost dipping processes.

Buelow, Roger; Jenson, Chris; Kazenski, Keith

2013-03-21T23:59:59.000Z

453

Power Capture (PowCap) Board for Non Intrusive Load Monitoring and Power Line Communication Exploration and Development  

E-Print Network (OSTI)

including a) LED lamp, b) incandescent lamp, c) Macbook Pro,W) a LED Lamp 15W b Incandescent Lamp 25W c Macbook 200W dLED lamp (LED) from the incandescent lamp (Lamp) and the Fan

Balakrishnan, Vikram

2013-01-01T23:59:59.000Z

454

Ecosystem under Pressure: Examining the Phytoplankton Community in the High Ballast Water Discharge Environment of Galveston Bay, Texas (USA).  

E-Print Network (OSTI)

??With steady growth in global commerce and intensified ship traffic worldwide, comes the increased risk of invasion by non-indigenous organisms. Annually, >7000 vessels traveled across (more)

Steichen, Jamie L

2013-01-01T23:59:59.000Z

455

Ecosystem under Pressure: Examining the Phytoplankton Community in the High Ballast Water Discharge Environment of Galveston Bay, Texas (USA)  

E-Print Network (OSTI)

and support the idea that a monitoring system within the ports as well as the bay should be put in place. The actions would help to maintain the current health of this ecosystem and aide in preventing a negative impact in the event of successful establishment...

Steichen, Jamie L

2013-01-15T23:59:59.000Z

456

Groton Utilities - Commercial and Industrial Energy Efficiency Rebate  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Groton Utilities - Commercial and Industrial Energy Efficiency Groton Utilities - Commercial and Industrial Energy Efficiency Rebate Programs Groton Utilities - Commercial and Industrial Energy Efficiency Rebate Programs < Back Eligibility Commercial Fed. Government Industrial Local Government Nonprofit State Government Savings Category Heating & Cooling Commercial Heating & Cooling Cooling Heat Pumps Appliances & Electronics Commercial Lighting Lighting Manufacturing Maximum Rebate Lighting/Vending Machine/Door Heater Controls: 50% of total cost Program Info State Connecticut Program Type Utility Rebate Program Rebate Amount Lighting (Retrofit): $0.14/kWh saved T8/T5 Fluorescent Fixture (New Construction/Major Renovation): $7 - $50 Pulse Start Metal Halide Fixture (New Construction/Major Renovation): $20 Dimmable/Controllable Ballast (New Construction/Major Renovation): $40

457

Halide and Oxy-Halide Eutectic Systems for High-Performance, High-Temperature Heat Transfer Fluids- FY13 Q2  

Energy.gov (U.S. Department of Energy (DOE))

This document summarizes the progress of this University of Arizona project, funded by SunShot, for the second quarter of fiscal year 2013.

458

A theoretical study of the gas-phase ion pair SN2 reactions of lithium halide and methyl halide with inversion and retention mechanisms  

Science Journals Connector (OSTI)

Identity and non-identity ion pair SN2 reactions, LiX+CH3X, LiY+CH3X (Y, X=F, Cl, Br and I) were investigated using CCSD(T) calculations. Two possible reaction mechanisms, inversion and retention, were discussed. Introduction of lithium cation will significantly raise the inversion barriers and may lower the retention barriers. The analysis of barrier gaps between the two channels indicates that the retention mechanism is favorable for all of the reactions involving fluorine, in contrast to the anionic SN2 reactions at carbon where inversion reaction pathway is much more favorable for all halogens. The stabilization energies for dipoledipole complexes CH3X?LiY (Y=FI) are found to have a good correlation with the electronegativity of X. The CCSD(T) central barriers and overall barriers show good agreement with the predictions of Marcus equation and its modification, respectively. Further interesting feature of the non-identity ion pair SN2 reactions is a good correlation between inversion central barriers and the composite geometric looseness (%L).

Yan Xiong; Hua-jie Zhu; Yi Ren

2003-01-01T23:59:59.000Z

459

Data:9ed67a3b-6889-48c3-96ff-cd7e6d4438ab | Open Energy Information  

Open Energy Info (EERE)

ed67a3b-6889-48c3-96ff-cd7e6d4438ab ed67a3b-6889-48c3-96ff-cd7e6d4438ab No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Wolverine Pwr Supply Coop, Inc Effective date: 2013/02/26 End date if known: Rate name: Schedule SA- Street Lighting Service - LED Alternative Sector: Description: The Energy Policy Act of 2005 requires that mercury vapor lamp ballasts shall not be manufactured orimported after January 1, 2008. To the extent that the Cooperative has the necessary materials, theCooperative will continue to maintain existing mercury vapor lamp installations in accordance with this Electric Rate Schedule. With respect to mercury vapor lamp installations, rates apply to existingluminaires only and are not open to new business except where the Cooperative elects, at the customer'srequest, to install additional luminaires within an area already served by a mercury vapor unmeteredlighting system. Any such election is subject to the Cooperative having the necessary materials and to thediscretion of the Cooperative

460

Data:D66f9bbf-edd9-471d-805c-ea16d58537e1 | Open Energy Information  

Open Energy Info (EERE)

bbf-edd9-471d-805c-ea16d58537e1 bbf-edd9-471d-805c-ea16d58537e1 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Wolverine Pwr Supply Coop, Inc Effective date: 2013/02/26 End date if known: Rate name: Schedule SA- Street Lighting Service (Metered) Sector: Lighting Description: The Energy Policy Act of 2005 requires that mercury vapor lamp ballasts shall not be manufactured or imported after January 1, 2008. To the extent that the Cooperative has the necessary materials, the Cooperative will continue to maintain existing mercury vapor lamp installations in accordance with this Electric Rate Schedule. With respect to mercury vapor lamp installations, rates apply to existing luminaires only and are not open to new business except where the Cooperative elects, at the customer'srequest, to install additional luminaires within an area already served by a mercury vapor unmeteredlighting system. Any such election is subject to the Cooperative having the necessary materials and to the discretion of the Cooperative

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Hydrogen Storage Engineering Center of Excellence  

Energy Savers (EERE)

Clock bulkpropsslurryabv1 BulkProperties RHO Bulk Density2 RHO Bulk Density1 RHO Bulk Density K Borazine Conc1 K Borazine Conc E Ballast2 E Ballast1 E Ballast...

462

Data:Fb138f46-6f09-477c-88c6-c4ea0a9678c9 | Open Energy Information  

Open Energy Info (EERE)

38f46-6f09-477c-88c6-c4ea0a9678c9 38f46-6f09-477c-88c6-c4ea0a9678c9 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Hart Electric Member Corp Effective date: 2006/10/01 End date if known: Rate name: Schedule L-10 Lighting Service 1000 Watt Metal Halide Flood Sector: Lighting Description: AVAILABILITY Available in all territory served by the Corporation in accordance with the Corporation's Service Rules and Regulations. APPLICABILITY Applicable for electric service supplied to provide dusk to dawn lighting of consumer's property by means of photo-electric controlled, ballast operated mercury or sodium vapor or metal halide luminaries, and poles conforming to the Corporation's specifications, and where secondary service is available, subject to the established Service Rules and Regulations of the Corporation.

463

L&E: Refrigerated Display Case | The Better Buildings Alliance  

NLE Websites -- All DOE Office Websites (Extended Search)

Lighting & Electrical » Adopt the Lighting & Electrical » Adopt the refrigerated display case lighting performance specification and start saving on your case lighting costs Activities Technology Solutions Teams Lighting & Electrical Space Conditioning Plug & Process Loads Food Service Refrigeration Laboratories Energy Management & Information Systems Public Sector Teams Market Solutions Teams Adopt the refrigerated display case lighting performance specification and start saving on your case lighting costs The LED Refrigerated Display Case Lighting Specification delivers nearly 50% energy savings compared to typical display case lighting. If all retail refrigerated display cases switched today to LED systems, over 2.1 TWh of electricity could be saved annually. LED Refrigerated Display Case Lighting Specification

464

L&E: Participate in a field test for high-efficiency troffer lighting. |  

NLE Websites -- All DOE Office Websites (Extended Search)

Lighting & Electrical » Participate Lighting & Electrical » Participate in a field test for high efficiency troffer lighting Activities Technology Solutions Teams Lighting & Electrical Space Conditioning Plug & Process Loads Food Service Refrigeration Laboratories Energy Management & Information Systems Public Sector Teams Market Solutions Teams Participate in a field test for high-efficiency troffer lighting 50% of all commercial fluorescent lighting fixtures are recessed troffers in 1'x4', 2'x2' and 2'x4' configurations, in operation for more than 10 hours a day on average and collectively consuming more than 87 TWh of electricity annually. The Lighting & Electrical team supported the market introduction of high-efficiency troffers by developing a specification that allows for

465

L&E - high efficiency lighting for parking structure | The Better Buildings  

NLE Websites -- All DOE Office Websites (Extended Search)

structure structure Activities Technology Solutions Teams Lighting & Electrical Space Conditioning Plug & Process Loads Food Service Refrigeration Laboratories Energy Management & Information Systems Public Sector Teams Market Solutions Teams Adopt high-efficiency lighting for your parking structure Parking structures and garages are typically lighted by older HID lighting technology without any energy-saving controls. The latest high-efficiency alternatives with energy-saving controls-including light-emitting diode (LED), induction, and fluorescent technology options-can save building owners over 40% on their parking lot lighting bills while delivering additional benefits such as better-lighted spaces. The Lighting & Electrical team developed a performance specification that

466

L&E: Adopt high-efficiency lighting for your parking lot | The Better  

NLE Websites -- All DOE Office Websites (Extended Search)

lot lot Activities Technology Solutions Teams Lighting & Electrical Space Conditioning Plug & Process Loads Food Service Refrigeration Laboratories Energy Management & Information Systems Public Sector Teams Market Solutions Teams Adopt high-efficiency lighting for your parking lot Most parking lots are illuminated by older high-intensity discharge (HID) lighting technology without any energy-saving controls. New light-emitting diode (LED) technology can cut parking lot lighting energy bills by 40%, or much more with controls, while delivering additional benefits including long life, reduced maintenance costs, and improved lighting uniformity. The Lighting & Electrical team developed a performance specification to help building owners take advantage of these improved lighting

467

E-LAMP: integration of innovative ideas for multimedia event detection  

Science Journals Connector (OSTI)

Detecting multimedia events in web videos is an emerging hot research area in the fields of multimedia and computer vision. In this paper, we introduce the core methods and technologies of the framework we developed recently for our Event Labeling through ... Keywords: Multimedia content analysis, Multimedia event detection

Wei Tong; Yi Yang; Lu Jiang; Shoou-I Yu; Zhenzhong Lan; Zhigang Ma; Waito Sze; Ehsan Younessian; Alexander G. Hauptmann

2014-01-01T23:59:59.000Z

468

Side-by-Side Testing of Commercial Office Lighting Systems: Two-lamp Fluorescent Fixtures  

E-Print Network (OSTI)

. Guide to Performance Evaluation of Efficient Lighting Products, Lighting Research Center, Rensselaer Polytechnic Institute, Troy, NY. IES, 1987. IES Lighting Handbook: 1987 Ap~lications Volume, Illuminating Engineering Society of North America, New... Transactions on Industrv A~plications, No. 5, pp. 1189-1 197. Verderber, R.R. and Rubinstein, F.M. and Ward, G., 1989. Photoelectric Control of Daylight Following Lighting Systems, CU- 6243, Electric Power Research Institute, Palo Alto, CA. Rubinstein, F...

Parker, D. S.; Schrum, L.; Sonne, J. K.; Stedman, T. C.

1996-01-01T23:59:59.000Z

469

Contribution to the numerical study of turbulence in high intensity discharge lamps  

SciTech Connect

We present in this paper a comparison between results obtained with a laminar and turbulent models for high-pressure mercury arc. The two models are based on the resolution of bidimensional time-dependent equations by a semi-implicit finite-element code. The numerical computation of turbulent model is solved with large eddy simulation model; this approach takes into account the various scales of turbulence by a filtering method on each scale. The results show the quantitative influence of turbulence on the flow fields and also the difference between laminar and turbulent effects on the dynamic thermal behaviour and on the characteristics of the discharge.

Kaziz, S.; Ben Ahmed, R.; Helali, H.; Gazzah, H.; Charrada, K. [Unite d'Etude des Milieux Ionises et Reactifs, IPEIM, 5019 route de Kairouan Monastir (Tunisia)

2011-07-15T23:59:59.000Z

470

Low Frequency Architecture for Multi-Lamp CCFL Systemswith Capacitive Ignition  

E-Print Network (OSTI)

uniformity degradation, and electromagnetic interference (EMI). The architecture i s capable of driving

471

Market Research on the Use of Energy Saving Lamps: The DELight Project  

Science Journals Connector (OSTI)

This paper describes the DELight project. DELight is studying European domestic lighting and the potential for energy-efficient lighting in terms of the technology, aesthetics and behaviour.

Agneta Persson

1999-01-01T23:59:59.000Z

472

Report 20.4: Lumen and Chromaticity Maintenance of LED PAR38 Lamps  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of Energy (DOE) CALiPER program has been purchasing and testing general illumination solid-state lighting (SSL) products since 2006. CALiPER relies on standardized photometric testing (following the Illuminating Engineering Society of North America [IES] approved method LM-79-081) conducted by accredited, independent laboratories. Results from CALiPER testing are available to the public via detailed reports for each product or through summary reports, which assemble data from several product tests and provide comparative analyses. Increasingly, CALiPER investigations also rely on new test procedures that are not industry standards; these experiments provide data that is essential for understanding the most current issues facing the SSL industry.

473

Solid-state lighting : lamp targets and implications for the semiconductor chip.  

SciTech Connect

A quiet revolution is underway. Over the next 5-10 years inorganic-semiconductor-based solid-state lighting technology is expected to outperform first incandescent, and then fluorescent and high-intensity-discharge, lighting. Along the way, many decision points and technical challenges will be faced. To help understand these challenges, the U.S. Department of Energy, the Optoelectronics Industry Development Association and the National Electrical Manufacturers Association recently updated the U.S. Solid-State Lighting Roadmap. In the first half of this paper, we present an overview of the high-level targets of the inorganic-semiconductor part of that update. In the second half of this paper, we discuss some implications of those high-level targets on the GaN-based semiconductor chips that will be the 'engine' for solid-state lighting.

Tsao, Jeffrey Yeenien

2003-08-01T23:59:59.000Z

474

E-Print Network 3.0 - antigen-dc-lamp messenger rna-electroporated...  

NLE Websites -- All DOE Office Websites (Extended Search)

Virus Research 102 (2004) 5964 RNA interference against retroviruses Summary: Viral gene HIV-1 Tat, Rev siRNA transfection, siRNA electroporation 293T, Jurkat, PBMC Coburn and...

475

E-Print Network 3.0 - ave lamp margareete Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

Medicine 9 GortnerAve.. Buford Ave. Summary: GortnerAve.. Buford Ave. UnderwoodST. Dan Patch Ave. Directions to Gortner Ave Ramp From I-94... Eastbound 1. Exit at Snelling Ave....

476

Mines and Quarries: The Coal and Other Mines (Safety -Lamps and Lighting) Order, 1956  

E-Print Network (OSTI)

This order is made under the Mines and Quarries Act, 1954, s. 190, which empowers the Minister of Fuel and Power to re-enact (to the extent to which they could be enacted in regulations made under the Act and subject to modifications of the kind...

Her Majesty's Stationary Office

1960-01-01T23:59:59.000Z

477

Data:770ed9cc-f605-43f8-b9a4-22051acc9076 | Open Energy Information  

Open Energy Info (EERE)

ed9cc-f605-43f8-b9a4-22051acc9076 ed9cc-f605-43f8-b9a4-22051acc9076 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Piedmont Electric Member Corp Effective date: 2007/07/01 End date if known: Rate name: STREET LIGHTING SERVICE 175 Watt (14,000 Lumen) Metal Halide Lamp Sector: Lighting Description: Acorn type Luminaire on 15 foot tapered fiberglass pole: 175 Watt (14,000 Lumen) Metal Halide Lamp. Source or reference: http://www.pemc.coop/rateSchedules.aspx Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

478

Data:82d57e94-8f32-4c25-ac3b-f4e76cbf8721 | Open Energy Information  

Open Energy Info (EERE)

7e94-8f32-4c25-ac3b-f4e76cbf8721 7e94-8f32-4c25-ac3b-f4e76cbf8721 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Piedmont Electric Member Corp Effective date: 2007/07/01 End date if known: Rate name: STREET LIGHTING SERVICE 1,000 Watt (100,000 Lumen) Metal Halide Lamp Sector: Lighting Description: Floodlight installed on an existing pole:1,000 Watt (100,000 Lumen) Metal Halide Lamp. Source or reference: http://www.pemc.coop/rateSchedules.aspx Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months):

479

Data:1e63a502-7b53-4b1f-aefd-6638588431e3 | Open Energy Information  

Open Energy Info (EERE)

a502-7b53-4b1f-aefd-6638588431e3 a502-7b53-4b1f-aefd-6638588431e3 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Halifax Electric Member Corp Effective date: 2012/10/01 End date if known: Rate name: SECURITY LIGHTING 400-watt metal halide Sector: Lighting Description: AVAILABILITY: This Schedule is available in all territory served by the Cooperative, subject to its established Service Rules and Regulations. APPLICABILITY: This Schedule is applicable to any consumer served by the Cooperative ADJUSTMENT RIDERS AND TAXES: The Cooperative's approved Wholesale Power and TIER Adjustment, as well as the current North Carolina State Sales Tax, shall be applicable to all service supplied under this Schedule. Each lamp, since its power supply is un-metered, shall have a monthly estimated usage assigned for billing purposes as follows: 400-watt metal halide lamp - 150 kWh per month

480

Data:C8ace342-22f7-4d2d-af9a-390a67532948 | Open Energy Information  

Open Energy Info (EERE)

42-22f7-4d2d-af9a-390a67532948 42-22f7-4d2d-af9a-390a67532948 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: City of Norcross, Georgia (Utility Company) Effective date: 2008/04/01 End date if known: Rate name: Security Lighting Service (Metal Halide Flood 1,500W Lamp) Sector: Lighting Description: To property owners and tenants in the proximity of low voltage distribution lines of the City of Norcross. Service may be used to illuminate public thoroughfares and/or private outdoor areas, including, but not limited to, roadways, parking lots and yards. Fixture type: Metal Halide Flood Lamp Wattage: 1,500 Monthly Rate: $36.00 per fixture

Note: This page contains sample records for the topic "halide lamp ballasts" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Data:2aa8488d-85bb-4e85-be0c-d152335f5d3b | Open Energy Information  

Open Energy Info (EERE)

aa8488d-85bb-4e85-be0c-d152335f5d3b aa8488d-85bb-4e85-be0c-d152335f5d3b No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Halifax Electric Member Corp Effective date: 2012/10/01 End date if known: Rate name: SECURITY LIGHTING 175-watt metal halide Sector: Lighting Description: AVAILABILITY: This Schedule is available in all territory served by the Cooperative, subject to its established Service Rules and Regulations. APPLICABILITY: This Schedule is applicable to any consumer served by the Cooperative. ADJUSTMENT RIDERS AND TAXES: The Cooperative's approved Wholesale Power and TIER Adjustment, as well as the current North Carolina State Sales Tax, shall be applicable to all service supplied under this Schedule. Each lamp, since its power supply is un-metered, shall have a monthly estimated usage assigned for billing purposes as follows: 175-watt metal halide lamp - 70 kWh per month

482

Data:5c0b4603-e8ed-44d3-a0ee-22d71d4daf9b | Open Energy Information  

Open Energy Info (EERE)

b4603-e8ed-44d3-a0ee-22d71d4daf9b b4603-e8ed-44d3-a0ee-22d71d4daf9b No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: City of Norcross, Georgia (Utility Company) Effective date: 2008/04/01 End date if known: Rate name: Security Lighting Service (Metal Halide Flood 1,000W Lamp) Sector: Lighting Description: To property owners and tenants in the proximity of low voltage distribution lines of the City of Norcross. Service may be used to illuminate public thoroughfares and/or private outdoor areas, including, but not limited to, roadways, parking lots and yards. Fixture type: Metal Halide Flood Lamp Wattage: 1,000 Monthly Rate: $28.00 per fixture

483

Data:5fe8d568-543d-4a6e-b04f-c1a51a6ac256 | Open Energy Information  

Open Energy Info (EERE)

d568-543d-4a6e-b04f-c1a51a6ac256 d568-543d-4a6e-b04f-c1a51a6ac256 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Piedmont Electric Member Corp Effective date: 2007/07/01 End date if known: Rate name: STREET LIGHTING SERVICE 175 Watt (14,000 Lumen) Metal Halide Lamp Sector: Lighting Description: Decorative Acorn Cutoff type Luminaire on 15 foot tapered fiberglass pole: 175 Watt (14,000 Lumen) Metal Halide Lamp Source or reference: http://www.pemc.coop/rateSchedules.aspx Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh):

484

Data:E68d43f2-c663-48cf-a748-941b3bfb6e0f | Open Energy Information  

Open Energy Info (EERE)

8d43f2-c663-48cf-a748-941b3bfb6e0f 8d43f2-c663-48cf-a748-941b3bfb6e0f No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Piedmont Electric Member Corp Effective date: 2007/07/01 End date if known: Rate name: STREET LIGHTING SERVICE 400 Watt (40,000 Lumen) Metal Halide Lamp Sector: Lighting Description: Floodlight installed on an existing pole: 400 Watt (40,000 Lumen) Metal Halide Lamp. Source or reference: http://www.pemc.coop/rateSchedules.aspx Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW): History (months): Energy (kWh) Minimum (kWh): Maximum (kWh): History (months): Service Voltage

485

Universal: Noncompliance Determination (2013-SE-26004) | Department of  

NLE Websites -- All DOE Office Websites (Extended Search)

Universal: Noncompliance Determination (2013-SE-26004) Universal: Noncompliance Determination (2013-SE-26004) Universal: Noncompliance Determination (2013-SE-26004) September 6, 2013 DOE issued a Notice of Noncompliance Determination to Universal Lighting Technologies, Inc. finding that fluorescent lamp ballast model B140R277HP does not comport with the energy conservation standards. DOE determined the product was noncompliant based on DOE testing. Universal must immediately notify each person (or company) to whom Universal distributed the noncompliant products that the product does not meet Federal standards. In addition, Universal must provide to DOE documents and records showing the number of units Universal distributed and to whom. The manufacturer and/or private labeler of the product may be subject to

486

Data:E310c1ca-83f8-4156-ba68-f1ede3864937 | Open Energy Information  

Open Energy Info (EERE)

10c1ca-83f8-4156-ba68-f1ede3864937 10c1ca-83f8-4156-ba68-f1ede3864937 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Mitchell Electric Member Corp Effective date: 2009/01/01 End date if known: Rate name: SCHEDULE SL-14 SECURITY LIGHTING SERVICE L2 100 WATT WOOD POLE Sector: Lighting Description: AVAILABILITY * Available in all territory served by the Cooperative and subject to the Cooperative's Service Rules and Regulations. SCHEDULE SL-14 SECURITY LIGHTING SERVICE L2 100 WATT WOOD POLE APPLICABILITY * Applicable only to outdoor lighting by ballast-operated vapor lamp fixtures and poles conforming to the Cooperative's specifications. Service will be rendered only at locations accessible for maintenance.

487

Data:D905872b-352a-4ed8-a723-ea5cdb786d8a | Open Energy Information  

Open Energy Info (EERE)

b-352a-4ed8-a723-ea5cdb786d8a b-352a-4ed8-a723-ea5cdb786d8a No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Ocmulgee Electric Member Corp Effective date: 1999/05/01 End date if known: Rate name: 150W Type -'HPS-Sidelite', kWh-60 Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Corporation's specifications. Service will be rendered only at locations that, solely in the opinion of the Corporation, are readily accessible for installation and maintenance. Source or reference: ISU Documentation

488

Data:F6fe3d2b-9a67-4661-aab9-906f806c7860 | Open Energy Information  

Open Energy Info (EERE)

fe3d2b-9a67-4661-aab9-906f806c7860 fe3d2b-9a67-4661-aab9-906f806c7860 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Three Notch Elec Member Corp Effective date: 2012/03/01 End date if known: Rate name: 250W Underground Wiring (Non Mercury vapor fixtures) - (Type - 'HPS-Open',WoodPole(2)) Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Cooperative's specifications. Service will be rendered only at locations that, solely in the opinion of the Cooperative, are readily accessible for installation and maintenance.

489

Data:1373f291-f0ee-45f7-8abb-710bcedb969b | Open Energy Information  

Open Energy Info (EERE)

f0ee-45f7-8abb-710bcedb969b f0ee-45f7-8abb-710bcedb969b No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Ocmulgee Electric Member Corp Effective date: 1999/05/01 End date if known: Rate name: 250W Type -'HPS-Flood', kWh-100 Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Corporation's specifications. Service will be rendered only at locations that, solely in the opinion of the Corporation, are readily accessible for installation and maintenance. Source or reference: ISU Documentation

490

Data:C77c3d84-c745-414a-9bf4-64461174d5f5 | Open Energy Information  

Open Energy Info (EERE)

d84-c745-414a-9bf4-64461174d5f5 d84-c745-414a-9bf4-64461174d5f5 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Three Notch Elec Member Corp Effective date: 2012/03/01 End date if known: Rate name: 250W Overhead Wiring (Non Mercury vapor fixtures) - (Type - 'HPS-Cobra',Wood Pole (2)) Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Cooperative's specifications. Service will be rendered only at locations that, solely in the opinion of the Cooperative, are readily accessible for installation and maintenance.

491

Data:5d47e2c5-b74e-42a0-8742-f681cf68d808 | Open Energy Information  

Open Energy Info (EERE)

b74e-42a0-8742-f681cf68d808 b74e-42a0-8742-f681cf68d808 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Three Notch Elec Member Corp Effective date: 2012/03/01 End date if known: Rate name: 175 Mercury vapor with Underground Wiring- (Type - 'MV-Open', Wood Pole) Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Cooperative's specifications. Service will be rendered only at locations that, solely in the opinion of the Cooperative, are readily accessible for installation and maintenance.

492

Data:361821e3-113c-4a40-a9b1-becf02d08bae | Open Energy Information  

Open Energy Info (EERE)

e3-113c-4a40-a9b1-becf02d08bae e3-113c-4a40-a9b1-becf02d08bae No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Colquitt Electric Membership Corp Effective date: 1993/06/01 End date if known: Rate name: 150W Existing HPS-Cobra, UNDERGROUND WIRING, Metal or Fiberglass Pole Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Cooperative's specifications. Source or reference: ISU Documentation Source Parent: Comments Applicability Demand (kW) Minimum (kW): Maximum (kW):

493

Environmental Energy Technologies Division News  

NLE Websites -- All DOE Office Websites (Extended Search)

Winter 2000: Winter 2000: Vol. 1, No. 4 Lithium Batteries for Hybrid-Electric Vehicles New Fluorescent Lamp Ballast Energy-Efficiency Standards Leading by Example: In-House Energy Management at LBNL Berkeley Lab Acts to Implement Presidential "Greening" Order The Radon Project Web Site Research Highlights Sources and Credits PDF of EETD News Lithium Batteries for Hybrid-Electric Vehicles A long-standing focus of EETD electrochemical research has been to support the development of high-performance rechargeable batteries for electric vehicles. This has proved to be an extremely challenging task because of the need to simultaneously meet multiple battery performance requirements: high energy (watt-hours per unit battery mass or volume), high power (watts per unit battery mass or volume), long life (10 years and hundreds of deep

494

Data:A0610d5a-0d14-40dc-98f2-5ff2f1d0d0f9 | Open Energy Information  

Open Energy Info (EERE)

d14-40dc-98f2-5ff2f1d0d0f9 d14-40dc-98f2-5ff2f1d0d0f9 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Three Notch Elec Member Corp Effective date: 2012/03/01 End date if known: Rate name: 100W Overhead Wiring (Non Mercury vapor fixtures) - (Type - 'HPS-Open',Wood Pole (2)) Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Cooperative's specifications. Service will be rendered only at locations that, solely in the opinion of the Cooperative, are readily accessible for installation and maintenance.

495

Data:D2f0bffd-3563-4d8e-81ec-163f1d467c90 | Open Energy Information  

Open Energy Info (EERE)

bffd-3563-4d8e-81ec-163f1d467c90 bffd-3563-4d8e-81ec-163f1d467c90 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Three Notch Elec Member Corp Effective date: 2012/03/01 End date if known: Rate name: 100W Overhead Wiring (Non Mercury vapor fixtures) - (Type - 'HPS-Cobra',Wood Pole (1)) Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Cooperative's specifications. Service will be rendered only at locations that, solely in the opinion of the Cooperative, are readily accessible for installation and maintenance.

496

Data:994ef76f-ad56-4534-8167-9ee476290886 | Open Energy Information  

Open Energy Info (EERE)

ef76f-ad56-4534-8167-9ee476290886 ef76f-ad56-4534-8167-9ee476290886 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Licking Rural Electric Inc Effective date: 2011/04/01 End date if known: Rate name: OUTDOOR LIGHTING SERVICE- 100 W HPS Carriage Sector: Lighting Description: Available in all territory served by the Cooperative, in accordance with the Cooperative's Service Rules and Regulations. APPLICABILITY Applicable only to outdoor lighting by means of photoelectric controlled ballast operated vapor lamp fixtures and poles conforming to Cooperative specifications and where service can be provided in close proximity to existing overhead distribution. Service will be rendered only at locations that, solely in the opinion of the Cooperative, are readily accessible for maintenance.

497

CX-001752: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2: Categorical Exclusion Determination 2: Categorical Exclusion Determination CX-001752: Categorical Exclusion Determination Crittendon County Office Building Heating, Air Conditioning and Building Lighting Retrofits CX(s) Applied: B2.5, B1.4, B5.1 Date: 04/22/2010 Location(s): Crittendon County, Arizona Office(s): Energy Efficiency and Renewable Energy Energy Efficiency and Conservation Block Grant for: Based on the results of the Crittendon County energy audit conducted, Crittendon will implement the following three building retrofits in the Crittendon County Office Building: 1) replace approximately 515 fluorescent light fixtures with fluorescent T9 lamps and ballast; 2) replace the Crittendon County Office Building air conditioning system, installed in the 1950s, with a new more efficient air conditioning system; and 3) replace the existing Crittendon

498

Data:3ae057df-d560-421f-a823-9f083fbaf24e | Open Energy Information  

Open Energy Info (EERE)

57df-d560-421f-a823-9f083fbaf24e 57df-d560-421f-a823-9f083fbaf24e No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Colquitt Electric Membership Corp Effective date: 1993/06/01 End date if known: Rate name: 175W Existing MV-Open, OVERHEAD WIRING, Wood Pole Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Cooperative's specifications. Source or reference: ISU Documentation Source Parent: Comments Not available for new installations after April 1, 1984. Additional $1.50 will be charged for mounted on 30 foot wood pole

499

Data:D7d3063f-e70a-42c6-bb24-1ba43357e1f1 | Open Energy Information  

Open Energy Info (EERE)

63f-e70a-42c6-bb24-1ba43357e1f1 63f-e70a-42c6-bb24-1ba43357e1f1 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Three Notch Elec Member Corp Effective date: 2012/03/01 End date if known: Rate name: 1000W Underground Wiring (Non Mercury vapor fixtures) - (Type - 'HPS-Flood',WoodPole(2)) Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Cooperative's specifications. Service will be rendered only at locations that, solely in the opinion of the Cooperative, are readily accessible for installation and maintenance.

500

Data:C251fa67-9544-43dd-8774-478976beffc5 | Open Energy Information  

Open Energy Info (EERE)

fa67-9544-43dd-8774-478976beffc5 fa67-9544-43dd-8774-478976beffc5 No revision has been approved for this page. It is currently under review by our subject matter experts. Jump to: navigation, search Loading... 1. Basic Information 2. Demand 3. Energy << Previous 1 2 3 Next >> Basic Information Utility name: Ocmulgee Electric Member Corp Effective date: 1999/05/01 End date if known: Rate name: 400W Type -'HPS-Open/Cobra' Sector: Lighting Description: Applicable only for dusk to dawn lighting by means of photo-electric controlled, ballast operated vapor lamp luminaries and poles conforming to the Corporation's specifications. Service will be rendered only at locations that, solely in the opinion of the Corporation, are readily accessible for installation and maintenance. Source or reference: ISU Documentation