Powered by Deep Web Technologies
Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

G-Band Vapor Radiometer Profiler (GVRP) Handbook  

SciTech Connect

The G-Band Vapor Radiometer Profiler (GVRP) provides time-series measurements of brightness temperatures from 15 channels between 170 and 183.310 GHz. Atmospheric emission in this spectral region is primarily due to water vapor, with some influence from liquid water. Channels between 170.0 and 176.0 GHz are particularly sensitive to the presence of liquid water. The sensitivity to water vapor of the 183.31-GHz line is approximately 30 times higher than at the frequencies of the two-channel microwave radiometer (MWR) for a precipitable water vapor (PWV) amount of less than 2.5 mm. Measurements from the GVRP instrument are therefore especially useful during low-humidity conditions (PWV < 5 mm). In addition to integrated water vapor and liquid water, the GVRP can provide low-resolution vertical profiles of water vapor in very dry conditions.

Caddeau, MP

2010-06-23T23:59:59.000Z

2

G-Band Vapor Radiometer Precipitable Water Vapor (GVRPWV) Value-Added Product  

SciTech Connect

The G-Band Vapor Radiometer Precipitable Water Vapor (GVRPWV) value-added product (VAP) computes precipitable water vapor using neural network techniques from data measured by the GVR. The GVR reports time-series measurements of brightness temperatures for four channels located at 183.3 ± 1, 3, 7, and 14 GHz.

Koontz, A; Cadeddu, M

2012-12-05T23:59:59.000Z

3

GVR (G-Band Vapor Radiometer) M.P. Cadeddu and J.C. Liljegren Argonne Natl. Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

MWR status MWR status M.P. Cadeddu New radiometers New radiometers ECO-00664 (MWR procurement) open Specifications have been written and submitted Draft of specifications sent to vendors last month A few changes were incorporated after vendors feedback. Final specification document will be sent next week. ECO-00664 (MWR procurement) open Specifications have been written and submitted Draft of specifications sent to vendors last month A few changes were incorporated after vendors feedback. Final specification document will be sent next week. PWV-LWP: 12 2-channel MWR Temperature-humidity profile: 2 profilers operating Low LWP-PWV: 2 183-GHz radiometers Low LWP: 2 90/150-GHz radiometers PWV-LWP: 12 2-channel MWR Temperature-humidity profile: 2 profilers

4

GVR (G-Band Vapor Radiometer) M.P. Cadeddu and J.C. Liljegren Argonne Natl. Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

ARM 90/150 GHz data at ARM 90/150 GHz data at COPS M.P. Cadeddu, A. Vogelmann, D.D. Turner, S. Crewell, U. Lönhert MWRHF (90/150) data Data available at archives from 06/22 to 12/31 Challenges associated with instrument: New instrument - new technology We still need to learn about calibration Spectral region (WV continuum) still uncertain in models Data available at archives from 06/22 to 12/31 Challenges associated with instrument: New instrument - new technology We still need to learn about calibration Spectral region (WV continuum) still uncertain in models Weather conditions were not ideal for the initial testing of the instrument. The radiometer did not calibrate from 06/30 until 10/13 The few calibrations in June may have been affected by dew formation Calibration of summer data is

5

MEASUREMENTS AND RETRIEVALS FROM A NEW 183-GHz WATER VAPOR RADIOMETER IN  

NLE Websites -- All DOE Office Websites (Extended Search)

MEASUREMENTS AND RETRIEVALS FROM A NEW 183-GHz WATER VAPOR RADIOMETER IN MEASUREMENTS AND RETRIEVALS FROM A NEW 183-GHz WATER VAPOR RADIOMETER IN THE ARCTIC Cadeddu, Maria Argonne National Laboratory Category: Instruments A new G-band (183 GHz) vapor radiometer (GVR), developed and built by Prosensing Inc. (http://www.prosensing.com), was deployed in Barrow, Alaska, in April 2005. The radiometer was deployed as part of the ongoing Atmospheric Radiation Measurement (ARM) program's effort to improve water vapor retrievals in the cold, dry Arctic environment. The instrument measures brightness temperatures from four double sideband channels centered at 1, 3, 7, and 14 GHz from the 183.31-GHz water vapor line. Atmospheric emission in this spectral region is primarily due to water vapor, with some influence from liquid water. The GVR will remain in Barrow

6

Measurements of atmospheric water vapor above Mauna Kea using an infrared radiometer  

E-Print Network (OSTI)

Measurements of atmospheric water vapor above Mauna Kea using an infrared radiometer David A in atmospheric water vapor that distort the phase coherence of incoming celestial signals. The signal received water vapor, this paper presents results obtained with a second generation IRMA operating at the James

Naylor, David A.

7

Integration of Global Positioning System and Scanning Water Vapor Radiometers for Precipitable Water Vapor and Cloud Liquid Path Estimates  

NLE Websites -- All DOE Office Websites (Extended Search)

Integration of Global Positioning System and Scanning Integration of Global Positioning System and Scanning Water Vapor Radiometers for Precipitable Water Vapor and Cloud Liquid Path Estimates V. Mattioli and P. Basili Department of Electronic and Information Engineering University of Perugia Perugia, Italy E. R. Westwater Cooperative Institute for Research in Environmental Sciences University of Colorado National Oceanic and Atmospheric Administration Environmental Technology Laboratory Boulder, Colorado Introduction In recent years the Global Positioning System (GPS) has proved to be a reliable instrument for measuring precipitable water vapor (PWV) (Bevis et al. 1992), offering an independent source of information on water vapor when compared with microwave radiometers (MWRs), and/or radiosonde

8

183-GHz Radiometer Handbook - November 2006  

SciTech Connect

The G-Band Vapor Radiometer (GVR) provides time-series measurements of brightness temperatures from four double sideband channels centered at ± 1, ± 3, ± 7, and ± 14 GHz around the 183.31-GHz water vapor line. Atmospheric emission in this spectral region is primarily due to water vapor, with some influence from liquid water. The 183.31 ± 14-GHz channel is particularly sensitive to the presence of liquid water. The sensitivity to water vapor of the 183.31-GHz line is approximately 30 times higher than at the frequencies of the two-channel microwave radiometer (MWR) for a precipitable water vapor (PWV) amount of less than 2.5 mm. Measurements from this nstrument are therefore especially useful during low-humidity conditions (PWV < 5 mm).

MP Cadeddu

2006-11-30T23:59:59.000Z

9

On the challenges of tomography retrievals of a 2D water vapor field using ground-based microwave radiometers: An observation system simulation experiment  

Science Journals Connector (OSTI)

Two-dimensional water vapor fields were retrieved by simulated measurements from multiple ground-based microwave radiometers using a tomographic approach. The goal of this paper was to investigate how the various aspects of the instrument set-up (...

Véronique Meunier; David D. Turner; Pavlos Kollias

10

Monitoring of Precipitable Water Vapor and Cloud Liquid Path from Scanning Microwave Radiometers During the 2003 Cloudiness Inter-Comparison Experiment  

NLE Websites -- All DOE Office Websites (Extended Search)

Monitoring of Precipitable Water Vapor and Cloud Liquid Monitoring of Precipitable Water Vapor and Cloud Liquid Path from Scanning Microwave Radiometers During the 2003 Cloudiness Inter-Comparison Experiment V. Mattioli Department of Electronic and Information Engineering University of Perugia Perugia, Italy E. R. Westwater Cooperative Institute for Research in Environmental Sciences University of Colorado National Oceanic and Atmospheric Administration Environmental Technology Laboratory Boulder, Colorado V. Morris Pacific Northwest National Laboratory Richland, Washington Introduction Ground-based microwave radiometers (MWR) are widely used to measure atmospheric precipitable water vapor (PWV) and cloud liquid path (CLP). Comparisons of PWV derived from MWRs with water vapor retrievals from instruments like radiosondes, Global Positioning System (GPS) and Raman

11

Microwave Radiometer (MWR) Handbook  

SciTech Connect

The Microwave Radiometer (MWR) provides time-series measurements of column-integrated amounts of water vapor and liquid water. The instrument itself is essentially a sensitive microwave receiver. That is, it is tuned to measure the microwave emissions of the vapor and liquid water molecules in the atmosphere at specific frequencies.

Morris, VR

2006-08-01T23:59:59.000Z

12

Microwave Radiometer-High Frequency (MWRHF) Handbook  

SciTech Connect

The 90/150-GHz Vapor Radiometer provides time-series measurements of brightness temperatures from two channels centered at 90 and 150 GHz. These two channels are sensitive to the presence of liquid water and precipitable water vapor.

Caddedu, MP

2011-03-17T23:59:59.000Z

13

Ground-Based Microwave Radiometer Measurements  

NLE Websites -- All DOE Office Websites (Extended Search)

Ground-Based Microwave Radiometer Measurements Ground-Based Microwave Radiometer Measurements and Radiosonde Comparisons During the WVIOP2000 Field Experiment D. Cimini University of L'Aquila L'Aquil, Italy E. R. Westwater Cooperative Institute for Research in the Environmental Sciences University of Colorado National Oceanic and Atmospheric Administration Environmental Technology Laboratory Boulder, Colorado Y. Han Science System Applications National Aeronautics Space Administration Goddard Space Flight Center Greenbelt, Maryland S. Keihm Jet Propulsion Laboratory California Institute of Technology Pasadena, California Introduction During September to October 2000, a water vapor intensive operational period (WVIOP) was conducted at the Atmospheric Radiation Measurement (ARM) Program's Southern Great Plains (SGP) Cloud and

14

Raman excitation profile of the G band in single-chirality carbon nanotubes  

E-Print Network (OSTI)

We present in this work measurements of the Raman excitation profile of the high-energy phonons (G band) in single-chirality (n,m) semiconducting single-wall carbon nanotubes using more than 70 laser excitation energies, ...

Moura, L. G.

15

Zone folding effect in Raman G-band intensity of twisted bilayer graphene  

E-Print Network (OSTI)

The G-band Raman intensity is calculated for twisted bilayer graphene as a function of laser excitation energy based on the extended tight binding method. Here we explicitly consider the electron-photon and electron-phonon ...

Dresselhaus, Mildred

16

Microwave Radiometer – 3 Channel (MWR3C) Handbook  

SciTech Connect

The microwave radiometer 3-channel (MWR3C) provides time-series measurements of brightness temperatures from three channels centered at 23.834, 30, and 89 GHz. These three channels are sensitive to the presence of liquid water and precipitable water vapor.

Cadeddu, MP

2012-05-04T23:59:59.000Z

17

Lighting Research Group: Facilities: Spectro-Radiometer  

NLE Websites -- All DOE Office Websites (Extended Search)

Spectro-Radiometer Spectro-Radiometer Spectro-Radiometer spectro-radiometer Gonio-photometer | Integrating sphere | Power analyzer | Spectro-radiometer The spectro-radiometer is used to measure the light output of a light source at each wavelength. The part that looks like a video camera (to the far right in the picture) can look at each wavelength separately. The spectro-radiometer can also be used as a standard light meter and measure all visible wavelengths at once to obtain the total light output of a source. The console portion of the spectro-radiometer is used to display the meter readings and also to adjust measurement settings like the sensitivity. The computer is interfaced with the spectro-radiometer and is used to send commands to the machine and receive, store, and analyze the data.

18

Spectroscopy with Multichannel Correlation Radiometers  

E-Print Network (OSTI)

Correlation radiometers make true differential measurements in power with high accuracy and small systematic errors. This receiver architecture has been used in radio astronomy for measurements of continuum radiation for over 50 years; this article examines spectroscopy over broad bandwidths using correlation techniques. After general discussions of correlation and the choice of hybrid phase, experimental results from tests with a simple laboratory multi-channel correlation radiometer are shown. Analysis of the effect of the input hybrid's phase shows that a 90 degree hybrid is likely to be the best general choice for radio astronomy, depending on its amplitude match and phase flatness with frequency. The laboratory results verify that the combination of the correlation architecture and an analog lag correlator is an excellent method for spectroscopy over very wide bandwidths.

A. I. Harris

2005-04-20T23:59:59.000Z

19

ARM - Field Campaign - Water Vapor IOP  

NLE Websites -- All DOE Office Websites (Extended Search)

govCampaignsWater Vapor IOP govCampaignsWater Vapor IOP Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : Water Vapor IOP 2000.09.18 - 2000.10.08 Lead Scientist : Henry Revercomb Data Availability Yes For data sets, see below. Description Scientific hypothesis: 1. Microwave radiometer (MWR) observations of the 22 GHz water vapor line can accurately constrain the total column amount of water vapor (assuming a calibration accuracy of 0.5 degC or better, which translates into 0.35 mm PWV). 2. Continuous profiling by Raman lidar provides a stable reference for handling sampling problems and observes a fixed column directly above the site only requiring a single height- independent calibration factor. 3. Agreement between the salt-bath calibrated in-situ probes, chilled

20

Novel Cyclotron-Based Radiometal Production  

SciTech Connect

Accomplishments: (1) Construction of prototype solution target for radiometal production; (2) Testing of prototype target for production of following isotopes: a. Zr-89. Investigation of Zr-89 production from Y-89 nitrate solution. i. Defined problems of gas evolution and salt precipitation. ii. Solved problem of precipitation by addition of nitric acid. iii. Solved gas evolution problem with addition of backpressure regulator and constant degassing of target during irradiations. iv. Investigated effects of Y-89 nitrate concentration and beam current. v. Published abstracts at SNM and ISRS meetings; (3) Design of 2nd generation radiometal solution target. a. Included reflux chamber and smaller target volume to conserve precious target materials. b. Included aluminum for prototype and tantalum for working model. c. Included greater varicosities for improved heat transfer; and, (4) Construction of 2nd generation radiometal solution target started.

DeGrado, Timothy R. [Mayo Clinic] [Mayo Clinic (United States)

2013-10-31T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

ARM - Instrument - gvr  

NLE Websites -- All DOE Office Websites (Extended Search)

govInstrumentsgvr govInstrumentsgvr Documentation GVR : Handbook GVR : Instrument Mentor Monthly Summary (IMMS) reports GVR : Data Quality Assessment (DQA) reports ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Instrument : G-band (183 GHz) Vapor Radiometer (GVR) Instrument Categories Radiometric Picture of the G-band (183 GHz) Vapor Radiometer (GVR) Picture of the G-band (183 GHz) Vapor Radiometer (GVR) General Overview The G-Band Vapor Radiometer (GVR) provides time-series measurements of brightness temperatures from four double sideband channels centered at ±1, ±3, ±7, and ±14 GHz around the 183.31-GHz water vapor line. Atmospheric emission in this spectral region is primarily due to water vapor, with some

22

SEARCHES FOR METAL-POOR STARS FROM THE HAMBURG/ESO SURVEY USING THE CH G BAND  

SciTech Connect

We describe a new method to search for metal-poor candidates from the Hamburg/ESO objective-prism survey (HES) based on identifying stars with apparently strong CH G-band strengths for their colors. The hypothesis we exploit is that large overabundances of carbon are common among metal-poor stars, as has been found by numerous studies over the past two decades. The selection was made by considering two line indices in the 4300 A region, applied directly to the low-resolution prism spectra. This work also extends a previously published method by adding bright sources to the sample. The spectra of these stars suffer from saturation effects, compromising the index calculations and leading to an undersampling of the brighter candidates. A simple numerical procedure, based on available photometry, was developed to correct the line indices and overcome this limitation. Visual inspection and classification of the spectra from the HES plates yielded a list of 5288 new metal-poor (and by selection, carbon-rich) candidates, which are presently being used as targets for medium-resolution spectroscopic follow-up. Estimates of the stellar atmospheric parameters, as well as carbon abundances, are now available for 117 of the first candidates, based on follow-up medium-resolution spectra obtained with the SOAR 4.1 m and Gemini 8 m telescopes. We demonstrate that our new method improves the metal-poor star fractions found by our pilot study by up to a factor of three in the same magnitude range, as compared with our pilot study based on only one CH G-band index. Our selection scheme obtained roughly a 40% success rate for identification of stars with [Fe/H] <-1.0; the primary contaminant is late-type stars with near-solar abundances and, often, emission line cores that filled in the Ca II K line on the prism spectrum. Because the selection is based on carbon, we greatly increase the numbers of known carbon-enhanced metal-poor stars from the HES with intermediate metallicities -2.0 < [Fe/H] <-1.0, which previous survey efforts undersampled. There are eight newly discovered stars with [Fe/H] <-3.0 in our sample, including two with [Fe/H] <-3.5.

Placco, Vinicius M.; Rossi, Silvia [Departamento de Astronomia-Instituto de Astronomia, Geofisica e Ciencias Atmosfericas, Universidade de Sao Paulo, Sao Paulo, SP 05508-090 (Brazil); Kennedy, Catherine R.; Beers, Timothy C.; Lee, Young Sun [Department of Physics and Astronomy and JINA (Joint Institute for Nuclear Astrophysics), Michigan State University, East Lansing, MI 48824 (United States); Christlieb, Norbert [Zentrum fuer Astronomie der Universitaet Heidelberg, Landessternwarte, Koenigstuhl 12, 69117 Heidelberg (Germany); Sivarani, Thirupathi [Indian Institute of Astrophysics, 2nd Block, Koramangala, Bangalore 560034 (India); Reimers, Dieter [Hamburger Sternwarte, Universitaet Hamburg, Gojenbergsweg 112, 21029 Hamburg (Germany); Wisotzki, Lutz, E-mail: vmplacco@astro.iag.usp.br [Astrophysical Institute Potsdam, An der Sternwarte 16, 14482 Potsdam (Germany)

2011-12-15T23:59:59.000Z

23

ARM - Field Campaign - Arctic Winter Water Vapor IOP  

NLE Websites -- All DOE Office Websites (Extended Search)

govCampaignsArctic Winter Water Vapor IOP govCampaignsArctic Winter Water Vapor IOP Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : Arctic Winter Water Vapor IOP 2004.03.09 - 2004.04.09 Lead Scientist : Ed Westwater Data Availability http://www.etl.noaa.gov/programs/2004/wviop/data will contain quicklooks of all of the data. For data sets, see below. Summary During the IOP, the Ground-based Scanning Radiometer of NOAA/ETL, and the ARM MicroWave Radiometer and Microwave Profiler, yielded excellent data over a range of conditions. In all, angular-scanned and calibrated radiometric data from 22.345 to 380 GHz were taken. The Precipitable Water Vapor varied about an order of magnitude from 1 to 10 mm, and surface temperatures varied from about -10 to -40 deg. Celcius. Vaisala RS90

24

Crookes's radiometers: a train of thought manifest  

Science Journals Connector (OSTI)

...radiant molecular energy of solar masses may at last be found...considered viscosity of the residual gas, and one of the Royal Society...He then described a little turbine radiometer not blacked at all...the warmer side, while the gas creeps around the edges from...

2010-01-01T23:59:59.000Z

25

Electrically calibrated absolute radiometer suitable for measurement automation  

Science Journals Connector (OSTI)

New electrically calibrated absolute radiometers (ESRs) were developed having fast response and high responsivity; these ESRs are specially useful for measurement automation. They are...

Boivin, Louis-Philippe; McNeely, Francis T

1986-01-01T23:59:59.000Z

26

Four absolute cavity radiometer (pyrheliometer) intercomparisons at New River, Arizona: radiometer standards  

SciTech Connect

Four detailed intercomparisons were made for a number of models of cavity-type self-calibrating radiometers (pyrheliometers). Each intercomparison consisted of simultaneous readings of pyrheliometers at 30-second intervals in runs of 10 minutes, with at least 15 runs per intercomparison. Twenty-seven instruments were in at least one intercomparison, and five were in all four. Summarized results and all raw data are provided from the intercomparisons.

Estey, R.S.; Seaman, C.H.

1981-07-01T23:59:59.000Z

27

ARM - VAP Process - gvrpwv  

NLE Websites -- All DOE Office Websites (Extended Search)

Productsgvrpwv Productsgvrpwv Documentation & Plots Technical Report Data Management Facility Plots (Quick Looks) ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send VAP : G-Band Vapor Radiometer Precipitable Water Vapor (GVRPWV) Instrument Categories Radiometric The G-Band Vapor Radiometer Precipitable Water Vapor (GVRPWV) value-added product (VAP) computes precipitable water vapor using neural network techniques from data measured by the GVR. The GVR reports time-series measurements of brightness temperatures for four channels located at 183.3 ± 1, 3, 7, and 14 GHz. For more details, see the technical report. Output Products gvr : G-band (183 GHz) Vapor Radiometer Primary Measurements The following measurements are those considered scientifically relevant.

28

Correlation of globe thermometer response and a YSI radiometer response  

E-Print Network (OSTI)

CORRELATION OF GLOBE THERMOMETER RESPONSE AND A YSI RADIOMETER RESPONSE A Thesis by ROBERT HOWARD FRANKNECHT Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE May 1979 Major Subjects Industrial Hygiene CORRELATION OF GLOBE THERMOMETER RESPONSE AND A YSI RADIOMETER RESPONSE A Thesis by ROBERT HOMARD FRANKNECHT Approved as to sty1e and content by: C'6~& . ~ Chairman of Committee ead...

Franknecht, Robert Howard

1979-01-01T23:59:59.000Z

29

Calibrations of filter radiometers for determination of atmospheric optical depth  

Science Journals Connector (OSTI)

Atmospheric optical depths are determined by relating ground-based measurements of direct solar radiation to the extraterrestrial value, I0, that a filter radiometer would read outside the atmosphere. Usually I0 is determined by the Langley extrapolation technique from a high-altitude site, where clear and highly stable atmospheric conditions may be found. Alternatively, I0 can be measured in situ from a stratospheric balloon experiment. We have employed both methods and found agreement to better than 1 %. Filter radiometers tend to change over time, especially when used operationally outdoors. Absolute calibrations in the laboratory are used to monitor the radiometric stability of filter radiometers at the Physikalisch-Meteorologisches Observatorium Davos (PMOD/WRC, Switzerland). A spectral calibration facility based on a calibrated trap detector from the Physikalisch-Technische Bundesanstalt (PTB, Germany) is used to relate the filter radiometer to an accurate and long-term traceable standard. An FEL-lamp-based standard, previously used for several years, was compared with the new trap standard via a filter radiometer at four wavelengths between 368 nm and 862 nm and revealed a systematic difference of the order of 5 %. The link between radiometric and I0 calibration is the value of the extraterrestrial solar spectrum at the filter radiometer wavelengths which can be determined from these two calibrations and compared with published values.

Ch Wehrli

2000-01-01T23:59:59.000Z

30

Ocean Water Vapor and Cloud Burden Trends Derived from the Topex Microwave Radiometer  

E-Print Network (OSTI)

. TMR OBSERVATIONS The TMR flew in a 10-day non-sun-synchronous exact repeat orbit with an inclination algorithm is a log-linear regression algorithm with coefficients that are stratified by wind speed and water

Ruf, Christopher

31

Calibrated vapor generator source  

DOE Patents (OSTI)

A portable vapor generator is disclosed that can provide a controlled source of chemical vapors, such as, narcotic or explosive vapors. This source can be used to test and calibrate various types of vapor detection systems by providing a known amount of vapors to the system. The vapor generator is calibrated using a reference ion mobility spectrometer. A method of providing this vapor is described, as follows: explosive or narcotic is deposited on quartz wool, placed in a chamber that can be heated or cooled (depending on the vapor pressure of the material) to control the concentration of vapors in the reservoir. A controlled flow of air is pulsed over the quartz wool releasing a preset quantity of vapors at the outlet. 10 figs.

Davies, J.P.; Larson, R.A.; Goodrich, L.D.; Hall, H.J.; Stoddard, B.D.; Davis, S.G.; Kaser, T.G.; Conrad, F.J.

1995-09-26T23:59:59.000Z

32

Evaluation of Radiometers Deployed at the National Renewable Energy Laboratory's Solar Radiation Research Laboratory  

SciTech Connect

This study analyzes the performance of various commercially available radiometers used for measuring global horizontal irradiances and direct normal irradiances. These include pyranometers, pyrheliometers, rotating shadowband radiometers, and a pyranometer with fixed internal shading and are all deployed at the National Renewable Energy Laboratory's Solar Radiation Research Laboratory. Data from 32 global horizontal irradiance and 19 direct normal irradiance radiometers are presented. The radiometers in this study were deployed for one year (from April 1, 2011, through March 31, 2012) and compared to measurements from radiometers with the lowest values of estimated measurement uncertainties for producing reference global horizontal irradiances and direct normal irradiances.

Habte, A.; Wilcox, S.; Stoffel, T.

2014-02-01T23:59:59.000Z

33

Differential Microwave Radiometer and the Cosmic Microwave Background |  

Office of Science (SC) Website

Differential Differential Microwave Radiometer and the Cosmic Microwave Background Laboratory Policy and Evaluation (LPE) LPE Home Staff M&O Contracts SC Laboratory Appraisal Process Laboratory Planning Process Work for Others in the Office of Science Laboratory Directed Research and Development (LDRD) DOE's Philosophy on LDRD Frequently Asked Questions Success Stories Brochures Additional Information LDRD Program Contacts Technology Transfer DOE National Laboratories Contact Information Laboratory Policy and Evaluation U.S. Department of Energy SC-32/Forrestal Building 1000 Independence Ave., SW Washington, DC 20585 P: (202) 586-5447 F: (202) 586-3119 Success Stories Differential Microwave Radiometer and the Cosmic Microwave Background Print Text Size: A A A RSS Feeds FeedbackShare Page

34

Quantitative Analysis of Spectral Impacts on Silicon Photodiode Radiometers  

SciTech Connect

Inexpensive broadband pyranometers with silicon photodiode detectors have a non-uniform spectral response over the spectral range of 300-1100 nm. The response region includes only about 70% to 75% of the total energy in the terrestrial solar spectral distribution from 300 nm to 4000 nm. The solar spectrum constantly changes with solar position and atmospheric conditions. Relative spectral distributions of diffuse hemispherical irradiance sky radiation and total global hemispherical irradiance are drastically different. This analysis convolves a typical photodiode response with SMARTS 2.9.5 spectral model spectra for different sites and atmospheric conditions. Differences in solar component spectra lead to differences on the order of 2% in global hemispherical and 5% or more in diffuse hemispherical irradiances from silicon radiometers. The result is that errors of more than 7% can occur in the computation of direct normal irradiance from global hemispherical irradiance and diffuse hemispherical irradiance using these radiometers.

Myers, D. R.

2011-01-01T23:59:59.000Z

35

Quantitative Analysis of Spectral Impacts on Silicon Photodiode Radiometers: Preprint  

SciTech Connect

Inexpensive broadband pyranometers with silicon photodiode detectors have a non-uniform spectral response over the spectral range of 300-1100 nm. The response region includes only about 70% to 75% of the total energy in the terrestrial solar spectral distribution from 300 nm to 4000 nm. The solar spectrum constantly changes with solar position and atmospheric conditions. Relative spectral distributions of diffuse hemispherical irradiance sky radiation and total global hemispherical irradiance are drastically different. This analysis convolves a typical photodiode response with SMARTS 2.9.5 spectral model spectra for different sites and atmospheric conditions. Differences in solar component spectra lead to differences on the order of 2% in global hemispherical and 5% or more in diffuse hemispherical irradiances from silicon radiometers. The result is that errors of more than 7% can occur in the computation of direct normal irradiance from global hemispherical irradiance and diffuse hemispherical irradiance using these radiometers.

Myers, D. R.

2011-04-01T23:59:59.000Z

36

Narrow Field of View Zenith Radiometer (NFOV) Handbook  

SciTech Connect

The two-channel narrow field-of-view radiometer (NFOV2) is a ground-based radiometer that looks straight up and measures radiance directly above the instrument at wavelengths of 673 and 870 nm. The field-of-view of the instrument is 1.2 degrees, and the sampling time resolution is one second. Measurements of the NFOV2 have been used to retrieve optical properties for overhead clouds that range from patchy to overcast. With a one-second sampling rate of the NFOV2, faster than almost any other ARM Climate Research Facility (ACRF) instrument, we are able, for the first time, to capture changes in cloud optical properties at the natural time scale of cloud evolution.

Chiu, C; Marshak, A; Hodges, G; Barnard, JC; Schmelzer, J

2008-11-01T23:59:59.000Z

37

ARM Water Vapor IOP  

NLE Websites -- All DOE Office Websites (Extended Search)

ARM Water Vapor IOP The SGP CART site will host the third ARM water vapor IOP on September 18-October 8, 2000. The CART site is home to a powerful array of instruments capable of...

38

Vapor spill monitoring method  

DOE Patents (OSTI)

Method for continuous sampling of liquified natural gas effluent from a spill pipe, vaporizing the cold liquified natural gas, and feeding the vaporized gas into an infrared detector to measure the gas composition. The apparatus utilizes a probe having an inner channel for receiving samples of liquified natural gas and a surrounding water jacket through which warm water is flowed to flash vaporize the liquified natural gas.

Bianchini, Gregory M. (Livermore, CA); McRae, Thomas G. (Livermore, CA)

1985-01-01T23:59:59.000Z

39

ARM - Water Vapor  

NLE Websites -- All DOE Office Websites (Extended Search)

Water Vapor Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About ARM Global...

40

Design of a differential radiometer for atmospheric radiative flux measurements  

SciTech Connect

The Hemispherical Optimized NEt Radiometer (HONER) is an instrument under development at the Los Alamos National Laboratory for deployment on an unmanned aerospace vehicle as part of the Atmospheric Radiation Measurements (ARM/UAV) program. HONER is a differential radiometer which will measure the difference between the total upwelling and downwelling fluxes and is intended to provide a means of measuring the atmospheric radiative flux divergence. Unlike existing instruments which measure the upwelling and downwelling fluxes separately, HONER will achieve an optical difference by chopping the two fluxes alternately onto a common pyroelectric detector. HONER will provide data resolved into two spectral bands; one covering the solar dominated region from less than 0.4 micrometer to approximately 4.5 micrometers and the other covering the region from approximately 4.5 micrometers to greater than 50 micrometers, dominated by thermal radiation. The means of separating the spectral regions guarantees seamless summation to calculate the total flux. The fields-of-view are near-hemispherical, upward and downward. The instrument can be converted, in flight, from the differential mode to absolute mode, measuring the upwelling and downwelling fluxes separately and simultaneously. The instrument also features continuous calibration from on-board sources. We will describe the design and operation of the sensor head and the on-board reference sources as well as the means of deployment.

LaDelfe, P.C.; Weber, P.G.; Rodriguez, C.W.

1994-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Ten channel background alpha radiometer for nondestructive analysis of low activity samples  

SciTech Connect

The description of a ten-channel alpha-radiometer based on large-area semiconductor detectors is presented in this paper. The radiometer is intended for determination of soil pollution by alpha-active radionuclides using thick samples. The analysis of isotopes is also provided. The concentrations of Pu and Am isotopes in soil samples are determined.

Pugatch, V.M.; Pavlenko, Y.N.; Vasiliev, Y.O.; Nenakhov, A.N.; Tkatch, N.M.; Barabash, L.I.; Berdnichenko, S.V.; Litovchenko, P.G.; Rosenfeld, A.B.; Zinets, O.S. (Inst. for Nuclear Research, Kiev (USSR))

1992-10-01T23:59:59.000Z

42

Calibration of a Solar Absolute Cavity Radiometer with Traceability to the World Radiometric Reference  

SciTech Connect

This report describes the present method of establishing traceability of absolute cavity radiometers to the World Radiometric Reference (WRR) through the process employed in the International Pyrheliometer Comparisons (IPC). This method derives the WRR reduction factor for each of the participating cavity radiometers. An alternative method is proposed, described, and evaluated as a way to reduce the uncertainty in the comparison process. The two methods are compared using a sample of data from the recent IPC-VIII conducted from September 25th to October 13th, 1995 at the World Radiation Center in Davos, Switzerland. A description of absolute cavity radiometers is also included, using a PMO-6 as an example of active cavity radiometers, and a HF as an example of passive cavity radiometers.

Reda, I.

1996-01-01T23:59:59.000Z

43

Working Group Reports A Short-Wave Radiometer Array Across  

NLE Websites -- All DOE Office Websites (Extended Search)

9 9 Working Group Reports A Short-Wave Radiometer Array Across the Tropical Pacific Ocean as a Component of the TOGA-TAO Buoy Array R. M. Reynolds Brookhaven National Laboratory Upton, New York Introduction The purpose of this document is to bring together pertinent information concerning the NOAA TOGA-TAO buoy array so that a decision can be made for the following questions: 1. Are the scientific gains from an array of short-wave radiation sensors in the equatorial Pacific Ocean sufficiently impelling that DOE/ARM should provide financial and material support to NOAA/PMEL to install and operate this array? 2. What scientists and/or scientific studies would directly benefit from such a data set? 3. What should that array look like? That is, what sub-set of buoys should be so implemented given the per-buoy

44

Characterization and calibration of 8-channel E-band heterodyne radiometer system for SST-1 tokamak  

SciTech Connect

An 8-channel E-band heterodyne radiometer system (74–86 GHz) is designed, characterized, and calibrated to measure the radial electron temperature profile by measuring Electron Cyclotron Emission spectrum at SST-1 Tokamak. The developed radiometer has a noise equivalent temperature of 1 eV and sensitivity of 5 × 10{sup 9} V/W. In order to precisely measure the absolute value of electron temperature, a calibration measurement of the radiometer system is performed using hot-cold Dicke switch method, which confirms the system linearity.

Siju, Varsha; Kumar, Dharmendra; Shukla, Praveena; Pathak, S. K. [Institute for Plasma Research, Bhat, Gandhinagar, Gujarat 382428 (India)] [Institute for Plasma Research, Bhat, Gandhinagar, Gujarat 382428 (India)

2014-05-15T23:59:59.000Z

45

Measurement of Boundary-Layer Temperature Profiles by a Scanning 5-MM Radiometer During the 1999 Winter NSA/AAO Radiometer Exp  

NLE Websites -- All DOE Office Websites (Extended Search)

Boundary-Layer Temperature Profiles by Boundary-Layer Temperature Profiles by a Scanning 5-MM Radiometer During the 1999 Winter NSA/AAO Radiometer Experiment and WVIOP 2000 V. Y. Leuski and E. R. Westwater Cooperative Institute for Research in the Environmental Sciences National Oceanic and Atmospheric Administration Environmental Technology Laboratory University of Colorado Boulder, Colorado Introduction A scanning 5-mm-wavelength radiometer was deployed during two Intensive Operational Periods (IOPs) at the Atmospheric Radiation Measurement (ARM) Program's Cloud and Radiation Testbed (CART) facilities. The first was conducted at the North Slope of Alaska (NSA) and Adjacent arctic Ocean (AAO) site near Barrow, Alaska, during March 1999. One goal was to evaluate the ability of an

46

DISCLAIMER  

NLE Websites -- All DOE Office Websites (Extended Search)

91 91 G-Band Vapor Radiometer Profiler (GVRP) Handbook MP Cadeddu Argonne National Laboratory June 2010 Work supported by the U.S. Department of Energy, Office of Science, Office of Biological and Environmental Research MP Cadeddu, June 2010, DOE/SC-ARM/TR-091 ii Contents 1.0 General Overview ................................................................................................................................. 1 2.0 Contacts ................................................................................................................................................ 1 2.1 Mentor .......................................................................................................................................... 1

47

Ocean Aerosols: The Marine Fast-Rotating Shadow-Band Radiometer Network  

NLE Websites -- All DOE Office Websites (Extended Search)

Ocean Aerosols: The Marine Fast-Rotating Ocean Aerosols: The Marine Fast-Rotating Shadow-Band Radiometer Network M. A. Miller, R. M. Reynolds, and J. J. Bartholomew Brookhaven National Laboratory Upton, New York Introduction A network of ship-mounted marine fast-rotating shadow-band radiometers (FRSRs) and broadband radiometers have been deployed over the fast four years on several backbone ships, funded jointly by Atmospheric Radiation Measurement (ARM) and National Aeronautic and Space Administration's (NASA's) Sensor Intercomparison and Merger for Biological and Interdisciplinary Studies (SIMBIOS). These radiometers operate continuously and automatically during daylight hours. There fundamental measurements made by the FRSRs in the network are the direct-normal irradiance

48

Evaluating Solar Resource Data Obtained from Multiple Radiometers Deployed at the National Renewable Energy Laboratory: Preprint  

SciTech Connect

Solar radiation resource measurements from radiometers are used to predict and evaluate the performance of photovoltaic and concentrating solar power systems, validate satellite-based models for estimating solar resources, and advance research in solar forecasting and climate change. This study analyzes the performance of various commercially available radiometers used for measuring global horizontal irradiances (GHI) and direct normal irradiances (DNI). These include pyranometers, pyrheliometers, rotating shadowband irradiometers, and a pyranometer with a shading ring deployed at the National Renewable Energy Laboratory's Solar Radiation Research Laboratory (SRRL). The radiometers in this study were deployed for one year (from April 1, 2011, through March 31, 2012) and compared to measurements from radiometers with the lowest values of estimated measurement uncertainties for producing reference GHI and DNI.

Habte, A.; Sengupta, M.; Andreas, A.; Wilcox, S.; Stoffel, T.

2014-09-01T23:59:59.000Z

49

Gasoline vapor recovery  

SciTech Connect

In a gasoline distribution network wherein gasoline is drawn from a gasoline storage tank and pumped into individual vehicles and wherein the gasoline storage tank is refilled periodically from a gasoline tanker truck, a method of recovering liquid gasoline from gasoline vapor that collects in the headspace of the gasoline storage tank as the liquid gasoline is drawn therefrom, said method comprising the steps of: (a) providing a source of inert gas; (b) introducing inert gas into the gasoline storage tank as liquid gasoline is drawn therefrom so that liquid gasoline drawn from the tank is displaced by inert gas and gasoline vapor mixes with the inert gas in the headspace of the tank; (c) collecting the inert gas/gasoline vapor mixture from the headspace of the gasoline storage tank as the tank is refilled from a gasoline tanker truck; (d) cooling the inert gas/gasoline vapor mixture to a temperature sufficient to condense the gasoline vapor in the mixture to liquid gasoline but not sufficient to liquify the inert gas in the mixture; (e) separating the condensed liquid gasoline from the inert gas; and delivering the condensed liquid gasoline to a remote location for subsequent use.

Lievens, G.; Tiberi, T.P.

1993-06-22T23:59:59.000Z

50

Electrolyte vapor condenser  

DOE Patents (OSTI)

A system is disclosed for removing electrolyte from a fuel cell gas stream. The gas stream containing electrolyte vapor is supercooled utilizing conventional heat exchangers and the thus supercooled gas stream is passed over high surface area passive condensers. The condensed electrolyte is then drained from the condenser and the remainder of the gas stream passed on. The system is particularly useful for electrolytes such as phosphoric acid and molten carbonate, but can be used for other electrolyte cells and simple vapor separation as well. 3 figs.

Sederquist, R.A.; Szydlowski, D.F.; Sawyer, R.D.

1983-02-08T23:59:59.000Z

51

Electrolyte vapor condenser  

DOE Patents (OSTI)

A system is disclosed for removing electrolyte from a fuel cell gas stream. The gas stream containing electrolyte vapor is supercooled utilizing conventional heat exchangers and the thus supercooled gas stream is passed over high surface area passive condensers. The condensed electrolyte is then drained from the condenser and the remainder of the gas stream passed on. The system is particularly useful for electrolytes such as phosphoric acid and molten carbonate, but can be used for other electrolyte cells and simple vapor separation as well.

Sederquist, Richard A. (Newington, CT); Szydlowski, Donald F. (East Hartford, CT); Sawyer, Richard D. (Canton, CT)

1983-01-01T23:59:59.000Z

52

Organic vapor jet printing system  

SciTech Connect

An organic vapor jet printing system includes a pump for increasing the pressure of an organic flux.

Forrest, Stephen R

2012-10-23T23:59:59.000Z

53

Mercury Vapor | Open Energy Information  

Open Energy Info (EERE)

Mercury Vapor Mercury Vapor Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Mercury Vapor Details Activities (23) Areas (23) Regions (0) NEPA(0) Exploration Technique Information Exploration Group: Lab Analysis Techniques Exploration Sub Group: Fluid Lab Analysis Parent Exploration Technique: Fluid Lab Analysis Information Provided by Technique Lithology: Stratigraphic/Structural: Anomalously high concentrations can indicate high permeability or conduit for fluid flow Hydrological: Field wide soil sampling can generate a geometrical approximation of fluid circulation Thermal: High concentration in soils can be indicative of active hydrothermal activity Dictionary.png Mercury Vapor: Mercury is discharged as a highly volatile vapor during hydrothermal

54

Stratified vapor generator  

DOE Patents (OSTI)

A stratified vapor generator (110) comprises a first heating section (H.sub.1) and a second heating section (H.sub.2). The first and second heating sections (H.sub.1, H.sub.2) are arranged so that the inlet of the second heating section (H.sub.2) is operatively associated with the outlet of the first heating section (H.sub.1). A moisture separator (126) having a vapor outlet (164) and a liquid outlet (144) is operatively associated with the outlet (124) of the second heating section (H.sub.2). A cooling section (C.sub.1) is operatively associated with the liquid outlet (144) of the moisture separator (126) and includes an outlet that is operatively associated with the inlet of the second heating section (H.sub.2).

Bharathan, Desikan (Lakewood, CO); Hassani, Vahab (Golden, CO)

2008-05-20T23:59:59.000Z

55

A 16-channel heterodyne electron cyclotron emission radiometer on J-TEXT  

SciTech Connect

To study equilibrium temporal dynamics and the mechanisms of magnetohydrodynamic instabilities, a 16-channel heterodyne electron cyclotron emission (ECE) radiometer has been developed to view the J-TEXT tokamak from the low field side. The ECE radiometer detects second-harmonic extraordinary mode in the frequency band of 94-125 GHz which corresponds to resonances from 1.8 T to 2.2 T. This ECE system consists of an ECE transmission line, a radio frequency unit, and two 8-channel intermediate frequency units. An in situ blackbody calibration source is applied for system calibration by comparison of hot and cold sources in order to provide an absolute temperature measurement.

Yang, Z. J.; Zhuang, G.; Xiao, J. S.; Wang, Z. J. [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China); Key Laboratory of Fusion and Advanced Electromagnetic Technology Ministry of Education, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China); Phillips, P. E.; Huang, H.; Rowan, W. L. [Institute for Fusion Studies, University of Texas at Austin, Austin, Texas 78712 (United States)

2012-10-15T23:59:59.000Z

56

Vapor Barriers or Vapor Diffusion Retarders | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Home Air Sealing for New Home Construction Insulation Types of Insulation Insulation and Air Sealing Products and Services External Resources Find a Local AirVapor Barrier...

57

Vapor spill pipe monitor  

DOE Patents (OSTI)

The invention is a method and apparatus for continually monitoring the composition of liquefied natural gas flowing from a spill pipe during a spill test by continually removing a sample of the LNG by means of a probe, gasifying the LNG in the probe, and sending the vaporized LNG to a remote ir gas detector for analysis. The probe comprises three spaced concentric tubes surrounded by a water jacket which communicates with a flow channel defined between the inner and middle, and middle and outer tubes. The inner tube is connected to a pump for providing suction, and the probe is positioned in the LNG flow below the spill pipe with the tip oriented partly downward so that LNG is continuously drawn into the inner tube through a small orifice. The probe is made of a high thermal conductivity metal. Hot water is flowed through the water jacket and through the flow channel between the three tubes to provide the necessary heat transfer to flash vaporize the LNG passing through the inner channel of the probe. The gasified LNG is transported through a connected hose or tubing extending from the probe to a remote ir sensor which measures the gas composition.

Bianchini, G.M.; McRae, T.G.

1983-06-23T23:59:59.000Z

58

Simultaneous Retreival of Surface Wind Speed and Rain Rate using Radar and Radiometer Measurements  

E-Print Network (OSTI)

to simultaneously retrieve the vertical profile of precipitation and the near-surface wind speed. ResultsSimultaneous Retreival of Surface Wind Speed and Rain Rate using Radar and Radiometer Measurements simultaneously estimates the over ocean near-surface wind speed and rain rate profile using data from a 10.7 GHz

Ruf, Christopher

59

Outgassing, Temperature Gradients and the Radiometer Effect in LISA: A Torsion Pendulum Investigation  

E-Print Network (OSTI)

Thermal modeling of the LISA gravitational reference sensor (GRS) includes such effects as outgassing from the proof mass and its housing and the radiometer effect. Experimental data in conditions emulating the LISA GRS are required to confidently predict the GRS performance. Outgassing and the radiometer effect are similar in characteristics and are difficult to decouple experimentally. The design of our torsion balance allows us to investigate differential radiation pressure, the radiometer effect, and outgassing on closely separated conducting surfaces with high sensitivity. A thermally controlled split copper plate is brought near a freely hanging plate-torsion pendulum.We have varied the temperature on each half of the copper plate and have measured the resulting forces on the pendulum. We have determined that to first order the current GRS model for the radiometer effect, outgassing, and radiation pressure are mostly consistent with our torsion balance measurements and therefore these thermal effects do not appear to be a large hindrance to the LISA noise budget. However, there remain discrepancies between the predicted dependence of these effects on the temperature of our apparatus.

Scott E Pollack; Stephan Schlamminger; Jens H Gundlach

2007-02-08T23:59:59.000Z

60

Hydrogen Cars and Water Vapor  

E-Print Network (OSTI)

. This cycle is currently under way with hydrogen fuel cells. As fuel cell cars are suggested as a solutionHydrogen Cars and Water Vapor D.W.KEITHANDA.E.FARRELL'S POLICY FORUM "Rethinking hydrogen cars" (18 misidentified as "zero-emissions vehicles." Fuel cell vehicles emit water vapor. A global fleet could have

Colorado at Boulder, University of

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Fuel vapor control device  

SciTech Connect

A fuel vapor control device is described having a valve opening and closing a passage connecting a carburetor and a charcoal canister according to a predetermined temperature. A first coil spring formed by a ''shape memory effect'' alloy is provided to urge the valve to open the passage when the temperature is high. A second coil spring urges the valve to close the passage. A solenoid is provided to urge an armature against the valve to close the passage against the force of the first coil spring when the engine is running. The solenoid heats the first coil spring to generate a spring force therein when the engine is running. When the engine is turned off, the solenoid is deactivated, and the force of the first spring overcomes the force of the second spring to open the passage until such time as the temperature of the first spring drops below the predetermined temperature.

Ota, I.; Nishimura, Y.; Nishio, S.; Yogo, K.

1987-10-20T23:59:59.000Z

62

The Dust Settles on Water Vapor Feedback  

Science Journals Connector (OSTI)

...To understand water vapor feedback...shifts in the atmospheric circulation...caused a positive water vapor feedback...temperature. Condensation, evaporation...shifts in the atmospheric circulation...caused a positive water vapor feedback...temperature. Condensation, evaporation...

Anthony D. Del Genio

2002-04-26T23:59:59.000Z

63

Category:Mercury Vapor | Open Energy Information  

Open Energy Info (EERE)

search GEOTHERMAL ENERGYGeothermal Home Geothermalpower.jpg Looking for the Mercury Vapor page? For detailed information on Mercury Vapor as exploration techniques,...

64

Using a cold radiometer to measure heat loads and survey heat leaks  

SciTech Connect

We have developed an inexpensive cold radiometer for use in thermal/vacuum chambers to measure heat loads, characterize emissivity and specularity of surfaces and to survey areas to evaluate stray heat loads. We report here the results of two such tests for the James Webb Space Telescope to measure heat loads and effective emissivities of 2 major pieces of optical ground support equipment that will be used in upcoming thermal vacuum testing of the Telescope.

DiPirro, M.; Tuttle, J.; Hait, T.; Shirron, P. [Cryogenics and Fluids Branch, NASA/Goddard Space Flight Center, Greenbelt MD 20771 (United States)

2014-01-29T23:59:59.000Z

65

Vapor deposition of hardened niobium  

DOE Patents (OSTI)

A method of coating ceramic nuclear fuel particles containing a major amount of an actinide ceramic in which the particles are placed in a fluidized bed maintained at ca. 800.degree. to ca. 900.degree. C., and niobium pentachloride vapor and carbon tetrachloride vapor are led into the bed, whereby niobium metal is deposited on the particles and carbon is deposited interstitially within the niobium. Coating apparatus used in the method is also disclosed.

Blocher, Jr., John M. (Columbus, OH); Veigel, Neil D. (Columbus, OH); Landrigan, Richard B. (Columbus, OH)

1983-04-19T23:59:59.000Z

66

Chemical vapor deposition sciences  

SciTech Connect

Chemical vapor deposition (CVD) is a widely used method for depositing thin films of a variety of materials. Applications of CVD range from the fabrication of microelectronic devices to the deposition of protective coatings. New CVD processes are increasingly complex, with stringent requirements that make it more difficult to commercialize them in a timely fashion. However, a clear understanding of the fundamental science underlying a CVD process, as expressed through computer models, can substantially shorten the time required for reactor and process development. Research scientists at Sandia use a wide range of experimental and theoretical techniques for investigating the science of CVD. Experimental tools include optical probes for gas-phase and surface processes, a range of surface analytic techniques, molecular beam methods for gas/surface kinetics, flow visualization techniques and state-of-the-art crystal growth reactors. The theoretical strategy uses a structured approach to describe the coupled gas-phase and gas-surface chemistry, fluid dynamics, heat and mass transfer of a CVD process. The software used to describe chemical reaction mechanisms is easily adapted to codes that model a variety of reactor geometries. Carefully chosen experiments provide critical information on the chemical species, gas temperatures and flows that are necessary for model development and validation. This brochure provides basic information on Sandia`s capabilities in the physical and chemical sciences of CVD and related materials processing technologies. It contains a brief description of the major scientific and technical capabilities of the CVD staff and facilities, and a brief discussion of the approach that the staff uses to advance the scientific understanding of CVD processes.

NONE

1992-12-31T23:59:59.000Z

67

ARM - PI Product - MWR Retrievals of Cloud Liquid Water and Water Vapor  

NLE Websites -- All DOE Office Websites (Extended Search)

govDataPI Data ProductsMWR Retrievals of Cloud Liquid Water and Water govDataPI Data ProductsMWR Retrievals of Cloud Liquid Water and Water Vapor Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send PI Product : MWR Retrievals of Cloud Liquid Water and Water Vapor 2005.02.01 - 2011.04.25 Site(s) FKB GRW HFE NIM PYE SBS General Description A new algorithm is being developed for the ARM Program to derive liquid water path (LWP) and precipitable water vapor (PWV) from the 2-channel (23.8 and 31.4 GHz) microwave radiometers (MWRs) deployed at ARM climate research facilities. This algorithm utilizes the "monoRTM" radiative transfer model (http://rtweb.aer.com), a combination of both an advanced statistical and physical-iterative retrieval, and brightness temperature offsets applied before the retrieval is performed. This allows perhaps the

68

The Vaporization Enthalpies and Vapor Pressures of Some Primary Amines of Pharmaceutical Importance by Correlation Gas  

E-Print Network (OSTI)

by Correlation Gas Chromatography Chase Gobble, Nigam Rath, and James Chickos* Department of Chemistry Information ABSTRACT: Vapor pressures, vaporization, and sublimation enthalpies of several pharmaceuticals and boiling temperatures when available. Sublimation enthalpies and vapor pressures are also evaluated for 1

Chickos, James S.

69

ARM - Datastreams - gvr  

NLE Websites -- All DOE Office Websites (Extended Search)

Datastreamsgvr Datastreamsgvr Documentation Data Quality Plots Citation DOI: 10.5439/1095594 [ What is this? ] Generate Citation ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Datastream : GVR G-band (183 GHz) Vapor Radiometer Active Dates 2006.09.28 - 2014.01.02 Measurement Categories Atmospheric State, Radiometric Originating Instrument G-band (183 GHz) Vapor Radiometer (GVR) Measurements Only measurements considered scientifically relevant are shown below by default. Show all measurements Measurement Units Variable Altitude above mean sea level m alt Base time in Epoch seconds since 1970-1-1 0:00:00 0:00 base_time 183.3 +/- 1 GHz hot load signal count hot1 ( time ) 183.3 +/- 3 GHz hot load signal count hot3 ( time )

70

ARM - Datastreams - gvrp  

NLE Websites -- All DOE Office Websites (Extended Search)

Datastreamsgvrp Datastreamsgvrp Documentation Data Quality Plots Citation DOI: 10.5439/1025199 [ What is this? ] Generate Citation ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Datastream : GVRP G-band (183 GHz) Vapor Radiometer profiler: 15 microwave brightness temperatures from 170.0 to 183.3 GHz Active Dates 2008.04.01 - 2014.01.09 Measurement Categories Radiometric Originating Instrument G-band (183 GHz) Vapor Radiometer Profiler (GVRP) Measurements Only measurements considered scientifically relevant are shown below by default. Show all measurements Measurement Units Variable Mean radiating temperature K MRT ( frequency ) Noise diode temperature at Tkbb = 290 K K Tnd ( frequency ) Non-linearity correction coefficient None alpha ( frequency )

71

VAPORIZATION THERMODYNAMICS OF KCl. COMBINING VAPOR PRESSURE AND GRAVIMETRIC DATA  

E-Print Network (OSTI)

.B. Department of Chemistry, Moscow State University, Moscow, 119899, Russia Bonnell D.W., Hastie J.W. National temperature chemistry situations, vapor pressures are typically less than 100 kPa. The molar volume is p = 101325 Pa). The subscript trs denotes that the changeisfor a transition, typically sublimation

Rudnyi, Evgenii B.

72

Partial Discharge Location using Unsynchronized Radiometer Network for Condition Monitoring in HV Substations - A Proposed Approach  

Science Journals Connector (OSTI)

A location estimation system for online Partial Discharge (PD) detection is proposed as a low-cost approach to real-time condition monitoring, asset management and operation optimization in future smart grid. Some early progress in the development of subsystems (specifically the antenna, radiometer device, PD emulator and PD generator) for a proof-of-principle prototype system is described. The proposed PD Wireless Sensor Network (WSN) uses a novel approach to PD location which obviates the need for synchronization between sensors thereby improving scalability.

J M R de Souza Neto (IEEE member); E C T de Macedo; J S da Rocha Neto (IEEE senior member); E G da Costa; S A Bhatti; I A Glover

2012-01-01T23:59:59.000Z

73

Macrocyclic polyaminocarboxylates for stable radiometal antibody conjugates for therapy, SPECT and PET imaging  

DOE Patents (OSTI)

A simple method for the synthesis of 1,4,7, 10-tetraazacyclododecane N,N{prime}N{double_prime},N{prime}{double_prime}-tetraacetic acid and 1,4,8,11-tetraazacyclotetradecane N,N{prime},N{double_prime},N{prime}{double_prime}-tetraacetic acid involves cyanomethylating 1,4,7,10-tetraazacyclododecane or 1,4,8,11-tetraazacyclotetradecane to form a tetranitrile and hydrolyzing the tetranitrile. These macrocyclic compounds are functionalized through one of the carboxylates and then conjugated to various biological molecules including monoclonal antibodies. The resulting conjugated molecules are labeled with radiometals for SPECT and PET imaging and for radiotherapy. 4 figs.

Mease, R.C.; Mausner, L.F.; Srivastava, S.C.

1997-06-17T23:59:59.000Z

74

Ground-Based and Airborne (PMS 2-D Probe Canister-Mounted) 183 GHz Water  

NLE Websites -- All DOE Office Websites (Extended Search)

Ground-Based and Airborne (PMS 2-D Probe Canister-Mounted) 183 GHz Water Ground-Based and Airborne (PMS 2-D Probe Canister-Mounted) 183 GHz Water Vapor Radiometer Pazmany, Andrew ProSensing Inc. Category: Instruments ProSensing Inc. has developed a G-band (183 GHz, 1.5 mm wavelength) water vapor radiometer (GVR) for the measurement of low concentrations of atmospheric water vapor and liquid water. The instrument's precipitable water vapor measurement precision is approximately 0.01 mm in dry (<2 mm vapor column) conditions. The ground-based version of the instrument was first deployed at ProSensing's facility in Amherst, MA in February 2005, then at the North Slope of Alaska DOE ARM site in Barrow AK in April 2005, where it has been continuously operating since. An airborne version, designed to operate from a standard PMS 2-D probe canister, is now being

75

Vacuum vapor deposition gun assembly  

DOE Patents (OSTI)

A vapor deposition gun assembly includes a hollow body having a cylindrical outer surface and an end plate for holding an adjustable heat sink, a hot hollow cathode gun, two magnets for steering the plasma from the gun into a crucible on the heat sink, and a shutter for selectively covering and uncovering the crucible.

Zeren, Joseph D. (Boulder, CO)

1985-01-01T23:59:59.000Z

76

LNG Vaporizer Utilizing Vacuum Steam Condensing  

Science Journals Connector (OSTI)

This report concerns the field test results of a new type of peak-shaving LNG vaporizer (VSV) whose heat source is ... heat of vacuum steam to vaporize and superheat LNG within heat transfer tubes. Prior to the.....

Y. Miyata; M. Hanamure; H. Kujirai; Y. Sato…

1991-01-01T23:59:59.000Z

77

Running-Film Vaporizer for LNG  

Science Journals Connector (OSTI)

Advances in welding technology and steel fabrication techniques have permitted the development of a new concept in cryogenic vaporizers—the running-film plate vaporizer. Although similar in heat transfer philosop...

H. H. West; G. L. Puckett

1975-01-01T23:59:59.000Z

78

Vapor Retarder Classification- Building America Top Innovation  

Energy.gov (U.S. Department of Energy (DOE))

This Building America Innovations profile describes research in vapor retarders. Since 2006 the IRC has permitted Class III vapor retarders like latex paint (see list above) in all climate zones under certain conditions thanks to research by Building America teams.

79

Vapor phase modifiers for oxidative coupling  

DOE Patents (OSTI)

Volatilized metal compounds retard vapor phase alkane conversion reactions in oxidative coupling processes that convert lower alkanes to higher hydrocarbons.

Warren, Barbara K. (Charleston, WV)

1991-01-01T23:59:59.000Z

80

Multi Spectral Pushbroom Imaging Radiometer (MPIR) for remote sensing cloud studies  

SciTech Connect

A Multi Spectral Pushbroom Imaging Radiometer (MPIR) has been developed as are relatively inexpensive ({approximately}$IM/copy), well-calibrated,imaging radiometer for aircraft studies of cloud properties. The instrument is designed to fly on an Unmanned Aerospace Vehicle (UAV) platform at altitudes from the surface up to 20 km. MPIR is being developed to support the Unmanned Aerospace Vehicle portion of the Department of Energy`s Atmospheric Radiation Measurements program (ARM/UAV). Radiation-cloud interactions are the dominant uncertainty in the current General Circulation Models used for atmospheric climate studies. Reduction of this uncertainty is a top scientific priority of the US Global Change Research Program and the ARM program. While the DOE`s ARM program measures a num-ber of parameters from the ground-based Clouds and Radiation Testbed sites, it was recognized from the outset that other key parameters are best measured by sustained airborne data taking. These measurements are critical in our understanding of global change issues as well as for improved atmospheric and near space weather forecasting applications.

Phipps, G.S.; Grotbeck, C.L.

1995-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Vapor Pressures and Heats of Vaporization of Primary Coal Tars  

Office of Scientific and Technical Information (OSTI)

/ PC92544-18 / PC92544-18 VAPOR PRESSURES AND HEATS OF VAPORIZATION OF PRIMARY COAL TARS FINAL REPORT Grant Dates: August, 1992 - November, 1996 Principal Authors: Eric M. Suuberg (PI) and Vahur Oja Report Submitted: April, 1997 Revised: July, 1997 Grant Number: DE-FG22-92PC92544 Report Submitted by: ERIC M. SUUBERG DIVISION OF ENGINEERING BROWN UNIVERSITY PROVIDENCE, RI 02912 TEL. (401) 863-1420 Prepared For: U. S. DEPT. OF ENERGY FEDERAL ENERGY TECHNOLOGY CENTER P.O. BOX 10940 PITTSBURGH, PA 15236 DR. KAMALENDU DAS, FETC, MORGANTOWN , WV TECHNICAL PROJECT OFFICER "US/DOE Patent Clearance is not required prior to the publication of this document" ii United States Government Disclaimer This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any

82

Retrieval of Optical And Size Parameters of Aerosols Utilizing a Multi-Filter Rotating Shadowband Radiometer and Inter-Comparison with CIMEL Sun Photometer and  

E-Print Network (OSTI)

Radiometer and Inter-Comparison with CIMEL Sun Photometer and MICROTOPS Sun Photometer Antonio Aguirre Radiometer (MFRSR) and comparing with data from a CIMEL Sun Photometer and a MICROTOPS Sun Photometer. Using the inverse cosine of the angle between the sun and the vertical. A Langley plot provides a linear regression

83

Vapor deposition of tantalum and tantalum compounds  

SciTech Connect

Tantalum, and many of its compounds, can be deposited as coatings with techniques ranging from pure, thermal chemical vapor deposition to pure physical vapor deposition. This review concentrates on chemical vapor deposition techniques. The paper takes a historical approach. The authors review classical, metal halide-based techniques and current techniques for tantalum chemical vapor deposition. The advantages and limitations of the techniques will be compared. The need for new lower temperature processes and hence new precursor chemicals will be examined and explained. In the last section, they add some speculation as to possible new, low-temperature precursors for tantalum chemical vapor deposition.

Trkula, M. [Los Alamos National Lab., NM (United States). Materials Science and Technology Div.

1996-04-01T23:59:59.000Z

84

Means and method for vapor generation  

DOE Patents (OSTI)

A liquid, in heat transfer contact with a surface heated to a temperature well above the vaporization temperature of the liquid, will undergo a multiphase (liquid-vapor) transformation from 0% vapor to 100% vapor. During this transition, the temperature driving force or heat flux and the coefficients of heat transfer across the fluid-solid interface, and the vapor percentage influence the type of heating of the fluid--starting as "feedwater" heating where no vapors are present, progressing to "nucleate" heating where vaporization begins and some vapors are present, and concluding with "film" heating where only vapors are present. Unstable heating between nucleate and film heating can occur, accompanied by possibly large and rapid temperature shifts in the structures. This invention provides for injecting into the region of potential unstable heating and proximate the heated surface superheated vapors in sufficient quantities operable to rapidly increase the vapor percentage of the multiphase mixture by perhaps 10-30% and thereby effectively shift the multiphase mixture beyond the unstable heating region and up to the stable film heating region.

Carlson, Larry W. (Oswego, IL)

1984-01-01T23:59:59.000Z

85

Validation of Satellite-Derived Liquid Water Paths Using ARM SGP Microwave Radiometers  

NLE Websites -- All DOE Office Websites (Extended Search)

Satellite-Derived Liquid Water Paths Using Satellite-Derived Liquid Water Paths Using ARM SGP Microwave Radiometers M. M. Khaiyer and J. Huang Analytical Services & Materials, Inc. Hampton, Virginia P. Minnis, B. Lin, and W. L. Smith, Jr. National Aeronautics and Space Administration Langley Research Center Hampton, Virginia A. Fan Science Applications International Corporation Hampton, Virginia A. Rapp Colorado State University Fort Collins, Colorado Introduction Satellites are useful for monitoring climatological parameters over large domains. They are especially useful for measuring various cloud microphysical and radiative parameters where ground-based instruments are not available. The geostationary operational environmental satellite (GOES) has been used to retrieve cloud and radiative properties over an extended domain centered on the Atmospheric

86

Modification of the collective Thomson scattering radiometer in the search for parametric decay on TEXTOR  

SciTech Connect

Strong scattering of high-power millimeter waves at 140 GHz has been shown to take place in heating and current-drive experiments at TEXTOR when a tearing mode is present in the plasma. The scattering signal is at present supposed to be generated by the parametric decay instability. Here we describe the heterodyne detection system used to characterize the newly discovered signal measured at TEXTOR, and we present spectral shapes in which the signal can appear under different conditions. The radiation is collected by the receiver through a quasi-optical transmission line that is independent of the electron cyclotron resonance heating transmission line, and so the scattering geometry is variable. The signal is detected with 42 frequency channels ranging from 136 to 142 GHz. We demonstrate that the large signal does not originate from gyrotron spurious radiation. The measured signal agrees well with independent backscattering radiometer data.

Nielsen, S. K.; Salewski, M.; Korsholm, S. B.; Leipold, F.; Meo, F.; Michelsen, P.; Stejner, M. [Association EURATOM - DTU, Department of Physics, Technical University of Denmark, Risoe Campus, DK-4000 Roskilde (Denmark); Bongers, W.; Moseev, D.; Westerhof, E. [FOM Institute DIFFER, Dutch Institute for Fundamental Energy Research, Association EURATOM - FOM, Nieuwegein (Netherlands); Oosterbeek, J. W. [Department of Applied Physics, Science and Technology of Nuclear Fusion, Eindhoven University of Technology, NL-5600 MB Eindhoven (Netherlands)

2012-11-15T23:59:59.000Z

87

Informal Preliminary Report on Comparisons of Prototype SPN-1 Radiometer to PARSL Measurements  

SciTech Connect

The prototype SPN-1 has been taking measurements for several months collocated with our PNNL Atmospheric Remote Sensing Laboratory (PARSL) solar tracker mounted instruments at the Pacific Northwest National Laboratory (PNNL) located in Richland, Washington, USA. The PARSL radiometers used in the following comparisons consist of an Eppley Normal Incident Pyrheliometer (NIP) and a shaded Eppley model 8-48 “Black and White” pyrgeometer (B&W) to measure the direct and diffuse shortwave irradiance (SW), respectively. These instruments were calibrated in mid-September by comparison to an absolute cavity radiometer directly traceable to the world standard group in Davos, Switzerland. The NIP calibration was determined by direct comparison, while the B&W was calibrated using the shade/unshade technique. All PARSL data prior to mid-September have been reprocessed using the new calibration factors. The PARSL data are logged as 1-minute averages from 1-second samples. Data used in this report span the time period from June 22 through December 1, 2006. All data have been processed through the QCRad code (Long and Shi, 2006), which itself is a more elaborately developed methodology along the lines of that applied by the Baseline Surface Radiation Network (BSRN) Archive (Long and Dutton, 2004), for quality control. The SPN-1 data are the standard total and diffuse SW values obtained from the analog data port of the instrument. The comparisons use only times when both the PARSL and SPN-1 data passed all QC testing. The data were further processed and analyzed by application of the SW Flux Analysis methodology (Long and Ackerman, 2000; Long and Gaustad, 2004, Long et al., 2006) to detect periods of clear skies, calculate continuous estimates of clear-sky SW irradiance and the effect of clouds on the downwelling SW, and estimate fractional sky cover.

Long, Charles N.

2014-06-17T23:59:59.000Z

88

Wick for metal vapor laser  

DOE Patents (OSTI)

An improved wick for a metal vapor laser is made of a refractory metal cylinder, preferably molybdenum or tungsten for a copper laser, which provides the wicking surface. Alternately, the inside surface of the ceramic laser tube can be metalized to form the wicking surface. Capillary action is enhanced by using wire screen, porous foam metal, or grooved surfaces. Graphite or carbon, in the form of chunks, strips, fibers or particles, is placed on the inside surface of the wick to reduce water, reduce metal oxides and form metal carbides.

Duncan, David B. (Livermore, CA)

1992-01-01T23:59:59.000Z

89

Non-Vapor Compression HVAC Technologies Report  

Energy.gov (U.S. Department of Energy (DOE))

While vapor-compression technologies have served heating, ventilation, and air-conditioning (HVAC) needs very effectively, and have been the dominant HVAC technology for close to 100 years, the conventional refrigerants used in vapor-compression equipment contribute to global climate change when released to the atmosphere. The Building Technologies Office is evaluating low-global warming potential (GWP) alternatives to vapor-compression technologies.

90

Mercury Vapor (Kooten, 1987) | Open Energy Information  

Open Energy Info (EERE)

Mercury Vapor (Kooten, 1987) Mercury Vapor (Kooten, 1987) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor (Kooten, 1987) Exploration Activity Details Location Unspecified Exploration Technique Mercury Vapor Activity Date Usefulness useful DOE-funding Unknown Notes Surface soil-mercury surveys are an inexpensive and useful exploration tool for geothermal resources. ---- Surface geochemical surveys for mercury were conducted in 16 areas in 1979-1981 by ARCO Oil and Gas Company as part of its geothermal evaluation program. Three techniques used together have proved satisfactory in evaluating surface mercury data. These are contouring, histograms and cumulative frequency plots of the data. Contouring geochemical data and constructing histograms are standard

91

Vapor phase modifiers for oxidative coupling  

DOE Patents (OSTI)

Volatilized metal compounds are described which are capable of retarding vapor phase alkane conversion reactions in oxidative coupling processes that convert lower alkanes to higher hydrocarbons.

Warren, B.K.

1991-12-17T23:59:59.000Z

92

Near real time vapor detection and enhancement using aerosol adsorption  

SciTech Connect

A vapor sample detection method where the vapor sample contains vapor and ambient air and surrounding natural background particles. The vapor sample detection method includes the steps of generating a supply of aerosol that have a particular effective median particle size, mixing the aerosol with the vapor sample forming aerosol and adsorbed vapor suspended in an air stream, impacting the suspended aerosol and adsorbed vapor upon a reflecting element, alternatively directing infrared light to the impacted aerosol and adsorbed vapor, detecting and analyzing the alternatively directed infrared light in essentially real time using a spectrometer and a microcomputer and identifying the vapor sample.

Novick, Vincent J.; Johnson, Stanley A.

1997-12-01T23:59:59.000Z

93

Near real time vapor detection and enhancement using aerosol adsorption  

DOE Patents (OSTI)

A vapor sample detection method is described where the vapor sample contains vapor and ambient air and surrounding natural background particles. The vapor sample detection method includes the steps of generating a supply of aerosol that have a particular effective median particle size, mixing the aerosol with the vapor sample forming aerosol and adsorbed vapor suspended in an air stream, impacting the suspended aerosol and adsorbed vapor upon a reflecting element, alternatively directing infrared light to the impacted aerosol and adsorbed vapor, detecting and analyzing the alternatively directed infrared light in essentially real time using a spectrometer and a microcomputer and identifying the vapor sample. 13 figs.

Novick, V.J.; Johnson, S.A.

1999-08-03T23:59:59.000Z

94

Near real time vapor detection and enhancement using aerosol adsorption  

DOE Patents (OSTI)

A vapor sample detection method where the vapor sample contains vapor and ambient air and surrounding natural background particles. The vapor sample detection method includes the steps of generating a supply of aerosol that have a particular effective median particle size, mixing the aerosol with the vapor sample forming aerosol and adsorbed vapor suspended in an air stream, impacting the suspended aerosol and adsorbed vapor upon a reflecting element, alternatively directing infrared light to the impacted aerosol and adsorbed vapor, detecting and analyzing the alternatively directed infrared light in essentially real time using a spectrometer and a microcomputer and identifying the vapor sample.

Novick, Vincent J. (Downers Grove, IL); Johnson, Stanley A. (Countryside, IL)

1999-01-01T23:59:59.000Z

95

Quantitative organic vapor-particle sampler  

DOE Patents (OSTI)

A quantitative organic vapor-particle sampler for sampling semi-volatile organic gases and particulate components. A semi-volatile organic reversible gas sorbent macroreticular resin agglomerates of randomly packed microspheres with the continuous porous structure of particles ranging in size between 0.05-10 .mu.m for use in an integrated diffusion vapor-particle sampler.

Gundel, Lara (Berkeley, CA); Daisey, Joan M. (Walnut Creek, CA); Stevens, Robert K. (Cary, NC)

1998-01-01T23:59:59.000Z

96

LNG fire and vapor control system technologies  

SciTech Connect

This report provides a review of fire and vapor control practices used in the liquefied natural gas (LNG) industry. Specific objectives of this effort were to summarize the state-of-the-art of LNG fire and vapor control; define representative LNG facilities and their associated fire and vapor control systems; and develop an approach for a quantitative effectiveness evaluation of LNG fire and vapor control systems. In this report a brief summary of LNG physical properties is given. This is followed by a discussion of basic fire and vapor control design philosophy and detailed reviews of fire and vapor control practices. The operating characteristics and typical applications and application limitations of leak detectors, fire detectors, dikes, coatings, closed circuit television, communication systems, dry chemicals, water, high expansion foam, carbon dioxide and halogenated hydrocarbons are described. Summary descriptions of a representative LNG peakshaving facility and import terminal are included in this report together with typical fire and vapor control systems and their locations in these types of facilities. This state-of-the-art review identifies large differences in the application of fire and vapor control systems throughout the LNG industry.

Konzek, G.J.; Yasutake, K.M.; Franklin, A.L.

1982-06-01T23:59:59.000Z

97

Remotely Controlled, Continuous Observations of Infrared Radiance with the CSIRO/ARM Mark II Radiometer at the SGP CART Site  

NLE Websites -- All DOE Office Websites (Extended Search)

Remotely Controlled, Continuous Observations of Remotely Controlled, Continuous Observations of Infrared Radiance with the CSIRO/ARM Mark II Radiometer at the SGP CART Site C. M. R. Platt and R. T. Austin Department of Atmospheric Science Colorado State University Fort Collins, Colorado C. M. R. Platt and J. A. Bennett Commonwealth Scientific and Industrial Research Organization Atmospheric Research Aspendale, Victoria, Australia Abstract The Commonwealth Scientific and Industrial Research Organization/Atmospheric Radiation Measurement (CSIRO/ARM) Program Mark II infrared (IR) filter radiometer operated continuously at the Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site for a period of five weeks. Data of high quality were obtained by remote operation and data transfer with no evidence of spurious

98

Comparison of Historical Satellite-Based Estimates of Solar Radiation Resources with Recent Rotating Shadowband Radiometer Measurements: Preprint  

SciTech Connect

The availability of rotating shadow band radiometer measurement data at several new stations provides an opportunity to compare historical satellite-based estimates of solar resources with measurements. We compare mean monthly daily total (MMDT) solar radiation data from eight years of NSRDB and 22 years of NASA hourly global horizontal and direct beam solar estimates with measured data from three stations, collected after the end of the available resource estimates.

Myers, D. R.

2009-03-01T23:59:59.000Z

99

A reactionless, bearingless linear shutter mechanism for the multispectral pushbroom imaging radiometer  

SciTech Connect

The Atmospheric Radiation Measurement Program is a multi-laboratory, interagency program as part of DOE`s principal entry into the US Global Change Research Program. Two issues addressed are the radiation budget and its spectral dependence, and radiative and other properties of clouds. Measures of solar flux divergence and energy exchanges between clouds, the earth, its oceans, and the atmosphere through various altitudes are sought. Additionally, the program seeks to provide measurements to calibrate satellite radiance products and validate their associated flux retrieval algorithms. Unmanned Aerospace Vehicles fly long, extended missions. MPIR is one of the primary instruments on the ARM-UAV campaigns. A shutter mechanism has been developed and flown as part of an airborne imaging radiometer having application to spacecraft or other applications requiring low vibration, high reliability, and long life. The device could be employed in other cases where a reciprocating platform is needed. Typical shutters and choppers utilize a spinning disc, or in very small instruments, a vibrating vane to continually interrupt incident light or radiation that enters the system. A spinning disk requires some sort of bearings that usually have limited life, and at a minimum introduce issues of reliability. Friction, lubrication and contamination always remain critical areas of concern, as well as the need for power to operate. Dual vibrating vanes may be dynamically well balanced as a set and are frictionless. However, these are limited by size in a practical sense. In addition, multiples of these devices are difficult to synchronize.

Krumel, L.J.

1996-12-31T23:59:59.000Z

100

Energy balance in laser-irradiated vaporizing droplets  

Science Journals Connector (OSTI)

The interactions of vaporizing aerosols with a high energy laser beam are analyzed in the diffusive vaporization regime. This is the regime in which diffusive mass transport and...

Zardecki, Andrew; Armstrong, Robert L

1988-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Ground Gravity Survey At Cove Fort Area - Vapor (Warpinski, Et...  

Open Energy Info (EERE)

Vapor (Warpinski, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Cove Fort Area - Vapor (Warpinski, Et...

102

Hydrogen-Bond Acidic Polymers for Chemical Vapor Sensing. | EMSL  

NLE Websites -- All DOE Office Websites (Extended Search)

Acidic Polymers for Chemical Vapor Sensing. Hydrogen-Bond Acidic Polymers for Chemical Vapor Sensing. Abstract: A review with 171 references. Hydrogen-bond acidic polymers for...

103

Recovering hydrocarbons from hydrocarbon-containing vapors  

DOE Patents (OSTI)

Values are recovered from a hydrocarbon-containing vapor by contacting the vapor with quench liquid consisting essentially of hydrocarbons to form a condensate and a vapor residue, the condensate and quench fluid forming a combined liquid stream. The combined liquid stream is mixed with a viscosity-lowering liquid to form a mixed liquid having a viscosity lower than the viscosity of the combined liquid stream to permit easy handling of the combined liquid stream. The quench liquid is a cooled portion of the mixed liquid. Viscosity-lowering liquid is separated from a portion of the mixed liquid and cycled to form additional mixed liquid.

Mirza, Zia I. (La Verne, CA); Knell, Everett W. (Los Alamitos, CA); Winter, Bruce L. (Danville, CA)

1980-09-30T23:59:59.000Z

104

The R/V Discoverer cruise to Manus Island. The BNL Portable Radiometer Package (PRP) evaluation  

SciTech Connect

Brookhaven National Laboratory installed and operated a Portable Radiation Package (PRP) on the NOAA ship R/V DISCOVERER as part of the Combined Sensor Program cruise in the Tropical Western Pacific Ocean. The DISCOVERER transported a collection of radiation and atmospheric instrumentation to positions offshore of manus Island to compare cloud and radiation fields to like instruments measured from a station on the island. The ship sailed NW from Pago Pago, American Samoa, on 14 March 1996 to a latitude of 1{degree}S then due West until it approached manus Island (2{degree}S and 148{degree}E) on approximately 7 April. The ship then turned SW and approached Manus Island in three steps. This route was reversed during the ship`s return to Hawaii. The PRP package is a compact low-power integration of simple sensors that measure long- and short-wave irradiance from moving platforms. A rapid rotating shadowband radiometer that is designed to provide good estimates of diffuse (sky) radiation even from moving buoys or ships was being evaluated. The PRP provided the only means of making diffuse (sky) radiation measurements from the ship. The CSP cruise provided an excellent opportunity to intercompare the PRP with other like instruments in the TWP locale. The unit was located on the starboard flying bridge which was fully exposed to direct sunlight during the ship`s westward transit. When the ship was at its closest approach to manus, the PRP was moved to the island where careful intercomparison with the Manus instrumentation was conducted.

Reynolds, R.M.; Smith, S.

1996-05-24T23:59:59.000Z

105

Aerogel composites using chemical vapor infiltration  

NLE Websites -- All DOE Office Websites (Extended Search)

Aerogel composites using chemical vapor infiltration Aerogel composites using chemical vapor infiltration Title Aerogel composites using chemical vapor infiltration Publication Type Journal Article Year of Publication 1995 Authors Hunt, Arlon J., Michael R. Ayers, and Wanqing Cao Journal Journal of Non-Crystalline Solids Volume 185 Pagination 227-232 Abstract A new method to produce novel composite materials based on the use of aerogels as a starting material is described. Using chemical vapor infiltration, a variety of solid materials were thermally deposited into the open pore structure of aerogel. The resulting materials possess new and unusual properties including photoluminescence, magnetism and altered optical properties. An important characteristic of this preparation process is the very small size of the deposits that gives rise to new behaviors. Silicon deposits exhibit photoluminescence, indicating quantum confinement. Two or more phases may be deposited simultaneously and one or both chemically or thermally reacted to produce new structures.

106

Chemical vapor detection using nanomechanical platform  

Science Journals Connector (OSTI)

For high sensitive and multiplexed chemical analysis, an opto-mechanical detection platform has been built. To check the performance of the platform, we performed water vapor response measurements for ... sensors...

S. H. Lim

2007-11-01T23:59:59.000Z

107

Chemical vapor deposition of functionalized isobenzofuran polymers  

E-Print Network (OSTI)

This thesis develops a platform for deposition of polymer thin films that can be further tailored by chemical surface modification. First, we explore chemical vapor deposition of functionalized isobenzofuran films using ...

Olsson, Ylva Kristina

2007-01-01T23:59:59.000Z

108

Vapor Power Systems MAE 4263 Final Exam  

E-Print Network (OSTI)

Vapor Power Systems MAE 4263 Final Exam Wednesday, May 5, 2004 Prof. P.M. Moretti Key Instructions, then think, then write! 1. What is the dewpoint of the exhaust of your car, if the gasoline consists2 so that the mole fraction of water vapor is yH2 O = 9 9 + 8 + 47 = 0:14063 pH2 O = 0:14063 14

109

Optical monitor for water vapor concentration  

DOE Patents (OSTI)

A system for measuring and monitoring water vapor concentration in a sample uses as a light source an argon discharge lamp, which inherently emits light with a spectral line that is close to a water vapor absorption line. In a preferred embodiment, the argon line is split by a magnetic field parallel to the direction of light propagation from the lamp into sets of components of downshifted and upshifted frequencies of approximately 1575 Gauss. The downshifted components are centered on a water vapor absorption line and are thus readily absorbed by water vapor in the sample; the upshifted components are moved away from that absorption line and are minimally absorbed. A polarization modulator alternately selects the upshifted components or downshifted components and passes the selected components to the sample. After transmission through the sample, the transmitted intensity of a component of the argon line varies as a result of absorption by the water vapor. The system then determines the concentration of water vapor in the sample based on differences in the transmitted intensity between the two sets of components. In alternative embodiments alternate selection of sets of components is achieved by selectively reversing the polarity of the magnetic field or by selectively supplying the magnetic field to the emitting plasma. 5 figs.

Kebabian, P.

1998-06-02T23:59:59.000Z

110

Optical monitor for water vapor concentration  

DOE Patents (OSTI)

A system for measuring and monitoring water vapor concentration in a sample uses as a light source an argon discharge lamp, which inherently emits light with a spectral line that is close to a water vapor absorption line. In a preferred embodiment, the argon line is split by a magnetic field parallel to the direction of light propagation from the lamp into sets of components of downshifted and upshifted frequencies of approximately 1575 Gauss. The downshifted components are centered on a water vapor absorption line and are thus readily absorbed by water vapor in the sample; the upshifted components are moved away from that absorption line and are minimally absorbed. A polarization modulator alternately selects the upshifted components or downshifted components and passes the selected components to the sample. After transmission through the sample, the transmitted intensity of a component of the argon line varies as a result of absorption by the water vapor. The system then determines the concentration of water vapor in the sample based on differences in the transmitted intensity between the two sets of components. In alternative embodiments alternate selection of sets of components is achieved by selectively reversing the polarity of the magnetic field or by selectively supplying the magnetic field to the emitting plasma.

Kebabian, Paul (Acton, MA)

1998-01-01T23:59:59.000Z

111

Results of First Outdoor Comparison Between Absolute Cavity Pyrgeometer (ACP) and Infrared Integrating Sphere (IRIS) Radiometer at PMOD (Presentation)  

SciTech Connect

The ACP and IRIS are developed to establish a world reference for calibrating pyrgeometers with traceability to SI units. The two radiometers are unwindowed with negligible spectral dependence, and traceable to SI units through the temperature scale (ITS-90). The first outdoor comparison between the two designs was held from January 28 to February 8, 2013 at the Physikalisch-Metorologisches Observatorium Davos (PMOD). The difference between the irradiance measured by ACP and that of IRIS was within 1 W/m2. A difference of 5 W/m2 was observed between the irradiance measured by ACP&IRIS and that of the interim World Infrared Standard Group (WISG).

Reda, I.; Grobner, J.; Wacker, S.; Stoffel, T.

2013-03-01T23:59:59.000Z

112

Synthesis of macrocyclic polyaminocarboxylates and their use for preparing stable radiometal antibody immunoconjugates for therapy, SPECT and PET imaging  

DOE Patents (OSTI)

A simple method for the synthesis of 1,4,7,10-tetraazacyclododecane N,N{prime}N{double_prime},N{prime}{double_prime}-tetraacetic acid and 1,4,8,11-tetraazacyclotetradecane N,N{prime},N{double_prime},N{prime}{double_prime}-tetraacetic acid involves cyanomethylating 1,4,7,10-tetraazacyclododecane or 1,4,8,11-tetraazacyclotetradecane to form a tetranitrile and hydrolyzing the tetranitrile. These macrocyclic compounds are functionalized through one of the carboxylates and then conjugated to various biological molecules including monoclonal antibodies. The resulting conjugated molecules are labeled with radiometals for SPECT and PET imaging and for radiotherapy. 4 figs.

Mease, R.C.; Mausner, L.F.; Srivastava, S.C.

1995-06-27T23:59:59.000Z

113

Vapor Pressures and Vaporization, Sublimation, and Fusion Enthalpies of Some Fatty Acids  

E-Print Network (OSTI)

Vapor Pressures and Vaporization, Sublimation, and Fusion Enthalpies of Some Fatty Acids Joe A. Wilson and James S. Chickos* Department of Chemistry and Biochemistry, University of MissouriSt. Louis, St. Louis, Missouri 63121, United States *S Supporting Information ABSTRACT: Sublimation enthalpies

Chickos, James S.

114

Vapor Pressures and Vaporization Enthalpies of a Series of Dialkyl Phthalates by Correlation Gas Chromatography  

E-Print Network (OSTI)

Chromatography Chase Gobble and James Chickos* Department of Chemistry and Biochemistry University of Missouri-St. Louis, St. Louis Missouri 63121, United States Sergey P. Verevkin Department of Physical Chemistry: Experimental vapor pressures, vaporization, fusion and sublimation enthalpies of a number of dialkyl

Chickos, James S.

115

ARM - Midlatitude Continental Convective Clouds Microwave Radiometer Profiler (jensen-mwr)  

SciTech Connect

A major component of the Mid-latitude Continental Convective Clouds Experiment (MC3E) field campaign was the deployment of an enhanced radiosonde array designed to capture the vertical profile of atmospheric state variables (pressure, temperature, humidity wind speed and wind direction) for the purpose of deriving the large-scale forcing for use in modeling studies. The radiosonde array included six sites (enhanced Central Facility [CF-1] plus five new sites) launching radiosondes at 3-6 hour sampling intervals. The network will cover an area of approximately (300)2 km2 with five outer sounding launch sites and one central launch location. The five outer sounding launch sites are: S01 Pratt, KS [ 37.7oN, 98.75oW]; S02 Chanute, KS [37.674, 95.488]; S03 Vici, Oklahoma [36.071, -99.204]; S04 Morris, Oklahoma [35.687, -95.856]; and S05 Purcell, Oklahoma [34.985, -97.522]. Soundings from the SGP Central Facility during MC3E can be retrieved from the regular ARM archive. During routine MC3E operations 4 radiosondes were launched from each of these sites (approx. 0130, 0730, 1330 and 1930 UTC). On days that were forecast to be convective up to four additional launches were launched at each site (approx. 0430, 1030, 1630, 2230 UTC). There were a total of approximately 14 of these high frequency launch days over the course of the experiment. These files contain brightness temperatures observed at Purcell during MC3E. The measurements were made with a 5 channel (22.235, 23.035, 23.835, 26.235, 30.000GHz) microwave radiometer at one minute intervals. The results have been separated into daily files and the day of observations is indicated in the file name. All observations were zenith pointing. Included in the files are the time variables base_time and time_offset. These follow the ARM time conventions. Base_time is the number seconds since January 1, 1970 at 00:00:00 for the first data point of the file and time_offset is the offset in seconds from base_time.

Jensen, Mike

2012-02-01T23:59:59.000Z

116

Failure and Redemption of Multifilter Rotating Shadowband Radiometer (MFRSR)/Normal Incidence Multifilter Radiometer (NIMFR) Cloud Screening: Contrasting Algorithm Performance at Atmospheric Radiation Measurement (ARM) North Slope of Alaska (NSA) and Southern Great Plains (SGP) Sites  

SciTech Connect

Well-known cloud-screening algorithms, which are designed to remove cloud-contaminated aerosol optical depths (AOD) from AOD measurements, have shown great performance at many middle-to-low latitude sites around the world. However, they may occasionally fail under challenging observational conditions, such as when the sun is low (near the horizon) or when optically thin clouds with small spatial inhomogeneity occur. Such conditions have been observed quite frequently at the high-latitude Atmospheric Radiation Measurement (ARM) North Slope of Alaska (NSA) sites. A slightly modified cloud-screening version of the standard algorithm is proposed here with a focus on the ARM-supported Multifilter Rotating Shadowband Radiometer (MFRSR) and Normal Incidence Multifilter Radiometer (NIMFR) data. The modified version uses approximately the same techniques as the standard algorithm, but it additionally examines the magnitude of the slant-path line of sight transmittance and eliminates points when the observed magnitude is below a specified threshold. Substantial improvement of the multi-year (1999-2012) aerosol product (AOD and its Angstrom exponent) is shown for the NSA sites when the modified version is applied. Moreover, this version reproduces the AOD product at the ARM Southern Great Plains (SGP) site, which was originally generated by the standard cloud-screening algorithms. The proposed minor modification is easy to implement and its application to existing and future cloud-screening algorithms can be particularly beneficial for challenging observational conditions.

Kassianov, Evgueni I.; Flynn, Connor J.; Koontz, Annette S.; Sivaraman, Chitra; Barnard, James C.

2013-09-11T23:59:59.000Z

117

ARM - Field Campaign - Water Vapor IOP  

NLE Websites -- All DOE Office Websites (Extended Search)

govCampaignsWater Vapor IOP govCampaignsWater Vapor IOP Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : Water Vapor IOP 1996.09.10 - 1996.09.30 Lead Scientist : Henry Revercomb For data sets, see below. Summary SCHEDULE This IOP will be conducted from September 10 - 30, 1996 (coincident with the Fall ARM-UAV IOP). Instruments that do not require supervision will be operated continuously during this period. Instruments that do require supervision are presently planned to be operated for 8-hour periods each day. Because it is necessary to cover as broad a range of environmental conditions as possible, the daily 8-hour period will be shifted across the diurnal cycle as deemed appropriate during the IOP (but will be maintained as a contiguous 8-hour block).

118

atmospheric water vapor | OpenEI  

Open Energy Info (EERE)

atmospheric water vapor atmospheric water vapor Dataset Summary Description (Abstract): Monthly Average Solar Resource for 2-axis tracking concentrating collectors for Mexico, Central America, and the Caribbean Islands. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to a concentrating collector, such as a dish collector, which tracks the sun continuously. Source NREL Date Released July 31st, 2006 (8 years ago) Date Updated October 30th, 2007 (7 years ago) Keywords atmospheric water vapor Carribean Islands Central America DNI GIS Mexico NREL GEF solar SWERA UNEP Data application/zip icon Download Shapefile (zip, 247.8 KiB) text/csv icon Download Data (csv, 370.6 KiB) Quality Metrics Level of Review Some Review

119

atmoshperic water vapor | OpenEI  

Open Energy Info (EERE)

atmoshperic water vapor atmoshperic water vapor Dataset Summary Description (Abstract): Monthly Average Solar Resource for flat-plate collectors tilted at latitude for China. Source NREL Date Released April 12th, 2005 (9 years ago) Date Updated October 30th, 2007 (7 years ago) Keywords atmoshperic water vapor China GEF GIS NREL solar SWERA TILT UNEP Data application/zip icon Download Shapefile (zip, 625.6 KiB) text/csv icon Download Data (csv, 704.1 KiB) Quality Metrics Level of Review Some Review Comment Temporal and Spatial Coverage Frequency Time Period 01/01/1985 - 12/31/1991 License License Open Data Commons Public Domain Dedication and Licence (PDDL) Comment Rate this dataset Usefulness of the metadata Average vote Your vote Usefulness of the dataset Average vote Your vote Ease of access

120

Vapor characterization of Tank 241-C-103  

SciTech Connect

The Westinghouse Hanford Company Tank Vapor Issue Resolution Program has developed, in cooperation with Northwest Instrument Systems, Inc., Oak Ridge National Laboratory, Oregon Graduate Institute of Science and Technology, Pacific Northwest Laboratory, and Sandia National Laboratory, the equipment and expertise to characterize gases and vapors in the high-level radioactive waste storage tanks at the Hanford Site in south central Washington State. This capability has been demonstrated by the characterization of the tank 241-C-103 headspace. This tank headspace is the first, and for many reasons is expected to be the most problematic, that will be characterized (Osborne 1992). Results from the most recent and comprehensive sampling event, sample job 7B, are presented for the purpose of providing scientific bases for resolution of vapor issues associated with tank 241-C-103. This report is based on the work of Clauss et al. 1994, Jenkins et al. 1994, Ligotke et al. 1994, Mahon et al. 1994, and Rasmussen and Einfeld 1994. No attempt has been made in this report to evaluate the implications of the data presented, such as the potential impact of headspace gases and vapors to tank farm workers health. That and other issues will be addressed elsewhere. Key to the resolution of worker health issues is the quantitation of compounds of toxicological concern. The Toxicology Review Panel, a panel of Pacific Northwest Laboratory experts in various areas, of toxicology, has chosen 19 previously identified compounds as being of potential toxicological concern. During sample job 7B, the sampling and analytical methodology was validated for this preliminary list of compounds of toxicological concern. Validation was performed according to guidance provided by the Tank Vapor Conference Committee, a group of analytical chemists from academic institutions and national laboratories assembled and commissioned by the Tank Vapor Issue Resolution Program.

Huckaby, J.L. [Westinghouse Hanford Co., Richland, WA (United States); Story, M.S. [Northwest Instrument Systems, Inc. Richland, WA (United States)

1994-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Thermal electric vapor trap arrangement and method  

DOE Patents (OSTI)

A technique for trapping vapor within a section of a tube is disclosed herein. This technique utilizes a conventional, readily providable thermal electric device having a hot side and a cold side and means for powering the device to accomplish this. The cold side of this device is positioned sufficiently close to a predetermined section of the tube and is made sufficiently cold so that any condensable vapor passing through the predetermined tube section is condensed and trapped, preferably within the predetermined tube section itself. 4 figs.

Alger, T.

1988-03-15T23:59:59.000Z

122

Diode pumped alkali vapor fiber laser  

DOE Patents (OSTI)

A method and apparatus is provided for producing near-diffraction-limited laser light, or amplifying near-diffraction-limited light, in diode pumped alkali vapor photonic-band-gap fiber lasers or amplifiers. Laser light is both substantially generated and propagated in an alkali gas instead of a solid, allowing the nonlinear and damage limitations of conventional solid core fibers to be circumvented. Alkali vapor is introduced into the center hole of a photonic-band-gap fiber, which can then be pumped with light from a pump laser and operated as an oscillator with a seed beam, or can be configured as an amplifier.

Payne, Stephen A. (Castro Valley, CA); Beach, Raymond J. (Livermore, CA); Dawson, Jay W. (Livermore, CA); Krupke, William F. (Pleasanton, CA)

2006-07-26T23:59:59.000Z

123

Diode pumped alkali vapor fiber laser  

DOE Patents (OSTI)

A method and apparatus is provided for producing near-diffraction-limited laser light, or amplifying near-diffraction-limited light, in diode pumped alkali vapor photonic-band-gap fiber lasers or amplifiers. Laser light is both substantially generated and propagated in an alkali gas instead of a solid, allowing the nonlinear and damage limitations of conventional solid core fibers to be circumvented. Alkali vapor is introduced into the center hole of a photonic-band-gap fiber, which can then be pumped with light from a pump laser and operated as an oscillator with a seed beam, or can be configured as an amplifier.

Payne, Stephen A. (Castro Valley, CA); Beach, Raymond J. (Livermore, CA); Dawson, Jay W. (Livermore, CA); Krupke, William F. (Pleasanton, CA)

2007-10-23T23:59:59.000Z

124

Environmental Chemistry at Vapor/Water Interfaces  

E-Print Network (OSTI)

Environmental Chemistry at Vapor/Water Interfaces: Insights from Vibrational Sum Frequency Generation Spectroscopy Aaron M. Jubb, Wei Hua, and Heather C. Allen Department of Chemistry, The Ohio State/0505-0107$20.00 Keywords salts, lipids, atmospheric chemistry, ion binding, oxidation Abstract The chemistry that occurs

125

Advancing Explosives Detection Capabilities: Vapor Detection  

ScienceCinema (OSTI)

A new, PNNL-developed method provides direct, real-time detection of trace amounts of explosives such as RDX, PETN and C-4. The method selectively ionizes a sample before passing the sample through a mass spectrometer to detect explosive vapors. The method could be used at airports to improve aviation security.

Atkinson, David

2014-07-24T23:59:59.000Z

126

Program performs vapor-liquid equilibrium calculations  

SciTech Connect

A program designed for the Hewlett-Packard HP-41CV or 41C calculators solves basic vapor-liquid equilibrium problems, including figuring the dewpoint, bubblepoint, and equilibrium flash. The algorithm uses W.C. Edmister's method for predicting ideal-solution K values.

Rice, V.L.

1982-06-28T23:59:59.000Z

127

Synchroton X-Ray Studies of Liquid-Vapor Interfaces  

Science Journals Connector (OSTI)

The variation of density across the liquid-vapor interface from essentially zero density far out in the vapor phase to a homogeneous density deep in the liquid phase can be determined by X-ray reflectivity mea...

J. Als-Nielsen

1988-01-01T23:59:59.000Z

128

Vapor intrusion modeling : limitations, improvements, and value of information analyses  

E-Print Network (OSTI)

Vapor intrusion is the migration of volatile organic compounds (VOCs) from a subsurface source into the indoor air of an overlying building. Vapor intrusion models, including the Johnson and Ettinger (J&E) model, can be ...

Friscia, Jessica M. (Jessica Marie)

2014-01-01T23:59:59.000Z

129

Estimating the Atmospheric Water Vapor Content from Sun Photometer Measurements  

Science Journals Connector (OSTI)

The differential absorption technique for estimating columnar water vapor values from the analysis of sunphotometric measurements with wide- and narrowband interferential filters centered near 0.94 ?m is discussed and adapted. Water vapor line ...

Artemio Plana-Fattori; Michel Legrand; Didier Tanré; Claude Devaux; Anne Vermeulen; Philippe Dubuisson

1998-08-01T23:59:59.000Z

130

OPTIMIZATION OF INJECTION INTO VAPOR-DOMINATED GEOTHERMAL  

E-Print Network (OSTI)

given by U.S. Department of Energy, Geothermal Division. #12;vii Table of Contents ABSTRACTOPTIMIZATION OF INJECTION INTO VAPOR-DOMINATED GEOTHERMAL RESERVOIRS CONSIDERING ADSORPTION governing the behavior of vapor- dominated geothermal reservoirs. These mechanisms affect both

Stanford University

131

Validation of Geolocation of Measurements of the Clouds and the Earth’s Radiant Energy System (CERES) Scanning Radiometers aboard Three Spacecraft  

Science Journals Connector (OSTI)

The Clouds and the Earth’s Radiant Energy System (CERES) instrument is a scanning radiometer for measuring Earth-emitted and -reflected solar radiation to understand Earth’s energy balance. One CERES instrument was placed into orbit aboard the ...

G. Louis Smith; Kory J. Priestley; Phillip C. Hess; Chris Currey; Peter Spence

2009-11-01T23:59:59.000Z

132

Apparent Temperature Dependence on Localized Atmospheric Water Vapor  

E-Print Network (OSTI)

Apparent Temperature Dependence on Localized Atmospheric Water Vapor Matthew Montanaroa, Carl), hence water vapor is the primary constituent of concern. The tower generates a localized water vapor, Office B108, Aiken, SC, USA ABSTRACT The atmosphere is a critical factor in remote sensing. Radiance from

Salvaggio, Carl

133

Advanced Membrane Systems: Recovering Wasteful and Hazardous Fuel Vapors at the Gasoline Tank  

Energy.gov (U.S. Department of Energy (DOE))

Case study covering Compact Membrane Systems, Inc. and its membrane vapor processor that recovers fuel vapors from gasoline refueling.

134

Precision micro drilling with copper vapor lasers  

SciTech Connect

The authors have developed a copper vapor laser based micro machining system using advanced beam quality control and precision wavefront tilting technologies. Micro drilling has been demonstrated through percussion drilling and trepanning using this system. With a 30 W copper vapor laser running at multi-kHz pulse repetition frequency, straight parallel holes with size varying from 500 microns to less than 25 microns and with aspect ratio up to 1:40 have been consistently drilled on a variety of metals with good quality. For precision trepanned holes, the hole-to-hole size variation is typically within 1% of its diameter. Hole entrance and exit are both well defined with dimension error less than a few microns. Materialography of sectioned holes shows little (sub-micron scale) recast layer and heat affected zone with surface roughness within 1--2 microns.

Chang, J.J.; Martinez, M.W.; Warner, B.E.; Dragon, E.P.; Huete, G.; Solarski, M.E.

1994-09-02T23:59:59.000Z

135

Copper vapor laser modular packaging assembly  

DOE Patents (OSTI)

A modularized packaging arrangement for one or more copper vapor lasers and associated equipment is disclosed herein. This arrangement includes a single housing which contains the laser or lasers and all their associated equipment except power, water and neon, and means for bringing power, water, and neon which are necessary to the operation of the lasers into the container for use by the laser or lasers and their associated equipment.

Alger, Terry W. (Tracy, CA); Ault, Earl R. (Dublin, CA); Moses, Edward I. (Castro Valley, CA)

1992-01-01T23:59:59.000Z

136

ARM - Field Campaign - Fall 1997 Water Vapor IOP  

NLE Websites -- All DOE Office Websites (Extended Search)

Water Vapor IOP Water Vapor IOP Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : Fall 1997 Water Vapor IOP 1997.09.15 - 1997.10.05 Lead Scientist : Henry Revercomb For data sets, see below. Summary The Water Vapor IOP was conducted as a follow-up to a predecessor IOP on water vapor held in September 1996. This IOP relied heavily on both ground-based guest and CART instrumentation and in-situ aircraft and tethered sonde/kite measurements. Primary operational hours were from 6 p.m. Central until at least midnight, with aircraft support normally from about 9 p.m. until midnight when available. However, many daytime measurements were made to support this IOP. The first Water Vapor IOP primarily concentrated on the atmosphere's lowest

137

Vapor port and groundwater sampling well  

DOE Patents (OSTI)

A method and apparatus has been developed for combining groundwater monitoring wells with unsaturated-zone vapor sampling ports. The apparatus allows concurrent monitoring of both the unsaturated and the saturated zone from the same well at contaminated areas. The innovative well design allows for concurrent sampling of groundwater and volatile organic compounds (VOCs) in the vadose (unsaturated) zone from a single well, saving considerable time and money. The sample tubes are banded to the outer well casing during installation of the well casing.

Hubbell, Joel M. (Idaho Falls, ID); Wylie, Allan H. (Idaho Falls, ID)

1996-01-01T23:59:59.000Z

138

Chemical vapor deposition of epitaxial silicon  

DOE Patents (OSTI)

A single chamber continuous chemical vapor deposition (CVD) reactor is described for depositing continuously on flat substrates, for example, epitaxial layers of semiconductor materials. The single chamber reactor is formed into three separate zones by baffles or tubes carrying chemical source material and a carrier gas in one gas stream and hydrogen gas in the other stream without interaction while the wafers are heated to deposition temperature. Diffusion of the two gas streams on heated wafers effects the epitaxial deposition in the intermediate zone and the wafers are cooled in the final zone by coolant gases. A CVD reactor for batch processing is also described embodying the deposition principles of the continuous reactor.

Berkman, Samuel (Florham Park, NJ)

1984-01-01T23:59:59.000Z

139

Storing images in warm atomic vapor  

E-Print Network (OSTI)

Reversible and coherent storage of light in atomic medium is a key-stone of future quantum information applications. In this work, arbitrary two-dimensional images are slowed and stored in warm atomic vapor for up to 30 $\\mu$s, utilizing electromagnetically induced transparency. Both the intensity and the phase patterns of the optical field are maintained. The main limitation on the storage resolution and duration is found to be the diffusion of atoms. A techniqueanalogous to phase-shift lithography is employed to diminish the effect of diffusion on the visibility of the reconstructed image.

M. Shuker; O. Firstenberg; R. Pugatch; A. Ron; N. Davidson

2008-06-17T23:59:59.000Z

140

Recovery of benzene in an organic vapor monitor  

E-Print Network (OSTI)

solid adsorbents available (silica gel, activated alumina, etc. ), activated charcoal is most frequently utilized. Activated charcoal has retentivity for sorbed vapors several times that of silica gel and it displays a selectivity for organic vapors... (diffusion rate) of the vapor molecules to the sur- face of the adsorbent. The adsorption process determine how effective the adsorbent collects and holds the contam- inant on the surface of the activated charcoal. Recovery of the contaminant from...

Krenek, Gregory Joel

2012-06-07T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Mercury Vapor At Haleakala Volcano Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

Mercury Vapor At Haleakala Volcano Area (Thomas, 1986) Mercury Vapor At Haleakala Volcano Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Haleakala Volcano Area (Thomas, 1986) Exploration Activity Details Location Haleakala Volcano Area Exploration Technique Mercury Vapor Activity Date Usefulness not indicated DOE-funding Unknown Notes The field survey program on the northwest rift zone consisted of soil mercury and radon emanometry surveys, groundwater temperature and chemistry studies, Schlumberger resistivity soundings and self-potential profiles. Geophysical and geochemical surveys along this rift (southwest) were limited by difficult field conditions and access limitations. The geophysical program consisted of one Schlumberger sounding, one

142

Mercury Vapor At Vale Hot Springs Area (Varekamp & Buseck, 1983...  

Open Energy Info (EERE)

Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Vale Hot Springs Area (Varekamp & Buseck, 1983) Exploration Activity Details...

143

Mercury Vapor At Breitenbush Hot Springs Area (Varekamp & Buseck...  

Open Energy Info (EERE)

Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Breitenbush Hot Springs Area (Varekamp & Buseck, 1983) Exploration Activity...

144

Mercury Vapor At Mickey Hot Springs Area (Varekamp & Buseck,...  

Open Energy Info (EERE)

Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Mickey Hot Springs Area (Varekamp & Buseck, 1983) Exploration Activity...

145

Mercury Vapor At Desert Peak Area (Varekamp & Buseck, 1983) ...  

Open Energy Info (EERE)

Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Desert Peak Area (Varekamp & Buseck, 1983) Exploration Activity Details...

146

Mercury Vapor At Socorro Mountain Area (Kooten, 1987) | Open...  

Open Energy Info (EERE)

Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Socorro Mountain Area (Kooten, 1987) Exploration Activity Details Location...

147

Mercury Vapor At Lassen Volcanic National Park Area (Varekamp...  

Open Energy Info (EERE)

Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Lassen Volcanic National Park Area (Varekamp & Buseck, 1983) Exploration...

148

Thermal Performance of a Double-Tube Type Lng Vaporizer  

Science Journals Connector (OSTI)

This report concerns the confirmed test results and method of analysis of the thermal performance of a double-tube type LNG vaporizer (DTV). The DTV is a...

Y. Miyata; T. Miura; S. Kasahara; H. Shohtani…

1994-01-01T23:59:59.000Z

149

Optimal Control of Vapor Extraction of Heavy Oil.  

E-Print Network (OSTI)

??Vapor extraction (Vapex) process is an emerging technology for viscous oil recovery that has gained much attention in the oil industry. However, the oil production… (more)

Muhamad, Hameed (Author)

2012-01-01T23:59:59.000Z

150

Geographic Information System At Cove Fort Area - Vapor (Nash...  

Open Energy Info (EERE)

navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Geographic Information System At Cove Fort Area - Vapor (Nash, Et Al., 2002) Exploration Activity Details...

151

Raman Lidar Measurements of Aerosols and Water Vapor During the...  

NLE Websites -- All DOE Office Websites (Extended Search)

modifications reduced but could not eliminate these adverse effects. The Raman lidar water vapor (aerosol extinction) measurements produced by these modified algorithms were,...

152

Thermal Gradient Holes At Cove Fort Area - Vapor (Warpinski,...  

Open Energy Info (EERE)

Warpinski, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Thermal Gradient Holes At Cove Fort Area - Vapor (Warpinski, Et Al.,...

153

Ground Magnetics At Cove Fort Area - Vapor (Warpinski, Et Al...  

Open Energy Info (EERE)

Vapor (Warpinski, Et Al., 2004) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Ground Magnetics Activity Date Usefulness useful DOE-funding...

154

Spray structures and vaporizing characteristics of a GDI fuel spray  

Science Journals Connector (OSTI)

The spray structures and distribution characteristics of liquid and vapor phases in non-evaporating and evaporating Gasoline Direct Injection (GDI) fuel sprays were investigated using Laser Induced...

Dong-Seok Choi; Gyung-Min Choi; Duck-Jool Kim

2002-07-01T23:59:59.000Z

155

Vapor and gas sampling of Single-Shell Tank 241-T-111 using the vapor sampling system  

SciTech Connect

This document presents sampling data resulting from the January 20, 1995, sampling of SST 241-T-111 using the vapor sampling system.

Caprio, G.S.

1995-09-01T23:59:59.000Z

156

Vapor and gas sampling of single-shell tank 241-BY-112 using the vapor sampling system  

SciTech Connect

This document presents sampling data from the November 18, 1994, sampling of SST 241-BY-112 using the vapor sampling system.

Caprio, G.S.

1995-09-20T23:59:59.000Z

157

Informal Report . VAPOR DETECTION OF TRAFFICKING OF CONTRABAND MONEY-  

E-Print Network (OSTI)

I BNL- 62834 Informal Report . VAPOR DETECTION OF TRAFFICKING OF CONTRABAND MONEY-· [D VAPOR DETECTION OF TRAFFICKING OF CONTRABAND MONEY- A DISCUSSION OF TECHNICAL FEASIBILITY Concept MONEY --A DISCUSSION OF TECHNICAL FEASffiILITY Russell N. Dietz, Head Tracer Technology Center

158

RESONANT FARADAY ROTATION IN A HOT LITHIUM VAPOR  

E-Print Network (OSTI)

RESONANT FARADAY ROTATION IN A HOT LITHIUM VAPOR By SCOTT RUSSELL WAITUKAITIS A Thesis Submitted: #12;Abstract I describe a study of Faraday rotation in a hot lithium vapor. I begin by dis- cussing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.3 The Lithium Oven and Solenoid . . . . . . . . . . . . . . . . . 7 3 Theoretical Framework

Cronin, Alex D.

159

FLAMMABILITY CHARACTERISTICS OF COMBUSTIBLE GASES AND VAPORS  

Office of Scientific and Technical Information (OSTI)

Bulletin 627 Bulletin 627 BUREAU o b MINES FLAMMABILITY CHARACTERISTICS OF COMBUSTIBLE GASES AND VAPORS By Michael G. Zabetakis DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency Thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement,

160

New Regenerative Cycle for Vapor Compression Refrigeration  

Office of Scientific and Technical Information (OSTI)

SCIENTIFIC REPORT SCIENTIFIC REPORT Title Page Project Title: New Regenerative Cycle for Vapor Compression Refrigeration DOE Award Number: DE-FG36-04GO14327 Document Title: Final Scientific Report Period Covered by Report: September 30, 2004 to September 30, 2005 Name and Address of Recipient Organization: Magnetic Development, Inc., 68 Winterhill Road, Madison, CT 06443, phone: 203-214-7247, fax: 203-421-7948, e-mail: mjb1000@aol.com Contact Information: Mark J. Bergander, Ph.D., P.E., Principal Investigator, phone: 203-214-7247, fax: 203-421-7948, e-mail: mjb1000@aol.com Project Objective (as stated in the proposal): The main objective of this project is to confirm on a well-instrumented prototype the theoretically derived claims of higher efficiency and coefficient

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Chemical vapor deposition of group IIIB metals  

DOE Patents (OSTI)

Coatings of Group IIIB metals and compounds thereof are formed by chemical vapor deposition, in which a heat decomposable organometallic compound of the formula given in the patent where M is a Group IIIB metal, such as lanthanum or yttrium and R is a lower alkyl or alkenyl radical containing from 2 to about 6 carbon atoms, with a heated substrate which is above the decomposition temperature of the organometallic compound. The pure metal is obtained when the compound of the formula 1 is the sole heat decomposable compound present and deposition is carried out under nonoxidizing conditions. Intermetallic compounds such as lanthanum telluride can be deposited from a lanthanum compound of formula 1 and a heat decomposable tellurium compound under nonoxidizing conditions.

Erbil, A.

1989-11-21T23:59:59.000Z

162

Kinetics of wet sodium vapor complex plasma  

SciTech Connect

In this paper, we have investigated the kinetics of wet (partially condensed) Sodium vapor, which comprises of electrons, ions, neutral atoms, and Sodium droplets (i) in thermal equilibrium and (ii) when irradiated by light. The formulation includes the balance of charge over the droplets, number balance of the plasma constituents, and energy balance of the electrons. In order to evaluate the droplet charge, a phenomenon for de-charging of the droplets, viz., evaporation of positive Sodium ions from the surface has been considered in addition to electron emission and electron/ion accretion. The analysis has been utilized to evaluate the steady state parameters of such complex plasmas (i) in thermal equilibrium and (ii) when irradiated; the results have been graphically illustrated. As a significant outcome irradiated, Sodium droplets are seen to acquire large positive potential, with consequent enhancement in the electron density.

Mishra, S. K., E-mail: nishfeb@rediffmail.com [Institute for Plasma Research (IPR), Gandhinagar 382428 (India); Sodha, M. S. [Centre of Energy Studies, Indian Institute of Technology Delhi (IITD), New Delhi 110016 (India)] [Centre of Energy Studies, Indian Institute of Technology Delhi (IITD), New Delhi 110016 (India)

2014-04-15T23:59:59.000Z

163

Photo-Electric Ionization of Caesium Vapor  

Science Journals Connector (OSTI)

Measurement of photo-electric ionization in gases.—The current from a filament, normally limited by space change, is increased by the presence of positive ions. As shown by Kingdon this effect may be greatly magnified if a small cathode is practically enclosed by the anode so that the ions are imprisoned. This method was used for the detection of photo-electric ionization. Besides possessing extreme sensitivity it is unaffected by photo-electric emission from the electrodes.Photo-electric effect in caesium vapor.—The change in thermionic current with the unresolved radiation from a mercury arc was measured as functions of the applied voltage, filament temperature, and vapor pressure. Then the photo-electric effect as a function of wave-length was studied using a monochromatic illuminator to disperse light from the arc or a Mazda lamp. The ionization per unit flux was found to increase with increasing wave-length to a sharp maximum at the limit 1s=3184A of the principal series, as is required by the Bohr theory. For longer wave-lengths the ionization decreased to about 10 percent at 3400A. Photo-excitation. The simple theory does not admit of ionization by wave-lengths greater than 3184A but the data are in qualitative agreement with the hypothesis that such radiation produces excited atoms which upon collision with other atoms acquire sufficient additional energy to become ionized. Hence, unlike an x-ray limit, the photo-ionization effect for a valence electron is not sharply discontinuous at the true threshold for direct ionization.Photo-ionization photometer and intensitometer. A tube of the type described, with suitable gases for the range of wave-length involved, may be used as a photometer or may be calibrated to measure intensity of radiation directly.

Paul D. Foote and F. L. Mohler

1925-08-01T23:59:59.000Z

164

Gas Separation Using Organic-Vapor-Resistent Membranes In Conjunctin With Organic-Vapor-Selective Membranes  

DOE Patents (OSTI)

A process for treating a gas mixture containing at least an organic compound gas or vapor and a second gas, such as natural gas, refinery off-gas or air. The process uses two sequential membrane separation steps, one using membrane selective for the organic compound over the second gas, the other selective for the second gas over the organic vapor. The second-gas-selective membranes use a selective layer made from a polymer having repeating units of a fluorinated polymer, and demonstrate good resistance to plasticization by the organic components in the gas mixture under treatment, and good recovery after exposure to liquid aromatic hydrocarbons. The membrane steps can be combined in either order.

Baker, Richard W. (Palo Alto, CA); Pinnau, Ingo (Palo Alto, CA); He, Zhenjie (Fremont, CA); Da Costa, Andre R. (Menlo Park, CA); Daniels, Ramin (San Jose, CA); Amo, Karl D. (Mountain View, CA); Wijmans, Johannes G. (Menlo Park, CA)

2003-06-03T23:59:59.000Z

165

Hybrid Vapor Compression Adsorption System: Thermal Storage Using Hybrid Vapor Compression Adsorption System  

SciTech Connect

HEATS Project: UTRC is developing a new climate-control system for EVs that uses a hybrid vapor compression adsorption system with thermal energy storage. The targeted, closed system will use energy during the battery-charging step to recharge the thermal storage, and it will use minimal power to provide cooling or heating to the cabin during a drive cycle. The team will use a unique approach of absorbing a refrigerant on a metal salt, which will create a lightweight, high-energy-density refrigerant. This unique working pair can operate indefinitely as a traditional vapor compression heat pump using electrical energy, if desired. The project will deliver a hot-and-cold battery that provides comfort to the passengers using minimal power, substantially extending the driving range of EVs.

None

2012-01-04T23:59:59.000Z

166

Intermediate frequency band digitized high dynamic range radiometer system for plasma diagnostics and real-time Tokamak control  

SciTech Connect

An intermediate frequency (IF) band digitizing radiometer system in the 100-200 GHz frequency range has been developed for Tokamak diagnostics and control, and other fields of research which require a high flexibility in frequency resolution combined with a large bandwidth and the retrieval of the full wave information of the mm-wave signals under investigation. The system is based on directly digitizing the IF band after down conversion. The enabling technology consists of a fast multi-giga sample analog to digital converter that has recently become available. Field programmable gate arrays (FPGA) are implemented to accomplish versatile real-time data analysis. A prototype system has been developed and tested and its performance has been compared with conventional electron cyclotron emission (ECE) spectrometer systems. On the TEXTOR Tokamak a proof of principle shows that ECE, together with high power injected and scattered radiation, becomes amenable to measurement by this device. In particular, its capability to measure the phase of coherent signals in the spectrum offers important advantages in diagnostics and control. One case developed in detail employs the FPGA in real-time fast Fourier transform (FFT) and additional signal processing. The major benefit of such a FFT-based system is the real-time trade-off that can be made between frequency and time resolution. For ECE diagnostics this corresponds to a flexible spatial resolution in the plasma, with potential application in smart sensing of plasma instabilities such as the neoclassical tearing mode (NTM) and sawtooth instabilities. The flexible resolution would allow for the measurement of the full mode content of plasma instabilities contained within the system bandwidth.

Bongers, W. A.; Beveren, V. van; Westerhof, E.; Goede, A. P. H.; Krijger, B.; Berg, M. A. van den; Graswinckel, M. F.; Schueller, F. C. [FOM-Institute for Plasma Physics Rijnhuizen, Association EURATOM-FOM, Trilateral Euregio Cluster, PO Box 1207, 3430 BE Nieuwegein (Netherlands); Thoen, D. J. [Kavli Institute of Nanoscience, Delft University of Technology, Lorentzweg 1, 2628 CJ Delft (Netherlands); Nuij, P. J. W. M. [Eindhoven University of Technology, Control Systems Technology Group, and Applied Physics Department, PO Box 513, NL-5600 MB Eindhoven (Netherlands); Baar, M. R. de; Donne, A. J. H.; Hennen, B. A. [FOM-Institute for Plasma Physics Rijnhuizen, Association EURATOM-FOM, Trilateral Euregio Cluster, PO Box 1207, 3430 BE Nieuwegein (Netherlands); Eindhoven University of Technology, Control Systems Technology Group, and Applied Physics Department, PO Box 513, NL-5600 MB Eindhoven (Netherlands); Kantor, M. [FOM-Institute for Plasma Physics Rijnhuizen, Association EURATOM-FOM, Trilateral Euregio Cluster, PO Box 1207, 3430 BE Nieuwegein (Netherlands); Forschungszentrum Juelich GMBH, Institute of Energy and Climate research, Plasma Physics, Association EURATOM-FZJ, Trilateral Euregio Cluster, 52425 Juelich (Germany); Ioffe Institute, RAS, Saint-Petersburg, 195256 (Russian Federation)

2011-06-15T23:59:59.000Z

167

E-Print Network 3.0 - atomic vapor laser Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

with the exception of pagination. IEEE TRANSACTIONS ON PLASMA SCIENCE 1 Summary: vapor, atomic physics and vapor ionization, absorption reflection in a heated plasma layer, and...

168

E-Print Network 3.0 - atom vapor cells Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

rotation in the vapor cell due to inten- sity-induced birefringence in the rubidium atomic vapor. While... Super efficient absorption filter for quantum memory using atomic...

169

Preliminary assessment of halogenated alkanes as vapor-phase tracers  

SciTech Connect

New tracers are needed to evaluate the efficiency of injection strategies in vapor-dominated environments. One group of compounds that seems to meet the requirements for vapor-phase tracing are the halogenated alkanes (HCFCs). HCFCs are generally nontoxic, and extrapolation of tabulated thermodynamic data indicate that they will be thermally stable and nonreactive in a geothermal environment. The solubilities and stabilities of these compounds, which form several homologous series, vary according to the substituent ratios of fluorine, chlorine, and hydrogen. Laboratory and field tests that will further define the suitability of HCFCs as vapor-phase tracers are under way.

Adams, Michael C.; Moore, Joseph N.; Hirtz, Paul

1991-01-01T23:59:59.000Z

170

Mercury Vapor At Medicine Lake Area (Kooten, 1987) | Open Energy  

Open Energy Info (EERE)

Kooten, 1987) Kooten, 1987) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Medicine Lake Area (Kooten, 1987) Exploration Activity Details Location Medicine Lake Area Exploration Technique Mercury Vapor Activity Date Usefulness could be useful with more improvements DOE-funding Unknown References Gerald K. Van Kooten (1987) Geothermal Exploration Using Surface Mercury Geochemistry Retrieved from "http://en.openei.org/w/index.php?title=Mercury_Vapor_At_Medicine_Lake_Area_(Kooten,_1987)&oldid=386431" Category: Exploration Activities What links here Related changes Special pages Printable version Permanent link Browse properties 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation:

171

Design of a Shadowband Spectral Radiometer for the Retrieval of Thin Cloud Optical Depth, Liquid Water Path, and the Effective Radius  

SciTech Connect

The design and operation of a Thin-Cloud Rotating Shadowband Radiometer (TCRSR) described here was used to measure the radiative intensity of the solar aureole and enable the simultaneous retrieval of cloud optical depth, drop effective radius, and liquid water path. The instrument consists of photodiode sensors positioned beneath two narrow metal bands that occult the sun by moving alternately from horizon to horizon. Measurements from the narrowband 415-nm channel were used to demonstrate a retrieval of the cloud properties of interest. With the proven operation of the relatively inexpensive TCRSR instrument, its usefulness for retrieving aerosol properties under cloud-free skies and for ship-based observations is discussed.

Bartholomew M. J.; Reynolds, R. M.; Vogelmann, A. M.; Min, Q.; Edwards, R.; Smith, S.

2011-11-01T23:59:59.000Z

172

Catalytic Reactor For Oxidizing Mercury Vapor  

DOE Patents (OSTI)

A catalytic reactor (10) for oxidizing elemental mercury contained in flue gas is provided. The catalyst reactor (10) comprises within a flue gas conduit a perforated corona discharge plate (30a, b) having a plurality of through openings (33) and a plurality of projecting corona discharge electrodes (31); a perforated electrode plate (40a, b, c) having a plurality of through openings (43) axially aligned with the through openings (33) of the perforated corona discharge plate (30a, b) displaced from and opposing the tips of the corona discharge electrodes (31); and a catalyst member (60a, b, c, d) overlaying that face of the perforated electrode plate (40a, b, c) opposing the tips of the corona discharge electrodes (31). A uniformly distributed corona discharge plasma (1000) is intermittently generated between the plurality of corona discharge electrode tips (31) and the catalyst member (60a, b, c, d) when a stream of flue gas is passed through the conduit. During those periods when corona discharge (1000) is not being generated, the catalyst molecules of the catalyst member (60a, b, c, d) adsorb mercury vapor contained in the passing flue gas. During those periods when corona discharge (1000) is being generated, ions and active radicals contained in the generated corona discharge plasma (1000) desorb the mercury from the catalyst molecules of the catalyst member (60a, b, c, d), oxidizing the mercury in virtually simultaneous manner. The desorption process regenerates and activates the catalyst member molecules.

Helfritch, Dennis J. (Baltimore, MD)

1998-07-28T23:59:59.000Z

173

Laser techniques for studying chemical vapor deposition  

SciTech Connect

Chemical vapor deposition (CVD) is widely used to produce thin films for microelectronics, protective coatings and other materials processing applications. Despite the large number of applications, however, little is known about the fundamental chemistry and physics of most CVD processes. CVD recipes have generally been determined empirically, but as process requirements become more stringent, a more basic understanding will be needed to improve reactor design and speed process optimization. In situ measurements of the reacting gas are important steps toward gaining such an understanding, both from the standpoint of characterizing the reactor and testing models of a CVD process. Our work, a coordinated program of experimental and theoretical research in the fundamental mechanisms of CVD, illustrates the application of laser techniques to the understanding of a CVD system. We have used a number of laser-based techniques to probe CVD systems and have compared our measurements with predictions from computer models, primarily for the silane CVD system. The silane CVD model solves the two-dimensional, steady-state boundary layer equations of fluid flow coupled to 26 elementary chemical reactions describing the thermal decomposition of silane and the subsequent reactions of intermediate species that result in the deposition of a silicon film.

Ho, P.; Breiland, W.G.; Coltrin, M.E.

1990-01-01T23:59:59.000Z

174

MWRRET (Microwave Radiometer Retrievals)  

NLE Websites -- All DOE Office Websites (Extended Search)

Plus Plus Plus Andy Vogelmann, Dave Turner Andy Vogelmann, Dave Turner & Jennifer Comstock & Jennifer Comstock Min Min Susanne Crewell Susanne Crewell Ulrich L Ulrich L ö ö rnard rnard Jim Liljegren Jim Liljegren John Ogre John Ogre . Y. Matrosov . Y. Matrosov Sally McFarlane Sally McFarlane Warren Wiscombe, Christine Chiu, Sasha Marshak, Maria Warren Wiscombe, Christine Chiu, Sasha Marshak, Maria Cadeddu, Qilong Min, Susanne Crewell, Ulrich L Cadeddu, Qilong Min, Susanne Crewell, Ulrich L ö ö hnert, Mandy hnert, Mandy M. Khaiyer, Greg McFarquhar , Chuck Long, Bill O M. Khaiyer, Greg McFarquhar , Chuck Long, Bill O ' ' Hirok, Bin Hirok, Bin Lin, Connor Flynn, Eli Mlawer, Graham Feingold, Jim Barnard, Lin, Connor Flynn, Eli Mlawer, Graham Feingold, Jim Barnard,

175

Radiometer Calibration Trends  

NLE Websites -- All DOE Office Websites (Extended Search)

Wilcox, T. L. Stoffel, and D. R. Myers National Renewable Energy Laboratory Golden, Colorado Abstract Calibrations of Atmospheric Radiation Measurement (ARM) broadband...

176

Inexpensive photovoltaic solar radiometer  

Science Journals Connector (OSTI)

Using a solar cell as a sensor a low?cost instrument can be constructed which measures both the instantaneous and integrated value of solar flux. The process of constructing and calibrating the instrument constitutes an excellent undergraduate experimental project affording the student an opportunity to examine a variety of aspects associated with solar energy measurements.

Fritz Kissner

1981-01-01T23:59:59.000Z

177

Overview of the ARM/FIRE Water Vapor Experiment (AFWEX)  

NLE Websites -- All DOE Office Websites (Extended Search)

Overview of the ARM/FIRE Water Vapor Overview of the ARM/FIRE Water Vapor Experiment (AFWEX) D. C. Tobin, H. E. Revercomb, and D. D. Turner University of Wisconsin-Madison Madison, Wisconsin Introduction An overview of the ARM/FIRE Water Vapor Experiment (AFWEX) is given. This field experiment was conducted during November-December 2000 near the central ground-based Atmospheric Radiation Measurement (ARM) site in north central Oklahoma, and was sponsored jointly by the ARM, the National Aeronautics and Space Administration (NASA) First ISCCP Regional Experiment (FIRE), and the National Polar-orbiting Operational Environmental Satellite System (NPOESS) programs. Its primary goal was to collect accurate measurements of upper-level (~8 to 12 km) water vapor near the ground-based ARM site. These data are being used to determine the accuracy of measurements that are

178

Initiated chemical vapor deposition of functional polyacrylic thin films  

E-Print Network (OSTI)

Initiated chemical vapor deposition (iCVD) was explored as a novel method for synthesis of functional polyacrylic thin films. The process introduces a peroxide initiator, which can be decomposed at low temperatures (<200?C) ...

Mao, Yu, 1975-

2005-01-01T23:59:59.000Z

179

Low Level Heat Recovery Through Heat Pumps and Vapor Recompression  

E-Print Network (OSTI)

The intent of this paper is to examine the methods and economics of recovering low level heat through heat pumps and vapor recompression. Actual commercially available equipment is considered to determine the near-term and future economic viability...

Gilbert, J.

1980-01-01T23:59:59.000Z

180

Applications of Mechanical Vapor Recompression to Evaporation and Crystallization  

E-Print Network (OSTI)

there is no boiler plant available or when electrical power is priced competitively in comparison to steam. Vapor recompression is accomplished using centrifugal, axial-flow, or positive displacement compressors and these compressors can be powered by electricity...

Outland, J. S.

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Enabling integration of vapor-deposited polymer thin films  

E-Print Network (OSTI)

Initiated Chemical Vapor Deposition (iCVD) is a versatile, one-step process for synthesizing conformal and functional polymer thin films on a variety of substrates. This thesis emphasizes the development of tools to further ...

Petruczok, Christy D. (Christy Danielle)

2014-01-01T23:59:59.000Z

182

Hyperfine Studies of Lithium Vapor using Saturated Absorption Spectroscopy  

E-Print Network (OSTI)

the frequency of a laser with respect to an atomic spectral feature.[20] As such, saturated absorptionHyperfine Studies of Lithium Vapor using Saturated Absorption Spectroscopy? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.3 Broadening Mechanisms . . . . . . . . . . . . . . . . . . . . . 15 3.4 Saturated Absorption

Cronin, Alex D.

183

All graphene electromechanical switch fabricated by chemical vapor deposition  

E-Print Network (OSTI)

We demonstrate an electromechanical switch comprising two polycrystalline graphene films; each deposited using ambient pressure chemical vapor deposition. The top film is pulled into electrical contact with the bottom film ...

Milaninia, Kaveh M.

184

Systems and methods for generation of hydrogen peroxide vapor  

DOE Patents (OSTI)

A system according to one embodiment includes a moisture trap for drying air; at least one of a first container and a second container; and a mechanism for at least one of: bubbling dried air from the moisture trap through a hydrogen peroxide solution in the first container for producing a hydrogen peroxide vapor, and passing dried air from the moisture trap into a headspace above a hydrogen peroxide solution in the second container for producing a hydrogen peroxide vapor. A method according one embodiment includes at least one of bubbling dried air through a hydrogen peroxide solution in a container for producing a first hydrogen peroxide vapor, and passing dried air from the moisture trap into a headspace above the hydrogen peroxide solution in a container for producing a second hydrogen peroxide vapor. Additional systems and methods are also presented.

Love, Adam H; Eckels, Joel Del; Vu, Alexander K; Alcaraz, Armando; Reynolds, John G

2014-12-02T23:59:59.000Z

185

Optical Precursors in Rubidium Vapor and Their Relation to Superradiance  

E-Print Network (OSTI)

Optical precursor is the sharp optical pulse front that does not show delay in absorptive media. In this thesis, optical precursor behavior in rubidium (Rb) vapor was investigated in the picoseconds regime. An amplified femtosecond laser was shaped...

Yang, Wenlong

2012-10-19T23:59:59.000Z

186

Photocoupling of Methane in Water Vapor to Saturated Hydrocarbons  

Science Journals Connector (OSTI)

Methane can be converted into alkanes (from C2 to C6) continuously by ultraviolet (185 nm) irradiation in the presence of water vapor. The products from this reaction are alkanes, which is different from the comp...

JunePyo Oh; Taketoshi Matsumoto; Junji Nakamura

2008-08-01T23:59:59.000Z

187

Mercury Vapor At Kawaihae Area (Thomas, 1986) | Open Energy Information  

Open Energy Info (EERE)

Mercury Vapor At Kawaihae Area (Thomas, 1986) Mercury Vapor At Kawaihae Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Kawaihae Area (Thomas, 1986) Exploration Activity Details Location Kawaihae Area Exploration Technique Mercury Vapor Activity Date Usefulness not useful DOE-funding Unknown Notes The soil geochemistry yielded quite complex patterns of mercury concentrations and radonemanation rates within the survey area (Cox and Cuff, 1981c). Mercury concentrations (Fig. 38) showed a general minimum along the Kawaihae-Waimea roads and a broad trend of increasing mercury concentrations toward both the north and south. There is no correlation apparent between the mercury patterns and either the resistivity sounding data or the surface geology in the area. The radon emanometry data (Fig.

188

Mercury Vapor At Lualualei Valley Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

Mercury Vapor At Lualualei Valley Area (Thomas, 1986) Mercury Vapor At Lualualei Valley Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Lualualei Valley Area (Thomas, 1986) Exploration Activity Details Location Lualualei Valley Area Exploration Technique Mercury Vapor Activity Date Usefulness useful DOE-funding Unknown Notes Soil mercury and radon emanation surveys were performed over much of the accessible surface of Lualualei Valley (Cox and Thomas, 1979). The results of these surveys (Figs 7 and 8) delineated several areas in which soil mercury concentrations or radon emanation rates were substantially above normal background values. Some of these areas were apparently coincident with the mapped fracture systems associated with the caldera boundaries.

189

Advanced Chemical Heat Pumps Using Liquid-Vapor Reactions  

E-Print Network (OSTI)

ically feasible systems have significant potential advantage over conventional tech nology. An electric drive reactive heat pump can use smaller heat exchangers and compressor than a vapor-compression machine, and have more flexible operating... are discussed, and performance is bounded. A discussion on liquid-vapor equilibria is included as introduction to the systems I- considered. The electric drive heat pump and TA are promising systems; the TA has potential for higher COP than absorption...

Kirol, L.

190

D/sup -/ production by charge transfer in metal vapors  

SciTech Connect

Fast D/sup -/ ions can be produced from D/sup +/ by multiple charge-transfer collisions in a metal-vapor target. Experimental cross sections and thick-target D/sup -/ yields are presented and discussed. The high D/sup -/ yield experimentally observed from charge transfer in cesium vapor is consistent with recent low-energy cross-section calculations and measurements.

Schlachter, A.S.

1980-10-01T23:59:59.000Z

191

Injection locked oscillator system for pulsed metal vapor lasers  

DOE Patents (OSTI)

An injection locked oscillator system for pulsed metal vapor lasers is disclosed. The invention includes the combination of a seeding oscillator with an injection locked oscillator (ILO) for improving the quality, particularly the intensity, of an output laser beam pulse. The present invention includes means for matching the first seeder laser pulses from the seeding oscillator to second laser pulses of a metal vapor laser to improve the quality, and particularly the intensity, of the output laser beam pulse.

Warner, Bruce E. (Livermore, CA); Ault, Earl R. (Dublin, CA)

1988-01-01T23:59:59.000Z

192

Tank 241-S-102 headspace gas and vapor characterization results for samples collected in March 1995  

SciTech Connect

Significant changes have been made to all of the original vapor characterization reports. This report documents specific headspace gas and vapor characterization results for all vapor sampling events to date. In addition, changes have been made to the original vapor reports to qualify the data based on quality assurance issues associated with the performing laboratories

Huckaby, J.L. [Pacific Northwest Lab., Richland, WA (United States); Bratzel, D.R. [Westinghouse Hanford Co., Richland, WA (United States)

1995-09-26T23:59:59.000Z

193

investigating the source, transport, and isotope fractionation of water vapor in the atmospheric boundary layer  

E-Print Network (OSTI)

investigating the source, transport, and isotope fractionation of water vapor in the atmospheric cospectral similarity for temperature and water vapor isotope fluxes. mixing ratio generator Routine field use in water vapor isotope research. The unit generates a stable water vapor mixing ratio by measuring

Minnesota, University of

194

Calculating the vapor pressure of water from the second law of thermodynamics  

Science Journals Connector (OSTI)

Calculating the vapor pressure of water from the second law of thermodynamics ... Thermodynamics ...

M. H. Everdell

1969-01-01T23:59:59.000Z

195

The growth of vapor bubble and relaxation between two-phase bubble flow  

Science Journals Connector (OSTI)

This paper presents the behavior of the bubble growth and relaxation between vapor and superheated...

S. Mohammadein; Rama Subba Reddy Gorla

2003-01-01T23:59:59.000Z

196

Tank Vapor Characterization Project: Annual status report for FY 1996  

SciTech Connect

In Fiscal Year 1996, staff at the Vapor Analytical Laboratory at Pacific Northwest National Laboratory performed work in support of characterizing the vapor composition of the headspaces of radioactive waste tanks at the Hanford Site. Work performed included support for technical issues and sampling methodologies, upgrades for analytical equipment, analytical method development, preparation of unexposed samples, analyses of tank headspaces samples, preparation of data reports, and operation of the tank vapor database. Progress made in FY 1996 included completion and issuance of 50 analytical data reports. A sampling system comparison study was initiated and completed during the fiscal year. The comparison study involved the vapor sampling system (VSS), a truck-based system, and the in situ vapor sampling system (ISVS), a cart-based system. Samples collected during the study were characterized for inorganic, permanent gases, total non-methane organic compounds and organic speciation by SUMMA{trademark} and TST methods. The study showed comparable sampling results between the systems resulting in the program switching from the VSS to the less expensive ISVS methodology in late May 1996. A temporal study was initiated in January 1996 in order to understand the influences seasonal temperatures changes have on the vapors in the headspace of Hanford waste tanks. A holding time study was initiated in the fourth quarter of FY 1996. Samples were collected from tank S-102 and rushed to the laboratory for time zero analysis. Additional samples will be analyzed at 1, 2, 4, 8, 16, and 32 weeks.

Silvers, K.L.; Fruchter, J.S.; Huckaby, J.L.; Almeida, T.L.; Evans, J.C. Jr.; Pool, K.H.; Simonen, C.A.; Thornton, B.M.

1997-01-01T23:59:59.000Z

197

Mercury Source Zone Identification using Soil Vapor Sampling and Analysis  

SciTech Connect

Development and demonstration of reliable measurement techniqes that can detect and help quantify the nature and extent of elemental mercury (Hg(0)) in the subsurface are needed to reduce certainties in the decision making process and increase the effectiveness of remedial actions. We conducted field tests at the Y-12 National Security Complex (NSC) in Oak Ridge, TN, to determine if sampling and analysis of Hg(0) vapors in the shallow subsurface (<0.3 m depth) can be used to as an indicator of the location and extent of Hg(0) releases in the subsurface. We constructed a rigid PVC pushprobe assembly, which was driven into the ground. Soil gas samples were collected through a sealed inner tube of the assembly and analyzed immediately in the field with a Lumex and/or Jerome Hg(0) analyzer. Time-series sampling showed that Hg vapor concentrations were fairly stable over time suggesting that the vapor phase Hg(0) was not being depleted and that sampling results were not dependent on the soil gas purge volume. Hg(0) vapor data collected at over 200 pushprobe locations at 3 different release sites correlated well to areas of known Hg(0) contamination. Vertical profiling of Hg(0) vapor concentrations conducted at 2 locations provided information on the vertical distribution of Hg(0) contamination in the subsurface. We concluded from our studies that soil gas sampling and analysis can be conducted rapidly and inexpensively at a large scale to help identify areas contaminated with Hg(0).

Watson, David B [ORNL] [ORNL; Miller, Carrie L [ORNL] [ORNL; Lester, Brian P [ORNL] [ORNL; Lowe, Kenneth Alan [ORNL] [ORNL; Southworth, George R [ORNL] [ORNL; Bogle, Mary Anna [ORNL] [ORNL; Liang, Liyuan [ORNL] [ORNL; Pierce, Eric M [ORNL] [ORNL

2014-01-01T23:59:59.000Z

198

Vapor etching of nuclear tracks in dielectric materials  

DOE Patents (OSTI)

A process involving vapor etching of nuclear tracks in dielectric materials for creating high aspect ratio (i.e., length much greater than diameter), isolated cylindrical holes in dielectric materials that have been exposed to high-energy atomic particles. The process includes cleaning the surface of the tracked material and exposing the cleaned surface to a vapor of a suitable etchant. Independent control of the temperatures of the vapor and the tracked materials provide the means to vary separately the etch rates for the latent track region and the non-tracked material. As a rule, the tracked regions etch at a greater rate than the non-tracked regions. In addition, the vapor-etched holes can be enlarged and smoothed by subsequent dipping in a liquid etchant. The 20-1000 nm diameter holes resulting from the vapor etching process can be useful as molds for electroplating nanometer-sized filaments, etching gate cavities for deposition of nano-cones, developing high-aspect ratio holes in trackable resists, and as filters for a variety of molecular-sized particles in virtually any liquid or gas by selecting the dielectric material that is compatible with the liquid or gas of interest.

Musket, Ronald G. (Danville, CA); Porter, John D. (Berkeley, CA); Yoshiyama, James M. (Fremont, CA); Contolini, Robert J. (Lake Oswego, OR)

2000-01-01T23:59:59.000Z

199

Validation of TES Temperature and Water Vapor Retrievals with ARM  

NLE Websites -- All DOE Office Websites (Extended Search)

Validation of TES Temperature and Water Vapor Retrievals with ARM Validation of TES Temperature and Water Vapor Retrievals with ARM Observations Cady-Pereira, Karen Atmospheric and Environmental Research, Inc. Shephard, Mark Atmospheric and Environmental Research, Inc. Clough, Shepard Atmospheric and Environmental Research Mlawer, Eli Atmospheric & Environmental Research, Inc. Turner, David University of Wisconsin-Madison Category: Atmospheric State and Surface The primary objective of the TES (Tropospheric Emission Spectrometer) instrument on the Aura spacecraft is the retrieval of trace gases, especially water vapor and ozone. The TES retrievals extremely useful for global monitoring of the atmospheric state, but they must be validated. The ARM sites are well instrumented and provide continuous measurements, which

200

VAPORIZATION OF TUNGSTEN-METAL IN STEAM AT HIGH TEMPERATURES.  

SciTech Connect

The vaporization of tungsten from the APT spallation target dominates the radiological source term for unmitigated target overheating accidents. Chemical reactions of tungsten with steam which persist to tungsten temperatures as low as 800 C result in the formation of a hydrated tungsten-oxide which has a high vapor pressure and is readily convected in a flowing atmosphere. This low-temperature vaporization reaction essentially removes the oxide film that forms on the tungsten-metal surface as soon as it forms, leaving behind a fresh metallic surface for continued oxidation and vaporization. Experiments were conducted to measure the oxidative vaporization rates of tungsten in steam as part of the effort to quantify the MT radiological source term for severe target accidents. Tests were conducted with tungsten rods (1/8 inch diameter, six inches long) heated to temperatures from approximately 700 C to 1350 C in flowing steam which was superheated to 140 C. A total of 19 experiments was conducted. Fifteen tests were conducted by RF induction heating of single tungsten rods held vertical in a quartz glass retort. Four tests were conducted in a vertically-mounted tube furnace for the low temperature range of the test series. The aerosol which was generated and transported downstream from the tungsten rods was collected by passing the discharged steam through a condenser. This procedure insured total collection of the steam along with the aerosol from the vaporization of the rods. The results of these experiments revealed a threshold temperature for tungsten vaporization in steam. For the two tests at the lowest temperatures which were tested, approximately 700 C, the tungsten rods were observed to oxidize without vaporization. The remainder of the tests was conducted over the temperature range of 800 C to 1350 C. In these tests, the rods were found to have lost weight due to vaporization of the tungsten and the missing weight was collected in the downstream condensate system. The aerosol formed a fine white smoke of tungsten-oxide which was visible to the eye as it condensed in the laminar boundary layer of steam which flowed along the surface of the rod. The aerosol continued to flow as a smoke tube downstream of the rod, flowing coaxially along the centerline axis of the quartz glass tube and depositing by impaction along the outside of a bend and at sudden area contractions in the piping. The vaporization rate data from the 17 experiments which exceeded the vaporization threshold temperature are shown in Figure 5 in the form of vaporization rates (g/cm{sup 2} s) vs. inverse temperature (K{sup {minus}1}). Two correlations to the present data are presented and compared to a published correlation by Kilpatrick and Lott. The differences are discussed.

GREENE,G.A.; FINFROCK,C.C.

2000-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

The BOOMERANG North America Instrument: A Balloon-borne Bolometric Radiometer Optimized for Measurements of Cosmic Background Radiation Anisotropies from 03 to 4°  

Science Journals Connector (OSTI)

We describe the BOOMERANG North America instrument, a balloon-borne bolometric radiometer designed to map the cosmic microwave background (CMB) radiation with 03 resolution over a significant portion of the sky. This receiver employs new technologies in bolometers, readout electronics, millimeter-wave optics and filters, cryogenics, scan, and attitude reconstruction. All these subsystems are described in detail in this paper. The system has been fully calibrated in flight using a variety of techniques, which are described and compared. Using this system, we have obtained a measurement of the first peak in the CMB angular power spectrum in a single, few hour long balloon flight. The instrument described here was a prototype of the BOOMERANG Long Duration Balloon experiment.

F. Piacentini; P. A. R. Ade; R. S. Bhatia; J. J. Bock; A. Boscaleri; P. Cardoni; B. P. Crill; P. de Bernardis; H. Del Castillo; G. De Troia; P. Farese; M. Giacometti; E. F. Hivon; V. V. Hristov; A. Iacoangeli; A. E. Lange; S. Masi; P. D. Mauskopf; L. Miglio; C. B. Netterfield; P. Palangio; E. Pascale; A. Raccanelli; S. Rao; G. Romeo; J. Ruhl; F. Scaramuzzi

2002-01-01T23:59:59.000Z

202

Phase effects for electrons in liquid water and water vapor  

SciTech Connect

The objective of these studies is to compare transport, energy loss, and other phenomena for electrons in water in the liquid and vapor phases. Understanding the differences and similarities is an interesting physics problem in its own right. It is also important for applying the relatively large body of experimental data available for the vapor to the liquid, which is of greater relevance in radiobiology. This paper presents a summary of results from a series of collaborative studies carried out by the authors at Oak Ridge National Laboratory (ORNL) and the Gesellschaft fuer Strahlen- und Umweltforschung (GSF). 14 figs.

Turner, J.E.; Paretzke, H.G.; Wright, H.A.; Hamm, R.N.; Ritchie, R.H.

1988-01-01T23:59:59.000Z

203

Growth of manganese filled carbon nanofibers in the vapor phase  

Science Journals Connector (OSTI)

We report the vapor phase growth of partially filled graphitic fibers, 20-30 nm in diameter and up to a micron in length, during a manganese catalyzed carbon electric arc discharge. The fiber morphology resembles that of catalytic chemical vapor deposited carbon filaments but the inside hollow contains intermittent precipitates and continuous filling of Mn that at times occupy >50% of fiber lengths. Transmission electron microscopy and electron energy loss line spectra show that the fillings form as solid cores and may correspond to pure metal.

P. M. Ajayan; C. Colliex; J. M. Lambert; P. Bernier; L. Barbedette; M. Tence; O. Stephan

1994-03-14T23:59:59.000Z

204

The development of a passive dosimeter for airborne aniline vapors  

E-Print Network (OSTI)

passive sampl1ng dosimeter was designed to measure concen- trat1ons of aniline vapor in air. Diffus1on tubes of 1. 5, 3. 0 and 4. 5 cm lengths were tested under controlled conditions of relative humid1ty, air temperature and vapor concentrations. A... of Measured vs Calculated Concentrations APPENDIX D-Student-t Test on Slopes of Measured vs Calculated Data . APPENDIX E-Statistical Analysis of Four Hour Time- Weighted Average Study on 3. 0 cm Dosimeter VITA ~pa e 42 45 48 59 62 63 65 70 73...

Campbell, James Evan

1977-01-01T23:59:59.000Z

205

Solid–Liquid–Vapor Equilibrium Models for Cryogenic Biogas Upgrading  

Science Journals Connector (OSTI)

In cryogenic upgrading processes involving dry ice formation, accurate predictions of solid–liquid, solid–vapor, and solid–liquid–vapor equilibria are fundamental for a correct design of the heat exchanger surface in order to achieve the desired biomethane purity. ... Moreover, the liquefied biogas production process, particularly interesting for cryogenic upgrading processes due to the low temperature of the obtained biomethane, requires an accurate knowledge of carbon dioxide solubility in liquid methane to avoid solid deposition. ... For some applications demanding a high energy content gas, namely vehicle fuels and injection in the natural gas grid, the biogas has to be upgraded into biomethane. ...

Mauro Riva; Marco Campestrini; Joseph Toubassy; Denis Clodic; Paolo Stringari

2014-10-13T23:59:59.000Z

206

UNCORRECTEDPROOF 2 Vaporization, fusion and sublimation enthalpies of the  

E-Print Network (OSTI)

UNCORRECTEDPROOF 2 Vaporization, fusion and sublimation enthalpies of the 3 dicarboxylic acids from of Chemistry and Biochemistry, University of Missouri-St. Louis, 8001 Natural Bridge, St. Louis, MO 63121, USA observed previously in the sublimation enthalpies of these compounds. The results are dis- 16 cussed

Chickos, James S.

207

Vapor-side corrosion in thermal desalination plants  

SciTech Connect

This article reports the results of vapor-size corrosion monitoring studies carried out in multistage flash (MSF) desal unit No. 100 of Al-Khafji power and Desalination Plant in Saudi Arabia. Corrosion behavior of 70/30 Cu-Ni alloy, carbon steel (CS), and type 316L stainless steel (SS) was studied in vents and in the vapor size of distillers for 2,000, 4,000, and 9,000 h. Analyses of the experimental data indicated that in addition to O{sub 2}, S-containing compounds evolved during flashing of seawater reacted more with Cu-Ni alloy than with CS and type 316L SS. Explanations for comparatively higher corrosion of alloys exposed to the vapors of the first three (1 to 3) and middle (11 to 13) stages of the MSF plant are given with experimental results. Type 316L SS was found to be the alloy most resistant to vapor-side corrosion in all stages of distillers.

Asrar, N.; Malik, A.U.; Ahmed, S. [Saline Water Conversion Corp. (Saudi Arabia); Al-Khalidi, M.; Al-Moaili, K. [Al-Khafji Desalination Plant (Saudi Arabia)

1999-04-01T23:59:59.000Z

208

Fatigue Resistance of Asphalt Mixtures Affected by Water Vapor Movement  

E-Print Network (OSTI)

This dissertation has two key objectives: the first objective is to develop a method of predicting and quantifying the amount of water that can enter into a pavement system by vapor transport; the second objective is to identify to which extent...

Tong, Yunwei

2013-11-08T23:59:59.000Z

209

The chemical vapor deposition of zirconium carbide onto ceramic substrates  

SciTech Connect

Zirconium carbide is an attractive ceramic material due to its unique properties such as high melting point, good thermal conductivity, and chemical resistance. The controlled preparation of zirconium carbide films of superstoichiometric, stoichiometric, and substoichiometric compositions has been achieved utilizing zirconium tetrachloride and methane precursor gases in an atmospheric pressure high temperature chemical vapor deposition system.

Glass, John A, Jr.; Palmisiano, Nick, Jr.; Welsh, R. Edward

1999-07-01T23:59:59.000Z

210

A transient model for a cesium vapor thermionic converter. [Cs  

SciTech Connect

This paper presents an analytical model for simulating the transient and steady-state operation of cesium vapor thermionic converters. A parametric analysis is performed to assess the transient response of the converter to changes in fission power and width of interelectrode gap. The model optimizes the converter performance for maximum electric power to the load.(AIP)

El-Genk, M.S.; Murray, C.S.; Chaudhuri, S. (Institute for Space Nuclear Power Studies, Department of Chemical and Nuclear Engineering, The University of New Mexico, Albuquerque, New Mexico (USA))

1991-01-10T23:59:59.000Z

211

Experimental Study of Water Vapor Adsorption on Geothermal  

E-Print Network (OSTI)

Geothermal Program under Department of Energy Grant No. DE-FG07-90IDI2934,and by the Department of PetroleumSGP-TR-148 Experimental Study of Water Vapor Adsorption on Geothermal Reservoir Rocks Shubo Shang Engineering, Stanford University Stanford Geothermal Program Interdisciplinary Research in Engineering

Stanford University

212

CVD CNT CNT (Vapor-grown carbon fiber, VGCF)  

E-Print Network (OSTI)

CNT CNT CVD CNT CNT (Vapor-grown carbon fiber, VGCF) 10001300 CNT CVD Smalley CO 24 CCVD 1 #12; 27 mm 3% 200 sccm 800 10 10 Torr 300 sccm Ethanol tank Hot bath boat Ar/H2 Ar or Ethanol tank Hot bath Ethanol tank Hot bath Pressure gauge Maindraintube Subdraintube

Maruyama, Shigeo

213

Method for removing metal vapor from gas streams  

DOE Patents (OSTI)

A process for cleaning an inert gas contaminated with a metallic vapor, such as cadmium, involves withdrawing gas containing the metallic contaminant from a gas atmosphere of high purity argon; passing the gas containing the metallic contaminant to a mass transfer unit having a plurality of hot gas channels separated by a plurality of coolant gas channels; cooling the contaminated gas as it flows upward through the mass transfer unit to cause contaminated gas vapor to condense on the gas channel walls; regenerating the gas channels of the mass transfer unit; and, returning the cleaned gas to the gas atmosphere of high purity argon. The condensing of the contaminant-containing vapor occurs while suppressing contaminant particulate formation, and is promoted by providing a sufficient amount of surface area in the mass transfer unit to cause the vapor to condense and relieve supersaturation buildup such that contaminant particulates are not formed. Condensation of the contaminant is prevented on supply and return lines in which the contaminant containing gas is withdrawn and returned from and to the electrorefiner and mass transfer unit by heating and insulating the supply and return lines.

Ahluwalia, R. K. (6440 Hillcrest Dr., Burr Ridge, IL 60521); Im, K. H. (925 Lehigh Cir., Naperville, IL 60565)

1996-01-01T23:59:59.000Z

214

Sorption and Diffusion of Organic Vapors in Two Fluoroelastomers  

E-Print Network (OSTI)

Sorption and Diffusion of Organic Vapors in Two Fluoroelastomers PING WANG,* NATHANIEL S. SCHNEIDER of II in polar liquids: over 100% (wt/wt) in two ketones and a phosphate ester. Sorption isotherms deter determined from sorption kinetics, corrected for nonisothermal effects, and converted to solvent self

Wang, Ping

215

High-resolution terahertz atmospheric water vapor continuum measurements  

E-Print Network (OSTI)

High-resolution terahertz atmospheric water vapor continuum measurements David M. Slocum,* Thomas M such as pollution monitoring and the detection of energetic chemicals using remote sensing over long path lengths through the atmosphere. Although there has been much attention to atmospheric effects over narrow

Massachusetts at Lowell, University of

216

Method and apparatus to measure vapor pressure in a flow system  

DOE Patents (OSTI)

The present invention is directed to a method for determining, by a condensation method, the vapor pressure of a material with a known vapor pressure versus temperature characteristic, in a flow system particularly in a mercury isotope enrichment process.

Grossman, Mark W. (Belmont, MA); Biblarz, Oscar (Swampscott, MA)

1991-01-01T23:59:59.000Z

217

Tropical Water Vapor and Cloud Feedbacks in Climate Models: A Further Assessment Using Coupled Simulations  

Science Journals Connector (OSTI)

By comparing the response of clouds and water vapor to ENSO forcing in nature with that in Atmospheric Model Intercomparison Project (AMIP) simulations by some leading climate models, an earlier evaluation of tropical cloud and water vapor ...

De-Zheng Sun; Yongqiang Yu; Tao Zhang

2009-03-01T23:59:59.000Z

218

Metalorganic chemical vapor deposition of carbon-free ZnO using...  

NLE Websites -- All DOE Office Websites (Extended Search)

Metalorganic chemical vapor deposition of carbon-free ZnO using the bis(2,2,6,6-tetramethyl-3,5-heptanedionato)zinc precursor. Metalorganic chemical vapor deposition of carbon-free...

219

Economic and Technical Tradeoffs Between Open and Closed Cycle Vapor Compression Evaporators  

E-Print Network (OSTI)

and solute. Evaporation tends to be a very energy intensive process. Approximately 1000 BTUs of energy are required to vaporize one pound of water. Many techniques have been developed to reuse energy Within an evaporation system so as to vaporize... Recompression A schematic of an open cycle vapor recompression evaporator is shown in Figure 2. This method uses the vapor in an open cycle for both heating and cooling. Rather than being condensed after the last effect, steam is compressed to a slightly...

Timm, M. L.

220

Quantitative Analysis of Ternary Vapor Mixtures Using a Microcantilever-Based Electronic Nose  

SciTech Connect

The authors report the identification and quantification of the components of a ternary vapor mixture using a microcantilever-based electronic nose. An artificial neural network was used for pattern recognition. Dimethyl methyl phosphonate vapor in ppb concentrations and water and ethanol vapors in ppm concentrations were quantitatively identified either individually or in binary and ternary mixtures at varying concentrations.

Pinnaduwage, Lal A [ORNL; Zhao, Weichang [ORNL; Gehl, Anthony C [ORNL; Allman, Steve L [ORNL

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Sample Vapor Introduction Techniques for Use with Cryofocusing GC Inlet Systems  

Science Journals Connector (OSTI)

......the vapor generator was operated at atmospheric pressure for...condensed water. Other studies...Because the water vapor was...tail of the water peak. Thus...obtained from an atmospheric pressure source...the vapor generator over a 1......

Christine L. Rankin; Richard D. Sacks

1994-01-01T23:59:59.000Z

222

The high-resolution G-banded karyotype of Sus scrofa domestica L  

E-Print Network (OSTI)

and 101 intermediate bands and subbands, according to their relative positions and staining intensities

Boyer, Edmond

223

G? band in double- and triple-walled carbon nanotubes: A Raman study  

E-Print Network (OSTI)

Double- and triple-walled carbon nanotubes are studied in detail by laser energy-dependent Raman spectroscopy in order to get a deeper understanding about the second-order G[superscript '] band Raman process, general ...

Hirschmann, Thomas Ch.

224

Method for the generation of variable density metal vapors which bypasses the liquidus phase  

DOE Patents (OSTI)

The present invention provides a method for producing a metal vapor that includes the steps of combining a metal and graphite in a vessel to form a mixture; heating the mixture to a first temperature in an argon gas atmosphere to form a metal carbide; maintaining the first temperature for a period of time; heating the metal carbide to a second temperature to form a metal vapor; withdrawing the metal vapor and the argon gas from the vessel; and separating the metal vapor from the argon gas. Metal vapors made using this method can be used to produce uniform powders of the metal oxide that have narrow size distribution and high purity.

Kunnmann, Walter (Stony Brook, NY); Larese, John Z. (Rocky Point, NY)

2001-01-01T23:59:59.000Z

225

Mercury Vapor At Mokapu Penninsula Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

Mokapu Penninsula Area (Thomas, 1986) Mokapu Penninsula Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Mokapu Penninsula Area (Thomas, 1986) Exploration Activity Details Location Mokapu Penninsula Area Exploration Technique Mercury Vapor Activity Date Usefulness not useful DOE-funding Unknown Notes The high degree of cultural activity (e.g. residential areas, streets, jet runways, etc.) on Mokapu both limited the extent of the soil geochemical surveys performed and rendered their interpretation much more difficult. Soil mercury concentrations and radon emanometry data on the peninsula showed a few localized high values (Figs 13, 14), but no consistent correlation between the anomalous zones and geologic features could be

226

Detonation wave driven by condensation of supersaturated carbon vapor  

Science Journals Connector (OSTI)

An experimental observation of a detonation wave driven by the energy of condensation of supersaturated carbon vapor is reported. The carbon vapor was formed by the thermal decay of unstable carbon suboxide C3O2 behind shock waves in mixtures containing 10–30% C3O2 in Ar. In the mixture 10% C3O2+Ar the insufficient heat release resulted in a regime of overdriven detonation. In the mixture 20% C3O2+Ar measured values of the pressure and wave velocity coincident with calculated Chapman-Jouguet parameters were attained. In the richest mixture 30% C3O2+Ar an excess heat release caused the slowing down of the condensation rate and the regime of underdriven detonation was observed.

A. Emelianov; A. Eremin; V. Fortov; H. Jander; A. Makeich; H. Gg. Wagner

2009-03-10T23:59:59.000Z

227

Fabrication of solid oxide fuel cell by electrochemical vapor deposition  

DOE Patents (OSTI)

In a high temperature solid oxide fuel cell (SOFC), the deposition of an impervious high density thin layer of electrically conductive interconnector material, such as magnesium doped lanthanum chromite, and of an electrolyte material, such as yttria stabilized zirconia, onto a porous support/air electrode substrate surface is carried out at high temperatures (approximately 1100.degree.-1300.degree. C.) by a process of electrochemical vapor deposition. In this process, the mixed chlorides of the specific metals involved react in the gaseous state with water vapor resulting in the deposit of an impervious thin oxide layer on the support tube/air electrode substrate of between 20-50 microns in thickness. An internal heater, such as a heat pipe, is placed within the support tube/air electrode substrate and induces a uniform temperature profile therein so as to afford precise and uniform oxide deposition kinetics in an arrangement which is particularly adapted for large scale, commercial fabrication of SOFCs.

Brian, Riley (Willimantic, CT); Szreders, Bernard E. (Oakdale, CT)

1989-01-01T23:59:59.000Z

228

Fabrication of solid oxide fuel cell by electrochemical vapor deposition  

DOE Patents (OSTI)

In a high temperature solid oxide fuel cell (SOFC), the deposition of an impervious high density thin layer of electrically conductive interconnector material, such as magnesium doped lanthanum chromite, and of an electrolyte material, such as yttria stabilized zirconia, onto a porous support/air electrode substrate surface is carried out at high temperatures (/approximately/1100/degree/ /minus/ 1300/degree/C) by a process of electrochemical vapor deposition. In this process, the mixed chlorides of the specific metals involved react in the gaseous state with water vapor resulting in the deposit of an impervious thin oxide layer on the support tube/air electrode substrate of between 20--50 microns in thickness. An internal heater, such as a heat pipe, is placed within the support tube/air electrode substrate and induces a uniform temperature profile therein so as to afford precise and uniform oxide deposition kinetics in an arrangement which is particularly adapted for large scale, commercial fabrication of SOFCs.

Riley, B.; Szreders, B.E.

1988-04-26T23:59:59.000Z

229

Specific Mass Estimates for A Vapor Core Reactor With MHD  

SciTech Connect

This study investigated the development of a system concept for space power generation and nuclear electric propulsion based on a vapor core reactor (VCR) with magnetohydrodynamic (MHD) power conversion system, coupled to a magnetoplasma-dynamic (MPD) thruster. The VCR is a liquid-vapor core reactor concept operating with metallic uranium or uranium tetrafluoride (UF{sub 4}) vapor as the fissioning fuel and alkali metals or their fluorides as working fluid in a closed Rankine cycle with MHD energy conversion. Gaseous and liquid-vapor core reactors can potentially provide the highest reactor and cycle temperature among all existing or proposed fission reactor designs. This unique feature makes this reactor concept a very natural and attractive candidate for very high power (10 to 1000 MWe) and low specific mass (0.4 to 5 kg/kWe) nuclear electric propulsion (NEP) applications since the MHD output could be coupled with minimal power conditioning to MPD thrusters or other types of thruster for producing thrust at very high specific impulse (I{sub sp} 1500 to 10,000 s). The exceptional specific mass performance of an optimized VCRMHD- NEP system could lead to a dramatic reduction in the cost and duration of manned or robotic interplanetary as well as interstellar missions. The VCR-MHD-NEP system could enable very efficient Mars cargo transfers or short (<8 month) Mars round trips with less initial mass in low Earth orbit (IMLEO). The system could also enable highly efficient lunar cargo transfer and rapid missions to other destinations throughout the solar system. (authors)

Knight, Travis; Smith, Blair; Anghaie, Samim [Innovative Nuclear Space Power and Propulsion Institute (INSPI), PO Box 116502, University of Florida, Gainesville, FL 32611-6502 (United States)

2002-07-01T23:59:59.000Z

230

Heat Recovery in Distillation by Mechanical Vapor Recompression  

E-Print Network (OSTI)

be classified generally into two types,.aerodynamic and positive displacement (Figure 5). Among the various types of compressors, centrifugal, reciprocating, lobe and screw have been used for vapor recompression. I AXIAL AERODYNAMIC I I CENTRIFUGAL I... speeds of centri fugal compressors make them highly susceptible to erosion from entrained liquid droplets. This ero sion can reduce the efficiency and cause dynamic instability from rotor imbalance and mechanical failure. Next, it is important...

Becker, F. E.; Zakak, A. I.

231

High average power magnetic modulator for metal vapor lasers  

DOE Patents (OSTI)

A three-stage magnetic modulator utilizing magnetic pulse compression designed to provide a 60 kV pulse to a copper vapor laser at a 4.5 kHz repetition rate is disclosed. This modulator operates at 34 kW input power. The circuit includes a step up auto transformer and utilizes a rod and plate stack construction technique to achieve a high packing factor.

Ball, Don G. (Livermore, CA); Birx, Daniel L. (Oakley, CA); Cook, Edward G. (Livermore, CA); Miller, John L. (Livermore, CA)

1994-01-01T23:59:59.000Z

232

Methanol vaporization and injection system for internal combustion engine  

SciTech Connect

An engine equipped with an alcohol vaporization injection system operates as a four stroke cycle diesel engine that transfers the heat of exiting exhaust gases and cylinder head walls to the fuel. The engine runs on alcohol. The alcohol becomes vaporized and its pressure is high enough so that when a valve is opened between the high pressure fuel line and the combustion chamber (when it is at the peak of its compression ratio) enough alcohol will enter the combustion chamber to allow proper combustion. The overall advantages to this type of alcohol vaporization injection system is that it adds relatively few new mechanisms to the spark ignition four cycle internal combustion engine to enable it to operate as a diesel engine with a high thermal efficiency. This alcohol injection system exploits the engine's need for greater volumes of alcohol caused by the alcohol's relatively low heat of combustion (When compared to gasoline) by using this greater volume of fuel to return greater quantities of heat back to the engine to a much greater degree than other fuels can.

Bayley, R.I.

1980-05-06T23:59:59.000Z

233

Program plan for the resolution of tank vapor issues  

SciTech Connect

Since 1987, workers at the Hanford Site waste tank farms in Richland, Washington, have reported strong odors emanating from the large, underground high-level radioactive waste storage tanks. Some of these workers have complained of symptoms (e.g., headaches, nausea) related to the odors. In 1992, the U.S. Department of Energy, which manages the Hanford Site, and Westinghouse Hanford Company determined that the vapor emissions coming from the tanks had not been adequately characterized and represented a potential health risk to workers in the immediate vicinity of the tanks. At that time, workers in certain areas of the tank farms were required to use full-face, supplied-breathing-air masks to reduce their exposure to the fugitive emissions. While use of supplied breathing air reduced the health risks associated with the fugitive emissions, it introduced other health and safety risks (e.g., reduced field of vision, air-line tripping hazards, and heat stress). In 1992, an aggressive program was established to assure proper worker protection while reducing the use of supplied breathing air. This program focuses on characterization of vapors inside the tanks and industrial hygiene monitoring in the tank farms. If chemical filtration systems for mitigation of fugitive emissions are deemed necessary, the program will also oversee their design and installation. This document presents the plans for and approach to resolving the Hanford Site high-level waste tank vapor concerns. It is sponsored by the Department of Energy Office of Environmental Restoration and Waste Management.

Osborne, J.W.; Huckaby, J.L.

1994-05-01T23:59:59.000Z

234

The influence of prestrained metalorganic vapor phase epitaxial gallium-nitride templates on hydride vapor phase epitaxial growth  

Science Journals Connector (OSTI)

We have varied the strain situation in metalorganic vapor phase epitaxial (MOVPE) grown gallium-nitride (GaN) by exchanging the nucleation layer and by inserting a submono-Si x N y -interlayer in the first few hundred nanometers of growth on sapphire substrates. The influence on the MOVPE template and subsequent hydride vapor phase epitaxial (HVPE) growth could be shown by in-situ measurements of the sample curvature. Using the results of these investigations we have established a procedure to confine the curvature development in MOVPE and HVPE growth to a minimum. By increasing the layer thickness in HVPE we could create self-separated freestanding GaN layers with small remaining curvature.

2014-01-01T23:59:59.000Z

235

Tank 241-TX-118 headspace gas and vapor characterization results for samples collected in September 1994 and December 1994  

SciTech Connect

Significant changes have been made to all of the original vapor characterization reports. This report documents specific headspace gas and vapor characterization results for all vapor sampling events to date. In addition, changes have been made to the original vapor reports to qualify the data based on quality assurance issues associated with the performing laboratories

Huckaby, J.L. [Pacific Northwest Lab., Richland, WA (United States); Bratzel, D.R. [Westinghouse Hanford Co., Richland, WA (United States)

1995-09-27T23:59:59.000Z

236

Headspace vapor characterization of Hanford Waste Tank 241-T-110: Results from samples collected on August 31, 1995. Tank Vapor Characterization Project  

SciTech Connect

This report describes the results of vapor samples taken from the headspace of waste storage tank 241-T-110 (Tank T-110) at the Hanford Site in Washington State. Pacific Northwest National Laboratory (PNNL) contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed by the PNNL Vapor Analytical Laboratory (VAL) by the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was {open_quotes}Vapor Sampling and Analysis Plan{close_quotes}, and the sample job was designated S5056. Samples were collected by WHC on August 31, 1995, using the Vapor Sampling System (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace.

McVeety, B.D.; Thomas, B.L.; Evans, J.C. [and others

1996-05-01T23:59:59.000Z

237

Final Report for ARM Project Measuring 4-D Water Vapor Fields with GPS  

SciTech Connect

Water vapor is a primary element in the Earth’s climate system. Atmospheric water vapor is central to cloud processes, radiation transfer, and the hydrological cycle. Using funding from Department of Energy (DOE) grant DE-FG03-02ER63327, the University Corporation for Atmospheric Research (UCAR) developed new observational techniques to measure atmospheric water vapor and applied these techniques to measure four dimensional water vapor fields throughout the United States Southern Great Plains region. This report summarizes the development of a new observation from ground based Global Positioning System (GPS) stations called Slant Water Vapor (SW) and it’s utilization in retrieving four dimensional water vapor fields. The SW observation represents the integrated amount of water vapor between a GPS station and a transmitting satellite. SW observations provide improved temporal and spatial sampling of the atmosphere when compared to column-integrated quantities such as preciptitable water vapor (PW). Under funding from the DOE Atmospheric Radiation Measurement (ARM) program, GPS networks in the Southern Great Plains (SGP) region were deployed to retrieve SW to improve the characterization of water vapor throughout the region. These observations were used to estimate four dimensional water vapor fields using tomographic approaches and through assimilation into the MM5 numerical weather model.

Braun, John

2006-02-06T23:59:59.000Z

238

ARM - Facility News Article  

NLE Websites -- All DOE Office Websites (Extended Search)

Arctic Winter Water Vapor IOP Starts; Microwave Radiometer Profiler Arctic Winter Water Vapor IOP Starts; Microwave Radiometer Profiler Deployed Bookmark and Share Some of the instruments collecting data during the Arctic Winter Water Vapor IOP include ARM's microwave radiometer profiler (left) and microwave radiometer (right), and NOAA's ground-based scanning radiometer (middle). Some of the instruments collecting data during the Arctic Winter Water Vapor IOP include ARM's microwave radiometer profiler (left) and microwave radiometer (right), and NOAA's ground-based scanning radiometer (middle). The Arctic Winter Water Vapor Intensive Operational Period (IOP), a collaborative effort with the National Oceanic and Atmospheric Administration (NOAA) Environmental Technology Laboratory, began on March 10 in Barrow, Alaska. The major goal of the Arctic Winter Water Vapor IOP

239

Mercury Vapor At Salt Wells Area (Henkle, Et Al., 2005) | Open Energy  

Open Energy Info (EERE)

Mercury Vapor At Salt Wells Area (Henkle, Et Al., 2005) Mercury Vapor At Salt Wells Area (Henkle, Et Al., 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Salt Wells Area (Henkle, Et Al., 2005) Exploration Activity Details Location Salt Wells Area Exploration Technique Mercury Vapor Activity Date - 2005 Usefulness useful DOE-funding Unknown Exploration Basis Adsorbed mercury soil geochemical surveys and radiometric geophysical surveys were carried out in conjunction with geologic mapping to test the application of these ground-based techniques to geothermal exploration at three prospects in Nevada by Henkle Jr. et al. in 2005. Mercury soil vapor surveys were not widely used in geothermal exploration in the western US at the time, although the association of mercury vapors with geothermal

240

Chemical vapor deposition of amorphous semiconductor films. Final subcontract report  

SciTech Connect

Chemical vapor deposition (CVD) from higher order silanes has been studied for fabricating amorphous hydrogenated silicon thin-film solar cells. Intrinsic and doped a-Si:H films were deposited in a reduced-pressure, tubular-flow reactor, using disilane feed-gas. Conditions for depositing intrinsic films at growth rates up to 10 A/s were identified. Electrical and optical properties, including dark conductivity, photoconductivity, activation energy, optical absorption, band-gap and sub-band-gap absorption properties of CVD intrinsic material were characterized. Parameter space for depositing intrinsic and doped films, suitable for device analysis, was identified.

Rocheleau, R.E.

1984-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

A thermoacoustic oscillator powered by vaporized water and ethanol  

Science Journals Connector (OSTI)

We measure the temperature difference required to drive a thermoacoustic oscillator containing air water vapor and liquid water as the working fluids. The oscillator is composed of a large tube containing an array of narrow tubes connected at one end to a tank of liquid water. When the water is heated the temperature difference across the tube array increases until thermoacoustic oscillations occur. The temperature difference at the onset of oscillation is measured to be 56 ? ° C significantly smaller (by ? 200 ? ° C ) than the temperature measured when the tank is filled with dry air instead of water. The temperature difference can be further reduced to 47 ? ° C by using ethanol instead of water.

Daisuke Noda; Yuki Ueda

2013-01-01T23:59:59.000Z

242

Io - Are vapor explosions responsible for the 5-micron outbursts  

SciTech Connect

It is proposed that a vapor explosion of a submerged pool of liquid sulfur will remove the crust overlying an area of about 50-km diam. Thermal radiation from the exposed liquid sulfur pool with a surface temperature of 600 K is then presumed to be responsible for the 5-micron outbursts that have been observed. The explosive volcanoes are expected to leave black sulfur calderas, which are, indeed, found on the surface. The 5-micron outburst observed by Sinton (1980), on June 11, 1979 (UT), is identified with a new caldera found on Voyager 2 photographs but which had not been present on Voyager 1 pictures.

Sinton, W.M.

1980-01-01T23:59:59.000Z

243

Optical waveguides in SBN by zinc vapor diffusion  

E-Print Network (OSTI)

at 600'C for a 12. 5 i1m Wide 1000'C Zinc Vapor Diffused SBN:60 Waveguide Measured at X = 0. 81 pm. IV. SBN:60 Amplitude Modulator Results . . . . . V. SBN:60 Mach-Zehnder Interferometer Results. . . . VI. Voltage-Length Product Comparison...: (a) extraordinary (TM), (b) 1. 5 x ordinary (TE). 12. Surface damage on SBN:60 diffused at 1000'C with an SiOz diffusion mask. 13. Zinc in-diffusion in SBN:60 25 . . . . . 26 . . . . . 27 . . . . . 28 29 14. Barium out-diffuison in SBN:60...

Quinn, Jeffrey Dale

1991-01-01T23:59:59.000Z

244

Combustion chemical vapor deposited coatings for thermal barrier coating systems  

SciTech Connect

The new deposition process, combustion chemical vapor deposition, shows a great deal of promise in the area of thermal barrier coating systems. This technique produces dense, adherent coatings, and does not require a reaction chamber. Coatings can therefore be applied in the open atmosphere. The process is potentially suitable for producing high quality CVD coatings for use as interlayers between the bond coat and thermal barrier coating, and/or as overlayers, on top of thermal barrier coatings. In this report, the evaluation of alumina and ceria coatings on a nickel-chromium alloy is described.

Hampikian, J.M.; Carter, W.B. [Georgia Institute of Technology, Atlanta, GA (United States). School of Materials Science and Engineering

1995-12-31T23:59:59.000Z

245

Unusual thermopower of inhomogeneous graphene grown by chemical vapor deposition  

SciTech Connect

We report on thermopower (TEP) and resistance measurements of inhomogeneous graphene grown by chemical vapor deposition (CVD). Unlike the conventional resistance of pristine graphene, the gate-dependent TEP shows a large electron-hole asymmetry. This can be accounted for by inhomogeneity of the CVD-graphene where individual graphene regions contribute with different TEPs. At the high magnetic field and low temperature, the TEP has large fluctuations near the Dirac point associated with the disorder in the CVD-graphene. TEP measurements reveal additional characteristics of CVD-graphene, which are difficult to obtain from the measurement of resistance alone.

Nam, Youngwoo, E-mail: youngwoo.nam@chalmers.se [Department of Physics and Astronomy, Seoul National University, Seoul 151-747 (Korea, Republic of); Department of Microtechnology and Nanoscience, Chalmers University of Technology, SE-412 96 Gothenburg (Sweden); Sun, Jie; Lindvall, Niclas; Yurgens, August [Department of Microtechnology and Nanoscience, Chalmers University of Technology, SE-412 96 Gothenburg (Sweden); Jae Yang, Seung; Rae Park, Chong [Department of Materials Science and Engineering, Seoul National University, Seoul 151-747 (Korea, Republic of); Woo Park, Yung [Department of Physics and Astronomy, Seoul National University, Seoul 151-747 (Korea, Republic of)

2014-01-13T23:59:59.000Z

246

Dosimeter for monitoring vapors and aerosols of organic compounds  

DOE Patents (OSTI)

A dosimeter is provided for collecting and detecting vapors and aerosols of organic compounds. The dosimeter comprises a lightweight, passive device that can be conveniently worn by a person as a badge or placed at a stationary location. The dosimeter includes a sample collector comprising a porous web treated with a chemical for inducing molecular displacement and enhancing phosphorescence. Compounds are collected onto the web by molecular diffusion. The web also serves as the sample medium for detecting the compounds by a room temperature phosphorescence technique. 7 figs.

Vo-Dinh, T.

1987-07-14T23:59:59.000Z

247

The Prospects of Alternatives to Vapor Compression Technology for Space Cooling and Food Refrigeration Applications  

SciTech Connect

Five alternatives to vapor compression technology were qualitatively evaluated to determine their prospects for being better than vapor compression for space cooling and food refrigeration applications. The results of the assessment are summarized in the report. Overall, thermoacoustic and magnetic technologies were judged to have the best prospects for competing with vapor compression technology, with thermotunneling, thermoelectric, and thermionic technologies trailing behind in that order.

Brown, Daryl R.; Dirks, James A.; Fernandez, Nicholas; Stout, Tyson E.

2010-03-31T23:59:59.000Z

248

A thermodynamics based analysis of exergy destruction in vapor compression cycle systems.  

E-Print Network (OSTI)

??In the last few decades, vapor-compression cycle systems (VCSs) have undergone many advances in actuation, allowing for variable aperture valves, variable speed compressors, and variable… (more)

Kania, Megan

2013-01-01T23:59:59.000Z

249

Synthesis and Characterization of Magnetic Nanowires Prepared by Chemical Vapor Deposition.  

E-Print Network (OSTI)

??Various metal silicide and germanide magnetic nanowires were synthesized using a home-built CVD [chemical vapor deposition] system. The morphology, composition, and magnetic properties of the… (more)

Tang, Siwei

2014-01-01T23:59:59.000Z

250

Liquid fuel vaporizer and combustion chamber having an adjustable thermal conductor  

DOE Patents (OSTI)

The efficiency and effectiveness of apparatuses for vaporizing and combusting liquid fuel can be improved using thermal conductors. For example, an apparatus having a liquid fuel vaporizer and a combustion chamber can be characterized by a thermal conductor that conducts heat from the combustion chamber to the vaporizer. The thermal conductor can be a movable member positioned at an insertion depth within the combustion chamber that corresponds to a rate of heat conduction from the combustion chamber to the vaporizer. The rate of heat conduction can, therefore, be adjusted by positioning the movable member at a different insertion depth.

Powell, Michael R; Whyatt, Greg A; Howe, Daniel T; Fountain, Matthew S

2014-03-04T23:59:59.000Z

251

Stable-Isotope Studies Of Rocks And Secondary Minerals In A Vapor...  

Open Energy Info (EERE)

Stable-Isotope Studies Of Rocks And Secondary Minerals In A Vapor-Dominated Hydrothermal System At The Geysers, Sonoma County, California Jump to: navigation, search GEOTHERMAL...

252

The Patuha geothermal system: a numerical model of a vapor-dominated system.  

E-Print Network (OSTI)

??The Patuha geothermal system is a vapor-dominated reservoir located about 40 kilometers southwest of Bandung on western Java, Indonesia. The geothermal system consists of a… (more)

Schotanus, M.R.J.

2013-01-01T23:59:59.000Z

253

E-Print Network 3.0 - alkali atom vapor Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

a vapor cell magneto-optical trap. 1999 American... to the vacuum pumps or due to adsorption of the ... Source: Jin, Deborah - JILA, University of Colorado at Boulder...

254

Removal of hydrogen sulfide as ammonium sulfate from hydropyrolysis product vapors  

SciTech Connect

A system and method for processing biomass into hydrocarbon fuels that includes processing a biomass in a hydropyrolysis reactor resulting in hydrocarbon fuels and a process vapor stream and cooling the process vapor stream to a condensation temperature resulting in an aqueous stream. The aqueous stream is sent to a catalytic reactor where it is oxidized to obtain a product stream containing ammonia and ammonium sulfate. A resulting cooled product vapor stream includes non-condensable process vapors comprising H.sub.2, CH.sub.4, CO, CO.sub.2, ammonia and hydrogen sulfide.

Marker, Terry L; Felix, Larry G; Linck, Martin B; Roberts, Michael J

2014-10-14T23:59:59.000Z

255

Response of passive organic vapor dosimeters to a mixed gas exposure  

E-Print Network (OSTI)

of Advisory Comm1ttee: Dr. Richard B. Konzen The effects of the sampling order of two chemicals adsorbed onto a DuPont Pro-Tek Organic Vapor Dosimeters were investigated. The dosimeters were exposed to varying known concentrations of methyl methacrylate...-powered pump to draw a known volume of air through a charcoal packed tube. The charcoal adsorbs the organic vapors and separates the small amount of vapor from a large amount of air. The organic vapors are then desorbed and analyzed by means of gas...

Anderson, Scott Merritt

2012-06-07T23:59:59.000Z

256

Low-Cost, Modular Electrothermal Vaporization System for Inductively Coupled Plasma Atomic Emission Spectrometry  

Science Journals Connector (OSTI)

In this investigation, commercially available tungsten filaments were employed to electrothermally vaporize liquid samples prior to their introduction into an inductively coupled...

Levine, Keith; Wagner, Karl A; Jones, Bradley T

1998-01-01T23:59:59.000Z

257

E-Print Network 3.0 - atomic vapor deposited Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

Articles Surfactant-Catalyzed Chemical Vapor Deposition of Copper Thin Films Eui Seong Hwang... and demonstrated for deposition of copper thin films from ... Source:...

258

E-Print Network 3.0 - acoustic wave vapor Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

(6). While previous systems have demonstrated success in chemical... striking visual identification of a range of ligating vapors (including alcohols, amines, ethers... ,...

259

Advanced Organic Vapor Cycles for Improving Thermal Conversion Efficiency in Renewable Energy Systems.  

E-Print Network (OSTI)

??The Organic Flash Cycle (OFC) is proposed as a vapor power cycle that could potentially increase power generation and improve the utilization efficiency of renewable… (more)

Ho, Tony

2012-01-01T23:59:59.000Z

260

Towards improved spinnability of chemical vapor deposition generated multi-walled carbon nanotubes  

E-Print Network (OSTI)

P. J. F. 1999 Carbon nanotubes and related structures: newof vapor grown carbon nanotubes and single wall nanotubes, Eto Carbon Materials in Carbon Nanotubes: Preparation and

McKee, Gregg Sturdivant Burke

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Opals infiltrated with a stimuli-responsive hydrogel for ethanol vapor sensing  

Science Journals Connector (OSTI)

We report on a novel class of optical materials for ethanol vapor sensing, based on polystyrene opals infiltrated with an innovative stimuli-responsive hydrogel. We describe the...

Pernice, Riccardo; Adamo, Gabriele; Stivala, Salvatore; Parisi, Antonino; Busacca, Alessandro C; Spigolon, Dario; Sabatino, Maria Antonietta; D’Acquisto, Leonardo; Dispenza, Clelia

2013-01-01T23:59:59.000Z

262

Gas chromatographic-mass spectrometric characterization of an oil aerosol-vapor microbial disinfectant .  

E-Print Network (OSTI)

??"This thesis focuses on chemical characterization studies of disinfectant vapors generated from thermal oxidation of mineral oil and biogenic oil esters. The disinfection technique holds… (more)

Wadhwa, Prakash, 1980-

2005-01-01T23:59:59.000Z

263

Prediction of blast damage from vapor cloud explosions  

SciTech Connect

The process industries handle a wide range of different materials and use them in different types of chemical reaction. Of particular concern is the prospect of damage and injury affecting the general public outside the boundary wall of the chemical plant. It is not wise to permit the construction of homes, schools or hospitals so close to chemical plants that they, and the people within, might be damaged or injured should there be an accidental explosion in the plant. The major hazard outside the plant is over-pressure, a consequence of an accidental explosion in a cloud of flammable gas or vapor (Vapor Cloud Explosion or VCE). It is the responsibility of plant management to ensure that any such accidental explosion is not so large as to endanger the public, and of the local planning authorities to ensure that homes, schools or hospitals are not sited so close to chemical plants that they may be endangered by accidental explosion. A vital tool for such authorities is a simple method of assessing the possible consequences of an accidental VCE. In this paper those methods of assessing the consequences are examined.

Phillips, H. [Phillips (H.), Buxton (United Kingdom)

1995-12-31T23:59:59.000Z

264

Method of physical vapor deposition of metal oxides on semiconductors  

DOE Patents (OSTI)

A process for growing a metal oxide thin film upon a semiconductor surface with a physical vapor deposition technique in a high-vacuum environment and a structure formed with the process involves the steps of heating the semiconductor surface and introducing hydrogen gas into the high-vacuum environment to develop conditions at the semiconductor surface which are favorable for growing the desired metal oxide upon the semiconductor surface yet is unfavorable for the formation of any native oxides upon the semiconductor. More specifically, the temperature of the semiconductor surface and the ratio of hydrogen partial pressure to water pressure within the vacuum environment are high enough to render the formation of native oxides on the semiconductor surface thermodynamically unstable yet are not so high that the formation of the desired metal oxide on the semiconductor surface is thermodynamically unstable. Having established these conditions, constituent atoms of the metal oxide to be deposited upon the semiconductor surface are directed toward the surface of the semiconductor by a physical vapor deposition technique so that the atoms come to rest upon the semiconductor surface as a thin film of metal oxide with no native oxide at the semiconductor surface/thin film interface. An example of a structure formed by this method includes an epitaxial thin film of (001)-oriented CeO.sub.2 overlying a substrate of (001) Ge.

Norton, David P. (Knoxville, TN)

2001-01-01T23:59:59.000Z

265

Investigation of Pool Spreading and Vaporization Behavior in Medium-Scale LNG Tests  

Science Journals Connector (OSTI)

Abstract A failure of a Liquefied Natural Gas (LNG) tanker can occur due to collision or loading/unloading operation resulting in spillage of LNG on water. Upon release, a spreading liquid can form a pool with rapid vaporization leading to the formation of a flammable vapor cloud. Safety analysis for the protection of public and property involves the determination of consequences of such accidental releases. To address this complex pool spreading and vaporization phenomenon of LNG, an investigation is performed based on the experimental tests that were conducted by the Mary Kay O’Connor Process Safety Center (MKOPSC) in 2007. The 2007 tests are a part of medium-scale experiments carried out at the Brayton Fire Training Field (BFTF), College Station. The dataset represents a semi-continuous spill on water, where LNG is released on a confined area of water for a specified duration of time. The pool spreading and vaporization behavior are validated using empirical models, which involved determination of pool spreading parameters and vaporization rates with respect to time. Knowledge of the pool diameter, pool height and spreading rate are found to be important in calculating the vaporization rates of the liquid pool. The paper also presents a method to determine the vaporization mass flux of LNG using water temperature data that is recorded in the experiment. The vaporization rates are observed to be high initially and tend to decrease once the pool stopped spreading. The results of the analysis indicated that a vaporization mass flux that is varying with time is required for accurate determination of the vaporization rate. Based on the data analysis, sources of uncertainties in the experimental data were identified to arise from ice formation and vapor blocking.

Nirupama Gopalaswami; R. Mentzer; M. Sam Mannan

2014-01-01T23:59:59.000Z

266

Evaluation of the Vaporization, Fusion, and Sublimation Enthalpies of the 1-Alkanols: The Vaporization Enthalpy of 1-, 6-, 7-, and 9-Heptadecanol,  

E-Print Network (OSTI)

Evaluation of the Vaporization, Fusion, and Sublimation Enthalpies of the 1-Alkanols* Department of Chemistry and Biochemistry, University of MissourisSt. Louis, St. Louis, Missouri 63121 sublimation enthalpies. The sublimation enthalpies were compared to existing literature values. Agreement

Chickos, James S.

267

Advanced Membrane Systems: Recovering Wasteful and Hazardous Fuel Vapors at the Gasoline Tank  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CMS to develop a membrane CMS to develop a membrane vapor processor that recovers fuel vapors from gasoline refueling with 99 percent efficiency. This membrane system enables gasoline stations to surpass environmental regulations while reducing fuel losses. Compact Membrane Systems, Inc. (CMS) was founded in 1993 in Wilmington, DE, with the acquisition of rights to certain DuPont polymer membrane patents. CMS focuses

268

An Examination of the Thermodynamics of Fusion, Vaporization, and Sublimation of Several Parabens by Correlation Gas  

E-Print Network (OSTI)

An Examination of the Thermodynamics of Fusion, Vaporization, and Sublimation of Several Parabens, Kasetsart University, Bangkane, Bangkok 10900, Thailand 2 Department of Chemistry and Biochemistry.com). DOI 10.1002/jps.22423 ABSTRACT: The vaporization, fusion, and sublimation enthalpies of methyl, ethyl

Chickos, James S.

269

Method and apparatus to measure vapor pressure in a flow system  

DOE Patents (OSTI)

The present invention is directed to a method for determining, by a condensation method, the vapor pressure of a material with a known vapor pressure versus temperature characteristic, in a flow system particularly in a mercury isotope enrichment process. 2 figures.

Grossman, M.W.; Biblarz, O.

1991-10-15T23:59:59.000Z

270

Apparatus and method for removing mercury vapor from a gas stream  

DOE Patents (OSTI)

A metallic filter effectively removes mercury vapor from gas streams. The filter captures the mercury which then can be released and collected as product. The metallic filter is a copper mesh sponge plated with a six micrometer thickness of gold. The filter removes up to 90% of mercury vapor from a mercury contaminated gas stream.

Ganesan, Kumar (Butte, MT)

2008-01-01T23:59:59.000Z

271

Determination of effective water vapor diffusion coefficient in pemfc gas diffusion layers  

E-Print Network (OSTI)

route from the cathode catalyst layer to the cathode flow channels. Water can be removed from the cellDetermination of effective water vapor diffusion coefficient in pemfc gas diffusion layers Jacob M: Water vapor diffusion PEMFC Water management GDL Diffusivity MPL a b s t r a c t The primary removal

Kandlikar, Satish

272

Optofluidic ring resonator sensors for rapid DNT vapor detection Greg Frye-Mason,b  

E-Print Network (OSTI)

(OFRR) chemical vapor sensor as a promising platform for explosive detection with the capability and chemical sensing platform.23­27 As illustrated in Fig. 1(A), the OFRR is a thin-walled fused silica shows that the OFRR vapor sensor is a promising platform for the development of a rapid, low

Fan, Xudong "Sherman"

273

Retrieval of water vapor profiles over ocean using SSM/I and SSM/T-2  

E-Print Network (OSTI)

of water vapor profiles, while the SSM/I can be used to retrieve, among other things, the total integrated water vapor (TIWV) in a column of air. It is theoretically possible to use SSM/I data to supplement the SSM/T-2 data, producing more accurate water...

Blankenship, Clay Bruce

2012-06-07T23:59:59.000Z

274

Researchers develop electrodeposition process to deposit coatings on substrates, eliminate the expensive physical vapor  

E-Print Network (OSTI)

the expensive physical vapor deposition step, and improve device quality. CuIn1-xGaxSe2 (CIGS) solar cells have composition was adjusted by physical vapor deposition method. At present, we are fabricating CIGS-based solar). 2 R. N. Bhattacharya, W. Batchelor, J. F. Hiltner, and J. R. Sites, Appl. Phys. Lett., 75, 1431

275

Indium and tellurium doping of CdS crystals in cadmium vapor and their luminescent properties  

Science Journals Connector (OSTI)

A technique is devised for vapor-phase doping of CdS in the quaternary system Cd-In-Te-S. CdS crystals are doped with In and Te via four-zone ... InTe vapors. The luminescence spectra of the CdS?In,Te?[Cd] crysta...

I. N. Odin; M. V. Chukichev; M. E. Rubina

276

Indium and tellurium doping of CdS crystals in cadmium vapor and their luminescent properties  

Science Journals Connector (OSTI)

—A technique is devised for vapor-phase doping of CdS in the quaternary system Cd—In—Te—S. CdS crystals are doped with In and Te via four-zone ... InTe vapors. The luminescence spectra of the CdS?In,Te?[Cd] cryst...

I. N. Odin; M. V. Chukichev; M. E. Rubina

277

Vapor phase elemental sulfur amendment for sequestering mercury in contaminated soil  

DOE Patents (OSTI)

The process of treating elemental mercury within the soil is provided by introducing into the soil a heated vapor phase of elemental sulfur. As the vapor phase of elemental sulfur cools, sulfur is precipitated within the soil and then reacts with any elemental mercury thereby producing a reaction product that is less hazardous than elemental mercury.

Looney, Brian B.; Denham, Miles E.; Jackson, Dennis G.

2014-07-08T23:59:59.000Z

278

Nickel catalyst faceting in plasma-enhanced direct current chemical vapor deposition of carbon nanofibers  

E-Print Network (OSTI)

1 Nickel catalyst faceting in plasma-enhanced direct current chemical vapor deposition of carbon vapor deposition with Ni catalysts on the top of nanofibers. Transmission electron microscopy was used to study the morphology and crystallography of Ni catalysts, which are essential for the nucleation

Paris-Sud XI, Université de

279

Neural modeling of vapor compression refrigeration cycle with extreme learning machine  

Science Journals Connector (OSTI)

In this paper, a single-hidden layer feed-forward neural network (SLFN) is used to model the dynamics of the vapor compression cycle in refrigeration and air-conditioning systems, based on the extreme learning machine (ELM). It is shown that the assignment ... Keywords: Back propagation, Extreme learning machine, Modeling, Radial basis function, Support vector regression, Vapor compression refrigeration cycle

Lei Zhao; Wen-Jian Cai; Zhi-Hong Man

2014-03-01T23:59:59.000Z

280

Chem. Mater. 1995, 7, 2269-2272 2269 Water Vapor Adsorption on Chemically Treated  

E-Print Network (OSTI)

Chem. Mater. 1995, 7, 2269-2272 2269 Water Vapor Adsorption on Chemically Treated Activated Carbon August 25, 1995@ Water vapor adsorption on activated carbon cloth (ACCBO)which has been oxidized% Cl), and ACCBO (4% N), exhibits sigmoidal isotherms with hysteresis loops of varying magnitudes

Cal, Mark P.

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Cloud and Aerosol Properties, Precipitable Water, and Profiles of Temperature and Water Vapor from MODIS  

E-Print Network (OSTI)

Cloud and Aerosol Properties, Precipitable Water, and Profiles of Temperature and Water Vapor from such as cloud mask, atmos- pheric profiles, aerosol properties, total precipitable water, and cloud properties vapor amount, aerosol particles, and the subsequently formed clouds [9]. Barnes et al. [2] provide

Sheridan, Jennifer

282

Tunneling characteristics in chemical vapor deposited graphene hexagonal boron nitride graphene junctions  

E-Print Network (OSTI)

1 Tunneling characteristics in chemical vapor deposited graphene ­ hexagonal boron nitride ­ graphene junctions T. Roy1 , L. Liu2 , S. de la Barrera,3 B. Chakrabarti1,4 , Z. R. Hesabi1 , C. A. Joiner1 Abstract: Large area chemical vapor deposited graphene and hexagonal boron nitride was used to fabricate

Feenstra, Randall

283

Computational Analysis and Optimization of a Chemical Vapor Deposition Reactor with  

E-Print Network (OSTI)

Computational Analysis and Optimization of a Chemical Vapor Deposition Reactor with Large and optimization of a three- dimensional model of a horizontal chemical vapor deposition (CVD) reactor used National Laboratories February 9, 2004 Abstract A computational analysis and optimization is presented

284

Optimization of the chemical vapor deposition process for carbon nanotubes fabrication  

E-Print Network (OSTI)

Optimization of the chemical vapor deposition process for carbon nanotubes fabrication M. Grujicica-phase chemistry and surface chemistry model is developed to analyze, at the reactor length scale, chemical vapor (carrier gas) in the presence of cobalt catalytic particles in a cylindrical reactor. The model allows

Grujicic, Mica

285

OPTIMAL DESIGN OF A HIGH PRESSURE ORGANOMETALLIC CHEMICAL VAPOR DEPOSITION REACTOR  

E-Print Network (OSTI)

OPTIMAL DESIGN OF A HIGH PRESSURE ORGANOMETALLIC CHEMICAL VAPOR DEPOSITION REACTOR K.J. BACHMANN of computer simulations as an optimal design tool which lessens the costs in time and effort in experimental vapor deposition (HPOMCVD) reactor for use in thin film crystal growth. The advantages of such a reactor

286

On the optimization of a dc arcjet diamond chemical vapor deposition reactor  

E-Print Network (OSTI)

On the optimization of a dc arcjet diamond chemical vapor deposition reactor S. W. Reevea) and W. A precursor in our dc arcjet reactor.1 Based on conclusions drawn from that work, an optimization strategy diamond film growth in a dc arcjet chemical vapor deposition reactor has been developed. Introducing

Dandy, David

287

Fundamental process and system design issues in CO2 vapor compression systems  

E-Print Network (OSTI)

Fundamental process and system design issues in CO2 vapor compression systems Man-Hoe Kima; CO2 (R-744); Transcritical cycle; Vapor compression system; COP; Air-conditioning; Heat pump recent developments and state of the art for transcritical CO2 cycle technology in various refrigeration

Bahrami, Majid

288

Laser vaporization/ionization interface for coupling microscale separation techniques with mass spectrometry  

DOE Patents (OSTI)

The present invention provides a laser-induced vaporization and ionization interface for directly coupling microscale separation processes to a mass spectrometer. Vaporization and ionization of the separated analytes are facilitated by the addition of a light-absorbing component to the separation buffer or solvent. 8 figs.

Yeung, E.S.; Chang, Y.C.

1999-06-29T23:59:59.000Z

289

Feasibility of UV lasing without inversion in mercury vapor  

E-Print Network (OSTI)

We investigate the feasibility of UV lasing without inversion at a wavelength of $253.7$ nm utilizing interacting dark resonances in mercury vapor. Our theoretical analysis starts with radiation damped optical Bloch equations for all relevant 13 atomic levels. These master equations are generalized by considering technical phase noise of the driving lasers. From the Doppler broadened complex susceptibility we obtain the stationary output power from semiclassical laser theory. The finite overlap of the driving Gaussian laser beams defines an ellipsoidal inhomogeneous gain distribution. Therefore, we evaluate the intra-cavity field inside a ring laser self-consistently with Fourier optics. This analysis confirms the feasibility of UV lasing and reveals its dependence on experimental parameters.

Martin R. Sturm; Benjamin Rein; Thomas Walther; Reinhold Walser

2014-06-27T23:59:59.000Z

290

Chemical vapor deposition of hydrogenated amorphous silicon from disilane  

SciTech Connect

The authors describe hydrogenated amorphous silicon (a-Si:H) thin films deposited at growth rates of 1 to 30 A/s by chemical vapor deposition (CVD) from disilane source gas at 24 torr total pressure in a tubular reactor. The effects of substrate temperature and gas holding time (flow rate) on film growth rate and effluent gas composition were measured at temperatures ranging from 360{sup 0} to 485{sup 0}C and gas holding times from 3 to 62s. Effluent gases determined by gas chromatography included silane, disilane and other higher order silanes. A chemical reaction engineering model, based on a silylene (SiH/sub 2/) insertion gas phase reaction network and film growth from both SiH/sub 2/ and high molecular weight silicon species, Si/sub n/H/sub 2n/, was developed. The model predictions were in good agreement with experimentally determined growth rates and effluent gas compositions.

Bogaert, R.J.; Russell, T.W.F.; Klein, M.T. (Delaware Univ., Newark, DE (USA). Dept. of Chemical Engineering); Rocheleau, R.E.; Baron, B.N. (Delaware Univ., Newark, DE (USA). Inst. of Energy Conversion)

1989-10-01T23:59:59.000Z

291

Chemical vapor deposition of boron-doped hydrogenated amorphous silicon  

SciTech Connect

Deposition conditions and film properties for a variety of boron-doped hydrogenated amorphous silicon films and silicon-carbon films produced by chemical vapor deposition (CVD) are discussed. Deposition gases include monosilane, disilane, trisilane, and acetylene. Two types of optically wide band-gap p layers are obtained. One of these window p layers (without carbon) has been extensively tested in photovoltaic devices. Remarkably, this p layer can be deposited between about 200 to 300 /sup 0/C. A typical open circuit voltage in an all CVD p-i-n device is 0.70--0.72 V, and in a hybrid device where the i and n layers are deposited by glow discharge, 0.8--0.83 V.

Ellis F.B. Jr.; Delahoy, A.E.

1985-07-15T23:59:59.000Z

292

Adsorption and Diffusion of Alcohol Vapors by Argonne Premium Coals  

Science Journals Connector (OSTI)

Adsorption and Diffusion of Alcohol Vapors by Argonne Premium Coals ... Adsorption of methanol, ethanol, n-propanol, and n-butanol by Pocahontas No. 3, Upper Freeport, Illinois No. 6, and Beulah-Zap Argonne premium coals was investigated to clarify the effect of alkyl group bulk on adsorption and to evaluate the micropore and cross-linked structure of coals. ... Coals are thought to have a large surface area with an interconnected network of slitlike pores.1 However, Larsen et al.2 measured the adsorption of various gases on five Argonne Premium coals and, except for Beulah-Zap lignite, found that the very steep dependence of BET surface area was related to the molecular volume of the gas. ...

Toshimasa Takanohashi; Yuki Terao; Takahiro Yoshida; Masashi Iino

2000-06-17T23:59:59.000Z

293

Homogeneous nucleation rate measurements in supersaturated water vapor  

Science Journals Connector (OSTI)

The rate of homogeneous nucleation in supersaturated vapors of water was studied experimentally using a thermal diffusion cloud chamber. Helium was used as a carrier gas. Our study covers a range of nucleation rates from 3 × 10 ? 1 to 3 × 10 2 cm ? 3 s ? 1 at four isotherms: 290 300 310 and 320 K . The molecular content of critical clusters was estimated from the slopes of experimental data. The measured isothermal dependencies of nucleation rate of water on saturation ratio were compared with the prediction of the classical theory of homogeneous nucleation the empirical prediction of Wölk et al. [J. Chem. Phys.117 10 (2002)] the scaled model of Hale [Phys. Rev. A33 4156 (1986)] and the former nucleation onset data.

David Brus; Vladimír Ždímal; Ji?í Smolík

2008-01-01T23:59:59.000Z

294

Strain relaxation in graphene grown by chemical vapor deposition  

SciTech Connect

The growth of single layer graphene by chemical vapor deposition on polycrystalline Cu substrates induces large internal biaxial compressive strain due to thermal expansion mismatch. Raman backscattering spectroscopy and atomic force microscopy were used to study the strain relaxation during and after the transfer process from Cu foil to SiO{sub 2}. Interestingly, the growth of graphene results in a pronounced ripple structure on the Cu substrate that is indicative of strain relaxation of about 0.76% during the cooling from the growth temperature. Removing graphene from the Cu substrates and transferring it to SiO{sub 2} results in a shift of the 2D phonon line by 27?cm{sup ?1} to lower frequencies. This translates into additional strain relaxation. The influence of the processing steps, used etching solution and solvents on strain, is investigated.

Troppenz, Gerald V., E-mail: gerald.troppenz@helmholtz-berlin.de; Gluba, Marc A.; Kraft, Marco; Rappich, Jörg; Nickel, Norbert H. [Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Institut für Silizium Photovoltaik, Kekuléstr. 5, D-12489 Berlin (Germany)

2013-12-07T23:59:59.000Z

295

Characterization of isothermal vapor phase epitaxial (Hg,Cd)Te  

Science Journals Connector (OSTI)

We report on the characterization of mercury cadmium telluride (Hg 1?x Cd x Te) film grown by the isothermal vapor phase epitaxial method (ISOVPE) and on the surface conversion of bulk Hg 1?xCd x Te to larger bandgap material. The crystal perfection is evaluated using defect etching electron beam and electrolyte electroreflectance (EBER and EER) and Rutherford backscattering spectrometry (RBS). Hall measurements are used to measure carrier densities and mobilities. Surface concentrations and concentration profiles are measured for the ISOVPE grown layers by transmission Fourier transform infrared spectroscopy (FTIR) and electron?probe microanalysis (EPMA) to establish quantitative informations about composition control. Metal–insulator?semiconductor (MIS) structures were made and the properties important to device performance such as compositional uniformity storage time and carrier concentration are measured. The ISOVPE layers are compared in quality to films grown by other methods and show promise for MIS devices.

S. B. Lee; L. K. Magel; M. F. S. Tang; D. A. Stevenson; J. H. Tregilgas; M. W. Goodwin; R. L. Strong

1990-01-01T23:59:59.000Z

296

Inelastic Scattering of 20-kev Electrons in Metal Vapors  

Science Journals Connector (OSTI)

The low-energy losses of 20-kev electrons passing through the vapors of Zn, Cd, Hg, Na, K, Mg, Ca, Sb, Pb, and KCl, have been measured by using an electrostatic analyzer previously used for measuring electron energy losses in thin metal films. The atomic transitions corresponding to the measured energy losses are in many cases fairly easily established. However, there remain some which are questionable due to the fact that there is more than one feasible transition with energy differences of the order of the given energy loss. It is established that the principal interaction results in the excitation from the ground state of the neutral atom to the first excited level—the resonance excitation. It is also found that dipole excitations predominate

Lewis B. Leder

1957-09-15T23:59:59.000Z

297

Field emission properties of chemical vapor deposited individual graphene  

SciTech Connect

Here, we report field emission (FE) properties of a chemical vapor deposited individual graphene investigated by in-situ transmission electron microscopy. Free-standing bilayer graphene is mounted on a cathode microprobe and FE processes are investigated varying the vacuum gap of cathode and anode. The threshold field for 10?nA current were found to be 515, 610, and 870?V/?m for vacuum gap of 400, 300, and 200?nm, respectively. It is observed that the structural stability of a high quality bilayer graphene is considerably stable during emission process. By contacting the nanoprobe with graphene and applying a bias voltage, structural deformation and buckling are observed with significant rise in temperature owing to Joule heating effect. The finding can be significant for practical application of graphene related materials in emitter based devices as well as understanding the contact resistance influence and heating effect.

Zamri Yusop, Mohd [Department of Frontier Materials, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, 466-8555 Nagoya (Japan); Department of Materials, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor (Malaysia); Kalita, Golap, E-mail: kalita.golap@nitech.ac.jp [Department of Frontier Materials, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, 466-8555 Nagoya (Japan); Center for Fostering Young and Innovative Researchers, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, 466-8555 Nagoya (Japan); Yaakob, Yazid; Takahashi, Chisato; Tanemura, Masaki [Department of Frontier Materials, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, 466-8555 Nagoya (Japan)

2014-03-03T23:59:59.000Z

298

EA-0881: Tank 241-c-103 Organic Vapor and Liquid Characterization and  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

81: Tank 241-c-103 Organic Vapor and Liquid Characterization 81: Tank 241-c-103 Organic Vapor and Liquid Characterization and Supporting Activities, Hanford Site, Richland, Washington EA-0881: Tank 241-c-103 Organic Vapor and Liquid Characterization and Supporting Activities, Hanford Site, Richland, Washington SUMMARY This EA evaluates the environmental impacts of a proposal to sample the vapor space and liquid waste and perform other supporting activities in Tank 241-C-103 located in the 241-C Tank Farm on the Hanford Site in Richland, Washington. PUBLIC COMMENT OPPORTUNITIES None available at this time. DOCUMENTS AVAILABLE FOR DOWNLOAD August 10, 1992 EA-0881: Finding of No Significant Impact Tank 241-c-103 Organic Vapor and Liquid Characterization and Supporting Activities, Hanford Site, Richland, Washington August 10, 1992

299

Building America Top Innovations Hall of Fame Profile Â… Vapor Retarder Classification  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2006 the IRC has permitted Class III 2006 the IRC has permitted Class III vapor retarders like latex paint (see list above) in all climate zones under certain conditions thanks to research by Building America teams. Air-tight and well-insulated homes have little or no tolerance for drying if they get wet; moisture control is critical. That's why Building America research establishing vapor retarder classifications and their appropriate applications has been instrumental in the market transformation to high-performance homes. As buildings have gotten tighter over the past several decades, questions about vapor retarders and vapor barriers have confounded builders and code developers. Vapor barriers have traditionally been installed on the warm in winter side of the wall assembly in an attempt to keep interior moisture from entering the wall cavity

300

WATER VAPOR IN THE PROTOPLANETARY DISK OF DG Tau  

SciTech Connect

Water is key in the evolution of protoplanetary disks and the formation of comets and icy/water planets. While high-excitation water lines originating in the hot inner disk have been detected in several T Tauri stars (TTSs), water vapor from the outer disk, where most water ice reservoirs are stored, was only reported in the nearby TTS TW Hya. We present spectrally resolved Herschel/HIFI observations of the young TTS DG Tau in the ortho- and para-water ground-state transitions at 557 and 1113 GHz. The lines show a narrow double-peaked profile, consistent with an origin in the outer disk, and are {approx}19-26 times brighter than in TW Hya. In contrast, CO and [C II] lines are dominated by emission from the envelope/outflow, which makes H{sub 2}O lines a unique tracer of the disk of DG Tau. Disk modeling with the thermo-chemical code ProDiMo indicates that the strong UV field, due to the young age and strong accretion of DG Tau, irradiates a disk upper layer at 10-90 AU from the star, heating it up to temperatures of 600 K and producing the observed bright water lines. The models suggest a disk mass of 0.015-0.1 M{sub Sun }, consistent with the estimated minimum mass of the solar nebula before planet formation, and a water reservoir of {approx}10{sup 2}-10{sup 3} Earth oceans in vapor and {approx}100 times larger in the form of ice. Hence, this detection supports the scenario of ocean delivery on terrestrial planets by the impact of icy bodies forming in the outer disk.

Podio, L.; Dougados, C.; Thi, W.-F.; Menard, F.; Pinte, C. [UJF-Grenoble 1/CNRS-INSU, Institut de Planetologie et d'Astrophysique de Grenoble (IPAG) UMR 5274, F-38041 Grenoble (France); Kamp, I.; Meijerink, R.; Spaans, M.; Aresu, G. [Kapteyn Astronomical Institute, University of Groningen, Landleven 12, 9747 AD Groningen (Netherlands); Codella, C. [INAF-Osservatorio Astrofisico di Arcetri, Largo E. Fermi 5, I-50125 Florence (Italy); Cabrit, S. [LERMA, UMR 8112 du CNRS, Observatoire de Paris, Ecole Normale Superieure, Universite Pierre et Marie Curie, Universite de Cergy-Pontoise, 61 Av. de l'Observatoire, F-75014 Paris (France); Nisini, B. [INAF-Osservatorio Astronomico di Roma, via di Frascati 33, I-00040 Monte Porzio Catone (Italy); Sandell, G. [SOFIA-USRA, NASA Ames Research Center, MS 232-12, Building N232, Rm. 146, P.O. Box 1, Moffett Field, CA 94035-0001 (United States); Williams, J. P. [Institute for Astronomy (IfA), University of Hawaii, 2680 Woodlawn Dr., Honolulu, HI 96822 (United States); Testi, L. [European Southern Observatory, Karl-Schwarzschild-Strasse 2, D-85748 Garching (Germany); Woitke, P. [SUPA, School of Physics and Astronomy, University of St. Andrews, KY16 9SS (United Kingdom)

2013-03-20T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Ash vaporization in circulating fluidized bed coal combustion  

SciTech Connect

In this work, the vaporization of the ash-forming constituents in circulating fluidized bed combustion (CFBC) in a full-scale 80 MW{sub th} unit was studied. Ash vaporization in CFBC was studied by measuring the fly ash aerosols in a full-scale boiler upstream of the electrostatic precipitator (ESP) at the flue gas temperature of 125{degree}C. The fly ash number size distributions showed two distinct modes in the submicrometer size range, at particle diameters 0.02 and 0.3 {mu}m. The concentration of the ultrafine 0.02-{mu}m mode showed a large variation with time and it decreased as the measurements advanced. The concentration of the 0.02-{mu}m mode was two orders of magnitude lower than in the submicrometer mode observed earlier in the bubbling FBC and up to three orders of magnitude lower than in the pulverized coal combustion. Scanning electron micrographs showed few ultrafine particles. The intermediate mode at 0.3 {mu}m consisted of particles irregular in shape, and hence in this mode the particles had not been formed via a gas to particle route. We propose that the 0.3-{mu}m mode had been formed from the partial melting of the very fine mineral particles in the coal. The mass size distribution in the size range 0.01-70 {mu}m was unimodal with maximum at 20 {mu}m. Less than 1% of the fly ash particles was found in the submicrometer size range. 35 refs., 8 figs., 3 tabs.

Lind, T.; Kauppinen, E.I.; Maenhaut, W. [Univ. of Gent (Belgium); Shah, A.; Huggins, F. [Univ. of Kentucky, Lexington, KY (United States)

1996-04-01T23:59:59.000Z

302

Analysis of crude oil vapor pressures at the U.S. Strategic Petroleum Reserve.  

SciTech Connect

Crude oil storage caverns at the U.S. Strategic Petroleum Reserve (SPR) are solution-mined from subsurface salt domes along the U.S. Gulf Coast. While these salt domes exhibit many attractive characteristics for large-volume, long-term storage of oil such as low cost for construction, low permeability for effective fluids containment, and secure location deep underground, they also present unique technical challenges for maintaining oil quality within delivery standards. The vapor pressures of the crude oils stored at SPR tend to increase with storage time due to the combined effects of geothermal heating and gas intrusion from the surrounding salt. This presents a problem for oil delivery offsite because high vapor-pressure oil may lead to excessive atmospheric emissions of hydrocarbon gases that present explosion hazards, health hazards, and handling problems at atmospheric pressure. Recognizing this potential hazard, the U.S. Department of Energy, owner and operator of the SPR, implemented a crude oil vapor pressure monitoring program that collects vapor pressure data for all the storage caverns. From these data, DOE evaluates the rate of change in vapor pressures of its oils in the SPR. Moreover, DOE implemented a vapor pressure mitigation program in which the oils are degassed periodically and will be cooled immediately prior to delivery in order to reduce the vapor pressure to safe handling levels. The work described in this report evaluates the entire database since its origin in 1993, and determines the current levels of vapor pressure around the SPR, as well as the rate of change for purposes of optimizing both the mitigation program and meeting safe delivery standards. Generally, the rate of vapor pressure increase appears to be lower in this analysis than reported in the past and, problematic gas intrusion seems to be limited to just a few caverns. This being said, much of the current SPR inventory exceeds vapor pressure delivery guidelines and must be degassed and cooled in order to meet current delivery standards.

Rudeen, David Keith (GRAM, Inc., Albuquerque, NM); Lord, David L.

2005-08-01T23:59:59.000Z

303

Vaporization modeling of petroleum-biofuel drops using a hybrid multi-component approach  

SciTech Connect

Numerical modeling of the vaporization characteristics of multi-component fuel mixtures is performed in this study. The fuel mixtures studied include those of binary components, biodiesel, diesel-biodiesel, and gasoline-ethanol. The use of biofuels has become increasingly important for reasons of environmental sustainability. Biofuels are often blended with petroleum fuels, and the detailed understanding of the vaporization process is essential to designing a clean and efficient combustion system. In this study, a hybrid vaporization model is developed that uses continuous thermodynamics to describe petroleum fuels and discrete components to represent biofuels. The model is validated using the experimental data of n-heptane, n-heptane-n-decane mixture, and biodiesel. Since biodiesel properties are not universal due to the variation in feedstock, methods for predicting biodiesel properties based on the five dominant fatty acid components are introduced. Good levels of agreement in the predicted and measured drop size histories are obtained. Furthermore, in modeling the diesel-biodiesel drop, results show that the drop lifetime increases with the biodiesel concentration in the blend. During vaporization, only the lighter components of diesel fuel vaporize at the beginning. Biodiesel components do not vaporize until some time during the vaporization process. On the other hand, results of gasoline-ethanol drops indicate that both fuels start to vaporize once the process begins. At the beginning, the lighter components of gasoline have a slightly higher vaporization rate than ethanol. After a certain time, ethanol vaporizes faster than the remaining gasoline components. At the end, the drop reduces to a regular gasoline drop with heavier components. Overall, the drop lifetime increases as the concentration of ethanol increases in the drop due to the higher latent heat. (author)

Zhang, Lei; Kong, Song-Charng [Department of Mechanical Engineering, Iowa State University, 2025 Black Engineering Building, Ames, IA 50011 (United States)

2010-11-15T23:59:59.000Z

304

Building America Technology Solutions for New and Existing Homes: Moisture Durability of Vapor Permeable Insulating Sheathing (Fact Sheet)  

Energy.gov (U.S. Department of Energy (DOE))

In this project, Building America team Building Science Corporation researched some of the ramifications of using exterior, vapor permeable insulation on retrofit walls with vapor permeable cavity insulation. Retrofit strategies are a key factor in reducing exterior building stock consumption.

305

Improving Energy Efficiency and Cost-Effectiveness of Batch Distillation for Separating Wide Boiling Constituents. 1. Vapor Recompression Column  

Science Journals Connector (OSTI)

Although the direct vapor recompression column (VRC) has been known for its application in continuous distillation since the 1960s, the research on vapor recompressed batch distillation (VRBD) started a couple of years ago. In this contribution, a batch ...

Md. Malik Nawaz Khan; G. Uday Bhaskar Babu; Amiya K. Jana

2012-11-05T23:59:59.000Z

306

Tank 241-BY-104 vapor sampling and analysis tank characterization report. Revision 1  

SciTech Connect

Tank 241-BY-104 headspace gas and vapor samples were collected and analyzed to help determine the potential risks to tank farm workers due to fugitive emissions from the tank. The drivers and objectives of waste tank headspace sampling and analysis are discussed in {open_quotes}Program Plan for the Resolution of Tank Vapor Issues.{close_quotes} Tank 241-BY-104 was vapor sampled in accordance with {open_quotes}Data Quality Objectives for Generic In-Tank Health and Safety Issue Resolution.{close_quotes}

Huckaby, J.L.

1995-05-31T23:59:59.000Z

307

Desorption efficiencies of toluene and n-butanol in an organic vapor monitor  

E-Print Network (OSTI)

&jards has become one of the most important industrial hygiene f unct i one e The levei of exposure to many organic vapor;=, is det r- mined by co' lecting the chemical on some type o solid sor- bent. Of the various adsorbents available {silica gel... two of these paramet rs) ~ The objective of this re, . earch wa, . to investigate the effe ts of chemical phase (liquid or vapor) on the desorp- tion efficiencies of toluene and n-buta?ol adsorbed on acti- vated charcoal in organic vapor monitors...

Heaney, Mary Ann

2012-06-07T23:59:59.000Z

308

Tank 241-BY-103 vapor sampling and analysis tank characterization report  

SciTech Connect

Tank 241-BY-103 headspace gas and vapor samples were collected and analyzed to help determine the potential risks to tank farm workers due to fugitive emissions from the tank. The drivers and objectives of waste tank headspace sampling and analysis are discussed in {open_quotes}Program Plan for the Resolution of Tank Vapor Issues.{close_quotes} Tank 241-BY-103 was vapor sampled in accordance with {open_quotes}Data Quality Objectives for Generic In-Tank Health and Safety Issue Resolution.{close_quotes}

Huckaby, J.L.

1995-05-05T23:59:59.000Z

309

Tank 241-BY-108 vapor sampling and analysis tank characterization report. Revision 1  

SciTech Connect

Tank 241-BY-108 headspace gas and vapor samples were collected and analyzed to help determine the potential risks to tank farm workers due to fugitive emissions from the tank. The drivers and objectives of waste tank headspace sampling and analysis are discussed in ``Program Plan for the Resolution of Tank Vapor Issues`` (Osborne and Huckaby 1994). Tank 241-BY-108 was vapor sampled in accordance with ``Data Quality Objectives for Generic In-Tank Health and Safety Issue Resolution (Osborne et al., 1994).

Huckaby, J.L.

1995-05-31T23:59:59.000Z

310

Tank 241-BY-105 vapor sampling and analysis tank characterization report. Revision 1  

SciTech Connect

Tank 241-BY-105 headspace gas and vapor samples were collected and analyzed to help determine the potential risks to tank farm workers due to fugitive emissions from the tank. The drivers and objectives of waste tank headspace sampling and analysis are discussed in {open_quotes}Program Plan for the Resolution of Tank Vapor Issues.{close_quotes} Tank 241-BY-105 was vapor sampled in accordance with {open_quotes}Data Quality Objectives for Generic In-Tank Health and Safety Issue Resolution.{close_quotes}

Huckaby, J.L.

1995-05-31T23:59:59.000Z

311

Tank 241-BY-107 vapor sampling and analysis tank characterization report. Revision 1  

SciTech Connect

Tank 241-BY-107 headspace gas and vapor samples were collected and analyzed to help determine the potential risks to tank farm workers due to fugitive emissions from the tank. The drivers and objectives of waste tank headspace sampling and analysis are discussed in {open_quotes}Program Plan for the Resolution of Tank Vapor Issues.{close_quotes} Tank 241-BY-107 was vapor sampled in accordance with {open_quotes}Data Quality Objectives for Generic In-Tank Health and Safety Issue Resolution.{close_quotes}

Huckaby, J.L.

1995-05-31T23:59:59.000Z

312

Tank 241-BY-107 vapor sampling and analysis tank characterization report  

SciTech Connect

Tank 241-BY-107 headspace gas and vapor samples were collected and analyzed to help determine the potential risks to tank farm workers due to fugitive emissions from the tank. The drivers and objectives of waste tank headspace sampling and analysis are discussed in {open_quotes}Program Plan for the Resolution of Tank Vapor Issues{close_quotes}. Tank 241-BY-107 was vapor sampled in accordance with {open_quotes}Data Quality Objectives for Generic In-Tank Health and Safety Issue Resolution{close_quotes}.

Huckaby, J.L.

1995-05-05T23:59:59.000Z

313

Tank 241-BY-106 vapor sampling and analysis tank characterization report. Revision 1  

SciTech Connect

Tank 241-BY-106 headspace gas and vapor samples were collected and analyzed to help determine the potential risks to tank farm workers due to fugitive emissions from the tank. The drivers and objectives of waste tank headspace sampling and analysis are discussed in {open_quotes}Program Plan for the Resolution of Tank Vapor Issues.{close_quotes} Tank 241-BY-106 was vapor sampled in accordance with {open_quotes}Data Quality Objectives for Generic In-Tank Health and Safety Issue Resolution.{close_quotes}

Huckaby, J.L.

1995-05-31T23:59:59.000Z

314

Ion-beam-induced epitaxial vapor-phase growth: A molecular-dynamics study  

Science Journals Connector (OSTI)

Low-energy ions which bombard a vapor-deposited film of low adatom mobility during growth mobilize surface atoms in the vicinity of the ion impact, causing a modification in the evolving microstructure. In a two-dimensional molecular-dynamics simulation where inert-gas ions strike a growing film of Lennard-Jones particles, it is demonstrated that ion bombardment during growth causes the filling of voids quenched in during vapor condensation and induces homoepitaxial growth. The dependence of film density and degree of homoepitaxial growth on the ion-to-vapor arrival rate ratio and ion energy is studied in detail.

Karl-Heinz Müller

1987-05-15T23:59:59.000Z

315

Production of higher quality bio-oils by in-line esterification of pyrolysis vapor  

DOE Patents (OSTI)

The disclosure encompasses in-line reactive condensation processes via vapor phase esterification of bio-oil to decease reactive species concentration and water content in the oily phase of a two-phase oil, thereby increasing storage stability and heating value. Esterification of the bio-oil vapor occurs via the vapor phase contact and subsequent reaction of organic acids with ethanol during condensation results in the production of water and esters. The pyrolysis oil product can have an increased ester content and an increased stability when compared to a condensed pyrolysis oil product not treated with an atomized alcohol.

Hilten, Roger Norris; Das, Keshav; Kastner, James R; Bibens, Brian P

2014-12-02T23:59:59.000Z

316

Chemical vapor deposition of amorphous silicon films from disilane  

SciTech Connect

Amorphous silicon films for fabrication of solar cells have been deposited by thermal chemical vapor deposition (CVD) from disilane (Si/sub 2/H/sub 6/) using a tubular flow reactor. A mathematical description for the CVD reactor was developed and solved by a numerical procedure. The proposed chemical reaction network for the model is based on silylene (SiH/sub 2/) insertion in the gas phase and film growth from SiH/sub 2/ and silicon polymers (Si/sub n/N/sub 2n/, n approx. 10). Estimates of the rate constants have been obtained for trisilane decomposition, silicon polymer formation, and polymer dehydrogenation. The silane unimolecular decomposition rate constants were corrected for pressure effects. The model behavior is compared to the experimental results over the range of conditions: reactor temperature (360 to 485/sup 0/C), pressures (2 to 48 torr), and gas holding time (1 to 70 s). Within the above range of conditions, film growth rate varies from 0.01 to 30 A/s. Results indicate that silicon polymers are the main film precursors for gas holding times greater than 3 s. Film growth by silylene only becomes important at short holding times, large inert gas dilution, and positions near the beginning of the reactor hot zone.

Bogaert, R.J.

1986-01-01T23:59:59.000Z

317

Soil Vapor Extraction System Optimization, Transition, and Closure Guidance  

SciTech Connect

Soil vapor extraction (SVE) is a prevalent remediation approach for volatile contaminants in the vadose zone. A diminishing rate of contaminant extraction over time is typically observed due to 1) diminishing contaminant mass, and/or 2) slow rates of removal for contamination in low-permeability zones. After a SVE system begins to show indications of diminishing contaminant removal rate, SVE performance needs to be evaluated to determine whether the system should be optimized, terminated, or transitioned to another technology to replace or augment SVE. This guidance specifically addresses the elements of this type of performance assessment. While not specifically presented, the approach and analyses in this guidance could also be applied at the onset of remediation selection for a site as a way to evaluate current or future impacts to groundwater from vadose zone contamination. The guidance presented here builds from existing guidance for SVE design, operation, optimization, and closure from the U.S. Environmental Protection Agency, U.S. Army Corps of Engineers, and the Air Force Center for Engineering and the Environment. The purpose of the material herein is to clarify and focus on the specific actions and decisions related to SVE optimization, transition, and/or closure.

Truex, Michael J.; Becker, Dave; Simon, Michelle A.; Oostrom, Martinus; Rice, Amy K.; Johnson, Christian D.

2013-02-08T23:59:59.000Z

318

Growth of graphene underlayers by chemical vapor deposition  

SciTech Connect

We present a simple and very convincing approach to visualizing that subsequent layers of graphene grow between the existing monolayer graphene and the copper catalyst in chemical vapor deposition (CVD). Graphene samples were grown by CVD and then transferred onto glass substrates by the bubbling method in two ways, either direct-transfer (DT) to yield poly (methyl methacrylate) (PMMA)/graphene/glass or (2) inverted transfer (IT) to yield graphene/PMMA/glass. Field emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM) were used to reveal surface features for both the DT and IT samples. The results from FE-SEM and AFM topographic analyses of the surfaces revealed the underlayer growth of subsequent layers. The subsequent layers in the IT samples are visualized as 3D structures, where the smaller graphene layers lie above the larger layers stacked in a concentric manner. The results support the formation of the so-called “inverted wedding cake” stacking in multilayer graphene growth.

Fabiane, Mopeli; Khamlich, Saleh; Bello, Abdulhakeem; Dangbegnon, Julien; Momodu, Damilola; Manyala, Ncholu, E-mail: ncholu.manyala@up.ac.za [Department of Physics, Institute of Applied Materials, SARChI Chair in Carbon Technology and Materials, University of Pretoria, Pretoria 0028 (South Africa)] [Department of Physics, Institute of Applied Materials, SARChI Chair in Carbon Technology and Materials, University of Pretoria, Pretoria 0028 (South Africa); Charlie Johnson, A. T. [Department of Physics and Astronomy, University of Pennsylvania, Philadelphia, Pennsylvania 19104 (United States)] [Department of Physics and Astronomy, University of Pennsylvania, Philadelphia, Pennsylvania 19104 (United States)

2013-11-15T23:59:59.000Z

319

Charged impurity-induced scatterings in chemical vapor deposited graphene  

SciTech Connect

We investigate the effects of defect scatterings on the electric transport properties of chemical vapor deposited (CVD) graphene by measuring the carrier density dependence of the magneto-conductivity. To clarify the dominant scattering mechanism, we perform extensive measurements on large-area samples with different mobility to exclude the edge effect. We analyze our data with the major scattering mechanisms such as short-range static scatters, short-range screened Coulomb disorders, and weak-localization (WL). We establish that the charged impurities are the predominant scatters because there is a strong correlation between the mobility and the charge impurity density. Near the charge neutral point (CNP), the electron-hole puddles that are induced by the charged impurities enhance the inter-valley scattering, which is favorable for WL observations. Away from the CNP, the charged-impurity-induced scattering is weak because of the effective screening by the charge carriers. As a result, the local static structural defects govern the charge transport. Our findings provide compelling evidence for understanding the scattering mechanisms in graphene and pave the way for the improvement of fabrication techniques to achieve high-quality CVD graphene.

Li, Ming-Yang; Tang, Chiu-Chun [Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Ling, D. C. [Department of Physics, Tamkang University, Tamsui Dist., New Taipei 25137, Taiwan (China); Li, L. J. [Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Institute of Atomic and Molecular Sciences, Academia Sinica, Taipei 11529, Taiwan (China); Chi, C. C.; Chen, Jeng-Chung [Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Frontier Research Center on Fundamental and Applied Sciences of Matters, National Tsing Hua University, Hsinchu 30013, Taiwan (China)

2013-12-21T23:59:59.000Z

320

Plasma and Ion Assistance in Physical Vapor Deposition: AHistorical Perspective  

SciTech Connect

Deposition of films using plasma or plasma-assist can betraced back surprisingly far, namely to the 18th century for arcs and tothe 19th century for sputtering. However, only since the 1960s thecoatings community considered other processes than evaporation for largescale commercial use. Ion Plating was perhaps the first importantprocess, introducing vapor ionization and substrate bias to generate abeam of ions arriving on the surface of the growing film. Ratherindependently, cathodic arc deposition was established as an energeticcondensation process, first in the former Soviet Union in the 1970s, andin the 1980s in the Western Hemisphere. About a dozen various ion-basedcoating technologies evolved in the last decades, all characterized byspecific plasma or ion generation processes. Gridded and gridless ionsources were taken from space propulsion and applied to thin filmdeposition. Modeling and simulation have helped to make plasma and ionseffects to be reasonably well understood. Yet--due to the complex, oftennon-linear and non-equilibrium nature of plasma and surfaceinteractions--there is still a place for the experience plasma"sourcerer."

Anders, Andre

2007-02-28T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Effects of inhaled 1-bromopropane vapor on rat metabolism  

Science Journals Connector (OSTI)

Wistar male rats were exposed to 1-bromopromane (1-BP) vapor for 6 h a day, 5 days a week, for 3 and 4 weeks (1500 ppm) and 1 day, and 4 and 12 weeks (700 ppm). After the exposures, 1-BP and its metabolites were measured temporally. In the samples obtained from the 700 ppm exposures, hematological and biochemical examinations in blood and measurements of hepatic cytochromes P450 were carried out. 1-BP in blood decreased rapidly to the detection limit within 0.7 h. On the other hand, bromine ion persisted longer in both blood and urine; the biological half-life of bromine ion was 4.7–15.0 days in blood and 5.0–7.5 days in urine. Glycidol was detected in the urine samples. Based on the experimental results, the metabolic pathway of 1-BP was discussed. Hepatic cytochromes P450, aspartate aminotransferase (AST) and alanine aminotransferase (ALT) in blood decreased significantly with 1-BP exposure, but other enzyme activities did not differ significantly.

Toru Ishidao; Naoki Kunugita; Yukiko Fueta; Keiichi Arashidani; Hajime Hori

2002-01-01T23:59:59.000Z

322

Treating process wastewater employing vacuum distillation using mechanical vapor recompression  

SciTech Connect

Process wastewater has been successfully treated using an enhanced variable vacuum distillation system (VVDS). The removal of contaminants is achieved initially by degassing the liquid under an intense vacuum which removes the volatile organic compounds. The resulting liquid is then distilled under a vacuum using mechanical vapor recompression. The system was invented by Derald McCabe. This innovative treatment system removes virtually all of the contaminants, such as TSS, TDS, BOD{sub 5}, COD, heavy metals and mineral compounds. The resultant aqueous portion normally returns to a neutral pH. Due to the unique system operation, scaling problems (often encountered in conventional distillation) have not been detected in this system. The VVDS is extremely energy efficiency because the heat for distillation is generated and recycled mechanically. Using electricity as the energy source, the approximate operating cost, based on $0.05 KWH, may vary from $0.005 to $0.01 per gallon depending on the size and capacity of the equipment. Based on applications in waste streams performed to-date, the VVDS process has yielded a distilled water stream and the concentrated solids have been used as a byproduct or as a concentrated non-dischargeable waste for disposal.

McCabe, D.L. [Brandt, Houston, TX (United States)] [Brandt, Houston, TX (United States); Vivona, M.A. [ICF Kaiser Engineers, Inc., Houston, TX (United States). Water and Wastewater Dept.] [ICF Kaiser Engineers, Inc., Houston, TX (United States). Water and Wastewater Dept.

1999-05-01T23:59:59.000Z

323

Water, Vapor, and Salt Dynamics in a Hot Repository  

SciTech Connect

The purpose of this paper is to report the results of a new model study examining the high temperature nuclear waste disposal concept at Yucca Mountain using MULTIFLUX, an integrated in-drift- and mountain-scale thermal-hydrologic model. The results show that a large amount of vapor flow into the drift is expected during the period of above-boiling temperatures. This phenomenon makes the emplacement drift a water/moisture attractor during the above-boiling temperature operation. The evaporation of the percolation water into the drift gives rise to salt accumulation in the rock wall, especially in the crown of the drift for about 1500 years in the example. The deposited salts over the drift footprint, almost entirely present in the fractures, may enter the drift either by rock fall or by water drippage. During the high temperature operation mode, the barometric pressure variation creates fluctuating relative humidity in the emplacement drift with a time period of approximately 10 days. Potentially wet and dry conditions and condensation on salt-laden drift wall sections may adversely affect the storage environment. Salt accumulations during the above-boiling temperature operation must be sufficiently addressed to fully understand the waste package environment during the thermal period. Until the questions are resolved, a below-boiling repository design is favored where the Alloy-22 will be less susceptible to localized corrosion. (authors)

Bahrami, Davood; Danko, George [Department of Mining Engineering, University of Nevada, Reno, 1664 N. Virginia St., Reno, NV, 89557 (United States); Walton, John [Department of Civil Engineering, University of Texas at El Paso, 500 W. University, El Paso, TX, 79968 (United States)

2007-07-01T23:59:59.000Z

324

Effect of dimensionality on vapor-liquid phase transition  

SciTech Connect

Dimensionality play significant role on ‘phase transitions’. Fluids in macroscopic confinement (bulk or 3-Dimensional, 3D) do not show significant changes in their phase transition properties with extent of confinement, since the number of molecules away from the surrounding surfaces is astronomically higher than the number of molecules in close proximity of the confining surfaces. In microscopic confinement (quasi 3D to quasi-2D), however, the number of molecules away from the close proximity of the surface is not as high as is the case with macroscopic (3D) confinement. Hence, under the same thermodynamic conditions ‘phase transition’ properties at microscopic confinement may not remain the same as the macroscopic or 3D values. Phase transitions at extremely small scale become very sensitive to the dimensions as well as the surface characteristics of the system. In this work our investigations reveal the effect of dimensionality on the phase transition from 3D to quasi-2D to 2D behavior. We have used grand canonical transition matrix Monte Carlo simulation to understand the vapor–liquid phase transitions from 3D to quasi-2D behavior. Such studies can be helpful in understanding and controlling the fluid film behaviour confined between solid surfaces of few molecular diameters, for example, in lubrication applications.

Singh, Sudhir Kumar, E-mail: sksingh@thapar.edu [Department Chemical Engineering, Thapar University, Patiala-147004 Punjab (India)

2014-04-24T23:59:59.000Z

325

Tank Vapor Characterization Project: Headspace vapor characterization of Hanford Waste Tank U-204, Results from samples collected on August 8, 1995  

SciTech Connect

This report describes the analytical results of vapor samples taken from the headspace of the waste storage tank 241-U-204 (Tank U-204) at the Hanford Site in Washington State. The results described in this report were obtained to characterize the vapors present in the tank headspace and to support safety evaluations and tank-farm operations. The results include air concentrations of selected inorganic and organic analytes and grouped compounds from samples obtained by Westinghouse Hanford Company (WHC) and provided for analysis to Pacific Northwest National Laboratory (PNL). Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNL. Analyte concentrations were based on analytical results and, where appropriate, sample volumes provided by WHC. A summary of the results is listed. Detailed descriptions of the analytical results appear in the text.

Clauss, T.W.; Evans, J.C.; McVeety, B.D.; Pool, K.H.; Thomas, B.L.; Olsen, K.B.; Fruchter, J.S.; Ligotke, M.W.

1995-11-01T23:59:59.000Z

326

Mercury Vapor At Lahaina-Kaanapali Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

Mercury Vapor At Lahaina-Kaanapali Area (Thomas, 1986) Mercury Vapor At Lahaina-Kaanapali Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Lahaina-Kaanapali Area (Thomas, 1986) Exploration Activity Details Location Lahaina-Kaanapali Area Exploration Technique Mercury Vapor Activity Date Usefulness not indicated DOE-funding Unknown Notes The soil mercury concentration and radon emanometry patterns observed for the Lahaina prospect were similar to those found in Olowalu. Several localized zones of high mercury concentration or enhanced radon emanation were observed, but showed little relationship to each other or to the recognized geologic structure in the area. The data were interpreted to suggest that there might be a small thermal anomaly to the northeast of the

327

GPS Water Vapor Projects Within the ARM Southern Great Plains Region  

NLE Websites -- All DOE Office Websites (Extended Search)

GPS Water Vapor Projects Within the ARM GPS Water Vapor Projects Within the ARM Southern Great Plains Region J. Braun, T. Van Hove, S. Y. Ha, and C. Rocken GPS Science and Technology Program University Corporation for Atmospheric Research Boulder, Colorado Abstract The U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Program has a need for an improved capability to measure and characterize the four-dimensional distribution of water vapor within the atmosphere. Applications for this type of data include their use in radiation transfer studies, cloud-resolving and single-column models, and for the establishment of an extended time series of water vapor observations. The University Corporation for Atmospheric Research's (UCAR) GPS Science and Technology (GST) Program is working with ARM to leverage the substantial investment in

328

Mercury Vapor At Hualalai Northwest Rift Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

Mercury Vapor At Hualalai Northwest Rift Area (Thomas, 1986) Mercury Vapor At Hualalai Northwest Rift Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Hualalai Northwest Rift Area (Thomas, 1986) Exploration Activity Details Location Hualalai Northwest Rift Area Exploration Technique Mercury Vapor Activity Date Usefulness not indicated DOE-funding Unknown Notes The Hualalai lower northwest rift and southern flank were sampled for soil mercury concentration and radon emanation rates (Cox and Cuff, 1981d). The data generated by these surveys yielded complex patterns of mercury concentrations and radon emanation rates that generally did not show coincident anomalies (Figs 42, 43). References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In

329

Glenwood Springs Vapor Caves Pool & Spa Low Temperature Geothermal Facility  

Open Energy Info (EERE)

Springs Vapor Caves Pool & Spa Low Temperature Geothermal Facility Springs Vapor Caves Pool & Spa Low Temperature Geothermal Facility Jump to: navigation, search Name Glenwood Springs Vapor Caves Pool & Spa Low Temperature Geothermal Facility Facility Glenwood Springs Vapor Caves Sector Geothermal energy Type Pool and Spa Location Glenwood Springs, Colorado Coordinates 39.5505376°, -107.3247762° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

330

Mercury Vapor At Valley Of Ten Thousand Smokes Region Area (Kodosky, 1989)  

Open Energy Info (EERE)

Mercury Vapor At Valley Of Ten Thousand Smokes Region Area (Kodosky, 1989) Mercury Vapor At Valley Of Ten Thousand Smokes Region Area (Kodosky, 1989) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Valley Of Ten Thousand Smokes Region Area (Kodosky, 1989) Exploration Activity Details Location Valley Of Ten Thousand Smokes Region Area Exploration Technique Mercury Vapor Activity Date Usefulness useful DOE-funding Unknown Notes One-hundred twelve samples were collected from relatively unaltered air-fall ejecta along two Novarupta Basin traverse lines (Fig. 5). One hundred eighty-two samples were taken from active/fossil fumaroles in Novarupta Basin (22 sites, Fig. 5), fossil fumaroles (41 sites) and air-fall tephra (2 sites) within and immediately adjacent to the remainder of the VTTS (Fig. 6). In total, 294 samples were collected from 127 sites

331

Fault detection methods for vapor-compression air conditioners using electrical measurements  

E-Print Network (OSTI)

(cont.) This method was experimentally tested and validated on a commercially available air handler and duct system. In the second class of faults studied, liquid refrigerant, rather than vapor, enters the cylinder of a ...

Laughman, Christopher Reed.

2008-01-01T23:59:59.000Z

332

Exergy analysis and experimental study of a vapor compression refrigeration cycle  

Science Journals Connector (OSTI)

This article presents a detailed experimental analysis of 2TR (ton of refrigeration) vapor compression refrigeration cycle for different percentage of refrigerant charge using exergy analysis. An experimental set...

S. Anand; S. K. Tyagi

2012-11-01T23:59:59.000Z

333

Phase Transition Enthalpy Measurements of Organic and Organometallic Compounds. Sublimation, Vaporization and Fusion Enthalpies From  

E-Print Network (OSTI)

Phase Transition Enthalpy Measurements of Organic and Organometallic Compounds. Sublimation, Vaporization and Fusion Enthalpies From 1880 to 2010 William Acree, Jr. Department of Chemistry, University of North Texas, Denton, Texas 76203 James S. Chickosa... Department of Chemistry and Biochemistry

Chickos, James S.

334

Initiated chemical vapor deposition of polymeric thin films : mechanism and applications  

E-Print Network (OSTI)

Initiated chemical vapor deposition (iCVD) is a novel technique for depositing polymeric thin films. It is able to deposit thin films of application-specific polymers in one step without using any solvents. Its uniqueness ...

Chan, Kelvin, Ph. D. Massachusetts Institute of Technology

2005-01-01T23:59:59.000Z

335

Radon Transect Studies in Vapor- and Liquid-Dominated Geothermal Reservoirs  

SciTech Connect

This communication describes the transect analysis conducted at the vapor-dominated reservoirs at The Geysers in California and the liquid-dominated reservoirs at Cerro Prieto in Baja, California.

Semprini, Lewis; Kruger, Paul

1980-12-16T23:59:59.000Z

336

Vapor-liquid critical and interfacial properties of square-well fluids in slit pores  

E-Print Network (OSTI)

Jayant K. Singh,1,a and Sang Kyu Kwak2 1 Department of Chemical Engineering, Indian Institute and the shift of the vapor-liquid critical point. Nevertheless, in recent years, with the discovery of well

Singh, Jayant K.

337

Oxidative chemical vapor deposition of conductive polymers for use in novel photovoltaic device architectures  

E-Print Network (OSTI)

The conductive polymer poly(3,4-ethylenedioxythiophene), (PEDOT), deposited via oxidative chemical vapor deposition (oCVD) has been investigated for use in organic electronic devices. The oCVD process as well as the ...

Howden, Rachel M. (Rachel Mary)

2013-01-01T23:59:59.000Z

338

Iron (III) Chloride doping of large-area chemical vapor deposition graphene  

E-Print Network (OSTI)

Chemical doping is an effective method of reducing the sheet resistance of graphene. This thesis aims to develop an effective method of doping large area Chemical Vapor Deposition (CVD) graphene using Iron (III) Chloride ...

Song, Yi, S.M. Massachusetts Institute of Technology

2013-01-01T23:59:59.000Z

339

The kinetics of heterogeneous nucleation in vapor-liquid phase transitions in the presence of ions  

Science Journals Connector (OSTI)

A method for calculating the work of nucleus formation in vapor-liquid phase transitions in the presence of ions was suggested. The method took into account ions localized in the boundary surface layer of...

G. V. Anikin; L. S. Podenko

2008-12-01T23:59:59.000Z

340

CO-CATALYTIC ABSORPTION LAYERS FOR CONTROLLED LASER-INDUCED CHEMICAL VAPOR DEPOSITION OF CARBON NANOTUBES  

E-Print Network (OSTI)

The concept of co-catalytic layer structures for controlled laser-induced chemical vapor deposition of carbon nanotubes is established, in which a thin Ta support layer chemically aids the initial Fe catalyst reduction. This enables a significant...

Michaelis, F.B.; Weatherup, R.S.; Bayer, B.C.; Bock, M.C.D; Sugime, H.; Caneva, S.; Robertson, J.; Baumberg, J.J.; Hofmann, S.

2014-02-24T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Single- and few-layer graphene by ambient pressure chemical vapor deposition on nickel  

E-Print Network (OSTI)

An ambient pressure chemical vapor deposition (APCVD) process is used to fabricate graphene based films consisting of one to several graphene layers across their area. Polycrystalline Ni thin films are used and the graphene ...

Reina Ceeco, Alfonso

2010-01-01T23:59:59.000Z

342

Tropospheric Water Vapor Profiles Retrieved from Pressure-Broadened Emission Spectra at 22 GHz  

Science Journals Connector (OSTI)

The authors present the analysis and the evaluation of the retrieval of tropospheric water vapor profiles from pressure-broadened emission spectra at 22 GHz measured with a ground-based microwave spectroradiometer. The spectra have a bandwidth of ...

Alexander Haefele; Niklaus Kämpfer

2010-01-01T23:59:59.000Z

343

Plasma Enhanced Chemical Vapor Deposition on Living Substrates: Development, Characterization, and Biological Applications  

E-Print Network (OSTI)

This dissertation proposed the idea of “plasma-enhanced chemical vapor deposition on living substrates (PECVD on living substrates)” to bridge the gap between the thin film deposition technology and the biological and living substrates. This study...

Tsai, Tsung-Chan 1982-

2012-12-05T23:59:59.000Z

344

Understanding the Nanotube Growth Mechanism: A Strategy to Control Nanotube Chirality during Chemical Vapor Deposition Synthesis  

E-Print Network (OSTI)

during chemical vapor deposition synthesis must focus on controlling the structure of the nucleated nanotube seeds. DFT and RMD simulations demonstrate the viability of using the structures of catalyst particles over which nanotube growth proceeds...

Gomez Gualdron, Diego Armando 1983-

2012-10-26T23:59:59.000Z

345

E-Print Network 3.0 - acid vapor pressures Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

Sciences and Ecology 22 3b. Thermodynamics of moist air Water phase, water latent heat of vaporization Lv Summary: 3b. Thermodynamics of moist air Water phase, water latent...

346

E-Print Network 3.0 - alkali-metal vapor density Sample Search...  

NLE Websites -- All DOE Office Websites (Extended Search)

Physics 65 nature physics | VOL 3 | APRIL 2007 | www.nature.comnaturephysics 227 REVIEW ARTICLE Summary: in a high-density alkali-metal vapor in low magnetic fields. Phys....

347

Structure/processing relationships in vapor-liquid-solid nanowire epitaxy  

E-Print Network (OSTI)

The synthesis of Si and III-V nanowires using the vapor-liquid-solid (VLS) growth mechanism and low-cost Si substrates was investigated. The VLS mechanism allows fabrication of heterostructures which are not readily ...

Boles, Steven Tyler

2010-01-01T23:59:59.000Z

348

Desalination-of water by vapor-phase transport through hydrophobic nanopores  

E-Print Network (OSTI)

We propose a new approach to desalination of water whereby a pressure difference across a vapor-trapping nanopore induces selective transport of water by isothermal evaporation and condensation across the pore. Transport ...

Lee, Jongho

349

Inexpensive Near-IR Sun Photometer for Measuring Total Column Water Vapor  

Science Journals Connector (OSTI)

An inexpensive two-channel near-IR sun photometer for measuring total atmospheric column water vapor (precipitable water) has been developed for use by the Global Learning and Observations to Benefit the Environment (GLOBE) environmental science ...

David R. Brooks; Forrest M. Mims III; Richard Roettger

2007-07-01T23:59:59.000Z

350

Temperature and water vapor pressure effects on the friction coefficient of hydrogenated diamondlike carbon films.  

SciTech Connect

Microtribological measurements of a hydrogenated diamondlike carbon film in controlled gaseous environments show that water vapor plays a significant role in the friction coefficient. These experiments reveal an initial high friction transient behavior that does not reoccur even after extended periods of exposure to low partial pressures of H{sub 2}O and O{sub 2}. Experiments varying both water vapor pressure and sample temperature show trends of a decreasing friction coefficient as a function of both the decreasing water vapor pressure and the increasing substrate temperature. Theses trends are examined with regard to first order gas-surface interactions. Model fits give activation energies on the order of 40 kJ/mol, which is consistent with water vapor desorption.

Dickrell, P. L.; Sawyer, W. G.; Eryilmaz, O. L.; Erdemir, A.; Energy Technology; Univ. of Florida

2009-07-01T23:59:59.000Z

351

Bilayer graphene growth by low pressure chemical vapor deposition on copper foil  

E-Print Network (OSTI)

Successfully integrating graphene in standard processes for applications in electronics relies on the synthesis of high-quality films. In this work we study Low Pressure Chemical Vapor Deposition (LPCVD) growth of bilayer ...

Fang, Wenjing, S.M. Massachusetts Institute of Technology

2012-01-01T23:59:59.000Z

352

The design, fabrication, and implications of a solvothermal vapor annealing chamber  

E-Print Network (OSTI)

This thesis documents the design, fabrication, use, and benefits of a prototype aluminum solvothermal vapor annealing chamber which facilitates the self-assembly of block copolymers (BCPs) on silicon wafers which are then ...

Porter, Nathaniel R., Jr

2013-01-01T23:59:59.000Z

353

Optimization of multi-pressure himidification-dehumidification desalination using thermal vapor compression and hybridization  

E-Print Network (OSTI)

Humidification-dehumidification (HD or HDH) desalination, and specifically HD driven by a thermal vapor compressor (TVC), is a thermal desalination method that has the potential to produce potable water efficiently in order ...

Mistry, Karan Hemant

354

Assessment of soot particle vaporization effects during laser-induced incandescence with  

E-Print Network (OSTI)

Assessment of soot particle vaporization effects during laser-induced incandescence with time-induced incandescence (LII) has been successfully used for soot volume fraction and particle size measurements

Hahn, David W.

355

Liquefied Natural Gas (LNG) Vapor Dispersion Modeling with Computational Fluid Dynamics Codes  

E-Print Network (OSTI)

Federal regulation 49 CFR 193 and standard NFPA 59A require the use of validated consequence models to determine the vapor cloud dispersion exclusion zones for accidental liquefied natural gas (LNG) releases. For modeling purposes, the physical...

Qi, Ruifeng

2012-10-19T23:59:59.000Z

356

Atmospheric pressure chemical vapor deposition of TiN from tetrakis(dimethylamido)titanium and ammonia  

E-Print Network (OSTI)

pressure chemical vapor deposition. Experiments were conducted in a belt furnace; static experiments, in particular, is used for tool coating, solar-control films, and micro- electronic applications. Optically

357

Stable-Isotope Studies Of Rocks And Secondary Minerals In A Vapor-Dominated  

Open Energy Info (EERE)

Stable-Isotope Studies Of Rocks And Secondary Minerals In A Vapor-Dominated Stable-Isotope Studies Of Rocks And Secondary Minerals In A Vapor-Dominated Hydrothermal System At The Geysers, Sonoma County, California Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Stable-Isotope Studies Of Rocks And Secondary Minerals In A Vapor-Dominated Hydrothermal System At The Geysers, Sonoma County, California Details Activities (5) Areas (1) Regions (0) Abstract: The Geysers, a vapor-dominated hydrothermal system, is developed in host rock of the Franciscan Formation, which contains veins of quartz and calcite whose Δ18O values record the temperatures and isotopic compositions of fluids prevailing during at least two different episodes of rock-fluid interaction. The first episode took place at about 200°C, during which marine silica and carbonate apparently interacted with ocean

358

Magnetohydrodynamic Vapor Explosions: A Study with Potential Interest to the Safety of Fusion Reactor Project  

Science Journals Connector (OSTI)

In this paper, the possibility of vapor explosions in superheat liquids in presence of a magnetic field that undergo sudden variation of magnetic field is discussed. This possible phenomenon may play a very impor...

F. J. Arias

2010-04-01T23:59:59.000Z

359

Fluid Inclusion Evidence for Rapid Formation of the Vapor-Dominated...  

Open Energy Info (EERE)

Formation of the Vapor-Dominated Zone at Sulphur Springs, Valles Caldera, New Mexico, USA Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article:...

360

E-Print Network 3.0 - atomic vapor density Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

T is temperature, Qris... F, is magnetic force, J is vapor plasma current density, c is speed of light, and B is magnetic flux... density. The induced magnetic force will act as...

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Tank Vapor Characterization Project: Headspace vapor characterization of Hanford waste tank 241-S-101: Results from samples collected on 06/06/96  

SciTech Connect

This report describes the analytical results of vapor samples taken from the headspace of the waste storage tank 241-S-101. The results described in this report were obtained to characterize the vapors present in the tank headspace and to support safety evaluations and tank farm operations. The results include air concentrations of selected inorganic and organic analytes and grouped compounds from samples obtained. Analyte concentrations were based on analytical results and sample volumes provided by WHC. A summary of the inorganic analytes, permanent gases, and total non-methane organic compounds is listed.

Thomas, B.L.; Evans, J.C.; Pool, K.H.; Olsen, K.B.; Fruchter, J.S.; Silvers, K.L.

1997-01-01T23:59:59.000Z

362

Sorption Behaviors of Various Organic Vapors to Argonne Premium Coal Samples  

Science Journals Connector (OSTI)

Sorption Behaviors of Various Organic Vapors to Argonne Premium Coal Samples ... Sorption of various organic vapors by Argonne Premium coals (APCS-1, 3, 5, and 8) was investigated to clarify the coal?organic interaction, sorption mechanism, and micropore and cross-linking structure of coals. ... Otake and Suuberg4 showed the behaviors of solvent swelling of Argonne premium sample coals by diffusion of various organic solvents are quite different among the coals used, which did not correlate well with coal rank. ...

Kazuhiko Shimizu; Toshimasa Takanohashi; Masashi Iino

1998-07-11T23:59:59.000Z

363

Tank 241-C-107 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-C-107. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedures that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

364

Tank 241-TY-103 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-TY-103. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedure that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

365

Tank 241-T-107 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-T-107. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedure that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

366

Tank 241-C-105 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-C-105. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedures that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

367

Tank 241-C-102 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-C-102. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedures that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

368

Tank 241-C-106 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-C-106. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedures that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

369

Tank 241-B-103 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-B-103. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedure that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

370

Tank 241-BX-104 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-BX-104. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedure that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

371

Tank 241-C-109 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-C-109. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedures that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-10T23:59:59.000Z

372

Tank 241-C-111 vapor sampling and analysis tank characterization report. Revision 1  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-C-111. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedures that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

373

Tank 241-C-110 vapor sampling and analysis tank characterization report  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-C-110. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedure that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

374

Tank 241-BY-110 vapor sampling and analysis tank characterization report. Revision 1  

SciTech Connect

This report presents the details of the Hanford waste tank characterization study for tank 241-BY-110. The drivers and objectives of the headspace vapor sampling and analysis were in accordance with procedures that were presented in other reports. The vapor and headspace gas samples were collected and analyzed to determine the potential risks to the tank farm workers due to fugitive emissions from the tank.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

375

Abstract--In electrically substituted radiometers, the ultra low noise control of the temperature is required. In this framework, we present results dedicated to the temperature regulation of copper plates, 3 cm diameter and 1 mm thick, using YBa2Cu3O7-d  

E-Print Network (OSTI)

Abstract--In electrically substituted radiometers, the ultra low noise control of the temperature wide band absolute thermometers, with mK accuracy, also needs very efficient but convenient control of the sample holder. A temperature resolution well below the mK has to be reached in that case. We present here

Paris-Sud XI, Université de

376

Cellular glass insulation keeps liquefied gas from vaporizing  

SciTech Connect

The North West Shelf Project, located on the Burrup Peninsula in Western Australia, supplies much of that vast state with natural gas for domestic and industrial applications. Some of the gas is also exported to Japan as liquefied natural gas (LNG). While awaiting shipment to Japan, the LNG is stored at {minus}322 F in four storage tanks, each with a capacity of 2.5 million ft{sup 3}. When Woodside Offshore Petroleum Pty Ltd., operator of the LNG facility, selected insulation material for the storage tanks, it went in search of a material with more than just insulating value. Since the insulation is installed inside the tanks, it must be able to resist wicking or absorbing the LNG. Also, it had to have sufficient strength to withstand the weight of the 2.5 million ft{sup 3} of LNG without being crushed or losing its insulting properties. And, as a safety precaution, the selected materials should neither burn nor support combustion. Ultimately, Woodside selected a cellular glass insulation called Foamglas, from Pittsburgh Corning Corp., that met all the performance criteria and was cost competitive with the lesser-performing alternatives. Foamglas is produced from strong, inert borosilicate glass. Its insulating capability is provided by the tiny, closed cells of air encapsulated within the foam-like structure of the glass. Since the cells are closed,neither liquid nor vapor can enter the structure of the insulation. The inert glass itself will not absorb or react with LNG, nor will it burn or support a fire. The cellular structure provides effective insulation in both not and cold applications, and offers a fire barrier.

NONE

1995-11-01T23:59:59.000Z

377

Properties of hydrogenated amorphous silicon prepared by chemical vapor deposition  

SciTech Connect

Hydrogenated amorphous silicon (a-Si:H) films were prepared by chemical vapor deposition (CVD) from mixtures of silane, disilane, trisilane, and higher polysilanes in hydrogen carrier gas at 1 atm total pressure, at substrate temperatures from 420--530 /sup 0/C. Experimental parameters are explained and properties as a function of these parameters are shown. The measurements include hydrogen content (by IR), optical, electrical, and photovoltaic properties of the material. In most respects, the CVD material closely resembles the a-Si:H usually prepared by glow discharge. The following differences have been noted: (1) the CVD a-Si:H shows no IR absorption at 840--850 cm/sup -1/, which is consistent with the expected better thermal stability of the CVD material because of the much higher substrate temperatures in the CVD process than in the glow discharge process. (2) The band gap of CVD a-Si:H is lower by about 0.1 eV than glow discharge a-Si:H of the same hydrogen content. Thus, the band gap of CVD a-Si:H is better matched to the solar spectrum than is glow discharge a-Si:H. (3) All three IR absorption bands due to hydrogen are about 20% narrower in the CVD a-Si:H, suggesting a simpler structure. (4) The temperature dependence of the dark conductivity of CVD a-Si:H fits a curve for a single activation energy, in contrast to the more complicated temperature dependence often found in glow discharge a-Si:H, in which two different activation energies are seen at high and low temperatures. This suggests that the conduction mechanism is also simpler in the CVD a-Si:H.

Ellis, F.B. Jr.; Gordon, R.G.; Paul, W.; Yacobi, B.G.

1984-06-15T23:59:59.000Z

378

Tank Vapor Characterization Project: Tank 241-BX-111 headspace gas and vapor characterization results from samples collected on August 27, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BX-111 (Tank BX-111) at the Hanford Site in Washington State. Tank headspace samples collected by Westinghouse Hanford Company (WHC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by WHC. No analytes were determined to be above the immediate notification limits specified by the sampling and analysis plan (SAP). Ammonia was the principal flammable constituent of the Tank BX-111 headspace, determined to be present at approximately 0.042 of its lower flammability limit (LFL). Total headspace flammability was estimated to be <0.157% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Pool, K.H.; Evans, J.C.; Thomas, B.L.; Sklarew, D.S. Edwards, J.A. [and others

1997-08-01T23:59:59.000Z

379

Tank Vapor Characterization Project: Tank 241-C-107 temporal study headspace gas and vapor characterization results from samples collected on September 5, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-C-107 at the Hanford Site in Washington State. Tank headspace samples collected by Westinghouse Hanford Company (WHC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by WHC. No analytes were determined to be above the immediate notification limits specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank C-107 headspace, determined to be present at approximately 1.405% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <1.519% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Pool, K.H.; Evans, J.C.; Thomas, B.L.; Edwards, J.A.; Silvers, K.L. [and others

1997-08-01T23:59:59.000Z

380

Tank Vapor Characterization Project: Tank 241-C-107 fourth temporal study: Headspace gas and vapor characterization results from samples collected on December 17, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-C-107 (Tank C-107) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurisys Service Corporation (SESC) and were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by SESC. No analytes were determined to be above the immediate notification limits specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank C-107 headspace, determined to be present at approximately 2.825% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <2.935% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Pool, K.H.; Evans, J.C.; Olsen, K.B.; Hayes, J.C. [and others

1997-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Tank Vapor Characterization Project: Tank 241-S-102 fourth temporal study: Headspace gas and vapor characterization results from samples collected on December 19, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-S-102 (Tank S-102) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurisys Service Corporation (SESC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by SESC. Ammonia was determined to be above the immediate notification limit of 150 ppm as specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank S-102 headspace, determined to be present at approximately 2.410% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <2.973% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <2.973% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Pool, K.H.; Evans, J.C.; Olsen, K.B.; Hayes, J.C. [and others

1997-08-01T23:59:59.000Z

382

Tank vapor characterization project: Tank 241-BY-101 headspace gas and vapor characterization results from samples collected on August 29, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BY-101 (Tank BY-101) at the Hanford Site in Washington State. Tank headspace samples collected by Westinghouse Hanford Company (WHC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by WHC. No analytes were determined to be above the immediate notification limits specified by the sampling and analysis plan (SAP). Total non-methane organic compounds (TNMOCs) were the principal flammable constituent of the Tank By-101 headspace, determined to be present at approximately 0.136% of the LFL. Averaged measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Evans, J.C.; Pool, K.H.; Thomas, B.L.; Olsen, K.B. [and others

1997-08-01T23:59:59.000Z

383

Tank 241-BY-108 fourth temporal study: Headspace gas and vapor characterization results from samples collected on November 14, 1997. Tank vapor characterization project  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BY-108 (Tank BY-108) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurisys Service Corporation (SESC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected nonradioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by SESC. Ammonia was determined to be above the immediate notification limit of 150 ppm specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank BY-108 headspace, determined to be present at approximately 1.390% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <2.830% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Evans, J.C.; Pool, K.H.; Olsen, K.B. [and others

1997-07-01T23:59:59.000Z

384

Tank vapor characterization project: Tank 241-BX-104 fifth temporal study: Headspace gas and vapor characterization results from samples collected on June 10, 1997  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BX-104 (Tank BX-104) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurisys Service Corporation (SESC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by SESC. Ammonia was determined to be above the immediate notification limit specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank BX-104 headspace, determined to be present at approximately 0.270% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <0.675% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Hayes, J.C.; Pool, K.H.; Evans, J.C.; Olsen, K.B. [and others

1997-07-01T23:59:59.000Z

385

Tank Vapor Characterization Project: Tank 241-BX-104 headspace gas and vapor characterization results from samples collected on August 22, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BX-104 (Tank BX-104) at the Hanford Site in Washington State. Tank headspace samples collected by Westinghouse Hanford Company (WHC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by WHC. Ammonia was determined to be above the immediate notification limit specified by the sampling and analyses plan (SAP). Total non-methane organic compounds was the principal flammable constituent of the Tank BX-104 headspace, determined to be present at approximately 0.310% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <0.784% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Evans, J.C.; Pool, K.H.; Thomas, B.L.; Olsen, K.B.; Julya, J.L. [and others

1997-08-01T23:59:59.000Z

386

Tank Vapor Characterization Project: Tank 241-BX-103 headspace gas and vapor characterization results from samples collected on August 1, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from headspace of waste storage tank 241-BX-103 (Tank BX-103) at the Hanford Site in Washington State. Tank headspace samples collected by Westinghouse Hanford Company (WHC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by WHC. No analytes were determined to be above the immediate notification limits specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank BX-103 headspace, determined to be present at approximately 0.385% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <0.633% if the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Evans, J.C.; Pool, K.H.; Thomas, B.L.; Sklarew, D.S.; Edwards, J.A. [and others] [and others

1997-08-01T23:59:59.000Z

387

Tank Vapor Characterization Project: Tank 241-BX-102 headspace gas and vapor characterization results from samples collected on July 31, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BX-102 (Tank BX-102) at the Hanford Site in Washington State. Tank headspace samples collected by Westinghouse Hanford Company (WHC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured volumes provided by WHC. No analytes were determined to be above the immediate notification limits specified by the sampling and and analysis plan. Ammonia and TNMOCs were the principal flammable constituents of the Tank BX-102 headspace, each determined to be present at approximately 0.002% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <0.107% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Pool, K.H.; Evans, J.C.; Thomas, B.L.; Olsen, K.B. Edwards, J.A. [and others

1997-08-01T23:59:59.000Z

388

Tank Vapor Characterization Project: Tank 241-BX-104 second temporal study headspace gas and vapor characterization results from samples collected on December 12, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BX-104 (Tank BX-104) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurisys Service Corporation (SESC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample provided by SESC. Ammonia was determined to be above the immediate notification limit specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank BX-104 headspace, determined to be present at approximately 0.248% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <0.645% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Pool, K.H.; Evans, J.C.; Hayes, J.C.; Olsen, K.B. [and others

1997-08-01T23:59:59.000Z

389

Tank 241-BX-104 fourth temporal study: Headspace gas and vapor characterization results from samples collected on April 7, 1997. Tank vapor characterization project  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BX-04 (Tank BX-104) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurisys Service Corporation (SESC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by SESC. Ammonia was determined to be above the immediate notification limit specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank BX-104 headspace, determined to be present at approximately 0.208% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <0.536% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Mitroshkov, A.V.; Hayes, J.C.; Evans, J.C. [and others

1997-09-01T23:59:59.000Z

390

Tank 241-BX-104 third temporal study: Headspace gas and vapor characterization results from samples collected on February 6, 1997. Tank vapor characterization project  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BX-104 (Tank BX-104) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurisys Service Corporation (SESC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by SESC. Ammonia was determined to be above the immediate notification limit specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank BX-104 headspace, determined to be present at approximately 0.178 % of its lower flammability limit (LFL). Total headspace flammability was estimated to be <0.458% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Evans, J.C.; Pool, K.H.; Hayes, J.C. [and others

1997-09-01T23:59:59.000Z

391

Tank Vapor Characterization Project: Tank 241-BY-108 temporal study headspace gas and vapor characterization results from samples collected on September 10, 1996  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-BY-108 (Tank BY-108) at the Hanford Company (WHC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by WHC. Ammonia was determined to be above the immediate notification limit of 150 ppm specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank BY-108 headspace, determined to be present at approximately 1.463% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <2.940% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Evans, J.C.; Pool, K.H.; Thomas, B.L.; Sklarew, D.S. [and others

1997-08-01T23:59:59.000Z

392

Tank 241-C-107 fifth temporal study: Headspace gas and vapor characterization results from samples collected on February 7, 1997. Tank vapor characterization project  

SciTech Connect

This report presents the results from analyses of samples taken from the headspace of waste storage tank 241-C-107 (Tank C-107) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurisys Services Corporation (SESC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by SESC. No analytes were determined to be above the immediate notification limits specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank C-107 headspace, determined to be present at approximately 3.233% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <3.342% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Hayes, J.C.; Pool, K.H.; Evans, J.C. [and others

1997-08-01T23:59:59.000Z

393

Tank vapor characterization project: Tank 241-S-102 temporal study headspace gas and vapor characterization results from samples collected on September 19, 1996  

SciTech Connect

This report presents the results from analysis of samples taken from the headspace of waste storage tank 241-S-102 (Tank S-102) at the Hanford Site in Washington State. Tank headspace samples collected by Westinghouse Hanford Company (WHC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by WHC. Ammonia was determined to be above the immediate notification limit of 150 ppm as specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank S-102 headspace, determined to be present at approximately 2.948% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <3.659% of the LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Tables S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Evans, J.C.; Pool, K.H.; Thomas, B.L.; Sklarew, D.S. [and others

1997-08-01T23:59:59.000Z

394

Effect of Water Vapor on the Oxidation Mechanisms of a Commercial Stainless Steel for Interconnect Application in High Temperature Water Vapor Electrolysis  

Science Journals Connector (OSTI)

High temperature water vapor electrolysis is one of the most promising methods...2–5 %H2O) and cathode atmospheres (10 %H2–90 %H2O). In cathode atmosphere, ageing tests performed up to 1,000 h revealed the format...

Maria Rosa Ardigo; Ioana Popa; Sébastien Chevalier; Sylvain Weber…

2013-06-01T23:59:59.000Z

395

Tank 241-S-102 fifth temporal study: Headspace gas and vapor characterization results from samples collected on February 11, 1997. Tank vapor characterization project  

SciTech Connect

This report presents tile results from analyses of samples taken from the headspace of waste storage tank 241-S-102 (Tank S-102) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurlsys Service Corporation (SESC) were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by tile Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based oil measured sample volumes provided by SESC. Ammonia was determined to be above tile immediate notification limit of 150 ppm as specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank S-102 headspace, determined to be present at approximately 1.150% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <1.624% of the LFL, Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of tile analytical results are provided in Section 3.0.

Mitroshkov, A.V.; Evans, J.C.; Hayes, J.C. [and others

1997-09-01T23:59:59.000Z

396

Tank 241-BY-108 fifth temporal study: Headspace gas and vapor characterization results from samples collected on January 30, 1997. Tank vapor characterization project  

SciTech Connect

This report presents the results from analyses of samples taken from tile headspace of waste storage tank 241-B-108 (Tank BY - 108) at the Hanford Site in Washington State. Tank headspace samples collected by SGN Eurisys Services Corporation (SESC) and analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Vapor concentrations from sorbent trap samples are based on measured sample volumes provided by SESC. Ammonia was determined to be above the immediate notification limit of 150 ppm specified by the sampling and analysis plan (SAP). Hydrogen was the principal flammable constituent of the Tank BY-108 headspace, determined to be present at approximately 0.888% of its lower flammability limit (LFL). Total headspace flammability was estimated to be <1.979% of tile LFL. Average measured concentrations of targeted gases, inorganic vapors, and selected organic vapors are provided in Table S.1. A summary of experimental methods, including sampling methodology, analytical procedures, and quality assurance and control methods are presented in Section 2.0. Detailed descriptions of the analytical results are provided in Section 3.0.

Evans, J.C.; Pool, K.H.; Olsen, K.B. [and others

1997-09-01T23:59:59.000Z

397

Vapor-Particle Separation Using Microporous Metallic Membrane in Crossflow Filtration  

SciTech Connect

Simultaneous separation of vapor and particles in industrial processes could be a key step toward manufacturing of high-quality goods. The separation is critical for successful measurement of volatile or semi-volatile aerosol particles, which no reliable technique exists. We have developed a technique for separation of vapor and particles simultaneously using a specialty microporous metallic membrane. The separator allows the thermally denuded particles traverse straight through the membrane tube, while the vapor molecules permeate through the membrane, separate from the particles and are removed subsequently. The separation technique virtually eliminates the possibility of contamination by vapor re- condensation. We tested the prototype of the vapor-particle separator (VPS) using aerosols prepared from sodium chloride to represent non-volatile aerosols. Chemical like dioctyl phthalate was chosen to represent volatile particles. The test aerosol particles were generated by an atomizer followed by a tandem differential mobility analyser to produce a stream of monodisperse particles in the size range of 10 to 100 nm. In real world particles, we tested the VPS using diesel engine particles that is a mixture of complex chemical composition. Number concentration of the nonvolatile particles reduced as the temperature increased, but the mode diameter of the aerosol population remained unchanged. Number concentration of the volatile particles was also reduced as the temperature increased, but their mode diameters became smaller as particles shrunk in diameter. Differences in the thermal behaviour of the particles were attributed to its transition energy barrier and evaporation rate. Mass balance analysis suggests the separation of vapor and test particles was reasonably complete. Thus, we conclude the VPS could provide an effective means for quantitative characterization of aerosol volatility and separation of vapors from particles.

Cheng, Mengdawn [ORNL] [ORNL

2013-01-01T23:59:59.000Z

398

Measurements of water vapor adsorption on the Geysers rocks  

SciTech Connect

The ORNL high temperature isopiestic apparatus was adapted for adsorption measurements. The quantity of water retained by rock samples taken from three different wells of The Geysers was measured at 150 °C and at 200 °C as a function of pressure in the range 0.00 ? p/p0 ? 0.98, where p0 is the saturated water vapor pressure. The rocks were crushed and sieved into three fractions of different grain sizes (with different specific surface areas). Both adsorption (increasing pressure) and desorption (decreasing pressure) runs were made in order to investigate the nature and extent of the hysteresis. Additionally, BET surface area analyses were performed by Porous Materials Inc. on the same rock samples using nitrogen or krypton adsorption measurements at 77 K. Specific surface areas and pore volumes were determined. These parameters are important in estimating water retention capability of a porous material. The same laboratory also determined the densities of the samples by helium pycnometry. Their results were then compared with our own density values obtained by measuring the effect of buoyancy in compressed argon. One of the goals of this project is to determine the dependence of the water retention capacity of the rocks as a function of temperature. The results show a significant dependence of the adsorption and desorption isotherms on the grain size of the sample. The increase in the amount of water retained with temperature observed previously (Shang et al., 1994a, 1994b, 1995) between 90 and 130°C for various reservoir rocks from The Geysers may be due to the contribution of slow chemical adsorption and may be dependent on the time allowed for equilibration. In contrast with the results of Shang et al. (1994a, 1994b, 1995), some closed and nearly closed hysteresis loops on the water adsorption/desorption isotherms (with closing points at p/p0 ? 0.6) were obtained in this study. In these cases the effects of activated processes were not present, and no increase in water adsorption with temperature was observed

Gruszkiewicz, Miroslaw S.; Horita, Juske; Simonson, John M.; Mesmer, Robert E.

1996-01-24T23:59:59.000Z

399

Measurement of Enthalpies of Vaporization of Isooctane and Ethanol Blends and Their Effects on PM Emissions from a GDI Engine  

Science Journals Connector (OSTI)

Measurement of Enthalpies of Vaporization of Isooctane and Ethanol Blends and Their Effects on PM Emissions from a GDI Engine ... The enthalpy of vaporization is very important for the performance of spark ignition engines, especially those that use gasoline direct injection (GDI). ... However, measurements reported here show that the increased enthalpy of vaporization has an adverse effect on the particulate matter (PM) emissions from a GDI engine. ...

Longfei Chen; Richard Stone

2011-02-22T23:59:59.000Z

400

Chemical-vapor deposition of complex oxides: materials and process development  

SciTech Connect

This is the final report of a six-month, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL) part of the Advanced Materials Laboratory (AML). The demand for higher performance and lower cost in electronics is driving the need for advanced materials and consequent process integration. Ceramic thin-film technology is becoming more important in the manufacture of microelectronic devices, photovoltaics, optoelectronics, magneto-optics, sensors, microwave, and radio frequency communication devices, and high-Tc superconducting tapes. A flexible processing approach for potential large-scale manufacturing of novel electronic ceramic thin films is desirable. Current thin- film deposition technologies based on physical vapor-deposition techniques are limited in scale potential and have limited control of processing parameters. The lack of control over multiple process parameters inhibits the versatility and reproducibility of the physical vapor deposition processes applied to complex oxides. Chemical vapor deposition is emerging as a viable approach for large- scale manufacturing of electronic materials. Specifically, the ability to control more processing parameters with chemical vapor deposition than with other processing techniques provides the reliability and material property reproducibility required by manufacturing. This project sought to investigate the chemical vapor deposition of complex oxides.

Muenchausen, R.

1996-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

A simple test method for measuring water vapor resistance of porous polymeric materials  

Science Journals Connector (OSTI)

Abstract A simple test method is proposed for measuring water vapor resistance of fabrics. A piece of cotton fabric connected to a container filled with distilled water through a plastic tube was used on a hot plate to generate a saturated water vapor condition on one side of the sample. The temperature of the cotton fabric (approximation of human skin covered with sweat) was measured by a thermocouple. The water vapor resistance of the sample was determined based on the water vapor pressure gradient across the sample and the heat flux. Five types of textile fabric laminated to PU/TPU membranes, plus one type of conventional fabric, were tested by using this simple apparatus as well as the sweating guarded hot plate instrument. The results showed that good agreement was observed between these two test methods. In addition, the surface temperature of the cotton ‘skin’ varied with different fabrics. This is in accordance with the actual intended situation, i.e., the skin temperature of the body is related to the ability of clothing materials to transfer water vapor. Therefore, this simple test apparatus better simulates real-life conditions than the sweating guarded hot plate instrument.

Jianhua Huang; Chang Zhang; Xiaoming Qian

2013-01-01T23:59:59.000Z

402

Raman lidar profiling of water vapor and aerosols over the ARM SGP Site  

SciTech Connect

The authors have developed and implemented automated algorithms to retrieve profiles of water vapor mixing ratio, aerosol backscattering, and aerosol extinction from Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) Raman Lidar data acquired during both daytime and nighttime operations. The Raman lidar sytem is unique in that it is turnkey, automated system designed for unattended, around-the-clock profiling of water vapor and aerosols. These Raman lidar profiles are important for determining the clear-sky radiative flux, as well as for validating the retrieval algorithms associated with satellite sensors. Accurate, high spatial and temporal resolution profiles of water vapor are also required for assimilation into mesoscale models to improve weather forecasts. The authors have also developed and implemented routines to simultaneously retrieve profiles of relative humidity. These routines utilize the water vapor mixing ratio profiles derived from the Raman lidar measurements together with temperature profiles derived from a physical retrieval algorithm that uses data from a collocated Atmospheric Emitted Radiance Interferometer (AERI) and the Geostationary Operational Environmental Satellite (GOES). These aerosol and water vapor profiles (Raman lidar) and temperature profiles (AERI+GOES) have been combined into a single product that takes advantage of both active and passive remote sensors to characterize the clear sky atmospheric state above the CART site.

Ferrare, R.A.

2000-01-09T23:59:59.000Z

403

RAMAN LIDAR PROFILING OF WATER VAPOR AND AEROSOLS OVER THE ARM SGP SITE.  

SciTech Connect

We have developed and implemented automated algorithms to retrieve profiles of water vapor mixing ratio, aerosol backscattering, and aerosol extinction from Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) Raman Lidar data acquired during both daytime and nighttime operations. This Raman lidar system is unique in that it is turnkey, automated system designed for unattended, around-the-clock profiling of water vapor and aerosols (Goldsmith et al., 1998). These Raman lidar profiles are important for determining the clear-sky radiative flux, as well as for validating the retrieval algorithms associated with satellite sensors. Accurate, high spatial and temporal resolution profiles of water vapor are also required for assimilation into mesoscale models to improve weather forecasts. We have also developed and implemented routines to simultaneously retrieve profiles of relative humidity. These routines utilize the water vapor mixing ratio profiles derived from the Raman lidar measurements together with temperature profiles derived from a physical retrieval algorithm that uses data from a collocated Atmospheric Emitted Radiance Interferometer (AERI) and the Geostationary Operational Environmental Satellite (GOES) (Feltz et al., 1998; Turner et al., 1999). These aerosol and water vapor profiles (Raman lidar) and temperature profiles (AERI+GOES) have been combined into a single product that takes advantage of both active and passive remote sensors to characterize the clear sky atmospheric state above the CART site.

FERRARE,R.A.

2000-01-09T23:59:59.000Z

404

Tank 241-C-101 vapor sampling and analysis tank characterization report  

SciTech Connect

Tank C-101 headspace gas and vapor samples were collected and analyzed to help determine the potential risks of fugitive emissions to tank farm workers. Gas and vapor samples from the Tank C-101 headspace were collected on July 7, 1994 using the in situ sampling (ISS) method, and again on September 1, 1994 using the more robust vapor sampling system (VSS). Gas and vapor concentrations in Tank C-101 are influenced by its connections to other tanks and its ventilation pathways. At issue is whether the organic vapors in Tank C-101 are from the waste in that tank, or from Tanks C-102 or C-103. Tank C-103 is on the Organic Watch List; the other two are not. Air from the Tank C-101 headspace was withdrawn via a 7.9-m long heated sampling probe mounted in riser 8, and transferred via heated tubing to the VSS sampling manifold. The tank headspace temperature was determined to be 34.0 C, and all heated zones of the VSS were maintained at approximately 50 C. Sampling media were prepared and analyzed by WHC, Oak Ridge National Laboratories, Pacific Northwest Laboratories, and Oregon Graduate Institute of Science and Technology through a contract with Sandia National Laboratories. The 39 tank air samples and 2 ambient air control samples collected are listed in Table X-1 by analytical laboratory. Table X-1 also lists the 14 trip blanks and 2 field blanks provided by the laboratories.

Huckaby, J.L.

1995-05-31T23:59:59.000Z

405

The application of expansion foam on liquefied natural gas (LNG) to suppress LNG vapor and LNG pool fire thermal radiation.  

E-Print Network (OSTI)

??Liquefied Natural Gas (LNG) hazards include LNG flammable vapor dispersion and LNG pool fire thermal radiation. A large LNG pool fire emits high thermal radiation… (more)

Suardin, Jaffee Arizon

2009-01-01T23:59:59.000Z

406

Thermal Decomposition of Molecules Relevant to Combustion and Chemical Vapor Deposition by Flash Pyrolysis Time-of-Flight Mass Spectrometry  

E-Print Network (OSTI)

of Small Molecules by Flash Pyrolysis, University ofwas performed using flash pyrolysis vacuum-ultraviolet time-Vapor Deposition by Flash Pyrolysis Time-of-Flight Mass

Lemieux, Jessy Mario

2013-01-01T23:59:59.000Z

407

Self-tuning method for monitoring the density of a gas vapor component using a tunable laser  

DOE Patents (OSTI)

The present invention relates to a vapor density monitor and laser atomic absorption spectroscopy method for highly accurate, continuous monitoring of vapor densities, composition, flow velocity, internal and kinetic temperatures and constituent distributions. The vapor density monitor employs a diode laser, preferably of an external cavity design. By using a diode laser, the vapor density monitor is significantly less expensive and more reliable than prior art vapor density monitoring devices. In addition, the compact size of diode lasers enables the vapor density monitor to be portable. According to the method of the present invention, the density of a component of a gas vapor is calculated by tuning the diode laser to a frequency at which the amount of light absorbed by the component is at a minimum or a maximum within about 50 MHz of that frequency. Laser light from the diode laser is then transmitted at the determined frequency across a predetermined pathlength of the gas vapor. By comparing the amount of light transmitted by the diode laser to the amount of light transmitted after the laser light passes through the gas vapor, the density of the component can be determined using Beer's law.

Hagans, Karla (Livermore, CA); Berzins, Leon (Livermore, CA); Galkowski, Joseph (Livermore, CA); Seng, Rita (Tracy, CA)

1996-01-01T23:59:59.000Z

408

Self-tuning method for monitoring the density of a gas vapor component using a tunable laser  

DOE Patents (OSTI)

The present invention relates to a vapor density monitor and laser atomic absorption spectroscopy method for highly accurate, continuous monitoring of vapor densities, composition, flow velocity, internal and kinetic temperatures and constituent distributions. The vapor density monitor employs a diode laser, preferably of an external cavity design. By using a diode laser, the vapor density monitor is significantly less expensive and more reliable than prior art vapor density monitoring devices. In addition, the compact size of diode lasers enables the vapor density monitor to be portable. According to the method of the present invention, the density of a component of a gas vapor is calculated by tuning the diode laser to a frequency at which the amount of light absorbed by the component is at a minimum or a maximum within about 50 MHz of that frequency. Laser light from the diode laser is then transmitted at the determined frequency across a predetermined pathlength of the gas vapor. By comparing the amount of light transmitted by the diode laser to the amount of light transmitted after the laser light passes through the gas vapor, the density of the component can be determined using Beer`s law. 6 figs.

Hagans, K.; Berzins, L.; Galkowski, J.; Seng, R.

1996-08-27T23:59:59.000Z

409

Application of two-photon laser-induced fluorescence for visualization of water vapor in combustion environments  

Science Journals Connector (OSTI)

Investigations concerning the potential for the visualization of water vapor in combustion processes have been made. The water molecules were excited through a two-photon excitation...

Neij, Hans; Aldén, Marcus

1994-01-01T23:59:59.000Z

410

Mercury Vapor At Olowalu-Ukumehame Canyon Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Mercury Vapor At Olowalu-Ukumehame Canyon Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Olowalu-Ukumehame Canyon Area (Thomas, 1986) Exploration Activity Details Location Olowalu-Ukumehame Canyon Area Exploration Technique Mercury Vapor Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes Soil mercury concentration and radon emanometry surveys were conducted along the stream beds in both Olowalu and Ukumehame Canyons and on the coastal alluvial fans (Cox and Cuff, 1981a). The results of these surveys

411

Direct-Current Resistivity Survey At Cove Fort Area - Vapor (Warpinski, Et  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Cove Fort Area - Vapor (Warpinski, Et Direct-Current Resistivity Survey At Cove Fort Area - Vapor (Warpinski, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Cove Fort Area (Warpinski, Et Al., 2004) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Update to Warpinski, et al., 2002 References N. R. Warpinski, A. R. Sattler, R. Fortuna, D. A. Sanchez, J. Nathwani (2004) Geothermal Resource Exploration And Definition Projects Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_Survey_At_Cove_Fort_Area_-_Vapor_(Warpinski,_Et_Al.,_2004)&oldid=598134"

412

Measurements of the Infrared SpectraLines of Water Vapor at Atmospheric Temperatures  

NLE Websites -- All DOE Office Websites (Extended Search)

Measurements of the Infrared Spectral Lines Measurements of the Infrared Spectral Lines of Water Vapor at Atmospheric Temperatures P. Varanasi and Q. Zou Institute for Terrestrial and Planetary Atmospheres State University of New York at Stony Brook Stony Brook, New York Introduction Water vapor is undoubtedly the most dominant greenhouse gas in the terrestrial atmosphere. In the two facets of Atmospheric Radiation Measurement (ARM) Program research, atmospheric remote sensing (air-borne as well as Cloud and Radiation Testbed [CART] site-based) and modeling of atmospheric radiation, the spectrum of water vapor, ranging from the microwave to the visible wavelengths, plays a significant role. Its spectrum has been the subject of many studies throughout the last century. Therefore, it is natural to presume it should be fairly well established by now. However, the need for a

413

Mercury Vapor At Kilauea East Rift Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

Mercury Vapor At Kilauea East Rift Area (Thomas, Mercury Vapor At Kilauea East Rift Area (Thomas, 1986) Exploration Activity Details Location Kilauea East Rift Area Exploration Technique Mercury Vapor Activity Date Usefulness not indicated DOE-funding Unknown Notes The sampling network for soil mercury concentrations undertaken by Cox (1981) identified a complicated pattern of mercury concentrations throughout the lower Puna area (Fig. 60). The highest soil mercury concentrations found were generally located within the rift zone, but an analysis of the data showed that soil type and soil pH also had a marked impact on mercury concentration. Making corrections for these effects improved the correspondence between the surface geological expression of the rift zone and the mercury concentrations observed; interpretation of

414

Mercury Vapor At Mauna Loa Northeast Rift Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

Mauna Loa Northeast Rift Area (Thomas, 1986) Mauna Loa Northeast Rift Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Mercury Vapor At Mauna Loa Northeast Rift Area (Thomas, 1986) Exploration Activity Details Location Mauna Loa Northeast Rift Area Exploration Technique Mercury Vapor Activity Date Usefulness not indicated DOE-funding Unknown Notes Soil mercury and radon emanometry sampling conducted in the Keaau prospect were similarly unable to define any anomalies that could reasonably be interpreted to be due to subsurface thermal effects. References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In Hawaii Retrieved from "http://en.openei.org/w/index.php?title=Mercury_Vapor_At_Mauna_Loa_Northeast_Rift_Area_(Thomas,_1986)&oldid=390060

415

Posters Toward an Operational Water Vapor Remote Sensing System Using the Global Positioning System  

NLE Websites -- All DOE Office Websites (Extended Search)

3 3 Posters Toward an Operational Water Vapor Remote Sensing System Using the Global Positioning System S. I. Gutman, (a) R. B. Chadwick, (b) and D. W. Wolf (c) National Oceanic and Atmospheric Administration Boulder, Colorado A. Simon Cooperative Institute for Research in Environmental Science Boulder, Colorado T. Van Hove and C. Rocken University Navstar Consortium Boulder, Colorado Background Water vapor is one of the most important constituents of the free atmosphere since it is the principal mechanism by which moisture and latent heat are transported and cause "weather." The measurement of atmospheric water vapor is essential for weather and climate research as well as for operational weather forecasting. An important goal in modern weather prediction is to improve the accuracy of short-term

416

Preconcentrator with high volume chiller for high vapor pressure particle detection  

SciTech Connect

Apparatus and method for collecting particles of both high and low vapor pressure target materials entrained in a large volume sample gas stream. Large volume active cooling provides a cold air supply which is mixed with the sample gas stream to reduce the vapor pressure of the particles. In embodiments, a chiller cools air from ambient conditions to 0-15.degree. C. with the volumetric flow rate of the cold air supply being at least equal to the volumetric flow rate of the sample gas stream. In further embodiments an adsorption media is heated in at least two stages, a first of which is below a threshold temperature at which decomposition products of the high vapor pressure particle are generated.

Linker, Kevin L

2013-10-22T23:59:59.000Z

417

The Luminosity of Mercury Vapor Distilled from the Arc in Vacuo.  

Science Journals Connector (OSTI)

Afterglow of Mercury Vapor from an Arc in Vacuum.—(1) The effect of an electric field on the spectrum was studied. It was found that charged grids decreased the luminosity without changing the color; but when, under certain conditions, the luminosity was increased, there was a change in the relative intensity of the lines. (2) The velocity of the vapor was measured by a stroboscopic method. The luminosity was decreased intermittently at a known frequency and the resulting "puffs" as they moved along the tube, were observed stroboscopically. From this velocity and the rate of distillation, the density of the vapor was computed. (3) Decay of luminosity along the tube was observed. (4) Theoretical discussion of these results leads to the conclusion that recombination of the positive and negative ions produced by the discharge, is the most probable cause of the afterglow.

Norman H. Ricker

1921-02-01T23:59:59.000Z

418

A simple grand canonical approach to compute the vapor pressure of bulk and finite size systems  

SciTech Connect

In this article we introduce a simple grand canonical screening (GCS) approach to accurately compute vapor pressures from molecular dynamics or Monte Carlo simulations. This procedure entails a screening of chemical potentials using a conventional grand canonical scheme, and therefore it is straightforward to implement for any kind of interface. The scheme is validated against data obtained from Gibbs ensemble simulations for water and argon. Then, it is applied to obtain the vapor pressure of the coarse-grained mW water model, and it is shown that the computed value is in excellent accord with the one formally deduced using statistical thermodynamics arguments. Finally, this methodology is used to calculate the vapor pressure of a water nanodroplet of 94 molecules. Interestingly, the result is in perfect agreement with the one predicted by the Kelvin equation for a homogeneous droplet of that size.

Factorovich, Matías H.; Scherlis, Damián A. [Departamento de Química Inorgánica, Analítica y Química Física/INQUIMAE, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pab. II, Buenos Aires C1428EHA (Argentina)] [Departamento de Química Inorgánica, Analítica y Química Física/INQUIMAE, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pab. II, Buenos Aires C1428EHA (Argentina); Molinero, Valeria [Department of Chemistry, University of Utah, 315 South 1400 East, Salt Lake City, Utah 84112-0850 (United States)] [Department of Chemistry, University of Utah, 315 South 1400 East, Salt Lake City, Utah 84112-0850 (United States)

2014-02-14T23:59:59.000Z

419

Shock formation in the collapse of a vapor nano-bubble  

E-Print Network (OSTI)

In this paper a diffuse-interface model featuring phase change, transition to supercritical conditions, thermal conduction, compressibility effects and shock wave propagation is exploited to deal with the dynamics of a cavitation bubble. At variance with previous descriptions, the model is uniformly valid for all phases (liquid, vapor and supercritical) and phase transitions involved, allowing to describe the non-equilibrium processes ongoing during the collapse. As consequence of this unitary description, rather unexpectedly for pure vapor bubbles, the numerical experiments show that the collapse is accompanied by the emission of a strong shock wave in the liquid and by the oscillation of the bubble that periodically disappears and reappears, due to transition to super/sub critical conditions. The mechanism of shock wave formation is strongly related to the transition of the vapor to supercritical state, with a progressive steepening of the compression wave to form the shock which is eventually reflected as ...

Magaletti, Francesco; Casciola, Carlo Massimo

2014-01-01T23:59:59.000Z

420

Evaluation of the 3M Organic Vapor Monitor #3500 as a sampling device for ethyl acrylate and the effect of discontinued exposure on vapor retention  

E-Print Network (OSTI)

Sampling Theories of Adsorption Forces of Adsorption Activation Procedures Surface Structure Statement of Hypotheses METHODOLOGV Test Atmosphere Generation Exposure Chamber MIRAN Calibration and Use Monitor Exposure to EA Analytical Procedures...EVALUATION OF THE 3M ORGANIC VAPOR MONITOR 53500 AS A SAMPLING DEVICE FOR ETHYL ACRYLATE AND THE EFFECT OF DISCONTINUED EXPOSURE ON VAPOP, RETENTION A Thesis by ROBERT WAYNE BARR Submitted to the Graduate College of Texas Al!M University...

Barr, Robert Wayne

2012-06-07T23:59:59.000Z

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Vertical Variability of Aerosols and Water Vapor Over the Southern Great Plains  

NLE Websites -- All DOE Office Websites (Extended Search)

Vertical Variability of Aerosols and Water Vapor Vertical Variability of Aerosols and Water Vapor Over the Southern Great Plains R. A. Ferrare National Aeronautics and Space Administration Langley Research Center Hampton, Virginia D. D. Turner Pacific Northwest National Laboratory Richland, Washington M. Clayton and V. Brackett Science Applications International Corporation National Aeronautics and Space Administration Langley Research Center Hampton, Virginia T. P. Tooman and J. E. M. Goldsmith Sandia National Laboratories Livermore, California J. A. Ogren National Oceanic and Atmospheric Administration Climate Monitoring and Diagnostics Laboratory Boulder, Colorado E. Andrews Cooperative Institute for Research in Environmental Sciences University of Colorado Boulder, Colorado

422

Microsoft Word - Vapor Phase Elemental Sulfur Tech Brief DRAFT bbl 08-24.docx  

NLE Websites -- All DOE Office Websites (Extended Search)

AT A GLANCE AT A GLANCE ï‚· eliminates excavation expense ï‚· applicable to large or small sites ï‚· straightforward deployment ï‚· uses heat to distribute sulfur throughout a soil ï‚· mercury reacts with sulfur to form immobile and insoluble minerals ï‚· patent applied for TechBrief Vapor Phase Elemental Sulfur Amendment for Sequestering Mercury in Contaminated Soil Scientists at the Savannah River National Laboratory (SRNL) have identified a method of targeting mercury in contaminated soil zone by use of sulfur vapor heated gas. Background Mercury contamination in soil is a common problem in the environment. The most common treatment is excavation - a method that works well for small sites where the

423

Preparation of membranes using solvent-less vapor deposition followed by in-situ polymerization  

DOE Patents (OSTI)

A system of fabricating a composite membrane from a membrane substrate using solvent-less vapor deposition followed by in-situ polymerization. A first monomer and a second monomer are directed into a mixing chamber in a deposition chamber. The first monomer and the second monomer are mixed in the mixing chamber providing a mixed first monomer and second monomer. The mixed first monomer and second monomer are solvent-less vapor deposited onto the membrane substrate in the deposition chamber. The membrane substrate and the mixed first monomer and second monomer are heated to produce in-situ polymerization and provide the composite membrane.

O'Brien, Kevin C. (San Ramon, CA); Letts, Stephan A. (San Ramon, CA); Spadaccini, Christopher M. (Oakland, CA); Morse, Jeffrey C. (Pleasant Hill, CA); Buckley, Steven R. (Modesto, CA); Fischer, Larry E. (Los Gatos, CA); Wilson, Keith B. (San Ramon, CA)

2012-01-24T23:59:59.000Z

424

Solar-induced chemical vapor deposition of diamond-type carbon films  

DOE Patents (OSTI)

An improved chemical vapor deposition method for depositing transparent continuous coatings of sp[sup 3]-bonded diamond-type carbon films, comprises: (a) providing a volatile hydrocarbon gas/H[sub 2] reactant mixture in a cold wall vacuum/chemical vapor deposition chamber containing a suitable substrate for said films, at pressure of about 1 to 50 Torr; and (b) directing a concentrated solar flux of from about 40 to about 60 watts/cm[sup 2] through said reactant mixture to produce substrate temperatures of about 750 C to about 950 C to activate deposition of the film on said substrate. 11 figs.

Pitts, J.R.; Tracy, C.E.; King, D.E.; Stanley, J.T.

1994-09-13T23:59:59.000Z

425

A study of the mixed association of cholesterol with methyl cholate by vapor pressure osmometry  

E-Print Network (OSTI)

out on a Knauer Vapor Pressure Osmometer equipped w1th the Knauer Universal Temperature Measuring Apparatus (a sensitive Wheatstone bridge with a 10-turn helical potentiometer) and a chart recorder. A thorough discussion of some of the experimental... at the desired temperature. Two themistors are mounted in the chamber and are coupled to the Wheatstone bridge. Using syr1nges, a drop of pure solvent is placed on one themistor and a drop of solution on the other. Because of the lowering of solvent vapor...

Foster, Bruce William

1981-01-01T23:59:59.000Z

426

The exchange rate for tritiated water vapor adsorbed on silica gel  

E-Print Network (OSTI)

THE EXCHANGE RATE FOR TRITIATED WATER VAPOR ADSORBED ON SILICA GEL A Thesis by PENNY ALANE SHAMBLIN Submitted to the Cnaduate College of Texas A8cM University in partial fulfihmnt of the requirements for the degree of MASTER OF SCIENCE... December 1987 Major Subject: Health Physics THE EXCHANGE RATE FOR ~TED WATER VAPOR ADSORBED ON SILICA GEL A Thesis by PENNY ALANE SHAMBUN Approved as to style and content by: Milton E. McLain (Chair of Committee) Gerald A. Schla (Member) Ric ard...

Shamblin, Penny Alane

2012-06-07T23:59:59.000Z

427

CORRELATIONS BETWEEN VAPOR SATURATION, FLUID COMPOSITION, AND WELL DECLINE IN LARDERELLO  

SciTech Connect

A large body of field data from Larderello shows striking temporal correlations between decline of well flow-rate, produced gas/steam ratio, chloride concentration and produced vapor fraction. The latter is inferred from measured concentrations of non-condensible gases in samples of well fluid, using chemical phase equilibrium principles. Observed temporal changes in the vapor fractions can be interpreted in term of a ''multiple source'' model, as suggested by D'Amore and Truesdell (1979). This provides clues to the dynamics of reservoir depletion, and to the evaluation of well productivity and longevity.

D'Amore, F.; Pruess, K.

1985-01-22T23:59:59.000Z

428

Characteristics of countercurrent vapor-liquid flow at a perforated plate  

E-Print Network (OSTI)

of heat-sens1tive materials. Also, a column with low liqu1d holdup is more responsive to operating controls than 1s a column conta1n- 1ng a large inventory of liquid. It was found that for the plates having hole areas of 23 and 40 per cent... to the plate above by the impetus of the vapor Jetting through the liquid on the plate. In this case, the velocity of the vapor through the holes in the plate, (or slots, in the case of bubble-caps) would be the 38 controlling factor. This mechanism...

Sutherland, Samuel Shelton

2012-06-07T23:59:59.000Z

429

Solar-induced chemical vapor deposition of diamond-type carbon films  

DOE Patents (OSTI)

An improved chemical vapor deposition method for depositing transparent continuous coatings of sp.sup.3 -bonded diamond-type carbon films, comprising: a) providing a volatile hydrocarbon gas/H.sub.2 reactant mixture in a cold wall vacuum/chemical vapor deposition chamber containing a suitable substrate for said films, at pressure of about 1 to 50 Torr; and b) directing a concentrated solar flux of from about 40 to about 60 watts/cm.sup.2 through said reactant mixture to produce substrate temperatures of about 750.degree. C. to about 950.degree. C. to activate deposition of the film on said substrate.

Pitts, J. Roland (Lakewood, CO); Tracy, C. Edwin (Golden, CO); King, David E. (Lakewood, CO); Stanley, James T. (Beaverton, OR)

1994-01-01T23:59:59.000Z

430

Materials, methods and devices to detect and quantify water vapor concentrations in an atmosphere  

DOE Patents (OSTI)

We have demonstrated that a surface acoustic wave (SAW) sensor coated with a nanoporous framework material (NFM) film can perform ultrasensitive water vapor detection at concentrations in air from 0.05 to 12,000 ppmv at 1 atmosphere pressure. The method is extendable to other MEMS-based sensors, such as microcantilevers, or to quartz crystal microbalance sensors. We identify a specific NFM that provides high sensitivity and selectivity to water vapor. However, our approach is generalizable to detection of other species using NFM to provide sensitivity and selectivity.

Allendorf, Mark D; Robinson, Alex L

2014-12-09T23:59:59.000Z

431

Isobaric vapor-liquid equilibria in the system methyl propanoate + n-butyl alcohol  

SciTech Connect

Isobaric vapor-liquid equilibria were determined at 74.66, 101.32, and 127.99 kPa for binary mixtures containing methyl propanoate + n-butyl alcohol by using a dynamic still with vapor and liquid circulation. No azeotrope was detected. The data were found to be thermodynamically consistent according to the point to point test. Application of the group-contribution models ASOG, UNIFAC, and modified UNIFAC to the activity coefficients at the three pressures studied gives average errors of less than 10%, 11%, and 3%, respectively.

Susial, P.; Ortega, J. (Univ. de Las Palmas de Gran Canaria, Canary Islands (Spain). Lab. de Termodinamica y Fisicoquimica)

1993-10-01T23:59:59.000Z

432

Tank Vapor Characterization Project: Headspace vapor characterization of Hanford Waste Tank 241-C-204: Results from samples collected on 07/02/96  

SciTech Connect

This report describes the analytical results of vapor samples taken from the headspace of the waste storage tank 241-C-204 (Tank C-204) at the Hanford Site in Washington State. The results described in this report were obtained to characterize the vapors present in the tank headspace and to support safety evaluations and tank farm operations. The results include air concentrations of selected inorganic and organic analytes and grouped compounds from samples obtained by Westinghouse Hanford Company (WHC) and provided for analysis to Pacific Northwest National Laboratory (PNNL). Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Analyte concentrations were based on analytical results and, where appropriate, sample volumes provided by WHC. A summary of the inorganic analytes, permanent gases, and total non-methane organic compounds is listed in Table S.1. The three highest concentration analytes detected in SUMMA{trademark} canister and triple sorbent trap samples are also listed in Table S.1. Detailed descriptions of the analytical results appear in the appendices.

Thomas, B.L.; Evans, J.C.; Pool, K.H. [and others

1997-01-01T23:59:59.000Z

433

Tank Vapor Characterization Project: Headspace vapor characterization of Hanford Tank 241-B-105: Results from samples collected on 07/30/96  

SciTech Connect

This report describes the analytical results of vapor samples taken from the headspace of the waste storage tank 241-B-105 (Tank B-105) at the Hanford Site in Washington State. The results described in this report were obtained to characterize the vapors present in the tank headspace and to support safety evaluations and tank farm operations. The results include air concentrations of selected inorganic and organic analytes and grouped compounds from samples obtained by Westinghouse Hanford Company (WHC) and provided for analysis to Pacific Northwest National Laboratory (PNNL). Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Analyte concentrations were based on analytical results and, where appropriate, sample volumes provided by WHC. A summary of the inorganic analytes, permanent gases, and total non-methane organic compounds is listed in Table S.1. The three highest concentration analytes detected in SUMMA{trademark} canister and triple sorbent trap samples are also listed in Table S.1. Detailed descriptions of the analytical results appear in the appendices.

Pool, K.H.; Evans, J.C.; Thomas, B.L. [and others

1997-01-01T23:59:59.000Z

434

Tank Vapor Characterization Project: Headspace vapor characterization of Hanford Waste Tank 241-S-103: Results from samples collected on 06/12/96  

SciTech Connect

This report describes the analytical results of vapor samples taken from the headspace of the waste storage tank 241-S-103 (Tank S-103) at the Hanford Site in Washington State. The results described in this report were obtained to characterize the vapors present in the tank headspace and to support safety evaluations and tank farm operations. The results include air concentrations of selected inorganic and organic analytes and grouped compounds from samples obtained by Westinghouse Hanford Company (WHC) and provided for analysis to Pacific Northwest National Laboratory (PNNL). Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Analyte concentrations were based on analytical results and, where appropriate, sample volumes provided by WHC. A summary of the inorganic analytes, permanent gases, and total non-methane organic compounds is listed in Table S.1. The three highest concentration analytes detected in SUMMA{trademark} canister and triple sorbent trap samples are also listed in Table S.1. Detailed descriptions of the analytical results appear in the appendices.

Evans, J.C.; Pool, K.H.; Thomas, B.L. [and others

1997-01-01T23:59:59.000Z

435

Tank Vapor Characterization Project: Headspace vapor characterization of Hanford Tank 241-TY-102: Results from samples collected on 04/12/96  

SciTech Connect

This report describes the analytical results of vapor samples taken from the headspace of the waste storage tank 241-TY-102 (Tank TY-102) at the Hanford Site in Washington State. The results described in this report were obtained to`characterize the vapors present in the tank headspace and to support safety evaluations and tank farm operations. The results include air concentrations of selected inorganic and organic analytes, and grouped compounds from samples obtained by Westinghouse Hanford Company (WHC) and provided for analysis to Pacific Northwest National Laboratory (PNNL). Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Analyte concentrations were based on analytical results and, where appropriate, sample volumes provided by WHC. A summary of the inorganic analytes, permanent gases, and total non-methane organic compounds is listed in Table S.1. The three highest concentration analytes detected in SUMMA{trademark} canister and triple sorbent trap samples are also listed in Table S.1. Detailed descriptions of the analytical results appear in the appendices.

Evans, J.C.; Pool, K.H.; Thomas, B.L. [and others

1997-01-01T23:59:59.000Z

436

An Examination of the Thermodynamics of Fusion, Vaporization, and Sublimation of (R,S)-and (R)-Flurbiprofen by Correlation  

E-Print Network (OSTI)

An Examination of the Thermodynamics of Fusion, Vaporization, and Sublimation of (R,S)- and (R)-Flurbiprofen by Correlation Gas Chromatography PATAMAPORN UMNAHANANT, DARRELL HASTY, JAMES CHICKOS Department of Chemistry (wileyonlinelibrary.com). DOI 10.1002/jps.23094 ABSTRACT: The vaporization, fusion, and sublimation enthalpies of (R

Chickos, James S.

437

Influence of gas composition on wafer temperature in a tungsten chemical vapor deposition reactor: Experimental measurements, model  

E-Print Network (OSTI)

Influence of gas composition on wafer temperature in a tungsten chemical vapor deposition reactor-wafer, lamp-heated chemical vapor deposition system were used to study the wafer temperature response to gas composition. A physically based simulation procedure for the process gas and wafer temperature was developed

Rubloff, Gary W.

438

Sorption-caused attenuation and delay of water-vapor signals in eddy-covariance sampling tubes and filters  

Science Journals Connector (OSTI)

Adsorption and desorption (together sorption) processes in sampling tubes and filters of eddy-covariance stations cause attenuation and delay of water-vapor signals, leading to underestimation of water-vapor fluxes by tens of per cent. The aim of ...

Annika Nordbo; Pekka Kekäläinen; Erkki Siivola; Ivan Mammarella; Jussi Timonen; Timo Vesala

439

Substrate effect on CdTe layers grown by metalorganic vapor phase N. V. Sochinskiia),b)  

E-Print Network (OSTI)

Substrate effect on CdTe layers grown by metalorganic vapor phase epitaxy N. V. Sochinskiia for publication 30 December 1996 CdTe layers were grown by metalorganic vapor phase epitaxy MOVPE on different substrates like sapphire, GaAs, and CdTe wafers. The growth was carried out at the temperature 340 °C

Viña, Luis

440

Molecular Simulation of Henry's Constant at Vapor-Liquid and Liquid-Liquid Phase Richard J. Sadus  

E-Print Network (OSTI)

coexistence. 1. Introduction Henry's constant is a well-known measure of a solute's solubility in a particularMolecular Simulation of Henry's Constant at Vapor-Liquid and Liquid-Liquid Phase Boundaries Richard to determine Henry's constant from the residual chemical potential at infinite dilution at the vapor-liquid

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

CRYSTALLINE SILICON THIN-FILM SOLAR CELLS FROM THE POROUS SILICON PROCESS APPLYING CONVECTION ASSISTED CHEMICAL VAPOR DEPOSITION  

E-Print Network (OSTI)

CRYSTALLINE SILICON THIN-FILM SOLAR CELLS FROM THE POROUS SILICON PROCESS APPLYING CONVECTION ASSISTED CHEMICAL VAPOR DEPOSITION Barbara Terheiden,1* Thomas Kunz,2 Ingo Burkert2 , Renate Horbelt,1, D-91058 Erlangen, Germany ABSTRACT: Convection assisted chemical vapor deposition (CoCVD) is applied

442

Water Vapor Transport and Moisture Budget over Eastern China: Remote Forcing from the Two Types of El Niño  

Science Journals Connector (OSTI)

The water vapor transport and moisture budget over eastern China remotely forced by the cold-tongue (CT) and warm-pool (WP) El Niño show striking differences throughout their lifetime. The water vapor transport response is weak in the developing ...

Xiuzhen Li; Wen Zhou; Deliang Chen; Chongyin Li; Jie Song

2014-12-01T23:59:59.000Z

443

Distributed Porosity as a Control Parameter for Oxide Thermal Barriers Made by Physical Vapor Deposition  

E-Print Network (OSTI)

Anthony G. Evans* Materials Institute, Princeton University, Princeton, New Jersey 08544 Thermal barrier and generating new thermal resistance solutions, as appropri- ate. A continuum heat flow analysis is usedDistributed Porosity as a Control Parameter for Oxide Thermal Barriers Made by Physical Vapor

Wadley, Haydn

444

Measurement of Water Vapor Concentration using Tunable Diode Laser Absorption Spectroscopy  

E-Print Network (OSTI)

Tunable diode laser spectroscopy and the Beer-Lambert relation has been used to measure the absorption of water vapor both in an absorption cell and in a shock tube. The purpose of this thesis is to develop a laser diagnostic capable of determining...

Barrett, Alexander B.

2010-07-14T23:59:59.000Z

445

Pulsed plasma-Used injection sources for remote plasma activated chemical vapor deposition  

E-Print Network (OSTI)

Pulsed plasma- Used injection sources for remote plasma activated chemical vapor deposition Mark J, Urbana, Illinois 61801 (Received 21 October 1992; accepted for publication 12 January 1993) Remote plasma the substrate is immersed in the plasma. This selectivity can be compromised if the deposition gases, which

Kushner, Mark

446

High-expansion foam for LNG vapor mitigation. Topical report, September 1987-December 1989  

SciTech Connect

One of the purposes of these high expansion foam systems is to reduce the extent of the hazardous vapor cloud generated during an accidental LNG release. Should the LNG ignite, these systems serve the additional function of controlling the LNG fire and minimizing its radiation to the surroundings. Foam generators have been installed along the tops of dike walls surrounding some LNG storage tanks, and around other fenced containment areas where LNG may be accidentally released, such as LNG pump pits and pipe rack trenches. To date there are no technically justifiable guidelines for the design and installation of these systems. Furthermore, there are no models that may be used describe the vapor source so as to be able to predict the reduction in the hazardous vapor cloud zone when high expansion foam is applied to an LNG spill. Information is essential not only for the optimal design of high expansion foam systems, but also for comparing the cost effectiveness of alternative LNG vapor mitigation measures.

Atallah, S.; Shah, J.N.; Peterlinz, M.E.

1990-05-01T23:59:59.000Z

447

Adsorption of NaCl Vapor at Elevated Temperature on Mineral Adsorbents  

Science Journals Connector (OSTI)

All adsorbents were crunched and sieved to ?1.00–1.25 mm adsorbent granularity used in the experiments. ... NaCl vapor was adsorbed at 1123 K for 5 h by each adsorbent. ... In the presence of chemical adsorption Na+ and Cl? would selectively adsorb and Na+ and Cl? would exist with a different molecule. ...

Yili Li; Jian Li; Shuiyuan Cheng; Wenjun Liang; Yuquan Jin; Youqing Wu; Jinsheng Gao

2007-09-21T23:59:59.000Z

448

Cobalt Ultrathin Film Catalyzed Ethanol Chemical Vapor Deposition of Single-Walled Carbon Nanotubes  

E-Print Network (OSTI)

Cobalt Ultrathin Film Catalyzed Ethanol Chemical Vapor Deposition of Single-Walled Carbon Nanotubes (SWNTs) using a cobalt ultrathin film (1 nm) as the catalyst and ethanol as carbon feedstock flow during the growth. The trace amount of self-contained water (0.2-5 wt %) in ethanol may act

Hone, James

449

Epitaxial graphene prepared by chemical vapor deposition on single crystal thin iridium films on sapphire  

E-Print Network (OSTI)

Epitaxial graphene prepared by chemical vapor deposition on single crystal thin iridium films Cedex 9, France (Dated: 15 March 2011) Uniform single layer graphene was grown on single-crystal Ir. These graphene layers have a single crystallographic orientation and a very low density of defects, as shown

Boyer, Edmond

450

Observation of picosecond superfluorescent pulses in rubidium atomic vapor pumped by 100-fs laser pulses  

E-Print Network (OSTI)

We study the superfluorescence (SF) from a gas of rubidium atoms. The atoms of a dense vapor are excited to the 5D state from the 5S state by a two-photon process driven by 100-fs laser pulses. The atoms decay to the 6P state and then to the 5S...

Ariunbold, Gombojav O.; Kash, Michael M.; Sautenkov, Vladimir A.; Li, Hebin; Rostovtsev, Yuri V.; Welch, George R.; Scully, Marlan O.

2010-01-01T23:59:59.000Z

451

Luminescent Properties of CdS Crystals Doped with Gallium and Tellurium in Cadmium Vapor  

Science Journals Connector (OSTI)

A technique is devised for vapor-phase doping CdS in the quaternary system Cd–Ga–Te–S. CdS crystals are doped with Ga and Te via four-zone ... and Cd (the more volatile component of CdS). The luminescence spectra...

I. N. Odin; M. V. Chukichev; M. E. Rubina

2003-07-01T23:59:59.000Z

452

Lattice Boltzmann method for modeling liquid-vapor interface configurations in porous media  

E-Print Network (OSTI)

Lattice Boltzmann method for modeling liquid-vapor interface configurations in porous media Michael; published 13 January 2004. [1] The lattice Boltzmann method (LBM) has emerged as a powerful tool: Modeling; 3230 Mathematical Geophysics: Numerical solutions; KEYWORDS: Lattice Boltzmann Citation: Sukop, M

Sukop, Mike

453

Semi-insulating crystalline silicon formed by oxygen doping during low-temperature chemical vapor deposition  

E-Print Network (OSTI)

Semi-insulating crystalline silicon formed by oxygen doping during low-temperature chemical vapor) In this letter we demonstrate the use of oxygen as a dopant in silicon to create semi-insulating, crystalline of the films exhibit classical characteristics of space-charge-limited current associated with insulators

454

An atomic-scale analysis of catalytically-assisted chemical vapor deposition of carbon nanotubes  

E-Print Network (OSTI)

An atomic-scale analysis of catalytically-assisted chemical vapor deposition of carbon nanotubes M Growth of carbon nanotubes during transition-metal particles catalytically-assisted thermal decomposition of various nanotube surface and edge reactions (e.g. adsorption of hydrocarbons and hydrogen onto the surface

Grujicic, Mica

455

Summary Weusedthreemethodstomeasureboundarylayer conductance to heat transfer (gbH) and water vapor transfer  

E-Print Network (OSTI)

Summary Weusedthreemethodstomeasureboundarylayer conductance to heat transfer (gbH) and water vapor of transpiration). The boundary layer conductance to heat transfer is small enough that leaf temperature can become diffusion, the boundary layer around a leaf also provides resistance to the transfer of heat between a leaf

Martin, Timothy

456

High-rate chemical vapor deposition of nanocrystalline silicon carbide films by radio frequency thermal plasma  

E-Print Network (OSTI)

High-rate chemical vapor deposition of nanocrystalline silicon carbide films by radio frequency Semiconductor, Eden Prairie, MN, USA Received 10 July 2002; accepted 14 July 2002 Abstract Silicon carbide films; Nanomaterials; Silicon carbide; Thermal plasmas; Thin films; Si tetrachlorine precursor Silicon carbide has

Zachariah, Michael R.

457

Simulation and Validation of Vapor Compression System Faults and Start-up/Shut-down Transients  

E-Print Network (OSTI)

-up/shutdown have been performed using the vapor compression system models developed in MATLAB/Simulink environment and validated against the 3-ton air conditioning unit present in the Thermo-Fluids Control Laboratory at Texas A & M University. The simulation...

Ayyagari, Balakrishna

2012-10-19T23:59:59.000Z

458

2.1 RAMAN LIDAR PROFILING OF WATER VAPOR AND AEROSOLS OVER THE ARM SGP SITE  

E-Print Network (OSTI)

with satellite sensors. Accurate, high spatial and temporal resolution profiles of water vapor are also required+GOES) have been combined into a single product that takes advantage of both active and passive remote sensors with the use of narrowband (~0.4 nm bandpass) filters, reduces the background skylight and, therefore

459

Water Vapor and Mechanical Work: A Comparison of Carnot and Steam Cycles OLIVIER PAULUIS  

E-Print Network (OSTI)

by the corresponding Carnot cycle. The Carnot and steam cycles can be combined into a mixed cycle that is forcedWater Vapor and Mechanical Work: A Comparison of Carnot and Steam Cycles OLIVIER PAULUIS Center in the atmosphere is discussed here by comparing two idealized heat engines: the Carnot cycle and the steam cycle

Pauluis, Olivier M.

460

Patterned growth of single-walled carbon nanotube arrays from a vapor-deposited Fe catalyst  

E-Print Network (OSTI)

Patterned growth of single-walled carbon nanotube arrays from a vapor-deposited Fe catalyst H. B deposition using low-coverage vacuum-deposited iron as a catalyst. Ordered arrays of suspended nanotubes constructed directly on contacting metal electrodes of Pt/Cr patterned with catalysts. Patterning with solid

Golovchenko, Jene A.

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

VAPOR COMPRESSION HEAT PUMP SYSTEM FIELD TESTS AT THE TECH COMPLEX  

E-Print Network (OSTI)

323 CHAPTER 17 VAPOR COMPRESSION HEAT PUMP SYSTEM FIELD TESTS AT THE TECH COMPLEX \\B E Van D for several novel and conventional heat pump systems for space conditioning and water heating. Systems tested include the Annual Cycle Energy System (ACES), solar assisted heat pumps (SAHP) both parallel and series

Oak Ridge National Laboratory

462

Water Vapor Radiometry : Outline of Goals and Tasks for the Spring Semester 2001  

E-Print Network (OSTI)

that can accu­ rately measure the spectrum of the water vapor emis­ sion. The current receivers follow, as in a conventional re­ ceiver, the correlation receiver splits the rf signal into two with a splitter that follows the feed horn. Both branches are mixed with a carefully controlled ther­ mal load. A 180 ffi phase shift

Backer, Don

463

Study of the Effects of Obstacles in Liquefied Natural Gas (LNG) Vapor Dispersion using CFD Modeling  

E-Print Network (OSTI)

by enhanced mixing. Through parametric analysis it is demonstrated that height, width and shape of the obstacles play an important role in the vapor concentration reduction. The findings of this research may be applied in the design stage of an LNG terminal...

Ruiz Vasquez, Roberto

2012-10-19T23:59:59.000Z

464

Initiated chemical vapor deposition of fluoropolymer coatings for the surface modification of complex geometries  

E-Print Network (OSTI)

Initiated chemical vapor deposition (iCVD) is a one-step, soventless process that can be used to produce polymeric thin films. The iCVD technique has been used to polymerize a wide variety of vinyl monomers such as glycidyl ...

Gupta, Malancha, 1980-

2007-01-01T23:59:59.000Z

465

Capillary waves and the inherent density profile for the liquid-vapor interface  

E-Print Network (OSTI)

. This approach in turn allows: (1) identification of an "outermost layer" of particles on the liquid. (2). is a nonmonotonic function of normal distance through the interface. and is expected to reflect the diverging bulk distribution for the system in a state of liquid-vapor phase coexistence. This leads to identification

Stillinger, Frank

466

Z .Thin Solid Films 392 2001 231 235 Atmospheric pressure chemical vapor deposition of  

E-Print Network (OSTI)

of electrochromic tungsten oxide films Roy G. Gordona,U , Sean Barryb , Jeffrey T. Bartona , Randy N.R. Broomhall oxide, WO , is a coloring layer commonly used in electrochromic windows and displays. Successful: Chemical vapor deposition; Tungsten; Oxides; Electrochromism 1. Introduction Tungsten oxide is a key

467

Ionized physical vapor deposition of integrated circuit interconnects* J. Hopwood,a)  

E-Print Network (OSTI)

alloy silicide gate level and several metal-SiO2 interlayer dielectric ILD levels joined together metal layers. By the year 2007 it is predicted that logic circuits will use 6 to 7 interconnected metal physical vapor deposition I-PVD . The technique economically creates a unidirectional flux of metal which

468

Formation of Nickel Silicide from Direct-Liquid-Injection Chemical-Vapor-Deposited Nickel Nitride Films  

E-Print Network (OSTI)

. Published April 28, 2010. Metal silicides such as TiSi2 and CoSi2 have been commonly used as the contactsFormation of Nickel Silicide from Direct-Liquid-Injection Chemical-Vapor-Deposited Nickel Nitride as the intermediate for subsequent conversion into nickel silicide NiSi , which is a key material for source, drain

469

VOLUME 6S, NUMBER 13 PHYSICAL REVIEW LETTERS Very Cold Trapped Atoms in a Vapor Cell  

E-Print Network (OSTI)

VOLUME 6S, NUMBER 13 PHYSICAL REVIEW LETTERS Very Cold Trapped Atoms in a Vapor Cell 24 SEPTEMBER sample of spin-polarized trapped atoms. The technique used dramati- cally simplifies the production of laser-cooled atoms. In this experiment, 1.8x10' neutral cesium atoms were optically captured directly

Monroe, Christopher

470

Sulfur Impregnation on Activated Carbon Fibers through H2S Oxidation for Vapor Phase  

E-Print Network (OSTI)

Sulfur Impregnation on Activated Carbon Fibers through H2S Oxidation for Vapor Phase Mercury: Sulfur was impregnated onto activated carbon fibers ACFs through H2S oxidation catalyzed by the sorbent CE Database subject headings: Activated carbon; Sulfur; Mercury; Hydrogen sulfides; Oxidation

Borguet, Eric

471

Low temperature junction growth using hot-wire chemical vapor deposition  

DOE Patents (OSTI)

A system and a process for forming a semi-conductor device, and solar cells (10) formed thereby. The process includes preparing a substrate (12) for deposition of a junction layer (14); forming the junction layer (14) on the substrate (12) using hot wire chemical vapor deposition; and, finishing the semi-conductor device.

Wang, Qi; Page, Matthew; Iwaniczko, Eugene; Wang, Tihu; Yan, Yanfa

2014-02-04T23:59:59.000Z

472

Vapor Deposition of Ruthenium from an Amidinate Precursor Huazhi Li,a  

E-Print Network (OSTI)

Vapor Deposition of Ruthenium from an Amidinate Precursor Huazhi Li,a Damon B. Farmer,b Roy G School of Engineering and Applied Sciences, Harvard University, Cambridge, Massachusetts 02138, USA October 11, 2007. Thin films of ruthenium have many current and potential appli- cations. They can be used

473

Vapor Deposition of Ruthenium from an Amidinate Precursor Huazhi Li,a  

E-Print Network (OSTI)

Vapor Deposition of Ruthenium from an Amidinate Precursor Huazhi Li,a Damon B. Farmer,b Roy G. Gordon* ,a Youbo Lin,b Joost Vlassakb a Department of Chemistry and Chemical Biology and b School and potential applications. They can be used as electrodes for capacitors, in which their high work function

474

Chemical vapor deposition of W-Si-N and W-B-N  

DOE Patents (OSTI)

A method of depositing a ternary, refractory based thin film on a substrate by chemical vapor deposition employing precursor sources of tungsten comprising WF[sub 6], either silicon or boron, and nitrogen. The result is a W-Si-N or W-B-N thin film useful for diffusion barrier and micromachining applications. 10 figs.

Fleming, J.G.; Roherty-Osmun, E.L.; Smith, P.M.; Custer, J.S.; Jones, R.V.; Nicolet, M.; Madar, R.; Bernard, C.

1999-06-29T23:59:59.000Z

475

Sulfurization of a carbon surface for vapor phase mercury removal II: Sulfur forms and mercury uptake  

E-Print Network (OSTI)

promote the formation of organic sulfur and the presence of H2S during the cooling process increased in the presence of H2S was very effective towards Hg uptake in nitrogen. Corre- lation of mercury uptake capacitySulfurization of a carbon surface for vapor phase mercury removal ­ II: Sulfur forms and mercury

Borguet, Eric

476

Parallel Reacting Flow Calculations for Chemical Vapor Deposition Reactor Design 1  

E-Print Network (OSTI)

National Laboratories Albuquerque, NM 87185­1111 (To be published in Proceedings of the International at the synthesis of two important research areas: 3D flow and transport modeling of reactors and the simulationParallel Reacting Flow Calculations for Chemical Vapor Deposition Reactor Design 1 Andrew G

Devine, Karen

477

Interannual Variations of Stratospheric Water Vapor in MLS Observations and Climate Model Simulations  

Science Journals Connector (OSTI)

By analyzing the almost-decade-long record of water vapor measurements from the Microwave Limb Sounder (MLS) instrument on the NASA Aura satellite and by detailed diagnostic analysis of the results from state-of-the art climate model simulations, ...

Yoshio Kawatani; Jae N. Lee; Kevin Hamilton

2014-11-01T23:59:59.000Z

478

Evolution of Light-Induced Vapor Generation at a Liquid-Immersed Metallic Nanoparticle  

E-Print Network (OSTI)

Evolution of Light-Induced Vapor Generation at a Liquid-Immersed Metallic Nanoparticle Zheyu Fang nanoparticle in a liquid medium is illuminated with resonant light of sufficient intensity, a nanometer scale- known process of liquid boiling, occurring at a single nanoparticle nucleation site, resulting from

Polman, Albert

479

Chemical Vapor Deposition-Derived Graphene with Electrical Performance of Exfoliated Graphene  

E-Print Network (OSTI)

Chemical Vapor Deposition-Derived Graphene with Electrical Performance of Exfoliated Graphene a scalable method to produce large-area graphene, CVD-grown graphene has heretofore exhibited inferior of CVD-grown graphene in which two important sources of disorder, namely grain boundaries and processing

Hone, James

480

Compensator Control For Chemical Vapor Deposition Film Growth Using Reduced Order Design Models  

E-Print Network (OSTI)

in a high pressure chemical vapor deposition (HPCVD) reactor that in­ cludes multiple species and controls optoelectronic integrated circuits. This can sometimes be addressed, in part, through open­loop optimization [7 reactor with real­time sensing and control as an innovative feature of this proto­ type reactor. Previous

Note: This page contains sample records for the topic "g-band vapor radiometer" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Chlorination of dibenzofuran and dibenzo-p-dioxin vapor by copper (II) chloride  

E-Print Network (OSTI)

Chlorination of dibenzofuran and dibenzo-p-dioxin vapor by copper (II) chloride Jae-Yong Ryu, James limited in- vestigation of dibenzo-p-dioxin (DD) chlorination by CuCl2 to form chlorinated DD (CDD 2003 Elsevier Science Ltd. All rights reserved. Keywords: Dibenzofuran; Dibenzo-p-dioxin; CDF; CDD

Mulholland, James A.

482

Control of Vapor Dispersion and Pool Fire of Liquefied Natural Gas (LNG) with Expansion Foam  

E-Print Network (OSTI)

Liquefied Natural Gas (LNG) is flammable when it forms a 5 – 15 percent volumetric concentration mixture with air at atmospheric conditions. When the LNG vapor comes in contact with an ignition source, it may result in fire and/or explosion. Because...

Yun, Geun Woong

2011-10-21T23:59:59.000Z

483

Time-to-Detect Trends in Precipitable Water Vapor with Varying Measurement Error  

Science Journals Connector (OSTI)

This study determined the theoretical time-to-detect (TTD) global climate model (GCM) precipitable water vapor (PWV) 100-yr trends when realistic measurement errors are considered. Global trends ranged from 0.055 to 0.072 mm yr?1 and varied ...

Jacola Roman; Robert Knuteson; Steve Ackerman

2014-11-01T23:59:59.000Z

484

Progress Toward Meeting NIF Specifications for Vapor Deposited Polyimide Ablator Coatings  

SciTech Connect

We are developing an evaporative coating technique for deposition of thick polyimide (PI) ablator layers on ICF targets. The PI coating technique utilizes stoichiometrically controlled fluxes from two Knudsen cell evaporators containing a dianhydride and a diamine to deposit a polyamic acid (PAA) coating. Heating the PAA coating to 300 deg. C converts the PAA coating to a polyimide. Coated shells are rough due to particles on the substrate mandrels and from damage to the coating caused by the agitation used to achieve a uniform coating. We have developed a smoothing process that exposes an initially rough PAA coated shell to solvent vapor using gas levitation. We found that after smoothing the coatings developed a number of wide (low-mode) defects. We have identified two major contributors to low-mode roughness: surface hydrolysis, and deformation during drying/curing. By minimizing air exposure prior to vapor smoothing, avoiding excess solvent sorption during vapor smoothing, and using slow drying we are able to deposit and vapor smooth coatings 160 {mu}m thick with a surface roughness less than 20 nm RMS.

Letts, Stephan A.; Anthamatten, Mitchell; Buckley, Steven R.; Fearon, Evelyn; Nissen, April E.H.; Cook, Robert C. [Lawrence Livermore National Laboratory (United States)

2004-03-15T23:59:59.000Z

485

Vapor-condensed phase processes in the early solar system Lawrence GROSSMAN*  

E-Print Network (OSTI)

Vapor-condensed phase processes in the early solar system Lawrence GROSSMAN* Department accepted 26 September 2009) Abstract­Equilibrium thermodynamic calculations of the sequence of condensation of condensation, and some may be pristine condensates that escaped later melting. Compact Type A and Type B

Grossman, Lawrence

486

VAPOR-CONDENSED PHASE PROCESSES IN THE EARLY SOLAR SYSTEM. L. Grossman. Department of the  

E-Print Network (OSTI)

VAPOR-CONDENSED PHASE PROCESSES IN THE EARLY SOLAR SYSTEM. L. Grossman. Department@uchicago.edu. Equilibrium thermodynamic calculations of the sequence of condensation of phases from a cooling gas of solar that they underwent melting after condensation, crystallizing into the same phase as- semblage as their precursors

Grossman, Lawrence

487

Sensitive and selective detection of hydrocarbon/water vapor mixtures with a nanoporous silicon microcantilever  

Science Journals Connector (OSTI)

Abstract We have developed a sensitive and selective sensor for hydrocarbon/water vapor mixtures using nanomechanical infrared (IR) spectroscopy with a porous silicon (P-Si) microcantilever. Facile and direct anodization process is utilized to fabricate vertically aligned nanopores of 20–50 nm diameters on a plain silicon microcantilever. The effective Young's modulus and surface area of a P-Si microcantilever can be easily controlled by the thickness of the anodized P-Si layer. Here we demonstrate the detection of 1 wt% naphtha/water vapor mixtures using nanoporous cantilever IR spectroscopy. Nanoporous nature of the cantilever surface enhances its thermomechanical sensitivity. In addition, trapping the volatile hydrocarbon molecules in the nanowells increases the analyte concentration on the surface. Nanomechanical IR spectra of adsorbed vapors were obtained by plotting the deflection amplitudes of the microcantilever as a function of the illuminating IR wavenumber. The mass of the adsorbed vapors was determined from variations in the resonance frequency of the cantilever.

Dongkyu Lee; Omid Zandieh; Seonghwan Kim; Sangmin Jeon; Thomas Thundat

2015-01-01T23:59:59.000Z

488

Structures of nanowires with Zn-ZnO:CuO junctions for detecting ethanol vapors  

Science Journals Connector (OSTI)

The synthesis of ZnO-ZnO:CuO structures in the form of overlapping layers of nanowires of pure and copper oxide-doped zinc oxide is described. These structures are tested as ethanol vapor sensors. The following t...

T. V. Peshkova; D. Ts. Dimitrov; S. S. Nalimova; I. E. Kononova…

2014-05-01T23:59:59.000Z

489

Self-Limiting Chemical Vapor Deposition Growth of Monolayer Graphene from Ethanol  

E-Print Network (OSTI)

carbide,8 to chemical vapor deposition (CVD) of hydrocarbon precursors on transition metals,9-13 economic up to wafer scale,14,15 nickel and copper are the two most commonly used metal substrates. DueC) restricts the growth of graphene to the metal surface.12,17 The uniformity and high quality of the resultant

Maruyama, Shigeo

490

Metalorganic Chemical Vapor Deposition Route to GaN Nanowires with Triangular  

E-Print Network (OSTI)

Metalorganic Chemical Vapor Deposition Route to GaN Nanowires with Triangular Cross Sections Tevye widths of 15-200 nm. Transmission electron microscopy confirmed that the wires were single as a carrier gas, was percolated through the TMG precursor and coupled with a second nitrogen line to give

Yang, Peidong

491

Water Vapor Budget in a Developing Tropical Cyclone and Its Implication for Tropical Cyclone Formation  

Science Journals Connector (OSTI)

Evolution of the water vapor budget from the tropical wave stage to the tropical cyclone stage is examined using a high-resolution numerical model simulation. The focus is on a time window from 27 h prior to genesis to 9 h after genesis, and the ...

Cody Fritz; Zhuo Wang

2014-11-01T23:59:59.000Z

492

X-ray-induced phase transformation in congruent and vapor-transport-equilibrated lithium tantalate  

E-Print Network (OSTI)

X-ray-induced phase transformation in congruent and vapor-transport-equilibrated lithium tantalate an effect of a partially reversible x-ray-induced increase of diffuse x-ray scattering in both congruent been attributed to x-ray-induced decay of the ferroelectric phase at room temperature. The x-ray

Byer, Robert L.

493

Experimental and Modeling Study of the Flammability of Fuel Tank Headspace Vapors from Ethanol/Gasoline Fuels, Phase 2: Evaluations of Field Samples and Laboratory Blends  

SciTech Connect

Study to measure the flammability of gasoline/ethanol fuel vapors at low ambient temperatures and develop a mathematical model to predict temperatures at which flammable vapors were likely to form.

Gardiner, D. P.; Bardon, M. F.; LaViolette, M.

2010-04-01T23:59:59.000Z

494

Vapor Space Corrosion Testing Simulating The Environment Of Hanford Double Shell Tanks  

SciTech Connect

As part of an integrated program to better understand corrosion in the high level waste tanks, Hanford has been investigating corrosion at the liquid/air interface (LAI) and at higher areas in the tank vapor space. This current research evaluated localized corrosion in the vapor space over Hanford double shell tank simulants to assess the impact of ammonia and new minimum nitrite concentration limits, which are part of the broader corrosion chemistry limits. The findings from this study showed that the presence of ammonia gas (550 ppm) in the vapor space is sufficient to reduce corrosion over the short-term (i.e. four months) for a Hanford waste chemistry (SY102 High Nitrate). These findings are in agreement with previous studies at both Hanford and SRS which showed ammonia gas in the vapor space to be inhibitive. The presence of ammonia in electrochemical test solution, however, was insufficient to inhibit against pitting corrosion. The effect of the ammonia appears to be a function of the waste chemistry and may have more significant effects in waste with low nitrite concentrations. Since high levels of ammonia were found beneficial in previous studies, additional testing is recommended to assess the necessary minimum concentration for protection of carbon steel. The new minimum R value of 0.15 was found to be insufficient to prevent pitting corrosion in the vapor space. The pitting that occurred, however, did not progress over the four-month test. Pits appeared to stop growing, which would indicate that pitting might not progress through wall.

Wiersma, B.; Gray, J. R.; Garcia-Diaz, B. L.; Murphy, T. H.; Hicks, K. R.

2014-01-30T23:59:59.000Z

495

Vapor Corrosion Response of Low Carbon Steel Exposed to Simulated High Level Radioactive Waste  

SciTech Connect

A program to resolve the issues associated with potential vapor space corrosion and liquid/air interface corrosion in the Type III high level waste tanks is in place. The objective of the program is to develop understanding of vapor space (VSC) and liquid/air interface (LAIC) corrosion to ensure a defensible technical basis to provide accurate corrosion evaluations with regard to vapor space and liquid/air interface corrosion. The results of the FY05 experiments are presented here. The experiments are an extension of the previous research on the corrosion of tank steel exposed to simple solutions to corrosion of the steel when exposed to complex high level waste simulants. The testing suggested that decanting and the consequent residual species on the tank wall is the predominant source of surface chemistry on the tank wall. The laboratory testing has shown that at the boundary conditions of the chemistry control program for solutions greater than 1M NaNO{sub 3}{sup -}. Minor and isolated pitting is possible within crevices in the vapor space of the tanks that contain stagnant dilute solution for an extended period of time, specifically when residues are left on the tank wall during decanting. Liquid/air interfacial corrosion is possible in dilute stagnant solutions, particularly with high concentrations of chloride. The experimental results indicate that Tank 50 would be most susceptible to the potential for liquid/air interfacial corrosion or vapor space corrosion, with Tank 49 and 41 following, since these tanks are nearest to the chemistry control boundary conditions. The testing continues to show that the combination of well-inhibited solutions and mill-scale sufficiently protect against pitting in the Type III tanks.

Wiersma, B

2006-01-26T23:59:59.000Z

496

Tank 241-B-103 headspace gas and vapor characterization: Results for homogeneity samples collected on October 16, 1996. Tank vapor characterization project  

SciTech Connect

This report presents the results of analyses of samples taken from the headspace of waste storage tank 241-B-103 (Tank B-103) at the Hanford Site in Washington State. Samples were collected to determine the homogeneity of selected inorganic and organic headspace constituents. Two risers (Riser 2 and Riser 7) were sampled at three different elevations (Bottom, Middle, and Top) within the tank. Tank headspace samples were collected by SGN Eurisys Service Corporation (SESC) and were analyzed by Pacific Northwest National Laboratory (PNNL) to determine headspace concentrations of selected non-radioactive analytes. Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL.

Olsen, K.B.; Pool, K.H.; Evans, J.C. [and others

1997-06-01T23:59:59.000Z

497

The Vapor Plume at Material Disposal Are C in Relation to Pajarito Corridor Facilities  

SciTech Connect

A vapor plume made up of volatile organic compounds is present beneath Material Disposal Area C (MDA C) at Los Alamos National Laboratory (LANL). The location and concentrations within the vapor plume are discussed in relation to existing and planned facilities and construction activities along Pajarito Road (the 'Pajarito Corridor') and in terms of worker health and safety. This document provides information that indicates that the vapor plume does not pose a threat to the health of LANL workers nor will it pose a threat to workers during construction of proposed facilities along Pajarito Road. The Los Alamos National Laboratory (LANL or the Laboratory) monitors emissions, effluents, and environmental media to meet environmental compliance requirements, determine actions to protect the environment, and monitor the long-term health of the local environment. LANL also studies and characterizes 'legacy' waste from past Laboratory operations to make informed decisions regarding eventual corrective actions and the disposition of that waste. Starting in 1969, these activities have been annually reported in the LANL Environmental Report (formerly Environmental Surveillance Report), and are detailed in publicly accessible technical reports meeting environmental compliance requirements. Included among the legacy sites being investigated are several formerly used material disposal areas (MDAs) set aside by the Laboratory for the general on-site disposal of waste from mission-related activities. One such area is MDA C located in Technical Area 50 (TA-50), which was used for waste disposal between 1948 and 1974. The location of TA-50 is depicted in Figure 1. The present paper uses a series of maps and cross sections to address the public concerns raised about the vapor plume at MDA C. As illustrated here, extensive sampling and data interpretation indicate that the vapor plume at MDA C does not pose a threat to the health of LANL workers nor will it pose a threat to workers during construction of the proposed facilities and utility trenches. The public cannot be directly exposed to the vapor plume beneath MDA C because Pajarito Road is closed to the public.

Masse, William B. [Los Alamos National Laboratory

2012-04-02T23:59:59.000Z

498

Effect of water vapor/hydrogen environments on niobium, B-66 niobium alloy, tantalum, and Ta-10W alloy  

SciTech Connect

In this paper, the results of an experimental investigation of the effect of water vapor/hydrogen environments on the mechanical properties of niobium, B-66 niobium alloy, tantalum, and Ta-10W alloy are presented. Tensile tests were conducted on specimens of these materials in water vapor/hydrogen mixture ratios of 1 and 3. The water vapor/hydrogen environment caused strength reductions on tantalum and Ta-10W and ductility reductions on all four materials. The degree and causes of embrittlement were a complex function of temperature.

Walter, R.J.; Bentle, G.G.; Chandler, W.T. (Rockwell International Corp., Canoga Park, CA (United States). Rocketdyne Div.)

1991-04-01T23:59:59.000Z

499

ARM - Facility News Article  

NLE Websites -- All DOE Office Websites (Extended Search)

New Microwave Radiometer Makes Water Vapor Measurements in the Arid Cold a New Microwave Radiometer Makes Water Vapor Measurements in the Arid Cold a Snap Bookmark and Share The 183 GHz radiometer, protected inside an insulated enclosure (inset), is installed on the roof of the primary instrument shelter at Barrow. To prevent snow from accumulating on the mylar window, a blower mounted beneath the radiometer directs air through a duct to a standard Y-shaped fitting mounted on top of the radiometer. The 183 GHz radiometer, protected inside an insulated enclosure (inset), is installed on the roof of the primary instrument shelter at Barrow. To prevent snow from accumulating on the mylar window, a blower mounted beneath the radiometer directs air through a duct to a standard Y-shaped fitting mounted on top of the radiometer.

500

Posters Scanning Raman Lidar Measurements of Atmospheric Water Vapor and Aerosols  

NLE Websites -- All DOE Office Websites (Extended Search)

5 5 Posters Scanning Raman Lidar Measurements of Atmospheric Water Vapor and Aerosols R. A. Ferrare and K. D. Evans (a) Hughes STX Corporation Lanham, Maryland S. H. Melfi and D. N. Whiteman NASA/Goddard Space Flight Center Greenbelt, Maryland The principal objective of the Department of Energy's (DOE) Atmospheric Radiation Measurement Program (ARM) is to develop a better understanding of the atmospheric radiative balance in order to improve the parameterization of radiative processes in general circulation models (GCMs) which are used to study climate change. Meeting this objective requires detailed measurements of both water vapor and aerosols since these atmospheric constituents affect the radiation balance directly, through scattering and absorption of solar and