Powered by Deep Web Technologies
Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

From Protein Structure to Function: Ring Cycle for Dilating and  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

From Protein Structure to Function: Ring Cycle for Dilating and Constricting the Nuclear Pore Print From Protein Structure to Function: Ring Cycle for Dilating and Constricting the Nuclear Pore Print Nuclear pore complexes (NPCs) act as the central gatekeepers for selective transport between the cytoplasm and the nucleus. They allow the exchange of selected proteins and ribonucleoproteins, while preventing the transport of material not meant to cross the nuclear envelope. The NPC transport channel is the largest and most complex transport conduit in the eukaryotic kingdom and it is likely composed of only 3 out of 30 nuclear pore complex proteins (nups). Researchers from the Howard Hughes Medical Institute at the Rockefeller University have determined crystal structures of interacting domains of these centrally located channel nups, Nup54, Nup58, and Nup62, using data collected at ALS Beamline 8.2.1. These structures allowed them to elucidate the molecular mechanism that underlies large-scale diameter changes of NPCs and propose a 'ring cycle' for dilating and constricting NPCs from 10-50 nm. The ring cycle would provide a method to adjust transport activities to cellular demands with a rapid response time.

2

From Protein Structure to Function: Ring Cycle for Dilating and  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

From Protein Structure to From Protein Structure to Function: Ring Cycle for Dilating and Constricting the Nuclear Pore From Protein Structure to Function: Ring Cycle for Dilating and Constricting the Nuclear Pore Print Wednesday, 28 August 2013 00:00 Nuclear pore complexes (NPCs) act as the central gatekeepers for selective transport between the cytoplasm and the nucleus. They allow the exchange of selected proteins and ribonucleoproteins, while preventing the transport of material not meant to cross the nuclear envelope. The NPC transport channel is the largest and most complex transport conduit in the eukaryotic kingdom and it is likely composed of only 3 out of 30 nuclear pore complex proteins (nups). Researchers from the Howard Hughes Medical Institute at the Rockefeller University have determined crystal structures of interacting domains of these centrally located channel nups, Nup54, Nup58, and Nup62, using data collected at ALS Beamline 8.2.1. These structures allowed them to elucidate the molecular mechanism that underlies large-scale diameter changes of NPCs and propose a 'ring cycle' for dilating and constricting NPCs from 10-50 nm. The ring cycle would provide a method to adjust transport activities to cellular demands with a rapid response time.

3

From Protein Structure to Function: Ring Cycle for Dilating and  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

From Protein Structure to Function: Ring Cycle for Dilating and Constricting the Nuclear Pore Print From Protein Structure to Function: Ring Cycle for Dilating and Constricting the Nuclear Pore Print Nuclear pore complexes (NPCs) act as the central gatekeepers for selective transport between the cytoplasm and the nucleus. They allow the exchange of selected proteins and ribonucleoproteins, while preventing the transport of material not meant to cross the nuclear envelope. The NPC transport channel is the largest and most complex transport conduit in the eukaryotic kingdom and it is likely composed of only 3 out of 30 nuclear pore complex proteins (nups). Researchers from the Howard Hughes Medical Institute at the Rockefeller University have determined crystal structures of interacting domains of these centrally located channel nups, Nup54, Nup58, and Nup62, using data collected at ALS Beamline 8.2.1. These structures allowed them to elucidate the molecular mechanism that underlies large-scale diameter changes of NPCs and propose a 'ring cycle' for dilating and constricting NPCs from 10-50 nm. The ring cycle would provide a method to adjust transport activities to cellular demands with a rapid response time.

4

Ring Cycle for Dilating and Constricting the Nuclear Pore  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ring Cycle for Dilating and Ring Cycle for Dilating and Constricting the Nuclear Pore Ring Cycle for Dilating and Constricting the Nuclear Pore Print Thursday, 13 June 2013 09:30 Pictured is an illustration of several nuclear pore complexes (NPCs) embedded in a cell nucleus. NPCs act as gatekeepers between a cell's cytoplasm and its nucleus. Based on crystallographic analyses, Sozanne R. Solmaz et al. uncover the molecular mechanism that underlies the large changes in diameter of NPCs and suggest a "ring cycle" mechanism for dilating and constricting the central NPC channel. The model could explain the ability of NPCs to accommodate transport substrates of a large size range and rapidly adjust to cellular transport needs. Read the full article. (Image courtesy of Sozanne R. Solmaz, Günter Blobel, and Ivo Melčák.)

5

A Cycle Augmentation Algorithm for Minimum Cost Multicommodity Flows on a Ring  

E-Print Network [OSTI]

A Cycle Augmentation Algorithm for Minimum Cost Multicommodity Flows on a Ring Bruce Shepherd bshep of Ford and Fulkerson [5]. We mention that a similar state of affairs held for generalized

Shepherd, Bruce

6

Thermoset polymers via ring opening metathesis polymerization of functionalized oils  

DOE Patents [OSTI]

The invention provides a method for producing a thermosetting resin from renewable oils, the method comprising supplying renewable oil molecules containing strained ring alkene moieties; reacting the alkene moieties with cyclic alkenes to create a polymer; and repeating the above two steps until the resin having desired characteristics are obtained. Also provided is a thermoset resin comprising functionalized renewable oil polymerized with a co-monomer.

Larock, Richard C; Henna, Phillip H; Kessier, Michael R

2012-11-27T23:59:59.000Z

7

Investigations into the Structure and Function of the Escherichia coli FtsZ-Ring  

E-Print Network [OSTI]

Investigations into the Structure and Function of the Escherichia coli FtsZ-Ring by Jesse Stricker into the Structure and Function of the Escherichia coli FtsZ-Ring by Jesse Stricker Department of Cell Biology Duke

Erickson, Harold P.

8

Tracing dust provenance, cycling, and history in the Wasatch Mountains using strontium isotopes and tree rings.  

E-Print Network [OSTI]

??To further our understanding of dust cycling from the Great Basin to the Rocky Mountains, this study uses strontium concentrations and isotopes (87Sr/86Sr) to investigate (more)

Miller, Olivia Leigh

2013-01-01T23:59:59.000Z

9

RANKIN-SELBERG L-FUNCTIONS AND CYCLES ON UNITARY SHIMURA VARIETIES  

E-Print Network [OSTI]

RANKIN-SELBERG L-FUNCTIONS AND CYCLES ON UNITARY SHIMURA VARIETIES BENJAMIN HOWARD Contents 1 #12;RANKIN-SELBERG L-FUNCTIONS AND CYCLES ON UNITARY SHIMURA VARIETIES 3 defined by x (iC()x, i. Introduction 1 2. Unitary Shimura varieties and their special cycles 2 2.1. Unitary Shimura varieties 2 2

Goren, Eyal Z.

10

RANKIN-SELBERG L-FUNCTIONS AND CYCLES ON UNITARY SHIMURA VARIETIES  

E-Print Network [OSTI]

RANKIN-SELBERG L-FUNCTIONS AND CYCLES ON UNITARY SHIMURA VARIETIES BENJAMIN HOWARD Contents 1. Introduction 1 1.1. Acknowledgements 2 2. Unitary Shimura varieties and their special cycles 2 2.1. Unitary.2. Divisors associated with harmonic forms 18 3.3. Construction of Green functions 18 3.4. Rankin-Selberg L

Howard, Ben

11

Cell Cycle . Author manuscript Role of the protein kinase Kin1 and nuclear centering in actomyosin ring  

E-Print Network [OSTI]

. The ,pom1 tea1 and mutants are defective in restricting Mid1 as a band around the nucleus and misplace, divides through the use of a contractile actomyosin ring (CAR). After spindle breakdown, cell division occurs by theS. pombe constriction of the CAR at the geometric cell centre. A glucan-based septal

Boyer, Edmond

12

Discovering functional transcription-factor combinations in the human cell cycle  

E-Print Network [OSTI]

Discovering functional transcription-factor combinations in the human cell cycle Zhou Zhu,1 Jay-factor (TF) combinations using phylogenetically conserved sequences and microarray-based expression data of binding sites in the vicinity of one another and whether these combinations result in more coherent

Church, George M.

13

Neonatal Pulmonary Hypertension Urea-Cycle Intermediates, Nitric Oxide Production, and Carbamoyl-Phosphate Synthetase Function  

Science Journals Connector (OSTI)

...mutation (unpublished data). We speculate that persons with the AA genotype may have an advantage in terms of urea-cycle function and interrelated metabolic processes, especially under conditions of environmental stress. Although the functional status of carbamoyl-phosphate synthetase appears to affect... Failure of the transition to a cardiorespiratory circulation at birth results in persistent pulmonary hypertension of the newborn. Characterized by elevated pulmonary vascular resistance with extrapulmonary right-to-left shunting of blood across the ...

Pearson D.L.; Dawling S.; Walsh W.F.

2001-06-14T23:59:59.000Z

14

Spin-polarization and spin-dependent logic gates in a double quantum ring based on Rashba spin-orbit effect: Non-equilibrium Green's function approach  

SciTech Connect (OSTI)

Spin-dependent electron transport in an open double quantum ring, when each ring is made up of four quantum dots and threaded by a magnetic flux, is studied. Two independent and tunable gate voltages are applied to induce Rashba spin-orbit effect in the quantum rings. Using non-equilibrium Green's function formalism, we study the effects of electron-electron interaction on spin-dependent electron transport and show that although the electron-electron interaction induces an energy gap, it has no considerable effect when the bias voltage is sufficiently high. We also show that the double quantum ring can operate as a spin-filter for both spin up and spin down electrons. The spin-polarization of transmitted electrons can be tuned from ?1 (pure spin-down current) to +1 (pure spin-up current) by changing the magnetic flux and/or the gates voltage. Also, the double quantum ring can act as AND and NOR gates when the system parameters such as Rashba coefficient are properly adjusted.

Eslami, Leila, E-mail: Leslami@iust.ac.ir; Esmaeilzadeh, Mahdi, E-mail: mahdi@iust.ac.ir [Department of Physics, Iran University of Science and Technology, Tehran 16846 (Iran, Islamic Republic of)

2014-02-28T23:59:59.000Z

15

Expansion-contraction cycles for cement optimized as a function of additives  

SciTech Connect (OSTI)

An experimental study was carried out to investigate the addition of specific additives to cement in order to eliminate the micro-fractures and micro-annuli that cause gas migration. The experiments performed monitored the change in the cement slurry pressure during the setting of the cement. During the setting period of the cement, two time cycles of cement expansion and contraction were observed. This is due to the individual contributions of each part of the cement mixture. To obtain the optimum tightness of the cement, final optimum concentrations of the additives were obtained experimentally, where the cyclic pressure behavior of the cement was optimized for the best final cement results. By utilizing the correct amount of Anchorage Clay, XC-Polymer, Ironite Scavenger, Ultrafine cement and Synthetic Rubber powder in a class G mixture at a given temperature and confining pressure, an impermeable cement mixture can be obtained. The correct amount of Synthetic Rubber used for cyclic pressure reduction is a function of cement setting temperature and pressure as well as the elastic properties of the rubber. By using laboratory testing at different pressure and temperature with different rubber concentrations and elastic properties, it is estimated that the entire annulus can have an impermeable cement from surface to total depth. The difference in temperature and pressure with depth dictates the concentration and elastic properties of the rubber as the required expansion and contraction changes with depth.

Talabani, S.; Hareland, G. [New Mexico Inst. of Mining and Technology, Socorro, NM (United States)

1995-12-31T23:59:59.000Z

16

Viscosity of Ring Polymer Melts  

Science Journals Connector (OSTI)

Viscosity of Ring Polymer Melts ... The ratio of the zero-shear viscosities of linear polymer melts ?0,linear to their ring counterparts ?0,ring at isofrictional conditions is discussed as a function of the number of entanglements Z. ... For this reason we have determined the viscosities by fitting the complex viscosity curves with different methods to obtain reliable estimates and error bars (see Supporting Information). ...

Rossana Pasquino; Thodoris C. Vasilakopoulos; Youn Cheol Jeong; Hyojoon Lee; Simon Rogers; George Sakellariou; Jrgen Allgaier; Atsushi Takano; Ana R. Brs; Taihyun Chang; Sebastian Gooen; Wim Pyckhout-Hintzen; Andreas Wischnewski; Nikos Hadjichristidis; Dieter Richter; Michael Rubinstein; Dimitris Vlassopoulos

2013-09-17T23:59:59.000Z

17

Li-Ion polymer cells thermal property changes as a function of cycle-life  

SciTech Connect (OSTI)

The impact of elevated temperature chargeedischarge cycling on thermal conductivity (K-value) of Lithium Ion Polymer (LIP) cells of various chemistries from three different manufacturers was investigated. These included high voltage (Graphite/LiCoO2:3.0e4.35 V), wide voltage (Si:C/LiCoO2:2.7e4.35 V) and conventional (Graphite/LiCoO2:3.0e4.2 V) chemistries. Investigation results show limited variability within the in-plane and through-plane K-values for the fresh cells with graphite-based anodes from all three suppliers. After 500 cycles at 45 C, in-plane and through-plane K-values of the high voltage cells reduced less vs. those for the wide voltage cells. Such results suggest that high temperature cycling could have a greater impact on thermal properties of Si:C cells than on the LIP cells with graphite (Gr) anode cells we tested. This difference is due to the excess swelling of Si:C-anode based cells vs. Gr-anode cells during cycling, especially at elevated temperatures. Thermal modeling is used to evaluate the impact of K-value changes, due to cycles at 45 C, on the cells internal heat propagation under internal short circuit condition that leads to localized meltdown of the separator.

Maleki, Hossein [Motorola Mobility; Wang, Hsin [ORNL; Porter, Wallace D [ORNL; Hallmark, Jerry [Motorola Mobility

2014-01-01T23:59:59.000Z

18

Precooler Ring Vacuum System  

SciTech Connect (OSTI)

The precooler vacuum system, as proposed by FNAL, is based on a suitable modification of the existing Electron Cooling Ring System. Because of the magnetic cycle of the bending magnets, distributed ion pumping, as exists in the Electron Cooling Ring, is not applicable. Instead, the proposed pumping will be done with commercial appendage ion pumps mounted approximately every two meters around the circumference of the ring. The loss of effective pumping speed and non-uniformity of system pressure with appendage pumps may not be major considerations but the large number required does effect experimental and analytical equipment placement considerations. There is a distributed pumping technique available which: (1) is not affected by the magnetic cycle of the bending magnets; (2) will provide a minimum of four times the hydrogen pumping speed of the proposed appendage ion pumps; (3) will require no power during pumping after the strip is activated; (4) will provide the heat source for bakeout; (5) is easily replaceable; and (6) can be purchased, installed, and operated at a generous economic advantage over the presently proposed ion pumped system. The pumping technique referred to is non-evaporable gettering with ST101 Zr/Al pumping strip. A technical description of this pumping strip is given on Data Sheet 1 and 2 attached to this report.

Moenich, J.

1980-10-02T23:59:59.000Z

19

Energies of strained silica rings  

Science Journals Connector (OSTI)

The energies of strained two-member and three-member rings of SiO4 tetrahedra are calculated using models based on continuous SiO2 networks. These rings are considered to form highly reactive ``defect'' centers in vitreous SiO2 and at its surface. The calculations are based on a generalized gradient approximation to density-functional theory, and give strain energies of 1.23 and 0.25 eV for two- and three-member rings, considerably smaller than those previously estimated from Hartree-Fock calculations applied to small hydrogen-terminated molecular models. Structural results are compared with experiment for solids and molecules containing such rings. Changes in bond charge densities due to ring strain are illustrated, and modifications of the electronic states of relaxed SiO2 networks caused by strained ring defects are discussed.

D. R. Hamann

1997-06-01T23:59:59.000Z

20

Optimal vortex rings and aquatic propulsion mechanisms  

Science Journals Connector (OSTI)

...vortex rings and aquatic propulsion mechanisms P. F. Linden...fluid mechanics behind these propulsion mechanisms and show that...over the cycle. 4. FISH PROPULSION BY UNDULATORY SWIMMING Most marine organisms have only discrete...

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Compounds having aromatic rings and side-chain amide-functionality and a method for transporting monovalent anions across biological membranes using the same  

DOE Patents [OSTI]

A compound containing at least two aromatic rings covalently bonded together, with each aromatic ring containing at least one oxyacetamide-based side chain, the compound being capable of forming a chloride ion channel across a lipid bilayer, and transporting chloride ion across the lipid bilayer.

Davis, Jeffery T. (College Park, MD); Sidorov, Vladimir (Richmond, VA); Kotch, Frank W. (New Phila., PA)

2008-04-08T23:59:59.000Z

22

NSLS Booster & Linac Ring  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Booster & Linac Ring Booster & Linac Ring Booster Operating Parameters (pdf) Lattice Information (pdf) Mechanical Drawing (pdf) Standard Operating Mode Electrons are injected into the NSLS storage rings from a 750 MeV booster synchrotron fed by a 120 MeV linac. The electrons are first produced in a 100 KeV triode electron gun. The gun is pulsed at the booster revolution period, 94.6 nsec, seven times per booster cycle. Each pulse is 5 nsec long and supplies about 17 microbunches in the linac. After acceleration in the linac, the beam is injected into the booster on seven successive turns. Multi-turn injection in the booster is accomplished in the following way: The beam is deflected into the booster by a septum magnet. The first linac pulse goes around the booster and returns to the injection point just as

23

The positron accumulator ring for the APS  

SciTech Connect (OSTI)

The Positron Accumulator Ring (PAR) is designed to accumulate and damp positrons from the 450-MeV linac during the 0.5-s cycle time of the injector synchrotron for the APS 7-GeV storage ring. During 0.4 s of each synchrotron cycle, up to 24 linac pulses are injected into the horizontal phase space of the PAR at a 60-Hz rate. Each injected pulse occupies about 1.3 of the circumference of the accumulator ring. After 0.1 s for longitudinal damping, the single accumulated bunch is transferred to one of the 353-MHz buckets of the injector synchrotron RF system. The bunch is accelerated to 7 GeV and transferred to the storage ring, while the PAR accumulates the next bunch of positrons. 2 refs., 3 figs., 2 tabs.

Crosbie, E.A.

1989-01-01T23:59:59.000Z

24

Concentric ring flywheel with hooked ring carbon fiber separator/torque coupler  

DOE Patents [OSTI]

A concentric ring flywheel with expandable separators, which function as torque couplers, between the rings to take up the gap formed between adjacent rings due to differential expansion between different radius rings during rotation of the flywheel. The expandable separators or torque couplers include a hook-like section at an upper end which is positioned over an inner ring and a shelf-like or flange section at a lower end onto which the next adjacent outer ring is positioned. As the concentric rings are rotated the gap formed by the differential expansion there between is partially taken up by the expandable separators or torque couplers to maintain torque and centering attachment of the concentric rings.

Kuklo, Thomas C. (Oakdale, CA)

1999-01-01T23:59:59.000Z

25

Ion Rings for Magnetic Fusion  

SciTech Connect (OSTI)

This Final Technical Report presents the results of the program, Ion Rings for Magnetic Fusion, which was carried out under Department of Energy funding during the period August, 1993 to January, 2005. The central objective of the program was to study the properties of field-reversed configurations formed by ion rings. In order to reach this objective, our experimental program, called the Field-reversed Ion Ring Experiment, FIREX, undertook to develop an efficient, economical technology for the production of field-reversed ion rings. A field-reversed configuration (FRC) in which the azimuthal (field-reversing) current is carried by ions with gyro-radius comparable to the magnetic separatrix radius is called a field-reversed ion ring. A background plasma is required for charge neutralization of the ring, and this plasma will be confined within the ring's closed magnetic flux. Ion rings have long been of interest as the basis of compact magnetic fusion reactors, as the basis for a high-power accelerator for an inertial fusion driver, and for other applications of high power ion beams or plasmas of high energy density. Specifically, the FIREX program was intended to address the longstanding question of the contribution of large-orbit ions to the observed stability of experimental FRCs to the MHD tilt mode. Typical experimental FRCs with s {approx} 2-4, where s is the ratio of separatrix radius to ion gyro-radius, have been stable to tilting, but desired values for a fusion reactor, s > 20, should be unstable. The FIREX ring would consist of a plasma with large s for the background ions, but with s {approx} 1 for the ring ions. By varying the proportions of these two populations, the minimum proportion of large-orbit ions necessary for stability could be determined. The incorporation of large-orbit ions, perhaps by neutral-beam injection, into an FRC has been advanced for the purpose of stabilizing, heating, controlling angular momentum, and aiding the formation of a reactor-scale FRC, and the FIREX program was intended to test the ideas behind this approach. We will describe in this report the technological development path and advances in physics understanding that allowed FIREX to reach a regime in which ion rings were reproducibly created with up to about half the current necessary to produce field reversal. Unfortunately, the experiments were limited to this level by a fundamental, unanticipated aspect of the physics of strong ion rings in plasma. The FIREX ring is a strongly anisotropic, current-carrying population of ions moving faster than the Alfven speed in the background plasma. The rapidly changing ring current excites very large-amplitude Alfven waves in the plasma, and these waves strongly affect the ring, causing rapid energy loss in a way that is not compatible with the success of the ring trapping scenario around which FIREX was designed. The result was that FIREX rings were always very short-lived. We will discuss the implication of these results for possible future use of large-orbit ions in FRCs. In short, it appears that a certain range of the parameters characterizing the ring Alfven mach number and distribution function must be avoided to allow the existence of a long-lived energetic ion component in an FRC. This report will explain why FIREX experimental results cannot be directly scaled to quantitatively predict this range for a particular FRC configuration. This will require accurate, three-dimensional simulations. FIREX results do constitute a very good dataset for validating such a code, and simulations already carried out during this program provide a guide to the important physics involved.

Greenly, John, B.

2005-07-31T23:59:59.000Z

26

Bernstein instability driven by thermal ring distribution  

SciTech Connect (OSTI)

The classic Bernstein waves may be intimately related to banded emissions detected in laboratory plasmas, terrestrial, and other planetary magnetospheres. However, the customary discussion of the Bernstein wave is based upon isotropic thermal velocity distribution function. In order to understand how such waves can be excited, one needs an emission mechanism, i.e., an instability. In non-relativistic collision-less plasmas, the only known Bernstein wave instability is that associated with a cold perpendicular velocity ring distribution function. However, cold ring distribution is highly idealized. The present Brief Communication generalizes the cold ring distribution model to include thermal spread, so that the Bernstein-ring instability is described by a more realistic electron distribution function, with which the stabilization by thermal spread associated with the ring distribution is demonstrated. The present findings imply that the excitation of Bernstein waves requires a sufficiently high perpendicular velocity gradient associated with the electron distribution function.

Yoon, Peter H., E-mail: yoonp@umd.edu [Institute for Physical Science and Technology, University of Maryland, College Park, Maryland 20742 (United States); School of Space Research, Kyung Hee University, Yongin-Si, Gyeonggi-Do 446-701 (Korea, Republic of); Hadi, Fazal; Qamar, Anisa [Institute of Physics and Electronics, University of Peshawar, Peshawar 25000 (Pakistan)

2014-07-15T23:59:59.000Z

27

Stirling engine piston ring  

DOE Patents [OSTI]

A piston ring design for a Stirling engine wherein the contact pressure between the piston and the cylinder is maintained at a uniform level, independent of engine conditions through a balancing of the pressure exerted upon the ring's surface and thereby allowing the contact pressure on the ring to be predetermined through the use of a preloaded expander ring.

Howarth, Roy B. (Clifton Park, NY)

1983-01-01T23:59:59.000Z

28

Magnetism in tunable quantum rings  

Science Journals Connector (OSTI)

We have studied the spin structure of circular four-electron quantum rings using tunable confinement potentials. The calculations were done using the exact diagonalization method. Our results indicate that ringlike systems can have oscillatory flips between ferromagnetic and antiferromagnetic behavior as a function of the magnetic field. Furthermore, at constant external magnetic fields there were seen similar oscillatory changes between ferromagnetism and antiferromagnetism when the system parameters were changed. According to our results, the magnetism of quantum rings could be tuned by system parameters.

G. Brdsen; E. Tl; A. Harju

2009-11-10T23:59:59.000Z

29

Bicycling Black Rings  

E-Print Network [OSTI]

We present detailed physics analyses of two different 4+1-dimensional asymptotically flat vacuum black hole solutions with spin in two independent planes: the doubly spinning black ring and the bicycling black ring system ("bi-rings"). The latter is a new solution describing two concentric orthogonal rotating black rings which we construct using the inverse scattering technique. We focus particularly on extremal zero-temperature limits of the solutions. Such limits exist for both types of solutions; for the bi-rings it is obtained when the two rings drag each other to extremality through the effect of gravitational frame-dragging. We construct the phase diagram of currently known zero-temperature vacuum black hole solutions with a single event horizon, and discuss the non-uniqueness introduced by more exotic black hole configurations such as bi-rings and multi-ring saturns.

Elvang, Henriette

2008-01-01T23:59:59.000Z

30

Bicycling Black Rings  

E-Print Network [OSTI]

We present detailed physics analyses of two different 4+1-dimensional asymptotically flat vacuum black hole solutions with spin in two independent planes: the doubly spinning black ring and the bicycling black ring system ("bi-rings"). The latter is a new solution describing two concentric orthogonal rotating black rings which we construct using the inverse scattering technique. We focus particularly on extremal zero-temperature limits of the solutions. We construct the phase diagram of currently known zero-temperature vacuum black hole solutions with a single event horizon, and discuss the non-uniqueness introduced by more exotic black hole configurations such as bi-rings and multi-ring saturns.

Henriette Elvang; Maria J. Rodriguez

2008-01-25T23:59:59.000Z

31

Exergy Analysis of Stirling Cycle Cryogenerator  

Science Journals Connector (OSTI)

Exergy or the available work energy function is ... various systems. This paper attempts to present exergy analysis for Stirling cycle cryogenerator. The cycle...

K. G. Narayankhedkar

1998-01-01T23:59:59.000Z

32

The Fermilab recycler ring  

SciTech Connect (OSTI)

The Fermilab Recycler is a permanent magnet storage ring for the accumulation of antiprotons from the Antiproton Source, and the recovery and cooling of the antiprotons remaining at the end of a Tevatron store. It is an integral part of the Fermilab III luminosity upgrade. The following paper describes the design features, operational and commissioning status of the Recycler Ring.

Martin Hu

2001-07-24T23:59:59.000Z

33

Functional Profiling: From Microarrays via Cell-Based Assays to Novel Tumor Relevant Modulators of the Cell Cycle  

Science Journals Connector (OSTI)

...described by Fukazawa et al. (20). Results and Discussion Assay automation. We designed a functional profiling strategy that took genes...in the web supplement ( http://www.dkfz.de/mga/home/fctassay/sphase ). Scatterplots similar to and including...

Dorit Arlt; Wolfgang Huber; Urban Liebel; Christian Schmidt; Meher Majety; Mamatha Sauermann; Heiko Rosenfelder; Stephanie Bechtel; Alexander Mehrle; Detlev Bannasch; Ingo Schupp; Markus Seiler; Jeremy C. Simpson; Florian Hahne; Petra Moosmayer; Markus Ruschhaupt; Birgit Guilleaume; Ruth Wellenreuther; Rainer Pepperkok; Holger Sltmann; Annemarie Poustka; and Stefan Wiemann

2005-09-01T23:59:59.000Z

34

Factors affecting piston ring friction  

E-Print Network [OSTI]

The piston ring pack friction is a major contributor to the internal combustion engine mechanical friction loss. The oil control ring decides the oil supply to the top two rings in addition to being the major friction ...

Liao, Kai, Ph. D. Massachusetts Institute of Technology

2013-01-01T23:59:59.000Z

35

Study of ring and ring-disk electrodes  

SciTech Connect (OSTI)

Rotating ring and ring-disk electrodes were modeled. The primary, secondary, and below-the-limiting current distributions for ring electrodes were computed. The ring-disk system was modeled for secondary and below-the-limiting current distributions. Mass transfer measurements in laminar, transition, and turbulent flows were made for thin rotating rings. The effect of cell walls on the potential distribution of disk electrodes was computed.

Pierini, P.E.

1981-05-01T23:59:59.000Z

36

Free-energy minima for helium in a ring  

Science Journals Connector (OSTI)

Bloch has suggested that minima in the free energy as a function of angular momentum are responsible for the superfluidity of He4 in a ring. It is shown in this paper that at finite temperatures, the critical velocity is much too small, and hence minima in the free energy are not the cause of superfluidity in a ring.

F. A. Blood; Jr.

1974-08-01T23:59:59.000Z

37

NSLS VUV Storage Ring  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

VUV Storage Ring VUV Storage Ring VUV Normal Operations Operating Parameters (pdf) Insertion Devices Flux & Brightness Orbit Stability Lattice Information (pdf) Lattice : MAD Dataset Mechanical Drawing (pdf) VUV Operating Schedule Introduction & History The VUV Ring at the National Synchrotron Light Source was one of the first of the 2nd generation light sources to operate in the world. Initially designed in 1976 the final lattice design was completed in 1978 shortly after funding was approved. Construction started at the beginning of FY 1979 and installation of the magnets was well underway by the end of FY 1980. The first stored beam was achieved in December of 1981 at 600 MeV and the first photons were delivered to beamlines in May 1982, with routine beam line operations underway by the start of FY 1983. The number of beam

38

Storage Ring Operation Modes  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Longitudinal bunch profile and Up: APS Storage Ring Parameters Longitudinal bunch profile and Up: APS Storage Ring Parameters Previous: Source Parameter Table Storage Ring Operation Modes Standard Operating Mode, top-up Fill pattern: 102 mA in 24 singlets (single bunches) with a nominal current of 4.25 mA and a spacing of 153 nanoseconds between singlets. Lattice configuration: Low emittance lattice with effective emittance of 3.1 nm-rad and coupling of 1%. Bunch length (rms): 33.5 ps. Refill schedule: Continuous top-up with single injection pulses occurring at a minimum of two minute intervals, or a multiple of two minute intervals. Special Operating Mode - 324 bunches, non top-up Fill pattern: 102 mA in 324 uniformly spaced singlets with a nominal single bunch current of 0.31 mA and a spacing of 11.37 nanoseconds between singlets.

39

A study of the microstrip ring resonator and its applications  

E-Print Network [OSTI]

(Continued) CHAPTER F. Effects of the Package Parasitics on the Resonant Frequency G. Experimental Results H. Double Varactor Ring Resonator Page 76 83 88 V PIN DIODES IN A RING RESONATOR AS A SWITCH/FILTER 92 A, PIN Diode Equivalent Circuit B... function of gap sise for the ring resonator in Fig. 19 and Fig. 21. . A varactor tuned ring resonator. C-V traces for the (a) forward and (b) reverse biased varactor diode. . Diagram of a varactor package cross-section. Equivalent circuit of a...

Martin, Tracy Scott

2012-06-07T23:59:59.000Z

40

Localisation in Enveloping Rings  

Science Journals Connector (OSTI)

......right ideal E of R, 3 an n such that (1) If R is commutative this condition becomes, 3n such that (2) where K(I) = (x\\xcel for some ce#). We say that an ideal / of a ring R has the AR property if, for any right ideal E of R, 3n such that E n......

J. C. McConnell

1968-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Tune measurement in the APS ring  

SciTech Connect (OSTI)

The APS system will contain three rings. The first is a positron accumulator ring (PAR). Its function is to coalesce 24, 30-ns-long positron bunches into one 290-ps bunch. The second is the injector synchrotron (IS). It accelerates the 450-MeV positron bunches to 7 Gev for injection into the storage ring (SR). Betatron and synchrotron motion frequently occurs in circular machines, without any deliberate excitation. However, the amplitudes of this motion cannot be predicted. Therefore, it is desirable to have controlled ways to excite these modes. Two types of devices will be used to excite the beam. One will be a magnetic kicker or bumper. All rings already have these devices planned for the horizontal direction for injecting and extracting beams. Some of these magnets will be used for exiting horizontal betatron motion. In the storage ring, a special kicker will be installed to produce up to 1 mm amplitude motion in the vertical direction. Two 8.4-in striplines (SL) (1/4 wavelength at 352 MHz) will be installed on all rings. One stripline in each ring will be used to drive all three tunes, and the other stripline will be used as a pickup. In the PAR and IS, the pickup stripline will be in a dispersive region. This will allow observation of both betatron and synchrotron motions. In the SR, the stripline will be in a nondispersive region because it is not practical to install it in a dispersive region. To do synchrotron tune measurements in the SR, one of the button BPMs located in a dispersive region will be used. To minimize development effort, as much of the BPM system electronics as possible will be used in the tune measurement system. The BPM electronics uses the AMP/PM conversion technique. This system operates at 352 MHz. Thus, tune measurement components were also designed to operate at 352 MHz.

Sellyey, W.; Kahana, E.; Wang, X.

1993-07-01T23:59:59.000Z

42

Accelerated ring laser  

Science Journals Connector (OSTI)

The behavior of a ring laser rotating with nonuniform angular velocity has become of interest, both experimental and theoretical. Within a framework of modest idealizations, we present a classical, relativistically exact theoretical analysis. The beat frequency, we find, is given by an expression of the Sagnac form but with the instantaneous angular velocity in place of the usual constant velocity. One has an "instantaneous Sagnac effect."

Takamasa Takahashi and Ralph Baierlein

1977-02-01T23:59:59.000Z

43

Conformational free energy of melts of ring-linear polymer blends  

Science Journals Connector (OSTI)

The conformational free energy of ring polymers in a blend of ring and linear polymers is investigated using the bond-fluctuation model. Previously established scaling relationships for the free energy of a ring polymer are shown to be valid only in the mean-field sense, and alternative functional forms are investigated. It is shown that it may be difficult to accurately express the total free energy of a ring polymer by a simple scaling argument, or in closed form.

Gopinath Subramanian and Sachin Shanbhag

2009-10-21T23:59:59.000Z

44

Patrick Ring | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Patrick Ring Patrick Ring About Us Patrick Ring - Team Leader, Benefits Continuity Team Patrick Ring is the team leader for the continuity of contractor pension and postretirement benefit programs for contractor workers formerly employed at DOE closure sites. Mr. Ring has more than 31 years of federal service between the U.S. Department of Energy (DOE), U.S. Department of Defense, and the Pension Benefit Guaranty Corporation. His experience has provided him extensive knowledge and experience in dealing with contractor retirement benefit programs. Mr. Ring joined the Office of Legacy Management (LM) in October 2005 as a contractor industrial relations specialist/actuary and a member of the Benefits Continuity Team. Prior to joining LM, Mr. Ring was employed as an actuary with the Defense

45

E-Print Network 3.0 - accumulator ring vacuum Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

ring 3, 4. ELECTRON GENERATION We classify electron production... house turbo pumps to function at a vacuum pressure ... Source: Furman, Miguel - Center for Beam Physics,...

46

Ring Ring. Who's There? A Wind Expert | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Ring Ring. Who's There? A Wind Expert Ring Ring. Who's There? A Wind Expert Ring Ring. Who's There? A Wind Expert August 23, 2010 - 10:44am Addthis Stephen Graff Former Writer & editor for Energy Empowers, EERE Have a question about wind energy? You're not alone. In 2009, about 1,200 people- ranging from farmers, teachers, county commissioners, developers and green job hopefuls -called or emailed Minnesota-based Windustry's wind hotline to learn more about the renewable energy. "The questions are all over the map," said David Tidball, who has been fielding calls since early 2009. "It's everything from, 'What's a wind turbine look like?' to 'How do I get involved in a wind project of my own?'" Windustry's mission is to provide accurate, unbiased and accessible information to the public about wind energy and help people across the

47

Sediment resuspension and erosion by vortex rings  

Science Journals Connector (OSTI)

Particle resuspension and erosion induced by a vortex ringinteracting with a sediment layer was investigated experimentally using flow visualization (particle image velocimetry) high-speed video and a recently developed light attenuation method for measuring displacements in bed level. Near-spherical sediment particles were used throughout with relative densities of 1.27 and diameters ( d ) ranging between 90 and 1600 ? ? m . Attention was focused on initially smooth horizontal bedforms with the vortex ring aligned to approach the bed vertically. Interaction characteristics were investigated in terms of the dimensionless Shields parameter defined using the vortex-ring propagation speed. The critical conditions for resuspension (whereby particles are only just resuspended) were determined as a function of particle Reynolds number (based on the particle settling velocity and d ). The effects of viscous damping were found to be significant for d / ? resuspension volumes are analyzed as a function interaction time impact condition and sediment size.

R. J. Munro; N. Bethke; S. B. Dalziel

2009-01-01T23:59:59.000Z

48

Cycle cover with short cycles Nicole Immorlica  

E-Print Network [OSTI]

Introduction Given a graph and a subset of marked elements (nodes, edges, or some combination thereof), a cycleCycle cover with short cycles Nicole Immorlica£ Mohammad Mahdian£ Vahab S. Mirrokni£ Abstract Cycle for variants of cycle covering problems which bound the size and/or length of the covering cycles

Immorlica, Nicole

49

Ground Movement in SSRL Ring  

SciTech Connect (OSTI)

Users of the Stanford Synchrotron Radiation Lightsource (SSRL) are being affected by diurnal motion of the synchrotron's storage ring, which undergoes structural changes due to outdoor temperature fluctuations. In order to minimize the effects of diurnal temperature fluctuations, especially on the vertical motion of the ring floor, scientists at SSRL tried three approaches: painting the storage ring white, covering the asphalt in the middle of the ring with highly reflective Mylar and installing Mylar on a portion of the ring roof and walls. Vertical motion in the storage ring is measured by a Hydrostatic Leveling System (HLS), which calculates the relative height of water in a pipe that extends around the ring. The 24-hr amplitude of the floor motion was determined using spectral analysis of HLS data, and the ratio of this amplitude before and after each experiment was used to quantitatively determine the efficacy of each approach. The results of this analysis showed that the Mylar did not have any significant effect on floor motion, although the whitewash project did yield a reduction in overall HLS variation of 15 percent. However, further analysis showed that the reduction can largely be attributed to a few local changes rather than an overall reduction in floor motion around the ring. Future work will consist of identifying and selectively insulating these local regions in order to find the driving force behind diurnal floor motion in the storage ring.

Sunikumar, Nikita; /UCLA /SLAC

2011-08-25T23:59:59.000Z

50

Split ring containment attachment device  

DOE Patents [OSTI]

A containment attachment device 10 for operatively connecting a glovebag 200 to plastic sheeting 100 covering hazardous material. The device 10 includes an inner split ring member 20 connected on one end 22 to a middle ring member 30 wherein the free end 21 of the split ring member 20 is inserted through a slit 101 in the plastic sheeting 100 to captively engage a generally circular portion of the plastic sheeting 100. A collar potion 41 having an outer ring portion 42 is provided with fastening means 51 for securing the device 10 together wherein the glovebag 200 is operatively connected to the collar portion 41.

Sammel, Alfred G. (Pittsburgh, PA)

1996-01-01T23:59:59.000Z

51

PROGRESS IN DESIGNING A MUON COOLING RING WITH LITHIUM LENSES.  

SciTech Connect (OSTI)

We discuss particle tracking simulations in a storage ring with lithium lens inserts designed for the six-dimensional phase space cooling of muons by the ionization cooling. The ring design contains one or more lithium lens absorbers for transverse cooling that transmit the beam with very small beta-function values, in addition to liquid-hydrogen wedge-shaped absorbers in dispersive locations for longitudinal cooling. Such a ring could comprise the final component of a cooling system for use in a muon collider. The beam matching between dipole-quadrupole lattices and the lithium lenses is of particular interest.

FUKUI,Y.CLINE,D.B.GARREN,A.A.KIRK,H.G.

2004-03-03T23:59:59.000Z

52

Semigroups and ring endomorphisms  

E-Print Network [OSTI]

. Consequently, Im A consists of only the 0 element of R which means that A is the zero map of R. Since this con- tradicts the hypothesis, we conclude that B is not one to one. ~Pttf 1. 2. zf A d B d phd f * r g R such that BB = A or BA = A then Ker B... contradicts the hypothesis. Thus Ker B/ImB ~ft ttd I I . . If B I ~ ** 1 Id ttty d PB- ism of a ring R such that BB ~ B then (1) Ker B P Im B (2) B is not one to one (3) B fixes every element in Im B (4) R is the group direct sum of Im B and Ker B...

McDaniel, Johnnie Carl

2012-06-07T23:59:59.000Z

53

Reversible Seeding in Storage Rings  

SciTech Connect (OSTI)

We propose to generate steady-state microbunching in a storage ring with a reversible seeding scheme. High gain harmonic generation (HGHG) and echo-enabled harmonic generation (EEHG) are two promising methods for microbunching linac electron beams. Because both schemes increase the energy spread of the seeded beam, they cannot drive a coherent radiator turn-by-turn in a storage ring. However, reversing the seeding process following the radiator minimizes the impact on the electron beam and may allow coherent radiation at or near the storage ring repetition rate. In this paper we describe the general idea and outline a proof-of-principle experiment. Electron storage rings can drive high average power light sources, and free-electron lasers (FELs) are now producing coherent light sources of unprecedented peak brightness While there is active research towards high repetition rate FELs (for example, using energy recovery linacs), at present there are still no convenient accelerator-based sources of high repetition rate, coherent radiation. As an alternative avenue, we recently proposed to establish steady-state microbunching (SSMB) in a storage ring. By maintaining steady-state coherent microbunching at one point in the storage ring, the beam generates coherent radiation at or close to the repetition rate of the storage ring. In this paper, we propose a method of generating a microbunched beam in a storage ring by using reversible versions of linac seeding schemes.

Ratner, Daniel; Chao, Alex; /SLAC

2011-12-14T23:59:59.000Z

54

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported by motor proteins. These tiny machines convert the energy gained from hydrolysing ATP into a series of small conformational changes that allow them to literally "walk" along microscopic tracks. Motor proteins (in the kinesin and myosin families) have been extensively studied by x-ray crystallography, but until recently there was little molecular structural information for dyneins, another type of motor protein. A group from the University of California, San Francisco, working at ALS Beamline 8.3.1 has reported the 6-Å-resolution structure of the motor domain of dynein in yeast. It reveals details of the ring-shaped motor as well as a new, unanticipated feature called the buttress that may play an important role in dynein's mechanical cycle.

55

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported by motor proteins. These tiny machines convert the energy gained from hydrolysing ATP into a series of small conformational changes that allow them to literally "walk" along microscopic tracks. Motor proteins (in the kinesin and myosin families) have been extensively studied by x-ray crystallography, but until recently there was little molecular structural information for dyneins, another type of motor protein. A group from the University of California, San Francisco, working at ALS Beamline 8.3.1 has reported the 6-Å-resolution structure of the motor domain of dynein in yeast. It reveals details of the ring-shaped motor as well as a new, unanticipated feature called the buttress that may play an important role in dynein's mechanical cycle.

56

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported by motor proteins. These tiny machines convert the energy gained from hydrolysing ATP into a series of small conformational changes that allow them to literally "walk" along microscopic tracks. Motor proteins (in the kinesin and myosin families) have been extensively studied by x-ray crystallography, but until recently there was little molecular structural information for dyneins, another type of motor protein. A group from the University of California, San Francisco, working at ALS Beamline 8.3.1 has reported the 6-Å-resolution structure of the motor domain of dynein in yeast. It reveals details of the ring-shaped motor as well as a new, unanticipated feature called the buttress that may play an important role in dynein's mechanical cycle.

57

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported by motor proteins. These tiny machines convert the energy gained from hydrolysing ATP into a series of small conformational changes that allow them to literally "walk" along microscopic tracks. Motor proteins (in the kinesin and myosin families) have been extensively studied by x-ray crystallography, but until recently there was little molecular structural information for dyneins, another type of motor protein. A group from the University of California, San Francisco, working at ALS Beamline 8.3.1 has reported the 6-Å-resolution structure of the motor domain of dynein in yeast. It reveals details of the ring-shaped motor as well as a new, unanticipated feature called the buttress that may play an important role in dynein's mechanical cycle.

58

Carbon Cycle  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Carbon Cycle Carbon Cycle Latest Global Carbon Budget Estimates Including CDIAC Estimates Terrestrial Carbon Management Data Sets and Analyses Carbon Dioxide Emissions from Fossil-Fuel Consumption and Cement Manufacture, (2011) Annual Fossil-Fuel CO2 Emissions: Mass of Emissions Gridded by One Degree Latitude by One Degree Longitude (2012) Monthly Fossil-Fuel CO2 Emissions: Mass of Emissions Gridded by One Degree Latitude by One Degree Longitude (2012) Annual Fossil-Fuel CO2 Emissions: Global Stable Carbon Isotopic Signature (2012) Monthly Fossil-Fuel CO2 Emissions: Isomass (δ 13C) of Emissions Gridded by One Degree Latitude by One Degree Longitude (2012) AmeriFlux - Terrestrial Carbon Dioxide, Water Vapor, and Energy Balance Measurements Estimates of Monthly CO2 Emissions and Associated 13C/12C Values

59

Math 603 Problem Set #5 Due Mon., Feb. 28, 2005 1. a) Let V be an affine variety, with ring of functions R. Let W be a Zariski closed  

E-Print Network [OSTI]

]. Justify your assertions. 4. Given a commutative ring R, define the maximal spectrum of R (denoted Max R) to be the set of maximal ideals of R. For each subset E R, let V (E) denote the set {m Max R | E m} Max R. a) Show that Max R has a topology in which the closed sets are precisely the sets V (E). b) Show that V (E

Harbater, David

60

Friction between Ring Polymer Brushes  

E-Print Network [OSTI]

Friction between ring-polymer brushes at melt densities sliding past each other are studied using extensive course-grained molecular dynamics simulations and scaling arguments, and the results are compared to the friction between linear-polymer brushes. We show that for a velocity range spanning over three decades, the frictional forces measured for ring-polymer brushes are half the corresponding friction in case of linear brushes. In the linear-force regime, the weak inter-digitation of two ring brushes compared to linear brushes also leads to a lower number of binary collisions between the monomers of opposing brushes. At high velocities, where the thickness of the inter-digitation layer between two opposing brushes is on the order monomer size regardless of brush topology, stretched segments of ring polymers take a double-stranded conformation. As a result, monomers of the double-stranded segments collide less with the monomers of the opposing ring brush even though a similar number of monomers occupies the inter-digitation layer for ring and linear-brush bilayers. The numerical data obtained from our simulations is consistent with the proposed scaling analysis. Conformation-dependent frictional reduction observed in ring brushes can have important consequences in non-equilibrium bulk systems.

A. Erbas; J. Paturej

2015-01-07T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Advanced regenerative absorption refrigeration cycles  

DOE Patents [OSTI]

Multi-effect regenerative absorption cycles which provide a high coefficient of performance (COP) at relatively high input temperatures. An absorber-coupled double-effect regenerative cycle (ADR cycle) (10) is provided having a single-effect absorption cycle (SEA cycle) (11) as a topping subcycle and a single-effect regenerative absorption cycle (1R cycle) (12) as a bottoming subcycle. The SEA cycle (11) includes a boiler (13), a condenser (21), an expansion device (28), an evaporator (31), and an absorber (40), all operatively connected together. The 1R cycle (12) includes a multistage boiler (48), a multi-stage resorber (51), a multisection regenerator (49) and also uses the condenser (21), expansion device (28) and evaporator (31) of the SEA topping subcycle (11), all operatively connected together. External heat is applied to the SEA boiler (13) for operation up to about 500 degrees F., with most of the high pressure vapor going to the condenser (21) and evaporator (31) being generated by the regenerator (49). The substantially adiabatic and isothermal functioning of the SER subcycle (12) provides a high COP. For higher input temperatures of up to 700 degrees F., another SEA cycle (111) is used as a topping subcycle, with the absorber (140) of the topping subcycle being heat coupled to the boiler (13) of an ADR cycle (10). The 1R cycle (12) itself is an improvement in that all resorber stages (50b-f) have a portion of their output pumped to boiling conduits (71a-f) through the regenerator (49), which conduits are connected to and at the same pressure as the highest pressure stage (48a) of the 1R multistage boiler (48).

Dao, Kim (14 Nace Ave., Piedmont, CA 94611)

1990-01-01T23:59:59.000Z

62

Relativistic Nuclear Energy Density Functionals  

Science Journals Connector (OSTI)

......research-article Articles Relativistic Nuclear Energy Density Functionals Dario Vretenar...196, 2012 137 Relativistic Nuclear Energy Density Functionals Dario Vretenar...and P. Ring 2. Relativistic nuclear energy density functionals Even though......

Dario Vretenar; Tamara Niksic; Peter Ring

2012-10-01T23:59:59.000Z

63

Ring resonant cavities for spectroscopy  

DOE Patents [OSTI]

Ring-shaped resonant cavities for spectroscopy allow a reduction in optical feedback to the light source, and provide information on the interaction of both s- and p-polarized light with samples. A laser light source is locked to a single cavity mode. An intracavity acousto-optic modulator may be used to couple light into the cavity. The cavity geometry is particularly useful for Cavity Ring-Down Spectroscopy (CRDS). 6 figs.

Zare, R.N.; Martin, J.; Paldus, B.A.; Xie, J.

1999-06-15T23:59:59.000Z

64

Butyl rubber O-ring seals: Revision of test procedures for stockpile materials  

SciTech Connect (OSTI)

Extensive testing showed little correlation between test slab and O-ring performance. New procedures, comparable to those used with the traditional test slabs, were defined for hardness, compression set, and tensile property testing on sacrificial O-ring specimens. Changes in target performance values were made as needed and were, in one case, tightened to reflect the O-ring performance data. An additional study was carried out on O-ring and slab performance vs cure cycle and showed little sensitivity of material performance to large changes in curing time. Aging and spectra of certain materials indicated that two sets of test slabs from current vendor were accidently made from EPDM rather than butyl rubber. Random testing found no O-rings made from EPDM. As a result, and additional spectroscope test will be added to the product acceptance procedures to verify the type of rubber compound used.

Domeier, L.A.; Wagter, K.R.

1996-12-01T23:59:59.000Z

65

Double acting stirling engine piston ring  

DOE Patents [OSTI]

A piston ring design for a Stirling engine wherein the contact pressure between the piston and the cylinder is maintained at a uniform level, independent of engine conditions through a balancing of the pressure exerted upon the ring's surface and thereby allowing the contact pressure on the ring to be predetermined through the use of a preloaded expander ring.

Howarth, Roy B. (Clifton Park, NY)

1986-01-01T23:59:59.000Z

66

Quantum Fourier Transform Over Galois Rings  

E-Print Network [OSTI]

Galois rings are regarded as "building blocks" of a finite commutative ring with identity. There have been many papers on classical error correction codes over Galois rings published. As an important warm-up before exploring quantum algorithms and quantum error correction codes over Galois rings, we study the quantum Fourier transform (QFT) over Galois rings and prove it can be efficiently preformed on a quantum computer. The properties of the QFT over Galois rings lead to the quantum algorithm for hidden linear structures over Galois rings.

Yong Zhang

2009-04-16T23:59:59.000Z

67

Rings and convolution algebras  

E-Print Network [OSTI]

convolution al ebra if the follow1ng properties hold: i) For every xcS and feF the function f defined by f(y) = f(xy) is x x an element of F. ii) For every xcS and LcL the funct1on f defined by fL(x) = L( f) is x an element of F. For notat1onal reasons we... introduce a new var1able y into the above equation by defining f (x) = Ly(f(xy)). L 1ii) For every L, Met the linear functional M*L on F defined by M*L(f) = Mx(Ly(f(xy))) 1s an element of L. M*L is called the convolution of M and L. It is easy to ver1fy...

Zeller, Mike

2012-06-07T23:59:59.000Z

68

Cycle Track Lessons Learned  

E-Print Network [OSTI]

Cycle Track Lessons Learned #12;Presentation Overview · Bicycling trends · Cycle track lessons learned · What is a "Cycle track"? · Essential design elements of cycle tracks Separation Width Crossing driveways & low-volume streets Signalized intersections #12;Trend in kilometers cycled per year

Bertini, Robert L.

69

Photovoltaics Life Cycle Analysis  

E-Print Network [OSTI]

Metrics of Life-Cycle Performance Energy Payback Times (EPBT) Greenhouse Gas Emissions (GHG) Toxic Gases #12;6 Life Cycle GHG Emissions ­EuropeLife Cycle GHG Emissions ­Europe Insolation: 1700 kwh/m2-yr 0 10 #12;7 Life Cycle GHG Emissions ­Comparison with Conventional Technologies Life Cycle GHG Emissions

70

Modules over principal ideal rings  

E-Print Network [OSTI]

need to note, however, , the difference between the two types of "union" of a set of submodules N 1 of a module N, The first is the "set-theoretic union" con- sisting of representatives of all the distinct elements to be found in the Ni... ideal R, which cons1sts of the elements of the ring. Consider the subset B of R of all elements of the form ra + na, where r and a are ring ele- ments and n is an integer. If rla + nla, r2a + n2a s B, then la + nla 2 2a la r2a + la 2 = (rl - r2)a...

Vieaux, Jules Bellin

2012-06-07T23:59:59.000Z

71

Cavity-locked ring down spectroscopy  

DOE Patents [OSTI]

Distinct locking and sampling light beams are used in a cavity ring-down spectroscopy (CRDS) system to perform multiple ring-down measurements while the laser and ring-down cavity are continuously locked. The sampling and locking light beams have different frequencies, to ensure that the sampling and locking light are decoupled within the cavity. Preferably, the ring-down cavity is ring-shaped, the sampling light is s-polarized, and the locking light is p-polarized. Transmitted sampling light is used for ring-down measurements, while reflected locking light is used for locking in a Pound-Drever scheme.

Zare, Richard N. (Stanford, CA); Paldus, Barbara A. (Stanford, CA); Harb, Charles C. (Palo Alto, CA); Spence, Thomas (Union City, CA)

2000-01-01T23:59:59.000Z

72

Block copolymer adhesion promoters via ring-opening metathesis polymerization  

DOE Patents [OSTI]

Coupling agents based on functionalized block copolymers for bonding thermoset polymers to solid materials. These are polymers which possess at least two types of functional groups, one which is able to attach to and react with solid surfaces, and another which can react with a thermoset resin, which are incorporated as pendant groups in monomers distributed in blocks (typically two) along the backbone of the chain. The block copolymers in this invention are synthesized by living ring-opening metathesis polymerization.

Kent, Michael S. (12320 Pine Ridge, NE, Albuquerque, NM 87112); Saunders, Randall (13201 Fruit Ave., NE, Albuquerque, NM 87123)

1997-01-01T23:59:59.000Z

73

Offshore Rankine Cycles.  

E-Print Network [OSTI]

?? The title of the thesis - "Offshore Rankine Cycles" - is very general and cover a large range of engineering fields, e.g. thermodynamic cycles (more)

Brandsar, Jo

2012-01-01T23:59:59.000Z

74

The Organic Rankine Cycle  

Science Journals Connector (OSTI)

Chap. 3 is dedicated to Rankine cycles with organic fluids: the so-called organic Rankine cycles (ORC), which in recent years have ... of the use of...

Costante Mario Invernizzi

2013-01-01T23:59:59.000Z

75

Optimization of Air Conditioning Cycling  

E-Print Network [OSTI]

Benchmark Long Cycle .............................................................................................. 95 5.46 System Pressures and Temperatures Valve Part Cycle Vs Benchmark Long Cycle...

Seshadri, Swarooph

2012-10-19T23:59:59.000Z

76

Used Fuel Disposition Campaign Phase I Ring Compression Testing...  

Broader source: Energy.gov (indexed) [DOE]

Phase I Ring Compression Testing of High Burnup Cladding Used Fuel Disposition Campaign Phase I Ring Compression Testing of High Burnup Cladding The purpose of ring compression...

77

Pattern formation in the exciton inner ring  

Science Journals Connector (OSTI)

We report on the two-beam study of indirect excitons in the inner ring in the exciton emission pattern. One laser beam generates the inner ring and a second weaker beam is positioned in the inner ring. The beam positioned in the inner ring is found to locally suppress the exciton emission intensity. We also report on the inner ring fragmentation and formation of multiple rings in the inner ring region. These features are found to originate from a weak spatial modulation of the excitation beam intensity in the inner ring region. The modulation of exciton emission intensity anticorrelates with the modulation of the laser excitation intensity. The three phenomenainner ring fragmentation, formation of multiple rings in the inner ring region, and emission suppression by a weak laser beam in the inner ringhave a common feature: a reduction of exciton emission intensity in the region of enhanced laser excitation. This effect is explained in terms of exciton transport and thermalization.

M. Remeika, A. T. Hammack, S. V. Poltavtsev, L. V. Butov, J. Wilkes, A. L. Ivanov, K. L. Campman, M. Hanson, and A. C. Gossard

2013-09-17T23:59:59.000Z

78

Stabilizer Codes over Frobenius Rings  

E-Print Network [OSTI]

elements so that B = fjxi jx 2 Rg: 20 The addition and multiplication in the ring R will be used to de ne unitary shift and multiplication operators on Cq. Indeed, for each a in R, we de ne a shift operator X(a) : Cq ! Cq by X(a)jxi = jx+ ai for all x...((ajb)) to be the number of indices i such that ai 6= 0 or bi 6= 0. It follows from these de nitions that wt(!cX(a)Z(b)) = swt((ajb)): Let R be a ring with q elements. Let S be a subgroup of Gn. The stabilizer code Fix(S) associated with S is given by Fix(S) = fv 2 Cq...

Nadella, Sushma

2012-07-16T23:59:59.000Z

79

Reflex ring laser amplifier system  

DOE Patents [OSTI]

The invention is a method and apparatus for providing a reflex ring laser system for amplifying an input laser pulse. The invention is particularly useful in laser fusion experiments where efficient production of high-energy and high power laser pulses is required. The invention comprises a large aperture laser amplifier in an unstable ring resonator which includes a combination spatial filter and beam expander having a magnification greater than unity. An input pulse is injected into the resonator, e.g., through an aperture in an input mirror. The injected pulse passes through the amplifier and spatial filter/expander components on each pass around the ring. The unstable resonator is designed to permit only a predetermined number of passes before the amplified pulse exits the resonator. On the first pass through the amplifier, the beam fills only a small central region of the gain medium. On each successive pass, the beam has been expanded to fill the next concentric non-overlapping region of the gain medium.

Summers, M.A.

1983-08-31T23:59:59.000Z

80

Wavelength-tunable optical ring resonators  

DOE Patents [OSTI]

Optical ring resonator devices are disclosed that can be used for optical filtering, modulation or switching, or for use as photodetectors or sensors. These devices can be formed as microdisk ring resonators, or as open-ring resonators with an optical waveguide having a width that varies adiabatically. Electrical and mechanical connections to the open-ring resonators are made near a maximum width of the optical waveguide to minimize losses and thereby provide a high resonator Q. The ring resonators can be tuned using an integral electrical heater, or an integral semiconductor junction.

Watts, Michael R. (Albuquerque, NM); Trotter, Douglas C. (Albuquerque, NM); Young, Ralph W. (Albuquerque, NM); Nielson, Gregory N. (Albuquerque, NM)

2009-11-10T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Rings in central-force network dynamics  

Science Journals Connector (OSTI)

The central-force network dynamics model for glasses is extended to treat networks involving small regular rings of bonds. In particular, band-limit formulas are obtained for an A2X3 glass consisting of regular puckered six-membered A3X3 rings. The special case of planar rings is compared with observations on vitreous B2O3. This continuous random network of "boroxol" rings shows improved agreement with experiment over a model not containing rings. The remaining discrepancies illustrate the need to include noncentral forces in the network dynamics of v-B2O3.

F. L. Galeener and M. F. Thorpe

1983-11-15T23:59:59.000Z

82

Wavelength-tunable optical ring resonators  

DOE Patents [OSTI]

Optical ring resonator devices are disclosed that can be used for optical filtering, modulation or switching, or for use as photodetectors or sensors. These devices can be formed as microdisk ring resonators, or as open-ring resonators with an optical waveguide having a width that varies adiabatically. Electrical and mechanical connections to the open-ring resonators are made near a maximum width of the optical waveguide to minimize losses and thereby provide a high resonator Q. The ring resonators can be tuned using an integral electrical heater, or an integral semiconductor junction.

Watts, Michael R. (Albuquerque, NM); Trotter, Douglas C. (Albuquerque, NM); Young, Ralph W. (Albuquerque, NM); Nielson, Gregory N. (Albuquerque, NM)

2011-07-19T23:59:59.000Z

83

Multiple Rankine topping cycles  

SciTech Connect (OSTI)

The efficiency of a Rankine cycle is primarily determined by the temperatures of heat addition and rejection. However, no working fluid has been identified which will operate in a Rankine cycle over an extremely wide temperature range. Multiple Rankine topping cycles offer a technique for achieving high thermal efficiencies in power plants by allowing the use of several working fluids. This paper gives a history of Rankine topping cycles, presents an analysis for the calculation of the overall efficiency of a three-module multiple Rankine cycle, and presents results from a case study for a sodium-mercury-water cycle.

McWhirter, J.D. [Argonne National Lab., Idaho Falls, ID (United States). Engineering Div.]|[Idaho State Univ., Pocatello, ID (United States). Coll. of Engineering

1995-07-01T23:59:59.000Z

84

MINIMUM EMITTANCE LATTICE FOR SYNCHROTRON RADIATION STORAGE RINGS  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

MINIMUM EMITTANCE LATTICE FOR MINIMUM EMITTANCE LATTICE FOR SYNCHROTRON RADIATION STORAGE RINGS 1. C. Teng ANL/FNAL LS-17 L. Teng March 18, 1985 The natural emittance of an electron beam in a storage ring is given by (see e.g., M. Sands, SLAC 21) (1) where Cq =~~= 3.832 x 10-l3 m 32/3 mc J x partition factor in the bending plane y = total energy in mc 2 uni ts p orbit radius in bending magnets (assumed the same in all magne ts) H yn 2 - + 2ann ' + Bn I 2 ( a, B, Y = betatron functions ) n, n I dispersion functions <> = averaging over bending magnets We shall calculate for each bending magnet, then average over all magnets. 2 A. General Expression for H This can be calculated in a straightforward manner, but we can save a great deal of arithmetic with some preliminary formal analytical

85

Quantifying Carbon Cycle Feedbacks  

Science Journals Connector (OSTI)

Perturbations to the carbon cycle could constitute large feedbacks on future changes in atmospheric CO2 concentration and climate. This paper demonstrates how carbon cycle feedback can be expressed in formally similar ways to climate feedback, ...

J. M. Gregory; C. D. Jones; P. Cadule; P. Friedlingstein

2009-10-01T23:59:59.000Z

86

Edgeworth cycles revisited  

E-Print Network [OSTI]

Some gasoline markets exhibit remarkable price cycles, where price spikes are followed by a series of small price declines: a pattern consistent with a model of Edgeworth cycles described by Maskin and Tirole. We extend ...

Doyle, Joseph J.

87

The combined cycle  

Science Journals Connector (OSTI)

Any combination of at least two cyclic processes converting thermal energy (heat) to work forms a combined cycle. In principle, the potential number of ... number of options reduces to a variety of cycles consi...

R. U. Pitt

1995-01-01T23:59:59.000Z

88

Water Cycle Pilot Study  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

1 Water Cycle Pilot Study To learn more about Earth's water cycle, the U.S. Department of Energy (DOE) has established a multi-laboratory science team representing five DOE...

89

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Rotary Firing in Ring-Shaped Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Wednesday, 28 April 2010 00:00 Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

90

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Rotary Firing in Ring-Shaped Protein Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Wednesday, 28 April 2010 00:00 Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

91

Cooling system for three hook ring segment  

DOE Patents [OSTI]

A triple hook ring segment including forward, midsection and aft mounting hooks for engagement with respective hangers formed on a ring segment carrier for supporting a ring segment panel, and defining a forward high pressure chamber and an aft low pressure chamber on opposing sides of the midsection mounting hook. An isolation plate is provided on the aft side of the midsection mounting hook to form an isolation chamber between the aft low pressure chamber and the ring segment panel. High pressure air is supplied to the forward chamber and flows to the isolation chamber through crossover passages in the midsection hook. The isolation chamber provides convection cooling air to an aft portion of the ring segment panel and enables a reduction of air pressure in the aft low pressure chamber to reduce leakage flow of cooling air from the ring segment.

Campbell, Christian X.; Eng, Darryl; Lee, Ching-Pang; Patat, Harry

2014-08-26T23:59:59.000Z

92

mathematics single cycle  

E-Print Network [OSTI]

47 mathematics education single cycle master's study programme #12;48 single cycle master's study program in Mathematics Education #12;49 single cycle master's study program in Mathematics Education MATHEMATICS EDUCATION The program is in tune with the principles of the Bologna Declaration. · Academic title

?umer, Slobodan

93

Studies on Integrated Management and Technology System of Cycling Logistics  

Science Journals Connector (OSTI)

The frame on integrated management system of cycling logistics is constructed. The content, function, structure, realization process, operation model of the business and technical systems that consist of cycling logistics integrated management are preliminarily ... Keywords: Cycling Logistics, integrated management, technology System, Service System

Huan Zhang; Zhong Cheng; Yi Lu

2008-10-01T23:59:59.000Z

94

Cycle to Cycle Manufacturing Process Control  

E-Print Network [OSTI]

Most manufacturing processes produce parts that can only be correctly measured after the process cycle has been completed. Even if in-process measurement and control is possible, it is often too expensive or complex to ...

Hardt, David E.

95

Rate of Growth of Fungus Rings  

Science Journals Connector (OSTI)

... MR. O. G. S. CRAWFORD'S letter in NATURE of December 26, page 938, concerning the age of fairy rings, seems to warrant a letter ...

J. RAMSBOTTOM

1926-01-30T23:59:59.000Z

96

Status of the SLC damping rings  

SciTech Connect (OSTI)

Electron beams of full design energy 1.21 GeV and nearly full design intensity 4 x 10/sup 10/ particles/pulse (design 5 x 10/sup 10/) have been extracted from the Stanford Linac and successfully stored in the electron damping ring. Beams of less intensity have been extracted from the ring and reinjected into the Linac. The present intensity limits are not thought to be fundamental. The operating experience with the electron ring and the status of the construction of the positron ring will be discussed. 11 refs., 1 fig., 2 tabs.

Hutton, A.M.; Davies-White, W.A.; Delahaye, J.P.; Fieguth, T.H.; Hofmann, A.; Jager, J.; Kloeppel, P.K.; Lee, M.J.; Linebarger, W.A.; Rivkin, L.

1985-06-01T23:59:59.000Z

97

Condenser for illuminating a ring field  

DOE Patents [OSTI]

A series of segments of a parent aspheric mirror having one foci at at a si-point source of radiation and the other foci at the radius of a ring field have all but one or all of their beams translated and rotated by sets of mirrors such that all of the beams pass through the real entrance pupil of a ring field camera about one of the beams and fall onto the ring field radius as a coincident image as an arc of the ring field.

Sweatt, William C. (Albuquerque, NM)

1994-01-01T23:59:59.000Z

98

Condenser for illuminating a ring field  

DOE Patents [OSTI]

A series of segments of a parent aspheric mirror having one foci at a point source of radiation and the other foci at the radius of a ring field have all but one or all of their beams translated and rotated by sets of mirrors such that all of the beams pass through the real entrance pupil of a ring field camera about one of the beams and fall onto the ring field radius as a coincident image as an arc of the ring field. 5 figs.

Sweatt, W.C.

1994-11-01T23:59:59.000Z

99

Steam in the Ring Discharge  

Science Journals Connector (OSTI)

The behaviour of steam and its decomposition products in the ring discharge has been examined. Dry hydrogen is not dissociated. The production of atomic hydrogen is dependent upon the presence of steam which dissociates into hydroxyl and atomic hydrogen. A secondary source of atomic hydrogen is then afforded by the interaction of hydroxyl with molecular hydrogen. The escape from the discharge of atomic hydrogen, a long-lived species, favours the dissociation of steam. Mercury vapour, on the other hand, inhibits the formation of atomic hydrogen and thus leads to a high equilibrium steam concentration. Unlike dry hydrogen, dry oxygen is dissociated into atoms, but these have a short life as such and recombine in the discharge to form molecular oxygen and ozone. The reaction mechanisms occurring in the discharge are discussed in the light of spectrographic results.

G I Finch

1949-01-01T23:59:59.000Z

100

On rings of structural numbers  

E-Print Network [OSTI]

structural numbers over the set X, and let B(X) have the operations defined above with equality also as before. Theorem I. l. If X is any set, then B(X) is a commutative ring with identity. Proof. The structural number 0 is the additive identity element... with identity g. Definition I. 7. If A, B e S(X) then A'B = (P U q ( p e A, q e B, p Il q = &f and p U q can be formed in an odd number of ways). ~E1 t. 4. L t A = (( . b), (bj. 7 )) 4 B = ((b, c), (b), (a)) be in S(X) for some X. Then AD B = {{b, a), {a...

Powell, Wayne Bruce

2012-06-07T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Block copolymer adhesion promoters via ring-opening metathesis polymerization  

DOE Patents [OSTI]

Coupling agents are disclosed based on functionalized block copolymers for bonding thermoset polymers to solid materials. These are polymers which possess at least two types of functional groups, one which is able to attach to and react with solid surfaces, and another which can react with a thermoset resin, which are incorporated as pendant groups in monomers distributed in blocks (typically two) along the backbone of the chain. The block copolymers in this invention are synthesized by living ring-opening metathesis polymerization. 18 figs.

Kent, M.S.; Saunders, R.

1997-02-18T23:59:59.000Z

102

VISION - Verifiable Fuel Cycle Simulation of Nuclear Fuel Cycle Dynamics  

SciTech Connect (OSTI)

The U.S. DOE Advanced Fuel Cycle Initiatives (AFCI) fundamental objective is to provide technology options that - if implemented - would enable long-term growth of nuclear power while improving sustainability and energy security. The AFCI organization structure consists of four areas; Systems Analysis, Fuels, Separations and Transmutations. The Systems Analysis Working Group is tasked with bridging the program technical areas and providing the models, tools, and analyses required to assess the feasibility of design and deployment options and inform key decision makers. An integral part of the Systems Analysis tool set is the development of a system level model that can be used to examine the implications of the different mixes of reactors, implications of fuel reprocessing, impact of deployment technologies, as well as potential "exit" or "off ramp" approaches to phase out technologies, waste management issues and long-term repository needs. The Verifiable Fuel Cycle Simulation Model (VISION) is a computer-based simulation model that allows performing dynamic simulations of fuel cycles to quantify infrastructure requirements and identify key trade-offs between alternatives. It is based on the current AFCI system analysis tool "DYMOND-US" functionalities in addition to economics, isotopic decay, and other new functionalities. VISION is intended to serve as a broad systems analysis and study tool applicable to work conducted as part of the AFCI and Generation IV reactor development studies.

Steven J. Piet; A. M. Yacout; J. J. Jacobson; C. Laws; G. E. Matthern; D. E. Shropshire

2006-02-01T23:59:59.000Z

103

On the origin of irregular structure in Saturn's rings  

E-Print Network [OSTI]

We suggest that the irregular structure in Saturn's B ring arises from the formation of shear-free ring-particle assemblies of up to ~100 km in radial extent. The characteristic scale of the irregular structure is set by the competition between tidal forces and the yield stress of these assemblies; the required tensile strength of ~10^5 dyn/cm^2 is consistent with the sticking forces observed in laboratory simulations of frosted ice particles. These assemblies could be the nonlinear outcome of a linear instability that occurs in a rotating fluid disk in which the shear stress is a decreasing function of the shear. We show that a simple model of an incompressible, non-Newtonian fluid in shear flow leads to the Cahn-Hilliard equation, which is widely used to model the formation of structure in binary alloys and other systems.

Scott Tremaine

2002-11-07T23:59:59.000Z

104

Coherence theory of the ring laser  

Science Journals Connector (OSTI)

Expressions for the fluctuations and correlations of the light emitted by a ring laser with counter-rotating traveling wave modes are derived theoretically. It is shown that the competition of the two modes for the excited atomic population leads to negative correlations between their intensity fluctuations, whose magnitude depends on the detuning of the laser cavity from the atomic line center. As a result of the mode competition, the relative intensity fluctuations do not die out in general as the working point of the laser is raised above threshold at line center, and the emitted light does not become fully coherent as in a conventional laser. The two-time amplitude and intensity correlation functions of the light are calculated at line center, and are shown to be expressible in terms of the eigenfunctions and eigenvalues of a certain Schrdinger equation, in complete analogy with the theory of the single-mode laser. However, the intensity correlation time increases with pump parameter above threshold, unlike that for the single-mode laser.

M. M- Tehrani and L. Mandel

1978-02-01T23:59:59.000Z

105

Thermal Stability of Cyclopentane as an Organic Rankine Cycle Working Fluid  

Science Journals Connector (OSTI)

Thermal Stability of Cyclopentane as an Organic Rankine Cycle Working Fluid ... Because of the rather low molecular weight of water, the use of steam Rankine cycles for waste heat temperatures below 400 C is inefficient and requires the use of expensive multistage expanders. ... Cyclopentane (C5H10) is a cyclic alkane that exhibits a puckered (i.e., one carbon atom tends to jut out above the others to relieve ring stress) ring system of carbonhydrogen (CH) bonds and carboncarbon (CC) single bonds. ...

Daniel M. Ginosar; Lucia M. Petkovic; Donna Post Guillen

2011-08-02T23:59:59.000Z

106

Power Plant Cycling Costs  

SciTech Connect (OSTI)

This report provides a detailed review of the most up to date data available on power plant cycling costs. The primary objective of this report is to increase awareness of power plant cycling cost, the use of these costs in renewable integration studies and to stimulate debate between policymakers, system dispatchers, plant personnel and power utilities.

Kumar, N.; Besuner, P.; Lefton, S.; Agan, D.; Hilleman, D.

2012-07-01T23:59:59.000Z

107

Life Cycle Cost Estimate  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

Life-cycle costs (LCCs) are all the anticipated costs associated with a project or program alternative throughout its life. This includes costs from pre-operations through operations or to the end of the alternative.This chapter discusses life cycle costs and the role they play in planning.

1997-03-28T23:59:59.000Z

108

Molecular Model of the Contractile Ring  

E-Print Network [OSTI]

We present a model for the actin contractile ring of adherent animal cells. The model suggests that the actin concentration within the ring and consequently the power that the ring exerts both increase during contraction. We demonstrate the crucial role of actin polymerization and depolymerization throughout cytokinesis, and the dominance of viscous dissipation in the dynamics. The physical origin of two phases in cytokinesis dynamics ("biphasic cytokinesis") follows from a limitation on the actin density. The model is consistent with a wide range of measurements of the midzone of dividing animal cells.

D. Biron; E. Alvarez-Lacalle; Tsvi Tlusty; Elisha Moses

2010-08-05T23:59:59.000Z

109

Liner surface improvements for low friction piston ring packs  

Science Journals Connector (OSTI)

The development of engine components in the automotive industry is governed by several constraints such as environmental legislation and customer expectations. About a half of the frictional losses in an internal combustion engine come from the interactions between the piston assembly and cylinder liner surface. The tribological considerations in the contact between the piston ring and cylinder liner have attracted much attention over the past few decades. Many non-conventional cylinder liner finishes have been, and are being, developed with the aim to reduce friction losses and oil consumption, but the effects of the surface finish on piston ring pack performance is not well understood. One way of reducing friction in the cylinder system is to reduce the tangential load from the piston ring pack, focusing on the oil control ring. However, the side-effect of this is a disappointingly increased oil consumption. Inthis study a number of different cylinder liner surface specifications were developed and implemented in test engines with the aim of maintaining the level for oil consumption when decreasing the tangential load for the piston ring pack. To improve our understanding of the result, the same surfaces were evaluated in elastic and elasto-plastic rough contact and hydrodynamic flow simulation models. It is shown that oil consumption is strongly related to surface texture on the cylinder liners and at lower speeds (9001200rpm), a 'rougher surface' with a high core (e.g. Sk) and valley roughness (e.g. Svk) results in higher oil consumption. Atthe medium speed range (12003600rpm), oil consumption continues to dominate for the 'rough' surfaces but with a visible influence of a lower oil consumption for a decreased roughness within the 'rough' surface group. 'Smooth' surfaces with a 'smooth' core (Sk), irrespective of the valley component (Svk), show similar oil consumption. For engine speeds above 3600rpms, an increase in plateau roughness results in higher oil consumption. Throughout the study, standard roughness parameters were computed to compare with the results from engine testing and simulation. Future work will be directed to continuous optimization between oil consumption and friction. Improving the understanding of the functional cylinder system surfaces' ability to form oil films in the cylinder system opens up opportunities, not only in reducing the tangential load of piston ring packs but also in optimizing oil viscosity in order to reduce friction.

C Anderberg; Z Dimkovski; B-G Rosn

2014-01-01T23:59:59.000Z

110

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

111

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

112

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

113

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

114

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

115

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

116

RingCentral Mailboxes | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Description RingCentral Mailboxes Responsible Contacts Bruce Murray HR Policy Advisor E-mail bruce.murray@hq.doe.gov Phone 202-586-3372 More Documents & Publications...

117

The MAX IV storage ring project  

Science Journals Connector (OSTI)

The design of the MAX IV 3 GeV ultralow-emittance storage ring is presented and the implementation of solutions to the technological challenges imposed by the compact multi-bend achromat lattice are described.

Tavares, P.F.

2014-08-27T23:59:59.000Z

118

Storage rings for spin-polarized hydrogen  

Science Journals Connector (OSTI)

A strong-focusing storage ring is proposed for the long-term magnetic confinement of a collisional gas of neutral spin-polarized hydrogen atoms in the |a? and |b? hyperfine states. The...

Thompson, D; Lovelace, R V E; Lee, D M

1989-01-01T23:59:59.000Z

119

Low thermal expansion seal ring support  

DOE Patents [OSTI]

Today, the trend is to increase the temperature of operation of gas turbine engines. To cool the components with compressor discharge air, robs air which could otherwise be used for combustion and creates a less efficient gas turbine engine. The present low thermal expansion sealing ring support system reduces the quantity of cooling air required while maintaining life and longevity of the components. Additionally, the low thermal expansion sealing ring reduces the clearance "C","C'" demanded between the interface between the sealing surface and the tip of the plurality of turbine blades. The sealing ring is supported by a plurality of support members in a manner in which the sealing ring and the plurality of support members independently expand and contract relative to each other and to other gas turbine engine components.

Dewis, David W. (San Diego, CA); Glezer, Boris (Del Mar, CA)

2000-01-01T23:59:59.000Z

120

Power Ring LLC | Open Energy Information  

Open Energy Info (EERE)

Ring LLC Ring LLC Jump to: navigation, search Name Power Ring LLC Place Goleta, California Zip 93117 Product Power Ring is a power storage technology developer working on technology developed by parent firm LaunchPoint Technologies. Coordinates 34.435682°, -119.824105° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":34.435682,"lon":-119.824105,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

The endomorphism near ring on D?  

E-Print Network [OSTI]

THE FNDOMORPHISM NEAR RING ON Dg A Thesis by Fdgar Raymond Guthrie Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirements for the degree of MASTFR OF SCIENCE ~A 1969 (Month) (Year) Major... Subject: Mathematics THE ENDOMORPHISM NEAR RING ON Dg A Thesis by Edgar Raymond Guthrie Approved as to style and content by: (Cha' of Committee) (YAead of Department) (Member) (Member) (Member) (Member) ~AA 1969 (Month) (Year) ABSTRACT...

Guthrie, Edgar Raymond

1969-01-01T23:59:59.000Z

122

Molecular Model of the Ring-Opening and Ring-Closure Reaction of a Fluorinated Indolylfulgide  

Science Journals Connector (OSTI)

Next, the role of the seam is elucidated by focusing on the energetic and structural characteristics of two further CoIns from that seam, one in the closed-ring region (CoInC) and one in the open-ring region (CoIncZc/tZc). ... A similar constellation is found at the open-ring side, where CoIncZc/tZc could be located (Figure 6, bottom). ... ring opening process in pyrrole has been investigated by performing classical on-the-fly dynamics using the multiconfiguration SCF method for the computation of energies and energy gradients. ...

Artur Nenov; Wolfgang J. Schreier; Florian O. Koller; Markus Braun; Regina de Vivie-Riedle; Wolfgang Zinth; Igor Pugliesi

2012-09-29T23:59:59.000Z

123

The Carbon Cycle  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

The Carbon Cycle The Carbon Cycle The global carbon cycle involves the carbon in and exchanging between the earth's atmosphere, fossil fuels, the oceans, and the vegetation and soils of the earth's terrestrial ecosystems. image Each year, the world's terrestrial ecosystems withdraw carbon from the atmosphere through photosynthesis and add it again through respiration and decay. A more detailed look at the global carbon cycle for the 1990s is shown below. The main annual fluxes in GtC yr-1 are: pre-industrial "natural" fluxes in black and "anthropogenic" fluxes in red (modified from Sarmiento and Gruber, 2006, with changes in pool sizes from Sabine et al., 2004a). The net terrestrial loss of -39 GtC is inferred from cumulative fossil fuel emissions minus atmospheric increase minus ocean storage. The loss of

124

Wetland (peat) Carbon Cycle  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Wetland (peat) Carbon Cycle Methane (CH4) is an important greenhouse gas, twenty times more potent than CO2, but atmospheric concentrations of CH4 under future climate change are...

125

The Completion of an Archimedean f-Ring  

Science Journals Connector (OSTI)

......archimedean /-ring has a completion; in fact, every such ring...and closed sets in SC. THE COMPLETION OF AN ABCHIMEDEAN /-RING...there is a point ye% and and index AeA such that/A(y...Theorem except LEMMA 3. The completion of an archimedean f-ring......

D. G. Johnson

1965-01-01T23:59:59.000Z

126

IFR fuel cycle  

SciTech Connect (OSTI)

The next major milestone of the IFR program is engineering-scale demonstration of the pyroprocess fuel cycle. The EBR-II Fuel Cycle Facility has just entered a startup phase, which includes completion of facility modifications and installation and cold checkout of process equipment. This paper reviews the development of the electrorefining pyroprocess, the design and construction of the facility for the hot demonstration, the design and fabrication of the equipment, and the schedule and initial plan for its operation.

Battles, J.E.; Miller, W.E. [Argonne National Lab., IL (United States); Lineberry, M.J.; Phipps, R.D. [Argonne National Lab., Idaho Falls, ID (United States)

1992-04-01T23:59:59.000Z

127

FUEL CYCLE POTENTIAL WASTE FOR DISPOSITION  

SciTech Connect (OSTI)

The United States (U.S.) currently utilizes a once-through fuel cycle where used nuclear fuel (UNF) is stored on-site in either wet pools or in dry storage systems with ultimate disposal in a deep mined geologic repository envisioned. Within the Department of Energy's (DOE) Office of Nuclear Energy (DOE-NE), the Fuel Cycle Research and Development Program (FCR&D) develops options to the current commercial fuel cycle management strategy to enable the safe, secure, economic, and sustainable expansion of nuclear energy while minimizing proliferation risks by conducting research and development of advanced fuel cycles, including modified open and closed cycles. The safe management and disposition of used nuclear fuel and/or nuclear waste is a fundamental aspect of any nuclear fuel cycle. Yet, the routine disposal of used nuclear fuel and radioactive waste remains problematic. Advanced fuel cycles will generate different quantities and forms of waste than the current LWR fleet. This study analyzes the quantities and characteristics of potential waste forms including differing waste matrices, as a function of a variety of potential fuel cycle alternatives including: (1) Commercial UNF generated by uranium fuel light water reactors (LWR). Four once through fuel cycles analyzed in this study differ by varying the assumed expansion/contraction of nuclear power in the U.S. (2) Four alternative LWR used fuel recycling processes analyzed differ in the reprocessing method (aqueous vs. electro-chemical), complexity (Pu only or full transuranic (TRU) recovery) and waste forms generated. (3) Used Mixed Oxide (MOX) fuel derived from the recovered Pu utilizing a single reactor pass. (4) Potential waste forms generated by the reprocessing of fuels derived from recovered TRU utilizing multiple reactor passes.

Carter, J.

2011-01-03T23:59:59.000Z

128

FUEL CYCLE POTENTIAL WASTE FOR DISPOSITION  

SciTech Connect (OSTI)

The United States (U.S.) currently utilizes a once-through fuel cycle where used nuclear fuel (UNF) is stored on-site in either wet pools or in dry storage systems with ultimate disposal in a deep mined geologic repository envisioned. Within the Department of Energy's (DOE) Office of Nuclear Energy (DOE-NE), the Fuel Cycle Research and Development Program (FCR&D) develops options to the current commercial fuel cycle management strategy to enable the safe, secure, economic, and sustainable expansion of nuclear energy while minimizing proliferation risks by conducting research and development of advanced fuel cycles, including modified open and closed cycles. The safe management and disposition of used nuclear fuel and/or nuclear waste is a fundamental aspect of any nuclear fuel cycle. Yet, the routine disposal of used nuclear fuel and radioactive waste remains problematic. Advanced fuel cycles will generate different quantities and forms of waste than the current LWR fleet. This study analyzes the quantities and characteristics of potential waste forms including differing waste matrices, as a function of a variety of potential fuel cycle alternatives including: (1) Commercial UNF generated by uranium fuel light water reactors (LWR). Four once through fuel cycles analyzed in this study differ by varying the assumed expansion/contraction of nuclear power in the U.S; (2) Four alternative LWR used fuel recycling processes analyzed differ in the reprocessing method (aqueous vs. electro-chemical), complexity (Pu only or full transuranic (TRU) recovery) and waste forms generated; (3) Used Mixed Oxide (MOX) fuel derived from the recovered Pu utilizing a single reactor pass; and (4) Potential waste forms generated by the reprocessing of fuels derived from recovered TRU utilizing multiple reactor passes.

Jones, R.; Carter, J.

2010-10-13T23:59:59.000Z

129

Malone cycle refrigerator development  

SciTech Connect (OSTI)

This paper describes the progress made in demonstrating a Malone Cycle Refrigerator/Freezer. The Malone cycle is similar to the Stirling cycle but uses a supercritical fluid in place of real gas. In the approach, solid-metal diaphragms are used to seal and sweep the working volumes against the high working fluid pressures required in Malone cycle machines. This feature eliminates the friction and leakage that accounted for nearly half the losses in the best piston-defined Malone cycle machines built to date. The authors successfully built a Malone cycle refrigerator that: (1) used CO{sub 2} as the working fluid, (2) operated at pressures up to 19.3 Mpa (2,800 psi), (3) achieved a cold end metal temperatures of {minus}29 C ({minus}20 F), and (4) produced over 400 Watts of cooling at near ambient temperatures. The critical diaphragm components operated flawlessly throughout characterization and performance testing, supporting the conclusion of high reliability based on analysis of fatigue date and actual strain measurements.

Shimko, M.A.; Crowley, C.J.

1999-07-01T23:59:59.000Z

130

Gasket and snap ring installation tool  

DOE Patents [OSTI]

A tool for installing a gasket and a snap ring including a shaft, a first plate attached to the forward end of the shaft, a second plate slidably carried by the shaft, a spring disposed about the shaft between the first and second plates, and a sleeve that is free to slide over the shaft and engage the second plate. The first plate has a loading surface with a loading groove for receiving a snap ring and a shoulder for holding a gasket. A plurality of openings are formed through the first plate, communicating with the loading groove and approximately equally spaced about the groove. A plurality of rods are attached to the second plate, each rod slidable in one of the openings. In use, the loaded tool is inserted into a hollow pipe or pipe fitting having an internal flange and an internal seating groove, such that the gasket is positioned against the flange and the ring is in the approximate plane of the seating groove. The sleeve is pushed against the second plate, sliding the second plate towards the first plate, compressing the spring and sliding the rods forwards in the openings. The rods engage the snap ring and urge the ring from the loading groove into the seating groove.

Southerland, Jr., James M. (Aiken, SC); Barringer, Jr., Curtis N. (Orangeburg, SC)

1994-01-01T23:59:59.000Z

131

Helium process cycle  

DOE Patents [OSTI]

A unique process cycle and apparatus design separates the consumer (cryogenic) load return flow from most of the recycle return flow of a refrigerator and/or liquefier process cycle. The refrigerator and/or liquefier process recycle return flow is recompressed by a multi-stage compressor set and the consumer load return flow is recompressed by an independent consumer load compressor set that maintains a desirable constant suction pressure using a consumer load bypass control valve and the consumer load return pressure control valve that controls the consumer load compressor's suction pressure. The discharge pressure of this consumer load compressor is thereby allowed to float at the intermediate pressure in between the first and second stage recycle compressor sets. Utilizing the unique gas management valve regulation, the unique process cycle and apparatus design in which the consumer load return flow is separate from the recycle return flow, the pressure ratios of each recycle compressor stage and all main pressures associated with the recycle return flow are allowed to vary naturally, thus providing a naturally regulated and balanced floating pressure process cycle that maintains optimal efficiency at design and off-design process cycle capacity and conditions automatically.

Ganni, Venkatarao (Yorktown, VA)

2008-08-12T23:59:59.000Z

132

Helium process cycle  

DOE Patents [OSTI]

A unique process cycle and apparatus design separates the consumer (cryogenic) load return flow from most of the recycle return flow of a refrigerator and/or liquefier process cycle. The refrigerator and/or liquefier process recycle return flow is recompressed by a multi-stage compressor set and the consumer load return flow is recompressed by an independent consumer load compressor set that maintains a desirable constant suction pressure using a consumer load bypass control valve and the consumer load return pressure control valve that controls the consumer load compressor's suction pressure. The discharge pressure of this consumer load compressor is thereby allowed to float at the intermediate pressure in between the first and second stage recycle compressor sets. Utilizing the unique gas management valve regulation, the unique process cycle and apparatus design in which the consumer load return flow is separate from the recycle return flow, the pressure ratios of each recycle compressor stage and all main pressures associated with the recycle return flow are allowed to vary naturally, thus providing a naturally regulated and balanced floating pressure process cycle that maintains optimal efficiency at design and off-design process cycle capacity and conditions automatically.

Ganni, Venkatarao (Yorktown, VA)

2007-10-09T23:59:59.000Z

133

CALIXARENE-ENCAPSULATED COBALT NANOPARTICLE RINGS Kasama, T.; Dunin-Borkowski, R. E.; Scheinfein, M. R.; Tripp, S. L.; Liu, J.; Wei, A.  

E-Print Network [OSTI]

CALIXARENE-ENCAPSULATED COBALT NANOPARTICLE RINGS Kasama, T.; Dunin-Borkowski, R. E.; Scheinfein, M and inorganic nanoparticles, and can mediate their self-assembly into functional nanostructures with intriguing (FC) states of Co nanoparticle rings, and their potential for nonvolatile memory applications. Weakly

Dunin-Borkowski, Rafal E.

134

SNS Ring, Spallation Neutron Source, SNS  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

RING RING Lattice Version 1.0 in MAD structure Version 1.1: SNSRing.v.1.1 | 623_620_00.mad Version 1.2 SNSRing.v.1.2 | 623_620_00.mad Matching example MAD optics outputs UAL compatible input example Schematic (one super-period) and mechanical drawing Diagnostics Impedance budget Magnets List and mechanical parameters Mechanical drawings Magnetic field modeling and measurements Installation and survey Power supplies summary and changes Polarity conventions tech.memo and schematic (A polarity) Magnet assemblies Documentation ASAC review presentations DOE review presentations SNS/BNL tech.notes, conference and journal papers SNS/ORNL papers SNS project documentation Other links SNS ring aperture, collimation and beam losses SNS transfer lines SNS/BNL Accelerator Physics SNS/ORNL Accelerator Physics

135

Photoneutron production inside the APS Storage Ring  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

4 4 Neutron Fluence Estimates Inside the APS Storage Ring During Normal Operation P.K. Job and J. Alderman Advanced Photon Source Argonne National Laboratory April 2002 Neutron Fluence Estimates Inside the APS Storage Ring During Normal Operation P.K. Job and J. Alderman Advanced Photon Source Argonne National Laboratory April 2002 Introduction In an electron storage ring, neutrons are generated as a result of the electron beam interaction with high-Z materials, such as scrapers and collimators [1]. When the energy of the incident electron beam is sufficiently high, it can produce high-energy photons, which subsequently interact with a nucleus, resulting in the emission of nucleons. This interaction is known as a photonuclear interaction. For photons with energies above the

136

CHALLENGES FOR THE SNS RING ENERGY UPGRADE  

SciTech Connect (OSTI)

The Oak Ridge Spallation Neutron Source accumulator ring presently operates at a beam power of about 1 MW with a beam energy of about 910 MeV. A power upgrade is planned to increase the beam energy to 1.3 GeV. For the accumulator ring this mostly involves modifications to the injection and extraction sections. A variety of modifications to the existing injection section were necessary to achieve 1 MW, and the tools developed and the lessons learned from this work are now being applied to the design of the new injection section. This paper will discuss the tools and the lessons learned, and also present the design and status of the upgrades to the accumulator ring.

Plum, Michael A [ORNL; Gorlov, Timofey V [ORNL; Holmes, Jeffrey A [ORNL; Hunter, W Ted [ORNL; Roseberry, Jr., R Tom [ORNL; Wang, Jian-Guang [ORNL

2012-01-01T23:59:59.000Z

137

Coherence and persistent currents in mesoscopic rings  

Science Journals Connector (OSTI)

We calculate, to first order in the screened electron-electron interaction, the grand potential and the equilibrium current in a mesoscopic normal-metal ring threaded by a magnetic flux. The average current in an ensemble of such rings is found to be periodic in the flux with period h/2e, and to be given at zero temperature in order of magnitude by I?evFl/L2, where l is the mean free path and L the circumference of the ring. Interference between time-reversed paths, as in the theory of weak localization, is the crucial ingredient. The effect decreases exponentially with temperature on a scale determined by the coherence energy ?hD/L2, where D is the electronic diffusion constant. The results are in good agreement with recent measurements.

Vinay Ambegaokar and Ulrich Eckern

1990-07-16T23:59:59.000Z

138

On cohomology rings of infinite groups.  

E-Print Network [OSTI]

Let R be any ring (with 1), \\Gamma a group and R\\Gamma the corresponding group ring. Let Ext_{R\\Gamma}^{*}(M,M) be the cohomology ring associated to the R\\Gamma-module M. Let H be a subgroup of finite index of \\Gamma. The following is a special version of our main Theorem: Assume the profinite completion of \\Gamma is torsion free. Then an element \\zeta in Ext_{R\\Gamma}^{*}(M,M) is nilpotent (under Yoneda's product) if and only if its restriction to Ext_{RH}^{*}(M,M)$ is nilpotent. In particular this holds for the Thompson group. There are torsion free groups for which the analogous statement is false.

Eli Aljadeff

139

Power Plant Cycling Costs  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Power Plant Cycling Costs Power Plant Cycling Costs April 2012 N. Kumar, P. Besuner, S. Lefton, D. Agan, and D. Hilleman Intertek APTECH Sunnyvale, California NREL Technical Monitor: Debra Lew Subcontract Report NREL/SR-5500-55433 July 2012 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 15013 Denver West Parkway Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Power Plant Cycling Costs April 2012 N. Kumar, P. Besuner, S. Lefton, D. Agan, and D. Hilleman Intertek APTECH Sunnyvale, California NREL Technical Monitor: Debra Lew Prepared under Subcontract No. NFT-1-11325-01

140

Progress and commissioning of the SLD Cherenkov Ring Imaging Detector  

SciTech Connect (OSTI)

We report the recent progress of the SLD Cherenkov Ring Imaging Detector. All of the individual components of the device (TPC's, mirrors, liquid radiator trays) have been completed and installed. Almost half of the electronics packages are installed and operational, and the data acquisition system has been commissioned. The liquid C{sub 6}F{sub 14} recirculation system is functioning. The drift gas supply systems are operating well with TMAE, and the gaseous Freon C{sub 5}F{sub 12} recirculator is being brought on-line. Our monitor and control systems are fully functional. The commissioning of all 40 TPCs at full operating voltage has gone very smoothly. The system shows a remarkable immunity to the SLC backgrounds, and yields very clean events, while operating with a single electron sensitivity.

Abe, K.; Hasegawa, K.; Suekane, F.; Yuta, H. (Tohoku Univ., Sendai (Japan). Dept. of Physics); Antilogus, P.; Aston, D.; Bienz, T.; Bird, F.; Dasu, S.; Dolinsky, S.; Dunwoodie, W.; Hallewell, G.: Kawahara, H.; Kwon, Y.; Leith, D.W.G.S.; Muller, D.; Nagamine, T.; Pavel, T.J.; Ratcliff, B.; Rensing, P.; Schultz, D.; Shapiro, S.; Simopoulos, C.; Solodov, E.; Toge, N.; Va'vra, J.; Williams, S.H. (Stanford Linear Accelerator

1991-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Ground Ring Of Two Dimensional String Theory  

E-Print Network [OSTI]

String theories with two dimensional space-time target spaces are characterized by the existence of a ``ground ring'' of operators of spin $(0,0)$. By understanding this ring, one can understand the symmetries of the theory and illuminate the relation of the critical string theory to matrix models. The symmetry groups that arise are, roughly, the area preserving diffeomorphisms of a two dimensional phase space that preserve the fermi surface (of the matrix model) and the volume preserving diffeomorphisms of a three dimensional cone. The three dimensions in question are the matrix eigenvalue, its canonical momentum, and the time of the matrix model.

Edward Witten

1991-08-16T23:59:59.000Z

142

Structure of middle distillate fuels on the atomic carbon and hydrogen to carbon ratio at alpha position to aromatic rings  

SciTech Connect (OSTI)

The alkyl, naphthenic, or total carbon atoms of the functional groups at alpha position to aromatic rings and their hydrogen to carbon ratio are some of the important parameters for structural analysis of fossil fuel products. In this paper, the authors present a number of novel formula-structure relationships for precise determination of different carbon atom types at alpha position to aromatic rings and the average number of hydrogens per alpha-carbon.

Glavincevski, B.; Gulder, O.L.; Gardner, L

1988-01-01T23:59:59.000Z

143

Life cycle assessment framework in agriculture on the farm level  

Science Journals Connector (OSTI)

Life Cycle Assessment (LCA) is a method that can be used to assess the environmental impact of agriculture, but impact categories and the functional unit of classical LCAs must be adapted to the specific ... as ...

Guido Haas; Frank Wetterich

2000-11-01T23:59:59.000Z

144

mathematical Study program cycle  

E-Print Network [OSTI]

TSW ECTS TSW Fundamentals of statistics 2 2 0 5 150 0 0 0 0 0 5 150 Probability 4 3 0 10 300 0 0 0 0 0127 mathematical statistics Master's study programms #12;128 #12;· Study program cycle: Second Statistics. In Slovenian: magister matematicne statistike (masculine), magistrica matematicne statistike

?umer, Slobodan

145

CLASS DESCRIPTIONS CYCLING SERIES  

E-Print Network [OSTI]

will utilize concepts from the 50-minute cycling class while going the distance to optimal health. Whether you're an avid cyclist, triathlete, or desire a longer class for a greater challenge, join us for this 75-minute AN URBANATHLETE Are you registered to compete in an adventure race like the Men's Health Urbanathlon, Warrior Dash

Pittendrigh, Barry

146

Rankine cycle power plant with improved organic working fluid  

SciTech Connect (OSTI)

In a Rankine cycle power plant having a boiler for vaporizing an organic working fluid which is applied to a turbine in which vaporized working fluid produced by the boiler expands and produces work, a condenser for condensing expanded vaporized working fluid exhausted by the turbine and producing condensate, and means for returning the condensate to the boiler, the improvement is described comprising: (a) operating the boiler so that the organic fluid vaporizes at substantially constant pressure and a temperature not exceeding 400/sup 0/C; (b) applying only vaporized working fluid to the turbine; and (c) using as the working fluid, a compound selected from the group consisting of bicyclic hydrocarbons, substituted bicyclic aromatic hydrocarbons, heterobicyclic aromatic hydrocarbons, substituted heterobicyclic aromatic hydrocarbons, bicyclic compounds where one ring is aromatic and the other condensed ring is nonaromatic, and their mixtures.

Yogev, A.; Mahlab, D.

1988-08-02T23:59:59.000Z

147

Dissociative recombination: Results from storage rings  

SciTech Connect (OSTI)

The focus of this article is on the measurement of product branching ratios in the dissociative recombination of polyatomic molecular ions with electrons by means of ion storage rings. Recombination of ions of interest in astrophysics, plasma-assisted combustion, thermonuclear fusion, protein fragmentation, and atmospheric physics are reviewed and discussed.

Larsson, Mats [Department of Physics, AlbaNova, Stockholm University, Stockholm, SE-106 91 (Sweden)

2005-05-27T23:59:59.000Z

148

Correction magnets for the Fermilab Recycler Ring  

SciTech Connect (OSTI)

In the commissioning of the Fermilab Recycler ring the need for higher order corrector magnets in the regions near beam transfers was discovered. Three types of permanent magnet skew quadrupoles, and two types of permanent magnet sextupoles were designed and built. This paper describes the need for these magnets, the design, assembly, and magnetic measurements.

James T Volk et al.

2003-05-27T23:59:59.000Z

149

Knot localization in adsorbing polymer rings  

E-Print Network [OSTI]

We study by Monte Carlo simulations a model of knotted polymer ring adsorbing onto an impenetrable, attractive wall. The polymer is described by a self-avoiding polygon (SAP) on the cubic lattice. We find that the adsorption transition temperature, the crossover exponent $\\phi$ and the metric exponent $\

B. Marcone; E. Orlandini; A. L. Stella

2007-09-10T23:59:59.000Z

150

Persistent Currents in Normal Metal Rings  

Science Journals Connector (OSTI)

...C) the 793-nm array for T = 323 mK, {theta} = 6; and (D) the 418-nm ring for 365 mK, {theta} = 45. In each case, a smooth...using measurements of the PC to search for ultralow temperature phase transitions (6...

A. C. Bleszynski-Jayich; W. E. Shanks; B. Peaudecerf; E. Ginossar; F. von Oppen; L. Glazman; J. G. E. Harris

2009-10-09T23:59:59.000Z

151

RF SYSTEM FOR THE SNS ACCUMULATOR RING.  

SciTech Connect (OSTI)

During accumulation the RF beam current in the spallation neutron source ring rises from 0 to 50 amperes. A clean, 250 nanosecond gap is needed for the extraction kicker risetime. Large momentum spread and small peak current are needed to prevent instabilities and stopband related losses. A robust RF system meeting these requirements has been designed.

BLASKIEWICZ, M.; BRENNAN, J.M.; BRODOWSKI, J.; DELONG, J.; METH, M.; SMITH, K.; ZALTSMAN, A.

2001-06-18T23:59:59.000Z

152

Intrabeam Scattering Studies for the ILC Damping Rings Using a NewMATLAB Code  

SciTech Connect (OSTI)

A new code to calculate the effects of intrabeam scattering (IBS) has been developed in MATLAB based on the approximation suggested by K. Bane. It interfaces with the Accelerator Toolbox but can also read in lattice functions from other codes. The code has been benchmarked against results from other codes for the ATF that use this approximation or do the calculation in a different way. The new code has been used to calculate the emittance growth due to intrabeam scattering for the lattices currently proposed for the ILC Damping Rings, as IBS is a concern, especially for the electron ring. A description of the code and its user interface, as well as results for the Damping Rings, will be presented.

Reichel, I.; Wolski, A.

2006-06-21T23:59:59.000Z

153

Interaction Region Design for a Ring-Ring LHeC  

E-Print Network [OSTI]

tively low energy and moderately high intensity provides high luminosity TeV-scale e-p collisions at one of the LHC interaction points, running simultaneously with existing experiments. Two designs are studied; an electron ring situated in the LHC tunnel, and an electron linac. The focus of this paper is on the ring design. Designing an e-p machine presents interesting accelerator physics and design challenges, particularly when considering the interaction region. These include coupled optics, beam separation and unconventional mini-beta focusing schemes. Designs are constrained by an array of interdependent factors, including beam-beam interaction, detector dimensions and acceptance, luminosity and synchrotron radiation. Methods of addressing these complex issues are discussed. The current designs for the LHeC Ring-Ring interaction region and long straight section are presented and discussed, in the context of the project goals and design challenges encountered. Future developments and work are also discusse...

Thompson, L N S; Bernard, N R; Fitterer, M; Holzer, B; Klein, M; Kostka, P

2011-01-01T23:59:59.000Z

154

D-Cycle - 4-Differential -Stroke Cycle | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

-Stroke Cycle The D-Cycle offers the opportunity to use less fuel and gain more power while being able to be retrofit to an OEM and aftermarket engines deer09conti.pdf...

155

RingCentral User Guide | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

called RingCentral. RingCentral User Guide Responsible Contacts Bruce Murray HR Policy Advisor E-mail bruce.murray@hq.doe.gov Phone 202-586-3372 More Documents & Publications US...

156

Reaction of arylsulfonyl compounds with excess organolithium reagent 10. Opening of the thiophene ring in?-lithium derivatives of 2,5-bis(tert-butylsulfonyl)thiophene  

Science Journals Connector (OSTI)

Opening of the thiophene ring is observed in the lithium derivatives of 2,5-bis(t-butylsulfonyl)thiophene, resulting in the formation of functionally substituted dienes of their transformation products.

F. M. Stoyanovich; G. B. Chermanova

1977-06-01T23:59:59.000Z

157

Gas insulated transmission line having tapered particle trapping ring  

DOE Patents [OSTI]

A gas-insulated transmission line includes an outer sheath, an inner conductor, insulating supports and an insulating gas. A particle-trapping ring is secured to each insulating support, and it is comprised of a central portion and two tapered end portions. The ends of the particle trapping ring have a smaller diameter than the central portion of the ring, so as to enable the use of the particle trapping ring in a curved transmission line.

Cookson, Alan H. (Pittsburgh, PA)

1982-01-01T23:59:59.000Z

158

BNL | Carbon Cycle Science  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

The Carbon Cycle Science & Technology Group aims to increase understanding The Carbon Cycle Science & Technology Group aims to increase understanding of the impacts of global change on managed and unmanaged ecosystems and improve knowledge of possible global change mitigation approaches. The group has three main focus areas. FACE Climate Change Experimental Facility Design and Management The CCS&T group is an internationally recognized leader in the development of Free Air CO2 Enrichment (FACE) research facilities. We are interested in the design and management of manipulative experiments that examine the effects of carbon dioxide, ozone, other atmospheric pollutants, temperature and precipitation on natural and managed ecosystems. FACE Plant Physiology and High Throughput Biochemical Phenotyping At FACE facilities we have studied the mechanisms that underlie the

159

Fuel Cycle Subcommittee  

Broader source: Energy.gov (indexed) [DOE]

Report to NEAC Report to NEAC Fuel Cycle Subcommittee Meeting of April 23, 2013 Washington D.C. June 13, 2013 Burton Richter (Chair), Margaret Chu, Darleane Hoffman, Raymond Juzaitis, Sekazi K Mtingwa, Ronald P Omberg, Joy L Rempe, Dominique Warin 2 I Introduction and Summary The Fuel Cycle Subcommittee of NEAC met in Washington on April 23, 2013. The meeting focused on issues relating to the NE advanced reactor program (sections II, III, and IV), and on storage and transportation issues (section V) related to a possible interim storage program that is the first step in moving toward a new permanent repository as recommended by the Blue Ribbon Commission (BRC) and discussed in the recent response by DOE to Congress on the BRC report 1 . The agenda is given in

160

CANDU fuel cycle flexibility  

SciTech Connect (OSTI)

High neutron economy, on-power refuelling, and a simple bundle design provide a high degree of flexibility that enables CANDU (CANada Deuterium Uranium; registered trademark) reactors to be fuelled with a wide variety of fuel types. Near-term applications include the use of slightly enriched uranium (SEU), and recovered uranium (RU) from reprocessed spent Light Water Reactor (LWR) fuel. Plutonium and other actinides arising from various sources, including spent LWR fuel, can be accommodated, and weapons-origin plutonium could be destroyed by burning in CANDU. In the DUPIC fuel cycle, a dry processing method would convert spent Pressurized Water Reactor (PWR) fuel to CANDU fuel. The thorium cycle remains of strategic interest in CANDU to ensure long-term resource availability, and would be of specific interest to those countries possessing large thorium reserves, but limited uranium resources.

Torgerson, D.F.; Boczar, P.G. [Chalk River Lab., Ontario (Canada); Dastur, A.R. [AECL CANDU, Mississauga, Ontario (Canada)

1994-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

USCEA fuel cycle '93  

SciTech Connect (OSTI)

The US Council for Energy Awareness sponsored the Fuel Cycle '93 conference in Dallas, Texas, on March 21-24, 1993. Over 250 participants attended, numerous papers were presented, and several panel discussions were held. The focus of most industry participants remains the formation of USEC and the pending US-Russian HEU agreement. Following are brief summaries of two key papers and the Fuel Market Issues panel discussion.

Not Available

1993-04-01T23:59:59.000Z

162

Transient injection-locking of an unstable ring dye laser  

SciTech Connect (OSTI)

The transient injection-locking properties of an unstable ring resonator dye laser have been investigated. When a narrow line optical pulse was injected into the ring resonator, the energy emitted from the ring increased and the lasing spectrum narrowed to that of the injected pulse. However, the polarization control of the emitted radiation was incomplete.

Harris, D.G.; Waite, T.R.; Holmes, D.A. (Rockwell International, Rocketdyne Division, Canoga Park, California 91303 (USA))

1990-04-20T23:59:59.000Z

163

Study of CMOS APS Responsivity Enhancement: Ring-Shaped Photodiode  

E-Print Network [OSTI]

Study of CMOS APS Responsivity Enhancement: Ring-Shaped Photodiode Tatiana Danov, Igor Shcherback obtained from various ring-shaped pixel photodiodes with different inner radius, implemented in a standard illumination. We show that the photodiodes with a small ring-opening exhibit better sensitivity in the blue

164

M57 Ring Nebulae M57 -The famously named "Ring Nebula" is located in the northern constellation of Lyra, and  

E-Print Network [OSTI]

M57 ­ Ring Nebulae M57 - The famously named "Ring Nebula" is located in the northern constellation by ultraviolet energy from the central star. _ _ _ _ _ _ Credits: Wikpedia; NASA/SCSTi/AURA #12;

165

A coupled model for ring dynamics, gas flow, and oil flow through the ring grooves in IC engines  

E-Print Network [OSTI]

Oil flows through ring/groove interface play a critical role in oil transport among different regions the piston ring pack of internal combustion engines. This thesis work is intended to improve the understanding and ...

Jia, Ke, S. M. Massachusetts Institute of Technology

2009-01-01T23:59:59.000Z

166

American business cycles and innovation  

E-Print Network [OSTI]

introduces the concepts of innovation and invention. The second section discusses the business cycles and highlights general causes of business cycles. The final section details the history of the iron, steel, aluminum, and pharmaceutical industries...

Hood, Michael

2013-02-22T23:59:59.000Z

167

A LATTICE FOR THE 50 GEV MUON COLLIDER RING.  

SciTech Connect (OSTI)

A resent progress report on the lattice design of the 50-50 GeV muon collider is presented. The ring circumference needs to be as small as possible due to the short lifetime of the 50 GeV muons. The background at the detector is affected by the continuous decay of muons into electrons which requires a dipole between the high focusing quadrupoles and the detector. To obtain a luminosity on the order of 1 x 10{sup 33} cm{sup {minus}2} S{sup {minus}1} it is required to have beam intensities on the order of 1 x 10{sup 12} particles per bunch. The rms momentum spread of the beam is equal to 0.12% and the beta functions at the interaction point are equal to 4 cm. The maxima of the betatron functions at these quadrupoles are 1300 m, resulting in large chromaticities which must be corrected by local chromatic correction. Pairs of horizontal and vertical chromatic sextupoles are located at locations where the corresponding betatron functions are 100 m and the values of the horizontal dispersion functions are 3 and 2 m, respectively. They are carefully placed so that most of their nonlinear effects are canceled. The dynamic aperture is larger than 7 times the mean size of the beam for the momentum offsets larger than {minus}6 and +10 sigmas.

TRBOJEVIC,D.

1998-06-28T23:59:59.000Z

168

A High-Energy Solid State Battery with an Extremely Long Cycle...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Stories Contact Us Index Home | ORNL | Highlights SHARE Functional Materials for Energy A High-Energy Solid State Battery with an Extremely Long Cycle Life October 15, 2014...

169

Mass and Lifetime Measurements in Storage Rings  

SciTech Connect (OSTI)

Masses of nuclides covering a large area of the chart of nuclides can be measured in storage rings where many ions circulate at the same time. In this paper the recent progress in the analysis of Schottky mass spectrometry data is presented as well as the technical improvements leading to higher accuracy for isochronous mass measurements with a time-of-flight detector. The high sensitivity of the Schottky method down to single ions allows to measure lifetimes of nuclides by observing mother and daughter nucleus simultaneously. In this way we investigated the decay of bare and H-like 140Pr. As we could show the lifetime can be even shortened compared to those of atomic nuclei despite of a lower number of electrons available for internal conversion or electron capture.All these techniques will be implemented with further improvements at the storage rings of the new FAIR facility at GSI in the future.

Weick, H.; Beckert, K.; Beller, P.; Bosch, F.; Dimopoulou, C.; Kozhuharov, C.; Kurcewicz, J.; Mazzocco, M.; Nociforo, C.; Nolden, F.; Steck, M.; Sun, B.; Winkler, M. [Gesellschaft fuer Schwerionenforschung mbH, 64291 Darmstadt (Germany); Brandau, C.; Chen, L.; Geissel, H.; Knoebel, R.; Litvinov, S. A.; Litvinov, Yu. A.; Scheidenberger, C. [Gesellschaft fuer Schwerionenforschung mbH, 64291 Darmstadt (Germany); II. Phys. Institut, Justus-Liebig-Universitaet Giessen, 35392 Giessen (Germany)] (and others)

2007-05-22T23:59:59.000Z

170

Monopole-Antimonopole Chains and Vortex Rings  

E-Print Network [OSTI]

We consider static axially symmetric solutions of SU(2) Yang-Mills-Higgs theory. The simplest such solutions represent monopoles, multimonopoles and monopole-antimonopole pairs. In general such solutions are characterized by two integers, the winding number m of their polar angle, and the winding number n of their azimuthal angle. For solutions with n=1 and n=2, the Higgs field vanishes at m isolated points along the symmetry axis, which are associated with the locations of m monopoles and antimonopoles of charge n. These solutions represent chains of m monopoles and antimonopoles in static equilibrium. For larger values of n, totally different configurations arise, where the Higgs field vanishes on one or more rings, centered around the symmetry axis. We discuss the properties of such monopole-antimonopole chains and vortex rings, in particular their energies and magnetic dipole moments, and we study the influence of a finite Higgs self-coupling constant on these solutions.

Burkhard Kleihaus; Jutta Kunz; Yasha Shnir

2004-05-19T23:59:59.000Z

171

Edinburgh Research Explorer Money Cycles  

E-Print Network [OSTI]

Edinburgh Research Explorer Money Cycles Citation for published version: Clausen, A & Strub, C 2014 'Money Cycles' Edinburgh School of Economics Discussion Paper Series. Link: Link to publication record date: 11. Dec. 2014 #12;Edinburgh School of Economics Discussion Paper Series Number 249 Money Cycles

Millar, Andrew J.

172

HEURISTIC SEARCH FOR HAMILTON CYCLES  

E-Print Network [OSTI]

by combining it with the remaining cycles. The following is the description of the main part of the algorithmHEURISTIC SEARCH FOR HAMILTON CYCLES IN CUBIC GRAPHS Janez ALES, Bojan MOHAR and Tomaz PISANSKI. A successful heuristic algorithm for nding Hamilton cycles in cubic graphs is described. Several graphs from

Mohar, Bojan

173

Performance evaluation of bound diamond ring tools  

SciTech Connect (OSTI)

LLNL is collaborating with the Center for Optics Manufacturing (COM) and the American Precision Optics Manufacturers Association (APOMA) to optimize bound diamond ring tools for the spherical generation of high quality optical surfaces. An important element of this work is establishing an experimentally-verified link between tooling properties and workpiece quality indicators such as roughness, subsurface damage and removal rate. In this paper, we report on a standardized methodology for assessing ring tool performance and its preliminary application to a set of commercially-available wheels. Our goals are to (1) assist optics manufacturers (users of the ring tools) in evaluating tools and in assessing their applicability for a given operation, and (2) provide performance feedback to wheel manufacturers to help optimize tooling for the optics industry. Our paper includes measurements of wheel performance for three 2-4 micron diamond bronze-bond wheels that were supplied by different manufacturers to nominally- identical specifications. Preliminary data suggests that the difference in performance levels among the wheels were small.

Piscotty, M.A.; Taylor, J.S.; Blaedel, K.L.

1995-07-14T23:59:59.000Z

174

NuSTORM {\\mu} Ring -- Design and Injection Optimization  

E-Print Network [OSTI]

The design of the NuSTORM muon production beam line and storage ring is discussed. The facility includes a pion production target station with a pion collection horn and transport into a straight section of a storage ring. {\\pi} decay within that straight section provides {\\mu}'s that are stored within the ring for subsequent decay providing precision electron and muon neutrino beams. The ring and transport designs are described and optimized. Genetic Algorithm optimization of the horn and transport into the ring has been performed, providing a significant increase in intensity

Neuffer, David; Bross, A

2015-01-01T23:59:59.000Z

175

GSI Rapid Cycling Magnets Project | Superconducting Magnet Division  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

GSI Rapid Cycling Magnets Project GSI Rapid Cycling Magnets Project While superconducting magnets easily achieve higher magnetic fields at lower cost than conventional electromagnets, it is very difficult to ramp superconducting magnets very quickly. But exactly that is needed at the planned new facility of GSI, the Gesellschaft für Schwerionenforschung (Institute for Heavy Ion Research), in Darmstadt, Germany. In the magnets of the SIS 200 ring, one of the components of the new facility, the magnetic field must be ramped from 0.5 Tesla to 4 Tesla at a rate of 1 Tesla per second. This ramp rate is almost 25 times faster than the ramp rate of the Relativistic Heavy Ion Collider (RHIC) magnets at Brookhaven National Lab (BNL), which ramp at a rate of 0.042 Tesla per second. While the SIS 200 magnets also require a slightly higher field strength than the

176

MULTIPARAMETER OPTIMIZATION STUDIES ON GEOTHERMAL ENERGY CYCLES  

E-Print Network [OSTI]

of Practical Cycles for Geothermal Power Plants." GeneralDesign and Optimize Geothermal Power Cycles." Presented atof Practical Cycles for Geothermal Power Plants." General

Pope, W.L.

2011-01-01T23:59:59.000Z

177

THE TRANSPOSED CRITICAL TEMPERATURE RANKINE THERMODYNAMIC CYCLE  

E-Print Network [OSTI]

Process Program for Geothermal Power Plant Cycles,'*for a Rankine Cycle Geothermal Power Plant," Proceedings,Design and Optimize Geothermal Power Cycles," presented at

Pope, William L.

2012-01-01T23:59:59.000Z

178

n-step cycle inequalities - Optimization Online  

E-Print Network [OSTI]

also introduced the so-called cycle inequalities (called 1-step cycle inequalities in this ...... combination of the cycle detection strategy of Tarjan [16] and the...

2014-07-02T23:59:59.000Z

179

Life-cycle Assessment of Semiconductors  

E-Print Network [OSTI]

life-cycle energy requirements (e total ) and global warmingtotal life-cycle global warming impacts. Chapter 3 Life-cycle Energy and Global

Boyd, Sarah B.

2009-01-01T23:59:59.000Z

180

Frostbite Theater - Liquid Nitrogen Experiments - The Flying Ring!  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Liquid Nitrogen and the Tea Kettle Mystery! Liquid Nitrogen and the Tea Kettle Mystery! Previous Video (Liquid Nitrogen and the Tea Kettle Mystery!) Frostbite Theater Main Index Next Video (Pewter Bells) Pewter Bells The Flying Ring! A copper ring leaps off an electromagnet when it's turned on. What happens when the ring's resistance is lowered using liquid nitrogen? [ Show Transcript ] Announcer: Frostbite Theater presents... Cold Cuts! No baloney! Joanna and Steve: Just science! Joanna: Hi! I'm Joanna! Steve: And I'm Steve! Joanna: And this is an AC powered electromagnet. And this is a copper ring. When I place the copper ring on the electromagnet and turn it on, the magnet's changing magnetic field will induce an electric current in the copper ring. The current in the ring will then create it's own magnetic

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Joining mechanism with stem tension and interlocked compression ring  

DOE Patents [OSTI]

A stem (34) extends from a second part (30) through a hole (28) in a first part (22). A groove (38) around the stem provides a non-threaded contact surface (42) for a ring element (44) around the stem. The ring element exerts an inward force against the non-threaded contact surface at an angle that creates axial tension (T) in the stem, pulling the second part against the first part. The ring element is formed of a material that shrinks relative to the stem by sintering. The ring element may include a split collet (44C) that fits partly into the groove, and a compression ring (44E) around the collet. The non-threaded contact surface and a mating distal surface (48) of the ring element may have conic geometries (64). After shrinkage, the ring element is locked onto the stem.

James, Allister W.; Morrison, Jay A.

2012-09-04T23:59:59.000Z

182

Quantum thermodynamic cooling cycle  

E-Print Network [OSTI]

The quantum-mechanical and thermodynamic properties of a 3-level molecular cooling cycle are derived. An inadequacy of earlier models is rectified in accounting for the spontaneous emission and absorption associated with the coupling to the coherent driving field via an environmental reservoir. This additional coupling need not be dissipative, and can provide a thermal driving force - the quantum analog of classical absorption chillers. The dependence of the maximum attainable cooling rate on temperature, at ultra-low temperatures, is determined and shown to respect the recently-established fundamental bound based on the second and third laws of thermodynamics.

Palao, J P; Gordon, J M; Palao, Jose P.; Kosloff, Ronnie; Gordon, Jeffrey M.

2001-01-01T23:59:59.000Z

183

Quantum thermodynamic cooling cycle  

E-Print Network [OSTI]

The quantum-mechanical and thermodynamic properties of a 3-level molecular cooling cycle are derived. An inadequacy of earlier models is rectified in accounting for the spontaneous emission and absorption associated with the coupling to the coherent driving field via an environmental reservoir. This additional coupling need not be dissipative, and can provide a thermal driving force - the quantum analog of classical absorption chillers. The dependence of the maximum attainable cooling rate on temperature, at ultra-low temperatures, is determined and shown to respect the recently-established fundamental bound based on the second and third laws of thermodynamics.

Jose P. Palao; Ronnie Kosloff; Jeffrey M. Gordon

2001-06-08T23:59:59.000Z

184

Geothermal Life Cycle Calculator  

SciTech Connect (OSTI)

This calculator is a handy tool for interested parties to estimate two key life cycle metrics, fossil energy consumption (Etot) and greenhouse gas emission (ghgtot) ratios, for geothermal electric power production. It is based solely on data developed by Argonne National Laboratory for DOEs Geothermal Technologies office. The calculator permits the user to explore the impact of a range of key geothermal power production parameters, including plant capacity, lifetime, capacity factor, geothermal technology, well numbers and depths, field exploration, and others on the two metrics just mentioned. Estimates of variations in the results are also available to the user.

Sullivan, John

2014-03-11T23:59:59.000Z

185

Accelerating cycle expansions by dynamical conjugacy  

E-Print Network [OSTI]

Periodic orbit theory provides two important functions---the dynamical zeta function and the spectral determinant for the calculation of dynamical averages in a nonlinear system. Their cycle expansions converge rapidly when the system is uniformly hyperbolic but greatly slowed down in the presence of non-hyperbolicity. We find that the slow convergence can be associated with singularities in the natural measure. A properly designed coordinate transformation may remove these singularities and results in a dynamically conjugate system where fast convergence is restored. The technique is successfully demonstrated on several examples of one-dimensional maps and some remaining challenges are discussed.

Ang Gao; Jianbo Xie; Yueheng Lan

2011-06-06T23:59:59.000Z

186

Self-seeding ring optical parametric oscillator  

DOE Patents [OSTI]

An optical parametric oscillator apparatus utilizing self-seeding with an external nanosecond-duration pump source to generate a seed pulse resulting in increased conversion efficiency. An optical parametric oscillator with a ring configuration are combined with a pump that injection seeds the optical parametric oscillator with a nanosecond duration, mJ pulse in the reverse direction as the main pulse. A retroreflecting means outside the cavity injects the seed pulse back into the cavity in the direction of the main pulse to seed the main pulse, resulting in higher conversion efficiency.

Smith, Arlee V. (Albuquerque, NM); Armstrong, Darrell J. (Albuquerque, NM)

2005-12-27T23:59:59.000Z

187

Water mass distribution in cyclonic rings  

E-Print Network [OSTI]

WATER SASS DISTR'-NUT(ON Til Cy'UON I i RL i( S A Thesis NONA M, RTE JANOPAUL Submitted to the Gvsdust CoiieSe of Texas A&N Univetslty Pst'tiel fuifl11meot of the te(N|ltem 1'lt ot the de[ ee of RASTER OP SC1ENCE i)eceml:er 1979 Nv jot Sue... lect: Phy, . ical Ocean Staphy NATRR MASS DTSPRTblJTTON 1N C". CJ. ONTO RTNGS NONA MARIE . TANOPAUL Approved as to style. and content by: (Chairman. of Committee) (Member) I( December 1979 ABS'IRACT Water Mass Distribution in Cyclonic Rings...

Janopaul, Mona Marie

2012-06-07T23:59:59.000Z

188

Open cycle thermoacoustics  

SciTech Connect (OSTI)

A new type of thermodynamic device combining a thermodynamic cycle with the externally applied steady flow of an open thermodynamic process is discussed and experimentally demonstrated. The gas flowing through this device can be heated or cooled in a series of semi-open cyclic steps. The combination of open and cyclic flows makes possible the elimination of some or all of the heat exchangers (with their associated irreversibility). Heat is directly exchanged with the process fluid as it flows through the device when operating as a refrigerator, producing a staging effect that tends to increase First Law thermodynamic efficiency. An open-flow thermoacoustic refrigerator was built to demonstrate this concept. Several approaches are presented that describe the physical characteristics of this device. Tests have been conducted on this refrigerator with good agreement with a proposed theory.

Reid, Robert Stowers

2000-01-01T23:59:59.000Z

189

G Zero and the Cell Cycle  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

G Zero and the Cell Cycle G Zero and the Cell Cycle Name: Frank Location: N/A Country: N/A Date: N/A Question: When a cell "decides" that it does not need to undergo mitosis, but instead, it will just remain an "adult" and accomplish all of its other functions until it "dies," does it then just lock in to its G-2 stage, or is the G-1 stage it's final adult resting place. My recent studies are confusing me about whether the cell is adult and has its correct number of chromosomes in G-1 or in G-2. Replies: A cell does not enter the Gap 2 (G2) stage unless it is definitely going to complete mitosis and cytokinesis. The Synthesis (S) phase is a commitment to cell division. The stage you are referring to is called the G zero state and the cell does not enter the synthesis stage after completing the Gap 1 growth phase (G1), but enters the G0 to proceed with its function. Recently, it has been demonstrated that the G0 may re-enter the cell cycle and move into mitosis with the proper signals.

190

Approximating Artinian Rings by Gorenstein Rings and 3-Standardness of the Maximal Ideal  

E-Print Network [OSTI]

associated to an Artin local ring, called its Gorenstein colength . We study the basic properties and give bounds on this number in this chapter. We extend results due to W. Teter, C.Huneke and A. Vraciu by studying the relation of Gorenstein colength...

Hariharan, Ananthnarayan

2009-07-23T23:59:59.000Z

191

Carbon Cycle 2.0  

Broader source: Energy.gov (indexed) [DOE]

Carbon Cycle 2.0 Carbon Cycle 2.0 Pioneering science for sustainable energy solutions Artificial Photosynthesis Energy Storage Combustion Carbon Capture & Storage Developing World Efficiency Photovoltaics Biofuels Energy Analysis Climate Modeling Carbon Cycle 2.0 is... 1. A vision for * a global energy system integrated with the Earth's natural carbon cycles * an interactive Berkeley Lab environment with a shared sense of purpose 2. A program development plan that will allow us to deepen our capabilities and provide more opportunities to have impact 3. An attempt to integrate our basic research with applications using models of technology deployment constraints 4. Set of internal activities aimed at priming the effort

192

Building Life Cycle Cost Programs  

Broader source: Energy.gov [DOE]

The National Institute of Standards and Technology (NIST) developed the Building Life Cycle Cost (BLCC) Program to provide computational support for the analysis of capital investments in buildings.

193

Minimize Boiler Short Cycling Losses  

Broader source: Energy.gov [DOE]

This tip sheet on minimizing boiler short cycling losses provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

194

Design Considerations for High Energy Electron -- Positron Storage Rings  

DOE R&D Accomplishments [OSTI]

High energy electron-positron storage rings give a way of making a new attack on the most important problems of elementary particle physics. All of us who have worked in the storage ring field designing, building, or using storage rings know this. The importance of that part of storage ring work concerning tests of quantum electrodynamics and mu meson physics is also generally appreciated by the larger physics community. However, I do not think that most of the physicists working tin the elementary particle physics field realize the importance of the contribution that storage ring experiments can make to our understanding of the strongly interacting particles. I would therefore like to spend the next few minutes discussing the sort of things that one can do with storage rings in the strongly interacting particle field.

Richter, B.

1966-11-00T23:59:59.000Z

195

Circumference Correction Chicanes for Damping Rings P. Emma, T. Raubenheimer  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Circumference Correction Chicanes for Circumference Correction Chicanes for Damping Rings P. Emma, T. Raubenheimer August 14,1998 1 Introduction Several large low-emittance damping rings are presently being designed to meet the requirements of future linear colliders. These rings tend to have relatively large circumferences ∼300 m so that they can damp many trains of bunches at the same time. With the large circumference, the path length around the ring may become quite sensitive to thermal and ground motion effects. In addition, most of the rings include damping wigglers whose path length varies with their strength. In e-/e+ storage rings, the beam revolution time is determined by the rf frequency. Thus, a change in the nominal path length will cause a change in both the beam energy and the

196

The Elastohydrodynamic Lubrication of Piston Rings  

Science Journals Connector (OSTI)

...throughout most of the engine cycle, but that a transition to mixed...four-stroke and six two-stroke diesel engines is assessed in terms...is presented to confirm the general findings recorded in the study...liners many times each second in diesel engines, together with the...

1983-01-01T23:59:59.000Z

197

Unicell structure for superconducting storage rings  

SciTech Connect (OSTI)

Mechanically integrated, magnetically decoupled storage rings were designed for a heavy ion collider for 100 GeV/amu Au, at B = 2.7T. New concepts were developed, including detailed engineering design and cost estimates. A ''unicell'' contains a half-cell of both rings within a single He vessel. The unicell design is optimized for economical mass production. Survey pads welded to the laminations provide external fiducials to locate the magnet cores. Roller bearing self aligning supports accommodate cool-down shrinkage. The design tolerates relative motion of components resulting from longitudinal shrinkage in the approx.15 m long unicell without affecting performance. Magnetic and physical lengths are the same, eliminating waste space. ''Achromatic'' quadrupoles with sextupoles at both ends are located on a common precision beam tube which aligns and supports a pick-up electrode. The unicell accommodates longer dipoles compared to conventional designs, reducing B/sub max/, stored energy, and the volume of iron and superconductor. Applications to future machines will be discussed.

Danby, G.; DeVito, B.; Jackson, J.; Keohane, G.; Lee, Y.Y.; Phillips, R.; Plate, S.; Repeta, L.; Skaritka, J.; Smith, L.

1985-01-01T23:59:59.000Z

198

Virtuous Cycle Cycles of activity and software projects  

E-Print Network [OSTI]

Inspection #12;Programming Cycle - single bug Selected Bug Shared Code Fix Bug Continuous Integration ~8 cycle cvscheck compilation style checking testing javadocs documentation jumble quality of unit testing #12;NetValue Development cvscheck - Source Code Control and Build Shared Centralized Automatic

Pfahringer, Bernhard

199

MUON STORAGE RINGS FOR 6D PHASE SPACE COOLING.  

SciTech Connect (OSTI)

We describe several storage ring designs for reducing the 6-dimensional phase space of circulating muon beams. These rings utilize quadrupole and dipole magnets as well as wedge-shaped, liquid-hydrogen, energy-loss absorbers and energy compensating rf cavities. We obtain evaluations of their cooling performance by particle tracking simulation. Such rings are potentially useful for future Neutrino Factories or Muon Colliders as well as for existing facilities in which cooled, intense muon beams could enhance their physics programs.

KIRK,H.CLINE,D.FUKUI,Y.GARREN,A.

2003-05-12T23:59:59.000Z

200

Excitation energy dependence of the exciton inner ring  

Science Journals Connector (OSTI)

We report on the excitation energy dependence of the inner ring in the exciton emission pattern. The contrast of the inner ring is found to decrease with lowering excitation energy. Excitation by light tuned to the direct exciton resonance is found to effectively suppress excitation-induced heating of indirect excitons and facilitate the realization of a cold and dense exciton gas. The excitation energy dependence of the inner ring is explained in terms of exciton transport and cooling.

Y. Y. Kuznetsova, J. R. Leonard, L. V. Butov, J. Wilkes, E. A. Muljarov, K. L. Campman, and A. C. Gossard

2012-04-30T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

A Compact Ring Design with Tunable Momentum Compaction  

SciTech Connect (OSTI)

A storage ring with tunable momentum compaction has the advantage in achieving different RMS bunch length with similar RF capacity, which is potentially useful for many applications, such as linear collider damping ring and predamping ring where injected beam has a large energy spread and a large transverse emittance. A tunable bunch length also makes the commissioning and fine tuning easier in manipulating the single bunch instabilities. In this paper, a compact ring design based on a supercell is presented, which achieves a tunable momentum compaction while maintaining a large dynamic aperture.

Sun, Y.; /SLAC; ,

2012-05-17T23:59:59.000Z

202

Electronically tunable active antenna using microstrip annular ring  

E-Print Network [OSTI]

&M University Chair oi' Advisory Committee: Dr. Kai Chang The use of the annular ring antenna as an active antenna. element was investi- gated. A circuit model of the antenna derived by considering the annular ring antenna, as s, radial transmission line... antenna. 13 16 10 The annular ring antenna, modeled as radial transmission lines snd load admit tances. 19 11 The complete circuit model of the annular ring antenna. 22 12 Flow chart of the input impedance program. . 13 Input impedance of the TMrz...

Miller, Richard Earl

2012-06-07T23:59:59.000Z

203

Power Series Over Noetherian Rings May 10, 2010 William Heinzer ...  

E-Print Network [OSTI]

May 10, 2010 ... ian rings and of the induced spectral maps associated with various ..... R1. [81, pages 112-118], the proof of the Noetherian property took.

1911-00-51T23:59:59.000Z

204

Formation Mechanism and Low-Temperature Instability of Exciton Rings  

Science Journals Connector (OSTI)

The macroscopic rings observed in the photoluminescence patterns of excitons in coupled quantum wells are explained by a mechanism of carrier imbalance, transport, and recombination. The rings originate from the spatial separation of p and n carriers, and occur at the interface of the p and n domains, where excitons are generated. We explore the states of excitons in the ring over a range of temperatures down to 380???mK and report a transition of the ring into a periodic array of aggregates, a new low-temperature ordered exciton state.

L. V. Butov, L. S. Levitov, A. V. Mintsev, B. D. Simons, A. C. Gossard, and D. S. Chemla

2004-03-18T23:59:59.000Z

205

UAL-BASED SIMULATION ENVIRONMENT FOR SPALLATION NEUTRON SOURCE RING.  

SciTech Connect (OSTI)

This paper outlines the major activities and applications of the Unified Accelerator Library environment for the Spallation Neutron Source (SNS) Ring.

MALITSKY,N.; SMITH,J.; WEI,J.

1999-03-29T23:59:59.000Z

206

Structure of rings in vitreous SiO2  

Science Journals Connector (OSTI)

The structure of n-fold rings in vitreous SiO2 is investigated using molecular-dynamics configurations. A recently developed interaction potential for SiO2 consisting of long-range Coulomb interactions, the effect of electronic polarizability, and three-body covalent forces is used in the molecular-dynamics study of the vitreous state. Results for the statistics of rings and distribution of interatomic distances and bond angles in the rings are presented for the vitreous state. The statistics of rings for the molten state is also discussed.

Jos P. Rino; Ingvar Ebbsj; Rajiv K. Kalia; Aiichiro Nakano; Priya Vashishta

1993-02-01T23:59:59.000Z

207

SpRING: Sparse Reconstruction of Images using the Nullspace method and GRAPPA D. S. Weller1  

E-Print Network [OSTI]

SpRING: Sparse Reconstruction of Images using the Nullspace method and GRAPPA D. S. Weller1 , J. R across coil sensitivities to undo coherent aliasing in undersampled data, at the expense of noise presented in [5] is improved using the mixed 1/2-norm simultaneous sparsity (over P coils) penalty function

Goyal, Vivek K

208

Life Cycle Asset Management  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

(The following directives are deleted or consolidated into this Order and shall be phased out as noted in Paragraph 2: DOE 1332.1A; DOE 4010.1A; DOE 4300.1C; DOE 4320.1B; DOE 4320.2A; DOE 4330.4B; DOE 4330.5; DOE 4540.1C; DOE 4700.1). This Order supersedes specific project management provisions within DOE O 430.1A, LIFE CYCLE ASSET MANAGEMENT. The specific paragraphs canceled by this Order are 6e(7); 7a(3); 7b(11) and (14); 7c(4),(6),(7),(11), and (16); 7d(4) and (8); 7e(3),(10), and (17); Attachment 1, Definitions (item 30 - Line Item Project, item 42 - Project, item 48 - Strategic System); and Attachment 2, Contractor Requirements Document (paragraph 1d regarding a project management system). The remainder of DOE O 430.1A remains in effect. Cancels DOE O 430.1. Canceled by DOE O 413.3.

1998-10-14T23:59:59.000Z

209

Natural Gas Combined Cycle  

E-Print Network [OSTI]

The Coal Ash Corrosion Resistant Materials Testing Program is being conducted by B&W at Reliant Energys Niles plant in Niles, Ohio. The total estimated cost of $1,864,603 is co-funded by DOE contributing 37.5%, OCDO providing 33.3 % and B&W providing 17%. The remaining 12 % is in-kind contributions by Reliant Energy and tubing suppliers. Materials development is important to the power industry, and to the use of coal. Figure 1 compares the cost of electricity for subcritical and supercritical coal-fired plants with a natural gas combined cycle (NGCC) plant based on an 85 % capacity factor. This shows that at $1.20/MBtu for fuel, coal is competitive with NGCC when gas is at $3.40/MBtu or higher. An 85 % capacity factor is realistic for a coal-fired plant, but NGCC plants are currently only achieving about 60%. This gives coal an advantage if compared on the basis of cost per kW generated per year. When subcritical and supercritical plants are compared,

Dennis K. Mcdonald; Subcritical Coal Plant; Supercritical Coal Plant

210

Biomass Gasification Combined Cycle  

SciTech Connect (OSTI)

Gasification combined cycle continues to represent an important defining technology area for the forest products industry. The ''Forest Products Gasification Initiative'', organized under the Industry's Agenda 2020 technology vision and supported by the DOE ''Industries of the Future'' program, is well positioned to guide these technologies to commercial success within a five-to ten-year timeframe given supportive federal budgets and public policy. Commercial success will result in significant environmental and renewable energy goals that are shared by the Industry and the Nation. The Battelle/FERCO LIVG technology, which is the technology of choice for the application reported here, remains of high interest due to characteristics that make it well suited for integration with the infrastructure of a pulp production facility. The capital cost, operating economics and long-term demonstration of this technology area key input to future economically sustainable projects and must be verified by the 200 BDT/day demonstration facility currently operating in Burlington, Vermont. The New Bern application that was the initial objective of this project is not currently economically viable and will not be implemented at this time due to several changes at and around the mill which have occurred since the inception of the project in 1995. The analysis shows that for this technology, and likely other gasification technologies as well, the first few installations will require unique circumstances, or supportive public policies, or both to attract host sites and investors.

Judith A. Kieffer

2000-07-01T23:59:59.000Z

211

Nuclear fuel cycle information workshop  

SciTech Connect (OSTI)

This overview of the nuclear fuel cycle is divided into three parts. First, is a brief discussion of the basic principles of how nuclear reactors work; second, is a look at the major types of nuclear reactors being used and world-wide nuclear capacity; and third, is an overview of the nuclear fuel cycle and the present industrial capability in the US.

Not Available

1983-01-01T23:59:59.000Z

212

Working fluid for Rankine cycle  

SciTech Connect (OSTI)

A Rankine cycle working fluid is disclosed containing a mixture of 2,2,3,3tetrafluoropropanol and water, which is low toxic, incombustible, nonexplosive, noncorrosive and stable, and also has a high critical temperature and forms azeotropic-like composition. It is suited for use in a rankine cycle using heat source of low temperature.

Aomi, H.; Enjo, N.

1980-11-11T23:59:59.000Z

213

Extreme Financial cycles$ B. Candelonb,  

E-Print Network [OSTI]

Extreme Financial cycles$ B. Candelonb, , G. Gauliera , C. Hurlinb aUniversity Maastricht proposes a new approach to date extreme financial cycles. Elabo- rating on recent methods in extreme value theory, it elaborates an extension of the famous calculus rule to detect extreme peaks and troughs

Paris-Sud XI, Université de

214

Reading Comprehension - The Water Cycle  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

The Water Cycle The Water Cycle Evaporation, Condensation and Precipitation The _________ moon sun water clouds evaporates _________ fish oceans rain water from lakes and oceans. As the air rises, it cools. The water vapor condenses into tiny droplets of _________ evaporation clouds water sunshine . The droplets crowd together and form a _________ cloud lake storm precipitation . Wind blows the _________ rain sun droplet cloud towards the land. The tiny droplets join together and fall as precipitation to the _________ river lake ground cloud . The water soaks into the ground and collects in _________ rivers and lakes oceans and clouds jars and cups plants and animals . The _________ storm cycle river house that never ends has started again! A water cycle diagram. Use the diagram to identify the different parts of the water cycle:

215

CMVRTC: Heavy Truck Duty Cycle  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

heavy truck duty cycle (HTDC) project heavy truck duty cycle (HTDC) project OVERVIEW The Heavy Truck Duty Cycle (HTDC) Project was initiated in 2004 and is sponsored by the US Department of Energy's (DOE's) Office of FreedomCar and Vehicle Technologies Program. ORNL designed the research program to generate real-world-based duty cycle data from trucks operating in long-haul operations and was designed to be conducted in three phases: identification of parameters to be collected, instrumentation and pilot testing, identification of a real-world fleet, design of the data collection suite and fleet instrumentation, and data collection, analysis, and development of a duty cycle generation tool (DCGT). ANL logo dana logo michelin logo Schrader logo This type of data will be useful for supporting energy efficiency

216

Fuel cycle cost uncertainty from nuclear fuel cycle comparison  

SciTech Connect (OSTI)

This paper examined the uncertainty in fuel cycle cost (FCC) calculation by considering both model and parameter uncertainty. Four different fuel cycle options were compared in the analysis including the once-through cycle (OT), the DUPIC cycle, the MOX cycle and a closed fuel cycle with fast reactors (FR). The model uncertainty was addressed by using three different FCC modeling approaches with and without the time value of money consideration. The relative ratios of FCC in comparison to OT did not change much by using different modeling approaches. This observation was consistent with the results of the sensitivity study for the discount rate. Two different sets of data with uncertainty range of unit costs were used to address the parameter uncertainty of the FCC calculation. The sensitivity study showed that the dominating contributor to the total variance of FCC is the uranium price. In general, the FCC of OT was found to be the lowest followed by FR, MOX, and DUPIC. But depending on the uranium price, the FR cycle was found to have lower FCC over OT. The reprocessing cost was also found to have a major impact on FCC.

Li, J.; McNelis, D. [Institute for the Environment, University of North Carolina, Chapel Hill (United States); Yim, M.S. [Department of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology (Korea, Republic of)

2013-07-01T23:59:59.000Z

217

Characterization of cycle-to-cycle variations in a natural gas spark ignition engine  

Science Journals Connector (OSTI)

Abstract In this work a study of the influence of the fuel/air equivalence ratio and engine rotational speed on the cycle-to-cycle variations in combustion in a natural gas spark ignition engine is presented. The study considers both classic estimators of cyclic dispersion and a new one, based on the burned mass and burning rate. The engine experimental conditions were as follows: Intake pressure 0.5bar, while fuel/air equivalence ratio was changed from 1.0 to 0.63, and engine rotational speed was varied from 1000rpm to 2500rpm. For each equivalence ratio and engine speed, a diagnosis model is used to process the experimentally obtained combustion pressure data in order to provide combustion relevant results such as the mass burning rate at a cycle level. A procedure based on the use of genetic algorithms is used to obtain a very accurate and objective (without human intervention) adjustment of the optimum parameters needed for combustion diagnosis: angular positioning and pressure offset of the pressure register, dynamic compression ratio, and heat transfer coefficients. The model allows making the diagnosis of series of 830 consecutive engine cycles in an automatic way, increasing the objectivity of the combustion diagnosis. The paper focuses on using the values of the mass fraction burned computed from the pressure register and especially on the analysis of the combustion cycle to cycle variation in the natural gas fuelled engine. A new indicator for the study of cycle-to-cycle variations is proposed, i.e. the standard deviation of the mass fraction burning rate. The values of this new indicator are compared with other classic indicators, showing the same general trends. However, a deeper insight is provided on the combustion cyclic variation when the values of the new indicator are plotted as a function of the mass fraction burned, since this allows analyzing the cyclic variation along the combustion development in each cycle from a mass fraction burned of zero to one, with a relevant value at mass fraction burned of 0.5. More important is that the consideration of the dependence of the combustion variables (density, flame front surface, combustion speed) on the mass fraction burned allows ensemble averaging of all registered cycles for each value of mass fraction burned. This permits using the ensemble averaged mass fraction burning rate as an estimator of combustion speed. The analysis of the general trends of cyclic dispersion when engine speed and equivalence ratio are modified (1000, 1750 and 2500rpm; 0.7, 0.8, 0.9 and 1.0) indicate that cycle-to-cycle variations show, as expected, a strong dependence on the engine rotational speed, increasing the variation with engine rpm. However, when the standard deviation of mass fraction burning rate is plotted as a function of mass fraction burned, there is a linear dependence on engine rpm, but only a very weak dependence on equivalence ratio. This means that the proposed estimator of cyclic dispersion is sensitive to only flow turbulent intensity and not to equivalence ratio.

M. Reyes; F.V. Tinaut; B. Gimnez; A. Prez

2015-01-01T23:59:59.000Z

218

Quantum codes over Finite Frobenius Rings  

E-Print Network [OSTI]

polynomial rX i=1 aiX r i where ai 2 Z=(p n). Let = exp(2 i=pn) then, (a) = a is a generating character. 2. Inner product Symplectic inner product Let (ajb) and (a 0 jb 0 ) denote two codewords in the code C. Then the symplectic inner product... of the two vectors is de ned as (b:a 0 b 0 :a). If C is the code then its dual C? is de ned as C? = f(ajb)j (b:a0 b0:a) = 1forall(a0jb0) 2 Cg Lemma 1 Let be a character of a nite frobenius ring R. Then is a right generating character if and only...

Sarma, Anurupa

2012-10-19T23:59:59.000Z

219

Introductory statistical mechanics for electron storage rings  

SciTech Connect (OSTI)

These lectures introduce the beam dynamics of electron-positron storage rings with particular emphasis on the effects due to synchrotron radiation. They differ from most other introductions in their systematic use of the physical principles and mathematical techniques of the non-equilibrium statistical mechanics of fluctuating dynamical systems. A self-contained exposition of the necessary topics from this field is included. Throughout the development, a Hamiltonian description of the effects of the externally applied fields is maintained in order to preserve the links with other lectures on beam dynamics and to show clearly the extent to which electron dynamics in non-Hamiltonian. The statistical mechanical framework is extended to a discussion of the conceptual foundations of the treatment of collective effects through the Vlasov equation.

Jowett, J.M.

1986-07-01T23:59:59.000Z

220

Near-rings of group mappings  

E-Print Network [OSTI]

)[ = m we have A f(v ) 1 1 1 1 f(v ) and m is minimal with this property. On the other hand f(v ) = f(Av ) = A f(v ) =AA f(v ) = A f(v), which implies r=O. 1 1 1 1 1 Conversely, suppose m divides n and choose v 6 6 , v 6 8 Define f:G ~ G by f(0) = 0..., f(A v ) = A v , j = 1, 2, . . . , n and f(v) = 0 otherwise. Since m divides n, f is well defined, and clearly f E C(A). Let H be an additive subgroup of the near-ring N. We say H is N-invariant if NH c H and HN c H. Lemma 1. 2: [5] Let H be a C...

Galli, John C

2012-06-07T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

EVALUATING SPARSITY PENALTY FUNCTIONS FOR COMBINED COMPRESSED SENSING AND PARALLEL MRI  

E-Print Network [OSTI]

in the particular choice of function used to promote sparsity. Having developed SpRING, a framework for combining CS appropriately choosing the penalty function has on the performance of SpRING. These experiments demonstrate, and the undersampling is incoherent enough for the desired number of ob- servations. Since the spatial coil weighting

Goyal, Vivek K

222

ESTR -Energy Saving Token Ring Protocol for Wireless Sensor Networks  

E-Print Network [OSTI]

ESTR - Energy Saving Token Ring Protocol for Wireless Sensor Networks Faruk Bagci, Theo Ungerer a long lifetime of the sensor network and the application it is important to save energy. A sensor node control (MAC) protocol for wireless sensor networks, called Energy Saving Token Ring Protocol (ESTR). ESTR

Ungerer, Theo

223

Updating the Tyrol tree-ring dataset , U. Bntgen1  

E-Print Network [OSTI]

Updating the Tyrol tree-ring dataset J. Esper1 , U. Büntgen1 , D. Frank1 , T. Pichler2 , K in palaeoclimatology The Tyrol dataset is a collection of 71 Picea abies ring width measurement series from the study area in Tyrol in the central Alps. We here describe efforts of updating this relevant dataset

Nicolussi, Kurt

224

Drop Tests of the Closure Ring for the 9975 Package  

SciTech Connect (OSTI)

The drop tests of the closure ring for 9975 packages, described here, were performed to answer questions raised by the regulatory authority as a result of deformation of the closure ring and drum rim observed during drop tests conducted in September 1998.

Smith, A.C

1999-09-29T23:59:59.000Z

225

Magnetic properties of small multi-layered rings  

E-Print Network [OSTI]

Thin film rings can be an alternative geometry of magnetic memory cells, in which data bits are stored by the chirality of the flux-closed or 'vortex' state of the ring. The absence of the stray field in the vortex state ...

Jung, Wonjoon

2007-01-01T23:59:59.000Z

226

Design and Evaluation of Hierarchical Rings with Deflection Routing  

E-Print Network [OSTI]

that enable us to mostly maintain the simplicity of traditional simple ring topologies while providing higher of several MUXes to allow traffic to enter and leave, and one pipeline register. Its latency is typically and commercial multicore processors have utilized ring

Mutlu, Onur

227

Regular ring dynamics in AX2 tetrahedral glasses  

Science Journals Connector (OSTI)

We review the experimental evidence and qualitative arguments for the existence of small highly regular rings of bonds in amorphous (a-)SiO2 and selected other AX2 tetrahedral glasses. The structure and vibrations of planar 3-rings and regular puckered 4-rings in a-SiO2 are then modeled using Born central and noncentral forces. The vibrational coupling of these rings to the more disordered glass network is modeled by attaching a Bethe lattice at each connection. The calculated vibrational properties of the breathing modes of the rings are found to be quite consistent with the observed frequencies, linewidths, and isotope shifts of the sharp lines D1 and D2 seen in the Raman spectra of a-SiO2. The results support the previous assignment of D2 (606 cm-1) to a planar 3-ring and D1 (495 cm-1) to a regular ring. Similar calculations for a-GeO2 are consistent with the suggestion that this material contains a substantial concentration of nearly planar 3-rings. Our methods can be generalized to treat similar forms of intermediate range order in glasses having other network connectivities.

R. A. Barrio; F. L. Galeener; E. Martnez; R. J. Elliott

1993-12-01T23:59:59.000Z

228

Recent Progress at the Photon Factory Storage Ring  

SciTech Connect (OSTI)

The present status of the Photon Factory storage ring (PF ring) at High Energy Accelerator Research Organization (KEK), including recent progress for the machine developments, is reported. Due to the establishment of the simultaneous injection to the three rings (PF, HER, LER) from the KEK injector linac since April 2009, the PF ring currently operates almost all the time in a top-up mode available to users at a stored current of 450 mA in multi-bunch mode, and at a stored current of 51 mA in single-bunch mode, except the time while the KEK linac injection to the PF-AR twice daily. The third in-vacuum short gap undulator was installed at PF ring in September 2009.

Miyauchi, Hiroshi [Photon Factory, High Energy Accelerator Research Organization, KEK, Oho, Tsukuba, Ibaraki 305-0801 (Japan)

2010-06-23T23:59:59.000Z

229

Superposition states of ultracold bosons in rotating rings with a realistic potential barrier  

SciTech Connect (OSTI)

In a recent paper [Phys. Rev. A 82, 063623 (2010)] Hallwood et al. argued that it is feasible to create large superposition states with strongly interacting bosons in rotating rings. Here we investigate in detail how the superposition states in rotating-ring lattices depend on interaction strength and barrier height. With respect to the latter we find a trade-off between energy gap and quality of the superposition state. Most importantly, we go beyond the {delta}-function approximation for the barrier potential and show that the energy gap decreases exponentially with the number of particles for weak barrier potentials of finite width. These are crucial issues in the design of experiments to realize superposition states.

Nunnenkamp, Andreas; Rey, Ana Maria; Burnett, Keith [Departments of Physics and Applied Physics, Yale University, New Haven, Connecticut 06520 (United States); JILA, NIST and Department of Physics, University of Colorado, Boulder, Colorado 80309 (United States); University of Sheffield, Firth Court, Western Bank, Sheffield, S10 2TN (United Kingdom)

2011-11-15T23:59:59.000Z

230

Star clusters in a nuclear star-forming ring: The disappearing string of pearls  

E-Print Network [OSTI]

An analysis of the star cluster population in a low-luminosity early type galaxy, NGC 2328, is presented. The clusters are found in a tight star-forming nuclear spiral/ring pattern and we also identify a bar from structural 2D decomposition. These massive clusters are forming very efficiently in the circum-nuclear environment, they are young, possibly all less than 30 Myr of age. The clusters indicate an azimuthal age gradient, consistent with a "pearls-on-a-string" formation scenario suggesting bar driven gas inflow. The cluster mass function has a robust down-turn at low masses at all age bins. Assuming clusters are born with a power-law distribution, this indicates extremely rapid disruption at time-scales of just several Myr. If found to be typical, it means that clusters born in dense circum-nuclear rings do not survive to become old globular clusters in non-interacting systems.

Vaisanen, Petri; Randriamanakoto, Zara

2014-01-01T23:59:59.000Z

231

SUMMARY ON TITANIUM NITRIDE COATING OF SNS RING VACUUM CHAMBERS.  

SciTech Connect (OSTI)

The inner surfaces of the 248 m Spallation Neutron Source (SNS) accumulator ring vacuum chambers are coated with {approx}100nm of titanium nitride (TiN) to reduce the secondary electron yield (SEY) of the chamber walls. There are approximately 135 chambers and kicker modules, some up to 5m in length and 36cm in diameter, coated with TiN. The coating is deposited by means of reactive DC magnetron sputtering -using a - cylindrical cathode with internal permanent magnets. This cathode configuration generates a deposition-rate sufficient to meet the required production schedule and produces stoichiometric films with good adhesion, low SEY and acceptable outgassing. Moreover, the cathode magnet configuration allows for simple changes in length and has been adapted to coat the wide variety of chambers and components contained within the arcs, injection, extraction, collimation and RF straight sections. Chamber types and quantities as well as the cathode configurations are presented herein. The unique coating requirements of the injection kicker ceramic chambers and the extraction kicker ferrite surface will be emphasized. A brief summary of the salient coating properties is given including the interdependence of SEY as a function of surface roughness and its effect on outgassing.

TODD, R.; HE, P.; HSEUH, H.C.; WEISS, D.

2005-05-16T23:59:59.000Z

232

Storage ring lattice calibration using resonant spin depolarization  

DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

This paper presents measurements of the GeV-scale electron beam energy for the storage rings at the synchrotron light source facilities Australian Synchrotron (AS) and SPEAR3 at SLAC. Resonant spin depolarization was employed in the beam energy measurement, since it is presently the highest precision technique and an uncertainty of order 10?6 was achieved at SPEAR3 and AS. Using the resonant depolarization technique, the beam energy was measured at various rf frequencies to measure the linear momentum compaction factor. This measured linear momentum compaction factor was used to evaluate models of the beam trajectory through combined-function bending magnets. The main bending magnets of both lattices are rectangular, horizontally defocusing gradient bending magnets. Four modeling approaches are compared for the beam trajectory through the bending magnet: a circular trajectory, linear and nonlinear hyperbolic cosine trajectories, and numerical evaluation of the trajectory through the measured magnetic field map. Within the uncertainty of the measurement the momentum compaction factor is shown to agree with the numerical model of the trajectory within the bending magnet, and disagree with the hyperbolic cosine approximation.

Wootton, K. P.; Boland, M. J.; Corbett, W. J.; Huang, X.; LeBlanc, G. S.; Lundin, M.; Panopoulos, H. P.; Safranek, J. A.; Tan, Y.-R. E.; Taylor, G. N.; Tian, K.; Rassool, R. P.

2013-07-01T23:59:59.000Z

233

CMVRTC: Medium Truck Duty Cycle  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

medium truck duty cycle (MTdc) project medium truck duty cycle (MTdc) project OVERVIEW The Medium Truck Duty Cycle (MTDC) project involves efforts to collect, analyze and archive data related to medium-truck operations in real-world driving environments. Such data and information will be useful to support technology evaluation efforts and to provide a means of accounting for real-world driving performance within medium-class truck analyses. The project involves private industry partners from various truck vocations. The MTDC project is unique in that there currently does not exist a national database of characteristic duty cycles for medium trucks. This project involves the collection of data from multiple vocations (four vocations) and multiple vehicles within these vocations (three vehicles per

234

Minimize Boiler Short Cycling Losses  

SciTech Connect (OSTI)

This revised ITP tip sheet on minimizing boiler short cycling losses provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

Not Available

2006-01-01T23:59:59.000Z

235

THE TRANSPOSED CRITICAL TEMPERATURE RANKINE THERMODYNAMIC CYCLE  

E-Print Network [OSTI]

Combined Diesel-Organic Rankine Cycle Power Plant", in25OoC) closed simple organic Rankine cycle geothermal powerthe simple closed organic Rankine cycle for a given set of

Pope, William L.

2012-01-01T23:59:59.000Z

236

Sustainability Features of Nuclear Fuel Cycle Options  

E-Print Network [OSTI]

The nuclear fuel cycle is the series of stages that nuclear fuel materials go through in a cradle to grave framework. The Once Through Cycle (OTC) is the current fuel cycle implemented in the United States; in which an ...

Passerini, Stefano

237

Response Surface Energy Modeling of an Electric Vehicle over a Reduced Composite Drive Cycle  

SciTech Connect (OSTI)

Response surface methodology (RSM) techniques were applied to develop a predictive model of electric vehicle (EV) energy consumption over the Environmental Protection Agency's (EPA) standardized drive cycles. The model is based on measurements from a synthetic composite drive cycle. The synthetic drive cycle is a minimized statistical composite of the standardized urban (UDDS), highway (HWFET), and US06 cycles. The composite synthetic drive cycle is 20 minutes in length thereby reducing testing time of the three standard EPA cycles by over 55%. Vehicle speed and acceleration were used as model inputs for a third order least squared regression model predicting vehicle battery power output as a function of the drive cycle. The approach reduced three cycles and 46 minutes of drive time to a single test of 20 minutes. Application of response surface modeling to the synthetic drive cycle is shown to predict energy consumption of the three EPA cycles within 2.6% of the actual measured values. Additionally, the response model may be used to predict energy consumption of any cycle within the speed/acceleration envelope of the synthetic cycle. This technique results in reducing test time, which additionally provides a model that may be used to expand the analysis and understanding of the vehicle under consideration.

Jehlik, Forrest [Argonne National Laboratory (ANL)] [Argonne National Laboratory (ANL); LaClair, Tim J [ORNL] [ORNL

2014-01-01T23:59:59.000Z

238

VISCOSITY IN PLANETARY RINGS WITH SPINNING SELF-GRAVITATING PARTICLES  

SciTech Connect (OSTI)

Using local N-body simulation, we examine viscosity in self-gravitating planetary rings. We investigate the dependence of viscosity on various parameters in detail, including the effects of particle surface friction. In the case of self-gravitating rings with low optical depth, viscosity is determined by particle random velocity. Inclusion of surface friction slightly reduces both random velocity and viscosity when particle random velocity is determined by inelastic collisions, while surface friction slightly increases viscosity when gravitational encounters play a major role in particle velocity evolution, so that viscous heating balances with increased energy dissipation at collisions due to surface friction. We find that including surface friction changes viscosity in dilute rings up to a factor of about two. In the case of self-gravitating dense rings, viscosity is significantly increased due to the effects of gravitational wakes, and we find that varying restitution coefficients also change viscosity in such dense rings by a factor of about two. We confirm that our numerical results for viscosity in dense rings with gravitational wakes can be well approximated by a semianalytic expression that is consistent with a previously obtained formula. However, we find that this formula seems to overestimate viscosity in dense rings far from the central planet, where temporary gravitational aggregates form. We derive semianalytic expressions that reproduce our numerical results well for the entire range of examined parameters.

Yasui, Yuki; Ohtsuki, Keiji [Department of Earth and Planetary Sciences, Kobe University, Kobe 657-8501 (Japan); Daisaka, Hiroshi [Graduate School of Commerce and Management, Hitotsubashi University, Tokyo 186-8601 (Japan)

2012-05-15T23:59:59.000Z

239

Population differentiation in tree-ring growth response of white fir (Abies concolor) to climate: Implications for predicting forest responses to climate change  

SciTech Connect (OSTI)

Forest succession models and correlative models have predicted 200--650 kilometer shifts in the geographic range of temperate forests and forest species as one response to global climate change. Few studies have investigated whether population differences may effect the response of forest species to climate change. This study examines differences in tree-ring growth, and in the phenotypic plasticity of tree-ring growth in 16-year old white fir, Abies concolor, from ten populations grown in four common gardens in the Sierra Nevada of California. For each population, tree-ring growth was modelled as a function of precipitation and degree-day sums. Tree-ring growth under three scenarios of doubled C0{sub 2} climates was estimated.

Jensen, D.B.

1993-10-01T23:59:59.000Z

240

Electron Cloud Generation and Trapping in a Quadrupole Magnet at the Los Alamos Proton Storage Ring  

SciTech Connect (OSTI)

Recent beam physics studies on the two-stream e-p instability at the LANL proton storage ring (PSR) have focused on the role of the electron cloud generated in quadrupole magnets where primary electrons, which seed beam-induced multipacting, are expected to be largest due to grazing angle losses from the beam halo. A new diagnostic to measure electron cloud formation and trapping in a quadrupole magnet has been developed, installed, and successfully tested at PSR. Beam studies using this diagnostic show that the 'prompt' electron flux striking the wall in a quadrupole is comparable to the prompt signal in the adjacent drift space. In addition, the 'swept' electron signal, obtained using the sweeping feature of the diagnostic after the beam was extracted from the ring, was larger than expected and decayed slowly with an exponential time constant of 50 to 100 {micro}s. Other measurements include the cumulative energy spectra of prompt electrons and the variation of both prompt and swept electron signals with beam intensity. Experimental results were also obtained which suggest that a good fraction of the electrons observed in the adjacent drift space for the typical beam conditions in the 2006 run cycle were seeded by electrons ejected from the quadrupole.

Macek, Robert J.; Browman, Andrew A.; Ledford, John E.; /TechSource, Santa Fe /Los Alamos; Borden, Michael J.; O'Hara, James F.; McCrady, Rodney C.; Rybarcyk, Lawrence J.; Spickermann, Thomas; Zaugg, Thomas J.; /Los Alamos; Pivi, Mauro T.F.; /SLAC

2008-03-17T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

E-Print Network 3.0 - adult baltic ringed Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

baltic ringed Page: << < 1 2 3 4 5 > >> 1 Baltic Sea Environment Proceedings No. 111 Climate Change in Summary: , Finland. Baltic ringed seal pup in collapsed nest. ISSN...

242

Metallic nanoparticle on micro ring resonator for bio optical detection and sensing  

Science Journals Connector (OSTI)

We have numerically investigated the unique effects of metallic nanoparticle on the ring resonator, especially multiple Au nanoparticles on the micro ring resonator with the 4-port...

Haddadpour, Ali; Yi, Yasha

2010-01-01T23:59:59.000Z

243

E-Print Network 3.0 - accelerated vortex ring Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

left behind... forces were derived from the vortex rings, assuming all propulsive energy to be compiled in the rings... , ending up in a separate vortex ... Source:...

244

Trivial extensions of local rings and a conjecture of  

E-Print Network [OSTI]

Abstract. This paper partly settles a conjecture of Costa on (n,d)-rings, i.e., rings in which n-presented modules have projective dimension at most d. For this purpose, a theorem studies the transfer of the (n,d)-property to trivial extensions of local rings by their residue fields. It concludes with a brief discussion-backed by original examples- of the scopes and limits of our results. This project has been funded by King Fahd University of Petroleum & minerals under

S. Kabbaj; N. Mahdou

2003-01-01T23:59:59.000Z

245

Geodesic Motion in the (Charged) Doubly Spinning Black Ring Spacetime  

E-Print Network [OSTI]

In this article we analyze the geodesics of test particles and light in the five dimensional (charged) doubly spinning black ring spacetime. Apparently it is not possible to separate the Hamilton-Jacobi-equation for (charged) doubly spinning black rings in general, so we concentrate on special cases: null geodesics in the ergosphere and geodesics on the two rotational axes of the (charged) doubly spinning black ring. We present analytical solutions to the geodesic equations for these special cases. Using effective potential techniques we study the motion of test particles and light and discuss the corresponding orbits.

Saskia Grunau; Valeria Kagramanova; Jutta Kunz

2012-12-03T23:59:59.000Z

246

Buckling behaviour of ring-stiffned cylinders; experimental study  

Science Journals Connector (OSTI)

The effect of the number and size of rings on the buckling strength of ring-stiffened cylinders is studied experimentally. The results of ten machined ring-stiffened cylinders subjected to lateral pressure are presented. Five of the cylinders failed by the general instability mode and the rest failed by the shell instability mode. A sample of the experimental results which shows longitudinal and circumferential strains as well as the development of the circularity contours till collapse is presented. Buckling pressures obtained from the experiments are shown to be within 30% of the corresponding value obtained from the theoretical analysis available in the literature.

S.S. Seleim; J. Roorda

1986-01-01T23:59:59.000Z

247

Storage rings for investigation of ion-atom collisions  

SciTech Connect (OSTI)

In this survey, we give a brief description of synchrotron storage rings for heavy ions, and examples for their use in ion-atom collision physics. The compression of the phase space distribution of the ions by electron cooling, and the gain factors of in-ring experiments compared to single-pass experiments are explained. Some examples of a new generation of ion-atom collision experiments which may become feasible with storage rings are given. These include the studies of angular differential single- and double-electron capture cross sections, the production of slow highly charged recoil ions, and atomic collision processes using decelerated and crossed beam. 30 refs.

Schuch, R.

1987-08-01T23:59:59.000Z

248

Dynamic apeerture in damping rings with realistic wigglers  

SciTech Connect (OSTI)

The International Linear Collider based on superconducting RF cavities requires the damping rings to have extremely small equilibrium emittance, huge circumference, fast damping time, and large acceptance. To achieve all of these requirements is a very challenging task. In this paper, we will present a systematic approach to designing the damping rings using simple cells and non-interlaced sextupoles. The designs of the damping rings with various circumferences and shapes, including dogbone, are presented. To model realistic wigglers, we have developed a new hybrid symplectic integrator for faster and accurate evaluation of dynamic aperture of the lattices.

Cai, Yunhai; /SLAC

2005-05-04T23:59:59.000Z

249

Life Cycle Analysis: Integrated Gasification Combined Cycle (IGCC) Power Plant  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Life Cycle Analysis: Integrated Life Cycle Analysis: Integrated Gasification Combined Cycle (IGCC) Power Plant Revision 2, March 2012 DOE/NETL-2012/1551 Disclaimer This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference therein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or

250

Genetic analysis of synaptogyrin function in the synaptic vesicle cycle  

E-Print Network [OSTI]

Neuronal communication relies on the continual replenishment of synaptic vesicles that are primed for neurotransmitter release in response to action potentials. A vast array of proteins is required to mediate synaptic ...

Stevens, Robin J

2012-01-01T23:59:59.000Z

251

Frequency stabilization for a 486nm dye-ring laser  

E-Print Network [OSTI]

For my thesis, I worked towards using two reference cavities to provide frequency stabilization to a 486nm dye-ring laser. After a doubling cavity doubles the frequency to 243nm, the laser beam is used to excite ground ...

Sievers, Charles A. (Charles Anders), 1979-

2004-01-01T23:59:59.000Z

252

Use of gradient magnets in low emittance electron storage rings  

SciTech Connect (OSTI)

The use of gradient magnets for a low emittance electron storage ring is discussed and a magnetic lattice for a 6 GeV electron energy synchrotron radiation source adopting this feature is presented.

Vignola, G.

1985-01-01T23:59:59.000Z

253

Collective effects in a diffraction-limited storage ring  

Science Journals Connector (OSTI)

An overview of beam collective effects in diffraction-limited storage rings is given. The relation of a very low emittance machine and its stored beam to the former is described.

Nagaoka, R.

2014-08-27T23:59:59.000Z

254

Graphene Layer Growth Chemistry: Five-Six-Ring Flip Reaction  

E-Print Network [OSTI]

are incorporated into growing graphene layers and hence willGRAPHENE LAYER GROWTH CHEMISTRY: FIVE-SIX-RING FLIP REACTIONon the zigzag edge of a graphene layer. A new reaction

Whitesides, R.; Domin, D.; Salomon-Ferrer, R.; Lester Jr., W.A.; Frenklach, M.

2008-01-01T23:59:59.000Z

255

Ring Involutions and Self-Dual Codes Jay A. Wood  

E-Print Network [OSTI]

Ring Involutions and Self-Dual Codes Jay A. Wood Department of Mathematics Western Michigan University jay.wood@wmich.edu AMS meeting, Lexington, Kentucky March 27, 2010 #12;Acknowledgments Much

Wood, Jay

256

Characters and finite Frobenius rings Jay A. Wood  

E-Print Network [OSTI]

Characters and finite Frobenius rings Jay A. Wood Department of Mathematics Western Michigan-modules; 3. R = R as right R-modules. Due independently to Hirano, 1997, and Wood, 1999. JW (WMU) Frobenius

Wood, Jay

257

Landfill liner interface strengths from torsional-ring-shear tests  

SciTech Connect (OSTI)

A torsional-ring-shear apparatus and test procedure are described for measuring soil/geosynthetic and geosynthetic/geosynthetic interface strengths. Typical interface strengths are presented for a double-composite liner system and the relevancy of ring-shear strengths is illustrated using the slope failure at the Kettleman Hills Waste Repository, Kettleman City, Calif. The results of undrained ring-shear tests show that for a clay/geomembrane interface: (1) interface strength depends on plasticity and compaction water content of the clay, and the applied normal stress; (2) interface strengths measured with the torsional-ring-shear apparatus are in excellent agreement with back-calculated field strengths; and (3) peak and residual interface failure envelopes are nonlinear, and the nonlinearity should be modeled in stability analyses instead of as a combination of cohesion and friction angle. Design recommendations for interface strengths and stability analyses are also presented.

Stark, T.D. (Univ. of Illinois, Urbana, IL (United States)); Poeppel, A.R. (Langan Engineering Associates, Inc., New York, NY (United States))

1994-03-01T23:59:59.000Z

258

Photoswitchable Molecular Rings for Solar-Thermal Energy Storage  

Science Journals Connector (OSTI)

Photoswitchable Molecular Rings for Solar-Thermal Energy Storage ... Ground-state energy barriers along the NN torsional coordinates were also computed, along with excitation energies and intensities for the species that can contribute to the photostationary state. ...

E. Durgun; Jeffrey C. Grossman

2013-03-04T23:59:59.000Z

259

Fermilab Muon Ring Arrives to a Large Crowd of Fans  

SciTech Connect (OSTI)

A very large group of people gathered to watch the muon g-2 ring on its last leg of the big move from Brookhaven National Laboratory in Long Island, NY to Fermilab in Batavia, IL.

None

2013-08-15T23:59:59.000Z

260

Power Series Over Noetherian Rings February 4, 2013 William ...  

E-Print Network [OSTI]

Feb 4, 2013 ... ian rings and of the induced spectral maps associated with various ...... algebraic independence of ?1 over R, we have ht( ?P ?R1) = 1, and so...

2013-02-04T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

A Shallow Attenuating Anomaly Inside The Ring Fracture Of The...  

Open Energy Info (EERE)

Shallow Attenuating Anomaly Inside The Ring Fracture Of The Valles Caldera, New Mexico Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: A Shallow...

262

Coherence and destruction of coherence in mesoscopic rings  

Science Journals Connector (OSTI)

Recent investigations have shown that an important contribution to the magnetic response of an ensemble of mesoscopic normal metal rings at low temperatures is given by the coherent backscattering familiar fro...

Ulrich Eckern

1991-01-01T23:59:59.000Z

263

Injection and Extraction Lines for the ILC Damping Rings  

E-Print Network [OSTI]

INJECTION AND EXTRACTION LINES FOR THE ILC DAMPING RINGS ?the injection and extraction lines into and out of the ILCas the design for the abort line. Due to changes of the geo-

Reichel, Ina

2008-01-01T23:59:59.000Z

264

TIGHT CLOSURE IN GRADED RINGS Karen E. Smith \\Lambda  

E-Print Network [OSTI]

TIGHT CLOSURE IN GRADED RINGS Karen E. Smith \\Lambda Abstract. This paper facilitates is supported by the U.S. National Science Foundation. Typeset by A M S­T E X 1 #12; 2 KAREN E. SMITH \\Lambda

Smith, Karen E.

265

Suppression of ring artefacts when tomographing anisotropically attenuating samples  

Science Journals Connector (OSTI)

An intensity normalization technique is proposed to suppress ring artefacts of varying strength. The method was applied to an elongated sample in a monochromatic beam and to a sample with highly attenuated parts in a white beam.

Titarenko, S.

2011-04-02T23:59:59.000Z

266

Triangularly phase-modulated optical fiber ring resonator sensor  

Science Journals Connector (OSTI)

An optical fiber ring resonatory sensor system has been demonstrated by applying a triangular phase modulation signal to a fiber loop. The dynamic range for detection of optical phase...

Chien, Pie-Yau; Pan, Ci-Ling

1992-01-01T23:59:59.000Z

267

Instability issues for the ESS linac and rings  

SciTech Connect (OSTI)

Comments are made on beam instability issues in the ESS linac and rings. The topics of interest in the linac are halo generation in the absence and presence of machine imperfections, and also the stability of the momentum ramping of the output beam. In the case of the rings, the main concern is for fast coherent transverse instabilities due to the combined effect of coupled electron-proton oscillations and interaction with the wall impedances.

Rees, G. H. [Rutherford Appleton Laboratory, CLRC (United Kingdom)

1999-12-03T23:59:59.000Z

268

Laser plasma focus produced in a ring target  

Science Journals Connector (OSTI)

A new geometry for generating a laser?produced plasma is presented. A toroidalmirror is used to focus a CO2laser beam on the inside wall of a copper ring target. The plasma produced converges at the center of the ring where an axial plasma focus is formed. High?speed photography shows details of a plasma generated at a distance from the target surface. This new geometry could have important applications in the field of x?ray lasers.

G. Saint?Hilaire; Z. Szili

1976-01-01T23:59:59.000Z

269

Neural modeling of vapor compression refrigeration cycle with extreme learning machine  

Science Journals Connector (OSTI)

In this paper, a single-hidden layer feed-forward neural network (SLFN) is used to model the dynamics of the vapor compression cycle in refrigeration and air-conditioning systems, based on the extreme learning machine (ELM). It is shown that the assignment ... Keywords: Back propagation, Extreme learning machine, Modeling, Radial basis function, Support vector regression, Vapor compression refrigeration cycle

Lei Zhao; Wen-Jian Cai; Zhi-Hong Man

2014-03-01T23:59:59.000Z

270

Role of SRP RNA in the GTPase Cycles of Ffh and FtsY  

Science Journals Connector (OSTI)

Role of SRP RNA in the GTPase Cycles of Ffh and FtsY ... The bacterial homologues of the signal recognition particle (SRP) and its receptor, the Ffh4.5S ... These results suggest that 4.5S RNA modulates the conformation of the FfhFtsY complex and may, in turn, regulate its GTPase activity during the SRP functional cycle. ...

Paul Peluso; Shu-ou Shan; Silke Nock; Daniel Herschlag; Peter Walter

2001-11-20T23:59:59.000Z

271

The behavioral manipulation hypothesis Life cycle of  

E-Print Network [OSTI]

1 The behavioral manipulation hypothesis · No one knows how the parasite causes these Life cycle eat mostly hares · Linked cycles? Predator-Prey Cycles? · Think and then discuss: · Under the hypothesis that predators cause this cycle, what would you expect for the following when hare populations

Mitchell, Randall J.

272

Flamevortex interaction in a reacting vortex ring  

Science Journals Connector (OSTI)

Direct numerical simulations are used to study the flamevortex interaction in a laminar reacting vortex ring. The chemical reaction occurs by a one-step Arrhenius-type reaction that mimics the combustion of typical hydrocarbon and air. The ring is generated by an axisymmetric jet that is impulsed to emit a cold fuel through a nozzle. The fuel enters a quiescent ambient at a much higher temperature. By adjusting the ratio of the ambient and fuel temperatures the ignition either occurs during the formation or post-formation phase of the ring. When ignition occurs during the formation phase of the ring the bulk of combustion is by a flame at the front of the vortex bubble. When ignition is delayed until after the formation phase most of the reaction occurs inside the vortex ring. It is found that premixing the fuel and the oxidizer enhances the amount of product formation. The heat released from the reaction significantly affects production redistribution and diffusion of the vorticity throughout the field. The results of the simulations also reveal that the heat of reaction affects the strain rate fields differently depending on when the ignition of the ring occurs.

J. S. Hewett; C. K. Madnia

1998-01-01T23:59:59.000Z

273

SNMR pulse sequence phase cycling  

DOE Patents [OSTI]

Technologies applicable to SNMR pulse sequence phase cycling are disclosed, including SNMR acquisition apparatus and methods, SNMR processing apparatus and methods, and combinations thereof. SNMR acquisition may include transmitting two or more SNMR pulse sequences and applying a phase shift to a pulse in at least one of the pulse sequences, according to any of a variety cycling techniques. SNMR processing may include combining SNMR from a plurality of pulse sequences comprising pulses of different phases, so that desired signals are preserved and indesired signals are canceled.

Walsh, David O; Grunewald, Elliot D

2013-11-12T23:59:59.000Z

274

Simple ocean carbon cycle models  

SciTech Connect (OSTI)

Simple ocean carbon cycle models can be used to calculate the rate at which the oceans are likely to absorb CO{sub 2} from the atmosphere. For problems involving steady-state ocean circulation, well calibrated ocean models produce results that are very similar to results obtained using general circulation models. Hence, simple ocean carbon cycle models may be appropriate for use in studies in which the time or expense of running large scale general circulation models would be prohibitive. Simple ocean models have the advantage of being based on a small number of explicit assumptions. The simplicity of these ocean models facilitates the understanding of model results.

Caldeira, K. [Lawrence Livermore National Lab., CA (United States); Hoffert, M.I. [New York Univ., NY (United States). Dept. of Earth System Sciences; Siegenthaler, U. [Bern Univ. (Switzerland). Inst. fuer Physik

1994-02-01T23:59:59.000Z

275

Closed cycle liquid helium refrigerators  

Science Journals Connector (OSTI)

We have developed closed cycle liquid helium refrigerators using a Joule Thomson circuit precooled by commercially available two staged Gifford Mac Mahon cryocoolers. The Joule Thomson counterflow heat exchangers are modular and have been thermo-hydraulically characterized. Fully automatic cool down and operation are achieved by two pneumatically driven by pass and expansion valves. Several apparatus have been built or are under assembly with cooling power ranging from 100 mW up to 5 Watt, for temperature ranging from 2.8 K up to 4.5 K. A trouble free operation with several warm up and cool down cycles has been proven over 7000 hours.

G. Claudet; R. Lagnier; A. Ravex

1992-01-01T23:59:59.000Z

276

Life Cycle Assessment for Sustainable Metropolitan Water Systems Planning  

Science Journals Connector (OSTI)

Life Cycle Assessment (LCA) is useful as an information tool for the examination of alternative future scenarios for strategic planning. ... Water systems supply additional functions includ ing the following:? (1) nutrient recovery ? the treatment and land application of biosolids brings back the nutrients to the natural cycle in agriculture, horticulture, and forest systems, which can prevent the need for chemical fertilizers and thus avoid their production; (2) energy recovery ? which can include the generation of electricity or the cogeneration of thermal energy and electricity from biogas at sewage treat ment plants (STPs) or biosolids combustion off-site [This generation activity replaces the production of electrical and thermal energy from other energy sources.]; ...

Sven Lundie; Gregory M. Peters; Paul C. Beavis

2004-05-21T23:59:59.000Z

277

Can the ring polymer molecular dynamics method be interpreted as real time quantum dynamics?  

SciTech Connect (OSTI)

The ring polymer molecular dynamics (RPMD) method has gained popularity in recent years as a simple approximation for calculating real time quantum correlation functions in condensed media. However, the extent to which RPMD captures real dynamical quantum effects and why it fails under certain situations have not been clearly understood. Addressing this issue has been difficult in the absence of a genuine justification for the RPMD algorithm starting from the quantum Liouville equation. To this end, a new and exact path integral formalism for the calculation of real time quantum correlation functions is presented in this work, which can serve as a rigorous foundation for the analysis of the RPMD method as well as providing an alternative derivation of the well established centroid molecular dynamics method. The new formalism utilizes the cyclic symmetry of the imaginary time path integral in the most general sense and enables the expression of Kubo-transformed quantum time correlation functions as that of physical observables pre-averaged over the imaginary time path. Upon filtering with a centroid constraint function, the formulation results in the centroid dynamics formalism. Upon filtering with the position representation of the imaginary time path integral, we obtain an exact quantum dynamics formalism involving the same variables as the RPMD method. The analysis of the RPMD approximation based on this approach clarifies that an explicit quantum dynamical justification does not exist for the use of the ring polymer harmonic potential term (imaginary time kinetic energy) as implemented in the RPMD method. It is analyzed why this can cause substantial errors in nonlinear correlation functions of harmonic oscillators. Such errors can be significant for general correlation functions of anharmonic systems. We also demonstrate that the short time accuracy of the exact path integral limit of RPMD is of lower order than those for finite discretization of path. The present quantum dynamics formulation also serves as the basis for developing new quantum dynamical methods that utilize the cyclic nature of the imaginary time path integral.

Jang, Seogjoo, E-mail: sjang@qc.cuny.edu [Department of Chemistry and Biochemistry, Queens College and the Graduate Center, City University of New York, 65-30 Kissena Boulevard, Flushing, New York 11367 (United States)] [Department of Chemistry and Biochemistry, Queens College and the Graduate Center, City University of New York, 65-30 Kissena Boulevard, Flushing, New York 11367 (United States); Sinitskiy, Anton V.; Voth, Gregory A., E-mail: gavoth@uchicago.edu [Department of Chemistry, James Franck Institute, Institute for Biophysical Dynamics and Computation Institute, University of Chicago, 5735 S. Ellis Avenue, Chicago, Illinois 60637 (United States)

2014-04-21T23:59:59.000Z

278

Spy1 regulation of the cell cycle, checkpoint activation and apoptosis  

E-Print Network [OSTI]

Silva LF, Duncker BP. ORC function in late G1: maintaining128-30. DePamphilis ML. The 'ORC cycle': a novel pathway forOrigin Recognition Complex (ORC), cdc6/18, cdc45, cdt1, the

Gastwirt, Randy Francis

2008-01-01T23:59:59.000Z

279

E-Print Network 3.0 - apophyseal ring fracture Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

fracture Search Powered by Explorit Topic List Advanced Search Sample search results for: apophyseal ring fracture...

280

GAX absorption cycle design process  

SciTech Connect (OSTI)

This paper presents an absorption system design process that relies on computer simulations that are validated by experimental findings. An ammonia-water absorption heat pump cycle at 3 refrigeration tons (RT) and chillers at 3.3 RT and 5 RT (10.5 kW, 11.6 kW, and 17.6 kW) were initially modeled and then built and tested. The experimental results were used to calibrate both the cycle simulation and the component simulations, yielding computer design routines that could accurately predict component and cycle performance. Each system was a generator-absorber heat exchange (GAX) cycle, and all were sized for residential and light commercial use, where very little absorption equipment is currently used. The specific findings of the 5 RT (17.6 kW) chiller are presented. Modeling incorporated a heat loss from the gas-fired generator and pressure drops in both the evaporator and absorber. Simulation results and experimental findings agreed closely and validated the modeling method and simulation software.

Priedeman, D.K.; Christensen, R.N.

1999-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

The Distribution of Dark Matter in a Ringed Galaxy  

E-Print Network [OSTI]

Outer rings are located at the greatest distance from the galaxy center of any feature resonant with a bar. Because of their large scale, their morphology is sensitive to the distribution of the dark matter in the galaxy. We introduce here how study of these rings can constrain the mass-to-light ratio of the bar, and so the percentage of dark matter in the center of these galaxies. We compare periodic orbits integrated in the ringed galaxy NGC 6782 near the outer Lindblad resonance to the shape of the outer ring. The non-axisymmetric component of the potential resulting from the bar is derived from a near-infrared image of the galaxy. The axisymmetric component is derived assuming a flat rotation curve. We find that the pinched non-self-intersecting periodic orbits are more elongated for higher bar mass-to-light ratios and faster bars. The inferred mass-to-light ratio of the bar depends on the assumed inclination of the galaxy. With an assumed galaxy inclination of i=41 degrees, for the orbits to be consistent with the observed ring morphology the mass-to-light ratio of the bar must be high, greater than 70% of a maximal disk value. For i=45 degrees, the mass-to-light ratio of the bar is $75\\pm 15%$ of the maximal disk value. Since the velocity field of these rings can be used to constrain the galaxy inclination as well as which periodic orbit is represented in the ring, further study will yield tighter constraints on the mass-to-light ratio of the bar. If a near maximal disk value for the bar is required, then either there would be little dark matter within the bar, or the dark matter contained in the disk of the galaxy would be non-axisymmetric and would rotate with the bar.

A. C. Quillen; J. A. Frogel

1996-09-05T23:59:59.000Z

282

Rankine and Brayton Cycle Cogeneration for Glass Melting  

E-Print Network [OSTI]

Rankine cycle, b) an organic Rankine cycle, c) an indirectly heated positive pressure Brayton cycle and d) a directly heated subatmospheric Brayton cycle. For the specified flue gas temperatures considered, the organic Rankine cycle produced the most...

Hnat, J. G.; Patten, J. S.; Sheth, P. R.

1981-01-01T23:59:59.000Z

283

Definition: Rankine cycle | Open Energy Information  

Open Energy Info (EERE)

Rankine cycle Rankine cycle Jump to: navigation, search Dictionary.png Rankine cycle Sometimes referred to as the steam cycle. Fuel is used to heat a liquid to produce a high pressure gas that expands and produces work, such as turning a turbine; when the turbine is connected to a generator, it produces electricity. Usually water is the liquid used in the Rankine cycle (to produce steam), but other liquids can also be used. The exhaust vapor expelled from the turbine condenses and the liquid is pumped back to the boiler to repeat the cycle.[1][2] View on Wikipedia Wikipedia Definition The Rankine cycle is a mathematical model that is used to predict the performance of steam engines. The Rankine cycle is an idealised thermodynamic cycle of a heat engine that converts heat into mechanical

284

Kalina combined cycle performance and operability  

SciTech Connect (OSTI)

Gas turbine combined cycles using Rankine bottoming cycles have gained broad market acceptance. The favorable plant economics derive from their high efficiency, short construction cycles and excellent environmental performance. The responsive operating characteristics of combined cycles is another key advantage for customers. Duty cycles cover the spectrum from daily start stop (DSS) to base load. Performance and economics of combined cycles have progressed with advances in gas turbine technology as well as the introduction of increasingly efficient multi-pressure Rankine bottoming cycles. Further advances in gas turbine technology and Rankine bottoming cycle performance are becoming incrementally more difficult and costly to achieve. The availability of the Kalina cycle presents a clear path toward improved combined-cycle system performance and reduced cost of electricity. This paper presents detailed performance and operating characteristics of a STAG 207FA combined cycle employing the Kalina bottoming cycle. These characteristics are compared to a conventional three-pressure reheat Rankine bottoming cycle. The Kalina cycle is shown to have performance and operability advantages throughout the range of site conditions and operating regimes, such as base load, load following, DSS duty, wet and dry cooling tower applications and unattended operation. These advantages derive from a single-pressure once-through heat recovery system, above atmospheric working fluid pressure throughout the system, above atmospheric working fluid pressure throughout the system, very high thermal efficiency ({approximately}2.0 to 2.5 percentage points better than the best Rankine), and compatibility with sub-freezing ambient conditions.

Smith, R.W.; Ranasinghe, J.; Stats, D.; Dykas, S.

1996-12-31T23:59:59.000Z

285

Rankine cycle leak detection via continuous monitoring  

SciTech Connect (OSTI)

Rankine cycle power plants operate on a closed cycle in which heat is transferred from a high temperature reservoir to a low temperature sink while performing useful work. leaks in this cycle cause the loss of working fluid and/or corrosion of the power plant. Both of these constitute a loss of capital assets. A severe leak can reduce the efficiency of the cycle to the extent of creating an operating loss. PNL is undertaking the development of continuous monitoring techniques to protect rankine cycle plants from such losses. The location of these continuous monitors on an organic rankine cycle is described and shown schematically.

Kindle, Cecil H.

1982-10-08T23:59:59.000Z

286

Milnor K-theory and the graded representation ring  

E-Print Network [OSTI]

Let F be a field, let G be its absolute Galois group, and let R(G, k) be the representation ring of G over a suitable field k. In this preprint we construct a ring homomorphism from the mod 2 Milnor K-theory k_*(F) to the graded ring gr R(G, k) associated to Grothendieck's \\gamma-filtration. We study this map in particular cases, as well as a related map involving the W-group of F rather than G. The latter is an isomorphism in all cases considered. Naturally this echoes the Milnor conjecture (now a theorem), which states that k_*(F) is isomorphic to the mod 2 cohomology of the absolute Galois group G, and to the graded Witt ring gr W(F). The machinery developed to obtain the above results seems to have independent interest in algebraic topology. We are led to construct an analog of the classical Chern character, which does not involve complex vector bundles and Chern classes but rather real vector bundles and Stiefel-Whitney classes. Thus we show the existence of a ring homomorphism whose source is the graded...

Guillot, Pierre

2011-01-01T23:59:59.000Z

287

Deciphering Climate from the Characterization of Ring Width, Carbon, and Oxygen Isotopes in Latewood Tree-Ring Cellulose, Big Thicket National Preserve, Texas, USA  

E-Print Network [OSTI]

for their help with the project. Dr. Mora gave me the opportunity to pursue a Ph.D. in tree-ring chemistry. Dr in Latewood Tree-Ring Cellulose, Big Thicket National Preserve, Texas, USA A Dissertation Presented. Grissino-Mayer mentored me as a new dendrochronologist, and is ultimately the reason I chose tree rings

Grissino-Mayer, Henri D.

288

Where and when does a ring start and end? Testing the ring-species hypothesis in a species complex of Australian parrots  

Science Journals Connector (OSTI)

...s00122-006-0381-4 Higgins, P.J Handbook of Australian, New Zealand and Antarctic...dots) all as in figure 3 Where and when does a ring start and end? Testing the ring-species...to form. A ring speciation hypothesis does not explain the patterns we have observed...

2008-01-01T23:59:59.000Z

289

NREL: U.S. Life Cycle Inventory Database - Life Cycle Assessments  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Life Cycle Assessments A life cycle assessment (LCA) is a systematic, cradle-to-grave process that evaluates the environmental impacts of products, processes, and services. Its...

290

Medium Truck Duty Cycle (MTDC)  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Routes Data Acquisition System Setup Routes Data Acquisition System Setup Medium Truck Duty Cycle (MTDC) Objective This Department of Energy project focuses on the collection and analysis medium truck (Class-6 and -7) duty cycle data from real-world operations. Analysis of this data will provide information pertaining to the fuel efficiencies and performance of medium trucks in several vocations. Outcomes Rich source of data and information that can contribute to the development of new tools Sound basis upon which DOE can make technology investment decisions A national archive of real-world-based medium-truck operational data that will support medium-duty vehicle energy efficiency research Collected Data Speed & Acceleration Fuel Consumption GPS Location Road Grade

291

The Life Cycle Analysis Toolbox  

SciTech Connect (OSTI)

The life cycle analysis toolbox is a valuable integration of decision-making tools and supporting materials developed by Oak Ridge National Laboratory (ORNL) to help Department of Energy managers improve environmental quality, reduce costs, and minimize risk. The toolbox provides decision-makers access to a wide variety of proven tools for pollution prevention (P2) and waste minimization (WMin), as well as ORNL expertise to select from this toolbox exactly the right tool to solve any given P2/WMin problem. The central element of the toolbox is a multiple criteria approach to life cycle analysis developed specifically to aid P2/WMin decision-making. ORNL has developed numerous tools that support this life cycle analysis approach. Tools are available to help model P2/WMin processes, estimate human health risks, estimate costs, and represent and manipulate uncertainties. Tools are available to help document P2/WMin decision-making and implement programs. Tools are also available to help track potential future environmental regulations that could impact P2/WMin programs and current regulations that must be followed. An Internet-site will provide broad access to the tools.

Bishop, L.; Tonn, B.E.; Williams, K.A.; Yerace, P.; Yuracko, K.L.

1999-02-28T23:59:59.000Z

292

Magnetic edge states in Aharonov-Bohm graphene quantum rings  

SciTech Connect (OSTI)

The effect of electron-electron interaction on the electronic structure of Aharonov-Bohm (AB) graphene quantum rings (GQRs) is explored theoretically using the single-band tight-binding Hamiltonian and the mean-field Hubbard model. The electronic states and magnetic properties of hexagonal, triangular, and circular GQRs with different sizes and zigzag edge terminations are studied. The results show that, although the AB oscillations in the all types of nanoring are affected by the interaction, the spin splitting in the AB oscillations strongly depends on the geometry and the size of graphene nanorings. We found that the total spin of hexagonal and circular rings is zero and therefore, no spin splitting can be observed in the AB oscillations. However, the non-zero magnetization of the triangular rings breaks the degeneracy between spin-up and spin-down electrons, which produces spin-polarized AB oscillations.

Farghadan, R., E-mail: rfarghadan@kashanu.ac.ir; Heidari Semiromi, E. [Department of Physics, University of Kashan, Kashan (Iran, Islamic Republic of); Saffarzadeh, A. [Department of Physics, Payame Noor University, P.O. Box 19395-3697 Tehran (Iran, Islamic Republic of); Department of Physics, Simon Fraser University, Burnaby, British Columbia V5A 1S6 (Canada)

2013-12-07T23:59:59.000Z

293

Electron Cloud Mitigation in the Spallation Neutron Source Ring  

SciTech Connect (OSTI)

The Spallation Neutron Source (SNS) accumulator ring is designed to accumulate, via H{sup -} injection, protons of 2 MW beam power at 1 GeV kinetic energy at a repetition rate of 60 Hz [1]. At such beam intensity, electron-cloud is expected to be one of the intensity-limiting mechanisms that complicate ring operations. This paper summarizes mitigation strategy adopted in the design, both in suppressing electron-cloud formation and in enhancing Landau damping, including tapered magnetic field and monitoring system for the collection of stripped electrons at injection, TiN coated beam chamber for suppression of the secondary yield, clearing electrodes dedicated for the injection region and parasitic on BPMs around the ring, solenoid windings in the collimation region, and planning of vacuum systems for beam scrubbing upon operation.

Wei, J.; Blaskiewicz, Michael; Brodowski, J.; Cameron, P.; Davino, Daniele; Fedotov, A.; He, P.; Hseuh, H.; Lee, Y.Y.; Ludewig, H.; Meng, W.; Raparia, D.; Tuozzolo, J.; Zhang, S.Y.; Catalan-Lasheras, N.; Macek, R.J.; Furman, Miguel A.; Aleksandrov, A.; Cousineau, S.; Danilov, V.; Henderson, S.; /Brookhaven /CERN /LANL, Ctr. for Nonlinear Studies /LBL, Berkeley /Oak Ridge /SLAC

2008-03-17T23:59:59.000Z

294

Mechanical seal having a single-piece, perforated mating ring  

DOE Patents [OSTI]

A mechanical seal (e.g., single mechanical seals, double mechanical seals, tandem mechanical seals, bellows, pusher mechanical seals, and all types of rotating and reciprocating machines) with reduced contact surface temperature, reduced contact surface wear, or increased life span. The mechanical seal comprises a rotating ring and a single-piece, perforated mating ring, which improves heat transfer by controllably channeling coolant flow through the single-piece mating ring such that the coolant is in substantially uniform thermal contact with a substantial portion of the interior surface area of the seal face, while maintaining the structural integrity of the mechanical seal and minimizing the potential for coolant flow interruptions to the seal face caused by debris or contaminants (e.g., small solids and trash) in the coolant.

Khonsari, Michael M. (Baton Rouge, LA); Somanchi, Anoop K. (Fremont, CA)

2007-08-07T23:59:59.000Z

295

The Quebec Life Cycle Inventory Database Project  

Science Journals Connector (OSTI)

Life cycle assessment (LCA) in Quebec (Canada) is increasingly important. Yet, ... life cycle inventory (LCI) data. The Quebec government invested in the creation of a Quebec LCI database. The approach is to work...

Pascal Lesage; Rjean Samson

2013-05-01T23:59:59.000Z

296

Profit cycle dynamics by Kawika Pierson.  

E-Print Network [OSTI]

My thesis consists of three essays investigating the existence, causes, and mitigation of profit cycles at an industry level. The first essay examines profit cycles by proposing that the industry-specific features of how ...

Pierson, Kawika (Kawika Paul)

2011-01-01T23:59:59.000Z

297

Rethinking the light water reactor fuel cycle  

E-Print Network [OSTI]

The once through nuclear fuel cycle adopted by the majority of countries with operating commercial power reactors imposes a number of concerns. The radioactive waste created in the once through nuclear fuel cycle has to ...

Shwageraus, Evgeni, 1973-

2004-01-01T23:59:59.000Z

298

Viable combined cycle design for automotive applications  

Science Journals Connector (OSTI)

A relatively new approach for improving fuel economy and automotive engine performance involves the use of automotive combined cycle generation technologies. The combined cycle generation, a process widely used i...

K. -B. Kim; K. -W. Choi; K. -H. Lee

2012-04-01T23:59:59.000Z

299

Coal-Fuelled Combined Cycle Power Plants  

Science Journals Connector (OSTI)

Combined cycle power plant, when used as a generic ... which converts heat into mechanical energy in a combined gas and steam turbine process. Combined cycle processes with coal gasification or coal combustion .....

Dr. Hartmut Spliethoff

2010-01-01T23:59:59.000Z

300

Toward single-cycle optical pulses  

E-Print Network [OSTI]

Single-cycle optical pulses, the never-before-achieved regime, have a great potential for attosecond science and phase-sensitive nonlinear optics. To achieve single-cycle optical pulses by active synchronization, three ...

Kim, Jung-Won, 1976-

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Progress and commissioning of the SLD Cherenkov Ring Imaging Detector. Revision  

SciTech Connect (OSTI)

We report the recent progress of the SLD Cherenkov Ring Imaging Detector. All of the individual components of the device (TPC`s, mirrors, liquid radiator trays) have been completed and installed. Almost half of the electronics packages are installed and operational, and the data acquisition system has been commissioned. The liquid C{sub 6}F{sub 14} recirculation system is functioning. The drift gas supply systems are operating well with TMAE, and the gaseous Freon C{sub 5}F{sub 12} recirculator is being brought on-line. Our monitor and control systems are fully functional. The commissioning of all 40 TPCs at full operating voltage has gone very smoothly. The system shows a remarkable immunity to the SLC backgrounds, and yields very clean events, while operating with a single electron sensitivity.

Abe, K.; Hasegawa, K.; Suekane, F.; Yuta, H. [Tohoku Univ., Sendai (Japan). Dept. of Physics; Antilogus, P.; Aston, D.; Bienz, T.; Bird, F.; Dasu, S.; Dolinsky, S.; Dunwoodie, W.; Hallewell, G.: Kawahara, H.; Kwon, Y.; Leith, D.W.G.S.; Muller, D.; Nagamine, T.; Pavel, T.J.; Ratcliff, B.; Rensing, P.; Schultz, D.; Shapiro, S.; Simopoulos, C.; Solodov, E.; Toge, N.; Va`vra, J.; Williams, S.H. [Stanford Linear Accelerator Center, Menlo Park, CA (United States); Baird, K.; Jacques, P.; Kalelkar, M.; Plano, R.; Stamer, P.; Word, G. [Rutgers--the State Univ., Piscataway, NJ (United States). Serin Physics Lab.; Bean, A.; Caldwell, D.; Duboscq, J.; Huber, J.; Lu, A.; Mathys, L.; McHugh, S.; Witherell, M.; Yellin, S. [California Univ., Santa Barbara, CA (United States). Dept. of Physics; Cavalli-Sforza, M.; Coyle, P.; Coyne, D.; Gagnon, P.; Liu, X.; Williams, D.A. [California Univ., Santa Cruz, CA (United States). Inst. for Particle Physics; d`Oliveira, A.; Johnson, R.A.; Martinez, J.; Meadows, B.; Nussbaum, M.; Santha, A.K.S.; Shoup, A.; Sokoloff, M.; Stockdale, I. [Cincinnati Univ., OH (United States). Dept. of Physics; Whitaker, J.S.; Wilson, R.J. [Boston Univ., MA (United States). Dept. of Physics

1991-11-01T23:59:59.000Z

302

On near-rings associated with generalized affine planes  

E-Print Network [OSTI]

ON NEAR-RINGS ASSOCIATED WITH GENERALIZED AFFINE PLANES A Thesis by NANCY JANE ARMENTROUT Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE August 1971... Ma)or Subject: Mathematics ON NEAR-RINGS ASSOCIATED WITH GENERALIZED AI'FINE PLANES A Thesis NANCY JANE ARMENTROUT Approved as to style and content by: A, n. ;s-, . (Chairma of Committee) c ~ g~~+ (Head of Department) (Member) (Member) Mem...

Armentrout, Nancy Jane

1971-01-01T23:59:59.000Z

303

Superconducting travelling wave ring with high gradient accelerating section  

SciTech Connect (OSTI)

Use of a superconducting traveling wave accelerating (STWA) structure instead of a standing wave cavity has major advantages in increasing the accelerating gradient in the ILC. In contrast with standing wave cavity STWA requires feedback loop, which sends wave from the structure output to input, making a superconducting traveling wave ring (STWR). One or few input couplers need to excite STWR and compensate power dissipations due to beam loading. To control traveling wave regime in the structure two independent knobs can be used for tuning both resonant ring frequency and backward wave. We discuss two variants of the STWR with one and two feed couplers.

Avrakhov, P.; Solyak, N.; /Fermilab

2007-06-01T23:59:59.000Z

304

Development Plan for the Fuel Cycle Simulator  

SciTech Connect (OSTI)

The Fuel Cycle Simulator (FCS) project was initiated late in FY-10 as the activity to develop a next generation fuel cycle dynamic analysis tool for achieving the Systems Analysis Campaign 'Grand Challenge.' This challenge, as documented in the Campaign Implementation Plan, is to: 'Develop a fuel cycle simulator as part of a suite of tools to support decision-making, communication, and education, that synthesizes and visually explains the multiple attributes of potential fuel cycles.'

Brent Dixon

2011-09-01T23:59:59.000Z

305

Using Cycles and Scaling Parallel Algorithms  

E-Print Network [OSTI]

graph by finding a max­ imal set of edge­disjoint cycles. We give a parallel algorithm to find the first efficient parallel algorithm for finding an approximation to a min­ imum cycle cover. Our algorithm finds a cycle cover whose size is within a factor of O(1 + n log n m+n ) of the minimum sized

Yang, Junfeng

306

How Minds Work The IDA Cognitive Cycle  

E-Print Network [OSTI]

1 How Minds Work The IDA Cognitive Cycle Stan Franklin Computer Science Division & Institute for Intelligent Systems The University of Memphis #12;HMW: The IDA Cognitive Cycle 2 Memory Systems #12;HMW: The IDA Cognitive Cycle 3 Global Workspace Theory I · The nervous system is a distributed parallel

Memphis, University of

307

SPACETELESCOPESCIENCEINSTITUTE WFPC2 Cycle 14 Calibration  

E-Print Network [OSTI]

/chip combinations used for science in Cycle 14 + Close Out ~10% reserve 2 Placeholder for unexpected items. TOTALSPACETELESCOPESCIENCEINSTITUTE WFPC2 Cycle 14 Calibration Director's Review 8 August 2005 John Biretta 1 Cycle 14 WFPC2 Calibration Plan Overall Goals: · Monitor & maintain WFPC2 health & safety

Sirianni, Marco

308

Grand Challenges for Life-Cycle Assessment of Biofuels  

Science Journals Connector (OSTI)

Grand Challenges for Life-Cycle Assessment of Biofuels ... Both advocates and critics of biofuels often focus on a restricted set of scenarios that appear to reinforce their a priori beliefs about how biofuel production and use might function. ... Converting rain forest, peatland, savanna, or grassland to produce food crop-based biofuels in Brazil, southeast Asia, and the US creates a biofuel C debt by releasing 17-420 times more CO2 than the annual greenhouse gas (GHG) redns. ...

T. E. McKone; W. W. Nazaroff; P. Berck; M. Auffhammer; T. Lipman; M. S. Torn; E. Masanet; A. Lobscheid; N. Santero; U. Mishra; A. Barrett; M. Bomberg; K. Fingerman; C. Scown; B. Strogen; A. Horvath

2011-01-25T23:59:59.000Z

309

A CAVITY RING-DOWN SPECTROSCOPY MERCURY CONTINUOUS EMISSION MONITOR  

SciTech Connect (OSTI)

The construction of the sampling system was completed during the past quarter. The sampling system has been built on a 3 feet x 4 feet x 2 inch breadboard table. The laser system, all the associated optics, and the mounts and hardware needed to couple the UV light into the fiber optic have also been condensed and placed on an identical 3 feet x 4 feet x 2 inch breadboard table. This reduces the footprint of each system for ease of operation at a field test facility. The two systems are only connected with a fiber optic, to bring the UV light to the CRD cavity, and a single coaxial cable used to apply a voltage to the diode seed laser to scan the frequency over the desired mercury transition. SRD software engineers applied a couple of software fixes to correct the problems of the diode seed laser drifting or mode hopping. Upon successful completion of the software fixes another long-term test was conducted. A nearly 3 day long, 24 hours/day, test was run to test out the new subroutines. Everything appeared to work as it should and the mercury concentrations were accurately reported for the entire test, with the exception of a small interval of time when the intensity of the UV light dropped low enough that the program was no longer triggering properly. After adjusting the power of the laser the program returned to proper operation. With the successful completion of a relatively long test SRD software engineer incorporated the new subroutine into an entirely new program. This program operates the CRD instrument automatically as a continuous emissions monitor for mercury. In addition the program also reports the concentration of SO{sub 2} determined in the sample flue gas stream. Various functions, operation of, and a description of the new program have been included with this report. This report concludes the technical work associated with Phase II of the Cavity Ring-Down project for the continuous detection of trace levels of mercury. The project is presently gearing up for additional testing in preparation for a field test to be conducted at the DOE/NETL pilot plant facility in Pittsburgh, Pennsylvania.

Christopher C. Carter

2004-03-31T23:59:59.000Z

310

Status of Studies of Achromat-based 6D Ionization Cooling Rings for Muons  

SciTech Connect (OSTI)

Six dimensional ionization cooling of muons is needed to achieve the necessary luminosity for a muon collider. If that cooling could occur over multiple turns in a closed ring, there would be significant cost savings over a single-pass cooling channel. We report on the status of a cooling ring with achromatic arcs. The achromatic design permits the design to easily switch between a closed ring and a snaking geometry on injection or extraction from the ring. The ring is designed with sufficient space in each superperiod for injection and extraction magnets. We describe the ring's lattice design, performance, and injection/extraction requirements.

Ding, X.; Kirk, H.; Cline, D.; Garren, A.A.; Berg, J.S.

2011-09-04T23:59:59.000Z

311

Building Life Cycle Cost Programs | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Building Life Cycle Cost Programs Building Life Cycle Cost Programs The National Institute of Standards and Technology (NIST) developed the Building Life Cycle Cost (BLCC) Program...

312

Life Cycle Assessment Comparing the Use of Jatropha Biodiesel...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

on Climate Change IR Indian Railways Jatropha Jatropha curcas L. KCl potassium chloride LCA life cycle assessment LCI life cycle inventory LCIA life cycle impact assessment MSRTH...

313

Working fluid design for organic rankine cycle systems (ORC):.  

E-Print Network [OSTI]

??The Organic Rankine Cycle is an energy conversion cycle similar to the conventional Rankine cycle which runs on a working fluid other than water. The (more)

Hattiangadi, A.

2013-01-01T23:59:59.000Z

314

Working Fluid Design for Organic Rankine Cycle (ORC) Systems:.  

E-Print Network [OSTI]

??The Organic Rankine Cycle is an energy conversion cycle similar to the conventional Rankine cycle which runs on a working fluid other than water. The (more)

Hattiangadi, A.

2013-01-01T23:59:59.000Z

315

Advanced Fuel Cycle Economic Sensitivity Analysis  

SciTech Connect (OSTI)

A fuel cycle economic analysis was performed on four fuel cycles to provide a baseline for initial cost comparison using the Gen IV Economic Modeling Work Group G4 ECON spreadsheet model, Decision Programming Language software, the 2006 Advanced Fuel Cycle Cost Basis report, industry cost data, international papers, the nuclear power related cost study from MIT, Harvard, and the University of Chicago. The analysis developed and compared the fuel cycle cost component of the total cost of energy for a wide range of fuel cycles including: once through, thermal with fast recycle, continuous fast recycle, and thermal recycle.

David Shropshire; Kent Williams; J.D. Smith; Brent Boore

2006-12-01T23:59:59.000Z

316

MHD Integrated Topping Cycle Project  

SciTech Connect (OSTI)

This eighteenth quarterly technical progress report of the MHD Integrated Topping cycle Project presents the accomplishments during the period November 1, 1991 to January 31, 1992. The precombustor is fully assembled. Manufacturing of all slagging stage components has been completed. All cooling panels were welded in place and the panel/shell gap was filled with RTV. Final combustor assembly is in progress. The low pressure cooling subsystem (LPCS) was delivered to the CDIF. Second stage brazing issues were resolved. The construction of the two anode power cabinets was completed.

Not Available

1992-07-01T23:59:59.000Z

317

Working fluids for rankine cycle  

SciTech Connect (OSTI)

This patent describes a method for converting thermal energy into mechanical energy through the utilization of a cycle consisting of: (1) vaporizing, with heating, a mixture selected from the group of (a) 60 to 95% by weight of chlorodifluoromethane and 5 to 40% by weight of difluoroethane; and (b) 3 to 40% by weight of chlorodifluoromethane and 60 to 97% by weight of dichlorotetrafluoroethane; (2) expanding the vapor in an expansion device to produce mechanical energy; and (3) compressing the vapor by a pump and cooling the vapor to condense the vapor.

Enjo, N.; Aomi, H.; Noguchi, M.; Ide, S.

1986-01-07T23:59:59.000Z

318

Rankine cycle system and method  

DOE Patents [OSTI]

A Rankine cycle waste heat recovery system uses a receiver with a maximum liquid working fluid level lower than the minimum liquid working fluid level of a sub-cooler of the waste heat recovery system. The receiver may have a position that is physically lower than the sub-cooler's position. A valve controls transfer of fluid between several of the components in the waste heat recovery system, especially from the receiver to the sub-cooler. The system may also have an associated control module.

Ernst, Timothy C.; Nelson, Christopher R.

2014-09-09T23:59:59.000Z

319

New vortex ring configurations for the MAP dyon solutions  

Science Journals Connector (OSTI)

Electrically charged magnetic solutions of SU (2) Yang-Mills-Higgs theory with net zero topological charge has been obtained as axially symmetric saddle-point solutions in Ref. [1]. These solutions are characterized by an integer the winding number n of their azimuthal angle ? and an electric charge parameter 0ring configuration with n=2 ?=0.65 and varying Higgs field strength. Our observations showed that beside the fundamental solution which is an electrically charged MAP solution there also exist two other branches of eclectically charged vortex ring solutions which both appear at ?=20.45. The difference in total energy between these two branches of solution is very small but the difference in diameter of vortex rings of the two branches is quite significant. Finding of a branching phenomena in presence of a fundamental MAP solution has been for the first time. In Ref. [2] new branching solutions occur for the electrically neutral case in presence of fundamental vortex ring solutions but not for the fundamental MAP solution.

2014-01-01T23:59:59.000Z

320

Thermal-aware Synthesis of Integrated Photonic Ring Resonators  

E-Print Network [OSTI]

Thermal-aware Synthesis of Integrated Photonic Ring Resonators Christopher Condrat Calypto Design-chip optical-interconnect wavelength division multi- plexing (WDM) network architectures. Thermal interactions literature proposes active compensation for such refractive index variations (e.g. carrier-injection based

Kalla, Priyank

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Apparatus and method for suppressing diffraction rings in a laser  

SciTech Connect (OSTI)

This patent describes a method of manufacturing a gas laser having an envelope for containing a laser gas and a tube in the envelope which surrounds an optical path. The method comprising flowing a substance through the tube to roughen interior surfaces of the tube such that diffraction rings in light output from the laser are suppressed.

Cook, B.H. Jr.

1989-10-10T23:59:59.000Z

322

FRACTIONAL SKEW MONOID RINGS P. ARA, M.A. GONZ  

E-Print Network [OSTI]

FRACTIONAL SKEW MONOID RINGS P. ARA, M.A. GONZ ?? ALEZ­BARROSO, K.R. GOODEARL, AND E. PARDO FQM­298 of the Junta de Andaluc??�a. 1 #12; 2 P. ARA, M.A. GONZ ?? ALEZ­BARROSO, K.R. GOODEARL, AND E

Bigelow, Stephen

323

Depth of Idempotent-Generated Subsemigroups of a Regular Ring  

Science Journals Connector (OSTI)

......Lemma 1.2 applied to the ring eRe shows that y =f\\f2 ...fn+i is a product of n +1 idempotents fx, ...,fn+1 eeRe. Then a = [fx + (1 -- e)][f2 + (1 -- e)]... [fn+i + (1 -- e)\\ is a product of n + 1 idempotents in R......

John Hannah; K. C. O'Meara

1989-11-01T23:59:59.000Z

324

Heartbeat Stars and the Ringing of Tidal Pulsations Kelly Hambleton  

E-Print Network [OSTI]

Heartbeat Stars and the Ringing of Tidal Pulsations Kelly Hambleton Andrej Prsa, Don Kurtz, Jim Fuller, Susan Thompson University of Central Lancashire kmhambleton@uclan.ac.uk March 27, 2014 Kelly 3 Summary Conclusions Future Work Kelly Hambleton (UCLan) Heartbeat Stars March 27, 2014 2 / 33 #12

?umer, Slobodan

325

Muon g-2 ring moving up Illinois river  

SciTech Connect (OSTI)

This clip shows the "Miss Katie" pushing the muon g-2 ring upstream on the Illinois River, and passing through the Peoria Lock and Dam as it travels toward Lemont, where it will be unloaded onto the special Emmert transporter and driven to Fermilab.

none

2013-07-20T23:59:59.000Z

326

Radiation issues in a radioactive ion decay ring  

Science Journals Connector (OSTI)

......disposed of as radioactive waste. Table 3. Specific activity...effective dose per unit release for long-term water releases for two critical...et al. The acceleration and storage of radioactive ions for Neutrino...and 18Ne) circulating in a storage ring. Since the beam is not......

M. Magistris; M. Silari

2005-12-20T23:59:59.000Z

327

A High Density Polarized Hydrogen Gas Target for Storage Rings  

E-Print Network [OSTI]

A High Density Polarized Hydrogen Gas Target for Storage Rings K. Zapfe \\Lambday , B. Braun z , H of gaseous polarized hydrogen was formed by injecting polarized H atoms (produced by Stern­Gerlach spin separation) into a storage cell consisting of a cylindrical tube open at both ends. The target was placed

328

The Lightwave Model 142 CW Visible Ring Laser,  

E-Print Network [OSTI]

, operation temperature was controlled using a diode thermo-electric cooler. The laser specifications [4] were1 The Lightwave Model 142 CW Visible Ring Laser, Beam Splitter, Model ATM- 80A1 Acousto Dr. Andres LaRosa March 11th , 2003 #12;2 Abstract A Lightwave Electronics Model 142 continuous wave

La Rosa, Andres H.

329

The Lightwave Model 142 CW Visible Ring Laser,  

E-Print Network [OSTI]

, operation temperature was controlled using a diode thermo-electric cooler. The laser specifications [4] were1 The Lightwave Model 142 CW Visible Ring Laser, Beam Splitter, Model ATM- 80A1 Acousto Dr. Andres LaRosa Abstract A Lightwave Electronics Model 142 continuous wave visible (green) laser

La Rosa, Andres H.

330

The domination of Saturn's low latitude ionosphere by ring `rain'  

E-Print Network [OSTI]

Saturn's ionosphere is produced when the otherwise neutral atmosphere is exposed to a flow of energetic charged particles or solar radiation. At low latitudes the latter should result in a weak planet-wide glow in infrared (IR), corresponding to the planet's uniform illumination by the Sun. The observed low-latitude ionospheric electron density is lower and the temperature higher than predicted by models. A planet-ring magnetic connection has been previously suggested in which an influx of water from the rings could explain the lower than expected electron densities in Saturn's atmosphere. Here we report the detection of a pattern of features, extending across a broad latitude band from ~25 to 60 degrees, that is superposed on the lower latitude background glow, with peaks in emission that map along the planet's magnetic field lines to gaps in Saturn's rings. This pattern implies the transfer of charged water products from the ring-plane to the ionosphere, revealing the influx on a global scale, flooding betw...

O'Donoghue, J; Melin, H; Jones, G H; Cowley, S W H; Miller, S; Baines, K H; Blake, J S D

2013-01-01T23:59:59.000Z

331

WEAK SUBINTEGRALITY AND INVERTIBLE MODULES IN GRADED RINGS  

E-Print Network [OSTI]

WEAK SUBINTEGRALITY AND INVERTIBLE MODULES IN GRADED RINGSB=A : B=A ! I (A?, B?). Here A? is the divided power algebra associated with A, which is the ring having, then the homomorphism iB=A : B=A ! I (A?, B?) is an isomorphism. A key new observation used in the proof

Roberts, Leslie

332

Persistent Ring Currents in an Ideal Bose Gas  

Science Journals Connector (OSTI)

......density of supercurrent, is, to applied electric and magnetic fields, namely curl (Ajs...would die down quickly, due to Ohmic resistance, and the :flux through the ring would...attributed to the impossibility of creating elementary excitations which would slow down this......

J. M. Blatt

1961-11-01T23:59:59.000Z

333

Ring current intensity estimated from low-altitude proton observations  

E-Print Network [OSTI]

. Oksavik Department of Physics, University of Bergen, Bergen, Norway D. S. Evans NOAA Space Environment as a proxy for estimating the energy injection rate into the ring current (RC) due to energetic protons. The injection rate Q(t) is not based upon solar wind parameters but directly on the observed proton

Bergen, Universitetet i

334

An introduction to the Kalina cycle  

SciTech Connect (OSTI)

This paper is intended as a primer on the Kalina cycle--a novel, efficient power cycle that uses an ammonia-water mixture as the working fluid. The reader needs no more than a basic understanding of conventional water based Rankine cycle power plants to comprehend the basic thermodynamics, principles and arrangements of Kalina cycle power plants presented in this paper. The Kalina cycle is principally a modified Rankine cycle. The transformation starts with an important process change to the Rankine cycle--changing the working fluid in the cycle from a pure component (typically water) to a mixture of ammonia and water. The modifications that complete the transformation of the cycle from Rankine to Kalina consist of proprietary system designs that specifically exploit the virtues of the ammonia-water working fluid. These special designs, either applied individually or integrated together in a number of different combinations, comprise a family of unique Kalina cycle systems. This is somewhat analogous to the Rankine cycle which, in fact, has many design options such as reheat, regenerative heating, supercritical pressure, dual pressure, etc. all of which can be applied in a number of different combinations in a particular plant.

Micak, H.A.

1996-12-31T23:59:59.000Z

335

Fuel Cycle CrossCut Group  

Broader source: Energy.gov (indexed) [DOE]

CrossCut Group CrossCut Group 1 NERAC Briefing: Assessment of Dose of Closed vs Open Gen-IV Fuel Cycles David Wade NERAC Meeting September 30, 2002 Fuel Cycle CrossCut Group 2 Public Dose and Worker Dose Comparison of Open vs Closed Fuel Cycles * Gen-IV fuel cycle options are meant to address all stated Gen-IV Goals - Dose to workers and to the public is one of the numerous elements to be evaluated by Gen-IV R&D - The Fuel Cycle Crosscut Group was assigned to take an early look at dose implication tradeoffs of open and closed fuel cycles * FCCG Interpretation of Assignment: - Collect already-existing evaluations and prepare a briefing on what is currently known Fuel Cycle CrossCut Group 3 Approach * Look at Actual Historical Doses Based on Operational Experience - Data compiled by the United Nations Scientific Committee on the Effects of Atomic

336

VISION: Verifiable Fuel Cycle Simulation Model  

SciTech Connect (OSTI)

The nuclear fuel cycle is a very complex system that includes considerable dynamic complexity as well as detail complexity. In the nuclear power realm, there are experts and considerable research and development in nuclear fuel development, separations technology, reactor physics and waste management. What is lacking is an overall understanding of the entire nuclear fuel cycle and how the deployment of new fuel cycle technologies affects the overall performance of the fuel cycle. The Advanced Fuel Cycle Initiatives systems analysis group is developing a dynamic simulation model, VISION, to capture the relationships, timing and delays in and among the fuel cycle components to help develop an understanding of how the overall fuel cycle works and can transition as technologies are changed. This paper is an overview of the philosophy and development strategy behind VISION. The paper includes some descriptions of the model and some examples of how to use VISION.

Jacob J. Jacobson; Abdellatif M. Yacout; Gretchen E. Matthern; Steven J. Piet; David E. Shropshire

2009-04-01T23:59:59.000Z

337

Definition: Brayton cycle | Open Energy Information  

Open Energy Info (EERE)

form form View source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Definition Edit with form History Facebook icon Twitter icon » Definition: Brayton cycle Jump to: navigation, search Dictionary.png Brayton cycle A thermodynamic cycle using constant pressure, heat addition and rejection. Fuel and a compressor are used to heat and increase the pressure of a gas; the gas expands and spins the blades of a turbine, which, when connected to a generator, generates electricity.[1][2] View on Wikipedia Wikipedia Definition The Brayton cycle is a thermodynamic cycle that describes the workings of a constant pressure heat engine. Gas turbine engines and airbreathing jet engines use the Brayton Cycle. Although the Brayton cycle

338

Fuel Cycle Research and Development Program  

Broader source: Energy.gov (indexed) [DOE]

Development Program Presentation to Office of Environmental Management Tank Waste Corporate Board James C. Bresee, ScD, JD Advisory Board Member Office of Nuclear Energy July 29, 2009 July 29, 2009 Fuel Cycle Research and Development DM 195665 2 Outline Fuel Cycle R&D Mission Changes from the Former Advanced Fuel Cycle Initiative The Science-Based Approach Key Collaborators Budget History Program Elements Summary July 29, 2009 Fuel Cycle Research and Development DM 195665 3 Fuel Cycle R&D Mission The mission of Fuel Cycle Research and Development is to develop options to current fuel cycle management strategy to enable the safe, secure, economic, and sustainable expansion of nuclear energy while reducing proliferation risks by conducting

339

Microwave imaging of Saturn's deep atmosphere and rings  

SciTech Connect (OSTI)

An analysis of microwave images of Saturn's atmosphere and rings is presented. Interferometer observations at wavelengths of 0.27, 2.01, 6.17, and 20.13 cm, and precise application of synthesis imaging techniques yielded brightness and polarization maps of unsurpassed resolution and sensitivity. Linear polarization is detected from the ring ansea, and brightness variations in the deep atmosphere and the rings are revealed. The disk-integrated spectrum of Saturn is interpreted within the context of a radiative transfer model that requires the NH{sub 3} mixing ratio to take on a value of 0.9 to 1.1 x 10{sup -} directly below the ammonia ice cloud at a pressure of 1.4 bar. The NH{sub 3} mixing ratio increases with depth to a value of 5.0 to 6.5 x 10{sup -} at a pressure of 6 bar. The variation of NH{sub 3} with depth can be entirely accounted for by the presence of 11 to 14 times solar abundance of H{sub 2}S, which reacts with NH{sub 3} to produce a substantial NH{sub 4}SH cloud. Latitudinal variations in brightness temperature indicate that the saturated vapor abundance of ammonia decreases by 50 percent from equator to pole within the cloud deck. At greater depths, the latitudinal variations of ammonia are consistent with alternating zones of concentration and depletion caused by vertical motions. An apparent depletion in northern mid-lattitudes is well-correlated with a decrease in infrared opacity and depressed cloud top levels, indicating deep-seated downwelling. The size, composition, and shape of particles comprising the rings of Saturn are constrained by modeling the emission, scattering, and extinction of radiation by the rings. Azimuthal variations in brightness and linear polarization favor a model in which the particles are irregularly shaped.

Grossman, A.W.

1990-01-01T23:59:59.000Z

340

MHD Integrated Topping Cycle Project  

SciTech Connect (OSTI)

The overall objective of the project is to design and construct prototypical hardware for an integrated MHD topping cycle, and conduct long duration proof-of-concept tests of integrated system at the US DOE Component Development and Integration Facility in Butte, Montana. The results of the long duration tests will augment the existing engineering design data base on MHD power train reliability, availability, maintainability, and performance, and will serve as a basis for scaling up the topping cycle design to the next level of development, an early commercial scale power plant retrofit. The components of the MHD power train to be designed, fabricated, and tested include: A slagging coal combustor with a rated capacity of 50 MW thermal input, capable of operation with an Eastern (Illinois {number sign}6) or Western (Montana Rosebud) coal, a segmented supersonic nozzle, a supersonic MHD channel capable of generating at least 1.5 MW of electrical power, a segmented supersonic diffuser section to interface the channel with existing facility quench and exhaust systems, a complete set of current control circuits for local diagonal current control along the channel, and a set of current consolidation circuits to interface the channel with the existing facility inverter.

Not Available

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

MHD Integrated Topping Cycle Project  

SciTech Connect (OSTI)

The Magnetohydrodynamics (MHD) Integrated Topping Cycle (ITC) Project represents the culmination of the proof-of-concept (POC) development stage in the US Department of Energy (DOE) program to advance MHD technology to early commercial development stage utility power applications. The project is a joint effort, combining the skills of three topping cycle component developers: TRW, Avco/TDS, and Westinghouse. TRW, the prime contractor and system integrator, is responsible for the 50 thermal megawatt (50 MW{sub t}) slagging coal combustion subsystem. Avco/TDS is responsible for the MHD channel subsystem (nozzle, channel, diffuser, and power conditioning circuits), and Westinghouse is responsible for the current consolidation subsystem. The ITC Project will advance the state-of-the-art in MHD power systems with the design, construction, and integrated testing of 50 MW{sub t} power train components which are prototypical of the equipment that will be used in an early commercial scale MHD utility retrofit. Long duration testing of the integrated power train at the Component Development and Integration Facility (CDIF) in Butte, Montana will be performed, so that by the early 1990's, an engineering data base on the reliability, availability, maintainability and performance of the system will be available to allow scaleup of the prototypical designs to the next development level. This Sixteenth Quarterly Technical Progress Report covers the period May 1, 1991 to July 31, 1991.

Not Available

1992-03-01T23:59:59.000Z

342

Modeling and simulation of longitudinal dynamics for Low Energy RingHigh Energy Ring at the Positron-Electron Project  

Science Journals Connector (OSTI)

A time domain dynamic modeling and simulation tool for beam-cavity interactions in the Low Energy Ring (LER) and High Energy Ring (HER) at the Positron-Electron Project (PEP-II) is presented. Dynamic simulation results for PEP-II are compared to measurements of the actual machine. The motivation for this tool is to explore the stability margins and performance limits of PEP-II radio-frequency (RF) systems at future higher currents and upgraded RF configurations. It also serves as a test bed for new control algorithms and can define the ultimate limits of the low-level RF (LLRF) architecture. The time domain program captures the dynamic behavior of the beam-cavity-LLRF interaction based on a reduced model. The ring current is represented by macrobunches. Multiple RF stations in the ring are represented via one or two macrocavities. Each macrocavity captures the overall behavior of all the 2 or 4 cavity RF stations. Station models include nonlinear elements in the klystron and signal processing. This enables modeling the principal longitudinal impedance control loops interacting via the longitudinal beam model. The dynamics of the simulation model are validated by comparing the measured growth rates for the LER with simulation results. The simulated behavior of the LER at increased operation currents is presented via low-mode instability growth rates. Different control strategies are compared and the effects of both the imperfections in the LLRF signal processing and the nonlinear drivers and klystrons are explored.

C. Rivetta; T. Mastorides; J. D. Fox; D. Teytelman; D. Van Winkle

2007-02-21T23:59:59.000Z

343

Improved temperature regulation of process water systems for the APS storage ring.  

SciTech Connect (OSTI)

Beam stability and operational reliability of critical mechanical systems are key performance issues for synchrotron accelerators such as the Advanced Photon Source (APS). Stability is influenced by temperature fluctuations of the process water (PW) used for cooling and/or temperature conditioning storage ring (SR) components such as vacuum chambers, magnets, absorbers, etc. Operational reliability is crucial in maintaining facility beam operations and remaining within downtime ''budgets.'' Water systems for the APS storage ring were originally provided with a distributive control system (DCS) capable of regulation to {+-}1.0 F, as specified by facility design requirements. After several years of operation, a particular mode of component mortality indicated a need for upgrade of the temperature control system. The upgrade that was implemented was chosen for both improved component reliability and temperature stability (now on the order of {+-}0.2 F for copper components and {+-}0.05 F for aluminum components). The design employs a network of programmable logic controllers (PLCs) for temperature control that functions under supervision of the existing DCS. The human-machine interface (HMI) of the PLC system employs RSView32 software. The PLC system also interfaces with the EPICS accelerator control system to provide monitoring of temperature control parameters. Eventual supervision of the PLC system by EPICS is possible with this design.

Putnam, C.; Dortwegt, R.

2002-10-10T23:59:59.000Z

344

Modeling the lubrication of the piston ring pack in internal combustion engines using the deterministic method  

E-Print Network [OSTI]

Piston ring packs are used in internal combustion engines to seal both the high pressure gas in the combustion chamber and the lubricant oil in the crank case. The interaction between the piston ring pack and the cylinder ...

Chen, Haijie

2011-01-01T23:59:59.000Z

345

Effects of lubricant viscosity and surface texturing on ring-pack performance in internal combustion engines  

E-Print Network [OSTI]

The piston ring-pack contributes approximately 25% of the mechanical losses in an internal combustion engine. Both lubricant viscosity and surface texturing were investigated in an effort to reduce this ring-pack friction ...

Takata, Rosalind (Rosalind Kazuko), 1978-

2006-01-01T23:59:59.000Z

346

Prediction and measurement of the rotordynamic response of an automotive turbocharger with floating ring bearings  

E-Print Network [OSTI]

of lubricant heating and bearing clearance changes due to bearing power consumption. The floating ring bearing analysis provides both floating ring speeds and bearing force coefficients for use in a linear rotordynamic model. The linear rotordynamic...

Kerth, Jason Michael

2012-06-07T23:59:59.000Z

347

The walled city : Beijing hybrid development plan in the 2nd ring road  

E-Print Network [OSTI]

The circular ring roads are one of the key elements that define the spatial organization of Beijing today. However, as the city continues to expand, the ring roads located in the inner city, combined with the gridded ...

Liang, Shaoyi

2014-01-01T23:59:59.000Z

348

Air flow effects in the piston ring pack and their implications on oil transport  

E-Print Network [OSTI]

3 different flow regimes of piston blowby air and their influences on oil transport are studied. It is found that air mainly interacts with oil close to the ring gaps and directly below the ring-liner contacts. Geometric ...

Wang, Yuan, S.M. Massachusetts Institute of Technology

2012-01-01T23:59:59.000Z

349

The effect of surface finish on piston ring-pack performance in advanced reciprocating engine systems  

E-Print Network [OSTI]

Frictional losses in the piston ring-pack of an engine account for approximately 20% of the total frictional losses within an engine. Methods of surface texture optimization were investigated to reduce piston ring-pack ...

Jocsak, Jeffrey (Jeffrey Alan)

2005-01-01T23:59:59.000Z

350

The Seasonal Cycle over the United States and Mexico  

Science Journals Connector (OSTI)

The annual cycle occupies a unique position in the spectra of meteorological time series. This cycle and its first three harmonics are extracted from the series as a seasonal cycle. The distributions of the annual and seasonal cycles are studied ...

Vernon E. Kousky; S. Srivatsangam

1983-01-01T23:59:59.000Z

351

The Geographic Distribution, Genetic Structure and Cultural Management of Waitea circinata var. circinata, the Causal Agent of Brown Ring Patch  

E-Print Network [OSTI]

M. 2005. Brown ring patch: A new disease on bentgrass causedM. 2005. Brown ring patch: A new disease on bentgrass causedfor the control of brown ring patch in southern California,

CHEN, CHIMIN

2011-01-01T23:59:59.000Z

352

AN EXAMPLE OF A NICE VARIETY WHOSE RING OF GLOBAL SECTIONS IS NOT FINITELY GENERATED  

E-Print Network [OSTI]

generated. Now let X be the total space of the vector bundle N P over E. Then the ring of global sectionsAN EXAMPLE OF A NICE VARIETY WHOSE RING OF GLOBAL SECTIONS IS NOT FINITELY GENERATED RAVI VAKIL 1 ring of global sections. I certainly thought this. Brian Osserman asked about this in the introductory

Vakil, Ravi

353

Self-Assembly in Chains, Rings, and Branches: A Single Component System with Two Critical Points  

E-Print Network [OSTI]

Self-Assembly in Chains, Rings, and Branches: A Single Component System with Two Critical Points October 2013) We study the interplay between phase separation and self-assembly in chains, rings. The emergence of the lower critical point is caused by the self-assembly of rings taking place in the vapor

Sciortino, Francesco

354

Penetration of plasma into the wafer-focus ring gap in capacitively coupled plasmas  

E-Print Network [OSTI]

Penetration of plasma into the wafer-focus ring gap in capacitively coupled plasmas Natalia Y of capacitively coupled plasma reactors with a wafer-focus ring gap. The penetration of plasma generated species i.e., ions and radicals into the wafer-focus ring gap is discussed. We found that the penetration of plasma

Kushner, Mark

355

The 3-Sphere and the Bicycling Black Rings Event Horizon The 3-Sphere and the Bicycling  

E-Print Network [OSTI]

The 3-Sphere and the Bicycling Black Rings Event Horizon #12;#12;The 3-Sphere and the Bicycling that "the bicycling black rings" are a admissible solution to the event horizon of black holes in 4 is to develop a method of visualising the bicycling black rings and other four-dimensional objects. In the end

Bengtsson, Ingemar

356

MHD Integrated Topping Cycle Project  

SciTech Connect (OSTI)

This seventeenth quarterly technical progress report of the MHD Integrated Topping Cycle Project presents the accomplishments during the period August 1, 1991 to October 31, 1991. Manufacturing of the prototypical combustor pressure shell has been completed including leak, proof, and assembly fit checking. Manufacturing of forty-five cooling panels was also completed including leak, proof, and flow testing. All precombustor internal components (combustion can baffle and swirl box) were received and checked, and integration of the components was initiated. A decision was made regarding the primary and backup designs for the 1A4 channel. The assembly of the channel related prototypical hardware continued. The cathode wall electrical wiring is now complete. The mechanical design of the diffuser has been completed.

Not Available

1992-07-01T23:59:59.000Z

357

Efficiency combined cycle power plant  

SciTech Connect (OSTI)

This patent describes a method of operating a combined cycle power plant. It comprises: flowing exhaust gas from a combustion turbine through a heat recovery steam generator (HRSG); flowing feed water through an economizer section of the HRSG at a flow rate and providing heated feed water; flowing a first portion of the heated feed water through an evaporator section of the HRSG and producing saturated steam at a production rate, the flow rate of the feed water through the economizer section being greater than required to sustain the production rate of steam in the evaporator section; flowing fuel for the turbine through a heat exchanger; and, flowing a second portion of the heated feed water provided by the economizer section through the heat exchanger then to an inlet of the economizer section, thereby heating the fuel flowing through the heat exchanger.

Pavel, J.; Meyers, G.A.; Baldwin, T.S.

1990-06-12T23:59:59.000Z

358

2D representation of life cycle greenhouse gas emission and life cycle cost of energy conversion for various energy resources  

Science Journals Connector (OSTI)

We suggest a 2D-plot representation combined with life cycle greenhouse gas (GHG) emissions and life cycle cost for various energy conversion technologies. In general, life cycle ... use life cycle GHG emissions ...

Heetae Kim; Claudio Tenreiro; Tae Kyu Ahn

2013-10-01T23:59:59.000Z

359

Nuclear Fuel Cycle | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Cycle Cycle Nuclear Fuel Cycle This is an illustration of a nuclear fuel cycle that shows the required steps to process natural uranium from ore for preparation for fuel to be loaded in nuclear reactors. This is an illustration of a nuclear fuel cycle that shows the required steps to process natural uranium from ore for preparation for fuel to be loaded in nuclear reactors. The mission of NE-54 is primarily focused on activities related to the front end of the nuclear fuel cycle which includes mining, milling, conversion, and enrichment. Uranium Mining Both "conventional" open pit, underground mining, and in situ techniques are used to recover uranium ore. In general, open pit mining is used where deposits are close to the surface and underground mining is used

360

NREL: Energy Analysis - Life Cycle Assessment Harmonization  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Life Cycle Assessment Harmonization Life Cycle Assessment Harmonization Life Cycle Greenhouse Gas Emissions from Electricity Generation (Fact Sheet) Cover of the Life Cycle Greenhouse Gas Emissions from Electricity Generation factsheet Download the Fact Sheet The U.S. Department of Energy enlisted NREL to review and "harmonize" life cycle assessments (LCA) of electricity generation technologies. Hundreds of assessments have been published, often with considerable variability in results. These variations in approach, while usually legitimate, hamper comparison across studies and pooling of published results. Learn more about life cycle assessments of energy technologies. By harmonizing this data, NREL seeks to reduce the uncertainty around estimates for environmental impacts of renewables and increase the value of

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Definition: Thermodynamic cycle | Open Energy Information  

Open Energy Info (EERE)

Thermodynamic cycle Thermodynamic cycle Jump to: navigation, search Dictionary.png Thermodynamic cycle A process in which a fluid (water, air, ammonia, etc) successively changes state (from a liquid to a gas and back to a liquid) for the purpose of producing or transferring energy.[1] View on Wikipedia Wikipedia Definition A thermodynamic cycle consists of a collection of thermodynamic processes transferring heat and work, while varying pressure, temperature, and other state variables, eventually returning a system to its initial state. In the process of going through this cycle, the system may perform work on its surroundings, therefore acting as a heat engine. State quantities depend only on the thermodynamic state, and cumulative variation of such properties adds up to zero during a cycle. Process quantities (or

362

LARSON--MATH 556--CLASSROOM WORKSHEET 07 Hamilton Cycles  

E-Print Network [OSTI]

Last name First name LARSON--MATH 556--CLASSROOM WORKSHEET 07 Hamilton Cycles An alternating-cycle. A cycle which includes every point of a graph G is called a Hamilton cycle of G. 1. Draw the complete graph K5. Find one Hamilton cycle in K5. 2. Does every complete graph have a Hamilton cycle? Explain. 3

Larson, Craig E.

363

Michigan Math. J. 52 (2004) Cycles over Fields of Transcendence Degree 1  

E-Print Network [OSTI]

. For a smooth vari- ety V over k, the Chow group of cycles of codimension p is defined (see [F]) as CHp (V function on it. There is a natural cycle class map clp : CHp (V ) H2p (V ), where the latter denotes]). The kernel of clp is denoted by F1 CHp (V ). There is an Abel­Jacobi map (see [G]) p : F1 CHp (V ) IJp (H2p

364

Multiple Rankine topping cycles offer high efficiency  

SciTech Connect (OSTI)

The efficiency of a Rankine cycle is primarily determined by the temperatures of heat addition and heat rejection. However, no working fluid has been identified that will operate in a Rankine cycle over an extremely wide temperature range. Multiple Rankine topping cycles offer a technique for achieving high thermal efficiencies in power plants by allowing the use of several working fluids to span larger temperature ranges.

McWhirter, J.D. [Idaho State Univ., Pocatello, ID (United States)

1997-10-01T23:59:59.000Z

365

Functionalized apertures for the detection of chemical and biological materials  

DOE Patents [OSTI]

Disclosed are nanometer to micron scale functionalized apertures constructed on a substrate made of glass, carbon, semiconductors or polymeric materials that allow for the real time detection of biological materials or chemical moieties. Many apertures can exist on one substrate allowing for the simultaneous detection of numerous chemical and biological molecules. One embodiment features a macrocyclic ring attached to cross-linkers, wherein the macrocyclic ring has a biological or chemical probe extending through the aperture. Another embodiment achieves functionalization by attaching chemical or biological anchors directly to the walls of the apertures via cross-linkers.

Letant, Sonia E. (Livermore, CA); van Buuren, Anthony W. (Livermore, CA); Terminello, Louis J. (Danville, CA); Thelen, Michael P. (Danville, CA); Hope-Weeks, Louisa J. (Brentwood, CA); Hart, Bradley R. (Brentwood, CA)

2010-12-14T23:59:59.000Z

366

Twisted Electromagnetic Modes and Sagnac Ring-Lasers  

E-Print Network [OSTI]

A new approximation scheme, designed to solve the covariant Maxwell equations inside a rotating hollow slender conducting cavity (modelling a ring-laser), is constructed. It is shown that for well-defined conditions there exist TE and TM modes with respect to the longitudinal axis of the cavity. A twisted mode spectrum is found to depend on the integrated Frenet torsion of the cavity and this in turn may affect the Sagnac beat frequency induced by a non-zero rotation of the cavity. The analysis is motivated by attempts to use ring-lasers to measure terrestrial gravito-magnetism or the Lense-Thirring effect produced by the rotation of the Earth.

David A. Burton; Adam Noble; Robin W. Tucker; David L. Wiltshire

2004-11-08T23:59:59.000Z

367

PCM energy storage during defective thermal cycling:.  

E-Print Network [OSTI]

??Incomplete thermal cycling affects storage capacities of phase change materials (PCMs). Existing PCM measuring methods are presented with their drawbacks. A new device named the (more)

Koekenbier, S.F.

2011-01-01T23:59:59.000Z

368

Life Cycle Assessment of Biomass Conversion Pathways.  

E-Print Network [OSTI]

??This study has investigated the life cycle of three biomass feedstocks including forest residue, agricultural residue, and whole forest for biohydrogen and biopower production in (more)

Kabir, Md R

2012-01-01T23:59:59.000Z

369

Variable pressure power cycle and control system  

DOE Patents [OSTI]

A variable pressure power cycle and control system that is adjustable to a variable heat source is disclosed. The power cycle adjusts itself to the heat source so that a minimal temperature difference is maintained between the heat source fluid and the power cycle working fluid, thereby substantially matching the thermodynamic envelope of the power cycle to the thermodynamic envelope of the heat source. Adjustments are made by sensing the inlet temperature of the heat source fluid and then setting a superheated vapor temperature and pressure to achieve a minimum temperature difference between the heat source fluid and the working fluid.

Goldsberry, Fred L. (Spring, TX)

1984-11-27T23:59:59.000Z

370

Tropical Cloud Life Cycle and Overlap Structure  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Tropical Cloud Life Cycle and Overlap Structure Vogelmann, Andrew Brookhaven National Laboratory Jensen, Michael Brookhaven National Laboratory Kollias, Pavlos Brookhaven National...

371

Splitting the Cycle the Right Way  

Broader source: Energy.gov [DOE]

The unique opposed-cylinder configuration of the TourEngine allows superior thermal management and efficient gas transfer compared to other split-cycle designs.

372

THE TRANSPOSED CRITICAL TEMPERATURE RANKINE THERMODYNAMIC CYCLE  

E-Print Network [OSTI]

of Electricity from Geothermal Energy," Brown University,Simulation of Geothermal Energy Cycles), LBL publication-Manager), Economics "Geothermal Energy Conversion and Case

Pope, William L.

2012-01-01T23:59:59.000Z

373

Fuel Cycle Research and Development Program  

Office of Environmental Management (EM)

29, 2009 Fuel Cycle Research and Development DM 195665 5 Identify the governing phenomenology Identify the governing phenomenology Develop a first-principle based model of the...

374

Magnetic field control of the intraband optical absorption in two-dimensional quantum rings  

SciTech Connect (OSTI)

Linear and nonlinear optical absorption coefficients of the two-dimensional semiconductor ring in the perpendicular magnetic field B are calculated within independent electron approximation. Characteristic feature of the energy spectrum are crossings of the levels with adjacent nonpositive magnetic quantum numbers as the intensity B changes. It is shown that the absorption coefficient of the associated optical transition is drastically decreased at the fields corresponding to the crossing. Proposed model of the Volcano disc allows to get simple mathematical analytical results, which provide clear physical interpretation. An interplay between positive linear and intensity-dependent negative cubic absorption coefficients is discussed; in particular, critical light intensity at which additional resonances appear in the total absorption dependence on the light frequency is calculated as a function of the magnetic field and levels' broadening.

Olendski, O., E-mail: oolendski@ksu.edu.sa [King Abdullah Institute for Nanotechnology, King Saud University, P.O. Box 2454, Riyadh 11451 (Saudi Arabia); Barakat, T., E-mail: tbarakat@ksu.edu.sa [Department of Physics, King Saud University, P.O. Box 2454, Riyadh 11451 (Saudi Arabia)

2014-02-28T23:59:59.000Z

375

Bichromatic emission and multimode dynamics in bidirectional ring lasers  

SciTech Connect (OSTI)

The multimode dynamics of a two-level ring laser is explored numerically using a bidirectional traveling wave model retaining the spatial effects due to the presence of counter-propagating electric fields in the population inversion. Dynamical regimes where the emission in each direction occurs at different wavelengths are studied. Mode-locked unidirectional emission for large gain bandwidth and relatively small detuning is reported.

Perez-Serrano, Antonio; Javaloyes, Julien; Balle, Salvador [Instituto de Fisica Interdisciplinar y Sistemas Complejos, IFISC, UIB-CSIC, Campus UIB, Palma de Mallorca, E-07122 (Spain); Department of Electronics and Electrical Engineering, University of Glasgow, Glasgow, G12 8LT (United Kingdom); Institut Mediterrani d'Estudis Avancats, IMEDEA, UIB-CSIC, Esporles, E-07190 (Spain)

2010-04-15T23:59:59.000Z

376

Quantum interference in an electron-hole graphene ring system  

SciTech Connect (OSTI)

Quantum interference is observed in a graphene ring system via the Aharonov Bohm effect. As graphene is a gapless semiconductor, this geometry allows to study the unique situation of quantum interference between electrons and holes in addition to the unipolar quantum interference. The period and amplitude of the observed Aharonov-Bohm oscillations are independent of the sign of the applied gate voltage showing the equivalence between unipolar and dipolar interference.

Smirnov, D.; Schmidt, H.; Haug, R. J. [Institut fr Festkrperphysik, Leibniz Universitt Hannover, Appelstr. 2 30167 Hannover (Germany)

2013-12-04T23:59:59.000Z

377

STATUS REPORT FOR AGING STUDIES OF EPDM O-RING MATERIAL FOR THE H1616 SHIPPING PACKAGE  

SciTech Connect (OSTI)

This is an interim status report for tasks carried out per Task Technical Plan SRNL-STI-2011-00506. A series of tasks/experiments are being performed at the Savannah River National Laboratory to monitor the aging performance of ethylene propylene diene monomer (EPDM) Orings used in the H1616 shipping package. The data will support the technical basis to extend the annual maintenance of the EPDM O-rings in the H1616 shipping package and to predict the life of the seals at bounding service conditions. Current expectations are that the O-rings will maintain a seal at bounding normal temperatures in service (152 F) for at least 12 months. The baseline aging data review suggests that the EPDM O-rings are likely to retain significant mechanical properties and sealing force at bounding service temperatures to provide a service life of at least 2 years. At lower, more realistic temperatures, longer service life is likely. Parallel compression stress relaxation and vessel leak test efforts are in progress to further validate this assessment and quantify a more realistic service life prediction. The H1616 shipping package O-rings were evaluated for baseline property data as part of this test program. This was done to provide a basis for comparison of changes in material properties and performance parameters as a function of aging. This initial characterization was limited to physical and mechanical properties, namely hardness, thickness and tensile strength. These properties appear to be consistent with O-ring specifications. Three H1616-1 Containment Vessels were placed in test conditions and are aging at temperatures ranging from 160 to 300 F. The vessels were Helium leak-tested initially and have been tested at periodic intervals after cooling to room temperature to determine if they meet the criterion of leaktightness defined in ANSI standard N14.5-97 (< 1E-07 std cc air/sec at room temperature). To date, no leak test failures have occurred. The cumulative time at temperature ranges from 174 days for the 300 F vessel to 189 days for the 160 F vessel as of 8/1/2012. The compression stress-relaxation (CSR) behavior of H1616 shipping package O-rings is being evaluated to develop an aging model based on material properties. O-ring segments were initially aged at four temperatures (175 F, 235 F, 300 F and 350 F). These temperatures were selected to bound normal service temperatures and to challenge the seals within a reasonable aging period. Currently, samples aging at 300 F and 350 F have reached the mechanical failure point (end of life) which is defined in this study as 90% loss of initial sealing force. As a result, additional samples more recently began aging at {approx}270 F to provide additional data for the aging model. Aging and periodic leak testing of the full containment vessels, as well as CSR testing of O-ring segments is ongoing. Continued testing per the Task Technical Plan is recommended in order to validate the assumptions outlined in this status report and to quantify and validate the long-term performance of O-ring seals under actual service conditions.

Stefek, T.; Daugherty, W.; Skidmore, E.

2012-08-31T23:59:59.000Z

378

Norbornene-Functionalized Diblock Copolymers via Ring-Opening Metathesis Polymerization for Magnetic Nanoparticle Stabilization  

Science Journals Connector (OSTI)

(6)?Hinds, K. A.; Hill, J. M.; Shapiro, E. M.; Laukkanen, M. O.; Silva, A. C.; Varney, T. R.; Balaban, R. S.; Koretsky, A. P.; Dunbar, C. E. Blood 2003, 102, 867. ... Hinds, Kathleen A.; Hill, Jonathan M.; Shapiro, Erik M.; Laukkanen, Mikko O.; Silva, Alfonso C.; Combs, Christian A.; Varney, Timothy R.; Balaban, Robert S.; Koretsky, Alan P.; Dunbar, Cynthia E. ...

Kevin D. Belfield; Li Zhang

2006-11-15T23:59:59.000Z

379

Concepts and performance for a next-generation storage ring hard x-ray source  

SciTech Connect (OSTI)

Among the possibilities for a next-generation hard x-ray source is a so-called 'ultimate storage ring'. This refers to a large, high-energy storage ring with very low emittance and high current. Such a ring has the potential to deliver significantly higher spectral brightness and transverse coherence than present third-generation rings. At the same time, it promises the stability and reliability that users have come to expect in a light source. In this paper, we present a design for a 7-GeV, 40-sector storage ring with a circumference of 3.1 km and an emittance of 15 pm in both planes.

Borland, M. [Argonne National Laboratory, Argonne, IL, 60439 (United States)

2010-06-23T23:59:59.000Z

380

Cell cycle and DNA damage response regulation by Spy1, and the intersection of FGFR and NFkappaB pathways  

E-Print Network [OSTI]

Silva LF, Duncker BP. ORC function in late G1: maintaining128-30. DePamphilis ML. The 'ORC cycle': a novel pathway forOrigin Recognition Complex (ORC), cdc6/18, cdc45, cdt1, the

McAndrew, Christopher William

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

The influence of lateral foot displacement on cycling efficiency and maximal cycling power.  

E-Print Network [OSTI]

??HARPER, SARA A., M.S., May 2014Exercise PhysiologyTHE INFLUENCE OF LATERAL PEDAL DISPLACEMENT ON CYCLING EFFICIENCY AND MAXIMAL CYCLING POWER (27 pp.)Director of Thesis: John McDaniel, (more)

Harper, Sara Anne

2014-01-01T23:59:59.000Z

382
383

S and H Cycle Engine  

SciTech Connect (OSTI)

Our thirst for energy is increasing at an astounding rate. World population growth is estimated to increase by 40% (to 8.5 billion) by 2050, with annual electrical energy usage estimated increase by 100% (to 25 terawatt-hours). We must find new means and fuels as well as significantly improve the efficiency of current power plants to accommodate this growing electrical energy demand. This demand is also growing in the field of space flight. Present energy and propulsion systems are limited in the amount of power (energy) that can be generated by today's technology. This limits the distance that can be safely traveled by manned and un-manned space systems. Space flight is primarily governed by two factors: time and energy. Increasing energy of space propulsion systems will decrease flight time or allow reaching farther out into space safely for manned exploration of our solar system. For example, a round trip manned mission to Mars would take about 400 days with a NERVA type thermal nuclear rocket. To reduce the 400 days to 80 days would require an increase of energy by a factor of five. We need to develop space propulsion systems with much greater energy capability than we have today to satisfy the expansion of space exploration. The S and H Cycle nuclear engine provides a revolutionary technological approach that can contribute significantly toward solving the World electrical energy and the space travel energy requirements. (authors)

Strobl, William C. [2906 Via Pepita, Carlsbad, Ca. 92009 (United States); Holland, Joe P. [10671 Jasper Ave., Redlands, Ca. 92374 (United States)

2002-07-01T23:59:59.000Z

384

MHD Integrated Topping Cycle Project  

SciTech Connect (OSTI)

This fourteenth quarterly technical progress report of the MHD Integrated Topping Cycle Project presents the accomplishments during the period November 1, 1990 to January 31, 1991. Testing of the High Pressure Cooling Subsystem electrical isolator was completed. The PEEK material successfully passed the high temperature, high pressure duration tests (50 hours). The Combustion Subsystem drawings were CADAM released. The procurement process is in progress. An equipment specification and RFP were prepared for the new Low Pressure Cooling System (LPCS) and released for quotation. Work has been conducted on confirmation tests leading to final gas-side designs and studies to assist in channel fabrication.The final cathode gas-side design and the proposed gas-side designs of the anode and sidewall are presented. Anode confirmation tests and related analyses of anode wear mechanisms used in the selection of the proposed anode design are presented. Sidewall confirmation tests, which were used to select the proposed gas-side design, were conducted. The design for the full scale CDIF system was completed. A test program was initiated to investigate the practicality of using Avco current controls for current consolidation in the power takeoff (PTO) regions and to determine the cause of past current consolidation failures. Another important activity was the installation of 1A4-style coupons in the 1A1 channel. A description of the coupons and their location with 1A1 channel is presented herein.

Not Available

1992-02-01T23:59:59.000Z

385

Solar cycle changes in coronal holes and space weather cycles J. G. Luhmann,1  

E-Print Network [OSTI]

Solar cycle changes in coronal holes and space weather cycles J. G. Luhmann,1 Y. Li,1 C. N. Arge,2-heliolatitude solar wind over approximately the last three solar cycles. Related key parameters like interplanetary explain solar magnetic field control of long-term interplanetary variations. In particular, the enduring

California at Berkeley, University of

386

Uncertainty Analyses of Advanced Fuel Cycles  

SciTech Connect (OSTI)

The Department of Energy is developing technology, experimental protocols, computational methods, systems analysis software, and many other capabilities in order to advance the nuclear power infrastructure through the Advanced Fuel Cycle Initiative (AFDI). Our project, is intended to facilitate will-informed decision making for the selection of fuel cycle options and facilities for development.

Laurence F. Miller; J. Preston; G. Sweder; T. Anderson; S. Janson; M. Humberstone; J. MConn; J. Clark

2008-12-12T23:59:59.000Z

387

PARAMETRIC CYCLE ANALYSIS FOR PULSE DETONATION ENGINES  

E-Print Network [OSTI]

PARAMETRIC CYCLE ANALYSIS FOR PULSE DETONATION ENGINES by HAIDER HEKIRI Presented to the Faculty, in particular, pulse detonation engines. Dr. Wilson taught me the basics of propulsion and made me enjoy #12;iii ABSTRACT PARAMETRIC CYCLE ANALYSIS FOR PULSE DETONATION ENGINES Publication No. ______ Haider

Texas at Arlington, University of

388

Generating Resources Combined Cycle Combustion Turbine  

E-Print Network [OSTI]

turbine (s) Heat recovery steam generator (s) - HRSG with or without duct firing Natural gas supply11/17/2014 1 Generating Resources Combined Cycle Combustion Turbine Utility Scale Solar PV Steven doing recently around two key supply-side resource technologies 1. Combined Cycle Combustion Turbine

389

mathematics Study program cycle and type  

E-Print Network [OSTI]

mathematics academic study programmm 11 #12;12 #12;· Study program cycle and type: First cycle academic study program. · AAnnttiicciippaatteedd aaccaaddeemmiicc ttiittllee:: Bachelor in Mathematics ggooaallss:: The principal goal of the academic study program in Mathematics is to qualify its graduates

?umer, Slobodan

390

Physics challenges for advanced fuel cycle assessment  

SciTech Connect (OSTI)

Advanced fuel cycles and associated optimized reactor designs will require substantial improvements in key research area to meet new and more challenging requirements. The present paper reviews challenges and issues in the field of reactor and fuel cycle physics. Typical examples are discussed with, in some cases, original results.

Giuseppe Palmiotti; Massimo Salvatores; Gerardo Aliberti

2014-06-01T23:59:59.000Z

391

Life Cycle Assessment: Past, Present, and Future  

Science Journals Connector (OSTI)

Life cycle assessment (LCA) can develop into life cycle sustainability assessment (LCSA), which is a transdisciplinary integration framework of models rather than a model in itself. ... As the environmental burden from agriculture, and especially from livestock breeding, is known to be quite important, such an analysis was interesting for policy purposes. ...

Jeroen B. Guine; Reinout Heijungs; Gjalt Huppes; Alessandra Zamagni; Paolo Masoni; Roberto Buonamici; Tomas Ekvall; Tomas Rydberg

2010-09-02T23:59:59.000Z

392

Fish are crucial in oceanic carbon cycle  

Science Journals Connector (OSTI)

... Fish may play a more important role in the marine carbon cycle than previously thought, ... marine carbon cycle than previously thought, a new study shows. Researchers have found that fish excrete prodigious amounts of a mineral, calcium carbonate, that had been thought to come ...

Roberta Kwok

2009-01-15T23:59:59.000Z

393

An automaton model for the cell cycle  

Science Journals Connector (OSTI)

...the cell cycle phases. Upon completion of the M phase, the cell...appendix A.2). -Upon completion of the M phase, the cell...growth fraction, labeling index, duration of S phase, and...the cell cycle phases. Upon completion of the M phase, the cell...

2011-01-01T23:59:59.000Z

394

Binary Cycle Power Plant | Open Energy Information  

Open Energy Info (EERE)

Binary Cycle Power Plant Binary Cycle Power Plant (Redirected from Binary Cycle Power Plants) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Binary Cycle Power Plant General List of Binary Plants Binary power plant process diagram - DOE EERE 2012 Binary cycle geothermal power generation plants differ from Dry Steam and Flash Steam systems in that the water or steam from the geothermal reservoir never comes in contact with the turbine/generator units. Low to moderately heated (below 400°F) geothermal fluid and a secondary (hence, "binary") fluid with a much lower boiling point that water pass through a heat exchanger. Heat from the geothermal fluid causes the secondary fluid to flash to vapor, which then drives the turbines and subsequently, the generators.

395

Binary Cycle Power Plant | Open Energy Information  

Open Energy Info (EERE)

Binary Cycle Power Plant Binary Cycle Power Plant (Redirected from Binary) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Binary Cycle Power Plant General List of Binary Plants Binary power plant process diagram - DOE EERE 2012 Binary cycle geothermal power generation plants differ from Dry Steam and Flash Steam systems in that the water or steam from the geothermal reservoir never comes in contact with the turbine/generator units. Low to moderately heated (below 400°F) geothermal fluid and a secondary (hence, "binary") fluid with a much lower boiling point that water pass through a heat exchanger. Heat from the geothermal fluid causes the secondary fluid to flash to vapor, which then drives the turbines and subsequently, the generators. Binary cycle power plants are closed-loop systems and virtually nothing

396

NPP and the Global Carbon Cycle  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

the Global Carbon Cycle the Global Carbon Cycle Introduction Photosynthetic carbon fixation comprises a major component of the global carbon cycle. Data on net primary productivity (NPP) may be sparse, but a consistent NPP data set may be used to calibrate, parameterize and evaluate models of terrestrial carbon cycling, as well as for validation of remote sensing data and other applications (identifying trends, investigating biogeochemical processes, etc.). It is also useful to place such data within the context of carbon cycling and carbon storage worldwide. For example: How much carbon exists in the biosphere, and where exactly is it stored? How much is in fossil fuels (coal, oil, gas), and how large are current fossil-fuel emissions? How much is in living biomass (plants/ animals/ humans)?

397

Nuclear Fuel Cycle Integrated System Analysis  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Fuel Cycle Integrated System Analysis Fuel Cycle Integrated System Analysis Abdellatif M. Yacout Argonne National Laboratory Nuclear Engineering Division The nuclear fuel cycle is a complex system with multiple components and activities that are combined to provide nuclear energy to a variety of end users. The end uses of nuclear energy are diverse and include electricity, process heat, water desalination, district heating, and possibly future hydrogen production for transportation and energy storage uses. Components of the nuclear fuel cycle include front end components such as uranium mining, conversion and enrichment, fuel fabrication, and the reactor component. Back end of the fuel cycle include used fuel coming out the reactor, used fuel temporary and permanent storage, and fuel reprocessing. Combined with those components there

398

VISION: Verifiable Fuel Cycle Simulation Model  

SciTech Connect (OSTI)

The nuclear fuel cycle consists of a set of complex components that work together in unison. In order to support the nuclear renaissance, it is necessary to understand the impacts of changes and timing of events in any part of the fuel cycle system. The Advanced Fuel Cycle Initiatives systems analysis group is developing a dynamic simulation model, VISION, to capture the relationships, timing, and changes in and among the fuel cycle components to help develop an understanding of how the overall fuel cycle works. This paper is an overview of the philosophy and development strategy behind VISION. The paper includes some descriptions of the model components and some examples of how to use VISION.

Jacob Jacobson; A. M. Yacout; Gretchen Matthern; Steven Piet; David Shropshire; Tyler Schweitzer

2010-11-01T23:59:59.000Z

399

Pipeline bottoming cycle study. Final report  

SciTech Connect (OSTI)

The technical and economic feasibility of applying bottoming cycles to the prime movers that drive the compressors of natural gas pipelines was studied. These bottoming cycles convert some of the waste heat from the exhaust gas of the prime movers into shaft power and conserve gas. Three typical compressor station sites were selected, each on a different pipeline. Although the prime movers were different, they were similar enough in exhaust gas flow rate and temperature that a single bottoming cycle system could be designed, with some modifications, for all three sites. Preliminary design included selection of the bottoming cycle working fluid, optimization of the cycle, and design of the components, such as turbine, vapor generator and condensers. Installation drawings were made and hardware and installation costs were estimated. The results of the economic assessment of retrofitting bottoming cycle systems on the three selected sites indicated that profitability was strongly dependent upon the site-specific installation costs, how the energy was used and the yearly utilization of the apparatus. The study indicated that the bottoming cycles are a competitive investment alternative for certain applications for the pipeline industry. Bottoming cycles are technically feasible. It was concluded that proper design and operating practices would reduce the environmental and safety hazards to acceptable levels. The amount of gas that could be saved through the year 2000 by the adoption of bottoming cycles for two different supply projections was estimated as from 0.296 trillion ft/sup 3/ for a low supply projection to 0.734 trillion ft/sup 3/ for a high supply projection. The potential market for bottoming cycle equipment for the two supply projections varied from 170 to 500 units of varying size. Finally, a demonstration program plan was developed.

Not Available

1980-06-01T23:59:59.000Z

400

The Function of Marine Critical Transition Zones and the Importance of Sediment Biodiversity  

Science Journals Connector (OSTI)

Estuaries and coastal wetlands are critical transition zones (CTZs) that link land, freshwater habitats, and the sea. CTZs provide essential ecological functions, including decomposition, nutrient cycling, and nu...

Lisa A. Levin; Donald F. Boesch; Alan Covich; Cliff Dahm; Christer Ersus

2001-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

In-Situ Monitoring of Particle Growth at PEMFC Cathode under Accelerated Cycling Conditions  

SciTech Connect (OSTI)

An in-situ method to measure changes in catalyst particle size at the cathode of a proton exchange membrane fuel cell is demonstrated. Synchrotron X-rays, 58 keV, were used to measure the pair distribution function on an operating fuel cell and observe the growth of catalyst particles under accelerated degradation conditions. The stability of Pt/C and PtCo/C with different initial particle sizes was monitored over 3000 potential cycles. The increase in particle size was fit to a linear trend as a function of cycles. The most stable electrocatalyst was found to be the alloyed PtCo with the larger initial particle size.

Billinge S. J.; Redmond, E.L.; Setzler, B.P.; Juhas, P.; Fullera, T.F.

2012-05-01T23:59:59.000Z

402

In-Situ Monitoring of Particle Growth at PEMFC Cathode under Accelerated Cycling Conditions  

SciTech Connect (OSTI)

An in-situ method to measure changes in catalyst particle size at the cathode of a proton exchange membrane fuel cell is demonstrated. Synchrotron X-rays, 58 keV, were used to measure the pair distribution function on an operating fuel cell and observe the growth of catalyst particles under accelerated degradation conditions. The stability of Pt/C and PtCo/C with different initial particle sizes was monitored over 3000 potential cycles. The increase in particle size was fit to a linear trend as a function of cycles. The most stable electrocatalyst was found to be the alloyed PtCo with the larger initial particle size.

Redmond, Erin L.; Setzler, Brian P.; Juhas, Pavol; Billinge, Simon J.L.; Fuller, Thomas F. (GIT); (Columbia)

2012-10-25T23:59:59.000Z

403

Advanced Fuel Cycles Activities in IAEA  

SciTech Connect (OSTI)

Considerable scientific and technical progress in many areas of Partitioning and Transmutation (P and T) has been recognized as probable answers to ever-growing issues threatening sustainability, environmental protection and non-proliferation. These recent global developments such as Russian initiative on Global Nuclear Infrastructure-International Fuel Centre and the US initiative on Global Nuclear Energy Partnership (GNEP) have made advanced fuel cycles as one of the decisive influencing factor for the future growth of nuclear energy. International Atomic Energy Agency has initiated the International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO) with overall objective of bringing together technology holders and technology users to consider jointly the international and national actions required achieving desired innovations in nuclear reactors and fuel cycles. One of the interesting common features of these initiatives (INPRO, GNEP and GNI-IFC) is closed fast reactor fuel cycles and proliferation resistance. Any fuel cycle that integrate P and T into it is also known as 'Advanced Fuel Cycle' (AFC) that could achieve reduction of plutonium and Minor Actinide (MA) elements (namely Am, Np, Cm, etc.). In this regard, some Member States are also evaluating alternative concepts involving the use of thorium fuel cycle, inert-matrix fuel or coated particle fuel. Development of 'fast reactors with closed fuel cycles' would be the most essential step for implementation of P and T. The scale of realization of any AFC depends on the maturity of the development of all these elemental technologies such as recycling MA, Pu as well as reprocessed uranium. In accordance with the objectives of the Agency, the programme B entitled 'Nuclear Fuel cycle technologies and materials' initiated several activities aiming to strengthen the capabilities of interested Member States for policy making, strategic planning, technology development and implementation of safe, reliable, economically efficient, proliferation resistant, environmentally sound and secure nuclear fuel cycle programmes. The paper describes some on-going IAEA activities in the area of: MA-fuel and target, thorium fuel cycle, coated particle fuel, MA-property database, inert matrix fuels, liquid metal cooled fast reactor fuels and fuel cycles, management of reprocessed uranium and proliferation resistance in fuel cycle. (authors)

Nawada, H.P.; Ganguly, C. [Nuclear Fuel Cycle and Materials Section, Division of Nuclear Fuel Cycle and Waste Technology, Department of Nuclear Energy, International Atomic Energy Agency, Vienna (Austria)

2007-07-01T23:59:59.000Z

404

Thermodynamic analysis of adsorption refrigeration cycles  

SciTech Connect (OSTI)

High- and mid-temperature waste heat can be recovered by using existing heat pump technologies. However, heat utilization near environmental temperatures still faces technical hurdles. Silica gel-water adsorption cycles have a distinct advantage over other systems in their ability to be driven by near-ambient temperature heat. Waste heat (above 60 C) can be exploited by using conventional silica gel-water adsorption chiller. The advanced silica gel-water adsorption chiller can operate effectively by utilizing low-grade waste heat ({approximately}50 C) as the driving source with a cooling source of 30 C. In this paper, the effect of operating temperatures on cycle performance is discussed from the thermodynamic viewpoint. The temperature effectiveness and the entropy generation number on cycle time are analyzed. For a comparatively short cycle time, adsorber/desorber heat exchanger temperature effectiveness reaches up to 92% after only 200 sec. The entropy generation number N{sub s} is defined by the ratio between irreversibility generated during a cycle and availability of the heat transfer fluid. The result showed that for the advanced adsorption cycle the entropy generation number N{sub s} is smaller for hot water temperature between 45 to 55 C with a cooling source of 30 C, while for the conventional cycle N{sub s} is smaller for hot water temperature between 65 to 75 C /with the same cooling source temperature.

Saha, B.B.; Akisawa, Atsushi; Kashiwagi, Takao [Tokyo Univ. of Agriculture and Technology, Koganei, Tokyo (Japan)

1997-12-31T23:59:59.000Z

405

Triple-effect absorption chiller cycle: A step beyond double-effect cycles  

SciTech Connect (OSTI)

Many advanced'' absorption cycles have been proposed during the current century. Of the hundreds of absorption cycles which have been patented throughout the world, all commercially manufactured products for air conditioning buildings have been variations of just two basic absorption cycles: single-effect and condenser-coupled double-effect cycles. The relatively low cooling coefficients of performance (COPs) inherent in single-effect and double-effect cycles limits the economic applicability of absorption air conditioners (chillers) in the United States. A triple-effect absorption chiller cycle is discussed. This cycle uses two condensers and two absorbers to achieve the triple effect.'' Depending on the absorption fluids selected, this triple-effect cycle is predicted to improve cooling COPs by 18% to 60% compared with the equivalent double-effect cycle. This performance improvement is obtained without increasing the total amount of heat-transfer surface area needed for the heat exchangers. A comparison between the calculated performances of a double-effect cycle and a triple-effect cycle (both using ammonia-water (NH{sub 3}/H{sub 2}O) as the absorption fluid pair) is presented. The triple-effect cycle is predicted to have an 18% higher cooling COP (1.41 compared with 1.2 for a double-effect), lower pressure (47.70 atm (701 psi) instead of 68.05 atm (1000 psi)), significantly reduced pumping power (less than one-half that of the double-effect cycle), and potentially lower construction cost (33% less total heat exchange needed). Practical implications for this triple-effect cycle are discussed. 16 refs., 5 figs., 1 tab.

DeVault, R.C.

1990-01-01T23:59:59.000Z

406

Life-cycle analysis of shale gas and natural gas.  

SciTech Connect (OSTI)

The technologies and practices that have enabled the recent boom in shale gas production have also brought attention to the environmental impacts of its use. Using the current state of knowledge of the recovery, processing, and distribution of shale gas and conventional natural gas, we have estimated up-to-date, life-cycle greenhouse gas emissions. In addition, we have developed distribution functions for key parameters in each pathway to examine uncertainty and identify data gaps - such as methane emissions from shale gas well completions and conventional natural gas liquid unloadings - that need to be addressed further. Our base case results show that shale gas life-cycle emissions are 6% lower than those of conventional natural gas. However, the range in values for shale and conventional gas overlap, so there is a statistical uncertainty regarding whether shale gas emissions are indeed lower than conventional gas emissions. This life-cycle analysis provides insight into the critical stages in the natural gas industry where emissions occur and where opportunities exist to reduce the greenhouse gas footprint of natural gas.

Clark, C.E.; Han, J.; Burnham, A.; Dunn, J.B.; Wang, M. (Energy Systems); ( EVS)

2012-01-27T23:59:59.000Z

407

EVOLVING LEG CYCLES TO PRODUCE HEXAPOD GAITS GARY B. PARKER  

E-Print Network [OSTI]

movement by the servos. The best means of combining these leg cycles into a gait cycle is learnedEVOLVING LEG CYCLES TO PRODUCE HEXAPOD GAITS GARY B. PARKER Computer Science, Connecticut College by dividing the prob- lem into two parts: leg cycle learning and gait cycle learning. Servo pulses required

Parker, Gary B.

408

The endomorphism near ring on the quaternion group  

E-Print Network [OSTI]

'IHE FNDOMORPHISM NEAR RING ON THE QUATERNION CROUP A Thesis by Mary Katherine King Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE Au~us t (Month...) (Year) Major Subject: Mathematics TNE ENDOMO1PNTSM NEAR RlNG ON T11E QUATEPBTON GROUP A Thesis by Mary Katherine King Approved as to style and content by: ha man of Committee (Member) (Member) (Memb er) (Memb r) (Member) ~Au, ust 1969 (Month...

King, Mary Katherine

1969-01-01T23:59:59.000Z

409

Transverse instability of the antiproton beam in the Recycler Ring  

SciTech Connect (OSTI)

The brightness of the antiproton beam in Fermilab's 8 GeV Recycler ring is limited by a transverse instability. This instability has occurred during the extraction process to the Tevatron for large stacks of antiprotons even with dampers in operation. This paper describes observed features of the instability, introduces the threshold phase density to characterize the beam stability, and finds the results to be in agreement with a resistive wall instability model. Effective exclusion of the longitudinal tails from Landau damping by decreasing the depth of the RF potential well is observed to lower the threshold density by up to a factor of two.

Prost, L.R.; Bhat, C.M.; Burov, A.; Crisp, J.; Eddy, N.; Hu, M.; Shemyakin, A.; /Fermilab

2011-03-01T23:59:59.000Z

410

Reliability analysis for LEB ring magnet power system in SSC  

SciTech Connect (OSTI)

The LEB ring magnet power system contains six subsystems, supervisory control, power supplies, regulation, DC bus, resonant cells, and fault sensing network. The system availability of the total LEB RMPS is required to be 0.999. The work in this paper is to allocate the overall LEB RMPS reliability requirement into reliability requirements for each of the subsystems and lower-tier items. The Feasibility-of-Objective technique combining with engineering experience is the key for the allocation. MIL-HDBK-217F is used to derate SCR components. 7 refs., 5 figs.

Smedley, K.

1991-11-01T23:59:59.000Z

411

Optical distortions in electron/positron storage rings  

SciTech Connect (OSTI)

We have studied the optical distortions in the PEP electron/positron storage ring for various optical configurations using the computer programs DIMAT, HARMON, PATRICIA, and TURTLE. The results are shown graphically by tracing several thousand trajectories from one interaction region to the next using TURTLE and by tracing a few selected rays several hundred turns using the programs DIMAT and PATRICIA. The results show an interesting correlation between the calculated optical cleanliness of a particular lattice configuration and the observed operating characteristics of the machine.

Brown, K.L.; Donald, M.; Servranckx, R.

1983-01-01T23:59:59.000Z

412

NREL: Energy Analysis: Life Cycle Assessment Harmonization  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Life Cycle Assessment Harmonization Life Cycle Assessment Harmonization Life cycle assessment (LCA) harmonization helps lenders, utility executives, and lawmakers get the best, most precise information on greenhouse gas emissions from various sources of energy. LCA has been used to estimate and compare GHG emissions from utility-scale power systems for three decades, often with considerable variability in results. Harmonization provides more exact estimates of greenhouse-gas emissions for renewable and conventional electricity generation technologies, clarifying inconsistent and conflicting estimates in the published literature and reducing uncertainty. Highlights of Recent Studies Chart that compares published and harmonized lifecycle greenhouse gas emissions. For help reading this chart, please contact the webmaster.

413

Heat resources and organic Rankine cycle machines  

Science Journals Connector (OSTI)

Abstract Various Rankine cycle architectures for single fluids and other improved versions operating with ammonia/water mixture are presented in this paper. Untapped heat resources and their potential for driving organic Rankine cycles are outlined. The nature state and temperature of the heat source significantly influences the choice of the type of organic Rankine cycle machine. The temperature appears as a critical parameter during the selection process. Modules differ from one another from technology, size and cost viewpoints. The investment cost of an ORC project includes machine, engineering, system integration, capital costs, etc. and is closely linked to the application.

Bertrand F. Tchanche; M. Ptrissans; G. Papadakis

2014-01-01T23:59:59.000Z

414

Edge usage, motifs, and regulatory logic for cell cycling genetic networks  

Science Journals Connector (OSTI)

The cell cycle is a tightly controlled process, yet it shows marked differences across species. Which of its structural features follow solely from the ability to control gene expression? We tackle this question in silico by examining the ensemble of all regulatory networks which satisfy the constraint of producing a given sequence of gene expressions. We focus on three cell cycle profiles coming from baker's yeast, fission yeast, and mammals. First, we show that the networks in each of the ensembles use just a few interactions that are repeatedly reused as building blocks. Second, we find an enrichment in network motifs that is similar in the two yeast cell cycle systems investigated. These motifs do not have autonomous functions, yet they reveal a regulatory logic for cell cycling based on a feed-forward cascade of activating interactions.

M. Zagorski; A. Krzywicki; O. C. Martin

2013-01-30T23:59:59.000Z

415

thermonuclear functions  

E-Print Network [OSTI]

Two representations of the extended gamma functions ? 2,0 0,2 [(b,x)] are proved. These representations are exploited to find a transformation relation between two Foxs H-functions. These results are used to solve Foxs H-function in terms of Meijers G-function for certain values of the parameters. A closed form representation of the kernel of the Bessel type integral transform is also proved. 1.

M. Aslam Chaudhry

1999-01-01T23:59:59.000Z

416

Energy Down Conversion between Classical Electromagnetic Fields via a Quantum Mechanical SQUID Ring  

E-Print Network [OSTI]

We consider the interaction of a quantum mechanical SQUID ring with a classical resonator (a parallel $LC$ tank circuit). In our model we assume that the evolution of the ring maintains its quantum mechanical nature, even though the circuit to which it is coupled is treated classically. We show that when the SQUID ring is driven by a classical monochromatic microwave source, energy can be transferred between this input and the tank circuit, even when the frequency ratio between them is very large. Essentially, these calculations deal with the coupling between a single macroscopic quantum object (the SQUID ring) and a classical circuit measurement device where due account is taken of the non-perturbative behaviour of the ring and the concomitant non-linear interaction of the ring with this device.

M. J. Everitt; T. D. Clark; P. B. Stiffell; C. J. Harland; J. F. Ralph

2005-05-16T23:59:59.000Z

417

NA Standards | Valence Geometries | Bond Angles-Furanose Rings  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

angles in Furanose Rings angles in Furanose Rings ----------------------------------------------------- ribose deoxyribose ----------------------------------------------------- angle mean esd N mean esd N value value ----------------------------------------------------- C1'-C2'-C3' 101.5 (0.9, 80) 102.7 (1.4, 47) C2'-C3'-C4' 102.7 (1.0, 80) 103.2 (1.0, 47) C3'-C4'-O4' 105.5 (1.4, 80) 105.6 (1.0, 47) C4'-O4'-C1' 109.6 (0.9, 80) 109.7 (1.4, 47) O4'-C1'-C2' 106.4 (1.4, 80) 106.1 (1.0, 47) C1'-C2'-O2' 110.6 (3.0, 80) na C3'-C2'-O2' 113.3 (2.9, 80) na C2'-C3'-O3' 111.0 (2.8, 80) 110.6 (2.7, 47) C4'-C3'-O3' 110.6 (2.6, 80) 110.3 (2.2, 47) C5'-C4'-C3' 115.5 (1.5, 80) 114.7 (1.5, 47)

418

SUPERCONDUCTING RING CYCLOTRON FOR RIKEN RI BEAM FACTORY IN JAPAN  

SciTech Connect (OSTI)

Since 1997, RIKEN Nishina Center has been constructing the Radioactive Isotope Beam Factory (RIBF) and succeeded in beam commissioning of its accelerator complex at the end of 2006. The world's first superconducting ring cyclotron (SRC) is the final booster in the RIBF accelerator complex which is able to accelerate all-element heavy ions to a speed of about 70% of the velocity of light. The ring cyclotron consists of 6 major superconducting sector magnets with a maximum field of 3.8 T. The total stored energy is 235 MJ, and its overall sizes are 19 m diameter, 8 m height and 8,300 tons. The magnet system assembly was completed in August 2005, and successfully reached the maximum field in November 2005. The first beam was extracted at the end of 2006 and the first uranium beam was extracted in March 2007. However operation of the helium refrigerator was not satisfactory although the commissioning of SRC was successful. Operation was stopped every two month due to degradation of its cooling power. In February 2008 the reason of the degradation was revealed to be oil contamination. Operation of the cryogenic system was restarted from August 2008 after hard task to clean up the helium refrigerator and to add oil separators to the compressor. After restoration long-term steady operation to keep the magnet superconducting continued for about 8 months with no sign of degradation of cooling capacity.

Okuno, H.; Dantsuka, T.; Yamada, K.; Kase, M.; Maie, T.; Kamigaito, O. [RIKEN Nishina Center, Wako, Saitama, 351-0198 (Japan)

2010-04-09T23:59:59.000Z

419

Weibull Effective Area for Hertzian Ring Crack Initiation Stress  

SciTech Connect (OSTI)

Spherical or Hertzian indentation is used to characterize and guide the development of engineered ceramics under consideration for diverse applications involving contact, wear, rolling fatigue, and impact. Ring crack initiation can be one important damage mechanism of Hertzian indentation. It is caused by sufficiently-high, surface-located, radial tensile stresses in an annular ring located adjacent to and outside of the Hertzian contact circle. While the maximum radial tensile stress is known to be dependent on the elastic properties of the sphere and target, the diameter of the sphere, the applied compressive force, and the coefficient of friction, the Weibull effective area too will be affected by those parameters. However, the estimations of a maximum radial tensile stress and Weibull effective area are difficult to obtain because the coefficient of friction during Hertzian indentation is complex, likely intractable, and not known a priori. Circumventing this, the Weibull effective area expressions are derived here for the two extremes that bracket all coefficients of friction; namely, (1) the classical, frictionless, Hertzian case where only complete slip occurs, and (2) the case where no slip occurs or where the coefficient of friction is infinite.

Jadaan, Osama M. [University of Wisconsin, Platteville; Wereszczak, Andrew A [ORNL; Johanns, Kurt E [ORNL

2011-01-01T23:59:59.000Z

420

Operational advances in ring current modeling using RAM-SCB  

SciTech Connect (OSTI)

The Ring current Atmosphere interaction Model with Self-Consistently calculated 3D Magnetic field (RAM-SCB) combines a kinetic model of the ring current with a force-balanced model of the magnetospheric magnetic field to create an inner magnetospheric model that is magnetically self consistent. RAM-SCB produces a wealth of outputs that are valuable to space weather applications. For example, the anisotropic particle distribution of the KeV-energy population calculated by the code is key for predicting surface charging on spacecraft. Furthermore, radiation belt codes stand to benefit substantially from RAM-SCB calculated magnetic field values and plasma wave growth rates - both important for determining the evolution of relativistic electron populations. RAM-SCB is undergoing development to bring these benefits to the space weather community. Data-model validation efforts are underway to assess the performance of the system. 'Virtual Satellite' capability has been added to yield satellite-specific particle distribution and magnetic field output. The code's outer boundary is being expanded to 10 Earth Radii to encompass previously neglected geosynchronous orbits and allow the code to be driven completely by either empirical or first-principles based inputs. These advances are culminating towards a new, real-time version of the code, rtRAM-SCB, that can monitor the inner magnetosphere conditions on both a global and spacecraft-specific level. This paper summarizes these new features as well as the benefits they provide the space weather community.

Welling, Daniel T [Los Alamos National Laboratory; Jordanova, Vania K [Los Alamos National Laboratory; Zaharia, Sorin G [Los Alamos National Laboratory; Morley, Steven K [Los Alamos National Laboratory

2010-12-03T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Nuclear Fuel Cycle | Department of Energy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Fuel Cycle Fuel Cycle Nuclear Fuel Cycle GC-52 provides legal advice to DOE regarding research and development of nuclear fuel and waste management technologies that meet the nation's energy supply, environmental, and energy security needs. GC-52 also advises DOE on issues involving support for international fuel cycle initiatives aimed at advancing a common vision of the necessity of the expansion of nuclear energy for peaceful purposes worldwide in a safe and secure manner. In addition, GC-52 provides legal advice to DOE regarding the management and disposition of excess uranium in DOE's uranium stockpile. GC-52 attorneys participate in meetings of DOE's Uranium Inventory Management Coordinating Committee and provide advice on compliance with statutory requirements for the sale or transfer of uranium.

422

Life Cycle Inventory Database | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Commercial Buildings » Research Projects » Life Cycle Inventory Commercial Buildings » Research Projects » Life Cycle Inventory Database Life Cycle Inventory Database The U.S. Life Cycle Inventory (LCI) Database serves as a central repository for information about the total energy and resource impacts of developing and using various commercial building materials, components, and assemblies. The database helps manufacturers, building designers, and developers select energy-efficient and environmentally friendly materials, products, and processes for their projects based on the environmental impact of an item over its entire lifespan. The U.S. Department of Energy and the National Renewable Energy Laboratory (NREL) developed the database in 2003 with input from a variety of partners. NREL maintains and updates the database with support from the

423

Obligations Notification Cycle and New Obligations Presentation  

National Nuclear Security Administration (NNSA)

Obligations Notification Cycle and Obligations Notification Cycle and Obligations Notification Cycle and Obligations Notification Cycle and New Obligations New Obligations Bill Benton, DOE/SO-62 Pat Tana, NRC/NSIR Michelle Romano, NAC/NMMSS Obligations Accounting Implementation Workshop Obligations Accounting Implementation Workshop January 13, 2004 January 13, 2004 Crowne Crowne Plaza Plaza Ravinia Ravinia Atlanta, Georgia Atlanta, Georgia Notifications Notifications * There are issues! - Timeliness - Information (or lack thereof) - Other? * DOE Facilities - Bill Benton, 301-903-1150, Bill.Benton@hq.doe.gov * NRC Facilities - Pat Tana, 301-415-8105, pmt@nrc.gov * DOE/SO-62, NRC to request meeting of Government representatives involved. * DOE/SO-62, NRC to solicit concrete case studies to

424

Life Cycle Assessment of a Wind Farm  

Science Journals Connector (OSTI)

In the next step of the LCA, specific energy expenditures and produced emissions were linked to the inventory analysis result. The database of the Swiss Center for Life Cycle Inventories Ecoinvent lists over 4,00...

Hermann-Josef Wagner; Jyotirmay Mathur

2013-01-01T23:59:59.000Z

425

Development Cycle Time Simulation For Civil Aircraft  

Science Journals Connector (OSTI)

Cycle Time Reduction (CTR) will be one of the major factors affecting the future of the civil aerospace industry. This focus is the end reflection of the level of competition in the commercial large carrier aircraft industry. Aircraft manufacturer must ...

Spitz William; Golaszewski Richard; Berardino Frank; Johnson Jesse

2001-01-01T23:59:59.000Z

426

The annual cycles of phytoplankton biomass  

Science Journals Connector (OSTI)

...Forrest The annual cycles of phytoplankton biomass Monika Winder 1 * James E. Cloern 2...Here, we ask whether phytoplankton biomass also fluctuates over a consistent annual...compiled 125 time series of phytoplankton biomass (chlorophyll a concentration) from temperate...

2010-01-01T23:59:59.000Z

427

Cycling Losses During Screw Air Compressor Operation  

E-Print Network [OSTI]

efficiency confirmed that modulation only controls are accurately portrayed by traditional part load models under most conditions. It also confirmed that load-unload type controls are accurately modeled when cycle times are longer than 5 minutes. However...

Maxwell, J. B.; Wheeler, G.; Bushnell, D.

428

Industrial Heat Recovery with Organic Rankine Cycles  

E-Print Network [OSTI]

Rising energy costs are encouraging energy intensive industries to investigate alternative means of waste heat recovery from process streams. The use of organic fluids in Rankine cycles offers improved potential for economical cogeneration from...

Hnat, J. G.; Patten, J. S.; Cutting, J. C.; Bartone, L. M.

1982-01-01T23:59:59.000Z

429

Cycle time reduction through wafer starts control  

E-Print Network [OSTI]

Intel's Fab 17, located in Hudson, Massachusetts, has experienced dramatic improvements in its cycle time performance in the last two years. These improvements have been attributed to lean implementation efforts, reduced ...

Wang, Sam, M.B.A. Massachusetts Institute of Technology

2008-01-01T23:59:59.000Z

430

Techno-Economics & Life Cycle Assessment (Presentation)  

SciTech Connect (OSTI)

This presentation provides an overview of the techno-economic analysis (TEA) and life cycle assessment (LCA) capabilities at the National Renewable Energy Laboratory (NREL) and describes the value of working with NREL on TEA and LCA.

Dutta, A.; Davis, R.

2011-12-01T23:59:59.000Z

431

Project Profile: Brayton Cycle Baseload Power Tower  

Broader source: Energy.gov [DOE]

Wilson Solarpower, under the Baseload CSP FOA, is validating a proposed utility-scale, Brayton cycle baseload power tower system with a capacity factor of at least 75% and LCOE of $0.09/kWh.

432

Life Cycle Cost Analysis for Sustainable Buildings  

Broader source: Energy.gov [DOE]

To help facility managers make sound decisions, FEMP provides guidance and resources on applying life cycle cost analysis (LCCA) to evaluate the cost-effectiveness of energy and water efficiency investments.

433

life cycle inventory | OpenEI  

Open Energy Info (EERE)

life cycle inventory life cycle inventory Dataset Summary Description Datasets are for the US electricity grid system for eGrid regions (AKGD, AKMS, AZNM, CAMX, ERCT, FRCC, HIMS, HIOA, MROE, MROW, NEWE, NWPP, NYCW, NYLI, NYUP, RFCE, RFCM, RFCW, RMPA, SPNO, SPSO, SRMV, SRMW, SRSO, SRTV, SRVC) for 2008. The data is provided in life cycle inventory forms (xls and xml) . A module report and a detailed spreadsheet are also included.Datasets include generation and transmission of electricity for each of the eGrid regions. It is representative of the year 2008 mix of fuels used for utility generations for each of the eGrid regions Source USLCI Database Date Released Unknown Date Updated Unknown Keywords eGrid Electricity grid LCI life cycle inventory US Data application/zip icon egrid_electricity_lci_datasets_2008.zip (zip, 7 MiB)

434

Life-Cycle Analysis of Geothermal Technologies  

Broader source: Energy.gov [DOE]

The results and tools from this project will help GTP and stakeholders determine and communicate GT energy and GHG benefits and water impacts. The life-cycle analysis (LCA) approach is taken to address these effects.

435

Relative cycles and Chow sheaves. Andrei Suslin, Vladimir Voevodsky  

E-Print Network [OSTI]

. . . . . . . . . . . . . . . . . 73 1 Introduction. Let X be a scheme. A cycle on X is a formal linear combination of points Relative cycles and Chow sheaves. Andrei Suslin, Vladimir Voevodsky equidimensional closed subschemes. . . . . . . . . 9 2.3 Cycles on Noetherian schemes

436

Global Carbon Cycle, Carbon Dioxide Emissions and Mitigation  

Science Journals Connector (OSTI)

The carbon cycle is one of the biogeochemical cycles and describes the movement of carbon, in its many forms, within the biosphere, atmosphere, oceans and geosphere. The global carbon cycle involves the earth...

2008-01-01T23:59:59.000Z

437

6D mu (+/-) cooling using a solenoid-dipole ring cooler for a muon collider  

SciTech Connect (OSTI)

Six dimensional cooling of large emittance {mu}{sup +} and {mu}{sup -} beams is required in order to obtain the desired luminosity for a muon collider. We propose to use a ring cooler that employs both dipoles and solenoids with the additional requirement that the arcs of the ring be achromatic. We describe the lattice and the beam dynamics of the proposed ring, and demonstrate that the lattice gives substantial cooling in all 6 phase space dimensions.

Garren, A.; Berg, J.; Cline, D.; Ding, X.; Kirk, H.G.

2011-08-01T23:59:59.000Z

438

First law of black ring thermodynamics in higher dimensional Chern-Simons gravity  

Science Journals Connector (OSTI)

The physical process version and the equilibrium state version of the first law of black ring thermodynamics in n-dimensional Einstein gravity with Chern-Simons term were derived. This theory constitutes the simplest generalization of the five-dimensional one admitting a stationary black ring solution. The equilibrium state version of the first law of black ring mechanics was achieved by choosing any cross section of the event horizon to the future of the bifurcation surface.

Marek Rogatko

2007-01-05T23:59:59.000Z

439

Black rings and the physical process version of the first law of thermodynamics  

Science Journals Connector (OSTI)

We consider the problem of the physical process version of the first law of black ring thermodynamics in n-dimensional Einstein gravity with additional (p+1)-form field strength and dilaton fields. The first order variations of mass, angular momentum and local charge for black ring are derived. From them we prove the physical process version of the first law of thermodynamic for stationary black rings.

Marek Rogatko

2005-10-10T23:59:59.000Z

440

First law of black ring thermodynamics in higher dimensional Chern-Simons gravity  

SciTech Connect (OSTI)

The physical process version and the equilibrium state version of the first law of black ring thermodynamics in n-dimensional Einstein gravity with Chern-Simons term were derived. This theory constitutes the simplest generalization of the five-dimensional one admitting a stationary black ring solution. The equilibrium state version of the first law of black ring mechanics was achieved by choosing any cross section of the event horizon to the future of the bifurcation surface.

Rogatko, Marek [Institute of Physics, Maria Curie-Sklodowska University, 20-031 Lublin, pl. Marii Curie-Sklodowskiej 1 (Poland)

2007-01-15T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Black rings and the physical process version of the first law of thermodynamics  

SciTech Connect (OSTI)

We consider the problem of the physical process version of the first law of black ring thermodynamics in n-dimensional Einstein gravity with additional (p+1)-form field strength and dilaton fields. The first order variations of mass, angular momentum and local charge for black ring are derived. From them we prove the physical process version of the first law of thermodynamic for stationary black rings.

Rogatko, Marek [Institute of Physics, Maria Curie-Sklodowska University, 20-031 Lublin, pl. Marii Curie-Sklodowskiej 1 (Poland)

2005-10-01T23:59:59.000Z

442

Carbon Capture (Carbon Cycle 2.0)  

ScienceCinema (OSTI)

Berend Smit speaks at the Carbon Cycle 2.0 kick-off symposium Feb. 3, 2010. We emit more carbon into the atmosphere than natural processes are able to remove - an imbalance with negative consequences. Carbon Cycle 2.0 is a Berkeley Lab initiative to provide the science needed to restore this balance by integrating the Labs diverse research activities and delivering creative solutions toward a carbon-neutral energy future. http://carboncycle2.lbl.gov/

Smit, Berend

2011-06-08T23:59:59.000Z

443

Cooperative regulation in yeast cell cycle network  

E-Print Network [OSTI]

We define a measure of cooperativity for gene regulatory networks which we propose should be maximized under a demand for energy efficiency. We investigate its dependence on network size, connectivity and the fraction of repressory/activatory interactions. Next, we consider the cell-cycle regulatory network of the yeast, Saccharomyces cerevisiae, as a case study and calculate its degree of cooperativity. A comparison with random networks of similar size and composition reveals that the yeast's cell-cycle regulation is exceptionally cooperative.

Nese Aral; Alkan Kabakcioglu

2014-06-28T23:59:59.000Z

444

Predicting solar cycle 24 with a solar dynamo model  

E-Print Network [OSTI]

Whether the upcoming cycle 24 of solar activity will be strong or not is being hotly debated. The solar cycle is produced by a complex dynamo mechanism. We model the last few solar cycles by `feeding' observational data of the Sun's polar magnetic field into our solar dynamo model. Our results fit the observed sunspot numbers of cycles 21-23 extremely well and predict that cycle~24 will be about 35% weaker than cycle~23.

Arnab Rai Choudhuri; Piyali Chatterjee; Jie Jiang

2007-01-18T23:59:59.000Z

445

Enhancement of combined cycle performance using transpiration cooling of gas turbine blades with steam  

Science Journals Connector (OSTI)

Gas/steam combined cycle is synergetic combination of Brayton cycle based topping cycle and Rankine cycle based bottoming cycle, which have capability of operating independently too. Combined cycle performance de...

Sanjay Kumar; Onkar Singh

2014-06-01T23:59:59.000Z

446

FODO-Supercell Based Compact Ring Design with Tunable Momentum Compaction and Optimized Dynamic Aperture  

SciTech Connect (OSTI)

A storage ring with tunable momentum compaction has the advantage in achieving different RMS bunch length with similar RF capacity, which is potentially useful for many applications, such as linear collider damping ring and pre-damping ring where injected beam has a large energy spread and a large transverse emittance. A tunable bunch length also makes the commissioning and fine tuning easier in manipulating the single bunch instabilities. In this paper, a compact ring design based on a supercell is presented, which achieves a tunable momentum compaction while maintaining a large dynamic aperture.

Sun, Yipeng; /SLAC

2012-05-11T23:59:59.000Z

447

Effects of Modularity and Connectivity on OADM Deployment in Ring Networks  

Science Journals Connector (OSTI)

For a class of Optical Add/Drop Multiplexers, we empirically study the effects of port modularity and connectivity on device deployment in ring networks. Designs with greater...

Nuzman, Carl; Kumaran, Krishnan; Nithi, Nachi; Saniee, Iraj; Levy, David; Mitev, Peter

448

Wafer-level packaging with compression-controlled seal ring bonding  

DOE Patents [OSTI]

A device may be provided in a sealed package by aligning a seal ring provided on a first surface of a first semiconductor wafer in opposing relationship with a seal ring that is provided on a second surface of a second semiconductor wafer and surrounds a portion of the second wafer that contains the device. Forcible movement of the first and second wafer surfaces toward one another compresses the first and second seal rings against one another. A physical barrier against the movement, other than the first and second seal rings, is provided between the first and second wafer surfaces.

Farino, Anthony J

2013-11-05T23:59:59.000Z

449

Self-mixing interference in fiber ring laser and its application for vibration measurement  

Science Journals Connector (OSTI)

A new approach for self-mixing interference in fiber ring laser and its application to vibration measurement is presented. Fourier transform method is proposed to improve the...

Dai, Xiajuan; Wang, Ming; Zhao, Yi; Zhou, Junping

2009-01-01T23:59:59.000Z

450

Gas-flow-induced controlled unidirectional operation of a CO2 ring laser  

Science Journals Connector (OSTI)

It is shown experimentally and theoretically that axial gas flow leads to controlled unidirectional operation of a CO2 ring laser. The direction of emission, clockwise or...

Boulnois, J L; Agrawal, Govind P; Bret, G; Cottin, P; Van Lerberghe, A

1985-01-01T23:59:59.000Z

451

A priori information in a regularized sinogram-based method for removing ring artefacts in tomography  

Science Journals Connector (OSTI)

A ring artefact suppression method based on ideas of the theory of inverse problems is proposed for the case of parallel-beam geometry.

Titarenko, S.

2010-05-14T23:59:59.000Z

452

Electron cloud instabilities in the Proton Storage Ring and Spallation Neutron Source  

Science Journals Connector (OSTI)

Electron cloud instabilities in the Los Alamos Proton Storage Ring and those foreseen for the Oak Ridge Spallation Neutron Source are examined theoretically, numerically, and experimentally.

M. Blaskiewicz; M. A. Furman; M. Pivi; R. J. Macek

2003-01-21T23:59:59.000Z

453

Federal Energy Management Program: Life Cycle Cost Analysis for Sustainable  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Life Cycle Cost Life Cycle Cost Analysis for Sustainable Buildings to someone by E-mail Share Federal Energy Management Program: Life Cycle Cost Analysis for Sustainable Buildings on Facebook Tweet about Federal Energy Management Program: Life Cycle Cost Analysis for Sustainable Buildings on Twitter Bookmark Federal Energy Management Program: Life Cycle Cost Analysis for Sustainable Buildings on Google Bookmark Federal Energy Management Program: Life Cycle Cost Analysis for Sustainable Buildings on Delicious Rank Federal Energy Management Program: Life Cycle Cost Analysis for Sustainable Buildings on Digg Find More places to share Federal Energy Management Program: Life Cycle Cost Analysis for Sustainable Buildings on AddThis.com... Sustainable Buildings & Campuses Basics

454

NREL: U.S. Life Cycle Inventory Database - Related Links  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Related Links Related Links Below are links to life cycle inventory (LCI) databases, life cycle assessment (LCA) information, LCA tools, research institutes utilizing LCA, labeling initiatives and organizations, international LCA initiatives, LCA online forums. Life Cycle Inventory Data Ecoinvent: Swiss Centre for Life Cycle Inventories IVAM LCA Data 4: Dutch LCA Database KITECH (Korea Institute of Industrial Technology): Korea National Cleaner Production Center LCI Database Life Cycle Assessment Information IERE (The Institute for Environmental Research and Education): The American Center for Life Cycle Assessment SETAC (Society of Environmental Toxicology and Chemistry): SETAC Life Cycle Assessment SPOLD (Society for Promotion of Life-cycle Assessment Development): 2.0 LCA Consultants homepage

455

NETL - Petroleum-Based Fuels Life Cycle Greenhouse Gas Analysis...  

Open Energy Info (EERE)

- Petroleum-Based Fuels Life Cycle Greenhouse Gas Analysis 2005 Baseline Model Jump to: navigation, search Tool Summary LAUNCH TOOL Name: NETL - Petroleum-Based Fuels Life Cycle...

456

Life Cycle Cost Analysis for Sustainable Buildings | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Sustainable Buildings & Campuses Life Cycle Cost Analysis for Sustainable Buildings Life Cycle Cost Analysis for Sustainable Buildings To help facility managers make sound...

457

Lessons Learned: Devolping Thermochemical Cycles for Solar Heat...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Lessons Learned: Devolping Thermochemical Cycles for Solar Heat Storage Applications Lessons Learned: Devolping Thermochemical Cycles for Solar Heat Storage Applications This...

458

Economizer refrigeration cycle space heating and cooling system and process  

DOE Patents [OSTI]

This invention relates to heating and cooling systems and more particularly to an improved system utilizing a Stirling Cycle engine heat pump in a refrigeration cycle. 18 figs.

Jardine, D.M.

1983-03-22T23:59:59.000Z

459

Economizer refrigeration cycle space heating and cooling system and process  

DOE Patents [OSTI]

This invention relates to heating and cooling systems and more particularly to an improved system utilizing a Stirling Cycle engine heat pump in a refrigeration cycle.

Jardine, Douglas M. (Colorado Springs, CO)

1983-01-01T23:59:59.000Z

460

Department of Energy Awards $15 Million for Nuclear Fuel Cycle...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Million for Nuclear Fuel Cycle Technology Research and Development Department of Energy Awards 15 Million for Nuclear Fuel Cycle Technology Research and Development August 1,...

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Biotic and abiotic pathways of phosphorus cycling in minerals...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and abiotic pathways of phosphorus cycling in minerals and sediments: insights from oxygen isotopes in phosphate. Biotic and abiotic pathways of phosphorus cycling in minerals...

462

Full Fuel-Cycle Comparison of Forklift Propulsion Systems | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Full Fuel-Cycle Comparison of Forklift Propulsion Systems Full Fuel-Cycle Comparison of Forklift Propulsion Systems This report examines forklift propulsion systems and addresses...

463

A Revolutionary Hybrid Thermodynamic Cycle for Bianary Geothermal...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

A Revolutionary Hybrid Thermodynamic Cycle for Bianary Geothermal Power A Revolutionary Hybrid Thermodynamic Cycle for Bianary Geothermal Power A Revolutionary Hybrid Thermodynamic...

464

Betatron-Function Measurement in Lattices with 90-Degrees Sections  

SciTech Connect (OSTI)

Lattice functions derived from betatron phase-advance measurements have been used successfully at many e{sup +}-e{sup -} facilities in the world, including at the PEP-II High Energy Ring. For the Low energy Ring of PEP-II, however, extraction of meaningful beta functions is hampered by the 90{sup o} phase advance/cell in the arcs, which causes a singularity in the expressions for beta. An algorithm has been developed calculating beta functions based on {beta} and {alpha} at the beginning of an arc and tracking the Twiss parameters through the arc while matching the observed phase advance/cell. Stability of the algorithm is improved by doing the same calculation 'backward' as well as forward and averaging the result. The algorithm allows estimating beta functions at bad BPMs in many cases. The paper presents the algorithm used as well as examples of use in PEP.

Wienands, U.; /SLAC; Biagini, M.E.; /Frascati

2012-04-24T23:59:59.000Z

465

Combined cycle and run performance is maximised when the cycle is completed at the highest sustainable intensity  

Science Journals Connector (OSTI)

The aim of this study was to determine the effect of cycle intensity on subsequent running performance and combined cyclerun (CR) performance. Seven triathletes undertook a cycling graded exercise test to exhaus...

Robert Suriano; David Bishop

2010-11-01T23:59:59.000Z

466

Estimating Fuel Cycle Externalities: Analytical Methods and Issues, Report 2  

SciTech Connect (OSTI)

The activities that produce electric power typically range from extracting and transporting a fuel, to its conversion into electric power, and finally to the disposition of residual by-products. This chain of activities is called a fuel cycle. A fuel cycle has emissions and other effects that result in unintended consequences. When these consequences affect third parties (i.e., those other than the producers and consumers of the fuel-cycle activity) in a way that is not reflected in the price of electricity, they are termed ''hidden'' social costs or externalities. They are the economic value of environmental, health and any other impacts, that the price of electricity does not reflect. How do you estimate the externalities of fuel cycles? Our previous report describes a methodological framework for doing so--called the damage function approach. This approach consists of five steps: (1) characterize the most important fuel cycle activities and their discharges, where importance is based on the expected magnitude of their externalities, (2) estimate the changes in pollutant concentrations or other effects of those activities, by modeling the dispersion and transformation of each pollutant, (3) calculate the impacts on ecosystems, human health, and any other resources of value (such as man-made structures), (4) translate the estimates of impacts into economic terms to estimate damages and benefits, and (5) assess the extent to which these damages and benefits are externalities, not reflected in the price of electricity. Each step requires a different set of equations, models and analysis. Analysts generally believe this to be the best approach for estimating externalities, but it has hardly been used! The reason is that it requires considerable analysis and calculation, and to this point in time, the necessary equations and models have not been assembled. Equally important, the process of identifying and estimating externalities leads to a number of complex issues that also have not been fully addressed. This document contains two types of papers that seek to fill part of this void. Some of the papers describe analytical methods that can be applied to one of the five steps of the damage function approach. The other papers discuss some of the complex issues that arise in trying to estimate externalities. This report, the second in a series of eight reports, is part of a joint study by the U.S. Department of Energy (DOE) and the Commission of the European Communities (EC)* on the externalities of fuel cycles. Most of the papers in this report were originally written as working papers during the initial phases of this study. The papers provide descriptions of the (non-radiological) atmospheric dispersion modeling that the study uses; reviews much of the relevant literature on ecological and health effects, and on the economic valuation of those impacts; contains several papers on some of the more complex and contentious issues in estimating externalities; and describes a method for depicting the quality of scientific information that a study uses. The analytical methods and issues that this report discusses generally pertain to more than one of the fuel cycles, though not necessarily to all of them. The report is divided into six parts, each one focusing on a different subject area.

Barnthouse, L.W.; Cada, G.F.; Cheng, M.-D.; Easterly, C.E.; Kroodsma, R.L.; Lee, R.; Shriner, D.S.; Tolbert, V.R.; Turner, R.S.

1994-07-01T23:59:59.000Z

467

Ignition of Doped Helium Nanodroplets in Intense Few-Cycle Laser Pulses  

Science Journals Connector (OSTI)

The ultra-fast dynamics of He nanodroplets (103105 atoms) in intense (17 1014 W/cm2...), few-cycle (?10 fs), infrared (?790 nm) laser pulses has been investigated as a function ... number of dopant rare-gas at...

S. R. Krishnan; L. Fechner; M. Kremer

2012-01-01T23:59:59.000Z

468

Nitrogen Cycling in United Kingdom Forests: The Relevance of Basic Ecological Research [and Discussion  

Science Journals Connector (OSTI)

...cycling characteristics. The Pinus nigra plantation on Culbin Sands is functioning on a low...contrast, the mixed deciduous Meathop Wood has a much larger capital of N and higher...proportion of added fertilizer N in the biomass and forest floor, and increased growth...

1982-01-01T23:59:59.000Z

469

Advanced Organic Vapor Cycles for Improving Thermal Conversion Efficiency in Renewable Energy Systems  

E-Print Network [OSTI]

DL Chase and PT Kehoe, "GE Combined-Cycle Product Line andand W Stenze, "Combined Cycle Heat Recovery Optimization,"bottoming cycle FOR combined cycle power plants," Applied

Ho, Tony

2012-01-01T23:59:59.000Z

470

FIFTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE  

SciTech Connect (OSTI)

A series of experiments to monitor the aging performance of Viton{sup reg.} GLT O-rings used in the Model 9975 package has been ongoing for six years at the Savannah River National Laboratory. Sixty-seven mock-ups of 9975 Primary Containment Vessels (PCVs) were assembled and heated to temperatures ranging from 200 to 450 F. They were leak-tested initially and have been tested at nominal six month intervals to determine if they meet the criterion of leaktightness defined in ANSI standard N14.5-97. Fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 F. High temperature aging continues for 36 GLT O-ring fixtures at 200--350 F. Room temperature leak test failures have been experienced in 5 of the GLT O-ring fixtures aging at 300 and 350 F, and in all 3 of the GLT O-ring fixtures aging at higher temperatures. No failures have yet been observed in GLT O-ring fixtures aging at 200 F for 30--48 months, which is still bounding to O-ring temperatures during storage in KAMS. High temperature aging continues for 6 GLT-S O-ring fixtures at 200--300 F. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 F. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 or 300 F for 19 months. For O-ring fixtures that have failed the room temperature leak test and been disassembled, the O-rings displayed a compression set ranging from 51--95%. This is significantly greater than seen to date for packages inspected during KAMS field surveillance (23% average). For GLT O-rings, service life based on the room temperature leak rate criterion is comparable to that predicted by compression stress relaxation (CSR) data at higher temperatures (350--400 F). While there are no comparable failure data yet at aging temperatures below 300 F, extrapolations of the data for GLT O-rings suggests that CSR model predictions provide a conservative prediction of service life relative to the leak rate criterion. Failure data at lower temperatures is needed to verify this apparent trend. Insufficient failure data exist currently to perform a similar comparison for GLT-S O-rings. Aging and periodic leak testing will continue for the remaining fixtures.

Daugherty, W.; Hoffman, E.

2010-11-01T23:59:59.000Z

471

All Ring Tech Co Ltd | Open Energy Information  

Open Energy Info (EERE)

Co Ltd Co Ltd Jump to: navigation, search Name All Ring Tech Co Ltd Place Kaohsiung, Taiwan Product Engaged in the manufacture and sale of semiconductor equipment, passive element equipment, thin film transistor liquid crystal display (TFT-LCD) equipment, optoelectronic products and venturing into thin-film PV manufacturing equipment. Coordinates 22.672569°, 120.293228° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":22.672569,"lon":120.293228,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

472

Dynamical 3-Space: Alternative Explanation of the `Dark Matter Ring'  

E-Print Network [OSTI]

NASA has claimed the discovery of a `Ring of Dark Matter' in the galaxy cluster CL 0024+17, see Jee M.J. et al. arXiv:0705.2171, based upon gravitational lensing data. Here we show that the lensing can be given an alternative explanation that does not involve `dark matter'. This explanation comes from the new dynamics of 3-space. This dynamics involves two constant G and alpha - the fine structure constant. This dynamics has explained the bore hole anomaly, spiral galaxy flat rotation speeds, the masses of black holes in spherical galaxies, gravitational light bending and lensing, all without invoking `dark matter', and also the supernova redshift data without the need for `dark energy'.

Reginald T Cahill

2007-05-20T23:59:59.000Z

473

A ring imaging Cherenkov detector for CLAS12  

SciTech Connect (OSTI)

The energy increase of Jefferson Lab's Continuous Electron Beam Accelerator Facility (CEBAF) to 12 GeV promises to greatly extend the physics reach of its experiments. This will include an upgrade of the CEBAF Large Acceptance Spectrometer (CLAS) to CLAS12, offering unique possibilities to study internal nucleon dynamics. For this excellent hadron identification over the full kinematical range of 38 GeV/c is essential. This will be achieved by the installation of a Ring Imaging CHerenkov (RICH) detector. A novel hybrid imaging design incorporating mirrors, aerogel radiators and Hamamatsu H8500 multianode photomultiplier tubes is proposed. Depending on the incident particle track angle, Cherenkov light will either be imaged directly or after two reflections and passes through the aerogel. The detector design is described, along with preliminary results on individual detector components tests and from recent testbeam studies.

Montgomery, Rachel A. [Glasgow University

2013-12-01T23:59:59.000Z

474

Radiative polarization in high-energy storage rings  

SciTech Connect (OSTI)

Electron and positron beams circulating in high-energy storage rings become spontaneously polarized by the emission of synchrotron radiation. The asymptotic degree of polarization that can be attained is strongly affected by so-called depolarizing resonances. Detailed experimental measurements of the polarization were made SPEAR about ten years ago, but due to lack of a suitable theory only a limited theoretical fit to the data has so far been achieved. I present a general formalism for calculating depolarizing resonances, which as been coded into a computer program called SMILE, and use it to fit the SPEAR data. By the use of suitable approximations, I am able to fit both higher order and nonlinear resonances, and thereby to interpret many hitherto unexplained features in the data, and to resolve a puzzle concerning the asymmetry of certain resonance widths seen in the data. 18 refs., 2 figs.

Mane, S.R.

1989-03-01T23:59:59.000Z

475

Interaction between graphene and metamaterials: split rings vs. wire pairs  

SciTech Connect (OSTI)

We have recently shown that graphene is unsuitable to replace metals in the current-carrying elements of metamaterials. At the other hand, experiments have demonstrated that a layer of graphene can modify the optical response of a metal-based metamaterial. Here we study this electromagnetic interaction between metamaterials and graphene. We show that the weak optical response of graphene can be modified dramatically by coupling to the strong resonant fields in metallic structures. A crucial element determining the interaction strength is the orientation of the resonant fields. If the resonant electric field is predominantly parallel to the graphene sheet (e.g., in a complementary split-ring metamaterial), the metamaterials resonance can be strongly damped. If the resonant field is predominantly perpendicular to the graphene sheet (e.g., in a wire-pair metamaterial), no significant interaction exists.

Zou, Yanhong; Tassin, Philippe; Koschny, Thomas; Soukoulis, Costas

2012-05-14T23:59:59.000Z

476

Fusion of symmetric $D$-branes and Verlinde rings  

E-Print Network [OSTI]

We explain how multiplicative bundle gerbes over a compact, connected and simple Lie group $G$ lead to a certain fusion category of equivariant bundle gerbe modules given by pre-quantizable Hamiltonian $LG$-manifolds arising from Alekseev-Malkin-Meinrenken's quasi-Hamiltonian $G$-spaces. The motivation comes from string theory namely, by generalising the notion of $D$-branes in $G$ to allow subsets of $G$ that are the image of a $G$-valued moment map we can define a `fusion of $D$-branes' and a map to the Verlinde ring of the loop group of $G$ which preserves the product structure. The idea is suggested by the theorem of Freed-Hopkins-Teleman. The case where $G$ is not simply connected is studied carefully in terms of equivariant bundle gerbe modules for multiplicative bundle gerbes.

A. L. Carey; Bai-Ling Wang

2005-05-14T23:59:59.000Z

477

Synthesis of Medium Ring Ethers. 5. The Synthesis of (+)-Laurencin  

Science Journals Connector (OSTI)

The eight-membered medium ring ether natural product (+)-laurencin 1 is the prototypical member of a growing family of marine natural product cyclic ethers isolated from red algae and those marine organisms which feed on Laurencia species. ... The reaction mixture immediately became yellow and gradually turned dark red as gas was evolved. ... We thank the Engineering and Physical Sciences Research Council (EPSRC) UK for a research grant, Pfizer Central Research, and Corpus Christi College Cambridge for the award of a studentship and a Junior Research Fellow ship (J.W.B.), the Cambridge European Overseas Trust, Ciba (Novartis) and the Swiss Foundation for Gifted Students (scholarship to S.D.), and the Commission of the European Communities (TMR award to T.C.S.) for generous financial support. ...

Jonathan W. Burton; J. Stephen Clark; Sam Derrer; Thomas C. Stork; Justin G. Bendall; Andrew B. Holmes

1997-08-13T23:59:59.000Z

478

Dendrochronology and heavy metal depsosition in tree rings of baldcypress  

SciTech Connect (OSTI)

A chronology (1895-present) based on tree-ring increments was constructed for baldcypress (Taxodium distichum L.) trees in Bayou Trepagnier, in southern Louisiana. The best indicator of growth was precipitation in February of the preceding year and October of the 2 previous years. Crossdated cores were used to reconstruct large historical natural environmental perturbations (hurricanes). Heavy metals and organic pollutants from oil refineries and other sources contaminated the bayou commencing in the early 1900s. The Pb and Zn content of 50 trees along Bayou Trepagnier, analyzed in the growth rings of tree cores using x-ray fluorescent spectrometry, produced an historical record of pollution. Highlevels of contamination of Pb, as well as Zn, could be correlated with establishment of petroleum refineries (1916) and dredging (1930-1950) of the area, which created spoil banks containing high levels (ca. 300-1600 mg/kg [ppm] Pb) of heavy metals. Concentrations of Pb, per tree, ranged form 0.6 to 14 mg/kg (ppm). Trees in the upper protion of the bayou (near the refiney) contained an average of 4.5 mg/kg (ppm) Pb; trees in the lower portion averaged 2.2 mg/kg (ppm). Concentrations of Zn per tree ranged from 1.7 to 14.8 mg/kg (ppm), but in contrast with Pb did not correlate with distance from pollution sources; trees averaged 5.5 and 5.4 mg/kg (ppm) Zn in the upper and lower portions, respectively, of Bayou Trepagnier. Levels of Pb and Zn in a control ecosystem, Stinking Bayou, were 1.0 and 5.2 mg/kg (ppm), respectively. 39 refs., 7 figs., 2 tabs.

Latimer, S.D.; Ellgaard, E.G.; Kumar, S.D. [Tulane Univ., New Orleans, LA (United States)] [and others

1996-11-01T23:59:59.000Z

479

The performance of the Los Alamos Proton Storage Ring  

SciTech Connect (OSTI)

The Proton Storage Ring (PSR) now in operation at Los Alamos is a high-current accumulator that generates intense 800-MeV proton pulses for driving the Los Alamos Neutron Scattering Center (LANSCE) spallation source. The ring compresses up to 1000-..mu..s-long macropulses from the LAMPF linac into 250-ns bunches and ejects them to a neutron-production target, providing an output optimized for thermal-neutron-scattering research. The design pulse rate and peak pulse intensity of PSR are 12 Hz and 5.2 . 10/sup 13/ protons per pulse (ppp), yielding 100 ..mu..A average current when full performance is reached. This paper summarizes commissioning results and operational experience in the two years since first beam. The PSR has operated in production at average currents up to 30 ..mu..A and has reached a peak intensity of 3.4 . 10/sup 13/ ppp. These achievements represents 30% and 65% of the design objectives. Higher current production has been inhibited by beam losses during accumulation and extraction. Therefore, experiments to understand loss mechanisms have occupied a large fraction of the commissioning effort. Correction of an extraction-channel aperture restriction identified late in 1986 should dramatically reduce extraction losses, which will permit higher current production in 1987. Beam tests in the 10/sup 13/-ppp range have indicated the presence of a collective instability tentatively identified as transverse. However, by suitable parameter adjustments, the instability threshold can be pushed above the top charge-level attainable with the existing H /sup -/ source.

Lawrence, G.P.

1987-03-01T23:59:59.000Z

480

Instability of a stalled accretion shock: evidence for the advective-acoustic cycle  

E-Print Network [OSTI]

We analyze the linear stability of a stalled accretion shock in a perfect gas with a parametrized cooling function L ~ rho^{beta-alpha} P^alpha. The instability is dominated by the l=1 mode if the shock radius exceeds 2-3 times the accretor radius, depending on the parameters of the cooling function. The growth rate and oscillation period are comparable to those observed in the numerical simulations of Blondin & Mezzacappa (2006). The instability mechanism is analyzed by separately measuring the efficiencies of the purely acoustic cycle and the advective-acoustic cycle. These efficiencies are estimated directly from the eigenspectrum, and also through a WKB analysis in the high frequency limit. Both methods prove that the advective-acoustic cycle is unstable, and that the purely acoustic cycle is stable. Extrapolating these results to low frequency leads us to interpret the dominant mode as an advective-acoustic instability, different from the purely acoustic interpretation of Blondin & Mezzacappa (2006). A simplified characterization of the instability is proposed, based on an advective-acoustic cycle between the shock and the radius r_nabla where the velocity gradients of the stationary flow are strongest. The importance of the coupling region in this mechanism calls for a better understanding of the conditions for an efficient advective-acoustic coupling in a decelerated, nonadiabatic flow, in order to extend these results to core-collapse supernovae.

T. Foglizzo; P. Galletti; L. Scheck; H. -Th. Janka

2006-06-26T23:59:59.000Z

Note: This page contains sample records for the topic "function ring cycle" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Functional Specifications  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Functional Specifications Functional Specifications Services Overview ECS Audio/Video Conferencing Fasterdata IPv6 Network Network Performance Tools (perfSONAR) ESnet OID Registry PGP Key Service Virtual Circuits (OSCARS) OSCARS Case Study Documentation User Manual FAQ Design Specifications Functional Specifications Notifications Publications Authorization Policy Default Attributes Message Security Clients For Developers Interfaces Links Hardware Requirements DOE Grids Service Transition Contact Us Technical Assistance: 1 800-33-ESnet (Inside the US) 1 800-333-7638 (Inside the US) 1 510-486-7600 (Globally) 1 510-486-7607 (Globally) Report Network Problems: trouble@es.net Provide Web Site Feedback: info@es.net Functional Specifications OSCARS Reservation Manager - Functional Specifications Year 3 Update (DRAFT)

482

Hanford River Protection Project Life cycle Cost Modeling Tool to Enhance Mission Planning - 13396  

SciTech Connect (OSTI)

The Life cycle Cost Model (LCM) Tool is an overall systems model that incorporates budget, and schedule impacts for the entire life cycle of the River Protection Project (RPP) mission, and is replacing the Hanford Tank Waste Operations Simulator (HTWOS) model as the foundation of the RPP system planning process. Currently, the DOE frequently requests HTWOS simulations of alternative technical and programmatic strategies for completing the RPP mission. Analysis of technical and programmatic changes can be performed with HTWOS; however, life cycle costs and schedules were previously generated by manual transfer of time-based data from HTWOS to Primavera P6. The LCM Tool automates the preparation of life cycle costs and schedules and is needed to provide timely turnaround capability for RPP mission alternative analyses. LCM is the simulation component of the LCM Tool. The simulation component is a replacement of the HTWOS model with new capability to support life cycle cost modeling. It is currently deployed in G22, but has been designed to work in any full object-oriented language with an extensive feature set focused on networking and cross-platform compatibility. The LCM retains existing HTWOS functionality needed to support system planning and alternatives studies going forward. In addition, it incorporates new functionality, coding improvements that streamline programming and model maintenance, and capability to input/export data to/from the LCM using the LCM Database (LCMDB). The LCM Cost/Schedule (LCMCS) contains cost and schedule data and logic. The LCMCS is used to generate life cycle costs and schedules for waste retrieval and processing scenarios. It uses time-based output data from the LCM to produce the logic ties in Primavera P6 necessary for shifting activities. The LCM Tool is evolving to address the needs of decision makers who want to understand the broad spectrum of risks facing complex organizations like DOE-RPP to understand how near-term programmatic decisions affect life cycle costs and commitments. (authors)

Dunford, Gary [AEM Consulting, LLC, 1201 Jadwin Avenue, Richland, WA 99352 (United States)] [AEM Consulting, LLC, 1201 Jadwin Avenue, Richland, WA 99352 (United States); Williams, David [WIT, Inc., 11173 Oak Fern Court, San Diego, CA 92131 (United States)] [WIT, Inc., 11173 Oak Fern Court, San Diego, CA 92131 (United States); Smith, Rick [Knowledge Systems Design, Inc., 13595 Quaker Hill Cross Rd, Nevada City, CA 95959 (United States)] [Knowledge Systems Design, Inc., 13595 Quaker Hill Cross Rd, Nevada City, CA 95959 (United States)

2013-07-01T23:59:59.000Z

483

Investigation of Brazil Current rings in the confluence region Carlos A. D. Lentini,1  

E-Print Network [OSTI]

Investigation of Brazil Current rings in the confluence region Carlos A. D. Lentini,1 Gustavo J Atlantic. These fields were used to monitor the formation and characteristics of the Brazil Current warm-core anticyclonic rings shed by the first meander trough after poleward excursions of the Brazil Current (BC

484

North Brazil Current rings and transport of southern waters in a high resolution numerical  

E-Print Network [OSTI]

North Brazil Current rings and transport of southern waters in a high resolution numerical of the North Brazil Current (NBC) retroflection and North Brazil Current rings. The model mean and seasonal circulation feature near the western boundary is the North Brazil Current (NBC), which has sources

485

Efficiency Modeling of Tuning Techniques for Silicon Carrier Injection Ring Resonators  

E-Print Network [OSTI]

@tamu.edu Abstract: Modeling of carrier injection ring resonator devices with common thermal tuning and a new dual-bias/thermal leverages both bias and thermal tuning for carrier-injection ring modulators, which provide large refractive common tuning methods considered are thermal and bias (current injection) tuning. Thermal tuning

Palermo, Sam

486

Sediment resuspension and erosion by vortex rings R. J. Munro,1,a  

E-Print Network [OSTI]

Sediment resuspension and erosion by vortex rings R. J. Munro,1,a N. Bethke,2 and S. B. Dalziel2 1; accepted 26 January 2009; published online 8 April 2009 Particle resuspension and erosion induced-ring propagation speed. The critical conditions for resuspension whereby particles are only just resuspended were

Dalziel, Stuart

487

Department of Mechanical Engineering Fall 2010 Lycoming Engines Design of Novel Piston Rings  

E-Print Network [OSTI]

assembly for use in air-cooled aircraft internal combustion engines. Lycoming currently uses two cast iron keystone shaped compression rings and an oil control ring. Objectives The main objective is to deliver. The main design aspects the team focused on were: Improving combustion gas sealing Reducing oil

Demirel, Melik C.

488

Atmospheric Environment 38 (2004) 27792787 First detection of nitrogen from NOx in tree rings: a 15  

E-Print Network [OSTI]

abies; Air pollution; Dendroecology; Nitrogen deposition; Stable isotopes; Nitrogen dioxide 1Atmospheric Environment 38 (2004) 2779­2787 First detection of nitrogen from NOx in tree rings 2004; accepted 27 February 2004 Abstract Nitrogen isotope analysis (d15 N) of tree rings is potentially

489

Trace Elements in Tree Rings: Evidence of Recent and Historical Air Pollution  

E-Print Network [OSTI]

, or both. Tree rings have been used to construct records of climate (1), document heavy metal pollution (2Trace Elements in Tree Rings: Evidence of Recent and Historical Air Pollution C. F. Baes III and S and Historical Air Pollution Abstract. Annual growth rinks from short-leaf pine trees in the Great Smoky

Baes, Fred

490

Optoelectronic Oscillator Based on Fiber Ring Resonator: Overall System Optimization and Phase  

E-Print Network [OSTI]

Optoelectronic Oscillator Based on Fiber Ring Resonator: Overall System Optimization and Phase of an optoelectronic oscillator based on a passive fiber ring resonator. Our experimental results demonstrate existing oscillator of the same type, an active cavity based coupled optoelectronic oscillator. I

Paris-Sud XI, Université de

491

Possibilistic clustering approach to trackless ring Pattern Recognition in RICH counters  

Science Journals Connector (OSTI)

The pattern recognition problem in Ring Imaging CHerenkov (RICH) counters concerns the identification of an unknown number of rings whose centers and radii are assumed to be unknown. In this paper we present an algorithm based on the possibilistic approach ... Keywords: 07.05.Mh, 29.40.Ka, 29.85.+c, Pattern recognition, Possibilistic clustering, RICH counters

A. M. Massone; L. Studer; F. Masulli

2006-02-01T23:59:59.000Z

492

Detailed Studies of a HighDensity Polarized Hydrogen Gas Target for Storage Rings  

E-Print Network [OSTI]

Detailed Studies of a High­Density Polarized Hydrogen Gas Target for Storage Rings Kirsten Zapfe 1 (1996) 293 Abstract A high­density target of polarized atomic hydrogen gas for applications in storage rings was produced by injecting atoms from an atomic beam source into a T­shaped storage cell

493

J. Mol. Biol. (1988) 201, 751-754 Aromatic Rings Act as Hydrogen  

E-Print Network [OSTI]

J. Mol. Biol. (1988) 201, 751-754 Aromatic Rings Act as Hydrogen Bond Acceptors Michael Levitt that there is a significant interaction between a hydrogen bond donor (like the > NH group) and the centre of a benzene ring, which acts as a hydrogen bond acceptor. This interaction, hvdrogen bond, which is about half as strong

Levitt, Michael

494

First law of black ring thermodynamics in higher dimensional dilaton gravity with p+1 strength forms  

SciTech Connect (OSTI)

We derive the first law of black ring thermodynamics in n-dimensional Einstein dilaton gravity with additional (p+1)-form field strength being the simplest generalization of five-dimensional theory containing a stationary black ring solution with dipole charge. It was done by means of choosing any cross section of the event horizon to the future of the bifurcation surface.

Rogatko, Marek [Institute of Physics, Maria Curie-Sklodowska University, 20-031 Lublin, pl. Marii Curie-Sklodowskiej 1 (Poland)

2006-01-15T23:59:59.000Z

495

DEVELOPMENT AND APPLICATIONS OF THE UAL BASED SNS RING SIMULATION ENVIRONMENT.  

SciTech Connect (OSTI)

The SNS Ring off-line parallel simulation environment based on the Unified Accelerator Libraries (UAL) has en implemented and used for extensive full-scale beam dynamics studies arising in high-intensity ring. The paper describes the structure of this environment and its application to various high-intensity topics and diagnostics modeling.

MALITSKY,N.; CAMERON,P.; FEDOTOV,A.V.; SMITH,J.; WEI,J.

2002-04-08T23:59:59.000Z

496

Multiple locus genealogies and phenotypic characters reappraise the causal agents of apple ring rot in China  

E-Print Network [OSTI]

Multiple locus genealogies and phenotypic characters reappraise the causal agents of apple ring rot & Guangyu Sun Received: 6 March 2014 /Accepted: 2 September 2014 # School of Science 2014 Abstract Apple ring rot inflicts severe economic losses in the main apple producing areas of East Asia. The causal

Biggs, Alan R.

497

In Situ Cycle-by-Cycle Flash Annealing of Atomic Layer Deposited Materials  

Science Journals Connector (OSTI)

Furthermore, these large thermal budget heating methods may overheat ALD reactor components such as the chamber O-ring. ... For example, the electrochemical properties of TiO2 have been shown to be dependent on the crystalline phase, with anatase TiO2 having desirable performance in photoelectrochemical applications such as dye-sensitized solar cells and photocatalysis. ...

Michael C. Langston; Neil P. Dasgupta; Hee Joon Jung; Manca Logar; Yu Huang; Robert Sinclair; Fritz B. Prinz

2012-11-02T23:59:59.000Z

498

Discovery of a Splicing Regulator Required for Cell Cycle Progression  

SciTech Connect (OSTI)

In the G1 phase of the cell division cycle, eukaryotic cells prepare many of the resources necessary for a new round of growth including renewal of the transcriptional and protein synthetic capacities and building the machinery for chromosome replication. The function of G1 has an early evolutionary origin and is preserved in single and multicellular organisms, although the regulatory mechanisms conducting G1 specific functions are only understood in a few model eukaryotes. Here we describe a new G1 mutant from an ancient family of apicomplexan protozoans. Toxoplasma gondii temperature-sensitive mutant 12-109C6 conditionally arrests in the G1 phase due to a single point mutation in a novel protein containing a single RNA-recognition-motif (TgRRM1). The resulting tyrosine to asparagine amino acid change in TgRRM1 causes severe temperature instability that generates an effective null phenotype for this protein when the mutant is shifted to the restrictive temperature. Orthologs of TgRRM1 are widely conserved in diverse eukaryote lineages, and the human counterpart (RBM42) can functionally replace the missing Toxoplasma factor. Transcriptome studies demonstrate that gene expression is downregulated in the mutant at the restrictive temperature due to a severe defect in splicing that affects both cell cycle and constitutively expressed mRNAs. The interaction of TgRRM1 with factors of the tri-SNP complex (U4/U6 & U5 snRNPs) indicate this factor may be required to assemble an active spliceosome. Thus, the TgRRM1 family of proteins is an unrecognized and evolutionarily conserved class of splicing regulators. This study demonstrates investigations into diverse unicellular eukaryotes, like the Apicomplexa, have the potential to yield new insights into important mechanisms conserved across modern eukaryotic kingdoms.

Suvorova, Elena S.; Croken, Matthew; Kratzer, Stella; Ting, Li-Min; Conde de Felipe, Magnolia; Balu, Bharath; Markillie, Lye Meng; Weiss, Louis M.; Kim, Kami; White, Michael W.

2013-02-01T23:59:59.000Z

499

Carbon Cycle Engineering | Open Energy Information  

Open Energy Info (EERE)

Cycle Engineering Cycle Engineering Jump to: navigation, search Name Carbon Cycle Engineering Address 13725 Dutch Creek Road Place Athens, Ohio Zip 45701 Sector Biofuels, Biomass, Efficiency, Renewable Energy Product Agriculture; Consulting; Engineering/architectural/design Phone number 740-541-1685 Website http://www.Carboncycleengineer Coordinates 39.376838°, -82.029904° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.376838,"lon":-82.029904,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

500

Large Scale Truck Duty Cycle.pub  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Truck Duty Cycle Evaluation and Truck Duty Cycle Evaluation and Assessment of Fuel Efficiency and Emission Reduction Technologies Oak Ridge National Laboratory managed by UT-Battelle, LLC for the U.S. Department of Energy under Contract number DE-AC05-00OR22725 Research Areas Freight Flows Passenger Flows Supply Chain Efficiency Transportation: Energy Environment Safety Security Vehicle Technologies Research Brief T he Oak Ridge National Laboratory (ORNL) is conducting research to better understand truck fuel economy and emissions in normal everyday use, as part of a study sponsored by the Department of Energy (DOE) Vehicle Technologies Program (VTP). By collecting duty cycle data (velocity, acceleration and elevation) during normal operations of literally thousands of vehicles for an