National Library of Energy BETA

Sample records for growth case comparisons

  1. Appendix B: Economic growth case comparisons

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    energy. See Table A17 for selected nonmarketed residential and commercial renewable energy data. 5 Includes non-biogenic municipal waste, liquid hydrogen, methanol, and some...

  2. A comparison of normal and worst case cement plant emissions

    SciTech Connect (OSTI)

    Woodford, J.; Gossman, D.; Johnson, N.

    1996-12-31

    Lone Star Industries, Inc. in Cape Girardeau, Missouri conducted a trial burn in October, 1995. Two metals emissions test days were conducted. One of the test days was a worst case metals spiking day and one of the test days was a normal emissions day. This paper examines and compares the emissions from these two test days. Much has been made of metals emissions from hazardous waste burning cement kilns, but for the most part, this has been due to the worst case metals emissions data that became available from the 1992 BIF compliance testing performed and reported by 24 cement plants. By comparison, very little data exists on normal cement kiln emissions. This paper provides one comparison.

  3. Comparison of continuous air monitor utilization: A case study

    SciTech Connect (OSTI)

    Rodgers, J.C.; Whicker, J.J.; Voss, J.T.

    1997-08-01

    The Chemical Metallurgy Research (CMR) building has been upgrading to different continuous air monitors (CAMs) over the past several years. During the transition, both the newer and older CAMs were positioned in the rooms for field testing and comparison. On December 19, 1996, an accidental release of plutonium aerosol occurred into a laboratory in the CMR building. The event occurred while the room was unoccupied, and no personnel were exposed from this incident. There were two fixed air samplers (FASs) and three CAMs operating in the room at the time the release occurred, including two of the recently installed Canberra Alpha Sentry CAMs and one older Eberline CAM. The apparent cause of the release was a procedure carried out in the basement involving the replacement of the HEPA filter in the ventilation exhaust of a slot-box in the laboratory. For a short period, the ventilation was disconnected from the slot-box in this room, but not from the chemical hood exhaust on the opposite side of the laboratory. Therefore, a condition was created where backflow could occur out of the slot-box and into the room. Eventually all three CAMs in the room alarmed, and the situation was successfully monitored and brought under control by health physics personnel. Data on CAM performance were logged, and Pu activity collected on CAM and FAS filters were measured. A comparison of the new and old continuous air monitoring programs was performed and many interesting lessons on CAM performance and CAM utilization were learned. Overall, this comparison showed the advantages of remote monitoring, timely spectral information, and concentration measurements resolved in time and space.

  4. DYNAMIC AND CLASSICAL PRA: A BWR SBO CASE COMPARISON

    SciTech Connect (OSTI)

    Mandelli, Diego; Smith, Curtis L; Ma, Zhegang

    2011-07-01

    As part of the Light-Water Sustainability Program (LWRS), the purpose of the Risk Informed Safety Margin Characterization (RISMC) Pathway research and development is to support plant decisions for risk-informed margin management with the aim to improve economics, reliability, and sustain the safety of current NPPs. In this paper, we describe the RISMC analysis process illustrating how mechanistic (i.e., dynamic system simulators) and probabilistic (stochastic sampling strategies) approaches are combined in a dynamic PRA fashion in order to estimate safety margins. We use the scenario of a station blackout (SBO) wherein offsite power and onsite power are lost, thereby causing a challenge to plant safety systems. We describe the RISMC approach, illustrate the station blackout modeling, and compare this with traditional risk analysis modeling for this type of accident scenario. In the RISMC approach the dataset obtained consists of set of simulation runs (performed by using codes such as RELAP5/3D) where timing and ordering of events is changed accordingly to the stochastic sampling strategy adopted. On the other side, classical PRA methods, which are based on event-tree (FT) and fault-tree (FT) structures, generate minimal cut sets and probability values associated to each ET branch. The comparison of the classical and RISMC approaches is performed not only in terms of overall core damage probability but also considering statistical differences in the actual sequence of events. The outcome of this comparison analysis shows similarities and dissimilarities between the approaches but also highlights the greater amount of information that can be generated by using the RISMC approach.

  5. Linking atomistic and mesoscale simulations of nanocrystalline materials : quantitative validation for the case of grain growth.

    SciTech Connect (OSTI)

    Moldovan, D.; Wolf, D.; Phillpot, S. R.; Materials Science Division; Louisiana State Univ.

    2003-11-01

    Using grain growth in nanocrystalline palladium as a simple case study, we demonstrate how a novel mesoscale approach for simulating microstructural evolution in polycrystalline materials can be validated directly against atomic-level simulations of the same system. We first describe molecular dynamics simulations of grain growth in a columnar model microstructure. The atomic-level insights into the grain-growth mechanism gained from these simulations, particularly in the role of grain rotations, are captured theoretically for incorporation into the mesoscale approach, in which the objects evolving in space and time are the grain boundaries and grain junctions rather than the atoms. With all the input parameters to the mesoscale being physically well defined and obtained directly from the atomic-level simulations, the mesoscale simulations are fully prescribed. We find that the morphology of the mesoscale system evolves in an almost identical manner with that of the molecular dynamics simulation, demonstrating that the length- and time-scale linking has been performed correctly. When applied to systems containing large numbers of grains, the now validated mesoscale simulation approach allows the growth topology and long-time growth kinetics to be determined. As an outlook, we describe how the effects of applied stress can be incorporated.

  6. Direct Comparison of Inverted and Non-Inverted Growths of GaInP Solar Cells: Preprint

    SciTech Connect (OSTI)

    Steiner, M. A.; Geisz, J. F.; Reedy Jr, R.C.; Kurtz, S.

    2008-05-01

    The inverted growth of III-V solar cells presents some specific challenges that are not present in regular, non-inverted growths. Because the highly doped top contact layer is grown first, followed by the lengthy high-temperature growth of the remainder of the structure, there is ample time for the dopants in the contact layer to diffuse away. This leads to an increase in the contact resistance to the top layer, and a corresponding drop in voltage. The diffusion of dopants in other layers is similarly altered with respect to the non-inverted configuration because of the change in growth sequence. We compare the dopant profiles of inverted and non-inverted structures by using secondary ion mass spectroscopy and correlate the results with the observed performance of the devices. We also describe a technique for growing a GaInAsN contact layer in the inverted configuration and show that it achieves a specific contact resistance comparable to what is normally observed in non-inverted cells.

  7. Cost comparison between private and public collection of residual household waste: Multiple case studies in the Flemish region of Belgium

    SciTech Connect (OSTI)

    Jacobsen, R.; Buysse, J.; Gellynck, X.

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer The goal is to compare collection costs for residual household waste. Black-Right-Pointing-Pointer We have clustered all municipalities in order to find mutual comparable pairs. Black-Right-Pointing-Pointer Each pair consists of one private and one public operating waste collection program. Black-Right-Pointing-Pointer All cases show that private service has lower costs than public service. Black-Right-Pointing-Pointer Municipalities were contacted to identify the deeper causes for the waste management program. - Abstract: The rising pressure in terms of cost efficiency on public services pushes governments to transfer part of those services to the private sector. A trend towards more privatizing can be noticed in the collection of municipal household waste. This paper reports the findings of a research project aiming to compare the cost between the service of private and public collection of residual household waste. Multiple case studies of municipalities about the Flemish region of Belgium were conducted. Data concerning the year 2009 were gathered through in-depth interviews in 2010. In total 12 municipalities were investigated, divided into three mutual comparable pairs with a weekly and three mutual comparable pairs with a fortnightly residual waste collection. The results give a rough indication that in all cases the cost of private service is lower than public service in the collection of household waste. Albeit that there is an interest in establishing whether there are differences in the costs and service levels between public and private waste collection services, there are clear difficulties in establishing comparisons that can be made without having to rely on a large number of assumptions and corrections. However, given the cost difference, it remains the responsibility of the municipalities to decide upon the service they offer their citizens, regardless the cost efficiency: public or private.

  8. A comparison of surface topography characterization technologies for use in comparing spent bullet and cartridge case signatures

    SciTech Connect (OSTI)

    Batishko, C.R.; Hickman, B.J.; Cuta, F.M.

    1992-11-01

    The Pacific Northwest Laboratory was tasked by the US Department of Energy to provide technical assistance to the Federal Bureau of Investigation in evaluating and ranking technologies potentially useful in high-speed comparison of unique spent bullet and cartridge case surface signatures. Information sources included vendor input, current relevant literature, vendor phone contacts, other FBI resources, relevant PNL reports, and personal contact with numerous PNL technical staff. A comprehensive list of technologies was reduced to a list of 38 by grouping very similar methodologies, and further reduced to a short list of six by applying a set of five minimum functional requirements. A total of 14 primary criteria, many having secondary criteria, were subsequently used to evaluate each technology. The ranked short list results are reported and supported in this document, and their scores normalized to a hypothetical ideal system are as follows: (1) confocal microscopy 82.13; (2) laser dynamic focusing 72.04; (3)moire interferometry V70.94; (4)fringe field capacitance;(5)laser triangulation 66.18; (6)structured/sectioned light 65.55. Information available within the time/budget constraints which was used for the evaluation and ranking was not sufficiently detailed to evaluate specific implementations of the technologies. Each of the technologies in the short list was judged potentially capable of meeting the minimum requirements. Clever, novel engineering solutions resulting in a more cost-effective system, or a closer fit to the ``ideal system,`` could result in a reordering of the short list when actual technical proposals are evaluated. Therefore, it is recommended that a Request for Proposal not be limited to only the highest ranked technology, but include all six technologies in the short list.

  9. A comparison of surface topography characterization technologies for use in comparing spent bullet and cartridge case signatures

    SciTech Connect (OSTI)

    Batishko, C.R.; Hickman, B.J.; Cuta, F.M.

    1992-11-01

    The Pacific Northwest Laboratory was tasked by the US Department of Energy to provide technical assistance to the Federal Bureau of Investigation in evaluating and ranking technologies potentially useful in high-speed comparison of unique spent bullet and cartridge case surface signatures. Information sources included vendor input, current relevant literature, vendor phone contacts, other FBI resources, relevant PNL reports, and personal contact with numerous PNL technical staff. A comprehensive list of technologies was reduced to a list of 38 by grouping very similar methodologies, and further reduced to a short list of six by applying a set of five minimum functional requirements. A total of 14 primary criteria, many having secondary criteria, were subsequently used to evaluate each technology. The ranked short list results are reported and supported in this document, and their scores normalized to a hypothetical ideal system are as follows: (1) confocal microscopy 82.13; (2) laser dynamic focusing 72.04; (3)moire interferometry V70.94; (4)fringe field capacitance;(5)laser triangulation 66.18; (6)structured/sectioned light 65.55. Information available within the time/budget constraints which was used for the evaluation and ranking was not sufficiently detailed to evaluate specific implementations of the technologies. Each of the technologies in the short list was judged potentially capable of meeting the minimum requirements. Clever, novel engineering solutions resulting in a more cost-effective system, or a closer fit to the ideal system,'' could result in a reordering of the short list when actual technical proposals are evaluated. Therefore, it is recommended that a Request for Proposal not be limited to only the highest ranked technology, but include all six technologies in the short list.

  10. Comparison of horizontal load transfer curves for laterally loaded piles from strain gages and slope inclinometer: A case study

    SciTech Connect (OSTI)

    Pinto, P.L.; Anderson, B.; Townsend, F.C.

    1999-07-01

    Laterally loaded deep foundations are commonly analyzed using the Winkler model with the soil-pile interaction modeled through nonlinear springs in the form of p-y curves. Computer programs such as FloridaPier and COM624P use default p-y curves when performing lateral analyses. These curves are based on input soil properties such as subgrade modulus, friction angle, undrained shear strength, etc. Soil properties must be deduced by laboratory testing or correlation to in situ test results. This is a source of uncertainty. In a few cases, lateral load tests are performed on instrumented piles, and the validity of such assumptions can be assessed. Test piles are commonly instrumented with strain gages and/or inclinometers. P-y curves can be back computed from these data, and the curves obtained with the two methods should agree closely. Results from a field test on a concrete pile are presented and the critical factors for the analysis are discussed. One added difficulty with concrete is its nonlinear behavior particularly near structural failure. The curves obtained are also compared with those developed from the Dilatometer/Cone Pressuremeter Test and the Standard Penetration Test.

  11. Compiler Comparisons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Comparisons Compiler Comparisons Compiler Comparisons on Hopper There are five compilers available to users on Hopper, the NERSC XE6. All of the compilers on this system are...

  12. Comparison of growth texture in round Bi2212 and flat Bi2223 wires and its relation to high critical current density development

    SciTech Connect (OSTI)

    Kametani, F.; Jiang, J.; Matras, M.; Abraimov, D.; Hellstrom, E. E.; Larbalestier, D. C.

    2015-02-10

    Why Bi₂Sr₂CaCu₂Ox (Bi2212) allows high critical current density Jc in round wires rather than only in the anisotropic tape form demanded by all other high temperature superconductors is important for future magnet applications. Here we compare the local texture of state-of-the-art Bi2212 and Bi2223 ((Bi,Pb)₂Sr₂Ca₂Cu₃O₁₀), finding that round wire Bi2212 generates a dominant a-axis growth texture that also enforces a local biaxial texture (FWHM <15°) while simultaneously allowing the c-axes of its polycrystals to rotate azimuthally along and about the filament axis so as to generate macroscopically isotropic behavior. By contrast Bi2223 shows only a uniaxial (FWHM <15°) c-axis texture perpendicular to the tape plane without any in-plane texture. Consistent with these observations, a marked, field-increasing, field-decreasing Jc(H) hysteresis characteristic of weak-linked systems appears in Bi2223 but is absent in Bi2212 round wire. Growth-induced texture on cooling from the melt step of the Bi2212 Jc optimization process appears to be the key step in generating this highly desirable microstructure.

  13. Comparison of growth texture in round Bi2212 and flat Bi2223 wires and its relation to high critical current density development

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Kametani, F.; Jiang, J.; Matras, M.; Abraimov, D.; Hellstrom, E. E.; Larbalestier, D. C.

    2015-02-10

    Why Bi₂Sr₂CaCu₂Ox (Bi2212) allows high critical current density Jc in round wires rather than only in the anisotropic tape form demanded by all other high temperature superconductors is important for future magnet applications. Here we compare the local texture of state-of-the-art Bi2212 and Bi2223 ((Bi,Pb)₂Sr₂Ca₂Cu₃O₁₀), finding that round wire Bi2212 generates a dominant a-axis growth texture that also enforces a local biaxial texture (FWHM <15°) while simultaneously allowing the c-axes of its polycrystals to rotate azimuthally along and about the filament axis so as to generate macroscopically isotropic behavior. By contrast Bi2223 shows only a uniaxial (FWHM <15°) c-axis texturemore » perpendicular to the tape plane without any in-plane texture. Consistent with these observations, a marked, field-increasing, field-decreasing Jc(H) hysteresis characteristic of weak-linked systems appears in Bi2223 but is absent in Bi2212 round wire. Growth-induced texture on cooling from the melt step of the Bi2212 Jc optimization process appears to be the key step in generating this highly desirable microstructure.« less

  14. Appendix C: Price case comparisons

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    High oil price Low oil price Reference High oil price Low oil price Reference High oil price Production Crude oil and lease condensate ... 13.87 19.06 20.36...

  15. A comparison of Nannochloropsis salina growth performance in two outdoor pond designs: conventional raceways versus the ARID pond with superior temperature management

    SciTech Connect (OSTI)

    Crowe, Braden J.; Attalah, Said; Agrawal, Shweta; Waller, Peter; Ryan, Randy; Van Wagenen, Jonathan M.; Chavis, Aaron R.; Kyndt, John; Kacira, Murat; Ogden, Kimberly L.; Huesemann, Michael H.

    2012-10-01

    The present study examines how climatic conditions and pond design affect the growth performance of microalgae. From January to April of 2011, outdoor batch cultures of Nannochloropsis salina were grown in three replicate 780 L conventional raceways, as well as in an experimental 7500 L ARID (Algae Raceway Integrated Design) pond. The ARID culture system utilizes a series of 8 to 20 cm deep basins and a 1.5 m deep canal to enhance light exposure and mitigate temperature variations and extremes. The ARID culture reached the stationary phase 27 days earlier than the conventional raceways, which can be attributed to its superior temperature management and shallower basins. On a night when the air temperature dropped to -9 C, the water temperature was 18 C higher in the ARID pond than in the conventional raceways. Lipid and fatty acid content ranged from 16 - 25 % and 5 - 15 %, respectively, as a percentage of AFDW. Palmitic, palmitoleic, and eicosapentaenoic acid comprised the majority of fatty acids. While the ARID culture system achieved nearly double the volumetric productivity relative to the conventional raceways (0.023 vs 0.013 g L-1day-1), areal biomass productivities were of similar magnitude in both pond systems (3.34 vs. 3.47 g m-2day-1), suggesting that the ARID pond design has to be further optimized, most likely by increasing the culture depth or operating at higher cell densities while maintaining adequate mixing.

  16. A Comparison of Nannochloropsis salina Growth Performance in Two Outdoor Pond Designs: Conventional Raceways versus the ARID Pond with Superior Temperature Management

    SciTech Connect (OSTI)

    Crowe, Braden; Attalah, Said; Agrawal, Shweta; Waller, Peter; Ryan, Randy; Van Wagenen, Jon; Chavis, Aaron; Kyndt, John; Kacira, Murat; Ogden, Kim L.; Huesemann, Michael

    2012-01-01

    The present study examines how climatic conditions and pond design affect the growth performance of microalgae. From January to April of 2011, outdoor batch cultures of Nannochloropsis salina were grown in three replicate 780 L conventional raceways, as well as in an experimental 7500 L algae raceway integrated design (ARID) pond. The ARID culture system utilizes a series of 8-20 cm deep basins and a 1.5 m deep canal to enhance light exposure and mitigate temperature variations and extremes. The ARID culture reached the stationary phase 27 days earlier than the conventional raceways, which can be attributed to its superior temperature management and shallower basins. On a night when the air temperature dropped to -9C, the water temperature was 18C higher in the ARID pond than in the conventional raceways. Lipid and fatty acid content ranged from 16 to 25% and from 5 to15%, respectively, as a percentage of AFDW. Palmitic, palmitoleic, and eicosapentaenoic acids comprised the majority of fatty acids. While the ARID culture system achieved nearly double the volumetric productivity relative to the conventional raceways (0.023 versus 0.013 g L-1day-1), areal biomass productivities were of similar magnitude in both pond systems (3.47 versus 3.34 g m-2day-1), suggesting that the ARID pond design has to be further optimized, most likely by increasing the culture depth or operating at higher cell densities while maintaining adequate mixing.

  17. A Comparison of Nannochloropsis salina Growth Performance in Two Outdoor Pond Designs: Conventional Raceways versus the ARID Pond with Superior Temperature Management

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Crowe, Braden; Attalah, Said; Agrawal, Shweta; Waller, Peter; Ryan, Randy; Van Wagenen, Jon; Chavis, Aaron; Kyndt, John; Kacira, Murat; Ogden, Kim L.; et al

    2012-01-01

    The present study examines how climatic conditions and pond design affect the growth performance of microalgae. From January to April of 2011, outdoor batch cultures of Nannochloropsis salina were grown in three replicate 780 L conventional raceways, as well as in an experimental 7500 L algae raceway integrated design (ARID) pond. The ARID culture system utilizes a series of 8-20 cm deep basins and a 1.5 m deep canal to enhance light exposure and mitigate temperature variations and extremes. The ARID culture reached the stationary phase 27 days earlier than the conventional raceways, which can be attributed to its superiormore » temperature management and shallower basins. On a night when the air temperature dropped to -9°C, the water temperature was 18°C higher in the ARID pond than in the conventional raceways. Lipid and fatty acid content ranged from 16 to 25% and from 5 to15%, respectively, as a percentage of AFDW. Palmitic, palmitoleic, and eicosapentaenoic acids comprised the majority of fatty acids. While the ARID culture system achieved nearly double the volumetric productivity relative to the conventional raceways (0.023 versus 0.013 g L-1day-1), areal biomass productivities were of similar magnitude in both pond systems (3.47 versus 3.34 g m-2day-1), suggesting that the ARID pond design has to be further optimized, most likely by increasing the culture depth or operating at higher cell densities while maintaining adequate mixing.« less

  18. Comparison of Methods for Estimating the NOx Emission Impacts of Energy Efficiency and Renewable Energy Projects: Shreveport, Louisiana Case Study (Revised)

    SciTech Connect (OSTI)

    Chambers, A.; Kline, D. M.; Vimmerstedt, L.; Diem, A.; Dismukes, D.; Mesyanzhinov, D.

    2005-07-01

    This is a case study comparing methods of estimating the NOx emission impacts of energy efficiency and renewable energy projects in Shreveport, Louisiana.

  19. Compiler Comparisons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Compiler Comparisons Compiler Comparisons Compiler Comparisons on Hopper There are five compilers available to users on Hopper, the NERSC XE6. All of the compilers on this system are provided by Cray, and they are invoked with wrapper modules that ensure that each compiler links with the proper system and MPI libraries. Each of the compilers have a wide variety of options that control the level of optimization of the exectuable code they produce. We have collected several optimization

  20. Compiler Comparisons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Comparisons Compiler Comparisons Using a set of benchmarks described below, different optimization options for the different compilers on Edison are compared. The compilers are also compared against one another on the benchmarks. Benchmarks used Using a set of benchmarks described below, different optimization options for the different compilers on Edison. The compilers are also compared against one another on the benchmarks. NERSC6 Benchmarks We used these benchmarks from the NERSC6

  1. Comparison of crystal growth and thermoelectric properties of n-type Bi-Se-Te and p-type Bi-Sb-Te nanocrystalline thin films: Effects of homogeneous irradiation with an electron beam

    SciTech Connect (OSTI)

    Takashiri, Masayuki, E-mail: takashiri@tokai-u.jp; Imai, Kazuo; Uyama, Masato; Nishi, Yoshitake [Department of Materials Science, Tokai University, 4-1-1 Kitakaname, Hiratsuka, Kanagawa 259-1292 (Japan); Hagino, Harutoshi; Miyazaki, Koji [Department of Mechanical and Control Engineering, Kyushu Institute of Technology, 1-1 Sensui, Tobata-ku, Kitakyushu 804-8550 (Japan); Tanaka, Saburo [Department of Mechanical Engineering, College of Engineering, Nihon University, Nakagawara, Tokusada, Tamuramachi, Koriyama, Fukushima 963-8642 (Japan)

    2014-06-07

    The effects of homogenous electron beam (EB) irradiation on the crystal growth and thermoelectric properties of n-type Bi-Se-Te and p-type Bi-Sb-Te thin films were investigated. Both types of thin films were prepared by flash evaporation, after which homogeneous EB irradiation was performed at an acceleration voltage of 0.17?MeV. For the n-type thin films, nanodots with a diameter of less than 10?nm were observed on the surface of rice-like nanostructures, and crystallization and crystal orientation were improved by EB irradiation. The resulting enhancement of mobility led to increased electrical conductivity and thermoelectric power factor for the n-type thin films. In contrast, the crystallization and crystal orientation of the p-type thin films were not influenced by EB irradiation. The carrier concentration increased and mobility decreased with increased EB irradiation dose, possibly because of the generation of defects. As a result, the thermoelectric power factor of p-type thin films was not improved by EB irradiation. The different crystallization behavior of the n-type and p-type thin films is attributed to atomic rearrangement during EB irradiation. Selenium in the n-type thin films is more likely to undergo atomic rearrangement than the other atoms present, so only the crystallinity of the n-type Bi-Se-Te thin films was enhanced.

  2. Surfactant assisted growth of MgO films on GaN

    SciTech Connect (OSTI)

    Paisley, E. A.; Shelton, T. C.; Collazo, R.; Sitar, Z.; Maria, J.-P.; Christen, H. M.; Biegalski, M. D.; Mita, S.

    2012-08-27

    Thin epitaxial films of <111> oriented MgO on [0001]-oriented GaN were grown by molecular beam epitaxy and pulsed laser deposition using the assistance of a vapor phase surfactant. In both cases, surfactant incorporation enabled layer-by-layer growth and a smooth terminal surface by stabilizing the {l_brace}111{r_brace} rocksalt facet. Metal-insulator-semiconductor capacitor structures were fabricated on n-type GaN. A comparison of leakage current density for conventional and surfactant-assisted growth reveals a nearly 100 Multiplication-Sign reduction in leakage current density for the surfactant-assisted samples. These data verify numerous predictions regarding the role of H-termination in regulating the habit of rocksalt crystals.

  3. Case Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    OSCARS Case Studies Science DMZ Case Studies Multi-facility Workflow Case Study News & Publications ESnet News Publications and Presentations Galleries ESnet Awards and Honors Blog...

  4. Case Studies

    Broader source: Energy.gov [DOE]

    The following case studies are examples of integrating renewable energy into Federal new construction and major renovation projects. Additional renewable energy case studies are also available.

  5. Surfactant assisted growth of MgO films on GaN

    SciTech Connect (OSTI)

    Paisley, Elisibeth A.; Shelton, T C; Mita, S; Gaddy, Brian E.; Irving, D L; Christen, Hans M; Sitar, Z; Biegalski, Michael D; Maria, Jon Paul

    2012-01-01

    Thin epitaxial films of <111> oriented MgO on [0001]-oriented GaN were grown by molecular beam epitaxy (MBE) and pulsed laser deposition (PLD) using the assistance of a vapor phase surfactant. In both cases, surfactant incorporation enabled layer-by-layer growth and a smooth terminal surface due to stabilizing the {111} rocksalt facet. MBE growth of MgO in water terminates after several monolayers, and is attributed to saturation of surface active sites needed to facilitate the Mg oxidation reaction. MgO films prepared by PLD grow continuously, this occurs due to the presence of excited oxidizing species in the laser plasma eliminate the need for catalytic surface sites. Metal-insulator-semiconductor capacitor structures were fabricated on n-type GaN. A comparison of leakage current density for conventional and surfactant-assisted growth reveals a nearly two order of magnitude reduction in leakage current density for the smoother surfactant-assisted samples. Collectively, these data verify numerous predictions and calculations regarding the role of H-termination in regulating the habit of MgO crystals.

  6. Case Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Case Studies Case Studies The following case studies will be included in the HEP report. Final case studies are due January 7, 2013. Lattice Gauge Theories - Lead: Doug Toussaint Simulations for Cosmic Frontier Experiments - Leads: Peter Nugent & Andrew Connelly Cosmic Microwave Background Data Analysis - Lead: Julian Borrill Cosmological Simulations - Lead: Salman Habib Plasma Accelerator Simulation Using Laser and Particle Beam Drivers - Leads: Cameron Geddes & Frank Tsung Community

  7. Validating hydrodynamic growth in National Ignition Facility implosions

    SciTech Connect (OSTI)

    Peterson, J. L. Casey, D. T.; Hurricane, O. A.; Raman, K. S.; Robey, H. F.; Smalyuk, V. A.

    2015-05-15

    We present new hydrodynamic growth experiments at the National Ignition Facility, which extend previous measurements up to Legendre mode 160 and convergence ratio 4, continuing the growth factor dispersion curve comparison of the low foot and high foot pulses reported by Casey et al. [Phys. Rev. E 90, 011102(R) (2014)]. We show that the high foot pulse has lower growth factor and lower growth rate than the low foot pulse. Using novel on-capsule fiducial markers, we observe that mode 160 inverts sign (changes phase) for the high foot pulse, evidence of amplitude oscillations during the Richtmyer-Meshkov phase of a spherically convergent system. Post-shot simulations are consistent with the experimental measurements for all but the shortest wavelength perturbations, reinforcing the validity of radiation hydrodynamic simulations of ablation front growth in inertial confinement fusion capsules.

  8. Growth, microstructure, and luminescent

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    In and Ga adatoms, being more mobile, preferentially attach to steps. Step-flow growth prop- agates the InGa rich superstep and results in the creation of long continuous...

  9. FGF growth factor analogs

    DOE Patents [OSTI]

    Zamora, Paul O.; Pena, Louis A.; Lin, Xinhua; Takahashi, Kazuyuki

    2012-07-24

    The present invention provides a fibroblast growth factor heparin-binding analog of the formula: ##STR00001## where R.sub.1, R.sub.2, R.sub.3, R.sub.4, R.sub.5, X, Y and Z are as defined, pharmaceutical compositions, coating compositions and medical devices including the fibroblast growth factor heparin-binding analog of the foregoing formula, and methods and uses thereof.

  10. Smart Cities - Smart Growth

    Energy Savers [EERE]

    Smart Cities - Smart Growth The United States Secretaries of Commerce will co-lead a Business Development Mission to China from April 12-17, 2015. This mission will promote U.S. clean technology products and services in the areas of green building/construction, energy efficiency, carbon capture, utilization and storage (CCUS) and environmental technologies in support of the Smart Cities-Smart Growth theme. On November 12, President Obama and President Xi jointly announced the two countries'

  11. Well having inhibited microbial growth

    DOE Patents [OSTI]

    Lee, Brady D.; Dooley, Kirk J.

    2006-08-15

    The invention includes methods of inhibiting microbial growth in a well. A packing material containing a mixture of a first material and an antimicrobial agent is provided to at least partially fill a well bore. One or more access tubes are provided in an annular space around a casing within the well bore. The access tubes have a first terminal opening located at or above a ground surface and have a length that extends from the first terminal opening at least part of the depth of the well bore. The access tubes have a second terminal opening located within the well bore. An antimicrobial material is supplied into the well bore through the first terminal opening of the access tubes. The invention also includes well constructs.

  12. Distributed Wind Policy Comparison Tool

    SciTech Connect (OSTI)

    2011-12-01

    Power through Policy: 'Best Practices' for Cost-Effective Distributed Wind is a U.S. Department of Energy (DOE)-funded project to identify distributed wind technology policy best practices and to help policymakers, utilities, advocates, and consumers examine their effectiveness using a pro forma model. Incorporating a customized feed from the Database of State Incentives for Renewables and Efficiency (DSIRE), the Web-based Distributed Wind Policy Comparison Tool (Policy Tool) is designed to assist state, local, and utility officials in understanding the financial impacts of different policy options to help reduce the cost of distributed wind technologies. The Policy Tool can be used to evaluate the ways that a variety of federal and state policies and incentives impact the economics of distributed wind (and subsequently its expected market growth). It also allows policymakers to determine the impact of policy options, addressing market challenges identified in the U.S. DOEs '20% Wind Energy by 2030' report and helping to meet COE targets.

  13. Plant growth promoting rhizobacterium

    DOE Patents [OSTI]

    Doktycz, Mitchel John; Pelletier, Dale A.; Schadt, Christopher Warren; Tuskan, Gerald A.; Weston, David

    2015-08-11

    The present invention is directed to the Pseudomonas fluorescens strain GM30 deposited under ATCC Accession No. PTA-13340, compositions containing the GM30 strain, and methods of using the GM30 strain to enhance plant growth and/or enhance plant resistance to pathogens.

  14. Patent: Conditioning biomass for microbial growth | DOEpatents

    Office of Scientific and Technical Information (OSTI)

    Conditioning biomass for microbial growth Citation Details Title: Conditioning biomass for microbial growth

  15. NREL Industry Growth Forum Attracts Clean Energy Entrepreneurs and

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Investors - News Releases | NREL Industry Growth Forum Attracts Clean Energy Entrepreneurs and Investors Forum to feature business presentations from 30 clean energy startups, networking opportunities, compelling panels and speakers September 19, 2014 Thirty clean energy companies will present their business cases to a panel of investors and industry experts Oct. 28 and 29 in Denver, as the Energy Department's National Renewable Energy Laboratory (NREL) hosts its annual Industry Growth

  16. NREL Industry Growth Forum Attracts Clean Energy Startups and Investors -

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    News Releases | NREL Industry Growth Forum Attracts Clean Energy Startups and Investors Forum to feature business presentations from 30 clean energy startups, networking opportunities, panels and speakers featuring industry experts September 8, 2015 Thirty clean energy companies will present their business cases to a panel of investors and industry experts Nov. 3 and 4 in Denver, Colorado, as the Energy Department's National Renewable Energy Laboratory (NREL) hosts its annual Industry Growth

  17. NREL's Industry Growth Forum Brings Together Energy Innovators - News

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Releases | NREL NREL's Industry Growth Forum Brings Together Energy Innovators Event Highlights Clean Energy Technologies and Startup Businesses October 25, 2012 The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) 25th Industry Growth Forum this week attracted nearly 400 investors, entrepreneurs, scientists and policymakers to Denver. The two-day forum highlighted clean energy industry technology and business developments. In addition to hearing business case

  18. Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Development | Department of Energy Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure Development Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure Development Presented at Refueling Infrastructure for Alternative Fuel Vehicles: Lessons Learned for Hydrogen Conference, April 2-3, 2008, Sacramento, California PDF icon yborra.pdf More Documents & Publications asdfadfasfd The Compelling Case for Natural Gas Vehicles QER - Comment of American Gas

  19. Electrochemical Solution Growth: Gallium Nitride Crystal Growth - Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovation Portal Vehicles and Fuels Vehicles and Fuels Building Energy Efficiency Building Energy Efficiency Find More Like This Return to Search Electrochemical Solution Growth: Gallium Nitride Crystal Growth Sandia National Laboratories Contact SNL About This Technology Publications: PDF Document Publication Market Sheet (886 KB) Technology Marketing SummarySandia National Laboratories has developed a disruptive new crystal growth technology, called Electrochemical Solution Growth (ESG).

  20. Growth in Solar Means Growth in Ohio | Department of Energy

    Office of Environmental Management (EM)

    Growth in Solar Means Growth in Ohio Growth in Solar Means Growth in Ohio October 6, 2010 - 2:26pm Addthis Lorelei Laird Writer, Energy Empowers Editor's Note: Yesterday Secretary Chu announced that solar panels and a solar hot water heater will be added to the White House by the end of next spring. This entry is cross-posted from the Energy Empowers blog and deals with how the continued growth of solar power is not only a boon for industry, but for local economies as well. The solar industry

  1. Philippines' downstream sector poised for growth

    SciTech Connect (OSTI)

    Not Available

    1992-05-11

    This paper reports that the Philippines' downstream sector is poised for sharp growth. Despite a slip in refined products demand in recent years, Philippines products demand will rebound sharply by 2000, East-West Center (EWC), Honolulu, predicts. Philippines planned refinery expansions are expected to meet that added demand, EWC Director Fereidun Fesharaki says. Like the rest of the Asia-Pacific region, product specifications are changing, but major refiners in the area expect to meet the changes without major case outlays. At the same time, Fesharaki says, push toward deregulation will further bolster the outlook for the Philippines downstream sector.

  2. Global Green Growth Institute | Open Energy Information

    Open Energy Info (EERE)

    Growth Institute Redirect page Jump to: navigation, search REDIRECT Green Growth Strategy Support Retrieved from "http:en.openei.orgwindex.php?titleGlobalGreenGrowthIn...

  3. Long History of IAM Comparisons

    SciTech Connect (OSTI)

    Smith, Steven J.; Clarke, Leon E.; Edmonds, James A.; Kejun, Jiang; Kriegler, Elmar; Masui, Toshihiko; Riahi, Keywan; Shukla, Priyadarshi R.; Tavoni, Massimo; Van Vuuren, Detlef; Weyant, John

    2015-04-23

    Correspondence to editor: We agree with the editors that the assumptions behind models of all types, including integrated assessment models (IAMs), should be as transparent as possible. The editors were in error, however, when they implied that the IAM community is just now emulating the efforts of climate researchers by instigating their own model inter-comparison projects (MIPs). In fact, model comparisons for integrated assessment and climate models followed a remarkably similar trajectory. Early General Circulation Model (GCM) comparison efforts, evolved to the first Atmospheric Model Inter-comparison Project (AMIP), which was initiated in the early 1990s. Atmospheric models evolved to coupled atmosphere-ocean models (AOGCMs) and results from the first Coupled Model Inter-Comparison Project (CMIP1) become available about a decade later. Results of first energy model comparison exercise, conducted under the auspices of the Stanford Energy Modeling Forum, were published in 1977. A summary of the first comparison focused on climate change was published in 1993. As energy models were coupled to simple economic and climate models to form IAMs, the first comparison exercise for IAMs (EMF-14) was initiated in 1994, and IAM comparison exercises have been on-going since this time.

  4. Glovebox decontamination technology comparison

    SciTech Connect (OSTI)

    Quintana, D.M.; Rodriguez, J.B.; Cournoyer, M.E.

    1999-09-26

    Reconfiguration of the CMR Building and TA-55 Plutonium Facility for mission requirements will require the disposal or recycle of 200--300 gloveboxes or open front hoods. These gloveboxes and open front hoods must be decontaminated to meet discharge limits for Low Level Waste. Gloveboxes and open front hoods at CMR have been painted. One of the deliverables on this project is to identify the best method for stripping the paint from large numbers of gloveboxes. Four methods being considered are the following: conventional paint stripping, dry ice pellets, strippable coatings, and high pressure water technology. The advantages of each technology will be discussed. Last, cost comparisons between the technologies will be presented.

  5. Comparison with Carrier Multiplication

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Complete Theory of Down-Conversion, and a Comparison with Carrier Multiplication 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 22 24 26 28 30 32 34 Measured Quantum Efficiency (QE) Efficiency [%] with Down-Conversion Single- Junction Threshold Solar Cell 1 2 3 4 5 6 7 8 9 10 20 30 40 50 60 70 80 90 Peak Efficiency [%] Splitting Multiplicity (M) C=max C=1000 C=100 C=1 C=10 Down Conversion Carrier Multiplication Ze'ev R. Abrams, Avi Niv, Majid Gharghi, Chris Gladden & Xiang Zhang Materials Science

  6. EIA Report Estimates Growth of U.S. Energy Economy Through 2040

    Broader source: Energy.gov [DOE]

    Curious about what the U.S. energy economy might look like in 2040? EIA just released the Annual Energy Outlook Reference Case, containing projections about the growth of energy production and consumption over the next several decades.

  7. NREL's Industry Growth Forum Attracts Clean Energy Investors - News

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Releases | NREL NREL's Industry Growth Forum Attracts Clean Energy Investors 22nd Forum to Feature 34 Clean Energy Companies October 9, 2008 Thirty-four clean energy companies will present their business cases to a panel of investors and industry experts in Denver Nov. 3-5 as the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) hosts the 22nd NREL Industry Growth Forum. The 34 companies were selected through an application and review process and will compete for the

  8. NREL's Industry Growth Forum Attracts Clean Energy Investors - News

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Releases | NREL NREL's Industry Growth Forum Attracts Clean Energy Investors 25th Forum to Feature 30 Clean Energy Companies September 17, 2012 Thirty clean energy companies will present their business cases to a panel of investors and industry experts in Denver Oct. 23-24 as the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) hosts the 25th NREL Industry Growth Forum. The 30 companies were selected through an application and review process and will compete for the

  9. Comparison of Methods for Calculating Radiative Heat Transfer

    SciTech Connect (OSTI)

    Schock, Alfred; Abbate, M J

    2012-01-19

    Various approximations for calculating radioactive heat transfer between parallel surfaces are evaluated. This is done by applying the approximations based on total emissivities to a special case of known spectral emissivities, for which exact heat transfer calculations are possible. Comparison of results indicates that the best approximation is obtained by basing the emissivity of the receiving surface primarily on the temperature of the emitter. A specific model is shown to give excellent agreement over a very wide range of values.

  10. Isotropic Monte Carlo Grain Growth

    Energy Science and Technology Software Center (OSTI)

    2013-04-25

    IMCGG performs Monte Carlo simulations of normal grain growth in metals on a hexagonal grid in two dimensions with periodic boundary conditions. This may be performed with either an isotropic or a misorientation - and incliantion-dependent grain boundary energy.

  11. Comparison of ethanol production by different Zymomonas strains

    SciTech Connect (OSTI)

    Skotnicki, M.L.; Lee, K.J.; Tribe, D.E.; Rogers, P.L.

    1981-04-01

    A comparison of the rates of growth and ethanol production by 11 different strains of Zymomonas revealed a wide range of characteristics, with some strains being more tolerant of high sugar or ethanol concentrations and high incubation temperatures than others. Some strains were unable to utilize sucrose; others produced large amounts of levan, and one strain grew well but produced no levan. One strain, CP4, was considerably better in all respects than most of the other strains and was chosen as a starting strain for genetic improvement of ethanol production.

  12. Technology Deployment Case Studies

    Broader source: Energy.gov [DOE]

    Find technology deployment case studies below. Click on each individual project link to see the full case study. You can also view a map of technology deployment case studies.

  13. Spark ignited turbulent flame kernel growth. Annual report, January--December, 1992

    SciTech Connect (OSTI)

    Santavicca, D.A.

    1994-06-01

    Cyclic combustion variations in spark-ignition engines limit the use of dilute charge strategies for achieving low NO{sub x} emissions and improved fuel economy. Results from an experimental study of the effect of incomplete fuel-air mixing (ifam) on spark-ignited flame kernel growth in turbulent propane-air mixtures are presented. The experiments were conducted in a turbulent flow system that allows for independent variation of flow parameters, ignition system parameters, and the degree of fuel-air mixing. Measurements were made at 1 atm and 300 K conditions. Five cases were studied; a premixed and four incompletely mixed cases with 6%, 13%, 24% and 33% RMS (root-mean-square) fluctuations in the fuel/air equivalence ratio. High speed laser shadowgraphy at 4,000 frames-per-second was used to record flame kernel growth following spark ignition, from which the equivalent flame kernel radius as a function of time was determined. The effect of ifam was evaluated in terms of the flame kernel growth rate, cyclic variations in the flame kernel growth, and the rate of misfire. The results show that fluctuations in local mixture strength due to ifam cause the flame kernel surface to become wrinkled and distorted; and that the amount of wrinkling increases as the degree of ifam. Ifam was also found to result in a significant increase in cyclic variations in the flame kernel growth. The average flame kernel growth rates for the premixed and the incompletely mixed cases were found to be within the experimental uncertainty except for the 33%-RMS-fluctuation case where the growth rate is significantly lower. The premixed and 6%-RMS-fluctuation cases had a 0% misfire rate. The misfire rates were 1% and 2% for the 13%-RMS-fluctuation and 24%-RMS-fluctuation cases, respectively; however, it drastically increased to 23% in the 33%-RMS-fluctuation case.

  14. Chapter 9: Enabling Capabilities for Science and Energy | A Comparison of Research Funding Modalities

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Funding Modalities High-Performance Computing Capabilities and Allocations User Facility Statistics Examples and Case Studies ENERGY U.S. DEPARTMENT OF Quadrennial Technology Review 2015 1 Quadrennial Technology Review 2015 A Comparison of Research Center Funding Modalities Chapter 9: Enabling Capabilities for Science and Energy A Comparison of Multi-disciplinary, Multi-scale Research Center Funding Modalities Three Department of Energy (DOE) research center modalities-the Energy Frontier

  15. Rate Case Elements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Proceeding Rate Information Residential Exchange Program Surplus Power Sales Reports Rate Case Elements BPA's rate cases are decided "on the record." That is, in making a decision...

  16. BP-12 Rate Case

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Skip navigation links Financial Information Financial Public Processes Asset Management Cost Verification Process Rate Cases BP-18 Rate Case Related Publications Meetings...

  17. BP-16 Rate Case

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Skip navigation links Financial Information Financial Public Processes Asset Management Cost Verification Process Rate Cases BP-18 Rate Case Related Publications Meetings...

  18. Before a Rate Case

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    links Financial Information Financial Public Processes Asset Management Cost Verification Process Rate Cases BP-18 Rate Case Related Publications Meetings and Workshops Customer...

  19. OSCARS Case Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    OSCARS & JGI Science DMZ Case Studies Multi-facility Workflow Case Study News & Publications ESnet News Publications and Presentations Galleries ESnet Awards and Honors Blog ESnet...

  20. WARP Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WARP Case Study WARP Case Study Background WARP is an accelerator code that is used to conduct detailed simulations of particle accelerators, among other high energy physics...

  1. Fatigue crack growth behavior of Al-Li alloy 1441

    SciTech Connect (OSTI)

    Prakash, R.V.; Parida, B.K.

    1995-12-31

    Fatigue crack growth behavior of Al-Li alloy 1441 having a marginally lower lithium content, compared to 80xx and 20xx series Al-Li alloys is presented in this paper. This investigation was conducted on single edge tension--SE(T)--specimens, under constant amplitude as well as under MiniLCA flight spectrum loading with the specific objective of determining the effects of stress ratio, orientation, thickness and cladding. Three thicknesses were considered: 1.2 mm(clad and unclad), 2.0 mm(clad and unclad) and 8.0 mm unclad. Constant amplitude fatigue tests were conducted at stress ratios of {minus}0.3, 0.1 and 0.7. Testing was performed under ambient conditions and along three orientations, namely L-T, T-L and L+45 degrees. Crack growth characteristics of this alloy are compared with that of BS:L73 (2014-T4 equivalent) for assessing the possibility of replacing BS:L73. Significant effect of stress ratio on crack growth rate was observed in all thicknesses. However, in case of 1.2 and 2.0 mm thick sheets, the effect was minimal at intermediate-crack growth regime. The orientation of the specimen does not adversely affect the fatigue crack growth behavior of 8.0 mm and 2.0 mm thick specimens. However, for 1.2 mm unclad sheet crack growth resistance in L-T direction was found to be superior to that along T-L direction. In majority of test cases considered, no significant effect was observed on crack growth rate due to thickness or cladding. Crack growth characteristics of Al-Li alloy 1441 and Al-Cu alloy BS:L73 under constant amplitude as well as MiniLCA spectrum loading are similar in the low and intermediate-crack growth rate regime. Based on these observations, it is felt that this Al-Li alloy has the potential for future aerospace applications.

  2. Distributed Wind Policy Comparison Tool Guidebook

    SciTech Connect (OSTI)

    Not Available

    2011-11-01

    Power through Policy: 'Best Practices' for Cost-Effective Distributed Wind is a U.S. Department of Energy (DOE)-funded project to identify distributed wind technology policy best practices and to help policymakers, utilities, advocates, and consumers examine their effectiveness using a pro forma model. Incorporating a customized feed from the Database of State Incentives for Renewables and Efficiency (DSIRE), the Web-based Distributed Wind Policy Comparison Tool (Policy Tool) is designed to assist state, local, and utility officials in understanding the financial impacts of different policy options to help reduce the cost of distributed wind technologies. The Policy Tool can be used to evaluate the ways that a variety of federal and state policies and incentives impact the economics of distributed wind (and subsequently its expected market growth). It also allows policymakers to determine the impact of policy options, addressing market challenges identified in the U.S. DOE's '20% Wind Energy by 2030' report and helping to meet COE targets.

  3. Digital electronic bone growth stimulator

    DOE Patents [OSTI]

    Kronberg, J.W.

    1995-05-09

    A device is described for stimulating bone tissue by applying a low level alternating current signal directly to the patient`s skin. A crystal oscillator, a binary divider chain and digital logic gates are used to generate the desired waveforms that reproduce the natural electrical characteristics found in bone tissue needed for stimulating bone growth and treating osteoporosis. The device, powered by a battery, contains a switch allowing selection of the correct waveform for bone growth stimulation or osteoporosis treatment so that, when attached to the skin of the patient using standard skin contact electrodes, the correct signal is communicated to the underlying bone structures. 5 figs.

  4. Digital electronic bone growth stimulator

    DOE Patents [OSTI]

    Kronberg, James W.

    1995-01-01

    A device for stimulating bone tissue by applying a low level alternating current signal directly to the patient's skin. A crystal oscillator, a binary divider chain and digital logic gates are used to generate the desired waveforms that reproduce the natural electrical characteristics found in bone tissue needed for stimulating bone growth and treating osteoporosis. The device, powered by a battery, contains a switch allowing selection of the correct waveform for bone growth stimulation or osteoporosis treatment so that, when attached to the skin of the patient using standard skin contact electrodes, the correct signal is communicated to the underlying bone structures.

  5. Nonlinear structural crack growth monitoring

    DOE Patents [OSTI]

    Welch, Donald E. (Oak Ridge, TN); Hively, Lee M. (Philadelphia, TN); Holdaway, Ray F. (Clinton, TN)

    2002-01-01

    A method and apparatus are provided for the detection, through nonlinear manipulation of data, of an indicator of imminent failure due to crack growth in structural elements. The method is a process of determining energy consumption due to crack growth and correlating the energy consumption with physical phenomena indicative of a failure event. The apparatus includes sensors for sensing physical data factors, processors or the like for computing a relationship between the physical data factors and phenomena indicative of the failure event, and apparatus for providing notification of the characteristics and extent of such phenomena.

  6. Fostering Growth | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Soft Costs » Fostering Growth Fostering Growth The solar energy industry in the United States is growing rapidly as the price of solar panels has decreased over the past decade. U.S. solar installations doubled from 2009 to 2010, and the domestic market was worth $6 billion in 2010. Despite this upward trend, solar energy is only 1% of the current U.S. electricity supply. The SunShot Vision Study says that cost-competitive solar has an estimated potential to supply roughly 14% of domestic

  7. A continuum-scale model of hydrogen precipitate growth in tungsten plasma-facing materials.

    SciTech Connect (OSTI)

    Causey, Rion A.; Cowgill, Donald F.; Kolasinski, Robert D.

    2010-05-01

    The low solubility of hydrogen in tungsten leads to the growth of near-surface hydrogen precipitates during high-flux plasma exposure, strongly affecting migration and trapping in the material. We have developed a continuum-scale model of precipitate growth that leverages existing techniques for simulating the evolution of {sup 3}He gas bubbles in metal tritides. The present approach focuses on bubble growth by dislocation loop punching, assuming a diffusing flux to nucleation sites that arises from ion implantation. The bubble size is dictated by internal hydrogen pressure, the mechanical properties of the material, as well as local stresses. In this article, we investigate the conditions required for bubble growth. Recent focused ion beam (FIB) profiling studies that reveal the sub-surface damage structure provide an experimental database for comparison with the modeling results.

  8. A pathway for the growth of core-shell Pt-Pd nanoparticles

    SciTech Connect (OSTI)

    Narula, Chaitanya Kumar; Yang, Xiaofan; Li, Chen; Pennycook, Stephen J; Lupini, Andrew R

    2015-10-12

    In this study, the aging of both Pt-Pd nanoparticles and core-shell Pt-Pd nanoparticles has been reported to result in alloying of Pt with Pd. In comparison to monometallic Pt catalysts, the growth of Pd-Pt bimetallics is slower; however, the mechanism of growth of particles and the mechanism by which Pd improves the hydrothermal durability of bimetallic Pd-Pt particles remains uncertain. In our work on hydrothermal aging of core-shell Pt-Pd nanoparticles, synthesized by solution methods, with varying Pd:Pt ratio of 1:4, 1:1, and 4:1, we compare the growth of core-shell Pt-Pd nanoparticles and find that particles grow by migrating and joining together. The unique feature of the observed growth is that Pd shells from both particles open up and join, allowing the cores to merge. At high temperatures, alloying occurs in good agreement with reports by other workers.

  9. Direct flow crystal growth system

    DOE Patents [OSTI]

    Montgomery, Kenneth E. (Tracy, CA); Milanovich, Fred P. (Lafayette, CA)

    1992-01-01

    A crystal is grown in a constantly filtered solution which is flowed directly into the growing face of a crystal. In a continuous flow system, solution at its saturation temperature is removed from a crystal growth tank, heated above its saturation temperature, filtered, cooled back to its saturation temperature, and returned to the tank.

  10. 2015 NREL Industry Growth Forum

    Broader source: Energy.gov [DOE]

    During NREL’s 2015 Industry Growth Forum, 30 competitively selected clean energy startups will pitch their businesses to investors and compete to win the NREL Best Venture Award.  One of the...

  11. SBA Growth Accelerator Fund Competition

    Broader source: Energy.gov [DOE]

    The U.S. Small Business Administration (SBA) is accepting applications for the Growth Accelerator Fund Competition to identify the nation's innovative accelerators and similar organizations and award them cash prizes they may use to fund their operations costs and allow them to bring startup competitions to scale and new ideas to life.

  12. DOE's Public Database for Green Building Case Studies: Preprint

    SciTech Connect (OSTI)

    Torcellini, P. A.; Crawley, D. B.

    2003-11-01

    To help capture valuable information on''green building'' case studies, the U.S. Department of Energy has created an online database for collecting, standardizing, and disseminating information about high-performance, green projects. Type of information collected includes green features, design processes, energy performance, and comparison to other high-performance, green buildings.

  13. Comparison between two Lysholm engines

    SciTech Connect (OSTI)

    Frau, B.A.

    1983-01-01

    The University of California at Berkeley (UCB) and the Jet Propulsion Laboratory (JPL) both have been working on the Lysholm engine as an expander of two phase geothermal brine. The sizes of the machines, (The machine at UCB is rated at 25 kW, and the machine that JPL tested is rated at 1MW) as well as the approaches, are different. Here, some comparisons are made in order to clarify the direction in which future efforts should be conducted.

  14. Method for crystal growth control

    DOE Patents [OSTI]

    Yates, Douglas A. (Burlington, MA); Hatch, Arthur E. (Waltham, MA); Goldsmith, Jeff M. (Medford, MA)

    1981-01-01

    The growth of a crystalline body of a selected material is controlled so that the body has a selected cross-sectional shape. The apparatus is of the type which includes the structure normally employed in known capillary die devices as well as means for observing at least the portion of the surfaces of the growing crystalline body and the meniscus (of melt material from which the body is being pulled) including the solid/liquid/vapor junction in a direction substantially perpendicular to the meniscus surface formed at the junction when the growth of the crystalline body is under steady state conditions. The cross-sectional size of the growing crystalline body can be controlled by determining which points exhibit a sharp change in the amount of reflected radiation of a preselected wavelength and controlling the speed at which the body is being pulled or the temperature of the growth pool of melt so as to maintain those points exhibiting a sharp change at a preselected spatial position relative to a predetermined reference position. The improvement comprises reference object means positioned near the solid/liquid/vapor junction and capable of being observed by the means for observing so as to define said reference position so that the problems associated with convection current jitter are overcome.

  15. Science DMZ Case Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Science DMZ Case Studies Science DMZ @ UF Science DMZ @ CU Science DMZ @ Penn & VTTI Science DMZ @ NOAA Science DMZ @ NERSC Science DMZ @ ALS Multi-facility Workflow Case Study...

  16. Comparison

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    these response statistics for data collected from either physical experimentation or numerical modeling. Here, we consider the application of a series of such methods to...

  17. Comparison

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    chord although this will later be shown to be un- a Electronic mail: jcreardon@wisc.edu REVIEW OF SCIENTIFIC INSTRUMENTS VOLUME 74, NUMBER 3 MARCH 2003 1892 0034-6748...

  18. Method and apparatus for aluminum nitride monocrystal boule growth

    DOE Patents [OSTI]

    Wang, Shaoping (Brookfield, CT)

    2009-04-28

    A crystal growth setup within a physical vapor transport growth furnace system for producing AlN monocrystal boules at high temperatures includes a crucible effective to contain an AlN source material and a growing AlN crystal boule. This crucible has a thin wall thickness in at least that portion housing the growing AlN crystal boule. Other components include a susceptor, in case of an inductive heating, or a heater, in case of a resistive heating, a thermal insulation enclosing the susceptor or heater effective to provide a thermal gradient inside the crucible in the range of 5-100.degree. C./cm and a furnace chamber capable of being operated from a vacuum (<0.1 torr) to a gas pressure of at least 4000 torr through filling or flowing a nitrogen gas or a mixture of nitrogen gas and argon gas. The high temperatures contribute to a high boule growth rate and the thin wall thickness contributes to reduced imparted stress during boule removal.

  19. Comparison of Home Retrofit Programs in Wisconsin

    SciTech Connect (OSTI)

    Cunningham, Kerrie; Hannigan, Eileen

    2013-03-01

    To explore ways to reduce customer barriers and increase home retrofit completions, several different existing home retrofit models have been implemented in the state of Wisconsin. This study compared these programs' performance in terms of savings per home and program cost per home to assess the relative cost-effectiveness of each program design. However, given the many variations in these different programs, it is difficult to establish a fair comparison based on only a small number of metrics. Therefore, the overall purpose of the study is to document these programs' performance in a case study approach to look at general patterns of these metrics and other variables within the context of each program. This information can be used by energy efficiency program administrators and implementers to inform home retrofit program design. Six different program designs offered in Wisconsin for single-family energy efficiency improvements were included in the study. For each program, the research team provided information about the programs' approach and goals, characteristics, achievements and performance. The program models were then compared with performance results-program cost and energy savings-to help understand the overall strengths and weaknesses or challenges of each model.

  20. Comparison of Home Retrofit Programs in Wisconsin

    SciTech Connect (OSTI)

    Cunningham, K.; Hannigan, E.

    2013-03-01

    To explore ways to reduce customer barriers and increase home retrofit completions, several different existing home retrofit models have been implemented in the state of Wisconsin. This study compared these programs' performance in terms of savings per home and program cost per home to assess the relative cost-effectiveness of each program design. However, given the many variations in these different programs, it is difficult to establish a fair comparison based on only a small number of metrics. Therefore, the overall purpose of the study is to document these programs' performance in a case study approach to look at general patterns of these metrics and other variables within the context of each program. This information can be used by energy efficiency program administrators and implementers to inform home retrofit program design. Six different program designs offered in Wisconsin for single-family energy efficiency improvements were included in the study. For each program, the research team provided information about the programs' approach and goals, characteristics, achievements and performance. The program models were then compared with performance results -- program cost and energy savings -- to help understand the overall strengths and weaknesses or challenges of each model.

  1. WCI Case for Coal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    energy is needed for economic growth and poverty alleviation. * All energy sources will be ... The World Bank on the role of energy in poverty alleviation "Reliable energy is a key ...

  2. New Partners for Smart Growth Conference

    Broader source: Energy.gov [DOE]

    The New Partners for Smart Growth Conference is the nation's largest smart growth and sustainability conference. The three-day conference is themed, "Practical Tools and Innovative Strategies for Creating Great Communities."

  3. The Compelling Case for Natural Gas Vehicles | Department of Energy

    Energy Savers [EERE]

    The Compelling Case for Natural Gas Vehicles The Compelling Case for Natural Gas Vehicles Presentation-given at the April 2012 Federal Utility Partnership Working Group (FUPWG) meeting-covers the natural gas vehicle (NGV) market, the benefits of NGVs, the growing selection of NGVs, and more. PDF icon fupwg_spring12_yborra.pdf More Documents & Publications QER - Comment of American Gas Association 3 Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure Development asdfadfa

  4. Modeling delamination growth in composites

    SciTech Connect (OSTI)

    Reedy, E.D. Jr.; Mello, F.J.

    1996-12-01

    A method for modeling the initiation and growth of discrete delaminations in shell-like composite structures is presented. The laminate is divided into two or more sublaminates, with each sublaminate modeled with four-noded quadrilateral shell elements. A special, eight-noded hex constraint element connects opposing sublaminate shell elements. It supplies the nodal forces and moments needed to make the two opposing shell elements act as a single shell element until a prescribed failure criterion is satisfied. Once the failure criterion is attained, the connection is broken, creating or growing a discrete delamination. This approach has been implemented in a 3D finite element code. This code uses explicit time integration, and can analyze shell-like structures subjected to large deformations and complex contact conditions. The shell elements can use existing composite material models that include in-plane laminate failure modes. This analysis capability was developed to perform crashworthiness studies of composite structures, and is useful whenever there is a need to estimate peak loads, energy absorption, or the final shape of a highly deformed composite structure. This paper describes the eight-noded hex constraint element used to model the initiation and growth of a delamination, and discusses associated implementation issues. Particular attention is focused on the delamination growth criterion, and it is verified that calculated results do not depend on element size. In addition, results for double cantilever beam and end notched flexure specimens are presented and compared to measured data to assess the ability of the present approach to model a growing delamination.

  5. Plenum type crystal growth process

    DOE Patents [OSTI]

    Montgomery, Kenneth E. (Tracy, CA)

    1992-01-01

    Crystals are grown in a tank which is divided by a baffle into a crystal growth region above the baffle and a plenum region below the baffle. A turbine blade or stirring wheel is positioned in a turbine tube which extends through the baffle to generate a flow of solution from the crystal growing region to the plenum region. The solution is pressurized as it flows into the plenum region. The pressurized solution flows back to the crystal growing region through return flow tubes extending through the baffle. Growing crystals are positioned near the ends of the return flow tubes to receive a direct flow of solution.

  6. Apparatus for monitoring crystal growth

    DOE Patents [OSTI]

    Sachs, Emanual M. (Watertown, MA)

    1981-01-01

    A system and method are disclosed for monitoring the growth of a crystalline body from a liquid meniscus in a furnace. The system provides an improved human/machine interface so as to reduce operator stress, strain and fatigue while improving the conditions for observation and control of the growing process. The system comprises suitable optics for forming an image of the meniscus and body wherein the image is anamorphic so that the entire meniscus can be viewed with good resolution in both the width and height dimensions. The system also comprises a video display for displaying the anamorphic image. The video display includes means for enhancing the contrast between any two contrasting points in the image. The video display also comprises a signal averager for averaging the intensity of at least one preselected portions of the image. The value of the average intensity, can in turn be utilized to control the growth of the body. The system and method are also capable of observing and monitoring multiple processes.

  7. Method of monitoring crystal growth

    DOE Patents [OSTI]

    Sachs, Emanual M. (Watertown, MA)

    1982-01-01

    A system and method are disclosed for monitoring the growth of a crystalline body from a liquid meniscus in a furnace. The system provides an improved human/machine interface so as to reduce operator stress, strain and fatigue while improving the conditions for observation and control of the growing process. The system comprises suitable optics for forming an image of the meniscus and body wherein the image is anamorphic so that the entire meniscus can be viewed with good resolution in both the width and height dimensions. The system also comprises a video display for displaying the anamorphic image. The video display includes means for enhancing the contrast between any two contrasting points in the image. The video display also comprises a signal averager for averaging the intensity of at least one preselected portions of the image. The value of the average intensity, can in turn be utilized to control the growth of the body. The system and method are also capable of observing and monitoring multiple processes.

  8. EMGeo Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EMGeo Case Study EMGeo Case Study Background EMGeo is composed of two geophysical imaging applications: one for subsurface imaging using electromagnetic data and another using seismic data. Although the applications model different physics (Maxwell's equations in one case, the elastic wave equation in another) they have much in common. First, both are structured similarly, taking advantage of high-level data parallelism to solve many semi-independent sub-problems concurrently, yielding excellent

  9. Application Case Studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Studies Application Case Studies Early work with NESAP Staff at NERSC as well as Cray and Intel Engineers have lead to a number of application case studies. Early application case studies The Babbage test system was used to study representative applications and kernels in various scientific fields to gain experience with the challenges and strategies needed to optimize code performance on the MIC architecture. Below we highlight a few examples: BerkeleyGW The BerkeleyGW package is a materials

  10. Case Study FAQ

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Requirements Reviews: Target 2017 Requirements Reviews: Target 2014 Overview Published Reports Case Study FAQs NERSC HPC Achievement Awards Share Your Research User Submitted Research Citations NERSC Citations Home » Science at NERSC » HPC Requirements Reviews » Case Study FAQs Case Study FAQ General Questions What is NERSC? NERSC is the National Energy Research Scientific Computing Center, the high-end scientific computing facility for the Department of Energy's Office of Science. NERSC

  11. Korea's Green Growth Strategy: Mitigating Climate Change and...

    Open Energy Info (EERE)

    Korea's Green Growth Strategy: Mitigating Climate Change and Developing New Growth Engines Jump to: navigation, search Name Korea's Green Growth Strategy: Mitigating Climate Change...

  12. OSCARS Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The Network OSCARS How It Works Who's Using OSCARS? OSCARS and Future Tech OSCARS Standard and Open Grid Forum OSCARS Developers Community Read More... OSCARS Case Study...

  13. Appendix A: Reference case

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Reference case Energy Information Administration Annual Energy Outlook 2014 Table A17. Renewable energy consumption by sector and source (quadrillion Btu) Sector and source...

  14. Appendix A: Reference case

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    4 Reference case Table A2. Energy consumption by sector and source (quadrillion Btu per year, unless otherwise noted) Energy Information Administration Annual Energy Outlook 2014...

  15. Comparisons of Independent Petroleum Supply Statistics

    Reports and Publications (EIA)

    2005-01-01

    Compares final petroleum data published in the Petroleum Supply Annual with similar petroleum data obtained from other sources. Data comparisons are presented for 1994 through 2003.

  16. Controlled growth of semiconductor crystals

    DOE Patents [OSTI]

    Bourret-Courchesne, E.D.

    1992-07-21

    A method is disclosed for growth of III-V, II-VI and related semiconductor single crystals that suppresses random nucleation and sticking of the semiconductor melt at the crucible walls. Small pieces of an oxide of boron B[sub x]O[sub y] are dispersed throughout the comminuted solid semiconductor charge in the crucible, with the oxide of boron preferably having water content of at least 600 ppm. The crucible temperature is first raised to a temperature greater than the melt temperature T[sub m1] of the oxide of boron (T[sub m1]=723 K for boron oxide B[sub 2]O[sub 3]), and the oxide of boron is allowed to melt and form a reasonably uniform liquid layer between the crucible walls and bottom surfaces and the still-solid semiconductor charge. The temperature is then raised to approximately the melt temperature T[sub m2] of the semiconductor charge material, and crystal growth proceeds by a liquid encapsulated, vertical gradient freeze process. About half of the crystals grown have a dislocation density of less than 1000/cm[sup 2]. If the oxide of boron has water content less than 600 ppm, the crucible material should include boron nitride, a layer of the inner surface of the crucible should be oxidized before the oxide of boron in the crucible charge is melted, and the sum of thicknesses of the solid boron oxide layer and liquid boron oxide layer should be at least 50 [mu]m. 7 figs.

  17. Controlled growth of semiconductor crystals

    DOE Patents [OSTI]

    Bourret-Courchesne, Edith D. (Richmond, CA)

    1992-01-01

    A method for growth of III-V, II-VI and related semiconductor single crystals that suppresses random nucleation and sticking of the semiconductor melt at the crucible walls. Small pieces of an oxide of boron B.sub.x O.sub.y are dispersed throughout the comminuted solid semiconductor charge in the crucible, with the oxide of boron preferably having water content of at least 600 ppm. The crucible temperature is first raised to a temperature greater than the melt temperature T.sub.m1 of the oxide of boron (T.sub.m1 =723.degree. K. for boron oxide B.sub.2 O.sub.3), and the oxide of boron is allowed to melt and form a reasonably uniform liquid layer between the crucible walls and bottom surfaces and the still-solid semiconductor charge. The temperature is then raised to approximately the melt temperature T.sub.m2 of the semiconductor charge material, and crystal growth proceeds by a liquid encapsulated, vertical gradient freeze process. About half of the crystals grown have a dislocation density of less than 1000/cm.sup.2. If the oxide of boron has water content less than 600 ppm, the crucible material should include boron nitride, a layer of the inner surface of the crucible should be oxidized before the oxide of boron in the crucible charge is melted, and the sum of thicknesses of the solid boron oxide layer and liquid boron oxide layer should be at least 50 .mu.m.

  18. Synthetic heparin-binding growth factor analogs

    DOE Patents [OSTI]

    Pena, Louis A.; Zamora, Paul; Lin, Xinhua; Glass, John D.

    2007-01-23

    The invention provides synthetic heparin-binding growth factor analogs having at least one peptide chain that binds a heparin-binding growth factor receptor, covalently bound to a hydrophobic linker, which is in turn covalently bound to a non-signaling peptide that includes a heparin-binding domain. The synthetic heparin-binding growth factor analogs are useful as soluble biologics or as surface coatings for medical devices.

  19. ARM - Lesson Plans: Rate of Coral Growth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rate of Coral Growth Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About ARM Global Warming FAQ Just for Fun Meet our Friends Cool Sites Teachers Teachers' Toolbox Lesson Plans Lesson Plans: Rate of Coral Growth Objective The objective is to understand the fact that the growth of coral depends on water depth and the effect of sea level changes on corals. Materials Each student or group of students

  20. The growth of structure in interacting dark energy models

    SciTech Connect (OSTI)

    Caldera-Cabral, Gabriela; Maartens, Roy; Schaefer, Bjoern Malte E-mail: roy.maartens@port.ac.uk

    2009-07-01

    If dark energy interacts with dark matter, there is a change in the background evolution of the universe, since the dark matter density no longer evolves as a{sup ?3}. In addition, the non-gravitational interaction affects the growth of structure. In principle, these changes allow us to detect and constrain an interaction in the dark sector. Here we investigate the growth factor and the weak lensing signal for a new class of interacting dark energy models. In these models, the interaction generalises the simple cases where one dark fluid decays into the other. In order to calculate the effect on structure formation, we perform a careful analysis of the perturbed interaction and its effect on peculiar velocities. Assuming a normalization to today's values of dark matter density and overdensity, the signal of the interaction is an enhancement (suppression) of both the growth factor and the lensing power, when the energy transfer in the background is from dark matter to dark energy (dark energy to dark matter)

  1. Secondary heat exchanger design and comparison for advanced high temperature reactor

    SciTech Connect (OSTI)

    Sabharwall, P.; Kim, E. S.; Siahpush, A.; McKellar, M.; Patterson, M.

    2012-07-01

    Next generation nuclear reactors such as the advanced high temperature reactor (AHTR) are designed to increase energy efficiency in the production of electricity and provide high temperature heat for industrial processes. The efficient transfer of energy for industrial applications depends on the ability to incorporate effective heat exchangers between the nuclear heat transport system and the industrial process heat transport system. This study considers two different types of heat exchangers - helical coiled heat exchanger and printed circuit heat exchanger - as possible options for the AHTR secondary heat exchangers with distributed load analysis and comparison. Comparison is provided for all different cases along with challenges and recommendations. (authors)

  2. VP 100: Growth in solar means growth in Ohio | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Growth in solar means growth in Ohio VP 100: Growth in solar means growth in Ohio October 6, 2010 - 10:57am Addthis DuPont is betting on major growth in the market for solar energy -- and therefore for its Tedlar film, a durable backing for silicon solar panels. | Photo Courtesy of DuPont DuPont is betting on major growth in the market for solar energy -- and therefore for its Tedlar film, a durable backing for silicon solar panels. | Photo Courtesy of DuPont Lorelei Laird Writer, Energy

  3. "Conflict Between Economic Growth and Environmental Protection...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9, 2012, 4:15pm Colloquia MBG Auditorium "Conflict Between Economic Growth and Environmental Protection", Dr. Bryan Czech, resident, Center for the Advancement of the Steady State...

  4. GROWTH AND ELECTROCHEMICAL CHARACTERIZATION OF CARBON NANOSPIKE...

    Office of Scientific and Technical Information (OSTI)

    Title: GROWTH AND ELECTROCHEMICAL CHARACTERIZATION OF CARBON NANOSPIKE THIN FILM ELECTRODES Authors: Sheridan, Leah B 1 ; Hensley, Dale K 1 ; Lavrik, Nickolay V 1 ; Smith, ...

  5. Sandia Energy - Biomimetic Approach to Nanoparticle Growth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    biological growth, a new 'Extended LaMer' method for reproducible and predictable synthesis of nanoparticles was developed. Significance and Impact This general approach allows...

  6. Digital electronic bone growth stimulator

    DOE Patents [OSTI]

    Kronberg, J.W.

    1993-01-01

    The present invention relates to the electrical treatment of biological tissue. In particular, the present invention discloses a device that produces discrete electrical pulse trains for treating osteoporosis and accelerating bone growth. According to its major aspects and broadly stated, the present invention consists of an electrical circuit configuration capable of generating Bassett-type waveforms shown with alternative signals provide for the treatment of either fractured bones or osteoporosis. The signal generator comprises a quartz clock, an oscillator circuit, a binary divider chain, and a plurality of simple, digital logic gates. Signals are delivered efficiently, with little or no distortion, and uniformly distributed throughout the area of injury. Perferably, power is furnished by widely available and inexpensive radio batteries, needing replacement only once in several days. The present invention can be affixed to a medical cast without a great increase in either weight or bulk. Also, the disclosed stimulator can be used to treat osteoporosis or to strengthen a healing bone after the cast has been removed by attaching the device to the patient`s skin or clothing.

  7. EMGeo Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    methods (QMR in one case, and IDR in the other), both solvers are dominated by memory bandwidth intensive operations like sparse matrix-vector multiply (SpMV), dot...

  8. Attractor comparisons based on density

    SciTech Connect (OSTI)

    Carroll, T. L.

    2015-01-15

    Recognizing a chaotic attractor can be seen as a problem in pattern recognition. Some feature vector must be extracted from the attractor and used to compare to other attractors. The field of machine learning has many methods for extracting feature vectors, including clustering methods, decision trees, support vector machines, and many others. In this work, feature vectors are created by representing the attractor as a density in phase space and creating polynomials based on this density. Density is useful in itself because it is a one dimensional function of phase space position, but representing an attractor as a density is also a way to reduce the size of a large data set before analyzing it with graph theory methods, which can be computationally intensive. The density computation in this paper is also fast to execute. In this paper, as a demonstration of the usefulness of density, the density is used directly to construct phase space polynomials for comparing attractors. Comparisons between attractors could be useful for tracking changes in an experiment when the underlying equations are too complicated for vector field modeling.

  9. RTU Comparison Calculator Enhancement Plan

    SciTech Connect (OSTI)

    Miller, James D.; Wang, Weimin; Katipamula, Srinivas

    2014-03-31

    Over the past two years, Department of Energys Building Technologies Office (BTO) has been investigating ways to increase the operating efficiency of the packaged rooftop units (RTUs) in the field. First, by issuing a challenge to the RTU manufactures to increase the integrated energy efficiency ratio (IEER) by 60% over the existing ASHRAE 90.1-2010 standard. Second, by evaluating the performance of an advanced RTU controller that reduces the energy consumption by over 40%. BTO has previously also funded development of a RTU comparison calculator (RTUCC). RTUCC is a web-based tool that provides the user a way to compare energy and cost savings for two units with different efficiencies. However, the RTUCC currently cannot compare savings associated with either the RTU Challenge unit or the advanced RTU controls retrofit. Therefore, BTO has asked PNNL to enhance the tool so building owners can compare energy and savings associated with this new class of products. This document provides the details of the enhancements that are required to support estimating energy savings from use of RTU challenge units or advanced controls on existing RTUs.

  10. RTU Comparison Calculator Enhancement Plan

    SciTech Connect (OSTI)

    Miller, James D.; Wang, Weimin; Katipamula, Srinivas

    2015-07-01

    Over the past two years, Department of Energy’s Building Technologies Office (BTO) has been investigating ways to increase the operating efficiency of the packaged rooftop units (RTUs) in the field. First, by issuing a challenge to the RTU manufactures to increase the integrated energy efficiency ratio (IEER) by 60% over the existing ASHRAE 90.1-2010 standard. Second, by evaluating the performance of an advanced RTU controller that reduces the energy consumption by over 40%. BTO has previously also funded development of a RTU comparison calculator (RTUCC). RTUCC is a web-based tool that provides the user a way to compare energy and cost savings for two units with different efficiencies. However, the RTUCC currently cannot compare savings associated with either the RTU Challenge unit or the advanced RTU controls retrofit. Therefore, BTO has asked PNNL to enhance the tool so building owners can compare energy and savings associated with this new class of products. This document provides the details of the enhancements that are required to support estimating energy savings from use of RTU challenge units or advanced controls on existing RTUs.

  11. VASP Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    VASP Case Study VASP Case Study Code description and computational problem The Vienna Ab-initio Simulation Package (VASP) [1-2] is a widely used materials science application for performing ab-initio electronic structure calculations and quantum-mechanical molecular dynamics (MD) simulations using pseudopotentials or the projector-augmented wave method and a plane wave basis set. VASP computes an approximate solution to the many-body Schrödinger equation, either within the Density Functional

  12. WARP Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    WARP Case Study WARP Case Study Background WARP is an accelerator code that is used to conduct detailed simulations of particle accelerators, among other high energy physics applications. It is a so-called Particle-In-Cell (PIC) code that solves for the motion of charged particles acted upon by electric and magnetic forces. The particle motion is computed in a Lagrangian sense, following individual particles. The electric and magnetic fields acting on the particle are considered to be Eulerian

  13. Early application case studies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Early application case studies Early application case studies The Babbage test system was used to study representative applications and kernels in various scientific fields to gain experience with the challenges and strategies needed to optimize code performance on the MIC architecture. Below we highlight a few examples: BerkeleyGW The BerkeleyGW package is a materials science application that calculates electronic and optical properties with quantitative accuracy, a critical need in materials

  14. Better Buildings Case Competition

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Better Buildings Case Competition 2014 Building Technologies Office Peer Review Elena Alschuler, Elena.Alschuler@ee.Doe.Gov Department of Energy Project Summary Timeline: Start date: 2012 Planned end date: Annual event Key Milestones 9/23/13 - Student Team Registration Opened 11/11/13- Cases distributed 2/17/13 - Solution proposals due 3/14/14 - Solution proposals presented at US DOE, winners selected by industry and expert judges April 2014 - solutions posted Budget: Total DOE $ to date:

  15. Single casing reheat turbine

    SciTech Connect (OSTI)

    Matsushima, Tatsuro; Nishimura, Shigeo

    1999-07-01

    For conventional power plants, regenerative reheat steam turbines have been accepted as the most practical method to meet the demand for efficient and economical power generation. Recently the application of reheat steam turbines for combined cycle power plant began according to the development of large-capacity high temperature gas turbine. The two casing double flow turbine has been applied for this size of reheat steam turbine. The single casing reheat turbine can offer economical and compact power plant. Through development of HP-LP combined rotor and long LP blading series, Mitsubishi Heavy Industries, Ltd. had developed a single casing reheat steam turbine series and began to use it in actual plants. Six units are already in operation and another seven units are under manufacturing. Multiple benefits of single casing reheat turbine are smaller space requirements, shorter construction and erection period, equally good performance, easier operation and maintenance, shorter overhaul period, smaller initial investment, lower transportation expense and so on. Furthermore, single exhaust steam turbine makes possible to apply axial exhaust type, which will lower the height of T/G foundation and T/G housing. The single casing reheat turbine has not only compact and economical configuration itself but also it can reduce the cost of civil construction. In this paper, major developments and design features of the single casing reheat turbine are briefly discussed and operating experience, line-up and technical consideration for performance improvement are presented.

  16. Case studies on recent fossil-fired plants

    SciTech Connect (OSTI)

    Henderson, C.

    2007-12-31

    The article summarises the findings of case studies on fossil-fired power plants carried out by the IEA Clean Coal Centre for the IEA at the request of world leaders at the Gleneagles G8 Summit in July 2005. The studies compared the cost, efficiency and emissions of eight recently constructed coal-fired plants using pulverized coal combustion with subcritical, supercritical or ultra-supercritical steam turbine cycles. Also included was a review of IGCC developments. A case study of a natural gas combined-cycle plant was included for comparison. The full report has been published by the IEA. 1 tab.

  17. Torque/Moab vs. SLURM Comparisons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Users » Torque/Moab vs. SLURM Comparisons Torque/Moab vs. SLURM Comparisons TORQUE vs. SLURM Comparison Tables Moab/Torque vs. Slurm Environment Variables Description Moab/Torque Slurm Job Id $PBS_JOBID $SLURM_JOB_ID Job Name $PBS_JOBNAME $SLURM_JOB_NAME Submit Directory $PBS_O_WORKDIR $SLURM_SUBMIT_DIR Node List $PBS_NODEFILE $SLURM_NODELIST Host submitted from $PBS_O_HOST $SLURM_SUBMIT_HOST Nodes allocated $PBS_NUM_NODES $SLURM_JOB_NUM_NODES Number cores/nodes $PBS_NUM_PPN $SLURM_CPUS_ON_NODE

  18. A Case for Climate Neutrality: Case Studies on Moving Towards...

    Open Energy Info (EERE)

    TOOL Name: A Case for Climate Neutrality: Case Studies on Moving Towards a Low Carbon Economy AgencyCompany Organization: United Nations Environment Programme (UNEP) Sector:...

  19. New Report Highlights Growth of America's Clean Energy Job Sector |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean Energy Job Sector August 23, 2012 - 12:20pm Addthis New Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean Energy Job Sector New Report Highlights Growth of America's Clean

  20. Fuel Cell Comparison of Distributed Power Generation Technologies...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Comparison of Distributed Power Generation Technologies Fuel Cell Comparison of Distributed Power Generation Technologies This report examines backup power and prime power systems...

  1. Comparison of methods for geologic storage of carbon dioxide...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Comparison of methods for geologic storage of carbon dioxide in saline formations Citation Details In-Document Search Title: Comparison of methods for geologic...

  2. Comparison of Real World Energy Consumption to Models and DOE...

    Energy Savers [EERE]

    Comparison of Real World Energy Consumption to Models and DOE Test Procedures Comparison of Real World Energy Consumption to Models and DOE Test Procedures This study investigates ...

  3. Particle Measurement Methodology: Comparison of On-road and Lab...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Measurement Methodology: Comparison of On-road and Lab Diesel Particle Size Distributions Particle Measurement Methodology: Comparison of On-road and Lab Diesel Particle Size ...

  4. Comparison of Fuel Cell Technologies: Fact Sheet | Department...

    Broader source: Energy.gov (indexed) [DOE]

    An overview comparison of fuel cell technologies by the Fuel Cell Technologies Office. Comparison of Fuel Cell Technologies More Documents & Publications Hydrogen and Fuel Cell...

  5. Comparison Between Keyhole Weld Model and Laser Welding Experiments...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Comparison Between Keyhole Weld Model and Laser Welding Experiments Citation Details In-Document Search Title: Comparison Between Keyhole Weld Model and Laser...

  6. Comparisons of neutrino event generators from an oscillation...

    Office of Scientific and Technical Information (OSTI)

    of high energy physics data, ideally giving a baseline comparison between the state-of-art theoretical models and experimental data. Presented here is a comparison between three...

  7. Comparison of the Amanzi Model against Analytical Solutions and...

    Office of Scientific and Technical Information (OSTI)

    Comparison of the Amanzi Model against Analytical Solutions and the FEHM Model Citation Details In-Document Search Title: Comparison of the Amanzi Model against Analytical...

  8. Comparison of Uncertainty of Two Precipitation Prediction Models...

    Office of Scientific and Technical Information (OSTI)

    Comparison of Uncertainty of Two Precipitation Prediction Models at Los Alamos National Lab Technical Area 54 Citation Details In-Document Search Title: Comparison of Uncertainty...

  9. Posters Comparisons of Brightness Temperature Measurements and...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    radiometric observations of atmospheric emission and attenuation at 20.6, 31.65, and 90 GHz: A comparison of measurements and theory. IEEE Trans. Antennas Prop. AP-38:1569...

  10. NREL's 23rd Industry Growth Forum Attracts Clean Energy Investors - News

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Releases | NREL NREL's 23rd Industry Growth Forum Attracts Clean Energy Investors Forum to Feature 34 Clean Energy Companies September 23, 2010 Thirty-four clean energy companies will present their business cases to a panel of investors and industry experts in Denver Oct. 19-21 as the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) hosts the 23rd NREL Industry Growth Forum. The 34 companies were selected through an application and review process and will compete for

  11. In Case of Emergency

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    In Case of Emergency In Case of Emergency Print Fire/Police Emergency: ext. 7911 Cell phone or off-site: 510-486-7911 When dialing from off-site, the following numbers need to be proceeded by 486-. the area code for the LBNL is (510). Fire Department (non-emergency): ext. 6015 Police Department (non-emergency): ext. 5472 Non-Emergency Reporting: ext. 6999 Additional information about emergency procedures at Berkeley Lab can be found on the red Emergency Response Guides posted around the lab and

  12. PEROXOTITANATE- AND MONOSODIUM METAL-TITANATE COMPOUNDS AS INHIBITORS OF BACTERIAL GROWTH

    SciTech Connect (OSTI)

    Hobbs, D.

    2011-01-19

    Sodium titanates are ion-exchange materials that effectively bind a variety of metal ions over a wide pH range. Sodium titanates alone have no known adverse biological effects but metal-exchanged titanates (or metal titanates) can deliver metal ions to mammalian cells to alter cell processes in vitro. In this work, we test a hypothesis that metal-titanate compounds inhibit bacterial growth; demonstration of this principle is one prerequisite to developing metal-based, titanate-delivered antibacterial agents. Focusing initially on oral diseases, we exposed five species of oral bacteria to titanates for 24 h, with or without loading of Au(III), Pd(II), Pt(II), and Pt(IV), and measuring bacterial growth in planktonic assays through increases in optical density. In each experiment, bacterial growth was compared with control cultures of titanates or bacteria alone. We observed no suppression of bacterial growth by the sodium titanates alone, but significant (p < 0.05, two-sided t-tests) suppression was observed with metal-titanate compounds, particularly Au(III)-titanates, but with other metal titanates as well. Growth inhibition ranged from 15 to 100% depending on the metal ion and bacterial species involved. Furthermore, in specific cases, the titanates inhibited bacterial growth 5- to 375-fold versus metal ions alone, suggesting that titanates enhanced metal-bacteria interactions. This work supports further development of metal titanates as a novel class of antibacterials.

  13. Geothermal Case Studies

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Young, Katherine

    database.) In fiscal year 2015, NREL is working with universities to populate additional case studies on OpenEI. The goal is to provide a large enough dataset to start conducting analyses of exploration programs to identify correlations between successful exploration plans for areas with similar geologic occurrence models.

  14. Fuel Cell Case Study

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Kathy Loftus Global Leader, Sustainable Engineering, Maintenance & Energy Management Whole Foods Market, Inc. Fuel Cell Case Study 2 Holistic Approach from Development to Operation WFM Energy Management Negotiation Awareness Load Shaping Engineering Refrigeration HVAC Electrical Maintenance Performance Based Retailers Operational Practices Store Design & Construction Consultants Specifications Procurement Equipment Selection Life Cycle Costing Energy & Maintenance team can feedback

  15. Geothermal Case Studies

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Young, Katherine

    2014-09-30

    database.) In fiscal year 2015, NREL is working with universities to populate additional case studies on OpenEI. The goal is to provide a large enough dataset to start conducting analyses of exploration programs to identify correlations between successful exploration plans for areas with similar geologic occurrence models.

  16. Geothermal Energy Growth Continues, Industry Survey Reports

    Broader source: Energy.gov [DOE]

    A survey released by the Geothermal Energy Association (GEA) shows continued growth in the number of new geothermal power projects under development in the United States, a 20% increase since January of this year.

  17. Basic criteria for formation of growth twins in high stacking fault energy metals

    SciTech Connect (OSTI)

    Yu, K. Y.; Zhang, X. [Department of Materials Science and Engineering, Texas A and M University, College Station, Texas 77843 (United States) [Department of Materials Science and Engineering, Texas A and M University, College Station, Texas 77843 (United States); Department of Mechanical Engineering, Texas A and M University, College Station, Texas 77843 (United States); Bufford, D.; Chen, Y.; Liu, Y. [Department of Materials Science and Engineering, Texas A and M University, College Station, Texas 77843 (United States)] [Department of Materials Science and Engineering, Texas A and M University, College Station, Texas 77843 (United States); Wang, H. [Department of Materials Science and Engineering, Texas A and M University, College Station, Texas 77843 (United States) [Department of Materials Science and Engineering, Texas A and M University, College Station, Texas 77843 (United States); Department of Electrical and Computer Engineering, Texas A and M University, College Station, Texas 77843 (United States)

    2013-10-28

    Nanotwinned metals received significant interest lately as twin boundaries may enable simultaneous enhancement of strength, ductility, thermal stability, and radiation tolerance. However, nanotwins have been the privilege of metals with low-to-intermediate stacking fault energy (SFE). Recent scattered studies show that nanotwins could be introduced into high SFE metals, such as Al. In this paper, we examine several sputter-deposited, (111) textured Ag/Al, Cu/Ni, and Cu/Fe multilayers, wherein growth twins were observed in Al, Ni, and face-centered cubic (fcc) Fe. The comparisons lead to two important design criteria that dictate the introduction of growth twins in high SFE metals. The validity of these criteria was then examined in Ag/Ni multilayers. Furthermore, another twin formation mechanism in high SFE metals was discovered in Ag/Ni system.

  18. Driving Economic Growth: Advanced Technology Vehicles Manufacturing |

    Office of Environmental Management (EM)

    Department of Energy Driving Economic Growth: Advanced Technology Vehicles Manufacturing Driving Economic Growth: Advanced Technology Vehicles Manufacturing With $8 billion in loans and commitments to projects that have supported the production of more than 4 million fuel-efficient cars and more than 35,000 direct jobs across eight states, the Advanced Technology Vehicles Manufacturing (ATVM) loan program has played a key role in helping the American auto industry propel the resurgence of

  19. Better Buildings Residential Network Factsheet: Case Study: Partnerships

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Better Buildings Residential Network case studies feature members to fulfill our mission to share best practices and learn from one another to increase the number of homes that are energy efficient. GTECH (Growth Through Energy and Community Health) Strategies is a nonprofit member that kicked off its first year implementing an innovative new initiative called the Healthy Homes Incentive Program (HHIP), which promotes home energy upgrades to Allegheny County, Pennsylvania, residents as a way to

  20. A pathway for the growth of core-shell Pt-Pd nanoparticles

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Narula, Chaitanya Kumar; Yang, Xiaofan; Li, Chen; Pennycook, Stephen J; Lupini, Andrew R

    2015-10-12

    In this study, the aging of both Pt-Pd nanoparticles and core-shell Pt-Pd nanoparticles has been reported to result in alloying of Pt with Pd. In comparison to monometallic Pt catalysts, the growth of Pd-Pt bimetallics is slower; however, the mechanism of growth of particles and the mechanism by which Pd improves the hydrothermal durability of bimetallic Pd-Pt particles remains uncertain. In our work on hydrothermal aging of core-shell Pt-Pd nanoparticles, synthesized by solution methods, with varying Pd:Pt ratio of 1:4, 1:1, and 4:1, we compare the growth of core-shell Pt-Pd nanoparticles and find that particles grow by migrating and joiningmore » together. The unique feature of the observed growth is that Pd shells from both particles open up and join, allowing the cores to merge. At high temperatures, alloying occurs in good agreement with reports by other workers.« less

  1. Apparatus for silicon web growth of higher output and improved growth stability

    DOE Patents [OSTI]

    Duncan, Charles S.; Piotrowski, Paul A.

    1989-01-01

    This disclosure describes an apparatus to improve the web growth attainable from prior web growth configurations. This apparatus modifies the heat loss at the growth interface in a manner that minimizes thickness variations across the web, especially regions of the web adjacent to the two bounding dendrites. In the unmodified configuration, thinned regions of web, adjacent to the dendrites, were found to be the origin of crystal degradation which ultimately led to termination of the web growth. According to the present invention, thinning adjacent to the dendrites is reduced and the incidence of crystal degradation is similarly reduced.

  2. FES Case Study Worksheets

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Worksheets FES Case Study Worksheets This workshop is closed, and the worksheets can no longer be edited. If you have questions, please report any problems or suggestions for improvement to Richard Gerber (ragerber@lbl.gov). Please choose your worksheet template: Lee Berry, Paul Bonoli, David Green [Read] Jeff Candy [Read] CS Chang [Read] Stephane Ethier [Read] Alex Friedman [Read] Kai Germaschewski [Read] Martin Greenwald [Read] Stephen Jardin [Read] Charlson Kim [Read] Scott Kruger [Read]

  3. Emittance growth of an nonequilibrium intense electron beam in a transport channel with discrete focusing

    SciTech Connect (OSTI)

    Carlsten, B.E.

    1997-02-01

    The author analyzes the emittance growth mechanisms for a continuous, intense electron beam in a focusing transport channel, over distances short enough that the beam does not reach equilibrium. The emittance grows from the effect of nonlinear forces arising from (1) current density nonuniformities, (2) energy variations leading to nonlinearities in the space-charge force even if the current density is uniform, (3) axial variations in the radial vector potential, (4) an axial velocity shear along the beam, and (5) an energy redistribution of the beam as the beam compresses or expands. The emittance growth is studied analytically and numerically for the cases of balanced flow, tight focusing, and slight beam scalloping, and is additionally studied numerically for an existing 6-MeV induction linear accelerator. Rules for minimizing the emittance along a beamline are established. Some emittance growth will always occur, both from current density nonuniformities that arise along the transport and from beam radius changes along the transport.

  4. Growth Mode and Substrate Symmetry Dependent Strain in Epitaxial...

    Office of Scientific and Technical Information (OSTI)

    Growth Mode and Substrate Symmetry Dependent Strain in Epitaxial Graphene. Citation Details In-Document Search Title: Growth Mode and Substrate Symmetry Dependent Strain in...

  5. OECD-Fostering Innovation for Green Growth | Open Energy Information

    Open Energy Info (EERE)

    Fostering Innovation for Green Growth Jump to: navigation, search Tool Summary LAUNCH TOOL Name: OECD-Fostering Innovation for Green Growth AgencyCompany Organization:...

  6. Indonesia-Low Carbon Growth Project | Open Energy Information

    Open Energy Info (EERE)

    Growth Project Jump to: navigation, search Name Indonesia Low Carbon Growth Project AgencyCompany Organization United Kingdom Department for International Development Partner...

  7. Kenya-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Kenya-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  8. India-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name India-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  9. Brazil-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Brazil-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  10. Poland-Low Carbon Growth Country Studies Program | Open Energy...

    Open Energy Info (EERE)

    Low Carbon Growth Country Studies Program Jump to: navigation, search Name Poland-Low Carbon Growth Country Studies Program AgencyCompany Organization Energy Sector Management...

  11. Guyana-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Guyana-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  12. Mexico-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Mexico-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  13. Malaysia-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    Malaysia-ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Malaysia-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks,...

  14. Indonesia-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Indonesia-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  15. Egypt-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Egypt-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  16. Ethiopia-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    Ethiopia-ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name Ethiopia-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks,...

  17. Republic of Macedonia-Low Carbon Growth Country Studies Program...

    Open Energy Info (EERE)

    Low Carbon Growth Country Studies Program Jump to: navigation, search Name Republic of Macedonia-Low Carbon Growth Country Studies Program AgencyCompany Organization Energy...

  18. Before the Subcommittee on Economic Growth, Job Creation and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Economic Growth, Job Creation and Regulatory Affairs - House Committee on Oversight and Governmant Reform Before the Subcommittee on Economic Growth, Job Creation and Regulatory ...

  19. Thailand-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    search Name Thailand-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI) Partner Korea International Cooperation Agency (KOICA)...

  20. Cambodia-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    search Name Cambodia-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI) Partner Korea International Cooperation Agency (KOICA)...

  1. Global Green Growth Institute (GGGI) | Open Energy Information

    Open Energy Info (EERE)

    "GGGI is dedicated to pioneering and diffusing a new model of economic growth, known as "green growth," that simultaneously targets key aspects of economic performance, such as...

  2. Green Growth e-Learning | Open Energy Information

    Open Energy Info (EERE)

    Tool Summary LAUNCH TOOL Name: Green Growth e-Learning AgencyCompany Organization: Green Growth Best Practice Initiative (GGBPI) Focus Area: Economic Development, Energy...

  3. Peru-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    navigation, search Name Peru-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI) Partner Korea International Cooperation Agency (KOICA)...

  4. Jordan-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    navigation, search Name Jordan-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI) Partner Korea International Cooperation Agency (KOICA)...

  5. Ethiopia-Green Growth Planning | Open Energy Information

    Open Energy Info (EERE)

    search Name Ethiopia-Green Growth Planning AgencyCompany Organization Global Green Growth Institute (GGGI), Korea International Cooperation Agency (KOICA) Partner...

  6. Understanding Cost Growth and Performance Shortfalls in Pioneer...

    Office of Environmental Management (EM)

    Cost Growth and Performance Shortfalls in Pioneer Process Plants Understanding Cost Growth and Performance Shortfalls in Pioneer Process Plants This report presents an empirical...

  7. Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure Development Growth of the NGV Market: Lessons Learned Roadmap for Infrastructure Development Presented at ...

  8. Synthesis of segmented silica rods by growth temperature regulation...

    Office of Scientific and Technical Information (OSTI)

    silica rods by growth temperature regulation Citation Details In-Document Search Title: Synthesis of segmented silica rods by growth temperature regulation Authors: Sharma, ...

  9. ClimateWorks-Egypt-Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks-Egypt-Low Carbon Growth Planning Support Redirect page Jump to: navigation, search REDIRECT ClimateWorks Low Carbon Growth Planning Support Retrieved from "http:...

  10. Low Carbon Growth: a Potential Path for Mexico - GHG Abatement...

    Open Energy Info (EERE)

    "ESMAP Low Carbon Growth Country Studies Program" Retrieved from "http:en.openei.orgwindex.php?titleLowCarbonGrowth:aPotentialPathforMexico-GHGAbatementCostCurve&...

  11. Low Carbon Green Growth: Integrated Policy Approach to Climate...

    Open Energy Info (EERE)

    Growth: Integrated Policy Approach to Climate Change for Asia-Pacific Developing Countries Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Low Carbon Green Growth:...

  12. Ghana Goes for Green Growth: National Engagement on Climate Change...

    Open Energy Info (EERE)

    Ghana Goes for Green Growth: National Engagement on Climate Change Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Ghana Goes for Green Growth: National Engagement on...

  13. Enhancing Plant Growth and Stress Tolerance through Use of Fungi...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Enhancing Plant Growth and Stress Tolerance through Use of Fungi and Bacteria that Comprise Plant Microbiomes Enhancing Plant Growth and Stress Tolerance through Use of Fungi and...

  14. From Climate Finance to Financing Green Growth | Open Energy...

    Open Energy Info (EERE)

    green growth and the importance of developing the right policies to support a transition towards the low carbon economy. It assesses the financing needs of green growth in...

  15. China-ClimateWorks Low Carbon Growth Planning Support | Open...

    Open Energy Info (EERE)

    ClimateWorks Low Carbon Growth Planning Support Jump to: navigation, search Name China-Low Carbon Growth Planning Support AgencyCompany Organization ClimateWorks, Project...

  16. Annual Energy Outlook 2014 foresees growth of LNG as a fuel for railroads

    Gasoline and Diesel Fuel Update (EIA)

    14, 2014 Annual Energy Outlook 2014 foresees growth of LNG as a fuel for railroads The U.S. Energy Information Administration expects liquefied natural gas, or LNG, to play an increasing role in powering freight locomotives in the coming years. EIA's Reference case, in its recently released Annual Energy Outlook 2014 indicates that growing natural gas production and lower natural gas spot prices compared to crude oil prices could provide significant cost savings for locomotives that use LNG as a

  17. Systematic Comparison of Operating Reserve Methodologies: Preprint

    SciTech Connect (OSTI)

    Ibanez, E.; Krad, I.; Ela, E.

    2014-04-01

    Operating reserve requirements are a key component of modern power systems, and they contribute to maintaining reliable operations with minimum economic impact. No universal method exists for determining reserve requirements, thus there is a need for a thorough study and performance comparison of the different existing methodologies. Increasing penetrations of variable generation (VG) on electric power systems are posed to increase system uncertainty and variability, thus the need for additional reserve also increases. This paper presents background information on operating reserve and its relationship to VG. A consistent comparison of three methodologies to calculate regulating and flexibility reserve in systems with VG is performed.

  18. ARM - Field Campaign - ARRA AERI Comparison

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    govCampaignsARRA AERI Comparison ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : ARRA AERI Comparison 2011.01.07 - 2011.01.23 Lead Scientist : David Turner For data sets, see below. Abstract The ARM program, using stimulus funds from the ARRA, acquired a new AERI instrument for the SGP site. This new instrument was run side-by-side with the operational AERI at the SGP central facility to evaluate its

  19. Performance comparison between Edison and Hopper

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Performance comparison between Edison and Hopper Performance comparison between Edison and Hopper Edison compute node memory was upgraded to 1866 MHz from 1600 MHz on Jan 16, 2015. We rerun the SSP applications in dedicted or semi-dedicated mode on Edison again, and have observed 2-9% of increase in performance with the NERSC 6 application benchmark. The table below is the updated performance data: Application CAM GAMESS GTC IMPACT-T MAESTRO MILC PARATEC Concurrency 240 1024 2048 1024 2048 8192

  20. Novel method for carbon nanofilament growth on carbon fibers

    SciTech Connect (OSTI)

    Phillips, Johathan; Luhrs, Claudia; Terani, Mehran; Al - Haik, Marwan; Garcia, Daniel; Taha, Mahmoud R

    2009-01-01

    Fiber reinforced structural composites such as fiber reinforced polymers (FRPs) have proven to be key materials for blast mitigation due to their enhanced mechanical performance. However, there is a need to further increase total energy absorption of the composites in order to retain structural integrity in high energy environments, for example, blast events. Research has shown that composite failure in high energy environments can be traced to their relatively low shear strength attributed to the limited bond strength between the matrix and the fibers. One area of focus for improving the strength of composite materials has been to create 'multi-scale' composites. The most common approach to date is to introduce carbon nanotubes into a more traditional composite consisting of epoxy with embedded micron scale fibers. The inclusion of carbon nanotubes (CNT) clearly toughens different matrices. Depositing CNT in brittle matrix increases stiffness by orders of magnitude. Currently, this approach to create multiscale composites is limited due to the difficulty of dispersing significant amounts of nanotubes. It has repeatedly been reported that phase separation occurs above relatively low weight percent loading (ca. 3%) due to the strong van der Waals forces between CNTs compared with that between CNT and polymer. Hence, the nanotubes tend to segregate and form inclusions. One means to prevent nanotube or nanofilament agglomeration is to anchor one end of the nanostructure, thereby creating a stable multi-phase structure. This is most easily done by literally growing the CNTs directly on micron scale fibers. Recently, CNT were grown on carbon fibers, both polyacrylonitrile- (PAN-) and pitch-based, by hot filament chemical vapor deposition (HFCVD) using H2 and CH4 as precursors. Nickel clusters were electrodeposited on the fiber surfaces to catalyze the growth and uniform CNT coatings were obtained on both the PAN- and pitch-based carbon fibers. Multiwalled CNTs with smooth walls and low impurity content were grown. Carbon nanofibers were also grown on a carbon fiber cloth using plasma enhanced chemical vapor deposition (CVD) from a mixture of acetylene and ammonia. In this case, a cobalt colloid was used to achieve a good coverage of nanofibers on carbon fibers in the cloth. Caveats to CNT growth include damage in the carbon fiber surface due to high-temperatures (>800 C). More recently, Qu et al. reported a new method for uniform deposition of CNT on carbon fibers. However, this method requires processing at 1100 C in the presence of oxygen and such high temperature is anticipated to deepen the damage in the carbon fibers. In the present work, multi-scale filaments (herein, linear carbon structures with multi-micron diameter are called 'fibers', all structures with sub-micron diameter are called 'filaments') were created with a low temperature (ca. 550 C) alternative to CVD growth of CNTs. Specifically, nano-scale filaments were rapidly generated (> 10 microns/hour) on commercial micron scale fibers via catalytic (Pd particles) growth from a fuel rich combustion environment at atmospheric pressure. This atmospheric pressure process, derived from the process called Graphitic Growth by Design (GSD), is rapid, the maximum temperature low enough (below 700 C) to avoid structural damage and the process inexpensive and readily scalable. In some cases, a significant and unexpected aspect of the process was the generation of 'three scale' materials. That is, materials with these three size characteristics were produced: (1) micrometer scale commercial PAN fibers, (2) a layer of 'long' sub-micrometer diameter scale carbon filaments, and (3) a dense layer of 'short' nanometer diameter filaments.

  1. Growth Kinetics and Modeling of Direct Oxynitride Growth with NO-O2 Gas Mixtures

    SciTech Connect (OSTI)

    Everist, Sarah; Nelson, Jerry; Sharangpani, Rahul; Smith, Paul Martin; Tay, Sing-Pin; Thakur, Randhir

    1999-05-03

    We have modeled growth kinetics of oxynitrides grown in NO-O2 gas mixtures from first principles using modified Deal-Grove equations. Retardation of oxygen diffusion through the nitrided dielectric was assumed to be the dominant growth-limiting step. The model was validated against experimentally obtained curves with good agreement. Excellent uniformity, which exceeded expected walues, was observed.

  2. Role of nucleation in nanodiamond film growth

    SciTech Connect (OSTI)

    Lifshitz, Y.; Lee, C.H.; Wu, Y.; Zhang, W.J.; Bello, I.; Lee, S.T.

    2006-06-12

    Nanodiamond films were deposited using different microwave plasma chemical vapor deposition schemes following several nucleation pretreatment methods. The nucleation efficiency and the films structure were investigated using scanning and transmission electron microscopy and Raman spectroscopy. C{sub 2} dimer growth (CH{sub 4} and H{sub 2} in 90% Ar) cannot nucleate diamond and works only on existing diamond surfaces. The methyl radical process (up to 20% CH{sub 4} in H{sub 2}) allows some nucleation probability on appropriate substrates. Prolonged bias enhanced nucleation initiates both diamond nucleation and growth. C{sub 2} dimer growth results in pure nanodiamond free of amorphous carbon, while prolonged bias enhanced nucleation forms an amorphous carbon/nanodiamond composite.

  3. Efg Crystal Growth Apparatus And Method

    DOE Patents [OSTI]

    Mackintosh, Brian H. (Concord, MA); Ouellette, Marc (Nashua, NH)

    2003-05-13

    An improved mechanical arrangement controls the introduction of silicon particles into an EFG (Edge-defined Film-fed Growth) crucible/die unit for melt replenishment during a crystal growth run. A feeder unit injects silicon particles upwardly through a center hub of the crucible/die unit and the mechanical arrangement intercepts the injected particles and directs them so that they drop into the melt in a selected region of the crucible and at velocity which reduces splashing, whereby to reduce the likelihood of interruption of the growth process due to formation of a solid mass of silicon on the center hub and adjoining components. The invention also comprises use of a Faraday ring to alter the ratio of the electrical currents flowing through primary and secondary induction heating coils that heat the crucible die unit and the mechanical arrangement.

  4. Crystal growth and annealing method and apparatus

    DOE Patents [OSTI]

    Gianoulakis, Steven E.; Sparrow, Robert

    2001-01-01

    A method and apparatus for producing crystals that minimizes birefringence even at large crystal sizes, and is suitable for production of CaF.sub.2 crystals. The method of the present invention comprises annealing a crystal by maintaining a minimal temperature gradient in the crystal while slowly reducing the bulk temperature of the crystal. An apparatus according to the present invention includes a thermal control system added to a crystal growth and annealing apparatus, wherein the thermal control system allows a temperature gradient during crystal growth but minimizes the temperature gradient during crystal annealing. An embodiment of the present invention comprises a secondary heater incorporated into a conventional crystal growth and annealing apparatus. The secondary heater supplies heat to minimize the temperature gradients in the crystal during the annealing process. The secondary heater can mount near the bottom of the crucible to effectively maintain appropriate temperature gradients.

  5. In-situ energy dispersive x-ray diffraction study of the growth of CuO nanowires by annealing method

    SciTech Connect (OSTI)

    Srivastava, Himanshu; Ganguli, Tapas; Deb, S. K.; Sant, Tushar; Poswal, H. K.; Sharma, Surinder M.

    2013-10-14

    The in-situ growth of CuO nanowires was studied by Energy Dispersive X-ray Diffraction (EDXRD) to observe the mechanism of growth. The study was carried out for comparison at two temperaturesat 500 C, the optimum temperature of the nanowires growth, and at 300 C just below the temperature range of the growth. The in situ observation revealed the successive oxidation of Cu foil to Cu{sub 2}O layer and finally to CuO layer. Further analysis showed the presence of a compressive stress in CuO layer due to interface at CuO and Cu{sub 2}O layers. The compressive stress was found to increase with the growth of the nanowires at 500 C while it relaxed with the growth of CuO layer at 300 C. The present results do not support the existing model of stress relaxation induced growth of nanowires. Based on the detailed Transmission Electron Microscope, Scanning Electron Microscope, and EDXRD results, a microstructure based growth model has been suggested.

  6. Klebsiella pneumoniae inoculants for enhancing plant growth

    DOE Patents [OSTI]

    Triplett, Eric W. (Middleton, WI); Kaeppler, Shawn M. (Oregon, WI); Chelius, Marisa K. (Greeley, CO)

    2008-07-01

    A biological inoculant for enhancing the growth of plants is disclosed. The inoculant includes the bacterial strains Herbaspirillum seropedicae 2A, Pantoea agglomerans P101, Pantoea agglomerans P102, Klebsiella pneumoniae 342, Klebsiella pneumoniae zmvsy, Herbaspirillum seropedicae Z152, Gluconacetobacter diazotrophicus PA15, with or without a carrier. The inoculant also includes strains of the bacterium Pantoea agglomerans and K. pneumoniae which are able to enhance the growth of cereal grasses. Also disclosed are the novel bacterial strains Herbaspirillum seropedicae 2A, Pantoea agglomerans P101 and P102, and Klebsiella pneumoniae 342 and zmvsy.

  7. Direct growth of graphene on Si(111)

    SciTech Connect (OSTI)

    Thanh Trung, Pham Joucken, Frdric; Colomer, Jean-Franois; Robert, Sporken; Campos-Delgado, Jessica; Raskin, Jean-Pierre; Hackens, Benot; Santos, Cristiane N.

    2014-06-14

    Due to the need of integrated circuit in the current silicon technology, the formation of graphene on Si wafer is highly desirable, but is still a challenge for the scientific community. In this context, we report the direct growth of graphene on Si(111) wafer under appropriate conditions using an electron beam evaporator. The structural quality of the material is investigated in detail by reflection high energy electron diffraction, Auger electron spectroscopy, X-ray photoemission spectroscopy, Raman spectroscopy, high resolution scanning electron microscopy, atomic force microscopy, and scanning tunneling microscopy. Our experimental results confirm that the quality of graphene is strongly dependent on the growth time during carbon atoms deposition.

  8. SEP CASE STUDY WEBINAR: MEDIMMUNE

    Broader source: Energy.gov [DOE]

    This Measurement and Verification Case Study webinar is the first in a series of case study webinars to highlight the successes of facilities that have achieved Superior Energy Performance (SEP)...

  9. Comparison of Software Models for Energy Savings from Cool Roofs

    SciTech Connect (OSTI)

    New, Joshua Ryan; Miller, William A; Huang, Yu; Levinson, Ronnen

    2014-01-01

    A web-based Roof Savings Calculator (RSC) has been deployed for the United States Department of Energy as an industry-consensus tool to help building owners, manufacturers, distributors, contractors and researchers easily run complex roof and attic simulations. This tool employs modern web technologies, usability design, and national average defaults as an interface to annual simulations of hour-by-hour, whole-building performance using the world-class simulation tools DOE-2.1E and AtticSim in order to provide estimated annual energy and cost savings. In addition to cool reflective roofs, RSC simulates multiple roof and attic configurations including different roof slopes, above sheathing ventilation, radiant barriers, low-emittance roof surfaces, duct location, duct leakage rates, multiple substrate types, and insulation levels. A base case and energy-efficient alternative can be compared side-by-side to estimate monthly energy. RSC was benchmarked against field data from demonstration homes in Ft. Irwin, California; while cooling savings were similar, heating penalty varied significantly across different simulation engines. RSC results reduce cool roofing cost-effectiveness thus mitigating expected economic incentives for this countermeasure to the urban heat island effect. This paper consolidates comparison of RSC s projected energy savings to other simulation engines including DOE-2.1E, AtticSim, Micropas, and EnergyPlus, and presents preliminary analyses. RSC s algorithms for capturing radiant heat transfer and duct interaction in the attic assembly are considered major contributing factors to increased cooling savings and heating penalties. Comparison to previous simulation-based studies, analysis on the force multiplier of RSC cooling savings and heating penalties, the role of radiative heat exchange in an attic assembly, and changes made for increased accuracy of the duct model are included.

  10. Melt dumping in string stabilized ribbon growth

    DOE Patents [OSTI]

    Sachs, Emanuel M. (42 Old Middlesex Rd., Belmont, MA 02178)

    1986-12-09

    A method and apparatus for stabilizing the edge positions of a ribbon drawn from a melt includes the use of wettable strings drawn in parallel up through the melt surface, the ribbon being grown between the strings. A furnace and various features of the crucible used therein permit continuous automatic growth of flat ribbons without close temperature control or the need for visual inspection.

  11. Growth Of Oriented Crystals At Polymerized Membranes

    DOE Patents [OSTI]

    Charych, Deborah H. (Albany, CA), Berman, Amir (Ben-Shiva, IL)

    2000-01-25

    The present invention relates to methods and compositions for the growth and alignment of crystals at biopolymeric films. The methods and compositions of the present invention provide means to generate a variety of dense crystalline ceramic films, with totally aligned crystals, at low temperatures and pressures, suitable for use with polymer and plastic substrates.

  12. Distributed Wind Policy Comparison Tool Website | Open Energy...

    Open Energy Info (EERE)

    TOOL Name: Distributed Wind Policy Comparison Tool Website Focus Area: Renewable Energy Topics: Security & Reliability Website: www.eformativeoptions.comdwpolicytool...

  13. Discussion on a Code Comparison Effort for the Geothermal Technologies

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Program | Department of Energy Discussion on a Code Comparison Effort for the Geothermal Technologies Program Discussion on a Code Comparison Effort for the Geothermal Technologies Program Code comparison presentation by Mark White of PNNL at the 2012 Peer Review meeting on May 10. PDF icon gtp_2012peerreview_pnnl_white.pdf More Documents & Publications PNNL Support of the DOE GTO Model Comparison Activity Methane Hydrate Annual Reports Fiscal Year 2014 ASCEM Status Report

  14. Millifluidics for time-resolved mapping of the growth of gold nanostructures

    SciTech Connect (OSTI)

    Sai Krishna, Katla; Navin, Chelliah; Biswas, Sanchita; Singh, Varshni; Ham, Kyungmin; Bovencamp, L. S.; Theegala, Chandra; Miller, Jeffrey T; Spivey, James J.; Kumar, Challa S.S.R.

    2013-04-10

    Innovative in situ characterization tools are essential for understanding the reaction mechanisms leading to the growth of nanoscale materials. Though techniques, such as in situ transmission X-ray microscopy, fast single-particle spectroscopy, small-angle X-ray scattering, etc., are currently being developed, these tools are complex, not easily accessible, and do not necessarily provide the temporal resolution required to follow the formation of nanomaterials in real time. Here, we demonstrate for the first time the utility of a simple millifluidic chip for an in situ real time analysis of morphology and dimension-controlled growth of gold nano- and microstructures with a time resolution of 5 ms. The structures formed were characterized using synchrotron radiation-based in situ X-ray absorption spectroscopy, 3-D X-ray tomography, and high-resolution electron microscopy. These gold nanostructures were found to be catalytically active for conversion of 4-nitrophenol into 4-aminophenol, providing an example of the potential opportunities for time-resolved analysis of catalytic reactions. While the investigations reported here are focused on gold nanostructures, the technique can be applied to analyze the time-resolved growth of other types of nanostructured metals and metal oxides. With the ability to probe at least a 10-fold higher concentrations, in comparison with traditional microfluidics, the tool has potential to revolutionize a broad range of fields from catalysis, molecular analysis, biodefense, and molecular biology.

  15. Growth and Characterization of MBE Parametric Variations Upon Polarization Independent Strained Films

    SciTech Connect (OSTI)

    Theda Daniels-Race

    2003-04-30

    This project was designed to comprehensively investigate the effects of molecular beam epitaxy (MBE) growth variations upon tensile-strained films. Using two dimensional (2-D) structures, such as quantum wells of variable configurations, we worked to observe the electro-optical response of polarization independence. The latter had been studied for compressively strained systems. However, the proof of principle for the feasibility of tensile-strained single and double quantum wells, particularly in the GaAs as opposed to the InP material system, had been much less investigated by comparison. The significance of this project, from a Basic Energy Sciences perspective, has been in its contribution to the understanding of how MBE parameters and sample design effect the physics of strained materials which themselves have been tailored to react with polarization insensitivity. Fundamental issues of materials structure control, growth parameter modifications, and characterization methods were investigated. Both single and double quantum well systems were used with both symmetric and asymmetric well widths for the latter. In this work, we essentially investigated both the growth of and potential applications for quantum based structures that use tensile strain to induce polarization independence.

  16. Metrics for comparison of crystallographic maps

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Urzhumtsev, Alexandre; Afonine, Pavel V.; Lunin, Vladimir Y.; Terwilliger, Thomas C.; Adams, Paul D.

    2014-10-01

    Numerical comparison of crystallographic contour maps is used extensively in structure solution and model refinement, analysis and validation. However, traditional metrics such as the map correlation coefficient (map CC, real-space CC or RSCC) sometimes contradict the results of visual assessment of the corresponding maps. This article explains such apparent contradictions and suggests new metrics and tools to compare crystallographic contour maps. The key to the new methods is rank scaling of the Fourier syntheses. The new metrics are complementary to the usual map CC and can be more helpful in map comparison, in particular when only some of their aspects,more » such as regions of high density, are of interest.« less

  17. Comparison of Virtualization and Containerization Techniques for

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    High-Performance Computing | Argonne Leadership Computing Facility Comparison of Virtualization and Containerization Techniques for High-Performance Computing Event Sponsor: Mathematics and Computer Science Division Seminar Start Date: Feb 9 2016 - 12:00pm Building/Room: Building 240/Room 4301 Location: Argonne National Laboratory Speaker(s): Balaji Subramaniam Host: Kate Keahey High Performance Computing (HPC) users have traditionally used dedicated clusters hosted in national laboratories

  18. Workplace Charging: Comparison of Sustainable Commuting Options

    Broader source: Energy.gov (indexed) [DOE]

    Workplace Charging: Comparison of Sustainable Commuting Options November 18, 2014 Austin Brown National Renewable Energy Laboratory vehicles.energy.gov Relevance of ROI calculation * Value Proposition for Employers - How are Lifecycle/Scope 3 GHG emissions affected? - What are my (employer) direct costs? - What is the Return on Investment (ROI)? - What are possible ancillary benefits? * How does Workplace Charging compare to: - Transit Subsidies - Vanpool Subsidies - Bike Purchase Subsidies 2 -

  19. Explosively separable casing

    DOE Patents [OSTI]

    Jacobson, Albin K. (Albuquerque, NM); Rychnovsky, Raymond E. (Livermore, CA); Visbeck, Cornelius N. (Livermore, CA)

    1985-01-01

    An explosively separable casing including a cylindrical afterbody and a circular cover for one end of the afterbody is disclosed. The afterbody has a cylindrical tongue extending longitudinally from one end which is matingly received in a corresponding groove in the cover. The groove is sized to provide a pocket between the end of the tongue and the remainder of the groove so that an explosive can be located therein. A seal is also provided between the tongue and the groove for sealing the pocket from the atmosphere. A frangible holding device is utilized to hold the cover to the afterbody. When the explosive is ignited, the increase in pressure in the pocket causes the cover to be accelerated away from the afterbody. Preferably, the inner wall of the afterbody is in the same plane as the inner wall of the tongue to provide a maximum space for storage in the afterbody and the side wall of the cover is thicker than the side wall of the afterbody so as to provide a sufficiently strong surrounding portion for the pocket in which the explosion takes place. The detonator for the explosive is also located on the cover and is carried away with the cover during separation. The seal is preferably located at the longitudinal end of the tongue and has a chevron cross section.

  20. Method for solid state crystal growth

    DOE Patents [OSTI]

    Nolas, George S.; Beekman, Matthew K.

    2013-04-09

    A novel method for high quality crystal growth of intermetallic clathrates is presented. The synthesis of high quality pure phase crystals has been complicated by the simultaneous formation of both clathrate type-I and clathrate type-II structures. It was found that selective, phase pure, single-crystal growth of type-I and type-II clathrates can be achieved by maintaining sufficient partial pressure of a chemical constituent during slow, controlled deprivation of the chemical constituent from the primary reactant. The chemical constituent is slowly removed from the primary reactant by the reaction of the chemical constituent vapor with a secondary reactant, spatially separated from the primary reactant, in a closed volume under uniaxial pressure and heat to form the single phase pure crystals.

  1. Epitaxial growth of silicon for layer transfer

    DOE Patents [OSTI]

    Teplin, Charles; Branz, Howard M

    2015-03-24

    Methods of preparing a thin crystalline silicon film for transfer and devices utilizing a transferred crystalline silicon film are disclosed. The methods include preparing a silicon growth substrate which has an interface defining substance associated with an exterior surface. The methods further include depositing an epitaxial layer of silicon on the silicon growth substrate at the surface and separating the epitaxial layer from the substrate substantially along the plane or other surface defined by the interface defining substance. The epitaxial layer may be utilized as a thin film of crystalline silicon in any type of semiconductor device which requires a crystalline silicon layer. In use, the epitaxial transfer layer may be associated with a secondary substrate.

  2. Substrate solder barriers for semiconductor epilayer growth

    DOE Patents [OSTI]

    Drummond, T.J.; Ginley, D.S.; Zipperian, T.E.

    1989-05-09

    During the growth of compound semiconductors by epitaxial processes, substrates are typically mounted to a support. In modular beam epitaxy, mounting is done using indium as a solder. This method has two drawbacks: the indium reacts with the substrate, and it is difficult to uniformly wet the back of a large diameter substrate. Both of these problems have been successfully overcome by sputter coating the back of the substrate with a thin layer of tungsten carbide or tungsten carbide and gold. In addition to being compatible with the growth of high quality semiconductor epilayers this coating is also inert in all standard substrate cleaning etchants used for compound semiconductors, and provides uniform distribution of energy in radiant heating.

  3. Substrate solder barriers for semiconductor epilayer growth

    DOE Patents [OSTI]

    Drummond, T.J.; Ginley, D.S.; Zipperian, T.E.

    1987-10-23

    During the growth of compound semiconductors by epitaxial processes, substrates are typically mounted to a support. In molecular beam epitaxy, mounting is done using indium as a solder. This method has two drawbacks: the indium reacts with the substrate, and it is difficult to uniformly wet the back of a large diameter substrate. Both of these problems have been successfully overcome by sputter coating the back of the substrate with a thin layer of tungsten carbide or tungsten carbide and gold. In addition to being compatible with the growth of high quality semiconductor epilayers this coating is also inert in all standard substate cleaning etchants used for compound semiconductors, and provides uniform distribution of energy in radiant heating. 1 tab.

  4. Substrate solder barriers for semiconductor epilayer growth

    DOE Patents [OSTI]

    Drummond, Timothy J.; Ginley, David S.; Zipperian, Thomas E.

    1989-01-01

    During the growth of compound semiconductors by epitaxial processes, substrates are typically mounted to a support. In modular beam epitaxy, mounting is done using indium as a solder. This method has two drawbacks: the indium reacts with the substrate, and it is difficult to uniformly wet the back of a large diameter substrate. Both of these problems have been successfully overcome by sputter coating the back of the substrate with a thin layer of tungsten carbide or tungsten carbide and gold. In addition to being compatible with the growth of high quality semiconductor epilayers this coating is also inert in all standard substrate cleaning etchants used for compound semiconductors, and provides uniform distribution of energy in radiant heating.

  5. A Screening Model to Predict Microalgae Biomass Growth in Photobioreactors and Raceway Ponds

    SciTech Connect (OSTI)

    Huesemann, Michael H.; Van Wagenen, Jonathan M.; Miller, Tyler W.; Chavis, Aaron R.; Hobbs, Watts B.; Crowe, Braden J.

    2013-06-01

    A microalgae biomass growth model was developed for screening novel strains for their potential to exhibit high biomass productivities under nutrient-replete conditions in photobioreactors or outdoor ponds. Growth is modeled by first estimating the light attenuation by biomass according to Beer-Lamberts law, and then calculating the specific growth rate in discretized culture volume slices that receive declining light intensities due to attenuation. The model requires only two physical and two species-specific biological input parameters, all of which are relatively easy to determine: incident light intensity, culture depth, as well as the biomass light absorption coefficient and the specific growth rate as a function of light intensity. Roux bottle culture experiments were performed with Nannochloropsis salina at constant temperature (23 C) at six different incident light intensities (5, 10, 25, 50, 100, 250, and 850 ?mol/m2? sec) to determine both the specific growth rate under non-shading conditions and the biomass light absorption coefficient as a function of light intensity. The model was successful in predicting the biomass growth rate in these Roux bottle cultures during the light-limited linear phase at different incident light intensities. Model predictions were moderately sensitive to minor variations in the values of input parameters. The model was also successful in predicting the growth performance of Chlorella sp. cultured in LED-lighted 800 L raceway ponds operated at constant temperature (30 C) and constant light intensity (1650 ?mol/m2? sec). Measurements of oxygen concentrations as a function of time demonstrated that following exposure to darkness, it takes at least 5 seconds for cells to initiate dark respiration. As a result, biomass loss due to dark respiration in the aphotic zone of a culture is unlikely to occur in highly mixed small-scale photobioreactors where cells move rapidly in and out of the light. By contrast, as supported also by the growth model, biomass loss due to dark respiration occurs in the dark zones of the relatively less well mixed pond cultures. In addition to screening novel microalgae strains for high biomass productivities, the model can also be used for optimizing the pond design and operation. Additional research is needed to validate the biomass growth model for other microalgae species and for the more realistic case of fluctuating temperatures and light intensities observed in outdoor pond cultures.

  6. Career Growth | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Growth | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Library Bios Congressional Testimony Fact Sheets Newsletters Press Releases Photo Gallery Jobs Apply for Our Jobs Our Jobs Working at NNSA Blog Home /

  7. Growth process for gallium nitride porous nanorods

    DOE Patents [OSTI]

    Wildeson, Isaac Harshman; Sands, Timothy David

    2015-03-24

    A GaN nanorod and formation method. Formation includes providing a substrate having a GaN film, depositing SiN.sub.x on the GaN film, etching a growth opening through the SiN.sub.x and into the GaN film, growing a GaN nanorod through the growth opening, the nanorod having a nanopore running substantially through its centerline. Focused ion beam etching can be used. The growing can be done using organometallic vapor phase epitaxy. The nanopore diameter can be controlled using the growth opening diameter or the growing step duration. The GaN nanorods can be removed from the substrate. The SiN.sub.x layer can be removed after the growing step. A SiO.sub.x template can be formed on the GaN film and the GaN can be grown to cover the SiO.sub.x template before depositing SiN.sub.x on the GaN film. The SiO.sub.x template can be removed after growing the nanorods.

  8. 1979 revenue growth belies utility industry problems

    SciTech Connect (OSTI)

    Lincicome, R.

    1980-06-01

    Despite growth in revenues during 1979, electric utilities are greatly troubled by high inflation, restricted capital, and the lack of rate relief from utility commissions. The growth, although smaller than normal, will likely convince commissions to respond to rate increase requests by authorizing only the smallest possible increases. With inflationary pressures eroding utility companies' financial base, the benefits of rate increases are wiped out after a year or so, necessitating a return to the commissions for futher adjustments. This up-down cycling is reflected in the report of the performances of the top one hundred utility companies. Earning growth statistics, sales data, financial statistics, and company performances (electric sales, customers served, revenues, and after-tax net income) of top one hundred electric utilities are given in separate tables for 1979. Overall, kWh sales were up 2.9%; revenues were up 13.4%; net income was up 8.1%; and overall earnings performance was a weak increase of 9.4%. (SAC)

  9. Theoretical priors on modified growth parametrisations

    SciTech Connect (OSTI)

    Song, Yong-Seon; Hollenstein, Lukas; Caldera-Cabral, Gabriela; Koyama, Kazuya E-mail: Lukas.Hollenstein@unige.ch E-mail: Kazuya.Koyama@port.ac.uk

    2010-04-01

    Next generation surveys will observe the large-scale structure of the Universe with unprecedented accuracy. This will enable us to test the relationships between matter over-densities, the curvature perturbation and the Newtonian potential. Any large-distance modification of gravity or exotic nature of dark energy modifies these relationships as compared to those predicted in the standard smooth dark energy model based on General Relativity. In linear theory of structure growth such modifications are often parameterised by virtue of two functions of space and time that enter the relation of the curvature perturbation to, first, the matter over- density, and second, the Newtonian potential. We investigate the predictions for these functions in Brans-Dicke theory, clustering dark energy models and interacting dark energy models. We find that each theory has a distinct path in the parameter space of modified growth. Understanding these theoretical priors on the parameterisations of modified growth is essential to reveal the nature of cosmic acceleration with the help of upcoming observations of structure formation.

  10. Tests and analyses for fully plastic fracture mechanics of plane strain mode I crack growth

    SciTech Connect (OSTI)

    McClintock, F.A.; Parks, D.M.; Kim, Y.J.

    1995-12-31

    Under monotonic loading, structures should ideally be ductile enough to provide continued resistance during crack growth. For fully plastic crack growth in low strength alloys, existing asymptotic solutions for elastic-plastic growing cracks are not applicable because they reach the fracture strain only in regions small compared to the inhomogeneities of the actual fracture process. For the limiting case of non-hardening fully-plastic plane strain crack growth, in a number of geometries and loadings the near-tip fields are characterized in terms of three parameters: an effective angle 2{theta}{sub s} between a pair of slip planes, and the normal stress {sigma}{sub s} and the increment of displacement {delta}u{sub s} across the planes. This three-parameter characterization is in contrast to the one- or two-parameter (K or J and T or Q) characterization in linear or non-linear elastic fracture mechanics. These {theta}{sub s}, {sigma}{sub s}, and {delta}u{sub s} parameters are found form the far-field geometries and loadings through slip line fields or least upper bound analyses based on circular arcs. The resulting crack growth, in terms of the crack tip opening angle (CTOA), is a function of {theta}{sub s}, {sigma}{sub s}, and the material. The geometry of the crack growing between two moving slip planes emanating from its tip reduces this function to the critical fracture shear strain left behind the slip planes, {gamma}f, as a function of {sigma}{sub s}. {gamma}f({sigma}{sub s}) is found theoretically from a hole initiation and growth model. It is also found from preliminary fully plastic crack growth experiments on unequally grooved specimens with fixed-grip extension or 4-point bending of a 1018 CF steel.

  11. Technology Deployment Case Studies | Department of Energy

    Office of Environmental Management (EM)

    Deployment Technology Deployment Case Studies Technology Deployment Case Studies These case studies describe evaluations of energy-efficient technologies being used in federal...

  12. Better Buildings Residential Network Case Study: Partnerships...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Network Case Study: Partnerships Better Buildings Residential Network Case Study: Partnerships Better Buildings Residential Network Case Study: Partnerships, from the U.S. ...

  13. Geothermal Case Study Challenge | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Case Study Challenge Geothermal Case Study Challenge Geothermal Case Study Challenge The ... student competition in exploration research to engage students pursuing STEM careers ...

  14. Patrick Case | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Blake Case Larry Case Patrick Case Dorothy Coker Gordon Fee Linda Fellers Louis Freels Marie Guy Nathan Henry Agnes Houser John Rice Irwin Harvey Kite Charlie Manning Alice...

  15. Blake Case | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Blake Case Larry Case Patrick Case Dorothy Coker Gordon Fee Linda Fellers Louis Freels Marie Guy Nathan Henry Agnes Houser John Rice Irwin Harvey Kite Charlie Manning Alice...

  16. Water Efficiency Case Studies | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Water Efficiency Case Studies Water Efficiency Case Studies These case studies offer examples of water efficiency projects implemented by federal agencies. They are organized by ...

  17. BBRN Factsheet: Case Study: Community Engagement | Department...

    Office of Environmental Management (EM)

    BBRN Factsheet: Case Study: Community Engagement BBRN Factsheet: Case Study: Community Engagement Case Study: Community Engagement, on the Community Home Energy Retrofit Project...

  18. Non-ferromagnetic overburden casing

    DOE Patents [OSTI]

    Vinegar, Harold J. (Bellaire, TX); Harris, Christopher Kelvin (Houston, TX); Mason, Stanley Leroy (Allen, TX)

    2010-09-14

    Systems, methods, and heaters for treating a subsurface formation are described herein. At least one system for electrically insulating an overburden portion of a heater wellbore is described. The system may include a heater wellbore located in a subsurface formation and an electrically insulating casing located in the overburden portion of the heater wellbore. The casing may include at least one non-ferromagnetic material such that ferromagnetic effects are inhibited in the casing.

  19. FAQ for Case Study Authors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reviews » FAQ for Case Study Authors Science Engagement Move your data Programs & Workshops Science Requirements Reviews Network Requirements Reviews Documents and Background Materials FAQ for Case Study Authors BER Requirements Review 2015 ASCR Requirements Review 2015 Previous Reviews Requirements Review Reports Case Studies Contact Us Technical Assistance: 1 800-33-ESnet (Inside US) 1 800-333-7638 (Inside US) 1 510-486-7600 (Globally) 1 510-486-7607 (Globally) Report Network Problems:

  20. FAQ for Case Study Authors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reviews FAQ for Case Study Authors Science Engagement Move your data Programs & Workshops Science Requirements Reviews Network Requirements Reviews Documents and Background...

  1. Comparison of filter with Prairie and European Network data

    SciTech Connect (OSTI)

    Canavan, G.H.

    1997-10-01

    Earlier notes derived a model for the hydrodynamics, ablation, and radiation of meteor impacts at the level needed to infer meteor parameters from observations and extended it to objects that fragment during entry, using models based on related cometary studies. This note completes the comparison of the resulting filter model to European and Prairie Network (EN and PN) data and models of meteor impact. In cases of mutual applicability, US and European models give broadly consistent results. The quantitative analysis of the EN and PN data is best discussed in conjunction with the Russian program of its analysis, because the Russian program has bypassed the large reported photometrically based masses to derive more plausible estimates of sizes, masses, and radiation efficiencies, which are the primary quantities of concern here. This note completes the discussion of the PN and EN data begun earlier, uses the data to produce filter predictions, and compares it with observations and the predictions of the Russian analytic effort. The overall agreement is useful in that the Russian efforts have employed more complex models that use observational data directly, while the filter model is at a level of simplification much better suited to data inversion.

  2. Ukraine-Capacity Building for Low Carbon Growth | Open Energy...

    Open Energy Info (EERE)

    Ukraine-Capacity Building for Low Carbon Growth (Redirected from UNDP-Capacity Building for Low Carbon Growth in Ukraine) Jump to: navigation, search Name UNDP-Capacity Building...

  3. Ukraine-Capacity Building for Low Carbon Growth | Open Energy...

    Open Energy Info (EERE)

    Ukraine-Capacity Building for Low Carbon Growth Jump to: navigation, search Name UNDP-Capacity Building for Low Carbon Growth in Ukraine AgencyCompany Organization United Nations...

  4. ALS Technique Gives Novel View of Lithium Battery Dendrite Growth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ALS Technique Gives Novel View of Lithium Battery Dendrite Growth ALS Technique Gives Novel View of Lithium Battery Dendrite Growth Print Thursday, 24 April 2014 09:46 Lithium-ion...

  5. Global Green Growth Forum (3GF) | Open Energy Information

    Open Energy Info (EERE)

    find new green avenues to growth. Green growth has to be at the core of a sustainable strategy to get us out of the economic crisis. To advance this global agenda, Denmark as well...

  6. Home Performance with ENERGY STAR -- 10 Years of Continued Growth...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    with ENERGY STAR -- 10 Years of Continued Growth Home Performance with ENERGY STAR -- 10 Years of Continued Growth Provides an overview of the HPwES program, HPwES successes, and...

  7. Role of Nucleation and Growth in Two-Phase Microstructure Formation

    SciTech Connect (OSTI)

    Jong Ho Shin

    2008-05-01

    During the directional solidification of peritectic alloys, a rich variety of two-phase microstructures develop, and the selection process of a specific microstructure is complicated due to the following two considerations. (1) In contrast to many single phase and eutectic microstructures that grow under steady state conditions, two-phase microstructures in a peritectic system often evolve under non-steady-state conditions that can lead to oscillatory microstructures, and (2) the microstructure is often governed by both the nucleation and the competitive growth of the two phases in which repeated nucleation can occur due to the change in the local conditions during growth. In this research, experimental studies in the Sn-Cd system were designed to isolate the effects of nucleation and competitive growth on the dynamics of complex microstructure formation. Experiments were carried out in capillary samples to obtain diffusive growth conditions so that the results can be analyzed quantitatively. At high thermal gradient and low velocity, oscillatory microstructures were observed in which repeated nucleation of the two phases was observed at the wall-solid-liquid junction. Quantitative measurements of nucleation undercooling were obtained for both the primary and the peritectic phase nucleation, and three different ampoule materials were used to examine the effect of different contact angles at the wall on nucleation undercooling. Nucleation undercooling for each phase was found to be very small, and the experimental undercooling values were orders of magnitude smaller than that predicted by the classical theory of nucleation. A new nucleation mechanism is proposed in which the clusters of atoms at the wall ahead of the interface can become a critical nucleus when the cluster encounters the triple junction. Once the nucleation of a new phase occurs, the microstructure is found to be controlled by the relative growth of the two phases that give rise to different oscillatory microstructures that depend on the imposed velocity and the size of the sample. At low thermal gradient to velocity ratio, a steady-state composite microstructure is observed. Two mechanisms of composite microstructure formation were examined: (1) the formation of the peritectic phase in the intercellular region of the primary phase where the solute rejected by the primary phase is absorbed by the peritectic phase. The peritectic phase forms a small distance behind the growing primary phase front. (2) The second mechanism is the coupled growth of the two phases with a macroscopically planar interface, as in the case of eutectic growth. Detailed studies showed that this composite microstructure, although it appears as a eutectic microstructure, did not grow in the coupled manner at the advancing interface in the Sn-cd system. However, a new observation was made when experiments were carried out in thin ampoule of Ta. The peritectic phase nucleated at the wall-interface triple junction and grew along the wall, while the primary phase continued to grow at the center, giving rise to a steady-state couple growth at some specific velocity. The mechanism of coupled growth in this case was shown to be operative due to the presence of a finite contact angle at the wall, and this was demonstrated by including the contact angle effect at the wall in the rod eutectic growth model. The experimental results were summarized to map out the conditions of thermal gradient and velocity on the regimes of composite and oscillatory microstructure formation. The formation of complex time-dependent microstructures was then discussed in terms of the time-dependent dynamics of planar interface growth.

  8. Preliminary Study on Emittance Growth in the LHEC Recirculating Linac

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect Preliminary Study on Emittance Growth in the LHEC Recirculating Linac Citation Details In-Document Search Title: Preliminary Study on Emittance Growth in the LHEC Recirculating Linac In this paper, we estimate the emittance growth in the LHeC recirculating Linac, the lattice design of which is presented in another paper of IPAC10 proceedings. The possible sources for emittance growth included here are: energy spread from RF acceleration in the SRF

  9. Alternative Fuels Data Center: Massachusetts Sees Significant Growth in

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Electric Vehicles and Infrastructure Massachusetts Sees Significant Growth in Electric Vehicles and Infrastructure to someone by E-mail Share Alternative Fuels Data Center: Massachusetts Sees Significant Growth in Electric Vehicles and Infrastructure on Facebook Tweet about Alternative Fuels Data Center: Massachusetts Sees Significant Growth in Electric Vehicles and Infrastructure on Twitter Bookmark Alternative Fuels Data Center: Massachusetts Sees Significant Growth in Electric Vehicles

  10. Elizabeth Case | Department of Energy

    Office of Environmental Management (EM)

    Case About Us Elizabeth Case - Guest Blogger, Cycle for Science Most Recent Rain or Shine: We Cycle for Science July 2 Mountains, and Teachers, and a Bear, Oh My! June 2 Sol-Cycle: Biking Across America for Science Education May 1

  11. Business Case for Technical Qualification Program Accreditation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Business Case for Technical Qualification Program Accreditation Incentives Business Case for Technical Qualification Program Accreditation Incentives TQP Accreditation standardize ...

  12. Growth and nonlinearity. Final project report, April 1, 1985--January 1, 1996

    SciTech Connect (OSTI)

    Sander, L.M.; Savit, R.

    1998-05-01

    This research had three major themes: Fractal growth, pattern formation and the analysis of complexity; that is, the effects of random processes in creating hidden order in statistical system, the interplay between this hidden order and macroscopic order, and the analysis of these complex systems. For example, a dendritic crystal such as a snowflake has a complicated and beautiful pattern with much evidence of the underlying six-fold symmetry of ice. It is a pattern forming system. However, in a disordered environment (such as growth on a rough or dirty surface) this order is replaced by a new order, the fractal or scaling symmetry of a disordered crystal. In this case every part of the crystal is similar on the average to the whole (up to a change in scale). The description of these new kinds of order may require the introduction of new analytic and numerical methods.

  13. Rooftop Unit Comparison Calculator User Manual

    SciTech Connect (OSTI)

    Miller, James D.

    2015-04-30

    This document serves as a user manual for the Packaged rooftop air conditioners and heat pump units comparison calculator (RTUCC) and is an aggregation of the calculator’s website documentation. Content ranges from new-user guide material like the “Quick Start” to the more technical/algorithmic descriptions of the “Methods Pages.” There is also a section listing all the context-help topics that support the features on the “Controls” page. The appendix has a discussion of the EnergyPlus runs that supported the development of the building-response models.

  14. Material requirements for the adoption of unconventional silicon crystal and wafer growth techniques for high-efficiency solar cells

    SciTech Connect (OSTI)

    Hofstetter, Jasmin; del Caizo, Carlos; Wagner, Hannes; Castellanos, Sergio; Buonassisi, Tonio

    2015-10-15

    Silicon wafers comprise approximately 40% of crystalline silicon module cost and represent an area of great technological innovation potential. Paradoxically, unconventional wafer-growth techniques have thus far failed to displace multicrystalline and Czochralski silicon, despite four decades of innovation. One of the shortcomings of most unconventional materials has been a persistent carrier lifetime deficit in comparison to established wafer technologies, which limits the device efficiency potential. In this perspective article, we review a defect-management framework that has proven successful in enabling millisecond lifetimes in kerfless and cast materials. Control of dislocations and slowly diffusing metal point defects during growth, coupled to effective control of fast-diffusing species during cell processing, is critical to enable high cell efficiencies. As a result, to accelerate the pace of novel wafer development, we discuss approaches to rapidly evaluate the device efficiency potential of unconventional wafers from injection-dependent lifetime measurements.

  15. Material requirements for the adoption of unconventional silicon crystal and wafer growth techniques for high-efficiency solar cells

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Hofstetter, Jasmin; del Cañizo, Carlos; Wagner, Hannes; Castellanos, Sergio; Buonassisi, Tonio

    2015-10-15

    Silicon wafers comprise approximately 40% of crystalline silicon module cost and represent an area of great technological innovation potential. Paradoxically, unconventional wafer-growth techniques have thus far failed to displace multicrystalline and Czochralski silicon, despite four decades of innovation. One of the shortcomings of most unconventional materials has been a persistent carrier lifetime deficit in comparison to established wafer technologies, which limits the device efficiency potential. In this perspective article, we review a defect-management framework that has proven successful in enabling millisecond lifetimes in kerfless and cast materials. Control of dislocations and slowly diffusing metal point defects during growth, coupled tomore » effective control of fast-diffusing species during cell processing, is critical to enable high cell efficiencies. As a result, to accelerate the pace of novel wafer development, we discuss approaches to rapidly evaluate the device efficiency potential of unconventional wafers from injection-dependent lifetime measurements.« less

  16. Analysis of Restricted Natural Gas Supply Cases

    Reports and Publications (EIA)

    2004-01-01

    The four cases examined in this study have progressively greater impacts on overall natural gas consumption, prices, and supply. Compared to the Annual Energy Outlook 2004 reference case, the no Alaska pipeline case has the least impact; the low liquefied natural gas case has more impact; the low unconventional gas recovery case has even more impact; and the combined case has the most impact.

  17. Growth histories in bimetric massive gravity

    SciTech Connect (OSTI)

    Berg, Marcus; Buchberger, Igor; Enander, Jonas; Mrtsell, Edvard; Sjrs, Stefan E-mail: igor.buchberger@kau.se E-mail: edvard@fysik.su.se

    2012-12-01

    We perform cosmological perturbation theory in Hassan-Rosen bimetric gravity for general homogeneous and isotropic backgrounds. In the de Sitter approximation, we obtain decoupled sets of massless and massive scalar gravitational fluctuations. Matter perturbations then evolve like in Einstein gravity. We perturb the future de Sitter regime by the ratio of matter to dark energy, producing quasi-de Sitter space. In this more general setting the massive and massless fluctuations mix. We argue that in the quasi-de Sitter regime, the growth of structure in bimetric gravity differs from that of Einstein gravity.

  18. Crystal growth under external electric fields

    SciTech Connect (OSTI)

    Uda, Satoshi; Koizumi, Haruhiko; Nozawa, Jun; Fujiwara, Kozo

    2014-10-06

    This is a review article concerning the crystal growth under external electric fields that has been studied in our lab for the past 10 years. An external field is applied electrostatically either through an electrically insulating phase or a direct injection of an electric current to the solid-interface-liquid. The former changes the chemical potential of both solid and liquid and controls the phase relationship while the latter modifies the transport and partitioning of ionic solutes in the oxide melt during crystallization and changes the solute distribution in the crystal.

  19. Construction Cost Growth for New Department of Energy Nuclear Facilities

    SciTech Connect (OSTI)

    Kubic, Jr., William L.

    2014-05-25

    Cost growth and construction delays are problems that plague many large construction projects including the construction of new Department of Energy (DOE) nuclear facilities. A study was conducted to evaluate cost growth of large DOE construction projects. The purpose of the study was to compile relevant data, consider the possible causes of cost growth, and recommend measures that could be used to avoid extreme cost growth in the future. Both large DOE and non-DOE construction projects were considered in this study. With the exception of Chemical and Metallurgical Research Building Replacement Project (CMRR) and the Mixed Oxide Fuel Fabrication Facility (MFFF), cost growth for DOE Nuclear facilities is comparable to the growth experienced in other mega construction projects. The largest increase in estimated cost was found to occur between early cost estimates and establishing the project baseline during detailed design. Once the project baseline was established, cost growth for DOE nuclear facilities was modest compared to non-DOE mega projects.

  20. Ice Concentration Retrieval in Stratiform Mixed-phase Clouds Using Cloud Radar Reflectivity Measurements and 1D Ice Growth Model Simulations

    SciTech Connect (OSTI)

    Zhang, Damao; Wang, Zhien; Heymsfield, Andrew J.; Fan, Jiwen; Luo, Tao

    2014-10-01

    Measurement of ice number concentration in clouds is important but still challenging. Stratiform mixed-phase clouds (SMCs) provide a simple scenario for retrieving ice number concentration from remote sensing measurements. The simple ice generation and growth pattern in SMCs offers opportunities to use cloud radar reflectivity (Ze) measurements and other cloud properties to infer ice number concentration quantitatively. To understand the strong temperature dependency of ice habit and growth rate quantitatively, we develop a 1-D ice growth model to calculate the ice diffusional growth along its falling trajectory in SMCs. The radar reflectivity and fall velocity profiles of ice crystals calculated from the 1-D ice growth model are evaluated with the Atmospheric Radiation Measurements (ARM) Climate Research Facility (ACRF) ground-based high vertical resolution radar measurements. Combining Ze measurements and 1-D ice growth model simulations, we develop a method to retrieve the ice number concentrations in SMCs at given cloud top temperature (CTT) and liquid water path (LWP). The retrieved ice concentrations in SMCs are evaluated with in situ measurements and with a three-dimensional cloud-resolving model simulation with a bin microphysical scheme. These comparisons show that the retrieved ice number concentrations are within an uncertainty of a factor of 2, statistically.

  1. Generic Argillite/Shale Disposal Reference Case

    SciTech Connect (OSTI)

    Zheng, Liange; Colon, Carlos Jov; Bianchi, Marco; Birkholzer, Jens

    2014-08-08

    Radioactive waste disposal in a deep subsurface repository hosted in clay/shale/argillite is a subject of widespread interest given the desirable isolation properties, geochemically reduced conditions, and widespread geologic occurrence of this rock type (Hansen 2010; Bianchi et al. 2013). Bianchi et al. (2013) provides a description of diffusion in a clay-hosted repository based on single-phase flow and full saturation using parametric data from documented studies in Europe (e.g., ANDRA 2005). The predominance of diffusive transport and sorption phenomena in this clay media are key attributes to impede radionuclide mobility making clay rock formations target sites for disposal of high-level radioactive waste. The reports by Hansen et al. (2010) and those from numerous studies in clay-hosted underground research laboratories (URLs) in Belgium, France and Switzerland outline the extensive scientific knowledge obtained to assess long-term clay/shale/argillite repository isolation performance of nuclear waste. In the past several years under the UFDC, various kinds of models have been developed for argillite repository to demonstrate the model capability, understand the spatial and temporal alteration of the repository, and evaluate different scenarios. These models include the coupled Thermal-Hydrological-Mechanical (THM) and Thermal-Hydrological-Mechanical-Chemical (THMC) models (e.g. Liu et al. 2013; Rutqvist et al. 2014a, Zheng et al. 2014a) that focus on THMC processes in the Engineered Barrier System (EBS) bentonite and argillite host hock, the large scale hydrogeologic model (Bianchi et al. 2014) that investigates the hydraulic connection between an emplacement drift and surrounding hydrogeological units, and Disposal Systems Evaluation Framework (DSEF) models (Greenberg et al. 2013) that evaluate thermal evolution in the host rock approximated as a thermal conduction process to facilitate the analysis of design options. However, the assumptions and the properties (parameters) used in these models are different, which not only make inter-model comparisons difficult, but also compromise the applicability of the lessons learned from one model to another model. The establishment of a reference case would therefore be helpful to set up a baseline for model development. A generic salt repository reference case was developed in Freeze et al. (2013) and the generic argillite repository reference case is presented in this report. The definition of a reference case requires the characterization of the waste inventory, waste form, waste package, repository layout, EBS backfill, host rock, and biosphere. This report mainly documents the processes in EBS bentonite and host rock that are potentially important for performance assessment and properties that are needed to describe these processes, with brief description other components such as waste inventory, waste form, waste package, repository layout, aquifer, and biosphere. A thorough description of the generic argillite repository reference case will be given in Jov Colon et al. (2014).

  2. Thermal stability comparison of nanocrystalline Fe-based binary alloy pairs

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Clark, Blythe G.; Hattar, Khalid Mikhiel; Marshall, Michael Thomas; Chookajorn, Tonghai; Boyce, Brad L.; Schuh, Christopher A.

    2016-03-24

    Here, the widely recognized property improvements of nanocrystalline (NC) materials have generated significant interest, yet have been difficult to realize in engineering applications due to the propensity for grain growth in these interface-dense systems. While traditional pathways to thermal stabilization can slow the mobility of grain boundaries, recent theories suggest that solute segregation in NC alloy can reduce the grain boundary energy such that thermodynamic stabilization is achieved. Following the predictions of Murdock et al., here we compare for the first time the thermal stability of a predicted NC stable alloy (Fe-10at.% Mg) with a predicted non-NC stable alloy (Fe-10at.%more » Cu) using the same processing and characterization methodologies. Results indicate improved thermal stability of the Fe-Mg alloy in comparison to the Fe-Cu, and observed microstructures are consistent with those predicted by Monte Carlo simulations.« less

  3. Comparison of Fuel Cell Technologies | Department of Energy

    Office of Environmental Management (EM)

    Comparison of Fuel Cell Technologies Comparison of Fuel Cell Technologies Each fuel cell technology has advantages and disadvantages. See how fuel cell technologies compare with one another. This comparison chart is also available as a fact sheet. Fuel Cell Type Common Electrolyte Operating Temperature Typical Stack Size Electrical Efficiency (LHV) Applications Advantages Disadvantages Polymer Electrolyte Membrane (PEM) Perfluorosulfonic acid <120°C <1 kW-100 kW 60% direct H2;a 40%

  4. Precision growth index using the clustering of cosmic structures and growth data

    SciTech Connect (OSTI)

    Pouri, Athina; Basilakos, Spyros; Plionis, Manolis E-mail: svasil@academyofathens.gr

    2014-08-01

    We use the clustering properties of Luminous Red Galaxies (LRGs) and the growth rate data provided by the various galaxy surveys in order to constrain the growth index ?) of the linear matter fluctuations. We perform a standard ?{sup 2}-minimization procedure between theoretical expectations and data, followed by a joint likelihood analysis and we find a value of ?=0.560.05, perfectly consistent with the expectations of the ?CDM model, and ?{sub m0}=0.290.01, in very good agreement with the latest Planck results. Our analysis provides significantly more stringent growth index constraints with respect to previous studies, as indicated by the fact that the corresponding uncertainty is only ?0.09?. Finally, allowing ? to vary with redshift in two manners (Taylor expansion around z=0, and Taylor expansion around the scale factor), we find that the combined statistical analysis between our clustering and literature growth data alleviates the degeneracy and obtain more stringent constraints with respect to other recent studies.

  5. OHA Whistleblower Cases Archive File

    Broader source: Energy.gov [DOE]

    This is a archive file of our Whistleblower decisions, Please download this file to your local computer and use the build in adobe search feature. Individual cases are listed in the bookmark...

  6. OHA Security Cases Archive File

    Broader source: Energy.gov [DOE]

    This is a archive file of our Security decisions, Please download this file to your local computer and use the build in adobe search feature. Individual cases are listed in the bookmark section of...

  7. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    by region and country, Low Oil Price case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030...

  8. Alternative Fuels Data Center: Case Studies

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Case Studies Printable Version Share this resource Send a link to Alternative Fuels Data Center: Case Studies to someone by E-mail Share Alternative Fuels Data Center: Case Studies on Facebook Tweet about Alternative Fuels Data Center: Case Studies on Twitter Bookmark Alternative Fuels Data Center: Case Studies on Google Bookmark Alternative Fuels Data Center: Case Studies on Delicious Rank Alternative Fuels Data Center: Case Studies on Digg Find More places to share Alternative Fuels Data

  9. 1999 Commercial Building Characteristics--Building Activity Comparison

    U.S. Energy Information Administration (EIA) Indexed Site

    Building Activity Comparison Percentage of Floorspace and Buildings by Principal Building Activity, 1999 Percentage of Floorspace and Buildings by Principal Building Activity,...

  10. 1999 Commercial Building Characteristics--Year Constructed Comparison

    U.S. Energy Information Administration (EIA) Indexed Site

    Year Constructed Comparison Percentage of Floorspace and Buildings by Year Constructed, 1999 Percentage of Floorspace and Buildings by Year Constructed, 1999. If having trouble...

  11. Energy Conservation Program: Data Collection and Comparison with...

    Energy Savers [EERE]

    Energy Conservation Program: Data Collection and Comparison with Forecasted Unit Sales for Five Lamp Types, Notice of Data Availability Energy Conservation Program: Data Collection ...

  12. Energy Conservation Program: Data Collection and Comparison with...

    Energy Savers [EERE]

    EERE-2011-BT-NOA-0013 Energy Conservation Program: Data Collection and Comparison with Forecasted Unit Sales of Five Lamp Types AGENCY: Office of Energy Efficiency and Renewable ...

  13. Life-Cycle Analysis Results of Geothermal Systems in Comparison...

    Office of Environmental Management (EM)

    Systems in Comparison to Other Power Systems A life-cycle energy and greenhouse gas emissions analysis has been conducted with Argonne National Laboratory's GREET model...

  14. Discussion on a Code Comparison Effort for the Geothermal Technologies...

    Office of Environmental Management (EM)

    Technologies Program Code comparison presentation by Mark White of PNNL at the 2012 Peer Review meeting on May 10. PDF icon gtp2012peerreviewpnnlwhite.pdf More Documents &...

  15. Comparison of Software Models for Energy Savings from Cool Roofs...

    Office of Scientific and Technical Information (OSTI)

    RSC results reduce cool roofing cost-effectiveness thus mitigating expected economic ... Comparison to previous simulation-based studies, analysis on the force multiplier of RSC ...

  16. Experimental and Statistical Comparison of Engine Response as...

    Office of Scientific and Technical Information (OSTI)

    Experimental and Statistical Comparison of Engine Response as a Function of Fuel Chemistry ... Engine Response as a Function of Fuel Chemistry and Properties in CI and HCCI Engines ...

  17. National and Sectoral GHG Mitigation Potential: A Comparison...

    Open Energy Info (EERE)

    and Sectoral GHG Mitigation Potential: A Comparison Across Models Jump to: navigation, search Tool Summary LAUNCH TOOL Name: National and Sectoral GHG Mitigation Potential: A...

  18. Comparison of Materials for Use in the Precision Grinding of...

    Office of Scientific and Technical Information (OSTI)

    and deterministically fabrication optical surfaces to final or near-final surface finish and figure. In this paper, a comparison of grinding techniques and materials is performed. ...

  19. Comparison of Water-Hydrogen Catalytic Exchange Processes vs...

    Office of Environmental Management (EM)

    at Tritium Focus Group Meeting, April 22-24, 2014, Aiken, SC COMPARISON OF WATER-HYDROGEN CATALYTIC EXCHANGE PROCESSES VERSUS WATER DISTILLATION FOR WATER DETRITIATION A. Busigin,...

  20. A Comparison of Cirrus Cloud Visible Optical Depth Derived from...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Comparison of Cirrus Cloud Visible Optical Depth Derived from Lidar Lo, Chaomei Pacific Northwest National Laboratory Comstock, Jennifer Pacific Northwest National Laboratory...

  1. Comparison of Different Load Road Implementation Strategies on...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Different Load Road Implementation Strategies on Fuel Economy of USPS Step Vans Comparison of Different Load Road Implementation Strategies on Fuel Economy of USPS Step Vans An ...

  2. Distributed Wind Policy Comparison Tool | Open Energy Information

    Open Energy Info (EERE)

    URI: cleanenergysolutions.orgcontentdistributed-wind-policy-comparison-to Language: English Policies: "Deployment Programs,Financial Incentives,Regulations" is not in...

  3. Ch. IV, A hydrogeochemical comparison of the Waunita Hot Springs...

    Open Energy Info (EERE)

    A hydrogeochemical comparison of the Waunita Hot Springs, Hortense, Castle Rock and Anderson Hot Springs Jump to: navigation, search OpenEI Reference LibraryAdd to library...

  4. A Comparison of Alternating Direction Swept Remap and Intersection...

    Office of Scientific and Technical Information (OSTI)

    Title: A Comparison of Alternating Direction Swept Remap and Intersection Remap in the X-FEM Alegra Code. Abstract not provided. Authors: Mosso, Stewart John ; Kramer, Richard ...

  5. BerkeleyGW Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    BerkeleyGW Case Study BerkeleyGW Case Study Code Description and Science Problem BerkeleyGW is a Materials Science application for calculating the excited state properties of materials such as band gaps, band structures, absoprtion spectroscopy, photoemission spectroscopy and more. It requires as input the Kohn-Sham orbitals and energies from a DFT code like Quantum ESPRESSO, PARATEC, PARSEC etc. Like such DFT codes, it is heavily depedent on FFTs, Dense Linear algebra and tensor contraction

  6. Chombo-Crunch Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Chombo-Crunch Case Study Chombo-Crunch Case Study Background Chombo-Crunch is a high-performance software package which has been developed jointly by research scientists from Applied Numerical Algorithms Group, Computational Research Division (PI: David Trebotich) and Earth Sciences Division at LBNL for large-scale numerical simulations of complex fluid flows with particular interest in modeling of subsurface flows. One important application example of subsurface flow is a carbon sequestration -

  7. EIA Cases | Department of Energy

    Energy Savers [EERE]

    EIA Cases EIA Cases RSS February 14, 2011 TEE-0073 - In the Matter of Cole Distributing, Inc. On December 13, 2010, Cole Distributing, Inc. (Cole) filed an Application for Exception with the Office of Hearings and Appeals (OHA) of the Department of Energy (DOE). The firm requests that it be permanently relieved of the requirement to prepare and file the Energy Information Administration (EIA) Form EIA-782B, entitled "Resellers'/Retailers' Monthly Petroleum Product Sales Report." As

  8. FOIA Cases | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    FOIA Cases FOIA Cases RSS December 22, 2015 FIA-15-0066 - In the Matter of Government Accountability Project On December 22, 2015, OHA denied a FOIA Appeal filed by Government Accountability Project from a determination issued by the DOE Office of Inspector General (OIG). In the Appeal, the Appellant challenged the redactions made in the responsive documents. OHA found, however, that the redactions made pursuant FOIA Exemptions 5 and 6 were appropriate. December 10, 2015 FIA-15-0064 - In the

  9. Whistleblower Cases | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Whistleblower Cases Whistleblower Cases RSS December 31, 2015 WBA-15-0009 - In the Matter of Sandra Black On December 31, 2015, OHA denied an Appeal involving a Complaint filed by Sandra Black against Savannah River Nuclear Solutions, LLC (SRNS) under the DOE's Contractor Employee Protection Program, 10 CFR Part 708. In her Complaint, Black alleged SRNS terminated her for engaging in protected activities, specifically citing her participation in a Government Accountability Office review as a

  10. Security Cases | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Security Cases Security Cases RSS December 22, 2015 PSH-15-0067 - In the Matter of Personnel Security Hearing On December 22, 2015, an Administrative Judge issued a decision in which she determined that an individual's access authorization should not be restored. During a personnel security interview in April 2014 and a credit report review, the Local Security Office (LSO) learned that the individual had a number of charge-off accounts totaling $14,941, as well as an outstanding collection

  11. U.S. Energy Information Administration (EIA) - Pub

    Gasoline and Diesel Fuel Update (EIA)

    Appendices Appendix A Reference case tables Appendix B Economic growth cases comparisons tables Appendix C Price case comparisons tables Appendix D High oil and gas resource case comparisons tables Appendix E Comparison of AEO2015 and AEO2014 Reference cases Appendix F: Regional Maps United States Census Divisions Electricity Market Module Regions Liquid Fuels Market Module Regions Oil and Gas Supply Model Regions Natural Gas Transmission and Distribution Model Regions Coal Supply Regions Coal

  12. Lid for improved dendritic web growth

    DOE Patents [OSTI]

    Duncan, Charles S.; Kochka, Edgar L.; Piotrowski, Paul A.; Seidensticker, Raymond G.

    1992-03-24

    A lid for a susceptor in which a crystalline material is melted by induction heating to form a pool or melt of molten material from which a dendritic web of essentially a single crystal of the material is pulled through an elongated slot in the lid and the lid has a pair of generally round openings adjacent the ends of the slot and a groove extends between each opening and the end of the slot. The grooves extend from the outboard surface of the lid to adjacent the inboard surface providing a strip contiguous with the inboard surface of the lid to produce generally uniform radiational heat loss across the width of the dendritic web adjacent the inboard surface of the lid to reduce thermal stresses in the web and facilitate the growth of wider webs at a greater withdrawal rate.

  13. Cadmium zinc sulfide by solution growth

    DOE Patents [OSTI]

    Chen, Wen S.

    1992-05-12

    A process for depositing thin layers of a II-VI compound cadmium zinc sulfide (CdZnS) by an aqueous solution growth technique with quality suitable for high efficiency photovoltaic or other devices which can benefit from the band edge shift resulting from the inclusion of Zn in the sulfide. A first solution comprising CdCl.sub.2 2.5H.sub.2 O, NH.sub.4 Cl, NH.sub.4 OH and ZnCl.sub.2, and a second solution comprising thiourea ((NH.sub.2).sub.2 CS) are combined and placed in a deposition cell, along with a substrate to form a thin i.e. 10 nm film of CdZnS on the substrate. This process can be sequentially repeated with to achieve deposition of independent multiple layers having different Zn concentrations.

  14. Long-term control of root growth

    DOE Patents [OSTI]

    Burton, Frederick G. (West Richland, WA); Cataldo, Dominic A. (Kennewick, WA); Cline, John F. (Prosser, WA); Skiens, W. Eugene (Richland, WA)

    1992-05-26

    A method and system for long-term control of root growth without killing the plants bearing those roots involves incorporating a 2,6-dinitroaniline in a polymer and disposing the polymer in an area in which root control is desired. This results in controlled release of the substituted aniline herbicide over a period of many years. Herbicides of this class have the property of preventing root elongation without translocating into other parts of the plant. The herbicide may be encapsulated in the polymer or mixed with it. The polymer-herbicide mixture may be formed into pellets, sheets, pipe gaskets, pipes for carrying water, or various other forms. The invention may be applied to other protection of buried hazardous wastes, protection of underground pipes, prevention of root intrusion beneath slabs, the dwarfing of trees or shrubs and other applications. The preferred herbicide is 4-difluoromethyl-N,N-dipropyl-2,6-dinitro-aniline, commonly known as trifluralin.

  15. Insights from Human/Mouse genome comparisons

    SciTech Connect (OSTI)

    Pennacchio, Len A.

    2003-03-30

    Large-scale public genomic sequencing efforts have provided a wealth of vertebrate sequence data poised to provide insights into mammalian biology. These include deep genomic sequence coverage of human, mouse, rat, zebrafish, and two pufferfish (Fugu rubripes and Tetraodon nigroviridis) (Aparicio et al. 2002; Lander et al. 2001; Venter et al. 2001; Waterston et al. 2002). In addition, a high-priority has been placed on determining the genomic sequence of chimpanzee, dog, cow, frog, and chicken (Boguski 2002). While only recently available, whole genome sequence data have provided the unique opportunity to globally compare complete genome contents. Furthermore, the shared evolutionary ancestry of vertebrate species has allowed the development of comparative genomic approaches to identify ancient conserved sequences with functionality. Accordingly, this review focuses on the initial comparison of available mammalian genomes and describes various insights derived from such analysis.

  16. Comparison of Module Performance Characterization Methods

    SciTech Connect (OSTI)

    KROPOSKI,B.; MARION,W.; KING,DAVID L.; BOYSON,WILLIAM EARL; KRATOCHVIL,JAY A.

    2000-10-03

    The rating and modeling of photovoltaic PW module performance has been of concern to manufacturers and system designers for over 20 years. Both the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories (SNL) have developed methodologies to predict module and array performance under actual operating conditions. This paper compares the two methods of determining the performance of PV modules, The methods translate module performance to actual or reference conditions using slightly different approaches. The accuracy of both methods is compared for both hourly, daily, and annual energy production over a year of data recorded at NREL in Golden, CO. The comparison of the two methods will be presented for five different PV module technologies.

  17. Abnormal grain growth in AISI 304L stainless steel

    SciTech Connect (OSTI)

    Shirdel, M.; Mirzadeh, H.; Parsa, M.H.

    2014-11-15

    The microstructural evolution during abnormal grain growth (secondary recrystallization) in 304L stainless steel was studied in a wide range of annealing temperatures and times. At relatively low temperatures, the grain growth mode was identified as normal. However, at homologous temperatures between 0.65 (850 C) and 0.7 (900 C), the observed transition in grain growth mode from normal to abnormal, which was also evident from the bimodality in grain size distribution histograms, was detected to be caused by the dissolution/coarsening of carbides. The microstructural features such as dispersed carbides were characterized by optical metallography, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, and microhardness. Continued annealing to a long time led to the completion of secondary recrystallization and the subsequent reappearance of normal growth mode. Another instance of abnormal grain growth was observed at homologous temperatures higher than 0.8, which may be attributed to the grain boundary faceting/defaceting phenomenon. It was also found that when the size of abnormal grains reached a critical value, their size will not change too much and the grain growth behavior becomes practically stagnant. - Highlights: Abnormal grain growth (secondary recrystallization) in AISI 304L stainless steel Exaggerated grain growth due to dissolution/coarsening of carbides The enrichment of carbide particles by titanium Abnormal grain growth due to grain boundary faceting at very high temperatures The stagnancy of abnormal grain growth by annealing beyond a critical time.

  18. Case studies of energy efficiency financing in the original five pilot states, 1993-1996

    SciTech Connect (OSTI)

    Farhar, B.C.; Collins, N.E.; Walsh, R.W.

    1997-05-01

    The purpose of this report is to document progress in state-level programs in energy efficiency financing programs that are linked with home energy rating systems. Case studies are presented of programs in five states using a federal pilot program to amortize the costs of home energy improvements. The case studies present background information, describe the states` program, list preliminary evaluation data and findings, and discuss problems and solution encountered in the programs. A comparison of experiences in pilot states will be used to provide guidelines for program implementers, federal agencies, and Congress. 5 refs.

  19. Faster plant growth in a safe, economical way

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Faster plant growth in a safe, economical way Faster plant growth in a safe, economical way When applied to plants, Take-Off(tm) speeds crop emergence, increases growth rates and yields, improves stress tolerance and nutrient value, and reduces need for nitrogen fertilizers. April 3, 2012 Farmer in wheat field inspecting wheat Biagro Western offers Take-Off(tm), a metabolic plant stimulant that will allow farmers to increase crop carbon fixation and thereby increase nitrate uptake and nitrogen

  20. ARM - Lesson Plans: Plant Growth and Carbon Dioxide

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Plant Growth and Carbon Dioxide Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About ARM Global Warming FAQ Just for Fun Meet our Friends Cool Sites Teachers Teachers' Toolbox Lesson Plans Lesson Plans: Plant Growth and Carbon Dioxide Objective The objective is to show how carbon dioxide in the air affects plant growth. Materials Each group of students will need the following: Graph paper Pencil

  1. Before the Subcommittee on Economic Growth, Job Creation and Regulatory

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Affairs - House Committee on Oversight and Governmant Reform | Department of Energy Economic Growth, Job Creation and Regulatory Affairs - House Committee on Oversight and Governmant Reform Before the Subcommittee on Economic Growth, Job Creation and Regulatory Affairs - House Committee on Oversight and Governmant Reform Written statement of Nicholas Whitcombe, Former Acting Director, Advanced Technology Vehicles Manufacturing Loan Program Submitted to the Subcommittee on Economic Growth,

  2. Laboratory Evidence for Stochastic Plasma-Wave Growth

    SciTech Connect (OSTI)

    Austin, D. R.; Hole, M. J.; Robinson, P. A.; Cairns, Iver H.; Dallaqua, R.

    2007-11-16

    The first laboratory confirmation of stochastic growth theory is reported. Floating potential fluctuations are measured in a vacuum arc centrifuge using a Langmuir probe. Statistical analysis of the energy density reveals a lognormal distribution over roughly 2 orders of magnitude, with a high-field nonlinear cutoff whose spatial dependence is consistent with the predicted eigenmode profile. These results are consistent with stochastic growth and nonlinear saturation of a spatially extended eigenmode, the first evidence for stochastic growth of an extended structure.

  3. Fuel Cycle Analysis Framework Base Cases for the IAEA/INPRO GAINS Collaborative Project

    SciTech Connect (OSTI)

    Brent Dixon

    2012-09-01

    Thirteen countries participated in the Collaborative Project GAINS Global Architecture of Innovative Nuclear Energy Systems Based on Thermal and Fast Reactors Including a Closed Fuel Cycle, which was the primary activity within the IAEA/INPRO Program Area B: Global Vision on Sustainable Nuclear Energy for the last three years. The overall objective of GAINS was to develop a standard framework for assessing future nuclear energy systems taking into account sustainable development, and to validate results through sample analyses. This paper details the eight scenarios that constitute the GAINS framework base cases for analysis of the transition to future innovative nuclear energy systems. The framework base cases provide a reference for users of the framework to start from in developing and assessing their own alternate systems. Each base case is described along with performance results against the GAINS sustainability evaluation metrics. The eight cases include four using a moderate growth projection and four using a high growth projection for global nuclear electricity generation through 2100. The cases are divided into two sets, addressing homogeneous and heterogeneous scenarios developed by GAINS to model global fuel cycle strategies. The heterogeneous world scenario considers three separate nuclear groups based on their fuel cycle strategies, with non-synergistic and synergistic cases. The framework base case analyses results show the impact of these different fuel cycle strategies while providing references for future users of the GAINS framework. A large number of scenario alterations are possible and can be used to assess different strategies, different technologies, and different assumptions about possible futures of nuclear power. Results can be compared to the framework base cases to assess where these alternate cases perform differently versus the sustainability indicators.

  4. Y-12 and the Jack Case Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    February 21, 2014, Patrick Case, Jack Case's youngest son, called me. He was at the New Hope Center and wanted to visit the Jack Case Center. I explained that it would have to wait...

  5. Technology Deployment Case Studies | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technology Deployment Case Studies Technology Deployment Case Studies Technology Deployment Case Studies Find efficient technologies and products for federal applications on the Federal Energy Management Program website. View All Maps Addthis

  6. WEF-Green Growth Partnerships Initiative | Open Energy Information

    Open Energy Info (EERE)

    World Economic Forum Partner Global Green Growth Institute, Climate and Development Knowledge Network (CDKN), United Kingdom Government Sector Energy, Land, Climate Topics...

  7. Growth of epitaxial films of sodium potassium tantalate and niobate...

    Office of Scientific and Technical Information (OSTI)

    Growth of epitaxial films of sodium potassium tantalate and niobate on single-crystal ... John Z 2 ; Xue, Ziling 1 ; Beach, David B 2 + Show Author Affiliations ...

  8. Low Carbon Growth Plans: A Sectoral Approach to Climate Protection...

    Open Energy Info (EERE)

    to Climate Protection Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Low Carbon Growth Plans: A Sectoral Approach to Climate Protection AgencyCompany Organization:...

  9. Low Carbon Growth Country Studies Program | Open Energy Information

    Open Energy Info (EERE)

    Country Studies Program Jump to: navigation, search Name Low Carbon Growth Country Studies Program AgencyCompany Organization Energy Sector Management Assistance Program of the...

  10. Low-temperature plasma-deposited silicon epitaxial films: Growth...

    Office of Scientific and Technical Information (OSTI)

    Low-temperature plasma-deposited silicon epitaxial films: Growth and properties Citation Details In-Document Search Title: Low-temperature plasma-deposited silicon epitaxial films:...

  11. Green Growth Best Practice Initiative (GGBPI) | Open Energy Informatio...

    Open Energy Info (EERE)

    (ICI) of the German Federal Ministry of Environment, Nature, Conservation, and Nuclear Safety, European Climate Foundation (ECF), Global Green Growth Institute (GGGI),...

  12. Recent Trends in Car Usage in Advanced Economies - Slower Growth...

    Open Energy Info (EERE)

    Trends in Car Usage in Advanced Economies - Slower Growth Ahead? Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Recent Trends in Car Usage in Advanced Economies -...

  13. Develop low emissions growth scenarios | Open Energy Information

    Open Energy Info (EERE)

    low emissions growth scenarios Jump to: navigation, search Stage 3 LEDS Home Introduction to Framework Assess current country plans, policies, practices, and capacities...

  14. Catalyzing Low Carbon Growth in Developing Countries | Open Energy...

    Open Energy Info (EERE)

    Growth in Developing Countries: Public Finance Mechanisms to scale up private sector investment in climate solutions AgencyCompany Organization: United Nations Environment...

  15. Stress evolution during growth in direct-current-sputtered zinc...

    Office of Scientific and Technical Information (OSTI)

    zinc oxide films at various oxygen flows Citation Details In-Document Search Title: Stress evolution during growth in direct-current-sputtered zinc oxide films at ...

  16. Suppression of Grain Boundaries in Graphene Growth on Superstructured...

    Office of Scientific and Technical Information (OSTI)

    Title: Suppression of Grain Boundaries in Graphene Growth on Superstructured Mn-Cu(111) Surface Authors: Chen, Wei ; Chen, Hua ; Lan, Haiping ; Cui, Ping ; Schulze, Tim P. ; Zhu, ...

  17. Amplified Demand for Solar Trackers to Boost Market Growth in...

    Open Energy Info (EERE)

    Amplified Demand for Solar Trackers to Boost Market Growth in Middle East and Africa Home > Groups > Solar Permitting Roadmap Development Wayne31jan's picture Submitted by...

  18. TianDi Growth Capital | Open Energy Information

    Open Energy Info (EERE)

    Venture capital investor interested in projects in Wind energy, Electric vehicles, Energy-efficient lighting, Biodiesel and Clean water. References: TianDi Growth Capital1...

  19. Fatigue crack growth behavior of Ti-1100 at elevated temperature

    SciTech Connect (OSTI)

    Maxwell, D.C.; Nicholas, T.

    1995-12-31

    Effects of temperature, frequency, and cycles with superimposed hold times are evaluated in Ti-1100 in order to study the complex creep-fatigue-environment interactions in this material. Crack growth rate tests conducted at cyclic loading frequency of 1.0 Hz show that raising the temperature from 593 to 650 C has only a slightly detrimental effect on crack growth rate, although these temperatures produce growth rates significantly higher than at room temperature. From constant {Delta}K tests, the effects of temperature at constant frequency show a minimum crack growth rate at 250 C. From the minimum crack growth rate at 250 C, the crack growth rate increases linearly with temperature. Increases in frequency at constant temperatures of 593 and 650 C produce a continuous decrease in growth rate in going from 0.001 to 1.0 Hz, although the behavior is primarily cycle dependent in this region. Tests at 1.0 Hz with superimposed hold times from 1 to 1,000 s are used to evaluate creep-fatigue-environment interactions. Hold times at maximum load are found to initially decrease and then increase the cyclic crack growth rate with increasing duration. This is attributed to crack-tip blunting during short hold times and environmental degradation at long hold times. Hold times at minimum load show no change in growth rates, indicating that there is no net environmental degradation to the bulk material beyond that experienced during the baseline 1 Hz cycling.

  20. Step-by-step growth of complex oxide microstructures (Journal...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Step-by-step growth of complex oxide microstructures Citation Details In-Document Search This content will become publicly available on June 10, 2016 Title:...

  1. Thermodynamic and kinetic control of the lateral Si wire growth

    SciTech Connect (OSTI)

    Dedyulin, Sergey N. Goncharova, Lyudmila V.

    2014-03-24

    Reproducible lateral Si wire growth has been realized on the Si (100) surface. In this paper, we present experimental evidence showing the unique role that carbon plays in initiating lateral growth of Si wires on a Si (100) substrate. Once initiated in the presence of ?5 ML of C, lateral growth can be achieved in the range of temperatures, T?=?450650?C, and further controlled by the interplay of the flux of incoming Si atoms with the size and areal density of Au droplets. Critical thermodynamic and kinetic aspects of the growth are discussed in detail.

  2. Strengthening Planning Capacity for Low Carbon Growth in Developing...

    Open Energy Info (EERE)

    Growth in Developing Asia AgencyCompany Organization Asian Development Bank Partner Japan, United Kingdom Sector Climate, Energy Focus Area Non-renewable Energy, Buildings,...

  3. Philippines-Strengthening Planning Capacity for Low Carbon Growth...

    Open Energy Info (EERE)

    Growth in Developing Asia AgencyCompany Organization Asian Development Bank Partner Japan, United Kingdom Sector Climate, Energy Focus Area Non-renewable Energy, Buildings,...

  4. Indonesia-Strengthening Planning Capacity for Low Carbon Growth...

    Open Energy Info (EERE)

    Growth in Developing Asia AgencyCompany Organization Asian Development Bank Partner Japan, United Kingdom Sector Climate, Energy Focus Area Non-renewable Energy, Buildings,...

  5. Vietnam-Strengthening Planning Capacity for Low Carbon Growth...

    Open Energy Info (EERE)

    Growth in Developing Asia AgencyCompany Organization Asian Development Bank Partner Japan, United Kingdom Sector Climate, Energy Focus Area Non-renewable Energy, Buildings,...

  6. Atomistic mechanisms for bilayer growth of graphene on metal...

    Office of Scientific and Technical Information (OSTI)

    Atomistic mechanisms for bilayer growth of graphene on metal substrates This content will become publicly available on January 8, 2016 Prev Next Title: Atomistic mechanisms...

  7. Green Growth in Motion: Sharing Korea's Experience | Open Energy...

    Open Energy Info (EERE)

    lt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":"" Hide Map Language: English Green Growth in Motion: Sharing Korea's Experience Screenshot References:...

  8. Techniques for Growth of Lattice-Matched Semiconductor Layers...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for Growth of Lattice-Matched Semiconductor Layers For the fabrication of multi-junction solar cells, light emitting diodes, and high speed transistors National Renewable...

  9. Larry Case | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Larry Case Larry Case Oral History Videos Speakers INTRODUCTION Ed Bailey Jim Bailey Kay Bailey Ken Bernander Willard Brock Wilma Brooks Elmer Brummitt Naomi Brummitt Blake Case Larry Case Patrick Case Dorothy Coker Gordon Fee Linda Fellers Louis Freels Marie Guy Nathan Henry Agnes Houser John Rice Irwin Harvey Kite Charlie Manning Alice Piercey Donald Raby Jack Rains Ray Smith Ken Sommerfeld Kay Steed Bill Wilcox Beverly Woods more ... Options Hide Chapters Show Transcript Larry Case Jack

  10. Case Studies by System | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technical Assistance » Case Studies by System Case Studies by System Case studies document the energy savings achieved by large manufacturing companies using AMO's software tools, other technical publications, and best practices. Case studies are available below for the following systems: Steam, Process Heating, Compressed Air, Motor, Pump, Fan, and Plant Wide. Case studies are also available for Combined Heat & Power. Plant-Wide Case Studies Alcoa: C-Suite Participation in Energy

  11. BoxLib Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    BoxLib Case Study BoxLib Case Study Background BoxLib is a publicly available software framework for building massively parallel block-structured AMR applications. Key features of BoxLib include Support for block-structured AMR with optional subcycling in time Support for cell-centered, face-centered and node-centered data Support for hyperbolic, parabolic, and elliptic solves on hierarchical grid structure C++ and Fortran90 versions Support for hybrid parallelism model with MPI and OpenMP Basis

  12. Case Western University | Open Energy Information

    Open Energy Info (EERE)

    University Jump to: navigation, search Name Case Western University Facility Case Western University Sector Wind energy Facility Type Small Scale Wind Facility Status In Service...

  13. Building America Technologies Solutions Case Study: Ventilation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technologies Solutions Case Study: Ventilation System Effectiveness and Tested Indoor Air Quality Impacts Building America Technologies Solutions Case Study: Ventilation System ...

  14. Building America Technology Solutions Case Study: Ventilation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Case Study: Ventilation System Effectiveness and Tested Indoor Air Quality Impacts Building America Technology Solutions Case Study: Ventilation System Effectiveness and Tested ...

  15. Renewable Energy Case Studies | Open Energy Information

    Open Energy Info (EERE)

    Case Studies Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Renewable Energy Case Studies AgencyCompany Organization: National Renewable Energy Laboratory Sector:...

  16. CASE Design/Remodeling | Open Energy Information

    Open Energy Info (EERE)

    DesignRemodeling Jump to: navigation, search Name: CASE DesignRemodeling Place: Bethesda, MD Website: www.casedesignremodeling.com References: CASE DesignRemodeling1...

  17. Susceptor for EFG crystal growth apparatus

    DOE Patents [OSTI]

    Menna, Andrew A. (Belmont, MA)

    1996-09-03

    An improved susceptor for a crucible/die assembly for growing tubular crystalline structures by the EFG process is provided. The crucible/die assembly comprises a die having a substantially polygonally-shaped top end surface for supporting a film of silicon feed material that is replenished from a melt in the crucible through capillary action. A hollow crystalline body is grown from the film of silicon material on the top end surface of the die. The heat susceptor is made of graphite or similar material, and has a peripheral configuration similar to that of the die. Further, the upper surface of the heat susceptor has a central land and a plurality of circumferentially-spaced upwardly extending projections. The central land thermally contacts a central portion of the lower surface of the crucible/die, and the projections thermally contact the lower surface of the crucible/die at its corners, whereby a temperature distribution is provided that permits growth of hollow bodies having more nearly constant thickness walls.

  18. World pipeline work set for rapid growth

    SciTech Connect (OSTI)

    Not Available

    1992-08-01

    This paper reports on international pipeline construction which has entered a fast-growth period, accelerated by the new political and economic realities around the world and increasing demand for natural gas, crude oil and refined petroleum products. Many projects are under way or in planning for completion in the mid- to late 1990s in Europe, South America, Asia and the Middle East. Pipeline And Gas Journal's projection calls for construction or other work on 30,700 miles of new natural gas, crude oil and refined products pipelines in the 1992-93 period outside Canada and the U.S. These projects will cost an estimated $30 billion-plus. Natural gas pipelines will comprise most of the mileage, accounting for almost 23,000 miles at an estimated cost of $26.3 billion. Products pipelines, planned or under construction, will add another 5,800 miles at a cost of $2.8 billion. Crude oil pipelines, at a minimum, will total 1,900 new miles at a cost of slightly under $1 billion.

  19. Climate Action Champions: Case Studies | Department of Energy

    Energy Savers [EERE]

    Case Studies Climate Action Champions: Case Studies PDF icon Boston Case Study PDF icon Dubuque Case Study PDF icon Knoxville Case Study PDF icon Metropolitan Washington Council of Governments Case Study PDF icon Oberlin Case Study PDF icon Portland Case Study PDF icon Salt Lake City Case Study PDF icon San Francisco Case Study PDF icon Seattle Case Study PDF icon Sonoma Case Study PDF icon Southeast Florida Case Study More Documents & Publications Community Organizing and Outreach Climate

  20. Method and apparatus for biological sequence comparison

    DOE Patents [OSTI]

    Marr, Thomas G. (Huntington, NY); Chang, William I-Wei (Huntington, NY)

    1997-01-01

    A method and apparatus for comparing biological sequences from a known source of sequences, with a subject (query) sequence. The apparatus takes as input a set of target similarity levels (such as evolutionary distances in units of PAM), and finds all fragments of known sequences that are similar to the subject sequence at each target similarity level, and are long enough to be statistically significant. The invention device filters out fragments from the known sequences that are too short, or have a lower average similarity to the subject sequence than is required by each target similarity level. The subject sequence is then compared only to the remaining known sequences to find the best matches. The filtering member divides the subject sequence into overlapping blocks, each block being sufficiently large to contain a minimum-length alignment from a known sequence. For each block, the filter member compares the block with every possible short fragment in the known sequences and determines a best match for each comparison. The determined set of short fragment best matches for the block provide an upper threshold on alignment values. Regions of a certain length from the known sequences that have a mean alignment value upper threshold greater than a target unit score are concatenated to form a union. The current block is compared to the union and provides an indication of best local alignment with the subject sequence.

  1. Comparison between electroglottography and electromagnetic glottography

    SciTech Connect (OSTI)

    Titze, Ingo R.; Story, Brad H.; Burnett, Gregory C.; Holzrichter, John F.; Ng, Lawrence C.; Lea, Wayne A.

    2000-01-01

    Newly developed glottographic sensors, utilizing high-frequency propagating electromagnetic waves, were compared to a well-established electroglottographic device. The comparison was made on four male subjects under different phonation conditions, including three levels of vocal fold adduction (normal, breathy, and pressed), three different registers (falsetto, chest, and fry), and two different pitches. Agreement between the sensors was always found for the glottal closure event, but for the general wave shape the agreement was better for falsetto and breathy voice than for pressed voice and vocal fry. Differences are attributed to the field patterns of the devices. Whereas the electroglottographic device can operate only in a conduction mode, the electromagnetic device can operate in either the forward scattering (diffraction) mode or in the backward scattering (reflection) mode. Results of our tests favor the diffraction mode because a more favorable angle imposed on receiving the scattered (reflected) signal did not improve the signal strength. Several observations are made on the uses of the electromagnetic sensors for operation without skin contact and possibly in an array configuration for improved spatial resolution within the glottis. (c) 2000 Acoustical Society of America.

  2. Method and apparatus for biological sequence comparison

    DOE Patents [OSTI]

    Marr, T.G.; Chang, W.I.

    1997-12-23

    A method and apparatus are disclosed for comparing biological sequences from a known source of sequences, with a subject (query) sequence. The apparatus takes as input a set of target similarity levels (such as evolutionary distances in units of PAM), and finds all fragments of known sequences that are similar to the subject sequence at each target similarity level, and are long enough to be statistically significant. The invention device filters out fragments from the known sequences that are too short, or have a lower average similarity to the subject sequence than is required by each target similarity level. The subject sequence is then compared only to the remaining known sequences to find the best matches. The filtering member divides the subject sequence into overlapping blocks, each block being sufficiently large to contain a minimum-length alignment from a known sequence. For each block, the filter member compares the block with every possible short fragment in the known sequences and determines a best match for each comparison. The determined set of short fragment best matches for the block provide an upper threshold on alignment values. Regions of a certain length from the known sequences that have a mean alignment value upper threshold greater than a target unit score are concatenated to form a union. The current block is compared to the union and provides an indication of best local alignment with the subject sequence. 5 figs.

  3. A Comparison of Simulation Capabilities for Ducts

    SciTech Connect (OSTI)

    Miller, William A.; Smith, Matt K.; Gu, Lixing; New, Joshua Ryan

    2014-11-01

    Typically, the cheapest way to install a central air conditioning system in residential buildings is to place the ductwork in the attic. Energy losses due to duct-attic interactions can be great, but current whole-house models are unable to capture the dynamic multi-mode physics of the interactions. The building industry is notoriously fragmented and unable to devote adequate research resources to solve this problem. Builders are going to continue to put ducts in the attic because floor space is too expensive to closet them within living space, and there are both construction and aesthetic issues with other approaches such as dropped ceilings. Thus, there is a substantial need to publicly document duct losses and the cost of energy used by ducts in attics so that practitioners, builders, homeowners and state and federal code officials can make informed decisions leading to changes in new construction and additional retrofit actions. Thus, the goal of this study is to conduct a comparison of AtticSim and EnergyPlus simulation algorithms to identify specific features for potential inclusion in EnergyPlus that would allow higher-fidelity modeling of HVAC operation and duct transport of conditioned air. It is anticipated that the resulting analysis from these simulation tools will inform energy decisions relating to the role of ducts in future building energy codes and standards.

  4. Comparison of EGS5 Simulations with Experiment

    SciTech Connect (OSTI)

    Nelson, W.Ralph; Field, Clive; ,

    2006-12-01

    Simulations, made using EGS5, of the longitudinal and radial distributions of energy deposition of electrons of various energies are compared with experimental results in the literature. Energies and materials are: 1 GeV in water and aluminum; 6 GeV in aluminum, copper and lead; and (longitudinal only) 28.5 GeV in alumina (Al{sub 2}O{sub 3}). There is general agreement within a few percent over most of the shower profile. Substantial discrepancies are noted at depths far beyond shower maximum, reaching {approx}30-50% in the cases of lead and copper at 6 GeV.

  5. Comparison of ring compression testing to three point bend testing...

    Office of Scientific and Technical Information (OSTI)

    growth treatment (RHGT) consisting of heating to 400C, applying initial hoop stresses ... Hydrides are generated in Zirconium based fuel cladding as a result of coolant (water) ...

  6. Decreasing Soft Costs for Solar Photovoltaics by Improving the Interconnection Process. A Case Study of Pacific Gas and Electric

    SciTech Connect (OSTI)

    Ardani, Kristen; Margolis, Robert

    2015-09-01

    In this case study, we examine how PG&E achieved a faster, more efficient interconnection approval process despite rising application volumes. Our goal is to draw insights from PG&E's experience that can help to inform decision making at other utilities across the U.S. that may face similar trajectories for DG PV market growth.

  7. Growth mechanisms, polytypism, and real structure of kaolinite microcrystals

    SciTech Connect (OSTI)

    Samotoin, N. D.

    2008-09-15

    The mechanisms of growth of kaolinite microcrystals (0.1-5.0 {mu}m in size) at deposits related to the cluvial weathering crust, as well as to the low-temperature and medium-temperature hydrothermal processes of transformations of minerals in different rocks in Russia, Kazakhstan, Ukraine, Czechia, Vietnam, India, Cuba, and Madagascar, are investigated using transmission electron microscopy and vacuum decoration with gold. It is established that kaolinite microcrystals grow according to two mechanisms: the mechanism of periodic formation of two-dimensional nuclei and the mechanism of spiral growth. The spiral growth of kaolinite microcrystals is dominant and occurs on steps of screw dislocations that differ in sign and magnitude of the Burgers vector along the c axis. The layered growth of kaolinite originates from a widespread source in the form of a step between polar (+ and -) dislocations, i.e., a growth analogue of the Frank-Read dislocation source. The density of growth screw dislocations varies over a wide range and can be as high as {approx}10{sup 9} cm{sup -2}. Layered stepped kaolinite growth pyramids for all mechanisms of growth on the (001) face of kaolinite exhibit the main features of the triclinic 1Tc and real structures of this mineral.

  8. Controlled Nucleation and Growth of Pillared Paddlewheel Framework

    Office of Scientific and Technical Information (OSTI)

    Nanostacks onto Chemically Modified Surfaces. (Journal Article) | SciTech Connect Controlled Nucleation and Growth of Pillared Paddlewheel Framework Nanostacks onto Chemically Modified Surfaces. Citation Details In-Document Search Title: Controlled Nucleation and Growth of Pillared Paddlewheel Framework Nanostacks onto Chemically Modified Surfaces. Abstract not provided. Authors: Gough, Dara ; Wheeler, David Roger ; Lambert, Timothy N. ; Rodriguez, Mark Andrew ; Spoerke, Erik David ;

  9. Structural study of growth, orientation and defects characteristics in the

    Office of Scientific and Technical Information (OSTI)

    functional microelectromechanical system material aluminium nitride (Journal Article) | SciTech Connect Structural study of growth, orientation and defects characteristics in the functional microelectromechanical system material aluminium nitride Citation Details In-Document Search Title: Structural study of growth, orientation and defects characteristics in the functional microelectromechanical system material aluminium nitride The real structure and morphology of piezoelectric aluminum

  10. Frequency sweep rates of rising tone electromagnetic ion cyclotron waves: Comparison between nonlinear theory and Cluster observation

    SciTech Connect (OSTI)

    He, Zhaoguo; Zong, Qiugang Wang, Yongfu; Liu, Siqing; Lin, Ruilin; Shi, Liqin

    2014-12-15

    Resonant pitch angle scattering by electromagnetic ion cyclotron (EMIC) waves has been suggested to account for the rapid loss of ring current ions and radiation belt electrons. For the rising tone EMIC wave (classified as triggered EMIC emission), its frequency sweep rate strongly affects the efficiency of pitch-angle scattering. Based on the Cluster observations, we analyze three typical cases of rising tone EMIC waves. Two cases locate at the nightside (22.3 and 22.6 magnetic local time (MLT)) equatorial region and one case locates at the duskside (18MLT) higher magnetic latitude (??=?9.3) region. For the three cases, the time-dependent wave amplitude, cold electron density, and cold ion density ratio are derived from satellite data; while the ambient magnetic field, thermal proton perpendicular temperature, and the wave spectral can be directly provided by observation. These parameters are input into the nonlinear wave growth model to simulate the time-frequency evolutions of the rising tones. The simulated results show good agreements with the observations of the rising tones, providing further support for the previous finding that the rising tone EMIC wave is excited through the nonlinear wave growth process.

  11. Workshop on nuclear power growth and nonproliferation

    SciTech Connect (OSTI)

    Pilat, Joseph F

    2010-01-01

    It is widely viewed that an expansion of nuclear power would have positive energy, economic and environmental benefits for the world. However, there are concerns about the economic competitiveness, safety and proliferation and terrorism risks of nuclear power. The prospects for a dramatic growth in nuclear power will depend on the ability of governments and industry to address these concerns, including the effectiveness of, and the resources devoted to, plans to develop and implement technologies and approaches that strengthen nonproliferation, nuclear materials accountability and nuclear security. In his Prague speech, President Obama stated: 'we should build a new framework for civil nuclear cooperation, including an international fuel bank, so that countries can access peaceful power without increasing the risks of proliferation. That must be the right of every nation that renounces nuclear weapons, especially developing countries embarking on peaceful programs. And no approach will succeed if it's based on the denial of rights to nations that play by the rules. We must harness the power of nuclear energy on behalf of our efforts to combat climate change, and to advance peace opportunity for all people.' How can the President's vision, which will rekindle a vigorous public debate over the future of nuclear power and its relation to proliferation, be realized? What critical issues will frame the reemerging debate? What policies must be put into place to address these issues? Will US policy be marked more by continuity or change? To address these and other questions, the Los Alamos National Laboratory in cooperation with the Woodrow Wilson International Center for Scholars will host a workshop on the future of nuclear power and nonproliferation.

  12. Growth Rates of Global Energy Systems and Future Outlooks

    SciTech Connect (OSTI)

    Hoeoek, Mikael; Li, Junchen; Johansson, Kersti; Snowden, Simon

    2012-03-15

    The world is interconnected and powered by a number of global energy systems using fossil, nuclear, or renewable energy. This study reviews historical time series of energy production and growth for various energy sources. It compiles a theoretical and empirical foundation for understanding the behaviour underlying global energy systems' growth. The most extreme growth rates are found in fossil fuels. The presence of scaling behaviour, i.e. proportionality between growth rate and size, is established. The findings are used to investigate the consistency of several long-range scenarios expecting rapid growth for future energy systems. The validity of such projections is questioned, based on past experience. Finally, it is found that even if new energy systems undergo a rapid 'oil boom'-development-i.e. they mimic the most extreme historical events-their contribution to global energy supply by 2050 will be marginal.

  13. String stabilized ribbon growth a method for seeding same

    DOE Patents [OSTI]

    Sachs, Emanuel M. (39 Harding Ave., Belmont, MA 02178)

    1987-08-25

    This invention is a method of initiating or seeding the growth of a crystalline or polycrystalline ribbon by the String Stabilized Ribbon Growth Method. The method for seeding the crystal growth comprises contacting a melt surface with a seed and two strings used in edge stabilization. The wetted strings attach to the wetted seed as a result of the freezing of the liquid melt. Upon drawing the seed, which is attached to the strings, away from the melt surface a melt liquid meniscus, a seed junction, and a growth interface forms. Further pulling of the attached seed causes a crystal ribbon to grow at the growth interface. The boundaries of the growing ribbon are: at the top the seed junction, at the bottom the freezing boundary of the melt liquid meniscus, and at the edges frozen-in strings.

  14. Guidance system for low angle silicon ribbon growth

    DOE Patents [OSTI]

    Jewett, David N.; Bates, Herbert E.; Milstein, Joseph B.

    1986-07-08

    In a low angle silicon sheet growth process, a puller mechanism advances a seed crystal and solidified ribbon from a cooled growth zone in a melt at a low angle with respect to the horizontal. The ribbon is supported on a ramp adjacent the puller mechanism. Variations in the vertical position of the ribbon with respect to the ramp are isolated from the growth end of the ribbon by (1) growing the ribbon so that it is extremely thin, preferably less than 0.7 mm, (2) maintaining a large growth zone, preferably one whose length is at least 5.0 cm, and (3) spacing the ramp from the growth zone by at least 15 cm.

  15. Shallow melt apparatus for semicontinuous czochralski crystal growth

    DOE Patents [OSTI]

    Wang, Tihu; Ciszek, Theodore F.

    2006-01-10

    In a single crystal pulling apparatus for providing a Czochralski crystal growth process, the improvement of a shallow melt In a single crystal pulling apparatus for providing a Czochralski crystal growth process, the improvement of a shallow melt crucible (20) to eliminate the necessity supplying a large quantity of feed stock materials that had to be preloaded in a deep crucible to grow a large ingot, comprising a gas tight container a crucible with a deepened periphery (25) to prevent snapping of a shallow melt and reduce turbulent melt convection; source supply means for adding source material to the semiconductor melt; a double barrier (23) to minimize heat transfer between the deepened periphery (25) and the shallow melt in the growth compartment; offset holes (24) in the double barrier (23) to increase melt travel length between the deepened periphery (25) and the shallow growth compartment; and the interface heater/heat sink (22) to control the interface shape and crystal growth rate.

  16. Controlling Condensation and Frost Growth with Chemical Micropatterns

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Boreyko, Jonathan; Hansen, Ryan; Murphy, Kevin R; Nath, Saurabh; Retterer, Scott T; Collier, Pat

    2016-01-01

    Frost growth on chilled hydrophobic surfaces is an inter-droplet phenomenon, where frozen droplets harvest water from supercooled liquid droplets to grow ice bridges that propagate across the surface in a chain reaction. To date, no surface has been able to passively prevent the in-plane growth of frost across the population of supercooled condensate. Here, we demonstrate that when the nucleation sites for supercooled condensate are properly controlled with chemical micropatterns, the speed of frost growth can be slowed and even halted entirely. This stoppage of frost growth is attributed to the large interdroplet separation between condensate upon the onset ofmore »freezing, which was controlled by the pitch of the chemical patterns and by deliberately triggering an early freezing event. These findings reveal that frost growth can be passively suppressed by designing surfaces to spatially control nucleation sites and/or temporally control the onset of freezing events.« less

  17. Climate Impact of Transportation A Model Comparison

    SciTech Connect (OSTI)

    Girod, Bastien; Van Vuuren, Detlef; Grahn, Maria; Kitous, Alban; Kim, Son H.; Kyle, G. Page

    2013-06-01

    Transportation contributes to a significant and rising share of global energy use and GHG emissions. Therefore modeling future travel demand, its fuel use, and resulting CO2 emission is highly relevant for climate change mitigation. In this study we compare the baseline projections for global service demand (passenger-kilometers, ton-kilometers), fuel use, and CO2 emissions of five different global transport models using harmonized input assumptions on income and population. For four models we also evaluate the impact of a carbon tax. All models project a steep increase in service demand over the century. Technology is important for limiting energy consumption and CO2 emissions, but quite radical changes in the technology mix are required to stabilize or reverse the trend. While all models project liquid fossil fuels dominating up to 2050, they differ regarding the use of alternative fuels (natural gas, hydrogen, biofuels, and electricity), because of different fuel price projections. The carbon tax of US$200/tCO2 in 2050 stabilizes or reverses global emission growth in all models. Besides common findings many differences in the model assumptions and projections indicate room for improvement in modeling and empirical description of the transport system.

  18. Zero Net Energy Homes Production Builder Business Case: California/Florida

    Broader source: Energy.gov (indexed) [DOE]

    Production Builders - Building America Top Innovation | Department of Energy solar home. Building America's production builder partners have found that energy efficiency helps them sell more homes and sell them faster than their competitors even at a higher price point. These impressive business case results have helped influence substantial growth in zero net-energy homes. This Top Innovation profile describes four California home builders who worked with Building America teams to

  19. Methods of preparing flexible photovoltaic devices using epitaxial liftoff, and preserving the integrity of growth substrates used in epitaxial growth

    DOE Patents [OSTI]

    Forrest, Stephen R; Zimmerman, Jeramy; Lee, Kyusang; Shiu, Kuen-Ting

    2015-01-06

    There is disclosed methods of making photosensitive devices, such as flexible photovoltaic (PV) devices, through the use of epitaxial liftoff. Also described herein are methods of preparing flexible PV devices comprising a structure having a growth substrate, wherein the selective etching of protective layers yields a smooth growth substrate that us suitable for reuse.

  20. Methods of preparing flexible photovoltaic devices using epitaxial liftoff, and preserving the integrity of growth substrates used in epitaxial growth

    DOE Patents [OSTI]

    Forrest, Stephen R; Zimmerman, Jeramy; Lee, Kyusang; Shiu, Kuen-Ting

    2013-02-19

    There is disclosed methods of making photosensitive devices, such as flexible photovoltaic (PV) devices, through the use of epitaxial liftoff. Also described herein are methods of preparing flexible PV devices comprising a structure having a growth substrate, wherein the selective etching of protective layers yields a smooth growth substrate that us suitable for reuse.

  1. Fuel Cell Case Study | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Case Study Fuel Cell Case Study Presented at the Clean Energy States Alliance and U.S. Department of Energy Webinar: Fuel Cells for Supermarkets, April 4, 2011. PDF icon infocallapr11_loftus.pdf More Documents & Publications The Business Case for Fuel Cells 2011: Energizing America's Top Companies The Business Case for Fuel Cells 2010: Why Top Companies are Purchasing Fuel Cells Today DOE Zero Energy Ready Home Case Study: Glastonbury Housesmith, Hickory Drive, South Glastonbury, CT

  2. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    U.S. Energy Information Administration | International Energy Outlook 2014 High Oil Price case projections Table B3. World petroleum and other liquids consumption by region and end-use sector, High Oil Price case, 2010-40 (quadrillion Btu) Region History Projections Average annual percent change, 2010-40 2010 2020 2025 2030 2035 2040 OECD United States Residential 1.1 0.9 0.8 0.7 0.7 0.6 -1.9 Commercial 0.7 0.6 0.6 0.6 0.6 0.6 -0.3 Industrial 8.1 9.4 9.9 9.9 10.0 10.0 0.7 Transportation 26.9

  3. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    3 U.S. Energy Information Administration | International Energy Outlook 2014 High Oil Price case projections Table B4. World petroleum and other liquids production by region and country, High Oil Price case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030 2035 2040 OPEC a 34.1 35.4 35.7 33.1 34.5 37.8 41.0 43.7 0.7 Middle East 23.2 24.3 25.9 22.6 23.6 26.6 29.4 31.8 0.9 North Africa 3.8 3.7 2.4 3.2 3.3 3.4 3.6 3.7

  4. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    5 U.S. Energy Information Administration | International Energy Outlook 2014 High Oil Price case projections Table B6. World other liquid fuels a production by region and country, High Oil Price case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030 2035 2040 OPEC b 3.1 3.3 3.5 4.6 4.9 5.3 5.8 5.9 1.9 Natural gas plant liquids 3.1 3.3 3.4 4.3 4.6 4.9 5.3 5.3 1.6 Biofuels c 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 -

  5. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    5 U.S. Energy Information Administration | International Energy Outlook 2014 Low Oil Price case projections Table C4. World petroleum and other liquids production by region and country, Low Oil Price case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030 2035 2040 OPEC a 34.1 35.4 35.7 43.3 48.7 54.6 59.9 65.3 2.1 Middle East 23.2 24.3 25.9 30.4 34.5 38.9 43.0 47.3 2.2 North Africa 3.8 3.7 2.4 3.7 4.0 4.3 4.7 4.9

  6. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    7 U.S. Energy Information Administration | International Energy Outlook 2014 Low Oil Price case projections Table C6. World other liquid fuels a production by region and country, Low Oil Price case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030 2035 2040 OPEC b 3.1 3.3 3.5 4.3 4.5 4.8 5.1 5.0 1.4 Natural gas plant liquids 3.1 3.3 3.4 4.0 4.2 4.4 4.8 4.7 1.2 Biofuels c 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 -

  7. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    U.S. Energy Information Administration | International Energy Outlook 2014 Reference case projections Table A3. World petroleum and other liquids consumption by region and end-use sector, Reference case, 2010-40 (quadrillion Btu) Region History Projections Average annual percent change, 2010-40 2010 2020 2025 2030 2035 2040 OECD United States Residential 1.1 0.9 0.8 0.8 0.7 0.7 -1.8 Commercial 0.7 0.7 0.7 0.7 0.7 0.7 0.1 Industrial 8.1 9.6 9.9 10.1 10.1 10.1 0.7 Transportation 26.9 25.6 24.7

  8. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    U.S. Energy Information Administration | International Energy Outlook 2014 Reference case projections Table A4. World petroleum and other liquids production by region and country, Reference case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030 2035 2040 OPEC a 34.1 35.4 35.7 38.7 40.7 44.4 48.2 52.1 1.3 Middle East 23.2 24.3 25.9 27.1 28.8 32.2 35.5 38.8 1.6 North Africa 3.8 3.7 2.4 3.5 3.6 3.7 3.8 4.1 0.3 West

  9. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    3 U.S. Energy Information Administration | International Energy Outlook 2014 Reference case projections Table A6. World other liquid fuels a production by region and country, Reference case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030 2035 2040 OPEC b 3.1 3.3 3.5 4.3 4.6 4.9 5.3 5.9 1.9 Natural gas plant liquids 3.1 3.3 3.4 4.0 4.2 4.5 4.9 5.4 1.7 Biofuels c 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 - Coal-to-liquids 0.0

  10. Orange and Rockland Case Study

    Energy Savers [EERE]

    10 2012 Orange and Rockland Case Study 1 Voltage Control Device A "Model-Centric" Approach to Smarter Electric Distribution Systems Orange and Rockland Utilities (ORU), is an investor-owned utility and a subsidiary of Consolidated Edison Incorporated (Con Edison), and is located in suburban New York, New Jersey, and Pennsylvania, west of New York City. ORU is a key participant in Con Edison's $272 million Smart Grid Investment Grant (SGIG) project to modernize electric distribution

  11. West Virginia: A Compelling Case

    Broader source: Energy.gov (indexed) [DOE]

    West Virginia: A Compelling Case Rich energy history; solid energy expertise West Virginia is an energy state. With a population of just 1.8 million, the state contributes significantly to the energy needs of the eastern United States.  West Virginia is No. 2 in coal production behind Wyoming  West Virginia is No. 4 behind Pennsylvania, Alabama and Illinois in net electricity exports, exporting 60 percent of the electricity it generates  West Virginia is No. 10 in natural gas production

  12. Case Study - Liquefied Natural Gas

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Environmental Science Enviro Express Kenworth LNG tractor. Connecticut Clean Cities Future Fuels Project Case Study - Liquefied Natural Gas As a part of the U.S. Department of Energy's broad effort to develop cleaner transportation technologies that reduce U.S. dependence on imported oil, this study examines advanced 2011 natural gas fueled trucks using liquefied natural gas (LNG) replacing older diesel fueled trucks. The trucks are used 6 days per week in regional city-to-landfill long hauls of

  13. Operating Reserves and Wind Power Integration: An International Comparison; Preprint

    SciTech Connect (OSTI)

    Milligan, M.; Donohoo, P.; Lew, D.; Ela, E.; Kirby, B.; Holttinen, H.; Lannoye, E.; Flynn, D.; O'Malley, M.; Miller, N.; Eriksen, P. B.; Gottig, A.; Rawn, B.; Gibescu, M.; Lazaro, E. G.; Robitaille, A.; Kamwa, I.

    2010-10-01

    This paper provides a high-level international comparison of methods and key results from both operating practice and integration analysis, based on an informal International Energy Agency Task 25: Large-scale Wind Integration.

  14. ARM - Field Campaign - IRSI Inter-Comparison Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    would love to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : IRSI Inter-Comparison Study 2007.08.27 - 2007.09.23 Lead Scientist : Victor Morris...

  15. ARM - Field Campaign - MWR Inter-Comparison Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    would love to hear from you Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : MWR Inter-Comparison Study 2006.10.09 - 2006.11.30 Lead Scientist : Maria Cadeddu...

  16. ARM - Field Campaign - Cloudiness Inter-Comparison IOP

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    govCampaignsCloudiness Inter-Comparison IOP Campaign Links Science Plan General Information ARM Data Discovery Browse Data Comments? We would love to hear from you Send us a note...

  17. 2007 CBECS Large Hospital Building FAQs: 2003-2007 Comparison...

    Gasoline and Diesel Fuel Update (EIA)

    FAQs: 2003-2007 Comparison Graphs Main Report | Methodology | FAQ | List of Tables CBECS 2007 - Release date: August 17, 2012 Jump to: Figure 1 | Figure 2 | Figure 3 | Figure 4 |...

  18. Offshore Code Comparison Collaboration, Continuation: Phase II Results of a Floating Semisubmersible Wind System: Preprint

    SciTech Connect (OSTI)

    Robertson, A.; Jonkman, J.; Musial, W.; Vorpahl, F.; Popko, W.

    2013-11-01

    Offshore wind turbines are designed and analyzed using comprehensive simulation tools that account for the coupled dynamics of the wind inflow, aerodynamics, elasticity, and controls of the turbine, along with the incident waves, sea current, hydrodynamics, and foundation dynamics of the support structure. The Offshore Code Comparison Collaboration (OC3), which operated under the International Energy Agency (IEA) Wind Task 23, was established to verify the accuracy of these simulation tools [1]. This work was then extended under the Offshore Code Comparison Collaboration, Continuation (OC4) project under IEA Wind Task 30 [2]. Both of these projects sought to verify the accuracy of offshore wind turbine dynamics simulation tools (or codes) through code-to-code comparison of simulated responses of various offshore structures. This paper describes the latest findings from Phase II of the OC4 project, which involved the analysis of a 5-MW turbine supported by a floating semisubmersible. Twenty-two different organizations from 11 different countries submitted results using 24 different simulation tools. The variety of organizations contributing to the project brought together expertise from both the offshore structure and wind energy communities. Twenty-one different load cases were examined, encompassing varying levels of model complexity and a variety of metocean conditions. Differences in the results demonstrate the importance and accuracy of the various modeling approaches used. Significant findings include the importance of mooring dynamics to the mooring loads, the role nonlinear hydrodynamic terms play in calculating drift forces for the platform motions, and the difference between global (at the platform level) and local (at the member level) modeling of viscous drag. The results from this project will help guide development and improvement efforts for these tools to ensure that they are providing the accurate information needed to support the design and analysis needs of the offshore wind community.

  19. A Comparison of Cross-Sector Cyber Security Standards

    SciTech Connect (OSTI)

    Robert P. Evans

    2005-09-01

    This report presents a review and comparison (commonality and differences) of three cross-sector cyber security standards and an internationally recognized information technology standard. The comparison identifies the security areas covered by each standard and reveals where the standards differ in emphasis. By identifying differences in the standards, the user can evaluate which standard best meets their needs. For this report, only cross-sector standards were reviewed.

  20. Comparison of Joint Modeling Approaches Including Eulerian Sliding

    Office of Scientific and Technical Information (OSTI)

    Interfaces (Technical Report) | SciTech Connect Comparison of Joint Modeling Approaches Including Eulerian Sliding Interfaces Citation Details In-Document Search Title: Comparison of Joint Modeling Approaches Including Eulerian Sliding Interfaces Accurate representation of discontinuities such as joints and faults is a key ingredient for high fidelity modeling of shock propagation in geologic media. The following study was done to improve treatment of discontinuities (joints) in the Eulerian

  1. Comparison of Uncertainty of Two Precipitation Prediction Models at Los

    Office of Scientific and Technical Information (OSTI)

    Alamos National Lab Technical Area 54 (Technical Report) | SciTech Connect Comparison of Uncertainty of Two Precipitation Prediction Models at Los Alamos National Lab Technical Area 54 Citation Details In-Document Search Title: Comparison of Uncertainty of Two Precipitation Prediction Models at Los Alamos National Lab Technical Area 54 Meteorological inputs are an important part of subsurface flow and transport modeling. The choice of source for meteorological data used as inputs has

  2. Crystalline Ceramic Waste Forms: Comparison Of Reference Process For

    Office of Scientific and Technical Information (OSTI)

    Ceramic Waste Form Fabrication (Technical Report) | SciTech Connect Crystalline Ceramic Waste Forms: Comparison Of Reference Process For Ceramic Waste Form Fabrication Citation Details In-Document Search Title: Crystalline Ceramic Waste Forms: Comparison Of Reference Process For Ceramic Waste Form Fabrication The research conducted in this work package is aimed at taking advantage of the long term thermodynamic stability of crystalline ceramics to create more durable waste forms (as compared

  3. Comparison between MSW ash and RDF ash from incineration process

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect Comparison between MSW ash and RDF ash from incineration process Citation Details In-Document Search Title: Comparison between MSW ash and RDF ash from incineration process Resource recovery plants with waste sorting process prior to incineration have not been successfully developed in many developing countries. The reuse potential of incineration ash in light of toxicity and compressive strength remains unclear due to the inhomogeneous composition and higher

  4. Comparison between MSW ash and RDF ash from incineration process

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect Comparison between MSW ash and RDF ash from incineration process Citation Details In-Document Search Title: Comparison between MSW ash and RDF ash from incineration process × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit OSTI to utilize additional information resources in energy science and

  5. A comparison between characteristics of atmospheric-pressure plasma jets

    Office of Scientific and Technical Information (OSTI)

    sustained by nanosecond- and microsecond-pulse generators in helium (Journal Article) | SciTech Connect A comparison between characteristics of atmospheric-pressure plasma jets sustained by nanosecond- and microsecond-pulse generators in helium Citation Details In-Document Search Title: A comparison between characteristics of atmospheric-pressure plasma jets sustained by nanosecond- and microsecond-pulse generators in helium Power source is an important parameter that can affect the

  6. Characterization and comparison of devices fabricated from epitaxial

    Office of Scientific and Technical Information (OSTI)

    graphene on SiC and electrostatically transferred graphene. (Conference) | SciTech Connect Characterization and comparison of devices fabricated from epitaxial graphene on SiC and electrostatically transferred graphene. Citation Details In-Document Search Title: Characterization and comparison of devices fabricated from epitaxial graphene on SiC and electrostatically transferred graphene. Abstract not provided. Authors: Howell, Stephen W. ; Biedermann, Laura Butler ; Beechem III, Thomas

  7. Checkpoint Compression: Its Limitations and Comparisons with other

    Office of Scientific and Technical Information (OSTI)

    Optimizations. (Conference) | SciTech Connect Limitations and Comparisons with other Optimizations. Citation Details In-Document Search Title: Checkpoint Compression: Its Limitations and Comparisons with other Optimizations. Abstract not provided. Authors: Ferreira, Kurt Brian ; Ibtesham, Dewan ; Arnold, Dorian Publication Date: 2013-11-01 OSTI Identifier: 1120837 Report Number(s): SAND2013-9997C 482778 DOE Contract Number: DE-AC04-94AL85000 Resource Type: Conference Resource Relation:

  8. Checkpoint Compression: Its Limits and a Comparison with other

    Office of Scientific and Technical Information (OSTI)

    Optimizations. (Conference) | SciTech Connect Limits and a Comparison with other Optimizations. Citation Details In-Document Search Title: Checkpoint Compression: Its Limits and a Comparison with other Optimizations. Abstract not provided. Authors: Ferreira, Kurt Brian ; Ibtesham, Dewan ; Arnold, Dorian Publication Date: 2013-05-01 OSTI Identifier: 1080332 Report Number(s): SAND2013-4325C 455901 DOE Contract Number: AC04-94AL85000 Resource Type: Conference Resource Relation: Conference: IEEE

  9. Comparison of Clean Diesel Buses to CNG Buses

    Office of Scientific and Technical Information (OSTI)

    COMPARISON OF CLEAN DIESEL BUSES TO CNG BUSES Dana M. Lowell MTA New York City Transit, Department of Buses, Research & Development William Parsley MTA New York City Transit, Department of Buses, Research & Development Christopher Bush MTA New York City Transit, Department of Buses, Research & Development Douglas Zupo MTA New York City Transit, Department of Buses, Research & Development Comparison of Clean Diesel Buses to CNG Buses ABSTRACT Using previously published data on

  10. Estimating the Wind Resource in Uttarakhand: Comparison of Dynamic

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Downscaling with Doppler Lidar Wind Measurements | Department of Energy Estimating the Wind Resource in Uttarakhand: Comparison of Dynamic Downscaling with Doppler Lidar Wind Measurements Estimating the Wind Resource in Uttarakhand: Comparison of Dynamic Downscaling with Doppler Lidar Wind Measurements Previous estimates of the wind resources in Uttarakhand, India, suggest minimal wind resources in this region. To explore whether or not the complex terrain in fact provides localized regions

  11. Distributed Wind Policy Comparison Tool | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Distributed Wind Policy Comparison Tool Distributed Wind Policy Comparison Tool Power through Policy: 'Best Practices' for Cost-Effective Distributed Wind is a U.S. Department of Energy (DOE)-funded project to identify distributed wind technology policy best practices and to help policymakers, utilities, advocates, and consumers examine their effectiveness using a pro forma model. Incorporating a customized feed from the Database of State Incentives for Renewables and Efficiency (DSIRE), the

  12. Backup Power Cost of Ownership Analysis and Incumbent Technology Comparison

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy Backup Power Cost of Ownership Analysis and Incumbent Technology Comparison Backup Power Cost of Ownership Analysis and Incumbent Technology Comparison This cost of ownership analysis identifies the factors impacting the value proposition for fuel cell backup power and presents the estimated annualized cost of ownership for fuel cell backup power systems compared with the incumbent technologies of battery and diesel generator systems. The analysis compares three

  13. EAC Presentation: Comparison Among Three Studies (July 12, 2011) |

    Office of Environmental Management (EM)

    Department of Energy Comparison Among Three Studies (July 12, 2011) EAC Presentation: Comparison Among Three Studies (July 12, 2011) Presentation by L. T. Papay before the Electricity Advisorty Committee on July 12, 2011, analyzing three studies: Roadmap 2050: a practical guide to a prosperous, low carbon Europe(ECF) 2010 America's Energy Future(National Academies) 2009 California's Energy Future: Reducing GHG emissions 80% below 1990(CCST) 2011 PDF icon Charge 7: 2020 Vision, Early Start-up

  14. Effects of numerical methods on comparisons between experiments and simulations of shock-accelerated mixing.

    SciTech Connect (OSTI)

    Rider, William; Kamm, J. R.; Tomkins, C. D.; Zoldi, C. A.; Prestridge, K. P.; Marr-Lyon, M.; Rightley, P. M.; Benjamin, R. F.

    2002-01-01

    We consider the detailed structures of mixing flows for Richtmyer-Meshkov experiments of Prestridge et al. [PRE 00] and Tomkins et al. [TOM 01] and examine the most recent measurements from the experimental apparatus. Numerical simulations of these experiments are performed with three different versions of high resolution finite volume Godunov methods. We compare experimental data with simulations for configurations of one and two diffuse cylinders of SF{sub 6} in air using integral measures as well as fractal analysis and continuous wavelet transforms. The details of the initial conditions have a significant effect on the computed results, especially in the case of the double cylinder. Additionally, these comparisons reveal sensitive dependence of the computed solution on the numerical method.

  15. Dual chain synthetic heparin-binding growth factor analogs

    DOE Patents [OSTI]

    Zamora, Paul O.; Pena, Louis A.; Lin, Xinhua

    2009-10-06

    The invention provides synthetic heparin-binding growth factor analogs having two peptide chains each branched from a branch moiety, such as trifunctional amino acid residues, the branch moieties separated by a first linker of from 3 to about 20 backbone atoms, which peptide chains bind a heparin-binding growth factor receptor and are covalently bound to a non-signaling peptide that includes a heparin-binding domain, preferably by a second linker, which may be a hydrophobic second linker. The synthetic heparin-binding growth factor analogs are useful as pharmaceutical agents, soluble biologics or as surface coatings for medical devices.

  16. Dual chain synthetic heparin-binding growth factor analogs

    DOE Patents [OSTI]

    Zamora, Paul O.; Pena, Louis A.; Lin, Xinhua

    2012-04-24

    The invention provides synthetic heparin-binding growth factor analogs having two peptide chains each branched from a branch moiety, such as trifunctional amino acid residues, the branch moieties separated by a first linker of from 3 to about 20 backbone atoms, which peptide chains bind a heparin-binding growth factor receptor and are covalently bound to a non-signaling peptide that includes a heparin-binding domain, preferably by a second linker, which may be a hydrophobic second linker. The synthetic heparin-binding growth factor analogs are useful as pharmaceutical agents, soluble biologics or as surface coatings for medical devices.

  17. Manufacturing process to reduce large grain growth in zirconium alloys

    DOE Patents [OSTI]

    Rosecrans, P.M.

    1984-08-01

    It is an object of the present invention to provide a procedure for desensitizing zirconium-based alloys to large grain growth (LGG) during thermal treatment above the recrystallization temperature of the alloy. It is a further object of the present invention to provide a method for treating zirconium-based alloys which have been cold-worked in the range of 2 to 8% strain to reduce large grain growth. It is another object of the present invention to provide a method for fabricating a zirconium alloy clad nuclear fuel element wherein the zirconium clad is resistant to large grain growth.

  18. Kinetics of monolayer graphene growth by segregation on Pd(111)

    SciTech Connect (OSTI)

    Mok, H. S.; Murata, Y.; Kodambaka, S., E-mail: kodambaka@ucla.edu [Department of Materials Science and Engineering, University of California Los Angeles, Los Angeles, California 90095 (United States); Ebnonnasir, A.; Ciobanu, C. V. [Department of Mechanical Engineering and Materials Science Program, Colorado School of Mines, Golden, Colorado 80401 (United States); Nie, S.; McCarty, K. F. [Sandia National Laboratories, Livermore, California 94550 (United States)

    2014-03-10

    Using in situ low-energy electron microscopy and density functional theory calculations, we follow the growth of monolayer graphene on Pd(111) via surface segregation of bulk-dissolved carbon. Upon lowering the substrate temperature, nucleation of graphene begins on graphene-free Pd surface and continues to occur during graphene growth. Measurements of graphene growth rates and Pd surface work functions establish that this continued nucleation is due to increasing C adatom concentration on the Pd surface with time. We attribute this anomalous phenomenon to a large barrier for attachment of C adatoms to graphene coupled with a strong binding of the non-graphitic C to the Pd surface.

  19. Electricity generation and environmental externalities: Case studies, September 1995

    SciTech Connect (OSTI)

    1995-09-28

    Electricity constitutes a critical input in sustaining the Nation`s economic growth and development and the well-being of its inhabitants. However, there are byproducts of electricity production that have an undesirable effect on the environment. Most of these are emissions introduced by the combustion of fossil fuels, which accounts for nearly 70 percent of the total electricity generated in the United States. The environmental impacts (or damages) caused by these emissions are labeled environmental ``externalities.`` Included in the generic term ``externality`` are benefits or costs resulting as an unintended byproduct of an economic activity that accrue to someone other than the parties involved in the activity. This report provides an overview of the economic foundation of externalities, the Federal and State regulatory approaches, and case studies of the impacts of the externality policies adopted by three States.

  20. A Case Study in Proton Pencil-Beam Scanning Delivery

    SciTech Connect (OSTI)

    Kooy, Hanne M.; Clasie, Benjamin M.; Lu, H.-M.; Madden, Thomas M.; Bentefour, Hassan; Depauw, Nicolas M.S.; Adams, Judy A.; Trofimov, Alexei V.; Demaret, Denis; Delaney, Thomas F.; Flanz, Jacob B.

    2010-02-01

    Purpose: We completed an implementation of pencil-beam scanning (PBS), a technology whereby a focused beam of protons, of variable intensity and energy, is scanned over a plane perpendicular to the beam axis and in depth. The aim of radiotherapy is to improve the target to healthy tissue dose differential. We illustrate how PBS achieves this aim in a patient with a bulky tumor. Methods and Materials: Our first deployment of PBS uses 'broad' pencil-beams ranging from 20 to 35 mm (full-width-half-maximum) over the range interval from 32 to 7 g/cm{sup 2}. Such beam-brushes offer a unique opportunity for treating bulky tumors. We present a case study of a large (4,295 cc clinical target volume) retroperitoneal sarcoma treated to 50.4 Gy relative biological effectiveness (RBE) (presurgery) using a course of photons and protons to the clinical target volume and a course of protons to the gross target volume. Results: We describe our system and present the dosimetry for all courses and provide an interdosimetric comparison. Discussion: The use of PBS for bulky targets reduces the complexity of treatment planning and delivery compared with collimated proton fields. In addition, PBS obviates, especially for cases as presented here, the significant cost incurred in the construction of field-specific hardware. PBS offers improved dose distributions, reduced treatment time, and reduced cost of treatment.

  1. Visualization of Growth Curve Data from Phenotype MicroarrayExperiments

    SciTech Connect (OSTI)

    Jacobsen, Janet S.; Joyner, Dominique C.; Borglin, Sharon E.; Hazen, Terry C.; Arkin, Adam P.; Bethel, E. Wes

    2007-04-19

    Phenotype microarrays provide a technology to simultaneouslysurvey the response of an organism to nearly 2,000 substrates, includingcarbon, nitrogen and potassium sources; varying pH; varying saltconcentrations; and antibiotics. In order to more quickly and easily viewand compare the large number of growth curves produced by phenotypemicroarray experiments, we have developed software to produce and displaycolor images, each of which corresponds to a set of 96 growth curves.Using color images to represent growth curves data has proven to be avaluable way to assess experiment quality, compare replicates, facilitatecomparison of the responses of different organisms, and identifysignificant phenotypes. The color images are linked to traditional plotsof growth versus time, as well as to information about the experiment,organism, and substrate. In order to share and view information and dataproject-wide, all information, plots, and data are accessible using onlya Web browser.

  2. Growth and Discovery of Novel Materials | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Growth and Discovery of Novel Materials During this SULI program the student will learn how to grow single crystals of novel intermetallic compounds as part of the on-going Ames...

  3. Methods for improved growth of group III nitride semiconductor compounds

    DOE Patents [OSTI]

    Melnik, Yuriy; Chen, Lu; Kojiri, Hidehiro

    2015-03-17

    Methods are disclosed for growing group III-nitride semiconductor compounds with advanced buffer layer technique. In an embodiment, a method includes providing a suitable substrate in a processing chamber of a hydride vapor phase epitaxy processing system. The method includes forming an AlN buffer layer by flowing an ammonia gas into a growth zone of the processing chamber, flowing an aluminum halide containing precursor to the growth zone and at the same time flowing additional hydrogen halide or halogen gas into the growth zone of the processing chamber. The additional hydrogen halide or halogen gas that is flowed into the growth zone during buffer layer deposition suppresses homogeneous AlN particle formation. The hydrogen halide or halogen gas may continue flowing for a time period while the flow of the aluminum halide containing precursor is turned off.

  4. Shallow Melt Apparatus for Semicontinuous Czochralski Crystal Growth

    DOE Patents [OSTI]

    Wang, T.; Ciszek, T. F.

    2006-01-10

    In a single crystal pulling apparatus for providing a Czochralski crystal growth process, the improvement of a shallow melt crucible (20) to eliminate the necessity supplying a large quantity of feed stock materials that had to be preloaded in a deep crucible to grow a large ingot, comprising a gas tight container a crucible with a deepened periphery (25) to prevent snapping of a shallow melt and reduce turbulent melt convection; source supply means for adding source material to the semiconductor melt; a double barrier (23) to minimize heat transfer between the deepened periphery (25) and the shallow melt in the growth compartment; offset holes (24) in the double barrier (23) to increase melt travel length between the deepened periphery (25) and the shallow growth compartment; and the interface heater/heat sink (22) to control the interface shape and crystal growth rate.

  5. Cart or Horse: Transport and Economic Growth | Open Energy Information

    Open Energy Info (EERE)

    it can constrain growth, as congestion and unreliable transport systems can exact a heavy price. But as long as the transport system is "good enough", the returns to greater...

  6. CASL - Effect of Grain Boundaries on Irradiation Growth of Zirconium...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    vacancy loops on the basal planes. In 2011, the ORNL-based team established a reaction-diffusion model for prediction of irradiation growth at an atomistic level, accounting for...

  7. The US Geothermal Industry: Three Decades of Growth | Open Energy...

    Open Energy Info (EERE)

    Three Decades of Growth Abstract Over the last three decades the U.S. geothermal power-generation industry has grown to be the largest in the world,with over 2700 MW of...

  8. Understanding Cost Growth and Performance Shortfalls in Pioneer Process

    Office of Environmental Management (EM)

    Plants | Department of Energy Cost Growth and Performance Shortfalls in Pioneer Process Plants Understanding Cost Growth and Performance Shortfalls in Pioneer Process Plants This report presents an empirical and quantitative analysis of the misestimation of the capital costs and performance of innovative energy process plants and other chemical process facilities that create fundamental problems for government and industry in planning the development and commercialization of such plants. PDF

  9. Multibump solutions for quasilinear elliptic equations with critical growth

    SciTech Connect (OSTI)

    Liu, Jiaquan; Wang, Zhi-Qiang; Wu, Xian

    2013-12-15

    The current paper is concerned with constructing multibump solutions for a class of quasilinear Schrdinger equations with critical growth. This extends the classical results of Coti Zelati and Rabinowitz [Commun. Pure Appl. Math. 45, 12171269 (1992)] for semilinear equations as well as recent work of Liu, Wang, and Guo [J. Funct. Anal. 262, 40404102 (2012)] for quasilinear problems with subcritical growth. The periodicity of the potentials is used to glue ground state solutions to construct multibump bound state solutions.

  10. Molecular design for growth of supramolecular membranes with hierarchical

    Office of Scientific and Technical Information (OSTI)

    structure (Journal Article) | SciTech Connect Molecular design for growth of supramolecular membranes with hierarchical structure Citation Details In-Document Search Title: Molecular design for growth of supramolecular membranes with hierarchical structure Authors: Zha, R. Helen ; Velichko, Yuri S. ; Bitton, Ronit ; Stupp, Samuel I. [1] + Show Author Affiliations (NWU) Publication Date: 2016-02-10 OSTI Identifier: 1237763 Resource Type: Journal Article Resource Relation: Journal Name: Soft

  11. GROWTH AND ELECTROCHEMICAL CHARACTERIZATION OF CARBON NANOSPIKE THIN FILM

    Office of Scientific and Technical Information (OSTI)

    ELECTRODES (Journal Article) | SciTech Connect GROWTH AND ELECTROCHEMICAL CHARACTERIZATION OF CARBON NANOSPIKE THIN FILM ELECTRODES Citation Details In-Document Search Title: GROWTH AND ELECTROCHEMICAL CHARACTERIZATION OF CARBON NANOSPIKE THIN FILM ELECTRODES Authors: Sheridan, Leah B [1] ; Hensley, Dale K [1] ; Lavrik, Nickolay V [1] ; Smith, Sean C [1] ; Schwartz, Viviane [1] ; Liang, Chengdu [1] ; Rondinone, Adam Justin [1] + Show Author Affiliations ORNL Publication Date: 2014-01-01 OSTI

  12. Growth Mode and Substrate Symmetry Dependent Strain in Epitaxial Graphene.

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Growth Mode and Substrate Symmetry Dependent Strain in Epitaxial Graphene. Citation Details In-Document Search Title: Growth Mode and Substrate Symmetry Dependent Strain in Epitaxial Graphene. Abstract not provided. Authors: Ohta, Taisuke ; Biedermann, Laura Butler ; Beechem Iii, Thomas Edwin ; Howell, Stephen Wayne ; Schmidt, Diedrich A. Publication Date: 2010-06-01 OSTI Identifier: 1123545 Report Number(s): SAND2010-3581J 492436 DOE Contract Number:

  13. Photosynthesis and Biomass Growth (7 Activities) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Photosynthesis and Biomass Growth (7 Activities) Photosynthesis and Biomass Growth (7 Activities) Below is information about the student activity/lesson plan from your search. Grades 9-12 Subject Bioenergy Summary Introduce your students to the power of plants! Photosynthesis is arguably the most important form of energy transformation and is a fundamental concept for students of all ages. Projects listed in this section should be used as an exciting starting point for both classroom and science

  14. Crystallographic evidence for simultaneous growth in graphic granite

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Journal Article: Crystallographic evidence for simultaneous growth in graphic granite Citation Details In-Document Search Title: Crystallographic evidence for simultaneous growth in graphic granite Authors: Xu, Haijun ; Zhang, Junfeng ; Yu, Tony ; Rivers, Mark ; Wang, Yanbin ; Zhao, Shanrong [1] ; UC) [2] + Show Author Affiliations (China U. Geo.) ( Publication Date: 2015-08-21 OSTI Identifier: 1178828 Resource Type: Journal Article Resource Relation:

  15. Growth morphology and properties of metals on graphene (Journal Article) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect SciTech Connect Search Results Journal Article: Growth morphology and properties of metals on graphene Citation Details In-Document Search This content will become publicly available on December 1, 2016 Title: Growth morphology and properties of metals on graphene Graphene, a single atomic layer of graphite, has been the focus of recent intensive studies due to its novel electronic and structural properties. With this study, metals grown on graphene also have been of interest

  16. Technological Advancements Paving the Way for Geothermal Growth |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Technological Advancements Paving the Way for Geothermal Growth Technological Advancements Paving the Way for Geothermal Growth February 12, 2013 - 2:47pm Addthis Preliminary results show an increase in 2012 year-end geothermal capacity Washington, D.C. (Geothermal Energy Association) - As the Geothermal Energy Association (GEA) prepares to release its annual development report at the State of the Geothermal Energy Industry Briefing on February 26 in Washington,

  17. Technology Transfer: Triggering New Global Markets and Job Growth |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Transfer: Triggering New Global Markets and Job Growth Technology Transfer: Triggering New Global Markets and Job Growth September 20, 2011 - 11:33am Addthis The Global Positioning System (GPS) was initially a government technology developed to guide nuclear missiles, and is one of the many examples of the economic potential of successful technology transfer -- the now worldwide location technologies market is projected to grow to $75 billion by 2013. The Global

  18. NREL Growth Forum Brings Together Clean Energy Innovators - News Releases |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL Growth Forum Brings Together Clean Energy Innovators Event recognizes the top startup businesses and clean energy technologies November 5, 2015 The Industry Growth Forum, hosted by the Energy Department's National Renewable Energy Laboratory (NREL), this week attracted more than 400 investors, entrepreneurs, technologists and thought leaders to Denver. At the conclusion of the event three companies were honored with Best Venture and Outstanding Venture Awards. The two-day forum

  19. NREL's Industry Growth Forum Brings Together Energy Innovators - News

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Releases | NREL NREL's Industry Growth Forum Brings Together Energy Innovators Event Highlights Clean Energy Technologies and Startup Businesses November 10, 2011 The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) 24th Industry Growth Forum this week attracted more than 500 investors, entrepreneurs, scientists and policymakers to Denver. The three-day forum highlighted clean energy industry technology and business developments. As part of the forum, NREL also hosted

  20. NREL's Industry Growth Forum Brings Together Energy Innovators - News

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Releases | NREL NREL's Industry Growth Forum Brings Together Energy Innovators Event recognizes the top clean energy technologies and startup businesses October 30, 2014 The Industry Growth Forum hosted by the Energy Department's National Renewable Energy Laboratory (NREL) this week attracted nearly 400 investors, entrepreneurs, scientists and thought leaders to Denver. Last night, three companies where honored with Best Venture and Outstanding Venture Awards. The two-day forum highlighted

  1. Crystal nucleation and near-epitaxial growth in nacre

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Crystal nucleation and near-epitaxial growth in nacre Crystal nucleation and near-epitaxial growth in nacre Print Thursday, 12 December 2013 13:56 Nacre--the iridescent inner lining of many mollusk shells-- has a unique strcuture that is remarkably resistant to fracture. The nacre featured on this cover is from Haliotis laevigata with average layer thickness 470-nm. The colors represent crystal orientationthe crystal lattice tilts across tablets.left stack all tablets are yellow, hence all

  2. ALS Technique Gives Novel View of Lithium Battery Dendrite Growth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ALS Technique Gives Novel View of Lithium Battery Dendrite Growth ALS Technique Gives Novel View of Lithium Battery Dendrite Growth Print Thursday, 24 April 2014 09:46 Lithium-ion batteries, popular in today's electronic devices and electric vehicles, could gain significant energy density if their graphite anodes were replaced with lithium metal anodes. But there's a major concern with substituting lithium-when the battery cycles, microscopic fibers of the lithium anodes ("dendrites")

  3. Improved Growth of High-Temperature Superconductors with HF Pressure

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Control - Energy Innovation Portal Electricity Transmission Electricity Transmission Find More Like This Return to Search Improved Growth of High-Temperature Superconductors with HF Pressure Control Brookhaven National Laboratory Contact BNL About This Technology Publications: PDF Document Publication A new method of HF control for synthesizing YBCO using the BaF2 ex situ process (83 KB) Graphical representation of the removal of hydrogen fluoride gas by the absorber during growth of

  4. Synthesis of segmented silica rods by growth temperature regulation

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect segmented silica rods by growth temperature regulation Citation Details In-Document Search Title: Synthesis of segmented silica rods by growth temperature regulation Authors: Sharma, Jaswinder K [1] ; Datskos, Panos G [1] + Show Author Affiliations ORNL Publication Date: 2014-01-01 OSTI Identifier: 1115377 DOE Contract Number: DE-AC05-00OR22725 Resource Type: Journal Article Resource Relation: Journal Name: Angewandte Chemie International Edition; Journal

  5. The origins of growth stresses in amorphous semiconductor thin films.

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Journal Article: The origins of growth stresses in amorphous semiconductor thin films. Citation Details In-Document Search Title: The origins of growth stresses in amorphous semiconductor thin films. No abstract prepared. Authors: Kotula, Paul Gabriel ; Srolovitz, David J. [1] ; Floro, Jerrold Anthony ; Seel, Steven Craig + Show Author Affiliations (Princeton University, Princeton, NJ) Publication Date: 2003-03-01 OSTI Identifier: 917484 Report Number(s):

  6. Three Regional Partnerships Target Technology Commercialization, Job Growth

    Energy Savers [EERE]

    | Department of Energy Three Regional Partnerships Target Technology Commercialization, Job Growth Three Regional Partnerships Target Technology Commercialization, Job Growth October 14, 2011 - 6:03pm Addthis Dr. Thomas O’Neal of the University of Central Florida at Optigrate, a manufacturer of optical electronic components. Both the university and manufacturer are part of the Igniting Innovation Cleantech Acceleration Network. Dr. Thomas O'Neal of the University of Central Florida at

  7. Home Performance with ENERGY STAR -- 10 Years of Continued Growth! |

    Energy Savers [EERE]

    Department of Energy with ENERGY STAR -- 10 Years of Continued Growth! Home Performance with ENERGY STAR -- 10 Years of Continued Growth! Provides an overview of the HPwES program, HPwES successes, and information on how to become a HPwES sponsor. PDF icon Home Performance with ENERGY STAR Presentation More Documents & Publications Home Performance with Energy Star Home Performance with ENERGY STAR - 2014 BTO Peer Review Residential Building Audits and Retrofits

  8. Forest County Potawatomi Tribe Cuts Emissions, Promotes Green Growth |

    Office of Environmental Management (EM)

    Department of Energy Tribe Cuts Emissions, Promotes Green Growth Forest County Potawatomi Tribe Cuts Emissions, Promotes Green Growth February 23, 2012 - 6:29pm Addthis The Forest County Potawatomi Tribe's solar system is providing heating, cooling, and electricity to the Tribe's administration building in Milwaukee, Wisconsin. Photo from the Forest County Potawatomi Tribe. The Forest County Potawatomi Tribe's solar system is providing heating, cooling, and electricity to the Tribe's

  9. Innovation Ecosystems Spur Rapid Growth for Startups, Entrepreneurs |

    Office of Environmental Management (EM)

    Department of Energy Innovation Ecosystems Spur Rapid Growth for Startups, Entrepreneurs Innovation Ecosystems Spur Rapid Growth for Startups, Entrepreneurs September 14, 2011 - 4:22pm Addthis Rich Earley, CEO of Clean Urban Energy presents at Clean Energy Trust's Clean Energy Challenge in March 2011 | Courtesy of Clean Energy Trust Rich Earley, CEO of Clean Urban Energy presents at Clean Energy Trust's Clean Energy Challenge in March 2011 | Courtesy of Clean Energy Trust Sarah Jane Maxted

  10. New York State 2009 NHTS Comparison Report

    SciTech Connect (OSTI)

    Southworth, Frank; Reuscher, Tim; Hwang, Ho-Ling

    2012-06-01

    The U.S. Department of Transportation (USDOT) initiated an effort in 1969 to collect detailed data on personal travel, with the most recent surveys being the 1995 Nationwide Personal Transportation Survey (NPTS) and the 2001 and 2009 National Household Travel Surveys (NHTS). The primary objective of these surveys is to collect trip-based data on the nature and characteristics of personal travel so that the relationships between the characteristics of personal travel and the socio-economic and demographic characteristics of the traveler and his/her household can be established. In addition to the number of sample households that the national NPTS/NHTS survey allotted to New York State, NYDOT procured an additional sample of households in the 1995, 2001, and 2009 surveys. The comparisons drawn in this report compare the results from these NYS sampled households to the results from households drawn for the rest of the nation. Many of the differences between NYC counties and others in the state result from the striking differences in private vehicle ownership levels, with less than one in two NYC drivers and only 64% of NYC households owning a vehicle in 2009: versus 9 out of 10 drivers owning a vehicle, and between 1.5 and 2 vehicles owned per household, on the average, in the state's other metro areas. And this situation has changed very little over the past fourteen years covered by the three latest NPTS/NHTS surveys. While households in metro areas outside NYC do not own a vehicle largely due to income constraints, many households in NYC/Manhattan do not own a vehicle by choice. However, the statistics suggest that the mobility of zero-vehicle households in NYC/Manhattan is by no means deterred by the lack of a vehicle. While the private vehicle tripmaking rate of NYC residents was between one half and one third that in the state's other metro areas, and their daily VMT about half that of other metro areas, most of their daily travel needs were met by walking or by public transit. As a result, their daily trip-making rates remain consistent with those of vehicle-owning households when all modes of travel are considered. This again indicates that owning a vehicle or being a driver in NYC was less important for meeting a household's mobility needs than anywhere else in NYS. The high levels of public transit usage within NYC replace a great deal of automobile use, and this plus greater use of walk trips results in significantly lower travel generated carbon dioxide emissions per household in NYC than elsewhere in the state. In contrast, the comparatively limited level of public transit ridership in the state's smaller and medium sized metro areas places a much greater reliance on the privately owned vehicle, be it an automobile or the increasingly popular SUV.

  11. Well constructions with inhibited microbial growth and methods of antimicrobial treatment in wells

    DOE Patents [OSTI]

    Lee, Brady D.; Dooley, Kirk J.

    2004-11-02

    The invention includes methods of inhibiting microbial growth in a well. A packing material containing a mixture of a first material and an antimicrobial agent is provided to at least partially fill a well bore. One or more access tubes are provided in an annular space around a casing within the well bore. The access tubes have a first terminal opening located at or above a ground surface and have a length that extends from the first terminal opening at least part of the depth of the well bore. The access tubes have a second terminal opening located within the well bore. An antimicrobial material is supplied into the well bore through the first terminal opening of the access tubes. The invention also includes well constructs.

  12. Stochastic Boundary, Diffusion, Emittance Growth and Lifetime calculation for the RHIC e-lens

    SciTech Connect (OSTI)

    Abreu,N.P.; Fischer, W.; Luo, Y.; Robert-Demolaize, G.

    2009-01-20

    To compensate the large tune shift and tune spread generated by the head-on beam-beam interactions in polarized proton operation in the Relativistic Heavy Ion Collider (RHIC), a low energy electron beam with proper Gaussian transverse profiles was proposed to collide head-on with the proton beam. In this article, using a modified version of SixTrack [1], we investigate stability of the single particle in the presence of head-on beam-beam compensation. The Lyapunov exponent and action diffusion are calculated and compared between the cases without and with beam-beam compensation for two different working points and various bunch intensities. Using the action diffusion results the emittance growth rate and lifetime of the proton beam is also estimated for the different scenarios.

  13. Hydrogen Production: Fundamentals and Case Study Summaries (Presentation)

    SciTech Connect (OSTI)

    Harrison, K.; Remick, R.; Hoskin, A.; Martin, G.

    2010-05-19

    This presentation summarizes hydrogen production fundamentals and case studies, including hydrogen to wind case studies.

  14. A comparison of parametric decay of oblique Langmuir wave in high and low density magneto-plasmas

    SciTech Connect (OSTI)

    Shahid, M.; Hussain, A.; Department of Physics, Government College University, Lahore-54000 ; Murtaza, G.

    2013-09-15

    The parametric decay instability of an obliquely propagating Langmuir wave into the low-frequency electromagnetic shear Alfven wave and the Left-Handed Circularly Polarized wave has been investigated in an electron-ion plasma, immersed in a uniform external magnetic field. Quantum magneto-hydrodynamic model has been used to find the linear and non-linear response of a high density quantum magneto-plasma. Going to the classical limit (??0) retrieves the results for low density classical plasma. Nonlinear dispersion relations and growth rates are derived with analytically and numerically. It is observed that growth rate in the high density degenerate magneto-plasma increases exponentially, while in the low density classical case it increases logarithmically.

  15. Are shorted pipeline casings a problem

    SciTech Connect (OSTI)

    Gibson, W.F. )

    1994-11-01

    The pipeline industry has many road and railroad crossings with casings which have been in service for more than 50 years without exhibiting any major problems, regardless of whether the casing is shorted to or isolated from the carrier pipe. The use of smart pigging and continual visual inspection when retrieving a cased pipeline segment have shown that whether shorted or isolated, casings have no significant bearing on the presence or absence of corrosion on the carrier pipe.

  16. Federal Utility Energy Service Contract Case Studies

    Broader source: Energy.gov [DOE]

    These case studies feature examples of federal projects made possible by the use of utility energy service contracts (UESCs).

  17. Federal Energy Savings Performance Contract Case Studies

    Broader source: Energy.gov [DOE]

    These case studies feature examples of projects made possible by the use of energy savings performance contracts (ESPCs).

  18. Influence of CO sub 2 -HCO sub 3 sup minus levels and pH on growth, succinate production, and enzyme activities of Anaerobiospirillum succiniciproducens

    SciTech Connect (OSTI)

    Samuelov, N.S.; Lamed, R.; Lowe, S. ); Zeikus, J.G. Michigan Biotechnology Inst., Lansing )

    1991-10-01

    Growth and succinate versus lactate production from glucose by Anaerobiospirillum succiniciproducens was regulated by the level of available carbon dioxide and culture pH. At pH 7.2, the generation time was almost doubled and extensive amounts of lactate were formed in comparison with growth at pH 6.2. The succinate yield and the yield of ATP per mole of glucose were significantly enhanced under excess-CO{sub 2}-HOC{sub 3}{sup {minus}} growth conditions and suggest that there exists a threshold level of Co{sub 2} for enhanced succinate production in A. succiniciproducens. Glucose was metabolized via the Embden-Meyerhof-Parnas route, and phosphoenopyruvate carboxykinase levels increased while lactate dehydrogenase and alcohol dehydrogenase levels decreased under excess-CO{sub 2}-HCO{sub 3}{sup {minus}} growth conditions. Kinetic analysis of succinate and lactate formation in continuous culture indicated that the growth rate-linked production rate coefficient (K) cells was much higher for succinate (7.2 versus 1.0 g/g of cells per h) while the non-growth-rate-related formation rate coefficient (K{prime}) was higher for lactate (1.1 versus 0.3 g/g of cells per h). The data indicate that A. succiniciproducens, unlike other succinate-producing anaerobes which also form propionate, can grow rapidly and form high final yields of succinate at pH 6.2 and with excess CO{sub 2}-HCO{sub 3}{sup {minus}} as a consequence of regulating electron sink metabolism.

  19. Comparison of AEO 2006 Natural Gas Price Forecast to NYMEX FuturesPrices

    SciTech Connect (OSTI)

    Bolinger, Mark; Wiser, Ryan

    2005-12-19

    On December 12, 2005, the reference case projections from ''Annual Energy Outlook 2006'' (AEO 2006) were posted on the Energy Information Administration's (EIA) web site. We at LBNL have in the past compared the EIA's reference case long-term natural gas price forecasts from the AEO series to contemporaneous natural gas prices that can be locked in through the forward market, with the goal of better understanding fuel price risk and the role that renewables play in mitigating such risk (see, for example, http://eetd.lbl.gov/ea/EMS/reports/53587.pdf or http://eetd.lbl.gov/ea/ems/reports/54751.pdf). As such, we were curious to see how the latest AEO gas price forecast compares to the NYMEX natural gas futures strip. This brief memo presents our findings. As a refresher, our past work in this area has found that over the past five years, forward natural gas contracts (with prices that can be locked in--e.g., gas futures, swaps, and physical supply) have traded at a premium relative to contemporaneous long-term reference case gas price forecasts from the EIA. As such, we have concluded that, over the past five years at least, levelized cost comparisons of fixed-price renewable generation with variable price gas-fired generation that have been based on AEO natural gas price forecasts (rather than forward prices) have yielded results that are ''biased'' in favor of gas-fired generation, presuming that long-term price stability is valued. In this memo we simply update our past analysis to include the latest long-term gas price forecast from the EIA, as contained in AEO 2006. For the sake of brevity, we do not rehash information (on methodology, potential explanations for the premiums, etc.) contained in our earlier reports on this topic; readers interested in such information are encouraged to download that work from http://eetd.lbl.gov/ea/EMS/reports/53587.pdf or http://eetd.lbl.gov/ea/ems/reports/54751.pdf. As was the case in the past five AEO releases (AEO 2001-AEO 2005), we once again find that the AEO 2006 reference case gas price forecast falls well below where NYMEX natural gas futures contracts were trading at the time the EIA finalized its gas price forecast. In fact, the NYMEX-AEO 2006 reference case comparison yields by far the largest premium--$2.3/MMBtu levelized over five years--that we have seen over the last six years. In other words, on average, one would have had to pay $2.3/MMBtu more than the AEO 2006 reference case natural gas price forecast in order to lock in natural gas prices over the coming five years and thereby replicate the price stability provided intrinsically by fixed-price renewable generation (or other forms of generation whose costs are not tied to the price of natural gas). Fixed-price generation (like certain forms of renewable generation) obviously need not bear this added cost, and moreover can provide price stability for terms well in excess of five years.

  20. Comparison of AEO 2005 natural gas price forecast to NYMEX futures prices

    SciTech Connect (OSTI)

    Bolinger, Mark; Wiser, Ryan

    2004-12-13

    On December 9, the reference case projections from ''Annual Energy Outlook 2005 (AEO 2005)'' were posted on the Energy Information Administration's (EIA) web site. As some of you may be aware, we at LBNL have in the past compared the EIA's reference case long-term natural gas price forecasts from the AEO series to contemporaneous natural gas prices that can be locked in through the forward market, with the goal of better understanding fuel price risk and the role that renewables play in mitigating such risk. As such, we were curious to see how the latest AEO gas price forecast compares to the NYMEX natural gas futures strip. This brief memo presents our findings. As a refresher, our past work in this area has found that over the past four years, forward natural gas contracts (e.g., gas futures, swaps, and physical supply) have traded at a premium relative to contemporaneous long-term reference case gas price forecasts from the EIA. As such, we have concluded that, over the past four years at least, levelized cost comparisons of fixed-price renewable generation with variable price gas-fired generation that have been based on AEO natural gas price forecasts (rather than forward prices) have yielded results that are ''biased'' in favor of gas-fired generation (presuming that long-term price stability is valued). In this memo we simply update our past analysis to include the latest long-term gas price forecast from the EIA, as contained in AEO 2005. For the sake of brevity, we do not rehash information (on methodology, potential explanations for the premiums, etc.) contained in our earlier reports on this topic; readers interested in such information are encouraged to download that work from http://eetd.lbl.gov/ea/EMS/reports/53587.pdf or, more recently (and briefly), http://eetd.lbl.gov/ea/ems/reports/54751.pdf. As was the case in the past four AEO releases (AEO 2001-AE0 2004), we once again find that the AEO 2005 reference case gas price forecast falls well below where NYMEX natural gas futures contracts were trading at the time the EIA finalized its gas price forecast. In fact, the NYMEXAEO 2005 reference case comparison yields by far the largest premium--$1.11/MMBtu levelized over six years--that we have seen over the last five years. In other words, on average, one would have to pay $1.11/MMBtu more than the AEO 2005 reference case natural gas price forecast in order to lock in natural gas prices over the coming six years and thereby replicate the price stability provided intrinsically by fixed-price renewable generation. Fixed-price renewables obviously need not bear this added cost, and moreover can provide price stability for terms well in excess of six years.

  1. Spatial growth of the current-driven instability in relativistic jets

    SciTech Connect (OSTI)

    Mizuno, Yosuke; Hardee, Philip E.; Nishikawa, Ken-Ichi

    2014-04-01

    We investigated the influence of velocity shear and a radial density profile on the spatial development of the current-driven (CD) kink instability along helically magnetized relativistic jets via three-dimensional relativistic magnetohydrodynamic simulations. In this study, we use a nonperiodic computational box, the jet flow is initially established across the computational grid, and a precessional perturbation at the inlet triggers growth of the kink instability. If the velocity shear radius is located inside the characteristic radius of the helical magnetic field, a static nonpropagating CD kink is excited as the perturbation propagates down the jet. Temporal growth disrupts the initial flow across the computational grid not too far from the inlet. On the other hand, if the velocity shear radius is outside the characteristic radius of the helical magnetic field, the kink is advected with the flow and grows spatially down the jet. In this case, flow is maintained to much larger distances from the inlet. The effect of different radial density profiles is more subtle. When the density increases with radius, the kink appears to saturate by the end of the simulation without apparent disruption of the helical twist. This behavior suggests that relativistic jets consisting of a tenuous spine surrounded by a denser medium with a velocity shear radius outside the radius of the maximum toroidal magnetic field have a relatively stable configuration.

  2. Japan-Economics of Climate Change and Low Carbon Growth Strategies...

    Open Energy Info (EERE)

    and Low Carbon Growth Strategies in Northeast Asia Jump to: navigation, search Name Japan-Economics of Climate Change and Low Carbon Growth Strategies in Northeast Asia Agency...

  3. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    U.S. Energy Information Administration | International Energy Outlook 2014 38 Appendix B Table B2. World liquids consumption by region, High Oil Price case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2020 2025 2030 2035 2040 OECD OECD Americas 23.1 23.5 23.4 22.9 22.3 22.0 22.0 -0.2 United States a 18.6 18.9 18.6 18.0 17.4 17.2 17.2 -0.3 Canada 2.2 2.2 2.2 2.1 2.0 2.0 1.9 -0.5 Mexico/Chile 2.4 2.4 2.6 2.7 2.8 2.8 2.9 0.6 OECD

  4. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    U.S. Energy Information Administration | International Energy Outlook 2014 50 Appendix C Table C2. World liquids consumption by region, Low Oil Price case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2020 2025 2030 2035 2040 OECD OECD Americas 23.1 23.5 24.8 24.8 24.7 24.9 25.5 0.3 United States a 18.6 18.9 19.6 19.5 19.4 19.4 19.8 0.1 Canada 2.2 2.2 2.4 2.4 2.4 2.5 2.6 0.5 Mexico/Chile 2.4 2.4 2.8 2.9 3.0 3.0 3.2 1.0 OECD Europe

  5. Comparison among Magnus/Floquet/Fer expansion schemes in solid-state NMR

    SciTech Connect (OSTI)

    Takegoshi, K. Miyazawa, Norihiro; Sharma, Kshama; Madhu, P. K.

    2015-04-07

    We here revisit expansion schemes used in nuclear magnetic resonance (NMR) for the calculation of effective Hamiltonians and propagators, namely, Magnus, Floquet, and Fer expansions. While all the expansion schemes are powerful methods there are subtle differences among them. To understand the differences, we performed explicit calculation for heteronuclear dipolar decoupling, cross-polarization, and rotary-resonance experiments in solid-state NMR. As the propagator from the Fer expansion takes the form of a product of sub-propagators, it enables us to appreciate effects of time-evolution under Hamiltonians with different orders separately. While 0th-order average Hamiltonian is the same for the three expansion schemes with the three cases examined, there is a case that the 2nd-order term for the Magnus/Floquet expansion is different from that obtained with the Fer expansion. The difference arises due to the separation of the 0th-order term in the Fer expansion. The separation enables us to appreciate time-evolution under the 0th-order average Hamiltonian, however, for that purpose, we use a so-called left-running Fer expansion. Comparison between the left-running Fer expansion and the Magnus expansion indicates that the sign of the odd orders in Magnus may better be reversed if one would like to consider its effect in order.

  6. Dynamics of laser-induced molecular alignment in the impulsive and adiabatic regimes: A direct comparison

    SciTech Connect (OSTI)

    Torres, R.; Marangos, J.P.; Nalda, R. de

    2005-08-15

    Quantum-mechanical calculations are performed of the dynamic alignment of linear molecules induced by a strong nonresonant laser field. Within this framework we have treated in a unified fashion the alignment with laser pulses of varying duration from the short pulse impulsive limit ({tau}{sub pulse}<T{sub rot}). The temporal behavior of the alignment in both these limits, and in the intermediate pulse duration regime, have been analyzed. For the impulsive limit the dependence of the degree of maximum alignment upon the laser pulse duration was examined and the intensity-dependent optimum pulse duration explained. A comparison between the degree of alignment under the same conditions of pulse intensity and rotational temperature was performed between the impulsive and adiabatic cases. The adiabatic case was found to always provide a better degree of alignment for a given intensity which we show is due to the zero relative phasing between the component states of the superposition that form the pendular states. We have explicitly calculated the angular distribution of an ensemble of linear molecules as it evolves through a rotational revival; a rich structure is found that may be useful in guiding future experiments that utilize the field free alignment in a revival.

  7. Comparison of PWR-IMF and FR fuel cycles

    SciTech Connect (OSTI)

    Darilek, Petr; Zajac, Radoslav; Breza, Juraj |; Necas, Vladimir

    2007-07-01

    The paper gives a comparison of PWR (Russia origin VVER-440) cycle with improved micro-heterogeneous inert matrix fuel assemblies and FR cycle. Micro-heterogeneous combined assembly contains transmutation pins with Pu and MAs from burned uranium reprocessing and standard uranium pins. Cycle analyses were performed by HELIOS spectral code and SCALE code system. Comparison is based on fuel cycle indicators, used in the project RED-IMPACT - part of EU FP6. Advantages of both closed cycles are pointed out. (authors)

  8. Comparison of CNG and LNG technologies for transportation applications

    SciTech Connect (OSTI)

    Sinor, J.E. Consultants, Inc., Niwot, CO )

    1992-01-01

    This report provides a head-to-head comparison of compressed natural gas (CNG) and liquefied natural gas (LNG) supplied to heavy-duty vehicles. The comparison includes an assessment of the overall efficiency of the fuel delivery system, the cost of the fuel supply system, the efficiency of use in heavy-duty vehicles, and the environmental impact of each technology. The report concludes that there are applications in which CNG will have the advantage, and applications in which LNG will be preferred.

  9. Comparison of silatrane, phosphonic acid, and carboxylic acid functional

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    groups for attachment of porphyrin sensitizers to TiO2 in photoelectrochemical cells Comparison of silatrane, phosphonic acid, and carboxylic acid functional groups for attachment of porphyrin sensitizers to TiO2 in photoelectrochemical cells Authors: Brennan, B.J., Llansola Portoles, M.J., Liddell, P.A., Moore, T.A., Moore, A.L., and Gust, D. Title: Comparison of silatrane, phosphonic acid, and carboxylic acid functional groups for attachment of porphyrin sensitizers to TiO2 in

  10. Comparison Table of Department of Energy Mentor-Protege Program |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Programs » Mentor-Protégé Program » Comparison Table of Department of Energy Mentor-Protege Program Comparison Table of Department of Energy Mentor-Protege Program Program/Field Offices and Labs Alliance for Sustainable Energy (NREL) Argonne National Laboratory * DOE Headquarters Fermi National Accelerator Laboratory Los Alamos Nat'l Lab Oak Ridge Institute for Science and Education (ORISE) managed by ORAU Oak Ridge Nat'l Lab Thomas Jefferson Nat'l Accelerator

  11. Technical Approach and Results from the Fuels Pathway on an Alternative Selection Case Study

    SciTech Connect (OSTI)

    Bob Youngblood; Curtis Smith

    2013-09-01

    The report presents a detailed plan for conducting case studies to characterize probabilistic safety margins associated with different fuel cladding types in a way that supports a valid comparison of different fuels' performance. Recent work performed in other programs is described briefly and used to illustrate the challenges posed by characterization of margin in a probabilistic way. It is additionally pointed out that consistency of evaluation of performance across different cladding types is not easy to assure; a process for achieving the needed consistency is described.

  12. Concrete growth problems and remedial measures at TVA projects

    SciTech Connect (OSTI)

    Hammer, J.J.

    1984-01-01

    Most concrete structures are designed and detailed to provide for a volume decrease without excessive cracking. Occasionally, however, a concrete structure exhibits a long-term increase in volume termed concrete growth. Concrete growth may result from a variety of reactions, such as the hydration of unstable oxides included in the concrete mix, or the oxidation of minerals or from an outside attack of sulfates. The most important reaction creating concrete growth is that between minor alkali hydroxides from cement and the concrete aggregates. Two distinctly different harmful reactions have been recognized: the alkali-silicate and alkali-carbonate reactions. Concrete deteriorating from an alkali-aggregate reaction, regardless of the type, develops an obvious network of cracks called pattern or map cracking. These alkali-aggregate reactions and their accompanying concrete growth have presented numerous problems at TVA's Fontana Dam, Chickamauga Dam and lock, and Hiwassee Dam. Much has been learned about alkali-aggregate reaction since 1940. Most harmful reactions can now be prevented in proposed structures by interpreting the results of standard test methods. It is not possible, however, in existing structures to determine how far the growth phenomenon has progressed, how long the effects will have to be dealt with, or what the future effects will be. A program of close surveillance and monitoring is maintained at these projects, and problems are dealt with as they arise.

  13. Mask-assisted seeded growth of segmented metallic heteronanostructures

    SciTech Connect (OSTI)

    Crane, Cameron C.; Tao, Jing; Wang, Feng; Zhu, Yimei; Chen, Jingyi

    2014-11-24

    Controlling the deposition of exotic metals in the seeded growth of multi-metal nanostructures is challenging. This work describes a seeded growth method assisted by a mask for synthesis of segmented binary or ternary metal nanostructures. Silica is used as a mask to partially block the surface of a seed and a second metal is subsequently deposited on the exposed area, forming a bimetallic heterodimer. The initial demonstration was carried out on a Au seed, followed by deposition of Pd or Pt on the seed. It was found that Pd tends to spread out laterally on the seed while Pt inclines to grow vertically into branched topology on Au. Without removal of the SiO? mask, Pt could be further deposited on the unblocked Pd of the Pd-Au dimer to form a Pt-Pd-Au trimer. The mask-assisted seeded growth provides a general strategy to construct segmented metallic nanoarchitectures.

  14. Computer Simulation of Bubble Growth in Metals Due to He

    SciTech Connect (OSTI)

    FOILES, STEPHEN M.; HOYT, JEFFREY J.

    2001-03-01

    Atomistic simulations of the growth of helium bubbles in metals are performed. The metal is represented by embedded atom method potentials for palladium. The helium bubbles are treated via an expanding repulsive spherical potential within the metal lattice. The simulations predict bubble pressures that decrease monotonically with increasing helium to metal ratios. The swelling of the material associated with the bubble growth is also computed. It is found that the rate of swelling increases with increasing helium to metal ratio consistent with experimental observations on the swelling of metal tritides. Finally, the detailed defect structure due to the bubble growth was investigated. Dislocation networks are observed to form that connect the bubbles. Unlike early model assumptions, prismatic loops between the bubbles are not retained. These predictions are compared to available experimental evidence.

  15. Mask-Assisted Seeded Growth of Segmented Metallic Heteronanostructures

    SciTech Connect (OSTI)

    Crane, Cameron C.; Tao, Jing; Wang, Feng; Zhu, Yimei; Chen, Jingyi

    2014-12-04

    Controlling the deposition of exotic metals in the seeded growth of multi-metal nanostructures is challenging. This work describes a seeded growth method assisted by a mask for synthesis of segmented binary or ternary metal nanostructures. Silica is used as a mask to partially block the surface of a seed and a second metal is subsequently deposited on the exposed area, forming a bimetallic heterodimer. The initial demonstration was carried out on a Au seed, followed by deposition of Pd or Pt on the seed. It was found that Pd tends to spread out laterally on the seed while Pt inclines to grow vertically into branched topology on Au. Without removal of the SiO? mask, Pt could be further deposited on the unblocked Pd of the Pd-Au dimer to form a Pt-Pd-Au trimer. The mask-assisted seeded growth provides a general strategy to construct segmented metallic nanoarchitectures.

  16. Growth of and defect reduction in nanoscale materials

    DOE Patents [OSTI]

    Jensen, Kenneth J.; Mickelson, William E.; Zettl, Alex K.

    2011-01-04

    Methods by which the growth of a nanostructure may be precisely controlled by an electrical current are described here. In one embodiment, an interior nanostructure is grown to a predetermined geometry inside another nanostructure, which serves as a reaction chamber. The growth is effected by a catalytic agent loaded with feedstock for the interior nanostructure. Another embodiment allows a preexisting marginal quality nanostructure to be zone refined into a higher-quality nanostructure by driving a catalytic agent down a controlled length of the nanostructure with an electric current. In both embodiments, the speed of nanostructure formation is adjustable, and the growth may be stopped and restarted at will. The catalytic agent may be doped or undoped to produce semiconductor effects, and the bead may be removed via acid etching.

  17. Mask-Assisted Seeded Growth of Segmented Metallic Heteronanostructures

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Crane, Cameron C.; Tao, Jing; Wang, Feng; Zhu, Yimei; Chen, Jingyi

    2014-12-04

    Controlling the deposition of exotic metals in the seeded growth of multi-metal nanostructures is challenging. This work describes a seeded growth method assisted by a mask for synthesis of segmented binary or ternary metal nanostructures. Silica is used as a mask to partially block the surface of a seed and a second metal is subsequently deposited on the exposed area, forming a bimetallic heterodimer. The initial demonstration was carried out on a Au seed, followed by deposition of Pd or Pt on the seed. It was found that Pd tends to spread out laterally on the seed while Pt inclinesmore » to grow vertically into branched topology on Au. Without removal of the SiO₂ mask, Pt could be further deposited on the unblocked Pd of the Pd-Au dimer to form a Pt-Pd-Au trimer. The mask-assisted seeded growth provides a general strategy to construct segmented metallic nanoarchitectures.« less

  18. Predicting crack growth in continuous-fiber composite materials

    SciTech Connect (OSTI)

    Cordes, J.A.; Yazici, R.

    1995-12-31

    Pre-notched composite lamina with unidirectional fibers were studied experimentally and using finite element analysis. Experiments were conducted on notched graphite/aluminum and glass/epoxy panels and the results were compared to a finite element method. Under remote tensile loading, cracks in the graphite/aluminum panels propagated perpendicular to the applied load without stable crack growth. In the glass/epoxy panels, crack propagation was initially stable and parallel to the fibers. A nonlinear damage zone method (DZM) was used to predict the crack growth directions, estimate damages, model stable and unstable crack growths, and predict the loads at failure. For both materials, the predicted loads at failure were within 20% of experimental loads.

  19. Growth of filaments and saturation of the filamentation instability

    SciTech Connect (OSTI)

    Gedalin, M.; Medvedev, M.; Spitkovsky, A.; Krasnoselskikh, V.; Vaivads, A.; Perri, S.

    2010-03-15

    The filamentation instability of counterstreaming beams is a nonresonant hydrodynamic-type instability whose growth rate is a smooth function of the wavelength (scale). As a result, perturbations with all unstable wavelengths develop, and the growth saturates due to the saturation of available current. For a given scale, the magnetic field at saturation is proportional to the scale. As a result, the instability develops in a nearly linear regime, where the unstable modes stop growing as soon as the saturation of the corresponding wavelength is reached. At each moment there exists a dominant scale of the magnetic field which is the scale that reached saturation at this particular time. The smaller scales do not disappear and can be easily distinguished in the current structure. The overall growth of the instability stops when the loss of the streaming ion energy because of deceleration is comparable to the initial ion energy.

  20. Indium Growth and Island Height Control on Si Submonolayer Phases

    SciTech Connect (OSTI)

    Chen, Jizhou

    2009-05-09

    Nanotechnology refers any technique that involves about object with nanoscale (10{sup -9} m) or even smaller. It has become more and more important in recently years and has changed our world dramatically. Most of modern electronic devices today should thanks to the miniaturizing driven by development of nanotechnology. Recent years, more and more governments are investing huge amount of money in research related to nanotechnology. There are two major reasons that nanostructure is so fascinate. The first one is the miniaturizing. It is obvious that if we can make products smaller without losing the features, we can save the cost and increase the performance dramatically. For an example, the first computer in the world, ENIAC, which occupied several rooms, is less powerful than the cheapest calculator today. Today's chips with sizes of less than half an inch contain millions of basic units. All these should thank to the development of nanotechnology. The other reason is that when we come to nanoscale, there are many new effects due to the quantum effect which can't be found in large systems. For an example, quantum dots (QDs) are systems which sizes are below 1{micro}m(10{sup -6}m) and restricted in three dimensions. There are many interesting quantum effects in QDs, including discrete energy levels, and interdot coupling. Due to these properties and their small sizes, QDs have varies potential applications such as quantum computing, probe, light emitting device, solar cells, and laser. To meet the requirement of the nanoelectrical applications, the QDs must be grown highly uniformly because their property is highly dependent on their sizes. The major methods to grow uniform QDs include epitaxial, and lithograph. Lithography is a process to make patterns on a thin film by selectively removing certain parts of the film. Using this method, people have good control over size, location and spacing of QDs. For an example, the Extreme ultraviolet lithography (EUVL) have a wave length of 13.4nm so it can curve on the surface of an sample to make structure as small as the order of 10nm. however, lithograph usually causes permanent damages to the surface and in many cases the QDs are damaged during the lithograph and therefore result in high percentage of defects. Quantum size effect has attracted more and more interests in surface science due to many of its effects. One of its effects is the height preference in film growing and the resulting possibility of uniformly sized self-assemble nanostructure. The experiment of Pb islands on In 4x1 phase shows that both the height and the width can be controlled by proper growth conditions, which expands the growth dimensions from 1 to 2. This discover leads us to study the In/Pb interface. In Ch.3, we found that the Pb islands growing on In 4x1-Si(111) surface which have uniform height due to QSE and uniform width due to the constriction of In 4x1 lattice have unexpected stability. These islands are stable in even RT, unlike usual nanostructures on Pb/Si surface which are stable only at low temperature. Since similar structures are usually grown at low temperature, this discovery makes the grown structures closer to technological applications. It also shows the unusual of In/Pb interface. Then we studied the In islands grown on Pb-{alpha}-{radical}3x{radical}3-Si(111) phase in Ch.4. These islands have fcc structure in the first few layers, and then convert to bct structure. The In fcc islands have sharp height preference due to QSE like Pb islands. However, the preferred height is different (7 layer for Pb on Si 7x7 and 4 layer for Pb on In 4x1), due to the difference of interface. The In islands structure prefers to be bct than fcc with coverage increase. It is quantitatively supported by first-principle calculation. Unexpectedly, the In islands grown on various of In interfaces didn't show QSE effects and phase transition from fcc and bct structures as on the Pb-{alpha} interface (Ch.6). In g(s) curve there is no clear oscillations in the g(s) curve as the In on Pb-{alpha} phase. This

  1. Expression of transforming growth factor alpha in plutonium-239-induced lung neoplasms in dogs: investigations of autocrine mechanisms of growth

    SciTech Connect (OSTI)

    Gillett, N.A.; Stegelmeier, B.L.; Chang, I.Y.; Kelly, G. )

    1991-06-01

    We have previously shown that 47% of radiation-induced lung neoplasms in dogs exhibit increased expression of epidermal growth factor receptor (EGFR). In this study, we investigated the expression of transforming growth factor alpha (TGF-alpha), a ligand for EGFR, to determine if an autocrine mechanism for growth stimulation was present in these tumors. As determined by immunohistochemistry, 59% (26/44) of the lung neoplasms examined had increased expression of TGF-alpha. Expression of TGF-alpha was not related to the etiology of the tumor, e.g., spontaneous or plutonium-induced; however, it was related to the phenotype of the tumor. Statistical analysis of the correlation of EGFR and TGF-alpha expression within the same tumor did not show a positive association; however, specific phenotypes did have statistically significant expression of EGFR or TGF-alpha, suggesting that overexpression of either the ligand or its receptor conferred a growth advantage to the neoplasm. Twenty-seven percent (32/117) of radiation-induced proliferative epithelial foci expressed TGF-alpha, and a portion of those foci (8/32) expressed both EGFR and TGF-alpha. This supports the hypothesis that these foci represent preneoplastic lesions, and suggests that those foci exhibiting increased expression of the growth factor or its receptor are at greater risk for progressing to neoplasia.

  2. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    44 Appendix B Table B5. World crude and lease condensate a production by region and country, High Oil Price case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030 2035 2040 OPEC b 31.0 32.0 32.2 28.5 29.6 32.5 35.2 37.9 0.6 Middle East 20.8 21.7 23.0 19.1 19.9 22.6 25.2 27.5 0.8 North Africa 3.3 3.2 2.0 2.6 2.6 2.7 2.7 2.7 -0.6 West Africa 4.1 4.4 4.3 4.3 4.5 4.6 4.8 4.8 0.3 South America 2.8 2.7 2.8 2.5 2.5 2.5 2.6

  3. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    6 Appendix C Table C5. World crude and lease condensate a production by region and country, Low Oil Price case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030 2035 2040 OPEC b 31.0 32.0 32.2 39.0 44.2 49.9 54.8 60.2 2.1 Middle East 20.8 21.7 23.0 27.1 31.0 35.3 39.3 43.6 2.3 North Africa 3.3 3.2 2.0 3.2 3.4 3.6 3.8 4.1 0.8 West Africa 4.1 4.4 4.3 5.4 6.0 6.7 7.0 7.3 1.7 South America 2.8 2.7 2.8 3.3 3.7 4.2 4.6

  4. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    26 Appendix A Table A2. World liquids consumption by region, Reference case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2020 2025 2030 2035 2040 OECD OECD Americas 23.1 23.5 24.3 24.0 23.6 23.4 23.5 0.0 United States a 18.6 18.9 19.2 19.0 18.6 18.5 18.4 -0.1 Canada 2.2 2.2 2.3 2.2 2.2 2.2 2.1 -0.1 Mexico/Chile 2.4 2.4 2.7 2.8 2.8 2.8 2.9 0.7 OECD Europe 15.0 14.8 14.1 14.1 14.0 13.9 14.0 -0.2 OECD Asia 7.7 7.7 8.0 7.9 7.7 7.4 7.2

  5. Appendix A. Reference case projections

    Gasoline and Diesel Fuel Update (EIA)

    2 Appendix A Table A5. World crude and lease condensate a production by region and country, Reference case, 2009-40 (million barrels per day) Region History Projections Average annual percent change, 2010-40 2009 2010 2011 2020 2025 2030 2035 2040 OPEC b 31.0 32.0 32.2 34.4 36.1 39.5 42.9 46.2 1.2 Middle East 20.8 21.7 23.0 23.8 25.2 28.4 31.5 34.5 1.6 North Africa 3.3 3.2 2.0 2.9 2.9 2.9 2.9 3.0 -0.3 West Africa 4.1 4.4 4.3 4.9 5.0 5.1 5.2 5.3 0.6 South America 2.8 2.7 2.8 2.9 2.9 3.0 3.2 3.5

  6. Material and methods to increase plant growth and yield

    DOE Patents [OSTI]

    Kirst, Matias

    2015-09-15

    The present invention relates to materials and methods for modulating growth rates, yield, and/or resistance to drought conditions in plants. In one embodiment, a method of the invention comprises increasing expression of an hc1 gene (or a homolog thereof that provides for substantially the same activity), or increasing expression or activity of the protein encoded by an hc1 gene thereof, in a plant, wherein expression of the hc1 gene or expression or activity of the protein encoded by an hc1 gene results in increased growth rate, yield, and/or drought resistance in the plant.

  7. Epitaxial Growth of Strontium Bismuth Tantalate/Niobate of Buffered

    Office of Scientific and Technical Information (OSTI)

    Magnesium Oxide Substrates (Conference) | SciTech Connect Conference: Epitaxial Growth of Strontium Bismuth Tantalate/Niobate of Buffered Magnesium Oxide Substrates Citation Details In-Document Search Title: Epitaxial Growth of Strontium Bismuth Tantalate/Niobate of Buffered Magnesium Oxide Substrates Epitaxial films of strontium bismuth tantalate (SrBi{sub 2}Ta{sub 2}O{sub 9}, SBT) and strontium bismuth niobate (SrBi{sub 2}Nb{sub 2}O{sub 9}, SBN) were grown using solution deposition

  8. Branching Mechanisms in Surfactant Micellar Growth (Journal Article) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Journal Article: Branching Mechanisms in Surfactant Micellar Growth Citation Details In-Document Search Title: Branching Mechanisms in Surfactant Micellar Growth Authors: Tang, M ; Carter, W C Publication Date: 2012-08-20 OSTI Identifier: 1169255 Report Number(s): LLNL-JRNL-575474 DOE Contract Number: DE-AC52-07NA27344 Resource Type: Journal Article Resource Relation: Journal Name: Journal of Physical Chemistry B, na, na, March 14, 2013, pp. 2898 Research Org: Lawrence

  9. New DOE Report Reveals Significant Growth in Distributed Wind | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Reveals Significant Growth in Distributed Wind New DOE Report Reveals Significant Growth in Distributed Wind August 1, 2013 - 2:25pm Addthis This is an excerpt from the Second Quarter 2013 edition of the Wind Program R&D Newsletter. Washington, D.C.-This August, the U.S. Department of Energy (DOE) released the first annual market report on wind technologies used in distributed applications compiled through a collaborative effort by DOE's Pacific Northwest National Laboratory,

  10. III-V Growth on Silicon Toward a Multijunction Cell

    SciTech Connect (OSTI)

    Geisz, J.; Olson, J.; McMahon, W.; Friedman, D.; Kibbler, A.; Kramer, C.; Young, M.; Duda, A.; Ward, S.; Ptak, A.; Kurtz, S.; Wanlass, M.; Ahrenkiel, P.; Jiang, C. S.; Moutinho, H.; Norman, A.; Jones, K.; Romero, M.; Reedy, B.

    2005-11-01

    A III-V on Si multijunction solar cell promises high efficiency at relatively low cost. The challenges to epitaxial growth of high-quality III-Vs on Si, though, are extensive. Lattice-matched (LM) dilute-nitride GaNPAs solar cells have been grown on Si, but their performance is limited by defects related to the nitrogen. Advances in the growth of lattice-mismatched (LMM) materials make more traditional III-Vs, such as GaInP and GaAsP, very attractive for use in multijunction solar cells on silicon.

  11. Crystal growth and annealing for minimized residual stress

    DOE Patents [OSTI]

    Gianoulakis, Steven E.

    2002-01-01

    A method and apparatus for producing crystals that minimizes birefringence even at large crystal sizes, and is suitable for production of CaF.sub.2 crystals. The method of the present invention comprises annealing a crystal by maintaining a minimal temperature gradient in the crystal while slowly reducing the bulk temperature of the crystal. An apparatus according to the present invention includes a thermal control system added to a crystal growth and annealing apparatus, wherein the thermal control system allows a temperature gradient during crystal growth but minimizes the temperature gradient during crystal annealing.

  12. Aggregated Purchasing and Workplace Charging Can Drive EV Market Growth |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Aggregated Purchasing and Workplace Charging Can Drive EV Market Growth Aggregated Purchasing and Workplace Charging Can Drive EV Market Growth November 24, 2014 - 11:06am Addthis Secretary of Energy Ernest Moniz with the utility industry's first plug-in electric hybrid drivetrain Class 5 bucket truck at the White House event on November 18, 2014. The truck, which is owned by Pacific Gas and Electric (PG&E), features up to 40 miles of all-electric range and

  13. Fun Fact Friday: Fueling Growth | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fun Fact Friday: Fueling Growth Fun Fact Friday: Fueling Growth January 3, 2014 - 1:53pm Addthis Fuel cells, which work like batteries but don’t run down or need recharging, are ideal for powering material handling equipment, like forklifts and airport baggage carts, because they reduce recharging time and cut carbon pollution. Recent Energy Department reports indicate the fuel cell and hydrogen industry is continuing to grow. | Photo courtesy of Plug Power, Inc. Fuel cells, which work like

  14. Wind Farm Growth Through the Years | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Farm Growth Through the Years Wind Farm Growth Through the Years August 6, 2013 - 8:32am Addthis 1975 Start Slow Stop Year Wind Farms Homes Powered Added Current Year 833 Wind Farms Online. Enough to Power 15 M Homes Data provided by the EIA. The number of homes powered is estimated through conversion factors provided by the EIA. Daniel Wood Daniel Wood Data Visualization and Cartographic Specialist, Office of Public Affairs As we publish the 2012 Wind Technologies Market Report, we are excited

  15. Comparison of JSFR design with EDF requirements for future SFR

    SciTech Connect (OSTI)

    Uematsu, M. M.; Prele, G.; Mariteau, P.; Sauvage, J. F.; Hayafune, H.; Chikazawa, Y.

    2012-07-01

    A comparison of Japan sodium-cooled fast reactor (JSFR) design with future French SFR concept has been done based on the requirement of EDF, the investor-operator of future French SFR, and the French safety baseline, under the framework of EDF-JAEA bilateral agreement of research and development cooperation on future SFR. (authors)

  16. On the formation and origin of substorm growth phase/onset auroral arcs inferred from conjugate space-ground observations

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Motoba, T.; Ohtani, S.; Anderson, B. J.; Korth, H.; Mitchell, D.; Lanzerotti, L. J.; Shiokawa, K.; Connors, M.; Kletzing, C. A.; Reeves, G. D.

    2015-10-27

    In this study, magnetotail processes and structures related to substorm growth phase/onset auroral arcs remain poorly understood mostly due to the lack of adequate observations. In this study we make a comparison between ground-based optical measurements of the premidnight growth phase/onset arcs at subauroral latitudes and magnetically conjugate measurements made by the Active Magnetosphere and Planetary Electrodynamics Response Experiment (AMPERE) at ~780 km in altitude and by the Van Allen Probe B (RBSP-B) spacecraft crossing L values of ~5.0–5.6 in the premidnight inner tail region. The conjugate observations offer a unique opportunity to examine the detailed features of the arcmore » location relative to large-scale Birkeland currents and of the magnetospheric counterpart. Our main findings include (1) at the early stage of the growth phase the quiet auroral arc emerged ~4.3° equatorward of the boundary between the downward Region 2 (R2) and upward Region 1 (R1) currents; (2) shortly before the auroral breakup (poleward auroral expansion) the latitudinal separation between the arc and the R1/R2 demarcation narrowed to ~1.0°; (3) RBSP-B observed a magnetic field signature of a local upward field-aligned current (FAC) connecting the arc with the near-Earth tail when the spacecraft footprint was very close to the arc; and (4) the upward FAC signature was located on the tailward side of a local plasma pressure increase confined near L ~5.2–5.4. These findings strongly suggest that the premidnight arc is connected to highly localized pressure gradients embedded in the near-tail R2 source region via the local upward FAC.« less

  17. On the formation and origin of substorm growth phase/onset auroral arcs inferred from conjugate space-ground observations

    SciTech Connect (OSTI)

    Motoba, T.; Ohtani, S.; Anderson, B. J.; Korth, H.; Mitchell, D.; Lanzerotti, L. J.; Shiokawa, K.; Connors, M.; Kletzing, C. A.; Reeves, G. D.

    2015-10-27

    In this study, magnetotail processes and structures related to substorm growth phase/onset auroral arcs remain poorly understood mostly due to the lack of adequate observations. In this study we make a comparison between ground-based optical measurements of the premidnight growth phase/onset arcs at subauroral latitudes and magnetically conjugate measurements made by the Active Magnetosphere and Planetary Electrodynamics Response Experiment (AMPERE) at ~780 km in altitude and by the Van Allen Probe B (RBSP-B) spacecraft crossing L values of ~5.05.6 in the premidnight inner tail region. The conjugate observations offer a unique opportunity to examine the detailed features of the arc location relative to large-scale Birkeland currents and of the magnetospheric counterpart. Our main findings include (1) at the early stage of the growth phase the quiet auroral arc emerged ~4.3 equatorward of the boundary between the downward Region 2 (R2) and upward Region 1 (R1) currents; (2) shortly before the auroral breakup (poleward auroral expansion) the latitudinal separation between the arc and the R1/R2 demarcation narrowed to ~1.0; (3) RBSP-B observed a magnetic field signature of a local upward field-aligned current (FAC) connecting the arc with the near-Earth tail when the spacecraft footprint was very close to the arc; and (4) the upward FAC signature was located on the tailward side of a local plasma pressure increase confined near L ~5.25.4. These findings strongly suggest that the premidnight arc is connected to highly localized pressure gradients embedded in the near-tail R2 source region via the local upward FAC.

  18. Growth kinetics for the precipitation of zirconium hydroxide from aqueous zirconium and tin bearing solutions by the addition of ammonium hydroxide

    SciTech Connect (OSTI)

    Carleson, T.E.; Chipman, N.A.

    1989-09-11

    The precipitation of zirconium hydroxide from an aqueous solution of ammonium hexafluorozirconate occurs rapidly upon addition of ammonium hydroxide. Experimental data indicate growth and nucleation rates between 0.06 and 0.28 microns/minute and around 10 {times} 107 number/L-min, respectively. Experiments with a mixed suspension mixed product removal crystallizer for concentrations of reactants of about 0.05 M ammonium hexafluorozirconate precipitating with 0.002 M ammonium hydroxide showed apparent nonlinear growth rates in some cases but not others. Batch studies indicated that growth rate dispersion is probably not present. When the AFL nonlinear model was used to fit the data, the power coefficient obtained was greater than 1, in disagreement with theory. In addition, for some of the data ``S`` shaped curves of the logarithm of the cumulative number greater than versus size were obtained. These curves can not be fit by the AFL model. A program developed at the University of Arizona was used to simulate the crystallization runs. The program results indicated that some of the nonlinear behavior may be attributed to transient conditions. Experimental data also illustrated this behavior. The effect of trace amounts of tin fluoride (0.008 M) on the nucleation and growth kinetics was also evaluated. For some residence times, the presence of tin resulted in reduced median particle diameters, higher growth rates, and lower number counts.

  19. Improved Performance of GaInNAs Solar Cells Grown by Molecular-Beam Epitaxy Using Increased Growth Rate Instead of Surfactants

    SciTech Connect (OSTI)

    Ptak, A. J.; France, R.; Jiang, C. S.; Romero, M. J.

    2009-01-01

    GaInNAs is potentially useful for increasing the conversion efficiency of multijunction solar cells if low photocurrents and photovoltages can be increased. Wide-depletion width devices generate significant photocurrents using an n-i-p structure grown by molecular-beam epitaxy, but these wide depletion widths are only realized in a region of parameter space that leads to rough surface morphologies. Surfactants are effective at reducing the surface roughness, but lead to increased defect densities and changes in the net acceptor or donor concentration. Here, we show that increasing the growth rate of GaInNAs solar cells leads to smooth surfaces without the use of a surfactant, even at high In compositions and substrate temperatures. No degradation in material quality is observed when increasing the growth rate from 1.5 to 3.0 {micro}m/h, but a shunt resistance does appear for the high-growth-rate samples. This shunt is attributed to increased spitting of the Ga cell, leading to an increase in the oval defect density, at the higher effusion cell temperatures used to achieve high growth rates. As with the case of Bi in GaInNAs, increased growth rates also appear to increase the net donor concentration, but it is not clear if these effects have the same cause.

  20. Comparison of Joint Modeling Approaches Including Eulerian Sliding...

    Office of Scientific and Technical Information (OSTI)

    In all cases the sliding interfaces are tracked explicitly without homogenization or blending the joint and block response into an average response. In general, rock joints will ...

  1. The inside-out growth of the most massive galaxies at 0.3 < z < 0.9

    SciTech Connect (OSTI)

    Bai, Lei; Yee, H. K. C.; Li, I. H.; Yan, Renbin; Lee, Eve; Gilbank, David G.; Ellingson, E.; Barrientos, L. F.; Gladders, M. D.; Hsieh, B. C.

    2014-07-10

    We study the surface brightness profiles of a sample of brightest cluster galaxies (BCGs) with 0.3 < z < 0.9. The BCGs are selected from the first Red-sequence Cluster Survey and an X-ray cluster survey. The surface brightness profiles of the BCGs are measured using HST ACS images, and the majority of them can be well modeled by a single Srsic profile with a typical Srsic index n ? 6 and a half-light radius ?30 kpc. Although the single Srsic model fits the profiles well, we argue that the systematics in the sky background measurement and the coupling between the model parameters make the comparison of the best-fit model parameters ambiguous. Direct comparison of the BCG profiles, on the other hand, has revealed an inside-out growth for these most massive galaxies: as the mass of a BCG increases, the central mass density of the galaxy increases slowly (?{sub 1kpc}?M{sub ?}{sup 0.39}), while the slope of the outer profile grows continuously shallower (?{sub r{sup 1}{sup /}{sup 4}}?M{sub ?}{sup ?2.5}). Such a fashion of growth continues down to the less massive early-type galaxies (ETGs) as a smooth function of galaxy mass, without apparent distinction between BCGs and non-BCGs. For the very massive ETGs and BCGs, the slope of the Kormendy relation starts to trace the slope of the surface brightness profiles and becomes insensitive to subtle profile evolution. These results are generally consistent with dry mergers being the major driver of the mass growth for BCGs and massive ETGs. We also find strong correlations between the richness of clusters and the properties of BCGs: the more massive the clusters are, the more massive the BCGs (M{sub bcg}{sup ?}?M{sub clusters}{sup 0.6}) and the shallower their surface brightness profiles. After taking into account the bias in the cluster samples, we find the masses of the BCGs have grown by at least a factor of 1.5 from z = 0.5 to z = 0, in contrast to the previous findings of no evolution. Such an evolution validates the expectation from the ?CDM model.

  2. Water Use Reduction Case Studies | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Facilities Water Use Reduction Water Use Reduction Case Studies Water Use Reduction Case Studies These case studies offer examples of water use reduction projects implemented...

  3. WP-07 Power Rate Case (rates/ratecases)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Meetings & Workshops Rate Case Parties Web Site WP-07 Supplemental Rate Case ASC Methodology Adjustments (2007-2009) Adjustments (2002-2006) Previous Rate Cases Financial...

  4. Tribal Case Studies | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tribal Case Studies Tribal Case Studies Below are links to tribal energy project case studies. Financing Community-Scale Clean Energy Projects: Lessons from Project Developers in the Northwest Investigates the challenges developers face in getting clean energy projects financed and provides information on the unique structures, costs, and processes for financing community-scale projects, identifies key challenges and weaknesses in financing, and highlights how developers have creatively financed

  5. Retrofitting Doors on Open Refrigerated Cases

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Retrofitting Doors on Open Refrigerated Cases William Goetzler Navigant Consulting, Inc. wgoetzler@navigant.com (781) 270-8351 April 4, 2013 BBA Refrigeration Project Team Images courtesy of REMIS AMERICA, LLC. 2 | Building Technologies Office eere.energy.gov Technology Overview Image from Investigation of Energy- Efficient Supermarket Display Cases. 2004, Oak Ridge National Laboratory. Background and Motivation * Adding doors to open cases (retrofits) greatly reduces cold air loss - 50-80% load

  6. PNCA-02 Rate Case (rates/ratecases)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Proposed Adjustment to the Rate for Interchange Energy Imbalances Under the Pacific Northwest Coordination Agreement (PNCA-02 Rate Case) (updated on April 26, 2002) BPA has issued...

  7. Building America Technology Solutions Case Study: Combustion...

    Energy Savers [EERE]

    Combustion Safety Simplified Test Protocol Building America Technology Solutions Case Study: Combustion Safety Simplified Test Protocol Two U.S. Department of Energy Building ...

  8. Intercoastal Oil Case No. LEF-0057

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Intercoastal Oil Case No. LEF-0057 file:///C|/Documents%20and%20Settings/blackard/Desktop/MiscCases/lef0057.htm[11/29/2012 2:35:38 PM] Case Nos. LEF-0057 and LEF-0073 September 6, 2001 DECISION AND ORDER DEPARTMENT OF ENERGY Implementation of Special Refund Procedures Names of Firms:Intercoastal Oil Corporation Gulf States Oil & Refining Dates of Filing: July 20, 1993 July 20, 1993 Case Numbers:LEF-0057 LEF-0073 The Office of General Counsel (OGC) of the Department of Energy (DOE) filed a

  9. Multi-facility Workflow Case Study

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Workflow Case Study For one experiment at the Linac Coherent Light Source (LCLS) at SLAC National Lab, scientists needed to process their raw data to analyze catalytic...

  10. Case Study - Compressed Natural Gas Refuse Fleets

    SciTech Connect (OSTI)

    Laughlin, M; Burnham, A.

    2014-02-01

    This case study explores the use of heavy-duty refuse trucks fueled by compressed natural gas highlighting three fleets from very different types of organizations.

  11. A Case Study of Danville Utilities:

    SciTech Connect (OSTI)

    2010-03-09

    This case study provides information on how Danville Utilities utilized ITP Industrial Assessment Centers to provide energy efficiency resources to key accounts.

  12. Better Buildings Residential Network Case Study: Partnerships

    Broader source: Energy.gov [DOE]

    Better Buildings Residential Network Case Study: Partnerships, from the U.S. Department of Energy's Office of Energy Efficiency and Renewable Energy.

  13. Geomechanical modeling of reservoir compaction, surface subsidence, and casing damage at the Belridge diatomite field

    SciTech Connect (OSTI)

    FREDRICH,JOANNE T.; DEITRICK,G.L.; ARGUELLO JR.,JOSE G.; DEROUFFIGNAC,E.P.

    2000-05-01

    Geologic, and historical well failure, production, and injection data were analyzed to guide development of three-dimensional geomechanical models of the Belridge diatomite field, California. The central premise of the numerical simulations is that spatial gradients in pore pressure induced by production and injection in a low permeability reservoir may perturb the local stresses and cause subsurface deformation sufficient to result in well failure. Time-dependent reservoir pressure fields that were calculated from three-dimensional black oil reservoir simulations were coupled uni-directionally to three-dimensional non-linear finite element geomechanical simulations. The reservoir models included nearly 100,000 gridblocks (100--200 wells), and covered nearly 20 years of production and injection. The geomechanical models were meshed from structure maps and contained more than 300,000 nodal points. Shear strain localization along weak bedding planes that causes casing dog-legs in the field was accommodated in the model by contact surfaces located immediately above the reservoir and at two locations in the overburden. The geomechanical simulations are validated by comparison of the predicted surface subsidence with field measurements, and by comparison of predicted deformation with observed casing damage. Additionally, simulations performed for two independently developed areas at South Belridge, Sections 33 and 29, corroborate their different well failure histories. The simulations suggest the three types of casing damage observed, and show that although water injection has mitigated surface subsidence, it can, under some circumstances, increase the lateral gradients in effective stress, that in turn can accelerate subsurface horizontal motions. Geomechanical simulation is an important reservoir management tool that can be used to identify optimal operating policies to mitigate casing damage for existing field developments, and applied to incorporate the effect of well failure potential in economic analyses of alternative infilling and development options.

  14. Residential Electricity Demand in China -- Can Efficiency Reverse the Growth?

    SciTech Connect (OSTI)

    Letschert, Virginie; McNeil, Michael A.; Zhou, Nan

    2009-05-18

    The time when energy-related carbon emissions come overwhelmingly from developed countries is coming to a close. China has already overtaken the United States as the world's leading emitter of greenhouse gas emissions. The economic growth that China has experienced is not expected to slow down significantly in the long term, which implies continued massive growth in energy demand. This paper draws on the extensive expertise from the China Energy Group at LBNL on forecasting energy consumption in China, but adds to it by exploring the dynamics of demand growth for electricity in the residential sector -- and the realistic potential for coping with it through efficiency. This paper forecasts ownership growth of each product using econometric modeling, in combination with historical trends in China. The products considered (refrigerators, air conditioners, fans, washing machines, lighting, standby power, space heaters, and water heating) account for 90percent of household electricity consumption in China. Using this method, we determine the trend and dynamics of demandgrowth and its dependence on macroeconomic drivers at a level of detail not accessible by models of a more aggregate nature. In addition, we present scenarios for reducing residential consumption through efficiency measures defined at the product level. The research takes advantage of an analytical framework developed by LBNL (BUENAS) which integrates end use technology parameters into demand forecasting and stock accounting to produce detailed efficiency scenarios, thus allowing for a technologically realistic assessment of efficiency opportunities specifically in the Chinese context.

  15. Controlled epitaxial graphene growth within removable amorphous carbon corrals

    SciTech Connect (OSTI)

    Palmer, James; Hu, Yike; Hankinson, John; Guo, Zelei; Heer, Walt A. de; Kunc, Jan; Berger, Claire

    2014-07-14

    We address the question of control of the silicon carbide (SiC) steps and terraces under epitaxial graphene on SiC and demonstrate amorphous carbon (aC) corrals as an ideal method to pin SiC surface steps. aC is compatible with graphene growth, structurally stable at high temperatures, and can be removed after graphene growth. For this, aC is first evaporated and patterned on SiC, then annealed in the graphene growth furnace. There at temperatures above 1200?C, mobile SiC steps accumulate at the aC corral that provide effective step flow barriers. Aligned step free regions are thereby formed for subsequent graphene growth at temperatures above 1330?C. Atomic force microscopy imaging supports the formation of step-free terraces on SiC with the step morphology aligned to the aC corrals. Raman spectroscopy indicates the presence of good graphene sheets on the step-free terraces.

  16. Promoting Sustainable Economic Growth in Mexico (Fact Sheet)

    SciTech Connect (OSTI)

    Watson, A.; Butheau, M.; Sandor, D.

    2013-11-01

    Mexico is the second largest economy in Latin America, with rapid growth occurring in the industrial and services sectors. A forward-thinking country on climate change, the nation recognizes that the threat of higher temperatures, changes in precipitation patterns, and more frequent weather-related disasters could pose a substantial risk to its expanding economy.

  17. Environmental management during economic transition: Ukraine--A case study

    SciTech Connect (OSTI)

    Kempen van, T.H.; Demydenko, A.O.

    1995-12-01

    After dissolution of Soviet Union, each new States had to confront the legacy of an unsustainable, and ultimately failed, economic and political system. Enormous environmental problems resulted from centrally planned economics, which promoted rapid growth through exploitation of the former Soviet Union`s (FSU) vast natural resources. Unconstrained by scarcity-based pricing, extractive and heavy industry ministries created huge, inefficient, and heavily polluting enterprises. The region also experienced extensive forest-cutting, steady deterioration of soils, and contaminated runoff and infiltration from over-excessive application of agrichemicals. The fate of the environment will depend largely on successful transition to a market-based economy. Funds for environmental protection will remain scarce, and poor technology combined with a degraded and overworked infrastructure will slow cleanup of contaminated regions. With failed economies, policy-makers and legislators will be forced to overlook sustainable development as they exploit natural resources in an effort to produce food and obtain hard currency. Ukraine, the second-most populous republic of the FSU, experienced possibly the world`s greatest single environment disaster--the 1986 Chernobyl catastrophe. Today, heavy industry, with its resource-intensive and highly polluting technologies, contributes 61% of Ukraine`s GNP, in comparison with 34% in the European Union. Energy production is grossly inefficient. Environmental agencies in Ukraine are new, with limited legal or economic tools, financial resources, or technical skills. Yet the country has commenced environmental management initiatives that, when combined with economic reforms, will start to improve environmental conditions. This paper presents an overview of Ukraine`s environmental and economic conditions, steps already undertaken to manage the environment, and additional measures needed to improve the situation.

  18. Economic Comparison of LNT Versus Urea SCR for Light-Duty Diesel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Comparison of LNT Versus Urea SCR for Light-Duty Diesel Vehicles in the U.S. Market Economic Comparison of LNT Versus Urea SCR for Light-Duty Diesel Vehicles in the U.S. Market ...

  19. SESAM FT-IR: A Comparison of the R&D Workhorse to Standard Emission...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SESAM FT-IR: A Comparison of the R&D Workhorse to Standard Emission Benches SESAM FT-IR: A Comparison of the R&D Workhorse to Standard Emission Benches Data for a number of...

  20. Five case studies of multifamily weatherization programs

    SciTech Connect (OSTI)

    Kinney, L; Wilson, T.; Lewis, G.; MacDonald, M.

    1997-12-31

    The multifamily case studies that are the subject of this report were conducted to provide a better understanding of the approach taken by program operators in weatherizing large buildings. Because of significant variations in building construction and energy systems across the country, five states were selected based on their high level of multifamily weatherization. This report summarizes findings from case studies conducted by multifamily weatherization operations in five cities. The case studies were conducted between January and November 1994. Each of the case studies involved extensive interviews with the staff of weatherization subgrantees conducting multifamily weatherization, the inspection of 4 to 12 buildings weatherized between 1991 and 1993, and the analysis of savings and costs. The case studies focused on innovative techniques which appear to work well.

  1. Grain Growth Behavior, Tensile Impact Ductility, and Weldability of Cerium-Doped Iridium Alloys

    SciTech Connect (OSTI)

    McKamey, C.G.

    2002-05-28

    An iridium alloy doped with small amounts of cerium and thorium is being developed as a potential replacement for the iridium-based DOP-26 alloy (doped with thorium only) that is currently used by the National Aeronautics and Space Administration (NASA) for cladding and post-impact containment of the radioactive fuel in radioisotope thermoelectric generator (RTG) heat sources which provide electric power for interplanetary spacecraft. This report summarizes results of studies conducted to date under the Iridium Alloy Characterization and Development subtask of the Radioisotope Power System Materials Production and Technology Program to characterize the properties of the iridium-based alloy (designated as DOP-40) containing both cerium and thorium. Included within this report are data on grain growth of sheet material in vacuum and low-pressure oxygen environments, grain growth in vacuum of the clad vent set cup material, weldability, and the effect of grain size and test temperature on tensile properties. Where applicable, data for the DOP-26 alloy are included for comparison. Both grain size and grain-boundary cohesion affect the ductility of iridium alloys. In this study it was found that cerium and thorium, when added together, refine grain size more effectively than when thorium is added by itself (especially at high temperatures). In addition, the effect of cerium additions on grain-boundary cohesion is similar to that of thorium. Mechanical testing at both low ({approx} 10{sup -3}s{sup -1}) and high ({approx} 10{sup -3}s{sup -1}) strain rates showed that the Ce/Th-doped alloys have tensile ductilities that are as good or better than the DOP-26 alloy. The general conclusion from these studies is that cerium can be used to replace some of the radioactive thorium currently used in DOP-26 while maintaining or improving its metallurgical properties. The current DOP-26 alloy meets all requirements for cladding the radioactive fuel in the RTG heat source, but the new DOP-40 alloy could serve as a back-up alloy to be used if the costs of refining, handling, and transporting DOP-26 become prohibitively high.

  2. SU-D-19A-07: Dosimetric Comparison of HDR Plesiotherapy and Electron Beam Therapy for Superficial Lesions

    SciTech Connect (OSTI)

    Mitchell, A; Jacob, D; Andreou, K; Raben, A; Chen, H; Koprowski, C; Mourtada, F

    2014-06-01

    Purpose: Large superficial (skin, soft tissue sarcoma) lesions located on curved areas are hard to treat with electrons. The Freiburg Flap (Nucletron, Netherlands) is a flexible mesh style surface which can be easily shaped to fit curved surfaces for reproducible HDR fraction delivery. To understand the fundamental dosimetric differences, a dosimetric comparison was made between HDR plesiotherapy (Freiburg applicator for lesions over 4cm) and external electron beam radiotherapy over cases with varying target curvature (both stylized and clinical cases). Methods: Four stylized cases with variable complexity were created using artificial DICOM axial CT slices and RT structures (a square and three curved structures on a 4.5cm radius cylinder). They were planned using Oncentra v4.3 and exported to Pinnacle v9.6 for electrons planning. The HDR source dwell positions were optimized for the best coverage of the targets using graphical optimization. Electron treatment plans were created in Pinnacle using the same CT and RT structures of three HDR cases with surface lesions previously treated with the Freiburg flap. The En face electron plans used 6-12 MeV electrons and 0.51 cm bolus was added to increase surface dose. The electron plans were prescribed to an isodose line to conform to the target. Results: For all lesions, the average target dose coverage was similar (D90ave of 100% for HDR vs 101% for electrons). For lesions with high curvature, the HDR coverage was better (D90 102% vs D90 97% for electron). For all cases, adjacent structures high dose region was lower for HDR than electrons (D1cc 100% for HDR vs D1cc 111% for electrons). Conclusion: HDR plesiotherapy offers excellent target conformity for superficial targets similar to electrons. However, for lesions with complex curved surfaces, HDR has the advantage to achieve better dose distributions using graphical optimization to spare adjacent normal tissue while maximizing target coverage.

  3. A comparison of cloudiness measures derived from longwave measurements and

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    shortwave sky imagers A comparison of cloudiness measures derived from longwave measurements and shortwave sky imagers Takara, Ezra Florida State University Ellingson, Robert Florida State University Ma, Yingtao University of Maryland Category: Cloud Properties In the longwave, two measures of cloudiness for single layer clouds are the probability of clear line of sight (PCLoS) and the effective cloud fraction. As the name states, the PCLoS is the probability of a clear line of sight through

  4. ARM - Publications: Science Team Meeting Documents: Comparison Study of

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Optical Properties During the Aerosol IOP from Multiple Aircraft Platforms Comparison Study of Optical Properties During the Aerosol IOP from Multiple Aircraft Platforms Hallar, Anna NASA Ames Research Center Strawa, Anthony Ames Research Center Schmid, Beat Bay Area Environmental Research Institute Andrews, Betsy NOAA/CMDL Ogren, John NOAA/CMDL Ferrare, Richard NASA Langley Research Center Covert, David University of Washington Elleman, Robert University of Washington In May 2003, a flight

  5. Aerosol Simulations by LLNL IMPACT and Comparisons with Field Measurements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Simulations by LLNL IMPACT and Comparisons with Field Measurements C. C. Chuang, D. Bergman, J. Dignon, and P. Connell Lawrence Livermore National Laboratory Livermore, California Introduction The first step needed to assess aerosol climate effects is to provide the global concentrations and vertical profiles of different aerosol components. These distributions cannot be easily obtained from satellite retrievals or field measurements but are key to estimating the magnitude of aerosol forcing. A

  6. Comparison of Parameterized Cloud Variability to ARM Data

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Comparison of Parameterized Cloud Variability to ARM Data S. A. Klein National Oceanic and Atmospheric Administration Geophysical Fluid Dynamics Laboratory Princeton, New Jersey J. R. Norris Scripps Institute of Oceanography University of California La Jolla, California Abstract Cloud parameterizations in large-scale models often try to predict the amount of sub-grid scale variability in cloud properties to address the significant non-linear effects of radiation and precipitation. Statistical

  7. Lidar Inter-Comparison Exercise Final Campaign Report A Protat

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lidar Inter-Comparison Exercise Final Campaign Report A Protat S Young February 2015 DOE/SC-ARM-15-008 DISCLAIMER This report was prepared as an account of work sponsored by the U.S. Government. Neither the United States nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use

  8. Characterization and comparison of pore landscapes in crystalline porous

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    materials | Center for Gas SeparationsRelevant to Clean Energy Technologies | Blandine Jerome Characterization and comparison of pore landscapes in crystalline porous materials Previous Next List Marielle Pinheiro, Richard L. Martin, Chris H. Rycroft, Andrew Jones, Enrique Iglesia, Maciej Haranczyk, J. Mol. Graphics Modell., 44, 208-219 (2013) DOI: 10.1016/j.jmgm.2013.05.007 Abstract: Crystalline porous materials have many applications, including catalysis and separations. Identifying

  9. Comparison of Conventional Diesel and Reactivity Controlled Compression

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Ignition (RCCI) Combustion in a Light-Duty Engine | Department of Energy Conventional Diesel and Reactivity Controlled Compression Ignition (RCCI) Combustion in a Light-Duty Engine Comparison of Conventional Diesel and Reactivity Controlled Compression Ignition (RCCI) Combustion in a Light-Duty Engine CFD modeling was used to compare conventional diesel and dual-fuel Reactivity Controlled Compression Ignition combustion at US Tier 2 Bin 5 NOx levels, while accounting for Diesel Exhaust Fluid

  10. Backup Power Cost of Ownership Analysis and Incumbent Technology Comparison

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Backup Power Cost of Ownership Analysis and Incumbent Technology Comparison J. Kurtz, G. Saur, S. Sprik, and C. Ainscough National Renewable Energy Laboratory NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency & Renewable Energy Operated by the Alliance for Sustainable Energy, LLC This report is available at no cost from the National Renewable Energy Laboratory (NREL) at www.nrel.gov/publications. Technical Report NREL/TP-5400-60732 September 2014

  11. Inclusion free cadmium zinc tellurium and cadmium tellurium crystals and associated growth method

    DOE Patents [OSTI]

    Bolotnikov, Aleskey E.; James, Ralph B.

    2010-07-20

    The present disclosure provides systems and methods for crystal growth of cadmium zinc tellurium (CZT) and cadmium tellurium (CdTe) crystals with an inverted growth reactor chamber. The inverted growth reactor chamber enables growth of single, large, high purity CZT and CdTe crystals that can be used, for example, in X-ray and gamma detection, substrates for infrared detectors, or the like. The inverted growth reactor chamber enables reductions in the presence of Te inclusions, which are recognized as an important limiting factor in using CZT or CdTe as radiation detectors. The inverted growth reactor chamber can be utilized with existing crystal growth techniques such as the Bridgman crystal growth mechanism and the like. In an exemplary embodiment, the inverted growth reactor chamber is a U-shaped ampoule.

  12. Multi-frequency optical-depth maps and the case for free-free absorption in two compact symmetric radio sources: The CSO candidate J1324 + 4048 and the CSO J0029 + 3457

    SciTech Connect (OSTI)

    Marr, J. M.; Read, J.; Morris, A. O.; Perry, T. M.; Taylor, G. B.

    2014-01-10

    We obtained dual-polarization very long baseline interferometry observations at six frequencies of the compact symmetric object J0029 + 3457 and the compact symmetric object candidate J1324 + 4048. By comparing the three lower-frequency maps with extrapolations of the high-frequency maps, we produced maps of the optical depth as a function of frequency. The morphology of the optical-depth maps of J1324 + 4048 is strikingly smooth, suggestive of a foreground screen of absorbing gas. The spectra at the intensity peaks fit a simple free-free absorption (FFA) model, with ?{sub ?}{sup 2}?2, better than a simple synchrotron self-absorption model, in which ?{sub ?}{sup 2}?3.5--5.5. We conclude that the case for FFA in J1324 + 4048 is strong. The optical-depth maps of J0029 + 3457 exhibit structure, but the morphology does not correlate with that in the intensity maps. The fit of the spectra at the peaks to a simple FFA model yields ?{sub ?}{sup 2}?1, but because the turnover is gradual, the fit is relatively insensitive to the input parameters. We find that FFA by a thin amount of gas in J0029 + 3457 is likely but not definitive. One compact feature in J0029 + 3457 has an inverted spectrum even at the highest frequencies. We infer this to be the location of the core and estimate an upper limit to the magnetic field of order 3 Gauss at a radius of order 1 pc. In comparison with maps from observations at earlier epochs, no apparent growth in either J1324 + 4048 or J0029 + 3457 is apparent, with upper limits of 0.03 and 0.02 mas yr{sup 1}, corresponding to maximum linear separation speeds of 0.6c and 0.4c.

  13. DIGITAL TECHNOLOGY BUSINESS CASE METHODOLOGY GUIDE & WORKBOOK

    SciTech Connect (OSTI)

    Thomas, Ken; Lawrie, Sean; Hart, Adam; Vlahoplus, Chris

    2014-09-01

    Performance advantages of the new digital technologies are widely acknowledged, but it has proven difficult for utilities to derive business cases for justifying investment in these new capabilities. Lack of a business case is often cited by utilities as a barrier to pursuing wide-scale application of digital technologies to nuclear plant work activities. The decision to move forward with funding usually hinges on demonstrating actual cost reductions that can be credited to budgets and thereby truly reduce O&M or capital costs. Technology enhancements, while enhancing work methods and making work more efficient, often fail to eliminate workload such that it changes overall staffing and material cost requirements. It is critical to demonstrate cost reductions or impacts on non-cost performance objectives in order for the business case to justify investment by nuclear operators. This Business Case Methodology approaches building a business case for a particular technology or suite of technologies by detailing how they impact an operator in one or more of the three following areas: Labor Costs, Non-Labor Costs, and Key Performance Indicators (KPIs). Key to those impacts will be identifying where the savings are harvestable, meaning they result in an actual reduction in headcount and/or cost. The report consists of a Digital Technology Business Case Methodology Guide and an accompanying spreadsheet workbook that will enable the user to develop a business case.

  14. On the origin of radiation growth of hcp crystals

    SciTech Connect (OSTI)

    Golubov, Stanislav I; Barashev, Aleksandr; Stoller, Roger E

    2012-03-01

    The aim of the present work is to study theoretically the radiation growth (RG) of hcp-type materials with a particular focus on the effect of one-dimensionally (1-D) migrating clusters of self-interstitial atoms (SIAs), which are steadily produced in displacement cascades under neutron or heavy-ion irradiation. A reaction-diffusion model is developed for the description of RG in single hcp-type metallic crystals. The model reproduces all RG stages observed in neutron-irradiated annealed samples of pure Zr and Zr alloys, such as high strain rate at low, strain saturation at intermediate and breakaway growth at relatively high irradiation doses. In addition, it accounts for the striking observations of negative strains in prismatic directions and coexistence of vacancy- and SIA-type prismatic loops. The role of cold work in RG behavior and alignment of the vacancy-type loops along basal planes are revealed and the maximum strain rate is estimated.

  15. Carbon nanotube forests growth using catalysts from atomic layer deposition

    SciTech Connect (OSTI)

    Chen, Bingan; Zhang, Can; Esconjauregui, Santiago; Xie, Rongsi; Zhong, Guofang; Robertson, John; Bhardwaj, Sunil; Cepek, Cinzia

    2014-04-14

    We have grown carbon nanotubes using Fe and Ni catalyst films deposited by atomic layer deposition. Both metals lead to catalytically active nanoparticles for growing vertically aligned nanotube forests or carbon fibres, depending on the growth conditions and whether the substrate is alumina or silica. The resulting nanotubes have narrow diameter and wall number distributions that are as narrow as those grown from sputtered catalysts. The state of the catalyst is studied by in-situ and ex-situ X-ray photoemission spectroscopy. We demonstrate multi-directional nanotube growth on a porous alumina foam coated with Fe prepared by atomic layer deposition. This deposition technique can be useful for nanotube applications in microelectronics, filter technology, and energy storage.

  16. ALS Technique Gives Novel View of Lithium Battery Dendrite Growth

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ALS Technique Gives Novel View of Lithium Battery Dendrite Growth Print Lithium-ion batteries, popular in today's electronic devices and electric vehicles, could gain significant energy density if their graphite anodes were replaced with lithium metal anodes. But there's a major concern with substituting lithium-when the battery cycles, microscopic fibers of the lithium anodes ("dendrites") form on the surface of the lithium electrode and spread across the electrolyte until they reach

  17. Material and method for promoting the growth of anaerobic bacteria

    DOE Patents [OSTI]

    Adler, Howard I. (128 Indian La., Oak Ridge, TN 37830)

    1984-01-01

    A material and method for promoting the growth of anaerobic bacteria which includes a nutrient media containing a hydrogen donor and sterile membrane fragments of bacteria having an electron transfer system which reduces oxygen to water. Dissolved oxygen in the medium is removed by adding the sterile membrane fragments to the nutrient medium and holding the medium at a temperature of about 10.degree. to about 60.degree. C. until the dissolved oxygen is removed.

  18. Material and method for promoting the growth of anaerobic bacteria

    DOE Patents [OSTI]

    Adler, H.I.

    1984-10-09

    A material and method is disclosed for promoting the growth of anaerobic bacteria which includes a nutrient media containing a hydrogen donor and sterile membrane fragments of bacteria having an electron transfer system which reduces oxygen to water. Dissolved oxygen in the medium is removed by adding the sterile membrane fragments to the nutrient medium and holding the medium at a temperature of about 10 to about 60 C until the dissolved oxygen is removed. No Drawings

  19. Analysis of kicker noise induced beam emittance growth

    SciTech Connect (OSTI)

    Zhang W.; Sandberg, J.; Ahrens, L.; Blacker, I.M.; Brennan, M.; Blaskiewicz, M.; Fischer, W.; Hahn, H.; Huang, H.; Kling, N.; Lafky, M.; Marr, G.; Mernick, K.; Mi, J.; Minty, M.; Naylor, C.; Roser, T.; Shrey, T.; van Kuik, B.; Zelenski, A.

    2012-05-20

    Over the last few years, physicists have occasionally observed the presence of noise acting on the RHIC beams leading to emittance growth at high beam energies. While the noise was sporadic in the past, it became persistent during the Run-11 setup period. An investigation diagnosed the source as originating from the RHIC dump kicker system. Once identified the issue was quickly resolved. We report in this paper the investigation result, circuit analysis, measured and simulated waveforms, solutions, and future plans.

  20. A 15 Year History of Growth and Development

    Office of Scientific and Technical Information (OSTI)

    DOE R&D Accomplishments A 15 Year History of Growth and Development Introduction The DOE R&D Accomplishments website was developed to improve the visibility of DOE accomplishments by broadening and integrating access to important advances made possible by past DOE/predecessor research and development. It showcases the proud heritage of the Department's research and development and highlights benefits that are being realized now. Selection of electronic documents and Web page content is