Powered by Deep Web Technologies
Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Global horizontal irradiance clear sky models : implementation and analysis.  

SciTech Connect (OSTI)

Clear sky models estimate the terrestrial solar radiation under a cloudless sky as a function of the solar elevation angle, site altitude, aerosol concentration, water vapor, and various atmospheric conditions. This report provides an overview of a number of global horizontal irradiance (GHI) clear sky models from very simple to complex. Validation of clear-sky models requires comparison of model results to measured irradiance during clear-sky periods. To facilitate validation, we present a new algorithm for automatically identifying clear-sky periods in a time series of GHI measurements. We evaluate the performance of selected clear-sky models using measured data from 30 different sites, totaling about 300 site-years of data. We analyze the variation of these errors across time and location. In terms of error averaged over all locations and times, we found that complex models that correctly account for all the atmospheric parameters are slightly more accurate than other models, but, primarily at low elevations, comparable accuracy can be obtained from some simpler models. However, simpler models often exhibit errors that vary with time of day and season, whereas the errors for complex models vary less over time.

Stein, Joshua S.; Hansen, Clifford W.; Reno, Matthew J.

2012-03-01T23:59:59.000Z

2

Horizontal modular dry irradiated fuel storage system  

DOE Patents [OSTI]

A horizontal, modular, dry, irradiated fuel storage system (10) includes a thin-walled canister (12) for containing irradiated fuel assemblies (20), which canister (12) can be positioned in a transfer cask (14) and transported in a horizontal manner from a fuel storage pool (18), to an intermediate-term storage facility. The storage system (10) includes a plurality of dry storage modules (26) which accept the canister (12) from the transfer cask (14) and provide for appropriate shielding about the canister (12). Each module (26) also provides for air cooling of the canister (12) to remove the decay heat of the irradiated fuel assemblies (20). The modules (26) can be interlocked so that each module (26) gains additional shielding from the next adjacent module (26). Hydraulic rams (30) are provided for inserting and removing the canisters (12) from the modules (26).

Fischer, Larry E. (Los Gatos, CA); McInnes, Ian D. (San Jose, CA); Massey, John V. (San Jose, CA)

1988-01-01T23:59:59.000Z

3

Horizontal stirring in the global ocean  

E-Print Network [OSTI]

Horizontal mixing and the distribution of coherent structures in the global ocean are analyzed using Finite-Size Lyapunov Exponents (FSLE), computed for the surface velocity field derived from the Ocean general circulation model For the Earth Simulator (OFES). FSLEs measure horizontal stirring and dispersion; additionally, the transport barriers which organize the oceanic flow can roughly be identified with the ridges of the FSLE field. We have performed a detailed statistical study, particularizing for the behaviour of the two hemispheres and different ocean basins. The computed Probability Distributions Functions (PDFs) of FSLE are broad and asymmetric. Horizontal mixing is generally more active in the northern hemisphere than in the southern one. Nevertheless the Southern Ocean is the most active ocean, and the Pacific the less active one. A striking result is that the main currents can be classified in two 'activity classes': Western Boundary Currents, which have broad PDFs with large FSLE values, and Eas...

Hernández-Carrasco, I; Hernández-García, E; Turiel, A

2011-01-01T23:59:59.000Z

4

apres irradiation globale: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

necessary for the evaluation of global irradiance on inclined surface which is needed for photovoltaic Boyer, Edmond 7 Caractristiques lectriques de diodes Au-Si(N) ralises aprs...

5

Geiger M., Diabat L., Mnard L., Wald L., 2002. A web service for controlling the quality of measurements of global solar irradiation. Solar Energy, Vol. 73, No 6, pp. 475-480  

E-Print Network [OSTI]

sensitive sensors measure the downward solar radiation flux on a horizontal surface during a given time of measurements of global solar irradiation. Solar Energy, Vol. 73, No 6, pp. 475-480 Copyright Ecole des Mines de Paris -Armines - UFAE 1 A WEB SERVICE FOR CONTROLLING THE QUALITY OF MEASUREMENTS OF GLOBAL SOLAR

Paris-Sud XI, Université de

6

Simple solar spectral model for direct and diffuse irradiance on horizontal and tilted planes at the earth's surface for cloudless atmospheres  

SciTech Connect (OSTI)

A new, simple model for calculating clear-sky direct and diffuse spectral irradiance on horizontal and tilted surfaces is presented. The model is based on previously reported simple algorithms and on comparisons with rigorous radiative transfer calculations and limited outdoor measurements. Equations for direct normal irradiance are outlined; and include: Raleigh scattering; aerosol scattering and absorption; water vapor absorption; and ozone and uniformly mixed gas absorption. Inputs to the model include solar zenith angle, collector tilt angle, atmospheric turbidity, amount of ozone and precipitable water vapor, surface pressure, and ground albedo. The model calculates terrestrial spectra from 0.3 to 4.0 ..mu..m with approximately 10 nm resolution. A major goal of this work is to provide researchers with the capability to calculate spectral irradiance for different atmospheric conditions and different collector geometries using microcomputers. A listing of the computer program is provided.

Bird, R.; Riordan, C.

1984-12-01T23:59:59.000Z

7

24-hours ahead global irradiation forecasting using Multi-Layer Cyril Voyant1*  

E-Print Network [OSTI]

; it is shown that the most relevant is based on a multi- output MLP using endogenous and exogenous input data ahead. In the case of solar plants, the driving factor is the global solar irradiation (sum of direct and diffuse solar radiation projected on a plane (Wh/m²)). This paper focuses on the 24-hours ahead forecast

Paris-Sud XI, Université de

8

Response of precipitation extremes to idealized global warming in an aqua-planet climate model: Towards robust projection across different horizontal resolutions  

SciTech Connect (OSTI)

Current climate models produce quite heterogeneous projections for the responses of precipitation extremes to future climate change. To help understand the range of projections from multimodel ensembles, a series of idealized 'aquaplanet' Atmospheric General Circulation Model (AGCM) runs have been performed with the Community Atmosphere Model CAM3. These runs have been analysed to identify the effects of horizontal resolution on precipitation extreme projections under two simple global warming scenarios. We adopt the aquaplanet framework for our simulations to remove any sensitivity to the spatial resolution of external inputs and to focus on the roles of model physics and dynamics. Results show that a uniform increase of sea surface temperature (SST) and an increase of low-to-high latitude SST gradient both lead to increase of precipitation and precipitation extremes for most latitudes. The perturbed SSTs generally have stronger impacts on precipitation extremes than on mean precipitation. Horizontal model resolution strongly affects the global warming signals in the extreme precipitation in tropical and subtropical regions but not in high latitude regions. This study illustrates that the effects of horizontal resolution have to be taken into account to develop more robust projections of precipitation extremes.

Li, F.; Collins, W.D.; Wehner, M.F.; Williamson, D.L.; Olson, J.G.

2011-04-15T23:59:59.000Z

9

Could the Earth's surface Ultraviolet irradiance be blamed for the global warming? A new effect may exist  

E-Print Network [OSTI]

Whether natural factors could interpret the rise of the Earth's surface temperature is still controversial. Though numerous recent researches have reported apparent correlations between solar activity and the Earth's climate, solar activity has encountered a big problem when describing the rapid global warming after 1970s. Our investigation shows the good positive correlations between the Earth's surface Ultraviolet irradiance (280-400 nm) and the Earth's surface temperature both in temporal and spatial variations by analyzing the global surface Ultraviolet irradiance (280-400 nm) and global surface temperature data from 1980-1999. The rise of CO$_2$ cannot interpret the good positive correlations, and we could even get an opposite result to the good correlations when employing the rise of CO$_2$ to describe the relation between them. Based on the good positive correlations, we suggest a new effect, named "Highly Excited Water Vapor" (HEWV) effect, which can interpret how the Sun influences the Earth's surfac...

Chen, Jilong; Zhao, Juan; Zheng, Yujun

2014-01-01T23:59:59.000Z

10

Estimation of height-dependent solar irradiation and application to the solar climate of Iran  

SciTech Connect (OSTI)

An explicitly height-dependent model has been used to estimate the solar irradiation over Iran which has a vast range of altitudes. The parameters of the model have been chosen on general grounds and not by parameters best fitting to any of the available measured irradiation data in Iran. The estimated global solar irradiation on the horizontal surface shows a very good agreement (4.1% deviation) with the 17-year long pyranometric measurements in Tehran, and also, is in good agreement with other, shorter available measured data. The entire data base of the Iranian meteorological stations have been used to establish a simple relation between the sunshine duration records and the cloud cover reports which can be utilized in solar energy estimations for sites with no sunshine duration recorders. Clear sky maps of Iran for direct solar irradiation on tracking, horizontal, and south-facing vertical planes are presented. The global solar irradiation map for horizontal surface with cloudiness is zoned into four irradiation zones. In about four-fifths of the land in Iran, the annual-mean daily global solar irradiation on horizontal surface ranges from 4.5 to 5.4 kWh/m[sup 2].

Samimi, J. (Sharif Univ of Technology, Tehran (Iran, Islamic Republic of))

1994-05-01T23:59:59.000Z

11

A NEW HIGH FREQUENCY GLOBAL-TO-DIRECT IRRADIANCE CONVERSION METHODOLOGY  

E-Print Network [OSTI]

, Navarra (Spain) Abstract In order to accurately simulate the behavior of a solar thermal power plant will improve results of solar thermal power plants simulations. Keywords: Direct Normal Irradiance (DNI by knowing this information with accuracy, it will be possible to predict the solar thermal power plant

Paris-Sud XI, Université de

12

Comparison of Direct Normal Irradiance Derived from Silicon and Thermopile Global Hemispherical Radiation Detectors: Preprint  

SciTech Connect (OSTI)

Concentrating solar applications utilize direct normal irradiance (DNI) radiation, a measurement rarely available. The solar concentrator industry has begun to deploy numerous measurement stations to prospect for suitable system deployment sites. Rotating shadowband radiometers (RSR) using silicon photodiodes as detectors are typically deployed. This paper compares direct beam estimates from RSR to a total hemispherical measuring radiometer (SPN1) multiple fast thermopiles. These detectors simultaneously measure total and diffuse radiation from which DNI can be computed. Both the SPN1 and RSR-derived DNI are compared to DNI measured with thermopile pyrheliometers. Our comparison shows that the SPN1 radiometer DNI estimated uncertainty is somewhat greater than, and on the same order as, the RSR DNI estimates for DNI magnitudes useful to concentrator technologies.

Myers, D. R.

2010-01-01T23:59:59.000Z

13

Global  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun with Big Sky LearningGet Assistance GetGiant ProteaseGlass andT.2 -Global

14

Horizontal well IPR calculations  

SciTech Connect (OSTI)

This paper presents the calculation of near-wellbore skin and non-Darcy flow coefficient for horizontal wells based on whether the well is drilled in an underbalanced or overbalanced condition, whether the well is completed openhole, with a slotted liner, or cased, and on the number of shots per foot and phasing for cased wells. The inclusion of mechanical skin and the non-Darcy flow coefficient in previously published horizontal well equations is presented and a comparison between these equations is given. In addition, both analytical and numerical solutions for horizontal wells with skin and non-Darcy flow are presented for comparison.

Thomas, L.K.; Todd, B.J.; Evans, C.E.; Pierson, R.G.

1996-12-31T23:59:59.000Z

15

Could the Earth's surface Ultraviolet irradiance be blamed for the global warming? (II) ----Ozone layer depth reconstruction via HEWV effect  

E-Print Network [OSTI]

It is suggested by Chen {\\it et al.} that the Earth's surface Ultraviolet irradiance ($280-400$ nm) could influence the Earth's surface temperature variation by "Highly Excited Water Vapor" (HEWV) effect. In this manuscript, we reconstruct the developing history of the ozone layer depth variation from 1860 to 2011 based on the HEWV effect. It is shown that the reconstructed ozone layer depth variation correlates with the observational variation from 1958 to 2005 very well ($R=0.8422$, $P>99.9\\%$). From this reconstruction, we may limit the spectra band of the surface Ultraviolet irradiance referred in HEWV effect to Ultraviolet B ($280-320$ nm).

Chen, Jilong; Zheng, Yujun

2014-01-01T23:59:59.000Z

16

The effect of surface irradiance on the absorption spectrum of chromophoric dissolved organic matter in the global ocean  

E-Print Network [OSTI]

.2 mm), is responsible for nearly 90% of ultraviolet (UV) radiation attenuation in the global ocean matter in the global ocean Chantal M. Swan a,n , Norman B. Nelson a , David A. Siegel a,b , Tihomir S to better assess the impact of CDOM on surface ocean photochemistry and remote sensing of ocean color

Siegel, David A.

17

Horizontal Advanced Tensiometer  

DOE Patents [OSTI]

An horizontal advanced tensiometer is described that allows the monitoring of the water pressure of soil positions, particularly beneath objects or materials that inhibit the use of previous monitoring wells. The tensiometer includes a porous cup, a pressure transducer (with an attached gasket device), an adaptive chamber, at least one outer guide tube which allows access to the desired horizontal position, a transducer wire, a data logger and preferably an inner guide tube and a specialized joint which provides pressure on the inner guide tube to maintain the seal between the gasket of the transducer and the adaptive chamber.

Hubbell, Joel M.; Sisson, James B.

2004-06-22T23:59:59.000Z

18

Nuclear component horizontal seismic restraint  

DOE Patents [OSTI]

A nuclear component horizontal seismic restraint. Small gaps limit horizontal displacement of components during a seismic occurrence and therefore reduce dynamic loadings on the free lower end. The reactor vessel and reactor guard vessel use thicker section roll-forged rings welded between the vessel straight shell sections and the bottom hemispherical head sections. The inside of the reactor guard vessel ring forging contains local vertical dovetail slots and upper ledge pockets to mount and retain field fitted and installed blocks. As an option, the horizontal displacement of the reactor vessel core support cone can be limited by including shop fitted/installed local blocks in opposing alignment with the reactor vessel forged ring. Beams embedded in the wall of the reactor building protrude into apertures in the thermal insulation shell adjacent the reactor guard vessel ring and have motion limit blocks attached thereto to provide to a predetermined clearance between the blocks and reactor guard vessel ring.

Snyder, Glenn J. (Lynchburg, VA)

1988-01-01T23:59:59.000Z

19

Results of the Second Diffuse Horizontal Irradiance IOP  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared0 Resource Program September 2010 B O N N E V I L LResponseResults

20

Industry survey for horizontal wells. Final report  

SciTech Connect (OSTI)

An international survey of horizontal environmental wells was performed during May and June of 1993. The purpose of the survey was to provide the environmental industry with an inventory of horizontal environmental wells and information pertaining to the extent of the use of horizontal environmental wells, the variety of horizontal environmental well applications, the types of geologic and hydrogeologic conditions within which horizontal environmental wells have been installed, and the companies that perform horizontal environmental well installations. Other information, such as the cost of horizontal environmental well installations and the results of tests performed on the wells, is not complete but is provided as general information with the caveat that the information should not be used to compare drilling companies. The result of the survey is a catalogue of horizontal environmental wells that are categorized by the objective or use of the wells, the vertical depth of the wells, and the drilling company contracted to install the wells.

Wilson, D.D.; Kaback, D.S. [CDM Federal Programs Corp., Denver, CO (United States); Denhan, M.E. [Westinghouse Savannah River Co., Aiken, SC (United States); Watkins, D. [CDM Federal Programs Corp., Aiken, SC (United States)

1993-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

E-Print Network 3.0 - apres irradiation neutron-gamma Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

17 INTEGRATION OF HELIOCLIM-1 DATABASE INTO PV-GIS TO ESTIMATE SOLAR ELECTRICITY POTENTIAL IN AFRICA Summary: for computing high resolution database of global horizontal...

22

Global Statistics  

E-Print Network [OSTI]

1996). Globalization in Question: International Economy andGlobalization; Justice; Poverty; Underground Economy; United

Crow, Ben D

2006-01-01T23:59:59.000Z

23

IRRADIATION EXPERIMENTS &  

E-Print Network [OSTI]

IRRADIATION EXPERIMENTS & FACILITIES AT BNL: BLIP & NSLS II Peter Wanderer Superconducting Magnet). Current user: LBNE ­ materials for Project X. · Long Baseline Neutrino Experiment ­ Abandoned gold mine

McDonald, Kirk

24

3, 895959, 2006 Irradiance and  

E-Print Network [OSTI]

and corals. However, the contribution of benthic communities to the primary production of the global coastal energy source fueling marine primary prBGD 3, 895­959, 2006 Irradiance and primary production in the coastal ocean J.-P. Gattuso et al

Paris-Sud XI, Université de

25

Bakken shale typifies horizontal drilling success  

SciTech Connect (OSTI)

Given the favorable production response that has been obtained from horizontal drilling in vertical- fractured reservoirs such as the Bakken shale and, more recently, the Austin chalk, industry interest in this technology has mushroomed in the U.S. Indeed, it is difficult to find a good-sized oil company these days that is not involved in a horizontal drilling project or is giving it serious consideration. In response to growing evidence of successful field applications, the realization is dawning on the investment community that horizontal drilling represents a significant technological development with positive implications for both the exploration and production business, and the oilfield services industry.

Leibman, P.R. (Petrie Parkman and Co., Denver, CO (US))

1990-12-01T23:59:59.000Z

26

Horizontal gene transfer in Bacteroides fragilis   

E-Print Network [OSTI]

Horizontal gene transfer (HGT) is one of the man driving forces of evolution in prokaryotes, and can also promote within-strain variation of bacterial species. The genomes of three previously sequenced Bacteroides fragilis ...

Jobling, Kelly Louise

2014-11-27T23:59:59.000Z

27

Particle Impact Damping in the Horizontal Plane  

E-Print Network [OSTI]

Particle impact damping is measured for a cantilevered beam vibrating freely in the horizontal plane. Several particle configurations are investigated beginning with a single particle and progressing to multiple layers of particles. The effects...

Witt, Bryan

2012-07-16T23:59:59.000Z

28

Natural Gas Horizontal Well Control Act (West Virginia)  

Broader source: Energy.gov [DOE]

The Natural Gas Horizontal Well Control Act regulates the construction, alteration, enlargement, abandonment and removal of horizontal wells and associated water and wastewater use and storage. The...

29

Global Statistics  

E-Print Network [OSTI]

of Globalization: Statistics Weiss, L. (1997). "of Globalization: Statistics Milanovic, B. (1999). Truethe focus of global statistics, particularly in relation to

Crow, Ben D

2006-01-01T23:59:59.000Z

30

Two-phase flow in horizontal wells  

SciTech Connect (OSTI)

Flow in horizontal wells and two-phase flow interaction with the reservoir were investigated experimentally and theoretically. Two-phase flow behavior has been recognized as one of the most important problems in production engineering. The authors designed and constructed a new test facility suitable for acquiring data on the relationship between pressure drop and liquid holdup along the well and fluid influx from the reservoir. For the theoretical work, an initial model was proposed to describe the flow behavior in a horizontal well configuration. The model uses the inflow-performance-relationship (IPR) approach and empirical correlations or mechanistic models for wellbore hydraulics. Although good agreement was found between the model and experimental data, a new IPR apart from the extension of Darcy`s law must be investigated extensively to aid in the proper design of horizontal wells.

Ihara, Masaru [Japan National Oil Corp., Chiba (Japan); Yanai, Koji [Nippon Kokan Corp., Yokohama (Japan); Yanai, Koji

1995-11-01T23:59:59.000Z

31

Tables in Context: Integrating Horizontal Displays with  

E-Print Network [OSTI]

design challenges for tabletop interfaces: integrating access to public and private information, managing a cooperative gesture to organize digital documents on an interactive table. Our tabletop interface designTables in Context: Integrating Horizontal Displays with Ubicomp Environments Abstract Our work

Klemmer, Scott

32

Wayne field: A horizontal drilling case study  

SciTech Connect (OSTI)

Beginning in the spring of 1994, studies of Wayne field located on the northeastern flank of the Williston Basin were initiated to determine the feasibility of using horizontal drilling to increase recoverable reserves in the field. The Wayne subinterval is one of several shoaling-upwards cycles within the Mission Canyon Formation of the Mississippian Madison Group. The reservoir pay averages 24% porosity, 100 millidarcys permeability, and 50% water saturation. Vertical wells, since field discovery in 1957, typically IP for 70 bopd and 20% water with a rapid decline within a few months to 10 bopd and 90% water. This type of well performance is characteristic of severe water coning for which horizontal development can help to minimize. In late 1994 and early 1995 the Ballantyne Hedges No.7H and GeoResources O. Fossum No.H1 were drilled. The wells recorded IP`s of 280 bopd/5 bwpd and 390 bopd/80 bwpd respectively. After six months of production both wells stabilized at approximately 110 bopd with a 35% water cut. Projections indicate that each horizontal well will recover 250,000 bbls of oil as compared to 115,000 bbls for an average vertical well and will do so in half the time. These early results provide a significant improvement over the vertical production and would seem to be reducing water coning. Three more horizontal wells are planned for the fourth quarter of 1995.

Jennings, J.B. [GeoResources, Inc., Williston, ND (United States); Johnson, R.P. [Harris, Brown, & Kiemer, Inc., Bismarck, ND (United States)

1996-06-01T23:59:59.000Z

33

Safer Food with Irradiation  

E-Print Network [OSTI]

This publication answers questions about food irradiation and how it helps prevent foodborne illnesses. Included are explanations of how irradiation works and its benefits. Irradiation is a safe method of preserving food quality and ensuring its...

Thompson, Britta; Vestal, Andy; Van Laanen, Peggy

2003-01-21T23:59:59.000Z

34

Flow mapping for an ESS horizontal target  

SciTech Connect (OSTI)

In the target of the European spallation neutron source (ESS), the beam line is horizontal and the mercury is fully forced by a pump in a parallel channel geometry. The top front of the assembly is a hemicylindrical wall, where the beam enters and is thus called a window. The main body is partitioned by a horizontal separation plate into the upper and the lower flow channels. The target liquid flows in the lower channel to the window region, turns there, and flows out in the upper channel. A thermal-hydraulic study is under way to investigate the general behavior of the flow in this configuration. The present experimental work is the first step of an effort to validate computer codes. The model used in this investigation is two-dimensional and uses water.

Takeda, Y.; Kikura, H.; Taishi, T. [Paul Scherrer Institute, Villigen (Switzerland)

1997-12-01T23:59:59.000Z

35

A performance correlation of horizontal solar heaters  

E-Print Network [OSTI]

A PERFORMANCE CORRELATION OF HORIZONTAL SOLAR HEATERS A Thesis by WILFORD HUGO GOPFFARTH Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE August 1964... Major Subject: Chemical Engineering ABSTRACT The purpose of this work was to determine design parameters for flat plastic covered solar collectors. First, the transmittance ? absorp- tion product as a function of the angle of incidence was determined...

Gopffarth, Wilford Hugo

1964-01-01T23:59:59.000Z

36

Economic viability of multiple-lateral horizontal wells  

E-Print Network [OSTI]

Horizontal wells are gaining popularity throughout the petroleum industry as a means to increase well productivity and enhance incremental economics. Horizontal wells provide greater reservoir exposure and are useful in intersecting additional pay...

Smith, Christopher Jason

1995-01-01T23:59:59.000Z

37

Sidewall containment of liquid metal with horizontal alternating magnetic fields  

DOE Patents [OSTI]

An apparatus is disclosed for confining molten metal with a horizontal alternating magnetic field. In particular, this invention employs a magnet that can produce a horizontal alternating magnetic field to confine a molten metal at the edges of parallel horizontal rollers as a solid metal sheet is cast by counter-rotation of the rollers. 19 figs.

Praeg, W.F.

1995-01-31T23:59:59.000Z

38

University of Texas Panamerican (UTPA): Solar Radiation Lab (SRL); Edinburg, Texas (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

This measurement station monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location.

Ramos, J.; Andreas, A.

39

Oak Ridge National Laboratory (ORNL); Rotating Shadowband Radiometer (RSR); Oak Ridge, Tennessee (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

This measurement station monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location.

Maxey, C.; Andreas, A.

40

Generation of large-scale winds in horizontally anisotropic convection  

E-Print Network [OSTI]

We simulate three-dimensional, horizontally periodic Rayleigh-B\\'enard convection between free-slip horizontal plates, rotating about a horizontal axis. When both the temperature difference between the plates and the rotation rate are sufficiently large, a strong horizontal wind is generated that is perpendicular to both the rotation vector and the gravity vector. The wind is turbulent, large-scale, and vertically sheared. Horizontal anisotropy, engendered here by rotation, appears necessary for such wind generation. Most of the kinetic energy of the flow resides in the wind, and the vertical turbulent heat flux is much lower on average than when there is no wind.

von Hardenberg, J; Provenzale, A; Spiegel, E A

2015-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Horizontal air trajectories in a geostrophic field with uniform horizontal shear  

E-Print Network [OSTI]

balloon A careful analysis of horizontal sir trgectories hse been made in s proJect by the Deyarheent of %%acrology, University of Oalifornts at Los Angeles by ~son P6g. The equations of horizontal, nonviscous motion were integrated numeric~ by a... Coriolis force (d3xcctad to the r3ght) is less tJ~ the presnue @radiant force, and the parhicle is accelerated In tbe direction cf the lavhcz force. Tn the second case, tbe velocity is @roster +ban tbe gecstrophie vclocity3 hence the Corlolis force...

Todsen, Marius

1956-01-01T23:59:59.000Z

42

Decline curve analysis for horizontal wells  

E-Print Network [OSTI]

support kept me from losing sight of my goals. Thanks to Sam Hou, Joseph Wang, Robert Liau, James Wang, and Shou for their company and in particular to Li Fan and Mrs. Shou-Lee Chang for their caring and delicious meals when I forgot my dinner. Thanks... Pressure (L/2xe= 0. 2) Composite Dimensionless Flow Rate Integral and Flow Rate Integral Derivative Functions Type Curve for an Infinite-Conductivity Horizontal Well Located in the Center of a Square Drainage Area, Producing at Constant Bottomhole...

Shih, Min-Yu

1994-01-01T23:59:59.000Z

43

Interphase transport in horizontal stratified cocurrent flow  

SciTech Connect (OSTI)

The problem of interfacial transport in cocurrent, horizontal stratified gas-liquid systems is considered. Local condensation heat transfer coefficients and interface shear stress were obtained from mass and force balances. Based on cocurrent stratified air-water flow data, the noncondensing interface shear stress was found to be a function of the relative velocity between the phases and the liquid fraction. Incorporated into Linehan's relation for condensing flow shear stress, the correlation was found to estimate the shear velocity for the condensation data considered. Local condensation heat transfer coefficients and gas absorption mass transfer coefficients were found to be directly proportional to the shear velocity.

Jensen, R.J.; Yuen, M.C.

1982-05-01T23:59:59.000Z

44

Bitumen production through a horizontal well  

SciTech Connect (OSTI)

This patent describes a method for thermal stimulation and production of a viscous hydrocarbon from a reservoir having a productive layer which retains the hydrocarbon until the latter is made flowable by contact with a hot stimulating medium. The method includes the steps of: forming a borehole having a substantially horizontal segment which transverses the productive layer, registering a well completion in the borehole which includes; an elongated perforate well liner, a fluid conduit extending through the liner and having a discharge end, and a well head at the liner upper end communicated with the fluid conduit, positioning a variable length flow diverter in the liner adjacent to the fluid conduit discharge end, whereby to define a quasi-barrier in the liner which is pervious to passage of the hot stimulating medium, and which divides the liner into injection and production segments respectively, heating the productive layer about the substantially horizontal segment of the elongated liner, introducing a pressurized stream of the hot stimulant through the fluid conduit and into the liner injection segment, and producing hydrocarbon emulsion which flows into the liner production segment.

Livesey, D.B.; Toma, P.

1987-02-03T23:59:59.000Z

45

Atmospheric Climate Model Experiments Performed at Multiple Horizontal Resolutions  

SciTech Connect (OSTI)

This report documents salient features of version 3.3 of the Community Atmosphere Model (CAM3.3) and of three climate simulations in which the resolution of its latitude-longitude grid was systematically increased. For all these simulations of global atmospheric climate during the period 1980-1999, observed monthly ocean surface temperatures and sea ice extents were prescribed according to standard Atmospheric Model Intercomparison Project (AMIP) values. These CAM3.3 resolution experiments served as control runs for subsequent simulations of the climatic effects of agricultural irrigation, the focus of a Laboratory Directed Research and Development (LDRD) project. The CAM3.3 model was able to replicate basic features of the historical climate, although biases in a number of atmospheric variables were evident. Increasing horizontal resolution also generally failed to ameliorate the large-scale errors in most of the climate variables that could be compared with observations. A notable exception was the simulation of precipitation, which incrementally improved with increasing resolution, especially in regions where orography plays a central role in determining the local hydroclimate.

Phillips, T; Bala, G; Gleckler, P; Lobell, D; Mirin, A; Maxwell, R; Rotman, D

2007-12-21T23:59:59.000Z

46

Nonplanar fracture propagation from a horizontal wellbore: Experimental study  

SciTech Connect (OSTI)

This paper presents experimental results related to hydraulic fracturing of a horizontal well, specifically the nonplanar fracture geometries resulting from fracture initiation and propagation. Experiments were designed to investigate nonplanar fracture geometries. This paper discusses how these nonplanar fractures can be responsible for premature screenout and excessive treatment pressure when a horizontal well is hydraulically fractured. Reasons for unsuccessful hydraulic fracturing treatments of a horizontal well are presented and recommendations to ensure clear communication channels between the wellbore and the fracture are given.

Abass, H.H.; Hedayati, S.; Meadows, D.L.

1996-08-01T23:59:59.000Z

47

Water coning calculations for vertical and horizontal wells  

E-Print Network [OSTI]

Breakthrough Time WOR after Breakthrough RATE SENSITIVITY 8 12 13 16 WATER CONING CALCULATIONS FOR HIGH MOBILITY RATIOS . . 19 Method of Developing Correlations Correlations for a Vertical Well Correlations for a Horizontal Well Discussion 19 26... APPENDIX E: BASE CASE AND SIMULATION RUNS FOR HORIZONTAL WELLS 98 APPENDIX F: TEST CASES AND RESULTS FOR HORIZONTAL WELLS 100 APPENDIX G: ADDINGTON'S METHOD APPENDIX H: CALCULATION OF HEIGHT h~ APPENDIX I: BASE CASE AND SIMULATION RUN SUMMARY...

Yang, Weiping

1990-01-01T23:59:59.000Z

48

Application of horizontal wells in steeply dipping reservoirs.  

E-Print Network [OSTI]

??A three-dimensional reservoir simulation study is performed to evaluate the impact of horizontal well applications on oil recovery from steeply dipping reservoirs. The Provincia field,… (more)

Lopez Navarro, Jose David

2012-01-01T23:59:59.000Z

49

Study of natural convection heat transfer above a horizontal heated plate using a laser specklegram technique  

E-Print Network [OSTI]

flow from the horizontal isothermal plate. 15. Study of the effect of aspect ratio (AR) of the heated surface on the global Nusselt number for Ra = 104 50 NOMENCLATURE a distance between the test section and the second parabolic mirror (mm) b... plane of a CCD-camera (mm) h heat transfer coefficient. K Gladstone ? Dale constant for air ( m'/kg) . K, thermal conductivity of air ((tj)/m-'C) L Length of the test section measured along the optical axis m magnification of the second (parabolic...

Cheeti, Satish K.R.

1993-01-01T23:59:59.000Z

50

Acid Placement in Acid Jetting Treatments in Long Horizontal Wells  

E-Print Network [OSTI]

In the Middle East, extended reach horizontal wells (on the order of 25,000 feet of horizontal displacement) are commonly acid stimulated by jetting acid out of drill pipe. The acid is jetted onto the face of the openhole wellbore as the drill pipe...

Sasongko, Hari

2012-07-16T23:59:59.000Z

51

Steerable vertical to horizontal energy transducer for mobile robots  

DOE Patents [OSTI]

The present invention provides a steerable vertical to horizontal energy transducer for mobile robots that less complex and requires less power than two degree of freedom tilt mechanisms. The present invention comprises an end effector that, when mounted with a hopping actuator, translates along axis (typically vertical) actuation into combined vertical and horizontal motion. The end effector, or foot, mounts with an end of the actuator that moves toward the support surface (typically a floor or the earth). The foot is shaped so that the first contact with the support surface is off the axis of the actuator. Off-axis contact with the support surface generates an on-axis force (typically resulting in vertical motion) and a moment orthogonal to the axis. The moment initiates a horizontal tumbling motion, and tilts the actuator so that its axis is oriented with a horizontal component and continued actuation generates both vertical and horizontal force.

Spletzer, Barry L. (Albuquerque, NM); Fischer, Gary J. (Albuquerque, NM); Feddema, John T. (Albuquerque, NM)

2001-01-01T23:59:59.000Z

52

Yaw dynamics of horizontal axis wind turbines  

SciTech Connect (OSTI)

Designers of a horizontal axis wind turbine yaw mechanism are faced with a difficult decision. They know that if they elect to use a yaw- controlled rotor then the system will suffer increased initial cost and increased inherent maintenance and reliability problems. On the other hand, if they elect to allow the rotor to freely yaw they known they will have to account for unknown and random, though bounded, yaw rates. They will have a higher-risk design to trade-off against the potential for cost savings and reliability improvement. The risk of a yaw-free system could be minimized if methods were available for analyzing and understanding yaw behavior. The complexity of yaw behavior has, until recently, discouraged engineers from developing a complete yaw analysis method. The objectives of this work are to (1) provide a fundamental understanding of free-yaw mechanics and the design concepts most effective at eliminating yaw problems, and (2) provide tested design tools and guidelines for use by free-yaw wind systems manufacturers. The emphasis is on developing practical and sufficiently accurate design methods.

Hansen, A.C. (Utah Univ., Salt Lake City, UT (United States))

1992-05-01T23:59:59.000Z

53

Interphase transport in horizontal stratified cocurrent flow  

SciTech Connect (OSTI)

The problem of interfacial transport is cocurrent, horizontal stratified gas-liquid systems is considered. Local condensation heat transfer coefficients and interface shear stress were obtained from mass and force balances. These balances were based on gas phase pitot traverses at various streamwise locations. Laser anemometer measurements of liquid mean and rms fluctuation velocities were made at similar locations. The laser anemometer data supported the value for the interface shear velocity obtained by the gas phase force balance. Based on cocurrent stratified air-water flow data the noncondensing interface shear stress was found to be a function of the relative velocity betwen the phases and the liquid fraction. Incorporated into Linehan's relation for condensing flow shear stress, the correlation was found to estimate the shear velicity for the condensation data considered. Local condensation heat transfer coefficients and gas absorption mass transfer coefficients were found to be directly proportional ot the shear velocity. If the inner scales u. and /u. are substituted into Lamont's models for the interface mass transfer coefficient, many features of the present correlation for scalar transfer are predicted. The correlations for interfacial shear stress and scalar transport can be combined ot yield an interactive technique suitable for an engineering analysis of the interfacial heat, mass, and momentum transfer in a single driving force cocurrent system.

Jensen, R.J.

1982-01-01T23:59:59.000Z

54

Development of a Charged Particle Microbeam for Targeted and Single Particle Subcellular Irradiation  

SciTech Connect (OSTI)

The development of a charged particle microbeam for single particle, subcellular irradiations at the Massachusetts Institute of Technology Laboratory for Accelerator Beam Applications (MIT LABA) was initiated under this NEER aeard. The Microbeam apparatus makes use of a pre-existing electrostatic accelerator with a horizontal beam tube.

Yanch, Jacquelyn C.

2004-03-12T23:59:59.000Z

55

Horizontal oil well applications and oil recovery assessment. Volume 1: Success of horizontal well technology, Final report  

SciTech Connect (OSTI)

Horizontal technology has been applied in over 110 formations in the USA. Volume I of this study addresses the overall success of horizontal technology, especially in less-publicized formations, i.e., other than the Austin Chalk, Bakken, and Niobrara. Operators in the USA. and Canada were surveyed on a formation-by-formation basis by means of a questionnaire. Response data were received describing horizontal well projects in 58 formations in the USA. and 88 in Canada. Operators responses were analyzed for trends in technical and economic success based on lithology (clastics and carbonates) and resource type (light oil, heavy oil, and gas). The potential impact of horizontal technology on reserves was also estimated. A forecast of horizontal drilling activity over the next decade was developed.

Deskins, W.G.; McDonald, W.J.; Knoll, R.G.; Springer, S.J.

1995-03-01T23:59:59.000Z

56

ARM Multi-Filter Rotating Shadowband Radiometer (MFRSR): irradiances  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

The multifilter rotating shadowband radiometer (MFRSR) takes spectral measurements of direct normal, diffuse horizontal and total horizontal solar irradiances. These measurements are at nominal wavelengths of 415, 500, 615, 673, 870, and 940 nm. The measurements are made at a user-specified time interval, usually about one minute or less. The sampling rate for the Atmospheric Radiation Measurement (ARM) Climate Research Facility MFRSRs is 20 seconds. From such measurements, one may infer the atmosphere's optical depth at the wavelengths mentioned above. In turn, these optical depths may be used to derive information about the column abundances of ozone and water vapor (Michalsky et al. 1995), as well as aerosol (Michalsky et al. 1994) and other atmospheric constituents. A silicon detector is also part of the MFRSR. This detector provides a measure of the broadband direct normal, diffuse horizontal and total horizontal solar irradiances. A MFRSR head that is mounted to look vertically downward can measure upwelling spectral irradiances. In the ARM system, this instrument is called a multifilter radiometer (MFR). At the Southern Great Plains (SGP) there are two MFRs; one mounted at the 10-m height and the other at 25 m. At the North Slope of Alaska (NSA) sites, the MFRs are mounted at 10 m. MFRSR heads are also used to measure normal incidence radiation by mounting on a solar tracking device. These are referred to as normal incidence multi-filter radiometers (NIMFRs) and are located at the SGP and NSA sites. Another specialized use for the MFRSR is the narrow field of view (NFOV) instrument located at SGP. The NFOV is a ground-based radiometer (MFRSR head) that looks straight up.

Hodges, Gary

57

Fraced horizontal well shows potential of deep tight gas  

SciTech Connect (OSTI)

Successful completion of a multiple fraced, deep horizontal well demonstrated new techniques for producing tight gas sands. In Northwest Germany, Mobil Erdgas-Erdoel GmbH drilled, cased, and fraced the world`s deepest horizontal well in the ultra-tight Rotliegendes ``Main`` sand at 15,687 ft (4,783 m) true vertical depth. The multiple frac concept provides a cost-efficient method to economically produce significant gas resources in the ultra-tight Rotliegendes ``Main`` sand. Besides the satisfactory initial gas production rate, the well established several world records, including deepest horizontal well with multiple fracs, and proved this new technique to develop ultra-tight sands.

Schueler, S. [Mobil Erdgas-Erdoel GmbH, Celle (Germany); Santos, R. [Mobil Erdgas-Erdoel GmbH, Hamburg (Germany)

1996-01-08T23:59:59.000Z

58

Indoor and Outdoor Spectroradiometer Intercomparison for Spectral Irradiance Measurement  

SciTech Connect (OSTI)

This report details the global spectral irradiance intercomparison using spectroradiometers that was organized by the National Renewable Energy Laboratory's Solar Radiation Research Laboratory. The intercomparison was performed both indoors and outdoors on September 17, 2013. Five laboratories participated in the intercomparison using 10 spectroradiometers, and a coordinated measurement setup and a common platform were employed to compare spectral irradiances under both indoor and outdoor conditions. The intercomparison aimed to understand the performance of the different spectroradiometers and to share knowledge in making spectral irradiance measurements. This intercomparison was the first of its kind in the United States.

Habte, A.; Andreas, A.; Ottoson, L.; Gueymard, C.; Fedor, G.; Fowler, S.; Peterson, J.; Naranen, R.; Kobashi, T.; Akiyama, A.; Takagi, S.

2014-05-01T23:59:59.000Z

59

Simulation studies of waterflood performance with horizontal wells  

E-Print Network [OSTI]

Two-and three-dimensional simulation studies have been carried out to evaluate waterflood oil recovery in a 40-acre 5-spot pattern using horizontal and vertical well systems. The three-dimensional simulation results indicate that the parameters...

Ferreira, Horacio

1995-01-01T23:59:59.000Z

60

Optimization of fractured well performance of horizontal gas wells  

E-Print Network [OSTI]

In low-permeability gas reservoirs, horizontal wells have been used to increase the reservoir contact area, and hydraulic fracturing has been further extending the contact between wellbores and reservoirs. This thesis presents an approach...

Magalhaes, Fellipe Vieira

2009-06-02T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Horizontal non-contact slumping of flat glass  

E-Print Network [OSTI]

This paper continues the work of M. Akilian and A. Husseini on developing a noncontact glass slumping/shaping process. The shift from vertical slumping to horizontal slumping is implemented and various technologies required ...

Sung, Edward, S.M. Massachusetts Institute of Technology

2013-01-01T23:59:59.000Z

62

The time to reach pseudosteady-state in horizontal wells  

E-Print Network [OSTI]

Engineers need to estimate the expected productivity of horizontal wells. We need to know how long it takes to reach pseudosteady-state to accept that estimation. When all boundaries influence the pressure distribution in the drainage area...

Al-Kahtani, Abdulghafour

1998-01-01T23:59:59.000Z

63

Refrigerant forced-convection condensation inside horizontal tubes  

E-Print Network [OSTI]

Condensing heat transfer rates inside a horizontal tube were investigated -for large quality changes across the tube. The proposed correlation is a modification of the work of Rohsenow, Webber and Ling [29]. The result of ...

Bae, Soonhoon

1968-01-01T23:59:59.000Z

64

Horizontal Beam Tubes - HFIR Technical Parameters | ORNL Neutron...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Beam Tubes The reactor has four horizontal beam tubes that supply the neutrons to the neutron scattering instruments. Details for each beam tube and instrument can be found on...

65

Determination of Elastic Twist in Horizontal Axis Wind Turbines (HAWTs)  

SciTech Connect (OSTI)

This report presents the results of a project at the Alternative Energy Institute (AEI) which measured and calculated the elastic twist of three representative composite horizontal-axis blades: Carter 300, Gougeon ESI 54, and UTRC 8 kW.

Stoddard, F.; Nelson, V.; Starcher, K.; Andrews, B.

2006-06-01T23:59:59.000Z

66

Optimization of well length in waterflooding a five-spot pattern of horizontal wells  

E-Print Network [OSTI]

for the horizontal wells and provide a good return on investment. Horizontal Wells in Waterflood Pr t A worldwide interest exists today in drilling horizontal wells to increase productivity, Horizontal wells can be used in any phase of reservoir recovery... efficiency7. Several investigatorss-ic have studied waterflooding using horizontal wells. droman et al, s reported a field application using horizontal wells in the Prudhoe Bay Unit where the main reservoir drive mechanism is gas cap expansion...

Jimenez, Zulay J.

1992-01-01T23:59:59.000Z

67

Horizontal Well Placement Optimization in Gas Reservoirs Using Genetic Algorithms  

E-Print Network [OSTI]

University Co-Chairs of Advisory Committee, Dr. Ding Zhu Dr. Hadi Nasrabadi Horizontal well placement determination within a reservoir is a significant and difficult step... optimization is an important criterion during the reservoir development phase of a horizontal-well project in gas reservoirs, but it is less significant to vertical wells in a homogeneous reservoir. It is also shown that genetic algorithms are an extremely...

Gibbs, Trevor Howard

2011-08-08T23:59:59.000Z

68

Kick circulation analysis for extended reach and horizontal wells  

E-Print Network [OSTI]

KICK CIRCULATION ANALYSIS FOR EXTENDED-REACH AND HORIZONTAL WELLS A Thesis by MAXIMILIAN M. LONG Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE December 2004 Major Subject: Petroleum Engineering KICK CIRCULATION ANALYSIS FOR EXTENDED-REACH AND HORIZONTAL WELLS A Thesis by MAXIMILIAN M. LONG Submitted...

Long, Maximilian Mark

2005-02-17T23:59:59.000Z

69

SATURATED-SUBCOOLED STRATIFIED FLOW IN HORIZONTAL PIPES  

SciTech Connect (OSTI)

Advanced light water reactor systems are designed to use passive emergency core cooling systems with horizontal pipes that provide highly subcooled water from water storage tanks or passive heat exchangers to the reactor vessel core under accident conditions. Because passive systems are driven by density gradients, the horizontal pipes often do not flow full and thus have a free surface that is exposed to saturated steam and stratified flow is present.

Richard Schultz

2010-08-01T23:59:59.000Z

70

Global Warming  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun with Big Sky LearningGet Assistance GetGiantOn The VergeGlobal Threat1 Global

71

Comminuting irradiated ferritic steel  

DOE Patents [OSTI]

Disclosed is a method of comminuting irradiated ferritic steel by placing the steel in a solution of a compound selected from the group consisting of sulfamic acid, bisulfate, and mixtures thereof. The ferritic steel is used as cladding on nuclear fuel rods or other irradiated components.

Bauer, Roger E. (Kennewick, WA); Straalsund, Jerry L. (Kennewick, WA); Chin, Bryan A. (Auburn, AL)

1985-01-01T23:59:59.000Z

72

Irradiation Creep in Graphite  

SciTech Connect (OSTI)

An understanding of the underlying mechanisms of irradiation creep in graphite material is required to correctly interpret experimental data, explain micromechanical modeling results, and predict whole-core behavior. This project will focus on experimental microscopic data to demonstrate the mechanism of irradiation creep. High-resolution transmission electron microscopy should be able to image both the dislocations in graphite and the irradiation-induced interstitial clusters that pin those dislocations. The team will first prepare and characterize nanoscale samples of virgin nuclear graphite in a transmission electron microscope. Additional samples will be irradiated to varying degrees at the Advanced Test Reactor (ATR) facility and similarly characterized. Researchers will record microstructures and crystal defects and suggest a mechanism for irradiation creep based on the results. In addition, the purchase of a tensile holder for a transmission electron microscope will allow, for the first time, in situ observation of creep behavior on the microstructure and crystallographic defects.

Ubic, Rick; Butt, Darryl; Windes, William

2014-03-13T23:59:59.000Z

73

Relative Accuracy of 1-Minute and Daily Total Solar Radiation Data for 12 Global and 4 Direct Beam Solar Radiometers: Preprint  

SciTech Connect (OSTI)

This report evaluates the relative performance of 12 global and four direct beam solar radiometers deployed at a single site over a 12-month period. Test radiometer irradiances were compared with a reference irradiance consisting of either an absolute cavity radiometer (during calibrations) or a low uncertainty thermopile pyrheliometer (during the evaluation period) for pyrheliometers; and for pyranometers a reference global irradiance computed from the reference pyrheliometer and diffuse irradiance from a shaded pyranometer.

Myers, D. R.; Wilcox, S. M.

2009-03-01T23:59:59.000Z

74

Global Health Research | 2 Global Health Research  

E-Print Network [OSTI]

Global Health Research | 2 Global Health Research Supporting researchers in low- and middle-income countries to carry out health- related research within their own countries. Gl bal Health #12;3 | Global Health Research #12;Global Health Research | 4 We are a global charitable foundation dedicated

Rambaut, Andrew

75

Air drilling has some pluses for horizontal wells  

SciTech Connect (OSTI)

Drilling horizontal wells with air as the circulating medium is not a common practice; however, air has come distinct advantages over drilling mud. They are: Significant increase in rate of penetration which leads to shorter drilling time. Elimination of lost circulation problems, especially in areas of very low bottom hole pressures. Continual drill stem test of potential producing formations. Minimal damage to the formation. Unfortunately, there are some disadvantages to drilling with air. Downhole motor life is shorter and less predictable. No measurement-while-drilling (MWD) system is currently available that will work consistently in air drilling environments. Hole cleaning is a problem at inclinations above 50{degree}. The horizontal section length is reduced because of the increased friction (drag) between the drillstring and borehole. The types of lithologies and targets are limited. Several horizontal wells have been successfully drilled with air or foam since 1986. At a minimum, operators drill the horizontal section with air or foam to eliminate lost circulation problems in low pressure or partially depleted reservoirs and to reduce formation damage due to drilling fluid invasion. However, problems have been encountered in drilling horizontal wells with air. Not all of the problems are unique to air drilling, but some may be exaggerated by the conditions in an air-drilled hole.

Carden, R.S. (Grace, Shursen, Moore and Associates, Inc., Amarillo, TX (US))

1991-04-08T23:59:59.000Z

76

Application of horizontal drilling to tight gas reservoirs  

SciTech Connect (OSTI)

Vertical fractures and lithologic heterogeneity are extremely important factors controlling gas flow rates and total gas recovery from tight (very low permeability) reservoirs. These reservoirs generally have in situ matrix permeabilities to gas of less than 0.1 md. Enhanced gas recovery methods have usually involved hydraulic fracturing; however, the induced vertical hydraulic fractures almost always parallel the natural fracture and may not be an efficient method to establish a good conduit to the wellbore. Horizontal drilling appears to be an optimum method to cut across many open vertical fractures. Horizontal holes will provide an efficient method to drain heterogeneous tight reservoirs even in unfractured rocks. Although many horizontal wells have now been completed in coalbed methane and oil reservoirs, very few have been drilled to exclusively evaluate tight gas reservoirs. The U.S. Department of Energy (DOE) has funded some horizontal and slanthole drilling in order to demonstrate the applicability of these techniques for gas development. Four DOE holes have been drilled in Devonian gas shales in the Appalachian basin, and one hole has been drilled in Upper Cretaceous tight sandstones in the Piceance basin of Colorado. The Colorado field experiment has provided valuable information on the abundance and openness of deeply buried vertical fractures in tight sandstones. These studies, plus higher gas prices, should help encourage industry to begin to further utilize horizontal drilling as a new exploitation method for tight gas reservoirs.

Spencer, C.W. (U.S. Geological Survey, Lakewood, CO (United States)); Lorenz, J.C. (Sandia National Labs., Albuquerque, NM (United States)); Brown, C.A. (Synder Oil Co., Denver, CO (United States))

1991-03-01T23:59:59.000Z

77

Understanding Global Capitalism  

E-Print Network [OSTI]

sociology; globalization; political economy; development;economy fueled through 700 billion dollars injected into globalizationGlobalization Studies, also called CGS. I would economy and

Robinson, William I.

2008-01-01T23:59:59.000Z

78

Review: Global Climate Change  

E-Print Network [OSTI]

introduction to global climate change, the greenhouseReview: Global Climate Change: A Primer By Orrin H PilkeyPilkey, Keith C. Global Climate Change: a primer. Durham,

Smith, Jennifer

2013-01-01T23:59:59.000Z

79

SOLAR IRRADIANCE FORECASTING FOR THE MANAGEMENT OF SOLAR ENERGY SYSTEMS  

E-Print Network [OSTI]

SOLAR IRRADIANCE FORECASTING FOR THE MANAGEMENT OF SOLAR ENERGY SYSTEMS Detlev Heinemann Oldenburg.girodo@uni-oldenburg.de ABSTRACT Solar energy is expected to contribute major shares of the future global energy supply. Due to its and solar energy conversion processes has to account for this behaviour in respective operating strategies

Heinemann, Detlev

80

Spatial Pattern Formation in Fused Silica Under UV Irradiation  

E-Print Network [OSTI]

Spatial Pattern Formation in Fused Silica Under UV Irradiation Problem Presenter Leslie Button lenses gradually degrades and ultimately damages these optical components. Corning is a global supplier of optical and ceramic materials across various industries and is particularly interested in this damage

Edwards, David A.

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Academy for Global Engagement  

E-Print Network [OSTI]

Academy for Global Engagement 2013-2014 Global Fellows #12;Meredith Gore and Wildlife #12;Global Research Interests · risk percepHon and public support and Agricultural Engineering #12;Global Research Interests · catalyHc conversion of biomass

82

global warming's six indias  

E-Print Network [OSTI]

global warming's six indias: An Audience Segmentation Analysis #12;Global Warming's Six Indias 1............................................................................................................................................20 2. Global Warming Beliefs and Attitudes................................................................................ 21 Knowledge about global warming varies widely by group

Haller, Gary L.

83

Horizontal Air Flow Drying Foods at Home Safely  

E-Print Network [OSTI]

Horizontal Air Flow Drying Foods at Home Safely Choosing a Food Dehydrator Drying is one. The thermostat should go up to 160 degrees F. The unit should have a fan or blower for air circulation. Mesh purposes. Types of Dehydrators There are two main types of dehydrators: those with vertical air flow

84

A Simplified Morphing Blade for Horizontal Axis Wind Turbines  

E-Print Network [OSTI]

A Simplified Morphing Blade for Horizontal Axis Wind Turbines Weijun WANG , St´ephane CARO, Fouad salinas@hotmail.com The aim of designing wind turbine blades is to improve the power capture ability by adjusting the twist of the blade's root and tip. To evaluate the performance of wind turbine blades

Recanati, Catherine

85

The Model Morphing Approach -Horizontal Transformations between Business Process  

E-Print Network [OSTI]

The Model Morphing Approach - Horizontal Transformations between Business Process Models Marion and business to busi- ness interoperability, there is a need for model transformations in the area of business this paper concentrates on transformations of models between different business process modeling languages

86

Experimental investigation of a horizontal flexible-membrane wave barrier  

E-Print Network [OSTI]

A series of experiments is conducted in a two-dimensional glass-walled wave tank to confirm numerical solutions based on two-dimensional linear hydro-elastic theory for a horizontal flexible-membrane wave barrier. The model test is performed by a...

Choi, Hae-Jin

1997-01-01T23:59:59.000Z

87

Predicting horizontal well performance in solution-gas drive reservoirs  

E-Print Network [OSTI]

of these wells were located in France and the fourth was located in waters off the coast cf Italy. Horizontal sections over 1000 ft were drilled and well productivities of up to twenty times those of r eighboring ve !ical wel!s were reported In 1979, ARCO...

Plahn, Sheldon Von

1986-01-01T23:59:59.000Z

88

Horizontal drilling the Bakken Formation, Williston basin: A new approach  

SciTech Connect (OSTI)

Horizontal drilling is an attractive new approach to exploration and development of the Mississippian/Devonian Bakken Formation in the southwestern part of North Dakota. This drilling technique increases the probability of success, the profit potential, the effective drainage area maximizing recoverable reserves, and the productivity by encountering more natural occurring fractures. The target formation, the Mississippian/Devonian Bakken, consists of three members in an overlapping relationship, a lower organic-rich black shale, a middle siltstone/limestone, and an upper organic-rich black shale. It attains a maximum thickness of 145 ft and thins to a feather edge along its depositional limit. Considered to be a major source rock for the Williston basin, the Bakken is usually overpressured where productive. Overpressuring is attributed to intense hydrocarbon generation. Reservoir properties are poor with core fluid porosities being generally 5% or less and permeabilities ranging from 0.1 to 0.2 md. The presence of natural fractures in the shale are necessary for production. Two types of fractures are associated with Bakken reservoirs: large vertical fractures (of tectonic origin) and microfractures (probably related to hydrocarbon generation). An economic comparison between horizontal and vertical wells show that well completion costs are approximately two times higher (average costs; $1,500,000 for a horizontal to $850,000 for a vertical) with average payout for horizontal wells projected to occur in half the time (1.5 yr instead of 3.4 yr). Projected production and reserves are considered to be 2 to 4 times greater from a horizontal well.

Lefever, J.A. (North Dakota Geological Survey, Grand Forks (USA))

1990-05-01T23:59:59.000Z

89

Irradiation Stability of Carbon Nanotubes  

E-Print Network [OSTI]

Ion irradiation of carbon nanotubes is a tool that can be used to achieve modification of the structure. Irradiation stability of carbon nanotubes was studied by ion and electron bombardment of the samples. Different ion species at various energies...

Aitkaliyeva, Assel

2010-01-14T23:59:59.000Z

90

Geological aspects of the first horizontal well drilled in Romania  

SciTech Connect (OSTI)

In 1979 on the Lebada Est field of the Romanian Offshore of the Black Sea between the Albian and the Eocene hydrocarbon accumulations, the Upper Cretaceous hydrocarbon accumulation was discovered. Situated in the Coniacian-Santonian and Turonian limey rocks, this accumulation cannot be produced efficiently by conventional wells. Some geological aspects which characterize the field such as: the physical properties of the reservoir rocks, the low effective thickness, heterogeneity, the vertical fissure and microfissure system and other production and economic aspects led to the conclusion that oil can be produced efficiently by horizontal wells or high angle wells. The benefits of horizontal well trajectory to produce the oil from the reservoir with this geometry are many and they were proved by the high rate of production as compared with the production tests of the vertical wells. After a long period of time when the reservoir was considered to be economically inefficient it can be finally produced.

Baleanu, C.; Petrom, R.A. [Institute for Research and Technology, Prahova (Romania)

1995-08-01T23:59:59.000Z

91

The Critical Rayleigh Number in Horizontal Convection for $\\Pran=1$  

E-Print Network [OSTI]

We report the numerical simulations of the horizontal convection within a rectangle cavity tank at high Rayleigh numbers. The physical solution of horizontal convection depends the space resolution of the meshes. The mesh number $N$ is proportion to $Ra^{1/3}$. The unstable numerical solutions are obtained as $Npower law also implies that the space resolution is dominated by the viscosity and heat diffusion. It implies that the special resolution is dominated by viscosity and thermal diffusivity but the length of the tank. Moreover, there is a Hopf bifurcation from steady solutions to unsteady solutions and the critical Rayleigh number $Ra_c$ is obtained as $5.53\\times 10^8

Sun, L; Sun, De-Jun; Sun, Liang

2007-01-01T23:59:59.000Z

92

Horizontal-well pilot waterflood tests shallow, abandoned field  

SciTech Connect (OSTI)

This paper reports on the suitability of using horizontal wells in a waterflood of shallow, partially depleted sands which will be tested in the Jennings field in Oklahoma. The vertical wells drilled in the Jennings field intersect several well-known formations such as Red Fork, Misner, and Bartlesville sand. Most of these formations have been produced over a number of years, and presently no wells are producing in the field. In the 1940s, 1950s, and 1960s, wells were drilled on 10-acre spacing, and the last well was plugged in 1961. The field was produced only on primary production and produced approximately 1 million bbl of oil. Because the field was not waterflooded, a large potential exists to produce from the field using secondary methods. To improve the economics for the secondary process, a combination of horizontal and vertical wells was considered.

McAlpine, J.L. (White Buffalo Petroleum Co., Tulsa, OK (US)); Joshi, S.D. (Joshi Technologies International Inc., Tulsa, OK (US))

1991-08-05T23:59:59.000Z

93

Evaluation of Horizontal Seismic Hazard of Shahrekord, Iran  

SciTech Connect (OSTI)

This paper presents probabilistic horizontal seismic hazard assessment of Shahrekord, Iran. It displays the probabilistic estimate of Peak Ground Horizontal Acceleration (PGHA) for the return period of 75, 225, 475 and 2475 years. The output of the probabilistic seismic hazard analysis is based on peak ground acceleration (PGA), which is the most common criterion in designing of buildings. A catalogue of seismic events that includes both historical and instrumental events was developed and covers the period from 840 to 2007. The seismic sources that affect the hazard in Shahrekord were identified within the radius of 150 km and the recurrence relationships of these sources were generated. Finally four maps have been prepared to indicate the earthquake hazard of Shahrekord in the form of iso-acceleration contour lines for different hazard levels by using SEISRISK III software.

Amiri, G. Ghodrati [Iran University of Science and Technology--Islamic Azad University of Shahrekord, Narmak, Tehran 16846 (Iran, Islamic Republic of); Dehkordi, M. Raeisi [Department of Civil Engineering, Islamic Azad University of Shahrekord (Iran, Islamic Republic of); Amrei, S. A. Razavian [College of Civil Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Kamali, M. Koohi [Department of Civil Engineering, Islamic Azad University of Shahrekord (Iran, Islamic Republic of)

2008-07-08T23:59:59.000Z

94

QUESTIONS ABOUT GLOBAL WARMING  

E-Print Network [OSTI]

QUESTIONS ABOUT GLOBAL WARMING ¥IS IT REAL? ¥IS IT IMPORTANT? ¥WHAT IS IT DUE TO? ¥HOW MUCH MORE in the atmosphere, giving Earth its temperate climate. Global Atmosphere, Global Warming GLOBAL TEMPERATURE TREND�t a cure for global warming! Aerosols only last a short while in the atmosphere, they would have

95

Horizontal film balance having wide range and high sensitivity  

DOE Patents [OSTI]

A thin-film, horizontal balance instrument is provided for measuring surface tension (surface energy) of thin films suspended on a liquid substrate. The balance includes a support bearing and an optical feedback arrangement for wide-range, high sensitivity measurements. The force on the instrument is balanced by an electromagnet, the current through the magnet providing a measure of the force applied to the instrument. A novel float construction is also disclosed.

Abraham, B.M.; Miyano, K.; Ketterson, J.B.

1981-03-05T23:59:59.000Z

96

Horizontal film balance having wide range and high sensitivity  

DOE Patents [OSTI]

A thin-film, horizontal balance instrument is provided for measuring surface tension (surface energy) of thin films suspended on a liquid substrate. The balance includes a support bearing and an optical feedback arrangement for wide-range, high sensitivity measurements. The force on the instrument is balanced by an electromagnet, the current through the magnet providing a measure of the force applied to the instrument. A novel float construction is also disclosed. 5 figs.

Abraham, B.M.; Miyano, K.; Ketterson, J.B.

1983-11-08T23:59:59.000Z

97

Horizontal film balance having wide range and high sensitivity  

DOE Patents [OSTI]

A thin-film, horizontal balance instrument is provided for measuring surface tension (surface energy) of thin films suspended on a liquid substrate. The balance includes a support bearing and an optical feedback arrangement for wide-range, high sensitivity measurements. The force on the instrument is balanced by an electromagnet, the current through the magnet providing a measure of the force applied to the instrument. A novel float construction is also disclosed.

Abraham, Bernard M. (Oak Park, IL); Miyano, Kenjiro (Downers Grove, IL); Ketterson, John B. (Evanston, IL)

1983-01-01T23:59:59.000Z

98

A mathematical simulation of horizontal drain-hole performance  

E-Print Network [OSTI]

Science and Technology, Kee-Lung, Taiwan, Republic of China Chairman of Advisory Comnittee: Dr. Ching H. Wu The application of horizontal drain-hole in petroleum industry represents one of the new developments in oil recovery techniques. Many... production condition was simulated. The validity of the computational algorithm employed in the simulator was ascertained using the results obtained from a general purpose black oil simulator, BOSS-AIM. The verification runs were made under a semi...

Cheng, Thomas Ru-Kang

1984-01-01T23:59:59.000Z

99

Horizontal natural gas storage caverns and methods for producing same  

DOE Patents [OSTI]

The invention provides caverns and methods for producing caverns in bedded salt deposits for the storage of materials that are not solvents for salt. The contemplated salt deposits are of the bedded, non-domed variety, more particularly salt found in layered formations that are sufficiently thick to enable the production of commercially usefully sized caverns completely encompassed by walls of salt of the formation. In a preferred method, a first bore hole is drilled into the salt formation and a cavity for receiving insolubles is leached from the salt formation. Thereafter, at a predetermined distance away from the first bore hole, a second bore hole is drilled towards the salt formation. As this drill approaches the salt, the drill assumes a slant approach and enters the salt and drills through it in a horizontal direction until it intersects the cavity for receiving insolubles. This produces a substantially horizontal conduit from which solvent is controlledly supplied to the surrounding salt formation, leaching the salt and producing a concentrated brine which is removed through the first bore hole. Insolubles are collected in the cavity for receiving insolubles. By controlledly supplying solvent, a horizontal cavern is produced with two bore holes extending therefrom.

Russo, Anthony (Albuquerque, NM)

1995-01-01T23:59:59.000Z

100

Horizontal well improves oil recovery from polymer flood--  

SciTech Connect (OSTI)

Horizontal drilling associated with an injection scheme appears to be highly promising for obtaining additional oil recovery. Horizontal well CR 163H, in the Chateaurenard field is discussed. It demonstrated that a thin unconsolidated sand can be successfully drilled and cased. The productivity index (PI) of the well was much greater than vertical wells, and an unproduced oil bank was successfully intersected. On the negative side, it was necessary to pump low in a very deviated part of the well, and the drilling cost was high compared to an onshore vertical well. CR 163H was the fifth and probably most difficult horizontal well drilled by Elf Aquitaine. Located within a polymer-flood project, the target was a 7-m thick sand reservoir at a vertical depth of 590:0080 m. In this inverted seven-spot configuration with one injector in the center and six producers at a distance of 400 m, a polymer solution was injected from 1977 to 1983, followed by water injection.

Bruckert, L. (Elf Aquitaine, Boussens, (FR))

1989-12-18T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Natural convection heat transfer within horizontal spent nuclear fuel assemblies  

SciTech Connect (OSTI)

Natural convection heat transfer is experimentally investigated in an enclosed horizontal rod bundle, which characterizes a spent nuclear fuel assembly during dry storage and/or transport conditions. The basic test section consists of a square array of sixty-four stainless steel tubular heaters enclosed within a water-cooled rectangular copper heat exchanger. The heaters are supplied with a uniform power generation per unit length while the surrounding enclosure is maintained at a uniform temperature. The test section resides within a vacuum/pressure chamber in order to subject the assembly to a range of pressure statepoints and various backfill gases. The objective of this experimental study is to obtain convection correlations which can be used in order to easily incorporate convective effects into analytical models of horizontal spent fuel systems, and also to investigate the physical nature of natural convection in enclosed horizontal rod bundles in general. The resulting data consist of: (1) measured temperatures within the assembly as a function of power, pressure, and backfill gas; (2) the relative radiative contribution for the range of observed temperatures; (3) correlations of convective Nusselt number and Rayleigh number for the rod bundle as a whole; and (4) correlations of convective Nusselt number as a function of Rayleigh number for individual rods within the array.

Canaan, R.E.

1995-12-01T23:59:59.000Z

102

Hydrodynamic and Structural Performance of the Transverse Horizontal Axis Water Turbine  

E-Print Network [OSTI]

power (2) · Vertical axis turbines ­ Blue Energy ­ Polo ­ ... 4 other vertical axis devices · Horizontal of Darrieus vertical axis wind turbine (VAWT) through 90 to lie horizontally across a tidal flow · StretchHydrodynamic and Structural Performance of the Transverse Horizontal Axis Water Turbine Prof. Guy

Gorban, Alexander N.

103

SDI: Solar Dome Instrument for Solar Irradiance Monitoring Tao Liu1, Ankur U. Kamthe1, Varick L. Erickson1, Carlos F. M. Coimbra2 and Alberto E. Cerpa1  

E-Print Network [OSTI]

SDI: Solar Dome Instrument for Solar Irradiance Monitoring Tao Liu1, Ankur U. Kamthe1, Varick L data for ground solar irradiance (direct normal and global irradiance) is a major obstacle for the de- velopment of adequate policies to promote and take advan- tage of existing solar technologies. Although

Cerpa, Alberto E.

104

Cosmic Rays and Global Warming  

SciTech Connect (OSTI)

Some workers have claimed that the observed temporal correlations of (low level) terrestrial cloud cover with the cosmic ray intensity changes, due to solar modulation, are causal. The possibility arises, therefore, of a connection between cosmic rays and Global Warming. If true, the implications would be very great. We have examined this claim in some detail. So far, we have not found any evidence in support and so our conclusions are to doubt it. From the absence of corroborative evidence we estimate that less than 15% at the 95% confidence level, of the 11-year cycle warming variations are due to cosmic rays and less than 2% of the warming over the last 43 years is due to this cause. The origin of the correlation itself is probably the cycle of solar irradiance although there is, as yet, no certainty.

Sloan, T. [Physics Department, University of Lancaster, Lancaster, UK (United Kingdom); Wolfendale, A. W. [Physics Department, Durham University, Durham (United Kingdom)

2008-01-24T23:59:59.000Z

105

Cosmic Rays and Global Warming  

E-Print Network [OSTI]

It has been claimed by others that observed temporal correlations of terrestrial cloud cover with `the cosmic ray intensity' are causal. The possibility arises, therefore, of a connection between cosmic rays and Global Warming. If true, the implications would be very great. We have examined this claim to look for evidence to corroborate it. So far we have not found any and so our tentative conclusions are to doubt it. Such correlations as appear are more likely to be due to the small variations in solar irradiance, which, of course, correlate with cosmic rays. We estimate that less than 15% of the 11-year cycle warming variations are due to cosmic rays and less than 2% of the warming over the last 35 years is due to this cause.

T. Sloan; A W Wolfendale

2007-06-28T23:59:59.000Z

106

Application of horizontal wells in steeply dipping reservoirs  

E-Print Network [OSTI]

) + Rplj)/2 Np = Np(j-1) + DELTA Np R3 - Rs +[(kg/ko)(Uo/Ug)(Bo/Bg)] Gp = Gp 4-1) + DELTA NpsRp avg Rec. Fac. = Np/OOIP Rp=Gp/Np 43 IE+06 lE+05 a 1E+04 1E+03 ~m=000 ? a ? m=0, 08 ~m=0. 24 1965 1970 1975 1980 1985 1990 1995 Time (years) Fig... Major Subject: Petroleum Engineering ABSTRACT Application of Horizontal Wells in Steeply Dipping Reservoirs. (December 1995) Jose David Lopez Navarro, B. S. , Universidad de America Santafe de Bogota, Colombia Co-chairs of Advisory Committee: Dr...

Lopez Navarro, Jose David

1995-01-01T23:59:59.000Z

107

Global Health Seminar Series  

E-Print Network [OSTI]

Bay Area Global Health Seminar Series Moving beyond millennium targets in global health: The challenges of investing in health and universal health coverage Although targets can help to focus global health efforts, they can also detract attention from deeper underlying challenges in global health

Klein, Ophir

108

Global Warming Observations  

E-Print Network [OSTI]

Global Warming Observations: 1. Global temperature has been gradually rising in recent years #15 in range 8000 12000 nm { CFC's, methane and N 2 O important for global warming even though concentra- tions in concentration of \\greenhouse gases" like CO 2 What determines global temperature? Energy budget of earth: 1

Schofield, Jeremy

109

Crosswell Imaging Technology & Advanced DSR Navigation for Horizontal Directional Drilling  

SciTech Connect (OSTI)

The objective of Phase II is to develop and demonstrate real-time measurement-while-drilling (MWD) for guidance and navigation of drill strings during horizontal drilling operations applicable to both short and long holes. The end product of Phase II is a functional drill-string assembly outfitted with a commercial version of Drill String Radar (DSR). Project Objectives Develop and demonstrate a dual-phase methodology of in-seam drilling, imaging, and structure confirmation. This methodology, illustrated in Figure 1, includes: (1) Using RIM to image between drill holes for seam thickness estimates and in-seam structures detection. Completed, February 2005; and (2) Using DSR for real-time MWD guidance and navigation of drillstrings during horizontal drilling operations. Completed, November 2008. As of November 2008, the Phase II portion of Contract DE-FC26-04NT42085 is about 99% complete, including milestones and tasks original outlined as Phase II work. The one percent deficiency results from MSHA-related approvals which have yet to be granted (at the time of reporting). These approvals are pending and are do not negatively impact the scope of work or project objectives.

Larry Stolarczyk

2008-08-08T23:59:59.000Z

110

Horizontal well drill-in fluid utilizing alcohol ethoxylate  

SciTech Connect (OSTI)

The drilling of horizontal wells in the last 6 years has significantly improved the economics of oil and gas production from depleted reservoirs or tight sands. This paper illustrates the application of an alcohol ethoxylate into a drill-in fluid designed to minimize formation damage in low permeability sandstones while drilling horizontal sections as long as 1,617 meters (5,306 ft) at depths approaching 6,580 meters (21,600 ft) and to facilitate formation cleanup. The chemistry of alcohol ethoxylates/alkoxylates are described and the more popular names used within the industry will be discussed. Laboratory results are presented which illustrate colloidal phenomena not previously reported with these systems, the routes taken for successful application into a drill-in fluid and how complex these particular colloidal systems are from a physical chemical viewpoint, along with the inevitable learning curve required to fully optimize these systems. Generalized case histories from the UK Southern North Sea will be described, along with field observations which back up the colloidal phenomena seen in the laboratory.

Jachnik, R.P.; Green, P.

1995-11-01T23:59:59.000Z

111

Evaluation of Radiometers Deployed at the National Renewable Energy Laboratory's Solar Radiation Research Laboratory  

SciTech Connect (OSTI)

This study analyzes the performance of various commercially available radiometers used for measuring global horizontal irradiances and direct normal irradiances. These include pyranometers, pyrheliometers, rotating shadowband radiometers, and a pyranometer with fixed internal shading and are all deployed at the National Renewable Energy Laboratory's Solar Radiation Research Laboratory. Data from 32 global horizontal irradiance and 19 direct normal irradiance radiometers are presented. The radiometers in this study were deployed for one year (from April 1, 2011, through March 31, 2012) and compared to measurements from radiometers with the lowest values of estimated measurement uncertainties for producing reference global horizontal irradiances and direct normal irradiances.

Habte, A.; Wilcox, S.; Stoffel, T.

2014-02-01T23:59:59.000Z

112

Simulation of the Summer Monsoon Rainfall over East Asia using the NCEP GFS Cumulus Parameterization at Different Horizontal Resolutions  

SciTech Connect (OSTI)

The most recent version of Simplified Arakawa-Schubert (SAS) cumulus scheme in National Center for Environmental Prediction (NCEP) Global Forecast System (GFS) (GFS SAS) has been implemented into the Weather and Research Forecasting (WRF) model with a modification of triggering condition and convective mass flux to become depending on model’s horizontal grid spacing. East Asian Summer Monsoon of 2006 from June to August is selected to evaluate the performance of the modified GFS SAS scheme. Simulated monsoon rainfall with the modified GFS SAS scheme shows better agreement with observation compared to the original GFS SAS scheme. The original GFS SAS scheme simulates the similar ratio of subgrid-scale precipitation, which is calculated from a cumulus scheme, against total precipitation regardless of model’s horizontal grid spacing. This is counter-intuitive because the portion of resolved clouds in a grid box should be increased as the model grid spacing decreases. This counter-intuitive behavior of the original GFS SAS scheme is alleviated by the modified GFS SAS scheme. Further, three different cumulus schemes (Grell and Freitas, Kain and Fritsch, and Betts-Miller-Janjic) are chosen to investigate the role of a horizontal resolution on simulated monsoon rainfall. The performance of high-resolution modeling is not always enhanced as the spatial resolution becomes higher. Even though improvement of probability density function of rain rate and long wave fluxes by the higher-resolution simulation is robust regardless of a choice of cumulus parameterization scheme, the overall skill score of surface rainfall is not monotonically increasing with spatial resolution.

Lim, Kyo-Sun; Hong, Song You; Yoon, Jin-Ho; Han, Jongil

2014-10-01T23:59:59.000Z

113

High-frequency shear-horizontal surface acoustic wave sensor  

DOE Patents [OSTI]

A Love wave sensor uses a single-phase unidirectional interdigital transducer (IDT) on a piezoelectric substrate for leaky surface acoustic wave generation. The IDT design minimizes propagation losses, bulk wave interferences, provides a highly linear phase response, and eliminates the need for impedance matching. As an example, a high frequency (.about.300-400 MHz) surface acoustic wave (SAW) transducer enables efficient excitation of shear-horizontal waves on 36.degree. Y-cut lithium tantalate (LTO) giving a highly linear phase response (2.8.degree. P-P). The sensor has the ability to detect at the pg/mm.sup.2 level and can perform multi-analyte detection in real-time. The sensor can be used for rapid autonomous detection of pathogenic microorganisms and bioagents by field deployable platforms.

Branch, Darren W

2013-05-07T23:59:59.000Z

114

High-frequency shear-horizontal surface acoustic wave sensor  

SciTech Connect (OSTI)

A Love wave sensor uses a single-phase unidirectional interdigital transducer (IDT) on a piezoelectric substrate for leaky surface acoustic wave generation. The IDT design minimizes propagation losses, bulk wave interferences, provides a highly linear phase response, and eliminates the need for impedance matching. As an example, a high frequency (.about.300-400 MHz) surface acoustic wave (SAW) transducer enables efficient excitation of shear-horizontal waves on 36.degree. Y-cut lithium tantalate (LTO) giving a highly linear phase response (2.8.degree. P-P). The sensor has the ability to detect at the pg/mm.sup.2 level and can perform multi-analyte detection in real-time. The sensor can be used for rapid autonomous detection of pathogenic microorganisms and bioagents by field deployable platforms.

Branch, Darren W

2014-03-11T23:59:59.000Z

115

Gravity wave turbulence revealed by horizontal vibrations of the container  

E-Print Network [OSTI]

We experimentally study the role of the forcing on gravity-capillary wave turbulence. Previous laboratory experiments using spatially localized forcing (vibrating blades) have shown that the frequency power-law exponent of the gravity wave spectrum depends on the forcing parameters. By horizontally vibrating the whole container, we observe a spectrum exponent that does not depend on the forcing parameters for both gravity and capillary regimes. This spatially extended forcing leads to a gravity spectrum exponent in better agreement with the theory than by using a spatially localized forcing. The role of the vessel shape has been also studied. Finally, the wave spectrum is found to scale linearly with the injected power for both regimes whatever the forcing type used.

Bruno Issenmann; Eric Falcon

2012-12-20T23:59:59.000Z

116

Magnetic Flux Dynamics in Horizontally Cooled Superconducting Cavities  

E-Print Network [OSTI]

Previous studies on magnetic flux expulsion as a function of cooling details have been performed for superconducting niobium cavities with the cavity beam axis placed parallel respect to the helium cooling flow, and findings showed that for sufficient cooling thermogradients all magnetic flux could be expelled and very low residual resistance could be achieved. In this paper we investigate the flux trapping and its impact on radio frequency surface resistance when the resonators are positioned perpendicularly to the helium cooling flow, which is representative of how superconducting radio-frequency (SRF) cavities are cooled in an accelerator. We also extend the studies to different directions of applied magnetic field surrounding the resonator. Results show that in the cavity horizontal configuration there is a different impact of the various field components on the final surface resistance, and that several parameters have to be considered to understand flux dynamics. A newly discovered phenomenon of concent...

Martinello, M; Grassellino, A; Crawford, A C; Melnychuk, O; Romanenko, A; Sergatkov, D A

2015-01-01T23:59:59.000Z

117

Interphase transport in horizontal stratified cocurrent flow. [PWR; BWR  

SciTech Connect (OSTI)

The problem of interfacial transport in cocurrent, horizontal stratified gas-liquid systems is considered. Local condensation heat transfer coefficients and interface shear stress were obtained from mass and force balances. These balances were based on gas phase pitot traverses at various streamwise locations. Laser anemometer measurements of liquid mean and rms fluctuation velocities were made at similar locations. The laser anemometer data supported the value for the interface shear velocity obtained by the gas phase force balance. Based on cocurrent stratified air-water flow data the noncondensing interface shear stress was found to be a function of the relative velocity between the phases and the liquid fraction. Incorporated into Linehan's relation for condensing flow shear stress, the correlation was found to estimate the shear velocity for the condensation data considered. Local condensation heat transfer coefficients and gas absorption mass transfer coefficients were found to be directly proportional to the shear velocity.

Jensen, R.J.; Yuen, M.C.

1982-05-01T23:59:59.000Z

118

Globalization of biopharmaceutical manufacturing  

E-Print Network [OSTI]

The biomanufacturing industry is changing due to increasing globalization. However, it is changing differently from other high tech industries like software/ semiconductor/ automobiles. In this study we use global ...

Pande, Rachna

2011-01-01T23:59:59.000Z

119

Nonsingular static global string  

E-Print Network [OSTI]

A new solution for the spacetime outside the core of a U(1) static global string has been presented which is nonsingular. This is the first example of a nonsingular spacetime around a static global string.}}

A. A. Sen; N. Banerjee

2000-04-12T23:59:59.000Z

120

Review: Globalization of Water  

E-Print Network [OSTI]

Review: Globalization of Water: Sharing the Planet’sAshok K. Globalization of Water: Sharing the Planet’s140) liters of virtual water (p. 15). This is one of the

Tennant, Matthew Aaron

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Global Environmental Course Title  

E-Print Network [OSTI]

Department Global Environmental Studies Room Course Title Frontier of Sustainability Science Instructor Akihisa MORI, Global Environmental Studies Satoshi KONISHI, Institute of Advanced consisting from a variety of academic field, including philosophy, politics, economics, energy, architecture

Takada, Shoji

122

Cows Causing Global Warming  

E-Print Network [OSTI]

Broadcast Transcript: Remember when President Reagan blamed trees for air pollution? Well now the Japanese are blaming cows for global warming. Apparently, the methane emissions from burping cows account for 5% of all global greenhouse gases. Simple...

Hacker, Randi

2008-08-06T23:59:59.000Z

123

Horizontal oil well applications and oil recovery assessment. Technical progress report, April--June 1994  

SciTech Connect (OSTI)

Thousands of horizontal wells are being drilled each year in the U.S.A. and around the world. Horizontal wells have increased oil and gas production rates 3 to 8 times those of vertical wells in many areas and have converted non-economic oil reserves to economic reserves. However, the use of horizontal technology in various formation types and applications has not always yielded anticipated success. The primary objective of this project is to examine factors affecting technical and economic success of horizontal well applications. The project`s goals will be accomplished through six tasks designed to evaluate the technical and economic success of horizontal drilling, highlight current limitations, and outline technical needs to overcome these limitations. Data describing operators` experiences throughout the domestic oil and gas industry will be gathered and organized. Canadian horizontal technology will also be documented with an emphasis on lessons the US industry can learn from Canada`s experience. MEI databases containing detailed horizontal case histories will also be used. All these data will be categorized and analyzed to assess the status of horizontal well technology and estimate the impact of horizontal wells on present and future domestic oil recovery and reserves.

McDonald, W.J.

1993-06-03T23:59:59.000Z

124

Subsurface horizontal microfracture propagation within the middle member of the Bakken Formation, Williston Basin, North Dakota.  

E-Print Network [OSTI]

??The Devonian-Mississippian Bakken Formation of the Williston basin does not outcrop. All rock samples are obtained by coring. Open, uncemented, horizontal mode I (joints, with… (more)

Warner, Travis Blackburn.

2011-01-01T23:59:59.000Z

125

Zero Discharge Water Management for Horizontal Shale Gas Well Development  

SciTech Connect (OSTI)

Hydraulic fracturing technology (fracking), coupled with horizontal drilling, has facilitated exploitation of huge natural gas (gas) reserves in the Devonian-age Marcellus Shale Formation (Marcellus) of the Appalachian Basin. The most-efficient technique for stimulating Marcellus gas production involves hydraulic fracturing (injection of a water-based fluid and sand mixture) along a horizontal well bore to create a series of hydraulic fractures in the Marcellus. The hydraulic fractures free the shale-trapped gas, allowing it to flow to the well bore where it is conveyed to pipelines for transport and distribution. The hydraulic fracturing process has two significant effects on the local environment. First, water withdrawals from local sources compete with the water requirements of ecosystems, domestic and recreational users, and/or agricultural and industrial uses. Second, when the injection phase is over, 10 to 30% of the injected water returns to the surface. This water consists of flowback, which occurs between the completion of fracturing and gas production, and produced water, which occurs during gas production. Collectively referred to as returned frac water (RFW), it is highly saline with varying amounts of organic contamination. It can be disposed of, either by injection into an approved underground injection well, or treated to remove contaminants so that the water meets the requirements of either surface release or recycle use. Depending on the characteristics of the RFW and the availability of satisfactory disposal alternatives, disposal can impose serious costs to the operator. In any case, large quantities of water must be transported to and from well locations, contributing to wear and tear on local roadways that were not designed to handle the heavy loads and increased traffic. The search for a way to mitigate the situation and improve the overall efficiency of shale gas production suggested a treatment method that would allow RFW to be used as make-up water for successive fracs. RFW, however, contains dissolved salts, suspended sediment and oils that may interfere with fracking fluids and/or clog fractures. This would lead to impaired well productivity. The major technical constraints to recycling RFW involves: identification of its composition, determination of industry standards for make-up water, and development of techniques to treat RFW to acceptable levels. If large scale RFW recycling becomes feasible, the industry will realize lower transportation and disposal costs, environmental conflicts, and risks of interruption in well development schedules.

Paul Ziemkiewicz; Jennifer Hause; Raymond Lovett; David Locke Harry Johnson; Doug Patchen

2012-03-31T23:59:59.000Z

126

Design Editorial Globalization and Internationalism  

E-Print Network [OSTI]

; especially, the development of an increasingly integrated global economy marked especially by free tradeJournal of Mechanical Design Editorial Globalization and Internationalism There has always been and Strabo, but to Friedman's empirical observations of globalization. According to Wikipedia, "globalization

Papalambros, Panos

127

A Parametric Study on the Benefits of Drilling Multilateral and Horizontal Wells in  

E-Print Network [OSTI]

A Parametric Study on the Benefits of Drilling Multilateral and Horizontal Wells in Coalbed Methane reservoirs can be drained with horizontal well configurations. - In a very short time, coal system can, Texas SPE Paper # 96018 #12;- Coal is an unusual reservoir rock, with highly complex reservoir

Mohaghegh, Shahab

128

Near wake properties of horizontal axis marine current L. Myers and A.S. Bahaj  

E-Print Network [OSTI]

1 Near wake properties of horizontal axis marine current turbines L. Myers and A.S. Bahaj wake region of a tidal current turbine is strongly driven by the combined wake of the device support-scale horizontal axis turbine has been have been measured in a large water channel facility. A downstream map

Quartly, Graham

129

LQG control of horizontal wind turbines for blades and tower loads alleviation  

E-Print Network [OSTI]

LQG control of horizontal wind turbines for blades and tower loads alleviation A. Pintea*, N of power produced by two bladed horizontal variable speed wind turbines. The proposed controller ensures oscillations and with the tower bending tendency. Keywords: LQG control, Wind turbines, Multi-objective control

Paris-Sud XI, Université de

130

Experimental study of hydraulic transport of large particles in horizontal and S-shape pipes  

E-Print Network [OSTI]

Experimental study of hydraulic transport of large particles in horizontal and S-shape pipes F and solid mixture that flows in a horizontal pipe and in a vertical S-shaped pipe. Two densities are used for the solids. The solids are spheres that are large with respect to the diameter of the pipe (5, 10 and 15

Paris-Sud XI, Université de

131

Impact of horizontal groundwater flow and localized deforestation on the development of shallow  

E-Print Network [OSTI]

Impact of horizontal groundwater flow and localized deforestation on the development of shallow that develop in the shallow subsurface as a result of localized deforestation in combination with shallow horizontal groundwater flow. Model results show how a patch-wise pattern of deforestation at the surface

Bense, Victor

132

Hydraulics of horizontal wells in fractured shallow aquifer systems Eungyu Parka,*, Hongbin Zhanb  

E-Print Network [OSTI]

Hydraulics of horizontal wells in fractured shallow aquifer systems Eungyu Parka,*, Hongbin Zhanb Accepted 1 May 2003 Abstract An analysis of groundwater hydraulic head in the vicinity of a horizontal well in fractured or porous aquifers considering confined, leaky confined, and water-table aquifer boundary

Zhan, Hongbin

133

A practical modification of horizontal line sampling for snag and cavity tree inventory  

E-Print Network [OSTI]

A practical modification of horizontal line sampling for snag and cavity tree inventory M.J. Ducey features in forests, but they are often sparsely distributed, making efficient inventories problematic. We present a straightforward modification of horizontal line sampling de- signed to facilitate inventory

134

Horizontal subduction and truncation of the Cocos Plate beneath central Mexico  

E-Print Network [OSTI]

Horizontal subduction and truncation of the Cocos Plate beneath central Mexico Xyoli Pe from a trans-Mexico temporary broadband seismic network centered on Mexico City, we report that the subducting Cocos Plate beneath central Mexico is horizontal, and tectonically underplates the base

Clayton, Robert W.

135

The Thermal Regulation of Gravitational Instabilities in Protoplanetary Disks. IV. Simulations with Envelope Irradiation  

E-Print Network [OSTI]

It is generally thought that protoplanetary disks embedded in envelopes are more massive and thus more susceptible to gravitational instabilities (GIs) than exposed disks. We present three-dimensional radiative hydrodynamics simulations of protoplanetary disks with the presence of envelope irradiation. For a disk with a radius of 40 AU and a mass of 0.07 Msun around a young star of 0.5 Msun, envelope irradiation tends to weaken and even suppress GIs as the irradiating flux is increased. The global mass transport induced by GIs is dominated by lower-order modes, and irradiation preferentially suppresses higher-order modes. As a result, gravitational torques and mass inflow rates are actually increased by mild irradiation. None of the simulations produce dense clumps or rapid cooling by convection, arguing against direct formation of giant planets by disk instability, at least in irradiated disks. However, dense gas rings and radial mass concentrations are produced, and these might be conducive to accelerated planetary core formation. Preliminary results from a simulation of a massive embedded disk with physical characteristics similar to one of the disks in the embedded source L1551 IRS5 indicate a long radiative cooling time and no fragmentation. The GIs in this disk are dominated by global two and three-armed modes.

Kai Cai; Richard H. Durisen; Aaron C. Boley; Megan K. Pickett; Annie C. Mejia

2007-10-17T23:59:59.000Z

136

Horizontal oil well applications and oil recovery assessment. Technical progress report, January--March 1994  

SciTech Connect (OSTI)

The primary objective of this project is to examine factors affecting technical and economic success of horizontal well applications. The project`s goals will be accomplished through five tasks designed to evaluate the technical and economic success of horizontal drilling, highlight current limitations, and outline technical needs to overcome these limitations. Data describing operators` experiences throughout the domestic oil and gas industry will be gathered and organized. MEI databases containing detailed horizontal case histories will also be used. All these data will be categorized and analyzed to assess the status of horizontal well technology and estimate the impact of horizontal wells on present and future domestic oil recovery and reserves. Accomplishments for this quarter are presented.

McDonald, W.J.

1994-06-01T23:59:59.000Z

137

Horizontal oil well applications and oil recovery assessment. Volume 2: Applications overview, Final report  

SciTech Connect (OSTI)

Horizontal technology has been applied in over 110 formations in the USA. Volume 1 of this study addresses the overall success of horizontal technology, especially in less-publicized formations, i.e., other than the Austin Chalk, Bakken, and Niobrara. Operators in the USA and Canada were surveyed on a formation-by-formation basis by means of a questionnaire. Response data were received describing horizontal well projects in 58 formations in the USA and 88 in Canada. Operators` responses were analyzed for trends in technical and economic success based on lithology (clastics and carbonates) and resource type (light oil, heavy oil, and gas). The potential impact of horizontal technology on reserves was also estimated. A forecast of horizontal drilling activity over the next decade was developed.

Deskins, W.G.; McDonald, W.J.; Knoll, R.G.; Springer, S.J.

1995-03-01T23:59:59.000Z

138

Horizontal well will be employed in hydraulic fracturing research  

SciTech Connect (OSTI)

This paper reports on 10-well research site, planned to enable more controlled experiments for better definition of hydraulic fracturing. One of the 10 wells will be a near-horizontal well that will monitor microseismic events along its length. The Gas Research Institute (GR) has begun evaluating a low-permeability, gas-bearing sandstone as the target stratum for experiments to be conducted at its hydraulic fracture test site (HFTS). During a 4-year period, GRI will use the HFTS as a field laboratory to conduct multi-disciplinary research projects to assess the mechanics of hydraulic fracturing. As a result of a screening process the Davis sandstone in the Ft. Worth basin has emerged as the tight gas sand which best fits the selected criteria established by GRI and its contractors, GRI says. The Ft. Worth basin is located approximately 50 miles northwest of Ft. Worth. GRI is planning a research well to fully characterize the Davis prior to making a final decision on the location of the HFTS. If data from the research well indicate the Davis sand does not adequately meet selection criteria, other candidates identified in the screening process will be investigated.

Not Available

1991-05-20T23:59:59.000Z

139

Enhanced boiling heat transfer in horizontal test bundles  

SciTech Connect (OSTI)

Two-phase flow boiling from bundles of horizontal tubes with smooth and enhanced surfaces has been investigated. Experiments were conducted in pure refrigerant R-113, pure R-11, and mixtures of R-11 and R-113 of approximately 25, 50, and 75% of R-113 by mass. Tests were conducted in two staggered tube bundles consisting of fifteen rows and five columns laid out in equilateral triangular arrays with pitch-to-diameter ratios of 1.17 and 1.5. The enhanced surfaces tested included a knurled surface (Wolverine`s Turbo-B) and a porous surface (Linde`s High Flux). Pool boiling tests were conducted for each surface so that reference values of the heat transfer coefficient could be obtained. Boiling heat transfer experiments in the tube bundles were conducted at pressures of 2 and 6 bar, heat flux values from 5 to 80 kW/m{sup 2}s, and qualities from 0% to 80%, Values of the heat transfer coefficients for the enhanced surfaces were significantly larger than for the smooth tubes and were comparable to the values obtained in pool boiling. It was found that the performance of the enhanced tubes could be predicted using the pool boiling results. The degradation in the smooth tube heat transfer coefficients obtained in fluid mixtures was found to depend on the difference between the molar concentration in the liquid and vapor.

Trewin, R.R.; Jensen, M.K.; Bergles, A.E.

1994-08-01T23:59:59.000Z

140

Proton irradiation effect on SCDs  

E-Print Network [OSTI]

The Low Energy X-ray Telescope is a main payload on the Hard X-ray Modulation Telescope satellite. The swept charge device is selected for the Low Energy X-ray Telescope. As swept charge devices are sensitive to proton irradiation, irradiation test was carried out on the HI-13 accelerator at the China Institute of Atomic Energy. The beam energy was measured to be 10 MeV at the SCD. The proton fluence delivered to the SCD was $3\\times10^{8}\\mathrm{protons}/\\mathrm{cm}^{2}$ over two hours. It is concluded that the proton irradiation affects both the dark current and the charge transfer inefficiency of the SCD through comparing the performance both before and after the irradiation. The energy resolution of the proton-irradiated SCD is 212 eV@5.9 keV at $-60\\,^{\\circ}\\mathrm{C}$, while it before irradiated is 134 eV. Moreover, better performance can be reached by lowering the operating temperature of the SCD on orbit.

Yan-Ji Yang; Jing-Bin Lu; Yu-Sa Wang; Yong Chen; Yu-Peng Xu; Wei-Wei Cui; Wei Li; Zheng-Wei Li; Mao-Shun Li; Xiao-Yan Liu; Juan Wang; Da-Wei Han; Tian-Xiang Chen; Cheng-Kui Li; Jia Huo; Wei Hu; Yi Zhang; Bo Lu; Yue Zhu; Ke-Yan Ma; Di Wu; Yan Liu; Zi-Liang Zhang; Guo-He Yin; Yu Wang

2014-04-19T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

INTERNATIONAL RELATIONS &INTERNATIONAL RELATIONS &INTERNATIONAL RELATIONS & THE GLOBAL ECONOMYTHE GLOBAL ECONOMYTHE GLOBAL ECONOMY  

E-Print Network [OSTI]

GLOBAL ECONOMYTHE GLOBAL ECONOMY This major offers students rigorous interdisciplinary training 331: The Global Economy 2030 -- Examination of key ideas from economics, demography and technology. Guest lecturers illuminate possible conditions of the global economy in 2030. IR 454: International

Krylov, Anna I.

142

Engineering the global ecosystem  

E-Print Network [OSTI]

of humans deliberately engineering agricultural landscapes.010-0302-8 EDITORIAL Engineering the global ecosystemtale about human explorers engineering the ecosystem of Mars

Stringfellow, William T.; Jain, Ravi

2010-01-01T23:59:59.000Z

143

Global Nuclear Security  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Global Nuclear Security Both DOE and the National Nuclear Security Administration are working to reduce the risk of nuclear proliferation and provide technologies to improve...

144

Subsidizing Global Solar Power.  

E-Print Network [OSTI]

?? With national cuts on solar PV subsidies and the current “oversupply” of panels, the global solar market is clearly threatened by a contraction. Yet,… (more)

Arnesson, Daniel

2013-01-01T23:59:59.000Z

145

Particle seeding flow system for horizontal shock tube  

SciTech Connect (OSTI)

The Extreme Fluids Team in P-23, Physics Division, studies fluid dynamics at high speeds using high resolution diagnostics. The unsteady forces on a particle driven by a shock wave are not well understood, and they are difficult to model. A horizontal shock tube (HST) is being modified to collect data about the behavior of particles accelerated by shocks. The HST has been used previously for studies of Richtmyer-Meshkov instability using Planar Laser-Induced Fluorescence (PLIF) as well as Particle Image Velocimetry (PIV), diagnostics that measure density and velocity. The purpose of our project is to design a flow system that will introduce particles into the HST. The requirements for this particle flow system (PFS) are that it be non-intrusive, be able to introduce either solid or liquid particles, have an exhaust capability, not interfere with existing diagnostics, and couple with the existing HST components. In addition, the particles must flow through the tube in a uniform way. We met these design criteria by first drawing the existing shock tube and diagnostics and doing an initial design of the ducts for the PFS. We then estimated the losses through the particle flow system from friction and researched possible fans that could be used to drive the particles. Finally, the most challenging component of the design was the coupling to the HST. If we used large inlets, the shock would lose strength as it passed by the inlet, so we designed a novel coupling inlet and outlet that minimize the losses to the shock wave. Our design was reviewed by the Extreme Fluids Team, and it is now being manufactured and built based upon our technical drawings.

Johnston, Stephen [Los Alamos National Laboratory; Garcia, Nicolas J. [Los Alamos National Laboratory; Martinez, Adam A. [Los Alamos National Laboratory; Orlicz, Gregory C. [Los Alamos National Laboratory; Prestridge, Katherine P. [Los Alamos National Laboratory

2012-08-01T23:59:59.000Z

146

Global Development Our Responsibility  

E-Print Network [OSTI]

of expertise cover urgent global issues such as food production, energy supply, climate change, biodiversity e ort to address urgent global issues particularly a ecting developing countries e.g. climate change of Communication, 2012 · Project Leader: Karin Nilsson · Graphic Design: Viktor Wrange & Michael Kvick Cover Photo

147

CHILLING CONSIDERATIONS GLOBAL WARMING  

E-Print Network [OSTI]

(millionsofsquarekilometers) 30 20 10 MELTING OF GREENLAND ICE CAP Satellite determination of maximum extent of glacial melt Complete melt of the Greenland ice sheet would raise the level of the global ocean 23 feet. ASAN Steffen IS INCREASING Global carbon dioxide concentration over the last thousand years Polar ice cores #12;Mann et al

Schwartz, Stephen E.

148

Global Change Sustainability  

E-Print Network [OSTI]

Global Change and Sustainability Center The GCSC is an inclusionary and interdisciplinary hub that promotes, coordinates, and conducts local to global environmental- and sustainability-related research to complex environmental and sustainability issues and challenges. 2012 Annual Report #12;1GCSC 2012 ANNUAL

Tipple, Brett

149

The DC field components of horizontal and vertical electric dipole sources immersed in three-layered stratified media  

E-Print Network [OSTI]

for the solution in the case of horizontal electric dipole (HED) radiation source and the single-component HertzThe DC field components of horizontal and vertical electric dipole sources immersed in three- ponents of the static (DC) fields of horizontal electric dipoles ( HEDs) and vertical electric dipoles

Boyer, Edmond

150

Neutron irradiation of beryllium pebbles  

SciTech Connect (OSTI)

Seven subcapsules from the FFTF/MOTA 2B irradiation experiment containing 97 or 100% dense sintered beryllium cylindrical specimens in depleted lithium have been opened and the specimens retrieved for postirradiation examination. Irradiation conditions included 370 C to 1.6 {times} 10{sup 22} n/cm{sup 2}, 425 C to 4.8 {times} 10{sup 22} n/cm{sup 2}, and 550 C to 5.0 {times} 10{sup 22} n/cm{sup 2}. TEM specimens contained in these capsules were also retrieved, but many were broken. Density measurements of the cylindrical specimens showed as much as 1.59% swelling following irradiation at 500 C in 100% dense beryllium. Beryllium at 97% density generally gave slightly lower swelling values.

Gelles, D.S.; Ermi, R.M. [Pacific Northwest National Lab., Richland, WA (United States); Tsai, H. [Argonne National Lab., IL (United States)

1998-03-01T23:59:59.000Z

151

Comparison of day and night vehicular speeds on horizontal curves on rural two-lane highways  

E-Print Network [OSTI]

the magnitude of the difference between daytime and nighttime speeds is small for all degrees of curvature, a variable accounting for light condition is not needed for operating-speedbased profile modeling for horizontal alignment design consistency evaluation....

Guzman, Jesus

1996-01-01T23:59:59.000Z

152

Temperature Prediction Model for Horizontal Well with Multiple Fractures in Shale Reservoir  

E-Print Network [OSTI]

Fracture diagnostics is a key technology for well performance prediction of a horizontal well in a shale reservoir. The combination of multiple fracture diagnostic techniques gives reliable results, and temperature data has potential to provide more...

Yoshida, Nozomu

2013-04-12T23:59:59.000Z

153

Interpreting Horizontal Well Flow Profiles and Optimizing Well Performance by Downhole Temperature and Pressure Data  

E-Print Network [OSTI]

be used to obtain downhole flow conditions, which is key information to control and optimize horizontal well production. However, the fluid flow in the reservoir is often multiphase and complex, which makes temperature and pressure interpretation very...

Li, Zhuoyi

2011-02-22T23:59:59.000Z

154

Heat transfer during film condensation of potassium vapor on a horizontal plate  

E-Print Network [OSTI]

The object of the investigation is to analyze the following two features of heat transfer during condensation of potassium vapor: a. Heat transfer during film condensation of a pure saturated potassium vapor on a horizontal ...

Meyrial, Paul M.

1968-01-01T23:59:59.000Z

155

PREDICTION OF CUTTINGS BED HEIGHT WITH COMPUTATIONAL FLUID DYNAMICS IN DRILLING HORIZONTAL AND HIGHLY DEVIATED WELLS  

E-Print Network [OSTI]

PREDICTION OF CUTTINGS BED HEIGHT WITH COMPUTATIONAL FLUID DYNAMICS IN DRILLING HORIZONTAL parameters such as wellbore geometry, pump rate, drilling fluid rheology and density, and maximum drilling Computational Fluid Dynamics methods. Movement, concentration and accumulation of drilled cuttings in non

Ullmer, Brygg

156

The Effect of Whole Body Horizontal Vibration in Position Sense and Dynamic Stability of the Spine  

E-Print Network [OSTI]

at the 5 Hz frequency. These results would suggest that horizontal vibration may be less of a factor in whole-body vibration induced injuries. This work was supported by University of Kansas Transportation Research Institute Grant Program....

Lamis, Farhana

2008-06-09T23:59:59.000Z

157

Growth and Transfer of Monolithic Horizontal ZnO Nanowire Superstructures onto Flexible Substrates  

E-Print Network [OSTI]

, and electromechanical nanodevices, such as UV lasers,[2] light-emitting diodes,[3,4] field- emission devices,[5] solar of the NWs. Furthermore, by encapsulating the NW arrays with a polymer thin film, the horizontal NW arrays

Wang, Zhong L.

158

The impact of long-distance horizontal gene transfer on prokaryotic genome size  

E-Print Network [OSTI]

Horizontal gene transfer (HGT) is one of the most dominant forces molding prokaryotic gene repertoires. These repertoires can be as small as ?200 genes in intracellular organisms or as large as ?9,000 genes in large, ...

Cordero Sanchez, Otto Xavier

159

Horizontal Inequity and Vertical Redistribution with Indirect Taxes: the Greek Case  

E-Print Network [OSTI]

license issue fee and an initial registration tax, varying according to the vehicle’s engine power and technology. Cars are also subject to an annual transport due, also varying according to engine power. Stamp duties are levied on a large number... preferences, while improvements in vertical redistribution can be achieved, albeit at the cost of increased horizontal inequity. Keywords: distributional effect of taxes, horizontal inequality, vertical redistribution, indirect tax reform, Greece JEL...

Kaplanoglou, G; Newbery, David

160

Evaluation of a slotted orifice plate flow meter using horizontal two phase flow  

E-Print Network [OSTI]

EVALUATION OF A SLOTTED ORIFICE PLATE FLOW METER USING HORIZONTAL TWO PHASE FLOW A Thesis by ANITA ELENA FLORES Submitted to the Office of Graduate Studies of Texas ARM University in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE December 2000 Major Subject: Mechanical Engineering EVALUATION OF A SLOTTED ORIFICE PLATE FLOW METER USING HORIZONTAL TWO PHASE FLOW A Thesis by ANITA ELENA FLORES Submitted to Texas A&M University in partial fulfillment...

Flores, Anita Elena

2000-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

An experimental study of horizontal barrier formation and containment of NAPLs by gelling liquids  

E-Print Network [OSTI]

[1990], much of the research on this topic can be found only in copies of company reports. Aul and Cervtk [1979] developed a method for grouting horizontal drainage holes in coalbeds. Karol [1990] noted that there has been a growing acceptance... grout for plugging horizontal methane-drainage holes. Lowther and Gabr [1997] experimented with urethane, a different grout, for the formation of hydraulic barriers. Voss et al. [1994] and May et al. [1986] studied chemical grouts for constructing...

Durmusoglu, Ertan

2012-06-07T23:59:59.000Z

162

The drilling of a horizontal well in a mature oil field  

SciTech Connect (OSTI)

This report documents the drilling of a medium radius horizontal well in the Bartlesville Sand of the Flatrock Field, Osage County, Oklahoma by Rougeot Oil and Gas Corporation (Rougeot) of Sperry, Oklahoma. The report includes the rationale for selecting the particular site, the details of drilling the well, the production response, conclusions reached, and recommendations made for the future drilling of horizontal wells. 11 figs., 2 tabs.

Rougeot, J.E.; Lauterbach, K.A.

1991-01-01T23:59:59.000Z

163

Relationship between design speed and operating speed at horizontal curves on suburban arterials  

E-Print Network [OSTI]

RELATIONSHIP BETWEEN DESIGN SPEED AND OPERATING SPEED AT HORIZONTAL CURVES ON SUBURBAN ARTERIALS A Thesis by CARL BRIAN SHAMBURGER Submitted to the OIIice of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE December 1995 Major Subject: Civil Engineering RELATIONSHIP BETWEEN DESIGN SPEED AND OPERATING SPEED AT HORIZONTAL CURVES ON SUBURBAN ARTERIALS A Thesis by CARL BRIAN SHAMBURGER Submitted to Texas A&M University...

Shamburger, Carl Brian

2012-06-07T23:59:59.000Z

164

Global warming, bad weather, insurance losses and the global economy  

SciTech Connect (OSTI)

Global warming causes extremely bad weather in the near term. The impact on the insurance industry is described. Why global warming in the near term causes very bad weather is explained. The continuing trend of very bad weather and the future impact on the insurance industry is explored. How very bad weather can affect the global financial market is explained. Taking a historical view of the development of the modern economy, the authors describe in the near term the impact of global warming on the global economy. The long term impact of global warming on the global economy and the human race is explored. Opportunities presented by global warming are described.

Low, N.C. [UOB Life Assurance Ltd., Singapore (Singapore); Shen, S. [Global Warming International Center, Woodridge, IL (United States)

1996-09-01T23:59:59.000Z

165

Low energy electron irradiation of an apple  

E-Print Network [OSTI]

The viability of pathogenic organisms on the surface of fresh fruits and vegetables can be significantly reduced by low energy electron beam irradiation. The most difficult technical challenge for surface irradiation of fruits and vegetable...

Brescia, Giovanni Batista

2002-01-01T23:59:59.000Z

166

Statistical criteria for characterizing irradiance time series.  

SciTech Connect (OSTI)

We propose and examine several statistical criteria for characterizing time series of solar irradiance. Time series of irradiance are used in analyses that seek to quantify the performance of photovoltaic (PV) power systems over time. Time series of irradiance are either measured or are simulated using models. Simulations of irradiance are often calibrated to or generated from statistics for observed irradiance and simulations are validated by comparing the simulation output to the observed irradiance. Criteria used in this comparison should derive from the context of the analyses in which the simulated irradiance is to be used. We examine three statistics that characterize time series and their use as criteria for comparing time series. We demonstrate these statistics using observed irradiance data recorded in August 2007 in Las Vegas, Nevada, and in June 2009 in Albuquerque, New Mexico.

Stein, Joshua S.; Ellis, Abraham; Hansen, Clifford W.

2010-10-01T23:59:59.000Z

167

sterilization by irradiation Arne Miller  

E-Print Network [OSTI]

-1:2006 Equipment characterization (6) Product definition (7) Process definition (8) Installation Qualification (9.1) Operational Qualification (9.2) · Performance Qualification (9.3) - later #12;3 Equipment characterization samples shall be irradiated to defined and uniform doses. #12;9 9.1 Installation qualification (A.9

168

Low temperature irradiation tests on  

E-Print Network [OSTI]

Sample cool down by He gas loop 10K ­ 20K Fast neutron flux Measured by Ni activation in 2010 1.4xK #12;reactor Cryogenics #12;Al-Cu-Mg He gas temperature near sample 12K Resistance changesLow temperature irradiation tests on stabilizer materials using reactor neutrons at KUR Makoto

McDonald, Kirk

169

China's Global Oil Strategy  

E-Print Network [OSTI]

nations began to seek out oil reserves around the world. 3on the limited global oil reserves and spiking prices. Manyto the largest proven oil reserves, making up 61 percent of

Thomas, Bryan G

2009-01-01T23:59:59.000Z

170

KRFTWRK – Global Human Electricity  

E-Print Network [OSTI]

Power Network 2.1.1 Virtual Power Plants The Global Powernetwork, based on "Virtual Power Plants", called "VPP". A "participant runs a virtual human power plant. Per every "

Prohaska, Rainer

2009-01-01T23:59:59.000Z

171

China's Global Oil Strategy  

E-Print Network [OSTI]

21, 2008. Ying, Wang. “ China, Venezuela firms to co-developoilfields. ” China Daily (27 August 2005) http://David and Bi Jianhai. “China’s Global Hunt for Energy. ”

Thomas, Bryan G

2009-01-01T23:59:59.000Z

172

Global Cool Cities Alliance  

Broader source: Energy.gov [DOE]

The Department of Energy (DOE) is currently supporting the Global Cool Cities Alliance (GCCA), a non-profit organization that works with cities, regions, and national governments to speed the...

173

Global warming elucidated  

SciTech Connect (OSTI)

The meaning of global warming and its relevance to everyday life is explained. Simple thermodynamics is used to predict an oscillatory nature of the change in climate due to global warming. Global warming causes extreme events and bad weather in the near term. In the long term it may cause the earth to transition to another equilibrium state through many oscillation in climatic patterns. The magnitudes of these oscillations could easily exceed the difference between the end points. The author further explains why many no longer fully understands the nature and magnitudes of common phenomena such as storms and wind speeds because of these oscillations, and the absorptive properties of clouds. The author links the increase in duration of the El Nino to global warming, and further predicts public health risks as the earth transitions to another equilibrium state in its young history.

Shen, S. [Global Warming International Center, Woodridge, IL (United States)

1995-03-01T23:59:59.000Z

174

Irradiation-induced phenomena in carbon  

E-Print Network [OSTI]

Chapter 1 Irradiation-induced phenomena in carbon nanotubes To appear in "Chemistry of Carbon@acclab.helsinki.fi 1 #12;2CHAPTER 1. IRRADIATION-INDUCED PHENOMENA IN CARBON NANOTUBES #12;Contents 1 Irradiation-induced phenomena in carbon nanotubes 1 1.1 Introduction

Krasheninnikov, Arkady V.

175

Transition from Irradiation-Induced Amorphization to Crystallization...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

from Irradiation-Induced Amorphization to Crystallization in Nanocrystalline Silicon Carbide. Transition from Irradiation-Induced Amorphization to Crystallization in...

176

Occlusion-Aware Hessians for Error Control in Irradiance Caching /  

E-Print Network [OSTI]

Control for Irradiance Caching. ” In ACM Transactions on Graphics,Control for Irradiance Caching. ” In ACM Transactions on Graphics,

Schwarzhaupt, Jorge Andres

2013-01-01T23:59:59.000Z

177

GE Global Research News | GE Global Research  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun with Big Sky Learning Fun with Big SkyDIII-D Performance ToolsGlobal

178

GLOBAL GOVERNANCE FIGHTING POVERTY 26 GLOBAL AGENDA 2003  

E-Print Network [OSTI]

, they would discover a nearly total disparity between global commitments and domestic politics. Bush hasGLOBAL GOVERNANCE FIGHTING POVERTY 26 GLOBAL AGENDA 2003 the world promised to put real resources credible document spelling out the US role in a global war against AIDS. The planned US financial

179

Solar turbulence in earth's global and regional temperature anomalies Nicola Scafetta,1,2  

E-Print Network [OSTI]

Solar turbulence in earth's global and regional temperature anomalies Nicola Scafetta,1,2 Paolo a study of the influence of solar activity on the earth's temperature. In particular, we focus on the repercussion of the fluctuations of the solar irradiance on the temperature of the Northern and Southern

Scafetta, Nicola

180

Original article Predicted global warming  

E-Print Network [OSTI]

Original article Predicted global warming and Douglas-fir chilling requirements DD McCreary1 DP to predicted global warming. Douglas-fir / chilling / global warming / bud burst / reforestation Résumé offer evidence that mean global warming of 3-4 °C could occur within the next century, particularly

Boyer, Edmond

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

The Tourism Global Value Chain  

E-Print Network [OSTI]

The Tourism Global Value Chain ECONOMIC UPGRADING AND WORKFORCE DEVELOPMENT Michelle Christian 2011 CENTER on GLOBALIZATION, GOVERNANCE & COMPETITIVENESS #12;The Tourism Global Value Chain: Economic: November 17, 2011 #12;The Tourism Global Value Chain: Economic Upgrading and Workforce Development i Table

Richardson, David

182

GTL-1 Irradiation Summary Report  

SciTech Connect (OSTI)

The primary objective of the Gas Test Loop (GTL-1) miniplate experiment is to confirm acceptable performance of high-density (i.e., 4.8 g-U/cm3) U3Si2/Al dispersion fuel plates clad in Al-6061 and irradiated under the relatively aggressive Booster Fast Flux Loop (BFFL) booster fuel conditions, namely a peak plate surface heat flux of 450 W/cm2. As secondary objectives, several design and fabrication variations were included in the test matrix that may have the potential to improve the high-heat flux, high-temperature performance of the base fuel plate design.1, 2 The following report summarizes the life of the GTL-1 experiment through end of irradiation, including as-run neutronic analysis, thermal analysis and hydraulic testing results.

D. M. Perez; G. S. Chang; N. E. Woolstenhulme; D. M. Wachs

2012-01-01T23:59:59.000Z

183

Condensation of Refrigerant-11 on the outside of horizontal and inclined enhanced tubes  

SciTech Connect (OSTI)

Heat transfer condensation tests with Refrigerant-11 were performed on the outside of a smooth tube and a variety of enhanced tubes oriented horizontally and at various tube inclinations. One smooth tube and seven enhanced (externally fluted, roped, spiraled, and externally finned) tubes of 2.54-cm (1-in.) nominal outside diameter and 1.17-m (4-ft) length were tested. Several of the tested tubes featured internal enhanced geometries, which were caused by the heat transfer enhancing geometry on the tube's external surface. Condensing heat transfer coefficients are reported as composite coefficients, which combine the resistance of the condensing film and the tube wall, and are based on total tube outside surface area. Results show that in the horizontal condensing mode, the rank order (best to worst) of the tube geometries tested was spiral-shaped tubes, rope-shaped tubes, smooth tube, externally finned tube, and externally fluted tube. For a spiral-shaped tube, horizontal composite coefficients were up to 2.0 times the corresponding horizontal smooth tube values. For tilt angles greater than or equal to 60/sup 0/ from the horizontal, the condensing performance of the externally fluted tube was best of all the tubes tested.

Domingo, N.

1982-12-01T23:59:59.000Z

184

RERTR-6 Irradiation Summary Report  

SciTech Connect (OSTI)

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-6 was designed to evaluate several modified fuel designs that were proposed to address the possibility of breakaway swelling due to porosity within the (U. Mo) Al interaction product observed in the full-size plate tests performed in Russia and France1. The following report summarizes the life of the RERTR-6 experiment through end of irradiation, including as-run neutronic analyses, thermal analyses and hydraulic testing results.

D. M. Perez; M. A. Lillo; G. S. Chang; G. A. Roth; N. E. Woolstenhulme; D. M. Wachs

2011-12-01T23:59:59.000Z

185

RERTR-13 Irradiation Summary Report  

SciTech Connect (OSTI)

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-13 was designed to assess performance of different types of neutron absorbers that can be potentially used as burnable poisons in the low enriched uranium-molybdenum based dispersion and monolithic fuels.1 The following report summarizes the life of the RERTR-13 experiment through end of irradiation, including as-run neutronic analysis results, thermal analysis results and hydraulic testing results.

D. M. Perez; M. A. Lillo; G. S. Chang; D. M. Wachs; G. A. Roth; N. E. Woolstenhulme

2012-09-01T23:59:59.000Z

186

Nuclear plant irradiated steel handbook  

SciTech Connect (OSTI)

This reference handbook presents selected information extracted from the EPRI reactor surveillance program database, which contains the results from surveillance program reports on 57 plants and 116 capsules. Tabulated data includes radiation induced temperature shifts, capsule irradiation conditions and statistical features of the Charpy V-notch curves. General information on the surveillance materials is provided and the Charpy V-notch energy results are presented graphically.

Oldfield, W.; Oldfield, F.M.; Lombrozo, P.M.; McConnell, P.

1986-09-01T23:59:59.000Z

187

Global ice sheet modeling  

SciTech Connect (OSTI)

The University of Maine conducted this study for Pacific Northwest Laboratory (PNL) as part of a global climate modeling task for site characterization of the potential nuclear waste respository site at Yucca Mountain, NV. The purpose of the study was to develop a global ice sheet dynamics model that will forecast the three-dimensional configuration of global ice sheets for specific climate change scenarios. The objective of the third (final) year of the work was to produce ice sheet data for glaciation scenarios covering the next 100,000 years. This was accomplished using both the map-plane and flowband solutions of our time-dependent, finite-element gridpoint model. The theory and equations used to develop the ice sheet models are presented. Three future scenarios were simulated by the model and results are discussed.

Hughes, T.J.; Fastook, J.L. [Univ. of Maine, Orono, ME (United States). Institute for Quaternary Studies

1994-05-01T23:59:59.000Z

188

Long range global warming  

SciTech Connect (OSTI)

This paper explores one of the causes of global warming that is often overlooked, the direct heating of the environment by engineering systems. Most research and studies of global warming concentrate on the modification that is occurring to atmospheric air as a result of pollution gases being added by various systems; i.e., refrigerants, nitrogen oxides, ozone, hydrocarbons, halon, and others. This modification affects the thermal radiation balance between earth, sun and space, resulting in a decrease of radiation outflow and a slow rise in the earth`s steady state temperature. For this reason the solution to the problem is perceived as one of cleaning up the processes and effluents that are discharged into the environment. In this paper arguments are presented that suggest, that there is a far more serious cause for global warming that will manifest itself in the next two or three centuries; direct heating from the exponential growth of energy usage by humankind. Because this is a minor contributor to the global warming problem at present, it is overlooked or ignored. Energy use from the combustion of fuels and from the output of nuclear reactions eventually is manifest as warming of the surroundings. Thus, as energy is used at an ever increasing rate the consequent global warming also increases at an ever increasing rate. Eventually this rate will become equal to a few percent of solar radiation. When this happens the earth`s temperature will have risen by several degrees with catastrophic results. The trends in world energy use are reviewed and some mathematical models are presented to suggest future scenarios. These models can be used to predict when the global warming problem will become undeniably apparent, when it will become critical, and when it will become catastrophic.

Rolle, K.C.; Pulkrabek, W.W.; Fiedler, R.A. [Univ. of Wisconsin, Platteville, WI (United States)

1995-12-31T23:59:59.000Z

189

Explicit global integrators  

E-Print Network [OSTI]

be advantageous. For this purpose, forward interpolation utilizing Radau Quadrature will be employed. An explicit method of global integration has been developed to estimate a solution to a differential equation. A set of functions P (x), P (x), , P (x) and a... set of points n+1 x , x , , x can be found such that n+1 r x n+1 f(u)du = g P. (x)i'(x. ) 0 i=1 for all x when f(u) is a polynomial of degree n or less. The above process is described by Axelsson as global integration. In . th the cases...

Merriam, Robert Stevens

2012-06-07T23:59:59.000Z

190

INTERNATIONAL RELATIONSINTERNATIONAL RELATIONSINTERNATIONAL RELATIONS (GLOBAL BUSINESS)(GLOBAL BUSINESS)(GLOBAL BUSINESS)  

E-Print Network [OSTI]

INTERNATIONAL RELATIONSINTERNATIONAL RELATIONSINTERNATIONAL RELATIONS (GLOBAL BUSINESS)(GLOBAL BUSINESS)(GLOBAL BUSINESS) Future leaders in business, government, and law need to understand how global, and internship opportunities, it is an ideal major for those interested in entering the realms of business

Krylov, Anna I.

191

Case study of a horizontal well in a layered Rotliegendes gas field  

SciTech Connect (OSTI)

A horizontal well was drilled in the Ravenspurn North field to drain a thin gas column above the aquifer. The field has a significant variation in reservoir quality, with most of the wells requiring stimulation by hydraulic fracturing. The reservoir is formed from a stacked sequence of aeolian dune and fluvial sandstones with a wide permeability range. The horizontal well was chosen as an alternative to stimulation by hydraulic fracturing to avoid water production from the aquifer. The well was successful, flowing at higher gas rates than expected with no water production. Production, core, and production logging data were used to demonstrate greater than expected lateral heterogeneity in the field. The horizontal well was found to be appropriate for the very specific conditions found in one part of the reservoir; however, the overall development strategy of using hydraulic fracture remains the preferred technique.

Catterall, S.J.A.; Yaliz, A. (Hamilton Oil Co. Ltd., London (United Kingdom))

1995-02-01T23:59:59.000Z

192

Development of an inflow performance relationship (IPR) for a slanted/horizontal well  

SciTech Connect (OSTI)

Since 1968, the Vogel equation has been used extensively and successfully for analyzing the inflow performance relationship (IPR) of flowing oil wells under solution-gas drive. Oil well productivity can be rapidly estimated using the Vogel IPR curve and well outflow performance. However, the Vogel curve was originally developed for conventional vertical wells and may not be valid for slanted and horizontal wells. This report presents the development of IPR's for slanted and horizontal wells by using a vertical/horizontal/slanted well reservoir simulator. The generated IPR's are found to be similar to the parabolic characteristic of the Vogel curve. Several application examples are included to illustrate the use of the newly generated curves. 12 refs., 15 figs., 25 tabs.

Cheng, A.M.

1990-03-01T23:59:59.000Z

193

Development of general inflow performance relationships (IPR's) for slanted and horizontal wells producing heterogeneous solution-gas drive reservoirs  

SciTech Connect (OSTI)

Since 1968, the Vogel equation has been used extensively and successfully for analyzing the inflow performance relationship (IPR) of flowing vertical wells producing by solution-gas drive. Oil well productivity can be rapidly estimated by using the Vogel IPR curve and well outflow performance. With recent interests on horizontal well technology, several empirical IPRs for solution-gas drive horizontal and slanted wells have been developed under homogeneous reservoir conditions. This report presents the development of IPRs for horizontal and slanted wells by using a special vertical/horizontal/slanted well reservoir simulator under six different reservoir and well parameters: ratio of vertical to horizontal permeability, wellbore eccentricity, stratification, perforated length, formation thickness, and heterogeneous permeability. The pressure and gas saturation distributions around the wellbore are examined. The fundamental physical behavior of inflow performance for horizontal wells is described.

Cheng, A.M.

1992-04-01T23:59:59.000Z

194

CHILLING CONSIDERATIONS GLOBAL WARMING  

E-Print Network [OSTI]

CHANGE AND ENERGY USE IN TODAY'S WORLD #12;Brookhaven National Laboratory's Speakers' Bureau · Community, Ph.D. Climate Change and Energy Use in Today's World Some Chilling Considerations About Global owned by the U.S. Department of Energy's Office of Science, which provides most of the Lab

Schwartz, Stephen E.

195

Global Lightning Observations  

E-Print Network [OSTI]

;Climatology: Basics · 5 years of OTD, 6 years of LIS data · Adjusted for detection efficiency J.Atmos. Oc · Global flash rate: 45 fl / sec ± 10% J. Geophys. Res., 2003 #12;High Resolution Full Climatology Annual (4/95-3/00) and LIS (1/98-12/03) instruments #12;#12;#12;Climatology: Diurnal cycle ( Local hour

California at Berkeley, University of

196

global warming's six americas  

E-Print Network [OSTI]

Vehicles & Solar Panels 23 Regulating CO2 as a Pollutant 24 A 20 Percent National Renewable Energy Standard the spring and fall of 2012. Perceived Benefits and Costs of Reducing Fossil Fuel Use and Global Warming Introduction 5 The Six Americas Audience Segments 6 Changes in the Size of Segments 7 Perceived Benefits

Haller, Gary L.

197

Patterns in Global Hydrothermal  

E-Print Network [OSTI]

Patterns in Global Hydrothermal Activity noaa ocean exploration Presenter: Edward T. Baker #12) High-T vents High = hydrothermal discharge Low = active or inactive discharge sites B. Davy, GNS NZ #12 Lc(km) #12;Future Directions Quantify processes: ·Employ or develop new technologies (AUVs, solid

198

Global Threat Reduction Initiative  

E-Print Network [OSTI]

Global Threat Reduction Initiative ­ Conversion Program: Reduced Enrichment for Research and Test the dual application of splitting the atom, U.S. policy towards civilian use of highly enriched uranium and test reactors fueled first with low enriched uranium (LEU) and then later with HEU. By the early 1970s

Kemner, Ken

199

Global Health Seminar Series  

E-Print Network [OSTI]

Bay Area Global Health Seminar Series Monday, January 27, 2014 2:30pm ­ 4:00pm (Reception to follow at the Center for Health Policy and the Woods Institute for the Environment. He studies how economic, political, and natural environments affect population health in developing countries using a mix of experimental

Klein, Ophir

200

GLOBAL TAXONOMY INITIATIVE  

E-Print Network [OSTI]

#12;THE GLOBAL TAXONOMY INITIATIVE: Using Systematic Inventories to Meet Country and Regional Needs International #12;Table of Contents Introduction 1 I. Using Inventories to Build Capacity and Advance the GTI 2 for systematic inventories. A major component of the workshop addressed how systematic inventories can serve

Grant, Taran

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Global Biodiversity Conservation Priorities  

E-Print Network [OSTI]

Global Biodiversity Conservation Priorities T. M. Brooks,1,2,3 * R. A. Mittermeier,1 G. A. B. da is essential to minimize biodiversity loss. To address this need, biodiversity conservation organizations have conservation funding. H uman actions are causing a biodiversity crisis, with species extinction rates up

Wilmers, Chris

202

Global Climate & Catastrophic Risk  

E-Print Network [OSTI]

Global Climate & Catastrophic Risk Forum 2012 A Joint Program with LA RIMS Education Day Rethinking Catastrophic Risk in Risk Management: Earthquake-Related Challenges Featuring: Keynote Speaker Dr. Frank Beuthin, Willis Group Holdings Plc. Yohei Miyamoto, Aon Risk Solutions Curtis deVera, Marsh

de Lijser, Peter

203

Method and apparatus for drilling horizontal holes in geological structures from a vertical bore  

DOE Patents [OSTI]

This invention is directed to a method and apparatus for drilling horizontal holes in geological strata from a vertical position. The geological structures intended to be penetrated in this fashion are coal seams, as for in situ gasification or methane drainage, or in oil-bearing strata for increasing the flow rate from a pre-existing well. Other possible uses for this device might be for use in the leaching of uranium ore from underground deposits or for introducing horizontal channels for water and steam injections.

Summers, David A. (Rolla, MO); Barker, Clark R. (Rolla, MO); Keith, H. Dean (Rolla, MO)

1982-01-01T23:59:59.000Z

204

Low-mass evolution from HE ignition to beyond the horizontal branch  

SciTech Connect (OSTI)

The evolution of an 0.6 M/sub solar mass/ stellar model during core helium burning is presented. Following the off-center ignition of helium in the core flash, the star remains on the red giant branch for > 10/sup 6/ years, undergoing twelve additional flashes. After leaving the giant branch, the star evolves on the horizontal branch for 8.15 x 10/sup 7/ years before returning to the giant branch and undergoing strong helium-shell flashes. The implications for horizontal branch and RR Lyrae stars are discussed.

Despain, K.

1980-01-01T23:59:59.000Z

205

EPR Investigation of Irradiated Curry Powder  

SciTech Connect (OSTI)

Gamma-ray irradiated curry powder, a well priced oriental spice was investigated in order to establish the ability of EPR to detect the presence and time stability of free irradiation free-radicals. Accordingly, curry powder aliquots were irradiated with gradually increasing absorbed doses up to 11.3 kGy. The EPR spectra of all irradiated samples show the presence of al last two different species of free radicals, whose concentration increased monotonously with the absorbed doses. A 100 deg. C isothermal annealing of irradiated samples has shown a differential reduction of amplitude of various components of the initial spectra, but even after 3.6 h of thermal treatment, the remaining amplitude represents no less then 30% of the initial ones. The same peculiarities have been noticed after more than one year storage at room temperature, all of them being very useful in establishing the existence of any previous irradiation treatment.

Duliu, O. G.; Ali, S. I. [University of Bucharest, Department of Atomic and Nuclear Physics, P.O. Box MG-11, 077125 Bucharest (Romania); Georgescu, R. [National Institute for Physics and Nuclear Engineering-Horia Hulubei, P.O. Box MG-6, 077125 Bucharest (Romania)

2007-04-23T23:59:59.000Z

206

Sodium and potassium levels in the serum of acutely irradiated and non-irradiated rats  

E-Print Network [OSTI]

SODIUM AND POTASSIUM LEVELS IN THE SERUM OF ACUTELY IRRADIATED AND NON-IRRADIATED RATS A Thesis By DAVID PRESTON SHEPHERD Submitted to the Graduate College of the Texas ARM University in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE August 1967 Major Subject: Zoology SODIUM AND POTASSIUM LEVELS IN THE SERUM OF ACUTELY IRRADIATED AND NON-IRRADIATED RATS A Thesis By DAVID PRESTON SHEPHERD Approved as to style and content by: (Chairman of Committee) (Head...

Shepherd, David Preston

1967-01-01T23:59:59.000Z

207

Global interrupt and barrier networks  

DOE Patents [OSTI]

A system and method for generating global asynchronous signals in a computing structure. Particularly, a global interrupt and barrier network is implemented that implements logic for generating global interrupt and barrier signals for controlling global asynchronous operations performed by processing elements at selected processing nodes of a computing structure in accordance with a processing algorithm; and includes the physical interconnecting of the processing nodes for communicating the global interrupt and barrier signals to the elements via low-latency paths. The global asynchronous signals respectively initiate interrupt and barrier operations at the processing nodes at times selected for optimizing performance of the processing algorithms. In one embodiment, the global interrupt and barrier network is implemented in a scalable, massively parallel supercomputing device structure comprising a plurality of processing nodes interconnected by multiple independent networks, with each node including one or more processing elements for performing computation or communication activity as required when performing parallel algorithm operations. One multiple independent network includes a global tree network for enabling high-speed global tree communications among global tree network nodes or sub-trees thereof. The global interrupt and barrier network may operate in parallel with the global tree network for providing global asynchronous sideband signals.

Blumrich, Matthias A. (Ridgefield, CT); Chen, Dong (Croton-On-Hudson, NY); Coteus, Paul W. (Yorktown Heights, NY); Gara, Alan G. (Mount Kisco, NY); Giampapa, Mark E (Irvington, NY); Heidelberger, Philip (Cortlandt Manor, NY); Kopcsay, Gerard V. (Yorktown Heights, NY); Steinmacher-Burow, Burkhard D. (Mount Kisco, NY); Takken, Todd E. (Mount Kisco, NY)

2008-10-28T23:59:59.000Z

208

The Carnal Global Sex for Sale on the Global Market  

E-Print Network [OSTI]

The Carnal Global Economy: Sex for Sale on the Global Market Sarah Gormady POLT 762 Spring 2009 #12;Human Trafficking is: Process + Way/Means + Goal A Global Free Market James Tassie #12;Commonwealth Queens Brothel Total Monthly Revenue $72,480 Total Operating Expenses $21,780 Gross Profit $50

New Hampshire, University of

209

Low-drag electrical contact arrangement for maintaining continuity between horizontally movable members  

DOE Patents [OSTI]

This invention is a low-drag electrical contact arrangement for establishing continuity between upper and lower spaced members which are subject to relative horizontal movement. In one aspect, the invention comprises an electrical commutating arrangement which includes a horizontally disposed linear electrical commutator. A horizontally movable electrically conductive pedestal is positioned below the commutator and defines a clearance therewith. The pedestal is formed with a cavity confronting the commutator. In the cavity is a bead of electrical conductive liquid, the bead being characterized by an upwardly convex meniscus portion which extends across the clearance and contacts the commutator. The surface tension of the bead is sufficient to maintain the bead intact when the commutator and pedestal are displaced horizontally at speeds from zero to at least twelve inches a minute. This arrangement provides a significant advance in highly precise machining processes, such as diamond-turning, where precision is limited by the drag imposed by conventional commutators of the carbon-brush type.

Brown, R. Jack (Clinton, TN); Gerth, Howard L. (Knoxville, TN); Robinson, Samuel C. (Clinton, TN)

1982-01-01T23:59:59.000Z

210

Low-drag electrical-contact arrangement for maintaining continuity between horizontally movable members  

DOE Patents [OSTI]

This invention is a low-drag electrical contact arrangement for establishing continuity between upper and lower spaced members which are subject to relative horizontal movement. In one aspect, the invention comprises an electrical commutating arrangement which includes a horizontally disposed linear electrical commutator. A horizontally movable electrically conductive pedestal is positioned below the commutator and defines a clearance therewith. The pedestal is formed with a cavity confronting the commutator. In the cavity is a bead of electrical conductive liquid, the bead being characterized by an upwardly convex meniscus portion which extends across the clearance and contacts the commutator. The surface tension of the bead is sufficient to maintain the bead intact when the commutator and pedestal are displaced horizontally at speeds from zero to at least twelve inches a minute. This arrangement provides a significant advance in highly precise machining processes, such as diamond-turning, where precision is limited by the drag imposed by conventional commutators of the carbon-brush type.

Brown, R.J.; Gerth, H.L.; Robinson, S.C.

1981-01-23T23:59:59.000Z

211

Under consideration for publication in J. Fluid Mech. 1 Stressed horizontal convection  

E-Print Network [OSTI]

in the Gullmarfjord on the west coast of Sweden. When the wind swept over the fjord, the water at the surface flowed to the suggestion of Munk & Wunsch (1998) that mechanical energy sources -- such as the wind stress observed by Sandstr¨om (1908) -- are necessary to sustain the ocean circulation. Recent work on horizontal convection

Young, William R.

212

Hydraulic Fracturing and Horizontal Gas Well Drilling Reference List Updated December 7, 2011  

E-Print Network [OSTI]

Hydraulic Fracturing and Horizontal Gas Well Drilling Reference List Updated December 7, 2011. References to popular press and advocacy groups, both of which are numerous and described in detail elsewhere of Hydraulic Fracturing in the Shale Plays (2010). Tudor Pickering Holt & Co with Reservoir Research Partners

Manning, Sturt

213

Horizontal Heat Exchanger Design and Analysis for Passive Heat Removal Systems  

SciTech Connect (OSTI)

This report describes a three-year project to investigate the major factors of horizontal heat exchanger performance in passive containment heat removal from a light water reactor following a design basis accident LOCA (Loss of Coolant Accident). The heat exchanger studied in this work may be used in advanced and innovative reactors, in which passive heat removal systems are adopted to improve safety and reliability The application of horizontal tube-bundle condensers to passive containment heat removal is new. In order to show the feasibility of horizontal heat exchangers for passive containment cooling, the following aspects were investigated: 1. the condensation heat transfer characteristics when the incoming fluid contains noncondensable gases 2. the effectiveness of condensate draining in the horizontal orientation 3. the conditions that may lead to unstable condenser operation or highly degraded performance 4. multi-tube behavior with the associated secondary-side effects This project consisted of two experimental investigations and analytical model development for incorporation into industry safety codes such as TRAC and RELAP. A physical understanding of the flow and heat transfer phenomena was obtained and reflected in the analysis models. Two gradute students (one funded by the program) and seven undergraduate students obtained research experience as a part of this program.

Vierow, Karen

2005-08-29T23:59:59.000Z

214

Compact fluorescent lamp using horizontal and vertical insulating septums and convective venting geometry  

DOE Patents [OSTI]

A novel design is described for a compact fluorescent lamp, including a lamp geometry which will increase light output and efficacy of the lamp in a base down operating position by providing horizontal and vertical insulating septums positioned in the ballast compartment of the lamp to provide a cooler coldspot. Selective convective venting provides additional cooling of the ballast compartment. 9 figs.

Siminovitch, M.

1998-02-10T23:59:59.000Z

215

Evolution of Red Algal Plastid Genomes: Ancient Architectures, Introns, Horizontal Gene Transfer, and  

E-Print Network [OSTI]

Evolution of Red Algal Plastid Genomes: Ancient Architectures, Introns, Horizontal Gene Transfer, Station Biologique, Roscoff, France Abstract Red algae have the most gene-rich plastid genomes known across all available red algal plastid genomes we show they all share a highly compact and slowly

Martone, Patrick T.

216

Analysis of wellbore instability in vertical, directional, and horizontal wells using field data  

E-Print Network [OSTI]

Analysis of wellbore instability in vertical, directional, and horizontal wells using field data M.A-mail addresses: mamuddin@kfupm.edu.sa (M.A. Mohiuddin), aazeez@kfupm.edu.sa (A. Abdulraheem). 0920-4105/$ - see. Mohiuddin, K. Khan, A. Abdulraheem , A. Al-Majed, M.R. Awal Center for Petroleum and Minerals, Research

Al-Majed, Abdulaziz Abdullah

217

Heat Transfer Measurements for a Horizontal Micro-Tube Using Liquid Crystal Thermography  

E-Print Network [OSTI]

62 TC02-007 Heat Transfer Measurements for a Horizontal Micro-Tube Using Liquid Crystal-tube and 1000m micro-tube. In the single-phase heat transfer experiments, the fully-developed flow heat transfer were also measured using thermocouples (TC). The results showed that the heat transfer coefficient

Ghajar, Afshin J.

218

Horizontal low-void retorting of eastern and western oil shale  

SciTech Connect (OSTI)

Horizontal in situ retorting processes have been developed to recover oil from thin, shallow oil shale deposits. To date the most successful field tests have been conducted in Green River oil shale located in Utah. Consideration is being given to applying this technology to the New Albany oil shales in Indiana. Western Research Institute (WRI) conducted two horizontal in situ oil shale experiments using eastern oil shale and the results are compared with results obtained from a similar experiment using Green River oil shale. The objectives of the three experiments were to simulate the horizontal retorting process and determine oil yield, retorting zone profiles and product characteristics using alternative operating conditions for eastern and western oil shales. The tests proved that horizontal retorting could be simulated in the laboratory. However, air bypass problems occurred in the experiments, which probably reduced oil recovery compared with recovery from field tests. During the eastern oil shale tests plugging was encountered in the gas recovery system because of the production of a solid material containing sulfur compounds. This plugging could be a potential problem for future laboratory and field experimentation. The oil produced from eastern oil shale has different properties from western shale oil. The oil is highly aromatic and when hydrogenated may yield a prototype high density jet fuel. 10 refs., 8 figs., 11 tabs.

Fahy, L.J.

1986-02-01T23:59:59.000Z

219

CEBAF UPGRADE CRYOMODULE COMPONENT TESTING IN THE HORIZONTAL TEST BED (HTB)*  

E-Print Network [OSTI]

CEBAF UPGRADE CRYOMODULE COMPONENT TESTING IN THE HORIZONTAL TEST BED (HTB)* I. E. Campisi , B The planned upgrade of the CEBAF electron accelerator includes the development of an improved cryomodule. Several components differ substantially from the original CEBAF cryomodule; these include: the new 7-cell

220

A comparative analysis of numerical simulation and analytical modeling of horizontal well cyclic steam injection  

E-Print Network [OSTI]

of assuming them to be the same (as in the original model of Gunadi). Main results of the comparative analysis for both cases of horizontal well positions are as follows. First, the water production rates are in very close agreement with results...

Ravago Bastardo, Delmira Cristina

2005-08-29T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

A parametric study on the benefits of drilling horizontal and multilateral wells in coalbed methane reservoirs  

SciTech Connect (OSTI)

Recent years have witnessed a renewed interest in development of coalbed methane (CBM) reservoirs. Optimizing CBM production is of interest to many operators. Drilling horizontal and multilateral wells is gaining Popularity in many different coalbed reservoirs, with varying results. This study concentrates on variations of horizontal and multilateral-well configurations and their potential benefits. In this study, horizontal and several multilateral drilling patterns for CBM reservoirs are studied. The reservoir parameters that have been studied include gas content, permeability, and desorption characteristics. Net present value (NPV) has been used as the yard stick for comparing different drilling configurations. Configurations that have been investigated are single-, dual-, tri-, and quad-lateral wells along with fishbone (also known as pinnate) wells. In these configurations, the total length of horizontal wells and the spacing between laterals (SBL) have been studied. It was determined that in the cases that have been studied in this paper (all other circumstances being equal), quadlateral wells are the optimum well configuration.

Maricic, N.; Mohaghegh, S.D.; Artun, E. [Chevron Energy Technology Co., Houston, TX (USA)

2008-12-15T23:59:59.000Z

222

Antitrust Evaluation of Horizontal Mergers: An Economic Alternative to Market Definition  

E-Print Network [OSTI]

Antitrust Evaluation of Horizontal Mergers: An Economic Alternative to Market Definition 25 between the two firm's products. We argue that our approach is well grounded in economics, workable, Economics and Regulation at Northwestern University and the FTC First Annual Microeconomic Conference

Sadoulet, Elisabeth

223

Productivity and injectivity of horizontal wells. Annual report, March 10, 1996--March 9, 1997  

SciTech Connect (OSTI)

Progress is reported on the following tasks: advanced modeling of horizontal wells; heterogeneous effects of reservoirs; development of improved methods for calculating multi-phase pressure drops within the wellbore; pseudo-functions; development of multi-well models;testing of HW models with field examples; enhanced oil recovery applications; and application studies and their optimization.

Aziz, K.; Hewett, T.A.; Arbabi, S.; Smith, M.

1997-06-01T23:59:59.000Z

224

3.4 SIMULATED HORIZONTAL WELL PERFORMANCE IN THE NATURALLY FRACTURED SPRABERRY TREND AREA  

E-Print Network [OSTI]

Waterflood Pilot was performed using commercial VIP and ECLIPSE simulators. A pilot model was developed using of performance between horizontal and vertical wells with different average reservoir pressures. (2) (Guevara, 1988). The individual beds rarely exceed 15 ft in thickness. Reservoir characterization

Schechter, David S.

225

Response of a slotted plate flow meter to horizontal two phase flow  

E-Print Network [OSTI]

meter is always better in performance and accuracy than the standard orifice plate flow meter. This study is primarily based on how a slotted plate responds to horizontal two-phase flow with air and water being used as the working fluids. The plates...

Muralidharan, Vasanth

2005-02-17T23:59:59.000Z

226

A Comparison of Vehicle Speed at Day and Night Rural Horizontal Curves  

E-Print Network [OSTI]

This thesis documents the linear mixed model developed for vehicle speed along two-lane two-way rural horizontal curves in the outside lane. Speed data at each curve was collected at four points along the curve including the midpoint of the curve...

Quaium, Ridwan B.

2010-07-14T23:59:59.000Z

227

Multidisciplinary Design Optimization for Glass-Fiber Epoxy-Matrix Composite 5 MW Horizontal-Axis  

E-Print Network [OSTI]

-Axis Wind-Turbine Blades M. Grujicic, G. Arakere, B. Pandurangan, V. Sellappan, A. Vallejo, and M. Ozen optimization, fatigue-life assessment, horizon- tal axis wind turbine blades 1. Introduction The depletion for the development of cost-effective glass-fiber reinforced epoxy-matrix composite 5 MW horizontal-axis wind-turbine

Grujicic, Mica

228

THE DEVIL’S STAIRCASE DIMENSIONS AND MEASURE-THEORETICAL ENTROPY OF MAPS WITH HORIZONTAL GAP  

E-Print Network [OSTI]

Abstract. This work elucidates the measure-theoretical entropy and dimensions of a unimodal map with a horizontal gap. The measure-theoretical entropy and dimensions of the Ft (which is defined later)are shown to form a devil’s staircase structure with respect to the gap size t. Pesin’s formula for gap maps is also considered. 1.

Jung-chao Ban; Song-sun Lin

229

Global climate feedbacks  

SciTech Connect (OSTI)

The important physical, chemical, and biological events that affect global climate change occur on a mesoscale -- requiring high spatial resolution for their analysis. The Department of Energy has formulated two major initiatives under the US Global Change Program: ARM (Atmospheric Radiation Measurements), and CHAMMP (Computer Hardware Advanced Mathematics and Model Physics). ARM is designed to use ground and air-craft based observations to document profiles of atmospheric composition, clouds, and radiative fluxes. With research and models of important physical processes, ARM will delineate the relationships between trace gases, aerosol and cloud structure, and radiative transfer in the atmosphere, and will improve the parameterization of global circulation models. The present GCMs do not model important feedbacks, including those from clouds, oceans, and land processes. The purpose of this workshop is to identify such potential feedbacks, to evaluate the uncertainties in the feedback processes (and, if possible, to parameterize the feedback processes so that they can be treated in a GCM), and to recommend research programs that will reduce the uncertainties in important feedback processes. Individual reports are processed separately for the data bases.

Manowitz, B.

1990-10-01T23:59:59.000Z

230

Global residential appliance standards  

SciTech Connect (OSTI)

In most countries, residential electricity consumption typically ranges from 20% to 40% of total electricity consumption. This energy is used for heating, cooling, refrigeration and other end-uses. Significant energy savings are possible if new appliance purchases are for models with higher efficiency than that of existing models. There are several ways to ensure or encourage such an outcome, for example, appliance rebates, innovative procurement, and minimum efficiency standards. This paper focuses on the latter approach. At the present time, the US is the only country with comprehensive appliance energy efficiency standards. However, many other countries, such as Australia, Canada, the European Community (EC), Japan and Korea, are considering enacting standards. The greatest potential impact of minimum efficiency standards for appliances is in the developing countries (e.g., China and India), where saturations of household appliances are relatively low but growing rapidly. This paper discusses the potential savings that could be achieved from global appliance efficiency standards for refrigerators and freezers. It also could be achieved from global appliance efficiency standards for refrigerators and freezers. It also discusses the impediments to establishing common standards for certain appliance types, such as differing test procedures, characteristics, and fuel prices. A methodology for establishing global efficiency standards for refrigerators and freezers is described.

Turiel, I.; McMahon, J.E. (Lawrence Berkeley Lab., CA (United States)); Lebot, B. (Agence Francaise pour la Maitrise de l'Energie, Valbonne (France))

1993-03-01T23:59:59.000Z

231

Is an Alternative Globalization Possible?  

E-Print Network [OSTI]

Global Democracy. 94. Amartya Sen, Development as Freedom (trump card. Recently, Amartya Sen’s “capability approach” 94

Evans, Peter

2009-01-01T23:59:59.000Z

232

Globalization, Labor, Transformation of Work  

E-Print Network [OSTI]

in an Increasingly Global Economy Edited by Jonathan H. Westover THE ORGANISATION #12;First published in Australia in an increasingly global economy Jonathan H. Westover (editor) Bibliography. 978 1 86335 660 2 (pbk.) 978 1 86335 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Economic Globalization and Caribbean Economies, Syed H. Akhter, Paul Pounder

233

GLOBAL WARMING THE GREENHOUSE EFFECT  

E-Print Network [OSTI]

GLOBAL WARMING THE GREENHOUSE EFFECT AND YOUR FAMILY'S CONTRIBUTION TO IT Stephen E. Schwartz GREENHOUSE EFFECT #12;GLOBAL ENERGY BALANCE Global and annual average energy fluxes in watts per square meter about it.But nobody does anything about it. ­ Mark Twain­ Mark Twain Now with the greenhouse effect, we

Schwartz, Stephen E.

234

Global Warming: Connecting the Dots  

E-Print Network [OSTI]

Global Warming: Connecting the Dots from Causes to Solutions* Jim Hansen 26 February 2007 National://www.columbia.edu/~jeh1/worldwatch_nov2006.pdf) 5. Communicating dangers and opportunities in global warming, Amer-16, 2006. (http://pubs.giss.nasa.gov/docs/2006/2006_Hansen.pdf) 8. Global warming: Connecting the dots from

Hansen, James E.

235

4, 10591092, 2007 Global warming  

E-Print Network [OSTI]

BGD 4, 1059­1092, 2007 Global warming potential of agro-ecosystems S. Lehuger et al. Title Page Predicting the global warming potential of agro-ecosystems S. Lehuger, B. Gabrielle, E. Larmanou, P. Laville Correspondence to: S. Lehuger (simon.lehuger@grignon.inra.fr) 1059 #12;BGD 4, 1059­1092, 2007 Global warming

Paris-Sud XI, Université de

236

Agricultural Sciences for Global Development  

E-Print Network [OSTI]

's areas of expertise cover other urgent global issues such as energy supply, climate change, biodiversity, like food security and climate change, are truly global. The global arena is changing fast therefore and the environment in developing countries. Our research is conducted in close cooperation with partners in a large

237

Thinking about global climate change  

SciTech Connect (OSTI)

Opinions regarding issues related to global climate change are presented. The focus is on socioeconomic and historical aspects. World War II is discussed as an intellectual and emotional turning point in global issues, and global climate change is identified as a possible turning point of similar significance. Political, scientific, and public points of view regarding the issue are discussed.

Russell, M. [Univ. of Tennessee, Knoxville, TN (United States); [Oak Ridge National Lab., TN (United States)

1992-12-31T23:59:59.000Z

238

Analytical and Numerical Solutions for the Case of a Horizontal Well with a Radial Power-Law Permeability Distribution--Comparison to the Multi-Fracture Horizontal Case  

E-Print Network [OSTI]

............................................................................ 26 3.9 Log-log plot of the analytical pD solutions at tD=105 for a horizontal well producing at a constant rate, centered in a radial composite reservoir with a power-law permeability distribution in the inner region... for numerical simulation (radial increment = 2 cm) ............................................ 40 4.2 Log-log plot of qD vs. tD for a PPR with rs = 75 ft and a MFH with xf = 75 ft and 10 md-ft fracture conductivity...

Broussard, Ryan Sawyer

2013-02-08T23:59:59.000Z

239

Bachaquero-01 reservoir, Venezuela-increasing oil production by switching from cyclic steam injection to steamflooding using horizontal wells  

E-Print Network [OSTI]

cyclic steam injection and steamflooding. The Cartesian model dimensions of the three horizontal welts were 11x22x4, 11x27x5, and 12x20x5. In the steamflooding scheme investigated, the existing horizontal welts were used as injectors while existing (and...

Rodriguez, Manuel Gregorio

1999-01-01T23:59:59.000Z

240

Heat Waves, Global Warming, and Mitigation  

E-Print Network [OSTI]

Heat Waves, Global Warming, and Mitigation Ann E. Carlson*2008]HEAT WAVES, GLOBAL WARMING, AND MITIGATION 175 stroke2001). 2008]HEAT WAVES, GLOBAL WARMING, AND MITIGATION 177

Carlson, Ann E.

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Global Warming, endogenous risk and irreversibility  

E-Print Network [OSTI]

The economics of global warming, Institute for InternationalEconomic Models of Global Warming, Cambridge, Mass. MITstochastic losses from global warming, Risk Analysis 16(2):

Fisher, Anthony C.; Narain, Urvashi

2002-01-01T23:59:59.000Z

242

Nuclear Engineering Division Irradiated Materials Laboratory  

E-Print Network [OSTI]

Nuclear Engineering Division Irradiated Materials Laboratory The Irradiated Materials Laboratory (IML) in Argonne's Nuclear Engineering Division is used to conduct research on the behavior. #12;C O N TA C T > Dr. Michael C. Billone | 630-252-7146 | billone@anl.gov | Nuclear Engineering

Kemner, Ken

243

AGC-1 Irradiation Experiment Test Plan  

SciTech Connect (OSTI)

The Advanced Graphite Capsule (AGC) irradiation test program supports the acquisition of irradiated graphite performance data to assist in the selection of the technology to be used for the VHTR. Six irradiations are planned to investigate compressive creep in graphite subjected to a neutron field and obtain irradiated mechanical properties of vibrationally molded, extruded, and iso-molded graphites for comparison. The experiments will be conducted at three temperatures: 600, 900, and 1200°C. At each temperature, two different capsules will be irradiated to different fluence levels, the first from 0.5 to 4 dpa and the second from 4 to 7 dpa. AGC-1 is the first of the six capsules designed for ATR and will focus on the prismatic fluence range.

R. L. Bratton

2006-05-01T23:59:59.000Z

244

Irradiation-induced defect clustering and amorphization in silicon...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Irradiation-induced defect clustering and amorphization in silicon carbide. Irradiation-induced defect clustering and amorphization in silicon carbide. Abstract: Previous computer...

245

Neutron Irradiation of Hydrided Cladding Material in HFIR Summary...  

Broader source: Energy.gov (indexed) [DOE]

Neutron Irradiation of Hydrided Cladding Material in HFIR Summary of Initial Activities Neutron Irradiation of Hydrided Cladding Material in HFIR Summary of Initial Activities...

246

Magnetization measurements and XMCD studies on ion irradiated...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

measurements and XMCD studies on ion irradiated iron oxide and core-shell ironiron-oxide nanomaterials. Magnetization measurements and XMCD studies on ion irradiated iron oxide...

247

Timeline | GE Global Research  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation Desert Southwest RegionatSearchScheduled System BurstLong TermScience&Time-ResolvedGlobal

248

The Global Energy Challenge  

ScienceCinema (OSTI)

The expected doubling of global energy demand by 2050 challenges our traditional patterns of energy production, distribution and use.   The continued use of fossil fuels raises concerns about supply, security, environment and climate.  New routes are needed for the efficient conversion of energy from chemical fuel, sunlight, and heat to electricity or hydrogen as an energy carrier and finally to end uses like transportation, lighting, and heating. Opportunities for efficient new energy conversion routes based on nanoscale materials will be presented, with emphasis on the sustainable energy technologies they enable.

George Crabtree

2010-01-08T23:59:59.000Z

249

Sandia National Laboratories: Global  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -theErik Spoerke SSLS Exhibit at ExploraGlobal Sandia Co-Hosts "Climate Risk

250

Sandia National Laboratories: Global  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -theErik Spoerke SSLS Exhibit at ExploraGlobal Sandia Co-Hosts "Climate

251

RERTR-7 Irradiation Summary Report  

SciTech Connect (OSTI)

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-7A, was designed to test several modified fuel designs to target fission densities representative of a peak low enriched uranium (LEU) burnup in excess of 90% U-235 at peak experiment power sufficient to generate a peak surface heat flux of approximately 300 W/cm2. The RERTR-7B experiment was designed as a high power test of 'second generation' dispersion fuels at peak experiment power sufficient to generate a surface heat flux on the order of 230 W/cm2.1 The following report summarizes the life of the RERTR-7A and RERTR-7B experiments through end of irradiation, including as-run neutronic analyses, thermal analyses and hydraulic testing results.

D. M. Perez; M. A. Lillo; G. S. Chang; G. A. Roth; N. E. Woolstenhulme; D. M. Wachs

2011-12-01T23:59:59.000Z

252

Global tree network for computing structures enabling global processing operations  

DOE Patents [OSTI]

A system and method for enabling high-speed, low-latency global tree network communications among processing nodes interconnected according to a tree network structure. The global tree network enables collective reduction operations to be performed during parallel algorithm operations executing in a computer structure having a plurality of the interconnected processing nodes. Router devices are included that interconnect the nodes of the tree via links to facilitate performance of low-latency global processing operations at nodes of the virtual tree and sub-tree structures. The global operations performed include one or more of: broadcast operations downstream from a root node to leaf nodes of a virtual tree, reduction operations upstream from leaf nodes to the root node in the virtual tree, and point-to-point message passing from any node to the root node. The global tree network is configurable to provide global barrier and interrupt functionality in asynchronous or synchronized manner, and, is physically and logically partitionable.

Blumrich; Matthias A. (Ridgefield, CT); Chen, Dong (Croton-On-Hudson, NY); Coteus, Paul W. (Yorktown Heights, NY); Gara, Alan G. (Mount Kisco, NY); Giampapa, Mark E. (Irvington, NY); Heidelberger, Philip (Cortlandt Manor, NY); Hoenicke, Dirk (Ossining, NY); Steinmacher-Burow, Burkhard D. (Mount Kisco, NY); Takken, Todd E. (Mount Kisco, NY); Vranas, Pavlos M. (Bedford Hills, NY)

2010-01-19T23:59:59.000Z

253

AGC-1 Post Irradiation Examination Status  

SciTech Connect (OSTI)

The Next Generation Nuclear Plant (NGNP) Graphite R&D program is currently measuring irradiated material property changes in several grades of nuclear graphite for predicting their behavior and operating performance within the core of new Very High Temperature Reactor (VHTR) designs. The Advanced Graphite Creep (AGC) experiment consisting of six irradiation capsules will generate this irradiated graphite performance data for NGNP reactor operating conditions. All six AGC capsules in the experiment will be irradiated in the Advanced Test Reactor (ATR), disassembled in the Hot Fuel Examination Facility (HFEF), and examined at the INL Research Center (IRC) or Oak Ridge National Laboratory (ORNL). This is the first in a series of status reports on the progress of the AGC experiment. As the first capsule, AGC1 was irradiated from September 2009 to January 2011 to a maximum dose level of 6-7 dpa. The capsule was removed from ATR and transferred to the HFEF in April 2011 where the capsule was disassembled and test specimens extracted from the capsules. The first irradiated samples from AGC1 were shipped to the IRC in July 2011and initial post irradiation examination (PIE) activities were begun on the first 37 samples received. PIE activities continue for the remainder of the AGC1 specimen as they are received at the IRC.

David Swank

2011-09-01T23:59:59.000Z

254

AGR-1 Irradiation Experiment Test Plan  

SciTech Connect (OSTI)

This document presents the current state of planning for the AGR-1 irradiation experiment, the first of eight planned irradiations for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. The objectives of the AGR-1 experiment are: 1. To gain experience with multi-capsule test train design, fabrication, and operation with the intent to reduce the probability of capsule or test train failure in subsequent irradiation tests. 2. To irradiate fuel produced in conjunction with the AGR fuel process development effort. 3. To provide data that will support the development of an understanding of the relationship between fuel fabrication processes, fuel product properties, and irradiation performance. In order to achieve the test objectives, the AGR-1 experiment will be irradiated in the B-10 position of the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). The test will contain six independently controlled and monitored capsules. Each capsule will contain a single type, or variant, of the AGR coated fuel. The irradiation is planned for about 700 effective full power days (approximately 2.4 calendar years) with a time-averaged, volume-average temperature of approximately 1050 °C. Average fuel burnup, for the entire test, will be greater than 17.7 % FIMA, and the fuel will experience fast neutron fluences between 2.4 and 4.5 x 1025 n/m2 (E>0.18 MeV).

John T. Maki

2009-10-01T23:59:59.000Z

255

Fracturing pressures and near-well fracture geometry of arbitrarily oriented and horizontal wells  

SciTech Connect (OSTI)

The hydraulic fracturing of arbitrarily oriented and horizontal wells is made challenging by the far more complicated near-well fracture geometry compared to that of conventional vertical wells. This geometry is important both for hydraulic fracture propagation and the subsequent post-treatment well performance. Fracture tortuosity of arbitrarily oriented and horizontal wells is likely to cause large initiation pressures and reduction in the fracture widths. This paper presents a comprehensive study of the effects of important variables, including the principal stresses, wellbore orientation, and perforation configuration on fracture geometry. Initiation pressures, the contact between arbitrarily oriented wells and the fracture plane, and the near-well fracture geometry are determined and discussed. This study also shows that because of the near-well stress concentration the fracture width at the wellbore is always smaller than the maximum fracture width. This can have important consequences during hydraulic fracturing.

Chen, Z.; Economides, M.J.

1995-12-31T23:59:59.000Z

256

Analysis of the D0 Crane Rail as a Support for a Horizontal Lifeline  

SciTech Connect (OSTI)

The D-Zero crane rail is analyzed for use as an anchor support for a one person Horizon{trademark} Horizontal Lifeline system that will span the pit area at D-Zero assembly hall. The lifeline will span 75 ft across the pit area, will be located out of the travel of the crane and above the concrete lentil wall. The crane rail is a suitable anchor for a one person Horizon TM Horizontal Lifeline system. The expected stress on the rail is 1,995 psi which has a factor of safety of 5.5 on the allowable stress. The anchor position is located 18 feet away from the concrete lentil wall and out of the travel of the overhead crane.

Cease, H.; /Fermilab

2000-03-02T23:59:59.000Z

257

Experimental evaluation of vertically versus horizontally split yokes for SSC (Superconducting Super Collider) dipole magnets  

SciTech Connect (OSTI)

The yoke in SSC dipole magnets provides mechanical support to the collared coil as well as serving as a magnetic element. The yoke and skin are used to increase the coil prestress and reduce collar deflections under excitation. Yokes split on the vertical or horizontal mid-plane offer different advantages in meeting these objectives. To evaluate the relative merits of the two configuration a 1.8 m model dipole was assembled and tested first with horizontally split and then with vertically split yoke laminations. The magnet was extensively instrumented to measure azimuthal and axial stresses in the coil and the cold mass skin resulting from cooldown and excitation. Mechanical behavior of this magnet with each configuration is compared with that of other long and short models and with calculations. 13 refs., 5 figs.

Strait, J.; Coulter, K.; Jaffery, T.; Kerby, J.; Koska, W.; Lamm, M.J.

1990-05-03T23:59:59.000Z

258

Shallow oil production using horizontal wells with enhanced oil recovery techniques  

SciTech Connect (OSTI)

Millions of barrels of oil exist in the Bartlesville formation throughout Oklahoma, Kansas, and Missouri. In an attempt to demonstrate that these shallow heavy oil deposits can be recovered, a field project was undertaken to determine the effectiveness of enhanced oil recovery techniques (EOR) employing horizontal wells. Process screening results suggested that thermal EOR processes were best suited for the recovery of this heavy oil. Screening criteria suggested that in situ combustion was a viable technique for the production of these reserves. Laboratory combustion tube tests confirmed that sufficient amounts of fuel could be deposited. The results of the in situ combustion field pilot were disappointing. A total overall recovery efficiency of only 16.0 percent was achieved. Results suggest that the combustion front might have moved past the horizontal well, however elevated temperatures or crude upgrading were not observed. Factors contributing to the lack of production are also discussed.

Satchwell, R.M.; Johnson, L.A. Jr. [Western Research Institute, Laramie, WY (United States); Trent, R. [Univ. of Alaska, Fairbanks, AK (United States)

1995-02-01T23:59:59.000Z

259

Integrated Approach Towards the Application of Horizontal Wells to Improve Waterflooding Performance  

SciTech Connect (OSTI)

This final report describes the progress during the six year of the project on ''Integrated Approach Towards the Application of Horizontal Wells to Improve Waterflooding Performance.'' This report is funded under the Department of Energy's (DOE's) Class I program which is targeted towards improving the reservoir performance of mature oil fields located in fluvially-dominated deltaic deposits. The project involves using an integrated approach to characterize the reservoir followed by drilling of horizontal injection wells to improve production performance. The project was divided into two budget periods. In the first budget period, many modern technologies were used to develop a detailed reservoir management plan; whereas, in the second budget period, conventional data was used to develop a reservoir management plan. The idea was to determine the cost effectiveness of various technologies in improving the performance of mature oil fields.

Kelkar, Mohan; Liner, Chris; Kerr, Dennis

1999-10-15T23:59:59.000Z

260

Prediction of refrigerant void fraction in horizontal tubes using probabilistic flow regime maps  

SciTech Connect (OSTI)

A state of the art review of two-phase void fraction models in smooth horizontal tubes is provided and a probabilistic two-phase flow regime map void fraction model is developed for refrigerants under condensation, adiabatic, and evaporation conditions in smooth, horizontal tubes. Time fraction information from a generalized probabilistic two-phase flow map is used to provide a physically based weighting of void fraction models for different flow regimes. The present model and void fraction models in the literature are compared to data from multiple sources including R11, R12, R134a, R22, R410A refrigerants, 4.26-9.58 mm diameter tubes, mass fluxes from 70 to 900 kg/m{sup 2} s, and a full quality range. The present model has a mean absolute deviation of 3.5% when compared to the collected database. (author)

Jassim, E.W.; Newell, T.A.; Chato, J.C. [Department of Mechanical Science and Engineering, University of Illinois at Urbana-Champaign, 1206 West Green Street, Urbana, IL 61801 (United States)

2008-04-15T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Termination for a superconducting power transmission line including a horizontal cryogenic bushing  

DOE Patents [OSTI]

A termination for a superconducting power transmission line is disclosed which is comprised of a standard air entrance insulated vertical bushing with an elbow, a horizontal cryogenic bushing linking the pressurized cryogenic cable environment to the ambient temperature bushing and a stress cone which terminates the cable outer shield and transforms the large radial voltage gradient in the cable dielectric into a much lower radial voltage gradient in the high density helium coolant at the cold end of the cryogenic bushing.

Minati, Kurt F. (Northport, NY); Morgan, Gerry H. (Patchogue, NY); McNerney, Andrew J. (Shoreham, NY); Schauer, Felix (Upton, NY)

1984-01-01T23:59:59.000Z

262

An evaluation of alternative horizontal curve design approaches for rural two-lane highways  

E-Print Network [OSTI]

documents an evaluation of the effects of superelevation on operating speeds and accident experience and the effects of side friction demand on accident experience at horizontal curves on rural two-lane highways. Variables considered in operating speed.... The hypothesis of this portion of the study was that the addition of superelevation would cause operating speeds to increase. Superelevation was found to have a significant influence on vehicle operating speeds. Potential accident surrogates examined included...

Voigt, Anthony Paul

1995-01-01T23:59:59.000Z

263

Horizontal cryogenic bushing for the termination of a superconducting power-transmission line  

DOE Patents [OSTI]

A termination for a superconducting power transmission line is disclosed which is comprised of a standard air entrance insulated vertical bushing with an elbow, a horizontal cryogenic bushing linking the pressurized cryogenic cable environment to the ambient temperature bushing and a stress cone which terminated the cable outer shield and transforms the large radial voltage gradient in the cable dielectric into a much lower radial voltage gradient in the high density helium coolant at the cold end of the cryogenic bushing.

Minati, K.F.; Morgan, G.H.; McNerney, A.J.; Schauer, F.

1982-07-29T23:59:59.000Z

264

Anais XI SBSR, Belo Horizonte, Brasil, 05 -10 abril 2003, INPE, p. 2193 -2200. MAPSAR: A NEW L-BAND SPACEBORNE SAR MISSION FOR ASSESSMENT  

E-Print Network [OSTI]

Anais XI SBSR, Belo Horizonte, Brasil, 05 - 10 abril 2003, INPE, p. 2193 - 2200. 2193 MAPSAR: A NEW the 9 7 38 4 #12;Anais XI SBSR, Belo Horizonte, Brasil, 05 - 10 abril 2003, INPE, p. 2193 - 2200. 2194

Domingues, Margarete Oliveira

265

Integrated approach towards the application of horizontal wells to improve waterflooding performance. Annual report  

SciTech Connect (OSTI)

This annual report describes the progress during the second year of the project on Integrated Approach Towards the Application of Horizontal Wells to Improve Waterflooding Performance. This project is funded under the Department of Energy`s Class I program which is targeted towards improving the reservoir performance of mature oil fields located in fluvial-dominated deltaic deposits. The project involves an integrated approach to characterize the reservoir followed by the drilling of horizontal injection wells to improve production performance. The type of data we have integrated include cross bore hole seismic surveys, geological interpretation based on logs and cores, and engineering information. This report covers the second phase of the project which includes a detailed reservoir description of the field by integrating all the available information, followed by flow simulation of the Self Unit under various operating conditions. Based on an examination of the various operating parameters, we observed that the best possible solution to improve the Self Unit performance is to recomplete and stimulate most of the wells followed by an increase in the water injection rate. Drilling of horizontal injection well, although helpful in improving the performance, was not found to be economically feasible. The proposed reservoir management plan will be implemented shortly.

Kelkar, M.; Liner, C.; Kerr, D.

1995-05-01T23:59:59.000Z

266

The application of a new polymer mud to horizontal drilling in the Dagang Oilfield  

SciTech Connect (OSTI)

A new kind of polymer muds, which is generally referred to as the amphionic polymer mud, has been applied to the two horizontal well drilling for the first time in the Dagang Oilfield, located in east China. In this mud system, two amphionic polymers are usually used as the main additives, the one with high molecular weight is an inhibitive encapsuler and filtration control agent, and the other one with low molecular weight is a deflocculant. The amphionic polymer, just as its name, is defined as the polymer that both organic cations and anions simultaneously exist in their molecular chains. The design criteria, formulations and properties of this mud system are discussed. As a case history, the field performance of this new polymer mud in the different sections of the second well (by name Guan H-1, a medium-radius horizontal well) is also given. It was shown from the laboratory and field tests that the amphionic polymer mud not only has all the advantages of the polymer muds commonly used, but is able to overcome the disadvantages of those muds, indicated by its highly inhibitive character while maintaining excellent mud performances. For this reason, the major drilling problems for horizontal wells in the Dagang Oilfield, such as hole cleaning, wellbore stability, lubricity, lost circulation and formation damage, which were hardly solved by the use of other water-based muds, could be solved successfully by the use of the amphionic polymer mud at much lower cost than the oil-based mud.

Yan, J.; Jiang, G.; Zong, R.

1995-10-01T23:59:59.000Z

267

Environmental Measurement-While-Drilling System and Horizontal Directional Drilling Technology Demonstration, Hanford Site  

SciTech Connect (OSTI)

The Environmental Measurement-While-Drilling (EMWD) system and Horizontal Directional Drilling (HDD) were successfully demonstrated at the Mock Tank Leak Simulation Site and the Drilling Technology Test Site, Hanford, Washington. The use of directional drilling offers an alternative to vertical drilling site characterization. Directional drilling can develop a borehole under a structure, such as a waste tank, from an angled entry and leveling off to horizontal at the desired depth. The EMWD system represents an innovative blend of new and existing technology that provides the capability of producing real-time environmental and drill bit data during drilling operations. The technology demonstration consisted of the development of one borehole under a mock waste tank at a depth of {approximately} {minus}8 m ({minus}27 ft.), following a predetermined drill path, tracking the drill path to within a radius of {approximately}1.5 m (5 ft.), and monitoring for zones of radiological activity using the EMWD system. The purpose of the second borehole was to demonstrate the capability of drilling to a depth of {approximately} {minus}21 m ({minus}70 ft.), the depth needed to obtain access under the Hanford waste tanks, and continue drilling horizontally. This report presents information on the HDD and EMWD technologies, demonstration design, results of the demonstrations, and lessons learned.

Williams, C.V.; Lockwood, G.J.; Normann, R.A.; Myers, D.A.; Gardner, M.G.; Williamson, T.; Huffman, J.

1999-06-01T23:59:59.000Z

268

Method for explosive expansion toward horizontal free faces for forming an in situ oil shale retort  

DOE Patents [OSTI]

Formation is excavated from within a retort site in formation containing oil shale for forming a plurality of vertically spaced apart voids extending horizontally across different levels of the retort site, leaving a separate zone of unfragmented formation between each pair of adjacent voids. Explosive is placed in each zone, and such explosive is detonated in a single round for forming an in situ retort containing a fragmented permeable mass of formation particles containing oil shale. The same amount of formation is explosively expanded upwardly and downwardly toward each void. A horizontal void excavated at a production level has a smaller horizontal cross-sectional area than a void excavated at a lower level of the retort site immediately above the production level void. Explosive in a first group of vertical blast holes is detonated for explosively expanding formation downwardly toward the lower void, and explosive in a second group of vertical blast holes is detonated in the same round for explosively expanding formation upwardly toward the lower void and downwardly toward the production level void for forming a generally T-shaped bottom of the fragmented mass.

Ricketts, Thomas E. (Bakersfield, CA)

1980-01-01T23:59:59.000Z

269

RERTR-12 Insertion 2 Irradiation Summary Report  

SciTech Connect (OSTI)

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-12 was designed to provide comprehensive information on the performance of uranium-molybdenum (U-Mo) based monolithic fuels for research reactor applications.1 RERTR-12 insertion 2 includes the capsules irradiated during the last three irradiation cycles. These capsules include Z, Y1, Y2 and Y3 type capsules. The following report summarizes the life of the RERTR-12 insertion 2 experiment through end of irradiation, including as-run neutronic analysis results, thermal analysis results and hydraulic testing results.

D. M. Perez; G. S. Chang; D. M. Wachs; G. A. Roth; N. E. Woolstenhulme

2012-09-01T23:59:59.000Z

270

Measuring Degradation Rates Without Irradiance Data  

SciTech Connect (OSTI)

A method to report PV system degradation rates without using irradiance data is demonstrated. First, a set of relative degradation rates are determined by comparing daily AC final yields from a group of PV systems relative to the average final yield of all the PV systems. Then, the difference between relative and absolute degradation rates is found from a statistical analysis. This approach is verified by comparing to methods that utilize irradiance data. This approach is significant because PV systems are often deployed without irradiance sensors, so the analysis method described here may enable measurements of degradation using data that were previously thought to be unsuitable for degradation studies.

Pulver, S.; Cormode, D.; Cronin, A.; Jordan, D.; Kurtz, S.; Smith, R.

2011-02-01T23:59:59.000Z

271

Global Studies Course List Fall 2010 (2111) COURSE LIST  

E-Print Network [OSTI]

...........................................................................5 2. Global Economy and Global Governance .................................................9 3 from one of six Global Concentrations (Sustainable Development; Global Economy and Global GovernanceGlobal Studies Course List ­ Fall 2010 (2111) Page 1 COURSE LIST Fall 2010 (2111) Global Studies

Jiang, Huiqiang

2111-01-01T23:59:59.000Z

272

Global Scratch Upgrade in Progress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

the facility is now positioned to meet the performance demands of all its clusters. By upgrading the consolidated Global Scratch, users will be able to continue taking advantage...

273

Environmental Regulation, Globalization, and Innovation  

E-Print Network [OSTI]

This essay explores the complex relationship between environmental regulation, innovation, and sustainable development within the context of an increasingly globalizing economy. It will be argued that industrial policy, ...

Ashford, Nicholas

2009-01-01T23:59:59.000Z

274

Machine Learning for Global Optimization  

E-Print Network [OSTI]

Noname manuscript No. (will be inserted by the editor). Machine Learning for Global Optimization. A. Cassioli?. · D. Di Lorenzo. ?. · M. Locatelli. ??. · F. Schoen.

schoen,,,

275

Global warming and global dioxide emission: An empirical study  

SciTech Connect (OSTI)

In this paper, the dynamic relationship between global surface temperature (global warming) and global carbon dioxide emission (CO{sub 2}) is modelled and analyzed by causality and spectral analysis in the time domain and frequency domain, respectively. Historical data of global CO{sub 2} emission and global surface temperature anomalies over 129 years from 1860-1988 are used in this study. The causal relationship between the two phenomena is first examined using the Sim and Granger causality test in the time domain after the data series are filtered by ARIMA models. The Granger causal relationship is further scrutinized and confirmed by cross-spectral and multichannel spectral analysis in the frequency domain. The evidence found from both analyses proves that there is a positive causal relationship between the two variables. The time domain analysis suggests that Granger causality exists between global surface temperature and global CO{sub 2} emission. Further, CO{sub 2} emission causes the change in temperature. The conclusions are further confirmed by the frequency domain analysis, which indicates that the increase in CO{sub 2} emission causes climate warming because a high coherence exists between the two variables. Furthermore, it is proved that climate changes happen after an increase in CO{sub 2} emission, which confirms that the increase in CO{sub 2} emission does cause global warming. 27 refs., 10 figs., 5 tabs.

Linyan Sun [Xian Jiaotong Univ., Shaanxi (China); Wang, M. [Saint Mary`s Univ., Halifax, Nova Scotia (Canada)

1996-04-01T23:59:59.000Z

276

CLIMATE CHANGE GLOBAL ECONOMY How to decarbonise the global economy  

E-Print Network [OSTI]

CLIMATE CHANGE · GLOBAL ECONOMY How to decarbonise the global economy Today's report on deep efforts of independent experts from 15 countries to find national pathways to making economies based-zero emissions sometime in the second half of this century. This deep cut should occur in a growing world economy

277

Introduction The bay scallop, Argopecten irradi-  

E-Print Network [OSTI]

71(3) 17 Introduction The bay scallop, Argopecten irradi- ans amplicostatus, has been present (Garcia-Cubas, 1968). Historical Uses Mollusks were used by the pre-Co- lumbian cultures in Mexico as food

278

Selective irradiation of the vascular endothelium  

E-Print Network [OSTI]

We developed a unique methodology to selectively irradiate the vascular endothelium in vivo to better understand the role of vascular damage in causing normal tissue radiation side-effects.The relationship between vascular ...

Schuller, Bradley W

2007-01-01T23:59:59.000Z

279

Processing Irradiated Beryllium For Disposal  

SciTech Connect (OSTI)

The purpose of this research was to develop a process for decontaminating irradiated beryllium that will allow it to be disposed of through normal radwaste channels. Thus, the primary objectives of this ongoing study are to remove the transuranic (TRU) isotopes to less than 100 nCi/g and remove {sup 60}Co, and {sup 137}Cs, to levels that will allow the beryllium to be contact handled. One possible approach that appears to have the most promise is aqueous dissolution and separation of the isotopes by selected solvent extraction followed by precipitation, resulting in a granular form for the beryllium that may be fixed to prevent it from becoming respirable and therefore hazardous. Beryllium metal was dissolved in nitric and fluorboric acids. Isotopes of {sup 241}Am, {sup 239}Pu, {sup 85}Sr, and {sup 137}Cs were then added to make a surrogate beryllium waste solution. A series of batch contacts was performed with the spiked simulant using chlorinated cobalt dicarbollide (CCD) and polyethylene glycol diluted with sulfone to extract the isotopes of Cs and Sr. Another series of batch contacts was performed using a combination of octyl (phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) in tributyl phosphate (TBP) diluted with dodecane for extracting the isotopes of Pu and Am. The results indicate that greater than 99.9% removal can be achieved for each isotope with only three contact stages.

T. J. Tranter; R. D. Tillotson; N. R. Mann; G. R. Longhurst

2005-11-01T23:59:59.000Z

280

Neutron Irradiation Measurement for Superconducting Magnet  

E-Print Network [OSTI]

close to reactor core · Sample cool down by He gas loop: 10K ­ 20K · Fast neutron flux (En>0.1MeV): 1.4x. Materials, 49, p161 (1973&74) Reactor n on Al Reactor n on Cu fluence up to 2*1022 n/m2 (En>0.1MeV) RRR Irradiation at KUR · Kyoto Univ. Research Reactor Institute · MW max. thermal power · Irradiation cryostat

McDonald, Kirk

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

For the Meyer Fund for Sustainable Development and the University of Oregon Department of Physics and Solar Radiation Monitoring Laboratory  

E-Print Network [OSTI]

and Solar Radiation Monitoring Laboratory Page C.1 6/20/2011 Appendix C: Vocabulary The following cell or module Global Irradiance (GHI) Total solar radiation on a horizontal surface Direct Normal

Oregon, University of

282

Study of Flow Regimes in Multiply-Fractured Horizontal Wells in Tight Gas and Shale Gas Reservoir Systems  

E-Print Network [OSTI]

Various analytical, semi-analytical, and empirical models have been proposed to characterize rate and pressure behavior as a function of time in tight/shale gas systems featuring a horizontal well with multiple hydraulic fractures. Despite a small...

Freeman, Craig M.

2010-07-14T23:59:59.000Z

283

Dynamics of a horizontal cylinder oscillating as a wave energy converter about an off-centred axis.   

E-Print Network [OSTI]

The hydrodynamic properties of a horizontal cylinder which is free to pitch about an off-centred axis are studied and used to derive the equations of motion of a wave energy converter which extracts energy from incoming ...

Lucas, Jorge

2011-11-22T23:59:59.000Z

284

Tangent length and sight distance effects on accident rates at horizontal curves on two-lane rural highways  

E-Print Network [OSTI]

This thesis documents an evaluation of the relationships between accident rates at horizontal curves and preceding tangent length and sight distance. Data collection and statistical methods used to evaluate this relationship are presented. A base...

Fink, Kenneth Lee

1993-01-01T23:59:59.000Z

285

The development of uranium foil farication technology utilizing twin roll method for Mo-99 irradiation target  

E-Print Network [OSTI]

MDS Nordion in Canada, occupying about 75% of global supply of Mo-99 isotope, has provided the irradiation target of Mo-99 using the rod-type UAl sub x alloys with HEU(High Enrichment Uranium). ANL (Argonne National Laboratory) through co-operation with BATAN in Indonesia, leading RERTR (Reduced Enrichment for Research and Test Reactors) program substantially for nuclear non-proliferation, has designed and fabricated the annular cylinder of uranium targets, and successfully performed irradiation test, in order to develop the fabrication technology of fission Mo-99 using LEU(Low Enrichment Uranium). As the uranium foils could be fabricated in laboratory scale, not in commercialized scale by hot rolling method due to significant problems in foil quality, productivity and economic efficiency, attention has shifted to the development of new technology. Under these circumstances, the invention of uranium foil fabrication technology utilizing twin-roll casting method in KAERI is found to be able to fabricate LEU or...

Kim, C K; Park, H D

2002-01-01T23:59:59.000Z

286

GLOBAL IMPACT FROM THE HEART  

E-Print Network [OSTI]

GLOBAL IMPACT FROM THE HEART OF NORTHERN IRELAND #12;A first-class student experience in world-CLASS 18 CONTACT 26 CONTENTS 3GLOBAL IMPACT FROM THE HEART OF NORTHERN IRELAND #12;Queen's is a powerhouse THE HEART OF NORTHERN IRELANDGLOBAL IMPACT FROM THE HEART OF NORTHERN IRELAND CHANCELLOR'S WELCOME

Paxton, Anthony T.

287

RENEWABLES 2005 GLOBAL STATUS REPORT  

E-Print Network [OSTI]

RENEWABLES 2005 GLOBAL STATUS REPORT Paper prepared for the REN21 Network by The Worldwatch Institute Lead Author: Eric Martinotwww.ren21.net #12;Renewable Energy Policy Network for the 21st Century REN21 is a global policy network aimed at providing a forum for international leadership on renewable

Kammen, Daniel M.

288

GLOBAL IMPACT FROM THE HEART  

E-Print Network [OSTI]

GLOBAL IMPACT FROM THE HEART OF NORTHERN IRELAND #12;#12;CHANCELLOR'S WELCOME 4 VICE: INNOVATIVE AND WORLD-CLASS 18 CONTACT 26 CONTENTS 3GLOBAL IMPACT FROM THE HEART OF NORTHERN IRELAND #12;Queen THE HEART OF NORTHERN IRELANDGLOBAL IMPACT FROM THE HEART OF NORTHERN IRELAND CHANCELLOR'S WELCOME

Müller, Jens-Dominik

289

GLOBAL WARMING THE GREENHOUSE EFFECT  

E-Print Network [OSTI]

GLOBAL WARMING THE GREENHOUSE EFFECT AND YOUR FAMILY'S CONTRIBUTION TO IT Stephen E. Schwartz September 22, 2004 http://www.ecd.bnl.gov/steve/schwartz.html #12;#12;THE GREENHOUSE EFFECT #12;GLOBAL does anything about it. ­ Mark Twain­ Mark Twain Now with the greenhouse effect, we ARE doing something

Schwartz, Stephen E.

290

Dependence of maximum realizable convective energy on horizontal scale in a one-dimensional entraining jet model  

E-Print Network [OSTI]

DEPENDENCE OF MAXIMUM REALIZABLE CONVECTIVE ENERGY ON HORIZONTAL SCALE IN A ONE ? DIMENSIONAL ENTRAINING JET MODEL A Thesis by DAVID BILLINGS WOLFF Submitted to the Graduate College of Twas A&M University in partial fulfillment... on Horizontal Scale in a One ? Dimensional Entraining Jet Model. (May 1988) David Billings Wolff, B. S. , Texas AkM University Chairman of Advisory Committe: Phanindramohan Das A one dimensional numerical model of convective clouds was implemented in which...

Wolff, David Billings

1988-01-01T23:59:59.000Z

291

Comparison of Deuterium Retention for Ion-irradiated and Neutron-irradiated Tungsten  

SciTech Connect (OSTI)

The behavior of D retention for Fe{sup 2+}-irradiated tungsten with a damage of 0.025-3 dpa was compared with that for neutron-irradiated tungsten with 0.025 dpa. The D{sub 2} thermal desorption spectroscopy (TDS) spectra for Fe{sup 2+}-irradiated tungsten consisted of two desorption stages at 450 and 550 K, while that for neutron-irradiated tungsten was composed of three stages and an addition desorption stage was found at 750 K. The desorption rate of the major desorption stage at 550K increased as the displacement damage increased due to Fe{sup 2+} irradiation increasing. In addition, the first desorption stage at 450K was found only for damaged samples. Therefore, the second stage would be based on intrinsic defects or vacancy produced by Fe{sup 2+} irradiation, and the first stage should be the accumulation of D in mono-vacancy and the activation energy would be relatively reduced, where the dislocation loop and vacancy is produced. The third one was found only for neutron irradiation, showing the D trapping by a void or vacancy cluster, and the diffusion effect is also contributed to by the high full-width at half-maximum of the TDS spectrum. Therefore, it can be said that the D{sub 2} TDS spectra for Fe{sup 2+}-irradiated tungsten cannot represent that for the neutron-irradiated one, indicating that the deuterium trapping and desorption mechanism for neutron-irradiated tungsten is different from that for the ion-irradiated one.

Yasuhisa Oya; Masashi Shimada; Makoto Kobayashi; Takuji Oda; Masanori Hara; Hideo Watanabe; Yuji Hatano; Pattrick Calderoni; Kenji Okuno

2011-12-01T23:59:59.000Z

292

Effects of aerosol and horizontal inhomogeneity on the broadband albedo of marine stratus: Numerical simulations  

SciTech Connect (OSTI)

Recent estimates of the effect of increasing of anthropogenic sulfate aerosol on the radiative forcing of the atmosphere have indicated that its impact may be comparable in magnitude to the effect from increases in CO{sub 2}. Much of this impact is expected from the effects of the aerosol on cloud microphysics and the subsequent impact on cloud albedo. A solar broadband version of a 2D radiative transfer model was used to quantify the impact of enhanced aerosol concentrations and horizontal inhomogeneity on the solar broadband albedo of marine stratus. The results of the radiative transfer calculations indicated that in unbroken marine stratus clouds the net horizontal transport of photons over a domain of a few kilometers was nearly zero, and the domain-average broadband albedo computed in a 2D cross section was nearly identical to the domain average calculated from a series of independent pixel approximation (IPA) calculations of the same cross section. However, the horizontal inhomogeneity does affect the cloud albedo compared to plane-parallel approximation (PPA) computations due to the nonlinear relationship between albedo and optical depth. The reduction in cloud albedo could be related to the variability of the distribution of log (cloud optical depth). These results extend the finding of Cahalan et al. to broadband solar albedos in a more realistic cloud model and suggest that accurate computation of domain-averaged broadband albedos in unbroken (or nearly unbroken) marine stratus can be made using IPA calculations with 1D radiative transfer models. Computations of the mean albedo over portions of the 3D RAMS domain show the relative increase in cloud albedo due to a 67% increase in the boundary-layer average CCN concentration was between 6% and 9%. The effects of cloud inhomogeneity on the broadband albedo as measured from the PPA bias ranged from 3% to 5%. 25 refs., 8 figs., 4 tabs.

Duda, D.P.; Stephens, G.L.; Stevens, B.; Cotton, W.R. [Colorado State Univ., Fort Collins, CO (United States)] [Colorado State Univ., Fort Collins, CO (United States)

1996-12-15T23:59:59.000Z

293

Applicability of petroleum horizontal drilling technology to hazardous waste site characterization and remediation  

SciTech Connect (OSTI)

Horizontal wells have the potential to become an important tool for use in characterization, remediation and monitoring operations at hazardous waste disposal, chemical manufacturing, refining and other sites where subsurface pollution may develop from operations or spills. Subsurface pollution of groundwater aquifers can occur at these sites by leakage of surface disposal ponds, surface storage tanks, underground storage tanks (UST), subsurface pipelines or leakage from surface operations. Characterization and remediation of aquifers at or near these sites requires drilling operations that are typically shallow, less than 500-feet in depth. Due to the shallow nature of polluted aquifers, waste site subsurface geologic formations frequently consist of unconsolidated materials. Fractured, jointed and/or layered high compressive strength formations or compacted caliche type formations can also be encountered. Some formations are unsaturated and have pore spaces that are only partially filled with water. Completely saturated underpressured aquifers may be encountered in areas where the static ground water levels are well below the ground surface. Each of these subsurface conditions can complicate the drilling and completion of wells needed for monitoring, characterization and remediation activities. This report describes some of the equipment that is available from petroleum drilling operations that has direct application to groundwater characterization and remediation activities. A brief discussion of petroleum directional and horizontal well drilling methodologies is given to allow the reader to gain an understanding of the equipment needed to drill and complete horizontal wells. Equipment used in river crossing drilling technology is also discussed. The final portion of this report is a description of the drilling equipment available and how it can be applied to groundwater characterization and remediation activities.

Goranson, C.

1992-09-01T23:59:59.000Z

294

Case Study of the Application of a Modified Method to Measure Global Solar Irradiance  

SciTech Connect (OSTI)

Case study that examines the application of a pyranometer responsivity function to data from 23 measurement stations in the Southern Great Plains.

Rael, F. P.

2006-02-01T23:59:59.000Z

295

COMPARISON OF METHODOLOGIES TO ESTIMATE DIRECT NORMAL IRRADIATION FROM DAILY VALUES OF GLOBAL  

E-Print Network [OSTI]

. The reason is that a dual automatic tracker was installed by the end of 1999, providing better DNI 2-axis tracker. Measurements have been recorded every 5 seconds, but for the purpose of this work Sevilla (Spain). Phone: (+34) 954487233. Fax: (+34) 954 487233. E-mail: saramt@esi.us.es 2 Solar Thermal

Paris-Sud XI, Université de

296

An adaptive method to derive direct irradiance from global , P. Blanc2  

E-Print Network [OSTI]

for Concentrated Solar Technology (CST) such as solar energy conversion systems: parabolic through, solar towers.oumbe-ndeffotsing@total.com 1 Total Gas & Power, R&D ­ Concentrated Solar Technologies, France 2 MINES ParisTech ­ Center for Energy and Processes, France Abstract Observations and estimations of solar radiation at ground level

Boyer, Edmond

297

The experimental and theoretical investigaton of a horizontal-axis wind turbine  

E-Print Network [OSTI]

. Design details of the wind turbine are discussed by the sections shown in the figure . Main Su ort Assembl The 3/4 in. diameter rotor shaft is supported at each end by roller bearings. Each bearing is clamped between two aluminum blocks. A flange...THE EXPERIMENTAL AND THEORETICAL INVESTIGATION OF A HORIZONTAL-AXIS WIND TURBINE A Thesis by ROBERT TERRANCE MILBURN Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER...

Milburn, Robert Terrance

1977-01-01T23:59:59.000Z

298

Vertical and horizontal test results of 3.9-GHz accelerating cavities at FNAL  

SciTech Connect (OSTI)

The 3rd harmonic 3.9GHz accelerating cavity was proposed to improve the beam performance of the VUV FEL, FLASH. In the frame of a collaborative agreement, Fermilab will provide DESY with a cryomodule containing a string of four cavities. Seven 9-cell Nb cavities were tested and six of them did reach accelerating gradient up to 24 MV/m almost twice more than design value of 14 MV/m. Two of these cavities are with new HOM couplers with improved design. In this paper we present all results of the vertical and horizontal tests.

Khabiboulline, T.; Edwards, H.; Foley, M.; Harms, E.; Hocker, James Andrew; Mitchell, D.; Rowe, A.; Solyak, N.; /Fermilab

2008-06-01T23:59:59.000Z

299

Dynamics of a drop trapped inside a horizontal circular hydraulic jump  

E-Print Network [OSTI]

A drop of moderate size deposited inside a horizontal circular hydraulic jump of the same liquid remains trapped at the shock front and does not coalesce. In this situation the drop is moving along the jump and one observes two different motions: a periodic one (it orbitates at constant speed) and an irregular one involving reversals of the orbital motion. Modeling the drop as a rigid sphere exchanging friction with liquid across a thin film of air, we recover the orbital motion and the internal rotation of the drop. This internal rotation is experimentally observed.

Duchesne, Alexis; Lebon, Luc; Pirat, Christophe; Limat, Laurent

2013-01-01T23:59:59.000Z

300

Orbits and reversals of a drop rolling inside a horizontal circular hydraulic jump  

E-Print Network [OSTI]

We explore the complex dynamics of a non-coalescing drop of moderate size inside a circular hydraulic jump of the same liquid formed on a horizontal disk. In this situation the drop is moving along the jump and one observes two different motions: a periodic one (it orbitates at constant speed) and an irregular one involving reversals of the orbital motion. Modeling the drop as a rigid sphere exchanging friction with liquid across a thin film of air, we recover the orbital motion and the internal rotation of the drop. This internal rotation is experimentally observed.

Alexis Duchesne; Clément Savaro; Luc Lebon; Christophe Pirat; Laurent Limat

2013-02-14T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Large Angle MSW Solution in Grand Unified Theories with SU(3) X U(1) Horizontal Symmetry  

E-Print Network [OSTI]

We construct a model with a SU(3) X U(1) horizontal symmetry in the context of Grand Unified Theories. In our models, the bi-maximal lepton mixing and suitable neutrino masses for the large angle MSW solution are obtained without any fine-tuning due to the spontaneously broken SU(3)_H symmetry. The three generations of quarks and leptons are unified as members of the SU(3)_H fundamental representation, and the U(1)_H charge gives the origin of the fermion mass hierarchy and mixing angles. We present two explicit examples of SU(5)_GUT and SO(10)_GUT models, in which the Yukawa structures are given successfully.

Ryuichiro Kitano; Yukihiro Mimura

2000-09-13T23:59:59.000Z

302

Globular clusters with the extended horizontal-branch as remaining cores of galaxy building blocks  

E-Print Network [OSTI]

The relics of building blocks that made stellar halo and bulge are yet to be discovered unless they were completely disrupted throughout the history of the Galaxy. Here we suggest that about 25% of the Milky Way globular clusters have characteristics of the remaining cores of these early building blocks rather than genuine star clusters. They are clearly distinct from other normal globular clusters in the presence of extended horizontal-branch and multiple stellar populations, in mass (brightness), and most importantly in orbital kinematics. Based on this result, a three-stage formation picture of the Milky Way is suggested, which includes early mergers, collapse, and later accretion.

Young-Wook Lee; Hansung B. Gim; Chul Chung

2007-07-11T23:59:59.000Z

303

Measurements of SCRF cavity dynamic heat load in horizontal test system  

SciTech Connect (OSTI)

The Horizontal Test System (HTS) at Fermilab is currently testing fully assembled, dressed superconducting radio frequency (SCRF) cavities. These cavities are cooled in a bath of superfluid helium at 1.8K. Dissipated RF power from the cavities is a dynamic heat load on the cryogenic system. The magnitude of heat flux from these cavities into the helium is also an important variable for understanding cavity performance. Methods and hardware used to measure this dynamic heat load are presented. Results are presented from several cavity tests and testing accuracy is discussed.

DeGraff, B.D.; Bossert, R.J.; Pei, L.; Soyars, W.M.; /Fermilab

2009-11-01T23:59:59.000Z

304

Security camera resolution measurements: Horizontal TV lines versus modulation transfer function measurements.  

SciTech Connect (OSTI)

The horizontal television lines (HTVL) metric has been the primary quantity used by division 6000 related to camera resolution for high consequence security systems. This document shows HTVL measurements are fundamen- tally insufficient as a metric to determine camera resolution, and propose a quantitative, standards based methodology by measuring the camera system modulation transfer function (MTF), the most common and accepted metric of res- olution in the optical science community. Because HTVL calculations are easily misinterpreted or poorly defined, we present several scenarios in which HTVL is frequently reported, and discuss their problems. The MTF metric is discussed, and scenarios are presented with calculations showing the application of such a metric.

Birch, Gabriel Carisle; Griffin, John Clark

2015-01-01T23:59:59.000Z

305

Dynamics of a Bose-Einstein condensate in a horizontally vibrating shallow optical lattice  

SciTech Connect (OSTI)

We consider a solitonic solution of the self-attractive Bose-Einstein condensate in a one-dimensional external potential of a shallow optical lattice with large periodicity when the lattice is horizontally shaken. We investigate the dynamics of the bright soliton through the properties of the fixed points. The special type of bifurcation results in a simple criterion for the stability of the fixed points depending only on the amplitude of the shaking lattice. Because of the similarity of the equations with those of an ac-driven Josephson junction, some results may find applications in other branches of physics.

Valizadeh, A.; Jahanbani, Kh.; Kolahchi, M. R. [Institute for Advanced Studies in Basic Sciences, P.O. Box 45195-1159, Zanjan (Iran, Islamic Republic of)

2010-02-15T23:59:59.000Z

306

Resisting globalization- ATTAC in France: local discourses, global terrain  

E-Print Network [OSTI]

The debate over the "globalization" process has been influenced by the emergence of social movements who deplore this process. This research focuses on the French social movement ATTAC (Action for a Tobin Tax for the Aid of Citizens...

Leonard, Marie des Neiges

2007-04-25T23:59:59.000Z

307

E-Print Network 3.0 - additive irradiation procedures Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

irradiation procedures Search Powered by Explorit Topic List Advanced Search Sample search results for: additive irradiation procedures Page: << < 1 2 3 4 5 > >> 1 IRRADIANCE MAPS...

308

Specific Examples of Global Activities Environmental assessment in Azerbaijan  

E-Print Network [OSTI]

, global warming, and global entrepreneurship. Discovery Park works syner- gistically with the Office competitiveness, global energy security, global warming, and global entrepreneurship. Discovery Park worksSpecific Examples of Global Activities · Environmental assessment in Azerbaijan · Study abroad

309

The China-in-Global Energy Model  

E-Print Network [OSTI]

The China-in-Global Energy Model (C-GEM) is a global Computable General Equilibrium (CGE) model that captures the interaction of production, consumption and trade among multiple global regions and sectors – including five ...

Qi, T.

310

Performance of hydraulic fracturing and matrix acidizing in horizontal wellbores -- Offshore Qatar  

SciTech Connect (OSTI)

Considerable debate in the Middle East has centered upon what was previously felt to be two separate methods of enhancing revenues and daily production; hydraulic fracturing and horizontal drilling. In an effort to maximize return on investment, these two issues have been successfully combined in other areas of the world. In order to establish the suitability of this technology in this area, two horizontal wells with over 3,050m (10,000ft) of lateral section were drilled into the Cretaceous Kharaib formation, overlying the North Field, Offshore Qatar. A massive stimulation program was performed in order to evaluate the most feasible stimulation method from both a technical and economical perspective for further field development considerations.Three propped hydraulic fracturing treatments were performed using 183, 500kg (403, 700lb) of 20/40 mesh sand, and seventeen acid matrix treatments placing over 3,217,250l (850,000gals) of HCL into the lateral sections of both wells. This paper describes the performance, operation and logistical support required to complete this offshore operation with join a minimal time frame. The use of a mobile offshore jack-up platform, whereby a land based fracturing spread was placed onto the deck of a converted drilling rig is described.

Edwards, M.G.R.; Pongratz, R.

1995-11-01T23:59:59.000Z

311

Horizontal Steam Generator Thermal-Hydraulics at Various Steady-State Power Levels  

SciTech Connect (OSTI)

Three-dimensional computer simulation and analyses of the horizontal steam generator thermal-hydraulics of the WWER 1000 nuclear power plant have been performed for 50% and 75% partial loads, 100% nominal load and 110% over-load. Presented results show water and steam mass flow rate vectors, steam void fraction spatial distribution, recirculation zones, swell level position, water mass inventory on the shell side, and other important thermal-hydraulic parameters. The simulations have been performed with the computer code 3D ANA, based on the 'two-fluid' model approach. Steam-water interface transport processes, as well as tube bundle flow resistance, energy transfer, and steam generation within tube bundles are modelled with {sup c}losure laws{sup .} Applied approach implies non-equilibrium thermal and flow conditions. The model is solved by the control volume procedure, which has been extended in order to take into account the 3D flow of liquid and gas phase. The methodology is validated by comparing numerical and experimental results of real steam generator operational conditions at various power levels of the WWER Novovoronezh, Unit 5. One-dimensional model of the horizontal steam generator has been built with the RELAP 5 standard code on the basis of the multidimensional two-phase flow structure obtained with the 3D ANA code. RELAP 5 and 3D ANA code results are compared, showing acceptable agreement. (authors)

Stevanovic, Vladimir D. [University of Belgrade, Kraljice Marije 16, 11000 Belgrade, Serbia and Montenegro (Yugoslavia); Stosic, Zoran V.; Kiera, Michael; Stoll, Uwe [Framatome ANP GmbH, P.O. Box 3220, 91050 Erlangen (Germany)

2002-07-01T23:59:59.000Z

312

Integrated approach towards the Application of Horizontal Wells to Improve Waterflooding Performance. Annual report  

SciTech Connect (OSTI)

This annual report describes the progress during the first year of the project on Integrated Approach Towards the Application of Horizontal Wells to Improve Waterflooding Performance. This project is funded under the Department of Energy`s Class I program which is targeted towards improving the reservoir performance of mature oil fields located in fluvial-dominated deltaic deposits. The project involves an integrated approach to characterize the reservoir followed by drilling of horizontal injection wells to improve production performance. The type of data the authors intend to integrate includes cross bore hole seismic surveys, geological interpretation based on logs and cores, and engineering information. This report covers the first phase of the project which includes a detailed reservoir description of the field based on the available information, followed by flow simulation of the Self Unit to compare the simulated result with the historical performance. Based on the simulated results, a vertical test well was drilled to validate this reservoir description. The well will also be used as a source well for a cross bore hole seismic survey. This report discusses the related geophysical, geological and engineering activities leading to the drilling of the vertical test well. The validation phase and the collection of the cross bore hole survey has just begun, and the results will be presented in the next annual report.

Kelkar, M.; Liner, C.; Kerr, D.

1994-06-01T23:59:59.000Z

313

Natural convection heat transfer for a staggered array of heated, horizontal cylinders within a rectangular enclosure  

SciTech Connect (OSTI)

This thesis presents the results of an experimental investigation of natural convection heat transfer in a staggered array of heated cylinders, oriented horizontally within a rectangular enclosure. The main purpose of this research was to extend the knowledge of heat transfer within enclosed bundles of spent nuclear fuel rods sealed within a shipping or storage container. This research extends Canaan`s investigation of an aligned array of heated cylinders that thermally simulated a boiling water reactor (BWR) spent fuel assembly sealed within a shipping or storage cask. The results are presented in terms of piecewise Nusselt-Rayleigh number correlations of the form Nu = C(Ra){sup n}, where C and n are constants. Correlations are presented both for individual rods within the array and for the array as a whole. The correlations are based only on the convective component of the heat transfer. The radiative component was calculated with a finite-element code that used measured surface temperatures, rod array geometry, and measured surface emissivities as inputs. The correlation results are compared to Canaan`s aligned array results and to other studies of natural convection in horizontal tube arrays.

Triplett, C.E.

1996-12-01T23:59:59.000Z

314

Natural convection in horizontal porous layers with localized heating from below  

SciTech Connect (OSTI)

Convective flow of fluid through saturated porous media heated from below is of considerable interest, and has been extensively studied. Most of these studies are concerned with either infinite horizontal porous layers or rectangular (or cylindrical) porous cavities with adiabatic vertical walls. A related problem of practical importance occurs when only a portion of the bottom surface is heated and the rest of it is either adiabatic or isothermally cooled. This situation is encountered in several geothermal areas which consists of troughs of volcanic debris contained by walls of nonfragmented ignimbrite. Thus, the model region considered is a locally heated long trough of isotropic porous medium confined by impermeable and insulating surroundings. Also, the recent motivation to study this problem has come from the efforts to identify a geologic repository for nuclear waste disposal. The purpose of the present work is to consider the effects of aspect ratio and Rayleigh number on free convection heat transfer from an isothermal heat source centrally located on the bottom surface of a horizontal porous cavity.

Prasad, V. (Columbia Univ., New York, NY (United States)); Kulacki, F.A. (Univ. of Delaware, Newark (United States))

1987-08-01T23:59:59.000Z

315

PARTNERSHIP PROFILE: THE GLOBAL FUND | 1 About the Global Fund to Fight AIDS,  

E-Print Network [OSTI]

grants worth a total of US$29 billion in more than 140 countries. The Global Fund provided 22% of allPARTNERSHIP PROFILE: THE GLOBAL FUND | 1 MARCH 2014 About the Global Fund to Fight AIDS, Tuberculosis and Malaria The Global Fund to Fight AIDS, Tuberculosis and Malaria (Global Fund) is a global

Klein, Ophir

316

Global energy demand to 2060  

SciTech Connect (OSTI)

The projection of global energy demand to the year 2060 is of particular interest because of its relevance to the current greenhouse concerns. The long-term growth of global energy demand in the time scale of climatic change has received relatively little attention in the public discussion of national policy alternatives. The sociological, political, and economic issues have rarely been mentioned in this context. This study emphasizes that the two major driving forces are global population growth and economic growth (gross national product per capita), as would be expected. The modest annual increases assumed in this study result in a year 2060 annual energy use of >4 times the total global current use (year 1986) if present trends continue, and >2 times with extreme efficiency improvements in energy use. Even assuming a zero per capita growth for energy and economics, the population increase by the year 2060 results in a 1.5 times increase in total annual energy use.

Starr, C. (Electric Power Research Institute, Palo Alto, CA (USA))

1989-01-01T23:59:59.000Z

317

Tropospheric chemistry: A global perspective  

E-Print Network [OSTI]

a global Openshaw, K. , Wood fuels the developing world, Newbetween 6 and 40% of wood fuel is converted to charcoalsimilar to that for wood fuel. The source for CO given in

Logan, Jennifer A; Prather, Michael J; Wofsy, Steven C; McElroy, Michael B

1981-01-01T23:59:59.000Z

318

Global Environment Facility Evaluation Office  

E-Print Network [OSTI]

Global Environment Facility Evaluation Office PROTECTED AREAS AND AVOIDED DEFORESTATION #12;Protected Areas and Avoided Deforestation: An Econometric Evaluation - i - TABLE OF CONTENTS 1................................................................................4 3.3 ESTIMATED EFFECTS OF PROTECTED AREAS ON DEFORESTATION

Pfaff, Alex

319

Global optimization in reduced space  

E-Print Network [OSTI]

Optimization is a key activity in any engineering discipline. Global optimization methods, in particular, strive to solve nonconvex problems, which often arise in chemical engineering, and deterministic algorithms such as ...

Wechsung, Achim

2014-01-01T23:59:59.000Z

320

Laboratory for Characterization of Irradiated Graphite  

SciTech Connect (OSTI)

The newly completed Idaho National Laboratory (INL) Carbon Characterization Laboratory (CCL) is located in Labs C19 and C20 of the Idaho National Laboratory Research Center (IRC). The CCL was established under the Next Generation Nuclear Plant (NGNP) Project to support graphite and ceramic composite research and development activities. The research is in support of the Advanced Graphite Creep (AGC) experiment — a major material irradiation experiment within the NGNP Graphite program. The CCL is designed to characterize and test low activated irradiated materials such as high purity graphite, carbon-carbon composites, and silicon-carbide composite materials. The laboratory is fully capable of characterizing material properties for both irradiated and nonirradiated materials.

Karen A. Moore

2010-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Irradiation creep of vanadium-base alloys.  

SciTech Connect (OSTI)

A study of irradiation creep in vanadium-base alloys is underway with experiments in the Advanced Test Reactor (ATR) and the High Flux Isotope Reactor (HFIR) in the US. Test specimens are thin-wall sealed tubes with internal pressure loading. The results from the initial ATR irradiation at low temperature (200-300 C) to a neutron damage level of 4.7 dpa show creep rates ranging from {approx}0 to 1.2 x 10{sup {minus}5}/dpa/MPa for a 500-kg heat of V-4Cr-4Ti alloy. These rates were generally lower than reported from a previous experiment in BR-10. Because both the attained neutron damage levels and the creep strains were low in the present study, however, these creep rates should be regarded as only preliminary. Substantially more testing is required before a data base on irradiation creep of vanadium alloys can be developed and used with confidence.

Tsai, H.; Matsui, H.; Billone, M. C.; Strain, R. V.; Smith, D. L.

1998-05-18T23:59:59.000Z

322

Irradiation effects on borosilicate waste glasses  

SciTech Connect (OSTI)

The effects of alpha decay on five borosilicate glasses containing simulated nuclear high-level waste oxides were studied. Irradiations carried out at room temperature were achieved by incorporating 1 to 8 wt % /sup 244/Cm/sub 2/O/sub 3/ in the glasses. Density changes and stored-energy build-up saturated at doses less than 2 x 10/sup 21/ alpha decays/kg. Damage manifested by stored energy was completely annealed at 633/sup 0/K. Positive and negative density changes were observed which never exceeded 1%. Irradiation had very little effect on mechanical strength or on chemical durability as measured by aqueous leach rates. Also, no effects were observed on the microstructure for vitreous waste glasses, although radiation-induced microcracking could be achieved on specimens that had been devitrified prior to irradiation.

Roberts, F.P.

1980-06-01T23:59:59.000Z

323

Heavy ion irradiation of crystalline water ice  

E-Print Network [OSTI]

Under cosmic irradiation, the interstellar water ice mantles evolve towards a compact amorphous state. Crystalline ice amorphisation was previously monitored mainly in the keV to hundreds of keV ion energies. We experimentally investigate heavy ion irradiation amorphisation of crystalline ice, at high energies closer to true cosmic rays, and explore the water-ice sputtering yield. We irradiated thin crystalline ice films with MeV to GeV swift ion beams, produced at the GANIL accelerator. The ice infrared spectral evolution as a function of fluence is monitored with in-situ infrared spectroscopy (induced amorphisation of the initial crystalline state into a compact amorphous phase). The crystalline ice amorphisation cross-section is measured in the high electronic stopping-power range for different temperatures. At large fluence, the ice sputtering is measured on the infrared spectra, and the fitted sputtering-yield dependence, combined with previous measurements, is quadratic over three decades of electronic ...

Dartois, E; Boduch, P; Brunetto, R; Chabot, M; Domaracka, A; Ding, J J; Kamalou, O; Lv, X Y; Rothard, H; da Silveira, E F; Thomas, J C

2015-01-01T23:59:59.000Z

324

Global existence for the primitive equations with small anisotropic viscosity  

E-Print Network [OSTI]

diffusivity, and the horizontal viscosity and horizontal thermal diffusivity of size where 0 and no vertical thermal diffusivity and we also suppose that the horizontal viscosity and thermal diffusivity go , Van-Sang Ngo R´esum´e: Dans cet article, nous consid´erons le syst`eme des ´equations prim- itives

Charve, Frédéric

325

Solar Irradiances Measured using SPN1 Radiometers: Uncertainties and Clues for Development  

SciTech Connect (OSTI)

The fast development of solar radiation and energy applications, such as photovoltaic and solar thermodynamic systems, has increased the need for solar radiation measurement and monitoring, not only for the global component but also the diffuse and direct. End users look for the best compromise between getting close to state-of-the-art measurements and keeping capital, maintenance and operating costs to a minimum. Among the existing commercial options, SPN1 is a relatively low cost solar radiometer that estimates global and diffuse solar irradiances from seven thermopile sensors under a shading mask and without moving parts. This work presents a comprehensive study of SPN1 accuracy and sources of uncertainty, which results from laboratory experiments, numerical modeling and comparison studies between measurements from this sensor and state-of-the art instruments for six diverse sites. Several clues are provided for improving the SPN1 accuracy and agreement with state-of-the-art measurements.

Badosa, Jordi; Wood, John; Blanc, Philippe; Long, Charles N.; Vuilleumier, Laurent; Demengel, Dominique; Haeffelin, Martial

2014-12-08T23:59:59.000Z

326

NERSC Calculations Provide Independent Confirmation of Global...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Calculations Provide Independent Confirmation of Global Land Warming Since 1901 NERSC Calculations Provide Independent Confirmation of Global Land Warming Since 1901 September 9,...

327

Heavy-Section Steel Irradiation Program  

SciTech Connect (OSTI)

Maintaining the integrity of the reactor pressure vessel (RPV) in a light-water-cooled nuclear power plant is crucial in preventing and controlling severe accidents that have the potential for major contamination release. Because the RPV is the only key safety-related component of the plant for which a redundant backup system does not exist, it is imperative to fully understand the degree of irradiation-induced degradation of the RPV's fracture resistance that occurs during service. For this reason, the Heavy-Section Steel Irradiation (HSSI) Program has been established.

Rosseel, T.M.

2000-04-01T23:59:59.000Z

328

Gamma irradiation of the prenatal mouse dentition  

E-Print Network [OSTI]

as the dental lamina to the stage of the deposition of enamel and dentin. The purpose of this study was to determine the effect of a continuous stress of gamma irradiation on the structure of the odontogenic cells, the relative size and rate of development... development. In 1927, Leist (9) made a study of the effect of X-rays on teeth, which was brought about by the following rase. A worker in a Roentgen tube factory was exposed daily to a considerable dose of X-irradiation. Sometime later he began to show...

Kerley, Michael Auston

1969-01-01T23:59:59.000Z

329

Effects of neutron flux and irradiation temperature on irradiation embrittlement of A533B steels  

SciTech Connect (OSTI)

Irradiation embrittlement of A533B steels with low copper contents were investigated from the point of dose rate and irradiation temperature effects. Change of neutron flux in the range from {minus}10{sup 12} to {minus}10{sup 13} n/cm{sup 2}/s (E > 1 MeV) did not have a significant effect on the embrittlement. Irradiation temperature change of 1 C resulted in the transition temperature shift ({Delta}T{sub 41J}) of about 1 C and yield stress change ({Delta}{sigma}{sub y}) of about 0.8 MPa. Factors that might affect the embrittlement of low copper steels are also discussed.

Suzuki, Masahide; Onizawa, Kunio; Kizaki, Minoru [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan)

1996-12-31T23:59:59.000Z

330

Fructolysis in the semen of continuously irradiated and non-irradiated goats  

E-Print Network [OSTI]

Abbott showed that the androgenic activity of the testis is far more resistant to x- ray irradiation than is the germinal epi- 1 thelium. When Abbott administered 5, 000 and 10, OOOR to rats, he found no decrease in the sex accessory organ weights nor.... Another point which supports the data that the damaged spermatogonia give rise to subnormal sperm is 23 the studies done with in vitro sperm that have been irradiated. Man 15 stated that irradiation of whole, fresh semen has little or no effect...

Ziller, Henry Hubert

1966-01-01T23:59:59.000Z

331

Understanding the Irradiation Behavior of Zirconium Carbide  

SciTech Connect (OSTI)

Zirconium carbide (ZrC) is being considered for utilization in high-temperature gas-cooled reactor fuels in deep-burn TRISO fuel. Zirconium carbide possesses a cubic B1-type crystal structure with a high melting point, exceptional hardness, and good thermal and electrical conductivities. The use of ZrC as part of the TRISO fuel requires a thorough understanding of its irradiation response. However, the radiation effects on ZrC are still poorly understood. The majority of the existing research is focused on the radiation damage phenomena at higher temperatures (>450{degree}C) where many fundamental aspects of defect production and kinetics cannot be easily distinguished. Little is known about basic defect formation, clustering, and evolution of ZrC under irradiation, although some atomistic simulation and phenomenological studies have been performed. Such detailed information is needed to construct a model describing the microstructural evolution in fast-neutron irradiated materials that will be of great technological importance for the development of ZrC- based fuel. The goal of the proposed project is to gain fundamental understanding of the radiation-induced defect formation in zirconium carbide and irradiation response (ZrC) by using a combination of state-of-the-art experimental methods and atomistic modeling. This project will combine (1) in situ ion irradiation at a specialized facility at a national laboratory, (2) controlled temperature proton irradiation on bulk samples, and (3) atomistic modeling to gain a fundamental understanding of defect formation in ZrC. The proposed project will cover the irradiation temperatures from cryogenic temperature to as high as 800{degree}C, and dose ranges from 0.1 to 100 dpa. The examination of this wide range of temperatures and doses allows us to obtain an experimental data set that can be effectively used to exercise and benchmark the computer calculations of defect properties. Combining the examination of radiation-induced microstructures mapped spatially and temporally, microstructural evolution during post-irradiation annealing, and atomistic modeling of defect formation and transport energetics will provide new, critical understanding about property changes in ZrC. The behavior of materials under irradiation is determined by the balance between damage production, defect clustering, and lattice response. In order to predict those effects at high temperatures so targeted testing can be expanded and extrapolated beyond the known database, it is necessary to determine the defect energetics and mobilities as these control damage accumulation and annealing. In particular, low-temperature irradiations are invaluable for determining the regions of defect mobility. Computer simulation techniques are particularly useful for identifying basic defect properties, especially if closely coupled with a well-constructed and complete experimental database. The close coupling of calculation and experiment in this project will provide mutual benchmarking and allow us to glean a deeper understanding of the irradiation response of ZrC, which can then be applied to the prediction of its behavior in reactor conditions.

Motta, Arthur; Sridharan, Kumar; Morgan, Dane; Szlufarska, Izabela

2013-10-11T23:59:59.000Z

332

Response of Strontium Titanate to Ion and Electron Irradiation...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Strontium Titanate to Ion and Electron Irradiation. Response of Strontium Titanate to Ion and Electron Irradiation. Abstract: Response of strontium titanate (SrTiO3) to ion and...

333

Irradiation Stability of Carbon Nanotubes and Related Materials  

E-Print Network [OSTI]

defect annealing at elevated irradiation temperatures, which delays the formation of amorphous regions. Investigation of nanotube stability after various processing techniques and irradiation indicated that radiation response of CNTs in a composite...

Aitkaliyeva, Assel 1985-

2012-09-28T23:59:59.000Z

334

E-Print Network 3.0 - accelerated hyperfractionated irradiation...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Group Collection: Physics 79 Irradiation of Nd-Fe-B Permanent Magnets with APS Bending Magnet X-rays and 60 Summary: of 260 Mrad was used to irradiate Nd-Fe-B sample magnets with...

335

Implementation Plan for the Irradiated Materials Characterization Laboratory (IMCL)  

SciTech Connect (OSTI)

This document contains details regarding the planned implementation of the Irradiated Materials Characterization Laboratory at the INL.

Not Listed

2013-04-01T23:59:59.000Z

336

Effects of hadron irradiation on scintillating fibers  

SciTech Connect (OSTI)

Trackers based on scintillating-fiber technology are being considered by the Solenoidal Detector Collaboration at SSC and the D[phi] collaboration at Fermilab. An important issue is the effect of the radiation existing in the detector cores on fiber properties. Most studies of radiation damage in scintillators have irradiated small bulk samples rather than fibers, and have used X-rays, [sup 60]Co gammas, or electron beams, often at accelerated rates. The authors have irradiated some 600 fibers in the Fermilab Tevatron C[phi] area, thereby obtaining a hadronic irradiation at realistic rates. Four-meter-long samples of ten Bicron polystyrene-based fiber types, maintained in air, dry nitrogen, argon, and vacuum atmospheres within stainless-steel tubes, were irradiated for seven weeks at various distances from the accelerator beam pipes. Maximum doses, measured by thermoluminescence detectors, were about 80 Krad. Fiber properties, particularly light yield and attenuation length, have been measured over a one-year period. A description of the work together with the results is presented. At the doses achieved, corresponding to a few years of actual fiber-tracking detector operation, little degradation is observed. In addition, recovery after several days' exposure to air has been noted. Properties of unirradiated samples kept in darkness show no changes after one year.

Atac, M. (Univ. of California, Los Angeles, CA (United States) Fermi National Accelerator Lab., Batavia, IL (United States)); Buchanan, C.; Chrisman, D.; Cline, D.; Kolonko, J.; Kubic, J.; Park, J. (Univ. of California, Los Angeles, CA (United States)); Baumbaugh, A.; Binkley, M.; Bross, A.D.; Finley, D.; Elias, J.; Foster, G.W.; Kephart, R.; Kephart, R.; Kim, C.; Park, H.; Pla-Dalmau, A.; Rivetta, C.; Tkaczyk, S.; Wagner, R. (Fermi National Accelerator Lab., Batavia, IL (United States)); Chung, M.; Goldberg, H.; Jeskik, R.; Margulies, S.; Mendez, H.; Solomon, J.; Vaca, F. (Univ. of Illinois, Chicago, IL (United States)); Kelley, C. (Massachusetts College of Pharmacy and Allied Health Sciences, Boston, MA (United States)); Baumbaugh, B.; Bishop, J.; Biswas, N.; Cason, N.; Jacques, J.; Kehoe, R.; Kelly, M.; Kenney, V.; LoSecco, J.; Ruchti, R.; Shephard, W.; Warchol, J.; Wayne, M.; Marchant, J.; Mountain, R.J. (Univ. of Notre Dame, IN (United States)); Davis, D.; Vandergriff, D. (O

1993-08-01T23:59:59.000Z

337

SIPS: Solar Irradiance Prediction System Stefan Achleitner  

E-Print Network [OSTI]

-scaling capacities of renewable energy sources such as wind and solar. However, variability and uncertainty in powerSIPS: Solar Irradiance Prediction System Stefan Achleitner Computer Science and Engineering Liu and Alberto E. Cerpa Electrical Engineering and Computer Science University of California, Merced

Cerpa, Alberto E.

338

Continuous wave laser irradiation of explosives  

SciTech Connect (OSTI)

Quantitative measurements of the levels of continuous wave (CW) laser light that can be safely applied to bare explosives during contact operations were obtained at 532 nm, 785 nm, and 1550 nm wavelengths. A thermal camera was used to record the temperature of explosive pressed pellets and single crystals while they were irradiated using a measured laser power and laser spot size. A visible light image of the sample surface was obtained before and after the laser irradiation. Laser irradiation thresholds were obtained for the onset of any visible change to the explosive sample and for the onset of any visible chemical reaction. Deflagration to detonation transitions were not observed using any of these CW laser wavelengths on single crystals or pressed pellets in the unconfined geometry tested. Except for the photochemistry of DAAF, TATB and PBX 9502, all reactions appeared to be thermal using a 532 nm wavelength laser. For a 1550 nm wavelength laser, no photochemistry was evident, but the laser power thresholds for thermal damage in some of the materials were significantly lower than for the 532 nm laser wavelength. No reactions were observed in any of the studied explosives using the available 300 mW laser at 785 nm wavelength. Tables of laser irradiance damage and reaction thresholds are presented for pressed pellets of PBX9501, PBX9502, Composition B, HMX, TATB, RDX, DAAF, PETN, and TNT and single crystals of RDX, HMX, and PETN for each of the laser wavelengths.

McGrane, Shawn D.; Moore, David S.

2010-12-01T23:59:59.000Z

339

The Sun and Climate Solar Irradiance  

E-Print Network [OSTI]

The Sun and Climate #12;Solar Irradiance The Solar Constant f = 1.4 x 106 erg/cm2/s. Over is higher when the Sun is more magnetically active. ·The Sun was magnetically active, and the climate the Sun Drive Climate? #12;The Temperature's Rising #12;Sunspots and CO2 What is Cause and What is Effect

Walter, Frederick M.

340

Total Solar Irradiance Satellite Composites and their  

E-Print Network [OSTI]

Chapter 12 Total Solar Irradiance Satellite Composites and their Phenomenological Effect on Climate. Phenomenological solar signature on climate 310 9. Conclusion 312 1. INTRODUCTION A contiguoustotal solar from each other, in particular about whether the TSI minimum during solar Cycles 22e23 (1995

Scafetta, Nicola

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Development of general inflow performance relationships (IPR`s) for slanted and horizontal wells producing heterogeneous solution-gas drive reservoirs  

SciTech Connect (OSTI)

Since 1968, the Vogel equation has been used extensively and successfully for analyzing the inflow performance relationship (IPR) of flowing vertical wells producing by solution-gas drive. Oil well productivity can be rapidly estimated by using the Vogel IPR curve and well outflow performance. With recent interests on horizontal well technology, several empirical IPRs for solution-gas drive horizontal and slanted wells have been developed under homogeneous reservoir conditions. This report presents the development of IPRs for horizontal and slanted wells by using a special vertical/horizontal/slanted well reservoir simulator under six different reservoir and well parameters: ratio of vertical to horizontal permeability, wellbore eccentricity, stratification, perforated length, formation thickness, and heterogeneous permeability. The pressure and gas saturation distributions around the wellbore are examined. The fundamental physical behavior of inflow performance for horizontal wells is described.

Cheng, A.M.

1992-04-01T23:59:59.000Z

342

Global Cooling: Effect of Urban Albedo on Global Temperature  

SciTech Connect (OSTI)

In many urban areas, pavements and roofs constitute over 60% of urban surfaces (roof 20-25%, pavements about 40%). The roof and the pavement albedo can be increased by about 0.25 and 0.10, respectively, resulting in a net albedo increase for urban areas of about 0.1. Many studies have demonstrated building cooling-energy savings in excess of 20% upon raising roof reflectivity from an existing 10-20% to about 60%. We estimate U.S. potential savings in excess of $1 billion (B) per year in net annual energy bills. Increasing albedo of urban surfaces can reduce the summertime urban temperature and improve the urban air quality. Increasing the urban albedo has the added benefit of reflecting more of the incoming global solar radiation and countering the effect of global warming. We estimate that increasing albedo of urban areas by 0.1 results in an increase of 3 x 10{sup -4} in Earth albedo. Using a simple global model, the change in air temperature in lowest 1.8 km of the atmosphere is estimated at 0.01K. Modelers predict a warming of about 3K in the next 60 years (0.05K/year). Change of 0.1 in urban albedo will result in 0.01K global cooling, a delay of {approx}0.2 years in global warming. This 0.2 years delay in global warming is equivalent to 10 Gt reduction in CO2 emissions.

Akbari, Hashem; Menon, Surabi; Rosenfeld, Arthur

2007-05-22T23:59:59.000Z

343

Total Solar Irradiance Variability and the Solar Activity Cycle  

E-Print Network [OSTI]

It is suggested that the solar variability is due to the perturbed nature of the solar core and this variability is provided by the variability of the solar neutrino flux from the solar neutrino detectors i.e., Homestake, Superkamiokande, SAGE and GALLEX-GNO. The solar neutrino flux in the standard solar model (SSM) was calculated on the assumption of L_nu (neutrino luminosity) = L_gamma (optical luminosity) which implies that if there is a change in optical luminosity then solar neutrino flux data will also be changed. An internal dynamo due to the cyclic variation of nuclear energy generation inside the core of the sun is responsible for the solar activity cycle was suggested and thus the internal magnetic field is also variable. Again the changes in the nuclear energy generation induce structural changes that result in variations of the global solar parameters i.e., luminosity, radius and temperatures etc. From the analysis of total solar irradiance (TSI) data during the year from 1970 to 2003 we have found five phases within the solar activity cycle. The first phase (I) starts before two years from the sunspot minimum. The second phase (II) starts at the time of sunspot minimum and phase (III) starts before 2/3 years from sunspot maximum whereas phase (IV) starts at sunspot maximum and fifth phase (V) starts at after 2-3 years from sunspot maximum.

Probhas Raychaudhuri

2006-05-06T23:59:59.000Z

344

Irradiation Embritlement in Alloy HT-­9  

SciTech Connect (OSTI)

HT-9 steel is a candidate structural and cladding material for high temperature lead-bismuth cooled fast reactors. In typical advanced fast reactor designs fuel elements will be irradiated for an extended period of time, reaching up to 5-7 years. Significant displacement damage accumulation in the steel is expected (> 200 dpa) when exposed to dpa-rates of 20-30 dpa{sub Fe}/y and high fast flux (E > 0.1 MeV) {approx}4 x 10{sup 15} n/cm{sup 2}s. Core temperatures could reach 400-560 C, with coolant temperatures at the inlet as low as 250 C, depending on the reactor design. Mechanical behavior in the presence of an intense fast flux and high dose is a concern. In particular, low temperature operation could be limited by irradiation embrittlement. Creep and corrosion effects in liquid metal coolants could set a limit to the upper operating temperature. In this report, we focus on the low temperature operating window limit and describe HT-9 embrittlement experimental findings reported in the literature that could provide supporting information to facilitate the consideration of a Code Case on irradiation effects for this class of steels in fast reactor environments. HT-9 has an extensive database available on irradiation performance, which makes it the best choice as a possible near-term candidate for clad, and ducts in future fast reactors. Still, as it is shown in this report, embrittlement data for very low irradiation temperatures (< 200 C) and very high radiation exposure (> 150 dpa) is scarce. Experimental findings indicate a saturation of DBTT shifts as a function of dose, which could allow for long lifetime cladding operation. However, a strong increase in DBTT shift with decreasing irradiation temperature could compromise operation at low service temperatures. Development of a deep understanding of the physics involved in the radiation damage mechanisms, together with multiscale computer simulation models of irradiation embrittlement will provide the basis to derive trendlines and quantitative engineering predictions.

Serrano De Caro, Magdalena [Los Alamos National Laboratory

2012-08-27T23:59:59.000Z

345

Response of neutron-irradiated RPV steels to thermal annealing  

SciTech Connect (OSTI)

One of the options to mitigate the effects of irradiation on reactor pressure vessels (RPVs) is to thermally anneal them to restore the fracture toughness properties that have been degraded by neutron irradiation. This paper summarizes experimental results of work performed at the Oak Ridge National Laboratory (ORNL) to study the annealing response of several irradiated RPV steels.

Iskander, S.K.; Sokolov, M.A.; Nanstad, R.K.

1997-03-01T23:59:59.000Z

346

Total solar irradiance during the Holocene F. Steinhilber,1  

E-Print Network [OSTI]

Total solar irradiance during the Holocene F. Steinhilber,1 J. Beer,1 and C. Fro¨hlich2 Received 20 solar irradiance covering 9300 years is presented, which covers almost the entire Holocene. This reconstruction is based on a recently observationally derived relationship between total solar irradiance

Wehrli, Bernhard

347

The determination of stochastic loads on horizontal axis wind turbine blades  

SciTech Connect (OSTI)

The FAST Code which is capable of determining structural loads of a flexible, teetering, horizontal axis wind turbine is described and comparisons of calculated loads with test data are given at two wind speeds for the ESI-80. The FAST Code models a two-bladed HAWT with degrees-of-freedom for blade bending, teeter, drive train flexibility, yaw, and windwise and crosswind tower motion. The code allows blade dimensions, stiffnesses, and weights to differ and the code models tower shadow, wind shear, and turbulence. Additionally, dynamic stall is included as are delta-3 and an underslung rotor. Load comparisons are made with ESI-80 test data in the form of power spectral density, rainflow counting occurrence histograms, and azimuth averaged bin plots. It is concluded that agreement between the FAST Code and test results is good.

Freeman, L.N.; Wilson, R.E. [Oregon State Univ., Corvallis, OR (United States). Dept. of Mechanical Engineering

1998-05-01T23:59:59.000Z

348

Combined Experiment Phase 1. [Horizontal axis wind turbines: wind tunnel testing versus field testing  

SciTech Connect (OSTI)

How does wind tunnel airfoil data differ from the airfoil performance on an operating horizontal axis wind turbine (HAWT) The National Renewable Energy laboratory has been conducting a comprehensive test program focused on answering this question and understanding the basic fluid mechanics of rotating HAWT stall aerodynamics. The basic approach was to instrument a wind rotor, using an airfoil that was well documented by wind tunnel tests, and measure operating pressure distributions on the rotating blade. Based an the integrated values of the pressure data, airfoil performance coefficients were obtained, and comparisons were made between the rotating data and the wind tunnel data. Care was taken to the aerodynamic and geometric differences between the rotating and the wind tunnel models. This is the first of two reports describing the Combined Experiment Program and its results. This Phase I report covers background information such as test setup and instrumentation. It also includes wind tunnel test results and roughness testing.

Butterfield, C.P.; Musial, W.P.; Simms, D.A.

1992-10-01T23:59:59.000Z

349

Experimental on two sensors combination used in horizontal pipe gas-water two-phase flow  

SciTech Connect (OSTI)

Gas-water two phase flow phenomenon widely exists in production and living and the measurement of it is meaningful. A new type of long-waist cone flow sensor has been designed to measure two-phase mass flow rate. Six rings structure of conductance probe is used to measure volume fraction and axial velocity. The calibration of them have been made. Two sensors have been combined in horizontal pipeline experiment to measure two-phase flow mass flow rate. Several model of gas-water two-phase flow has been discussed. The calculation errors of total mass flow rate measurement is less than 5% based on the revised homogeneous flow model.

Wu, Hao; Dong, Feng [Tianjin Key Laboratory of Process Measurement and Control, School of Electrical Engineering and Automation, Tianjin University, Tianjin (China)

2014-04-11T23:59:59.000Z

350

Analysis of gallium arsenide deposition in a horizontal chemical vapor deposition reactor using massively parallel computations  

SciTech Connect (OSTI)

A numerical analysis of the deposition of gallium from trimethylgallium (TMG) and arsine in a horizontal CVD reactor with tilted susceptor and a three inch diameter rotating substrate is performed. The three-dimensional model includes complete coupling between fluid mechanics, heat transfer, and species transport, and is solved using an unstructured finite element discretization on a massively parallel computer. The effects of three operating parameters (the disk rotation rate, inlet TMG fraction, and inlet velocity) and two design parameters (the tilt angle of the reactor base and the reactor width) on the growth rate and uniformity are presented. The nonlinear dependence of the growth rate uniformity on the key operating parameters is discussed in detail. Efficient and robust algorithms for massively parallel reacting flow simulations, as incorporated into our analysis code MPSalsa, make detailed analysis of this complicated system feasible.

Salinger, A.G.; Shadid, J.N.; Hutchinson, S.A. [and others

1998-01-01T23:59:59.000Z

351

Apparatus and method for the horizontal, crucible-free growth of silicon sheet crystals  

DOE Patents [OSTI]

Apparatus is provided for continuously forming a silicon crystal sheet from a silicon rod in a non-crucible environment. The rod is rotated and fed toward an RF coil in an inert atmosphere so that the upper end of the rod becomes molten and the silicon sheet crystal is pulled therefrom substantially horizontally in a continuous strip. A shorting ring may be provided around the rod to limit the heating to the upper end only. Argon gas can be used to create the inert atmosphere within a suitable closed chamber. By use of this apparatus and method, a substantially defect-free silicon crystal sheet is formed which can be used for micro-circuitry chips or solar cells.

Ciszek, T.F.

1984-09-12T23:59:59.000Z

352

Method for forming an in situ oil shale retort with horizontal free faces  

DOE Patents [OSTI]

A method for forming a fragmented permeable mass of formation particles in an in situ oil shale retort is provided. A horizontally extending void is excavated in unfragmented formation containing oil shale and a zone of unfragmented formation is left adjacent the void. An array of explosive charges is formed in the zone of unfragmented formation. The array of explosive charges comprises rows of central explosive charges surrounded by a band of outer explosive charges which are adjacent side boundaries of the retort being formed. The powder factor of each outer explosive charge is made about equal to the powder factor of each central explosive charge. The explosive charges are detonated for explosively expanding the zone of unfragmented formation toward the void for forming the fragmented permeable mass of formation particles having a reasonably uniformly distributed void fraction in the in situ oil shale retort.

Ricketts, Thomas E. (Grand Junction, CO); Fernandes, Robert J. (Bakersfield, CA)

1983-01-01T23:59:59.000Z

353

Comparison of transient horizontal magnetic fields in a plage region and in the quiet Sun  

E-Print Network [OSTI]

Properties of transient horizontal magnetic fields (THMFs) in both plage and quiet Sun regions are obtained and compared. Spectro-polarimetric observations with the Solar Optical Telescope (SOT) on the Hinode satellite were carried out with a cadence of about 30 seconds for both plage and quiet regions located near disk center. We select THMFs that have net linear polarization (LP) higher than 0.22%, and an area larger than or equal to 3 pixels, and compare their occurrence rates and distribution of magnetic field azimuth. We obtain probability density functions (PDFs) of magnetic field strength and inclination for both regions.The occurrence rate in the plage region is the same as for the quiet Sun. The vertical magnetic flux in the plage region is ~8 times larger than in the quiet Sun. There is essentially no preferred orientation for the THMFs in either region. However, THMFs in the plage region with higher LP have a preferred direction consistent with that of the plage-region's large-scale vertical field pattern. PDFs show that there is no difference in the distribution of field strength of horizontal fields between the quiet Sun and the plage regions when we avoid the persistent large vertical flux concentrations for the plage region. The similarity of the PDFs and of the occurrence rates in plage and quiet regions suggests that a local dynamo process due to the granular motion may generate THMFs all over the sun. The preferred orientation for higher LP in the plage indicates that the THMFs are somewhat influenced by the larger-scale magnetic field pattern of the plage.

Ryohko Ishikawa; Saku Tsuneta

2008-12-09T23:59:59.000Z

354

Case Study #1 "The Global Warming Debate"  

E-Print Network [OSTI]

CHEM 001A Case Study #1 "The Global Warming Debate" Global warming is one of the most contentious issues of our time. There is an ongoing debate about whether global warming is caused by human activity.S., and because the scientific evidence used to determine if global warming is man-made is so difficult

Reed, Christopher A.

355

PRINT ONLY: GLOBAL WARMING Alexeev V. A.  

E-Print Network [OSTI]

PRINT ONLY: GLOBAL WARMING Alexeev V. A. Global Warming: 0.6°C or Less? [#1035] The peculiarities of global warming on the Earth during the last century are discussed. Lunar and Planetary Science XXXVIII (2007) full818.pdf #12;GLOBAL WARMING: 0.6 OR LESS? V.A.Alexeev; Vernadsky Institute of Geochemistry

Rathbun, Julie A.

356

Shrinking Global Population: A futuristic scenario  

E-Print Network [OSTI]

global population it will not be a game-changer. #12;Measures for changes in total births 1. TotalShrinking Global Population: A futuristic scenario or a current challenge. Hillel Bar of RSAI - Atlanta November 15, 2013 #12;The evolution of global population Year Global Population

Nagurney, Anna

357

A study of the appearance of tau neutrinos from a gamma ray burst by detecting their horizontal electromagnetic showers  

E-Print Network [OSTI]

We explore the possibilty of detecting horizontal electromagnetic showers of tau neutrinos from individual gamma ray bursts, in large scale detectors like HiRes and Telescope Array. We study the role of the parameters of a gamma ray burst in determining the expected number of tau events from that burst. The horizontal beam of tau leptons produce visible signals in the atmosphere. We find that there is a slim chance of observing tau lepton appearances from GRBs with Telescope Array. The number of signals is strongly dependent on the Lorentz factor $\\Gamma$, redshift $z$ of a GRB, energy emitted in muon neutrinos and antineutrinos $E_{\

Nayantara Gupta

2003-07-22T23:59:59.000Z

358

Sensitivity of ultrasonic nonlinearity to irradiated, annealed, and re-irradiated microstructure changes in RPV steels  

SciTech Connect (OSTI)

The planned life extension of nuclear reactors throughout the US and abroad will cause reactor vessel and internals materials to be exposed to more neutron irradiation than was originally intended. A nondestructive evaluation (NDE) method to monitor radiation damage would enable safe and cost-effective continued operation of nuclear reactors. Radiation damage in reactor pressure vessel (RPV) steels causes microstructural changes that leave the material in an embrittled state. Nonlinear ultrasound is an NDE technique quantified by the measurable acoustic nonlinearity parameter, which is sensitive to microstructural changes in metallic materials such as dislocations, precipitates and their combinations. Recent research has demonstrated the sensitivity of the acoustic nonlinearity parameter to increasing neutron fluence in representative RPV steels. The current work considers nonlinear ultrasonic experiments conducted on similar RPV steel samples that had a combination of irradiation, annealing, re-irradiation, and/or re-annealing to a total neutron fluence of 0.5 5 1019 n/cm2 (E > 1 MeV) at an irradiation temperature of 290 C. The acoustic nonlinearity parameter generally increased with increasing neutron fluence, and consistently decreased from the irradiated to the annealed state over different levels of neutron fluence. Results of the measured acoustic nonlinearity parameter are compared with those from previous measurements on other RPV steel samples. This comprehensive set of results illustrates the dependence of the measured acoustic nonlinearity parameter on neutron fluence, material composition, irradiation temperature and annealing.

Matlack, Katie [Georgia Institute of Technology, Atlanta] [Georgia Institute of Technology, Atlanta; Kim, J-Y. [Georgia Institute of Technology, Atlanta] [Georgia Institute of Technology, Atlanta; Wall, J.J. [Electric Power Research Institute (EPRI)] [Electric Power Research Institute (EPRI); Jacobs, L.J. [Georgia Institute of Technology, Atlanta] [Georgia Institute of Technology, Atlanta; Sokolov, Mikhail A [ORNL] [ORNL

2014-01-01T23:59:59.000Z

359

No Fracking Way! A Study on the Spatial Patterns of and Changes in Perception and Distance from a Michigan Horizontal Hydraulic Fracturing Site.  

E-Print Network [OSTI]

?? The research investigates whether Michigan residents' perception of risk from an oil and natural gas (ONG) well site that employs the use of horizontal… (more)

McEwen, Shannon

2014-01-01T23:59:59.000Z

360

Horizontal well construction/completion process in a Gulf of Mexico unconsolidated sand: development of baseline correlations for improved drill-in fluid cleanup practices.  

E-Print Network [OSTI]

??This thesis examines, in detail, the procedures and practices undertaken in the drilling and completion phases of a Gulf of Mexico horizontal well in an… (more)

Lacewell, Jason Lawrence

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Globalization: Ecological Consequences of Global-Scale Connectivity in People,  

E-Print Network [OSTI]

, 2005; Rial et al., 2004). For example, increasing atmospheric CO2 and other greenhouse gases of Agriculture ­ Agricultural Research Service, Las Cruces, New Mexico USA 1. Introduction Globalization). Movement of humans through improved transportation is leading to spread of pests and pathogens

362

Global change: Acronyms and abbreviations  

SciTech Connect (OSTI)

This list of acronyms and abbreviations is compiled to provide the user with a ready reference to dicipher the linguistic initialisms and abridgements for the study of global change. The terms included in this first edition were selected from a wide variety of sources: technical reports, policy documents, global change program announcements, newsletters, and other periodicals. The disciplinary interests covered by this document include agriculture, atmospheric science, ecology, environmental science, oceanography, policy science, and other fields. In addition to its availability in hard copy, the list of acronyms and abbreviations is available in DOS-formatted diskettes and through CDIAC`s anonymous File Transfer Protocol (FTP) area on the Internet.

Woodard, C.T. [Oak Ridge National Lab., TN (United States); Stoss, F.W. [Univ. of Tennessee, Knoxville, TN (United States). Energy, Environment and Resources Center

1995-05-01T23:59:59.000Z

363

Effects of stress on microstructural evolution during irradiation  

SciTech Connect (OSTI)

Many theories have been postulated to describe irradiation creep but few have been supported with microstructural evidence. The purpose of this paper is to review microstructural studies of the effects of stress during irradiation in order to assess the validity of the available irradiation creep theories. Microstructural studies based on high voltage electron, ion, proton and neutron irradiation will be described, with major emphasis placed on interpreting behavior demonstrated in austenitic steels. Special attention will be given to work on fast neutron irradiated Nimonic PE16, a precipitation strengthened superalloy.

Gelles, D.S. [Pacific Northwest Lab., Richland, VA (United States)

1992-12-31T23:59:59.000Z

364

Making Globalization Work for Sustainable Human Development The Global Programme Paradigm : A Synthesis Approach  

E-Print Network [OSTI]

the best practices and strategies to manage their integration into the global economy and therefore bringMaking Globalization Work for Sustainable Human Development The Global Programme Paradigm-UNDP Global Programme on Globalization, Liberalization and Sustainable Human Development* Gabriela Tejada

365

Conservation and Global Climate Change  

E-Print Network [OSTI]

V.6 Conservation and Global Climate Change Diane M. Debinski and Molly S. Cross OUTLINE 1. Introduction 2. How climate is changing 3. Environmental responses to climate change 4. Consequences of climate the coming decades will be preserving biodiversity in the face of climate change. It has become increasingly

Landweber, Laura

366

RENEWABLES 2007 GLOBAL STATUS REPORT  

E-Print Network [OSTI]

RENEWABLES 2007 GLOBAL STATUS REPORT www.ren21.net #12;Renewable Energy Policy Network for the 21st renewable energy. It provides a forum for leadership and exchange in international policy processes. It bolsters appropriate policies that increase the wise use of renewable energies in developing

Kammen, Daniel M.

367

GLOBAL WOOD SUPPLY Sten Nilsson  

E-Print Network [OSTI]

GLOBAL WOOD SUPPLY Sten Nilsson Biomass and Resource Efficiency: the need for a supply led approach to forest productivity European Parliament, Brussels, 10 November 2011 #12;MEGATREND WOOD SUPPLY ­ 2020 the trees on the right Source: JP Management Consulting (Asia-Pacific) Ltd., 2006 #12;BAMBOO FOREST Source

368

Workshop report Impact of Global  

E-Print Network [OSTI]

with an emphasis on low-to-middle-income countries 21­23 March 2012 Wellcome Trust, London #12;IMPACT OF GLOBALWorkshop report Impact of Global Environmental Change on Food/Nutrition and Water in Relation ENVIRONMENTAL CHANGE ON FOOD/NUTRITION AND WATER IN RELATION TO HUMAN HEALTH 21­23 March 2012 Wellcome Trust

Rambaut, Andrew

369

Cambio global y polucin atmosfrica  

E-Print Network [OSTI]

pollution and forest ecosystems Atmospheric pollution is referred as a component of global change. The role on the interaction between pollution and climate change. Key words: atmospheric pollution, acidic rain, anatomical anatómicos y fisiológicos, micorrizas, recursos ge- néticos, masas forestales españolas. Abstract Atmospheric

Espigares, Tíscar

370

7, 38373857, 2007 Global transports  

E-Print Network [OSTI]

and 180 are still transporting into soil and water. It is found that lighter PCBs have more long range international concern with identifying and managing environmentally persistent substances that are bothACPD 7, 3837­3857, 2007 Global transports and budgets of PCBs P. Huang et al. Title Page Abstract

Paris-Sud XI, Université de

371

Apparatus for efficient sidewall containment of molten metal with horizontal alternating magnetic fields utilizing a ferromagnetic dam  

DOE Patents [OSTI]

An apparatus is disclosed for casting sheets of metal from molten metal. The apparatus includes a containment structure having an open side, a horizontal alternating magnetic field generating structure and a ferromagnetic dam. The magnetic field and the ferromagnetic dam contain the molten metal from leaking out side portions of the open side of the containment structure. 25 figs.

Praeg, W.F.

1997-02-11T23:59:59.000Z

372

Gravity Waves in a Horizontal Shear Flow. Part II: Interaction between Gravity Waves and Potential Vorticity Perturbations  

E-Print Network [OSTI]

Gravity Waves in a Horizontal Shear Flow. Part II: Interaction between Gravity Waves and Potential perturbations and propagating internal gravity waves in a horizon- tally sheared zonal flow is investigated. In the strong stratification limit, an initial vorticity perturbation weakly excites two propagating gravity

Farrell, Brian F.

373

Economic Impact of Reservoir Properties, Horizontal Well Length and Orientation on Production from Shale Formations: Application to New  

E-Print Network [OSTI]

on Production from Shale Formations: Application to New Albany Shale A. Kalantari Dahaghi, S. D. Mohaghegh, West and the orientation of horizontal wells on gas production in New Albany Shale. The study was conducted using as fracture bedding of the New Albany Shale are modeled using information found in the literature and outcrops

Mohaghegh, Shahab

374

Apparatus for efficient sidewall containment of molten metal with horizontal alternating magnetic fields utilizing low reluctance rims  

DOE Patents [OSTI]

A method and apparatus for casting sheets of metal from molten metal. The apparatus includes a containment structure having an open side, a horizontal alternating magnetic field generating structure and rollers including low reluctance rim structures. The magnetic field and the rollers help contain the molten metal from leaking out of the containment structure.

Praeg, Walter F. (Palos Park, IL)

1999-01-01T23:59:59.000Z

375

Gravity Waves in a Horizontal Shear Flow. Part I: Growth Mechanisms in the Absence of Potential Vorticity Perturbations  

E-Print Network [OSTI]

Gravity Waves in a Horizontal Shear Flow. Part I: Growth Mechanisms in the Absence of Potential (Manuscript received 7 May 2007, in final form 17 July 2008) ABSTRACT Interaction of internal gravity waves of closed-form solutions. Localized wave packet trajectories are obtained, the energy growth mechanisms

Farrell, Brian F.

376

Horizontal coherence of low-frequency fixed-path sound in a continental shelf region with internal-wave activity  

E-Print Network [OSTI]

Horizontal coherence of low-frequency fixed-path sound in a continental shelf region with internal-wave) populated with tidally generated long- and short-wavelength internal waves. Sound paths are 19 km and explain sound field spatial and temporal variability under these conditions. The intermittent internal-wave

377

Statistical correlation between hourly and daily values of solar radiation on horizontal surface at sea level in the Italian climate  

E-Print Network [OSTI]

219- Statistical correlation between hourly and daily values of solar radiation on horizontal- nalières du rayonnement solaire. Abstract. 2014 The knowledge of hourly data of solar radiation is required data measured in Italian stations and propose a method to estimate hourly solar radiation

Boyer, Edmond

378

Analytical and semi-analytical solutions of horizontal well capture times under no-ow and constant-head boundaries  

E-Print Network [OSTI]

for oil and gas production in the past decade [15,21]. Extensive studies on pressure anal- ysis with surface restrictions (e.g., land®lls, lagoons, buildings, wetlands, lakes, utility lines, tanks), (2 organic contaminants. Fluid and gas ¯ows to a horizontal well or trench have been studied before. An early

Zhan, Hongbin

379

Simulation studies of a horizontal well producing from a thin oil-rim reservoir in the SSB1 field, Malaysia  

E-Print Network [OSTI]

Three-dimensional simulation studies have been carried out to investigate the performance of a horizontal well producing from a thin oil-rim reservoir, X3/X4 in the SSBI field, Malaysia. A heterogeneous model was used which honored the reservoir...

Abdul Hakim, Hazlan

1995-01-01T23:59:59.000Z

380

Impacts of Soil and Pipe Thermal Conductivity on Performance of Horizontal Pipe in a Ground-source Heat Pump  

E-Print Network [OSTI]

In this paper the composition and thermal property of soil are discussed. The main factors that impact the soil thermal conductivity and several commonly-used pipe materials are studied. A model of heat exchanger with horizontal pipes of ground-source...

Song, Y.; Yao, Y.; Na, W.

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

NREL Vehicle Testing and Integration Facility (VTIF): Rotating Shadowband Radiometer (RSR); Golden, Colorado (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

This measurement station at NREL's Vehicle Testing and Integration Facility (VTIF) monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location. The solar measurement instrumentation is also accompanied by meteorological monitoring equipment.

Lustbader, J.; Andreas, A.

382

Solar Radiation Monitoring Station (SoRMS): Humboldt State University, Arcata, California (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

A partnership with HSU and U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to collect solar data to support future solar power generation in the United States. The measurement station monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location.

Wilcox, S.; Andreas, A.

383

Materials Modification Under Ion Irradiation: JANNUS Project  

SciTech Connect (OSTI)

JANNUS (Joint Accelerators for Nano-Science and Nuclear Simulation) is a project designed to study the modification of materials using multiple ion beams and in-situ TEM observation. It will be a unique facility in Europe for the study of irradiation effects, the simulation of material damage due to irradiation and in particular of combined effects. The project is also intended to bring together experimental and modelling teams for a mutual fertilisation of their activities. It will also contribute to the teaching of particle-matter interactions and their applications. JANNUS will be composed of three accelerators with a common experimental chamber and of two accelerators coupled to a 200 kV TEM.

Serruys, Y.; Trocellier, P. [CEA-Saclay, DEN/DMN/SRMP, 91191 Gif-sur-Yvette Cedex (France); Ruault, M.-O.; Henry, S.; Kaietasov, O. [CSNSM, Bat. 104, Orsay Campus (France); Trouslard, Ph. [INSTN, CEA-Saclay, 91191 Gif-sur-Yvette Cedex (France)

2004-12-01T23:59:59.000Z

384

Neutron irradiation of beryllium: Recent Russian results  

SciTech Connect (OSTI)

Results on postirradiation tensile and compression testing, swelling and bubble growth during annealing for various grades of beryllium are presented. It is shown that swelling at temperatures above 550{degrees}C is sensitive to material condition and response is correlated with oxygen content. Swelling on the order of 15% can be expected at 700{degrees}C for doses on the order of 10{sup 22} n/cm{sup 2}. Bubble growth response depends on irradiation fluence.

Gelles, D.S. [Pacific Northwest Lab., Richland, VA (United States)

1992-12-31T23:59:59.000Z

385

ARM - Measurement - Shortwave broadband total net irradiance  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc Documentation RUC : XDCResearch Relatedcontent ARMnumberDoppler ARMdiffusedirectnet irradiance

386

ARM - Measurement - Shortwave narrowband direct downwelling irradiance  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc Documentation RUC : XDCResearch Relatedcontent ARMnumberDopplerdownwelling irradiance ARM Data

387

ARM - Measurement - Shortwave narrowband direct normal irradiance  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc Documentation RUC : XDCResearch Relatedcontent ARMnumberDopplerdownwelling irradiance ARM

388

``Climate Modelling & Global Change'' scientific report ``Climate Modelling & Global Change'' Team  

E-Print Network [OSTI]

``Climate Modelling & Global Change'' scientific report ``Climate Modelling & Global Change'' Team) : : : : : : : : : : : : : : : : : 6 2.2 Anthropogenic climate change studies: scenario experiments (96) : : : : : : : : : 7 2 following its creation, the ``Climate Modelling & Global Change'' team had to make its proofs in order

389

COLUMBIA ENGINEERING WINTER GLOBAL EDUCATIONAL EXPERIENCE: EXPLORING GLOBAL ENGINEERING WITH CITY UNIVERSITY OF HONG KONG  

E-Print Network [OSTI]

COLUMBIA ENGINEERING WINTER GLOBAL EDUCATIONAL EXPERIENCE: EXPLORING GLOBAL ENGINEERING WITH CITY UNIVERSITY OF HONG KONG JANUARY 7th ­ 15TH , 2012 Program Features The Winter Global Educational Experience is open to Columbia Engineering

Hone, James

390

Magnetic phase formation in irradiated austenitic alloys  

SciTech Connect (OSTI)

Austenitic alloys are often observed to develop magnetic properties during irradiation, possibly associated with radiation-induced acceleration of the ferrite phase. Some of the parametric sensitivities of this phenomenon have been addressed using a series of alloys irradiated in the BOR-60 reactor at 593K. The rate of development of magnetic phase appears to be sensitive to alloy composition. To the first order, the largest sensitivities to accelerate ferrite formation, as explored in this experiment, are associated with silicon, carbon and manganese and chromium. Si, C, and Mn are thought to influence diffusion rates of point defects while Cr plays a prominent role in defining the chromium equivalent and therefore the amount of ferrite at equilibrium. Pre-irradiation cold working was found to accelerate ferrite formation, but it can play many roles including an effect on diffusion, but on the basis of these results the dominant role or roles of cold-work cannot be identified. Based on the data available, ferrite formation is most probably associated with diffusion.

Gussev, Maxim N [ORNL] [ORNL; Busby, Jeremy T [ORNL] [ORNL; Tan, Lizhen [ORNL] [ORNL; Garner, Francis A. [Radiation Effects Consulting, Richland, WA] [Radiation Effects Consulting, Richland, WA

2014-01-01T23:59:59.000Z

391

Upgrade to the Birmingham Irradiation Facility  

E-Print Network [OSTI]

The Birmingham Irradiation Facility was developed in 2013 at the University of Birmingham using the Medical Physics MC40 cyclotron. It can achieve High Luminosity LHC (HL-LHC) fluences of 10^15 (1 MeV neutron equivalent (neq)) cm^-2 in 80 s with proton beam currents of 1 ?A and so can evaluate effectively the performance and durability of detector technologies and new components to be used for the HL-LHC. Irradiations of silicon sensors and passive materials can be carried out in a temperature controlled cold box which moves continuously through the homogenous beamspot. This movement is provided by a pre-configured XY-axis Cartesian robot scanning system. In 2014 the cooling system and cold box were upgraded from a recirculating glycol chiller system to a liquid nitrogen evaporative system. The new cooling system achieves a stable temperature of 50 1C in 30 min and aims to maintain sub-0 1C temperatures on the sensors during irradiations. This paper reviews the design, development, commissioning and perform...

Dervan, P; Hodgson, P; Marin- Reyes; Parker, K; Wilson, J; Baca, M

2015-01-01T23:59:59.000Z

392

Irradiation response and stability of nanoporous materials  

SciTech Connect (OSTI)

Nanoporous materials consist of a regular organic or inorganic framework supporting a regular, porous structure. Pores are by definition roughly in the nanometre range, that is between 0.2 nm and 100 nm. Nanoporous materials can be subdivided into 3 categories (IUPAC): (1) Microporous materials - 0.2-2 nm; (2) Mesoporous materials - 2-50 nm; and (3) Macroporous materials - 50-1000 nm. np-Au foams were successfully synthesized by de-alloying process. np-Au foams remain porous structure after Ne ion irradiation to 1 dpa. Stacking Fault Tetrahedra (SFTs) were observed in RT irradiated np-Au foams under the highest and intermediate fluxes, but not under the lowest flux. SFTs were not observed in LNT irradiated np-Au foams under all fluxes. The vacancy diffusivity in Au at RT is high enough so that the vacancies have enough time to agglomerate and then collapse to form SFTs. The high ion flux creates more damage per unit time; vacancies don't have enough time to diffuse or recombine. As a result, SFTs were formed at high ion fluxes.

Fu, Engang [Los Alamos National Laboratory; Wang, Yongqiang [Los Alamos National Laboratory; Serrano De Caro, Magdalena [Los Alamos National Laboratory; Caro, Jose A. [Los Alamos National Laboratory; Zepeda-Ruiz, L [Lawrence Livermore national Laboratory; Bringa, E. [CONICET, Universidad de Cuyo, Argentina; Nastasi, Mike [University of Nebraska, Lincoln, NE; Baldwin, Jon K. [Los Alamos National Laboratory

2012-08-28T23:59:59.000Z

393

Recovery of bypassed oil in the Dundee Formation using horizontal drains. Annual report, March 1996--March 1997  

SciTech Connect (OSTI)

This Class II field project has demonstrated that economic quantities of hydrocarbons can be produced from abandoned or nearly abandoned fields in the Dundee Formation of Central Michigan using horizontal drilling technology. The site selected for the demonstration horizontal well was Crystal Field, a nearly abandoned Dundee oil field in Montcalm County, Michigan. This field had produced over 8 million barrels of oil, mostly in the 1930`s and 1940`s. At the height of development, Crystal Field produced from 193 wells, but by 1995, only seven producing wells remained, each producing less than 10 bbls/day. A horizontal well, the TOW 1-3, drilled as a field demonstration pilot was successful, producing at rate of 100 bbls of oil per day with a zero water cut. Although the well is capable of producing at a of 500+ bbls/day, the production rate is being kept low deliberately to try to prevent premature water coning. Cumulative production exceeded 50,000 bbls of oil by the end of April, 1997 and lead to the permitting and licensing of several dozen Dundee wells by project end. Twelve of these permits were for continued development of Crystal Field. Two long horizontal wells were drilled successfully in Crystal after the TOW 1-3, but were disappointing economically. Core and logs from the Dundee interval were recovered from a vertical borehole at the same surface location. The addition of several horizontal wells will likely add another 2 million bbls (or more) to the cumulative production of the field over the next few years. If other abandoned Dundee fields are re-developed in a similar manner, the additional oil produced could exceed 80 million barrels.

NONE

1998-04-01T23:59:59.000Z

394

Seepage forces, important factors in the formation of horizontal hydraulic1 fractures and bedding-parallel fibrous veins ("beef" and "cone-in-cone")2  

E-Print Network [OSTI]

1 Seepage forces, important factors in the formation of horizontal hydraulic1 fractures and bedding24 may lead, either to tensile hydraulic fracturing, or to dilatant shear failure. We suggest that25 Terzaghi's concepts, leads to the conclusion that, for the18 fractures to be horizontal, either the rock

Paris-Sud XI, Université de

395

ARCS FOUNDATION GLOBAL IMPACT AWARD Global Health, Public Good and Graduate Education  

E-Print Network [OSTI]

ARCS FOUNDATION GLOBAL IMPACT AWARD Global Health, Public Good and Graduate Education Case Foundation Awards Luncheon in Atlanta on November 20, 2014. #12;Application Materials: 1) A letter

Arnold, Jonathan

396

The spectral irradiance traceability chain at PTB  

SciTech Connect (OSTI)

Spectral irradiance is a fundamental radiometric unit. Its application to measurement results requires qualified traceability to basic units of the international system of units (Systeme international d'unites, SI). The Physikalisch-Technische Bundesanstalt (PTB) is amongst other national metrological institutes (NMIs) responsible for the realization, maintenance and dissemination of various radiometric and photometric units based on and traceable to national standards. The unit of spectral irradiance is realized and represented by a blackbody-radiator as the national primary standard of the PTB. Based on Planck's radiation law, the irradiance is calculated and realized for any wavelength taking into account the exact knowledge of the radiation temperature and the geometrical parameters. Using a double-monochromator-based spectroradiometer system, secondary standard lamps can be calibrated by direct comparison to the blackbody-radiator (substitution method). These secondary standard lamps are then used at the PTB to calibrate standard lamps of customers. The customers themselves use these so-called transfer standards to calibrate their working standard lamps. These working standards are then used to calibrate own spectroradiometers or sources. This rather complex calibration chain is a common procedural method that for the customers generally leads to satisfying measurement results on site. Nevertheless, the standard lamps in use have to fulfill highest requirements concerning stability and reproducibility. Only this allows achieving comparably low transfer measurement uncertainties, which occur at each calibration step. Thus, the PTB is constantly investigating the improvement and further development of transfer standards and measurement methods for various spectral regions. The realization and dissemination of the spectral irradiance using the blackbody-radiator at the PTB is accomplished with worldwide approved minimized measurement uncertainties confirmed by international intercomparisons among NMIs. Ultimately, the spectral irradiance can be realized with expanded measurement uncertainties of far less than 1 % over a wide spectral range. Thus, for customers with high demands on low measurement uncertainties, it is possible to calibrate their working standards directly against the blackbody-radiator, taking into account the higher necessary effort. In special cases it is possible to calibrate the customer's spectroradiometric facilities directly in front of the blackbody-radiator. In the context of the European Metrology Research Project Traceability for surface spectral solar ultraviolet radiation, the traceability chain will be improved and adapted.

Sperfeld, P.; Pape, S.; Nevas, S. [Physikalisch-Technische Bundesanstalt, Bundesallee 10, 381160 Braunschweig (Germany)

2013-05-10T23:59:59.000Z

397

Evaluation of Neutron Irradiated Silicon Carbide and Silicon Carbide Composites  

SciTech Connect (OSTI)

The effects of fast neutron irradiation on SiC and SiC composites have been studied. The materials used were chemical vapor deposition (CVD) SiC and SiC/SiC composites reinforced with either Hi-Nicalon{trademark} Type-S, Hi-Nicalon{trademark} or Sylramic{trademark} fibers fabricated by chemical vapor infiltration. Statistically significant numbers of flexural samples were irradiated up to 4.6 x 10{sup 25} n/m{sup 2} (E>0.1 MeV) at 300, 500 and 800 C in the High Flux Isotope Reactor at Oak Ridge National Laboratory. Dimensions and weights of the flexural bars were measured before and after the neutron irradiation. Mechanical properties were evaluated by four point flexural testing. Volume increase was seen for all bend bars following neutron irradiation. Magnitude of swelling depended on irradiation temperature and material, while it was nearly independent of irradiation fluence over the fluence range studied. Flexural strength of CVD SiC increased following irradiation depending on irradiation temperature. Over the temperature range studied, no significant degradation in mechanical properties was seen for composites fabricated with Hi-Nicalon{trademark} Type-S, while composites reinforced with Hi-Nicalon{trademark} or Sylramic fibers showed significant degradation. The effects of irradiation on the Weibull failure statistics are also presented suggesting a reduction in the Weibull modulus upon irradiation. The cause of this potential reduction is not known.

Newsome G, Snead L, Hinoki T, Katoh Y, Peters D

2007-03-26T23:59:59.000Z

398

Comparison of optically measured and radar-derived horizontal neutral winds. Master's thesis  

SciTech Connect (OSTI)

Nighttime thermospheric winds for Sondrestrom, Greenland from 11 nights between 1983 and 1988, have been compared to learn about the O(+)-O collision cross section and the high-latitude atomic oxygen density. The horizontal winds in the magnetic meridian were derived indirectly from incoherent-scatter radar (ISR) measurements on ion velocities antiparallel to the magnetic field and directly from Fabry-Perot interferometer (FPI) measurements of Doppler shifts of the (6300-A) emission of atomic oxygen. In deriving the radar winds, the O(+)-O collision cross section, was scaled by a factor of f what was varied from 0.5 to 5.1. On the basis of several arguments the altitude of the 6300-A emission was assumed to be 230 km. The best agreement between the ISR and FPI winds was obtained when f was increased substantially, to between 1.7 and 3.4. If the average peak emission altitude were higher, these factors would be larger; if it were lower, they would be somewhat smaller. However, if the average altitude were substantially lower it would have been more difficult to have obtained agreement between the two techniques.

Christie, M.S.

1990-01-01T23:59:59.000Z

399

Modeling and analysis of ORNL horizontal storage tank mobilization and mixing  

SciTech Connect (OSTI)

The retrieval and treatment of radioactive sludges that are stored in tanks constitute a prevalent problem at several US Department of Energy sites. The tanks typically contain a settled sludge layer with non-Newtonian rheological characteristics covered by a layer of supernatant. The first step in retrieval is the mobilization and mixing of the supernatant and sludge in the storage tanks. Submerged jets have been proposed to achieve sludge mobilization in tanks, including the 189 m{sup 3} (50,000 gallon) Melton Valley Storage tanks (MVST) at Oak Ridge National Laboratory (ORNL) and the planned 378 m{sup 3} (100,000 gallon) tanks being designed as part of the MVST Capacity Increase Project (MVST-CIP). This report focuses on the modeling of mixing and mobilization in horizontal cylindrical tanks like those of the MVST design using submerged, recirculating liquid jets. The computer modeling of the mobilization and mixing processes uses the TEMPEST computational fluid dynamics program (Trend and Eyler 1992). The goals of the simulations are to determine under what conditions sludge mobilization using submerged liquid jets is feasible in tanks of this configuration, and to estimate mixing times required to approach homogeneity of the contents.

Mahoney, L.A.; Terrones, G.; Eyler, L.L.

1994-06-01T23:59:59.000Z

400

CFD Calculation of Internal Natural Convection in the Annulus between Horizontal Concentric Cylinders  

SciTech Connect (OSTI)

The objective of this heat transfer and fluid flow study is to assess the ability of a computational fluid dynamics (CFD) code to reproduce the experimental results, numerical simulation results, and heat transfer correlation equations developed in the literature for natural convection heat transfer within the annulus of horizontal concentric cylinders. In the literature, a variety of heat transfer expressions have been developed to compute average equivalent thermal conductivities. However, the expressions have been primarily developed for very small inner and outer cylinder radii and gap-widths. In this comparative study, interest is primarily focused on large gap widths (on the order of half meter or greater) and large radius ratios. From the steady-state CFD analysis it is found that the concentric cylinder models for the larger geometries compare favorably to the results of the Kuehn and Goldstein correlations in the Rayleigh number range of about 10{sup 5} to 10{sup 8} (a range that encompasses the laminar to turbulent transition). For Rayleigh numbers greater than 10{sup 8}, both numerical simulations and experimental data (from the literature) are consistent and result in slightly lower equivalent thermal conductivities than those obtained from the Kuehn and Goldstein correlations.

N.D. Francis, Jr; M.T. Itamura; S.W. Webb; D.L. James

2002-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Advanced Horizontal Well Recirculation Systems for Geothermal Energy Recovery in Sedimentary Formations  

SciTech Connect (OSTI)

There is increased recognition that geothermal energy resources are more widespread than previously thought, with potential for providing a significant amount of sustainable clean energy worldwide. Recent advances in drilling, completion, and production technology from the oil and gas industry can now be applied to unlock vast new geothermal resources, with some estimates for potential electricity generation from geothermal energy now on the order of 2 million megawatts. Terralog USA, in collaboration with the University of California, Irvine (UCI), are currently investigating advanced design concepts for paired horizontal well recirculation systems, optimally configured for geothermal energy recovery in permeable sedimentary and crystalline formations of varying structure and material properties. This two-year research project, funded by the US Department of Energy, includes combined efforts for: 1) Resource characterization; 2) Small and large scale laboratory investigations; 3) Numerical simulation at both the laboratory and field scale; and 4) Engineering feasibility studies and economic evaluations. The research project is currently in its early stages. This paper summarizes our technical approach and preliminary findings related to potential resources, small-scale laboratory simulation, and supporting numerical simulation efforts.

Mike Bruno; Russell L. Detwiler; Kang Lao; Vahid Serajian; Jean Elkhoury; Julia Diessl; Nicky White

2012-09-30T23:59:59.000Z

402

Technology assessment of vertical and horizontal air drilling potential in the United States. Final report  

SciTech Connect (OSTI)

The objective of the research was to assess the potential for vertical, directional and horizontal air drilling in the United States and to evaluate the current technology used in air drilling. To accomplish the task, the continental United States was divided into drilling regions and provinces. The map in Appendix A shows the divisions. Air drilling data were accumulated for as many provinces as possible. The data were used to define the potential problems associated with air drilling, to determine the limitations of air drilling and to analyze the relative economics of drilling with air versus drilling mud. While gathering the drilling data, operators, drilling contractors, air drilling contractors, and service companies were contacted. Their opinion as to the advantages and limitations of air drilling were discussed. Each was specifically asked if they thought air drilling could be expanded within the continental United States and where that expansion could take place. The well data were collected and placed in a data base. Over 165 records were collected. Once in the data base, the information was analyzed to determine the economics of air drilling and to determine the limiting factors associated with air drilling.

Carden, R.S.

1993-08-18T23:59:59.000Z

403

Characterization of Dosimetry of the BMRR Horizontal Thimble Tubes and Broad Beam Facility.  

SciTech Connect (OSTI)

The Brookhaven Medical Research Reactor was a 5 mega-watt, light-water cooled and heavy-graphite moderated research facility. It has two shutter-equipped treatment rooms, three horizontally extended thimble tubes, and an ex-core broad beam facility. The three experimental thimbles, or activation ports, external to the reactor tank were designed for several uses, including the investigations on diagnostic and therapeutic methods using radioactive isotopes of very short half-life, the analysis of radiation exposure on tissue-equivalent materials using a collimated neutron beam, and the evaluation of dose effects on biological cells to improve medical treatment. At the broad beam facility where the distribution of thermal neutrons was essential uniform, a wide variety of mammalian whole-body exposures were studied using animals such as burros or mice. Also studied at the broad beam were whole-body phantom experiments, involving the use of a neutron or photon beam streaming through a screen to obtain the flux spectrum suitable for dose analysis on the sugar-urea-water mixture, a tissue-equivalent material. Calculations of the flux and the dose at beam ports based on Monte Carlo particle-transport code were performed, and measurements conducted at the same tally locations were made using bare or cadmium-covered gold foils. Analytical results, which show good agreement with measurement data, are presented in the paper.

Hu,J.P.; Reciniello, R.N.; Holden, N.E.

2008-05-05T23:59:59.000Z

404

Tracing the Metal-Poor M31 Stellar Halo with Blue Horizontal Branch Stars  

E-Print Network [OSTI]

We have analyzed new HST/ACS and HST/WFC3 imaging in F475W and F814W of two previously-unobserved fields along the M31 minor axis to confirm our previous constraints on the shape of M31's inner stellar halo. Both of these new datasets reach a depth of at least F814W$blue horizontal branch (BHB) of the field as a distinct feature of the color-magnitude diagram. We measure the density of BHB stars and the ratio of BHB to red giant branch stars in each field using identical techniques to our previous work. We find excellent agreement with our previous measurement of a power-law for the 2-D projected surface density with an index of 2.6$^{+0.3}_{-0.2}$ outside of 3 kpc, which flattens to $\\alpha <$1.2 inside of 3 kpc. Our findings confirm our previous suggestion that the field BHB stars in M31 are part of the halo population. However, the total halo profile is now known to differ from this BHB profile, which suggests that we have isolated the metal-poor component. This component ...

Williams, Benjamin F; Gilbert, Eric F BellKaroline M; Guhathakurta, Puragra; Dorman, Claire; Lauer, Tod R; Seth, Anil C; Kalirai, Jason S; Rosenfield, Philip; Girardi, Leo

2015-01-01T23:59:59.000Z

405

Global Superdiffusion of Weak Chaos  

E-Print Network [OSTI]

A class of kicked rotors is introduced, exhibiting accelerator-mode islands (AIs) and {\\em global} superdiffusion for {\\em arbitrarily weak} chaos. The corresponding standard maps are shown to be exactly related to generalized web maps taken modulo an ``oblique cylinder''. Then, in a case that the web-map orbit structure is periodic in the phase plane, the AIs are essentially {\\em normal} web islands folded back into the cylinder. As a consequence, chaotic orbits sticking around the AI boundary are accelerated {\\em only} when they traverse tiny {\\em ``acceleration spots''}. This leads to chaotic flights having a quasiregular {\\em steplike} structure. The global weak-chaos superdiffusion is thus basically different in nature from the strong-chaos one in the usual standard and web maps.

Itzhack Dana

2003-10-20T23:59:59.000Z

406

Global Pollution: How Much Is Too Much?  

E-Print Network [OSTI]

009-0252-0 Global Pollution: How Much Is Too Much? Jack T.1) How much global pollution can our planet tolerate andThere is already more pollution on our planet than we can

Trevors, Jack T.; Saier, Milton H.

2009-01-01T23:59:59.000Z

407

Re-embedding the global soul  

E-Print Network [OSTI]

This thesis proposes to "re-embed" the "global nomad" into the context of an increasingly globalized world at the room scale. I define re-embedding as the "plugging in" of social relationships to local contexts and their ...

Wang, Joy (Joy Yuk-Hwa), 1975-

2001-01-01T23:59:59.000Z

408

Electronic Communities: Global Village or Cyberbalkans?  

E-Print Network [OSTI]

Electronic Communities: Global Village or Cyberbalkans? Marshall Van Alstyne Erik Brynjolfsson Tel KEYWORDS: Information Economy (AD02), Economic Theory (AM), Economic Impacts (BA01), Computerization of Society (BD0101), Organizational Structure (DA03), Information Flows (DD07), Globalization (AF1301

409

"How Can the WTO Help Harness Globalization?"  

E-Print Network [OSTI]

"How Can the WTO Help Harness Globalization?" "How Can the WTO Help Harness Globalization?" Public ForumPublic Forum WTOWTO20072007 4-5 October 20074-5 October 2007 #12;"How Can the WTO Help Harness

410

Ireland's Global University MSc World Heritage Conservation  

E-Print Network [OSTI]

for conservation · Cultural heritage, sustainable development and diversity · Global biodiversity and heritageIreland's Global University MSc World Heritage Conservation (Three Years Part Time) (Online facing conservation challenges, there is a growing need for professionals who understand how

411

Workforce Development in the Global Economy  

E-Print Network [OSTI]

Workforce Development in the Global Economy: LINKING SKILLS AND CAPABILITIES Phil Psilos & Competitiveness Duke University INTRODUCTION NOVEMBER 2011 #12;Workforce Development in the Global Economy competitiveness, and innovation in the knowledge economy. Duke CGGC works with a network of researchers

Richardson, David

412

Risk in the Global Supply Chain  

E-Print Network [OSTI]

Carbon footprints are not on the priority list of risk analysts in operations management for at least half or more of global businesses. What are the other risks in the global supply chain?

Datta, Shoumen

2006-01-01T23:59:59.000Z

413

ARM - What Causes Global Warming?  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc Documentation RUCProductstwrmrAre the Effects of Global Warming? Outreach Home Room

414

ARM - What is Global Warming?  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc Documentation RUCProductstwrmrAre the Effects of Global Warming? Outreach Home Outreach Homeis

415

ARM - What is Global Warming?  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc Documentation RUCProductstwrmrAre the Effects of Global Warming? Outreach Home Outreach Homeisis

416

Sandia National Laboratories: Global Climate & Energy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

20, 2013, in Advanced Materials Laboratory, Energy Efficiency, Facilities, Global Climate & Energy, Materials Science, Modeling, Modeling & Analysis, Partnership, Research &...

417

Increasing Global Renewable Energy Market Share  

E-Print Network [OSTI]

Increasing Global Renewable Energy Market Share: Recent Trends and Perspectives Final Report..............................................................................................................................12 2.2 Bioenergy

Peinke, Joachim

418

The Offshore Services Global Value Chain  

E-Print Network [OSTI]

The Offshore Services Global Value Chain ECONOMIC UPGRADING AND WORKFORCE DEVELOPMENT Karina & COMPETITIVENESS #12;The Offshore Services Global Value Chain: Economic Upgrading and Workforce Development "Skills & Competitiveness, Duke University Posted: November 17, 2011 #12;The Offshore Services Global Value Chain: Economic

Richardson, David

419

Conservation laws for non global Lagrangians  

E-Print Network [OSTI]

In the Lagrangian framework for symmetries and conservation laws of field theories, we investigate globality properties of conserved currents associated with non-global Lagrangians admitting global Euler--Lagrange morphisms. Our approach is based on the recent geometric formulation of the calculus of variations on finite order jets of fibered manifolds in terms of variational sequences.

A. Borowiec; M. Ferraris; M. Francaviglia; M. Palese

2005-05-13T23:59:59.000Z

420

The Emerging Chinese economy & its Global Impacts  

E-Print Network [OSTI]

The Emerging Chinese economy & its Global Impacts Department of Geography & IDS University of Sussex 5 February: The Emerging Chinese Economy & its Global Impacts + Decoding the Harmonious Socialist of Leicester 19 February: Global Production Network & the Chinese Economy Prof. John Humphrey, IDS 26 February

Sussex, University of

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Global Optimization in Generalized Geometric Programming  

E-Print Network [OSTI]

exchangernetwork design 5], chemical reactor design 2, 6], optimal condenser design 7], oxygen production 8Global Optimization in Generalized Geometric Programming Costas D. Maranas1 and Christodoulos A Abstract A deterministic global optimization algorithm is proposed for locating the global minimum

Maranas, Costas

422

Rangeland ecology: Key global research issues & questions  

E-Print Network [OSTI]

1 Rangeland ecology: Key global research issues & questions Robin Reid1 and Maria Fernandez Ecology Lab 2Associate Professor Colorado State University, Fort Collins, Colorado, USA Global Issues and Questions in Rangeland Ecology · Despite the focus here on global issues, we need to recognize that Mongolia

423

Global optimization in inverse problem of scatterometry  

E-Print Network [OSTI]

Global optimization in inverse problem of scatterometry Lekbir Afraites1,2 Jerome Hazard3 Patrick as a parametric optimization problem using the Least Square criterion. In this work, a design procedure for global robust optimization is developed using Kriging and global optimization approaches. Robustness

Paris-Sud XI, Université de

424

An Explanation of Global Warming without Supercomputing  

E-Print Network [OSTI]

An Explanation of Global Warming without Supercomputing (revised version) K. Miyazaki E that the anthropogenic global warming is severely limited because the Earth is a water planet. 1 Introduction Now,2,3] on this anthropogenic global warming (AGW) is essentially based on the results of elaborate and enormous computer

425

Global Warming: The Threat to the Planet*  

E-Print Network [OSTI]

Global Warming: The Threat to the Planet* Jim Hansen 17 April 2007 2007 Leo Szilard Lecture. Graham Red Squirrel #12;Survival of Species 1. "Business-as-Usual" Scenario - Global Warming ~ 3ºC - Likely Extinctions ~ 50 percent 2. "Alternative" Scenario - Global Warming ~ 1ºC - Likely Extinctions

Hansen, James E.

426

An Explanation of Global Warming without Supercomputing  

E-Print Network [OSTI]

An Explanation of Global Warming without Supercomputing K. Miyazaki E-mail: miyazakiro that the climate sensitivity never exceeds 6 C. Consequently, the anthropogenic global warming is severely limited be calculated in simple terms. Global warming is like that." However, there will be not a few physicists who do

427

4, 40694124, 2007 Global-scale  

E-Print Network [OSTI]

into evapotranspiration and total runoff. We estimate that global groundwater recharge was 12 666 km3 /yr for the climateHESSD 4, 4069­4124, 2007 Global-scale modeling of groundwater recharge P. D¨oll and K. Fiedler System Sciences Global-scale modeling of groundwater recharge P. D¨oll and K. Fiedler Institute

Boyer, Edmond

428

Josephson Junctions and Devices fabricated by Focused Electron Beam Irradiation  

E-Print Network [OSTI]

Josephson Junctions and Devices fabricated by Focused Electron Beam Irradiation Wilfred Edwin Booij Gonville and Caius College Cambridge A dissertation submitted for the degree of Doctor of Philosophy at the University of Cambridge December 1997... Summary Josephson Junctions and Devices fabricated by Focused Electron Beam Irradiation The irradiation of high Tc superconducting thin films with a focused electron beam, such as that obtained in a scanning transmission electron microscope (STEM), can...

Booij, Wilfred Edwin

429

NANOSTRUCTURE PATTERNING UNDER ENERGETIC PARTICLE BEAM IRRADIATION  

SciTech Connect (OSTI)

Energetic ion bombardment can lead to the development of complex and diverse nanostructures on or beneath the material surface through induced self-organization processes. These self-organized structures have received particular interest recently as promising candidates as simple, inexpensive, and large area patterns, whose optical, electronic and magnetic properties are different from those in the bulk materials [1-5]. Compared to the low mass efficiency production rate of lithographic methods, these self-organized approaches display new routes for the fabrication of nanostructures over large areas in a short processing time at the nanoscale, beyond the limits of lithography [1,4]. Although it is believed that surface nanostructure formation is based on the morphological instability of the sputtered surface, driven by a kinetic balance between roughening and smoothing actions [6,7], the fundamental mechanisms and experimental conditions for the formation of these nanostructures has still not been well established, the formation of the 3-D naopatterns beneath the irradiated surface especially needs more exploration. During the last funding period, we have focused our efforts on irradiation-induced nanostructures in a broad range of materials. These structures have been studied primarily through in situ electron microscopy during electron or ion irradiation. In particular, we have performed studies on 3-D void/bubble lattices (in metals and CaF2), embedded sponge-like porous structure with uniform nanofibers in irradiated semiconductors (Ge, GaSb, and InSb), 2-D highly ordered pattern of nanodroplets (on the surface of GaAs), hexagonally ordered nanoholes (on the surface of Ge), and 1-D highly ordered ripple and periodic arrays (of Cu nanoparticles) [3,8-11]. The amazing common feature in those nanopatterns is the uniformity of the size of nanoelements (nanoripples, nanodots, nanovoids or nanofibers) and the distance separating them. Our research focuses on the understanding of fundamental scientific basis for the irradiation-induced self-organization processes. The fundamental physical mechanisms underlying ordered pattern formation, which include defect production and migration, ion sputtering, redeposition, viscous flow and diffusion, are investigated through a combination of modeling and in situ and ex-situ observations [3,9,11]. In addition, these nanostructured materials exhibit considerable improvement of optical properties [9,12,13]. For example, patterned Ge with a hexagonally ordered, honeycomb-like structure of nanoscale holes possesses a high surface area and a considerably blue-shifted energy gap [9], and oxidation of ordered Ga droplets shows noticeable enhancement of optical transmission [12]. This research has addressed nanopattern formation in a variety of materials under ion bombardment and provided a fundamental understanding of the dynamic mechanisms involved. In addition, have also stared to systematically investigate pattern formation under ion irradiation for more systems with varied experimental conditions and computation, including the collaboration with Dr. Veena Tikare of Sandia National Laboratory with a hybrid computation method at the ending this grant. A more detailed relationship between nanostructure formation and experimental conditions will be revealed with our continued efforts.

Wang, Lumin [Regents of the University of Michigan; Lu, Wei [Regents of the University of Michigan

2013-01-31T23:59:59.000Z

430

Solar and Infrared Radiation Station (SIRS) Handbook  

SciTech Connect (OSTI)

The Solar Infrared Radiation Station (SIRS) provides continuous measurements of broadband shortwave (solar) and longwave (atmospheric or infrared) irradiances for downwelling and upwelling components. The following six irradiance measurements are collected from a network of stations to help determine the total radiative flux exchange within the Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) Climate Research Facility: • Direct normal shortwave (solar beam) • Diffuse horizontal shortwave (sky) • Global horizontal shortwave (total hemispheric) • Upwelling shortwave (reflected) • Downwelling longwave (atmospheric infrared) • Upwelling longwave (surface infrared)

Stoffel, T

2005-07-01T23:59:59.000Z

431

Thermodynamic Evaluation of Low-Global Warming Potential Refrigerants...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Evaluation of Low-Global-Warming-Potential Refrigerants Research & Development Roadmap: Next-Generation Low Global Warming Potential Refrigerants Next Generation Low-Global...

432

Saskia Sassen and the Sociology of Globalization: A Critical Appraisal  

E-Print Network [OSTI]

Economic globalization denationalizes national economies andGlobalization and the Postcolonial World: The New Political Economywidely on globalization from a political-economy approach.

Robinson, William I.

2009-01-01T23:59:59.000Z

433

The Global Nuclear Energy Partnership | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

The Global Nuclear Energy Partnership The Global Nuclear Energy Partnership An article describing the small scale reactors in the GNEP. The Global Nuclear Energy Partnership More...

434

A Model of Success: The Carnegie Institute for Global Ecology  

E-Print Network [OSTI]

Carnegie Institute for Global Ecology Kirstin Weeks, DavidInstitute for Global Ecology, the answer is an unquali? edremarkable about the Global Ecology building is not only how

Weeks, Kirstin; Lehrer, David; Bean, Jonathan

2007-01-01T23:59:59.000Z

435

Global Research on On The Verge | GE Global Research  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFun with Big Sky LearningGet Assistance GetGiantOn The Verge Visits GE's Global

436

A Simplified Shuttle Irradiation Facility for ATR  

SciTech Connect (OSTI)

During the past fifteen years there has been a steady increase in the demand for radioisotopes in nuclear medicine and a corresponding decline in the number of reactors within the U.S. capable of producing them. The Advanced Test Reactor (ATR) is the largest operating test reactor in the U.S., but its isotope production capabilities have been limited by the lack of an installed isotope shuttle irradiation system. A concept for a simple “low cost” shuttle irradiation facility for ATR has been developed. Costs were reduced (in comparison to previous ATR designs) by using a shielded trough of water installed in an occupiable cubicle as a shielding and contamination control barrier for the send and receive station. This shielding concept also allows all control valves to be operated by hand and thus the need for an automatic control system was eliminated. It was determined that 4 – 5 ft of water would be adequate to shield the isotopes of interest while shuttles are transferred to a small carrier. An additional feature of the current design is a non-isolatable by-pass line, which provides a minimum coolant flow to the test region regardless of which control valves are opened or closed. This by-pass line allows the shuttle facility to be operated without bringing reactor coolant water into the cubicle except for send and receive operations. The irradiation position selected for this concept is a 1.5 inch “B” hole (B-11). This position provides neutron fluxes of approximately: 1.6 x 1014 (<0.5 eV) and 4.0 x 1013 (>0.8 MeV) n/cm2*sec.

Palmer, Alma Joseph; Laflin, S. T.

1999-09-01T23:59:59.000Z

437

Emulation of reactor irradiation damage using ion beams  

SciTech Connect (OSTI)

The continued operation of existing light water nuclear reactors and the development of advanced nuclear reactor depend heavily on understanding how damage by radiation to levels degrades materials that serve as the structural components in reactor cores. The first high dose ion irradiation experiments on a ferritic-martensitic steel showing that ion irradiation closely emulates the full radiation damage microstructure created in-reactor are described. Ferritic-martensitic alloy HT9 (heat 84425) in the form of a hexagonal fuel bundle duct (ACO-3) accumulated 155 dpa at an average temperature of 443°C in the Fast Flux Test Facility (FFTF). Using invariance theory as a guide, irradiation of the same heat was conducted using self-ions (Fe++) at 5 MeV at a temperature of 460°C and to a dose of 188 displacements per atom. The void swelling was nearly identical between the two irradiations and the size and density of precipitates and loops following ion irradiation are within a factor of two of those for neutron irradiation. The level of agreement across all of the principal microstructure changes between ion and reactor irradiations establishes the capability of tailoring ion irradiations to emulate the reactor-irradiated microstructure.

G. S. Was; Z. Jiao; E. Beckett; A. M. Monterrosa; O. Anderoglu; B. H. Sencer; M. Hackett

2014-10-01T23:59:59.000Z

438

Microsoft Word - Analysis of Deformation Mode Changes in Irradiated...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

steels); however, in many cases they may have a negative impact on material performance (hydrogen embrittlement of bcc-phase, etc.). Irradiation leads to defects accumulation,...

439

Irradiation Effects on Human Cortical Bone Fracture Behavior  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Irradiation Effects on Human Cortical Bone Fracture Behavior Print Human bone is strong but still fallible. To better predict fracturing in bone, researchers need a mechanistic...

440

alpha particle irradiation: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

5 Incidence characteristics of alpha particles on detectors irradiated in a radon progeny atmosphere Biology and Medicine Websites Summary: Incidence characteristics of...

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

alpha particles irradiation: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

5 Incidence characteristics of alpha particles on detectors irradiated in a radon progeny atmosphere Biology and Medicine Websites Summary: Incidence characteristics of...

442

alpha particle irradiated: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

5 Incidence characteristics of alpha particles on detectors irradiated in a radon progeny atmosphere Biology and Medicine Websites Summary: Incidence characteristics of...

443

apres irradiation alpha: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Edmond 8 Incidence characteristics of alpha particles on detectors irradiated in a radon progeny atmosphere Biology and Medicine Websites Summary: Incidence characteristics of...

444

Modification of Defect Structures in Graphene by Electron Irradiation...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Modification of Defect Structures in Graphene by Electron Irradiation: Ab Initio Molecular Dynamics Simulations. Modification of Defect Structures in Graphene by Electron...

445

Dynamic Recovery in Silicate-Apatite Structures Under Irradiation...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Recovery in Silicate-Apatite Structures Under Irradiation and Implications for Long-Term Immobilization of Actinides. Dynamic Recovery in Silicate-Apatite Structures Under...

446

Global Mineral Resource Assessment Potash--A Global Overview of Evaporite-Related Potash  

E-Print Network [OSTI]

Global Mineral Resource Assessment Potash--A Global Overview of Evaporite-Related Potash Resources intentionally left blank. #12;Global Mineral Resource Assessment Michael L. Zientek, Jane M. Hammarstrom, and Kathleen M. Johnson, editors Potash--A Global Overview of Evaporite-Related Potash Resources, Including

Fleskes, Joe

447

Graduate Certificate in Global Health Fact Sheet College of Public Health GRADUATE EDUCATION IN GLOBAL HEALTH  

E-Print Network [OSTI]

Graduate Certificate in Global Health Fact Sheet · College of Public Health GRADUATE EDUCATION. Educational Objectives for the Graduate Certificate in Global Health Increase understanding of the global-disciplinary education in global health, electives and internships will be expected by student involvement with various

Arnold, Jonathan

448

Impact of global dimming and brightening on global warming Martin Wild,1  

E-Print Network [OSTI]

Impact of global dimming and brightening on global warming Martin Wild,1 Atsumu Ohmura,1 and Knut February 2007. [1] Speculations on the impact of variations in surface solar radiation on global warming was responsible for the observed warming. To disentangle surface solar and greenhouse influences on global warming

Fischlin, Andreas

449

Global Biodiesel Market Trends,Global Biodiesel Market Trends, Outlook and OpportunitiesOutlook and Opportunities  

E-Print Network [OSTI]

Global Biodiesel Market Trends,Global Biodiesel Market Trends, Outlook and OpportunitiesPresident, Emerging Markets Online http://www.emerginghttp://www.emerging--markets.commarkets.com Author, Biodiesel 2020: A Global Market SurveyAuthor, Biodiesel 2020: A Global Market Survey Columnist

450

Increase of global monsoon area and precipitation under global warming: A robust signal?  

E-Print Network [OSTI]

) and the global monsoon total precipitation (GMP) have increased during 1979­2008 [Hsu et al., 2011; Wang et alIncrease of global monsoon area and precipitation under global warming: A robust signal? Pang of people around the world. The global monsoon precipitation had an increasing trend over the past three

Li, Tim

451

Microstructural examination of irradiated vanadium alloys  

SciTech Connect (OSTI)

Microstructural examination results are reported for a V-5Cr-5Ti unirradiated control specimens of heat BL-63 following annealing at 1050{degrees}C, and V-4Cr-4Ti heat BL-47 irradiated in three conditions from the DHCE experiment: at 425{degrees}C to 31 dpa and 0.39 appm He/dpa, at 600{degrees}C to 18 dpa and 0.54 appm He/dpa and at 600{degrees}C to 18 dpa and 4.17 appm He/dpa.

Gelles, D.S. [Pacific Northwest National Lab., Richland, WA (United States); Chung, H.M. [Argonne National Lab., IL (United States)

1997-04-01T23:59:59.000Z

452

Mitigation of irradiation embrittlement by annealing  

SciTech Connect (OSTI)

The main results of a complex investigation carried out in Russia of post irradiation annealing and reembrittlement of WWER-440 reactor pressure vessel materials are presented. The dependence of the Charpy transition temperature recovery on annealing temperature and fluence was established. Charpy specimens were reirradiated after annealing at 340, 380, 420, and 460 C. Experimental values of the Charpy transition temperature after reirradiation are compared to that predicted by three methods. At annealing temperatures equal to or above 420 C, results of the analysis indicate that, of the methods investigated, the lateral shift method gives the best result for estimating the transition temperature shift due to reirradiation.

Amayev, A.D.; Kryukov, A.M.; Levit, V.I.; Platonov, P.A.; Sokolov, M.A. [Kurchatov Inst., Moscow (Russian Federation)

1996-12-31T23:59:59.000Z

453

Irradiation-induced effects of proton irradiation on zirconium carbides with different stoichiometries  

SciTech Connect (OSTI)

Zirconium carbide (ZrC) is being considered for utilization in deep burn TRISO fuel particles for hightemperature, gas-cooled reactors. Zirconium carbide has a cubic B1 type crystal structure along with a very high melting point (3420 ?C), exceptional hardness and good thermal and electrical conductivities. Understanding the ZrC irradiation response is crucial for establishing ZrC as an alternative component in TRISO fuel. Until now, very few studies on irradiation effects on ZrC have been released and fundamental aspects of defect evolution and kinetics are not well understood although some atomistic simulations and phenomenological studies have been performed. This work was carried out to understand the damage evolution in float-zone refined ZrC with different stoichiometries. Proton irradiations at 800 ?C up to doses of 3 dpa were performed on ZrCx (where x ranges from 0.9 to 1.2) to investigate the damage evolution. The irradiation-induced defects, such as density of dislocation loops, at different stoichiometries and doses which were characterized by transmission electron microscopy (TEM) is presented and discussed.

Y. Huang; B.R. Maier; T.R. Allen

2014-10-01T23:59:59.000Z

454

Structural effects of unsteady aerodynamic forces on horizontal-axis wind turbines  

SciTech Connect (OSTI)

Due to its renewable nature and abundant resources, wind energy has the potential to fulfill a large portion of this nation`s energy needs. The simplest means of utilizing wind energy is through the use of downwind, horizontal-axis wind turbines (HAWT) with fixed-pitch rotors. This configuration regulates the peak power by allowing the rotor blade to aerodynamically stall. The stall point, the point of maximum coefficient of lift, is currently predicted using data obtained from wind tunnel tests. Unfortunately, these tests do not accurately simulate conditions encountered in the field. Flow around the tower and nacelle coupled with inflow turbulence and rotation of the turbine blades create unpredicted aerodynamic forces. Dynamic stall is hypothesized to occur. Such aerodynamic loads are transmitted into the rotor and tower causing structural resonance that drastically reduces the design lifetime of the wind turbine. The current method of alleviating this problem is to structurally reinforce the tower and blades. However, this adds unneeded mass and, therefore, cost to the turbines. A better understanding of the aerodynamic forces and the manner in which they affect the structure would allow for the design of more cost effective and durable wind turbines. Data compiled by the National Renewable Energy Laboratory (NREL) for a downwind HAWT with constant chord, untwisted, fixed-pitch rotors is analyzed. From these data, the actual aerodynamic characteristics of the rotor are being portrayed and the potential effects upon the structure can for the first time be fully analyzed. Based upon their understanding, solutions to the problem of structural resonance are emerging.

Miller, M.S.; Shipley, D.E. [Univ. of Colorado, Boulder, CO (United States). BioServe Space Technologies

1994-08-01T23:59:59.000Z

455

One Component Two Phase Flow in Horizontal and Vertical Ducts: Some Basic Considerations  

SciTech Connect (OSTI)

For a description and analysis of the flow they consider the conservation equations of the two phases separately, but in thermal and mechanical equilibrium, coupled by the itnerface shear forces (two fluid model, drift flux model). Coupling may be weak or strong, depending on Froude and Mach numbers of the flow. The fluid is highly compressible, not because the individual phases move at such speeds that their individual density changes are significant but because evapiration (phase change) results in large density changes of the system at moderate pressure or temperature changes once flashing occurs. The slip between the phases is caused by unequal wall shear stress, acceleration of the fluid or gravitational forces and is hindered by the interface interaction. if they denote by {gamma} the ratio of the liquid density to the vapor density and by {sigma} the ratio of the vapor speed to the liquid speed they find that in horizontal flows {sigma} = {gamma}{sup 1/2} yields the maximum slip (neglecting acceleration effects) that can be reached with no interface force acting (assuming equal friction coefficients for both phases at the wall). If one investigates the conditions of thermodynamic flow similarity between different substances in two phase flow, one finds that the latent heat of vaporization is the principal controlling parameter. Thus, a 5 cm diameter test section in two phase R-114, at room temperature, corresponds to a 30 cm diameter duct in water-steam at boiling conditions at high temperatures such as encountered in geothermal and other power production systems.

Maeder, Paul F.; Dickinson, David A.; Nikitopoulos, Dimitris E.

1983-12-15T23:59:59.000Z

456

Shear horizontal surface acoustic wave microsensor for Class A viral and bacterial detection.  

SciTech Connect (OSTI)

The rapid autonomous detection of pathogenic microorganisms and bioagents by field deployable platforms is critical to human health and safety. To achieve a high level of sensitivity for fluidic detection applications, we have developed a 330 MHz Love wave acoustic biosensor on 36{sup o} YX Lithium Tantalate (LTO). Each die has four delay-line detection channels, permitting simultaneous measurement of multiple analytes or for parallel detection of single analyte containing samples. Crucial to our biosensor was the development of a transducer that excites the shear horizontal (SH) mode, through optimization of the transducer, minimizing propagation losses and reducing undesirable modes. Detection was achieved by comparing the reference phase of an input signal to the phase shift from the biosensor using an integrated electronic multi-readout system connected to a laptop computer or PDA. The Love wave acoustic arrays were centered at 330 MHz, shifting to 325-328 MHz after application of the silicon dioxide waveguides. The insertion loss was -6 dB with an out-of-band rejection of 35 dB. The amplitude and phase ripple were 2.5 dB p-p and 2-3{sup o} p-p, respectively. Time-domain gating confirmed propagation of the SH mode while showing suppression of the triple transit. Antigen capture and mass detection experiments demonstrate a sensitivity of 7.19 {+-} 0.74{sup o} mm{sup 2}/ng with a detection limit of 6.7 {+-} 0.40 pg/mm{sup 2} for each channel.

Branch, Darren W.; Huber, Dale L.; Brozik, Susan Marie; Edwards, Thayne L.

2008-10-01T23:59:59.000Z

457

Improved sweep efficiency through the application of horizontal well technology in a mature combustion EOR project: Battrum Field, Saskatchewan, Canada  

SciTech Connect (OSTI)

In-situ combustion has been employed in the Battrum field since 1964. Although the field has responded favorably to combustion, efficiency of the horizontal displacement process appears to be poor in some areas of the field. Injected air and combustion gases accumulate at the top of the reservoir, and injected water moves into a zone of relatively high mobile water saturation, occurring at the base of the reservoir. Rapid breakthrough of the injected fluids increases operating costs due to high gas-oil ratios. Placement of horizontal wells below the combustion gas cap, and conversion to a vertical displacement process is expected to increase oil rate, improve oil recovery, and reduce operating costs.

Ames, B.G.; Grams, R.E.; Pebdani, F.N. [Mobil Oil Canada, Alberta (Canada)

1995-02-01T23:59:59.000Z

458

Economic Globalization and a Nuclear Renaissance  

SciTech Connect (OSTI)

The phenomenon of globalization has become increasingly well recognized, documented, and analyzed in the last several years. Globalization, the integration of markets and intra-firm competition on a worldwide basis, involves complex behavioral and mindset changes within a firm that facilitate global competition. The changes revolve around efficient information flow and rapid deployment of technology. The objective of this report is to examine the probable characteristics of a global nuclear renaissance and its broad implications for industry structure and export control relative to nuclear technology. The question of how a modern renaissance would affect the trend toward globalization of the nuclear industry is addressed.

Wood, Thomas W.; Johnson, Wayne L.; Parker, Brian M.

2001-10-22T23:59:59.000Z

459

Estimating direct, diffuse, and global solar radiation for various cities in Iran by two methods and their comparison with the measured data  

SciTech Connect (OSTI)

Two computational methods for calculating hourly, daily, and monthly average values of direct, diffuse, and global solar radiation on horizontal collectors have been presented in this article for location with different latitude, altitude, and atmospheric conditions in Iran. These methods were developed using two different independent sets of measured data from the Iranian Meteorological Organization (IMO) for two cities in Iran (Tehran and Isfahan) during 14 years of measurement for Tehran and 4 years of measurement for Isfahan. Comparison of calculated monthly average global solar radiation, using the two models for Tehran and Isfahan with measured data from the IMO, has indicated a good agreement between them. Then these developed methods were extended to another location (city of Bandar-Abbas), where measured data are not available. But the work of Daneshyar predicts its monthly global radiation. The maximum discrepancy of 7% between the developed models and the work of Daneshyar was observed.

Ashjaee, M.; Roomina, M.R.; Ghafouri-Azar, R. (Univ. of Tehran (Iran, Islamic Republic of))

1993-05-01T23:59:59.000Z

460

Tectonic "short circuit" of sub-horizontal fluid-saturated bodies as a possible mechanism of the earthquake  

E-Print Network [OSTI]

An alternative earthquake mechanism is proposed. The traditional stress mechanism of fracture formation assigned a support role. As a proximate cause of the earthquake the destruction of the roofs of sub-horizontal fluid-saturated bodies (SHFB) is considered. This collapse may occur due to redistribution of fluid pressure within the system of SHFB connected by cracks (tectonic or other nature). It can cause both shifts of rock blocks contributing to seismic shocks and various effects characteristic of foreshocks and aftershocks.

Andrei Nechayev

2013-07-18T23:59:59.000Z

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Evolution of the nanostructure OF VVER-1000 RPV materials under neutron irradiation and post irradiation annealing  

SciTech Connect (OSTI)

A high nickel VVER-1000 (15Kh2NMFAA) base metal (1.34 wt% Ni, 0.47% Mn, 0.29% Si and 0.05% Cu), and a high nickel (12Kh2N2MAA) weld metal (1.77 wt% Ni, 0.74% Mn, 0.26% Si and 0.07% Cu) have been characterized by atom probe tomography to determine the changes in the microstructure during neutron irradiation to high fluences. The base metal was studied in the unirradiated condition and after neutron irradiation to fluences between 2.4 and 14.9 x 10{sup 23} m{sup -2} (E > 0.5 MeV), and the weld metal was studied in the unirradiated condition and after neutron irradiation to fluences between 2.4 and 11.5 x 10{sup 23} m{sup -2} (E > 0.5 MeV). High number densities of 2-nm-diameter Ni-, Si- and Mn-enriched nanoclusters were found in the neutron irradiated base and weld metals. No significant copper enrichment was associated with these nanoclusters and no copper-enriched precipitates were observed. The number densities of these nanoclusters correlate with the shifts in the {Delta}T{sub 41 J} ductile-to-brittle transition temperature. These nanoclusters were present after a post irradiOffice of Science (US)C, but had dissolved into the matrix after 24 h at 450 C. Phosphorus, nickel, silicon and to a lesser extent manganese were found to be segregated to the dislocations.

Miller, Michael K [ORNL; Chernobaeva, A. A. [Russian Research Center, Kurchatov Institute, Moscow, Russia; Shtrombakh, Ya. [Russian Research Center, Kurchatov Institute, Moscow, Russia; Erak, D. [Russian Research Center, Kurchatov Institute, Moscow, Russia; Zabusov, Oleg O. [Russian Research Center, Kurchatov Institute, Moscow, Russia; Russell, Kaye F [ORNL; Nanstad, Randy K [ORNL

2009-01-01T23:59:59.000Z

462

Recovery of bypassed oil in the Dundee Formation using horizontal drains. Annual report, April 1994--June 1995  

SciTech Connect (OSTI)

Crystal Field in Montcalm County, MI, was selected as a field trial site for this project. Analysis of production data for Crystal Field suggests that an additional 200,000 bbls of oil can be produced using one strategically located horizontal well. Total addition production from the Crystal Field could be as much as 6--8 MMBO. Application of the technology developed in this project to other Dundee fields in the area has the potential to increase Dundee production in Michigan by 35%, adding 80--100 MMBO to ultimate recovery. This project will demonstrate through a field trial that horizontal wells can be substantially increase oil production in older reservoirs that are at or near their economic limit. To maximize the potential of the horizontal well and to ensure that a comprehensive evaluation can be made, extensive reservoir characterization will be performed. In addition to the proposed field trial at Crystal Field, 29 additional Dundee fields in a seven-county area have been selected for study in the reservoir characterization portion of this project.

Wood, J.

1995-08-01T23:59:59.000Z

463

Ordovician Red River {open_quotes}B{close_quotes}: Horizontal oil play in the southern Williston basin  

SciTech Connect (OSTI)

Recent application of horizontal drilling technology to the Ordovician Red River {open_quotes}B{close_quotes} zone in the southern Williston basin has resulted in a successful oil play, with more than 100 wells drilled in 1995 and 1996. The Red River {open_quotes}B{close_quotes} reservoir is a dolomitized laminated carbonate with microsucrosic porosity of 8-25% and permeabilities in the range of 1-66 md. It occurs within the middle of three depositional cycles ({open_quotes}A,{close_quotes} {open_quotes}B,{close_quotes} and {open_quotes}C{close_quotes}) that form the upper Red River Formation. Each cycle consists of a lower burrowed limestone, middle laminated member, and capping anhydrite or lime mudstone. The {open_quotes}B{close_quotes} reservoir is confined to the {open_quotes}B{close_quotes} laminated member and consists of an upper portion, characterized by better reservoir quality, and a lower, less permeable portion. Horizontal drilling has the advantage of significantly increasing well-bore exposure to the upper, more permeable portion. Well data indicate the total Red River {open_quotes}B{close_quotes} porosity zone has remarkable extent over parts of southwestern North Dakota, southeastern Montana, and northwestern South Dakota. Productivity from horizontal well displays considerable variation that can be correlated with structure/tectonic patterns and with reservoir petrophysical character.

Montgomery, S.L.

1997-04-01T23:59:59.000Z

464

Global searches at the Tevatron  

SciTech Connect (OSTI)

We present a review of global searches at the Tevatron with D0 and CDF detectors. The strategy involves splitting the data from the Tevatron into many final states and looking for signs of new physics in the high p{sub T} tails of various distributions using SLEUTH algorithm. CDF also utilizes Bump Hunter to search for narrow resonances in mass distributions. We analyzed 180 D0 final states, 9335 D0 distributions; 399 CDF final states and 19650 CDF distributions. No evidence of new physics is found.

Renkel, Peter; /Southern Methodist U.

2009-01-01T23:59:59.000Z

465

ARM - Lesson Plans: Global Warming  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc Documentation RUC : XDCResearch Related InformationAcid Rain Outreach HomeExpansion ofGlobal

466

ARM - What Causes Global Warming?  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc Documentation RUCProductstwrmrAre the Effects of Global Warming? Outreach Home RoomThinkersWhat

467

Endeavor Global | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address:011-DNA Jump37. It is classifiedProject) |Emeryville,EmpireGlobal Jump to: navigation,

468

Dissolution of ordered precipitates under ion irradiation  

SciTech Connect (OSTI)

The stability of the ordered {gamma}{prime} precipitates under 300-keV Ni{sup +} irradiation was investigated between room temperature and 623 K. The two competing mechanisms of destabilization by cascade producing irradiation, i.e. disordering and dissolution of the {gamma}{prime} precipitates in Nimonic PE16 alloy, has been studied separately by electron microscopy and field-ion microscopy with atom probe. At high temperatures, the precipitates are stable. At intermediate temperatures, the precipitates dissolve by ballistic mixing into the matrix, but the interface is restored by the radiation-enhanced atomic jumps. The order in the precipitates remains stable. At low temperatures, the precipitates are dissolved by atomic mixing. The dissolution proceeds in a diffusional manner with a diffusion coefficient normalized by the displacement rate D/K = 0.75 nm{sup 2}dpa{sup {minus}1}. The precipitates become disordered by a fluence of 0.1 dpa, whereas precipitate dissolution needs much higher fluences.

Camus, E.; Bourdeau, F.; Abromeit, C.; Wanderka, N.; Wollenberger, H. [Hahn-Meitner-Institut Berlin GmbH (Germany)

1995-09-01T23:59:59.000Z

469

Phase transformations in neutron-irradiated Zircaloys  

SciTech Connect (OSTI)

Microstructural evolution in Zircaloy-2 and -4 spent-fuel cladding specimens after approx.3 years of irradiation in commercial power reactors has been investigated by TEM and HVEM. Two kinds of precipitates induced by the fast-neutron irradiation in the reactors have been identified, i.e., Zr/sub 3/O and cubic-ZrO/sub 2/ particles approximately 2 to 10 nm in size. By means of a weak-beam dark-field ''2-1/2D-microscopy'' technique, the bulk nature of the precipitates and the surficial nature of artifact oxide and hydride phases could be discerned. The Zr(Fe/sub x/,Cr/sub 1-x/)/sub 2/ and Zr/sub 2/(Fe/sub x/,Ni/sub 1-x/) intermetallic precipitates normally present in the as-fabricated material virtually dissolved in the spent-fuel cladding specimens after a fast-neutron fluence of approx.4 x 10/sup 21/ ncm/sup -2/ in the power reactors. The observed radiation-induced phase transformations are compared with predictions based on the currently available understanding of the alloy characteristics. 29 refs.

Chung, H.M.

1986-04-01T23:59:59.000Z

470

A Simplified Shuttle Irradiation Facility for ATR  

SciTech Connect (OSTI)

During the past fifteen years there has been a steady increase in the demand for radioisotopes in nuclear medicine and a corresponding decline in the number of reactors within the U.S. capable of producing them. The Advanced Test Reactor (ATR) is the largest operating test reactor in the U.S., but its isotope production capabilities have been limited by the lack of an installed isotope shuttle irradiation system. A concept for a simple "low cost" shuttle irradiation facility for ATR has been developed. Cost were reduced (in comparison to previous ATR designs) by using a shielded trough of water installed in an occupiable cubicle as a shielding and contamination control barrier for the send and receive station. This shielding concept also allows all control valves to be operated by hand and thus the need for an automatic control system was eliminated. It was determined that 4-5 ft of water would be adequate to shield the isotopes of interest while shuttles are transferred to a small carrier. An additional feature of the current design is a non-isolatable by-pass line, which provides a minimum coolant flow to the test region regardless of which control valves are opened or closed. This by-pass line allows the shuttle facility to be operated without bringing reactor coolant water into the cubicle except for send and receive operations.

A. J. Palmer; S. T. Laflin

1999-08-01T23:59:59.000Z

471

Optimisation of buildings' solar irradiation availability  

SciTech Connect (OSTI)

In order to improve the sustainability of new and existing urban settlements it is desirable to maximise the utilisation of the solar energy incident on the building envelope, whether by passive or active means. To this end we have coupled a multi-objective optimisation algorithm with the backwards ray tracing program RADIANCE which itself uses a cumulative sky model for the computation of incident irradiation (W h/m{sup 2}) in a single simulation. The parameters to optimise are geometric (the height of buildings up to their facade and the height and orientation of roofs), but with the constraint of maintaining an overall built volume, and the objective function is heating season solar irradiation offset by envelope heat losses. This methodology has been applied to a range of urban typologies and produces readily interpretable results. The focus of this work is on the design of new urban forms but the method could equally be applied to examine the relative efficiency of existing urban settlements, by comparison of existing forms with the calculated optima derived from relevant specifications of the building envelope. (author)

Kaempf, Jerome Henri; Montavon, Marylene; Bunyesc, Josep; Robinson, Darren [Solar Energy and Building Physics Laboratory, Station 18, Ecole Polytechnique Federale de Lausanne, 1015 Lausanne (Switzerland); Bolliger, Raffaele [Industrial Energy Systems Laboratory, Station 9, Ecole Polytechnique Federale de Lausanne, 1015 Lausanne (Switzerland)

2010-04-15T23:59:59.000Z

472

LWRS ATR Irradiation Testing Readiness Status  

SciTech Connect (OSTI)

The Light Water Reactor Sustainability (LWRS) Program was established by the U.S. Department of Energy Office of Nuclear Energy (DOE-NE) to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current reactors. The LWRS Program is divided into four R&D Pathways: (1) Materials Aging and Degradation; (2) Advanced Light Water Reactor Nuclear Fuels; (3) Advanced Instrumentation, Information and Control Systems; and (4) Risk-Informed Safety Margin Characterization. This report describes an irradiation testing readiness analysis in preparation of LWRS experiments for irradiation testing at the Idaho National Laboratory (INL) Advanced Test Reactor (ATR) under Pathway (2). The focus of the Advanced LWR Nuclear Fuels Pathway is to improve the scientific knowledge basis for understanding and predicting fundamental performance of advanced nuclear fuel and cladding in nuclear power plants during both nominal and off-nominal conditions. This information will be applied in the design and development of high-performance, high burn-up fuels with improved safety, cladding integrity, and improved nuclear fuel cycle economics

Kristine Barrett

2012-09-01T23:59:59.000Z

473

Analysis of tritium transport in irradiated beryllium  

SciTech Connect (OSTI)

Analysis of the beryllium tritium release results with simple analytical models indicated that tritium behavior in Be is not dominated by one simple mechanism, but by a combination of several mechanisms including surface processes and helium bubbles. A model was developed and the initial version of the model included tritium diffusion in the beryllium and the beryllium oxide, second order desorption at the solid/gas interface and diffusion through interconnected porosity. Fundamental data, tritium diffusion and desorption coefficients for Be and BeO, were derived from experimental data using the model. Beryllium is a metal to which one can generally apply the concepts of diffusion, solubility, surface processes and traps. Tritium transport in the irradiated beryllium is affected by processes occurring in the bulk, He bubbles, the bulk/surface and surface/gas interfaces. There are two types of solid/gas surfaces in the irradiated Be. One is the surface at the pure Be/He bubble interface where no oxide layer exists and the other is the surface at the BeO layer/purge gas interface. Although the material characteristics of the Be and BeO layer are different and have different activation barriers, the surface processes can be applied to both interfaces.

Cho, S.; Abdou, M.A. [Univ. of California, Los Angeles, CA (United States)

1994-12-31T23:59:59.000Z

474

WHAT'S IN A NAME? GLOBAL WARMING VERSUS CLIMATE CHANGE  

E-Print Network [OSTI]

WHAT'S IN A NAME? GLOBAL WARMING VERSUS CLIMATE CHANGE May 2014 #12;What's In A Name? Global Warming vs. Climate Change 1 TABLE OF CONTENTS PREFACE NATIONAL SURVEY STUDY 2: GLOBAL WARMING VS. CLIMATE CHANGE............................ 10 Is global

Haller, Gary L.

475

Postharvest irradiation treatment effect on grapefruit functional components and their role in prevention of colon cancer  

E-Print Network [OSTI]

and irradiation significantly (P ? 0.05) affected the bioactive compounds in grapefruit, however, the effect of storage was prominent. The third study examined the influence of irradiation and freeze drying on bioactive compounds of grapefruit. Irradiation...

Vanamala, Jairam Krishna Prasad

2005-11-01T23:59:59.000Z

476

Solar Radiometric Data Quality Assessment of SIRS, SKYRAD and GNDRAD Measurements (Poster)  

SciTech Connect (OSTI)

Solar radiation is the driving force for the earth's weather and climate. Understanding the elements of this dynamic energy balance requires accurate measurements of broadband solar irradiance. Since the mid-1990's the ARM Program has deployed pyrheliometers and pyranometers for the measurement of direct normal irradiance (DNI), global horizontal irradiance (GHI), diffuse horizontal irradiance (DHI), and upwelling shortwave (US) radiation at permanent and mobile field research sites. This poster summarizes the basis for assessing the broadband solar radiation data available from the SIRS, SKYRAD, and GNDRAD measurement systems and provides examples of data inspections.

Habte, A.; Stoffel, T.; Reda, I.; Wilcox, S.; Kutchenreiter, M.; Gotseff, P.; Anderberg, M.

2014-03-01T23:59:59.000Z

477

Global Capitalism Theory and the Emergence of Transnational Elites  

E-Print Network [OSTI]

world economy associated with globalization have contributedGlobalization and the Post-Colonial World: The New Political Economy

Robinson, William I.

2010-01-01T23:59:59.000Z

478

Global Capitalism Theory and the Emergence of Transnational Elites  

E-Print Network [OSTI]

world economy associated with globalization have contributedGlobalization and the Post-Colonial World: The New Political Economy

Robinson, William I

2012-01-01T23:59:59.000Z

479

DOE Initiates Environmental Impact Statement for Global Nuclear...  

Office of Environmental Management (EM)

Environmental Impact Statement for Global Nuclear Energy Partnership Technology Demonstrations DOE Initiates Environmental Impact Statement for Global Nuclear Energy Partnership...

480

activities relating global: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

assessment in Azerbaijan Environmental Sciences and Ecology Websites Summary: , global warming, and global entrepreneurship. Discovery Park works syner- gistically with...

Note: This page contains sample records for the topic "global horizontal irradiance" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

assessing historical global: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

assessment in Azerbaijan Environmental Sciences and Ecology Websites Summary: , global warming, and global entrepreneurship. Discovery Park works syner- gistically with...

482

activation a global toggle: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

assessment in Azerbaijan Environmental Sciences and Ecology Websites Summary: , global warming, and global entrepreneurship. Discovery Park works syner- gistically with...

483

SHORT COMMUNICATION Microbeam irradiation of C. elegans nematode in microfluidic  

E-Print Network [OSTI]

SHORT COMMUNICATION Microbeam irradiation of C. elegans nematode in microfluidic channels M implemented a microfluidic tool for microbeam irradiation of Caenorhabditis elegans. The device allows into the microfluidic device through liquid flow between an inlet and an outlet, and the size of each microchannel

Brenner, David Jonathan

484

Retention of Hydrogen Isotopes in Neutron Irradiated Tungsten  

SciTech Connect (OSTI)

To investigate the effects of neutron irradiation on hydrogen isotope retention in tungsten, disk-type specimens of pure tungsten were irradiated in the High Flux Isotope Reactor in Oak Ridge National Laboratory followed by exposure to high flux deuterium (D) plasma in Idaho National Laboratory. The results obtained for low dose n-irradiated specimens (0.025 dpa for tungsten) are reviewed in this paper. Irradiation at coolant temperature of the reactor (around 50 degrees C) resulted in the formation of strong trapping sites for D atoms. The concentrations of D in n-irradiated specimens were ranging from 0.1 to 0.4 mol% after exposure to D plasma at 200 and 500 degrees C and significantly higher than those in non-irradiated specimens because of D-trapping by radiation defects. Deep penetration of D up to a depth of 50-100 µm was observed at 500 degrees C. Release of D in subsequent thermal desorption measurements continued up to 900 degrees C. These results were compared with the behaviour of D in ion-irradiated tungsten, and distinctive features of n-irradiation were discussed.

Yuji Hatano; Masashi Shimada; Yasuhisa Oya; Guoping Cao; Makoto Kobayashi; Masanori Hara; Brad J. Merrill; Kenji Okuno; Mikhail A. Sokolov; Yutai Katoh

2013-03-01T23:59:59.000Z

485

Irradiation effects in high-density polyethylene Jussi Polvia  

E-Print Network [OSTI]

Irradiation effects in high-density polyethylene Jussi Polvia , Kai Nordlunda a simulations, we have studied the irradiation effects in high density polyethylene. We determined the threshold energy for creating defects in the polyethylene lattice as a function of the incident angle. We found

Nordlund, Kai

486

Asymmetric Orientational Writing in glass with femtosecond laser irradiation  

E-Print Network [OSTI]

Asymmetric Orientational Writing in glass with femtosecond laser irradiation B. Poumellec,1 M in the dielectric inducing an asymmetric stress field is proposed. ©2013 Optical Society of America OCIS codes: (160. Prade, and A. Mysyrowicz, "Femtosecond laser irradiation stress induced in pure silica," Opt. Express 11

Boyer, Edmond

487

Physica B 308310 (2001) 612615 Irradiation effects in semiconducting diamonds  

E-Print Network [OSTI]

Physica B 308­310 (2001) 612­615 Irradiation effects in semiconducting diamonds N. Kristianpoller irradiation on semiconducting diamonds (type IIb) were studied and compared with those induced at the same conditions in natural (type Ia) and in synthetic diamonds. Methods of optical absorption, of X-ray and light

Chen, Reuven

488

SPECTRAL SOLAR IRRADIANCE AND ITS ENTROPIC EFFECT ON EARTH'S CLIMATE  

E-Print Network [OSTI]

SPECTRAL SOLAR IRRADIANCE AND ITS ENTROPIC EFFECT ON EARTH'S CLIMATE Wei Wu1 , Yangang Liu1 of the spectral solar irradiance (SSI) at the top of the Earth's atmosphere by the Solar Radiation and Climate's entropy flux from the TOA incident solar radiation. Two extreme cases are examined by using Planck

489

Improved Irradiation Performance of Uranium-Molybdenum/Aluminum Dispersion Fuel by Silicon Addition in Aluminum  

SciTech Connect (OSTI)

Uranium-molybdenum fuel particle dispersion in aluminum is a form of fuel under development for conversion of high-power research and test reactors from highly enriched to low-enriched uranium in the U.S. Global Threat Reduction Initiative program (also known as the Reduced Enrichment for Research and Test Reactors program). Extensive irradiation tests have been conducted to find a solution for problems caused by interaction layer growth and pore formation between U-Mo and Al. Adding a small amount of Si (up to [approximately]5 wt%) in the Al matrix was one of the proposed remedies. The effect of silicon addition in the Al matrix was examined using irradiation test results by comparing side-by-side samples with different Si additions. Interaction layer growth was progressively reduced with increasing Si addition to the matrix Al, up to 4.8 wt%. The Si addition also appeared to delay pore formation and growth between the U-Mo and Al.

Yeon Soo Kim; G. L. Hofman; A. B. Robinson; D. M. Wachs

2013-10-01T23:59:59.000Z

490

Standard Guide for Packaging Materials for Foods to Be Irradiated  

E-Print Network [OSTI]

1.1 This guide provides a format to assist producers and users of food packaging materials in selecting materials that have the desirable characteristics for their intended use and comply with applicable standards or government authorizations. It outlines parameters that should be considered when selecting food-contact packaging materials intended for use during irradiation of prepackaged foods and it examines the criteria for fitness for their use. 1.2 This guide identifies known regulations and regulatory frameworks worldwide pertaining to packaging materials for holding foods during irradiation; but it does not address all regulatory issues associated with the selection and use of packaging materials for foods to be irradiated. It is the responsibility of the user of this guide to determine the pertinent regulatory issues in each country where foods are to be irradiated and where irradiated foods are distributed. 1.3 This guide does not address all of the food safety issues associated with the synergisti...

American Society for Testing and Materials. Philadelphia

2009-01-01T23:59:59.000Z

491

Combustion Assisted Gravity Drainage (CAGD): An In-Situ Combustion Method to Recover Heavy Oil and Bitumen from Geologic Formations using a Horizontal Injector/Producer Pair  

E-Print Network [OSTI]

Combustion assisted gravity drainage (CAGD) is an integrated horizontal well air injection process for recovery and upgrading of heavy oil and bitumen from tar sands. Short-distance air injection and direct mobilized oil production are the main...

Rahnema, Hamid

2012-11-21T23:59:59.000Z

492

Cite as: Scott, S.D. & Carpendale, S. (2010). Theory of Tabletop Territoriality. In C. Mller-Tomfelde (ed.), Tabletops -Horizontal Interactive Displays, Springer  

E-Print Network [OSTI]

Cite as: Scott, S.D. & Carpendale, S. (2010). Theory of Tabletop Territoriality. In C. Müller-Tomfelde (ed.), Tabletops - Horizontal Interactive Displays, Springer (HCI Stacey D. Scott and Sheelagh Carpendale Abstract This chapter discusses empirical

DiMarco, Chrysanne

493

Horizontal well construction/completion process in a Gulf of Mexico unconsolidated sand: development of baseline correlations for improved drill-in fluid cleanup practices  

E-Print Network [OSTI]

This thesis examines, in detail, the procedures and practices undertaken in the drilling and completion phases of a Gulf of Mexico horizontal well in an unconsolidated sand. In particular, this thesis presents a detailed case history analysis...

Lacewell, Jason Lawrence

2012-06-07T23:59:59.000Z

494

Dartmouth Stellar Evolution Database and the ACS Survey of Galactic Globular Clusters II. Stellar Evolution Tracks, Isochrones, Luminosity Functions, and Synthetic Horizontal-Branch Models  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

Web tools are also available at the home page (http://stellar.dartmouth.edu/~models/index.html). These tools allow users to create isochrones and convert them to luminosity functions or create synthetic horizontal branch models.

Dotter, A; Chaboyer, B; Jevremovic, D; Kostov, V; Baron, E; Ferguson, J; Sarajedini, A; Anderson, J

495

Assessing Benefits in Vehicle Speed and Lateral Position when Chevrons with Full Retroreflective Sign Posts are Implemented on Rural Horizontal Curves  

E-Print Network [OSTI]

Driving a horizontal roadway curve requires a change in vehicle alignment and a potential reduction in speed. Curves may present a challenging situation during adverse conditions or to inattentive drivers. Chevron signs provide advanced warning...

Re, Jonathan M.

2010-01-16T23:59:59.000Z

496

E-Print Network 3.0 - accelerated partial-breast irradiation...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

irradiated for one hour... 1 Irradiation of Nd-Fe-B Permanent Magnets with APS Bending Magnet ... Source: Kemner, Ken - Biosciences Division, Argonne National Laboratory...

497

Global warming, insurance losses and financial industry  

SciTech Connect (OSTI)

Global warming causes extremely bad weather in the near term. They have already caught the attention of the insurance industry, as they suffered massive losses in the last decade. Twenty-one out of the 25 largest catastrophes in the US, mainly in the form of hurricanes have occurred in the last decade. The insurance industry has reacted by taking the risk of global warming in decisions as to pricing and underwriting decisions. But they have yet to take a more active role in regulating the factors that contributes to global warming. How global warming can impact the financial industry and the modern economy is explored. Insurance and modern financial derivatives are key to the efficient functioning of the modern economy, without which the global economy can still function but will take a giant step backward. Any risk as global warming that causes economic surprises will hamper the efficient working of the financial market and the modern economy.

Low, N.C. [UOB Life Assurance Limited, Singapore (Singapore)

1996-12-31T23:59:59.000Z

498

Instrumentation to Enhance Advanced Test Reactor Irradiations  

SciTech Connect (OSTI)

The Department of Energy (DOE) designated the Advanced Test Reactor (ATR) as a National Scientific User Facility (NSUF) in April 2007 to support U.S. leadership in nuclear science and technology. By attracting new research users - universities, laboratories, and industry - the ATR will support basic and applied nuclear research and development, further advancing the nation's energy security needs. A key component of the ATR NSUF effort is to prove new in-pile instrumentation techniques that are capable of providing real-time measurements of key parameters during irradiation. To address this need, an assessment of instrumentation available and under-development at other test reactors has been completed. Based on this review, recommendations are made with respect to what instrumentation is needed at the ATR and a strategy has been developed for obtaining these sensors. Progress toward implementing this strategy is reported in this document. It is anticipated that this report will be updated on an annual basis.

J. L. Rempe; D. L. Knudson; K. G. Condie; J. E. Daw; S. C. Taylor

2009-09-01T23:59:59.000Z

499

Irradiation behavior of metallic fast reactor fuels  

SciTech Connect (OSTI)

Metallic fuels were the first fuels chosen for liquid metal cooled fast reactors (LMR's). In the late 1960's world-wide interest turned toward ceramic LMR fuels before the full potential of metallic fuel was realized. However, during the 1970's the performance limitations of metallic fuel were resolved in order to achieve a high plant factor at the Argonne National Laboratory's Experimental Breeder Reactor II. The 1980's spawned renewed interest in metallic fuel when the Integral Fast Reactor (IFR) concept emerged at Argonne National Laboratory. A fuel performance demonstration program was put into place to obtain the data needed for the eventual licensing of metallic fuel. This paper will summarize the results of the irradiation program carried out since 1985.

Pahl, R.G.; Porter, D.L.; Crawford, D.C.; Walters, L.C.

1991-01-01T23:59:59.000Z

500

Optimization parameter design for proton irradiation accelerator  

E-Print Network [OSTI]

The proton irradiation accelerator is widely founded for industry application, and should be designed as compact, reliable, and easy operate. A 10 MeV proton beam is designed to be injected into the slow circulation ring with the repetition rate of 0.5 Hz for accumulation and acceleration, and then the beam with the energy of 300MeV will be slowly extracted by third order resonance method. For getting a higher intensity and more uniform beam, the height of the injection bump is carefully optimised during the injection period. Besides, in order to make the extracted beam with a more uniform distribution, a RF Knock-out method is adopted, and the RF kicker's amplitude is well optimised.

Yu-Wen An; Hong-Fei Ji; Sheng Wang; Shou-Yan Xu

2014-11-20T23:59:59.000Z