National Library of Energy BETA

Sample records for gas oils heavy

  1. Upgrading heavy gas oils

    SciTech Connect (OSTI)

    Ferguson, S.; Reese, D.D.

    1986-05-20

    A method is described of neutralizing the organic acidity in heavy gas oils to produce a neutralization number less than 1.0 whereby they are rendered suitable as lube oil feed stocks which consists essentially of treating the heavy gas oils with a neutralizing amount of monoethanolamine to form an amine salt with the organic acids and then heating the thus-neutralized heavy gas oil at a temperature at least about 25/sup 0/F greater than the boiling point of water and for a time sufficient to convert the amine salts to amides.

  2. Process for upgrading heavy oils

    SciTech Connect (OSTI)

    LePage, J.F.; Marlino, G.

    1983-07-05

    The viscosity of heavy oils is reduced in order to facilitate pipe line transportation thereof. A fraction of the heavy oil is deasphalted in the presence of C/sub 5/-C/sub 7/ hydrocarbons, a portion of the separated asphalt is converted to synthesis gas, at least a portion of said gas is used to manufacture an alcohol mixture including methanol and C/sub 2/ to C/sub 10/ alcohols, which mixture is admixed with the heavy oil before transportation thereof. This procedure is more beneficial to the transported heavy oil than the prior processes which do not comprise the conversion of the asphalt fraction of the heavy oil.

  3. Utah Heavy Oil Program

    SciTech Connect (OSTI)

    J. Bauman; S. Burian; M. Deo; E. Eddings; R. Gani; R. Goel; C.K. Huang; M. Hogue; R. Keiter; L. Li; J. Ruple; T. Ring; P. Rose; M. Skliar; P.J. Smith; J.P. Spinti; P. Tiwari; J. Wilkey; K. Uchitel

    2009-10-20

    The Utah Heavy Oil Program (UHOP) was established in June 2006 to provide multidisciplinary research support to federal and state constituents for addressing the wide-ranging issues surrounding the creation of an industry for unconventional oil production in the United States. Additionally, UHOP was to serve as an on-going source of unbiased information to the nation surrounding technical, economic, legal and environmental aspects of developing heavy oil, oil sands, and oil shale resources. UHOP fulGilled its role by completing three tasks. First, in response to the Energy Policy Act of 2005 Section 369(p), UHOP published an update report to the 1987 technical and economic assessment of domestic heavy oil resources that was prepared by the Interstate Oil and Gas Compact Commission. The UHOP report, entitled 'A Technical, Economic, and Legal Assessment of North American Heavy Oil, Oil Sands, and Oil Shale Resources' was published in electronic and hard copy form in October 2007. Second, UHOP developed of a comprehensive, publicly accessible online repository of unconventional oil resources in North America based on the DSpace software platform. An interactive map was also developed as a source of geospatial information and as a means to interact with the repository from a geospatial setting. All documents uploaded to the repository are fully searchable by author, title, and keywords. Third, UHOP sponsored Give research projects related to unconventional fuels development. Two projects looked at issues associated with oil shale production, including oil shale pyrolysis kinetics, resource heterogeneity, and reservoir simulation. One project evaluated in situ production from Utah oil sands. Another project focused on water availability and produced water treatments. The last project considered commercial oil shale leasing from a policy, environmental, and economic perspective.

  4. Hydrofining of Athabasca derived heavy gas oil over Ni-W and Co-Mo catalysts

    SciTech Connect (OSTI)

    Mann, R.S.; Diaz-real, R.

    1987-01-01

    The hydrotreatment of heavy gas oil derived from Athabasca bitumen was studied in a trickle bed reactor over Ni-W and Co-Mo zeolite catalyst at 350-425/sup 0/C, 3.55 to 10.44 MPa, and LHSV of 1-4. The effects of temperature and liquid flow rates on the product were investigated. ASTM distillation, aniline point, viscosities and densities of the product oil were measured and correlated with various parameters. Activity of the catalysts for hydrodenitrogenation is compared.

  5. Conversion of heavy hydrocarbon oils

    SciTech Connect (OSTI)

    Chen, N.Y.; Pelrine, B.P.; Yan, T.Y.

    1982-12-14

    This invention provides a process for upgrading a heavy hydrocarbon oil to motor fuel products. The heavy hydrocarbon oil is admixed with a metal halide catalyst and a solvent component under supercritical conditions to form (1) a dense-gas solvent phase which contains refined hydrocarbon crackate, and which is substantially free of metal halide catalyst content; and (2) a residual asphaltic phase.

  6. Water issues associated with heavy oil production.

    SciTech Connect (OSTI)

    Veil, J. A.; Quinn, J. J.; Environmental Science Division

    2008-11-28

    Crude oil occurs in many different forms throughout the world. An important characteristic of crude oil that affects the ease with which it can be produced is its density and viscosity. Lighter crude oil typically can be produced more easily and at lower cost than heavier crude oil. Historically, much of the nation's oil supply came from domestic or international light or medium crude oil sources. California's extensive heavy oil production for more than a century is a notable exception. Oil and gas companies are actively looking toward heavier crude oil sources to help meet demands and to take advantage of large heavy oil reserves located in North and South America. Heavy oil includes very viscous oil resources like those found in some fields in California and Venezuela, oil shale, and tar sands (called oil sands in Canada). These are described in more detail in the next chapter. Water is integrally associated with conventional oil production. Produced water is the largest byproduct associated with oil production. The cost of managing large volumes of produced water is an important component of the overall cost of producing oil. Most mature oil fields rely on injected water to maintain formation pressure during production. The processes involved with heavy oil production often require external water supplies for steam generation, washing, and other steps. While some heavy oil processes generate produced water, others generate different types of industrial wastewater. Management and disposition of the wastewater presents challenges and costs for the operators. This report describes water requirements relating to heavy oil production and potential sources for that water. The report also describes how water is used and the resulting water quality impacts associated with heavy oil production.

  7. Retrofitting heavy oil processes

    SciTech Connect (OSTI)

    Hamilton, G.L.; Fitzgerald, M.; D'Amico, V.

    1986-01-01

    Refiners, faced with the need to process the bottom end of the heavy high sulfur crude oil barrel in today's uncertain economic environment, are reluctant to commit large amounts of money to expensive upgrading processes. In order to conserve scarce capital while improving operating margins, additional valuable products can be produced by retrofits such as conversion of an idle crude unit to visbreaking, delayed coking or deasphalting service, or conversion of hydrodesulfurizers to mild hydrocracking.

  8. Unconventional Oil and Gas Resources

    SciTech Connect (OSTI)

    2006-09-15

    World oil use is projected to grow to 98 million b/d in 2015 and 118 million b/d in 2030. Total world natural gas consumption is projected to rise to 134 Tcf in 2015 and 182 Tcf in 2030. In an era of declining production and increasing demand, economically producing oil and gas from unconventional sources is a key challenge to maintaining global economic growth. Some unconventional hydrocarbon sources are already being developed, including gas shales, tight gas sands, heavy oil, oil sands, and coal bed methane. Roughly 20 years ago, gas production from tight sands, shales, and coals was considered uneconomic. Today, these resources provide 25% of the U.S. gas supply and that number is likely to increase. Venezuela has over 300 billion barrels of unproven extra-heavy oil reserves which would give it the largest reserves of any country in the world. It is currently producing over 550,000 b/d of heavy oil. Unconventional oil is also being produced in Canada from the Athabasca oil sands. 1.6 trillion barrels of oil are locked in the sands of which 175 billion barrels are proven reserves that can be recovered using current technology. Production from 29 companies now operating there exceeds 1 million barrels per day. The report provides an overview of continuous petroleum sources and gives a concise overview of the current status of varying types of unconventional oil and gas resources. Topics covered in the report include: an overview of the history of Oil and Natural Gas; an analysis of the Oil and Natural Gas industries, including current and future production, consumption, and reserves; a detailed description of the different types of unconventional oil and gas resources; an analysis of the key business factors that are driving the increased interest in unconventional resources; an analysis of the barriers that are hindering the development of unconventional resources; profiles of key producing regions; and, profiles of key unconventional oil and gas producers.

  9. Ultrapyrolytic upgrading of plastic wastes and plastics/heavy oil mixtures to valuable light gas products

    SciTech Connect (OSTI)

    Lovett, S.; Berruti, F.; Behie, L.A.

    1997-11-01

    Viable operating conditions were identified experimentally for maximizing the production of high-value products such as ethylene, propylene, styrene, and benzene, from the ultrapyrolysis of waste plastics. Using both a batch microreactor and a pilot-plant-sized reactor, the key operating variables considered were pyrolysis temperature, product reaction time, and quench time. In the microreactor experiments, polystyrene (PS), a significant component of waste plastics, was pyrolyzed at temperatures ranging from 800 to 965 C, with total reaction times ranging from 500 to 1,000 ms. At a temperature of 965 C and 500 ms, the yields of styrene plus benzene were greater than 95 wt %. In the pilot-plant experiments, the recently patented internally circulating fluidized bed (ICFB) reactor (Milne et al., US Patent Number 5,370,789, 1994b) was used to ultrapyrolyze low-density polyethylene (LDPE) in addition to LDPE (5% by weight)/heavy oil mixtures at a residence time of 600 ms. Both experiments produced light olefin yields greater than 55 wt % at temperatures above 830 C.

  10. Oil & Gas Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oil & Gas Research Unconventional Resources NETL's onsite research in unconventional ... quantify potential risks associated with oil and gas resources in shale reservoirs that ...

  11. Oil and Gas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oil and Gas Oil and Gas R&D focus on the use of conventional and unconventional fossil fuels, including associated environmental challenges Contact thumbnail of Business ...

  12. Heavy oil transportation by pipeline

    SciTech Connect (OSTI)

    Gerez, J.M.; Pick, A.R.

    1996-12-31

    Worldwide there are a number of pipelines used to transport heavy crude oils. The operations are facilitated in a variety of ways. For example, the Alyeska pipeline is an insulated pipeline transporting warm oil over 800 miles. This 48-inch line experiences limited heat loss due to the insulation, volume of oil contained, and heat gain due to friction and pumping. Some European trunk lines periodically handle heavy and waxy crudes. This is achieved by proper sizing of batches, following waxy crudes with non-waxy crudes, and increased use of scrapers. In a former Soviet republic, the transportation of heavy crude oil by pipeline has been facilitated by blending with a lighter Siberian crude. The paper describes the pipeline transport of heavy crudes by Interprovincial Pipe Line Inc. The paper describes enhancing heavy oil transportation by emulsion formation, droplet suspension, dilution, drag reducing agents, and heating.

  13. Advances in heavy oil hydroprocessing

    SciTech Connect (OSTI)

    Mendizabal, O.B. )

    1988-06-01

    The world increase in heavy crudes has forced refiners to develop different processes that upgrade the yields and product properties recovered from these crudes. However, some of the optimized and new processes are not able to handle whole heavy crude oils, due to the high viscosity and corrosion of their long and short residues. The different processes for heavy crudes can be classified in two areas: physical (vg. Liquid Extraction) and chemical processes. The catalytic hydrotreating process, which belongs to this last classification, has demonstrated to be an economical upgrading process for heavy crude oil. This paper describes the development by the Mexican Petroleum Institute of the process to hydrotreat maya heavy crude. The effect of the operating conditions, the catalyst ---- development and the technical - economical analysis are presented. The product properties and yields are compared with the results obtained with light crude oil like isthmus.

  14. 31443,"AECTRA REFG & MKTG",1,840,"UNFINISHED OILS, HEAVY GAS...

    U.S. Energy Information Administration (EIA) Indexed Site

    PETRO",1,133,"MOTOR GAS, FINISHED UNLEADED",1001,"NEW YORK, NY","NEW YORK",1,830,"SPAIN",192,0,0,,,,, 31443,"DELPHI PETRO",2,133,"MOTOR GAS, FINISHED UNLEADED",1002,"ALBANY,...

  15. Process for removing heavy metal compounds from heavy crude oil

    DOE Patents [OSTI]

    Cha, Chang Y.; Boysen, John E.; Branthaver, Jan F.

    1991-01-01

    A process is provided for removing heavy metal compounds from heavy crude oil by mixing the heavy crude oil with tar sand; preheating the mixture to a temperature of about 650.degree. F.; heating said mixture to up to 800.degree. F.; and separating tar sand from the light oils formed during said heating. The heavy metals removed from the heavy oils can be recovered from the spent sand for other uses.

  16. Upgrading Orinoco belt heavy oil

    SciTech Connect (OSTI)

    Alcantara, J.; Castillo, O.

    1982-09-01

    The Orinoco Heavy Oil Belt of Venezuela is a subsurface geological formation of petroleum-bearing sands that is approximately 700 km long and between 60 and 80 km wide. The results of recent explorations have shown the area to contain over one trillion barrels of oil in-place, ranging from 8/sup 0/ API to 14/sup 0/ APE gravity. In an effort to develop these resources, Petroleos de Venezuela has undertaken a program to evaluate and develop this heavy oil belt. The objectives of this program are discussed along with the process technology selection, pilot plants, and environmental protection measures. (JMT)

  17. Process for stimulating and upgrading the oil production from a heavy oil reservoir

    SciTech Connect (OSTI)

    Sweany, G.A.

    1981-08-18

    A process for thermally stimulating and upgrading oil production from a heavy oil reservoir wherein the heavy oil produced from the reservoir is combined with a hydrogen donor diluent and the mixture is subjected to thermal cracking to upgrade the heavy oil into more valuable hydrocarbon products. The cracked products are fractionated into a light end vapor fraction, an intermediate liquid fraction, a gas oil fraction and a pitch fraction, and at least a portion of the gas oil fraction is hydrogenated by contacting it with a hydrogen-containing gas stream to produce the hydrogen donor diluent combined with the heavy oil. The pitch fraction is subjected to partial oxidation to produce the hydrogen-containing gas stream and a by-product gas stream containing steam which is combined with additional steam and injected into the heavy oil reservoir to enhance the mobility of heavy oil contained therein. The light end vapor fraction and unreacted hydrogen-containing gas produced by the process are utilized as fuel in the process. The intermediate liquid fraction produce and portion of the gas oil fraction not hydrogenated are readily transportable from the process.

  18. Heavy oil expansions gather momentum worldwide

    SciTech Connect (OSTI)

    Moritis, G.

    1995-08-14

    Cold production, wormholes, foamy oil mechanism, improvements in thermal methods, and horizontal wells are some of the processes and technologies enabling expansion of the world`s heavy oil/bitumen production. Such processes were the focus of the International Heavy Oil Symposium in Calgary, June 19--21. Unlike conventional oil production, heavy oil/bitumen extraction is more a manufacturing process where technology enables the business and does not just add value. The current low price spreads between heavy oil/light oil indicate that demand for heavy oil is high. The paper first discusses the price difference between heavy and light oils, then describes heavy oil production activities in Canada at Cold Lake, in Venezuela in the Orinoco belt, and at Kern River in California.

  19. heavy_oil | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Heavy Oil Heavy oil is a vast U.S. oil resource that is underexploited because its highly viscous nature renders it difficult to produce and to refine. As higher-gravity crudes (lighter oil) become increasingly scarce in the U.S., American operators are looking more and more to low-gravity crudes (heavy oil) to prop up the Nation's declining oil output. Heavy oil generally is defined as having an API (American Petroleum Institute) gravity of 10-20 degrees. Oil sources with even lower gravities,

  20. Upgrading Orinoco Belt heavy oil

    SciTech Connect (OSTI)

    Aliantara, J.; Castillo, O.

    1982-05-01

    Petroleos de Venezuela, S.A. (PDVSA), in an effort to develop new oil resources, has undertaken a program to evaluate and develop the Orinoco Heavy Oil Belt, in the eastern part of Venezuela. Lagoven, S.A., a subsidiary of PDVSA, has been assigned the responsibility for developing and upgrading part of the Orinoco belt. This paper describes the most relevant aspects of Lagoven's first upgrading module, a facility that will convert Orinoco oil into a premium crude with a very high yield of products of great market demand.

  1. Impact and future of heavy oil produciton

    SciTech Connect (OSTI)

    Olsen, D.K, )

    1996-01-01

    Heavy oil resources are becoming increaingly important in meeting world oil demand. Heavy oil accounts for 10% of the worlds current oil production and is anticipated to grow significantly. Recent narrowing of the price margins between light and heavy oil and the development of regional heavy oil markets (production, refining and marketing) have prompted renewed investment in heavy oil. Production of well known heavy oil resources of Canada, Venezuela, United States, and elsewhere throughout the world will be expanded on a project-by-project basis. Custom refineries designed to process these heavy crudes are being expanded. Refined products from these crudes will be cleaner than ever before because of the huge investment. However, heavy oil still remains at a competitive disadvantage due to higher production, transportation and refining have to compete with other investment opportunities available in the industry. Expansion of the U.S. heavy oil industry is no exception. Relaxation of export restrictions on Alaskan North Slope crude has prompted renewed development of California's heavy oil resources. The location, resource volume, and oil properties of the more than 80-billion barrel U.S. heavy oil resource are well known. Our recent studies summarize the constraints on production, define the anticipated impact (volume, location and time frame) of development of U.S. heavy oil resources, and examines the $7-billion investment in refining units (bottoms conversion capacity) required to accommodate increased U.S. heavy oil production. Expansion of Canadian and Venezuelan heavy oil and tar sands production are anticipated to dramatically impact the U.S. petroleum market while displacing some imported Mideast crude.

  2. Impact and future of heavy oil produciton

    SciTech Connect (OSTI)

    Olsen, D.K,

    1996-12-31

    Heavy oil resources are becoming increaingly important in meeting world oil demand. Heavy oil accounts for 10% of the worlds current oil production and is anticipated to grow significantly. Recent narrowing of the price margins between light and heavy oil and the development of regional heavy oil markets (production, refining and marketing) have prompted renewed investment in heavy oil. Production of well known heavy oil resources of Canada, Venezuela, United States, and elsewhere throughout the world will be expanded on a project-by-project basis. Custom refineries designed to process these heavy crudes are being expanded. Refined products from these crudes will be cleaner than ever before because of the huge investment. However, heavy oil still remains at a competitive disadvantage due to higher production, transportation and refining have to compete with other investment opportunities available in the industry. Expansion of the U.S. heavy oil industry is no exception. Relaxation of export restrictions on Alaskan North Slope crude has prompted renewed development of California`s heavy oil resources. The location, resource volume, and oil properties of the more than 80-billion barrel U.S. heavy oil resource are well known. Our recent studies summarize the constraints on production, define the anticipated impact (volume, location and time frame) of development of U.S. heavy oil resources, and examines the $7-billion investment in refining units (bottoms conversion capacity) required to accommodate increased U.S. heavy oil production. Expansion of Canadian and Venezuelan heavy oil and tar sands production are anticipated to dramatically impact the U.S. petroleum market while displacing some imported Mideast crude.

  3. heavy_oil | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Much of America's heavy oil is produced via a costly steam injection enhanced oil recovery (EOR) method to produce a crude oil grade that is lower in quality and thus sells for ...

  4. China shows increasing interest in heavy oil and oil sands

    SciTech Connect (OSTI)

    Not Available

    1986-12-01

    China and Canadian and US groups are cooperating in several areas to develop the heavy oil, asphalt, and oil sand deposits of China. The agreements dealing with exploration and upgrading are briefly described. The majority of the paper describes the occurrences of heavy oil, asphalt, and oil sands in China. 1 figure.

  5. Heavy crude upgrading using remote natural gas

    SciTech Connect (OSTI)

    Grosboll, M.P.

    1991-12-03

    This paper describes a method of forming an upgraded crude. It comprises: forming hydrogen from methane gas for hydroconverting heavy crude to form a better crude and reduce its viscosity; hydrogenating under hydroconverting conditions of 650 degrees Fahrenheit ({degrees}F)-1000{degrees}F; and 500-3000 pounds per square inch gauge (psig) only a first portion of a crude oil stream less than the total crude oil stream to produce a light oil that has a lowered viscosity; admixing the light oil with the remainder of the crude oil stream not hydrogenated to produce a flowable crude; and transporting the flowable crude to a refinery including a substep of flowing the crude through a pipeline.

  6. NETL: Oil & Gas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oil & Gas Efficient recovery of our nation's fossil fuel resources in an environmentally safe manner requires the development and application of new technologies that address the unique nature and challenging locations of many of our remaining oil and natural gas accumulations. The National Energy Technology Laboratory's (NETL) research projects are designed to help catalyze the development of these new technologies, provide objective data to help quantify the environmental and safety risks

  7. SOVENT BASED ENHANCED OIL RECOVERY FOR IN-SITU UPGRADING OF HEAVY OIL SANDS

    SciTech Connect (OSTI)

    Munroe, Norman

    2009-01-30

    With the depletion of conventional crude oil reserves in the world, heavy oil and bitumen resources have great potential to meet the future demand for petroleum products. However, oil recovery from heavy oil and bitumen reservoirs is much more difficult than that from conventional oil reservoirs. This is mainly because heavy oil or bitumen is partially or completely immobile under reservoir conditions due to its extremely high viscosity, which creates special production challenges. In order to overcome these challenges significant efforts were devoted by Applied Research Center (ARC) at Florida International University and The Center for Energy Economics (CEE) at the University of Texas. A simplified model was developed to assess the density of the upgraded crude depending on the ratio of solvent mass to crude oil mass, temperature, pressure and the properties of the crude oil. The simplified model incorporated the interaction dynamics into a homogeneous, porous heavy oil reservoir to simulate the dispersion and concentration of injected CO2. The model also incorporated the characteristic of a highly varying CO2 density near the critical point. Since the major challenge in heavy oil recovery is its high viscosity, most researchers have focused their investigations on this parameter in the laboratory as well as in the field resulting in disparaging results. This was attributed to oil being a complex poly-disperse blend of light and heavy paraffins, aromatics, resins and asphaltenes, which have diverse behaviors at reservoir temperature and pressures. The situation is exacerbated by a dearth of experimental data on gas diffusion coefficients in heavy oils due to the tedious nature of diffusivity measurements. Ultimately, the viscosity and thus oil recovery is regulated by pressure and its effect on the diffusion coefficient and oil swelling factors. The generation of a new phase within the crude and the differences in mobility between the new crude matrix and the

  8. Design of heavy oil upgrading units

    SciTech Connect (OSTI)

    Farrell, W.D.; Phodes, R.P.; Zeno, D.Y.

    1985-01-01

    Heavy oil upgrading has become an increasingly important aspect of ER and E's research. Due to high costs of experimental catalysts, small catalyst charges are used (20-150cc). Tubular design and tree-stage stirred design are discussed with emphasis on the techniques and equipment used to handle heavy oil. Mechanical design and fluid mechanics are discussed.

  9. EXPERIMENTAL AND THEORETICAL DETERMINATION OF HEAVY OIL VISCOSITY...

    Office of Scientific and Technical Information (OSTI)

    OF HEAVY OIL VISCOSITY UNDER RESERVOIR CONDITIONS Citation Details In-Document Search Title: EXPERIMENTAL AND THEORETICAL DETERMINATION OF HEAVY OIL VISCOSITY UNDER ...

  10. Heavy oil catalytic cracking process and apparatus (Patent) ...

    Office of Scientific and Technical Information (OSTI)

    Heavy oil catalytic cracking process and apparatus Citation Details In-Document Search Title: Heavy oil catalytic cracking process and apparatus This paper describes a fluidized ...

  11. Deepwater Oil & Gas Resources | Department of Energy

    Office of Environmental Management (EM)

    Deepwater Oil & Gas Resources Deepwater Oil & Gas Resources The United States has significant natural gas and oil reserves. But many of these resources are increasingly harder to ...

  12. Finding Hidden Oil and Gas Reserves

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Finding Hidden Oil and Gas Reserves Finding Hidden Oil and Gas Reserves Key Challenges: Seismic imaging methods, vital in our continuing search for deep offshore oil and gas...

  13. Deepwater Oil & Gas Resources | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Deepwater Oil & Gas Resources Deepwater Oil & Gas Resources The United States has significant natural gas and oil reserves. But many of these resources are increasingly harder to...

  14. Upgrading petroleum residues and heavy oils

    SciTech Connect (OSTI)

    Gray, M.R.

    1994-01-01

    Here is an in-depth look at current techniques for converting heavy oils and residues into more valuable distillates. It examines the chemistry of heavy hydrocarbon feeds and their properties which are important to engineering design, including phase behavior, reaction kinetics, and thermodynamic and transport characteristics.

  15. Research Portfolio Report Unconventional Oil & Gas Resources...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Unconventional Oil & Gas Resources: Subsurface Geology and Engineering DOENETL-20151691 ... Research Portfolio Report: Unconventional Oil & Gas Resources Executive Summary S ...

  16. The microbial upgrading of model heavy oils

    SciTech Connect (OSTI)

    Webster, I.A.; Patras, L.E. )

    1988-01-01

    The authors have isolated bacteria and used them to catalyze the removal of sulfur, nitrogen and nickel from model heavy oils and asphaltenes. Their paper will discuss their activity and reactor concepts. The concept of a membrane bioreactor for oil processing is introduced.

  17. Pipeline transportation of heavy crude oil

    SciTech Connect (OSTI)

    Kessick, M.A.; St. Denis, C.E.

    1982-08-10

    Heavy crude oils are transported by pipeline from deposit location to a remote upgrading location by emulsifying the crude oil using deaerated sodium hydroxide solution, conveying the oilin-water emulsion through the pipeline, and recovery of the oil from the oil-in-water emulsion by inverting the emulsion and dewatering the resulting water-in-oil emulsion. The emulsion inversion may be effected using slaked lime, resulting in recovery of a substantial proportion of the sodium hydroxide used in the initial emulsification. The sodium hydroxide solution may be recycled by a separate pipeline for reuse or treated for discharge.

  18. Assessment of heavy oil conversion

    SciTech Connect (OSTI)

    Gleim, W.T.K.

    1983-08-01

    Removal of benzene insoluble asphaltene components greatly facilitates and improves the subsequent upgrading of residual oils, the desulfurization in particular. For the upgrading of Venezualean oils, the Aurobon process is still the only feasible solution.

  19. Heavy Gas Dispersion Incompressible Flow

    Energy Science and Technology Software Center (OSTI)

    1992-01-27

    FEM3 is a numerical model developed primarily to simulate heavy gas dispersion in the atmosphere, such as the gravitational spread and vapor dispersion that result from an accidental spill of liquefied natural gas (LNG). FEM3 solves both two and three-dimensional problems and, in addition to the generalized anelastic formulation, includes options to use either the Boussinesq approximation or an isothermal assumption, when appropriate. The FEM3 model is composed of three parts: a preprocessor PREFEM3, themore » main code FEM3, and two postprocessors TESSERA and THPLOTX.« less

  20. Kinetics of heavy oil/coal coprocessing

    SciTech Connect (OSTI)

    Szladow, A.J.; Chan, R.K.; Fouda, S.; Kelly, J.F. )

    1988-01-01

    A number of studies have been reported on coprocessing of coal and oil sand bitumen, petroleum residues and distillate fractions in catalytic and non-catalytic processes. The studies described the effects of feedstock characteristics, process chemistry and operating variables on the product yield and distribution; however, very few kinetic data were reported in these investigations. This paper presents the kinetic data and modeling of the CANMET coal/heavy oil coprocessing process. A number of reaction networks were evaluated for CANMET coprocessing. The final choice of model was a parallel model with some sequential characteristics. The model explained 90.0 percent of the total variance, which was considered satisfactory in view of the difficulties of modeling preasphaltenes. The models which were evaluated showed that the kinetic approach successfully applied to coal liquefaction and heavy oil upgrading can be also applied to coprocessing. The coal conversion networks and heavy oil upgrading networks are interrelated via the forward reaction paths of preasphaltenes, asphaltenes, and THFI and via the reverse kinetic paths of an adduct formation between preasphaltenes and heavy oil.

  1. RESEARCH OIL RECOVERY MECHANISMS IN HEAVY OIL RESERVOIRS

    SciTech Connect (OSTI)

    Anthony R. Kovscek; William E. Brigham

    1999-06-01

    The United States continues to rely heavily on petroleum fossil fuels as a primary energy source, while domestic reserves dwindle. However, so-called heavy oil (10 to 20{sup o}API) remains an underutilized resource of tremendous potential. Heavy oils are much more viscous than conventional oils. As a result, they are difficult to produce with conventional recovery methods such as pressure depletion and water injection. Thermal recovery is especially important for this class of reservoirs because adding heat, usually via steam injection, generally reduces oil viscosity dramatically. This improves displacement efficiency. The research described here was directed toward improved understanding of thermal and heavy-oil production mechanisms and is categorized into: (1) flow and rock properties; (2) in-situ combustion; (3) additives to improve mobility control; (4) reservoir definition; and (5) support services. The scope of activities extended over a three-year period. Significant work was accomplished in the area of flow properties of steam, water, and oil in consolidated and unconsolidated porous media, transport in fractured porous media, foam generation and flow in homogeneous and heterogeneous porous media, the effects of displacement pattern geometry and mobility ratio on oil recovery, and analytical representation of water influx. Significant results are described.

  2. Geothermal and heavy-oil resources in Texas (Technical Report...

    Office of Scientific and Technical Information (OSTI)

    Geothermal and heavy-oil resources in Texas Citation Details In-Document Search Title: Geothermal and heavy-oil resources in Texas You are accessing a document from the ...

  3. Process for upgrading heavy hydrocarbonaceous oils

    SciTech Connect (OSTI)

    Fisher, I.P.; Souhrada, F.; Woods, H.J.

    1981-10-13

    An integrated upgrading process is disclosed which can be used to lower the specific gravity, viscosity and boiling range of heavy, viscous hydrocarbonaceous oil . The process consists of fractionally distilling the oil, treating its residuum with a hydrogen donor material under hydrocracking conditions, fractionally distilling the effluent from the hydrocracking zone and rehydrogenating that portion boiling from about 180/sup 0/ C to 350/sup 0/ C for recycling to the hydrocracking zone. The liquid portion of the oil not recycled can be recombined into a reconstituted crude suitable for transporting by normal crude pipelines.

  4. Heavy Gas Dispersion Incompressible Flow

    Energy Science and Technology Software Center (OSTI)

    1992-02-03

    FEM3 is a numerical model developed primarily to simulate heavy gas dispersion in the atmosphere, such as the gravitational spread and vapor dispersion that result from an accidental spill of liquefied natural gas (LNG). FEM3 solves both two and three-dimensional problems and, in addition to the generalized anelastic formulation, includes options to use either the Boussinesq approximation or an isothermal assumption, when appropriate. The FEM3 model is composed of three parts: a preprocessor PREFEM3, themore » main code FEM3, and two postprocessors TESSERA and THPLOTX. The DEC VAX11 version contains an auxiliary program, POLYREAD, which reads the polyplot file created by FEM3.« less

  5. Hydroprocessing catalysts for heavy oil and coal

    SciTech Connect (OSTI)

    Satriana, M.J.

    1982-01-01

    Hydroprocessing catalysts, as described in over 230 processes covered in this book, are hydrogenation catalysts used in the upgrading of heavy crudes and coal to products expected to be in great demand as the world's primary oil supplies gradually dwindle. The techniques employed in hydroprocessing result in the removal of contaminants, the transformation of lower grade materials such as heavy crudes to valuable fuels, or the conversion of hydrocarbonaceous solids into gaseous or liquid fuel products. All of these techniques are, of course, carried out in the presence of hydrogen. Some of the brightest energy prospects for the future lie in heavy oil reservoirs and coal reserves. Heavy oils, defined in this book as having gravities of < 20/sup 0/API, are crudes so thick that they are not readily extracted from their reservoirs. However, processing of these crudes is of great importance, because the US resource alone is enormous. The main types of processing catalysts covered in the book are hydrorefining catalysts plus some combinations of the two. Catalysts for the conversion of hydrocarbonaceous materials to gaseous or liquid fuels are also covered. The primary starting material for these conversions is coal, but wood, lignin, oil shale, tar sands, and peat are other possibilities. The final chapter describes the preparation of various catalyst support systems.

  6. Kinetics of heavy oil/coal coprocessing

    SciTech Connect (OSTI)

    Szladow, A.J.; Chan, R.K. ); Foudu, S.; Kelly, J.F. )

    1988-06-01

    A number of studies have been reported on coprocessing of coal and oil sand bitumen, petroleum residues and distillate fractions in catalytic and non-catalytic processes. The studies described the effects of feedstock characteristics, process chemistry and operating variables on the product yield and distribution; however, very few kinetic data were reported in these investigations. This paper presents the kinetic data and modelling of the CANMET coal/heavy oil coprocessing process. CANMET has been conducting research and process development work on coprocessing of Canadian heavy oil/bitumen and coal since 1979 including studies of the kinetics and mechanisms of coprocessing. As a continuation of the program, CANMET and Lobbe Technologies undertook a project on mathematical modelling of coprocessing kinetics with emphasis on the development of reaction engineering models for improved process performance and operation.

  7. Advanced Natural Gas Engine Technology for Heavy Duty Vehicles...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Natural Gas Engine Technology for Heavy Duty Vehicles Advanced Natural Gas Engine Technology for Heavy Duty Vehicles Natural gas engine technology has evolved to meet the ...

  8. Iran Oil and Gas | Open Energy Information

    Open Energy Info (EERE)

    Iran Oil and Gas Jump to: navigation, search Logo: Iran Oil and Gas Name: Iran Oil and Gas Address: Unit 16, 3rd Fl., Bldg. No. 2, 9th Narenjestan St., North Pasdaran Ave. Place:...

  9. Heavy oil. upgrading integrated with steam drive

    SciTech Connect (OSTI)

    Van Driesen, R.; Viens, C.H.; Fornoff, L.L.

    1980-01-01

    A study of the upgrading of heavy oil from a representative Venezuelan Jobo crude (9.2/sup 0/API, 4.1% sulfur, and 500 ppm total metals) from the Orinoco area involved 110 computer simulations based on a modified C-E Lummus Refinery Linear Program model on the assumptions of a 125,000 bbl/day refinery built, starting at 1979 prices, for completion by 1986 near the producing field to supply the fuel oil needed to provide oil field steam. All of the upgrading systems were economically attractive; the per cent return-on-investment (ROI) before taxes for the methods studied were: for Lummus LC-Fining, 135.9%; for Exxon's FLEXICOKING, 132.4%; for delayed coking, 119.2%; and for deasphalting, 106.5%. LC-Fining provided the best over-all combination of flexibility, product yield, product quality, and return on investment. The economics favored upgrading to the maximum extent possible; there was a reduction in the ROI for all the upgrading systems when product specifications were lowered from the premium base case (1.2% SO/sub 2/ emitted per million Btu fired). The premium upgraded heavy crude oils should be worth $3.00-$3.50/bbl more than comparable conventional crude oils, could be of up to 27/sup 0/API, and could be substituted, at up to 50%, for conventional crude oils in a typical U.S. refinery.

  10. Oil and Gas Gateway | Open Energy Information

    Open Energy Info (EERE)

    States, oil and gas boards and commissions are the place for finding data related to oil and gas activities. These activities include well records, permitting, and production...

  11. Oil and Gas Research| GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oil & Gas We're balancing the increasing demand for finite resources with technology that ensures access to energy for generations to come. Home > Innovation > Oil & Gas ...

  12. oil and gas portfolio reports

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Gas Research Portfolio Reports Natural Gas & Oil Program Research Portfolio Reports The Office of Fossil Energy (FE)/National Energy Technology Laboratory (NETL) is releasing a series of nine Research Portfolio Reports to provide a snapshot of results and accomplishments completed to-date for active and completed projects under three focus areas: Unconventional Oil & Gas Resources; Ultra-Deepwater; and Small Producers. The reports capture research conducted over the last ten years

  13. Recovery and upgrading of heavy oil analyzed

    SciTech Connect (OSTI)

    Fornoff, L.L.; Van Driesen, R.P.; Viens, C.H.

    1980-10-13

    An analysis has been made of recovery and upgrading of Venezuelan heavy crudes by integrating steam-drive production data with an upgraded computer processing program. A study used 110 computer cases to analyze a project using Venezuelan heavy crude from the Jobo field with gravity of 9.2 API and 4.1% by wt sulfur for the base case. Sensitivity cases used 12.2 API oil from the Lot 9 field, Monagas state, Venezuela, with sulfur content of 2.3%. Four upgrading methods were studied (deasphalting, delayed coking, flexicoking, and LC-fining), all with favorable resulting economics.

  14. Feasibility study of heavy oil recovery in the Permian Basin (Texas and New Mexico)

    SciTech Connect (OSTI)

    Olsen, D.K.; Johnson, W.I.

    1993-05-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production. Each report covers select areas of the United States. The Permian Basin of West Texas and Southeastern New Mexico is made up of the Midland, Delaware, Val Verde, and Kerr Basins; the Northwestern, Eastern, and Southern shelves; the Central Basin Platform, and the Sheffield Channel. The present day Permian Basin was one sedimentary basin until uplift and subsidence occurred during Pennsylvanian and early Permian Age to create the configuration of the basins, shelves, and platform of today. The basin has been a major light oil producing area served by an extensive pipeline network connected to refineries designed to process light sweet and limited sour crude oil. Limited resources of heavy oil (10`` to 20`` API gravity) occurs in both carbonate and sandstone reservoirs of Permian and Cretaceous Age. The largest cumulative heavy oil production comes from fluvial sandstones of the Cretaceous Trinity Group. Permian heavy oil is principally paraffinic and thus commands a higher price than asphaltic California heavy oil. Heavy oil in deeper reservoirs has solution gas and low viscosity and thus can be produced by primary and by waterflooding. Because of the nature of the resource, the Permian Basin should not be considered a major heavy oil producing area.

  15. Feasibility study of heavy oil recovery in the Permian Basin (Texas and New Mexico)

    SciTech Connect (OSTI)

    Olsen, D.K.; Johnson, W.I.

    1993-05-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production. Each report covers select areas of the United States. The Permian Basin of West Texas and Southeastern New Mexico is made up of the Midland, Delaware, Val Verde, and Kerr Basins; the Northwestern, Eastern, and Southern shelves; the Central Basin Platform, and the Sheffield Channel. The present day Permian Basin was one sedimentary basin until uplift and subsidence occurred during Pennsylvanian and early Permian Age to create the configuration of the basins, shelves, and platform of today. The basin has been a major light oil producing area served by an extensive pipeline network connected to refineries designed to process light sweet and limited sour crude oil. Limited resources of heavy oil (10'' to 20'' API gravity) occurs in both carbonate and sandstone reservoirs of Permian and Cretaceous Age. The largest cumulative heavy oil production comes from fluvial sandstones of the Cretaceous Trinity Group. Permian heavy oil is principally paraffinic and thus commands a higher price than asphaltic California heavy oil. Heavy oil in deeper reservoirs has solution gas and low viscosity and thus can be produced by primary and by waterflooding. Because of the nature of the resource, the Permian Basin should not be considered a major heavy oil producing area.

  16. Bitumen and heavy oil upgrading in Canada

    SciTech Connect (OSTI)

    Chrones, J. ); Germain, R.R. )

    1989-01-01

    A review is presented of the heavy oil upgrading industry in Canada. Up to now it has been based on the processing of bitumen extracted from oil sands mining operations at two sites, to produce a residue-free, low sulphur, synthetic crude. Carbon rejection has been the prime process technology with delayed coking being used by Suncor and FLUID COKING at Syncrude. Alternative processes for recovering greater amounts of synthetic crude are examined. These include a variety of hydrogen addition processes and combinations which produce pipelineable materials requiring further processing in downstream refineries with expanded capabilities. The Newgrade Energy Inc. upgrader now under construction in Regina, will use fixed-bed, catalytic, atmospheric-residue, hydrogen processing. Two additional projects, also based on hydrogenation, will use ebullated bed catalyst systems; the expansion of Syncrude, now underway, is using the LC Fining Process whereas the announced Husky Bi-Provincial upgrader is based on H-Oil.

  17. Bitumen and heavy oil upgrading in Canada

    SciTech Connect (OSTI)

    Chrones, J.

    1988-06-01

    A review is presented of the heavy oil upgrading industry in Canada. Up to now it has been based on the processing of bitumen extracted from oil sands mining operations at two sites, to produce a residue-free, low sulfur, synthetic crude. Carbon rejection has been the prime process technology with delayed coking being used by Suncor and FLUID COKING at Syncrude. Alternative processes for recovering greater amounts of synthetic crude are examined. These include a variety of hydrogen addition processes and combinations which produce pipelineable materials requiring further processing in downstream refineries with expanded capabilities. The Newgrade Energy Inc. upgrader, now under construction in Regina, will use fixed-bed, catalytic, atmospheric-residue, hydrogen processing. Two additional products, also based on hydrogenation, will use ebullated bed catalyst systems: the expansion of Syncrude, now underway, is using the LC Fining Process whereas the announced Husky Bi-Provincial upgrader is based on H-Oil.

  18. Combined process for heavy oil, upgrading and synthetic fuel production

    SciTech Connect (OSTI)

    Polomski, R.E.

    1984-06-05

    A process for upgrading heavy oil to fuel products comprises deasphalting the heavy oil with an oxygenated solvent and simultaneously converting the oxygenated solvent and deasphalted oil over a ZSM-5 type catalyst to produce gasoline and distillate boiling range hydrocarbons.

  19. Characterization of Venezuelan heavy oil vacuum residua

    SciTech Connect (OSTI)

    Izquierdo, A.; Carbognani, L.; Leon, V.; Parisi, A. )

    1988-06-01

    Characterization of abundant ''heavy'' feedstocks such as tar sands, heavy oils and vacuum residua will play a fundamental role in the use of these energy sources. Their physical and chemical properties vary from one feed to another, and this can have some consequences in their necessary upgrading processes. In this paper results on the characterization of 510/sup 0/C-vacuum residua (VR) obtained from Venezuelan Heavy and Medium Oils are presented. These are Morichal (Mo), Merey (Me), Guafita (Gu) and Barinas (Ba). The VR have all an API gravity between 3 and 6, more than 15% asphaltenes, metals above 200 ppm, as well as high contents of nitrogen, more than 6000 ppm, and sulphur, over 1%. It has been found that when these feeds are hydrotreated under similar conditions the processability improves in the order Ba

  20. Oil and Gas | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Jump to: navigation, search Oil and gas represents a non-renewable energy sector. Retrieved from "http:en.openei.orgwindex.php?titleOilandGas&oldid335172" ...

  1. Flexibility in heavy oil upgrading with unicracking/HDS technology

    SciTech Connect (OSTI)

    Hennig, H.; Baron, K.; Moorhead, E.L.; Smith, M.

    1984-03-01

    With petroleum reserves becoming heavier and the demand for bottom of the barrel products greatly reduced, refiners are increasing their capabilities to upgrade heavy oil. Many heavy oil upgrading options are available and the best strategy for each refiner is not obvious. The best approach will depend on the specific circumstances and goals of the refiner. This presentation discusses the relative merits of several heavy oil upgrading options utilizing the Unicracking/HDS process.

  2. Trends in heavy oil production and refining in California

    SciTech Connect (OSTI)

    Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II

    1992-07-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10{degrees} to 20{degrees} API gravity) production in California has increased from 20% of the state`s total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation`s energy production and refining capability. California is the recipient and refines most of Alaska`s 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources.

  3. Trends in heavy oil production and refining in California

    SciTech Connect (OSTI)

    Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II.

    1992-07-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10{degrees} to 20{degrees} API gravity) production in California has increased from 20% of the state's total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation's energy production and refining capability. California is the recipient and refines most of Alaska's 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources.

  4. Characteristics and upgrading technologies of Chinese heavy oil

    SciTech Connect (OSTI)

    Ghuang Yang; Jinsen Gao

    1995-12-31

    The characteristics of typical Chinese heavy oils produced in the eastern, northwestern, and northeastern parts of China are presented to show the uniqueness of heavy oils on the Chinese mainland. Henceforth, upgrading technologies of Chinese domestic heavy crudes are discussed along this line. Two main categories of upgrading technologies, decarbonization and hydrogenation, as realized or being developed in this country are presented. It is concluded that most Chinese heavy crudes are adaptable to conventional upgrading processes.

  5. Upgrading heavy oil using slurry processes

    SciTech Connect (OSTI)

    Del Bianco, A.; Panariti, N.; Marchionna, M.

    1995-11-01

    There is a growing interest in processes capable of converting heavy feedstocks (petroleum residues and heavy oils) into lower boiling products of high quality. The operational problems of upgrading heavy feeds relate to the presence of sulfur, nitrogen, metals, and considerable amounts of Conradson carbon residue. An efficient residue conversion process must be able to reduce the molecular weight of the feedstocks to material with boiling points below 550 C, increase the H-to-C ratio of the refined product, and remove heteroatoms and metals. Whereas the molecular weight reduction is normally achieved by C-C bond cracking above 400 C, often in the presence of acid catalysts, a higher H-to-C ratio can be obtained by either the rejection of carbon (as in coking) or the addition of hydrogen (as in hydrogenation processes). Slurry processes combine the flexibility of the carbon rejection with the high performance of the hydrogen addition processes. The origin of slurry processes is the Bergius-Pier technology (1920--1930) for the conversion of heavy oils and coal into distillates. Whereas the original Bergius-Pier technology did not use a catalyst, small amounts of inexpensive additives or finely dispersed hydrogenation catalysts can be used to increase the rates of the desired reactions. Catalysts can also inhibit coke formation by physically interfering with the coalescence of mesophase, which is the precursor of solid coke. Catalysts are used to reduce the severity of the process and to improve the quality of the products. Most of the research carried out in the past decade in the field of slurry processes has dealt with the identification of more effective and/or less expensive catalysts and the technological problems related to their use. Here the authors discuss both subjects, describing the path from the fundamental chemistry of dispersed catalytic systems to the development and initial commercialization of slurry processes.

  6. Oil & Natural Gas Technology

    Office of Scientific and Technical Information (OSTI)

    IN SITU THERMAL PROCESSING OF OIL SHALESANDS Authors: Michal Hradisky and Philip J. Smith DOE Award No.: DE-FE0001243 Reporting Period: October 1, 2009 - September 30, 2011 ...

  7. Sludge formation during heavy oil upgrading

    SciTech Connect (OSTI)

    Storm, D.A.; Decanio, S.J.; Edwards, J.C.

    1995-12-31

    A soft coke-like substance often forms in the liquid product of visbreaking and hydrocracking processes for upgrading vacuum residue of heavy crude oil. This material usually limits the severity or conversion of the process because it accumulates in downstream equipment. Although the amount of such material produced depends on the crude oil, it has not been possible to correlate its production rate to chemical characteristics of the vacuum residue in a quantitative manner In this work we show that the amount of sludge produced per unit weight of vacuum residue feed in laboratory hydrotreating experiments can be correlated with four chemical characteristic of the vacuum residue: the degree of condensed polynuclear aromaticity, the average number of alkyl-groups substituting the polynuclear aromatics, the ratio of heptane insolubles to pentane insoluble-heptane solubles, and the H/C ratio of the latter fraction. The correlation coefficient is 0.95.

  8. Heavy oil development in Canada - The need for upgrading

    SciTech Connect (OSTI)

    Quinn, P.C.

    1987-01-01

    The author first reviews Canada's petroleum reserves, then summarizes the problem facing Canada regarding dwindling supplies of conventional light and medium crude oils and briefly describes Canada's refining capability. With that background, he attempts to analyze the problems that face heavy oil producers in attempting to market their product and propose a potential solution to these problems as illustrated by Husky Oil's approach - the construction of a heavy oil upgrader. He closes by sharing his views on the future of heavy oil development and the policy issues facing our governments.

  9. Middle East oil and gas

    SciTech Connect (OSTI)

    Not Available

    1984-12-01

    The following subjects are covered in this publication: (1) position of preeminence of the Middle East; (2) history of area's oil operations for Iran, Iraq, Bahrain, Kuwait, Saudi Arabia, neutral zone, Qatar, United Arab Emirates, Oman and Egypt; (3) gas operations of Saudi Arabia, Iran, Kuwait, Qatar, Iraq and United Arab Emirates; (4) changing relationships with producing countries; (5) a new oil pricing environment; (6) refining and other industrial activities; and (7) change and progress. 10 figs., 12 tabs.

  10. Oil and Gas

    Office of Environmental Management (EM)

    RD&D Leases in the United States Oil Shale RD&D Leases in the United States This paper describes the original plans, progress and accomplishments, and future plans for nine oil shale research, development and demonstration (RD&D) projects on six existing RD&D leases awarded in 2006 and 2007 by the United States Department of the Interior, Bureau of Land Management (BLM) to Shell, Chevron, EGL (now AMSO), and OSEC (now Enefit American, respectively); as well as three pending

  11. Sixty-sixth annual report of the state oil and gas supervisor

    SciTech Connect (OSTI)

    Not Available

    1981-01-01

    This report contains tabulated oil and gas statistics compiled during 1980 in California. On-shore and off-shore oil production, gas production, reserves, drilling activity, enhanced recovery activity, unconventional heavy oil recovery, geothermal operations and financial data are reported. (DMC)

  12. Bahrain National Gas and Oil Authority | Open Energy Information

    Open Energy Info (EERE)

    Bahrain National Gas and Oil Authority Jump to: navigation, search Logo: Bahrain National Gas and Oil Authority Name: Bahrain National Gas and Oil Authority Address: 1435...

  13. Alabama Oil and Gas Board | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Board Jump to: navigation, search Logo: Alabama Oil and Gas Board Name: Alabama Oil and Gas Board Abbreviation: OGB Address: 420 Hackberry Lane Place: Tuscaloosa,...

  14. Oman Ministry of Oil and Gas | Open Energy Information

    Open Energy Info (EERE)

    of oil and gas. Prepare legislation and regulations governing oil and gas. Oversee oil and gas exploration and production activities. Establish "Petroleum Agreements" with...

  15. Reactive plasma upgrade of squalane - a heavy oil simulant

    SciTech Connect (OSTI)

    Kong, P.C.; Watkins, A.D.; Detering, B.A.; Thomas, C.P.

    1995-10-01

    U.S. light crude oil production has steadily declined over the last two decades. However, huge known heavy oil deposits in the North American continent remain largely untapped. In the past 10 years, the API gravity of crude oils has been decreasing by about 0.17% per year, and the sulfur content has been increasing by about 0.027% per year. As the API gravity of crude oil decreases, there will be an urgent need for economically viable new technologies to upgrade the heavy oil to a high API gravity feed stock for the refineries. The Idaho National Engineering Laboratory is investigating an innovative plasma process to upgrade heavy oil and refinery residuum. This paper will present some of the results and the implications of this technology for heavy oil upgrade and conversion.

  16. Reactive plasma upgrade of squalane - a heavy oil simulant

    SciTech Connect (OSTI)

    Kong, P.C.; Watkins, A.D.; Detering, B.A.

    1995-07-01

    U.S. light crude oil production has steadily declined over the last two decades. However, huge known heavy oil deposits in the North American continent remain largely untapped. In the past 10 years, the API gravity of crude oils has been decreasing by about 0.17% per year, and the sulfur content has been increasing by about 0.027% per year. As the API gravity of crude oil decreases, there will be an urgent need for economically viable new technologies to ungrade the heavy oil to a high API gravity feed stock for the refineries. The Idaho National Engineering Laboratory is investigating an innovative plasma process to upgrade heavy oil and refinery residuum. This paper will present some of the results and the implications of this technology for heavy oil upgrade and conversion.

  17. Modeling a set of heavy oil aqueous pyrolysis experiments

    SciTech Connect (OSTI)

    Thorsness, C.B.; Reynolds, J.G.

    1996-11-01

    Aqueous pyrolysis experiments, aimed at mild upgrading of heavy oil, were analyzed using various computer models. The primary focus of the analysis was the pressure history of the closed autoclave reactors obtained during the heating of the autoclave to desired reaction temperatures. The models used included a means of estimating nonideal behavior of primary components with regard to vapor liquid equilibrium. The modeling indicated that to match measured autoclave pressures, which often were well below the vapor pressure of water at a given temperature, it was necessary to incorporate water solubility in the oil phase and an activity model for the water in the oil phase which reduced its fugacity below that of pure water. Analysis also indicated that the mild to moderate upgrading of the oil which occurred in experiments that reached 400{degrees}C or more using a FE(III) 2-ethylhexanoate could be reasonably well characterized by a simple first order rate constant of 1.7xl0{sup 8} exp(-20000/T)s{sup {minus}l}. Both gas production and API gravity increase were characterized by this rate constant. Models were able to match the complete pressure history of the autoclave experiments fairly well with relatively simple equilibria models. However, a consistent lower than measured buildup in pressure at peak temperatures was noted in the model calculations. This phenomena was tentatively attributed to an increase in the amount of water entering the vapor phase caused by a change in its activity in the oil phase.

  18. Gulf Canada donor refined bitumen heavy oil upgrading process

    SciTech Connect (OSTI)

    Fisher, I.P.; Souhrada, F.; Woods, H.J.

    1982-09-01

    The method is a moderate-pressure, noncatalytic alternative which has been shown to be applicable to a wide range of bitumens and heavy oils. It offers the potential of efficiency and reliability at a low capitalized investment and operating cost. The raw distillates are separated from the bitumen or heavy oil and the vacuum residuum is blended with an efficient hydrogen donor stream containing a high proportion of substituted tetralins, and is thermally cracking in the liquid phase. The exhausted donor is recovered from the middle distillate reactor product, reactivated by fixed bed hydrogenation before being recycled to the reactor. The process can be self-sufficient in donor and is independent of the metal content of the feed. The products are blanded with the raw distillates and further hydrogenated to high quality petroleum products. While the primary hydrogen consumption is low, the reconstituted naphtha, distillate and gas oil fractions require less hydrogen than the coker liquids to achieve acceptable refinery feed quality. 1 figure, 9 tables.

  19. Co-processing of heavy oil

    SciTech Connect (OSTI)

    Khan, M.R.

    1995-12-31

    In co-processing of petroleum and coal, the petroleum fraction may serve as the {open_quotes}liquefaction solvent,{close_quotes} or hydrogen donor, and the aromatics present in the coal liquid may serve as hydrogen {open_quotes}shuttlers{close_quotes} by efficiently transferring hydrogen moieties to places where they are most deficient. The important advantages of co-processing include the following: (1) upgrading of heavy petroleum in a reaction with coal and (2) conversion of coal to synthetic crudes which could be further upgraded to a premium liquid fuel. Co-processing of coal with petroleum, heavy crudes, and residues through catalytic hydrogenation or solvent extraction have been extensively investigated. The studies were typically conducted in the temperature range of 450{degrees}-500{degrees}C under pressurized hydrogen; catalysts are generally also added for hydroconversion of the feedstocks. However, relatively little has been reported in the literature regarding co-processing of coal with heavy petroleum by simple pyrolysis. In this study, co-processing of heavy oil and coal at relatively middle conditions was conducted without the complicating influences of pressurized hydrogen or catalysts. The resulted demonstrate that there is a synergism during co-processing of petroleum and coal. This synergism enhances both the yield and quality of the liquid products. In general, liquids from co-processing the mixture contain a higher content of alkane/alkene, neutral aromatics, lower content of monophenols, and other oxygen containing compounds as compared to the liquids from coal alone. The liquid from the mixture also contains a higher content of naphthenic carbon and naphthenic rings/molecules than those from coal liquid. This suggests that the product from the mixture can be easily upgraded to a premium quality fuel.

  20. Oil/gas collector/separator for underwater oil leaks

    DOE Patents [OSTI]

    Henning, Carl D.

    1993-01-01

    An oil/gas collector/separator for recovery of oil leaking, for example, from an offshore or underwater oil well. The separator is floated over the point of the leak and tethered in place so as to receive oil/gas floating, or forced under pressure, toward the water surface from either a broken or leaking oil well casing, line, or sunken ship. The separator is provided with a downwardly extending skirt to contain the oil/gas which floats or is forced upward into a dome wherein the gas is separated from the oil/water, with the gas being flared (burned) at the top of the dome, and the oil is separated from water and pumped to a point of use. Since the density of oil is less than that of water it can be easily separated from any water entering the dome.

  1. Oil & Gas Technology Center | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Global Research Oil & Gas Technology Center Click to email this to a friend (Opens in new ... GE Global Research Oil & Gas Technology Center Mark Little, SVP and chief technology ...

  2. Use of hydrogen-free carbon monoxide with steam in recovery of heavy oil at low temperatures

    SciTech Connect (OSTI)

    Hyne, J. B.; Tyrer, J. D.

    1984-12-11

    A process for recovering oil from a subterranean heavy oil-containing reservoir is provided, wherein steam and carbon monoxide are injected into the reservoir at a temperature less than about 260/sup 0/ C. At these low temperatures, the steam and hydrogen-free carbon monoxide are found to react in the reservoir, by the water gas reaction, to form carbon dioxide and hydrogen. These products both have upgrading effects on the heavy oil, enhancing its quality and producibility. At the low temperatures of the process, gasification and polymerization of the heavy oil are minimized.

  3. Heavy oil and tar sands recovery and upgrading. International technology

    SciTech Connect (OSTI)

    Schumacher, M.M.

    1982-01-01

    This work provides an in-depth assessment of international technology for the recovery and upgrading of heavy crude oil and tar sands. The technologies included are currently in use, under development, or planned; emphasis is placed on post-1978 activities. The heavy oil technologies and processes considered include methods relating to the exploitation of heavy oil reservoirs, such as production from underground workings, all types of improved or enhanced recovery, subsurface extraction, and well rate stimulation. The tar sands section includes sizing the resource base and reviewing and evaluating past, present, and planned research and field developments on processes for mining, producing, extracting, and upgrading very heavy oils recovered from tar sands, e.g., bitumen recovery from tar sands where primary production was impossible because of the oil's high viscosity. 616 references.

  4. Fire flood recovery process effects upon heavy oil properties

    SciTech Connect (OSTI)

    Reichert, C.; Fuhr, B.; Sawatzky, H.; Lefleur, R.; Verkoczy, B.; Soveran, D.; Jha, K.

    1988-06-01

    The steady decline in proven conventional oil deposits world wide has increased the emphasis on the use of heavy oil and bitumen. Most of the heavy oil and oil sand deposits share the common problem of providing very little or no primary production. They require a reduction in viscosity of the oil to make it flow. The oil in place and the reservoir characteristics are generally studied carefully to determine the design of the recovery process most applicable to the deposit and to evaluate its potential. Many of these same characteristics are also used to evaluate the oil with respect to upgrading, refining and final usage in the form of products. A variety of processes have been developed most of which utilize heat either in the form of steam or combustion to mobolize the oil in the reservoir. These processes vary considerably from rather mild conditions for steam stimulation to quite severe for combustion recovery. Figure 1 shows a typical schematic of an insitu combustion process. Many variations of forward combustion are used in the field to produce oil. Depending upon the severity of the recovery process in the recovered oil may be similar to the oil in the deposit or may be highly modified (oxidized, polymerized or upgraded). A memorandum of Understanding was signed by the Governments of the United States of America, Canada and the Provinces of Saskatchewan and Alberta to study different aspects of the problems related to the recovery of oil from heavy oil and sand deposits. One phase of the study is to determine the effects of different methods of in-situ recovery on the composition of recovered bitumen and heavy oils. This paper describes the findings from a study of fireflood process in a heavy oil deposit located in the Cummings formation of the Eyehill Field in Saskatchewan, Canada.

  5. Heavy rains hamper Louisiana gas line

    SciTech Connect (OSTI)

    Horner, C.

    1983-06-01

    Despite heavy rains and flooding a 36-mile gas pipeline loop for Transcontinental Gas Pipe Line Corp. was completed from north of Starks (at the end of Transco's south Louisiana lateral) to the Lake Charles area. Somastic-coated, 42-in. grade X-60 pipe comprises 90% of the route. The contract included multiple 30-42 in. fabrications, installation of six 42-in. gate valves, and expansion of the Gillis compressor station.

  6. Imported resources - gas/oil

    SciTech Connect (OSTI)

    Jakob, K.

    1995-12-01

    The goal of this presentation is to provide information on issues of crude oil and natural gas supply at a conference addressing the problems of energy in Eastern and Central Europe. Although this can inevitably be performed through the {open_quotes}binoculars{close_quotes} of the petroleum sector of my country, I will try to present the issues and challenges that are thought to be characteristic in general for the region.

  7. Characterization of heavy oil by capillary supercritical fluid chromatography

    SciTech Connect (OSTI)

    Fuhr, B.J.; Holloway, L.R.; Reichert, C.

    1988-06-01

    The characterization of heavy oils and bitumen produced by thermal recovery methods may aid in bringing about the following benefits: improved recovery methods, promotion of upgrading in the reservoir, improved emulsion treatment and optimized use of diluent for transportation. Because of the high proportion of nonvolatile compounds in heavy oils, gas chromatography (GC) is not particularly useful for characterization purposes. High performance liquid chromatography, while capable of analyzing a larger proportion of the nonvolatiles, possesses considerably less resolution than GC. By utilizing mobile phases in their supercritical region it is possible to study compounds that cannot be vaporized for GC analysis, yet still attain the resolution approaching that of GC. Another advantage of supercritical fluid chromatography (SFC) with the commonly used mobile phase CO/sub 2/, is the ability to employ the flame ionization detector (FID) which provides a uniform response over a wide range of compound types. SFC methods used on packed columns are excellent for low resolution separations into hydrocarbon group types and can produce data in about 5 to 15 min. A number of workers have described the use of packed silica columns for the separation and quantitation of saturate and aromatic component types in gasolines and middle distillate fuels, and of saturates, aromatics and polars in high boiling residues. In these studies the mobile phase was CO/sub 2/ and the detector was the FID. Campbell and Lee reported a semi-preparative SFC method using a packed, amino-modified silica column for the separation of aromatics according to the number of rings in a coal tar and a solved refined coal heavy distillate.

  8. Dynacracking process first commerical application for upgrading heavy oils

    SciTech Connect (OSTI)

    Dawson, F.N. Jr.

    1981-01-01

    The Dynacracking process developed by Hydrocarbon Research, Inc., is a non-catalytic process capable of upgrading heavy oil whose sulfur, metal, and carbon contents may be high. It converts residual stocks to distillates with high naphtha yields, and to synthetic fuel gas of high quality (700-800 Btu/ft/sup 3/). It has esentially no air polution emissions and requires a relatively small amount of water and utilities. The process generates sufficient heat internally such that, except for start-up, no boilers, furnaces, or external heaters are required to operate the plant. Several aspects of the process are discussed: chemistry, hardware, feedstock, flexibility in the product mix, product quality, and economics.

  9. EXPERIMENTAL AND THEORETICAL DETERMINATION OF HEAVY OIL VISCOSITY...

    Office of Scientific and Technical Information (OSTI)

    EXPERIMENTAL AND THEORETICAL DETERMINATION OF HEAVY OIL VISCOSITY UNDER RESERVOIR CONDITIONS FINAL PROGRESS REPORT PERIOD: OCT 1999-MAY 2003 CONTRACT NUMBER: DE-FG26-99FT40615 ...

  10. Heavy and Thermal Oil Recovery Production Mechanisms, SUPRI TR-127

    SciTech Connect (OSTI)

    Kovscek, Anthony R.; Brigham, William E.; Castanier, Louis M.

    2001-09-07

    The program spans a spectrum of topics and is divided into five categories: (i) multiphase flow and rock properties, (ii) hot fluid injection, (iii) primary heavy-oil production, (iv) reservoir definition, and (v) in-situ combustion.

  11. 05663_AlaskaHeavyOil | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DE-NT0005663 Goal The goal of this project is to improve recovery of Alaskan North Slope (ANS) heavy oil resources in the Ugnu formation by improving our understanding of the ...

  12. 05663_AlaskaHeavyOil | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fluid and Rock Property Controls On Production and Seismic Monitoring Alaska Heavy Oils Last Reviewed 12/20/2012 DE-NT0005663 Goal The goal of this project is to improve recovery of Alaskan North Slope (ANS) heavy oil resources in the Ugnu formation by improving our understanding of the formation's vertical and lateral heterogeneities via core evaluation, evaluating possible recovery processes, and employing geophysical monitoring to assess production and modify production operations. Performers

  13. Process for converting heavy oil deposited on coal to distillable oil in a low severity process

    DOE Patents [OSTI]

    Ignasiak, Teresa; Strausz, Otto; Ignasiak, Boleslaw; Janiak, Jerzy; Pawlak, Wanda; Szymocha, Kazimierz; Turak, Ali A.

    1994-01-01

    A process for removing oil from coal fines that have been agglomerated or blended with heavy oil comprises the steps of heating the coal fines to temperatures over 350.degree. C. up to 450.degree. C. in an inert atmosphere, such as steam or nitrogen, to convert some of the heavy oil to lighter, and distilling and collecting the lighter oils. The pressure at which the process is carried out can be from atmospheric to 100 atmospheres. A hydrogen donor can be added to the oil prior to deposition on the coal surface to increase the yield of distillable oil.

  14. Oil and Gas Lease Equipment and Operating Costs 1994 Through...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Natural Gas > Publications > Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009 Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009 Released: September ...

  15. Geothermal Power/Oil & Gas Coproduction Opportunity

    SciTech Connect (OSTI)

    DOE

    2012-02-01

    Coproduced geothermal resources can deliver near-term energy savings, diminish greenhouse gas emissions, extend the economic life of oil and gas fields, and profitably utilize oil and gas field infrastructure. This two-pager provides an overview of geothermal coproduced resources.

  16. Oil and Gas Company Oil and Gas Company Address Place Zip Website

    Open Energy Info (EERE)

    Oil and Gas Company Address Place Zip Website Abu Dhabi National Oil Company Abu Dhabi National Oil Company Abu http www adnoc ae default aspx Al Furat Petroleum Company Al Furat...

  17. Development Practices for Optimized MEOR in Shallow Heavy Oil Reservoirs

    SciTech Connect (OSTI)

    Shari Dunn-Norman

    2006-09-30

    The goal of this project is to demonstrate an economically viable and sustainable method of producing shallow heavy oil reserves in southwest Missouri and southeast Kansas using a combination of microbial enhanced oil recovery (MEOR) and hydraulic fracturing of vertical wells.

  18. Heavy oil and tar sands recovery and upgrading: international technology

    SciTech Connect (OSTI)

    Schumacher, M.M.

    1982-01-01

    This book provides an in-depth assessment of international technology for the recovery and upgrading of heavy crude oil and tar sands. The technologies included are currently in use, under development, or planned; emphasis is placed on post-1978 activities. The heavy oil technologies and processes considered in Part I include methods relating to the exploitation of heavy oil reservoirs, such as production from undergorun workings, all types of improved or enhanced recovery, subsurface extraction, and well rate stimulation. Furthermore, even though heavy crudes are understood to include only those liquid or semiliquid hydrocarbons with a gravity of 20/sup 0/API or less, technology applied to lighter crude oils with in situ viscosities of the same order of magnitude as some US heavy oils is also included. The scope of the tar sands section (Part II) includes sizing the resource base and reviewing and evaluatin past, present, and planned research and field developments on processes for mining, producing, extracting, and upgrading very heavy oils recovered from tar sands, e.g., bitumen recovery from tar sands where primary production was impossible because of the oil's high viscosity. On the production side, very heavy oil is defined as having a gravity less than 10/sup 0/ to 12/sup 0/API and greater than 100,000-centipoise viscosity at 50/sup 0/F. On the upgrading side, hydrocarbons whose characteristics dictated additional processing prior to conventional refining into salable products (1050+/sup 0/ material) were included, regardless of origin, in order to encompass all pertinent upgrading technologies.

  19. Heavy oil reservoirs recoverable by thermal technology. Annual report

    SciTech Connect (OSTI)

    Kujawa, P.

    1981-02-01

    The purpose of this study was to compile data on reservoirs that contain heavy oil in the 8 to 25/sup 0/ API gravity range, contain at least ten million barrels of oil currently in place, and are non-carbonate in lithology. The reservoirs within these constraints were then analyzed in light of applicable recovery technology, either steam-drive or in situ combustion, and then ranked hierarchically as candidate reservoirs. The study is presented in three volumes. Volume I presents the project background and approach, the screening analysis, ranking criteria, and listing of candidate reservoirs. The economic and environmental aspects of heavy oil recovery are included in appendices to this volume. This study provides an extensive basis for heavy oil development, but should be extended to include carbonate reservoirs and tar sands. It is imperative to look at heavy oil reservoirs and projects on an individual basis; it was discovered that operators, and industrial and government analysts will lump heavy oil reservoirs as poor producers, however, it was found that upon detailed analysis, a large number, so categorized, were producing very well. A study also should be conducted on abandoned reservoirs. To utilize heavy oil, refiners will have to add various unit operations to their processes, such as hydrotreaters and hydrodesulfurizers and will require, in most cases, a lighter blending stock. A big problem in producing heavy oil is that of regulation; specifically, it was found that the regulatory constraints are so fluid and changing that one cannot settle on a favorable recovery and production plan with enough confidence in the regulatory requirements to commit capital to the project.

  20. State Oil and Gas Board State Oil and Gas Board Address Place...

    Open Energy Info (EERE)

    Suite Arizona http www azogcc az gov Arkansas Oil and Gas Commission Arkansas Oil and Gas Commission Natural Resources Dr Ste Arkansas http www aogc state ar us JDesignerPro...

  1. Process for demetallizing and desulfurizing heavy crude oil

    SciTech Connect (OSTI)

    Brown, R.E.; Hogan, R.J.; Combs, D.M.; Kukes, S.G.

    1989-12-05

    This patent describes a process for producing a synthetic crude oil of improved properties by desulfurizing, denitrogenating and demetallizing a heavy crude oil feed stock. The feed stock being a crude oil having an average boiling point at least as high as 500{degrees} F., an API gravity at 60{degrees} F. of less than 20, and containing at least about 1 weight percent sulfur.

  2. Lime addition to heavy crude oils prior to coking

    SciTech Connect (OSTI)

    Kessick, M. A.; George, Z. M.; Schneider, L. G.

    1985-06-04

    The sulphur emissive capability, on combustion, of coke which is formed during upgrading of sulphur-containing heavy crude oils, including oil sands bitumen, or residua is decreased by the addition of slaked lime or calcium oxide to the heavy crude oil prior to coking. The presence of the slaked lime or calcium oxide leads to an increased yield of liquid distillates at coking temperatures of about 450/sup 0/ to about 500/sup 0/ C. Ash remaining after combustion of the coke may be leached to recover nickel and vanadium values therefrom.

  3. Canada's heavy oil, bitumen upgrading activity is growing

    SciTech Connect (OSTI)

    Corbett, R.A.

    1989-06-26

    Heavy oil and bitumen upgrading activity in Canada is surging with the recent start-up of two new upgraders and with plans to build others. These new upgraders make use of modern hydrocracking technology. Articles in this special report on upgrading focus on Canada's oil and bitumen reserves, the promising technologies that upgrade them, and present details of some of the current upgrader projects. This article covers the following areas: Canada's heavy oils; Upgrading expands; Upgrading technologies; Test results; Regional upgraders; High-quality light product.

  4. Canadian oilsands, heavy oil adjusting to tough economics

    SciTech Connect (OSTI)

    Not Available

    1994-07-11

    Canadian oilsands and heavy oil operators are using operational upgrades and substantial research outlays as key weapons against an economic squeeze brought about largely by volatile oil prices. The Canadian Oilsands Network for Research and Development (Conrad) was formed late last year to coordinate nonproprietary research on oilsands technology among industry, government, and academic centers. The Alberta Oilsands Technology and Research Authority (Aostra), now part of Alberta's energy department, also is active with a number of industry partners in oilsands and heavy oil research. Aostra has made significant gains in demonstration projects. The paper discusses upgrader problems, key ingredients to improving operations and development of new technology, syncrude operations, cost, environmental upgrading, Imperials' heavy oil operation at Cold Lake, Shell's operation at Peace River and Amoco operations in Canada.

  5. Upgrading heavy oils by solvent dissolution and ultrafiltration

    SciTech Connect (OSTI)

    Osterhuber, E.J.

    1989-01-10

    A method is described for the separation of a heavy oil diluting the heavy oil with a solvent which is completely miscible with the heavy oil in an amount sufficient to completely dissolve the oil so as to produce an ultrafiltration feed; contacting the ultrafiltration feed with a first side of a continuous generally unswelled organic membrane selected from the group consisting of those comprising cellulose or polyvinylidine fluoride at a pressure between about 750 kPa and about 1500 kPa and at a temperature between 20/sup 0/C. and about 125/sup 0/C.; recovering a permeate fraction enriched in aromatic and saturated hydrocarbons from a second side of the membrane, and recovering a retentate fraction enriched in polar and metal-containing hydrocarbons from the first side of the membrane.

  6. US crude oil, natural gas, and natural gas liquids reserves

    SciTech Connect (OSTI)

    Not Available

    1990-10-05

    This report presents estimates of proved reserves of crude oil, natural gas, and natural gas liquids as of December 31, 1989, and production volumes for the year 1989 for the total United States and for selected states and state sub-divisions. Estimates are presented for the following four categories of natural gas: total gas (wet after lease separation), its two major components (nonassociated and associated-dissolved gas), and total dry gas (wet gas adjusted for the removal of liquids at natural gas processing plants). In addition, two components of natural gas liquids, lease condensate and natural gas plant liquids, have their reserves and production reported separately. Also included is information on indicated additional crude oil reserves and crude oil, natural gas, and lease condensate reserves in nonproducing reservoirs. 28 refs., 9 figs., 15 tabs.

  7. A novel process for upgrading heavy oil emulsions

    SciTech Connect (OSTI)

    Ng, F.T.T.; Rintjema, R.T.

    1994-12-31

    Canada has extensive reserves of high sulfur heavy oils. These heavy oils are recovered primarily by steam injection techniques. As a result, the heavy oils are obtained as emulsions at well-heads. The heavy oils, being high in sulfur and metals, and low in hydrogen to carbon atomic ratio, require upgrading such as desulfurization and hydrocracking before it can be used in conventional refineries. Conventional emulsion treatment and desulfurization technology require multistage processing. Thus, alternative technologies for processing heavy oil emulsions would be attractive. The authors have recently developed a novel single stage process for upgrading emulsions via activation of water to provide hydrogen in situ for catalytic desulfurization and hydrocracking. Current work is focused on the desulfurization aspect of upgrading, using benzothiophene as the model sulfur compound and molybdic acid as the catalyst. At 340 C and a CO loading pressure of 600 psi, up to 86% sulfur removal was obtained. As well, in situ generated H{sub 2} was found to be more active than externally supplied molecular H{sub 2}. A likely pathway for desulfurization of benzothiophene was via the initial hydrogenation of benzothiophene to dihydrobenzothiophene followed by hydrogenolysis to give ethylbenzene and H{sub 2}S.

  8. Ecuador: Accessing oil and gas opportunities

    SciTech Connect (OSTI)

    Lopez, P.

    1996-12-31

    Developments in the oil and natural gas production industries in Ecuador and on the goal of attracting private investment into the formerly state-dominated industries are discussed. The need to improve the efficiency of oil and gas extraction in order to remain competitive is described.

  9. Arctic Oil and Natural Gas Potential

    Reports and Publications (EIA)

    2009-01-01

    This paper examines the discovered and undiscovered Arctic oil and natural gas resource base with respect to their location and concentration. The paper also discusses the cost and impediments to developing Arctic oil and natural gas resources, including those issues associated with environmental habitats and political boundaries.

  10. Upgrading heavy hydrocarbon oils using sodium hypochlorite

    SciTech Connect (OSTI)

    Rankel, L.A.

    1986-07-22

    A process is described for demetallizing a residual hydrocarbon fraction comprising: (a) contacting the hydrocarbon fraction with an aqueous solution of a hypochlorite salt; (b) separating the mixture into an aqueous phase and an oil phase; (c) contacting the oil phase with a deasphalting solvent and (d) obtaining by separation a product comprising a demetallized oil fraction suitable for use as a feedstock for catalytic processing.

  11. A technical and economic assessment of petroleum, heavy oil, shale oil and coal liquid refining

    SciTech Connect (OSTI)

    Sikonia, J.G.; Shah, B.R.; Ulowetz, M.A.

    1983-11-01

    Decreasing availability of conventional crude oil will result in the utilization of alternative raw materials for the production of transportation fuels. Based on currently available processes and as a result of detailed pilot plant studies, the differences in the technical and economic aspects of refining alternative feedstocks of heavy oil, coal liquids and shale oil have indicated that heavy, hydrogen-deficient materials require more complex and costly upgrading techniques. Compared to the base case of Arabian Light crude oil, the Mexican Maya heavy oil is worth about $4.35/B less, the coal liquid about $2.38/B less and the shale oil about $5.98/B less. All of these alternative fuels can be upgraded into high quality transportation fuels.

  12. Form:International Oil and Gas Board | Open Energy Information

    Open Energy Info (EERE)

    International Oil and Gas Board Jump to: navigation, search International Oil and Gas Board This is the "International Oil and Gas Board" form. To create a page with this form,...

  13. Form:Federal Oil and Gas Regulation | Open Energy Information

    Open Energy Info (EERE)

    Federal Oil and Gas Regulation Jump to: navigation, search Federal Oil and Gas Regulation This is the "Federal Oil and Gas Regulation" form. To create a page with this form, enter...

  14. Form:Oil and Gas Company | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Company Jump to: navigation, search Oil and Gas Company This is the "Oil and Gas Company" form. To create a page with this form, enter the page name below; if a page...

  15. Form:Federal Oil and Gas Statute | Open Energy Information

    Open Energy Info (EERE)

    Federal Oil and Gas Statute Jump to: navigation, search Federal Oil and Gas Statute This is the "Federal Oil and Gas Statute" form. To create a page with this form, enter the page...

  16. Form:State Oil and Gas Board | Open Energy Information

    Open Energy Info (EERE)

    State Oil and Gas Board Jump to: navigation, search State Oil and Gas Board This is the "State Oil and Gas Board" form. To create a page with this form, enter the page name below;...

  17. About the Oil and Gas Field Code Master List

    U.S. Energy Information Administration (EIA) Indexed Site

    About the Oil and Gas Field Code Master List 1 April 30, 2012 About the Oil and Gas Field Code Master List The U.S. Energy Information Administration's (EIA) Oil and Gas Field Code ...

  18. Power Plays: Geothermal Energy in Oil and Gas Fields | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Power Plays: Geothermal Energy in Oil and Gas Fields Power Plays: Geothermal Energy in Oil and Gas Fields Power Plays: Geothermal Energy in Oil and Gas Fields April 25, 2016 9:00AM ...

  19. Oklahoma Corporate Commission Oil and Gas | Open Energy Information

    Open Energy Info (EERE)

    Corporate Commission Oil and Gas Jump to: navigation, search Name: Oklahoma Corporate Commission Oil and Gas Place: Oklahoma Zip: 73152-2000 Website: www.occeweb.comogoghome.htm...

  20. Oregon Oil, Gas, and Geothermal | Open Energy Information

    Open Energy Info (EERE)

    Oil, Gas, and Geothermal Jump to: navigation, search Name: Oregon Oil, Gas, and Geothermal Address: 229 Broadalbin St. SW Place: Oregon Zip: 97321 Website: www.oregongeology.org...

  1. Arizona Oil and Gas Commission | Open Energy Information

    Open Energy Info (EERE)

    Commission Jump to: navigation, search Logo: Arizona Oil and Gas Commission Name: Arizona Oil and Gas Commission Address: 416 W. Congress Street, Suite 100 Place: Arizona Zip:...

  2. Mississippi State Oil and Gas Board | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Board Jump to: navigation, search Name: Mississippi State Oil and Gas Board Address: 500 Greymont Ave., Suite E Place: Mississippi Zip: 39202-3446 Website:...

  3. Montana Board of Oil and Gas Conservation | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Conservation Jump to: navigation, search Name: Montana Board of Oil and Gas Conservation Address: 2535 St. Johns Avenue Place: Montana Zip: 59102 Website:...

  4. Wyoming Oil and Gas Conservation Commission | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Conservation Commission Jump to: navigation, search Name: Wyoming Oil and Gas Conservation Commission Address: 2211 King Blvd Place: Wyoming Zip: 82602 Website:...

  5. Railroad Commission of Texas, Oil and Gas Division | Open Energy...

    Open Energy Info (EERE)

    Texas, Oil and Gas Division Jump to: navigation, search Name: Texas Railroad Commission, Oil and Gas Division Address: 1701 N. Congress Place: Texas Zip: 78711-2967 Website:...

  6. Virginia Division of Oil and Gas | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Jump to: navigation, search Name: Virginia Division of Oil and Gas Address: 1100 Bank Street Place: Virginia Zip: 23219 Website: www.dmme.virginia.govdivision...

  7. Kentucky DNR Oil and Gas Division | Open Energy Information

    Open Energy Info (EERE)

    DNR Oil and Gas Division Jump to: navigation, search Name: Kentucky DNR Oil and Gas Division Address: 1025 Capital Center Drive Place: Kentucky Zip: 40601 Website:...

  8. California Department of Conservation, Division of Oil, Gas,...

    Open Energy Info (EERE)

    Conservation, Division of Oil, Gas, and Geothermal Resources Jump to: navigation, search Name: California Department of Conservation, Division of Oil, Gas, and Geothermal Resources...

  9. Oil & Natural Gas Technology Temporal Characterization of Hydrates...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oil & Natural Gas Technology Temporal Characterization of Hydrates System Dynamics ... the northern GOM (http:www.boem.govOil-and-Gas-Energy-ProgramMapping- and-Data...

  10. Construction progresses at GE's Oil & Gas Technology Center ...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the Oil & Gas Technology Center in Oklahoma City Click to email this to a friend ... the Oil & Gas Technology Center in Oklahoma City Construction is well underway on ...

  11. Illinois DNR oil and gas division | Open Energy Information

    Open Energy Info (EERE)

    is the regulatory authority in Illinois for permitting, drilling, operating, and plugging oil and gas production wells. The Division implements the Illinois Oil and Gas Act and...

  12. West Virginia Office of Oil and Gas | Open Energy Information

    Open Energy Info (EERE)

    monitoring and regulating all actions related to the exploration, drilling, storage and production of oil and natural gas. References "West Virginia Office of Oil and Gas"...

  13. Alaska Oil and Gas Conservation Commission | Open Energy Information

    Open Energy Info (EERE)

    The AOGCC website has Alaska state oil and gas data related to monthly drilling and production reports, oil and gas databases, well history, and well information, along with...

  14. Category:Oil and Gas | Open Energy Information

    Open Energy Info (EERE)

    search This category includes companies and information related to oil (petroleum) or natural gas. Pages in category "Oil and Gas" The following 110 pages are in this category,...

  15. Providential Energy Corp formerly Providential Oil Gas Inc |...

    Open Energy Info (EERE)

    (formerly Providential Oil & Gas Inc) Place: California Sector: Hydro Product: Focused on natural gas and crude oil; expanding into hydropower, fuel cells, and ethanol. References:...

  16. Arkansas Oil and Gas Commission | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Commission Jump to: navigation, search Name: Arkansas Oil and Gas Commission Address: 301 Natural Resources Dr. Ste 102 Place: Arkansas Zip: 72205 Website:...

  17. Oil and Gas Announcements Archive | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oil and Gas Announcements Archive The December, 2015 Issue of the Methane Hydrate ... that Utica Shale could hold far more natural gas and oil than previously estimated. ...

  18. Oil and Gas Technical Assistance Capabilities Forum | Department...

    Broader source: Energy.gov (indexed) [DOE]

    DOE's National Energy Technology Laboratory (NETL) Oil and Gas program and overall capabilities related to program management, system analysis, and applied research in oil and gas. ...

  19. Fact Sheet: Gas Prices and Oil Consumption Would Increase Without...

    Energy Savers [EERE]

    Gas Prices and Oil Consumption Would Increase Without Biofuels Fact Sheet: Gas Prices and Oil Consumption Would Increase Without Biofuels Secretary of Energy Samuel W. Bodman and ...

  20. Secretary Bodman Addresses Turkmenistan Industrial Oil and Gas...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Turkmenistan Industrial Oil and Gas Exhibition Secretary Bodman Addresses Turkmenistan Industrial Oil and Gas Exhibition November 16, 2007 - 4:31pm Addthis Holds Bilateral ...

  1. SECURING OIL AND NATURAL GAS INFRASTRUCTURES IN THE NEW ECONOMY...

    Office of Environmental Management (EM)

    SECURING OIL AND NATURAL GAS INFRASTRUCTURES IN THE NEW ECONOMY SECURING OIL AND NATURAL GAS INFRASTRUCTURES IN THE NEW ECONOMY Based on the finding of a growing potential ...

  2. Conventional Energy (Oil, Gas, and Coal) Forum & Associated Vertical...

    Office of Environmental Management (EM)

    CONVENTIONAL ENERGY (OIL, GAS & COAL) FORUM & ASSOCIATED VERTICAL BUSINESS DEVELOPMENT ... South, Las Vegas, NV 89119 The dynamic world of conventional energy (focusing on oil, gas ...

  3. Hydrofracturing for Gas Oil and Geopolitical Advantage. (Conference...

    Office of Scientific and Technical Information (OSTI)

    Hydrofracturing for Gas Oil and Geopolitical Advantage. Citation Details In-Document Search Title: Hydrofracturing for Gas Oil and Geopolitical Advantage. Authors: Brady, Patrick...

  4. International Oil and Gas Board International Oil and Gas Board...

    Open Energy Info (EERE)

    Petroleum Company Syrian Petroleum Company Damascus Syria Syria http www spc sy com en production activities1 en php Yemen Ministry of Oil and Minerals Yemen Ministry of Oil and...

  5. Field development options for a waterflooded heavy-oil reservoir

    SciTech Connect (OSTI)

    Kasraie, M. ); Sammon, P.H. ); Jespersen, P.J. )

    1993-09-01

    Battrum Unit 4 is a moderately heavy-oil reservoir in Saskatchewan producing under waterflood from a thin sand. This paper describes a history match of previous field behavior and systematically analyzes through the use of numerical simulation the potential benefits to production of further waterflooding (with and without infill drilling), steamflooding, and horizontal drilling. It is found that the remaining oil recovery potential of a steamflood with horizontal well is significantly higher than that of any of the waterflood options.

  6. Oil- and gas-supply modeling

    SciTech Connect (OSTI)

    Gass, S.I.

    1982-05-01

    The symposium on Oil and Gas Supply Modeling, held at the Department of Commerce, Washington, DC (June 18-20, 1980), was funded by the Energy Information Administration of the Department of Energy and co-sponsored by the National Bureau of Standards' Operations Research Division. The symposium was organized to be a forum in which the theoretical and applied state-of-the-art of oil and gas supply models could be presented and discussed. Speakers addressed the following areas: the realities of oil and gas supply, prediction of oil and gas production, problems in oil and gas modeling, resource appraisal procedures, forecasting field size and production, investment and production strategies, estimating cost and production schedules for undiscovered fields, production regulations, resource data, sensitivity analysis of forecasts, econometric analysis of resource depletion, oil and gas finding rates, and various models of oil and gas supply. This volume documents the proceedings (papers and discussion) of the symposium. Separate abstracts have been prepared for individual papers for inclusion in the Energy Data Base.

  7. Nuclear-energy application studied as source of injection steam for heavy-oil recovery

    SciTech Connect (OSTI)

    Perrett, R.J.; Gledhill, P.R.; Dawson, P.; Stephenson, D.J.

    1981-08-03

    This study into the feasibility of adapting a well-proven nuclear reactor as a centralized source of injection steam for the recovery of heavy oil has shown that the reactor modifications are practicable and well within the bounds of current technology. The gas-cooled reactor is capable of meeting the highest steam supply pressure requirement and it possesses a high degree of inherent safety. The injection of steam for the recovery of heavy oil is the most well developed of the available options. At current price levels of oil and uranium, nuclear heat can be generated at a fraction of the running costs of oil fired thermal plant. Taken over a project lifetime of 25 years for the field model used for this assessment, the improved earnings for the nuclear option could amount to as much as /10 billion. The program requirements for a typical development have been examined and the construction times for the gas reactor steam plant, the oil-field development and the upgrading plant are compatible at between five and six years. The economic advantage of steam generation by nuclear energy gives a further recovery breakthrough. It becomes possible to continue the steam drive process up to much more adverse recovery ratios of steam quantity injected for unit oil produced if nuclear energy is employed.

  8. Investigation of Multiscale and Multiphase Flow, Transport and Reaction in Heavy Oil Recovery Processes

    SciTech Connect (OSTI)

    Yortsos, Y.C.

    2001-05-29

    This report is an investigation of various multi-phase and multiscale transport and reaction processes associated with heavy oil recovery. The thrust areas of the project include the following: Internal drives, vapor-liquid flows, combustion and reaction processes, fluid displacements and the effect of instabilities and heterogeneities and the flow of fluids with yield stress. These find respective applications in foamy oils, the evolution of dissolved gas, internal steam drives, the mechanics of concurrent and countercurrent vapor-liquid flows, associated with thermal methods and steam injection, such as SAGD, the in-situ combustion, the upscaling of displacements in heterogeneous media and the flow of foams, Bingham plastics and heavy oils in porous media and the development of wormholes during cold production.

  9. Investigation of Multiscale and Multiphase Flow, Transport and Reaction in Heavy Oil Recovery Processes

    SciTech Connect (OSTI)

    Yortsos, Yanis C.

    2001-08-07

    This project is an investigation of various multi-phase and multiscale transport and reaction processes associated with heavy oil recovery. The thrust areas of the project include the following: Internal drives, vapor-liquid flows, combustion and reaction processes, fluid displacements and the effect of instabilities and heterogeneities and the flow of fluids with yield stress. These find respective applications in foamy oils, the evolution of dissolved gas, internal steam drives, the mechanics of concurrent and countercurrent vapor-liquid flows, associated with thermal methods and steam injection, such as SAGD, the in-situ combustion, the upscaling of displacements in heterogeneous media and the flow of foams, Bingham plastics and heavy oils in porous media and the development of wormholes during cold production.

  10. DOE/BNL Liquid Natural Gas Heavy Vehicle Program

    SciTech Connect (OSTI)

    James E. Wegrzyn; Wai-Lin Litzke; Michael Gurevich

    1998-08-11

    As a means of lowering greenhouse gas emissions, increasing economic growth, and reducing the dependency on imported oil, the Department of Energy and Brookhaven National Laboratory (DOE/ BNL) is promoting the substitution of liquefied natural gas (LNG) in heavy-vehicles that are currently being fueled by diesel. Heavy vehicles are defined as Class 7 and 8 trucks (> 118,000 pounds GVVV), and transit buses that have a fuel usage greater than 10,000 gallons per year and driving range of more than 300 miles. The key in making LNG market-competitive with all types of diesel fuels is in improving energy efficiency and reducing costs of LNG technologies through systems integration. This paper integrates together the three LNG technologies of: (1) production from landfills and remote well sites; (2) cryogenic fuel delivery systems; and (3) state-of-the-art storage tank and refueling facilities, with market end-use strategies. The program's goal is to develop these technologies and strategies under a ''green'' and ''clean'' strategy. This ''green'' approach reduces the net contribution of global warming gases by reducing levels of methane and carbon dioxide released by heavy vehicles usage to below recoverable amounts of natural gas from landfills and other natural resources. Clean technology refers to efficient use of energy with low environmental emissions. The objective of the program is to promote fuel competition by having LNG priced between $0.40 - $0.50 per gallon with a combined production, fuel delivery and engine systems efficiency approaching 45%. This can make LNG a viable alternative to diesel.

  11. Seismic properties of a Venezuelan heavy oil in water emulsion

    SciTech Connect (OSTI)

    Maldonado, F.; Liu, Y.; Mavko, G.; Mukerji, T.

    1996-08-01

    Several procedures for the production of low-viscosity, surfactant-stabilized, easy-transportable dispersions of heavy crude oil in water-briefly, oil in water (or o/w) emulsions - have been recently patented. Some of them propose to form the o/w emulsion in the reservoir, after the injection of a mixture of water and surfactants, increasing significantly the per well daily production. Progression of the o/w emulsion front, through the reservoir to the production wells, can be monitored in seismic planar slices with successive 3D seismic surveys (413 seismic), if enough contrast exists between the seismic velocity value of the o/w emulsion and the one of the oil in place. To facilitate the analysis of the contrast, this study presents high frequency acoustic velocity measurements performed in the laboratory. The experimental setup includes two reflectors and an ultrasonic transducer with double burst train emission. The estimated velocity precision is 0.02%. The measured samples are: a Venezuelan heavy o/w emulsion, a mixture of the same heavy oil and gasoil and a saturated sandstone core containing the o/w emulsion. Additionally, seismic velocities of the actual pore fluids - live oil and five o/w emulsion - and saturated sandstone are calculated using the above laboratory measurements, Wood`s equation, and Gassman`s and Biot`s models.

  12. FE Oil and Natural Gas News

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    oil-natural-gas-news Office of Fossil Energy Forrestal Building 1000 Independence Avenue, SW Washington, DC 20585202-586-6660 en TechLine: Newly Released Study Highlights...

  13. Oil and gas journal databook, 1987 edition

    SciTech Connect (OSTI)

    Not Available

    1987-01-01

    This book is an annual compendium of surveys and special reports reviewed by experts. The 1987 edition opens with a forward by Gene Kinney, co-publisher of the Oil and Gas Journal and includes the OGJ 400 Report, Crude Oil Assays, Worldwide Petrochemical Survey, the Midyear Forecast and Reviews, the Worldwide Gas Processing Report, the Ethylene Report, Sulfur Survey, the International Refining, Catalyst Compilation, Annual Refining Survey, Worldwide Construction Report, Pipeline Economics Report, Worldwide Production and Refining Report, the Morgan Pipeline Cost Index for Oil and Gas, the Nelson Cost Index, the Hughes Rig Count, the Smith Rig Count, the OGJ Production Report, the API Refinery Report, API Crude and Product Stocks, APU Imports of Crude and Products, and the complete Oil and Gas Journal 1986 Index of articles.

  14. 2013 Unconventional Oil and Gas Project Selections

    Broader source: Energy.gov [DOE]

    The Office of Fossil Energy’s National Energy Technology Laboratory has an unconventional oil and gas program devoted to research in this important area of energy development. The laboratory...

  15. VEBA-cracking-processes for upgrading heavy oils and refinery residues

    SciTech Connect (OSTI)

    Graeser, U.; Niemann, K.

    1983-03-01

    More than 20 different heavy oils and residues have been processed by the VEBA-Combi-Cracking and VEBA-LQ-Cracking high pressure hydrocracking processes, in a bench scale unit. Conversions up to 99 wt % of to a syncrude, consisting of naphtha middle distillate and vacuum gas oil were obtained. Conversions correlate with space velocity at a given temperature and product pattern depends upon degree of conversion. The VEBA-LQ-Cracking process produces a stable syncrude whereas the products of the VEBA-Combi process are very low in sulfur and nitrogen.

  16. Investigation of Multiscale and Multiphase Flow, Transport and Reaction in Heavy Oil Recovery Processes

    SciTech Connect (OSTI)

    Yortsos, Yanis C.

    2002-10-08

    In this report, the thrust areas include the following: Internal drives, vapor-liquid flows, combustion and reaction processes, fluid displacements and the effect of instabilities and heterogeneities and the flow of fluids with yield stress. These find respective applications in foamy oils, the evolution of dissolved gas, internal steam drives, the mechanics of concurrent and countercurrent vapor-liquid flows, associated with thermal methods and steam injection, such as SAGD, the in-situ combustion, the upscaling of displacements in heterogeneous media and the flow of foams, Bingham plastics and heavy oils in porous media and the development of wormholes during cold production.

  17. Canadian incentives for oil and gas exploration. [Applicability to USA

    SciTech Connect (OSTI)

    Not Available

    1980-04-01

    During the 1970s a number of different exploration and production incentive programs were put in place in Canada, in particular in the Province of Alberta, Canada's principal oil- and gas-producing province. The DOE/RA is evaluating Canadian incentives for oil and gas exploration, and this study is intended to provide information that will help guide DOE/RA in determining the applicability of Canadian incentive programs in US energy policy. The study describes and documents the fiscal structure in which the Canadian oil industry operates. The incentive features of pricing policy, taxation policy, and provincial royalty systems are discussed. A principal focus of the study is on one of the most important of Canada's specific incentive programs, the Alberta Exploratory Drilling Incentive Credit Program (EDICP). The study describes and evaluates the effect of the EDICP on increased oil and gas exploration activity. Similarly, the study also reviews and evaluates other specific incentive programs such as the Alberta Geophysical Incentive Program, Frontier Exploration Allowances, and various tar sand and heavy oil development incentives. Finally the study evaluates the applicability of Canadian incentives to US energy policy.

  18. Analysis of heavy oils: Method development and application to Cerro Negro heavy petroleum

    SciTech Connect (OSTI)

    Carbognani, L.; Hazos, M.; Sanchez, V. ); Green, J.A.; Green, J.B.; Grigsby, R.D.; Pearson, C.D.; Reynolds, J.W.; Shay, J.Y.; Sturm, G.P. Jr.; Thomson, J.S.; Vogh, J.W.; Vrana, R.P.; Yu, S.K.T.; Diehl, B.H.; Grizzle, P.L.; Hirsch, D.E; Hornung, K.W.; Tang, S.Y.

    1989-12-01

    On March 6, 1980, the US Department of Energy (DOE) and the Ministry of Energy and Mines of Venezuela (MEMV) entered into a joint agreement which included analysis of heavy crude oils from the Venezuelan Orinoco oil belt.The purpose of this report is to present compositional data and describe new analytical methods obtained from work on the Cerro Negro Orinoco belt crude oil since 1980. Most of the chapters focus on the methods rather than the resulting data on Cerro Negro oil, and results from other oils obtained during the verification of the method are included. In addition, published work on analysis of heavy oils, tar sand bitumens, and like materials is reviewed, and the overall state of the art in analytical methodology for heavy fossil liquids is assessed. The various phases of the work included: distillation and determination of routine'' physical/chemical properties (Chapter 1); preliminary separation of >200{degree}C distillates and the residue into acid, base, neutral, saturated hydrocarbon and neutral-aromatic concentrates (Chapter 2); further separation of acid, base, and neutral concentrates into subtypes (Chapters 3-5); and determination of the distribution of metal-containing compounds in all fractions (Chapter 6).

  19. Transformation of Resources to Reserves: Next Generation Heavy-Oil Recovery Techniques

    SciTech Connect (OSTI)

    Stanford University; Department of Energy Resources Engineering Green Earth Sciences

    2007-09-30

    This final report and technical progress report describes work performed from October 1, 2004 through September 30, 2007 for the project 'Transformation of Resources to Reserves: Next Generation Heavy Oil Recovery Techniques', DE-FC26-04NT15526. Critical year 3 activities of this project were not undertaken because of reduced funding to the DOE Oil Program despite timely submission of a continuation package and progress on year 1 and 2 subtasks. A small amount of carried-over funds were used during June-August 2007 to complete some work in the area of foamed-gas mobility control. Completion of Year 3 activities and tasks would have led to a more thorough completion of the project and attainment of project goals. This progress report serves as a summary of activities and accomplishments for years 1 and 2. Experiments, theory development, and numerical modeling were employed to elucidate heavy-oil production mechanisms that provide the technical foundations for producing efficiently the abundant, discovered heavy-oil resources of the U.S. that are not accessible with current technology and recovery techniques. Work fell into two task areas: cold production of heavy oils and thermal recovery. Despite the emerging critical importance of the waterflooding of viscous oil in cold environments, work in this area was never sanctioned under this project. It is envisioned that heavy oil production is impacted by development of an understanding of the reservoir and reservoir fluid conditions leading to so-called foamy oil behavior, i.e, heavy-oil solution gas drive. This understanding should allow primary, cold production of heavy and viscous oils to be optimized. Accordingly, we evaluated the oil-phase chemistry of crude oil samples from Venezuela that give effective production by the heavy-oil solution gas drive mechanism. Laboratory-scale experiments show that recovery correlates with asphaltene contents as well as the so-called acid number (AN) and base number (BN) of the

  20. Oil and Natural Gas Subsector Cybersecurity Capability Maturity...

    Office of Environmental Management (EM)

    Oil and Natural Gas Subsector Cybersecurity Capability Maturity Model (ONG-C2M2) Oil and Natural Gas Subsector Cybersecurity Capability Maturity Model (ONG-C2M2) Oil and Natural ...

  1. Responsible recovery of unconventional oil and gas (UOG) requires...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Responsible recovery of unconventional oil and gas (UOG) requires technologies that ensure ... Office of Oil and Natural Gas Goals One of the primary goals of FE's Office of Oil and ...

  2. Development of unconventional oil and gas (UOG) must be done...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    unconventional oil and gas (UOG) must be done in responsible ways to minimize surface ... Office of Oil and Natural Gas Goals * To reduce the amount of land and time needed for oil ...

  3. Processing of heavy oil utilizing the Aurabon process. Final report

    SciTech Connect (OSTI)

    Not Available

    1982-01-01

    This report contains estimates of the product yields and product properties from four separate, commercial-scale Aurabon heavy oil upgrading complexes capable of producing low-sulfur, hydrogen-rich products from various fractions of either a Venezuelan Boscan or a Canadian Lloydminster heavy oil feedstock. These estimates formed the basis for the development of the necessary process engineering work, including the general equipment specifications for the major equipment items included in each processing unit, required to determine cost and utilities estimates, construction labor requirements, and an estimated construction cost schedule for each of the four upgrading complexes. In addition to the above information, estimates of the yields and properties of the products produced during the upgrading of the heavy portion of the Aurabon product by both the hydrocracking and fluidized catalytic cracking processes are also included in this report. Consistent with the provisions of the executed contract for this work, those portions of the engineering work which were considered proprietary to UOP, including the heat and material balances, process flow diagrams, piping and instrument diagrams, and general equipment specifications developed for each process unit contained in the heavy oil upgrading facilities have not been included in this report. This report does, however, contain sufficient non-proprietary information to provide the reader with a general understanding of the Aurabon process and detailed information regarding the performance of the process when upgrading the two heavy oil feedstocks studied. UOP has allowed the consulting firms of Walk, Haydel and Associates of New Orleans, Louisiana and Texas Consultants, Inc. of Houston, Texas to review various portions of the engineering work developed by UOP under this contract. 1 reference, 13 figures, 22 tables.

  4. System and method for preparing near-surface heavy oil for extraction using microbial degradation

    DOE Patents [OSTI]

    Busche, Frederick D.; Rollins, John B.; Noyes, Harold J.; Bush, James G.

    2011-04-12

    A system and method for enhancing the recovery of heavy oil in an oil extraction environment by feeding nutrients to a preferred microbial species (bacteria and/or fungi). A method is described that includes the steps of: sampling and identifying microbial species that reside in the oil extraction environment; collecting fluid property data from the oil extraction environment; collecting nutrient data from the oil extraction environment; identifying a preferred microbial species from the oil extraction environment that can transform the heavy oil into a lighter oil; identifying a nutrient from the oil extraction environment that promotes a proliferation of the preferred microbial species; and introducing the nutrient into the oil extraction environment.

  5. Heavy oil upgrading via fluidized bed processing and hydrogenation processing

    SciTech Connect (OSTI)

    Dawson, F.N. Jr.

    1995-09-01

    California is the second largest crude oil producer in the lower 48 states. Nearly half of its production is heavy oil, difficult to transport and costly to refine. Given better methods of processing, production could be expanded. Likewise, huge worldwide reserves of heavy oils could be better exploited if more attractive processing methods were available. Midway Sunset crude at 11.8 API gravity, is a fairly difficult crude to process. It has about 1.5 percent sulfur, a very high nitrogen content, in the range of 0.7--0.8%, and metals of approximately 120--170 ppm, vanadium plus nickel. The authors will be reporting here results of the pilot plant testing to see whether non-catalytic fluid bed cracking technology, operated at low conversion, followed by hydrogenation would be economically attractive. Results suggest that this approach is competitive with delayed coking and with atmospheric resid desulfurization. This approach successfully combines carbon removal and hydrogen addition techniques for heavy oil upgrading. Comparative yields, product quality and economic considerations are reviewed in this study.

  6. Heavy oil upgrading for the future

    SciTech Connect (OSTI)

    Reynolds, B.E.; Johnson, D.R.; Lasher, J.S.; Hung, C. )

    1989-01-01

    The Chevron RDS Hydrotreating Process and the Gulf Resid HDS Process were pioneers in this field, beginning with the startup of the first resid desulfurization unit in 1969. The merger of Chevron Corporation with Gulf Oil Corporation resulted in a versatile new RDS Hydrotreating technology which utilizes the best features of the original Chevron and Gulf processes. Continuing improvements in the catalyst and in process configuration have greatly increased the capability of combined Chevron RDS hydrotreating to provide deeper demetalation (HDM), denitrification (HDN), Ramscarbon removal (HDR), desulfurization (HDAS), and greater cracking conversion (HCR) while processing more difficult feedstocks. future. The process is detailed by the authors.

  7. Fluvial-deltaic heavy oil reservoir, San Joaquin basin

    SciTech Connect (OSTI)

    Miller, D.D.; McPherson, J.G.; Covington, T.E.

    1989-03-01

    Unconsolidated arkosic sands deposited in a fluvial-deltaic geologic setting comprise the heavy oil (13/degree/ API gravity) reservoir at South Belridge field. The field is located along the western side of the San Joaquin basin in Kern County, California. More than 6000 closely spaced and shallow wells are the key to producing the estimated 1 billion bbl of ultimate recoverable oil production. Thousands of layered and laterally discontinuous reservoir sands produce from the Pleistocene Tulare Formation. The small scale of reservoir geometries is exploited by a high well density, required for optimal heavy oil production. Wells are typically spaced 200-500 ft (66-164 m) apart and drilled to 1000 ft (328 m) deep in the 14-mi/sup 2/ (36-km/sup 2/) producing area. Successful in-situ combustion, cyclic steaming, and steamflood projects have benefited from the shallow-depth, thick, layered sands, which exhibit excellent reservoir quality. The fundamental criterion for finding another South Belridge field is to realize the extraordinary development potential of shallow, heavy oil reservoirs, even when an unspectacular discovery well is drilled. The trap is a combination of structural and stratigraphic mechanisms plus influence from unconventional fluid-level and tar-seal traps. The depositional model is interpreted as a braid delta sequence that prograded from the nearby basin-margin highlands. A detailed fluvial-deltaic sedimentologic model establishes close correlation between depositional lithofacies, reservoir geometries, reservoir quality, and heavy oil producibility. Typical porosity is 35% and permeability is 3000 md.

  8. Pennsylvania Bureau of Oil and Gas Management | Open Energy Informatio...

    Open Energy Info (EERE)

    and the environment. The bureau develops policy and programs for the regulation of oil and gas development and production pursuant to the Oil and Gas Act, the Coal and Gas...

  9. Top 100 Oil and Gas Fields of 2009

    Gasoline and Diesel Fuel Update (EIA)

    Top 100 Oil and Gas Fields of 2009 Introduction This supplement to the Energy Information Administration's summary of U.S. Crude Oil, Natural Gas, and Natural Gas Liquids Proved ...

  10. AEO2012 Preliminary Assumptions: Oil and Gas Supply

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    3 Oil and Gas Supply Working Group Meeting Office of Petroleum, Gas, and Biofuels Analysis ... for Annual Energy Outlook 2013: Oil and Gas Working Group Overview 2 Office of ...

  11. Feasibility study of heavy oil recovery in the Appalachian, Black Warrior, Illinois, and Michigan basins

    SciTech Connect (OSTI)

    Olsen, D.K.; Rawn-Schatzinger, V.; Ramzel, E.B.

    1992-07-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production. Each report covers select areas of the United States. The Appalachian, Black Warrior, Illinois, and Michigan basins cover most of the depositional basins in the Midwest and Eastern United States. These basins produce sweet, paraffinic light oil and are considered minor heavy oil (10{degrees} to 20{degrees} API gravity or 100 to 100,000 cP viscosity) producers. Heavy oil occurs in both carbonate and sandstone reservoirs of Paleozoic Age along the perimeters of the basins in the same sediments where light oil occurs. The oil is heavy because escape of light ends, water washing of the oil, and biodegradation of the oil have occurred over million of years. The Appalachian, Black Warrior, Illinois, and Michigan basins` heavy oil fields have produced some 450,000 bbl of heavy oil of an estimated 14,000,000 bbl originally in place. The basins have been long-term, major light-oil-producing areas and are served by an extensive pipeline network connected to refineries designed to process light sweet and with few exceptions limited volumes of sour or heavy crude oils. Since the light oil is principally paraffinic, it commands a higher price than the asphaltic heavy crude oils of California. The heavy oil that is refined in the Midwest and Eastern US is imported and refined at select refineries. Imports of crude of all grades accounts for 37 to >95% of the oil refined in these areas. Because of the nature of the resource, the Appalachian, Black Warrior, Illinois and Michigan basins are not expected to become major heavy oil producing areas. The crude oil collection system will continue to degrade as light oil production declines. The demand for crude oil will increase pipeline and tanker transport of imported crude to select large refineries to meet the areas` liquid fuels needs.

  12. Feasibility study of heavy oil recovery in the Appalachian, Black Warrior, Illinois, and Michigan basins

    SciTech Connect (OSTI)

    Olsen, D.K.; Rawn-Schatzinger, V.; Ramzel, E.B.

    1992-07-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production. Each report covers select areas of the United States. The Appalachian, Black Warrior, Illinois, and Michigan basins cover most of the depositional basins in the Midwest and Eastern United States. These basins produce sweet, paraffinic light oil and are considered minor heavy oil (10{degrees} to 20{degrees} API gravity or 100 to 100,000 cP viscosity) producers. Heavy oil occurs in both carbonate and sandstone reservoirs of Paleozoic Age along the perimeters of the basins in the same sediments where light oil occurs. The oil is heavy because escape of light ends, water washing of the oil, and biodegradation of the oil have occurred over million of years. The Appalachian, Black Warrior, Illinois, and Michigan basins' heavy oil fields have produced some 450,000 bbl of heavy oil of an estimated 14,000,000 bbl originally in place. The basins have been long-term, major light-oil-producing areas and are served by an extensive pipeline network connected to refineries designed to process light sweet and with few exceptions limited volumes of sour or heavy crude oils. Since the light oil is principally paraffinic, it commands a higher price than the asphaltic heavy crude oils of California. The heavy oil that is refined in the Midwest and Eastern US is imported and refined at select refineries. Imports of crude of all grades accounts for 37 to >95% of the oil refined in these areas. Because of the nature of the resource, the Appalachian, Black Warrior, Illinois and Michigan basins are not expected to become major heavy oil producing areas. The crude oil collection system will continue to degrade as light oil production declines. The demand for crude oil will increase pipeline and tanker transport of imported crude to select large refineries to meet the areas' liquid fuels needs.

  13. Oil and gas development in East Siberia

    SciTech Connect (OSTI)

    Sagers, M.J.

    1994-03-01

    The East Siberian region, which comprises nearly 43% of Russia`s territory (including the Sakha (Yakut) republic), has substantial hydrocarbon potential that is impeded by significant logistical problems, the daunting physical environment, and technical challenges posed by the geological complexity of the region. The area`s three major oil and gas provinces are the Lena-Tunguska (with the greatest potential), Lena-Vilyuy, and Yenisey-Anabar. The paper focuses on assessment of reserves, production potential, and history, as well as joint-venture activity involving foreign capital. Foreign investment is targeting gas deposits in the Vilyuy basin and elsewhere in the Sakha republic and small oil deposits serving local markets in the Yakutsk and Noril`sk areas. Forecasts do not envisage substantial production of oil from the region before the year 2010. Future gas production levels are less predictable despite the ambitious plans to export gas from Sakha to South Korea. 14 refs., 1 fig., 1 tab.

  14. Upgrading of heavy oils by asphaltenic bottom cracking

    SciTech Connect (OSTI)

    Sudoh, j.; Shiroto, Y.; Fukui, Y.; Takeuchi, C.

    1983-03-01

    Results of the pilot plant study of the conversion of heavy petroleum residues (Khafji VR) to lighter feedstocks deasphalted oil (DAO) by a combination process involving asphaltenic bottom cracking (ABC) and solvent deasphalting (SDA) are reported. In addition to correlations between DAO and asphalt yield under various hydrotreating conditions, a mathematical model describing quantitative relationships between recycle rate of SDA asphalt and ABC in extinction and recycle operations are described. Effects of process variations on product (DAO, asphalt) quality are also discussed.

  15. Precambrian oil and gas in China

    SciTech Connect (OSTI)

    Sisheng Hao; Guangdi Liu

    1989-03-01

    Abundant Precambrian oil and gas occurring mainly in two large basins, Sichuan basin in southwestern China and Bohai Bay basin in northern China, account for a considerable portion of the reserves and production in China. The Precambrian producing formations are all carbonates. Weiyuan gas field in Sichuan basin is one of the large gas fields in China. Its gas is produced primarily from the dolomite of the Dengying Formation (Sinian System) and was generated chiefly in the algal dolomite of the same system. However, a deeper origin for the gas cannot be ruled out. Renqiu oil field in Bohai Bay basin, a buried-hill oil field, is also one of the largest oil fields in China. The oil is produced primarily from the dolomite of the Wumishan Formation of the middle-upper Proterozoic and was generated chiefly in the Oligocene Shahejie Formation. It is also possible that the oil was partly sourced by middle-upper Proterozoic rocks. In addition, many oil and gas shows have been found in the middle-upper Proterozoic of the Yanshan fold-belt at the northern margin of the Bohai Bay basin. According to an organic geochemical study, the middle-upper Proterozoic in the area has a good potential for hydrocarbon generation, and formation conditions for indigenous hydrocarbon accumulation should exist in the Bohai Bay basin and nearby Yanshan foldbelt. From the analyses of hydrocarbon generation, reservoir, cap rock, trapping, and preservation, the presentation systematically describes the petroleum geological features and hydrocarbon prospects of the Precambrian in China.

  16. Oil shale retorting with steam and produced gas

    SciTech Connect (OSTI)

    Merrill, L.S. Jr.; Wheaton, L.D.

    1991-08-20

    This patent describes a process for retorting oil shale in a vertical retort. It comprises introducing particles of oil shale into the retort, the particles of oil shale having a minimum size such that the particles are retained on a screen having openings 1/4 inch in size; contacting the particles of oil shale with hot gas to heat the particles of oil shale to a state of pyrolysis, thereby producing retort off-gas; removing the off-gas from the retort; cooling the off-gas; removing oil from the cooled off-gas; separating recycle gas from the off-gas, the recycle gas comprising steam and produced gas, the steam being present in amount, by volume, of at least 50% of the recycle gas so as to increase the yield of sand oil; and heating the recycle gas to form the hot gas.

  17. Saber's heavy oil cracking refinery project

    SciTech Connect (OSTI)

    Benefield, C.S.; Glasscock, W.L.

    1983-03-01

    Perhaps more than any other industry, petroleum refining has been subjected to the radical swings in business and political climates of the past several decades. Because of the huge investments and long lead times to construct refining facilities, stable government policies, predictable petroleum prices, secure feedstock supplies and markets, and reliable cost estimates are necessary ingredients to effectively plan new refinery projects. However, over the past ten years the political and economic climates have provided anything but these conditions. Yet, refiners have demonstrated a willingness to undertake risks by continuing to expand and modernize their refineries. The refining business -- just as most businesses -- responds to economic incentives. These incentives, when present, result in new technology and capacity additions. In the 1940's, significant technology advances were commercialized to refine higher-octane motor gasolines. Such processes as continuous catalytic cracking (Houdry Process Corporation), fluid catalytic cracking (Standard Oil Development Company), HF alkylation (UOP and Phillips Petroleum Company), and catalytic reforming (UOP) began to supply a growing gasoline market, generated from the war effort and the ever increasing numbers of automobiles on the road. The post-war economy of the 1950's and 1960's further escalated demand for refined products, products which had to meet higher performance specifications and be produced from a wider range of raw materials. The refining industry met the challenge by introducing hydro-processing technology, such as hydrocracking developed in 1960. But, the era must be characterized by the large crude processing capacity additions, required to meet demand from the rapidly expanding U.S. economy. In 1950, refining capacity was 6.2 million BPD. By 1970, capacity had grown to 11.9 million BPD, an increase of 91%.

  18. Oil & Gas Technology at Oklahoma City | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Experience efforts to safely, efficiently and reliably accelerate oil and gas ... Performance & CO2 including Enhanced Oil Recovery, Alternative Stimulation Fluids, ...

  19. oil-gas-announcements | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oil and Gas Announcements The Spring, 2016 Issue of the Methane Hydrate Newsletter Fire in ... research and emergency situations, such as oil spills and search and rescue missions. ...

  20. Water-related Issues Affecting Conventional Oil and Gas Recovery...

    Office of Scientific and Technical Information (OSTI)

    Water-related Issues Affecting Conventional Oil and Gas Recovery and Potential Oil-Shale Development in the Uinta Basin, Utah Michael Vanden Berg; Paul Anderson; Janae Wallace;...

  1. FE Oil and Natural Gas News | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    future energy supplies. May 18, 2009 DOE-Supported Publication Boosts Search for Oil, Natural Gas by Petroleum Operators A comprehensive publication detailing the oil-rich...

  2. Indiana DNR Division of Oil and Gas | Open Energy Information

    Open Energy Info (EERE)

    to professional public service through the effective administration of Indiana's oil and gas exploration and production laws. References "Indiana DNR division of Oil...

  3. EIA-914 Monthly Crude Oil, Lease Condensate, and Natural Gas...

    Gasoline and Diesel Fuel Update (EIA)

    Administration | EIA-94 Monthly Crude Oil, Lease Condensate, and Natural Gas ... June 2016 U.S. Energy Information Administration | EIA-94 Monthly Crude Oil, Lease ...

  4. Technically Recoverable Shale Oil and Shale Gas Resources:

    U.S. Energy Information Administration (EIA) Indexed Site

    | Technically Recoverable Shale Oil and Shale Gas Resources i This report was ... September 2015 U.S. Energy Information Administration | Technically Recoverable Shale Oil ...

  5. Unconventional Oil and Gas Projects Help Reduce Environmental...

    Broader source: Energy.gov (indexed) [DOE]

    Unconventional Oil and Gas Projects Help Reduce Environmental Impact of Development Since the first commercial oil well was drilled in the United States in 1859, most of the ...

  6. Alaska--State Offshore Natural Gas Withdrawals from Oil Wells...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) Alaska--State Offshore Natural Gas Withdrawals from Oil ... Release Date: 06302016 Next Release Date: 07292016 Referring Pages: Offshore Gross ...

  7. Federal Offshore--Alabama Natural Gas Withdrawals from Oil Wells...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) Federal Offshore--Alabama Natural Gas Withdrawals from Oil ... Release Date: 06302016 Next Release Date: 07292016 Referring Pages: Offshore Gross ...

  8. US--Federal Offshore Natural Gas Withdrawals from Oil Wells ...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) US--Federal Offshore Natural Gas Withdrawals from Oil Wells ... Release Date: 06302016 Next Release Date: 07292016 Referring Pages: Offshore Gross ...

  9. Texas--State Offshore Natural Gas Withdrawals from Oil Wells...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) Texas--State Offshore Natural Gas Withdrawals from Oil ... Release Date: 06302016 Next Release Date: 07292016 Referring Pages: Offshore Gross ...

  10. Louisiana--State Offshore Natural Gas Withdrawals from Oil Wells...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) Louisiana--State Offshore Natural Gas Withdrawals from Oil ... Release Date: 06302016 Next Release Date: 07292016 Referring Pages: Offshore Gross ...

  11. Federal Offshore--Texas Natural Gas Withdrawals from Oil Wells...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) Federal Offshore--Texas Natural Gas Withdrawals from Oil ... Release Date: 06302016 Next Release Date: 07292016 Referring Pages: Offshore Gross ...

  12. Heavy oil upgrading using an integrated gasification process

    SciTech Connect (OSTI)

    Quintana, M.E.; Falsetti, J.S.

    1995-12-31

    The value of abundant, low-grade heavy crude oil reserves can be enhanced by appropriate upgrade processing at the production site to yield marketable refinery feedstocks or ultimate products. One of the upgrading process sequences most commonly considered involves vacuum distillation followed by a bottoms processing step such as solvent deasphalting or coking. These schemes can be further enhanced with the addition of a gasification step to convert the unsaleable, bottom-of-the-barrel residues into useful products, such as high-purity hydrogen for hydrotreating, electrical power, steam for enhanced oil recovery and distillation, etc. This paper describes the Texaco Gasification Process and the T-STARs hydrotreating process, and their application in an integrated upgrade processing scheme in which an optimal, virtually bottomless oil utilization can be achieved. Illustrative examples of this integration are provided with comparative economic information.

  13. Venezuelan projects advance to develop world`s largest heavy oil reserves

    SciTech Connect (OSTI)

    Croft, G.; Stauffer, K.

    1996-07-08

    A number of joint venture projects at varying stages of progress promise to greatly increase Venezuela`s production of extra heavy oil. Units of Conoco, Chevron, Total, Arco, and Mobil have either signed agreements or are pursuing negotiations with affiliates of state-owned Petroleos de Venezuela SA on the development of huge reserves of 8--10{degree} gravity crude. Large heavy oil resources are present in the oil producing areas of eastern and western Venezuela, and the largest are in eastern Venezuela`s Orinoco heavy oil belt. The paper discusses the Orinoco heavy oil belt geology and several joint ventures being implemented.

  14. Liquid fuels from co-processing coal with bitumen or heavy oil: A review

    SciTech Connect (OSTI)

    Moschopedis, S.E.; Hepler, L.G.

    1987-01-01

    Coal, bitumen and heavy oil (and various pitches, resids, etc.) are similar in that they require more substantial treatment than does conventional light oil to yield useful liquid fuels. The authors provide a brief and selective review of technologies for liquefying coal, followed by consideration of co-processing coal with bitumen/heavy oil. Such co-processing may be considered as use of bitumen/heavy oil as a solvent and/or hydrogen donor in liquefaction of coal, or as the use of coal to aid upgrading bitumen/heavy oil.

  15. "Economic","Electricity","Fuel Oil","Fuel Oil(b)","Natural Gas...

    U.S. Energy Information Administration (EIA) Indexed Site

    "," ",," "," " ,,"Residual","Distillate",,"LPG and" "Economic","Electricity","Fuel Oil","Fuel Oil(b)","Natural Gas(c)","NGL(d)","Coal" "Characteristic(a)","(kWh)","(gallons)","...

  16. Oil and gas resources remaining in the Permian Basin

    SciTech Connect (OSTI)

    Not Available

    1989-01-01

    In this book the authors present a reevaluation of the oil and gas resource base remaining in existing Permian Basin reservoirs. The Permian Basin is one of the nation's premier sources of oil production, accounting for almost one quarter of the total domestic oil resource. The distribution and magnitude of oil and gas resources discovered in the basin are documented at the play and reservoir levels. Data on reservoir geology and volumetric analysis come from the oil and gas atlases published by the Bureau of Economic Geology, the Bureau's oil-reservoir data base, and NRG Associates Significant Oil and Gas Fields of the United States.

  17. Influence of uplift on oil migration: Tulare heavy oil accumulations, west side San Joaquin Valley, California

    SciTech Connect (OSTI)

    Chamberlain, E.R.; Madrid, V.M.

    1986-07-01

    Shallow (2000 ft), heavy (11/sup 0/-14/sup 0/ API) oil accumulations within the Pleistocene, nonmarine, Tulare sands along the west side of the San Joaquin Valley represent major thermal enhanced oil recovery (EOR) objectives. These low-pressure reservoirs display a variety of petrophysical characteristics indicating a complex history of oil migration resulting from uplift of the Tulare reservoirs above the regional ground-water table (RGT). In the Cymric-McKittrick area, it is possible to correlate Tulare outcrops with subsurface log data and determine the relationship between oil saturation, structural elevation, and proximity to the present RGT. The observed relationship is that economic oil saturations (S/sub 0/ = 30-75%) occur in structural lows and grade updip to reduced oil saturations (S/sub 0/ = 0-30%). The equivalent sands above the RGT exhibit formation density log-compensated neutron log (FDC/CNL) cross-over. Basinward, as the entire Tulare reservoir dips below the RGT, it exhibits characteristics of conventional reservoirs, such as high water saturations in structural lows, grading upward to increased oil saturations in structural highs. The authors present the following model to explain these observations. (1) Oil migrated into Tulare sands and originally filled all stratigraphic/structural traps below the paleo-RGT. (2) Subsequent uplift of the Tulare reservoirs above the paleo-RGT resulted in gravity drainage of original accumulations into structural lows. (3) Washing of the oils by repeated ground-water fluctuations along with biodegradation resulted in the essentially immobile Tulare heavy oil accumulations observed today.

  18. Alaska Division of Oil and Gas | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Jump to: navigation, search Name: Alaska Division of Oil and Gas Address: 550 W. 7th Ave., Suite 1100 Place: Alaska Zip: 99501 Website: dog.dnr.alaska.gov References:...

  19. Category:Federal Oil and Gas Statutes | Open Energy Information

    Open Energy Info (EERE)

    Federal Oil and Gas Statutes Jump to: navigation, search Add a new Federal Oil and Gas Statute You need to have JavaScript enabled to view the interactive timeline. Further results...

  20. WSDNR Oil and Gas Forms | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Forms Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: WSDNR Oil and Gas FormsLegal Abstract The Washington State...

  1. Category:State Oil and Gas Boards | Open Energy Information

    Open Energy Info (EERE)

    State Oil and Gas Boards Jump to: navigation, search Add a new State Oil and Gas Board Loading map... "format":"googlemaps3","type":"ROADMAP","types":"ROADMAP","SATELLITE","HYBRI...

  2. 16 TAC 3 - Oil and Gas Division | Open Energy Information

    Open Energy Info (EERE)

    - Oil and Gas Division Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: 16 TAC 3 - Oil and Gas DivisionLegal Abstract This...

  3. Louisiana DNR Oil and Gas Division | Open Energy Information

    Open Energy Info (EERE)

    Louisiana DNR Oil and Gas Division Jump to: navigation, search Name: Louisiana DNR Oil and Gas Division Address: P.O. Box 94396 Place: Louisiana Zip: 70804-9396 Website:...

  4. Category:Oil and Gas Companies | Open Energy Information

    Open Energy Info (EERE)

    Oil and Gas Companies Jump to: navigation, search Add a new Oil and Gas Company Loading map... "format":"googlemaps3","type":"ROADMAP","types":"ROADMAP","SATELLITE","HYBRID","TER...

  5. Category:International Oil and Gas Boards | Open Energy Information

    Open Energy Info (EERE)

    International Oil and Gas Boards Jump to: navigation, search Add a new International Oil and Gas Board Loading map... "format":"googlemaps3","type":"ROADMAP","types":"ROADMAP","S...

  6. North Dakota Industrial Commission, Oil and Gas Divisioin | Open...

    Open Energy Info (EERE)

    in Bismarck, North Dakota. About The Oil and Gas Division regulates the drilling and production of oil and gas in North Dakota. Our mission is to encourage and promote the...

  7. Indiana Natural Gas Withdrawals from Oil Wells (Million Cubic...

    U.S. Energy Information Administration (EIA) Indexed Site

    Withdrawals from Oil Wells (Million Cubic Feet) Year Jan Feb Mar Apr May Jun Jul Aug Sep ... Referring Pages: Natural Gas Gross Withdrawals from Oil Wells Indiana Natural Gas Gross ...

  8. Missouri Natural Gas Gross Withdrawals from Oil Wells (Million...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1991 0 ... Referring Pages: Natural Gas Gross Withdrawals from Oil Wells Missouri Natural Gas Gross ...

  9. Fact Sheet: Gas Prices and Oil Consumption Would Increase Without...

    Energy Savers [EERE]

    Gas Prices and Oil Consumption Would Increase Without Biofuels Fact Sheet: Gas Prices and Oil Consumption Would Increase Without Biofuels June 11, 2008 - 1:30pm Addthis Secretary ...

  10. Unconventional oil and gas (UOG) development and operations release...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Office of Oil and Natural Gas Goals The Administration has set a goal to reduce methane emissions from the oil and gas sector by 40-45 percent from 2012 levels by 2025. Achieving ...

  11. Oil and Natural Gas Subsector Cybersecurity Capability Maturity...

    Broader source: Energy.gov (indexed) [DOE]

    The Oil and Natural Gas Subsector Cybersecurity Capability Maturity Model (ONG-C2M2) is a ... Oil and Natural Gas Subsector C2M2 v1.1 (February 2014) (1.82 MB) More Documents & ...

  12. Oil and Natural Gas Program Commericialized Technologies and...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    natural gas and oil can remain part of the U.S. energy portfolio for decades to come. ... more than 30 years through Fossil Energy's Oil and Natural Gas Program, managed by NETL. ...

  13. Unconventional oil and gas (UOG) reservoirs present unique subsurface...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    This research focuses on technology and practices that minimize the number of wells that must be drilled for a given volume of oil or gas production. Office of Oil and Natural Gas ...

  14. First AEO2015 Oil and Gas Working Group Meeting Summary

    U.S. Energy Information Administration (EIA) Indexed Site

    GAS MARKETS TEAMS SUBJECT: First AEO2015 Oil and Gas Working Group Meeting Summary ... The shorter AEO2015 will have 6 cases - Reference case, HighLow Oil Price cases, HighLow ...

  15. Feasibility study of heavy oil recovery in the Midcontinent region (Kansas, Missouri, Oklahoma)

    SciTech Connect (OSTI)

    Olsen, D.K.; Johnson, W.I.

    1993-08-01

    This report is one of a series of publications assessing the feasibility/constraints of increasing domestic heavy oil production. Each report covers a select area of the United States. The Midcontinent (Kansas, Nssouri, Oklahoma) has produced significant oil, but contrary to early reports, the area does not contain the huge volumes of heavy oil that, along with the development of steam and in situ combustion as oil production technologies, sparked the area`s oil boom of the 1960s. Recovery of this heavy oil has proven economically unfeasible for most operators due to the geology of the formations rather than the technology applied to recover the oil. The geology of the southern Midcontinent, as well as results of field projects using thermal enhanced oil recovery (TEOR) methods to produce the heavy oil, was examined based on analysis of data from secondary sources. Analysis of the performance of these projects showed that the technology recovered additional heavy oil above what was produced from primary production from the consolidated, compartmentalized, fluvial dominated deltaic sandstone formations in the Cherokee and Forest City basins. The only projects producing significant economic and environmentally acceptable heavy oil in the Midcontinent are in higher permeability, unconsolidated or friable, thick sands such as those found in south-central Oklahoma. There are domestic heavy oil reservoirs in other sedimentary basins that are in younger formations, are less consolidated, have higher permeability and can be economically produced with current TEOR technology. Heavy oil production from the carbonates of central and wester Kansas has not been adequately tested, but oil production is anticipated to remain low. Significant expansion of Midcontinent heavy oil production is not anticipated because the economics of oil production and processing are not favorable.

  16. Colorado Oil and Gas Commission | Open Energy Information

    Open Energy Info (EERE)

    gas natural resources. Responsible development results in: The efficient exploration and production of oil and gas resources in a manner consistent with the protection of public...

  17. Colorado Oil and Gas Conservation Commission | Open Energy Information

    Open Energy Info (EERE)

    gas natural resources. Responsible development results in: The efficient exploration and production of oil and gas resources in a manner consistent with the protection of public...

  18. Oil & Natural Gas Projects Exploration and Production Technologies...

    Open Energy Info (EERE)

    & Natural Gas Projects Exploration and Production Technologies Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Oil & Natural Gas Projects Exploration...

  19. California Division of Oil, Gas, and Geothermal Resources | Open...

    Open Energy Info (EERE)

    reservoirs. Division requirements encourage wise development of California's oil, gas, and geothermal resources while protecting the environment.2 References "CDOGGR...

  20. Technically Recoverable Shale Oil and Shale Gas Resources

    U.S. Energy Information Administration (EIA) Indexed Site

    EIA/ARI World Shale Gas and Shale Oil Resource Assessment May, 17, 2013 2-1 SHALE GAS AND SHALE OIL RESOURCE ASSESSMENT METHODOLOGY INTRODUCTION This report sets forth Advanced Resources' methodology for assessing the in-place and recoverable shale gas and shale oil resources for the EIA/ARI "World Shale Gas and Shale Oil Resource Assessment." The methodology relies on geological information and reservoir properties assembled from the technical literature and data from publically

  1. Summary: U.S. Crude Oil, Natural Gas, and Natural Gas Liquids...

    Gasoline and Diesel Fuel Update (EIA)

    Summary: U.S. Crude Oil, Natural Gas, and Natural Gas Liquids Proved Reserves 2009 November 2010 U.S. Energy Information Administration Office of Oil, Gas, and Coal Supply...

  2. Specific heavy oil processing market study. Final report

    SciTech Connect (OSTI)

    Not Available

    1984-06-01

    The market potential for two not-yet-commercialized, proprietary processes for upgrading heavy oil was evaluated. Dynacracking (TM) of Hydrocarbon Research Inc. (HRI) and Aurabon of UOP Process Division (UOP), including an integrated commercial hydrotreating unit were the processes studied. The report concludes that while a large market for Heavy Oil Processing (HOP) units was originally forecast as the result of the shift to heavier crudes by US refiners under a given demand slate and refinery configuration, this market has either eroded due to massive demand shifts (both in volumetric and relative product mix terms) or largely been satisfied on an accelerated basis (due to downstream restructuring pressures) by units already constructed or under firm commitment utilizing other HOP technology. Dynacracking or Aurabon does not appear to offer the substantial economic advantage needed to replace other HOP units already committed. However, additional demands for HOP units couold arise, particularly on a regional basis, if significant additional foreign or domestic sources of heavy crude are introduced into the supply picture or the demand structure moves dramatically away from that currently foreseen by the EIA. Expected profit margins were calculated for both processes, allowing $2/barrel extra credit to the Aurabon products because of their higher quality. Both processes appear to produce about the same fraction of vacuum bottoms when processing the same crude. Dynacracking produces a higher proportion of naphtha and Aurabon produces substantially more heavy distillate. This report is not intended to serve as a basis of selecting either process for a particular installation. 10 references, 7 figures, 29 tables.

  3. Hydroconversion of heavy oil residues with sulfided additives of catalysts

    SciTech Connect (OSTI)

    Le Perchec, P.; Fixari, B.; Vrinat, M.

    1995-12-31

    Improvements in Heavy oils conversion imply sulfur compounds. For medium conversion, side polycondensations and coke production were avoided by Hydrogen diluent donors (HDD), but conversions were partially inhibited. Sulfided radical activators used in association with HDD and H{sub 2} pressure overcome this effect by preventing coke formation up to 50-60% conversion into 500{degrees}C{sup -} light fractions with unchanged quality profile. Deeper conversions require dispersed sulfided catalyst. Phosphomolybdic acid or molybdenum naphtenate have been used as soluble precursors for such treatments. The state and fitness of sulfidation depend on the nature of precursors.

  4. Slurry catalyst for hydroprocessing heavy and refractory oils

    SciTech Connect (OSTI)

    Lopez, J.; Pasek, E.A.

    1992-03-10

    This patent describes a Group VIB metal sulfide slurry catalyst for the hydroprocessing of heavy hydrocarbonaceous oil or residue prepared by a process. It comprises sulfiding a Group VIB metal, ammonia-containing compound in an aqueous phase, in the substantial absence of hydrocarbon oil, with hydrogen sulfide, at a temperature less than about 350{degrees} F, to form a presulfided product without substantial loss of ammonia; separating ammonia from the presulfided product to form a sulfided product; charging the sulfided product into a hydroprocessing reactor zone at a temperature sufficient to convert the sulfided product into an active hydroprocessing catalyst; wherein the catalyst is characterized by a pore volume in the range of 10 to 300{Angstrom} radius pore size of from about 0.1 to about 1 cc/g and a surface area of from about 20 to about 400 m{sup 2}/g.

  5. Design considerations for heavy oil in situ pilots

    SciTech Connect (OSTI)

    Peachey, B.R.; Nodwell, J.A.

    1982-01-01

    Although the primary objectives of heavy oil in situ pilots are reservoir oriented in terms of production rate and recovery efficiency, considerable development of surface engineering technology is a necessary aspect of pilot operations. Esso's basic design philosophy is to use state-of-the-art technology with onsite operator interaction to sequentially develop improvements in surface equipment and processes without comprising reservoir based research objectives. This work reviews Esso's operating experience and technical developments in pilot design at Cold Lake, Alta. The considerations which led to the design basis for the Cold Lake commercial project are examined in the areas of well layout, steam and production distribution system design, oil and water separation, and produced water treatment.

  6. A new hydrocracking catalyst for heavy oil upgrading

    SciTech Connect (OSTI)

    Itoh, T. )

    1987-04-01

    In comparison with ordinary oil, tar sands bitumen and vacuum residue contain large quantities of impurities such as asphaltene, heavy metal compounds, sulfur, and nitrogen, which are obstacles to upgrading the refining process. Therefore, these types of materials are extremely difficult to treat with existing refining technologies. In order to upgrade oil feedstocks that are of poor quality, such as tar sands bitumen, new upgrading technologies must be established. In this paper, the author discusses first, the results of catalyst screening, second, the factors of the active catalyst, and finally, the performance of a semi-industrially produced catalyst. The catalyst has high middle-distillate yield, coke plus gum (coke precursors) suppressing ability, low hydrogen consumption and mechanical strength and high temperature stability in slurry reactors.

  7. 9000 wells planned for heavy oil field. [Canada

    SciTech Connect (OSTI)

    Not Available

    1981-05-01

    Beginning in 1983, Esso Resources Canada Ltd. will begin drilling the first of an estimated 9000 directional crude bitumen wells in the tar sands at Cold Lake, Alberta, Canada, the final wells being drilled in the year 2008. The area, covering 50 sq miles of extreme E. Alberta along the Saskatchewan border, contains one of the richest deposits of heavy oil sands in Canada. The company and future partners will drill the bitumen wells directionally into the shallow clearwater formation, which can be reached at approx. 100 m (330 ft). The formation contains an estimated 80 billion bbl of crude bitumen at a rate of 60,000 bpd for 25 yr. This volume of crude will be refined in an upgrading plant to 140,000 bpd of synthetic crude oil. When completed, the Cold Lake project will be one of the largest facilities for producing crude bitumen from wells in the world.

  8. Boom and future of radioactive prospecting for oil and gas

    SciTech Connect (OSTI)

    Yuande, Q.; Jinhua, L.; Youqing, Z.; Longchang, W. )

    1992-01-01

    In this paper, the authors sketch out the general development situation of radioactive oil and gas explorations, the mechanism of radioactive anomaly, the application of radon method to oil and gas explorations, and some examples. It is pointed out that with the advance of science and technology, radioactive method will get consummate and very promising in oil and gas explorations.

  9. Removal of metals from heavy oils with phosphorus - Alumina catalysts

    SciTech Connect (OSTI)

    Kukes, S.G.; Parrott, S.L.; Gardner, L.E. )

    1987-04-01

    Earlier it was found that various oil-soluble phosphorous compounds were active for vanadium removal from different crude oils. The phosphorous compounds preferentially reacted with low molecular weight vanadium species in the resin fraction and therefore the highest rate of vanadium removal was observed when the asphaltene fraction was partially or completely removed. Phosphorous compounds promoted the rate of vanadium removal during hydroprocessing over alumina in a trickle bed reactor. Some metal phosphates were prepared and tested for demetallization activity. Several mixed metal phosphates, such as Cr-Zr, Ni-Zr, Cu-Zr, V-Co-Zr, Fe-Co-Zr, Ni-Co-Zr, etc., exhibited high activity for both vanadium and nickel removal. These catalysts were found to possess HDM activity and activity maintenance comparable to conventional hydrotreating catalysts available commercially. The vanadium removal selectivity of the mixed metal phosphates was similar to that of the commercial catalyst, but much lower than that observed earlier for oil soluble phosphorous compounds. Since the lack of high vanadium selectivity for the mixed metal phosphates could be due to their transition metal component, they investigated the hydroprocessing of heavy oils over aluminas impregnated with different inorganic phosphorous compounds.

  10. Future oil and gas: Can Iran deliver?

    SciTech Connect (OSTI)

    Takin, M.

    1996-11-01

    Iran`s oil and gas production and exports constitute the country`s main source of foreign exchange earnings. The future level of these earnings will depend on oil prices, global demand for Iranian exports, the country`s productive capability and domestic consumption. The size of Iranian oil reserves suggests that, in principle, present productive capacity could be maintained and expanded. However, the greatest share of production in coming years still will come from fields that already have produced for several decades. In spite of significant remaining reserves, these fields are not nearly as prolific as they were in their early years. The operations required for further development are now more complicated and, in particular, more costly. These fields` size also implies that improving production, and instituting secondary and tertiary recovery methods (such as gas injection), will require mega-scale operations. This article discusses future oil and gas export revenues from the Islamic Republic of Iran, emphasizing the country`s future production and commenting on the effects of proposed US sanctions.

  11. Evaluating oil quality and monitoring production from heavy oil reservoirs using geochemical methods: Application to the Boscan Field, Venezuela

    SciTech Connect (OSTI)

    Kaufman, R.L.; Noguera, V.H.; Bantz, D.M.; Rodriguez, R.

    1996-08-01

    Many oil fields worldwide contain heavy oil in one or more reservoir units. The low gravity of these oils is most frequently due to biodegradation and/or low maturity. The challenge is to find ways to economically recover this oil. Methods which reduce the operating costs of producing heavy oil add significant value to such projects. Geochemical techniques which use the composition of the reservoir fluids as natural tracers offer cost effective methods to assist with reservoir management. The low viscosity and gravity of heavy oil, combined with frequent high water cuts, low flow rates, and the presence of downhole artificial lift equipment, make many conventional production logging methods difficult to apply. Therefore, monitoring production, especially if the produced oil is commingled from multiple reservoirs, can be difficult. Geochemical methods can be used to identify oil/water contacts, tubing string leaks and to allocate production to individual zones from commingled production. An example of a giant heavy oil field where geochemical methods may be applicable is the Boscan Field in Venezuela. Low maturity oil, averaging 10{degrees} API gravity, is produced from the Eocene Upper and Lower Boscan (Miosa) Sands. Geochemical, stratigraphic and engineering data have helped to better define the controls on oil quality within the field, identified new reservoir compartments and defined unique characteristics of the Upper and Lower Boscan oils. This information can be used to identify existing wells in need of workovers due to mechanical problems and to monitor production from new infill wells.

  12. Prospects for applications of electron beams in processing of gas and oil hydrocarbons

    SciTech Connect (OSTI)

    Ponomarev, A. V.; Pershukov, V. A.; Smirnov, V. P.

    2015-12-15

    Waste-free processing of oil and oil gases can be based on electron-beam technologies. Their major advantage is an opportunity of controlled manufacturing of a wide range of products with a higher utility value at moderate temperatures and pressures. The work considers certain key aspects of electron beam technologies applied for the chain cracking of heavy crude oil, for the synthesis of premium gasoline from oil gases, and also for the hydrogenation, alkylation, and isomerization of unsaturated oil products. Electronbeam processing of oil can be embodied via compact mobile modules which are applicable for direct usage at distant oil and gas fields. More cost-effective and reliable electron accelerators should be developed to realize the potential of electron-beam technologies.

  13. Top 100 Oil and Gas Fields of 2009

    U.S. Energy Information Administration (EIA) Indexed Site

    Top 100 Oil and Gas Fields of 2009 Introduction This supplement to the Energy Information Administration's summary of U.S. Crude Oil, Natural Gas, and Natural Gas Liquids Proved Reserves, 2009 ranks the United States' largest oil and gas fields by their estimated 2009 proved reserves. The Top 100's Share of U.S. Proved Reserves in 2009 The Top 100 oil fields and Top 100 gas fields each accounted for about 60 percent of the respective total proved reserves of the United States. The Top 100 oil

  14. New short contact time processes upgrade residual oils and heavy crudes

    SciTech Connect (OSTI)

    Not Available

    1991-08-12

    This paper reports on new short contact time carbon rejection technology developed for upgrading residual oils and converting heavier crudes into high-quality synthetic crudes. The process, called discriminatory destructive distillation, or 3D, has been demonstrated in a Kansas refinery on feedstocks ranging from 13.5 to 30.6{degrees} API. For the past year, Coastal Derby Refining Co. has been operating a revolutionary, according to Bartholic, circulating fluid solids processing apparatus that can be run as either a 3D process unit, to virtually eliminate the residual oil component of crude, or as an MSCC process unit, to upgrade VGO residual oils. Because both of these processes circulate a fluid solid in a manner similar to the well known and commercially accepted fluid catalytic cracking (FCC) process, existing FCC-type units can be easily and economically converted to either 3D or MSCC operation. The 3D process is a low-pressure, carbon-rejection residual oil treating process for preparation of gas oils for fluid catalytic cracking (or MSCC), hydrotreating, mild hydrocracking, or full hydrocracking, says Bartholic. The process is also applicable, he says to upgrading heavy crudes or tar sands bitumen to high-quality reconstituted crudes for world markets.

  15. Oil/gas separator for installation at burning wells

    DOE Patents [OSTI]

    Alonso, Carol T.; Bender, Donald A.; Bowman, Barry R.; Burnham, Alan K.; Chesnut, Dwayne A.; Comfort, III, William J.; Guymon, Lloyd G.; Henning, Carl D.; Pedersen, Knud B.; Sefcik, Joseph A.; Smith, Joseph A.; Strauch, Mark S.

    1993-01-01

    An oil/gas separator is disclosed that can be utilized to return the burning wells in Kuwait to production. Advantageously, a crane is used to install the separator at a safe distance from the well. The gas from the well is burned off at the site, and the oil is immediately pumped into Kuwait's oil gathering system. Diverters inside the separator prevent the oil jet coming out of the well from reaching the top vents where the gas is burned. The oil falls back down, and is pumped from an annular oil catcher at the bottom of the separator, or from the concrete cellar surrounding the well.

  16. Oil/gas separator for installation at burning wells

    DOE Patents [OSTI]

    Alonso, C.T.; Bender, D.A.; Bowman, B.R.; Burnham, A.K.; Chesnut, D.A.; Comfort, W.J. III; Guymon, L.G.; Henning, C.D.; Pedersen, K.B.; Sefcik, J.A.; Smith, J.A.; Strauch, M.S.

    1993-03-09

    An oil/gas separator is disclosed that can be utilized to return the burning wells in Kuwait to production. Advantageously, a crane is used to install the separator at a safe distance from the well. The gas from the well is burned off at the site, and the oil is immediately pumped into Kuwait's oil gathering system. Diverters inside the separator prevent the oil jet coming out of the well from reaching the top vents where the gas is burned. The oil falls back down, and is pumped from an annular oil catcher at the bottom of the separator, or from the concrete cellar surrounding the well.

  17. Heavy oil reservoirs recoverable by thermal technology. Annual report

    SciTech Connect (OSTI)

    Kujawa, P.

    1981-02-01

    This volume contains reservoir, production, and project data for target reservoirs which contain heavy oil in the 8 to 25/sup 0/ API gravity range and are susceptible to recovery by in situ combustion and steam drive. The reservoirs for steam recovery are less than 2500 feet deep to comply with state-of-the-art technology. In cases where one reservoir would be a target for in situ combustion or steam drive, that reservoir is reported in both sections. Data were collectd from three source types: hands-on (A), once-removed (B), and twice-removed (C). In all cases, data were sought depicting and characterizing individual reservoirs as opposed to data covering an entire field with more than one producing interval or reservoir. The data sources are listed at the end of each case. This volume also contains a complete listing of operators and projects, as well as a bibliography of source material.

  18. New noncatalytic heavy-oil process developed in Canada

    SciTech Connect (OSTI)

    Fisher, I.P.; Souhrada, F.; Woods, H.J.

    1982-11-22

    Describes Gulf Canada's hydrogen addition upgrading process, named Donor Refined Bitumen (DRB), which involves the pyrolysis of the residuum portion of the bitumen or heavy oil in the presence of an efficient hydrogen donor that stabilizes the intermediates from the pyrolyzing bitumen. Advantages are high operability and reliability, low capital and operating costs, high yields and good product quality, feedstock and independence, the use of conventional refinery equipment, and ready availability of high quality donor. Presents a schematic flow sheet of the DRB process showing how bitumen is upgraded sufficiently to allow easy pipelining to a central major upgrading plant. Tables give comparative compositional data on middle distillates; naptha compositions and qualities; and operating costs.

  19. Heavy oil reservoirs recoverable by thermal technology. Annual report

    SciTech Connect (OSTI)

    Kujawa, P.

    1981-02-01

    This volume contains reservoir, production, and project data for target reservoirs thermally recoverable by steam drive which are equal to or greater than 2500 feet deep and contain heavy oil in the 8 to 25/sup 0/ API gravity range. Data were collected from three source types: hands-on (A), once-removed (B), and twice-removed (C). In all cases, data were sought depicting and characterizing individual reservoirs as opposed to data covering an entire field with more than one producing interval or reservoir. The data sources are listed at the end of each case. This volume also contains a complete listing of operators and projects, as well as a bibliography of source material.

  20. "U.S. Crude Oil, Natural Gas, and Natural Gas Liquids Reserves...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil, Natural Gas, and Natural Gas Liquids Reserves Summary Data Tables, 2014" "Contents" "Table 1: U.S. proved reserves, and reserves changes, 2013-14" "Table 2: U.S. tight oil ...

  1. Water-related Issues Affecting Conventional Oil and Gas Recovery...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Water-related Issues Affecting Conventional Oil and Gas Recovery and Potential Oil-Shale Development in the Uinta Basin, Utah Citation Details In-Document Search ...

  2. Illinois Natural Gas Withdrawals from Oil Wells (Million Cubic...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) Illinois Natural Gas Withdrawals from Oil Wells (Million Cubic Feet) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1991 1 1 1 1 1 1 2 1 1 1 1...

  3. Water-related Issues Affecting Conventional Oil and Gas Recovery...

    Office of Scientific and Technical Information (OSTI)

    Water-related Issues Affecting Conventional Oil and Gas Recovery and Potential Oil-Shale Development in the Uinta Basin, Utah Citation Details In-Document Search Title: Water-re...

  4. Indiana Natural Gas Withdrawals from Oil Wells (Million Cubic...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) Indiana Natural Gas Withdrawals from Oil Wells (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 ...

  5. Other States Natural Gas Gross Withdrawals from Oil Wells (Million...

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil Wells (Million Cubic Feet) Other States Natural Gas Gross Withdrawals from Oil Wells (Million Cubic Feet) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1991 3,459 3,117 ...

  6. Missouri Natural Gas Gross Withdrawals from Oil Wells (Million...

    U.S. Energy Information Administration (EIA) Indexed Site

    from Oil Wells (Million Cubic Feet) Missouri Natural Gas Gross Withdrawals from Oil Wells (Million Cubic Feet) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 ...

  7. Oil and natural gas market outlook and drivers

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFS | Oil and natural gas market outlook and drivers, May 18, 2016 Global supply has ... WTI price dollars per barrel EIA expects WTI oil prices to remain low compared to recent ...

  8. Top 100 U.S. Oil and Gas Fields

    U.S. Energy Information Administration (EIA) Indexed Site

    Oil and Gas Fields March 2015 Independent Statistics & Analysis www.eia.gov U.S. Department of Energy Washington, DC 20585 U.S. Energy Information Administration | Top 100 U.S. Oil ...

  9. Water-related Issues Affecting Conventional Oil and Gas Recovery...

    Office of Scientific and Technical Information (OSTI)

    Water-related Issues Affecting Conventional Oil and Gas Recovery and Potential Oil-Shale Development in the Uinta Basin, Utah Citation Details In-Document Search Title: Water-relat...

  10. Oil and Gas R&D Programs

    SciTech Connect (OSTI)

    1997-03-01

    This publication describes the major components of the research and development programs of the Department of Energy`s Office of Natural Gas and Petroleum Technology. These programs are commonly referred to collectively as the `Oil and Gas Program.` This document provides customers with a single source of information describing the details of the individual technology program components. This document reflects the results of a planning cycle that began in early 1996 with the development of a scenario analysis for the programs, followed by the development of the coordinated strategic plan. The technology program plans, which are the most recent products of the planning cycle, expand on the program descriptions presented in the coordinated strategic plan, and represent an initial effort to coordinate the Oil and Gas Program exploration and production programs and budgets. Each technology program plan includes a `roadmap` that summarizes the progress of the program to the present and indicates its future direction. The roadmaps describe the program drivers, vision, mission, strategies, and measures of success. Both the individual technology program plans and the strategic plan are dynamic and are intended to be updated regularly.