Powered by Deep Web Technologies
Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

New tools to cut labor costs  

SciTech Connect

The Electric Power Research Institute is developing new techniques that will reduce the labor costs of building and maintaining power-distribution systems. The new tools include a cable plow for underground cables, concrete cutters, an underground borer, tree growth retardants, and other devices which reduce labor requirements and cause less environmental disruption. 2 references. (DCK)

Lihach, N.; Kendrew, T.; Rodenbaugh, T.; Steiner, R.; Tackaberry, R.

1983-03-01T23:59:59.000Z

2

Electric Demand Cost Versus Labor Cost: A Case Study  

E-Print Network (OSTI)

Electric Utility companies charge industrial clients for two things: demand and usage. Depending on type of business and hours operation, demand cost could be very high. Most of the operations scheduling in a plant is achieved considering labor cost. For small plants, it is quite possible that a decrease in labor could result in an increase in electric demand and cost or vice versa. In this paper two cases are presented which highlight the dependence of one on other.

Agrawal, S.; Jensen, R.

1998-04-01T23:59:59.000Z

3

Nuclear fuel cycle costs  

Science Conference Proceedings (OSTI)

The costs for the back-end of the nuclear fuel cycle, which were developed as part of the Nonproliferation Alternative Systems Assessment Program (NASAP), are presented. Total fuel cycle costs are given for the pressurized water reactor once-through and fuel recycle systems, and for the liquid-metal fast breeder reactor system. These calculations show that fuel cycle costs are a small part of the total power costs. For breeder reactors, fuel cycle costs are about half that of the present once-through system. The total power cost of the breeder reactor system is greater than that of light-water reactor at today's prices for uranium and enrichment.

Burch, W.D.; Haire, M.J.; Rainey, R.H.

1982-02-01T23:59:59.000Z

4

Fuel-cycle costs for alternative fuels  

Science Conference Proceedings (OSTI)

This paper compares the fuel cycle cost and fresh fuel requirements for a range of nuclear reactor systems including the present day LWR without fuel recycle, an LWR modified to obtain a higher fuel burnup, an LWR using recycle uranium and plutonium fuel, an LWR using a proliferation resistant /sup 233/U-Th cycle, a heavy water reactor, a couple of HTGRs, a GCFR, and several LMFBRs. These reactor systems were selected from a set of 26 developed for the NASAP study and represent a wide range of fuel cycle requirements.

Rainey, R.H.; Burch, W.D.; Haire, M.J.; Unger, W.E.

1980-01-01T23:59:59.000Z

5

Advanced Fuel Cycle Cost Basis  

SciTech Connect

This report, commissioned by the U.S. Department of Energy (DOE), provides a comprehensive set of cost data supporting a cost analysis for the relative economic comparison of options for use in the Advanced Fuel Cycle Initiative (AFCI) Program. The report describes the AFCI cost basis development process, reference information on AFCI cost modules, a procedure for estimating fuel cycle costs, economic evaluation guidelines, and a discussion on the integration of cost data into economic computer models. This report contains reference cost data for 25 cost modules—23 fuel cycle cost modules and 2 reactor modules. The cost modules were developed in the areas of natural uranium mining and milling, conversion, enrichment, depleted uranium disposition, fuel fabrication, interim spent fuel storage, reprocessing, waste conditioning, spent nuclear fuel (SNF) packaging, long-term monitored retrievable storage, near surface disposal of low-level waste (LLW), geologic repository and other disposal concepts, and transportation processes for nuclear fuel, LLW, SNF, transuranic, and high-level waste.

D. E. Shropshire; K. A. Williams; W. B. Boore; J. D. Smith; B. W. Dixon; M. Dunzik-Gougar; R. D. Adams; D. Gombert; E. Schneider

2008-03-01T23:59:59.000Z

6

Advanced Fuel Cycle Cost Basis  

SciTech Connect

This report, commissioned by the U.S. Department of Energy (DOE), provides a comprehensive set of cost data supporting a cost analysis for the relative economic comparison of options for use in the Advanced Fuel Cycle Initiative (AFCI) Program. The report describes the AFCI cost basis development process, reference information on AFCI cost modules, a procedure for estimating fuel cycle costs, economic evaluation guidelines, and a discussion on the integration of cost data into economic computer models. This report contains reference cost data for 26 cost modules—24 fuel cycle cost modules and 2 reactor modules. The cost modules were developed in the areas of natural uranium mining and milling, conversion, enrichment, depleted uranium disposition, fuel fabrication, interim spent fuel storage, reprocessing, waste conditioning, spent nuclear fuel (SNF) packaging, long-term monitored retrievable storage, near surface disposal of low-level waste (LLW), geologic repository and other disposal concepts, and transportation processes for nuclear fuel, LLW, SNF, and high-level waste.

D. E. Shropshire; K. A. Williams; W. B. Boore; J. D. Smith; B. W. Dixon; M. Dunzik-Gougar; R. D. Adams; D. Gombert

2007-04-01T23:59:59.000Z

7

Advanced Fuel Cycle Cost Basis  

SciTech Connect

This report, commissioned by the U.S. Department of Energy (DOE), provides a comprehensive set of cost data supporting a cost analysis for the relative economic comparison of options for use in the Advanced Fuel Cycle Initiative (AFCI) Program. The report describes the AFCI cost basis development process, reference information on AFCI cost modules, a procedure for estimating fuel cycle costs, economic evaluation guidelines, and a discussion on the integration of cost data into economic computer models. This report contains reference cost data for 25 cost modules—23 fuel cycle cost modules and 2 reactor modules. The cost modules were developed in the areas of natural uranium mining and milling, conversion, enrichment, depleted uranium disposition, fuel fabrication, interim spent fuel storage, reprocessing, waste conditioning, spent nuclear fuel (SNF) packaging, long-term monitored retrievable storage, near surface disposal of low-level waste (LLW), geologic repository and other disposal concepts, and transportation processes for nuclear fuel, LLW, SNF, transuranic, and high-level waste.

D. E. Shropshire; K. A. Williams; W. B. Boore; J. D. Smith; B. W. Dixon; M. Dunzik-Gougar; R. D. Adams; D. Gombert; E. Schneider

2009-12-01T23:59:59.000Z

8

Costs of electronuclear fuel production  

SciTech Connect

The Los Alamos Scientific Laboratory (LASL) proposes to study the electronuclear fuel producer (EFP) as a means of producing fissile fuel to generate electricity. The main advantage of the EFP is that it may reduce the risks of nuclear proliferation by breeding /sup 233/U from thorium, thereby avoiding plutonium separation. A report on the costs of electronuclear fuel production based upon two designs considered by LASL is presented. The findings indicate that the EFP design variations considered are not likely to result in electricity generation costs as low as the uranium fuel cycle used in the US today. At current estimates of annual fuel output (500 kg /sup 233/U per EFP), the costs of electricity generation using fuel produced by the EFP are more than three times higher than generating costs using the traditional fuel cycle. Sensitivity analysis indicates that electronuclear fuel production would become cost competitive with the traditional uranium fuel cycle when U/sub 3/O/sub 8/ (yellowcake) prices approach $1000 per pound.

Flaim, T.; Loose, V.

1978-07-01T23:59:59.000Z

9

Alternative Fuels Data Center: Reynolds Logistics Reduces Fuel Costs With  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Reynolds Logistics Reynolds Logistics Reduces Fuel Costs With EVs to someone by E-mail Share Alternative Fuels Data Center: Reynolds Logistics Reduces Fuel Costs With EVs on Facebook Tweet about Alternative Fuels Data Center: Reynolds Logistics Reduces Fuel Costs With EVs on Twitter Bookmark Alternative Fuels Data Center: Reynolds Logistics Reduces Fuel Costs With EVs on Google Bookmark Alternative Fuels Data Center: Reynolds Logistics Reduces Fuel Costs With EVs on Delicious Rank Alternative Fuels Data Center: Reynolds Logistics Reduces Fuel Costs With EVs on Digg Find More places to share Alternative Fuels Data Center: Reynolds Logistics Reduces Fuel Costs With EVs on AddThis.com... July 23, 2011 Reynolds Logistics Reduces Fuel Costs With EVs F ind out how Reynolds Logistics uses electric vehicles to offset petroleum

10

Evaluation of the Total Cost of Ownership of Fuel Cell-Powered Material Handling Equipment  

DOE Green Energy (OSTI)

This report discusses an analysis of the total cost of ownership of fuel cell-powered and traditional battery-powered material handling equipment (MHE, or more typically 'forklifts'). A number of fuel cell MHE deployments have received funding support from the federal government. Using data from these government co-funded deployments, DOE's National Renewable Energy Laboratory (NREL) has been evaluating the performance of fuel cells in material handling applications. NREL has assessed the total cost of ownership of fuel cell MHE and compared it to the cost of ownership of traditional battery-powered MHE. As part of its cost of ownership assessment, NREL looked at a range of costs associated with MHE operation, including the capital costs of battery and fuel cell systems, the cost of supporting infrastructure, maintenance costs, warehouse space costs, and labor costs. Considering all these costs, NREL found that fuel cell MHE can have a lower overall cost of ownership than comparable battery-powered MHE.

Ramsden, T.

2013-04-01T23:59:59.000Z

11

Alternative Fuels Data Center: Vehicle Cost Calculator  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Vehicle Cost Vehicle Cost Calculator to someone by E-mail Share Alternative Fuels Data Center: Vehicle Cost Calculator on Facebook Tweet about Alternative Fuels Data Center: Vehicle Cost Calculator on Twitter Bookmark Alternative Fuels Data Center: Vehicle Cost Calculator on Google Bookmark Alternative Fuels Data Center: Vehicle Cost Calculator on Delicious Rank Alternative Fuels Data Center: Vehicle Cost Calculator on Digg Find More places to share Alternative Fuels Data Center: Vehicle Cost Calculator on AddThis.com... Vehicle Cost Calculator Vehicle Cost Calculator This tool uses basic information about your driving habits to calculate total cost of ownership and emissions for makes and models of most vehicles, including alternative fuel and advanced technology vehicles. Also

12

New Study Shows Solar Manufacturing Costs Not Driven Primarily by Labor |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Study Shows Solar Manufacturing Costs Not Driven Primarily by Study Shows Solar Manufacturing Costs Not Driven Primarily by Labor New Study Shows Solar Manufacturing Costs Not Driven Primarily by Labor September 5, 2013 - 12:00pm Addthis Production scale, not lower labor costs, drives China's current advantage in manufacturing photovoltaic (PV) solar energy systems, according to a new report released today by the Energy Department's National Renewable Energy Laboratory (NREL) and the Massachusetts Institute of Technology (MIT). Although the prevailing belief is that low labor costs and direct government subsidies for PV manufacturing in China account for that country's dominance in PV manufacturing, the NREL/MIT study shows that a majority of the region's competitive advantage comes from production scale-enabled, in part, through preferred access to capital (indirect

13

New Study Shows Solar Manufacturing Costs Not Driven Primarily by Labor |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

New Study Shows Solar Manufacturing Costs Not Driven Primarily by New Study Shows Solar Manufacturing Costs Not Driven Primarily by Labor New Study Shows Solar Manufacturing Costs Not Driven Primarily by Labor September 5, 2013 - 12:00pm Addthis Production scale, not lower labor costs, drives China's current advantage in manufacturing photovoltaic (PV) solar energy systems, according to a new report released today by the Energy Department's National Renewable Energy Laboratory (NREL) and the Massachusetts Institute of Technology (MIT). Although the prevailing belief is that low labor costs and direct government subsidies for PV manufacturing in China account for that country's dominance in PV manufacturing, the NREL/MIT study shows that a majority of the region's competitive advantage comes from production scale-enabled, in part, through preferred access to capital (indirect

14

Evaluation of Stationary Fuel Cell Deployments, Costs, and Fuels (Presentation)  

SciTech Connect

This presentation summarizes NREL's technology validation of stationary fuel cell systems and presents data on number of deployments, system costs, and fuel types.

Ainscough, C.; Kurtz, J.; Peters, M.; Saur, G.

2013-10-01T23:59:59.000Z

15

GUIDE TO NUCLEAR POWER COST EVALUATION. VOLUME 4. FUEL CYCLE COSTS  

SciTech Connect

Information on fuel cycle cost is presented. Topics covered include: nuclear fuel, fuel management, fuel cost, fissionable material cost, use charge, conversion and fabrication costs, processing cost, and shipping cost. (M.C.G.)

1962-03-15T23:59:59.000Z

16

Fuel-cycle cost comparisons with oxide and silicide fuels  

SciTech Connect

This paper addresses fuel cycle cost comparisons for a generic 10 MW reactor with HEU aluminide fuel and with LEU oxide and silicide fuels in several fuel element geometries. The intention of this study is to provide a consistent assessment of various design options from a cost point of view. Fuel cycle cost benefits could result if a number of reactors were to utilize fuel elements with the same number or different numbers of the same standard fuel plate. Data are presented to quantify these potential cost benefits. This analysis shows that there are a number of fuel element designs using LEU oxide or silicide fuels that have either the same or lower total fuel cycle costs than the HEU design. Use of these fuels with the uranium densities considered requires that they are successfully demonstrated and licensed.

Matos, J.E.; Freese, K.E.

1982-01-01T23:59:59.000Z

17

Cost of Fuel to General Electricity  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of Fuel to Generate Electricity of Fuel to Generate Electricity Cost of Fuel to Generate Electricity Herb Emmrich Gas Demand Forecast, Economic Analysis & Tariffs Manager SCG/SDG&E SCG/SDG&E Federal Utility Partnership Working Group (FUPWG) 2009 Fall Meeting November 18, 2009 Ontario, California The Six Main Costs to Price Electricity are:  Capital costs - the cost of capital investment (debt & equity), depreciation, Federal & State income taxes and property taxes and property taxes  Fuel costs based on fuel used to generate electricity - hydro, natural gas, coal, fuel oil, wind, solar, photovoltaic geothermal biogas photovoltaic, geothermal, biogas  Operating and maintenance costs  Transmission costs  Distribution costs  Social adder costs - GHG adder, low income adder,

18

Breaking the Fuel Cell Cost Barrier  

NLE Websites -- All DOE Office Websites (Extended Search)

Breaking the Fuel Cell Cost Barrier Breaking the Fuel Cell Cost Barrier AMFC Workshop May 8 th , 2011, Arlington, VA Shimshon Gottesfeld, CTO The Fuel Cell Cost Challenge 2 CellEra's goal - achieve price parity with incumbents earlier on in market entry process ! Mainstream Polymer Electrolyte Fuel Cell ( PEM) Cost Barriers 3 Graphite / stainless steel hardware Acidic membrane Platinum based electrodes Cost barriers deeply embedded in core tech materials BOM-based cost barriers - 90% of stack cost Cost volatility - Platinum $500/Oz - $2,500/Oz The possibility of an OH - ion conducting membrane 4 Non-acidic membrane CellEra Took Advantage of this Opportunity A new type of membrane component with potential for strong fuel cell cost cuts was revealed in 2006, but was accompanied by general industry skepticism

19

Fuel cycle cost study with HEU and LEU fuels  

SciTech Connect

Fuel cycle costs are compared for a range of /sup 235/U loadings with HEU and LEU fuels using the IAEA generic 10 MW reactor as an example. If LEU silicide fuels are successfully demonstrated and licensed, the results indicate that total fuel cycle costs can be about the same or lower than those with the HEU fuels that are currently used in most research reactors.

Matos, J.E.; Freese, K.E.

1984-01-01T23:59:59.000Z

20

Work Costs and Nonconvex Preferences in the Estimation of Labor Supply Models  

E-Print Network (OSTI)

We first critique the manner in which work costs have been introduced into labor supply estimation, and note the difficulty of incorporating a realistic rendering of the costs of work. We then show that, if work costs are not acounted for in the budget and time constraints in a structural labor supply model, they will be subsumed into the data generating preferences. We show that even if underlying preferences over consumption and leisure are convex, the presence of unobservable work costs can make these preferences appear nonconvex. Absent strong functional form assumptions, these work costs are not identified in data commonly used for labor supply estimation. However, we show that even if work costs cannot be separately identified, policy relevant calculations, such as estimates of the effect of tax changes on labor supply and deadweight loss calculations, are not affected by the fact that estimated preferences incorporate work costs. We would like to thank Joe Altonji and Chris Taber for valuable conversations, and seminar participants

Bradley T. Heim; Bruce D. Meyer

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Benchmark the Fuel Cost of Steam Generation  

SciTech Connect

This revised ITP tip sheet on benchmarking the fuel cost of steam provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

2006-01-01T23:59:59.000Z

22

Nuclear-fuel-cycle costs. Consolidated Fuel-Reprocessing Program  

Science Conference Proceedings (OSTI)

The costs for the back-end of the nuclear fuel cycle, which were developed as part of the Nonproliferation Alternative Systems Assessment Program (NASAP), are presented. Total fuel-cycle costs are given for the pressurized-water reactor once-through and fuel-recycle systems, and for the liquid-metal fast-breeder-reactor system. These calculations show that fuel-cycle costs are a small part of the total power costs. For breeder reactors, fuel-cycle costs are about half that of the present once-through system. The total power cost of the breeder-reactor system is greater than that of light-water reactor at today's prices for uranium and enrichment.

Burch, W.D.; Haire, M.J.; Rainey, R.H.

1981-01-01T23:59:59.000Z

23

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

3.1 Fuel Cell System Cost Estimate We define the fuel cellto note that these cost estimates are based on a largeother studies on fuel cell cost estimates Baseline gasoline

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

24

HEFA and F-T jet fuel cost analyses  

E-Print Network (OSTI)

Aviation and the Environment 2. HEFA jet fuel from vegetable oil bottom-up cost study 3. HEFA jet fuel from microalgae bottom-up cost

Nick Carter; Michael Bredehoeft; Christoph Wollersheim; Hakan Olcay; James Hileman; Steven Barrett; Website Lae. Mit. Edu

2012-01-01T23:59:59.000Z

25

Evaluation of the Total Cost of Ownership of Fuel Cell-Powered Material Handling Equipment  

SciTech Connect

This report discusses an analysis of the total cost of ownership of fuel cell-powered and traditional battery-powered material handling equipment (MHE, or more typically 'forklifts'). A number of fuel cell MHE deployments have received funding support from the federal government. Using data from these government co-funded deployments, DOE's National Renewable Energy Laboratory (NREL) has been evaluating the performance of fuel cells in material handling applications. NREL has assessed the total cost of ownership of fuel cell MHE and compared it to the cost of ownership of traditional battery-powered MHE. As part of its cost of ownership assessment, NREL looked at a range of costs associated with MHE operation, including the capital costs of battery and fuel cell systems, the cost of supporting infrastructure, maintenance costs, warehouse space costs, and labor costs. Considering all these costs, NREL found that fuel cell MHE can have a lower overall cost of ownership than comparable battery-powered MHE.

Ramsden, T.

2013-04-01T23:59:59.000Z

26

Fuel Cell System Cost for Transporationa--2008 Cost Estimate  

NLE Websites -- All DOE Office Websites (Extended Search)

Fuel Cell System Cost for Fuel Cell System Cost for Transportation-2008 Cost Estimate National Renewable Energy Laboratory 1617 Cole Boulevard * Golden, Colorado 80401-3393 303-275-3000 * www.nrel.gov NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, operated by the Alliance for Sustainable Energy, LLC Contract No. DE-AC36-08-GO28308 Independent Review Published for the U.S. Department of Energy Hydrogen Program NREL/BK-6A1-45457 May 2009 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or

27

Alternative Fuels Data Center: Vehicle Cost Calculator Assumptions and  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Tools Tools Printable Version Share this resource Send a link to Alternative Fuels Data Center: Vehicle Cost Calculator Assumptions and Methodology to someone by E-mail Share Alternative Fuels Data Center: Vehicle Cost Calculator Assumptions and Methodology on Facebook Tweet about Alternative Fuels Data Center: Vehicle Cost Calculator Assumptions and Methodology on Twitter Bookmark Alternative Fuels Data Center: Vehicle Cost Calculator Assumptions and Methodology on Google Bookmark Alternative Fuels Data Center: Vehicle Cost Calculator Assumptions and Methodology on Delicious Rank Alternative Fuels Data Center: Vehicle Cost Calculator Assumptions and Methodology on Digg Find More places to share Alternative Fuels Data Center: Vehicle Cost Calculator Assumptions and Methodology on AddThis.com...

28

Durable, Low Cost, Improved Fuel Cell Membranes  

NLE Websites -- All DOE Office Websites (Extended Search)

Durable, Low-cost, Improved Durable, Low-cost, Improved Fuel Cell Membranes US Department of Energy Office of Hydrogen, Fuel Cells and Infrastructure Technologies Kickoff Meeting, Washington DC, February 13, 2007 Michel Fouré Project Objectives z To develop a low cost (vs. perfluorosulfonated ionomers), durable membrane. z To develop a membrane capable at 80°C at low relative humidity (25-50%). z To develop a membrane capable of operating at 120°C for brief periods of time. z To elucidate membrane degradation and failure mechanisms. U:jen/slides/pres.07/FC kickoff Washington DC 2-13-07 2 Technical Barriers Addressed z Membrane Cost z Membrane Durability z Membrane capability to operate at low relative humidity. z Membrane capability to operate at 120ºC for brief period of times.

29

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

James, A cost comparison of fuel-cell and battery electricHowever, battery electric vehicles have lower fuel cost, usebattery-electric vehicles in terms of weight, volume, GHGs and cost,

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

30

Investigation of low-cost LNG vehicle fuel tank concepts. Final report  

DOE Green Energy (OSTI)

The objective of this study was to investigate development of a low-cost liquid natural gas (LNG) vehicle fuel storage tank with low fuel boil-off, low tank pressure, and high safety margin. One of the largest contributors to the cost of converting a vehicle to LNG is the cost of the LNG fuel tank. To minimize heat leak from the surroundings into the low-temperature fuel, these tanks are designed as cryogenic dewars with double walls separated by an evacuated insulation space containing multi-layer insulation. The cost of these fuel tanks is driven by this double-walled construction, both in terms of materials and labor. The primary focus of the analysis was to try to devise a fuel tank concept that would allow for the elimination of the double-wall requirement. Results of this study have validated the benefit of vacuum/MLI insulation for LNG fuel tanks and the difficulty in identifying viable alternatives. The thickness of a non-vacuum insulation layer would have to be unreasonably large to achieve an acceptable non-venting hold time. Reasonable hold times could be achieved by using an auxiliary tank to accept boil-off vapor from a non-vacuum insulated primary tank, if the vapor in the auxiliary tank can be stored at high pressure. The primary focus of the analysis was to try to devise a fuel tank concept that allowed for the elimination of the double-wall requirement. Thermodynamic relations were developed for analyzing the fuel tank transient response to heat transfer, venting of vapor, and out-flow of either vapor or liquid. One of the major costs associated with conversion of a vehicle to LNG fuel is the cost of the LNG fuel tank. The cost of these tanks is driven by the cryogenic nature of the fuel and by the fundamental design requirements of long non-venting hold times and low storage pressure.

O`Brien, J.E.; Siahpush, A. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States). Idaho National Engineering and Environmental Lab.

1998-02-01T23:59:59.000Z

31

Alternative Fuels Data Center: CNG Shuttles Save Fuel Costs for R&R  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

CNG Shuttles Save Fuel CNG Shuttles Save Fuel Costs for R&R Limousine and Bus to someone by E-mail Share Alternative Fuels Data Center: CNG Shuttles Save Fuel Costs for R&R Limousine and Bus on Facebook Tweet about Alternative Fuels Data Center: CNG Shuttles Save Fuel Costs for R&R Limousine and Bus on Twitter Bookmark Alternative Fuels Data Center: CNG Shuttles Save Fuel Costs for R&R Limousine and Bus on Google Bookmark Alternative Fuels Data Center: CNG Shuttles Save Fuel Costs for R&R Limousine and Bus on Delicious Rank Alternative Fuels Data Center: CNG Shuttles Save Fuel Costs for R&R Limousine and Bus on Digg Find More places to share Alternative Fuels Data Center: CNG Shuttles Save Fuel Costs for R&R Limousine and Bus on AddThis.com... June 1, 2013

32

Fuel Cell Technologies Office: Automotive and MHE Fuel Cell System Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

Automotive and MHE Automotive and MHE Fuel Cell System Cost Analysis (Text Version) to someone by E-mail Share Fuel Cell Technologies Office: Automotive and MHE Fuel Cell System Cost Analysis (Text Version) on Facebook Tweet about Fuel Cell Technologies Office: Automotive and MHE Fuel Cell System Cost Analysis (Text Version) on Twitter Bookmark Fuel Cell Technologies Office: Automotive and MHE Fuel Cell System Cost Analysis (Text Version) on Google Bookmark Fuel Cell Technologies Office: Automotive and MHE Fuel Cell System Cost Analysis (Text Version) on Delicious Rank Fuel Cell Technologies Office: Automotive and MHE Fuel Cell System Cost Analysis (Text Version) on Digg Find More places to share Fuel Cell Technologies Office: Automotive and MHE Fuel Cell System Cost Analysis (Text Version) on AddThis.com...

33

Parametric Study of Front-End Nuclear Fuel Cycle Costs  

Science Conference Proceedings (OSTI)

This study provides an overview of front-end fuel cost components for nuclear plants, specifically uranium concentrates, uranium conversion services, uranium enrichment services, and nuclear fuel fabrication services. A parametric analysis of light-water reactor (LWR) fuel cycle costs is also included in order to quantify the impacts that result from changes in the cost of one or more front-end components on overall fuel cycle costs.

2009-02-20T23:59:59.000Z

34

Cost and Quality of Fuels for Electric Plants  

Reports and Publications (EIA)

Provides comprehensive information concerning the quality, quantity, and cost of fossil fuels used to produce electricity in the United States.

Dean Fennell

2010-12-01T23:59:59.000Z

35

THE NUCLEAR FUEL CYCLE: PROSPECTS FOR REDUCING ITS COST  

SciTech Connect

Nuclear fuel cost of 1.25 mills/kwh would make nuclear power competitive with conventional power in lowcost coal areas if capital and operating costs can be brought to within about 10 percent of those of coal-fired plants. Substantial decreases in fuel fabrication cost are anticipated by 1970: other costs in the fuel cycle are expccted to remain about the same as at present. Unit costs and irradiation levels that would be needed to give a fuel cost of 1.25 mills/kwh are believed to be attainable by 1970. (auth)

Albrecht, W.L.

1959-02-20T23:59:59.000Z

36

Alternative Fuels Data Center: Vehicle Incremental Cost Allocation  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Vehicle Incremental Vehicle Incremental Cost Allocation to someone by E-mail Share Alternative Fuels Data Center: Vehicle Incremental Cost Allocation on Facebook Tweet about Alternative Fuels Data Center: Vehicle Incremental Cost Allocation on Twitter Bookmark Alternative Fuels Data Center: Vehicle Incremental Cost Allocation on Google Bookmark Alternative Fuels Data Center: Vehicle Incremental Cost Allocation on Delicious Rank Alternative Fuels Data Center: Vehicle Incremental Cost Allocation on Digg Find More places to share Alternative Fuels Data Center: Vehicle Incremental Cost Allocation on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Vehicle Incremental Cost Allocation The U.S. General Services Administration (GSA) must allocate the

37

Alternative Fuels Data Center: Natural Gas Rate and Cost Recovery  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Natural Gas Rate and Natural Gas Rate and Cost Recovery Authorization to someone by E-mail Share Alternative Fuels Data Center: Natural Gas Rate and Cost Recovery Authorization on Facebook Tweet about Alternative Fuels Data Center: Natural Gas Rate and Cost Recovery Authorization on Twitter Bookmark Alternative Fuels Data Center: Natural Gas Rate and Cost Recovery Authorization on Google Bookmark Alternative Fuels Data Center: Natural Gas Rate and Cost Recovery Authorization on Delicious Rank Alternative Fuels Data Center: Natural Gas Rate and Cost Recovery Authorization on Digg Find More places to share Alternative Fuels Data Center: Natural Gas Rate and Cost Recovery Authorization on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type

38

DOE Hydrogen Analysis Repository: H2 Fueling Appliances Cost and  

NLE Websites -- All DOE Office Websites (Extended Search)

H2 Fueling Appliances Cost and Performance H2 Fueling Appliances Cost and Performance Project Summary Full Title: H2 Production Infrastructure Analysis - Task 2: Cost and Performance of H2 Fueling Appliances Project ID: 80 Principal Investigator: Brian James Keywords: Costs; steam methane reforming (SMR); autothermal reforming (ATR); hydrogen fueling Purpose The purpose of the analysis was to estimate the capital cost and the resulting cost of hydrogen of several types of methane-fueled hydrogen production systems. A bottoms-up cost analysis was conducted of each system to generate a system design and detailed bill-of-materials. Estimates of the overall capital cost of the hydrogen production appliance were generated. This work supports Systems Analysis Milestone A1. ("Complete techno-economic analysis on production and delivery technologies currently

39

Fuel costs and the retirement of capital goods  

E-Print Network (OSTI)

This paper explores the effect that energy prices and market conditions have on the retirement rates of capital goods using new micro data on aircraft lifetimes and fuel costs. The oil shocks of the 1970s made fuel intensive ...

Goolsbee, Austan Dean

1993-01-01T23:59:59.000Z

40

Back-end costs of alternative nuclear fuel cycles  

Science Conference Proceedings (OSTI)

As part of its charter, the Alternate Fuel Cycle Evaluation Program (AFCEP) was directed to evaluate the back-end of the nuclear fuel cycle in support of the Nonproliferation Alternative Systems Assessment Program (NASAP). The principal conclusion from this study is that the costs for recycling a broad range of reactor fuels will not have a large impact on total fuel cycle costs. For the once-through fuel cycle, the costs of fresh fuel fabrication, irradiated fuel storage, and associated transportation is about 1.2 to 1.3 mills/kWh. For the recycle of uranium and plutonium into thermal reactors, the back-cycle costs (i.e., the costs of irradiated fuel storage, transportation, reprocessing, refabrication, and waste disposal) will be from 3 to 3.5 mills/kWh. The costs for the recycle of uranium and plutonium into fast breeder reactors will be from 4.5 to 5 mills/kWh. Using a radioactive spikant or a denatured /sup 233/U-Th cycle will increase power costs for both recycle cases by about 1 mill/kWh. None of these costs substantially influence the total cost of nuclear power, which is in the range of 4 cents/kWh. The fuel cycle costs used in this study do not include costs incurred prior to fuel fabrication; that is, the cost of the uranium or thorium, the costs for enrichment, or credit for fissile materials in the discharged fuel, which is not recycled with the system.

Rainey, R.H.; Burch, W.D.; Haire, M.J.; Unger, W.E.

1980-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Energy Tips: Benchmark the Fuel Cost of Steam Generation | ENERGY...  

NLE Websites -- All DOE Office Websites (Extended Search)

You are here Home Buildings & Plants Energy Tips: Benchmark the Fuel Cost of Steam Generation Secondary menu About us Press room Contact Us Portfolio Manager Login...

42

Figure 34. Ratio of average per megawatthour fuel costs ...  

U.S. Energy Information Administration (EIA)

Title: Figure 34. Ratio of average per megawatthour fuel costs for natural gas combined-cycle plants to coal-fired steam turbines in the RFC west ...

43

Chapter 4. Receipts and Cost of Fossil Fuels  

U.S. Energy Information Administration (EIA)

74 U.S. Energy Information Administration/Electric Power Monthly June 2012 Chapter 4. Receipts and Cost of Fossil Fuels

44

Emission Control Cost-Effectiveness of Alternative-Fuel Vehicles  

E-Print Network (OSTI)

d Total Battery Capacity (Kwh) Cost per Battery ($)e Totalcosts to consumersto purchase a EV fuel economy in miles per kwhKwh equivalent to per-mile gasoline road tax was included. Table 11 Performance and Cost

Wang, Quanlu; Sperling, Daniel; Olmstead, Janis

1993-01-01T23:59:59.000Z

45

Nuclear fuel fabrication and refabrication cost estimation methodology  

SciTech Connect

The costs for construction and operation of nuclear fuel fabrication facilities for several reactor types and fuels were estimated, and the unit costs (prices) of the fuels were determined from these estimates. The techniques used in estimating the costs of building and operating these nuclear fuel fabrication facilities are described in this report. Basically, the estimation techniques involve detailed comparisons of alternative and reference fuel fabrication plants. Increases or decreases in requirements for fabricating the alternative fuels are identified and assessed for their impact on the capital and operating costs. The impact on costs due to facility size or capacity was also assessed, and scaling factors for the various captial and operating cost categories are presented. The method and rationale by which these scaling factors were obtained are also discussed. By use of the techniques described herein, consistent cost information for a wide variety of fuel types can be obtained in a relatively short period of time. In this study, estimates for 52 fuel fabrication plants were obtained in approximately two months. These cost estimates were extensively reviewed by experts in the fabrication of the various fuels, and, in the opinion of the reviewers, the estimates were very consistent and sufficiently accurate for use in overall cycle assessments.

Judkins, R.R.; Olsen, A.R.

1979-11-01T23:59:59.000Z

46

Emission control cost-effectiveness of alternative-fuel vehicles  

DOE Green Energy (OSTI)

Although various legislation and regulations have been adopted to promote the use of alternative-fuel vehicles for curbing urban air pollution problems, there is a lack of systematic comparisons of emission control cost-effectiveness among various alternative-fuel vehicle types. In this paper, life-cycle emission reductions and life-cycle costs were estimated for passenger cars fueled with methanol, ethanol, liquefied petroleum gas, compressed natural gas, and electricity. Vehicle emission estimates included both exhaust and evaporative emissions for air pollutants of hydrocarbon, carbon monoxide, nitrogen oxides, and air-toxic pollutants of benzene, formaldehyde, 1,3-butadiene, and acetaldehyde. Vehicle life-cycle cost estimates accounted for vehicle purchase prices, vehicle life, fuel costs, and vehicle maintenance costs. Emission control cost-effectiveness presented in dollars per ton of emission reduction was calculated for each alternative-fuel vehicle types from the estimated vehicle life-cycle emission reductions and costs. Among various alternative-fuel vehicle types, compressed natural gas vehicles are the most cost-effective vehicle type in controlling vehicle emissions. Dedicated methanol vehicles are the next most cost-effective vehicle type. The cost-effectiveness of electric vehicles depends on improvements in electric vehicle battery technology. With low-cost, high-performance batteries, electric vehicles are more cost-effective than methanol, ethanol, and liquified petroleum gas vehicles.

Wang, Q. [Argonne National Lab., IL (United States); Sperling, D.; Olmstead, J. [California Univ., Davis, CA (United States). Inst. of Transportation Studies

1993-06-14T23:59:59.000Z

47

Fuel Cell System Cost for Transportation-2008 Cost Estimate (Book)  

DOE Green Energy (OSTI)

Independent review prepared for the U.S. Department of Energy (DOE) Hydrogen, Fuel Cells and Infrastructure Technologies (HFCIT) Program Manager.

Not Available

2009-05-01T23:59:59.000Z

48

Flexible Fuel vehicle cost calculator | Open Energy Information  

Open Energy Info (EERE)

Flexible Fuel vehicle cost calculator Flexible Fuel vehicle cost calculator Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Flexible Fuel Vehicle Cost Calculator Agency/Company /Organization: United States Department of Energy Phase: "Evaluate Options and Determine Feasibility" is not in the list of possible values (Bring the Right People Together, Create a Vision, Determine Baseline, Evaluate Options, Develop Goals, Prepare a Plan, Get Feedback, Develop Finance and Implement Projects, Create Early Successes, Evaluate Effectiveness and Revise as Needed) for this property. User Interface: Website Website: www.afdc.energy.gov/afdc/progs/cost_anal.php?0/E85 Calculate the cost to drive a flex-fueled vehicle (one that can run on either E85 Ethanol or gasoline) on each fuel type.

49

Cost Analysis of Fuel Cell Systems for Transportation  

NLE Websites -- All DOE Office Websites (Extended Search)

Fuel Cell Fuel Cell Systems for Transportation Compressed Hydrogen and PEM Fuel Cell System Discussion Fuel Cell Tech Team FreedomCar Detroit. MI October 20, 2004 TIAX LLC Acorn Park Cambridge, Massachusetts 02140-2390 Ref D0006 SFAA No. DE-SCO2- 98EE50526 Topic 1 Subtopic 1C Agenda EC_2004 10 20 FC Tech Team Presentation 1 1 Project Overview 2 Compressed Hydrogen Storage Cost 3 2004 System Cost Update 4 Appendix Project Overview Approach EC_2004 10 20 FC Tech Team Presentation 2 In our final year of the project, we assessed the cost of compressed hydrogen storage and updated the overall system cost projection. Task 1: PEMFC System Technology Synopsis Task 2: Develop Cost Model and Baseline Estimates Task 3: Identify Opportunities for System Cost Reduction Tasks 4, 5, 6 & 7: Annual Updates

50

Today in Energy - High airline jet fuel costs prompt cost ...  

U.S. Energy Information Administration (EIA)

Energy Information Administration ... and idling time. ... Delta stated that it anticipates cost savings of $300 million per year as a result of this ...

51

Labor costs may be reduced . . . Research yields size-controlling rootstocks for peach production  

E-Print Network (OSTI)

Doyle David Ramming Production costs in peaches are highlyby UC and USDA. production costs could be substantiallyDRAFT T he annual production costs for peaches grown in

DeJong, Theodore M.; Johnson, R. Scott; Doyle, James F.; Ramming, David

2005-01-01T23:59:59.000Z

52

Automotive and MHE Fuel Cell System Cost Analysis  

NLE Websites -- All DOE Office Websites (Extended Search)

Vince Contini, Kathya Mahadevan, Fritz Eubanks, Vince Contini, Kathya Mahadevan, Fritz Eubanks, Jennifer Smith, Gabe Stout and Mike Jansen Battelle April 16, 2013 Manufacturing Cost Analysis of Fuel Cells for Material Handling Applications 2 Presentation Outline * Background * Approach * System Design * Fuel Cell Stack Design * Stack, BOP and System Cost Models * System Cost Summary * Results Summary 3 * 10 and 25 kW PEM Fuel Cells for Material Handling Equipment (MHE) applications Background 5-year program to provide feedback to DOE on evaluating fuel cell systems for stationary and emerging markets by developing independent models and cost estimates * Applications - Primary (including CHP) power, backup power, APU, and material handling * Fuel Cell Types - 80°C PEM, 180°C PEM, SOFC technologies

53

Energy Department Announces New Investment to Reduce Fuel Cell Costs |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

New Investment to Reduce Fuel Cell New Investment to Reduce Fuel Cell Costs Energy Department Announces New Investment to Reduce Fuel Cell Costs August 1, 2013 - 12:00pm Addthis In support of the Obama Administration's all-of-the-above strategy to develop clean, domestic energy sources, the Energy Department today announced a $4.5 million investment in two projects-led by Minnesota-based 3M and the Colorado School of Mines-to lower the cost, improve the durability, and increase the efficiency of next-generation fuel cell systems. This investment is a part of the Energy Department's commitment to maintain American leadership in innovative clean energy technologies, give American businesses more options to cut energy costs, and reduce our reliance on imported oil. "Fuel cell technologies have an important role to play in diversifying

54

Energy Tips: Benchmark the Fuel Cost of Steam Generation  

NLE Websites -- All DOE Office Websites (Extended Search)

Type (sales unit) Type (sales unit) Energy Content Combustion (Btu/sales unit) Efficiency (%) Natural Gas (therm) 100,000 81.7 Natural Gas (cubic foot) 1,030 81.7 Distillate/No. 2 Oil (gallon) 138,700 84.6 Residual/No. 6 Oil (gallon) 149,700 86.1 Coal (ton) 27,000,000 87.6 Benchmark the Fuel Cost of Steam Generation Benchmarking the fuel cost of steam generation ($/1000 lbs of steam) is an effective way to assess the efficiency of your steam system. This cost is dependent upon fuel type, unit fuel cost, boiler efficiency, feedwater temperature, and steam pressure. This calculation provides a good first approximation for the cost of generating steam and serves as a tracking device to allow for boiler performance monitoring. Table 1 shows the heat input required to produce one pound of saturated

55

Performance and fuel cycle cost study of the R2 reactor with HEU and LEU fuels  

SciTech Connect

A systematic study of the experiment performance and fuel cycle costs of the 50 MW R2 reactor operated by Studsvik Energiteknik AB has been performed using the current R2 HEU fuel, a variety of LEU fuel element designs, and two core-box/reflector configurations. The results include the relative performance of both in-core and ex-core experiments, control rod worths, and relative annual fuel cycle costs.

Pond, R.B.; Freese, K.E.; Matos, J.E.

1984-01-01T23:59:59.000Z

56

FUEL CELLS IN SHIPPING: HIGHER CAPITAL COSTS AND REDUCED FLEXIBILITY  

E-Print Network (OSTI)

Abstract: The paper discusses some main economic characteristics of fuel cell power production technology applied to shipping. Whenever competitive fuel cell systems enter the market, they are likely to have higher capital costs and lower operating costs than systems based on traditional combustion technology. Implications of the difference are investigated with respect to investment flexibility by the use of a real options model of ship investment, lay-up and scrapping decisions under freight rate uncertainty. A higher capital share of total expected costs can represent a significant opportunity cost in uncertain markets. The paper highlights the significance of accounting properly for value of flexibility prior to investment in new technology.

Sigbjørn Sødal

2003-01-01T23:59:59.000Z

57

Figure 33. Ratio of average per megawatthour fuel costs for ...  

U.S. Energy Information Administration (EIA)

Sheet3 Sheet2 Sheet1 Figure 33. Ratio of average per megawatthour fuel costs for natural gas combined-cycle plants to coal-fired steam turbines in the SERC southeast ...

58

Figure 27. Ratio of average per megawatthour fuel costs for ...  

U.S. Energy Information Administration (EIA)

Sheet3 Sheet2 Sheet1 Figure 27. Ratio of average per megawatthour fuel costs for natural gas combined-cycle plants to coal-fired steam turbines in five cases, 2008-2040

59

Accurate Detection of Impurities in Hydrogen Fuel at Lower Cost  

Scientists at Argonne National Laboratory have developed two alternative strategies for detecting impurities in the hydrogen used in fuel cells. Both yield highly accurate results and use simpler, less costly equipment. As the United States gradually ...

60

Low Cost Reversible fuel cell systems  

DOE Green Energy (OSTI)

This final report summarizes a 3-phase program performed from March 2000 through September 2003 with a particular focus on Phase III. The overall program studied TMI's reversible solid oxide stack, system concepts, and potential applications. The TMI reversible (fuel cell-electrolyzer) system employs a stack of high temperature solid-oxide electrochemical cells to produce either electricity (from a fuel and air or oxygen) or hydrogen (from water and supplied electricity). An atmospheric pressure fuel cell system operates on natural gas (or other carbon-containing fuel) and air. A high-pressure reversible electrolyzer system is used to make high-pressure hydrogen and oxygen from water and when desired, operates in reverse to generate electricity from these gases.

Technology Management Inc.

2003-12-30T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Cost and quality of fuels for electric plants 1993  

Science Conference Proceedings (OSTI)

The Cost and Quality of Fuels for Electric Utility Plants (C&Q) presents an annual summary of statistics at the national, Census division, State, electric utility, and plant levels regarding the quantity, quality, and cost of fossil fuels used to produce electricity. The purpose of this publication is to provide energy decision-makers with accurate and timely information that may be used in forming various perspectives on issues regarding electric power.

Not Available

1994-07-01T23:59:59.000Z

62

Cost-effective fuel cycle closure  

SciTech Connect

The U.S. government is moving toward meeting its obligation to accept spent fuel from commercial light water reactors (LWRs) in 1998 by providing an interim storage facility. Site work and analysis of the deep, geologic repository at Yucca Mountain will continue at a reduced level of effort. This provides the time required to reevaluate the use of spent-fuel recycling instead of direct disposal. A preliminary assessment of this option is presented in this paper.

Ehrman, C.S. [Burns & Roe, Inc., Oradell, NJ (United States); Boardman, C.E. [General Electric Company, San Jose, CA (United States)

1995-12-31T23:59:59.000Z

63

DOE Hydrogen and Fuel Cells Program Record 5005: Fuel Cell System Cost - 2002 versus 2005  

NLE Websites -- All DOE Office Websites (Extended Search)

5 Date: March 20, 2005 5 Date: March 20, 2005 Title: Fuel Cell System Cost - 2002 vs 2005 Originator: Patrick Davis Approved by: JoAnn Milliken Date: May 22, 2006 Item: "Reduced the high-volume cost of automotive fuel cells from $275/kW (50kW system) in 2002 to $110/kW (80kW system) in 2005." Supporting Information: In 2002, TIAX reported a cost of $324/kW for a 50-kW automotive PEM fuel cell system operating on gasoline reformate, based on their modeling of projected cost for 500,000 units per year. See Eric Carlson et al., "Cost Analyses of Fuel Cell Stack/System." U.S. DOE Hydrogen Program Annual Progress Report. (2002) at http://www.eere.energy.gov/hydrogenandfuelcells/pdfs/33098_sec4-1.pdf. Also see "Cost Modeling of PEM Fuel Cell Systems for Automobiles," Eric Carlson et al., SAE

64

Fuel Cell System for Transportation -- 2005 Cost Estimate  

Science Conference Proceedings (OSTI)

Independent review report of the methodology used by TIAX to estimate the cost of producing PEM fuel cells using 2005 cell stack technology. The U.S. Department of Energy (DOE) Hydrogen, Fuel Cells and Infrastructure Technologies Program Manager asked the National Renewable Energy Laboratory (NREL) to commission an independent review of the 2005 TIAX cost analysis for fuel cell production. The NREL Systems Integrator is responsible for conducting independent reviews of progress toward meeting the DOE Hydrogen Program (the Program) technical targets. An important technical target of the Program is the proton exchange membrane (PEM) fuel cell cost in terms of dollars per kilowatt ($/kW). The Program's Multi-Year Program Research, Development, and Demonstration Plan established $125/kW as the 2005 technical target. Over the last several years, the Program has contracted with TIAX, LLC (TIAX) to produce estimates of the high volume cost of PEM fuel cell production for transportation use. Since no manufacturer is yet producing PEM fuel cells in the quantities needed for an initial hydrogen-based transportation economy, these estimates are necessary for DOE to gauge progress toward meeting its targets. For a PEM fuel cell system configuration developed by Argonne National Laboratory, TIAX estimated the total cost to be $108/kW, based on assumptions of 500,000 units per year produced with 2005 cell stack technology, vertical integration of cell stack manufacturing, and balance-of-plant (BOP) components purchased from a supplier network. Furthermore, TIAX conducted a Monte Carlo analysis by varying ten key parameters over a wide range of values and estimated with 98% certainty that the mean PEM fuel cell system cost would be below DOE's 2005 target of $125/kW. NREL commissioned DJW TECHNOLOGY, LLC to form an Independent Review Team (the Team) of industry fuel cell experts and to evaluate the cost estimation process and the results reported by TIAX. The results of this independent review will permit NREL and DOE to better understand the credibility of the TIAX cost estimation process and to implement changes in future cost analyses, if necessary. The Team found the methodology used by TIAX to estimate the cost of producing PEM fuel cells to be reasonable and, using 2005 cell stack technology and assuming production of 500,000 units per year, to have calculated a credible cost of $108/kW.

Wheeler, D.

2006-10-01T23:59:59.000Z

65

EFFECT OF REDUCED U-235 PRICE ON FUEL CYCLE COSTS  

SciTech Connect

A study was made to determine the effect of changes in natural uranium cost and in separative work charges on fuel cycle costs in nuclear power plants. Reactors considered were a Dresden-type boiling water reactor (BWR) and a Yankee- type pressurized water reactor (PWR), with net power ratings of 100, 300, and 500 Mwe. Fuel cycle costs were calculated for these reactors, using either enriched uranium or U/sup 235/-thorium as the fuel material. The price schedule for uranium was based on a feed material cost of /kg uranium as UF/sub 6/ and separative work costs of /kg uranium (Schedule B) and /kg uranium (Schedule C). The present AEC price schedule for enriched uranium was also used for purposes of a reference case. The results indicate that a reduction in present enriched uranium price to that given by Schedule B would reduce fuel cycle costs for the BWR plants by 0.4 to 0.5 mill/kwh for the enriched-uranium cycle, and 0.4 to 0.7 mill/kwh for the thorium cycle. Reductions in fuel cycle costs for the PWR plants were 0.5 to 0.7 and 0.4 to 0.75 mill/kwh, respectively, for the same situations. (auth)

Bennett, L.L.

1962-03-01T23:59:59.000Z

66

Agricultural scientists cut alcohol fuel costs  

Science Conference Proceedings (OSTI)

Scientists at the US Department of Agriculture have succeeded in lowering the cost of making alcohol from corn by 15 cents to $1.64 per gallon. The cost of drying distillers' solubles dropped because at the end of each cooking/fermenting/distilling run, the solubles are used for cooking, cooling and fermenting in the next run. One evaporation of solubles is required after 10 runs, so energy cost is cut from 17 cents to 1.7 cents. The protein by-products recovered, can be used as swine and poultry feeds and as human food.

Not Available

1981-09-21T23:59:59.000Z

67

Benchmark the Fuel Cost of Steam Generation  

DOE Green Energy (OSTI)

BestPractices Steam tip sheet regarding ways to assess steam system efficiency. To determine the effective cost of steam, use a combined heat and power simulation model that includes all the significant effects.

Papar, R. [U.S. Department of Energy (US)

2000-12-04T23:59:59.000Z

68

DOE Hydrogen Program Record 10004, Fuel Cell System Cost - 2010  

NLE Websites -- All DOE Office Websites (Extended Search)

Program Record Program Record Record #: 10004 Date: September 16, 2010 Title: Fuel Cell System Cost - 2010 Update to: Record 9012 Originator: Jacob Spendelow and Jason Marcinkoski Approved by: Sunita Satyapal Date: December 16, 2010 Item: The cost of an 80-kW net automotive polymer electrolyte membrane (PEM) fuel cell system based on 2010 technology and operating on direct hydrogen is projected to be $51/kW when manufactured at a volume of 500,000 units/year. Rationale: In fiscal year 2010, TIAX LLC (TIAX) and Directed Technologies, Inc. (DTI) each updated their 2009 cost analyses of 80-kW net direct hydrogen PEM automotive fuel cell systems based on 2010 technology and projected to manufacturing volumes of 500,000 units per year [1,2]. Both cost estimates are based on performance at beginning of life.

69

Pulverizer performance upgrades lower fuel costs  

Science Conference Proceedings (OSTI)

Between 2002 and 2005, combustion equipment modifications were carried out at St. Johns River Power Plant in Jacksonville, FL. The effort succeeded in obtaining the desired emission reductions and to increase petroleum coke consumption. Since 2005 the boilers typically fired a blend of 70% Colombia coal and 30% delayed petroleum coke. To realize significant fuel savings, the pulverizer capacity was increased by 14% to allow a lower grade coal to be used. The article describes the changes made to the pulverizer to allow 11,800 Btu/pound coal to be burnt, with annual savings of $6.3 m beginning in 2006. 4 figs., 1 tab.

Hansen, T.

2007-05-15T23:59:59.000Z

70

DOE Fuel Cell Technologies Program Record 12020: Fuel Cell System Cost - 2012  

NLE Websites -- All DOE Office Websites (Extended Search)

Record Record Record #: 12020 Date: August 21, 2012 Title: Fuel Cell System Cost - 2012 Update to: Record 11012 Originator: Jacob Spendelow and Jason Marcinkoski Approved by: Sunita Satyapal Date: September 14, 2012 Item: The cost of an 80-kW net automotive polymer electrolyte membrane (PEM) fuel cell system based on 2012 technology 1 and operating on direct hydrogen is projected to be $47/kW when manufactured at a volume of 500,000 units/year. Rationale: The DOE Fuel Cell Technologies Program supports analysis projects that perform detailed analysis to estimate cost status of fuel cell systems, updated on an annual basis [1]. In fiscal year 2012, Strategic Analysis, Inc. (SA) updated their 2011 cost analysis of an 80-kW net direct hydrogen PEM automotive fuel cell system, based on 2012 technology and projected to a

71

Cost and Quality of Fuels for Electric Utility Plants  

Gasoline and Diesel Fuel Update (EIA)

1) 1) Distribution Category UC-950 Cost and Quality of Fuels for Electric Utility Plants 2001 March 2004 Energy Information Administration Office of Coal, Nuclear, Electric and Alternate Fuels U.S. Department of Energy Washington DC 20585 This report was prepared by the Energy Information Administration, the independent statistical and analytical agency within the Department of Energy. The information contained herein should not be construed as advocating or reflecting any policy position of the Department of Energy or any other organization. Preface Background The Cost and Quality of Fuels for Electric Utility Plants 2001 is prepared by the Electric Power Divi- sion; Office of Coal, Nuclear, Electric and Alternate Fuels; Energy Information Administration (EIA); U.S.

72

Methodology for estimating reprocessing costs for nuclear fuels  

Science Conference Proceedings (OSTI)

A technological and economic evaluation of reprocessing requirements for alternate fuel cycles requires a common assessment method and a common basis to which various cycles can be related. A methodology is described for the assessment of alternate fuel cycles utilizing a side-by-side comparison of functional flow diagrams of major areas of the reprocessing plant with corresponding diagrams of the well-developed Purex process as installed in the Barnwell Nuclear Fuel Plant (BNFP). The BNFP treats 1500 metric tons of uranium per year (MTU/yr). Complexity and capacity factors are determined for adjusting the estimated facility and equipment costs of BNFP to determine the corresponding costs for the alternate fuel cycle. Costs of capacities other than the reference 1500 MT of heavy metal per year are estimated by the use of scaling factors. Unit costs of reprocessed fuel are calculated using a discounted cash flow analysis for three economic bases to show the effect of low-risk, typical, and high-risk financing methods.

Carter, W. L.; Rainey, R. H.

1980-02-01T23:59:59.000Z

73

Hydrogen as a transportation fuel: Costs and benefits  

SciTech Connect

Hydrogen fuel and vehicles are assessed and compared to other alternative fuels and vehicles. The cost, efficiency, and emissions of hydrogen storage, delivery, and use in hybrid-electric vehicles (HEVs) are estimated. Hydrogen made thermochemically from natural gas and electrolytically from a range of electricity mixes is examined. Hydrogen produced at central plants and delivered by truck is compared to hydrogen produced on-site at filling stations, fleet refueling centers, and residences. The impacts of hydrogen HEVs, fueled using these pathways, are compared to ultra-low emissions gasoline internal-combustion-engine vehicles (ICEVs), advanced battery-powered electric vehicles (BPEVs), and HEVs using gasoline or natural gas.

Berry, G.D.

1996-03-01T23:59:59.000Z

74

DOE Fuel Cell Technologies Office Record 13012: Fuel Cell System Cost - 2013  

NLE Websites -- All DOE Office Websites (Extended Search)

Office Record Office Record Record #: 13012 Date: September 18, 2013 Title: Fuel Cell System Cost - 2013 Update to: Record 12020 Originator: Jacob Spendelow and Jason Marcinkoski Approved by: Sunita Satyapal Date: October 16, 2013 Item: The cost of an 80-kW net automotive polymer electrolyte membrane (PEM) fuel cell system based on 2013 technology 1 and operating on direct hydrogen is projected to be $67/kW when manufactured at a volume of 100,000 units/year, and $55/kW at 500,000 units/year. Rationale: The DOE Fuel Cell Technologies (FCT) Office supports projects that perform detailed analysis to estimate cost status of fuel cell systems, updated on an annual basis [1]. In fiscal year 2013, Strategic Analysis, Inc. (SA) updated their 2012 cost analysis of an 80-kW

75

The importance of vehicle costs, fuel prices, and fuel efficiency to HEV market success.  

DOE Green Energy (OSTI)

Toyota's introduction of a hybrid electric vehicle (HEV) named ''Prius'' in Japan and Honda's proposed introduction of an HEV in the United States have generated considerable interest in the long-term viability of such fuel-efficient vehicles. A performance and cost projection model developed entirely at Argonne National Laboratory (ANL) is used here to estimate costs. ANL staff developed fuel economy estimates by extending conventional vehicle (CV) modeling done primarily under the National Cooperative Highway Research Program. Together, these estimates are employed to analyze dollar costs vs. benefits of two of many possible HEV technologies. We project incremental costs and fuel savings for a Prius-type low-performance hybrid (14.3 seconds zero to 60 mph acceleration, 260 time) and a higher-performance ''mild'' hybrid vehicle, or MHV (11 seconds 260 time). Each HEV is compared to a U.S. Toyota Corolla with automatic transmission (11 seconds 260 time). The base incremental retail price range, projected a decade hence, is $3,200-$3,750, before considering battery replacement cost. Historical data are analyzed to evaluate the effect of fuel price on consumer preferences for vehicle fuel economy, performance, and size. The relationship between fuel price, the level of change in fuel price, and consumer attitude toward higher fuel efficiency is also evaluated. A recent survey on the value of higher fuel efficiency is presented and U.S. commercial viability of the hybrids is evaluated using discount rates of 2090 and 870. Our analysis, with our current HEV cost estimates and current fuel savings estimates, implies that the U.S. market for such HEVS would be quite limited.

Santini, D. J.; Patterson, P. D.; Vyas, A. D.

1999-12-08T23:59:59.000Z

76

Cost and quality of fuels for electric utility plants, 1994  

Science Conference Proceedings (OSTI)

This document presents an annual summary of statistics at the national, Census division, State, electric utility, and plant levels regarding the quantity, quality, and cost of fossil fuels used to produce electricity. Purpose of this publication is to provide energy decision-makers with accurate, timely information that may be used in forming various perspectives on issues regarding electric power.

NONE

1995-07-14T23:59:59.000Z

77

Cost and quality of fuels for electric utility plants, 1992  

Science Conference Proceedings (OSTI)

This publication presents an annual summary of statistics at the national, Census division, State, electric utility, and plant levels regarding the quantity, quality, and cost of fossil fuels used to produce electricity. The purpose of this publication is to provide energy decision-makers with accurate and timely information that may be used in forming various perspectives on issues regarding electric power.

Not Available

1993-08-02T23:59:59.000Z

78

BIOMASS FOR HYDROGEN AND OTHER TRANSPORT FUELS -POTENTIALS, LIMITATIONS & COSTS  

E-Print Network (OSTI)

BIOMASS FOR HYDROGEN AND OTHER TRANSPORT FUELS - POTENTIALS, LIMITATIONS & COSTS Senior scientist - "Towards Hydrogen Society" ·biomass resources - potentials, limits ·biomass carbon cycle ·biomass for hydrogen - as compared to other H2- sources and to other biomass paths #12;BIOMASS - THE CARBON CYCLE

79

Cost and Quality of Fuels for Electric Utility Plants 1997  

Gasoline and Diesel Fuel Update (EIA)

7 Tables 7 Tables May 1998 Energy Information Administration Office of Coal, Nuclear, Electric and Alternate Fuels U.S. Department of Energy Washington DC 20585 This report was prepared by the Energy Information Administration, the independent statistical and analytical agency within the Department of Energy. The information contained herein should not be construed as advocating or reflecting any policy position of the Department of Energy or any other organization. Energy Information Administration/Cost and Quality of Fuels for Electric Utility Plants 1997 Tables ii Contacts The annual publication Cost and Quality of Fuels for Electric Utility Plants (C&Q) is no longer published by the EIA. The tables presented in this document are intended to replace that annual publication. Questions

80

Lightweighting Impacts on Fuel Economy, Cost, and Component Losses  

DOE Green Energy (OSTI)

The Future Automotive Systems Technology Simulator (FASTSim) is the U.S. Department of Energy's high-level vehicle powertrain model developed at the National Renewable Energy Laboratory. It uses a time versus speed drive cycle to estimate the powertrain forces required to meet the cycle. It simulates the major vehicle powertrain components and their losses. It includes a cost model based on component sizing and fuel prices. FASTSim simulated different levels of lightweighting for four different powertrains: a conventional gasoline engine vehicle, a hybrid electric vehicle (HEV), a plug-in hybrid electric vehicle (PHEV), and a battery electric vehicle (EV). Weight reductions impacted the conventional vehicle's efficiency more than the HEV, PHEV and EV. Although lightweighting impacted the advanced vehicles' efficiency less, it reduced component cost and overall costs more. The PHEV and EV are less cost effective than the conventional vehicle and HEV using current battery costs. Assuming the DOE's battery cost target of $100/kWh, however, the PHEV attained similar cost and lightweighting benefits. Generally, lightweighting was cost effective when it costs less than $6/kg of mass eliminated.

Brooker, A. D.; Ward, J.; Wang, L.

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Vehicle Technologies Office: Fact #407: January 16, 2006 Vehicle Fuel Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

7: January 16, 7: January 16, 2006 Vehicle Fuel Cost vs. Home Heating Cost: Which Causes More Concern? to someone by E-mail Share Vehicle Technologies Office: Fact #407: January 16, 2006 Vehicle Fuel Cost vs. Home Heating Cost: Which Causes More Concern? on Facebook Tweet about Vehicle Technologies Office: Fact #407: January 16, 2006 Vehicle Fuel Cost vs. Home Heating Cost: Which Causes More Concern? on Twitter Bookmark Vehicle Technologies Office: Fact #407: January 16, 2006 Vehicle Fuel Cost vs. Home Heating Cost: Which Causes More Concern? on Google Bookmark Vehicle Technologies Office: Fact #407: January 16, 2006 Vehicle Fuel Cost vs. Home Heating Cost: Which Causes More Concern? on Delicious Rank Vehicle Technologies Office: Fact #407: January 16, 2006 Vehicle Fuel Cost vs. Home Heating Cost: Which Causes More Concern? on Digg

82

SOLID OXIDE FUEL CELL MANUFACTURING COST MODEL: SIMULATING RELATIONSHIPS BETWEEN PERFORMANCE, MANUFACTURING, AND COST OF PRODUCTION  

DOE Green Energy (OSTI)

The successful commercialization of fuel cells will depend on the achievement of competitive system costs and efficiencies. System cost directly impacts the capital equipment component of cost of electricity (COE) and is a major contributor to the O and M component. The replacement costs for equipment (also heavily influenced by stack life) is generally a major contributor to O and M costs. In this project, they worked with the SECA industrial teams to estimate the impact of general manufacturing issues of interest on stack cost using an activities-based cost model for anode-supported planar SOFC stacks with metallic interconnects. An earlier model developed for NETL for anode supported planar SOFCs was enhanced by a linkage to a performance/thermal/mechanical model, by addition of Quality Control steps to the process flow with specific characterization methods, and by assessment of economies of scale. The 3-dimensional adiabatic performance model was used to calculate the average power density for the assumed geometry and operating conditions (i.e., inlet and exhaust temperatures, utilization, and fuel composition) based on publicly available polarizations curves. The SECA team provided guidance on what manufacturing and design issues should be assessed in this Phase I demonstration of cost modeling capabilities. They considered the impact of the following parameters on yield and cost: layer thickness (i.e., anode, electrolyte, and cathode) on cost and stress levels, statistical nature of ceramic material failure on yield, and Quality Control steps and strategies. In this demonstration of the capabilities of the linked model, only the active stack (i.e., anode, electrolyte, and cathode) and interconnect materials were included in the analysis. Factory costs are presented on an area and kilowatt basis to allow developers to extrapolate to their level of performance, stack design, materials, seal and system configurations, and internal corporate overheads and margin goals.

Eric J. Carlson; Yong Yang; Chandler Fulton

2004-04-20T23:59:59.000Z

83

Fuel cost adjustments: An idea whose time has gone  

SciTech Connect

Fuel adjustment clauses, now clearly unneeded, are a disincentive to efficient utility planning and operation. They have no place in a competitive marketplace and should not be turned into incentive regulation as some would do. As competition grow stronger, the case for abandoning FACs also grows stronger. Despite recent proposals that FACs be modified to serve conservation goals or to become incentive regulations, FACs are poor instruments to prod utilities toward conservation or efficiency. Recent developments in fuel markets fully warrant removing FACs and replacing them with traditional cost-of-service regulation. There is a final reason to end fuel clauses; the electric industry's inevitable transition to competition will be easier and more efficient under old-style regulation than under FACs.

Michaels, R.J.

1994-02-01T23:59:59.000Z

84

THORIUM BREEDER REACTOR EVALUATION. PART 1. FUEL YIELD AND FUEL CYCLE COSTS IN FIVE THERMAL BREEDERS  

SciTech Connect

The performances of aqueous-homogeneous (AHBR), molten-salt (MSBR), liquid-bismuth (LBBR), gas-cooled graphite-moderated (GGBR), and deuterium- moderated gas-cooled (DGBR) breeder reactors were evaluated in respect to fuel yield, fuel cycle costs, and development status. A net electrical plant capability of 1000 Mwe was selected, and the fuel and fertile streams were processed continuously on-site. The maximum annual fuel yields were 1.5 mills/ kwhr. The minimum estimated fuel cycle costs were 0.9, 0.6, 1.0, 1.2, and 1.3 mills/kwhr at fuel yields of were 0.9, 0.9, 1.5, 1.5, and 1.3 mills/kwhr. Only the AHBR and the MSBR are capable of achieving fuel yields substantially in excess of 4%/yr, and therefore, in view of the uncertainties in nuclear data and efficiencies of processing methods, only these two can be listed with confidence as being able to satisfy the main criterion of the AEC longrange thorium breeder program, viz. a doubling time of 25 years or less. The development effort required to bring the various concepts to the stage where a prototype station could be designed was estimated to be least for the AHBR, somewhat more for the MSBR, and several times as much for the other systems. The AHBR was judged to rank first in regard to nuclear capability, fuel cycle potential, and status of development. (auth)

Alexander, L.G.; Carter, W.L.; Chapman, R.H.; Kinyon, R.W.; Miller, J.W.; Van Winkle, R.

1961-05-24T23:59:59.000Z

85

DOE Hydrogen and Fuel Cells Program Record 11012: Fuel Cell System Cost - 2011  

NLE Websites -- All DOE Office Websites (Extended Search)

2 Date: August 17, 2011 2 Date: August 17, 2011 Title: Fuel Cell System Cost - 2011 Update to: Record 10004 Originator: Jacob Spendelow and Jason Marcinkoski Approved by: Sunita Satyapal Date: September 7, 2011 Item: The cost of an 80-kW net automotive polymer electrolyte membrane (PEM) fuel cell system based on 2011 technology 1 and operating on direct hydrogen is projected to be $49/kW when manufactured at a volume of 500,000 units/year. Rationale: In fiscal year 2011, Strategic Analysis, Inc. (SA) 2 updated the 2010 Directed Technologies, Inc. (DTI) cost analysis of 80-kW net direct hydrogen PEM automotive fuel cell systems, based on 2011 technology and projected to a manufacturing volume of 500,000 units per year [1]. Results from the analysis were communicated to the DOE

86

DOE Hydrogen and Fuel Cells Program Record 8002: Fuel Cell System Cost - 2007  

NLE Websites -- All DOE Office Websites (Extended Search)

02 Date: October 31, 2008 02 Date: October 31, 2008 Title: Fuel Cell System Cost - 2007 Update to: Record 5005 Originator: Nancy Garland and Jason Marcinkoski Approved by: Sunita Satyapal Date: April 3, 2009 Item: The cost of an 80-kW automotive polymer electrolyte membrane (PEM) fuel cell system operating on direct hydrogen and projected to a manufacturing volume of 500,000 units per year is $94/kW for 2007 technology in 2007 dollars ($82/kW in 2002 dollars for comparison with targets). Rationale: In fiscal year 2007, TIAX LLC (TIAX) and Directed Technologies, Inc. (DTI) each updated their 2006 cost analyses of direct hydrogen, 80-kW, PEM automotive fuel cell systems based on 2007 technology and projected to manufacturing volumes of 500,000 units per year [1,2].

87

DOE Hydrogen and Fuel Cells Program Record 9012: Fuel Cell System Cost - 2009  

NLE Websites -- All DOE Office Websites (Extended Search)

2 Date: October 7, 2009 2 Date: October 7, 2009 Title: Fuel Cell System Cost - 2009 Update to: Record 8019 Originator: Jacob Spendelow and Jason Marcinkoski Approved by: Sunita Satyapal Date: October 7, 2009 Item: The cost of an 80-kW automotive polymer electrolyte membrane (PEM) fuel cell system operating on direct hydrogen and projected to a manufacturing volume of 500,000 units per year is $61/kW for 2009 technology in 2009 dollars ($51/kW in 2002 dollars for comparison with targets). Rationale: In fiscal year 2009, TIAX LLC (TIAX) and Directed Technologies, Inc. (DTI) each updated their 2008 cost analyses of 80-kW direct hydrogen PEM automotive fuel cell systems based on 2009 technology and projected to manufacturing volumes of 500,000 units per year [1,2]. DTI and TIAX use Design for Manufacturing and Assembly

88

FUEL CYCLE COSTS IN A GRAPHITE MODERATED SLIGHTLY ENRICHED FUSED SALT REACTOR  

SciTech Connect

A fuel cycle economic study has been made for a 315Mwe graphite- moderated slightly enriched fused-salt reactor. Fuel cycle costs of less than 1.5 mills may be possible for such reactors operating on a ten-year cycle even when the fuel is discarded at the end of the cycle. Recovery of the uranium and plutonium at the end of the cycle reduces the fuel cycle costs to approximates 1 mill/kwh. Changes in the waste storage cost, reprocessing cost or salt inventory have a relatively minor effect on fuel cycle costs. (auth)

Guthrie, C.E.

1959-01-01T23:59:59.000Z

89

Fuel Cell Technologies Office: Wind-to-Hydrogen Cost Modeling and Project  

NLE Websites -- All DOE Office Websites (Extended Search)

Wind-to-Hydrogen Cost Wind-to-Hydrogen Cost Modeling and Project Findings (Text Version) to someone by E-mail Share Fuel Cell Technologies Office: Wind-to-Hydrogen Cost Modeling and Project Findings (Text Version) on Facebook Tweet about Fuel Cell Technologies Office: Wind-to-Hydrogen Cost Modeling and Project Findings (Text Version) on Twitter Bookmark Fuel Cell Technologies Office: Wind-to-Hydrogen Cost Modeling and Project Findings (Text Version) on Google Bookmark Fuel Cell Technologies Office: Wind-to-Hydrogen Cost Modeling and Project Findings (Text Version) on Delicious Rank Fuel Cell Technologies Office: Wind-to-Hydrogen Cost Modeling and Project Findings (Text Version) on Digg Find More places to share Fuel Cell Technologies Office: Wind-to-Hydrogen Cost Modeling and Project Findings (Text Version) on

90

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

Comparative Assessment of Fuel Cell Cars, Massachusettselectric and hydrogen fuel cell vehicles, Journal of PowerTransition to Hydrogen Fuel Cell Vehicles & the Potential

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

91

Market Cost of Renewable Jet Fuel Adoption in the United States  

E-Print Network (OSTI)

Market Cost of Renewable Jet Fuel Adoption in the United States Niven Winchester, Dominic Mc on recycled paper #12;1 Market Cost of Renewable Jet Fuel Adoption in the United States Niven Winchester Administration (FAA) has a goal that one billion gallons of renewable jet fuel is consumed by the US aviation

92

Optimization of labor allocation at a syringe production facility : design proposals  

E-Print Network (OSTI)

At MD Medical (Singapore), the syringe value stream is facing escalating labor cost and high labor turnover. Therefore, optimization of the current labor resources is necessary to control the labor cost effectively without ...

Su, Xiangyong

2008-01-01T23:59:59.000Z

93

Durable, Low-cost, Improved Fuel Cell Membranes  

Science Conference Proceedings (OSTI)

The development of low cost, durable membranes and membranes electrode assemblies (MEAs) that operate under reduced relative humidity (RH) conditions remain a critical challenge for the successful introduction of fuel cells into mass markets. It was the goal of the team lead by Arkema, Inc. to address these shortages. Thus, this project addresses the following technical barriers from the fuel cells section of the Hydrogen Fuel Cells and Infrastructure Technologies Program Multi-Year Research, Development and Demonstration Plan: (A) Durability (B) Cost Arkema’s approach consisted of using blends of polyvinylidenefluoride (PVDF) and proprietary sulfonated polyelectrolytes. In the traditional approach to polyelectrolytes for proton exchange membranes (PEM), all the required properties are “packaged” in one macromolecule. The properties of interest include proton conductivity, mechanical properties, durability, and water/gas transport. This is the case, for example, for perfluorosulfonic acid-containing (PFSA) membranes. However, the cost of these materials is high, largely due to the complexity and the number of steps involved in their synthesis. In addition, they suffer other shortcomings such as mediocre mechanical properties and insufficient durability for some applications. The strength and originality of Arkema’s approach lies in the decoupling of ion conductivity from the other requirements. Kynar® PVDF provides an exceptional combination of properties that make it ideally suited for a membrane matrix (Kynar® is a registered trademark of Arkema Inc.). It exhibits outstanding chemical resistance in highly oxidative and acidic environments. In work with a prior grant, a membrane known as M41 was developed by Arkema. M41 had many of the properties needed for a high performance PEM, but had a significant deficiency in conductivity at low RH. In the first phase of this work, the processing parameters of M41 were explored as a means to increase its proton conductivity. Optimizing the processing of M41 was found to increase its proton conductivity by almost an order of magnitude at 50% RH. Characterization of the membrane morphology with Karren More at Oak Ridge National Laboratory showed that the membrane morphology was complex. This technology platform was dubbed M43 and was used as a baseline in the majority of the work on the project. Although its performance was superior to M41, M43 still showed proton conductivity an order of magnitude lower than that of a PFSA membrane at 50% RH. The MEA performance of M43 could be increased by reducing the thickness from 1 to 0.6 mils. However, the performance of the thinner M43 still did not match that of a PFSA membrane.

Chris Roger; David Mountz; Wensheng He; Tao Zhang

2011-03-17T23:59:59.000Z

94

UW Madison Fleet Fiscal Year 2010 Rates: Fuel, maintenance and insurance costs are included. If fuel prices exceed the budgeted  

E-Print Network (OSTI)

UW Madison Fleet Fiscal Year 2010 Rates: Fuel, maintenance and insurance costs are included. If fuel prices exceed the budgeted amount by a significant margin, the rates will be amended with a fuel surcharge at that time and the change notice will be posted in the fleet web site, rates page. Some rate

Sheridan, Jennifer

95

Nuclear Fuel Cycle Cost Comparison Between Once-Through and Fully Closed Cycles  

Science Conference Proceedings (OSTI)

This report presents results from a parametric study of equilibrium fuel cycle costs for a closed fuel cycle with multi-recycling of plutonium (Pu) and minor actinides in fast reactors (FRs) compared to an open, once-through fuel cycle using pressurized water reactors (PWRs). The study examines the impact on fuel cycle costs from changes in the unit costs of uranium, advanced plutonium and uranium recovery by extraction (PUREX) reprocessing of discharged fast-reactor mixed-oxide (FR-MOX) fuel, and fabric...

2010-11-04T23:59:59.000Z

96

Dark spreads measure returns over fuel costs of coal-fired ...  

U.S. Energy Information Administration (EIA)

The dark spread is a common metric used to estimate returns over fuel costs of coal-fired electric generators. A dark spread is the difference between ...

97

Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems...  

NLE Websites -- All DOE Office Websites (Extended Search)

Mass Production Cost Estimation for Direct H 2 PEM Fuel Cell Systems for Automotive Applications: 2010 Update September 30, 2010 Prepared by: Brian D. James, Jeffrey A. Kalinoski...

98

Cost and Quality of Fuels for Electric Plants 2006 and 2007  

U.S. Energy Information Administration (EIA)

DOE/EIA-0191(2007) Distribution Category UC-950 Cost and Quality of Fuels for Electric Plants 2006 and 2007 December 2008 Energy Information Administration

99

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

change, and noise. Oil-use costs comprise the cost of theexcept as indicated) Oil-use cost SPR Low Best High BY ROCdirect economic costs of oil dependence – including wealth

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

100

Fuel Cell Technologies Office: DOE Announces New Hydrogen Cost...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Efficiency and Renewable Energy EERE Home | Programs & Offices | Consumer Information Fuel Cell Technologies Office Search Search Help Fuel Cell Technologies Office HOME ABOUT...

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Emission Control Cost-Effectiveness of Alternative-Fuel Vehicles  

E-Print Network (OSTI)

Effects of Compressed Natural Gas as a VehicleFuel-Volumepetroleumgas, compressed natural gas, and electricity.fuel vehicle types, compressed natural gas vehicles are the

Wang, Quanlu; Sperling, Daniel; Olmstead, Janis

1993-01-01T23:59:59.000Z

102

FUEL CELL SYSTEM ECONOMICS: COMPARING THE COSTS OF GENERATING POWER WITH STATIONARY  

E-Print Network (OSTI)

during many months of the year). * Similarly, use of PEM fuel cell waste heat for hot water heating wouldFUEL CELL SYSTEM ECONOMICS: COMPARING THE COSTS OF GENERATING POWER WITH STATIONARY AND MOTOR VEHICLE PEM FUEL CELL SYSTEMS UCD-ITS-RP-04-21 April 2004 by Timothy Lipman University of California

Kammen, Daniel M.

103

Transport Studies Enabling Efficiency Optimization of Cost-Competitive Fuel Cell Stacks  

NLE Websites -- All DOE Office Websites (Extended Search)

AURORA Program Overview Topic 4A. Transport within the PEM Stack / Transport Studies Transport Studies Enabling Efficiency Optimization of Cost-Competitive Fuel Cell Stacks Award#: DE-EE0000472 US DOE Fuel Cell Projects Kickoff Meeting Washington, DC September 30, 2009 Program Objectives The objective of this program is to optimize the efficiency of a stack technology meeting DOE cost targets. As cost reduction is of central importance in commercialization, the objective of this program addresses all fuel cell applications. AURORA C. Performance Technical Barriers Premise: DOE cost targets can be met by jointly exceeding both the Pt loading (1.0 W/cm2) targets.

104

Parametric Study of Front-End Nuclear Fuel Cycle Costs Using Reprocessed Uranium  

Science Conference Proceedings (OSTI)

This study evaluates front-end nuclear fuel cycle costs assuming that uranium recovered during the reprocessing of commercial light-water reactor (LWR) spent nuclear fuel is available to be recycled and used in the place of natural uranium. This report explores the relationship between the costs associated with using a natural uranium fuel cycle, in which reprocessed uranium (RepU) is not recycled, with those associated with using RepU.

2010-01-26T23:59:59.000Z

105

Low Cost PEM Fuel Cell Metal Bipolar Plates  

NLE Websites -- All DOE Office Websites (Extended Search)

Background and Mission 3 Project Objectives * Overall Objective: Develop lower cost metal bipolar plates to meet performance target and 2015 cost target (<3kW) - Develop...

106

Costs and benefits of automotive fuel economy improvement: A partial analysis  

SciTech Connect

This paper is an exercise in estimating the costs and benefits of technology-based fuel economy improvements for automobiles and light trucks. Benefits quantified include vehicle cots, fuel savings, consumer's surplus effects, the effect of reduced weight on vehicle safety, impacts on emissions of CO{sub 2} and criteria pollutants, world oil market and energy security benefits, and the transfer of wealth from US consumes to oil producers. A vehicle stock model is used to capture sales, scrappage, and vehicle use effects under three fuel price scenarios. Three alternative fuel economy levels for 2001 are considered, ranging from 32.9 to 36.5 MPG for cars and 24.2 to 27.5 MPG for light trucks. Fuel economy improvements of this size are probably cost-effective. The size of the benefit, and whether there is a benefit, strongly depends on the financial costs of fuel economy improvement and judgments about the values of energy security, emissions, safety, etc. Three sets of values for eight parameters are used to define the sensitivity of costs and benefits to key assumptions. The net present social value (1989$) of costs and benefits ranges from a cost of $11 billion to a benefit of $286 billion. The critical parameters being the discount rate (10% vs. 3%) and the values attached to externalities. The two largest components are always the direct vehicle costs and fuel savings, but these tend to counterbalance each other for the fuel economy levels examined here. Other components are the wealth transfer, oil cost savings, CO{sub 2} emissions reductions, and energy security benefits. Safety impacts, emissions of criteria pollutants, and consumer's surplus effects are relatively minor components. The critical issues for automotive fuel economy are therefore: (1) the value of present versus future costs and benefits, (2) the values of external costs and benefits, and (3) the financially cost-effective level of MPG achievable by available technology. 53 refs.

Greene, D.L. (Oak Ridge National Lab., TN (United States)); Duleep, K.G. (Energy and Environmental Analysis, Inc., Arlington, VA (United States))

1992-03-01T23:59:59.000Z

107

Costs and benefits of automotive fuel economy improvement: A partial analysis  

SciTech Connect

This paper is an exercise in estimating the costs and benefits of technology-based fuel economy improvements for automobiles and light trucks. Benefits quantified include vehicle cots, fuel savings, consumer`s surplus effects, the effect of reduced weight on vehicle safety, impacts on emissions of CO{sub 2} and criteria pollutants, world oil market and energy security benefits, and the transfer of wealth from US consumes to oil producers. A vehicle stock model is used to capture sales, scrappage, and vehicle use effects under three fuel price scenarios. Three alternative fuel economy levels for 2001 are considered, ranging from 32.9 to 36.5 MPG for cars and 24.2 to 27.5 MPG for light trucks. Fuel economy improvements of this size are probably cost-effective. The size of the benefit, and whether there is a benefit, strongly depends on the financial costs of fuel economy improvement and judgments about the values of energy security, emissions, safety, etc. Three sets of values for eight parameters are used to define the sensitivity of costs and benefits to key assumptions. The net present social value (1989$) of costs and benefits ranges from a cost of $11 billion to a benefit of $286 billion. The critical parameters being the discount rate (10% vs. 3%) and the values attached to externalities. The two largest components are always the direct vehicle costs and fuel savings, but these tend to counterbalance each other for the fuel economy levels examined here. Other components are the wealth transfer, oil cost savings, CO{sub 2} emissions reductions, and energy security benefits. Safety impacts, emissions of criteria pollutants, and consumer`s surplus effects are relatively minor components. The critical issues for automotive fuel economy are therefore: (1) the value of present versus future costs and benefits, (2) the values of external costs and benefits, and (3) the financially cost-effective level of MPG achievable by available technology. 53 refs.

Greene, D.L. [Oak Ridge National Lab., TN (United States); Duleep, K.G. [Energy and Environmental Analysis, Inc., Arlington, VA (United States)

1992-03-01T23:59:59.000Z

108

Costs and benefits of automotive fuel economy improvement: A partial analysis  

SciTech Connect

This paper is an exercise in estimating the costs and benefits of technology-based fuel economy improvements for automobiles and light trucks. Benefits quantified include vehicle cots, fuel savings, consumer's surplus effects, the effect of reduced weight on vehicle safety, impacts on emissions of CO{sub 2} and criteria pollutants, world oil market and energy security benefits, and the transfer of wealth from US consumes to oil producers. A vehicle stock model is used to capture sales, scrappage, and vehicle use effects under three fuel price scenarios. Three alternative fuel economy levels for 2001 are considered, ranging from 32.9 to 36.5 MPG for cars and 24.2 to 27.5 MPG for light trucks. Fuel economy improvements of this size are probably cost-effective. The size of the benefit, and whether there is a benefit, strongly depends on the financial costs of fuel economy improvement and judgments about the values of energy security, emissions, safety, etc. Three sets of values for eight parameters are used to define the sensitivity of costs and benefits to key assumptions. The net present social value (1989$) of costs and benefits ranges from a cost of $11 billion to a benefit of $286 billion. The critical parameters being the discount rate (10% vs. 3%) and the values attached to externalities. The two largest components are always the direct vehicle costs and fuel savings, but these tend to counterbalance each other for the fuel economy levels examined here. Other components are the wealth transfer, oil cost savings, CO{sub 2} emissions reductions, and energy security benefits. Safety impacts, emissions of criteria pollutants, and consumer's surplus effects are relatively minor components. The critical issues for automotive fuel economy are therefore: (1) the value of present versus future costs and benefits, (2) the values of external costs and benefits, and (3) the financially cost-effective level of MPG achievable by available technology. 53 refs.

Greene, D.L. (Oak Ridge National Lab., TN (United States)); Duleep, K.G. (Energy and Environmental Analysis, Inc., Arlington, VA (United States))

1992-03-01T23:59:59.000Z

109

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

analysis of battery electric, hydrogen fuel cell and hybrid vehicles in a future sustainable road transport system, Energy Policy

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

110

Challenge: Decrease Size and Cost of Fuel Processor  

E-Print Network (OSTI)

published papers 2 Patent Applications (mesoporous MOx, Pt/WO3 Fuel Cell Cat) #12;Significant Results

111

Study of costs associated with alternative fuels development: A case study. Research report  

SciTech Connect

The primary objective of the study was to conduct a case study of large-scale fuel conversion project to assess selected costs and related issues. An inventory of public transit agencies engaged in demonstration projects involving alternative fuels as conducted with representative sample of large public transit systems in the nation. Included in the survey were questions pertaining to fuel supply arrangements, fuel reserve storage requirements and/or deficiencies; future plans for managing energy resources and costs associated with fuel conversion/alternative fuels use -- whether planned or currently in operation. The case study approach was used to document the methodological and logistical problems encountered during the course of projects involving alternative fuels use compared with a control sample using diesel fuel. Monthly status reports on the alternative fuel project included data on accumulated mileage, road calls/unscheduled maintenance, fuel consumption, fuel cost per mile, alternative fuel purchases, schedule of activities, personnel, safety , and diesel emission test results. The data collected indicate several conclusions and future implications about technical and safety issues associated with the testing and use of liquefied natural gas (LNG).

Lede, N.W.

1995-07-01T23:59:59.000Z

112

Clean Cities Helps Nonprofit Cut Fuel Costs with Propane | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Clean Cities Helps Nonprofit Cut Fuel Costs with Propane Clean Cities Helps Nonprofit Cut Fuel Costs with Propane Clean Cities Helps Nonprofit Cut Fuel Costs with Propane May 15, 2013 - 4:10pm Addthis Mississippi's Community Counseling Services converted 29 vans to run on propane, saving more than $1.50 per gallon on fuel or more than $60,000 a year. | Photo courtesy of Community Counseling Services. Mississippi's Community Counseling Services converted 29 vans to run on propane, saving more than $1.50 per gallon on fuel or more than $60,000 a year. | Photo courtesy of Community Counseling Services. Shannon Brescher Shea Communications Manager, Clean Cities Program What are the key facts? Mississippi's Community Counseling Services converted 29 vans to run on propane, saving more than $1.50 per gallon on fuel or more than $60,000

113

Clean Cities Helps Nonprofit Cut Fuel Costs with Propane | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Helps Nonprofit Cut Fuel Costs with Propane Helps Nonprofit Cut Fuel Costs with Propane Clean Cities Helps Nonprofit Cut Fuel Costs with Propane May 15, 2013 - 4:10pm Addthis Mississippi's Community Counseling Services converted 29 vans to run on propane, saving more than $1.50 per gallon on fuel or more than $60,000 a year. | Photo courtesy of Community Counseling Services. Mississippi's Community Counseling Services converted 29 vans to run on propane, saving more than $1.50 per gallon on fuel or more than $60,000 a year. | Photo courtesy of Community Counseling Services. Shannon Brescher Shea Communications Manager, Clean Cities Program What are the key facts? Mississippi's Community Counseling Services converted 29 vans to run on propane, saving more than $1.50 per gallon on fuel or more than $60,000

114

Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems for Automotive Applications: 2007 Update  

Fuel Cell Technologies Publication and Product Library (EERE)

This report estimates fuel cell system cost for systems produced in the years 2007, 2010, and 2015, and is the first annual update of a comprehensive automotive fuel cell cost analysis.

115

Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems for Automotive Applications: 2008 Update  

Fuel Cell Technologies Publication and Product Library (EERE)

This report estimates fuel cell system cost for systems produced in the years 2006, 2010, and 2015, and is the second annual update of a comprehensive automotive fuel cell cost analysis.

116

Optimization of labor allocation at a syringe production facility : work study  

E-Print Network (OSTI)

At MD Company (Singapore), the syringe value stream faces escalating labor cost and high labor turnover. Two labor allocations were proposed previously to optimize current labor resources, with the aim of controlling the ...

Ng, Gar Yan

2008-01-01T23:59:59.000Z

117

Low Cost PEM Fuel Cell Metal Bipolar Plates  

E-Print Network (OSTI)

Objectives · Overall Objective: Develop lower cost metal bipolar plates to meet performance target and 2015 cost target (usage Electrical Conductivity S /cm >100 >100 Resistivity ohm.cm 25

118

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

Compressed Natural Gas (CNG), synthetic diesel, methanol,FCX Fuels Gasoline, Diesel, CNG, FT diesel, methanol, H2,H2, electricity Gasoline, diesel, CNG, biogas, LPG, ethanol,

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

119

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

analysis shows that hybrid and electric cars perform bettercar (4-5 passengers) Fuels Gasoline, CNG, diesel, FT50, methanol, H2 Powertrains ICE, hybrid,

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

120

Improving Costs and Efficiency of PEM Fuel Cell Vehicles by ...  

Fuel cell vehicles have the potential to reduce our dependence on foreign oil and lower emissions. Running the vehicle’s motor on hydrogen rather than gasoline ...

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Effect of changes in DOE pricing policies for enrichment and reprocessing on research reactor fuel cycle costs  

SciTech Connect

Fuel cycle costs with HEU and LEU fuels for the IAEA generic 10 MW reactor are updated to reflect the change in DOE pricing policy for enrichment services as of October 1985 and the published charges for LEU reprocessing services as of February 1986. The net effects are essentially no change in HEU fuel cycle costs and a reduction of about 8 to 10% in the fuel cycle costs for LEU silicide fuel.

Matos, J.E.; Freese, K.E.

1986-11-03T23:59:59.000Z

122

Low-Cost Manufacturing of Fuel Cell Bipolar Plates by ...  

Science Conference Proceedings (OSTI)

About this Abstract. Meeting, Materials Science & Technology 2009. Symposium, Emerging Material Forming Technologies. Presentation Title, Low-Cost ...

123

Analysis of near-term spent fuel transportation hardware requirements and transportation costs  

SciTech Connect

A computer model was developed to quantify the transportation hardware requirements and transportation costs associated with shipping spent fuel in the commercial nucler fuel cycle in the near future. Results from this study indicate that alternative spent fuel shipping systems (consolidated or disassembled fuel elements and new casks designed for older fuel) will significantly reduce the transportation hardware requirements and costs for shipping spent fuel in the commercial nuclear fuel cycle, if there is no significant change in their operating/handling characteristics. It was also found that a more modest cost reduction results from increasing the fraction of spent fuel shipped by truck from 25% to 50%. Larger transportation cost reductions could be realized with further increases in the truck shipping fraction. Using the given set of assumptions, it was found that the existing spent fuel cask fleet size is generally adequate to perform the needed transportation services until a fuel reprocessing plant (FRP) begins to receive fuel (assumed in 1987). Once the FRP opens, up to 7 additional truck systems and 16 additional rail systems are required at the reference truck shipping fraction of 25%. For the 50% truck shipping fraction, 17 additional truck systems and 9 additional rail systems are required. If consolidated fuel only is shipped (25% by truck), 5 additional rail casks are required and the current truck cask fleet is more than adequate until at least 1995. Changes in assumptions could affect the results. Transportation costs for a federal interim storage program could total about $25M if the FRP begins receiving fuel in 1987 or about $95M if the FRP is delayed until 1989. This is due to an increased utilization of federal interim storage facility from 350 MTU for the reference scenario to about 750 MTU if reprocessing is delayed by two years.

Daling, P.M.; Engel, R.L.

1983-01-01T23:59:59.000Z

124

Economic Analysis on Direct Use of Spent Pressurized Water Reactor Fuel in CANDU Reactors - III: Spent DUPIC Fuel Disposal Cost  

Science Conference Proceedings (OSTI)

The disposal costs of spent pressurized water reactor (PWR), Canada deuterium uranium (CANDU) reactor, and DUPIC fuels have been estimated based on available literature data and the engineering design of a spent CANDU fuel disposal facility by the Atomic Energy of Canada Limited. The cost estimation was carried out by the normalization concept of total electricity generation. Therefore, the future electricity generation scale was analyzed to evaluate the appropriate capacity of the high-level waste disposal facility in Korea, which is a key parameter of the disposal cost estimation. Based on the total electricity generation scale, it is concluded that the disposal unit costs for spent CANDU natural uranium, CANDU-DUPIC, and PWR fuels are 192.3, 388.5, and 696.5 $/kg heavy element, respectively.

Ko, Won Il; Choi, Hangbok; Roh, Gyuhong; Yang, Myung Seung [Korea Atomic Energy Research Institute (Korea, Republic of)

2001-05-15T23:59:59.000Z

125

Cost and quality of fuels for electric utility plants: Energy data report. 1980 annual  

SciTech Connect

In 1980 US electric utilities reported purchasng 594 million tons of coal, 408.5 million barrels of oil and 3568.7 billion ft/sup 3/ of gas. As compared with 1979 purchases, coal rose 6.7%, oil decreased 20.9%, and gas increased for the fourth year in a row. This volume presents tabulated and graphic data on the cost and quality of fossil fuel receipts to US electric utilities plants with a combined capacity of 25 MW or greater. Information is included on fuel origin and destination, fuel types, and sulfur content, plant types, capacity, and flue gas desulfurization method used, and fuel costs. (LCL)

1981-06-25T23:59:59.000Z

126

Optimal fuel cell system design considering functional performance and production costs  

E-Print Network (OSTI)

In this work the optimization-based, integrated concurrent design method is applied to the modelling, analysis, and design of a transportation fuel cell system. A general optimal design model considering both functional performance and production costs is first introduced. Using the Ballard Mark V Transit Bus fuel cell system as an example, the study explores the intrinsic relations among various fuel cell system performance and cost aspects to provide insights for new cost-effective designs. A joint performance and cost optimization is carried out to demonstrate this new approach. This approach breaks the traditional barrier between design Žconcerning functional performance. and manufacturing Ž concerning production costs., allowing both functional performance and production costs to

D. Xue A; Z. Dong B

1998-01-01T23:59:59.000Z

127

Intimate Labors  

E-Print Network (OSTI)

TOTAL PROJECT COSTS:OTHER COSTS F. TOTAL PROJECT DIRECT COSTS G. INDIRECT COSTS:Dean UCHRI TOTAL H. TOTAL PROJECT DIRECT & INDIRECT COSTS

2008-01-01T23:59:59.000Z

128

FUEL CONSUMPTION AND COST SAVINGS OF CLASS 8 HEAVY-DUTY TRUCKS POWERED BY NATURAL GAS  

Science Conference Proceedings (OSTI)

We compare the fuel consumption and greenhouse gas emissions of natural gas and diesel heavy-duty (HD) class 8 trucks under consistent simulated drive cycle conditions. Our study included both conventional and hybrid HD trucks operating with either natural gas or diesel engines, and we compare the resulting simulated fuel efficiencies, fuel costs, and payback periods. While trucks powered by natural gas engines have lower fuel economy, their CO2 emissions and costs are lower than comparable diesel trucks. Both diesel and natural gas powered hybrid trucks have significantly improved fuel economy, reasonable cost savings and payback time, and lower CO2 emissions under city driving conditions. However, under freeway-dominant driving conditions, the overall benefits of hybridization are considerably less. Based on payback period alone, non-hybrid natural gas trucks appear to be the most economic option for both urban and freeway driving environments.

Gao, Zhiming [ORNL; LaClair, Tim J [ORNL; Daw, C Stuart [ORNL; Smith, David E [ORNL

2013-01-01T23:59:59.000Z

129

Market Cost of Renewable Jet Fuel Adoption in the United States  

E-Print Network (OSTI)

The US Federal Aviation Administration (FAA) has a goal that one billion gallons of renewable jet fuel is consumed by the US aviation industry each year from 2018. We examine the cost to US airlines of meeting this goal ...

Winchester, N.

130

Cost Analysis of PEM Fuel Cell Systems for Transportation: September 30, 2005  

DOE Green Energy (OSTI)

The results of sensitivity and Monte Carlo analyses on PEM fuel cell components and the overall system are presented including the most important cost factors and the effects of selected scenarios.

Carlson, E. J.; Kopf, P.; Sinha, J.; Sriramulu, S.; Yang, Y.

2005-12-01T23:59:59.000Z

131

Impacts of Renewable Generation on Fossil Fuel Unit Cycling: Costs and Emissions (Presentation)  

Science Conference Proceedings (OSTI)

Prepared for the Clean Energy Regulatory Forum III, this presentation looks at the Western Wind and Solar Integration Study and reexamines the cost and emissions impacts of fossil fuel unit cycling.

Brinkman, G.; Lew, D.; Denholm, P.

2012-09-01T23:59:59.000Z

132

Low Cost High-H2 Syngas Production for Power and Liquid Fuels  

NLE Websites -- All DOE Office Websites (Extended Search)

Low Cost High-H2 Syngas Production for Power and Liquid Fuels Gas Technology Institute (GTI) Project Number: FE0011958 Project Description Proof-of-concept of a metal-polymeric...

133

DOE Hydrogen and Fuel Cells Program Record 12021: Cost Projections...  

NLE Websites -- All DOE Office Websites (Extended Search)

Approved by: Sunita Satyapal and Rick Farmer Date: November 28, 2012 Item: Delivery costs associated with distributed production refueling station functions, Compression,...

134

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

from U.S. consumers to foreign oil producers (a cost only inThus, the PS received by foreign oil producers is a real

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

135

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

Use of Persian-Gulf Oil for Motor Vehicles, Energy Policythe Use of Persian Gulf Oil for Motor Vehicles, UCD-ITS-RR-per gallon of motor fuel, Defense of oil on average; thus,

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

136

DOE Hydrogen and Fuel Cells Program Record 12001: H2 Production and Delivery Cost Apportionment  

NLE Websites -- All DOE Office Websites (Extended Search)

01 Date: May 14, 2012 01 Date: May 14, 2012 Title: H 2 Production and Delivery Cost Apportionment Originator: Scott Weil, Sara Dillich, Fred Joseck, and Mark Ruth Approved by: Sunita Satyapal and Rick Farmer Date: December 14, 2012 Item: The hydrogen threshold cost is defined as the untaxed cost of hydrogen (H 2 ) (produced, delivered, and dispensed) at which hydrogen fuel cell electric vehicles (FCEVs) are projected to become competitive on a $/mile basis with competing vehicles [gasoline in hybrid-electric vehicles (HEVs)] in 2020. As established in Record 11007 [1], this cost ranges from $2.00-$4.00/gge a of H 2 (based on $2007). The threshold cost can be apportioned into its constituent H 2 production and delivery costs, which can then serve as the respective cost targets for multi-year planning of the Fuel Cell Technologies (FCT)

137

Nuclear Fuel Recycling - the Value of the Separated Transuranics and the Levelized Cost of Electricity  

E-Print Network (OSTI)

We analyze the levelized cost of electricity (LCOE) for three different fuel cycles: a Once-Through Cycle, in which the spent fuel is sent for disposal after one use in a reactor, a Twice-Through Cycle, in which the spent ...

Parsons, John E.

138

Nuclear Fuel Cycle Cost Comparison Between Once-Through and Plutonium Multi-Recycling in Fast Reactors  

Science Conference Proceedings (OSTI)

This report presents results from a parametric study of equilibrium fuel cycle costs for a closed fuel cycle with multi-recycling of plutonium in fast reactors (FRs) compared to an open, once-through fuel cycle using PWRs. The study examines the impact on fuel cycle costs from changes in the unit costs of uranium, advanced PUREX reprocessing of discharged uranium dioxide (UO2) fuel and fast-reactor mixed-oxide (FR-MOX) fuel, and FR-MOX fuel fabrication. In addition, the impact associated with changes in ...

2010-03-15T23:59:59.000Z

139

Fuel cycle cost, reactor physics and fuel manufacturing considerations for Erbia-bearing PWR fuel with > 5 wt% U-235 content  

Science Conference Proceedings (OSTI)

The efforts to reduce fuel cycle cost have driven LWR fuel close to the licensed limit in fuel fissile content, 5.0 wt% U-235 enrichment, and the acceptable duty on current Zr-based cladding. An increase in the fuel enrichment beyond the 5 wt% limit, while certainly possible, entails costly investment in infrastructure and licensing. As a possible way to offset some of these costs, the addition of small amounts of Erbia to the UO{sub 2} powder with >5 wt% U-235 has been proposed, so that its initial reactivity is reduced to that of licensed fuel and most modifications to the existing facilities and equipment could be avoided. This paper discusses the potentialities of such a fuel on the US market from a vendor's perspective. An analysis of the in-core behavior and fuel cycle performance of a typical 4-loop PWR with 18 and 24-month operating cycles has been conducted, with the aim of quantifying the potential economic advantage and other operational benefits of this concept. Subsequently, the implications on fuel manufacturing and storage are discussed. While this concept has certainly good potential, a compelling case for its short-term introduction as PWR fuel for the US market could not be determined. (authors)

Franceschini, F.; Lahoda, E. J.; Kucukboyaci, V. N. [Westinghouse Electric Co. LLC, 1000 Westinghouse Drive, Cranberry Township, PA 16066 (United States)

2012-07-01T23:59:59.000Z

140

Preliminary assessment of costs and risks of transporting spent fuel by barge  

SciTech Connect

The purpose of this study is to analyze the costs and risks associated with transporting spent fuel by barge. The barge movements would be made in combination with rail movements to transport spent fuel from plants to a repository. For the purpose of this analysis, three candidate repository sites are analyzed: Yucca Mountain, Nevada, Deaf Smith, Texas, and Hanford, Washington. This report complements a report prepared by Sandia National Laboratories in 1984 that analyzes the costs and risks of transporting spent fuel by rail and by truck to nine candidate repository sites.

Tobin, R.L.; Meshkov, N.K.; Jones, R.H.

1985-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

DOE Hydrogen and Fuel Cells Program Record 5035: Cost Analysis...  

NLE Websites -- All DOE Office Websites (Extended Search)

5 Date: May 22, 2006 Title: Cost Analysis of Hydrogen Production from Natural Gas 2003 - 2005 Originator: Patrick Davis Approved by: JoAnn Milliken Approval Date: May 22, 2006 Item...

142

Societal lifetime cost of hydrogen fuel cell vehicles  

E-Print Network (OSTI)

cost $2,458, or $11.1/kWh. Carbon fiber was the major costrange of $10-$17/kWh and carbon fiber contributes about 65%

Sun, Yongling; Ogden, J; Delucchi, Mark

2010-01-01T23:59:59.000Z

143

Emission Control Cost-Effectiveness of Alternative-Fuel Vehicles  

E-Print Network (OSTI)

Kwh/mile) d Total Battery Capacity (Kwh) Cost per Battery (this study. in Total battery capacity was calculated as:calculated as total battery capacity multiplied by per-unit-

Wang, Quanlu; Sperling, Daniel; Olmstead, Janis

1993-01-01T23:59:59.000Z

144

On the Path to Low Cost Renewable Fuels, an Important Breakthrough |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

On the Path to Low Cost Renewable Fuels, an Important Breakthrough On the Path to Low Cost Renewable Fuels, an Important Breakthrough On the Path to Low Cost Renewable Fuels, an Important Breakthrough April 18, 2013 - 4:10pm Addthis NREL Scientist Bryon Donohoe looks at different views of ultra structures of pre-treated biomass materials in the Cellular Visualization room of the Biomass Surface Characterization Lab. | Photo by Dennis Schroeder, NREL. NREL Scientist Bryon Donohoe looks at different views of ultra structures of pre-treated biomass materials in the Cellular Visualization room of the Biomass Surface Characterization Lab. | Photo by Dennis Schroeder, NREL. A researcher examines a strain of the fermentation microorganism Zymomonas mobilis on a culture plate. NREL has genetically engineered and patented its own strains of Zymomonas mobilis to more effectively ferment the multiple sugars found in biomass as part of the cellulosic ethanol-to-renewable fuel conversion process. | Photo by Dennis Schroeder, NREL.

145

Materials and Modules for Low Cost, High Performance Fuel Cell Humidifiers  

NLE Websites -- All DOE Office Websites (Extended Search)

Kick-off Meeting, Kick-off Meeting, Wash. D.C - 10/01/2009 Materials and Modules for Low Cost, High Performance Fuel Cell Humidifiers Prime Contractor: W. L. Gore & Associates Elkton, MD Principal Investigator: William B. Johnson Sub-Contractor: dPoint Technologies Vancouver, BC W. L. Gore & Associates, Inc. DOE Kick-off Meeting, Wash. D.C - 10/01/2009 Ahluwalia, et. al, ibid. Mirza, Z. DOE Hydrogen Program Review, June 9-13, 2008; Washington, DC Background W. L. Gore & Associates, Inc. DOE Kick-off Meeting, Wash. D.C - 10/01/2009 Objective and Technical Barriers Addressed More efficient, low-cost humidifiers can increase fuel cell inlet humidity: Reduce system cost and size of balance of plant; Improve fuel cell performance; Improve fuel cell durability. OBJECTIVE: Demonstrate a durable, high performance water

146

Emission Control Cost-Effectiveness of Alternative-Fuel Vehicles  

E-Print Network (OSTI)

r---1 DF LPG M85 FFV J E85 FFV M100 FFV S/ton (Thousands)Vehicles MI00 DedL Vehicles E85 FFVs LPGVs Dual-Fuel CNGVsM85 Dedi. M1 00 DF LPG M85 FFV E85 FFV M100 FFV S/ton 3O (

Wang, Quanlu; Sperling, Daniel; Olmstead, Janis

1993-01-01T23:59:59.000Z

147

Cost and Performance Comparison Of Stationary Hydrogen Fueling Appliances  

E-Print Network (OSTI)

or nitrogen from air and the purification of hydrogen from sources such as catalytic reformer off gas, coke oven gas, and ethylene plant effluent gas. Pressure swing systems are based on selective adsorbent beds of hydrogen from natural gas to fuel hydrogen FCV's. Four potential reforming systems were studied: 10

148

A model of the Capital Cost of a natural gas-fired fuel cell based Central Utilities Plant  

DOE Green Energy (OSTI)

This model defines the methods used to estimate the cost associated with acquisition and installation of capital equipment of the fuel cell systems defined by the central utility plant model. The capital cost model estimates the cost of acquiring and installing the fuel cell unit, and all auxiliary equipment such as a boiler, air conditioning, hot water storage, and pumps. The model provides a means to adjust initial cost estimates to consider learning associated with the projected level of production and installation of fuel cell systems. The capital cost estimate is an input to the cost of ownership analysis where it is combined with operating cost and revenue model estimates.

Not Available

1993-06-30T23:59:59.000Z

149

Assessment of costs and benefits of flexible and alternative fuel use in the US transportation sector  

Science Conference Proceedings (OSTI)

In 1988 the Department of Energy (DOE) undertook a comprehensive technical analysis of a flexible-fuel transportation system in the United States. During the next two decades, alternative fuels such as alcohol (methanol or ethanol), compressed natural gas (CNG), and electricity could become practical alternatives to oil-based fuels in the US transportation sector. The DOE Alternative Fuels Assessment is aimed directly at questions of energy security and fuel availability. To keep interested parties informed about the progress of the DOE Alternative Fuels Assessment, the Department periodically publishes reports dealing with particular aspects of this complex study. This report provides an analysis of the expected costs to produce methanol from biomass feedstock.

Not Available

1990-12-01T23:59:59.000Z

150

Correlating Cycle Duty with Cost at Fossil Fuel Power Plants  

Science Conference Proceedings (OSTI)

The work described in this report is part of the ongoing EPRI Cycling Impacts Program to develop a range of analysis and simulation-capable planning tools. The objectives are to better determine cycling impacts (including incremental costs), reliability impact, component level effects, and impacts and other elements needed to better plan and manage operational and financial aspects of power generation. This report documents early efforts to establish strong correlations between the cycle duty of a produc...

2001-09-14T23:59:59.000Z

151

Comparative analysis of monetary estimates of external environmental costs associated with combustion of fossil fuels  

SciTech Connect

Public utility commissions in a number of states have begun to explicitly treat costs of environmental externalities in the resource planning and acquisition process (Cohen et al. 1990). This paper compares ten different estimates and regulatory determinations of external environmental costs associated with fossil fuel combustion, using consistent assumptions about combustion efficiency, emissions factors, and resource costs. This consistent comparison is useful because it makes explicit the effects of various assumptions. This paper uses the results of the comparison to illustrate pitfalls in calculation of external environmental costs, and to derive lessons for design of policies to incorporate these externalities into resource planning. 38 refs., 2 figs., 10 tabs.

Koomey, J.

1990-07-01T23:59:59.000Z

152

How to utilize hedging and a fuel surcharge program to stabilize the cost of fuel.  

E-Print Network (OSTI)

??This paper looks at some of these travails as well as the common tools used to approach a volatile priced commodity, diesel fuel. It focuses… (more)

Witalec, Michael R

2010-01-01T23:59:59.000Z

153

REDUCING ULTRA-CLEAN TRANSPORTATION FUEL COSTS WITH HYMELT HYDROGEN  

DOE Green Energy (OSTI)

Phase I of the work to be done under this agreement consisted of conducting atmospheric gasification of coal using the HyMelt technology to produce separate hydrogen rich and carbon monoxide rich product streams. In addition smaller quantities of petroleum coke and a low value refinery stream were gasified. Phase II of the work to be done under this agreement, consists of gasification of the above-mentioned feeds at a gasifier pressure of approximately 5 bar. The results of this work will be used to evaluate the technical and economic aspects of producing ultra-clean transportation fuels using the HyMelt technology in existing and proposed refinery configurations. This report describes activities for the ninth quarter of work performed under this agreement. The design of the vessel for pressure testing has been completed. The design will be finalized and purchased in the next quarter.

Donald P. Malone; William R. Renner

2005-07-01T23:59:59.000Z

154

Transportation costs for new fuel forms produced from low rank US coals  

DOE Green Energy (OSTI)

Transportation costs are examined for four types of new fuel forms (solid, syncrude, methanol, and slurry) produced from low rank coals found in the lower 48 states of the USA. Nine low rank coal deposits are considered as possible feedstocks for mine mouth processing plants. Transportation modes analyzed include ship/barge, pipelines, rail, and truck. The largest potential market for the new fuel forms is coal-fired utility boilers without emission controls. Lowest cost routes from each of the nine source regions to supply this market are determined. 12 figs.

Newcombe, R.J.; McKelvey, D.G. (TMS, Inc., Germantown, MD (USA)); Ruether, J.A. (USDOE Pittsburgh Energy Technology Center, PA (USA))

1990-09-01T23:59:59.000Z

155

Mass Production Cost Estimation For Direct H2 PEM Fuel Cell Systesm for Automotive Applications: 2010 Update  

Fuel Cell Technologies Publication and Product Library (EERE)

This report is the fourth annual update of a comprehensive automotive fuel cell cost analysis. It contains estimates for material and manufacturing costs of complete 80 kWnet direct?hydrogen proton ex

156

Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems for Automotive Applications: 2009 Update  

Fuel Cell Technologies Publication and Product Library (EERE)

This report is the third annual update of a comprehensive automotive fuel cell cost analysis. It contains estimates for material and manufacturing cost of complete 80 kWnet direct hydrogen proton exch

157

REDUCING ULTRA-CLEAN TRANSPORTATION FUEL COSTS WITH HYMELT HYDROGEN  

DOE Green Energy (OSTI)

This report describes activities for the third quarter of work performed under this agreement. Atmospheric testing was conducted as scheduled on June 5 through June 13, 2003. The test results were encouraging, however, the rate of carbon dissolution was below expectations. Additional atmospheric testing is scheduled for the first week of September 2003. Phase I of the work to be done under this agreement consists of conducting atmospheric gasification of coal using the HyMelt technology to produce separate hydrogen rich and carbon monoxide rich product stream. In addition smaller quantities of petroleum coke and a low value refinery stream will be gasified. DOE and EnviRes will evaluate the results of this work to determine the feasibility and desirability of proceeding to Phase II of the work to be done under this agreement, which is gasification of the above-mentioned feeds at a gasifier pressure of approximately 5 bar. The results of this work will be used to evaluate the technical and economic aspects of producing ultra-clean transportation fuels using the HyMelt technology in existing and proposed refinery configurations.

Donald P. Malone; William R. Renner

2003-07-31T23:59:59.000Z

158

REDUCING ULTRA-CLEAN TRANSPORTATION FUEL COSTS WITH HYMELT HYDROGEN  

DOE Green Energy (OSTI)

This report describes activities for the seventh quarter of work performed under this agreement. We await approval from the Swedish pressure vessel board to allow us to proceed with the procurement of the vessel for super atmospheric testing. Phase I of the work to be done under this agreement consists of conducting atmospheric gasification of coal using the HyMelt technology to produce separate hydrogen rich and carbon monoxide rich product streams. In addition smaller quantities of petroleum coke and a low value refinery stream will be gasified. DOE and EnviRes will evaluate the results of this work to determine the feasibility and desirability of proceeding to Phase II of the work to be done under this agreement, which is gasification of the above-mentioned feeds at a gasifier pressure of approximately 5 bar. The results of this work will be used to evaluate the technical and economic aspects of producing ultra-clean transportation fuels using the HyMelt technology in existing and proposed refinery configurations.

Donald P. Malone; William R. Renner

2005-01-01T23:59:59.000Z

159

Low-Cost Composite Materials for Polymer Electrolyte Fuel Cell Bipolar Plates  

DOE Green Energy (OSTI)

Polymer electrolyte fuel cells (PEFCS) are under widespread development to produce electrical power for a variety of stationary and transportation applications. To date, the bipolar plate remains the most problematic and costly component of PEFC stacks (1). In addition to meeting cost constraints, bipolar plates must possess a host of other properties, the most important of which are listed in Table 1. The most commonly used material for single cell testing is machined graphite, which is expensive and costly to machine. The brittle nature of graphite also precludes the use of thin components for reducing stack size and weight, which is particularly important for transportation applications. Other stack designs consider the use of metal hardware such as stainless steel (2,3). But a number of disadvantages are associated with stainless steel, including high density, high cost of machining, and possible corrosion in the fuel cell environment. In light of these difficulties, much of the recent work on fuel cell bipolar plate materials has concentrated on graphite/polymer composites (4--8). Composite materials offer the potential advantages of lower cost, lower weight, and greater ease of manufacture than traditional graphite and metal plates. For instance, flow fields can be molded directly into these composites, thereby eliminating the costly and difficult machining step required for graphite or metal hardware.

Busick, D.N.; Wilson, M.S.

1998-11-01T23:59:59.000Z

160

A comparison of estimates of cost-effectiveness of alternative fuels and vehicles for reducing emissions  

DOE Green Energy (OSTI)

The cost-effectiveness ratio (CER) is a measure of the monetary value of resources expended to obtain reductions in emissions of air pollutants. The CER can lead to selection of the most effective sequence of pollution reduction options. Derived with different methodologies and technical assumptions, CER estimates for alternative fuel vehicles (AFVs) have varied widely among pervious studies. In one of several explanations of LCER differences, this report uses a consistent basis for fuel price to re-estimate CERs for AFVs in reduction of emissions of criteria pollutants, toxics, and greenhouse gases. The re-estimated CERs for a given fuel type have considerable differences due to non-fuel costs and emissions reductions, but the CERs do provide an ordinal sense of cost-effectiveness. The category with CER less than $5,000 per ton includes compressed natural gas and ed Petroleum gas vehicles; and E85 flexible-fueled vehicles (with fuel mixture of 85 percent cellulose-derived ethanol in gasoline). The E85 system would be much less attractive if corn-derived ethanol were used. The CER for E85 (corn-derived) is higher with higher values placed on the reduction of gas emissions. CER estimates are relative to conventional vehicles fueled with Phase 1 California reformulated gasoline (RFG). The California Phase 2 RFG program will be implemented before significant market penetration by AFVs. CERs could be substantially greater if they are calculated incremental to the Phase 2 RFG program. Regression analysis suggests that different assumptions across studies can sometimes have predictable effects on the CER estimate of a particular AFV type. The relative differences in cost and emissions reduction assumptions can be large, and the effect of these differences on the CER estimate is often not predictable. Decomposition of CERs suggests that methodological differences can make large contributions to CER differences among studies.

Hadder, G.R.

1995-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Stationery and Emerging Market Fuel Cell System Cost Analysis - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

1 1 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Kathya Mahadevan (Primary Contact), VinceContini, Matt Goshe, and Fritz Eubanks Battelle 505 King Avenue Columbus, OH 43201 Phone: (614) 424-3197 Email: mahadevank@battelle.org DOE Managers HQ: Jason Marcinkoski Phone: (202) 586-7466 Email: Jason.Marcinkoski@ee.doe.gov GO: Reg Tyler Phone: (720) 356-1805 Email: Reginald.Tyler@go.doe.gov Contract Number: DE-EE0005250/001 Project Start Date: September 30, 2011 Project End Date: Project continuation and direction determined annually by DOE Fiscal Year (FY) 2012 Objectives To assist the DOE in developing fuel cell systems for stationary and emerging markets by developing independent cost models and costs estimates for manufacture and

162

How to utilize hedging and a fuel surcharge program to stabilize the cost of fuel  

E-Print Network (OSTI)

This paper looks at some of these travails as well as the common tools used to approach a volatile priced commodity, diesel fuel. It focuses on the impacts of hedging for companies that are directly impacted through the ...

Shehadi, Charles A., III (Charles Anthony)

2010-01-01T23:59:59.000Z

163

Crude Glycerol as Cost-Effective Fuel for Combined Heat and Power to Replace Fossil Fuels, Final Technical Report  

SciTech Connect

The primary objectives of this work can be summed into two major categories. Firstly, the fundamentals of the combustion of glycerol (in both a refined and unrefined form) were to be investigated, with emphasis of the development of a system capable of reliably and repeatedly combusting glycerol as well as an analysis of the emissions produced during glycerol combustion. Focus was placed on quantifying common emissions in comparison to more traditional fuels and this work showed that the burner developed was able to completely combust glycerol within a relatively wide range of operating conditions. Additionally, focus was placed on examining specific emissions in more detail, namely interesting NOx emissions observed in initial trials, acrolein and other volatile organic emissions, and particulate and ash emissions. This work showed that the combustion of crude glycerol could result in significantly reduced NOx emissions as a function of the high fuel bound oxygen content within the glycerol fuel. It also showed that when burned properly, the combustion of crude glycerol did not result in excessive emissions of acrolein or any other VOC compared to the combustion from more traditional fuels. Lastly however, this work has shown that in any practical application in which glycerol is being burned, it will be necessary to explore ash mitigation techniques due to the very high particulate matter concentrations produced during glycerol combustion. These emissions are comparable to unfiltered coal combustion and are directly tied to the biodiesel production method. The second focus of this work was directed to developing a commercialization strategy for the use of glycerol as a fuel replacement. This strategy has identified a 30 month plan for the scaling up of the laboratory scale burner into a pre-pilot scale system. Additionally, financing options were explored and an assessment was made of the economics of replacing a traditional fuel (namely natural gas) with crude glycerol from biodiesel production. This analysis showed that the cost of replacing natural gas with crude glycerol requires a strong function of the market price per unit of energy for the traditional fuel. However, the economics can be improved through the inclusion of a federal tax credit for the use of a renewable fuel. The conclusion of this analysis also shows that the ideal customer for energy replacement via crude glycerol is biodiesel producers who are located in remote regions, where the cost of energy is higher and the cost of crude glycerol is lowest. Lastly, the commercialization strategy analyzed competing technologies, namely traditional natural gas and electric heaters, as well as competing glycerol burners, and concludes with a discussion of the requirements for a pilot demonstration.

William L. ROberts

2012-10-31T23:59:59.000Z

164

LOW COST MULTI-LAYER FABRICATION METHOD FOR SOLID OXIDE FUEL CELLS (SOFC)  

SciTech Connect

Under this program, Technology Management, Inc, is evaluating the economic advantages of a multi-pass printing process on the costs of fabricating planar solid oxide fuel cell stacks. The technique, still unproven technically, uses a ''green-field'' or build-up approach. Other more mature processes were considered to obtain some baseline assumptions. Based on this analysis, TMI has shown that multi-pass printing can offer substantial economic advantages over many existing fabrication processes and can reduce costs. By impacting overall production costs, the time is compressed to penetrate early low volume niche markets and more mature high-volume market applications.

Dr. Christopher E. Milliken; Dr. Robert C. Ruhl

2001-05-16T23:59:59.000Z

165

Cost and Quality of Fuels for Electric Utility Plants 2000 Tables  

Gasoline and Diesel Fuel Update (EIA)

0) 0) Distribution Category UC-950 Cost and Quality of Fuels for Electric Utility Plants 2000 Tables August 2001 Energy Information Administration Office of Coal, Nuclear, Electric and Alternate Fuels U.S. Department of Energy Washington DC 20585 This report was prepared by the Energy Information Administration, the independent statistical and analytical agency within the Department of Energy. The information contained herein should not be construed as advocating or reflecting any policy position of the Department of Energy or any other organization. Contacts The annual publication Cost and Quality of Fuels for Electric Utility Plants (C&Q) is no longer published by the EIA. The tables presented in this document are intended to replace that annual publication. Questions

166

The transition to hydrogen as a transportation fuel: Costs and infrastructure requirements  

DOE Green Energy (OSTI)

Hydrogen fuel, used in an internal combustion engine optimized for maximum efficiency and as part of a hybrid-electric vehicle, will give excellent performance and range with emissions below one-tenth the ultra-low emission vehicle standards being considered in California as Equivalent Zero Emission Vehicles. These vehicles can also be manufactured with increased but not excessive cost. Hydrogen-fueled engines have demonstrated indicated efficiencies of more than 50% under lean operation. Combining optimized engines and other advanced components, the overall vehicle efficiency should approach 40%, compared with 13% for a conventional vehicle in the urban driving cycle. The optimized engine-generator unit is the mechanical equivalent of the fuel cell but at a cost competitive with today`s engines. The increased efficiency of hybrid-electric vehicles now makes hydrogen fuel competitive with today`s conventional vehicles. Conservative analysis of the infrastructure options to support a transition to a hydrogen-fueled light-duty fleet indicates that hydrogen may be utilized at a total cost comparable to the 3.1 cents/km U.S. vehicle operators pay today while using conventional automobiles. Both on-site production by electrolysis or reforming of natural gas and liquid hydrogen distribution offer the possibility of a smooth transition by taking advantage of existing large-scale energy infrastructures. Eventually, renewable sources of electricity and scalable methods of making hydrogen will have lower costs than today. With a hybrid-electric propulsion system, the infrastructure to supply hydrogen and the vehicles to use it can be developed today and thus be in place when fuel cells become economical for vehicle use.

Schock, R.N.; Berry, G.D.; Ramback, G.D.; Smith, J.R.

1996-03-20T23:59:59.000Z

167

An Evaluation of the Total Cost of Ownership of Fuel Cell-Powered Material Handling Equipment  

NLE Websites -- All DOE Office Websites (Extended Search)

Evaluation of the Total Cost Evaluation of the Total Cost of Ownership of Fuel Cell- Powered Material Handling Equipment Todd Ramsden National Renewable Energy Laboratory Technical Report NREL/TP-5600-56408 April 2013 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 15013 Denver West Parkway Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 An Evaluation of the Total Cost of Ownership of Fuel Cell- Powered Material Handling Equipment Todd Ramsden National Renewable Energy Laboratory Prepared under Task No. HT12.8610 Technical Report NREL/TP-5600-56408

168

Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems for Automotive Application  

NLE Websites -- All DOE Office Websites (Extended Search)

Mass Production Cost Estimation for Direct H 2 PEM Fuel Cell Systems for Automotive Applications: 2008 Update March 26, 2009 v.30.2021.052209 Prepared by: Brian D. James & Jeffrey A. Kalinoski One Virginia Square 3601 Wilson Boulevard, Suite 650 Arlington, Virginia 22201 703-243-3383 Prepared for: Contract No. GS-10F-0099J to the U.S. Department of Energy Energy Efficiency and Renewable Energy Office Hydrogen, Fuel Cells & Infrastructure Technologies Program Foreword Energy security is fundamental to the mission of the U.S. Department of Energy (DOE) and hydrogen fuel cell vehicles have the potential to eliminate the need for oil in the transportation sector. Fuel cell vehicles can operate on hydrogen, which can be produced domestically, emitting less greenhouse gas and pollutants than

169

Optimization of labor allocation at a syringe production facility using computer simulation  

E-Print Network (OSTI)

Optimization of the current labor resources at a Singapore pharmaceutical company is necessary to control the labor cost effectively without affecting the production capacity. Two new labor allocations were proposed. They ...

Liaw, Sze Sen

2008-01-01T23:59:59.000Z

170

Low cost fuel cell diffusion layer configured for optimized anode water management  

DOE Patents (OSTI)

A fuel cell comprises a cathode gas diffusion layer, a cathode catalyst layer, an anode gas diffusion layer, an anode catalyst layer and an electrolyte. The diffusion resistance of the anode gas diffusion layer when operated with anode fuel is higher than the diffusion resistance of the cathode gas diffusion layer. The anode gas diffusion layer may comprise filler particles having in-plane platelet geometries and be made of lower cost materials and manufacturing processes than currently available commercial carbon fiber substrates. The diffusion resistance difference between the anode gas diffusion layer and the cathode gas diffusion layer may allow for passive water balance control.

Owejan, Jon P; Nicotera, Paul D; Mench, Matthew M; Evans, Robert E

2013-08-27T23:59:59.000Z

171

Cost of Adding E85 Fuel Capability to Existing Gasoline Stations: NREL Survey and Literature Search (Fact Sheet)  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Cost of Adding E85 Fueling Capability to Existing Gasoline Stations: Cost of Adding E85 Fueling Capability to Existing Gasoline Stations: NREL Survey and Literature Search The cost of purchasing and installing E85 fueling equip- ment varies widely, yet station owners need to have an idea of what to expect when budgeting or reviewing bids for this upgrade. The purpose of this document is to provide a framework for station owners to assess what a reason- able cost would be. This framework was developed by the National Renewable Energy Laboratory (NREL) by surveying actual costs for stations, conducting a literature search, not- ing the major cost-affecting variables, addressing anomalies in the survey, and projecting changes in future costs. The findings of NREL's survey and literature search are shown in the table below. This table divides the study's

172

Conversion and standardization of university reactor fuels using low-enrichment uranium - options and costs  

SciTech Connect

The highly-enriched uranium (HEU) fuel used in twenty United States university reactors can be viewed as contributing to the risk of theft or diversion of weapons-useable material. The US Nuclear Regulatory Commission has issued a policy statement expressing its concern and has published a proposed rule on limiting the use of HEU in NRC-licensed non-power reactors. The fuel options, functional impacts, licensing, and scheduling of conversion and standardization of these reactor fuels to use of low-enrichment uranium (LEU) have been assessed. The university reactors span a wide range in form and function, from medium-power intense neutron sources where HEU fuel may be required, to low-power training and research facilities where HEU fuel is unnecessary. Conversion provides an opportunity to standardize university reactor fuels and improve reactor utilization in some cases. The entire program is estimated to cost about $10 million and to last about five years. Planning for conversion and standardization is facilitated by the US Department of Energy. 20 refs., 1 tab.

Harris, D.R.; Matos, J.E.; Young, H.H.

1985-01-01T23:59:59.000Z

173

Cost Analysis of PEM Fuel Cell Systems for Transportation: September 30, 2005  

NLE Websites -- All DOE Office Websites (Extended Search)

Subcontract Report Subcontract Report Cost Analysis of PEM Fuel Cell NREL/SR-560-39104 Systems for Transportation December 2005 September 30, 2005 E.J. Carlson, P. Kopf, J. Sinha, S. Sriramulu, and Y. Yang TIAX LLC Cambridge, Massachusetts NREL is operated by Midwest Research Institute ● Battelle Contract No. DE-AC36-99-GO10337 Cost Analysis of PEM Fuel Cell Systems for Transportation September 30, 2005 E.J. Carlson, P. Kopf, J. Sinha, S. Sriramulu, and Y. Yang TIAX LLC Cambridge, Massachusetts NREL Technical Monitor: K. Wipke Prepared under Subcontract No. KACX-5-44452-01 Subcontract Report NREL/SR-560-39104 December 2005 National Renewable Energy Laboratory 1617 Cole Boulevard, Golden, Colorado 80401-3393 303-275-3000 * www.nrel.gov Operated for the U.S. Department of Energy

174

Cost and energy consumption estimates for the aluminum-air battery anode fuel cycle  

DOE Green Energy (OSTI)

At the request of DOE's Office of Energy Storage and Distribution (OESD), Pacific Northwest Laboratory (PNL) conducted a study to generate estimates of the energy use and costs associated with the aluminum anode fuel cycle of the aluminum-air (Al-air) battery. The results of this analysis indicate that the cost and energy consumption characteristics of the mechanically rechargeable Al-air battery system are not as attractive as some other electrically rechargeable electric vehicle battery systems being developed by OESD. However, there are distinct advantages to mechanically rechargeable batteries, which may make the Al-air battery (or other mechanically rechargeable batteries) attractive for other uses, such as stand-alone applications. Fuel cells, such as the proton exchange membrane (PEM), and advanced secondary batteries may be better suited to electric vehicle applications. 26 refs., 3 figs., 25 tabs.

Humphreys, K.K.; Brown, D.R.

1990-01-01T23:59:59.000Z

175

Fuel Cell Power Model Elucidates Life-Cycle Costs for Fuel Cell-Based Combined Heat, Hydrogen, and Power (CHHP) Production Systems (Fact Sheet)  

Science Conference Proceedings (OSTI)

This fact sheet describes NREL's accomplishments in accurately modeling costs for fuel cell-based combined heat, hydrogen, and power systems. Work was performed by NREL's Hydrogen Technologies and Systems Center.

Not Available

2010-11-01T23:59:59.000Z

176

DOE Hydrogen and Fuel Cells Program Record 5014: Electricity Price Effect on Electrolysis Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

5014 Date: December 15, 2005 5014 Date: December 15, 2005 Title: Electricity Price Effect on Electrolysis Cost Originator: Roxanne Garland Approved by: JoAnn Milliken Date: January 2, 2006 Item: Effect of Electricity Price on Distributed Hydrogen Production Cost (Assumes: 1500 GGE/day, electrolyzer at 76% efficiency, and capital cost of $250/kW) The graph is based on the 2010 target of a 1500 kg/day water electrolysis refueling station described on page 3-12 of the Hydrogen, Fuel Cells and Infrastructure Technologies Program Multi-Year Research, Development and Demonstration Plan, February 2005. The graph uses all the same assumptions associated with the target, except for electricity price: Reference: - 76% efficient electrolyzer - 75% system efficiency

177

Toward a Common Method of Cost Estimation for CO2 Capture and Storage at Fossil Fuel Power Plants  

Science Conference Proceedings (OSTI)

There are significant differences in the methods employed by various organizations to estimate the cost of carbon capture and storage (CCS) systems for fossil fuel power plants. Such differences often are not readily apparent in publicly reported CCS cost estimates. As a consequence, there is a significant degree of misunderstanding, confusion, and mis-representation of CCS cost information, especially among audiences not familiar with the details of CCS costing. Given the international importance ...

2013-03-18T23:59:59.000Z

178

Effect of Highly Enriched/Highly Burnt UO2 Fuels on Fuel Cycle Costs, Radiotoxicity, and Nuclear Design Parameters  

Science Conference Proceedings (OSTI)

Technical Paper / Advances in Nuclear Fuel Management - Increased Enrichment/High Burnup and Light Water Reactor Fuel Cycle Optimization

Robert Gregg; Andrew Worrall

179

Nuclear Fuel Cycle Cost Comparison Between Once-Through and Plutonium Single-Recycling in Pressurized Water Reactors  

Science Conference Proceedings (OSTI)

Within the context of long-term waste management and sustainable nuclear fuel supply, there continue to be discussions regarding whether the United States should consider recycling of light-water reactor (LWR) spent nuclear fuel (SNF) for the current fleet of U.S. LWRs. This report presents a parametric study of equilibrium fuel cycle costs for an open fuel cycle without plutonium recycling (once-through) and with plutonium recycling (single-recycling using mixed-oxide, or MOX, fuel), assuming an all-pre...

2009-02-25T23:59:59.000Z

180

Forest Products: Georgia-Pacific's Insulation Upgrade Leads to Reduced Fuel Costs and Increased Process Efficiency  

SciTech Connect

This Steam Challenge Case Study looks at how the company, by insulating steam lines and replacing steam traps, was able to reduce fuel costs, increase process efficiency, and improve plant safety.

Ericksen, E.

1999-01-25T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Assessment of costs and benefits of flexible and alternative fuel use in the US transportation sector  

DOE Green Energy (OSTI)

The Alternative Motor Fuels Act of 1988 (Public Law 100-494), Section 400EE, states that the Secretary of Energy ...shall study methanol plants, including the costs and practicability of such plants that are (A) capable of utilizing current domestic supplies of unutilized natural gas; (B) relocatable; or (C) suitable for natural gas to methanol conversion by natural gas distribution companies...'' The purpose of this report is to characterize unutilized gas within the lower 48 states and to perform an economic analysis of methanol plants required by the act. The approach with regard to unutilized lower 48 gas is to (1) compare the costs of converting such gas to methanol against the expected price of gasoline over the next 20 years, and (2) compare the economics of converting such gas to methanol against the economics of using the gas as a pipeline-transported fuel. This study concludes that remote gas and low-Btu gas generally cannot be converted to methanol at costs near the expected competitive value of gasoline because of the poor economies of scale of small methanol plants.

Not Available

1991-07-01T23:59:59.000Z

182

Cost probability analysis of reprocessing spent nuclear fuel in the US G.D. Recktenwald, M.R. Deinert  

E-Print Network (OSTI)

to the sustainability of nuclear power while others argue against them on economic, environmental and security groundsCost probability analysis of reprocessing spent nuclear fuel in the US G.D. Recktenwald, M P48 Keywords: Reprocessing Nuclear power Spent fuel The methods by which nuclear power's radioactive

Deinert, Mark

183

Case Study: Georgia-Pacific Reduces Outside Fuel Costs and Increases Process Efficiency with Insulation Upgrade Program  

E-Print Network (OSTI)

A Georgia-Pacific plywood plant located in Madison, Georgia recently decided to insulate their steam lines for energy conservation, improved process efficiency and personnel protection. The goal of the project was to eliminate dependency on purchased fuel. Georgia-Pacific realized immediate and significant results and reduced fuel cost by about one third over a one year period.

Jackson, D.

1997-04-01T23:59:59.000Z

184

A LOW COST AND HIGH QUALITY SOLID FUEL FROM BIOMASS AND COAL FINES  

SciTech Connect

Use of biomass wastes as fuels in existing boilers would reduce greenhouse gas emissions, SO2 and NOx emissions, while beneficially utilizing wastes. However, the use of biomass has been limited by its low energy content and density, high moisture content, inconsistent configuration and decay characteristics. If biomass is upgraded by conventional methods, the cost of the fuel becomes prohibitive. Altex has identified a process, called the Altex Fuel Pellet (AFP) process, that utilizes a mixture of biomass wastes, including municipal biosolids, and some coal fines, to produce a strong, high energy content, good burning and weather resistant fuel pellet, that is lower in cost than coal. This cost benefit is primarily derived from fees that are collected for accepting municipal biosolids. Besides low cost, the process is also flexible and can incorporate several biomass materials of interest The work reported on herein showed the technical and economic feasibility of the AFP process. Low-cost sawdust wood waste and light fractions of municipal wastes were selected as key biomass wastes to be combined with biosolids and coal fines to produce AFP pellets. The process combines steps of dewatering, pellet extrusion, drying and weatherizing. Prior to pilot-scale tests, bench-scale test equipment was used to produce limited quantities of pellets for characterization. These tests showed which pellet formulations had a high potential. Pilot-scale tests then showed that extremely robust pellets could be produced that have high energy content, good density and adequate weatherability. It was concluded that these pellets could be handled, stored and transported using equipment similar to that used for coal. Tests showed that AFP pellets have a high combustion rate when burned in a stoker type systems. While NOx emissions under stoker type firing conditions was high, a simple air staging approach reduced emissions to below that for coal. In pulverized-fuel-fired tests it was found that the ground pellets could be used as an effective NOx control agent for pulverized-coal-fired systems. NOx emissions reductions up to 63% were recorded, when using AFP as a NOx control agent. In addition to performance benefits, economic analyses showed the good economic benefits of AFP fuel. Using equipment manufacturer inputs, and reasonable values for biomass, biosolids and coal fines costs, it was determined that an AFP plant would have good profitability. For cases where biosolids contents were in the range of 50%, the after tax Internal Rates of Return were in the range of 40% to 50%. These are very attractive returns. Besides the baseline analysis for the various AFP formulations tested at pilot scale, sensitivity analysis showed the impact of important parameters on return. From results, it was clear that returns are excellent for a range of parameters that could be expected in practice. Importantly, these good returns are achieved even without incentives related to the emissions control benefits of biomass.

John T. Kelly; George Miller; Mehdi Namazian

2001-07-01T23:59:59.000Z

185

Stationary Fuel Cell System Cost Analysis - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report Brian D. James (Primary Contact), Andrew B. Spisak, Whitney G. Colella Strategic Analysis, Inc. 4075 Wilson Blvd. Suite 200 Arlington, VA 22203 Phone: (703) 778-7114 Email: bjames@sainc.com DOE Managers HQ: Jason Marcinkoski Phone: (202) 586-7466 Email: Jason.Marcinkoski@ee.doe.gov GO: Gregory Kleen Phone: (720) 356-1672 Email: Gregory.Kleen@go.doe.gov Technical Advisor Bryan Pivovar Phone: (303) 275-3809 Email: bryan.pivovar@nrel.gov Sub-Contract Number No: AGB-0-40628-01 under Prime Contract No. DE-AC36-08G028308 Project Start Date: July 8, 2010 Project End Date: September 7, 2012 Fiscal Year (FY) 2012 Objectives Perform Design for Manufacturing and Assembly * (DFMA ® ) cost analysis for low-temperature (LT)

186

DEVELOPMENT OF LOW-COST MANUFACTURING PROCESSES FOR PLANAR, MULTILAYER SOLID OXIDE FUEL CELL ELEMENTS  

DOE Green Energy (OSTI)

This report summarizes the results of a four-year project, entitled, ''Low-Cost Manufacturing Of Multilayer Ceramic Fuel Cells'', jointly funded by the U.S. Department of Energy, the State of Ohio, and by project participants. The project was led by NexTech Materials, Ltd., with subcontracting support provided by University of Missouri-Rolla, Michael A. Cobb & Co., Advanced Materials Technologies, Inc., Edison Materials Technology Center, Gas Technology Institute, Northwestern University, and The Ohio State University. Oak Ridge National Laboratory, though not formally a subcontractor on the program, supported the effort with separate DOE funding. The objective of the program was to develop advanced manufacturing technologies for making solid oxide fuel cell components that are more economical and reliable for a variety of applications. The program was carried out in three phases. In the Phase I effort, several manufacturing approaches were considered and subjected to detailed assessments of manufacturability and development risk. Estimated manufacturing costs for 5-kW stacks were in the range of $139/kW to $179/kW. The risk assessment identified a number of technical issues that would need to be considered during development. Phase II development work focused on development of planar solid oxide fuel cell elements, using a number of ceramic manufacturing methods, including tape casting, colloidal-spray deposition, screen printing, spin-coating, and sintering. Several processes were successfully established for fabrication of anode-supported, thin-film electrolyte cells, with performance levels at or near the state-of-the-art. The work in Phase III involved scale-up of cell manufacturing methods, development of non-destructive evaluation methods, and comprehensive electrical and electrochemical testing of solid oxide fuel cell materials and components.

Scott Swartz; Matthew Seabaugh; William Dawson; Harlan Anderson; Tim Armstrong; Michael Cobb; Kirby Meacham; James Stephan; Russell Bennett; Bob Remick; Chuck Sishtla; Scott Barnett; John Lannutti

2004-06-12T23:59:59.000Z

187

Fuel Cost Savings Through Computer Control of a Boiler Complex - - Two Case Histories  

E-Print Network (OSTI)

This paper discusses the growing need for energy efficiency in industry and describes a new, packaged approach to fuel optimization through direct digital control and accurate in-stack measurement of combustion products. Results are presented for a large pulp and paper mill complex in which multiple power boilers and turbine generators are controlled so as to meet the total energy demand of the mill at minimum cost. Also discussed are results from a second installation involving control of a combined bark and gas boiler, a gas package boiler and a turbine generator, including utility tie-line control.

Worthley, C. M.

1979-01-01T23:59:59.000Z

188

Hydrogen Refueling Infrastructure Cost Analysis - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

9 9 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Marc W. Melaina (Primary Contact), Michael Penev and Darlene Steward National Renewable Energy Laboratory (NREL) 15013 Denver West Parkway Golden, CO 80401 Phone: (303) 275-3836 Email: Marc.Melaina@nrel.gov DOE Manager HQ: Fred Joseck Phone: (202) 586-7932 Email: Fred.Joseck@hq.doe.gov Subcontractor: IDC Energy Insights, Framingham, MA Project Start Date: October 1, 2010 Project End Date: September 28, 2012 Fiscal Year (FY) 2012 Objectives Identify the capacity (kg/day) and capital costs * associated with "Early Commercial" hydrogen stations (defined below) Identify cost metrics for larger numbers of stations and * larger capacities Technical Barriers This project addresses the following technical barriers

189

Establishing a Cost Basis for Converting the High Flux Isotope Reactor from High Enriched to Low Enriched Uranium Fuel  

Science Conference Proceedings (OSTI)

Under the auspices of the Global Threat Reduction Initiative Reduced Enrichment for Research and Test Reactors Program, the National Nuclear Security Administration /Department of Energy (NNSA/DOE) has, as a goal, to convert research reactors worldwide from weapons grade to non-weapons grade uranium. The High Flux Isotope Reactor (HFIR) at Oak Ridge National Lab (ORNL) is one of the candidates for conversion of fuel from high enriched uranium (HEU) to low enriched uranium (LEU). A well documented business model, including tasks, costs, and schedules was developed to plan the conversion of HFIR. Using Microsoft Project, a detailed outline of the conversion program was established and consists of LEU fuel design activities, a fresh fuel shipping cask, improvements to the HFIR reactor building, and spent fuel operations. Current-value costs total $76 million dollars, include over 100 subtasks, and will take over 10 years to complete. The model and schedule follows the path of the fuel from receipt from fuel fabricator to delivery to spent fuel storage and illustrates the duration, start, and completion dates of each subtask to be completed. Assumptions that form the basis of the cost estimate have significant impact on cost and schedule.

Primm, Trent [ORNL; Guida, Tracey [University of Pittsburgh

2010-02-01T23:59:59.000Z

190

How refinery fuel indexes have varied  

Science Conference Proceedings (OSTI)

Refinery fuels costs have endured a steady incline since 1993, except for a period in 1993. As shown in the accompanying table, these increases in cost have occurred for residual fuel oil costs in three of the five PADD districts. The cost for natural gas for refinery usage also dropped steadily during the 3-year study. These conclusions are based on costs of an average refinery fuel consisting of 1 bbl each of PADD Districts 1--5 and an average US cost of 4.4 MMscf natural gas (a 1 bbl equivalent on a BTU content basis). Raw residual fuel oil and natural gas prices come from publications put out by the US Department of Labor.

Farrar, G.

1997-01-06T23:59:59.000Z

191

Modular, High-Volume Fuel Cell Leak-Test Suite and Process  

DOE Green Energy (OSTI)

Fuel cell stacks are typically hand-assembled and tested. As a result the manufacturing process is labor-intensive and time-consuming. The fluid leakage in fuel cell stacks may reduce fuel cell performance, damage fuel cell stack, or even cause fire and become a safety hazard. Leak check is a critical step in the fuel cell stack manufacturing. The fuel cell industry is in need of fuel cell leak-test processes and equipment that is automatic, robust, and high throughput. The equipment should reduce fuel cell manufacturing cost.

Ru Chen; Ian Kaye

2012-03-12T23:59:59.000Z

192

Labor Standards for Construction | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Labor Standards for Construction Labor Standards for Construction Labor Standards for Construction More Documents & Publications Chapter 22 - Labor Standards for Construction Labor...

193

Cost/performance comparison between pulse columns and centrifugal contactors designed to process Clinch River Breeder Reactor fuel  

Science Conference Proceedings (OSTI)

A comparison between pulse columns and centrifugal contactors was made to determine which type of equipment was more advantageous for use in the primary decontamination cycle of a remotely operated fuel reprocessing plant. Clinch River Breeder Reactor (CRBR) fuel was chosen as the fuel to be processed in the proposed 1 metric tonne/day reprocessing facility. The pulse columns and centrifugal contactors were compared on a performance and total cost basis. From this comparison, either the pulse columns or the centrifugal contactors will be recommended for use in a fuel reprocessing plant built to reprocess CRBR fuel. The reliability, solvent exposure to radiation, required time to reach steady state, and the total costs were the primary areas of concern for the comparison. The pulse column units were determined to be more reliable than the centrifugal contactors. When a centrifugal contactor motor fails, it can be remotely changed in less than one eight hour shift. Pulse columns expose the solvent to approximately five times as much radiation dose as the centrifugal contactor units; however, the proposed solvent recovery system adequately cleans the solvent for either case. The time required for pulse columns to reach steady state is many times longer than the time required for centrifugal contactors to reach steady state. The cost comparison between the two types of contacting equipment resulted in centrifugal contactors costing 85% of the total cost of pulse columns when the contactors were stacked on three levels in the module. If the centrifugal contactors were all positioned on the top level of a module with the unoccupied volume in the module occupied by other equipment, the centrifugal contactors cost is 66% of the total cost of pulse columns. Based on these results, centrifugal contactors are recommended for use in a remotely operated reprocessing plant built to reprocess CRBR fuel.

Ciucci, J.A. Jr.

1983-12-01T23:59:59.000Z

194

Projected Cost, Energy Use, and Emissions of Hydrogen Technologies for Fuel Cell Vehicles  

SciTech Connect

Each combination of technologies necessary to produce, deliver, and distribute hydrogen for transportation use has a corresponding levelized cost, energy requirement, and greenhouse gas emission profile depending upon the technologies' efficiencies and costs. Understanding the technical status, potential, and tradeoffs is necessary to properly allocate research and development (R&D) funding. In this paper, levelized delivered hydrogen costs, pathway energy use, and well-to-wheels (WTW) energy use and emissions are reported for multiple hydrogen production, delivery, and distribution pathways. Technologies analyzed include both central and distributed reforming of natural gas and electrolysis of water, and central hydrogen production from biomass and coal. Delivery options analyzed include trucks carrying liquid hydrogen and pipelines carrying gaseous hydrogen. Projected costs, energy use, and emissions for current technologies (technology that has been developed to at least the bench-scale, extrapolated to commercial-scale) are reported. Results compare favorably with those for gasoline, diesel, and E85 used in current internal combustion engine (ICE) vehicles, gasoline hybrid electric vehicles (HEVs), and flexible fuel vehicles. Sensitivities of pathway cost, pathway energy use, WTW energy use, and WTW emissions to important primary parameters were examined as an aid in understanding the benefits of various options. Sensitivity studies on production process energy efficiency, total production process capital investment, feed stock cost, production facility operating capacity, electricity grid mix, hydrogen vehicle market penetration, distance from the hydrogen production facility to city gate, and other parameters are reported. The Hydrogen Macro-System Model (MSM) was used for this analysis. The MSM estimates the cost, energy use, and emissions trade offs of various hydrogen production, delivery, and distribution pathways under consideration. The MSM links the H2A Production Model, the Hydrogen Delivery Scenario Analysis Model (HDSAM), and the Greenhouse Gas, Regulated Emission, and Energy for Transportation (GREET) Model. The MSM utilizes the capabilities of each component model and ensures the use of consistent parameters between the models to enable analysis of full hydrogen production, delivery, and distribution pathways. To better understand spatial aspects of hydrogen pathways, the MSM is linked to the Hydrogen Demand and Resource Analysis Tool (HyDRA). The MSM is available to the public and enables users to analyze the pathways and complete sensitivity analyses.

Ruth, M. F.; Diakov, V.; Laffen, M. J.; Timbario, T. A.

2010-01-01T23:59:59.000Z

195

DOE Hydrogen and Fuel Cells Program Record 12024: Hydrogen Production Cost Using Low-Cost Natural Gas  

NLE Websites -- All DOE Office Websites (Extended Search)

2024 Date: September 19, 2012 2024 Date: September 19, 2012 Title: Hydrogen Production Cost Using Low-Cost Natural Gas Originator: Sara Dillich, Todd Ramsden & Marc Melaina Approved by: Sunita Satyapal Date: September 24, 2012 Item: Hydrogen produced and dispensed in distributed facilities at high-volume refueling stations using current technology and DOE's Annual Energy Outlook (AEO) 2009 projected prices for industrial natural gas result in a hydrogen levelized cost of $4.49 per gallon-gasoline-equivalent (gge) (untaxed) including compression, storage and dispensing costs. The hydrogen production portion of this cost is $2.03/gge. In comparison, current analyses using low-cost natural gas with a price of $2.00 per MMBtu can decrease the hydrogen levelized cost to $3.68 per gge (untaxed) including

196

Transportation Energy Futures Series: Alternative Fuel Infrastructure Expansion: Costs, Resources, Production Capacity, and Retail Availability for Low-Carbon Scenarios  

DOE Green Energy (OSTI)

Achieving the Department of Energy target of an 80% reduction in greenhouse gas emissions by 2050 depends on transportation-related strategies combining technology innovation, market adoption, and changes in consumer behavior. This study examines expanding low-carbon transportation fuel infrastructure to achieve deep GHG emissions reductions, with an emphasis on fuel production facilities and retail components serving light-duty vehicles. Three distinct low-carbon fuel supply scenarios are examined: Portfolio: Successful deployment of a range of advanced vehicle and fuel technologies; Combustion: Market dominance by hybridized internal combustion engine vehicles fueled by advanced biofuels and natural gas; Electrification: Market dominance by electric drive vehicles in the LDV sector, including battery electric, plug-in hybrid, and fuel cell vehicles, that are fueled by low-carbon electricity and hydrogen. A range of possible low-carbon fuel demand outcomes are explored in terms of the scale and scope of infrastructure expansion requirements and evaluated based on fuel costs, energy resource utilization, fuel production infrastructure expansion, and retail infrastructure expansion for LDVs. This is one of a series of reports produced as a result of the Transportation Energy Futures (TEF) project, a Department of Energy-sponsored multi-agency project initiated to pinpoint underexplored transportation-related strategies for abating GHGs and reducing petroleum dependence.

Melaina, M. W.; Heath, G.; Sandor, D.; Steward, D.; Vimmerstedt, L.; Warner, E.; Webster, K. W.

2013-04-01T23:59:59.000Z

197

Spent fuel disassembly hardware and other non-fuel bearing components: characterization, disposal cost estimates, and proposed repository acceptance requirements  

SciTech Connect

There are two categories of waste considered in this report. The first is the spent fuel disassembly (SFD) hardware. This consists of the hardware remaining after the fuel pins have been removed from the fuel assembly. This includes end fittings, spacer grids, water rods (BWR) or guide tubes (PWR) as appropriate, and assorted springs, fasteners, etc. The second category is other non-fuel-bearing (NFB) components the DOE has agreed to accept for disposal, such as control rods, fuel channels, etc., under Appendix E of the standard utiltiy contract (10 CFR 961). It is estimated that there will be approximately 150 kg of SFD and NFB waste per average metric ton of uranium (MTU) of spent uranium. PWR fuel accounts for approximately two-thirds of the average spent-fuel mass but only 50 kg of the SFD and NFB waste, with most of that being spent fuel disassembly hardware. BWR fuel accounts for one-third of the average spent-fuel mass and the remaining 100 kg of the waste. The relatively large contribution of waste hardware in BWR fuel, will be non-fuel-bearing components, primarily consisting of the fuel channels. Chapters are devoted to a description of spent fuel disassembly hardware and non-fuel assembly components, characterization of activated components, disposal considerations (regulatory requirements, economic analysis, and projected annual waste quantities), and proposed acceptance requirements for spent fuel disassembly hardware and other non-fuel assembly components at a geologic repository. The economic analysis indicates that there is a large incentive for volume reduction.

Luksic, A.T.; McKee, R.W.; Daling, P.M.; Konzek, G.J.; Ludwick, J.D.; Purcell, W.L.

1986-10-01T23:59:59.000Z

198

The Guy at the Controls: Labor Quality and Power Plant Efficiency  

E-Print Network (OSTI)

Controls: Labor Quality and Power Plant Efficiency July 2007Controls: Labor Quality and Power Plant E ciency James B.on the fuel e ciency of power plants. Although electricity

Bushnell, Jim B; Wolfram, Catherine D

2007-01-01T23:59:59.000Z

199

Alternative Fuels Data Center  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Rhode Island Incentives and Laws Rhode Island Incentives and Laws The following is a list of expired, repealed, and archived incentives, laws, regulations, funding opportunities, or other initiatives related to alternative fuels and vehicles, advanced technologies, or air quality. Alternative Fuel Vehicle (AFV) Loans Expired: 04/10/2009 The Rhode Island Office of Energy Resources offers loans for up to five years, with low administrative fees, to state agencies and municipal governments to cover the incremental cost of purchasing original equipment manufactured AFVs. Alternative Fuel Vehicle (AFV) and Fueling Infrastructure Tax Credit Expired: 01/01/2008 The Alternative Fueled Vehicle and Filling Station Tax Credit entitles taxpayers to a tax credit equal to 50% of the capital, labor, and equipment

200

Mass-Production Cost Estimation for Automotive Fuel Cell Systems - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report Brian D. James (Primary Contact), Kevin Baum, Andrew B. Spisak, Whitney G. Colella Strategic Analysis, Inc. 4075 Wilson Blvd. Suite 200 Arlington VA 22203 Phone: (703) 778-7114 Email: bjames@sainc.com DOE Managers HQ: Jason Marcinkoski, Phone: (202) 586-7466 Email: Jason.Marcinkoski@ee.doe.gov GO: Gregory Kleen Phone: (720) 356-1672 Email: Gregory.Kleen@go.doe.gov Contract Number: DE-EE0005236 Project Start Date: September 30, 2011 Project End Date: September 30, 2016 Fiscal Year (FY) 2012 Objectives Update 2011 automotive fuel cell cost model to include * latest performance data and system design information. Examine costs of fuel cell systems (FCSs) for light-duty * vehicle and bus applications.

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

An Econometric Analysis of the Elasticity of Vehicle Travel with Respect to Fuel Cost per Mile Using RTEC Survey Data  

Science Conference Proceedings (OSTI)

This paper presents the results of econometric estimation of the ''rebound effect'' for household vehicle travel in the United States based on a comprehensive analysis of survey data collected by the U.S. Energy Information Administration (EIA) at approximately three-year intervals over a 15-year period. The rebound effect is defined as the percent change in vehicle travel for a percent change in fuel economy. It summarizes the tendency to ''take back'' potential energy savings due to fuel economy improvements in the form of increased vehicle travel. Separate vehicles use models were estimated for one-, two-, three-, four-, and five-vehicle households. The results are consistent with the consensus of recently published estimates based on national or state-level data, which show a long-run rebound effect of about +0.2 (a ten percent increase in fuel economy, all else equal, would produce roughly a two percent increase in vehicle travel and an eight percent reduction in fuel use). The hypothesis that vehicle travel responds equally to changes in fuel cost-per-mile whether caused by changes in fuel economy or fuel price per gallon could not be rejected. Recognizing the interdependency in survey data among miles of travel, fuel economy and price paid for fuel for a particular vehicle turns out to be crucial to obtaining meaningful results.

Greene, D.L.; Kahn, J.; Gibson, R.

1999-03-01T23:59:59.000Z

202

Critical analysis of the Hanford spent nuclear fuel project activity based cost estimate  

Science Conference Proceedings (OSTI)

In 1997, the SNFP developed a baseline change request (BCR) and submitted it to DOE-RL for approval. The schedule was formally evaluated to have a 19% probability of success [Williams, 1998]. In December 1997, DOE-RL Manager John Wagoner approved the BCR contingent upon a subsequent independent review of the new baseline. The SNFP took several actions during the first quarter of 1998 to prepare for the independent review. The project developed the Estimating Requirements and Implementation Guide [DESH, 1998] and trained cost account managers (CAMS) and other personnel involved in the estimating process in activity-based cost (ABC) estimating techniques. The SNFP then applied ABC estimating techniques to develop the basis for the December Baseline (DB) and documented that basis in Basis of Estimate (BOE) books. These BOEs were provided to DOE in April 1998. DOE commissioned Professional Analysis, Inc. (PAI) to perform a critical analysis (CA) of the DB. PAI`s review formally began on April 13. PAI performed the CA, provided three sets of findings to the SNFP contractor, and initiated reconciliation meetings. During the course of PAI`s review, DOE directed the SNFP to develop a new baseline with a higher probability of success. The contractor transmitted the new baseline, which is referred to as the High Probability Baseline (HPB), to DOE on April 15, 1998 [Williams, 1998]. The HPB was estimated to approach a 90% confidence level on the start of fuel movement [Williams, 1998]. This high probability resulted in an increased cost and a schedule extension. To implement the new baseline, the contractor initiated 26 BCRs with supporting BOES. PAI`s scope was revised on April 28 to add reviewing the HPB and the associated BCRs and BOES.

Warren, R.N.

1998-09-29T23:59:59.000Z

203

On-Board Vehicle, Cost Effective Hydrogen Enhancement Technology for Transportation PEM Fuel Cells  

DOE Green Energy (OSTI)

Final Report of On-Board Vehicle, Cost Effective Hydrogen Enhancement Technology for Transportation PEM Fuel Cells. The objective of this effort was to technologically enable a compact, fast start-up integrated Water Gas Shift-Pd membrane reactor for integration into an On Board Fuel Processing System (FPS) for an automotive 50 kWe PEM Fuel Cell (PEM FC). Our approach was to: (1) use physics based reactor and system level models to optimize the design through trade studies of the various system design and operating parameters; and (2) synthesize, characterize and assess the performance of advanced high flux, high selectivity, Pd alloy membranes on porous stainless steel tubes for mechanical strength and robustness. In parallel and not part of this program we were simultaneously developing air tolerant, high volumetric activity, thermally stable Water Gas Shift catalysts for the WGS/membrane reactor. We identified through our models the optimum WGS/membrane reactor configuration, and best Pd membrane/FPS and PEM FC integration scheme. Such a PEM FC power plant was shown through the models to offer 6% higher efficiency than a system without the integrated membrane reactor. The estimated FPS response time was < 1 minute to 50% power on start-up, 5 sec transient response time, 1140 W/L power density and 1100 W/kg specific power with an estimated production cost of $35/kW. Such an FPS system would have a Catalytic Partial Oxidation System (CPO) rather than the slower starting Auto-Thermal Reformer (ATR). We found that at optimum WGS reactor configuration that H{sub 2} recovery efficiencies of 95% could be achieved at 6 atm WGS pressure. However optimum overall fuel to net electrical efficiency ({approx}31%) is highest at lower fuel processor efficiency (67%) with 85% H{sub 2} recovery because less parasitic power is needed. The H{sub 2} permeance of {approx}45 m{sup 3}/m{sup 2}-hr-atm{sup 0.5} at 350 C was assumed in these simulations. In the laboratory we achieved a H{sub 2} permeance of 50 m{sup 3}/(m{sup 2}-hr-atm{sup 0.5}) with a H{sub 2}/N{sub 2} selectivity of 110 at 350 C with pure Pd. We also demonstrated that we could produce Pd-Ag membranes. Such alloy membranes are necessary because they aren't prone to the Pd-hydride {alpha}-{beta} phase transition that is known to cause membrane failure in cyclic operation. When funding was terminated we were on track to demonstrated Pd-Ag alloy deposition on a nano-porous ({approx}80 nm) oxide layer supported on porous stainless steel tubing using a process designed for scale-up.

Thomas H. Vanderspurt; Zissis Dardas; Ying She; Mallika Gummalla; Benoit Olsommer

2005-12-30T23:59:59.000Z

204

Fuel Cell Technologies Office: Fuel Cell Technical Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

Technical Publications Technical Publications Technical information about fuel cells published in technical reports, conference proceedings, journal articles, and Web sites is provided here. General Transportation Stationary/Distributed Power Auxiliary & Portable Power Manufacturing General Economic Impact of Fuel Cell Deployment in Forklifts and for Backup Power under the American Recovery and Reinvestment Act-This report by Argonne National Laboratory presents estimates of economic impacts associated with expenditures under the American Recovery and Reinvestment Act, also known as the Recovery Act, by the U.S. Department of Energy for the deployment of fuel cells in forklift and backup power applications. (April 2013). An Evaluation of the Total Cost of Ownership of Fuel Cell-Powered Material Handling Equipment-This report by the National Renewable Energy Laboratory discusses an analysis of the total cost of ownership of fuel cell-powered and traditional battery-powered material handling equipment, including the capital costs of battery and fuel cell systems, the cost of supporting infrastructure, maintenance costs, warehouse space costs, and labor costs. (April 2013).

205

DOE Hydrogen and Fuel Cells Program Record 9017: On-Board Hydrogen Storage Systems … Projected Performance and Cost Parameters  

NLE Websites -- All DOE Office Websites (Extended Search)

DOE Hydrogen and Fuel Cells Program Record DOE Hydrogen and Fuel Cells Program Record Record #: 9017 Date: July 02, 2010 Title: On-Board Hydrogen Storage Systems - Projected Performance and Cost Parameters Originators: Robert C. Bowman and Ned Stetson Approved by: Sunita Satyapal Date: August 10, 2010 This record summarizes the current technical assessments of hydrogen (H 2 ) storage system capacities and projected manufacturing costs for the scenario of high-volume production (i.e., 500,000 units/year) for various types of "on-board" vehicular storage systems. These analyses were performed within the Hydrogen Storage sub-program of the DOE Fuel Cell Technologies (FCT) program of the Office of Energy Efficiency and Renewable Energy. Item: It is important to note that all system capacities are "net useable capacities" able to be delivered to the

206

Long-run incremental costs and the pricing of electricity. Part II. [Comparative evaluation of marginal cost pricing and average cost pricing  

SciTech Connect

Total costs have essentially the same cost components whether long-run average costs or long-run incremental costs are used. The variable components, chiefly fuel, may be somewhat different in the new incremental plant compared to the old average plant; where the difference is between nuclear fuel and fossil fuel, its size is substantial. However, given the same kind of plant, the current prices of materials and labor will be essentially the same whether used in the new or the old plant with long-run incremental costs (LRIC) or long-run average costs (LRAC). The lower cost of electricity produced in nuclear plants constructed today, as compared to fossil fuel plants constructed at the same time, is not to be confused with the relation between LRIC and LRAC. LRAC is the average cost of electricity from all existing plants priced at their historical costs, which were generally lower than current costs. These average historical costs per kilowatt are still likely to be lower than the current incremental cost per kilowatt of the newest nuclear plant built at present price levels. LRAC is, therefore, still likely to be lower than LRIC for either fossil or nuclear. Data from the Wisconsin Power and Light Company, the Madison Gas and Electric Company, and Tuscon Gas and Electric Company are examined to study some comparisons. Some pricing principles that vary seasonally for resort hotels are reviewed. (MCW)

Morton, W.A.

1976-03-25T23:59:59.000Z

207

Commerce study looks at cost of pollution control for fossil-fuel power industry  

SciTech Connect

Environmental controls for fossil-fuel power plants consumed 1.3 percent of the national fuel used in 1974, with the largest demand going for sulfur dioxide emission control. Projections for power plant consumption to meet environmental standards range as high as eight percent in the 1980s. Less-energy-consuming systems include coal blending, tall stacks, and supplementary control systems; while high consumers are using coal washing operations in place of scrubbers, fuel transportation, conversion to acceptable fuels, waste heat disposal, and particulate controls. A summary table presents sulfur dioxide regulations in terms of their goals and their anticipated minimum and maximum fuel consumption. (DCK)

1977-06-01T23:59:59.000Z

208

Development of Low-Cost Manufacturing Processes for Planar, Multilayer Solid Oxide Fuel Cell Elements  

DOE Green Energy (OSTI)

This report summarizes the results of Phase II of this program, 'Low-Cost Manufacturing Of Multilayer Ceramic Fuel Cells'. The objective of the program is to develop advanced ceramic manufacturing technologies for making planar solid oxide fuel cell (SOFC) components that are more economical and reliable for a variety of applications. Phase II development work focused on three distinct manufacturing approaches (or tracks) for planar solid oxide fuel cell elements. Two development tracks, led by NexTech Materials and Oak Ridge National Laboratory, involved co-sintering of planar SOFC elements of cathode-supported and anode-supported variations. A third development track, led by the University of Missouri-Rolla, focused on a revolutionary approach for reducing operating temperature of SOFCs by using spin-coating to deposit ultra-thin, nano-crystalline YSZ electrolyte films. The work in Phase II was supported by characterization work at Ohio State University. The primary technical accomplishments within each of the three development tracks are summarized. Track 1--NexTech's targeted manufacturing process for planar SOFC elements involves tape casting of porous electrode substrates, colloidal-spray deposition of YSZ electrolyte films, co-sintering of bi-layer elements, and screen printing of opposite electrode coatings. The bulk of NexTech's work focused on making cathode-supported elements, although the processes developed at NexTech also were applied to the fabrication of anode-supported cells. Primary accomplishments within this track are summarized below: (1) Scale up of lanthanum strontium manganite (LSM) cathode powder production process; (2) Development and scale-up of tape casting methods for cathode and anode substrates; (3) Development of automated ultrasonic-spray process for depositing YSZ films; (4) Successful co-sintering of flat bi-layer elements (both cathode and anode supported); (5) Development of anode and cathode screen-printing processes; and (6) Demonstration of novel processes for composite cathode and cermet anode materials. Track 2--ORNL's development work focused solely on making anode-supported planar cells by tape casting of a porous anode substrate, screen printing of a YSZ electrolyte film, co-sintering of the bi-layer element, and screen-printing of an opposite cathode coating. Primary accomplishments within this track are summarized below: (1) Development and scale-up of anode tape casting and lamination processes; (2) Development of proprietary ink vehicle for screen-printing processes; (3) Development of screen-printing process for depositing YSZ films; (4) Successful co-sintering of flat bi-layer anode-supported elements; and (5) Development of cathode screen-printing process. Track 3--UMR's process development work involved fabrication of a micro-porous cathode substrate, deposition of a nano-porous interlayer film, deposition of nano-crystalline YSZ electrolyte films from polymeric precursor solutions, and deposition of an anode coating. Primary accomplishments within this track are summarized below: (1) Development and scale up of tape casting and sintering methods for cathode substrates; (2) Deposition of nano-porous ceria interlayer films on cathode substrates; (3) Successful deposition of dense YSZ films on porous cathode substrates; and (4) Identification of several anode material options.

Scott Swartz; Matthew Seabaugh; William Dawson; Tim Armstrong; Harlan Anderson; John Lannutti

2001-09-30T23:59:59.000Z

209

2005 DOE Hydrogen Program Review PresentationCOST AND PERFORMANCE ENHANCEMENTS FOR A PEM FUEL CELL TURBOCOMPRESSOR  

DOE Green Energy (OSTI)

The objectives of the program during the past year was to complete Technical Objectives 2 and 3 and initiate Technical Objective 4 are described. To assist the Department of Energy in the development of a low cost, reliable and high performance air compressor/expander. Technical Objective 1: Perform a turbocompressor systems PEM fuel cell trade study to determine the enhanced turbocompressor approach. Technical Objective 2: Using the results from technical objective 1, an enhanced turbocompressor will be fabricated. The design may be modified to match the flow requirements of a selected fuel cell system developer. Technical Objective 3: Design a cost and performance enhanced compact motor and motor controller. Technical Objective 4: Turbocompressor/motor controller development.

Mark K. Gee

2005-04-01T23:59:59.000Z

210

Assessment of costs and benefits of flexible and alternative fuel use in the US transportation sector  

DOE Green Energy (OSTI)

The DOE is conducting a comprehensive technical analysis of a flexible-fuel transportation system in the United States -- that is, a system that could easily switch between petroleum and another fuel, depending on price and availability. The DOE Alternative Fuels Assessment is aimed directly at questions of energy security and fuel availability, but covers a wide range of issues. This report examines environmental, health, and safety concerns associated with a switch to alternative- and flexible-fuel vehicles. Three potential alternatives to oil-based fuels in the transportation sector are considered: methanol, compressed natural gas (CNG), and electricity. The objective is to describe and discuss qualitatively potential environmental, health, and safety issues that would accompany widespread use of these three fuels. This report presents the results of exhaustive literature reviews; discussions with specialists in the vehicular and fuel-production industries and with Federal, State, and local officials; and recent information from in-use fleet tests. Each chapter deals with the end-use and process emissions of air pollutants, presenting an overview of the potential air pollution contribution of the fuel --relative to that of gasoline and diesel fuel -- in various applications. Carbon monoxide, particulate matter, ozone precursors, and carbon dioxide are emphasized. 67 refs., 6 figs. , 8 tabs.

Not Available

1991-10-01T23:59:59.000Z

211

Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems for Automotive Applications: 2010 Update  

NLE Websites -- All DOE Office Websites (Extended Search)

Mass Production Cost Estimation for Direct H 2 PEM Fuel Cell Systems for Automotive Applications: 2010 Update September 30, 2010 Prepared by: Brian D. James, Jeffrey A. Kalinoski & Kevin N. Baum One Virginia Square 3601 Wilson Boulevard, Suite 650 Arlington, Virginia 22201 703-243-3383 Prepared under: Subcontract No. AGB-0-40628-01 to the National Renewable Energy Laboratory (NREL) under Prime Contract No. DE-AC36-08GO28308 to the U.S. Department of Energy Foreword Energy security is fundamental to the mission of the U.S. Department of Energy (DOE) and hydrogen fuel cell vehicles have the potential to eliminate the need for oil in the transportation sector. Fuel cell vehicles can operate on hydrogen, which can be produced domestically, emitting less greenhouse gasses and pollutants than

212

Cost Impact of Using ISG-8 Rev. 3 for PWR Spent Fuel Pool Criticality Analysis  

Science Conference Proceedings (OSTI)

Nuclear Regulatory Commission (NRC) guidance for applying burnup credit in criticality analyses for spent fuel storage and transportation requirements recently changed with the release of Interim Staff Guidance (ISG) 8 Revision 3, Burnup Credit in the Criticality Safety Analyses of PWR Spent Fuel in Transportation and Storage Casks. If ISG-8 Rev. 3 were imposed upon pressurized water reactor (PWR) spent fuel pool (SFP) criticality analyses, the burnup requirements for loading would ...

2012-11-21T23:59:59.000Z

213

Microsoft Word - 2011 fuel costs per mile w-header.doc  

NLE Websites -- All DOE Office Websites (Extended Search)

of driving an electric vehicle depends on the cost of electricity per kilowatt-hour (kWh) and the energy efficiency of the vehicle. For example, to determine the energy cost...

214

Low-Cost PEM Fuel Cell Metal Bipolar Plates - DOE Hydrogen and...  

NLE Websites -- All DOE Office Websites (Extended Search)

Progress Report DOE Hydrogen and Fuel Cells Program Conghua "CH" Wang TreadStone Technologies, Inc. 201 Washington Rd. Princeton, NJ 08543 Phone: (609) 734-3071 Email:...

215

DOE Fuel Cell Technologies Office Record 13010: Onboard Type IV Compressed Hydrogen Storage Systems - Current Performance and Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

DOE Fuel Cell Technologies Office Record Record #: 13010 Date: June 11, 2013 Title: Onboard Type IV Compressed Hydrogen Storage Systems - Current Performance and Cost Originators: Scott McWhorter and Grace Ordaz Approved by: Sunita Satyapal Date: July 17, 2013 Item: This record summarizes the current status of the projected capacities and manufacturing costs of Type IV, 350- and 700-bar compressed hydrogen storage systems, storing 5.6 kg of usable hydrogen, for onboard light-duty automotive applications when manufactured at a volume of 500,000 units per year. The current projected performance and cost of these systems are presented in Table 1 against the DOE Hydrogen Storage System targets. These analyses were performed in support of the Hydrogen Storage

216

Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems for Automotive Application  

NLE Websites -- All DOE Office Websites (Extended Search)

presentation presentation does not contain any proprietary, confidential, or otherwise restricted information page 1 Overview * Base Period: - 100% complete * Manufacturing costs * Materials costs (particularly precious Timeline Barriers - Feb 17, 2006 to Feb. 16, 2008 * Option year 1 of 3: - 65% complete - Started Feb 16, 2008 metal catalysts) Characteristic Units 2008 2010 2015 Stack Cost $/kW e (net) - $25 $15 - $325K (2 year base period) - $182k (opt. yr. 1) - Contractor share: $0 * Funding for FY 2008 * Extensive interaction with Collaborations System Cost $/kW e (net) - $45 $30 * Funding for FY 2008 - $182k industry/researchers to solicit design & manufacturing metrics as input to cost analysis. page 2 Started Feb 16, 2008 Budget * Total project funding DOE Cost Targets

217

Rough cost estimates of solar thermal/coal or biomass-derived fuels. [Hybrid approach: solar thermal plus either coal or biomass  

SciTech Connect

The production of a synthetic fuel from a solar thermal resource could provide a means of replacing critical liquid and gaseous fossil fuels. The solar thermal resource is large and economics favors a southwestern site. A synthetic fuel would provide a desirable product and a means of transporting solar thermal energy to large load centers outside the southwest. This paper presents cost data for one method of producing synthetic methane. A hybrid approach was chosen, a combination of solar thermal and either coal or biomass. The magnitude of the solar thermal resource is estimated as well as projected cost. Cost projections for coal and biomass are accumulated. The cost of synthetic gas from a hybrid and a conventional fuel source are compared.

Copeland, R. J.

1979-01-01T23:59:59.000Z

218

mMass Production Cost Estimation for Direct H2 PEM Fuel Cell...  

NLE Websites -- All DOE Office Websites (Extended Search)

has not been included in this study. In general, the system designs do not change with production rate, but material costs, manufacturing methods, and business-operational...

219

Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems...  

NLE Websites -- All DOE Office Websites (Extended Search)

has not been included in this study. In general, our system designs do not change with production rate, but material costs, manufacturing methods, and business-operational...

220

Cost modeling approach and economic analysis of biomass gasification integrated solid oxide fuel cell systems  

Science Conference Proceedings (OSTI)

This paper presents a cost modeling approach and the economic feasibility for selected plant configurations operating under three modes: air gasification

Rajesh S. Kempegowda; Øyvind Skreiberg; Khanh-Quang Tran

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

A cost-effective and fuel-conserving nonelectric air conditioner that combines engine-driven compression and absorption cycles  

SciTech Connect

A natural-gas-fueled electricity-producing condensing furnace with the potential of being mass produced at a cost of less than $1000 and providing a cost-effective and highly fuel-conserving alternative to virtually every residential gas furnace in the world has been developed. While this is a new system, it completely consists of existing mass-produced components including single-cylinder air-cooled engines, induction motors/generators, and control devices. Thus, timely commercialization can be expected and an important new energy technology and industry can result. However, all the benefits of this electricity-producing furnace occur during the winter. This has stimulated the search for a new system that can provide comparable benefits in terms of fuel conservation, the environment, and electric utility peak reduction during the summer, along with the prospects of a new and efficient new use for the natural gas surpluses that occur during the summer. The resulting system, which can use existing component equipment, is a commercial-size nonelectric air conditioner that consists of an automobile-type engine converted to natural gas, or possibly a diesel or combustion turbine, driving a Freon compression cycle, with virtually all of the engine reject heat from the exhaust and from the engine cooling system driving a conventional absorption air conditioning cycle.

Wicks, F.

1988-01-01T23:59:59.000Z

222

Cost-effectiveness of controlling emissions for various alternative-fuel vehicle types, with vehicle and fuel price subsidies estimated on the basis of monetary values of emission reductions  

DOE Green Energy (OSTI)

Emission-control cost-effectiveness is estimated for ten alternative-fuel vehicle (AFV) types (i.e., vehicles fueled with reformulated gasoline, M85 flexible-fuel vehicles [FFVs], M100 FFVs, dedicated M85 vehicles, dedicated M100 vehicles, E85 FFVS, dual-fuel liquefied petroleum gas vehicles, dual-fuel compressed natural gas vehicles [CNGVs], dedicated CNGVs, and electric vehicles [EVs]). Given the assumptions made, CNGVs are found to be most cost-effective in controlling emissions and E85 FFVs to be least cost-effective, with the other vehicle types falling between these two. AFV cost-effectiveness is further calculated for various cases representing changes in costs of vehicles and fuels, AFV emission reductions, and baseline gasoline vehicle emissions, among other factors. Changes in these parameters can change cost-effectiveness dramatically. However, the rank of the ten AFV types according to their cost-effectiveness remains essentially unchanged. Based on assumed dollars-per-ton emission values and estimated AFV emission reductions, the per-vehicle monetary value of emission reductions is calculated for each AFV type. Calculated emission reduction values ranged from as little as $500 to as much as $40,000 per vehicle, depending on AFV type, dollar-per-ton emission values, and baseline gasoline vehicle emissions. Among the ten vehicle types, vehicles fueled with reformulated gasoline have the lowest per-vehicle value, while EVs have the highest per-vehicle value, reflecting the magnitude of emission reductions by these vehicle types. To translate the calculated per-vehicle emission reduction values to individual AFV users, AFV fuel or vehicle price subsidies are designed to be equal to AFV emission reduction values. The subsidies designed in this way are substantial. In fact, providing the subsidies to AFVs would change most AFV types from net cost increases to net cost decreases, relative to conventional gasoline vehicles.

Wang, M.Q.

1993-12-31T23:59:59.000Z

223

Economic costs and environmental impacts of alternative fuel vehicle fleets in local government: An interim assessment  

E-Print Network (OSTI)

; Environmental policy 1. Introduction High crude oil prices and increasing public awareness of the environmental and fuel provider fleet vehicles (US Department of Energy, 2006). Nevertheless, fleets covered under

Illinois at Chicago, University of

224

Cost-benefit analysis of ultra-low sulfur jet fuel  

E-Print Network (OSTI)

The growth of aviation has spurred increased study of its environmental impacts and the possible mitigation thereof. One emissions reduction option is the introduction of an Ultra Low Sulfur (ULS) jet fuel standard for ...

Kuhn, Stephen (Stephen Richard)

2010-01-01T23:59:59.000Z

225

Development of an energy consumption and cost data base for fuel cell total energy systems and conventional building energy systems  

DOE Green Energy (OSTI)

This report describes the procedures and data sources used to develop an energy-consumption and system-cost data base for use in predicting the market penetration of phosphoric acid fuel cell total-energy systems in the nonindustrial building market. A computer program was used to simulate the hourly energy requirements of six types of buildings - office buildings, retail stores, hotels and motels, schools, hospitals, and multifamily residences. The simulations were done by using hourly weather tapes for one city in each of the ten Department of Energy administrative regions. Two types of building construction were considered, one for existing buildings and one for new buildings. A fuel cell system combined with electrically driven heat pumps and one combined with a gas boiler and an electrically driven chiller were compared with similar conventional systems. The methods of system simulation, component sizing, and system cost estimation are described for each system. The systems were simulated for a single building size for each building type. Methods were developed to extrapolate the system cost and performance data to other building sizes.

Pine, G.D.; Christian, J.E.; Mixon, W.R.; Jackson, W.L.

1980-07-01T23:59:59.000Z

226

Carbonate fuel cell monolith design for high power density and low cost  

SciTech Connect

Objective is higher power density operation and cost reduction. This is accomplished by the design of a bipolar plate where the separate corrugated current collectors are eliminated; cost reduction was also derived through higher power density and reduced material usage. The higher volumetric power density operation was achieved through lower cell resistance, increased active component surface area, and reduced cell height.

Allen, J.; Doyon, J.

1996-08-01T23:59:59.000Z

227

DOE Hydrogen and Fuel Cells Program Record 13013: Hydrogen Delivery Cost Projections - 2013  

NLE Websites -- All DOE Office Websites (Extended Search)

3013 Date: September 26, 2013 3013 Date: September 26, 2013 Title: H 2 Delivery Cost Projections - 2013 Originator: E. Sutherland, A. Elgowainy and S. Dillich Approved by: R. Farmer and S. Satyapal Date: December 18, 2013 Item: Reported herein are past 2005 and 2011 estimates, current 2013 estimates, 2020 projected cost estimates and the 2015 and 2020 target costs for delivering and dispensing (untaxed) H 2 to 10%- 15% of vehicles within a city population of 1.2M from a centralized H 2 production plant located 100 km from the city gate. The 2011 volume cost estimates are based on the H2A Hydrogen Delivery Scenario Analysis Model (HDSAM) V2.3 projections and are employed as the basis for defining the cost and technical targets of delivery components in Table 3.2.4 in the 2012 Delivery

228

DOE Hydrogen and Fuel Cells Program Record 5040: 2005 Hydrogen Cost from Water Electrolysis  

NLE Websites -- All DOE Office Websites (Extended Search)

40 Date: December 12, 2008 40 Date: December 12, 2008 Title: 2005 Hydrogen Cost from Water Electrolysis Originator: Roxanne Garland Approved by: Sunita Satyapal Date: December 19, 2008 Item: The 2005 cost status for hydrogen produced from distributed water electrolysis is $5.90 / gge. Assumptions and References: The H2A analysis used to determine the projected cost of $5.88/gge (rounded up to $5.90/gge) was performed by Directed Technologies, Inc. and can be found in Record 5040a. The increase in cost compared to the 2004 analysis ($5.45/gge) is due to two assumptions changed in the model: (a) an increase in the industrial electricity price from 5¢/kWh to 5.5¢/kWh from the EIA Annual Energy Outlook, and (b) an increase in the capital cost estimate of the electrolyzer. The other assumptions in the analysis used standard values

229

Hydrogen Storage Cost Analysis, Preliminary Results - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

2 2 DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report Brian D. James (Primary Contact), Andrew B. Spisak, Whitney G. Colella Strategic Analysis, Inc. 4075 Wilson Blvd. Suite 200 Arlington, VA 22203 Phone: (703) 778-7114 E-mail: bjames@sainc.com DOE Managers HQ: Grace Ordaz Phone: (202) 586-8350 Email: Grace.Ordaz@ee.doe.gov GO: Katie Randolph Phone: (720) 356-1759 Email: Katie.Randolph@go.doe.gov Contract Number: DE-EE0005253 Project Start Date: September 30, 2012 Project End Date: September 29, 2016 Fiscal Year (FY) 2012 Objectives Develop cost models of carbon fiber hydrogen storage * pressure vessels. Explore the sensitivity of pressure vessel cost to design * parameters including hydrogen storage quantity, storage

230

An economic feasibility analysis of distributed electric power generation based upon the Natural Gas-Fired Fuel Cell: a model of the operations cost.  

DOE Green Energy (OSTI)

This model description establishes the revenues, expenses incentives and avoided costs of Operation of a Natural Gas-Fired Fuel Cell-Based. Fuel is the major element of the cost of operation of a natural gas-fired fuel cell. Forecasts of the change in the price of this commodity a re an important consideration in the ownership of an energy conversion system. Differences between forecasts, the interests of the forecaster or geographical areas can all have significant effects on imputed fuel costs. There is less effect on judgments made on the feasibility of an energy conversion system since changes in fuel price can affect the cost of operation of the alternatives to the fuel cell in a similar fashion. The forecasts used in this model are only intended to provide the potential owner or operator with the means to examine alternate future scenarios. The operations model computes operating costs of a system suitable for a large condominium complex or a residential institution such as a hotel, boarding school or prison. The user may also select large office buildings that are characterized by 12 to 16 hours per day of operation or industrial users with a steady demand for thermal and electrical energy around the clock.

Not Available

1993-06-30T23:59:59.000Z

231

Optimal Control of the Solid Fuel Ignition Model with H1-Cost  

Science Conference Proceedings (OSTI)

Optimal control problems for the stationary as well as the time-dependent solid fuel ignition model are investigated. Existence of optimal controls is proved, and optimality systems are derived. The analysis is based on a closedness lemma for the exponential ... Keywords: control of exponential nonlinearity, explosion phenomena, optimal control, optimality conditions

Kazufumi Ito; Karl Kunisch

2001-05-01T23:59:59.000Z

232

Life-cycle cost comparisons of advanced storage batteries and fuel cells for utility, stand-alone, and electric vehicle applications  

DOE Green Energy (OSTI)

This report presents a comparison of battery and fuel cell economics for ten different technologies. To develop an equitable economic comparison, the technologies were evaluated on a life-cycle cost (LCC) basis. The LCC comparison involved normalizing source estimates to a standard set of assumptions and preparing a lifetime cost scenario for each technology, including the initial capital cost, replacement costs, operating and maintenance (O M) costs, auxiliary energy costs, costs due to system inefficiencies, the cost of energy stored, and salvage costs or credits. By considering all the costs associated with each technology over its respective lifetime, the technology that is most economical to operate over any given period of time can be determined. An analysis of this type indicates whether paying a high initial capital cost for a technology with low O M costs is more or less economical on a lifetime basis than purchasing a technology with a low initial capital cost and high O M costs. It is important to realize that while minimizing cost is important, the customer will not always purchase the least expensive technology. The customer may identify benefits associated with a more expensive option that make it the more attractive over all (e.g., reduced construction lead times, modularity, environmental benefits, spinning reserve, etc.). The LCC estimates presented in this report represent three end-use applications: utility load-leveling, stand-alone power systems, and electric vehicles.

Humphreys, K.K.; Brown, D.R.

1990-01-01T23:59:59.000Z

233

Program Record 13006 (Offices of Vehicle Technologies and Fuel Cell Technologies: Life-Cycle Costs of Mid-Size Light-Duty Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Program Record (Offices of Vehicle Technologies & Fuel Cell Program Record (Offices of Vehicle Technologies & Fuel Cell Technologies) Record #: 13006 Date: April 24, 2013 Title: Life-cycle Costs of Mid-Size Light-Duty Vehicles Originator: Tien Nguyen & Jake Ward Approved by: Sunita Satyapal Pat Davis Date: April 25, 2013 Items: DOE is pursuing a portfolio of technologies with the potential to significantly reduce greenhouse gases (GHG) emissions and petroleum consumption while being cost-effective. This record documents the assumptions and results of analyses conducted to estimate the life-cycle costs resulting from several fuel/vehicle pathways, for a future mid-size car. The results are summarized graphically in the following figure. Costs of Operation for Future Mid-Size Car

234

DOE Hydrogen Analysis Repository: Hydrogen Infrastructure Costs  

NLE Websites -- All DOE Office Websites (Extended Search)

Infrastructure Costs Project Summary Full Title: Fuel Choice for Fuel Cell Vehicles: Hydrogen Infrastructure Costs Previous Title(s): Guidance for Transportation Technologies: Fuel...

235

Labor Standards Interview Form | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Standards Interview Form Labor Standards Interview Form SF 1445.pdf More Documents & Publications Labor Standards for Construction Chapter 22 - Labor Standards for Construction CRB...

236

Estimating the marginal cost of reducing global fossil fuel CO[sub 2] emissions  

Science Conference Proceedings (OSTI)

This paper estimates the marginal, total, and average cost and effectiveness of carbon taxes applied either by the Organization for Economic Cooperation and Development (OECD) members alone, or as part of a global cooperative strategy, to reduce potential future emissions and their direct implications for employment in the US coal industry. Two sets of cases are examined, one set in which OECD members acts alone, and another set in which the world acts in concert. In each case set taxes are examined which achieve four alternative levels of emissions reduction: halve the rate of emissions growth, no emissions growth, 20[percent] reduction from 1988 levels, and 50[percent] reduction from 1988 levels. For the global cooperation case, carbon tax rates of [dollar sign]32, [dollar sign]113, [dollar sign]161, and [dollar sign]517 per metric ton of carbon (mtC) were needed in the year 2025 to achieve the objectives. Total costs were respectively [dollar sign]40, [dollar sign]178, [dollar sign]253, and [dollar sign]848 billions of 1990 US dollars per year in the year 2025. Average costs were [dollar sign]32, [dollar sign]55, [dollar sign]59, and [dollar sign]135 per mtC. Costs were significantly higher in the cases in which the OECD members states acted alone. OECD member states, acting alone, could not reduce global emissions by 50[percent] or 20[percent] relative to 1988, given reference case assumptions regarding developing and recently planned nations economic growth.

Edmonds, J.; Barns, D.W.; McDonald, S. (Pacific Northwest Lab., Washington, DC (United States))

1992-01-01T23:59:59.000Z

237

Department of Energy Awards Nearly $7 Million to Advance Fuel Cell and  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Awards Nearly $7 Million to Advance Fuel Cell Awards Nearly $7 Million to Advance Fuel Cell and Hydrogen Storage Systems Research Department of Energy Awards Nearly $7 Million to Advance Fuel Cell and Hydrogen Storage Systems Research August 9, 2011 - 11:21am Addthis California, Ohio, and Virginia Projects to Find Ways to Reduce Component and Manufacturing Costs Washington, D.C. - The U.S. Department of Energy today announced nearly $7 million over five years for independent cost analyses that will support research and development efforts for fuel cells and hydrogen storage systems. The four projects - in California, Ohio, and Virginia - will generate rigorous cost estimates for manufacturing equipment, labor, energy, raw materials, and various components that will help identify ways to drive down production costs of transportation fuel cell systems,

238

Aging and the labor market  

E-Print Network (OSTI)

This thesis is a collection of three essays analyzing the interplay between aging and the labor market. The first chapter demonstrates that differential treatment by age exists in labor markets and explores different ...

Lahey, Joanna

2005-01-01T23:59:59.000Z

239

Small-Scale Low Cost Solid Oxide Fuel Cell Power Systems  

DOE Green Energy (OSTI)

Progress in tasks seeking greater cell power density and lower cost through new cell designs, new cell materials and lower operating temperature is summarized. The design of the program required Proof-of-Concept unit of residential capacity scale is reviewed along with a summary of results from its successful test. Attachment 1 summarizes the status of cell development. Attachment 2 summarizes the status of generator design, and Attachment 3 of BOP design.

S. D. Vora

2008-02-01T23:59:59.000Z

240

Development of a Low-Cost, Durable Membrane and MEA for Stationary and Mobile Fuel Cell Applications  

DOE Green Energy (OSTI)

The development of low cost, durable membranes and membranes electrode assemblies (MEAs) remain a critical challenge for the successful introduction of fuel cells into mass markets. It was the goal of the team lead by Arkema, Inc. (formerly Atofina, Inc.) to address these shortages. Thus, this project addresses the following technical barriers from the Fuel Cells section of the Hydrogen Fuel Cells and Infrastructure Technologies Program Multi-Year Research, Development and Demonstration Plan: (A) Durability (B) Cost Arkema’s approach consisted in using blends of polyvinylidenefluoride (PVDF) and proprietary sulfonated polyelectrolytes. The strength and originality of Arkema’s approach lies in the decoupling of ion conductivity from the other requirements. Kynar® (Arkema trade name for PVDF) provides an exceptional combination of properties that make it ideally suited for a membrane matrix. In a first phase, Arkema demonstrated the feasibility of the concept with the M31 membrane generation. After MEA optimization, it was shown that the beginning-of-life (BOL) performance of M31 MEAs was essentially on a par with that of PFSA MEAs at 60ºC under fully humidified conditions. On the other hand, long-term durability studies showed a high decay rate of 45µV/h over a 2100 hr. test. Arkema then designed several families of polyelectrolyte candidates, which – in principle – could not undergo the same failure mechanisms. A new membrane candidate was developed: M41. It offered the same generally good mechanical, ex-situ conductivity and gas barrier properties as M31. In addition, ex-situ accelerated testing suggested a several orders of magnitude improvement in chemical stability. M41 based MEAs showed comparable BOL performance with that of PFSA (80ºC, 100% RH). M41 MEAs were further shown to be able to withstand several hours temperature excursions at 120ºC without apparent damage. Accelerated studies were carried out using the DOE and/or US Fuel Cell Council protocols. M41 MEAs shown sizeable advantages over PFSA MEAs in the Open Circuit Voltage Hold test, Relative Humidity Cycling test and the Voltage Cycling test. The main known limitation of the M41 family is its ability to function well at low RH.

Michel Foure, Scott Gaboury, Jim Goldbach, David Mountz and Jung Yi (no longer with company)

2008-01-31T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Comparative analysis of the production costs and life-cycle GHG emissions of FT liquid fuels from coal and natural gas  

SciTech Connect

Liquid transportation fuels derived from coal and natural gas could help the United States reduce its dependence on petroleum. The fuels could be produced domestically or imported from fossil fuel-rich countries. The goal of this paper is to determine the life-cycle GHG emissions of coal- and natural gas-based Fischer-Tropsch (FT) liquids, as well as to compare production costs. The results show that the use of coal- or natural gas-based FT liquids will likely lead to significant increases in greenhouse gas (GHG) emissions compared to petroleum-based fuels. In a best-case scenario, coal- or natural gas-based FT-liquids have emissions only comparable to petroleum-based fuels. In addition, the economic advantages of gas-to-liquid (GTL) fuels are not obvious: there is a narrow range of petroleum and natural gas prices at which GTL fuels would be competitive with petroleum-based fuels. CTL fuels are generally cheaper than petroleum-based fuels. However, recent reports suggest there is uncertainty about the availability of economically viable coal resources in the United States. If the U.S. has a goal of increasing its energy security, and at the same time significantly reducing its GHG emissions, neither CTL nor GTL consumption seem a reasonable path to follow. 28 refs., 2 figs., 4 tabs.

Paulina Jaramillo; W. Michael Griffin; H. Scott Matthews [Carnegie Mellon University, Pittsburgh, PA (USA). Civil and Environmental Engineering Department

2008-10-15T23:59:59.000Z

242

Reducing Ultra-Clean Transportation Fuel Costs with HyMelt Hydrogen  

DOE Green Energy (OSTI)

This report describes activities for the thirteenth quarter of work performed under this agreement. EnviRes initiated a wire transfer of funds for procurement of a pressure vessel and associated refractory lining. Phase I of the work to be done under this agreement consisted of conducting atmospheric gasification of coal using the HyMelt technology to produce separate hydrogen rich and carbon monoxide rich product streams. In addition smaller quantities of petroleum coke and a low value refinery stream were gasified. Phase II of the work to be done under this agreement, consists of gasification of the above-mentioned feeds at a gasifier pressure of approximately 5 bar. The results of this work will be used to evaluate the technical and economic aspects of producing ultra-clean transportation fuels using the HyMelt technology in existing and proposed refinery configurations.

Donald P. Malone; William R. Renner

2006-01-01T23:59:59.000Z

243

Reducing Ultra-Clean Transportation Fuel Costs with HyMelt Hydrogen  

DOE Green Energy (OSTI)

Phase I of the work to be done under this agreement consisted of conducting atmospheric gasification of coal using the HyMelt technology to produce separate hydrogen rich and carbon monoxide rich product streams. In addition smaller quantities of petroleum coke and a low value refinery stream were gasified. Phase II of the work to be done under this agreement, consists of gasification of the above-mentioned feeds at a gasifier pressure of approximately 5 bar. The results of this work will be used to evaluate the technical and economic aspects of producing ultra-clean transportation fuels using the HyMelt technology in existing and proposed refinery configurations. This report describes activities for the thirteenth quarter of work performed under this agreement. MEFOS, the gasification testing subcontractor, reported to EnviRes that they were having difficulty with refractory vendors meeting specifications for the lining of the pressure vessel. EnviRes is working to resolve this issue.

Donald P. Malone; William R. Renner

2006-04-01T23:59:59.000Z

244

Flex-fuel Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Vehicles Stations that Sell E85 (Alternative Fuels and Advanced Vehicles Data Center AFDC) Flexible Fuel Vehicle (FFV) Cost Calculator (compare costs for operating your vehicle...

245

Preliminary Design and Cost Structure of a 50-kW Polymer Electrolyte Membrane Fuel Cell (PEMFC) System for Stationary Applications  

Science Conference Proceedings (OSTI)

There is a growing interest in using Polymer Electrolyte Membrane Fuel Cell (PEMFC) technology in commercial on-site power and co-generation systems. However, little quantitative information is available on such factors as cost structure, size/weight characteristics, and cost/performance tradeoffs. This report both updates and refines results of prior studies to provide a more quantitative basis for developing a program that supports sound product strategy and business decisions.

1998-12-31T23:59:59.000Z

246

Analysis of environmental factors impacting the life cycle cost analysis of conventional and fuel cell/battery-powered passenger vehicles. Final report  

DOE Green Energy (OSTI)

This report presents the results of the further developments and testing of the Life Cycle Cost (LCC) Model previously developed by Engineering Systems Management, Inc. (ESM) on behalf of the U.S. Department of Energy (DOE) under contract No. DE-AC02-91CH10491. The Model incorporates specific analytical relationships and cost/performance data relevant to internal combustion engine (ICE) powered vehicles, battery powered electric vehicles (BPEVs), and fuel cell/battery-powered electric vehicles (FCEVs).

NONE

1995-01-31T23:59:59.000Z

247

Reducing Ultra-Clean Transportation Fuel Costs with HyMelt Hydrogen  

DOE Green Energy (OSTI)

This report describes activities for the sixteenth quarter of work performed under this agreement. MEFOS, the gasification testing subcontractor, reported to EnviRes that the vendor for the pressure vessel for above atmospheric testing now plans to deliver it by November 20, 2006 instead of October 20, 2006 as previously reported. MEFOS performed a hazardous operation review of pressurized testing. The current schedule anticipates above atmospheric pressure testing to begin during the week of April 16, 2007. Phase I of the work to be done under this agreement consisted of conducting atmospheric gasification of coal using the HyMelt technology to produce separate hydrogen rich and carbon monoxide rich product streams. In addition smaller quantities of petroleum coke and a low value refinery stream were gasified. Phase II of the work to be done under this agreement, consists of gasification of the above-mentioned feeds at a gasifier pressure of approximately 3 bar. The results of this work will be used to evaluate the technical and economic aspects of producing ultra-clean transportation fuels using the HyMelt technology in existing and proposed refinery configurations.

Donald P. Malone; William R. Renner

2006-09-30T23:59:59.000Z

248

COMPARATIVE COST STUDY OF PROCESSING STAINLESS STEEL-JACKETED UO$sub 2$ FUEL: MECHANICAL SHEAR-LEACH VS SULFEX-CORE DISSOLUTION  

SciTech Connect

The economics of mechanical shear-leach and Sulfex decladding-core dissolution head end treatments for processing typical tubular bundles of stainless steel-jacketed UO/sub 2/ nuclear fuels were compared. A 2.66 metric ton U/day head end portion of a plant was designed for each process and capital and operating costs were developed. For plants of this size and larger, mechanical shear-leach processing has the advantage of ~20% lower capital cost and 50% lower operating cost. Processing costs of stainless steel-jacketed UO/ sub 2/ by the Sulfex and shear-leach methods, including amortization and waste disposal but excluding solvent extraction, were .78 and 7l/kg U, respectively. Storage of stainless steel waste produced by the shear-leach method is less costly by a factor of 20 than for Sulfex. (auth)

Adams, J.B.; Benis, A.M.; Watson, C.D.

1962-04-23T23:59:59.000Z

249

Fuels  

NLE Websites -- All DOE Office Websites (Extended Search)

Goals > Fuels Goals > Fuels XMAT for nuclear fuels XMAT is ideally suited to explore all of the radiation processes experienced by nuclear fuels.The high energy, heavy ion accleration capability (e.g., 250 MeV U) can produce bulk damage deep in the sample, achieving neutron type depths (~10 microns), beyond the range of surface sputtering effects. The APS X-rays are well matched to the ion beams, and are able to probe individual grains at similar penetrations depths. Damage rates to 25 displacements per atom per hour (DPA/hr), and doses >2500 DPA can be achieved. MORE» Fuels in LWRs are subjected to ~1 DPA per day High burn-up fuel can experience >2000 DPA. Traditional reactor tests by neutron irradiation require 3 years in a reactor and 1 year cool down. Conventional accelerators (>1 MeV/ion) are limited to <200-400 DPAs, and

250

Impact of DOE Program Goals on Hydrogen Vehicles: Market Prospect, Costs, and Benefits - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

9 9 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Zhenhong Lin (Primary Contact), David Greene, Jing Dong Oak Ridge National Laboratory (ORNL) National Transportation Research Center 2360 Cherahala Boulevard Knoxville, TN 37932 Phone: (865) 946-1308 Email: linz@ornl.gov DOE Manager HQ: Fred Joseck Phone: (202) 586-7932 Email: Fred.Joseck@hq.doe.gov Project Start Date: October 2011 Project End Date: September 2012 Fiscal Year (FY) 2012 Objectives Project market penetrations of hydrogen vehicles under * varied assumptions on processes of achieving the DOE program goals for fuel cells, hydrogen storage, batteries, motors, and hydrogen supply. Estimate social benefits and public costs under different *

251

What solar heating costs  

SciTech Connect

Few people know why solar energy systems cost what they do. Designers and installers know what whole packages cost, but rarely how much goes to piping, how much for labor and how much for the collectors. Yet one stands a better chance of controlling costs if one can compare where the money is going against where it should be going. A detailed Tennessee Valley Authority study of large solar projects shows how much each component contributes to the total bill.

Adams, J.A.

1985-05-01T23:59:59.000Z

252

Labor Relations | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Labor Relations Labor Relations Labor Relations Department of Energy Headquarters and The National Treasury Employees Union (NTEU) Collective Bargaining Agreement The National Treasury Employees Union (NTEU) is the exclusive representative of bargaining unit employees at the Department of Energy Headquarters offices in the Washington DC metropolitan area. The terms and conditions of this agreement have been negotiated by DOE and NTEU, and prescribe their respective rights and obligations in matters related to conditions of employment. Headquarters 1187 Request For Payroll Deductions For Labor Organization Dues The Request for Payroll Deduction for Labor Organization Dues (SF-1187) permits eligible employees, who are members of the National Treasury Employees Union (NTEU), to authorize voluntary allotments from their

253

Labor Standards for Construction  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of Project Management with Contract Management for Non-Management and Operating (M&O) Cost Reimbursement Contracts for Capital Asset Projects, Environmental Remediation,...

254

Labor Standards for Construction  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

fuels required by the Energy Policy Act of 2005. Find information at http:www.afdc.energy.govafdc . o Biobased products designated by the U.S. Department of Agriculture...

255

Development of a Low-Cost 3-10 kW Tubular SOFC Power System - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

7 7 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Norman Bessette Acumentrics Corporation 20 Southwest Park Westwood, MA 02090 Phone: (781) 461-8251; Email: nbessette@acumentrics.com DOE Managers HQ: Dimitrios Papageorgopoulos Phone: (202) 586-5463 Email: Dimitrios.Papageorgopoulos@ee.doe.gov GO: Reginald Tyler Phone: (720) 356-1805 Email: Reginald.Tyler@go.doe.gov Contract Number: DE-FC36-03NT41838 Project Start Date: April 1, 2008 Project End Date: March 31, 2013 Fiscal Year (FY) 2012 Objectives The goal of the project is to develop a low-cost 3-10 kW solid oxide fuel cell (SOFC) power generator capable of meeting multiple market applications. This is accomplished by: Improving cell power and stability * Cost reduction of cell manufacturing

256

The economics of alternative fuel cycles on sodium-cooled fast reactors and uncertainty and sensitivity analysis of cost estimates  

E-Print Network (OSTI)

Previous work was done to create a baseline capital cost model for the SFR in which case studies were performed to identify ways to decrease the capital costs while maintaining safety and performance. This thesis expands ...

Russo, Genevieve V. (Genevieve Virgina)

2010-01-01T23:59:59.000Z

257

NREL: News - New Study Shows Solar Manufacturing Costs Not Driven...  

NLE Websites -- All DOE Office Websites (Extended Search)

take an in-depth look at national competitiveness in PV manufacturing September 5, 2013 Production scale, not lower labor costs, drives China's current advantage in manufacturing...

258

Fuel  

E-Print Network (OSTI)

heavy-water-moderated, light-water-moderated and liquid-metal cooled fast breeder reactors fueled with natural or low-enriched uranium and containing thorium mixed with the uranium or in separate target channels. U-232 decays with a 69-year half-life through 1.9-year half-life Th-228 to Tl-208, which emits a 2.6 MeV gamma ray upon decay. We find that pressurized light-water-reactors fueled with LEU-thorium fuel at high burnup (70 MWd/kg) produce U-233 with U-232 contamination levels of about 0.4 percent. At this contamination level, a 5 kg sphere of U-233 would produce a gammaray dose rate of 13 and 38 rem/hr at 1 meter one and ten years after chemical purification respectively. The associated plutonium contains 7.5 percent of the undesirable heat-generating 88-year half-life isotope Pu-238. However, just as it is possible to produce weapon-grade plutonium in low-burnup fuel, it is also practical to use heavy-water reactors to produce U-233 containing only a few ppm of U-232 if the thorium is segregated in “target ” channels and discharged a few times more frequently than the natural-uranium “driver ” fuel. The dose rate from a 5-kg solid sphere of U-233 containing 5 ppm U-232 could be reduced by a further factor of 30, to about 2 mrem/hr, with a close-fitting lead sphere weighing about 100 kg. Thus the proliferation resistance of thorium fuel cycles depends very much upon how they are implemented. The original version of this manuscript was received by Science & Global Security on

Jungmin Kang A

2001-01-01T23:59:59.000Z

259

Essays on European labor markets  

E-Print Network (OSTI)

Chapter 1 examines whether immigrants gain a comparative advantage relative to natives in highly protected labor markets. This may be the case if immigrants, being new to the country, are less aware of employment protection ...

Sa, Filipa

2008-01-01T23:59:59.000Z

260

The unit cost factors and calculation methods for decommissioning - Cost estimation of nuclear research facilities  

SciTech Connect

Available in abstract form only. Full text of publication follows: The uncertainties of decommissioning costs increase high due to several conditions. Decommissioning cost estimation depends on the complexity of nuclear installations, its site-specific physical and radiological inventories. Therefore, the decommissioning costs of nuclear research facilities must be estimated in accordance with the detailed sub-tasks and resources by the tasks of decommissioning activities. By selecting the classified activities and resources, costs are calculated by the items and then the total costs of all decommissioning activities are reshuffled to match with its usage and objectives. And the decommissioning cost of nuclear research facilities is calculated by applying a unit cost factor method on which classification of decommissioning works fitted with the features and specifications of decommissioning objects and establishment of composition factors are based. Decommissioning costs of nuclear research facilities are composed of labor cost, equipment and materials cost. Of these three categorical costs, the calculation of labor costs are very important because decommissioning activities mainly depend on labor force. Labor costs in decommissioning activities are calculated on the basis of working time consumed in decommissioning objects and works. The working times are figured out of unit cost factors and work difficulty factors. Finally, labor costs are figured out by using these factors as parameters of calculation. The accuracy of decommissioning cost estimation results is much higher compared to the real decommissioning works. (authors)

Kwan-Seong Jeong; Dong-Gyu Lee; Chong-Hun Jung; Kune-Woo Lee [Korea Atomic Energy Research Institute, Deokjin-dong 150, Yuseong-gu, Daejeon 305-353 (Korea, Republic of)

2007-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Labor Standards for Construction  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Chapter 43.3 (March 2013) Chapter 43.3 (March 2013) 1 Maintaining Alignment of Project Management with Contract Management for Non-Management and Operating (M&O) Cost Reimbursement Contracts for Capital Asset Projects, Environmental Remediation, Decontamination and Decommissioning, Facility Operations, and Other Major Projects Purpose and Applicability This chapter provides guidance on how Contracting Officers (COs) should manage contract changes, and how COs and Federal Project Directors (FPDs) should maintain alignment between project and contract management under non-M&O cost reimbursement contracts for capital asset projects, environmental remediation, decontamination and decommissioning, facility operations, and other projects. This chapter has three sections. Section I provides pre-award

262

Cost of Adding E85 Fueling Capability to Existing Gasoline Stations: NREL Survey and Literature Search (Fact Sheet)  

DOE Green Energy (OSTI)

Fact sheet provides framework for gas station owners to access what a reasonable cost would be to install E85 infrastructure.

Not Available

2008-03-01T23:59:59.000Z

263

New MEA Materials for Improved Direct Methanol Fuel Cell (DMFC) Performance, Durability, and Cost - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

6 6 DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report James Fletcher (Primary Contact), Philip Cox University of North Florida (UNF) 1 UNF Drive Jacksonville, FL 32224 Phone: (904) 620-1844 Email: jfletche@UNF.edu DOE Managers HQ: Donna Ho Phone: (202) 586-8000 Email: Donna.Ho@ee.doe.gov GO: Katie Randolph Phone: (720) 356-1759 Email: Katie.Randolph@go.doe.gov Contract Number: DE-EE0000475 Subcontractors: * University of Florida, Gainesville, FL * Northeastern University, Boston, MA * Johnson Matthey Fuel Cells, Swindon, UK

264

PON08010 American Recovery and Reinvestment Act of 2009 (ARRA) Cost Share: Alternative and Renewable Fuel and Vehicle Technology Program  

E-Print Network (OSTI)

PON08010 American Recovery and Reinvestment Act of 2009 (ARRA) Cost Share: Alternative Plug-In Hybrid Electric Vehicles (PHEVs) and Battery Electric Vehicles (BEVs). 15) A public entity and implementation of those vehicles. Will the budget breakdown include vehicle manufacturer costs involved? If so

265

Hydrogen and Infrastructure Costs  

NLE Websites -- All DOE Office Websites (Extended Search)

FUEL CELL TECHNOLOGIES PROGRAM Hydrogen and Infrastructure Costs Hydrogen Infrastructure Market Readiness Workshop Washington D.C. February 17, 2011 Fred Joseck U.S. Department of...

266

DOE Hydrogen and Fuel Cells Program Record 5038: Hydrogen Cost Competitive on a Cents per Mile Basis - 2006  

NLE Websites -- All DOE Office Websites (Extended Search)

8 Date: May 22, 2006 8 Date: May 22, 2006 Title: Hydrogen Cost Competitive on a Cents per Mile Basis - 2006 Originator: Patrick Davis & Steve Chalk Approved by: JoAnn Milliken Approval Date: May 22, 2006 Item : Lower the cost of hydrogen from natural gas to be competitive on a cents per mile basis with conventional gasoline vehicles. Supporting Information: The results of a 2003 economic analysis were used to estimate the cost of hydrogen produced from distributed natural gas reforming at $5 per gallon of gasoline equivalent (gge) (See U.S. DOE Record 5030: Hydrogen Baseline Cost of $5 per gge in 2003; available at http://www.hydrogen.energy.gov/program_records). Since the original analysis, DOE-sponsored R&D has resulted in significant cost reductions,

267

High Speed, Low Cost Fabrication of Gas Diffusion Electrodes for Membrane Electrode Assemblies - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

8 8 DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report Emory S. De Castro BASF Fuel Cell, Inc. 39 Veronica Avenue Somerset, NJ 08873 Phone: (732) 545-5100 ext 4114 Email: Emory.DeCastro@BASF.com DOE Managers HQ: Nancy Garland Phone: (202) 586-5673 Email: Nancy.Garland@ee.doe.gov GO: Jesse Adams Phone: (720) 356-1421 Email: Jesse.Adams@go.doe.gov Contract Number: DE-EE0000384 Subcontractor: Dr. Vladimir Gurau Case Western Reserve University, Cleveland, Ohio Project Start Date: July 1, 2009 Project End Date: June 30, 2013 Fiscal Year (FY) 2012 Objectives Reduce cost in fabricating gas diffusion electrodes * through the introduction of high speed coating technology, with a focus on materials used for the high- temperature membrane electrode assemblies (MEAs)

268

Development of a New Class of Low Cost, High Frequency Link Direct DC to AC Converters for Solid Oxide Fuel Cells (SOFC)  

SciTech Connect

This project proposes to design and develop a new class of power converters (direct DC to AC) to drastically improve performance and optimize the cost, size, weight and volume of the DC to AC converter in SOFC systems. The proposed topologies employ a high frequency link; direct DC to AC conversion approach. The direct DC to AC conversion approach is more efficient and operates without an intermediate dc-link stage. The absence of the dc-link, results in the elimination of bulky, aluminum electrolytic capacitors, which in turn leads to a reduction in the cost, volume, size and weight of the power electronic converter. The feasibility of two direct DC to AC converter topologies and their suitability to meet SECA objectives will be investigated. Laboratory proto-type converters (3-5kW) will be designed and tested in Phase-1. A detailed design trade-off study along with the test results will be available in the form of a report for the evaluation of SECA Industrial partners. This project proposes to develop a new and innovative power converter technology suitable for Solid Oxide Fuel Cell (SOFC) power systems in accordance with SECA objectives. The proposed fuel cell inverter (FCI) employs state of the art power electronic devices configured in two unique topologies to achieve direct conversion of DC power (24-48V) available from a SOFC to AC power (120/240V, 60Hz) suitable for utility interface and powering stand alone loads. The primary objective is to realize cost effective fuel cell converter, which operates under a wide input voltage range, and output load swings with high efficiency and improved reliability.

Prasad Enjeti; J.W. Howze

2003-12-01T23:59:59.000Z

269

Expanded production of labor-intensive crops increases agricultural employment  

E-Print Network (OSTI)

Specialist, Labor Market Information Division, Cali- forniaResearch Manager, Labor Market Information Di- vision, EDD.CES). Labor Market Information Division, Sacramento, CA.

Khan, Akhtar; Martin, Philip; Hardiman, Phil

2004-01-01T23:59:59.000Z

270

Colorado Department of Labor and Employment | Open Energy Information  

Open Energy Info (EERE)

Department of Labor and Employment Jump to: navigation, search Logo: Colorado Department of Labor and Employment Name Colorado Department of Labor and Employment Address 633 17th...

271

Solar Installation Labor Market Analysis  

NLE Websites -- All DOE Office Websites (Extended Search)

Installation Labor Installation Labor Market Analysis Barry Friedman National Renewable Energy Laboratory Philip Jordan Green LMI Consulting John Carrese San Francisco Bay Area Center of Excellence Technical Report NREL/TP-6A20-49339 December 2011 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 1617 Cole Boulevard Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Solar Installation Labor Market Analysis Barry Friedman National Renewable Energy Laboratory Philip Jordan Green LMI Consulting John Carrese San Francisco Bay Area Center of Excellence

272

Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009  

Gasoline and Diesel Fuel Update (EIA)

Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009 Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009 Oil and Gas Lease Equipment and Operating Costs 1994 Through 2009 Released: September 28, 2010 Next Release: Discontinued Excel Spreadsheet Model - 1994-2009 XLS (1,178 KB) Overview Oil and gas well equipment and operating costs, including coal bed methane costs, stopped their upward trend from the 1990s and fell sharply in 2009. The extremely high oil and gas prices during the first half of 2008 followed by an unprecedented drop to very low prices by the end of the year had a major impact on equipment demand. Operating costs tumbled also because fuel costs were reduced and well servicing rates fell in most areas. The exceptions were in California where electric rates continued to increase, causing a one (1) percent increase in annual operating costs for leases producing from 12,000 feet. Operating cost for coal bed methane wells in the Appalachian and Powder River areas increased because electric rates continued to climb. Due to the timing of the data collection, the cost reported here could be higher than the actual annual average for 2008. However, some production costs (labor and equipment) are not as volatile as drilling, pipe, and other well completion costs, so the effect of the oil and gas prices on collected data may be lessened. Annual average electric rates and natural gas prices are used, which also helps to dampen cost variances.

273

Cost Estimate for an Away-From-Reactor Generic Interim Storage Facility (GISF) for Spent Nuclear Fuel  

Science Conference Proceedings (OSTI)

As nuclear power plants began to run out of storage capacity in spent nuclear fuel (SNF) storage pools, many nuclear operating companies added higher density pool storage racks to increase pool capacity. Most nuclear power plant storage pools have been re-racked one or more times. As many spent fuel storage pools were re-racked to the maximum extent possible, nuclear operating companies began to employ interim dry storage technologies to store SNF in certified casks and canister-based systems outside of ...

2009-05-20T23:59:59.000Z

274

Recent Developments in California Labor Relations  

E-Print Network (OSTI)

BLS 2004b. The State of California Labor, Vol. 4, pp. 133–through the University of California Press’s Rights andPortrait. ” The State of California Labor 3: 3–37. Mitchell,

Mitchell, Daniel J. B.

2004-01-01T23:59:59.000Z

275

Oil and Gas Lease Equipment and Operating Costs 1994 Through...  

Gasoline and Diesel Fuel Update (EIA)

cost reported here could be higher than the actual annual average for 2008. However, some production costs (labor and equipment) are not as volatile as drilling, pipe, and other...

276

Federal Energy Management Program: Energy Cost Calculator for...  

NLE Websites -- All DOE Office Websites (Extended Search)

8000 hours Number of lamps in retrofit project Hours operating per week hours Average cost of electricity 0.06 kWh Relamper labor costs hr Time taken to retrofit all lamps...

277

Fusion reactor design studies: standard unit costs and cost scaling rules  

SciTech Connect

This report establishes standard unit costs and scaling rules for estimating costs of material, equipment, land, and labor components used in magnetic confinement fusion reactor plant construction and operation. Use of the standard unit costs and scaling rules will add uniformity to cost estimates, and thus allow valid comparison of the economic characteristics of various reactor concepts.

Schulte, S.C.; Bickford, W.E.; Willingham, C.E.; Ghose, S.K.; Walker, M.G.

1979-09-01T23:59:59.000Z

278

Hydrogen Threshold Cost Calculation  

NLE Websites -- All DOE Office Websites (Extended Search)

Program Record (Offices of Fuel Cell Technologies) Program Record (Offices of Fuel Cell Technologies) Record #: 11007 Date: March 25, 2011 Title: Hydrogen Threshold Cost Calculation Originator: Mark Ruth & Fred Joseck Approved by: Sunita Satyapal Date: March 24, 2011 Description: The hydrogen threshold cost is defined as the hydrogen cost in the range of $2.00-$4.00/gge (2007$) which represents the cost at which hydrogen fuel cell electric vehicles (FCEVs) are projected to become competitive on a cost per mile basis with the competing vehicles [gasoline in hybrid-electric vehicles (HEVs)] in 2020. This record documents the methodology and assumptions used to calculate that threshold cost. Principles: The cost threshold analysis is a "top-down" analysis of the cost at which hydrogen would be

279

Employee and Labor Relations | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Employee and Labor Relations Employee and Labor Relations Employee and Labor Relations The Headquarters Employee/Labor Relations Division provides labor/employee management relations advisory services to Headquarters staff, including union negotiations, adverse actions, grievances, and performance management. The Division staff represents management in third-party situations or union negotiations. Provides work life information, referral and support services to Headquarters employees covering such areas as child care, elder care, employee assistance programs, health and wellness, career transition and programs for the accessibility of Departmental services for people with disabilities. Click the "Contacts" Link to find a list of HR Specialist by the organization's they service.

280

Energy Department Invests Over $7 Million to Commercialize Cost...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Over 7 Million to Commercialize Cost-Effective Hydrogen and Fuel Cell Technologies Energy Department Invests Over 7 Million to Commercialize Cost-Effective Hydrogen and Fuel...

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

PEM Electrolyzer Incorporating an Advanced Low-Cost Membrane - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

1 1 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Monjid Hamdan (Primary Contact), Tim Norman Giner, Inc. (Formerly Giner Electrochemical Systems, LLC.) 89 Rumford Ave. Newton, MA 02466 Phone: (781) 529-0526 Email: mhamdan@ginerinc.com DOE Managers HQ: Erika Sutherland Phone: (202) 586-3152 Email: Erika.Sutherland@ee.doe.gov GO: David Peterson Phone: (720) 356-1747 Email: David.Peterson@go.doe.gov Contract Number: DE-FG36-08GO18065 Subcontractors: * Virginia Polytechnic Institute and University, Blacksburg, VA * Parker Hannifin Ltd domnick hunter Division, Hemel Hempstead, United Kingdom Project Start Date: May 1, 2008

282

High Performance, Low Cost Hydrogen Generation from Renewable Energy - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

5 5 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Dr. Katherine Ayers (Primary Contact), Andy Roemer Proton Energy Systems d/b/a Proton OnSite 10 Technology Drive Wallingford, CT 06492 Phone: (203) 678-2190 Email: kayers@protononsite.com DOE Managers HQ: Erika Sutherland Phone: (202) 586-3152 Email: Erika.Sutherland@ee.doe.gov GO: Dave Peterson Phone: (720) 356-1747 Email: David.Peterson@go.doe.gov Contract Number: DE-EE000276 Subcontractors: * Entegris, Inc., Chaska, MN * The Electrochemical Engine Center at Penn State, University Park, PA * Oak Ridge National Laboratory, Oak Ridge, TN Project Start Date: September 1, 2009

283

Power from the Fuel Cell  

E-Print Network (OSTI)

Power for Buildings Using Fuel-Cell Cars,” Proceedings ofwell as to drive down fuel-cell system costs through productis most likely to be the fuel-cell vehicle. Fuel cells are

Lipman, Timothy E.

2000-01-01T23:59:59.000Z

284

Alternative Fuels Data Center  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Connecticut Incentives and Laws Connecticut Incentives and Laws The following is a list of expired, repealed, and archived incentives, laws, regulations, funding opportunities, or other initiatives related to alternative fuels and vehicles, advanced technologies, or air quality. Hydrogen and Fuel Cell Promotion Archived: 08/31/2013 The Connecticut Center for Advanced Technology (CCAT), with funding from the Department of Economic and Community Development (DECD), has established a Connecticut Hydrogen-Fuel Cell Coalition (Coalition). The Coalition works to enhance economic growth through the development, manufacture, and deployment of fuel cell and hydrogen technologies and associated fueling systems. Representatives from industry, government, academia, labor, and other stakeholders make up the Coalition. CCAT

285

Multinational Firms and Heterogeneous Labor  

E-Print Network (OSTI)

In the presence of increasing specialization of workers it becomes more and more difficult for firms to find the most suitable ones. In such an environment a multinational enterprise (MNE) has an advantage because it can exchange workers between plants in different countries. Recruiting from the home and foreign plant leads to a larger labor market pool for an MNE, reducing the mismatch of its workforce. This paper analyzes the consequences of this advantage for production, employment, prices and wages. We find that the additional ability to recruit workers from the home and foreign labor market leads to lower mismatch, higher average productivity of workers, lower prices, higher output, and higher employment of a plant of an MNE as compared to a national firm, while the wage-effects depend on firm productivity. These facts are well in line with recent empirical findings.

Mario Larch; Wolfgang Lechthaler; Mario Larch; Wolfgang Lechthaler

2008-01-01T23:59:59.000Z

286

Solar Installation Labor Market Analysis  

DOE Green Energy (OSTI)

The potential economic benefits of the growing renewable energy sector have led to increased federal, state, and local investments in solar industries, including federal grants for expanded workforce training for U.S. solar installers. However, there remain gaps in the data required to understand the size and composition of the workforce needed to meet the demand for solar power. Through primary research on the U.S. solar installation employer base, this report seeks to address that gap, improving policymakers and other solar stakeholders understanding of both the evolving needs of these employers and the economic opportunity associated with solar market development. Included are labor market data covering current U.S. employment, expected industry growth, and employer skill preferences for solar installation-related occupations. This study offers an in-depth look at the solar installation sectors. A study published by the Solar Foundation in October 2011 provides a census of labor data across the entire solar value chain.

Friedman, B.; Jordan, P.; Carrese, J.

2011-12-01T23:59:59.000Z

287

Fuel Cells  

NLE Websites -- All DOE Office Websites (Extended Search)

Fuel Cells Fuel Cells Converting chemical energy of hydrogenated fuels into electricity Project Description Invented in 1839, fuels cells powered the Gemini and Apollo space missions, as well as the space shuttle. Although fuel cells have been successfully used in such applications, they have proven difficult to make more cost-effective and durable for commercial applications, particularly for the rigors of daily transportation. Since the 1970s, scientists at Los Alamos have managed to make various scientific breakthroughs that have contributed to the development of modern fuel cell systems. Specific efforts include the following: * Finding alternative and more cost-effective catalysts than platinum. * Enhancing the durability of fuel cells by developing advanced materials and

288

Hour-by-Hour Cost Modeling of Optimized Central Wind-Based Water Electrolysis Production - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

3 3 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Genevieve Saur (Primary Contact), Chris Ainscough. National Renewable Energy Laboratory (NREL) 15013 Denver West Parkway Golden, CO 80401-3305 Phone: (303) 275-3783 Email: genevieve.saur@nrel.gov DOE Manager HQ: Erika Sutherland Phone: (202) 586-3152 Email: Erika.Sutherland@ee.doe.gov Project Start Date: October 1, 2010 Project End Date: Project continuation and direction determined annually by DOE Fiscal Year (FY) 2012 Objectives Corroborate recent wind electrolysis cost studies using a * more detailed hour-by-hour analysis. Examine consequences of different system configuration * and operation for four scenarios, at 42 sites in five

289

Infrastructure Costs Associated with Central Hydrogen Production from Biomass and Coal - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

7 7 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Darlene Steward (Primary Contact), Billy Roberts, Karen Webster National Renewable Energy Laboratory (NREL) 15013 Denver West Parkway Golden, CO 80401-3305 Phone: (303) 275-3837 Email: Darlene.Steward@nrel.gov DOE Manager HQ: Fred Joseck Phone: (202) 586-7932 Email: Fred.Joseck@hq.doe.gov Project Start Date: Fiscal Year (FY) 2010 Project End Date: Project continuation and direction determined annually by DOE FY 2012 Objectives Elucidate the location-dependent variability of * infrastructure costs for biomass- and coal-based central hydrogen production and delivery and the tradeoffs inherent in plant-location choices Provide modeling output and correlations for use in other * integrated analyses and tools

290

Cost Study for Large Wind Turbine Blades  

SciTech Connect

The cost study for large wind turbine blades reviewed three blades of 30 meters, 50 meters, and 70 meters in length. Blade extreme wind design loads were estimated in accordance with IEC Class I recommendations. Structural analyses of three blade sizes were performed at representative spanwise stations assuming a stressed shell design approach and E-glass/vinylester laminate. A bill of materials was prepared for each of the three blade sizes using the laminate requirements prepared during the structural analysis effort. The labor requirements were prepared for twelve major manufacturing tasks. TPI Composites developed a conceptual design of the manufacturing facility for each of the three blade sizes, which was used for determining the cost of labor and overhead (capital equipment and facilities). Each of the three potential manufacturing facilities was sized to provide a constant annual rated power production (MW per year) of the blades it produced. The cost of the production tooling and overland transportation was also estimated. The results indicate that as blades get larger, materials become a greater proportion of total cost, while the percentage of labor cost is decreased. Transportation costs decreased as a percentage of total cost. The study also suggests that blade cost reduction efforts should focus on reducing material cost and lowering manufacturing labor, because cost reductions in those areas will have the strongest impact on overall blade cost.

ASHWILL, THOMAS D.

2003-05-01T23:59:59.000Z

291

Benchmarking Soft Costs for PV Systems in the United States (Presentation)  

SciTech Connect

This paper presents results from the first U.S. based data collection effort to quantify non-hardware, business process costs for PV systems at the residential and commercial scales, using a bottom-up approach. Annual expenditure and labor hour productivity data are analyzed to benchmark business process costs in the specific areas of: (1) customer acquisition; (2) permitting, inspection, and interconnection; (3) labor costs of third party financing; and (4) installation labor.

Ardani, K.

2012-06-01T23:59:59.000Z

292

Effects of Technology Cost Parameters on Hydrogen Pathway Succession - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

5 5 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Mark F. Ruth* (Primary Contact), Victor Diakov*, Brian James † , Julie Perez ‡ , Andrew Spisak † *National Renewable Energy Laboratory 15013 Denver West Pkwy. Golden, CO 80401 Phone: (303) 817-6160 Email: Mark.Ruth@nrel.gov and Victor.Diakov@nrel.gov † Strategic Analysis, Inc. ‡ New West Technologies DOE Manager HQ: Fred Joseck Phone: (202) 586-7932 Email: Fred.Joseck@ee.doe.gov Subcontractor: Strategic Analysis, Inc., Arlington, VA Project Start Date: February 1, 2009 Project End Date: October 31, 2011 Fiscal Year (FY) 2012 Objectives Develop a macro-system model (MSM): * Aimed at performing rapid cross-cutting analysis - Utilizing and linking other models - Improving consistency between models -

293

A Low-Cost Soft-Switched DC/DC Converter for Solid-Oxide Fuel Cells  

DOE Green Energy (OSTI)

A highly efficient DC to DC converter has been developed for low-voltage high-current solid oxide fuel cells. The newly developed 'V6' converter resembles what has been done in internal combustion engine that split into multiple cylinders to increase the output capacity without having to increase individual cell size and to smooth out the torque with interleaving operation. The development was started with topology overview to ensure that all the DC to DC converter circuits were included in the study. Efficiency models for different circuit topologies were established, and computer simulations were performed to determine the best candidate converter circuit. Through design optimization including topology selection, device selection, magnetic component design, thermal design, and digital controller design, a bench prototype rated 5-kW, with 20 to 50V input and 200/400V output was fabricated and tested. Efficiency goal of 97% was proven achievable through hardware experiment. This DC to DC converter was then modified in the later stage to converter 35 to 63 V input and 13.8 V output for automotive charging applications. The complete prototype was tested at Delphi with their solid oxide fuel cell test stand to verify the performance of the modified DC to DC converter. The output was tested up to 3-kW level, and the efficiency exceeded 97.5%. Multiple-phase interleaving operation design was proved to be reliable and ripple free at the output, which is desirable for the battery charging. Overall this is a very successful collaboration project between the SECA Core Technology Team and Industrial Team.

Jason Lai

2009-03-03T23:59:59.000Z

294

Use of plastic construction materials in small-scale fuel alcohol production  

Science Conference Proceedings (OSTI)

Several general designs for small-scale fuel alcohol plants that have been published primarily use conventional materials of construction (steel, copper, etc.). A fuel alcohol plant owned by Dixie Fuels, Inc. Valley Park, Mississippi, and a farm-scale alcohol plant being developed by the Tennessee Valley Authority have incorporated plastic materials in several areas of their plants; results have been excellent in terms of reduced materials, labor, and operating costs. However, plastics were not used in the distillation step. This work investigated the suitability of small-scale distillation equipment made entirely or partially from plastics. A low-cost alcohol distillation system can be constructed using chlorinated poly(viny chloride) (CPVC) pipe or poly(vinly chloride) (PVC) plastic pipe for the column and heat-exchanger shells. Although pipe made from CPVC is preferred, schedule 80 PVC pipe can be used if external supports are used to provide rigidity. 3 figures, 1 table. (DP)

Lightsey, G.R.; Kadir, O.

1982-01-01T23:59:59.000Z

295

Opportunities for Low Cost Titanium in Reduced Fuel Consumption, Improved Emissions, and Enhanced Durability Heavy Duty Vehicles  

DOE Green Energy (OSTI)

The purpose of this study was to determine which components of heavy-duty highway vehicles are candidates for the substitution of titanium materials for current materials if the cost of those Ti components is very significantly reduced from current levels. The processes which could be used to produce those low cost components were also investigated. Heavy-duty highway vehicles are defined as all trucks and busses included in Classes 2C through 8. These include heavy pickups and vans above 8,500 lbs. GVWR, through highway tractor trailers. Class 8 is characterized as being a very cyclic market, with ''normal'' year volume, such as in 2000, of approximately 240,000 new vehicles. Classes 3-7 are less cyclic, with ''normal'' i.e., year 2000, volume totaling approximately 325,000 new vehicles. Classes 3-8 are powered about 88.5% by diesel engines, and Class 2C at very roughly 83% diesel. The engine portion of the study therefore focused on diesels. Vehicle production volumes were used in estimates of the market size for candidate components.

Kraft, E.H.

2002-07-22T23:59:59.000Z

296

New High Performance Water Vapor Membranes to Improve Fuel Cell Balance of Plant Efficiency and Lower Costs (SBIR Phase I) - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

0 0 DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report Earl H. Wagener (Primary Contact), Brad P. Morgan, Jeffrey R. DiMaio Tetramer Technologies L.L.C. 657 S. Mechanic St. Pendleton, SC 29670 Phone: (864) 646-6282 Email: earl.wagener@tetramertechnologies.com DOE Manager HQ: Nancy Garland Phone: (202) 586-5673 Email: Nancy.Garland@ee.doe.gov Contract Number: DE-SC0006172 Project Start Date: June 17, 2011 Project End Date: March 16, 2012 Fiscal Year (FY) 2012 Objectives Demonstrate water vapor transport membrane with * >18,000 gas permeation units (GPU) Water vapor membrane with less than 20% loss in * performance after stress tests Crossover leak rate: <150 GPU * Temperature Durability of 90°C with excursions to * 100°C Cost of <$10/m

297

Hydrogen Pathway Cost Distributions  

NLE Websites -- All DOE Office Websites (Extended Search)

Pathway Cost Distributions Pathway Cost Distributions Jim Uihlein Fuel Pathways Integration Tech Team January 25, 2006 2 Outline * Pathway-Independent Cost Goal * Cost Distribution Objective * Overview * H2A Influence * Approach * Implementation * Results * Discussion Process * Summary 3 Hydrogen R&D Cost Goal * Goal is pathway independent * Developed through a well defined, transparent process * Consumer fueling costs are equivalent or less on a cents per mile basis * Evolved gasoline ICE and gasoline-electric hybrids are benchmarks * R&D guidance provided in two forms * Evolved gasoline ICE defines a threshold hydrogen cost used to screen or eliminate options which can't show ability to meet target * Gasoline-electric hybrid defines a lower hydrogen cost used to prioritize projects for resource allocation

298

Weatherization and Intergovernmental Program: Department of Labor  

NLE Websites -- All DOE Office Websites (Extended Search)

Program Guidance Program Guidance Site Map Printable Version Share this resource Send a link to Weatherization and Intergovernmental Program: Department of Labor Prevailing Wage Determinations for Weatherization Assistance Program (WAP) - Revised December 2009 to someone by E-mail Share Weatherization and Intergovernmental Program: Department of Labor Prevailing Wage Determinations for Weatherization Assistance Program (WAP) - Revised December 2009 on Facebook Tweet about Weatherization and Intergovernmental Program: Department of Labor Prevailing Wage Determinations for Weatherization Assistance Program (WAP) - Revised December 2009 on Twitter Bookmark Weatherization and Intergovernmental Program: Department of Labor Prevailing Wage Determinations for Weatherization Assistance Program

299

Analysis of the California Labor and Workforce Development Agency's Enforcement of Wage and Hour Laws  

E-Print Network (OSTI)

California Labor Market Information Division. Sacramento:Labor Agency’s Labor Market Information Division (LMID) andfrom the Labor Market Information Division, Employment

Ong, Paul M.; Rickles, Jordan

2004-01-01T23:59:59.000Z

300

Fuel Cells  

NLE Websites -- All DOE Office Websites (Extended Search)

Fuel Cells Fuel Cells The Solid State Energy Conversion Alliance (SECA) program is responsible for coordinating Federal efforts to facilitate development of a commercially relevant and robust solid oxide fuel cell (SOFC) system. Specific objectives include achieving an efficiency of greater than 60 percent, meeting a stack cost target of $175 per kW, and demonstrating lifetime performance degradation of less than 0.2 percent per

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Investigation of the viability and cost effectiveness of solid fuel gasifiers close coupled to internal combustion engines for 200 kWe power generation. Technical progress report No. 9  

DOE Green Energy (OSTI)

The viability and cost effectiveness of a 200 kWe engine generator unit fueled by a direct coupled, solid fuel gasifier were studied. Recent literature describing gasifier technology was obtained and personal visits were made to test facility sites and engine manufacturing plants to discuss the subject with researchers and engineers. Two prototype units were inspected, one of which was in partial operation. This report presents a brief discussion of fuel and gasifier technology, gas treatment (clean up) for engine use, engine use technology, other uses for gasifiers, the viability of close coupled units, and an estimate of cost effectiveness. Present small experimental gasifier systems perform as expected and have served to demonstrate the technology. Typically they operate with fuel species which are present and collected on the site of a processing plant. Certain needed development efforts are discussed. Also, fuel must be available at low cost and even then electric power produced in this way is unlikely to be competitive economically where utility poles are available. (LTN)

Mingle, J. G.; Junge, D. C.

1979-01-01T23:59:59.000Z

302

Education, Labor Markets and Technical  

E-Print Network (OSTI)

research on the obstacles and opportunities presented by the development of the Internet in Peru. Our research is organized by topic, but it is also possible to view it as three presentations: (1) Education, Labor Markets and Technical Capacity, (2) Creating Internet Opportunities, and (3) The Main Event-- RCP vs. Telefonica. We began our research by assessing the context of Peru in terms of geography, labor, and education. We attempted to understand the present technical capacity of the country as relevant to Internet development, and to estimate the ability of the population to realize that capacity. Next, we assess Peru's telecommunications policy, intellectual property protection, and sources of financing for potential Internet ventures. We briefly cover the history of telecommunications policy in Peru, as well as more recent reform legislation. Throughout our analysis, one of the most interesting actors is the non-profit Red Cientifica Peruana (RCP). In the latter part of our analysis, we contrast the progressive vision of RCP with the financial and organizational might of the dominant telecommunications carrier, Telefonica del Peru, a former state-owned monopoly. Finally, we present overall conclusions on this topic.

unknown authors

1999-01-01T23:59:59.000Z

303

AVCEM: Advanced-Vehicle Cost and Energy Use Model  

E-Print Network (OSTI)

of the battery, according to the battery cost equations (seediscussion of battery cost above). There actually are twoin the amount and cost of fuel-storage, battery, vehicle

Delucchi, Mark

2005-01-01T23:59:59.000Z

304

Biodiesel Performance, Costs, and Use  

U.S. Energy Information Administration (EIA)

Biodiesel Performance, Costs, and Use. by Anthony Radich. Introduction. The idea of using vegetable oil for fuel has been around as long as the diesel engine.

305

Vehicle Cost Calculator  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Electric Plug-in Hybrid Electric Natural Gas (CNG) Flex Fuel (E85) Biodiesel (B20) Next Vehicle Cost Calculator U.S. Department of Energy Energy Efficiency and Renewable Energy...

306

Governance of labor in digital video networks  

Science Conference Proceedings (OSTI)

Theories of digitally distributed labor tend to fall into an idealized, oppositional binary that conflates digital labor systems with critiques that are judgmental rather than based on detailed analyses of the actual system or site. On the one hand are ... Keywords: algorithm, beta, crowdsourcing, digital, governance, internet, technology, television, video

Adam Fish

2011-02-01T23:59:59.000Z

307

14.661 Labor Economics I, Fall 2006  

E-Print Network (OSTI)

Neoclassical analysis of the labor market and its institutions. A systematic development of the theory of labor supply, labor demand, and human capital. Topics discussed also include wage and employment determination, ...

Pischke, Jorn-Steffen

308

Essays in labor economics and the economics of education  

E-Print Network (OSTI)

1998. “Employee Labor Market Information: Comparing DirectHow Does Poor Labor-Market Information Affect Wages? The44 Table 1.8: Labor-Market Information and Job Tenure,

Thomas, Jaime Lynn

2010-01-01T23:59:59.000Z

309

Utah Labor Commission | Open Energy Information  

Open Energy Info (EERE)

Labor Commission Labor Commission Jump to: navigation, search Name Utah Labor Commission Address 160 East 300 South, 3rd Floor Place Salt Lake City, Utah Zip 84114-6600 Phone number (801) 530-6800 Website http://laborcommission.utah.go References Website[1] This article is a stub. You can help OpenEI by expanding it. Utah Labor Commission is an organization based in Salt Lake City, Utah. The Utah Labor Commission is the regulatory agency responsible for preserving the balance established by the legislature for protecting the health, safety, and economic well-being of employees and employers. It is a multi-division state agency directed by a Commissioner who is appointed by the Governor. The Commissioner oversees the various functions of the divisions within the Commission.

310

Hawaii Department of Labor and Industrial Relations Occupational...  

Open Energy Info (EERE)

Labor and Industrial Relations Occupational Safety and Health Division Jump to: navigation, search Name Hawaii Department of Labor and Industrial Relations Occupational Safety and...

311

WEDNESDAY: Energy Secretary Chu and Labor Secretary Solis to...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Secretary Chu and Labor Secretary Solis to Discuss Clean Energy Jobs in Nevada WEDNESDAY: Energy Secretary Chu and Labor Secretary Solis to Discuss Clean Energy Jobs in...

312

Chapter 22 - Labor Standards for Construction | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Chapter 22 - Labor Standards for Construction Chapter 22.1 - Labor Standards More Documents & Publications Acquisition Guide Flash2004-21.pdf OPAM Policy Acquisition Guides...

313

Fuel Guide Economy  

NLE Websites -- All DOE Office Websites (Extended Search)

1 1 MODEL YEAR 2000 FUEL ECONOMY LEADERS IN POPULAR VEHICLE CLASSES Listed below are the vehicles with the highest fuel economy for the most popular classes, including both automatic and manual transmissions and gasoline and diesel vehicles. Please be aware that many of these vehicles come in a range of engine sizes and trim lines, resulting in different fuel economy values. Check the fuel economy guide or the fuel economy sticker on new vehicles to find the values for a particular version of a vehicle. CONTENTS MODEL YEAR 2000 FUEL ECONOMY LEADERS ................. 1 HOW TO USE THIS GUIDE ..................................................... 2 FUEL ECONOMY AND YOUR ANNUAL FUEL COSTS .......... 3 WHY FUEL ECONOMY IS IMPORTANT .................................

314

Fuel Cell Power Model Elucidates Life-Cycle Costs for Fuel Cell-Based Combined Heat, Hydrogen, and Power (CHHP) Production Systems (Fact Sheet), Hydrogen and Fuel Cell Technical Highlights (HFCTH)  

NLE Websites -- All DOE Office Websites (Extended Search)

3 * November 2010 3 * November 2010 Electricity Natural Gas Power Heat Natural Gas or Biogas Tri-Generation Fuel Cell Hydrogen Natural Gas Converted to hydrogen on site via steam-methane reforming electrolyzer peak burner heat sink FC SYSTEM + H 2 Renewables H 2 -FC H 2 -storage 0 2 4 6 8 10 12 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Electricity Demand (kW) Heat Demand (kW) Hydrogen Demand (kW) 0 2 4 6 8 10 12 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Electricity Demand (kW) Heat Demand (kW) Hydrogen Demand (kW) 0 2 4 6 8 10 12 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Electricity Demand (kW) Heat Demand (kW) Hydrogen Demand (kW) 0 2 4 6 8 10 12 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Electricity Demand (kW) Heat Demand (kW) Hydrogen Demand (kW) * Grid electricity (hourly) * Fuel prices * Water price 0 2 4

315

The Social-Cost Calculator (SCC): Documentation of Methods and Data, and Case Study of Sacramento  

E-Print Network (OSTI)

N. I. Tishchcishyna, Costs of Oil Dependence: A 2000 Update,costs • Climate change costs • Oil use costs • Fuel costs •sections on climate-change costs, oil-use external costs,

Delucchi, Mark

2005-01-01T23:59:59.000Z

316

THE SOCIAL-COST CALCULATOR (SCC): DOCUMENTATION OF METHODS AND DATA, AND CASE STUDY OF SACRAMENTO  

E-Print Network (OSTI)

N. I. Tishchcishyna, Costs of Oil Dependence: A 2000 Update,costs • Climate change costs • Oil use costs • Fuel costs •sections on climate-change costs, oil-use external costs,

Delucchi, Mark

2005-01-01T23:59:59.000Z

317

Production costs and supply of biomass by U.S. Region  

DOE Green Energy (OSTI)

The Biofuels Feedstock Development Program has attempted to estimate the cost of producing dedicated energy crops for several regions of the United States. Switchgrass and hybrid poplar have been chosen as representative herbaceous and woody crop species for the estimation. A full economic cost accounting approach is used. This means that not only are out-of-pocket cash expenses (e.g. fertilizers, chemicals, seeds, fuel, repairs) estimated, but fixed costs (e.g., overhead, taxes) and the costs of owned resources (e.g., producer`s own labor, equipment depreciation, land values) are also estimated as part of the cost of producing dedicated energy crops. The costs are estimated as enterprise budgets which means that costs of producing energy crops are estimated as separate entities, and not estimated in context of the entire farm management structure. Competitiveness of energy crops with conventional crops vary by region. Breakeven prices are regional averages. Breakeven prices for poplar are higher than for switchgrass in all regions, in large part due to the higher cost of producing poplars.

Walsh, M.

1995-07-01T23:59:59.000Z

318

The Guy at the Controls Labor Quality and Power Plant Efficiency  

E-Print Network (OSTI)

In this chapter, we explore the impact of labor policies on the operations of electric power plants. At first glance, it might seem that workers should have little scope to influence the performance of the electricity industry and that this should be particularly true of the generation sector, where costs are

Richard B. Freeman; Kathryn L. Shaw; James B. Bushnell; Catherine Wolfram

2006-01-01T23:59:59.000Z

319

Requirements for low cost electricity and hydrogen fuel production from multi-unit intertial fusion energy plants with a shared driver and target factory  

E-Print Network (OSTI)

reducing USdependenceon foreign oil imports, the associatedor, as they do fuel now,to foreign oil producers, assuming

Logan, B. Grant; Moir, Ralph; Hoffman, Myron A.

1994-01-01T23:59:59.000Z

320

Solar energy commercialization and the labor market  

SciTech Connect

The success of a new technology does not depend only on its technical and economic feasibility. Evidence from the diffusion of non-solar technologies suggests that unless the product can be accepted and integrated into existing institutional processes and practices and can meet specific user and technology delivery system requirements, acceptance and diffusion of the technology will be slow. This paper discusses the potential impacts of solar energy commercialization on labor demand, and conversely, the potential impacts of the labor supply system on solar energy commercialization. Various participants in manpower training programs are examined, and alternative implementation channels to meet the labor needs of an emerging technology are discussed.

Mason, B.; Ferris, G.; Burns, B.

1978-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

The Guy at the Controls: Labor Quality and Power Plant Efficiency  

E-Print Network (OSTI)

This paper examines the impact of individual human operators on the fuel efficiency of power plants. Although electricity generation is a fuel and capital intensive enterprise, anecdotal evidence, interviews, and empirical analysis support the hypothesis that labor, particularly power plant operators, can have a non-trivial impact on the operating efficiency of the plant. We present evidence to demonstrate these effects and survey the policies and practices of electricity producing rms that either reduce or exacerbate fuel efficiency differences across individual plant operators.

James B. Bushnell; Catherine Wolfram

2007-01-01T23:59:59.000Z

322

Pilot-Scale Demonstration of a Novel, Low-Cost Oxygen Supply Process and its Integration with Oxy-Fuel Coal-Fired Boilers  

Science Conference Proceedings (OSTI)

In order to achieve DOE targets for carbon dioxide capture, it is crucial not only to develop process options that will generate and provide oxygen to the power cycle in a cost-effective manner compared to the conventional oxygen supply methods based on cryogenic air separation technology, but also to identify effective integration options for these new technologies into the power cycle with carbon dioxide capture. The Linde/BOC developed Ceramic Autothermal Recovery (CAR) process remains an interesting candidate to address both of these issues by the transfer of oxygen from the air to a recycled CO{sub 2} rich flue-gas stream in a cyclic process utilizing the high temperature sorption properties of perovskites. Good progress was made on this technology in this project, but significant challenges remain to be addressed before CAR oxygen production technology is ready for commercial exploitation. Phase 1 of the project was completed by the end of September 2008. The two-bed 0.7 tons/day O2 CAR process development unit (PDU) was installed adjacent to WRI's pilot scale coal combustion test facility (CTF). Start-up and operating sequences for the PDU were developed and cyclic operation of the CAR process demonstrated. Controlled low concentration methane addition allowed the beds to be heated up to operational temperature (800-900 C) and then held there during cyclic operation of the 2-bed CAR process, in this way overcoming unavoidable heat losses from the beds during steady state operation. The performance of the PDU was optimized as much as possible, but equipment limitations prevented the system from fully achieving its target performance. Design of the flue gas recirculation system to integrate CAR PDU with the CTF and the system was completed and integrated tests successfully performed at the end of the period. A detailed techno-economic analysis was made of the CAR process for supplying the oxygen in oxy-fuel combustion retrofit option using AEP's 450 MW Conesville, Ohio plant and contrasted with the cryogenic air separation option (ASU). Design of a large scale CAR unit was completed to support this techno-economic assessment. Based on the finding that the overall cost potential of the CAR technology compared to cryogenic ASU is nominal at current performance levels and that the risks related to both material and process scale up are still significant, the team recommended not to proceed to Phase 2. CAR process economics continue to look attractive if the original and still 'realistic' target oxygen capacities could be realized in practice. In order to achieve this end, a new fundamental materials development program would be needed. With the effective oxygen capacities of the current CAR materials there is, however, insufficient economic incentive to use this commercially unproven technology in oxy-fuel power plant applications in place of conventional ASUs. In addition, it is now clear that before a larger scale pilot demonstration of the CAR technology is made, a better understanding of the impact of flue-gas impurities on the CAR materials and of thermal transients in the beds is required.

Krish Krishnamurthy; Divy Acharya; Frank Fitch

2008-09-30T23:59:59.000Z

323

Liquid Fuels Market Model of the National Energy Modeling ...  

U.S. Energy Information Administration (EIA)

The outside battery-limit (OSBL) costs include the cost of cooling water, steam and electric power generation and distribution, fuel oil and fuel gas ...

324

Essays in public finance and labor economics  

E-Print Network (OSTI)

This thesis examines three questions of causality relevant to public finance and labor economics: the effect of racial segregation on city characteristics, the effect of divorce on women's economic outcomes, and the effect ...

Ananat, Elizabeth Oltmans

2006-01-01T23:59:59.000Z

325

Evaluating the Energy Use of Labor  

NLE Websites -- All DOE Office Websites (Extended Search)

Evaluating the Energy Use of Labor Evaluating the Energy Use of Labor Speaker(s): Teresa W. Zhang Date: April 20, 2007 - 12:00pm Location: 90-3122 Seminar Host/Point of Contact: Richard Diamond Energy use is an important metric of environmental impact and manufacturing efficiency. However, a major component of energy analysis has yet to permeate life-cycle analysis methodology: the energy use associated with human labor. We will discuss a straightforward method of estimating the energy demands of an hour of industrial labor based on readily available national statistics. In the United States, this estimate yields 30 MJ of primary energy use per worker-hour (EPWH). These results can be applied to inform an expand the applications of process-based and hybrid economic input-output life-cycle assessment

326

Fermilab | Fermilab Time and Labor | Launch  

NLE Websites -- All DOE Office Websites (Extended Search)

Go to FTL timecard Click here to create and submit your timecard on the Fermilab Time and Labor system. Alternate System Login This link uses html only and may work on your mobile device. It is provided for ease of use only. If it doesn't work for you, please use the other link. Fermilab Time and Labor All employees use a single, standard system to report their time and effort electronically. Log in to the system here. This has modernized our time and labor reporting system and helps Fermilab comply with DOE requirements. Use this page to access tools that will help you use the Fermilab Time & Labor electronic timecard. You can login to your timecard, access training materials and documentation and ensure that your browser has the settings and software it needs to access the system.

327

Flexible Bureaucracies in Labor Market Regulation  

E-Print Network (OSTI)

This paper compares and contrasts the U.S. and French systems of labor market regulation. The U.S. system is specialized: Regulating authority is dispersed among a host of different agencies each with a relatively narrow ...

Piore, Michael J.

328

Modeling of Cost Curves 1.0 Costs of Generating Electrical Energy  

E-Print Network (OSTI)

production costs. Some typical average costs of fuel are given in the following table for coal, petroleum [1] Petroleum [2] Natural Gas [3] All Fossil Fuels Receipts (Billion BTU) Average Cost Avg. Sulfur fuel, kerosene, petroleum coke (converted to liquid petroleum, see Technical Notes for conversion

McCalley, James D.

329

Home-based work, human capital accumulation and women's labor force participation  

E-Print Network (OSTI)

This dissertation examines the effect of changes in the stock of human capital on the labor force participation decision of women aged 25-54. Without the option of homebased work, some women choose to leave the labor market and stay at home temporarily for family reasons. Working women realize that time out of the labor force could impose penalties on their work careers. This is because during the break, they do not accumulate any new human capital while the existing job skills continuously depreciate. Nowadays, home-based work becomes possible for many jobs because rapid development in personal computers and advances in information and communications technology have reduced employers� cost of offering home-based work arrangements. Working women can resolve the time conflict between demand for paid work and family responsibility by working from home. In a previous study, the home-based work decision depends on the fixed cost of working and potential home production. Women who are disabled, have small children, or live in rural areas are likely to work from home because they have high fixed costs of working and high potential home production. However, none of the existing studies applies the human capital theory of labor supply to the home-based work decision. Using data on the female labor force from the Integrated Public Use Microdata Series (IPUMS) of housing units from the 2000 U.S. Census, I estimate a nested logit model to examine the effects of expected costs of non-participation, in terms of forgone earnings, forgone human capital accumulation and human capital depreciation, on women�s labor force participation decision. I find that, other things being equal, women aged 25 to 44 who have potentially high human capital accumulation and high human capital depreciation are likely to stay in the labor force. In the case that the value of their home time is so high that they choose to stay at home, they prefer to work for pay at home than to be out of the labor force.

Chutubtim, Piyaluk

2005-08-01T23:59:59.000Z

330

Estimating decommissioning costs: The 1994 YNPS decommissioning cost study  

Science Conference Proceedings (OSTI)

Early this year, Yankee Atomic Electric Company began developing a revised decommissioning cost estimate for the Yankee Nuclear Power Station (YNPS) to provide a basis for detailed decommissioning planning and to reflect slow progress in siting low-level waste (LLW) and spent-nuclear-fuel disposal facilities. The revision also reflects the need to change from a cost estimate that focuses on overall costs to a cost estimate that is sufficiently detailed to implement decommissioning and identify the final cost of decommissioning.

Szymczak, W.J.

1994-12-31T23:59:59.000Z

331

Processing Cost Analysis for Biomass Feedstocks  

DOE Green Energy (OSTI)

The receiving, handling, storing, and processing of woody biomass feedstocks is an overlooked component of biopower systems. The purpose of this study was twofold: (1) to identify and characterize all the receiving, handling, storing, and processing steps required to make woody biomass feedstocks suitable for use in direct combustion and gasification applications, including small modular biopower (SMB) systems, and (2) to estimate the capital and operating costs at each step. Since biopower applications can be varied, a number of conversion systems and feedstocks required evaluation. In addition to limiting this study to woody biomass feedstocks, the boundaries of this study were from the power plant gate to the feedstock entry point into the conversion device. Although some power plants are sited at a source of wood waste fuel, it was assumed for this study that all wood waste would be brought to the power plant site. This study was also confined to the following three feedstocks (1) forest residues, (2) industrial mill residues, and (3) urban wood residues. Additionally, the study was confined to grate, suspension, and fluidized bed direct combustion systems; gasification systems; and SMB conversion systems. Since scale can play an important role in types of equipment, operational requirements, and capital and operational costs, this study examined these factors for the following direct combustion and gasification system size ranges: 50, 20, 5, and 1 MWe. The scope of the study also included: Specific operational issues associated with specific feedstocks (e.g., bark and problems with bridging); Opportunities for reducing handling, storage, and processing costs; How environmental restrictions can affect handling and processing costs (e.g., noise, commingling of treated wood or non-wood materials, emissions, and runoff); and Feedstock quality issues and/or requirements (e.g., moisture, particle size, presence of non-wood materials). The study found that over the years the industry has shown a good deal of ingenuity and, as a result, has developed several cost effective methods of processing and handling wood. SMB systems usually cannot afford to perform much onsite processing and therefore usually purchase fuels processed to specification. Owners of larger systems try to minimize onsite processing to minimize processing costs. Whole truck dumpers are expensive, but allow for faster and easier unloading, which reduces labor costs and charges by the haulers. Storage costs are a major factor in overall costs, thus the amount of fuel reserve is an important consideration. Silos and bins are relatively expensive compared to open piles used for larger facilities, but may be required depending on space available, wood characteristics, and amount of wood to be stored. For larger systems, a front-end loader has a lot of flexibility in use and is an essential piece of equipment for moving material. Few opportunities appear to exist for improving the cost effectiveness of these systems.

Badger, P.C.

2002-11-20T23:59:59.000Z

332

I. Notification of Employee Rights Under the National Labor Relations Act. Case 2010-006  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

List of Rules in FAC 2005-54 List of Rules in FAC 2005-54 I. Notification of Employee Rights Under the National Labor Relations Act. Case 2010-006 II. Preventing Personal Conflicts of Interest for Contractor Employees Performing Acquisition Functions Case 2008-025 III. Small Disadvantaged Business Program Self-Certification Case 2009-019. IV. Certification Requirement and Procurement Prohibition Relating to Iran Sanctions Case 2010-018 V. Representation Regarding Export of Sensitive Technology to Iran (Interim)Case 2010- 024 VI. Set-Asides for Small Business (Interim) Case 2011-024 VII. Sudan Waiver Process.Case 2009-041 VIII. Successor Entities to the Netherlands Antilles Case 2011-014 IX. Labor Relations Costs Case 2009-006 IX. Technical Amendments Item I--Notification of Employee Rights Under the National Labor Relations Act (FAR Case

333

Assessment of costs and benefits of flexible and alternative fuel use in the U.S. transportation sector. Technical report fourteen: Market potential and impacts of alternative fuel use in light-duty vehicles -- A 2000/2010 analysis  

DOE Green Energy (OSTI)

In this report, estimates are provided of the potential, by 2010, to displace conventional light-duty vehicle motor fuels with alternative fuels--compressed natural gas (CNG), liquefied petroleum gas (LPG), methanol from natural gas, ethanol from grain and from cellulosic feedstocks, and electricity--and with replacement fuels such as oxygenates added to gasoline. The 2010 estimates include the motor fuel displacement resulting both from government programs (including the Clean Air Act and EPACT) and from potential market forces. This report also provides an estimate of motor fuel displacement by replacement and alterative fuels in the year 2000. However, in contrast to the 2010 estimates, the year 2000 estimate is restricted to an accounting of the effects of existing programs and regulations. 27 figs., 108 tabs.

NONE

1996-01-01T23:59:59.000Z

334

Advanced Proliferation Resistant, Lower Cost, Uranium-Thorium Dioxide Fuels for Light Water Reactors (Progress report for work through June 2002, 12th quarterly report)  

SciTech Connect

The overall objective of this NERI project is to evaluate the potential advantages and disadvantages of an optimized thorium-uranium dioxide (ThO2/UO2) fuel design for light water reactors (LWRs). The project is led by the Idaho National Engineering and Environmental Laboratory (INEEL), with the collaboration of three universities, the University of Florida, Massachusetts Institute of Technology (MIT), and Purdue University; Argonne National Laboratory; and all of the Pressurized Water Reactor (PWR) fuel vendors in the United States (Framatome, Siemens, and Westinghouse). In addition, a number of researchers at the Korean Atomic Energy Research Institute and Professor Kwangheon Park at Kyunghee University are active collaborators with Korean Ministry of Science and Technology funding. The project has been organized into five tasks: · Task 1 consists of fuel cycle neutronics and economics analysis to determine the economic viability of various ThO2/UO2 fuel designs in PWRs, · Task 2 will determine whether or not ThO2/UO2 fuel can be manufactured economically, · Task 3 will evaluate the behavior of ThO2/UO2 fuel during normal, off-normal, and accident conditions and compare the results with the results of previous UO2 fuel evaluations and U.S. Nuclear Regulatory Commission (NRC) licensing standards, · Task 4 will determine the long-term stability of ThO2/UO2 high-level waste, and · Task 5 consists of the Korean work on core design, fuel performance analysis, and xenon diffusivity measurements.

Mac Donald, Philip Elsworth

2002-09-01T23:59:59.000Z

335

Alternative Fuels Data Center: Hydrogen Fuel Infrastructure Tax Credit  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Hydrogen Fuel Hydrogen Fuel Infrastructure Tax Credit to someone by E-mail Share Alternative Fuels Data Center: Hydrogen Fuel Infrastructure Tax Credit on Facebook Tweet about Alternative Fuels Data Center: Hydrogen Fuel Infrastructure Tax Credit on Twitter Bookmark Alternative Fuels Data Center: Hydrogen Fuel Infrastructure Tax Credit on Google Bookmark Alternative Fuels Data Center: Hydrogen Fuel Infrastructure Tax Credit on Delicious Rank Alternative Fuels Data Center: Hydrogen Fuel Infrastructure Tax Credit on Digg Find More places to share Alternative Fuels Data Center: Hydrogen Fuel Infrastructure Tax Credit on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Hydrogen Fuel Infrastructure Tax Credit A tax credit is available for the cost of hydrogen fueling equipment placed

336

Assessment of costs and benefits of flexible and alternative fuel use in the US transportation sector. Technical report twelve: Economic analysis of alternative uses for Alaskan North Slope natural gas  

DOE Green Energy (OSTI)

As part of the Altemative Fuels Assessment, the Department of Energy (DOE) is studying the use of derivatives of natural gas, including compressed natural gas and methanol, as altemative transportation fuels. A critical part of this effort is determining potential sources of natural gas and the economics of those sources. Previous studies in this series characterized the economics of unutilized gas within the lower 48 United States, comparing its value for methanol production against its value as a pipelined fuel (US Department of Energy 1991), and analyzed the costs of developing undeveloped nonassociated gas reserves in several countries (US Department of Energy 1992c). This report extends those analyses to include Alaskan North Slope natural gas that either is not being produced or is being reinjected. The report includes the following: A description of discovered and potential (undiscovered) quantities of natural gas on the Alaskan North Slope. A discussion of proposed altemative uses for Alaskan North Slope natural gas. A comparison of the economics of the proposed alternative uses for Alaskan North Slope natural gas. The purpose of this report is to illustrate the costs of transporting Alaskan North Slope gas to markets in the lower 48 States as pipeline gas, liquefied natural gas (LNG), or methanol. It is not intended to recommend one alternative over another or to evaluate the relative economics or timing of using North Slope gas in new tertiary oil recovery projects. The information is supplied in sufficient detail to allow incorporation of relevant economic relationships (for example, wellhead gas prices and transportation costs) into the Altemative Fuels Trade Model, the analytical framework DOE is using to evaluate various policy options.

Not Available

1993-12-01T23:59:59.000Z

337

Joint Fuel Cell Bus Workshop Summary Report  

NLE Websites -- All DOE Office Websites (Extended Search)

equipment is heavy and costly * Slow response time of the fuel cell adversely affects regenerative energy recovery potential and efficiency Barriers to full fuel cell bus...

338

Manufacturing Cost Analysis of Novel Steel/Concrete Composite Vessel for Stationary Storage of High-Pressure Hydrogen  

SciTech Connect

A novel, low-cost, high-pressure, steel/concrete composite vessel (SCCV) technology for stationary storage of compressed gaseous hydrogen (CGH2) is currently under development at Oak Ridge National Laboratory (ORNL) sponsored by DOE s Fuel Cell Technologies (FCT) Program. The SCCV technology uses commodity materials including structural steels and concretes for achieving cost, durability and safety requirements. In particular, the hydrogen embrittlement of high-strength low-alloy steels, a major safety and durability issue for current industry-standard pressure vessel technology, is mitigated through the use of a unique layered steel shell structure. This report presents the cost analysis results of the novel SCCV technology. A high-fidelity cost analysis tool is developed, based on a detailed, bottom-up approach which takes into account the material and labor costs involved in each of the vessel manufacturing steps. A thorough cost study is performed to understand the SCCV cost as a function of the key vessel design parameters, including hydrogen pressure, vessel dimensions, and load-carrying ratio. The major conclusions include: The SCCV technology can meet the technical/cost targets set forth by DOE s FCT Program for FY2015 and FY2020 for all three pressure levels (i.e., 160, 430 and 860 bar) relevant to the hydrogen production and delivery infrastructure. Further vessel cost reduction can benefit from the development of advanced vessel fabrication technologies such as the highly automated friction stir welding (FSW). The ORNL-patented multi-layer, multi-pass FSW can not only reduce the amount of labor needed for assembling and welding the layered steel vessel, but also make it possible to use even higher strength steels for further cost reductions and improvement of vessel structural integrity. It is noted the cost analysis results demonstrate the significant cost advantage attainable by the SCCV technology for different pressure levels when compared to the industry-standard pressure vessel technology. The real-world performance data of SCCV under actual operating conditions is imperative for this new technology to be adopted by the hydrogen industry for stationary storage of CGH2. Therefore, the key technology development effort in FY13 and subsequent years will be focused on the fabrication and testing of SCCV mock-ups. The static loading and fatigue data will be generated in rigorous testing of these mock-ups. Successful tests are crucial to enabling the near-term impact of the developed storage technology on the CGH2 storage market, a critical component of the hydrogen production and delivery infrastructure. In particular, the SCCV has high potential for widespread deployment in hydrogen fueling stations.

Feng, Zhili [ORNL; Zhang, Wei [ORNL; Wang, Jy-An John [ORNL; Ren, Fei [ORNL

2012-09-01T23:59:59.000Z

339

Requirements for low cost electricity and hydrogen fuel production from multi-unit intertial fusion energy plants with a shared driver and target factory  

E-Print Network (OSTI)

steam generators (SG),steam turbines(T), generators andawith the costs of modern steam turbine generator plants forSteam generators Remote maintenance equipment Turbine plant

Logan, B. Grant; Moir, Ralph; Hoffman, Myron A.

1994-01-01T23:59:59.000Z

340

High-burnup fuel and the impact on fuel management  

SciTech Connect

Competition in the electric utility industry has forced utilities to reduce cost. For a nuclear utility, this means a reduction of both the nuclear fuel cost and the operating and maintenance cost. To this extent, utilities are pursuing longer cycles. To reduce the nuclear fuel cost, utilities are trying to reduce batch size while increasing cycle length. Yankee Atomic Electric Company has performed a number of fuel cycle studies to optimize both batch size and cycle length; however, certain burnup-related constraints are encountered. As a result of these circumstances, longer fuel cycles make it increasingly difficult to simultaneously meet the burnup-related fuel design constraints and the technical specification limits. Longer cycles require fuel assemblies to operate for longer times at relatively high power. If utilities continue to pursue longer cycles to help reduce nuclear fuel cost, changes may need to be made to existing fuel burnup limits.

Cacciapouti, R.J.; Weader, R.J. [Yankee Atomic Electric Co., Bolton, MA (United States)

1996-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Fuel gas production from animal residue. Dynatech report No. 1551  

DOE Green Energy (OSTI)

A comprehensive mathematical model description of anaerobic digestion of animal residues was developed, taking into account material and energy balances, kinetics, and economics of the process. The model has the flexibility to be applicable to residues from any size or type of animal husbandry operation. A computer program was written for this model and includes a routine for optimization to minimum unit gas cost, with the optimization variables being digester temperature, retention time, and influent volatile solids concentration. The computer program was used to determine the optimum base-line process conditions and economics for fuel gas production via anaerobic digestion of residues from a 10,000 head environmental beef feedlot. This feedlot at the conditions for minimum unit gas cost will produce 300 MCF/day of methane at a cost of $5.17/MCF (CH/sub 4/), with a total capital requirement of $1,165,000, a total capital investment of $694,000, and an annual average net operating cost of $370,000. The major contributions to this unit gas cost are due to labor (37 percent), raw manure (11 percent), power for gas compression (10 percent), and digester cost (13 percent). A conceptual design of an anaerobic digestion process for the baseline conditions is presented. A sensitivity analysis of the unit gas cost to changes in the major contributions to unit gas cost was performed, and the results of this analysis indicate areas in the anaerobic digestion system design where reasonable improvements could be expected so as to produce gas at an economically feasible cost. This sensitivity analysis includes the effects on unit gas cost of feedlot size and type, digester type, digester operating conditions, and economic input data.

Ashare, E.; Wise, D.L.; Wentworth, R.L.

1977-01-14T23:59:59.000Z

342

Alternative Fuels Data Center: Renewable Fuel Infrastructure Tax Credit  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Renewable Fuel Renewable Fuel Infrastructure Tax Credit to someone by E-mail Share Alternative Fuels Data Center: Renewable Fuel Infrastructure Tax Credit on Facebook Tweet about Alternative Fuels Data Center: Renewable Fuel Infrastructure Tax Credit on Twitter Bookmark Alternative Fuels Data Center: Renewable Fuel Infrastructure Tax Credit on Google Bookmark Alternative Fuels Data Center: Renewable Fuel Infrastructure Tax Credit on Delicious Rank Alternative Fuels Data Center: Renewable Fuel Infrastructure Tax Credit on Digg Find More places to share Alternative Fuels Data Center: Renewable Fuel Infrastructure Tax Credit on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Renewable Fuel Infrastructure Tax Credit A tax credit is available for 25% of the cost to install or retrofit

343

DOE Hydrogen Analysis Repository: PEMFC Manufacturing Cost  

NLE Websites -- All DOE Office Websites (Extended Search)

PEMFC Manufacturing Cost PEMFC Manufacturing Cost Project Summary Full Title: Manufacturing Cost of Stationary Polymer Electrolyte Membrane (PEM) Fuel Cell Systems Project ID: 85 Principal Investigator: Brian James Keywords: Costs; fuel cells; stationary Performer Principal Investigator: Brian James Organization: Directed Technologies, Inc. (DTI) Address: 3601 Wilson Blvd., Suite 650 Arlington, VA 22201 Telephone: 703-243-3383 Email: brian_james@directedtechnologies.com Period of Performance End: November 1999 Project Description Type of Project: Analysis Category: Cross-Cutting Objectives: Estimate the cost of the fuel cell system using the Directed Technologies, Inc. cost database built up over the several years under U.S. Department of Energy and Ford Motor Company contracts.

344

Opportunity Fuels Guidebook  

Science Conference Proceedings (OSTI)

Power generators are considering cofiring alternative fuels in their coal-fired boilers because such operations may offer opportunities to lower their fuel costs, enhance customer relationships, or meet possible future mandates requiring renewable sources or reduced fossil carbon emissions. In this guidebook, companies can find information drawn from research, testing, and experience with six categories of these opportunity fuels.

1998-10-13T23:59:59.000Z

345

COSTS OF NUCLEAR POWER  

SciTech Connect

The discussion on the costs of nuclear power from stationary plants, designed primarily for the generation of electricity. deals with those plants in operation, being built, or being designed for construction at an early date. An attempt is made to consider the power costs on the basis of consistent definitions and assumptions for the various nuclear plants and for comparable fossil-fuel plants. Information on several new power reactor projects is included. (auth)

1961-01-01T23:59:59.000Z

346

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network (OSTI)

Well-to-wheels analysis of hydrogen based fuel-cell vehicleJP, et al. Distributed Hydrogen Fueling Systems Analysis,”Year 2006 UCD—ITS—RR—06—04 Hydrogen Refueling Station Costs

Weinert, Jonathan X.; Shaojun, Liu; Ogden, Joan M; Jianxin, Ma

2006-01-01T23:59:59.000Z

347

Fuel Cell Technologies Office: Hydrogen Compression, Storage...  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydrogen Compression, Storage, and Dispensing Cost Reduction Workshop to someone by E-mail Share Fuel Cell Technologies Office: Hydrogen Compression, Storage, and Dispensing Cost...

348

The "Task Approach" to Labor Markets: An Overview  

E-Print Network (OSTI)

An emerging literature argues that changes in the allocation of workplace “tasks” between capital and labor, and between domestic and foreign workers, has altered the structure of labor demand in industrialized countries ...

Author, David H.

2013-01-30T23:59:59.000Z

349

The "Task Approach" to Labor Markets" An Overview  

E-Print Network (OSTI)

An emerging literature argues that changes in the allocation of workplace “tasks” between capital and labor, and between domestic and foreign workers, has altered the structure of labor demand in industrialized countries ...

Autor, David

2013-01-24T23:59:59.000Z

350

Office of the Assistant General Counsel for Labor and Pension...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Labor and Pension Law Energy Policy ARPA-E Laws & Legal Resources Open Government SmartGrid Information The Office of the Assistant General Counsel for Labor and Pension Law...

351

14.64 Labor Economics and Public Policy, Spring 2006  

E-Print Network (OSTI)

Theory and evidence concerning the functioning of the labor market. Particular emphasis on the roles played by government and institutions. Topics include minimum wages, labor market effects of social insurance and welfare ...

Angrist, Joshua David

352

Fuels - Biodiesel  

NLE Websites -- All DOE Office Websites (Extended Search)

* Biodiesel * Biodiesel * Butanol * Ethanol * Hydrogen * Natural Gas * Fischer-Tropsch Batteries Cross-Cutting Assessments Engines GREET Hybrid Electric Vehicles Hydrogen & Fuel Cells Materials Modeling, Simulation & Software Plug-In Hybrid Electric Vehicles PSAT Smart Grid Student Competitions Transportation Research and Analysis Computing Center Working With Argonne Contact TTRDC Clean Diesel Fuels Background Reducing our country's dependence on foreign oil and the rising costs of crude oil are primary reasons for a renewed interest in alternative fuels for the transportation sector. Stringent emissions regulations and public concern about mobile sources of air pollution provide additional incentives to develop fuels that generate fewer emissions, potentially reducing the need for sophisticated, expensive exhaust after-treatment devices.

353

Contiguous Platinum Monolayer Oxygen Reduction Electrocatalysts on High-Stability Low-Cost Supports - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

7 7 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Radoslav Adzic (Primary Contact), Miomir Vukmirovic, Kotaro Sasaki, Jia Wang, Yang Shao-Horn 1 , Rachel O'Malley 2 Brookhaven National Laboratory (BNL), Bldg. 555 Upton, NY 11973-5000 Phone: (631) 344-4522 Email: adzic@bnl.gov DOE Manager HQ: Nancy Garland Phone: (202) 586-5673 Email: Nancy.Garland@ee.doe.gov Subcontractors: 1 Massachusetts Institute of Technology (MIT), Cambridge MA 2 Johnson Matthey Fuel Cells (JMFC), London, England Project Start Date: July 1, 2009 Project End Date: September 30, 2013 Fiscal Year (FY) 2012 Objectives Developing high-performance fuel cell electrocatalysts for the oxygen reduction reaction (ORR) comprising contiguous Pt monolayer (ML) on stable, inexpensive metal

354

Explicit and implicit copayments for phototherapy: examining the cost of commuting  

E-Print Network (OSTI)

Table  1.    Patients’  cost  for  office-­?based  2.  Differences  in  cost  based  on  fuel  efficiency  Statistics.    2010  Cost  of  Owning  and  Operating  a  

Yentzer, Brad A; Gustafson, Cheryl J; Feldman, Steven R

2013-01-01T23:59:59.000Z

355

AVCEM: Advanced Vehicle Cost and Energy Use Model. Overview of AVCEM  

E-Print Network (OSTI)

of the battery, according to the battery cost equations (seediscussion of battery cost above). There actually are twoin the amount and cost of fuel-storage, battery, vehicle

Delucchi, Mark

2005-01-01T23:59:59.000Z

356

Labor arbitrage : impact of offshoring in the U.S. labor market  

E-Print Network (OSTI)

The rapid growth of offshoring has ignited a contentious debate over its impact on the US labor market. Between 1983 and 2002, the United States economy lost 6 million jobs in manufacturing and income inequality increased ...

Malibran, Jorge (Malibran Ángel)

2013-01-01T23:59:59.000Z

357

EPA Fuel Economy Ratings  

NLE Websites -- All DOE Office Websites (Extended Search)

Current Window Sticker Current Window Sticker The U.S. Environmental Protection Agency (EPA) and the National Highway Traffic Safety Administration (NHTSA) recently redesigned and enhanced the window sticker that appears on new vehicles. The new Fuel Economy and Environment Label will be mandatory on all new vehicles beginning with the 2013 model year. For the 2012 model year, manufacturers can use the new window sticker or the older window sticker shown below. Roll over the highlighted elements on the label below to learn more about EPA's current fuel economy label. EPA's Current Fuel Economy Label EPA's New Fuel Economy Label Estimated Annual Fuel Cost: $2,039 based on 15,000 mile at $2.80 per gallon Your fuel cost may differ depending on annual miles and fuel prices. Combined Fuel Economy for this Vehicle: 21 MPG, Range for all SUVs: 10-31

358

Heliostat cost reduction study.  

DOE Green Energy (OSTI)

Power towers are capable of producing solar-generated electricity and hydrogen on a large scale. Heliostats are the most important cost element of a solar power tower plant. Since they constitute {approx} 50% of the capital cost of the plant it is important to reduce heliostat cost as much as possible to improve the economic performance of power towers. In this study we evaluate current heliostat technology and estimate a price of $126/m{sup 2} given year-2006 materials and labor costs for a deployment of {approx}600 MW of power towers per year. This 2006 price yields electricity at $0.067/kWh and hydrogen at $3.20/kg. We propose research and development that should ultimately lead to a price as low as $90/m{sup 2}, which equates to $0.056/kWh and $2.75/kg H{sup 2}. Approximately 30 heliostat and manufacturing experts from the United States, Europe, and Australia contributed to the content of this report during two separate workshops conducted at the National Solar Thermal Test Facility.

Jones, Scott A.; Lumia, Ronald. (University of New Mexico, Albuquerque, NM); Davenport, Roger (Science Applications International Corporation, San Diego, CA); Thomas, Robert C. (Advanced Thermal Systems, Centennial, CO); Gorman, David (Advanced Thermal Systems, Larkspur, CO); Kolb, Gregory J.; Donnelly, Matthew W.

2007-06-01T23:59:59.000Z

359

A COMPARISON OF THE NUCLEAR DEFENSE CAPABILITIES ON NUCLEAR AND COAL-FIRED POWER PLANTS. FUEL COST STUDY VARIOUS REACTORS AT 100 AND 300 Mwe  

SciTech Connect

Appendices C and D may further be identified as SL1925 and CF-61-12- 20(Rev.), respectively. A comparative report is presented in which the economics and feasibility of plant protection from nuclear attack by plant hardening, remote siting, and utilization of optional fueling concepts for the coal-fired plant are evaluated. (J.R.D.)

Gift, E.H.

1962-05-29T23:59:59.000Z

360

Advanced Fuel Cycle Economic Sensitivity Analysis  

Science Conference Proceedings (OSTI)

A fuel cycle economic analysis was performed on four fuel cycles to provide a baseline for initial cost comparison using the Gen IV Economic Modeling Work Group G4 ECON spreadsheet model, Decision Programming Language software, the 2006 Advanced Fuel Cycle Cost Basis report, industry cost data, international papers, the nuclear power related cost study from MIT, Harvard, and the University of Chicago. The analysis developed and compared the fuel cycle cost component of the total cost of energy for a wide range of fuel cycles including: once through, thermal with fast recycle, continuous fast recycle, and thermal recycle.

David Shropshire; Kent Williams; J.D. Smith; Brent Boore

2006-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Transportation Energy Futures Series: Alternative Fuel Infrastructure...  

NLE Websites -- All DOE Office Websites (Extended Search)

Production Capacity, and Retail Availability for Low-Carbon Scenarios TRANSPORTATION ENERGY FUTURES SERIES: Alternative Fuel Infrastructure Expansion: Costs, Resources,...

362

NREL: Hydrogen and Fuel Cells Research - Fuel Cell Electric Vehicle...  

NLE Websites -- All DOE Office Websites (Extended Search)

the cost and increasing the performance of fuel cell propulsion systems, and most major vehicle manufacturers are geared to launch fuel cell electric vehicles in the U.S. market...

363

Flexible Fuel Vehicles: Providing a Renewable Fuel Choice  

DOE Green Energy (OSTI)

This Clean Cities Program fact sheet describes aspects of flexible fuel vehicles such as use of E85, special features, benefits of use, costs, and fueling locations. It discusses performance and lists additional resources.

Not Available

2007-05-01T23:59:59.000Z

364

Weighing the Costs and Benefits of Renewables Portfolio Standards: A Comparative Analysis of State-Level Policy Impact Projections  

E-Print Network (OSTI)

An Overview of Alternative Fossil Fuel Price and Carbonof renewable technology cost, fossil fuel price uncertainty,energy, including the fossil fuel hedge value of renewable

Chen, Cliff; Wiser, Ryan; Bolinger, Mark

2007-01-01T23:59:59.000Z

365

Fuel Cell Projects Kickoff Meeting  

NLE Websites -- All DOE Office Websites (Extended Search)

of Cost-Competitive Fuel Cell Stacks James Cross, Nuvera 4:30 Fuel Cell Fundamentals at Low and Subzero Temperatures Adam Weber, LBNL 4:50 Development and Validation of...

366

Economic analysis of fuel recycle  

SciTech Connect

Economic analysis was performed at KAERI with the assistance of US DOE to compare single reactor fuel cycle costs for a once-through option and a thermal recycle option to operate 1 GWe of a PWR plant for its lifetime. A reference fuel cycle cost was first calculated for each option with best estimated reference input data. Then a sensitivity analysis was performed changing each single value of such fuel cycle component costs as yellow cake price, enrichment charges, spent fuel storage cost, reprocessing cost, spent fuel disposal cost and reprocessing waste disposal cost. Savings due to thermal recycle in requirements of uranium, conversion, and enrichment were examined using formulas suggested by US DOE, while MOX fabrication penalty was accounted for. As a result of the reference fuel cycle cost analysis, it is calculated that the thermal recycle option is marginally more economical than the once-through option. The major factors affecting the comparative costs between thermal recycle and once-through are the costs of reprocessing, spent fuel storage and the difference between spent fuel disposal and reprocessing waste disposal. However, considering the uncertainty in these cost parameters there seems no immediate economic incentive for thermal recycle at the present time.

Juhn, P.E.

1985-01-01T23:59:59.000Z

367

Sensitivity Analysis of H2-Vehicles' Market Prospects, Costs and Benefits - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

1 1 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program David L. Greene (Primary Contact), Zhenhong Lin, Jing Dong Oak Ridge National Laboratory National Transportation Research Center 2360 Cherahala Boulevard Knoxville, TN 37932 Phone: (865) 946-1310 Email: dlgreene@ornl.gov DOE Manager HQ: Fred Joseck Phone: (202) 586-7932 Email: Fred.Joseck@hq.doe.gov Subcontractor: Department of Industrial Engineering, University of Tennessee, Knoxville, TN Project Start Date: October, 2010 Project End Date: Project continuation and direction determined annually by DOE Fiscal Year (FY) 2012 Objectives Project market shares of hydrogen fuel cell vehicles * (FCVs) under varying market conditions using the Market Acceptance of Advanced Automotive Technologies (MA3T) model.

368

Development of Advanced Manufacturing Technologies for Low Cost Hydrogen Storage Vessels - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

1 1 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Mark Leavitt Quantum Fuel Systems Technologies Worldwide, Inc. 25242 Arctic Ocean Drive Lake Forest, CA 92630 Phone: (949) 399-4584 Email: mleavitt@qtww.com DOE Managers HQ: Nancy Garland Phone: (202) 586-5673 Email: Nancy.Garland@ee.doe.gov GO: Jesse Adams Phone: (720) 356-1421 Email: Jesse.Adams@go.doe.gov Contract Number: DE-FG36-08GO18055 Subcontractors: * Boeing Research and Technology, Seattle, WA * Pacific Northwest National Laboratory (PNNL), Richland, WA Project Start Date: September 1, 2008 Project End Date: March 31, 2013 Fiscal Year (FY) 2012 Objectives Develop new methods for manufacturing Type IV

369

NREL: Hydrogen and Fuel Cells Research - Fuel Cell Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

with a focus on improving the performance and durability and reducing the cost of fuel cell components and systems. Research efforts involve: Developing advanced catalysts,...

370

United States Trade and Foreign Labor Interests: The Effects on Foreign Labor of Linking Trade with Labor Provisions in Bilateral U.S. Free Trade Agreements  

E-Print Network (OSTI)

standards through our trade agreements…an approach like [EEYOL] would not protect labor rights in Central America in any meaningful way. ”

Soleimani, Jonathan

2008-01-01T23:59:59.000Z

371

Fuel Cells Overview  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydrogen Storage DELIVERY FUEL CELLS STORAGE PRODUCTION TECHNOLOGY VALIDATION CODES & STANDARDS SYSTEMS INTEGRATION / ANALYSES SAFETY EDUCATION RESEARCH & DEVELOPMENT Economy Pat Davis 2 Fuel Cells Technical Goals & Objectives Goal : Develop and demonstrate fuel cell power system technologies for transportation, stationary, and portable applications. 3 Fuel Cells Technical Goals & Objectives Objectives * Develop a 60% efficient, durable, direct hydrogen fuel cell power system for transportation at a cost of $45/kW (including hydrogen storage) by 2010. * Develop a 45% efficient reformer-based fuel cell power system for transportation operating on clean hydrocarbon or alcohol based fuel that meets emissions standards, a start-up time of 30 seconds, and a projected manufactured cost of $45/kW by

372

Indonesia - Labor Market Policies and International Competitiveness  

E-Print Network (OSTI)

This paper-- a product of the Office of the Vice President, Development Economics-- was prepared as a background paper for World Development Report 1995 on labor. Copies of this paper are available free from the Wor}d Bank, 1818 H Street NW, Washington, DC 20433. Please contact the World Development Report Office, room N7-078, telephone 202-4731393, fax 202-676-0652, Internet address mgeller(a.q)worldbank.org (61 pages). September 1995

N. Agrawal

1995-01-01T23:59:59.000Z

373

USING THE FUEL ECONOMY GUIDE  

NLE Websites -- All DOE Office Websites (Extended Search)

allows you to insert your local gasoline prices and typical driving conditions (% city & highway) to achieve the most accurate fuel cost information for your vehicle. Strengthen...

374

World Fossil Fuel Economics - TMS  

Science Conference Proceedings (OSTI)

Jan 1, 1971 ... World Fossil Fuel Economics ... in world energy demand, particularly in the U. S. and Europe; the consumption patterns and cost patterns of oil, ...

375

the source. Climate Policy and Labor Markets  

E-Print Network (OSTI)

JEL No. J23,Q50 An important component of the debate surrounding climate legislation in the United States is its potential impact on labor markets. Theoretically the connection is ambiguous and depends on the sign of cross-elasticity of labor demand with respect to energy prices, which is a priori unknown. This paper provides some new evidence on this question by estimating the relationship between real electricity prices and indicators of labor market activity using data for 1976-2007. A key contribution of this analysis is that it relies on within-state variation in electricity prices to identify the models and considers all sectors of the U.S. economy rather than focusing only on the manufacturing sector. The main finding is that employment rates are weakly related to electricity prices with implied cross elasticity of full-time equivalent (FTE) employment with respect to electricity prices ranging from-0.16 % to-0.10%. I conclude by interpreting these empirical estimates in the context of increases in electricity prices consistent with H.R. 2454, the American Clean Energy and Security Act of 2009. The preferred estimates in this paper suggest that in the short-run, an increase in electricity price of 4 % would lead to a reduction in aggregate FTE

Olivier Deschenes; Olivier Deschenes; Olivier Deschenes

2010-01-01T23:59:59.000Z

376

Diesel fuel filtration system  

SciTech Connect

The American nuclear utility industry is subject to tight regulations on the quality of diesel fuel that is stored at nuclear generating stations. This fuel is required to supply safety-related emergency diesel generators--the backup power systems associated with the safe shutdown of reactors. One important parameter being regulated is the level of particulate contamination in the diesel fuel. Carbon particulate is a natural byproduct of aging diesel fuel. Carbon particulate precipitates from the fuel`s hydrocarbons, then remains suspended or settles to the bottom of fuel oil storage tanks. If the carbon particulate is not removed, unacceptable levels of particulate contamination will eventually occur. The oil must be discarded or filtered. Having an outside contractor come to the plant to filter the diesel fuel can be costly and time consuming. Time is an even more critical factor if a nuclear plant is in a Limiting Condition of Operation (LCO) situation. A most effective way to reduce both cost and risk is for a utility to build and install its own diesel fuel filtration system. The cost savings associated with designing, fabricating and operating the system inhouse can be significant, and the value of reducing the risk of reactor shutdown because of uncertified diesel fuel may be even higher. This article describes such a fuel filtering system.

Schneider, D. [Wisconsin Fuel and Light, Wausau, WI (United States)

1996-03-01T23:59:59.000Z

377

Thin film battery/fuel cell power generation system. Topical report covering Task 5: the design, cost and benefit of an industrial cogeneration system, using a high-temperature solid-oxide-electrolyte (HTSOE) fuel-cell generator  

DOE Green Energy (OSTI)

A literature search and review of the studies analyzing the relationship between thermal and electrical energy demand for various industries and applications resulted in several applications affording reasonable correlation to the thermal and electrical output of the HTSOE fuel cell. One of the best matches was in the aluminum industry, specifically, the Reynolds Aluminum Production Complex near Corpus Christi, Texas. Therefore, a preliminary design of three variations of a cogeneration system for this plant was effected. The designs were not optimized, nor were alternate methods of providing energy compared with the HTSOE cogeneration systems. The designs were developed to the extent necessary to determine technical practicality and economic viability, when compared with alternate conventional fuel (gas and electric) prices in the year 1990.

Not Available

1981-02-25T23:59:59.000Z

378

A model and optimization of alternative fuel vehicle fleet composition with triple bottom line concerns .  

E-Print Network (OSTI)

??Alternative fuel types and technologies are increasingly being advocated for transportation needs to ameliorate concerns around energy security, climate change, and fuel cost. Each fuel… (more)

Zullo, Johnathon

2012-01-01T23:59:59.000Z

379

Synergistically Enhanced Materials and Design Parameters for Reducing the Cost of Hydrogen Storage Tanks - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

5 5 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Kevin L. Simmons (Primary Contact), Kenneth Johnson, and Kyle Alvine Pacific Northwest National Laboratory (PNNL) 902 Battelle Blvd Richland, WA 99352 Phone: (509) 375-3651 Email: Kevin.Simmons@pnnl.gov Norman Newhouse (Lincoln Composites, Inc.), Mike Veenstra (Ford Motor Company), Anand V. Rau (TORAY Carbon Fibers America) and Thomas Steinhausler (AOC, L.L.C.) DOE Managers HQ: Ned Stetson Phone: (202) 586-9995 Email: Ned.Stetson@ee.doe.gov GO: Jesse Adams

380

Development of Low-Cost, High Strength Commercial Textile Precursor (PAN-MA) - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

0 0 DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report C.D. Warren and Felix L. Paulauskas Oak Ridge National Laboratory 1 Bethel Valley Road Oak Ridge, TN 37831 Phone: (865) 574-9693 Email: warrencd@ornl.gov Email: paulauskasfl@ornl.gov DOE Manager HQ: Ned Stetson Phone: (202) 586-9995 Email: Ned.Stetson@ee.doe.gov Contributors: * Hippolyte Grappe (ORNL) * Fue Xiong (ORNL) * Ana Paula Vidigal (FISIPE) * Jose Contrerias (FISIPE) Project Start Date: April 21, 2011 Project End Date: July 31, 2013 Fiscal Year (FY) 2012 Objectives Down-select from 11 polymer candidate polymer *

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

The Actual Cost of Food Systems on  

E-Print Network (OSTI)

emissions and air quality); infrastructure; energy (fuel); congestion; safety; and user (tax payer) costs emissions and air quality); infrastructure; energy (fuel); congestion; safety; and user (tax payer) costs ...................................................................................................................16 Table 14: Fruit and Vegetable Consumption Rate Per Capita from County Survey

Beresnev, Igor

382

Automotive System Cost Modeling Tool (ASCM)  

E-Print Network (OSTI)

technology vehicles (i.e., diesel, hybrid, and fuel cell) developed for improved fuel economy remains either be done through Argonne National laboratory's hybrid vehicle cost model algorithm (adapted the Tool Can Help Answer · What is the life cycle cost of today's midsize hybrid vehicle? · How does

383

Partial Disability System and Labor Market Adjustment: The Case of Spain  

E-Print Network (OSTI)

Although partially disabled individuals in Spain are allowed to combine the receipt of disability benefits with a job, the empirical evidence shows that employment rates for this group of individuals are very low. Therefore, in this paper we construct labor market model with search intensity and matching frictions in order to identify the incentives and disincentives to work provided by the partial disability system in Spain from the point of view of both disabled individuals and employers. According to the model, the high employment rate gap observed between nondisabled and disabled workers can be partially explained by the presence of a lower level of productivity and higher searching costs among disabled individuals that discourage them from looking for jobs. Moreover, the design of the Spanish Disability System also contributes in explaining this gap. We also analyze the role of business cycle conditions in shaping the labor market transitions of disabled individuals.

Jose I. Silva; Judit Vall-castello; Jose I. Silva; Judit Vall-castello

2013-01-01T23:59:59.000Z

384

1998 Fuel Economy Guide  

NLE Websites -- All DOE Office Websites (Extended Search)

purpose vehicles (2-wheel drive and 4-wheel drive). By using this Guide consumers can estimate the average yearly fuel cost for any vehicle. The mileage figures included in...

385

NUCLEAR ENERGY SYSTEM COST MODELING  

Science Conference Proceedings (OSTI)

The U.S. Department of Energy’s Fuel Cycle Technologies (FCT) Program is preparing to perform an evaluation of the full range of possible Nuclear Energy Systems (NES) in 2013. These include all practical combinations of fuels and transmuters (reactors and sub-critical systems) in single and multi-tier combinations of burners and breeders with no, partial, and full recycle. As part of this evaluation, Levelized Cost of Electricity at Equilibrium (LCAE) ranges for each representative system will be calculated. To facilitate the cost analyses, the 2009 Advanced Fuel Cycle Cost Basis Report is being amended to provide up-to-date cost data for each step in the fuel cycle, and a new analysis tool, NE-COST, has been developed. This paper explains the innovative “Island” approach used by NE-COST to streamline and simplify the economic analysis effort and provides examples of LCAE costs generated. The Island approach treats each transmuter (or target burner) and the associated fuel cycle facilities as a separate analysis module, allowing reuse of modules that appear frequently in the NES options list. For example, a number of options to be screened will include a once-through uranium oxide (UOX) fueled light water reactor (LWR). The UOX LWR may be standalone, or may be the first stage in a multi-stage system. Using the Island approach, the UOX LWR only needs to be modeled once and the module can then be reused on subsequent fuel cycles. NE-COST models the unit operations and life cycle costs associated with each step of the fuel cycle on each island. This includes three front-end options for supplying feedstock to fuel fabrication (mining/enrichment, reprocessing of used fuel from another island, and/or reprocessing of this island’s used fuel), along with the transmuter and back-end storage/disposal. Results of each island are combined based on the fractional energy generated by each islands in an equilibrium system. The cost analyses use the probability distributions of key parameters and employs Monte Carlo sampling to arrive at an island’s cost probability density function (PDF). When comparing two NES to determine delta cost, strongly correlated parameters can be cancelled out so that only the differences in the systems contribute to the relative cost PDFs. For example, one comparative analysis presented in the paper is a single stage LWR-UOX system versus a two-stage LWR-UOX to LWR-MOX system. In this case, the first stage of both systems is the same (but with different fractional energy generation), while the second stage of the UOX to MOX system uses the same type transmuter but the fuel type and feedstock sources are different. In this case, the cost difference between systems is driven by only the fuel cycle differences of the MOX stage.

Francesco Ganda; Brent Dixon

2012-09-01T23:59:59.000Z

386

Manufacturing of Low-Cost, Durable Membrane Electrode Assemblies Engineered for Rapid Conditioning - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

1 1 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program F. Colin Busby W.L. Gore & Associates, Inc (Gore) Gore Electrochemical Technologies Team 201 Airport Road Elkton, MD 21921 Phone: (410) 392-3200 Email: CBusby@WLGore.com DOE Managers HQ: Nancy Garland Phone: (202) 586-5673 Email: Nancy.Garland@ee.doe.gov GO: Jesse Adams Phone: (720) 356-1421 Email: Jesse.Adams@go.doe.gov Contract Number: DE-FСЗ6-08G018052 Subcontractors: * UTC Power, South Windsor, CT * University of Delaware, Newark, DE (UD) * University of Tennessee, Knoxville, TN (UTK) Project Start Date: October 1, 2008 Project End Date: June 30, 2014

387

Low-Cost Large-Scale PEM Electrolysis for Renewable Energy Storage - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

6 6 DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report Dr. Katherine Ayers (Primary Contact), Chris Capuano Proton Energy Systems d/b/a Proton OnSite 10 Technology Drive Wallingford, CT 06492 Phone: (203) 678-2190 Email: kayers@protononsite.com DOE Manager HQ: Erika Sutherland Phone: (202) 586-3152 Email: Erika.Sutherland@ee.doe.gov Contract Number: DE-SC0001338 Subcontractors: * 3M, Minneapolis, MN * University of Wyoming, Laramie, WY Project Start Date: June 19, 2010 (Phase 1) Project End Date: August 18, 2013 (with Phase 2 continuation) Fiscal Year (FY) 2012 Project Objectives Demonstrate optimal membrane electrode assembly * (MEA) efficiency through: Refinement of catalyst compositions based on -

388

Cost, Energy Use, and Emissions of Tri-Generation Systems - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

7 7 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Mark F. Ruth* (Primary Contact), Michael E. Goldsby † , Timothy J. Sa † , Victor Diakov* *National Renewable Energy Laboratory 15013 Denver West Pkwy. Golden, CO 80401 Phone: (303) 817-6160 Email: Mark.Ruth@nrel.gov † Sandia National Laboratories DOE Manager HQ: Fred Joseck Phone: (202) 586-7932 Email: Fred.Joseck@ee.doe.gov Project Start Date: December 1, 2010 Project End Date: October 31, 2011 Fiscal Year (FY) 2012 Objectives Develop a macro-system model (MSM): * Aimed at performing rapid cross-cutting analysis - Utilizing and linking other models - Improving consistency between models - Incorporate tri-generation systems into the MSM and * develop a methodology for MSM users to analyze

389

Critical Research for Cost-Effective Photoelectrochemical Production of Hydrogen - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

3 3 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Liwei Xu (Primary Contact) 1 , Anke E. Abken 2 , William B. Ingler 3 , John Turner 4 1 Midwest Optoelectronics LLC (MWOE) 2801 W. Bancroft Street Mail Stop 230 Toledo, OH 43606 Phone: (419) 215-8583 Email: xu@mwoe.com 2 Xunlight Corporation (Xunlight) 3 University of Toledo, Toledo, OH (UT) 4 National Renewable Energy Laboratory, Golden, CO (NREL) DOE Managers HQ: Eric Miller Phone: (202) 287-5829 Email: Eric.Miller@ee.doe.gov GO: David Peterson Phone: (720) 356-1747 Email: David.Peterson@go.doe.gov Contract Number: DE-FG36-05GO15028 Subcontractors: * Xunlight Corporation, Toledo, OH * University of Toledo, Toledo, OH * National Renewable Energy Laboratory, Golden, CO

390

Production Cost Optimization Assessments  

Science Conference Proceedings (OSTI)

The benefits of improved thermal performance of coal-fired power plants continue to grow, as the costs of fuel rise and the prospect of a carbon dioxide cap and trade program looms on the horizon. This report summarizes the efforts to date of utilities committed to reducing their heat rate by 1.0% in the Production Cost Optimization (PCO) Project. The process includes benchmarking of plant thermal performance using existing plant data and a site-specific performance appraisal. The appraisal determines po...

2008-12-11T23:59:59.000Z

391

Low Cost, Durable Seal  

SciTech Connect

Seal durability is critical to achieving the 2010 DOE operational life goals for both stationary and transportation PEM fuel cell stacks. The seal material must be chemically and mechanically stable in an environment consisting of aggressive operating temperatures, humidified gases, and acidic membranes. The seal must also be producible at low cost. Currentlyused seal materials do not meet all these requirements. This project developed and demonstrated a high consistency hydrocarbon rubber seal material that was able to meet the DOE technical and cost targets. Significant emphasis was placed on characterization of the material and full scale molding demonstrations.

Roberts, George; Parsons, Jason; Friedman, Jake

2010-12-17T23:59:59.000Z

392

Environmental protection using social costing  

Science Conference Proceedings (OSTI)

Emissions and other residual wastes come from industrial production, commercial and household activities, and transportation. These wastes damage the environment, including human health. As economies grow, so does concern about balancing that growth with the desire for environmental protection. At issue is how much environmental protection we should have. We address this issue using the concept of social costing. The issue is discussed in the context of electric power generation. There is particular concern about the use of fossil fuels such as petroleum, the major fuel used in the Republic of China, and coal which is the most common fuel used in the U. S. Electric power generation is a major source of airborne pollutants such as SO{sub 2}, NO{sub x} particulate matter, volatile organic compounds, CO, and CO{sub 2}. It also results in liquid and solid wastes, and other effects such as changes in land use. To generate electric power, fuel (such as petroleum, coal or enriched uranium) or some other resource (e.g., wind or geothermal) is needed. A fuel cycle consists of a sequence of activities and processes involved in generating electric power. These activities include fuel extraction, treatment and processing; fuel conversion into electricity; transmission; waste disposal; and transportation of fuel and wastes between the different stages of the fuel cycle. Each stage results in emissions or other residuals. Several recent-studies have been about the environmental costs of electricity.

Lee, R.

1993-10-01T23:59:59.000Z

393

Labor and Safety: Mines and Mining Safety (Indiana)  

Energy.gov (U.S. Department of Energy (DOE))

This section contains labor regulations pertaining specifically to coal mine workers. The law establishes the Indiana Mining Board. The Board's duties include: collecting and distributing...

394

Out of the Ashes: Options for Rebuilding Airline Labor Relations  

E-Print Network (OSTI)

The crisis in the airline industry and its labor relations system creates a window of opportunity to introduce changes that are essential to successful industry recovery. ...

KOCHAN, THOMAS A.

2003-05-02T23:59:59.000Z

395

The Worker Center Movement and Traditional Labor Laws:  

E-Print Network (OSTI)

Industry-focus: Day Labor Construction Grocery & RestaurantRestaurant Employer-targeting? Some targeting of employersCode of Conduct with Restaurant Roundtable members.

Naduris-Weissman, Eli

2007-01-01T23:59:59.000Z

396

Interview: LaborWorks@NeighborWorks Provides Vermont Contractors...  

NLE Websites -- All DOE Office Websites (Extended Search)

Focus Series LaborWorks@NeighborWorks Provides Vermont Contractors With Help When They Need It NeighborWorks of Western Vermont (NWWVT), a nonprofit home ownership organization...

397

The incentive effects of Medicaid on women's labor supply.  

E-Print Network (OSTI)

??Studies have consistently shown that cash benefits provided by the Aid to Families with Dependent Children (AFDC) program alter the labor supply of female heads… (more)

Winkler, Anne Elizabeth

1989-01-01T23:59:59.000Z

398

RECIPIENT:MI Department of Energy, Labor & Economic Growth STATE...  

NLE Websites -- All DOE Office Websites (Extended Search)

MI Department of Energy, Labor & Economic Growth STATE: MI PROJECT TITLE: SEP - Farm Audit Implementation Funding Opportunity Announcement Number Procurement Instrument Number NEPA...

399

Labor Law Enforcement in California, 1970-2000  

E-Print Network (OSTI)

Professional Engineers in California Government. 2001. “WhyProfessional Engineers in California Gov- ernment, November.be over the age of 40. the state of california labor / 2002

Bar-Cohen, Limor; Carrillo, Deana Milam

2002-01-01T23:59:59.000Z

400

Hydrogen & Fuel Cells | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hydrogen & Hydrogen & Fuel Cells Hydrogen & Fuel Cells Meet Brian Larsen, a materials scientist who is helping lower fuel cell costs by developing the next generation of fuel cell catalysts. Meet Brian Larsen, a materials scientist who is helping lower fuel cell costs by developing the next generation of fuel cell catalysts. Fuel cells produce electricity from a number of domestic fuels, including hydrogen and renewables, and can provide power for virtually any application -- from cars and buses to commercial buildings. This technology, which is similar to a battery, has the potential to revolutionize the way we power the nation while reducing carbon pollution and oil consumption.

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Few transportation fuels surpass the energy densities of ...  

U.S. Energy Information Administration (EIA)

Energy density and the cost, weight, and size of onboard energy storage are important characteristics of fuels for transportation. Fuels that require ...

402

Department of Energy Awards Nearly $7 Million to Advance Fuel...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

energy, raw materials, and various components that will help identify ways to drive down production costs of transportation fuel cell systems, stationary fuel cell systems, and...

403

MEMS Fuel Cells – Low Temp – High Power Density  

The miniature fuel-cell technology uses thin-film fuel ... Reduced life cycle cost in comparison to ... for the Department of Energy's National Nuclear Security ...

404

ANALYSIS OF POWER BALANCING WITH FUEL CELLS & HYDROGEN  

E-Print Network (OSTI)

.....................................................................................17 B.2 Costs of fuels, fuel handling, electricity and CO2 quotas.........................................................................................................35 D. ­ TANK-TO-ELECTRICITY AND TANK...........................................................................................................36 D.2 Reference Car

405

An Economic Analysis of Select Fuel Cycles Using the Steady-State Analysis Model for Advanced Fuel Cycles Schemes (SMAFS)  

Science Conference Proceedings (OSTI)

The U.S. Department of Energy's (DOE) Global Nuclear Energy Partnership (GNEP) is currently considering alternatives to the current U.S. once-through fuel cycle. This report evaluates the relative economics of three alternative fuel cycles to determine those cost components important to overall fuel cycle costs and total generation costs. The analysis determined that the unit cost of nuclear reactors is the most important nuclear generation cost parameter in future fuel cycles. The report also evaluates ...

2007-12-20T23:59:59.000Z

406

A Total Cost of Ownership Model for Design and Manufacturing Optimization of Fuel Cells in Stationary and Emerging Market Applications - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

3 3 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Max Wei (Primary Contact), Tom McKone, Tim Lipman 1 , David Dornfeld 2 , Josh Chien 2 , Chris Marnay, Adam Weber, Paul Beattie 3 , Patricia Chong 3 Lawrence Berkeley National Laboratory (LBNL) 1 Cyclotron Road MS 90R-4000 Berkeley, CA 94706 Phone: (510) 486-5220 Email: mwei@lbl.gov DOE Manager HQ: Jason Marcinkoski Phone: (202) 586-7466 Email: Jason.Marcinkoski@ee.doe.gov Subcontractors: 1 University of California, Berkeley, Transportation Sustainability Research Center and DOE Pacific Region Clean Energy Application Center, Berkeley, CA 2 University of California, Berkeley, Laboratory for Manufacturing and Sustainability, Department of Mechanical Engineering, Berkeley, CA

407

Grid-connected integrated community energy system. Phase II, Stage 1, final report. Conceptual design, demand and fuel projections and cost analysis  

DOE Green Energy (OSTI)

The Phase I Report, Grid ICES, presented the broad alternatives and implications for development of an energy system satisfying thermal demand with the co-generation of electric power, all predicated on the use of solid fuels. Participants of the system are the University of Minnesota, operator and primary thermal user, and Northern States Power Company, primary electrical user; with St. Mary's Hospital, Fairview Hospital, and Augsburg College as Add-on Customers for the thermal service (Option I). Included for consideration are the Options of (II) solid waste disposal by the Pyrolysis Method, with heat recovery, and (III) conversion of a portion of the thermal system from steam to hot water distribution to increase co-generation capability and as a demonstration system for future expansion. This report presents the conceptual design of the energy system and each Option, with the economic implications identified so that selection of the final system can be made. Draft outline of the Environmental Assessment for the project is submitted as a separate report.

Not Available

1978-03-08T23:59:59.000Z

408

Labor market trends for health physicists  

Science Conference Proceedings (OSTI)

Information is presented on the recent trends in enrollments, degrees and US civilian, non-medical employment for health physicists. This information is combined with other data such as salary comparisons, indicators of hiring difficulties by the federal government, and information received from employers to assess the current labor market status for health physicists. This information indicates that for the last several years demands for new graduate health physicists have been greater than supplies. An assessment of projected enrollment and degree trends and employment trends through the mid-1990s is presented. This assessment indicates that the current labor market situation is not likely to change -- the number of job openings will continue to exceed the number of new graduates available for employment. Moreover, information is presented which indicates that there are several factors at work in the general economy which will make is difficult to enhance health physics enrollments and degrees. Thus, while the recent increase in enrollments in health physics programs and the addition of two new programs in 1990 is encouraging, these are not enough to meet future employment needs. Employers will, in all likelihood, continue to have difficulties in hiring health physicists, and salaries will continue to be relatively high through the mid-1990s. 16 refs., 8 figs.

Not Available

1991-11-01T23:59:59.000Z

409

DOE Hydrogen Analysis Repository: Cost Analysis of Proton Exchange Membrane  

NLE Websites -- All DOE Office Websites (Extended Search)

Cost Analysis of Proton Exchange Membrane Fuel Cell Systems for Cost Analysis of Proton Exchange Membrane Fuel Cell Systems for Transportation Project Summary Full Title: Cost Analysis of Proton Exchange Membrane (PEM) Fuel Cell Systems for Transportation Project ID: 196 Principal Investigator: Eric Carlson Keywords: Fuel cells, fuel cell vehicles (FCV), transportation, costs Purpose Assess the cost of an 80 kW direct hydrogen fuel cell system relative to the DOE 2005 target of $125/kW. The system includes the fuel cell stack and balance-of-plant (BOP) components for water, thermal, and fuel management, but not hydrogen storage. Performer Principal Investigator: Eric Carlson Organization: TIAX, LLC Address: 15 Acorn Park Cambridge, MA 02140-2328 Telephone: 617-498-5903 Email: carlson.e@tiaxllc.com Additional Performers: P. Kopf, TIAX, LLC; J. Sinha, TIAX, LLC; S. Sriramulu, TIAX, LLC

410

Hydrogen production and delivery analysis in US markets : cost, energy and greenhouse gas emissions.  

DOE Green Energy (OSTI)

Hydrogen production cost conclusions are: (1) Steam Methane Reforming (SMR) is the least-cost production option at current natural gas prices and for initial hydrogen vehicle penetration rates, at high production rates, SMR may not be the least-cost option; (2) Unlike coal and nuclear technologies, the cost of natural gas feedstock is the largest contributor to SMR production cost; (3) Coal- and nuclear-based hydrogen production have significant penalties at small production rates (and benefits at large rates); (4) Nuclear production of hydrogen is likely to have large economies of scale, but because fixed O&M costs are uncertain, the magnitude of these effects may be understated; and (5) Given H2A default assumptions for fuel prices, process efficiencies and labor costs, nuclear-based hydrogen is likely to be more expensive to produce than coal-based hydrogen. Carbon taxes and caps can narrow the gap. Hydrogen delivery cost conclusions are: (1) For smaller urban markets, compressed gas delivery appears most economic, although cost inputs for high-pressure gas trucks are uncertain; (2) For larger urban markets, pipeline delivery is least costly; (3) Distance from hydrogen production plant to city gate may change relative costs (all results shown assume 100 km); (4) Pipeline costs may be reduced with system 'rationalization', primarily reductions in service pipeline mileage; and (5) Liquefier and pipeline capital costs are a hurdle, particularly at small market sizes. Some energy and greenhouse gas Observations: (1) Energy use (per kg of H2) declines slightly with increasing production or delivery rate for most components (unless energy efficiency varies appreciably with scale, e.g., liquefaction); (2) Energy use is a strong function of production technology and delivery mode; (3) GHG emissions reflect the energy efficiency and carbon content of each component in a production-delivery pathway; (4) Coal and natural gas production pathways have high energy consumption and significant GHG emissions (in the absence of carbon caps, taxes or sequestration); (5) Nuclear pathway is most favorable from energy use and GHG emissions perspective; (6) GH2 Truck and Pipeline delivery have much lower energy use and GHG emissions than LH2 Truck delivery; and (7) For LH2 Truck delivery, the liquefier accounts for most of the energy and GHG emissions.

Mintz, M.; Gillette, J.; Elgowainy, A. (Decision and Information Sciences); ( ES)

2009-01-01T23:59:59.000Z

411

How Much Does That Incinerator Cost?  

E-Print Network (OSTI)

Biosecurity on poultry farms includes proper disposal of dead carcasses. In many cases, that means using an incinerator. Calculating the cost of an incinerator means considering long and short-term expenses and the cost of fuel. This publication explains how to select the right size incinerator and calculate all associated costs.

Mukhtar, Saqib; Nash, Catherine; Harman, Wyatte; Padia, Reema

2008-07-25T23:59:59.000Z

412

SOLAR HEATING OF TANK BOTTOMS Application of Solar Heating to Asphaltic and Parrafinic Oils Reducing Fuel Costs and Greenhouse Gases Due to Use of Natural Gas and Propane  

DOE Green Energy (OSTI)

The sale of crude oil requires that the crude meet product specifications for BS&W, temperature, pour point and API gravity. The physical characteristics of the crude such as pour point and viscosity effect the efficient loading, transport, and unloading of the crude oil. In many cases, the crude oil has either a very high paraffin content or asphalt content which will require either hot oiling or the addition of diluents to the crude oil to reduce the viscosity and the pour point of the oil allowing the crude oil to be readily loaded on to the transport. Marginal wells are significantly impacted by the cost of preheating the oil to an appropriate temperature to allow for ease of transport. Highly paraffinic and asphaltic oils exist throughout the D-J basin and generally require pretreatment during cold months prior to sales. The current study addresses the use of solar energy to heat tank bottoms and improves the overall efficiency and operational reliability of stripper wells.

Eugene A. Fritzler

2005-09-01T23:59:59.000Z

413

Electricity Costs  

NLE Websites -- All DOE Office Websites (Extended Search)

Carbon Emissions Caps and the Impact of a Radical Change in Nuclear Electricity Costs journal International Journal of Energy Economics and Policy volume year month chapter...

414

Response to P-887 Adoption of a Fuel Adjustment Mechanism (FAM) for Nova Scotia Power Incorporated  

E-Print Network (OSTI)

, all are intended to ensure that the cost of the fuel used to generate electricity is reflected associated the electricity reflect the cost of fuel used to generate electricity for each consumer. Two periods. Since fuel costs drive the price of electricity, incorrectly estimated fuel costs can impact both

Hughes, Larry

415

Economy-like reward distribution for division of labor  

Science Conference Proceedings (OSTI)

In learning agent team, giving appropriate amount of reward to each agent is necessary for division of labor. In this paper we present a novel approach for a reward allocation in which reward payments are conducted between agents. We consider foraging ... Keywords: autonomous agents, cooperative artificial intelligence systems, division of labor, reinforcement learning

Munetaka Saitoh; Yoshihito Oyama

2006-02-01T23:59:59.000Z

416

NETL: Fuel Cells  

NLE Websites -- All DOE Office Websites (Extended Search)

Fuel Cells Fuel Cells Coal and Power Systems Fuel Cells SECA Logo Welcome to NETL's Fuel Cells Webpage. In partnership with private industry, educational institutions and national laboratories, we are leading the research, development, and demonstration of high efficiency, fuel flexible solid oxide fuel cells (SOFCs) and coal-based SOFC power generation systems for stationary market large central power plants under the Solid State Energy Conversion Alliance (SECA). The SECA cost reduction goal is to have SOFC systems capable of being manufactured at $400 per kilowatt by 2010. Concurrently, the scale-up, aggregation, and integration of the technology will progress in parallel leading to prototype validation of megawatt (MW)-class fuel flexible products by 2012 and 2015. The SECA coal-based systems goal is the development of large

417

Fuel cell market applications  

DOE Green Energy (OSTI)

This is a review of the US (and international) fuel cell development for the stationary power generation market. Besides DOE, GRI, and EPRI sponsorship, the US fuel cell program has over 40% cost-sharing from the private sector. Support is provided by user groups with over 75 utility and other end-user members. Objectives are to develop and demonstrate cost-effective fuel cell power generation which can initially be commercialized into various market applications using natural gas fuel by the year 2000. Types of fuel cells being developed include PAFC (phosphoric acid), MCFC (molten carbonate), and SOFC (solid oxide); status of each is reported. Potential international applications are reviewed also. Fuel cells are viewed as a force in dispersed power generation, distributed power, cogeneration, and deregulated industry. Specific fuel cell attributes are discussed: Fuel cells promise to be one of the most reliable power sources; they are now being used in critical uninterruptible power systems. They need hydrogen which can be generated internally from natural gas, coal gas, methanol landfill gas, or other fuels containing hydrocarbons. Finally, fuel cell development and market applications in Japan are reviewed briefly.

Williams, M.C.

1995-12-31T23:59:59.000Z

418

Ion-driver fast ignition: Reducing heavy-ion fusion driver energy and cost, simplifying chamber design, target fab, tritium fueling and power conversion  

DOE Green Energy (OSTI)

Ion fast ignition, like laser fast ignition, can potentially reduce driver energy for high target gain by an order of magnitude, while reducing fuel capsule implosion velocity, convergence ratio, and required precisions in target fabrication and illumination symmetry, all of which should further improve and simplify IFE power plants. From fast-ignition target requirements, we determine requirements for ion beam acceleration, pulse-compression, and final focus for advanced accelerators that must be developed for much shorter pulses and higher voltage gradients than today's accelerators, to deliver the petawatt peak powers and small focal spots ({approx}100 {micro}m) required. Although such peak powers and small focal spots are available today with lasers, development of such advanced accelerators is motivated by the greater likely efficiency of deep ion penetration and deposition into pre-compressed 1000x liquid density DT cores. Ion ignitor beam parameters for acceleration, pulse compression, and final focus are estimated for two examples based on a Dielectric Wall Accelerator; (1) a small target with {rho}r {approx} 2 g/cm{sup 2} for a small demo/pilot plant producing {approx}40 MJ of fusion yield per target, and (2) a large target with {rho}r {approx} 10 g/cm{sup 2} producing {approx}1 GJ yield for multi-unit electricity/hydrogen plants, allowing internal T-breeding with low T/D ratios, >75 % of the total fusion yield captured for plasma direct conversion, and simple liquid-protected chambers with gravity clearing. Key enabling development needs for ion fast ignition are found to be (1) ''Close-coupled'' target designs for single-ended illumination of both compressor and ignitor beams; (2) Development of high gradient (>25 MV/m) linacs with high charge-state (q {approx} 26) ion sources for short ({approx}5 ns) accelerator output pulses; (3) Small mm-scale laser-driven plasma lens of {approx}10 MG fields to provide steep focusing angles close-in to the target (built-in as part of each target); (4) beam space charge-neutralization during both drift compression and final focus to target. Except for (1) and (2), these critical issues may be explored on existing heavy-ion storage ring accelerator facilities.

Logan, G.; Callahan-Miller, D.; Perkins, J.; Caporaso, G.; Tabak, M.; Moir, R.; Meier, W.; Bangerter, Roger; Lee, Ed

1998-04-01T23:59:59.000Z

419

DOE/Labor Leadership Roundtable Meetings | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE/Labor Leadership Roundtable Meetings DOE/Labor Leadership Roundtable Meetings DOE/Labor Leadership Roundtable Meetings The Roundtable Forum was established to foster a healthy exchange of ideas relative to the Department and the leadership of our Federal and contractor workforce related to safety, communications, and operations. The Department will continue to engage these elements in efforts to improve performance through enhanced labor management relations and encouraging opportunities for collaboration and partnerships. Meeting Documents Available for Download May 17, 2012 DOE/Labor Leadership Roundtable Meeting Meeting agenda Meeting Date: May 17, 2012 January 25, 2011 DOE Roundtable Meeting with Union Leaders Meeting agenda and summary Meeting Date: January 25, 2011 March 16, 2010 Deputy Secretary Roundtable Meeting with Unions

420

Molten Carbonate and Phosphoric Acid Stationary Fuel Cells: Overview and Gap Analysis  

Fuel Cell Technologies Publication and Product Library (EERE)

This report details technical and cost gap analyses of molten carbonate fuel cell and phosphoric acid fuel cell stationary fuel cell power plants and identifies pathways for reducing costs.

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Molten Carbonate and Phosphoric Acid Stationary Fuel Cells: Overview and Gap Analysis  

DOE Green Energy (OSTI)

This report describes the technical and cost gap analysis performed to identify pathways for reducing the costs of molten carbonate fuel cell (MCFC) and phosphoric acid fuel cell (PAFC) stationary fuel cell power plants.

Remick, R.; Wheeler, D.

2010-09-01T23:59:59.000Z

422

Flexible Fuel Vehicles: Providing a Renewable Fuel Choice (Fact Sheet)  

Science Conference Proceedings (OSTI)

Flexible Fuel vehicles are able to operate using more than one type of fuel. FFVs can be fueled with unleaded gasoline, E85, or any combination of the two. Today more than 7 million vehicles on U.S. highways are flexible fuel vehicles. The fact sheet discusses how E85 affects vehicle performance, the costs and benefits of using E85, and how to find E85 station locations.

Not Available

2010-03-01T23:59:59.000Z

423

Alternative Fuels Data Center: Tools  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Tools to someone by Tools to someone by E-mail Share Alternative Fuels Data Center: Tools on Facebook Tweet about Alternative Fuels Data Center: Tools on Twitter Bookmark Alternative Fuels Data Center: Tools on Google Bookmark Alternative Fuels Data Center: Tools on Delicious Rank Alternative Fuels Data Center: Tools on Digg Find More places to share Alternative Fuels Data Center: Tools on AddThis.com... Tools The Alternative Fuels Data Center offers a large collection of helpful tools. These calculators, interactive maps, and data searches can assist fleets, fuel providers, and other transportation decision makers in their efforts to reduce petroleum use. Calculators Vehicle Cost Calculator Compare cost of ownership and emissions for most vehicle models. Icon_mobile_version mobile

424

How Responsive is Higher Education? The Linkages between Higher Education and the Labor Market  

E-Print Network (OSTI)

in Economics to the Labor Market” Journal of EconomicUnemployment and Labor Market Rigidities: Europe versusEducation and the Labour Market: A Broader Perspective. ”

Bardhan, Ashok Deo; Hicks, Daniel; Jaffee, Dwight M.

2010-01-01T23:59:59.000Z

425

Model Year 1999 Fuel Economy Guide  

NLE Websites -- All DOE Office Websites (Extended Search)

FUEL FUEL ECONOMY GUIDE MODEL YEAR 1999 DOE/EE-0178 Fuel Economy Estimates October 1998 1 CONTENTS PAGE Purpose of the Guide ..................................................... 1 Interior Volume ................................................................ 1 How the Fuel Economy Estimates are Obtained ........... 1 Factors Affecting MPG .................................................... 2 Fuel Economy and Climate Change ............................... 2 Gas Guzzler Tax ............................................................. 2 Vehicle Classes Used in This Guide. .............................. 2 Annuel Fuel Costs .......................................................... 3 How to Use the Guide .................................................... 4 Where to Re-order Guides

426

Realistic costs of carbon capture  

Science Conference Proceedings (OSTI)

There is a growing interest in carbon capture and storage (CCS) as a means of reducing carbon dioxide (CO2) emissions. However there are substantial uncertainties about the costs of CCS. Costs for pre-combustion capture with compression (i.e. excluding costs of transport and storage and any revenue from EOR associated with storage) are examined in this discussion paper for First-of-a-Kind (FOAK) plant and for more mature technologies, or Nth-of-a-Kind plant (NOAK). For FOAK plant using solid fuels the levelised cost of electricity on a 2008 basis is approximately 10 cents/kWh higher with capture than for conventional plants (with a range of 8-12 cents/kWh). Costs of abatement are found typically to be approximately US$150/tCO2 avoided (with a range of US$120-180/tCO2 avoided). For NOAK plants the additional cost of electricity with capture is approximately 2-5 cents/kWh, with costs of the range of US$35-70/tCO2 avoided. Costs of abatement with carbon capture for other fuels and technologies are also estimated for NOAK plants. The costs of abatement are calculated with reference to conventional SCPC plant for both emissions and costs of electricity. Estimates for both FOAK and NOAK are mainly based on cost data from 2008, which was at the end of a period of sustained escalation in the costs of power generation plant and other large capital projects. There are now indications of costs falling from these levels. This may reduce the costs of abatement and costs presented here may be 'peak of the market' estimates. If general cost levels return, for example, to those prevailing in 2005 to 2006 (by which time significant cost escalation had already occurred from previous levels), then costs of capture and compression for FOAK plants are expected to be US$110/tCO2 avoided (with a range of US$90-135/tCO2 avoided). For NOAK plants costs are expected to be US$25-50/tCO2. Based on these considerations a likely representative range of costs of abatement from CCS excluding transport and storage costs appears to be US$100-150/tCO2 for first-of-a-kind plants and perhaps US$30-50/tCO2 for nth-of-a-kind plants.The estimates for FOAK and NOAK costs appear to be broadly consistent in the light of estimates of the potential for cost reductions with increased experience. Cost reductions are expected from increasing scale, learning on individual components, and technological innovation including improved plant integration. Innovation and integration can both lower costs and increase net output with a given cost base. These factors are expected to reduce abatement costs by approximately 65% by 2030. The range of estimated costs for NOAK plants is within the range of plausible future carbon prices, implying that mature technology would be competitive with conventional fossil fuel plants at prevailing carbon prices.

Al Juaied, Mohammed (Harvard Univ., Cambridge, MA (US). Belfer Center for Science and International Affiaris); Whitmore, Adam (Hydrogen Energy International Ltd., Weybridge (GB))

2009-07-01T23:59:59.000Z

427

Assessment of Coal Handling for Fuel Flexibility  

Science Conference Proceedings (OSTI)

To reduce total generating costs, power generators may use multiple solid fuels. This study is a preliminary investigation of the methods and costs of handling multiple solid fuels. An important byproduct of the study was some of the first-ever systematic comparisons of coal handling costs at a sample of plants.

1998-09-03T23:59:59.000Z

428

Print the Fuel Economy Guide  

NLE Websites -- All DOE Office Websites (Extended Search)

Print the Fuel Economy Guide Print the Fuel Economy Guide 2014 Fuel Economy Guide 2014 Fuel Economy Guide Adobe Acrobat Icon MPG data updated December 19, 2013 The annual fuel cost estimates in the 2008-2014 electronic fuel economy guides are updated weekly to match EIA's current national average prices for gasoline and diesel fuel. Order a printed copy: Order Note that the published guides may not be as up-to-date at the downloadable version. View vehicles from 1984 to the present: Go to Find-a-Car Unlike the annual guides which cover only one model year, Find-a-Car provides the most up-to-date fuel economy information for vehicles from model year 1984 to the present, along with environmental and safety data. Find a Car Developer Tools 2013 Fuel Economy Guide 2013 Fuel Economy Guide Adobe Acrobat Icon

429

Fuel Cell Technologies Office: Financial Incentives for Hydrogen...  

NLE Websites -- All DOE Office Websites (Extended Search)

to help minimize the cost of hydrogen and fuel cell projects. It offers an investment tax credit of 30% for qualified fuel cell property or 3,000kW of the fuel cell...

430

PHENIX Work Breakdown Structure. Cost and schedule review copy  

Science Conference Proceedings (OSTI)

The Work Breakdown Structure (WBS) Book begins with this Overview section, which contains the high-level summary cost estimate, the cost profile, and the global construction schedule. The summary cost estimate shows the total US cost and the cost in terms of PHENIX construction funds for building the PHENIX detector. All costs in the WBS book are shown in FY 1993 dollars. Also shown are the institutional and foreign contributions, the level of pre-operations funding, and the cost of deferred items. Pie charts are presented at PHENIX WBS level 1 and 2 that show this information. The PHENIX construction funds are shown broken down to PHENIX WBS level 3 items per fiscal year, and the resulting profile is compared to the RHIC target profile. An accumulated difference of the two profiles is also shown. The PHENIX global construction schedule is presented at the end of the Overview section. Following the Overview are sections for each subsystem. Each subsystem section begins with a summary cost estimate, cost profile, and critical path. The total level 3 cost is broken down into fixed costs (M&S), engineering costs (EDIA) and labor costs. Costs are further broken down in terms of PHENIX construction funds, institutional and foreign contributions, pre-operations funding, and deferred items. Also shown is the contingency at level 3 and the level 4 breakdown of the total cost. The cost profile in fiscal years is shown at level 3. The subsystem summaries are followed by the full cost estimate and schedule sheets for that subsystem. These detailed sheets are typically carried down to level 7 or 8. The cost estimate shows Total, M&S, EDIA, and Labor breakdowns, as well as contingency, for each WBS entry.

Not Available

1994-02-01T23:59:59.000Z

431

PHENIX WBS notes. Cost and schedule review copy  

Science Conference Proceedings (OSTI)

The Work Breakdown Structure (WBS) Book begins with this Overview section, which contains the high-level summary cost estimate, the cost profile, and the global construction schedule. The summary cost estimate shows the total US cost and the cost in terms of PHENIX construction funds for building the PHENIX detector. All costs in the WBS book are shown in FY 1993 dollars. Also shown are the institutional and foreign contributions, the level of pre-operations funding, and the cost of deferred items. Pie charts are presented at PHENIX WBS level 1 and 2 that show this information. The PHENIX construction funds are shown broken down to PHENIX WBS level 3 items per fiscal year, and the resulting profile is compared to the RHIC target profile. An accumulated difference of the two profiles is also shown. The PHENIX global construction schedule is presented at the end of the Overview section. Following the Overview are sections for each subsystem. Each subsystem section begins with a summary cost estimate, cost profile, and critical path. The total level 3 cost is broken down into fixed costs (M&S), engineering costs (EDIA) and labor costs. Costs are further broken down in terms of PHENIX construction funds, institutional and foreign contributions, pre-operations funding, and deferred items. Also shown is the contingency at level 3 and the level 4 breakdown of the total cost. The cost profile in fiscal years is shown at level 3. The subsystem summaries are followed by the full cost estimate and schedule sheets for that subsystem. These detailed sheets are typically carried down to level 7 or 8. The cost estimate Total, M&S, EDIA, and Labor breakdowns, as well as contingency, for each WBS entry.

Not Available

1994-02-01T23:59:59.000Z

432

MRS/IS facility co-located with a repository: preconceptual design and life-cycle cost estimates  

SciTech Connect

A program is described to examine the various alternatives for monitored retrievable storage (MRS) and interim storage (IS) of spent nuclear fuel, solidified high-level waste (HLW), and transuranic (TRU) waste until appropriate geologic repository/repositories are available. The objectives of this study are: (1) to develop a preconceptual design for an MRS/IS facility that would become the principal surface facility for a deep geologic repository when the repository is opened, (2) to examine various issues such as transportation of wastes, licensing of the facility, and environmental concerns associated with operation of such a facility, and (3) to estimate the life cycle costs of the facility when operated in response to a set of scenarios which define the quantities and types of waste requiring storage in specific time periods, which generally span the years from 1990 until 2016. The life cycle costs estimated in this study include: the capital expenditures for structures, casks and/or drywells, storage areas and pads, and transfer equipment; the cost of staff labor, supplies, and services; and the incremental cost of transporting the waste materials from the site of origin to the MRS/IS facility. Three scenarios are examined to develop estimates of life cycle costs of the MRS/IS facility. In the first scenario, HLW canisters are stored, starting in 1990, until the co-located repository is opened in the year 1998. Additional reprocessing plants and repositories are placed in service at various intervals. In the second scenario, spent fuel is stored, starting in 1990, because the reprocessing plants are delayed in starting operations by 10 years, but no HLW is stored because the repositories open on schedule. In the third scenario, HLW is stored, starting in 1990, because the repositories are delayed 10 years, but the reprocessing plants open on schedule.

Smith, R.I.; Nesbitt, J.F.

1982-11-01T23:59:59.000Z

433

TAX AND FEE PAYMENTS BY MOTOR VEHICLE USERS FOR THE USE OF HIGHWAYS, FUELS, AND VEHICLES Report #17 in the series: The Annualized Social Cost of Motor-Vehicle Use in the United States, based on 1990-1991 Data  

E-Print Network (OSTI)

the Full Social Costs and Benefits of Transportation, ed. bythe Full Social Costs and Benefits of Transportation, ed. bytransportation infrastructure and services, then we should set prices on the infrastructure and services equal to marginal social costs.

Delucchi, Mark

2005-01-01T23:59:59.000Z

434

Gasoline and Diesel Fuel Update  

Gasoline and Diesel Fuel Update (EIA)

Methodology For Gasoline and Diesel Fuel Pump Components Methodology For Gasoline and Diesel Fuel Pump Components The components for the gasoline and diesel fuel pumps are calculated in the following manner in cents per gallon and then converted into a percentage: Crude Oil - the monthly average of the composite refiner acquisition cost, which is the average price of crude oil purchased by refiners. Refining Costs & Profits - the difference between the monthly average of the spot price of gasoline or diesel fuel (used as a proxy for the value of gasoline or diesel fuel as it exits the refinery) and the average price of crude oil purchased by refiners (the crude oil component). Distribution & Marketing Costs & Profits - the difference between the average retail price of gasoline or diesel fuel as computed from EIA's

435

Types of Costs Types of Cost Estimates  

E-Print Network (OSTI)

· Types of Costs · Types of Cost Estimates · Methods to estimate capital costs MIN E 408: Mining the equipment for reclamation? Types of Costs #12;· Marginal Cost: ­ Change in total cost ­ Any production process involves fixed and variable costs. As production increases/expands, fixed costs are unchanged, so

Boisvert, Jeff

436

Distributed Energy Fuel Cells  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Fuel Cells Energy Fuel Cells DOE Hydrogen DOE Hydrogen and and Fuel Cells Fuel Cells Coordination Meeting Fuel Cell Coordination Meeting June 2-3, 2003 Electricity Users Kathi Epping Kathi Epping Objectives & Barriers Distributed Energy OBJECTIVES * Develop a distributed generation PEM fuel cell system operating on natural gas or propane that achieves 40% electrical efficiency and 40,000 hours durability at $400-750/kW by 2010. BARRIERS * Durability * Heat Utilization * Power Electronics * Start-Up Time Targets and Status Integrated Stationary PEMFC Power Systems Operating on Natural Gas or Propane Containing 6 ppm Sulfur 40,000 30,000 15,000 Hours Durability 750 1,250 2,500 $/kWe Cost 40 32 30 % Electrical Efficiency Large (50-250 kW) Systems 40,000 30,000 >6,000 Hours Durability 1,000 1,500 3,000

437

Alternative Fuels Data Center  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Idaho Incentives and Laws Idaho Incentives and Laws The following is a list of expired, repealed, and archived incentives, laws, regulations, funding opportunities, or other initiatives related to alternative fuels and vehicles, advanced technologies, or air quality. Biofuel Fueling Infrastructure Tax Credit Expired: 12/31/2011 An income tax credit is available for qualified biofuel fueling infrastructure. The credit is 6% of the cost to install new, or upgrade existing, fueling infrastructure for the purpose of selling and dispensing biofuel. The allowable credit cannot exceed 50% of the taxpayer's income tax liability. For the purpose of this incentive, biofuel is defined as any fuel offered for sale as a transportation fuel that is agriculturally derived and meets applicable ASTM standards, including, but not limited to,

438

Alternative Fuels Data Center  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Oklahoma Incentives and Laws Oklahoma Incentives and Laws The following is a list of expired, repealed, and archived incentives, laws, regulations, funding opportunities, or other initiatives related to alternative fuels and vehicles, advanced technologies, or air quality. Alternative Fuel Vehicle (AFV) and Fueling Infrastructure Loans Archived: 08/01/2013 The Oklahoma Department of Central Services' Alternative Fuels Conversion Loan program provides 0% interest loans to government fleets for converting vehicles to operate on alternative fuels, the construction of AFV fueling infrastructure, and the incremental cost associated with the purchase of an original equipment manufacturer AFV. The program provides up to $10,000 per converted or newly purchased AFV and up to $300,000 for the development or

439

Socioeconomic impact assessment: a methodology applied to synthetic fuels  

DOE Green Energy (OSTI)

This Report is a supporting document for the Final Environmental Impact Statement, Alternative Fuels Demonstration Program, which was filed with the Council on Environmental Quality in November, 1977. It describes the methodology developed for the socioeconomic impact assessments contained in the Environmental Impact Statement, and highlights the findings. Part I of this Report explains clearly how the numbers are derived, and presents the salient planning issues. Starting with the labor force of a synthetic fuels facility, a public official, decision-maker, or student of socioeconomic impacts can use this Report to derive a reasonable set of estimates which reflect the resultant population, income, employment, land use, public facility costs, and local public revenues. Part II of this Report is the application of this methodology to synthetic fuels. Numerical estimates are given for the social and economic effects resulting from such energy technologies as coal gasification and liquefaction, oil shale, and the conversion of solid wastes and agricultural products to energy. Although the methodology is not site specific, illustrative sites, chosen from the major coal-bearing counties in the United States, have been included. This allows a user to compare the relative impacts of a given energy facility in various geographical locations and types of communities. The section on mitigating measures may be of special interest because of its treatment of problem areas and its broad range of suggested solutions. One advantage of the methodology is that it derives from a broad data base that is readily accessible: the United States Census. Another advantage is that impacts can be calculated by hand. Finally, it is applicable to a wide variety of energy technologies and not restricted to synthetic fuels.

Not Available

1978-04-01T23:59:59.000Z

440

Low Temperature PEM Fuel Cell Manufacturing Needs  

NLE Websites -- All DOE Office Websites (Extended Search)

PEM Fuel Cell PEM Fuel Cell Manufacturing Needs Presented by Duarte Sousa, PE Manufacturing Fuel Cell Manhattan Project  Cost drivers were identified for the following: * MEA * Plates * Balance of Plant (BOP) * Fuel Processing Manufacturing Fuel Cell Project - Phase 1 Note that this presentation will be MEA centric as this is the working group I represent...  MEA Cost Drivers Identified: Identifying MEA Cost Drivers * The MEA was readily identified as the major cost driver in a 10 kW stationary stack. * The precious metal catalyst electrode is the major cost driver for the MEA. Thus, focus cost reduction efforts on MEA manufacturing methods. Identify gaps in MEA manufacturing technology: How much better can we do? Note: Cost reductions realized from both material price reduction

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Capital costs have major impact on projected power sector ...  

U.S. Energy Information Administration (EIA)

Natural gas-fired power plants dominate the 2011 Annual ... AEO2011 also includes several alternative cases with lower assumed capital costs of nuclear, fossil fuel ...

442

DOE Hydrogen Analysis Repository: Cost Optimization of Proton...  

NLE Websites -- All DOE Office Websites (Extended Search)

density for future scenarios of proton exchange membrane fuel cell (PEMFC) technology; estimate manufacturing cost of PEMFCs. Performer Principal Investigator: Suresh Sriramulu...

443

Energy Department Announces New Investment to Advance Cost ...  

Energy Department Announces New Investment to Advance Cost-Competitive Hydrogen Fuel. February 14, 2013. The Energy Department today announced a $1 million investment ...

444

Electricity Without CO2 Emissions: Assessing the Costs of Carbon...  

NLE Websites -- All DOE Office Websites (Extended Search)

Johnson and Keith: Electricity without CO 2 ... 1 ELECTRICITY FROM FOSSIL FUELS WITHOUT CO 2 EMISSIONS: ASSESSING THE COSTS OF CARBON DIOXIDE CAPTURE AND SEQUESTRATION IN US...

445

TAX AND FEE PAYMENTS BY MOTOR VEHICLE USERS FOR THE USE OF HIGHWAYS, FUELS, AND VEHICLES Report #17 in the series: The Annualized Social Cost of Motor-Vehicle Use in the United States, based on 1990-1991 Data  

E-Print Network (OSTI)

general sales taxes) on motor gasoline (EIA, State Energythe sales tax paid on motor-vehicles, gasoline and motor-Motor fuels: portions of federal gasoline and diesel-fuel tax

Delucchi, Mark

2005-01-01T23:59:59.000Z

446

Active Labor Unions and Organizations Interfacing With DOE | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Services » Outreach & Collaboration » Focus Groups » Active Services » Outreach & Collaboration » Focus Groups » Active Labor Unions and Organizations Interfacing With DOE Active Labor Unions and Organizations Interfacing With DOE This information book is intended to provide an overview of what HSS has learned through our interface with representative labor unions and stakeholders since the inception of the Focus Group, along with accomplishments and current efforts to address identified areas of weakness. Handbook of Active Labor Unions and Organizations Interfacing With DOE More Documents & Publications HSS/Union Leadership Meeting on DOE Safety and Security Reform HSS Work Group Telecom (Draft Charters) Deputy Secretary Roundtable Meeting with Unions Enforcement Guidance Oversight Reporting Security Classification

447

Automated Fetal Heart Rate Analysis in Labor: Decelerations and Overshoots  

Science Conference Proceedings (OSTI)

Electronic fetal heart rate (FHR) recording is a standard way of monitoring fetal health in labor. Decelerations and accelerations usually indicate fetal distress and normality respectively. But one type of acceleration may differ

A. E. Georgieva; S. J. Payne; M. Moulden; C. W. G. Redman

2010-01-01T23:59:59.000Z

448

Housing tenure and labor market impacts: The search goes on  

E-Print Network (OSTI)

We develop two search-theoretic models emphasizing firm entry to examine the Oswald hypothesis, the idea that homeownership is linked to inferior labor market outcomes, and compare their predictions to three extant theories. ...

Coulson, N. Edward

449

Alternative Fuels Data Center: Natural Gas Support  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

the fuel tax to fund necessary transportation infrastructure projects while still resulting in significant cost savings for customers. (Reference House Concurrent Resolution 115...

450

Iowa seeks to end electric fuel surcharge  

SciTech Connect

Iowa is abolishing the fuel cost adjustment credits for investor-owned electric utilities because of illegal utility charges that added non-fuel costs into the credit. Abolishing the energy adjustment credit (EAC) will force utilities to file a rate case in order to pass changes in fuel costs to their customers. Investor-owned and municipal utilities have filed opposing testimony for the September hearing. Opponents claim that there will have to be changes made in the way costs are recovered from cogenerated power purchases and that it will be more difficult to make annual fuel procurements.

Ponczak, G.

1985-09-02T23:59:59.000Z

451

Integrated Used Nuclear Fuel Storage, Transportation, and ...  

Researchers at ORNL have developed an integrated system that reduces the total life-cycle cost of used fuel storage while improving overall safety. This multicanister ...

452

Low-Level Ethanol Fuel Blends  

DOE Green Energy (OSTI)

This fact sheet addresses: (a) why Clean Cities promotes ethanol blends; (b) how these blends affect emissions; (c) fuel performance and availability; and (d) cost, incentives, and regulations.

Not Available

2005-04-01T23:59:59.000Z

453

Adiabatic Fuel Cell Stack - Energy Innovation Portal  

Adiabatic fuel cell stacks are simple, low-cost and reliable. Operating at near-ambient pressure, their efficiency and net power density make them competitive with ...

454

1998 Cost and Quality Annual  

Gasoline and Diesel Fuel Update (EIA)

8) 8) Distribution Category UC-950 Cost and Quality of Fuels for Electric Utility Plants 1998 Tables June 1999 Energy Information Administration Office of Coal, Nuclear, Electric and Alternate Fuels U.S. Department of Energy Washington DC 20585 This report was prepared by the Energy Information Administration, the independent statistical and analytical agency within the Department of Energy. The information contained herein should not be construed as advocating or reflecting any policy position of the Department of Energy or any other organization. Contacts The annual publication Cost and Quality of Fuels for Electric Utility Plants (C&Q) is no longer published by the EIA. The tables presented in this document are intended to replace that annual publication. Questions regarding the availability of these data should

455

Labor Market Trends for Nuclear Engineers Through 2005, 1999 Update Report  

SciTech Connect

This report summarizes the labor market trends for nuclear engineers predicted through the year 2005.

Larry Blair

1999-10-28T23:59:59.000Z

456

May 17, 2012, DOE/Labor Leadership Roundtable Meeting - Agenda  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Labor-Management Roundtable Labor-Management Roundtable Forrestal Building, Washington, DC May 17, 2012 2:00 - 3:00 PM (EST) AGENDA Welcome/Opening Remarks Dr. Steven Chu, Secretary of Energy Introductory Remarks Daniel Poneman, Deputy Secretary of Energy Progress on Union Issues David Sandalow, Acting Under Secretary of Energy Michael Kane, Chief Human Capital Officer David Huizenga, Senior Advisor for Environmental Management Dr. William Brinkman, Director for the Office of Science

457

Labor and energy impacts of energy-conservation measures  

SciTech Connect

Three papers are presented discussing the labor and energy impacts of energy-conservation measures, namely: Generation of the Industry/Occupation Wage Matrix and Related Matters, by Carole Green; Job Shifts from Energy Conservation (Salary Distribution Effects), by Robert A. Herendeen; and Energy and Labor Implication of Improving Thermal Integrity of New Houses, by John Joseph Nangle. A separate abstract was prepared for each paper.

1980-01-01T23:59:59.000Z

458

Fossil fuels -- future fuels  

Science Conference Proceedings (OSTI)

Fossil fuels -- coal, oil, and natural gas -- built America`s historic economic strength. Today, coal supplies more than 55% of the electricity, oil more than 97% of the transportation needs, and natural gas 24% of the primary energy used in the US. Even taking into account increased use of renewable fuels and vastly improved powerplant efficiencies, 90% of national energy needs will still be met by fossil fuels in 2020. If advanced technologies that boost efficiency and environmental performance can be successfully developed and deployed, the US can continue to depend upon its rich resources of fossil fuels.

NONE

1998-03-01T23:59:59.000Z

459

Benefits and Costs of Hydrogen Fuels  

E-Print Network (OSTI)

Processor Herbaceous Biomass Woody Biomass Petroleum Natural Gas Flared Gas Natural Gas #12;Production/Compression Pathways Gaseous H2 Liquid H2 Centralized Decentralized Electricity Methanol Flared Gas Landfill Gas Are Key Steps for Gaseous H2 NA NG Recovery (97.5%) Compressed G.H2 at Refueling Stations LNG Gasification

Argonne National Laboratory

460

Fuel Cost Estimation for Sumatra Grid System  

Science Conference Proceedings (OSTI)

Sumatra has a high growth rate electricity energy demand from the first decade in this century. At the medium of this decade the growth is 11% per annum. On the other side capability of Government of Indonesia cq. PLN authority is limited

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fuel costs labor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Advanced fuel cells and their future market  

Science Conference Proceedings (OSTI)

The advantages of fuel cells over competing technologies are outlined. These include higher fuel-efficiency (and thus lower fuel costs) and financial credits that may help reduce the effective introductory capital costs and thus help broaden the market. The credits for fuel cells result from their modularity, relative independence of efficiency on size and load, dispersibility, and rapid installation time. The fuel cell of primary interest in the United States and Japan is the PAFC (whose operation is limited by materials problems to ca. 200{degrees}C), because it is the most highly developed for use with natural gas or clean light distillate fuels. Competing fuel cell (FC) technologies are the alkaline fuel cell (AFC, limited to 80{degrees}C if inexpensive construction materials are used), the molten carbonate fuel cell (MCFC, 650{degrees}C), and the solid oxide fuel cell (SOFC, 1000{degrees}C). The author focuses on the MCFC in this paper.

Appleby, A.J. (Electric Power Research Inst., Palo Alto, CA (US))

1988-01-01T23:59:59.000Z

462

Hydrogen & Fuel Cells - Fuel Cell - Polymer Electrolyte  

NLE Websites -- All DOE Office Websites (Extended Search)

Polymer Electrolyte Fuel Cell Research Polymer Electrolyte Fuel Cell Research Xiaoping Wang measures the stability of a platinum cathode electrocatalyst. Xiaoping Wang measures the stability of a platinum cathode electrocatalyst. One of the main barriers to the commercialization of polymer electrolyte fuel cell (PEFC) systems, especially for automotive use, is the high cost of the platinum electrocatalysts. Aside from the cost of the precious metal, concern has also been raised over the adequacy of the world supply of platinum, if fuel cell vehicles were to make a significant penetration into the global automotive fleet. At Argonne, chemists are working toward the development of low-cost nonplatinum electrocatalysts for the oxygen reduction reaction--durable materials that would be stable in the fuel

463

Alternative Fuels Data Center: Alternative Fuel and Fueling Infrastructure  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Fuel and Fuel and Fueling Infrastructure Incentives to someone by E-mail Share Alternative Fuels Data Center: Alternative Fuel and Fueling Infrastructure Incentives on Facebook Tweet about Alternative Fuels Data Center: Alternative Fuel and Fueling Infrastructure Incentives on Twitter Bookmark Alternative Fuels Data Center: Alternative Fuel and Fueling Infrastructure Incentives on Google Bookmark Alternative Fuels Data Center: Alternative Fuel and Fueling Infrastructure Incentives on Delicious Rank Alternative Fuels Data Center: Alternative Fuel and Fueling Infrastructure Incentives on Digg Find More places to share Alternative Fuels Data Center: Alternative Fuel and Fueling Infrastructure Incentives on AddThis.com... More in this section... Federal State Advanced Search

464

Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Fueling  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Fuel Fuel Vehicle (AFV) and Fueling Infrastructure Loans to someone by E-mail Share Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Fueling Infrastructure Loans on Facebook Tweet about Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Fueling Infrastructure Loans on Twitter Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Fueling Infrastructure Loans on Google Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Fueling