Sample records for groups accelerator systems

  1. AGS SUPER NEUTRINO BEAM FACILITY ACCELERATOR AND TARGET SYSTEM DESIGN (NEUTRINO WORKING GROUP REPORT-II).

    SciTech Connect (OSTI)

    DIWAN,M.; MARCIANO,W.; WENG,W.; RAPARIA,D.

    2003-04-21T23:59:59.000Z

    This document describes the design of the accelerator and target systems for the AGS Super Neutrino Beam Facility. Under the direction of the Associate Laboratory Director Tom Kirk, BNL has established a Neutrino Working Group to explore the scientific case and facility requirements for a very long baseline neutrino experiment. Results of a study of the physics merit and detector performance was published in BNL-69395 in October 2002, where it was shown that a wide-band neutrino beam generated by a 1 MW proton beam from the AGS, coupled with a half megaton water Cerenkov detector located deep underground in the former Homestake mine in South Dakota would be able to measure the complete set of neutrino oscillation parameters: (1) precise determination of the oscillation parameters {Delta}m{sub 32}{sup 2} and sin{sup 2} 2{theta}{sub 32}; (2) detection of the oscillation of {nu}{sub {mu}}-{nu}{sub e} and measurement of sin{sup 2} 2{theta}{sub 13}; (3) measurement of {Delta}m{sub 21}{sup 2} sin 2{theta}{sub 12} in a {nu}{sub {mu}} {yields} {nu}{sub e} appearance mode, independent of the value of {theta}{sub 13}; (4) verification of matter enhancement and the sign of {Delta}m{sub 32}{sup 2}; and (5) determination of the CP-violation parameter {delta}{sub CP} in the neutrino sector. This report details the performance requirements and conceptual design of the accelerator and the target systems for the production of a neutrino beam by a 1.0 MW proton beam from the AGS. The major components of this facility include a new 1.2 GeV superconducting linac, ramping the AGS at 2.5 Hz, and the new target station for 1.0 MW beam. It also calls for moderate increase, about 30%, of the AGS intensity per pulse. Special care is taken to account for all sources of proton beam loss plus shielding and collimation of stray beam halo particles to ensure equipment reliability and personal safety. A preliminary cost estimate and schedule for the accelerator upgrade and target system are also included.

  2. Energy Management Working Group: Accelerating Energy Management

    E-Print Network [OSTI]

    Scheihing, P.

    2014-01-01T23:59:59.000Z

    for Standardization (ISO) published the ISO 50001 energy management standard in 2011. ISO 50001 provides industrial companies with guidelines for integrating energy efficiency into their management practices— including fine-tuning production processes... efficiency. GSEP’s Energy Management Working Group (EMWG) advocates the increased adoption of EnMS or ISO 50001 in industry and commercial buildings. It goal is to accelerate the adoption and use of energy management systems in industrial facilities...

  3. RFQ accelerator tuning system

    DOE Patents [OSTI]

    Bolie, Victor W. (Albuquerque, NM)

    1990-01-01T23:59:59.000Z

    A cooling system is provided for maintaining a preselected operating temperature in a device, which may be an RFQ accelerator, having a variable heat removal requirement, by circulating a cooling fluid through a cooling system remote from the device. Internal sensors in the device enable an estimated error signal to be generated from parameters which are indicative of the heat removal requirement from the device. Sensors are provided at predetermined locations in the cooling system for outputting operational temperature signals. Analog and digital computers define a control signal functionally related to the temperature signals and the estimated error signal, where the control signal is defined effective to return the device to the preselected operating temperature in a stable manner. The cooling system includes a first heat sink responsive to a first portion of the control signal to remove heat from a major portion of the circulating fluid. A second heat sink is responsive to a second portion of the control signal to remove heat from a minor portion of the circulating fluid. The cooled major and minor portions of the circulating fluid are mixed in response to a mixing portion of the control signal, which is effective to proportion the major and minor portions of the circulating fluid to establish a mixed fluid temperature which is effective to define the preselected operating temperature for the remote device. In an RFQ environment the stable temperature control enables the resonant frequency of the device to be maintained at substantially a predetermined value during transient operations.

  4. RFQ accelerator tuning system

    DOE Patents [OSTI]

    Bolie, V.W.

    1990-07-03T23:59:59.000Z

    A cooling system is provided for maintaining a preselected operating temperature in a device, which may be an RFQ accelerator, having a variable heat removal requirement, by circulating a cooling fluid through a cooling system remote from the device. Internal sensors in the device enable an estimated error signal to be generated from parameters which are indicative of the heat removal requirement from the device. Sensors are provided at predetermined locations in the cooling system for outputting operational temperature signals. Analog and digital computers define a control signal functionally related to the temperature signals and the estimated error signal, where the control signal is defined effective to return the device to the preselected operating temperature in a stable manner. The cooling system includes a first heat sink responsive to a first portion of the control signal to remove heat from a major portion of the circulating fluid. A second heat sink is responsive to a second portion of the control signal to remove heat from a minor portion of the circulating fluid. The cooled major and minor portions of the circulating fluid are mixed in response to a mixing portion of the control signal, which is effective to proportion the major and minor portions of the circulating fluid to establish a mixed fluid temperature which is effective to define the preselected operating temperature for the remote device. In an RFQ environment the stable temperature control enables the resonant frequency of the device to be maintained at substantially a predetermined value during transient operations. 3 figs.

  5. Parametric Study of Emerging High Power Accelerator Applications Using Accelerator Systems Model (ASM)

    E-Print Network [OSTI]

    Berwald, D H; Myers, T J; Paulson, C C; Peacock, M A; Piaszczyk, C M; Rathke, J W; Piechowiak, E M

    1996-01-01T23:59:59.000Z

    Parametric Study of Emerging High Power Accelerator Applications Using Accelerator Systems Model (ASM)

  6. Energy Management Working Group: Accelerating Energy Management 

    E-Print Network [OSTI]

    Scheihing, P.

    2014-01-01T23:59:59.000Z

    Countries participating in the Global Superior Energy Performance (GSEP) Energy Management Working Group (EMWG) are leveraging their resources and taking collective action to strengthen national and international efforts to facilitate the adoption...

  7. Summary Report of Working Group 1: Laser-Plasma Acceleration

    E-Print Network [OSTI]

    Geddes, Cameron Guy Robinson

    structure providing a linear mechanism with potential to harness low-energy laser systems [11 orders beyond conventional machines, with quasi-monoenergetic beams at MeV-GeV energies, making them and diagnostics. This includes laser wakefield acceleration [1], where acceleration by a plasma wave excited

  8. Modified Accelerated Cost-Recovery System (MACRS)

    Broader source: Energy.gov [DOE]

    Under the federal Modified Accelerated Cost-Recovery System (MACRS), businesses may recover investments in certain property through depreciation deductions. The MACRS establishes a set of class l...

  9. Solar system constraints on Rindler acceleration

    E-Print Network [OSTI]

    Sante Carloni; Daniel Grumiller; Florian Preis

    2011-05-09T23:59:59.000Z

    We discuss the classical tests of general relativity in the presence of Rindler acceleration. Among these tests the perihelion shifts give the tightest constraints and indicate that the Pioneer anomaly cannot be caused by a universal solar system Rindler acceleration. We address potential caveats for massive test-objects. Our tightest bound on Rindler acceleration that comes with no caveats is derived from radar echo delay and yields |a|<3nm/s^2.

  10. Power Systems Group Home Page

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    General Information ASD Groups ESHQA Operations Argonne Home > Advanced Photon Source > Power Systems Group This page is currently under construction. Old PS Group Site (visible...

  11. A new tool for accelerator system modeling and analysis

    SciTech Connect (OSTI)

    Gillespie, G.H.; Hill, B.W. [G.H. Gillespie Associates, Inc., Del Mar, CA (United States); Jameson, R.A. [Los Alamos National Lab., NM (United States)

    1994-09-01T23:59:59.000Z

    A novel computer code is being developed to generate system level designs of radiofrequency ion accelerators. The goal of the Accelerator System Model (ASM) code is to create a modeling and analysis tool that is easy to use, automates many of the initial design calculations, supports trade studies used in assessing alternate designs and yet is flexible enough to incorporate new technology concepts as they emerge. Hardware engineering parameters and beam dynamics are modeled at comparable levels of fidelity. Existing scaling models of accelerator subsystems were sued to produce a prototype of ASM (version 1.0) working within the Shell for Particle Accelerator Related Codes (SPARC) graphical user interface. A small user group has been testing and evaluating the prototype for about a year. Several enhancements and improvements are now being developed. The current version (1.1) of ASM is briefly described and an example of the modeling and analysis capabilities is illustrated.

  12. Accelerating the transformation of power systems

    E-Print Network [OSTI]

    Accelerating the transformation of power systems Introduction Flexibility of operation--the ability of a power system to respond to change in demand and supply--is a characteristic of all power systems. Flexibility is especially prized in twenty-first century power systems, with higher levels of grid

  13. REPORT OF THE WORKING GROUP ON OTHER ACCELERATION SCHEMES

    E-Print Network [OSTI]

    Sessler, A.M.

    2008-01-01T23:59:59.000Z

    Resonance Accelerator (PB) 5. Plasma Focus (L) 6. Two-Beambe most important for the Plasma Focus Accelerator. RADIALAccelerator (Csonka) Plasma Focus (Hora) Radial Implosion

  14. Vehicle Systems Integration Laboratory Accelerates Powertrain Development

    SciTech Connect (OSTI)

    None

    2014-04-15T23:59:59.000Z

    ORNL's Vehicle Systems Integration (VSI) Laboratory accelerates the pace of powertrain development by performing prototype research and characterization of advanced systems and hardware components. The VSI Lab is capable of accommodating a range of platforms from advanced light-duty vehicles to hybridized Class 8 powertrains with the goals of improving overall system efficiency and reducing emissions.

  15. Vehicle Systems Integration Laboratory Accelerates Powertrain Development

    ScienceCinema (OSTI)

    None

    2014-06-25T23:59:59.000Z

    ORNL's Vehicle Systems Integration (VSI) Laboratory accelerates the pace of powertrain development by performing prototype research and characterization of advanced systems and hardware components. The VSI Lab is capable of accommodating a range of platforms from advanced light-duty vehicles to hybridized Class 8 powertrains with the goals of improving overall system efficiency and reducing emissions.

  16. Accelerating the transformation of power systems

    E-Print Network [OSTI]

    Accelerating the transformation of power systems Ancillary Services Peer Exchange with India in power system transformation is an increasingly vital resource for national and subnational decision of power systems. The Power Partnership is a multilateral effort of the Clean Energy Ministerial and serves

  17. Application accelerator system having bunch control

    DOE Patents [OSTI]

    Wang, Dunxiong (Newport News, VA); Krafft, Geoffrey Arthur (Newport News, VA)

    1999-01-01T23:59:59.000Z

    An application accelerator system for monitoring the gain of a free electron laser. Coherent Synchrotron Radiation (CSR) detection techniques are used with a bunch length monitor for ultra short, picosec to several tens of femtosec, electron bunches. The monitor employs an application accelerator, a coherent radiation production device, an optical or beam chopping device, an infrared radiation collection device, a narrow-banding filter, an infrared detection device, and a control.

  18. Application accelerator system having bunch control

    DOE Patents [OSTI]

    Wang, D.; Krafft, G.A.

    1999-06-22T23:59:59.000Z

    An application accelerator system for monitoring the gain of a free electron laser is disclosed. Coherent Synchrotron Radiation (CSR) detection techniques are used with a bunch length monitor for ultra short, picosec to several tens of femtosec, electron bunches. The monitor employs an application accelerator, a coherent radiation production device, an optical or beam chopping device, an infrared radiation collection device, a narrow-banding filter, an infrared detection device, and a control. 1 fig.

  19. Fermilab accelerator control system: Analog monitoring facilities

    SciTech Connect (OSTI)

    Seino, K.; Anderson, L.; Smedinghoff, J.

    1987-10-01T23:59:59.000Z

    Thousands of analog signals are monitored in different areas of the Fermilab accelerator complex. For general purposes, analog signals are sent over coaxial or twinaxial cables with varying lengths, collected at fan-in boxes and digitized with 12 bit multiplexed ADCs. For higher resolution requirements, analog signals are digitized at sources and are serially sent to the control system. This paper surveys ADC subsystems that are used with the accelerator control systems and discusses practical problems and solutions, and it describes how analog data are presented on the console system.

  20. Generic device controller for accelerator control systems

    SciTech Connect (OSTI)

    Mariotti, R.; Buxton, W.; Frankel, R.; Hoff, L.

    1987-01-01T23:59:59.000Z

    A new distributed intelligence control system has become operational at the AGS for transport, injection, and acceleration of heavy ions. A brief description of the functionality of the physical devices making up the system is given. An attempt has been made to integrate the devices for accelerator specific interfacing into a standard microprocessor system, namely, the Universal Device Controller (UDC). The main goals for such a generic device controller are to provide: local computing power; flexibility to configure; and real time event handling. The UDC assemblies and software are described. (LEW)

  1. BNL ACCELERATOR TEST FACILITY CONTROL SYSTEM UPGRADE R. Malone...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ACCELERATOR TEST FACILITY CONTROL SYSTEM UPGRADE R. Malone, I. Ben-Zvi, X. Wang, V. Yakimenko BNL , Upton, NY 11973, USA Abstract Brookhaven National Laboratory's Accelerator...

  2. The BNL Accelerator Test Facility control system

    SciTech Connect (OSTI)

    Malone, R.; Bottke, I.; Fernow, R.; Ben-Zvi, I.

    1993-01-01T23:59:59.000Z

    Described is the VAX/CAMAC-based control system for Brookhaven National Laboratory's Accelerator Test Facility, a laser/linac research complex. Details of hardware and software configurations are presented along with experiences of using Vsystem, a commercial control system package.

  3. Ground test accelerator control system software

    SciTech Connect (OSTI)

    Burczyk, L.; Dalesio, R.; Dingler, R.; Hill, J.; Howell, J.A.; Kerstiens, D.; King, R.; Kozubal, A.; Little, C.; Martz, V.; Rothrock, R.; Sutton, J.

    1988-01-01T23:59:59.000Z

    The GTA control system provides an environment in which the automation of a state-of-the-art accelerator can be developed. It makes use of commercially available computers, workstations, computer networks, industrial I/O equipment, and software. This system has built-in supervisory control (like most accelerator control systems), tools to support continuous control (like the process control industry), and sequential control for automatic startup and fault recovery (like few other accelerator control systems). Several software tools support these levels of control: a real-time operating system (VxWorks) with a real-time kernel (VRTX), a configuration database, a sequencer, and a graphics editor. VxWorks supports multitasking, fast context-switching, and preemptive scheduling. VxWorks/VRTX is a network-based development environment specifically designed to work in partnership with the UNIX operating system. A database provides the interface to the accelerator components. It consists of a run time library and a database configuration and editing tool. A sequencer initiates and controls the operation of all sequence programs (expressed as state programs). A graphics editor gives the user the ability to create color graphic displays showing the state of the machine in either text or graphics form. 11 refs., 2 figs.

  4. Summary Report of Working Group 6: Laser-Plasma Acceleration

    E-Print Network [OSTI]

    Leemans, Wim P.; Downer, Michael; Siders, Craig

    2008-01-01T23:59:59.000Z

    be an important focus of laser-plasma acceleration researchfocus. In both cases, light regions of the image ionized and heated the plasma,

  5. ASD Groups | Advanced Photon Source

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ASD Groups Accelerator Operations and Physics Applies integrated expertise in accelerator physics, operations techniques, safety systems, software development, and numerical...

  6. Induction accelerators for the phase rotator system

    SciTech Connect (OSTI)

    Reginato, Lou; Yu, Simon; Vanecek, Dave

    2001-07-30T23:59:59.000Z

    The principle of magnetic induction has been applied to the acceleration of high current beams in betatrons and a variety of induction accelerators. The linear induction accelerator (LIA) consists of a simple nonresonant structure where the drive voltage is applied to an axially symmetric gap that encloses a toroidal ferromagnetic material. The change in flux in the magnetic core induces an axial electric field that provides particle acceleration. This simple nonresonant (low Q) structure acts as a single turn transformer that can accelerate from hundreds of amperes to tens of kiloamperes, basically only limited by the drive impedance. The LIA is typically a low gradient structure that can provide acceleration fields of varying shapes and time durations from tens of nanoseconds to several microseconds. The efficiency of the LIA depends on the beam current and can exceed 50% if the beam current exceeds the magnetization current required by the ferromagnetic material. The acceleration voltage available is simply given by the expression V=A dB/dt. Hence, for a given cross section of material, the beam pulse duration influences the energy gain. Furthermore, a premium is put on minimizing the diameter, which impacts the total weight or cost of the magnetic material. The diameter doubly impacts the cost of the LIA since the power (cost) to drive the cores is proportional to the volume as well. The waveform requirements during the beam pulse makes it necessary to make provisions in the pulsing system to maintain the desired dB/dt during the useful part of the acceleration cycle. This is typically done two ways, by using the final stage of the pulse forming network (PFN) and by the pulse compensation network usually in close proximity of the acceleration cell. The choice of magnetic materials will be made by testing various materials both ferromagnetic and ferrimagnetic. These materials will include the nickel-iron, silicon steel amorphous and various types of ferrites not only to determine the properties that are essential in this application but the energy losses in the magnetization process which directly impact the cost.

  7. Application of local area networks to accelerator control systems at the Stanford Linear Accelerator

    SciTech Connect (OSTI)

    Fox, J.D.; Linstadt, E.; Melen, R.

    1983-03-01T23:59:59.000Z

    The history and current status of SLAC's SDLC networks for distributed accelerator control systems are discussed. These local area networks have been used for instrumentation and control of the linear accelerator. Network topologies, protocols, physical links, and logical interconnections are discussed for specific applications in distributed data acquisition and control system, computer networks and accelerator operations.

  8. Application of local area networks to accelerator control systems at the Stanford linear accelerator

    SciTech Connect (OSTI)

    Fox, J.D.; Linstadt, E.; Melen, R.

    1983-08-01T23:59:59.000Z

    The history and current status of SLAC's SDLC networks for distributed accelerator control systems are discussed. These local area networks have been used for instrumentation and control of the linear accelerator. Network topologies, protocols, physical links, and logical interconnections are discussed for specific applications in distributed data acquisition and control systems, computer networks and accelerator operations.

  9. Hardware Accelerator for MIMO Wireless Systems

    E-Print Network [OSTI]

    Bhagawat, Pankaj

    2012-02-14T23:59:59.000Z

    of DOCTOR OF PHILOSOPHY Approved by: Chair of Committee, Gwan Choi Committee Members, Jiang Hu Rabi Mahapatra Jim Ji Head of Department, Costas Georghiades December 2011 Major Subject: Computer Engineering iii ABSTRACT Hardware Accelerator for MIMO... Wireless Systems. (December 2011) Pankaj Bhagawat, B.S., National Insitute of Technology, Tiruchirapally, India; M.S., Texas A&M University Chair of Advisory Committee: Dr. Gwan Choi Ever increasing demand for higher data rates and better Quality...

  10. Intraoperative radiation therapy using mobile electron linear accelerators: Report of AAPM Radiation Therapy Committee Task Group No. 72

    SciTech Connect (OSTI)

    Sam Beddar, A.; Biggs, Peter J.; Chang Sha; Ezzell, Gary A.; Faddegon, Bruce A.; Hensley, Frank W.; Mills, Michael D. [Department of Radiation Physics, Division of Radiation Oncology, Unit 94, University of Texas M.D. Anderson Cancer Center, Houston, Texas 77030 (United States); Department of Radiation Oncology, Massachusetts General Hospital, Boston, Massachusetts 02114 (United States); Department of Radiation Oncology, University of North Carolina School of Medicine, Chapel Hill, North Carolina 27599 (United States); Department of Radiation Oncology, Mayo Clinic Scottsdale, Scottsdale, Arizona 85259 (United States); Department of Radiation Oncology, University of California San Francisco, San Francisco, California 94143 (United States); Department of Radiation Oncology, University of Heidelberg, 69120 Heidelberg (Germany); Department of Radiation Oncology, James Graham Brown Cancer Center, Louisville, Kentucky 40202 (United States)

    2006-05-15T23:59:59.000Z

    Intraoperative radiation therapy (IORT) has been customarily performed either in a shielded operating suite located in the operating room (OR) or in a shielded treatment room located within the Department of Radiation Oncology. In both cases, this cancer treatment modality uses stationary linear accelerators. With the development of new technology, mobile linear accelerators have recently become available for IORT. Mobility offers flexibility in treatment location and is leading to a renewed interest in IORT. These mobile accelerator units, which can be transported any day of use to almost any location within a hospital setting, are assembled in a nondedicated environment and used to deliver IORT. Numerous aspects of the design of these new units differ from that of conventional linear accelerators. The scope of this Task Group (TG-72) will focus on items that particularly apply to mobile IORT electron systems. More specifically, the charges to this Task Group are to (i) identify the key differences between stationary and mobile electron linear accelerators used for IORT (ii) describe and recommend the implementation of an IORT program within the OR environment, (iii) present and discuss radiation protection issues and consequences of working within a nondedicated radiotherapy environment, (iv) describe and recommend the acceptance and machine commissioning of items that are specific to mobile electron linear accelerators, and (v) design and recommend an efficient quality assurance program for mobile systems.

  11. accelerator code group: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Duadic Group Algebra Codes Quantum Physics (arXiv) Summary: Duadic group algebra codes are a generalization of...

  12. Novel Approach to Linear Accelerator Superconducting Magnet System

    SciTech Connect (OSTI)

    Kashikhin, Vladimir; /Fermilab

    2011-11-28T23:59:59.000Z

    Superconducting Linear Accelerators include a superconducting magnet system for particle beam transportation that provides the beam focusing and steering. This system consists of a large number of quadrupole magnets and dipole correctors mounted inside or between cryomodules with SCRF cavities. Each magnet has current leads and powered from its own power supply. The paper proposes a novel approach to magnet powering based on using superconducting persistent current switches. A group of magnets is powered from the same power supply through the common, for the group of cryomodules, electrical bus and pair of current leads. Superconducting switches direct the current to the chosen magnet and close the circuit providing the magnet operation in a persistent current mode. Two persistent current switches were fabricated and tested. In the paper also presented the results of magnetic field simulations, decay time constants analysis, and a way of improving quadrupole magnetic center stability. Such approach substantially reduces the magnet system cost and increases the reliability.

  13. Systems and methods for the magnetic insulation of accelerator electrodes in electrostatic accelerators

    DOE Patents [OSTI]

    Grisham, Larry R

    2013-12-17T23:59:59.000Z

    The present invention provides systems and methods for the magnetic insulation of accelerator electrodes in electrostatic accelerators. Advantageously, the systems and methods of the present invention improve the practically obtainable performance of these electrostatic accelerators by addressing, among other things, voltage holding problems and conditioning issues. The problems and issues are addressed by flowing electric currents along these accelerator electrodes to produce magnetic fields that envelope the accelerator electrodes and their support structures, so as to prevent very low energy electrons from leaving the surfaces of the accelerator electrodes and subsequently picking up energy from the surrounding electric field. In various applications, this magnetic insulation must only produce modest gains in voltage holding capability to represent a significant achievement.

  14. Energy Systems Group Annual Report

    E-Print Network [OSTI]

    Anand, N. K.; Caton, J.; Heffington, W. M.; O'Neal, D. L.; Somasundaram, S.; Turner, W. D.

    1986-01-01T23:59:59.000Z

    in this project. Annual expenditures for energy use in Texas State Agencies in 1984 was over two hundred million dollars. This study has four major tasks. First, the Energy Systems Laboratory is the data collection center for monthly energy data from each... by the Energy Systems Group is improving the efficiency of energy use. Currently, the research focuses on improving energy efficiency in heating and air conditioning equipment, improving thermal efficiency of buildings, implementation of Cogeneration systems...

  15. NERSC seeks Computational Systems Group Lead

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    seeks Computational Systems Group Lead NERSC seeks Computational Systems Group Lead January 6, 2011 by Katie Antypas Note: This position is now closed. The Computational Systems...

  16. accelerator driven systems: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    purpose of incinerating long-lived radionuclides in high- level waste 5 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  17. accelerator driven system: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    purpose of incinerating long-lived radionuclides in high- level waste 5 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  18. Systems Biology Group Decision Making

    E-Print Network [OSTI]

    entities (e.g., molecular, cellular, organism, ecological) #12;OHIO STATE T . H . E UNIVERSITY Systems/analysis of perception, attention, choice, learning, optimality,... #12;OHIO STATE T . H . E UNIVERSITY Group decision making, evolution and ecology Current work: Modeling/analysis of coordinated motion, foraging, choice

  19. Small system for tritium accelerator mass spectrometry

    DOE Patents [OSTI]

    Roberts, M.L.; Davis, J.C.

    1993-02-23T23:59:59.000Z

    Apparatus for ionizing and accelerating a sample containing isotopes of hydrogen and detecting the ratios of hydrogen isotopes contained in the sample is disclosed. An ion source generates a substantially linear ion beam including ions of tritium from the sample. A radio-frequency quadrupole accelerator is directly coupled to and axially aligned with the source at an angle of substantially zero degrees. The accelerator accelerates species of the sample having different mass to different energy levels along the same axis as the ion beam. A spectrometer is used to detect the concentration of tritium ions in the sample. In one form of the invention, an energy loss spectrometer is used which includes a foil to block the passage of hydrogen, deuterium and [sup 3]He ions, and a surface barrier or scintillation detector to detect the concentration of tritium ions. In another form of the invention, a combined momentum/energy loss spectrometer is used which includes a magnet to separate the ion beams, with Faraday cups to measure the hydrogen and deuterium and a surface barrier or scintillation detector for the tritium ions.

  20. Small system for tritium accelerator mass spectrometry

    DOE Patents [OSTI]

    Roberts, Mark L. (Livermore, CA); Davis, Jay C. (Livermore, CA)

    1993-01-01T23:59:59.000Z

    Apparatus for ionizing and accelerating a sample containing isotopes of hydrogen and detecting the ratios of hydrogen isotopes contained in the sample is disclosed. An ion source generates a substantially linear ion beam including ions of tritium from the sample. A radio-frequency quadrupole accelerator is directly coupled to and axially aligned with the source at an angle of substantially zero degrees. The accelerator accelerates species of the sample having different mass to different energy levels along the same axis as the ion beam. A spectrometer is used to detect the concentration of tritium ions in the sample. In one form of the invention, an energy loss spectrometer is used which includes a foil to block the passage of hydrogen, deuterium and .sup.3 He ions, and a surface barrier or scintillation detector to detect the concentration of tritium ions. In another form of the invention, a combined momentum/energy loss spectrometer is used which includes a magnet to separate the ion beams, with Faraday cups to measure the hydrogen and deuterium and a surface barrier or scintillation detector for the tritium ions.

  1. accelerator elektroniczny system: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Preprints Summary: The vacuum control system of most of the CERN accelerators is based on Siemens PLCs and on PVSS SCADA. After the transition from the LHC commissioning phase to...

  2. Distributed Energy Systems Integration Group (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-10-01T23:59:59.000Z

    Factsheet developed to describe the activites of the Distributed Energy Systems Integration Group within NREL's Electricity, Resources, and Buildings Systems Integration center.

  3. Hardware Accelerator for MIMO Wireless Systems 

    E-Print Network [OSTI]

    Bhagawat, Pankaj

    2012-02-14T23:59:59.000Z

    potential that multiple antenna systems promise. Furthermore, in order to make judicious use of the available bandwidth, the baseband units have to dynamically adapt to different modes (modulation schemes, code rates etc) of operations. Flexibility and high...

  4. Quick setup of unit test for accelerator controls system

    SciTech Connect (OSTI)

    Fu, W.; D'Ottavio, T.; Gassner, D.; Nemesure, S.; Morris, J.

    2011-03-28T23:59:59.000Z

    Testing a single hardware unit of an accelerator control system often requires the setup of a program with graphical user interface. Developing a dedicated application for a specific hardware unit test could be time consuming and the application may become obsolete after the unit tests. This paper documents a methodology for quick design and setup of an interface focused on performing unit tests of accelerator equipment with minimum programming work. The method has three components. The first is a generic accelerator device object (ADO) manager which can be used to setup, store, and log testing controls parameters for any unit testing system. The second involves the design of a TAPE (Tool for Automated Procedure Execution) sequence file that specifies and implements all te testing and control logic. The sting third is the design of a PET (parameter editing tool) page that provides the unit tester with all the necessary control parameters required for testing. This approach has been used for testing the horizontal plane of the Stochastic Cooling Motion Control System at RHIC.

  5. Cryogenic system for the MYRRHA superconducting linear accelerator

    SciTech Connect (OSTI)

    Chevalier, Nicolas R.; Junquera, Tomas [Accelerators and Cryogenic Systems, 86, rue de Paris, 91400 Orsay (France); Thermeau, Jean-Pierre [Institut de Physique Nucléaire, Université Paris Sud, 91400 Orsay (France); Romão, Luis Medeiros; Vandeplassche, Dirk [SCK-CEN, Boeretang 200, 2400 Mol (Belgium)

    2014-01-29T23:59:59.000Z

    SCK?CEN, the Belgian Nuclear Research Centre, is designing MYRRHA, a flexible fast spectrum research reactor (80 MW{sub th}), conceived as an accelerator driven system (ADS), able to operate in sub-critical and critical modes. It contains a continuous-wave (CW) superconducting (SC) proton accelerator of 600 MeV, a spallation target and a multiplying core with MOX fuel, cooled by liquid lead-bismuth (Pb-Bi). From 17 MeV onward, the SC accelerator will consist of 48 ?=0.36 spoke-loaded cavities (352 MHz), 34 ?=0.47 elliptical cavities (704 MHz) and 60 ?=0.65 elliptical cavities (704 MHz). We present an analysis of the thermal loads and of the optimal operating temperature of the cryogenic system. In particular, the low operating frequency of spoke cavities makes their operation in CW mode possible both at 4.2 K or at 2 K. Our analysis outlines the main factors that determine at what temperature the spoke cavities should be operated. We then present different cryogenic fluid distribution schemes, important characteristics (storage, transfer line, etc.) and the main challenges offered by MYRRHA in terms of cryogenics.

  6. Feed forward rf control system of the accelerator test facility

    SciTech Connect (OSTI)

    Ben-Zvi, I.; Xie, Jialin; Zhang, Renshan.

    1991-01-01T23:59:59.000Z

    We report a scheme to control the amplitude and phase of the rf accelerating field in a klystron driven electron linac. The amplitude and phase distribution within the rf pulse can be controlled to follow specified functions to reduce the energy spread of the electron beam being accelerated. The scheme employs fast beam energy and phase detectors and voltage-controlled electronic attenuator and phase shifter in the amplifier chain. The control voltages of these devices are generated by arbitrary function generators. The function generators' outputs are calculated numerically using an algorithm which takes into consideration the desired target function and the deviation (due to load variations or system parameter drift) from the target function. Results of preliminary tests on producing flat rf power and phase pulses from a high power klystron indicate that amplitude variation of {plus minus}0.2% and phase variation of {plus minus}1{degree} can be readily achieved. 4 refs., 3 figs.

  7. Group M1 Response to the Snowmass 2001 Charge Working Group M1: Muon-Based Accelerators

    E-Print Network [OSTI]

    ; cost-effective longitudinal manipulation and ionization cooling techniques for reducing transverse emittance; and rapid and efficient acceleration techniques that accommodate large longitudinal, but requirements are more severe. Emittance reduction must include longitudinal cooling ("emittance exchange

  8. Energy Systems Group ESCO Qualification Sheet | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Systems Group ESCO Qualification Sheet Energy Systems Group ESCO Qualification Sheet Document outlines the energy service company (ESCO) qualifications for Energy Systems...

  9. ENABLING SYSTEMS THINKING TO ACCELERATE THE DEVELOPMENT OF SENIOR SYSTEMS ENGINEERS

    E-Print Network [OSTI]

    de Weck, Olivier L.

    ENABLING SYSTEMS THINKING TO ACCELERATE THE DEVELOPMENT OF SENIOR SYSTEMS ENGINEERS by Heidi Leoti of Cincinnati SUBMITTED TO THE ENGINEERING SYSTEMS DIVISION IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE DEGREE OF DOCTOR OF PHILOSOPHY IN ENGINEERING SYSTEMS AT THE MASSACHUSETTS INSTITUTE OF TECHNOLOGY

  10. Hydrgoen Storage Systems Analysis Working Group Meeting Summary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hydrgoen Storage Systems Analysis Working Group Meeting Summary Report Hydrgoen Storage Systems Analysis Working Group Meeting Summary Report Summary report from the May 17, 2007...

  11. RELWAY: a process data highway system optimized for accelerators

    SciTech Connect (OSTI)

    Frankel, R.; Buxton, W,; Kohler, K.; Warkentien, R.; White, A.

    1981-01-01T23:59:59.000Z

    The command/control scheme for the Isabelle accelerator, specifically the process data highway are discussed. (GHT)J

  12. accelerator-driven systems programme: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    purpose of incinerating long-lived radionuclides in high- level waste 4 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  13. accelerator-driven sub-critical system: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    purpose of incinerating long-lived radionuclides in high- level waste 4 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  14. accelerator-driven system ads: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    experimental facilities 1 T. Takizuka; T. Sasa; K. Tsujimoto; H. Takano 5 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  15. accelerator-driven systems fast: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    purpose of incinerating long-lived radionuclides in high- level waste 4 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  16. accelerator-driven system prototype: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    purpose of incinerating long-lived radionuclides in high- level waste 4 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  17. Modified Accelerated Cost-Recovery System (MACRS) + Bonus Depreciation (2008-2012)

    Broader source: Energy.gov [DOE]

    Under the federal Modified Accelerated Cost-Recovery System (MACRS), businesses may recover investments in certain property through depreciation deductions. The MACRS establishes a set of class...

  18. RFQ (radio-frequency quadrupole) accelerator tuning system

    DOE Patents [OSTI]

    Bolie, V.W.

    1988-04-12T23:59:59.000Z

    A cooling system is provided for maintaining a preselected operating temperature in a device, which may be an RFQ accelerator, having a variable heat removal requirement, by circulating a cooling fluid through a cooling system remote from the device. Internal sensors in the device enable an estimated error signal to be generated from parameters which are indicative of the heat removal requirement from the device. Sensors are provided at predetermined locations in the cooling system for outputting operational temperature signals. Analog and digital computers define a control signal functionally related to the temperature signals and the estimated error signal, where the control signal is defined effective to return the device to the preselected operating temperature in a stable manner. The cooling system includes a first heat sink responsive to a first portion of the control signal to remove heat from a major portion of the circulating fluid. A second heat sink is responsive to a second portion of the control to remove heat from a minor portion of the circulating fluid. The cooled major and minor portions of the circulating fluid are mixed in responsive to a mixing portion of the control signal, which is effective to proportion the major and minor portions of the circulating fluid to establish a mixed fluid temperature which is effective to define the preselected operating temperature for the remote device. 3 figs., 2 tabs.

  19. Mechanical Engineering & Design Group (AES-MED)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Techniques Sectors Directory Status and Schedule Safety and Training Divisions APS Engineering Support Division AES Groups Accelerator Systems Division ASD Groups X-ray Science...

  20. A Framework for a General Purpose Intelligent Control System for Particle Accelerators. Phase II Final Report

    SciTech Connect (OSTI)

    Dr. Robert Westervelt; Dr. William Klein; Dr. Michael Kroupa; Eric Olsson; Rick Rothrock

    1999-06-28T23:59:59.000Z

    Vista Control Systems, Inc. has developed a portable system for intelligent accelerator control. The design is general in scope and is thus configurable to a wide range of accelerator facilities and control problems. The control system employs a multi-layer organization in which knowledge-based decision making is used to dynamically configure lower level optimization and control algorithms.

  1. THE POWER SUPPLY SYSTEM FOR THE ACCELERATING COLUMN OF THE 2 MEV ELECTRON COOLER FOR COSY

    E-Print Network [OSTI]

    Kozak, Victor R.

    a high-energy electron beam. The power supply for the accelerating column of the electron cooling systemTHE POWER SUPPLY SYSTEM FOR THE ACCELERATING COLUMN OF THE 2 MEV ELECTRON COOLER FOR COSY D controlled voltage source for 60 kV, 1mA and an additional supply for the solenoids of the magnetic system

  2. Systems and methods for cylindrical hall thrusters with independently controllable ionization and acceleration stages

    DOE Patents [OSTI]

    Diamant, Kevin David; Raitses, Yevgeny; Fisch, Nathaniel Joseph

    2014-05-13T23:59:59.000Z

    Systems and methods may be provided for cylindrical Hall thrusters with independently controllable ionization and acceleration stages. The systems and methods may include a cylindrical channel having a center axial direction, a gas inlet for directing ionizable gas to an ionization section of the cylindrical channel, an ionization device that ionizes at least a portion of the ionizable gas within the ionization section to generate ionized gas, and an acceleration device distinct from the ionization device. The acceleration device may provide an axial electric field for an acceleration section of the cylindrical channel to accelerate the ionized gas through the acceleration section, where the axial electric field has an axial direction in relation to the center axial direction. The ionization section and the acceleration section of the cylindrical channel may be substantially non-overlapping.

  3. IBM System Storage Product Guide IBM Systems and Technology Group

    E-Print Network [OSTI]

    IBM System Storage Product Guide IBM Systems and Technology Group #12;2 Today, information has, reduce storage and archiving costs and enable continuous access to information in support of business requirements. Learn more about IBM Information Infrastructure, including the full range of data storage

  4. Transmutation of nuclear waste in accelerator-driven systems

    E-Print Network [OSTI]

    Herrera-Martínez, A

    2004-01-01T23:59:59.000Z

    Today more than ever energy is not only a cornerstone of human development, but also a key to the environmental sustainability of economic activity. In this context, the role of nuclear power may be emphasized in the years to come. Nevertheless, the problems of nuclear waste, safety and proliferation still remain to be solved. It is believed that the use of accelerator-driven systems (ADSs) for nuclear waste transmutation and energy production would address these problems in a simple, clean and economically viable, and therefore sustainable, manner. This thesis covers the major nuclear physics aspects of ADSs, in particular the spallation process and the core neutronics specific to this type of systems. The need for accurate nuclear data is described, together with a detailed analysis of the specific isotopes and energy ranges in which this data needs to be improved and the impact of their uncertainty. Preliminary experimental results for some of these isotopes, produced by the Neutron Time-of-Flight (n_TOF) ...

  5. Moltech Power Systems Group MPS Group | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual SiteofEvaluatingGroup |JilinLu anMicrogreen PolymersModular Energy DevicesMola(EC-LEDS)

  6. Controllability of Linear Systems with inner derivation on Lie Groups

    E-Print Network [OSTI]

    Boyer, Edmond

    Controllability of Linear Systems with inner derivation on Lie Groups Philippe JOUAN November 2 group of automorphisms. A control-ane system is linear if the drift is linear and the controlled vector groups are stated. The paper ends by many examples. Keywords: Lie groups; Linear systems; controllability

  7. Hydrogen Storage Systems Anlaysis Working Group Meeting, December...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Anlaysis Working Group Meeting, December 12, 2006 Hydrogen Storage Systems Anlaysis Working Group Meeting, December 12, 2006 This document provides a summary of the Hydrogen...

  8. Feasibility Study of Accelerator Driven System Proposed by JAEA

    SciTech Connect (OSTI)

    Sugawara, Takanori; Nishihara, Kenji; Tsujimoto, Kazufumi; Iwanaga, Kohei; Kurata, Yuji; Sasa, Toshinobu; Oigawa, Hiroyuki [Japan Atomic Energy Agency: 2-4 Shirakata-shirane Tokai-Mura, Ibaraki, 319-1195 (Japan)

    2007-07-01T23:59:59.000Z

    Accelerator Driven System (ADS) has been studied to transmute minor actinides (MA) discharged from spent fuel of commercial nuclear power plants. In Japan Atomic Energy Agency (JAEA), various R and D for an 800 MWt, lead bismuth eutectic (LBE) cooled ADS have been performed. The feasibility for the ADS is discussed in the present study in terms of the neutronics design, the safety analysis and the design of the beam window. In the neutronics design, the maximum temperature at the surface of the fuel pin was decreased from 578 deg. C to 498 deg. C by the adjustment of the ZrN inert matrix ratio for four zones. In the safety analysis, it was confirmed that there was very little possibility of core disruptive accidents at unprotected accidents in the ADS proposed by JAEA. For the design of the beam window, the parametric survey for the buckling failure was performed to discuss the methods to increase the margin for the buckling pressure. (authors)

  9. Disposition of Nuclear Waste Using Subcritical Accelerator-Driven Systems

    SciTech Connect (OSTI)

    Doolen, G.D.; Venneri, F.; Li, N.; Williamson, M.A.; Houts, M.; Lawrence, G.

    1998-06-27T23:59:59.000Z

    ATW destroys virtually all the plutonium and higher actinides without reprocessing the spent fuel in a way that could lead to weapons material diversion. An ATW facility consists of three major elements: (1) a high-power proton linear accelerator; (2) a pyrochemical spent fuel treatment i waste cleanup system; (3) a liquid lead-bismuth cooled burner that produces and utilizes an intense source-driven neutron flux for transmutation in a heterogeneous (solid fuel) core. The concept is the result of many years of development at LANL as well as other major international research centers. Once demonstrated and developed, ATW could be an essential part of a global non-proliferation strategy for countries that could build up large quantities of plutonium from their commercial reactor waste. ATW technology, initially proposed in the US, has received wide and rapidly increasing attention abroad, especially in Europe and the Far East with major programs now being planned, organized and tided. Substantial convergence presently exists on the technology choices among the programs, opening the possibility of a strong and effective international collaboration on the phased development of the ATW technology.

  10. Vacuum Systems Consensus Guideline for Department of Energy Accelerator Laboratories

    SciTech Connect (OSTI)

    Casey,R.; Haas, E.; Hseuh, H-C.; Kane, S.; Lessard, E.; Sharma, S.; Collins, J.; Toter, W. F.; Olis, D. R.; Pushka, D. R.; Ladd, P.; Jobe, R. K.

    2008-09-09T23:59:59.000Z

    Vacuum vessels, including evacuated chambers and insulated jacketed dewars, can pose a potential hazard to equipment and personnel from collapse, rupture due to back-fill pressurization, or implosion due to vacuum window failure. It is therefore important to design and operate vacuum systems in accordance with applicable and sound engineering principles. 10 CFR 851 defines requirements for pressure systems that also apply to vacuum vessels subject to back-fill pressurization. Such vacuum vessels are potentially subject to the requirements of the American Society of Mechanical Engineers (ASME) Pressure Vessel Code Section VIII (hereafter referred to as the 'Code'). However, the scope of the Code excludes vessels with internal or external operating pressure that do not exceed 15 pounds per square inch gauge (psig). Therefore, the requirements of the Code do not apply to vacuum systems provided that adequate pressure relief assures that the maximum internal pressure within the vacuum vessel is limited to less than 15 psig from all credible pressure sources, including failure scenarios. Vacuum vessels that cannot be protected from pressurization exceeding 15 psig are subject to the requirements of the Code. 10 CFR 851, Appendix A, Part 4, Pressure Safety, Section C addresses vacuum system requirements for such cases as follows: (c) When national consensus codes are not applicable (because of pressure range, vessel geometry, use of special materials, etc.), contractors must implement measures to provide equivalent protection and ensure a level of safety greater than or equal to the level of protection afforded by the ASME or applicable state or local code. Measures must include the following: (1) Design drawings, sketches, and calculations must be reviewed and approved by a qualified independent design professional (i.e., professional engineer). Documented organizational peer review is acceptable. (2) Qualified personnel must be used to perform examinations and inspections of materials, in-process fabrications, non-destructive tests, and acceptance test. (3) Documentation, traceability, and accountability must be maintained for each unique pressure vessel or system, including descriptions of design, pressure conditions, testing, inspection, operation, repair, and maintenance. The purpose of this guideline is to establish a set of expectations and recommendations which will satisfy the requirements for vacuum vessels in general and particularly when an equivalent level of safety as required by 10 CFR 851 must be provided. It should be noted that these guidelines are not binding on DOE Accelerator Laboratories and that other approaches may be equally acceptable in addressing the Part 851 requirements.

  11. accelerator system string: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    are being used for. Initially introduced to handle equipment builders' data, commercial DBMS are now being used in almost all areas of accelerators from on-line control to...

  12. Working Group Report on - Space Nuclear Power Systems and Nuclear...

    Energy Savers [EERE]

    Working Group Report on - Space Nuclear Power Systems and Nuclear Waste Technology R&D Working Group Report on - Space Nuclear Power Systems and Nuclear Waste Technology R&D "Even...

  13. A Software System for Modeling and Controlling Accelerator Physics Parameters at the Advanced Light Source

    E-Print Network [OSTI]

    Schachinger, L.C.

    2011-01-01T23:59:59.000Z

    and Controlling Accelerator Physics Parameters at theLight Source for accelerator physics studies and accelerator

  14. Advanced Vehicles Group: Center for Transportation Technologies and Systems

    SciTech Connect (OSTI)

    Not Available

    2008-08-01T23:59:59.000Z

    Describes R&D in advanced vehicle systems and components (e.g., batteries) by NREL's Advanced Vehicles Group.

  15. Designing Accelerator-Based Distributed Systems for High Performance M. Mustafa Rafique, Ali R. Butt

    E-Print Network [OSTI]

    Butt, Ali R.

    ), yielding highly power-efficient and cost-efficient designs, with per- formance exceeding 100 Gflops [1Designing Accelerator-Based Distributed Systems for High Performance M. Mustafa Rafique, Ali R general- purpose cores (e.g. x86, PowerPC) and computational accelerators (e.g. SIMD processors and GPUs

  16. AT2 DS II - Accelerator System Design (Part II) - CCC Video Conference

    ScienceCinema (OSTI)

    None

    2011-10-06T23:59:59.000Z

    Discussion Session - Accelerator System Design (Part II) Tutors: C. Darve, J. Weisend II, Ph. Lebrun, A. Dabrowski, U. Raich Video Conference with the CERN Control Center. Experts in the field of Accelerator science will be available to answer the students questions. This session will link the CCC and SA (using Codec VC).

  17. AT2 DS II - Accelerator System Design (Part II) - CCC Video Conference

    SciTech Connect (OSTI)

    None

    2010-12-17T23:59:59.000Z

    Discussion Session - Accelerator System Design (Part II) Tutors: C. Darve, J. Weisend II, Ph. Lebrun, A. Dabrowski, U. Raich Video Conference with the CERN Control Center. Experts in the field of Accelerator science will be available to answer the students questions. This session will link the CCC and SA (using Codec VC).

  18. Stochastic Systems Group MR Bias Correction and Reflectance

    E-Print Network [OSTI]

    Willsky, Alan S.

    . Fisher, M. Cetin, S. Haker, A. Willsky #12;Stochastic Systems Group Outline 1. Introduction 2. MR) · Both maps will have edges #12;Stochastic Systems Group Outline 1. Introduction 2. MR measurement modelStochastic Systems Group MR Bias Correction and Reflectance and Illumination Separation Ayres Fan

  19. Medical accelerator safety considerations: Report of AAPM Radiation Therapy Committee Task Group No. 35

    SciTech Connect (OSTI)

    Purdy, J.A.; Biggs, P.J.; Bowers, C.; Dally, E.; Downs, W.; Fraass, B.A.; Karzmark, C.J.; Khan, F.; Morgan, P.; Morton, R.

    1993-07-01T23:59:59.000Z

    Ensuring safe operation for a medical accelerator is a difficult task. Users must assume more responsibility in using contemporary equipment. Additionally, users must work closely with manufacturers in promoting the safe and effective use of such complex equipment. Complex treatment techniques and treatment modality changeover procedures merit detailed, unambiguous written procedural instruction at the control console. A thorough hands on training period after receiving instructions, and before assuming treatment responsibilities, is essential for all technologists. Unambiguous written instructions must also be provided to guide technologists in safe response when equipment malfunctions or exhibits unexpected behavior or after any component has been changed or readjusted. Technologists should be given a written list of the appropriate individuals to consult when unexpected machine behavior occurs. They should be assisted in identifying aberrant behavior of equipment. Many centers already provide this instruction, but others may not. Practiced response and discussion with technologists should be a part of an ongoing quality assurance program. An important aspect of a safety program is the need for continuous vigilance. Table III gives a summary of a comprehensive safety program for medical accelerators. Table IV gives a list of summary recommendations as an example of how one might mitigate the consequences of an equipment failure and improve procedures and operator response in the context of the environment described. Most of these recommendations can be implemented almost immediately at any individual treatment center.

  20. Application of JLab 12GeV helium refrigeration system for the FRIB accelerator at MSU

    SciTech Connect (OSTI)

    Ganni, V.; Knudsen, P.; Arenius, D. [Thomas Jefferson National Accelerator Facility, Newport News, VA 23606 (United States); Casagrande, F. [MSU-FRIB, East Lansing, MI 48824 (United States)

    2014-01-29T23:59:59.000Z

    The planned approach to have a turnkey helium refrigeration system for the MSU-FRIB accelerator system, encompassing the design, fabrication, installation and commissioning of the 4.5-K refrigerator cold box(es), cold compression system, warm compression system, gas management, oil removal and utility/ancillary systems, was found to be cost prohibitive. Following JLab’s suggestion, MSU-FRIB accelerator management made a formal request to evaluate the applicability of the recently designed 12GeV JLab cryogenic system for this application. The following paper will outline the findings and the planned approach for the FRIB helium refrigeration system.

  1. Application of JLab 12GeV helium refrigeration system for the FRIB accelerator at MSU

    SciTech Connect (OSTI)

    Ganni, Venkatarao [JLAB; Knudsen, Peter N. [JLAB; Arenius, Dana M. [JLAB; Casagrande, Fabio [Michigan State University

    2014-01-01T23:59:59.000Z

    The planned approach to have a turnkey helium refrigeration system for the MSU-FRIB accelerator system, encompassing the design, fabrication, installation and commissioning of the 4.5-K refrigerator cold box(es), cold compression system, warm compression system, gas management, oil removal and utility/ancillary systems, was found to be cost prohibitive. Following JLab’s suggestion, MSU-FRIB accelerator management made a formal request to evaluate the applicability of the recently designed 12GeV JLab cryogenic system for this application. The following paper will outline the findings and the planned approach for the FRIB helium refrigeration system.

  2. accelerator-driven transmutation system: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    plan is considered Yu Qi; Ouyang Hua Fu; Xu Tao Guang 2001-01-01 7 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  3. accelerator-driven subcritical systems: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  4. accelerator-driven transmutation systems: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    plan is considered Yu Qi; Ouyang Hua Fu; Xu Tao Guang 2001-01-01 7 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  5. Development of repetitive railgun pellet accelerator and steady-state pellet supply system

    SciTech Connect (OSTI)

    Oda, Y.; Onozuka, M.; Azuma, K. [Mitsubishi Heavy Industries, Ltd., Kobe (Japan); Kasai, S.; Hasegawa, K. [Japan Atomic Energy Research Inst., Naka (Japan)

    1995-12-31T23:59:59.000Z

    A railgun system for repetitive high-speed pellet acceleration and steady-state pellet supply system has been developed and investigated. Using a 2m-long railgun system, the hydrogen pellet was accelerated to 2.6km/sec by the supplied energy of 1.7kJ. It is expected that the hydrogen pellet can be accelerated to 3km/sec using the present pneumatic pellet accelerator and a 2m-long augment railgun. Screw-driven hydrogen-isotope filament extruding system has been fabricated and will be tested to examine its applicability to the steady-state extrusion of the solid hydrogen-isotope filament.

  6. Vision, Robotics and Images Research Group, UFPR 1 GPU-accelerated PSF Estimation with a

    E-Print Network [OSTI]

    with a Cooperative Particle Swarm Optimization Kiepenheuer Institute for Solar Physics Freiburg, 04.06.2013 Peter F) Kiepenheuer Institute for Solar Physics, Freiburg, Germany #12;Vision, Robotics and Images Research Group on the dynamics of a bird flock Find good "food" regions in search space Does not guaranty optimal solution

  7. Managing System of Systems Requirements with a Requirements Screening Group

    SciTech Connect (OSTI)

    Ronald R. Barden

    2012-07-01T23:59:59.000Z

    Figuring out an effective and efficient way to manage not only your Requirement’s Baseline, but also the development of all your individual requirements during a Program’s/Project’s Conceptual and Development Life Cycle Stages can be both daunting and difficult. This is especially so when you are dealing with a complex and large System of Systems (SoS) Program with potentially thousands and thousands of Top Level Requirements as well as an equal number of lower level System, Subsystem and Configuration Item requirements that need to be managed. This task is made even more overwhelming when you have to add in integration with multiple requirements’ development teams (e.g., Integrated Product Development Teams (IPTs)) and/or numerous System/Subsystem Design Teams. One solution for tackling this difficult activity on a recent large System of Systems Program was to develop and make use of a Requirements Screening Group (RSG). This group is essentially a Team made up of co-chairs from the various Stakeholders with an interest in the Program of record that are enabled and accountable for Requirements Development on the Program/Project. The RSG co-chairs, often with the help of individual support team, work together as a Program Board to monitor, make decisions on, and provide guidance on all Requirements Development activities during the Conceptual and Development Life Cycle Stages of a Program/Project. In addition, the RSG can establish and maintain the Requirements Baseline, monitor and enforce requirements traceability across the entire Program, and work with other elements of the Program/Project to ensure integration and coordination.

  8. Direct measurement of the cosmic acceleration by 21cm absorption systems

    E-Print Network [OSTI]

    Yu, Hao-Ran; Pen, Ue-Li

    2013-01-01T23:59:59.000Z

    So far there is only indirect evidence that the universe is undergoing an accelerated expansion. The evidence for cosmic acceleration is based on the observation of different objects at different distances, and requires invoking the Copernican cosmological principle, and Einstein's equations of motion. We examine the direct observability using recession velocity drifts (Sandage-Loeb effect) of 21cm hydrogen absorption systems in upcoming radio surveys. This measures the change in velocity of the {\\it same} objects separate by a time interval and is a model-independent measure of acceleration. We forecast that for a CHIME-like survey with a decade time span, we can detect the acceleration of a $\\Lambda$CDM universe with $\\sim 6\\sigma$ confidence. This acceleration test requires modest data analysis and storage changes from the normal processing, and cannot be recovered retroactively.

  9. Hydrogen Storage Systems Analysis Working Group Meeting: Summary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Summary of June 11, 2008, biannual meeting of the Hydrogen Storage Systems Analysis Working Group. ssawgsummaryreport0608.pdf More Documents & Publications Hydrgoen Storage...

  10. Hydrogen Storage Systems Analysis Working Group Meeting: Summary...

    Broader source: Energy.gov (indexed) [DOE]

    Hydrogen Storage Systems Analysis Working Group Meeting Argonne DC Offices L'Enfant Plaza, Washington, DC December 4, 2007 SUMMARY REPORT Compiled by Romesh Kumar Argonne National...

  11. Advanced Klystrons for High Efficiency Accelerator Systems - Final Report

    SciTech Connect (OSTI)

    Read, Michael; Ives, Robert Lawrence

    2014-03-26T23:59:59.000Z

    This program explored tailoring of RF pulses used to drive accelerator cavities. Simulations indicated that properly shaping the pulse risetime to match accelerator cavity characteristics reduced reflected power and increased total efficiency. Tailoring the pulse requires a high power, gridded, klystron to shape the risetime while also controlling the beam current. The Phase I program generated a preliminary design of a gridded electron gun for a klystron producing 5-10 MW of RF power. This required design of a segmented cathode using Controlled Porosity Reservoir cathodes to limit power deposition on the grid. The program was successful in computationally designing a gun producing a high quality electron beam with grid control. Additional analysis of pulse tailoring indicated that technique would only be useful for cavity drive pulses that were less than approximately 2-3 times the risetime. Otherwise, the efficiency gained during the risetime of the pulse became insignificant when considering the efficiency over the entire pulse. Consequently, it was determined that a Phase II program would not provide sufficient return to justify the cost. Never the less, other applications for a high power gridded gun are currently being pursued. This klystron, for example, would facilitate development inverse Comptom x-ray sources by providing a high repetition rate (10 -100 kHz) RF source.

  12. Disposition of nuclear waste using subcritical accelerator-driven systems

    SciTech Connect (OSTI)

    Venneri, F.; Li, N.; Williamson, M.; Houts, M.; Lawrence, G.

    1998-12-31T23:59:59.000Z

    Spent fuel from nuclear power plants contains large quantities of Pu, other actinides, and fission products (FP). This creates challenges for permanent disposal because of the long half-lives of some isotopes and the potential for diversion of the fissile material. Two issues of concern for the US repository concept are: (1) long-term radiological risk peaking tens-of-thousands of years in the future; and (2) short-term thermal loading (decay heat) that limits capacity. An accelerator-driven neutron source can destroy actinides through fission, and can convert long-lived fission products to shorter-lived or stable isotopes. Studies over the past decade have established that accelerator transmutation of waste (ATW) can have a major beneficial impact on the nuclear waste problem. Specifically, the ATW concept the authors are evaluating: (1) destroys over 99.9% of the actinides; (2) destroys over 99.9% of the Tc and I; (3) separates Sr-90 and Cs-137; (4) separates uranium from the spent fuel; (5) produces electric power.

  13. Thermal Systems Group; Electricity, Resources, & Building Systems Integration (ERBSI) (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-11-01T23:59:59.000Z

    Factsheet developed to describe the activites of the Thermal Systems Group within NREL's Electricity, Resources, and Buildings Systems Integration center.

  14. Transportation Planning & Decision Science Group Transportation Systems Research Group Diane Davidson Keith Kahl

    E-Print Network [OSTI]

    Transportation Planning & Decision Science Group Transportation Systems Research Group Diane Davidson Keith Kahl 865-946-1475 865-946-1236 Center for Transportation Analysis News Oak Ridge National to members of the Kentucky Transportation Cabinet and the Kentucky Transportation Center. The purpose

  15. Transportation Planning & Decision Science Group Transportation Systems Research Group Diane Davidson Keith Kahl

    E-Print Network [OSTI]

    Transportation Planning & Decision Science Group Transportation Systems Research Group Diane Davidson Keith Kahl 865-946-1475 865-946-1236 Center for Transportation Analysis News Oak Ridge National, during the Chairman's Luncheon at the 92nd Annual Transportation Research Board (TRB) Meeting

  16. accelerator control system: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    control system is largely based on standard industrial hardware and software components. SIEMENS Simatic S7-300 programmable logic controllers have been used as equipment...

  17. accelerator controls system: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    control system is largely based on standard industrial hardware and software components. SIEMENS Simatic S7-300 programmable logic controllers have been used as equipment...

  18. accelerator control systems: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    control system is largely based on standard industrial hardware and software components. SIEMENS Simatic S7-300 programmable logic controllers have been used as equipment...

  19. HIGH-POWER PRECISION CURRENT SUPPLY IST2-1000M FOR ELEMENTS OF MAGNETIC SYSTEMS OF ACCELERATORS AND

    E-Print Network [OSTI]

    Kozak, Victor R.

    HIGH-POWER PRECISION CURRENT SUPPLY IST2-1000M FOR ELEMENTS OF MAGNETIC SYSTEMS OF ACCELERATORS. These supplies are intended to power magnetic systems of accelerators, requiring high stability and low ripples current at non-inductive load % 0,02 Rate of current raise without disturbing operation of the system

  20. Protecting Accelerator Control Systems in the Face of Sophisticated Cyber Attacks

    SciTech Connect (OSTI)

    Hartman, Steven M [ORNL] [ORNL

    2012-01-01T23:59:59.000Z

    Cyber security for industrial control systems has received significant attention in the past two years. The news coverage of the Stuxnet attack, believed to be targeted at the control system for a uranium enrichment plant, brought the issue to the attention of news media and policy makers. This has led to increased scrutiny of control systems for critical infrastructure such as power generation and distribution, and industrial systems such as chemical plants and petroleum refineries. The past two years have also seen targeted network attacks aimed at corporate and government entities including US Department of Energy National Laboratories. Both of these developments have potential repercussions for the control systems of particle accelerators. The need to balance risks from potential attacks with the operational needs of an accelerator present a unique challenge for the system architecture and access model.

  1. Phase and amplitude control system for Stanford Linear Accelerator

    SciTech Connect (OSTI)

    Yoo, S.J.

    1983-09-26T23:59:59.000Z

    The computer controlled phase and amplitude detection system measures the instantaneous phase and amplitude of a 1 micro-second 2856 MHz rf pulse at a 180 Hz rate. This will be used for phase feedback control, and also for phase and amplitude jitter measurement. The program, which was originally written by John Fox and Keith Jobe, has been modified to improve the function of the system. The software algorithms used in the measurement are described, as is the performance of the prototype phase and amplitude detector system.

  2. BREAKOUT GROUP 3: HIGH TEMP (SOFC) SYSTEM AND BOP PARTICIPANTS

    E-Print Network [OSTI]

    BREAKOUT GROUP 3: HIGH TEMP (SOFC) SYSTEM AND BOP PARTICIPANTS NAME ORGANIZATION Dan Birmingham (SOFC) AND BOP KEY TECHNICAL BARRIERS SEALS DURABILITY/RELIABILITY/DEGRADATION CONTAMINANTS · Seals processes FC Solicitation Workshop 2 March 2010 #12;BREAKOUT GROUP 3: HIGH TEMP (SOFC) AND BOP CRITICAL R

  3. Hydrogen Storage Systems Analysis Working Group Meeting Argonne DC Offices

    E-Print Network [OSTI]

    Hydrogen Storage Systems Analysis Working Group Meeting Argonne DC Offices L'Enfant Plaza, Washington, DC December 4, 2007 SUMMARY REPORT Compiled by Romesh Kumar Argonne National Laboratory Working Group Meeting December 4, 2007 Argonne DC Offices, L'Enfant Plaza, Washington, DC Meeting

  4. Asynchronous data change notification between database server and accelerator controls system

    SciTech Connect (OSTI)

    Fu, W.; Morris, J.; Nemesure, S.

    2011-10-10T23:59:59.000Z

    Database data change notification (DCN) is a commonly used feature. Not all database management systems (DBMS) provide an explicit DCN mechanism. Even for those DBMS's which support DCN (such as Oracle and MS SQL server), some server side and/or client side programming may be required to make the DCN system work. This makes the setup of DCN between database server and interested clients tedious and time consuming. In accelerator control systems, there are many well established software client/server architectures (such as CDEV, EPICS, and ADO) that can be used to implement data reflection servers that transfer data asynchronously to any client using the standard SET/GET API. This paper describes a method for using such a data reflection server to set up asynchronous DCN (ADCN) between a DBMS and clients. This method works well for all DBMS systems which provide database trigger functionality. Asynchronous data change notification (ADCN) between database server and clients can be realized by combining the use of a database trigger mechanism, which is supported by major DBMS systems, with server processes that use client/server software architectures that are familiar in the accelerator controls community (such as EPICS, CDEV or ADO). This approach makes the ADCN system easy to set up and integrate into an accelerator controls system. Several ADCN systems have been set up and used in the RHIC-AGS controls system.

  5. Collider-Accelerator Department/SNSRing Systems BROOKHAVENNATIONALLABORATORY

    E-Print Network [OSTI]

    shall be installed by Brookhaven National Laboratory (BNL) as part of a large magnet power system ANSI/IEEE C57 Distribution, Power and Regulating Transformers NFPA70 National ElectricCode IEEE 5ScienceAssociates Upton, New York 11973 SPEC. SNS-OO9 December 14, 1999 SDecification for Iuiection Bumo Power Suoolies "T

  6. Data acquisition system at the RIKEN accelerator facility

    SciTech Connect (OSTI)

    Ichihara, T.; Inamura, T.; Wada, T.; Ishihara, M. (RIKEN Accelerator facility 2-1, Hirosawa, Wako, 351-01 (JP))

    1989-10-01T23:59:59.000Z

    This paper describes data acquisition system using J11 CPU (Starburst 2180 ACC) and Micro VAX II. Each event is processed by J11 CPU. Buffered data is transferred to Micro VAX II through Kinetic parallel bus. The executable image on J11 is builded on Micro VAX II using VAX/RSX and down-line loaded via CAMAC dataway.

  7. ACCELERATOR TEST FACILITY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    LABORATORY PHYSICS DEPARTMENT Effective: 04012004 Page 1 of 2 Subject: Accelerator Test Facility - Linear Accelerator General Systems Guide Prepared by: Michael Zarcone...

  8. Accelerating Acceptance of Fuel Cell Backup Power Systems - Final Report

    SciTech Connect (OSTI)

    Petrecky, James; Ashley, Christopher

    2014-07-21T23:59:59.000Z

    Since 2001, Plug Power has installed more than 800 stationary fuel cell systems worldwide. Plug Power’s prime power systems have produced approximately 6.5 million kilowatt hours of electricity and have accumulated more than 2.5 million operating hours. Intermittent, or backup, power products have been deployed with telecommunications carriers and government and utility customers in North and South America, Europe, the United Kingdom, Japan and South Africa. Some of the largest material handling operations in North America are currently using the company’s motive power units in fuel cell-powered forklifts for their warehouses, distribution centers and manufacturing facilities. The low-temperature GenSys fuel cell system provides remote, off-grid and primary power where grid power is unreliable or nonexistent. Built reliable and designed rugged, low- temperature GenSys delivers continuous or backup power through even the most extreme conditions. Coupled with high-efficiency ratings, low-temperature GenSys reduces operating costs making it an economical solution for prime power requirements. Currently, field trials at telecommunication and industrial sites across the globe are proving the advantages of fuel cells—lower maintenance, fuel costs and emissions, as well as longer life—compared with traditional internal combustion engines.

  9. A proposed second harmonic acceleration system for the Intense Pulsed Neutron Source Rapid Cycling Synchrotron

    SciTech Connect (OSTI)

    Norem, J.; Brandeberry, F.; Rauchas, A.

    1983-08-01T23:59:59.000Z

    The Rapid Cycling Synchrotron (RCS) of the Intense Pulsed Neutron Source (IPNS) operating at Argonne National Laboratory is presently producing intensities of 2-2.5 x 10/sup 12/ protons per pulse (ppp) with the addition of a new ion source. This intensity is close to the space charge limit of the machine, estimated at about 3 x 10/sup 12/ ppp, depending somewhat on the available aperture. With the present good performance in mind, accelerator improvements are being directed at increasing beam intensities for neutron science, lowering acceleration losses to minimize activation, and gaining better control of the beam so that losses can be made to occur when and where they can be most easily controlled. On the basis of preliminary measurements, the authors are now proposing a third cavity for the RF system which would provide control of the longitudinal bunch shape during the cycle which would permit raising the effective space charge limit of the accelerator and reducing losses.

  10. Exposure of Polymeric Glazing Materials Using NREL's Ultra-Accelerated Weathering System (UAWS)

    SciTech Connect (OSTI)

    Bingham, C.; Jorgensen, G.; Wylie, A.

    2010-01-01T23:59:59.000Z

    NREL's Ultra-Accelerated Weathering System (UAWS) selectively reflects and concentrates natural sunlight ultraviolet irradiance below 475 nm onto exposed samples to provide accelerated weathering of materials while keeping samples within realistic temperature limits. This paper will explain the design and implementation of the UAWS which allow it to simulate the effect of years of weathering in weeks of exposure. Exposure chamber design and instrumentation will be discussed for both a prototype UAWS used to test glazing samples as well as a commercial version of UAWS. Candidate polymeric glazing materials have been subjected to accelerated exposure testing at a light intensity level of up to 50 UV suns for an equivalent outdoor exposure in Miami, FL exceeding 15 years. Samples include an impact modified acrylic, fiberglass, and polycarbonate having several thin UV-screening coatings. Concurrent exposure is carried out for identical sample sets at two different temperatures to allow thermal effects to be quantified along with resistance to UV.

  11. Cyber-Physical System Verification Embedded Systems Group

    E-Print Network [OSTI]

    Berns, Karsten

    (Felipe Bichued) 21 Introducing Simulation of Hybrid Systems with the Modelica Tool 32 #12;Cyber Physical

  12. G-NetMon: a GPU-accelerated network performance monitoring system

    SciTech Connect (OSTI)

    Wu, Wenji; DeMar, Phil; Holmgren, Don; Singh, Amitoj; /Fermilab

    2011-06-01T23:59:59.000Z

    At Fermilab, we have prototyped a GPU-accelerated network performance monitoring system, called G-NetMon, to support large-scale scientific collaborations. In this work, we explore new opportunities in network traffic monitoring and analysis with GPUs. Our system exploits the data parallelism that exists within network flow data to provide fast analysis of bulk data movement between Fermilab and collaboration sites. Experiments demonstrate that our G-NetMon can rapidly detect sub-optimal bulk data movements.

  13. Centrifugal accelerator, system and method for removing unwanted layers from a surface

    DOE Patents [OSTI]

    Foster, Christopher A. (Clinton, TN); Fisher, Paul W. (Heiskell, TN)

    1995-01-01T23:59:59.000Z

    A cryoblasting process having a centrifugal accelerator for accelerating frozen pellets of argon or carbon dioxide toward a target area utilizes an accelerator throw wheel designed to induce, during operation, the creation of a low-friction gas bearing within internal passages of the wheel which would otherwise retard acceleration of the pellets as they move through the passages. An associated system and method for removing paint from a surface with cryoblasting techniques involves the treating, such as a preheating, of the painted surface to soften the paint prior to the impacting of frozen pellets thereagainst to increase the rate of paint removal. A system and method for producing large quantities of frozen pellets from a liquid material, such as liquid argon or carbon dioxide, for use in a cryoblasting process utilizes a chamber into which the liquid material is introduced in the form of a jet which disintegrates into droplets. A non-condensible gas, such as inert helium or air, is injected into the chamber at a controlled rate so that the droplets freeze into bodies of relatively high density.

  14. Equivalence of Control Systems with Linear Systems on Lie Groups and Homogeneous Spaces

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Equivalence of Control Systems with Linear Systems on Lie Groups and Homogeneous Spaces Philippe of geometric control theory arguments. Keywords: Lie groups; Homogeneous spaces; Linear systems; Com- plete JOUAN 28th November 2008 Abstract The aim of this paper is to prove that a control affine system

  15. Accelerator Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisiting the TWP TWP Related LinksATHENA couldAbout BudgetAboutNewsOSTI, USAccelerator

  16. Image Fusion for MR Bias Stochastic Systems Group

    E-Print Network [OSTI]

    Willsky, Alan S.

    We can target T1 and T2 through appropriate selection of TE and TR. #12;Image Reconstruction The MRImage Fusion for MR Bias Correction Ayres Fan Stochastic Systems Group Joint work with W. Wells, J. Fisher, M. Cetin, S. Haker, A. Willsky, B. Mulkern #12;Magnetic Resonance The magnetic resonance (MR

  17. Charles J. Vrsmarty & the UNH Water Systems Analysis Group

    E-Print Network [OSTI]

    Slatton, Clint

    .1 billion people lack clean drinking water 2.6 billion people lack basic sanitationCharles J. Vörösmarty & the UNH Water Systems Analysis Group Fall Water Institute Seminar Series Corridor #12;Goals for This Discussion · Describe chief forces shaping the contemporary and future water

  18. A three dimensional simulation of a thermal experiment conducted on an accelerator driven system target model concept

    E-Print Network [OSTI]

    Pratt, Preston Persley

    2003-01-01T23:59:59.000Z

    Accelerator transmutation of waste (ATW) is a new concept that would destroy actinides in spent fuel and produce electrical power. This study explores the possibility of modeling the thermo-hydraulics of this system with computational fluid...

  19. Finite Density Matrix Renormalisation Group Algorithm for Anyonic Systems

    E-Print Network [OSTI]

    Robert N. C. Pfeifer; Sukhwinder Singh

    2015-05-01T23:59:59.000Z

    The numerical study of anyonic systems is known to be highly challenging due to their non-bosonic, non-fermionic particle exchange statistics, and with the exception of certain models for which analytical solutions exist, very little is known about their collective behaviour as a result. Meanwhile, the density matrix renormalisation group (DMRG) algorithm is an exceptionally powerful numerical technique for calculating the ground state of a low-dimensional lattice Hamiltonian, and has been applied to the study of bosonic, fermionic, and group-symmetric systems. The recent development of a tensor network formulation for anyonic systems opened up the possibility of studying these systems using algorithms such as DMRG, though this has proved challenging both in terms of programming complexity and computational cost. This paper presents the implementation of DMRG for finite anyonic systems, including a detailed scheme for the implementation of anyonic tensors with optimal scaling of computational cost. The anyonic DMRG algorithm is demonstrated by calculating the ground state energy of the Golden Chain, which has become the benchmark system for the numerical study of anyons, and is shown to produce results comparable to those of the anyonic TEBD algorithm and superior to the variationally optimised anyonic MERA, at far lesser computational cost.

  20. Proposed second harmonic acceleration system for the intense pulsed neutron source rapid cycling synchrotron

    SciTech Connect (OSTI)

    Norem, J.; Brandeberry, F.; Rauchas, A.

    1983-01-01T23:59:59.000Z

    The Rapid Cycling Synchrotron (RCS) of the Intense Pulsed Neutron Source (IPNS) operating at Argonne National Laboratory is presently producing intensities of 2 to 2.5 x 10/sup 12/ protons per pulse (ppp) with the addition of a new ion source. This intensity is close to the space charge limit of the machine, estimated at approx.3 x 10/sup 12/ ppp, depending somewhat on the available aperture. With the present good performance in mind, accelerator improvements are being directed at: (1) increasing beam intensities for neutron science; (2) lowering acceleration losses to minimize activation; and (3) gaining better control of the beam so that losses can be made to occur when and where they can be most easily controlled. On the basis of preliminary measurements, we are now proposing a third cavity for the RF systems which would provide control of the longitudinal bunch shape during the cycle which would permit raising the effective space charge limit of the accelerator and reducing losses.

  1. Models of f(R) Cosmic Acceleration that Evade Solar-System Tests

    E-Print Network [OSTI]

    Wayne Hu; Ignacy Sawicki

    2007-05-08T23:59:59.000Z

    We study a class of metric-variation f(R) models that accelerates the expansion without a cosmological constant and satisfies both cosmological and solar-system tests in the small-field limit of the parameter space. Solar-system tests alone place only weak bounds on these models, since the additional scalar degree of freedom is locked to the high-curvature general-relativistic prediction across more than 25 orders of magnitude in density, out through the solar corona. This agreement requires that the galactic halo be of sufficient extent to maintain the galaxy at high curvature in the presence of the low-curvature cosmological background. If the galactic halo and local environment in f(R) models do not have substantially deeper potentials than expected in LCDM, then cosmological field amplitudes |f_R| > 10^{-6} will cause the galactic interior to evolve to low curvature during the acceleration epoch. Viability of large-deviation models therefore rests on the structure and evolution of the galactic halo, requiring cosmological simulations of f(R) models, and not directly on solar-system tests. Even small deviations that conservatively satisfy both galactic and solar-system constraints can still be tested by future, percent-level measurements of the linear power spectrum, while they remain undetectable to cosmological-distance measures. Although we illustrate these effects in a specific class of models, the requirements on f(R) are phrased in a nearly model-independent manner.

  2. Cavity beam position monitor system for the Accelerator Test Facility 2

    SciTech Connect (OSTI)

    Kim, Y.I.; /Kyungpook Natl. U.; Ainsworth, R.; /Royal Holloway, U. of London; Aryshev, A.; /KEK, Tsukuba; Boogert, S.T.; Boorman, G.; /Royal Holloway, U. of London; Frisch, J.; /SLAC; Heo, A.; /Kyungpook Natl. U.; Honda, Y.; /KEK, Tsukuba; Hwang, W.H.; Huang, J.Y.; /Pohang Accelerator Lab.; Kim, E-S.; /Kyungpook Natl. U. /Pohang Accelerator Lab. /Royal Holloway, U. of London /KEK, Tsukuba

    2012-04-02T23:59:59.000Z

    The Accelerator Test Facility 2 (ATF2) is a scaled demonstrator system for final focus beam lines of linear high energy colliders. This paper describes the high resolution cavity beam position monitor (BPM) system, which is a part of the ATF2 diagnostics. Two types of cavity BPMs are used, C-band operating at 6.423 GHz, and S-band at 2.888 GHz with an increased beam aperture. The cavities, electronics, and digital processing are described. The resolution of the C-band system with attenuators was determined to be approximately 250 nm and 1 {mu}m for the S-band system. Without attenuation the best recorded C-band cavity resolution was 27 nm.

  3. Transmutation of {sup 129}I Using an Accelerator-Driven System

    SciTech Connect (OSTI)

    Nishihara, Kenji; Takano, Hideki [Japan Atomic Energy Research Institute (Japan)

    2002-01-15T23:59:59.000Z

    A conceptual blanket design for {sup 129}I transmutation is proposed for an accelerator-driven system (ADS) that is designed to transmute minor actinides (MAs). In this ADS, 250 kg/yr of MA and 56 kg/yr of iodine are simultaneously transmuted, and they correspond to the quantities generated from {approx}10 units of existing light water reactors. Furthermore, an introduction scenario and the benefit of iodine transmutation are studied for future introduction of fast breeder reactors. It is shown that the transmutation of iodine benefits the concept of underground disposal.

  4. Comparative Microbial Genomics group CenterforBiologicalSequenceanalysisDepartmentofSystemsBiology

    E-Print Network [OSTI]

    Ussery, David W.

    Comparative Microbial Genomics group CenterforBiologicalSequenceanalysisDepartmentofSystemsBiology Visualisation of Large Amounts of Data Dave Ussery 27 February, 2008 #12;Comparative Microbial Genomics group CenterforBiologicalSequenceanalysisDepartmentofSystemsBiology #12;Comparative Microbial Genomics group

  5. A hybrid data acquisition system for magnetic measurements of accelerator magnets

    SciTech Connect (OSTI)

    Wang, X.; Hafalia, R.; Joseph, J.; Lizarazo, J.; Martchevsky, M.; Sabbi, G. L.

    2011-06-03T23:59:59.000Z

    A hybrid data acquisition system was developed for magnetic measurement of superconducting accelerator magnets at LBNL. It consists of a National Instruments dynamic signal acquisition (DSA) card and two Metrolab fast digital integrator (FDI) cards. The DSA card records the induced voltage signals from the rotating probe while the FDI cards records the flux increment integrated over a certain angular step. This allows the comparison of the measurements performed with two cards. In this note, the setup and test of the system is summarized. With a probe rotating at a speed of 0.5 Hz, the multipole coefficients of two magnets were measured with the hybrid system. The coefficients from the DSA and FDI cards agree with each other, indicating that the numerical integration of the raw voltage acquired by the DSA card is comparable to the performance of the FDI card in the current measurement setup.

  6. Pyrochemical separations technologies envisioned for the U. S. accelerator transmutation of waste system

    SciTech Connect (OSTI)

    Laidler, J. J.

    2000-02-17T23:59:59.000Z

    A program has been initiated for the purpose of developing the chemical separations technologies necessary to support a large Accelerator Transmutation of Waste (ATW) system capable of dealing with the projected inventory of spent fuel from the commercial nuclear power stations in the United States. The baseline process selected combines aqueous and pyrochemical processes to enable the efficient separation of uranium, technetium, iodine, and the transuranic elements from LWR spent fuel. The diversity of processing methods was chosen for both technical and economic factors. A six-year technology evaluation and development program is foreseen, by the end of which an informed decision can be made on proceeding with demonstration of the ATW system.

  7. Group quantization of parametrized systems I. Time levels

    E-Print Network [OSTI]

    P. Hajicek

    1995-04-08T23:59:59.000Z

    A method of quantizing parametrized systems is developed that is based on a kind of ``gauge invariant'' quantities---the so-called perennials (a perennial must also be an ``integral of motion''). The problem of time in its particular form (frozen time formalism, global problem of time, multiple choice problem) is met, as well as the related difficulty characteristic for this type of theory: the paucity of perennials. The present paper is an attempt to find some remedy in the ideas on ``forms of relativistic dynamics'' by Dirac. Some aspects of Dirac's theory are generalized to all finite-dimensional first-class parametrized systems. The generalization is based on replacing the Poicar\\'{e} group and the algebra of its generators as used by Dirac by a canonical group of symmetries and by an algebra of elementary perennials. A number of insights is gained; the following are the main results. First, conditions are revealed under which the time evolution of the ordinary quantum mechanics, or a generalization of it, can be constructed. The construction uses a kind of gauge and time choice and it is described in detail. Second, the theory is structured so that the quantum mechanics resulting from different choices of gauge and time are compatible. Third, a practical way is presented of how a broad class of problems can be solved without the knowledge of explicit form of perennials.

  8. AN ACCELERATOR-BASED NEUTRON MICROBEAM SYSTEM FOR STUDIES OF RADIATION EFFECTS

    E-Print Network [OSTI]

    Brenner, David Jonathan

    and David J. Brenner1 1 Radiological Research Accelerator Facility, Columbia University, Irvington, NY 10533 2010 A novel neutron microbeam is being developed at the Radiological Research Accelerator Facility on existing microbeam tech- niques at the Radiological Research Accelerator Facility (RARAF) of Columbia

  9. Laser-based proton acceleration on ultra-thin foil with a 100 TW class high intensity laser system

    E-Print Network [OSTI]

    Marjoribanks, Robin S.

    of electromagnetic fields in plasma, isotopes production or hadron therapy. The 100 TW class laser systemLaser-based proton acceleration on ultra-thin foil with a 100 TW class high intensity laser system. To characterize the plasma expansion, we monitor it with an imaging technique using a femtosecond laser probe

  10. Design and implementation of a Client-Server System for Acquiring Beam Intensity Data from High Energy Accelerators at CERN

    E-Print Network [OSTI]

    Topaloudis, A; Bellas, N; Jensen, L

    The world’s largest research center in the domain of High Energy Physics (HEP) is the European Organization for Nuclear Research (CERN) whose main goal is to accelerate particles through a sequence of acceleratorsaccelerator complex – and bring them into collision in order to study the fundamental elements of matter and the forces acting between them. For controlling the accelerator complex, CERN needs several diagnostic tools to provide information about the beam’s attributes and one such system is the Fast Beam Current Transformer (FBCT) measuring system that provides bunch-by-bunch and total beam intensity information. The current hardware and firmware of the FBCT system has certain issues and lacks diagnostics as a lot of the calculations are done in an FPGA. In order to improve on this, the firmware was redesigned and simplified in order to increase its capabilities and provide the base of a unified FBCT measuring system that could be installed in several of CERN’s accelerator complex’s pa...

  11. Physically Based Rendering Intersection Acceleration

    E-Print Network [OSTI]

    Kazhdan, Michael

    Physically Based Rendering (600.657) Intersection Acceleration #12;Intersection Testing Accelerated partitions: Group objects into clusters Cluster volumes may overlap #12;Uniform (Voxel) Grid Acceleration Acceleration · Trace rays through grid cells ­ Fast ­ Incremental A B C D E F Only check primitives

  12. Proposal for the award of a contract for the design, supply, installation and commissioning of Heating, Ventilation and Air-Conditioning (HVAC) systems for the PS accelerator infrastructure

    E-Print Network [OSTI]

    2012-01-01T23:59:59.000Z

    Proposal for the award of a contract for the design, supply, installation and commissioning of Heating, Ventilation and Air-Conditioning (HVAC) systems for the PS accelerator infrastructure

  13. Accelerator System Model (ASM) user manual with physics and engineering model documentation. ASM version 1.0

    SciTech Connect (OSTI)

    NONE

    1993-07-01T23:59:59.000Z

    The Accelerator System Model (ASM) is a computer program developed to model proton radiofrequency accelerators and to carry out system level trade studies. The ASM FORTRAN subroutines are incorporated into an intuitive graphical user interface which provides for the {open_quotes}construction{close_quotes} of the accelerator in a window on the computer screen. The interface is based on the Shell for Particle Accelerator Related Codes (SPARC) software technology written for the Macintosh operating system in the C programming language. This User Manual describes the operation and use of the ASM application within the SPARC interface. The Appendix provides a detailed description of the physics and engineering models used in ASM. ASM Version 1.0 is joint project of G. H. Gillespie Associates, Inc. and the Accelerator Technology (AT) Division of the Los Alamos National Laboratory. Neither the ASM Version 1.0 software nor this ASM Documentation may be reproduced without the expressed written consent of both the Los Alamos National Laboratory and G. H. Gillespie Associates, Inc.

  14. Group Recommender Systems: New Perspectives in the Social Web

    E-Print Network [OSTI]

    Cantador, Iván

    , the explosive growth of online communities, their increasing activ- ity and collected data, lift boundaries a movie or TV show to watch by a particular group of people (a couple, a family, a group of friends

  15. Final technical report [ACCELERATED MOLECULAR DYNAMICS SIMULATIONS OF REACTIVE HYDROCARBON SYSTEMS

    SciTech Connect (OSTI)

    Stuart, Steven J.

    2014-02-25T23:59:59.000Z

    The research activities in this project consisted of four different sub-projects. Three different accelerated dynamics techniques (parallel replica dynamics, hyperdynamics, and temperature-accelerated dynamics) were applied to the modeling of pyrolysis of hydrocarbons. In addition, parallel replica dynamics was applied to modeling of polymerization.

  16. Fuels Performance Group: Center for Transportation Technologies and Systems

    SciTech Connect (OSTI)

    Not Available

    2008-08-01T23:59:59.000Z

    Describes R&D and analysis in advanced petroleum-based and non-petroleum-based transportation fuels done by NREL's Fuels Performance Group.

  17. G-NetMon: A GPU-accelerated Network Performance Monitoring System for Large Scale Scientific Collaborations

    SciTech Connect (OSTI)

    Wu, Wenji; DeMar, Phil; Holmgren, Don; Singh, Amitoj; Pordes, Ruth; /Fermilab

    2011-08-01T23:59:59.000Z

    At Fermilab, we have prototyped a GPU-accelerated network performance monitoring system, called G-NetMon, to support large-scale scientific collaborations. Our system exploits the data parallelism that exists within network flow data to provide fast analysis of bulk data movement between Fermilab and collaboration sites. Experiments demonstrate that our G-NetMon can rapidly detect sub-optimal bulk data movements.

  18. Exhaust system having a gold-platinum group metal catalyst

    DOE Patents [OSTI]

    Ragle, Christie Susan (Havana, IL); Silver, Ronald G. (Peoria, IL); Zemskova, Svetlana Mikhailovna (Edelstein, IL); Eckstein, Colleen J. (Metamora, IL)

    2011-12-06T23:59:59.000Z

    A method of providing an exhaust treatment device is disclosed. The method includes applying a catalyst including gold and a platinum group metal to a particulate filter. The concentration of the gold and the platinum group metal is sufficient to enable oxidation of carbon monoxide and nitric oxide.

  19. The Cost of Adding Security Services to Group Communication Systems Cristina NitaRotaru

    E-Print Network [OSTI]

    Amir, Yair

    that handles every possible combination of network events. Rather it will focus on the performance evaluationThe Cost of Adding Security Services to Group Communication Systems #3; Cristina Nita sender to many receivers are based on a group communication model. Group communication systems are used

  20. The Cost of Adding Security Services to Group Communication Systems Cristina Nita-Rotaru

    E-Print Network [OSTI]

    Amir, Yair

    that handles every possible combination of network events. Rather it will focus on the performance evaluationThe Cost of Adding Security Services to Group Communication Systems Cristina Nita-Rotaru Advisor to many receivers are based on a group communication model. Group communication systems are used

  1. CESR Test Accelerator

    E-Print Network [OSTI]

    Rubin, David L

    2013-01-01T23:59:59.000Z

    The Cornell Electron Storage Ring (CESR) was reconfigured in 2008 as a test accelerator to investigate the physics of ultra-low emittance damping rings. During the approximately 40 days/year available for dedicated operation as a test accelerator, specialized instrumentation is used to measure growth and mitigation of the electron cloud, emittance growth due to electron cloud, intra-beam scattering, and ions, and single and multi-bunch instabilities generated by collective effects. The flexibility of the CESR guide field optics and the integration of accelerator modeling codes with the control system have made possible an extraordinary range of experiments. Findings at CesrTA with respect to electron cloud effects, emittance tuning techniques, and beam instrumentation for measuring electron cloud, beam sizes, and beam positions are the basis for much of the design of the ILC damping rings as documented in the ILC-Technical Design Report. The program has allowed the Cornell group to cultivate the kind of talen...

  2. A practical target system for accelerator-based BNCT which may effectively double the dose rate

    E-Print Network [OSTI]

    Brenner, David Jonathan

    . Randers-Pehrsona) and D. J. Brenner Center for Radiological Research, Radiological Research Accelerator Facility, Columbia University, Irvington, New York 10533 Received 27 May 1997; accepted for publication 31

  3. Entanglement of Accelerating Particles

    E-Print Network [OSTI]

    W. L. Ku; M. -C. Chu

    2007-09-03T23:59:59.000Z

    We study how the entanglement of a maximally entangled pair of particles is affected when one or both of the pair are uniformly accelerated, while the detector remains in an inertial frame. We find that the entanglement is unchanged if all degrees of freedom are considered. However, particle pairs are produced, and the entanglements of different bipartite systems may change with the acceleration. In particular, the entanglement between accelerating fermions is transferred preferentially to the produced antiparticles when the acceleration is large, and the entanglement transfer is complete when the acceleration approaches infinity. However, for scalar particles, no entanglement transfer to the antiparticles is observed.

  4. Conceptual design of minor actinides burner with an accelerator-driven subcritical system.

    SciTech Connect (OSTI)

    Cao, Y.; Gohar, Y. (Nuclear Engineering Division)

    2011-11-04T23:59:59.000Z

    In the environmental impact study of the Yucca Mountain nuclear waste repository, the limit of spent nuclear fuel (SNF) for disposal is assessed at 70,000 metric tons of heavy metal (MTHM), among which 63,000 MTHM are the projected SNF discharge from U.S. commercial nuclear power plants though 2011. Within the 70,000 MTHM of SNF in storage, approximately 115 tons would be minor actinides (MAs) and 585 tons would be plutonium. This study describes the conceptual design of an accelerator-driven subcritical (ADS) system intended to utilize (burn) the 115 tons of MAs. The ADS system consists of a subcritical fission blanket where the MAs fuel will be burned, a spallation neutron source to drive the fission blanket, and a radiation shield to reduce the radiation dose to an acceptable level. The spallation neutrons are generated from the interaction of a 1 GeV proton beam with a lead-bismuth eutectic (LBE) or liquid lead target. In this concept, the fission blanket consists of a liquid mobile fuel and the fuel carrier can be LBE, liquid lead, or molten salt. The actinide fuel materials are dissolved, mixed, or suspended in the liquid fuel carrier. Therefore, fresh fuel can be fed into the fission blanket to adjust its reactivity and to control system power during operation. Monte Carlo analyses were performed to determine the overall parameters of an ADS system utilizing LBE as an example. Steady-state Monte Carlo simulations were studied for three fission blanket configurations that are similar except that the loaded amount of actinide fuel in the LBE is either 5, 7, or 10% of the total volume of the blanket, respectively. The neutron multiplication factor values of the three configurations are all approximately 0.98 and the MA initial inventories are each approximately 10 tons. Monte Carlo burnup simulations using the MCB5 code were performed to analyze the performance of the three conceptual ADS systems. Preliminary burnup analysis shows that all three conceptual ADS systems consume about 1.2 tons of actinides per year and produce 3 GW thermal power, with a proton beam power of 25 MW. Total MA fuel that would be consumed in the first 10 years of operation is 9.85, 11.80, or 12.68 tons, respectively, for the systems with 5, 7, or 10% actinide fuel particles loaded in the LBE. The corresponding annual MA fuel transmutation rate after reaching equilibrium at 10 years of operation is 0.83, 0.94, or 1.02 tons/year, respectively. Assuming that the ADS systems can be operated for 35 full-power years, the total MAs consumed in the three ADS systems are 30.6, 35.3, and 37.2 tons, respectively. For the three configurations, it is estimated that 3.8, 3.3, or 3.1 ADS system units are required to utilize the entire 115 tons of MA fuel in the SNF inventory, respectively.

  5. Accelerators and the Accelerator Community

    E-Print Network [OSTI]

    Malamud, Ernest

    2009-01-01T23:59:59.000Z

    for a PhD in accelerator physics was by E.O. Lawrence.of Beams) organizes accelerator physics sessions at APSstudents specializing in accelerator physics are not being “

  6. Electrical Engineering Group Digital, analog, power, ASIC, FPGA, and embedded systems design

    E-Print Network [OSTI]

    Mojzsis, Stephen J.

    Electrical Engineering Group Digital, analog, power, ASIC, FPGA, and embedded systems design The Electrical Engineering (EE) Group at LASP has a broad range of technical expertise in the design, development, and test of space flight electrical systems. Engineers work closely with mission science, systems

  7. The accelerator automation application toolkit workshop presentations

    SciTech Connect (OSTI)

    Howell, J.A.; Bjorklund, E.A.; Clout, P.N.; Dalesio, L.R.; Kozubal, A.J.; Mottershead, C.T.; Rothrock, R.B.; Schaller, S.C.; Stuewe, R.B.; Westervelt, R.T.

    1988-01-01T23:59:59.000Z

    Over the past 18 months on the GTA project at Los Alamos, we have been developing tools for building control systems for accelerators. The first tool developed has already demonstrated greatly reduced requirements for conventional computer programming in applying control systems to an accelerator. Even in the early stages, this work has received considerable attention and the system is currently being investigated or used at several other institutes. Further tools are either in the conceptual design, design, or implementation phase. Over the same period, a group at CERN has been developing the ideas and design for a generic software kit for the application of a control system to accelerators. The CERN software kit also addresses the technical management and documentation aspects of control systems. The purpose of the AT Division effort and the CERN kit is to greatly simplify the implementation and lifetime maintenance of an accelerator control system. Experience has shown that accelerator control systems are also applicable to other experimental physics machines. The purpose of the workshop was to explore these ideas and developments as well as other relevant developments in the field, to verify the viability of the concepts, and to develop further the written specifications for some of the components of such a toolkit. We had draft specifications prepared prior to the workshop. 21 figs.

  8. Technology Evaluation and Integration Group: Center for Transportation Technologies and Systems

    SciTech Connect (OSTI)

    Not Available

    2008-08-01T23:59:59.000Z

    Fact sheet describes the specialized work done by NREL's Technology Evaluation and Integration Group in the Center for Transportation Technologies and Systems.

  9. Network Working Group S. Bryant, Ed. Request for Comments: 3985 Cisco Systems

    E-Print Network [OSTI]

    Wood, Lloyd

    Network Working Group S. Bryant, Ed. Request for Comments: 3985 Cisco Systems Category . . . . . . . . . . . . . . . . . . . . . . . . . 17 5. PW Encapsulation. . . . . . . . . . . . . . . . . . . . . . . 18 Bryant & Pate Standards Track

  10. TURKISH ACCELERATOR COMPLEX & STATUS OF TAC SASE FEL

    E-Print Network [OSTI]

    TURKISH ACCELERATOR COMPLEX & STATUS OF TAC SASE FEL Dr. Hatice DURAN YILDIZ On the Behalf of the TAC & TAC SASE-FEL Group DESY April 5, 2011 #12;2 Content Aim & Phases of the TAC Project TAC-TARLA Facility TARLA Resonator System TAC SASE-FEL Group Members & Duties TAC SASE-FEL Tentative Parameters

  11. Hydrogen Storage Systems Analysis Working Group Meeting: Summary...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    to bring together the DOE research community involved in systems analysis of hydrogen storage materials and processes. ssawgsummaryreport.pdf More Documents & Publications...

  12. Delayed neutron data and group parameters for 43 fissioning systems

    SciTech Connect (OSTI)

    Brady, M.C. (Oak Ridge National Lab., TN (USA)); England, T.R. (Los Alamos National Lab., NM (USA))

    1989-10-01T23:59:59.000Z

    The quality and quantity of delayed neutron precursor data have greatly improved over the past decade and a half. Supplementation of the data with model calculations and the use of models to extend the number of precursors to 271 is now practical. These data, along with other improved fission product parameters, permit direct calculations of aggregate behavior for many fissioning nuclides. The results can still be approximated using a few (usually six) temporal groups, including corresponding spectra, as in past practice for reactor physics. An extensive effort to provide a complete set of evaluated data is summarized, with an emphasis on its use to generate the temporal approximations; precursor data and group values are intended for inclusion in ENDF/B-VI.

  13. SATURATED FUSION SYSTEMS OVER 2-GROUPS BOB OLIVER AND JOANA VENTURA

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    SATURATED FUSION SYSTEMS OVER 2-GROUPS BOB OLIVER AND JOANA VENTURA Abstract. We develop methods-groups, fusion, simple groups. B. Oliver is partially supported by UMR 7539 of the CNRS. J. Ventura;2 BOB OLIVER AND JOANA VENTURA refer to Definition 2.3, Proposition 2.5, and Corollary 2.6 for more

  14. SATURATED FUSION SYSTEMS OVER 2-GROUPS BOB OLIVER AND JOANA VENTURA

    E-Print Network [OSTI]

    Ventura, Joana

    SATURATED FUSION SYSTEMS OVER 2-GROUPS BOB OLIVER AND JOANA VENTURA Abstract. We develop methods-groups, fusion, simple groups. B. Oliver is partially supported by UMR 7539 of the CNRS. J. Ventura is partially supported by FCT/POCTI/FEDER and grant PDCT/MAT/58497/2004. 1 #12;2 BOB OLIVER AND JOANA VENTURA

  15. EV Everywhere Workshop: Traction Drive Systems Breakout Group Report |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField Campaign:INEA :Work4/11 ENVIROISSUES ESF|OffInfrastructureGroup

  16. PNNL Technology Systems Analysis Group | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to: navigation, searchOfRoseConcernsCompanyPCN Technology Jump to: navigation,Analysis Group Jump

  17. PNNL Technology Systems Analysis Group | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual SiteofEvaluatingGroup |JilinLuOpenNorthOlympiaAnalysis) Jump to: navigation, search Logo:

  18. . ^ ^ L c O / ^ -Rise-R-497 Energy Systems Group

    E-Print Network [OSTI]

    of SO2 and N0X 12 2.4. An energy rationing mod^l for acute energy shortages 13 3. ENERGY TECHNOLOGY ASSESSMENT AND SYSTEMS ANALYSIS ... 14 3.1. Long-term prospects of energy technologies 14 3.2. Uncertainties"'-; .on systems 24 4.3. European Commission energy-economy models 27 4.4. Databases and other supporting

  19. Microelectromechanical acceleration-sensing apparatus

    DOE Patents [OSTI]

    Lee, Robb M. (Albuquerque, NM); Shul, Randy J. (Albuquerque, NM); Polosky, Marc A. (Albuquerque, NM); Hoke, Darren A. (Albuquerque, NM); Vernon, George E. (Rio Rancho, NM)

    2006-12-12T23:59:59.000Z

    An acceleration-sensing apparatus is disclosed which includes a moveable shuttle (i.e. a suspended mass) and a latch for capturing and holding the shuttle when an acceleration event is sensed above a predetermined threshold level. The acceleration-sensing apparatus provides a switch closure upon sensing the acceleration event and remains latched in place thereafter. Examples of the acceleration-sensing apparatus are provided which are responsive to an acceleration component in a single direction (i.e. a single-sided device) or to two oppositely-directed acceleration components (i.e. a dual-sided device). A two-stage acceleration-sensing apparatus is also disclosed which can sense two acceleration events separated in time. The acceleration-sensing apparatus of the present invention has applications, for example, in an automotive airbag deployment system.

  20. Real-time Lighting System for Large Group Interaction Joshua Randall

    E-Print Network [OSTI]

    Real-time Lighting System for Large Group Interaction Joshua Randall Massachusetts Institute of Technology May 2002 Abstract Lighting systems have historically been controlled by an individual or small group of human operators working together in real-time. Applications for real-time lighting control

  1. Group classification of systems of non-linear reaction-diffusion equations with general diffusion matrix. II. Generalized Turing systems

    E-Print Network [OSTI]

    A. G. Nikitin

    2007-07-20T23:59:59.000Z

    Group classification of systems of two coupled nonlinear reaction-diffusion equation with a diagonal diffusion matrix is carried out. Symmetries of diffusion systems with singular diffusion matrix and additional first order derivative terms are described.

  2. OSU Building and Environmental Thermal Systems Research Group Citation Index

    E-Print Network [OSTI]

    countries. Renewable and Sustainable Energy Reviews 13(6-7):1383- 1394. Li, S., W. Yang, and X. Zhang. 2009-borehole ground-coupled heat pumps: A review of models and systems. Applied Energy 87(1):16-27. Fabrizio, E., M., and S. Wang 2009. Building energy research in Hong Kong: A review. Renewable and Sustainable Energy

  3. Architecture, implementation, and testing of a multiple-shell gas injection system for high current implosions on the Z accelerator

    SciTech Connect (OSTI)

    Krishnan, Mahadevan; Elliott, Kristi Wilson; Madden, Robert E. [Alameda Applied Sciences Corporation, San Leandro, California 94577 (United States); Coleman, P. L. [Evergreen Hill Sciences, Philomath, Oregon 97370 (United States); Thompson, John R. [812 Temple Street, San Diego, California 92106 (United States); Bixler, Alex [Space Sciences Laboratory, University of California, Berkeley, Berkeley, California 94720 (United States); Lamppa, D. C.; McKenney, J. L.; Strizic, T.; Johnson, D.; Johns, O.; Vigil, M. P.; Jones, B.; Ampleford, D. J.; Savage, M. E.; Cuneo, M. E.; Jones, M. C. [Sandia National Laboratories, Albuquerque, New Mexico 87185 (United States)

    2013-06-15T23:59:59.000Z

    Tests are ongoing to conduct {approx}20 MA z-pinch implosions on the Z accelerator at Sandia National Laboratory using Ar, Kr, and D{sub 2} gas puffs as the imploding loads. The relatively high cost of operations on a machine of this scale imposes stringent requirements on the functionality, reliability, and safety of gas puff hardware. Here we describe the development of a prototype gas puff system including the multiple-shell nozzles, electromagnetic drivers for each nozzle's valve, a UV pre-ionizer, and an inductive isolator to isolate the {approx}2.4 MV machine voltage pulse present at the gas load from the necessary electrical and fluid connections made to the puff system from outside the Z vacuum chamber. This paper shows how the assembly couples to the overall Z system and presents data taken to validate the functionality of the overall system.

  4. High-value use of weapons-plutonium by burning in molten salt accelerator-driven subcritical systems or reactors

    SciTech Connect (OSTI)

    Bowman, C.D.; Venneri, F.

    1993-11-01T23:59:59.000Z

    The application of thermal-spectrum molten-salt reactors and accelerator-driven subcritical systems to the destruction of weapons-return plutonium is considered from the perspective of deriving the maximum societal benefit. The enhancement of electric power production from burning the fertile fuel {sup 232}Th with the plutonium is evaluated. Also the enhancement of destruction of the accumulated waste from commercial nuclear reactors is considered using the neutron-rich weapons plutonium. Most cases examined include the concurrent transmutation of the long-lived actinide and fission product waste ({sup 99}Tc, {sup 129}I, {sup 135}Cs, {sup 126}Sn and {sup 79}Se).

  5. Simulations of flame acceleration and deflagration-to-detonation transitions in methane-air systems

    SciTech Connect (OSTI)

    Kessler, D.A.; Gamezo, V.N.; Oran, E.S. [Laboratory for Computational Physics and Fluid Dynamics, Naval Research Laboratory, Washington, DC (United States)

    2010-11-15T23:59:59.000Z

    Flame acceleration and deflagration-to-detonation transitions (DDT) in large obstructed channels filled with a stoichiometric methane-air mixture are simulated using a single-step reaction mechanism. The reaction parameters are calibrated using known velocities and length scales of laminar flames and detonations. Calculations of the flame dynamics and DDT in channels with obstacles are compared to previously reported experimental data. The results obtained using the simple reaction model qualitatively, and in many cases, quantitatively match the experiments and are found to be largely insensitive to small variations in model parameters. (author)

  6. Comparative Microbial Genomics group CenterforBiologicalSequenceanalysisDepartmentofSystemsBiology,TechnicalUniversityofDenmark

    E-Print Network [OSTI]

    Ussery, David W.

    Comparative Microbial Genomics group CenterforBiologicalSequenceanalysisDepartmentofSystemsBiology,TechnicalUniversityofDenmark E. coli pangenomics - or - How to compare hundreds of E. coli genomes Fuzzy Dave Ussery Ullevål Universitetssykehus Oslo, Norway Wednesday, 10 December, 2008 #12;Comparative Microbial Genomics group Centerfor

  7. Iterative Spatial Sequence Estimator for Multi-Group Space Time Trellis Coded Systems

    E-Print Network [OSTI]

    Al-Ghadhban, Samir

    Iterative Spatial Sequence Estimator for Multi-Group Space Time Trellis Coded Systems Samir Al. The developed detector is called maximum a posteriori spatial sequence estimator and it has the flexibility. A novel spatial sequence estimator (SSE) for V-BLAST is proposed in [4]. The algorithm combines group

  8. Comparison of reliability performance of group connected and conventional HVDC transmission systems

    SciTech Connect (OSTI)

    Kuruganty, S. [Univ. of North Dakota, Grand Forks, ND (United States). Dept. of Electrical Engineering] [Univ. of North Dakota, Grand Forks, ND (United States). Dept. of Electrical Engineering

    1995-10-01T23:59:59.000Z

    A group connected HVDC transmission scheme is a variant of the unit connection where instead of a single generator, a group of generators are directly connected to the converter. Studies conducted in the past indicated that significant cost reduction can be achieved using this scheme. This is mainly due to the elimination of many components which results in considerable capital and operating cost savings to the utility. Concerns regarding the reliability performance of unit connected schemes were raised, however, there has not been a detailed reliability study conducted. This paper addresses the reliability evaluation aspect of a group connected scheme and compares the reliability performance of the group connected scheme with that of the conventional common collector system. Reliability models for both schemes were developed using a hypothetical system model based on the Nelson River system. Practical system component outage data was used to examine the reliability performance of both schemes.

  9. Michael Beetz, Lorenz Mosenlechner, Moritz Tenorth, Thomas Ruhr Intelligent Autonomous Systems Group, Technische Universitat Munchen

    E-Print Network [OSTI]

    Michael Beetz, Lorenz M¨osenlechner, Moritz Tenorth, Thomas R¨uhr Intelligent Autonomous Systems Group, Technische Universit¨at M¨unchen {beetz,moesenle,tenorth,ruehr}@cs.tum.edu CRAM ­ a Cognitive

  10. Progress on laser plasma accelerators

    SciTech Connect (OSTI)

    Chen, P.

    1986-04-01T23:59:59.000Z

    Several laser plasma accelerator schemes are reviewed, with emphasis on the Plasma Beat Wave Accelerator (PBWA). Theory indicates that a very high acceleration gradient, of order 1 GeV/m, can exist in the plasma wave driven by the beating lasers. Experimental results obtained on the PBWA experiment at UCLA confirms this. Parameters related to the PBWA as an accelerator system are derived, among them issues concerning the efficiency and the laser power and energy requirements are discussed.

  11. YALINA facility a sub-critical Accelerator- Driven System (ADS) for nuclear energy research facility description and an overview of the research program (1997-2008).

    SciTech Connect (OSTI)

    Gohar, Y.; Smith, D. L.; Nuclear Engineering Division

    2010-04-28T23:59:59.000Z

    The YALINA facility is a zero-power, sub-critical assembly driven by a conventional neutron generator. It was conceived, constructed, and put into operation at the Radiation Physics and Chemistry Problems Institute of the National Academy of Sciences of Belarus located in Minsk-Sosny, Belarus. This facility was conceived for the purpose of investigating the static and dynamic neutronics properties of accelerator driven sub-critical systems, and to serve as a neutron source for investigating the properties of nuclear reactions, in particular transmutation reactions involving minor-actinide nuclei. This report provides a detailed description of this facility and documents the progress of research carried out there during a period of approximately a decade since the facility was conceived and built until the end of 2008. During its history of development and operation to date (1997-2008), the YALINA facility has hosted several foreign groups that worked with the resident staff as collaborators. The participation of Argonne National Laboratory in the YALINA research programs commenced in 2005. For obvious reasons, special emphasis is placed in this report on the work at YALINA facility that has involved Argonne's participation. Attention is given here to the experimental program at YALINA facility as well as to analytical investigations aimed at validating codes and computational procedures and at providing a better understanding of the physics and operational behavior of the YALINA facility in particular, and ADS systems in general, during the period 1997-2008.

  12. Development of a Rating System for a Comparative Accelerated Test Standard (Presentation)

    SciTech Connect (OSTI)

    Kurtz, S.

    2013-06-01T23:59:59.000Z

    This presentation discusses methods of developing and structuring a useful rating system and communicating the results.

  13. EXTENSIONS OF LINKING SYSTEMS WITH p-GROUP KERNEL BOB OLIVER AND JOANA VENTURA

    E-Print Network [OSTI]

    Ventura, Joana

    EXTENSIONS OF LINKING SYSTEMS WITH p-GROUP KERNEL BOB OLIVER AND JOANA VENTURA Abstract. We study. Oliver is partially supported by UMR 7539 of the CNRS. J. Ventura is partially supported by FCT. #12;2 BOB OLIVER AND JOANA VENTURA enother prolem is tht in generlD when ev is linking system nd A g

  14. THEORY OF DYNAMICAL SYSTEMS AND GENERAL TRANSFORMATION GROUPS WITH INVARIANT MEASURE

    E-Print Network [OSTI]

    Katok, Svetlana

    THEORY OF DYNAMICAL SYSTEMS AND GENERAL TRANSFORMATION GROUPS WITH INVARIANT MEASURE A. B. Katok, Ya. G. Sinai, and A. M. Stepin UDC 513.83:513.88+517.9+519.4 INTRODUCTION The theory of dynamical systems with invariant measure, or ergodic theory, is one of those domains of mathematics whose form

  15. Passivity Index for Switched System Technical Report of the ISIS Group

    E-Print Network [OSTI]

    Antsaklis, Panos

    Passivity Index for Switched System Design Technical Report of the ISIS Group at the University of Notre Dame ISIS-09-002 May, 2009 Michael J. McCourt and Panos J. Antsaklis Department of Electrical.J. McCourt and P.J. Antsaklis, "Passivity Index for Switched System Design," ISIS Technical Report

  16. Signals & Systems Group: NUIM/SS/2002/01 A result on common quadratic Lyapunov

    E-Print Network [OSTI]

    Williamson, John

    Signals & Systems Group: NUIM/SS/2002/01 A result on common quadratic Lyapunov functions R. Shorten, K. Narendra and O. Mason #12;A result on common quadratic Lyapunov functions Robert Shorten Hamilton quadratic Lyapunov functions (CQLF's) for sets of linear time-invariant (LTI) systems. We show

  17. System for Nuclear Waste Transmutation Driven by Target-Distributed Accelerators

    E-Print Network [OSTI]

    Blanovsky, A

    2004-01-01T23:59:59.000Z

    A design concept and characteristics for an epithermal breeder controlled by variable feedback and external neutron source intensity are presented. By replacing the control rods with neutron sources, we could improve safety and perform radioactive waste burning in high flux subcritical reactors (HFSR). To increase neutron source intensity the HFSR is divided into two zones: a booster and a blanket operating with solid and liquid fuels. Use of a liquid actinide fuel permits transport of the delayed-neutron emitters from the blanket to the booster where they can provide additional neutrons or all the necessary excitation. With blanket and booster multiplication factors of k=0.95 and 0.98, respectively, an external photoneutron source rate of at least 10.sup.15 n/s (electron beam power 2.5MW) is needed to control the HFSR that produces 300MWt. An inexpensive method of obtaining large neutron fluxes is target-distributed accelerators (TDA), in which a fission electrical cell (FEC) compensates for lost beam energy...

  18. Design, construction and operational results of the IGBT controlled solid state modulator high voltage power supply used in the high power RF systems of the Low Energy Demonstration Accelerator of the accelerator production of tritium (APT) project

    SciTech Connect (OSTI)

    Bradley, J.T. III; Rees, D.; Przeklasa, R.S. [Los Alamos National Lab., NM (United States); Scott, M.C. [Continental Electronics Corp., Dallas, TX (United States)

    1998-12-31T23:59:59.000Z

    The 1700 MeV, 100 mA Accelerator Production of Tritium (APT) Proton Linac will require 244 1 MW, continuous wave RF systems. 1 MW continuous wave klystrons are used as the RF source and each klystron requires 95 kV, 17 A of beam voltage and current. The cost of the DC power supplies is the single largest percentage of the total RF system cost. Power supply reliability is crucial to overall RF system availability and AC to DC conversion efficiency affects the operating cost. The Low Energy Demonstration Accelerator (LEDA) being constructed at Los Alamos National Laboratory (LANL) will serve as the prototype and test bed for APT. The design of the RF systems used in LEDA is driven by the need to field test high efficiency systems with extremely high reliability before APT is built. The authors present a detailed description and test results of one type of advanced high voltage power supply system using Insulated Gate Bipolar Transistors (IGBTs) that has been used with the LEDA High Power RF systems. The authors also present some of the distinctive features offered by this power supply topology, including crowbarless tube protection and modular construction which allows graceful degradation of power supply operation.

  19. OPERATING EXPERIENCE WITH A NEW ACCELERATOR CONTROL SYSTEM BASED UPON MICROPROCESSORS

    E-Print Network [OSTI]

    Magyary, S.

    2010-01-01T23:59:59.000Z

    CONTROL SYSTEM BASED UPON MICROPROCESSORS* E S. Magyary, H.architecture of i t s microprocessor based control systemlarge number (~20) of microprocessor boards, each executiny

  20. Cryogenic systems for the HEB accelerator of the Superconducting Super Collider

    SciTech Connect (OSTI)

    Abramovich, S.; Yuecel, A.

    1994-07-01T23:59:59.000Z

    This report discusses the following topics related to the Superconducting Super Collider: Cryogenic system -- general requirements; cryogenic system components; heat load budgets and refrigeration plant capacities; flow and thermal characteristics; process descriptions; cryogenic control instrumentation and value engineering trade-offs.

  1. Reduction of the Radiotoxicity of Spent Nuclear Fuel Using a Two-Tiered System Comprising Light Water Reactors and Accelerator-Driven Systems

    SciTech Connect (OSTI)

    H.R. Trellue

    2003-06-01T23:59:59.000Z

    Two main issues regarding the disposal of spent nuclear fuel from nuclear reactors in the United States in the geological repository Yucca Mountain are: (1) Yucca Mountain is not designed to hold the amount of fuel that has been and is proposed to be generated in the next few decades, and (2) the radiotoxicity (i.e., biological hazard) of the waste (particularly the actinides) does not decrease below that of natural uranium ore for hundreds of thousands of years. One solution to these problems may be to use transmutation to convert the nuclides in spent nuclear fuel to ones with shorter half-lives. Both reactor and accelerator-based systems have been examined in the past for transmutation; there are advantages and disadvantages associated with each. By using existing Light Water Reactors (LWRs) to burn a majority of the plutonium in spent nuclear fuel and Accelerator-Driven Systems (ADSs) to transmute the remainder of the actinides, the benefits of each type of system can be realized. The transmutation process then becomes more efficient and less expensive. This research searched for the best combination of LWRs with multiple recycling of plutonium and ADSs to transmute spent nuclear fuel from past and projected nuclear activities (assuming little growth of nuclear energy). The neutronic design of each system is examined in detail although thermal hydraulic performance would have to be considered before a final system is designed. The results are obtained using the Monte Carlo burnup code Monteburns, which has been successfully benchmarked for MOX fuel irradiation and compared to other codes for ADS calculations. The best combination of systems found in this research includes 41 LWRs burning mixed oxide fuel with two recycles of plutonium ({approx}40 years operation each) and 53 ADSs to transmute the remainder of the actinides from spent nuclear fuel over the course of 60 years of operation.

  2. The design and performance of a water cooling system for a prototype coupled cavity linear particle accelerator for the spallation neutron source

    SciTech Connect (OSTI)

    Bernardin, J. D. (John D.); Ammerman, C. N. (Curtt N.); Hopkins, S. M. (Steve M.)

    2002-01-01T23:59:59.000Z

    The Spallation Neutron Source (SNS) is a facility being designed for scientific and industrial research and development. The SNS will generate and employ neutrons as a research tool in a variety of disciplines including biology, material science, superconductivity, chemistry, etc. The neutrons will be produced by bombarding a heavy metal target with a high-energy beam of protons, generated and accelerated with a linear particle accelerator, or linac. The low energy end of the linac consists of, in part, a multi-cell copper structure termed a coupled cavity linac (CCL). The CCL is responsible for accelerating the protons from an energy of 87 MeV, to 185 MeV. Acceleration of the charged protons is achieved by the use of large electrical field gradients established within specially designed contoured cavities of the CCL. While a large amount of the electrical energy is used to accelerate the protons, approximately 60-80% of this electrical energy is dissipated in the CCL's copper structure. To maintain an acceptable operating temperature, as well as minimize thermal stresses and maintain desired contours of the accelerator cavities, the electrical waste heat must be removed from the CCL structure. This is done using specially designed water cooling passages within the linac's copper structure. Cooling water is supplied to these cooling passages by a complex water cooling and temperature control system. This paper discusses the design, analysis, and testing of a water cooling system for a prototype CCL. First, the design concept and method of water temperature control is discussed. Second, the layout of the prototype water cooling system, including the selection of plumbing components, instrumentation, as well as controller hardware and software is presented. Next, the development of a numerical network model used to size the pump, heat exchanger, and plumbing equipment, is discussed. Finally, empirical pressure, flow rate, and temperature data from the prototype CCL water cooling tests are used to assess water cooling system performance and numerical modeling accuracy.

  3. Accelerating value capture of SAP enterprise resource planning (ERP) system : governance model and process

    E-Print Network [OSTI]

    Shih, Ting-Chih

    2009-01-01T23:59:59.000Z

    Raytheon produces a diverse range of defense products using a wide range of business systems and tools that are not currently integrated. To achieve the corporate vision of "one company", in 2005, Raytheon began to deploy ...

  4. OPERATING EXPERIENCE WITH A NEW ACCELERATOR CONTROL SYSTEM BASED UPON MICROPROCESSORS

    E-Print Network [OSTI]

    Magyary, S.

    2010-01-01T23:59:59.000Z

    control system compo­ nents such as multiplexors, timing modules, and graphicsCONTROL " ~ FROM DMM VECTOR VOLTAGES il l ENABLE SCOPE 1 HP 1350A GRAPHICScontrol. These signals are added to the output of the graphics

  5. Experimental study on the thorium-loaded accelerator-driven system at the Kyoto Univ. critical assembly

    SciTech Connect (OSTI)

    Pyeon, C. H.; Yagi, T.; Lim, J. Y.; Misawa, T. [Nuclear Science Engineering Div., Research Reactor Inst., Kyoto Univ., Asashiro-nishi, Kumatori-cho, Sennan-gun, Osaka 590-0494 (Japan)

    2012-07-01T23:59:59.000Z

    The experimental study on the thorium-loaded accelerator-driven system (ADS) is conducted in the Kyoto Univ. Critical Assembly (KUCA). The experiments are carried out in both the critical and subcritical states for attaining the reaction rates of the thorium capture and fission reactions. In the critical system, the thorium plate irradiation experiment is carried out for the thorium capture and fission reactions. From the results of the measurements, the thorium fission reactions are obtained apparently in the critical system, and the C/E values of reaction rates show the accuracy of relative difference of about 30%. In the ADS experiments with 14 MeV neutrons and 100 MeV protons, the subcritical experiments are carried out in the thorium-loaded cores to obtain the capture reaction rates through the measurements of {sup 115}In(n, {gamma}){sup 116m}In reactions. The results of the experiments reveal the difference between the reaction rate distributions for the change in not only the neutron spectrum but also the external neutron source. The comparison between the measured and calculated reaction rate distributions demonstrates a discrepancy of the accuracy of reaction rate analyses of thorium capture reactions through the thorium-loaded ADS experiments with 14 MeV neutrons. Hereafter, kinetic experiments are planned to be carried out to deduce the delayed neutron decay constants and subcriticality using the pulsed neutron method. (authors)

  6. Vehicle Technologies Office Merit Review 2014: Accelerating the Evaluation and Market Introduction of Advanced Technologies Through Model Based System Engineering

    Broader source: Energy.gov [DOE]

    Presentation given by Argonne National Laboratory at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about accelerating the...

  7. Vehicle Technologies Office Merit Review 2015: Accelerate the Development and Introduction of Advanced Technologies Through Model Based System Engineering

    Broader source: Energy.gov [DOE]

    Presentation given by Argonne National Laboratory at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about accelerate the...

  8. Accelerate Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Accelerate Energy Productivity 2030 Over the next year, the U.S. Department of Energy, the Council on Competitiveness and the Alliance to Save Energy will join forces to undertake...

  9. Thermo-Fluids, Energy Systems and Environment This group conducts research in the following areas

    E-Print Network [OSTI]

    Calgary, University of

    and Reacting Flows l Aerodynamics l Internal-Combustion Engines l Stirling Engines l Computational Fluid internal-combustion engines l Cross-flow and co-flow combustion facilities l Flammability test apparatus l-Fluids, Energy Systems and Environment This group conducts research in the following areas: l Combustion

  10. Hydrogen Storage Systems Analysis Working Group Meeting 2007 Hydrogen Program Annual Review

    E-Print Network [OSTI]

    applications. The IPHE (International Partnership for the Hydrogen Economy) safety program to assess storageHydrogen Storage Systems Analysis Working Group Meeting 2007 Hydrogen Program Annual Review Crystal Laboratory and Elvin Yuzugullu Sentech, Inc. June 28, 2007 #12;SUMMARY REPORT Hydrogen Storage

  11. Hydrogen Storage Systems Analysis Working Group Meeting Argonne National Laboratory DC Offices

    E-Print Network [OSTI]

    at Savannah River National Laboratory (Don Anton and Bruce Hardy, SRNL) Based on the operating conditionsHydrogen Storage Systems Analysis Working Group Meeting Argonne National Laboratory DC Offices 955 by Romesh Kumar Argonne National Laboratory and Laura Verduzco Sentech, Inc. February 28, 2007 #12;SUMMARY

  12. Comparative Microbial Genomics group CenterforBiologicalSequenceanalysisDepartmentofSystemsBiology,TechnicalUniversityofDenmark

    E-Print Network [OSTI]

    Ussery, David W.

    Comparative Microbial Genomics group CenterforBiologicalSequenceanalysisDepartmentofSystemsBiology,TechnicalUniversityofDenmark Burkholderia Pan-genomics Dave Ussery Max Planck Institut fur Terrestrial Microbiology Marburg, Germany 26 May, 2008 - or - What can we learn from more than 50 sequenced genomes? #12;Comparative Microbial Genomics

  13. Optimal Well-Group Distribution of a Groundwater Source Heat Pump System

    E-Print Network [OSTI]

    Liu, Z.; Lu, L.; Yoshida, H.

    2006-01-01T23:59:59.000Z

    It is critical to determine how the well group arranges for application of the GWSHP system. Based on the fact that water movement is the most important factor influencing heat transfer in an aquifer, this paper presents a two-step analysis method...

  14. The Well-Group Distribution of Groundwater Source Heat Pump System Optimized Research

    E-Print Network [OSTI]

    Liu, Z.; Lu, L.; Yoshida, H.

    2006-01-01T23:59:59.000Z

    It is the key question that how does the well group arrange for application of GWSHP system. Based on the fact that the water movement is the important factor of heat transfer on aquifer, this paper presents two steps analysis method and analyze...

  15. Optimal Well-Group Distribution of a Groundwater Source Heat Pump System 

    E-Print Network [OSTI]

    Liu, Z.; Lu, L.; Yoshida, H.

    2006-01-01T23:59:59.000Z

    It is critical to determine how the well group arranges for application of the GWSHP system. Based on the fact that water movement is the most important factor influencing heat transfer in an aquifer, this paper presents a two-step analysis method...

  16. The Well-Group Distribution of Groundwater Source Heat Pump System Optimized Research 

    E-Print Network [OSTI]

    Liu, Z.; Lu, L.; Yoshida, H.

    2006-01-01T23:59:59.000Z

    It is the key question that how does the well group arrange for application of GWSHP system. Based on the fact that the water movement is the important factor of heat transfer on aquifer, this paper presents two steps analysis method and analyze...

  17. EXTENSIONS OF LINKING SYSTEMS WITH p-GROUP KERNEL BOB OLIVER AND JOANA VENTURA

    E-Print Network [OSTI]

    Oliver, Bob

    AND JOANA VENTURA Abstract. We study extensions of p-local finite groups where the kernel i* *s of the CNRS. J. Ventura is partially supported by FCT/POCTI/FEDER and grant PDCT/MAT/58497* */2004. Both;2 BOB OLIVER AND JOANA VENTURA Another problem is that in general, when eLis a linking system and A C e

  18. Muon Acceleration - RLA and FFAG

    SciTech Connect (OSTI)

    Alex Bogacz

    2011-10-01T23:59:59.000Z

    Various acceleration schemes for muons are presented. The overall goal of the acceleration systems: large acceptance acceleration to 25 GeV and 'beam shaping' can be accomplished by various fixed field accelerators at different stages. They involve three superconducting linacs: a single pass linear Pre-accelerator followed by a pair of multi-pass Recirculating Linear Accelerators (RLA) and finally a non-scaling FFAG ring. The present baseline acceleration scenario has been optimized to take maximum advantage of appropriate acceleration scheme at a given stage. The solenoid based Pre-accelerator offers very large acceptance and facilitates correction of energy gain across the bunch and significant longitudinal compression trough induced synchrotron motion. However, far off-crest acceleration reduces the effective acceleration gradient and adds complexity through the requirement of individual RF phase control for each cavity. The RLAs offer very efficient usage of high gradient superconducting RF and ability to adjust path-length after each linac pass through individual return arcs with uniformly periodic FODO optics suitable for chromatic compensation of emittance dilution with sextupoles. However, they require spreaders/recombiners switchyards at both linac ends and significant total length of the arcs. The non-scaling Fixed Field Alternating Gradient (FFAG) ring combines compactness with very large chromatic acceptance (twice the injection energy) and it allows for large number of passes through the RF (at least eight, possibly as high as 15).

  19. The Bioinformatics & Systems Biology group (http://bioinformatics.psb.ugent.be/) at the VIB Department of Plant

    E-Print Network [OSTI]

    Gent, Universiteit

    The Bioinformatics & Systems Biology group (http://bioinformatics.psb.ugent.be/) at the VIB in the computational systems biology research group, you will be responsible for the commercialization of our software and food companies to present our in-house systems biology software tools. Profile: · PhD in computational

  20. Acceleration Fund

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office511041cloth DocumentationProducts (VAP) VAP7-0973 1 Introduction In theACME - AcceleratedAccelerating

  1. Five-Year Results From a Scandinavian Sarcoma Group Study (SSG XIII) of Adjuvant Chemotherapy Combined With Accelerated Radiotherapy in High-Risk Soft Tissue Sarcoma of Extremities and Trunk Wall

    SciTech Connect (OSTI)

    Jebsen, Nina L. [Department of Surgical Sciences, University of Bergen Faculty of Medicine, Bergen, Norway and Department of Oncology, Haukeland University Hospital, Bergen (Norway); Bruland, Oyvind S. [Cancer Clinic, Norwegian Radium Hospital, Oslo University Hospital and University of Oslo Faculty Division, Clinical Medicine, Oslo (Norway); Eriksson, Mikael; Engellau, Jacob [Department of Oncology, Skane University Hospital, Lund (Sweden); Turesson, Ingela [Department of Oncology, Uppsala University Hospital, Uppsala (Sweden); Folin, Annika [Department of Oncology, Karolinska Hospital, Stockholm (Sweden); Trovik, Clement S. [Departments of Oncology and of Orthopedics, Haukeland University Hospital, Bergen (Norway); Hall, Kirsten Sundby [Cancer Clinic, Norwegian Radium Hospital, Oslo University Hospital, Oslo (Norway)

    2011-12-01T23:59:59.000Z

    Purpose: To evaluate adjuvant chemotherapy and interpolated accelerated radiotherapy (RT) for adult patients with high-risk soft tissue sarcoma in the extremities or trunk wall. Methods and Materials: High-risk soft tissue sarcoma was defined as high-grade malignancy and at least two of the following criteria: size {>=}8 cm, vascular invasion, or necrosis. Six cycles of doxorubicin and ifosfamide were prescribed for all patients. RT to a total dose of 36 Gy (1.8 Gy twice daily) was inserted between two chemotherapy cycles after marginal margin resection regardless of tumor depth or after wide-margin resection for deep-seated tumors. RT was boosted to 45 Gy in a split-course design in the case of intralesional margin resection. Results: A total of 119 patients were eligible, with a median follow-up of 5 years. The 5-year estimate of the local recurrence, metastasis-free survival, and overall survival rate was 12%, 59%, and 68%, respectively. The group receiving RT to 36 Gy had a local recurrence rate of 10%. In contrast, the local recurrence rate was 29% in the group treated with RT to 45 Gy. The presence of vascular invasion and low chemotherapy dose intensity had a negative effect on metastasis-free and overall survival. Toxicity was moderate after both the chemotherapy and the RT. Conclusions: Accelerated RT interposed between chemotherapy cycles in a selected population of patients with high-risk soft tissue sarcoma resulted in good local and distant disease control, with acceptable treatment-related morbidity. The greater radiation dose administered after intralesional surgery was not sufficient to compensate for the poorer surgical margin. Vascular invasion was the most important prognostic factor for metastasis-free and overall survival.

  2. Test Facility Daniil Stolyarov, Accelerator Test Facility User...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Development of the Solid-State Laser System for the Accelerator Test Facility Daniil Stolyarov, Accelerator Test Facility User's Meeting April 3, 2009 Outline Motivation for...

  3. Plasma accelerator

    DOE Patents [OSTI]

    Wang, Zhehui (Los Alamos, NM); Barnes, Cris W. (Santa Fe, NM)

    2002-01-01T23:59:59.000Z

    There has been invented an apparatus for acceleration of a plasma having coaxially positioned, constant diameter, cylindrical electrodes which are modified to converge (for a positive polarity inner electrode and a negatively charged outer electrode) at the plasma output end of the annulus between the electrodes to achieve improved particle flux per unit of power.

  4. Thomas Precession by Uniform Acceleration

    E-Print Network [OSTI]

    Miroslav Pardy

    2014-12-09T23:59:59.000Z

    We determine the nonlinear transformations between coordinate systems which are mutually in a constant symmetrical accelerated motion. The maximal acceleration limit follows from the kinematical origin and it is an analogue of the maximal velocity in special relativity. We derive the dependence of mass, length, time, Doppler effect, Cherenkov effect and transition radiation angle on acceleration as an analogue phenomena in special theory of relativity. The last application of our method is the Thomas precession by uniform acceleration with the possible role in the modern physics and cosmology. The comparison of derived results with other relativistic methods is necessary.

  5. Compact accelerator for medical therapy

    DOE Patents [OSTI]

    Caporaso, George J.; Chen, Yu-Jiuan; Hawkins, Steven A.; Sampayan, Stephen E.; Paul, Arthur C.

    2010-05-04T23:59:59.000Z

    A compact accelerator system having an integrated particle generator-linear accelerator with a compact, small-scale construction capable of producing an energetic (.about.70-250 MeV) proton beam or other nuclei and transporting the beam direction to a medical therapy patient without the need for bending magnets or other hardware often required for remote beam transport. The integrated particle generator-accelerator is actuable as a unitary body on a support structure to enable scanning of a particle beam by direction actuation of the particle generator-accelerator.

  6. Thomas Precession by Uniform Acceleration

    E-Print Network [OSTI]

    Pardy, Miroslav

    2015-01-01T23:59:59.000Z

    We determine the nonlinear transformations between coordinate systems which are mutually in a constant symmetrical accelerated motion. The maximal acceleration limit follows from the kinematical origin and it is an analogue of the maximal velocity in special relativity. We derive the dependence of mass, length, time, Doppler effect, Cherenkov effect and transition radiation angle on acceleration as an analogue phenomena in special theory of relativity. The last application of our method is the Thomas precession by uniform acceleration with the possible role in the modern physics and cosmology. The comparison of derived results with other relativistic methods is necessary.

  7. Entanglement renormalization in free bosonic systems: real-space versus momentum-space renormalization group transforms

    E-Print Network [OSTI]

    G. Evenbly; G. Vidal

    2010-03-05T23:59:59.000Z

    The ability of entanglement renormalization (ER) to generate a proper real-space renormalization group (RG) flow in extended quantum systems is analysed in the setting of harmonic lattice systems in D=1 and D=2 spatial dimensions. A conceptual overview of the steps involved in momentum-space RG is provided and contrasted against the equivalent steps in the real-space setting. The real-space RG flow, as generated by ER, is compared against the exact results from momentum-space RG, including an investigation of a critical fixed point and the effect of relevant and irrelevant perturbations.

  8. MUON ACCELERATION

    SciTech Connect (OSTI)

    BERG,S.J.

    2003-11-18T23:59:59.000Z

    One of the major motivations driving recent interest in FFAGs is their use for the cost-effective acceleration of muons. This paper summarizes the progress in this area that was achieved leading up to and at the FFAG workshop at KEK from July 7-12, 2003. Much of the relevant background and references are also given here, to give a context to the progress we have made.

  9. Acceleration of dormant storage effects to address the reliability of silicon surface micromachined Micro-Electro-Mechanical Systems (MEMS).

    SciTech Connect (OSTI)

    Cox, James V.; Candelaria, Sam A.; Dugger, Michael Thomas; Duesterhaus, Michelle Ann; Tanner, Danelle Mary; Timpe, Shannon J.; Ohlhausen, James Anthony; Skousen, Troy J.; Jenkins, Mark W.; Jokiel, Bernhard, Jr.; Walraven, Jeremy Allen; Parson, Ted Blair

    2006-06-01T23:59:59.000Z

    Qualification of microsystems for weapon applications is critically dependent on our ability to build confidence in their performance, by predicting the evolution of their behavior over time in the stockpile. The objective of this work was to accelerate aging mechanisms operative in surface micromachined silicon microelectromechanical systems (MEMS) with contacting surfaces that are stored for many years prior to use, to determine the effects of aging on reliability, and relate those effects to changes in the behavior of interfaces. Hence the main focus was on 'dormant' storage effects on the reliability of devices having mechanical contacts, the first time they must move. A large number ({approx}1000) of modules containing prototype devices and diagnostic structures were packaged using the best available processes for simple electromechanical devices. The packaging processes evolved during the project to better protect surfaces from exposure to contaminants and water vapor. Packages were subjected to accelerated aging and stress tests to explore dormancy and operational environment effects on reliability and performance. Functional tests and quantitative measurements of adhesion and friction demonstrated that the main failure mechanism during dormant storage is change in adhesion and friction, precipitated by loss of the fluorinated monolayer applied after fabrication. The data indicate that damage to the monolayer can occur at water vapor concentrations as low as 500 ppm inside the package. The most common type of failure was attributed to surfaces that were in direct contact during aging. The application of quantitative methods for monolayer lubricant analysis showed that even though the coverage of vapor-deposited monolayers is generally very uniform, even on hidden surfaces, locations of intimate contact can be significantly depleted in initial concentration of lubricating molecules. These areas represent defects in the film prone to adsorption of water or contaminants that can cause movable structures to adhere. These analysis methods also indicated significant variability in the coverage of lubricating molecules from one coating process to another, even for identical processing conditions. The variability was due to residual molecules left in the deposition chamber after incomplete cleaning. The coating process was modified to result in improved uniformity and total coverage. Still, a direct correlation was found between the resulting static friction behavior of MEMS interfaces, and the absolute monolayer coverage. While experimental results indicated that many devices would fail to start after aging, the modeling approach used here predicted that all the devices should start. Adhesion modeling based upon values of adhesion energy from cantilever beams is therefore inadequate. Material deposition that bridged gaps was observed in some devices, and potentially inhibits start-up more than the adhesion model indicates. Advances were made in our ability to model MEMS devices, but additional combined experimental-modeling studies will be needed to advance the work to a point of providing predictive capability. The methodology developed here should prove useful in future assessments of device aging, however. Namely, it consisted of measuring interface properties, determining how they change with time, developing a model of device behavior incorporating interface behavior, and then using the age-aware interface behavior model to predict device function.

  10. Accelerators and the Accelerator Community

    SciTech Connect (OSTI)

    Malamud, Ernest; Sessler, Andrew

    2008-06-01T23:59:59.000Z

    In this paper, standing back--looking from afar--and adopting a historical perspective, the field of accelerator science is examined. How it grew, what are the forces that made it what it is, where it is now, and what it is likely to be in the future are the subjects explored. Clearly, a great deal of personal opinion is invoked in this process.

  11. Operable Unit 3-13, Group 7, SFE-20 Hot Waste Tank System Remedial Action Request

    SciTech Connect (OSTI)

    L. Davison

    2009-06-30T23:59:59.000Z

    This Remedial Action Report summarizes activities undertaken to remediate the Operable Unit 3-13, Group 7, SFE-20 Hot Waste Tank System at the Idaho Nuclear Technology and Engineering Center at the Idaho National Laboratory Site. The site addressed in this report was defined in the Operable Unit 3-13 Record of Decision and subsequent implementing documents. This report concludes that remediation requirements and cleanup goals established for the site have been accomplished and is hereafter considered a No Further Action site.

  12. Operable Unit 3-13, Group 7, SFE-20 Hot Waste Tank System Remedial Action Report

    SciTech Connect (OSTI)

    Lee Davison

    2009-06-30T23:59:59.000Z

    This Remedial Action Report summarizes activities undertaken to remediate the Operable Unit 3-13, Group 7, SFE-20 Hot Waste Tank System at the Idaho Nuclear Technology and Engineering Center at the Idaho National Laboratory Site. The site addressed in this report was defined in the Operable Unit 3-13 Record of Decision and subsequent implementing documents. This report concludes that remediation requirements and cleanup goals established for the site have been accomplished and is hereafter considered a No Further Action site.

  13. Frequency Interpolation Methods for Accelerating Parallel EMC Analysis Secure Computing Laboratory, Computer System Laboratories, Fujitsu Laboratories Ltd

    E-Print Network [OSTI]

    Strazdins, Peter

    Frequency Interpolation Methods for Accelerating Parallel EMC Analysis K. Homma Secure Computing-specific Electromagnetic Compatibility (EMC) re- quirements. Hence, minimizing the undesired radiation and avoiding electromagnetic wave radiation from these devices tends to increase. In such a situation, the estimation of EMC

  14. Peculiar acceleration

    E-Print Network [OSTI]

    Luca Amendola; Claudia Quercellini; Amedeo Balbi

    2007-08-08T23:59:59.000Z

    It has been proposed recently to observe the change in cosmological redshift of distant galaxies or quasars with the next generation of large telescope and ultra-stable spectrographs (the so-called Sandage-Loeb test). Here we investigate the possibility of observing the change in peculiar velocity in nearby clusters and galaxies. This ``peculiar acceleration'' could help reconstructing the gravitational potential without assuming virialization. We show that the expected effect is of the same order of magnitude of the cosmological velocity shift. Finally, we discuss how to convert the theoretical predictions into quantities directly related to observations.

  15. ACCELERATE ENERGY

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015ofDepartmentDepartment of Energy ThisThistheSummaryACCELERATE ENERGY

  16. Linear Accelerator

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC)Integrated Codes |Is Your HomeLatestCenter (LMI-EFRC) -Choices toLeeLinear Accelerator

  17. AAPM Task Group 128: Quality assurance tests for prostate brachytherapy ultrasound systems

    SciTech Connect (OSTI)

    Pfeiffer, Douglas; Sutlief, Steven; Feng Wenzheng; Pierce, Heather M.; Kofler, Jim [Imaging Department, Boulder Community Foothills Hospital, Boulder, Colorado 80301 (United States); Radiation Therapy, VA Medical Center, VA Puget Sound Health Care System, Seattle, Washingon 98108 (United States); Cardiology and Interventional Radiology, William Beaumont Hospital, Royal Oak, Michigan 48073 (United States); CIRS, Inc., Norfolk, Virginia 23513 (United States); Radiology, Mayo Clinic, Rochester, Minnesota 55905 (United States)

    2008-12-15T23:59:59.000Z

    While ultrasound guided prostate brachytherapy has gained wide acceptance as a primary treatment tool for prostate cancer, quality assurance of the ultrasound guidance system has received very little attention. Task Group 128 of the American Association of Physicists in Medicine was created to address quality assurance requirements specific to transrectal ultrasound used for guidance of prostate brachytherapy. Accurate imaging guidance and dosimetry calculation depend upon the quality and accuracy of the ultrasound image. Therefore, a robust quality assurance program for the ultrasound system is essential. A brief review of prostate brachytherapy and ultrasound physics is provided, followed by a recommendation for elements to be included in a comprehensive test phantom. Specific test recommendations are presented, covering grayscale visibility, depth of penetration, axial and lateral resolution, distance measurement, area measurement, volume measurement, needle template/electronic grid alignment, and geometric consistency with the treatment planning computer.

  18. Linear induction accelerator

    DOE Patents [OSTI]

    Buttram, M.T.; Ginn, J.W.

    1988-06-21T23:59:59.000Z

    A linear induction accelerator includes a plurality of adder cavities arranged in a series and provided in a structure which is evacuated so that a vacuum inductance is provided between each adder cavity and the structure. An energy storage system for the adder cavities includes a pulsed current source and a respective plurality of bipolar converting networks connected thereto. The bipolar high-voltage, high-repetition-rate square pulse train sets and resets the cavities. 4 figs.

  19. University of Hawaii Advisory Task Group -Operational Assessment Report on System Level Administration Operating Policies and Practices

    E-Print Network [OSTI]

    #12;University of Hawaii ­ Advisory Task Group - Operational Assessment Report on System Level") approved the formation of an Advisory Task Group on Operational and Financial Controls Improvement ("ATG of eight members, four members from the BOR, and four from private industry with expertise in financial

  20. Michael Beetz, Moritz Tenorth, Dejan Pangercic, Benjamin Pitzer Intelligent Autonomous Systems Group, Technische Universitat Munchen and Bosch RTC

    E-Print Network [OSTI]

    Michael Beetz, Moritz Tenorth, Dejan Pangercic, Benjamin Pitzer Intelligent Autonomous Systems Group, Technische Universit¨at M¨unchen and Bosch RTC {beetz,tenorth,pangercic}@cs.tum.edu, Benjamin

  1. Sandia National Laboratories: accelerate hydrogen infrastructure...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    accelerate hydrogen infrastructure technologies Energy Department Awards 7M to Advance Hydrogen Storage Systems On June 12, 2014, in CRF, Energy, Energy Storage, Energy Storage...

  2. Sandia National Laboratories: accelerated lifetime testing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    accelerated lifetime testing Sandia Solar Energy Test System Cited in National Engineering Competition On May 16, 2013, in Concentrating Solar Power, Energy, Energy Storage,...

  3. accelerator-driven targets understanding: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The accelerator-driven system (ADS) is recognized Haviland, David 3 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  4. FFAG ACCELERATOR PROTON DRIVER FOR NEUTRINO FACTORY.

    SciTech Connect (OSTI)

    RUGGIERO, A.

    2005-06-21T23:59:59.000Z

    This paper is the summary of a conceptual study of a Proton Driver for Neutrino Factory based on the use of a Fixed-Field Alternating-Gradient (FFAG) Accelerator. The required proton energy range for an optimum neutrino production is 5 to 12 GeV. This can be accomplished with a group of three concentric rings each with 807 m circumference [1]. FFAG Accelerators [2] have the capability to accelerate charged particles over a large momentum range ({+-}30-50%) and the feature of constant bending and focusing fields. Particles can be accelerated very fast at the rate given by the accelerating field of RF cavities placed in proper locations between magnets. The performance of FFAG accelerators is to be placed between that of Super-Conducting Linear Accelerators (SCL), with which they share the fast acceleration rate, and Rapid-Cycling Synchrotrons (RCS), as they allow the beam to re-circulate over fewer revolutions. Brookhaven National Laboratory is involved in the study of feasibility of FFAG Accelerators to accelerate intense beams of protons in the GeV energy range for a variety of applications the most important of which is the Upgrade of the Alternating Gradient Synchrotron (AGS) with a new FFAG injector [3] accelerating from 400 MeV to 1.5 GeV. The ring would be housed in the AGS tunnel and has henceforth a circumference of 807 m.

  5. A Wire Position Monitor System for the 1.3 FHZ Tesla-Style Cryomodule at the Fermilab New-Muon-Lab Accelerator

    SciTech Connect (OSTI)

    Eddy, N.; Fellenz, B.; Prieto, P.; Semenov, A.; Voy, D.C.; Wendt, M.; /Fermilab

    2011-08-17T23:59:59.000Z

    The first cryomodule for the beam test facility at the Fermilab New-Muon-Lab building is currently under RF commissioning. Among other diagnostics systems, the transverse position of the helium gas return pipe with the connected 1.3 GHz SRF accelerating cavities is measured along the {approx}15 m long module using a stretched-wire position monitoring system. An overview of the wire position monitor system technology is given, along with preliminary results taken at the initial module cooldown, and during further testing. As the measurement system offers a high resolution, we also discuss options for use as a vibration detector. An electron beam test facility, based on superconducting RF (SRF) TESLA-style cryomodules is currently under construction at the Fermilab New-Muon-Lab (NML) building. The first, so-called type III+, cryomodule (CM-1), equipped with eight 1.3 GHz nine-cell accelerating cavities was recently cooled down to 2 K, and is currently under RF conditioning. The transverse alignment of the cavity string within the cryomodule is crucial for minimizing transverse kick and beam break-up effects, generated by the high-order dipole modes of misaligned accelerating structures. An optimum alignment can only be guaranteed during the assembly of the cavity string, i.e. at room temperatures. The final position of the cavities after cooldown is uncontrollable, and therefore unknown. A wire position monitoring system (WPM) can help to understand the transverse motion of the cavities during cooldown, their final location and the long term position stability after cryo-temperatures are settled, as well as the position reproducibility for several cold-warm cycles. It also may serve as vibration sensor, as the wire acts as a high-Q resonant detector for mechanical vibrations in the low-audio frequency range. The WPM system consists out of a stretched-wire position detection system, provided with help of INFN-Milano and DESY Hamburg, and RF generation and read-out electronics, developed at Fermilab.

  6. for sequence accelerators

    E-Print Network [OSTI]

    Zakharov, Vladimir

    Wynn's -algorithm for sequence accelerators using high precision arithmetic Rachel Baumann University of Arizona Wynn's -algorithm for sequence accelerators using high precision arithmetic Rachel Baumann University of Arizona April 17, 2012 #12;Wynn's -algorithm for sequence accelerators using high

  7. Accelerator Technology Division progress report, FY 1992

    SciTech Connect (OSTI)

    Schriber, S.O.; Hardekopf, R.A.; Heighway, E.A.

    1993-07-01T23:59:59.000Z

    This report briefly discusses the following topics: The Ground Test Accelerator Program; Defense Free-Electron Lasers; AXY Programs; A Next Generation High-Power Neutron-Scattering Facility; JAERI OMEGA Project and Intense Neutron Sources for Materials Testing; Advanced Free-Electron Laser Initiative; Superconducting Supercollider; The High-Power Microwave (HPM) Program; Neutral Particle Beam (NPB) Power Systems Highlights; Industrial Partnering; Accelerator Physics and Special Projects; Magnetic Optics and Beam Diagnostics; Accelerator Design and Engineering; Radio-Frequency Technology; Accelerator Theory and Free-Electron Laser Technology; Accelerator Controls and Automation; Very High-Power Microwave Sources and Effects; and GTA Installation, Commissioning, and Operations.

  8. Membrane and MEA Accelerated Stress Test Protocols

    Broader source: Energy.gov (indexed) [DOE]

    and MEA Accelerated Stress Test Protocols Presented at High Temperature Membrane Working Group Meeting Washington, DC May 14, 2007 T.G. Benjamin Argonne National Laboratory 2 0 10...

  9. Multiorbit induction accelerators

    SciTech Connect (OSTI)

    Zvontsov, A.A.; Kas'yanov, V.A.; Chakhlov, V.L.

    1985-09-01T23:59:59.000Z

    Large numbers of particles accelerated per cycle are made possible by accelerating simultaneously in several equilibrium orbits in a single betatron structure. (AIP)

  10. The Bioinformatics & Systems Biology group (http://bioinformatics.psb.ugent.be/) at the VIB Department of Plant

    E-Print Network [OSTI]

    Gent, Universiteit

    The Bioinformatics & Systems Biology group (http://bioinformatics.psb.ugent.be/) at the VIB Administrator/Bioinformatician As a member of VIB's a new bioinformatics project framed in the computational Department of Plant Systems Biology studies the structure, function and evolution of biological networks

  11. An Autonomous System for Grouping Events in a Developing Aftershock Sequence

    SciTech Connect (OSTI)

    Harris, D. B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dodge, D. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2011-03-22T23:59:59.000Z

    We describe a prototype detection framework that automatically clusters events in real time from a rapidly unfolding aftershock sequence. We use the fact that many aftershocks are repetitive, producing similar waveforms. By clustering events based on correlation measures of waveform similarity, the number of independent event instances that must be examined in detail by analysts may be reduced. Our system processes array data and acquires waveform templates with a short-term average (STA)/long-term average (LTA) detector operating on a beam directed at the P phases of the aftershock sequence. The templates are used to create correlation-type (subspace) detectors that sweep the subsequent data stream for occurrences of the same waveform pattern. Events are clustered by association with a particular detector. Hundreds of subspace detectors can run in this framework a hundred times faster than in real time. Nonetheless, to check the growth in the number of detectors, the framework pauses periodically and reclusters detections to reduce the number of event groups. These groups define new subspace detectors that replace the older generation of detectors. Because low-magnitude occurrences of a particular signal template may be missed by the STA/LTA detector, we advocate restarting the framework from the beginning of the sequence periodically to reprocess the entire data stream with the existing detectors. We tested the framework on 10 days of data from the Nevada Seismic Array (NVAR) covering the 2003 San Simeon earthquake. One hundred eighty-four automatically generated detectors produced 676 detections resulting in a potential reduction in analyst workload of up to 73%.

  12. Weak-Chaos Ratchet Accelerator

    E-Print Network [OSTI]

    Itzhack Dana; Vladislav B. Roitberg

    2012-05-28T23:59:59.000Z

    Classical Hamiltonian systems with a mixed phase space and some asymmetry may exhibit chaotic ratchet effects. The most significant such effect is a directed momentum current or acceleration. In known model systems, this effect may arise only for sufficiently strong chaos. In this paper, a Hamiltonian ratchet accelerator is introduced, featuring a momentum current for arbitrarily weak chaos. The system is a realistic, generalized kicked rotor and is exactly solvable to some extent, leading to analytical expressions for the momentum current. While this current arises also for relatively strong chaos, the maximal current is shown to occur, at least in one case, precisely in a limit of arbitrarily weak chaos.

  13. Centralized digital control of accelerators

    SciTech Connect (OSTI)

    Melen, R.E.

    1983-09-01T23:59:59.000Z

    In contrasting the title of this paper with a second paper to be presented at this conference entitled Distributed Digital Control of Accelerators, a potential reader might be led to believe that this paper will focus on systems whose computing intelligence is centered in one or more computers in a centralized location. Instead, this paper will describe the architectural evolution of SLAC's computer based accelerator control systems with respect to the distribution of their intelligence. However, the use of the word centralized in the title is appropriate because these systems are based on the use of centralized large and computationally powerful processors that are typically supported by networks of smaller distributed processors.

  14. SLAC National Accelerator Laboratory Accelerator Physics Faculty Search

    E-Print Network [OSTI]

    Ford, James

    SLAC National Accelerator Laboratory Accelerator Physics Faculty Search The SLAC National Accelerator Laboratory invites applications for a faculty appointment in Accelerator Physics (LCLS), LCLS-II, SPEAR-3, NLC Test Accelerator (NLCTA), Cathode Test Facility (CTF), the proposed

  15. Health-hazard evaluation report HETA 87-392-2099, Loral Systems Group, Akron, Ohio

    SciTech Connect (OSTI)

    Not Available

    1991-02-01T23:59:59.000Z

    In response to a request from the International Union, United Automobile, Aerospace and Agricultural Implement Workers of America (UAW), an evaluation was undertaken of possible health hazards at the Loral Systems Group (SIC-3728) located in Akron, Ohio. Concern was voiced about possible asbestos (1332214) exposure. The company produces wheels and brakes for civilian and military aircraft and currently employs about 1560 persons at the Akron facility. At the time of the study there were about 2300 living retirees. The precise number who had worked in one of the four areas of particular interest was unkown. Of the 166 persons found eligible for inclusion in the health hazard evaluation (15 or more years of potential asbestos exposure in at least one of the four identified programs and still residing in Ohio), 129 participated in a medical evaluation consisting of a chest x-ray, pulmonary function test, and completion of a questionnaire to detail medical and prior work histories. Abnormal pulmonary function results were noted in 39 of these individuals of whom 30 demonstrated an obstructive pattern, three a restrictive pattern, and six both an obstructive and restrictive component. Nonsmoking participants were more likely to report chronic cough, chronic phlegm, and chronic bronchitis than comparisons.

  16. Explorations in combining cognitive models of individuals and system dynamics models of groups.

    SciTech Connect (OSTI)

    Backus, George A.

    2008-07-01T23:59:59.000Z

    This report documents a demonstration model of interacting insurgent leadership, military leadership, government leadership, and societal dynamics under a variety of interventions. The primary focus of the work is the portrayal of a token societal model that responds to leadership activities. The model also includes a linkage between leadership and society that implicitly represents the leadership subordinates as they directly interact with the population. The societal model is meant to demonstrate the efficacy and viability of using System Dynamics (SD) methods to simulate populations and that these can then connect to cognitive models depicting individuals. SD models typically focus on average behavior and thus have limited applicability to describe small groups or individuals. On the other hand, cognitive models readily describe individual behavior but can become cumbersome when used to describe populations. Realistic security situations are invariably a mix of individual and population dynamics. Therefore, the ability to tie SD models to cognitive models provides a critical capability that would be otherwise be unavailable.

  17. Accelerators | Photon Science | Particle Physics Deutsches Elektronen-Synchrotron

    E-Print Network [OSTI]

    Accelerators | Photon Science | Particle Physics Deutsches Elektronen-Synchrotron A Research Centre and astroparticle physics as well as accelerator physics. The theoretical astroparticle physics group at DESY has processes Requirements · Ph.D. in physics or astronomy · Experience with modeling of particle acceleration

  18. Superconducting Radiofrequency (SRF) Accelerator Cavities

    ScienceCinema (OSTI)

    Reece, Charlie

    2014-05-22T23:59:59.000Z

    Charlie Reece, an accelerator technology scientist, explains how superconducting radiofrequency accelerator cavities work.

  19. Combustion Group Group members

    E-Print Network [OSTI]

    Wang, Wei

    Combustion Group Group members: Thierry Poinsot, Emilien Courtine, Luc Vervisch, Benjamin Farcy 2014 #12;Combustion Group Combustion Physics and Modeling Pollutants, Emissions, and Soot Formation Thermoacoustics and Combustion Dynamics Research focus § Examine mechanisms responsible for flame stabilization

  20. APT accelerator. Topical report

    SciTech Connect (OSTI)

    Lawrence, G.; Rusthoi, D. [comp.] [ed.

    1995-03-01T23:59:59.000Z

    The Accelerator Production of Tritium (APT) project, sponsored by Department of Energy Defense Programs (DOE/DP), involves the preconceptual design of an accelerator system to produce tritium for the nation`s stockpile of nuclear weapons. Tritium is an isotope of hydrogen used in nuclear weapons, and must be replenished because of radioactive decay (its half-life is approximately 12 years). Because the annual production requirements for tritium has greatly decreased since the end of the Cold War, an alternative approach to reactors for tritium production, based on a linear accelerator, is now being seriously considered. The annual tritium requirement at the time this study was undertaken (1992-1993) was 3/8 that of the 1988 goal, usually stated as 3/8-Goal. Continued reduction in the number of weapons in the stockpile has led to a revised (lower) production requirement today (March, 1995). The production requirement needed to maintain the reduced stockpile, as stated in the recent Nuclear Posture Review (summer 1994) is approximately 3/16-Goal, half the previous level. The Nuclear Posture Review also requires that the production plant be designed to accomodate a production increase (surge) to 3/8-Goal capability within five years, to allow recovery from a possible extended outage of the tritium plant. A multi-laboratory team, collaborating with several industrial partners, has developed a preconceptual APT design for the 3/8-Goal, operating at 75% capacity. The team has presented APT as a promising alternative to the reactor concepts proposed for Complex-21. Given the requirements of a reduced weapons stockpile, APT offers both significant safety, environmental, and production-fexibility advantages in comparison with reactor systems, and the prospect of successful development in time to meet the US defense requirements of the 21st Century.

  1. Information findability : an informal study to explore options for improving information findability for the systems analysis group.

    SciTech Connect (OSTI)

    Stoecker, Nora K.

    2014-03-01T23:59:59.000Z

    A Systems Analysis Group has existed at Sandia National Laboratories since at least the mid-1950s. Much of the group’s work output (reports, briefing documents, and other materials) has been retained, along with large numbers of related documents. Over time the collection has grown to hundreds of thousands of unstructured documents in many formats contained in one or more of several different shared drives or SharePoint sites, with perhaps five percent of the collection still existing in print format. This presents a challenge. How can the group effectively find, manage, and build on information contained somewhere within such a large set of unstructured documents? In response, a project was initiated to identify tools that would be able to meet this challenge. This report documents the results found and recommendations made as of August 2013.

  2. Group 3: Humidity, Temperature, and Voltage (Presentation)

    SciTech Connect (OSTI)

    Wohlgemuth, J.

    2013-05-01T23:59:59.000Z

    Group 3 is chartered to develop accelerated stress tests that can be used as comparative predictors of module lifetime versus stresses associated with humidity, temperature and voltage.

  3. Modelling and Improving Group Communication in Server Operating Systems Michael Kwok, Tim Brecht, Martin Karsten, Jialin Song

    E-Print Network [OSTI]

    Li, Ming

    Modelling and Improving Group Communication in Server Operating Systems Michael Kwok, Tim Brecht implementations use a client-server archi- tecture that requires the server to send the same data to all members data from the server to each recipient in a unicast fashion. The problem with this approach

  4. Meeting of The New York State Sustainability Education Working Group Syracuse Center of Excellence In Environmental and Energy Systems

    E-Print Network [OSTI]

    Linsley, Braddock K.

    In Environmental and Energy Systems 727 East Washington Street Syracuse, New York April 1, 2012 RECOMMENDED ACTIONMeeting of The New York State Sustainability Education Working Group Syracuse Center of Excellence STEPS The Goal: Every graduate of a New York college or university will be literate about how to live

  5. Books of Jeu and the Pistis Sophia: system, practice, and development of a religious group 

    E-Print Network [OSTI]

    Evans, Erin Michelle

    2012-06-26T23:59:59.000Z

    The primary objective of this thesis is to argue that the Books of Jeu (in the Bruce Codex) and the Pistis Sophia (the Askew Codex) are the product of a hitherto largely unrecognized religious group or community emerging ...

  6. Enlarged Transformation Group: Star Models,Dark Matter Halos and Solar System Dynamics

    E-Print Network [OSTI]

    Edward Lee Green

    2014-07-25T23:59:59.000Z

    Previously a theory has been presented which extends the geometrical structure of a real four-dimensional space-time via a field of orthonormal tetrads with an enlarged transformation group. This new transformation group, called the conservation group, contains the group of diffeomorphisms as a proper subgroup and we hypothesize that it is the foundational group for quantum geometry. The fundamental geometric object of the new geometry is the curvature vector, C^\\mu . Using the scalar Lagrangian density C^\\mu C_\\mu \\sqrt{-g}, field equations for the free field have been obtained which are invariant under the conservation group. In this paper, this theory is further extended by development of a suitable Lagrangian for a field with sources. Spherically symmetric solutions for both the free field and the field with sources are given. A stellar model and an external, free-field model are developed. The theory implies that the external stress-energy tensor has non-compact support and hence may give the geometrical foundation for dark matter. The resulting models are compared to the internal and external Schwarzschild models. The theory may explain the Pioneer anomaly and the corona heating problem.

  7. Community Petascale Project for Accelerator Science and Simulation: Advancing Computational Science for Future Accelerators and Accelerator Technologies

    SciTech Connect (OSTI)

    Spentzouris, P.; /Fermilab; Cary, J.; /Tech-X, Boulder; McInnes, L.C.; /Argonne; Mori, W.; /UCLA; Ng, C.; /SLAC; Ng, E.; Ryne, R.; /LBL, Berkeley

    2011-11-14T23:59:59.000Z

    The design and performance optimization of particle accelerators are essential for the success of the DOE scientific program in the next decade. Particle accelerators are very complex systems whose accurate description involves a large number of degrees of freedom and requires the inclusion of many physics processes. Building on the success of the SciDAC-1 Accelerator Science and Technology project, the SciDAC-2 Community Petascale Project for Accelerator Science and Simulation (ComPASS) is developing a comprehensive set of interoperable components for beam dynamics, electromagnetics, electron cooling, and laser/plasma acceleration modelling. ComPASS is providing accelerator scientists the tools required to enable the necessary accelerator simulation paradigm shift from high-fidelity single physics process modeling (covered under SciDAC1) to high-fidelity multiphysics modeling. Our computational frameworks have been used to model the behavior of a large number of accelerators and accelerator R&D experiments, assisting both their design and performance optimization. As parallel computational applications, the ComPASS codes have been shown to make effective use of thousands of processors. ComPASS is in the first year of executing its plan to develop the next-generation HPC accelerator modeling tools. ComPASS aims to develop an integrated simulation environment that will utilize existing and new accelerator physics modules with petascale capabilities, by employing modern computing and solver technologies. The ComPASS vision is to deliver to accelerator scientists a virtual accelerator and virtual prototyping modeling environment, with the necessary multiphysics, multiscale capabilities. The plan for this development includes delivering accelerator modeling applications appropriate for each stage of the ComPASS software evolution. Such applications are already being used to address challenging problems in accelerator design and optimization. The ComPASS organization for software development and applications accounts for the natural domain areas (beam dynamics, electromagnetics, and advanced acceleration), and all areas depend on the enabling technologies activities, such as solvers and component technology, to deliver the desired performance and integrated simulation environment. The ComPASS applications focus on computationally challenging problems important for design or performance optimization to all major HEP, NP, and BES accelerator facilities. With the cost and complexity of particle accelerators rising, the use of computation to optimize their designs and find improved operating regimes becomes essential, potentially leading to significant cost savings with modest investment.

  8. SLAC National Accelerator Laboratory Persis Drell, Director

    E-Print Network [OSTI]

    Quake, Stephen R.

    . Reichanadter, Acting ALD L. Dardzinski Interim Assistant Director LCLS Directorate J. Stöhr, ALD U. Bergmann, Facilities LCLS-II John Galayda Mechanical Engineering and Technical Support Division K. Fant Accelerator Research Division E. Colby LCLS Accelerator Systems Division A. Brachmann Instrumentation & Controls

  9. Some Frontiers of Accelerator Physics

    E-Print Network [OSTI]

    Sessler, Andrew M.

    2008-01-01T23:59:59.000Z

    Some Frontiers of Accelerator Physics A.M. Sessler OctoberSOME FRONTIERS OF ACCELERATOR PHYSICS* Andrew M. Sessleris Some Frontiers of Accelerator Physics and it is most

  10. Accelerating Particles with Plasma

    SciTech Connect (OSTI)

    Litos, Michael; Hogan, Mark

    2014-11-05T23:59:59.000Z

    Researchers at SLAC explain how they use plasma wakefields to accelerate bunches of electrons to very high energies over only a short distance. Their experiments offer a possible path for the future of particle accelerators.

  11. Research paper Os decay system applied to dating platinum-group element

    E-Print Network [OSTI]

    Reiners, Peter W.

    Dating Geochronology Bushveld PGM We evaluate the 190 Pt­186 Os decay system, measured by laser ablation. The 190 Pt­186 Os decay system, measured by laser ablation-multi- collector-inductively coupled plasma

  12. Combustion Group Group members

    E-Print Network [OSTI]

    Wang, Wei

    Combustion Group Group members: Thierry Poinsot, Emilien Courtine, Luc Vervisch, Benjamin Farcy § New combustion and energy-conversion concepts #12;Introduction Combustion research thrusts Combustion Dynamics and Flame-Stabilization Research objectives § Obtain fundamental understanding of combustion

  13. SATURATED FUSION SYSTEMS OVER 2-GROUPS BOB OLIVER AND JOANA VENTURA

    E-Print Network [OSTI]

    Oliver, Bob

    VENTURA Abstract. We develop methods for listing, for a given 2-group S, all nonc* *onstrained. Ventura is partially supported by FCT/POCTI/FEDER and grant PDCT/MAT/58497* */2004. 1 #12;2 BOB OLIVER AND JOANA VENTURA refer to Definition 2.3, Proposition 2

  14. Commnity Petascale Project for Accelerator Science and Simulation: Advancing Computational Science for Future Accelerators and Accelerator Technologies

    SciTech Connect (OSTI)

    Spentzouris, Panagiotis; /Fermilab; Cary, John; /Tech-X, Boulder; Mcinnes, Lois Curfman; /Argonne; Mori, Warren; /UCLA; Ng, Cho; /SLAC; Ng, Esmond; Ryne, Robert; /LBL, Berkeley

    2008-07-01T23:59:59.000Z

    The design and performance optimization of particle accelerators is essential for the success of the DOE scientific program in the next decade. Particle accelerators are very complex systems whose accurate description involves a large number of degrees of freedom and requires the inclusion of many physics processes. Building on the success of the SciDAC1 Accelerator Science and Technology project, the SciDAC2 Community Petascale Project for Accelerator Science and Simulation (ComPASS) is developing a comprehensive set of interoperable components for beam dynamics, electromagnetics, electron cooling, and laser/plasma acceleration modeling. ComPASS is providing accelerator scientists the tools required to enable the necessary accelerator simulation paradigm shift from high-fidelity single physics process modeling (covered under SciDAC1) to high-fidelity multi-physics modeling. Our computational frameworks have been used to model the behavior of a large number of accelerators and accelerator R&D experiments, assisting both their design and performance optimization. As parallel computational applications, the ComPASS codes have been shown to make effective use of thousands of processors.

  15. Commnity Petascale Project for Accelerator Science And Simulation: Advancing Computational Science for Future Accelerators And Accelerator Technologies

    SciTech Connect (OSTI)

    Spentzouris, Panagiotis; /Fermilab; Cary, John; /Tech-X, Boulder; Mcinnes, Lois Curfman; /Argonne; Mori, Warren; /UCLA; Ng, Cho; /SLAC; Ng, Esmond; Ryne, Robert; /LBL, Berkeley

    2011-10-21T23:59:59.000Z

    The design and performance optimization of particle accelerators are essential for the success of the DOE scientific program in the next decade. Particle accelerators are very complex systems whose accurate description involves a large number of degrees of freedom and requires the inclusion of many physics processes. Building on the success of the SciDAC-1 Accelerator Science and Technology project, the SciDAC-2 Community Petascale Project for Accelerator Science and Simulation (ComPASS) is developing a comprehensive set of interoperable components for beam dynamics, electromagnetics, electron cooling, and laser/plasma acceleration modelling. ComPASS is providing accelerator scientists the tools required to enable the necessary accelerator simulation paradigm shift from high-fidelity single physics process modeling (covered under SciDAC1) to high-fidelity multiphysics modeling. Our computational frameworks have been used to model the behavior of a large number of accelerators and accelerator R&D experiments, assisting both their design and performance optimization. As parallel computational applications, the ComPASS codes have been shown to make effective use of thousands of processors.

  16. USENIX Association NSDI '11: 8th USENIX Symposium on Networked Systems Design and Implementation 1 SSLShader: Cheap SSL Acceleration with Commodity Processors

    E-Print Network [OSTI]

    Moon, Sue B.

    SSLShader: Cheap SSL Acceleration with Commodity Processors Keon Jang+, Sangjin Han+, Seungyeop Han*, Sue. Unfortunately, today's SSL deployment is largely limited to security or privacy- critical domains. The low, and the cost of good privacy on the Internet is tightly bound to expensive hardware SSL accelerators

  17. High brightness electron accelerator

    DOE Patents [OSTI]

    Sheffield, Richard L. (Los Alamos, NM); Carlsten, Bruce E. (Los Alamos, NM); Young, Lloyd M. (Los Alamos, NM)

    1994-01-01T23:59:59.000Z

    A compact high brightness linear accelerator is provided for use, e.g., in a free electron laser. The accelerator has a first plurality of acclerating cavities having end walls with four coupling slots for accelerating electrons to high velocities in the absence of quadrupole fields. A second plurality of cavities receives the high velocity electrons for further acceleration, where each of the second cavities has end walls with two coupling slots for acceleration in the absence of dipole fields. The accelerator also includes a first cavity with an extended length to provide for phase matching the electron beam along the accelerating cavities. A solenoid is provided about the photocathode that emits the electons, where the solenoid is configured to provide a substantially uniform magnetic field over the photocathode surface to minimize emittance of the electons as the electrons enter the first cavity.

  18. SuperB Progress Report for Accelerator

    SciTech Connect (OSTI)

    Biagini, M.E.; Boni, R.; Boscolo, M.; Buonomo, B.; Demma, T.; Drago, A.; Esposito, M.; Guiducci, S.; Mazzitelli, G.; Pellegrino, L.; Preger, M.A.; Raimondi, P.; Ricci, R.; Rotundo, U.; Sanelli, C.; Serio, M.; Stella, A.; Tomassini, S.; Zobov, M.; /Frascati; Bertsche, K.; Brachman, A.; /SLAC /Novosibirsk, IYF /INFN, Pisa /Pisa U. /Orsay, LAL /Annecy, LAPP /LPSC, Grenoble /IRFU, SPP, Saclay /DESY /Cockroft Inst. Accel. Sci. Tech. /U. Liverpool /CERN

    2012-02-14T23:59:59.000Z

    This report details the progress made in by the SuperB Project in the area of the Collider since the publication of the SuperB Conceptual Design Report in 2007 and the Proceedings of SuperB Workshop VI in Valencia in 2008. With this document we propose a new electron positron colliding beam accelerator to be built in Italy to study flavor physics in the B-meson system at an energy of 10 GeV in the center-of-mass. This facility is called a high luminosity B-factory with a project name 'SuperB'. This project builds on a long history of successful e+e- colliders built around the world, as illustrated in Figure 1.1. The key advances in the design of this accelerator come from recent successes at the DAFNE collider at INFN in Frascati, Italy, at PEP-II at SLAC in California, USA, and at KEKB at KEK in Tsukuba Japan, and from new concepts in beam manipulation at the interaction region (IP) called 'crab waist'. This new collider comprises of two colliding beam rings, one at 4.2 GeV and one at 6.7 GeV, a common interaction region, a new injection system at full beam energies, and one of the two beams longitudinally polarized at the IP. Most of the new accelerator techniques needed for this collider have been achieved at other recently completed accelerators including the new PETRA-3 light source at DESY in Hamburg (Germany) and the upgraded DAFNE collider at the INFN laboratory at Frascati (Italy), or during design studies of CLIC or the International Linear Collider (ILC). The project is to be designed and constructed by a worldwide collaboration of accelerator and engineering staff along with ties to industry. To save significant construction costs, many components from the PEP-II collider at SLAC will be recycled and used in this new accelerator. The interaction region will be designed in collaboration with the particle physics detector to guarantee successful mutual use. The accelerator collaboration will consist of several groups at present universities and national laboratories. In Italy these may include INFN Frascati and the University of Pisa, in the United States SLAC, LBNL, BNL and several universities, in France IN2P3, LAPP, and Grenoble, in Russia BINP, in Poland Krakow University, and in the UK the Cockcroft Institute. The construction time for this collider is a total of about four years. The new tunnel can be bored in about a year. The new accelerator components can be built and installed in about 4 years. The shipping of components from PEP-II at SLAC to Italy will take about a year. A new linac and damping ring complex for the injector for the rings can be built in about three years. The commissioning of this new accelerator will take about a year including the new electron and positron sources, new linac, new damping ring, new beam transport lines, two new collider rings and the Interaction Region. The new particle physics detector can be commissioned simultaneously with the accelerator. Once beam collisions start for particle physics, the luminosity will increase with time, likely reaching full design specifications after about two to three years of operation. After construction, the operation of the collider will be the responsibility of the Italian INFN governmental agency. The intent is to run this accelerator about ten months each year with about one month for accelerator turn-on and nine months for colliding beams. The collider will need to operate for about 10 years to provide the required 50 ab{sup -1} requested by the detector collaboration. Both beams as anticipated in this collider will have properties that are excellent for use as sources for synchrotron radiation (SR). The expected photon properties are comparable to those of PETRA-3 or NSLS-II. The beam lines and user facilities needed to carry out this SR program are being investigated.

  19. Diffusive Acceleration of Ions at Interplanetary Shocks

    E-Print Network [OSTI]

    Matthew G. Baring; Errol J. Summerlin

    2005-06-08T23:59:59.000Z

    Heliospheric shocks are excellent systems for testing theories of particle acceleration in their environs. These generally fall into two classes: (1) interplanetary shocks that are linear in their ion acceleration characteristics, with the non-thermal ions serving as test particles, and (2) non-linear systems such as the Earth's bow shock and the solar wind termination shock, where the accelerated ions strongly influence the magnetohydrodynamic structure of the shock. This paper explores the modelling of diffusive acceleration at a particular interplanetary shock, with an emphasis on explaining in situ measurements of ion distribution functions. The observational data for this event was acquired on day 292 of 1991 by the Ulysses mission. The modeling is performed using a well-known kinetic Monte Carlo simulation, which has yielded good agreement with observations at several heliospheric shocks, as have other theoretical techniques, namely hybrid plasma simulations, and numerical solution of the diffusion-convection equation. In this theory/data comparison, it is demonstrated that diffusive acceleration theory can, to first order, successfully account for both the proton distribution data near the shock, and the observation of energetic protons farther upstream of this interplanetary shock than lower energy pick-up protons, using a single turbulence parameter. The principal conclusion is that diffusive acceleration of inflowing upstream ions can model this pick-up ion-rich event without the invoking any seed pre-acceleration mechanism, though this investigation does not rule out the action of such pre-acceleration.

  20. J. A. Stiver, P. J. Antsaklis and M. D. Lemmon , "A Logical DES Approach to the Design of Hybrid Control Systems," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group,

    E-Print Network [OSTI]

    Antsaklis, Panos

    Control Systems," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS-93-006, Univ of Notre Dame, October 1993. #12;Controller Interface Plant r x r x Control Systems," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group

  1. M. D. Lemmon and P. J. Antsaklis, "On The Stability of Logical Transitions in Hybrid Control Systems," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS-93-009,

    E-Print Network [OSTI]

    Antsaklis, Panos

    Systems," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS of Logical Transitions in Hybrid Control Systems," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS-93-009, Univ of Notre Dame, December 1993. #12;M. D. Lemmon and P. J

  2. PRODUCTION AND APPLICATIONS OF NEUTRONS USING PARTICLE ACCELERATORS

    SciTech Connect (OSTI)

    David L. Chichester

    2009-11-01T23:59:59.000Z

    Advances in neutron science have gone hand in hand with the development and of particle accelerators from the beginning of both fields of study. Early accelerator systems were developed simply to produce neutrons, allowing scientists to study their properties and how neutrons interact in matter, but people quickly realized that more tangible uses existed too. Today the diversity of applications for industrial accelerator-based neutron sources is high and so to is the actual number of instruments in daily use is high, and they serve important roles in the fields where they're used. This chapter presents a technical introduction to the different ways particle accelerators are used to produce neutrons, an historical overview of the early development of neutron-producing particle accelerators, a description of some current industrial accelerator systems, narratives of the fields where neutron-producing particle accelerators are used today, and comments on future trends in the industrial uses of neutron producing particle accelerators.

  3. Mortuary practices and death beliefs: the effects of the culture group as a system

    E-Print Network [OSTI]

    Gardner, Karen Mae

    1988-01-01T23:59:59.000Z

    the sum of its parts, possessing what is known as wholeness. As a whole, it possesses characteristics which are not possessed by it parts singly (Laszlo 1973:36). It is not the nature of the components in and of themselves that are basic to the system... with varying forms of stimuli. The presence of both fixed forces and unrestrained forces allows the system to be capable of modification through the interplay of these forces (Laszlo 19i3:39). This permits the system to continually develop and change...

  4. Working Group Report on - Space Nuclear Power Systems and Nuclear Waste

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradley NickellApril 16, 2008Ms.12.1AJanuaryEnergyTechnology

  5. Roadmap-Based Techniques for Modeling Group Behaviors in Multi-Agent Systems 

    E-Print Network [OSTI]

    Rodriguez, Samuel Oscar

    2012-07-16T23:59:59.000Z

    Simulating large numbers of agents, performing complex behaviors in realistic environments is a difficult problem with applications in robotics, computer graphics and animation. A multi-agent system can be a useful tool ...

  6. Disruption of the group health insurance in light of the Affordable Care Act - system approach

    E-Print Network [OSTI]

    Shefali, Shweta

    2014-01-01T23:59:59.000Z

    Our current Healthcare system has multiple problems and it is widely perceived that it is not able to provide quality affordable healthcare to all Americans; millions of Americans are without Health Insurance. The Affordable ...

  7. ISSIGreviewProject Management Institute--Information Systems Specific Interest Group Fourth Quarter 2000

    E-Print Network [OSTI]

    2000 Volume 10, Number 4 Supporting Project Management in an Information Systems Environment PMI & SIG News:PMI & SIG News:PMI & SIG News:PMI & SIG News:PMI & SIG News: ISSIG Communications Update

  8. Roadmap-Based Techniques for Modeling Group Behaviors in Multi-Agent Systems

    E-Print Network [OSTI]

    Rodriguez, Samuel Oscar

    2012-07-16T23:59:59.000Z

    Simulating large numbers of agents, performing complex behaviors in realistic environments is a difficult problem with applications in robotics, computer graphics and animation. A multi-agent system can be a useful tool for studying a range...

  9. M. D. Lemmon and P. J. Antsaklis, "Towards a Working Characterization of "Intelligent" Supervisory Control," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS-

    E-Print Network [OSTI]

    Antsaklis, Panos

    Control," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS Characterization of "Intelligent" Supervisory Control," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS- 93-007, Univ of Notre Dame, November 1993. #12;M. D. Lemmon and P. J

  10. Leaky Fermi accelerators

    E-Print Network [OSTI]

    Shah, Kushal; Rom-Kedar, Vered; Turaev, Dmitry

    2015-01-01T23:59:59.000Z

    A Fermi accelerator is a billiard with oscillating walls. A leaky accelerator interacts with an environment of an ideal gas at equilibrium by exchange of particles through a small hole on its boundary. Such interaction may heat the gas: we estimate the net energy flow through the hole under the assumption that the particles inside the billiard do not collide with each other and remain in the accelerator for sufficiently long time. The heat production is found to depend strongly on the type of the Fermi accelerator. An ergodic accelerator, i.e. one which has a single ergodic component, produces a weaker energy flow than a multi-component accelerator. Specifically, in the ergodic case the energy gain is independent of the hole size, whereas in the multi-component case the energy flow may be significantly increased by shrinking the hole size.

  11. THE DIELECTRIC WALL ACCELERATOR

    SciTech Connect (OSTI)

    Caporaso, G J; Chen, Y; Sampayan, S E

    2009-08-17T23:59:59.000Z

    The Dielectric Wall Accelerator (DWA), a class of induction accelerators, employs a novel insulating beam tube to impress a longitudinal electric field on a bunch of charged particles. The surface flashover characteristics of this tube may permit the attainment of accelerating gradients on the order of 100 MV/m for accelerating pulses on the order of a nanosecond in duration. A virtual traveling wave of excitation along the tube is produced at any desired speed by controlling the timing of pulse generating modules that supply a tangential electric field to the tube wall. Because of the ability to control the speed of this virtual wave, the accelerator is capable of handling any charge to mass ratio particle; hence it can be used for electrons, protons and any ion. The accelerator architectures, key technologies and development challenges will be described.

  12. Privacy and Security Research Group workshop on network and distributed system security: Proceedings

    SciTech Connect (OSTI)

    Not Available

    1993-05-01T23:59:59.000Z

    This report contains papers on the following topics: NREN Security Issues: Policies and Technologies; Layer Wars: Protect the Internet with Network Layer Security; Electronic Commission Management; Workflow 2000 - Electronic Document Authorization in Practice; Security Issues of a UNIX PEM Implementation; Implementing Privacy Enhanced Mail on VMS; Distributed Public Key Certificate Management; Protecting the Integrity of Privacy-enhanced Electronic Mail; Practical Authorization in Large Heterogeneous Distributed Systems; Security Issues in the Truffles File System; Issues surrounding the use of Cryptographic Algorithms and Smart Card Applications; Smart Card Augmentation of Kerberos; and An Overview of the Advanced Smart Card Access Control System. Selected papers were processed separately for inclusion in the Energy Science and Technology Database.

  13. Particle acceleration in electron-ion jets

    E-Print Network [OSTI]

    K. -I. Nishikawa; P. Hardee; C. B. Hededal; G. Richardson; R. Preece; H. Sol; G. J. Fishman; C. Kouvelioutou; Y. Mizuno

    2005-09-20T23:59:59.000Z

    Weibel instability created in collisionless shocks is responsible for particle (electron, positron, and ion) acceleration. Using a 3-D relativistic electromagnetic particle (REMP) code, we have investigated particle acceleration associated with a relativistic electron-ion jet fronts propagating into an ambient plasma without initial magnetic fields with a longer simulation system in order to investigate nonlinear stage of the Weibel instability and its acceleration mechanism. The current channels generated by the Weibel instability induce the radial electric fields. The z component of the Poynting vector (E x B) become positive in the large region along the jet propagation direction. This leads to the acceleration of jet electrons along the jet. In particular the E x B drift with the large scale current channel generated by the ion Weibel instability accelerate electrons effectively in both parallel and perpendicular directions.

  14. Optically pulsed electron accelerator

    DOE Patents [OSTI]

    Fraser, J.S.; Sheffield, R.L.

    1985-05-20T23:59:59.000Z

    An optically pulsed electron accelerator can be used as an injector for a free electron laser and comprises a pulsed light source, such as a laser, for providing discrete incident light pulses. A photoemissive electron source emits electron bursts having the same duration as the incident light pulses when impinged upon by same. The photoemissive electron source is located on an inside wall of a radiofrequency-powered accelerator cell which accelerates the electron burst emitted by the photoemissive electron source.

  15. Optically pulsed electron accelerator

    DOE Patents [OSTI]

    Fraser, John S. (Los Alamos, NM); Sheffield, Richard L. (Los Alamos, NM)

    1987-01-01T23:59:59.000Z

    An optically pulsed electron accelerator can be used as an injector for a free electron laser and comprises a pulsed light source, such as a laser, for providing discrete incident light pulses. A photoemissive electron source emits electron bursts having the same duration as the incident light pulses when impinged upon by same. The photoemissive electron source is located on an inside wall of a radio frequency powered accelerator cell which accelerates the electron burst emitted by the photoemissive electron source.

  16. Muon Collider Progress: Accelerators

    E-Print Network [OSTI]

    Michael S. Zisman

    2011-09-14T23:59:59.000Z

    A muon collider would be a powerful tool for exploring the energy-frontier with leptons, and would complement the studies now under way at the LHC. Such a device would offer several important benefits. Muons, like electrons, are point particles so the full center-of-mass energy is available for particle production. Moreover, on account of their higher mass, muons give rise to very little synchrotron radiation and produce very little beamstrahlung. The first feature permits the use of a circular collider that can make efficient use of the expensive rf system and whose footprint is compatible with an existing laboratory site. The second feature leads to a relatively narrow energy spread at the collision point. Designing an accelerator complex for a muon collider is a challenging task. Firstly, the muons are produced as a tertiary beam, so a high-power proton beam and a target that can withstand it are needed to provide the required luminosity of ~1 \\times 10^34 cm^-2s^-1. Secondly, the beam is initially produced with a large 6D phase space, which necessitates a scheme for reducing the muon beam emittance ("cooling"). Finally, the muon has a short lifetime so all beam manipulations must be done very rapidly. The Muon Accelerator Program, led by Fermilab and including a number of U.S. national laboratories and universities, has undertaken design and R&D activities aimed toward the eventual construction of a muon collider. Design features of such a facility and the supporting R&D program are described.

  17. Machine Protection: Availability for Particle Accelerators

    E-Print Network [OSTI]

    Apollonio, Andrea; Schmidt, Ruediger

    2015-03-16T23:59:59.000Z

    Machine availability is a key indicator for the performance of the next generation of particle accelerators. Availability requirements need to be carefully considered during the design phase to achieve challenging objectives in different fields, as e.g. particle physics and material science. For existing and future High-Power facilities, such as ESS (European Spallation Source) and HL-LHC (High-Luminosity LHC), operation with unprecedented beam power requires highly dependable Machine Protection Systems (MPS) to avoid any damage-induced downtime. Due to the high complexity of accelerator systems, finding the optimal balance between equipment safety and accelerator availability is challenging. The MPS architecture, as well as the choice of electronic components, have a large influence on the achievable level of availability. In this thesis novel methods to address the availability of accelerators and their protection systems are presented. Examples of studies related to dependable MPS architectures are given i...

  18. Advanced Accelerator Concepts Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    on high energy ion generation Levi Schachter Active Media Accelerators Benjamin Bowes Ultrafast 2-D radiative transport in a micron-scale aluminum plasma excited at...

  19. Accelerator Test Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Test Facility Vitaly Yakimenko October 6-7, 2010 ATF User meeting DOE HE, S. Vigdor, ALD - (Contact) T. Ludlam Chair, Physics Department V. Yakimenko Director ATF, Accelerator...

  20. Accelerator Concepts Workshop

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Colliders to Synchrotron Radiation Sources. The wide scope of the workshop includes new methods of particle acceleration to high energies, techniques for production of...

  1. Charged particle accelerator grating

    DOE Patents [OSTI]

    Palmer, Robert B. (Shoreham, NY)

    1986-01-01T23:59:59.000Z

    A readily disposable and replaceable accelerator grating for a relativistic particle accelerator. The grating is formed for a plurality of liquid droplets that are directed in precisely positioned jet streams to periodically dispose rows of droplets along the borders of a predetermined particle beam path. A plurality of lasers are used to direct laser beams into the droplets, at predetermined angles, thereby to excite the droplets to support electromagnetic accelerating resonances on their surfaces. Those resonances operate to accelerate and focus particles moving along the beam path. As the droplets are distorted or destroyed by the incoming radiation, they are replaced at a predetermined frequency by other droplets supplied through the jet streams.

  2. Accelerator R&D

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Superconducting RF Module with a PBG Coupler Cell, 2013 North American Particle Accelerator Conference, Pasadena, CA, September 29 - October 4th, 2013. Evgenya I. Simakov,...

  3. Market Acceleration (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-09-01T23:59:59.000Z

    The fact sheet summarizes the goals and activities of the DOE Solar Energy Technologies Program efforts within its market acceleration subprogram.

  4. Hydrogen Analysis Group

    SciTech Connect (OSTI)

    Not Available

    2008-03-01T23:59:59.000Z

    NREL factsheet that describes the general activites of the Hydrogen Analysis Group within NREL's Hydrogen Technologies and Systems Center.

  5. Carbon star populations in systems with different metallicities: statistics in Local Group galaxies

    E-Print Network [OSTI]

    M. Mouhcine; A. Lancon

    2002-09-03T23:59:59.000Z

    We present evolutionary population synthesis models for the study of the cool and luminous intermediate age stellar populations in resolved galaxies with particular emphasis on carbon star populations. We study the effects of the star formation history, the age and the metallicity on the populations of intermediate mass stars. In the case of instantaneous bursts, we confirm that lower metallicity results in higher contribution of carbon stars to the total star number, and in higher number ratios of carbon stars to late-type M stars. Chemically consistent models are used to study the effect of the star formation history on the relations between carbon star population properties and global parameters of the parent galaxy (age, metallicity). Our models are able to account, for the first time, for those correlations, as observed in the galaxies of the Local Group. For stellar populations older than 1 Gyr, the properties of carbon star populations are linked to the current metallicity in a way that is quite independent of the star formation scenario. The number of carbon stars to late-type M stars forms a metallicity sequence along which stellar populations with very different star formation histories are found (Abridged).

  6. Particle-acceleration timescales in TeV blazar flares

    E-Print Network [OSTI]

    Joni Tammi; Peter Duffy

    2008-12-01T23:59:59.000Z

    Observations of minute-scale flares in TeV Blazars place constraints on particle acceleration mechanisms in those objects. The implications for a variety of radiation mechanisms have been addressed in the literature; in this paper we compare four different acceleration mechanisms: diffusive shock acceleration, second-order Fermi, shear acceleration and the converter mechanism. When the acceleration timescales and radiative losses are taken into account, we can exclude shear acceleration and the neutron-based converted mechanism as possible acceleration processes in these systems. The first-order Fermi process and the converter mechanism working via SSC photons are still practically instantaneous, however, provided sufficient turbulence is generated on the timescale of seconds. We propose stochastic acceleration as a promising candidate for the energy-dependent time delays in recent gamma-ray flares of Markarian 501.

  7. Community petascale project for accelerator science and simulation: Advancing computational science for future accelerators and accelerator technologies

    E-Print Network [OSTI]

    Spentzouris, Panagiotis

    2008-01-01T23:59:59.000Z

    program for computational accelerator physics development isof computational accelerator physics applications, withof computational accelerator physics. Under ComPASS, the

  8. aps linear accelerator: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    description of the APS and its documented numerous minor changes to accelerator system technical descriptions to ensure those descriptions Kemner, Ken 97 3-D Model of Broadband...

  9. accelerator driven neutron: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    effects of this term from being periodic. Brett D. Altschul 1999-04-11 8 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  10. accelerator driven hybrid: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rubbia, Carlo; Burgio, N; Carta, M; Santagata, A; Cinotti, L 2002-01-01 45 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  11. ads accelerator driven: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rubbia, Carlo; Burgio, N; Carta, M; Santagata, A; Cinotti, L 2002-01-01 19 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  12. accelerator-driven transmutation technologies: Topics by E-print...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    as the European ADS technology demonstrator. Alex C. Mueller 2012-10-16 7 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  13. accelerator driven reactors: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    discover a finite theta13 by observing Y. Obayashi 2008-07-25 39 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  14. accelerator-driven transmutation technology: Topics by E-print...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    as the European ADS technology demonstrator. Alex C. Mueller 2012-10-16 7 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  15. The Klynac: An Integrated Klystron and Linear Accelerator

    SciTech Connect (OSTI)

    Potter, J. M., Schwellenbach, D., Meidinger, A.

    2012-08-07T23:59:59.000Z

    The Klynac concept integrates an electron gun, a radio frequency (RF) power source, and a coupled-cavity linear accelerator into a single resonant system

  16. accelerated carbon ion: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    as test particles, and (2) non-linear systems such as the Earth's bow shock and the solar wind termination shock, where the accelerated ions strongly influence the...

  17. Neutrino physics at accelerators

    E-Print Network [OSTI]

    Enrique Fernandez

    2006-07-16T23:59:59.000Z

    Present and future neutrino experiments at accelerators are mainly concerned with understanding the neutrino oscillation phenomenon and its implications. Here a brief account of neutrino oscillations is given together with a description of the supporting data. Some current and planned accelerator neutrino experiments are also explained.

  18. Microscale acceleration history discriminators

    DOE Patents [OSTI]

    Polosky, Marc A. (Albuquerque, NM); Plummer, David W. (Albuquerque, NM)

    2002-01-01T23:59:59.000Z

    A new class of micromechanical acceleration history discriminators is claimed. These discriminators allow the precise differentiation of a wide range of acceleration-time histories, thereby allowing adaptive events to be triggered in response to the severity (or lack thereof) of an external environment. Such devices have applications in airbag activation, and other safety and surety applications.

  19. Accelerators (4/5)

    ScienceCinema (OSTI)

    None

    2011-10-06T23:59:59.000Z

    1a) Introduction and motivation 1b) History and accelerator types 2) Transverse beam dynamics 3a) Longitudinal beam dynamics 3b) Figure of merit of a synchrotron/collider 3c) Beam control 4) Main limiting factors 5) Technical challenges Prerequisite knowledge: Previous knowledge of accelerators is not required.

  20. Accelerators (5/5)

    ScienceCinema (OSTI)

    None

    2011-10-06T23:59:59.000Z

    1a) Introduction and motivation 1b) History and accelerator types 2) Transverse beam dynamics 3a) Longitudinal beam dynamics 3b) Figure of merit of a synchrotron/collider 3c) Beam control 4) Main limiting factors 5) Technical challenges Prerequisite knowledge: Previous knowledge of accelerators is not required.

  1. Safety of Accelerator Facilities

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2004-07-23T23:59:59.000Z

    To establish accelerator-specific safety requirements which, when supplemented by other applicable safety and health requirements, will serve to prevent injuries and illnesses associated with Department of Energy (DOE) or National Nuclear Security Administration (NNSA) accelerator operations. Cancels DOE O 420.2A. Certified 5-13-08. Canceled by DOE O 420.2C.

  2. Accelerators (3/5)

    ScienceCinema (OSTI)

    None

    2011-10-06T23:59:59.000Z

    1a) Introduction and motivation 1b) History and accelerator types 2) Transverse beam dynamics 3a) Longitudinal beam dynamics 3b) Figure of merit of a synchrotron/collider 3c) Beam control 4) Main limiting factors 5) Technical challenges Prerequisite knowledge: Previous knowledge of accelerators is not required.

  3. Safety of Accelerator Facilities

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-07-21T23:59:59.000Z

    The order defines accelerators and establishes accelerator specific safety requirements and approval authorities which, when supplemented by other applicable safety and health requirements, promote safe operations to ensure protection of workers, the public, and the environment. Cancels DOE O 420.2B.

  4. Safety of Accelerator Facilities

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-01-08T23:59:59.000Z

    To establish accelerator-specific safety requirements which, when supplemented by other applicable safety and health requirements, will serve to prevent injuries and illnesses associated with Department of Energy (DOE) or National Nuclear Security Administration (NNSA) accelerator operations. Cancels DOE O 420.2. Canceled by DOE O 420.2B.

  5. Solar PV Manufacturing Cost Model Group: Installed Solar PV System Prices (Presentation)

    SciTech Connect (OSTI)

    Goodrich, A. C.; Woodhouse, M.; James, T.

    2011-02-01T23:59:59.000Z

    EERE's Solar Energy Technologies Program is charged with leading the Secretary's SunShot Initiative to reduce the cost of electricity from solar by 75% to be cost competitive with conventional energy sources without subsidy by the end of the decade. As part of this Initiative, the program has funded the National Renewable Energy Laboratory (NREL) to develop module manufacturing and solar PV system installation cost models to ensure that the program's cost reduction targets are carefully aligned with current and near term industry costs. The NREL cost analysis team has leveraged the laboratories' extensive experience in the areas of project finance and deployment, as well as industry partnerships, to develop cost models that mirror the project cost analysis tools used by project managers at leading U.S. installers. The cost models are constructed through a "bottoms-up" assessment of each major cost element, beginning with the system's bill of materials, labor requirements (type and hours) by component, site-specific charges, and soft costs. In addition to the relevant engineering, procurement, and construction costs, the models also consider all relevant costs to an installer, including labor burdens and overhead rates, supply chain costs, and overhead and materials inventory costs, and assume market-specific profits.

  6. CH2M Hill Hanford Group, Inc. Standards and Requirements Identification Document (SRID) Requirements Management System and Requirements Specification

    SciTech Connect (OSTI)

    JOHNSON, A.L.

    2000-11-30T23:59:59.000Z

    The current Tank Farm Contractor (TFC) for the U. S. Department of Energy, Office of River Protection (ORP), River Protection Project (RPP), CH2M Hill Hanford Group, Inc. (CHG), will use a computer based requirements management system. The system will serve as a tool to assist in identifying, capturing, and maintaining the Standards/Requirements Identification Document (S/RID) requirements and links to implementing procedures and other documents. By managing requirements as one integrated set, CHG will be able to carry out its mission more efficiently and effectively. CHG has chosen the Dynamic Object Oriented Requirements System (DOORS{trademark}) as the preferred computer based requirements management system. Accordingly, the S/RID program will use DOORS{trademark}. DOORS{trademark} will replace the Environmental Requirements Management Interface (ERMI) system as the tool for S/RID data management. The DOORS{trademark} S/RID test project currently resides on the DOORSTM test server. The S/RID project will be migrated to the DOORS{trademark} production server. After the migration the S/RID project will be considered a production project and will no longer reside on the test server.

  7. Accelerated Quantum Dynamics

    E-Print Network [OSTI]

    Lynch, Morgan H

    2015-01-01T23:59:59.000Z

    In this paper we establish a formalism for the computation of observables due to acceleration-induced particle physics processes. General expressions for the transition rate, multiplicity, power, spectra, and displacement law of particles undergoing time-dependent acceleration and transitioning into a final state of arbitrary particle number are obtained. The transition rate, power, and spectra are characterised by unique polynomials of multiplicity and thermal distributions of both bosonic and fermionic statistics. The acceleration dependent multiplicity is computed in terms of the branching fractions of the associated inertial processes. The displacement law of the spectra predicts the energy of the emitted particles are directly proportional to the accelerated temperature. These results extend our understanding of particle physics into the high acceleration sector.

  8. ACCELERATED DESTRUCTIVE DEGRADATION TESTS: DATA, MODELS,

    E-Print Network [OSTI]

    ACCELERATED DESTRUCTIVE DEGRADATION TESTS: DATA, MODELS, AND ANALYSIS Luis A. Escobar Dept Group Hewlett-Packard Corvallis, OR 97330, USA Abstract Degradation data analysis is a powerful tool for reliability assessment. Useful reliability information is available from degradation data when there are few

  9. Inverse free-electron laser accelerator

    SciTech Connect (OSTI)

    Pellegrini, C.; Campisi, R.

    1982-01-01T23:59:59.000Z

    We first describe the basic physical properties of an inverse free-electron laser and make an estimate of the order of magnitude of the accelerating field obtainable with such a system; then apply the general ideas to the design of an actual device and through this example we give a more accurate evaluation of the fundamental as well as the technical limitations that this acceleration scheme imposes.

  10. Determination of thiol functional groups on bacteria and natural organic matter in environmental systems

    SciTech Connect (OSTI)

    Anandha Rao, Balaji [ORNL] [ORNL; Lin, Hui [ORNL] [ORNL; Liang, Liyuan [ORNL] [ORNL; Gu, Baohua [ORNL] [ORNL

    2014-01-01T23:59:59.000Z

    Organic thiols (R-SH) are known to react and form complexes with some toxic soft metals such as mercury (Hg) in both biotic and abiotic systems. However, a clear understanding of these interactions is currently limited because quantifying thiols in environmental matrices is difficult due to their low abundance, susceptibility to oxidation, and measurement interference by non-thiol compounds in samples. Here, we report a fluorescence-labeling method using a maleimide containing probe, ThioGlo-1 (TG-1), to determine total thiols directly on bacterial cells and natural organic matter (NOM). We systematically evaluated the optimal thiol labeling conditions and interference from organic compounds such as disulfide, methionine, thiourea, and amine, and inorganic ions such as Na+, K+, Ca2+, Fe2+, Cl-, SO42-, HCO3-, and SCN-, and found that the method is highly sensitive and selective. Only relatively high levels of sulfide (S2-) and sulfite (SO32-) significantly interfere with the thiol analysis. The method was successful in determining thiols in a bacterium Geobacter sulfurreducens PCA and its mutants in a phosphate buffered saline solution. The measured value of ~2.1 104 thiols cell-1 (or ~0.07 mol g-1 wet cells) is in good agreement with that observed during reactions between Hg and PCA cells. Using the standard addition, we determined the total thiols of two reference NOM samples, the reduced Elliot soil humic acid and Suwanee River NOM, to be 3.6 and 0.7 mol g-1, respectively, consistent with those obtained based on their reactions with Hg.

  11. Jar mechanism accelerator

    SciTech Connect (OSTI)

    Anderson, E.A.; Webb, D.D.

    1989-07-11T23:59:59.000Z

    This patent describes an accelerator for use with a jar mechanism in a well pipe string to enhance the jarring impact delivered to a stuck object wherein the jar mechanism includes inner and outer members for connection, respectively, between the well pipe string the stuck object. The jar mechanism members are constructed to (1) restrict relative longitudinal movement therebetween to build up energy in the well pipe string and accelerator and then (2) to release the jar mechanism members for unrestrained, free relative longitudinal movement therebetween to engage jarring surfaces on the jar mechanism members for delivering a jarring impact to the stuck object. The accelerator includes: inner and outer telescopically connected members relatively movable longitudinally to accumulate energy in the accelerator; the inner and outer accelerator members each having means for connecting the accelerator in the well pipe string; means associated with the inner and outer members for initially accomodating a predetermined minimum length of unrestrained, free relative longitudinal movement between the inner and outer accelerator members.

  12. CO2 LASER TECHNOLOGY FOR ADVANCED PARTICLE ACCELERATORS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Actually, in this case, we talk about evanescent EM fields vanishing within a l -thick layer above the surface. In the third group of methods, particles are accelerated not by EM...

  13. This paper has been downloaded from the Building and Environmental Thermal Systems Research Group at Oklahoma State University (www.hvac.okstate.edu)

    E-Print Network [OSTI]

    Ghajar, Afshin J.

    to reductions in electrical energy usage, and allow more effective demand-side management. However, comparedThis paper has been downloaded from the Building and Environmental Thermal Systems Research Group

  14. Charged particle accelerator grating

    DOE Patents [OSTI]

    Palmer, R.B.

    1985-09-09T23:59:59.000Z

    A readily disposable and replaceable accelerator grating for a relativistic particle accelerator is described. The grating is formed for a plurality of liquid droplets that are directed in precisely positioned jet streams to periodically dispose rows of droplets along the borders of a predetermined particle beam path. A plurality of lasers are used to direct laser beams onto the droplets, at predetermined angles, thereby to excite the droplets to support electromagnetic accelerating resonances on their surfaces. Those resonances operate to accelerate and focus particles moving along the beam path. As the droplets are distorted or destroyed by the incoming radiation, they are replaced at a predetermined frequency by other droplets supplied through the jet streams.

  15. Accelerator on a Chip

    ScienceCinema (OSTI)

    England, Joel

    2014-07-16T23:59:59.000Z

    SLAC's Joel England explains how the same fabrication techniques used for silicon computer microchips allowed their team to create the new laser-driven particle accelerator chips. (SLAC Multimedia Communications)

  16. BNL | Accelerator Test Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and new approaches to particle acceleration and x-ray generation. A next-generation ultra-fast CO2 laser based on chirped pulse amplification in isotopic gas mixtures is...

  17. Design and producing of fine-group cross section library HENDL3.0/FG for subcritical system

    SciTech Connect (OSTI)

    Zou, J.; Zeng, Q.; Xu, D.; Hu, L.; Long, P. [Inst. of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); School of Nuclear Science and Technology, Univ. of Science and Technology of China, No.350 Shushanhu Road, Shushan District, Hefei, Anhui, 230031 (China)

    2012-07-01T23:59:59.000Z

    To improve the accuracy of the neutron analyses for subcritical system with thermal fission blanket, a coupled neutron and photon (315 n + 42{gamma}) fine-group cross section library HENDL3.0/FG based on ENDF/B-VII, JEFF3.1 and JENDL3.3 was produced by FDS team. In order to test the availability and reliability of the HENDL3.0/FG data library, shielding and critical safety benchmarks were performed with VisualBUS code. The testing results indicated that the discrepancy between calculation and experimental values of nuclear parameters fell in a reasonable range. It showed that the nuclear data library had accuracy and availability. (authors)

  18. CEBAF accelerator achievements

    SciTech Connect (OSTI)

    Y.C. Chao, M. Drury, C. Hovater, A. Hutton, G.A. Krafft, M. Poelker, C. Reece, M. Tiefenback

    2011-06-01T23:59:59.000Z

    In the past decade, nuclear physics users of Jefferson Lab's Continuous Electron Beam Accelerator Facility (CEBAF) have benefited from accelerator physics advances and machine improvements. As of early 2011, CEBAF operates routinely at 6 GeV, with a 12 GeV upgrade underway. This article reports highlights of CEBAF's scientific and technological evolution in the areas of cryomodule refurbishment, RF control, polarized source development, beam transport for parity experiments, magnets and hysteresis handling, beam breakup, and helium refrigerator operational optimization.

  19. Breakthrough: Fermilab Accelerator Technology

    ScienceCinema (OSTI)

    None

    2014-08-12T23:59:59.000Z

    There are more than 30,000 particle accelerators in operation around the world. At Fermilab, scientists are collaborating with other laboratories and industry to optimize the manufacturing processes for a new type of powerful accelerator that uses superconducting niobium cavities. Experimenting with unique polishing materials, a Fermilab team has now developed an efficient and environmentally friendly way of creating cavities that can propel particles with more than 30 million volts per meter.

  20. P. J. Antsaklis, M. D. Lemmon and J. A. Stiver, "Hybrid System Modeling and Event Identification," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS-93-002,

    E-Print Network [OSTI]

    Antsaklis, Panos

    ," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS-93-002, Univ and Event Identification," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS-93-002, Univ of Notre Dame, January 1993. #12;P. J. Antsaklis, M. D. Lemmon and J. A

  1. APT accelerator technology

    SciTech Connect (OSTI)

    Schneider, J.D.

    1996-09-01T23:59:59.000Z

    Proposed accelerator production of tritium (APT) project requires an accelerator providing a cw proton beam of 100 mA at 1300 MeV. Since most of the technical risk of a high-current cw (continuous-wave, 100% DF) accelerator resides in the low-energy section, Los Alamos is building a 20 MeV duplicate of the accelerator front end to confirm design codes, beam performance, and demonstrate operaional reliability. We report on design details of this low-energy demonstration accelerator (LEDA) and discuss the integrated design of the full accelerator for the APT plant. LEDA`s proton injector is under test and has produced more than 130 mA at 75 keV. Fabrication is proceeding on a 6.7-KeV, 8-m long RFQ, and detailed design is underway on coupled-cavity drift-tube linac (CCDTL) structures. Detailed design and technology experiments are underway on medium-beta superconducting cavities to assess feasibility of replacing the conventional (room-temperature copper) high-energy linac with a linac made of niobium superconducting RF cavities.

  2. Mechanical Engineering & Thermal Group

    E-Print Network [OSTI]

    Mojzsis, Stephen J.

    Mechanical Engineering & Thermal Group The Mechanical Engineering (ME) & Thermal Group at LASP has · STOP (Structural, Thermal, and Optical Performance) analyses of optical systems Thermal engineers lead evolved with the complexity of instrument design demands, LASP mechanical engineers develop advanced

  3. Plasma-based accelerator structures

    SciTech Connect (OSTI)

    Schroeder, Carl B.

    1999-12-01T23:59:59.000Z

    Plasma-based accelerators have the ability to sustain extremely large accelerating gradients, with possible high-energy physics applications. This dissertation further develops the theory of plasma-based accelerators by addressing three topics: the performance of a hollow plasma channel as an accelerating structure, the generation of ultrashort electron bunches, and the propagation of laser pulses is underdense plasmas.

  4. Fermilab | Science | Particle Accelerators | Fermilab's Accelerator Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem NotEnergy,ARMFormsGasReleaseSpeechesHall A ThisFermilab's Accelerator Complex photo

  5. Fermilab | Science | Particle Accelerators | Leading Accelerator Technology

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem NotEnergy,ARMFormsGasReleaseSpeechesHall A ThisFermilab's Accelerator ComplexLeading

  6. Accelerating DSMC data extraction.

    SciTech Connect (OSTI)

    Gallis, Michail A.; Piekos, Edward Stanley

    2006-10-01T23:59:59.000Z

    In many direct simulation Monte Carlo (DSMC) simulations, the majority of computation time is consumed after the flowfield reaches a steady state. This situation occurs when the desired output quantities are small compared to the background fluctuations. For example, gas flows in many microelectromechanical systems (MEMS) have mean speeds more than two orders of magnitude smaller than the thermal speeds of the molecules themselves. The current solution to this problem is to collect sufficient samples to achieve the desired resolution. This can be an arduous process because the error is inversely proportional to the square root of the number of samples so we must, for example, quadruple the samples to cut the error in half. This work is intended to improve this situation by employing more advanced techniques, from fields other than solely statistics, for determining the output quantities. Our strategy centers on exploiting information neglected by current techniques, which collect moments in each cell without regard to one another, values in neighboring cells, nor their evolution in time. Unlike many previous acceleration techniques that modify the method itself, the techniques examined in this work strictly post-process so they may be applied to any DSMC code without affecting its fidelity or generality. Many potential methods are drawn from successful applications in a diverse range of areas, from ultrasound imaging to financial market analysis. The most promising methods exploit relationships between variables in space, which always exist in DSMC due to the absence of shocks. Disparate techniques were shown to produce similar error reductions, suggesting that the results shown in this report may be typical of what is possible using these methods. Sample count reduction factors of approximately three to five were found to be typical, although factors exceeding ten were shown on some variables under some techniques.

  7. Validation of SCALE 4. 0 -- CSAS25 module and the 27-group ENDF/B-IV cross-section library for low-enriched uranium systems

    SciTech Connect (OSTI)

    Jordan, W.C.

    1993-02-01T23:59:59.000Z

    A version of KENO V.a and the 27-group library in SCALE-4.0 were validated for use in evaluating the nuclear criticality safety of low-enriched uranium systems. A total of 59 critical systems were analyzed. A statistical analysis of the results was performed, and subcritical acceptanced criteria are established.

  8. Validation of SCALE 4.0 -- CSAS25 module and the 27-group ENDF/B-IV cross-section library for low-enriched uranium systems

    SciTech Connect (OSTI)

    Jordan, W.C.

    1993-02-01T23:59:59.000Z

    A version of KENO V.a and the 27-group library in SCALE-4.0 were validated for use in evaluating the nuclear criticality safety of low-enriched uranium systems. A total of 59 critical systems were analyzed. A statistical analysis of the results was performed, and subcritical acceptanced criteria are established.

  9. I.K. Konstantopoulos and P.J. Antsaklis, "Eigenstructure Assignment in Reconfigurable Control Systems," Technical Report of the ISIS Group, ISIS-96-001, Dept. of Electrical Engr, Univ of Notre

    E-Print Network [OSTI]

    Antsaklis, Panos

    Systems," Technical Report of the ISIS Group, ISIS-96-001, Dept. of Electrical Engr, Univ of Notre Dame Control Systems," Technical Report of the ISIS Group, ISIS-96-001, Dept. of Electrical Engr, Univ of Notre in Reconfigurable Control Systems," Technical Report of the ISIS Group, ISIS-96-001, Dept. of Electrical Engr, Univ

  10. P. J. Antsaklis, M. D. Lemmon and J. A. Stiver, "Learning to be Autonomous: Intelligent Supervisory Control," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS-

    E-Print Network [OSTI]

    Antsaklis, Panos

    Control," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS," Technical Report of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS- 93 of the ISIS (Interdisciplinary Studies of Intelligent Systems) Group, No. ISIS- 93-003, Univ of Notre Dame

  11. I.K. Konstantopoulos and P.J. Antsaklis, "An Optimization Strategy for Reconfigurable Control Systems," Technical Report of the ISIS Group, ISIS-95-006, Dept. of Electrical Engr, Univ of Notre Dame,

    E-Print Network [OSTI]

    Antsaklis, Panos

    Systems," Technical Report of the ISIS Group, ISIS-95-006, Dept. of Electrical Engr, Univ of Notre Dame Control Systems," Technical Report of the ISIS Group, ISIS-95-006, Dept. of Electrical Engr, Univ of Notre for Reconfigurable Control Systems," Technical Report of the ISIS Group, ISIS-95-006, Dept. of Electrical Engr, Univ

  12. Hydrogen Technologies Group

    SciTech Connect (OSTI)

    Not Available

    2008-03-01T23:59:59.000Z

    The Hydrogen Technologies Group at the National Renewable Energy Laboratory advances the Hydrogen Technologies and Systems Center's mission by researching a variety of hydrogen technologies.

  13. Perturbations for transient acceleration

    SciTech Connect (OSTI)

    Vargas, Cristofher Zuñiga; Zimdahl, Winfried [Universidade Federal do Espírito Santo, Departamento de Física, Av. Fernando Ferrari, 514, Campus de Goiabeiras, CEP 29075-910, Vitória, Espírito Santo (Brazil); Hipólito-Ricaldi, Wiliam S., E-mail: win_unac@hotmail.com, E-mail: hipolito@ceunes.ufes.br, E-mail: winfried.zimdahl@pq.cnpq.br [Universidade Federal do Espírito Santo, Departamento de Ciências Naturais, Grupo de Física Teórica, Rodovia BR 101 Norte, km 60, Campus de São Mateus, CEP 29932-540, São Mateus, Espírito Santo (Brazil)

    2012-04-01T23:59:59.000Z

    According to the standard ?CDM model, the accelerated expansion of the Universe will go on forever. Motivated by recent observational results, we explore the possibility of a finite phase of acceleration which asymptotically approaches another period of decelerated expansion. Extending an earlier study on a corresponding homogeneous and isotropic dynamics, in which interactions between dark matter and dark energy are crucial, the present paper also investigates the dynamics of the matter perturbations both on the Newtonian and General Relativistic (GR) levels and quantifies the potential relevance of perturbations of the dark-energy component. In the background, the model is tested against the Supernova type Ia (SNIa) data of the Constitution set and on the perturbative level against growth rate data, among them those of the WiggleZ survey, and the data of the 2dFGRS project. Our results indicate that a transient phase of accelerated expansion is not excluded by current observations.

  14. HIGH GRADIENT INDUCTION ACCELERATOR

    SciTech Connect (OSTI)

    Caporaso, G J; Sampayan, S; Chen, Y; Blackfield, D; Harris, J; Hawkins, S; Holmes, C; Krogh, M; Nelson, S; Nunnally, W; Paul, A; Poole, B; Rhodes, M; Sanders, D; Selenes, K; Sullivan, J; Wang, L; Watson, J

    2007-06-21T23:59:59.000Z

    A new type of compact induction accelerator is under development at the Lawrence Livermore National Laboratory that promises to increase the average accelerating gradient by at least an order of magnitude over that of existing induction machines. The machine is based on the use of high gradient vacuum insulators, advanced dielectric materials and switches and is stimulated by the desire for compact flash x-ray radiography sources. Research describing an extreme variant of this technology aimed at proton therapy for cancer will be described. Progress in applying this technology to several applications will be reviewed.

  15. Final Report for U.S. DOE GRANT No. DEFG02-96ER41015 November 1, 2010 - April 30, 2013 entitled HIGH ENERGY ACCELERATOR AND COLLIDING BEAM USER GROUP at the UNIVERSITY of MARYLAND

    SciTech Connect (OSTI)

    Hadley, Nicholas [University of Maryland College Park; Jawahery, Abolhassan [University of Maryland College Park; Eno, Sarah C [University of Maryland College Park; Skuja, Andris [University of Maryland College Park; Baden, Andrew [University of Maryland College Park; Roberts, Douglas [University of Maryland College Park

    2013-07-26T23:59:59.000Z

    We have #12;finished the third year of a three year grant cycle with the U.S. Department of Energy for which we were given a #12;five month extension (U.S. D.O.E. Grant No. DEFG02-96ER41015). This document is the fi#12;nal report for this grant and covers the period from November 1, 2010 to April 30, 2013. The Maryland program is administered as a single task with Professor Nicholas Hadley as Principal Investigator. The Maryland experimental HEP group is focused on two major research areas. We are members of the CMS experiment at the LHC at CERN working on the physics of the Energy Frontier. We are also analyzing the data from the Babar experiment at SLAC while doing design work and R&D towards a Super B experiment as part of the Intensity Frontier. We have recently joined the LHCb experiment at CERN. We concluded our activities on the D#31; experiment at Fermilab in 2009.

  16. Accelerator Driven Nuclear Energy: The Thorium Option

    SciTech Connect (OSTI)

    Raja, Rajendran

    2009-03-18T23:59:59.000Z

    Conventional nuclear reactors use enriched Uranium as fuel and produce nuclear waste which needs to be stored away for over 10,000 years. At the current rate of use, existing sources of Uranium will last for 50-100 years. We describe a solution to the problem that uses particle accelerators to produce fast neutrons that can be used to burn existing nuclear waste and produce energy. Such systems, initially proposed by Carlo Rubbia and collaborators in the 1990's, are being seriously considered by many countries as a possible solution to the green energy problem. Accelerator driven reactors operate in a sub-critical regime and, thus, are safer and can obtain energy from plentiful elements such as Thorium-232 and Uranium-238. What is missing is the high intensity (10MW) accelerator that produces 1 GeV protons. We will describe scenarios which if implemented will make such systems a reality.

  17. Accelerator Driven Nuclear Energy - The Thorium Option

    SciTech Connect (OSTI)

    Rajendran Raja

    2009-03-18T23:59:59.000Z

    Conventional nuclear reactors use enriched Uranium as fuel and produce nuclear waste which needs to be stored away for over 10,000 years.   At the current rate of use, existing sources of Uranium will last for 50-100 years.  We describe a solution to the problem that uses particle accelerators to produce fast neutrons that can be used to burn existing nuclear waste and produce energy.  Such systems, initially proposed by Carlo Rubbia and collaborators in the 1990's, are being seriously considered by many countries as a possible solution to the green energy problem.  Accelerator driven reactors operate in a sub-critical regime and, thus, are safer and can obtain energy from plentiful elements such as Thorium-232 and Uranium-238. What is missing is the high intensity (10MW) accelerator that produces 1 GeV protons. We will describe scenarios which if implemented will make such systems a reality.  

  18. Accelerator Driven Nuclear Energy - The Thorium Option

    ScienceCinema (OSTI)

    Rajendran Raja

    2010-01-08T23:59:59.000Z

    Conventional nuclear reactors use enriched Uranium as fuel and produce nuclear waste which needs to be stored away for over 10,000 years.   At the current rate of use, existing sources of Uranium will last for 50-100 years.  We describe a solution to the problem that uses particle accelerators to produce fast neutrons that can be used to burn existing nuclear waste and produce energy.  Such systems, initially proposed by Carlo Rubbia and collaborators in the 1990's, are being seriously considered by many countries as a possible solution to the green energy problem.  Accelerator driven reactors operate in a sub-critical regime and, thus, are safer and can obtain energy from plentiful elements such as Thorium-232 and Uranium-238. What is missing is the high intensity (10MW) accelerator that produces 1 GeV protons. We will describe scenarios which if implemented will make such systems a reality.  

  19. Grouped exposed metal heaters

    DOE Patents [OSTI]

    Vinegar, Harold J. (Bellaire, TX); Coit, William George (Bellaire, TX); Griffin, Peter Terry (Brixham, GB); Hamilton, Paul Taylor (Houston, TX); Hsu, Chia-Fu (Granada Hills, CA); Mason, Stanley Leroy (Allen, TX); Samuel, Allan James (Kular Lumpar, MY); Watkins, Ronnie Wade (Cypress, TX)

    2010-11-09T23:59:59.000Z

    A system for treating a hydrocarbon containing formation is described. The system includes two or more groups of elongated heaters. The group includes two or more heaters placed in two or more openings in the formation. The heaters in the group are electrically coupled below the surface of the formation. The openings include at least partially uncased wellbores in a hydrocarbon layer of the formation. The groups are electrically configured such that current flow through the formation between at least two groups is inhibited. The heaters are configured to provide heat to the formation.

  20. Grouped exposed metal heaters

    DOE Patents [OSTI]

    Vinegar, Harold J. (Bellaire, TX); Coit, William George (Bellaire, TX); Griffin, Peter Terry (Brixham, GB); Hamilton, Paul Taylor (Houston, TX); Hsu, Chia-Fu (Granada Hills, CA); Mason, Stanley Leroy (Allen, TX); Samuel, Allan James (Kular Lumpar, ML); Watkins, Ronnie Wade (Cypress, TX)

    2012-07-31T23:59:59.000Z

    A system for treating a hydrocarbon containing formation is described. The system includes two or more groups of elongated heaters. The group includes two or more heaters placed in two or more openings in the formation. The heaters in the group are electrically coupled below the surface of the formation. The openings include at least partially uncased wellbores in a hydrocarbon layer of the formation. The groups are electrically configured such that current flow through the formation between at least two groups is inhibited. The heaters are configured to provide heat to the formation.

  1. Advanced Accelerator Concepts Final Report

    SciTech Connect (OSTI)

    Wurtele, Jonathan S.

    2014-05-13T23:59:59.000Z

    A major focus of research supported by this Grant has been on the ALPHA antihydrogen trap. We first trapped antihydrogen in 2010 and soon thereafter demonstrated trapping for 1000s. We now have observed resonant quantum interactions with antihydrogen. These papers in Nature and Nature Physics report the major milestones in anti-atom trapping. The success was only achieved through careful work that advanced our understanding of collective dynamics in charged particle systems, the development of new cooling and diagnostics, and in- novation in understanding how to make physics measurements with small numbers of anti-atoms. This research included evaporative cooling, autoresonant excitation of longitudinal motion, and centrifugal separation. Antihydrogen trapping by ALPHA is progressing towards the point when a important theories believed by most to hold for all physical systems, such as CPT (Charge-Parity-Time) invariance and the Weak Equivalence Principle (matter and antimatter behaving the same way under the influence of gravity) can be directly tested in a new regime. One motivation for this test is that most accepted theories of the Big Bang predict that we should observe equal amounts of matter and antimatter. However astrophysicists have found very little antimatter in the universe. Our experiment will, if successful over the next seven years, provide a new test of these ideas. Many earlier detailed and beautiful tests have been made, but the trapping of neutral antimatter allows us to explore the possibility of direct, model-independent tests. Successful cooling of the anti atoms, careful limits on systematics and increased trapping rates, all planned for our follow-up experiment (ALPHA-II) will reach unrivaled precision. CPT invariance implies that the spectra of hydrogen and antihydrogen should be identical. Spectra can be measured in principle with great precision, and any di#11;erences we might observe would revolutionize fundamental physics. This is the physics motivation for our experiment, one that requires only a few dozen researchers but must effectively integrate plasma, accelerator, atomic, and fundamental physics, as well as combine numerous technologies in the control, manipulation, and measurement of neutral and non-neutral particles. The ELENA ring (to which we hope to contribute, should funding be provided) is expect, when completed, to significantly enhance the performance of antihydrogen trapping by increasing by a factor of 100 the number of antiprotons that can be successfully trapped and cooled. ELENA operation is scheduled to commence in 2017. In collaboration with LBNL scientists, we proposed a frictional cooling scheme. This is an alternative cooling method to that used by ELENA. It is less complicated, experimentally unproven, and produces a lower yield of cold antiprotons. Students and postdoctoral researchers work on the trapping, cooling, transport, and nonlinear dynamics of antiprotons bunches that are provided by the AD to ALPHA; they contribute to the operation of the experiment, to software development, and to the design and operation of experiments. Students are expected to spend at summers at CERN while taking courses; after completion of courses they typically reside at CERN for most of the half-year run. The Antiproton Decelerator [AD] at CERN, along with its experiments, is the only facility in the world where antiprotons can be trapped and cooled and combined with positrons to form cold antihydrogen, with the ultimate goal of studying CPT violation and, subsequently, gravitational interactions of antimatter. Beyond the ALPHA experiment, the group worked on beam physics problems including limits on the average current in a time-dependent period cathode and new methods to create longitudinally coherent high repetition rate soft x-ray sources and wide bandwidth mode locked x-ray lasers. We completed a detailed study of quantum mechanical effects in the transit time cooling of muons.

  2. A GPU-INSPIRED SOFT PROCESSOR FOR HIGH-THROUGHPUT ACCELERATION

    E-Print Network [OSTI]

    Steffan, J. Gregory

    Methodology 35 6.1 System Simulation . . . . . . . A GPU-INSPIRED SOFT PROCESSOR FOR HIGH-THROUGHPUT ACCELERATION by Jeffrey Richard Code Kingyens Code Kingyens #12;Abstract A GPU-Inspired Soft Processor for High-Throughput Acceleration Jeffrey

  3. Vacuum Insulator Development for the Dielectric Wall Accelerator

    SciTech Connect (OSTI)

    Harris, J R; Blackfield, D; Caporaso, G J; Chen, Y; Hawkins, S; Kendig, M; Poole, B; Sanders, D M; Krogh, M; Managan, J E

    2008-03-17T23:59:59.000Z

    At Lawrence Livermore National Laboratory, we are developing a new type of accelerator, known as a Dielectric Wall Accelerator, in which compact pulse forming lines directly apply an accelerating field to the beam through an insulating vacuum boundary. The electrical strength of this insulator may define the maximum gradient achievable in these machines. To increase the system gradient, we are using 'High Gradient Insulators' composed of alternating layers of dielectric and metal for the vacuum insulator. In this paper, we present our recent results from experiment and simulation, including the first test of a High Gradient Insulator in a functioning Dielectric Wall Accelerator cell.

  4. Fermilab Steering Group Report

    SciTech Connect (OSTI)

    Beier, Eugene; /Pennsylvania U.; Butler, Joel; /Fermilab; Dawson, Sally; /Brookhaven; Edwards, Helen; /Fermilab; Himel, Thomas; /SLAC; Holmes, Stephen; /Fermilab; Kim, Young-Kee; /Fermilab /Chicago U.; Lankford, Andrew; /UC, Irvine; McGinnis, David; /Fermilab; Nagaitsev, Sergei; /Fermilab; Raubenheimer, Tor; /SLAC /Fermilab

    2007-01-01T23:59:59.000Z

    The Fermilab Steering Group has developed a plan to keep U.S. accelerator-based particle physics on the pathway to discovery, both at the Terascale with the LHC and the ILC and in the domain of neutrinos and precision physics with a high-intensity accelerator. The plan puts discovering Terascale physics with the LHC and the ILC as Fermilab's highest priority. While supporting ILC development, the plan creates opportunities for exciting science at the intensity frontier. If the ILC remains near the Global Design Effort's technically driven timeline, Fermilab would continue neutrino science with the NOVA experiment, using the NuMI (Neutrinos at the Main Injector) proton plan, scheduled to begin operating in 2011. If ILC construction must wait somewhat longer, Fermilab's plan proposes SNuMI, an upgrade of NuMI to create a more powerful neutrino beam. If the ILC start is postponed significantly, a central feature of the proposed Fermilab plan calls for building an intense proton facility, Project X, consisting of a linear accelerator with the currently planned characteristics of the ILC combined with Fermilab's existing Recycler Ring and the Main Injector accelerator. The major component of Project X is the linac. Cryomodules, radio-frequency distribution, cryogenics and instrumentation for the linac are the same as or similar to those used in the ILC at a scale of about one percent of a full ILC linac. Project X's intense proton beams would open a path to discovery in neutrino science and in precision physics with charged leptons and quarks. World-leading experiments would allow physicists to address key questions of the Quantum Universe: How did the universe come to be? Are there undiscovered principles of nature: new symmetries, new physical laws? Do all the particles and forces become one? What happened to the antimatter? Building Project X's ILC-like linac would offer substantial support for ILC development by accelerating the industrialization of ILC components in the U.S. and creating an engineering opportunity for ILC cost reductions. It offers an early and tangible application for ILC R&D in superconducting technology, attracting participation from accelerator scientists worldwide and driving forward the technology for still higher-energy accelerators of the future, such as a muon collider. To prepare for a future decision, the Fermilab Steering Group recommends that the laboratory seek R&D support for Project X, in order to produce an overall design of Project X and to spur the R&D and industrialization of ILC linac components needed for Project X. Advice from the High Energy Physics Advisory Panel will guide any future decision to upgrade the Fermilab accelerator complex, taking into account developments affecting the ILC schedule and the continuing evaluation of scientific priorities for U.S. particle physics. Fermilab should also work toward increased resources for longer-term future accelerators such as a muon collider, aiming at higher energies than the ILC would provide.

  5. Beam-driven acceleration in ultra-dense plasma media

    SciTech Connect (OSTI)

    Shin, Young-Min [Fermi National Accelerator Laboratory, Batavia, IL (United States)

    2014-09-12T23:59:59.000Z

    Accelerating parameters of beam-driven wakefield acceleration in an extremely dense plasma column has been analyzed with the dynamic framed particle-in-cell plasma simulator, and compared with analytic calculations. In the model, a witness beam undergoes a TeV/m scale alternating potential gradient excited by a micro-bunched drive beam in a 1025 m-3 and 1.6 x 1028 m-3 plasma column. The acceleration gradient, energy gain, and transformer ratio have been extensively studied in quasi-linear, linear-, and blowout-regimes. The simulation analysis indicated that in the beam-driven acceleration system a hollow plasma channel offers 20 % higher acceleration gradient by enlarging the channel radius (r) from 0.2 Ap to 0.6 .Ap in a blowout regime. This paper suggests a feasibility of TeV/m scale acceleration with a hollow crystalline structure (e.g. nanotubes) of high electron plasma density.

  6. Beam-driven acceleration in ultra-dense plasma media

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Shin, Young-Min [Fermi National Accelerator Laboratory, Batavia, IL (United States)

    2014-09-15T23:59:59.000Z

    Accelerating parameters of beam-driven wakefield acceleration in an extremely dense plasma column has been analyzed with the dynamic framed particle-in-cell plasma simulator, and compared with analytic calculations. In the model, a witness beam undergoes a TeV/m scale alternating potential gradient excited by a micro-bunched drive beam in a 1025 m-3 and 1.6 x 1028 m-3 plasma column. The acceleration gradient, energy gain, and transformer ratio have been extensively studied in quasi-linear, linear-, and blowout-regimes. The simulation analysis indicated that in the beam-driven acceleration system a hollow plasma channel offers 20 % higher acceleration gradient by enlarging the channel radius (r) from 0.2 ?p to 0.6 ?p in a blowout regime. This paper suggests a feasibility of TeV/m scale acceleration with a hollow crystalline structure (e.g. nanotubes) of high electron plasma density.

  7. Beam-driven acceleration in ultra-dense plasma media

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Shin, Young-Min

    2014-09-15T23:59:59.000Z

    Accelerating parameters of beam-driven wakefield acceleration in an extremely dense plasma column has been analyzed with the dynamic framed particle-in-cell plasma simulator, and compared with analytic calculations. In the model, a witness beam undergoes a TeV/m scale alternating potential gradient excited by a micro-bunched drive beam in a 1025 m-3 and 1.6 x 1028 m-3 plasma column. The acceleration gradient, energy gain, and transformer ratio have been extensively studied in quasi-linear, linear-, and blowout-regimes. The simulation analysis indicated that in the beam-driven acceleration system a hollow plasma channel offers 20 % higher acceleration gradient by enlarging the channel radius (r)more »from 0.2 ?p to 0.6 ?p in a blowout regime. This paper suggests a feasibility of TeV/m scale acceleration with a hollow crystalline structure (e.g. nanotubes) of high electron plasma density.« less

  8. Deuterium accelerator experiments for APT.

    SciTech Connect (OSTI)

    Causey, Rion A. (Sandia National Laboratories, Livermore, CA); Hertz, Kristin L. (Sandia National Laboratories, Livermore, CA); Cowgill, Donald F. (Sandia National Laboratories, Livermore, CA)

    2005-08-01T23:59:59.000Z

    Sandia National Laboratories in California initiated an experimental program to determine whether tritium retention in the tube walls and permeation through the tubes into the surrounding coolant water would be a problem for the Accelerator Production of Tritium (APT), and to find ways to mitigate the problem, if it existed. Significant holdup in the tube walls would limit the ability of APT to meet its production goals, and high levels of permeation would require a costly cleanup system for the cooling water. To simulate tritium implantation, a 200 keV accelerator was used to implant deuterium into Al 6061-T and SS3 16L samples at temperatures and particle fluxes appropriate for APT, for times varying between one week and five months. The implanted samples were characterized to determine the deuterium retention and Permeation. During the implantation, the D(d,p)T nuclear reaction was used to monitor the build-up of deuterium in the implant region of the samples. These experiments increased in sophistication, from mono-energetic deuteron implants to multi-energetic deuteron and proton implants, to more accurately reproduce the conditions expected in APT. Micron-thick copper, nickel, and anodized aluminum coatings were applied to the front surface of the samples (inside of the APT walls) in an attempt to lower retention and permeation. The reduction in both retention and permeation produced by the nickel coatings, and the ability to apply them to the inside of the APT tubes, indicate that both nickel-coated Al 6061-T6 and nickel-coated SS3 16L tubes would be effective for use in APT. The results of this work were submitted to the Accelerator Production of Tritium project in document number TPO-E29-Z-TNS-X-00050, APT-MP-01-17.

  9. Variable-energy drift-tube linear accelerator

    DOE Patents [OSTI]

    Swenson, Donald A. (Los Alamos, NM); Boyd, Jr., Thomas J. (Los Alamos, NM); Potter, James M. (Los Alamos, NM); Stovall, James E. (Los Alamos, NM)

    1984-01-01T23:59:59.000Z

    A linear accelerator system includes a plurality of post-coupled drift-tubes wherein each post coupler is bistably positionable to either of two positions which result in different field distributions. With binary control over a plurality of post couplers, a significant accumlative effect in the resulting field distribution is achieved yielding a variable-energy drift-tube linear accelerator.

  10. Simulations of Direct Ion Acceleration with Beating Electrostatic Waves

    E-Print Network [OSTI]

    Choueiri, Edgar

    . Gardineer, IV , Benjamin Jorns , and Edgar Y. Choueiri Electric Propulsion and Plasma Dynamics Laboratory Wave Thruster (BWT) ­ an electrodeless electric propulsion concept based on direct ion acceleration. The ultimate goal is for this acceleration mechanism to form the basis of a new plasma propulsion system called

  11. Drift tube suspension for high intensity linear accelerators

    DOE Patents [OSTI]

    Liska, D.J.; Schamaun, R.G.; Clark, D.C.; Potter, R.C.; Frank, J.A.

    1980-03-11T23:59:59.000Z

    The disclosure relates to a drift tube suspension for high intensity linear accelerators. The system comprises a series of box-sections girders independently adjustably mounted on a linear accelerator. A plurality of drift tube holding stems are individually adjustably mounted on each girder.

  12. Insights from US ITER: Strategies for Accelerating

    E-Print Network [OSTI]

    Insights from US ITER: Strategies for Accelerating Fusion Energy as a Project Ned Sauthoff US ITER Project Manager SOFE Town Hall Meeting | June 27, 2011 #12;1. Treat fusion energy as a project, rather than a program. Mission: ·Rapid materials and fusion systems development, leading

  13. TOPICS IN THE PHYSICS OF PARTICLE ACCELERATORS

    E-Print Network [OSTI]

    Sessler, A.M.

    2008-01-01T23:59:59.000Z

    their whole lives to accelerator physics. As high energysome appreciation of accelerator physics. We cannot, nor dolectures on basic accelerator physics; then you will hear

  14. Optics elements for modeling electrostatic lenses and accelerator components II. Acceleration columns

    SciTech Connect (OSTI)

    Gillespie, G.H., Brown, T.A.

    1998-05-01T23:59:59.000Z

    A set of optical models for a variety of electrostatic lenses and accelerator columns has been developed for the computer code TRACE 3-D. TRACE 3-D is an envelope (matrix) code including space charge that is often used to model bunched beams in magnetic transport systems and radiofrequency (RF) accelerators when the effects of beam current may be important. Several new matrix models have been developed that allow the code to be used for modeling beam lines and accelerators with electrostatic components. The new models include a number of options for: (1) einzel lenses, (2) accelerator columns, (3) electrostatic deflectors (prisms), and (4) an electrostatic quadrupole. A prescription for setting up the initial beam appropriate to modeling 2-D (continuous) beams has also been developed. The new models for (2) are described in this paper, selected comparisons with other calculations are presented, and a beamline application is summarized.

  15. Accelerator Design Concept for Future Neutrino Facilities

    SciTech Connect (OSTI)

    ISS Accelerator Working Group; Zisman, Michael S; Berg, J. S.; Blondel, A.; Brooks, S.; Campagne, J.-E.; Caspar, D.; Cevata, C.; Chimenti, P.; Cobb, J.; Dracos, M.; Edgecock, R.; Efthymiopoulos, I.; Fabich, A.; Fernow, R.; Filthaut, F.; Gallardo, J.; Garoby, R.; Geer, S.; Gerigk, F.; Hanson, G.; Johnson, R.; Johnstone, C.; Kaplan, D.; Keil, E.; Kirk, H.; Klier, A.; Kurup, A.; Lettry, J.; Long, K.; Machida, S.; McDonald, K.; Meot, F.; Mori, Y.; Neuffer, D.; Palladino, V.; Palmer, R.; Paul, K.; Poklonskiy, A.; Popovic, M.; Prior, C.; Rees, G.; Rossi, C.; Rovelli, T.; Sandstrom, R.; Sevior, R.; Sievers, P.; Simos, N.; Torun, Y.; Vretenar, M.; Yoshimura, K.; Zisman, Michael S

    2008-02-03T23:59:59.000Z

    This document summarizes the findings of the Accelerator Working Group (AWG) of the International Scoping Study (ISS) of a Future Neutrino Factory and Superbeam Facility. The work of the group took place at three plenary meetings along with three workshops, and an oral summary report was presented at the NuFact06 workshop held at UC-Irvine in August, 2006. The goal was to reach consensus on a baseline design for a Neutrino Factory complex. One aspect of this endeavor was to examine critically the advantages and disadvantages of the various Neutrino Factory schemes that have been proposed in recent years.

  16. Workshop on acceleration of polarized protons: summary report

    SciTech Connect (OSTI)

    Lee, Y.Y.; Terwilliger, K.M.

    1982-01-01T23:59:59.000Z

    The workshop sessions concentrated on polarized protons in circular accelerators and storage rings. Topics such as polarized electrons were discussed only when the subject was relevant to proton phenomena. Of major interest was the possible applicability of the new idea of spin matching for crossing depolarizing resonances. On the experimental side, some remarkable new data were presented by the SATURNE II Group. They have successfully crossed both intrinsic and imperfection depolarizing resonances by the spin flip method with minimal depolarization-the first group to do so. They also obtained some results which apparently cannot be explained with our present understanding of spin phenomena. The workshop concluded that more experimental measurements are needed to understand the physics and that such studies would be very important for the future acceleration of polarized protons at KEK and the AGS. The workshop included status reports from the four laboratories which have programs of polarized particle acceleration--or approved projects to accelerate polarized protons.

  17. Developments on the SCADA of CERN Accelerators Vacuum

    E-Print Network [OSTI]

    Antoniotti, F; Boccioli, M; Gomes, P; Pereira, H; Kopylov, L; Mikheev, M; Merker, S

    2014-01-01T23:59:59.000Z

    During the first 3 years of LHC operation, the priority for the SCADA (Supervisory Control And Data Acquisition) of vacuum controls was to attend to user requests, and to improve its ergonomics and efficiency: access & presentation of information simplified and normalized; coherent functionalities & menus across all accelerators; automatic scripts instead of fastidious manual actions; enhanced tools for data analysis and for maintenance interventions. Several decades of cumulative developments, based on heterogeneous technologies and architectures, have been asking for a homogenization effort. The first LHC Long Shutdown (LS1) provides the opportunity to further standardize the vacuum controls systems [1], around Siemens-S7 PLCs (Programmable Logic Controllers) and PVSS SCADA. Meanwhile, exchanges with other Groups at CERN and outside Institutes have been promoted: to follow the global update policy for software libraries; to discuss philosophies and development details; and to accomplish common pro...

  18. Particle Acceleration at Relativistic Shocks

    E-Print Network [OSTI]

    Yves A. Gallant

    2002-01-15T23:59:59.000Z

    I review the current status of Fermi acceleration theory at relativistic shocks. I first discuss the relativistic shock jump conditions, then describe the non-relativistic Fermi mechanism and the differences introduced by relativistic flows. I present numerical calculations of the accelerated particle spectrum, and examine the maximum energy attainable by this process. I briefly consider the minimum energy for Fermi acceleration, and a possible electron pre-acceleration mechanism.

  19. Acceleration of inertial particles in wall bounded flows: DNS and LES with stochastic modelling of the subgrid acceleration

    E-Print Network [OSTI]

    Boyer, Edmond

    environmental systems, from sediment transport to atmospheric dispersion of pollutants or solid depositionAcceleration of inertial particles in wall bounded flows: DNS and LES with stochastic modelling and LES with stochastic modelling of the subgrid acceleration R´emi Zamansky, Ivana Vinkovic, Mikhael

  20. Group X

    SciTech Connect (OSTI)

    Fields, Susannah

    2007-08-16T23:59:59.000Z

    This project is currently under contract for research through the Department of Homeland Security until 2011. The group I was responsible for studying has to remain confidential so as not to affect the current project. All dates, reference links and authors, and other distinguishing characteristics of the original group have been removed from this report. All references to the name of this group or the individual splinter groups has been changed to 'Group X'. I have been collecting texts from a variety of sources intended for the use of recruiting and radicalizing members for Group X splinter groups for the purpose of researching the motivation and intent of leaders of those groups and their influence over the likelihood of group radicalization. This work included visiting many Group X websites to find information on splinter group leaders and finding their statements to new and old members. This proved difficult because the splinter groups of Group X are united in beliefs, but differ in public opinion. They are eager to tear each other down, prove their superiority, and yet remain anonymous. After a few weeks of intense searching, a list of eight recruiting texts and eight radicalizing texts from a variety of Group X leaders were compiled.

  1. Radiation from Accelerated Branes

    E-Print Network [OSTI]

    Mohab Abou-Zeid; Miguel S. Costa

    2000-01-29T23:59:59.000Z

    The radiation emitted by accelerated fundamental strings and D-branes is studied within the linear approximation to the supergravity limit of string theory. We show that scalar, gauge field and gravitational radiation is generically emitted by such branes. In the case where an external scalar field accelerates the branes, we derive a Larmor-type formula for the emitted scalar radiation and study the angular distribution of the outgoing energy flux. The classical radii of the branes are calculated by means of the corresponding Thompson scattering cross sections. Within the linear approximation, the interaction of the external scalar field with the velocity fields of the branes gives a contribution to the observed gauge field and gravitational radiation.

  2. Adaptive control for accelerators

    DOE Patents [OSTI]

    Eaton, Lawrie E. (Los Alamos, NM); Jachim, Stephen P. (Los Alamos, NM); Natter, Eckard F. (Santa Fe, NM)

    1991-01-01T23:59:59.000Z

    An adaptive feedforward control loop is provided to stabilize accelerator beam loading of the radio frequency field in an accelerator cavity during successive pulses of the beam into the cavity. A digital signal processor enables an adaptive algorithm to generate a feedforward error correcting signal functionally determined by the feedback error obtained by a beam pulse loading the cavity after the previous correcting signal was applied to the cavity. Each cavity feedforward correcting signal is successively stored in the digital processor and modified by the feedback error resulting from its application to generate the next feedforward error correcting signal. A feedforward error correcting signal is generated by the digital processor in advance of the beam pulse to enable a composite correcting signal and the beam pulse to arrive concurrently at the cavity.

  3. Accelerator research studies

    SciTech Connect (OSTI)

    Not Available

    1993-01-01T23:59:59.000Z

    The Accelerator Research Studies program at the University of Maryland, sponsored by the Department of Energy under grant number DE-FG05-91ER40642, is currently in the second year of a three-year funding cycle. The program consists of the following three tasks: TASK A, Study of Transport and Longitudinal Compression of Intense, High-Brightness Beams,'' (P.I., M. Reiser); TASK B, Study of Collective Ion Acceleration by Intense Electron Beams and Pseudospark Produced High Brightness Electron Beams,'' (Co-P.I.'s, W.W. Destler, M. Reiser, M.J. Rhee, and C.D. Striffler); TASK C, Study of a Gyroklystron High-Power Microwave Source for Linear Colliders,'' (Co-P.I.'s, V.L. Granatstein, W. Lawson, M. Reiser, and C.D. Striffler). In this report we document the progress that has been made during the past year for each of the three tasks.

  4. This paper has been downloaded from the Building and Environmental Thermal Systems Research Group at Oklahoma State University (http://www.hvac.okstate.edu).

    E-Print Network [OSTI]

    This paper has been downloaded from the Building and Environmental Thermal Systems Research Group that is typically only the case for envelope-dominated buildings in a given location. · Reasonably constant ground thermal properties between locations for which the rule-of-thumb would be applied. The main example

  5. Accelerating QDP++ using GPUs

    E-Print Network [OSTI]

    Frank Winter

    2011-05-11T23:59:59.000Z

    Graphic Processing Units (GPUs) are getting increasingly important as target architectures in scientific High Performance Computing (HPC). NVIDIA established CUDA as a parallel computing architecture controlling and making use of the compute power of GPUs. CUDA provides sufficient support for C++ language elements to enable the Expression Template (ET) technique in the device memory domain. QDP++ is a C++ vector class library suited for quantum field theory which provides vector data types and expressions and forms the basis of the lattice QCD software suite Chroma. In this work accelerating QDP++ expression evaluation to a GPU was successfully implemented leveraging the ET technique and using Just-In-Time (JIT) compilation. The Portable Expression Template Engine (PETE) and the C API for CUDA kernel arguments were used to build the bridge between host and device memory domains. This provides the possibility to accelerate Chroma routines to a GPU which are typically not subject to special optimisation. As an application example a smearing routine was accelerated to execute on a GPU. A significant speed-up compared to normal CPU execution could be measured.

  6. Data Management Group Annual Report

    E-Print Network [OSTI]

    Toronto, University of

    Data Management Group Annual Report 2001 prepared by: Data Management Group Joint Program..............................................................................2 Text Based Data Retrieval System `drs' ..........................................................2 Internet Browser Data Retrieval System (iDRS)..............................................3 Complex Data

  7. Data Management Group Annual Report

    E-Print Network [OSTI]

    Toronto, University of

    Data Management Group Annual Report 1999 prepared by: Data Management Group Joint Program................................................................. 1 INFORMATION PROCESSING ............................................. 2 Text Based Data Retrieval System `drs' ........................ 2 Internet Browser Data Retrieval System (iDRS) ............ 3

  8. Recent Advances in Plasma Acceleration

    SciTech Connect (OSTI)

    Hogan, Mark

    2007-03-19T23:59:59.000Z

    The costs and the time scales of colliders intended to reach the energy frontier are such that it is important to explore new methods of accelerating particles to high energies. Plasma-based accelerators are particularly attractive because they are capable of producing accelerating fields that are orders of magnitude larger than those used in conventional colliders. In these accelerators a drive beam, either laser or particle, produces a plasma wave (wakefield) that accelerates charged particles. The ultimate utility of plasma accelerators will depend on sustaining ultra-high accelerating fields over a substantial length to achieve a significant energy gain. More than 42 GeV energy gain was achieved in an 85 cm long plasma wakefield accelerator driven by a 42 GeV electron drive beam in the Final Focus Test Beam (FFTB) Facility at SLAC. Most of the beam electrons lose energy to the plasma wave, but some electrons in the back of the same beam pulse are accelerated with a field of {approx}52 GV/m. This effectively doubles their energy, producing the energy gain of the 3 km long SLAC accelerator in less than a meter for a small fraction of the electrons in the injected bunch. Prospects for a drive-witness bunch configuration and high-gradient positron acceleration experiments planned for the SABER facility will be discussed.

  9. Proof-of-principle experiments of laser Wakefield acceleration

    SciTech Connect (OSTI)

    Nakajima, K.; Kawakubo, T.; Nakanishi, H. [National Lab. for Higher Energy Physics, Ibaraki (Japan)] [and others

    1994-04-01T23:59:59.000Z

    Recently there has been a great interest in laser-plasma accelerators as possible next-generation particle accelerators because of their potential for ultra high accelerating gradients and compact size compared with conventional accelerators. It is known that the laser pulse is capable of exciting a plasma wave propagating at a phase velocity close to the velocity of light by means of beating two-frequency lasers or an ultra short laser pulse. These schemes came to be known as the Beat Wave Accelerator (BWA) for beating lasers or as the Laser Wakefield Accelerator (LWFA) for a short pulse laser. In this paper, the principle of laser wakefield particle acceleration has been tested by the Nd:glass laser system providing a short pulse with a power of 10 TW and a duration of 1 ps. Electrons accelerated up to 18 MeV/c have been observed by injecting 1 MeV/c electrons emitted from a solid target by an intense laser impact. The accelerating field gradient of 30 GeV/m is inferred.

  10. Design of an electromagnetic accelerator for turbulent hydrodynamic mix studies

    SciTech Connect (OSTI)

    Susoeff, A.R.; Hawke, R.S.; Morrison, J.J.; Dimonte, G.; Remington, B.A.

    1993-12-08T23:59:59.000Z

    An electromagnetic accelerator in the form of a linear electric motor (LEM) has been designed to achieve controlled acceleration profiles of a carriage containing hydrodynamically unstable fluids for the investigation of the development of turbulent mix. The Rayleigh- Taylor instability is investigated by accelerating two dissimilar density fluids using the LEM to achieve a wide variety of acceleration and deceleration profiles. The acceleration profiles are achieved by independent control of rail and augmentation currents. A variety of acceleration-time profiles are possible including: (1) constant, (2) impulsive and (3) shaped. The LEM and support structure are a robust design in order to withstand high loads with deflections and to mitigate operational vibration. Vibration of the carriage during acceleration could create artifacts in the data which would interfere with the intended study of the Rayleigh-Taylor instability. The design allows clear access for diagnostic techniques such as laser induced fluorescence radiography, shadowgraphs and particle imaging velocimetry. Electromagnetic modeling codes were used to optimize the rail and augmentation coil positions within the support structure framework. Results of contemporary studies for non-arcing sliding contact of solid armatures are used for the design of the driving armature and the dynamic electromagnetic braking system. A 0. 6MJ electrolytic capacitor bank is used for energy storage to drive the LEM. This report will discuss a LEM design which will accelerate masses of up to 3kg to a maximum of about 3000g{sub o}, where g{sub o} is accelerated due to gravity.

  11. High Energy Accelerator and Colliding Beam User Group

    SciTech Connect (OSTI)

    Snow, G.A.; Skuja, A.

    1992-05-01T23:59:59.000Z

    This report discusses research in the following areas: the study of e{sup +}e{sup {minus}} interactions; Hadron collider physics at Fermilab; fixed target physics and particle physics of general interest; and, the solenoidal detector collaboration at SSCL.

  12. accelerator driven transmuter: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    K. Tsujimoto; H. Takano 2 Transmutation of nuclear waste in accelerator-driven systems CERN Preprints Summary: Today more than ever energy is not only a cornerstone of human...

  13. accelerator driven subcritical: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  14. accelerator driven transmutation: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    K. Tsujimoto; H. Takano 2 Transmutation of nuclear waste in accelerator-driven systems CERN Preprints Summary: Today more than ever energy is not only a cornerstone of human...

  15. accelerator driven transmutation technologies: Topics by E-print...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    K. Tsujimoto; H. Takano 2 Transmutation of nuclear waste in accelerator-driven systems CERN Preprints Summary: Today more than ever energy is not only a cornerstone of human...

  16. Group 3: Humidity, Temperature and Voltage (Presentation)

    SciTech Connect (OSTI)

    Wohlgemuth, J.

    2013-09-01T23:59:59.000Z

    This is a summary of the work of Group 3 of the International PV QA Task Force. Group 3 is chartered to develop accelerated stress tests that can be used as comparative predictors of module lifetime versus stresses associated with humidity, temperature and voltage.

  17. Advanced Photon Source experimental beamline Safety Assessment Document: Addendum to the Advanced Photon Source Accelerator Systems Safety Assessment Document (APS-3.2.2.1.0)

    SciTech Connect (OSTI)

    NONE

    1995-01-01T23:59:59.000Z

    This Safety Assessment Document (SAD) addresses commissioning and operation of the experimental beamlines at the Advanced Photon Source (APS). Purpose of this document is to identify and describe the hazards associated with commissioning and operation of these beamlines and to document the measures taken to minimize these hazards and mitigate the hazard consequences. The potential hazards associated with the commissioning and operation of the APS facility have been identified and analyzed. Physical and administrative controls mitigate identified hazards. No hazard exists in this facility that has not been previously encountered and successfully mitigated in other accelerator and synchrotron radiation research facilities. This document is an updated version of the APS Preliminary Safety Analysis Report (PSAR). During the review of the PSAR in February 1990, the APS was determined to be a Low Hazard Facility. On June 14, 1993, the Acting Director of the Office of Energy Research endorsed the designation of the APS as a Low Hazard Facility, and this Safety Assessment Document supports that designation.

  18. PARTICLE ACCELERATION BY THE SUN ''Physics Department & Space Sciences Laboratory, University of California, Berkeley, CA

    E-Print Network [OSTI]

    California at Berkeley, University of

    PARTICLE ACCELERATION BY THE SUN R. P. Lin" ''Physics Department & Space Sciences Laboratory. INTRODUCTION The Sun is the most energetic particle accelerator in the solar system. In large solar flares energetic particle (SEP) events observed near 1 AU, but they, however, appear to be accelerated by shock

  19. This paper has been downloaded from the Building and Environmental Thermal Systems Research Group at Oklahoma State University

    E-Print Network [OSTI]

    Project RP-1356. ABSTRACT Mechanical pipe insulation systems are installed around cold cylindrical conductivity is needed for the design of insulation systems in chiller pipe applications. In this paper specimen average temperature and wall thicknesses. Corresponding uncertainties of the measurements

  20. Particle Acceleration by MHD Turbulence

    E-Print Network [OSTI]

    Jungyeon Cho; A. Lazarian

    2005-10-21T23:59:59.000Z

    Recent advances in understanding of magnetohydrodynamic (MHD) turbulence call for revisions in the picture of particle acceleration. We make use of the recently established scaling of slow and fast MHD modes in strong and weak MHD turbulence to provide a systematic study of particle acceleration in magnetic pressure (low-$\\beta$) and gaseous pressure (high-$\\beta$) dominated plasmas. We consider the acceleration by large scale compressions in both slow and fast particle diffusion limits. We compare the results with the acceleration rate that arises from resonance scattering and Transit-Time Damping (TTD). We establish that fast modes accelerate particles more efficiently than slow modes. We find that particle acceleration by pitch-angle scattering and TTD dominates acceleration by slow or fast modes when the spatial diffusion rate is small. When the rate of spatial diffusion of particles is high, we establish an enhancement of the efficiency of particle acceleration by slow and fast modes in weak turbulence. We show that highly supersonic turbulence is an efficient agent for particle acceleration. We find that even incompressible turbulence can accelerate particles on the scales comparable with the particle mean free path.

  1. Accelerators AND Beams

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office511041cloth DocumentationProducts (VAP) VAP7-0973 1 Introduction In theACME -Toggle FermilabAccelerators

  2. Institut Eurecom1 Institut Eurecom research is partially supported by its industrial members: BMW Group Research & Technology BMW Group

    E-Print Network [OSTI]

    Gesbert, David

    : BMW Group Research & Technology ­ BMW Group Company, Bouygues Telecom, Cisco Systems, France Telecom

  3. Design considerations of a power supply system for fast cycling superconducting accelerator magnets of 2 Tesla b-field generated by a conductor of 100 kA current

    SciTech Connect (OSTI)

    Hays, Steve; Piekarz, Henryk; Pfeffer, Howie; Claypool, Brad; /Fermilab

    2007-06-01T23:59:59.000Z

    Recently proposed fast cycling accelerators for proton drivers (SF-SPS, CERN and SF-MR, SF-BOOSTER, FNAL) neutrino sources require development of new magnet technology. In support of this magnet development a power supply system will need to be developed that can support the high current and high rate of power swing required by the fast cycling (1 sec rise and fall in the SF-MR, 5Hz in Booster). This paper will outline a design concept for a +/- 2000 V and 100,000 A fast ramping power supply system. This power supply design is in support of a 6.44 km magnet system at 0.020 H and 330 m 5 Hz, 0.00534 H superconducting loads. The design description will include the layout and plan for extending the present FNAL Main Injector style ramping power supply to the higher currents needed for this operation. This will also include the design for a harmonic filter and power factor corrector that will be needed to control the large power swings caused by the fast cycle time. A conceptual design for the current regulation system and control will also be outlined. The power circuit design will include the bridge, filter and transformer plan based on existing designs.

  4. Design and optimization of a multi-particle accelerator beam transport and delivery system for material irradiation in nuclear and fusion science

    E-Print Network [OSTI]

    Sordelet, Tyler Christopher

    2012-01-01T23:59:59.000Z

    A beam delivery and transport system were designed for the use in MIT Materials Test Facility (M2TF). The purpose of this beam delivery system was to design a 36 MeV Proton Cyclotron for DPA accumulation and a 100 MeV ...

  5. Chirped pulse inverse free-electron laser vacuum accelerator

    DOE Patents [OSTI]

    Hartemann, Frederic V. (Dublin, CA); Baldis, Hector A. (Pleasanton, CA); Landahl, Eric C. (Walnut Creek, CA)

    2002-01-01T23:59:59.000Z

    A chirped pulse inverse free-electron laser (IFEL) vacuum accelerator for high gradient laser acceleration in vacuum. By the use of an ultrashort (femtosecond), ultrahigh intensity chirped laser pulse both the IFEL interaction bandwidth and accelerating gradient are increased, thus yielding large gains in a compact system. In addition, the IFEL resonance condition can be maintained throughout the interaction region by using a chirped drive laser wave. In addition, diffraction can be alleviated by taking advantage of the laser optical bandwidth with negative dispersion focusing optics to produce a chromatic line focus. The combination of these features results in a compact, efficient vacuum laser accelerator which finds many applications including high energy physics, compact table-top laser accelerator for medical imaging and therapy, material science, and basic physics.

  6. Periodic relativity: deflection of light, acceleration, rotation curves

    E-Print Network [OSTI]

    Vikram H. Zaveri

    2014-12-08T23:59:59.000Z

    Vectorial analysis relating to derivation of deflection of light is presented. Curvilinear acceleration is distinguished from the Newtonian polar conic acceleration. The difference between the two is due to the curvature term. Lorentz invariant expression for acceleration is derived. A physical theory of rotation curves of galaxies based on second solution to Einstein's field equation is presented. Theory is applied to Milky Way, M31, NGC3198 and Solar system. Modified Kepler's third law yields correct orbital periods of stars in a galaxy. Deviation factor in the line element of the theory happens to be the ratio of the Newtonian gravitational acceleration to the measured acceleration of the star in the galaxy. Therefore this deviation factor can replace the MOND function.

  7. Particle Acceleration by Fast Modes in Solar Flares

    E-Print Network [OSTI]

    Huirong Yan; A. Lazarian; V. Petrosian

    2008-05-08T23:59:59.000Z

    We address the problem of particle acceleration in solar flares by fast modes which may be excited during the reconnection and undergo cascade and are subjected to damping. We extend the calculations beyond quasilinear approximation and compare the acceleration and scattering by transit time damping and gyroresonance interactions. We find that the acceleration is dominated by the so called transit time damping mechanism. We estimate the total energy transferred into particles, and show that our approach provides sufficiently accurate results We compare this rate with energy loss rate. Scattering by fast modes appears to be sufficient to prevent the protons from escaping the system during the acceleration. Confinement of electrons, on the other hand, requires the existence of plasma waves. Electrons can be accelerated to GeV energies through the process described here for solar flare conditions.

  8. Kinetic approaches to particle acceleration at cosmic ray modified shocks

    E-Print Network [OSTI]

    Elena Amato; Pasquale Blasi; Stefano Gabici

    2008-01-09T23:59:59.000Z

    Kinetic approaches provide an effective description of the process of particle acceleration at shock fronts and allow to take into account the dynamical reaction of the accelerated particles as well as the amplification of the turbulent magnetic field as due to streaming instability. The latter does in turn affect the maximum achievable momentum and thereby the acceleration process itself, in a chain of causality which is typical of non-linear systems. Here we provide a technical description of two of these kinetic approaches and show that they basically lead to the same conclusions. In particular we discuss the effects of shock modification on the spectral shape of the accelerated particles, on the maximum momentum, on the thermodynamic properties of the background fluid and on the escaping and advected fluxes of accelerated particles.

  9. Cast dielectric composite linear accelerator

    DOE Patents [OSTI]

    Sanders, David M. (Livermore, CA); Sampayan, Stephen (Manteca, CA); Slenes, Kirk (Albuquerque, NM); Stoller, H. M. (Albuquerque, NM)

    2009-11-10T23:59:59.000Z

    A linear accelerator having cast dielectric composite layers integrally formed with conductor electrodes in a solventless fabrication process, with the cast dielectric composite preferably having a nanoparticle filler in an organic polymer such as a thermosetting resin. By incorporating this cast dielectric composite the dielectric constant of critical insulating layers of the transmission lines of the accelerator are increased while simultaneously maintaining high dielectric strengths for the accelerator.

  10. Automated detection and analysis of particle beams in laser-plasma accelerator simulations

    SciTech Connect (OSTI)

    Ushizima, Daniela Mayumi; Geddes, C.G.; Cormier-Michel, E.; Bethel, E. Wes; Jacobsen, J.; Prabhat, ,; R.ubel, O.; Weber, G,; Hamann, B.

    2010-05-21T23:59:59.000Z

    Numerical simulations of laser-plasma wakefield (particle) accelerators model the acceleration of electrons trapped in plasma oscillations (wakes) left behind when an intense laser pulse propagates through the plasma. The goal of these simulations is to better understand the process involved in plasma wake generation and how electrons are trapped and accelerated by the wake. Understanding of such accelerators, and their development, offer high accelerating gradients, potentially reducing size and cost of new accelerators. One operating regime of interest is where a trapped subset of electrons loads the wake and forms an isolated group of accelerated particles with low spread in momentum and position, desirable characteristics for many applications. The electrons trapped in the wake may be accelerated to high energies, the plasma gradient in the wake reaching up to a gigaelectronvolt per centimeter. High-energy electron accelerators power intense X-ray radiation to terahertz sources, and are used in many applications including medical radiotherapy and imaging. To extract information from the simulation about the quality of the beam, a typical approach is to examine plots of the entire dataset, visually determining the adequate parameters necessary to select a subset of particles, which is then further analyzed. This procedure requires laborious examination of massive data sets over many time steps using several plots, a routine that is unfeasible for large data collections. Demand for automated analysis is growing along with the volume and size of simulations. Current 2D LWFA simulation datasets are typically between 1GB and 100GB in size, but simulations in 3D are of the order of TBs. The increase in the number of datasets and dataset sizes leads to a need for automatic routines to recognize particle patterns as particle bunches (beam of electrons) for subsequent analysis. Because of the growth in dataset size, the application of machine learning techniques for scientific data mining is increasingly considered. In plasma simulations, Bagherjeiran et al. presented a comprehensive report on applying graph-based techniques for orbit classification. They used the KAM classifier to label points and components in single and multiple orbits. Love et al. conducted an image space analysis of coherent structures in plasma simulations. They used a number of segmentation and region-growing techniques to isolate regions of interest in orbit plots. Both approaches analyzed particle accelerator data, targeting the system dynamics in terms of particle orbits. However, they did not address particle dynamics as a function of time or inspected the behavior of bunches of particles. Ruebel et al. addressed the visual analysis of massive laser wakefield acceleration (LWFA) simulation data using interactive procedures to query the data. Sophisticated visualization tools were provided to inspect the data manually. Ruebel et al. have integrated these tools to the visualization and analysis system VisIt, in addition to utilizing efficient data management based on HDF5, H5Part, and the index/query tool FastBit. In Ruebel et al. proposed automatic beam path analysis using a suite of methods to classify particles in simulation data and to analyze their temporal evolution. To enable researchers to accurately define particle beams, the method computes a set of measures based on the path of particles relative to the distance of the particles to a beam. To achieve good performance, this framework uses an analysis pipeline designed to quickly reduce the amount of data that needs to be considered in the actual path distance computation. As part of this process, region-growing methods are utilized to detect particle bunches at single time steps. Efficient data reduction is essential to enable automated analysis of large data sets as described in the next section, where data reduction methods are steered to the particular requirements of our clustering analysis. Previously, we have described the application of a set of algorithms to automate the data analys

  11. Accelerating cleanup: Paths to closure

    SciTech Connect (OSTI)

    NONE

    1998-06-01T23:59:59.000Z

    This report describes the status of Environmental Management`s (EM`s) cleanup program and a direction forward to complete achievement of the 2006 vision. Achieving the 2006 vision results in significant benefits related to accomplishing EM program objectives. As DOE sites accelerate cleanup activities, risks to public health, the environment, and worker safety and health are all reduced. Finding more efficient ways to conduct work can result in making compliance with applicable environmental requirements easier to achieve. Finally, as cleanup activities at sites are completed, the EM program can focus attention and resources on the small number of sites with more complex cleanup challenges. Chapter 1 describes the process by which this report has been developed and what it hopes to accomplish, its relationship to the EM decision-making process, and a general background of the EM mission and program. Chapter 2 describes how the site-by-site projections were constructed, and summarizes, for each of DOE`s 11 Operations/Field Offices, the projected costs and schedules for completing the cleanup mission. Chapter 3 presents summaries of the detailed cleanup projections from three of the 11 Operations/Field Offices: Rocky Flats (Colorado), Richland (Washington), and Savannah River (South Carolina). The remaining eight Operations/Field Office summaries are in Appendix E. Chapter 4 reviews the cost drivers, budgetary constraints, and performance enhancements underlying the detailed analysis of the 353 projects that comprise EM`s accelerated cleanup and closure effort. Chapter 5 describes a management system to support the EM program. Chapter 6 provides responses to the general comments received on the February draft of this document.

  12. Nuclear Physics: Archived Talks - Accelerator

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Free Electron Laser (FEL) Medical Imaging Physics Topics Campaigns Meetings Recent Talks Archived Talks Accelerator Hall A Hall B Hall C 12 GeV Upgrade Experimental Techniques...

  13. High field gradient particle accelerator

    DOE Patents [OSTI]

    Nation, J.A.; Greenwald, S.

    1989-05-30T23:59:59.000Z

    A high electric field gradient electron accelerator utilizing short duration, microwave radiation, and capable of operating at high field gradients for high energy physics applications or at reduced electric field gradients for high average current intermediate energy accelerator applications is disclosed. Particles are accelerated in a smooth bore, periodic undulating waveguide, wherein the period is so selected that the particles slip an integral number of cycles of the r.f. wave every period of the structure. This phase step of the particles produces substantially continuous acceleration in a traveling wave without transverse magnetic or other guide means for the particle. 10 figs.

  14. High field gradient particle accelerator

    DOE Patents [OSTI]

    Nation, John A. (Ithaca, NY); Greenwald, Shlomo (Haifa, IL)

    1989-01-01T23:59:59.000Z

    A high electric field gradient electron accelerator utilizing short duration, microwave radiation, and capable of operating at high field gradients for high energy physics applications or at reduced electric field gradients for high average current intermediate energy accelerator applications. Particles are accelerated in a smooth bore, periodic undulating waveguide, wherein the period is so selected that the particles slip an integral number of cycles of the r.f. wave every period of the structure. This phase step of the particles produces substantially continuous acceleration in a traveling wave without transverse magnetic or other guide means for the particle.

  15. Lab Breakthrough: Fermilab Accelerator Technology

    Broader source: Energy.gov [DOE]

    Fermilab scientists developed techniques to retrofit some of the 30,000 particle accelerators in use around the world to make them more efficient and powerful.

  16. COMPASS, the COMmunity Petascale project for Accelerator Science and Simulation, a board computational accelerator physics initiative

    E-Print Network [OSTI]

    Cary, J.R.

    2008-01-01T23:59:59.000Z

    a broad computational accelerator physics initiative † J Rbroad computational accelerator physics initiative J R Caryand future to the accelerator physics community of the

  17. This paper has been downloaded from the Building and Environmental Thermal Systems Research Group at Oklahoma State University

    E-Print Network [OSTI]

    for Residential Ground Source Heat Pump Systems In the United States. ASHRAE Transactions. 118;©2012 ASHRAE 1039 ABSTRACT Foundation heat exchangers (FHXs) used in residential ground source heat pump heat pump (GSHP) systems are frequently used in residential, commercial, and heating and cooling

  18. This paper has been downloaded from the Building and Environmental Thermal Systems Research Group at Oklahoma State University

    E-Print Network [OSTI]

    used in outdoor evaporator coils of air-source heat pump systems. Despite their potential for heat-effective performance of air condition- ing, refrigeration, and heat pump systems. The benefits of microchannel heat measured during actual frosting operating conditions, and relations with heat transfer rates, air

  19. This paper has been downloaded from the Building and Environmental Thermal Systems Research Group at Oklahoma State University

    E-Print Network [OSTI]

    not describe well the energy performance of air-source heat pump systems operating in frosting conditions. Heat and Environmental Issues in Energy Systems 16 ­ 19 May, 2010, Sorrento, Italy I TRODUCTIO Heat pumps employed frost and defrost are transient phenomena, steady state models used by heat pump manufacturers do

  20. THE RADIOLOGICAL RESEARCH ACCELERATOR FACILITY The Radiological Research Accelerator Facility

    E-Print Network [OSTI]

    THE RADIOLOGICAL RESEARCH ACCELERATOR FACILITY 71 The Radiological Research Accelerator Facility the irradiated cells. Both the microbeam and the track segment facilities continue to be utilized in various investigations of this phenomenon. The single- particle microbeam facility provides precise control of the number

  1. THE RADIOLOGICAL RESEARCH ACCELERATOR FACILITY The Radiological Research Accelerator Facility

    E-Print Network [OSTI]

    THE RADIOLOGICAL RESEARCH ACCELERATOR FACILITY 1 The Radiological Research Accelerator Facility for Radiological Research (CRR). Using the mi- crobeam facility, 10% of the cells were irradiated through particle beam as well as the first fo- cused microbeam in the new microbeam facility. · Another significant

  2. The Radiological Research Accelerator THE RADIOLOGICAL RESEARCH ACCELERATOR FACILITY

    E-Print Network [OSTI]

    The Radiological Research Accelerator Facility #12;84 THE RADIOLOGICAL RESEARCH ACCELERATOR FACILITY Director: David J. Brenner, Ph.D., D.Sc., Manager: Stephen A. Marino, M.S. An NIH SupportedV/µm 4 He ions using the microbeam facility (Exp. 73) also continued. The transformation frequency

  3. Accelerating PV Cost Effectiveness Through Systems Design, Engineering, and Quality Assurance: Phase I Annual Technical Report, 4 November 2004 - 3 November 2005

    SciTech Connect (OSTI)

    Botkin, J.

    2006-07-01T23:59:59.000Z

    During Phase I of this PV Manufacturing R&D subcontract, PowerLight Corporation has made significant progress toward the reduction of installed costs for commercial-scale, rooftop PV systems. PowerLight has worked to reduce operating costs by improving long-term reliability and performance through the development of more sophisticated tools used in system design and monitoring. Additionally, PowerLight has implemented design improvements with the goal of reducing cost while maintaining and/or improving product quality. As part of this effort, PowerLight also modified manufacturing and shipping processes to accommodate these design changes, streamline material flow, reduce cost, and decrease waste streams. During Phase II of this project, PowerLight plans to continue this work with the goal of reducing system cost and improving system performance.

  4. Accelerating semantic graph databases on commodity clusters

    SciTech Connect (OSTI)

    Morari, Alessandro; Castellana, Vito G.; Haglin, David J.; Feo, John T.; Weaver, Jesse R.; Tumeo, Antonino; Villa, Oreste

    2013-10-06T23:59:59.000Z

    We are developing a full software system for accelerating semantic graph databases on commodity cluster that scales to hundreds of nodes while maintaining constant query throughput. Our framework comprises a SPARQL to C++ compiler, a library of parallel graph methods and a custom multithreaded runtime layer, which provides a Partitioned Global Address Space (PGAS) programming model with fork/join parallelism and automatic load balancing over a commodity clusters. We present preliminary results for the compiler and for the runtime.

  5. FASTBUS for the particle accelerator laboratories

    SciTech Connect (OSTI)

    Dawson, W.K.; Costrell, L.; Ikeda, H.; Ponting, P.J.; Walz, H.V.

    1985-05-01T23:59:59.000Z

    The FASTBUS modular high speed data acquisition and control system for high energy physics and other applications was described by Costrell and Dawson at the 1983 Particle Accelerator Conference. Both the specification and the implementation of this interlaboratory development have progressed considerably since that time. Because of its many attractive features, FASTBUS is currently in use in several major nuclear and high energy physics laboratories and is also finding application in other areas. 10 refs.

  6. Numerical and laboratory simulations of auroral acceleration

    SciTech Connect (OSTI)

    Gunell, H.; De Keyser, J. [1Belgian Institute for Space Aeronomy, Avenue Circulaire 3, B-1180 Brussels (Belgium)] [1Belgian Institute for Space Aeronomy, Avenue Circulaire 3, B-1180 Brussels (Belgium); Mann, I. [EISCAT Scientific Association, P.O. Box 812, SE-981 28 Kiruna, Sweden and Department of Physics, Umeå University, SE-901 87 Umeå (Sweden)] [EISCAT Scientific Association, P.O. Box 812, SE-981 28 Kiruna, Sweden and Department of Physics, Umeå University, SE-901 87 Umeå (Sweden)

    2013-10-15T23:59:59.000Z

    The existence of parallel electric fields is an essential ingredient of auroral physics, leading to the acceleration of particles that give rise to the auroral displays. An auroral flux tube is modelled using electrostatic Vlasov simulations, and the results are compared to simulations of a proposed laboratory device that is meant for studies of the plasma physical processes that occur on auroral field lines. The hot magnetospheric plasma is represented by a gas discharge plasma source in the laboratory device, and the cold plasma mimicking the ionospheric plasma is generated by a Q-machine source. In both systems, double layers form with plasma density gradients concentrated on their high potential sides. The systems differ regarding the properties of ion acoustic waves that are heavily damped in the magnetosphere, where the ion population is hot, but weakly damped in the laboratory, where the discharge ions are cold. Ion waves are excited by the ion beam that is created by acceleration in the double layer in both systems. The efficiency of this beam-plasma interaction depends on the acceleration voltage. For voltages where the interaction is less efficient, the laboratory experiment is more space-like.

  7. accelerator driven mox-plutonium: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rubbia, Carlo; Burgio, N; Carta, M; Santagata, A; Cinotti, L 2002-01-01 32 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  8. accelerator-driven subcritical reactor: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    J.; Parks, Geoffrey T.; Gonalves, Leonardo V.N.; de Neufville, Richard 2 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  9. accelerator-driven neutron source: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    consortium, will be the world's most spallation neutron source (by > x10 8 Thorium as a Fuel for Accelerator Driven Subcritical Electronuclear Systems CERN Preprints Summary:...

  10. Laser acceleration of ion beams

    E-Print Network [OSTI]

    I. A. Egorova; A. V. Filatov; A. V. Prozorkevich; S. A. Smolyansky; D. B. Blaschke; M. Chubaryan

    2007-02-01T23:59:59.000Z

    We consider methods of charged particle acceleration by means of high-intensity lasers. As an application we discuss a laser booster for heavy ion beams provided, e.g. by the Dubna nuclotron. Simple estimates show that a cascade of crossed laser beams would be necessary to provide additional acceleration to gold ions of the order of GeV/nucleon.

  11. I Investigation of Pellet Acceleration

    E-Print Network [OSTI]

    I Investigation of Pellet Acceleration by an Arc heated Gas Gun An Interim Report INVESTIGATION OP PELLET ACCELERATION BY AN ARC HEATED GAS GUN* An Interim Report on the Investigations carried, and K.-V. Weisberg Abstract. Deep penetration of pellets into the JET plasma may prove to be a useful

  12. SBA Growth Accelerator Fund Competition

    Broader source: Energy.gov [DOE]

    The U.S. Small Business Administration (SBA) is accepting applications for the Growth Accelerator Fund Competition to identify the nation's innovative accelerators and similar organizations and award them cash prizes they may use to fund their operations costs and allow them to bring startup competitions to scale and new ideas to life.

  13. Essay: Robert H. Siemann As Leader of the Advanced Accelerator Research Department

    SciTech Connect (OSTI)

    Colby, Eric R.; Hogan, Mark J.; /SLAC

    2011-11-14T23:59:59.000Z

    Robert H. Siemann originally conceived of the Advanced Accelerator Research Department (AARD) as an academic, experimental group dedicated to probing the technical limitations of accelerators while providing excellent educational opportunities for young scientists. The early years of the Accelerator Research Department B, as it was then known, were dedicated to a wealth of mostly student-led experiments to examine the promise of advanced accelerator techniques. High-gradient techniques including millimeter-wave rf acceleration, beam-driven plasma acceleration, and direct laser acceleration were pursued, including tests of materials under rf pulsed heating and short-pulse laser radiation, to establish the ultimate limitations on gradient. As the department and program grew, so did the motivation to found an accelerator research center that brought experimentalists together in a test facility environment to conduct a broad range of experiments. The Final Focus Test Beam and later the Next Linear Collider Test Accelerator provided unique experimental facilities for AARD staff and collaborators to carry out advanced accelerator experiments. Throughout the evolution of this dynamic program, Bob maintained a department atmosphere and culture more reminiscent of a university research group than a national laboratory department. His exceptional ability to balance multiple roles as scientist, professor, and administrator enabled the creation and preservation of an environment that fostered technical innovation and scholarship.

  14. Particle Acceleration in Astrophysical Sources

    E-Print Network [OSTI]

    Amato, Elena

    2015-01-01T23:59:59.000Z

    Astrophysical sources are extremely efficient accelerators. Some sources emit photons up to multi-TeV energies, a signature of the presence, within them, of particles with energies much higher than those achievable with the largest accelerators on Earth. Even more compelling evidence comes from the study of Cosmic Rays, charged relativistic particles that reach the Earth with incredibly high energies: at the highest energy end of their spectrum, these subatomic particles are carrying a macroscopic energy, up to a few Joules. Here I will address the best candidate sources and mechanisms as cosmic particle accelerators. I will mainly focus on Galactic sources such as Supernova Remnants and Pulsar Wind Nebulae, which being close and bright, are the best studied among astrophysical accelerators. These sources are held responsible for most of the energy that is put in relativistic particles in the Universe, but they are not thought to accelerate particles up to the highest individual energies, $\\approx 10^{20}$ eV...

  15. A Components Database Design and Implementation for Accelerators and Detectors

    SciTech Connect (OSTI)

    Chan, A.; Meyer, S.; /SLAC

    2011-08-31T23:59:59.000Z

    Many accelerator and detector systems being fabricated for the PEP-II Accelerator and BABAR Detector needed configuration control and calibration measurements tracked for their components. Instead of building a database for each distinct system, a Components Database was designed and implemented that can encompass any type of component and any type of measurement. In this paper we describe this database design that is especially suited for the engineering and fabrication processes of the accelerator and detector environments where there are thousands of unique component types. We give examples of information stored in the Components Database, which includes accelerator configuration, calibration measurements, fabrication history, design specifications, inventory, etc. The World Wide Web interface is used to access the data, and templates are available for international collaborations to collect data off-line.

  16. Data Management Group Annual Report

    E-Print Network [OSTI]

    Toronto, University of

    iv Data Management Group Annual Report 2003 City of Hamilton City of Toronto GO Transit Regional of York Toronto Transit Commission The Data Management Group is a research program located ........................................................................................................ 3 Text-based Data Retrieval System `drs

  17. Project X Accelerator R&D Plan

    SciTech Connect (OSTI)

    Not Available

    2008-01-31T23:59:59.000Z

    Project X is a high intensity proton facility conceived to support a world-leading program in neutrino and flavor physics over the next two decades at Fermilab. Project X is an integral part of the Fermilab Roadmap as described in the Fermilab Steering Group Report. Project X is based on an 8 GeV superconducting H-linac, paired with the existing (but modified) Main Injector and Recycler Ring, to provide in excess of 2 MW of beam power throughout the energy range 60-120 GeV, simultaneous with at least 100 kW of beam power at 8 GeV. The linac utilizes technology in common with the ILC over the energy range 0.6-8.0 GeV. Beam current parameters can be made identical to ILC resulting in identical rf generation and distribution systems. This alignment of ILC and Project X technologies allows for a shared development effort. The initial 0.6 GeV of the linac draws heavily on technology developed by Argonne National Laboratory for a facility for rare isotope beams. It is anticipated that the exact configuration and operating parameters of the linac will be defined through the R&D program and will retain alignment with the ILC plan as it evolves over this period. Utilization of the Recycler Ring as an H{sup -} stripper and accumulator ring is the key element that provides the flexibility to operate the linac with the same beam parameters as the ILC. The linac operates at 5 Hz with a total of 5.6 x 10{sup 13} H{sup -} ions delivered per pulse. H{sup -} are stripped at injection into the Recycler in a manner that 'paints' the beam both transversely and longitudinally to reduce space charge forces. Following the 1 ms injection, the orbit moves off the stripping foil and circulates for 200 msec, awaiting the next injection. Following three such injections a total of 1.7 x 10{sup 14} protons are transferred in a single turn to the Main Injector. These protons are then accelerated to 120 GeV and fast extracted to a neutrino target. The Main Injector cycle takes 1.4 seconds, producing approximately 2.3 MW of beam power at 120 GeV. At lower proton energies Main Injector cycle times can be shorter, allowing a beam power above 2 MW in the range of proton energy between 60 GeV and 120 GeV. In parallel, because the loading of the Recycler only requires 0.6 seconds, up to four linac cycles are available for accumulation and distribution of 8 GeV protons from the Recycler. Total available 8 GeV beam power lies in the range of 100-200 kW, depending on the energy in the Main Injector. Primary modifications to the existing accelerator complex to support Project X include integration of an H{sup -} injection system, a new RF system, a new extraction system, and measures to mitigate electron cloud effects, in the Recycler Ring. The Main Injector would need a new RF system, measures to preserve beam stability through transition, and measures to mitigate electron cloud effects. Finally, substantial modifications to the existing NuMI target station will be required to support >2 MW operations. It is anticipated that Project X configured as described above would initially support high intensity neutrino beams to the NOvA experiment, in parallel with at least one new 8 GeV based flavor/rare decay experiment. Depending upon future directions flexibility is retained for delivering neutrinos toward the DUSEL site and/or protons into the Tevatron. The purpose of this document is to describe an R&D plan that would position the U.S. to initiate construction of Project X in the 2012 time frame, assuming a go ahead decision in roughly 2010. The organization of this document is as follows: (1) Goals - Describes goals of the R&D and preliminary design period (2008-2011). Included are design, technical development, project documentation, and organizational goals. These are described in the context of an overall set of performance goals for Project X. (2) R&D Plan Elements - Describes the essential technical elements of the plan, including major subsystem performance requirements, associated accelerator and technology issues, and the plans for add

  18. Velocity bunching in travelling wave accelerator with low acceleration gradient

    E-Print Network [OSTI]

    Huang, Rui-Xuan; Li, Wei-Wei; Jia, Qi-Ka

    2013-01-01T23:59:59.000Z

    We present the analytical and simulated results concerning the influences of the acceleration gradient in the velocity bunching process, which is a bunch compression scheme that uses a traveling wave accelerating structure as a compressor. Our study shows that the bunch compression application with low acceleration gradient is more tolerant to phase jitter and more successful to obtain compressed electron beam with symmetrical longitudinal distribution and low energy spread. We also present a transverse emittance compensation scheme to compensate the emittance growth caused by the increasing of the space charge force in the compressing process that is easy to be adjusted for different compressing factors.

  19. Electron beam accelerator with magnetic pulse compression and accelerator switching

    DOE Patents [OSTI]

    Birx, D.L.; Reginato, L.L.

    1984-03-22T23:59:59.000Z

    An electron beam accelerator is described comprising an electron beam generator-injector to produce a focused beam of greater than or equal to .1 MeV energy electrons; a plurality of substantially identical, aligned accelerator modules to sequentially receive and increase the kinetic energies of the beam electron by about .1-1 MeV per module. Each accelerator module includes a pulse-forming network that delivers a voltage pulse to the module of substantially .1-1 MeV maximum energy over a time duration of less than or equal to 1 ..mu..sec.

  20. Accelerating Structure design and fabrication For KIPT and PAL XFEL

    E-Print Network [OSTI]

    Hou, Mi; Pei, Shilun

    2014-01-01T23:59:59.000Z

    ANL and the National Science Center "Kharkov Institute of Physics Technology" (NSC KIPT, Kharkov, Ukraine) jointly proposed to design and build a 100MeV/100KW linear accelerator which will be used to drive the neutron source subcritical assembly. Now the linac was almost assembled in KIPT by the team from Institute of High Energy Physics (IHEP, Beijing, China). The design and measurement result of the accelerating system of the linac will be described in this paper.

  1. Computer-based training for particle accelerator personnel

    SciTech Connect (OSTI)

    Silbar, Richard R. [WhistleSoft, Inc., 168 Dos Brazos, Los Alamos, New Mexico 87544 (United States)

    1999-06-10T23:59:59.000Z

    A continuing problem at many laboratories is the training of new operators in the arcane technology of particle accelerators. Presently most of this training occurs 'on the job,' under a mentor. Such training is expensive, and while it provides operational experience, it is frequently lax in providing the physics background needed to truly understand accelerator systems. Using computers in a self-paced, interactive environment can be more effective in meeting this training need.

  2. Relativistic Particle Acceleration in a Folded Current Sheet

    E-Print Network [OSTI]

    S. Zenitani; M. Hoshino

    2005-05-24T23:59:59.000Z

    Two-dimensional particle simulations of a relativistic Harris current sheet of pair plasmashave demonstrated that the system is unstable to the relativistic drift kink instability (RDKI) and that a new kind of acceleration process takes place in the deformed current sheet. This process contributes to the generation of non-thermal particles and contributes to the fast magnetic dissipation in the current sheet structure. The acceleration mechanism and a brief comparison with relativistic magnetic reconnection are presented.

  3. ELSEVIER Journal of Marine Systems 14 (1998) 181-198 Competition between different groups of phytoplankton for

    E-Print Network [OSTI]

    Dippner, Joachim W.

    . The behaviour of the autonomous system is discussed and the effect of eutrophication is investigated coastal eutrophication and examples of exceptional phytoplankton blooms are documented by Smetacek et al shift from diatoms to other algae can be ascribed to the eutrophication or not is a still open question

  4. This paper has been downloaded from the Building and Environmental Thermal Systems Research Group at Oklahoma State University

    E-Print Network [OSTI]

    on Outdoor Coils of Air-Source Heat Pumps. Proceedings of ASME-ATI-UIT. Conference on Thermal and Environmental Issues in Energy Systems 16 ­ 19 May, 2010, Sorrento, Italy INTRODUCTION Air source heat pump and have low installation cost. An air source heat pump exchanges heat directly from the indoor environment

  5. Information basis for developing comprehensive waste management system-US-Japan joint nuclear energy action plan waste management working group phase I report.

    SciTech Connect (OSTI)

    Nutt, M.; Nuclear Engineering Division

    2010-05-25T23:59:59.000Z

    The activity of Phase I of the Waste Management Working Group under the United States - Japan Joint Nuclear Energy Action Plan started in 2007. The US-Japan JNEAP is a bilateral collaborative framework to support the global implementation of safe, secure, and sustainable, nuclear fuel cycles (referred to in this document as fuel cycles). The Waste Management Working Group was established by strong interest of both parties, which arise from the recognition that development and optimization of waste management and disposal system(s) are central issues of the present and future nuclear fuel cycles. This report summarizes the activity of the Waste Management Working Group that focused on consolidation of the existing technical basis between the U.S. and Japan and the joint development of a plan for future collaborative activities. Firstly, the political/regulatory frameworks related to nuclear fuel cycles in both countries were reviewed. The various advanced fuel cycle scenarios that have been considered in both countries were then surveyed and summarized. The working group established the working reference scenario for the future cooperative activity that corresponds to a fuel cycle scenario being considered both in Japan and the U.S. This working scenario involves transitioning from a once-through fuel cycle utilizing light water reactors to a one-pass uranium-plutonium fuel recycle in light water reactors to a combination of light water reactors and fast reactors with plutonium, uranium, and minor actinide recycle, ultimately concluding with multiple recycle passes primarily using fast reactors. Considering the scenario, current and future expected waste streams, treatment and inventory were discussed, and the relevant information was summarized. Second, the waste management/disposal system optimization was discussed. Repository system concepts were reviewed, repository design concepts for the various classifications of nuclear waste were summarized, and the factors to consider in repository design and optimization were then discussed. Japan is considering various alternatives and options for the geologic disposal facility and the framework for future analysis of repository concepts was discussed. Regarding the advanced waste and storage form development, waste form technologies developed in both countries were surveyed and compared. Potential collaboration areas and activities were next identified. Disposal system optimization processes and techniques were reviewed, and factors to consider in future repository design optimization activities were also discussed. Then the potential collaboration areas and activities related to the optimization problem were extracted.

  6. Neutrino Factory Downstream Systems

    E-Print Network [OSTI]

    Zisman, Michael S.

    2010-01-01T23:59:59.000Z

    Neutrino Factory Downstream Systems Michael S. Zisman*Factory accelerator systems downstream from the target andthe Neutrino Factory systems downstream of the target and

  7. Radiological Research Accelerator Facility Service Request Form

    E-Print Network [OSTI]

    Radiological Research Accelerator Facility Service Request Form National Institute of Biomedical Imaging and Bioengineering Radiological Research Accelerator Facility Service request form Estimate when(s) to control for this experiment (if more than one, please prioritize): Radiological Research Accelerator

  8. FPGA Acceleration of Discrete Molecular Dynamics Simulation

    E-Print Network [OSTI]

    Herbordt, Martin

    ' & $ % FPGA Acceleration of Discrete Molecular Dynamics Simulation Joshua Model Thesis submitted UNIVERSITY COLLEGE OF ENGINEERING Thesis FPGA Acceleration of Discrete Molecular Dynamics Simulation Acceleration of Discrete Molecular Dynamics Simulation Joshua Model ABSTRACT Molecular dynamics simulation

  9. TOPICS IN THE PHYSICS OF PARTICLE ACCELERATORS

    E-Print Network [OSTI]

    Sessler, A.M.

    2008-01-01T23:59:59.000Z

    IN THE PHYSICS OF PARTICLE ACCELERATORS A.M. Sessler TWO-IN THE PHYSICS OF PARTICLE ACCELERATORS Andrew M. SesslerBruck, "Circular Particle Accelerators," PUF, Paris (1966).

  10. Energy Department Announces National Geothermal Data System to...

    Office of Environmental Management (EM)

    National Geothermal Data System to Accelerate Geothermal Energy Development Energy Department Announces National Geothermal Data System to Accelerate Geothermal Energy Development...

  11. Model-independent particle accelerator tuning

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Scheinker, Alexander; Pang, Xiaoying; Rybarcyk, Larry

    2013-10-01T23:59:59.000Z

    We present a new model-independent dynamic feedback technique, rotation rate tuning, for automatically and simultaneously tuning coupled components of uncertain, complex systems. The main advantages of the method are: 1) It has the ability to handle unknown, time-varying systems, 2) It gives known bounds on parameter update rates, 3) We give an analytic proof of its convergence and its stability, and 4) It has a simple digital implementation through a control system such as the Experimental Physics and Industrial Control System (EPICS). Because this technique is model independent it may be useful as a real-time, in-hardware, feedback-based optimization scheme formore »uncertain and time-varying systems. In particular, it is robust enough to handle uncertainty due to coupling, thermal cycling, misalignments, and manufacturing imperfections. As a result, it may be used as a fine-tuning supplement for existing accelerator tuning/control schemes. We present multi-particle simulation results demonstrating the scheme’s ability to simultaneously adaptively adjust the set points of twenty two quadrupole magnets and two RF buncher cavities in the Los Alamos Neutron Science Center (LANSCE) Linear Accelerator’s transport region, while the beam properties and RF phase shift are continuously varying. The tuning is based only on beam current readings, without knowledge of particle dynamics. We also present an outline of how to implement this general scheme in software for optimization, and in hardware for feedback-based control/tuning, for a wide range of systems.« less

  12. Negative hydrogen ion sources for accelerators

    SciTech Connect (OSTI)

    Moehs, D.P.; /Fermilab; Peters, J.; /DESY; Sherman, J.; /Los Alamos

    2005-08-01T23:59:59.000Z

    A variety of H{sup -} ion sources are in use at accelerator laboratories around the world. A list of these ion sources includes surface plasma sources with magnetron, Penning and surface converter geometries as well as magnetic-multipole volume sources with and without cesium. Just as varied is the means of igniting and maintaining magnetically confined plasmas. Hot and cold cathodes, radio frequency, and microwave power are all in use, as well as electron tandem source ignition. The extraction systems of accelerator H{sup -} ion sources are highly specialized utilizing magnetic and electric fields in their low energy beam transport systems to produce direct current, as well as pulsed and/or chopped beams with a variety of time structures. Within this paper, specific ion sources utilized at accelerator laboratories shall be reviewed along with the physics of surface and volume H{sup -} production in regard to source emittance. Current research trends including aperture modeling, thermal modeling, surface conditioning, and laser diagnostics will also be discussed.

  13. INFORMATION SYSTEMS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SYSTEMS Providing an efficient, seamless virtual work environment To accelerate progress toward mission goals, our business and operations processes will be aggressively...

  14. Cryomodule Design for the Rare Isotope Accelerator

    SciTech Connect (OSTI)

    Grimm, Terry; Hartung, Walter; Johnson, M.; York, Richard; Kneisel, Peter; Turlington, Larry

    2003-05-01T23:59:59.000Z

    The Rare Isotope Accelerator (RIA) driver linac will produce >400 MeV/u proton through uranium beams using many types of superconducting accelerating cavities such as quarter wave, spoke, and elliptical cavities. A cryomodule design that can accommodate all of the superconducting cavity and magnet types is presented. Alignment of the cold mass uses a titanium rail system, which minimizes cryomodule size, and decreases both the tunnel cross-section and length. The titanium rail is supported from the top vacuum plate by an adjustable trilink, which is similar to existing Michigan State University magnet technology. A prototype cryomodule is under construction for testing 805 MHz, v/c=0.47, sixcell niobium cavities in realistic operating conditions. Details of the design and progress to date are presented.

  15. ILC Reference Design Report Volume 3 - Accelerator

    E-Print Network [OSTI]

    Phinney, Nan; Walker, Nicholas

    2007-01-01T23:59:59.000Z

    The International Linear Collider (ILC) is a 200-500 GeV center-of-mass high-luminosity linear electron-positron collider, based on 1.3 GHz superconducting radio-frequency (SCRF) accelerating cavities. The ILC has a total footprint of about 31 km and is designed for a peak luminosity of 2x10^34 cm^-2 s^-1. The complex includes a polarized electron source, an undulator-based positron source, two 6.7 km circumference damping rings, two-stage bunch compressors, two 11 km long main linacs and a 4.5 km long beam delivery system. This report is Volume III (Accelerator) of the four volume Reference Design Report, which describes the design and cost of the ILC.

  16. Electron Surfing Acceleration in Magnetic Reconnection

    E-Print Network [OSTI]

    Masahiro Hoshino

    2005-07-22T23:59:59.000Z

    We discuss that energetic electrons are generated near the X-type magnetic reconnection region due to a surfing acceleration mechanism. In a thin plasma sheet, the polarization electric fields pointing towards the neutral sheet are induced around the boundary between the lobe and plasma sheet in association with the Hall electric current. By using a particle-in-cell simulation, we demonstrate that the polarization electric fields are strongly enhanced in an externally driven reconnection system, and some electrons can be trapped by the electrostatic potential well of the polarization field. During the trapping phase, the electrons can gain their energies from the convection/inductive reconnection electric fields. We discuss that relativistic electrons with MeV energies are quickly generated in and around the X-type neutral region by utilizing the surfing acceleration.

  17. Experimental test accelerator (ETA) II

    SciTech Connect (OSTI)

    Fessenden, T.J.; Atchison, W.L.; Birx, D.L.

    1981-03-06T23:59:59.000Z

    The Experimental Test Accelerator (ETA) is designed to produce a 10 kAmp electron beam at an energy of 4.5 MeV in 40 nsec pulses at an average rate of 2 pps. The accelerator also operates in bursts of 5 pulses spaced by as little as one millisec at an average rate of 5 pps. The machine is currently operating near 80% of its design values and has accumulated over 2.5 million pulses - mostly at a rate of one pps. The plasma cathode electron source, the remainder of the accelerator, and the operating characteristics of the machine are discussed.

  18. Cosmic Particle Acceleration: Basic Issues

    E-Print Network [OSTI]

    T. W. Jones

    2000-12-22T23:59:59.000Z

    Cosmic-rays are ubiquitous, but their origins are surprisingly difficult to understand. A review is presented of some of the basic issues common to cosmic particle accelerators and arguments leading to the likely importance of diffusive shock acceleration as a general explanation. The basic theory of diffusive shock acceleration is outlined, followed by a discussion of some of the key issues that still prevent us from a full understanding of its outcomes. Some recent insights are mentioned at the end that may help direct ultimate resolution of our uncertainties.

  19. Terahertz radiation from laser accelerated electron bunches

    E-Print Network [OSTI]

    2004-01-01T23:59:59.000Z

    NUMBER 5 MAY 2004 Terahertz radiation from laser acceleratedand millimeter wave radiation from laser acceleratedNo. 5, May 2004 Terahertz radiation from laser accelerated

  20. ASTA at Fermilab: Accelerator Physics and Accelerator Education Programs at the Modern Accelerator R&D Users Facility for HEP and Accelerator Applications.

    SciTech Connect (OSTI)

    Shiltsev, V.; Piot, P.

    2013-09-01T23:59:59.000Z

    We present the current and planned beam physics research program and accelerator education program at Advanced Superconducting Test Accelerator (ASTA) at Fermilab.

  1. Accelerating CHP Deployment, United States Energy Association...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Accelerating CHP Deployment, United States Energy Association (USEA), August 2011 Accelerating CHP Deployment, United States Energy Association (USEA), August 2011 The United...

  2. Berkeley Lab Compact Accelerator Sets World Record

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Berkeley Lab Particle Accelerator Sets World Record Berkeley Lab Particle Accelerator Sets World Record Simulations at NERSC Help Validate Experimental Laser-Plasma Design December...

  3. Iterative acceleration methods for Monte Carlo and deterministic criticality calculations

    SciTech Connect (OSTI)

    Urbatsch, T.J.

    1995-11-01T23:59:59.000Z

    If you have ever given up on a nuclear criticality calculation and terminated it because it took so long to converge, you might find this thesis of interest. The author develops three methods for improving the fission source convergence in nuclear criticality calculations for physical systems with high dominance ratios for which convergence is slow. The Fission Matrix Acceleration Method and the Fission Diffusion Synthetic Acceleration (FDSA) Method are acceleration methods that speed fission source convergence for both Monte Carlo and deterministic methods. The third method is a hybrid Monte Carlo method that also converges for difficult problems where the unaccelerated Monte Carlo method fails. The author tested the feasibility of all three methods in a test bed consisting of idealized problems. He has successfully accelerated fission source convergence in both deterministic and Monte Carlo criticality calculations. By filtering statistical noise, he has incorporated deterministic attributes into the Monte Carlo calculations in order to speed their source convergence. He has used both the fission matrix and a diffusion approximation to perform unbiased accelerations. The Fission Matrix Acceleration method has been implemented in the production code MCNP and successfully applied to a real problem. When the unaccelerated calculations are unable to converge to the correct solution, they cannot be accelerated in an unbiased fashion. A Hybrid Monte Carlo method weds Monte Carlo and a modified diffusion calculation to overcome these deficiencies. The Hybrid method additionally possesses reduced statistical errors.

  4. Automata groups

    E-Print Network [OSTI]

    Muntyan, Yevgen

    2010-01-16T23:59:59.000Z

    automata over the alphabet of 2 letters and 2-state automata over the 3-letter alphabet. We continue the classification work started by the research group at Texas A&M University ([BGK+07a, BGK+07b]) and further reduce the number of pairwise nonisomorphic...

  5. Workshop on Accelerators for Heavy Ion Fusion: Summary Report of the Workshop

    SciTech Connect (OSTI)

    Seidl, P.A.; Barnard, J.J.

    2011-04-29T23:59:59.000Z

    The Workshop on Accelerators for Heavy Ion Fusion was held at Lawrence Berkeley National Laboratory May 23-26, 2011. The workshop began with plenary sessions to review the state of the art in HIF (heavy ion fusion), followed by parallel working groups, and concluded with a plenary session to review the results. There were five working groups: IFE (inertial fusion energy) targets, RF approach to HIF, induction accelerator approach to HIF, chamber and driver interface, ion sources and injectors.

  6. Linear Accelerator | Advanced Photon Source

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    photo below). Selective phasing of the electric field accelerates the electrons to 450 million volts (MeV). At 450 MeV, the electrons are relativistic: they are traveling at...

  7. The Sustainable Building-Accelerator 

    E-Print Network [OSTI]

    Maassen, W.H.

    2011-01-01T23:59:59.000Z

    stages to generate optimal design solutions. The ''Sustainable Building - Accelerator'' supports stakeholders to decide on sustainable solutions by giving them cost and benefit information of design solutions. This information provides them...

  8. Israel Careers ACCELERATE YOUR FUTURE

    E-Print Network [OSTI]

    Rimon, Elon

    Lithography Control products within the product lifecycle process including defining requirements, settingIsrael Careers ACCELERATE YOUR FUTURE Product Marketing Manager Job Description: Product Marketing Manager at the Optical Metrology Division is responsible for product strategy and customer interface

  9. Sequentially pulsed traveling wave accelerator

    DOE Patents [OSTI]

    Caporaso, George J. (Livermore, CA); Nelson, Scott D. (Patterson, CA); Poole, Brian R. (Tracy, CA)

    2009-08-18T23:59:59.000Z

    A sequentially pulsed traveling wave compact accelerator having two or more pulse forming lines each with a switch for producing a short acceleration pulse along a short length of a beam tube, and a trigger mechanism for sequentially triggering the switches so that a traveling axial electric field is produced along the beam tube in synchronism with an axially traversing pulsed beam of charged particles to serially impart energy to the particle beam.

  10. BRIEF HISTORY OF FFAG ACCELERATORS.

    SciTech Connect (OSTI)

    RUGGIERO, A.

    2006-12-04T23:59:59.000Z

    Colleagues of mine have asked me few times why we have today so much interest in Fixed-Field Alternating-Gradient (FFAG) accelerators when these were invented a long time ago, and have always been ignored since then. I try here to give a reply with a short history of FFAG accelerators, at least as I know it. I take also the opportunity to clarify few definitions.

  11. Materials considerations for a high power-density accelerator

    SciTech Connect (OSTI)

    Michelotti, R.A.; Tennant, R.A.; Bultman, N.K.; Uher, J.L.; Brewton, R.J.; Mayer, A.

    1985-01-01T23:59:59.000Z

    A 100-mA 50-MeV H/sup -/ accelerator is being designed at Los Alamos. The accelerating structures will operate at 425-MHz and will consist of a radio-frequency quadrupole (RFQ) to 2-MeV and a drift-tube linac (DTL) from 2 to 50-MeV. Design parameters have been specified to match the maximum operating capabilities of the rf system: 2-ms pulse length and 6% duty factor. The accelerating gradient in the DTL will be 4-MV/m; the maximum electric field will be approximately 1.2 times the Kilpatrick limit. These design parameters are substantially more ambitious than those of the accelerating test stand (ATS). That copper will be used on the rf-structure surfaces is not in question. Concern with residual activation and thermal management forces the investigation of materials other than the traditional carbon- and stainless-steel base materials used at Los Alamos.

  12. Control system for the Holifield Radioactive Ion Beam Facility

    SciTech Connect (OSTI)

    Tatum, B.A.; Juras, R.C.; Meigs, M.J.

    1995-12-31T23:59:59.000Z

    A new accelerator control system is being implemented as part of the development of the Holifield Radioactive Ion Beam Facility (HRIBF), a first generation radioactive ion beam (RIB) facility. The pre- existing accelerator control systems are based on 1970`s technology and addition or alteration of controls is cumbersome and costly. A new, unified control system for the cyclotron and tandem accelerators, the RIB injector, ion sources, and accelerator beam lines is based on a commercial product from Vista Control Systems, Inc. Several other accelerator facilities, as well as numerous industrial sites, are now using this system. The control system is distributed over a number of computers which communicate over Ethernet and is easily extensible. Presently, implementation at the HRIBF is based on VAX/VMS, VAX/ELN, VME, and Allen-Bradley PLC5 programmable logic controller architectures. Expansion to include UNIX platforms and CAMAC hardware support is planned. Operator interface is via X- terminals. The system has proven to be quite powerful, yet is has been easy to implement with a small staff. A Vista users group has resulted in shared software to implement specific controls. This paper details present system features and future implementations at the HRIBF.

  13. Finite group symmetry breaking

    E-Print Network [OSTI]

    G. Gaeta

    2005-10-02T23:59:59.000Z

    Finite group symmetry is commonplace in Physics, in particular through crystallographic groups occurring in condensed matter physics -- but also through the inversions (C,P,T and their combinations) occurring in high energy physics and field theory. The breaking of finite groups symmetry has thus been thoroughly studied, and general approaches exist to investigate it. In Landau theory, the state of a system is described by a finite dimensional variable (the {\\it order parameter}), and physical states correspond to minima of a potential, invariant under a group. In this article we describe the basics of symmetry breaking analysis for systems described by a symmetric polynomial; in particular we discuss generic symmetry breakings, i.e. those determined by the symmetry properties themselves and independent on the details of the polynomial describing a concrete system. We also discuss how the plethora of invariant polynomials can be to some extent reduced by means of changes of coordinates, i.e. how one can reduce to consider certain types of polynomials with no loss of generality. Finally, we will give some indications on extension of this theory, i.e. on how one deals with symmetry breakings for more general groups and/or more general physical systems.

  14. Testing a combined vibration and acceleration environment.

    SciTech Connect (OSTI)

    Jepsen, Richard Alan; Romero, Edward F.

    2005-01-01T23:59:59.000Z

    Sandia National Laboratories has previously tested a capability to impose a 7.5 g-rms (30 g peak) radial vibration load up to 2 kHz on a 25 lb object with superimposed 50 g acceleration at its centrifuge facility. This was accomplished by attaching a 3,000 lb Unholtz-Dickie mechanical shaker at the end of the centrifuge arm to create a 'Vibrafuge'. However, the combination of non-radial vibration directions, and linear accelerations higher than 50g's are currently not possible because of the load capabilities of the shaker and the stresses on the internal shaker components due to the combined centrifuge acceleration. Therefore, a new technique using amplified piezo-electric actuators has been developed to surpass the limitations of the mechanical shaker system. They are lightweight, modular and would overcome several limitations presented by the current shaker. They are 'scalable', that is, adding more piezo-electric units in parallel or in series can support larger-weight test articles or displacement/frequency regimes. In addition, the units could be mounted on the centrifuge arm in various configurations to provide a variety of input directions. The design along with test results will be presented to demonstrate the capabilities and limitations of the new piezo-electric Vibrafuge.

  15. Unruh effect and condensate in and out of an accelerated vacuum

    E-Print Network [OSTI]

    Sanjin Benic; Kenji Fukushima

    2015-03-31T23:59:59.000Z

    We address a physical interpretation of the Hawking-Unruh effect with our emphasis put on judicious consideration of observables and vacua with and without acceleration. In particular we discuss thermal-like corrections using explicit computation of correlation functions. We identify the correspondence between thermo-field dynamics and accelerated systems. Then we make it clear that a genuine thermal state corresponds to a non-accelerated frame, while vacuum states correspond to Rindler wedges, which accounts for a negative contribution of the thermal-like correction measured in the accelerated vacuum. We apply our results to investigate how the acceleration effect would affect a condensate of fields. Our conclusion is that a larger acceleration should enhance a condensate as compared to those in a non-accelerated vacuum.

  16. Data Management Group Annual Report

    E-Print Network [OSTI]

    Toronto, University of

    Data Management Group Annual Report 2000 prepared by: Data Management Group Joint Program the operation of the EMME/2 simu- lation package on the Data Management Group's computer system. During the year computing resource at the DMG. A major challenge in 2000 was to maintain this service while operating out

  17. High Gradient Two-Beam Electron Accelerator

    SciTech Connect (OSTI)

    Jiang, Y. [Beam Physics Laboratory, Yale University, 272 Whitney Ave., New Haven, CT 06511 (United States); Kazakov, S. Yu. [Omega-P, Inc., 258 Bradley St., New Haven, CT 06510 (United States); Fermi National Accelerator Laboratory, Batavia, IL 60510 (United States); Kuzikov, S. V. [Omega-P, Inc., 258 Bradley St., New Haven, CT 06510 (United States); Institute of Applied Physics, Nizhny Novgorod, 603600 (Russian Federation); Hirshfield, J. L. [Beam Physics Laboratory, Yale University, 272 Whitney Ave., New Haven, CT 06511 (United States); Omega-P, Inc., 258 Bradley St., New Haven, CT 06510 (United States)

    2010-11-04T23:59:59.000Z

    A high-gradient two-beam electron accelerator structure using detuned cavities is described. A self-consistent theory based on a circuit model is presented to calculate idealized acceleration gradient, transformer ratio, and efficiency for energy transfer from the drive beam to the accelerated beam. Experimental efforts are being carried out to demonstrate this acceleration concept.

  18. RADIO EMISSION OF SOLAR FLARE PARTICLE ACCELERATION

    E-Print Network [OSTI]

    RADIO EMISSION OF SOLAR FLARE PARTICLE ACCELERATION A. O. Benz Abstract The solar corona is a very be considered as a particle accelerator. The free mobility of charged particles in a dilute plasma to accelerate particles in resonance. From a plasma physics point of view, acceleration is not surprising

  19. Transformer ratio improvement for beam based plasma accelerators

    SciTech Connect (OSTI)

    O'Shea, Brendan; Rosenzweig, James; Barber, Samuel; Fukasawa, Atsushi; Williams, Oliver; Muggli, Patric; Yakimenko, Vitaly; Kusche, Karl [University of California, Los Angeles, Department of Physics and Astronomy, Los Angeles, CA 90095 (United States); University of Southern California, Department of Electrical Engineering, Los Angeles, CA 90089 U.S.A. and Max-Planck-Institut fuer Physik, Foehringer Ring 6, 80805 Muenchen (Germany); Accelerator Test Facility, Brookhaven National Lab, Upton, NY, 11973 (United States)

    2012-12-21T23:59:59.000Z

    Increasing the transformer ratio of wakefield accelerating systems improves the viability of present novel accelerating schemes. The use of asymmetric bunches to improve the transformer ratio of beam based plasma systems has been proposed for some time[1, 2] but suffered from lack appropriate beam creation systems. Recently these impediments have been overcome [3, 4] and the ability now exists to create bunches with current profiles shaped to overcome the symmetric beam limit of R {<=} 2. We present here work towards experiments designed to measure the transformer ratio of such beams, including theoretical models and simulations using VORPAL (a 3D capable PIC code) [5]. Specifically we discuss projects to be carried out in the quasi-nonlinear regime [6] at the UCLA Neptune Laboratory and the Accelerator Test Facility at Brookhaven National Lab.

  20. Accelerator and electrodynamics capability review

    SciTech Connect (OSTI)

    Jones, Kevin W [Los Alamos National Laboratory

    2010-01-01T23:59:59.000Z

    Los Alamos National Laboratory (LANL) uses capability reviews to assess the science, technology and engineering (STE) quality and institutional integration and to advise Laboratory Management on the current and future health of the STE. Capability reviews address the STE integration that LANL uses to meet mission requirements. The Capability Review Committees serve a dual role of providing assessment of the Laboratory's technical contributions and integration towards its missions and providing advice to Laboratory Management. The assessments and advice are documented in reports prepared by the Capability Review Committees that are delivered to the Director and to the Principal Associate Director for Science, Technology and Engineering (PADSTE). Laboratory Management will use this report for STE assessment and planning. LANL has defined fifteen STE capabilities. Electrodynamics and Accelerators is one of the seven STE capabilities that LANL Management (Director, PADSTE, technical Associate Directors) has identified for review in Fiscal Year (FY) 2010. Accelerators and electrodynamics at LANL comprise a blend of large-scale facilities and innovative small-scale research with a growing focus on national security applications. This review is organized into five topical areas: (1) Free Electron Lasers; (2) Linear Accelerator Science and Technology; (3) Advanced Electromagnetics; (4) Next Generation Accelerator Concepts; and (5) National Security Accelerator Applications. The focus is on innovative technology with an emphasis on applications relevant to Laboratory mission. The role of Laboratory Directed Research and Development (LDRD) in support of accelerators/electrodynamics will be discussed. The review provides an opportunity for interaction with early career staff. Program sponsors and customers will provide their input on the value of the accelerator and electrodynamics capability to the Laboratory mission.

  1. Ultra-high vacuum photoelectron linear accelerator

    DOE Patents [OSTI]

    Yu, David U.L.; Luo, Yan

    2013-07-16T23:59:59.000Z

    An rf linear accelerator for producing an electron beam. The outer wall of the rf cavity of said linear accelerator being perforated to allow gas inside said rf cavity to flow to a pressure chamber surrounding said rf cavity and having means of ultra high vacuum pumping of the cathode of said rf linear accelerator. Said rf linear accelerator is used to accelerate polarized or unpolarized electrons produced by a photocathode, or to accelerate thermally heated electrons produced by a thermionic cathode, or to accelerate rf heated field emission electrons produced by a field emission cathode.

  2. The BErkeley Lab Laser Accelerator (BELLA): A 10 GeV Laser Plasma Accelerator

    SciTech Connect (OSTI)

    Leemans, W.P.; Duarte, R.; Esarey, E.; Fournier, S.; Geddes, C.G.R.; Lockhart, D.; Schroeder, C.B.; Toth, C.; Vay, J.-L.; Zimmermann, S.

    2010-06-01T23:59:59.000Z

    An overview is presented of the design of a 10 GeV laser plasma accelerator (LPA) that will be driven by a PW-class laser system and of the BELLA Project, which has as its primary goal to build and install the required Ti:sapphire laser system for the acceleration experiments. The basic design of the 10 GeV stage aims at operation in the quasi-linear regime, where the laser excited wakes are largely sinusoidal and offer the possibility of accelerating both electrons and positrons. Simulations show that a 10 GeV electron beam can be generated in a meter scale plasma channel guided LPA operating at a density of about 1017 cm-3 and powered by laser pulses containing 30-40 J of energy in a 50- 200 fs duration pulse, focused to a spotsize of 50-100 micron. The lay-out of the facility and laser system will be presented as well as the progress on building the facility.

  3. Accelerator Physics Accelerators form the backbone of SLAC's on-site experimental program. Research at SLAC

    E-Print Network [OSTI]

    Wechsler, Risa H.

    #12;Accelerator Physics Accelerators form the backbone of SLAC's on-site experimental program. Research at SLAC is continually improving accelerators, both here and at other laboratories, and paving the way for a new generation of particle acceleration technology. SLAC's famous linear accelerator

  4. KKG Group Paraffin Removal

    SciTech Connect (OSTI)

    Schulte, Ralph

    2001-12-01T23:59:59.000Z

    The Rocky Mountain Oilfield Testing Center (RMOTC) has recently completed a test of a paraffin removal system developed by the KKG Group utilizing the technology of two Russian scientists, Gennady Katzyn and Boris Koggi. The system consisting of chemical ''sticks'' that generate heat in-situ to melt the paraffin deposits in oilfield tubing. The melted paraffin is then brought to the surface utilizing the naturally flowing energy of the well.

  5. Design report on the test system used to assess treatment of trench water from Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect (OSTI)

    Kent, T.E.; Taylor, P.A.

    1992-09-01T23:59:59.000Z

    New liquid waste streams will be generated as a consequence of closure activities at Waste Area Grouping (WAG) 6 at Oak Ridge National Laboratory (ORNL). It is proposed that these waste streams be treated for removal of contaminants by adding them to the ORNL wastewater treatment facilities. Previous bench-scale treatability studies indicate that ORNL treatment operations will adequately remove the contaminants, although additional study is required to characterize the secondary waste materials produced as a result of the treatment. A larger scale treatment system was constructed to produce secondary wastes in the quantities necessary for characterization and US Environmental protection Agency toxicity characteristic leaching procedure (TCLP) testing. The test system is designed to simulate the operation of the ORNL process waste treatment facilities and to treat a mixture of ORNL process wastewater and WAG 6 wastewater at a combined flow rate of 0.5 L/min. The system is designed to produce the necessary quantities of waste sludges and spent carbon for characterization studies and TCLP testing.

  6. Quantum Ratchet Accelerator without a Bichromatic Lattice Potential

    E-Print Network [OSTI]

    Jiao Wang; Jiangbin Gong

    2008-06-24T23:59:59.000Z

    In a quantum ratchet accelerator system, a linearly increasing directed current can be dynamically generated without using a biased field. Generic quantum ratchet acceleration with full classical chaos [Gong and Brumer, Phys. Rev. Lett. 97, 240602 (2006)] constitutes a new element of quantum chaos and an interesting violation of a sum rule of classical ratchet transport. Here we propose a simple quantum ratchet accelerator model that can also generate linearly increasing quantum current with full classical chaos. This new model does not require a bichromatic lattice potential. It is based on a variant of an on-resonance kicked-rotor system, periodically kicked by two optical lattice potentials of the same lattice constant, but with unequal amplitudes and a fixed phase shift between them. The dependence of the ratchet current acceleration rate on the system parameters is studied in detail. The cold-atom version of our new quantum ratchet accelerator model should be realizable by introducing slight modifications to current cold-atom experiments.

  7. Radiation from Bodies with Extreme Acceleration II: Kinematics

    E-Print Network [OSTI]

    Ulrich H. Gerlach

    2003-07-10T23:59:59.000Z

    When applied to a dipole source subjected to acceleration which is violent and long lasting (``extreme acceleration''), Maxwell's equations predict radiative power which augments Larmor's classical radiation formula by a nontrivial amount. The physical assumptions behind this result are made possible by the kinematics of a system of geometrical clocks whose tickings are controlled by cavities which are expanding inertially. For the purpose of measuring the radiation from such a source we take advantage of the physical validity of a spacetime coordinate framework (``inertially expanding frame'') based on such clocks. They are compatible and commensurable with the accelerated clocks of the accelerated source. By contrast, a common Lorentz frame with its mutually static clocks won't do: it lacks that commensurability. Inertially expanding clocks give a physicist a window into the frame of a source with extreme acceleration. He thus can locate that source and measure radiation from it without being subjected to such acceleration himself. The conclusion is that inertially expanding reference frames reveal qualitatively distinct aspects of nature which would not be accessible if static inertial frames were the only admissible frames.

  8. Beam-driven acceleration in ultra-dense plasma media

    SciTech Connect (OSTI)

    Shin, Young-Min [Fermi National Accelerator Laboratory, Batavia, IL (United States)

    2014-09-15T23:59:59.000Z

    Accelerating parameters of beam-driven wakefield acceleration in an extremely dense plasma column has been analyzed with the dynamic framed particle-in-cell plasma simulator, and compared with analytic calculations. In the model, a witness beam undergoes a TeV/m scale alternating potential gradient excited by a micro-bunched drive beam in a 1025 m-3 and 1.6 x 1028 m-3 plasma column. The acceleration gradient, energy gain, and transformer ratio have been extensively studied in quasi-linear, linear-, and blowout-regimes. The simulation analysis indicated that in the beam-driven acceleration system a hollow plasma channel offers 20 % higher acceleration gradient by enlarging the channel radius (r) from 0.2 ?p to 0.6 ?p in a blowout regime. This paper suggests a feasibility of TeV/m scale acceleration with a hollow crystalline structure (e.g. nanotubes) of high electron plasma density.

  9. Beam-driven acceleration in ultra-dense plasma media

    SciTech Connect (OSTI)

    Shin, Young-Min [Department of Physics, Northern Illinois University, Dekalb, Illinois 60115 (United States); Accelerator Physics Center (APC), Fermi National Accelerator Laboratory (FNAL), Batavia, Illinois 60510 (United States)

    2014-09-15T23:59:59.000Z

    Accelerating parameters of beam-driven wakefield acceleration in an extremely dense plasma column has been analyzed with the dynamic framed particle-in-cell plasma simulator, and compared with analytic calculations. In the model, a witness beam undergoes a TeV/m scale alternating potential gradient excited by a micro-bunched drive beam in a 10{sup 25?}m{sup ?3} and 1.6?×?10{sup 28?}m{sup ?3} plasma column. The acceleration gradient, energy gain, and transformer ratio have been extensively studied in quasi-linear, linear-, and blowout-regimes. The simulation analysis indicated that in the beam-driven acceleration system a hollow plasma channel offers ?20% higher acceleration gradient by enlarging the channel radius (r) from 0.2 ?{sub p} to 0.6 ?{sub p} in a blowout regime. This paper suggests a feasibility of TeV/m scale acceleration with a hollow crystalline structure (e.g., nanotubes) of high electron plasma density.

  10. Accelerated Randomized Benchmarking

    E-Print Network [OSTI]

    Christopher Granade; Christopher Ferrie; D. G. Cory

    2014-09-24T23:59:59.000Z

    Quantum information processing offers promising advances for a wide range of fields and applications, provided that we can efficiently assess the performance of the control applied in candidate systems. That is, we must be able to determine whether we have implemented a desired gate, and refine accordingly. Randomized benchmarking reduces the difficulty of this task by exploiting symmetries in quantum operations. Here, we bound the resources required for benchmarking and show that, with prior information, we can achieve several orders of magnitude better accuracy than in traditional approaches to benchmarking. Moreover, by building on state-of-the-art classical algorithms, we reach these accuracies with near-optimal resources. Our approach requires an order of magnitude less data to achieve the same accuracies and to provide online estimates of the errors in the reported fidelities. We also show that our approach is useful for physical devices by comparing to simulations. Our results thus enable the application of randomized benchmarking in new regimes, and dramatically reduce the experimental effort required to assess control fidelities in quantum systems. Finally, our work is based on open-source scientific libraries, and can readily be applied in systems of interest.

  11. Analysis of Transmitted Optical Spectrum Enabling Accelerated Testing of CPV Designs: Preprint

    SciTech Connect (OSTI)

    Miller, D. C.; Kempe, M. D.; Kennedy, C. E.; Kurtz, S. R.

    2009-07-01T23:59:59.000Z

    Reliability of CPV systems' materials is not well known; methods for accelerated UV testing have not been developed. UV and IR spectra transmitted through representative optical systems are evaluated.

  12. Superconducting Magnets for Particle Accelerators

    E-Print Network [OSTI]

    Rossi, L

    2012-01-01T23:59:59.000Z

    Superconductivity has been the most influential technology in the field of accelerators in the last 30 years. Since the commissioning of the Tevatron, which demonstrated the use and operability of superconductivity on a large scale, superconducting magnets and rf cavities have been at the heart of all new large accelerators. Superconducting magnets have been the invariable choice for large colliders, as well as cyclotrons and large synchrotrons. In spite of the long history of success, superconductivity remains a difficult technology, requires adequate R&D and suitable preparation, and has a relatively high cost. Hence, it is not surprising that the development has also been marked by a few setbacks. This article is a review of the main superconducting accelerator magnet projects; it highlights the main characteristics and main achievements, and gives a perspective on the development of superconducting magnets for the future generation of very high energy colliders.

  13. Virtual gap dielectric wall accelerator

    DOE Patents [OSTI]

    Caporaso, George James; Chen, Yu-Jiuan; Nelson, Scott; Sullivan, Jim; Hawkins, Steven A

    2013-11-05T23:59:59.000Z

    A virtual, moving accelerating gap is formed along an insulating tube in a dielectric wall accelerator (DWA) by locally controlling the conductivity of the tube. Localized voltage concentration is thus achieved by sequential activation of a variable resistive tube or stalk down the axis of an inductive voltage adder, producing a "virtual" traveling wave along the tube. The tube conductivity can be controlled at a desired location, which can be moved at a desired rate, by light illumination, or by photoconductive switches, or by other means. As a result, an impressed voltage along the tube appears predominantly over a local region, the virtual gap. By making the length of the tube large in comparison to the virtual gap length, the effective gain of the accelerator can be made very large.

  14. Symposium on accelerator mass spectrometry

    SciTech Connect (OSTI)

    None

    1981-01-01T23:59:59.000Z

    The area of accelerator mass spectrometry has expanded considerably over the past few years and established itself as an independent and interdisciplinary research field. Three years have passed since the first meeting was held at Rochester. A Symposium on Accelerator Mass Spectrometry was held at Argonne on May 11-13, 1981. In attendance were 96 scientists of whom 26 were from outside the United States. The present proceedings document the program and excitement of the field. Papers are arranged according to the original program. A few papers not presented at the meeting have been added to complete the information on the status of accelerator mass spectrometry. Individual papers were prepared separately for the data base.

  15. Efficient control of accelerator maps

    E-Print Network [OSTI]

    Jehan Boreux; Timoteo Carletti; Charalampos Skokos; Yannis Papaphilippou; Michel Vittot

    2011-09-21T23:59:59.000Z

    Recently, the Hamiltonian Control Theory was used in [Boreux et al.] to increase the dynamic aperture of a ring particle accelerator having a localized thin sextupole magnet. In this letter, these results are extended by proving that a simplified version of the obtained general control term leads to significant improvements of the dynamic aperture of the uncontrolled model. In addition, the dynamics of flat beams based on the same accelerator model can be significantly improved by a reduced controlled term applied in only 1 degree of freedom.

  16. Accelerated dynamics simulations of nanotubes.

    SciTech Connect (OSTI)

    Uberuaga, B. P. (Blas Pedro); Stuart, S. J. (Steve J.); Voter, A. F.

    2002-01-01T23:59:59.000Z

    We report on the application of accelerated dynamics techniques to the study of carbon nanotubes. We have used the parallel replica method and temperature accelerated dynamics simulations are currently in progress. In the parallel replica study, we have stretched tubes at a rate significantly lower than that used in previous studies. In these preliminary results, we find that there are qualitative differences in the rupture of the nanotubes at different temperatures. We plan on extending this investigation to include nanotubes of various chiralities. We also plan on exploring unique geometries of nanotubes.

  17. Electron Cloud Effects in Accelerators

    SciTech Connect (OSTI)

    Furman, M.A.

    2012-11-30T23:59:59.000Z

    Abstract We present a brief summary of various aspects of the electron-cloud effect (ECE) in accelerators. For further details, the reader is encouraged to refer to the proceedings of many prior workshops, either dedicated to EC or with significant EC contents, including the entire ?ECLOUD? series [1?22]. In addition, the proceedings of the various flavors of Particle Accelerator Conferences [23] contain a large number of EC-related publications. The ICFA Beam Dynamics Newsletter series [24] contains one dedicated issue, and several occasional articles, on EC. An extensive reference database is the LHC website on EC [25].

  18. COMPASS, the COMmunity Petascale project for Accelerator Science and Simulation, a broad computational accelerator physics

    E-Print Network [OSTI]

    Geddes, Cameron Guy Robinson

    COMPASS, the COMmunity Petascale project for Accelerator Science and Simulation, a broad at Lawrence Livermore National Laboratory. #12;COMPASS, the COMmunity Petascale project for Accelerator for materials studies. COMPASS, the Community Petascale Project for Accelerator Science and Simulation

  19. Energy Systems Group Annual Report 

    E-Print Network [OSTI]

    Anand, N. K.; Caton, J.; Heffington, W. M.; O'Neal, D. L.; Somasundaram, S.; Turner, W. D.

    1986-01-01T23:59:59.000Z

    . The principal investigator on this project is Dr. D.L. O'Neal. Frost can have an adverse impact on the energy use and capacity of heat pumps operating in the heating mode at outdoor temperatures between 20 and 40 F. The objective of this project... model of the frost formation process will also be developed. An Analysis of Efficiency Improvements in Heat Pumps. funded by Lawrence Berkeley Laboratory (U.S. Department of Energy). Air-to-air heat pump technology has improved dramatically over the past...

  20. Nick Balthaser! Storage Systems Group

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for Renewable Energy:Nanowire Solar541,9337,2April 2013 ESH&SNextNexusLBNL/NERSC

  1. Jay Srinivasan! NERSC Systems Group!

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12 Investigation PeerNOON...January 2015 1663The4 June,NERSC

  2. Traction Drive Systems Breakout Group

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn April 23,EnergyChicopeeTechnologyfact sheet summarizesof

  3. JSAC SPECIAL ISSUE ON NETWORK SUPPORT FOR GROUP COMMUNICATION 1 Scalable Secure Group Communication over IP

    E-Print Network [OSTI]

    Banerjee, Suman

    JSAC SPECIAL ISSUE ON NETWORK SUPPORT FOR GROUP COMMUNICATION 1 Scalable Secure Group Communication our scheme is completely end­host based, it can be used to implement group security over IP multicast­enabled untrusted, insecure networks. A. Group Keys and Re­keying Groups Many secure group communication systems [12

  4. Plasma Wakefield Acceleration and FACET - Facilities for Accelerator Science and Experimental Test Beams at SLAC

    ScienceCinema (OSTI)

    Andrei Seryi

    2010-01-08T23:59:59.000Z

    Plasma wakefield acceleration is one of the most promising approaches to advancing accelerator technology. This approach offers a potential 1,000-fold or more increase in acceleration over a given distance, compared to existing accelerators.  FACET, enabled by the Recovery Act funds, will study plasma acceleration, using short, intense pulses of electrons and positrons. In this lecture, the physics of plasma acceleration and features of FACET will be presented.  

  5. Degradation mechanisms and accelerated testing in PEM fuel cells

    SciTech Connect (OSTI)

    Borup, Rodney L [Los Alamos National Laboratory; Mukundan, Rangachary [Los Alamos National Laboratory

    2010-01-01T23:59:59.000Z

    The durability of PEM fuel cells is a major barrier to the commercialization of these systems for stationary and transportation power applications. Although there has been recent progress in improving durability, further improvements are needed to meet the commercialization targets. Past improvements have largely been made possible because of the fundamental understanding of the underlying degradation mechanisms. By investigating component and cell degradation modes; defining the fundamental degradation mechanisms of components and component interactions new materials can be designed to improve durability. Various factors have been shown to affect the useful life of PEM fuel cells. Other issues arise from component optimization. Operational conditions (such as impurities in either the fuel and oxidant stream), cell environment, temperature (including subfreezing exposure), pressure, current, voltage, etc.; or transient versus continuous operation, including start-up and shutdown procedures, represent other factors that can affect cell performance and durability. The need for Accelerated Stress Tests (ASTs) can be quickly understood given the target lives for fuel cell systems: 5000 hours ({approx} 7 months) for automotive, and 40,000 hrs ({approx} 4.6 years) for stationary systems. Thus testing methods that enable more rapid screening of individual components to determine their durability characteristics, such as off-line environmental testing, are needed for evaluating new component durability in a reasonable turn-around time. This allows proposed improvements in a component to be evaluated rapidly and independently, subsequently allowing rapid advancement in PEM fuel cell durability. These tests are also crucial to developers in order to make sure that they do not sacrifice durability while making improvements in costs (e.g. lower platinum group metal [PGM] loading) and performance (e.g. thinner membrane or a GDL with better water management properties). To achieve a deeper understanding and improve PEM fuel cell durability LANL is conducting research to better define fuel cell component degradation mechanisms and correlate AST measurements to component in 'real-world' situations.

  6. Accelerated Testing Validation

    SciTech Connect (OSTI)

    Mukundan, Rangachary; James, Greg; Davey, John; Langlois, David; Torraco, Dennis; Yoon, Wonseok; Weber, Adam Z; Borup, Rodney L.

    2011-07-01T23:59:59.000Z

    The DOE Fuel Cell technical team recommended ASTs were performed on 2 different MEAs (designated P5 and HD6) from Ballard Power Systems. These MEAs were also incorporated into stacks and operated in fuel cell bus modules that were either operated in the field (three P5 buses) in Hamburg, or on an Orange county transit authority drive cycle in the laboratory (HD6 bus module). Qualitative agreement was found in the degradation mechanisms and rates observed in the AST and in the field. The HD6 based MEAs exhibited lower voltage degradation rates (due to catalyst corrosion) and slower membrane degradation rates in the field as reflected by their superior performance in the high potential hold and open-circuit potential AST tests. The quantitative correlation of the degradation rates will have to take into account the various stressors in the field including temperature, relative humidity, start/stops and voltage cycles.

  7. Phase Stable Net Acceleration of Electrons From a Two-Stage Optical Accelerator

    SciTech Connect (OSTI)

    Sears, Christopher M.S.; /SLAC /Munich, Max Planck Inst. Quantenopt.; Colby, Eric; England, R.J.; Ischebeck, Rasmus; McGuinness, Christopher; Nelson, Janice; Noble, Robert; Siemann, Robert H.; Spencer, James; Walz, Dieter; /SLAC; Plettner, Tomas; Byer, Robert L.; /Stanford U., Phys. Dept.

    2011-11-11T23:59:59.000Z

    In this article we demonstrate the net acceleration of relativistic electrons using a direct, in-vacuum interaction with a laser. In the experiment, an electron beam from a conventional accelerator is first energy modulated at optical frequencies in an inverse-free-electron-laser and bunched in a chicane. This is followed by a second stage optical accelerator to obtain net acceleration. The optical phase between accelerator stages is monitored and controlled in order to scan the accelerating phase and observe net acceleration and deceleration. Phase jitter measurements indicate control of the phase to {approx}13{sup o} allowing for stable net acceleration of electrons with lasers.

  8. Fresnel diffraction patterns as accelerating beams

    E-Print Network [OSTI]

    Zhang, Yiqi; Zheng, Huaibin; Wu, Zhenkun; Li, Yuanyuan; Lu, Keqing; Zhang, Yanpeng

    2013-01-01T23:59:59.000Z

    We demonstrate that beams originating from Fresnel diffraction patterns are self-accelerating in free space. In addition to accelerating and self-healing, they also exhibit parabolic deceleration property, which is in stark contrast to other accelerating beams. We find that the trajectory of Fresnel paraxial accelerating beams is similar to that of nonparaxial Weber beams. Decelerating and accelerating regions are separated by a critical propagation distance, at which no acceleration is present. During deceleration, the Fresnel diffraction beams undergo self-smoothing, in which oscillations of the diffracted waves gradually focus and smooth out at the critical distance.

  9. Hydrothermal flow systems in the Midcontinent Rift: Oxygen and hydrogen isotopic studies of the North Shore Volcanic Group and related hypabyssal sills, Minnesota

    SciTech Connect (OSTI)

    Park, Y.R.; Ripley, E.M. [Indiana Univ., Bloomington, IN (United States). Dept. of Geological Sciences] [Indiana Univ., Bloomington, IN (United States). Dept. of Geological Sciences

    1999-06-01T23:59:59.000Z

    Rift-related lavas of the North Shore Volcanic Group (NSVG) are intruded by plutonic rocks of the Duluth Complex along the unconformity between the NSVG and the underlying Proterozoic metasedimentary rocks (Animikie Group) and Archean volcano-sedimentary and plutonic rocks. Heat associated with the emplacement of the mafic intrusions generated fluid flow in the overlying plateau lavas. {delta}{sup 18}O values for whole rocks from the NSVG and hypabyssal sills range from 5.5 to 17.7{per_thousand} and 5.3 to 11.5{per_thousand}, respectively, and most values are higher than those considered normal for basaltic rocks (5.4 to 6.0{per_thousand}). In general, there is a positive correlation between whole rock {delta}{sup 18}O and water content, which suggests that elevated {delta}{sup 18}O values are related primarily to secondary mineral growth and isotopic exchange during hydrothermal alteration and metamorphism. {delta}{sup 18}O{sub H{sub 2}O} values computed from amygdule-filling minerals such as smectite, chlorite, and epidote found in low- to high-temperature metamorphic zones range from {approximately}{minus}1 to 6{per_thousand} with an average value of {approximately}3{per_thousand}. Smectite in the lower-grade zones gives computed {delta}D{sub H{sub 2}O} values between {minus}26 and {minus}83{per_thousand}, whereas epidote in the higher-grade zones gives {delta}D{sub H{sub 2}O} values of {minus}15 to 6{per_thousand}. Fluid isotopic compositions computed from epidote and smectite values are suggestive of the involvement of at least two fluids during the early stages of amygdule filling. Fluid {delta}D and {delta}{sup 18}O values determined from epidote at the higher metamorphic grades indicate that seawater dominated the deeper portions of the system where greenschist facies assemblages and elevated {delta}{sup 18}O values were produced in flow interiors, as well as margins. Smectite isotopic compositions suggest that meteoric water was predominant in the shallower portions of the system. The increase in {delta}{sup 18}O values of massive flow interiors with depth is interpreted as a result of rock interaction with a fluid of constant oxygen isotopic composition with increasing temperature. The stable isotopic data are supportive of previous suggestions that seawater was involved in the hydrothermal system associated with the Midcontinent Rift. Although the origin of the seawater remains problematic, it appears that marine incursions may have occurred during the late stages of Portage Lake volcanism, and periodically thereafter.

  10. Upgraded Coal Interest Group

    SciTech Connect (OSTI)

    Evan Hughes

    2009-01-08T23:59:59.000Z

    The Upgraded Coal Interest Group (UCIG) is an EPRI 'users group' that focuses on clean, low-cost options for coal-based power generation. The UCIG covers topics that involve (1) pre-combustion processes, (2) co-firing systems and fuels, and (3) reburn using coal-derived or biomass-derived fuels. The UCIG mission is to preserve and expand the economic use of coal for energy. By reducing the fuel costs and environmental impacts of coal-fired power generation, existing units become more cost effective and thus new units utilizing advanced combustion technologies are more likely to be coal-fired.

  11. Bell, group and tangle

    SciTech Connect (OSTI)

    Solomon, A. I., E-mail: a.i.solomon@open.ac.u [Open University, Department of Physics (United Kingdom)

    2010-03-15T23:59:59.000Z

    The 'Bell' of the title refers to bipartite Bell states, and their extensions to, for example, tripartite systems. The 'Group' of the title is the Braid Group in its various representations; while 'Tangle' refers to the property of entanglement which is present in both of these scenarios. The objective of this note is to explore the relation between Quantum Entanglement and Topological Links, and to show that the use of the language of entanglement in both cases is more than one of linguistic analogy.

  12. Physics Needs for Future Accelerators

    E-Print Network [OSTI]

    Lykken, J D

    2000-01-01T23:59:59.000Z

    Contents: 1. Prologomena to any meta future physics 1.1 Physics needs for building future accelerators 1.2 Physics needs for funding future accelerators 2. Physics questions for future accelerators 2.1 Crimes and misapprehensions 2.1.1 Organized religion 2.1.2 Feudalism 2.1.3 Trotsky was right 2.2 The Standard Model as an effective field theory 2.3 What is the scale of new physics? 2.4 What could be out there? 2.5 Model-independent conclusions 3. Future accelerators 3.1 What is the physics driving the LHC? 3.2 What is the physics driving the LC? 3.2.1 Higgs physics is golden 3.2.2 LHC won't be sufficient to unravel the new physics as the TeV scale 3.2.3 LC precision measurements can pin down new physics scales 3.3 Why a Neutrino Factory? 3.4 Pushing the energy frontier

  13. Petawatt pulsed-power accelerator

    DOE Patents [OSTI]

    Stygar, William A. (Albuquerque, NM); Cuneo, Michael E. (Albuquerque, NM); Headley, Daniel I. (Albuquerque, NM); Ives, Harry C. (Albuquerque, NM); Ives, legal representative; Berry Cottrell (Albuquerque, NM); Leeper, Ramon J. (Albuquerque, NM); Mazarakis, Michael G. (Albuquerque, NM); Olson, Craig L. (Albuquerque, NM); Porter, John L. (Sandia Park, NM); Wagoner; Tim C. (Albuquerque, NM)

    2010-03-16T23:59:59.000Z

    A petawatt pulsed-power accelerator can be driven by various types of electrical-pulse generators, including conventional Marx generators and linear-transformer drivers. The pulsed-power accelerator can be configured to drive an electrical load from one- or two-sides. Various types of loads can be driven; for example, the accelerator can be used to drive a high-current z-pinch load. When driven by slow-pulse generators (e.g., conventional Marx generators), the accelerator comprises an oil section comprising at least one pulse-generator level having a plurality of pulse generators; a water section comprising a pulse-forming circuit for each pulse generator and a level of monolithic triplate radial-transmission-line impedance transformers, that have variable impedance profiles, for each pulse-generator level; and a vacuum section comprising triplate magnetically insulated transmission lines that feed an electrical load. When driven by LTD generators or other fast-pulse generators, the need for the pulse-forming circuits in the water section can be eliminated.

  14. THE RADIOLOGICAL RESEARCH ACCELERATOR FACILITY

    E-Print Network [OSTI]

    175 THE RADIOLOGICAL RESEARCH ACCELERATOR FACILITY #12;176 #12;177 THE RADIOLOGICAL RESEARCH the microbeam and the track-segment facilities have been utilized in various investigations. Table 1 lists-segment facility. Samples are treated with graded doses of radical scavengers to observe changes in the cluster

  15. Accelerating Multimedia with Enhanced Microprocessors

    E-Print Network [OSTI]

    Lee, Ruby B.

    Accelerating Multimedia with Enhanced Microprocessors A minimalistic set of multimedia instructions introduced into PA-RISC microprocessors implements SIMD-MIMD parallelism with insignificant changes to the underlying microprocessor. Thus, a software video decoder attains MPEG video and audio decom- pression

  16. Accelerators for Intensity Frontier Research

    SciTech Connect (OSTI)

    Derwent, Paul; /Fermilab

    2012-05-11T23:59:59.000Z

    In 2008, the Particle Physics Project Prioritization Panel identified three frontiers for research in high energy physics, the Energy Frontier, the Intensity Frontier, and the Cosmic Frontier. In this paper, I will describe how Fermilab is configuring and upgrading the accelerator complex, prior to the development of Project X, in support of the Intensity Frontier.

  17. Physics Needs for Future Accelerators

    E-Print Network [OSTI]

    Joseph D. Lykken

    2000-01-30T23:59:59.000Z

    Contents: 1. Prologomena to any meta future physics 1.1 Physics needs for building future accelerators 1.2 Physics needs for funding future accelerators 2. Physics questions for future accelerators 2.1 Crimes and misapprehensions 2.1.1 Organized religion 2.1.2 Feudalism 2.1.3 Trotsky was right 2.2 The Standard Model as an effective field theory 2.3 What is the scale of new physics? 2.4 What could be out there? 2.5 Model-independent conclusions 3. Future accelerators 3.1 What is the physics driving the LHC? 3.2 What is the physics driving the LC? 3.2.1 Higgs physics is golden 3.2.2 LHC won't be sufficient to unravel the new physics as the TeV scale 3.2.3 LC precision measurements can pin down new physics scales 3.3 Why a Neutrino Factory? 3.4 Pushing the energy frontier

  18. Thomas Jefferson National Accelerator Facility

    SciTech Connect (OSTI)

    Joseph Grames, Douglas Higinbotham, Hugh Montgomery

    2010-09-01T23:59:59.000Z

    The Thomas Jefferson National Accelerator Facility (Jefferson Lab) in Newport News, Virginia, USA, is one of ten national laboratories under the aegis of the Office of Science of the U.S. Department of Energy (DOE). It is managed and operated by Jefferson Science Associates, LLC. The primary facility at Jefferson Lab is the Continuous Electron Beam Accelerator Facility (CEBAF) as shown in an aerial photograph in Figure 1. Jefferson Lab was created in 1984 as CEBAF and started operations for physics in 1995. The accelerator uses superconducting radio-frequency (srf) techniques to generate high-quality beams of electrons with high-intensity, well-controlled polarization. The technology has enabled ancillary facilities to be created. The CEBAF facility is used by an international user community of more than 1200 physicists for a program of exploration and study of nuclear, hadronic matter, the strong interaction and quantum chromodynamics. Additionally, the exceptional quality of the beams facilitates studies of the fundamental symmetries of nature, which complement those of atomic physics on the one hand and of high-energy particle physics on the other. The facility is in the midst of a project to double the energy of the facility and to enhance and expand its experimental facilities. Studies are also pursued with a Free-Electron Laser produced by an energy-recovering linear accelerator.

  19. High Performance Outdoor Lighting Accelerator

    Broader source: Energy.gov [DOE]

    Hosted by the U.S. Department of Energy (DOE)’s Weatherization and Intergovernmental Programs Office (WIPO), this webinar covered the expansion of the Better Buildings platform to include the newest initiative for the public sector: the High Performance Outdoor Lighting Accelerator (HPOLA).

  20. Cost and Performance Report Accelerated Site Technology Deployment Program

    SciTech Connect (OSTI)

    P. S. Morris

    2002-05-01T23:59:59.000Z

    The U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Operations Office (NNSA/NV) Environmental Restoration Division (ERD) Industrial Sites Project Deactivation and Decommissioning (D and D) source group has limited budget and is constantly searching for new technologies to reduce programmatic costs. Partnering with the DOE Office of Science and Technology Deactivation and Decommissioning Focus Area (DDFA) reduces NNSA/NV programmatic risk and encourages accelerated deployment of potentially beneficial technologies to the Nevada Test Site (NTS).