National Library of Energy BETA

Sample records for growth knowledge platform

  1. An in-flight radiography platform to measure hydrodynamic instability growth in inertial confinement fusion capsules at the National Ignition Facility

    SciTech Connect (OSTI)

    Raman, K. S.; Smalyuk, V. A.; Casey, D. T.; Haan, S. W.; Hurricane, O. A.; Kroll, J. J.; Peterson, J. L.; Remington, B. A.; Robey, H. F.; Clark, D. S.; Hammel, B. A.; Landen, O. L.; Marinak, M. M.; Munro, D. H.; Salmonson, J.; Hoover, D. E.; Nikroo, A.; Peterson, K. J.

    2014-07-15

    A new in-flight radiography platform has been established at the National Ignition Facility (NIF) to measure Rayleigh–Taylor and Richtmyer–Meshkov instability growth in inertial confinement fusion capsules. The platform has been tested up to a convergence ratio of 4. An experimental campaign is underway to measure the growth of pre-imposed sinusoidal modulations of the capsule surface, as a function of wavelength, for a pair of ignition-relevant laser drives: a “low-foot” drive representative of what was fielded during the National Ignition Campaign (NIC) [Edwards et al., Phys. Plasmas 20, 070501 (2013)] and the new high-foot [Dittrich et al., Phys. Rev. Lett. 112, 055002 (2014); Park et al., Phys. Rev. Lett. 112, 055001 (2014)] pulse shape, for which the predicted instability growth is much lower. We present measurements of Legendre modes 30, 60, and 90 for the NIC-type, low-foot, drive, and modes 60 and 90 for the high-foot drive. The measured growth is consistent with model predictions, including much less growth for the high-foot drive, demonstrating the instability mitigation aspect of this new pulse shape. We present the design of the platform in detail and discuss the implications of the data it generates for the on-going ignition effort at NIF.

  2. MHK Technologies/New Knowledge Wind and Wave Renewable Mobile...

    Open Energy Info (EERE)

    New Knowledge Wind and Wave Renewable Mobile Wind and Wave Power Plant Platform < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage New Knowledge...

  3. A nanostructure thermal property measurement platform. (Conference) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect A nanostructure thermal property measurement platform. Citation Details In-Document Search Title: A nanostructure thermal property measurement platform. Measurements of the electrical and thermal transport properties of one-dimensional nanostructures (e.g., nanotubes and nanowires) typically are obtained without detailed knowledge of the specimen's atomic-scale structure or defects. To address this deficiency we have developed a microfabricated, chip-based characterization

  4. ARM - CLASIC Measurement Platforms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Measurement Platforms Related Links CLASIC Home AAF Home ARM Data Discovery Browse Data Post-Campaign CLASIC/CHAPS Special Session at AGU Annual Meeting, December 15-19 CLASIC Workshop, March 26-27 Data Sets Deployment Resources Measurement Platforms PNNL WRF-CuP Forecast Cloud Physics Lidar MODIS Airborne Simulator Data Mesonet Monitoring ARM Data Plots Experiment Planning CLASIC Proposal Abstract Science Questions Science and Implementation Plan (pdf) Measurement Platforms (pdf) CLASIC-Land

  5. Ladder attachment platform

    DOE Patents [OSTI]

    Swygert,; Richard, W [Springfield, SC

    2012-08-28

    A ladder attachment platform is provided that includes a base for attachment to a ladder that has first and second side rails and a plurality of rungs that extend between in a lateral direction. Also included is a user platform for having a user stand thereon that is carried by the base. The user platform may be positioned with respect to the ladder so that it is not located between a first plane that extends through the first side rail and is perpendicular to the lateral direction and a second plane that extends through the second side rail and is perpendicular to the lateral direction.

  6. Transactional Network Platform: Applications

    SciTech Connect (OSTI)

    Katipamula, Srinivas; Lutes, Robert G.; Ngo, Hung; Underhill, Ronald M.

    2013-10-31

    In FY13, Pacific Northwest National Laboratory (PNNL) with funding from the Department of Energy’s (DOE’s) Building Technologies Office (BTO) designed, prototyped and tested a transactional network platform to support energy, operational and financial transactions between any networked entities (equipment, organizations, buildings, grid, etc.). Initially, in FY13, the concept demonstrated transactions between packaged rooftop air conditioners and heat pump units (RTUs) and the electric grid using applications or "agents" that reside on the platform, on the equipment, on a local building controller or in the Cloud. The transactional network project is a multi-lab effort with Oakridge National Laboratory (ORNL) and Lawrence Berkeley National Laboratory (LBNL) also contributing to the effort. PNNL coordinated the project and also was responsible for the development of the transactional network (TN) platform and three different applications associated with RTUs. This document describes two applications or "agents" in details, and also summarizes the platform. The TN platform details are described in another companion document.

  7. Manipulator mounted transfer platform

    DOE Patents [OSTI]

    Dobbins, James C. (Idaho Falls, ID); Hoover, Mark A. (Idaho Falls, ID); May, Kay W. (Idaho Falls, ID); Ross, Maurice J. (Pocatello, ID)

    1990-01-01

    A transfer platform for the conveyance of objects by a manipulator includes a bed frame and saddle clamp secured along an edge of the bed frame and adapted so as to secure the bed frame to a horizontal crosspiece of the manipulator. The platform may thus move with the manipulator in a reciprocal linear path defined by a guide rail. A bed insert may be provided for the support of conveyed objects and a lifting bail may be provided to permit the manipulator arm to install the bed frame upon the crosspiece under remote control.

  8. Mobility platform coupling device and method for coupling mobility platforms

    DOE Patents [OSTI]

    Shirey, David L. (Albuquerque, NM); Hayward, David R. (Albuquerque, NM); Buttz, James H. (Albuquerque, NM)

    2002-01-01

    A coupling device for connecting a first mobility platform to a second mobility platform in tandem. An example mobility platform is a robot. The coupling device has a loose link mode for normal steering conditions and a locking position, tight link mode for navigation across difficult terrain and across obstacles, for traversing chasms, and for navigating with a reduced footprint in tight steering conditions.

  9. Common tester platform concept.

    SciTech Connect (OSTI)

    Hurst, Michael James

    2008-05-01

    This report summarizes the results of a case study on the doctrine of a common tester platform, a concept of a standardized platform that can be applicable across the broad spectrum of testing requirements throughout the various stages of a weapons program, as well as across the various weapons programs. The common tester concept strives to define an affordable, next-generation design that will meet testing requirements with the flexibility to grow and expand; supporting the initial development stages of a weapons program through to the final production and surveillance stages. This report discusses a concept investing key leveraging technologies and operational concepts combined with prototype tester-development experiences and practical lessons learned gleaned from past weapons programs.

  10. Secure Sensor Platform

    Energy Science and Technology Software Center (OSTI)

    2010-08-25

    The Secure Sensor Platform (SSP) software provides a framework of functionality to support the development of low-power autonomous sensors for nuclear safeguards. This framework provides four primary functional blocks of capabilities required to implement autonomous sensors. The capabilities are: communications, security, power management, and cryptography. Utilizing this framework establishes a common set of functional capabilities for seamless interoperability of any sensor based upon the SSP concept.

  11. the Central Basin Platform,

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    q / ~ ~ - ~ / o o f - - 2 3 - / % 8 Overview of the Structural Geology and Tectonics of the Central Basin Platform, Delaware Basin, and Midland Basin, West Texas and New Mexico T . Hoaka, K. Sundbergb, and P. Ortolevac a Kestrel Geoscience, LLC 9683 West Chatfield Avenue, Unit D Littleton, Colorado 80128 b Phillips Petroleum Company 252 Geoscience Building Bartlesville, Oklahoma 74003 c Laboratory for Computational Geodynamics Department of Chemistry Indiana University Bloomington, Indiana 47405

  12. CLASIC Measurement Platforms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 SGP Cloud and Land Surface Interaction Campaign (CLASIC): Measurement Platforms June 2007 Mark A. Miller, Principal Investigator and The CLASIC Steering Committee: Roni Avissar, Larry Berg, Sylvia Edgerton, Marc Fischer, Tom Jackson, Bill Kustas, Pete Lamb, Greg McFarquhar, Qilong Min, Beat Schmid, Margaret Torn, and Dave Turner Work supported by the U.S. Department of Energy, Office of Science, Office of Biological and Environmental Research M.R. Miller et al., DOE/SC-ARM-0704 Contents 1.

  13. ARM - Measurements and Platforms

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Measurements and Platforms Related Links ISDAC Home AAF Home AVP Aircraft Instrumentation, October 14-16, 2008 ARM Data Discovery Browse Data Post-Campaign Data Sets Flight Summary Table (PDF, 440K) ISDAC Wiki Mission Summary Journal Deployment Resources NSA Site ARM Data Plots Quick Links Experiment Planning ISDAC Proposal Abstract Full Proposal (pdf, 1,735K) Science Questions Science Overview Document for ISDAC (pdf, 525K) ISDAC Flight Planning Document (PDF, 216K) Collaborations Logistics

  14. ORNL Flexible Research Platforms

    Energy Savers [EERE]

    Flexible Research Platforms Presented by: Joshua New January 28, 2015 Empirical Validation of Whole-Building Energy Simulation Programs Patrick Hughes Ed Vineyard Melissa Lapsa PM: Joshua New PIs - Piljae Im and Mahabir Bhandari (Model) PI - Jibo Sanyal (Provenance) PI - Charles Castello (Sensor QA) PI - Joshua New (Visual Analytics) PI - Philip Boudreaux (Occupancy) PIs - Tony Gehl and Chris Halford (Sensors) PI - F&O (Installation) 2 Presentation name ORNL works with industry to accelerate

  15. HPC - Platforms Penta Chart

    SciTech Connect (OSTI)

    Trujillo, Angelina Michelle

    2015-10-08

    Strategy, Planning, Acquiring- very large scale computing platforms come and go and planning for immensely scalable machines often precedes actual procurement by 3 years. Procurement can be another year or more. Integration- After Acquisition, machines must be integrated into the computing environments at LANL. Connection to scalable storage via large scale storage networking, assuring correct and secure operations. Management and Utilization – Ongoing operations, maintenance, and trouble shooting of the hardware and systems software at massive scale is required.

  16. North Sea platforms revamped

    SciTech Connect (OSTI)

    O'Hare, J.

    1999-12-01

    Many of the early North Sea platforms are reaching their end-of-field life. Most are still equipped with their original drilling package. In a few cases the package has either been removed or decommissioned. The early installations were designed for much simpler and less demanding wells than the horizontal, extended-reach or designer wells common today. Extended-reach wells now can be drilled realistically from ageing platforms, without incurring massive capital expenditure. This can be achieved using the existing drilling package to the limit of its capabilities and supplementing where necessary with relatively minor upgrades or the use of temporary equipment. Drilling even a few more wells from existing platforms not only prolongs field life, it enables any surplus processing capacity to be made available to develop near-field potential with extended-reach drilling (ERD) or by tying back subsea satellite wells, or for processing third-party fluids. The paper describes well design, surface equipment, mud pumps, shakers and solids control equipment, drill cuttings disposal systems, derrick and hoisting system, top drive and drillstring, downhole equipment, well planning, casing wear, logistics, rig preparations, and ERD vs. subsea tie-backs.

  17. Eclipse Parallel Tools Platform

    Energy Science and Technology Software Center (OSTI)

    2005-02-18

    Designing and developing parallel programs is an inherently complex task. Developers must choose from the many parallel architectures and programming paradigms that are available, and face a plethora of tools that are required to execute, debug, and analyze parallel programs i these environments. Few, if any, of these tools provide any degree of integration, or indeed any commonality in their user interfaces at all. This further complicates the parallel developer's task, hampering software engineering practices,more » and ultimately reducing productivity. One consequence of this complexity is that best practice in parallel application development has not advanced to the same degree as more traditional programming methodologies. The result is that there is currently no open-source, industry-strength platform that provides a highly integrated environment specifically designed for parallel application development. Eclipse is a universal tool-hosting platform that is designed to providing a robust, full-featured, commercial-quality, industry platform for the development of highly integrated tools. It provides a wide range of core services for tool integration that allow tool producers to concentrate on their tool technology rather than on platform specific issues. The Eclipse Integrated Development Environment is an open-source project that is supported by over 70 organizations, including IBM, Intel and HP. The Eclipse Parallel Tools Platform (PTP) plug-in extends the Eclipse framwork by providing support for a rich set of parallel programming languages and paradigms, and a core infrastructure for the integration of a wide variety of parallel tools. The first version of the PTP is a prototype that only provides minimal functionality for parallel tool integration of a wide variety of parallel tools. The first version of the PTP is a prototype that only provides minimal functionality for parallel tool integration, support for a small number of parallel architectures, and basis Fortran integration. Future versions will extend the functionality substantially, provide a number of core parallel tools, and provide support across a wide rang of parallel architectures and languages.« less

  18. Turbine blade platform seal

    DOE Patents [OSTI]

    Zagar, Thomas W. (Winter Springs, FL); Schiavo, Anthony L. (Oviedo, FL)

    2001-01-01

    A rotating blade group 90 for a turbo-machine having an improved device for sealing the gap 110 between the edges 112,114 of adjacent blade platforms 96,104. The gap 110 between adjacent blades 92,100 is sealed by a seal pin 20 its central portion 110 and by a seal plate 58,60 at each of the front 54 and rear 56 portions. The seal plates 58,60 are inserted into corresponding grooves 62,64 formed in the adjacent edges 112,114 of adjoining blades 92,100 and held in place by end plates 40,42. The end of the seal plates 58,60 may be chamfered 78,80 to improve the seal against the end plate 40,42. The seal pin 20 provides the required damping between the blades 92,100 and the seal plates 58,60 provide improved sealing effectiveness.

  19. Energy Tracking Software Platform

    SciTech Connect (OSTI)

    Ryan Davis; Nathan Bird; Rebecca Birx; Hal Knowles

    2011-04-04

    Acceleration has created an interactive energy tracking and visualization platform that supports decreasing electric, water, and gas usage. Homeowners have access to tools that allow them to gauge their use and track progress toward a smaller energy footprint. Real estate agents have access to consumption data, allowing for sharing a comparison with potential home buyers. Home builders have the opportunity to compare their neighborhood's energy efficiency with competitors. Home energy raters have a tool for gauging the progress of their clients after efficiency changes. And, social groups are able to help encourage members to reduce their energy bills and help their environment. EnergyIT.com is the business umbrella for all energy tracking solutions and is designed to provide information about our energy tracking software and promote sales. CompareAndConserve.com (Gainesville-Green.com) helps homeowners conserve energy through education and competition. ToolsForTenants.com helps renters factor energy usage into their housing decisions.

  20. Knowledge Framework Implementation with Multiple Architectures - 13090

    SciTech Connect (OSTI)

    Upadhyay, H.; Lagos, L.; Quintero, W.; Shoffner, P.; DeGregory, J.

    2013-07-01

    Multiple kinds of knowledge management systems are operational in public and private enterprises, large and small organizations with a variety of business models that make the design, implementation and operation of integrated knowledge systems very difficult. In recent days, there has been a sweeping advancement in the information technology area, leading to the development of sophisticated frameworks and architectures. These platforms need to be used for the development of integrated knowledge management systems which provides a common platform for sharing knowledge across the enterprise, thereby reducing the operational inefficiencies and delivering cost savings. This paper discusses the knowledge framework and architecture that can be used for the system development and its application to real life need of nuclear industry. A case study of deactivation and decommissioning (D and D) is discussed with the Knowledge Management Information Tool platform and framework. D and D work is a high priority activity across the Department of Energy (DOE) complex. Subject matter specialists (SMS) associated with DOE sites, the Energy Facility Contractors Group (EFCOG) and the D and D community have gained extensive knowledge and experience over the years in the cleanup of the legacy waste from the Manhattan Project. To prevent the D and D knowledge and expertise from being lost over time from the evolving and aging workforce, DOE and the Applied Research Center (ARC) at Florida International University (FIU) proposed to capture and maintain this valuable information in a universally available and easily usable system. (authors)

  1. Railcar Switchman Platform - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Railcar Switchman Platform The swtichman platform is designed to attach to the railcar ladder providing a stable platform Savannah River National Laboratory Contact SRNL About This Technology Technology Marketing SummaryEngineers at the Savannah River Site have devised a new railcar switchman platform for enhanced safety of railroad personnel. The switchman platform is designed to attach to the railcar ladder providing a stable platform from which the switchman can perform their

  2. International Economic Platform for Renewable Energies IWR |...

    Open Energy Info (EERE)

    Platform for Renewable Energies IWR Jump to: navigation, search Name: International Economic Platform for Renewable Energies (IWR) Place: Mnster, Germany Zip: 48159 Sector:...

  3. Tidal Energy Test Platform | Open Energy Information

    Open Energy Info (EERE)

    Test Platform Jump to: navigation, search Basic Specifications Facility Name Tidal Energy Test Platform Overseeing Organization University of New Hampshire Hydrodynamics...

  4. China Low Carbon Platform | Open Energy Information

    Open Energy Info (EERE)

    Low Carbon Platform Jump to: navigation, search Name China Low Carbon Platform AgencyCompany Organization Institute of Development Studies, Climate Change and Development Centre,...

  5. INL Subsurface Wireless Sensor Platform

    SciTech Connect (OSTI)

    Dennis C. Kunerth; John M. Svoboda; James T. Johnson

    2005-10-01

    The Idaho National Laboratory is developing a versatile micro-power sensor interface platform for periodic subsurface sensing of environmental variables important to waste disposal sites such as volumetric moisture, water potential, and temperature. The key characteristics of the platform architecture are that the platform is passive until externally energized --no internal power source is required -- and that it communicates with a "reader" via short-range telemetry - no wires penetrate the subsurface. Other significant attributes include the potential for a long service life and a compact size that makes it well suited for retrofitting existing landfill structures. Functionally, the sensor package is "read" by a short-range induction coil that activates and powers the sensor platform as well as detects the sensor output via a radio frequency signal generated by the onboard programmable interface controller microchip. As a result, the platform has a functional subsurface communication range of approximately 10 to 12 ft. and can only accept sensors that require low power to operate.

  6. Biomass Program 2007 Accomplishments - Biochemical Conversion Platform

    SciTech Connect (OSTI)

    none,

    2009-10-27

    This document details accomplishments of the Biomass Program Biochemical Conversion Platform accomplishments in 2007.

  7. National Bioenergy Center Biochemical Platform Integration Project

    SciTech Connect (OSTI)

    Not Available

    2008-07-01

    April through June 2008 update on activities of the National Bioenergy Center's Biochemical Platform Integration Project.

  8. Biomass Program 2007 Accomplishments - Integrated Biorefinery Platform

    SciTech Connect (OSTI)

    none,

    2008-06-01

    This document details the accomplishments of the Biomass Program Integrated Biorefinery Platform in 2007.

  9. Biomass Program 2007 Accomplishments - Thermochemical Conversion Platform

    SciTech Connect (OSTI)

    none,

    2009-10-27

    This document details the accomplishments of the Biomass Program Thermochemical Conversion Platform in 2007.

  10. SEED Platform Collaborative | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commercial Buildings » Analysis Tools » Standard Energy Efficiency Data Platform » SEED Platform Collaborative SEED Platform Collaborative Overview The Department of Energy built the Standard Energy Efficiency Data (SEED) Platform(tm) to help unlock data-driven program design and implementation in the energy efficiency sector. While there is significant interest in adopting the SEED Platform, many organizations need assistance getting existing datasets and software connected, updating

  11. 2009 Analysis Platform Review Report

    SciTech Connect (OSTI)

    Ferrell, John

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program’s Analysis platform review meeting, held on February 18, 2009, at the Marriott Residence Inn, National Harbor, Maryland.

  12. 2009 Feedstocks Platform Review Report

    SciTech Connect (OSTI)

    Ferrell, John

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program‘s Feedstock platform review meeting, held on April 8–10, 2009, at the Grand Hyatt Washington, Washington, D.C.

  13. 2011 Biomass Program Platform Peer Review: Feedstock

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Feedstock Platform Review Report BIOMASS PROGRAM FEEDSTOCK 2011 Platform Review Report An Independent Evaluation of Platform Activities for FY 2010 and FY 2011 Review Date April 6-8, 2011 February 2012 Department of Energy Washington, D.C. 20585 Dear Colleague: This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy, Offce of Energy Effciency and Renewable Energy, Biomass Program's Feedstock Platform

  14. Graph processing platforms at scale: practices and experiences

    SciTech Connect (OSTI)

    Lim, Seung-Hwan; Lee, Sangkeun; Brown, Tyler C; Sukumar, Sreenivas R; Ganesh, Gautam

    2015-01-01

    Graph analysis unveils hidden associations of data in many phenomena and artifacts, such as road network, social networks, genomic information, and scientific collaboration. Unfortunately, a wide diversity in the characteristics of graphs and graph operations make it challenging to find a right combination of tools and implementation of algorithms to discover desired knowledge from the target data set. This study presents an extensive empirical study of three representative graph processing platforms: Pegasus, GraphX, and Urika. Each system represents a combination of options in data model, processing paradigm, and infrastructure. We benchmarked each platform using three popular graph operations, degree distribution, connected components, and PageRank over a variety of real-world graphs. Our experiments show that each graph processing platform shows different strength, depending the type of graph operations. While Urika performs the best in non-iterative operations like degree distribution, GraphX outputforms iterative operations like connected components and PageRank. In addition, we discuss challenges to optimize the performance of each platform over large scale real world graphs.

  15. MHK Technologies/Titan Platform | Open Energy Information

    Open Energy Info (EERE)

    construction and crane ships The platform along with the wind turbine and wave energy converters are assembled on shore with the platform legs raised The platform and...

  16. Regional Climate Change Adaptation Platform for Asia | Open Energy...

    Open Energy Info (EERE)

    Climate Change Adaptation Platform for Asia Jump to: navigation, search Logo: Regional Climate Change Adaptation Platform for Asia Name Regional Climate Change Adaptation Platform...

  17. Turbine engine airfoil and platform assembly

    DOE Patents [OSTI]

    Campbell, Christian X. (Oviedo, FL); James, Allister W. (Chuluota, FL); Morrison, Jay A. (Oviedo, FL)

    2012-07-31

    A turbine airfoil (22A) is formed by a first process using a first material. A platform (30A) is formed by a second process using a second material that may be different from the first material. The platform (30A) is assembled around a shank (23A) of the airfoil. One or more pins (36A) extend from the platform into holes (28) in the shank (23A). The platform may be formed in two portions (32A, 34A) and placed around the shank, enclosing it. The two platform portions may be bonded to each other. Alternately, the platform (30B) may be cast around the shank (23B) using a metal alloy with better castability than that of the blade and shank, which may be specialized for thermal tolerance. The pins (36A-36D) or holes for them do not extend to an outer surface (31) of the platform, avoiding stress concentrations.

  18. The Harness Workbench: Unified and Adaptive Access to Diverse HPC Platforms (final report)

    SciTech Connect (OSTI)

    George Bosilca

    2012-11-07

    In this project, we conducted preliminary research to create a flexible environment that encapsulates the knowledge of the application developers, site system administrators, and the vendors to assist application building and execution on HPC systems, in particular the DOE leadership computing platforms. The key research involved how to describe and use the knowledge from these varied sources to improve productivity of the end-user scientists, while creating a flexible and modular environment supporting all these features.

  19. Bucket platform cooling scheme and related method

    DOE Patents [OSTI]

    Abuaf, Nesim (Lincoln City, OR); Barb, Kevin Joseph (Halfmoon, NY); Chopra, Sanjay (Greenville, SC); Kercher, David Max (Ipswich, MA); Kellock, Iain Robertson (Simpsonville, SC); Lenahan, Dean Thomas (Cincinnati, OH); Nellian, Sankar (Mauldin, SC); Starkweather, John Howard (Sharonville, OH); Lupe, Douglas Arthur (Ballston Lake, NY)

    2002-01-01

    A turbine bucket includes an airfoil extending from a platform, having high and low pressure sides; a wheel mounting portion; a hollow shank portion located radially between the platform and the wheel mounting portion, the platform having an under surface. An impingement cooling plate is located in the hollow shank portion, spaced from the under surface, and the impingement plate is formed with a plurality of impingement cooling holes therein.

  20. Gas turbine bucket with impingement cooled platform

    DOE Patents [OSTI]

    Jones, Raphael Durand (Guilderland, NY)

    2002-01-01

    In a turbine bucket having an airfoil portion and a root portion, with a substantially planar platform at an interface between the airfoil portion and root portion, a platform cooling arrangement including at least one bore in the root portion and at least one impingement cooling tube seated in the bore, the tube extending beyond the bore with an outlet in close proximity to a targeted area on an underside of the platform.

  1. Economic Analysis of Policy Effects Analysis Platform

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Economic Analysis of Policy Effects Analysis Platform March 24, 2015 Jason Hansen, PhD ... * Annual Milestone (93015): Identify economic benefits of co- products on biorefinery ...

  2. 2009 Biochemical Conversion Platform Review Report

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... the overall platform management on the basis of the ... milestones and organization, RD&D portfolio, strategic ... at conferences, in journal 132 publications and at ...

  3. ARM - Traditional Knowledge

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    HomeroomTraditional Knowledge Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About ARM Global Warming FAQ Just for Fun Meet our Friends Cool Sites Teachers Teachers' Toolbox Lesson Plans Traditional Knowledge An elder from Nauru is interviewed for the TWP kiosks. An elder from Nauru is interviewed for the TWP kiosks. Traditional knowledge can be defined as a cumulative body of knowledge and

  4. Apparatus to position a microelectromechanical platform

    DOE Patents [OSTI]

    Miller, Samuel Lee; Rodgers, Murray Steven

    2003-09-23

    The present invention comprises a microelectromechanical positioner to achieve substantially translational positioning of a platform without rotational motion, thereby maintaining a constant angular orientation of the platform during movement. A linkage mechanism of the positioner can comprise parallelogram linkages to constrain the rotational motion of the platform. Such linkages further can comprise flexural hinges or other turning joints at the linkage pivots to eliminate the need for rubbing surfaces. A plurality of the linkage mechanisms can be used to enable translational motion of the platform with two degrees of freedom. A variety of means can be used to actuate the positioner. Independent actuation of the anchor links of the linkage mechanisms with rotary electrostatic actuators can be used to provide controlled translational movement of the platform.

  5. ESF Mine Power Center Platforms

    SciTech Connect (OSTI)

    T.A. Misiak

    2000-02-10

    The purpose and objective of this analysis is to structurally evaluate the existing Exploratory Studies Facility (ESF) mine power center (MPC) support frames and to design service platforms that will attach to the MPC support frames. This analysis follows the Development Plan titled ''Produce Additional Design for Title 111 Evaluation Report'' (CRWMS M&O 1999a). This analysis satisfies design recommended in the ''Title III Evaluation Report for the Surface and Subsurface Power System'' (CRWMS M&O 1999b, Section 7.6) and concurred with in the ''System Safety Evaluation of Title 111 Evaluation Reports Recommended Work'' (Gwyn 1999, Section 10.1.1). This analysis does not constitute a level-3 deliverable, a level-4 milestone, or a supporting work product. This document is not being prepared in support of the Monitored Geologic Repository (MGR) Site Recommendation (SR), Environmental Impact Statement (EIS), or License Application (LA) and should not be cited as a reference in the MGR SR, EIS, or LA.

  6. Polymer-based platform for microfluidic systems

    DOE Patents [OSTI]

    Benett, William (Livermore, CA); Krulevitch, Peter (Pleasanton, CA); Maghribi, Mariam (Livermore, CA); Hamilton, Julie (Tracy, CA); Rose, Klint (Boston, MA); Wang, Amy W. (Oakland, CA)

    2009-10-13

    A method of forming a polymer-based microfluidic system platform using network building blocks selected from a set of interconnectable network building blocks, such as wire, pins, blocks, and interconnects. The selected building blocks are interconnectably assembled and fixedly positioned in precise positions in a mold cavity of a mold frame to construct a three-dimensional model construction of a microfluidic flow path network preferably having meso-scale dimensions. A hardenable liquid, such as poly (dimethylsiloxane) is then introduced into the mold cavity and hardened to form a platform structure as well as to mold the microfluidic flow path network having channels, reservoirs and ports. Pre-fabricated elbows, T's and other joints are used to interconnect various building block elements together. After hardening the liquid the building blocks are removed from the platform structure to make available the channels, cavities and ports within the platform structure. Microdevices may be embedded within the cast polymer-based platform, or bonded to the platform structure subsequent to molding, to create an integrated microfluidic system. In this manner, the new microfluidic platform is versatile and capable of quickly generating prototype systems, and could easily be adapted to a manufacturing setting.

  7. 2011 Biomass Program Platform Peer Review. Sustainability

    SciTech Connect (OSTI)

    Eng, Alison Goss

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Sustainability Platform Review meeting.

  8. 2011 Biomass Program Platform Peer Review: Feedstock

    SciTech Connect (OSTI)

    McCann, Laura

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Feedstock Platform Review meeting.

  9. 2011 Biomass Program Platform Peer Review: Algae

    SciTech Connect (OSTI)

    Yang, Joyce

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Algae Platform Review meeting.

  10. Cloud Based Applications and Platforms (Presentation)

    SciTech Connect (OSTI)

    Brodt-Giles, D.

    2014-05-15

    Presentation to the Cloud Computing East 2014 Conference, where we are highlighting our cloud computing strategy, describing the platforms on the cloud (including Smartgrid.gov), and defining our process for implementing cloud based applications.

  11. 2011 Biomass Program Platform Peer Review. Infrastructure

    SciTech Connect (OSTI)

    Lindauer, Alicia

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Infrastructure Platform Review meeting.

  12. 2011 Biomass Program Platform Peer Review: Analysis

    SciTech Connect (OSTI)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Analysis Platform Review meeting.

  13. Advanced Sensors, Control, Platforms, and Modeling

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Sensors, Control, Platforms, and Modeling 1 for Manufacturing (Smart Manufacturing): 2 Technology Assessment 3 Contents 4 1. Introduction to the Technology/System ............................................................................................... 2 5 1.1 Overview ....................................................................................................................................... 2 6 1.2 Challenges and opportunities

  14. LEDSGP/about/Latin America and Caribbean Regional Platform |...

    Open Energy Info (EERE)

    Latin America and Caribbean Regional Platform < LEDSGP | about(Redirected from Latin America and Caribbean Regional Platform) Redirect page Jump to: navigation, search REDIRECT...

  15. MHK Technologies/Mobil Stabilized Energy Conversion Platform...

    Open Energy Info (EERE)

    Mobil Stabilized Energy Conversion Platform < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Mobil Stabilized Energy Conversion Platform.jpg...

  16. Standard Energy Efficiency Database Platform - 2013 BTO Peer...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Database Platform - 2013 BTO Peer Review Standard Energy Efficiency Database Platform - 2013 BTO Peer Review PDF icon commlbldgs09prindle040313.pdf More Documents & Publications...

  17. Methane and Methanotrophic Bacteria as a Biotechnological Platform...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Methane and Methanotrophic Bacteria as a Biotechnological Platform Methane and Methanotrophic Bacteria as a Biotechnological Platform Breakout Session 2-B: NewEmerging Pathways...

  18. 2011 Biomass Program Platform Peer Review: Biochemical Conversion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Biochemical Conversion 2011 Biomass Program Platform Peer Review: Biochemical Conversion ... experts at the U.S. Department of Energy Biomass Program's Biochemical Platform Review ...

  19. CINT Discovery Platforms. (Conference) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    CINT Discovery Platforms. Citation Details In-Document Search Title: CINT Discovery Platforms. Abstract not provided. Authors: Sullivan, John P Publication Date: 2011-10-01 OSTI ...

  20. LEDSGP/about/regional-platforms | Open Energy Information

    Open Energy Info (EERE)

    Guiding Structure Regional Platforms LEDS GP regional platforms lead regional peer learning, training, and collaboration; engage technical working groups, the LEDS GP...

  1. Velo: Knowledge and Tool

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Velo: Knowledge and Tool Integration for Collaborative Scientific Projects Carina Lansing, Kerstin Kleese van Dam 1 Scientific Project Life Cycle 2 Conceptual Modeling Simulation ...

  2. Functional design criteria for standard hydrogen monitoring system portable platform

    SciTech Connect (OSTI)

    Schneider, T.C.

    1997-01-17

    Functional design description for a Standard-E cabinet arrangement Standard Hydrogen Monitoring System Portable Platform.

  3. Biochemical Platform Analysis Presentation for BETO 2015 Project Peer Review

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Biochemical Platform Analysis Biochemical Platform Review March 23, 2015 Alexandria, VA Ryan Davis National Renewable Energy Laboratory This presentation does not contain any proprietary, confidential, or otherwise restricted information NATIONAL RENEWABLE ENERGY LABORATORY Goal Statement Biochemical Platform Analysis Objective: *Provide process design and economic analysis support for the biochemical conversion platform, to guide R&D priorities for both NREL and BETO * Translate

  4. Ultralow-Power Silicon Microphotonic Communications Platform

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ultralow-Power Silicon Microphotonic Communications Platform 1 R&D 100 Entry Ultralow-Power Silicon Microphotonic Communications Platform 2 R&D 100 Entry Submitting Organization Sandia National Laboratories P. O. Box 5800 Albuquerque New Mexico 87185-1082 USA Michael R. Watts Phone: (505) 284-9616 Fax: (505) 284-7690 mwatts@sandia.gov AFFIRMATION: I affirm that all information submitted as a part of, or supplemental to, this entry is a fair and accurate representation of this product.

  5. 2009 Thermochemical Conversion Platform Review Report

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    b - Name and Type: PANTONE 2995 C; Angle: 45.000; Lines/Inch: 60.000 - Name and Type: PANTONE 308 C; Angle: 45.000; Lines/Inch: 60.000 - Name and Type: PANTONE 431 C; Angle: 45.000; Lines/Inch: 60.000 BIOMASS PROGRAM December 2009 2009 Thermochemical Conversion Platform Review Report: An Independent Evaluation of Platform Activities for FY 2008 and FY 2009 Executive Summary i This page intentionally left blank ii Dear Colleague: This document summarizes the recommendations and evaluations

  6. Traffic information computing platform for big data

    SciTech Connect (OSTI)

    Duan, Zongtao Li, Ying Zheng, Xibin Liu, Yan Dai, Jiting Kang, Jun

    2014-10-06

    Big data environment create data conditions for improving the quality of traffic information service. The target of this article is to construct a traffic information computing platform for big data environment. Through in-depth analysis the connotation and technology characteristics of big data and traffic information service, a distributed traffic atomic information computing platform architecture is proposed. Under the big data environment, this type of traffic atomic information computing architecture helps to guarantee the traffic safety and efficient operation, more intelligent and personalized traffic information service can be used for the traffic information users.

  7. Dynamic analysis of tension-leg platforms

    SciTech Connect (OSTI)

    Morgan, J.R.

    1983-01-01

    The dynamic response of tension-leg platforms subjected to wave loading was investigated using a deterministic dynamic analysis. The model employed in this study is based on coupled nonlinear stiffness coefficients and closed form inertia and drag forcing functions derived using Morison's equation. The forcing functions include relative motion behavior between the fluid particles and the structure. These forcing functions are integrated manually thereby avoiding the need for expensive numerical integration. A set of coupled nonlinear differential equations was integrated sequentially in the time domain using the Newmark beta-method. A computer program was developed to simulate the time history response of the platform motion.

  8. 2009 Biochemical Conversion Platform Review Report

    SciTech Connect (OSTI)

    Ferrell, John

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program’s Biochemical Conversion platform review meeting, held on April 14-16, 2009, at the Sheraton Denver Downtown, Denver, Colorado.

  9. 2009 Thermochemical Conversion Platform Review Report

    SciTech Connect (OSTI)

    Ferrell, John

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program’s Thermochemical Conversion platform review meeting, held on April 14-16, 2009, at the Sheraton Denver Downtown, Denver, Colorado.

  10. 2009 Integrated Biorefinery Platform Review Report

    SciTech Connect (OSTI)

    Ferrell, John

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program‘s Integrated Biorefinery (IBR) platform review meeting, held on February 18–19, 2009, at the Westin National Harbor, National Harbor, Maryland.

  11. 2011 Biomass Program Platform Peer Review: Sustainability

    Broader source: Energy.gov [DOE]

    "This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Programs Sustainability Platform Review meeting, held on April 5, 2011, at the Doubletree Hotel in Annapolis, Maryland."

  12. 2011 Biomass Program Platform Peer Review: Feedstock

    Broader source: Energy.gov [DOE]

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Biomass Program’s Feedstock Platform Review meeting, held on April 6–8, 2011, at the Doubletree Annapolis Court in Annapolis, Maryland.

  13. Turbine blade and non-integral platform with pin attachment

    DOE Patents [OSTI]

    Campbell, Christian X; Eng, Darryl; Marra, John J

    2015-01-27

    Platforms (36, 38) span between turbine blades (23, 24, 25) on a disk (32). Each platform may be individually mounted to the disk by a pin attachment (42). Each platform (36) may have a rotationally rearward edge portion (50) that underlies a forward portion (45) of the adjacent platform (38). This limits centrifugal bending of the rearward portion of the platform, and provides coolant sealing. The rotationally forward edge (44A, 44B) of the platform overlies a seal element (51) on the pressure side (28) of the forwardly adjacent blade, and does not underlie a shelf on that blade. The pin attachment allows radial mounting of each platform onto the disk via tilting (60) of the platform during mounting to provide mounting clearance for the rotationally rearward edge portion (50). This facilitates quick platform replacement without blade removal.

  14. CALIOPE and TAISIR airborne experiment platform

    SciTech Connect (OSTI)

    Chocol, C.J.

    1994-07-01

    Between 1950 and 1970, scientific ballooning achieved many new objectives and made a substantial contribution to understanding near-earth and space environments. In 1986, the Lawrence Livermore National Laboratory (LLNL) began development of ballooning technology capable of addressing issues associated with precision tracking of ballistic missiles. In 1993, the Radar Ocean Imaging Project identified the need for a low altitude (1 km) airborne platform for its Radar system. These two technologies and experience base have been merged with the acquisition of government surplus Aerostats by Lawrence Livermore National Laboratory. The CALIOPE and TAISIR Programs can benefit directly from this technology by using the Aerostat as an experiment platform for measurements of the spill facility at NTS.

  15. Economic Analysis of Policy Effects Analysis Platform

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Economic Analysis of Policy Effects Analysis Platform March 24, 2015 Jason Hansen, PhD Idaho National Laboratory This presentation does not contain any proprietary, confidential, or otherwise restricted information DOE Bioenergy Technologies Office (BETO) 2015 Project Peer Review 4.1.2.20 2 | Bioenergy Technologies Office * The goal of this project is to 1) identify risk factors in the biofuel supply system, 2) translate risk factors to implications, and 3) identify strategies and polices to

  16. The Standard Energy Efficiency Database Platform

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SEED: The Standard Energy Efficiency Database Platform Bill Prindle Bill Prindle ICF International William.prindle@icfi.com 202-492-9698 2 | Building Technologies Office eere.energy.gov Purpose & Objectives Problem Statement: Data invisibility is a fundamental barrier in building end-use markets. Measuring and recognizing efficiency in U.S. buildings requires standardizing our energy data infrastructure via software conventions. Impact of Project: SEED is intended to provide public agencies

  17. SERS diagnostic platforms, methods and systems microarrays, biosensors and biochips

    DOE Patents [OSTI]

    Vo-Dinh, Tuan (Knoxville, TN)

    2007-09-11

    A Raman integrated sensor system for the detection of targets including biotargets includes at least one sampling platform, at least one receptor probe disposed on the sampling platform, and an integrated circuit detector system communicably connected to the receptor. The sampling platform is preferably a Raman active surface-enhanced scattering (SERS) platform, wherein the Raman sensor is a SERS sensor. The receptors can include at least one protein receptor and at least one nucleic acid receptor.

  18. EM Quality Assurance Centralized Training Platform Project Plan for

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2009-2010 | Department of Energy Program Management » Quality Assurance » EM Quality Assurance Centralized Training Platform Project Plan for 2009-2010 EM Quality Assurance Centralized Training Platform Project Plan for 2009-2010 Project plan for the development of a centralized quality assurance training platform to develop a consistent approach and methodology to training personnel. PDF icon EM Quality Assurance Centralized Training Platform Project Plan for 2009-2010 More Documents

  19. 2009 Biochemical Conversion Platform Review Report | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Biochemical Conversion Platform Review Report 2009 Biochemical Conversion Platform Review Report This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program's Biochemical Conversion platform review meeting, held on April 14-16, 2009, at the Sheraton Denver Downtown, Denver, Colorado. PDF icon obp_biochem_conversion_platform_review_2009.pdf More Documents & Publications 2009 Thermochemical

  20. 2009 Thermochemical Conversion Platform Review Report | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Thermochemical Conversion Platform Review Report 2009 Thermochemical Conversion Platform Review Report This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Programs Thermochemical Conversion platform review meeting, held on April 14-16, 2009, at the Sheraton Denver Downtown, Denver, Colorado. PDF icon obp_thermochem_conversion_platform_review_2009.pdf More Documents &

  1. Standard Energy Efficiency Data Platform | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commercial Buildings » Analysis Tools » Standard Energy Efficiency Data Platform Standard Energy Efficiency Data Platform The SEED Platform(tm) makes it easy to manage and share data on the energy performance of buildings. Overview The Standard Energy Efficiency Data (SEED) Platform(tm) is an open source software application that fills a major market need for data-driven energy efficiency program design and implementation. In today's digital age, the amount of data available to inform decision

  2. OCILOW-Wheeled Platform Controls Executable Set

    Energy Science and Technology Software Center (OSTI)

    2005-11-30

    The OCILOW Controls Executable Set is the complete set of machine executable instructions to control the motion of wheeled platforms that incorporate Off-Centered In-Line Omni-directional Wheels (OCILOW). The controls utilize command signals for the desired motion of the platform (X, Y and Theta) and calculate and control the steering and rolling motion required of each OCILOW wheels to achieve the desired translational and rotational platform motion. The controls utilize signals from the wheel steering andmore » rolling resolvers, and from three load cells located at each wheels, to coordinate the motion of all wheels, while respecting their non-holonomic constraints (i.e., keeping internal stresses and slippage due to possible errors, uneven floors, bumps, misalignment, etc. bounded). The OCILOW Controls Executable Set, which is copyrighted here, is an embodiment of the generic OCILOW algorithms (patented separately) developed specifically for controls of the Proof-of-Principle-Transporter (POP-T) system that has been developed to demonstrate the overall OCILOW controls feasibility and capabilities.« less

  3. OCILOW-Wheeled Platform Controls Executable Set

    SciTech Connect (OSTI)

    2005-11-30

    The OCILOW Controls Executable Set is the complete set of machine executable instructions to control the motion of wheeled platforms that incorporate Off-Centered In-Line Omni-directional Wheels (OCILOW). The controls utilize command signals for the desired motion of the platform (X, Y and Theta) and calculate and control the steering and rolling motion required of each OCILOW wheels to achieve the desired translational and rotational platform motion. The controls utilize signals from the wheel steering and rolling resolvers, and from three load cells located at each wheels, to coordinate the motion of all wheels, while respecting their non-holonomic constraints (i.e., keeping internal stresses and slippage due to possible errors, uneven floors, bumps, misalignment, etc. bounded). The OCILOW Controls Executable Set, which is copyrighted here, is an embodiment of the generic OCILOW algorithms (patented separately) developed specifically for controls of the Proof-of-Principle-Transporter (POP-T) system that has been developed to demonstrate the overall OCILOW controls feasibility and capabilities.

  4. Year 2 Report: Protein Function Prediction Platform

    SciTech Connect (OSTI)

    Zhou, C E

    2012-04-27

    Upon completion of our second year of development in a 3-year development cycle, we have completed a prototype protein structure-function annotation and function prediction system: Protein Function Prediction (PFP) platform (v.0.5). We have met our milestones for Years 1 and 2 and are positioned to continue development in completion of our original statement of work, or a reasonable modification thereof, in service to DTRA Programs involved in diagnostics and medical countermeasures research and development. The PFP platform is a multi-scale computational modeling system for protein structure-function annotation and function prediction. As of this writing, PFP is the only existing fully automated, high-throughput, multi-scale modeling, whole-proteome annotation platform, and represents a significant advance in the field of genome annotation (Fig. 1). PFP modules perform protein functional annotations at the sequence, systems biology, protein structure, and atomistic levels of biological complexity (Fig. 2). Because these approaches provide orthogonal means of characterizing proteins and suggesting protein function, PFP processing maximizes the protein functional information that can currently be gained by computational means. Comprehensive annotation of pathogen genomes is essential for bio-defense applications in pathogen characterization, threat assessment, and medical countermeasure design and development in that it can short-cut the time and effort required to select and characterize protein biomarkers.

  5. WEF-Green Growth Partnerships Initiative | Open Energy Information

    Open Energy Info (EERE)

    World Economic Forum Partner Global Green Growth Institute, Climate and Development Knowledge Network (CDKN), United Kingdom Government Sector Energy, Land, Climate Topics...

  6. LEDSGP/about/Latin America and Caribbean Regional Platform/LAC...

    Open Energy Info (EERE)

    aboutLatin America and Caribbean Regional PlatformLAC Regional Platform Workshop < LEDSGP | about | Latin America and Caribbean Regional Platform Jump to: navigation,...

  7. Spatial Knowledge Capture Library

    Energy Science and Technology Software Center (OSTI)

    2005-05-16

    The Spatial Knowledge Capture Library is a set of algorithms to capture regularities in shapes and trajectories through space and time. We have applied Spatial Knowledge Capture to model the actions of human experts in spatial domains, such as an AWACS Weapons Director task simulation. The library constructs a model to predict the expert’s response to sets of changing cues, such as the movements and actions of adversaries on a battlefield, The library includes amore » highly configurable feature extraction functionality, which supports rapid experimentation to discover causative factors. We use k-medoid clustering to group similar episodes of behavior, and construct a Markov model of system state transitions induced by agents’ actions.« less

  8. Building a Community-Focused Data Platform

    SciTech Connect (OSTI)

    Turk, Matthew J.; Warren, Michael S.; Skillman, Samuel W.

    2014-06-10

    The National Data Service (NDS) presents a broad-reaching vision of integrating discovery, publishing, and sharing of data. Metcalfe's Law states that the value of a network increases with the number of connections in the network, not the number of nodes. The NDS must develop and steward connections not only between data, as is in its vision statement, but between individuals as well. We propose that this be accomplished by explicitly developing it as a platform on which data exploration can be constructed by individual researchers.

  9. SEED: Standard Energy Efficiency Data Platform

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SEED: Standard Energy Efficiency Data Platform 2014 Building Technologies Office Peer Review Rich Brown, REBrown@lbl.gov Lawrence Berkeley National Laboratory Project Summary Timeline: Start date: 2013 Planned end date: Sept 30, 2014 Key Milestones 1. v1.0 launch; April 2014 2. Adoption by 2-3 cities; May 2014 3. v1.1 launch; July 2014 Budget: Total DOE $ to date: $1,400,000 Total future DOE $: TBD, depends on market adoption Target Market/Audience: organizations that manage and publish building

  10. Analytical laboratory and mobile sampling platform

    SciTech Connect (OSTI)

    Stetzenbach, K.; Smiecinski, A.

    1996-04-30

    This is the final report for the Analytical Laboratory and Mobile Sampling Platform project. This report contains only major findings and conclusions resulting from this project. Detailed reports of all activities performed for this project were provided to the Project Office every quarter since the beginning of the project. This report contains water chemistry data for samples collected in the Nevada section of Death Valley National Park (Triangle Area Springs), Nevada Test Site springs, Pahranagat Valley springs, Nevada Test Site wells, Spring Mountain springs and Crater Flat and Amargosa Valley wells.

  11. Robotic vehicle with multiple tracked mobility platforms

    DOE Patents [OSTI]

    Salton, Jonathan R. (Albuquerque, NM); Buttz, James H. (Albuquerque, NM); Garretson, Justin (Albuquerque, NM); Hayward, David R. (Wetmore, CO); Hobart, Clinton G. (Albuquerque, NM); Deuel, Jr., Jamieson K. (Albuquerque, NM)

    2012-07-24

    A robotic vehicle having two or more tracked mobility platforms that are mechanically linked together with a two-dimensional coupling, thereby forming a composite vehicle of increased mobility. The robotic vehicle is operative in hazardous environments and can be capable of semi-submersible operation. The robotic vehicle is capable of remote controlled operation via radio frequency and/or fiber optic communication link to a remote operator control unit. The tracks have a plurality of track-edge scallop cut-outs that allow the tracks to easily grab onto and roll across railroad tracks, especially when crossing the railroad tracks at an oblique angle.

  12. Building the Agile Biomanufacturing Platform Workshop

    Broader source: Energy.gov [DOE]

    A consortium of nine national labs is excited to announce the Agile Biomanufacturing Industry Listening Workshop on March 15, 2016 in Berkeley, CA. Lawrence Berkeley National Lab, Ames National Lab, Argonne National Lab, Idaho National Lab, Los Alamos National Lab, the National Renewable Energy Lab, Oak Ridge National Lab, Pacific Northwest National Lab, and Sandia National Labs seek to build an agile biomanufacturing platform for biological approaches to produce advanced biofuels, renewable chemicals, and materials that represent low greenhouse gas alternatives to molecules currently derived from petroleum. The labs envision a distributed Agile Biomanufacturing consortium that includes a Foundry to productionize the design-build-test-learn cycle for engineering biology while incorporating process integration, predictable scaling, and techno-economic analyses and life cycle assessments for bioprocess design. The DOE National Laboratories have built deep and unique capabilities that can be brought to bear to build powerful infrastructure and scientific engineering activities that will render design and implementation of new bio-based products scalable, predictable, and more cost-effective. An agile biomanufacturing platform will enable companies, national labs, and universities to develop biological processes efficiently and with reduced risk to create products with better performance than their predecessors.

  13. Mechanically latchable tiltable platform for forming micromirrors and micromirror arrays

    DOE Patents [OSTI]

    Garcia, Ernest J. (Albuquerque, NM); Polosky, Marc A. (Tijeras, NM); Sleefe, Gerard E. (Cedar Crest, NM)

    2006-12-12

    A microelectromechanical (MEM) apparatus is disclosed which includes a platform that can be electrostatically tilted from being parallel to a substrate on which the platform to being tilted at an angle of 1 20 degrees with respect to the substrate. Once the platform has been tilted to a maximum angle of tilt, the platform can be locked in position using an electrostatically-operable latching mechanism which engages a tab protruding below the platform. The platform has a light-reflective upper surface which can be optionally coated to provide an enhanced reflectivity and form a micromirror. An array of such micromirrors can be formed on a common substrate for applications including optical switching (e.g. for fiber optic communications), optical information processing, image projection displays or non-volatile optical memories.

  14. VOLTTRON Lite: Integration Platform for the Transactional Network

    SciTech Connect (OSTI)

    Haack, Jereme N.; Katipamula, Srinivas; Akyol, Bora A.; Lutes, Robert G.

    2013-10-31

    In FY13, Pacific Northwest National Laboratory (PNNL) with funding from the Department of Energy’s (DOE’s) Building Technologies Office (BTO) designed, prototyped and tested a transactional network platform. The platform is intended to support energy, operational and financial transactions between any networked entities (equipment, organizations, buildings, grid, etc.). Initially, in FY13, the concept demonstrated transactions between packaged rooftop units (RTUs) and the electric grid using applications or “agents” that reside on the platform, on the equipment, on local building controller or in the Cloud. This document describes the core of the transactional network platform, the Volttron Liteℱ software and associated services hosted on the platform. Future enhancements are also discussed. The appendix of the document provides examples of how to use the various services hosted on the platform.

  15. Surface Di-directional Reflectance Properties Over the ARM SGP Area from Satellite Multi-Platform Observations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Bi-Directional Reflectance Properties Over the ARM SGP Area from Satellite Multi-Platform Observations Y. Luo, A. P. Trishchenko, and R. Latifovic Canada Centre for Remote Sensing Natural Resources Canada Ottawa, Ontario, Canada Z. Li Earth System Science Interdisciplinary Center University of Maryland College Park, Maryland Introduction Surface albedo is an important parameter in atmospheric radiation research. Good knowledge of surface bi-directional reflectance distribution function (BRDF) is

  16. Vibration Model Validation for Linear Collider Detector Platforms

    SciTech Connect (OSTI)

    Bertsche, Kirk; Amann, J.W.; Markiewicz, T.W.; Oriunno, M.; Weidemann, A.; White, G.; /SLAC

    2012-05-16

    The ILC and CLIC reference designs incorporate reinforced-concrete platforms underneath the detectors so that the two detectors can each be moved onto and off of the beamline in a Push-Pull configuration. These platforms could potentially amplify ground vibrations, which would reduce luminosity. In this paper we compare vibration models to experimental data on reinforced concrete structures, estimate the impact on luminosity, and summarize implications for the design of a reinforced concrete platform for the ILC or CLIC detectors.

  17. 2011 Biomass Program Platform Review Report: Algae | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Review Report: Algae 2011 Biomass Program Platform Review Report: Algae This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Biomass Program's Algae Platform Review meeting, held on April 7-8, 2011, at the Doubletree Hotel in Annapolis, Maryland. PDF icon 2011_algae_review.pdf More Documents & Publications 2011 Biomass Program Platform Peer Review:

  18. Platform for Pre-Symptomatic Detection of Citrus Disease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Citrus Disease Detection Platform Platform for Pre-Symptomatic Detection of Citrus Disease LANS is currently seeking an industry partner(s) to assist with the commercial deployment of the detection platform described below. Submit your Commercialization Proposal to lanldx@lanl.gov before 11:59 PM on Thursday, March 10, 2016. Submit your Proposal thumbnail of Kathleen McDonald Head of Intellectual Property, Business Development Executive Kathleen McDonald Richard P. Feynman Center for Innovation

  19. Methane and Methanotrophic Bacteria as a Biotechnological Platform |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Methane and Methanotrophic Bacteria as a Biotechnological Platform Methane and Methanotrophic Bacteria as a Biotechnological Platform Breakout Session 2-B: New/Emerging Pathways Methane and Methanotrophic Bacteria as a Biotechnological Platform Dr. Lori Giver, Vice President of Biological Engineering, Calysta Energy, Inc. PDF icon giver_bioenergy_2015.pdf More Documents & Publications CX-100166 Categorical Exclusion Determination Biobased Chemicals Landscape in 2015:

  20. 2011 Biomass Program Platform Peer Review: Infrastructure | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Infrastructure 2011 Biomass Program Platform Peer Review: Infrastructure This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Biomass Program's Infrastructure Platform Review meeting, held on February 3, 2011, in Washington, D.C. PDF icon 2011_infrastructure_review.pdf More Documents & Publications 2011 Biomass Program Platform Peer

  1. Design and Control of a Ship Motion Simulation Platform from...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Design and Control of a Ship Motion Simulation Platform from an Energy Efficiency Perspective Citation Details In-Document Search Title: Design and Control of a ...

  2. PR-PR: Cross-Platform Laboratory Automation System

    SciTech Connect (OSTI)

    Linshiz, G; Stawski, N; Goyal, G; Bi, CH; Poust, S; Sharma, M; Mutalik, V; Keasling, JD; Hillson, NJ

    2014-08-01

    To enable protocol standardization, sharing, and efficient implementation across laboratory automation platforms, we have further developed the PR-PR open-source high-level biology-friendly robot programming language as a cross-platform laboratory automation system. Beyond liquid-handling robotics, PR-PR now supports microfluidic and microscopy platforms, as well as protocol translation into human languages, such as English. While the same set of basic PR-PR commands and features are available for each supported platform, the underlying optimization and translation modules vary from platform to platform. Here, we describe these further developments to PR-PR, and demonstrate the experimental implementation and validation of PR-PR protocols for combinatorial modified Golden Gate DNA assembly across liquid-handling robotic, microfluidic, and manual platforms. To further test PR-PR cross-platform performance, we then implement and assess PR-PR protocols for Kunkel DNA mutagenesis and hierarchical Gibson DNA assembly for microfluidic and manual platforms.

  3. Genomics-enabled sensor platform for rapid detection of viruses...

    Office of Scientific and Technical Information (OSTI)

    platforms for preclinical and field testing that utilize the assays developed in goal 1. We generated and characterized suitable primersmore for West Nile Virus RNA detection. ...

  4. The Tariff Analysis Project: A Database and Analysis Platform...

    Open Energy Info (EERE)

    Tariff Analysis Project: A Database and Analysis Platform for Electricity Tariffs Jump to: navigation, search Tool Summary LAUNCH TOOL Name: The Tariff Analysis Project: A Database...

  5. EM Quality Assurance Centralized Training Platform Project Plan...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Project plan for the development of a centralized quality assurance training platform to develop a consistent approach and methodology to training personnel. PDF icon EM Quality ...

  6. Sandia Energy - Study Compares Floating-Platform Options for...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    required platform as well as mooring configurations were considered. Hypothetical deployment site off the coast of Maine and location of the NBDC buoy used for wave...

  7. 2011 Biomass Program Platform Peer Review: Thermochemical Conversion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Thermochemical Conversion 2011 Biomass Program Platform Peer Review: Thermochemical ... experts at the U.S. Department of Energy Biomass Programs Thermochemical Conversion ...

  8. 2011 Biomass Program Platform Peer Review: Integrated Biorefineries...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Integrated Biorefineries 2011 Biomass Program Platform Peer Review: Integrated ... experts at the U.S. Department of Energy Biomass Programs Integrated Biorefinery ...

  9. An Integrated Platform for Engine Performance Simulations and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    An Integrated Platform for Engine Performance Simulations and Optimization under Diesel Conditions The direct injection stochastic reactor model is capable of accurate simulation ...

  10. MHK Technologies/Platform generators | Open Energy Information

    Open Energy Info (EERE)

    homepage Platform generators.jpg Technology Profile Primary Organization Aqua Magnetics Inc Technology Resource Click here Wave Technology Type Click here Reciprocating...

  11. Transparent Gold as a Platform for Adsorbed ProteinSpectroelectrochem...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Transparent Gold as a Platform for Adsorbed Protein Spectroelectrochemistry: Investigation of Cytochrome c and Azurin Authors: Ashur, I., Schulz, O., McIntosh, C. L., Pinkas, I.,...

  12. Genomics-enabled sensor platform for rapid detection of viruses...

    Office of Scientific and Technical Information (OSTI)

    platforms for preclinical and field testing that utilize the assays developed in goal 1. We generated and characterized suitable primers more for West Nile Virus RNA detection. ...

  13. UNDP-Climate Finance Options Platform | Open Energy Information

    Open Energy Info (EERE)

    Renewable Energy Topics: Finance Website: www.climatefinanceoptions.orgcfo Cost: Free UNDP-Climate Finance Options Platform Screenshot References: UNDP-Climate Finance...

  14. Robust automated knowledge capture.

    SciTech Connect (OSTI)

    Stevens-Adams, Susan Marie; Abbott, Robert G.; Forsythe, James Chris; Trumbo, Michael Christopher Stefan; Haass, Michael Joseph; Hendrickson, Stacey M. Langfitt

    2011-10-01

    This report summarizes research conducted through the Sandia National Laboratories Robust Automated Knowledge Capture Laboratory Directed Research and Development project. The objective of this project was to advance scientific understanding of the influence of individual cognitive attributes on decision making. The project has developed a quantitative model known as RumRunner that has proven effective in predicting the propensity of an individual to shift strategies on the basis of task and experience related parameters. Three separate studies are described which have validated the basic RumRunner model. This work provides a basis for better understanding human decision making in high consequent national security applications, and in particular, the individual characteristics that underlie adaptive thinking.

  15. ARM - Lesson Plans: Rate of Coral Growth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rate of Coral Growth Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About ARM Global Warming FAQ Just for Fun Meet our Friends Cool Sites Teachers Teachers' Toolbox Lesson Plans Lesson Plans: Rate of Coral Growth Objective The objective is to understand the fact that the growth of coral depends on water depth and the effect of sea level changes on corals. Materials Each student or group of students

  16. Turtle Mountain Band of Chippewa Indians 10 Y Energy, Environmental, and Economic Development Platform

    Energy Savers [EERE]

    Turtle Mountain Band of Chippewa Indians - TMBCI 10Y Energy, Environmental and Economic Development Platform DOE Office of Indian Energy Tribal Leader Forum Series Indian Pueblo Cultural Center - Albuquerque, NM July 27, 2015 10Y Governance, Financial and Environmental Impacts TMBCI Current Annual Energy Spend: $6.5 Million est. Daily Demand: 18MW est. 0 50 100 150 200 10Y1 10Y2 10Y3 10Y4 10Y5 10Y6 10Y7 10Y8 10Y9 10Y10 10Y Growth Projection Non-tribal Utility Hydrocarbons TMBCI Efficiency and

  17. U-156: Red Hat update for JBoss Enterprise Portal Platform | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy 56: Red Hat update for JBoss Enterprise Portal Platform U-156: Red Hat update for JBoss Enterprise Portal Platform April 26, 2012 - 7:00am Addthis PROBLEM: Red Hat update for JBoss Enterprise Portal Platform PLATFORM: JBoss Enterprise Portal Platform 5.x ABSTRACT: Update for JBoss Enterprise Portal Platform Reference Links: Secunia Advisory SA48954 CVE-2011-4314 CVE-2012-0818 IMPACT ASSESSMENT: Medium Discussion: Red Hat has issued an update for JBoss Enterprise Portal Platform. This

  18. DOE Hybrid and Electric Vehicle Test Platform

    SciTech Connect (OSTI)

    Gao, Yimin

    2012-03-31

    Based on the contract NT-42790 to the Department of Energy, “Plug-in Hybrid Ethanol Research Platform”, Advanced Vehicle Research Center (AVRC) Virginia has successfully developed the phase I electric drive train research platform which has been named as Laboratory Rapid Application Testbed (LabRAT). In phase II, LabRAT is to be upgraded into plug-in hybrid research platform, which will be capable of testing power systems for electric vehicles, and plug-in hybrid electric vehicles running on conventional as well as alternative fuels. LabRAT is configured as a rolling testbed with plentiful space for installing various component configurations. Component connections are modularized for flexibility and are easily replaced for testing various mechanisms. LabRAT is designed and built as a full functional vehicle chassis with a steering system, brake system and four wheel suspension. The rear drive axle offers maximum flexibility with a quickly changeable gear ratio final drive to accommodate different motor speed requirements. The electric drive system includes an electric motor which is mechanically connected to the rear axle through an integrated speed/torque sensor. Initially, a 100 kW UQM motor and corresponding UQM motor controller is used which can be easily replaced with another motor/controller combination. A lithium iron phosphate (LiFePO4) battery pack is installed, which consists of 108 cells of 100 AH capacity, giving the total energy capacity of 32.5 kWh. Correspondingly, a fully functional battery management system (BMS) is installed to perform battery cell operation monitoring, cell voltage balancing, and reporting battery real time operating parameters to vehicle controller. An advanced vehicle controller ECU is installed for controlling the drive train. The vehicle controller ECU receives traction or braking torque command from driver through accelerator and brake pedal position sensors and battery operating signals from the BMS through CAN BUS, and then generates motor torque command (traction or braking) to the motor controller based on the control algorithm software embedded in the vehicle controller ECU. The vehicle controller ECU is a re-programmable electronic control unit. Any control algorithm software developed can be easily downloaded to vehicle controller ECU to test any newly developed control strategy. The flexibility of the control system significantly enhances the practical applicability of the LabRAT. A new test methodology has been developed for the LabRAT simulating any vehicles running on road with different weights from compact passenger car to light duty truck on an AC or eddy current dynamometers without much effort for modification of the system. LabRAT is equipped with a fully functional data acquisition system supplied by CyberMetrix. The measurement points along the drive train are DC electric power between battery pack and motor controller input, AC electric power between motor controller and electric motor, mechanical power between motor and rear axle. The data acquisition system is designed with more capability than current requirements in order to meet the requirements for phase II.

  19. Standard Energy Efficiency Database Platform - 2013 BTO Peer Review |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Database Platform - 2013 BTO Peer Review Standard Energy Efficiency Database Platform - 2013 BTO Peer Review PDF icon commlbldgs09_prindle_040313.pdf More Documents & Publications Buildings Performance Database - 2013 BTO Peer Review Commercial Buildings Integration Program Overview - 2013 BTO Peer Review Future Funding: Effective Models for Leveraging Public Funds

  20. Passport to Knowledge | Open Energy Information

    Open Energy Info (EERE)

    Passport to Knowledge Jump to: navigation, search Logo: Passport to Knowledge Name: Passport to Knowledge Place: Morristown, New Jersey Region: Northeast - NY NJ CT PA Area...

  1. Tracking Provenance in ORNL's Flexible Research Platforms

    SciTech Connect (OSTI)

    Hensley, Zachary P; Sanyal, Jibonananda; New, Joshua Ryan

    2013-08-01

    Provenance is dened as information about the origin of objects, a concept that applies to both physical and digital objects and often overlaps both. The use of provenance in systems designed for research is an important but forgotten feature. Provenance allows for proper and exact tracking of information, its use, its lineage, its derivations and other metadata that are important for correctly adhering to the scien- tic method. In our project's prescribed use of provenance, researchers can determine detailed information about the use of sensor data in their experiments on ORNL's Flexible Research Platforms (FRPs). Our project's provenance system, Provenance Data Management System (ProvDMS), tracks information starting with the creation of information by an FRP sensor. The system determines station information, sensor information, and sensor channel information. The system allows researchers to derive generations of experiments from the sensor data and tracks their hierarchical flow. Key points can be seen in the history of the information as part of the information's workflow. The concept of provenance and its usage in science is relatively new and while used in other cases around the world, our project's provenance diers in a key area. To keep track of provenance, most systems must be designed or redesigned around the new provenance system. Our system is designed as a cohesive but sepa- rate entity and allows for researchers to continue using their own methods of analysis without being constrained in their ways in order to track the provenance. We have designed ProvDMS using a lightweight provenance library, Core Provenance Library (CPL) v.6 In addition to keeping track of sensor data experiments and its provenance, ProvDMS also provides a web-enabled visualization of the inheritance.

  2. Volttron: An Agent Platform for the Smart Grid

    SciTech Connect (OSTI)

    Haack, Jereme N.; Akyol, Bora A.; Carpenter, Brandon J.; Tews, Cody W.; Foglesong, Lance W.

    2013-05-06

    VOLLTRON platform enables the deployment of intelligent sensors and controllers in the smart grid and provides a stable, secure and flexible framework that expands the sensing and control capabilities. VOLTTRON platform provides services fulfilling the essential requirements of resource management and security for agent operation in the power grid. The facilities provided by the platform allow agent developers to focus on the implementation of their agent system and not on the necessary "plumbing' code. For example, a simple collaborative demand response application was written in less than 200 lines of Python.

  3. Assessment of an ORION-based experimental platform for measuring...

    Office of Scientific and Technical Information (OSTI)

    experimental platform for measuring the opacity of high-temperature and high-density plasma Citation Details In-Document Search Title: Assessment of an ORION-based experimental...

  4. 2011 Biomass Program Platform Peer Review: Biochemical Conversion

    SciTech Connect (OSTI)

    Pezzullo, Leslie

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Biochemical Conversion Platform Review meeting.

  5. The power grid of the future is a platform that

    Broader source: Energy.gov (indexed) [DOE]

    grid of the future is a platform that delivers reliable, affordable, and clean electricity to American consumers where they want it, when they want it, and how they want it. To...

  6. Assessment of an ORION-based experimental platform for measuring...

    Office of Scientific and Technical Information (OSTI)

    ...h-temperature and high-density plasma Citation Details In-Document Search Title: Assessment of an ORION-based experimental platform for measuring the opacity of high-temperature ...

  7. Open Platform of Climate-Smart Planning Instruments | Open Energy...

    Open Energy Info (EERE)

    Website: prod-http-80-800498448.us-east-1.elb.amazonaws.comwimages55dOpen Language: English References: Open Platform of Climate-Smart Planning Instruments1 Overview...

  8. 2011 Biomass Program Platform Peer Review. Integrated Biorefineries

    SciTech Connect (OSTI)

    Rossmeissl, Neil

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s IBR Platform Review meeting.

  9. Platform-independent method for computer aided schematic drawings

    DOE Patents [OSTI]

    Vell, Jeffrey L. (Slingerlands, NY); Siganporia, Darius M. (Clifton Park, NY); Levy, Arthur J. (Fort Lauderdale, FL)

    2012-02-14

    A CAD/CAM method is disclosed for a computer system to capture and interchange schematic drawing and associated design information. The schematic drawing and design information are stored in an extensible, platform-independent format.

  10. 2011 Biomass Program Platform Peer Review. Thermochemical Conversion

    SciTech Connect (OSTI)

    Grabowski, Paul E.

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Thermochemical Conversion Platform Review meeting.

  11. Fluidics platform and method for sample preparation and analysis

    DOE Patents [OSTI]

    Benner, W. Henry; Dzenitis, John M.; Bennet, William J.; Baker, Brian R.

    2014-08-19

    Herein provided are fluidics platform and method for sample preparation and analysis. The fluidics platform is capable of analyzing DNA from blood samples using amplification assays such as polymerase-chain-reaction assays and loop-mediated-isothermal-amplification assays. The fluidics platform can also be used for other types of assays and analyzes. In some embodiments, a sample in a sealed tube can be inserted directly. The following isolation, detection, and analyzes can be performed without a user's intervention. The disclosed platform may also comprises a sample preparation system with a magnetic actuator, a heater, and an air-drying mechanism, and fluid manipulation processes for extraction, washing, elution, assay assembly, assay detection, and cleaning after reactions and between samples.

  12. SEED Platform Frequently Asked Questions | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... identified through use of the SEED Platform brand and logo, will remain interoperable. ... How do modifications or add-ons affect the use of the SEED trademark brand?Because the ...

  13. V-230: IBM TRIRIGA Application Platform Multiple Cross-Site Scripting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    0: IBM TRIRIGA Application Platform Multiple Cross-Site Scripting Vulnerabilities V-230: IBM TRIRIGA Application Platform Multiple Cross-Site Scripting Vulnerabilities August 29, ...

  14. Platforms and Methods for In Situ Characterization of Li-ion...

    Office of Scientific and Technical Information (OSTI)

    Platforms and Methods for In Situ Characterization of Li-ion Battery Materials. Citation Details In-Document Search Title: Platforms and Methods for In Situ Characterization of...

  15. Commercial-Grade, Scalable Support and Training Services Platform |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Commercial-Grade, Scalable Support and Training Services Platform Commercial-Grade, Scalable Support and Training Services Platform Lead Performer: Big Ladder Software - Denver, CO DOE Funding: $149,554 Cost Share: N/A Project Term: June 2014 - March 2015 Funding Opportunity: Small Business Innovation Research FY 2014 Phase 1 Release 2 Awards Project Objective The Department of Energy has funded the development of two industry-leading simulation engines, EnergyPlus and

  16. Robotic platform for traveling on vertical piping network

    DOE Patents [OSTI]

    Nance, Thomas A; Vrettos, Nick J; Krementz, Daniel; Marzolf, Athneal D

    2015-02-03

    This invention relates generally to robotic systems and is specifically designed for a robotic system that can navigate vertical pipes within a waste tank or similar environment. The robotic system allows a process for sampling, cleaning, inspecting and removing waste around vertical pipes by supplying a robotic platform that uses the vertical pipes to support and navigate the platform above waste material contained in the tank.

  17. A Functional Test Platform for the Community Land Model

    SciTech Connect (OSTI)

    Xu, Yang [ORNL] [ORNL; Thornton, Peter E [ORNL] [ORNL; King, Anthony Wayne [ORNL] [ORNL; Steed, Chad A [ORNL] [ORNL; Gu, Lianhong [ORNL] [ORNL; Schuchart, Joseph [ORNL] [ORNL

    2014-01-01

    A functional test platform is presented to create direct linkages between site measurements and the process-based ecosystem model within the Community Earth System Models (CESM). The platform consists of three major parts: 1) interactive user interfaces, 2) functional test model and 3) observational datasets. It provides much needed integration interfaces for both field experimentalists and ecosystem modelers to improve the model s representation of ecosystem processes within the CESM framework without large software overhead.

  18. 2011 Biomass Program Platform Peer Review: Biochemical Conversion |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Biochemical Conversion 2011 Biomass Program Platform Peer Review: Biochemical Conversion This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program's Biochemical Platform Review meeting, held on February 14-16, 2011, at the Crowne Plaza Hotel in Downtown Denver, Colorado. PDF icon 2011_biochem_review.pdf More Documents & Publications 2011 Biomass Program Peer

  19. 2011 Biomass Program Platform Peer Review: Thermochemical Conversion |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Thermochemical Conversion 2011 Biomass Program Platform Peer Review: Thermochemical Conversion "This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Programs Thermochemical Conversion Platform Review meeting, held on February 16...18, 2011, at the Crowne Plaza Hotel in Downtown Denver, Colorado." PDF icon 2011_thermochem_review.pdf More Documents &

  20. Nanoscience Research at CINT Using Discovery Platforms. (Conference) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Nanoscience Research at CINT Using Discovery Platforms. Citation Details In-Document Search Title: Nanoscience Research at CINT Using Discovery Platforms. Authors: Sullivan, John P. Publication Date: 2012-05-01 OSTI Identifier: 1067715 Report Number(s): SAND2012-3588C DOE Contract Number: AC04-94AL85000 Resource Type: Conference Resource Relation: Conference: Proposed for presentation at the Sandia/Universidad Autonoma de Ciudad Juarez Meeting held April 27, 2012 in

  1. PHEV development test platform Utilization | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    development test platform Utilization PHEV development test platform Utilization 2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C. PDF icon vssp_07_lohsebusch.pdf More Documents & Publications Tradeoff between Fuel Consumption and Emissions for PHEV's Off-Cycle Benchmarking of PHEVs; Wide Range of Temperatures and Aggressive Driving Cycles Evaluation of Ethanol Blends for PHEVs using Simulation and

  2. A Systems Biology Platform for Characterizing Regulatory and Metabolic

    Office of Scientific and Technical Information (OSTI)

    Pathways that Influence and Control Microbial Hydrogen Production (Technical Report) | SciTech Connect Technical Report: A Systems Biology Platform for Characterizing Regulatory and Metabolic Pathways that Influence and Control Microbial Hydrogen Production Citation Details In-Document Search Title: A Systems Biology Platform for Characterizing Regulatory and Metabolic Pathways that Influence and Control Microbial Hydrogen Production × You are accessing a document from the Department of

  3. A Systems Biology Platform for Characterizing Regulatory and Metabolic

    Office of Scientific and Technical Information (OSTI)

    Pathways that Influence and Control Microbial Hydrogen Production (Technical Report) | SciTech Connect Technical Report: A Systems Biology Platform for Characterizing Regulatory and Metabolic Pathways that Influence and Control Microbial Hydrogen Production Citation Details In-Document Search Title: A Systems Biology Platform for Characterizing Regulatory and Metabolic Pathways that Influence and Control Microbial Hydrogen Production Authors: Collins, James J [1] + Show Author Affiliations

  4. A Systems Biology Platform for Characterizing Regulatory and Metabolic

    Office of Scientific and Technical Information (OSTI)

    Pathways that Influence and Control Microbial Hydrogen Production (Technical Report) | SciTech Connect A Systems Biology Platform for Characterizing Regulatory and Metabolic Pathways that Influence and Control Microbial Hydrogen Production Citation Details In-Document Search Title: A Systems Biology Platform for Characterizing Regulatory and Metabolic Pathways that Influence and Control Microbial Hydrogen Production Authors: Collins, James J [1] + Show Author Affiliations Boston University

  5. An Integrated Platform for Engine Performance Simulations and Optimization

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    under Diesel Conditions | Department of Energy An Integrated Platform for Engine Performance Simulations and Optimization under Diesel Conditions An Integrated Platform for Engine Performance Simulations and Optimization under Diesel Conditions The direct injection stochastic reactor model is capable of accurate simulation of combustion under diesel conditions and can also be used to simulate and test different fuels. PDF icon p-17_pasternak.pdf More Documents & Publications Ricardo's

  6. Standard Energy Efficiency Data (SEED) Platform - 2014 BTO Peer Review |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Data (SEED) Platform - 2014 BTO Peer Review Standard Energy Efficiency Data (SEED) Platform - 2014 BTO Peer Review Project Objective The Standard Energy Efficiency Data (SEED) software application helps organizations easily manage data on the energy performance of large groups of buildings, thus also improving the consistency and interoperability of the data. The project's objectives this year are to: (1) complete development of a production-grade, first version of SEED

  7. Biomass Program Peer Review Sustainability Platform | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Peer Review Sustainability Platform Biomass Program Peer Review Sustainability Platform Presentation on the Update to the Billion-Ton Study, including differences between the Update and the 2005 Billion-Ton Sudy, assumptions, and findings. PDF icon bt2_webinar.pdf More Documents & Publications U.S. Billion-Ton Update: Biomass Supply for a Bioenergy and Bioproducts Industry Importance of Biomass Production and Supply ECOWAS - GBEP REGIONAL BIOMASS RESOURCE ASSESSMENT WORKSHOP

  8. 2011 Biomass Program Platform Peer Review: Integrated Biorefineries |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Integrated Biorefineries 2011 Biomass Program Platform Peer Review: Integrated Biorefineries "This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Programs Integrated Biorefinery Platform Review meeting, held on February 1...3, 2011, at the U.S. Department of Energy, Washington, D.C." PDF icon 2011_ibr_review.pdf More Documents & Publications 2011 Biomass

  9. Blade platform seal for ceramic/metal rotor assembly

    DOE Patents [OSTI]

    Wertz, John L.

    1982-01-01

    A combination ceramic and metal turbine rotor for use in high temperature gas turbine engines includes a metal rotor disc having a rim with a plurality of circumferentially spaced blade root retention slots therein to receive a plurality of ceramic blades, each including side platform segments thereon and a dovetail configured root slidably received in one of the slots. Adjacent ones of the platform segments including edge portions thereon closely spaced when the blades are assembled to form expansion gaps in an annular flow surface for gas passage through the blades and wherein the assembly further includes a plurality of unitary seal members on the rotor connected to its rim and each including a plurality of spaced, axially extending, flexible fingers that underlie and conform to the edge portions of the platform segments and which are operative at turbine operating temperatures and speeds to distribute loading on the platform segments as the fingers are seated against the underside of the blade platforms to seal the gaps without undesirably stressing thin web ceramic sections of the platform.

  10. Shasta/Mustique subsea equipment platform interface and operability

    SciTech Connect (OSTI)

    Jefferies, A.T.; Loegering, C.; Steib, D.; Schlater, D.

    1996-12-31

    The economic benefits of all inclusive systems engineering approach is now recognized in the offshore industry. Nowhere is this more evident than in the area of deepwater subsea tiebacks to existing facilities. This type of development requires effective management of the interfaces between personnel on the existing facility and the new project team, the interfaces between the new subsea facilities and the existing platform, and the interface of the new operating procedures with the existing platform daily routine. A second factor in the economic viability of many of these projects is the need to minimize operating costs by avoiding the need for subsea system repair intervention. An operability analysis focusing on the subsea system and platform interface engineering was used on the Hardy projects to address the concerns with the potential for interventions. With minimum operating costs as a primary goal, Hardy encouraged participation from both host platform operating groups from the outset of both projects. This cooperation was critical since both projects were planned to more than double the throughput for both host platforms without adding platform operating personnel. The approach of operator involvement also ensured a safe, reliable, and economic transition between the installation and operating phases of the developments.

  11. Deactivation & Decommissioning Knowledge Management Information...

    Broader source: Energy.gov (indexed) [DOE]

    The D&D Knowledge Management Information Tool (KM-IT) is a web-based information tool to ... The D&D KM-IT has been developed through the application of state-of-the-art web ...

  12. Protein-Based Nanomedicine Platforms for Drug Delivery

    SciTech Connect (OSTI)

    Ma Ham, Aihui; Tang, Zhiwen; Wu, Hong; Wang, Jun; Lin, Yuehe

    2009-08-03

    Drug delivery systems have been developed for many years, however some limitations still hurdle the pace of going to clinical phase, for example, poor biodistribution, drug molecule cytotoxicity, tissue damage, quick clearance from the circulation system, solubility and stability of drug molecules. To overcome the limitations of drug delivery, biomaterials have to be developed and applied to drug delivery to protect the drug molecules and to enhance the drug’s efficacy. Protein-based nanomedicine platforms for drug delivery are platforms comprised of naturally self-assembled protein subunits of the same protein or a combination of proteins making up a complete system. They are ideal for drug delivery platforms due to their biocompatibility and biodegradability coupled with low toxicity. A variety of proteins have been used and characterized for drug delivery systems including the ferritin/apoferritin protein cage, plant derived viral capsids, the small Heat shock protein (sHsp) cage, albumin, soy and whey protein, collagen, and gelatin. There are many different types and shapes that have been prepared to deliver drug molecules using protein-based platforms including the various protein cages, microspheres, nanoparticles, hydrogels, films, minirods and minipellets. There are over 30 therapeutic compounds that have been investigated with protein-based drug delivery platforms for the potential treatment of various cancers, infectious diseases, chronic diseases, autoimmune diseases. In protein-based drug delivery platforms, protein cage is the most newly developed biomaterials for drug delivery and therapeutic applications. Their uniform sizes, multifunctions, and biodegradability push them to the frontier for drug delivery. In this review, the recent strategic development of drug delivery has been discussed with a special emphasis upon the polymer based, especially protein-based nanomedicine platforms for drug delivery. The advantages and disadvantages are also discussed for each type of protein based drug delivery system.

  13. Coiled tubing deployed ESP on the Auk platform

    SciTech Connect (OSTI)

    Stewart, D.W.; Watkins, P.; Holtslag, R.J.; Hudson, A.; Wee, P.Y.; McCleery, B.

    1996-12-31

    In March 1995, what is believed to be the world`s first offshore coiled tubing deployed electrical submersible pump (ESP) was successfully commissioned in well AA-03S1 on Shell U.K. Exploration and Production (Shell Expro) Auk platform in the United Kingdom`s Central North Sea. The ESP provides a new and important method of artificial lift for the 21 year old Auk platform, which hitherto had relied upon downhole hydraulic jet pumps to lift approximately half of the platform`s oil production. The coiled tubing deployment proved the viability of performing future workovers with or without the assistance or indeed the presence of a drilling package. The novel completion design successfully catered to the wide variety of customer requirements; Well Engineering for a rigless workover, Petroleum Engineering for reservoir access and Facilities Engineering for a specified flowline height. The experience gained during this project will be a valuable input in determining the future artificial lift strategy for this platform and for other prospects in terms of performance, reliability and operating costs.

  14. D0 Cryogenic System Superconducting Solenoid Platform I/O

    SciTech Connect (OSTI)

    Markley, D.; /Fermilab

    1997-10-09

    The Dzero detector is scheduled for a major upgrade between 1996 and 1999. This note describes the specifications and configuration of the physical Input/Output devices and instrumentation of the 2 Tesla Superconducting Solenoid. The Solenoid and the VLPC cryostats both reside on the detector platform and are cooled by the Dzero Helium Refrigerator. The cryogenic process control s for these two components will be an extension of the TI565 programmable logic controller system used for other Dzero cryogenic controls. Two Input/Output Bases will be installed on the Dzero detector platform near the cryo corner. These I/O bases will handle all the sensor input and process control output devices from the Solenoid and VLPC cryostats. Having the I/O bases installed on the detector platform makes the connecting cabl ing to the platform much easier . All the instruments are wired directly to the I/O base. The bases have only one communications network cabl e that must be routed off the platform to the South side of the Dzero building.

  15. Modular turbine airfoil and platform assembly with independent root teeth

    DOE Patents [OSTI]

    Campbell, Christian X; Davies, Daniel O; Eng, Darryl

    2013-07-30

    A turbine airfoil (22E-H) extends from a shank (23E-H). A platform (30E-H) brackets or surrounds a first portion of the shank (23E-H). Opposed teeth (33, 35) extend laterally from the platform (30E-H) to engage respective slots (50) in a disk. Opposed teeth (25, 27) extend laterally from a second portion of the shank (29) that extends below the platform (30E-H) to engage other slots (52) in the disk. Thus the platform (30E-H) and the shank (23E-H) independently support their own centrifugal loads via their respective teeth. The platform may be formed in two portions (32E-H, 34E-H), that are bonded to each other at matching end-walls (37) and/or via pins (36G) passing through the shank (23E-H). Coolant channels (41, 43) may pass through the shank beside the pins (36G).

  16. National Bioenergy Center Biochemical Platform Integration Project: Quarterly Update #22, January - March 2009

    SciTech Connect (OSTI)

    Not Available

    2009-04-01

    January to March, 2009 edition of the National Bioenergy Center's Biochemical Platform Integration Project quarterly newsletter.

  17. National Bioenergy Center Biochemical Platform Integration Project: Quarterly Update #23, April-June 2009

    SciTech Connect (OSTI)

    Schell, D.

    2009-08-01

    April to June, 2009 edition of the National Bioenergy Center's Biochemical Platform Integration Project quarterly newsletter.

  18. National Bioenergy Center Biochemical Platform Integration Project: Quarterly Update #17, October-December 2007

    SciTech Connect (OSTI)

    Schell, D.

    2008-01-01

    October to December, 2007 edition of the newsletter of the Biochemical Platform Process Integration project.

  19. National Bioenergy Center Biochemical Platform Integration Project: Quarterly Update #25, October - December 2009

    SciTech Connect (OSTI)

    Schell, D.

    2010-01-01

    October to December, 2009 edition of the National Bioenergy Center's Biochemical Platform Integration Project quarterly newsletter.

  20. V-230: IBM TRIRIGA Application Platform Multiple Cross-Site Scripting

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Vulnerabilities | Department of Energy 0: IBM TRIRIGA Application Platform Multiple Cross-Site Scripting Vulnerabilities V-230: IBM TRIRIGA Application Platform Multiple Cross-Site Scripting Vulnerabilities August 29, 2013 - 4:10am Addthis PROBLEM: Multiple vulnerabilities have been reported in IBM TRIRIGA Application Platform, which can be exploited by malicious people to conduct cross-site scripting attacks. PLATFORM: IBM TRIRIGA Application Platform 2.x ABSTRACT: The vulnerabilities are

  1. New Modeling Tool Analyzes Floating Platform Concepts | Department of

    Office of Environmental Management (EM)

    Energy Modeling Tool Analyzes Floating Platform Concepts New Modeling Tool Analyzes Floating Platform Concepts May 20, 2011 - 3:16pm Addthis This is an excerpt from the Second Quarter 2011 edition of the Wind Program R&D Newsletter. The United States has a large and accessible offshore wind resource. According to a report published by DOE's National Renewable Energy Laboratory (NREL) in 2010 (Large-Scale Offshore Wind Power in the United States), winds off the coasts of the United States

  2. LEDSGP/home | Open Energy Information

    Open Energy Info (EERE)

    Growth Knowledge Platform (GGKP) Third Annual Conference "Fiscal Policies and the Green Economy Transition: Generating Knowledge - Creating Impact 29-30 January 2015 World Bank...

  3. Central Characterization Program (CCP), Acceptable Knowledge...

    Office of Environmental Management (EM)

    , Acceptable Knowledge Summary Report for Los Alamos National Laboratory, TA-55 Mixed Transuranic Waste Streams Central Characterization Program (CCP), Acceptable Knowledge Summary...

  4. Central Characterization Program (CCP) Acceptable Knowledge Documentat...

    Office of Environmental Management (EM)

    Acceptable Knowledge Documentation Central Characterization Program (CCP) Acceptable Knowledge Documentation This document was used to determine facts and conditions during the...

  5. UCEAO: Energy Knowledge Bank | Open Energy Information

    Open Energy Info (EERE)

    UCEAO: Energy Knowledge Bank Jump to: navigation, search Name: UCEAO: Energy Knowledge Bank Place: Ohio Website: knowledgebank.uso.edu References: University Clean Energy Alliance...

  6. Essential Body of Knowledge (EBK)

    Broader source: Energy.gov [DOE]

    A Competency and Functional Framework for Cyber Security Workforce Development The EBK accomplishes two important Departmental training goals: 1) defining the baseline knowledge, skills, and abilities required for key cyber security functional roles, and 2) providing the foundational objectives for the development, selection, and presentation of training.

  7. Knowledge information management toolkit and method

    DOE Patents [OSTI]

    Hempstead, Antoinette R.; Brown, Kenneth L.

    2006-08-15

    A system is provided for managing user entry and/or modification of knowledge information into a knowledge base file having an integrator support component and a data source access support component. The system includes processing circuitry, memory, a user interface, and a knowledge base toolkit. The memory communicates with the processing circuitry and is configured to store at least one knowledge base. The user interface communicates with the processing circuitry and is configured for user entry and/or modification of knowledge pieces within a knowledge base. The knowledge base toolkit is configured for converting knowledge in at least one knowledge base from a first knowledge base form into a second knowledge base form. A method is also provided.

  8. Biomass Program 2007 Peer Review - Integrated Biorefinery Platform Summary

    SciTech Connect (OSTI)

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Integrated Biorefinery Platform Review held on August 13-15, 2007 in Golden, Colorado.

  9. Motivation for the Transaction-Based Reference Platform

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Motivation for the Transaction-Based Reference Platform Or How I learned to Stop Worrying and Love Transactions George Hernandez Pacific Northwest National Lab July 23-24, 2015 Technical Advisor - Building Technologies Office US Department of Energy Challenges * Application Challenges - Integrating variable distributed generation * Solar * Wind - Integrating storage at multiple layers - Integrating electric vehicles (EV) - Managing end-use loads * Residential * Commercial * Industrial -

  10. Biomass Program 2007 Program Peer Review - Thermochemical Conversion Platform Summary

    SciTech Connect (OSTI)

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Biomass Program Peer Review for the Thermochemical Platform, held on July 9th and 10th in Golden, Colorado.

  11. Biomass Program 2007 Program Peer Review - Feedstock Platform Summary

    SciTech Connect (OSTI)

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Feedstock Platform Portfolio Peer Review held on August 21st through 23rd in Washington D.C.

  12. ARM - Lesson Plans: Plant Growth and Carbon Dioxide

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Plant Growth and Carbon Dioxide Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About ARM Global Warming FAQ Just for Fun Meet our Friends Cool Sites Teachers Teachers' Toolbox Lesson Plans Lesson Plans: Plant Growth and Carbon Dioxide Objective The objective is to show how carbon dioxide in the air affects plant growth. Materials Each group of students will need the following: Graph paper Pencil

  13. Bioenergy Knowledge Discovery Framework (KDF)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE Bioenergy Technologies Office (BETO) 2015 Project Peer Review Bioenergy Knowledge Discovery Framework (KDF) April 1, 2015 Analysis & Sustainability Aaron Myers Oak Ridge National Laboratory This presentation does not contain any proprietary, confidential, or otherwise restricted information Managed by UT-Battelle for the Department of Energy Goal Statement  Creation and enhancement of geo-spatial, temporal decision support system to connect researchers, industry, and sponsors to share

  14. A Method of Correcting for Tilt From Horizontal in Downwelling Shortwave Irradiance Measurements on Moving Platforms

    SciTech Connect (OSTI)

    Long, Charles N.; Bucholtz, Anthony; Jonsson, Haf; Schmid, Beat; Vogelmann, A. M.; Wood, John

    2010-04-14

    Significant errors occur in downwelling shortwave irradiance measurements made on moving platforms due to tilt from horizontal because, when the sun is not completely blocked by overhead cloud, the downwelling shortwave irradiance has a prominent directional component from the direct sun. A-priori knowledge of the partitioning between the direct and diffuse components of the total shortwave irradiance is needed to properly apply a correction for tilt. This partitioning information can be adequately provided using a newly available commercial radiometer that produces reasonable measurements of the total and diffuse shortwave irradiance, and by subtraction the direct shortwave irradiance, with no moving parts and regardless of azimuthal orientation. We have developed methodologies for determining the constant pitch and roll offsets of the radiometers for aircraft applications, and for applying a tilt correction to the total shortwave irradiance data. Results suggest that the methodology is for tilt up to +/-10°, with 90% of the data corrected to within 10 Wm-2 at least for clear-sky data. Without a proper tilt correction, even data limited to 5° of tilt as is typical current practice still exhibits large errors, greater than 100 Wm-2 in some cases. Given the low cost, low weight, and low power consumption of the SPN1 total and diffuse radiometer, opportunities previously excluded for moving platform measurements such as small Unmanned Aerial Vehicles and solar powered buoys now become feasible using our methodology. The increase in measurement accuracy is important, given current concerns over long-term climate variability and change especially over the 70% of the Earth’s surface covered by ocean where long-term records of these measurements are sorely needed and must be made on ships and buoys.

  15. One UN Training Service Platform for Climate Change (UN CC:LEARN...

    Open Energy Info (EERE)

    UN Training Service Platform for Climate Change (UN CC:LEARN) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: One UN Training Service Platform for Climate Change (UN...

  16. Simulator platform for fast reactor operation and safety technology demonstration

    SciTech Connect (OSTI)

    Vilim, R. B.; Park, Y. S.; Grandy, C.; Belch, H.; Dworzanski, P.; Misterka, J.

    2012-07-30

    A simulator platform for visualization and demonstration of innovative concepts in fast reactor technology is described. The objective is to make more accessible the workings of fast reactor technology innovations and to do so in a human factors environment that uses state-of-the art visualization technologies. In this work the computer codes in use at Argonne National Laboratory (ANL) for the design of fast reactor systems are being integrated to run on this platform. This includes linking reactor systems codes with mechanical structures codes and using advanced graphics to depict the thermo-hydraulic-structure interactions that give rise to an inherently safe response to upsets. It also includes visualization of mechanical systems operation including advanced concepts that make use of robotics for operations, in-service inspection, and maintenance.

  17. Microelectromechanical apparatus for elevating and tilting a platform

    DOE Patents [OSTI]

    Miller, Samuel Lee (Albuquerque, NM); McWhorter, Paul Jackson (Albuquerque, NM); Rodgers, Murray Steven (Albuquerque, NM); Sniegowski, Jeffry J. (Edgewood, NM); Barnes, Stephen M. (Albuquerque, NM)

    2003-04-08

    A microelectromechanical (MEM) apparatus is disclosed which has a platform that can be elevated above a substrate and tilted at an arbitrary angle using a plurality of flexible members which support the platform and control its movement. Each flexible member is further controlled by one or more MEM actuators which act to bend the flexible member. The MEM actuators can be electrostatic comb actuators or vertical zip actuators, or a combination thereof. The MEM apparatus can include a mirror coating to form a programmable mirror for redirecting or switching one or more light beams for use in a projection display. The MEM apparatus with the mirror coating also has applications for switching light beams between optical fibers for use in a local area fiber optic network, or for use in fiber optic telecommunications or data communications systems.

  18. Microelectromechanical apparatus for elevating and tilting a platform

    DOE Patents [OSTI]

    Miller, Samuel Lee; McWhorter, Paul Jackson; Rodgers, Murray Steven; Sniegowski, Jeffry J.; Barnes, Stephen M.

    2004-07-06

    A microelectromechanical (MEM) apparatus is disclosed which has a platform that can be elevated above a substrate and tilted at an arbitrary angle using a plurality of flexible members which support the platform and control its movement. Each flexible member is further controlled by one or more MEM actuators which act to bend the flexible member. The MEM actuators can be electrostatic comb actuators or vertical zip actuators, or a combination thereof. The MEM apparatus can include a mirror coating to form a programmable mirror for redirecting or switching one or more light beams for use in a projection display. The MEM apparatus with-the mirror coating also has applications for switching light beams between optical fibers for use in a local area fiber optic network, or for use in fiber optic telecommunications or data communications systems.

  19. An Update on Unmanned Platforms at Oliktok Point

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Update on Unmanned Platforms at Oliktok Point For original submission and image(s), see ARM Research Highlights http://www.arm.gov/science/highlights/ Research Highlight In the Arctic, unmanned aircraft systems (UAS) and tethered balloon systems (TBS) can make crucial atmospheric measurements to provide a unique perspective on an environment particularly vulnerable to climate change. To enable research on processes important to climate change in the Arctic-those involving aerosol particles,

  20. Platform for Pre-Symptomatic Detection of Citrus Disease

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Platform for Pre-Symptomatic Detection of Citrus Disease February 18, 2016 Request for Proposal Los Alamos National Security, LLC (LANS) is the manager and operator of Los Alamos National Laboratory (Los Alamos) for the U.S. Department of Energy National Nuclear Security Administration under contract DE-AC52-06NA25396. Los Alamos is a mission- centric Federally Funded Research and Development Center focused on solving critical national security challenges through science and engineering for both

  1. Development of a Very Dense Liquid Cooled Compute Platform

    SciTech Connect (OSTI)

    Hughes, Phillip N.; Lipp, Robert J.

    2013-12-10

    The objective of this project was to design and develop a prototype very energy efficient high density compute platform with 100% pumped refrigerant liquid cooling using commodity components and high volume manufacturing techniques. Testing at SLAC has indicated that we achieved a DCIE of 0.93 against our original goal of 0.85. This number includes both cooling and power supply and was achieved employing some of the highest wattage processors available.

  2. An Extensible Sensing and Control Platform for Building Energy Management

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Anthony Rowe Assistant Research Professor ECE Department Carnegie Mellon University An Extensible Sensing and Control Platform for Building Energy Management DOE Award DE-EE0006353 Mario Bergés Assistant Professor CEE Department Carnegie Mellon University Chris Martin Senior Manager Bosch Research and Technology Center Pittsburgh Partners The Team Anthony Rowe ECE - CMU Mario Bergés CEE - CMU Chris Martin Bosch Patrick Lazik ECE Max Buevich ECE Emre Kara CEE Jingkun Gao CEE Sensor Andrew *

  3. LANL researchers develop platform to study subsurface reservoir conditions

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Subsurface reservoir conditions LANL researchers develop platform to study subsurface reservoir conditions This increasing demand for energy around the globe requires a better understanding of subsurface energy resources and their associated environmental issues. March 7, 2016 Shown are time lapse images of supercritical CO2 displacing water in a fracture etched into a shale micromodel. The white, blue and gray colors represent supercritical CO2, water and shale, respectively. Shown are time

  4. Volttron: distributed sensing and controls platform for buildings

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    VOLTTRON: Distributed Sensing and Controls Platform for Buildings Innovation VOLTTRON and Grid Integration Srinivas Katipamula Pacific Northwest National Laboratory August 11, 2015 Energy Exchange: Federal Sustainability for the Next Decade This project was funded by the U.S. Department of Energy's Building Technologies Office and was managed by Joseph Hagerman. Acknowledgements Energy Exchange: Federal Sustainability for the Next Decade Presentation Outline Current State of Building Operations

  5. National Bioenergy Center Sugar Platform Integration Project: Quarterly Update #10, January-March 2006

    SciTech Connect (OSTI)

    Not Available

    2006-04-01

    Volume 10 of a quarterly newsletter that describes the activities of the National Bioenergy Center's Sugar Platform Integration Project.

  6. National Bioenergy Center Sugar Platform Integration Project: Quarterly Update #12, July-September 2006

    SciTech Connect (OSTI)

    Schell, D.

    2006-10-01

    Volume 12 of a quarterly newsletter that describes the activities of the National Bioenergy Center's Sugar Platform Integration Project.

  7. AutoGrid - Turning Big Data Into Power with the Energy Data Platform and Apps

    SciTech Connect (OSTI)

    Narayan, Amit; Dresselhuys, Eric; Kulp, Yann; Buseman, Greg; Piette, Mary Ann; Tang, Andrew; Dailey, Karla; Knudsen, Chris

    2014-03-25

    AutoGrid personnel discuss how they are turning big data into power with the energy data platform and apps.

  8. Lightweight Integrated Optical Sensor for Atmospheric Measurements on Mobile Platforms

    SciTech Connect (OSTI)

    Parameswaran, Krishnan R.

    2013-12-02

    The goal of the Phase I program was to develop a novel open path sensor platform technology based on integration of semiconductor waveguides with efficient optoelectronic components on a monolithic platform. The successful Phase I effort resulted in demonstration of a novel optical resonator structure based on semiconductor high contrast gratings (HCGs) that will enable implementation of an ultra-compact, low-power gas sensor suitable for use on mobile platforms. Extensive numerical modeling was performed to design a device optimized for measuring CO2 at a wavelength for which a laser was available for proof of concept. Devices were fabricated and tested to match the target wavelength, angle, and operating temperature. This demonstration is the first implementation of HCGs at the wavelengths of interest and shows the flexibility of the proposed architecture for gas sensing applications. The measured cavity Q was lower than anticipated due to fabrication process challenges. The PSI and UC Berkeley team has identified solutions to these challenges and will produce optimized devices in a Phase II program where a prototype sensor will be fabricated and tested.

  9. REopt: A Platform for Energy System Integration and Optimization: Preprint

    SciTech Connect (OSTI)

    Simpkins, T.; Cutler, D.; Anderson, K.; Olis, D.; Elgqvist, E.; Callahan, M.; Walker, A.

    2014-08-01

    REopt is NREL's energy planning platform offering concurrent, multi-technology integration and optimization capabilities to help clients meet their cost savings and energy performance goals. The REopt platform provides techno-economic decision-support analysis throughout the energy planning process, from agency-level screening and macro planning to project development to energy asset operation. REopt employs an integrated approach to optimizing a site?s energy costs by considering electricity and thermal consumption, resource availability, complex tariff structures including time-of-use, demand and sell-back rates, incentives, net-metering, and interconnection limits. Formulated as a mixed integer linear program, REopt recommends an optimally-sized mix of conventional and renewable energy, and energy storage technologies; estimates the net present value associated with implementing those technologies; and provides the cost-optimal dispatch strategy for operating them at maximum economic efficiency. The REopt platform can be customized to address a variety of energy optimization scenarios including policy, microgrid, and operational energy applications. This paper presents the REopt techno-economic model along with two examples of recently completed analysis projects.

  10. D&D Knowledge Management Information Tool

    Office of Environmental Management (EM)

    Directory Web Conference D&D Knowledge Management Information Tool www.dndkm.org Himanshu Upadhyay Research Scientist June 27, 2012 D&D KM-IT WWW.DNDKM.ORG A web-based knowledge ...

  11. A Novel Antibody Engineering Platform to Improve Antibody Stability -

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Innovation Portal A Novel Antibody Engineering Platform to Improve Antibody Stability Argonne National Laboratory Contact ANL About This Technology Fig. 1: Ribbon diagram of a stabilized antibody fragment (scFv) that binds <em>the B. anthracis</em> protein BclA.&nbsp; The stabilizing amino acid modifications are depicted as blue spheres.&nbsp; Fig. 1: Ribbon diagram of a stabilized antibody fragment (scFv) that binds the B. anthracis protein BclA. The stabilizing

  12. A robust platform cooled by superconducting electronic refrigerators

    SciTech Connect (OSTI)

    Nguyen, H. Q.; Meschke, M.; Pekola, J. P.

    2015-01-05

    A biased tunnel junction between a superconductor and a normal metal can cool the latter electrode. Based on a recently developed cooler with high power and superior performance, we have integrated it with a dielectric silicon nitride membrane, and cooled phonons from 305?mK down to 200?mK. Without perforation and covered under a thin alumina layer, the membrane is rigorously transformed into a cooling platform that is robust and versatile for multiple practical purposes. We discussed our results and possibilities to further improve the device.

  13. The power grid of the future is a platform that

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    power grid of the future is a platform that delivers reliable, affordable, and clean electricity to American consumers where they want it, when they want it, and how they want it. To jump start the modernization of our nation's aging energy infrastructure, the American Recovery and Reinvestment Act invested $4.5 billion in the electric sector -matched by private funding to reach a total of about $9.5 billion- so that Americans could start experiencing the benefits of the future grid sooner. Over

  14. The Draugen platform and subsea structures, installation and foundation aspects

    SciTech Connect (OSTI)

    Alm, T.; Bye, A.; Sandvik, K.; Egeland, S.

    1995-12-01

    Installation data from the Draugen GBS and subsea structures have been processed and analyzed in order to verify the design assumptions with regards to soil reactions. These results have shown that penetration of concrete skirts and piles into the very hard clay layer, typically found at the Haltenbanken area is feasible. The resistances may be predicted with reasonable accuracy using conventional methods and average soil strength values as obtained by traditional soil testing. This paper reveals and comments the installation data both for the gravity platform and the piles for the different subsea structures and provides and updated basis for foundation design of similar structures in the area.

  15. An integrated security framework for GOSS power grid analytics platform

    SciTech Connect (OSTI)

    Gibson, Tara D.; Ciraci, Selim; Sharma, Poorva; Allwardt, Craig H.; Rice, Mark J.; Akyol, Bora A.

    2014-06-23

    In power grid operations, security is an essential component for any middleware platform. Security protects data against unwanted access as well as cyber attacks. GridOpticsTM Software System (GOSS) is an open source power grid analytics platform that facilitates ease of access between applications and data sources and promotes development of advanced analytical applications. GOSS contains an API that abstracts many of the difficulties in connecting to various heterogeneous data sources. A number of applications and data sources have already been implemented to demonstrate functionality and ease of use. A security framework has been implemented which leverages widely accepted, robust JavaTM security tools in a way such that they can be interchanged as needed. This framework supports the complex fine-grained, access control rules identified for the diverse data sources already in GOSS. Performance and reliability are also important considerations in any power grid architecture. An evaluation is done to determine the overhead cost caused by security within GOSS and ensure minimal impact to performance.

  16. Horizontally scaling dChache SRM with the Terracotta platform

    SciTech Connect (OSTI)

    Perelmutov, T.; Crawford, M.; Moibenko, A.; Oleynik, G.; /Fermilab

    2011-01-01

    The dCache disk caching file system has been chosen by a majority of LHC experiments Tier 1 centers for their data storage needs. It is also deployed at many Tier 2 centers. The Storage Resource Manager (SRM) is a standardized grid storage interface and a single point of remote entry into dCache, and hence is a critical component. SRM must scale to increasing transaction rates and remain resilient against changing usage patterns. The initial implementation of the SRM service in dCache suffered from an inability to support clustered deployment, and its performance was limited by the hardware of a single node. Using the Terracotta platform, we added the ability to horizontally scale the dCache SRM service to run on multiple nodes in a cluster configuration, coupled with network load balancing. This gives site administrators the ability to increase the performance and reliability of SRM service to face the ever-increasing requirements of LHC data handling. In this paper we will describe the previous limitations of the architecture SRM server and how the Terracotta platform allowed us to readily convert single node service into a highly scalable clustered application.

  17. Centrifugal microfluidic platform for ultrasensitive detection of botulinum toxin

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Koh, Chung -Yan; Schaff, Ulrich Y.; Sandstone Diagnostics, Livermore, CA; Piccini, Matthew E.; Cepheid, Sunnyvale, CA; Stanker, Larry H.; Cheng, Luisa W.; Ravichandran, Easwaran; Singh, Bal -Ram; Sommer, Greg J.; et al

    2014-12-18

    In this study, we present an innovative centrifugal microfluidic immunoassay platform (SpinDx) to address the urgent biodefense and public health need for ultrasensitive point-of-care/incident detection of botulinum toxin. The simple, sample-to-answer centrifugal microfluidic immunoassay approach is based on binding of toxins to antibody-laden capture particles followed by sedimentation of the particles through a density-media in a microfluidic disk and quantification by laser-induced fluorescence. A blind, head-to-head comparison study of SpinDx versus the gold-standard mouse bioassay demonstrates 100-fold improvement in sensitivity (limit of detection = 0.09 pg/mL), while achieving total sample-to-answer time of <30 min with 2-ΌL required volume of themore » unprocessed sample. We further demonstrate quantification of botulinum toxin in both exogeneous (human blood and serum spiked with toxins) and endogeneous (serum from mice intoxicated via oral, intranasal, and intravenous routes) samples. SpinDx can analyze, without any sample preparation, multiple sample types including whole blood, serum, and food. It is readily expandable to additional analytes as the assay reagents (i.e., the capture beads and detection antibodies) are disconnected from the disk architecture and the reader, facilitating rapid development of new assays. SpinDx can also serve as a general-purpose immunoassay platform applicable to diagnosis of other conditions and diseases.« less

  18. Data structures and apparatuses for representing knowledge

    DOE Patents [OSTI]

    Hohimer, Ryan E; Thomson, Judi R; Harvey, William J; Paulson, Patrick R; Whiting, Mark A; Tratz, Stephen C; Chappell, Alan R; Butner, Robert S

    2014-02-18

    Data structures and apparatuses to represent knowledge are disclosed. The processes can comprise labeling elements in a knowledge signature according to concepts in an ontology and populating the elements with confidence values. The data structures can comprise knowledge signatures stored on computer-readable media. The knowledge signatures comprise a matrix structure having elements labeled according to concepts in an ontology, wherein the value of the element represents a confidence that the concept is present in an information space. The apparatus can comprise a knowledge representation unit having at least one ontology stored on a computer-readable medium, at least one data-receiving device, and a processor configured to generate knowledge signatures by comparing datasets obtained by the data-receiving devices to the ontologies.

  19. United Nations Energy Knowledge Network (UN-Energy) | Open Energy...

    Open Energy Info (EERE)

    Energy Knowledge Network (UN-Energy) Jump to: navigation, search Logo: United Nations Energy Knowledge Network (UN-Energy) Name: United Nations Energy Knowledge Network (UN-Energy)...

  20. World Bank-Climate Change Knowledge Portal | Open Energy Information

    Open Energy Info (EERE)

    Climate Change Knowledge Portal Jump to: navigation, search Logo: World Bank-Climate Change Knowledge Portal Name World Bank-Climate Change Knowledge Portal AgencyCompany...

  1. An Insulating Glass Knowledge Base

    SciTech Connect (OSTI)

    Michael L. Doll; Gerald Hendrickson; Gerard Lagos; Russell Pylkki; Chris Christensen; Charlie Cureija

    2005-08-01

    This report will discuss issues relevant to Insulating Glass (IG) durability performance by presenting the observations and developed conclusions in a logical sequential format. This concluding effort discusses Phase II activities and focuses on beginning to quantifying IG durability issues while continuing the approach presented in the Phase I activities (Appendix 1) which discuss a qualitative assessment of durability issues. Phase II developed a focus around two specific IG design classes previously presented in Phase I of this project. The typical box spacer and thermoplastic spacer design including their Failure Modes and Effect Analysis (FMEA) and Fault Tree diagrams were chosen to address two currently used IG design options with varying components and failure modes. The system failures occur due to failures of components or their interfaces. Efforts to begin quantifying the durability issues focused on the development and delivery of an included computer based IG durability simulation program. The focus/effort to deliver the foundation for a comprehensive IG durability simulation tool is necessary to address advancements needed to meet current and future building envelope energy performance goals. This need is based upon the current lack of IG field failure data and the lengthy field observation time necessary for this data collection. Ultimately, the simulation program is intended to be used by designers throughout the current and future industry supply chain. Its use is intended to advance IG durability as expectations grow around energy conservation and with the growth of embedded technologies as required to meet energy needs. In addition the tool has the immediate benefit of providing insight for research and improvement prioritization. Included in the simulation model presentation are elements and/or methods to address IG materials, design, process, quality, induced stress (environmental and other factors), validation, etc. In addition, acquired data is presented in support of project and model assumptions. Finally, current and suggested testing protocol and procedure for future model validation and IG physical testing are discussed.

  2. OTEC Cold Water Pipe-Platform Sub-System Dynamic Interaction Validation

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (OPPSDIV) | Department of Energy OTEC Cold Water Pipe-Platform Sub-System Dynamic Interaction Validation (OPPSDIV) OTEC Cold Water Pipe-Platform Sub-System Dynamic Interaction Validation (OPPSDIV) OTEC Cold Water Pipe-Platform Sub-System Dynamic Interaction Validation (OPPSDIV) Office presentation icon 37_otec_lmco_ascari.ppt More Documents & Publications CX-004741: Categorical Exclusion Determination OTEC resource assessment Water Power Program Peer Review Meeting Agenda

  3. Evaluation of the Tellabs 1150 GPON multiservice access platform.

    SciTech Connect (OSTI)

    Brenkosh, Joseph Peter; Wolf, Jimmie V.

    2014-11-01

    For over two years, Sandia National Laboratories has been using a Gigabit Passive Optical Network (GPON) access layer for selected networks. The GPON equipment includes the Tellabs 1150 Multiservice Access Platform (MSAP) Optical Line Terminal (OLT), the Tellabs ONT709 and ONT709GP Optical Network Terminals (ONTs), and the Panorama PON Network Manager. In late 2013, the Tellabs equipment was updated to Software Release FP27.1_015130. Because a new software release has the potential to affect performance and functionality, it needed to be thoroughly tested. This report documents that testing. It also provides a comparison between the current release and the previous Software Release FP25.5.1_013274 that was being used.

  4. Hazard Analysis for the Pretreatment Engineering Platform (PEP)

    SciTech Connect (OSTI)

    Sullivan, Robin S.; Geeting, John GH; Lawrence, Wesley E.; Young, Jonathan

    2008-07-10

    The Pretreatment Engineering Platform (PEP) is designed to perform a demonstration on an engineering scale to confirm the Hanford Waste Treatment Plant Pretreatment Facility (PTF) leaching and filtration process equipment design and sludge treatment process. The system will use scaled prototypic equipment to demonstrate sludge water wash, caustic leaching, oxidative leaching, and filtration. Unit operations to be tested include pumping, solids washing, chemical reagent addition and blending, heating, cooling, leaching, filtration, and filter cleaning. In addition, the PEP will evaluate potential design changes to the ultrafiltration process system equipment to potentially enhance leaching and filtration performance as well as overall pretreatment throughput. The skid-mounted system will be installed and operated in the Processing Development Laboratory-West at Pacific Northwest National Laboratory (PNNL) in Richland, Washington.

  5. Pretreatment Engineering Platform Phase 1 Final Test Report

    SciTech Connect (OSTI)

    Kurath, Dean E.; Hanson, Brady D.; Minette, Michael J.; Baldwin, David L.; Rapko, Brian M.; Mahoney, Lenna A.; Schonewill, Philip P.; Daniel, Richard C.; Eslinger, Paul W.; Huckaby, James L.; Billing, Justin M.; Sundar, Parameshwaran S.; Josephson, Gary B.; Toth, James J.; Yokuda, Satoru T.; Baer, Ellen BK; Barnes, Steven M.; Golovich, Elizabeth C.; Rassat, Scot D.; Brown, Christopher F.; Geeting, John GH; Sevigny, Gary J.; Casella, Amanda J.; Bontha, Jagannadha R.; Aaberg, Rosanne L.; Aker, Pamela M.; Guzman-Leong, Consuelo E.; Kimura, Marcia L.; Sundaram, S. K.; Pires, Richard P.; Wells, Beric E.; Bredt, Ofelia P.

    2009-12-23

    Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project, Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to conduct testing to demonstrate the performance of the WTP Pretreatment Facility (PTF) leaching and ultrafiltration processes at an engineering-scale. In addition to the demonstration, the testing was to address specific technical issues identified in Issue Response Plan for Implementation of External Flowsheet Review Team (EFRT) Recommendations - M12, Undemonstrated Leaching Processes.( ) Testing was conducted in a 1/4.5-scale mock-up of the PTF ultrafiltration system, the Pretreatment Engineering Platform (PEP). Parallel laboratory testing was conducted in various PNNL laboratories to allow direct comparison of process performance at an engineering-scale and a laboratory-scale. This report presents and discusses the results of those tests.

  6. Vertically Aligned Carbon Nanofiber Based Biosensor Platform for Glucose Sensor

    SciTech Connect (OSTI)

    Mamun, Khandaker Abdullah Al; Tulip, Fahmida S; Macarthur, Kimberly C; McFarlane, Nicole M; Islam, Syed K

    2014-01-01

    Vertically aligned carbon nanofibers (VACNFs) have recently become an important tool for biosensor design. Carbon nanofibers (CNF) have excellent conductive and structural properties with many irregularities and defect sites in addition to exposed carboxyl groups throughout their surfaces. These properties allow a better immobilization matrix compared to carbon nanotubes and offer better resolution when compared with the FET-based biosensors. VACNFs can be deterministically grown on silicon substrates allowing optimization of the structures for various biosensor applications. Two VACNF electrode architectures have been employed in this study and a comparison of their performances has been made in terms of sensitivity, sensing limitations, dynamic range, and response time. The usage of VACNF platform as a glucose sensor has been verified in this study by selecting an optimum architecture based on the VACNF forest density. Read More: http://www.worldscientific.com/doi/abs/10.1142/S0129156414500062

  7. Quantitative Comparison of the Responses of Three Floating Platforms

    SciTech Connect (OSTI)

    Jonkman, J.; Matha, D.

    2010-03-01

    This report presents a comprehensive dynamic-response analysis of three offshore floating wind turbine concepts. Models were composed of one 5-MW turbine supported on land and three 5-MW turbines located offshore on a tension leg platform, a spar buoy, and a barge. A loads and stability analysis adhering to the procedures of international design standards was performed for each model using the fully coupled time-domain aero-hydro-servo-elastic design code FAST with AeroDyn and HydroDyn. The concepts are compared based on the calculated ultimate loads, fatigue loads, and instabilities. The results of this analysis will help resolve the fundamental design trade-offs between the floating-system concepts.

  8. Nanoporous Gold as a Platform for a Building Block Catalyst

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wittstock, Arne; Wichmann, Andre; Baeumer, Marcus

    2012-09-25

    The porous bulk materials are of great interest in catalysis because they can be employed in heterogeneous gas and liquid phase catalysis, electrocatalysis, and in electrocatalytic sensing. Nanoporous gold gained considerable attraction in this context because it is the prime example of a corrosion-derived nanoporous bulk metal. Moreover, the material was shown to be a very active and selective Au type catalyst for a variety of oxidation reactions. In leveraging the functionalization of the surface of the material with various additives, its catalytic applications can be extended and tuned. In this review, we will summarize recent developments in using nanoporousmore » gold as the platform for the development of high performance catalytic materials by adding metals, metal oxides, and molecular functionalities as building blocks.« less

  9. MeDICi: An Open Platform for Sensor Integration

    SciTech Connect (OSTI)

    Wynne, Adam S.; Gorton, Ian; Chase, Jared M.; Stephan, Eric G.

    2009-09-04

    MeDICi (Middleware for Data Intensive Computing) is a platform for developing high performance, distributed streaming analytic and scientific applications. Developed at Pacific Northwest National Laboratory (PNNL), MeDICi has been released under an open source license and is based on enterprise-proven middleware technologies including a widely used Enterprise Service Bus (ESB), the standard Business Process Execution Language (BPEL), and open source message brokers. Wherever possible, we have built on existing open source, standards-based systems and integrated them into a coherent whole by creating simplified graphical programming tools such as a Workflow Designer and an easy to use and well-documented integration API. This software development approach allows us to: avoid re-creating complex service integration and orchestration systems, reap the benefits of continual improvements to the technology base, and focus on creating tools and APIs which allow for the creation of re-usable component-based software components applications and workflows. These aspects have facilitated rapid adoption of the platform within PNNL for demonstration and operational applications. In fact, MeDICi has been used for a wide range of integration projects including two sensor integration applications described later on in this paper. The remainder of this article white paper is organized as follows: Section 2 provides a high-level description of the MeDICi architecture. In Section 3, the open aspects of the API and tool development are highlighted. Section 4 explains system readiness by presenting relevant demonstrations and deployments. Finally documentation and licensing details are provided in Section 5

  10. P417755_IndirectDirectDrivePlatforms_NUG14_v8

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Why Implosions? Direct Drive Platforms Cryogenic Targets Nuclear Physics at the NIF Symmetry capsules or "Symcaps" * Identical to ignition capsules except they do not...

  11. LEDSGP/about/Latin America and Caribbean Regional Platform/LAC...

    Open Energy Info (EERE)

    and Caribbean Regional Platform Workshop 12-14 November 2012 Alajuela, Costa Rica, INCAE Business School The workshop is an initiative of the LEDS Global Partnership (http:...

  12. A MEMS platform for in situ, real-time monitoring of electrochemically...

    Office of Scientific and Technical Information (OSTI)

    Title: A MEMS platform for in situ, real-time monitoring of electrochemically induced mechanical changes in lithium-ion battery electrodes Authors: Pomerantseva, Ekaterina ; Jung, ...

  13. Microfluidic Molecular Assay Platform for the Detection of miRNAs...

    Office of Scientific and Technical Information (OSTI)

    Article: Microfluidic Molecular Assay Platform for the Detection of miRNAs, mRNAs, Proteins, and Post-translational Modifications at Single-cell Resolution. Citation Details...

  14. Bioenergy Knowledge Discovery Framework (KDF) Fact Sheet

    SciTech Connect (OSTI)

    2013-07-29

    The Bioenergy Knowledge Discovery Framework (KDF) is an online collaboration and geospatial analysis tool that allows researchers, policymakers, and investors to explore and engage the latest bioenergy research. This publication describes how the KDF harnesses Web 2.0 and social networking technologies to build a collective knowledge system that facilitates collaborative production, integration, and analysis of bioenergy-related information.

  15. Financial Management System (FMS) Help & Knowledge Base

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Financial Management System (FMS) Help & Knowledge Base

  16. Creating a Discovery Platform for Confined-Space Chemistry and Materials: Metal-Organic Frameworks.

    SciTech Connect (OSTI)

    Allendorf, Mark D.; Greathouse, Jeffery A.; Simmons, Blake

    2008-09-01

    Metal organic frameworks (MOF) are a recently discovered class of nanoporous, defect-free crystalline materials that enable rational design and exploration of porous materials at the molecular level. MOFs have tunable monolithic pore sizes and cavity environments due to their crystalline nature, yielding properties exceeding those of most other porous materials. These include: the lowest known density (91% free space); highest surface area; tunable photoluminescence; selective molecular adsorption; and methane sorption rivaling gas cylinders. These properties are achieved by coupling inorganic metal complexes such as ZnO4 with tunable organic ligands that serve as struts, allowing facile manipulation of pore size and surface area through reactant selection. MOFs thus provide a discovery platform for generating both new understanding of chemistry in confined spaces and novel sensors and devices based on their unique properties. At the outset of this project in FY06, virtually nothing was known about how to couple MOFs to substrates and the science of MOF properties and how to tune them was in its infancy. An integrated approach was needed to establish the required knowledge base for nanoscale design and develop methodologies integrate MOFs with other materials. This report summarizes the key accomplishments of this project, which include creation of a new class of radiation detection materials based on MOFs, luminescent MOFs for chemical detection, use of MOFs as templates to create nanoparticles of hydrogen storage materials, MOF coatings for stress-based chemical detection using microcantilevers, and %22flexible%22 force fields that account for structural changes in MOFs that occur upon molecular adsorption/desorption. Eight journal articles, twenty presentations at scientific conferences, and two patent applications resulted from the work. The project created a basis for continuing development of MOFs for many Sandia applications and succeeded in securing %242.75 M in funding from outside agencies to continue the research. 3

  17. Ocean Thermal Energy Conversion moored pipe/mobile platform design study

    SciTech Connect (OSTI)

    Bullock, H.O.; McNatt, T.R.; Ross, J.M.; Stambaugh, K.A.; Watts, J.L.

    1982-07-30

    The Ocean Thermal Energy Conversion (OTEC) Moored Pipe/Mobile Platform (MP-Squared) Design Study was carried out to investigate an innovative approach to the moored floating OTEC plant. In the past, a number of concepts have been examined by NOAA for floating OTEC plants. These concepts have considered various configurations for platforms, cold water pipes and mooring systems. In most cases the cold water pipe (CWP) was permanently attached to the platform and the platform was permanently moored on station. Even though CWP concepts incorporating articulated joints or flexible pipes were used, the CWP stresses induced by platform motion were frequently excessive and beyond the design limits of the CWP. This was especially true in the survival (100-year storm) case. It may be feasible that the concept of a permanently moored CWP attached through a flexible transition CWP to the platform could reduce the degree of technical risk by de-coupling the CWP from the motions of the platform. In addition, if the platform is capable of disconnecting from the CWP during survival conditions, even less technical risk may be inherent in the OTEC system. The MP-Squared Design Study was an engineering evaluation of the concepts described above. The effort has been carried through to the conceptual design level, and culminated in model tests in an experimental wave basin.

  18. Selecting Observation Platforms for Optimized Anomaly Detectability under Unreliable Partial Observations

    SciTech Connect (OSTI)

    Wen-Chiao Lin; Humberto E. Garcia; Tae-Sic Yoo

    2011-06-01

    Diagnosers for keeping track on the occurrences of special events in the framework of unreliable partially observed discrete-event dynamical systems were developed in previous work. This paper considers observation platforms consisting of sensors that provide partial and unreliable observations and of diagnosers that analyze them. Diagnosers in observation platforms typically perform better as sensors providing the observations become more costly or increase in number. This paper proposes a methodology for finding an observation platform that achieves an optimal balance between cost and performance, while satisfying given observability requirements and constraints. Since this problem is generally computational hard in the framework considered, an observation platform optimization algorithm is utilized that uses two greedy heuristics, one myopic and another based on projected performances. These heuristics are sequentially executed in order to find best observation platforms. The developed algorithm is then applied to an observation platform optimization problem for a multi-unit-operation system. Results show that improved observation platforms can be found that may significantly reduce the observation platform cost but still yield acceptable performance for correctly inferring the occurrences of special events.

  19. Transaction-based building controls framework, Volume 2: Platform descriptive model and requirements

    SciTech Connect (OSTI)

    Akyol, Bora A.; Haack, Jereme N.; Carpenter, Brandon J.; Katipamula, Srinivas; Lutes, Robert G.; Hernandez, George

    2015-07-31

    Transaction-based Building Controls (TBC) offer a control systems platform that provides an agent execution environment that meets the growing requirements for security, resource utilization, and reliability. This report outlines the requirements for a platform to meet these needs and describes an illustrative/exemplary implementation.

  20. Offshore Energy Knowledge Exchange Workshop Report

    SciTech Connect (OSTI)

    none,

    2012-04-12

    A report detailing the presentations and topics discussed at the Offshore Energy Knowledge Exchange Workshop, an event designed to bring together offshore energy industry representatives to share information, best practices, and lessons learned.

  1. PaR-PaR Laboratory Automation Platform

    SciTech Connect (OSTI)

    Linshiz, G; Stawski, N; Poust, S; Bi, CH; Keasling, JD; Hilson, NJ

    2013-05-01

    Labor-intensive multistep biological tasks, such as the construction and cloning of DNA molecules, are prime candidates for laboratory automation. Flexible and biology-friendly operation of robotic equipment is key to its successful integration in biological laboratories, and the efforts required to operate a robot must be much smaller than the alternative manual lab work. To achieve these goals, a simple high-level biology-friendly robot programming language is needed. We have developed and experimentally validated such a language: Programming a Robot (PaR-PaR). The syntax and compiler for the language are based on computer science principles and a deep understanding of biological workflows. PaR-PaR allows researchers to use liquid-handling robots effectively, enabling experiments that would not have been considered previously. After minimal training, a biologist can independently write complicated protocols for a robot within an hour. Adoption of PaR-PaR as a standard cross-platform language would enable hand-written or software-generated robotic protocols to be shared across laboratories.

  2. Big Data Platforms as a Service: Challenges and Approach

    SciTech Connect (OSTI)

    Horey, James L; Gunasekaran, Raghul; Lim, Seung-Hwan; Begoli, Edmon; Nutaro, James J

    2012-01-01

    Infrastructure-as-a-Service has revolutionized the manner in which users commission computing infrastructure. Coupled with Big Data platforms (Hadoop, Cassandra), IaaS has democratized the ability to store and process massive datasets. For users that need to customize or create new Big Data stacks, however, readily available solutions do not yet exist. Users must first acquire the necessary cloud computing infrastructure, and manually install the prerequisite software. For complex distributed services this can be a daunting challenge. To address this issue, we argue that distributed services should be viewed as a single application consisting of virtual machines. Users should no longer be concerned about individual machines or their internal organization. To illustrate this concept, we introduce Cloud-Get, a distributed package manager that enables the simple installation of distributed services in a cloud computing environment. Cloud-Get enables users to instantiate and modify distributed services, including Big Data services, using simple commands. Cloud-Get also simplifies creating new distributed services via standardized package definitions.

  3. Multiphase pumps and flow meters avoid platform construction

    SciTech Connect (OSTI)

    Elde, J.

    1999-02-01

    One of the newest wrinkles in efficiency in BP`s Eastern Trough Area Project (ETAP) is the system for moving multiphase oil, water and gas fluids from the Machar satellite field to the Marnock Central Processing Facility (CPF). Using water-turbine-driven multiphase pumps and multiphase flow meters, the system moves fluid with no need for a production platform. In addition, BP has designed the installation so it reduces and controls water coning, thereby increasing recoverable reserves. Both subsea multiphase booster stations (SMUBS) and meters grew out of extensive development work and experience at Framo Engineering AS (Framo) in multiphase meters and multiphase pump systems for subsea installation. Multiphase meter development began in 1990 and the first subsea multiphase meters were installed in the East Spar Project in Australia in 1996. By September 1998, the meters had been operating successfully for more than 1 year. A single multiphase meter installed in Marathon`s West Brae Project has also successfully operated for more than 1 year. Subsea meters for ETAP were installed and began operating in July 1998.

  4. Knowledge Acquisition Ubiquitous Agent Infrastructure (KAUAI)

    Energy Science and Technology Software Center (OSTI)

    2009-09-15

    Mobile agents are autonomous software programs that can move from one host to another during the course of execution. The KAUAI computer code is a middleware that supports the rapid development and deployment of mobile agent based applications. It is built on the J2ME (CLDC) technology. KAUAI handles the instantiation, execution, transportation, and disposal of mobile agents. KAUAI masks the underlying hardware and communication details from application developers and provides flexible functionality for distributed computing.more » KAUAI supports software development in systems that involve a large number of heterogeneous computing platforms ranging from workstations to handheld devices.« less

  5. Growth, microstructure, and luminescent

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    In and Ga adatoms, being more mobile, preferentially attach to steps. Step-flow growth prop- agates the InGa rich superstep and results in the creation of long continuous...

  6. FGF growth factor analogs

    DOE Patents [OSTI]

    Zamora, Paul O.; Pena, Louis A.; Lin, Xinhua; Takahashi, Kazuyuki

    2012-07-24

    The present invention provides a fibroblast growth factor heparin-binding analog of the formula: ##STR00001## where R.sub.1, R.sub.2, R.sub.3, R.sub.4, R.sub.5, X, Y and Z are as defined, pharmaceutical compositions, coating compositions and medical devices including the fibroblast growth factor heparin-binding analog of the foregoing formula, and methods and uses thereof.

  7. Smart Cities - Smart Growth

    Energy Savers [EERE]

    Smart Cities - Smart Growth The United States Secretaries of Commerce will co-lead a Business Development Mission to China from April 12-17, 2015. This mission will promote U.S. clean technology products and services in the areas of green building/construction, energy efficiency, carbon capture, utilization and storage (CCUS) and environmental technologies in support of the Smart Cities-Smart Growth theme. On November 12, President Obama and President Xi jointly announced the two countries'

  8. Isopropanol production with engineered Cupriavidus necator as bioproduction platform

    SciTech Connect (OSTI)

    Grousseau, E; Lu, JN; Gorret, N; Guillouet, SE; Sinskey, AJ

    2014-03-07

    Alleviating our society's dependence on petroleum-based chemicals has been highly emphasized due to fossil fuel shortages and increasing greenhouse gas emissions. Isopropanol is a molecule of high potential to replace some petroleum-based chemicals, which can be produced through biological platforms from renewable waste carbon streams such as carbohydrates, fatty acids, or CO2. In this study, for the first time, the heterologous expression of engineered isopropanol pathways were evaluated in a Cupriavidus necator strain Re2133, which was incapable of producing poly-3-hydroxybutyrate [P(3HB)]. These synthetic production pathways were rationally designed through codon optimization, gene placement, and gene dosage in order to efficiently divert carbon flow from P(3HB) precursors toward isopropanol. Among the constructed pathways, Re2133/pEG7c overexpressing native C. necator genes encoding a beta-ketothiolase, a CoA-transferase, and codon-optimized Clostridium genes encoding an acetoacetate decarboxylase and an alcohol dehydrogenase produced up to 3.44 g l(-1) isopropanol in batch culture, from fructose as a sole carbon source, with only 0.82 g l(-1) of biomass. The intrinsic performance of this strain (maximum specific production rate 0.093 g g(-1) h(-1), yield 0.32 Cmole Cmole(-1)) corresponded to more than 60 % of the respective theoretical performance. Moreover, the overall isopropanol production yield (0.24 Cmole Cmole(-1)) and the overall specific productivity (0.044 g g(-1) h(-1)) were higher than the values reported in the literature to date for heterologously engineered isopropanol production strains in batch culture. Strain Re2133/pEG7c presents good potential for scale-up production of isopropanol from various substrates in high cell density cultures.

  9. VOLTTRON™: An Agent Platform for Integrating Electric Vehicles and Smart Grid

    SciTech Connect (OSTI)

    Haack, Jereme N.; Akyol, Bora A.; Tenney, Nathan D.; Carpenter, Brandon J.; Pratt, Richard M.; Carroll, Thomas E.

    2013-12-06

    The VOLTTRON™ platform provides a secure environment for the deployment of intelligent applications in the smart grid. VOLTTRON design is based on the needs of control applications running on small form factor devices, namely security and resource guarantees. Services such as resource discovery, secure agent mobility, and interacting with smart and legacy devices are provided by the platform to ease the development of control applications and accelerate their deployment. VOLTTRON platform has been demonstrated in several different domains that influenced and enhanced its capabilities. This paper will discuss the features of VOLTTRON and highlight its usage to coordinate electric vehicle charging with home energy usage

  10. Knowledge Encapsulation Framework for Collaborative Social Modeling

    SciTech Connect (OSTI)

    Cowell, Andrew J.; Gregory, Michelle L.; Marshall, Eric J.; McGrath, Liam R.

    2009-03-24

    This paper describes the Knowledge Encapsulation Framework (KEF), a suite of tools to enable knowledge inputs (relevant, domain-specific facts) to modeling and simulation projects, as well as other domains that require effective collaborative workspaces for knowledge-based task. This framework can be used to capture evidence (e.g., trusted material such as journal articles and government reports), discover new evidence (covering both trusted and social media), enable discussions surrounding domain-specific topics and provide automatically generated semantic annotations for improved corpus investigation. The current KEF implementation is presented within a wiki environment, providing a simple but powerful collaborative space for team members to review, annotate, discuss and align evidence with their modeling frameworks. The novelty in this approach lies in the combination of automatically tagged and user-vetted resources, which increases user trust in the environment, leading to ease of adoption for the collaborative environment.

  11. SEB Secretariat and Knowledge Manager | Department of Energy

    Energy Savers [EERE]

    SEB Secretariat and Knowledge Manager SEB Secretariat and Knowledge Manager PDF icon SEB Secretariat and Knowledge Manager More Documents & Publications Source Selection Chapter 15 - Contracting by Negotiation OPAM Policy Acquisition Guides

  12. Automated Knowledge Annotation for Dynamic Collaborative Environments

    SciTech Connect (OSTI)

    Cowell, Andrew J.; Gregory, Michelle L.; Marshall, Eric J.; McGrath, Liam R.

    2009-05-19

    This paper describes the Knowledge Encapsulation Framework (KEF), a suite of tools to enable automated knowledge annotation for modeling and simulation projects. This framework can be used to capture evidence (e.g., facts extracted from journal articles and government reports), discover new evidence (from similar peer-reviewed material as well as social media), enable discussions surrounding domain-specific topics and provide automatically generated semantic annotations for improved corpus investigation. The current KEF implementation is presented within a wiki environment, providing a simple but powerful collaborative space for team members to review, annotate, discuss and align evidence with their modeling frameworks.

  13. National Bioenergy Center--Biochemical Platform Integration Project: Quarterly Update, Fall 2010

    SciTech Connect (OSTI)

    Schell, D.

    2010-12-01

    Fall 2010 edition of the National Bioenergy Center's Biochemical Platform Integration Project quarterly newsletter. Issue topics: rapid analysis models for compositional analysis of intermediate process streams; engineered arabinose-fermenting Zymomonas mobilis strain.

  14. Three-dimensional microelectromechanical tilting platform operated by gear-driven racks

    DOE Patents [OSTI]

    Klody, Kelly A.; Habbit, Jr., Robert D.

    2005-11-01

    A microelectromechanical (MEM) tiltable-platform apparatus is disclosed which utilizes a light-reflective platform (i.e. a micromirror) which is supported above a substrate by flexures which can be bent upwards to tilt the platform in any direction over an angle of generally .+-.10 degrees using a gear-driven rack attached to each flexure. Each rack is driven by a rotary microengine (i.e. a micromotor); and an optional thermal actuator can be used in combination with each microengine for initially an initial uplifting of the platform away from the substrate. The MEM apparatus has applications for optical switching (e.g. between a pair of optical fibers) or for optical beam scanning.

  15. File:BOEMRE oil.gas.plant.platform.sta.brbra.map.4.2010.pdf ...

    Open Energy Info (EERE)

    oil.gas.plant.platform.sta.brbra.map.4.2010.pdf Jump to: navigation, search File File history File usage Federal Leases in Pacific Ocean, near Santa Barbara Channel Size of this...

  16. Forensic DNA Standards for Next Generation Sequencing Platforms ( 7th Annual SFAF Meeting, 2012)

    ScienceCinema (OSTI)

    Vallone, Peter [NIST

    2013-03-22

    Peter Vallone on "Forensic DNA Standards for Next Generation Sequencing Platforms" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

  17. File:BOEMRE platforms.leases.longbeach.map.5.2010.pdf | Open...

    Open Energy Info (EERE)

    platforms.leases.longbeach.map.5.2010.pdf Jump to: navigation, search File File history File usage Federal Leases in Pacific Ocean, near Long Beach Size of this preview: 463 599...

  18. File:BOEMRE lease.platforms.santa.barb.map.5.2010.pdf | Open...

    Open Energy Info (EERE)

    lease.platforms.santa.barb.map.5.2010.pdf Jump to: navigation, search File File history File usage Federal Leases in Pacific Ocean, near Santa Maria Basin Size of this preview: 776...

  19. Template:Climate Knowledge Brokers Navigation | Open Energy Informatio...

    Open Energy Info (EERE)

    Climate Knowledge Brokers Navigation Jump to: navigation, search This is the Climate Knowledge Brokers Navigation template. It generates the navigation displayed at the top of all...

  20. New Jersey Institute of Technology Center for Building Knowledge...

    Open Energy Info (EERE)

    Institute of Technology Center for Building Knowledge Jump to: navigation, search Name: New Jersey Institute of Technology Center for Building Knowledge Place: University Heights...

  1. Knowledge Partnership for Measuring Air Pollution and Greenhouse...

    Open Energy Info (EERE)

    Knowledge Partnership for Measuring Air Pollution and Greenhouse Gas Emissions in Asia Jump to: navigation, search Name Knowledge Partnership for Measuring Air Pollution and...

  2. Energy and Interior Departments Host Offshore Energy Knowledge...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Interior Departments Host Offshore Energy Knowledge Exchange Workshop Energy and Interior Departments Host Offshore Energy Knowledge Exchange Workshop May 1, 2012 - 2:52pm ...

  3. A knowledge continuity management program for the energy, infrastructure and knowledge systems center, Sandia National Laboratories.

    SciTech Connect (OSTI)

    Menicucci, David F.

    2006-07-01

    A growing recognition exists in companies worldwide that, when employees leave, they take with them valuable knowledge that is difficult and expensive to recreate. The concern is now particularly acute as the large ''baby boomer'' generation is reaching retirement age. A new field of science, Knowledge Continuity Management (KCM), is designed to capture and catalog the acquired knowledge and wisdom from experience of these employees before they leave. The KCM concept is in the final stages of being adopted by the Energy, Infrastructure, and Knowledge Systems Center and a program is being applied that should produce significant annual cost savings. This report discusses how the Center can use KCM to mitigate knowledge loss from employee departures, including a concise description of a proposed plan tailored to the Center's specific needs and resources.

  4. A New Low-Cost Measurement Platform for Urea Quality Monitoring |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy A New Low-Cost Measurement Platform for Urea Quality Monitoring A New Low-Cost Measurement Platform for Urea Quality Monitoring This technique can use specifications for urea quality to calibrate emission controls and compliance measurements. PDF icon deer08_linden.pdf More Documents & Publications Lithium Ion Electrode Production NDE and QC Considerations Ensuring the Availability and Reliability of Urea Dosing For On-Road and Non-Road List of SBIR / STTR Awardees

  5. Genomics-enabled sensor platform for rapid detection of viruses related to

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    disease outbreak. (Technical Report) | SciTech Connect Genomics-enabled sensor platform for rapid detection of viruses related to disease outbreak. Citation Details In-Document Search Title: Genomics-enabled sensor platform for rapid detection of viruses related to disease outbreak. Bioweapons and emerging infectious diseases pose growing threats to our national security. Both natural disease outbreak and outbreaks due to a bioterrorist attack are a challenge to detect, taking days after the

  6. Genomics-enabled sensor platform for rapid detection of viruses related to

    Office of Scientific and Technical Information (OSTI)

    disease outbreak. (Technical Report) | SciTech Connect SciTech Connect Search Results Technical Report: Genomics-enabled sensor platform for rapid detection of viruses related to disease outbreak. Citation Details In-Document Search Title: Genomics-enabled sensor platform for rapid detection of viruses related to disease outbreak. Bioweapons and emerging infectious diseases pose growing threats to our national security. Both natural disease outbreak and outbreaks due to a bioterrorist attack

  7. Design and Control of a Ship Motion Simulation Platform from an Energy

    Office of Scientific and Technical Information (OSTI)

    Efficiency Perspective (Journal Article) | SciTech Connect Journal Article: Design and Control of a Ship Motion Simulation Platform from an Energy Efficiency Perspective Citation Details In-Document Search Title: Design and Control of a Ship Motion Simulation Platform from an Energy Efficiency Perspective Most hydraulic servo systems are designed with little consideration for energy efficiency. Pumps are selected based upon required peak power demands, valves are chosen primarily for their

  8. A MEMS platform for in situ, real-time monitoring of electrochemically

    Office of Scientific and Technical Information (OSTI)

    induced mechanical changes in lithium-ion battery electrodes (Journal Article) | SciTech Connect A MEMS platform for in situ, real-time monitoring of electrochemically induced mechanical changes in lithium-ion battery electrodes Citation Details In-Document Search Title: A MEMS platform for in situ, real-time monitoring of electrochemically induced mechanical changes in lithium-ion battery electrodes Authors: Pomerantseva, Ekaterina ; Jung, H. ; Gnerlich, Markus ; Gerasopoulos, K ; Ghodssi,

  9. What's New with CINT Discovery Platforms?. (Conference) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    What's New with CINT Discovery Platforms?. Citation Details In-Document Search Title: What's New with CINT Discovery Platforms?. Abstract not provided. Authors: Sullivan, John P Publication Date: 2011-12-01 OSTI Identifier: 1118379 Report Number(s): SAND2011-9207C 481426 DOE Contract Number: AC04-94AL85000 Resource Type: Conference Resource Relation: Conference: 2011 CINT Science Advisory Commitee Meeting held December 8-9, 2011 in Santa Fe, NM.; Related Information: Proposed for presentation at

  10. xLPR v2.0: Framework Overview Landing platform and deterministic model.

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect : Framework Overview Landing platform and deterministic model. Citation Details In-Document Search Title: xLPR v2.0: Framework Overview Landing platform and deterministic model. Abstract not provided. Authors: Dingreville, Remi Philippe Michel ; Mariner, Paul E. ; Sallaberry, Cedric M. Publication Date: 2013-09-01 OSTI Identifier: 1115158 Report Number(s): SAND2013-7743C 477258 DOE Contract Number: AC04-94AL85000 Resource Type: Conference Resource Relation:

  11. Adapting On-Site Electrical Generation Platforms for Producer Gas - Fact

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Sheet, April 2014 | Department of Energy Adapting On-Site Electrical Generation Platforms for Producer Gas - Fact Sheet, April 2014 Adapting On-Site Electrical Generation Platforms for Producer Gas - Fact Sheet, April 2014 The University of Minnesota, Morris, in collaboration with the University of Minnesota Center for Diesel Research, Cummins Power Generation Inc., ALL Power Labs, and Hammel, Green & Abrahamson (HGA), integrated a biomass gasifier and a reciprocating engine generator

  12. Modular OTEC platforms, SKSS designs. Volume I. Executive summary. Final report

    SciTech Connect (OSTI)

    1980-02-29

    One of the possible options for generating electrical energy from ocean thermal gradients requires the use of a floating offshore platform. The platform would contain all OTEC (Ocean Thermal Energy Conversion) systems and power cycle components and consist of the hull, seawater, station-keeping, platform service, and mission support subsystems. It would be stationed at one of the designated OTEC sites, and would transmit the generated electricity to the shore power networks by means of an electrical transmission cable. The objective of the present study is to investigate the station-keeping subsystem (SKSS) requirements and develop preliminary SKSS designs for the two Modular Experiment Plant (MEP) candidates of 10/40 MW/sub e/ capacity for deployment at a specific site. The two MEP hull candidates are a Barge type platform and a Spar shaped hull with external heat exchangers. The specific site assigned for this study is Puerto Rico. The preliminary SKSS designs are developed for both platforms as follows: (1) an 8-leg spread catenary mooring system for the Spar, and (2) a 12-leg spread catenary mooring system for the Barge. Applicability of these designs to larger capacity commercial OTEC platforms is also investigated.

  13. Plant growth promoting rhizobacterium

    DOE Patents [OSTI]

    Doktycz, Mitchel John; Pelletier, Dale A.; Schadt, Christopher Warren; Tuskan, Gerald A.; Weston, David

    2015-08-11

    The present invention is directed to the Pseudomonas fluorescens strain GM30 deposited under ATCC Accession No. PTA-13340, compositions containing the GM30 strain, and methods of using the GM30 strain to enhance plant growth and/or enhance plant resistance to pathogens.

  14. Evaluation of the reliability of a conventional platform installed in South Pass Block 47 of the Mississippi River delta

    SciTech Connect (OSTI)

    Bea, R.G.

    1996-12-31

    In August 1995, the Energy Development Corporation (EDC) installed a conventional drilling and production platform in South Pass Block 47 (SP 47). Due to its proximity to the delta of the Mississippi River, this platform will be subject to the environmental forces developed by hurricanes and movements of the sea floor. This paper summarizes results from probability based study of the reliability characteristics of a conventional platform installed in SP 47. Bases for evaluation of the acceptability of the reliability of the platform are developed. This paper shows how reliability methods can be used to help improve the efficiency of offshore platforms. Application of traditional engineering approaches indicated the need for a mudslide resistant platform. Given that a mudslide resistant platform was required, then the gas reserves could not have been developed.

  15. Patent: Conditioning biomass for microbial growth | DOEpatents

    Office of Scientific and Technical Information (OSTI)

    Conditioning biomass for microbial growth Citation Details Title: Conditioning biomass for microbial growth

  16. The Digital Road to Scientific Knowledge Diffusion

    Office of Scientific and Technical Information (OSTI)

    Digital Road to Scientific Knowledge Diffusion A Faster, Better Way to Scientific Progress? By David E. Wojick, Walter L. Warnick, Bonnie C. Carroll, and June Crowe Introduction With the United States federal government spending over $130 billion annually for research and development, ways to increase the productivity of that research can have a significant return on investment. It is well known that all scientific advancement is based on work that has come before. Isaac Newton expressed this

  17. Knowledge Discovery, Knowledge Management and Enterprise-Wide Information Technology Tools Final Report

    SciTech Connect (OSTI)

    Patton, Robert M; Symons, Christopher T; Gorman, Bryan L; Treadwell, Jim N

    2012-04-01

    A final report on an ORNL task to establish a knowledge discovery and management tool to retrieve and recommend information from existing S&T documents for the Office of Naval Research Global.

  18. Electrochemical Solution Growth: Gallium Nitride Crystal Growth - Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovation Portal Vehicles and Fuels Vehicles and Fuels Building Energy Efficiency Building Energy Efficiency Find More Like This Return to Search Electrochemical Solution Growth: Gallium Nitride Crystal Growth Sandia National Laboratories Contact SNL About This Technology Publications: PDF Document Publication Market Sheet (886 KB) Technology Marketing SummarySandia National Laboratories has developed a disruptive new crystal growth technology, called Electrochemical Solution Growth (ESG).

  19. The shock/shear platform for planar radiation-hydrodynamics experiments on the National Ignition Facility

    SciTech Connect (OSTI)

    Doss, F. W.; Kline, J. L.; Flippo, K. A.; Perry, T. S.; DeVolder, B. G.; Tregillis, I.; Loomis, E. N.; Merritt, E. C.; Murphy, T. J.; Welser-Sherrill, L.; Fincke, J. R.

    2015-04-17

    An indirectly-driven shock tube experiment fielded on the National Ignition Facility (NIF) was used to create a high-energy-density hydrodynamics platform at unprecedented scale. Scaling up a shear-induced mixing experiment previously fielded at OMEGA, the NIF shear platform drives 130 ?m/ns shocks into a CH foam-filled shock tube (~ 60 mg/cc) with interior dimensions of 1.5 mm diameter and 5 mm length. The pulse-shaping capabilities of the NIF are used to extend the drive for >10 ns, and the large interior tube volumes are used to isolate physics-altering edge effects from the region of interest. The scaling of the experiment to the NIF allows for considerable improvement in maximum driving time of hydrodynamics, in fidelity of physics under examination, and in diagnostic clarity. Details of the experimental platform and post-shot simulations used in the analysis of the platform-qualifying data are presented. Hydrodynamic scaling is used to compare shear data from OMEGA with that from NIF, suggesting a possible change in the dimensionality of the instability at late times from one platform to the other.

  20. The shock/shear platform for planar radiation-hydrodynamics experiments on the National Ignition Facility

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Doss, F. W.; Kline, J. L.; Flippo, K. A.; Perry, T. S.; DeVolder, B. G.; Tregillis, I.; Loomis, E. N.; Merritt, E. C.; Murphy, T. J.; Welser-Sherrill, L.; et al

    2015-04-17

    An indirectly-driven shock tube experiment fielded on the National Ignition Facility (NIF) was used to create a high-energy-density hydrodynamics platform at unprecedented scale. Scaling up a shear-induced mixing experiment previously fielded at OMEGA, the NIF shear platform drives 130 Όm/ns shocks into a CH foam-filled shock tube (~ 60 mg/cc) with interior dimensions of 1.5 mm diameter and 5 mm length. The pulse-shaping capabilities of the NIF are used to extend the drive for >10 ns, and the large interior tube volumes are used to isolate physics-altering edge effects from the region of interest. The scaling of the experiment tomore » the NIF allows for considerable improvement in maximum driving time of hydrodynamics, in fidelity of physics under examination, and in diagnostic clarity. Details of the experimental platform and post-shot simulations used in the analysis of the platform-qualifying data are presented. Hydrodynamic scaling is used to compare shear data from OMEGA with that from NIF, suggesting a possible change in the dimensionality of the instability at late times from one platform to the other.« less

  1. Bioenergy Science Center KnowledgeBase

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Syed, M. H.; Karpinets, T. V.; Parang, M.; Leuze, M. R.; Park, B. H.; Hyatt, D.; Brown, S. D.; Moulton, S. Galloway, M.D.; Uberbacher, E. C.

    The challenge of converting cellulosic biomass to sugars is the dominant obstacle to cost effective production of biofuels in s capable of significant enough quantities to displace U. S. consumption of fossil transportation fuels. The BioEnergy Science Center (BESC) tackles this challenge of biomass recalcitrance by closely linking (1) plant research to make cell walls easier to deconstruct, and (2) microbial research to develop multi-talented biocatalysts tailor-made to produce biofuels in a single step. [from the 2011 BESC factsheet] The BioEnergy Science Center (BESC) is a multi-institutional, multidisciplinary research (biological, chemical, physical and computational sciences, mathematics and engineering) organization focused on the fundamental understanding and elimination of biomass recalcitrance. The BESC Knowledgebase and its associated tools is a discovery platform for bioenergy research. It consists of a collection of metadata, data, and computational tools for data analysis, integration, comparison and visualization for plants and microbes in the center.The BESC Knowledgebase (KB) and BESC Laboratory Information Management System (LIMS) enable bioenergy researchers to perform systemic research. [http://bobcat.ornl.gov/besc/index.jsp

  2. Growth in Solar Means Growth in Ohio | Department of Energy

    Office of Environmental Management (EM)

    Growth in Solar Means Growth in Ohio Growth in Solar Means Growth in Ohio October 6, 2010 - 2:26pm Addthis Lorelei Laird Writer, Energy Empowers Editor's Note: Yesterday Secretary Chu announced that solar panels and a solar hot water heater will be added to the White House by the end of next spring. This entry is cross-posted from the Energy Empowers blog and deals with how the continued growth of solar power is not only a boon for industry, but for local economies as well. The solar industry

  3. Cleaning of the ocean floor near offshore platforms in the Gulf coast

    SciTech Connect (OSTI)

    Fang, C.S.; Smith, S.A. Jr.

    1986-03-01

    For decades in offshore drilling, the drill cuttings were separated from the circulating drilling fluid by the shale shaker and hydrocyclone, and discharged to the ocean. The drilling fluid itself was discharged to the ocean intermittently to maintain its required properties during the drilling process. These discharges contain many environmentally undesirable chemicals, such as hydrocarbons chemical additives and heavy metals. As a result, the ocean floor near some of the offshore platforms in the Gulf of Mexico are covered by contaminated sediment. Ocean current is not as effective in washing out the discarded ocean muds as previously believed. An attempt was made to clean some of the offshore platforms in the Gulf of Mexico. The quantity and characteristics of the drilling discharges are estimated the technology used to clean the ocean floor near platforms is described, and advanced treatments for hydrocarbon removal, chemical oxidation and activated carbon adsorption, are discussed. 8 references.

  4. Nanotag-enabled photonic crystal fiber as quantitative surface-enhanced Raman scattering optofluidic platform

    SciTech Connect (OSTI)

    Pinkhasova, Polina; Chen, Hui; Du, Henry; Kanka, Jiri; Mergo, Pawel

    2015-02-16

    Core-shell nanotags that are active in surface-enhanced Raman scattering (SERS) and entrapped with thiocyanate (SCN) label molecules were immobilized in the air channels of suspended-core photonic crystal fiber (PCF) to impart quantitative capacity to SERS-based PCF optofluidic sensing platform. The Raman intensity of Rhodamine 6G increases with concentration, whereas the intensity of SCN remains constant when measured using this platform. The signal from the SCN label can be used as an internal reference to establish calibration for quantitative measurements of analytes of unknown concentrations. The long optical path-length PCF optofluidic platform integrated with SERS-active core-shell nanotags holds significant promise for sensitive quantitative chem/bio measurements with the added benefit of small sampling volume. The dependence of SERS intensity on the nanotag coverage density and PCF length was interpreted based on numerical-analytical simulations.

  5. D&D Toolbox Project - Technology Demonstration of Fixatives Applied to Hot Cell Facilities via Remote Sprayer Platforms

    Office of Environmental Management (EM)

    Demonstration D&D Toolbox - FIU Tech Demo FIU Technology Demonstration - Selected technology platform(s) was demonstrated at the hot cell mockup facility at the FIU's Applied Research Center tech demo site in Miami, FL. Page 1 of 2 Oak Ridge National Laboratory Tennessee Florida New York D&D Toolbox Project - Technology Demonstration of Fixatives Applied to Hot Cell Facilities via Remote Sprayer Platforms Challenge Many facilities slated for D&D across the DOE complex pose hazards

  6. National Bioenergy Center, Biochemical Platform Integration Project: Quarterly Update, Winter 2011-2012 (Newsletter)

    SciTech Connect (OSTI)

    Not Available

    2012-04-01

    Winter 2011-2012 issue of the National Bioenergy Center Biochemical Platform Integration Project quarterly update. Issue topics: 34th Symposium on Biotechnology for Fuels and Chemicals; feasibility of NIR spectroscopy-based rapid feedstock reactive screening; demonstrating integrated pilot-scale biomass conversion. The Biochemical Process Integration Task focuses on integrating the processing steps in enzyme-based lignocellulose conversion technology. This project supports the U.S. Department of Energy's efforts to foster development, demonstration, and deployment of 'biochemical platform' biorefineries that economically produce ethanol or other fuels, as well as commodity sugars and a variety of other chemical products, from renewable lignocellulosic biomass.

  7. Assessment of an ORION-based experimental platform for measuring the

    Office of Scientific and Technical Information (OSTI)

    opacity of high-temperature and high-density plasma (Technical Report) | SciTech Connect Assessment of an ORION-based experimental platform for measuring the opacity of high-temperature and high-density plasma Citation Details In-Document Search Title: Assessment of an ORION-based experimental platform for measuring the opacity of high-temperature and high-density plasma Authors: Beiersdorfer, P Publication Date: 2012-09-06 OSTI Identifier: 1053680 Report Number(s): LLNL-TR-579939 DOE

  8. APBF-DEC Heavy Duty NOx Adsorber/DPF Project: Heavy Duty Linehaul Platform

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Project Update | Department of Energy Heavy Duty NOx Adsorber/DPF Project: Heavy Duty Linehaul Platform Project Update APBF-DEC Heavy Duty NOx Adsorber/DPF Project: Heavy Duty Linehaul Platform Project Update 2003 DEER Conference Presentation: Ricardo Inc., Chicago Technical Center PDF icon deer_2003_may.pdf More Documents & Publications Status of APBF-DEC NOx Adsorber/DPF Projects APBF- DEC Heavy-Duty NOx Adsorber/DPF Project: Catalyst Aging Study APBF-DEC Light-duty NOx Adsorber/DPF

  9. APBF-DEC NOx Adsorber/DPF Project: SUV/Pick-Up Platform | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy NOx Adsorber/DPF Project: SUV/Pick-Up Platform APBF-DEC NOx Adsorber/DPF Project: SUV/Pick-Up Platform 2003 DEER Conference Presentation: Southwest Research Institute PDF icon 2003_deer_webb.pdf More Documents & Publications Status of APBF-DEC NOx Adsorber/DPF Projects Full Useful Life (120,000 miles) Exhaust Emission Performance of a NOx Adsorber and Diesel Particle Filter Equipped Passenger Car and Medium-Duty Engine in Conjunction with Ultralow-Sulfur Fuel APBF-DEC Light-duty

  10. Ultra Fast X-ray Streak Camera for TIM Based Platforms (Conference) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Ultra Fast X-ray Streak Camera for TIM Based Platforms Citation Details In-Document Search Title: Ultra Fast X-ray Streak Camera for TIM Based Platforms Ultra fast x-ray streak cameras are a staple for time resolved x-ray measurements. There is a need for a ten inch manipulator (TIM) based streak camera that can be fielded in a newer large scale laser facility. The LLNL ultra fast streak camera's drive electronics have been upgraded and redesigned to fit inside a TIM tube.

  11. Innovative Deepwater Platform Aims to Harness Offshore Wind and Wave Power

    Energy Savers [EERE]

    | Department of Energy Deepwater Platform Aims to Harness Offshore Wind and Wave Power Innovative Deepwater Platform Aims to Harness Offshore Wind and Wave Power March 28, 2011 - 5:55pm Addthis An employee installs a smart meter as part of a smart grid initiative by EPB. The project is supporting 390 jobs in the Chattanooga area. | Photo courtesy of EPB An employee installs a smart meter as part of a smart grid initiative by EPB. The project is supporting 390 jobs in the Chattanooga area. |

  12. DOE-Funded Project Develops Safer Access to Offshore Wind Turbine Platforms

    Office of Environmental Management (EM)

    | Department of Energy Funded Project Develops Safer Access to Offshore Wind Turbine Platforms DOE-Funded Project Develops Safer Access to Offshore Wind Turbine Platforms September 10, 2015 - 6:21pm Addthis More than 4,000 gigawatts of estimated gross offshore wind potential lies off the U.S. coastline-that's more than four times the current generation capacity of the United States. With the coastal and Great Lakes states consuming nearly 80% of our nation's electricity, offshore wind can

  13. EM Launches Revamped Website: New cutting-edge platform with sleek

    Office of Environmental Management (EM)

    appearance focuses on ease-of-use | Department of Energy Revamped Website: New cutting-edge platform with sleek appearance focuses on ease-of-use EM Launches Revamped Website: New cutting-edge platform with sleek appearance focuses on ease-of-use January 7, 2013 - 12:00pm Addthis A screenshot of the newly revamped EM website. A screenshot of the newly revamped EM website. EM's previous website EM's previous website A screenshot of the newly revamped EM website. EM's previous website

  14. Global Green Growth Institute | Open Energy Information

    Open Energy Info (EERE)

    Growth Institute Redirect page Jump to: navigation, search REDIRECT Green Growth Strategy Support Retrieved from "http:en.openei.orgwindex.php?titleGlobalGreenGrowthIn...

  15. Exploration Best Practices and the OpenEI Knowledge Exchange...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Exploration Best Practices and the OpenEI Knowledge Exchange Webinar Exploration Best Practices and the OpenEI Knowledge Exchange Webinar Exploration Best Practices and the OpenEI...

  16. New America Foundation: Eric Isaacs - Can our knowledge enterprise...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New America Foundation: Eric Isaacs - Can our knowledge enterprise seed the industries of tomorrow? Share Topic Operations Technology transfer...

  17. The Bioenergy Knowledge Discovery Framework (KDF) | Department of Energy

    Energy Savers [EERE]

    The Bioenergy Knowledge Discovery Framework (KDF) The Bioenergy Knowledge Discovery Framework (KDF) The Bioenergy Knowledge Discovery Framework (KDF) is an online collaboration and geospatial analysis tool that allows researchers, policymakers, and investors to explore and engage the latest bioenergy research. The KDF harnesses Web 2.0 and social networking technologies to build a collective knowledge system that facilitates collaborative production, integration, and analysis of

  18. Biomass Program 2007 Program Peer Review - Biochemical and Products Platform Summary

    SciTech Connect (OSTI)

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Biochemical and Products Platform Review held on August 7-9, 2007 in Denver, Colorado.

  19. National Bioenergy Center - Biochemical Platform Integration Project: Quarterly Update, Winter 2010

    SciTech Connect (OSTI)

    Schell, D.

    2011-02-01

    Winter 2011 edition of the National Bioenergy Center's Biochemical Platform Integration Project quarterly newsletter. Issue topics: 33rd Symposium on Biotechnology for Fuels and Chemicals program topic areas; results from reactive membrane extraction of inhibitors from dilute-acid pretreated corn stover; list of 2010 task publications.

  20. National Bioenergy Center Biochemical Platform Integration Project: Quarterly Update #27, April - June 2010

    SciTech Connect (OSTI)

    Schell, D.

    2010-07-01

    April-June, 2010 edition of the National Bioenergy Center's Biochemical Platform Integration Project quarterly newsletter. Issue topics: understanding performance of alternative process configurations for producing ethanol from biomass; investigating Karl Fischer Titration for measuring water content of pretreated biomass slurries.

  1. Estimating payload internal temperatures and radiator size for multimegawatt space platforms

    SciTech Connect (OSTI)

    Dobranich, D.

    1987-08-01

    A conceptual space platform consists of a payload, a power conditioning unit (PCU), and two radiators: the main radiator and a secondary radiator. A computer program was written to determine the required size of the two radiators and the temperatures of the PCU and payload for a given platform power level. An iterative approach is necessary because the required size of the main radiator depends on the size of the secondary radiator and vice versa. Also, the temperatures of the payload and PCU depend on the size of the radiators. The program user can subdivide the two radiators into any number of nodes to increase the accuracy of the radiant heat transfer solution. The use of more nodes also allows better prediction of the nonlinear temperature drop that occurs across the radiators as the working fluid deposits the platform's waste heat in the radiator. View factor expressions are automatically calculated for different choices of the number of nodes. The user can also select different separation distances between the various platform structures. A model is included to couple the radiant and conduction heat transfer that occurs between the payload and its meteoroid shell and between the PCU and its shell. Also, the program allows the use of a refrigerator to cool the payload. If a refrigerator is used, the program determines the amount of additional thermal power needed to run the refrigerator. The results of parametric calculations are included to demonstrate the use of the program.

  2. Guided evolution of bulk metallic glass nanostructures: A platform for designing three-dimensional electrocatalytic surfaces

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Doubek, Gustavo; Sekol, Ryan C.; Li, Jinyang; Ryu, Won -Hee; Gittleson, Forrest S.; Nejati, Siamak; Moy, Eric; Reid, Candy; Carmo, Marcelo; Linardi, Marcelo; et al

    2015-12-22

    Precise control over catalyst surface composition and structure is necessary to improve the function of electrochemical systems. To that end, bulk metallic glass (BMG) alloys with atomically dispersed elements provide a highly processable, nanoscale platform for electrocatalysis and surface modification. Here we report on nanostructures of Pt-based BMGs that are modified with various subtractive and additive processes to improve their electrochemical performance.

  3. System for beaming power from earth to a high altitude platform

    DOE Patents [OSTI]

    Friedman, Herbert W. (Oakland, CA); Porter, Terry J. (Ridgecrest, CA)

    2002-01-01

    Power is transmitted to a high altitude platform by an array of diode pumped solid state lasers each operated at a single range of laser wavelengths outside of infrared and without using adaptive optics. Each laser produces a beam with a desired arrival spot size. An aircraft avoidance system uses a radar system for automatic control of the shutters of the lasers.

  4. Investigating methods of supporting dynamically linked executables on high performance computing platforms.

    SciTech Connect (OSTI)

    Kelly, Suzanne Marie; Laros, James H., III; Pedretti, Kevin Thomas Tauke; Levenhagen, Michael J.

    2009-09-01

    Shared libraries have become ubiquitous and are used to achieve great resource efficiencies on many platforms. The same properties that enable efficiencies on time-shared computers and convenience on small clusters prove to be great obstacles to scalability on large clusters and High Performance Computing platforms. In addition, Light Weight operating systems such as Catamount have historically not supported the use of shared libraries specifically because they hinder scalability. In this report we will outline the methods of supporting shared libraries on High Performance Computing platforms using Light Weight kernels that we investigated. The considerations necessary to evaluate utility in this area are many and sometimes conflicting. While our initial path forward has been determined based on this evaluation we consider this effort ongoing and remain prepared to re-evaluate any technology that might provide a scalable solution. This report is an evaluation of a range of possible methods of supporting dynamically linked executables on capability class1 High Performance Computing platforms. Efforts are ongoing and extensive testing at scale is necessary to evaluate performance. While performance is a critical driving factor, supporting whatever method is used in a production environment is an equally important and challenging task.

  5. National Bioenergy Center Biochemical Platform Integration Project: Quarterly Update #28, Spring 2011

    SciTech Connect (OSTI)

    Schell, D. J.

    2011-04-01

    Spring 2011 edition of the National Bioenergy Center's Biochemical Platform Integration Project quarterly newsletter. Issue topics: 33rd Symposium on Biotechnology for Fuels and Chemicals program sessions and special topic sessions; assessment of waste water treatment needs; and an update on new arabinose-to-ethanol fermenting Zymomonas mobilis strains.

  6. Essential Body of Knowledge (EBK) | Department of Energy

    Office of Environmental Management (EM)

    Essential Body of Knowledge (EBK) Essential Body of Knowledge (EBK) A Competency and Functional Framework For Cyber Security Workforce Development Documents Available for Download More Documents & Publications Essential Body of Knowledge (EBK) DOE CYBER SECURITY EBK: CORE COMPETENCY TRAINING REQUIREMENTS: CA DOE CYBER SECURITY EBK: MINIMUM CORE COMPETENCY TRAINING REQUIREMENTS

  7. Measuring and tuning energy efficiency on large scale high performance computing platforms.

    SciTech Connect (OSTI)

    Laros, James H., III

    2011-08-01

    Recognition of the importance of power in the field of High Performance Computing, whether it be as an obstacle, expense or design consideration, has never been greater and more pervasive. While research has been conducted on many related aspects, there is a stark absence of work focused on large scale High Performance Computing. Part of the reason is the lack of measurement capability currently available on small or large platforms. Typically, research is conducted using coarse methods of measurement such as inserting a power meter between the power source and the platform, or fine grained measurements using custom instrumented boards (with obvious limitations in scale). To collect the measurements necessary to analyze real scientific computing applications at large scale, an in-situ measurement capability must exist on a large scale capability class platform. In response to this challenge, we exploit the unique power measurement capabilities of the Cray XT architecture to gain an understanding of power use and the effects of tuning. We apply these capabilities at the operating system level by deterministically halting cores when idle. At the application level, we gain an understanding of the power requirements of a range of important DOE/NNSA production scientific computing applications running at large scale (thousands of nodes), while simultaneously collecting current and voltage measurements on the hosting nodes. We examine the effects of both CPU and network bandwidth tuning and demonstrate energy savings opportunities of up to 39% with little or no impact on run-time performance. Capturing scale effects in our experimental results was key. Our results provide strong evidence that next generation large-scale platforms should not only approach CPU frequency scaling differently, but could also benefit from the capability to tune other platform components, such as the network, to achieve energy efficient performance.

  8. Facies variation and evolution of a peri-Adriatic carbonate platform in the region of Sorrento, southern Italy

    SciTech Connect (OSTI)

    Robson, J. )

    1988-08-01

    In the region around Sorrento, Cretaceous carbonates attributed to inner platform facies outcrop, and farther south lithologies indicate deposition in a floreslope/basin environment. Sedimentological logging shows significant changes in facies associations from the Aptian to the Cenomanian-Turonian. These changes indicate variation in depositional environment through time with respect to the stability of the western margin of the platform.

  9. A Comparison of Platform Options for Deep-water Floating Offshore Vertical Axis Wind Turbines: An Initial Study.

    SciTech Connect (OSTI)

    Bull, Diana L; Fowler, Matthew; Goupee, Andrew

    2014-08-01

    This analysis utilizes a 5 - MW VAWT topside design envelope created by Sandia National Laborator ies to compare floating platform options fo r each turbine in the design space. The platform designs are based on two existing designs, the OC3 Hywind spar - buoy and Principal Power's WindFloat semi - submersible. These designs are scaled using Froude - scaling relationships to determine an appropriately sized spar - buoy and semi - submersible design for each topside. Both the physical size of the required platform as well as mooring configurations are considered. Results are compared with a comparable 5 - MW HAWT in order to identify potential differences in the platform and mooring sizing between the VAWT and HAWT . The study shows that there is potential for cost savings due to reduced platform size requirements for the VAWT.

  10. ISO 14000 information platform. Quarterly report, January 1--March 31, 1998

    SciTech Connect (OSTI)

    1998-09-01

    GETE, through its ISO 14000 Information Platform, globeNet{trademark} (www.iso14000.net), seeks to provide FETC and the US Department of Energy (DOE) with a timely, accurate, and reliable information resource on the issue of environmental management standards. This resource allows FETC to keep track of the latest developments in the ISO 14000 arena, in DOE as well as throughout the federal complex and industry. Utilizing this information, FETC and DOE can make critical decisions on their own use and implementation of the ISO 14000 standards. The information platform also provides FETC with a forum to present information on its activities, such as the DOE ISO 14000 Pilot Projects, and as an information gathering and dissemination resource for its publications. GETE works with an array of national and international contacts and content sources to gather information and provide daily updates on ISO 14000 and related environmental management issues.

  11. Grid Simulator for Testing a Wind Turbine on Offshore Floating Platform

    SciTech Connect (OSTI)

    Gevorgian, V.

    2012-02-01

    An important aspect of such offshore testing of a wind turbine floating platform is electrical loading of the wind turbine generator. An option of interconnecting the floating wind turbine with the onshore grid via submarine power cable is limited by many factors such as costs and associated environmental aspects (i.e., an expensive and lengthy sea floor study is needed for cable routing, burial, etc). It appears to be a more cost effective solution to implement a standalone grid simulator on a floating platform itself for electrical loading of the test wind turbine. Such a grid simulator must create a stable fault-resilient voltage and frequency bus (a micro grid) for continuous operation of the test wind turbine. In this report, several electrical topologies for an offshore grid simulator were analyzed and modeled.

  12. Towards Composing Data Aware Systems Biology Workflows on Cloud Platforms: A MeDICi-based Approach

    SciTech Connect (OSTI)

    Gorton, Ian; Liu, Yan; Yin, Jian; Kulkarni, Anand V.; Wynne, Adam S.

    2011-09-08

    Cloud computing is being increasingly adopted for deploying systems biology scientific workflows. Scientists developing these workflows use a wide variety of fragmented and competing data sets and computational tools of all scales to support their research. To this end, the synergy of client side workflow tools with cloud platforms is a promising approach to share and reuse data and workflows. In such systems, the location of data and computation is essential consideration in terms of quality of service for composing a scientific workflow across remote cloud platforms. In this paper, we describe a cloud-based workflow for genome annotation processing that is underpinned by MeDICi - a middleware designed for data intensive scientific applications. The workflow implementation incorporates an execution layer for exploiting data locality that routes the workflow requests to the processing steps that are colocated with the data. We demonstrate our approach by composing two workflowswith the MeDICi pipelines.

  13. Development of a propulsion system and component test facility for advanced radioisotope powered Mars Hopper platforms

    SciTech Connect (OSTI)

    Robert C. O'Brien; Nathan D. Jerred; Steven D. Howe

    2011-02-01

    Verification and validation of design and modeling activities for radioisotope powered Mars Hopper platforms undertaken at the Center for Space Nuclear Research is essential for proof of concept. Previous research at the center has driven the selection of advanced material combinations; some of which require specialized handling capabilities. The development of a closed and contained test facility to forward this research is discussed within this paper.

  14. NREL Thermochemical Platform Analysis Presentation for BETO 2015 Project Peer Review

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (BETO) 2015 Project Peer Review: NREL Thermochemical Platform Analysis Presenter: Abhijit Dutta on behalf of Mary Biddy, Jack Ferrell and Michael Talmadge (PI) BETO 2015 Project Peer Review Hilton Mark Center, Alexandria, VA March 26, 2015 2 1. Goal and Supporting Objectives Goal Statement: Develop process and techno-economic models for biomass-to-fuels research. * Develop design cases / reports to identify barriers and set technical and cost targets for cost competitiveness by 2022 * Use

  15. EM Quality Assurance Centralized Training Platform Project Plan for 2009-2010

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    OFFICE OF ENVIRONMENTAL MANAGEMENT QUALITY ASSURANCE IMPROVEMENT INITIATIVE EM CENTRALIZED TRAINING PLATFORM PROJECT PLAN Prepared by: Date: Approved by: Date: Revision 0 Page 3 of 30 05/11/09 1.0 INTRODUCTION The Department of Energy (DOE) expertise in quality assurance (QA) has degraded significantly over the last 10 years due to workforce attrition and the lack of emphasis on QA principles. Since the 2007 establishment and subsequent implementation of the Office of Environmental Management

  16. NREL Computer Models Integrate Wind Turbines with Floating Platforms (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-07-01

    Far off the shores of energy-hungry coastal cities, powerful winds blow over the open ocean, where the water is too deep for today's seabed-mounted offshore wind turbines. For the United States to tap into these vast offshore wind energy resources, wind turbines must be mounted on floating platforms to be cost effective. Researchers at the National Renewable Energy Laboratory (NREL) are supporting that development with computer models that allow detailed analyses of such floating wind turbines.

  17. Leak Detection/Fugitive Emissions Monitoring and Advanced Sensors, Controls, Models and Platforms Panel

    Office of Environmental Management (EM)

    and Methane Emissions Mitigation Workshop Leak Detection/Fugitive Emissions Monitoring and Advanced Sensors, Controls, Models and Platforms Panel November 12, 2014 POUND FOR POUND METHANE TRAPS 84X MORE HEAT OVER 20 YEARS CO2 CH4 Methane is Money $1,800,000,000 Current technologies - economic and effective * Economic cost benefit analysis * Industry input included * Main finding: Cut emissions 40% at $0.01/McF reduced * OGI provides reliable and proven means of detecting leaks * EPA White Paper

  18. Processes, data structures, and apparatuses for representing knowledge

    DOE Patents [OSTI]

    Hohimer, Ryan E. (West Richland, WA); Thomson, Judi R. (Guelph, CA); Harvey, William J. (Richland, WA); Paulson, Patrick R. (Pasco, WA); Whiting, Mark A. (Richland, WA); Tratz, Stephen C. (Richland, WA); Chappell, Alan R. (Seattle, WA); Butner, R. Scott (Richland, WA)

    2011-09-20

    Processes, data structures, and apparatuses to represent knowledge are disclosed. The processes can comprise labeling elements in a knowledge signature according to concepts in an ontology and populating the elements with confidence values. The data structures can comprise knowledge signatures stored on computer-readable media. The knowledge signatures comprise a matrix structure having elements labeled according to concepts in an ontology, wherein the value of the element represents a confidence that the concept is present in an information space. The apparatus can comprise a knowledge representation unit having at least one ontology stored on a computer-readable medium, at least one data-receiving device, and a processor configured to generate knowledge signatures by comparing datasets obtained by the data-receiving devices to the ontologies.

  19. Capturing Process Knowledge for Facility Deactivation and Decommissioning

    Office of Environmental Management (EM)

    Tech Assistance Savannah River National Laboratory- Assess Adequacy of Process Knowledge for D&D Guidance for Determining Adequacy of Process Knowledge Page 1 of 2 Savannah River National Laboratory South Carolina Capturing Process Knowledge for Facility Deactivation and Decommissioning Challenge The Office of Environmental Management (EM) is responsible for the disposition of a vast number of facilities at numerous sites around the country which have been declared excess to current mission

  20. Prior-knowledge-based spectral mixture analysis for impervious surface

    Office of Scientific and Technical Information (OSTI)

    mapping (Journal Article) | SciTech Connect SciTech Connect Search Results Journal Article: Prior-knowledge-based spectral mixture analysis for impervious surface mapping Citation Details In-Document Search Title: Prior-knowledge-based spectral mixture analysis for impervious surface mapping In this study, we developed a prior-knowledge-based spectral mixture analysis (PKSMA) to map impervious surfaces by using endmembers derived separately for high- and low-density urban regions. First, an

  1. Isotropic Monte Carlo Grain Growth

    Energy Science and Technology Software Center (OSTI)

    2013-04-25

    IMCGG performs Monte Carlo simulations of normal grain growth in metals on a hexagonal grid in two dimensions with periodic boundary conditions. This may be performed with either an isotropic or a misorientation - and incliantion-dependent grain boundary energy.

  2. MOWII Webinar: The ECO TLP, an Economical and Ecologically Sound Tension Leg Platform for Deep Water Wind Farms

    Broader source: Energy.gov [DOE]

    Join the Maine Ocean and Wind industry Initiative (MOWII) for a free webinar that describes the components and installation process of economical and ecologically sound tension leg platforms for...

  3. NUCLEAR INCIDENT CAPABILITIES, KNOWLEDGE & ENABLER LEVERAGING

    SciTech Connect (OSTI)

    Kinney, J.; Newman, J.; Goodwyn, A.; Dewes, J.

    2011-04-18

    The detonation of a 10 Kiloton Improvised Nuclear Device (IND) is a serious scenario that the United States must be prepared to address. The likelihood of a single nuclear bomb exploding in a single city is greater today than at the height of the Cold War. Layered defenses against domestic nuclear terrorism indicate that our government continues to view the threat as credible. The risk of such an event is further evidenced by terrorists desire to acquire nuclear weapons. The act of nuclear terrorism, particularly an act directed against a large population center in the United States, will overwhelm the capabilities of many local and state governments to respond, and will seriously challenge existing federal response capabilities. A 10 Kiloton IND detonation would cause total infrastructure damage in a 3-mile radius and levels of radiation spanning out 3,000 square miles. In a densely populated urban area, the anticipated casualties would be in excess of several hundred thousand. Although there would be enormous loss of life, housing and infrastructure, an IND detonation is a recoverable event. We can reduce the risk of these high-consequence, nontraditional threats by enhancing our nuclear detection architecture and establishing well planned and rehearsed plans for coordinated response. It is also important for us to identify new and improved ways to foster collaboration regarding the response to the IND threat to ensure the demand and density of expertise required for such an event is postured and prepared to mobilize, integrate, and support a myriad of anticipated challenges. We must be prepared to manage the consequences of such an event in a deliberate manner and get beyond notions of total devastation by adopting planning assumptions around survivability and resiliency. Planning for such a scenario needs to be decisive in determining a response based on competencies and desired outcomes. It is time to synthesize known threats and plausible consequences into action. Much work needs to be accomplished to enhance nuclear preparedness and to substantially bolster and clarify the capacity to deploy competent resources. Until detailed plans are scripted, and personnel and other resources are postured, and exercised, IND specific planning remains an urgent need requiring attention and action. Although strategic guidance, policies, concepts of operations, roles, responsibilities, and plans governing the response and consequence management for the IND scenario exist, an ongoing integration challenge prevails regarding how best to get capable and competent surge capacity personnel (disaster reservists) and other resources engaged and readied in an up-front manner with pre-scripted assignments to augment the magnitude of anticipated demands of expertise. With the above in mind, Savannah River National Laboratory (SRNL) puts science to work to create and deploy practical, high-value, cost-effective nuclear solutions. As the Department of Energy's (DOE) applied research and development laboratory, SRNL supports Savannah River Site (SRS) operations, DOE, national initiatives, and other federal agencies, across the country and around the world. SRNL's parent at SRS also employs more than 8,000 personnel. The team is a great asset that seeks to continue their service in the interest of national security and stands ready to accomplish new missions. Overall, an integral part of the vision for SRNL's National and Homeland Security Directorate is the establishment of a National Security Center at SRNL, and development of state of the science capabilities (technologies and trained technical personnel) for responding to emergency events on local, regional, or national scales. This entails leveraging and posturing the skills, knowledge and experience base of SRS personnel to deliver an integrated capability to support local, state, and federal authorities through the development of pre-scripted requests for assistance, agreements, and plans. It also includes developing plans, training, exercises, recruitment strategies, and processes to e

  4. Chapter 6: Innovating Clean Energy Technologies in Advanced Manufacturing | Advanced Sensors, Controls, Platforms and Modeling for Manufacturing Technology Assessment

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Sensors, Controls, Platforms and Modeling for Manufacturing Chapter 6: Technology Assessments NOTE: This technology assessment is available as an appendix to the 2015 Quadrennial Technology Review (QTR). Advanced Sensors, Controls, Platforms and Modeling for Manufacturing is one of fourteen manufacturing-focused technology assessments prepared in support of Chapter 6: Innovating Clean Energy Technologies in Advanced Manufacturing. For context within the 2015 QTR, key connections between

  5. NREL Establishes a 1.5-MW Wind Turbine Test Platform for Research Partnerships (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2012-03-01

    Research turbine supports sustained technology development. For more than three decades, engineers at the National Renewable Energy Laboratory's (NREL) National Wind Technology Center (NWTC) have worked with the U.S. Department of Energy (DOE) Wind Program and industry partners to advance wind energy technology, improve wind turbine performance, and reduce the cost of energy. Although there have been dramatic increases in performance and drops in the cost of wind energy-from $0.80 per kilowatt-hour to between $0.06 and $0.08 per kilowatt-hour-the goal of the DOE Wind Program is to further increase performance and reduce the cost of energy for land-based systems so that wind energy can compete with natural gas by 2020. In support of the program's research and development (R and D) efforts, NREL has constructed state-of-the-art facilities at the NWTC where industry partners, universities, and other DOE laboratories can conduct tests and experiments to further advance wind technology. The latest facility to come online is the DOE-GE 1.5-MW wind turbine test platform. Working with DOE, NREL purchased and installed a GE 1.5-MW wind turbine at the NWTC in 2009. Since then, NREL engineers have extensively instrumented the machine, conducted power performance and full-system modal tests, and collected structural loads measurements to obtain baseline characterization of the turbine's power curve, vibration characteristics, and fatigue loads in the uniquely challenging NWTC inflow environment. By successfully completing a baseline for the turbine's performance and structural response, NREL engineers have established a test platform that can be used by industry, university, and DOE laboratory researchers to test wind turbine control systems and components. The new test platform will also enable researchers to acquire the measurements needed to develop and validate wind turbine models and improve design codes.

  6. A new vehicle data bus architecture and IVIS evaluation platform for ITS modulus

    SciTech Connect (OSTI)

    Spelt, P.F.; Kirson, A.M.; Scott, S.

    1998-12-31

    An increasing number of ITS-related after-market systems present a set of in-vehicle installation and use problems relatively unique in the history of automobile use. Many automobile manufacturers would like to offer these new state of the art devices to customers, but are hampered by the current design cycle of new cars. While auto manufacturers are indeed using multiplex buses (the automotive equivalent of a computer local area network), problems remain because manufacturers are not converging on a single bus standard. This paper presents a new dual-bus architecture to address these problems, with an In-Vehicle Information System (IVIS) research platform on which the principles embodied in the ITS Data Bus architecture can be evaluated. The dual-bus architecture has been embodied in a proposed SAE standard, with a ratification vote in December, 1996. The architecture and a reference model for the interfaces and protocols of the new bus are presented and described. The goals of the ITS Data Bus are to be inexpensive and easy to install, and to provide for safe and secure functioning. These high-level goals are embodied in the proposed standard. The IVIS Development Platform comprises a number of personal computers linked via ethernet LAN, with a high-end PC serving as the IVIS computer. In this LAN, actual devices can be inserted in place of the original PC which emulated them. This platform will serve as the development and test bed for an ITS Data Bus Conformity Test, the SAE standard for which has also been developed.

  7. Microfluidic Development Platform for Nanowire-based BioSensor Applications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Microfluidic Development Platform for Nanowire-based BioSensor Applications Jost Goettert 1 , Yoonyoung Jin 1, 2 (part time), Kyung-Nan Kang 1 , Jeonghwan Kim 1 , Hui Ma 3 , Seth Pincus 4 , Sital Tiwari 1 (part time), Kun Yao, Dawit Yemane 1 , Weilie Zhou 3 1 LSU Center for Advanced Microstructures and Devices (CAMD), Baton Rouge, LA 2 NextGenC3 Composites CREST Center, Southern University and A&M College, USA 3 Advanced Materials Research Institute (AMRI), University of New Orleans 4 LSU

  8. Design and Optimization of a Biochemical Production Platform with Biosensor-Guided Synthetic Evolution

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    3, 2015 DOE BETO Conversion Review Eric J. Steen, Ph.D. Lygos, Inc. DESIGN & OPTIMIZATION OF A BIOCHEMICAL PRODUCTION PLATFORM WITH BIOSENSOR-GUIDED SYNTHETIC EVOLUTION 2 CELLULOSIC SUGARS MALONYL-COA FATTY ACIDS MALONIC ACID § Malonyl-CoA lies on the carbon superhighway in biology § Pathway is compatible with all available, low-cost feedstocks § Malonyl-CoA is basis of fatty acid production (90%+ yields reported) § Malonic acid is an ideal molecule to produce biologically

  9. New Modeling Tool Analyzes Floating Platform Concepts for Offshore Wind Turbines (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-02-01

    Researchers at the National Renewable Energy Laboratory (NREL) developed a new complex modeling and analysis tool capable of analyzing floating platform concepts for offshore wind turbines. The new modeling tool combines the computational methodologies used to analyze land-based wind turbines with the comprehensive hydrodynamic computer programs developed for offshore oil and gas industries. This new coupled dynamic simulation tool will enable the development of cost-effective offshore technologies capable of harvesting the rich offshore wind resources at water depths that cannot be reached using the current technology.

  10. Office of Nuclear Energy Knowledge Management Program Situational Analysis Report

    SciTech Connect (OSTI)

    Kimberlyn C. Mousseau

    2011-12-01

    Knowledge management (KM) has been a high priority for the Department of Energy (DOE) Office of Nuclear Energy (NE) for the past several years. NE Programs are moving toward well-established knowledge management practices and a formal knowledge management program has been established. Knowledge management is being practiced to some level within each of the NE programs. Although it continues to evolve as NE programs evolve, a formal strategic plan that guides the implementation of KM has been developed. Despite the acceptance of KM within DOE NE, more work is necessary before the NE KM program can be considered fully successful. Per Dr. David J. Skyrme[1], an organization typically moves through the following evolutionary phases: (1) Ad-hoc - KM is being practiced to some level in some parts of the organization; (2) Formal - KM is established as a formal project or program; (3) Expanding - the use of KM as a discipline grows in practice across different parts of the organization; (4) Cohesive - there is a degree of coordination of KM; (5) Integrated - there are formal standards and approaches that give every individual access to most organizational knowledge through common interfaces; and (6) Embedded - KM is part-and-parcel of everyday tasks; it blends seamlessly into the background. According to the evolutionary phases, the NE KM program is operating at the two lower levels, Ad-hoc and Formal. Although KM is being practiced to some level, it is not being practiced in a consistent manner across the NE programs. To be fully successful, more emphasis must be placed on establishing KM standards and processes for collecting, organizing, sharing and accessing NE knowledge. Existing knowledge needs to be prioritized and gathered on a routine basis, its existence formally recorded in a knowledge inventory. Governance to ensure the quality of the knowledge being used must also be considered. For easy retrieval, knowledge must be organized according to a taxonomy that mimics nuclear energy programs. Technologies need to be established to make accessing the knowledge easier for the user. Finally, knowledge needs to be used as part of a well defined work process.

  11. Sustaining knowledge in the neutron generator community and benchmarking study.

    SciTech Connect (OSTI)

    Barrentine, Tameka C.; Kennedy, Bryan C.; Saba, Anthony W.; Turgeon, Jennifer L.; Schneider, Julia Teresa; Stubblefield, William Anthony; Baldonado, Esther

    2008-03-01

    In 2004, the Responsive Neutron Generator Product Deployment department embarked upon a partnership with the Systems Engineering and Analysis knowledge management (KM) team to develop knowledge management systems for the neutron generator (NG) community. This partnership continues today. The most recent challenge was to improve the current KM system (KMS) development approach by identifying a process that will allow staff members to capture knowledge as they learn it. This 'as-you-go' approach will lead to a sustainable KM process for the NG community. This paper presents a historical overview of NG KMSs, as well as research conducted to move toward sustainable KM.

  12. Digital electronic bone growth stimulator

    DOE Patents [OSTI]

    Kronberg, J.W.

    1995-05-09

    A device is described for stimulating bone tissue by applying a low level alternating current signal directly to the patient`s skin. A crystal oscillator, a binary divider chain and digital logic gates are used to generate the desired waveforms that reproduce the natural electrical characteristics found in bone tissue needed for stimulating bone growth and treating osteoporosis. The device, powered by a battery, contains a switch allowing selection of the correct waveform for bone growth stimulation or osteoporosis treatment so that, when attached to the skin of the patient using standard skin contact electrodes, the correct signal is communicated to the underlying bone structures. 5 figs.

  13. Digital electronic bone growth stimulator

    DOE Patents [OSTI]

    Kronberg, James W.

    1995-01-01

    A device for stimulating bone tissue by applying a low level alternating current signal directly to the patient's skin. A crystal oscillator, a binary divider chain and digital logic gates are used to generate the desired waveforms that reproduce the natural electrical characteristics found in bone tissue needed for stimulating bone growth and treating osteoporosis. The device, powered by a battery, contains a switch allowing selection of the correct waveform for bone growth stimulation or osteoporosis treatment so that, when attached to the skin of the patient using standard skin contact electrodes, the correct signal is communicated to the underlying bone structures.

  14. Nonlinear structural crack growth monitoring

    DOE Patents [OSTI]

    Welch, Donald E. (Oak Ridge, TN); Hively, Lee M. (Philadelphia, TN); Holdaway, Ray F. (Clinton, TN)

    2002-01-01

    A method and apparatus are provided for the detection, through nonlinear manipulation of data, of an indicator of imminent failure due to crack growth in structural elements. The method is a process of determining energy consumption due to crack growth and correlating the energy consumption with physical phenomena indicative of a failure event. The apparatus includes sensors for sensing physical data factors, processors or the like for computing a relationship between the physical data factors and phenomena indicative of the failure event, and apparatus for providing notification of the characteristics and extent of such phenomena.

  15. Fostering Growth | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Soft Costs » Fostering Growth Fostering Growth The solar energy industry in the United States is growing rapidly as the price of solar panels has decreased over the past decade. U.S. solar installations doubled from 2009 to 2010, and the domestic market was worth $6 billion in 2010. Despite this upward trend, solar energy is only 1% of the current U.S. electricity supply. The SunShot Vision Study says that cost-competitive solar has an estimated potential to supply roughly 14% of domestic

  16. Changes in the peripheral blood transcriptome associated with occupational benzene exposure identified by cross-comparison on two microarray platforms

    SciTech Connect (OSTI)

    McHale, Cliona M.; Zhang, Luoping; Lan, Qing; Li, Guilan; Hubbard, Alan E.; Forrest, Matthew S.; Vermeulen, Roel; Chen, Jinsong; Shen, Min; Rappaport, Stephen M.; Yin, Songnian; Smith, Martyn T.; Rothman, Nathaniel

    2009-03-01

    Benzene is an established cause of leukemia and a possible cause of lymphoma in humans but the molecular pathways underlying this remain largely undetermined. This study sought to determine if the use of two different microarray platforms could identify robust global gene expression and pathway changes associated with occupational benzene exposure in the peripheral blood mononuclear cell (PBMC) gene expression of a population of shoe-factory workers with well-characterized occupational exposures to benzene. Microarray data was analyzed by a robust t-test using a Quantile Transformation (QT) approach. Differential expression of 2692 genes using the Affymetrix platform and 1828 genes using the Illumina platform was found. While the overall concordance in genes identified as significantly associated with benzene exposure between the two platforms was 26% (475 genes), the most significant genes identified by either array were more likely to be ranked as significant by the other platform (Illumina = 64%, Affymetrix = 58%). Expression ratios were similar among the concordant genes (mean difference in expression ratio = 0.04, standard deviation = 0.17). Four genes (CXCL16, ZNF331, JUN and PF4), which we previously identified by microarray and confirmed by real-time PCR, were identified by both platforms in the current study and were among the top 100 genes. Gene Ontology analysis showed over representation of genes involved in apoptosis among the concordant genes while Ingenuity{reg_sign} Pathway Analysis (IPA) identified pathways related to lipid metabolism. Using a two-platform approach allows for robust changes in the PBMC transcriptome of benzene-exposed individuals to be identified.

  17. Seismic model of a progradational carbonate platform, Picco di Vallandro, the Dolomites, northern Italy

    SciTech Connect (OSTI)

    Biddle, K.T.; Bush, T.L. ); Schlager, W. ); Rudolph, K.W. )

    1992-01-01

    The authors present a seismic model of a well-exposed carbonate platform-to-basin transition from the Triassic succession at Picco di Vallandro, the Dolomites, northern Italy. The core of this model is a detailed lithologic cross section that represents 1,500 m of stratigraphic section over a distance of 3.5 km. The cross section is based on detailed measured sections, photo interpretation, and careful projection of surface mapping into the plane of section. Samples from the measured sections provide control on velocity and density distribution, and these data were used to generate an impedance model from the cross section. The impedance model was convolved with a zero-phase, 25-Hz peak-frequency wavelet to produce the seismic model. The results illustrate how the platform-to-basin transition might be imaged by conventional seismic reflection data, how the reflections relate to the distribution of lithology and through-going geological surfaces, and how constructive and destructive interference and seismic resolution combine to produce individual reflections.

  18. The Olympics of science knowledge at DOE's New Jersey Regional...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Olympics of science knowledge at DOE's New Jersey Regional Science Bowl at PPPL By Jeanne Jackson DeVoe March 3, 2014 Tweet Widget Google Plus One Share on Facebook The J...

  19. Energy Efficiency Exchange 2015: Federal Training and Knowledge

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Efficiency Exchange 2015: Federal Training and Knowledge Overview Webinars: March 25 & April 8, 2015 Timothy D. Unruh PhD, PE, CEM Program Director DOE FEMP 2 Energy...

  20. The Importance of Traditional Ecological Knowledge in Adaptation Planning

    Broader source: Energy.gov [DOE]

    The National Adaptation Forum is hosting a webinar to focus on the importance and role of traditional ecological knowledge in adaptation planning at the local, regional, and national level.

  1. Direct flow crystal growth system

    DOE Patents [OSTI]

    Montgomery, Kenneth E. (Tracy, CA); Milanovich, Fred P. (Lafayette, CA)

    1992-01-01

    A crystal is grown in a constantly filtered solution which is flowed directly into the growing face of a crystal. In a continuous flow system, solution at its saturation temperature is removed from a crystal growth tank, heated above its saturation temperature, filtered, cooled back to its saturation temperature, and returned to the tank.

  2. 2015 NREL Industry Growth Forum

    Broader source: Energy.gov [DOE]

    During NREL’s 2015 Industry Growth Forum, 30 competitively selected clean energy startups will pitch their businesses to investors and compete to win the NREL Best Venture Award.  One of the...

  3. SBA Growth Accelerator Fund Competition

    Broader source: Energy.gov [DOE]

    The U.S. Small Business Administration (SBA) is accepting applications for the Growth Accelerator Fund Competition to identify the nation's innovative accelerators and similar organizations and award them cash prizes they may use to fund their operations costs and allow them to bring startup competitions to scale and new ideas to life.

  4. The process for integrating the NNSA knowledge base.

    SciTech Connect (OSTI)

    Wilkening, Lisa K.; Carr, Dorthe Bame; Young, Christopher John; Hampton, Jeff; Martinez, Elaine

    2009-03-01

    From 2002 through 2006, the Ground Based Nuclear Explosion Monitoring Research & Engineering (GNEMRE) program at Sandia National Laboratories defined and modified a process for merging different types of integrated research products (IRPs) from various researchers into a cohesive, well-organized collection know as the NNSA Knowledge Base, to support operational treaty monitoring. This process includes defining the KB structure, systematically and logically aggregating IRPs into a complete set, and verifying and validating that the integrated Knowledge Base works as expected.

  5. Flex Your Electric Vehicle Knowledge Muscle On Jeopardy! Tonight |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Department of Energy Flex Your Electric Vehicle Knowledge Muscle On Jeopardy! Tonight Flex Your Electric Vehicle Knowledge Muscle On Jeopardy! Tonight May 20, 2011 - 9:30am Addthis Ginny Simmons Ginny Simmons Former Managing Editor for Energy.gov, Office of Public Affairs One of the Department of Energy's great prides -- the Argonne National Laboratory -- will be featured in today's episode of Jeopardy! Contestants will answer questions in a "Cars of Today" category, which will

  6. To the Cloud! Apidae Helps Modelers Turn Information into Knowledge |

    Energy Savers [EERE]

    Department of Energy To the Cloud! Apidae Helps Modelers Turn Information into Knowledge To the Cloud! Apidae Helps Modelers Turn Information into Knowledge October 26, 2015 - 2:41pm Addthis Apidae is a collection of cloud-based simulation and data analysis tools that help modelers better understand their models. Image credit: BUILDlab. Apidae is a collection of cloud-based simulation and data analysis tools that help modelers better understand their models. Image credit: BUILDlab. Apidae

  7. Sioux Students Kindle Solar Knowledge | Department of Energy

    Energy Savers [EERE]

    Sioux Students Kindle Solar Knowledge Sioux Students Kindle Solar Knowledge July 24, 2013 - 11:30am Addthis Students and instructors at Oglala Lakota College designed, connected and built a mobile solar energy system over the course of two days. | Photo courtesy of Oglala Lakota College. Students and instructors at Oglala Lakota College designed, connected and built a mobile solar energy system over the course of two days. | Photo courtesy of Oglala Lakota College. Minh Le Minh Le Deputy

  8. 'Big Data' Collaboration: Exploring, Recording and Sharing Enterprise Knowledge

    SciTech Connect (OSTI)

    Sukumar, Sreenivas R; Ferrell, Regina Kay

    2013-01-01

    As data sources and data size proliferate, knowledge discovery from "Big Data" is starting to pose several challenges. In this paper, we address a specific challenge in the practice of enterprise knowledge management while extracting actionable nuggets from diverse data sources of seemingly-related information. In particular, we address the challenge of archiving knowledge gained through collaboration, dissemination and visualization as part of the data analysis, inference and decision-making lifecycle. We motivate the implementation of an enterprise data-discovery and knowledge recorder tool, called SEEKER based on real world case-study. We demonstrate SEEKER capturing schema and data-element relationships, tracking the data elements of value based on the queries and the analytical artifacts that are being created by analysts as they use the data. We show how the tool serves as digital record of institutional domain knowledge and a documentation for the evolution of data elements, queries and schemas over time. As a knowledge management service, a tool like SEEKER saves enterprise resources and time by avoiding analytic silos, expediting the process of multi-source data integration and intelligently documenting discoveries from fellow analysts.

  9. SU-E-J-45: Design and Study of An In-House Respiratory Gating Phantom Platform for Gated Radiotherapy

    SciTech Connect (OSTI)

    Senthilkumar, S

    2014-06-01

    Purpose: The main purpose of this work was to develop an in-house low cost respiratory motion phantom platform for testing the accuracy of the gated radiotherapy system and analyze the dosimetric difference during gated radiotherapy. Methods: An in-house respiratory motion platform(RMP) was designed and constructed for testing the targeting accuracy of respiratory tracking system. The RMP consist of acrylic Chest Wall Platform, 2 DC motors, 4 IR sensors, speed controller circuit, 2 LED and 2 moving rods inside the RMP. The velocity of the movement can be varied from 0 to 30 cycles per minute. The platform mounted to a base using precision linear bearings. The base and platform are made of clear, 15mm thick polycarbonate plastic and the linear ball bearings are oriented to restrict the platform to a movement of approximately 50mm up and down with very little friction. Results: The targeting accuracy of the respiratory tracking system was evaluated using phantom with and without respiratory movement with varied amplitude. We have found the 5% dose difference to the PTV during the movement in comparison with stable PTV. The RMP can perform sinusoidal motion in 1D with fixed peak to peak motion of 5 to 50mm and cycle interval from 2 to 6 seconds. The RMP was designed to be able to simulate the gross anatomical anterior posterior motion attributable to respiration-induced motion of the thoracic region. Conclusion: The unique RMP simulates breathing providing the means to create a comprehensive program for commissioning, training, quality assurance and dose verification of gated radiotherapy treatments. Create the anterior/posterior movement of a target over a 5 to 50 mm distance to replicate tumor movement. The targeting error of the respiratory tracking system is less than 1.0 mm which shows suitable for clinical treatment with highly performance.

  10. The Mars Hopper: a radioisotope powered, impulse driven, long-range, long-lived mobile platform for exploration of Mars

    SciTech Connect (OSTI)

    Steven D. Howe; Robert C. O'Brien; William Taitano; Doug Crawford; Nathan Jerred; Spencer Cooley; John Crapeau; Steve Hansen; Andrew Klein; James Werner

    2011-02-01

    Planetary exploration mission requirements are becoming more demanding. Due to the increasing cost, the missions that provide mobile platforms that can acquire data at multiple locations are becoming more attractive. Wheeled vehicles such as the MER rovers have proven extremely capable but have very limited range and cannot traverse rugged terrain. Flying vehicles such as balloons and airplanes have been proposed but are problematic due to the very thin atmospheric pressure and the strong, dusty winds present on Mars. The Center for Space Nuclear Research has designed an instrumented platform that can acquire detailed data at hundreds of locations during its lifetime - a Mars Hopper. The Mars Hopper concept utilizes energy from radioisotopic decay in a manner different from any existing radioisotopic power sources—as a thermal capacitor. By accumulating the heat from radioisotopic decay for long periods, the power of the source can be dramatically increased for short periods. The platform will be able to "hop" from one location to the next every 5-7 days with a separation of 5-10 km per hop. Preliminary designs show a platform that weighs around 52 kgs unfueled which is the condition at deployment. Consequently, several platforms may be deployed on a single launch from Earth. With sufficient lifetime, the entire surface of Mars can be mapped in detail by a couple dozen platforms. In addition, Hoppers can collect samples from all over the planet, including gorges, mountains and crevasses, and deliver them to a central location for eventual pick-up by a Mars Sample Return mission. The status of the Mars Hopper development project at the CSNR is discussed.

  11. Synthesis and Lanthanide Coordination Chemistry of Phosphine Oxide Decorated Dibenzothiophene and Dibenzothiophene Sulfone Platforms

    SciTech Connect (OSTI)

    Rosario-Amorin, Daniel; Ouizem, Sabrina; Dickie, D. A.; Paine, Robert T.; Cramer, Roger E.; Hay, Benjamin; Podair, Julien; Delmau, Laetitia Helene

    2014-01-01

    Syntheses for new ligands based upon dibenzothiophene and dibenzothiophene sulfone platforms, decorated with phosphine oxide and methylphosphine oxide donor groups, are described. Coordination chem. of 4, 6- bis(diphenylphosphinoylmethyl) dibenzothiophene (8) , 4, 6- bis(diphenylphosphinoylmethyl) dibenzothiophene- 5, 5- dioxide (9) and 4, 6- bis(diphenylphosphinoyl) dibenzothiophene- 5, 5- dioxide (10) with lanthanide nitrates, Ln(NO3) 3 (H2O) n is outlined, and crystal structure detns. reveal a range of chelation interactions on Ln(III) ions. The HNO3 dependence of the solvent extn. performance of 9 and 10 in 1, 2- dichloroethane for Eu(III) and Am(III) is described and compared against the extn. behavior of related dibenzofuran ligands (2, 3; R = Ph) and n- octyl(phenyl) - N, N- diisobutylcarbamoylmethyl phosphine oxide (4) measured under identical conditions.

  12. Cloud Computing for the Grid: GridControl: A Software Platform to Support the Smart Grid

    SciTech Connect (OSTI)

    2012-02-08

    GENI Project: Cornell University is creating a new software platform for grid operators called GridControl that will utilize cloud computing to more efficiently control the grid. In a cloud computing system, there are minimal hardware and software demands on users. The user can tap into a network of computers that is housed elsewhere (the cloud) and the network runs computer applications for the user. The user only needs interface software to access all of the cloud’s data resources, which can be as simple as a web browser. Cloud computing can reduce costs, facilitate innovation through sharing, empower users, and improve the overall reliability of a dispersed system. Cornell’s GridControl will focus on 4 elements: delivering the state of the grid to users quickly and reliably; building networked, scalable grid-control software; tailoring services to emerging smart grid uses; and simulating smart grid behavior under various conditions.

  13. Feasibility Study of Implementing a Mobile Collaborative Information Platform for International Safeguards Inspections

    SciTech Connect (OSTI)

    Gastelum, Zoe N.; Gitau, Ernest TN; Doehle, Joel R.; Toomey, Christopher M.

    2014-09-30

    In response to the growing pervasiveness of mobile technologies such as tablets and smartphones, the International Atomic Energy Agency and the U.S. Department of Energy National Laboratories have been exploring the potential use of these platforms for international safeguards activities. Specifically of interest are information systems (software, and accompanying servers and architecture) deployed on mobile devices to increase the situational awareness and productivity of an IAEA safeguards inspector in the field, while simultaneously reducing paperwork and pack weight of safeguards equipment. Exploratory development in this area has been met with skepticism regarding the ability to overcome technology deployment challenges for IAEA safeguards equipment. This report documents research conducted to identify potential challenges for the deployment of a mobile collaborative information system to the IAEA, and proposes strategies to mitigate those challenges.

  14. A Testing Platform for Validation of Overhead Conductor Aging Models and Understanding Thermal Limits

    SciTech Connect (OSTI)

    Irminger, Philip; Starke, Michael R; Dimitrovski, Aleksandar D; Young II, Marcus Aaron; Rizy, D Tom; Stovall, John P; Overholt, Philip N

    2014-01-01

    Power system equipment manufacturers and researchers continue to experiment with novel overhead electric conductor designs that support better conductor performance and address congestion issues. To address the technology gap in testing these novel designs, Oak Ridge National Laboratory constructed the Powerline Conductor Accelerated Testing (PCAT) facility to evaluate the performance of novel overhead conductors in an accelerated fashion in a field environment. Additionally, PCAT has the capability to test advanced sensors and measurement methods for accessing overhead conductor performance and condition. Equipped with extensive measurement and monitoring devices, PCAT provides a platform to improve/validate conductor computer models and assess the performance of novel conductors. The PCAT facility and its testing capabilities are described in this paper.

  15. Comparison of Second-Order Loads on a Tension-Leg Platform for Wind Turbines: Preprint

    SciTech Connect (OSTI)

    Gueydon, S.; Wuillaume, P.; Jonkman, J.; Robertson, A.; Platt, A.

    2015-03-01

    The first objective of this work is to compare the two floating offshore wind turbine simulation packages {DIFFRAC+aNySIM} and {WAMIT+FAST}. The focus is on second-order wave loads, and so first- and second-order wave loads are applied to a structure sequentially for a detailed comparison and a more precise analysis of the effects of the second-order loads. aNySIM does not have the capability to model flexible bodies, and so the simulations performed in this tool are done assuming a rigid body. FAST also assumes that the platform is rigid, but can account for the flexibility of the tower. The second objective is to study the effects of the second-order loads on the response of a TLP floating wind turbine. The flexibility of the tower must be considered for this investigation, and therefore only FAST is used.

  16. Computational and experimental platform for understanding and optimizing water flux and salt rejection in nanoporous membranes.

    SciTech Connect (OSTI)

    Rempe, Susan B.

    2010-09-01

    Affordable clean water is both a global and a national security issue as lack of it can cause death, disease, and international tension. Furthermore, efficient water filtration reduces the demand for energy, another national issue. The best current solution to clean water lies in reverse osmosis (RO) membranes that remove salts from water with applied pressure, but widely used polymeric membrane technology is energy intensive and produces water depleted in useful electrolytes. Furthermore incremental improvements, based on engineering solutions rather than new materials, have yielded only modest gains in performance over the last 25 years. We have pursued a creative and innovative new approach to membrane design and development for cheap desalination membranes by approaching the problem at the molecular level of pore design. Our inspiration comes from natural biological channels, which permit faster water transport than current reverse osmosis membranes and selectively pass healthy ions. Aiming for an order-of-magnitude improvement over mature polymer technology carries significant inherent risks. The success of our fundamental research effort lies in our exploiting, extending, and integrating recent advances by our team in theory, modeling, nano-fabrication and platform development. A combined theoretical and experimental platform has been developed to understand the interplay between water flux and ion rejection in precisely-defined nano-channels. Our innovative functionalization of solid state nanoporous membranes with organic protein-mimetic polymers achieves 3-fold improvement in water flux over commercial RO membranes and has yielded a pending patent and industrial interest. Our success has generated useful contributions to energy storage, nanoscience, and membrane technology research and development important for national health and prosperity.

  17. A Power Hardware-in-the-Loop Platform with Remote Distribution Circuit Cosimulation

    SciTech Connect (OSTI)

    Palmintier, Bryan; Lundstrom, Blake; Chakraborty, Sudipta; Williams, Tess L.; Schneider, Kevin P.; Chassin, David P.

    2015-04-01

    This paper demonstrates the use of a novel cosimulation architecture that integrates hardware testing using Power Hardware-in-the-Loop (PHIL) with larger-scale electric grid models using off-the-shelf, non-PHIL software tools. This architecture enables utilities to study the impacts of emerging energy technologies on their system and manufacturers to explore the interactions of new devices with existing and emerging devices on the power system, both without the need to convert existing grid models to a new platform or to conduct in-field trials. The paper describes an implementation of this architecture for testing two residential-scale advanced solar inverters at separate points of common coupling. The same hardware setup is tested with two different distribution feeders (IEEE 123 and 8500 node test systems) modeled using GridLAB-D. In addition to simplifying testing with multiple feeders, the architecture demonstrates additional flexibility with hardware testing in one location linked via the Internet to software modeling in a remote location. In testing, inverter current, real and reactive power, and PCC voltage are well captured by the co-simulation platform. Testing of the inverter advanced control features is currently somewhat limited by the software model time step (1 sec) and tested communication latency (24 msec). Overshoot induced oscillations are observed with volt/VAR control delays of 0 and 1.5 sec, while 3.4 sec and 5.5 sec delays produced little or no oscillation. These limitations could be overcome using faster modeling and communication within the same co-simulation architecture.

  18. The HARNESS Workbench: Unified and Adaptive Access to Diverse HPC Platforms

    SciTech Connect (OSTI)

    Sunderam, Vaidy S.

    2012-03-20

    The primary goal of the Harness WorkBench (HWB) project is to investigate innovative software environments that will help enhance the overall productivity of applications science on diverse HPC platforms. Two complementary frameworks were designed: one, a virtualized command toolkit for application building, deployment, and execution, that provides a common view across diverse HPC systems, in particular the DOE leadership computing platforms (Cray, IBM, SGI, and clusters); and two, a unified runtime environment that consolidates access to runtime services via an adaptive framework for execution-time and post processing activities. A prototype of the first was developed based on the concept of a 'system-call virtual machine' (SCVM), to enhance portability of the HPC application deployment process across heterogeneous high-end machines. The SCVM approach to portable builds is based on the insertion of toolkit-interpretable directives into original application build scripts. Modifications resulting from these directives preserve the semantics of the original build instruction flow. The execution of the build script is controlled by our toolkit that intercepts build script commands in a manner transparent to the end-user. We have applied this approach to a scientific production code (Gamess-US) on the Cray-XT5 machine. The second facet, termed Unibus, aims to facilitate provisioning and aggregation of multifaceted resources from resource providers and end-users perspectives. To achieve that, Unibus proposes a Capability Model and mediators (resource drivers) to virtualize access to diverse resources, and soft and successive conditioning to enable automatic and user-transparent resource provisioning. A proof of concept implementation has demonstrated the viability of this approach on high end machines, grid systems and computing clouds.

  19. Comparison of Unmanned Aerial Vehicle Platforms for Assessing Vegetation Cover in Sagebrush Steppe Ecosystems

    SciTech Connect (OSTI)

    Robert P. Breckenridge; Maxine Dakins; Stephen Bunting; Jerry Harbour; Sera White

    2011-09-01

    In this study, the use of unmanned aerial vehicles (UAVs) as a quick and safe method for monitoring biotic resources was evaluated. Vegetation cover and the amount of bare ground are important factors in understanding the sustainability of many ecosystems and assessment of rangeland health. Methods that improve speed and cost efficiency could greatly improve how biotic resources are monitored on western lands. Sagebrush steppe ecosystems provide important habitat for a variety of species (including sage grouse and pygmy rabbit). Improved methods are needed to support monitoring these habitats because there are not enough resource specialists or funds available for comprehensive ground evaluations. In this project, two UAV platforms, fixed wing and helicopter, were used to collect still-frame imagery to assess vegetation cover in sagebrush steppe ecosystems. This paper discusses the process for collecting and analyzing imagery from the UAVs to (1) estimate percent cover for six different vegetation types (shrub, dead shrub, grass, forb, litter, and bare ground) and (2) locate sage grouse using representative decoys. The field plots were located on the Idaho National Engineering (INL) site west of Idaho Falls, Idaho, in areas with varying amounts and types of vegetation cover. A software program called SamplePoint was used along with visual inspection to evaluate percent cover for the six cover types. Results were compared against standard field measurements to assess accuracy. The comparison of fixed-wing and helicopter UAV technology against field estimates shows good agreement for the measurement of bare ground. This study shows that if a high degree of detail and data accuracy is desired, then a helicopter UAV may be a good platform to use. If the data collection objective is to assess broad-scale landscape level changes, then the collection of imagery with a fixed-wing system is probably more appropriate.

  20. Method for crystal growth control

    DOE Patents [OSTI]

    Yates, Douglas A. (Burlington, MA); Hatch, Arthur E. (Waltham, MA); Goldsmith, Jeff M. (Medford, MA)

    1981-01-01

    The growth of a crystalline body of a selected material is controlled so that the body has a selected cross-sectional shape. The apparatus is of the type which includes the structure normally employed in known capillary die devices as well as means for observing at least the portion of the surfaces of the growing crystalline body and the meniscus (of melt material from which the body is being pulled) including the solid/liquid/vapor junction in a direction substantially perpendicular to the meniscus surface formed at the junction when the growth of the crystalline body is under steady state conditions. The cross-sectional size of the growing crystalline body can be controlled by determining which points exhibit a sharp change in the amount of reflected radiation of a preselected wavelength and controlling the speed at which the body is being pulled or the temperature of the growth pool of melt so as to maintain those points exhibiting a sharp change at a preselected spatial position relative to a predetermined reference position. The improvement comprises reference object means positioned near the solid/liquid/vapor junction and capable of being observed by the means for observing so as to define said reference position so that the problems associated with convection current jitter are overcome.

  1. What Hansel and Gretel’s Trail Teach Us about Knowledge Management

    SciTech Connect (OSTI)

    Wayne Simpson; Troy Hiltbrand

    2011-09-01

    Background At Idaho National Laboratory (INL), we are on the cusp of a significant era of change. INL is the lead Department of Energy Nuclear Research and Development Laboratory, focused on finding innovative solutions to the nation’s energy challenges. Not only has the Laboratory grown at an unprecedented rate over the last five years, but also has a significant segment of its workforce that is ready for retirement. Over the next 10 years, it is anticipated that upwards of 60% of the current workforce at INL will be eligible for retirement. Since the Laboratory is highly dependent on the intellectual capabilities of its scientists and engineers and their efforts to ensure the future of the nation’s energy portfolio, this attrition of resources has the potential of seriously impacting the ability of the Laboratory to sustain itself and the growth that it has achieved in the past years. Similar to Germany in the early nineteenth century, we face the challenge of our self-identity and must find a way to solidify our legacy to propel us into the future. Approach As the Brothers Grimm set out to collect their fairy tales, they focused on gathering information from the people that were most knowledgeable in the subject. For them, it was the peasants, with their rich knowledge of the region’s sub-culture of folk lore that was passed down from generation to generation around the evening fire. As we look to capture this tacit knowledge, it is requisite that we also seek this information from those individuals that are most versed in it. In our case, it is the scientists and researchers who have dedicated their lives to providing the nation with nuclear energy. This information comes in many forms, both digital and non-digital. Some of this information still resides in the minds of these scientists and researchers who are close to retirement, or who have already retired. Once the information has been collected, it has to be sorted through to identify where the “shining stones” can be found. The quantity of this information makes it improbable for an individual or set of individuals to sort through it and pick out those ideas which are most important. To accomplish both the step of information capture and classification, modern advancements in technology give us the tools that we need to successfully capture this tacit knowledge. To assist in this process, we have evaluated multiple tools and methods that will help us to unlock the power of tacit knowledge. Tools The first challenge that stands in the way of success is the capture of information. More than 50 years of nuclear research is captured in log books, microfiche, and other non-digital formats. To transform this information from its current form into a format that can “shine,” requires a number of different tools. These tools fall into three major categories: Information Capture, Content Retrieval, and Information Classification. Information Capture The first step is to capture the information from a myriad of sources. With knowledge existing in multiple formats, this step requires multiple approaches to be successful. Some of the sources that require consideration include handwritten documents, typed documents, microfiche, images, audio and video feeds, and electronic images. To make this step feasible for a large body of knowledge requires automation.

  2. Home Performance with ENERGY STAR -- 10 Years of Continued Growth...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Importance of the ENERGY STAR Brand * 84% of households recognized the ENERGY ... pollution and greenhouse gas emissions Brand, Platform, Network, and DOE Resources 12 ...

  3. D and D Knowledge Management Information Tool - 2012 - 12106

    SciTech Connect (OSTI)

    Upadhyay, H.; Lagos, L.; Quintero, W.; Shoffner, P.; DeGregory, J.

    2012-07-01

    Deactivation and decommissioning (D and D) work is a high priority activity across the Department of Energy (DOE) complex. Subject matter specialists (SMS) associated with the different ALARA (As-Low-As-Reasonably-Achievable) Centers, DOE sites, Energy Facility Contractors Group (EFCOG) and the D and D community have gained extensive knowledge and experience over the years in the cleanup of the legacy waste from the Manhattan Project. To prevent the D and D knowledge and expertise from being lost over time from the evolving and aging workforce, DOE and the Applied Research Center (ARC) at Florida International University (FIU) proposed to capture and maintain this valuable information in a universally available and easily usable system. D and D KM-IT provides single point access to all D and D related activities through its knowledge base. It is a community driven system. D and D KM-IT makes D and D knowledge available to the people who need it at the time they need it and in a readily usable format. It uses the World Wide Web as the primary source for content in addition to information collected from subject matter specialists and the D and D community. It brings information in real time through web based custom search processes and its dynamic knowledge repository. Future developments include developing a document library, providing D and D information access on mobile devices for the Technology module and Hotline, and coordinating multiple subject matter specialists to support the Hotline. The goal is to deploy a high-end sophisticated and secured system to serve as a single large knowledge base for all the D and D activities. The system consolidates a large amount of information available on the web and presents it to users in the simplest way possible. (authors)

  4. New Partners for Smart Growth Conference

    Broader source: Energy.gov [DOE]

    The New Partners for Smart Growth Conference is the nation's largest smart growth and sustainability conference. The three-day conference is themed, "Practical Tools and Innovative Strategies for Creating Great Communities."

  5. Energy and Interior Departments Host Offshore Energy Knowledge Exchange

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Workshop | Department of Energy and Interior Departments Host Offshore Energy Knowledge Exchange Workshop Energy and Interior Departments Host Offshore Energy Knowledge Exchange Workshop May 1, 2012 - 2:52pm Addthis This is an excerpt from the Second Quarter 2012 edition of the Wind Program R&D Newsletter. More than 150 experts on U.S. and European offshore renewable energy and the oil and gas industry met in Washington, D.C., on April 11 and 12 to exchange information and build

  6. Platform/foreslope facies and buildup geometry resulting from short-term and long-term eustatic sea level fluctuations: latemar buildup (Middle Triassic), Dolomites, northern Italy

    SciTech Connect (OSTI)

    Harris, M.T.; Goldhammer, R.

    1987-05-01

    Superimposed short-term and long-term eustatic sea level fluctuations directly controlled Latemar platform stratigraphy and indirectly influenced the deeper water facies and overall buildup geometry. Deeper water facies, the foreslope and toe of slope, are a function of platform submergence (highstand shedding) and subaerial exposure (lowstand lithification and erosion) and thus only indirectly reflect eustatic fluctuations. The Latemar consists of a platform core (3-4 km wide, 700 m thick) with a narrow margin, flanked by foreslope (30-35/sup 0/ dips), toe of slope, and basin deposits. The shallowing-upward platform sequence records a long-term (about 10 m.y.) eustatic sea level oscillation with an amplitude of about 150 m. The lower 250 m marks an initial catch-up phase (subtidal carbonates); the upper 450 m marks the sequential keep-up phase (meter-scale cyclic carbonates). These cycles record platform submergence and exposure caused by short-term (10/sup 4/-10/sup 5/ years) Milankovitch eustatic oscillations superimposed on the long-term trend. Platform submergence and exposure conditions result in contrasting foreslope deposits. During highstands, platform-derived sands bypass the foreslope, accumulating as toe-of-slope graded beds and basin turbidites. During lowstands, sand supply ceases, producing basin hard-grounds. Foreslope megabreccias contain margin-derived boundstone clasts, with only minor platform-derived sands (highstands) and lithified clasts (lowstands). As the platform margin/foreslope contact is nearly vertical, a progressively increasing volume of foreslope megabreccia was needed to maintain the depositional geometry. This coincides with the most commonly exposed platform interval, suggesting that platform exposure determines buildup flank geometry by controlling megabreccia clast production.

  7. April 5 PSERC Webinar: Seamless Bulk Electric Grid Management: A Platform for Designing the Next Generation EMS

    Broader source: Energy.gov [DOE]

    The DOE-funded Power Systems Engineering Research Center (PSERC) is offering a free public webinar that will address the feasibility of a flexible platform that is needed when designing the framework for the next generation Energy Management System (EMS) and analytics.

  8. Exploiting HPC Platforms for Metagenomics: Challenges and Opportunities (MICW - Metagenomics Informatics Challenges Workshop: 10K Genomes at a Time)

    ScienceCinema (OSTI)

    Canon, Shane [LBNL

    2013-01-22

    DOE JGI's Zhong Wang, chair of the High-performance Computing session, gives a brief introduction before Berkeley Lab's Shane Canon talks about "Exploiting HPC Platforms for Metagenomics: Challenges and Opportunities" at the Metagenomics Informatics Challenges Workshop held at the DOE JGI on October 12-13, 2011.

  9. Modeling delamination growth in composites

    SciTech Connect (OSTI)

    Reedy, E.D. Jr.; Mello, F.J.

    1996-12-01

    A method for modeling the initiation and growth of discrete delaminations in shell-like composite structures is presented. The laminate is divided into two or more sublaminates, with each sublaminate modeled with four-noded quadrilateral shell elements. A special, eight-noded hex constraint element connects opposing sublaminate shell elements. It supplies the nodal forces and moments needed to make the two opposing shell elements act as a single shell element until a prescribed failure criterion is satisfied. Once the failure criterion is attained, the connection is broken, creating or growing a discrete delamination. This approach has been implemented in a 3D finite element code. This code uses explicit time integration, and can analyze shell-like structures subjected to large deformations and complex contact conditions. The shell elements can use existing composite material models that include in-plane laminate failure modes. This analysis capability was developed to perform crashworthiness studies of composite structures, and is useful whenever there is a need to estimate peak loads, energy absorption, or the final shape of a highly deformed composite structure. This paper describes the eight-noded hex constraint element used to model the initiation and growth of a delamination, and discusses associated implementation issues. Particular attention is focused on the delamination growth criterion, and it is verified that calculated results do not depend on element size. In addition, results for double cantilever beam and end notched flexure specimens are presented and compared to measured data to assess the ability of the present approach to model a growing delamination.

  10. Search Method for Real-time Knowledge Discovery Modeled on the...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Search Method for Real-time Knowledge Discovery Modeled on the Human Brain Oak Ridge ... information processing properties of the human brain to computational knowledge discovery. ...

  11. Plenum type crystal growth process

    DOE Patents [OSTI]

    Montgomery, Kenneth E. (Tracy, CA)

    1992-01-01

    Crystals are grown in a tank which is divided by a baffle into a crystal growth region above the baffle and a plenum region below the baffle. A turbine blade or stirring wheel is positioned in a turbine tube which extends through the baffle to generate a flow of solution from the crystal growing region to the plenum region. The solution is pressurized as it flows into the plenum region. The pressurized solution flows back to the crystal growing region through return flow tubes extending through the baffle. Growing crystals are positioned near the ends of the return flow tubes to receive a direct flow of solution.

  12. Simulating Interface Growth and Defect Generation in CZT – Simulation State of the Art and Known Gaps

    SciTech Connect (OSTI)

    Henager, Charles H.; Gao, Fei; Hu, Shenyang Y.; Lin, Guang; Bylaska, Eric J.; Zabaras, Nicholas

    2012-11-01

    This one-year, study topic project will survey and investigate the known state-of-the-art of modeling and simulation methods suitable for performing fine-scale, fully 3-D modeling, of the growth of CZT crystals at the melt-solid interface, and correlating physical growth and post-growth conditions with generation and incorporation of defects into the solid CZT crystal. In the course of this study, this project will also identify the critical gaps in our knowledge of modeling and simulation techniques in terms of what would be needed to be developed in order to perform accurate physical simulations of defect generation in melt-grown CZT. The transformational nature of this study will be, for the first time, an investigation of modeling and simulation methods for describing microstructural evolution during crystal growth and the identification of the critical gaps in our knowledge of such methods, which is recognized as having tremendous scientific impacts for future model developments in a wide variety of materials science areas.

  13. Collaborative Knowledge Discovery & Marshalling for Intelligence & Security Applications

    SciTech Connect (OSTI)

    Cowell, Andrew J.; Jensen, Russell S.; Gregory, Michelle L.; Ellis, Peter C.; Fligg, Alan K.; McGrath, Liam R.; O'Hara, Kelly A.; Bell, Eric B.

    2010-05-24

    This paper discusses the Knowledge Encapsulation Framework, a flexible, extensible evidence-marshalling environment built upon a natural language processing pipeline and exposed to users via an open-source semantic wiki. We focus our discussion on applications of the framework to intelligence and security applications, specifically, an instantiation of the KEF environment for researching illicit trafficking in nuclear materials.

  14. ISPE: A knowledge-based system for fluidization studies

    SciTech Connect (OSTI)

    Reddy, S.

    1991-01-01

    Chemical engineers use mathematical simulators to design, model, optimize and refine various engineering plants/processes. This procedure requires the following steps: (1) preparation of an input data file according to the format required by the target simulator; (2) excecuting the simulation; and (3) analyzing the results of the simulation to determine if all specified goals'' are satisfied. If the goals are not met, the input data file must be modified and the simulation repeated. This multistep process is continued until satisfactory results are obtained. This research was undertaken to develop a knowledge based system, IPSE (Intelligent Process Simulation Environment), that can enhance the productivity of chemical engineers/modelers by serving as an intelligent assistant to perform a variety tasks related to process simulation. ASPEN, a widely used simulator by the US Department of Energy (DOE) at Morgantown Energy Technology Center (METC) was selected as the target process simulator in the project. IPSE, written in the C language, was developed using a number of knowledge-based programming paradigms: object-oriented knowledge representation that uses inheritance and methods, rulebased inferencing (includes processing and propagation of probabilistic information) and data-driven programming using demons. It was implemented using the knowledge based environment LASER. The relationship of IPSE with the user, ASPEN, LASER and the C language is shown in Figure 1.

  15. Apparatus for monitoring crystal growth

    DOE Patents [OSTI]

    Sachs, Emanual M. (Watertown, MA)

    1981-01-01

    A system and method are disclosed for monitoring the growth of a crystalline body from a liquid meniscus in a furnace. The system provides an improved human/machine interface so as to reduce operator stress, strain and fatigue while improving the conditions for observation and control of the growing process. The system comprises suitable optics for forming an image of the meniscus and body wherein the image is anamorphic so that the entire meniscus can be viewed with good resolution in both the width and height dimensions. The system also comprises a video display for displaying the anamorphic image. The video display includes means for enhancing the contrast between any two contrasting points in the image. The video display also comprises a signal averager for averaging the intensity of at least one preselected portions of the image. The value of the average intensity, can in turn be utilized to control the growth of the body. The system and method are also capable of observing and monitoring multiple processes.

  16. Method of monitoring crystal growth

    DOE Patents [OSTI]

    Sachs, Emanual M. (Watertown, MA)

    1982-01-01

    A system and method are disclosed for monitoring the growth of a crystalline body from a liquid meniscus in a furnace. The system provides an improved human/machine interface so as to reduce operator stress, strain and fatigue while improving the conditions for observation and control of the growing process. The system comprises suitable optics for forming an image of the meniscus and body wherein the image is anamorphic so that the entire meniscus can be viewed with good resolution in both the width and height dimensions. The system also comprises a video display for displaying the anamorphic image. The video display includes means for enhancing the contrast between any two contrasting points in the image. The video display also comprises a signal averager for averaging the intensity of at least one preselected portions of the image. The value of the average intensity, can in turn be utilized to control the growth of the body. The system and method are also capable of observing and monitoring multiple processes.

  17. The United States after the great recession: the challenge of sustainable growth

    SciTech Connect (OSTI)

    Meltzer, Joshua

    2013-02-15

    The paper outlines the strengths and weaknesses of the U.S. economic growth model, assesses its’ ability to respond to the key economic, environmental and social challenges currently facing the U.S. and proposes policies that if adopted would move the U.S. onto a more sustainable growth path. The paper provides scenarios of projected future growth trajectories, as well as recommendations for specific policies in key areas: employment, infrastructure, energy and fiscal rebalancing. To reach this goal this paper focuses on four areas for action: Increasing employment, which is the most urgent priority to accelerate recovery from the Great Recession, while addressing underlying structural issues that have led to a decade of poor economic outcomes for most citizens; Investing in the future, as the key marker of whether the United States is prepared to make farsighted decisions to improve education, build new infrastructure and increase innovation; Maximizing an increased energy endowment in a way that grows the economy, while reinforcing the trend towards reducing resource demand and reducing greenhouse gas emissions; and, Fiscal rebalancing, where the United States must insulate economic recovery from the process of fiscal reform while reducing and stabilizing debt over the long term. Finally, we argue that President Obama can re-energize America’s global leadership if he builds on a platform of domestic actions that enhance the sustainability of America’s society and economy.

  18. Korea's Green Growth Strategy: Mitigating Climate Change and...

    Open Energy Info (EERE)

    Korea's Green Growth Strategy: Mitigating Climate Change and Developing New Growth Engines Jump to: navigation, search Name Korea's Green Growth Strategy: Mitigating Climate Change...

  19. Stochastic response analysis of tension leg platform: A statistical quadratization and cubicization approach

    SciTech Connect (OSTI)

    Kareem, A.; Zhao, J.

    1994-12-31

    The nonlinearities in the wind and wave loadings of compliant offshore platforms and in their structural characteristics result in response statistics that deviate from a Gaussian distribution. This paper focuses on the analysis of the response of these structures to random nonlinear wind and wave loads. As an improvement over the commonly used linearization approach an equivalent statistical quadratization (ESQ) and cubicization (ESC) approach is presented. The nonlinear loading or structural characteristics can be expressed in terms of an equivalent polynomial that contains terms up to quadratic or cubic depending on the type of nonlinearity. The response statistics and its cumulants are based on Volterra theory. A direct integration scheme is utilized to evaluate the response cumulants. The results provide a good comparison with simulation. It is noted that the ESQ provides an accurate description of the systems with asymmetrical nonlinearities, whereas, for symmetrical nonlinearities the ESC provides a good representation. Based on the information on higher-order cumulants, the response pdf, crossing rates and peak value distributions can be derived.

  20. Monitoring system including an electronic sensor platform and an interrogation transceiver

    DOE Patents [OSTI]

    Kinzel, Robert L.; Sheets, Larry R.

    2003-09-23

    A wireless monitoring system suitable for a wide range of remote data collection applications. The system includes at least one Electronic Sensor Platform (ESP), an Interrogator Transceiver (IT) and a general purpose host computer. The ESP functions as a remote data collector from a number of digital and analog sensors located therein. The host computer provides for data logging, testing, demonstration, installation checkout, and troubleshooting of the system. The IT transmits signals from one or more ESP's to the host computer to the ESP's. The IT host computer may be powered by a common power supply, and each ESP is individually powered by a battery. This monitoring system has an extremely low power consumption which allows remote operation of the ESP for long periods; provides authenticated message traffic over a wireless network; utilizes state-of-health and tamper sensors to ensure that the ESP is secure and undamaged; has robust housing of the ESP suitable for use in radiation environments; and is low in cost. With one base station (host computer and interrogator transceiver), multiple ESP's may be controlled at a single monitoring site.

  1. Optimization of Sparse Matrix-Vector Multiplication on Emerging Multicore Platforms

    SciTech Connect (OSTI)

    Williams, Samuel; Oliker, Leonid; Vuduc, Richard; Shalf, John; Yelick, Katherine; Demmel, James

    2008-10-16

    We are witnessing a dramatic change in computer architecture due to the multicore paradigm shift, as every electronic device from cell phones to supercomputers confronts parallelism of unprecedented scale. To fully unleash the potential of these systems, the HPC community must develop multicore specific-optimization methodologies for important scientific computations. In this work, we examine sparse matrix-vector multiply (SpMV) - one of the most heavily used kernels in scientific computing - across a broad spectrum of multicore designs. Our experimental platform includes the homogeneous AMD quad-core, AMD dual-core, and Intel quad-core designs, the heterogeneous STI Cell, as well as one of the first scientific studies of the highly multithreaded Sun Victoria Falls (a Niagara2 SMP). We present several optimization strategies especially effective for the multicore environment, and demonstrate significant performance improvements compared to existing state-of-the-art serial and parallel SpMV implementations. Additionally, we present key insights into the architectural trade-offs of leading multicore design strategies, in the context of demanding memory-bound numerical algorithms.

  2. Optimization of a Lattice Boltzmann Computation on State-of-the-Art Multicore Platforms

    SciTech Connect (OSTI)

    Williams, Samuel; Carter, Jonathan; Oliker, Leonid; Shalf, John; Yelick, Katherine

    2009-04-10

    We present an auto-tuning approach to optimize application performance on emerging multicore architectures. The methodology extends the idea of search-based performance optimizations, popular in linear algebra and FFT libraries, to application-specific computational kernels. Our work applies this strategy to a lattice Boltzmann application (LBMHD) that historically has made poor use of scalar microprocessors due to its complex data structures and memory access patterns. We explore one of the broadest sets of multicore architectures in the HPC literature, including the Intel Xeon E5345 (Clovertown), AMD Opteron 2214 (Santa Rosa), AMD Opteron 2356 (Barcelona), Sun T5140 T2+ (Victoria Falls), as well as a QS20 IBM Cell Blade. Rather than hand-tuning LBMHD for each system, we develop a code generator that allows us to identify a highly optimized version for each platform, while amortizing the human programming effort. Results show that our auto-tuned LBMHD application achieves up to a 15x improvement compared with the original code at a given concurrency. Additionally, we present detailed analysis of each optimization, which reveal surprising hardware bottlenecks and software challenges for future multicore systems and applications.

  3. Model Development and Loads Analysis of a Wind Turbine on a Floating Offshore Tension Leg Platform

    SciTech Connect (OSTI)

    Matha, D.; Fischer, T.; Kuhn, M.; Jonkman, J.

    2010-02-01

    This report presents results of the analysis of a 5-MW wind turbine located on a floating offshore tension leg platform (TLP) that was conducted using the fully coupled time-domain aero-hydro-servo-elastic design code FAST with AeroDyn and HydroDyn. Models in this code are of greater fidelity than most of the models that have been used to analyze floating turbines in the past--which have neglected important hydrodynamic and mooring system effects. The report provides a description of the development process of a TLP model, which is a modified version of a Massachusetts Institute of Technology design derived from a parametric linear frequency-domain optimization process. An extensive loads and stability analysis for ultimate and fatigue loads according to the procedure of the International Electrotechnical Commission offshore wind turbine design standard was performed with the verified TLP model. Response statistics, extreme event tables, fatigue lifetimes, and selected time histories of design-driving extreme events are analyzed and presented. Loads for the wind turbine on the TLP are compared to those of an equivalent land-based turbine in terms of load ratios. Major instabilities for the TLP are identified and described.

  4. Well having inhibited microbial growth

    DOE Patents [OSTI]

    Lee, Brady D.; Dooley, Kirk J.

    2006-08-15

    The invention includes methods of inhibiting microbial growth in a well. A packing material containing a mixture of a first material and an antimicrobial agent is provided to at least partially fill a well bore. One or more access tubes are provided in an annular space around a casing within the well bore. The access tubes have a first terminal opening located at or above a ground surface and have a length that extends from the first terminal opening at least part of the depth of the well bore. The access tubes have a second terminal opening located within the well bore. An antimicrobial material is supplied into the well bore through the first terminal opening of the access tubes. The invention also includes well constructs.

  5. Controlled growth of semiconductor crystals

    DOE Patents [OSTI]

    Bourret-Courchesne, E.D.

    1992-07-21

    A method is disclosed for growth of III-V, II-VI and related semiconductor single crystals that suppresses random nucleation and sticking of the semiconductor melt at the crucible walls. Small pieces of an oxide of boron B[sub x]O[sub y] are dispersed throughout the comminuted solid semiconductor charge in the crucible, with the oxide of boron preferably having water content of at least 600 ppm. The crucible temperature is first raised to a temperature greater than the melt temperature T[sub m1] of the oxide of boron (T[sub m1]=723 K for boron oxide B[sub 2]O[sub 3]), and the oxide of boron is allowed to melt and form a reasonably uniform liquid layer between the crucible walls and bottom surfaces and the still-solid semiconductor charge. The temperature is then raised to approximately the melt temperature T[sub m2] of the semiconductor charge material, and crystal growth proceeds by a liquid encapsulated, vertical gradient freeze process. About half of the crystals grown have a dislocation density of less than 1000/cm[sup 2]. If the oxide of boron has water content less than 600 ppm, the crucible material should include boron nitride, a layer of the inner surface of the crucible should be oxidized before the oxide of boron in the crucible charge is melted, and the sum of thicknesses of the solid boron oxide layer and liquid boron oxide layer should be at least 50 [mu]m. 7 figs.

  6. Controlled growth of semiconductor crystals

    DOE Patents [OSTI]

    Bourret-Courchesne, Edith D. (Richmond, CA)

    1992-01-01

    A method for growth of III-V, II-VI and related semiconductor single crystals that suppresses random nucleation and sticking of the semiconductor melt at the crucible walls. Small pieces of an oxide of boron B.sub.x O.sub.y are dispersed throughout the comminuted solid semiconductor charge in the crucible, with the oxide of boron preferably having water content of at least 600 ppm. The crucible temperature is first raised to a temperature greater than the melt temperature T.sub.m1 of the oxide of boron (T.sub.m1 =723.degree. K. for boron oxide B.sub.2 O.sub.3), and the oxide of boron is allowed to melt and form a reasonably uniform liquid layer between the crucible walls and bottom surfaces and the still-solid semiconductor charge. The temperature is then raised to approximately the melt temperature T.sub.m2 of the semiconductor charge material, and crystal growth proceeds by a liquid encapsulated, vertical gradient freeze process. About half of the crystals grown have a dislocation density of less than 1000/cm.sup.2. If the oxide of boron has water content less than 600 ppm, the crucible material should include boron nitride, a layer of the inner surface of the crucible should be oxidized before the oxide of boron in the crucible charge is melted, and the sum of thicknesses of the solid boron oxide layer and liquid boron oxide layer should be at least 50 .mu.m.

  7. Biofuel Distribution Datasets from the Bioenergy Knowledge Discovery Framework

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The Bioenergy Knowledge Discovery Framework invites users to discover the power of bioenergy through an interface that provides extensive access to research data and literature, GIS mapping tools, and collaborative networks. The Bioenergy KDF supports efforts to develop a robust and sustainable bioenergy industry. The KDF facilitates informed decision making by providing a means to synthesize, analyze, and visualize vast amounts of information in a relevant and succinct manner. It harnesses Web 2.0 and social networking technologies to build a collective knowledge system that can better examine the economic and environmental impacts of development options for biomass feedstock production, biorefineries, and related infrastructure. [copied from https://www.bioenergykdf.net/content/about] Holdings include datasets, models, and maps and the collections are growing due to both DOE contributions and individuals' data uploads.

  8. Feedstock Logistics Datasets from DOE's Bioenergy Knowledge Discovery Framework (KDF)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The Bioenergy Knowledge Discovery Framework invites users to discover the power of bioenergy through an interface that provides extensive access to research data and literature, GIS mapping tools, and collaborative networks. The Bioenergy KDF supports efforts to develop a robust and sustainable bioenergy industry. The KDF facilitates informed decision making by providing a means to synthesize, analyze, and visualize vast amounts of information in a relevant and succinct manner. It harnesses Web 2.0 and social networking technologies to build a collective knowledge system that can better examine the economic and environmental impacts of development options for biomass feedstock production, biorefineries, and related infrastructure. Holdings include datasets, models, and maps. [from https://www.bioenergykdf.net/content/about

  9. Biofuel Production Datasets from DOE's Bioenergy Knowledge Discovery Framework (KDF)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The Bioenergy Knowledge Discovery Framework invites users to discover the power of bioenergy through an interface that provides extensive access to research data and literature, GIS mapping tools, and collaborative networks. The Bioenergy KDF supports efforts to develop a robust and sustainable bioenergy industry. The KDF facilitates informed decision making by providing a means to synthesize, analyze, and visualize vast amounts of information in a relevant and succinct manner. It harnesses Web 2.0 and social networking technologies to build a collective knowledge system that can better examine the economic and environmental impacts of development options for biomass feedstock production, biorefineries, and related infrastructure. [copied from https://www.bioenergykdf.net/content/about]

    Holdings include datasets, models, and maps and the collections arel growing due to both DOE contributions and data uploads from individuals.

  10. Feedstock Production Datasets from the Bioenergy Knowledge Discovery Framework

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The Bioenergy Knowledge Discovery Framework invites users to discover the power of bioenergy through an interface that provides extensive access to research data and literature, GIS mapping tools, and collaborative networks. The Bioenergy KDF supports efforts to develop a robust and sustainable bioenergy industry. The KDF facilitates informed decision making by providing a means to synthesize, analyze, and visualize vast amounts of information in a relevant and succinct manner. It harnesses Web 2.0 and social networking technologies to build a collective knowledge system that can better examine the economic and environmental impacts of development options for biomass feedstock production, biorefineries, and related infrastructure. [copied from https://www.bioenergykdf.net/content/about] Holdings include datasets, models, and maps and the collections are growing due to both DOE contributions and data uploads from individuals.

  11. Essential Body of Knowledge (EBK) | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Train12.jpg The OCIO has developed a DOE-specific Essential Body of Knowledge (EBK) using DOE cybersecurity policy, industry best practices and lessons learned, and comprehensive internal needs assessments to identify fundamental cybersecurity roles and associated responsibilities. Core competencies, as identified and documented in the EBK, represent the 'core' skill set required of cybersecurity professionals to competently fill their roles. The OCIO has determined the following to be key cyber

  12. A knowledge based model of electric utility operations. Final report

    SciTech Connect (OSTI)

    1993-08-11

    This report consists of an appendix to provide a documentation and help capability for an analyst using the developed expert system of electric utility operations running in CLIPS. This capability is provided through a separate package running under the WINDOWS Operating System and keyed to provide displays of text, graphics and mixed text and graphics that explain and elaborate on the specific decisions being made within the knowledge based expert system.

  13. Capturing and Using Knowledge about the Use of Visualization Toolkits

    SciTech Connect (OSTI)

    Del Rio, Nicholas R.; Pinheiro da Silva, Paulo

    2012-11-02

    When constructing visualization pipelines using toolkits such as Visualization Toolkit (VTK) and Generic Mapping Tools (GMT), developers must understand (1) what toolkit operators will transform their data from its raw state to some required view state and (2) what viewers are available to present the generated view. Traditionally, developers learn about how to construct visualization pipelines by reading documentation and inspecting code examples, which can be costly in terms of the time and effort expended. Once an initial pipeline is constructed, developers may still have to undergo a trial and error process before a satisfactory visualization is generated. This paper presents the Visualization Knowledge Project (VisKo) that is built on a knowledge base of visualization toolkit operators and how they can be piped together to form visualization pipelines. Developers may now rely on VisKo to guide them when constructing visualization pipelines and in some cases, when VisKo has complete knowledge about some set of operators (i.e., sequencing and parameter settings), automatically generate a fully functional visualization pipeline.

  14. Pesticide use knowledge and practices: A gender differences in Nepal

    SciTech Connect (OSTI)

    Atreya, Kishor . E-mail: k.atreya@gmail.com

    2007-06-15

    It is important to understand gender difference on pesticide use knowledge, attitude and practices for identifying pesticide risks by gender and to recommend more gender-sensitive programs. However, very few studies have been conducted so far in Nepal. This study, thus, interviewed a total of 325 males and 109 females during 2005 to assess gender differences on pesticide use knowledge, attitude and practices. More than 50% females had never been to school and only <8% individuals were found trained in Integrated Pest Management (IPM). Almost all males and females did not smoke, drink and eat during pesticides application and also believed that pesticides are harmful to human health, livestock, plant diversity and their environment. However, there were gender differences on household decision on pesticides to be used (p<0.001), care of wind direction during spraying (p=0.032), prior knowledge on safety measures (p=0.016), reading and understanding of pesticides labels (p<0.001), awareness of the labels (p<0.001) and protective covers. Almost all respondents were aware of negative impacts of pesticide use on human health and environment irrespective of gender; however, females were at higher risk due to lower level of pesticide use safety and awareness. It is strongly recommended to initiate gender-sensitive educational and awareness activities, especially on pesticide use practices and safety precautions.

  15. Agent-Based Knowledge Discovery for Modeling and Simulation

    SciTech Connect (OSTI)

    Haack, Jereme N.; Cowell, Andrew J.; Marshall, Eric J.; Fligg, Alan K.; Gregory, Michelle L.; McGrath, Liam R.

    2009-09-15

    This paper describes an approach to using agent technology to extend the automated discovery mechanism of the Knowledge Encapsulation Framework (KEF). KEF is a suite of tools to enable the linking of knowledge inputs (relevant, domain-specific evidence) to modeling and simulation projects, as well as other domains that require an effective collaborative workspace for knowledge-based tasks. This framework can be used to capture evidence (e.g., trusted material such as journal articles and government reports), discover new evidence (covering both trusted and social media), enable discussions surrounding domain-specific topics and provide automatically generated semantic annotations for improved corpus investigation. The current KEF implementation is presented within a semantic wiki environment, providing a simple but powerful collaborative space for team members to review, annotate, discuss and align evidence with their modeling frameworks. The novelty in this approach lies in the combination of automatically tagged and user-vetted resources, which increases user trust in the environment, leading to ease of adoption for the collaborative environment.

  16. Synthetic heparin-binding growth factor analogs

    DOE Patents [OSTI]

    Pena, Louis A.; Zamora, Paul; Lin, Xinhua; Glass, John D.

    2007-01-23

    The invention provides synthetic heparin-binding growth factor analogs having at least one peptide chain that binds a heparin-binding growth factor receptor, covalently bound to a hydrophobic linker, which is in turn covalently bound to a non-signaling peptide that includes a heparin-binding domain. The synthetic heparin-binding growth factor analogs are useful as soluble biologics or as surface coatings for medical devices.

  17. VP 100: Growth in solar means growth in Ohio | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Growth in solar means growth in Ohio VP 100: Growth in solar means growth in Ohio October 6, 2010 - 10:57am Addthis DuPont is betting on major growth in the market for solar energy -- and therefore for its Tedlar film, a durable backing for silicon solar panels. | Photo Courtesy of DuPont DuPont is betting on major growth in the market for solar energy -- and therefore for its Tedlar film, a durable backing for silicon solar panels. | Photo Courtesy of DuPont Lorelei Laird Writer, Energy

  18. RPF: An Extensible, Cross-Platform, Binary File Format for Radiation Physics Data

    SciTech Connect (OSTI)

    Ham, C L

    2002-09-10

    Lawrence Livermore National Laboratory's Radiation Technology Group (RTG) uses a number of computer codes for simulation and analysis of radiation data. The number of incompatible data formats that these data presented themselves in have continued to multiply. In the 1980's a Common Data Format (CDF, see Appendix A) was devised for internal use by the RTG. This format represented a single gamma-ray spectrum as ASCII energy/count pairs preceded by an ASCII header. The ASCII representation of the data assured that it was compatible on any computing platform and this format is still in use. In the mid 1990's it became apparent that instrument systems of greater complexity would demand a file format of larger capacity to support systems then on the drawing board, including networks of sensors collecting time series of gamma-ray spectra. These systems were in the planning stage and defined data structures were not available. It became apparent that a new storage format for nuclear measurements data would be needed and it would have to be flexible and extensible to accommodate the requirements of systems of the future. As part of an LDRD, we began to investigate what others were doing, especially in the high-energy physics community, to deal with the large volumes of data being generated. Of particular interest was the very general Hierarchical Data Format (HDF), developed and maintained by the National Center for Supercomputing Applications (NCSA), that we ultimately used to develop the Radiation Physics Format (RPF). The HDF subroutine library provides users with the ability to customize a data file format based on standard calls to the HDF subroutine library. The RPF was developed and deployed on Sun and Hewlett-Packard workstations running their proprietary versions of UNIX.

  19. F3D Image Processing and Analysis for Many - and Multi-core Platforms

    SciTech Connect (OSTI)

    2014-10-01

    F3D is written in OpenCL, so it achieve[sic] platform-portable parallelism on modern mutli-core CPUs and many-core GPUs. The interface and mechanims to access F3D core are written in Java as a plugin for Fiji/ImageJ to deliver several key image-processing algorithms necessary to remove artifacts from micro-tomography data. The algorithms consist of data parallel aware filters that can efficiently utilizes[sic] resources and can work on out of core datasets and scale efficiently across multiple accelerators. Optimizing for data parallel filters, streaming out of core datasets, and efficient resource and memory and data managements over complex execution sequence of filters greatly expedites any scientific workflow with image processing requirements. F3D performs several different types of 3D image processing operations, such as non-linear filtering using bilateral filtering and/or median filtering and/or morphological operators (MM). F3D gray-level MM operators are one-pass constant time methods that can perform morphological transformations with a line-structuring element oriented in discrete directions. Additionally, MM operators can be applied to gray-scale images, and consist of two parts: (a) a reference shape or structuring element, which is translated over the image, and (b) a mechanism, or operation, that defines the comparisons to be performed between the image and the structuring element. This tool provides a critical component within many complex pipelines such as those for performing automated segmentation of image stacks. F3D is also called a "descendent" of Quant-CT, another software we developed in the past. These two modules are to be integrated in a next version. Further details were reported in: D.M. Ushizima, T. Perciano, H. Krishnan, B. Loring, H. Bale, D. Parkinson, and J. Sethian. Structure recognition from high-resolution images of ceramic composites. IEEE International Conference on Big Data, October 2014.

  20. Design of the SLAC RCE Platform: A General Purpose ATCA Based Data Acquisition System

    SciTech Connect (OSTI)

    Herbst, R.; Claus, R.; Freytag, M.; Haller, G.; Huffer, M.; Maldonado, S.; Nishimura, K.; O'Grady, C.; Panetta, J.; Perazzo, A.; Reese, B.; Ruckman, L.; Thayer, J. G.; Weaver, M.

    2015-01-23

    The SLAC RCE platform is a general purpose clustered data acquisition system implemented on a custom ATCA compliant blade, called the Cluster On Board (COB). The core of the system is the Reconfigurable Cluster Element (RCE), which is a system-on-chip design based upon the Xilinx Zynq family of FPGAs, mounted on custom COB daughter-boards. The Zynq architecture couples a dual core ARM Cortex A9 based processor with a high performance 28nm FPGA. The RCE has 12 external general purpose bi-directional high speed links, each supporting serial rates of up to 12Gbps. 8 RCE nodes are included on a COB, each with a 10Gbps connection to an on-board 24-port Ethernet switch integrated circuit. The COB is designed to be used with a standard full-mesh ATCA backplane allowing multiple RCE nodes to be tightly interconnected with minimal interconnect latency. Multiple shelves can be clustered using the front panel 10-gbps connections. The COB also supports local and inter-blade timing and trigger distribution. An experiment specific Rear Transition Module adapts the 96 high speed serial links to specific experiments and allows an experiment-specific timing and busy feedback connection. This coupling of processors with a high performance FPGA fabric in a low latency, multiple node cluster allows high speed data processing that can be easily adapted to any physics experiment. RTEMS and Linux are both ported to the module. The RCE has been used or is the baseline for several current and proposed experiments (LCLS, HPS, LSST, ATLAS-CSC, LBNE, DarkSide, ILC-SiD, etc).

  1. OpenMSI: A High-Performance Web-Based Platform for Mass Spectrometry Imaging

    SciTech Connect (OSTI)

    Rubel, Oliver; Greiner, Annette; Cholia, Shreyas; Louie, Katherine; Bethel, E. Wes; Northen, Trent R.; Bowen, Benjamin P.

    2013-10-02

    Mass spectrometry imaging (MSI) enables researchers to directly probe endogenous molecules directly within the architecture of the biological matrix. Unfortunately, efficient access, management, and analysis of the data generated by MSI approaches remain major challenges to this rapidly developing field. Despite the availability of numerous dedicated file formats and software packages, it is a widely held viewpoint that the biggest challenge is simply opening, sharing, and analyzing a file without loss of information. Here we present OpenMSI, a software framework and platform that addresses these challenges via an advanced, high-performance, extensible file format and Web API for remote data access (http://openmsi.nersc.gov). The OpenMSI file format supports storage of raw MSI data, metadata, and derived analyses in a single, self-describing format based on HDF5 and is supported by a large range of analysis software (e.g., Matlab and R) and programming languages (e.g., C++, Fortran, and Python). Careful optimization of the storage layout of MSI data sets using chunking, compression, and data replication accelerates common, selective data access operations while minimizing data storage requirements and are critical enablers of rapid data I/O. The OpenMSI file format has shown to provide >2000-fold improvement for image access operations, enabling spectrum and image retrieval in less than 0.3 s across the Internet even for 50 GB MSI data sets. To make remote high-performance compute resources accessible for analysis and to facilitate data sharing and collaboration, we describe an easy-to-use yet powerful Web API, enabling fast and convenient access to MSI data, metadata, and derived analysis results stored remotely to facilitate high-performance data analysis and enable implementation of Web based data sharing, visualization, and analysis.

  2. "Conflict Between Economic Growth and Environmental Protection...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9, 2012, 4:15pm Colloquia MBG Auditorium "Conflict Between Economic Growth and Environmental Protection", Dr. Bryan Czech, resident, Center for the Advancement of the Steady State...

  3. GROWTH AND ELECTROCHEMICAL CHARACTERIZATION OF CARBON NANOSPIKE...

    Office of Scientific and Technical Information (OSTI)

    Title: GROWTH AND ELECTROCHEMICAL CHARACTERIZATION OF CARBON NANOSPIKE THIN FILM ELECTRODES Authors: Sheridan, Leah B 1 ; Hensley, Dale K 1 ; Lavrik, Nickolay V 1 ; Smith, ...

  4. Sandia Energy - Biomimetic Approach to Nanoparticle Growth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    biological growth, a new 'Extended LaMer' method for reproducible and predictable synthesis of nanoparticles was developed. Significance and Impact This general approach allows...

  5. Examining System-Wide Impacts of Solar PV Control Systems with a Power Hardware-in-the-Loop Platform

    SciTech Connect (OSTI)

    Williams, Tess L.; Fuller, Jason C.; Schneider, Kevin P.; Palmintier, Bryan; Lundstrom, Blake; Chakraborty, Sudipta

    2014-10-11

    High penetration levels of distributed solar PV power generation can lead to adverse power quality impacts such as excessive voltage rise, voltage flicker, and reactive power values that result in unacceptable voltage levels. Advanced inverter control schemes have been proposed that have the potential to mitigate many power quality concerns. However, closed-loop control may lead to unintended behavior in deployed systems as complex interactions can occur between numerous operating devices. In order to enable the study of the performance of advanced control schemes in a detailed distribution system environment, a Hardware-in-the-Loop (HIL) platform has been developed. In the HIL system, GridLAB-D, a distribution system simulation tool, runs in real-time mode at the Pacific Northwest National Laboratory (PNNL) and supplies power system parameters at a point of common coupling to hardware located at the National Renewable Energy Laboratory (NREL). Hardware inverters interact with grid and PV simulators emulating an operational distribution system and power output from the inverters is measured and sent to PNNL to update the real-time distribution system simulation. The platform is described and initial test cases are presented. The platform is used to study the system-wide impacts and the interactions of controls applied to inverters that are integrated into a simulation of the IEEE 8500-node test feeder, with inverters in either constant power factor control or active volt/VAR control. We demonstrate that this HIL platform is well-suited to the study of advanced inverter controls and their impacts on the power quality of a distribution feeder. Additionally, the results from HIL are used to validate GridLAB-D simulations of advanced inverter controls. ?

  6. SU-E-T-376: 3-D Commissioning for An Image-Guided Small Animal Micro- Irradiation Platform

    SciTech Connect (OSTI)

    Qian, X; Wuu, C; Admovics, J

    2014-06-01

    Purpose: A 3-D radiochromic plastic dosimeter has been used to cross-test the isocentricity of a high resolution image-guided small animal microirradiation platform. In this platform, the mouse stage rotating for cone beam CT imaging is perpendicular to the gantry rotation for sub-millimeter radiation delivery. A 3-D dosimeter can be used to verify both imaging and irradiation coordinates. Methods: A 3-D dosimeter and optical CT scanner were used in this study. In the platform, both mouse stage and gantry can rotate 360° with rotation axis perpendicular to each other. Isocentricity and coincidence of mouse stage and gantry rotations were evaluated using star patterns. A 3-D dosimeter was placed on mouse stage with center at platform isocenter approximately. For CBCT isocentricity, with gantry moved to 90°, the mouse stage rotated horizontally while the x-ray was delivered to the dosimeter at certain angles. For irradiation isocentricity, the gantry rotated 360° to deliver beams to the dosimeter at certain angles for star patterns. The uncertainties and agreement of both CBCT and irradiation isocenters can be determined from the star patterns. Both procedures were repeated 3 times using 3 dosimeters to determine short-term reproducibility. Finally, dosimeters were scanned using optical CT scanner to obtain the results. Results: The gantry isocentricity is 0.9 ± 0.1 mm and mouse stage rotation isocentricity is about 0.91 ± 0.11 mm. Agreement between the measured isocenters of irradiation and imaging coordinates was determined. The short-term reproducibility test yielded 0.5 ± 0.1 mm between the imaging isocenter and the irradiation isocenter, with a maximum displacement of 0.7 ± 0.1 mm. Conclusion: The 3-D dosimeter can be very useful in precise verification of targeting for a small animal irradiation research. In addition, a single 3-D dosimeter can provide information in both geometric and dosimetric uncertainty, which is crucial for translational studies.

  7. Assessment of US shipbuilding current capability to build a commercial OTEC platform and a cold water pipe

    SciTech Connect (OSTI)

    Komelasky, M. C.

    1980-03-01

    Lowry and Hoffman Associates Inc. (LHA) performed for ORI an analysis of the shipbuilding requirements for constructing an OTEC plant, and the available shipyard assets which could fulfill these requirements. In addition, several shipyards were queried concerning their attitudes towards OTEC. In assessing the shipbuilding requirements for an OTEC plant, four different platform configurations were studied and four different designs of the cold water pipe (CWP) were examined. The platforms were: a concrete ship design proposed by Lockheed; concrete spar designs with internal heat exchangers (IHE) (Rosenblatt) and external heat exchangers (XHE) (Lockheed); and a steel ship design proposed by Gibbs and Cox. The types of materials examined for CWP construction were: steel, fiber reinforced plastic (FPR), elastomer, and concrete. The report is organized io three major discussion areas. All the construction requirements are synthesized for the four platforms and CWPs, and general comments are made concerning their availability in the US. Specific shipbuilders facilities are reviewed for their applicability to building an OTEC plant, an assessment of the shipyards general interest in the OTEC program is presented providing an insight into their nearterm commercial outlook. The method of determining this interest will depend largely on a risk analysis of the OTEC system. Also included are factors which may comprise this analysis, and a methodology to ascertain the risk. In the appendices, various shipyard specifications are presented, shipyard assessment matrices are given, graphs of various shipyard economic outlooks are provided, and definitions of the risk factors are listed. (WHK)

  8. Digital electronic bone growth stimulator

    DOE Patents [OSTI]

    Kronberg, J.W.

    1993-01-01

    The present invention relates to the electrical treatment of biological tissue. In particular, the present invention discloses a device that produces discrete electrical pulse trains for treating osteoporosis and accelerating bone growth. According to its major aspects and broadly stated, the present invention consists of an electrical circuit configuration capable of generating Bassett-type waveforms shown with alternative signals provide for the treatment of either fractured bones or osteoporosis. The signal generator comprises a quartz clock, an oscillator circuit, a binary divider chain, and a plurality of simple, digital logic gates. Signals are delivered efficiently, with little or no distortion, and uniformly distributed throughout the area of injury. Perferably, power is furnished by widely available and inexpensive radio batteries, needing replacement only once in several days. The present invention can be affixed to a medical cast without a great increase in either weight or bulk. Also, the disclosed stimulator can be used to treat osteoporosis or to strengthen a healing bone after the cast has been removed by attaching the device to the patient`s skin or clothing.

  9. Numerical Prediction of Experimentally Observed Behavior of a Scale Model of an Offshore Wind Turbine Supported by a Tension-Leg Platform: Preprint

    SciTech Connect (OSTI)

    Prowell, I.; Robertson, A.; Jonkman, J.; Stewart, G. M.; Goupee, A. J.

    2013-01-01

    Realizing the critical importance the role physical experimental tests play in understanding the dynamics of floating offshore wind turbines, the DeepCwind consortium conducted a one-fiftieth-scale model test program where several floating wind platforms were subjected to a variety of wind and wave loading condition at the Maritime Research Institute Netherlands wave basin. This paper describes the observed behavior of a tension-leg platform, one of three platforms tested, and the systematic effort to predict the measured response with the FAST simulation tool using a model primarily based on consensus geometric and mass properties of the test specimen.

  10. Narrowing the gap between the promise and reality of polyketide synthases as a synthetic biology platform

    SciTech Connect (OSTI)

    Poust, S; Hagen, A; Katz, L; Keasling, JD

    2014-12-01

    Engineering modular polyketide synthases (PKSs) has the potential to be an effective methodology to produce existing and novel chemicals. However, this potential has only just begun to be realized. We propose the adoption of an iterative design-build-test-learn paradigm to improve PKS engineering. We suggest methods to improve engineered PKS design by learning from laboratory-based selection; adoption of DNA design software and automation to build constructs and libraries more easily; tools for the expression of engineered proteins in a variety of heterologous hosts; and mass spectrometry-based high-throughput screening methods. Finally, lessons learned during iterations of the design-build-test-learn cycle can serve as a knowledge base for the development of a single retrosynthesis algorithm usable by both PKS experts and non-experts alike.

  11. Knowledge Management at the Fast Flux Test Facility

    SciTech Connect (OSTI)

    Wootan, David W.; Omberg, Ronald P.

    2013-06-01

    One of the goals of the Department of Energy’s Office of Nuclear Energy, initiated under the Fuel Cycle Research and Development Program (FCRD) and continued under the Advanced Reactor Concepts Program (ARC) is to preserve the knowledge that has been gained in the United States on Liquid Metal Reactors (LMRs) that could support the development of an environmentally and economically sound nuclear fuel cycle. The Fast Flux Test Facility (FFTF) is the most recent LMR to operate in the United States, from 1982 to 1992, and was designed as a fully instrumented test reactor with on-line, real time test control and performance monitoring of components and tests installed in the reactor. The 10 years of operation of the FFTF provided a very useful framework for testing the advances in LMR safety technology based on passive safety features that may be of increased importance to new designs after the events at Fukushima. Knowledge preservation at the FFTF is focused on the areas of design, construction, and startup of the reactor, as well as on preserving information obtained from 10 years of successful operating history and extensive irradiation testing of fuels and materials. In order to ensure protection of information at risk, the program to date has sequestered reports, files, tapes, and drawings to allow for secure retrieval. The FFTF knowledge management program includes a disciplined and orderly approach to respond to client’s requests for documents and data in order to minimize the search effort and ensure that future requests for this information can be readily accommodated.

  12. Listeriosis Prevention Knowledge Among Pregnant Women in the USA

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ogunmodede, Folashade; Jones, Jeffery L.; Scheftel, Joni; Kirkland, Elizabeth; Schulkin, Jay; Lynfield, Ruth

    2005-01-01

    Background: Listeriosis is a food-borne disease often associated with ready-to-eat foods. It usually causes mild febrile gastrointestinal illness in immunocompetent persons. In pregnant women, it may cause more severe infection and often crosses the placenta to infect the fetus, resulting in miscarriage, fetal death or neonatal morbidity. Simple precautions during pregnancy can prevent listeriosis. However, many women are unaware of these precautions and listeriosis education is often omitted from prenatal care. Methods: Volunteer pregnant women were recruited to complete a questionnaire to assess their knowledge of listeriosis and its prevention, in two separate studies. One study was a nationalmore » survey of 403 women from throughout the USA, and the other survey was limited to 286 Minnesota residents. Results: In the multi-state survey, 74 of 403 respondents (18%) had some knowledge of listeriosis, compared with 43 of 286 (15%) respondents to the Minnesota survey. The majority of respondents reported hearing about listeriosis from a medical professional. In the multi-state survey, 33% of respondents knew listeriosis could be prevented by not eating delicatessen meats, compared with 17% in the Minnesota survey ( p = 0.01). Similarly, 31% of respondents to the multi-state survey compared with 19% of Minnesota survey respondents knew listeriosis could be prevented by avoiding unpasteurized dairy products (p = 0.05). As for preventive behaviors, 18% of US and 23% of Minnesota respondents reported avoiding delicatessen meats and ready-to-eat foods during pregnancy, whereas 86% and 88%, respectively, avoided unpasteurized dairy products. Conclusions: Most pregnant women have limited knowledge of listeriosis prevention. Even though most respondents avoided eating unpasteurized dairy products, they were unaware of the risk associated with ready-to-eat foods. Improved education of pregnant women regarding the risk and sources of listeriosis in pregnancy is needed.« less

  13. The Oil and Natural Gas Knowledge Management Database from NETL

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The Knowledge Management Database (KMD) Portal provides four options for searching the documents and data that NETL-managed oil and gas research has produced over the years for DOE’s Office of Fossil Energy. Information includes R&D carried out under both historical and ongoing DOE oil and gas research and development (R&D). The Document Repository, the CD/DVD Library, the Project Summaries from 1990 to the present, and the Oil and Natural Gas Program Reference Shelf provide a wide range of flexibility and coverage.

  14. The Oil and Natural Gas Knowledge Management Database from NETL

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The Knowledge Management Database (KMD) Portal provides four options for searching the documents and data that NETL-managed oil and gas research has produced over the years for DOE’s Office of Fossil Energy. Information includes R&D carried out under both historical and ongoing DOE oil and gas research and development (R&D). The Document Repository, the CD/DVD Library, the Project Summaries from 1990 to the present, and the Oil and Natural Gas Program Reference Shelf provide a wide range of flexibility and coverage.

  15. APBF-DEC NOx Adsorber/DPF Project: SUV / Pick-up Truck Platform

    SciTech Connect (OSTI)

    Webb, C; Weber, P; Thornton,M

    2003-08-24

    The objective of this project is to determine the influence of diesel fuel composition on the ability of NOX adsorber catalyst (NAC) technology, in conjunction with diesel particle filters (DPFs), to achieve stringent emissions levels with a minimal fuel economy impact. The test bed for this project was intended to be a light-duty sport utility vehicle (SUV) with a goal of achieving light-duty Tier 2-Bin 5 tail pipe emission levels (0.07 g/mi. NOX and 0.01 g/mi. PM). However, with the current US market share of light-duty diesel applications being so low, no US 2002 model year (MY) light-duty truck (LDT) or SUV platforms equipped with a diesel engine and having a gross vehicle weight rating (GVWR) less than 8500 lb exist. While the current level of diesel engine use is relatively small in the light-duty class, there exists considerable potential for the diesel engine to gain a much larger market share in the future as manufacturers of heavy light-duty trucks (HLDTs) attempt to offset the negative impact on cooperate average fuel economy (CAFE) that the recent rise in market share of the SUVs and LDTs has caused. The US EPA Tier 2 emission standards also contain regulation to prevent the migration of heavy light-duty trucks and SUV's to the medium duty class. This preventive measure requires that all medium duty trucks, SUV's and vans in the 8,500 to 10,000 lb GVWR range being used as passenger vehicles, meet light-duty Tier 2 standards. In meeting the Tier 2 emission standards, the HLDTs and medium-duty passenger vehicles (MDPVs) will face the greatest technological challenges. Because the MDPV is the closest weight class and application relative to the potential upcoming HLDTs and SUV's, a weight class compromise was made in this program to allow the examination of using a diesel engine with a NAC-DPF system on a 2002 production vehicle. The test bed for this project is a 2500 series Chevrolet Silverado equipped with a 6.6L Duramax diesel engine certified to 2002 MY Federal heavy-duty and 2002 MY California medium-duty emission standards. The stock vehicle included cooled air charge (CAC), turbocharger (TC), direct fuel injection (DFI), oxidation catalyst (OC), and exhaust gas recirculation (EGR)

  16. F3D Image Processing and Analysis for Many - and Multi-core Platforms

    Energy Science and Technology Software Center (OSTI)

    2014-10-01

    F3D is written in OpenCL, so it achieve[sic] platform-portable parallelism on modern mutli-core CPUs and many-core GPUs. The interface and mechanims to access F3D core are written in Java as a plugin for Fiji/ImageJ to deliver several key image-processing algorithms necessary to remove artifacts from micro-tomography data. The algorithms consist of data parallel aware filters that can efficiently utilizes[sic] resources and can work on out of core datasets and scale efficiently across multiple accelerators. Optimizingmore » for data parallel filters, streaming out of core datasets, and efficient resource and memory and data managements over complex execution sequence of filters greatly expedites any scientific workflow with image processing requirements. F3D performs several different types of 3D image processing operations, such as non-linear filtering using bilateral filtering and/or median filtering and/or morphological operators (MM). F3D gray-level MM operators are one-pass constant time methods that can perform morphological transformations with a line-structuring element oriented in discrete directions. Additionally, MM operators can be applied to gray-scale images, and consist of two parts: (a) a reference shape or structuring element, which is translated over the image, and (b) a mechanism, or operation, that defines the comparisons to be performed between the image and the structuring element. This tool provides a critical component within many complex pipelines such as those for performing automated segmentation of image stacks. F3D is also called a "descendent" of Quant-CT, another software we developed in the past. These two modules are to be integrated in a next version. Further details were reported in: D.M. Ushizima, T. Perciano, H. Krishnan, B. Loring, H. Bale, D. Parkinson, and J. Sethian. Structure recognition from high-resolution images of ceramic composites. IEEE International Conference on Big Data, October 2014.« less

  17. New Report Highlights Growth of America's Clean Energy Job Sector |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean Energy Job Sector August 23, 2012 - 12:20pm Addthis New Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean

  18. Biofuel Enduse Datasets from the Bioenergy Knowledge Discovery Framework (KDF)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The Bioenergy Knowledge Discovery Framework invites users to discover the power of bioenergy through an interface that provides extensive access to research data and literature, GIS mapping tools, and collaborative networks. The Bioenergy KDF supports efforts to develop a robust and sustainable bioenergy industry. The KDF facilitates informed decision making by providing a means to synthesize, analyze, and visualize vast amounts of information in a relevant and succinct manner. It harnesses Web 2.0 and social networking technologies to build a collective knowledge system that can better examine the economic and environmental impacts of development options for biomass feedstock production, biorefineries, and related infrastructure. [copied from https://www.bioenergykdf.net/content/about]

    Holdings include datasets, models, and maps. This is a very new resource, but the collections will grow due to both DOE contributions and individualsÆ data uploads. Currently the Biofuel Enduse collection includes 133 items. Most of these are categorized as literature, but 36 are listed as datasets and ten as models.

  19. Knowledge Preservation at the Fast Flux Test Facility

    SciTech Connect (OSTI)

    Wootan, David W.; Omberg, Ronald P.

    2011-12-30

    One of the goals of the Department of Energy's Office of Nuclear Energy Fuel Cycle Research and Development Program (FCRD) is to preserve the knowledge that has been gained in the United States on Liquid Metal Reactors (LMRs) that could support the development of an environmentally and economically sound nuclear fuel cycle. The Fast Flux Test Facility (FFTF) is the most recent LMR to operate in the United States, from 1982 to 1992, and was designed as a fully instrumented test reactor with on-line, real time test control and performance monitoring of components and tests installed in the reactor. Knowledge preservation at the FFTF is focused on the areas of design, construction, and startup of the reactor, as well as on preserving information obtained from 10 years of successful operating history and extensive irradiation testing of fuels and materials. In order to ensure protection of information at risk, the program to date has sequestered reports, files, tapes, and drawings to allow for secure retrieval. A disciplined and orderly approach has been developed to respond to client's requests for documents and data in order to minimize the search effort and ensure that future requests for this information can be readily accommodated.

  20. Biofuel Enduse Datasets from the Bioenergy Knowledge Discovery Framework (KDF)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The Bioenergy Knowledge Discovery Framework invites users to discover the power of bioenergy through an interface that provides extensive access to research data and literature, GIS mapping tools, and collaborative networks. The Bioenergy KDF supports efforts to develop a robust and sustainable bioenergy industry. The KDF facilitates informed decision making by providing a means to synthesize, analyze, and visualize vast amounts of information in a relevant and succinct manner. It harnesses Web 2.0 and social networking technologies to build a collective knowledge system that can better examine the economic and environmental impacts of development options for biomass feedstock production, biorefineries, and related infrastructure. [copied from https://www.bioenergykdf.net/content/about]

    Holdings include datasets, models, and maps. This is a very new resource, but the collections will grow due to both DOE contributions and individualsÆ data uploads. Currently the Biofuel Enduse collection includes 133 items. Most of these are categorized as literature, but 36 are listed as datasets and ten as models.

  1. III-V/Si on silicon-on-insulator platform for hybrid nanoelectronics

    SciTech Connect (OSTI)

    Prucnal, Slawomir Zhou, Shengqiang; Ou, Xin; Facsko, Stefan; Oskar Liedke, Maciej; Bregolin, Felipe; Liedke, Bartosz; Grebing, Jochen; Fritzsche, Monika; Hübner, Rene; Mücklich, Arndt; Rebohle, Lars; Skorupa, Wolfgang; Helm, Manfred; Turek, Marcin; Drozdziel, Andrzej

    2014-02-21

    The unique properties of SOI wafers enable the integration of heterogeneous materials with distinct functionalities in different layers. In particular, III-V compound semiconductors are very attractive for low-noise and high-speed electronic and photonic components integrated on a single chip. We have developed a CMOS compatible and fully integrated solution for the integration of III-V compound semiconductors with silicon technology for optoelectronic applications. InAs compound semiconductor nanostructures are synthesized in SOI wafers using the combined ion beam implantation and millisecond liquid-phase epitaxial growth. Optoelectronic and microstructural investigations carried out on implanted, annealed, and selectively etched samples confirm the formation of high-quality III-V compound semiconductor nanostructures.

  2. Soybean Knowledge Base (SoyKB): a Web Resource for Soybean Translation...

    Office of Scientific and Technical Information (OSTI)

    Soybean Knowledge Base (SoyKB): a Web Resource for Soybean Translational Genomics Citation Details In-Document Search Title: Soybean Knowledge Base (SoyKB): a Web Resource for ...

  3. Platform Li-Ion Battery Risk Assessment Tool: Cooperative Research and Development Final Report, CRADA Number CRD-10-407

    SciTech Connect (OSTI)

    Smith, K.

    2012-01-01

    Creare was awarded a Phase 1 STTR contract from the US Office of Naval Research, with a seven month period of performance from 6/28/2010 to 1/28/2011. The objectives of the STTR were to determine the feasibility of developing a software package for estimating reliability of battery packs, and develop a user interface to allow the designer to assess the overall impact on battery packs and host platforms for cell-level faults. NREL served as sub-tier partner to Creare, providing battery modeling and battery thermal safety expertise.

  4. Highly efficient greenish-blue platinum-based phosphorescent organic light-emitting diodes on a high triplet energy platform

    SciTech Connect (OSTI)

    Chang, Y. L. Gong, S. White, R.; Lu, Z. H.; Wang, X.; Wang, S.; Yang, C.

    2014-04-28

    We have demonstrated high-efficiency greenish-blue phosphorescent organic light-emitting diodes (PHOLEDs) based on a dimesitylboryl-functionalized C^N chelate Pt(II) phosphor, Pt(m-Bptrz)(t-Bu-pytrz-Me). Using a high triplet energy platform and optimized double emissive zone device architecture results in greenish-blue PHOLEDs that exhibit an external quantum efficiency of 24.0% and a power efficiency of 55.8?lm/W. This record high performance is comparable with that of the state-of-the-art Ir-based sky-blue organic light-emitting diodes.

  5. Knowledge-based sizing of cogeneration plant in buildings

    SciTech Connect (OSTI)

    Williams, J.M.; Griffiths, A.J.; Knight, I.P.

    1998-10-01

    Cogeneration is now accepted as a cost-effective and environmentally friendly means of meeting some of a building`s heating and power needs. Cogeneration plants have been installed in many buildings throughout the United Kingdom. Because of commercial pressures, building owners and cogeneration companies are keen to reduce the time and money involved in sizing units, and a decision support tool has been developed to aid the engineer in selecting the unit size. An initial assessment of the sizing can be made with only knowledge of the building`s type, size, and location, which enables the model to be used in new build situations. For an existing building, the accuracy of the predictions can then be progressively improved by providing more information about the building`s energy use, enabling the optimum unit to be identified. This paper briefly describes the model and demonstrates its use through an example feasibility study.

  6. A Zero Knowledge Protocol For Nuclear Warhead Verification

    SciTech Connect (OSTI)

    Glaser, Alexander; Goldston, Robert J.

    2014-03-14

    The verification of nuclear warheads for arms control faces a paradox: International inspectors must gain high confidence in the authenticity of submitted items while learning nothing about them. Conventional inspection systems featuring ''information barriers'', designed to hide measurments stored in electronic systems, are at risk of tampering and snooping. Here we show the viability of fundamentally new approach to nuclear warhead verification that incorporates a zero-knowledge protocol, designed such that sensitive information is never measured so does not need to be hidden. We interrogate submitted items with energetic neutrons, making in effect, differential measurements of neutron transmission and emission. Calculations of diversion scenarios show that a high degree of discrimination can be achieved while revealing zero information. Timely demonstration of the viability of such an approach could be critical for the nexxt round of arms-control negotiations, which will likely require verification of individual warheads, rather than whole delivery systems.

  7. Design Principles for Effective Knowledge Discovery from Big Data

    SciTech Connect (OSTI)

    Begoli, Edmon; Horey, James L

    2012-01-01

    Big data phenomenon refers to the practice of collection and processing of very large data sets and associated systems and algorithms used to analyze these massive datasets. Architectures for big data usually range across multiple machines and clusters, and they commonly consist of multiple special purpose sub-systems. Coupled with the knowledge discovery process, big data movement offers many unique opportunities for organizations to benefit (with respect to new insights, business optimizations, etc.). However, due to the difficulty of analyzing such large datasets, big data presents unique systems engineering and architectural challenges. In this paper, we present three sys- tem design principles that can inform organizations on effective analytic and data collection processes, system organization, and data dissemination practices. The principles presented derive from our own research and development experiences with big data problems from various federal agencies, and we illustrate each principle with our own experiences and recommendations.

  8. Geothermal Energy Growth Continues, Industry Survey Reports

    Broader source: Energy.gov [DOE]

    A survey released by the Geothermal Energy Association (GEA) shows continued growth in the number of new geothermal power projects under development in the United States, a 20% increase since January of this year.

  9. EM-21 Retrieval Knowledge Center: Waste Retrieval Challenges

    SciTech Connect (OSTI)

    Fellinger, Andrew P.; Rinker, Michael W.; Berglin, Eric J.; Minichan, Richard L.; Poirier, Micheal R.; Gauglitz, Phillip A.; Martin, Bruce A.; Hatchell, Brian K.; Saldivar, Eloy; Mullen, O Dennis; Chapman, Noel F.; Wells, Beric E.; Gibbons, Peter W.

    2009-04-10

    EM-21 is the Waste Processing Division of the Office of Engineering and Technology, within the U.S. Department of Energy’s (DOE) Office of Environmental Management (EM). In August of 2008, EM-21 began an initiative to develop a Retrieval Knowledge Center (RKC) to provide the DOE, high level waste retrieval operators, and technology developers with centralized and focused location to share knowledge and expertise that will be used to address retrieval challenges across the DOE complex. The RKC is also designed to facilitate information sharing across the DOE Waste Site Complex through workshops, and a searchable database of waste retrieval technology information. The database may be used to research effective technology approaches for specific retrieval tasks and to take advantage of the lessons learned from previous operations. It is also expected to be effective for remaining current with state-of-the-art of retrieval technologies and ongoing development within the DOE Complex. To encourage collaboration of DOE sites with waste retrieval issues, the RKC team is co-led by the Savannah River National Laboratory (SRNL) and the Pacific Northwest National Laboratory (PNNL). Two RKC workshops were held in the Fall of 2008. The purpose of these workshops was to define top level waste retrieval functional areas, exchange lessons learned, and develop a path forward to support a strategic business plan focused on technology needs for retrieval. The primary participants involved in these workshops included retrieval personnel and laboratory staff that are associated with Hanford and Savannah River Sites since the majority of remaining DOE waste tanks are located at these sites. This report summarizes and documents the results of the initial RKC workshops. Technology challenges identified from these workshops and presented here are expected to be a key component to defining future RKC-directed tasks designed to facilitate tank waste retrieval solutions.

  10. Driving Economic Growth: Advanced Technology Vehicles Manufacturing |

    Office of Environmental Management (EM)

    Department of Energy Driving Economic Growth: Advanced Technology Vehicles Manufacturing Driving Economic Growth: Advanced Technology Vehicles Manufacturing With $8 billion in loans and commitments to projects that have supported the production of more than 4 million fuel-efficient cars and more than 35,000 direct jobs across eight states, the Advanced Technology Vehicles Manufacturing (ATVM) loan program has played a key role in helping the American auto industry propel the resurgence of

  11. Biomass Scenario Model: BETO Analysis Platform Peer Review; NREL (National Renewable Energy Laboratory)

    SciTech Connect (OSTI)

    Bush, B.

    2015-03-23

    The Biomass Scenario Model (BSM) is a unique, carefully validated, state-of-the-art fourth-generation model of the domestic bioenergy supply chain which explicitly focuses on policy issues and their potential side effects. It integrates resource availability, behavior, policy, and physical, technological, and economic constraints. The BSM uses system-dynamics simulation to model dynamic interactions across the supply chain; it tracks the deployment of biofuels given technological development and the reaction of the investment community to those technologies in the context of land availability, the competing oil market, consumer demand for biofuels, and government policies over time. It places a strong emphasis on the behavior and decision-making of various economic agents. The model treats the major infrastructure-compatible fuels. Scenario analysis based on the BSM shows that the biofuels industry tends not to rapidly thrive without significant external actions in the early years of its evolution. An initial focus for jumpstarting the industry typically has strongest results in the BSM in areas where effects of intervention have been identified to be multiplicative. In general, we find that policies which are coordinated across the whole supply chain have significant impact in fostering the growth of the biofuels industry and that the production of tens of billions of gallons of biofuels may occur under sufficiently favorable conditions.

  12. Middle Triassic paleokarst surfaces and associated stratigraphic patterns in platform carbonates: Evidence from sedimentology and diagenesis, southern Alps, Italy

    SciTech Connect (OSTI)

    Mutti, M.; Jadoul, F. )

    1991-03-01

    Triassic carbonate platforms are superbly exposed in the Southern Alps. A regional paleokarst surface occurs in the Middle Triassic, at the Ladinian-Carnian stage boundary, and is well recognized throughout the Tethyan region. The authors describe the characteristics of the paleokarst and the stratigraphic patterns of the strata deposited immediately after the formation of the surface in the Brembana Valley. The paleokarst cuts up to tens of meters into the underlying Esino Limestone massive platform facies and forms a lens-shaped depression filled by peritidal cyclic facies intensively deformed in tepees. The origin of this geometry can be explained either as a tectonic-controlled feature or as a karst-processes related incised-valley associated to a major eustatic cycle. Depression-filling peritidal facies are intensively deformed in senile tepees and are periodically interbedded with 'terra rossa' soils and tend to pinchout at the margins of the depression. Several orders of cyclicity are recognized in peritidal carbonates. Diagenetic features are exceptionally complex and record a wide variety of superimposing environments ranging from normal marine to early meteoric and can be related to major cyclic stratigraphic patterns. Syndepositional cements form up to 80% of the present rock.

  13. Development of the CD Symcap platform to study gas-shell mix in implosions at the National Ignition Facility

    SciTech Connect (OSTI)

    Casey, D. T.; Smalyuk, V. A.; Tipton, R. E.; Pino, J. E.; Remington, B. A.; Rowley, D. P.; Weber, S. V.; Barrios, M.; Benedetti, L. R.; Bleuel, D. L.; Bond, E. J.; Bradley, D. K.; Caggiano, J. A.; Callahan, D. A.; Cerjan, C. J.; Edwards, M. J.; Fittinghoff, D.; Glenn, S.; Haan, S. W.; Hamza, A.; and others

    2014-09-15

    Surrogate implosions play an important role at the National Ignition Facility (NIF) for isolating aspects of the complex physical processes associated with fully integrated ignition experiments. The newly developed CD Symcap platform has been designed to study gas-shell mix in indirectly driven, pure T{sub 2}-gas filled CH-shell implosions equipped with 4 ?m thick CD layers. This configuration provides a direct nuclear signature of mix as the DT yield (above a characterized D contamination background) is produced by D from the CD layer in the shell, mixing into the T-gas core. The CD layer can be placed at different locations within the CH shell to probe the depth and extent of mix. CD layers placed flush with the gas-shell interface and recessed up to 8??m have shown that most of the mix occurs at the inner-shell surface. In addition, time-gated x-ray images of the hotspot show large brightly radiating objects traversing through the hotspot around bang-time, which are likely chunks of CH/CD plastic. This platform is a powerful new capability at the NIF for understanding mix, one of the key performance issues for ignition experiments.

  14. Developing a Millifluidic Platform for the Synthesis of Ultrasmall Nanoclusters: Ultrasmall Copper Nanoclusters as a Case Study

    SciTech Connect (OSTI)

    Biswas, Sanchita [Louisiana State Univ., Baton Rouge, LA (United States). Center for Advanced Microstructures and Devices and Center for Atomic-level Catalysts Design; Miller, Jeffrey T. [Argonne National Lab. (ANL), Argonne, IL (United States); Li, Yuehao [Louisiana State Univ., Baton Rouge, LA (United States). Cain Dept. of Chemical Engineering; Nandakumar, Krishnaswamy [Louisiana State Univ., Baton Rouge, LA (United States). Cain Dept. of Chemical Engineering; Kumar, Challa S.S.R. [Louisiana State Univ., Baton Rouge, LA (United States). Center for Advanced Microstructures and Devices and Center for Atomic-level Catalysts Design

    2012-02-02

    The future of lab-on-a-chip devices for the synthesis of nanomaterials hinges on the successful development of high-throughput methods with better control over their size. While significant effort in this direction mainly focuses on developing “difficult to fabricate” complex microfluidic reactors, scant attention has been paid to the “easy to fabricate” and simple millifluidic systems that could provide the required control as well as high throughput. By utilizing numerical simulation of fluids within the millifluidic space at different flow rates, the results presented here show velocity profiles and residence time distributions similar to the case of microfluidics. By significantly reducing the residence time and residence time distribution, a continuous flow synthesis of ultrasmall copper nanoclusters (UCNCs) with exceptional colloidal stability is achieved. In-situ synchrotron-radiation-based X-ray absorption spectroscopy (XAS) reveal that the as-prepared clusters are about 1 nm, which is further supported by transmission electron microscopy and UV–vis spectroscopy studies. The clusters reported here are the smallest ever produced using a lab-on-a-chip platform. When supported on silica, they are found to efficiently catalyze C–H oxidation reactions, hitherto unknown to be catalyzed by Cu. This work suggests that a millifluidic platform can be an inexpensive, versatile, easy-to-use, and powerful tool for nanoparticle synthesis in general, and more specifically for ultrasmall nanoclusters (UNCs).

  15. Poly(dimethylsiloxane) microchip-based immunoassay with multiple reaction zones: Toward on-chip multiplex detection platform

    SciTech Connect (OSTI)

    Shao, Guocheng; Wang, Jun; Li, Zhaohui; Saraf, Laxmikant V.; Wang, Wanjun; Lin, Yuehe

    2011-09-20

    In this work, a poly(dimethylsiloxane) (PDMS) microchip-based immuno-sensing platform with integrated pneumatic micro valves is described. The microchip was fabricated with multiple layer soft lithography technology. By controlling the activation status of corresponding valves, reagent flows in the microchannel network can be well manipulated so that immuno-reactions only take place at designated reaction zones (DRZs). Four DRZs are included in the prototype microchip. Since these DRZs are all isolated from each other by micro valves, cross contamination is prevented. Using the inner surface of the all-PDMS microchannel as immunoassay substrate, on-chip sandwich format solid phase immunoassay was performed to demonstrate the feasibility of this immuno-sensing platform. Mouse IgG and fluorescein isothiocyanate (FITC) were used as the model analyte and the signal reporter respectively. Only 10 ul sample is needed for the assay and low detection limit of 5 ng/ml (?33 pM) was achieved though low-cost polyclonal antibodies were used in our experiment for feasibility study only. The encouraging results from mouse IgG immunoassay proved the feasibility of our microchip design. With slight modification of the assay protocol, the same chip design can be used for multi-target detection and can provide a simple, cost-effective and integrated microchip solution for multiplex immunoassay applications.

  16. Development of the CD symcap platform to study gas-shell mix in implosions at the National Ignition Facility

    SciTech Connect (OSTI)

    Casey, D. T.; Smalyuk, V. A.; Tipton, R. E.; Pino, J. E.; Grim, G. P.; Remington, B. A.; Rowley, D. P.; Weber, S. V.; Barrios, M.; Benedetti, L. R.; Bleuel, D. L.; Bond, E. J.; Bradley, D. K.; Caggiano, J. A.; Callahan, D. A.; Cerjan, C. J.; Chen, K. C.; Edgell, D. H.; Edwards, M. J.; Fittinghoff, D.; Frenje, J. A.; Gatu-Johnson, M.; Glebov, V. Y.; Glenn, S.; Guler, N.; Haan, S. W.; Hamza, A.; Hatarik, R.; Herrmann, H. W.; Hoover, D.; Hsing, W. W.; Izumi, N.; Kervin, P.; Khan, S.; Kilkenny, J. D.; Kline, J.; Knauer, J.; Kyrala, G.; Landen, O. L.; Ma, T.; MacPhee, A. G.; McNaney, J. M.; Mintz, M.; Moore, A.; Nikroo, A.; Pak, A.; Parham, T.; Petrasso, R.; Rinderknecht, H. G.; Sayre, D. B.; Schneider, M.; Stoeffl, W.; Tommasini, R.; Town, R. P.; Widmann, K.; Wilson, D. C.; Yeamans, C. B.

    2014-09-09

    Surrogate implosions play an important role at the National Ignition Facility (NIF) for isolating aspects of the complex physical processes associated with fully integrated ignition experiments. The newly developed CD Symcap platform has been designed to study gas-shell mix in indirectly driven, pure T?-gas filled CH-shell implosions equipped with 4 ?m thick CD layers. This configuration provides a direct nuclear signature of mix as the DT yield (above a characterized D contamination background) is produced by D from the CD layer in the shell, mixing into the T-gas core. The CD layer can be placed at different locations within the CH shell to probe the depth and extent of mix. CD layers placed flush with the gas-shell interface and recessed up to 8 ?m have shown that most of the mix occurs at the inner-shell surface. In addition, time-gated x-ray images of the hotspot show large brightly-radiating objects traversing through the hotspot around bang-time, which are likely chunks of CH/CD plastic. This platform is a powerful new capability at the NIF for understanding mix, one of the key performance issues for ignition experiments.

  17. Development of the CD symcap platform to study gas-shell mix in implosions at the National Ignition Facility

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Casey, D. T.; Smalyuk, V. A.; Tipton, R. E.; Pino, J. E.; Grim, G. P.; Remington, B. A.; Rowley, D. P.; Weber, S. V.; Barrios, M.; Benedetti, L. R.; et al

    2014-09-09

    Surrogate implosions play an important role at the National Ignition Facility (NIF) for isolating aspects of the complex physical processes associated with fully integrated ignition experiments. The newly developed CD Symcap platform has been designed to study gas-shell mix in indirectly driven, pure T₂-gas filled CH-shell implosions equipped with 4 ÎŒm thick CD layers. This configuration provides a direct nuclear signature of mix as the DT yield (above a characterized D contamination background) is produced by D from the CD layer in the shell, mixing into the T-gas core. The CD layer can be placed at different locations within themore » CH shell to probe the depth and extent of mix. CD layers placed flush with the gas-shell interface and recessed up to 8 ÎŒm have shown that most of the mix occurs at the inner-shell surface. In addition, time-gated x-ray images of the hotspot show large brightly-radiating objects traversing through the hotspot around bang-time, which are likely chunks of CH/CD plastic. This platform is a powerful new capability at the NIF for understanding mix, one of the key performance issues for ignition experiments.« less

  18. Apparatus for silicon web growth of higher output and improved growth stability

    DOE Patents [OSTI]

    Duncan, Charles S.; Piotrowski, Paul A.

    1989-01-01

    This disclosure describes an apparatus to improve the web growth attainable from prior web growth configurations. This apparatus modifies the heat loss at the growth interface in a manner that minimizes thickness variations across the web, especially regions of the web adjacent to the two bounding dendrites. In the unmodified configuration, thinned regions of web, adjacent to the dendrites, were found to be the origin of crystal degradation which ultimately led to termination of the web growth. According to the present invention, thinning adjacent to the dendrites is reduced and the incidence of crystal degradation is similarly reduced.

  19. Bridging the PSI Knowledge Gap: A Multi-Scale Approach

    SciTech Connect (OSTI)

    Wirth, Brian D

    2015-01-08

    Plasma-surface interactions (PSI) pose an immense scientific hurdle in magnetic confinement fusion and our present understanding of PSI in confinement environments is highly inadequate; indeed, a recent Fusion Energy Sciences Advisory Committee report found that 4 out of the 5 top five fusion knowledge gaps were related to PSI. The time is appropriate to develop a concentrated and synergistic science effort that would expand, exploit and integrate the wealth of laboratory ion-beam and plasma research, as well as exciting new computational tools, towards the goal of bridging the PSI knowledge gap. This effort would broadly advance plasma and material sciences, while providing critical knowledge towards progress in fusion PSI. This project involves the development of a Science Center focused on a new approach to PSI science; an approach that both exploits access to state-of-the-art PSI experiments and modeling, as well as confinement devices. The organizing principle is to develop synergistic experimental and modeling tools that treat the truly coupled multi-scale aspect of the PSI issues in confinement devices. This is motivated by the simple observation that while typical lab experiments and models allow independent manipulation of controlling variables, the confinement PSI environment is essentially self-determined with few outside controls. This means that processes that may be treated independently in laboratory experiments, because they involve vastly different physical and time scales, will now affect one another in the confinement environment. Also, lab experiments cannot simultaneously match all exposure conditions found in confinement devices typically forcing a linear extrapolation of lab results. At the same time programmatic limitations prevent confinement experiments alone from answering many key PSI questions. The resolution to this problem is to usefully exploit access to PSI science in lab devices, while retooling our thinking from a linear and de-coupled extrapolation to a multi-scale, coupled approach. The PSI Plasma Center consisted of three equal co-centers; one located at the MIT Plasma Science and Fusion Center, one at UC San Diego Center for Energy Research and one at the UC Berkeley Department of Nuclear Engineering, which moved to the University of Tennessee, Knoxville (UTK) with Professor Brian Wirth in July 2010. The Center had three co-directors: Prof. Dennis Whyte led the MIT co-center, the UCSD co-center was led by Dr. Russell Doerner, and Prof. Brian Wirth led the UCB/UTK center. The directors have extensive experience in PSI and material research, and have been internationally recognized in the magnetic fusion, materials and plasma research fields. The co-centers feature keystone PSI experimental and modeling facilities dedicated to PSI science: the DIONISOS/CLASS facility at MIT, the PISCES facility at UCSD, and the state-of-the-art numerical modeling capabilities at UCB/UTK. A collaborative partner in the center is Sandia National Laboratory at Livermore (SNL/CA), which has extensive capabilities with low energy ion beams and surface diagnostics, as well as supporting plasma facilities, including the Tritium Plasma Experiment, all of which significantly augment the Center. Interpretive, continuum material models are available through SNL/CA, UCSD and MIT. The participating institutions of MIT, UCSD, UCB/UTK, SNL/CA and LLNL brought a formidable array of experimental tools and personnel abilities into the PSI Plasma Center. Our work has focused on modeling activities associated with plasma surface interactions that are involved in effects of He and H plasma bombardment on tungsten surfaces. This involved performing computational material modeling of the surface evolution during plasma bombardment using molecular dynamics modeling. The principal outcomes of the research efforts within the combined experimental – modeling PSI center are to provide a knowledgebase of the mechanisms of surface degradation, and the influence of the surface on plasma conditions.

  20. Growth Mode and Substrate Symmetry Dependent Strain in Epitaxial...

    Office of Scientific and Technical Information (OSTI)

    Growth Mode and Substrate Symmetry Dependent Strain in Epitaxial Graphene. Citation Details In-Document Search Title: Growth Mode and Substrate Symmetry Dependent Strain in...

  1. OECD-Fostering Innovation for Green Growth | Open Energy Information

    Open Energy Info (EERE)

    Fostering Innovation for Green Growth Jump to: navigation, search Tool Summary LAUNCH TOOL Name: OECD-Fostering Innovation for Green Growth AgencyCompany Organization:...

  2. Indonesia-Low Carbon Growth Project | Open Energy Information

    Open Energy Info (EERE)

    Growth Project Jump to: navigation, search Name Indonesia Low Carbon Growth Project AgencyCompany Organization United Kingdom Department for International Development Partner...

  3. Kenya-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Kenya-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  4. India-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name India-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  5. Brazil-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Brazil-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  6. Poland-Low Carbon Growth Country Studies Program | Open Energy...

    Open Energy Info (EERE)

    Low Carbon Growth Country Studies Program Jump to: navigation, search Name Poland-Low Carbon Growth Country Studies Program AgencyCompany Organization Energy Sector Management...

  7. Guyana-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Guyana-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  8. Mexico-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Mexico-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  9. Malaysia-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    Malaysia-ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Malaysia-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks,...

  10. Indonesia-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Indonesia-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  11. Egypt-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Egypt-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  12. Ethiopia-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    Ethiopia-ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Ethiopia-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks,...

  13. Republic of Macedonia-Low Carbon Growth Country Studies Program...

    Open Energy Info (EERE)

    Low Carbon Growth Country Studies Program Jump to: navigation, search Name Republic of Macedonia-Low Carbon Growth Country Studies Program AgencyCompany Organization Energy...

  14. Before the Subcommittee on Economic Growth, Job Creation and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Economic Growth, Job Creation and Regulatory Affairs - House Committee on Oversight and Governmant Reform Before the Subcommittee on Economic Growth, Job Creation and Regulatory ...

  15. Thailand-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    search Name Thailand-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI) Partner Korea International Cooperation Agency (KOICA)...

  16. Cambodia-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    search Name Cambodia-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI) Partner Korea International Cooperation Agency (KOICA)...

  17. Global Green Growth Institute (GGGI) | Open Energy Information

    Open Energy Info (EERE)

    "GGGI is dedicated to pioneering and diffusing a new model of economic growth, known as "green growth," that simultaneously targets key aspects of economic performance, such as...

  18. Green Growth e-Learning | Open Energy Information

    Open Energy Info (EERE)

    Tool Summary LAUNCH TOOL Name: Green Growth e-Learning AgencyCompany Organization: Green Growth Best Practice Initiative (GGBPI) Focus Area: Economic Development, Energy...

  19. Peru-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    navigation, search Name Peru-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI) Partner Korea International Cooperation Agency (KOICA)...

  20. Jordan-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    navigation, search Name Jordan-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI) Partner Korea International Cooperation Agency (KOICA)...

  1. Ethiopia-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    search Name Ethiopia-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI), Korea International Cooperation Agency (KOICA) Partner...

  2. Understanding Cost Growth and Performance Shortfalls in Pioneer...

    Office of Environmental Management (EM)

    Cost Growth and Performance Shortfalls in Pioneer Process Plants Understanding Cost Growth and Performance Shortfalls in Pioneer Process Plants This report presents an empirical...

  3. Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure Development Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure Development Presented at ...

  4. Synthesis of segmented silica rods by growth temperature regulation...

    Office of Scientific and Technical Information (OSTI)

    silica rods by growth temperature regulation Citation Details In-Document Search Title: Synthesis of segmented silica rods by growth temperature regulation Authors: Sharma, ...

  5. ClimateWorks-Egypt-Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks-Egypt-Low Carbon Growth Planning Support Redirect page Jump to: navigation, search REDIRECT ClimateWorks Low Carbon Growth Planning Support Retrieved from "http:...

  6. Low Carbon Growth: a Potential Path for Mexico - GHG Abatement...

    Open Energy Info (EERE)

    "ESMAP Low Carbon Growth Country Studies Program" Retrieved from "http:en.openei.orgwindex.php?titleLowCarbonGrowth:aPotentialPathforMexico-GHGAbatementCostCurve&...

  7. Low Carbon Green Growth: Integrated Policy Approach to Climate...

    Open Energy Info (EERE)

    Growth: Integrated Policy Approach to Climate Change for Asia-Pacific Developing Countries Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Low Carbon Green Growth:...

  8. Ghana Goes for Green Growth: National Engagement on Climate Change...

    Open Energy Info (EERE)

    Ghana Goes for Green Growth: National Engagement on Climate Change Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Ghana Goes for Green Growth: National Engagement on...

  9. Enhancing Plant Growth and Stress Tolerance through Use of Fungi...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Enhancing Plant Growth and Stress Tolerance through Use of Fungi and Bacteria that Comprise Plant Microbiomes Enhancing Plant Growth and Stress Tolerance through Use of Fungi and...

  10. From Climate Finance to Financing Green Growth | Open Energy...

    Open Energy Info (EERE)

    green growth and the importance of developing the right policies to support a transition towards the low carbon economy. It assesses the financing needs of green growth in...

  11. China-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name China-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  12. Operation of Lanzhou all permanent electron cyclotron resonance ion source No. 2 on 320 kV platform with highly charged ions

    SciTech Connect (OSTI)

    Lu, W.; Li, J. Y.; Kang, L.; Liu, H. P.; Li, H.; Li, J. D.; Sun, L. T.; Ma, X. W.

    2014-02-15

    The 320 kV platform for multi-discipline research with highly charged ions is a heavy ion beam acceleration instrument developed by Institute of Modern Physics, which is dedicated to basic scientific researches such as plasma, atom, material physics, and astrophysics, etc. The platform has delivered ion beams of 400 species for 36?000 h. The average operation time is around 5000 h/year. With the beams provided by the platform, lots of outstanding progresses were made in various research fields. The ion source of the platform is an all-permanent magnet electron cyclotron resonance ion source, LAPECR2 (Lanzhou All Permanent ECR ion source No. 2). The maximum axial magnetic fields are 1.28 T at injection and 1.07 T at extraction, and the radial magnetic field is up to 1.21 T at the inner wall of the plasma chamber. The ion source is capable to produce low, medium, and high charge state gaseous and metallic ion beams, such as H{sup +}, {sup 40}Ar{sup 8+}, {sup 129}Xe{sup 30+}, {sup 209}Bi{sup 33+}, etc. This paper will present the latest result of LAPECR2 and the routine operation status for the high voltage platform.

  13. Systems and methods for knowledge discovery in spatial data

    DOE Patents [OSTI]

    Obradovic, Zoran; Fiez, Timothy E.; Vucetic, Slobodan; Lazarevic, Aleksandar; Pokrajac, Dragoljub; Hoskinson, Reed L.

    2005-03-08

    Systems and methods are provided for knowledge discovery in spatial data as well as to systems and methods for optimizing recipes used in spatial environments such as may be found in precision agriculture. A spatial data analysis and modeling module is provided which allows users to interactively and flexibly analyze and mine spatial data. The spatial data analysis and modeling module applies spatial data mining algorithms through a number of steps. The data loading and generation module obtains or generates spatial data and allows for basic partitioning. The inspection module provides basic statistical analysis. The preprocessing module smoothes and cleans the data and allows for basic manipulation of the data. The partitioning module provides for more advanced data partitioning. The prediction module applies regression and classification algorithms on the spatial data. The integration module enhances prediction methods by combining and integrating models. The recommendation module provides the user with site-specific recommendations as to how to optimize a recipe for a spatial environment such as a fertilizer recipe for an agricultural field.

  14. Knowledge Discovery and Data Mining (KDDM) survey report.

    SciTech Connect (OSTI)

    Phillips, Laurence R.; Jordan, Danyelle N.; Bauer, Travis L.; Elmore, Mark T.; Treadwell, Jim N.; Homan, Rossitza A.; Chapman, Leon Darrel; Spires, Shannon V.

    2005-02-01

    The large number of government and industry activities supporting the Unit of Action (UA), with attendant documents, reports and briefings, can overwhelm decision-makers with an overabundance of information that hampers the ability to make quick decisions often resulting in a form of gridlock. In particular, the large and rapidly increasing amounts of data and data formats stored on UA Advanced Collaborative Environment (ACE) servers has led to the realization that it has become impractical and even impossible to perform manual analysis leading to timely decisions. UA Program Management (PM UA) has recognized the need to implement a Decision Support System (DSS) on UA ACE. The objective of this document is to research the commercial Knowledge Discovery and Data Mining (KDDM) market and publish the results in a survey. Furthermore, a ranking mechanism based on UA ACE-specific criteria has been developed and applied to a representative set of commercially available KDDM solutions. In addition, an overview of four R&D areas identified as critical to the implementation of DSS on ACE is provided. Finally, a comprehensive database containing detailed information on surveyed KDDM tools has been developed and is available upon customer request.

  15. Report on a Zero-Knowledge Protocal Tabletop Exercise.

    SciTech Connect (OSTI)

    Marleau, Peter; Brubaker, Erik; Deland, Sharon M.; Hilton, Nathan R.; McDaniel, Michael; Schroeppel, Richard C.; Seager, Kevin D.; Stoddard, Mary Clare; MacArthur, Duncan

    2015-06-01

    This report summarizes the discussion and conclusions reached during a table top exercise held at Sandia National Laboratories, Albuquerque on September 3, 2014 regarding a recently described approach for nuclear warhead verification based on the cryptographic concept of a zero-knowledge protocol (ZKP) presented in a recent paper authored by Glaser, Barak, and Goldston. A panel of Sandia National Laboratories researchers, whose expertise includes radiation instrumentation design and development, cryptography, and arms control verification implementation, jointly reviewed the paper and identified specific challenges to implementing the approach as well as some opportunities. It was noted that ZKP as used in cryptography is a useful model for the arms control verification problem, but the direct analogy to arms control breaks down quickly. The ZKP methodology for warhead verification fits within the general class of template-based verification techniques, where a reference measurement is used to confirm that a given object is like another object that has already been accepted as a warhead by some other means. This can be a powerful verification approach, but requires independent means to trust the authenticity of the reference warhead - a standard that may be difficult to achieve, which the ZKP authors do not directly address. Despite some technical challenges, the concept of last-minute selection of the pre-loads and equipment could be a valuable component of a verification regime.

  16. Sustaining knowledge in the neutron generator community and benchmarking study. Phase II.

    SciTech Connect (OSTI)

    Huff, Tameka B.; Stubblefield, William Anthony; Cole, Benjamin Holland, II; Baldonado, Esther

    2010-08-01

    This report documents the second phase of work under the Sustainable Knowledge Management (SKM) project for the Neutron Generator organization at Sandia National Laboratories. Previous work under this project is documented in SAND2008-1777, Sustaining Knowledge in the Neutron Generator Community and Benchmarking Study. Knowledge management (KM) systems are necessary to preserve critical knowledge within organizations. A successful KM program should focus on people and the process for sharing, capturing, and applying knowledge. The Neutron Generator organization is developing KM systems to ensure knowledge is not lost. A benchmarking study involving site visits to outside industry plus additional resource research was conducted during this phase of the SKM project. The findings presented in this report are recommendations for making an SKM program successful. The recommendations are activities that promote sharing, capturing, and applying knowledge. The benchmarking effort, including the site visits to Toyota and Halliburton, provided valuable information on how the SEA KM team could incorporate a KM solution for not just the neutron generators (NG) community but the entire laboratory. The laboratory needs a KM program that allows members of the workforce to access, share, analyze, manage, and apply knowledge. KM activities, such as communities of practice (COP) and sharing best practices, provide a solution towards creating an enabling environment for KM. As more and more people leave organizations through retirement and job transfer, the need to preserve knowledge is essential. Creating an environment for the effective use of knowledge is vital to achieving the laboratory's mission.

  17. Growth Kinetics and Modeling of Direct Oxynitride Growth with NO-O2 Gas Mixtures

    SciTech Connect (OSTI)

    Everist, Sarah; Nelson, Jerry; Sharangpani, Rahul; Smith, Paul Martin; Tay, Sing-Pin; Thakur, Randhir

    1999-05-03

    We have modeled growth kinetics of oxynitrides grown in NO-O2 gas mixtures from first principles using modified Deal-Grove equations. Retardation of oxygen diffusion through the nitrided dielectric was assumed to be the dominant growth-limiting step. The model was validated against experimentally obtained curves with good agreement. Excellent uniformity, which exceeded expected walues, was observed.

  18. Role of nucleation in nanodiamond film growth

    SciTech Connect (OSTI)

    Lifshitz, Y.; Lee, C.H.; Wu, Y.; Zhang, W.J.; Bello, I.; Lee, S.T.

    2006-06-12

    Nanodiamond films were deposited using different microwave plasma chemical vapor deposition schemes following several nucleation pretreatment methods. The nucleation efficiency and the films structure were investigated using scanning and transmission electron microscopy and Raman spectroscopy. C{sub 2} dimer growth (CH{sub 4} and H{sub 2} in 90% Ar) cannot nucleate diamond and works only on existing diamond surfaces. The methyl radical process (up to 20% CH{sub 4} in H{sub 2}) allows some nucleation probability on appropriate substrates. Prolonged bias enhanced nucleation initiates both diamond nucleation and growth. C{sub 2} dimer growth results in pure nanodiamond free of amorphous carbon, while prolonged bias enhanced nucleation forms an amorphous carbon/nanodiamond composite.

  19. Efg Crystal Growth Apparatus And Method

    DOE Patents [OSTI]

    Mackintosh, Brian H. (Concord, MA); Ouellette, Marc (Nashua, NH)

    2003-05-13

    An improved mechanical arrangement controls the introduction of silicon particles into an EFG (Edge-defined Film-fed Growth) crucible/die unit for melt replenishment during a crystal growth run. A feeder unit injects silicon particles upwardly through a center hub of the crucible/die unit and the mechanical arrangement intercepts the injected particles and directs them so that they drop into the melt in a selected region of the crucible and at velocity which reduces splashing, whereby to reduce the likelihood of interruption of the growth process due to formation of a solid mass of silicon on the center hub and adjoining components. The invention also comprises use of a Faraday ring to alter the ratio of the electrical currents flowing through primary and secondary induction heating coils that heat the crucible die unit and the mechanical arrangement.

  20. Crystal growth and annealing method and apparatus

    DOE Patents [OSTI]

    Gianoulakis, Steven E.; Sparrow, Robert

    2001-01-01

    A method and apparatus for producing crystals that minimizes birefringence even at large crystal sizes, and is suitable for production of CaF.sub.2 crystals. The method of the present invention comprises annealing a crystal by maintaining a minimal temperature gradient in the crystal while slowly reducing the bulk temperature of the crystal. An apparatus according to the present invention includes a thermal control system added to a crystal growth and annealing apparatus, wherein the thermal control system allows a temperature gradient during crystal growth but minimizes the temperature gradient during crystal annealing. An embodiment of the present invention comprises a secondary heater incorporated into a conventional crystal growth and annealing apparatus. The secondary heater supplies heat to minimize the temperature gradients in the crystal during the annealing process. The secondary heater can mount near the bottom of the crucible to effectively maintain appropriate temperature gradients.

  1. Investigating the Nexus of Climate, Energy, Water, and Land at Decision-Relevant Scales: The Platform for Regional Integrated Modeling and Analysis (PRIMA)

    SciTech Connect (OSTI)

    Kraucunas, Ian P.; Clarke, Leon E.; Dirks, James A.; Hathaway, John E.; Hejazi, Mohamad I.; Hibbard, Kathleen A.; Huang, Maoyi; Jin, Chunlian; Kintner-Meyer, Michael C.W.; Kleese van Dam, Kerstin; Leung, Lai-Yung R.; Li, Hongyi; Moss, Richard H.; Peterson, Marty J.; Rice, Jennie S.; Scott, Michael J.; Thomson, Allison M.; Voisin, Nathalie; West, Tristram O.

    2015-04-01

    The Platform for Regional Integrated Modeling and Analysis (PRIMA) is an innovative modeling system developed at Pacific Northwest National Laboratory (PNNL) to simulate interactions among natural and human systems at scales relevant to regional decision making. PRIMA brings together state-of-the-art models of regional climate, hydrology, agriculture, socioeconomics, and energy systems using a flexible coupling approach. The platform can be customized to inform a variety of complex questions and decisions, such as the integrated evaluation of mitigation and adaptation options across a range of sectors. Research into stakeholder decision support needs underpins the platform's application to regional issues, including uncertainty characterization. Ongoing numerical experiments are yielding new insights into the interactions among human and natural systems on regional scales with an initial focus on the energy-land-water nexus in the upper U.S. Midwest. This paper focuses on PRIMA’s functional capabilities and describes some lessons learned to date about integrated regional modeling.

  2. Klebsiella pneumoniae inoculants for enhancing plant growth

    DOE Patents [OSTI]

    Triplett, Eric W. (Middleton, WI); Kaeppler, Shawn M. (Oregon, WI); Chelius, Marisa K. (Greeley, CO)

    2008-07-01

    A biological inoculant for enhancing the growth of plants is disclosed. The inoculant includes the bacterial strains Herbaspirillum seropedicae 2A, Pantoea agglomerans P101, Pantoea agglomerans P102, Klebsiella pneumoniae 342, Klebsiella pneumoniae zmvsy, Herbaspirillum seropedicae Z152, Gluconacetobacter diazotrophicus PA15, with or without a carrier. The inoculant also includes strains of the bacterium Pantoea agglomerans and K. pneumoniae which are able to enhance the growth of cereal grasses. Also disclosed are the novel bacterial strains Herbaspirillum seropedicae 2A, Pantoea agglomerans P101 and P102, and Klebsiella pneumoniae 342 and zmvsy.

  3. Direct growth of graphene on Si(111)

    SciTech Connect (OSTI)

    Thanh Trung, Pham Joucken, Frédéric; Colomer, Jean-François; Robert, Sporken; Campos-Delgado, Jessica; Raskin, Jean-Pierre; Hackens, Benoît; Santos, Cristiane N.

    2014-06-14

    Due to the need of integrated circuit in the current silicon technology, the formation of graphene on Si wafer is highly desirable, but is still a challenge for the scientific community. In this context, we report the direct growth of graphene on Si(111) wafer under appropriate conditions using an electron beam evaporator. The structural quality of the material is investigated in detail by reflection high energy electron diffraction, Auger electron spectroscopy, X-ray photoemission spectroscopy, Raman spectroscopy, high resolution scanning electron microscopy, atomic force microscopy, and scanning tunneling microscopy. Our experimental results confirm that the quality of graphene is strongly dependent on the growth time during carbon atoms deposition.

  4. A High Performance Computing Platform for Performing High-Volume Studies With Windows-based Power Grid Tools

    SciTech Connect (OSTI)

    Chen, Yousu; Huang, Zhenyu

    2014-08-31

    Serial Windows-based programs are widely used in power utilities. For applications that require high volume simulations, the single CPU runtime can be on the order of days or weeks. The lengthy runtime, along with the availability of low cost hardware, is leading utilities to seriously consider High Performance Computing (HPC) techniques. However, the vast majority of the HPC computers are still Linux-based and many HPC applications have been custom developed external to the core simulation engine without consideration for ease of use. This has created a technical gap for applying HPC-based tools to today’s power grid studies. To fill this gap and accelerate the acceptance and adoption of HPC for power grid applications, this paper presents a prototype of generic HPC platform for running Windows-based power grid programs on Linux-based HPC environment. The preliminary results show that the runtime can be reduced from weeks to hours to improve work efficiency.

  5. DEVELOPMENT OF AN INSPECTION PLATFORM AND A SUITE OF SENSORS FOR ASSESSING CORROSION AND MECHANICAL DAMAGE ON UNPIGGABLE TRANSMISSION MAINS

    SciTech Connect (OSTI)

    George C. Vradis

    2003-05-01

    The present report summarizes the accomplishments of the project during its second three-month period (from January 2003 through March 2003). The project was initiated with delay in February 2003 due to contractual issues that emerged between the NGA and Foster-Miller, Inc. The two organizations are working diligently to maintain the program's pace so that it is completed in time. The efforts of the project focused during this period in the assessment of the tether technology that is intended to be used as the means of communication between robot and operator. Preliminary results indicate that tether is a viable option under certain pipeline operating conditions but not all. The exact range of operating conditions that are viable for tether use are being determined as the study progresses. Work was also initiated regarding the design of the robotic platform.

  6. Performance Tuning of Fock Matrix and Two-Electron Integral Calculations for NWChem on Leading HPC Platforms

    SciTech Connect (OSTI)

    Shan, Hongzhan; Austin, Brian M.; De Jong, Wibe A.; Oliker, Leonid; Wright, Nicholas J.; Apra, Edoardo

    2014-10-01

    Attaining performance in the evaluation of two-electron repulsion integrals and constructing the Fock matrix is of considerable importance to the computational chemistry community. Due to its numerical complexity improving the performance behavior across a variety of leading supercomputing platforms is an increasing challenge due to the significant diversity in high-performance computing architectures. In this paper, we present our successful tuning methodology for these important numerical methods on the Cray XE6, the Cray XC30, the IBM BG/Q, as well as the Intel Xeon Phi. Our optimization schemes leverage key architectural features including vectorization and simultaneous multithreading, and results in speedups of up to 2.5x compared with the original implementation.

  7. DEVELOPMENT OF AN INSPECTION PLATFORM AND A SUITE OF SENSORS FOR ASSESSING CORROSION AND MECHANICAL DAMAGE ON UNPIGGABLE TRANSMISSION MAINS

    SciTech Connect (OSTI)

    George C. Vradis; William Leary

    2004-03-01

    The National Energy Technology Laboratory of the US Department of Energy (under Award DE-FC26-02NT41645) and the NYSEARCH Committee of the Northeast Gas Association (previous the New York Gas Group), have sponsored research to develop a robotic pipeline inspection system capable of navigation through the typical physical and operational obstacles that make transmission and distribution pipelines unpiggable. The research contractors, Foster-Miller and GE Oil & Gas (PII North America) have performed an engineering study and developed a conceptual design that meets all the requirements for navigating and inspecting unpiggable transmission pipelines. Based on Foster-Miller's previous efforts developing the Pipe Mouse robot, the RoboScan inspection robot (Figure ES-1) meets the navigational and physical challenges of unpiggable pipelines through an innovative modular platform design, segmented MFL inspection modules and improvements to the inter-module coupling design.

  8. Nonlinear automatic landing control of unmanned aerial vehicles on moving platforms via a 3D laser radar

    SciTech Connect (OSTI)

    Hervas, Jaime Rubio; Tang, Hui; Reyhanoglu, Mahmut

    2014-12-10

    This paper presents a motion tracking and control system for automatically landing Unmanned Aerial Vehicles (UAVs) on an oscillating platform using Laser Radar (LADAR) observations. The system itself is assumed to be mounted on a ship deck. A full nonlinear mathematical model is first introduced for the UAV. The ship motion is characterized by a Fourier transform based method which includes a realistic characterization of the sea waves. LADAR observation models are introduced and an algorithm to process those observations for yielding the relative state between the vessel and the UAV is presented, from which the UAV's state relative to an inertial frame can be obtained and used for feedback purposes. A sliding mode control algorithm is derived for tracking a landing trajectory defined by a set of desired waypoints. An extended Kalman filter (EKF) is proposed to account for process and observation noises in the design of a state estimator. The effectiveness of the control algorithm is illustrated through a simulation example.

  9. Microfluidic Technology Platforms for Synthesizing, Labeling and Measuring the Kinetics of Transport and Biochemical Reactions for Developing Molecular Imaging Probes

    SciTech Connect (OSTI)

    Phelps, Michael E.

    2009-09-01

    Radiotracer techniques are used in environmental sciences, geology, biology and medicine. Radiotracers with Positron Emission Tomography (PET) provided biological examinations of ~3 million patients 2008. Despite the success of positron labeled tracers in many sciences, there is limited access in an affordable and convenient manner to develop and use new tracers. Integrated microfluidic chips are a new technology well matched to the concentrations of tracers. Our goal is to develop microfluidic chips and new synthesis approaches to enable wide dissemination of diverse types of tracers at low cost, and to produce new generations of radiochemists for which there are many unfilled jobs. The program objectives are to: 1. Develop an integrated microfluidic platform technology for synthesizing and 18F-labeling diverse arrays of different classes of molecules. 2. Incorporate microfluidic chips into small PC controlled devices (“Synthesizer”) with a platform interfaced to PC for electronic and fluid input/out control. 3. Establish a de-centralized model with Synthesizers for discovering and producing molecular imaging probes, only requiring delivery of inexpensive [18F]fluoride ion from commercial PET radiopharmacies vs the centralized approach of cyclotron facilities synthesizing and shipping a few different types of 18F-probes. 4. Develop a position sensitive avalanche photo diode (PSAPD) camera for beta particles embedded in a microfluidic chip for imaging and measuring transport and biochemical reaction rates to valid new 18F-labeled probes in an array of cell cultures. These objectives are met within a research and educational program integrating radio-chemistry, synthetic chemistry, biochemistry, engineering and biology in the Crump Institute for Molecular Imaging. The Radiochemistry Training Program exposes PhD and post doctoral students to molecular imaging in vitro in cells and microorganisms in microfluidic chips and in vivo with PET, from new technologies for radiochemistry (macro to micro levels), biochemistry and biology to imaging principles, tracer kinetics, pharmacokinetics and biochemical assays. New generations of radiochemists will be immersed in the biochemistry and biology for which their labeled probes are being developed for assays of these processes. In this program engineers and radio-chemists integrate the principles of microfluidics and radiolabeling along with proper system design and chemistry rule sets to yield Synthesizers enabling biological and pharmaceutical scientists to develop diverse arrays of probes to pursue their interests. This progression would allow also radiochemists to focus on the further evolution of rapid, high yield synthetic reactions with new enabling technologies, rather than everyday production of radiotracers that should be done by technologists. The invention of integrated circuits in electronics established a platform technology that allowed an evolution of ideas and applications far beyond what could have been imagined at the beginning. Rather than provide a technology for the solution to a single problem, it is hoped that microfluidic radiochemistry will be an enabling platform technology for others to solve many problems. As part of this objective, another program goal is to commercialize the technologies that come from this work so that they can be provided to others who wish to use it.

  10. PROJECT PROFILE: CyDER: A Cyber Physical Co-simulation Platform for Distributed Energy Resources in Smart Grids (SuNLaMP)

    Broader source: Energy.gov [DOE]

    This project focuses on developing a modular, scalable, and interoperable tool for power system planning and operation that will seamlessly integrate with utilities’ existing tools to enable analysis of high penetration of distributed energy resources. The tool, Cyber Physical Co-simulation Platform for Distributed Energy Resources in Smart Grids (CyDER), will enhance current utility tools by providing a computationally efficient platform that will be capable of quasi-static time series simulation and smart PV inverter controls with in-feed data from real-time distribution sensor measurements.

  11. Digital field-bus mode SCADA is key to offshore efficiency. [Automation of offshore gas production platforms

    SciTech Connect (OSTI)

    Cuthbert, P. )

    1994-02-01

    An all-digital SCADA network has been installed in one of the North Sea's largest natural gas fields, controlling the delivery of gas from Shell UK Exploration and Production's souther-area fields to a British Gas Terminal at Bacton, UK. The innovative use of digital technology -- based on the industry-standard HART field protocol -- to complete a digital communications link stretching from the onshore SCADA host right out to the process variable transmitters on the platforms, is playing a key role in the automation of the monitoring and control system by allowing Shell UK Expro to run the majority of the platforms unmanned. The SCADA system is part of a major refit being carried out by Shell Expro on its Leman field. The refit is part of the company's long-term strategy to extend the lifetime of this established field, which started operations in the late 1960s. In order to meet this goal, the prime requirements are to reduce operational costs and risk exposure, and the key element in this area was to reduce the need for resident staff and all of their associated support and equipment costs, through the deployment of automation. The system will achieve the project's cost-cutting aims, but also break new ground in control and monitoring technology for the gas industry, through the use of a smart transmitter scheme as a digital field communications within the wide-area network, using the protocol's all-digital capability in preference to the commonly used 4-20mA-compatible mode, will allow real-time monitoring and control, plus maintenance and diagnostics, to take place remotely. This paper describes the design of this system.

  12. Test Your Energy Knowledge with Our Bioenergy Quiz | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Test Your Energy Knowledge with Our Bioenergy Quiz Test Your Energy Knowledge with Our Bioenergy Quiz May 22, 2015 - 10:33am Addthis Test Your Energy Knowledge with Our Bioenergy Quiz Jonathan Male Jonathan Male Director, Bioenergy Technologies Office I am very excited to announce our first ever bioenergy quiz-an online, interactive tool that's both enlightening and entertaining! Interested in participating? Just click the link in the photo above and let the game begin. Think you know the facts

  13. Soybean Knowledge Base (SoyKB): a Web Resource for Soybean Translational

    Office of Scientific and Technical Information (OSTI)

    Genomics (Journal Article) | SciTech Connect Soybean Knowledge Base (SoyKB): a Web Resource for Soybean Translational Genomics Citation Details In-Document Search Title: Soybean Knowledge Base (SoyKB): a Web Resource for Soybean Translational Genomics Background: Soybean Knowledge Base (SoyKB) is a comprehensive all-inclusive web resource for soybean translational genomics. SoyKB is designed to handle the management and integration of soybean genomics, transcriptomics, proteomics and

  14. System and method for knowledge based matching of users in a network

    DOE Patents [OSTI]

    Verspoor, Cornelia Maria; Sims, Benjamin Hayden; Ambrosiano, John Joseph; Cleland, Timothy James

    2011-04-26

    A knowledge-based system and methods to matchmaking and social network extension are disclosed. The system is configured to allow users to specify knowledge profiles, which are collections of concepts that indicate a certain topic or area of interest selected from an. The system utilizes the knowledge model as the semantic space within which to compare similarities in user interests. The knowledge model is hierarchical so that indications of interest in specific concepts automatically imply interest in more general concept. Similarity measures between profiles may then be calculated based on suitable distance formulas within this space.

  15. New America Foundation: Eric Isaacs - Can our knowledge enterprise seed the

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    industries of tomorrow? | Argonne National Laboratory New America Foundation: Eric Isaacs - Can our knowledge enterprise seed the industries of tomorrow? Share Topic Operations Technology transfer

  16. Melt dumping in string stabilized ribbon growth

    DOE Patents [OSTI]

    Sachs, Emanuel M. (42 Old Middlesex Rd., Belmont, MA 02178)

    1986-12-09

    A method and apparatus for stabilizing the edge positions of a ribbon drawn from a melt includes the use of wettable strings drawn in parallel up through the melt surface, the ribbon being grown between the strings. A furnace and various features of the crucible used therein permit continuous automatic growth of flat ribbons without close temperature control or the need for visual inspection.

  17. Growth Of Oriented Crystals At Polymerized Membranes

    DOE Patents [OSTI]

    Charych, Deborah H. (Albany, CA), Berman, Amir (Ben-Shiva, IL)

    2000-01-25

    The present invention relates to methods and compositions for the growth and alignment of crystals at biopolymeric films. The methods and compositions of the present invention provide means to generate a variety of dense crystalline ceramic films, with totally aligned crystals, at low temperatures and pressures, suitable for use with polymer and plastic substrates.

  18. Use of acceptable knowledge to demonstrate TRAMPAC compliance

    SciTech Connect (OSTI)

    Whitworth, J. (Julia); Becker, B. (Blair); Guerin, D. (David); Shokes, T. (Tamara)

    2004-01-01

    Recently, Los Alamos National Laboratory-Carlsbad Operations (LANL-CO) has supported the Central Characterization Project (CCP) managed by the U.S. Department of Energy (DOE) in the shipment of transuranic (TRU) waste from various small-quantity TRU waste generators to hub sites or other DOE sites in TRUPACT-II shipping containers. This support has involved using acceptable knowledge (AK) to demonstrate compliance with various requirements of Revision 19 of the TRUPACT-II Authorized Methods of Payload Compliance (TRAMPAC). LANL-CO has worked to facilitate TRUPACT-II shipments from the University of Missouri Research Reactor (MURR) and Lovelace Respiratory Research Institute (LRRI) to Argonne National Laboratory-East (ANL-E) and Los Alamos National Laboratory (LANL), respectively. The latter two sites have TRU waste certification programs approved to ship waste to the Waste Isolation Pilot Plant (WIPP) for disposal. In each case, AK was used to satisfy the necessary information to ship the waste to other DOE facilities. For the purposes of intersite shipment, AK provided data to WIPP Waste Information System (WWIS) transportation modules to ensure that required information was obtained prior to TRUPACT-II shipments. The WWIS modules were used for the intersite shipments, not to enter certification data into WWIS, but rather to take advantage of a validated system to ensure that the containers to be shipped were compliant with TRAMPAC requirements, particularly in the evaluation of quantitative criteria. LANL-CO also assisted with a TRAMPAC compliance demonstration for homogeneous waste containers shipped in TRUPACT-II containers from ANL-E to Idaho National Engineering and Environmental Laboratory (INEEL) for the purpose of core sampling. The basis for the TRAMPAC compliance determinations was AK regarding radiological composition, chemical composition, TRU waste container packaging, and absence of prohibited items. Also, even in the case where AK is not used to fully demonstrate TRAMPAC compliance, it may be used to identify problem areas for shippability of different waste streams. An example is the case of Pu-238-contaminated waste from the Savannah River Site that had a low probability of meeting decay heat limits and aspiration times due to several factors including large numbers of confinement layers. This paper will outline 17 TRAMPAC compliance criteria assessed and the types of information used to show compliance with all criteria other than dose rate and container weight, which are normally easily measured at load preparation.

  19. Driving Down HB-LED Costs: Implementation of Process Simulation Tools and Temperature Control Methods of High Yield MOCVD Growth

    SciTech Connect (OSTI)

    William Quinn

    2012-04-30

    The overall objective of this multi-faceted program is to develop epitaxial growth systems that meet a goal of 75% (4X) cost reduction in the epitaxy phase of HB-LED manufacture. A 75% reduction in yielded epitaxy cost is necessary in order to achieve the cost goals for widespread penetration of HB-LEDñ€™s into back-lighting units (BLU) for LCD panels and ultimately for solid-state lighting (SSL). To do this, the program will address significant improvements in overall equipment Cost of Ownership, or CoO. CoO is a model that includes all costs associated with the epitaxy portion of production. These aspects include cost of yield, capital cost, operational costs, and maintenance costs. We divide the program into three phases where later phases will incorporate the gains of prior phases. Phase one activities are enabling technologies. In collaboration with Sandia National Laboratories we develop a Fluent-compatible chemistry predictive model and a set of mid-infrared and near-ultraviolet pyrometer monitoring tools. Where previously the modeling of the reactor dynamics were studied within FLUENT alone, here, FLUENT and Chemkin are integrated into a comprehensive model of fluid dynamics and the most advanced transport equations developed for Chemkin. Specifically, the Chemkin model offered the key reaction terms for gas-phase nucleation, a key consideration in the optimization of the MOCVD process. This new predictive model is used to design new MOCVD reactors with optimized growth conditions and the newly developed pyrometers are used monitor and control the MOCVD process temperature to within 0.5°C run-to-run and within each wafer. This portion of the grant is in collaboration with partners at Sandia National Laboratories. Phase two activities are continuous improvement projects which extend the current reactor platform along the lines of improved operational efficiency, improved systems control for throughput, and carrier modifications for increased yield. Programmatically, improvements made in Phase I are applied to developments of Phase II when applicable. Phase three is the culmination of the individual tasks from both phases one and two applied to proposed production platforms. We selectively combine previously demonstrated tasks and other options to develop a high-volume production-worthy MOCVD system demonstrating >3x throughput, 1.3x capital efficiency, and 0.7x cost of ownership. In a parallel demonstration we validate the concept of an improved, larger deposition system which utilizes the predictive modeling of chemistry-based flow analysis and extensions of the improvements demonstrated on the current platforms. This validation includes the build and testing of a prototype version of the hardware and demonstration of 69% reduction in the cost of ownership. Also, in this phase we present a stand-alone project to develop a high-temperature system which improves source efficiency by 30% while concurrently increasing growth rate by 1.3x. The material quality is held to the same material quality specifications of our existing baseline processes. The merits of other line item tasks in phase three are discussed for inclusion on next-generation platforms.

  20. System using a megawatt class millimeter wave source and a high-power rectenna to beam power to a suspended platform

    DOE Patents [OSTI]

    Caplan, Malcolm; Friedman, Herbert W.

    2005-07-19

    A system for beaming power to a high altitude platform is based upon a high power millimeter gyrotron source, optical transmission components, and a high-power receiving antenna (i.e., a rectenna) capable of rectifying received millimeter energy and converting such energy into useable electrical power.

  1. Topographical and Chemical Imaging of a Phase Separated Polymer Using a Combined Atomic Force Microscopy/Infrared Spectroscopy/Mass Spectrometry Platform

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Tai, Tamin; KarĂĄcsony, Orsolya; Bocharova, Vera; Van Berkel, Gary J.; Kertesz, Vilmos

    2016-02-18

    This article describes how the use of a hybrid atomic force microscopy/infrared spectroscopy/mass spectrometry imaging platform was demonstrated for the acquisition and correlation of nanoscale sample surface topography and chemical images based on infrared spectroscopy and mass spectrometry.

  2. Filling Knowledge Gaps with Five Fuel Cycle Studies

    SciTech Connect (OSTI)

    Steven J. Piet; Jess Gehin; William Halsey; Temitope Taiwo

    2010-11-01

    During FY 2010, five studies were conducted of technology families’ applicability to various fuel cycle strategies to fill in knowledge gaps in option space and to better understand trends and patterns. Here, a “technology family” is considered to be defined by a type of reactor and by selection of which actinides provide fuel. This report summarizes the higher-level findings; the detailed analyses and results are documented in five individual reports, as follows: • Advanced once through with uranium fuel in fast reactors (SFR), • Advanced once through (uranium fuel) or single recycle (TRU fuel) in high temperature gas cooled reactors (HTGR), • Sustained recycle with Th/U-233 in light water reactors (LWRs), • Sustained recycle with Th/U-233 in molten salt reactors (MSR), and • Several fuel cycle missions with Fusion-Fission Hybrid (FFH). Each study examined how the designated technology family could serve one or more designated fuel cycle missions, filling in gaps in overall option space. Each study contains one or more illustrative cases that show how the technology family could be used to meet a fuel cycle mission, as well as broader information on the technology family such as other potential fuel cycle missions for which insufficient information was available to include with an illustrative case. None of the illustrative cases can be considered as a reference, baseline, or nominal set of parameters for judging performance; the assessments were designed to assess areas of option space and were not meant to be optimized. There is no implication that any of the cases or technology families are necessarily the best way to meet a given fuel cycle mission. The studies provide five examples of 1-year fuel cycle assessments of technology families. There is reasonable coverage in the five studies of the performance areas of waste management and uranium utilization. The coverage of economics, safety, and proliferation resistance and physical protection in the five studies was spotty. Some studies did not have existing or past work to draw on in one or more of these areas. Resource constraints limited the amount of new analyses that could be performed. Little or no assessment was done of how soon any of the technologies could be deployed and therefore how quickly they could impact domestic or international fuel cycle performance. There were six common R&D needs, such as the value of advanced fuels, cladding, coating, and structure that would survive high neutron fluence. When a technology family is considered for use in a new fuel cycle mission, fuel cycle performance characteristics are dependent on both the design choices and the fuel cycle approach. For example, the use of the sodium-cooled fast reactor to provide recycle in either breeder or burner mode has been studied for decades, but the SFR could be considered for once-through fuel cycle with the physical reactor design and fuel management parameters changed. In addition, the sustained recycle with Th/U-233 in LWR could be achieved with a heterogeneous assembly and derated power density. Therefore, it may or may not be adjustable for other fuel cycle missions although a reactor intended for one fuel cycle mission is built. Simple parameter adjustment in applying a technology family to a new fuel cycle mission should be avoided and, if observed, the results viewed with caution.

  3. Method for solid state crystal growth

    DOE Patents [OSTI]

    Nolas, George S.; Beekman, Matthew K.

    2013-04-09

    A novel method for high quality crystal growth of intermetallic clathrates is presented. The synthesis of high quality pure phase crystals has been complicated by the simultaneous formation of both clathrate type-I and clathrate type-II structures. It was found that selective, phase pure, single-crystal growth of type-I and type-II clathrates can be achieved by maintaining sufficient partial pressure of a chemical constituent during slow, controlled deprivation of the chemical constituent from the primary reactant. The chemical constituent is slowly removed from the primary reactant by the reaction of the chemical constituent vapor with a secondary reactant, spatially separated from the primary reactant, in a closed volume under uniaxial pressure and heat to form the single phase pure crystals.

  4. Epitaxial growth of silicon for layer transfer

    DOE Patents [OSTI]

    Teplin, Charles; Branz, Howard M

    2015-03-24

    Methods of preparing a thin crystalline silicon film for transfer and devices utilizing a transferred crystalline silicon film are disclosed. The methods include preparing a silicon growth substrate which has an interface defining substance associated with an exterior surface. The methods further include depositing an epitaxial layer of silicon on the silicon growth substrate at the surface and separating the epitaxial layer from the substrate substantially along the plane or other surface defined by the interface defining substance. The epitaxial layer may be utilized as a thin film of crystalline silicon in any type of semiconductor device which requires a crystalline silicon layer. In use, the epitaxial transfer layer may be associated with a secondary substrate.

  5. Substrate solder barriers for semiconductor epilayer growth

    DOE Patents [OSTI]

    Drummond, T.J.; Ginley, D.S.; Zipperian, T.E.

    1989-05-09

    During the growth of compound semiconductors by epitaxial processes, substrates are typically mounted to a support. In modular beam epitaxy, mounting is done using indium as a solder. This method has two drawbacks: the indium reacts with the substrate, and it is difficult to uniformly wet the back of a large diameter substrate. Both of these problems have been successfully overcome by sputter coating the back of the substrate with a thin layer of tungsten carbide or tungsten carbide and gold. In addition to being compatible with the growth of high quality semiconductor epilayers this coating is also inert in all standard substrate cleaning etchants used for compound semiconductors, and provides uniform distribution of energy in radiant heating.

  6. Substrate solder barriers for semiconductor epilayer growth

    DOE Patents [OSTI]

    Drummond, T.J.; Ginley, D.S.; Zipperian, T.E.

    1987-10-23

    During the growth of compound semiconductors by epitaxial processes, substrates are typically mounted to a support. In molecular beam epitaxy, mounting is done using indium as a solder. This method has two drawbacks: the indium reacts with the substrate, and it is difficult to uniformly wet the back of a large diameter substrate. Both of these problems have been successfully overcome by sputter coating the back of the substrate with a thin layer of tungsten carbide or tungsten carbide and gold. In addition to being compatible with the growth of high quality semiconductor epilayers this coating is also inert in all standard substate cleaning etchants used for compound semiconductors, and provides uniform distribution of energy in radiant heating. 1 tab.

  7. Substrate solder barriers for semiconductor epilayer growth

    DOE Patents [OSTI]

    Drummond, Timothy J.; Ginley, David S.; Zipperian, Thomas E.

    1989-01-01

    During the growth of compound semiconductors by epitaxial processes, substrates are typically mounted to a support. In modular beam epitaxy, mounting is done using indium as a solder. This method has two drawbacks: the indium reacts with the substrate, and it is difficult to uniformly wet the back of a large diameter substrate. Both of these problems have been successfully overcome by sputter coating the back of the substrate with a thin layer of tungsten carbide or tungsten carbide and gold. In addition to being compatible with the growth of high quality semiconductor epilayers this coating is also inert in all standard substrate cleaning etchants used for compound semiconductors, and provides uniform distribution of energy in radiant heating.

  8. Career Growth | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Growth | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Library Bios Congressional Testimony Fact Sheets Newsletters Press Releases Photo Gallery Jobs Apply for Our Jobs Our Jobs Working at NNSA Blog Home /

  9. MO-E-18C-05: Global Health Catalyst: A Novel Platform for Enhancing Access to Medical Physics Education and Research Excellence (AMPERE)

    SciTech Connect (OSTI)

    Ngwa, W; Moreau, M; Asana, L

    2014-06-15

    Purpose: To develop a platform for catalyzing collaborative global Cancer Care Education and Research (CaRE), with a prime focus on enhancing Access to Medical Physics Education and Research Excellence (AMPERE) Methods: An analysis of over 50 global health collaborations between partners in the U.S. and low and middle income countries (LMIC) in Africa was carried out to assess the models of collaborations in Education and Research and relative success. A survey was carried out with questions including: the nature of the collaboration, how it was initiated, impact of culture and other factors, and recommendations for catalyzing/enhancing such collaborations. An online platform called Global Health Catalyst was developed for enhancing AMPERE. Results: The analysis yielded three main models for global health collaborations with survey providing key recommendations on how to enhance such collaborations. Based on this, the platform was developed, and customized to allow Medical Physicists and other Radiation oncology (RadOnc) professionals interested in participating in Global health to readily do so e.g. teach an online course module, participate in training Medical Physicists or other RadOnc health professionals in LMIC, co-mentor students, residents or postdocs, etc. The growing list of features on the platform also include: a feature to enable people to easily find each other, form teams, operate more effectively as partners from different disciplines, institutions, nations and cultural backgrounds, share tools and technologies, obtain seed funding to develop curricula and/or embark upon new areas of investigation, and participate in humanitarian outreach: remote treatment planning assistance, and participation in virtual Chart Rounds, etc. Conclusion: The developed Global Health Catalyst platform could enable any Medical Physicist or RadoOnc professional interested in global health to readily participate in the Education/training of next generation RadOnc professionals and global health leaders, and enhance AMPERE, especially for LMIC.

  10. Growth process for gallium nitride porous nanorods

    DOE Patents [OSTI]

    Wildeson, Isaac Harshman; Sands, Timothy David

    2015-03-24

    A GaN nanorod and formation method. Formation includes providing a substrate having a GaN film, depositing SiN.sub.x on the GaN film, etching a growth opening through the SiN.sub.x and into the GaN film, growing a GaN nanorod through the growth opening, the nanorod having a nanopore running substantially through its centerline. Focused ion beam etching can be used. The growing can be done using organometallic vapor phase epitaxy. The nanopore diameter can be controlled using the growth opening diameter or the growing step duration. The GaN nanorods can be removed from the substrate. The SiN.sub.x layer can be removed after the growing step. A SiO.sub.x template can be formed on the GaN film and the GaN can be grown to cover the SiO.sub.x template before depositing SiN.sub.x on the GaN film. The SiO.sub.x template can be removed after growing the nanorods.

  11. 1979 revenue growth belies utility industry problems

    SciTech Connect (OSTI)

    Lincicome, R.

    1980-06-01

    Despite growth in revenues during 1979, electric utilities are greatly troubled by high inflation, restricted capital, and the lack of rate relief from utility commissions. The growth, although smaller than normal, will likely convince commissions to respond to rate increase requests by authorizing only the smallest possible increases. With inflationary pressures eroding utility companies' financial base, the benefits of rate increases are wiped out after a year or so, necessitating a return to the commissions for futher adjustments. This up-down cycling is reflected in the report of the performances of the top one hundred utility companies. Earning growth statistics, sales data, financial statistics, and company performances (electric sales, customers served, revenues, and after-tax net income) of top one hundred electric utilities are given in separate tables for 1979. Overall, kWh sales were up 2.9%; revenues were up 13.4%; net income was up 8.1%; and overall earnings performance was a weak increase of 9.4%. (SAC)

  12. Theoretical priors on modified growth parametrisations

    SciTech Connect (OSTI)

    Song, Yong-Seon; Hollenstein, Lukas; Caldera-Cabral, Gabriela; Koyama, Kazuya E-mail: Lukas.Hollenstein@unige.ch E-mail: Kazuya.Koyama@port.ac.uk

    2010-04-01

    Next generation surveys will observe the large-scale structure of the Universe with unprecedented accuracy. This will enable us to test the relationships between matter over-densities, the curvature perturbation and the Newtonian potential. Any large-distance modification of gravity or exotic nature of dark energy modifies these relationships as compared to those predicted in the standard smooth dark energy model based on General Relativity. In linear theory of structure growth such modifications are often parameterised by virtue of two functions of space and time that enter the relation of the curvature perturbation to, first, the matter over- density, and second, the Newtonian potential. We investigate the predictions for these functions in Brans-Dicke theory, clustering dark energy models and interacting dark energy models. We find that each theory has a distinct path in the parameter space of modified growth. Understanding these theoretical priors on the parameterisations of modified growth is essential to reveal the nature of cosmic acceleration with the help of upcoming observations of structure formation.

  13. DEVELOPMENT OF AN INSPECTION PLATFORM AND A SUITE OF SENSORS FOR ASSESSING CORROSION AND MECHANICAL DAMAGE ON UNPIGGABLE TRANSMISSION MAINS

    SciTech Connect (OSTI)

    George C. Vradis

    2003-07-01

    This development program is a joint effort among the Northeast Gas Association (formerly New York Gas Group), Foster-Miller, Inc., and the US Department of Energy (DOE) through the National Energy Technology Laboratory (NETL). The DOE's contribution to this project is $572,525 out of a total of $772,525. The present report summarizes the accomplishments of the project during its third three-month period (from April 2003 through June 2003). The project was initiated with delay in February 2003 due to contractual issues that emerged between NGA and Foster-Miller, Inc. The two organizations are working diligently to maintain the program's pace and expect to complete it in time. The efforts of the project focused during this period in finalizing the assessment of the tether technology, which is intended to be used as the means of communication between robot and operator. Results indicate that the tether is a viable option under certain pipeline operating conditions, but not all. Concerns also exist regarding the abrasion resistance of the tether, this issue being the last studied. Substantial work was also conducted on the design of the robotic platform, which has progressed very well. Finally, work on the MFL sensor, able to negotiate all pipeline obstacles (including plug valves), was initiated by PII following the successful completion of the subcontract negotiations between Foster-Miller and PII. The sensor design is at this point the critical path in the project's timetable.

  14. Characterizing Rat PNS Electrophysiological Response to Electrical Stimulation Using in vitro Chip-Based Human Investigational Platform (iCHIP)

    SciTech Connect (OSTI)

    Khani, Joshua; Prescod, Lindsay; Enright, Heather; Felix, Sarah; Osburn, Joanne; Wheeler, Elizabeth; Kulp, Kris

    2015-08-18

    Ex vivo systems and organ-on-a-chip technology offer an unprecedented approach to modeling the inner workings of the human body. The ultimate goal of LLNL’s in vitro Chip-based Human Investigational Platform (iCHIP) is to integrate multiple organ tissue cultures using microfluidic channels, multi-electrode arrays (MEA), and other biosensors in order to effectively simulate and study the responses and interactions of the major organs to chemical and physical stimulation. In this study, we focused on the peripheral nervous system (PNS) component of the iCHIP system. Specifically we sought to expound on prior research investigating the electrophysiological response of rat dorsal root ganglion cells (rDRGs) to chemical exposures, such as capsaicin. Our aim was to establish a protocol for electrical stimulation using the iCHIP device that would reliably elicit a characteristic response in rDRGs. By varying the parameters for both the stimulation properties – amplitude, phase width, phase shape, and stimulation/ return configuration – and the culture conditions – day in vitro and neural cell types - we were able to make several key observations and uncover a potential convention with a minimal number of devices tested. Future work will seek to establish a standard protocol for human DRGs in the iCHIP which will afford a portable, rapid method for determining the effects of toxins and novel therapeutics on the PNS.

  15. Design and package of a {sup 14}CO{sub 2} field analyzer The Global Monitor Platform (GMP)

    SciTech Connect (OSTI)

    Bright, Michelle; Marino, Bruno D.V.; Gronniger, Glen

    2011-08-01

    Carbon Capture and Sequestration (CCS) is widely accepted as a means to reduce and eliminate the fossil fuel CO{sub 2} (ff- CO{sub 2}) emissions from coal fired power plants. Success of CCS depends on near zero leakage rates over decadal time scales. Currently no commercial methods to determine leakage of ff-CO{sub 2} are available. The Global Monitor Platform (GMP) field analyzer provides high precision analysis of CO{sub 2} isotopes [12C (99%), 13C (<1%), 14C (1.2x10-10 %)] that can differentiate between fossil and biogenic CO{sub 2} emissions. Fossil fuels contain no {sup 14}C; their combustion should lower atmospheric amounts on local to global scales. There is a clear mandate for monitoring, verification and accounting (MVA) of CCS systems nationally and globally to verify CCS integrity, treaty verification (Kyoto Protocol) and to characterize the nuclear fuel cycle. Planetary Emissions Management (PEM), working with the National Secure Manufacturing Center (NSMC), has the goal of designing, ruggedizing and packaging the GMP for field deployment. The system will conduct atmosphere monitoring then adapt the system to monitor water and soil evaluations. Measuring {sup 14}CO{sub 2} in real time will provide quantitative concentration data for ff-CO{sub 2} in the atmosphere and CCS leakage detection. Initial results will be discussed along with design changes for improved detection sensitivity and manufacturability.

  16. Ag(I) Ion Functionalized Porous Organic Polymers As a New Platform for Highly Selective Adsorption of Ethylene over Ethane

    SciTech Connect (OSTI)

    LI, Baiyan; Zhang, Yiming; Ma, Dingxuan; Wu, Zili; Ma, Shengqian

    2014-01-01

    We report herein a strategy of incorporating air stable Ag(I) ions into water stable, high surface area porous organic polymer (POP) affording significant increase in ethylene uptake capacity and extremely high Qst for ethylene (over 100 kJ/mol at low ethylene load-ing) as illustrated in the context of Ag(I) ion functionalized PAF-1, PAF-1-SO3Ag. IAST calculations using single-component-isotherm data and equimolar ethylene/ethane ratio at 296 K reveal PAF-1-SO3Ag shows exceptionally high ethylene/ethane adsorption selectivi-ty (Sads: 27 to 125), far surpassing benchmark zeolite and any other MOF reported in literature. This alongside excellent water/air stability, high ethylene uptake capacity, and mild regeneration requirements make PAF-1-SO3Ag hold promise for adsorption-based eth-ylene/ethane separations, paving a way to develop Ag(I) ion function-alized POPs as a new platform for highly selective adsorption of eth-ylene over ethane.

  17. MR-Guided High-Intensity Focused Ultrasound Ablation of Breast Cancer with a Dedicated Breast Platform

    SciTech Connect (OSTI)

    Merckel, Laura G.; Bartels, Lambertus W.; Koehler, Max O.; Bongard, H. J. G. Desiree van den; Deckers, Roel; Mali, Willem P. Th. M.; Binkert, Christoph A.; Moonen, Chrit T.; Gilhuijs, Kenneth G. A. Bosch, Maurice A. A. J. van den

    2013-04-15

    Optimizing the treatment of breast cancer remains a major topic of interest. In current clinical practice, breast-conserving therapy is the standard of care for patients with localized breast cancer. Technological developments have fueled interest in less invasive breast cancer treatment. Magnetic resonance-guided high-intensity focused ultrasound (MR-HIFU) is a completely noninvasive ablation technique. Focused beams of ultrasound are used for ablation of the target lesion without disrupting the skin and subcutaneous tissues in the beam path. MRI is an excellent imaging method for tumor targeting, treatment monitoring, and evaluation of treatment results. The combination of HIFU and MR imaging offers an opportunity for image-guided ablation of breast cancer. Previous studies of MR-HIFU in breast cancer patients reported a limited efficacy, which hampered the clinical translation of this technique. These prior studies were performed without an MR-HIFU system specifically developed for breast cancer treatment. In this article, a novel and dedicated MR-HIFU breast platform is presented. This system has been designed for safe and effective MR-HIFU ablation of breast cancer. Furthermore, both clinical and technical challenges are discussed, which have to be solved before MR-HIFU ablation of breast cancer can be implemented in routine clinical practice.

  18. Ukraine-Capacity Building for Low Carbon Growth | Open Energy...

    Open Energy Info (EERE)

    Ukraine-Capacity Building for Low Carbon Growth (Redirected from UNDP-Capacity Building for Low Carbon Growth in Ukraine) Jump to: navigation, search Name UNDP-Capacity Building...

  19. Ukraine-Capacity Building for Low Carbon Growth | Open Energy...

    Open Energy Info (EERE)

    Ukraine-Capacity Building for Low Carbon Growth Jump to: navigation, search Name UNDP-Capacity Building for Low Carbon Growth in Ukraine AgencyCompany Organization United Nations...

  20. ALS Technique Gives Novel View of Lithium Battery Dendrite Growth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ALS Technique Gives Novel View of Lithium Battery Dendrite Growth ALS Technique Gives Novel View of Lithium Battery Dendrite Growth Print Thursday, 24 April 2014 09:46 Lithium-ion...