Powered by Deep Web Technologies
Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

EIA-23L Reserves Information Gathering System (RIGS)  

Gasoline and Diesel Fuel Update (EIA)

EIA-23L Reserves Information Gathering System (RIGS) EIA-23L Reserves Information Gathering System (RIGS) Released: April 16, 2013 Background The Form EIA-23L, "Annual Survey of Domestic Oil and Gas Reserves, " is used to collect data on reserves of crude oil, natural gas, and natural gas liquids. These data are used to develop national and regional estimates of proved reserves of domestic crude oil, natural gas, and natural gas liquids, and to facilitate national energy policy decisions. Reporting on the Form EIA-23L is mandatory. Reserves Information Gathering System The Form EIA-23L Reserves Information Gathering System (RIGS), provides respondents with an efficient and effective means for filing the form using a personal computer (PC). Hardware / Software Requirements The minimum hardware requirements needed to install and use RIGS are:

2

Comparing rig power transmission systems  

SciTech Connect

Installed power on drilling rigs has increased steadily since the inception of rotary drilling technology as a result of technical advances and the need to penetrate deeper horizons. Higher power levels for the pumps, rotary table and drawworks are also required for drilling deep wells within an economically reasonable period. Power initially available on a rig had been about 35 kW on average, whereas power values on modern rigs drilling ultra-deep wells are on the order of several thousand kW. The installed power values on modern drilling rigs, subdivided with respect to depth range, are shown. After safety, economic factors are of paramount importance to rig operators. Among these, which include low acquisition cost, long service life and ease of maintenance, a particularly decisive factor is high efficiency.

Gutsche, W.; Noevig, T.

1989-04-01T23:59:59.000Z

3

C:\Documents and Settings\jhr\My Documents\C_drive\RIGS\users 2013\rigs_usersApril2013.vp  

Gasoline and Diesel Fuel Update (EIA)

23 23 Reserves Information Gathering System (RIGS) User's Guide Version 2013 For Report Year 2012 Energy Information Administration U.S. Department of Energy April 2013 Form EIA-23 Reserves Information Gathering System (RIGS) User's Guide April 2013 EIA-23 Reserves Information Gathering System (RIGS) User's Guide Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Hardware / Software Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installing the RIGS Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Using the EIA-23 Reserves Information Gathering System (RIGS) System . . . . . . . . . . . . . . . . . 4 Initial Data Import from Last Year's RIGS Submission File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The RIGS Main Menu Screen.

4

Diverter/bop system and method for a bottom supported offshore drilling rig  

SciTech Connect

This patent describes a system adapted for alternative use as a diverter or a blowout preventer for a bottom supported drilling rig and adapted for positioning beneath a rotary table of the drilling rig, the system comprising: a fluid flow controller having a controller housing with a lower opening and an upper opening and a vertical flow path therebetween and an outlet passage provided in its housing wall, and at least two bases. A method is described for installing a system adapted for alternative connection as a diverter or a blowout preventer for a bottom supported drilling rig positioned beneath a rotary table of the drilling rig after structural casing has been set in a borehole. The method comprises: positioning a first telescoping spool having a lower end and an upper end below the rotary table, the first spool having a first base disposed at its upper end, the first base having a port disposed in its wall; aligning a fluid flow controller having a controller housing wall outlet passage and adapted for alternative use as a diverter or a blowout preventer so that the controller is substantially vertically aligned between a bore of the rotary table above and the structural casing below; and securing the fluid flow controller beneath the drilling rig rotary table.

Roche, J.R.; Alexander, G.G.

1987-03-03T23:59:59.000Z

5

ORISE: WeB-MEDIS System Allows Hospitals to Gather and Track...  

NLE Websites -- All DOE Office Websites (Extended Search)

WeB-MEDIS ORISE-developed system helps emergency responders and hospitals gather and track patient data during emergencies The Oak Ridge Institute for Science and Education...

6

Diverter bop system and method for a bottom supported offshore drilling rig  

SciTech Connect

A system and method for installing a fluid flow controller and telescoping spools beneath an offshore bottom supported drilling rig rotary table is disclosed. Upper and lower telescoping spools are provided for initially connecting a Diverter/BOP convertible fluid flow controller between structural casing in the well and a permanent housing beneath the drilling rig rotary table. Clamp means are provided for clamping the rig vent line to an opening in the housing wall of the fluid flow controller during drilling of the borehole through the structural casing in preparation for setting and cementing the conductor casing. In that mode, the system is adapted as a diverter system. After the well is drilled for the conductor casing and the conductor casing is cemented and cut off at its top, a mandrel is fitted at the top of the conductor casing to which the lower end of the lower spool may be connected. The system may be used in this configuration as a diverter system, or after removal of the vent line and connection of a kill line to the housing outlet, the system may be used as a low pressure blowout preventer system.

Roche, J. R.; Alexander, G. G.; Carbaugh, W. L.

1985-06-25T23:59:59.000Z

7

Remote multi-position information gathering system and method  

DOE Patents (OSTI)

A technique for gathering specific information from various remote locations, especially fluorimetric information characteristic of particular materials at the various locations is disclosed herein. This technique uses a single source of light disposed at still a different, central location and an overall optical network including an arrangement of optical fibers cooperating with the light source for directing individual light beams into the different information bearing locations. The incoming light beams result in corresponding displays of light, e.g., fluorescent light, containing the information to be obtained. The optical network cooperates with these light displays at the various locations for directing outgoing light beams containing the same information as their cooperating displays from these locations to the central location. Each of these outgoing beams is applied to a detection arrangement, e.g., a fluorescence spectroscope, for retrieving the information contained thereby.

Hirschfeld, Tomas B. (Livermore, CA)

1989-01-01T23:59:59.000Z

8

Department of Mechanical Engineering Spring 2010 Kenya Water Well Drill Rig Redesign of Engine Drive Train System & Support Tower  

E-Print Network (OSTI)

of Engine Drive Train System & Support Tower Overview The team was presented with the task of redesigning the engine drive train system and support structure for a water drill rig to be used in Kenya. The original engine drive train system was fabricated by a professional machinist and had many intricate components

Demirel, Melik C.

9

New depths with mobile rig  

SciTech Connect

Magee-Poole Drilling Company, a drilling contractor operating out of the south Texas drilling center of Alice, claims it operates the largest mobile drilling rig in the world. That is, it's the only wheel mounted portable rig that drills to 16,000 feet with 4 1/2-inch drill pipe - at least 3000 feet deeper than the previous mobile drilling rig ratings. The unit is designated the Ingersoll-Rand 1500 Series. What's more significant, according to co-owner Don Magee, is that the rig's portability gets the rotary table turning to the right sooner; it drills more footage per year. It rigs up in 1 1/2 days versus 3 to 4 days for a conventional skid type rig normally used at these depths. The unit's compact arrangement, with more components combined into single loads, makes possible its higher mobility. A conventional skid rig might require 25 to 30 truckloads to move the rig components, mud system, fuel and water tank, houses for utilities, storage and crew change, generators, and drill pipe. The new rig moves in anywhere from four to nine loads less. Further, the rig components weigh less without sacrificing durability.

Not Available

1982-03-01T23:59:59.000Z

10

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

12-i Chapter 12 Rigging Hardware CHAPTER 12 RIGGING HARDWARE This chapter provides requirements for rigging accessories used in hoisting and rigging - shackles, eyebolts, eye nuts, links, rings, swivels, wire-rope clips, turnbuckles, rigging hooks, and load-indicating devices and implements the requirements of ANSI/ASME B30.26, "Rigging Hardware" (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 12.1 GENERAL..................................................................................................................................12-1 12.1.1 Good and Bad Rigging Practices ...................................................................................12-1 12.2 RIGGING HOOKS.....................................................................................................................12-5

11

Electricity on the rig. Part 3 - New electric rig technology  

SciTech Connect

The use of an SCR-controlled power system on an offshore drilling rig has lead to an increased acceptance of high technology equipment. Such equipment increases drilling productivity, reduces maintenance, and improves reliability. Most new rigs now have AC squirrel cage motors, brushless AC generators, silicon controlled rectifiers, DC motors, and swtichgear and motor starters. Several opportunities for cost reductions in SCR systems, such as improving the power factor, are studied in this paper.

McNair, W.L.

1983-07-01T23:59:59.000Z

12

Focus on rotary drill rigs  

SciTech Connect

This article discusses the drill rig, focusing on the rotary drill rigs. There are two principal drilling methods - rotary and percussion. In certain situations, percussion drilling is the most practical method, but for most applications, rotary drilling using the rotary-tricone bit with either steel-toothed cones or carbide inserts, is the common and accepted drilling technique. There are four principal reasons for a rotary drill rig: to provide power to the rotary-tricone bit; to provide air to clean the hole; to provide a life-support system for the rotary-tricone bits; and, to provide a stable and efficient platform from which to drill the hole.

Schivley, G.P. Jr.

1987-06-01T23:59:59.000Z

13

Hoisting & Rigging Fundamentals  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting and Rigging Hoisting and Rigging Fundamentals for Riaaers and ODerators Pendant Control - Components TR244C, Rev. 5 December 2002 TR244C Rev . 5 TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii HOISTING AND RIGGING OBJECTIVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 WIRE ROPE SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SYNTHETIC WEBBING SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I O CHAINSLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 METAL MESH SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 SPREADER BEAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 RIGGING HARDWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14

Integrated system for gathering, processing, and reporting data relating to site contamination  

DOE Patents (OSTI)

An integrated screening system comprises an intrusive sampling subsystem, a field mobile laboratory subsystem, a computer assisted design/geographical information subsystem, and a telecommunication linkup subsystem, all integrated to provide synergistically improved data relating to the extent of site soil/groundwater contamination. According to the present invention, data samples related to the soil, groundwater or other contamination of the subsurface material are gathered and analyzed to measure contaminants. Based on the location of origin of the samples in three-dimensional space, the analyzed data are transmitted to a location display. The data from analyzing samples and the data from the locating the origin are managed to project the next probable sample location. The next probable sample location is then forwarded for use as a guide in the placement of ensuing sample location, whereby the number of samples needed to accurately characterize the site is minimized. 10 figs.

Long, D.D.; Goldberg, M.S.; Baker, L.A.

1997-11-11T23:59:59.000Z

15

Method and system for gathering a library of response patterns for sensor arrays  

DOE Patents (OSTI)

A method of gathering a library of response patterns for one or more sensor arrays used in the detection and identification of chemical components in a fluid includes the steps of feeding samples of fluid with time-spaced separation of known components to the sensor arrays arranged in parallel or series configurations. Modifying elements such as heating filaments of differing materials operated at differing temperatures are included in the configurations to duplicate operational modes designed into the portable detection systems with which the calibrated sensor arrays are to be used. The response patterns from the known components are collected into a library held in the memory of a microprocessor for comparison with the response patterns of unknown components.

Zaromb, Solomon (Hinsdale, IL)

1992-01-01T23:59:59.000Z

16

Oil-spill aftermath hampers rig research  

Science Journals Connector (OSTI)

... Mexico, scientists say that they have been struggling to gain access to the region's rigs and drill ships, hampering their research. Marine scientists have long been allowed to install ... ships, hampering their research. Marine scientists have long been allowed to install instruments on offshore structures. The equipment can deliver vital data that would not be practical to gather ...

Melissa Gaskill

2011-07-04T23:59:59.000Z

17

Experimental analysis of control loops with different delay times in the supply air system of a radiator test rig  

Science Journals Connector (OSTI)

The test rig of low-temperature hot-water radiator is a typical multi-input multi-output (MIMO) thermal system with large time delay. Aiming at the control of the supply air temperature and the temperature of the environmental chamber in the test rig, the paper carries out the fuzzy control experiments and PI control experiments based on adjusting the electric heater in the supply air system, in which there are two control loops with various delay time. The experiments researched two types of fuzzy control methods which are the basic fuzzy control (BFC), and the self-organizing rules fuzzy control (SORFC) with zero initial control rules. For the control loop of supply air temperature with short delay time, PI control performs better with fast convergence speed and small overshoot than the BFC and the SORFC. The convergence speed of the BFC method is lower than other two control methods. For the control loop of chamber temperature with long delay time, the SORFC has a satisfied control performance with less overshoot and stable error than the BFC and PI control.

Yongpan Chen; Jili Zhang; Zhen Lu; Tianyi Zhao; Hui Liu

2011-01-01T23:59:59.000Z

18

Hoisting & Rigging Assessment Form  

Energy.gov (U.S. Department of Energy (DOE))

  Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices...

19

Four rigs refurbished for West Africa drilling  

SciTech Connect

In April and May 1990, Shell Petroleum Development Co. of Nigeria Ltd. awarded Noble Drilling West Africa Inc. four separate contracts to drill oil and gas wells in the inland waterways of Nigeria. The contracted rigs included a shallow water jack up, the NN-1, and three posted barges, the Gene Rosser, the Chuck Syring, and the Lewis Dugger. The jack up was built in 1978, and the three posted barges are 1980s vintage. Three of the rigs have been idle for a number of years. The Shell Nigeria contracts required major modifications to the rigs before putting them into international service. Noble replaced or refurbished all major pieces of equipment in the drilling, power, and service systems on the rigs. Rig crews serviced all other equipment. A significant amount of general service piping and electrical wiring was replaced. Each rig also required additional motor control centers to support the new drilling and mud processing equipment. Alfa-Laval waste-heat water desalination plants and new sewage treatment units were installed on all four rigs. Because of the tidal variances and high silt conditions expected in the African waterways, all engine cooling systems were converted from heat exchangers to radiators. Rotary tables were made common on all rigs at 37 1/2 in. Noble had all traveling equipment completely inspected and modified as necessary. Strict attention was paid to certification and documentation of all equipment. Safety upgrades conformed to both Shell and Noble standards. Fire and gas detection systems were installed throughout each rig. Water and foam deluge systems were installed in the wellhead areas, and new foam systems and monitors were installed on the helldecks.

Not Available

1991-06-10T23:59:59.000Z

20

Chapter 10 - RIGGING HARDWARE  

NLE Websites -- All DOE Office Websites (Extended Search)

ASME, DOERL-92-36 and the Rigging Hardware manufacturers' requirements. It is the responsibility of the user of this manual to implement all of the requirements from listed...

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

International land rig locator  

SciTech Connect

Mechanical specifications, ratings, locations, and status are listed for each of the 5,000 contract rotary drilling rigs operated by the more than 700 independent drilling contractors throughout the Free World.

Not Available

1984-03-01T23:59:59.000Z

22

International land rig locator  

SciTech Connect

Mechanical specifications, ratings, locations, and status are listed for each of the 5,000 contract rotary drilling rigs operated by more than 700 independent drilling contractors throughout the Free World.

Not Available

1983-09-01T23:59:59.000Z

23

Rig Efficiency Paper  

Annual Energy Outlook 2012 (EIA)

"active" annual rig count which is an imprecise and subjective task. Baker Hughes, 5 Smith, 6 ReedHycalog (Now NOV), 7 Schlumberger, 8 and IADC 9 publicly report the number of...

24

Electricity on the rig; part I -- electric applications on drilling and workover rigs  

SciTech Connect

This article points out that not only have electric motors replaced diesel engines and mechanical transmissions, but solid-state equipment is rapidly taking the place of rotary equipment in variable speed drivers and control systems. The SCR (silicon controlled rectifier) type of speed control has replaced other types by a large margin of acceptance on drilling rigs and has begun to be used on workover and service rigs. In most cases, electrical power is generated at the rig site with diesel-AC generators. On mechanically driven rigs, single diesel-generator sets operate to supply power for lighting and electrical motor loads. When high levels of power are required, such as on SCR-powered rigs, multiple generators are operated in electrical-parallel and each contributes to the total power required.

McNair, W.L.

1983-03-01T23:59:59.000Z

25

The Feasibility of Natural Gas as a Fuel Source for Modern Land-Based Drilling Rigs  

E-Print Network (OSTI)

rigs are still in use today, most modern drilling rigs are electrically powered. Electric drilling rig engines are coupled to electric generators, in what is called a generator set, or genset, which creates electricity that powers electric motors... drilling rigs can be categorized into either direct current (DC) or alternating current (AC), depending on the type of electricity the rig generators produce. Electric motors power the draw-works, top drive, mud pumps, and other systems with electricity...

Nunn, Andrew Howard

2012-02-14T23:59:59.000Z

26

Loads on Tie-Down Systems for Floating Drilling Rigs during Hurricane Conditions  

E-Print Network (OSTI)

and SPAR Motion The motion characteristics of TLP and SPAR in the ocean are quite different due to the geometric shape of each structure and mooring configurations. These differences cause the different loading on tie-down systems. To some extent... by integrating the boundary element of submerged structures of interest or by the geometry itself in frequency domain. The external stiffness due to tendon and riser should be also considered to ensure a more reliable result. All of these procedures...

Bae, Yoon Hyeok

2010-01-16T23:59:59.000Z

27

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE-STD-1090-2011 DOE-STD-1090-2011 September 2011 Superseding DOE-STD-1090-2007 August 2007 DOE STANDARD HOISTING AND RIGGING U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND INTENTIONALLY BLANK DOE-STD-1090-2011 iii Introduction The U.S. Department of Energy (DOE) Hoisting and Rigging Standard is intended to be used by supervisors, line managers, safety personnel, equipment operators, riggers and other personnel responsible for the safety of hoisting and rigging operations at DOE sites. It may be used as either contract document or as a best practices guide at the site's or program office's discretion. The standard invokes applicable OSHA and national consensus standards but also delineates

28

MHK Technologies/Ocean Energy Rig | Open Energy Information  

Open Energy Info (EERE)

Rig Rig < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Ocean Energy Rig.jpg Technology Profile Primary Organization Free Flow 69 Technology Resource Click here Current Technology Type Click here Axial Flow Turbine Technology Readiness Level Click here TRL 4 Proof of Concept Technology Description The Ocean Energy Rig is a hybrid concept harnessing tidal stream with increased velocity from venturi system wave and wind power The rig also uses solar panels to power computers and warning lights Other unique features include a water ballasting system with automatic self levelling and wave ramps to maximize FreeFlow 69 s new wave power device It is envisaged that the Ocean Energy Rig would be assembled and maintained in dry docks and would be towed out into position before being semi submerged and anchored for operation Power output of the production model would be at least 10MW

29

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

13-i CHAPTER 13 LOAD HOOKS This chapter provides safety standards for the inspection, testing, and maintenance of load hooks installed on cranes or hoists and implements the requirements of ASME B30.10, Chapter 10-1, "Hooks." See Chapter 12, "Rigging Accessories," for rigging hook requirements (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 13.1 GENERAL ...............................................................................................................................13-1 13.1.1 Marking......................................................................................................................13-1 13.1.2 Attachments ...............................................................................................................13-1

30

Gathering knowledge for a question answering system from heterogeneous information sources  

Science Journals Connector (OSTI)

Although vast amounts of information are available electronically today, no effective information access mechanism exists to provide humans with convenient information access. A general, open-domain question answering system is a solution to this problem. ...

Boris Katz; Jimmy Lin; Sue Felshin

2001-07-01T23:59:59.000Z

31

Design of a bicycle rig  

E-Print Network (OSTI)

A design of a bicycle (bike) rig was conducted. This bike rig is designed to be used for aerodynamics measurement testing of bicycles, cyclists and cycling related items in a wind tunnel. This paper discusses the design ...

Racz, Rastislav

2010-01-01T23:59:59.000Z

32

Workover well control. Part 3. Conventional rigs, snubbing units handle a variety of workover jobs  

SciTech Connect

The conventional rig, the most widely used rig for workovers, performs several common functions: tripping in and out of the hole, rotating the work string, and circulating fluid. Its primary component groups are the derrick, hoisting systems, rotary tools, circulating systems, and tubular goods. Rig sizing depends on the job requirements; the typical workover rig is a small-capacity, single unit used for concentric work. A workover rig's most important feature is its portability; compartmentalizing the rig permits transporting it offshore in packages smaller than 8000 lb and allows small cranes to replace derrick barges for loading operations.

Adams, N.

1981-08-31T23:59:59.000Z

33

44. Annual Reed rig census  

SciTech Connect

Reed Tool Company`s 44th annual rotary rig census found a spirit of increased optimism in the US oil and gas drilling industry. Rig utilization rose to 77% this year, the highest since the boom times of 15 years ago. A combination of a higher number of active rigs and another decline in available units to a historical low, led to this higher-than-average utilization rate. The paper discusses results from the survey.

Stokes, T.A.; Rodriguez, M.R. [Reed Tool Co., Houston, TX (United States)

1996-10-01T23:59:59.000Z

34

Hoisting & Rigging Assessment Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING HOISTING & RIGGING Assessment Plan NNSA/Nevada Site Office Facility Representative Division Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging

35

Hoisting & Rigging Assessment Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING HOISTING & RIGGING Assessment Plan NNSA/Nevada Site Office Facility Representative Division Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging

36

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1-i 1-i CHAPTER 11 WIRE ROPE AND SLINGS This chapter provides requirements for the fabrication and use of wire rope and slings used in hoisting and rigging and implements the requirements of ASME B30.9, Slings (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). . 11.1 GENERAL ...............................................................................................................................11-1 11.2 WIRE ROPE ............................................................................................................................11-4 11.2.1 Wire-Rope Lays .........................................................................................................11-4 11.2.2 Wire-Rope Cores .......................................................................................................11-4

37

Advanced Hot Section Materials and Coatings Test Rig  

SciTech Connect

Phase I of the Hyperbaric Advanced Hot Section Materials & Coating Test Rig Program has been successfully completed. Florida Turbine Technologies has designed and planned the implementation of a laboratory rig capable of simulating the hot gas path conditions of coal gas fired industrial gas turbine engines. Potential uses of this rig include investigations into environmental attack of turbine materials and coatings exposed to syngas, erosion, and thermal-mechanical fatigue. The principle activities during Phase 1 of this project included providing several conceptual designs for the test section, evaluating various syngas-fueled rig combustor concepts, comparing the various test section concepts and then selecting a configuration for detail design. Conceptual definition and requirements of auxiliary systems and facilities were also prepared. Implementation planning also progressed, with schedules prepared and future project milestones defined. The results of these tasks continue to show rig feasibility, both technically and economically.

Dan Davis

2006-09-30T23:59:59.000Z

38

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 BELOW-THE-HOOK LIFTING DEVICES 14-i This chapter provides the requirements for below-the-hook lifting devices used in hoisting and rigging, such as spreader bars, lifting yokes, and lift fixtures. This section implements the requirements of ASME B30.20, "Below-the-Hook Lifting Devices" (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). NOTE: Special lifting devices for shipping containers weighing 10,000 lb or more that are used for radioactive materials are governed by ANSI N14.6 ["Standard for Special Lifting Devices for Shipping Containers Weighing 10,000 Pounds (4,500 kg) or More for Nuclear Materials."] 14.1 GENERAL ...............................................................................................................................14-1

39

Innovative Techniques of Multiphase Flow in Pipeline System for Oil?Gas Gathering and Transportation with Energy?Saving and Emission?Reduction  

Science Journals Connector (OSTI)

Multiphase flow measurement desanding dehumidification and heat furnace are critical techniques for the oil and gas gathering and transportation which influnce intensively the energy?saving and emission?reduction in the petroleum industry. Some innovative techniques were developed for the first time by the present research team including an online recognation instrument of multiphase flow regime a water fraction instrument for multuphase flow a coiled tube desanding separator with low pressure loss and high efficiency a supersonic swirling natural gas dehumifier and a vacuum phase?change boiler. With an integration of the above techniques a new oil gas gathering and transpotation system was proposed which reduced the establishment of one metering station and several transfer stations compared with the tranditional system. The oil and gas mixture transpotation in single pipes was realized. The improved techniques were applied in the oilfields in China and promoted the productivity of the oilfields by low energy consumption low emissions high efficiency and great security.

Bofeng Bai; Liejin Guo; Shaojun Zhang; Ximin Zhang; Hanyang Gu

2010-01-01T23:59:59.000Z

40

Solar stirling engine rig tests  

Science Journals Connector (OSTI)

A description of a prototype four-cylinder Stirli ng engine construction with the heat receiver of the concentrated solar radiant flux and with a swashplate drive is given. The rig tests have been carried out ...

I. A. Tursunbaev; E. P. Orda; A. I. Lezhebokov; A. P. Korobkov…

2010-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Earth drill rig  

SciTech Connect

This patent describes an earth drill rig wherein an upwardly and downwardly moving drill-string-turning rotary table is rotated by a kelly bar connected at its lower end to a vertical drive shaft, the kelly bar being journalled for rotation in and fixed against axial movement with respect to a drill frame assembly and the rotary table being mounted for axial movement on and along the drill frame assembly. The drill frame assembly is pivotally mounted on a vehicle on a substantially horizontal axis for pivoting between an upright position and a substantially horizontal position for transportation. The improvement described here comprises the drill frame assembly pivot axis positioned below the lower end of the kelly bar and above the upper end of the vertical drive shaft, and a universal coupling connecting the lower end of the kelly bar and the vertical drive shaft the universal coupling comprising universal joints at opposite ends of an elongated slip joint connector and connected there-by for relative axial movement but driving coupling between the universal joints. The universal joints lie generally on a circle of which the drill frame assembly pivot axis is the center. The drill frame assembly can be moved between the upright and the substantially horizontal positions without disconnecting the kelly bar from the vertical drive shaft, the kelly bar being revolvable by the drive shaft through substantially the entire range of movement of the drill frame assembly.

Rassieur, C.L.

1987-01-27T23:59:59.000Z

42

Drill rig hook  

SciTech Connect

A hook for suspending a pipe string or other load in a well rig, including a tubular outer body supported by a first connector structure which is attachable to a suspending line, a tubular inner body which supports a second connector structure preferably taking the form of a hook, with the inner body being received within the outer body and being yieldingly urged upwardly relative thereto by a resilient unit or assembly located within the inner body, and with a structure within the inner body bearing upwardly against and supporting the resilient assembly and attached to the first connector structure. A cam mechanism between the inner and outer bodies automatically cams the inner body to a predetermined rotary position upon upward movement, with a locking device or devices serving to retain the inner body in fixed rotary position and/or to lock the camming mechanism in a fixed position in a manner determining the rotary setting to which the inner body returns upon upward movement. The mentioned first and/or second connectors may each consist of two parts receivable within one of the tubular bodies and held in operative connecting engagement therewith by a spacer between the two parts. A link suporting member may be formed separately from the load suporting hook, to be detachable therefrom for a repair or replacement.

Zimmermann, A.

1985-02-12T23:59:59.000Z

43

Gathering asynchronous mobile robots with inaccurate compasses  

Science Journals Connector (OSTI)

This paper considers a system of asynchronous autonomous mobile robots that can move freely in a two-dimensional plane with no agreement on a common coordinate system. Starting from any initial configuration, the robots are required to eventually gather ...

Samia Souissi; Xavier Défago; Masafumi Yamashita

2006-12-01T23:59:59.000Z

44

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9-2004 9-2004 12-i Chapter 12 Rigging Accessories CHAPTER 12 RIGGING ACCESSORIES This chapter provides requirements for rigging accessories used in hoisting and rigging - shackles, eyebolts, rings, wire-rope clips, turnbuckles, rigging hooks, and load-indicating devices. 12.1 GENERAL ...............................................................................................................................12-1 12.1.1 Inspections .................................................................................................................12-1 12.1.2 Testing .....................................................................................................................12-3 12.1.3 Good and Bad Rigging Practices ...............................................................................12-3

45

34th annual reed rotary rig census  

SciTech Connect

This article reports that the number of rigs active according to the 1986 census is 1052, which represents a decline of 1573 rigs from 1985 figures. This 60 percent decrease is the largest decline of active rigs in the 34-year history of the census. The 1986 census takers found 3993 rigs are available with the capacity to drill deeper than 3000 ft. The count has thus declined by 416 rigs (9 percent) from the 1985 total of 4409. Rig availability declined for the fourth consecutive year following nine straight years of fleet expansion (1974-1982). During the past four years, 1651 rigs have been removed from the drilling fleet representing a 29 percent decline from the record high number of rigs available in 1982. The 1986 decline in the available U.S. fleet is considerably less than what many industry observers had been anticipating. A larger decrease in the rig fleet has not been realized for a number of reasons.

Hutchinson, D.L.; Pastusek, P.E.

1986-10-01T23:59:59.000Z

46

45th annual Reed rig census  

SciTech Connect

Since 1983, Reed Tool Co.`s annual rotary rig census has reported 14 consecutive annual reductions in the U.S. rig fleet. This year, the downward trend has reversed and more rigs have been added to the available fleet than have left. Robust drilling activity has also spurred higher rig utilization in 1997. Utilization climbed to 86.9% this year, more than ten percentage points higher than a year ago and the highest since 1981. Data and trends are discussed.

Stokes, T.A.; Rodriguez, M.R. [Reed Tool Co., Houston, TX (United States)

1997-10-01T23:59:59.000Z

47

Hoisting and Rigging Technical Advisory Committee  

Energy.gov (U.S. Department of Energy (DOE))

The Hoisting and Rigging Technical Advisory Committee serves as an advisory body to the Office of Health, Safety and Security (HSS) by providing support to their policy efforts aimed at ensuring the safe performance of hoisting and rigging activities at DOE facilities and in the review and resolution of identified generic hoisting and rigging safety issues.

48

36th annual Reed rig census  

SciTech Connect

For the sixth straight year, the number of rigs available in the U.S. declined. Five hundred and seventy-nine rotary rigs dropped out of drilling industry competition during the past 12 months as attrition forced rig supply closer toward balance with demand. Significant highlights of this year's census are: The U.S. rig fleet now stands at 2,752 drilling rigs, a 17.4% reduction from the census count in 1987. This is the largest percentage decline and the third largest absolute decline in available rigs in census history; The 1988 census active count was 1,532 rigs, up 10% over 1987; The 1988 census utilization rate was 55.7%, up from the 41.7% reported last year and a 110% improvement over the all-time low of 26.3% in 1986; Every region in the country reported a reduction in total available rigs. Each region also reported an increase in the active ring count with the exception of Ark-La-Tex; California had the highest utilization rate in the census (63.9%), and all regions reported a utilization rate greater than 50% with the exception of Ark-La-Tex, which reported a 45.5% rate; The number of rig owners declined 12% from 691 to 608. The decline in available rigs would have been greater, but owners brought back 226 rigs that had been dropped from previous census tabulations.

Fitts, R.L.; Crowhurst, M.E. (Reed Tool Co., Houston, TX (US))

1988-10-01T23:59:59.000Z

49

Hoisting & Rigging Lift Plan  

NLE Websites -- All DOE Office Websites (Extended Search)

Hoisting & Rigging Lift Plan Hoisting & Rigging Lift Plan Stanford Synchrotron Radiation Laboratory May 16, 2005 SSRL-HRLP-000-R0 Page 1 of 3 General Information Lift Plan Document # Plan prepared by: Describe the load or items to be lifted: Could the load, if dropped, release hazardous materials or radioactivity? No Yes (describe) Is the load irreplaceable or would it be very costly to replace if damaged? No Yes (describe) Brief description of lift activities (specify if rolling or flipping involved) Equipment Information Equipment ID: Equipment custodian: Rated capacity: Operator capacity : Personnel Protective Equipment (PPE) Steel-toed shoes Required for all personnel involved with lift activity to protect from crushing of feet/toes

50

Risk analysis of jackup rigs  

Science Journals Connector (OSTI)

Increasing attention has been focussed in the North Sea and elsewhere on the quantification of the risks of working in a hazardous enviroment: the offshore world. The perception of risk with respect to mobile rigs has often been vague and uninformed. This paper attempts to put the risks with respect to jackup rigs into perspective by quantifying them and comparing them to other risks. This paper contains a few risk comparisons with fixed platforms, semi-submersibles, and drillships. Historical casualties are used in an example to show how a change intended to make an operation safer, may result in the opposite effect. Examining risks from losses due to environmental overload, the conclusion is reached that jackups are very safe structures: there appears to be no jackup, in the timeframe examined, that has been lost because of a deficiency in the calculation methods currently in use by knowledgeable experts.

B.P.M. Sharples; W.T. Bennett Jr; J.C. Trickey

1989-01-01T23:59:59.000Z

51

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 HOISTS 8-i This chapter provides safety standards for inspecting, testing, and operating hoists not permanently mounted on overhead cranes and implements the requirements of ASME B30.11 ("Monorail Systems and Underhung Cranes"), B30.16["Overhead Hoists (Underhung)"], and B30.21 ("Manually Lever Operated Hoists") (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 8.1 GENERAL .................................................................................................................................8-1 8.1.1 Operator Training/Qualification ..................................................................................8-4 8.1.2 Marking........................................................................................................................8-4

52

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 OVERHEAD AND GANTRY CRANES 7-i This chapter specifies operation, inspection, maintenance, and testing requirements for the use of overhead and gantry cranes and implements the requirements of ASME B30.2 ["Overhead and Gantry Cranes (Top- Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist)"], B30.11 ("Monorail Systems and Underhung Cranes"), and B30.17 ["Overhead and Gantry Cranes (Top-Running Bridge, Single Girder, Underhung Hoist")] (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 7.1 GENERAL .................................................................................................................................7-1 7.1.1 Operator Training/Qualification

53

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 LIFTING PERSONNEL 4-i Chapter 4 Lifting Personnel This chapter specifies the design and inspection requirements for personnel lift platforms as well as the operational requirements for such platforms and appurtenant hoisting equipment. It implements the requirements of ASME B30.23, Personnel Lifting Systems (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 4.1 GENERAL ................................................................................................................................4-1 4.1.1 Personnel Lifting Evaluation .......................................................................................4-1 4.1.2 Designated Leader .......................................................................................................4-1

54

42nd Annual Reed rig census  

SciTech Connect

The eleven-year trend of attrition in the US rig fleet slowed significantly this year as only 12 rigs, or less than 1%, left the available fleet. The number of rotary rigs available for drilling in the US now stands at 1,841. but for the 42-year history of the Reed Tool Co. Rotary Rig Census, the 1973 available rig count of 1,767 remains the record low for yet another year. The count of rigs active during the 45-day census period also declined since last year's census. The active count was down 4.5% to 1,221 from 1,279 in 1993. As a consequence, rig utilization fell to 66.3% in 1994, from 69.0% last year. Notably, a strong shift to gas from oil drilling has occurred. Of the 1,221 rigs active in the census period, 540 were drilling for gas on the last well vs. 356 drilling for oil. Compared to last year, this is an increase in gas drilling of 29% and a decrease in oil drilling 22%. (Rigs targeting both oil and gas totaled 325 in 1994.)

Stokes, T.A.; Rodriquez, M.R. (Reed Tool Co., Houston, TX (United States))

1994-10-01T23:59:59.000Z

55

New ultra-deepwater rig with dual rotaries will reduce costs  

SciTech Connect

The Discoverer Enterprise, a next generation, ultra-deepwater drill ship with a dual rotary system, will decrease drilling and completion costs by reducing bottom hole assembly (BHA) and tubular preparation time. Transocean Offshore received a contract from Amoco Corp. to build the ultra-deep floating rig and is scheduled to spud its first well in July 1998. It will generally work in water deeper than 6,000 ft. The rig design involves a new approach that addresses the overall well-construction process and equipment required to decrease significantly deepwater drilling time. The Discoverer is the first ultra-deepwater rig designed specifically for handling subsea completions and extended well tests. The paper discusses increased deepwater rig demand, rig construction costs, drillship design, well construction, development drilling, and cost justification.

Cole, J.C.; Herrmann, R.P.; Scott, R.J. [Transocean Offshore Inc., Houston, TX (United States); Shaughnessy, J.M. [Amoco Corp., Houston, TX (United States)

1997-05-26T23:59:59.000Z

56

40th annual Reed rig census  

SciTech Connect

This paper reports that declines characterize the 1992 rig census-in the number of available drilling rigs, in the number of active rigs, in rig utilization rate, in the number of rig owners and in industry optimism. The number of rotary rigs available for U.S. drilling fell by 255 units (11.3%) during the past 12 months, an attrition rate almost four times greater than in 1991. But despite the high attrition, only 59.7% of remaining rigs were working during the time the census was taken. Results of the 1992 census bring emphasis to an industry trend that became apparent in early 1991. The major oil companies, and many independents, continued their exodus form the U.S., and the remaining independents, which were hurt by low natural gas prices and unfavorable tax treatment of intangible drilling costs, were not able to pick u the drilling slack. Consequently, the past year has been disastrous for many U.S. drilling contractors, and the outlook for this industry segment remains bleak.

Fitts, R.L.; Stokes, T.A. (Reed Tool Co., Houston, TX (United States))

1992-10-01T23:59:59.000Z

57

Fuzzy control model and simulation of supply air system in a test rig of low-temperature hot-water radiator system  

Science Journals Connector (OSTI)

This paper proposes a typical multi-variable, large time delay and nonlinear system, self-extracting rules fuzzy control (SERFC) method to maintain a stable temperature value in a built environment chamber with supply air system and hot-water system. The parameters of the transfer functions in every control loop were identified by experimental data in a format of time sequences obtained from the experiment of dynamical responding performance. Fuzzy control simulations were implemented based on adjustment of the supply air system and hot-water system by SERFC. The simulation results show that SERFC for environment chamber has satisfied performance. There is no higher overshoot and stable error. The work presented in here can be used to deal with those complex thermal processes with difficulties in modeling of fuzzy control rules and provide a foundation for further application of fuzzy control in HVAC system.

Zhen Lu; Jili Zhang; Yongpan Chen; Tianyi Zhao; Hui Liu

2010-01-01T23:59:59.000Z

58

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 CONSTRUCTION HOISTING AND RIGGING EQUIPMENT REQUIREMENTS 15-i Chapter 15 Construction Hoisting and Rigging Equipment Requirements This chapter outlines the requirements for the safe use of hoisting and rigging equipment on construction projects at DOE installations. 15.1 GENERAL ...............................................................................................................................15-1 15.2 PERSONNEL QUALIFICATIONS.........................................................................................15-2 15.2.1 Qualified Operators of Mobile Cranes.......................................................................15-2 15.2.2 Qualified Operators of Forklift Trucks ......................................................................15-3

59

Design Principles of a flywheel Regenerative Braking System (f-RBS) for Formula SAE type racecar and system testing on a Virtual Test Rig modeled on MSC ADAMS  

E-Print Network (OSTI)

momentum in the industry [4]. These vehicles (BEVs and HEVS) use electric motor/generator pairs to propel themselves and to recapture braking energy (electric RBS) and the power source is the battery. The regenerative braking system uses a generator..., aerodynamic and road losses. 4. Improvised Transmission design to reduce losses. 5. Hybrid and Alternative Energy Propulsion systems e.g. the Hybrid Electric Vehicle (HEV), the Fuel Cell Vehicle (FCV). 6. Recycling Braking energy – Storage and reuse...

Pochiraju, Anirudh

2012-08-31T23:59:59.000Z

60

39th annual Reed rig census  

SciTech Connect

This paper reports on cutbacks in U.S. exploration and development drilling during the first half of 1991 which squeezed most of the optimism out of the drilling industry. Just how rough the year has been is underscored by the results of this year's rig census. The number of rotary rigs available for U.S. drilling declined by only 69 units (3%) during the past 12 months. But despite those withdrawals from competition, only 66% of the remaining rigs were working at the time the census was taken. Results of the 1991 census contrasted sharply with the stability and optimism that seemed apparent a year ago when 72% of the available rig fleet met the census definition of active. At that time, the mini-boom in horizontal drilling coupled with tax-credit- driven gas drilling led to a relatively high rig utilization rate and suggested that rig supply and demand might be close to an economically acceptable balance. However, it quickly became apparent in early 1991 that industry optimism was unjustified. Horizontal drilling began to drop and the lowest natural gas prices in 12 years triggered rapid declines in gas drilling. Although oil prices have been relatively stable and above $18 per bbl since January 1989, most major operators have concluded that a better return on investment can be had outside the U.S. and have drastically cut their domestic drilling budgets. These factors, combined with softened energy demand from the worldwide recession, further slowed U.S. drilling. The long awaited balance between rig supply and demand has seemingly slipped away. The 1991 Reed rig census describes an industry facing several more rough years. Details of this year's census include: The available U.S. fleet now stands at 2,251 rigs, down by 69 from the 2,320-unit total in 1990, and the lowest since 1976. Rigs meeting the census definition of active numbered 1,485, down 192 (11.4%) from the 1,677 active rigs counted a year earlier.

Crowhurst, M.E.; Fitts, R.L. (Reed Tool Co., Houston, TX (US))

1991-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Group Based Rigging of Realistically Feathered Wings  

E-Print Network (OSTI)

for feather interpenetration resulting from movement from extended to folded wing poses [Hiebert 3 et al. 2006]. The rigging method developed for this thesis provides a single rig and control solution for animation that includes both outstretched... be highly detailed and as anatomically accurate as a mythical creature can be. A big challenge to this was the look and actions of the feathers [Hiebert et al. 2006]. The feathers on the gryphons (coverts, and body feathers) were generated procedurally...

Howard, Heather Vernette

2012-02-14T23:59:59.000Z

62

Department of Energy Supercomputer Helps Design More Efficient Big Rigs |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department of Energy Supercomputer Helps Design More Efficient Big Department of Energy Supercomputer Helps Design More Efficient Big Rigs Department of Energy Supercomputer Helps Design More Efficient Big Rigs February 8, 2011 - 12:00am Addthis Washington, DC - BMI Corporation, a company in South Carolina, in partnership with the Department of Energy's Oak Ridge National Laboratory (ORNL) has successfully developed a technology that will make semi trucks more fuel efficient with the potential to save millions of gallons of fuel. Utilizing the nation's most powerful computer, BMI Corp designed a SmartTruck UnderTray System, a set of integrated aerodynamic fairings that improve the aerodynamics of 18-wheeler (Class 8) long-haul trucks. If all 1.3 million Class 8 trucks in the U.S. were configured with these components, companies could achieve annual savings of 1.5 billion gallons

63

Gathering few fat mobile robots in the plane  

Science Journals Connector (OSTI)

Autonomous identical robots represented by unit discs move deterministically in the plane. They do not have any common coordinate system, do not communicate, do not have memory of the past and are totally asynchronous. Gathering such robots means forming ...

Jurek Czyzowicz; Leszek G?sieniec; Andrzej Pelc

2006-12-01T23:59:59.000Z

64

Odessa fabricator builds rig specifically for geothermal drilling  

Energy.gov (U.S. Department of Energy (DOE))

For 35 years, MD Cowan has built drilling rigs, developing a market for its Super Single® rig for use in the nation's oil and gas fields. Now the Odessa-based company is branching out into alternative energy.

65

DOE-STD-1090-99; DOE Standard Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

NLE Websites -- All DOE Office Websites (Extended Search)

TS TS INCH-POUND DOE-STD-1090-99 March 1999 Superseding DOE-STD-1090-96 September 1996 DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced from the best available copy. Available to DOE and DOE contractors from ES&H Technical Information Services, U.S. Department of Energy, (800) 473-4375, fax: (301) 903-9823. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 605-6000. DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) Summary of Changes as of March 1999

66

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 CONSTRUCTION HOISTING AND RIGGING EQUIPMENT REQUIREMENTS 15-i This chapter outlines the requirements for the safe use of hoisting and rigging equipment on construction projects at DOE installations. 15.1 GENERAL ...............................................................................................................................15-1 15.2 PERSONNEL QUALIFICATIONS.........................................................................................15-2 15.2.1 Qualified Operators of Mobile Cranes.......................................................................15-2 15.2.2 Qualified Operators of Forklift Trucks ......................................................................15-3 15.2.3 Qualified Riggers .......................................................................................................15-4

67

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 LOAD HOOKS 13-i Chapter 13 Load Hooks This chapter provides safety standards for the inspection, testing, and maintenance of load hooks installed on cranes or hoists and implements the requirements of ASME B30.10, Chapter 10-1, "Hooks." See Chapter 12, "Rigging Accessories," for rigging hook requirements. 13.1 GENERAL ...............................................................................................................................13-1 13.1.1 Marking......................................................................................................................13-1 13.1.2 Attachments ...............................................................................................................13-1

68

La Belle: rigging in the days of the spritsail topmast, a reconstruction of a seventeenth-century ship's rig  

E-Print Network (OSTI)

LA BELLE: RIGGING IN THE DAYS OF THE SPRITSAIL TOPMAST, A RECONSTRUCTION OF A SEVENTEENTH-CENTURY SHIP’S RIG A Thesis by CATHARINE LEIGH INBODY CORDER Submitted to the Office of Graduate Studies of Texas A&M University... in partial fulfillment of the requirements for the degree of MASTER OF ARTS December 2007 Major Subject: Anthropology LA BELLE: RIGGING IN THE DAYS OF THE SPRITSAIL TOPMAST, A RECONSTRUCTION OF A SEVENTEENTH-CENTURY SHIP’S RIG A...

Corder, Catharine Leigh Inbody

2008-10-10T23:59:59.000Z

69

Mode localization results and laboratory demonstration techniques with a multi-pendulum rig  

E-Print Network (OSTI)

. Perturbed system mode shapes, analytical, for R' = 0. 015. 16 Table III. Perturbed system mode shapes, analytical, for R' = 0. 04 (K, = 0. 908 N-m/rad, 1, = 0, 532 m). 17 Table IV. Perturbed system mode shapes, analytical, for R' = 0. 15 (K, = 3. 90 N.... Pendulum rig schematic Figure 2. Detail of pendulum rig. Figure 3. Graphical depiction of mode shapes given in Table I. 10 Figure 4. Depiction of perturbed mode shapes given in Table's II, III, and IV for: (a) Rs=0. 015; (b) R =0. 04; and (c) R =0. 15...

Bollich, Robert Kenneth Gerard

1992-01-01T23:59:59.000Z

70

La Belle: Rigging in the days of the spritsail topmast, a reconstruction of a seventeenth-century ship's rig  

E-Print Network (OSTI)

La Belle’s rigging assemblage has provided a rare and valuable source of knowledge of 17th-century rigging in general and in particular, French and small-ship rigging characteristics. With over 400 individual items including nearly 160 wood and iron...

Corder, Catharine Leigh Inbody

2009-05-15T23:59:59.000Z

71

Rigs to reefs: a petroleum industry perspective  

E-Print Network (OSTI)

, by implementing an ocean dumping program in conjunction with a rigs-to-reefs program, and through the development of new technology and methods to reduce transportation costs. Zn addition, the overall cost to industry participation can be reduced through... Environmental Enhancement and Fishing in the Seas (REEFS)" Task Force. This task force was comprised of representatives of federal and state government agencies, the oil and ocean industries, and the commercial and recreational fishing communities. Secretary...

Dubose, William Perry

1988-01-01T23:59:59.000Z

72

Open Rigging Through XML: Character Setup Utilizing Metadata and Node Based Editing  

E-Print Network (OSTI)

Manager. . . . . 22 7 The Rig Manager interface for an empty scene. . . . . . . . . . . . . . 23 8 The Rig Manager interface and “Rig Edit Mode” label on the viewport after clicking the “Create Rig” button. . . . . . . . . . . . . . . . . . . 24 9 The Rig... and replace them with code that performs the desired actions. For example, the node-based interface can be used to replace the task of authoring rig 6 definition files in a text editor so that the user never needs to learn the rig definition format. 7 3...

Kelly, Logan Scott

2014-02-19T23:59:59.000Z

73

Surveillance Guide - CPS 8.1 Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING AND RIGGING HOISTING AND RIGGING 1.0 Objective The objective of this surveillance is to examine hoisting and rigging operations to ensure that safe equipment and work practices are being used. The surveillance includes verification that hoisting and rigging work is performed in accordance with DOE requirements and best practices. 2.0 References 2.1 DOE O 440.1A, Worker Protection Management For Doe Federal And Contractor Employees 2.2 DOE-RL-92-36, Hanford Site Hoisting and Rigging Manual NOTE The DOE Hoisting and Rigging Manual should be used as the primary reference for this surveillance. 1 3.0 Requirements Implemented This surveillance is conducted to implement the RL Functions, Responsibilities, and Authorities Manual (FRAM) item No. 2504. 4.0 Surveillance Activities

74

Rig activity; 1991 is now the worst year on record  

SciTech Connect

This paper reports that U.S. rotary oil well drilling rig activity reached year-end levels above 1,100 rigs and averaged over 1,000 in 1990, the first increase since 1984. In 1991, however, operating rigs dropped once again, this time to an all time recorded low and once again, most forecasters erred on the high side. Rotary rigs running in 1991 averaged 862.8, a 14.4% drop below the 1990 activity level of 1007.8 rigs. The rig count, began at 1,068 in January, but fell steadily for the remainder of the year. A brief upturn at mid-year failed to hold up and the year-end increases in drilling we had come to expect since 1986 never materialized.

Not Available

1992-02-01T23:59:59.000Z

75

Rig activity; 1989 was the worst year on record  

SciTech Connect

This article discusses the quantity of oil rotary rigs running in the United States during 1989. Rotary rigs running in 1989 averaged 870, down 7.1% from 1988 and arguably the worst performance since anyone bothered to count. A quick check into dusty historical records reveals that in 1942 the rotary rig count averaged 761 (this was the result of a deliberate government policy of scaling back drilling). However, the number is misleading, because in the early 1940s cable-tool rigs were around 40% to 45% of the total operating at any given time.

Not Available

1990-02-01T23:59:59.000Z

76

Field Demonstraton of Existing Microhole Coiled Tubing Rig (MCTR) Technology  

SciTech Connect

The performance of an advanced Microhole Coiled Tubing Rig (MCTR) has been measured in the field during the drilling of 25 test wells in the Niobrara formation of Western Kansas and Eastern Colorado. The coiled tubing (CT) rig designed, built and operated by Advanced Drilling Technologies (ADT), was documented in its performance by GTI staff in the course of drilling wells ranging in depth from 500 to nearly 3,000 feet. Access to well sites in the Niobrara for documenting CT rig performance was provided by Rosewood Resources of Arlington, VA. The ADT CT rig was selected for field performance evaluation because it is one of the most advanced commercial CT rig designs that demonstrate a high degree of process integration and ease of set-up and operation. Employing an information collection protocol, data was collected from the ADT CT rig during 25 drilling events that encompassed a wide range of depths and drilling conditions in the Niobrara. Information collected included time-function data, selected parametric information indicating CT rig operational conditions, staffing levels, and field observations of the CT rig in each phase of operation, from rig up to rig down. The data obtained in this field evaluation indicates that the ADT CT rig exhibited excellent performance in the drilling and completion of more than 25 wells in the Niobrara under varied drilling depths and formation conditions. In the majority of the 25 project well drilling events, ROP values ranged between 300 and 620 feet per hour. For all but the lowest 2 wells, ROP values averaged approximately 400 feet per hour, representing an excellent drilling capability. Most wells of depths between 500 and 2,000 feet were drilled at a total functional rig time of less than 16 hours; for wells as deep at 2,500 to 3,000 feet, the total rig time for the CT unit is usually well under one day. About 40-55 percent of the functional rig time is divided evenly between drilling and casing/cementing. The balance of time is divided among the remaining four functions of rig up/rig down, logging, lay down bottomhole assembly, and pick up bottomhole assembly. Observations made during all phases of CT rig operation at each of the project well installations have verified a number of characteristics of the technology that represent advantages that can produce significant savings of 25-35 percent per well. Attributes of the CT rig performance include: (1) Excellent hole quality with hole deviation amounting to 1-2 degrees; (2) Reduced need for auxiliary equipment; (3) Efficient rig mobilization requiring only four trailers; (4) Capability of ''Zero Discharge'' operation; (5) Improved safety; and, (6) Measurement while drilling capability. In addition, commercial cost data indicates that the CT rig reduces drilling costs by 25 to 35% compared to conventional drilling technology. Widespread commercial use of the Microhole Coiled Tubing technology in the United States for onshore Lower-48 drilling has the potential of achieving substantially positive impacts in terms of savings to the industry and resource expansion. Successfully commercialized Microhole CT Rig Technology is projected to achieve cumulative savings in Lower-48 onshore drilling expenditures of approximately 6.8 billion dollars by 2025. The reduced cost of CT microhole drilling is projected to enable the development of gas resources that would not have been economic with conventional methods. Because of the reduced cost of drilling achieved with CT rig technology, it is estimated that an additional 22 Tcf of gas resource will become economic to develop. In the future, the Microhole Coiled Tubing Rig represents an important platform for the continued improvement of drilling that draws on a new generation of various technologies to achieve goals of improved drilling cost and reduced impact to the environment.

Kent Perry; Samih Batarseh; Sheriff Gowelly; Thomas Hayes

2006-05-09T23:59:59.000Z

77

Decision uncertainty minimization and autonomous information gathering  

E-Print Network (OSTI)

Over the past several decades, technologies for remote sensing and exploration have become increasingly powerful but continue to face limitations in the areas of information gathering and analysis. These limitations affect ...

Bush, Lawrence A. M

2013-01-01T23:59:59.000Z

78

Development of a portable grain mass flow sensor test rig  

Science Journals Connector (OSTI)

A portable grain mass flow sensor test rig was built to measure the accuracy of a mass flow sensor with dual use in the field as well as in the lab. Concurrently, a synchronization method was developed that employs GPS timing data to synchronize the ... Keywords: Mass flow sensor, Test rig, Yield monitor accuracy, Yield monitor error

M. Loghavi; R. Ehsani; R. Reeder

2008-05-01T23:59:59.000Z

79

HURRICANE PREDICTION, OIL RIGS, AND INSURANCE: KATRINA, RITA, AND BEYOND  

E-Print Network (OSTI)

on meteorological and oceanographic design specifications for offshore structures such as oil rigs. Dr. Forristall spent over 30 years as an offshore research engineer and advisor for Shell Oil, both nationallyHURRICANE PREDICTION, OIL RIGS, AND INSURANCE: KATRINA, RITA, AND BEYOND LUNCHEON BRIEFING

80

CRAD, Hoisting & Rigging Assessment Plan | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting & Rigging Assessment Plan Hoisting & Rigging Assessment Plan CRAD, Hoisting & Rigging Assessment Plan Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging equipment on a scheduled basis, certifying that safe operations are in

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

A Built for Purpose Micro-Hole Coiled Tubing Rig (MCTR)  

SciTech Connect

This report will serve as the final report on the work performed from the contract period October 2005 thru April 2007. The project 'A Built for Purpose Microhole Coiled Tubing Rig (MCTR)' purpose was to upgrade an existing state-of-the-art Coiled Tubing Drilling Rig to a Microhole Coiled Tubing Rig (MCTR) capable of meeting the specifications and tasks of the Department of Energy. The individual tasks outlined to meet the Department of Energy's specifications are: (1) Concept and development of lubricator and tool deployment system; (2) Concept and development of process control and data acquisition; (3) Concept and development of safety and efficiency improvements; and (4) Final unit integration and testing. The end result of the MCTR upgrade has produced a unit capable of meeting the following requirements: (1) Capable of handling 1-inch through 2-3/8-inch coiled tubing (Currently dressed for 2-3/8-inch coiled tubing and capable of running up to 3-1/2-inch coiled tubing); (2) Capable of drilling and casing surface, intermediate, production and liner hole intervals; (3) Capable of drilling with coiled tubing and has all controls and installation piping for a top drive; (4) Rig is capable of running 7-5/8-inch range 2 casing; and (5) Capable of drilling 5,000 ft true vertical depth (TVD) and 6,000 ft true measured depth (TMD).

Bart Patton

2007-09-30T23:59:59.000Z

82

Hoisting & Rigging ISMS Assessment Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Objective: Assess the institutional and department/division hoisting and Objective: Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are involved in the

83

Hoisting & Rigging ISMS Assessment Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Objective: Assess the institutional and department/division hoisting and Objective: Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are involved in the

84

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 HOSTILE ENVIRONMENTS 5-i Chapter 5 Hostile Environments This chapter describes provisions for hoisting and rigging operations in hostile work environments. 5.1 GENERAL ................................................................................................................................5-1 5.2 HOSTILE ENVIRONMENT PLAN ......................................................................................5-2 5.2.1 Marking and Posting ....................................................................................................5-2 5.2.2 Inspection and Testing .................................................................................................5-2 EXHIBIT I Hostile Environment Plan ............................................................................................5-3

85

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

11-i Chapter 11 11-i Chapter 11 Wire Rope and Slings CHAPTER 11 WIRE ROPE AND SLINGS This chapter provides requirements for the fabrication and use of wire rope and slings used in hoisting and rigging. 11.1 GENERAL ...............................................................................................................................11-1 11.2 WIRE ROPE ............................................................................................................................11-4 11.2.1 Wire-Rope Lays.........................................................................................................11-4 11.2.2 Wire-Rope Cores .......................................................................................................11-4 11.2.3 Wire Rope for General Purposes

86

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 HOSTILE ENVIRONMENTS 5-i Chapter 5 Hostile Environments This chapter describes provisions for hoisting and rigging operations in hostile work environments. 5.1 GENERAL................................................................................................................................5-1 5.2 HOSTILE ENVIRONMENT PLAN ......................................................................................5-2 5.2.1 Marking and Posting ....................................................................................................5-2 5.2.2 Inspection and Testing .................................................................................................5-2 EXHIBIT I Hostile Environment Plan ............................................................................................5-3

87

Sampling-based robotic information gathering algorithms  

Science Journals Connector (OSTI)

We propose three sampling-based motion planning algorithms for generating informative mobile robot trajectories. The goal is to find a trajectory that maximizes an information quality metric (e.g. variance reduction, information gain, or mutual information) ... Keywords: Motion and path planning, field robotics, robotic information gathering

Geoffrey A. Hollinger, Gaurav S. Sukhatme

2014-08-01T23:59:59.000Z

88

Bioenergy Business Partner Information Gathering Form  

E-Print Network (OSTI)

Bioenergy Business Partner Information Gathering Form Fax completed form to the Agribusiness.hnei.hawaii.edu/bmpp/stakeholders.asp Partners are organizations that perform, intend to perform, or should perform bioenergy processes and/or requirements. Please tell us about your organization and the role it plays in bioenergy production in Hawaii

89

Energy Department Addresses Largest Gathering of Geothermal Energy...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Addresses Largest Gathering of Geothermal Energy Stakeholders Energy Department Addresses Largest Gathering of Geothermal Energy Stakeholders October 4, 2012 - 1:00pm Addthis Photo...

90

Hoisting & Rigging Assessment Form | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting & Rigging Assessment Form Hoisting & Rigging Assessment Form Hoisting & Rigging Assessment Form Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are

91

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

on a scheduled basis, certifying that safe operations are in compliance with good conduct of operations. DOE-STD-1090-2001 HoistingRiggingPlan.doc More Documents &...

92

Odessa fabricator builds rig specifically for geothermal drilling...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

in the nation's oil and gas fields. Now the Odessa-based company is branching out into alternative energy. The company recently delivered its first Thermal Single rig, a...

93

Basic Rigging Workbook Training and Qualifications Program Office  

E-Print Network (OSTI)

. This instructor handbook incorporates the Subject Area's requirements, as well as information from the Department of Energy's (DOE's) Hoisting and Rigging Manual and ANSI B30.9. Definitions Asymmetrical load. An object

Ohta, Shigemi

94

Rotating head for rotary drilling rigs  

SciTech Connect

A rotating head is claimed for a rotary drilling rig which is to be secured to the top of a well pipe having an inner rotating portion with an opening therethrough which permits passage of drill pipe, pipe joints, and Kelly tools; the rotating portion has an annular drive rubber formed integrally with the top portion thereof. A rotating head drive bushing having an opening with a cross-sectional shape generally conforming to the cross-section of the Kelly tool to permit only sliding motion therebetween is provided with helical external ridges which produce a disengagable gripping action with the opening in the drive rubber at the top of the rotating portion of the rotating head. The rotating portion has a conventional stripper rubber at the bottom thereof and is mounted with a double roller bearing to provide low friction motion with respect to the fixed portion of the head. The double roller bearing is lubricated with a viscous lubricating material and paddles are provided between the sets of rollers of the double roller bearing for distributing the viscous lubricating material and in particular propel it onto the upper set of bearings; the upper body portion of the rotating head is readily detachable from the lower sleeve portion which is normally welded to the well conductor pipe.

Adams, J.R.

1983-09-27T23:59:59.000Z

95

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPENDIX A PROCUREMENT GUIDELINES A-1 Appendix A Procurement Guidelines This appendix provides reference guidance in preparing purchase requisitions for hoisting and rigging materials and equipment. Nationally recognized standards and specifications are referenced for listed items. However, caution should be used prior to procurement of special items in order to verify appropriate specification or standard reference and requirements. Some specific requirements listed in this appendix are more restrictive than consensus standard requirements, but are recommended to ensure materials of adequate quality and workmanship are provided. Quality receipt inspections should be provided for all received materials in order to verify compliance of all

96

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPENDIX A APPENDIX A PROCUREMENT GUIDELINES A-i Appendix A Procurement Guidelines This appendix provides reference guidance in preparing purchase requisitions for hoisting and rigging materials and equipment. Nationally recognized standards and specifications are referenced for listed items. However, caution should be used prior to procurement of special items in order to verify appropriate specification or standard reference and requirements. Some specific requirements listed in this appendix are more restrictive than consensus standard requirements, but are recommended to ensure materials of adequate quality and workmanship are provided. Quality receipt inspections should be provided for all received materials in order to verify compliance of all

97

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TERMINOLOGY AND DEFINITIONS 1-1 Chapter 1 Terminology and Definitions The following are specialized terms commonly used when discussing hoisting and rigging operations. Many may not be used in this standard, but are included for general information. The terms are arranged in alphabetical order. Illustrations are included for clarity. ABRASION: Surface wear. ACCELERATION STRESS: Additional stress imposed due to increasing load velocity. ALTERNATE LAY: Lay of wire rope in which the strands are alternately regular and lang lay. ANSI: American National Standards Institute. APPOINTED: Assigned specific responsibilities by the employer or the employer's representative. AREA, METALLIC: Sum of the cross- sectional areas of individual wires in a wire rope

98

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TERMINOLOGY AND DEFINITIONS 1-1 Chapter 1 Terminology and Definitions The following are specialized terms commonly used when discussing hoisting and rigging operations. Many may not be used in this standard, but are included for general information. The terms are arranged in alphabetical order. Illustrations are included for clarity. ABRASION: Surface wear. ACCELERATION STRESS: Additional stress imposed due to increasing load velocity. ALTERNATE LAY: Lay of wire rope in which the strands are alternately regular and lang lay. ANSI: American National Standards Institute. APPOINTED: Assigned specific responsibilities by the employer or the employer's representative. AREA, METALLIC: Sum of the cross- sectional areas of individual wires in a wire rope

99

Design and Analysis of a Test Rig for Modeling the Bit/Formation Interface in Petroleum Drilling Applications  

E-Print Network (OSTI)

and horizontal wells and measuring the effects of various factors on the stability of perturbations on the system. A test rig concept has been developed to accurately measure the interaction forces and torques between the bit, formation and fluids during drilling...

Wilson, Joshua Kyle

2013-04-11T23:59:59.000Z

100

Method for gathering and summarizing internet information  

DOE Patents (OSTI)

A computer method of gathering and summarizing large amounts of information comprises collecting information from a plurality of information sources (14, 51) according to respective maps (52) of the information sources (14), converting the collected information from a storage format to XML-language documents (26, 53) and storing the XML-language documents in a storage medium, searching for documents (55) according to a search query (13) having at least one term and identifying the documents (26) found in the search, and displaying the documents as nodes (33) of a tree structure (32) having links (34) and nodes (33) so as to indicate similarity of the documents to each other.

Potok, Thomas E. (Oak Ridge, TN); Elmore, Mark Thomas (Oak Ridge, TN); Reed, Joel Wesley (Knoxville, TN); Treadwell, Jim N. (Louisville, TN); Samatova, Nagiza Faridovna (Oak Ridge, TN)

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 BELOW-THE-HOOK LIFTING DEVICES 14-i Chapter 14 Below-the-Hook Lifting Devices This chapter provides the requirements for below-the-hook lifting devices used in hoisting and rigging, such as spreader bars, lifting yokes, and lift fixtures. This section implements the requirements of ASME B30.20, "Below-the-Hook Lifting Devices." NOTE: Special lifting devices for shipping containers weighing 10,000 lb or more that are used for radioactive materials may be governed by ANSI N14.6 ["Standard for Special Lifting Devices for Shipping Containers Weighing 10,000 Pounds (4,500 kg) or More for Nuclear Materials."] 14.1 GENERAL ...............................................................................................................................14-1

102

Professional development of new rig supervisors a must  

SciTech Connect

This paper reports that because the number of drilling personnel has dropped dramatically over the last decade, many operators now face a shortage of competent rig supervisors. To be effective, the rig supervisor must develop a knowledge of drilling operations, apply optimization techniques to improve drilling performance, demand safe work practices, and protect the environment. Petroleum engineering degree programs and industry training programs can teach the rig supervisor specific technical and management skills; however, traditionally, the supervisor trainee shadows an experienced company man to learn how to direct a drilling operation. The success of this method depends not only on the skills and learning capabilities of the trainee but also on the trainer's time, motivation, knowledge, and ability to teach the skills necessary to direct drilling activities.

Nordt, D.P. (Marathon Oil Co., Houston, TX (United States)); Stone, M.S. (Marathon Oil Co., Bridgeport, IL (United States))

1992-10-26T23:59:59.000Z

103

Natural Gas for the Long Haul (Big Rigs Go Green)  

NLE Websites -- All DOE Office Websites (Extended Search)

the Long Haul (Big Rigs Go Green) the Long Haul (Big Rigs Go Green) JOHN DAVIS: No one has been hit harder by rising fuel prices than America's long-haul commercial truckers. A big rig can easily burn 20,000 gallons of fuel a year, and with diesel prices projected to keep rising, this not only pinches the trucker's bottom line, but that extra cost is passed on to American consumers. Meanwhile, natural gas prices have remained stable and are forecast to stay that way for years to come. Up to now, demand for natural gas as a transportation fuel has been mostly for compressed natural gas used by light and medium-duty vehicles. City buses, refuse haulers, utilities, and

104

Inventory management of steel plates at an oil rig construction company .  

E-Print Network (OSTI)

??Keppel Fels produces make-to-order oil exploration rigs for the global market. Each rig requires close to 6000 metric tons of steel in the course of… (more)

Tan, Chien Yung

2006-01-01T23:59:59.000Z

105

Inventory management of steel plates at an oil rig construction company  

E-Print Network (OSTI)

Keppel Fels produces make-to-order oil exploration rigs for the global market. Each rig requires close to 6000 metric tons of steel in the course of its production. Optimal management of this steel is very critical in this ...

Tan, Chien Yung

2006-01-01T23:59:59.000Z

106

Doubts swirl around plan to use rigs as reefs  

Science Journals Connector (OSTI)

... Offshore oil platforms could be allowed to remain in place as artificial habitats for marine life ... oil stops flowing, and to leave the sites as they found them. But the Rigs to Reefs Act of 2003, which is sponsored by Representative David Vitter (Republican, ...

Betsy Mason

2003-10-30T23:59:59.000Z

107

Ministers block disposal of oil rigs at sea  

Science Journals Connector (OSTI)

... ministers last week ended three years of public controversy about the fate of disused oil rigs in the northeast Atlantic ocean. They decided that most will have to be dismantled ... all environmentalist groups. Oil companies, on the other hand, were disappointed. The UK Offshore Operators Association said the decision to outlaw deep-sea disposal of oil and gas ...

Ehsan Masood

1998-07-30T23:59:59.000Z

108

Hoisting and Rigging: Lift Planning and Control for Ordinary Lifts  

E-Print Network (OSTI)

operator Follow specific instructions/procedures for attachment of the rigging gear to the load. Use. Repeat as necessary until the load is evenly balanced. Follow "Conduct of Operator" requirements2 Stop at the work site and follow the plan Assign a designated leader Ensure all personnel involved in the lift

Wechsler, Risa H.

109

Mixed Stream Test Rig Winter FY-2011 Report  

SciTech Connect

This report describes the data and analysis of the initial testing campaign of the Mixed Stream Test Rig (MISTER) at Idaho National Laboratory (INL). It describes the test specimen selection, physical configuration of the test equipment, operations methodology, and data and analysis of specimens exposed in two environments designed to represent those expected for high temperature steam electrolysis (HTSE).

Chalres Park; Tedd Lister; Kevin DeWall

2011-04-01T23:59:59.000Z

110

Planning and scheduling a fleet of rigs using simulation-optimization  

Science Journals Connector (OSTI)

Some of the most important and expensive activities in the oil field development and production phases relate to using rigs. These can be used for drilling wells, or for maintenance activities. As rigs are usually scarce compared to the number of wells ... Keywords: Planning, Rigs, Scheduling, Simulation-optimization

Hugo ViníCius Bassi; VirgíLio Jose Martins Ferreira Filho; Laura Bahiense

2012-12-01T23:59:59.000Z

111

Tobacco vs. helminths in Congo basin hunter-gatherers Tobacco use vs. helminths in Congo basin hunter-gatherers  

E-Print Network (OSTI)

Tobacco vs. helminths in Congo basin hunter-gatherers 1 Tobacco use vs. helminths in Congo basin hunter-gatherers: Self-medication in humans? Casey J-546-9257 #12;Tobacco vs. helminths in Congo basin hunter-gatherers 2 Summary

112

Electric Motor Emulator Versus Rotating Test Rig  

Science Journals Connector (OSTI)

A controversial issue among experts is whether real-time model-based electric motor emulation can replace a conventional rotating test ... a complete inverter test system with an integrated electric motor emulato...

Dipl.-Ing. (FH) Horst Hammerer; Dipl.-Ing. (FH) Dieter Strauss

2012-06-01T23:59:59.000Z

113

UAV/UAS path planning for ice management information gathering.  

E-Print Network (OSTI)

??The key objective of this work is the proposition of the path planning strategy for unmanned aerial vehicle (UAV) intended for information gathering in Arctic… (more)

Stalmakou, Artsiom

2011-01-01T23:59:59.000Z

114

Rotary torque and rpm indicator for oil well drilling rigs  

SciTech Connect

Monitoring the torque applied by the rotary table to the drill string and the rpm of the drill string is provided. An intermediate adapter is positioned between the drill kelly and the rotary table. A strain gauge is attached to the intermediate adapter to measure torsional deformation and provide an indication of rotary torque. Transmission of torque data is accomplished by radio frequency transmission utilizing a transmitter on the intermediate adapter. A receiver is mounted to the side of the drill rig floor to receive and demodulate the torque signal. The intermediate adapter is rotating at the same rate as the drill string. Detection of the revolutions utilizing the changing R.F. Field strength is accomplished at the edge of the drill rig platform or elsewhere with a stationary sensor which doubles as the torque receiver. A highly directional torque transmitter antenna mounted on the adapter is used with the major lobe lying parallel to the rig floor and perpendicular to the pipe. By detecting the envelope of the radio frequency field strength, each rotation is marked by a peak. This enables continuous torque and rpm monitoring.

Chien, L.C.

1981-08-25T23:59:59.000Z

115

Social learning among Congo Basin hunter–gatherers  

Science Journals Connector (OSTI)

...Kevin N. Laland Social learning among Congo Basin hunter-gatherers Barry S. Hewlett...Central African Republic and Republic of Congo. We have conducted several years of qualitative...daily life and demographic features of Congo Basin hunter-gatherers and farmers...

2011-01-01T23:59:59.000Z

116

An energy-saving oil drilling rig for recovering potential energy and decreasing motor power  

Science Journals Connector (OSTI)

An energy-saving oil drilling rig is researched. A large accumulator is adopted in this rig to store the energy of the motor during the auxiliary time of lifting the drill stem and the potential energy of the drill stem when lowered. The equipped power of this rig decreases remarkably compared with the conventional drilling rig, and this rig can also recover and reuse the potential energy of the drill stem. Therefore, this rig owns remarkable energy-saving effect compared with the conventional drilling rig, and the energy-saving effect of the energy-saving oil drilling rig is also verified by the field tests. The mathematical model of the energy-saving oil drilling rig lowering the drill stem was derived and simulation analysis was conducted. Through simulation the curves of the drill stem lowering velocity and lowering displacement with time were obtained, and some conclusions were reached: (1) the heavier the drill stem lowered, the higher the lowering velocity is, and the shorter the lowering time is; (2) the smaller the displacement of the variable pump-motor, the higher the lowering velocity is, and the shorter the lowering time is.

Lujun Zhang

2011-01-01T23:59:59.000Z

117

CPS 8.1 Hoisting and Rigging, 2/25/2000  

Energy.gov (U.S. Department of Energy (DOE))

The objective of this surveillance is to examine hoisting and rigging operations to ensure that safe equipment and work practices are being used.  The surveillance includes verification that...

118

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division  

Energy.gov (U.S. Department of Energy (DOE))

:  To determine that hoisting and rigging operations areconducted according to “industry best standards” for increasing equipment reliabilitywhile assuring worker safety, and to verify issues being...

119

,,,,,"Rig: TOI Discoverer Enterprise"  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Well: OCS-G 32306 002 ST00BP00",,,,"Flow Data" Well: OCS-G 32306 002 ST00BP00",,,,"Flow Data" ,,,,,"Field: Mississippi Canyon 252" ,,,,,"Rig: TOI Discoverer Enterprise" ,,,,,"Choke Manifold",,,,"Rates",,,,,,,,,"Ratio" "Date","Time","Choke A","Choke B","BSW","WHPres","WHTemp","WHDCP","WHDCTemp","Gas Rate","Gas Cum","Uncorrected ","Uncorrected ","Water Rate","Water Cum","Uncorrected ","Uncorrected ","Cumulative Oil ","GOR1","Comments" ,,,,,,,,,,,"Oil Rate","Oil Cum ",,,"Liquid Rate","Liquid Cum","from Cargo "

120

Technical and economic evaluation of selected compact drill rigs for drilling 10,000 foot geothermal production wells  

SciTech Connect

This report summarizes the investigation and evaluation of several {open_quotes}compact{close_quotes} drill rigs which could be used for drilling geothermal production wells. Use of these smaller rigs would save money by reducing mobilization costs, fuel consumption, crew sizes, and environmental impact. Advantages and disadvantages of currently-manufactured rigs are identified, and desirable characteristics for the {open_quotes}ideal{close_quotes} compact rig are defined. The report includes a detailed cost estimate of a specific rig, and an evaluation of the cost/benefit ratio of using this rig. Industry contacts for further information are given.

Huttrer, G.W. [Geothermal Management Company, Inc., Frisco, CO (United States)

1997-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Planning and scheduling a fleet of rigs using simulation–optimization  

Science Journals Connector (OSTI)

Some of the most important and expensive activities in the oil field development and production phases relate to using rigs. These can be used for drilling wells, or for maintenance activities. As rigs are usually scarce compared to the number of wells requiring service, a schedule of wells to be drilled or repaired must be devised. The objective is to minimize opportunity costs within certain operating constraints. This paper present the first stochastic approach to deals with the problem of planning and scheduling a fleet of offshore oil rigs, where the service time is assumed being uncertain. A simulation–optimization method is used to generate “expected solutions” and performance measures for rigs, as well as statistics about well allocation to rigs. The methodology can be used in two different ways – to schedule an existing fleet of rigs or to scale the size of the fleet – both contemplating the uncertain nature of the problem. The method’s expected results include performance measures for each rig, expected delay for a well to be served, the expected schedule of rigs, and a distribution of the well servicing order. The experiments based on real situations demonstrate the effectiveness of the simulation–optimization approach.

Hugo Vinícius Bassi; Virgílio Jose Martins Ferreira Filho; Laura Bahiense

2012-01-01T23:59:59.000Z

122

Structural Basis of Viral RNA Recognition by RIG-I-Like Receptors  

E-Print Network (OSTI)

binding surface also abolished RIG-I signaling in cells. In order to compare the RIG-I/RNA interactions with other RLRs, we also determined the dsRNA binding surface of MDA5 CTD by NMR titration studies. MDA5 CTD has a similar binding surface...

Lu, Cheng

2012-10-19T23:59:59.000Z

123

Numerical and experimental determination of neutron characteristics in irradiation rigs operated in LVR-15 research reactor  

Science Journals Connector (OSTI)

......standard single-cell CHOUCA rigs or...dedicated multi-cell rigs. The temperature...reflector and in fuel will be provided...dedicated to material degradation evaluation. IRRADIATION...evaluation of material degradation induced by radiation...averaged over cell) has to be modified...reflects actual fuel burnup distribution......

Michal Koleska; Ladislav Viererbl; Zdena Lahodova; Jaroslav Ernest; Jelena Zmitkova; Milan Marek

2014-10-01T23:59:59.000Z

124

Safety First Safety Last Safety Always Inspect rigging equipment for material handling before use  

E-Print Network (OSTI)

Safety First Safety Last Safety Always Inspect rigging equipment for material handling before use. Rigging Equipment for Material Handling Safety Tip #19 At your job or at the plate, you can't get home on the reverse side of this safety tip sheet. Please refrain from reading the information verbatim

Minnesota, University of

125

The design of a test rig for the identification of dynamic coefficients of a high temperature magnetic bearing  

E-Print Network (OSTI)

This thesis is a report on the research and Micrographics. development to design a test rig for the identification of the dynamic coefficients of a radial magnetic bearing. The test rig development is intended for dynamic coefficient observation...

Rahtika, I Putu Gede Sopan

1998-01-01T23:59:59.000Z

126

Selectively fired, tubing-conveyed perforating guns save rig time  

SciTech Connect

Selective firing of tubing-conveyed perforating (TCP) guns during drill stem tests (DSTs) added flexibility and saved costs for Marathon Oil Co. As an example, in the Garland field in Wyoming, the guns allowed perforating multiple zones in one trip. This saved 1 1/2--2 days/well in rig time and $25,000--30,000/well in electric wire line and DST tool charges. For international offshore operations, savings of $200,000/well appear possible. Savings result not only from perforating multiple zones, but also from arbitrarily setting firing patterns with or without zone isolation. The paper describes the testing of equipment, the design of the guns, firing heads, crossover assembly, pressure isolation sub, control line, and select-fire sub, and applications for the guns.

Snider, P.M. (Marathon Oil Co., Houston, TX (United States)); Bond, P.L. (Halliburton Energy Services, Dallas, TX (United States))

1993-07-19T23:59:59.000Z

127

Topic Area 2: Data Gathering and Analysis | Open Energy Information  

Open Energy Info (EERE)

2: Data Gathering and Analysis 2: Data Gathering and Analysis Jump to: navigation, search Geothermal ARRA Funded Projects for Topic Area 2: Data Gathering and Analysis Loading map... {"format":"googlemaps3","type":"ROADMAP","types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"limit":200,"offset":0,"link":"all","sort":[""],"order":[],"headers":"show","mainlabel":"","intro":"","outro":"","searchlabel":"\u2026 further results","default":"","geoservice":"google","zoom":false,"width":"600px","height":"350px","centre":false,"layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","icon":"","visitedicon":"","forceshow":true,"showtitle":true,"hidenamespace":false,"template":false,"title":"","label":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"locations":[{"text":"

128

OSTI News Transcripts, International Group Gathers in Knoxville to Discuss  

Office of Scientific and Technical Information (OSTI)

OSTI News Transcripts, International Group Gathers in Knoxville to Discuss OSTI News Transcripts, International Group Gathers in Knoxville to Discuss Sharing Science across Borders, ETDE, Office of Scientific and Technical Information, U.S. Department of Energy, www.osti.gov International Group Gathers in Knoxville to Discuss Sharing Science across Borders (October 2006) ETDE Listen Now The desire to share science across international boundaries brought representatives from 11 countries to the Knoxville area in early October. "Sharing research can lead to invaluable opportunities in the commercial, academic and government sectors," said Brian Hitson, chairman of the Energy Technology Data Exchange, or ETDE, executive committee. "The countries attending, and others within our membership, have chosen to make sure research information is exchanged cost effectively."

129

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 HOISTS 8-i Chapter 8 Hoists This chapter provides safety standards for inspecting, testing, and operating hoists not permanently mounted on overhead cranes and implements the requirements of ASME B30.11 ("Monorail Systems and Underhung Cranes"), B30.16["Overhead Hoists (Underhung)"], and B30.21 ("Manually Lever Operated Hoists"). 8.1 GENERAL .................................................................................................................................8-1 8.1.1 Operator Training/Qualification ..................................................................................8-4 8.1.2 Marking........................................................................................................................8-4

130

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 OVERHEAD AND GANTRY CRANES 7-i Chapter 7 Overhead and Gantry Cranes This chapter specifies operation, inspection, maintenance, and testing requirements for the use of overhead and gantry cranes and implements the requirements of ASME B30.2 ["Overhead and Gantry Cranes (Top- Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist)"], B30.11 ("Monorail Systems and Underhung Cranes"), and B30.17 ["Overhead and Gantry Cranes (Top-Running Bridge, Single Girder, Underhung Hoist")]. Only equipment built to the appropriate design standards shall be used in DOE installations. 7.1 GENERAL .................................................................................................................................7-1

131

International Gathering Plans Ways To Safeguard Atmospheric Ozone  

Science Journals Connector (OSTI)

International Gathering Plans Ways To Safeguard Atmospheric Ozone ... Everyone's for it, as was evidenced in Helsinki recently where senior government officials from more than 80 countries, together with delegates representing many interested groups and organizations, attended a week-long meeting to seek ways of safeguarding it. ...

DERMOT A. O'SULLIVAN

1989-06-26T23:59:59.000Z

132

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division : To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001

133

Motor Drives of Modern Drilling and Servicing Rigs for Oil and Gas Wells  

Science Journals Connector (OSTI)

This paper provides a synthetic view on the most recent achievements in the field of drilling and servicing rig drives for oil and gas wells. This field is featuring ... kilowatts and speeds of 150–250 rpm for drilling

Aurelian Iamandei; Gheorghe Miloiu

2013-01-01T23:59:59.000Z

134

E-Print Network 3.0 - advanced seal rig Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

2 3 4 5 > >> Page: << < 1 2 3 4 5 > >> 41 Heat Transfer Research, 2010, Vol. 41, No. 6 Turbine Aero-Heat Transfer Studies Summary: , rotating turbine research rigs, realistic gas...

135

U. S. rig count drops below 600, a post-1940 low  

SciTech Connect

This paper reports that the Baker Hughes Inc. count of active U.S. rotary rigs as of June 12 fell to less than 600 the first time since that tally began in 1940. The previous modern record low was set at 610 the previous week. Baker Hughes reported about 1,400 rigs idle in the U.S. last week. Using a different criteria, the Smith International count of U.S. active rigs fell seven units to 653 the week ended June 12, compared with a count of 910 the previous year. Baker Hughes predecessor Hughes Tool Co. began keeping monthly records of active U.S. rigs in January 1940. The lowest monthly count that year was 857. It changed to a weekly count in January 1949. The milestone was met wit calls for relief for the U.S. upstream sector from industry and government officials in Washington.

Not Available

1992-06-22T23:59:59.000Z

136

Analytical and experimental investigations of a labyrinth seal test rig and damper seals for turbomachinery  

E-Print Network (OSTI)

. The test rig is also used during the development of a unique damper seal device. The experimental data used to determine the direct damping coefficient of the damper seal device are presented. Results of vibration and pressure measurements that demonstrate...

Shultz, Richard Raymond

1997-01-01T23:59:59.000Z

137

Energy Department Addresses Largest Gathering of Geothermal Energy Stakeholders  

Energy.gov (U.S. Department of Energy (DOE))

U.S. Department of Energy investments are tapping a vast resource of clean, baseload energy from the earth's heat, according to Douglas Hollett, Program Manager for the Department's Geothermal Technologies Office. Hollett addressed over 1,000 this week at the annual conference of the Geothermal Resources Council (GRC) in Reno, Nevada—the industry's largest annual gathering of geothermal energy stakeholders in the nation.

138

TRAC-PF1/MOD3 calculations of Savannah River Laboratory Rig FA single-annulus heated experiments  

SciTech Connect

This paper presents the results of TRAC-PF1/MOD3 benchmarks of the Rig FA experiments performed at the Savannah River Laboratory to simulate prototypic reactor fuel assembly behavior over a range of fluid conditions typical of the emergency cooling system (ECS) phase of a loss-of-coolant accident (LOCA). The primary purpose of this work was to use the SRL Rig FA tests to qualify the TRAC-PF1/MOD3 computer code and models for computing Mark-22 fuel assembly LOCA/ECS power limits. This qualification effort was part of a larger effort undertaken by the Los Alamos National Laboratory for the US Department of Energy to independently confirm power limits for the Savannah River Site K Reactor. The results of this benchmark effort as discussed in this paper demonstrate that TRAC/PF1/MOD3 coupled with proper modeling is capable of simulating thermal-hydraulic phenomena typical of that encountered in Mark-22 fuel assembly during LOCA/ECS conditions.

Fischer, S.R.; McDaniel, C.K.

1992-01-01T23:59:59.000Z

139

Executing a gather operation on a parallel computer  

DOE Patents (OSTI)

Methods, apparatus, and computer program products are disclosed for executing a gather operation on a parallel computer according to embodiments of the present invention. Embodiments include configuring, by the logical root, a result buffer or the logical root, the result buffer having positions, each position corresponding to a ranked node in the operational group and for storing contribution data gathered from that ranked node. Embodiments also include repeatedly for each position in the result buffer: determining, by each compute node of an operational group, whether the current position in the result buffer corresponds with the rank of the compute node, if the current position in the result buffer corresponds with the rank of the compute node, contributing, by that compute node, the compute node's contribution data, if the current position in the result buffer does not correspond with the rank of the compute node, contributing, by that compute node, a value of zero for the contribution data, and storing, by the logical root in the current position in the result buffer, results of a bitwise OR operation of all the contribution data by all compute nodes of the operational group for the current position, the results received through the global combining network.

Archer, Charles J. (Rochester, MN); Ratterman, Joseph D. (Rochester, MN)

2012-03-20T23:59:59.000Z

140

Autonomous gathering of livestock using a multi-functional sensor network platform  

E-Print Network (OSTI)

In this paper we develop algorithms and hardware for the autonomous gathering of cattle. We present a comparison of three different autonomous gathering algorithms that employ sound and/or electric stimuli to guide the ...

Doniec, Marek Wojciech

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Star Formation in Mergers and Interacting Galaxies: Gathering the Fuel  

E-Print Network (OSTI)

Selected results from recent studies of star formation in galaxies at different stages of interaction are reviewed. Recent results from the Spitzer Space Telescope are highlighted. Ideas on how large-scale driving of star formation in interacting galaxies might mesh with our understanding of star formation in isolated galaxies and small scale mechanisms within galaxies are considered. In particular, there is evidence that on small scales star formation is determined by the same thermal and turbulent processes in cool compressed clouds as in isolated galaxies. If so, this affirms the notion that the primary role of large-scale dynamics is to gather and compress the gas fuel. In gas-rich interactions this is generally done with increasing efficiency through the merger process.

Curtis Struck

2006-10-06T23:59:59.000Z

142

Rigging a horse and rider: simulating the predictable and repetitive movement of the rider  

E-Print Network (OSTI)

setup. If an animation piece is only going to have a few shots with a horse and rider, then the trouble of setting up an automated character rig is not practical, but if there are a significant amount of shots with a horse and rider galloping across...

Kuhnel, Jennifer Lynn

2004-09-30T23:59:59.000Z

143

AbstractThe red snapper (Lutjanus campechanus) is currently under rig  

E-Print Network (OSTI)

653 Abstract­The red snapper (Lutjanus campechanus) is currently under rig orous federal and state of annuli in otolith thin sections have been used to age many species of fish, including red snapper. However, the utility of this method for aging red snapper has been questioned by those who dispute both

144

Department of Mechanical Engineering Fall 2009 Air Products-Entrained Particle Flow Test Rig  

E-Print Network (OSTI)

PENNSTATE Department of Mechanical Engineering Fall 2009 Air Products-Entrained Particle Flow Test are causing catalyst plugging. Objectives Air Products requested that a test rig be constructed to entrain the hydrogen reforming facilities and aid Air Products in understanding the plugging problem. Approach

Demirel, Melik C.

145

Solid-State Lighting: Industry Leaders, Research Experts Gather for 2006  

NLE Websites -- All DOE Office Websites (Extended Search)

Industry Leaders, Research Industry Leaders, Research Experts Gather for 2006 DOE Solid-State Lighting Workshop to someone by E-mail Share Solid-State Lighting: Industry Leaders, Research Experts Gather for 2006 DOE Solid-State Lighting Workshop on Facebook Tweet about Solid-State Lighting: Industry Leaders, Research Experts Gather for 2006 DOE Solid-State Lighting Workshop on Twitter Bookmark Solid-State Lighting: Industry Leaders, Research Experts Gather for 2006 DOE Solid-State Lighting Workshop on Google Bookmark Solid-State Lighting: Industry Leaders, Research Experts Gather for 2006 DOE Solid-State Lighting Workshop on Delicious Rank Solid-State Lighting: Industry Leaders, Research Experts Gather for 2006 DOE Solid-State Lighting Workshop on Digg Find More places to share Solid-State Lighting: Industry Leaders,

146

Chancellor Blumenthal & his wife, Kelly Weisberg, cordially invite you to a Holiday Gathering & Campus Celebration  

E-Print Network (OSTI)

Chancellor Blumenthal & his wife, Kelly Weisberg, cordially invite you to a Holiday Gathering; UCSC Student #12;El Canciller Blumenthal y su esposa, Kelly Weisberg, lo invitan cordialmente

California at Santa Cruz, University of

147

GTO Director Doug Hollett Delivers Keynote at the Nation's Largest Industry Gathering, September 29, 2014  

Energy.gov (U.S. Department of Energy (DOE))

The Energy Department's Geothermal Technologies Office participated in the industry's largest geothermal gathering in Portland, Oregon, with a keynote address by Director Doug Hollett.

148

Rigging skeletal perissodactyl and artiodactyl ungulate limbs using analytic inverse kinematic-based solutions for a feature film production environment  

E-Print Network (OSTI)

The goal of this thesis is to develop and construct a repeatable, scalable, and portable rigging solution for the skeletal limbs of ungulates, maximizing functionality while streamlining intuitive interface controls for a feature film production...

Telford, William Lawrence, Jr

2007-04-25T23:59:59.000Z

149

A test rig for the identification of rotordynamic coefficients of fluid film bearings  

E-Print Network (OSTI)

. The test bearing articles were considered for cryogenic applications where the actual lubrication medium is liquid hydrogen or liquid oxygen. The parameter identification method used an advanced pseudo-random forcing excitation and a technique based...A TEST RIG FOR THE IDENTIFICATION OF ROTORDYNAMIC COEFFICIENTS OF FLUID FILM BEARINGS A Thesis LEWIS MILLER ROBISON III Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements...

Robison, Lewis Miller

1995-01-01T23:59:59.000Z

150

Large scale test rig for flow visualization and leakage measurement of labyrinth seals  

E-Print Network (OSTI)

number. Heffner (1959) measured the leakage rates of air through stationary true size labyrinth seals with the goal of predicting leakage rates for new seal designs through correlation charts developed from his investigation. Leakage resistance... geometries and land surfaces with the objective of obtaining optimized seal design criteria. The test rig utilized a flat two-dimensional stationary seal with a radial clearance-to-width ratio of approximately 100:1 to reduce wall end effects. Air...

Broussard, Daniel Harold

2012-06-07T23:59:59.000Z

151

A Method Of Evaluating A Subsurface Region Using Gather Sensitive Data Discrimination  

DOE Patents (OSTI)

A method of evaluating a subsurface region by separating/enhancing a certain type of seismic event data of interest from an overall set of seismic event data which includes other, different types of seismic event data is disclosed herein. In accordance with one feature, a particular type of gather is generated from the seismic event data such that the gather includes at least a portion of the data which is of interest and at least a portion of the other data. A series of data discrimination lines are incorporated into the gather at positions and directions which are established in the gather in a predetermined way. Using the data discrimination lines, the data of interest which is present in the gather is separated/enhanced with respect to the other data within the gather. The separated data may be used for example in producing a map of the particular subterranean region. In accordance with another feature, the gather is selected such that the incorporated discrimination lines approach a near parallel relationship with one another. Thereby, the data is transformed in a way which causes the discrimination lines to be parallel with one another, resulting in reduced frequency distortion accompanied by improved accuracy in the separation/enhancement of data. In accordance with still another feature, the disclosed data separation/enhancement method is compatible with an iterative approach.

Lazaratos, Spyridon K. (Houston, TX)

2000-01-11T23:59:59.000Z

152

A Context Gathering Framework for Context-Aware Mobile Solutions  

E-Print Network (OSTI)

]: Distributed Systems ­ Client/Server, Distributed Applications General Terms Design, Standardization, Languages in her refrigerator, thus he suggests a menu and a related shopping list to RB. The shopping list is not only based on the contents of the refrigerator, but it also takes into account the Cheryl

Bargiela, Andrzej

153

Networked Information Gathering and Fusion of PMU Data  

E-Print Network (OSTI)

- infrastructure. The smart grid in the making is envisaged to integrate a considerable amount of renewable energy Grid to Enable Sustainable Energy Systems" Funded by the U.S. Department of Energy White Paper Team as one of nine broad analysis white papers in the project "The Future Grid to Enable Sustainable Energy

154

Networked Information Gathering and Fusion of PMU Data  

E-Print Network (OSTI)

of renewable energy resources, which are highly variable. To meet these challenges, a key step is to develop of nine white papers in the project "The Future Grid to Enable Sustainable Energy Systems: An Initiative California Edison #12;ii Executive Summary The nation's power grid is perhaps the most dynamic

155

Factors influencing the incidence rates of injuries and accidents among seafarers and rig workers providing support to the WA offshore oil and gas industry.  

E-Print Network (OSTI)

??The aim of this study was to identify, discuss and make recommendations regarding causal factors associated with injuries and accidents among seafarers and rig workers… (more)

Martinovich, Tony, Dr

2013-01-01T23:59:59.000Z

156

Continuous injection of an inert gas through a drill rig for drilling into potentially hazardous areas  

SciTech Connect

A drill rig for drilling in potentially hazardous areas includes a drill having conventional features such as a frame, a gear motor, gear box, and a drive. A hollow rotating shaft projects through the drive and frame. An auger, connected to the shaft is provided with a multiplicity of holes. An inert gas is supplied to the hollow shaft and directed from the rotating shaft to the holes in the auger. The inert gas flows down the hollow shaft, and then down the hollow auger, and out through the holes in the bottom of the auger into the potentially hazardous area.

McCormick, S.H.; Pigott, W.R.

1998-04-01T23:59:59.000Z

157

An Advisory System For Selecting Drilling Technologies and Methods in Tight Gas Reservoirs  

E-Print Network (OSTI)

). 13 Fig. 6? Rotary drilling process (Bourgoyne et al. 1986). Two main systems are currently used to rotate the drill bit. As of 2007, for onshore drilling, 55% of the drilling rigs are equipped with a rotary table and Kelly- bushing while 45... ................................................................................................ 11 2.2.2. Discussion .................................................................................................. 12 2.3 Fit For Purpose Land Rig ................................................................................. 16 2.4 Slim...

Pilisi, Nicolas

2010-01-16T23:59:59.000Z

158

NREL: Vehicles and Fuels Research - NREL and Thought Leaders Gather at  

NLE Websites -- All DOE Office Websites (Extended Search)

NREL and Thought Leaders Gather at Electric Vehicle Battery Management NREL and Thought Leaders Gather at Electric Vehicle Battery Management Summit Battery cyclers in NREL's Thermal Test Facility. The January 10 tour will feature NREL's Thermal Test Facility, which houses equipment including these battery cyclers used in AMPED research. Photo by Dennis Schroeder, NREL December 23, 2013 From January 8 to 10, 2014, National Renewable Energy Laboratory (NREL) researchers, U.S. Department of Energy (DOE) program directors and technology managers, and other thought leaders will gather in Denver, Colorado, to exchange strategies for maximizing the performance, safety, and lifespan of the next generation of electric-drive vehicle (EDV) batteries. This annual review of DOE Advanced Research Projects Agency-Energy's (ARPA-E's) Advanced Management and Protection of Energy

159

NAS-NAE National Convocation on "Rising Above the Gathering Storm Two Years  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NAS-NAE National Convocation on "Rising Above the Gathering Storm NAS-NAE National Convocation on "Rising Above the Gathering Storm Two Years Later: Accelerating Progress toward a Brighter Economic Future" NAS-NAE National Convocation on "Rising Above the Gathering Storm Two Years Later: Accelerating Progress toward a Brighter Economic Future" April 29, 2008 - 11:31am Addthis Remarks As Prepared for Delivery by Secretary Bodman Thank you, Tom for that kind introduction. And I want to commend you, Norm Augustine and Chuck Vest for your continued leadership on these issues. You are powerful voices for urgent and sustained action to preserve this nation's technological preeminence - and our economic competitiveness. It's a pleasure to be here with you all, and with my good friends Margaret and Carlos. It strikes me that we are in the fortunate position of

160

International Clean Coal, Carbon Capture Experts to Gather at 28th Annual  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Clean Coal, Carbon Capture Experts to Gather at 28th Clean Coal, Carbon Capture Experts to Gather at 28th Annual Pittsburgh Coal Conference International Clean Coal, Carbon Capture Experts to Gather at 28th Annual Pittsburgh Coal Conference August 10, 2011 - 1:00pm Addthis Washington, DC - The role of fossil fuels in a sustainable energy future will be one of the topics under discussion when experts from around the world meet at the 28th Annual International Pittsburgh Coal Conference, Sept. 12-15, at the David L. Lawrence Convention Center in Pittsburgh, Pa. Hosted by the University of Pittsburgh's Swanson School of Engineering, the conference is attended by industry, government and academia representatives from around the world. It focuses on environmental and technological issues surrounding the continued use of coal and the

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

International Clean Coal, Carbon Capture Experts to Gather at 28th Annual  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

International Clean Coal, Carbon Capture Experts to Gather at 28th International Clean Coal, Carbon Capture Experts to Gather at 28th Annual Pittsburgh Coal Conference International Clean Coal, Carbon Capture Experts to Gather at 28th Annual Pittsburgh Coal Conference August 10, 2011 - 1:00pm Addthis Washington, DC - The role of fossil fuels in a sustainable energy future will be one of the topics under discussion when experts from around the world meet at the 28th Annual International Pittsburgh Coal Conference, Sept. 12-15, at the David L. Lawrence Convention Center in Pittsburgh, Pa. Hosted by the University of Pittsburgh's Swanson School of Engineering, the conference is attended by industry, government and academia representatives from around the world. It focuses on environmental and technological issues surrounding the continued use of coal and the

162

ORIGINAL ARTICLES Global Public Health Implications of a Mass Gathering in Mecca,  

E-Print Network (OSTI)

I SM T 75 ORIGINAL ARTICLES Global Public Health Implications of a Mass Gathering in Mecca, Saudi on Inner City Health, Keenan Research Centre in the Li Ka Shing Knowledge Institute of St. Michael of Toronto, Toronto, Ontario, Canada; Department of Health Policy, Management and Evaluation, University

Arino, Julien

163

Internet Research: Comments on Formulating the Problem Gathered by Sally Floyd,  

E-Print Network (OSTI)

Internet Research: Comments on Formulating the Problem Gathered by Sally Floyd, with contributions Introduction This note contains a discussion about formulating the research problem for Internet research the implications of these assumptions in formulating problems in Internet re- search. This process would aim

Floyd, Sally

164

Internet Research: Comments on Formulating the Problem Gathered by Sally Floyd,  

E-Print Network (OSTI)

Internet Research: Comments on Formulating the Problem Gathered by Sally Floyd, with contributions Introduction This note contains a discussion about formulating the research problem for Internet research the implications of these assumptions in formulating problems in Internet re­ search. This process would aim

Floyd, Sally

165

A Probabilistic Model of Action for Least-Commitment Planning with Information Gathering  

E-Print Network (OSTI)

an operator paint that usu- ally makes PA true. Although the robot cannot immediately tell whether to gather information, and acting based on that information. A robot is given the task of processing a widget. Its goal is to have the widget painted (PA) and processed (PR) and #12;nally notifying its

166

Flexible and Persistent Tool-using Strategies in Honey-gathering by Wild Chimpanzees  

E-Print Network (OSTI)

of chimpanzees in the Congo Basin indicate that they may have developed sophisticated technical solutions in honey-gathering by chimpanzees in the Goualougo Triangle, Republic of Congo. Pounding was the most the Congo Basin. Int J Primatol (2009) 30:411­427 DOI 10.1007/s10764-009-9350-5 C. M. Sanz (*) Department

167

Delay-Tolerant Data Gathering in Energy Harvesting Sensor Networks With a Mobile Sink  

E-Print Network (OSTI)

Delay-Tolerant Data Gathering in Energy Harvesting Sensor Networks With a Mobile Sink Xiaojiang Ren collection in an energy harvesting sensor network with a mobile sink, where a mobile sink travels along, this is the first kind of work of data collection for energy harvesting sensor networks with mobile sinks. I

Liang, Weifa

168

Industry Leaders, Research Experts Gather for Fourth Annual DOE Solid-State Lighting Workshop  

Energy.gov (U.S. Department of Energy (DOE))

More than 250 attendees gathered in Phoenix, Arizona, to participate in the 2007 DOE Solid-State Lighting (SSL) Program Planning Workshop on January 31-February 2, 2007. Lighting industry leaders, fixture manufacturers, researchers, academia, trade associations, lighting designers, energy efficiency organizations, and utilities joined DOE to share perspectives on the rapidly evolving SSL market. The workshop provided a forum for building partnerships and strategies to accelerate technology advances and guide market introduction of high efficiency, high-performance SSL products.

169

Industry Leaders, Research Experts Gather for Second Annual DOE Solid-State Lighting Workshop  

Energy.gov (U.S. Department of Energy (DOE))

Technology leaders from industry, research institutions, universities, and national laboratories gathered in San Diego, California, on February 3 and 4, 2005 to attend a workshop focused on advancing solid-state lighting (SSL) technology from the laboratory to the marketplace. Sponsored by the U.S. Department of Energy (DOE) Building Technologies Office, the workshop provided an interactive forum for shaping and prioritizing DOE's SSL research and development activities.

170

Dynamic accident modeling for high-sulfur natural gas gathering station  

Science Journals Connector (OSTI)

Abstract Dynamic accident modeling for a gas gathering station is implemented to prevent high-sulfur natural gas leakage and develop equipment inspection strategy. The progress of abnormal event occurring in the gas gathering station is modeled by the combination of fault tree and event sequence diagram, based on accident causal chain theory, i.e. the progress is depicted as sequential failure of safety barriers, then, the occurrence probability of the consequence of abnormal event is predicted. Consequences of abnormal events are divided into accidents and accident precursors which include incidents, near misses and so on. The Bayesian theory updates failure probability of safety barrier when a new observation (i.e. accident precursors or accidents data) arrives. Bayesian network then correspondingly updates failure probabilities of basic events of the safety barriers with the ability of abductive reasoning. Consequence occurrence probability is also updated. The results show that occurrence probability trend of different consequences and failure probability trend of safety barriers and basic events of the safety barriers can be obtained using this method. In addition, the critical basic events which play an important role in accidents occurrence are also identified. All of these provide useful information for the maintenance and inspection of the gas gathering station.

Qinglei Tan; Guoming Chen; Lei Zhang; Jianmin Fu; Zemin Li

2014-01-01T23:59:59.000Z

171

An Adaptive Energy-Efficient and Low-Latency MAC for Data Gathering in Wireless Sensor Networks  

E-Print Network (OSTI)

nodes to a sink through a unidirectional tree. In this paper, we propose DMAC, an energy efficient gathering trees in sensor networks, DMAC provides significant energy savings and latency re- duction whileAn Adaptive Energy-Efficient and Low-Latency MAC for Data Gathering in Wireless Sensor Networks

Krishnamachari, Bhaskar

172

IEEE TRANSACTIONS ON WIRELESS COMMUNICATIONS, VOL. 5, NO. 11, NOVEMBER 2006 3087 Energy Minimization for Real-Time Data Gathering  

E-Print Network (OSTI)

objective is to minimize the overall energy cost of the sensor nodes in the data gathering tree subjectIEEE TRANSACTIONS ON WIRELESS COMMUNICATIONS, VOL. 5, NO. 11, NOVEMBER 2006 3087 Energy problem of energy minimization for data gathering over a multiple-sources single-sink communication

Krishnamachari, Bhaskar

173

Estimating contact rates at a mass gathering by using video analysis: a proof-of-concept project  

SciTech Connect

Current approaches for estimating social mixing patterns and infectious disease transmission at mass gatherings have been limited by various constraints, including low participation rates for volunteer-based research projects and challenges in quantifying spatially and temporally accurate person-to-person interactions. We developed a proof-of-concept project to assess the use of automated video analysis for estimating contact rates of attendees of the GameFest 2013 event at Rensselaer Polytechnic Institute (RPI) in Troy, New York. Video tracking and analysis algorithms were used to estimate the number and duration of contacts for 5 attendees during a 3-minute clip from the RPI video. Attendees were considered to have a contact event if the distance between them and another person was =1 meter. Contact duration was estimated in seconds. We also simulated 50 attendees assuming random mixing using a geo-spatially accurate representation of the same GameFest location. The 5 attendees had an overall median of 2 contact events during the 3-minute video clip (range: 0 6). Contact events varied from less than 5 seconds to the full duration of the 3- minute clip. The random mixing simulation was visualized and presented as a contrasting example. We were able to estimate the number and duration of contacts for five GameFest attendees from a 3-minute video clip that can be compared to a random mixing simulation model at the same location. The next phase will involve scaling the system for simultaneous analysis of mixing patterns from hours-long videos and comparing our results with other approaches for collecting contact data from mass gathering attendees.

Rainey, Jeanette J [ORNL; Cheriyadat, Anil M [ORNL; Radke, Richard J [ORNL; Crumly, Julie K [ORNL; Koch, Daniel B [ORNL

2014-01-01T23:59:59.000Z

174

Designing Topology-Aware Collective Communication Algorithms for Large Scale InfiniBand Clusters: Case Studies with Scatter and Gather  

SciTech Connect

Modern high performance computing systems are being increasingly deployed in a hierarchical fashion with multi-core computing platforms forming the base of the hierarchy. These systems are usually comprised of multiple racks, with each rack consisting of a finite number of chassis, with each chassis having multiple compute nodes or blades, based on multi-core architectures. The networks are also hierarchical with multiple levels of switches. Message exchange operations between processes that belong to different racks involve multiple hops across different switches and this directly affects the performance of collective operations. In this paper, we take on the challenges involved in detecting the topology of large scale InfiniBand clusters and leveraging this knowledge to design efficient topology-aware algorithms for collective operations. We also propose a communication model to analyze the communication costs involved in collective operations on large scale supercomputing systems. We have analyzed the performance characteristics of two collectives, MPI_Gather and MPI_Scatter on such systems and we have proposed topology-aware algorithms for these operations. Our experimental results have shown that the proposed algorithms can improve the performance of these collective operations by almost 54% at the micro-benchmark level.

Kandalla, Krishna; Subramoni, Hari; Vishnu, Abhinav; Panda, Dhabaleswar K.

2010-04-01T23:59:59.000Z

175

Voices for SSL Efficiency' Gather in Pasadena for Two-Day DOE Workshop  

Energy.gov (U.S. Department of Energy (DOE))

Over 100 attendees gathered in Pasadena, California, to participate in the "Voices for SSL Efficiency" DOE Solid-State Lighting Workshop on April 23-24, 2007. The workshop, hosted by DOE and Southern California Edison, was designed to initiate a dialogue on how Federal, State, and private-sector organizations can work together to guide market introduction of high efficiency, high-performance SSL products. Participants from energy efficiency organizations, utilities, government, and industry shared insights, ideas, and updates on the rapidly evolving SSL market.

176

Industry Leaders, Research Experts Gather for 2006 DOE Solid-State Lighting Workshop  

Energy.gov (U.S. Department of Energy (DOE))

Solid-state lighting (SSL) technology leaders from industry, research institutions, universities, and national laboratories gathered in Orlando, Florida from February 1-3, 2006 to attend a workshop focused on advancing SSL technologies from the laboratory to the marketplace. The workshop was hosted by the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (Building Technologies Office) and the Office of Science (Basic Energy Sciences Program). The 2006 workshop provided a forum for sharing updates on basic research underlying SSL technology, SSL core technology research, product development, commercialization support, and the ultimate goal of bringing energy-efficient, cost-competitive products to the market.

177

Data Gathering in Networks of Bacteria Colonies: Collective Sensing and Relaying Using Molecular Communication  

E-Print Network (OSTI)

The prospect of new biological and industrial applications that require communication in micro-scale, encourages research on the design of bio-compatible communication networks using networking primitives already available in nature. One of the most promising candidates for constructing such networks is to adapt and engineer specific types of bacteria that are capable of sensing, actuation, and above all, communication with each other. In this paper, we describe a new architecture for networks of bacteria to form a data collecting network, as in traditional sensor networks. The key to this architecture is the fact that the node in the network itself is a bacterial colony; as an individual bacterium (biological agent) is a tiny unreliable element with limited capabilities. We describe such a network under two different scenarios. We study the data gathering (sensing and multihop communication) scenario as in sensor networks followed by the consensus problem in a multi-node network. We will explain as to how th...

Einolghozati, Arash; Beirami, Ahmad; Fekri, Faramarz

2012-01-01T23:59:59.000Z

178

Small (5 million Btu/h) and large (300 million Btu/h) thermal test rigs for coal and coal slurry burner development  

SciTech Connect

NEI International Combustion Ltd. of Derby, England, now operates two thermal test rigs for the development of burners capable of handling coal-water slurries (CWS). A general description of the large rig and its capacity was given. Also, the necessary conversions of the equipment to handle CWS were described. Information on the properties of the CWS was included. This consisted of chemical analysis of the parent coal and the slurry, sieve analysis of a dry sample, and viscosity versus temperature data of the CWS. The process of design development of the burner was outlined. Ten illustrations were presented, including schematic diagrams of equipment and graphs of data.

Allen, J.W.; Beal, P.R.; Hufton, P.F.

1983-01-01T23:59:59.000Z

179

Type A Accident Investigation of the June 21, 2001, Drilling Rig Operator Injury at the Fermi National Accelerator Laboratory, August 2001  

Energy.gov (U.S. Department of Energy (DOE))

On June 21, 2001, at approximately 9:40 A.M., a construction sub-tier contractor employee (the “Operator”) at the Fermi National Accelerator Laboratory (Fermilab) received serious head injuries requiring hospitalization when he was struck by part of the drilling rig (a “tong”) that he was operating.

180

A Hardware-in-the-Loop Test Rig for Designing Near-Earth Aerial Robotics Vefa Narli and Paul Y. Oh  

E-Print Network (OSTI)

and build- ings. The lack of flight data and performance metrics poses a gap that prevents the analytical is a full-scale diorama of a near-Earth environment like forests. The rig is used to capture metrics adverse weather conditions and obscurants, like fog, rain or dust. A key gap in the knowledge domain

Oh, Paul

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Cost-Effective Reciprocating Engine Emissions Control and Monitoring for E&P Field and Gathering Engines  

SciTech Connect

This quarterly report discusses continuing work in the testing phase of the project that evaluates emission control technologies applied to a two-stroke cycle natural gas-fueled engine. In this phase, a one cylinder Ajax DP-115 (a 13.25 in bore x 16 in stroke, 360 rpm engine) is used to assess a sequential analysis and evaluation of a series of engine upgrades. As with most of the engines used in the natural gas industry, the Ajax engine is a mature engine with widespread usage throughout the gas gathering industry. The end point is an assessment of these technologies that assigns a cost per unit reduction in NO{sub x} emissions. This report describes potential emission reduction technologies, some of which have already been tested, and describes progress toward completing remaining tests to evaluate further synergies between some of the more promising technologies. While the end-goal is a closed-loop control system coupled with a low cost NO{sub x} retrofit package, additional work remains. Technologies including pre-combustion chambers, in-cylinder sensors, the means to adjust the air-to-fuel ratio, and modification of the air filter housing have been evaluated in previous reports. Current work focuses on preparing the test cell for tests using a 180 psig fuel valve. By using the Ajax DP-115 these tests are completed in a low-cost and efficient manner. The various technologies can be quickly exchanged with different hardware, and it is inexpensive to run the engine.

Sarah R. Nuss-Warren; Kirby S. Chapman

2005-12-01T23:59:59.000Z

182

Gathering Datasets for Activity Identification Lorcan Coyle, Juan Ye, Susan McKeever, Stephen Knox, Matthew Stabeler,  

E-Print Network (OSTI)

Gathering Datasets for Activity Identification Lorcan Coyle, Juan Ye, Susan McKeever, Stephen Knox is proceedings well, without publicly available datasets on which to compare results it is difficult to consolidate the disparate work being done. This prob- lem exists because realistic datasets describing human

Hammerton, James

183

Evolution of MDA-5/RIG-I-dependent innate immunity: Independent evolution by domain grafting  

Science Journals Connector (OSTI)

...proteins. Abbreviations: csp, caspase; cdf...Abbreviations: cdf, CARDif; csp, caspase. Solid black...mechanism that existed before plants and animals diverged . Mol Biol...Activation of the interferon system by short-interfering...RNA Helicases chemistry classification genetics Evolution...

Devanand Sarkar; Rob DeSalle; Paul B. Fisher

2008-01-01T23:59:59.000Z

184

Design and analysis of a composite flywheel preload loss test rig  

E-Print Network (OSTI)

process. Successful detection of the change in mass eccentricity was verified analytically through dynamic modeling of the flywheel rotor and magnetic suspension system. During steady state operation detection was determined to be feasible via...

Preuss, Jason Lee

2004-09-30T23:59:59.000Z

185

155The Great Gulf Oil Catastrophe of 2010 NASA's Terra satellite flew over the Deepwater Horizon rig's oil spill in the Gulf  

E-Print Network (OSTI)

rig's oil spill in the Gulf of Mexico on Saturday, May 1 and captured the above natural-color image of Mexico. NOAA's estimated release rate of oil spilling into the Gulf is 200,000 gallons per day since/meter 2 ? B) kg/meter 2 ? Problem 4 ­ The density of crude oil is about D=850 kg/m 3 . From your estimate

186

The design, implementation and testing of data gathering instrumentation for measurement of electromagnetic interference in electric power substations  

E-Print Network (OSTI)

THE DESIGN, IMPLEMENTATION AND TESTING OF DATA GATHERING INSTRUMENTATION FOR MEASUREMENT OF ELECTROMAGNETIC INTERFERENCE IN ELECTRIC POWER SUBSTATIONS A Thesis by GARY WAYNE GERLOFF Submitted to the Graduate College of Texas AAM University... IN ELECTRIC POWER SUBSTATIONS A Thesis by GARY WAYNE GERLOFF Approved as to style and content by: B. Don Russell (Chairman of Committee) A. K. A IM Sallie She p rd (Member) August 1983 ABSTRACT The Design, Implementation and Testing of Data...

Gerloff, Gary Wayne

2012-06-07T23:59:59.000Z

187

Design and fabrication of a bending rotation fatigue test rig for in situ electrochemical analysis during fatigue testing of NiTi shape memory alloy wires  

Science Journals Connector (OSTI)

The current investigation proposes a novel method for simultaneous assessment of the electrochemical and structural fatigue properties of nickel-titanium shape memory alloy (NiTi SMA) wires. The design and layout of an in situ electrochemical cell in a custom-made bending rotation fatigue (BRF) test rig is presented. This newly designed test rig allows performing a wide spectrum of experiments for studying the influence of fatigue on corrosion and vice versa. This can be achieved by performing ex situ and/or in situ measurements. The versatility of the combined electrochemical/mechanical test rig is demonstrated by studying the electrochemical behavior of NiTi SMA wires in 0.9% NaCl electrolyte under load. The ex situ measurements allow addressing various issues for example the influence of pre-fatigue on the localized corrosion resistance or the influence of hydrogen on fatigue life. Ex situ experiments showed that a pre-fatigued wire is more susceptible to localized corrosion. The synergetic effect can be concluded from the polarization studies and specifically from an in situ study of the open circuit potential (OCP) transients which sensitively react to the elementary repassivation events related to the local failure of the oxide layer. It can also be used as an indicator for identifying the onset of the fatigue failure.

Jenni Kristin Zglinski; Matthias Frotscher

2013-01-01T23:59:59.000Z

188

Design and fabrication of a bending rotation fatigue test rig for in situ electrochemical analysis during fatigue testing of NiTi shape memory alloy wires  

SciTech Connect

The current investigation proposes a novel method for simultaneous assessment of the electrochemical and structural fatigue properties of nickel-titanium shape memory alloy (NiTi SMA) wires. The design and layout of an in situ electrochemical cell in a custom-made bending rotation fatigue (BRF) test rig is presented. This newly designed test rig allows performing a wide spectrum of experiments for studying the influence of fatigue on corrosion and vice versa. This can be achieved by performing ex situ and/or in situ measurements. The versatility of the combined electrochemical/mechanical test rig is demonstrated by studying the electrochemical behavior of NiTi SMA wires in 0.9% NaCl electrolyte under load. The ex situ measurements allow addressing various issues, for example, the influence of pre-fatigue on the localized corrosion resistance, or the influence of hydrogen on fatigue life. Ex situ experiments showed that a pre-fatigued wire is more susceptible to localized corrosion. The synergetic effect can be concluded from the polarization studies and specifically from an in situ study of the open circuit potential (OCP) transients, which sensitively react to the elementary repassivation events related to the local failure of the oxide layer. It can also be used as an indicator for identifying the onset of the fatigue failure.

Neelakantan, Lakshman [Ruhr-Universitaet Bochum, Institute for Materials, 44801 Bochum (Germany); Department of Metallurgical and Materials Engineering, Indian Institute of Technology Madras, 600 036 Chennai (India); Zglinski, Jenni Kristin; Eggeler, Gunther [Ruhr-Universitaet Bochum, Institute for Materials, 44801 Bochum (Germany); Frotscher, Matthias [Ruhr-Universitaet Bochum, Institute for Materials, 44801 Bochum (Germany); CORTRONIK GmbH, 18119 Rostock-Warnemuende (Germany)

2013-03-15T23:59:59.000Z

189

Integrated rig for the production of boron nitride nanotubes via the pressurized vapor-condenser method  

DOE Patents (OSTI)

An integrated production apparatus for production of boron nitride nanotubes via the pressure vapor-condenser method. The apparatus comprises: a pressurized reaction chamber containing a continuously fed boron containing target having a boron target tip, a source of pressurized nitrogen and a moving belt condenser apparatus; a hutch chamber proximate the pressurized reaction chamber containing a target feed system and a laser beam and optics.

Smith, Michael W; Jordan, Kevin C

2014-03-25T23:59:59.000Z

190

Design, fabrication and testing of a bearing test rig and preliminary studies on oil mist lubrication  

E-Print Network (OSTI)

three microns in diameter. The oil mist generated by the mist generator can be conveyed up to 500 ft. through pipes, also known as main headers at velocities up to 22 fps. (2, 3). The turbulence induced by higher velocities causes coalescence... at the bottom of the pipe. In order to prevent clogging of the smaller distribution pipes or reclassifiers with oil, the main header system is This thesis follows the form and style of STLE journal, i i n n in rin sloped back toward the generator so...

Shamim, Abdus

2012-06-07T23:59:59.000Z

191

Classification of sags gathered in distribution substations based on multiway principal component analysis  

Science Journals Connector (OSTI)

Voltage sags, whether they occur in transmission or distribution systems, may severely damage the loads connected to the power system. As these problems could cost a great deal financially, electric utilities are very interested in finding the origins of sags, that is, whether they have been originated in the transmission network (high voltage (HV)) or in the distribution system (medium voltage (MV)). In addition to the needs of utilities and regulators, many researchers have been prompted to develop reliable methods to properly classify sags. Several of these methods, based on classifying meaningful features extracted from data and waveforms, have been proposed in the literature. Unlike those methods, though, we propose a systematic transformation of data, based on multiway principal component analysis (MPCA), to develop a new voltage sag classification procedure. Sampled voltage and current waveforms of previously registered sags are used together with the MPCA technique to obtain a lower dimensional model. This model is then used to project new sags and classify them according to their origin in the power system. Different classification criteria and parameters are examined to maximize the classification rates of not yet seen sags. Applying the proposed method to real sags recorded in substations demonstrates its applicability and power.

Abbas Khosravi; Joaquim Meléndez; Joan Colomer

2009-01-01T23:59:59.000Z

192

Energy Efficient Model for Data Gathering in Structured Multiclustered Wireless Sensor Networks  

E-Print Network (OSTI)

constrained sensor nodes as the replacement of battery is a major issue in an application like power monitoring systems. 1 Introduction Advances in VLSI technology have enabled the development of low, and limited storage, have to be taken into considerations when deploying large sensor net- works

193

Personas in the middle: automated support for creating personas as focal points in feature gathering forums  

Science Journals Connector (OSTI)

Many software systems utilize forums to allow a broad set of stakeholders to request features. However the resulting mass of ideas and comments can make prioritization and management of feature requests challenging. In this paper we propose a novel approach ... Keywords: persona, requirements management, text mining

Mona Rahimi, Jane Cleland-Huang

2014-09-01T23:59:59.000Z

194

Course helps professionals develop watershed protection plans: Texas water resources professionals gather  

E-Print Network (OSTI)

tx H2O | pg. 6 Story by Ric Jensen Course helps professionals develop watershed protection plans | pg. 6 tx H2O | pg. 7 W ater resources professionals wanting training on watershed protection plan development are benefiting from a course... AgriLife Research, the River Systems Institute at Texas State University, Texas Institute for Applied Environmental Research at Tarleton State University, and the U.S. Environmental Protection Agency (EPA) to create the Texas Watershed Planning...

Jensen, Ric

2008-01-01T23:59:59.000Z

195

Balinese Y-Chromosome Perspective on the Peopling of Indonesia: Genetic Contributions from Pre-Neolithic Hunter- Gatherers, Austronesian Farmers, and Indian Traders  

E-Print Network (OSTI)

The island of Bali lies near the center of the southern chain of islands in the Indonesian archipelago, which served as a stepping-stone for early migrations of hunter-gatherers to Melanesia and Australia and for more ...

Karafet, Tatiana M.; Lansing, J. Stephen; Redd, Alan J.; Reznikova, Svetlana; Watkins, Joseph C.; Surata, S. P. K; Arthawiguna, W. A.; Mayer, Laura; Bamshad, Michael; Jorde, Lynn B.; Hammer, Michael F.

2005-02-01T23:59:59.000Z

196

Backgrounder: Geothermal resource production, steam gathering, and power generation at Salton Sea Unit 3, Calipatria, California  

SciTech Connect

The 10,000-kilowatt Salton Sea Unit 1 power plant was designed to demonstrate that electrical power generation, using the highly saline brines from the Salton Sea geothermal reservoir, was technically and economically feasible. Unit 1, owned by Earth Energy, a Unocal subsidiary, began operating in 1982, initiating an intensive testing program which established the design criteria necessary to construct the larger 47,500-kilowatt Unit 3 power plant, unit 3 contains many of the proprietary or patented technological innovations developed during this program. Design, construction and start-up of the Unit 3 power generating facility began in December, 1986, and was completed in 26 months. By the end of 1988, the brine handling system was in full operation, and the turbine had been tested at design speed. Desert Power Company, a Unocal subsidiary, owns the power generating facility. Unocal owns the brine resource production facility. Power is transmitted by the Imperial Irrigation District to Southern California Edison Company.

None

1989-04-01T23:59:59.000Z

197

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CHAPTER 9 MOBILE CRANES 9-i This chapter specifies operation, inspection, maintenance, and testing requirements for the use of mobile cranes and implements the requirements of ASME B30.5 ("Mobile and Locomotive Cranes") (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 9.1 GENERAL .................................................................................................................................9-1 9.1.1 Operator Training/Qualification ..................................................................................9-1 9.1.2 Load Limits..................................................................................................................9-1 9.1.3 Load Rating Chart........................................................................................................9-1

198

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Change Notice No. 1 DOE-STD-1090-2007 Change Notice No. 1 DOE-STD-1090-2007 December 2007 Chapter 4 Provide ASME attribution at introduction to the Table on Contents and on Figures 4-3,4 and Exhibits 1 & 2 Chapter 7 Provide ASME attribution at introduction to the Table on Contents and on Figures 7-1,2,3,4,5 and Table 7-1 Chapter 8 Provide ASME attribution at introduction to the Table on Contents and on Figures 8-1,2,3,4,5,6,7,8,9 and Table 8-1 Chapter 9 Provide ASME attribution at introduction to the Table on Contents and on Figures 9-1,2,3,4,5,6 and Table 9-2 Chapter 11 Provide ASME attribution at introduction to the Table on Contents and on Figures 11-10,15 and Tables 11-10,11,14,15,16 Chapter 12 Provide ASME attribution at introduction to the Table on Contents and on

199

rig upgrades2.qxp  

NLE Websites -- All DOE Office Websites (Extended Search)

T R A P E D O F E N E R G Y E T A T S D E T I N U S O F A M E R I C A E A s the oil and gas industry continues to drill in more remote areas, at deeper depths, and in more...

200

Hunter-Gatherers Today  

Science Journals Connector (OSTI)

...Atomic and Molecular Physics. Vol. 14. D. R. Bates and Benjamin Bederson, Eds. Academic Press, New York, 1978. xii, 464...Science and Tech-nology. Vol. 11. Ernest J. Henley, Jeffery Le-wins, and Martin Becker, Eds. Plenum, New York, 1979...

NANCY HOWELL

1979-09-14T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

User Requirements Gathered for  

NLE Websites -- All DOE Office Websites (Extended Search)

Workshops to derive and document each DOE SC Office's HPC requirements for NERSC in 2013-14" * Deliverables: Reports that includes both the HPC requirements and supporting...

202

Gathering Interstellar Gas  

Science Journals Connector (OSTI)

...pressure of the solar wind and the inward pressure...heliosphere encounters a mass equivalent to Mount...heliosphere—a lower velocity brings into question...that can be used with the map of the interstellar gas...strength of its stellar wind. As we explore the diverse...

Seth Redfield

2012-06-08T23:59:59.000Z

203

Cost-Effective Reciprocating Engine Emissions Control and Monitoring for E&P Field and Gathering Engines  

SciTech Connect

Continuing work in controlled testing uses a one cylinder Ajax DP-115 (a 13.25 in bore x 16 in stroke, 360 rpm engine) to assess a sequential analysis and evaluation of a series of engine upgrades. As with most of the engines used in the natural gas industry, the Ajax engine is a mature engine with widespread usage throughout the gas gathering industry. The end point is an assessment of these technologies that assigns a cost per unit reduction in NOX emissions. Technologies including one pre-combustion chamber, in-cylinder sensors, the means to adjust the air-to-fuel ratio, and modification of the air filter housing have been evaluated in previous reports. Current work focuses on final preparations for testing pre-combustion chambers with different characteristics and using mid-to-high-pressure fuel valves and initial runs of these tests. By using the Ajax DP-115 these tests are completed in a low-cost and efficient manner. The various technologies can be quickly exchanged with different hardware, and it is inexpensive to run the engine. Progress in moving toward field testing is discussed, and changes to the first planned field test are presented. Although changes have been made to the previous plan, it is expected that several new sites will be selected soon. Field tests will begin in the next quarter.

Kirby S. Chapman; Sarah R. Nuss-Warren

2006-07-01T23:59:59.000Z

204

Radiologoical Conditions on Rongelap Atoll: Recommendations for Visiting and Food Gathering on the Norhtern Islands of Rongelap Atoll  

SciTech Connect

Rongelap Atoll experienced close-in or local fallout from the U.S. nuclear test program conducted in the northern Marshall Islands between 1946 and 1958. By all internationally agreed scientific criteria, Rongelap Island is considered safe for permanent resettlement. However, the amount of bomb-related radioactivity in soil and vegetation is, on average, about 5 times greater in the northern islands of the atoll because the centerline of the fallout pattern from the 1954 thermonuclear ''Bravo'' test extended over this part of the atoll. The most important radioactive element remaining on the atoll is radioactive cesium (cesium-137). Cesium-137 emits what is called a ''gamma ray'' that can penetrate the body and deliver both an external (outside the body) and internal (from inside the body) gamma dose to inhabitants of Rongelap Atoll. Cesium-137 is taken up from the soil into locally grown foodstuffs such as coconut, Pandanus and breadfruit. Significant quantities of cesium-137 may also be found in coconut crab. The internal dose delivered to people eating these products will be directly proportional to the concentration of cesium-137 in the food and the amount consumed. The external gamma dose will depend on the concentration of cesium-137 in the soil and the amount of time spent in the area. The highest concentration of cesium-137 in surface soils of the northern islands of Rongelap Atoll is about equivalent to that measured on Bikini Island. Under the radiation protection criteria adopted by the Republic of the Marshall Islands Nuclear Claims Tribunal, permanent resettlement of these islands would require intervention because of the higher radiation doses that could potentially be delivered to inhabitants living on a diet derived largely from local foods. A more realistic lifestyle scenario is that the resettled population on Rongelap Island will occasionally visit the northern part of the atoll for food gathering, fishing and other recreational activities. It is estimated that a person spending 8 hours (1 work day) in the interior of the Rongelap Atoll northern islands will receive a maximum additional external dose of around 0.1-0.2 mrem per day. Furthermore, Lawrence Livermore National Laboratory's environmental monitoring continues to show that the marine environment contains very low levels of bomb radioactivity. Similarly, the occasional consumption of terrestrial foods including coconut crab from the northern islands is not expected to add significantly to the radiological health risk of living on Rongelap Island. The average annual effective ingestion dose for Rongelap Island resettlement in 2002 is estimated to be around 1-2 mrem per year when imported foods are made available and proposed remediation efforts take effect. This estimate is about twice that of the Rongelap Island resettlement worker population using direct measurements from the whole body counting program. Resettlement workers presently living on the islands receive an average internal dose from cesium-137 of less than 1 mrem (0.01 mSv) per year. These workers are known to eat locally grown foods and coconut crabs collected from the northern islands. The highest individual dose observed was 4 mrem (0.04 mSv) per year. Under the guidelines adopted by the Republic of the Marshall Islands Nuclear Claims Tribunal, it is concluded that diving, fishing and visiting any northern island of Rongelap Atoll are safe activities for limited periods. Eating local fish and other marine life such as clams would also be considered safe. Consumption of plant foods from the northern islands of Rongelap Atoll depends on successful implementation of specific remediation measures to ensure dietary intakes of cesium-137 remain at or below levels considered safe. The whole body counting program should continue to monitor the actual internal levels of cesium-137 among people eating plants and coconut crabs gathered from the northern islands of Rongelap Atoll islands until such time that the Nuclear Claims Tribunal guidelines are met.

Hamliton, T F

2003-02-01T23:59:59.000Z

205

Appendix 3-1-Reflections on the data collection and modeling process In this document I briefly discuss the process used for data gathering, model building,  

E-Print Network (OSTI)

discuss the process used for data gathering, model building, and model analysis that I employed. Therefore I leave the comprehensive description of the qualitative research process and model building generation - July 2004: building a qualitative model - August 2004: Building a detailed simulation model

Rahmandad, Hazhir

206

A Low-Cost Continuous Emissions Monitoring System for Mobile and Stationary Engine SCR/DPF Applications/Data-Logger for Vehicle Data Acquisition  

Energy.gov (U.S. Department of Energy (DOE))

This project describes a novel system of sensors that continuously monitor emissions in real time and a data logger to gather real-time data from a vehicle

207

Provisioning offspring and others: risk–energy trade-offs and gender differences in hunter–gatherer foraging strategies  

Science Journals Connector (OSTI)

...resources that minimize risk or maximize energy will...greater benefits from investments in direct offspring...opportunities forgone) from investments in social provisioning...individuals solve the risk-energy trade-off...cooperative caretaking, political systems, marriage patterns...

2011-01-01T23:59:59.000Z

208

Investigation on multi-variable decoupled temperature control system for enamelling machine with heated air circulation  

SciTech Connect

A lots of problems may occur frequently when controlling the temperature of the enamelling machine oven in the real industrial process, such as multi-variable coupled problem. an experimental rig with triple inputs and triple outputs was devised and a simulation modeling was established accordingly in this study,. the temperature control system based on the feedforward compensation algorithm was proposed. Experimental results have shown that the system is of high efficiency, good stability and promising application.

Li, Yang; Qin, Le; Zou, Shipeng; Long, Shijun [School of Information Engineering, Guangdong University of Technology, Guangzhou, 510006 (China)

2014-04-11T23:59:59.000Z

209

Build a Floating Oil Rig  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of the Interior's Minerals Management Service developed this teacher's guide about the many energy resources found in, over, and under the ocean. Includes sections on petroleum,...

210

Deep Drilling Basic Research: Volume 4 - System Description. Final Report, November 1988--August 1990  

SciTech Connect

The first section of this Volume will discuss the ''Conventional Drilling System''. Today's complex arrangement of numerous interacting systems has slowly evolved from the very simple cable tool rigs used in the late 1800s. Improvements to the conventional drilling rig have varied in size and impact over the years, but the majority of them have been evolutionary modifications. Each individual change or improvement of this type does not have significant impact on drilling efficiency and economics. However, the change is almost certain to succeed, and over time--as the number of evolutionary changes to the system begin to add up--improvements in efficiency and economics can be seen. Some modifications, defined and described in this Volume as Advanced Modifications, have more than just an evolutionary effect on the conventional drilling system. Although the distinction is subtle, there are several examples of incorporated advancements that have had significantly more impact on drilling procedures than would a truly evolutionary improvement. An example of an advanced modification occurred in the late 1970s with the introduction of Polycrystalline Diamond Compact (PDC) drill bits. PDC bits resulted in a fundamental advancement in drilling procedures that could not have been accomplished by an evolutionary improvement in materials metallurgy, for example. The last drilling techniques discussed in this Volume are the ''Novel Drilling Systems''. The extent to which some of these systems have been developed varies from actually being tested in the field, to being no more than a theoretical concept. However, they all have one thing in common--their methods of rock destruction are fundamentally different from conventional drilling techniques. When a novel drilling system is introduced, it is a revolutionary modification of accepted drilling procedures and will completely replace current techniques. The most prominent example of a revolutionary modification in recent history was the complete displacement of cable tool rigs by rotary drilling rigs in the late 1920s.

Anderson, E.E.; Maurer, W.C.; Hood, M.; Cooper, G.; Cook, N.

1990-06-01T23:59:59.000Z

211

ARM - Data Gathering and Delivery  

NLE Websites -- All DOE Office Websites (Extended Search)

National Laboratory, acquires additional data from other sources, such as National Weather Service satellite and surface data. Most of the ARM data are distributed in netCDF...

212

Blow out preventer handling system  

SciTech Connect

A system for testing and installing a blow out preventer on a floating vessel and offshore drilling rigs, although the system may be used on other rotary drilling rigs, is disclosed. Retractable rotary table supporting beams are disposed over the moon pool and the rotary table is releasably connected to them. Retractable sub-structure beams are provided below the rotary table so that means provided to move the assembled blow out preventer can move it through an opening in the derrick and over the moon pool when the rotary beams are retracted. Retractable moon pool skid beams are provided which support the blow out preventer when skidded through the moon pool opening in the substructure. In one aspect of the invention, the means connecting the rotary table to its support beams are self-aligning to that once the rotary table is aligned it can be removed and replaced without any further alignment. Also, support shoulders are provided on the main blow out preventer and lower riser section thereof which engage and are supported by the moon pool beams, so that the rotary support beams, rotary table and sub-structure support beams can be replaced and the blow out preventer hooked up to the riser, drill string or casing, the moon pool beams retracted and the blow out preventer lowered in the moon pool to the sea floor.

Guinn, D.C.; Haggard, A.K.; Thomas, J.P.

1980-10-28T23:59:59.000Z

213

Applying simulation experience design methods to creating serious game-based adaptive training systems  

Science Journals Connector (OSTI)

......environments, adaptive community-based intranets, and intercultural agent-based systems...identify the needs, objectives, and characteristics of a single user in a scenario, and...due to dynamic organizational changes characteristics of many training environments, gathering......

Elaine M. Raybourn

2007-03-01T23:59:59.000Z

214

Soft torque rotary system reduces drillstring failures  

SciTech Connect

This paper reports that the use of the soft torque system has significantly reduced torque fluctuations (up to 80%), torsional drillstring vibrations, and bit slip-stick conditions to help reduce drillstring failures and improve penetration rates in deep directional wells. The system was instrumental in eliminating expensive ($5-10 million) drillstring failures on Well SL 531 No. 3, a complex directional well in Mobile Bay. The soft torque rotary system attenuates and interrupts the torsional oscillations of the drillstring and thus prevents the buildup of energy in torsional waves that are reflected back and forth between the bit and the rotary table. The soft torque rotary system can be installed on any rig equipped with an independent electronically driven rotary table or top drive. The system is relatively inexpensive and easy to install.

Javanmardi, K.; Gaspard, D. (Shell Offshore Inc., New Orleans, LA (United States))

1992-10-12T23:59:59.000Z

215

Experimental study on the model of the correlation between the movement of the drilling string with big diameter of drill and effects on the oil rigs  

Science Journals Connector (OSTI)

In the author’s view, an important contribution is to clarify the interaction of a drill string and unconventional hoisting system, we find the influence of the constructive peculiarities oil installations (drilling

Marius Stan; Lazar Avram

2014-08-01T23:59:59.000Z

216

Computer Systems to Oil Pipeline Transporting  

E-Print Network (OSTI)

Computer systems in the pipeline oil transporting that the greatest amount of data can be gathered, analyzed and acted upon in the shortest amount of time. Most operators now have some form of computer based monitoring system employing either commercially available or custom developed software to run the system. This paper presented the SCADA systems to oil pipeline in concordance to the Romanian environmental reglementations.

Chis, Timur

2009-01-01T23:59:59.000Z

217

An advanced geothermal drilling system: Component options and limitations  

SciTech Connect

The historical developments of drilling technology for geothermal resources have followed traditional incremental trends. The local expertise and rigs were adapted from existing drill rigs used for mining, civil, and water well projects. In areas with hydrocarbon resources, petroleum drilling hardware has been adapted; and in other countries, these units were imported as depth requirements increased and more robust derricks and downhole tools were needed. This ad hoc approach has provided adequate exploration and production wells. In contrast to the incremental improvements in petroleum rotary drilling system components this paper reviews a new, purpose-developed system that would solve the known major problems by design. Performance goals of 4 km (12,000 ft.) depth, 400 C, (750 F) and penetration rates greater than 8 m/h (25 ft/h) were selected. This advanced system was reviewed extensively and estimates of perhaps 30 to 60% cost savings were projected, depending on the assumed effectiveness and performance improvements provided. This paper continues the design and feasibility study and presents some of the component and sub-system details developed thus far.

Rowley, J. [Pajarito Enterprises, Los Alamos, NM (United States); Saito, Seiji [JMC Geothermal Division, Tokyo (Japan); Long, R.C. [Department of Energy, Las Vegas, NV (United States). Yucca Mountain Site Characterization Project

1995-12-31T23:59:59.000Z

218

ASBESTOS PIPE-INSULATION REMOVAL ROBOT SYSTEM  

SciTech Connect

This final topical report details the development, experimentation and field-testing activities for a robotic asbestos pipe-insulation removal robot system developed for use within the DOE's weapon complex as part of their ER and WM program, as well as in industrial abatement. The engineering development, regulatory compliance, cost-benefit and field-trial experiences gathered through this program are summarized.

Unknown

2000-09-15T23:59:59.000Z

219

24th Benelux Meeting Systems and Control  

E-Print Network (OSTI)

applied on a half-car test rig.30­14.55 Contribution to the control of a rotary cement kiln - A simu- lation . . . . . . . . . . . . . . . . . . . . . . . . . . .

Serdijn, Wouter A.

220

SOLERAS - Photovoltaic Power Systems Project. Rural solar applications. Final report: project summary  

SciTech Connect

The Saudi Solar Village Project photovoltaic system is described, consisting of 160 arrays, a computerized control system, 1100 kW of electrical storage in lead-acid batteries, and an automatic weather data gathering system. Satisfactory overall system performance is reported. Performance degradation due to dust on the array lenses was determined. Field operational problems are discussed. (LEW)

Not Available

1985-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Collision Detection System Andrew Boissonnault, Akilesh Krishnamurthy Daiheng Ni, Russell Tessier  

E-Print Network (OSTI)

and of the Civil Engineering Department is working to develop a vehicle collision detection system. The systemCollision Detection System Andrew Boissonnault, Akilesh Krishnamurthy Daiheng Ni, Russell Tessier that would be mounted on the front of the vehicle. This system will gather information from all

Mountziaris, T. J.

222

Potential impacts of artificial intelligence expert systems on geothermal well drilling costs:  

SciTech Connect

The Geothermal research Program of the US Department of Energy (DOE) has as one of its goals to reduce the cost of drilling geothermal wells by 25 percent. To attain this goal, DOE continuously evaluates new technologies to determine their potential in contributing to the Program. One such technology is artifical intelligence (AI), a branch of computer science that, in recent years, has begun to impact the marketplace in a number of fields. Expert systems techniques can (and in some cases, already have) been applied to develop computer-based ''advisors'' to assist drilling personnel in areas such as designing mud systems, casing plans, and cement programs, optimizing drill bit selection and bottom hole asssembly (BHA) design, and alleviating lost circulation, stuck pipe, fishing, and cement problems. Intelligent machines with sensor and/or robotic directly linked to AI systems, have potential applications in areas of bit control, rig hydraulics, pipe handling, and pipe inspection. Using a well costing spreadsheet, the potential savings that could be attributed to each of these systems was calculated for three base cases: a dry steam well at The Geysers, a medium-depth Imerial Valley well, and a deep Imperial Valley well. Based on the average potential savings to be realized, expert systems for handling lost circulations problems and for BHA design are the most likely to produce significant results. Automated bit control and rig hydraulics also exhibit high potential savings, but these savings are extremely sensitive to the assumptions of improved drilling efficiency and the cost of these sytems at the rig. 50 refs., 19 figs., 17 tabs.

Satrape, J.V.

1987-11-24T23:59:59.000Z

223

Achieve Continuous Injection of Solid Fuels into Advanced Combustion System Pressures  

SciTech Connect

The overall objective of this project is the development of a mechanical rotary-disk feeder, known as the Stamet Posimetric High Pressure Solids Feeder System, to demonstrate feeding of dry granular coal continuously and controllably into pressurized environments of up to 70 kg/cm2 (1,000 psi). This is the Phase III of the ongoing program. Earlier Phases 1 and II successfully demonstrated feeding into pressures up to 35 kg/cm{sup 2} (500 psi). The final report for those phases was submitted in April 2005. Based on the previous work done in Phases I & II using Powder River Basin coal provided by the PSDF facility in Wilsonville, AL, a Phase III feeder system was designed and built to accomplish the target of feeding the coal into a pressure of 70 kg/cm2 (1,000 psi) and to be capable of feed rates of up to 550 kilograms (1,200lbs) per hour. The drive motor system from Phase II was retained for use on Phase III since projected performance calculations indicated it should be capable of driving the Phase III pump to the target levels. The pump & motor system was installed in a custom built test rig comprising an inlet vessel containing an active live-wall hopper mounted on weigh cells in a support frame, transition into the pump inlet, transition from pump outlet and a receiver vessel containing a receiver drum supported on weigh cells. All pressure containment on the rig was rated to105 kg/cm{sup 2} (1,500psi) to accommodate the final pressure requirement of a proposed Phase IV of the program. A screw conveyor and batch hopper were added to transfer coal at atmospheric pressure from the shop floor up into the test rig to enable continuous feeding up to the capacity of the receiving vessel. Control & monitoring systems were up-rated from the Phase II system to cover the additional features incorporated in the Phase III rig, and provide closer control and expanded monitoring of the entire system. A program of testing and modification was carried out in Stamet's facility in CA, culminating in the first successful feeding of coal into the Phase III target of 70 kg/cm{sup 2} (1,000 psi) gas pressure in March 2007. Subsequently, repeated runs at pressure were achieved, and comparison of the data with Phase II results when adjusted for scale differences showed further power reductions of 40% had been achieved from the final Phase II pressure runs. The general design layout of a commercial-scale unit was conducted, and preliminary cost estimates made.

Derek L. Aldred; Timothy Saunders

2007-03-31T23:59:59.000Z

224

Mexico's Energy Reform and the Potential Impact on Texas' Transportation System  

E-Print Network (OSTI)

preparation ­ Heavy bulldozers and dump trucks to build road to serve pad site · Move rotary rig to pad site;Transportation and Well Development · Five-step well development process: ­ Site preparation ­ Rigging up ­ Drilling ­ Hydraulic fracturing ­ Rigging down #12;Transportation and Well Development · Initial site

225

Human rigHts advocacy in action  

E-Print Network (OSTI)

in memoriam 26 2 nonesuch//Autumn 2011 Greencoat 80 Silk is carbon balanced ­ where the carbon intensity has purchased. Carbon balancing by the World Land Trust tackles climate change through projects that both offset 18 Brave new world 22 thought that counts 27 In pictures snapshots 5 taken 29 Regulars Bristol

Bristol, University of

226

The Five Offshore Drilling Rig Markets  

Science Journals Connector (OSTI)

Market valuations are performed by a number of industry consultancies (e.g. Douglas-Westwood, GBI Research, IHS, R.S. Platou, Rystad Energy, Wood Mackenzie). Comparisons across firms depend...7, 18]. Large market...

Mark J. Kaiser; Brian F. Snyder

2013-01-01T23:59:59.000Z

227

Hoisting and Rigging Technical Advisory Committee Membership...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Isaac DOE, Los Alamos Site Office imvaldez@doeal.gov (505) 664-0285 Viola, Michael Princeton Plasma Physics Lab mviola@pppl.gov (609) 243-3655 Wang, Y. T NNSA, Livermore...

228

Force control system design for aerodynamic load simulator  

Science Journals Connector (OSTI)

A dynamic load simulator which can reproduce on-ground the aerodynamic hinge moment of control surface is an essential rig for the performance and stability test of an aircraft actuation system. The hinge moment varies widely over the flight envelope depending on the specific flight condition and maneuvering status. To replicate the wide spectrum of this hinge moment variation within some accuracy bounds, a force controller is designed based on the quantitative feedback theory (QFT). A dynamic model of load actuation system is derived, and verified through the experiment. The efficacy of QFT force controller is verified by a numerical simulation, in which combined aircraft dynamics, flight control law and hydraulic actuation system dynamics of aircraft control surface are considered.

Yoonsu Nam; Sung Kyung Hong

2002-01-01T23:59:59.000Z

229

Gathering Data to Assess Your Watershed  

E-Print Network (OSTI)

Quality Data Recycling Programs Economic Development Census Data & Demographics Tax Records #12 and Wastewater Planning and Assessments Population Projections TNRIS Data from State Agencies Railroad Commission

230

Gathering Data to Assess Your Watershed  

E-Print Network (OSTI)

Environmental Depts. Water Quality Data Recycling Programs Economic Development Census Data & Demographics Tax Water and Wastewater Planning and Assessments Population Projections Railroad Commission (RRC) Oil

231

Interactive physical agents for story gathering  

E-Print Network (OSTI)

Robots are typically thought of as autonomous devices which require little to no human interaction to complete their goals. In this study we investigated what would happen if the success of a robot was contingent upon its ...

Reben, Alexander James

2010-01-01T23:59:59.000Z

232

Information Gathering Session Gillian Charles & Ken Dragoon  

E-Print Network (OSTI)

and associated technologies. ­ Hydropower upgrades, new hydropower projects 3 Purpose Develop a hydro supply curve to determine the hydropower development potential in the NW region ­ Council's Seventh Power Plan-effectiveness Quantity-MWh Price - $/MWh 4 #12;3/27/2012 3 Hydro Assessment: 1980's National Hydropower Survey Hydro Site

233

Introduction People have gathered Rangia and  

E-Print Network (OSTI)

, Veracruz, Tabasco, and Campeche during 2004 and 2005. Distribution, Biology, and Ecology Rangia cuneata

234

RED: a Rich Epinions Dataset for Recommender Systems Simon Meyffret1,2  

E-Print Network (OSTI)

RED: a Rich Epinions Dataset for Recommender Systems Simon Meyffret1,2 , Emmanuel Guillot1}@liris.cnrs.fr ABSTRACT Recommender Systems require specific datasets to evaluate their approach. They do not require is not gathered in today datasets. In this paper, we provide a dataset containing reviews from users on items

Paris-Sud XI, Université de

235

Advanced Mud System for Microhole Coiled Tubing Drilling  

SciTech Connect

An advanced mud system was designed and key components were built that augment a coiled tubing drilling (CTD) rig that is designed specifically to drill microholes (less than 4-inch diameter) with advanced drilling techniques. The mud system was tailored to the hydraulics of the hole geometries and rig characteristics required for microholes and is capable of mixing and circulating mud and removing solids while being self contained and having zero discharge capability. Key components of this system are two modified triplex mud pumps (High Pressure Slurry Pumps) for advanced Abrasive Slurry Jetting (ASJ) and a modified Gas-Liquid-Solid (GLS) Separator for well control, flow return and initial processing. The system developed also includes an additional component of an advanced version of ASJ which allows cutting through most all materials encountered in oil and gas wells including steel, cement, and all rock types. It includes new fluids and new ASJ nozzles. The jetting mechanism does not require rotation of the bottom hole assembly or drill string, which is essential for use with Coiled Tubing (CT). It also has low reactive forces acting on the CT and generates cuttings small enough to be easily cleaned from the well bore, which is important in horizontal drilling. These cutting and mud processing components and capabilities compliment the concepts put forth by DOE for microhole coiled tubing drilling (MHTCTD) and should help insure the reality of drilling small diameter holes quickly and inexpensively with a minimal environmental footprint and that is efficient, compact and portable. Other components (site liners, sump and transfer pumps, stacked shakers, filter membranes, etc.. ) of the overall mud system were identified as readily available in industry and will not be purchased until we are ready to drill a specific well.

Kenneth Oglesby

2008-12-01T23:59:59.000Z

236

Automated Surface Observing System: Standby Power Options  

NLE Websites -- All DOE Office Websites (Extended Search)

Automated Automated Surface Observing System Standby Options Power Automated Surface Observing System (ASOS) General System Description * Self contained group of sensors and data gathering equipment that produces an automated weather observation * Weather observations support aviation, climate data, non government weather operations, public consumption, etc. * Initial deployment began in 1991 and continued through 1997 * Located at 884 sites nationwide, normally at airports * System has two distinct subsystems: Field installed equipment (DCP & Sensor Group) and an indoor processor (ACU) with peripherals * Separate facility power for DCP & Sensors and ACU 1 * measure and collect data * Located on the airport * back up group for 10 minutes * Currently pl

237

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 PERSONNEL QUALIFICATION AND TRAINING 6-i Chapter 6 Personnel Qualification and Training This chapter describes personnel qualification and training. Only qualified personnel shall operate the equipment covered in this standard. 6.1 GENERAL ................................................................................................................................6-1 6.2 QUALIFICATION...................................................................................................................6-2 6.2.1 General.........................................................................................................................6-2 6.2.2 Operators of Cab-Operated and Pulpit-Operated Cranes .............................................6-2

238

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 FORKLIFT TRUCKS 10-i Chapter 10 Forklift Trucks This chapter specifies operation, inspection, testing, and maintenance requirements for forklift trucks powered by internal-combustion engines or electric motors and implements the requirements of ASME B56.1 ("Safety Standard for powered Industrial Trucks - Low Lift and High lift Trucks") and B56.6 ("Rough Terrain Fork Lift Trucks"), and ANSI/UL 558 ("Internal-Combustion-Engine-Powered Industrial Trucks") and 583 ("Electric-Battery-Powered Industrial Trucks"). 10.1 GENERAL ...............................................................................................................................10-1 10.1.1 Operator Training/Qualification ................................................................................10-1

239

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

019-2004 019-2004 CHAPTER 16 MISCELLANEOUS LIFTING DEVICES 16-i Chapter 16 Miscellaneous Lifting Devices This chapter provides safety standards designated to sign verify, based on personal observations, certified records, or direct reports, that a specific action has been performed in accordance with specified requirements. For the operation, inspection, testing, and maintenance for miscellaneous lifting devices, (truck mounted cranes - capacity 1 ton or less not covered in ASME B30.5 ("Mobile and Locomotive Cranes") and implements the requirements of ASME PALD ("Portable Automotive Lifting Devices") for self contained shop cranes. 16.1 GENERAL ..................................................................................................................................

240

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 PERSONNEL QUALIFICATION AND TRAINING 6-i Chapter 6 Personnel Qualification and Training This chapter describes personnel qualification and training. Only qualified personnel shall operate the equipment covered in this standard. 6.1 GENERAL................................................................................................................................6-1 6.2 QUALIFICATION...................................................................................................................6-2 6.2.1 General.........................................................................................................................6-2 6.2.2 Operators of Cap-Operated and Pulpit-Operated Cranes .............................................6-2

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DEFINITIONS DEFINITIONS ................................................. 1-1 CHAPTER 2 CRITICAL LIFTS................................................................................. 2-1 2.1 CRITICAL-LIFT DETERMINATION........................................................ 2-1 2.2 CRITIAL-LIFT REQUIREMENTS............................................................. 2-2 CHAPTER 3 PREENGINEERED PRODUCTION LIFTS................................3-1 3.1 GENERAL....................................................................................................... 3-1 3.2 OPERATION EVALUATION ...................................................................... 3-2 3.2.1 Load Identification................................................................................

242

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 FORKLIFT TRUCKS 10-i This chapter specifies operation, inspection, testing, and maintenance requirements for forklift trucks powered by internal-combustion engines or electric motors and implements the requirements of ANSI/ITSDF B56.1 ("Safety Standard for powered Industrial Trucks - Low Lift and High lift Trucks") and ANSI/ITSDF B56.6 ("Rough Terrain Fork Lift Trucks"), and ANSI/UL 558 ("Internal-Combustion- Engine-Powered Industrial Trucks") and ANSI/UL 583 ("Electric-Battery-Powered Industrial Trucks"). 10.1 GENERAL ...............................................................................................................................10-1 10.1.1 Operator Training/Qualification ................................................................................10-1

243

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 PREENGINEERED PRODUCTION LIFTS 3-i Chapter 3 Preengineered Production Lifts This chapter provides requirements for the design, evaluation, and performance of preengineered production lifts. This lift designation may be used at the discretion of the contractor for selected operations. 3.1 GENERAL................................................................................................................................3-1 3.2 OPERATION EVALUATION................................................................................................3-2 3.2.1 Load Identification.......................................................................................................3-2 3.2.2 Task Determination......................................................................................................3-2

244

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 REFERENCES 17-1 Chapter 17 References American Institute of Steel Construction AISC Specifications for the design, fabrication, and erection of structural steel for buildings. American Iron and Steel Institute AISI Standards for Type-302 or Type-304 stainless steel. American National Standards Institute and the American Society of Mechanical Engineers ANSI A10.28, Work Platforms Suspended From Cranes or Derricks. ANSI A10.18, Floor and Wall Openings, Railings and Toe Boards. ASME B30.1, Jacks ASME B30.2, Overhead and Gantry Cranes (Top-Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist). ASME B30.5, Mobile and Locomotive Cranes. ASME B30.6, Derricks. ASME B30.7, Base-Mounted Drum Hoists. ASME B30.9, Slings.

245

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 PREENGINEERED PRODUCTION LIFTS 3-i Chapter 3 Preengineered Production Lifts This chapter provides requirements for the design, evaluation, and performance of preengineered production lifts. This lift designation may be used at the discretion of the contractor for selected operations. 3.1 PREENGINEERED PRODUCTION LIFT DETERMINATION.......................................3-1 3.2 LIFTING FIXTURES..............................................................................................................3-2 3.2.1 Design ..........................................................................................................................3-2 3.2.2 Fabrication ...................................................................................................................3-2

246

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 CRITICAL LIFTS 2-i Chapter 2 Critical Lifts This chapter provides guidelines for critical-lift determination and requirements for planning and performing a critical lift safely and judiciously. 2.1 CRITICAL-LIFT DETERMINATION ................................................................ 2-1 2.2 CRITICAL-LIFT REQUIREMENTS ............................................................. 2-2 DOE-STD-1090-2007 Chapter 2 2-ii Critical Lifts INTENTIONALLY BLANK DOE-STD-1090-2007 2.1 CRITICAL-LIFT DETERMINATION 2-1 Chapter 2 Critical Lifts a. An appointed person shall classify each lift into one of the DOE categories (ordinary, critical, or preengineered production) prior to planning the lift. b. A lift shall be designated critical if any of

247

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 CRITICAL LIFTS 2-i Chapter 2 Critical Lifts This chapter provides guidelines for critical-lift determination and requirements for planning and performing a critical lift safely and judiciously. 2.1 CRITICAL-LIFT DETERMINATION ................................................................ 2-1 2.2 CRITICAL-LIFT REQUIREMENTS ............................................................. 2-2 DOE-STD-1090-2004 Chapter 2 2-ii Critical Lifts INTENTIONALLY BLANK DOE-STD-1090-2004 2.1 CRITICAL-LIFT DETERMINATION 2-1 Chapter 2 Critical Lifts a. An appointed person shall classify each lift into one of the DOE categories (ordinary, critical, or preengineered production) prior to planning the lift. b. A lift shall be designated critical if any of

248

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 LIFTING PERSONNEL 4-i Chapter 4 Lifting Personnel This chapter describes requirements for lifting personnel. 4.1 GENERAL................................................................................................................................4-1 4.1.1 Personnel Lifting Evaluation .......................................................................................4-1 4.1.2 Designated Leader .......................................................................................................4-1 4.1.3 Trial Lift.......................................................................................................................4-2 4.1.4 Lifting Operations........................................................................................................4-2

249

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CHAPTER 17 CHAPTER 17 REFERENCES 17-1 Chapter 17 References American Institute of Steel Construction AISC Specifications for the design, fabrication, and erection of structural steel for buildings. American Iron and Steel Institute AISI Standards for Type-302 or Type-304 stainless steel. American National Standards Institute and American Society of Mechanical Engineers ANSI A10.28, Work Platforms Suspended From Cranes or Derricks. ANSI A10.18, Floor and Wall Openings, Railings and Toe Boards. ASME B30.2, Overhead and Gantry Cranes (Top-Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist). ASME B30.5, Mobile and Locomotive Cranes. ASME B30.6, Derricks. ASME B30.7, Base-Mounted Drum Hoists. ASME B30.9, Slings. ASME B30.10, Hooks.

250

RigMesh: Automatic Rigging for Part-Based Shape Modeling and Deformation Peter Borosan1  

E-Print Network (OSTI)

proficient at commercial, state-of-the-art tools such as Maya and 3ds Max [Autodesk 2012c; Autodesk 2012a

Columbia University

251

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DEFINITIONS........................................1-1 DEFINITIONS........................................1-1 CHAPTER 2 CRITICAL LIFTS .......................................................................2-1 2.1 CRITICAL-LIFT DETERMINATION........................................................ 2-1 2.2 CRITIAL-LIFT REQUIREMENTS............................................................. 2-2 CHAPTER 3 PREENGINEERED PRODUCTION LIFTS................................3-1 3.1 PRENGINEERED PRODUCTION LIFT DETERMINATION................ 3-1 3.2 LIFTING FIXTURES .................................................................................... 3-2 3.3.1 Design ................................................................................................... 3-2 3.3.2 Fabrication ............................................................................................

252

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9 9 MOBILE CRANES 9-i Chapter 9 Mobile Cranes This chapter specifies operation, inspection, maintenance, and testing requirements for the use of mobile cranes and implements the requirements of ASME B30.5 ("Mobile and Locomotive Cranes"). Only equipment built to appropriate design standards shall be used at DOE installations. 9.1 GENERAL .................................................................................................................................9-1 9.1.1 Operator Training/Qualification ..................................................................................9-1 9.1.2 Load Limits..................................................................................................................9-1 9.1.3 Load Rating Chart........................................................................................................9-1

253

Application of Membranes to Treatment of Water Based Exploration and Production Wastes  

E-Print Network (OSTI)

Page 1. 1 Schematic of a rotary drilling rig??????????????????????????????. 4 1. 2 Subsurface reach and rig sizes in the last thirty years?????????????????? 5 1. 3 Waste disposal statistics??????????????????????????????????.. 12 1... equipment and rotary system equipment. A drilling rig is a machine used to drill the wellbore [2], it usually entails every equipment in the drilling process apart from the living quarters. Onshore drilling rig types includes the conventional rig...

Olatubi, Oluwaseun Alfred

2010-10-12T23:59:59.000Z

254

Multipurpose active/passive motion compensation system  

SciTech Connect

A microprocessor-controlled active/passive motion compensation system has been developed for deploying a variety of geotechnical in-situ testing devices with mobile drilling rigs from low-cost service vessels. The light-weight rotary heave compensator incorporates a hydraulic motor as the compensator actuator and a servo-controlled closed loop pump to reduce the air storage and power requirements. Unique features of the system are the use of inertial sensors to measure three components of boat motion, the ability to run the system in active/passive or passive modes, and the ability to automatically lower the drillstring at a constant velocity while maintaining motion compensation. Quantitative measurements made during sea trials offshore California yielded motion compensation accuracy approaching 98 percent which is much better than the compensation achieved with passive systems. Results are presented from offshore in-situ testing with a cone penetrometer, a vane shear device, and a suspension PS logger. The system can also be used for other offshore applications.

Sullivan, R.A.; Clements, R.E.; Davenport, M.R.

1984-05-01T23:59:59.000Z

255

BioScope: An Extensible Bandage System for Facilitating Data Collection in Nursing Assessments  

E-Print Network (OSTI)

assessment. ACM Classification Keywords H.4.m Information Systems Applications: Miscellaneous INTRODUCTIONScope's design and leverage it to assist with data collection in numerous potential applications. H.5.m. Information interfaces and presentation (e.g., HCI): critical role in gathering patient-related information

Ouhyoung, Ming

256

Interdependence of the Electricity Generation System and the Natural Gas System and Implications for Energy Security  

E-Print Network (OSTI)

Approved for public release; distribution is unlimited. Lexington Massachusetts This page intentionally left blank. EXECUTIVE SUMMARY Concern about energy security on domestic Department of Defense installations has led to the possibility of using natural gas-fired electricity generators to provide power in the event of electric grid failures. As natural gas is an increasingly base-load fuel for electricity generation in the United States, the electricity generation system has become increasingly dependent on the operation of the natural gas system. However, as the natural gas system is also partly dependent on electricity for its ability to deliver natural gas from the well-head to the consumer, the question arises of whether, in the event of an electric grid failure, the natural gas would continue to flow. As the natural gas transmission system largely uses natural gas from the pipelines as a source of power, once the gas has been extracted from the ground, the system is less dependent on the electric grid. However, some of the drilling rigs, processing units, and pipeline compressors do depend on electric power, making the vulnerability to the system to a disruption in the national electricity supply network vary depending on the cause, breadth, and geographic location of the disruption. This is due to the large numbers of players in the natural gas production and

N. Judson; N. Judson

2013-01-01T23:59:59.000Z

257

WIMS - Waste Information Management System  

Office of Environmental Management (EM)

Welcome To WIMS Welcome To WIMS Waste Information Management System WIMS new web address: http://www.emwims.org WIMS is developed to provide DOE Headquarters and site waste managers with the tools necessary to easily visualize, understand, and manage the vast volumes, categories, and problems of forecasted waste streams. WIMS meets this need by providing a user-friendly online system to gather, organize, and present waste forecast data from DOE sites. This system provides a method for identification of waste forecast volumes, material classes, disposition pathways, and potential choke points and barriers to final disposition. Disclaimer: Disposition facility information presented is for planning purposes only and does not represent DOE's decisions or commitments. Any selection of disposition facility will be made after technical, economic, and policy considerations.

258

New mud system produces solids-free, reusable water  

SciTech Connect

The Corpus Christi, Texas, based Cameron Equipment Co., Inc., has developed a closed-loop mud treating system that removes solids from water-based systems and leaves the separated fluid clean and chemical free enough to be re-used directly on the rig. The system has been successfully applied by a Gulf of Mexico operator in areas where zero discharge is required. The alternative mud conditions program offered by the developers is called the Cameron Fluid Recycling System. Designed for closed-loop water-based fluids, the system is a new method of removing solids from normally discharged fluids such as drilling mud, waste and wash water, or any other water-based fluid that contains undesirable solids. The patented method efficiently produces end products that are (1) dry solids; and (2) essentially 100% solids-free fluid that can be re-used in the same mud system. All excess drilling mud, and all wash water that would normally go to the reserve pit or a cuttings barge are collected in a tank. Recycled fluid is compatible with the mud system fluid, no harmful chemicals are used, and pH is not altered.

NONE

1996-02-01T23:59:59.000Z

259

Recommended Practice for Patch Management of Control Systems  

SciTech Connect

A key component in protecting a nation’s critical infrastructure and key resources is the security of control systems. The term industrial control system refers to supervisory control and data acquisition, process control, distributed control, and any other systems that control, monitor, and manage the nation’s critical infrastructure. Critical Infrastructure and Key Resources (CIKR) consists of electric power generators, transmission systems, transportation systems, dam and water systems, communication systems, chemical and petroleum systems, and other critical systems that cannot tolerate sudden interruptions in service. Simply stated, a control system gathers information and then performs a function based on its established parameters and the information it receives. The patch management of industrial control systems software used in CIKR is inconsistent at best and nonexistent at worst. Patches are important to resolve security vulnerabilities and functional issues. This report recommends patch management practices for consideration and deployment by industrial control systems owners.

Steven Tom; Dale Christiansen; Dan Berrett

2008-12-01T23:59:59.000Z

260

Drilling operations change gear  

SciTech Connect

Predicts that several technological developments (e.g. measurement-while-drilling tools, computer data-gathering systems, improved drill bits, muds, downhole mud motors, and more efficient rigs) will have a major effect on drilling operations in the not-too-distant future. While several companies manufacture MWD systems and most can boast of successful runs, the major problem with the MWD system is cost. Manufacturers continue to make advances in both turbine and positive displacement mud motors. As the life span of downhole mud motors improves, these motors can economically compete with a rotary rig in drilling certain straight-hole intervals. Prototype bit designs include the use of lasers, electronic beams, flames, sparks, explosives, rocket exhaust, chains, projectiles, abrasive jets, and high-pressure erosion. Because drilling fluids are taking a large share of the drilling budget, mud engineers are trying to optimize costs, while maintaining well bore stability and increasing penetration rates. Many companies are taking the strategy of designing the simplest mud program possible and increasing additives only as needed. Air and foam drilling techniques are gaining attention. Concludes that as crude oil prices increase and the rig count begins to rebound, attention will once again turn to drilling technology and methodology.

Moore, S.D.

1982-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Implementation of the Regulatory Authority Information System in Egypt  

Science Journals Connector (OSTI)

As part of the implementation of a barcode-based system to track Radioactive Sealed Sources (RSS) in Egypt, the Regulatory Authority Information System Personal Digital Assistant (RAIS PDA) application was developed to extend the functionality of the International Atomic Energy Agency's (IAEA's) RAIS database by allowing users to download RSS data from the database to a portable PDA equipped with a barcode scanner. The system allows users to verify RSS data, gather RSS audit information and upload that data to the RAIS database in the field. This paper describes the development of the RAIS PDA application, its features and how it will be implemented in Egypt.

S.D. Carson; R. Schetnan; A. Hasan; Y.T. Mohamed

2008-01-01T23:59:59.000Z

262

Scholars from northeast Brazil, Costa Rica, southeast Mexico, Nicaragua, Italy, and the United States gathered for a think-tank international week April 18-22, 2011 to examine Latin America's equity-gap challenges using a community engagement  

E-Print Network (OSTI)

Scholars from northeast Brazil, Costa Rica, southeast Mexico, Nicaragua, Italy, and the United. The keynote address--Brazil's Unified Health System May Promote Social Inequality: Paradox or dialectic/northeastern Brazil constitute nadirs of economic and health inequality. The stunting rates among children

Liu, Taosheng

263

HPCT MPI Profiling and Tracing Library on BG/P Systems | Argonne Leadership  

NLE Websites -- All DOE Office Websites (Extended Search)

MPI Profiling and Tracing Library on BG/P Systems MPI Profiling and Tracing Library on BG/P Systems References IBM System Blue Gene Solution: High Performance Computing Toolkit for Blue Gene/P - IBM Redbook describing HPCT and other performance tools Introduction The HPC Toolkit provides a mechanism for obtain information about the use of MPI routines during a programs execution. This is done through the use of a library which intercepts calls to MPI routines, records information about the call, and then continues with the MPI call. When the program terminates use of MPI by calling MPI_Finalize the data gathered by the library is written to one or more files in the program execution directory. The the primary types of information that are gathered and writen by the library are: MPI Profile Data- A summary of MPI usage information typically

264

EIA-176 Electronic Filing System (EFS)  

Gasoline and Diesel Fuel Update (EIA)

EIA-176 Electronic Filing System (EFS) EIA-176 Electronic Filing System (EFS) Released: January 17, 2013 Background The Form EIA-176, "Annual Report of Natural and Supplemental Gas Supply and Disposition," is used to collect data on the supply and disposition of natural gas in the United States. These data are collected by the Energy Information Administration (EIA), U.S. Department of Energy (DOE), to fulfill its responsibilities for gathering and reporting energy data. Reporting on the Form EIA-176 is mandatory. Electronic Filing System The Form EIA-176 Electronic Filing System (EFS) provides respondents with an efficient and effective means for filing the form using a personal computer (PC). Respondents have a choice of submitting data via either secure file transfer or email. Hardware / Software Requirements

265

Jadoo Power Systems Inc | Open Energy Information  

Open Energy Info (EERE)

Jadoo Power Systems Inc Jadoo Power Systems Inc Jump to: navigation, search Name Jadoo Power Systems Inc Place Folsom, California Zip 95630 Product US-based fuel cell developer, Jadoo Power Systems Inc, produces high energy density power products for the law enforcement, military and electronic news gathering applications. Coordinates 39.474081°, -80.529699° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.474081,"lon":-80.529699,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

266

Optical fiber inspection system  

DOE Patents (OSTI)

A remote optical inspection system including an inspection head. The inspection head has a passageway through which pellets or other objects are passed. A window is provided along the passageway through which light is beamed against the objects being inspected. A plurality of lens assemblies are arranged about the window so that reflected light can be gathered and transferred to a plurality of coherent optical fiber light guides. The light guides transfer the light images to a television or other image transducer which converts the optical images into a representative electronic signal. The electronic signal can then be displayed on a signal viewer such as a television monitor for inspection by a person. A staging means can be used to support the objects for viewing through the window. Routing means can be used to direct inspected objects into appropriate exit passages for accepted or rejected objects. The inspected objects are advantageously fed in a singular manner to the staging means and routing means. The inspection system is advantageously used in an enclosure when toxic or hazardous materials are being inspected. 10 figs.

Moore, F.W.

1985-04-05T23:59:59.000Z

267

Advanced turbine systems program conceptual design and product development: Quarterly report, November 1993--January 1994  

SciTech Connect

This report describes progress made in the advanced turbine systems program conceptual design and product development. The topics of the report include selection of the Allison GFATS, castcool technology development for industrial engines test plan and schedule, code development and background gathering phase for the ultra low NOx combustion technology task, active turbine clearance task, and water vapor/air mixture cooling of turbine vanes task.

NONE

1995-01-01T23:59:59.000Z

268

Hybrid Geothermal Heat Pump System Research Geothermal Project | Open  

Open Energy Info (EERE)

Hybrid Geothermal Heat Pump System Research Geothermal Project Hybrid Geothermal Heat Pump System Research Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title Hybrid Geothermal Heat Pump System Research Project Type / Topic 1 Recovery Act - Geothermal Technologies Program: Ground Source Heat Pumps Project Type / Topic 2 Topic Area 2: Data Gathering and Analysis Project Description Geothermal, or ground-source heat pump systems have been shown to have superior energy performance to conventional heating and cooling systems in many building types and climates. There has been significant growth in the application of these systems; yet, geothermal systems have only been able to capture a few percent of the heating and cooling market. This is due primarily to the prohibitively high cost of installing the necessary ground loop.

269

A Muscular Rig for Smooth Skinning in Autodesk Maya.  

E-Print Network (OSTI)

?? The limitations of the default skinning methods in Autodesk Maya can be compensated for when seeking realistic skin deformations of a human being. The… (more)

Björkman, Pontus

2007-01-01T23:59:59.000Z

270

CRAD, Hoisting & Rigging Assessment Plan | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

on a scheduled basis, certifying that safe operations are in compliance with good conduct of operations. DOE-STD-1090-2001 Equipment operators comply with "industry best...

271

Cyber Security Procurement Language for Control Systems Version 1.8 |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Cyber Security Procurement Language for Control Systems Version 1.8 Cyber Security Procurement Language for Control Systems Version 1.8 Cyber Security Procurement Language for Control Systems Version 1.8 Supervisory Control and Data Acquisition (SCADA), Process Control System (PCS), Distributed Control System (DCS), etc. generally refer to the systems which control, monitor, and manage the nation's critical infrastructures such as electric power generators, subway systems, dams, telecommunication systems, natural gas pipelines, and many others. Simply stated, a control system gathers information and then performs a function based on established parameters or information it received. Cyber Security Procurement Language for Control Systems Version 1.8 More Documents & Publications AMI System Security Requirements - v1_01-1

272

Achieve Continuous Injection of Solid Fuels into Advanced Combustion System Pressures  

SciTech Connect

The overall objective of this project is the development of a mechanical rotary-disk feeder, known as the Stamet Posimetric High Pressure Solids Feeder System, to feed dry granular coal continuously and controllably into pressurized environments of up to 35 kg/cm{sup 2} (500 psi). This was to be accomplished in two phases. The first task was to review materials handling experience in pressurized operations as it related to the target pressures for this project, and review existing coal preparation processes and specifications currently used in advanced combustion systems. Samples of existing fuel materials were obtained and tested to evaluate flow, sealing and friction properties. This provided input data for use in the design of the Stamet Feeders for the project, and ensured that the material specification used met the requirements of advanced combustion & gasification systems. Ultimately, Powder River Basin coal provided by the PSDF facility in Wilsonville, AL was used as the basis for the feeder design and test program. Based on the material property information, a Phase 1 feeder system was designed and built to accomplish feeding the coal to an intermediate pressure up to 21 kg/cm{sup 2} (300 psi) at feed rates of approximately 100 kilograms (220lbs) per hour. The pump & motor system was installed in a custom built test rig comprising an inlet vessel containing an active live-wall hopper mounted in a support frame, transition into the pump inlet, transition from pump outlet and a receiver vessel containing a receiver drum supported on weigh cells. All pressure containment on the rig was rated for the final pressure requirement of 35 kg/cm{sup 2} (500psi). A program of testing and modification was carried out in Stamet's facility in CA, culminating in successful feeding of coal into the Phase 1 target of 21 kg/cm{sup 2} (300psi) gas pressure in December 2003. Further testing was carried out at CQ Inc's facility in PA, providing longer run times and experience of handling and feeding the coal in winter conditions. Based on the data developed through the testing of the Phase I unit, a Phase II system was designed for feeding coal into pressures of up to 35 kg/cm{sup 2} (500 psi). A further program of testing and modification was then carried out in Stamet's facility, with the target pressure being achieved in January 2005. Repeated runs at pressure were achieved, and optimization of the machine resulted in power reductions of 60% from the first successful pressure runs. General design layout of a commercial-scale unit was conducted, and preliminary cost estimates for a commercial unit obtained.

Derek L. Aldred; Timothy Saunders

2005-07-01T23:59:59.000Z

273

Geothermal Progress Monitor: system status and operational experience  

SciTech Connect

The Geothermal Progress Monitor (GPM) is an information system designed and implemented by the MITRE Corporation on behalf of the Division of Geothermal and Hydropower Technology (DGHT, formerly Division of Geothermal Energy) of the US Department of Energy (DOE). Its purpose is to keep track of and to report significant events and trends in the US geothermal industry and the federal geothermal program. The information sources of the GPM system are paper and computerized files maintained by a number of organizations throughout the United States. Trade and technical publications are also used to supplement the information-gathering network. Periodic reports from the GPM system consist mainly of manual and computerized analyses of the collected data. In addition, significant events and activities are usually highlighted. The GPM serves a dual function for DGHT and other members of the Interagency Geothermal Coordinating Council (IGCC). It supports effective management of the federal geothermal program and it provides information for executive, legislative, statutory, and public needs. This paper is a report on the current status of the GPM system and a summary of MITRE's operational experience during calendar year 1981 and the first quarter of 1982. It includes a description of the required output and the mechanism by which the information is gathered, integrated, and published as a Geothermal Progress Monitor Report.

Gerstein, R.E.; Kenkeremath, L.D.; Murphy, M.B.; Entingh, D.J.

1982-03-01T23:59:59.000Z

274

Voice pitch predicts reproductive success in male hunter-gatherers  

Science Journals Connector (OSTI)

...for all analyses (for review of multivariate techniques...Licht (1995)). A standard test of normality for...the null, hence we use standard ordinary least squares...influence female choice (for review, see Andersson (1994)). For future work, we plan to examine experimentally...

2007-01-01T23:59:59.000Z

275

Fault Tolerance in Data Gathering Wireless Sensor Networks  

Science Journals Connector (OSTI)

......total 30% node faults. FIGURE 8. Energy efficiency. better than LEACH when link error...Efficiency In this section, we analyze the energy efficiency (in Fig. 8) and time efficiency...May 1213, pp. 474479. The Printing House, Inc. [14] Huang, S. K., Ssu......

Guangyan Huang; Yanchun Zhang; Jing He; Jinli Cao

2011-06-01T23:59:59.000Z

276

Engineer 2020 and the Gathering Storm Alice M. Agogino  

E-Print Network (OSTI)

that the world will not effectively address issues such as the climate-energy challenge without America ­ its and Employing America For a Brighter Economic Future · "Wake-up Call" Statistics · Powerful Recommendations #12 Explosion in Healthcare #12;6 Flat World Socio-Technological Challenges · Physical infrastructures in urban

Agogino, Alice M.

277

Microsoft Word - DOE News Release - 'DOE, Contractors Gather...  

NLE Websites -- All DOE Office Websites (Extended Search)

Ky. - The U.S. Department of Energy (DOE) and its Paducah contractors are collecting food and personal hygiene items to help restock the shelves of Paducah area service...

278

Efficient Gathering of Correlated Data in Sensor Networks  

E-Print Network (OSTI)

[Wattenhofer et al. 2001]. In this article, we focus on designing techniques to conserve energy by exploiting to some of the other mentioned approaches, and can be used in combination with them to conserve energy that exploit data correlations in sensor data to minimize communication costs (and hence, energy costs

Gupta, Himanshu

279

A Majestic And Raucous Gathering of Sandhill Cranes Jeff Mitton  

E-Print Network (OSTI)

straight out and long primary feathers at the wingtips deftly working the wind. Large cranes can be seen in the Bosque del Apache National Wildlife Refuge, 100 miles south of Albuquerque rest for several weeks old and some cranes live for 25 years. The wildlife areas along the Platte River insulate

Mitton, Jeffry B.

280

Fault Tolerance in Data Gathering Wireless Sensor Networks  

Science Journals Connector (OSTI)

......to our analysis of LEACH code [26] implemented in the network simulator 2 (ns2) [28]) and do not wait...generated by the tool in LEACH code in ns2 [28] in a square area...default setting in LEACH code in [28]: NCH = 5, the......

Guangyan Huang; Yanchun Zhang; Jing He; Jinli Cao

2011-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Dwarf Fortress gathers at the statue and attends a party  

E-Print Network (OSTI)

In designing DwarfFortress as part roguelike and part simulation, Tarn and Zach Adams of Bay 12 Games drew on a tradition of game genres that used proceduralism and simulation to give players unique paths through the game. ...

Diaz, Joshua Lindsay

2009-01-01T23:59:59.000Z

282

Gathering the landscape : a community arts center on Lookout Mountain  

E-Print Network (OSTI)

With a tape measure and a pad of newsprint, to document, understand and re-present a natural place was the first goal of this thesis. From this understanding a new built presence, a redefinition of the site, is sought, to ...

Govan, Christine Noble, 1958-

1989-01-01T23:59:59.000Z

283

The complex structure of hunter–gatherer social networks  

Science Journals Connector (OSTI)

...effects of competition for energy, materials and information...societies all resources, including energy, materials and information...BentleyThe power law of rank and household on the North Pacific. In Complex...of Tokyo Press 1980Tokyo, Japan:University of Tokyo Press...

2007-01-01T23:59:59.000Z

284

Fluidized-Bed Waste-Heat Recovery System Advances  

E-Print Network (OSTI)

ACCESS DOOR (TYPICAL) 1.. LEVEL . PUTFORII ?n'if~~??? FLUIDIZED L--lJ FLUE ';:S ! "'D I DUCT , PRQVISK>N FOR 14" I.P.S. : FLUE GAS . LFr UN! J-~DU~C~T~CL!:!:E~ANO~UT~? RE~':aL:"-~L_--WL:!:!J~~~=:IAIR 1." I.P.S. PREHEATED COMBUSTION AIR... of six months. Data gathered will be used to evaluate performance, energy savings. and economic attractiveness of the FBWHR system. ACKNOWLEDGEMENT This work was jointly funded by the Depart ment of Energy and Thermo Electron Corporation...

Patch, K. D.; Cole, W. E.

285

Identification of rotordynamic forces in a flexible rotor system using magnetic bearings  

E-Print Network (OSTI)

Methods are presented for parameter identification of an annular gas seal on a flexiblerotor test rig. Dynamic loads are applied by magnetic bearings (MBs) that support the rotor. MB forces are measured using fiber-optic strain gauges...

Zutavern, Zachary Scott

2009-06-02T23:59:59.000Z

286

Microsoft Word - AMI System Security Requirements - v1_01-1.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

UCAIUG: AMI-SEC-ASAP UCAIUG: AMI-SEC-ASAP AMI System Security Requirements V1.01 ASAP 12/17/2008 AMI System Security Specification v1.0 Page i Executive Summary 1 This document provides the utility industry and vendors with a set of security requirements for 2 Advanced Metering Infrastructure (AMI). These requirements are intended to be used in the 3 procurement process, and represent a superset of requirements gathered from current cross- 4 industry accepted security standards and best practice guidance documents. 5 6 This document provides substantial supporting information for the use of these requirements 7 including scope, context, constraints, objectives, user characteristics, assumptions, and 8

287

Parameter monitoring compensation system and method  

DOE Patents (OSTI)

A compensation system is described for a computer-controlled machining apparatus having a controller and including a cutting tool and a workpiece holder which are movable relative to one another along a preprogrammed path during a machining operation. It utilizes sensors for gathering information at a preselected stage of a machining operation relating to an actual condition. The controller compares the actual condition to a condition which the program presumes to exist at the preselected stage and alters the program in accordance with detected variations between the actual condition and the assumed condition. Such conditions may be related to process parameters, such as a position, dimension or shape of the cutting tool or workpiece or an environmental temperature associated with the machining operation, and such sensors may be a contact or a non-contact type of sensor or a temperature transducer. 7 figs.

Barkman, W.E.; Babelay, E.F.; DeMint, P.D.; Hebble, T.L.; Igou, R.E.; Williams, R.R.; Klages, E.J.; Rasnick, W.H.

1995-02-07T23:59:59.000Z

288

Tss4U BV formerly Holecsol R S Renewable Energy Systems and Shell Solar  

Open Energy Info (EERE)

Tss4U BV formerly Holecsol R S Renewable Energy Systems and Shell Solar Tss4U BV formerly Holecsol R S Renewable Energy Systems and Shell Solar Energy Jump to: navigation, search Name Tss4U BV (formerly Holecsol, R&S Renewable Energy Systems and Shell Solar Energy) Place Veldhoven, Netherlands Zip 5503 Sector Solar, Wind energy Product Provides small solar and wind for offgrid applications, notably power for oil rigs. Coordinates 51.421746°, 5.404554° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":51.421746,"lon":5.404554,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

289

An Acquisition and Distribution System for Situational Awareness William E. Green, Paul Y. Oh, and Seunghyun Yoon  

E-Print Network (OSTI)

take over 10 minutes just to lift 20 lbs. Rotary wing aircraft, like helicopters [6] [4] [2], rely images. LEAP consists of a kite fur- nished with a teleoperated camera rig and stabiliza- tion mechanism

Oh, Paul

290

Physical protection system design and evaluation  

SciTech Connect

The design of an effective physical protection system includes the determination of physical protection system objectives, initial design of a physical protection system, design evaluation, and probably a redesign or refinement. To develop the objectives, the designer must begin by gathering information about facility operation and conditions, such as a comprehensive description of the facility, operating conditions, and the physical protection requirements. The designer then needs to define the threat. This involves considering factors about potential adversaries: class of adversary, adversary`s capabilities, and range of adversary`s tactics. Next, the designer should identify targets. Determination of whether or not the materials being protected are attractive targets is based mainly on the ease or difficulty of acquisition and desirability of the material. The designer now knows the objectives of the physical protection system, that is, {open_quotes}what to protect against whom.{close_quotes} The next step is to design the system by determining how best to combine such elements as fences, vaults, sensors and assessment devices, entry control elements, procedures, communication devices, and protective forces personnel to meet the objectives of the system. Once a physical protection system is designed, it must be analyzed and evaluated to ensure it meets the physical protection objectives. Evaluation must allow for features working together to ensure protection rather than regarding each feature separately. Due to the complexity of the protection systems, an evaluation usually requires modeling techniques. If any vulnerabilities are found, the initial system must be redesigned to correct the vulnerabilities and a reevaluation conducted. This paper reviews the physical protection system design and methodology mentioned above. Examples of the steps required and a brief introduction to some of the technologies used in modem physical protections system are given.

Williams, J.D.

1997-03-01T23:59:59.000Z

291

Computer program design for land treatment systems  

SciTech Connect

Municipal Sludge Land Application expert System (MuSLAXS)is as expert system developed for site assessment and design analysis of municipal sludge application on agricultural land. The system has knowledge on the technical and regulatory aspects of sludge land application and understanding of soil-plant systems for South Carolina. It can be effectively used outside South Carolina with modifications to incorporate specific regulations on land treatment and soil and crop database. A database supports this expert system and provides appropriate default values for sludge and soil characteristics, and fertilizer recommendations for crops commonly grown in South Carolina. Information on the sludge characteristics is gathered from the user, if it is available, or it is retrieved from the sludge database. Based on the recommendations by the EPA and the expert, a list of 22 constituents, for which the sludge should be analyzed is developed. This list includes: total solids, volatile solids, total nitrogen (TNK), ammonia-nitrogen, organic-nitrogen, phosphorus, potassium, sulfur, cadmium, copper, lead, nickel, zinc, PCBs, calcium, magnesium, chromium, boron, arsenic, aluminum, cobalt, and molybdenum.

White, R.K. (Clemson Univ. SC (USA)); Jantrania, A.

1989-10-01T23:59:59.000Z

292

RMOTC - Library - Fact Sheets  

NLE Websites -- All DOE Office Websites (Extended Search)

Inventory On-site equipment includes forklifts, backhoes, and workover rigs. Geothermal Enhanced Geothermal System (EGS) and low-temperature testing. Flow Assurance Test...

293

The TMI defueling project fuel debris removal system  

SciTech Connect

The Three Mile Island (TMI) unit 2 pressurized water reactor loss-of-coolant accident on March 28, 1979, presented the nuclear community with many challenging remediation problems. A plethora of techniques, systems, and tools have been employed for the recovery and packaging of the postaccident configuration of the reactor core. Of particular difficulty was the removal of the fuel debris located beneath the lower core support structure. Fuel debris located beneath the lower core support structure was the result of rapid cooling of the previously molten UO{sub 2} and ZrO{sub 2}, causing formation of a ceramic like rubble. Approximately 19,100 kg of this rubble settled beneath the lower core support structure and onto the lower head of the reactor containment vessel. The development and implementation of a debris collection system based on the air lift principle proved to be an effective method for gathering the fuel debris from beneath the lower core support structure.

Burge, B. (EG and G Idaho, Inc., Idaho Falls (United States))

1992-01-01T23:59:59.000Z

294

CRAD, Management - Office of River Protection K Basin Sludge Waste System |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Office of River Protection K Basin Sludge Waste Office of River Protection K Basin Sludge Waste System CRAD, Management - Office of River Protection K Basin Sludge Waste System May 2004 A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a May 2004 assessment of the Management at the Office of River Protection K Basin Sludge Waste System. CRADs provide a recommended approach and the types of information to gather to assess elements of a DOE contractor's programs. CRAD, Management - Office of River Protection K Basin Sludge Waste System More Documents & Publications CRAD, Emergency Management - Office of River Protection K Basin Sludge Waste System CRAD, Conduct of Operations - Office of River Protection K Basin Sludge

295

EIA - Natural Gas Pipeline System - Links to U.S. Natural Gas Pipeline  

U.S. Energy Information Administration (EIA) Indexed Site

Links Links About U.S. Natural Gas Pipelines - Transporting Natural Gas based on data through 2007/2008 with selected updates Links to U.S. Natural Gas Pipeline Information - The links below will either direct the user to a narrative describing the system, a pipeline system map, a FERC prescribed "Informational Postings" page, or a FERC Tariff Sheet. Pipeline Name Type of System Regions of Operations Acadian Gas Pipeline System Intrastate Southwest Algonquin Gas Transmission Co Interstate Northeast Alliance Pipeline Co Interstate Central, Midwest Anaconda Pipeline System Gathering Gulf of Mexico ANR Pipeline Co Interstate Midwest ANR Storage Co Interstate Midwest Arkansas Oklahoma Gas Co Intrastate Southwest Arkansas Western Pipeline Co Intrastate

296

Advances and challenges in ORC systems modeling for low grade thermal energy recovery  

Science Journals Connector (OSTI)

Abstract Low-grade thermal energy recovery has attained a renewed relevance, driven by the desire to improve system efficiency and reduce the carbon footprint of power generation. Various technologies have been suggested to exploit low-temperature thermal energy sources, otherwise difficult to access using conventional power generation systems. In this paper, the authors review the most recent advances and challenges for the exploitation of low grade thermal energy resources, with particular emphasis on ORC systems, based on information gathered from the technical literature. An outline of the issues related to ORC system modeling is also presented, and some guidelines drawn to develop an effective and powerful simulation tool. As a summary conclusion of the revised models, a simulation tool of an ORC system suitable for the exploitation of low grade thermal energy is introduced.

Davide Ziviani; Asfaw Beyene; Mauro Venturini

2014-01-01T23:59:59.000Z

297

Using Bayesian Network to Develop Drilling Expert Systems  

E-Print Network (OSTI)

in foam UBD ............................................ 82 67 Overall air and gas UBD ........................................................................... 83 68 Rotary and hammer drilling options... .......................................................... 84 69 A list of limits and challenges for air and gas UBD .................................. 85 70 A list of possible gas drilling operations ................................................... 86 71 A list of possible rig equipment...

Alyami, Abdullah

2012-10-19T23:59:59.000Z

298

Library System Library System  

E-Print Network (OSTI)

Library System #12;Library System 5150 Anthony Wayne Drive David Adamany Undergraduate Library that for the current fiscal year, we've been given an additional $600,000 for our library materials budget. We're very subscriptions. The Wayne State University Libraries are deeply committed to providing our faculty and students

Cinabro, David

299

Remote controlled underground mining system preliminary design and concept plans. Final report  

SciTech Connect

The proposed mining technique has the potential to mine coal from underground horizontal or pitching seams in the 9-foot thickness range at an estimated cost ranging from $7.987 to $10.152 per ton. The estimate is established on conclusions drawn from: (1) the anticipated mining rate, in terms of tons per hour, that the mining system's hardware is expected to achieve as an average; (2) the approximate cost of the mining hardware amortized on a production service life expectancy of 4,000,000 tons; (3) logistics pertinent to continuous mine production, requiring the operation of two Mining Rigs simultaneously with operating crews totaling to 9 men per shift; (4) the angle of the mine bores into pitching seams extend, whenever possible, to no more than 30/sup 0/ from the horizontal; (5) mine bores extend to maximum feasible or permissible length. A bore length of 2500 feet is considered feasible; and (6) gas recovery from the mine bores can be accomplished with relative ease. The value of this, however, has not been determined since its handling as a recoverable requires investigation on hardware assemblies necessary to its processing, and the volume that must exist to invite a commercially attractive effort.

Haspert, J.C.

1984-03-01T23:59:59.000Z

300

A Publication of the Texas Transportation Institute Member of The Texas A&M University System Vol. 38 No. 4 2002 OUR SPONSORS  

E-Print Network (OSTI)

vehicle safety testing and a range of other experiments. The Hydraulics, Sedimentation and Erosion Control to 80,000-pound tractor-trailer rigs. "The total crash testing effort includes expert engineering

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Army Energy and Water Reporting System Assessment  

SciTech Connect

There are many areas of desired improvement for the Army Energy and Water Reporting System. The purpose of system is to serve as a data repository for collecting information from energy managers, which is then compiled into an annual energy report. This document summarizes reported shortcomings of the system and provides several alternative approaches for improving application usability and adding functionality. The U.S. Army has been using Army Energy and Water Reporting System (AEWRS) for many years to collect and compile energy data from installations for facilitating compliance with Federal and Department of Defense energy management program reporting requirements. In this analysis, staff from Pacific Northwest National Laboratory found that substantial opportunities exist to expand AEWRS functions to better assist the Army to effectively manage energy programs. Army leadership must decide if it wants to invest in expanding AEWRS capabilities as a web-based, enterprise-wide tool for improving the Army Energy and Water Management Program or simply maintaining a bottom-up reporting tool. This report looks at both improving system functionality from an operational perspective and increasing user-friendliness, but also as a tool for potential improvements to increase program effectiveness. The authors of this report recommend focusing on making the system easier for energy managers to input accurate data as the top priority for improving AEWRS. The next major focus of improvement would be improved reporting. The AEWRS user interface is dated and not user friendly, and a new system is recommended. While there are relatively minor improvements that could be made to the existing system to make it easier to use, significant improvements will be achieved with a user-friendly interface, new architecture, and a design that permits scalability and reliability. An expanded data set would naturally have need of additional requirements gathering and a focus on integrating with other existing data sources, thus minimizing manually entered data.

Deprez, Peggy C.; Giardinelli, Michael J.; Burke, John S.; Connell, Linda M.

2011-09-01T23:59:59.000Z

302

DOE REAL-TIME SEISMIC MONITORING AT ENHANCED GEOTHERMAL SYSTEM SITES | Open  

Open Energy Info (EERE)

REAL-TIME SEISMIC MONITORING AT ENHANCED GEOTHERMAL SYSTEM SITES REAL-TIME SEISMIC MONITORING AT ENHANCED GEOTHERMAL SYSTEM SITES Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: DOE REAL-TIME SEISMIC MONITORING AT ENHANCED GEOTHERMAL SYSTEM SITES Details Activities (6) Areas (6) Regions (0) Abstract: Lawrence Berkeley National Laboratory (LBNL) at the direction of the United States Department of Energy (DOE) Geothermal Technologies EGS Program is installing, operating, and/or interfacing seismic arrays at multiple Enhanced Geothermal Systems (EGS) sites. The overall goal is to gather high resolution seismicity data before, during and after stimulation activities at the EGS projects. This will include both surface and borehole deployments (as necessary in available boreholes) to provide high quality

303

CRAD, Training - Office of River Protection K Basin Sludge Waste System |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Office of River Protection K Basin Sludge Waste Office of River Protection K Basin Sludge Waste System CRAD, Training - Office of River Protection K Basin Sludge Waste System May 2004 A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a May 2004 assessment of the Environment, Safety and Health program at the Office of River Protection K Basin Sludge Waste System. CRADs provide a recommended approach and the types of information to gather to assess elements of a DOE contractor's programs. CRAD, Training - Office of River Protection K Basin Sludge Waste System More Documents & Publications CRAD, Emergency Management - Office of River Protection K Basin Sludge

304

CRAD, Engineering - Office of River Protection K Basin Sludge Waste System  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Engineering - Office of River Protection K Basin Sludge Waste Engineering - Office of River Protection K Basin Sludge Waste System CRAD, Engineering - Office of River Protection K Basin Sludge Waste System May 2004 A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a May 2004 assessment of the Engineering program at the Office of River Protection K Basin Sludge Waste System. CRADs provide a recommended approach and the types of information to gather to assess elements of a DOE contractor's programs. CRAD, Engineering - Office of River Protection K Basin Sludge Waste System More Documents & Publications CRAD, Emergency Management - Office of River Protection K Basin Sludge

305

Insights into the design, use and implementation of home energy management systems  

Science Journals Connector (OSTI)

Between 2008 and 2011, three different home energy management systems (HEMS) that give feedback on energy consumption were implemented in households in the Netherlands. Home energy management systems are defined as intermediary devices that can visualise, monitor and/or manage domestic gas and/or electricity consumption. Through a series of questionnaires, interviews, focus groups and usability tests, a wide range of knowledge was gathered on factors influencing the effectiveness of the three systems. The resulting insights were structured with the help of a conceptual model, which outlines the various interactions between users, energy monitors, and their social and physical environments. The insights provide a broad spectrum of factors to be considered for the successful design and implementation of home energy management systems. This paper aims to provoke an open discussion to ascertain the value of the different factors and further the development of effective and useful HEMS.

S.S. Van Dam; C.A. Bakker; J.D.M. Van Hal

2012-01-01T23:59:59.000Z

306

NUCLEAR NON-PROLIFERATION-TASK 1: Deployable Plume and Aerosol Release Prediction and Tracking System  

SciTech Connect

This contract was awarded in response to a proposal in which a deployable plume and aerosol release prediction and tracking system would be designed, fabricated, and tested. The system would gather real time atmospheric data and input it into a real time atmospheric model that could be used for plume predition and tracking. The system would be able to be quickly deployed by aircraft to points of interest or positioned for deployment by vehicles. The system would provide three dimensional (u, v, and w) wind vector data, inversion height measurements, surface wind information, classical weather station data, and solar radiation. The on-board real time computer model would provide the prediction of the behavior of plumes and released aerosols.

John Kleppe, Ph.D., William Norris, Ph.D., Mehdi Etezada, Ph.D., P.E.

2006-07-19T23:59:59.000Z

307

Feasibility study: utilization of landfill gas for a vehicle fuel system, Rossman's landfill, Clackamas County, Oregon  

SciTech Connect

In 1978, a landfill operator in Oregon became interested in the technical and economic feasibility of recovering the methane generated in the landfill for the refueling of vehicles. DOE awarded a grant for a site-specific feasibility study of this concept. This study investigated the expected methane yield and the development of a conceptual gas-gathering system; gas processing, compressing, and storage systems; and methane-fueled vehicle systems. Cost estimates were made for each area of study. The results of the study are presented. Reasoning that gasoline prices will continue to rise and that approximately 18,000 vehicles in the US have been converted to operate on methane, a project is proposed to use this landfill as a demonstration site to produce and process methane and to fuel a fleet (50 to 400) vehicles with the gas produced in order to obtain performance and economic data on the systems used from gas collection through vehicle operation. (LCL)

None

1981-01-01T23:59:59.000Z

308

Metering Systems  

Energy.gov (U.S. Department of Energy (DOE))

A variety of metering systems are currently on the market for Federal facility implementation. The information below outlines common metering system capabilities and common metering system components.

309

Advanced Seismic While Drilling System  

SciTech Connect

A breakthrough has been discovered for controlling seismic sources to generate selectable low frequencies. Conventional seismic sources, including sparkers, rotary mechanical, hydraulic, air guns, and explosives, by their very nature produce high-frequencies. This is counter to the need for long signal transmission through rock. The patent pending SeismicPULSER{trademark} methodology has been developed for controlling otherwise high-frequency seismic sources to generate selectable low-frequency peak spectra applicable to many seismic applications. Specifically, we have demonstrated the application of a low-frequency sparker source which can be incorporated into a drill bit for Drill Bit Seismic While Drilling (SWD). To create the methodology of a controllable low-frequency sparker seismic source, it was necessary to learn how to maximize sparker efficiencies to couple to, and transmit through, rock with the study of sparker designs and mechanisms for (a) coupling the sparker-generated gas bubble expansion and contraction to the rock, (b) the effects of fluid properties and dynamics, (c) linear and non-linear acoustics, and (d) imparted force directionality. After extensive seismic modeling, the design of high-efficiency sparkers, laboratory high frequency sparker testing, and field tests were performed at the University of Texas Devine seismic test site. The conclusion of the field test was that extremely high power levels would be required to have the range required for deep, 15,000+ ft, high-temperature, high-pressure (HTHP) wells. Thereafter, more modeling and laboratory testing led to the discovery of a method to control a sparker that could generate low frequencies required for deep wells. The low frequency sparker was successfully tested at the Department of Energy Rocky Mountain Oilfield Test Center (DOE RMOTC) field test site in Casper, Wyoming. An 8-in diameter by 26-ft long SeismicPULSER{trademark} drill string tool was designed and manufactured by TII. An APS Turbine Alternator powered the SeismicPULSER{trademark} to produce two Hz frequency peak signals repeated every 20 seconds. Since the ION Geophysical, Inc. (ION) seismic survey surface recording system was designed to detect a minimum downhole signal of three Hz, successful performance was confirmed with a 5.3 Hz recording with the pumps running. The two Hz signal generated by the sparker was modulated with the 3.3 Hz signal produced by the mud pumps to create an intense 5.3 Hz peak frequency signal. The low frequency sparker source is ultimately capable of generating selectable peak frequencies of 1 to 40 Hz with high-frequency spectra content to 10 kHz. The lower frequencies and, perhaps, low-frequency sweeps, are needed to achieve sufficient range and resolution for realtime imaging in deep (15,000 ft+), high-temperature (150 C) wells for (a) geosteering, (b) accurate seismic hole depth, (c) accurate pore pressure determinations ahead of the bit, (d) near wellbore diagnostics with a downhole receiver and wired drill pipe, and (e) reservoir model verification. Furthermore, the pressure of the sparker bubble will disintegrate rock resulting in an increased overall rates of penetration. Other applications for the SeismicPULSER{trademark} technology are to deploy a low-frequency source for greater range on a wireline for Reverse Vertical Seismic Profiling (RVSP) and Cross-Well Tomography. Commercialization of the technology is being undertaken by first contacting stakeholders to define the value proposition for rig site services utilizing SeismicPULSER{trademark} technologies. Stakeholders include national oil companies, independent oil companies, independents, service companies, and commercial investors. Service companies will introduce a new Drill Bit SWD service for deep HTHP wells. Collaboration will be encouraged between stakeholders in the form of joint industry projects to develop prototype tools and initial field trials. No barriers have been identified for developing, utilizing, and exploiting the low-frequency SeismicPULSER{trademark} source in a

Robert Radtke; John Fontenot; David Glowka; Robert Stokes; Jeffery Sutherland; Ron Evans; Jim Musser

2008-06-30T23:59:59.000Z

310

RECIPIENT:Princeton Power Systems STATE: NJ PROJECT Marine High-Voltage Power Conditioning and Transmission System with Integrated Energy Storage  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Princeton Power Systems Princeton Power Systems STATE: NJ PROJECT Marine High-Voltage Power Conditioning and Transmission System with Integrated Energy Storage TITLE: Funding Opportunity Announcement Number Procurement Instrument Number NEPA Control Number cm Number DE-FOA-0000293 DE-EE0003640 GFO-000364~001 GOO Based on my review of the information concerning the proposed action, as NEPA Compliance Officer (authorized under DOE Order 451.1A), I have made the foUowing determination: CX, EA, EIS APPENDIX AND NUMBER: Description: A9 Information gathering (including, but not limited to, ~terature surveys, inventories, audits), data analysis (including computer modeling), document preparation (such as conceptual design or feasibility studies, analytical energy supply

311

Evaluation of industrial combustion control systems. Final report  

SciTech Connect

This study evaluated O/sub 2/ and CO monitoring systems used for combustion controls to provide reliable data on their performance, operating range and accuracy. The study concentrated on three in-situ O/sub 2/ and two in-situ CO monitoring systems which are applicable to furnace and boiler controls. The project provides technical information for cost/benefit analysis of combustion control systems and to help expedite implementation of combustion control technology by industry. The evaluation of the stack gas monitoring systems was carried out for ranges of furnace operating parameters such as fuel to air mixture ratio, burner firing rate, heat extraction rate, fuel type, combustion air preheat temperature, and cyclic operating conditions, which are based on information gathered from typical operational practices of representative industrial furnaces and boilers. The experiments were performed in the NBS experimental furnace under both natural gas and No. 2 fuel oil fired conditions. An on-line gas sampling/analysis system was used as a reference system for comparative evaluation of the stack gas monitors. The system is set up to determine the level of CO, CO/sub 2/, O/sub 2/, NO/NO/sub x/ and total hydrocarbons in the stack gases.

Presser, C.; Semerjian, H.G.

1984-10-01T23:59:59.000Z

312

LASER STABILIZATION FOR NEAR ZERO NO{sub x} GAS TURBINE COMBUSTION SYSTEMS  

SciTech Connect

Historically, the development of new industrial gas turbines has been primarily driven by the intent to achieve higher efficiency, lower operating costs and lower emissions. Higher efficiency and lower cost is obtained through higher turbine operating temperatures, while reduction in emissions is obtained by extending the lean operating limit of the combustor. However reduction in the lean stability limit of operation is limited greatly by the chemistry of the combustion process and by the occurrence of thermo-acoustic instabilities. Solar Turbines, CFD Research Corporation, and Los Alamos National Laboratory have teamed to advance the technology associated with laser-assisted ignition and flame stabilization, to a level where it could be incorporated onto a gas turbine combustor. The system being developed is expected to enhance the lean stability limit of the swirl stabilized combustion process and assist in reducing combustion oscillations. Such a system has the potential to allow operation at the ultra-lean conditions needed to achieve NO{sub x} emissions below 5 ppm without the need of exhaust treatment or catalytic technologies. The research effort was focused on analytically modeling laser-assisted flame stabilization using advanced CFD techniques, and experimentally demonstrating the technology, using a solid-state laser and low-cost durable optics. A pulsed laser beam was used to generate a plasma pool at strategic locations within the combustor flow field such that the energy from the plasma became an ignition source and helped maintain a flame at ultra lean operating conditions. The periodic plasma generation and decay was used to nullify the fluctuations in the heat release from the flame itself, thus decoupling the heat release from the combustor acoustics and effectively reducing the combustion oscillations. The program was built on an existing technology base and includes: extending LANL's existing laser stabilization experience to a sub-scale combustor rig, performing and validating CFD predictions, and ultimately conducting a full system demonstration in a multi-injector combustion system at Solar Turbines.

Vivek Khanna

2002-09-30T23:59:59.000Z

313

Sandia National Laboratories (SNL) and Oak Ridge National Laboratories (ORNL) joint development of SNL`s sample tracking, analysis and reporting (STAR) information system  

SciTech Connect

A comprehensive environmental sample management program allocates much of its resources to collecting, managing, and manipulating information. A computerized system that collects information at the field sampling point, tracks the sample to analytical labs and loads electronic data deliverables from these labs, while maintaining chain of custody and data integrity, is efficient and cost effective for providing consistent and accurate, legally defensible sample data. In June 1993, a team was formed to gather Sample Management Office requirements and begin development of a sample tracking system. This paper is an overview of experiences encountered when Sandia transferred and implemented sample software from the Waste Area Group (WAG6) at ORNL.

Fish, J.; Campbell, D.; Jenkins, B. [and others

1995-05-01T23:59:59.000Z

314

Log Summarization and Anomaly Detection for TroubleshootingDistributed Systems  

SciTech Connect

Today's system monitoring tools are capable of detectingsystem failures such as host failures, OS errors, and network partitionsin near-real time. Unfortunately, the same cannot yet be said of theend-to-end distributed softwarestack. Any given action, for example,reliably transferring a directory of files, can involve a wide range ofcomplex and interrelated actions across multiple pieces of software:checking user certificates and permissions, getting details for allfiles, performing third-party transfers, understanding re-try policydecisions, etc. We present an infrastructure for troubleshooting complexmiddleware, a general purpose technique for configurable logsummarization, and an anomaly detection technique that works in near-realtime on running Grid middleware. We present results gathered using thisinfrastructure from instrumented Grid middleware and applications runningon the Emulab testbed. From these results, we analyze the effectivenessof several algorithms at accurately detecting a variety of performanceanomalies.

Gunter, Dan; Tierney, Brian L.; Brown, Aaron; Swany, Martin; Bresnahan, John; Schopf, Jennifer M.

2007-08-01T23:59:59.000Z

315

HIGH-RESOLUTION INFRARED IMAGING AND SPECTROSCOPY OF THE Z CANIS MAJORIS SYSTEM DURING QUIESCENCE AND OUTBURST  

SciTech Connect

We present adaptive optics photometry and spectra in the JHKL bands along with high spectral resolution K-band spectroscopy for each component of the Z Canis Majoris system. Our high angular resolution photometry of this very young ({approx}<1 Myr) binary, comprised of an FU Ori object and a Herbig Ae/Be star, was gathered shortly after the 2008 outburst while our high-resolution spectroscopy was gathered during a quiescent phase. Our photometry conclusively determines that the outburst was due solely to the embedded Herbig Ae/Be member, supporting results from earlier works, and that the optically visible FU Ori component decreased slightly ({approx}30%) in luminosity during the same period, consistent with previous works on the variability of FU Ori type systems. Further, our high-resolution K-band spectra definitively demonstrate that the 2.294 {mu}m CO absorption feature seen in composite spectra of the system is due solely to the FU Ori component, while a prominent CO emission feature at the same wavelength, long suspected to be associated with the innermost regions of a circumstellar accretion disk, can be assigned to the Herbig Ae/Be member. These findings clarify previous analyses of the origin of the CO emission in this complex system.

Hinkley, Sasha; Hillenbrand, Lynne; Crepp, Justin R. [Department of Astronomy, California Institute of Technology, 1200 E. California Blvd, MC 249-17, Pasadena, CA 91125 (United States); Oppenheimer, Ben R.; Zimmerman, Neil; Brenner, Douglas [Astrophysics Department, American Museum of Natural History, Central Park West at 79th Street, New York, NY 10024 (United States); Rice, Emily L. [Department of Engineering Science and Physics, College of Staten Island, City University of New York, 2800 Victory Bvld, Staten Island, NY 10314 (United States); Pueyo, Laurent [Space Telescope Science Institute, 3700 San Martin Drive, Baltimore, MD 21218 (United States); Vasisht, Gautam; Roberts, Jennifer E.; Roberts, Lewis C. Jr.; Burruss, Rick; Wallace, J. Kent; Cady, Eric; Zhai, Chengxing [Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Dr., Pasadena, CA 91109 (United States); Kraus, Adam L. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA, 02138 (United States); Ireland, Michael J. [Department of Physics and Astronomy, Macquarie University, New South Wales, NSW 2109 (Australia); Beichman, Charles [NASA Exoplanet Science Institute, California Institute of Technology, Pasadena, CA 91125 (United States); Dekany, Richard [Caltech Optical Observatories, California Institute of Technology, Pasadena, CA 91125 (United States); Parry, Ian R. [Institute of Astronomy, University of Cambridge, Madingley Road, Cambridge CB3 0HA (United Kingdom); and others

2013-01-20T23:59:59.000Z

316

Integrated thermal treatment system study: Phase 1 results. Volume 1  

SciTech Connect

An integrated systems engineering approach is used for uniform comparison of widely varying thermal treatment technologies proposed for management of contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. Ten different systems encompassing several incineration design options are studied. All subsystems, including facilities, equipment, and methods needed for integration of each of the ten systems are identified. Typical subsystems needed for complete treatment of MLLW are incoming waste receiving and preparation (characterization, sorting, sizing, and separation), thermal treatment, air pollution control, primary and secondary stabilization, metal decontamination, metal melting, mercury recovery, lead recovery, and special waste and aqueous waste treatment. The evaluation is performed by developing a preconceptual design package and planning life-cycle cost (PLCC) estimates for each system. As part of the preconceptual design process, functional and operational requirements, flow sheets and mass balances, and conceptual equipment layouts are developed for each system. The PLCC components estimated are technology development, production facility construction, pre-operation, operation and maintenance, and decontamination and decommissioning. Preconceptual design data and other technology information gathered during the study are examined and areas requiring further development, testing, and evaluation are identified and recommended. Using a qualitative method, each of the ten systems are ranked.

Feizollahi, F.; Quapp, W.J.; Hempill, H.G.; Groffie, F.J.

1994-07-01T23:59:59.000Z

317

Tuning and Analysis Utilities (TAU) on BG/P Systems | Argonne Leadership  

NLE Websites -- All DOE Office Websites (Extended Search)

and Analysis Utilities (TAU) on BG/P Systems and Analysis Utilities (TAU) on BG/P Systems References TAU Project Site TAU Instrumentation Methods TAU Compilation Options TAU Fortran Instrumentation FAQ TAU Leap to Petascale 2009 Presentation TAU Workshop 2009 Introduction The TAU (Tuning and Analysis Utilities) Performance System is a portable profiling and tracing toolkit for performance analysis of parallel programs written in Fortran, C, C++, Java, Python. TAU gathers performance information while a program executes through instrumentation of functions, methods, basic blocks, and statements. The instrumentation consists of calls to TAU library routines which can be incorporated into a program in several ways: automatic instrumentation of the code at the source level using the Program Database Toolkit (PDT)

318

Advanced turbine systems program conceptual design and product development. Quarterly report, February 1995--April 1995  

SciTech Connect

This Quarterly Technical Progress Report covers the period February 1, 1995, through April 30, 1995, for Phase II of the Advanced Turbine Systems (ATS) Program by Solar Turbines Incorporated under DOE contract No. DE-AC21-93MC30246. The objective of Phase II of the ATS Program is to provide the conceptual design and product development plan for an ultra high efficiency, environmentally superior and cost competitive industrial gas turbine system to be commercialized by the year 2000. A secondary objective is to begin early development of technologies critical to the success of ATS. Tasks 1, 2, 3, 5, 6 and 7 of Phase II have been completed in prior quarters. Their results have been discussed in the applicable quarterly reports and in their respective topical reports. With the exception of Task 7, final editions of these topical reports have been submitted to the DOE. This quarterly report, then, addresses only Task 4 and the nine subtasks included in Task 8, {open_quotes}Design and Test of Critical Components.{close_quotes} These nine subtasks address six ATS technologies as follows: (1) Catalytic Combustion - Subtasks 8.2 and 8.5, (2) Recuperator - Subtasks 8.1 and 8.7, (3) Autothermal Fuel Reformer - Subtask 8.3, (4) High Temperature Turbine Disc - Subtask 8.4, (5) Advanced Control System (MMI) - Subtask 8.6, and (6) Ceramic Materials - Subtasks 8.8 and 8.9. Major technological achievements from Task 8 efforts during the quarter are as follows: (1) The subscale catalytic combustion rig in Subtask 8.2 is operating consistently at 3 ppmv of NO{sub x} over a range of ATS operating conditions. (2) The spray cast process used to produce the rim section of the high temperature turbine disc of Subtask 8.4 offers additional and unplanned spin-off opportunities for low cost manufacture of certain gas turbine parts.

Karstensen, K.W.

1995-07-01T23:59:59.000Z

319

Computer System,  

NLE Websites -- All DOE Office Websites (Extended Search)

undergraduate summer institute http:institutes.lanl.govistisummer-school 2015 Computer System, Cluster, and Networking Summer Institute Purpose The Computer System,...

320

IODP Expedition 342: Paleogene Newfoundland Sediment Drifts Week 1 Report (1-9 June 2012)  

E-Print Network (OSTI)

and pressure signals were successfully transmitted to the rig floor and recorded. After circulation was re from the hole. The bit cleared the rotary table at 0110 h ending Hole U1402A. #12;Since barrel on the rig floor and placed into split liner sections. The coring system was disassembled

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Hanford Environmental Information System (HEIS) Operator`s Manual. Volume 1  

SciTech Connect

The Hanford Environmental Information System (HEIS) is a consolidated set of automated resources that effectively manage the data gathered during environmental monitoring and restoration of the Hanford Site. The HEIS includes an integrated database that provides consistent and current data to all users and promotes sharing of data by the entire user community. This manual describes the facilities available to the operational user who is responsible for data entry, processing, scheduling, reporting, and quality assurance. A companion manual, the HEIS User`s Manual, describes the facilities available-to the scientist, engineer, or manager who uses the system for environmental monitoring, assessment, and restoration planning; and to the regulator who is responsible for reviewing Hanford Site operations against regulatory requirements and guidelines.

Schreck, R.I.

1991-10-01T23:59:59.000Z

322

Dynamic Response of a Rotor-air Bearing System Due to Base Induced Periodic Motions  

E-Print Network (OSTI)

.............................................................. 20 Typical base motion induced accelerations..................................... 20 Rotor speed coast down tests .......................................................... 22... ............................................................. 16 6 Photograph of connection of shaker to test rig base plate.......................... 17 7 Typical measured base acceleration in time domain. Shaker excitation frequency: 6 Hz. Rotor speed = 34 krpm (567 Hz...

Niu, Yaying

2010-01-14T23:59:59.000Z

323

Systems Synthesis  

NLE Websites -- All DOE Office Websites (Extended Search)

Synthesis. Integration, and Control System synthesis, integration, and control requires creativity and a broad vision of the big picture of the system to be able to select the best...

324

File Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

File Systems File Systems File Systems For a general description of the different file systems available on PDSF please see Eliza File Systems and Other File Systems. Below is a summary of how STAR uses the various systems: /common The STAR software is installed on /common. For 32sl44 it is under /common/star/star44 and for sl53 it is under /common/star/star53. In both cases the software consists primarily of a STAR-specific ROOT installation on which releases of the STAR libraries are built as shown on the Local STAR Libraries page. /eliza3, /eliza6, /eliza9, /eliza14, /eliza15, /eliza17 STAR has space on 6 elizas as shown in the table below. File System star space (TB) use eliza3 39 production eliza6 9 production eliza9 39 production eliza14 34 production, user space under /eliza14/star/pwg

325

Advanced Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Systems: Advanced Systems: high Performance fenestration systems Research areas: Research activities to improve the performance of windows and other fenestration products must address window systems issues as well as Glazing Materials research. LBNL activities in the area of Advanced Systems include research at both the product level and the building envelope and building systems levels. Highly insulating windows - using non structural center layers Lower cost solutions to more insulating three layer glazing systems, with the potential to turn windows in U.S. heating dominated residential applications into net-energy gainers. Highly Insulating Window Frames In collaboration with the Norwegian University of Science and Technology, we are researching the potentials for highly insulating window frames. Our initial work examines European frames with reported U-factors under 0.15 Btu/hr-ft2-F. Future research aims to analyze these designs, verify these performance levels and ensure that procedures used to calculate frame performance are accurate.

326

Microfluidic Systems Integrated Microfluidic Systems**  

E-Print Network (OSTI)

Microfluidic Systems Integrated Microfluidic Systems** Rustem F. Ismagilov* Keywords: analytical methods · enzymes · microfluidics · microreactors · protein structures Microfluidic systems use networks of channels thinner than a human hair to manipulate nanoliter volumes of re- agents. The goal of microfluidics

Ismagilov, Rustem F.

327

Performance of a Dynamically Controlled Inverter in a Photovoltaic System Interconnected with a Secondary Network Distribution System  

SciTech Connect

In 2008, a 300 kW{sub peak} photovoltaic (PV) system was installed on the rooftop of the Colorado Convention Center (CCC). The installation was unique for the electric utility, Xcel Energy, as it had not previously permitted a PV system to be interconnected on a building served by the local secondary network distribution system (network). The PV system was installed with several provisions; one to prevent reverse power flow, another called a dynamically controlled inverter (DCI), that curtails the output of the PV inverters to maintain an amount of load supplied by Xcel Energy at the CCC. The DCI system utilizes current transformers (CTs) to sense power flow to insure that a minimum threshold is maintained from Xcel Energy through the network transformers. The inverters are set to track the load on each of the three phases and curtail power from the PV system when the generated PV system current reaches 95% of the current on any phase. This is achieved by the DCI, which gathers inputs from current transformers measuring the current from the PV array, Xcel, and the spot network load. Preventing reverse power flow is a critical technical requirement for the spot network which serve this part of the CCC. The PV system was designed with the expectation that the DCI system would not curtail the PV system, as the expected minimum load consumption was historically higher than the designed PV system size. However, the DCI system has operated many days during the course of a year, and the performance has been excellent. The DCI system at the CCC was installed as a secondary measure to insure that a minimum level of power flows to the CCC from the Xcel Energy network. While this DCI system was intended for localized control, the system could also reduce output percent if an external smart grid control signal was employed. This paper specifically focuses on the performance of the innovative design at this installation; however, the DCI system could also be used for new s- art grid-enabled distribution systems where renewables power contributions at certain conditions or times may need to be curtailed.

Coddington, M. H.; Kroposki, B. D.; Basso, T.; Berger, D.; Crowell, K.; Hayes, J.

2011-01-01T23:59:59.000Z

328

VXIbus based optical transducer evaluation system  

SciTech Connect

The Bonneville Power Administration (BPA) recently undertook an investigation into using new fiber optic based Potential Transducers and Current Transducers (PT and CT) in their power system. This paper describes the Data Acquisition System (DAS) and associated hardware developed to gather information on the Optical devices performance in the field. Bonneville currently uses PT and CT devices based on magnetic principles that have been in operation for over 40 years. Some disadvantages in the current magnetic devices include their large size, the internal usage of oils some of which are hazardous PCBs, a requirement for connection to instrumentation through substation analog connections, and occasional explosive breakdowns which can injure workers. The main advantage to this technology is a well proven operational history. A few manufacturers have recently developed PT and CT devices based on fiber optics which solve many of the problems associated with the magnetic devices. They are lightweight, use no oils, and are connected to instrumentation through non conductive fiber optics. However, they are new technology, and have seen limited practical application. The BPA Laboratory Services first tested the performance of the optical devices selected for this test in the controlled environment of the laboratory. They were energized from well characterized sources and the output parameters such as accuracy, drift, and noise floor were measured with standard rack type test instrumentation. Once fully tested and calibrated in the laboratory, the optical devices were then installed at Keeler substation in Hillsboro Oregon on a 500KV bus to be evaluated in real world conditions. The optical transducers were connected to standard BPA meters and relays for this test. Some of the meters were modified to accept the low voltage outputs of the optical devices.

Tillett, J. [Bonneville Power Administration, Vancouver, WA (United States)

1995-12-31T23:59:59.000Z

329

Carbon Systems  

SciTech Connect

The electronic states of a 'quantum dot-graphene monolayer-SiO{sub 2} + n{sup +}-Si substrate' system in an external magnetic field are studied. An analytical expression for charge transfer in this system is obtained. The electronic states of a 'quantum dot-graphene bilayer-SiO{sub 2} + n{sup +}-Si substrate' system are considered. The systems under study are interesting from the viewpoint of controlling the optical properties of a quantum dot by means of an applied electric field.

Alisultanov, Z. Z., E-mail: zaur0102@gmail.com [Russian Academy of Sciences, Prokhorov General Physics Institute (Russian Federation)

2013-06-15T23:59:59.000Z

330

Muon systems  

SciTech Connect

The designs of both the GEM and SDC muon systems an the technological choices are reviewed. In particular, the chamber options for the detectors are discussed.

Bensinger, J.

1991-10-01T23:59:59.000Z

331

Dissemination and visualisation of earth system models for the Dutch subsurface  

Science Journals Connector (OSTI)

For more than a century, geological surveys have gathered a great amount of subsurface data. Within the last decade, major technological advancements have revolutionised geoscience interpretations. Multidiscip...

Jan-Diederik van Wees; Rob Versseput…

2003-01-01T23:59:59.000Z

332

Energy information systems (EIS): Technology costs, benefit, and best practice uses  

E-Print Network (OSTI)

interviews, and gathering energy and cost data. Similarly,of an EIS? Quantifying the energy and cost-savings benefitssystems enable building energy and cost savings in three

Granderson, Jessica

2014-01-01T23:59:59.000Z

333

Investigating and establishing limiting heat flux for passively cooled and solar concentrated thermoelectric power generation system.  

E-Print Network (OSTI)

??Thermoelectric generators (TEG) working on the principle of Seebeck effect have gathered the attention during this period as a potential device that can generate electricity… (more)

Date, A

2014-01-01T23:59:59.000Z

334

Power system  

DOE Patents (OSTI)

A power system includes a prime mover, a transmission, and a fluid coupler having a selectively engageable lockup clutch. The fluid coupler may be drivingly connected between the prime mover and the transmission. Additionally, the power system may include a motor/generator drivingly connected to at least one of the prime mover and the transmission. The power-system may also include power-system controls configured to execute a control method. The control method may include selecting one of a plurality of modes of operation of the power system. Additionally, the control method may include controlling the operating state of the lockup clutch dependent upon the mode of operation selected. The control method may also include controlling the operating state of the motor/generator dependent upon the mode of operation selected.

Hickam, Christopher Dale (Glasford, IL)

2008-03-18T23:59:59.000Z

335

Performance Tools and APIs on BG/P Systems | Argonne Leadership Computing  

NLE Websites -- All DOE Office Websites (Extended Search)

Performance Tools and APIs Performance Tools and APIs Tuning and Analysis Utilities (TAU) Rice HPC Toolkit IBM HPCT Mpip gprof Profiling Tools Darshan PAPI High Level UPC API Low Level UPC API UPC Hardware BG/P dgemm Performance Tuning MPI on BGP Performance FAQs IBM References Software and Libraries Tukey Eureka / Gadzooks Policies Documentation Feedback Please provide feedback to help guide us as we continue to build documentation for our new computing resource. [Feedback Form] Performance Tools and APIs on BG/P Systems MPI and OpenMP Options Tuning MPI on BGP Performance Tools Tuning and Analysis Utilities (TAU) - Instruments applications and gathers information on timings, MPI activity, and hardware performance counter events Rice HPCToolkit- Performs sample based profiling of applications and

336

T3: Secure, Scalable, Distributed Data Movement and Remote System Control for Enterprise Level Cyber Security  

SciTech Connect

Enterprise level cyber security requires the deployment, operation, and monitoring of many sensors across geographically dispersed sites. Communicating with the sensors to gather data and control behavior is a challenging task when the number of sensors is rapidly growing. This paper describes the system requirements, design, and implementation of T3, the third generation of our transport software that performs this task. T3 relies on open source software and open Internet standards. Data is encoded in MIME format messages and transported via NNTP, which provides scalability. OpenSSL and public key cryptography are used to secure the data. Robustness and ease of development are increased by defining an internal cryptographic API, implemented by modules in C, Perl, and Python. We are currently using T3 in a production environment. It is freely available to download and use for other projects.

Thomas, Gregory S.; Nickless, William K.; Thiede, David R.; Gorton, Ian; Pitre, Bill J.; Christy, Jason E.; Faultersack, Elizabeth M.; Mauth, Jeffery A.

2009-07-20T23:59:59.000Z

337

U.S. Crude Oil and Natural Gas Active Well Service Rigs in operation  

Gasoline and Diesel Fuel Update (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 1,549 1,677 1,805 1,898 1,991 1,994 1,997 2,112 2,227 2,247 2,266 2,334 1974 2,401 2,436 2,470 2,513 2,555 2,525 2,494 2,483 2,473 2,488 2,503 2,543 1975 2,582 2,549 2,568 2,549 2,374 2,426 2,344 2,369 2,459 2,434 2,505 2,675 1976 2,612 2,490 2,521 2,597 2,575 2,607 2,606 2,656 2,652 2,639 2,601 2,660 1977 2,474 2,628 2,695 2,804 2,760 2,895 2,929 2,942 2,964 2,973 2,968 2,898 1978 2,810 2,906 2,899 2,997 2,996 2,987 3,006 3,089 3,073 3,078 2,958 3,063 1979 3,094 2,698 2,765 3,034 3,369 3,506 3,572 3,621 3,673 3,954 3,795 3,709 1980 3,855 3,923 4,010 3,871 4,032 4,112 4,092 4,155 4,277 4,290 4,281 4,172

338

Numerical and experimental determination of neutron characteristics in irradiation rigs operated in LVR-15 research reactor  

Science Journals Connector (OSTI)

......conditions including neutron fluence and its energy distribution...similar to fission and fusion...presence of neutron and gamma radiation...degradation induced by radiation...fluence and its energy distribution...information on thermal neutron fluence...calculated spectrum is appropriate......

Michal Koleska; Ladislav Viererbl; Zdena Lahodova; Jaroslav Ernest; Jelena Zmitkova; Milan Marek

2014-10-01T23:59:59.000Z

339

Chemical Looping Autothermal Reforming at a 120 kW Pilot Rig  

Science Journals Connector (OSTI)

Chemical looping with selective oxygen transport allows two step combustion or autothermal reforming without mixing of fuel...4...conversion is achieved. Air/fuel ratio is varied at three different fuel reactor t...

Johannes Bofhàr-Nordenkampf; Tobias Pröll…

2010-01-01T23:59:59.000Z

340

Semi-submersible rigs: a vector transporting entire marine communities around the world  

Science Journals Connector (OSTI)

On 5 March 2006, the tug Mighty Deliverer...departed from Macae, Brazil for Singapore, towing the decommissioned, semi-submersible petrochemical production platform (hereafter referred to in the generic ‘...A Tur...

Ross M. Wanless; Sue Scott; Warwick H. H. Sauer; Timothy G. Andrew…

2010-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Experimental evaluation of a metal-mesh bearing damper in a high speed test rig  

E-Print Network (OSTI)

and power turbine rotors. To design the metal mesh damper, static stiffness and dynamic rap test measurements were first made on metal mesh samples in a specially designed non-rotating test fixture. These property tests were performed on samples of various...

Zarzour, Mark Joseph

1999-01-01T23:59:59.000Z

342

U.S. Crude Oil Rotary Rigs in Operation (Number of Elements)  

Gasoline and Diesel Fuel Update (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 NA NA NA NA NA NA NA NA NA NA NA NA 1974 NA NA NA NA NA NA NA NA NA NA NA NA 1975 NA NA NA NA NA NA NA NA NA NA NA NA 1976...

343

U.S. Natural Gas Rotary Rigs in Operation (Number of Elements...  

Gasoline and Diesel Fuel Update (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1970's NA NA NA NA NA NA NA 1980's NA NA NA NA NA NA NA NA 354 401 1990's 464 351 331 364 427 385 464...

344

U.S. Onshore Crude Oil and Natural Gas Rotary Rigs in Operation...  

Gasoline and Diesel Fuel Update (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 1,120 1,037 959 914 974 1,042 1,075 1,140 1,183 1,250 1,304 1,318 1974 1,283 1,264 1,272 1,280 1,319 1,342 1,387 1,426...

345

U.S. Crude Oil Rotary Rigs in Operation (Number of Elements)  

Annual Energy Outlook 2012 (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1970's NA NA NA NA NA NA NA 1980's NA NA NA NA NA NA NA NA 554 453 1990's 532 482 373 373 335 323 306...

346

U.S. Natural Gas Rotary Rigs in Operation (Number of Elements...  

Gasoline and Diesel Fuel Update (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 NA NA NA NA NA NA NA NA NA NA NA NA 1974 NA NA NA NA NA NA NA NA NA NA NA NA 1975 NA NA NA NA NA NA NA NA NA NA NA NA 1976...

347

U.S. Crude Oil and Natural Gas Rotary Rigs in Operation (Number...  

Annual Energy Outlook 2012 (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 1,219 1,126 1,049 993 1,046 1,118 1,156 1,222 1,266 1,334 1,390 1,405 1974 1,372 1,355 1,367 1,381 1,413 1,432 1,480 1,518...

348

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation...  

Annual Energy Outlook 2012 (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 99 89 90 79 72 76 81 82 83 84 86 87 1974 89 91 95 101 94 90 93 92 90 91 99 103 1975 94 93 102 102 102 106 109 112 113 112...

349

U.S. Crude Oil and Natural Gas Rotary Rigs in Operation (Number...  

Gasoline and Diesel Fuel Update (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1940's 2,017 1950's 2,154 2,543 2,641 2,613 2,508 2,686 2,620 2,426 1,922 2,071 1960's 1,748 1,761...

350

U.S. Onshore Crude Oil and Natural Gas Rotary Rigs in Operation...  

Annual Energy Outlook 2012 (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1940's NA 1950's NA NA NA NA NA NA NA NA NA NA 1960's NA NA NA NA NA NA NA NA NA NA 1970's NA NA NA...

351

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation...  

Annual Energy Outlook 2012 (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1940's NA 1950's NA NA NA NA NA NA NA NA NA NA 1960's NA NA NA NA NA NA NA NA NA NA 1970's NA NA NA 84...

352

Above Ground Geothermal and Allied Technologies Masters Scholarship in Energy & Materials: design of a rig  

E-Print Network (OSTI)

Above Ground Geothermal and Allied Technologies Masters Scholarship in Energy & Materials: design into the largest green energy resources; industrial waste heat, biomass combustion and geothermal energy. Research of geothermal energy after completing the degree. Proficiency in English is essential. Contact: mark

Hickman, Mark

353

Microsoft Word - Tilted-Rig-TP-Definition-Version1-Aug-14-2012A...  

NLE Websites -- All DOE Office Websites (Extended Search)

motion that produces a rising plume (spike) on the left, and falling plume (bubble) on the right, that are almost symmetric; and 2) a Rayleigh-Taylor driven mixing...

354

DOE/RL-92-36, Hanford Site Hoisting and Rigging Manual APPENDIX...  

NLE Websites -- All DOE Office Websites (Extended Search)

to comply with the requirements of this manual and referenced Department of Energy (DOE), Occupational Safety and Health Administration (OSHA), and American Society of...

355

The rig of the eleventh-century ship at Serce Liman, Turkey  

E-Print Network (OSTI)

, Rick Green, Faith Henchel, Peggy Leshikar, Pilar Luna, Robin and Netia Piercy, Cemal and Sema Pulak, Lisa Shuey, Bruce Thompson and a special thanks to Alison Darroch. To Dr. Fife and all the people at the Texas ASM Hyperbaric Laboratory, I extend...

Matthews, Sheila Diane

1983-01-01T23:59:59.000Z

356

Water geochemistry of hydrothermal systems, Wood River District, Idaho  

SciTech Connect

Hydrothermal systems of the Wood River District, central Idaho, have been studied by geologic mapping of thermal spring areas and geochemical investigations of thermal and non-thermal waters. This report summarizes the new geochemical data gathered during the study. Integration of the results of geological and geochemical studies has led to development of a target model for hydrothermal resources on the margin of the Idaho Batholith. Warfield Hot Springs, with temperatures up to 58/sup 0/C, flow from a major shear zone along the margin of an apophysis of the batholith. Hailey Hot Springs, with temperatures up to 60/sup 0/C, occur in an area of multiple thrust faults and newly recognized, closely spaced normal faults in the Paleozoic Milligen and Wood River Formations, 2.5 km from a highly brecciated batholith contact. Other Wood River district hydrothermal systems also occur along the margins of batholith apophyses or in adjacent highly fractured Paleozoic rocks, where there are indications of batholith rocks at shallow depths (100 to 300 m) in water wells.

Zeisloft, J.; Foley, D.; Blackett, R.

1983-08-01T23:59:59.000Z

357

telecommunications system management  

Science Journals Connector (OSTI)

Communications system management applied to telecommunications systems, facilities, equipment, and components. See communications system , comm...

2001-01-01T23:59:59.000Z

358

Reversible Bending Fatigue Test System for Investigating Vibration Integrity of Spent Nuclear Fuel during Transportation  

SciTech Connect

Transportation packages for spent nuclear fuel (SNF) must meet safety requirements under normal and accident conditions as specified by federal regulations. During transportation, SNF experiences unique conditions and challenges to cladding integrity due to the vibrational and impact loading during road or rail shipment. Oak Ridge National Laboratory (ORNL) has been developing testing capabilities that can be used to improve the understanding of the impacts on SNF integrity due to vibration loading, especially for high burn-up SNF in normal transportation operation conditions. This information can be used to meet the nuclear industry and U.S. Nuclear Regulatory Commission needs in the area of safety and security of spent nuclear fuel storage and transport operations. The ORNL developed test system can perform reversible-bending fatigue testing to evaluate both the static and dynamic mechanical response of SNF rods under simulated loads. The testing apparatus is also designed to meet the challenges of hot-cell operation, including remote installation and detachment of the SNF test specimen, in-situ test specimen deformation measurement, and implementation of a driving system suitable for use in a hot cell. The system contains a U-frame set-up equipped with uniquely designed grip rigs, to protect SNF rod and to ensure valid test results, and use of 3 specially designed LVDTs to obtain the in-situ curvature measurement. A variety of surrogate test rods have been used to develop and calibrate the test system as well as in performing a series of systematic cyclic fatigue tests. The surrogate rods include stainless steel (SS) cladding, SS cladding with cast epoxy, and SS cladding with alumina pellets inserts simulating fuel pellets. Testing to date has shown that the interface bonding between the SS cladding and the alumina pellets has a significant impact on the bending response of the test rods as well as their fatigue strength. The failure behaviors observed from tested surrogate rods provides a fundamental understanding of the underlying failure mechanisms of the SNF surrogate rod under vibration which has not been achieved previously. The newly developed device is scheduled to be installed in the hot-cell in summer 2013 to test high burnup SNF.

Wang, Jy-An John [ORNL] [ORNL; Wang, Hong [ORNL] [ORNL; Bevard, Bruce Balkcom [ORNL] [ORNL; Howard, Rob L [ORNL] [ORNL; Flanagan, Michelle [U.S. Nuclear Regulatory Commission] [U.S. Nuclear Regulatory Commission

2013-01-01T23:59:59.000Z

359

LRRB Pavement Management Systems Pavement Management Systems  

E-Print Network (OSTI)

LRRB Pavement Management Systems Pavement Management Systems Presented by: Michael Marti SRF for implementing and monitoring research results (RIC) #12;LRRB Pavement Management Systems LRRB Structure LRRB Current Pavement Management System Used ICON (Goodpointe) Year of Pavement Management System

Minnesota, University of

360

Disposal systems evaluations and tool development : Engineered Barrier System (EBS) evaluation.  

SciTech Connect

Key components of the nuclear fuel cycle are short-term storage and long-term disposal of nuclear waste. The latter encompasses the immobilization of used nuclear fuel (UNF) and radioactive waste streams generated by various phases of the nuclear fuel cycle, and the safe and permanent disposition of these waste forms in geological repository environments. The engineered barrier system (EBS) plays a very important role in the long-term isolation of nuclear waste in geological repository environments. EBS concepts and their interactions with the natural barrier are inherently important to the long-term performance assessment of the safety case where nuclear waste disposition needs to be evaluated for time periods of up to one million years. Making the safety case needed in the decision-making process for the recommendation and the eventual embracement of a disposal system concept requires a multi-faceted integration of knowledge and evidence-gathering to demonstrate the required confidence level in a deep geological disposal site and to evaluate long-term repository performance. The focus of this report is the following: (1) Evaluation of EBS in long-term disposal systems in deep geologic environments with emphasis on the multi-barrier concept; (2) Evaluation of key parameters in the characterization of EBS performance; (3) Identification of key knowledge gaps and uncertainties; and (4) Evaluation of tools and modeling approaches for EBS processes and performance. The above topics will be evaluated through the analysis of the following: (1) Overview of EBS concepts for various NW disposal systems; (2) Natural and man-made analogs, room chemistry, hydrochemistry of deep subsurface environments, and EBS material stability in near-field environments; (3) Reactive Transport and Coupled Thermal-Hydrological-Mechanical-Chemical (THMC) processes in EBS; and (4) Thermal analysis toolkit, metallic barrier degradation mode survey, and development of a Disposal Systems Evaluation Framework (DSEF). This report will focus on the multi-barrier concept of EBS and variants of this type which in essence is the most adopted concept by various repository programs. Empasis is given mainly to the evaluation of EBS materials and processes through the analysis of published studies in the scientific literature of past and existing repository research programs. Tool evaluations are also emphasized, particularly on THCM processes and chemical equilibria. Although being an increasingly important aspect of NW disposition, short-term or interim storage of NW will be briefly discussed but not to the extent of the EBS issues relevant to disposal systems in deep geologic environments. Interim storage will be discussed in the report Evaluation of Storage Concepts FY10 Final Report (Weiner et al. 2010).

Rutqvist, Jonny (LBNL); Liu, Hui-Hai (LBNL); Steefel, Carl I. (LBNL); Serrano de Caro, M. A. (LLNL); Caporuscio, Florie Andre (LANL); Birkholzer, Jens T. (LBNL); Blink, James A. (LLNL); Sutton, Mark A. (LLNL); Xu, Hongwu (LANL); Buscheck, Thomas A. (LLNL); Levy, Schon S. (LANL); Tsang, Chin-Fu (LBNL); Sonnenthal, Eric (LBNL); Halsey, William G. (LLNL); Jove-Colon, Carlos F.; Wolery, Thomas J. (LLNL)

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Natural System  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Natural System Natural System Evaluation and Tool Development - FY11 Progress Report Prepared for U.S. Department of Energy Used Fuel Disposition Program Yifeng Wang (SNL) Michael Simpson (INL) Scott Painter (LANL) Hui-Hai Liu (LBNL) Annie B. Kersting (LLNL) July 15, 2011 FCRD-USED-2011-000223 UFD Natural System Evaluation - FY11 Year-End Report July 15, 2011 2 DISCLAIMER This information was prepared as an account of work sponsored by an agency of the U.S. Government. Neither the U.S. Government nor any agency thereof, nor any of their employees, makes any warranty, expressed or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness, of any information, apparatus, product, or process disclosed, or represents that its use would not infringe

362

Lighting Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Purple LED lamp Purple LED lamp Lighting Systems Lighting research is aimed at improving the energy efficiency of lighting systems in buildings and homes across the nation. The goal is to reduce lighting energy consumption by 50% over twenty years by improving the efficiency of light sources, and controlling and delivering illumination so that it is available, where and when needed, and at the required intensity. Research falls into four main areas: Sources and Ballasts, Light Distribution Systems, Controls and Communications, and Human Factors. Contacts Francis Rubinstein FMRubinstein@lbl.gov (510) 486-4096 Links Lighting Research Group Batteries and Fuel Cells Buildings Energy Efficiency Applications Commercial Buildings Cool Roofs and Heat Islands Demand Response Energy Efficiency Program and Market Trends

363

More Than 180 People Gather for Women of Waste Management Event...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

the event for the fifth consecutive year, presented a check for 10,000 to the Breast Cancer Research Foundation. The foundation's Heather Story Steiness, a breast cancer...

364

A criminological analysis : using real-time monitoring to gather data on online predators.  

E-Print Network (OSTI)

??The Internet presents a constantly evolving frontier for criminology and policing, especially in relation to online predators – paedophiles operating within the Internet for safer… (more)

Jayawardena, Kasun P.

2011-01-01T23:59:59.000Z

365

Chemists get a taste of life at gathering in San Diego  

Science Journals Connector (OSTI)

...from micrometer-sized algae like these diatoms can be turned into biodiesel. teins, but when starved...esterification turns algae oil into a die-sel-like...Luckily, soybean biodiesel has already surmounted...help open the way for algae oil to flow into consumers...

F Flam

1994-04-01T23:59:59.000Z

366

Chemists get a taste of life at gathering in San Diego  

Science Journals Connector (OSTI)

...National Renewable Energy Laboratory in Golden...correct source of oil: algae. Now, you might...applications for algae oil-as industrial...have worked in the alternative fuels game. After...Holmberg ofthe American Biofuels Associa-tion...open the way for algae oil to flow into...

F Flam

1994-04-01T23:59:59.000Z

367

Summer Cattle Transhumance and Wild Edible Plant Gathering in a Mapuche Community of Northwestern Patagonia  

Science Journals Connector (OSTI)

Cattle transhumance has been practiced since colonial times in Mapuche communities of northwestern Patagonia, which travelled seasonally along the Andean valleys from arid lands towards temperate forests. In t...

Ana H. Ladio; Mariana Lozada

2004-04-01T23:59:59.000Z

368

LBN: Load-Balancing Network for Data Gathering Wireless Sensor Networks  

Science Journals Connector (OSTI)

Hotspots of energy consumption and network congestions can be caused by load imbalance among sensor nodes in wireless sensor networks. This may lead to loss of data packets and premature death of sensor nodes ......

Wenlu Yang; Chongqing Zhang; Minglu Li

2006-01-01T23:59:59.000Z

369

Probabilistic Planning with Information Gathering and Contingent Denise Draper Steve Hanks Daniel Weld  

E-Print Network (OSTI)

Example Suppose that a manufacturing robot is given the goal of having a widget painted (PA), processed by rejecting (reject) parts that are awed (FL) or shipping (ship) parts that are not awed (FL). The robot also has an action paint that usually makes PA true, and an action notify that makes NO true. Initially

370

Poster Abstract: Exposing Two Critical Myths about Correlation Aware Data Aggregation I. CORRELATION AWARE DATA GATHERING  

E-Print Network (OSTI)

aware aggregation trees (CAATs). In this paper, we study the energy efficiency of CAATs from a new energy-delay tradeoff from the perspective of aggregation tree structures. Intuitively, with a higher ap, thereby resulting in an aggregation tree with lower energy cost. Therefore, the energy improvement tends

Sivakumar, Raghupathy

371

Traditional Diet and Food Preferences of Australian Aboriginal Hunter-Gatherers [and Discussion  

Science Journals Connector (OSTI)

29 November 1991 research-article Traditional...traditional foods had a low energy density but high density...some nutrients. The low energy density of the diet and...natural constraint on energy intake.(ABSTRACT TRUNCATED AT 250 WORDS...

1991-01-01T23:59:59.000Z

372

State of the Art and the Prospects for Data Gathering, Storage, Transformation, and Retrieval  

Science Journals Connector (OSTI)

...and FRIGID ROOMS WIDE HUMIDITY RANGES MODULAR "PANELIZED" FIBERGLASS ROOMS PLANT GROWTH ROOMS COLD CABINETS EXPLOSION-PROOF REFRIGERATORS REACH-IN CO2 CHAMBERS NEW SOLID STATE...temperature range. O900 Series Rooms. New, modular, sandwich-type panels of 2-inch...

J. C. R. Lucklider

1966-02-18T23:59:59.000Z

373

Automated Gathering of Web Information: An In-Depth Examination of Agents Interacting  

E-Print Network (OSTI)

Engines BERNARD J. JANSEN, TRACY MULLEN The Pennsylvania State University AMANDA SPINK The University: Search engines, Web searching, agent searching Authors' addresses: B.J. Jansen, and T. Mullen¨olscher and Strube 2000; Jansen and Pooch 2001; Spink et al. 2002], providing insights into how humans conduct Web

Jansen, James

374

On the Benefit of using Tight Frames for Robust Data Transmission and Compressive Data Gathering  

E-Print Network (OSTI)

property (RIP), which represents a sufficient condition for successful reconstruction of the signals [4

Cambridge, University of

375

Reencuentro Ayacucho ´88: The 8th International Gathering of Group Theatre  

E-Print Network (OSTI)

, Raíces, Teatro del Sol and Yuyachkani. The director and founder of Cuatrotablas, Mario Delgado Vásquez led all of the groups. The majority of groups came from Lima and the regional centers of Peru; however, the Reencuentro also included groups from... in the encuentro included from Lima: Cuatrotablas, Centro de Comunicación de Villa El Salvador, Magia, Raíces, Teatro del Sol, and Yuyachkani; from the Peruvian provinces: Algovipasar (Cajamarca), Arlequín (Huánuco), Audaces (Arequipa), José María Arguedas...

Watson, Ian

1990-04-01T23:59:59.000Z

376

Dozer: Ultra-Low Power Data Gathering in Sensor Networks Nicolas Burri  

E-Print Network (OSTI)

and Networks Laboratory ETH Zurich 8092 Zurich, Switzerland nburri@tik.ee.ethz.ch Pascal von Rickenbach Computer Engineering and Networks Laboratory ETH Zurich 8092 Zurich, Switzerland pascalv@tik.ee.ethz.ch Roger Wattenhofer Computer Engineering and Networks Laboratory ETH Zurich 8092 Zurich, Switzerland

Gummadi, Ramakrishna

377

NAS-NAE National Convocation on "Rising Above the Gathering Storm...  

Energy Savers (EERE)

fortunate position of "preaching to the choir" today. After all, there are few things we care more passionately about than the need to strengthen America's position in the world...

378

Gathering data on allegations of sexual abuse made against former disc jockey, Jimmy Savile   

E-Print Network (OSTI)

This paper will report on a collaboration between Social Work and Informatics academics and Library staff at the University. The focus of the work is to secure a data set on allegations of sexual abuse made against the former disc jockey, Jimmy...

Smith, Mark; Kirkwood, Steve; Llewellyn, Clare

2014-08-26T23:59:59.000Z

379

Do great tits assess rivals by combining direct experience with information gathered by eavesdropping?  

Science Journals Connector (OSTI)

...Sennheiser Proc. R. Soc. Lond. B (2002) electronic Gmbh & Co., Wedermark, Germany), AKB-11 pre- amplifiers (Audio Engineering Ltd, London, UK) and Marantz CP430 cassette recorders (Marantz Japan Inc., Sagamahira City, Japan). In total...

2002-01-01T23:59:59.000Z

380

Application of a Heat Integrated Post-combustion CO2 Capture System with Hitachi Advanced Solvent into Existing Coal-Fired Power Plant Award Number: DE-FE0007395 DOE Project Manager: José D. Figueroa  

NLE Websites -- All DOE Office Websites (Extended Search)

a Heat Integrated Post- a Heat Integrated Post- combustion CO 2 Capture System with Hitachi Advanced Solvent into Existing Coal-Fired Power Plant University of Kentucky Research Foundation Partnered with U.S. Department of Energy NETL Louisville Gas & Electric and Kentucky Utilities Electric Power Research Institute (with WorleyParsons) Hitachi Power Systems America Smith Management Group July 9, 2013 Goals and Objectives * Objectives 1) To demonstrate a heat-integrated post-combustion CO 2 capture system with an advanced solvent; 2) To collect information/data on material corrosion and identify appropriate materials of construction for a 550 MWe commercial-scale carbon capture plant.  To gather data on solvent degradation kinetics, water management, system dynamic control as well as other information during the long-term

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Odorization system upgrades gas utility`s pipelines  

SciTech Connect

Mountain Fuel Supply Co., a subsidiary of Questar Corp., salt Lake City, is a natural gas holding company with $1.6 billion in assets. From 1929 to 1984, Mountain Fuel Supply Co. owned and operated many natural gas wells, gathering systems, and transmission pipelines to serve its Utah and Wyoming customers. Gas is odorized at convenient points on the transmission lines and at each downstream location where unodorized gas entered the system. Since 40 to 60% of the gas delivered to the company`s customers passes through Coalville Station, it was vital that a reliable, state-of-the-art odorant station be constructed at this site. Construction began during the summer of 1994 and the system came on line Sept. 1, 1994. The station odorized 435 MMcfd with 330 lbs. of odorant during last winter`s peak day, a mild winter. Mountain Fuel is subject to Department of Transportation (DOT) codes which mandate that gas be readily detectable at one fifth the lower explosive limit (LEL), or about 1% gas in air. However, the company strives to maintain a readily detectable odor at 0.25% of gas in air as measured by odormeter tests throughout the distribution system. Experience has shown that maintaining an odorant injection rate of 0.75 lbs/MMcf provides adequate odor levels. A blend of odorant consisting of 50% tertiary butyl mercaptan (TBM) and 50% tetrahydrothiophene (THT) was used for many years by Questar Pipeline. Presently, it is used at all Mountain Fuel stations. This paper reviews the design and operation of this odorization station.

Niebergall, B. [Mountain Fuel Supply, Salt Lake City, UT (United States)

1995-07-01T23:59:59.000Z

382

A manual of recommended practices for hydrogen energy systems  

SciTech Connect

Technologies for the production, distribution, and use of hydrogen are rapidly maturing and the number and size of demonstration programs designed to showcase emerging hydrogen energy systems is expanding. The success of these programs is key to hydrogen commercialization. Currently there is no comprehensive set of widely-accepted codes or standards covering the installation and operation of hydrogen energy systems. This lack of codes or standards is a major obstacle to future hydrogen demonstrations in obtaining the requisite licenses, permits, insurance, and public acceptance. In a project begun in late 1996 to address this problem, W. Hoagland and Associates has been developing a Manual of Recommended Practices for Hydrogen Systems intended to serve as an interim document for the design and operation of hydrogen demonstration projects. It will also serve as a starting point for some of the needed standard-setting processes. The Manual will include design guidelines for hydrogen procedures, case studies of experience at existing hydrogen demonstration projects, a bibliography of information sources, and a compilation of suppliers of hydrogen equipment and hardware. Following extensive professional review, final publication will occur later in 1997. The primary goal is to develop a draft document in the shortest possible time frame. To accomplish this, the input and guidance of technology developers, industrial organizations, government R and D and regulatory organizations and others will be sought to define the organization and content of the draft Manual, gather and evaluate available information, develop a draft document, coordinate reviews and revisions, and develop recommendations for publication, distribution, and update of the final document. The workshop, Development of a Manual of Recommended Practices for Hydrogen Energy Systems, conducted on March 11, 1997 in Alexandria, Virginia, was a first step.

Hoagland, W.; Leach, S. [W. Hoagland and Associates, Boulder, CO (United States)

1997-12-31T23:59:59.000Z

383

System Verification II Systems Engineering  

E-Print Network (OSTI)

in safety critical systems to prevent unsafe values, e.g. high doses of radiation. Remember: not just should be able to: Explain the role & practice of debugging in the software process. Describe in detail the purpose, scope of, and activities comprising each of the three main phases of software testing. Conduct

Bryson, Joanna J.

384

Gasification Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

GASIFICATION SYSTEMS GASIFICATION SYSTEMS U.S. DEPARTMENT OF ENERGY TECHNOLOGY PROGRAM PLAN PREFACE ii DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference therein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any

385

Gasification system  

DOE Patents (OSTI)

A method and system for injecting coal and process fluids into a fluidized bed gasification reactor. Three concentric tubes extend vertically upward into the fluidized bed. Coal particulates in a transport gas are injected through an inner tube, and an oxygen rich mixture of oxygen and steam are injected through an inner annulus about the inner tube. A gaseous medium relatively lean in oxygen content, such as steam, is injected through an annulus surrounding the inner annulus.

Haldipur, Gaurang B. (Hempfield, PA); Anderson, Richard G. (Penn Hills, PA); Cherish, Peter (Bethel Park, PA)

1985-01-01T23:59:59.000Z

386

Gasification system  

DOE Patents (OSTI)

A method and system for injecting coal and process fluids into a fluidized bed gasification reactor. Three concentric tubes extend vertically upward into the fluidized bed. Coal particulates in a transport gas are injected through an inner tube, and an oxygen rich mixture of oxygen and steam are injected through an inner annulus about the inner tube. A gaseous medium relatively lean in oxygen content, such as steam, is injected through an annulus surrounding the inner annulus.

Haldipur, Gaurang B. (Hempfield, PA); Anderson, Richard G. (Penn Hills, PA); Cherish, Peter (Bethel Park, PA)

1983-01-01T23:59:59.000Z

387

Integrated System  

NLE Websites -- All DOE Office Websites (Extended Search)

Integrated Window System Our research activities in the field of high performance windows have led us to conclude that even by using high performance insulating glass units, low conductivity frames, and warm edge spacers, there are still untapped sources for improving energy efficiency in the design and use of residential windows. While such high performance windows are a dramatic improvement over conventional units, they do not reduce conductive losses through wall framing around the window, offer guarantees against excessive wall/window infiltration nor do they adapt to the daily and seasonal potentials for night insulation and summer shading. To meet this need, we have been working on the design, development, and prototyping of Integrated Window Systems (IWS) since 1993. Integrated Window Systems are a form of panelized construction where the wall panel includes an operable or fixed window sash, recessed night insulation, integral solar shading, and is built in a factory setting in order to minimize thermal short circuits and infiltration at joints. IWSs can be built in modular lengths to facilitate their installation with conventional wood frame stick construction or other forms of panelized construction.

388

Advanced Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Optimal gap width for double and triple glazing systems Optimal gap width for double and triple glazing systems Glazing systems in the US are commonly designed with a 1/2 " (12.7 mm) gap. The optimal gap width depends on many factors, such as gas fill (air, argon, krypton), the use of Low-e coatings, the environmental conditions (temperature difference across the window), and the calculation standard used. NFRC standard conditions are -18 C (-0.4 F) outside, and 21 C (69.8 F) inside. The calculation standard used in the US is based on the ISO 15099 standard. European standard conditions are 0 C (32 F) outside, and 20 C (68 F) inside. The calculation standard is based on the EN 673 standard. A number of common glazing configurations both with and without Low-e coatings, and with a variety of gas fills were evaluated using both the North American NFRC standard and the European EN 673 standard. All results were calculated using WINDOW 6.3 from LBNL. All IGU's (Insulated Glazing Units) have a standard height of 1 meter.

389

NETL: Coal Gasification Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Coal Gasification Systems News Gasifipedia Gasifier Optimization Feed Systems Syngas Processing Systems Analyses Gasification Plant Databases International Activity Program Plan...

390

Systems and Industry Analyses  

NLE Websites -- All DOE Office Websites (Extended Search)

systems and industry analyses News Gasifipedia Gasifier Optimization Feed Systems Syngas Processing Systems Analyses Gasification Plant Databases International Activity Program...

391

Power Systems Engineering  

NLE Websites -- All DOE Office Websites (Extended Search)

and distribution systems; steam, water, fuel, and environmental monitoring systems; alternative energy systems; reliability, availability, and maintainability assessments;...

392

Gasification Systems Project Portfolio  

NLE Websites -- All DOE Office Websites (Extended Search)

2014 Gasification Systems Project Portfolio News Gasifipedia Gasifier Optimization Feed Systems Syngas Processing Systems Analyses Gasification Plant Databases International...

393

Effects of reduced voltage on the operation and efficiency of electric systems. Volume 3. Field tests in a northern utility service area. Final report  

SciTech Connect

Volume 3 of this three-volume report for RP1419-1 describes the tests on selected residential, commercial, and small industry areas of the Detroit Edison Company system and the statistical analysis performed on the test data gathered. The purpose of the field testing was to provide data to analyze changes in energy consumption due to changes in feeder voltage levels. Detroit Edison was chosen to represent a winter peaking load area. Original intent was to present these results simultaneously with results from a summer peaking load area, Texas Electric Service Company (TESCO). Unavoidable delays retarded the Detroit study results to this Volume 3. TESCO results were reported in Volume 1, and the Distribution System Analysis and Simulation (DSAS) program for these studies was presented in Volume 2 in the form of a User's Manual.

Chen, M.S.; Shoults, R.R.

1985-07-01T23:59:59.000Z

394

Readiness Assessment for MF-628 Drum Treatment Facility - Advanced...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of all safety, process, and utility systems and support equipment will support the safe conduct of operations. MN. 1.4 Hoisting and rigging equipment, required for the activity...

395

Some perspectives on pulse detonation propulsion F.K. Lu and D.R. Wilson  

E-Print Network (OSTI)

chamber, a rotary valve injection system for three gas species (fuel, oxidizer and purge), an electric.62 cm section was used to support the mounting of the arc-plug igniter. A photograph of the test rig

Texas at Arlington, University of

396

Lawrence Berkeley Laboratory Institutional Plan FY 1993-98  

E-Print Network (OSTI)

ignition and combustible materials, rotating and reciprocating machinery, hoisting and rigging operations, lasers,ignition, reactivity, turbulence, and energy transfer in combustion systems. Advanced approaches include studies of photodissociation, laser

Chartock, Michael

2009-01-01T23:59:59.000Z

397

Hanford Environmental Information System (HEIS). Volume 1, User`s guide  

SciTech Connect

The Hanford Environmental Information System (HEIS) is a consolidated set of automated resources that effectively manage the data gathered during environmental monitoring and restoration of the Hanford Site. HEIS includes an integrated database that provides consistent and current data to all users and promotes sharing of data by the entire user community. HEIS is an information system with an inclusive database. Although the database is the nucleus of the system, HEIS also provides user access software: query-by-form data entry, extraction, and browsing facilities; menu-driven reporting facilities; an ad hoc query facility; and a geographic information system (GIS). These features, with the exception of the GIS, are described in this manual set. Because HEIS contains data from the entire Hanford Site, many varieties of data are included and have.been divided into subject areas. Related subject areas comprise several volumes of the manual set. The manual set includes a data dictionary that lists all of the fields in the HEIS database, with their definitions and a cross reference of their locations in the database; definitions of data qualifiers for analytical results; and a mapping between the HEIS software functions and the keyboard keys for each of the supported terminals or terminal emulators.

Not Available

1994-01-14T23:59:59.000Z

398

Paradigm shift in urban energy systems through distributed generation: Methods and models  

Science Journals Connector (OSTI)

The path towards energy sustainability is commonly referred to the incremental adoption of available technologies, practices and policies that may help to decrease the environmental impact of energy sector, while providing an adequate standard of energy services. The evaluation of trade-offs among technologies, practices and policies for the mitigation of environmental problems related to energy resources depletion requires a deep knowledge of the local and global effects of the proposed solutions. While attempting to calculate such effects for a large complex system like a city, an advanced multidisciplinary approach is needed to overcome difficulties in modeling correctly real phenomena while maintaining computational transparency, reliability, interoperability and efficiency across different levels of analysis. Further, a methodology that rationally integrates different computational models and techniques is necessary to enable collaborative research in the field of optimization of energy efficiency strategies and integration of renewable energy systems in urban areas. For these reasons, a selection of currently available models for distributed generation planning and design is presented and analyzed in the perspective of gathering their capabilities in an optimization framework to support a paradigm shift in urban energy systems. This framework embodies the main concepts of a local energy management system and adopts a multicriteria perspective to determine optimal solutions for providing energy services through distributed generation.

Massimiliano Manfren; Paola Caputo; Gaia Costa

2011-01-01T23:59:59.000Z

399

Development of a GIS-based monitoring and management system for underground coal mining safety  

Science Journals Connector (OSTI)

Coal mine safety is of paramount concern to mining industry. Mine accidents have various causes and consequences including catastrophic failure of mine, substantial economic losses and most notably loss of lives. Therefore, any initiative in mine monitoring is of vital importance for progressing safety surveillance and maintenance. This paper presents the development of a geographic information system (GIS)-based monitoring and management system for underground mine safety in three levels as constructive safety, surveillance and maintenance, and emergency. The developed model integrates the database design and management to the monitoring system implementation which encompasses query and analysis operations with the help of web and desktop applications. Interactive object-oriented graphical user interfaces (GUIs) were developed to visualize information about the entities gathered from the model and also to provide analysis operations based on the graphical representations and demonstrations using data tables and map objects. The research methodology essentially encompasses five main stages: (i) designing a conceptual database model; (ii) development of a logical model in terms of entity-relationship (ER) diagrams; (iii) development of a physical model based on physical constraints and requirements; (iv) development of \\{GUIs\\} and implementation of the developed model, analysis and queries; (v) verification and validation of the created model for Ömerler underground coal mine in Turkey. The proposed system is expected to be an efficient tool for improving and maintaining healthy standards in underground coal mines which can possibly be extended to a national GIS infrastructure.

Seda ?alap; Mahmut Onur Karsl?o?lu; Nuray Demirel

2009-01-01T23:59:59.000Z

400

Bearing system  

DOE Patents (OSTI)

A bearing system includes backup bearings for supporting a rotating shaft upon failure of primary bearings. In the preferred embodiment, the backup bearings are rolling element bearings having their rolling elements disposed out of contact with their associated respective inner races during normal functioning of the primary bearings. Displacement detection sensors are provided for detecting displacement of the shaft upon failure of the primary bearings. Upon detection of the failure of the primary bearings, the rolling elements and inner races of the backup bearings are brought into mutual contact by axial displacement of the shaft.

Kapich, Davorin D. (Carlsbad, CA)

1987-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Advanced Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Glazing Systems Glazing Systems Using Non-Structural Center Glazing Layers Windows in the United States use aproximately 2 quads a year in heating energy, approximately one third of all building space heating energy used and the largest single end use attributed to windows. Even if all existing windows were replaced with todayÂ’s ENERGY STAR low-e products (U values < 0.35 Btu/hr-ft2-F), windows related heating would still be over 1 Quad. Because heating loads are strongly tied to conductive losses, technologies which lead to lower window U-factors are the key to reducing heating energy. A 0.1 Btu/hr-ft2-F window is targeted as a product, which will meet the requirements of zero-energy homes. Dynamic control of solar gains will further reduce heating needs by allowing winter solar heat gains to be effectively utilized while limiting cooling season gains. Significant cooling load savings can also be expected from lower U-factor windows in certain climates and from dynamic windows in all climates.

402

Ignition system  

SciTech Connect

This patent describes an ignition system of an internal combustion engine which consists of: a permanent magnet supported by a rotary member of the engine adapted to rotate in synchronism with a rotary shaft of the engine; a generating coil for generating an electromotive force to produce an electric current as the permanent magnet acts on the generating coil during the rotation of the rotary member; an ignition capacitor charged by the electric current generated by the generating coil; a thyristor caused to turn on by a counter electromotive force generated by the generating coil to thereby cause the ignition capacitor to begin to discharge; and an ignition coil generating a high voltage as the ignition capacitor begins to discharge, to cause a spark discharge to take place in an ignition plug of the internal combustion engine.

Kondo, T.; Ohno, S.

1986-09-16T23:59:59.000Z

403

Computer Systems Administrator  

E-Print Network (OSTI)

Computer Systems Administrator Fort Collins, CO POSITION A Computer Systems Administrator (Non activities. RESPONSIBILITIES The System Administrator will provide Unix/Linux, Windows computer system or computer science, and three years computer systems administration experience. DURATION The work is planned

404

Solar system  

SciTech Connect

An improved solar heat collecting system is described comprising: a collecting means having upper and lower end caps; means for supporting the collecting means in a position generally perpendicular to ambit solar radiation and to permit periodic adjustment thereof; the support means including a base, a first support bar pivotally secured to the base and extending parallel to the ground, and a first support member extending perpendicular from the first support bar to the lower end cap. The support means also includes a second support bar pivotally secured to the base and extending generally parallel to the first support bar, a support leg having a lower portion that extends perpendicularly from the second support bar, an intermediate leg portion slidingly mounted on the lower leg portion and an upper leg portion pivotally secured to the intermediate leg portion, and a second support member extending perpendicularly from the upper leg portion to the upper end cap; lens means disposed above the collecting means for concentrating solar radiation on the collecting means; a pair of reflector means mounted below and on opposite sides of the radiation shadow of the lens means for concentrating solar radiation on the collecting means; mounting means for mounting the lens means and the reflector means. The mounting means includes first and second bracket means rotatively mounted respectively to the first and second support members. A pair of radially extending U-shaped reflector mounts have opposite ends secured to respective bracket means, and a pair of radially extending lens supports secured to respective bracket means; and means for rotating the mounting means and associated lens mean and reflector means to track the source of solar radiation whereby an improved, highly efficient solar heat collecting system is provided.

Gregory, S.T.

1987-02-24T23:59:59.000Z

405

Report for slot cutter proof-of-principle test, Buried Waste Containment System project. Revision 1  

SciTech Connect

Several million cubic feet of hazardous and radioactive waste was buried in shallow pits and trenches within many US Department of Energy (US DOE) sites. The pits and trenches were constructed similarly to municipal landfills with both stacked and random dump waste forms such as barrels and boxes. Many of the hazardous materials in these waste sites are migrating into groundwater systems through plumes and leaching. On-site containment is one of the options being considered for prevention of waste migration. This report describes the results of a proof-of-principle test conducted to demonstrate technology for containing waste. This proof-of-principle test, conducted at the RAHCO International, Inc., facility in the summer of 1997, evaluated equipment techniques for cutting a horizontal slot beneath an existing waste site. The slot would theoretically be used by complementary equipment designed to place a cement barrier under the waste. The technology evaluated consisted of a slot cutting mechanism, muck handling system, thrust system, and instrumentation. Data were gathered and analyzed to evaluate the performance parameters.

NONE

1998-05-21T23:59:59.000Z

406

Onsite Wastewater Treatment Systems: Spray Distribution System  

E-Print Network (OSTI)

Spray distribution systems for wastewater are much like lawn sprinkler systems, in that they spray treated wastewater over the surface of a yard. This publication explains how spray distribution systems work, what their design requirements are...

Lesikar, Bruce J.

2008-10-23T23:59:59.000Z

407

Separation system  

DOE Patents (OSTI)

A separation system for dewatering radioactive waste materials includes a disposal container, drive structure for receiving the container, and means for releasably attaching the container to the drive structure. Separation structure disposed in the container adjacent the inner surface of the side wall structure retains solids while allowing passage of liquids. Inlet port structure in the container top wall is normally closed by first valve structure that is centrifugally actuated to open the inlet port and discharge port structure at the container periphery receives liquid that passes through the separation structure and is normally closed by second valve structure that is centrifugally actuated to open the discharge ports. The container also includes coupling structure for releasable engagement with the centrifugal drive structure. Centrifugal force produced when the container is driven in rotation by the drive structure opens the valve structures, and radioactive waste material introduced into the container through the open inlet port is dewatered, and the waste is compacted. The ports are automatically closed by the valves when the container drum is not subjected to centrifugal force such that containment effectiveness is enhanced and exposure of personnel to radioactive materials is minimized.

Rubin, Leslie S. (Newton, MA)

1986-01-01T23:59:59.000Z

408

A MATLAB-based eye tracking control system using non-invasive helmet head restraint in the macaque  

Science Journals Connector (OSTI)

AbstractBackground Tracking eye position is vital for behavioral and neurophysiological investigations in systems and cognitive neuroscience. Infrared camera systems which are now available can be used for eye tracking without the need to surgically implant magnetic search coils. These systems are generally employed using rigid head fixation in monkeys, which maintains the eye in a constant position and facilitates eye tracking. New method We investigate the use of non-rigid head fixation using a helmet that constrains only general head orientation and allows some freedom of movement. We present a MATLAB software solution to gather and process eye position data, present visual stimuli, interact with various devices, provide experimenter feedback and store data for offline analysis. Comparison with existing method Our software solution achieves excellent timing performance due to the use of data streaming, instead of the traditionally employed data storage mode for processing analog eye position data. Results We present behavioral data from two monkeys, demonstrating that adequate performance levels can be achieved on a simple fixation paradigm and show how performance depends on parameters such as fixation window size. Our findings suggest that non-rigid head restraint can be employed for behavioral training and testing on a variety of gaze-dependent visual paradigms, reducing the need for rigid head restraint systems for some applications. Conclusion While developed for macaque monkey, our system of course can work equally well for applications in human eye tracking where head constraint is undesirable.

Paolo De Luna; Mohamed Faiz Bin Mohamed Mustafar; Gregor Rainer

2014-01-01T23:59:59.000Z

409

Smaller Footprint Drilling System for Deep and Hard Rock Environments; Feasibility of Ultra-High-Speed Diamond Drilling  

SciTech Connect

The two phase program addresses long-term developments in deep well and hard rock drilling. TerraTek believes that significant improvements in drilling deep hard rock will be obtained by applying ultra-high rotational speeds (greater than 10,000 rpm). The work includes a feasibility of concept research effort aimed at development that will ultimately result in the ability to reliably drill ''faster and deeper'' possibly with smaller, more mobile rigs. The principle focus is on demonstration testing of diamond bits rotating at speeds in excess of 10,000 rpm to achieve high rate of penetration (ROP) rock cutting with substantially lower inputs of energy and loads. The significance of the ultra-high rotary speed drilling system is the ability to drill into rock at very low weights on bit and possibly lower energy levels. The drilling and coring industry today does not practice this technology. The highest rotary speed systems in oil field and mining drilling and coring today run less than 10,000 rpm--usually well below 5,000 rpm. This document details the progress to date on the program entitled ''Smaller Footprint Drilling System for Deep and Hard Rock Environments: Feasibility of Ultra-High-Speed Diamond Drilling'' for the period starting 1 October 2004 through 30 September 2005. Additionally, research activity from 1 October 2005 through 28 February 2006 is included in this report: (1) TerraTek reviewed applicable literature and documentation and convened a project kick-off meeting with Industry Advisors in attendance. (2) TerraTek designed and planned Phase I bench scale experiments. Some difficulties continue in obtaining ultra-high speed motors. Improvements have been made to the loading mechanism and the rotational speed monitoring instrumentation. New drill bit designs have been provided to vendors for production. A more consistent product is required to minimize the differences in bit performance. A test matrix for the final core bit testing program has been completed. (3) TerraTek is progressing through Task 3 ''Small-scale cutting performance tests''. (4) Significant testing has been performed on nine different rocks. (5) Bit balling has been observed on some rock and seems to be more pronounces at higher rotational speeds. (6) Preliminary analysis of data has been completed and indicates that decreased specific energy is required as the rotational speed increases (Task 4). This data analysis has been used to direct the efforts of the final testing for Phase I (Task 5). (7) Technology transfer (Task 6) has begun with technical presentations to the industry (see Judzis).

Arnis Judzis; Alan Black; Homer Robertson

2006-03-01T23:59:59.000Z

410

Integrated Nanofluidic Systems for Systems Biotechnology  

E-Print Network (OSTI)

Integrated Nanofluidic Systems for Systems Biotechnology Wednesday October 28 2009 Burchard 118, 11 in prestigious journals including Science and Nature Biotechnology. Hong's research interests include Bio

Fisher, Frank

411

NREL: Energy Systems Integration Facility - Systems Integration  

NLE Websites -- All DOE Office Websites (Extended Search)

system components for grid-connected, standalone, and microgrid applications Test large power system components such as inverters, diesel and natural gas generators, battery...

412

Advanced coal-fueled industrial cogeneration gas turbine system  

SciTech Connect

This report covers the activity during the period from 2 June 1991 to 1 June 1992. The major areas of work include: the combustor sub-scale and full size testing, cleanup, coal fuel specification and processing, the Hot End Simulation rig and design of the engine parts required for use with the coal-fueled combustor island. To date Solar has demonstrated: Stable and efficient combustion burning coal-water mixtures using the Two Stage Slagging Combustor; Molten slag removal of over 97% using the slagging primary and the particulate removal impact separator; and on-site preparation of CWM is feasible. During the past year the following tasks were completed: The feasibility of on-site CWM preparation was demonstrated on the subscale TSSC. A water-cooled impactor was evaluated on the subscale TSSC; three tests were completed on the full size TSSC, the last one incorporating the PRIS; a total of 27 hours of operation on CWM at design temperature were accumulated using candle filters supplied by Refraction through Industrial Pump Filter; a target fuel specification was established and a fuel cost model developed which can identify sensitivities of specification parameters; analyses of the effects of slag on refractory materials were conducted; and modifications continued on the Hot End Simulation Rig to allow extended test times.

LeCren, R.T.; Cowell, L.H.; Galica, M.A.; Stephenson, M.D.; When, C.S.

1992-06-01T23:59:59.000Z

413

Minimal fusion systems.  

E-Print Network (OSTI)

??We define minimal fusion systems in a way that every non-solvable fusion system has a section which is minimal. Minimal fusion systems can also be… (more)

Henke, Ellen

2010-01-01T23:59:59.000Z

414

Object Management Systems  

E-Print Network (OSTI)

Object-Oriented Database Management Systems for EngineeringR. Cassel. Distribution Management Systems: Functions and8-PWR 1988. Network Management Systems 52 Subodh Bapat.

Gollu, Aleks Ohannes

1995-01-01T23:59:59.000Z

415

Environmental Management System  

NLE Websites -- All DOE Office Websites (Extended Search)

Management System Environmental Management System An Environmental Management System is a systematic method for assessing mission activities, determining the environmental impacts...

416

Environmental Management System Plan  

E-Print Network (OSTI)

R-3 • Environmental Management System Plan References 30.of Energy, Safety Management System Policy, DOE P 450.4 (E), Environmental Management Systems ? Requirements with

Fox, Robert

2009-01-01T23:59:59.000Z

417

Earth System Modeling  

Science Journals Connector (OSTI)

Earth system models are important research tools for improving understanding ... climate system (and maybe never will), Earth system models nowadays typically focus on specific aspects, for...

Patrick Jöckel

2012-01-01T23:59:59.000Z

418

Geographic Information System (GIS)  

Science Journals Connector (OSTI)

The geographic information system is a branch of health information system and public health information system ...developed for the capture, storage, manipulation, analysis, and visualization of geographic ...

2008-01-01T23:59:59.000Z

419

Logical Systems Incorporated The Help Systems  

E-Print Network (OSTI)

Logical Systems Incorporated The Help Systems T A B L E O F C O N T E N T S Introduction ..................................... page 2 HELP/CMD ..................................... page 3 HELPRESx ................................... page 17 #12;LDOS Help System Page 1 The LDOS HELP Systems Introduction This documentation covers all

Mann, Tim

420

System design description cone penetrometer system  

SciTech Connect

The system design description documents in detail the design of the cone penetrometer system. The systems includes the cone penetrometer physical package, raman spectroscopy package and moisture sensor package. Information pertinent to the system design, development, fabrication and testing is provided.

Seda, R.Y., Westinghouse Hanford

1996-08-12T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Industrial and Systems engineering  

E-Print Network (OSTI)

Industrial and Systems engineering COLLEGE of ENGINEERING DepartmentofIndustrialandSystemsEngineering EDGE Engineering Entrepreneur Certificate Program is a great addition to an industrial and systems to expert clinical recommendations. engineering.wayne.edu/isefaculty Industrial and systems engineering

Berdichevsky, Victor

422

Systems and Industry Analyses  

NLE Websites -- All DOE Office Websites (Extended Search)

Gasifipedia Gasifier Optimization Feed Systems Syngas Processing Systems Analyses Gasification Plant Databases International Activity Program Plan Project Portfolio Project...

423

Gasification Systems Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

Gasifipedia Gasifier Optimization Feed Systems Syngas Processing Systems Analyses Gasification Plant Databases International Activity Program Plan Project Portfolio Project...

424

Gasification Systems Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

Publications News Gasifipedia Gasifier Optimization Feed Systems Syngas Processing Systems Analyses Gasification Plant Databases International Activity Program Plan Project...

425

Hospital Information System  

Science Journals Connector (OSTI)

A hospital information system is an information system for processing data, information and knowledge in hospital ...

2008-01-01T23:59:59.000Z

426

Hydride-dehydride module within ARIES (Advanced Recovery and Integrated Extraction System)  

SciTech Connect

One of the many requirements placed on the DOE is the reduction of the nuclear stockpile through dismantlement programs. The DOE Office of Fissile Materials Disposition (OFMD) has been tasked with the disposition of excess plutonium and other fissile materials. On the list of items containing excess fissile materials are nuclear weapon cores, pits. The Advanced Recovery and integrated Extraction System (ARIES) at Los Alamos National Laboratory is the pit disassembly and conversion demonstration line that is being used to gather data to support the design of the full scale pit disassembly and conversion facility. The Hydride Dehydride recycle system is an important element to this program, because it provides these dismantlement programs with a technology for removing plutonium from nuclear weapons without producing large amounts of waste compared to historical processes used in the DOE complex. The Hydride Dehydride recycle process can separate plutonium from other weapons components resulting in an unclassified plutonium metal button. After separation, this button can be stored in long term storage containers or processed to produce plutonium oxide, which will be used by either of the plutonium disposition options, mixed oxide fuel burning in a nuclear reactor or immobilization. Once placed into long term storage containers, either the plutonium metal or plutonium oxide can be inspected by bilateral or international agencies to invoke transparency of the plutonium.

Flamm, B.F.; Isom, G.M.; Nelson, T.O.

1998-12-31T23:59:59.000Z

427

The application of Plant Reliability Data Information System (PRINS) to CANDU reactor  

SciTech Connect

As risk-informed applications (RIAs) are actively implanted in the nuclear industry, an issue associated with technical adequacy of Probabilistic Safety Assessment (PSA) arises in its modeling and data sourcing. In Korea, PSA for all Korean NPPs has been completed and KHNP(Korea Hydro and Nuclear Power Plant Company) developed the database called the Plant Reliability Data Information System (PRinS). It has several characteristics that distinguish it from other database system such as NPRDs (INPO,1994), PRIS (IAEA), and SRDF (EdF). This database has the function of systematic data management such as automatic data-gathering, periodic data deposition and updating, statistical analysis including Bayesian method, and trend analysis of failure rate or unavailability. In recent PSA for CANDU reactor, the component failure data of EPRI ALWR URD and Component Reliability Database were preferentially used as generic data set. The error factor for most component failure data was estimated by using the information NUREG/CR-4550 and NUREG/CR-4639. Also, annual trend analysis was performed for the functional losses of components using the statistical analysis and chart module of PRinS. Furthermore, the database has been updated regularly and maintained as a living program to reflect the current status. This paper presents the failure data analysis using PRinS which provides Bayesian analysis on main components in the CANDU reactor. (authors)

Hwang, S. W.; Lim, Y. H.; Park, H. C. [Korea Hydro and Nuclear Power Co., Ltd., Naah-ri 260, Yangnam-myun, Gyeongju-si, Gyeong Buk (Korea, Republic of)

2012-07-01T23:59:59.000Z

428

Detection of Volatile Organics Using a Surface Acoustic Wave Array System  

SciTech Connect

A chemical sensing system based on arrays of surface acoustic wave (SAW) delay lines has been developed for identification and quantification of volatile organic compounds (VOCs). The individual SAW chemical sensors consist of interdigital transducers patterned on the surface of an ST-cut quartz substrate to launch and detect the acoustic waves and a thin film coating in the SAW propagation path to perturb the acoustic wave velocity and attenuation during analyte sorption. A diverse set of material coatings gives the sensor arrays a degree of chemical sensitivity and selectivity. Materials examined for sensor application include the alkanethiol-based self-assembled monolayer, plasma-processed films, custom-synthesized conventional polymers, dendrimeric polymers, molecular recognition materials, electroplated metal thin films, and porous metal oxides. All of these materials target a specific chemical fi.mctionality and the enhancement of accessible film surface area. Since no one coating provides absolute analyte specificity, the array responses are further analyzed using a visual-empirical region-of-influence (VERI) pattern recognition algorithm. The chemical sensing system consists of a seven-element SAW array with accompanying drive and control electronics, sensor signal acquisition electronics, environmental vapor sampling hardware, and a notebook computer. Based on data gathered for individual sensor responses, greater than 93%-accurate identification can be achieved for any single analyte from a group of 17 VOCs and water.

ANDERSON, LAWRENCE F.; BARTHOLOMEW, JOHN W.; CERNOSEK, RICHARD W.; COLBURN, CHRISTOPHER W.; CROOKS, R.M.; MARTINEZ, R.F.; OSBOURN, GORDON C.; RICCO, A.J.; STATON, ALAN W.; YELTON, WILLIAM G.

1999-10-14T23:59:59.000Z

429

Harmonic measurements made on the upgraded New Zealand inter-island HVdc transmission system  

SciTech Connect

This paper introduces the recent upgrade to the New Zealand inter-island HVdc transmission system. It then details the procedure of one of several tests conducted to measure harmonic levels created by the upgraded transmission system. Harmonic levels were measured using the CHART (Continuous Harmonic Analysis in Real-Time) harmonic monitoring instrumentation. The connection of CHART to the high voltage network and its configuration during the test is discussed. A sample of results gathered while monitoring are presented, including characteristic harmonics of the converter, and maximum voltage and current levels up to the 50th harmonic for each of the three a.c. phases. During the tests one of the two a.c. harmonic filters was switched out to observe its effect on harmonic levels. It was found that with both a.c. harmonic filters operating, most harmonic levels were lower than with only one filter operating. However some harmonic levels, namely the 4th harmonic, were larger with both filters operating. The paper is concluded with a discussion of the results and of the difficulties encountered in measuring harmonics of very low level.

Miller, A.J.V.; Dewe, M.B. (Univ. of Canterbury, Christchurch (New Zealand))

1994-07-01T23:59:59.000Z

430

PIA - Human Resources System/Payroll System | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

System PIA - Human Resources SystemPayroll System More Documents & Publications PIA - INL PeopleSoft - Human Resource System PIA - INL SECURITY INFORMATION MANAGEMENT SYSTEM...

431

Influence strategies for systems of systems  

E-Print Network (OSTI)

Distributed decision making has been identified as a source of managerial complexity for leaders of systems of systems (SoS). A new framework, AIR (Anticipation-Influence-Reaction), is proposed to capture the feedback ...

Shah, Nirav Bharat, 1979-

2013-01-01T23:59:59.000Z

432

Heating System Specification Specification of Heating System  

E-Print Network (OSTI)

Appendix A Heating System Specification /* Specification of Heating System (loosely based */ requestHeat : Room ­? bool; 306 #12; APPENDIX A. HEATING SYSTEM SPECIFICATION 307 /* user inputs */ livingPattern : Room ­? behaviour; setTemp : Room ­? num; heatSwitchOn, heatSwitchOff, userReset : simple

Day, Nancy

433

Energy Systems Integration  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Systems Integration Systems Integration Ben Kroposki, PhD, PE Director, Energy Systems Integration National Renewable Energy Laboratory 2 Reducing investment risk and optimizing systems in a rapidly changing energy world * Increasing penetration of variable RE in grid * Increasing ultra high energy efficiency buildings and controllable loads * New data, information, communications and controls * Electrification of transportation and alternative fuels * Integrating energy storage (stationary and mobile) and thermal storage * Interactions between electricity/thermal/fuels/data pathways * Increasing system flexibility and intelligence Current Energy Systems Future Energy Systems Why Energy Systems Integration? 3 Energy Systems Integration Continuum Scale Appliance (Plug)

434

Systems Analysis Workshop Purpose  

NLE Websites -- All DOE Office Websites (Extended Search)

National Renewable Energy Laboratory National Renewable Energy Laboratory DOE Hydrogen Program DOE Hydrogen Program Systems Analysis Workshop Systems Analysis Workshop Systems Integration Production Delivery Conversion Application Education Codes & Standards Safety Tech Validation Storage Systems Integration Production Delivery Conversion Application Education Codes & Standards Safety Tech Validation Storage Washington D.C. 28-29 Jul 04 Dale Gardner Systems Integration Operated for the U.S. Department of Energy by Midwest Research Institute * Battelle 2 Systems Analysis Workshop Topics * Meeting Goals * Systems Integration * Roles/Responsibilities of Analysis Participants * Systems Analysis * From this Workshop * Capability Presentations 3 Systems Analysis Workshop Meeting Goals 1) Understand the roles and activities of the DOE Technology Analyst,

435

Rural Intelligent Transportation Systems  

E-Print Network (OSTI)

System--activates lights on a STOP sign as a vehicle approaches the sign. · Curve Warning System System--records data on vehicle behavior that can be analyzed and used as a design input. Design the systems. Each system is made up of detection nodes that trigger the sign nodes. Results Foderberg

Minnesota, University of

436

Fan System Assessment Tool  

Energy.gov (U.S. Department of Energy (DOE))

The Fan System Assessment Tool (FSAT) is a free online software tool that helps industrial users quantify energy use and savings opportunities in industrial fan systems. Use FSAT to understand how well your fan systems are operating, determine the economic benefit of system modifications, and establish which options are most economically viable when multiple opportunities exist for system modification.

437

Advanced Materials for Mercury 50 Gas Turbine Combustion System  

SciTech Connect

Solar Turbines Incorporated (Solar), under cooperative agreement number DE-FC26-0CH11049, has conducted development activities to improve the durability of the Mercury 50 combustion system to 30,000 hours life and reduced life cycle costs. This project is part of Advanced Materials in the Advanced Industrial Gas Turbines program in DOE's Office of Distributed Energy. The targeted development engine was the Mercury{trademark} 50 gas turbine, which was developed by Solar under the DOE Advanced Turbine Systems program (DOE contract number DE-FC21-95MC31173). As a generator set, the Mercury 50 is used for distributed power and combined heat and power generation and is designed to achieve 38.5% electrical efficiency, reduced cost of electricity, and single digit emissions. The original program goal was 20,000 hours life, however, this goal was increased to be consistent with Solar's standard 30,000 hour time before overhaul for production engines. Through changes to the combustor design to incorporate effusion cooling in the Generation 3 Mercury 50 engine, which resulted in a drop in the combustor wall temperature, the current standard thermal barrier coated liner was predicted to have 18,000 hours life. With the addition of the advanced materials technology being evaluated under this program, the combustor life is predicted to be over 30,000 hours. The ultimate goal of the program was to demonstrate a fully integrated Mercury 50 combustion system, modified with advanced materials technologies, at a host site for a minimum of 4,000 hours. Solar was the Prime Contractor on the program team, which includes participation of other gas turbine manufacturers, various advanced material and coating suppliers, nationally recognized test laboratories, and multiple industrial end-user field demonstration sites. The program focused on a dual path development route to define an optimum mix of technologies for the Mercury 50 and future gas turbine products. For liner and injector development, multiple concepts including high thermal resistance thermal barrier coatings (TBC), oxide dispersion strengthened (ODS) alloys, continuous fiber ceramic composites (CFCC), and monolithic ceramics were evaluated before down-selection to the most promising candidate materials for field evaluation. Preliminary, component and sub-scale testing was conducted to determine material properties and demonstrate proof-of-concept. Full-scale rig and engine testing was used to validated engine performance prior to field evaluation at a Qualcomm Inc. cogeneration site located in San Diego, California. To ensure that the CFCC liners with the EBC proposed under this program would meet the target life, field evaluations of ceramic matrix composite liners in Centaur{reg_sign} 50 gas turbine engines, which had previously been conducted under the DOE sponsored Ceramic Stationary Gas Turbine program (DE-AC02-92CE40960), was continued under this program at commercial end-user sites under Program Subtask 1A - Extended CFCC Materials Durability Testing. The goal of these field demonstrations was to demonstrate significant component life, with milestones of 20,000 and 30,000 hours. Solar personnel monitor the condition of the liners at the field demonstration sites through periodic borescope inspections and emissions measurements. This program was highly successful at evaluating advanced materials and down-selecting promising solutions for use in gas turbine combustions systems. The addition of the advanced materials technology has enabled the predicted life of the Mercury 50 combustion system to reach 30,000 hours, which is Solar's typical time before overhaul for production engines. In particular, a 40 mil thick advanced Thermal Barrier Coating (TBC) system was selected over various other TBC systems, ODS liners and CFCC liners for the 4,000-hour field evaluation under the program. This advanced TBC is now production bill-of-material at various thicknesses up to 40 mils for all of Solar's advanced backside-cooled combustor liners (Centaur 50, Taurus 60, Mars 100, Taurus 70,

Price, Jeffrey

2008-09-30T23:59:59.000Z

438

Fundamentals of Dynamical Systems  

Science Journals Connector (OSTI)

For the purposes of control system design, analysis, test, and repair, the most important part of the very broad subject known as system theory is the theory of dynamical systems. It is difficult to give a pre...

William S. Levine

2005-01-01T23:59:59.000Z

439

Analyzing Scrip Systems  

E-Print Network (OSTI)

Scrip systems provide a nonmonetary trade economy for exchange of resources. We model a scrip system as a stochastic game and study system design issues on selection rules to match potential trade partners over time. We ...

Johnson, Kristine Dianne

440

Hopper System Diagram  

NLE Websites -- All DOE Office Websites (Extended Search)

System Diagram System Diagram Diagram of IO architecture on Hopper Diagram of external IO services on the Hopper system Last edited: 2011-04-14 15:11:1...

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Development of Operation System  

Science Journals Connector (OSTI)

We are gradually developing a total hospital information system known as GUNMAS (Gunma University Network for Medical-Hospital- Information Archiving System). an operation system is also being developed as part o...

Seiji Kato M.D.; Yasuharu Kitani M.D.…

1992-01-01T23:59:59.000Z

442

Steam System Survey Guide  

Energy.gov (U.S. Department of Energy (DOE))

This guide provides technical information for steam system operational personnel and plant energy managers on some of the major opportunities available to improve the energy efficiency and productivity of industrial steam systems. The guide covers five main areas of investigation: (1) profiling a steam system, (2) identifying steam properties for the steam system, (3) improving boiler operations, (4) improving resource utilization in the steam system, and (5) investigating energy losses in the steam distribution system.

443

Natural Gas Discovery and Development Impacts on Rio Vista and Its Community  

E-Print Network (OSTI)

Modern Rotary Drilling Rig………………………………………………………………………………….Equipment Used on Modern Rotary Drilling Rig 142 Figure A2.Used on Modern Rotary Drilling Rig Source: California

Gbedema, Tometi Koku

2006-01-01T23:59:59.000Z

444

CONTRACTOR PURCHASING SYSTEM REVIEWS  

Energy Savers (EERE)

PURCHASING SYSTEM REVIEWS RISK ASSESSMENT MATRIX RISK CATEGORY PERFORMANCE SCHEDULE COST HIGH (3) --Performance data casts significant doubt on the ability of the system or key...

445

Abstract: Regularized Boussinesq systems  

E-Print Network (OSTI)

A Boussinesq System for Two-way Propagation of Nonlinear Dispersive Waves. In this report, we study a system which describes approximately the ...

446

Control system design method  

DOE Patents (OSTI)

A control system design method and concomitant control system comprising representing a physical apparatus to be controlled as a Hamiltonian system, determining elements of the Hamiltonian system representation which are power generators, power dissipators, and power storage devices, analyzing stability and performance of the Hamiltonian system based on the results of the determining step and determining necessary and sufficient conditions for stability of the Hamiltonian system, creating a stable control system based on the results of the analyzing step, and employing the resulting control system to control the physical apparatus.

Wilson, David G. (Tijeras, NM); Robinett, III, Rush D. (Tijeras, NM)

2012-02-21T23:59:59.000Z

447

Flex Fuel Vehicle Systems  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

& Variable Advanced Management Injection Injection Sensors Control Units Fuel Supply & Plastic Parts Control Transmission Engineering Gasoline Systems GSENS, GSENS-NA System...

448

Umbra's system representation.  

SciTech Connect

This document describes the Umbra System representation. Umbra System representation, initially developed in the spring of 2003, is implemented in Incr/Tcl using concepts borrowed from Carnegie Mellon University's Architecture Description Language (ADL) called Acme. In the spring of 2004 through January 2005, System was converted to Umbra 4, extended slightly, and adopted as the underlying software system for a variety of Umbra applications that support Complex Systems Engineering (CSE) and Complex Adaptive Systems Engineering (CASE). System is now a standard part Of Umbra 4. While Umbra 4 also includes an XML parser for System, the XML parser and Schema are not described in this document.

McDonald, Michael James

2005-07-01T23:59:59.000Z

449

Precision Diagnostic System  

NLE Websites -- All DOE Office Websites (Extended Search)

Precision Diagnostic System For NIF to reach the goal of ignition, it needs to produce highly shaped pulses that are precisely controlled. NIF's precision diagnostic system (PDS)...

450

Information retrieval system: impacts of water-level changes on uses of federal storage reservoirs of the Columbia River.  

SciTech Connect

A project undertaken to provide the Bonneville Power Administration (BPA) with information needed to conduct environmental assessments and meet requirements of the National Environmental Policy Act (NEPA) and the Pacific Northwest Electric Power Planning and Conservation Act (Regional Act) is described. Access to information on environmental effects would help BPA fulfill its responsibilities to coordinate power generation on the Columbia River system, protect uses of the river system (e.g., irrigation, recreation, navigation), and enhance fish and wildlife production. Staff members at BPA identified the need to compile and index information resources that would help answer environmental impact questions. A computer retrieval system that would provide ready access to the information was envisioned. This project was supported by BPA to provide an initial step toward a compilation of environmental impact information. Scientists at Pacific Northwest Laboratory (PNL) identified, gathered, and evaluated information related to environmental effects of water level on uses of five study reservoirs and developed and implemented and environmental data retrieval system, which provides for automated storage and retrieval of annotated citations to published and unpublished information. The data retrieval system is operating on BPA's computer facility and includes the reservoir water-level environmental data. This project was divided into several tasks, some of which were conducted simultaneously to meet project deadlines. The tasks were to identify uses of the five study reservoirs, compile and evaluate reservoir information, develop a data entry and retrieval system, identify and analyze research needs, and document the data retrieval system and train users. Additional details of the project are described in several appendixes.

Fickeisen, D.H.; Cowley, P.J.; Neitzel, D.A.; Simmons, M.A.

1982-09-01T23:59:59.000Z

451

NERSC File Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Systems Systems NERSC File Systems Overview NERSC file systems can be divided into two categories: local and global. Local file systems are only accessible on a single platform, providing best performance; global file systems are accessible on multiple platforms, simplifying data sharing between platforms. File systems are configured for different purposes. On each machine you have access to at least three different file system Home: Permanent, relatively small storage for data like source code, shell scripts, etc. that you want to keep. This file system is not tuned for high performance from parallel jobs. Referenced by the environment variable $HOME. Scratch: Large, high-performance file system. Place your large data files in this file system for capacity and capability computing. Data is

452

EpidemicSim: Epidemic Simulation System with Realistic Mobility  

E-Print Network (OSTI)

human behavior and social interactions for epidemic and pandemic predictions. Nearly all of these models 32816 Email: {skopman,miakbas,turgut}@eecs.ucf.edu Abstract--Much attention has been paid to modeling and predictive simulations rely on synthetic individuals to simulate social patterns using data gathered from

Turgut, Damla

453

Utility-scale Power Tower Solar Systems: Performance Acceptance Test Guidelines  

Science Journals Connector (OSTI)

Abstract Prior to commercial operation, large solar systems in utility-size power plants need to pass performance acceptance tests conducted by the engineering, procurement, and construction (EPC) contractor or owners. In lieu of the present absence of ASME or other international test codes developed for this purpose, the NREL undertook the development of interim Guidelines to provide recommendations for test procedures that can yield results of a high level of accuracy consistent with good engineering knowledge and practice. The Guidelines contained here follow the general approach of the earlier NREL report on parabolic trough collector fields, but in this case are specifically written for power tower solar systems composed of a heliostat (reflector) field directing the sun's rays to a receiver (heat exchanger) on a high central tower. The working fluid in the tower receiver can be molten salt, water/steam, air, CO2, or other suitable fluids, each with its own particular attributes. The fundamental differences between acceptance of a solar power plant and a conventional fossil-fired plant are the inherently transient nature of the energy source and the necessity to use a performance projection model in the acceptance process. Two primary types of test runs are to be conducted. The first – the Short-Duration Steady-State Thermal Power Test (Power Test) – measures the thermal power output of the solar system under clear-sky conditions over a short period, during which thermal equilibrium and stable steady-state conditions exist, and compares the measured results to performance model projections for those conditions. The second test type – the Long-Duration Production (or Reliability) Test (Production Test)– is a continuous multi-day energy test that gathers multiple detailed daily thermal energy outputs and compares the results to projections from a performance model. Both clear-sky and partly cloudy conditions are acceptable. Additionally, the functionality of the solar system should be observed with regard to such items as daily startup, normal operation, standby and shutdown.

D. Kearney

2014-01-01T23:59:59.000Z

454

Chemical Looping Combustion Reactions and Systems  

SciTech Connect

Chemical Looping Combustion (CLC) is one promising fuel-combustion technology, which can facilitate economic CO{sub 2} capture in coal-fired power plants. It employs the oxidation/reduction characteristics of a metal, or oxygen carrier, and its oxide, the oxidizing gas (typically air) and the fuel source may be kept separate. This topical report discusses the results of four complementary efforts: (5.1) the development of process and economic models to optimize important design considerations, such as oxygen carrier circulation rate, temperature, residence time; (5.2) the development of high-performance simulation capabilities for fluidized beds and the collection, parameter identification, and preliminary verification/uncertainty quantification; (5.3) the exploration of operating characteristics in the laboratoryscale bubbling bed reactor, with a focus on the oxygen carrier performance, including reactivity, oxygen carrying capacity, attrition resistance, resistance to deactivation, cost and availability; and (5.4) the identification of kinetic data for copper-based oxygen carriers as well as the development and analysis of supported copper oxygen carrier material. Subtask 5.1 focused on the development of kinetic expressions for the Chemical Looping with Oxygen Uncoupling (CLOU) process and validating them with reported literature data. The kinetic expressions were incorporated into a process model for determination of reactor size and oxygen carrier circulation for the CLOU process using ASPEN PLUS. An ASPEN PLUS process model was also developed using literature data for the CLC process employing an iron-based oxygen carrier, and the results of the process model have been utilized to perform a relative economic comparison. In Subtask 5.2, the investigators studied the trade-off between modeling approaches and available simulations tools. They quantified uncertainty in the high-performance computing (HPC) simulation tools for CLC bed applications. Furthermore, they performed a sensitivity analysis for velocity, height and polydispersity and compared results against literature data for experimental studies of CLC beds with no reaction. Finally, they present an optimization space using simple non-reactive configurations. In Subtask 5.3, through a series of experimental studies, behavior of a variety of oxygen carriers with different loadings and manufacturing techniques was evaluated under both oxidizing and reducing conditions. The influences of temperature, degree of carrier conversion and thermodynamic driving force resulting from the difference between equilibrium and system O{sub 2} partial pressures were evaluated through several experimental campaigns, and generalized models accounting for these influences were developed to describe oxidation and oxygen release. Conversion of three solid fuels with widely ranging reactivities was studied in a small fluidized bed system, and all but the least reactive fuel (petcoke) were rapidly converted by oxygen liberated from the CLOU carrier. Attrition propensity of a variety of carriers was also studied, and the carriers produced by freeze granulation or impregnation of preformed substrates displayed the lowest rates of attrition. Subtask 5.4 focused on gathering kinetic data for a copper-based oxygen carrier to assist with modeling of a functioning chemical looping reactor. The kinetics team was also responsible for the development and analysis of supported copper oxygen carrier material.

Sarofim, Adel; Lighty, JoAnn; Smith, Philip; Whitty, Kevin; Eyring, Edward; Sahir, Asad; Alvarez, Milo; Hradisky, Michael; Clayton, Chris; Konya, Gabor; Baracki, Richard; Kelly, Kerry

2014-03-01T23:59:59.000Z

455

Fusion systems of -type  

Science Journals Connector (OSTI)

We prove results on 2-fusion systems related to the 2-fusion systems of groups of Lie type over the field of order 2 and certain sporadic groups. The results are used in a later paper to determine the N-systems: the 2-fusion systems of N-groups.

Michael Aschbacher

2013-01-01T23:59:59.000Z

456

SYSTEM DESIGN Lessons Learned  

E-Print Network (OSTI)

· 48% Efficiency PREREFORMER ZNO HDS TURBO EXPANDER FUEL CONDENSER FUEL EXHAUST H2 FUEL H2 A C FUEL Cell Systems High Power Shipboard System 625kW SSFC Demo 45-50% Efficient System Low Power High EfficiencyLow Power, High Efficiency Tactical Power System · Enable 3X improvement in Ship Service Fuel Cell

457

Space System Architecture  

E-Print Network (OSTI)

Final Report of SSPARC: the Space Systems, Policy, and Architecture Research Consortium (Thrust II and III)

McManus, Dr. Hugh

458

Medical imaging systems  

DOE Patents (OSTI)

A medical imaging system provides simultaneous rendering of visible light and diagnostic or functional images. The system may be portable, and may include adapters for connecting various light sources and cameras in open surgical environments or laparascopic or endoscopic environments. A user interface provides control over the functionality of the integrated imaging system. In one embodiment, the system provides a tool for surgical pathology.

Frangioni, John V

2013-06-25T23:59:59.000Z

459

Mission Operations & Data Systems  

E-Print Network (OSTI)

Mission Operations & Data Systems The LASP Mission Operations & Data Systems (MO&DS) group staffs and instruments. Operational software acts like the health systems in a body, ensuring that temperature, energy. The software monitors the health of on-board systems; anything unusual is flagged and sent to mission operators

Mojzsis, Stephen J.

460

From Jerry-Rigged to Petered Out: Lessons from the Deukmejian Era for Contemporary California State Budgeting  

E-Print Network (OSTI)

Seeks $700 Million Tax Rebate,” Sacramento Bee, May 20, Let Taxpayers Decide Rebate, Duke Says,” Sacramento Bee, cap formula led to tax rebates in 1987 – monies that might 

Mitchell, Daniel J.B.

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Design and Development of a Mid-Infrared Carbon Monoxide Sensor for a High-Pressure Combustor Rig  

E-Print Network (OSTI)

A sensor for carbon monoxide measurement has been developed using a mid-infrared quantum-cascade (QC) laser operating in the fundamental band (?v= 1) of CO near 4.5 ?m. The fundamental band was chosen due to its stronger absorption line...

Camou, Alejandro

2014-05-03T23:59:59.000Z

462

Evaluation and comparison of occupational noise exposure among workers on offshore and onshore oil well drilling rigs  

E-Print Network (OSTI)

Engineering Department, for the loan of equipment used for th is research. A special gratitude goes to Ing. Jav ier Mendieta, Safety Manager of Petroleos Mexicanos, for his help for the use of PEMEX facilities in my data collection. I would also like... to thank Ing. Ignacio Torres of PEMEX Safety Engineering Division for assisting in the data collection. DEDICATION This thesis is dedicated to my parents, Estela and Humberto, and also to my little sister Kary. CONTENTS I. INTRODUCTION The Problem...

Suarez Garcia, Humberto

1984-01-01T23:59:59.000Z

463

NETL: Methane Hydrates - DOE/NETL Projects  

NLE Websites -- All DOE Office Websites (Extended Search)

Characterizing Arctic Hydrates (Canadian Test Well and Alaskan "Wells of Opportunity") Characterizing Arctic Hydrates (Canadian Test Well and Alaskan "Wells of Opportunity") photo of drilling rig at Mallik 2L-38 location Rig at Mallik 2L-38 location courtesy Geological Survey of Canada DE-AT26-97FT34342 Goal The purpose of this project is to assess the recoverability and potential production characteristics of the onshore natural gas hydrate and associated free-gas accumulations in the Arctic of North America Performer United States Geological Survey, Denver, Colorado 80225 - partner in GSC-managed consortium and provide expertise in data gathering and analysis Background The U.S. Geological Survey has been participating in natural gas hydrate reservoir research with DOE NETL through an interagency agreement which began in the early 1980Â’s. The work has been an ongoing effort as part of

464

NREL: Systems Engineering - 2015 Wind Energy Systems Engineering...  

NLE Websites -- All DOE Office Websites (Extended Search)

Systems Engineering Wind Research Systems Engineering Printable Version 2015 Wind Energy Systems Engineering Workshop The third NREL Wind Energy Systems Engineering Workshop will...

465

Horizontal-axis wind-system rotor performance model comparison: a compendium  

SciTech Connect

This compendium consists of four reports, the purpose of which is to evaluate performance prediction methods for horizontal-axis wind turbines. The reports were prepared by four separate contractors. Oregon State University, AeroVironment, Inc., Aerospace Systems, Inc., and United Technologies Research Center (UTRC). Three of the four contractors used a blade-element/momentum analysis, while the fourth (UTRC) utilized a lifting line/prescribed wake analysis. These contractors were to apply their prediction methods to two rotors, that of the Enertech 1500 and that of the 1/3-scale UTRC 8 kW turbines. Results from the four prediction methods are compared with actual test data gathered via Controlled Velocity Testing (CVT), carried out by the Rocky Flats Wind Energy Research Center, operated by Rockwell International for the US Department of Energy. The conclusions of the four reports are reviewed in an introduction prepared by Rockwell International. For the Enertech 1500, rotor performance predictions closely agreed with CVT data. Yet, because of the lack of high tip speed ratio data, verification of the Glauert momentum theory was not possible. Predictions regarding the UTRC 1/3 scale 8 kW rotor did not agree well with test results. The reasons cited for the discrepancies center on inadequate airfoil section data and the varying blade pitch angles of the unique UTRC flexbeam rotor.

Not Available

1983-02-01T23:59:59.000Z

466

Mode Initialization for On-line Estimation of Power System Electromechanical Modes  

SciTech Connect

Measurement-based mode estimation methods are utilized to estimate electromechanical modes of a power system using phasor measurement units (PMU) data. These methods need to extract a certain amount of information before they can give useable mode estimation. Traditionally, the information is gathered solely from measurement data. Priori mode information from other resources (e.g. model eigenvalue analysis, engineering knowledge) are not fully utilized. For real time application, this means that mode estimation takes time to converge. By adding a mode regularization term in the objective function, this paper proposes a mode initialization method to include priori mode information in a regularized robust recursive least squares (R3LS) algorithm for on-line mode estimation. The proposed method is tested using a simple model, a 17 machine model and is shown to be able to shorten the convergence period of the R3LS algorithm. The proposed method is also applied on the measurement data recorded right before a major power outage in the western North American Grid on August 10th 1996 to show its potential applica-tion in detecting an approaching small signal stability problem.

Zhou, Ning; Trudnowski, Daniel; Pierre, John W.

2009-03-18T23:59:59.000Z

467

FNAL system patching design  

SciTech Connect

FNAL has over 5000 PCs running either Linux or Windows software. Protecting these systems efficiently against the latest vulnerabilities that arise has prompted FNAL to take a more central approach to patching systems. Due to different levels of existing support infrastructures, the patching solution for linux systems differs from that of windows systems. In either case, systems are checked for vulnerabilities by Computer Security using the Nessus tool.

Schmidt, Jack; Lilianstrom, Al; Romero, Andy; Dawson, Troy; Sieh, Connie; /Fermilab

2004-01-01T23:59:59.000Z

468

ELECTRICAL ENERGY SYSTEMS ELECTRICAL ENERGY SYSTEMS  

E-Print Network (OSTI)

. In its Energy Policy, the Scottish Government stated that it is Scotland's ambition to become a worldMEng ELECTRICAL ENERGY SYSTEMS #12;MEng ELECTRICAL ENERGY SYSTEMS Electrical energy is vital aspects of modern life. One of the biggest challenges facing society is the need for reliable energy

Strathclyde, University of

469

EPICS system: system structure and user interface  

SciTech Connect

This paper present the user's view of and the general organization of the EPICS control system at Fermilab. Various subsystems of the EPICS control system are discussed. These include the user command language, software protection, the device database, remote computer interfaces, and several application utilities. This paper is related to two other papers on EPICS: an overview paper and a detailed implementation paper.

West, R.E.; Bartlett, J.F.; Bobbitt, J.S.; Lahey, T.E.; Kramper, B.J.; MacKinnon, B.A.

1984-02-01T23:59:59.000Z

470

Renovating Residential HVAC Systems HVAC Systems  

E-Print Network (OSTI)

- 1 - LBNL 57406 Renovating Residential HVAC Systems HVAC Systems J.A. McWilliams and I.S. Walker and Air Conditioning), and Stacy Hunt and Ananda Harzell (IBACOS). #12;- 3 - Renovating Residential HVAC Guideline for Residential HVAC Retrofits (http

471

AUTONOMOUS ROBOTIC INSPECTION EXPERIMENTAL SYSTEM  

SciTech Connect

This document contains appendices on these topics: COMPUTERS AND CONTROLS; COMPUTER VISION SYSTEM; ELECTRICAL SYSTEMS; MECHANICAL SYSTEMS; ROBOTIC VEHICLE SYSTEMS; FIELD TRIALS.

David N. Rocheleau, Senior Investigator; Edward A. Hamilton, Associate Director, SCUREF; Jerry L. Hudgins, Senior Investigator; Paul McCarty, Graduate Research Assistant; Robert J. Schalkoff, Senior Investigator; Robert O. Pettus, Project Manager & Principal Investigator

1998-08-01T23:59:59.000Z

472

System Design | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

System Design System Design This template is used to define the system design System Design More Documents & Publications Transition Plan Training Plan Feasibility Study Report...

473

Environmental Management System  

NLE Websites -- All DOE Office Websites (Extended Search)

Management System Management System Environmental Management System An Environmental Management System is a systematic method for assessing mission activities, determining the environmental impacts of those activities, prioritizing improvements, and measuring results. May 30, 2012 The continuous improvement cycle Our Environmental Management System encourages continuous improvement of our environmental performance. Contact Environmental Communication & Public Involvement P.O. Box 1663 MS M996 Los Alamos, NM 87545 (505) 667-0216 Email Managing our effects on the environment We are committed to protecting the environment while conducting our national security and energy-related missions. Laboratory Environmental Governing Policy What is the Environmental Management System? It covers every program in the Laboratory

474

Standard-C hydrogen monitoring system, system design description  

SciTech Connect

Standard-C cabinet arrangement system design description for the Standard Hydrogen Monitoring System.

Schneider, T.C., Westinghouse Hanford

1996-08-29T23:59:59.000Z

475

Fiscal system analysis â?? contractual systems  

Science Journals Connector (OSTI)

Production sharing contracts are one of the most popular forms of contractual system used in petroleum agreements around the world, but the manner in which the fiscal terms and contract parameters impact system measures is complicated and not well understood. The purpose of this paper is to quantify the influence of private and market uncertainty in contractual fiscal systems. A meta-modelling approach is employed that couples the results of a simulation model with regression analysis to construct numerical functionals that quantify the fiscal regime. Relationships are derived that specify how the present value, rate of return, and take statistics vary as a function of the system parameters. The deepwater Girassol field development in Angola is taken as a case study.

Mark J. Kaiser

2006-01-01T23:59:59.000Z

476

Electricity Distribution System Workshop  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Discussion Summary Discussion Summary Electricity Transmission System Workshop 1 Grid Tech Team Discussion Summary Electricity Transmission System Workshop 2 Table of Contents INTRODUCTION ............................................................................................................................................. 3 EXECUTIVE SUMMARY .................................................................................................................................. 4 Process ...................................................................................................................................................... 4 Synthesized Challenges ............................................................................................................................. 5

477

Supply Systems Analyst  

Energy.gov (U.S. Department of Energy (DOE))

In this position you will serve as a Supply Systems Analyst for Supply Chain Services. The incumbent is responsible for managing and supporting multiple electronic database systems, including Asset...

478

Insulation Monitoring Systems  

Science Journals Connector (OSTI)

In this chapter there is presented general information on insulation deterioration signalization systems for AC IT networks. Few systems of continuous insulation supervision are described. The old concepts includ...

Piotr Olszowiec

2013-01-01T23:59:59.000Z

479

Modular optical detector system  

DOE Patents (OSTI)

A modular optical detector system. The detector system is designed to detect the presence of molecules or molecular species by inducing fluorescence with exciting radiation and detecting the emitted fluorescence. Because the system is capable of accurately detecting and measuring picomolar concentrations it is ideally suited for use with microchemical analysis systems generally and capillary chromatographic systems in particular. By employing a modular design, the detector system provides both the ability to replace various elements of the detector system without requiring extensive realignment or recalibration of the components as well as minimal user interaction with the system. In addition, the modular concept provides for the use and addition of a wide variety of components, including optical elements (lenses and filters), light sources, and detection means, to fit particular needs.

Horn, Brent A. (Livermore, CA); Renzi, Ronald F. (Tracy, CA)

2006-02-14T23:59:59.000Z

480

Oxford System 400  

NLE Websites -- All DOE Office Websites (Extended Search)

Oxford Plasmalab System 400 Sputtering System For questions concerning this machines capabilities, please contact Varshni Singh, at 578-0248. ecr.jpg (48456 bytes)  : ecr1.jpg...

Note: This page contains sample records for the topic "gathering system rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Design of assembly systems  

Science Journals Connector (OSTI)

The success of any assembly system depends on the translation of its design into an implemented working facility. The purpose of this chapter is to describe and explain the system elements and how they are com...

Shimon Y. Nof; Wilbert E. Wilhelm; Hans-Jürgen Warnecke

1997-01-01T23:59:59.000Z

482

Energy systems transformation  

Science Journals Connector (OSTI)

Energy systems transformation 10...associated with the incumbent energy economy that is unlikely to...its gatekeepers, such as auditors, analysts, debt-rating...problems generated by the energy system became more visible...

A. T. C. Jérôme Dangerman; Hans Joachim Schellnhuber

2013-01-01T23:59:59.000Z

483

Solar powered desalination system  

E-Print Network (OSTI)

17 1.2.4 Reverse Osmosis…………………………………………………19 1.345 Chapter 2: Reverse Osmosis System…………………………………………………….46 2.1 Reverse Osmosis System Set Up…………………………………………….46 2.2

Mateo, Tiffany Alisa

2011-01-01T23:59:59.000Z

484

Residential Geothermal Systems Credit  

Energy.gov (U.S. Department of Energy (DOE))

A resident individual taxpayer of Montana who installs a geothermal heating or cooling system in their principal dwelling can claim a tax credit based on the installation costs of the system, not...

485

Crowd-powered systems  

E-Print Network (OSTI)

Crowd-powered systems combine computation with human intelligence, drawn from large groups of people connecting and coordinating online. These hybrid systems enable applications and experiences that neither crowds nor ...

Bernstein, Michael Scott

2012-01-01T23:59:59.000Z

486

Systems Analysis Workshop Agenda  

Energy.gov (U.S. Department of Energy (DOE))

Agenda from DOE Systems Analysis Workshop held in Washington, D.C. July 28-29, 2004 to discuss and define role of systems analysis in DOE Hydrogen Program.

487

Energy systems transformation  

Science Journals Connector (OSTI)

...Energy System. The alternative energy system comprises solar, wind, geothermal, and hydro energy; among its associated technologies...lock-in effects. Also, rising costs caused by scarcity of energy sources or expensive and proliferating...

A. T. C. Jérôme Dangerman; Hans Joachim Schellnhuber

2013-01-01T23:59:59.000Z

488

Automobile Electrical Systems  

Science Journals Connector (OSTI)

The modern electrical system has been developed, over a period of some fifty years from the days of the early motor-car which usually had only one electrical system, namely, that of the ignition comp...

Arthur W. Judge

1970-01-01T23:59:59.000Z

489

Evolution of Web Systems  

Science Journals Connector (OSTI)

The World Wide Web has led to a new kind of software, web systems, which are based on web technologies. Just like software in other domains, web systems have evolution challenges. This chapter discusses evolution...

Holger M. Kienle; Damiano Distante

2014-01-01T23:59:59.000Z

490

Channels and sources used to gather equine-related information by college-age horse owners and enthusiasts  

E-Print Network (OSTI)

on different channels/sources. Face-to-face communication was important to both groups. Magazines were important to competitive participants, while the Internet was important to recreational participants. Competitive participants doubted the trustworthiness...

Sullivan, Erin Alene

2009-05-15T23:59:59.000Z

491

Fuel washout detection system  

DOE Patents (OSTI)

A system for detecting grossly failed reactor fuel by detection of particulate matter as accumulated on a filter.

Colburn, Richard P. (Pasco, WA)

1985-01-01T23:59:59.000Z

492

Performance Tested Comfort Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Showerheads Residential Weatherization Performance Tested Comfort Systems Ductless Heat Pumps New Construction Residential Marketing Toolkit Retail Sales Allocation Tool...

493

Monitoring System Performance (Presentation)  

SciTech Connect

Requirements for a standard test to rate the durability of photovoltaic (PV) modules at system voltage are discussed.

Emery, K.; Smith, R.

2011-02-01T23:59:59.000Z

494

Energy Storage Systems  

SciTech Connect

Energy Storage Systems – An Old Idea Doing New Things with New Technology article for the International Assoication of ELectrical Inspectors

Conover, David R.

2013-12-01T23:59:59.000Z

495

Directives System Manual  

Directives, Delegations, and Requirements

This Manual provides detailed requirements to supplement DOE O 251.1A, Directives System, dated 1-30-98.

1998-01-30T23:59:59.000Z

496

Enhanced Geothermal Systems  

Energy.gov (U.S. Department of Energy (DOE))

Below are the project presentations and respective peer review results for Engineered Geothermal Systems, Low Temperature and Exploration Demonstration Projects.

497

Match Pumps to System Requirements  

SciTech Connect

BestPractices Program tip sheet discussing pumping system efficiency matching pumps to system requirements

Not Available

2005-10-01T23:59:59.000Z

498

DOE Systems Engineering Methodology  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Computer System Retirement Guidelines Computer System Retirement Guidelines Version 3 September 2002 U.S. Department of Energy Office of the Chief Information Officer Computer System Retirement Guidelines Date: September 2002 Page 1 Rev Date: Table of Contents Section Page Purpose ............................................................................................................................................ 2 Initiation and Distribution ............................................................................................................... 2 Resource .......................................................................................................................................... 2 General Information ........................................................................................................................

499

On Analogue TMR System  

Science Journals Connector (OSTI)

This chapter presents a reliability model of the TMR Triple Modular Redundancy system based on analogue measurement channels. While reliability modelling of the standard TMR system based on digital channels has been well described in many previous publications, ... Keywords: Fault Detection Voter FDV, Fault-Tolerant System, Redundancy, Reliability, Triple Modular Redundancy TMR

Pavel Kucera

2012-10-01T23:59:59.000Z

500

Energy Systems Laboratory Groundbreaking  

ScienceCinema (OSTI)

INL recently broke ground for a research facility that will house research programs for bioenergy, advanced battery systems, and new hybrid energy systems that integrate renewable, fossil and nuclear energy sources. Here's video from the groundbreaking ceremony for INL's new Energy Systems Laboratory. You can learn more about CAES research at http://www.facebook.com/idahonationallaboratory.

Hill, David; Otter, C.L.; Simpson, Mike; Rogers, J.W.;

2013-05-28T23:59:59.000Z