National Library of Energy BETA

Sample records for frame develop ment

  1. Developing Low-Conductance Window Frames: Capabilities and Limitations of Current Window Heat Transfer Design Tools

    SciTech Connect (OSTI)

    Gustavsen, Arild; Arasteh, Dariush; Jelle, Bjorn Petter; Curcija, Charlie; Kohler, Christian

    2008-09-11

    While window frames typically represent 20-30% of the overall window area, their impact on the total window heat transfer rates may be much larger. This effect is even greater in low-conductance (highly insulating) windows that incorporate very low-conductance glazing. Developing low-conductance window frames requires accurate simulation tools for product research and development. Based on a literature review and an evaluation of current methods of modeling heat transfer through window frames, we conclude that current procedures specified in ISO standards are not sufficiently adequate for accurately evaluating heat transfer through the low-conductance frames. We conclude that the near-term priorities for improving the modeling of heat transfer through low-conductance frames are: (1) Add 2D view-factor radiation to standard modeling and examine the current practice of averaging surface emissivity based on area weighting and the process of making an equivalent rectangular frame cavity. (2) Asses 3D radiation effects in frame cavities and develop recommendation for inclusion into the design fenestration tools. (3) Assess existing correlations for convection in vertical cavities using CFD. (4) Study 2D and 3D natural convection heat transfer in frame cavities for cavities that are proven to be deficient from item 3 above. Recommend improved correlations or full CFD modeling into ISO standards and design fenestration tools, if appropriate. (5) Study 3D hardware short-circuits and propose methods to ensure that these effects are incorporated into ratings. (6) Study the heat transfer effects of ventilated frame cavities and propose updated correlations.

  2. MENTAL POLICY ACT IMPLE- MENTING PROCEDURES Subpart A-General

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    59 Department of Energy § 1021.102 PART 1021-NATIONAL ENVIRON- MENTAL POLICY ACT IMPLE- MENTING PROCEDURES Subpart A-General Sec. 1021.100 Purpose. 1021.101 Policy. 1021.102 Applicability. 1021.103 Adoption of CEQ NEPA regulations. 1021.104 Definitions. 1021.105 Oversight of Agency NEPA activi- ties. Subpart B-DOE Decisionmaking 1021.200 DOE planning. 1021.210 DOE decisionmaking. 1021.211 Interim actions: Limitations on ac- tions during the NEPA process. 1021.212 Research, development,

  3. Development of U-Frame Bending System for Studying the Vibration Integrity of Spent Nuclear Fuel

    SciTech Connect (OSTI)

    Wang, Hong; Wang, Jy-An John; Tan, Ting; Jiang, Hao; Cox, Thomas S; Howard, Rob L; Bevard, Bruce Balkcom; Flanagan, Michelle E

    2013-01-01

    A bending fatigue system developed to evaluate the response of spent nuclear fuel rods to vibration loads is presented. Design and analysis, fabrication, modification, calibration, and instrumentation are described. The system is composed of a U-frame testing setup for imposing bending loads on the spent fuel rod test specimen and a method for measuring the curvature of the rod during bending. The U-frame setup consists of two rigid arms, linking members, and linkages to a universal testing machine. The test specimen s curvature of bending is obtained through a three-point deflection measurement method consisting of three LVDTs mounted to the side connecting plates of the U-frame to capture the deformation of the test specimen. The system has some unique features: 1) The test specimen is installed by simple insertion using linear bearings incorporated with rigid sleeves. 2) Reverse cyclic bending tests can be carried out effectively and efficiently by push and pull at the loading point of the setup. Any test machine with a linear motion function can be used to drive the setup. 3) The embedded and preloaded linear roller bearings eliminate the backlash that exists in the conventional reverse bend tests. 4) The number of linkages between the U-frame and the universal machine is minimized. Namely, there are only two linkages needed at the two loading points of a U-frame setup, whereas a conventional four/three-point bend test frame requires four linkages. 5) The curvature measurement is immune to the effects arising from compliant layers and the rigid body motion of the machine. The compliant layers are used at the holding areas of the specimen to prevent contact damage. The tests using surrogate specimens composed of SS cladding/tube revealed several important phenomena that may cast light on the expected response of a spent fuel rod: 1) Cyclic quasi-static load (10 N/s under force control) in compressive mode (with respect to that at the loading point of the U-frame) produced increased irreversible or plastic curvature and also increased flexural rigidity of the surrogate rod. 2) Dynamic cyclic load (at least 1 Hz) in compressive mode resulted in increased flexural rigidity of the surrogate rod prior to SS cladding fracture. 3) Pellets and epoxy bonding exhibited various effects on the response of surrogate rods during the loading process as validated from static tests. 4) Dynamic cyclic load (2 Hz) in reverse mode demonstrated a substantial cyclic softening before the fracture of the surrogate rod. The degree of decrease in flexural rigidity was consistent in both measurement and on-line monitoring. The developed U-frame system is thus verified and demonstrated to be ready for further pursuit in hot-cell tests.

  4. SU-E-T-106: Development of a Collision Prediction Algorithm for Determining Problematic Geometry for SBRT Treatments Using a Stereotactic Body Frame

    SciTech Connect (OSTI)

    Wagar, M; Friesen, S; Mannarino, E

    2014-06-01

    Purpose: Collision between the gantry and the couch or patient during Radiotherapy is not a common concern for conventional RT (static fields or arc). With the increase in the application of stereotactic planning techniques to the body, collisions have become a greater concern. Non-coplanar beam geometry is desirable in stereotatic treatments in order to achieve sharp gradients and a high conformality. Non-coplanar geometry is less intuitive in the body and often requires an iterative process of planning and dry runs to guarantee deliverability. Methods: Purpose written software was developed in order to predict the likelihood of collision between the head of the gantry and the couch, patient or stereotatic body frame. Using the DICOM plan and structures set, exported by the treatment planning system, this software is able to predict the possibility of a collision. Given the plan's isocenter, treatment geometry and exterior contours, the software is able to determine if a particular beam/arc is clinically deliverable or if collision is imminent. Results: The software was tested on real world treatment plans with untreatable beam geometry. Both static non-coplanar and VMAT plans were tested. Of these, the collision prediction software could identify all as having potentially problematic geometry. Re-plans of the same cases were also tested and validated as deliverable. Conclusion: This software is capable of giving good initial indication of deliverability for treatment plans that utilize complex geometry (SBRT) or have lateral isocenters. This software is not intended to replace the standard pre-treatment QA dry run. The effectiveness is limited to those portions of the patient and immobilization devices that have been included in the simulation CT and contoured in the planning system. It will however aid the planner in reducing the iterations required to create complex treatment geometries necessary to achieve ideal conformality and organ sparing.

  5. Frame for a firearm

    DOE Patents [OSTI]

    Crandall, David L.; Watson, Richard W.

    2008-03-04

    A firearm frame which is adapted to be disposed in operative relationship as a component part of a firearm, the firearm having disposed in operative relationships each with one or more of the others, a barrel, a receiver, and at least one firing mechanism; wherein the barrel and receiver form operative parts of a movable assembly and the at least one firing mechanism is disposed in a substantially stationary operative relationship therewith; the firearm frame including at least one elongated support structure discrete from the barrel and receiver, the elongated support structure being adapted to directly support the movable assembly in an operative movable relationship therewith; whereby at least one of the barrel and receiver is in direct contact with and movable on the elongated support structure; and, a firing mechanism support structure connected to the at least one elongated support structure, the firing mechanism support structure being adapted to have the firing mechanism connected thereto; the firearm frame also directly supporting the movable assembly and the firing mechanism in corresponding movable and stationary operative relationships each with the other.

  6. Ekwi&ment Systems Divison Mr. James W. Wagoner II FDSRAP Program Manager

    Office of Legacy Management (LM)

    JQ?& Oak R,idge kssociated c5cYJ " POST Ofim Bar 1 i 7 Unwersltles Oaks Rdye. Twmessee 37E31-0: 17 February 12, 1990 Ek!rcy 1 Ekwi&ment Systems Divison Mr. James W. Wagoner II FDSRAP Program Manager Decontamination and Decommissioning Division Office of Environmental Restoration and Waste fianagement U.S. Department of Energy Washington, D.C. 20545 Subject: VISIT TO POTENTIAL SITES IN NEWARK AND LINDEN, NEW JERSEY Dear Mr. Wagoner: On February 6, 1990, while in Atlantic City to

  7. Electrically insulating and sealing frame

    DOE Patents [OSTI]

    Guthrie, Robin J. (East Hartford, CT)

    1983-11-08

    A combination gas seal and electrical insulator having a closed frame shape interconnects a fuel cell stack and a reactant gas plenum of a fuel cell generator. The frame can be of rectangular shape including at least one slidable spline connection in each side to permit expansion or contraction consistent with that of the walls of the gas plenum and fuel cell stack. The slidable spline connections in the frame sides minimizes lateral movement between the frame side members and sealing material interposed between the frame and the fuel cell stack or between the frame and the reactant gas plenum.

  8. High Performance Commercial Fenestration Framing Systems

    SciTech Connect (OSTI)

    Mike Manteghi; Sneh Kumar; Joshua Early; Bhaskar Adusumalli

    2010-01-31

    A major objective of the U.S. Department of Energy is to have a zero energy commercial building by the year 2025. Windows have a major influence on the energy performance of the building envelope as they control over 55% of building energy load, and represent one important area where technologies can be developed to save energy. Aluminum framing systems are used in over 80% of commercial fenestration products (i.e. windows, curtain walls, store fronts, etc.). Aluminum framing systems are often required in commercial buildings because of their inherent good structural properties and long service life, which is required from commercial and architectural frames. At the same time, they are lightweight and durable, requiring very little maintenance, and offer design flexibility. An additional benefit of aluminum framing systems is their relatively low cost and easy manufacturability. Aluminum, being an easily recyclable material, also offers sustainable features. However, from energy efficiency point of view, aluminum frames have lower thermal performance due to the very high thermal conductivity of aluminum. Fenestration systems constructed of aluminum alloys therefore have lower performance in terms of being effective barrier to energy transfer (heat loss or gain). Despite the lower energy performance, aluminum is the choice material for commercial framing systems and dominates the commercial/architectural fenestration market because of the reasons mentioned above. In addition, there is no other cost effective and energy efficient replacement material available to take place of aluminum in the commercial/architectural market. Hence it is imperative to improve the performance of aluminum framing system to improve the energy performance of commercial fenestration system and in turn reduce the energy consumption of commercial building and achieve zero energy building by 2025. The objective of this project was to develop high performance, energy efficient commercial fenestration framing systems, by investigating new technologies that would improve the thermal performance of aluminum frames, while maintaining their structural and life-cycle performance. The project targeted an improvement of over 30% (whole window performance) over conventional commercial framing technology by improving the performance of commercial framing systems.

  9. Advanced House Framing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Design » Design for Efficiency » Advanced House Framing Advanced House Framing Two-story home using advanced framing techniques. Two-story home using advanced framing techniques. Advanced house framing, sometimes called optimum value engineering (OVE), refers to framing techniques designed to reduce the amount of lumber used and waste generated in the construction of a wood-framed house. These techniques boost energy efficiency by replacing lumber with insulation material while maintaining the

  10. Examining the Linkage Between FRAMES and GMS

    SciTech Connect (OSTI)

    Whelan, Gene; Castleton, Karl J.

    2006-02-13

    Because GMS provides so many features, of which some are also addressed by FRAMES, it could represent a platform to link to FRAMES, or FRAMES could represent a platform to link to GMS. The focus of this summary is to examine the strengths and weaknesses of the potential linkage direction and provide recommendations for the linkage between FRAMES and GMS.

  11. Ultra-fast framing camera tube

    DOE Patents [OSTI]

    Kalibjian, Ralph (1051 Batavia Ave., Livermore, CA 94550)

    1981-01-01

    An electronic framing camera tube features focal plane image dissection and synchronized restoration of the dissected electron line images to form two-dimensional framed images. Ultra-fast framing is performed by first streaking a two-dimensional electron image across a narrow slit, thereby dissecting the two-dimensional electron image into sequential electron line images. The dissected electron line images are then restored into a framed image by a restorer deflector operated synchronously with the dissector deflector. The number of framed images on the tube's viewing screen is equal to the number of dissecting slits in the tube. The distinguishing features of this ultra-fast framing camera tube are the focal plane dissecting slits, and the synchronously-operated restorer deflector which restores the dissected electron line images into a two-dimensional framed image. The framing camera tube can produce image frames having high spatial resolution of optical events in the sub-100 picosecond range.

  12. Fabric panel clean change-out frame

    DOE Patents [OSTI]

    Brown, Ronald M.

    1995-01-31

    A fabric panel clean change-out frame, for use on a containment structure having rigid walls, is formed of a compression frame and a closure panel. The frame is formed of elongated spacers, each carrying a plurality of closely spaced flat springs, and each having a hooked lip extending on the side of the spring facing the spacer. The closure panel is includes a perimeter frame formed of flexible, wedge-shaped frame members that are receivable under the springs to deflect the hooked lips. A groove on the flexible frame members engages the hooked lips and locks the frame members in place under the springs. A flexible fabric panel is connected to the flexible frame members and closes its center.

  13. Rest frame of bubble nucleation

    SciTech Connect (OSTI)

    Garriga, Jaume; Kanno, Sugumi; Tanaka, Takahiro E-mail: sugumi@cosmos.phy.tufts.edu

    2013-06-01

    Vacuum bubbles nucleate at rest with a certain critical size and subsequently expand. But what selects the rest frame of nucleation? This question has been recently addressed in [1] in the context of Schwinger pair production in 1+1 dimensions, by using a model detector in order to probe the nucleated pairs. The analysis in [1] showed that, for a constant external electric field, the adiabatic ''in'' vacuum of charged particles is Lorentz invariant, (and in this) case pairs tend to nucleate preferentially at rest with respect to the detector. Here, we sharpen this picture by showing that the typical relative velocity between the frame of nucleation and that of the detector is at most of order ?v ? S{sub E}{sup ?1/3} << 1. Here, S{sub E} >> 1 is the action of the instanton describing pair creation. The bound ?v coincides with the minimum uncertainty in the velocity of a non-relativistic charged particle embedded in a constant electric field. A velocity of order ?v is reached after a time interval of order ?t ? S{sub E}{sup ?1/3}r{sub 0} << r{sub 0} past the turning point in the semiclassical trajectory, where r{sub 0} is the size of the instanton. If the interaction takes place in the vicinity of the turning point, the semiclassical description of collision does not apply. Nonetheless, we find that even in this case there is still a strong asymmetry in the momentum transferred from the nucleated particles to the detector, in the direction of expansion after the turning point. We conclude that the correlation between the rest frame of nucleation and that of the detector is exceedingly sharp.

  14. Advanced Framing Systems and Packages - Building America Top...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Framing Systems and Packages - Building America Top Innovation Advanced Framing Systems and Packages - Building America Top Innovation This photo shows advanced framing ...

  15. Coincidence ion imaging with a fast frame camera

    SciTech Connect (OSTI)

    Lee, Suk Kyoung; Cudry, Fadia; Lin, Yun Fei; Lingenfelter, Steven; Winney, Alexander H.; Fan, Lin; Li, Wen

    2014-12-15

    A new time- and position-sensitive particle detection system based on a fast frame CMOS (complementary metal-oxide semiconductors) camera is developed for coincidence ion imaging. The system is composed of four major components: a conventional microchannel plate/phosphor screen ion imager, a fast frame CMOS camera, a single anode photomultiplier tube (PMT), and a high-speed digitizer. The system collects the positional information of ions from a fast frame camera through real-time centroiding while the arrival times are obtained from the timing signal of a PMT processed by a high-speed digitizer. Multi-hit capability is achieved by correlating the intensity of ion spots on each camera frame with the peak heights on the corresponding time-of-flight spectrum of a PMT. Efficient computer algorithms are developed to process camera frames and digitizer traces in real-time at 1 kHz laser repetition rate. We demonstrate the capability of this system by detecting a momentum-matched co-fragments pair (methyl and iodine cations) produced from strong field dissociative double ionization of methyl iodide.

  16. Integrated seat frame and back support

    DOE Patents [OSTI]

    Martin, Leo

    1999-01-01

    An integrated seating device comprises a seat frame having a front end and a rear end. The seat frame has a double wall defining an exterior wall and an interior wall. The rear end of the seat frame has a slot cut therethrough both the exterior wall and the interior wall. The front end of the seat frame has a slot cut through just the interior wall thereof. A back support comprising a generally L shape has a horizontal member, and a generally vertical member which is substantially perpendicular to the horizontal member. The horizontal member is sized to be threaded through the rear slot and is fitted into the front slot. Welded slat means secures the back support to the seat frame to result in an integrated seating device.

  17. Self-aligning biaxial load frame

    DOE Patents [OSTI]

    Ward, Michael B.; Epstein, Jonathan S.; Lloyd, W. Randolph

    1994-01-01

    An self-aligning biaxial loading apparatus for use in testing the strength of specimens while maintaining a constant specimen centroid during the loading operation. The self-aligning biaxial loading apparatus consists of a load frame and two load assemblies for imparting two independent perpendicular forces upon a test specimen. The constant test specimen centroid is maintained by providing elements for linear motion of the load frame relative to a fixed crosshead, and by alignment and linear motion elements of one load assembly relative to the load frame.

  18. Self-aligning biaxial load frame

    DOE Patents [OSTI]

    Ward, M.B.; Epstein, J.S.; Lloyd, W.R.

    1994-01-18

    An self-aligning biaxial loading apparatus for use in testing the strength of specimens while maintaining a constant specimen centroid during the loading operation. The self-aligning biaxial loading apparatus consists of a load frame and two load assemblies for imparting two independent perpendicular forces upon a test specimen. The constant test specimen centroid is maintained by providing elements for linear motion of the load frame relative to a fixed cross head, and by alignment and linear motion elements of one load assembly relative to the load frame. 3 figures.

  19. Advanced House Framing | Department of Energy

    Office of Environmental Management (EM)

    integrity of the home. Advanced framing improves the whole-wall R-value by reducing thermal bridging (thermal flow that occurs when materials that are poor insulators displace...

  20. State-of-the-Art Highly Insulating Window Frames - Research and Market Review

    SciTech Connect (OSTI)

    Gustavsen, Arild; Jelle, Bjorn Petter; Arasteh, Dariush; Kohler, Christian

    2007-01-01

    This document reports the findings of a market and research review related to state-of-the-art highly insulating window frames. The market review focuses on window frames that satisfy the Passivhaus requirements (window U-value less or equal to 0.8 W/m{sup 2}K ), while other examples are also given in order to show the variety of materials and solutions that may be used for constructing window frames with a low thermal transmittance (U-value). The market search shows that several combinations of materials are used in order to obtain window frames with a low U-value. The most common insulating material seems to be Polyurethane (PUR), which is used together with most of the common structural materials such as wood, aluminum, and PVC. The frame research review also shows examples of window frames developed in order to increase the energy efficiency of the frames and the glazings which the frames are to be used together with. The authors find that two main tracks are used in searching for better solutions. The first one is to minimize the heat losses through the frame itself. The result is that conductive materials are replaced by highly thermal insulating materials and air cavities. The other option is to reduce the window frame area to a minimum, which is done by focusing on the net energy gain by the entire window (frame, spacer and glazing). Literature shows that a window with a higher U-value may give a net energy gain to a building that is higher than a window with a smaller U-value. The net energy gain is calculated by subtracting the transmission losses through the window from the solar energy passing through the windows. The net energy gain depends on frame versus glazing area, solar factor, solar irradiance, calculation period and U-value. The frame research review also discusses heat transfer modeling issues related to window frames. Thermal performance increasing measures, surface modeling, and frame cavity modeling are among the topics discussed. The review shows that the current knowledge gives the basis for improving the calculation procedures in the calculation standards. At the same time it is room for improvement within some areas, e.g. to fully understand the natural convection effects inside irregular vertical frame cavities (jambs) and ventilated frame cavities.

  1. SolarFrameWorks Co | Open Energy Information

    Open Energy Info (EERE)

    SolarFrameWorks Co Place: Denver, Colorado Zip: 80202 Product: This company provides framing and mounting systems to the PV industry. References: SolarFrameWorks Co1 This...

  2. Modeling laser wakefield accelerators in a Lorentz boosted frame

    SciTech Connect (OSTI)

    Vay, J.-L.; Geddes, C.G.R.; Cormier-Michel, E.; Grote, D.P.

    2010-09-15

    Modeling of laser-plasma wakefield accelerators in an optimal frame of reference [1] is shown to produce orders of magnitude speed-up of calculations from first principles. Obtaining these speedups requires mitigation of a high frequency instability that otherwise limits effectiveness in addition to solutions for handling data input and output in a relativistically boosted frame of reference. The observed high-frequency instability is mitigated using methods including an electromagnetic solver with tunable coefficients, its extension to accomodate Perfectly Matched Layers and Friedman's damping algorithms, as well as an efficient large bandwidth digital filter. It is shown that choosing theframe of the wake as the frame of reference allows for higher levels of filtering and damping than is possible in other frames for the same accuracy. Detailed testing also revealed serendipitously the existence of a singular time step at which the instability level is minimized, independently of numerical dispersion, thus indicating that the observed instability may not be due primarily to Numerical Cerenkov as has been conjectured. The techniques developed for Cerenkov mitigation prove nonetheless to be very efficient at controlling the instability. Using these techniques, agreement at the percentage level is demonstrated between simulations using different frames of reference, with speedups reaching two orders of magnitude for a 0.1 GeV class stages. The method then allows direct and efficient full-scale modeling of deeply depleted laser-plasma stages of 10 GeV-1 TeV for the first time, verifying the scaling of plasma accelerators to very high energies. Over 4, 5 and 6 orders of magnitude speedup is achieved for the modeling of 10 GeV, 100 GeV and 1 TeV class stages, respectively.

  3. Safety Culture - Discussion framing - Dirk Dunning, Issue Manager

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    September 23, 2015 Safety Culture - Discussion framing - Dirk Dunning, Issue Manager Safety Culture The Hanford Advisory Board has made several attempts at crafting and providing advice on the topic of Safety Culture. The resulting changes have not addressed the root issues and have been far less than desired. The purpose of this discussion is to start at the beginning of why "Safety Culture" as a phrase and topic exists, to develop a common understanding among Committee and Board

  4. Microlens frames for laser diode arrays

    DOE Patents [OSTI]

    Skidmore, J.A.; Freitas, B.L.

    1999-07-13

    Monolithic microlens frames enable the fabrication of monolithic laser diode arrays and are manufactured inexpensively with high registration, and with inherent focal length compensation for any lens diameter variation. A monolithic substrate is used to fabricate a low-cost microlens array. The substrate is wet-etched or sawed with a series of v-grooves. The v-grooves can be created by wet-etching, by exploiting the large etch-rate selectivity of different crystal planes. The v-grooves provide a support frame for either cylindrical or custom-shaped microlenses. Because the microlens frames are formed by photolithographic semiconductor batch-processing techniques, they can be formed inexpensively over large areas with precise lateral and vertical registration. The v-groove has an important advantage for preserving the correct focus for lenses of varying diameter. 12 figs.

  5. Microlens frames for laser diode arrays

    DOE Patents [OSTI]

    Skidmore, Jay A.; Freitas, Barry L.

    1999-01-01

    Monolithic microlens frames enable the fabrication of monolithic laser diode arrays and are manufactured inexpensively with high registration, and with inherent focal length compensation for any lens diameter variation. A monolithic substrate is used to fabricate a low-cost microlens array. The substrate is wet-etched or sawed with a series of v-grooves. The v-grooves can be created by wet-etching, by exploiting the large etch-rate selectivity of different crystal planes. The v-grooves provide a support frame for either cylindrical or custom-shaped microlenses. Because the microlens frames are formed by photolithographic semiconductor batch-processing techniques, they can be formed inexpensively over large areas with precise lateral and vertical registration. The v-groove has an important advantage for preserving the correct focus for lenses of varying diameter.

  6. FRAMES-2.0 Software System: Frames 2.0 Pest Integration (F2PEST)

    SciTech Connect (OSTI)

    Castleton, Karl J.; Meyer, Philip D.

    2009-06-17

    The implementation of the FRAMES 2.0 F2PEST module is described, including requirements, design, and specifications of the software. This module integrates the PEST parameter estimation software within the FRAMES 2.0 environmental modeling framework. A test case is presented.

  7. Experimental and Numerical Examination of the Thermal Transmittance of High Performance Window Frames

    SciTech Connect (OSTI)

    Gustavsen Ph.D., Arild; Goudey, Howdy; Kohler, Christian; Arasteh P.E., Dariush; Uvslokk, Sivert; Talev, Goce; Petter Jelle Ph.D., Bjorn

    2010-06-17

    While window frames typically represent 20-30percent of the overall window area, their impact on the total window heat transfer rates may be much larger. This effect is even greater in low-conductance (highly insulating) windows which incorporate very low conductance glazings. Developing low-conductance window frames requires accurate simulation tools for product research and development. The Passivhaus Institute in Germany states that windows (glazing and frames, combined) should have U-values not exceeding 0.80 W/(m??K). This has created a niche market for highly insulating frames, with frame U-values typically around 0.7-1.0 W/(m2 cdot K). The U-values reported are often based on numerical simulations according to international simulation standards. It is prudent to check the accuracy of these calculation standards, especially for high performance products before more manufacturers begin to use them to improve other product offerings. In this paper the thermal transmittance of five highly insulating window frames (three wooden frames, one aluminum frame and one PVC frame), found from numerical simulations and experiments, are compared. Hot box calorimeter results are compared with numerical simulations according to ISO 10077-2 and ISO 15099. In addition CFD simulations have been carried out, in order to use the most accurate tool available to investigate the convection and radiation effects inside the frame cavities. Our results show that available tools commonly used to evaluate window performance, based on ISO standards, give good overall agreement, but specific areas need improvement.

  8. Advanced Framing Systems and Packages - Building America Top Innovation |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Advanced Framing Systems and Packages - Building America Top Innovation Advanced Framing Systems and Packages - Building America Top Innovation This photo shows advanced framing technique above a window. Building America field studies involving thousands of homes have documented significant material, labor, and energy savings when production builders implement advanced framing techniques. Advanced framing can reduce the number of studs in the walls by up to one-third,

  9. Quantum chaos and order based on classically moving reference frames

    SciTech Connect (OSTI)

    Hai Wenhua [Department of Physics, Hunan Normal University, Changsha 410081 (China); Department of Physics, Jishou University, Jishou 416000, Hunan (China); Xie Qiongtao; Fang Jianshu [Department of Physics, Hunan Normal University, Changsha 410081 (China)

    2005-07-15

    We develop a mathematically consistent approach for treating the quantum systems based on moving classical reference frames. The classical and quantum exact solutions show excellently classical-quantum correspondence, in which the quantum chaotic coherent states correspond to the classically chaotic motions. Applying the approach to the periodically driven linear and nonlinear oscillators, the regular and chaotic quantum states and quantum levels, and the quantum chaotic regions are evidenced. The results indicate that chaos may cause the collapse of matter wave packets and suppress the quantum effect of energy.

  10. Safety Culture - Discussion framing - Dirk Dunning, Lead Issue Manager

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    February 4, 2016 draft Rev 5 Safety Culture - Discussion framing - Dirk Dunning, Lead Issue Manager Safety Culture The Hanford Advisory Board has made several attempts at crafting and providing advice on the topic of Safety Culture. The resulting changes have not addressed the root issues and have been far less effective than desired. The purpose of this discussion is to start at the beginning of why "Safety Culture" as a phrase and topic exists, to develop a common understanding among

  11. ARS 41-1072 Licensing Time Frames | Open Energy Information

    Open Energy Info (EERE)

    1-1072 Licensing Time Frames Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- StatuteStatute: ARS 41-1072 Licensing Time FramesLegal Abstract...

  12. Modeling Laser Wakefield Accelerators in a Lorentz Boosted Frame

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lorentz Boosted Frame VayBoost.gif An image showing the "boosted frame," in which the observer moves at near light speed. The laser pulse is represented in blue and red; the...

  13. Condensation analysis for plate-frame heat exchangers

    SciTech Connect (OSTI)

    Arman, B.; Rabas, T.J.

    1995-07-01

    A theoretical analysis is presented to predict single component and binary-mixture condensation in plate-frame heat exchangers. A thermodynamic property model based on the Peng-Robinson equation of state was developed for the binary-mixture equilibrium and formulated into a performance prediction program. A set of equations was formulated and a calculation algorithm was developed to predict the local rate of heat and mass transfer for binary mixtures. Friction-factor and heat-transfer-coefficient correlations were developed using experimental data obtained with ammonia condensation. The role of the mass-transfer resistance associated with the condensation process were analyzed for a propane/butane mixture using two limiting cases: (1) no liquid-phase mass-transfer resistance, and (2) infinite liquid-phase mass-transfer resistance. The results show that the vapor-phase mass-transfer resistance is the controlling mechanism for binary-mixture condensation.

  14. Applying compressive sensing to TEM video: A substantial frame rate increase on any camera

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Stevens, Andrew; Kovarik, Libor; Abellan, Patricia; Yuan, Xin; Carin, Lawrence; Browning, Nigel D.

    2015-08-13

    One of the main limitations of imaging at high spatial and temporal resolution during in-situ transmission electron microscopy (TEM) experiments is the frame rate of the camera being used to image the dynamic process. While the recent development of direct detectors has provided the hardware to achieve frame rates approaching 0.1 ms, the cameras are expensive and must replace existing detectors. In this paper, we examine the use of coded aperture compressive sensing (CS) methods to increase the frame rate of any camera with simple, low-cost hardware modifications. The coded aperture approach allows multiple sub-frames to be coded and integratedmore » into a single camera frame during the acquisition process, and then extracted upon readout using statistical CS inversion. Here we describe the background of CS and statistical methods in depth and simulate the frame rates and efficiencies for in-situ TEM experiments. Depending on the resolution and signal/noise of the image, it should be possible to increase the speed of any camera by more than an order of magnitude using this approach.« less

  15. Applying compressive sensing to TEM video: A substantial frame rate increase on any camera

    SciTech Connect (OSTI)

    Stevens, Andrew; Kovarik, Libor; Abellan, Patricia; Yuan, Xin; Carin, Lawrence; Browning, Nigel D.

    2015-08-13

    One of the main limitations of imaging at high spatial and temporal resolution during in-situ transmission electron microscopy (TEM) experiments is the frame rate of the camera being used to image the dynamic process. While the recent development of direct detectors has provided the hardware to achieve frame rates approaching 0.1 ms, the cameras are expensive and must replace existing detectors. In this paper, we examine the use of coded aperture compressive sensing (CS) methods to increase the frame rate of any camera with simple, low-cost hardware modifications. The coded aperture approach allows multiple sub-frames to be coded and integrated into a single camera frame during the acquisition process, and then extracted upon readout using statistical CS inversion. Here we describe the background of CS and statistical methods in depth and simulate the frame rates and efficiencies for in-situ TEM experiments. Depending on the resolution and signal/noise of the image, it should be possible to increase the speed of any camera by more than an order of magnitude using this approach.

  16. HIGH SPEED KERR CELL FRAMING CAMERA

    DOE Patents [OSTI]

    Goss, W.C.; Gilley, L.F.

    1964-01-01

    The present invention relates to a high speed camera utilizing a Kerr cell shutter and a novel optical delay system having no moving parts. The camera can selectively photograph at least 6 frames within 9 x 10/sup -8/ seconds during any such time interval of an occurring event. The invention utilizes particularly an optical system which views and transmits 6 images of an event to a multi-channeled optical delay relay system. The delay relay system has optical paths of successively increased length in whole multiples of the first channel optical path length, into which optical paths the 6 images are transmitted. The successively delayed images are accepted from the exit of the delay relay system by an optical image focusing means, which in turn directs the images into a Kerr cell shutter disposed to intercept the image paths. A camera is disposed to simultaneously view and record the 6 images during a single exposure of the Kerr cell shutter. (AEC)

  17. High frame-rate, large field wavefront sensor

    SciTech Connect (OSTI)

    Avicola, K.; Salmon, J.T.; Brase, J.; Waltjen, K.; Presta, R.; Balch, K.S.

    1992-03-01

    A two-stage intensified 192 {times} 239 pixel imager developed by Eastman Kodak for motion analysis was used to construct a 1 kHz frame-rate Hartmann wavefront sensor. The sensor uses a monolithic array of lenslets with a focal length that is adjusted by an index fluid between the convex surface and an optical flat. The accuracy of the calculated centroid position, which is related to wavefront measurement accuracy, was obtained as a function of spot power and spot size. The sensor was then dynamically tested at a 1 kHz frame-rate with a 9 {times} 9 lenslet array and a fast steering mirror, which swept a plane wavefront across the wavefront sensor. An 8 cm diameter subaperture will provide a return signal (589 nm) level of about 1000 photons/ms using the AVLIS 1 kW laser (stretched pulse) as guide star source, which is sufficient to yield a wavefront measurement of better than {gamma}/10 rms. If an area of 6 {times} 6 pixels per Hartmann spot were allocated, this wavefront sensor could support a 32 {times} 32, or 1024, element deformable mirror.

  18. Molecular-Frame Angular Distributions of Resonant Auger Electrons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Molecular-Frame Angular Distributions of Resonant Auger Electrons Molecular-Frame Angular Distributions of Resonant Auger Electrons Print Wednesday, 27 May 2009 00:00 Molecular-frame electron angular distribution (MFAD) measurements provide access to an unprecedented level of detailed information about phenomena involving quantum coherence, such as phases of photoelectron waves, symmetry breaking in molecular dissociation, core-hole localization in molecules, and molecular double-slit

  19. GENERAL RELATIVITY DERIVATION OF BEAM REST-FRAME HAMILTONIAN.

    SciTech Connect (OSTI)

    WEI,J.

    2001-06-18

    Analysis of particle interaction in the laboratory frame of storage rings is often complicated by the fact that particle motion is relativistic, and that reference particle trajectory is curved. Rest frame of the reference particle is a convenient coordinate system to work with, within which particle motion is non-relativistic. We have derived the equations of motion in the beam rest frame from the general relativity formalism, and have successfully applied them to the analysis of crystalline beams [1].

  20. EV Everywhere Framing Workshop Report Out & Lessons Learned

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    eere.energy.gov Patrick B. Davis, Program Manager Vehicle Technologies Program EV Everywhere Framing Workshop Report Out & Lessons Learned eere.energy.gov Topic Date Location Kick-Off Framing Workshop June 21 Dearborn, MI Electric Drive Components July 24-25 Chicago, IL Advanced Batteries July 26 Chicago, IL Consumer Behavior and Charging Infrastructure July 31 - Aug 1 Los Angeles, CA Lightweight Vehicles and Structures TBD TBD * 5 workshops this summer * Framing document * Draft: Facilitate

  1. Framing Document for the Second Quadrennial Technology Review (QTR 2015)

    Broader source: Energy.gov [DOE]

    The DOE QTR 2015 Framing Document describes the Nation's energy landscape including challenges and opportunities to facilitate stakeholder engagement in the QTR process.

  2. Next Generation Advanced Framing - Building America Top Innovation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Framing Strategies DOE Zero Energy Ready Home Case Study: Charles Thomas Homes, Anna Model, Omaha, NE Top Innovation Categories Advanced Technologies House as a System ...

  3. EV Everywhere Framing Workshop Report Out & Lessons Learned ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Report Out & Lessons Learned EV Everywhere Framing Workshop Report Out & Lessons Learned Presentation given at the EV Everywhere Grand Challenge: Battery Workshop on July 26, 2012 ...

  4. Next Generation Advanced Framing- Building America Top Innovation

    Broader source: Energy.gov [DOE]

    Building America researchers garnered a Top Innovation award for research into simple, cost-effective ways to implement advanced framing techniques.

  5. EV Everywhere Framing Workshop - Report Out & Lessons Learned | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy - Report Out & Lessons Learned EV Everywhere Framing Workshop - Report Out & Lessons Learned Presentation given at the EV Everywhere Grand Challenge : Electric Drive (Power Electronics and Electric Machines) Workshop on July 24, 2012 held at the Doubletree O'Hare, Chicago, IL. PDF icon 2_davis_ed.pdf More Documents & Publications EV Everywhere Framing Workshop

  6. Means to flexibly attach lens frames to temple members

    DOE Patents [OSTI]

    Smith, Harry D.

    1995-01-01

    The invention is a band hinge for flexibly connecting the temple member to the lens frame thereby preventing damage from inadvertent pressure or cyclic wear. A distinguishing feature of the invention is the use of a band hinge that holds together the temple member and the lens frame without the use of a pin or screw hinging mechanism. The invention allows for a high degree of freedom of movement for the temple member with respect to the lens frame which will prevent most forms of damages to the glasses from these types of events.

  7. Contrast from rotating frame relaxation by adiabatic pulses

    DOE Patents [OSTI]

    Michaeli, Shalom; Garwood, Michael G.; Ugurbil, Kamil; Sorce, Dennis J.

    2007-10-09

    This document discusses, among other things, a system and method for modulating transverse and longitudinal relaxation time contrast in a rotating frame based on a train of radio frequency pulses.

  8. Department of Energy Quadrennial Technology Review Framing Document

    Broader source: Energy.gov (indexed) [DOE]

    Quadrennial Technology Review Framing Document http:energy.govQTR 3142011 U.S. Department of ENERGY 2 The United States Department of Energy (DOE) has initiated a review of ...

  9. Molecular-Frame Angular Distributions of Resonant Auger Electrons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Molecular-Frame Angular Distributions of Resonant Auger Electrons Print Molecular-frame electron angular distribution (MFAD) measurements provide access to an unprecedented level of detailed information about phenomena involving quantum coherence, such as phases of photoelectron waves, symmetry breaking in molecular dissociation, core-hole localization in molecules, and molecular double-slit interference, all of which are hidden in conventional gas-phase electron spectroscopy, owing to the

  10. Molecular-Frame Angular Distributions of Resonant Auger Electrons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Molecular-Frame Angular Distributions of Resonant Auger Electrons Print Molecular-frame electron angular distribution (MFAD) measurements provide access to an unprecedented level of detailed information about phenomena involving quantum coherence, such as phases of photoelectron waves, symmetry breaking in molecular dissociation, core-hole localization in molecules, and molecular double-slit interference, all of which are hidden in conventional gas-phase electron spectroscopy, owing to the

  11. NNSA, LANL Complete DARHT Improvements With Successful Multi-frame

    National Nuclear Security Administration (NNSA)

    Hydrodynamic Test | National Nuclear Security Administration NNSA, LANL Complete DARHT Improvements With Successful Multi-frame Hydrodynamic Test August 10, 2010 WASHINGTON, D.C. - The National Nuclear Security Administration (NNSA) announced today that Los Alamos National Laboratory's (LANL) Dual Axis Radiographic Hydrodynamic Test (DARHT) facility has completed another successful two axis, multi-frame hydrodynamic test following a period of facility maintenance and several key facility and

  12. Molecular-Frame Angular Distributions of Resonant Auger Electrons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Molecular-Frame Angular Distributions of Resonant Auger Electrons Print Molecular-frame electron angular distribution (MFAD) measurements provide access to an unprecedented level of detailed information about phenomena involving quantum coherence, such as phases of photoelectron waves, symmetry breaking in molecular dissociation, core-hole localization in molecules, and molecular double-slit interference, all of which are hidden in conventional gas-phase electron spectroscopy, owing to the

  13. Molecular-Frame Angular Distributions of Resonant Auger Electrons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Molecular-Frame Angular Distributions of Resonant Auger Electrons Print Molecular-frame electron angular distribution (MFAD) measurements provide access to an unprecedented level of detailed information about phenomena involving quantum coherence, such as phases of photoelectron waves, symmetry breaking in molecular dissociation, core-hole localization in molecules, and molecular double-slit interference, all of which are hidden in conventional gas-phase electron spectroscopy, owing to the

  14. Molecular-Frame Angular Distributions of Resonant Auger Electrons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Molecular-Frame Angular Distributions of Resonant Auger Electrons Print Molecular-frame electron angular distribution (MFAD) measurements provide access to an unprecedented level of detailed information about phenomena involving quantum coherence, such as phases of photoelectron waves, symmetry breaking in molecular dissociation, core-hole localization in molecules, and molecular double-slit interference, all of which are hidden in conventional gas-phase electron spectroscopy, owing to the

  15. Molecular-Frame Angular Distributions of Resonant Auger Electrons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Molecular-Frame Angular Distributions of Resonant Auger Electrons Print Molecular-frame electron angular distribution (MFAD) measurements provide access to an unprecedented level of detailed information about phenomena involving quantum coherence, such as phases of photoelectron waves, symmetry breaking in molecular dissociation, core-hole localization in molecules, and molecular double-slit interference, all of which are hidden in conventional gas-phase electron spectroscopy, owing to the

  16. Validation of reference materials for uranium radiochronometry in the frame

    Office of Scientific and Technical Information (OSTI)

    of nuclear forensic investigations (Journal Article) | DOE PAGES Published Article: Validation of reference materials for uranium radiochronometry in the frame of nuclear forensic investigations « Prev Next » Title: Validation of reference materials for uranium radiochronometry in the frame of nuclear forensic investigations Authors: Varga, Z. ; Mayer, K. ; Bonamici, C. E. ; Hubert, A. ; Hutcheon, I. ; Kinman, W. ; Kristo, M. ; Pointurier, F. ; Spencer, K. ; Stanley, F. ; Steiner, R. ;

  17. External Insulation of Masonry Walls and Wood Framed Walls

    SciTech Connect (OSTI)

    Baker, P.

    2013-01-01

    The use of exterior insulation on a building is an accepted and effective means to increase the overall thermal resistance of the assembly that also has other advantages of improved water management and often increased air tightness of building assemblies. For thin layers of insulation (1 to 1 ), the cladding can typically be attached directly through the insulation back to the structure. For thicker insulation layers, furring strips have been added as a cladding attachment location. This approach has been used in the past on numerous Building America test homes and communities (both new and retrofit applications), and has been proven to be an effective and durable means to provide cladding attachment. However, the lack of engineering data has been a problem for many designers, contractors, and code officials. This research project developed baseline engineering analysis to support the installation of thick layers of exterior insulation on existing masonry and frame walls. Furthermore, water management details necessary to integrate windows, doors, decks, balconies and roofs were created to provide guidance on the integration of exterior insulation strategies with other enclosure elements.

  18. Non-minimal Higgs inflation and frame dependence in cosmology

    SciTech Connect (OSTI)

    Steinwachs, Christian F.; Kamenshchik, Alexander Yu.

    2013-02-21

    We investigate a very general class of cosmological models with scalar fields non-minimally coupled to gravity. A particular representative in this class is given by the non-minimal Higgs inflation model in which the Standard Model Higgs boson and the inflaton are described by one and the same scalar particle. While the predictions of the non-minimal Higgs inflation scenario come numerically remarkably close to the recently discovered mass of the Higgs boson, there remains a conceptual problem in this model that is associated with the choice of the cosmological frame. While the classical theory is independent of this choice, we find by an explicit calculation that already the first quantum corrections induce a frame dependence. We give a geometrical explanation of this frame dependence by embedding it into a more general field theoretical context. From this analysis, some conceptional points in the long lasting cosmological debate: 'Jordan frame vs. Einstein frame' become more transparent and in principle can be resolved in a natural way.

  19. Fuel cell repeater unit including frame and separator plate

    DOE Patents [OSTI]

    Yamanis, Jean; Hawkes, Justin R; Chiapetta, Jr., Louis; Bird, Connie E; Sun, Ellen Y; Croteau, Paul F

    2013-11-05

    An example fuel cell repeater includes a separator plate and a frame establishing at least a portion of a flow path that is operative to communicate fuel to or from at least one fuel cell held by the frame relative to the separator plate. The flow path has a perimeter and any fuel within the perimeter flow across the at least one fuel cell in a first direction. The separator plate, the frame, or both establish at least one conduit positioned outside the flow path perimeter. The conduit is outside of the flow path perimeter and is configured to direct flow in a second, different direction. The conduit is fluidly coupled with the flow path.

  20. FRAMES Software System: Linking to the Statistical Package R

    SciTech Connect (OSTI)

    Castleton, Karl J.; Whelan, Gene; Hoopes, Bonnie L.

    2006-12-11

    This document provides requirements, design, data-file specifications, test plan, and Quality Assurance/Quality Control protocol for the linkage between the statistical package R and the Framework for Risk Analysis in Multimedia Environmental Systems (FRAMES) Versions 1.x and 2.0. The requirements identify the attributes of the system. The design describes how the system will be structured to meet those requirements. The specification presents the specific modifications to FRAMES to meet the requirements and design. The test plan confirms that the basic functionality listed in the requirements (black box testing) actually functions as designed, and QA/QC confirms that the software meets the client’s needs.

  1. FRAMES User Defined Body Burden Concentration File Module Documentation

    SciTech Connect (OSTI)

    Pelton, Mitchell A.; Rutz, Frederick C.; Eslinger, Melany A.; Gelston, Gariann M.

    2001-06-01

    The Framework for Risk Analysis in Multimedia Environmental Systems (FRAMES) Body Burden Concentration File (BBF) contains time-varying, instantaneous, constituent concentrations for body burden by contaminant. This report contains the requirements for this file and will be used by software engineers and testers to ensure that the file inputs properly.

  2. Electromagnetic pump stator frame having power crossover struts

    DOE Patents [OSTI]

    Fanning, Alan W.; Olich, Eugene E.

    1995-01-01

    A stator frame for an electromagnetic pump includes a casing joined to a hub by a plurality of circumferentially spaced apart struts. At least one electrically insulated power crossover lead extends through the hub, through a crossover one of the struts, and through the casing for carrying electrical current therethrough.

  3. Building America Top Innovations 2012: Advanced Framing Systems and Packages

    SciTech Connect (OSTI)

    none,

    2013-01-01

    This Building America Top Innovations profile describes Building America research showing advanced 2x6, 24-inch on-center framing, single top plates, open headers, and 2-stud corners reduced board feet of lumber by more than 1,000 feet, cut energy use by 13%, and cut material and labor costs by more than $1,000 on a typical home.

  4. Building America Top Innovations 2013 Profile … Next Generation Advanced Framing

    Energy Savers [EERE]

    America research proves faster, smarter ways to employ three advanced framing techniques. It is well known that advanced framing techniques that reduce the amount of framing in stud-framed walls improve the thermal performance of the walls by allowing more room for insulation and reducing thermal bridging-the heat transfer that happens through wood framing that extends from the inside surface to the outside surface of the wall. Unfortunately, even though the benefits are known, builders have

  5. Quantitative studies of human cardiac metabolism by /sup 31/P rotating-frame NMR

    SciTech Connect (OSTI)

    Blackledge, M.J.; Rajagopalan, B.; Oberhaensli, R.D.; Bolas, N.M.; Styles, P.; Radda, G.K.

    1987-06-01

    The authors have developed /sup 31/P NMR spectroscopic methods to determine quantitatively relative levels of phosphorus-containing metabolites in the human myocardium. They have used localization techniques based on the rotating-frame imaging experiment and carried out the double-surface coil probe. Information is obtained from selected slices by rotating-frame depth selection and from a complete one-dimensional spectroscopic image using phase-modulated rotating-frame imaging. The methods collect biochemical information from metabolites in human heart, and they use the fact that the phosphocreatine/ATP molar ratio in skeletal muscle at rest is higher than that in working heart to demonstrate that localization ha been achieved for each investigation. The phosphocreatine/ATP molar ratio in normal human heart has been measured as 1.55 +/- 0.20 in six subjects using dept selection and as 1.53 +/- 0.25 in four subjects using spectroscopic imaging. Measurement of this ratio is expected to give a useful and reproducible index of myocardial energetics in normal and pathological states.

  6. Flavor twisted boundary conditions in the Breit frame

    SciTech Connect (OSTI)

    Jiang, F.-J.; Tiburzi, B. C.

    2008-08-01

    We use a generalization of chiral perturbation theory to account for the effects of flavor twisted boundary conditions in the Breit frame. The relevant framework for two light flavors is an SU(6|4) partially quenched theory, where the extra valence quarks differ only by their boundary conditions. Focusing on the pion electromagnetic form factor, finite volume corrections are calculated at next-to-leading order in the chiral expansion and are estimated to be small on current lattices.

  7. EV Everywhere Framing Workshop Overview | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    of Energy Challenge : Electric Drive (Power Electronics and Electric Machines) Workshop on July 24, 2012 held at the Doubletree O'Hare, Chicago, IL. PDF icon 2_davis_ed.pdf More Documents & Publications EV Everywhere Framing Workshop

    at the EV Everywhere Grand Challenge Kick-Off meeting held on June 21, 2012 at the Hyatt Regency, Dearborn, MI. PDF icon 1-sandalow.pdf More Documents & Publications EV Everywhere Consumer Acceptance and Charging Infrastructure Workshop Introduction

  8. Using FRAMES to Manage Environmental and Water Resources

    SciTech Connect (OSTI)

    Whelan, Gene; Millard, W. David; Gelston, Gariann M.; Khangaonkar, Tarang P.; Pelton, Mitch A.; Strenge, Dennis L.; Yang, Zhaoqing; Lee, Cheegwan; Sivaraman, Chitra; Stephan, Alex J.; Hoopes, Bonnie L.; Castleton, Karl J.

    2007-05-16

    The Framework for Risk Analysis in Multimedia Environmental Systems FRAMES) is decision-support middleware that provides users the ability to design software solutions for complex problems. It is a software platform that provides seamless and transparent communication between modeling components by using a multi-thematic approach to provide a flexible and holistic understanding of how environmental factors potentially affect humans and the environment. It incorporates disparate components (e.g., models, databases, and other frameworks) that integrate across scientific disciplines, allowing for tailored solutions to specific activities. This paper discusses one example application of FRAMES, where several commercialoff-the-shelf (COTS) software products are seamlessly linked into a planning and decision-support tool that helps manage water-based emergency situations and sustainable response. Multiple COTS models, including three surface water models, and a number of databases are linked through FRAMES to assess the impact of three asymmetric and simultaneous events, two of which impact water resources. The asymmetric events include 1) an unconventional radioactive release into a large potable water body, 2) a conventional contaminant (oil) release into navigable waters, and 3) an instantaneous atmospheric radioactive release.

  9. Universal cell frame for high-pressure water electrolyzer and electrolyzer including the same

    DOE Patents [OSTI]

    Schmitt, Edwin W.; Norman, Timothy J.

    2013-01-08

    Universal cell frame generic for use as an anode frame and as a cathode frame in a water electrolyzer. According to one embodiment, the universal cell frame includes a unitary annular member having a central opening. Four trios of transverse openings are provided in the annular member, each trio being spaced apart by about 90 degrees. A plurality of internal radial passageways fluidly interconnect the central opening and each of the transverse openings of two diametrically-opposed trios of openings, the other two trios of openings lacking corresponding radial passageways. Sealing ribs are provided on the top and bottom surfaces of the annular member. The present invention is also directed at a water electrolyzer that includes two such cell frames, one being used as the anode frame and the other being used as the cathode frame, the cathode frame being rotated 90 degrees relative to the anode frame.

  10. AAC R17-1-102 Licensing Time Frames | Open Energy Information

    Open Energy Info (EERE)

    1-102 Licensing Time Frames Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: AAC R17-1-102 Licensing Time FramesLegal...

  11. Cooling air recycling for gas turbine transition duct end frame and related method

    DOE Patents [OSTI]

    Cromer, Robert Harold; Bechtel, William Theodore; Sutcu, Maz

    2002-01-01

    A method of cooling a transition duct end frame in a gas turbine includes the steps of a) directing cooling air into the end frame from a region external of the transition duct and the impingement cooling sleeve; and b) redirecting the cooling air from the end frame into the annulus between the transition duct and the impingement cooling sleeve.

  12. ARAMS/FRAMES JOINT FREQUENCY DATA (JFD) GENERATOR

    SciTech Connect (OSTI)

    Droppo, James G.; Pelton, Mitch A.

    2006-10-04

    An ARAMS/FRAMES utility entitled ''Joint Frequency Data (JFD) Generator'' provides the capability of creating joint frequency tables. The resultant JFD tables contain summaries of the frequency of occurrence of meteorological dispersion, wind speed, and wind direction that are required as input in climatological air dispersion models. The JFD Generator computations are made by an updated version of the EPA STAR (STAbility ARray) program. Surface observations are combined with computed seasonally and diurnally varying solar flux rates to estimate the ambient atmospheric dispersion rates, represented as a stability category. The wind speeds and directions are obtained directly from the hourly surface observation data. The product is a file in a format that can be directly read by an air dispersion model. The JFD Generator can input hourly meteorological surface observation data in CD-144, Samson, and SCRAM data formats. An enhanced joint frequency table file that can be read directly by the ARAMS/FRAMES interface is produced. The output file has a format can be used by the MEPAS air dispersion program or can be modified for input to other models requiring joint frequency input.

  13. Investigating Uncertainty and Sensitivity in Integrated, Multimedia Environmental Models: Tools for FRAMES-3MRA

    SciTech Connect (OSTI)

    Babendreier, Justin E.; Castleton, Karl J.

    2005-08-01

    Elucidating uncertainty and sensitivity structures in environmental models can be a difficult task, even for low-order, single-medium constructs driven by a unique set of site-specific data. Quantitative assessment of integrated, multimedia models that simulate hundreds of sites, spanning multiple geographical and ecological regions, will ultimately require a comparative approach using several techniques, coupled with sufficient computational power. The Framework for Risk Analysis in Multimedia Environmental Systems - Multimedia, Multipathway, and Multireceptor Risk Assessment (FRAMES-3MRA) is an important software model being developed by the United States Environmental Protection Agency for use in risk assessment of hazardous waste management facilities. The 3MRA modeling system includes a set of 17 science modules that collectively simulate release, fate and transport, exposure, and risk associated with hazardous contaminants disposed of in land-based waste management units (WMU) .

  14. Overview of the ARGOS X-ray framing camera for Laser MegaJoule

    SciTech Connect (OSTI)

    Trosseille, C. Aubert, D.; Auger, L.; Bazzoli, S.; Brunel, P.; Burillo, M.; Chollet, C.; Jasmin, S.; Maruenda, P.; Moreau, I.; Oudot, G.; Raimbourg, J.; Soullié, G.; Stemmler, P.; Zuber, C.; Beck, T.; Gazave, J.

    2014-11-15

    Commissariat à l’Énergie Atomique et aux Énergies Alternatives has developed the ARGOS X-ray framing camera to perform two-dimensional, high-timing resolution imaging of an imploding target on the French high-power laser facility Laser MegaJoule. The main features of this camera are: a microchannel plate gated X-ray detector, a spring-loaded CCD camera that maintains proximity focus in any orientation, and electronics packages that provide remotely-selectable high-voltages to modify the exposure-time of the camera. These components are integrated into an “air-box” that protects them from the harsh environmental conditions. A miniaturized X-ray generator is also part of the device for in situ self-testing purposes.

  15. Performance of an LPD prototype detector at MHz frame rates under...

    Office of Scientific and Technical Information (OSTI)

    at MHz frame rates under Synchrotron and FEL radiation Authors: Koch, Andreas ; Hart, Matthew ; Nicholls, Tim ; Angelsen, Christian ; Coughlan, John ; French, Marcus ;...

  16. Building America Top Innovations 2013 Profile – Next Generation Advanced Framing

    SciTech Connect (OSTI)

    none,

    2013-09-01

    This Top Innovation profile documents faster, smarter ways to employ three advanced framing techniques: continuous drywall, rim joist headers, and continuous sheathing for raised heel trusses.

  17. DOE Grant DEFG02-95ER25253 Final Report Development of Simulation Tools for Virus Shell Assembly

    Office of Scientific and Technical Information (OSTI)

    i . ? 1 r DOE Grant DEFG02-95ER25253 Final Report Development of Simulation Tools for Virus Shell Assembly Bonnie Berger Introduction Prof. Berger's major areas of research have been in applying computational and mathematical tech- niques to problems in biology, and more specifically to problems in protein folding and genomics. Significant progress has been made in the following areas relating to virus shell assembly: develop- ment has been progressing on a second-generation self-assembly

  18. A Possible Approach to Inclusion of Space and Time in Frame Fields of Quantum Representations of Real and Complex Numbers

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Benioff, Paul

    2009-01-01

    Tmore » his work is based on the field of reference frames based on quantum representations of real and complex numbers described in other work. Here frame domains are expanded to include space and time lattices. Strings of qukits are described as hybrid systems as they are both mathematical and physical systems. As mathematical systems they represent numbers. As physical systems in each frame the strings have a discrete Schrodinger dynamics on the lattices.he frame field has an iterative structure such that the contents of a stage j frame have images in a stage j - 1 (parent) frame. A discussion of parent frame images includes the proposal that points of stage j frame lattices have images as hybrid systems in parent frames.he resulting association of energy with images of lattice point locations, as hybrid systems states, is discussed. Representations and images of other physical systems in the different frames are also described.« less

  19. Viscous-Fluid-Spring Damper Retrofit of a Steel Moment Frame Structure

    SciTech Connect (OSTI)

    Hussain, Saif; Van Benschoten, Paul; Al Satari, Mohamed; Lin, Silian

    2008-07-08

    The subject building is a peculiar pre-Northridge steel moment resisting frame building. Upon investigating the existing lateral resisting system, numerous significant deficiencies were identified; inherent lack of redundancy, poor geometry and inadequate stiffness of the lateral resisting system. All of which resulted in an extremely soft 5-story structure with a primary torsional mode of vibration at T{sub 1} = 5.46 s. Significant structural modifications were deemed necessary to meet the 'life-safety' performance objective as outlined in rehabilitation standards such as ASCE 41. Both increased stiffness and damping were required to adequately retrofit the building. Furthermore, adjacent building separation as well as deformation compatibility issues needed to be addressed and resolved. A three-dimensional computer model of the building was created using ETABS mathematically simulating the building's dynamic characteristics in its current condition. Multiple seismic retrofit systems were investigated such as Buckling Restrained Braced Frames (BRBF's). However, based on the performance effectiveness and constructability of the retrofit schemes studied, the Viscous-Fluid-Spring Damper (VFSD) system was proposed as the 'optimum' solution for the building. The VFSD, was chosen because it combines the relatively compact size and minimally invasive constructability with the required properties (an elastomeric spring in parallel with a nonlinear velocity dependent viscous damper). A site-specific response spectrum was developed for the Design Basis Earthquake (DBE, 475 year return period) event, and three pairs of representative earthquake horizontal ground motion time-histories were scaled to match this DBE. The proposed scheme reduced the building maximum inter-story drift ratio from 5.4% to about 1%. Similarly, the maximum roof displacement was reduced by about 70% (23'' to 7'')

  20. On the frames of spaces of finite-dimensional Lie algebras of dimension at most6

    SciTech Connect (OSTI)

    Gorbatsevich, V V

    2014-05-31

    In this paper, the frames of spaces of complex n-dimensional Lie algebras (that is, the intersections of all irreducible components of these spaces) are studied. A complete description of the frames and their projectivizations for n ? 6 is given. It is also proved that for n ? 6 the projectivizations of these spaces are simply connected. Bibliography: 7 titles.

  1. EV Everywhere Framing Workshop Report Out & Lessons Learned | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Report Out & Lessons Learned EV Everywhere Framing Workshop Report Out & Lessons Learned Presentation given at the EV Everywhere Grand Challenge: Battery Workshop on July 26, 2012 held at the Doubletree O'Hare, Chicago, IL. PDF icon 3_davis_b.pdf More Documents & Publications EV Everywhere Framing Workshop -

  2. Dose-to-water conversion for the backscatter-shielded EPID: A frame-based method to correct for EPID energy response to MLC transmitted radiation

    SciTech Connect (OSTI)

    Zwan, Benjamin J. OConnor, Daryl J.; King, Brian W.; Greer, Peter B.

    2014-08-15

    Purpose: To develop a frame-by-frame correction for the energy response of amorphous silicon electronic portal imaging devices (a-Si EPIDs) to radiation that has transmitted through the multileaf collimator (MLC) and to integrate this correction into the backscatter shielded EPID (BSS-EPID) dose-to-water conversion model. Methods: Individual EPID frames were acquired using a Varian frame grabber and iTools acquisition software then processed using in-house software developed inMATLAB. For each EPID image frame, the region below the MLC leaves was identified and all pixels in this region were multiplied by a factor of 1.3 to correct for the under-response of the imager to MLC transmitted radiation. The corrected frames were then summed to form a corrected integrated EPID image. This correction was implemented as an initial step in the BSS-EPID dose-to-water conversion model which was then used to compute dose planes in a water phantom for 35 IMRT fields. The calculated dose planes, with and without the proposed MLC transmission correction, were compared to measurements in solid water using a two-dimensional diode array. Results: It was observed that the integration of the MLC transmission correction into the BSS-EPID dose model improved agreement between modeled and measured dose planes. In particular, the MLC correction produced higher pass rates for almost all Head and Neck fields tested, yielding an average pass rate of 99.8% for 2%/2 mm criteria. A two-sample independentt-test and fisher F-test were used to show that the MLC transmission correction resulted in a statistically significant reduction in the mean and the standard deviation of the gamma values, respectively, to give a more accurate and consistent dose-to-water conversion. Conclusions: The frame-by-frame MLC transmission response correction was shown to improve the accuracy and reduce the variability of the BSS-EPID dose-to-water conversion model. The correction may be applied as a preprocessing step in any pretreatment portal dosimetry calculation and has been shown to be beneficial for highly modulated IMRT fields.

  3. FULL ELECTROMAGNETIC FEL SIMULATION VIA THE LORENTZ-BOOSTED FRAME TRANSFORMATION

    SciTech Connect (OSTI)

    Fawley, William; Vay, Jean-Luc

    2010-08-16

    Numerical electromagnetic simulation of some systems containing charged particles with highly relativistic directed motion can by speeded up by orders of magnitude by choice of the proper Lorentz-boosted frame. A particularly good application for calculation in a boosted frame isthat of short wavelength free-electron lasers (FELs) where a high energy electron beam with small fractional energy spread interacts with a static magnetic undulator. In the optimal boost frame (i.e., the ponderomotive rest frame), the red-shifted FEL radiation and blue-shifted undulator field have identical wavelengths and the number of required longitudinal grid cells and time-steps for fully electromagnetic simulation (relative to the laboratory frame) decrease by factors of gamma^2 each. In theory, boosted frame EM codes permit direct study of FEL problems for which the eikonal approximation for propagation of the radiation field and wiggler-period-averaging for the particle-field interaction may be suspect. We have adapted the WARP code to apply this method to several electromagnetic FEL problems including spontaneous emission, strong exponential gain in a seeded, single pass amplifier configuration, and emission from e-beams in undulators with multiple harmonic components. WARP has a standard relativistic macroparticle mover and a fully 3-D electromagnetic field solver. We discuss our boosted frame results and compare with those obtained using the ?standard? eikonal FEL simulation approach.

  4. The impact of cine EPID image acquisition frame rate on markerless soft-tissue tracking

    SciTech Connect (OSTI)

    Yip, Stephen Rottmann, Joerg; Berbeco, Ross

    2014-06-15

    Purpose: Although reduction of the cine electronic portal imaging device (EPID) acquisition frame rate through multiple frame averaging may reduce hardware memory burden and decrease image noise, it can hinder the continuity of soft-tissue motion leading to poor autotracking results. The impact of motion blurring and image noise on the tracking performance was investigated. Methods: Phantom and patient images were acquired at a frame rate of 12.87 Hz with an amorphous silicon portal imager (AS1000, Varian Medical Systems, Palo Alto, CA). The maximum frame rate of 12.87 Hz is imposed by the EPID. Low frame rate images were obtained by continuous frame averaging. A previously validated tracking algorithm was employed for autotracking. The difference between the programmed and autotracked positions of a Las Vegas phantom moving in the superior-inferior direction defined the tracking error (?). Motion blurring was assessed by measuring the area change of the circle with the greatest depth. Additionally, lung tumors on 1747 frames acquired at 11 field angles from four radiotherapy patients are manually and automatically tracked with varying frame averaging. ? was defined by the position difference of the two tracking methods. Image noise was defined as the standard deviation of the background intensity. Motion blurring and image noise are correlated with ? using Pearson correlation coefficient (R). Results: For both phantom and patient studies, the autotracking errors increased at frame rates lower than 4.29 Hz. Above 4.29 Hz, changes in errors were negligible with? < 1.60 mm. Motion blurring and image noise were observed to increase and decrease with frame averaging, respectively. Motion blurring and tracking errors were significantly correlated for the phantom (R = 0.94) and patient studies (R = 0.72). Moderate to poor correlation was found between image noise and tracking error with R ?0.58 and ?0.19 for both studies, respectively. Conclusions: Cine EPID image acquisition at the frame rate of at least 4.29 Hz is recommended. Motion blurring in the images with frame rates below 4.29 Hz can significantly reduce the accuracy of autotracking.

  5. Examining the Variability of Wind Power Output in the Regulation Time Frame: Preprint

    SciTech Connect (OSTI)

    Hodge, B. M.; Shedd, S.; Florita, A.

    2012-08-01

    This work examines the distribution of changes in wind power for different time scales in the regulation time frame as well as the correlation of changes in power output for individual wind turbines in a wind plant.

  6. Program for Converting C/C++ Texts to FrameMaker Representation

    Energy Science and Technology Software Center (OSTI)

    1995-06-23

    Used to insert pieces of C/C=+code into FrameMaker documents with fontified Language tokens. Different fonts can be used for different language constructions such as float, while, etc.

  7. Fast Hybrid and Monolithic CMOS Imagers in Multi-Frame Radiography

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect Fast Hybrid and Monolithic CMOS Imagers in Multi-Frame Radiography Citation Details In-Document Search Title: Fast Hybrid and Monolithic CMOS Imagers in Multi-Frame Radiography Authors: Kwiatkowski, Kris K. [1] ; Mariam, Fesseha Gebre [1] ; Merrill, Frank Edward [1] ; Morris, Christopher [1] ; Nedrow, Paul [1] ; Saunders, Alexander [1] ; Douence, Vincent [2] ; Bai, Yibin [2] + Show Author Affiliations Los Alamos National Laboratory Teledyne Imaging Sensors

  8. Building America Top Innovations Hall of Fame Profile … Advanced Framing Systems and Packages

    Energy Savers [EERE]

    studies involving thousands of homes have documented significant material, labor, and energy savings when production builders implement advanced framing techniques. Advanced framing can reduce the number of studs in the walls by up to one-third, reducing the cost of materials. and reducing the cost of labor in terms of the time it takes to handle, cut, install, drill, and attach to studs. Actual savings have exceeded $1,000 per home. Studies show the resulting improvement in thermal performance

  9. Key Elements of and Materials Performance Targets for Highly Insulating Window Frames

    SciTech Connect (OSTI)

    Gustavsen, Arild; Grynning, Steinar; Arasteh, Dariush; Jelle, Bjorn Petter; Goudey, Howdy

    2011-03-28

    The thermal performance of windows is important for energy efficient buildings. Windows typically account for about 30-50 percent of the transmission losses though the building envelope, even if their area fraction of the envelope is far less. The reason for this can be found by comparing the thermal transmittance (U-factor) of windows to the U-factor of their opaque counterparts (wall, roof and floor constructions). In well insulated buildings the U-factor of walls, roofs an floors can be between 0.1-0.2 W/(m2K). The best windows have U-values of about 0.7-1.0. It is therefore obvious that the U-factor of windows needs to be reduced, even though looking at the whole energy balance for windows (i.e. solar gains minus transmission losses) makes the picture more complex.In high performance windows the frame design and material use is of utmost importance, as the frame performance is usually the limiting factor for reducing the total window U-factor further. This paper describes simulation studies analyzing the effects on frame and edge-of-glass U-factors of different surface emissivities as well as frame material and spacer conductivities. The goal of this work is to define materials research targets for window frame components that will result in better frame thermal performance than is exhibited by the best products available on the market today.

  10. Oligomycin frames a common drug-binding site in the ATP synthase

    SciTech Connect (OSTI)

    Symersky, Jindrich; Osowski, Daniel; Walters, D. Eric; Mueller, David M.

    2015-12-01

    We report the high-resolution (1.9 {angstrom}) crystal structure of oligomycin bound to the subunit c10 ring of the yeast mitochondrial ATP synthase. Oligomycin binds to the surface of the c10 ring making contact with two neighboring molecules at a position that explains the inhibitory effect on ATP synthesis. The carboxyl side chain of Glu59, which is essential for proton translocation, forms an H-bond with oligomycin via a bridging water molecule but is otherwise shielded from the aqueous environment. The remaining contacts between oligomycin and subunit c are primarily hydrophobic. The amino acid residues that form the oligomycin-binding site are 100% conserved between human and yeast but are widely different from those in bacterial homologs, thus explaining the differential sensitivity to oligomycin. Prior genetics studies suggest that the oligomycin-binding site overlaps with the binding site of other antibiotics, including those effective against Mycobacterium tuberculosis, and thereby frames a common 'drug-binding site.' We anticipate that this drug-binding site will serve as an effective target for new antibiotics developed by rational design.

  11. X-ray Diffraction and Multi-Frame Phase Contrast Imaging Diagnostics for IMPULSE at the Advanced Photon Source

    SciTech Connect (OSTI)

    Iverson, Adam; Carlson, Carl; Young, Jason; Curtis, Alden; Jensen, Brian; Ramos, Kyle; Yeager, John; Montgomery, David; Fezza, Kamel

    2013-07-08

    The diagnostic needs of any dynamic loading platform present unique technical challenges that must be addressed in order to accurately measure in situ material properties in an extreme environment. The IMPULSE platform (IMPact system for Ultrafast Synchrotron Experiments) at the Advanced Photon Source (APS) is no exception and, in fact, may be more challenging, as the imaging diagnostics must be synchronized to both the experiment and the 60 ps wide x-ray bunches produced at APS. The technical challenges of time-resolved x-ray diffraction imaging and high-resolution multi-frame phase contrast imaging (PCI) are described in this paper. Example data from recent IMPULSE experiments are shown to illustrate the advances and evolution of these diagnostics with a focus on comparing the performance of two intensified CCD cameras and their suitability for multi-frame PCI. The continued development of these diagnostics is fundamentally important to IMPULSE and many other loading platforms and will benefit future facilities such as the Dynamic Compression Sector at APS and MaRIE at Los Alamos National Laboratory.

  12. Concepts Associated with Transferring Temporal and Spatial Boundary Conditions between Modules in the Framework for Risk Analysis in Multimedia Environmental Systems (FRAMES)

    SciTech Connect (OSTI)

    Whelan, Gene; Castleton, Karl J.; Pelton, Mitch A.

    2006-10-03

    This document describes concepts associated with transferring temporal and spatial boundary conditions between modules in FRAMES and how FRAMES might consider dynamic feedback.

  13. Comparison of the Window-Frame RHIC-abort kicker with C-type Kicker

    SciTech Connect (OSTI)

    Tsoupas, N.; Hahn, H.; Meng, W.; Severance, Michael; McMahan, Brandon

    2014-08-26

    The high intensity proton bunches (~2.5x1011 p/bunch ) circulating in RHIC increase the temperature of the ferrite-made RHIC-abort-kickers above the Curie point; as a result, the kickers cannot provide the required field to abort the beam at the beam dump. A team of experts in the CAD department worked on modifying the design of the window-frame RHIC-abort kicker to minimize the hysteresis losses responsible for the increase of the ferrite’s temperature. In this technical note we report some results from the study of two possible modifications of the window-frame RHIC-abort kicker, and we compare these results with those of a propose C-type RHIC-abort kicker. We also include an Appendix where we describe a method which may further reduce the hysteresis losses of the window-frame kicker.

  14. Rotating-frame gradient fields for magnetic resonance imaging and nuclear magnetic resonance in low fields

    DOE Patents [OSTI]

    Bouchard, Louis-Serge; Pines, Alexander; Demas, Vasiliki

    2014-01-21

    A system and method for Fourier encoding a nuclear magnetic resonance (NMR) signal is disclosed. A static magnetic field B.sub.0 is provided along a first direction. An NMR signal from the sample is Fourier encoded by applying a rotating-frame gradient field B.sub.G superimposed on the B.sub.0, where the B.sub.G comprises a vector component rotating in a plane perpendicular to the first direction at an angular frequency .omega.in a laboratory frame. The Fourier-encoded NMR signal is detected.

  15. Dissipation in a rotating frame: Master equation, effective temperature, and Lamb shift

    SciTech Connect (OSTI)

    Verso, Alvise; Ankerhold, Joachim

    2010-02-15

    Motivated by recent realizations of microwave-driven nonlinear resonators in superconducting circuits, the impact of environmental degrees of freedom is analyzed as seen from a rotating frame. A system plus reservoir model is applied to consistently derive in the weak coupling limit the master equation for the reduced density in the moving frame and near the first bifurcation threshold. The concept of an effective temperature is introduced to analyze to what extent a detailed balance relation exists. Explicit expressions are also found for the Lamb-shift. Results for ohmic baths are in agreement with experimental findings, while for structured environments population inversion is predicted that may qualitatively explain recent observations.

  16. Digital Instrumentation and Control Failure Events Derivation and Analysis by Frame-Based Technique

    SciTech Connect (OSTI)

    Hui-Wen Huang; Chunkuan Shih [National Tsing Hua University, 101, Section 2, Kuang-Fu Road, Hsinchu, Taiwan 30013 (China); Swu Yih [DML International, 18F-1 295, Section 2 Kuang Fu Road, Hsinchu, Taiwan (China); Yen-Chang Tzeng; Ming-Huei Chen [Institute of Nuclear Energy Research, No. 1000, Wunhua Rd., Jiaan Village, Longtan Township, Taoyuan County 32546, Taiwan (China)

    2006-07-01

    A frame-based technique, including physical frame, logical frame, and cognitive frame, was adopted to perform digital I and C failure events derivation and analysis for generic ABWR. The physical frame was structured with a modified PCTran-ABWR plant simulation code, which was extended and enhanced on the feedwater system, recirculation system, and steam line system. The logical model is structured with MATLAB, which was incorporated into PCTran-ABWR to improve the pressure control system, feedwater control system, recirculation control system, and automated power regulation control system. As a result, the software failure of these digital control systems can be properly simulated and analyzed. The cognitive frame was simulated by the operator awareness status in the scenarios. Moreover, via an internal characteristics tuning technique, the modified PCTran-ABWR can precisely reflect the characteristics of the power-core flow. Hence, in addition to the transient plots, the analysis results can then be demonstrated on the power-core flow map. A number of postulated I and C system software failure events were derived to achieve the dynamic analyses. The basis for event derivation includes the published classification for software anomalies, the digital I and C design data for ABWR, chapter 15 accident analysis of generic SAR, and the reported NPP I and C software failure events. The case study of this research includes (1) the software CMF analysis for the major digital control systems; and (2) postulated ABWR digital I and C software failure events derivation from the actual happening of non-ABWR digital I and C software failure events, which were reported to LER of USNRC or IRS of IAEA. These events were analyzed by PCTran-ABWR. Conflicts among plant status, computer status, and human cognitive status are successfully identified. The operator might not easily recognize the abnormal condition, because the computer status seems to progress normally. However, a well trained operator can become aware of the abnormal condition with the inconsistent physical parameters; and then can take early corrective actions to avoid the system hazard. This paper also discusses the advantage of Simulation-based method, which can investigate more in-depth dynamic behavior of digital I and C system than other approaches. Some unanticipated interactions can be observed by this method. (authors)

  17. Making Molecular Movies: 10,000,000,000,000 Frames per Second

    SciTech Connect (OSTI)

    Gaffney, Kelly

    2006-12-12

    Movies have transformed our perception of the world. With slow motion photography, we can see a hummingbird flap its wings, and a bullet pierce an apple. The remarkably small and extremely fast molecular world that determines how your body functions cannot be captured with even the most sophisticated movie camera today. To see chemistry in real time requires a camera capable of seeing molecules that are one ten billionth of a foot with a frame rate of 10 trillion frames per second! SLAC has embarked on the construction of just such a camera. Please join me as I discuss how this molecular movie camera will work and how it will change our perception of the molecular world.

  18. A multi-frame soft x-ray pinhole imaging diagnostic for single-shot applications

    SciTech Connect (OSTI)

    Wurden, G. A.; Coffey, S. K.

    2012-10-15

    For high energy density magnetized target fusion experiments at the Air Force Research Laboratory FRCHX machine, obtaining multi-frame soft x-ray images of the field reversed configuration (FRC) plasma as it is being compressed will provide useful dynamics and symmetry information. However, vacuum hardware will be destroyed during the implosion. We have designed a simple in-vacuum pinhole nosecone attachment, fitting onto a Conflat window, coated with 3.2 mg/cm{sup 2} of P-47 phosphor, and covered with a thin 50-nm aluminum reflective overcoat, lens-coupled to a multi-frame Hadland Ultra intensified digital camera. We compare visible and soft x-ray axial images of translating ({approx}200 eV) plasmas in the FRX-L and FRCHX machines in Los Alamos and Albuquerque.

  19. Byggmeister Test Home. Analysis and Initial Results of Cold Climate Wood-Framed Home Retrofit

    SciTech Connect (OSTI)

    Gates, C.

    2013-01-01

    BSC seeks to further the energy efficiency market for New England area retrofit projects by supporting projects that are based on solid building science fundamentals that will benefit the homeowner through a combination of energy savings, improved durability, and occupant comfort. This report describes a deep retrofit project of a two-family wood-framed home in Belmont, Massachusetts, and examines the retrofit measures for the enclosure amd mechanical systems and reviews the decision-making process that took place during planning.

  20. Quantum correlations of helicity entangled states in non-inertial frames beyond single mode approximation

    SciTech Connect (OSTI)

    Harsij, Zeynab Mirza, Behrouz

    2014-12-15

    A helicity entangled tripartite state is considered in which the degree of entanglement is preserved in non-inertial frames. It is shown that Quantum Entanglement remains observer independent. As another measure of quantum correlation, Quantum Discord has been investigated. It is explicitly shown that acceleration has no effect on the degree of quantum correlation for the bipartite and tripartite helicity entangled states. Geometric Quantum Discord as a HilbertSchmidt distance is computed for helicity entangled states. It is shown that living in non-inertial frames does not make any influence on this distance, either. In addition, the analysis has been extended beyond single mode approximation to show that acceleration does not have any impact on the quantum features in the limit beyond the single mode. As an interesting result, while the density matrix depends on the right and left Unruh modes, the Negativity as a measure of Quantum Entanglement remains constant. Also, Quantum Discord does not change beyond single mode approximation. - Highlights: The helicity entangled states here are observer independent in non-inertial frames. It is explicitly shown that Quantum Discord for these states is observer independent. Geometric Quantum Discord is also not affected by acceleration increase. Extending to beyond single mode does not change the degree of entanglement. Beyond single mode approximation the degree of Quantum Discord is also preserved.

  1. Ultra-high speed burst-mode imager for multi-frame radiography

    SciTech Connect (OSTI)

    Kwiatkowski, Kris; Nedrow, Paul; Mariam, Fesseha; Merrill, Frank E; Morris, Chris L; Saunders, Abdy; Hogan, Gary; Douance, Vincent; Bal, Yibin; Joshi, Atul; Auyeung, John

    2010-01-01

    A 720 x 720 pixel hybrid-CMOS imager was fabricated by Rockwell Scientific (now Teledyne Imaging Sensors). Several cameras have been in operation for 5 years, in a variety of static and dynamic experiments, at the 800MeV proton radiography (pRAD) facility at the LANSCE accelerator. The cameras can operate with a per-pulse adjustable inter-frame time of 250ns to 2s, and with an exposure/integration-time as short as 150 ns. Given the 800 ms total readout time, the imager can be externally synchronized to 0.1-to-5Hz, 50-ns wide proton beam pulses, and record 1000-frame radiographic movies of 5-to-30 minute duration. The effectiveness and dependence of the global electronic shutter on the pixelated Si photo-sensor bias voltage is discussed. The spatial resolution dependence of the full imaging system on various monolithic and structured scintillators is presented. We also present features of a new-generation 10-frame, 1024 x 1024 pixel, 50-ns exposure, 12-bit dynamic range imager, which is now in the design phase.

  2. SU-E-J-112: The Impact of Cine EPID Image Acquisition Frame Rate On Markerless Soft-Tissue Tracking

    SciTech Connect (OSTI)

    Yip, S; Rottmann, J; Berbeco, R

    2014-06-01

    Purpose: Although reduction of the cine EPID acquisition frame rate through multiple frame averaging may reduce hardware memory burden and decrease image noise, it can hinder the continuity of soft-tissue motion leading to poor auto-tracking results. The impact of motion blurring and image noise on the tracking performance was investigated. Methods: Phantom and patient images were acquired at a frame rate of 12.87Hz on an AS1000 portal imager. Low frame rate images were obtained by continuous frame averaging. A previously validated tracking algorithm was employed for auto-tracking. The difference between the programmed and auto-tracked positions of a Las Vegas phantom moving in the superior-inferior direction defined the tracking error (?). Motion blurring was assessed by measuring the area change of the circle with the greatest depth. Additionally, lung tumors on 1747 frames acquired at eleven field angles from four radiotherapy patients are manually and automatically tracked with varying frame averaging. ? was defined by the position difference of the two tracking methods. Image noise was defined as the standard deviation of the background intensity. Motion blurring and image noise were correlated with ? using Pearson correlation coefficient (R). Results: For both phantom and patient studies, the auto-tracking errors increased at frame rates lower than 4.29Hz. Above 4.29Hz, changes in errors were negligible with ?<1.60mm. Motion blurring and image noise were observed to increase and decrease with frame averaging, respectively. Motion blurring and tracking errors were significantly correlated for the phantom (R=0.94) and patient studies (R=0.72). Moderate to poor correlation was found between image noise and tracking error with R -0.58 and -0.19 for both studies, respectively. Conclusion: An image acquisition frame rate of at least 4.29Hz is recommended for cine EPID tracking. Motion blurring in images with frame rates below 4.39Hz can substantially reduce the accuracy of auto-tracking. This work is supported in part by the Varian Medical Systems, Inc.

  3. Higgs gravitational interaction, weak boson scattering, and Higgs inflation in Jordan and Einstein frames

    SciTech Connect (OSTI)

    Ren, Jing; Xianyu, Zhong-Zhi; He, Hong-Jian E-mail: xianyuzhongzhi@gmail.com

    2014-06-01

    We study gravitational interaction of Higgs boson through the unique dimension-4 operator ?H{sup }HR, with H the Higgs doublet and R the Ricci scalar curvature. We analyze the effect of this dimensionless nonminimal coupling ? on weak gauge boson scattering in both Jordan and Einstein frames. We explicitly establish the longitudinal-Goldstone equivalence theorem with nonzero ? coupling in both frames, and analyze the unitarity constraints. We study the ?-induced weak boson scattering cross sections at O(1?30) TeV scales, and propose to probe the Higgs-gravity coupling via weak boson scattering experiments at the LHC (14 TeV) and the next generation pp colliders (50-100 TeV). We further extend our study to Higgs inflation, and quantitatively derive the perturbative unitarity bounds via coupled channel analysis, under large field background at the inflation scale. We analyze the unitarity constraints on the parameter space in both the conventional Higgs inflation and the improved models in light of the recent BICEP2 data.

  4. Simulation and Experiment on Direct Continuous Casting Process of Lead Frame Copper Alloy

    SciTech Connect (OSTI)

    Huang Guojie; Xie Shuisheng; Cheng Lei [State Key Laboratory for Fabrication and Process of Nonferrous Metals, Beijing General Research Institute for Non-ferrous Metals, 100088 (China)

    2010-06-15

    Direct Continuous Casting (D.C.C) is an important method in casting lead frame copper alloy. In this paper, numerical simulation is adopted to investigate the casting process in order to optimize the D.C.C technical parameters, such as the casting temperature, casting speed and cooling intensity. According to the numerical results, the reasonable parameters are that the casting temperature is between 1413 Kapprox1413 K, the casting speed is between 8 m/happrox10 m/h and the speed of cooling water is between 4.2 m/sapprox4.6 m/s. And the depth of liquid-solid boundary is measured in different casting temperature and casting speed by experiments. The results show the actual measurements have a little deviation with the numerical simulation. The results of numerical simulation provide the significant reference to the actual experiments.

  5. X-ray Spectroscopy with Elliptical Crystals and Face-On Framing Cameras

    SciTech Connect (OSTI)

    Heeter, R; Emig, J; Fournier, K; Hansen, S; May, M; Young, B

    2004-04-16

    X-ray spectrometers using elliptically bent crystals have desirable properties for applications requiring broad spectral coverage, good spectral resolution, and minimized source broadening. Previous work used custom-positioned film or microchannel plate detectors. They find it is also useful and cost-effective to field elliptical crystals in existing snouts on the face-on gated microchannel plate framing cameras commonly used at many facilities. they numerically explored the full design space (spectral range and resolution) of elliptical crystals compatible with the new MSPEC multipurpose spectrometer snout. They have tested at the Omega laser an elliptical RAP crystal with 174 mm focal length, 0.9885 eccentricity, and 4.6 degree inclination, viewing from 1.0 to at least 1.7 keV with E/dE of 300-500. A slit (2x mag) images 3 mm sources with 70 um spatial resolution.

  6. X-ray spectroscopy with elliptical crystals and face-on framing cameras

    SciTech Connect (OSTI)

    Heeter, R.F.; Emig, J.A.; Fournier, K.B.; Hansen, S.B.; May, M.J.; Young, B.K.F.

    2004-10-01

    X-ray spectrometers using elliptically bent crystals have desirable properties for applications requiring broad spectral coverage, good spectral resolution, and minimized source broadening. Previous work used custom-positioned film or microchannel plate detectors. We find it is also useful and cost-effective to field elliptical crystals in existing snouts on the face-on gated microchannel plate framing cameras commonly used at many facilities. We numerically explored the full design space (spectral range and resolution) of elliptical crystals compatible with the new multipurpose spectrometer snout. We have tested at the Omega laser an elliptical rubidium acid phthalate crystal with 174 mm focal length, 0.9885 eccentricity, and 4.6 deg. inclination, viewing from 1.0 to at least 1.7 keV with spectral resolution E/dE of 300-500. A slit (2xmagnification) images 3 mm sources with 70 {mu}m spatial resolution.

  7. OPTICAL SPECTRA OF CANDIDATE SOUTHERN HEMISPHERE INTERNATIONAL CELESTIAL REFERENCE FRAME (ICRF) RADIO SOURCES

    SciTech Connect (OSTI)

    Titov, O.; Jauncey, D. L.; Johnston, H. M.; Hunstead, R. W.; Christensen, L.

    2011-11-15

    We present the results of spectroscopic observations of the optical counterparts of 47 southern radio sources from the candidate International Celestial Reference Catalogue as part of a very long baseline interferometry (VLBI) program to strengthen the celestial reference frame, especially in the south. We made the observations with the 3.58 m European Southern Observatory New Technology Telescope. We obtained redshifts for 30 quasars and one radio galaxy, with a further seven objects being probable BL Lac objects with featureless spectra. Of the remainder, four were clear misidentifications with Galactic stars and five had low signal-to-noise spectra and could not be classified. These results, in combination with new VLBI data of the radio sources with redshifts more than 2, add significantly to the existing data needed to refine the distribution of source proper motions over the celestial sphere.

  8. Progresses in tritium accident modelling in the frame of IAEA EMRAS II

    SciTech Connect (OSTI)

    Galeriu, D.; Melintescu, A.

    2015-03-15

    The assessment of the environmental impact of tritium release from nuclear facilities is a topic of interest in many countries. In the IAEA's Environmental Modelling for Radiation Safety (EMRAS I) programme, progresses for routine releases were done and in the EMRAS II programme a dedicated working group (WG 7 - Tritium Accidents) focused on the potential accidental releases (liquid and atmospheric pathways). The progresses achieved in WG 7 were included in a complex report - a technical document of IAEA covering both liquid and atmospheric accidental release consequences. A brief description of the progresses achieved in the frame of EMRAS II WG 7 is presented. Important results have been obtained concerning washout rate, the deposition on the soil of HTO and HT, the HTO uptake by leaves and the subsequent conversion to OBT (organically bound tritium) during daylight. Further needs of the processes understanding and the experimental efforts are emphasised.

  9. Experimental Evaluation of Beam to Diamond Box Column Connection with Through Plate in Moment Frames

    SciTech Connect (OSTI)

    Keshavarzi, Farhad; Torabian, Shahabeddin; Imanpour, Ali; Mirghaderi, Rasoul

    2008-07-08

    Moment resisting frames with built up section have very enhanced features due to high bending stiffness and strength characteristics in two principal axes and access to column faces for beam to column easy connections. But due to proper transfer of beam stresses to column faces there were always some specific controvertibly issues that how to make the load transfer through and in plane manner in order to mobilize the forces in column faces. Using diamond column instead of box column provide possibility to mobilize the load transfer mechanism in column faces. This section as a column has considerable benefit such as high plastic to elastic section modulus ratio which is an effective factor for force controlled components. Typical connection has no chance to be applied with diamond column.This paper elucidates the seismic behavior of through-plates moment connections to diamond box columns for use in steel moment resisting frames. This connection has a lot of economical benefits such as no need to horizontal continuity plates and satisfying the weak beam--strong column criteria in the connection region. They might serve as panel zone plates as well. According to high shear demand in panel zone of beam to column joint one should use the doublers plates in order to decrease the shear strength demand in this sensitive part of structure but these plates have no possibility to mobilize the load transfer mechanism in column web and transfer them to column flanges. In this type of connection, column faces have effective role in order to decrease the demands on through plate and they are impressive factors for improving the performance of the connection.Experimental analysis was conducted to elucidate the seismic behavior of this connection. The results of Experimental analysis established the effectiveness of the through plate in mitigating local stress concentrations and forming the plastic hinge zone in the beam away from the beam to column interface. The moment-rotation graphs form sub-assemblage show a desirable seismic performance of this connection.

  10. Preferred frame parameters in the tensor-vector-scalar theory of gravity and its generalization

    SciTech Connect (OSTI)

    Sagi, Eva

    2009-08-15

    The tensor-vector-scalar theory of gravity, which was designed as a relativistic implementation to the modified dynamics paradigm, has fared quite well as an alternative to dark matter, on both galactic and cosmological scales. However, its performance in the Solar System, as embodied in the post-Newtonian formalism, has not yet been fully investigated. We calculate the post-Newtonian parameters for TeVeS with the cosmological value of the scalar field taken into account, and show that in this situation the cosmological value of the scalar field is tightly linked to the vector field coupling constant K, preventing the former from evolving as predicted by its equation of motion. We show that generalizing TeVeS to have an Aether-type vector action, as suggested by Skordis, removes the aforesaid link, and this generalized version of TeVes has its {beta}, {gamma}, and {xi} parameterized post-Newtonian parameters identical to those in GR, while solar system constraints on the preferred frame parameters {alpha}{sub 1} and {alpha}{sub 2} can be satisfied within a modest range of small values of the scalar and vector fields coupling parameters, and for cosmological values of the scalar field consistent with evolution within the framework of existing cosmological models.

  11. Multimedia-modeling integration development environment

    SciTech Connect (OSTI)

    Pelton, Mitchell A.; Hoopes, Bonnie L.

    2002-09-02

    There are many framework systems available; however, the purpose of the framework presented here is to capitalize on the successes of the Framework for Risk Analysis in Multimedia Environmental Systems (FRAMES) and Multi-media Multi-pathway Multi-receptor Risk Assessment (3MRA) methodology as applied to the Hazardous Waste Identification Rule (HWIR) while focusing on the development of software tools to simplify the module developer?s effort of integrating a module into the framework.

  12. Leadership Development Series Event

    Broader source: Energy.gov [DOE]

    Frame-Breaking Leadership presented by the Carlson School of Management at the University of Minnesota. For GS 13-SES

  13. DOE Zero Energy Ready Home Case Study: StreetScape Development, LLC, Libertyville, Illinois

    SciTech Connect (OSTI)

    none,

    2013-09-01

    These single-family, HERS 45 homes incorporate 2×6 wood framed walls with R-20 open cell spray insulation and OSB. The builder, StreetScape Development, won a 2013 Housing Innovation Award in the custom builder category.

  14. Note: Effect of photodiode aluminum cathode frame on spectral sensitivity in the soft x-ray energy band

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Effect of photodiode aluminum cathode frame on spectral sensitivity in the soft x-ray energy band M. B. McGarry 1,a) , P. Franz 2 , D. J. Den Hartog 1 , J. A. Goetz 1 and J. Johnson 1 a) Electronic mail: mbmcgarry@wisc.edu Rev. Sci. Instrum. 85, 096105 (2014); http://dx.doi.org/10.1063/1.4894656 Abstract Silicon photodiodes used for soft x-ray detection typically have a thin metal electrode partially covering the active area of the photodiode, which subtly alters the spectral sensitivity of the

  15. Kinetics of liquid-mediated crystallization of amorphous Ge from multi-frame dynamic transmission electron microscopy

    SciTech Connect (OSTI)

    Santala, M. K.; Raoux, S.; Campbell, G. H.

    2015-12-24

    The kinetics of laser-induced, liquid-mediated crystallization of amorphous Ge thin films were studied using multi-frame dynamic transmission electron microscopy (DTEM), a nanosecond-scale photo-emission transmission electron microscopy technique. In these experiments, high temperature gradients are established in thin amorphous Ge films with a 12-ns laser pulse with a Gaussian spatial profile. The hottest region at the center of the laser spot crystallizes in ~100 ns and becomes nano-crystalline. Over the next several hundred nanoseconds crystallization continues radially outward from the nano-crystalline region forming elongated grains, some many microns long. The growth rate during the formation of these radial grains is measured with time-resolved imaging experiments. Crystal growth rates exceed 10 m/s, which are consistent with crystallization mediated by a very thin, undercooled transient liquid layer, rather than a purely solid-state transformation mechanism. The kinetics of this growth mode have been studied in detail under steady-state conditions, but here we provide a detailed study of liquid-mediated growth in high temperature gradients. Unexpectedly, the propagation rate of the crystallization front was observed to remain constant during this growth mode even when passing through large local temperature gradients, in stark contrast to other similar studies that suggested the growth rate changed dramatically. As a result, the high throughput of multi-frame DTEM provides gives a more complete picture of the role of temperature and temperature gradient on laser crystallization than previous DTEM experiments.

  16. Scoping and Framing Social Opposition to U.S. Wind Projects (Poster)

    SciTech Connect (OSTI)

    Lantz, E.; Flowers, L.

    2010-05-01

    Historical barriers to wind power include cost and reliability. However, rapid growth has increased the footprint of wind power in the United States, and some parts of the country have begun to observe conflicts between local communities and wind energy development. Thus, while questions of economic viability and the ability of grid operators to effectively manage wind energy have become less significant, community acceptance issues have emerged as a barrier to wind and associated transmission projects. Increasing community acceptance is likely to be a growing challenge as the wind industry seeks electricity sector penetration levels approaching 20%.

  17. Kinetics of liquid-mediated crystallization of amorphous Ge from multi-frame dynamic transmission electron microscopy

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Santala, M. K.; Raoux, S.; Campbell, G. H.

    2015-12-24

    The kinetics of laser-induced, liquid-mediated crystallization of amorphous Ge thin films were studied using multi-frame dynamic transmission electron microscopy (DTEM), a nanosecond-scale photo-emission transmission electron microscopy technique. In these experiments, high temperature gradients are established in thin amorphous Ge films with a 12-ns laser pulse with a Gaussian spatial profile. The hottest region at the center of the laser spot crystallizes in ~100 ns and becomes nano-crystalline. Over the next several hundred nanoseconds crystallization continues radially outward from the nano-crystalline region forming elongated grains, some many microns long. The growth rate during the formation of these radial grains is measuredmore » with time-resolved imaging experiments. Crystal growth rates exceed 10 m/s, which are consistent with crystallization mediated by a very thin, undercooled transient liquid layer, rather than a purely solid-state transformation mechanism. The kinetics of this growth mode have been studied in detail under steady-state conditions, but here we provide a detailed study of liquid-mediated growth in high temperature gradients. Unexpectedly, the propagation rate of the crystallization front was observed to remain constant during this growth mode even when passing through large local temperature gradients, in stark contrast to other similar studies that suggested the growth rate changed dramatically. As a result, the high throughput of multi-frame DTEM provides gives a more complete picture of the role of temperature and temperature gradient on laser crystallization than previous DTEM experiments.« less

  18. Radio-optical reference frame link using the U.S. Naval observatory astrograph and deep CCD imaging

    SciTech Connect (OSTI)

    Zacharias, N.; Zacharias, M. I.

    2014-05-01

    Between 1997 and 2004 several observing runs were conducted, mainly with the CTIO 0.9 m, to image International Celestial Reference Frame (ICRF) counterparts (mostly QSOs) in order to determine accurate optical positions. Contemporary to these deep CCD images, the same fields were observed with the U.S. Naval Observatory astrograph in the same bandpass. They provide accurate positions on the Hipparcos/Tycho-2 system for stars in the 10-16 mag range used as reference stars for the deep CCD imaging data. Here we present final optical position results of 413 sources based on reference stars obtained by dedicated astrograph observations that were reduced following two different procedures. These optical positions are compared to radio very long baseline interferometry positions. The current optical system is not perfectly aligned to the ICRF radio system with rigid body rotation angles of 3-5 mas (= 3? level) found between them for all three axes. Furthermore, statistically, the optical-radio position differences are found to exceed the total, combined, known errors in the observations. Systematic errors in the optical reference star positions and physical offsets between the centers of optical and radio emissions are both identified as likely causes. A detrimental, astrophysical, random noise component is postulated to be on about the 10 mas level. If confirmed by future observations, this could severely limit the Gaia to ICRF reference frame alignment accuracy to an error of about 0.5 mas per coordinate axis with the current number of sources envisioned to provide the link. A list of 36 ICRF sources without the detection of an optical counterpart to a limiting magnitude of about R = 22 is provided as well.

  19. Validation of reference materials for uranium radiochronometry in the frame of nuclear forensic investigations

    SciTech Connect (OSTI)

    Varga, Z.; Mayer, K.; Bonamici, C. E.; Hubert, A.; Hutcheon, I.; Kinman, W.; Kristo, M.; Pointurier, F.; Spencer, K.; Stanley, F.; Steiner, R.; Tandon, L.; Williams, R.

    2015-05-11

    The results of a joint effort by expert nuclear forensic laboratories in the area of age dating of uranium, i.e. the elapsed time since the last chemical purification of the material are presented and discussed. Completely separated uranium materials of known production date were distributed among the laboratories, and the samples were dated according to routine laboratory procedures by the measurement of the ²²⁰Th/²³⁴U ratio. The measurement results were in good agreement with the known production date showing that the concept for preparing uranium age dating reference material based on complete separation is valid. Detailed knowledge of the laboratory procedures used for uranium age dating allows the identification of possible improvements in the current protocols and the development of improved practice in the future. The availability of age dating reference materials as well as the evolvement of the age dating best-practice protocol will increase the relevance and applicability of age dating as part of the tool-kit available for nuclear forensic investigations.

  20. Validation of reference materials for uranium radiochronometry in the frame of nuclear forensic investigations

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Varga, Z.; Mayer, K.; Bonamici, C. E.; Hubert, A.; Hutcheon, I.; Kinman, W.; Kristo, M.; Pointurier, F.; Spencer, K.; Stanley, F.; et al

    2015-05-11

    The results of a joint effort by expert nuclear forensic laboratories in the area of age dating of uranium, i.e. the elapsed time since the last chemical purification of the material are presented and discussed. Completely separated uranium materials of known production date were distributed among the laboratories, and the samples were dated according to routine laboratory procedures by the measurement of the ²²⁰Th/²³⁴U ratio. The measurement results were in good agreement with the known production date showing that the concept for preparing uranium age dating reference material based on complete separation is valid. Detailed knowledge of the laboratory proceduresmore » used for uranium age dating allows the identification of possible improvements in the current protocols and the development of improved practice in the future. The availability of age dating reference materials as well as the evolvement of the age dating best-practice protocol will increase the relevance and applicability of age dating as part of the tool-kit available for nuclear forensic investigations.« less

  1. Dipole anisotropy of galaxy distribution: Does the CMB rest frame exist in the local universe?

    SciTech Connect (OSTI)

    Itoh, Yousuke; Yahata, Kazuhiro; Takada, Masahiro

    2010-08-15

    The peculiar motion of the Earth causes a dipole anisotropy modulation in the distant galaxy distribution due to the aberration effect. However, the amplitude and angular direction of the effect is not necessarily the same as those of the cosmic microwave background (CMB) dipole anisotropy due to the growth of cosmic structures. In other words exploring the aberration effect may give us a clue to the horizon-scale physics perhaps related to the cosmic acceleration. In this paper we develop a method to explore the dipole angular modulation from the pixelized galaxy data on the sky, properly taking into account the covariances due to the shot noise and the intrinsic galaxy clustering contamination as well as the partial sky coverage. We applied the method to the galaxy catalogs constructed from the Sloan Digital Sky Survey Data Release 6 data. After constructing the four galaxy catalogs that are different in the ranges of magnitudes and photometric redshifts to study possible systematics, we found that the most robust sample against systematics indicates no dipole anisotropy in the galaxy distribution. This finding is consistent with the expectation from the concordance {Lambda}-dominated cold dark matter model. Finally, we argue that an almost full-sky galaxy survey such as Large Synoptic Survey Telescope may allow for a significant detection of the aberration effect of the CMB dipole having the precision of constraining the angular direction to {approx}20 deg in radius. Assuming a hypothetical Large Synoptic Survey Telescope galaxy survey, we find that this method can confirm or reject the result implied from a stacked analysis of the kinetic Sunyaev-Zel'dovich effect of X-ray luminous clusters in Kashlinsky et al. (2008, 2009) if the implied cosmic bulk flow is not extended out to the horizon.

  2. Accelerating Offshore Wind Development | Department of Energy

    Energy Savers [EERE]

    Accelerating Innovation: We Do It Together Accelerating Innovation: We Do It Together January 22, 2015 - 2:06pm Addthis January 22, 2015 The debut of a 3D printed car, an EV version of the 50th anniversary Shelby Cobra, this week at the Detroit Auto Show is a big win for manufacturing innovation. Accelerating innovation is about meeting big technical challenges and addressing the challenge in a short time frame. Developing new manufacturing technology to design, print, construct and display the

  3. EV Everywhere Framing Workshop

    Broader source: Energy.gov (indexed) [DOE]

    Standards 15 20 25 30 35 40 new combined standard 35.5 mpg by 2016 Projected to reduce oil consumption by about 1.8 billion barrels over the lifetime of vehicles sold in next 5...

  4. Ultra-scale vehicle tracking in low spatial-resolution and low frame-rate overhead video

    SciTech Connect (OSTI)

    Carrano, C J

    2009-05-20

    Overhead persistent surveillance systems are becoming more capable at acquiring wide-field image sequences for long time-spans. The need to exploit this data is becoming ever greater. The ability to track a single vehicle of interest or to track all the observable vehicles, which may number in the thousands, over large, cluttered regions while they persist in the imagery either in real-time or quickly on-demand is very desirable. With this ability we can begin to answer a number of interesting questions such as, what are normal traffic patterns in a particular region or where did that truck come from? There are many challenges associated with processing this type of data, some of which we will address in the paper. Wide-field image sequences are very large with many thousands of pixels on a side and are characterized by lower resolutions (e.g. worse than 0.5 meters/pixel) and lower frame rates (e.g. a few Hz or less). The objects in the scenery can vary in size, density, and contrast with respect to the background. At the same time the background scenery provides a number of clutter sources both man-made and natural. We describe our current implementation of an ultrascale capable multiple-vehicle tracking algorithm for overhead persistent surveillance imagery as well as discuss the tracking and timing performance of the currently implemented algorithm which is aimed at utilizing grayscale electrooptical image sequences alone for the track segment generation.

  5. Manager Helps Washington County Develop Energy Efficiency Projects |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Manager Helps Washington County Develop Energy Efficiency Projects Manager Helps Washington County Develop Energy Efficiency Projects August 11, 2010 - 1:01pm Addthis An Energy Department grant funded Autumn Salamack's new job as resource conservation manager for Kitsap County, Washington, and the energy efficient windows framed behind her. | Photo courtesy of Kitsap County, WA | An Energy Department grant funded Autumn Salamack's new job as resource conservation manager

  6. NREL: Process Development and Integration Laboratory - Silicon Cluster Tool

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Capabilities Silicon Cluster Tool Capabilities Photo of a cylindrical metal chamber surrounded by numerous other smaller cylindrical or rectangular chambers. Each tool has several flanges and is typically held within a metal frame or rack. A computer is on a table in front of a cabinet of electronic equipment. Silicon cluster tool in the Process Development and Integration Laboratory. The Silicon cluster tool within the Process Development and Integration Laboratory is a 10-port cluster tool

  7. Environmental assessment operation of the HB-Line facility and frame waste recovery process for production of Pu-238 oxide at the Savannah River Site

    SciTech Connect (OSTI)

    1995-04-01

    The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0948, addressing future operations of the HB-Line facility and the Frame Waste Recovery process at the Savannah River Site (SRS), near Aiken, South Carolina. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, DOE has concluded that, the preparation of an environmental impact statement is not required, and is issuing this Finding of No Significant Impact.

  8. High resolution telescope including an array of elemental telescopes aligned along a common axis and supported on a space frame with a pivot at its geometric center

    DOE Patents [OSTI]

    Norbert, Massie A.; Yale, Oster

    1992-01-01

    A large effective-aperture, low-cost optical telescope with diffraction-limited resolution enables ground-based observation of near-earth space objects. The telescope has a non-redundant, thinned-aperture array in a center-mount, single-structure space frame. It employes speckle interferometric imaging to achieve diffraction-limited resolution. The signal-to-noise ratio problem is mitigated by moving the wavelength of operation to the near-IR, and the image is sensed by a Silicon CCD. The steerable, single-structure array presents a constant pupil. The center-mount, radar-like mount enables low-earth orbit space objects to be tracked as well as increases stiffness of the space frame. In the preferred embodiment, the array has elemental telescopes with subaperture of 2.1 m in a circle-of-nine configuration. The telescope array has an effective aperture of 12 m which provides a diffraction-limited resolution of 0.02 arc seconds. Pathlength matching of the telescope array is maintained by a electro-optical system employing laser metrology. Speckle imaging relaxes pathlength matching tolerance by one order of magnitude as compared to phased arrays. Many features of the telescope contribute to substantial reduction in costs. These include eliminating the conventional protective dome and reducing on-site construction activities. The cost of the telescope scales with the first power of the aperture rather than its third power as in conventional telescopes.

  9. High resolution telescope including an array of elemental telescopes aligned along a common axis and supported on a space frame with a pivot at its geometric center

    DOE Patents [OSTI]

    Norbert, M.A.; Yale, O.

    1992-04-28

    A large effective-aperture, low-cost optical telescope with diffraction-limited resolution enables ground-based observation of near-earth space objects. The telescope has a non-redundant, thinned-aperture array in a center-mount, single-structure space frame. It employes speckle interferometric imaging to achieve diffraction-limited resolution. The signal-to-noise ratio problem is mitigated by moving the wavelength of operation to the near-IR, and the image is sensed by a Silicon CCD. The steerable, single-structure array presents a constant pupil. The center-mount, radar-like mount enables low-earth orbit space objects to be tracked as well as increases stiffness of the space frame. In the preferred embodiment, the array has elemental telescopes with subaperture of 2.1 m in a circle-of-nine configuration. The telescope array has an effective aperture of 12 m which provides a diffraction-limited resolution of 0.02 arc seconds. Pathlength matching of the telescope array is maintained by a electro-optical system employing laser metrology. Speckle imaging relaxes pathlength matching tolerance by one order of magnitude as compared to phased arrays. Many features of the telescope contribute to substantial reduction in costs. These include eliminating the conventional protective dome and reducing on-site construction activities. The cost of the telescope scales with the first power of the aperture rather than its third power as in conventional telescopes. 15 figs.

  10. Economic Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Development Economic Development Los Alamos is committed to investing and partnering in economic development initiatives and programs that have a positive impact to stimulate business growth that creates jobs and strengthens communities in Northern New Mexico. September 20, 2013 LANS Venture Acceleration Fund (VAF) award enabled Ideum to develop motion recognition software for international release. Jim Spadaccini (R) has tapped into the Lab's economic development programs: VAF, NMSBA,

  11. Role of nuclear dynamics in the Asymmetric molecular-frame photoelectron angular distributions for C 1s photoejection from CO{sub 2}

    SciTech Connect (OSTI)

    Miyabe, Shungo; Haxton, Dan; Rescigno, Tom; McCurdy, Bill

    2010-11-30

    We report the results of semiclassical calculations of the asymmetric molecular-frame photoelectron angular distributions for C 1s ionization of CO{sub 2} measured with respect to the CO{sup +} and O{sup +} ions produced by subsequent Auger decay, and show how the decay event can be used to probe ultrafast molecular dynamics of the transient cation. The fixed-nuclei photoionization amplitudes were constructed using variationally obtained electron-molecular ion scattering wave functions. The amplitudes are then used in a semiclassical manner to investigate their dependence on the nuclear dynamics of the cation. The method introduced here can be used to study other core-level ionization events.

  12. Electron-impact excitation of Fe{sup 2+}: A comparison of intermediate coupling frame transformation, Breit-Pauli and Dirac R-matrix calculations

    SciTech Connect (OSTI)

    Badnell, N. R.; Ballance, C. P.

    2014-04-20

    Modeling the spectral emission of low-charge iron group ions enables the diagnostic determination of the local physical conditions of many cool plasma environments such as those found in H II regions, planetary nebulae, active galactic nuclei, etc. Electron-impact excitation drives the population of the emitting levels and, hence, their emissivities. By carrying-out Breit-Pauli and intermediate coupling frame transformation (ICFT) R-matrix calculations for the electron-impact excitation of Fe{sup 2+}, which both use the exact same atomic structure and the same close-coupling expansion, we demonstrate the validity of the application of the powerful ICFT method to low-charge iron group ions. This is in contradiction to the finding of Bautista et al., who carried-out ICFT and Dirac R-matrix calculations for the same ion. We discuss possible reasons.

  13. sustainable development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    sustainable development - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us ... Hydrogen Infrastructure Hydrogen Production Market Transformation Fuel Cells ...

  14. Side-by-side evaluation of a stressed-skin insulated-core panel house and a conventional stud-frame house. Final report

    SciTech Connect (OSTI)

    Rudd, A.; Chandra, S.

    1994-01-14

    Side-by-side energy testing and monitoring was conducted on two houses in Louisville, KY between January--March 1993. Both houses were identical except that one house was constructed with conventional US 2 by 4 studs and a truss roof while the other house was constructed with stress-skin insulated core panels for the walls and second floor ceiling. Air-tightness testing included fan pressurization by blower door, hour long tracer tests using sulphur hexafluoride, and two-week long time-averaged tests using perfluorocarbon tracers. An average of all the air-tightness test results showed the SSIC panel house to have 22 percent less air infiltration than the frame house. Air-tightness testing resulted in a recommendation that both houses have a fresh air ventilation system installed to provide 0.35 air changes per hour continuously. Thermal insulation quality testing was by infrared imaging. Pressure differential testing resulted in recommendations to use sealed combustion appliances, and to allow for more return air flow from closed rooms. This can be accomplished by separate return ducts or transfer ducts which simply connect closed rooms to the main body with a short duct. The SSIC house UA was lower in both cases. By measurement, co-heating tests showed the SSIC panel house total UA to be 12 percent lower than the frame house. Short-term energy monitoring was also conducted for the two houses. A 17 day period of electric heating and a 14 day period of gas furnace heating was evaluated. Monitoring results showed energy savings for the panel house to be 12 percent during electric heating and 15 percent during gas heating. A comparison of the two monitoring periods showed that the lumped efficiency of the gas furnace and air distribution system for both houses was close to 80 percent. Simple regression models using Typical Meteorological Year weather data gave a preliminary prediction of seasonal energy savings between 14 and 20 percent.

  15. C:\\Forms\\DOE F 3305.14f.cdr

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    CONTENT DESCRIPTION: Focuses on involvement in the process and systems used to monitor program develop- ment, policy implementation, and program effectiveness. Also includes other ...

  16. May 2002

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    collateral damage that destroys normal lung tissue followed by scar tissue develop- ment. ... Typical components of such a plan include engineering controls (physically separat- ing ...

  17. ADVANCED SORBENT DEVELOPMENT PROGRAM; DEVELOPMENT OF SORBENTS FOR MOVING-BED AND FLUIDIZED-BED APPLICATIONS

    SciTech Connect (OSTI)

    R.E. AYALA; V.S. VENKATARAMANI

    1998-09-30

    The integrated gasification combined cycle (IGCC) power system using high-temperature coal gas cleanup is one of the most promising advanced technologies for the production of electric power from coal in an environmentally acceptable manner. Unlike conventional low-temperature cleanup systems that require costly heat exchangers, high-temperature coal gas cleanup systems can be operated near 482-538 C (900-1000F) or higher, conditions that are a closer match with the gasifier and turbine components in the IGCC system, thus resulting is a more efficient overall system. GE is developing a moving-bed, high-temperature desulfurization system for the IGCC power cycle in which zinc-based regenerable sorbents are currently being used as desulfurization sorbents. Zinc titanate and other proprietary zinc-based oxides are being considered as sorbents for use in the Clean Coal Technology Demonstration Program at Tampa Electric Co.?s (TECo) Polk Power Station. Under cold startup conditions at TECo, desulfurization and regeneration may be carried out at temperatures as low as 343 C (650 F), hence a versatile sorbent is desirable to perform over this wide temperature range. A key to success in the development of high-temperature desulfurization systems is the matching of sorbent properties for the selected process operating conditions, namely, sustainable desulfurization kinetics, high sulfur capacity, and mechanical durability over multiple cycles. Additionally, the sulfur species produced during regeneration of the sorbent must be in a form compatible with sulfur recovery systems, such as sulfuric acid or elemental sulfur processes. The overall objective of this program is to develop regenerable sorbents for hydrogen sulfide removal from coal-derived fuel gases in the temperature range 343-538 C (650-1000 F). Two categories of reactor configurations are being considered: moving-bed reactors and fluidized-bed (bubbling and circulating) reactors. In addition, a cost assessment and a market plan for large-scale fabrication of sorbents were developed. As an optional task, long-term bench-scale tests of the best moving-bed sorbents were conducted. Starting from thermodynamic calculations, several metal oxides were identified for potential use as hot gas cleanup sorbents using constructed phase stability diagrams and laboratory screening of various mixed-metal oxide formulations. Modified zinc titanates and other proprietary metal oxide formulations were evaluated at the bench scale and many of them found to be acceptable for operation in the target desulfurization temperature range of 370 C (700 F) to 538 C (1000 F) and regeneration tempera-tures up to 760 C (1400 F). Further work is still needed to reduce the batch-to-batch repeatability in the fabrication of modified zinc titanates for larger scale applications. The information presented in this Volume 1 report contains the results of moving-bed sorbent develop-ment at General Electric?s Corporate Research and Development (GE-CRD). A separate Volume 2 report contains the results of the subcontract on fluidized-bed sorbent development at the Institute of Gas Technology (IGT).

  18. Program Development

    SciTech Connect (OSTI)

    Atencio, Julian J.

    2014-05-01

    This presentation covers how to go about developing a human reliability program. In particular, it touches on conceptual thinking, raising awareness in an organization, the actions that go into developing a plan. It emphasizes evaluating all positions, eliminating positions from the pool due to mitigating factors, and keeping the process transparent. It lists components of the process and objectives in process development. It also touches on the role of leadership and the necessity for audit.

  19. EPA, NREL Partner to Develop Renewable Energy on Potentially Contaminated

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EPA Redesigns Conversion Certification Policies At a recent meeting held in Washington, DC, officials from the U.S. Environmental Protection Agency (EPA) opened dialogue about proposed changes to its emission certification policies that affect alternative fuel vehicles (AFVs). "We are trying to accommo- date the Energy Policy Act (EPAct) and Executive Order requirements while trying to change enforce- ment policies and guidance with respect to conversions," said Rich Ackerman of EPA's

  20. PHYSICAL PROPERTIES OF SPECTROSCOPICALLY CONFIRMED GALAXIES AT z {>=} 6. I. BASIC CHARACTERISTICS OF THE REST-FRAME UV CONTINUUM AND Ly{alpha} EMISSION

    SciTech Connect (OSTI)

    Jiang Linhua; Mechtley, Matthew; Cohen, Seth H.; Windhorst, Rogier A.; Egami, Eiichi; Fan Xiaohui; Dave, Romeel; Finlator, Kristian; Kashikawa, Nobunari; Ouchi, Masami; Shimasaku, Kazuhiro

    2013-08-01

    We present deep Hubble Space Telescope near-IR and Spitzer mid-IR observations of a large sample of spectroscopically confirmed galaxies at z {>=} 6. The sample consists of 51 Ly{alpha} emitters (LAEs) at z {approx_equal} 5.7, 6.5, and 7.0, and 16 Lyman break galaxies (LBGs) at 5.9 {<=} z {<=} 6.5. The near-IR images were mostly obtained with WFC3 in the F125W and F160W bands, and the mid-IR images were obtained with IRAC in the 3.6 {mu}m and 4.5 {mu}m bands. Our galaxies also have deep optical imaging data from Subaru Suprime-Cam. We utilize the multi-band data and secure redshifts to derive their rest-frame UV properties. These galaxies have steep UV-continuum slopes roughly between {beta} {approx_equal} -1.5 and -3.5, with an average value of {beta} {approx_equal} -2.3, slightly steeper than the slopes of LBGs in previous studies. The slope shows little dependence on UV-continuum luminosity except for a few of the brightest galaxies. We find a statistically significant excess of galaxies with slopes around {beta} {approx_equal} -3, suggesting the existence of very young stellar populations with extremely low metallicity and dust content. Our galaxies have moderately strong rest-frame Ly{alpha} equivalent width (EW) in a range of {approx}10 to {approx}200 A. The star formation rates are also moderate, from a few to a few tens of solar masses per year. The LAEs and LBGs in this sample share many common properties, implying that LAEs represent a subset of LBGs with strong Ly{alpha} emission. Finally, the comparison of the UV luminosity functions between LAEs and LBGs suggests that there exists a substantial population of faint galaxies with weak Ly{alpha} emission (EW < 20 A) that could be the dominant contribution to the total ionizing flux at z {>=} 6.

  1. Framing the Energy Technology Menu

    U.S. Energy Information Administration (EIA) Indexed Site

    years... 20 years Energy System Characteristics ... Environmentclimate change: "de-carbonize" by mid- ... to DOE's leadership- class and advanced architecture ...

  2. Framing the Energy Technology Menu

    U.S. Energy Information Administration (EIA) Indexed Site

    ... cycle (IGCC) l Advanced concepts, e.g. chemical looping l Optimized capture plant always ... of radiation-tolerant materials and chemical separation processes for fission ...

  3. 70002-MAPPER FAB FRAME ASSY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    19 27.99 42.62 9 138.00 132.00 166.75 211.00 1 5 7 6 4 3 2 8 NOTES: 1) ALL WELDS ARE FILLET, NOT SHOWN 2) ALL WELDS CONTINUOUS 3) PAINT ALL UNMACHINED SURFACES BLUE ENAMEL Parts...

  4. Software Developers

    Broader source: Energy.gov [DOE]

    Because SEED will provide a common, open-source data framework, software developers will be able to write applications that access the data in a consistent way (with proper permissions), or build functionalities onto the SEED platform in a replicable way.

  5. HerMES: The rest-frame UV emission and a lensing model for the z = 6.34 luminous dusty starburst galaxy HFLS3

    SciTech Connect (OSTI)

    Cooray, Asantha; Calanog, Jae; Casey, C. M.; Ma, Brian; Osage, W. A.; Wardlow, Julie L.; Bock, J.; Bridge, C.; Burgarella, D.; Bussmann, R. S.; Clements, D.; Conley, A.; Farrah, D.; Fu, H.; Gavazzi, R.; Ivison, R. J.; La Porte, N.; Lo Faro, B.; Magdis, G.; Oliver, S. J.; and others

    2014-07-20

    We discuss the rest-frame ultraviolet emission from the starbursting galaxy HFLS3 at a redshift of 6.34. The galaxy was discovered in Herschel/SPIRE data due to its red color in the submillimeter wavelengths from 250 to 500 ?m. Keck/NIRC2 K{sub s}-band adaptive optics imaging data showed two potential near-IR counterparts near HFLS3. Previously, the northern galaxy was taken to be in the foreground at z = 2.1, while the southern galaxy was assumed to be HFLS3's near-IR counterpart. The recently acquired Hubble/WFC3 and Advanced Camera for Surveys (ACS) imaging data show conclusively that both optically bright galaxies are in the foreground at z < 6. A new lensing model based on the Hubble imaging data and the millimeter-wave continuum emission yields a magnification factor of 2.2 0.3, with a 95% confidence upper limit on the magnification of 3.5. When corrected for lensing, the instantaneous star formation rate is 1320 M{sub ?} yr{sup 1}, with the 95% confidence lower limit around 830 M{sub ?} yr{sup 1}. The dust and stellar masses of HFLS3 from the same spectral energy distribution (SED) models are at the level of 3 10{sup 8} M{sub ?} and ?5 10{sup 10} M{sub ?}, respectively, with large systematic uncertainties on assumptions related to the SED model. With Hubble/WFC3 images, we also find diffuse near-IR emission about 0.5 arcsec (?3 kpc) to the southwest of HFLS3 that remains undetected in the ACS imaging data. The emission has a photometric redshift consistent with either z ? 6 or a dusty galaxy template at z ? 2.

  6. RELATIVISTIC JETS IN THE RADIO REFERENCE FRAME IMAGE DATABASE. II. BLAZAR JET ACCELERATIONS FROM THE FIRST 10 YEARS OF DATA (1994-2003)

    SciTech Connect (OSTI)

    Piner, B. G.; Marvin, C. J.; Arenson, J. G.; Pushkarev, A. B.; Fey, A. L.

    2012-10-20

    We analyze blazar jet apparent speeds and accelerations from the RDV series of astrometric and geodetic very long baseline interferometry (VLBI) experiments. From these experiments, we have produced and analyzed 2753 global VLBI images of 68 sources at 8 GHz with a median beam size of 0.9 milliarcseconds (mas) and a median of 43 epochs per source. From this sample, we analyze the motions of 225 jet components in 66 sources. The distribution of the fastest measured apparent speed in each source has a median of 8.3c and a maximum of 44c. Sources in the 2FGL Fermi LAT catalog display higher apparent speeds than those that have not been detected. On average, components farther from the core in a given source have significantly higher apparent speeds than components closer to the core; for example, for a typical source, components at {approx}3 mas from the core ({approx}15 pc projected at z {approx} 0.5) have apparent speeds about 50% higher than those of components at {approx}1 mas from the core ({approx}5 pc projected at z {approx} 0.5). We measure accelerations of components in orthogonal directions parallel and perpendicular to their average velocity vector. Parallel accelerations have significantly larger magnitudes than perpendicular accelerations, implying that observed accelerations are predominantly due to changes in the Lorentz factor (bulk or pattern) rather than projection effects from jet bending. Positive parallel accelerations are significantly more common than negative ones, so the Lorentz factor (bulk or pattern) tends to increase on the scales observed here. Observed parallel accelerations correspond to modest source frame increases in the bulk or pattern Lorentz factor.

  7. Technology Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Development - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear

  8. Nozzle development

    SciTech Connect (OSTI)

    Dodge, F.T.; Dodge, L.G.; Johnson, J.E.

    1989-06-01

    The objective of this program has been the development of experimental techniques and data processing procedures to allow for the characterization of multi-phase fuel nozzles using laboratory tests. Test results were to be used to produce a single value coefficient-of-performance that would predict the performance of the fuel nozzles independent of system application. Several different types of fuel nozzles capable of handling multi-phase fuels have been characterized for: (a) fuel flow rate versus delivery pressure, (b) fuel-air ratio throughout the fuel spray or plume and the effective cone angle of the injector, and (c) fuel drop- or particle-size distribution as a function of fluid properties. Fuel nozzles which have been characterized on both single-phase liquids and multi-phase liquid-solid slurries include a variable-film-thickness nozzle, a commercial coal-water slurry (CWS) nozzle, and four diesel injectors of different geometries (tested on single-phase fluids only). Multi-phase mixtures includes CWS with various coal loadings, surfactant concentrations, and stabilizer concentrations, as well as glass-bead water slurries with stabilizing additives. Single-phase fluids included glycerol-water mixtures to vary the viscosity over a range of 1 to 1500 cP, and alcohol-water mixtures to vary the surface tension from about 22 to 73 dyne/cm. In addition, tests were performed to characterize straight-tube gas-solid nozzles using two differences size distributions of glass beads in air. Standardized procedures have been developed for processing measurements of spray drop-size characteristics and the overall cross-section average drop or particle size. 43 refs., 60 figs., 7 tabs.

  9. Advanced Hydrogen Turbine Development

    SciTech Connect (OSTI)

    Joesph Fadok

    2008-01-01

    Siemens has developed a roadmap to achieve the DOE goals for efficiency, cost reduction, and emissions through innovative approaches and novel technologies which build upon worldwide IGCC operational experience, platform technology, and extensive experience in G-class operating conditions. In Phase 1, the technologies and concepts necessary to achieve the program goals were identified for the gas turbine components and supporting technology areas and testing plans were developed to mitigate identified risks. Multiple studies were conducted to evaluate the impact in plant performance of different gas turbine and plant technologies. 2015 gas turbine technologies showed a significant improvement in IGCC plant efficiency, however, a severe performance penalty was calculated for high carbon capture cases. Thermodynamic calculations showed that the DOE 2010 and 2015 efficiency targets can be met with a two step approach. A risk management process was instituted in Phase 1 to identify risk and develop mitigation plans. For the risks identified, testing and development programs are in place and the risks will be revisited periodically to determine if changes to the plan are necessary. A compressor performance prediction has shown that the design of the compressor for the engine can be achieved with additional stages added to the rear of the compressor. Tip clearance effects were studied as well as a range of flow and pressure ratios to evaluate the impacts to both performance and stability. Considerable data was obtained on the four candidate combustion systems: diffusion, catalytic, premix, and distributed combustion. Based on the results of Phase 1, the premixed combustion system and the distributed combustion system were chosen as having the most potential and will be the focus of Phase 2 of the program. Significant progress was also made in obtaining combustion kinetics data for high hydrogen fuels. The Phase 1 turbine studies indicate initial feasibility of the advanced hydrogen turbine that meets the aggressive targets set forth for the advanced hydrogen turbine, including increased rotor inlet temperature (RIT), lower total cooling and leakage air (TCLA) flow, higher pressure ratio, and higher mass flow through the turbine compared to the baseline. Maintaining efficiency with high mass flow Syngas combustion is achieved using a large high AN2 blade 4, which has been identified as a significant advancement beyond the current state-of-the-art. Preliminary results showed feasibility of a rotor system capable of increased power output and operating conditions above the baseline. In addition, several concepts were developed for casing components to address higher operating conditions. Rare earth modified bond coat for the purpose of reducing oxidation and TBC spallation demonstrated an increase in TBC spallation life of almost 40%. The results from Phase 1 identified two TBC compositions which satisfy the thermal conductivity requirements and have demonstrated phase stability up to temperatures of 1850 C. The potential to join alloys using a bonding process has been demonstrated and initial HVOF spray deposition trials were promising. The qualitative ranking of alloys and coatings in environmental conditions was also performed using isothermal tests where significant variations in alloy degradation were observed as a function of gas composition. Initial basic system configuration schematics and working system descriptions have been produced to define key boundary data and support estimation of costs. Review of existing materials in use for hydrogen transportation show benefits or tradeoffs for materials that could be used in this type of applications. Hydrogen safety will become a larger risk than when using natural gas fuel as the work done to date in other areas has shown direct implications for this type of use. Studies were conducted which showed reduced CO{sub 2} and NOx emissions with increased plant efficiency. An approach to maximize plant output is needed in order to address the DOE turbine goal for 20-30% reduction of combined cycle cost from the baseline. A customer advisory board was instituted during Phase 1 to obtain important feedback regarding the future direction of the project. he technologies being developed for the Hydrogen Turbine will also be utilized, as appropriate, in the 2010 time frame engine and the FutureGen Plant. These new technologies and concepts also have the potential to accelerate commercialization of advanced coal-based IGCC plants in the U. S. and around the world, thereby reducing emissions, water use, solid waste production and dependence on scarce, expensive and insecure foreign energy supplies. Technology developments accomplished in Phase 1 provide a solid foundation for ensuring successful completion in Phase 2 and providing that the challenging program goals will be achieved.

  10. PHYSICAL PROPERTIES OF SPECTROSCOPICALLY CONFIRMED GALAXIES AT z {>=} 6. II. MORPHOLOGY OF THE REST-FRAME UV CONTINUUM AND Ly{alpha} EMISSION

    SciTech Connect (OSTI)

    Jiang Linhua; Windhorst, Rogier A.; Cohen, Seth H.; Mechtley, Matthew; Egami, Eiichi; Fan Xiaohui; Dave, Romeel; Finlator, Kristian; Kashikawa, Nobunari; Ouchi, Masami; Shimasaku, Kazuhiro

    2013-08-20

    We present a detailed structural and morphological study of a large sample of spectroscopically confirmed galaxies at z {>=} 6 using deep Hubble Space Telescope (HST) near-IR broad-band images and Subaru Telescope optical narrow-band images. The galaxy sample consists of 51 Ly{alpha} emitters (LAEs) at z {approx_equal} 5.7, 6.5, and 7.0, and 16 Lyman break galaxies (LBGs) at 5.9 {<=} z {<=} 6.5. These galaxies exhibit a wide range of rest-frame UV continuum morphology in the HST images, from compact features to multiple component systems. The fraction of merging/interacting galaxies reaches 40%-50% at the brightest end of M{sub 1500} {<=} -20.5 mag. The intrinsic half-light radii r{sub hl,in}, after correcting for point-spread function (PSF) broadening, are roughly between r{sub hl,in} {approx_equal} 0.''05 (0.3 kpc) and 0.''3 (1.7 kpc) at M{sub 1500} {<=} -19.5 mag. The median r{sub hl,in} value is 0.''16 ({approx}0.9 kpc). This is consistent with the sizes of bright LAEs and LBGs at z {>=} 6 found in previous studies. In addition, more luminous galaxies tend to be larger and exhibit a weak size-luminosity relation, r{sub hl,in}{proportional_to}L {sup 0.14} at M{sub 1500} {<=} -19.5 mag. The slope of 0.14 is significantly flatter than those in fainter LBG samples. We discuss the morphology of z {>=} 6 galaxies with nonparametric methods, including the concentration, asymmetry, and smoothness system and the Gini and M{sub 20} parameters, and demonstrate their validity through simulations. We search for extended Ly{alpha} emission halos around LAEs at z {approx_equal} 5.7 and 6.5 by stacking a number of narrow-band images. We do not find evidence of extended Ly{alpha} halos predicted by cosmological simulations. Such halos, if they exist, could be weaker than predicted. Finally, we investigate positional misalignment between the UV continuum and Ly{alpha} emissions in LAEs. While the two positions are generally consistent, several merging galaxies show significant positional differences. This is likely caused by a disturbed interstellar medium distribution due to merging activity.

  11. GAMMA-RAY BURST AFTERGLOW LIGHT CURVES FROM A LORENTZ-BOOSTED SIMULATION FRAME AND THE SHAPE OF THE JET BREAK

    SciTech Connect (OSTI)

    Van Eerten, Hendrik; MacFadyen, Andrew

    2013-04-20

    The early stages of decelerating gamma-ray burst (GRB) afterglow jets have been notoriously difficult to resolve numerically using two-dimensional hydrodynamical simulations even at very high resolution, due to the extreme thinness of the blast wave and high outflow Lorentz factors. However, these resolution issues can be avoided by performing the simulations in a boosted frame, which makes it possible to calculate afterglow light curves from numerically computed flows in sufficient detail to accurately quantify the shape of the jet break and the post-break steepening of the light curve. Here, we study afterglow jet breaks for jets with opening angles of 0.05, 0.1, and 0.2 radians decelerating in a surrounding medium of constant density, observed at various angles ranging from on-axis to the edge of the jet. A single set of scale-invariant functions describing the time evolution of afterglow synchrotron spectral break frequencies and peak flux, depending only on jet opening angle and observer angle, are all that is needed to reconstruct light curves for arbitrary explosion energy, circumburst density and synchrotron particle distribution power law slope p. These functions are presented in the paper. Their time evolutions change directly following the jet break, although an earlier reported temporary post-break steepening of the cooling break is found to have been resolution-induced. We compare synthetic light curves to fit functions using sharp power law breaks as well as smooth power law transitions. We confirm our earlier finding that the measured jet break time is very sensitive to the angle of the observer and can be postponed significantly. We find that the difference in temporal indices across the jet break is larger than theoretically anticipated and is about -(0.5 + 0.5p) below the cooling break and about -(0.25 + 0.5p) above the cooling break, both leading to post-break slopes of roughly about 0.25 - 1.3p, although different observer angles, jet opening angles and heuristic descriptions of the break introduce a wide range of temporal indices. Nevertheless, the post-break slope from our constant density interstellar medium simulations is sufficiently steep to be hard to reconcile with post-break slopes measured for the Swift sample, suggesting that Swift GRBs mostly do not explode in a homogeneous medium or that the jet breaks are hidden from view by additional physics such as prolonged energy injection or viewing angle effects. A comparison between different smooth power law fit functions shows that although smooth power law transitions of the type introduced by Harrison et al. often provide better fits, smooth power law transitions of the type introduced by Beuermann et al. or even sharp power law fits are easier to interpret in terms of the underlying model. Light curves and spectral break and peak flux evolution functions will be made publicly available online at http://cosmo.nyu.edu/afterglowlibrary.

  12. Phase 1 Development Report for the SESSA Toolkit.

    SciTech Connect (OSTI)

    Knowlton, Robert G.; Melton, Brad J; Anderson, Robert J.

    2014-09-01

    The Site Exploitation System for Situational Awareness ( SESSA ) tool kit , developed by Sandia National Laboratories (SNL) , is a comprehensive de cision support system for crime scene data acquisition and Sensitive Site Exploitation (SSE). SESSA is an outgrowth of another SNL developed decision support system , the Building R estoration Operations Optimization Model (BROOM), a hardware/software solution for data acquisition, data management, and data analysis. SESSA was designed to meet forensic crime scene needs as defined by the DoD's Military Criminal Investigation Organiza tion (MCIO) . SESSA is a very comprehensive toolki t with a considerable amount of database information managed through a Microsoft SQL (Structured Query Language) database engine, a Geographical Information System (GIS) engine that provides comprehensive m apping capabilities, as well as a an intuitive Graphical User Interface (GUI) . An electronic sketch pad module is included. The system also has the ability to efficiently generate necessary forms for forensic crime scene investigations (e.g., evidence submittal, laboratory requests, and scene notes). SESSA allows the user to capture photos on site, and can read and generate ba rcode labels that limit transcription errors. SESSA runs on PC computers running Windows 7, but is optimized for touch - screen tablet computers running Windows for ease of use at crime scenes and on SSE deployments. A prototype system for 3 - dimensional (3 D) mapping and measur e ments was also developed to complement the SESSA software. The mapping system employs a visual/ depth sensor that captures data to create 3D visualizations of an interior space and to make distance measurements with centimeter - level a ccuracy. Output of this 3D Model Builder module provides a virtual 3D %22walk - through%22 of a crime scene. The 3D mapping system is much less expensive and easier to use than competitive systems. This document covers the basic installation and operation of th e SESSA tool kit in order to give the user enough information to start using the tool kit . SESSA is currently a prototype system and this documentation covers the initial release of the tool kit . Funding for SESSA was provided by the Department of Defense (D oD), Assistant Secretary of Defense for Research and Engineering (ASD(R&E)) Rapid Fielding (RF) organization. The project was managed by the Defense Forensic Science Center (DFSC) , formerly known as the U.S. Army Criminal Investigation Laboratory (USACIL) . ACKNOWLEDGEMENTS The authors wish to acknowledge the funding support for the development of the Site Exploitation System for Situational Awareness (SESSA) toolkit from the Department of Defense (DoD), Assistant Secretary of Defense for Research and Engineering (ASD(R&E)) Rapid Fielding (RF) organization. The project was managed by the Defense Forensic Science Center (DFSC) , formerly known as the U.S. Army Criminal Investigation Laboratory (USACIL). Special thanks to Mr. Garold Warner, of DFSC, who served as the Project Manager. Individuals that worked on the design, functional attributes, algorithm development, system arc hitecture, and software programming include: Robert Knowlton, Brad Melton, Robert Anderson, and Wendy Amai.

  13. DOE Zero Energy Ready Home Case Study: StreetScape Development, LLC,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Libertyville, IL, Custom | Department of Energy StreetScape Development, LLC, Libertyville, IL, Custom DOE Zero Energy Ready Home Case Study: StreetScape Development, LLC, Libertyville, IL, Custom Case study of a DOE Zero Energy Ready Home in Libertyville, IL, that scored HERS 45 without PV. This 2,763-square-foot custom home has advanced framed walls with R-20 of open-cell spray foam, R-49 open-cell spray-foam sealed attic, an HRV, and a tankless water heater for hydro coil furnace with

  14. Progress report on a fully automatic Gas Tungsten Arc Welding (GTAW) system development

    SciTech Connect (OSTI)

    Daumeyer, G.J. III

    1994-12-01

    A plan to develop a fully automatic gas tungsten arc welding (GTAW) system that will utilize a vision-sensing computer (which will provide in-process feedback control) is presently in work. Evaluations of different technological aspects and system design requirements continue. This report summaries major activities in the plan`s successful progress. The technological feasibility of producing the fully automated GTAW system has been proven. The goal of this process development project is to provide a production-ready system within the shortest reasonable time frame.

  15. Instrument Development H. E. Revercomb, F. A. Best, R. G. Dedecker, T. P. Dirkx,

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    H. E. Revercomb, F. A. Best, R. G. Dedecker, T. P. Dirkx, R. A. Herbsleb, R. O. Knuteson, J. F. Short, and W. L. Smith University of Wisconsin -Madison Space Science and Engineering Center Madison, WI 53706 Ground-based Folurier Transform infrared (FTIR) instru- ments are being produced at the University of Wisconsin (UW) and the Unliversity of Denver (UD) for the Atmo- spheric Radiation Measurement (ARM) Program's Cloud and Radiation Te:stbed (CART) sites as part of a joint Instrument

  16. Bioenergy for Sustainable Development

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SUSTAINABLE DEVELOPMENT Overview * Energy poverty is widespread and prevents economic development * The international development community is beginning to act * Momentum is ...

  17. Chemical sensors technology development planning workshop

    SciTech Connect (OSTI)

    Bastiaans, G.J.; Haas, W.J. Jr.; Junk, G.A.

    1993-03-01

    The workshop participants were asked to: (1) Assess the current capabilities of chemical sensor technologies for addressing US Department of Energy (DOE) Environmental Restoration and Waste Management (EM) needs; (2) Estimate potential near term (one to two years) and intermediate term (three to five years) capabilities for addressing those needs; and (3) Generate a ranked list of specific recommendations on what research and development (R&D) should be funded to provide the necessary capabilities. The needs were described in terms of two pervasive EM problems, the in situ determination of chlorinated volatile organic compounds (VOCs), and selected metals in various matrices at DOE sites. The R&D recommendations were to be ranked according to the estimated likelihood that the product technology will be ready for application within the time frame it is needed and the estimated return on investment. The principal conclusions and recommendations of the workshop are as follows: Chemical sensors capable of in situ determinations can significantly reduce analytical costs; Chemical sensors have been developed for certain VOCs in gases and water but none are currently capable of in situ determination of VOCs in soils; The DOE need for in situ determination of metals in soils cannot be addressed with existing chemical sensors and the prospects for their availability in three to five years are uncertain; Adaptation, if necessary, and field application of laboratory analytical instruments and those few chemical sensors that are already in field testing is the best approach for the near term; The chemical sensor technology development plan should include balanced support for near- and intermediate-term efforts.

  18. FRAMES-2.0 Software System: Linking to the Groundwater Modeling System (GMS) RT3D and MT3DMS Models

    SciTech Connect (OSTI)

    Whelan, Gene; Castleton, Karl J.; Pelton, Mitch A.

    2007-08-08

    Linkages to the Groundwater Modeling System have been developed at Pacific Northwest National Laboratory to enable the Nuclear Regulatory Commission (NRC) to more realistically assess the risk to the public of radioactive contaminants at NRC-licensed sites. Common software tools presently in use are limited in that they cannot assess contaminant migration through complex natural environments. The purpose of this initiative is to provide NRC with a licensing safety-analysis tool with sufficient power, flexibility, and utility that it can serve as the primary software platform for analyzing the hazards associated with licensing actions at those complex sites at which the traditional tools are inappropriate. As a tool designed to realistically approximate prospective doses to the public, this initiative addresses NRCs safety-performance goal by confirming that licensing actions do not result in undue risk to the public.

  19. Prototype Development Capabilities of 3D Spatial Interactions and Failures During Scenario Simulation

    SciTech Connect (OSTI)

    Steven Prescott; Ramprasad Sampath; Curtis Smith; Tony Koonce

    2014-09-01

    Computers have been used for 3D modeling and simulation, but only recently have computational resources been able to give realistic results in a reasonable time frame for large complex models. This report addressed the methods, techniques, and resources used to develop a prototype for using 3D modeling and simulation engine to improve risk analysis and evaluate reactor structures and components for a given scenario. The simulations done for this evaluation were focused on external events, specifically tsunami floods, for a hypothetical nuclear power facility on a coastline.

  20. DOE Zero Energy Ready Home Case Study: Weiss Building & Development LLC.,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Custom Home, Downers Grove, IL | Department of Energy LLC., Custom Home, Downers Grove, IL DOE Zero Energy Ready Home Case Study: Weiss Building & Development LLC., Custom Home, Downers Grove, IL Case study of a DOE Zero Energy Ready Home in Downers Grove, IL, that scored HERS 35 without PV. This 3,600-square-foot custom home has advanced framed walls with R-23 dense-packed fiberglass plus R-13 rigid polyiso, a sealed attic with open-cell spray foam, a pier foundation, and 95% efficient

  1. Teacher Development Programs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Teacher Development Programs LLNL Teacher Development LLNL's Science Education Program provides professional development instruction to in-service and pre-service middle school, high school, and community college science teachers

  2. Development of a Fast Time-Resolved Aerosol Collector (Fast TRAC...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    map and times SEMEDX map and elemental analysis Xiao-Ying Yu, James Cowin PNNL Fast Framing * 240 framessec * 4 ms per frame * See 100 nm particles arriving New 100 nm...

  3. Development of a Fast Time-Resolved Aerosol Collector (Fast TRAC...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    map and times SEMEDX map and elemental analysis Xiao-Ying Yu & James Cowin PNNL Fast Framing * 240 framessec * 4 ms per frame * See 100 nm particles arriving New 100 nm...

  4. Clean Energy Development Fund

    Office of Energy Efficiency and Renewable Energy (EERE)

    Vermont's Clean Energy Development Fund (CEDF) was established in 2005 to promote the development and deployment of cost-effective and environmentally sustainable electric power and thermal...

  5. ORISE: Web Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Web Development As computer-based applications become increasingly popular for the delivery of health care training and information, the need for Web development in support of ...

  6. Understanding Energy Impacts of Oversized Air Conditioners (Fact Sheet), NREL Highlights, Research & Development, NREL (National Renewable Energy Laboratory)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    research reveals the effects of parasitic power losses on the energy consumption of oversized residential air conditioners. Retrofits of existing homes can be substantial invest- ments that reduce home energy use for years; there- fore, knowledge about the energy impacts of building systems is critical. In the case of air conditioners, conven- tional wisdom suggests that oversized cooling equipment leads to higher energy use because equipment cycling is inefficient. It also implies that there

  7. Geothermal development opportunities in developing countries

    SciTech Connect (OSTI)

    Kenkeremath, D.C.

    1989-11-16

    This report is the proceedings of the Seminar on geothermal development opportunities in developing countries, sponsored by the Geothermal Division of the US Department of Energy and presented by the National Geothermal Association. The overall objectives of the seminar are: (1) Provide sufficient information to the attendees to encourage their interest in undertaking more geothermal projects within selected developing countries, and (2) Demonstrate the technological leadership of US technology and the depth of US industry experience and capabilities to best perform on these projects.

  8. Options for developing countries in mining development

    SciTech Connect (OSTI)

    Walrond, G.W.; Kumar, R.

    1985-01-01

    This book is a study of the issues that developing countries face in planning and implementing mineral development, taking as case studies Botswana, Sierra Leone, Zambia, Tanzania, Malaysia, Papua New Guinea and the developed states of Quebec and Western Australia. The authors consider the major aspects of the matter including organization and administration; regulation; taxation and surplus distribution; the dynamics of such instruments as royalty, rent resource tax and capital allowances under various cost/price scenarios; and selected mining agreements and their key provisions. They stress throughout the need for foreign investment while maximizing the economic benefits reaped from exhaustible resources.

  9. SES CANDIDATE DEVELOPMENT PROGRAM

    Energy Savers [EERE]

    SENIOR EXECUTIVE SERVICE CANDIDATE DEVELOPMENT PROGRAM (SESCDP) DOE F 360.1 (11-03) Executive Development Plan (EDP) Name: Title: Organization: Office: RATIONALE FOR PLAN: APPROVALS: Candidate Signature: Date: Supervisor: Date: Mentor: Date: SES Candidate Development Program Manager: Date: DOE Executive Resources Board: Date: 1 U.S. DEPARTMENT OF ENERGY DOE F 360.1 (11-03) SENIOR EXECUTIVE SERVICE CANDIDATE DEVELOPMENT PROGRAM (SESCDP) Executive Development Plan (EDP) NAME OF SES CANDIDATE:

  10. Uncertainty quantification of cinematic imaging for development of predictive simulations of turbulent combustion.

    SciTech Connect (OSTI)

    Lawson, Matthew; Debusschere, Bert J.; Najm, Habib N.; Sargsyan, Khachik; Frank, Jonathan H.

    2010-09-01

    Recent advances in high frame rate complementary metal-oxide-semiconductor (CMOS) cameras coupled with high repetition rate lasers have enabled laser-based imaging measurements of the temporal evolution of turbulent reacting flows. This measurement capability provides new opportunities for understanding the dynamics of turbulence-chemistry interactions, which is necessary for developing predictive simulations of turbulent combustion. However, quantitative imaging measurements using high frame rate CMOS cameras require careful characterization of the their noise, non-linear response, and variations in this response from pixel to pixel. We develop a noise model and calibration tools to mitigate these problems and to enable quantitative use of CMOS cameras. We have demonstrated proof of principle for image de-noising using both wavelet methods and Bayesian inference. The results offer new approaches for quantitative interpretation of imaging measurements from noisy data acquired with non-linear detectors. These approaches are potentially useful in many areas of scientific research that rely on quantitative imaging measurements.

  11. Framing Sustainability in a Telecoupled World

    SciTech Connect (OSTI)

    Liu, Jianguo; Hull, Vanessa; Batistella, Mateus; Defries, Ruth; Dietz, Tom; Fu, Feng; Hertel, Thomas W.; Izaurralde, Roberto C.; Lambin, Eric F.; Li, Shuxin; Martinelli, Antonio Luiz; McConnell, William; Moran, Emilio; Naylor, Rosamond; Ouyang, Zhiyum; Polenske, Karen R.; Reenberg, Anette; de Miranda Rocha, Gilberto; Simmons, Cynthia S.; Verbug, Peter H.; Vitousek, Peter M.; Zhang, Fusuo; Zhu, Chunquan

    2013-06-17

    Interactions between distant places are increasingly widespread and influential, often leading to unexpected outcomes with profound implications for sustainability. Numerous sustainability studies have been conducted within a particular place with little attention to the impacts of distant interactions on sustainability in multiple places. Although distant forces have been studied, they are usually treated as exogenous variables and feedbacks have been rarely considered. To understand and integrate various distant interactions better, we propose an integrated framework based on telecoupling – an umbrella concept that refers to socioeconomic and environmental interactions over distances. The concept of telecoupling is a logical extension of research on coupled human and natural systems, in which human and natural systems interact within particular places. The telecoupling framework contains five major interrelated components (coupled human and natural systems, agents, flows, causes, and effects). We illustrate the framework using two examples of distant interactions, highlight the implications of the framework, and discuss research needs and approaches to move research on telecouplings forward. The framework can help better analyze system components and their interrelationships, identify research gaps, detect hidden costs and untapped benefits, provide a useful means to incorporate feedbacks as well as trade-offs and synergies across multiple places (sending, receiving, and spillover systems), and improve the understanding of distant interactions and the effectiveness of policies for socioeconomic and environmental sustainability from local to global levels.

  12. Development of MnCoO Coating with New Aluminizing Process for Planar SOFC Stacks

    SciTech Connect (OSTI)

    Choi, Jung-Pyung; Weil, K. Scott; Chou, Y. S.; Stevenson, Jeffry W.; Yang, Zhenguo

    2011-03-22

    Low-cost, chromia-forming steels find widespread use in SOFCs at operating temperatures below 800C, because of their low thermal expansion mismatch and low cost. However, volatile Cr-containing species originating from this scale poison the cathode material in the cells and subsequently cause power degradation in the devices. To prevent this, a conductive manganese cobaltite coating has been developed. However, this coating is not compatible with forming hermetic seals between the interconnect or window frame component and ceramic cell. This coating reacts with sealing materials. Thus, a new aluminizing process has been developed for the sealing regions in these parts, as well as for other metallic stack and balance-of-plant components. From this development, the sealing performance and SOFC stack performance became very stable.

  13. RussiaSNL2-web.indd

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fast ignition simulation. Modifi ed for the Web Under this contract, VNIITF will complete development of a hybrid implicit code using adaptive mesh refi ne- ment and use that code ...

  14. Research and Development of a Low Cost Solar Collector

    SciTech Connect (OSTI)

    Ansari, Asif; Philip, Lee; Thouppuarachchi, Chirath

    2012-08-01

    This is a Final Technical Report on the Research and Development completed towards the development of a Low Cost Solar Collector conducted under the DOE cost-sharing award EE-0003591. The objective of this project was to develop a new class of solar concentrators with geometries and manufacturability that could significantly reduce the fully installed cost of the solar collector field for concentrated solar thermal power plants. The goal of the project was to achieve an aggressive cost target of $170/m2, a reduction of up to 50% in the total installed cost of a solar collector field as measured against the current industry benchmark of a conventional parabolic trough. The project plan, and the detailed activities conducted under the scope of the DOE Award project addressed all major drivers that affect solar collector costs. In addition to costs, the study also focused on evaluating technical performance of new collector architectures and compared them to the performance of the industry benchmark parabolic trough. The most notable accomplishment of this DOE award was the delivery of a full-scale integrated design, manufacturing and field installation solution for a new class of solar collector architecture which has been classified as the Bi-Planar Fresnel Collector (BPFC) and may be considered as a viable alternative to the conventional parabolic trough, as well as the conventional Fresnel collectors. This was in part accomplished through the design and development, all the way through fabrication and test validation of a new class of Linear Planar Fresnel Collector architecture. This architecture offers a number of key differentiating features which include a planar light-weight frame geometry with small mass-manufacturable elements utilizing flat mirror sections. The designs shows significant promise in reducing the material costs, fabrication costs, shipping costs, and on-site field installation costs compared to the benchmark parabolic trough, as well as the conventional Fresnel collector. The noteworthy design features of the BPFC architecture include the use of relatively cheaper flat mirrors and a design which allows the mirror support beam sections to act as load-bearing structural elements resulting in more than a 36% reduction in the overall structural weight compared to an optimized parabolic trough. Also, it was shown that the utilization of small mass-produced elements significantly lowers mass-production and logistics costs that can more quickly deliver economies of scale, even for smaller installations while also reducing shipping and installation costs. Moreover, unlike the traditional Fresnel trough the BPFC architecture does not require complex articulating drive mechanisms but instead utilizes a standard parabolic trough hydraulic drive mechanism. In addition to the development of the Bi-Planar Fresnel Collector, an optimized conventional space-frame type parabolic trough was also designed, built, analyzed and field-tested during the first phase of this award. The design of the conventional space-frame parabolic collector was refined with extensive FEA and CFD analysis to reduce material costs and re-designed for simpler fabrication and more accurate lower-cost field assembly. This optimized parabolic trough represented an improvement over the state-of-the art of the traditional parabolic trough architecture and also served as a more rigorous and less subjective benchmark that was used for comparison of new candidate design architectures. The results of the expanded 1st phase of the DOE award project showed that both the Optimized Parabolic Trough and the new Bi-Planar Fresnel Collector design concepts failed to meet the primary objectives for the project of achieving a 50% cost reduction from the industry reference total installed cost of $350/m2. Results showed that the BPFC came in at projected total installed cost of $237/m2 representing a 32% savings compared to the industry benchmark conventional parabolic trough. And the cost reduction obtained by the Optimized Parabolic Trough compared to the

  15. Hanford Site Development Plan

    SciTech Connect (OSTI)

    Rinne, C.A.; Curry, R.H.; Hagan, J.W.; Seiler, S.W.; Sommer, D.J. ); Yancey, E.F. )

    1990-01-01

    The Hanford Site Development Plan (Site Development Plan) is intended to guide the short- and long-range development and use of the Hanford Site. All acquisition, development, and permanent facility use at the Hanford Site will conform to the approved plan. The Site Development Plan also serves as the base document for all subsequent studies that involve use of facilities at the Site. This revision is an update of a previous plan. The executive summary presents the highlights of the five major topics covered in the Site Development Plan: general site information, existing conditions, planning analysis, Master Plan, and Five-Year Plan. 56 refs., 67 figs., 31 tabs.

  16. DEVELOPING STATE POLICIES SUPPORTIVE OF BIOENERGY DEVELOPMENT

    SciTech Connect (OSTI)

    Kathryn Baskin

    2005-04-30

    Working within the context of the Southern States Biobased Alliance (SSBA) and with officials in each state, the Southern States Energy Board (SSEB) is identifying bioenergy-related policies and programs within each state to determine their impact on the development, deployment or use of bioenergy. In addition, SSEB will determine which policies have impacted industry's efforts to develop, deploy or use biobased technologies or products. As a result, SSEB will work with the Southern States Biobased Alliance to determine how policy changes might address any negative impacts or enhance positive impacts. In addition to analysis of domestic policies and programs, this project will include the development of a U.S.-Brazil Biodiesel Pilot Project. The purpose of this effort is to promote and facilitate the commercialization of biodiesel and bioenergy production and demand in Brazil.

  17. DEVELOPING STATE POLICIES SUPPORTIVE OF BIOENERGY DEVELOPMENT

    SciTech Connect (OSTI)

    Kathryn Baskin

    2004-10-31

    Working within the context of the Southern States Biobased Alliance (SSBA) and with officials in each state, the Southern States Energy Board (SSEB) is identifying bioenergy-related policies and programs within each state to determine their impact on the development, deployment or use of bioenergy. In addition, SSEB will determine which policies have impacted industry's efforts to develop, deploy or use biobased technologies or products. As a result, SSEB will work with the Southern States Biobased Alliance to determine how policy changes might address any negative impacts or enhance positive impacts. In addition to analysis of domestic policies and programs, this project will include the development of a U.S.-Brazil Biodiesel Pilot Project. The purpose of this effort is to promote and facilitate the commercialization of biodiesel and bioenergy production and demand in Brazil.

  18. DEVELOPING STATE POLICIES SUPPORTIVE OF BIOENERGY DEVELOPMENT

    SciTech Connect (OSTI)

    Kathryn Baskin

    2002-11-01

    Working within the context of the Southern States Biobased Alliance (SSBA) and with officials in each state, the Southern States Energy Board (SSEB) is identifying bioenergy-related policies and programs within each state to determine their impact on the development, deployment or use of bioenergy. In addition, SSEB will determine which policies have impacted industry's efforts to develop, deploy or use biobased technologies or products. As a result, SSEB will work with the Southern States Biobased Alliance to determine how policy changes might address any negative impacts or enhance positive impacts.

  19. DEVELOPING STATE POLICIES SUPPORTIVE OF BIOENERGY DEVELOPMENT

    SciTech Connect (OSTI)

    Kathryn Baskin

    2002-07-31

    Working within the context of the Southern States Biobased Alliance (SSBA) and with officials in each state, the Southern States Energy Board (SSEB) is identifying bioenergy-related policies and programs within each state to determine their impact on the development, deployment or use of bioenergy. In addition, SSEB will determine which policies have impacted industry's efforts to develop, deploy or use biobased technologies or products. As a result, SSEB will work with the Southern States Biobased Alliance to determine how policy changes might address any negative impacts or enhance positive impacts.

  20. Developing Alaskan Sustainable Housing

    Broader source: Energy.gov [DOE]

    The Association of Alaska Housing Authorities is holding a 3-day training event for housing development professionals titled Developing Alaskan Sustainable Housing (DASH). This is a unique...

  1. PGE Renewable Development Fund

    Broader source: Energy.gov [DOE]

    PGE is accepting applications for 2016 Renewable Development Fund awards through June 27 (5:00 PM PDT).

  2. PHOTOGRAPHIC FILM DEVELOPER

    DOE Patents [OSTI]

    Berry, F.G.

    1958-06-24

    S>An improved photographic developer is presented having very high energy development fine grain characteristics and a long shelf life. These characteristics are obtained by the use of aminoacetic acid in the developer, the other constituents of which are: sodium sulfite, hydroquinone, sodiunn borate, boric acid and potassium bromide, 1-phenyl-3-pyrazolidone.

  3. Mechanisms in Plant Development

    SciTech Connect (OSTI)

    Hake, Sarah

    2013-08-21

    This meeting has been held every other year for the past twenty-two years and is the only regularly held meeting focused specifically on plant development. Topics covered included: patterning in developing tissues; short and long distance signaling; differentiation of cell types; the role of epigenetics in development; evolution; growth.

  4. Assessing the Importance of Nonlinearities in the Development of a Substructure Model for the Wind Turbine CAE Tool FAST: Preprint

    SciTech Connect (OSTI)

    Damiani, R.; Jonkman, J.; Robertson, A.; Song, H.

    2013-03-01

    Design and analysis of wind turbines are performed using aero-servo-elastic tools that account for the nonlinear coupling between aerodynamics, controls, and structural response. The NREL-developed computer-aided engineering (CAE) tool FAST also resolves the hydrodynamics of fixed-bottom structures and floating platforms for offshore wind applications. This paper outlines the implementation of a structural-dynamics module (SubDyn) for offshore wind turbines with space-frame substructures into the current FAST framework, and focuses on the initial assessment of the importance of structural nonlinearities. Nonlinear effects include: large displacements, axial shortening due to bending, cross-sectional transverse shear effects, etc.

  5. SES Executive Development

    Broader source: Energy.gov [DOE]

    Development continues once an individual enters into the SES. Faced with constant challenges, changing technologies and a fluid environment, executives need to pursue ongoing professional executive development. It is crucial that executives continue to strengthen and reinforce their Executive Core Qualifications (ECQs), skills and knowledge. http://www.opm.gov/ses/executive_development/index.asp Federal agencies are required by law (Title 5, U.S. Code, Section 3396) to establish programs for the continuing development of senior executives. DOE’s Office of Learning & Workforce Development is available to assist you in determining a course of action your executive development. They have a guidebook that “contains descriptions of over 350 courses, offered by 56 colleges and universities throughout the continental United States as well as by the Office of Personnel Management.”

  6. Wineagle Developers | Open Energy Information

    Open Energy Info (EERE)

    Developers Jump to: navigation, search Name: Wineagle Developers Place: Sacramento, California Zip: 95814 Sector: Geothermal energy Product: Geothermal developer in...

  7. Sandia Energy - Advanced Research & Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Advanced Research & Development Home Stationary Power Energy Conversion Efficiency Solar Energy Photovoltaics Advanced Research & Development Advanced Research & DevelopmentCoryne...

  8. Regional Economic Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Regional Economic Development Regional Economic Development Supporting companies in every stage of development through access to technology, technical assistance or investment Questions Richard P. Feynman Center for Innovation Regional Programs (505) 665-9090 New Mexico Small Business Assistance Email Venture Acceleration Fund Email DisrupTECH Email SBIR/STTR Email FCI facilitates commercialization in New Mexico to accelerate and enhance our efforts to convert federal and state research

  9. WINDExchange: Wind Economic Development

    Wind Powering America (EERE)

    Development WINDExchange provides software applications and publications to help individuals, developers, local governments, and utilities make decisions about wind power. Projecting costs and benefits of new installations, including the economic development impacts created, is a key element in looking at potential wind applications. Communities, states, regions, job markets (i.e., construction, operations and maintenance), the tax base, tax revenues, and others can be positively affected. These

  10. Blind shaft development

    SciTech Connect (OSTI)

    Fiscor, S.

    2009-02-15

    The article discusses how Shaft Drillers International (SDI) is breaking new ground in shaft development and ground stabilization. Techniques of blind shaft drilling and raise bore shaft development developed by SDI are briefly explained. An associated company, Coastal Drilling East, deals with all types of ground improvement such as pre-grouting work for shafts, grouting of poor soil and water leaks into the mine. 3 photos.

  11. ORISE: Web Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Web Development As computer-based applications become increasingly popular for the delivery of health care training and information, the need for Web development in support of these tools continues to grow. The Oak Ridge Institute for Science and Education (ORISE) provides Web development capabilities to government agencies and organizations interested in converting training and education programs based on traditional means of communication into a variety of tools that suit the technology skills

  12. TRANSIMS Interface Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    transims TRANSIMS Interface Development TRACC RESEARCH Computational Fluid Dynamics Computational Structural Mechanics Transportation Systems Modeling TRANSIMS Studio (Figure 1) has been developed by TRACC for the TRANSIMS community as part of the TRANSIMS Open Source project. It provides an integrated development environment (IDE) for TRANSIMS by combining a number of components that work seamlessly with each other. The visible part of the IDE is the graphical user interface (GUI) that allows

  13. National Fertilizer Development Center

    Office of Legacy Management (LM)

    Disposition of equipment utilized in the project was not known. The process, originally developed by Dox Chemical Company of Pittsburgh, California, involved saparation of lJaO ...

  14. New Commercial Program Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New Commercial Program Development Commercial Current Promotions Industrial Federal Agriculture Beginning in spring of 2015, the BPA Commercial Team will be working with utilities...

  15. Sustainable Development Conference

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    award at Sustainable Development Conference October 22, 2015 LANL Researchers Yongchao Yang, Alessandro Cattaneo and David Mascareas of the National Security Education...

  16. Requirements for Wind Development

    Broader source: Energy.gov [DOE]

    In 2015 Oklahoma amended the Oklahoma Wind Energy Development Act. The amendments added new financial security requirements, setback requirements, and notification requirements for wind energy...

  17. SRNL LDRD - Developed Technologies

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Developed Technologies Porous Wall Hollow Glass Microspheres Porous Wall Hollow Glass Microspheres Tiny Glass Spheres for Energy Storage, Medical Applications and Other Uses...

  18. Lighting Developments to 2030

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power ... Lighting Technologies, Costs, and Energy Demand: Global Developments to 2030 View Slides: ...

  19. Energy Education & Workforce Development

    Office of Environmental Management (EM)

    I. Introduction of the Energy Literacy and Energy 101 Initiatives -Michelle Fox & Matt Garcia II. Energy 101 Curricular Framework Development - Jim Turner III. Energy 101 ...

  20. SES CANDIDATE DEVELOPMENT PROGRAM

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    6 (11-03) SENIOR EXECUTIVE SERVICE CANDIDATE DEVELOPMENT PROGRAM (SESCDP) Evaluation of Formal Training DATE:... CANDIDATE NAME: TITLE OF TRAINING PROGRAM: VENDOR...

  1. Economic Development Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Veolia has purchased Kurion, a startup company that developed modules used for cleanup of radioactively contaminated water following the Fukushima, Japan nuclear disaster. more... ...

  2. Long Range Development Plan

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    scientific missions. Science drives the Lab's development. LRDPs establish a framework of land-use principles and policies to guide future growth and change through 2025. The plan...

  3. Development of a Thin-Wall Magnesium side door Inner Panel for Automobiles

    SciTech Connect (OSTI)

    Jekl, J.; Auld, J.; Sweet, C.; Carter, Jon; Resch, Steve; Klarner, A.; Brevick, J.; Luo, A.

    2015-05-17

    Cast magnesium side door inner panels can provide a good combination of weight, functional, manufacturing and economical requirements. However, several challenges exist including casting technology for thin-wall part design, multi-material incompatibility and relatively low strength vs steel. A project has been initiated, supported by the US Department of Energy, to design and develop a lightweight frame-under-glass door having a thin-wall, full die-cast, magnesium inner panel. This development project is the first of its kind within North America. Phase I of the project is now complete and the 2.0mm magnesium design, through casting process enablers, has met or exceeded all stiffness requirements, with significant mass reduction and part consolidation. In addition, a corrosion mitigation strategy has been established using industry-accepted galvanic isolation methods and coating technologies.

  4. Wind Economic Development (Postcard)

    SciTech Connect (OSTI)

    Not Available

    2011-08-01

    The U.S. Department of Energy's Wind Powering America initiative provides information on the economic development benefits of wind energy. This postcard is a marketing piece that stakeholders can provide to interested parties; it will guide them to the economic development benefits section on the Wind Powering America website.

  5. Technical Assistance to Developers

    SciTech Connect (OSTI)

    Rockward, Tommy; Borup, Rodney L.; Garzon, Fernando H.; Mukundan, Rangachary; Spernjak, Dusan

    2012-07-17

    This task supports the allowance of technical assistance to fuel-cell component and system developers as directed by the DOE. This task includes testing of novel materials and participation in the further development and validation of single cell test protocols. This task also covers technical assistance to DOE Working Groups, the U.S. Council for Automotive Research (USCAR) and the USCAR/DOE Driving Research and Innovation for Vehicle efficiency and Energy sustainability (U.S. Drive) Fuel Cell Technology Team. Assistance includes technical validation of new fuel cell materials and methods, single cell fuel cell testing to support the development of targets and test protocols, and regular advisory participation in other working groups and reviews. This assistance is made available to PEM fuel cell developers by request and DOE Approval. The objectives are to: (1) Support technically, as directed by DOE, fuel cell component and system developers; (2) Assess fuel cell materials and components and give feedback to developers; (3) Assist the DOE Durability Working Group with the development of various new material durability Testing protocols; and (4) Provide support to the U.S. Council for Automotive Research (USCAR) and the USCAR/DOE Fuel Cell Technology Team. FY2012 specific technical objectives are: (1) Evaluate novel MPL materials; (2) Develop of startup/ shutdown protocol; (3) Test the impact of hydrophobic treatment on graphite bi-polar plates; (4) Perform complete diagnostics on metal bi-polar plates for corrosion; and (5) Participate and lead efforts in the DOE Working Groups.

  6. Reference Model Development

    SciTech Connect (OSTI)

    Jepsen, Richard

    2011-11-02

    Presentation from the 2011 Water Peer Review in which principal investigator discusses project progress to develop a representative set of Reference Models (RM) for the MHK industry to develop baseline cost of energy (COE) and evaluate key cost component/system reduction pathways.

  7. Aggressive development plans

    SciTech Connect (OSTI)

    McCandless, D.H.

    1993-11-01

    Hydropower developments are capital-intensive, are subject to uncertainty in water availability, and have a somewhat higher construction-cost risk than thermal projects. However, a developer who selects an attractive site, arranges a good financial package, and designs and constructs a well-conceived hydropower project can earn an attractive long-term return while providing a dependable, low-cost source of energy to consumers. In the Philippines, many attractive hydropower sites are now available. As demonstrated by the attendance at the US Trade and Development Agency-sponsored Symposium on Power Development and Investment Opportunities in the Philippines, in Washington, D.C., on Sept. 21 and 22, 1993, there is a growing interest in private hydropower. Following its successful record in implementing thermal private power developments, the Philippines now offers many attractive opportunities to exploit its tremendous potential in the hydropower sector.

  8. NREL Improves Access to Building Product Energy Data (Fact Sheet), NREL Highlights in Research & Development, NREL (National Renewable Energy Laboratory)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technology Performance Exchange helps move projects to implementation. A new Web-based tool enables users to evaluate the site-specific performance of various building technolo- gies, support more effective financial analyses, and make better-informed procure- ment decisions. By improving stakeholders' confidence in performance, the Technol- ogy Performance Exchange(tm) (TPEx(tm)) is streamlining access to foundational energy performance data and helping many viable energy efficiency projects

  9. Liga developer apparatus system

    DOE Patents [OSTI]

    Boehme, Dale R.; Bankert, Michelle A.; Christenson, Todd R.

    2003-01-01

    A system to fabricate precise, high aspect ratio polymeric molds by photolithograpic process is described. The molds for producing micro-scale parts from engineering materials by the LIGA process. The invention is a developer system for developing a PMMA photoresist having exposed patterns comprising features having both very small sizes, and very high aspect ratios. The developer system of the present invention comprises a developer tank, an intermediate rinse tank and a final rinse tank, each tank having a source of high frequency sonic agitation, temperature control, and continuous filtration. It has been found that by moving a patterned wafer, through a specific sequence of developer/rinse solutions, where an intermediate rinse solution completes development of those portions of the exposed resist left undeveloped after the development solution, by agitating the solutions with a source of high frequency sonic vibration, and by adjusting and closely controlling the temperatures and continuously filtering and recirculating these solutions, it is possible to maintain the kinetic dissolution of the exposed PMMA polymer as the rate limiting step.

  10. Jobs and Economic Development Modeling

    Office of Energy Efficiency and Renewable Energy (EERE)

    Project objective: Develop models to estimate jobs and economic impacts from geothermal project development and operation.

  11. Microsystem product development.

    SciTech Connect (OSTI)

    Polosky, Marc A.; Garcia, Ernest J.

    2006-04-01

    Over the last decade the successful design and fabrication of complex MEMS (MicroElectroMechanical Systems), optical circuits and ASICs have been demonstrated. Packaging and integration processes have lagged behind MEMS research but are rapidly maturing. As packaging processes evolve, a new challenge presents itself, microsystem product development. Product development entails the maturation of the design and all the processes needed to successfully produce a product. Elements such as tooling design, fixtures, gages, testers, inspection, work instructions, process planning, etc., are often overlooked as MEMS engineers concentrate on design, fabrication and packaging processes. Thorough, up-front planning of product development efforts is crucial to the success of any project.

  12. Economic Development Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Development Office Is your technology business looking for a door to the Laboratory? The Economic Development Office at PNNL is here to help you start, grow, or relocate your business. We help you tap into technology experts, facilities, and other resources available at the Laboratory...some at no cost to you. We've helped more than 400 companies in our region and 100 more nationwide. Our goals: to expand the economy's technology sector and create high-value jobs. Economic Development

  13. Advanced Turbine Systems (ATS) program conceptual design and product development

    SciTech Connect (OSTI)

    1996-08-31

    Achieving the Advanced Turbine Systems (ATS) goals of 60% efficiency, single-digit NO{sub x}, and 10% electric power cost reduction imposes competing characteristics on the gas turbine system. Two basic technical issues arise from this. The turbine inlet temperature of the gas turbine must increase to achieve both efficiency and cost goals. However, higher temperatures move in the direction of increased NO{sub x} emission. Improved coatings and materials technologies along with creative combustor design can result in solutions to achieve the ultimate goal. GE`s view of the market, in conjunction with the industrial and utility objectives, requires the development of Advanced Gas Turbine Systems which encompass two potential products: a new aeroderivative combined-cycle system for the industrial market, and a combined-cycle system for the utility sector that is based on an advanced frame machine. The GE Advanced Gas Turbine Development program is focused on two specific products: (1) a 70 MW class industrial gas turbine based on the GE90 core technology utilizing an innovative air cooling methodology; (2) a 200 MW class utility gas turbine based on an advanced Ge heavy-duty machine utilizing advanced cooling and enhancement in component efficiency. Both of these activities required the identification and resolution of technical issues critical to achieving ATS goals. The emphasis for the industrial ATS was placed upon innovative cycle design and low emission combustion. The emphasis for the utility ATS was placed on developing a technology base for advanced turbine cooling, while utilizing demonstrated and planned improvements in low emission combustion. Significant overlap in the development programs will allow common technologies to be applied to both products. GE Power Systems is solely responsible for offering GE products for the industrial and utility markets.

  14. developing-compute-efficient

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Developing Compute-efficient, Quality Models with LS-PrePost 3 on the TRACC Cluster Oct. ... with an emphasis on applying these capabilities to build computationally efficient models. ...

  15. HTL Model Development

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1.3.4.100 HTL Model Development MARCH 24, 2015 ALGAE Sue Jones Yunhua Zhu, Lesley Snowden-Swan, Dan Anderson, Rich Hallen, Karl Albrecht, Doug Elliott, Andy Schmidt Pacific ...

  16. JPRS report, nuclear developments

    SciTech Connect (OSTI)

    1991-03-28

    This report contains articles concerning the nuclear developments of the following countries: (1) China; (2) Japan, North Korea, South Korea; (3) Bulgaria; (4) Argentina, Brazil, Honduras; (5) India, Iran, Pakistan, Syria; (6) Soviet Union; and (7) France, Germany, Turkey.

  17. Advanced Interconnect Development

    SciTech Connect (OSTI)

    Yang, Z.G.; Maupin, G.; Simner, S.; Singh, P.; Stevenson, J.; Xia, G.

    2005-01-27

    The objectives of this project are to develop cost-effective, optimized materials for intermediate temperature SOFC interconnect and interconnect/electrode interface applications and identify and understand degradation processes in interconnects and at their interfaces with electrodes.

  18. SSL Technology Development Workshop

    Broader source: Energy.gov [DOE]

    Rapid advances make it easy to forget that SSL technology is still at a relatively early stage of development, and much of its potential remains untapped. The 10th annual DOE SSL Technology...

  19. Acquisition Career Development Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2004-04-19

    This Order establishes training and certification requirements and career development programs under the Acquisition Career Development (ACD) Program for DOE and NNSA acquisition workforce. The acquisition workforce includes contracting, purchasing, personal property management, program management, Contracting Officers and Contracting Officer Representatives. The ACD Program implements the Office of Federal Procurement Policy (OFPP) requirements, Federal Acquisition Regulation (FAR) requirements, Federal Acquisition Reform Act (FARA) requirements, and the objectives of Executive Order (E.O.) 129231, Federal Procurement Reform, dated 10-13-1994. This order cancels DOE O 361.1, Acquisition Career Development Program, dated 11-10-99, AND Acquisition Letter 2003-05, Personal Property Management Career Development, Training, and Certification Program, dated 9-10-03. Cancels DOE O 361.1 Chg 2. Canceled by DOE O 361.1B.

  20. SSL TECHNOLOGY DEVELOPMENT WORKSHOP

    Broader source: Energy.gov [DOE]

    Rapid advances in SSL technology make it easy to forget that this technology is still at a relatively early stage of development, and much of its potential remains untapped. The 10th annual DOE SSL...

  1. DOE Tour of Zero: The Singer Village by Brookside Development...

    Broader source: Energy.gov (indexed) [DOE]

    the walls and a continuous thermal blanket of rigid foam on the exterior of the wall framing. 9 of 10 Every ceiling seam and penetration of the home is sealed with expanding...

  2. DOE Zero Energy Ready Home Case Study: Weiss Building & Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    has advanced framed walls with R-23 dense-packed fiberglass plus R-13 rigid polyiso, a sealed attic with open-cell spray foam, a pier foundation, and 95% efficient gas furnace. ...

  3. UNIRIB: Equipment Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Equipment Development Technical Developments and Equipment In close collaboration with Holifield Radioactive Ion Beam Facility (HRIBF) scientists, researchers at University Radioactive Ion Beam (UNIRIB) consortium universities are offered the opportunity to perform low-energy nuclear structure research using radioactive/stable ion beams and experimental equipment available through HRIBF. UNIRIB, a division of the Oak Ridge Institute for Science and Education (ORISE), provides not only funding,

  4. Transmission Developers Inc.

    Energy Savers [EERE]

    ' % ~ Transmission Developers Inc. July 7, 2011 Mr. Anthony J. Como Director, Permitting and Siting Office ofElectricity Delivery and Energy Reliability (OE-20) U.S. Department of Energy 1000 Independence A venue SW, Room 8G-024 Washington, D.C. 20585 Subject: Champlain Hudson Power Express Project U.S. Department of Energy Presidential Permit Application PP-362 Dear Mr. Como: On January 25, 2010, Transmission Developers, Inc. ("TDI'' or "Applicants") submitted on behalf of

  5. ORISE: Health Literacy Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Literacy Development While health disparities may be attributed to a number of factors, health literacy development and access to health information can help special populations gain a better understanding of wellness and prevention. The Internet and other means of electronic communication have become popular tools that are allowing people to take control of their health. According to Healthy People 2010, nearly half of American adults (90 million people) are deemed "health

  6. ORISE: Standards development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Standards development For 30 years, health physicists with the Oak Ridge Institute for Science and Education (ORISE) have actively participated in the development of industry standards that provide guidance and support to decontamination and decommissioning projects across the United States. Because of our extensive experience conducting radiological surveys and site characterization, our federal agency customers, such as the U.S. Nuclear Regulatory Commission (NRC) and the U.S. Department of

  7. Acquisition Career Development Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-12-20

    To set forth requirements and responsibilities for the Department of Energy (DOE) Acquisition Career Development (ACD) Program, which implements Office of Federal Procurement Policy (OFPP) requirements, Federal Acquisition Regulation (FAR) requirements, Federal Acquisition Reform Act (FARA) requirements, and the career development objectives of Executive Order (E.O.) 12931. Change 1 approved 12-20-2001. Cancels DOE O 361.1. Canceled by DOE O 361.1 Chg 2.

  8. Acquisition Career Development Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2003-06-13

    To set forth requirements and responsibilities for the Department of Energy (DOE) Acquisition Career Development (ACD) Program, which implements Office of Federal Procurement Policy (OFPP) requirements, Federal Acquisition Regulation (FAR) requirements, Federal Acquisition Reform Act (FARA) requirements, and the career development objectives of Executive Order (E.O.) 12931. Change 1 approved 12-20-2001. Change 2 approved 06-13-03. Cancels DOE O 361.1 Chg 1. Canceled by DOE O 361.1A.

  9. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: clean energy Type Term Title Author Replies Last Post sort icon Blog...

  10. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: citation Type Term Title Author Replies Last Post sort icon Blog entry...

  11. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: citing Type Term Title Author Replies Last Post sort icon Blog entry...

  12. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: Energy Visions Prize Type Term Title Author Replies Last Post sort icon...

  13. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: cleanweb Type Term Title Author Replies Last Post sort icon Blog entry...

  14. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: Energy data Type Term Title Author Replies Last Post sort icon Blog...

  15. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: funding Type Term Title Author Replies Last Post sort icon Blog entry...

  16. Bolivia renewable energy development

    SciTech Connect (OSTI)

    Smith, P.

    1997-12-01

    The author summarizes changes which have occurred in Bolivia in the past year which have had an impact on renewable energy source development. Political changes have included the privatization of power generation and power distribution, and resulted in a new role for state level government and participation by the individual. A National Rural Electrification Plan was adopted in 1996, which stresses the use of GIS analysis and emphasizes factors such as off grid, economic index, population density, maintenance risk, and local organizational structure. The USAID program has chosen to stress economic development, environmental programs, and health over village power programs. The national renewables program has adopted a new development direction, with state projects, geothermal projects, and private sector involvement stressed.

  17. Power Systems Development Facility

    SciTech Connect (OSTI)

    Southern Company Services

    2009-01-31

    In support of technology development to utilize coal for efficient, affordable, and environmentally clean power generation, the Power Systems Development Facility (PSDF), located in Wilsonville, Alabama, has routinely demonstrated gasification technologies using various types of coals. The PSDF is an engineering scale demonstration of key features of advanced coal-fired power systems, including a Transport Gasifier, a hot gas particulate control device, advanced syngas cleanup systems, and high-pressure solids handling systems. This final report summarizes the results of the technology development work conducted at the PSDF through January 31, 2009. Twenty-one major gasification test campaigns were completed, for a total of more than 11,000 hours of gasification operation. This operational experience has led to significant advancements in gasification technologies.

  18. Graphite Technology Development Plan

    SciTech Connect (OSTI)

    W. Windes; T. Burchell; M.Carroll

    2010-10-01

    The Next Generation Nuclear Plant (NGNP) will be a helium-cooled High Temperature Gas Reactor (HTGR) with a large graphite core. Graphite physically contains the fuel and comprises the majority of the core volume. Graphite has been used effectively as a structural and moderator material in both research and commercial high-temperature gas-cooled reactors. This development has resulted in graphite being established as a viable structural material for HTGRs. While the general characteristics necessary for producing nuclear grade graphite are understood, historical nuclear grades no longer exist. New grades must be fabricated, characterized, and irradiated to demonstrate that current grades of graphite exhibit acceptable non-irradiated and irradiated properties upon which the thermomechanical design of the structural graphite in NGNP is based. This Technology Development Plan outlines the research and development (R&D) activities and associated rationale necessary to qualify nuclear grade graphite for use within the NGNP reactor.

  19. Guidebook on biogas development

    SciTech Connect (OSTI)

    Not Available

    1980-01-01

    This guidebook covers the practical aspects of small-scale biogas development suitable for use in rural areas in developing countries, especially those of the ESCAP region. It is intended that all aspects of biogas are covered so that someone with no knowledge of the subject can, with confidence, design, build, operate and maintain a biogas plant. Information on biogas technology in China is also included. Chapters cover: the biogas process; factors effecting gas-plant design and operation; the classification and design principles of plants; design, size and site selection; the construction of digesters; gas holders and pipes; household gas appliances and their use; starting and operating a biogas digester; servicing and safety; improving gas-plant performance; commercial uses of biogas; the effluent and its uses, biogas-plant development programmes; community plants; and economics. In the annexes, designs for biogas plants of the fixed-dome, bag and floating gas-holder type are presented. 9 references.

  20. Exciting new PDSF developments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Exciting new PDSF developments Exciting new PDSF developments February 25, 2014 I'm pleased to announce that PDSF successfully deployed new login nodes last week. Some of you may already have noticed that you are now landing on nodes named pdsf[6-8] when you ssh to pdsf.nersc.gov. Our new login nodes use the faster Mendel IB network and more modern hardware. We've gone from four nodes to three but, because each node has a higher core count, the processing power is staying the same. The old

  1. Hydropower research and development

    SciTech Connect (OSTI)

    1997-03-01

    This report is a compilation of information on hydropower research and development (R and D) activities of the Federal government and hydropower industry. The report includes descriptions of on-going and planned R and D activities, 1996 funding, and anticipated future funding. Summary information on R and D projects and funding is classified into eight categories: fish passage, behavior, and response; turbine-related; monitoring tool development; hydrology; water quality; dam safety; operations and maintenance; and water resources management. Several issues in hydropower R and D are briefly discussed: duplication; priorities; coordination; technical/peer review; and technology transfer/commercialization. Project information sheets from contributors are included as an appendix.

  2. SES CANDIDATE DEVELOPMENT PROGRAM

    Energy Savers [EERE]

    4 (11-03) SENIOR EXECUTIVE SERVICE CANDIDATE DEVELOPMENT PROGRAM (SESCDP) Supervisor's Evaluation of Candidate's Performance During Developmental Assignment DATE:________________ NAME OF SES CANDIDATE: TITLE OF POSITION: LOCATION OF ASSIGNMENT: ASSIGNMENT DURATION: PART I: EVALUATION OF ASSIGNMENT OBJECTIVES Please evaluate the candidate's level of performance in meeting the objectives of the assignment as Successful or Unacceptable. Objectives Standards Performance Evaluation PLEASE RATE YOUR

  3. About Research & Development

    Broader source: Energy.gov [DOE]

    Next-generation manufacturing technologies will transform industry and open new markets in the United States and around the world. The Advanced Manufacturing Office (AMO) supports Research and Development on technology projects that will help manufacturers become more robust, adaptable, profitable, and globally competitive.

  4. JAGUAR developer's manual.

    SciTech Connect (OSTI)

    Chan, Ethan

    2011-06-01

    JAGUAR (JAva GUi for Applied Research) is a Java software tool providing an advanced text editor and graphical user interface (GUI) to manipulate DAKOTA (Design Analysis Kit for Optimization and Terascale Applications) input specifications. This document focuses on the technical background necessary for a developer to understand JAGUAR.

  5. ECH Technology Development

    SciTech Connect (OSTI)

    Temkin, Richard

    2014-12-24

    Electron Cyclotron Heating (ECH) is needed for plasma heating, current drive, plasma stability control, and other applications in fusion energy sciences research. The program of fusion energy sciences supported by U. S. DOE, Office of Science, Fusion Energy Sciences relies on the development of ECH technology to meet the needs of several plasma devices working at the frontier of fusion energy sciences research. The largest operating ECH system in the world is at DIII-D, consisting of six 1 MW, 110 GHz gyrotrons capable of ten second pulsed operation, plus two newer gyrotrons. The ECH Technology Development research program investigated the options for upgrading the DIII-D 110 GHz ECH system. Options included extending present-day 1 MW technology to 1.3 – 1.5 MW power levels or developing an entirely new approach to achieve up to 2 MW of power per gyrotron. The research consisted of theoretical research and designs conducted by Communication and Power Industries of Palo Alto, CA working with MIT. Results of the study would be validated in a later phase by research on short pulse length gyrotrons at MIT and long pulse / cw gyrotrons in industry. This research follows a highly successful program of development that has led to the highly reliable, six megawatt ECH system at the DIII-D tokamak. Eventually, gyrotrons at the 1.5 megawatt to multi-megawatt power level will be needed for heating and current drive in large scale plasmas including ITER and DEMO.

  6. Marine & hydrokinetic technology development.

    SciTech Connect (OSTI)

    LiVecchi, Al; Jepsen, Richard Alan

    2010-06-01

    The Wind and Water Power Program supports the development of marine and hydrokinetic devices, which capture energy from waves, tides, ocean currents, the natural flow of water in rivers, and marine thermal gradients, without building new dams or diversions. The program works closely with industry and the Department of Energy's national laboratories to advance the development and testing of marine and hydrokinetic devices. In 2008, the program funded projects to develop and test point absorber, oscillating wave column, and tidal turbine technologies. The program also funds component design, such as techniques for manufacturing and installing coldwater pipes critical for ocean thermal energy conversion (OTEC) systems. Rigorous device testing is necessary to validate and optimize prototypes before beginning full-scale demonstration and deployment. The program supports device testing by providing technology developers with information on testing facilities. Technology developers require access to facilities capable of simulating open-water conditions in order to refine and validate device operability. The program has identified more than 20 tank testing operators in the United States with capabilities suited to the marine and hydrokinetic technology industry. This information is available to the public in the program's Hydrodynamic Testing Facilities Database. The program also supports the development of open-water, grid-connected testing facilities, as well as resource assessments that will improve simulations done in dry-dock and closed-water testing facilities. The program has established two university-led National Marine Renewable Energy Centers to be used for device testing. These centers are located on coasts and will have open-water testing berths, allowing researchers to investigate marine and estuary conditions. Optimal array design, development, modeling and testing are needed to maximize efficiency and electricity generation at marine and hydrokinetic power plants while mitigating nearby and distant impacts. Activities may include laboratory and computational modeling of mooring design or research on device spacing. The geographies, resources, technologies, and even nomenclature of the U.S. marine and hydrokinetic technology industry have yet to be fully understood or defined. The program characterizes and assesses marine and hydrokinetic devices, and then organizes the collected information into a comprehensive and searchable Web-based database, the Marine and Hydrokinetic Technology Database. The database, which reflects intergovernmental and international collaboration, provides industry with one of the most comprehensive and up-to-date public resources on marine and hydrokinetic devices.

  7. RELAP-7 Development Updates

    SciTech Connect (OSTI)

    Zhang, Hongbin; Zhao, Haihua; Gleicher, Frederick Nathan; DeHart, Mark David; Zou, Ling; Andrs, David; Martineau, Richard Charles

    2015-09-01

    RELAP-7 is a nuclear systems safety analysis code being developed at the Idaho National Laboratory, and is the next generation tool in the RELAP reactor safety/systems analysis application series. RELAP-7 development began in 2011 to support the Risk Informed Safety Margins Characterization (RISMC) Pathway of the Light Water Reactor Sustainability (LWRS) program. The overall design goal of RELAP-7 is to take advantage of the previous thirty years of advancements in computer architecture, software design, numerical methods, and physical models in order to provide capabilities needed for the RISMC methodology and to support nuclear power safety analysis. The code is being developed based on Idaho National Laboratory’s modern scientific software development framework – MOOSE (the Multi-Physics Object-Oriented Simulation Environment). The initial development goal of the RELAP-7 approach focused primarily on the development of an implicit algorithm capable of strong (nonlinear) coupling of the dependent hydrodynamic variables contained in the 1-D/2-D flow models with the various 0-D system reactor components that compose various boiling water reactor (BWR) and pressurized water reactor nuclear power plants (NPPs). During Fiscal Year (FY) 2015, the RELAP-7 code has been further improved with expanded capability to support boiling water reactor (BWR) and pressurized water reactor NPPs analysis. The accumulator model has been developed. The code has also been coupled with other MOOSE-based applications such as neutronics code RattleSnake and fuel performance code BISON to perform multiphysics analysis. A major design requirement for the implicit algorithm in RELAP-7 is that it is capable of second-order discretization accuracy in both space and time, which eliminates the traditional first-order approximation errors. The second-order temporal is achieved by a second-order backward temporal difference, and the one-dimensional second-order accurate spatial discretization is achieved with the Galerkin approximation of Lagrange finite elements. During FY-2015, we have done numerical verification work to verify that the RELAP-7 code indeed achieves 2nd-order accuracy in both time and space for single phase models at the system level.

  8. Energy Efficiency Project Development

    SciTech Connect (OSTI)

    IUEP

    2004-03-01

    The International Utility Efficiency Partnerships, Inc. (IUEP) has been a leader among the industry groups that have supported voluntary initiatives to promote international energy efficiency projects and address global climate change. The IUEP maintains its leadership by both supporting international greenhouse gas (GHG) reduction projects under the auspices of the U.S. Department of Energy (DOE) and by partnering with U.S. and international organizations to develop and implement strategies and specific energy efficiency projects. The goals of the IUEP program are to (1) provide a way for U.S. industry to maintain a leadership role in international energy efficiency infrastructure projects; (2) identify international energy project development opportunities to continue its leadership in supporting voluntary market-based mechanisms to reduce GHG emissions; and (3) demonstrate private sector commitment to voluntary approaches to global climate issues. The IUEP is dedicated to identifying, promoting, managing, and assisting in the registration of international energy efficiency projects that result in demonstrated voluntary reductions of GHG emissions. This Final Technical Report summarizes the IUEP's work in identifying, promoting, managing, and assisting in development of these projects and IUEP's effort in creating international cooperative partnerships to support project development activities that develop and deploy technologies that (1) increase efficiency in the production, delivery and use of energy; (2) increase the use of cleaner, low-carbon fuels in processing products; and (3) capture/sequester carbon gases from energy systems. Through international cooperative efforts, the IUEP intends to strengthen partnerships for energy technology innovation and demonstration projects capable of providing cleaner energy in a cost-effective manner. As detailed in this report, the IUEP met program objectives and goals during the reporting period January 1, 2001 through December 31, 2002. At the request of the DOE, we have also included in this report additional activities during the reporting period January, 1999 through January, 2001. This additional information had been reported earlier in the Final Technical Reports that summarized activities undertaken in those earlier periods.

  9. e+ e- Factory Developments

    SciTech Connect (OSTI)

    Sullivan, Michael; /SLAC

    2010-08-26

    The impressive performance of current (KEKB) and recent (PEP-II) B-Factory colliders has increased interest in developing even higher luminosity B-factories. Two new designs are being developed (SuperKEKB and SuperB). Both designs plan to deliver a luminosity in the range of 1 x 10{sup 36} cm{sup -2}s{sup -1}, nearly 100 times the present B-factory level. Achieving this high luminosity requires high-current beams and short bunch lengths and/or a new way of colliding the beams. The SuperB design employs a crabbed magnetic waist with a large crossing angle and the SuperKEKB design is looking at crab cavities with high-current beams and/or a travelling focus. I describe the designs being studied to achieve the high luminosity needed for the next generation of B-Factories.

  10. Sustainable Subsurface Energy Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sustainable Subsurface Energy Development - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management

  11. WINDExchange: Workforce Development

    Wind Powering America (EERE)

    Workforce Development A large white cylinder, a portion of a turbine tower, lays horizontally on the ground with three men in safety vests and hard hats standing on the right side and a blue crane on the left side. Several technicians prepare to erect a part of the Gamesa tower at the National Wind Technology Center. Photo by Dennis Schroeder, NREL 20853 The United States needs a skilled and qualified wind energy workforce to produce domestic clean power. Vital industry positions include

  12. Issue Development sheet Blank

    Broader source: Energy.gov [DOE]

    ISSUE DEVELOPMENT SHEET INFORMATION ONLY The information provided below indicates that a potential concern for finding has been identified. Please provide any objective evidence you may have that could either alleviate the concern or eliminate the finding. If no objective evidence is available/can be provided by the end of this audit (at the scheduled end of field work), this information will be included in the audit report and reported as a concern or an audit finding as appropriate.

  13. SES CANDIDATE DEVELOPMENT PROGRAM

    Energy Savers [EERE]

    5 (11-03) SENIOR EXECUTIVE SERVICE CANDIDATE DEVELOPMENT PROGRAM (SESCDP) Candidate Developmental Assignment Evaluation DATE:_______________ NAME OF SES CANDIDATE TITLE OF POSITION LOCATION ASSIGNMENT DURATION: Which Executive Core Qualification(s) was this assignment intended to meet? Leading Change Leading People Results Driven Business Acumen Building Coalitions/Communication Please provide a brief description of your assignment. Did the experience meet your expectation? Was this a good

  14. Issue Development sheet Example

    Broader source: Energy.gov [DOE]

    ISSUE DEVELOPMENT SHEET INFORMATION ONLY The information provided below indicates that a potential concern for finding has been identified. Please provide any objective evidence you may have that could either alleviate the concern or eliminate the finding. If no objective evidence is available/can be provided by the end of this audit (at the scheduled end of field work), this information will be included in the audit report and reported as a concern or an audit finding as appropriate.

  15. OSCARS Developer Community

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Web Browser Interface (WBUI) Web Service Interface (API) Read More... Fasterdata IPv6 Network Network Performance Tools The ESnet Engineering Team Network R&D Software-Defined Networking (SDN) Experimental Network Testbeds Performance (perfSONAR) Software & Tools Development Data for Researchers Partnerships Publications Workshops Science Engagement Move your data Programs & Workshops Science Requirements Reviews Case Studies News & Publications ESnet News Publications and

  16. ARM Raman Lidar Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Development - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear

  17. Update on INSIGHTS Development

    SciTech Connect (OSTI)

    Not Listed; Eric Burgett

    2011-09-01

    INSIGHTS is a transformational separate effects testing capability to perform in situ irradiation studies and characterization of the microscale behavior of nuclear fuel materials under a wide variety of in-pile conditions. Separate effects testing including growth, irradiation, and monitoring of these materials, and encompasses the full science based approach for fuels development from the nanoscale to the mesoscale behavior of the sample material and other defects driven by the modeling and simulation efforts of INL.

  18. Accelerating Advanced Material Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Materials Research in the Information Age Accelerating Advanced Material Development NERSC Science Gateway a 'Google of Material Properties' October 31, 2011 Linda Vu, lvu@lbl.gov, +1 510 495 2402 Kristin Persson is one of the founding scientists behind the Materials Project, a computational tool aimed at taking the guesswork out of new materials discoveries, especially those aimed at energy applications like batteries. (Roy Kaltschmidt, LBNL) New materials are crucial to building a clean energy

  19. XOP: Recent Developments

    Office of Scientific and Technical Information (OSTI)

    XOP: Recent Developments Manuel SBnchez del Woa and Roger 3. Dejus' "European Synchrotron Radiation Facility BP 220, 38043 Grenoble-Cedex, France 'Advanced Photon Source Argonne National Laboratory, Argonne, IL 60439, USA ABSTRACT XOP (X-ray Optics utilities) is a graphical user interface (GUI) to run computer programs which calculate basic information needed by synchrotron radiation beamline scientists and engineers. It can also be used as a front-end for specific codes or packages for

  20. Acquisition Career Development Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1999-11-10

    The Order implements the Department's Acquisition Career Development program, mandatory for professionals in the GS-1102 and 1105 occupational procurement series, as well as others with significant procurement responsibilities. The Order also ensures that members of the acquisition workforce are aware of and adhere to the mandatory training and certification requirements. Cancels Acquisition Letter 98-06. Canceled by DOE O 361.1 Chg 1.

  1. Stirling technology development status

    SciTech Connect (OSTI)

    Dochat, G.R. ); Dudenhoefer, J.E. )

    1993-01-15

    Free-piston Stirling power converters have the potential to meet the many future space power requirements for a wide variety of applications with less mass, better efficiency, and less total area (collector and radiator) than other power converter options. These benefits result in significant dollar savings over the projected mission lifetime. The National Aeronautics and Space Administration (NASA)---Lewis Research Center (LeRC), which has the responsibility to evaluate and develop power technologies that can satisfy anticipated future space mission power requirements, has been developing free-piston Stirling power converters and is bringing the Stirling technology to readiness. As the principal contractor to NASA-LeRC, Mechanical Technology Incorporated (MTI) is under contract to develop the necessary space Stirling technology but also demonstrate the readiness of the technology in two generations of full-scale power converters. The first generation Stirling power converter, the component test power converter (CTPC), initiated cold end testing at the end of 1991, with hot testing scheduled during 1992. This paper reviews test progress of the CTPC including the initial hot engine test results. Modifications incorporated into the CTPC from the earlier space power demonstrator engine are reviewed as well.

  2. NOx Sensor Development

    SciTech Connect (OSTI)

    Woo, L Y; Glass, R S

    2010-11-01

    NO{sub x} compounds, specifically NO and NO{sub 2}, are pollutants and potent greenhouse gases. Compact and inexpensive NO{sub x} sensors are necessary in the next generation of diesel (CIDI) automobiles to meet government emission requirements and enable the more rapid introduction of more efficient, higher fuel economy CIDI vehicles. Because the need for a NO{sub x} sensor is recent and the performance requirements are extremely challenging, most are still in the development phase. Currently, there is only one type of NO{sub x} sensor that is sold commercially, and it seems unlikely to meet more stringent future emission requirements. Automotive exhaust sensor development has focused on solid-state electrochemical technology, which has proven to be robust for in-situ operation in harsh, high-temperature environments (e.g., the oxygen stoichiometric sensor). Solid-state sensors typically rely on yttria-stabilized zirconia (YSZ) as the oxygen-ion conducting electrolyte and then target different types of metal or metal-oxide electrodes to optimize the response. Electrochemical sensors can be operated in different modes, including amperometric (a current is measured) and potentiometric (a voltage is measured), both of which employ direct current (dc) measurements. Amperometric operation is costly due to the electronics necessary to measure the small sensor signal (nanoampere current at ppm NO{sub x} levels), and cannot be easily improved to meet the future technical performance requirements. Potentiometric operation has not demonstrated enough promise in meeting long-term stability requirements, where the voltage signal drift is thought to be due to aging effects associated with electrically driven changes, both morphological and compositional, in the sensor. Our approach involves impedancemetric operation, which uses alternating current (ac) measurements at a specified frequency. The approach is described in detail in previous reports and several publications. Briefly, impedancemetric operation has shown the potential to overcome the drawbacks of other approaches, including higher sensitivity towards NO{sub x}, better long-term stability, potential for subtracting out background interferences, total NO{sub x} measurement, and lower cost materials and operation. Past LLNL research and development efforts have focused on characterizing different sensor materials and understanding complex sensing mechanisms. Continued effort has led to improved prototypes with better performance, including increased sensitivity (to less than 5 ppm) and long-term stability, with more appropriate designs for mass fabrication, including incorporation of an alumina substrate with an imbedded heater. Efforts in the last year to further improve sensor robustness have led to successful engine dynamometer testing with prototypes mounted directly in the engine manifold. Previous attempts had required exhaust gases to be routed into a separate furnace for testing due to mechanical failure of the sensor from engine vibrations. A more extensive cross-sensitivity study was also undertaken this last year to examine major noise factors including fluctuations in water, oxygen, and temperature. The quantitative data were then used to develop a strategy using numerical algorithms to improve sensor accuracy. The ultimate goal is the transfer of this technology to a supplier for commercialization. Due to the recent economic downturn, suppliers are demanding more comprehensive data and increased performance analysis before committing their resources to take the technology to market. Therefore, our NO{sub x} sensor work requires a level of technology development more thorough and extensive than ever before. The objectives are: (1) Develop an inexpensive, rapid-response, high-sensitivity and selective electrochemical sensor for oxides of nitrogen (NO{sub x}) for compression-ignition, direct-injection (CIDI) exhaust gas monitoring; (2) Explore and characterize novel, effective sensing methodologies based on impedance measurements and designs and manufacturing metho

  3. Photonics Research and Development

    SciTech Connect (OSTI)

    Pookpanratana, Sujitra; Shlayan, Neveen; Venkat, Rama; Das, Bisjwajit; Boehm, Bob; Heske, Clemens; Fraser, Donald; Moustakas, Theodore

    2010-01-15

    During the period August 2005 through October 2009, the UNLV Research Foundation (UNLVRF), a non-profit affiliate of the University of Nevada, Las Vegas (UNLV), in collaboration with UNLV’s Colleges of Science and Engineering; Boston University (BU); Oak Ridge National Laboratory (ORNL); and Sunlight Direct, LLC, has managed and conducted a diverse and comprehensive research and development program focused on light-emitting diode (LED) technologies that provide significantly improved characteristics for lighting and display applications. This final technical report provides detailed information on the nature of the tasks, the results of the research, and the deliverables. It is estimated that about five percent of the energy used in the nation is for lighting homes, buildings and streets, accounting for some 25 percent of the average home’s electric bill. However, the figure is significantly higher for the commercial sector. About 60 percent of the electricity for businesses is for lighting. Thus replacement of current lighting with solid-state lighting technology has the potential to significantly reduce this nation’s energy consumption – by some estimates, possibly as high as 20%. The primary objective of this multi-year R&D project has been to develop and advance lighting technologies to improve national energy conversion efficiencies; reduce heat load; and significantly lower the cost of conventional lighting technologies. The UNLVRF and its partners have specifically focused these talents on (1) improving LED technologies; (2) optimizing hybrid solar lighting, a technology which potentially offers the benefits of blending natural with artificial lighting systems, thus improving energy efficiency; and (3) building a comprehensive academic infrastructure within UNLV which concentrates on photonics R&D. Task researchers have reported impressive progress in (1) the development of quantum dot laser emitting diodes (QDLEDs) which will ultimately improve energy efficiency and lower costs for display and lighting applications (UNLV College of Engineering); (2) advancing green LED technology based on the Indium-Gallium-Nitride system (BU), thus improving conversion efficiencies; (3) employing unique state-of-the-art X-ray, electron and optical spectroscopies with microscopic techniques to learn more about the electronic structure of materials and contacts in LED devices (UNLV College of Science); (4) establishing a UNLV Display Lighting Laboratory staffed with a specialized team of academic researchers, students and industrial partners focused on identifying and implementing engineering solutions for lighting display-related problems; and (5) conducting research, development and demonstration for HSL essential to the resolution of technological barriers to commercialization.

  4. Mack LNG vehicle development

    SciTech Connect (OSTI)

    Southwest Research Institute

    2000-01-05

    The goal of this project was to install a production-ready, state-of-the-art engine control system on the Mack E7G natural gas engine to improve efficiency and lower exhaust emissions. In addition, the power rating was increased from 300 brake horsepower (bhp) to 325 bhp. The emissions targets were oxides of nitrogen plus nonmethane hydrocarbons of less than 2.5 g/bhp-hr and particulate matter of less than 0.05 g/bhp-hr on 99% methane. Vehicle durability and field testing were also conducted. Further development of this engine should include efficiency improvements and oxides of nitrogen reductions.

  5. Sustainable Acquisition Developments

    Broader source: Energy.gov [DOE]

    The Administration continues its emphasis on sustainable acquisition. Attached are 2 letters describing recent developments. The first is dated October 5, 2011, from OFPP Administrator, Daniel Gordon, describing the 95% goal, emphasizing the importance of the program and forecasting changes in the Federal Procurement Data System. Second is a letter from the Defense Procurement and Acquisition Policy Office dated October 4, 2011, furnishing some details regarding changes being made in the Federal Procurement Data System to better enable report of accomplishments. Expect to receive more information from the Information Systems Division of the OCIO as the FPDS changes are made.

  6. Workforce Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Learning and Workforce Development » Workforce Development Workforce Development Assessment and Evaluation A structured Training Program Evaluation process has been developed by the Office of Learning and Workforce Development to evaluate the effectiveness and efficiency of DOE training courses and programs, while also ensuring public accountability and compliance with regulatory requirements. Training Evaluation involves the assessment of the effectiveness of training courses and programs.

  7. Eltron Research & Development

    SciTech Connect (OSTI)

    Evenson, Carl; Mackay, Richard; Faull, John

    2014-03-01

    This topical report covers technical work conducted under contract DE-FC26-05NT42469 between FY06 Q1 through FY14 Q2. The project evolved through several budget periods, budget revisions and continuation applications. This report covers work performed under the “base” program. In 2010 ARRA funding was added to the project. A separate report covering the ARRA portion of the project was submitted to DOE. The original project was focused on research and development for scale-up of hydrogen separation membrane for a FutureGen type power plant. The work included membrane testing and evaluation of metal alloy flat plates vs. tubes and metal membranes vs. cermet membranes. In addition, economic analysis and process modeling was performed. The original project team included CoorsTek, NORAM, and Praxair. In FY10Q2 a continuation application was filed for conducting a scale-up test at Eastman Chemical. In this part of the project a Subscale Engineering Prototype (SEP) membrane skid was designed, fabricated, and operated on a gasified coal slip-stream on Eastman’s site in Kingsport, TN. Following operation, the project was reorganized and a second continuation application with a new statement of work was initiated in FY12Q1. Finally, based on DOE’s decision not to proceed with a Process Development Unit (PDU) field test, a third continuation application and statement of work was initiated in FY13Q1 to close out the project.

  8. Ozone transport commission developments

    SciTech Connect (OSTI)

    Joyce, K.M.

    1995-08-01

    On September 27, 1994, the states of the Ozone Transport Commission (OTC) signed an important memorandum of understanding (MOU) agreeing to develop a regional strategy for controlling stationary sources of nitrogen oxide emissions. Specifically, the states of the Ozone Transport Region, OTR, agreed to propose regulations for the control of NOx emissions from boilers and other indirect heat exchangers with a maximum gross heat input rate of at least 250 million BTU per hour. The Ozone Transport Region was divided into Inner, Outer and Northern Zones. States in the Outer Zone agreed to reduce NOx emissions by 55%. States in the Inner Zone agreed to reduce NOx emissions 65%. Facilities in both zones have the option to emit NOx at a rate no greater than 0.2 pounds per million Btu by May 1, 1999. This option provides fairness for the gas-fired plants which already have relatively low NOx emissions. Additionally, States in the Inner and Outer Zones agreed to reduce their NOx emissions by 75% or to emit NOx at a rate no greater than 0.15 pounds per million BTU by May 1, 2003. The Northern Zone States agree to reduce their rate of NOx emissions by 55% from base year levels by May 1, 2003, or to emit NOx at a rate no greater than 0.2 pounds per million BTU. As part of this MOU, States also agreed to develop a regionwide trading mechanism to provide a cost-effective mechanism for implementing the reductions.

  9. Progress Letter Report on Bending Fatigue Test System Development for Spent Nuclear Fuel Vibration Integrity Study (Out-of-cell fatigue testing development - Task 2.4)

    SciTech Connect (OSTI)

    Wang, Jy-An John; Wang, Hong; Cox, Thomas S; Baldwin, Charles A; Bevard, Bruce Balkcom

    2013-08-01

    Vibration integrity of high burn-up spent nuclear fuel in transportation remains to be a critical component of US nuclear waste management system. The structural evaluation of package for spent fuel transportation eventually will need to see if the content or spent fuel is in a subcritical condition. However, a system for testing and characterizing such spent fuel is still lacking mainly due to the complication involved with dealing radioactive specimens in a hot cell environment. Apparently, the current state-of-the-art in spent fuel research and development is quite far away from the delivery of reliable mechanical property data for the assessment of spent fuels in the transport package evaluation. Under the sponsorship of US NRC, ORNL has taken the challenge in developing a robust testing system for spent fuel in hot cell. An extensive literature survey was carried out and unique requirements of such testing system were identified. The U-frame setup has come to the top among various designs examined for reverse bending fatigue test of spent fuel rod. The U-frame has many features that deserve mentioned here: Easy to install spent fuel rod in test; Less linkages than in conventional bending test setup such as three-point or four-point bending; Target the failure mode relevant to the fracture of spent fuel rod in transportation by focusing on pure bending; The continuous calibrations and modifications resulted in the third generation (3G) U-frame testing setup. Rigid arms are split along the LBB axis at rod sample ends. For each arm, this results in a large arm body and an end piece. Mating halves of bushings were modified into two V-shaped surfaces on which linear roller bearings (LRB) are embedded. The rod specimen is installed into the test fixture through opening and closing slide end-pieces. The 3G apparently has addressed major issues of setup identified in the previous stage and been proven to be eligible to be further pursued in this project. On the other hand, the purchase of universal testing machine or Bose dual LM2 TB was completed and the testing system was delivered to ORNL in August 2012. The preliminary confirmation of the system and on-site training were given by Bose field engineer and regional manager on 8/1-8/2/2012. The calibration of Bose testing system has been performed by ORNL because the integration of ORNL setup into the Bose TestBench occurred after the installation. Major challenge with this process arose from two aspects: 1) the load control involves two load cells, and 2) U-frame setup itself is a non-standard specimen. ORNL has been able to implement the load control through Cycle Indirect along with pinning the U-frame setup. Two meetings with ORNL hot-cell group (November 2012 and January 2013) were held to discuss the potential issues with both epoxy mounting of rigid sleeve and U-frame setup. Many suggestions were provided to make the procedure friendlier to the manipulator in hot cell. Addressing of these suggestions resulted in another cycle of modifications of both vise mold and setup. The initial meeting with ORNL I&C group occurred in November 2012 with regard to the Bose cable modification and design of central panel to integrate the cables and wires. The first round of cable modification and central panel fabrication was completed in February 2012. The testing with the modified cables exhibited substantial noises and the testing system was not shown to be stable. It was believed the cross talk was responsible to the noise, and a central panel with a better grounding and shielding was highly recommended. The central panel has been re-designed and fabricated in March 2013. In the subsequent period, the ORNL made substantial effort to debug the noises with the load cell channel, and to resolve the noises and nonlinearity with RDP LVDTs related to the integration of RDP LVDTs to Bose system. At the same time, ORNL has completed the verification tests of Bose test system, including cycle tests under reversal bending in load control, bending tests under monotonic load, and cycle tests under reversal bending in load control on MTS machine to verify the results of Bose machine. These results are shown to be consistent under equivalent loading conditions, especially for the cycle tests. Rad hardened LVDTs will be incorporated into the Bose system once received, and 10 Hz tests will be completed in the next step. The schedule for the final check of the Bose system is being finalized before the system delivered to the hot cell.

  10. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: FOA Type Term Title Author Replies Last Post sort icon Blog entry FOA...

  11. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: EIA Type Term Title Author Replies Last Post sort icon Blog entry EIA...

  12. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer Home > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: API Type Term Title Author Replies Last Post sort icon Blog entry API...

  13. Ripeness sensor development

    SciTech Connect (OSTI)

    Not Available

    1992-11-01

    About 20--25% of the total production of fruits and vegetables in the USA must be discarded after harvest About 25--30% of this loss is the result of over-ripening and this loss represents about 8.39 [times] 10[sup 12] BTU of invested energy every year. This invested energy could be saved by non-destructive ripeness sensing. Sweetness is an important indicator of fruit quality and highly correlated with ripeness in most fruits. Research to develop a non-destructive fruit ripeness sensor has been conducted in the Agricultural Engineering Department at Purdue University. It is based on [sup 1]H-MR (proton Magnetic Resonance). A first generation prototype of the ripeness sensor based on [sup 1]H-MR was built and tested with. Results show that the sensor can discriminate small fruit (0.75 in diameter or smaller) differing in sugar content by 6%. This prototype can separate the fruit into at least two groups: one ripe and the other not ripe. The estimated cost for such a ripeness sensor is around $4,000. The signal sensitivity of the prototype can be improved to enable it to differentiate between fruits varying in sugar content by only 1 or 2% by using water peak suppression techniques to recover relatively weak sugar resonance signals in intact fruits, modifying circuits to eliminate noise, leakage and distortion of input/output signals, improving the magnetic console to get a higher magnetic field and better homogeneity, and designing a probe to achieve a higher signal-to-noise (S/N) ratio. As research continues a second generation ripeness sensor will be developed which will incorporate many of the improvements and which will be suitable for commercial use. Additional research will allow application of the technique to a wider range of fruit sizes (from blueberries to watermelons). This report describes estimated energy savings, feasibility studies, development of the initial prototype, and preliminary evaluation of the first generation prototype.

  14. Advanced servomanipulator development

    SciTech Connect (OSTI)

    Kuban, D.P.

    1985-01-01

    The Advanced Servomanipulator (ASM) System consists of three major components: the ASM slave, the dual arm master controller (DAMC) or master, and the control system. The ASM is remotely maintainable force-reflecting servomanipulator developed at the Oak Ridge National Laboratory (ORNL) as part of the Consolidated Fuel Reprocessing Program. This new manipulator addresses requirements of advanced nuclear fuel reprocessing with emphasis on force reflection, remote maintainability, reliability, radiation tolerance, and corrosion resistance. The advanced servomanipulator is uniquely subdivided into remotely replaceable modules which will permit in situ manipulator repair by spare module replacement. Manipulator modularization and increased reliability are accomplished through a force transmission system that uses gears and torque tubes. Digital control algorithms and mechanical precision are used to offset the increased backlash, friction, and inertia resulting from the gear drives. This results in the first remotely maintainable force-reflecting servomanipulator in the world.

  15. Alloys in energy development

    SciTech Connect (OSTI)

    Frost, B.R.T.

    1984-02-01

    The development of new and advanced energy systems often requires the tailoring of new alloys or alloy combinations to meet the novel and often stringent requirements of those systems. Longer life at higher temperatures and stresses in aggressive environments is the most common goal. Alloy theory helps in achieving this goal by suggesting uses of multiphase systems and intermediate phases, where solid solutions were traditionally used. However, the use of materials under non-equilibrium conditions is now quite common - as with rapidly solidified metals - and the application of alloy theory must be modified accordingly. Under certain conditions, as in a reactor core, the rate of approach to equilibrium will be modified; sometimes a quasi-equilibrium is established. Thus an alloy may exhibit enhanced general diffusion at the same time as precipitate particles are being dispersed and solute atoms are being carried to vacancy sinks. We are approaching an understanding of these processes and can begin to model these complex systems.

  16. Nawitas Development | Open Energy Information

    Open Energy Info (EERE)

    Development Jump to: navigation, search Name: Nawitas Development Place: Bratislava, Slovakia Zip: 831 06 Sector: Wind energy Product: Slovak based company active in wind energy...

  17. Industry Cluster Development Grant winners

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Industry Cluster Development Grant winners Community Connections: Your link to news and ... All Issues submit Industry Cluster Development Grant winners Recipients include Picuris ...

  18. Infrastructure Development and Financial Analysis

    Broader source: Energy.gov [DOE]

    Infrastructure Development and Financial Analysis quantifies the total costs of scenarios for developing the hydrogen infrastructure, including production, delivery, and utilization. By combining...

  19. NREL: Photovoltaics Research - Standards Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Standards Development NREL's Photovoltaic (PV) Engineering group supports the development of national and international standards for PV engineering. Current standards lack...

  20. Developer | OpenEI Community

    Open Energy Info (EERE)

    Developer header Developer Home > Groups Content Group Activity By term Q & A Feeds Share your own status updates, and follow the updates & activities of others by creating your...

  1. Power Systems Development Facility

    SciTech Connect (OSTI)

    2003-07-01

    This report discusses Test Campaign TC12 of the Kellogg Brown & Root, Inc. (KBR) Transport Gasifier train with a Siemens Westinghouse Power Corporation (SW) particle filter system at the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama. The Transport Gasifier is an advanced circulating fluidized-bed reactor designed to operate as either a combustor or a gasifier using a particulate control device (PCD). While operating as a gasifier, either air or oxygen can be used as the oxidant. Test run TC12 began on May 16, 2003, with the startup of the main air compressor and the lighting of the gasifier start-up burner. The Transport Gasifier operated until May 24, 2003, when a scheduled outage occurred to allow maintenance crews to install the fuel cell test unit and modify the gas clean-up system. On June 18, 2003, the test run resumed when operations relit the start-up burner, and testing continued until the scheduled end of the run on July 14, 2003. TC12 had a total of 733 hours using Powder River Basin (PRB) subbituminous coal. Over the course of the entire test run, gasifier temperatures varied between 1,675 and 1,850 F at pressures from 130 to 210 psig.

  2. Development and turbine engine performance of three advanced rhenium containing superalloys for single crystal and directionally solidified blades and vanes

    SciTech Connect (OSTI)

    Broomfield, R.W.; Ford, D.A.; Bhangu, J.K.; Thomas, M.C.; Frasier, D.J.; Burkholder, P.S.; Harris, K.; Erickson, G.L.; Wahl, J.B.

    1998-07-01

    Turbine inlet temperatures over the next few years will approach 1,650 C (3,000 F) at maximum power for the latest large commercial turbofan engines, resulting in high fuel efficiency and thrust levels approaching 445 kN (100,000 lbs). High reliability and durability must be intrinsically designed into these turbine engines to meet operating economic targets and ETOPS certification requirements. This level of performance has been brought about by a combination of advances in air cooling for turbine blades and vanes, design technology for stresses and airflow, single crystal and directionally solidified casting process improvements, and the development and use of rhenium (Re) containing high {gamma}{prime} volume fraction nickel-base superalloys with advanced coatings, including full-airfoil ceramic thermal barrier coatings. Re additions to cast airfoil superalloys not only improves creep and thermo-mechanical fatigue strength, but also environmental properties including coating performance. Re dramatically slows down diffusion in these alloys at high operating temperatures. A team approach has been used to develop a family of two nickel-base single crystal alloys (CMSX-4 containing 3% Re and CMSX-10 containing 6% Re) and a directionally solidified, columnar grain nickel-base alloy (CM 186 LC containing 3% Re) for a variety of turbine engine applications. A range of critical properties of these alloys is reviewed in relation to turbine component engineering performance through engine certification testing and service experience. Industrial turbines are now commencing to use this aero developed turbine technology in both small and large frame units in addition to aero-derivative industrial engines. These applications are demanding, with high reliability required for turbine airfoils out to 25,000 hours, with perhaps greater than 50% of the time spent at maximum power. Combined cycle efficiencies of large frame industrial engines are scheduled to reach 60% in the US ATS program. Application experience to a total 1.3 million engine hours and 28,000 hours individual blade set service for CMSX-4 first stage turbine blades is reviewed for a small frame industrial engine.

  3. Process Development for Nanostructured Photovoltaics

    Broader source: Energy.gov [DOE]

    Fact Sheet About Low-Cost Nanofabrication Method To Develop Nanostructured, Dye-Sensitized Solar Cells

  4. 1998 wire development workshop proceedings

    SciTech Connect (OSTI)

    1998-04-01

    This report consists of vugraphs of the presentations at the conference. The conference was divided into the following sessions: (1) First Generation Wire Development: Status and Issues; (2) First Generation Wire in Pre-Commercial Prototypes; (3) Second Generation Wire Development: Private Sector Progress and Issues; (4) Second Generation Wire Development: Federal Laboratories; and (5) Fundamental Research Issues for HTS Wire Development.

  5. Breakthrough Vehicle Development - Fuel Cells

    Fuel Cell Technologies Publication and Product Library (EERE)

    Document describing research and development program for fuel cell power systems for transportation applications.

  6. Process Development for Nanostructured Photovoltaics

    SciTech Connect (OSTI)

    2011-05-31

    Fact sheet describing low-cost nanofabrication method to develop nanostructured, dye-sensitized solar cells

  7. WEC Model Development at Sandia

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2C Marine and Hydrokinetic Instrumentation, Measurement & Computer Modeling Workshop - Broomfield, CO July 9 th , 2012 Wave Energy Converter Model Development at Sandia Outline  Overview of SNL's WEC Modeling Activities * Wave Energy Development Roadmap * MHK Reference Models - Diana Bull * WEC Model Tool Development - Kelley Ruehl Reference Models and SNL Array Modeling presented in next session Wave Energy Development Roadmap Overall Goal and Motivation  Goal: Develop a suggested

  8. Energy Department Develops Roadmap to Help Spur Geothermal Energy Development

    Broader source: Energy.gov [DOE]

    Geothermal Regulatory Roadmap will help developers navigate regulatory requirements at every level of government to deploy geothermal energy projects.

  9. IEED Tribal Energy Development to Build Tribal Energy Development Capacity

    Broader source: Energy.gov [DOE]

    The Assistant Secretary - Indian Affairs for the U.S. Department of the Interior, through the Office of Indian Energy and Economic Development, is soliciting grant proposals from Indian tribes to build tribal capacity for energy resource development or management under the Department of the Interior's (DOl's) Tribal Energy Development Capacity (TEDC) grant program.

  10. Recent Developments in SHERPA

    SciTech Connect (OSTI)

    Archibald, Jennifer; Gleisberg, Tanju; Hoeche, Stefan; Krauss, Frank; Schonherr, Marek; Schumann, Steffen; Siegert, Frank; Winter, Jan; /Fermilab

    2011-11-15

    Some recent QCD-related developments in the SHERPA event generator are presented. In the past decades, event generators such as PYTHIA [1, 2] and HERWIG [3, 4] have been central for nearly all physics analyses at particle physics experiments at the high-energy frontier. This will also hold true at the LHC, where a large number of interesting signals for new particles or new phenomena (the Higgs boson or any other manifestation of the mechanism behind electro-weak symmetry breaking, supersymmetry, extra dimensions etc.) is hampered by a plethora of severe, sometimes overwhelming backgrounds. Nearly all of them are largely influenced by QCD. Therefore it seems fair to say that the success of the LHC in finding new physics may very well depend on a deep and detailed understanding of old physics, like QCD. Examples for this include, among others, the central-jet veto for the vector boson fusion channel for Higgs production or topologies, where gauge bosons emerge in association with many jets, a background for many search channels. In a reflection on increased needs by the experimental community, aiming at higher precision, incorporation of new physics models and so on, the work horses of old have undergone serious renovation efforts, resulting in new, improved versions of the respective codes, namely PYTHIA8 [5] and HERWIG++ [6]. In addition a completely new code, SHERPA [7], has been constructed and is in the process of maturing. The status of this code is the topic of this contribution. SHERPA's hallmark property is the inclusion of higher-order tree-level QCD contributions, leading to an improved modelling of jet production. They are introduced through a full-fledged matrix element generator, AMEGIC++ [8], which is capable of generating matrix elements and corresponding phase space mappings for processes with multi-particle final states in various models, including the Standard Model, anomalous gauge triple and quadruple couplings according to [9, 10], the Minimal Supersymmetric Standard Model with Feynman rules from [11], the ADD-model of extra dimensions [12, 13], and a model with an extra U(1) singlet coupling to the Higgs boson only [14]. The code has been thoroughly tested and validated [15]. This code, however, is limited, especially in the treatment of many ({ge} 6) external QCD particles. Therefore, in the near future, SHERPA will incorporate another, new matrix element generator, COMIX, which is based on Berends-Giele recursion relations [16] and color-dressing [17] rather than color-ordering. In Tabs. 1 and 2 some example cross sections for gg {yields} ng at fixed energies and pp {yields} b{bar b} + n jets obtained with this program are exhibited and compared to those from other programs. In addition, concerning the calculation of higher-order matrix elements and cross sections, there have been first steps towards an automation of such calculations at truly next-to leading order accuracy. They manifest themselves in the implementation of a procedure [19] to fully automatically construct and evaluate Catani-Seymour dipole subtraction terms [20] for the real part of such NLO calculations. The results from the matrix element calculations are merged with the subsequent parton shower through the formalism of [21, 22]. The results of its implementation in SHERPA [23] has recently been compared with other algorithms [24]. Although there remains some dispute about the theoretical equivalence of the different approaches, the overall results show satisfying agreement with each other, such that they can be used with confidence for data analysis.

  11. Developer | OpenEI Community

    Open Energy Info (EERE)

    > Developer > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: Big Data Type Term Title Author Replies Last Post sort icon Blog entry Big Data Visualize...

  12. Developer | OpenEI Community

    Open Energy Info (EERE)

    New Result Formats on OpenEI Jweers 25 Mar 2013 - 12:22 Blog entry developer OpenEI maintenance March 8-9, 2013 Rmckeel 8 Mar 2013 - 14:23 Blog entry developer Semantic Mediawiki...

  13. Development of MP3 Technologies

    Office of Scientific and Technical Information (OSTI)

    Development of MP3 Technologies Impact of Basic Research on Innovation - Edited excerpts from American Competitiveness Initiative, February 2006

  14. Developing Substitutes | Critical Materials Institute

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Developer Resources Developer Resources Apps for Energy Apps for Energy The Energy Department is challenging developers to use the Green Button data access program to bring residential and commercial utility data to life with fun and creative apps. Read more Learn about Green Button Learn about Green Button Apps for Energy submissions must use Green Button data. To learn more, start here. Read more NREL Resources NREL Resources NREL offers a number resources for Green Button app developers. Find

  15. Developer Resources | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Developer Resources Developer Resources Apps for Energy Apps for Energy The Energy Department is challenging developers to use the Green Button data access program to bring residential and commercial utility data to life with fun and creative apps. Read more Learn about Green Button Learn about Green Button Apps for Energy submissions must use Green Button data. To learn more, start here. Read more NREL Resources NREL Resources NREL offers a number resources for Green Button app developers. Find

  16. Technology Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Development Technology Development OE supports a portfolio of technology development and deployment programs that will modernize our Nation's electric delivery system. To be successful, it is essential that key stakeholders be involved in this enterprise, including federal and state government agencies, electric power companies, equipment manufacturers, systems developers, and consumers, and work together toward a shared vision of the future, with full understanding of each other's respective

  17. Development of MP3 Technologies

    Office of Scientific and Technical Information (OSTI)

    Development of MP3 Technologies Impact of Basic Research on Innovation - Edited excerpts from American Competitiveness Initiative, February 2006...

  18. NREL: Process Development and Integration Laboratory - Process Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Integration Design Features Process Development and Integration Design Features The cluster tool and transport pod are at the heart of the research approach used within the Process Development and Integration Laboratory. In developing this approach, scientists in the National Center for Photovoltaics worked closely with their industry counterparts to design a system with maximum functionality and flexibility. In this section, we refer to the schematic below to illustrate a process

  19. Energy Department Develops Regulatory Roadmap to Spur Geothermal Energy Development

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Energy Department today issued a Geothermal Regulatory Roadmap that will help developers navigate regulatory requirements at every level of government to deploy geothermal energy projects.

  20. Renewable Energy Project Development and Finance: Advanced Development...

    Energy Savers [EERE]

    was created to give tribal leaders and professionals background information in renewable energy development to: Present foundational information on strategic energy planning, ...

  1. Stage 3c: Developing and Assessing Low Emissions Development...

    Open Energy Info (EERE)

    Low Emissions Development Scenarios Jump to: navigation, search Stage 3 LEDS Home Introduction to Framework Assess current country plans, policies, practices, and capacities...

  2. Community-Driven Development Decision Tools for Rural Development...

    Open Energy Info (EERE)

    (CDD) investment programmes as a way to further enabling rural poor people to overcome poverty in WCA." References "Community-Driven Development Decision Tools" Retrieved from...

  3. Sustainable Urban Development Priorities - Development of a Rapid...

    Open Energy Info (EERE)

    investments, transport interventions and policies, and will be developed with the involvement of the stakeholders to identify existing mobility patterns and deficiencies....

  4. OpenEIS. Developer Guide

    SciTech Connect (OSTI)

    Lutes, Robert G.; Neubauer, Casey C.; Haack, Jereme N.; Carpenter, Brandon J.; Monson, Kyle E.; Allwardt, Craig H.; Sharma, Poorva; Akyol, Bora A.

    2015-03-31

    The Department of Energy’s (DOE’s) Building Technologies Office (BTO) is supporting the development of an open-source software tool for analyzing building energy and operational data: OpenEIS (open energy information system). This tool addresses the problems of both owners of building data and developers of tools to analyze this data. Building owners and managers have data but lack the tools to analyze it while tool developers lack data in a common format to ease development of reusable data analysis tools. This document is intended for developers of applications and explains the mechanisms for building analysis applications, accessing data, and displaying data using a visualization from the included library. A brief introduction to the visualizations can be used as a jumping off point for developers familiar with JavaScript to produce their own. Several example applications are included which can be used along with this document to implement algorithms for performing energy data analysis.

  5. Marine and Hydrokinetic Energy Research & Development | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research & Development Marine and Hydrokinetic Energy Research & Development Marine and Hydrokinetic Energy Research & Development Marine and Hydrokinetic Energy Research &...

  6. Systems and Professional Development - David Brown, Director...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Systems and Professional Development - David Brown, Director, Systems & Professional Development, OAPM Systems and Professional Development - David Brown, Director, Systems & ...

  7. Direct Research & Development Transactions | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Direct Research & Development Transactions Direct Research & Development Transactions DOE direct research and development transactions include contracts, grants, and cooperative ...

  8. Ethiopian Development Research Institute | Open Energy Information

    Open Energy Info (EERE)

    Ethiopian Development Research Institute Jump to: navigation, search Logo: Ethiopian Development Research Institute Name: Ethiopian Development Research Institute Address: Ethiopia...

  9. Project Management Career Development Program | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    are here Home Operational Management Certifications and Professional Development Project Management Career Development Program Project Management Career Development...

  10. Pompano subsea development -- Testing program

    SciTech Connect (OSTI)

    Nelson, R.; Berger, R.; Tyer, C.

    1996-12-31

    System reliability is essential for the economic success of any subsea oil and gas development. Testing programs can be developed to prove system reliability while still adhering to cost and schedule constraints. This paper describes a three-tiered equipment testing program that was employed for the Pompano Phase 2 subsea system. Program objectives, test descriptions, procedure development and test execution are discussed in detail. Lessons learned throughout the tests are also presented.

  11. NREL: Technology Deployment - Project Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Project Development By employing our project development models, NREL offers a broad range of advisory services that are based off commercial practices and support the entire project development process to help reduce the risks associated with energy efficiency and renewable energy projects. This includes policy and regulatory analysis, financing alternatives, project management, proposal reviews, and project risk and technology assessments. Policy and Regulatory Analysis NREL analyzes federal

  12. WINDExchange: Education and Workforce Development

    Wind Powering America (EERE)

    Education Printable Version Bookmark and Share Workforce Development Collegiate Wind Competition Wind for Schools Project School Project Locations Education & Training Programs Curricula & Teaching Materials Resources Education and Workforce Development WINDExchange offers resources for anyone wishing to learn about wind energy at any level. Learn about workforce development initiatives, including the U.S. Department of Energy Collegiate Wind Competition, the Wind for Schools project,

  13. New Program Development & Launch

    U.S. Energy Information Administration (EIA) Indexed Site

    Program Development & Launch visit: on.sce.com/ideas Mark Podorsky Principal Manager; Implementation & Information Governance Southern California Edison New Program Development & Launch visit: on.sce.com/ideas Southern California Edison An Edison International Company - Serving Customers for 125 Years Serves a population of more than 14 million people in a 50,000 square mile area of Central, Coastal, and Southern California Southern California Edison 2 New Program Development &

  14. ORISE: Instructional Design and Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Instructional Design and Development The Oak Ridge Institute for Science and Education (ORISE) works with government agencies and organizations to create customized training and instructional design programs, from traditional classroom teaching to online education. ORISE uses a multi-step process to define the instructional design and development needs. Our process includes: Defining the target audience and objectives Designing and developing the program and materials Piloting, delivering and

  15. MPAS-Ocean Development Update

    SciTech Connect (OSTI)

    Jacobsen, Douglas W.; Ringler, Todd D.; Petersen, Mark R.; Jones, Philip W.; Maltrud, Mathew E.

    2012-06-13

    The Model for Prediction Across Scales (MPAS) is a modeling framework developed jointly between NCAR and LANL, built to allow core developers to: rapidly develop new dynamical cores, and leverage improvements made to shared codes. MPAS-Ocean (MPAS-O) is a functioning ocean model capable of high resolution, or highly vairable resolution simulations. The first MPAS-O publication is expected by the end of the year.

  16. Policy Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Policy Development Policy Development Policy Development Project Management Policy and Systems (PM-30) is working to update all Project Management related orders, guides, handbooks, and standard operating procedures that the Office of Project Management Oversight and Assessments (PM) has published. The primary focus of the updates are to insure that the orders and guides, handbooks and SOPs reflect the latest guidance that the Secretary of the Energy has outlined in his memorandum dated December

  17. Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for Magnetic Self-Organization in Laboratory and Astrophysical Plasmas, NSF, 4201 Wilson Boulevard, Arlington, Virginia 22230 J. K. Anderson Department of Physics, University ...

  18. Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    OF IMAGING We require: (1) a high quality ion beam, (2) computer vision and image processing techniques for isolating and re- constructing the beam, and (3) wavelengths suitable...

  19. Blackfeet Nation - Energy Organization Development

    Energy Savers [EERE]

    Organization Development First Steps to Renewable Energy Grant Awarded by Department of Energy ... CO) (Lakewood, CO) Whiteing & Smith Law, Whiteing & Smith Law, Jeanne Whiteing ...

  20. Laboratory Directed Research and Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Phone Book Jobs Laboratory Directorate - Strategic Planning Office Laboratory Directed Research and Development (LDRD) LBNL LDRD Program Guidelines LDRD FY 2017 Call for...

  1. Developer | OpenEI Community

    Open Energy Info (EERE)

    > Posts by term > Developer Content Group Activity By term Q & A Feeds Term: American Clean Skies Foundation Type Term Title Author Replies Last Post sort icon Blog entry...

  2. Development & Deployment: Kumeyaay Wind II

    Office of Environmental Management (EM)

    ... authorized by General Council to begin negotiation of Non-Disclosure Agreement (NDA) and Memorandum of Understanding (MOU) with selected developer - Consulting team and ...

  3. Leadership Development | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    by UChicago Argonne, LLC, develops future leaders at Argonne. Each year, the Laboratory Director selects 15 employees to participate in the program along with staff from Fermi...

  4. Winn Development | Open Energy Information

    Open Energy Info (EERE)

    with NREL Yes Partnership Type Test & Evaluation Partner Partnering Center within NREL Electricity Resources & Building Systems Integration Winn Development is a company located...

  5. Geothermal Research and Development Programs

    Broader source: Energy.gov [DOE]

    Here you'll find links to laboratories, universities, and colleges conducting research and development (R&D) in geothermal energy technologies.

  6. Laboratory Directed Research and Development

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    To establish Department of Energy (DOE) requirements for laboratory directed research and development (LDRD) while providing the laboratory director broad flexibility for program implementation.

  7. Renewable Natural Gas- Developer Perspective

    Broader source: Energy.gov [DOE]

    Breakout Session 3-C: Renewable Gaseous FuelsRenewable Natural Gas - Developer PerspectiveDavid Ross, Managing Director, MultiGen International, LLC

  8. NOxsensor development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    development PDF icon pm005woo2010o.pdf More Documents & Publications Electrochemical NOx Sensors for Monitoring Diesel Emissions Electrochemical NOxSensor for Monitoring Diesel...

  9. Advanced LWR Nuclear Fuel Development

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Instrumentation, Information, and Control Systems ... and Scope * Develop the fundamental scientific basis to ... the plan to deliver on the vision of the pathway. * Strategy ...

  10. OpenEI Community - developer

    Open Energy Info (EERE)

    title"" >After several months of development and testing, the next generation web service for the utility rate database is finally here I encourage you to check out the...

  11. Laboratory Directed Research and Development

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2015-04-30

    To establish Department of Energy (DOE) requirements for laboratory directed research and development (LDRD) while providing the laboratory director broad flexibility for program implementation

  12. Carbon Capture Research and Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Center Lawrence Berkeley National Laboratory Research Institute of Innovative Energy Carbon Capture Research and Development Carbon capture and storage from fossil-based power...

  13. Laboratory Directed Research & Development (LDRD)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Laboratory Directed Research & Development National security depends on science and technology. The United States relies on Los Alamos National Laboratory for the best of...

  14. Developing Alaskan Sustainable Housing Training

    Broader source: Energy.gov [DOE]

    Hosted by the Association of Alaska Housing Authorities (AAHA), this three-day training event covers strategies and technical issues related to sustainable housing development.

  15. offshore wind research and development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    offshore wind research and development - Sandia Energy Energy Search Icon Sandia Home ... Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power ...

  16. DEVELOPMENT Solutions | Open Energy Information

    Open Energy Info (EERE)

    Product: DEVELOPMENT Solutions (DS) supports investors to realise projects with sustainable applications, including in the areas of environment, energy efficiency, water...

  17. DEVELOPMENT OF A SENSOR NETWORK TEST BED FOR ISD MATERIALS AND STRUCUTRAL CONDITION MONITORING

    SciTech Connect (OSTI)

    Zeigler, K.; Ferguson, B.; Karapatakis, D.; Herbst, C.; Stripling, C.

    2011-07-06

    The P Reactor at the Savannah River Site is one of the first reactor facilities in the US DOE complex that has been placed in its end state through in situ decommissioning (ISD). The ISD end state consists of a grout-filled concrete civil structure within the concrete frame of the original building. To evaluate the feasibility and utility of remote sensors to provide verification of ISD system conditions and performance characteristics, an ISD Sensor Network Test Bed has been designed and deployed at the Savannah River National Laboratory. The test bed addresses the DOE-EM Technology Need to develop a remote monitoring system to determine and verify ISD system performance. Commercial off-the-shelf sensors have been installed on concrete blocks taken from walls of the P Reactor Building. Deployment of this low-cost structural monitoring system provides hands-on experience with sensor networks. The initial sensor system consists of: (1) Groutable thermistors for temperature and moisture monitoring; (2) Strain gauges for crack growth monitoring; (3) Tiltmeters for settlement monitoring; and (4) A communication system for data collection. Preliminary baseline data and lessons learned from system design and installation and initial field testing will be utilized for future ISD sensor network development and deployment.

  18. Development of an X-ray pixel detector with multi-port charge-coupled device for X-ray free-electron laser experiments

    SciTech Connect (OSTI)

    Kameshima, Takashi; Ono, Shun; Kudo, Togo; Ozaki, Kyosuke; Kirihara, Yoichi; Kobayashi, Kazuo; Inubushi, Yuichi; Yabashi, Makina; Hatsui, Takaki; RIKEN SPring-8 Center, 1-1-1 Kouto, Sayo-cho, Sayo-gun, Hyogo 679-5148 ; Horigome, Toshio; Holland, Andrew; Holland, Karen; Burt, David; Murao, Hajime

    2014-03-15

    This paper presents development of an X-ray pixel detector with a multi-port charge-coupled device (MPCCD) for X-ray Free-Electron laser experiments. The fabrication process of the CCD was selected based on the X-ray radiation hardness against the estimated annual dose of 1.6 × 10{sup 14} photon/mm{sup 2}. The sensor device was optimized by maximizing the full well capacity as high as 5 Me- within 50 μm square pixels while keeping the single photon detection capability for X-ray photons higher than 6 keV and a readout speed of 60 frames/s. The system development also included a detector system for the MPCCD sensor. This paper summarizes the performance, calibration methods, and operation status.

  19. Recovery Act Workforce Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Act Workforce Development Recovery Act Workforce Development Map of Smart Grid Workforce Development Map of Smart Grid Workforce Development 19 Awards Read more Map of Workforce ...

  20. Risk perception in developing countries

    SciTech Connect (OSTI)

    Wilbanks, T.J.; Rayner, S.F.

    1985-02-15

    The paper briefly reviews: (1) what risk perception means to most people in developing countries; (2) some of the modern-technology-related risks to which people in these countries are exposed; and (3) some research evidence about risk perception that gives hints about how such perceptions will evolve in developing countries. (ACR)

  1. 2013 Nuclear Workforce Development Day

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nuclear Energy Impact Topics: Today's & Tomorrow's New Nuclear Energy Construction & the Workforce Outlook  Current New Nuclear Energy Construction Projects  Small Modular Reactor Developments  Nuclear Workforce Demo Moderator: Nora Swanson - Workforce Development Coordinator Southern Company Panel Members: Scott Macfarland - Manager, Corporate Workforce Planning SCANA Corporation Randy Johnson - Vice President, Operational Readiness Vogtle 3 &4 Southern Company Mary

  2. Advanced Emissions Control Development Program

    SciTech Connect (OSTI)

    A.P.Evans; K.E. Redinger; M.J. Holmes

    1998-04-01

    The objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of air toxics from coal-fired boilers. Ideally, the project aim is to effectively control air toxic emissions through the use of conventional flue gas cleanup equipment such as electrostatic precipitators (ESPS), fabric filters (baghouse), and wet flue gas desulfurization. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate and hydrogen chloride. Following the construction and evaluation of a representative air toxics test facility in Phase I, Phase II focused on the evaluation of mercury and several other air toxics emissions. The AECDP is jointly funded by the United States Department of Energy's Federal Energy Technology Center (DOE), the Ohio Coal Development Office within the Ohio Department of Development (oCDO), and Babcock& Wilcox-a McDermott company (B&W).

  3. NREL: Workforce Development and Education Programs - Workforce Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Education Programs News Workforce Development and Education Programs News Below are news stories involving NREL Workforce Development and Educations Programs. May 5, 2016 Energy Department Selects NREL Scientist for Exclusive Award Scientist Adele Tamboli of the Energy Department's (DOE) National Renewable Energy Laboratory (NREL) has been awarded additional funding as part of a select group of scientists in the early stage of their careers. May 3, 2016 NREL Scientists and Engineers

  4. NREL: Workforce Development and Education Programs - Workforce Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Education Programs Staff Workforce Development and Education Programs Staff Contact the Workforce Development and Education Programs staff for questions on internships, graduate programs, competitions, teacher programs, and education initiatives. Photo of a woman sitting on the floor, assembling a wind turbine in front of a fan. Energy Institute participants use KidWind wind turbine kits to accomplish tasks such as pumping water, lifting weights, and charging a capacitor. The Energy

  5. DOE/SC-ARM/TR-093 VAP Development: Initiation, Development,

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    93 VAP Development: Initiation, Development, Evaluation, and Release M Jensen S McFarlane S Collis J Monroe J Fast C Sivaraman C Flynn S Xie J Mather February 2011 DISCLAIMER This report was prepared as an account of work sponsored by the U.S. Government. Neither the United States nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus,

  6. North Dakota Energy Workforce Development

    SciTech Connect (OSTI)

    Carter, Drake

    2014-12-29

    Bismarck State College, along with its partners (Williston State College, Minot State University and Dickinson State University), received funding to help address the labor and social impacts of rapid oilfield development in the Williston Basin of western North Dakota. Funding was used to develop and support both credit and non-credit workforce training as well as four major symposia designed to inform and educate the public; enhance communication and sense of partnership among citizens, local community leaders and industry; and identify and plan to ameliorate negative impacts of oil field development.

  7. Mass spectrometry for biomarker development

    SciTech Connect (OSTI)

    Wu, Chaochao; Liu, Tao; Baker, Erin Shammel; Rodland, Karin D.; Smith, Richard D.

    2015-06-19

    Biomarkers potentially play a crucial role in early disease diagnosis, prognosis and targeted therapy. In the past decade, mass spectrometry based proteomics has become increasingly important in biomarker development due to large advances in technology and associated methods. This chapter mainly focuses on the application of broad (e.g. shotgun) proteomics in biomarker discovery and the utility of targeted proteomics in biomarker verification and validation. A range of mass spectrometry methodologies are discussed emphasizing their efficacy in the different stages in biomarker development, with a particular emphasis on blood biomarker development.

  8. Lower Sioux Wind Feasibility & Development

    SciTech Connect (OSTI)

    Minkel, Darin

    2012-04-01

    This report describes the process and findings of a Wind Energy Feasibility Study (Study) conducted by the Lower Sioux Indian Community (Community). The Community is evaluating the development of a wind energy project located on tribal land. The project scope was to analyze the critical issues in determining advantages and disadvantages of wind development within the Community. This analysis addresses both of the Community's wind energy development objectives: the single turbine project and the Commerical-scale multiple turbine project. The main tasks of the feasibility study are: land use and contraint analysis; wind resource evaluation; utility interconnection analysis; and project structure and economics.

  9. Pulse Wave Well Development Demonstration

    SciTech Connect (OSTI)

    Burdick, S.

    2001-02-23

    Conventional methods of well development at the Savannah River Site generate significant volumes of investigative derived waste (IDW) which must be treated and disposed of at a regulated Treatment, Storage, or Disposal (TSD) facility. Pulse Wave technology is a commercial method of well development utilizing bursts of high pressure gas to create strong pressure waves through the well screen zone, extending out into the formation surrounding the well. The patented process is intended to reduce well development time and the amount of IDW generated as well as to micro-fracture the formation to improve well capacity.

  10. Business Development Executive (BDE) Program

    SciTech Connect (OSTI)

    Rice, E.J. "Woody"; Frederick, W. James

    2005-12-05

    The IPST BDE (Institute of Paper Science and Technology Business Development Executive) program was initiated in 1997 to make the paper industry better aware of the new manufacturing technologies being developed at IPST for the U.S. pulp and paper industry's use. In April 2000, the BDE program management and the 20 BDEs, all retired senior level industry manufacturing and research executives, were asked by Ms. Denise Swink of OIT at DOE to take the added responsibility of bringing DOE developed energy conservation technology to the paper industry. This project was funded by a DOE grant of $950,000.

  11. Workforce development | Open Energy Information

    Open Energy Info (EERE)

    Workforce development Jump to: navigation, search This article is a stub. You can help OpenEI by expanding it. Retrieved from "http:en.openei.orgwindex.php?titleWorkforcedeve...

  12. Laboratory Directed Research and Development

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2015-10-22

    To establish Department of Energy (DOE) requirements for laboratory directed research and development (LDRD) while providing the laboratory director broad flexibility for program implementation. Supersedes DOE O 413.2B.

  13. National Laboratory Impacts and Developments

    Broader source: Energy.gov [DOE]

    The Technology-to-Market program supports U.S. Department of Energy (DOE) initiatives that make access to laboratory-developed technologies and capabilities easier and increase partnerships with the clean energy private sector.

  14. Laboratory Directed Research and Development

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-01-08

    To establish the Department's, including the NNSA's, requirements for laboratory-directed research and development (LDRD) while providing the laboratory director broad flexibility for program implementation. Cancels DOE O 413.2. Canceled by DOE O 413.2B.

  15. ENERGY RESEARCH AND DEVELOPMENT ADMINISTRATION

    Office of Legacy Management (LM)

    .' :h I : ' ENERGY RESEARCH AND DEVELOPMENT ADMINISTRATION WASHINGTON, D.C. 20545 October ... ThcNa andCo,activlties-,are.easily-understandable-in terms of high energy neutron ...

  16. Portable code development in C

    SciTech Connect (OSTI)

    Brown, S.A.

    1990-11-06

    With a new generation of high performance computers appearing around us on a time scale of months, a new challenge for developers of simulation codes is to write and maintain production codes that are both highly portable and maximally efficient. My contention is that C is the language that is both best suited to that goal and is widely available today. GLF is a new code written mainly in C which is intended to have all of the XRASER physics and run on any platform of interest. It demonstrates the power of the C paradigm for code developers and flexibility and ease of use for the users. Three fundamental problems are discussed: the C/UNIX development environment; the supporting tools and libraries which handle data and graphics portability issues; and the advantages of C in numerical simulation code development.

  17. Laboratory Directed Research and Development

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2006-04-19

    The Order establishes DOE requirements and responsibilities for laboratory directed research and development while providing laboratory directors with broad flexibility for program implementation. Cancels DOE O 413.2A. Admin Chg 1, 1-31-11.

  18. Wind Development on the Rosebud

    Office of Environmental Management (EM)

    Rosebud Sioux Indian Reservation Wind Development on the Rosebud Akicita Cikala 750 Kw turbine Owl Feather War Bonnet Wind Farm LLC, 30Mw North Antelope Project 190Mw Akicita ...

  19. Wind Development on the Rosebud

    Energy Savers [EERE]

    From the book, Black Elk speaks, 1932 Rosebud Sioux Indian Reservation Wind Development on the Rosebud D Akicita Cikala 750 Kw turbine Proposed Owl Feather War Bonnet Wind Farm, ...

  20. Laboratory directed research and development

    SciTech Connect (OSTI)

    Not Available

    1991-11-15

    The purposes of Argonne's Laboratory Directed Research and Development (LDRD) Program are to encourage the development of novel concepts, enhance the Laboratory's R D capabilities, and further the development of its strategic initiatives. Among the aims of the projects supported by the Program are establishment of engineering proof-of-principle''; development of an instrumental prototype, method, or system; or discovery in fundamental science. Several of these project are closely associated with major strategic thrusts of the Laboratory as described in Argonne's Five Year Institutional Plan, although the scientific implications of the achieved results extend well beyond Laboratory plans and objectives. The projects supported by the Program are distributed across the major programmatic areas at Argonne. Areas of emphasis are (1) advanced accelerator and detector technology, (2) x-ray techniques in biological and physical sciences, (3) advanced reactor technology, (4) materials science, computational science, biological sciences and environmental sciences. Individual reports summarizing the purpose, approach, and results of projects are presented.

  1. Industry Cluster Development Grant winners

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Industry Cluster Development Grant winners Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue:May 2016 all issues All Issues » submit Industry Cluster Development Grant winners Recipients include Picuris Pueblo and Rio Arriba County February 1, 2015 A new community mural on the Hunter Ford facility in Española celebrates the building's planned revitalization and the future location of the Northern New Mexico Food Hub. A new community

  2. NGNP Research and Development Status

    SciTech Connect (OSTI)

    David A. Petti

    2010-08-01

    At the inception of the Next Generation Nuclear Plant (NGNP) project, experts from the Department of Energy (DOE) national laboratories, gas reactor vendors, and universities collaborated to establish technology research and development (R&D) roadmaps. These roadmaps outlined the testing and computational development activities needed to qualify the materials and validate the modeling and simulation tools to be used in the design and safe operation of the NGNP, a helium-cooled, high temperature gas reactor (HTGR).

  3. Superconducting magnet development in Japan

    SciTech Connect (OSTI)

    Yasukochi, K.

    1983-05-01

    The present state of R and D works on the superconducting magnet and its applications in Japan are presented. On electrical rotating machines, 30 MVA superconducting synchronous rotary condenser (Mitsubishi and Fuji) and 50 MVA generator are under construction. Two ways of ship propulsion by superconducting magnets are developing. A superconducting magnetically levitated and linear motor propelled train ''MAGLEV'' was developed by the Japan National Railways (JNR). The superconducting magnet development for fusion is the most active field in Japan. The Cluster Test program has been demonstrated on a 10 T Nb/sub 3/Sn coil and the first coil of Large Coil Task in IEA collaboration has been constructed and the domestic test was completed in JAERI. These works are for the development of toroidal coils of the next generation tokamak machine. R and D works on superconducting ohmic heating coil are in progress in JAERI and ETL. The latter group has constructed 3.8 MJ pulsed coil. A high ramp rate of changing field in pulsed magnet, 200 T/s, has been tested successfully. High Energy Physics Laboratory (KEK) are conducting active works. The superconducting ..mu.. meson channel and ..pi.. meson channel have been constructed and are operating successfully. KEK has also a project of big accelerator named ''TRISTAN'', which is similar to ISABELLE project of BNL. Superconducting synchrotron magnets are developed for this project. The development of superconducting three thin wall solenoid has been started. One of them, CDF, is progressing under USA-Japan collaboration.

  4. Hualapai Tribal Utility Development Project

    SciTech Connect (OSTI)

    Hualapai Tribal Nation

    2008-05-25

    The first phase of the Hualapai Tribal Utility Development Project (Project) studied the feasibility of establishing a tribally operated utility to provide electric service to tribal customers at Grand Canyon West (see objective 1 below). The project was successful in completing the analysis of the energy production from the solar power systems at Grand Canyon West and developing a financial model, based on rates to be charged to Grand Canyon West customers connected to the solar systems, that would provide sufficient revenue for a Tribal Utility Authority to operate and maintain those systems. The objective to establish a central power grid over which the TUA would have authority and responsibility had to be modified because the construction schedule of GCW facilities, specifically the new air terminal, did not match up with the construction schedule for the solar power system. Therefore, two distributed systems were constructed instead of one central system with a high voltage distribution network. The Hualapai Tribal Council has not taken the action necessary to establish the Tribal Utility Authority that could be responsible for the electric service at GCW. The creation of a Tribal Utility Authority (TUA) was the subject of the second objective of the project. The second phase of the project examined the feasibility and strategy for establishing a tribal utility to serve the remainder of the Hualapai Reservation and the feasibility of including wind energy from a tribal wind generator in the energy resource portfolio of the tribal utility (see objective 2 below). It is currently unknown when the Tribal Council will consider the implementation of the results of the study. Objective 1 - Develop the basic organizational structure and operational strategy for a tribally controlled utility to operate at the Tribe’s tourism enterprise district, Grand Canyon West. Coordinate the development of the Tribal Utility structure with the development of the Grand Canyon West Power Project construction of the power infrastructure at Grand Canyon West. Develop the maintenance and operations capacity necessary to support utility operations. Develop rates for customers on the Grand Canyon West “mini-grid” sufficient for the tribal utility to be self-sustaining. Establish an implementation strategy for tribal utility service at Grand Canyon West Objective 2 - Develop a strategy for tribal utility takeover of electric service on the Reservation. Perform a cost analysis of Reservation electrical service. Develop an implementation strategy for tribal takeover of Reservation electrical service. Examine options and costs associated with integration of the Tribe’s wind resources.

  5. Electronic networking and sustainable development

    SciTech Connect (OSTI)

    Daudpota, Q.I.

    1995-12-01

    To increase the capacity of institutions in various countries to implement the ambitious plans of Agenda 21, the United Nations Development Programme (UNDP) set up the Sustainable Development Networking Programme (SDNP) to help the process of sustainable development nationally and globally. Started initially in 15 developing countries, SDNPs are considered as a medium for individuals, organizations and governments to communicate ideas, share information resources, and exchange experiences among each other and globally to learn the appropriate ways to solve our ecological problems. The paper will review the idea of SDNPs globally and will describe in detail its successful implementation in Pakistan. In a country with, hitherto, virtually no electronic mail service, the SDNP has shown how its provision has had a significant impact on obtaining useful information on environmental problems, and in one case has helped save lives. SDNP Pakistan has made an effort to demonstrate the benefits of electronic communications to wide range users in the country. Some of these will be described. It is suggested how electronic networks linking organizations and people in the developing world with experts, organizations and data sources internationally, can greatly assist developmental effort globally.

  6. HTS Wire Development Workshop: Proceedings

    SciTech Connect (OSTI)

    Not Available

    1994-07-01

    The 1994 High-Temperature Superconducting Wire Development Workshop was held on February 16--17 at the St. Petersburg Hilton and Towers in St. Petersburg, Florida. The meeting was hosted by Florida Power Corporation and sponsored by the US Department of Energy`s Superconductivity Program for Electric Power Systems. The meeting focused on recent high-temperature superconducting wire development activities in the Department of Energy`s Superconductivity Systems program. The meeting opened with a general discussion on the needs and benefits of superconductivity from a utility perspective, the US global competitiveness position, and an outlook on the overall prospects of wire development. The meeting then focused on four important technology areas: Wire characterization: issues and needs; technology for overcoming barriers: weak links and flux pinning; manufacturing issues for long wire lengths; and physical properties of HTS coils. Following in-depth presentations, working groups were formed in each technology area to discuss the most important current research and development issues. The working groups identified research areas that have the potential for greatly enhancing the wire development effort. These areas are discussed in the summary reports from each of the working groups. This document is a compilation of the workshop proceedings including all general session presentations and summary reports from the working groups.

  7. OSPREY Model Development Status Update

    SciTech Connect (OSTI)

    Veronica J Rutledge

    2014-04-01

    During the processing of used nuclear fuel, volatile radionuclides will be discharged to the atmosphere if no recovery processes are in place to limit their release. The volatile radionuclides of concern are 3H, 14C, 85Kr, and 129I. Methods are being developed, via adsorption and absorption unit operations, to capture these radionuclides. It is necessary to model these unit operations to aid in the evaluation of technologies and in the future development of an advanced used nuclear fuel processing plant. A collaboration between Fuel Cycle Research and Development Offgas Sigma Team member INL and a NEUP grant including ORNL, Syracuse University, and Georgia Institute of Technology has been formed to develop off gas models and support off gas research. Georgia Institute of Technology is developing fundamental level model to describe the equilibrium and kinetics of the adsorption process, which are to be integrated with OSPREY. This report discusses the progress made on expanding OSPREY to be multiple component and the integration of macroscale and microscale level models. Also included in this report is a brief OSPREY user guide.

  8. Advanced Emissions Control Development Program

    SciTech Connect (OSTI)

    A. P. Evans

    1998-12-03

    McDermott Technology, Inc. (MTI) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using the Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and the inorganic species, hydrogen chloride and hydrogen fluoride.

  9. Advanced Emission Control Development Program.

    SciTech Connect (OSTI)

    Evans, A.P.

    1997-12-31

    Babcock & Wilcox (B&W) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using B&W`s new Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and the inorganic species hydrogen chloride and hydrogen fluoride.

  10. Advanced Emissions Control Development Program

    SciTech Connect (OSTI)

    M. J. Holmes

    1998-12-03

    McDermott Technology, Inc. (MTI) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using the Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and hydrogen chloride and hydrogen fluoride.

  11. Advanced Emissions Control Development Program

    SciTech Connect (OSTI)

    A. P. Evans

    1998-12-03

    Babcock & Wilcox (B&W) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using B&W?s new Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and the inorganic species hydrogen chloride and hydrogen fluoride.

  12. Development of odd-Z-projectile reactions for transactinide element synthesis

    SciTech Connect (OSTI)

    Folden III, Charles Marvin

    2004-11-04

    The development of new odd-Z-projectile reactions leading to the production of transactinide elements is described. The cross section of the even-Z-projectile 208Pb(64Ni, n)271Ds reaction was measured at two new energies using the Berkeley Gas-filled Separator at the Lawrence Berkeley National Laboratory 88-Inch Cyclotron. In total, seven decay chains attributable to 271Ds were observed. These data, combined with previous results, establish an excitation function for the production of 271Ds. The maximum cross section was 20 +15 -11 pb at a center-of-target energy of 311.5 MeV in the laboratory frame.The data from the 271Ds experiments were used to estimate the optimum beam energy for the new odd-Z-projectile 208Pb(65Cu, n)272-111 reaction using the Fusion by Diffusion theory proposed by Swiatecki, Siwek-Wilczynska, and Wilczynski. A cross section for this reaction was measured for the first time, at a center-of-target energy of 321.1 MeV in the laboratory frame. The excitation energy f or compound nuclei formed at the target center was 13.2 MeV. One decay chain was observed, resulting in a measured cross section of 1.7 +3.9 -1.4 pb. This decay chain is in good agreement with previously published data on the decay of 272-111.The new odd-Z-projectile 208Pb(55Mn, n)262Bh reaction was studied at three different projectile energies, and 33 decay chains of 262Bh were observed. The existence of a previously reported alpha-decaying isomeric state in this nuclide was confirmed. Production of the ground state was preferred at all three beam energies. The maximum cross section was 540 +180 -150 pb at a projectile center-of-target energy of 264.0 MeV. This cross section is much larger than that previously reported for the even-Z-projectile 209Bi(54Cr, n)262Bh reaction, which may be because the 54Cr projectile energies in the latter reaction were too high for optimum production of the 1n product. At the highest projectile energy of 268.0 MeV in the target center, two decay chains from 261Bh were observed as a result of the 208Pb(55Mn, 2n) reaction. In summary, this work shows that odd-Z-projectile reactions can have cross sections comparable to analogous even-Z-projectile reactions, and that the energy of the maximum cross section for 1n reactions can be estimated simply.

  13. 56th and Walnut: A Philly Gut Rehab Development; Philadelphia, Pennsylvania (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2013-11-01

    Load-bearing brick-masonry multifamily buildings are prevalent in urban areas across much of the Northeast and mid-Atlantic. In most instances, these buildings are un-insulated unless they have been renovated within the past two decades. Affordable housing capital budgets typically limit what can be spent and energy improvements often take a back seat to basic capital improvements such as interior finish upgrades and basic repairs. The Consortium for Advanced Residential Buildings (CARB) is researching cost effective solution packages for significant energy efficiency and indoor air-quality improvements in these urban buildings. To explore how these low-cost retrofits can effectively integrate energy efficiency upgrades, CARB partnered with Columbus Property Management and Development, Inc. on a community-scale gut rehabilitation project located at 56th Street and Walnut Street in Philadelphia, consisting of 32 units in eleven 3-story buildings. These buildings were built in the early 1900s using stone foundations and solid brick-masonry walls. They were renovated in the 1990s to have interior light gauge metal framing with R-13 batt in the above-grade walls, induced-draft furnaces, and central air conditioning.

  14. Research, Development, Test, and Evaluation | National Nuclear...

    National Nuclear Security Administration (NNSA)

    About Our Programs Defense Programs Research, Development, Test, and Evaluation ... The Office of Research, Development, Test, and Evaluation directs research, development, ...

  15. Maan Development Company | Open Energy Information

    Open Energy Info (EERE)

    Company Jump to: navigation, search Name: Maan Development Company Place: Anman, Jordan Zip: 11195 Sector: Solar Product: Jordan-based developer of the Maan Development Area...

  16. Technological Research and Development Authority (TRDA) | Open...

    Open Energy Info (EERE)

    Research and Development Authority (TRDA) Jump to: navigation, search Logo: Technological Research and Development Authority (TRDA) Name: Technological Research and Development...

  17. Silicon Border Development LLC | Open Energy Information

    Open Energy Info (EERE)

    Silicon Border Development LLC Jump to: navigation, search Name: Silicon Border Development LLC Place: Poway, California Zip: 92064 Sector: Solar Product: US-based developer of...

  18. China Solar Tower Development | Open Energy Information

    Open Energy Info (EERE)

    Tower Development Jump to: navigation, search Name: China Solar Tower Development Place: China Sector: Solar Product: Joint venture for development of solar towers in China,...

  19. Ewing Land Development Services | Open Energy Information

    Open Energy Info (EERE)

    Ewing Land Development Services Jump to: navigation, search Name: Ewing Land Development & Services Place: Pella, Iowa Zip: 50219 Product: Real estate development company...

  20. Project Development and Finance | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Development and Finance Project Development and Finance Below are general resources for Tribes on energy project development and finance. Find additional resources on project ...

  1. Zero Waste Energy Development | Open Energy Information

    Open Energy Info (EERE)

    Energy Development Jump to: navigation, search Name: Zero Waste Energy Development Place: California Product: California-based partnership created to develop Zanker Road Biogas...

  2. EHN Green Energy Developments | Open Energy Information

    Open Energy Info (EERE)

    Developments Jump to: navigation, search Name: EHN Green Energy Developments Place: Spain Sector: Renewable Energy Product: Renewable energy development company, focusing on...

  3. LEESS Battery Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    LEESS Battery Development LEESS Battery Development 2012 DOE Hydrogen and Fuel Cells ... More Documents & Publications Development of Advanced Energy Storage Systems for High Power, ...

  4. Texas Water Development Board | Open Energy Information

    Open Energy Info (EERE)

    Development Board Jump to: navigation, search Logo: Texas Water Development Board Name: Texas Water Development Board Abbreviation: TWDB Address: 1700 North Congress Avenue Place:...

  5. EPCOR Power Development Corp | Open Energy Information

    Open Energy Info (EERE)

    Development Corp Jump to: navigation, search Name: EPCOR Power Development Corp Place: Canada Sector: Wind energy Product: Develops, constructs and operates non-regulated power...

  6. Overview of Geothermal Energy Development Webcast | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Overview of Geothermal Energy Development Webcast Overview of Geothermal Energy Development Webcast PDF icon GeothermalEnergyDevelopmentOverviewPresentation.pdf PDF icon ...

  7. Energy for Sustainable Development | Open Energy Information

    Open Energy Info (EERE)

    Development Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Energy for Sustainable Development AgencyCompany Organization: United Nations Development Programme, United...

  8. Historical development of the windmill

    SciTech Connect (OSTI)

    Shepherd, D.G.

    1990-12-01

    Throughout history, windmill technology represented the highest levels of development in those technical fields we now refer to as mechanical engineering, civil engineering, and aerodynamics. This report describes key stages in the technical development of windmills as prime movers -- from antiquity to construction of the well-known Smith-Putnam wind turbine generator of the 1940's, which laid the foundation for modern wind turbines. Subjects covered are windmills in ancient times; the vertical-axis Persian windmill; the horizontal-axis European windmill (including both post mills and tower mills); technology improvements in sails, controls, and analysis; the American farm windmill; the transition from windmills to wind turbines for generating electricity at the end of the 19th century; and wind turbine development in the first half of the 20th century. 43 refs.

  9. Plastic Laminate Pulsed Power Development

    SciTech Connect (OSTI)

    ALEXANDER,JEFF A.; SHOPE,STEVEN L.; PATE,RONALD C.; RINEHART,LARRY F.; JOJOLA,JOHN M.; RUEBUSH,MITCHELL H.; CROWE,WAYNE; LUNDSTROM,J.; SMITH,T.; ZAGAR,D.; PRESTWICH,K.

    2000-09-01

    The desire to move high-energy Pulsed Power systems from the laboratory to practical field systems requires the development of compact lightweight drivers. This paper concerns an effort to develop such a system based on a plastic laminate strip Blumlein as the final pulseshaping stage for a 600 kV, 50ns, 5-ohm driver. A lifetime and breakdown study conducted with small-area samples identified Kapton sheet impregnated with Propylene Carbonate as the best material combination of those evaluated. The program has successfully demonstrated techniques for folding large area systems into compact geometry's and vacuum impregnating the laminate in the folded systems. The major operational challenges encountered revolve around edge grading and low inductance, low impedance switching. The design iterations and lessons learned are discussed. A multistage prototype testing program has demonstrated 600kV operation on a short 6ns line. Full-scale prototypes are currently undergoing development and testing.

  10. Scanning probe microscopy competency development

    SciTech Connect (OSTI)

    Hawley, M.E.; Reagor, D.W.; Jia, Quan Xi

    1998-12-31

    This is the final report of a three-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). The project collaborators developed an ultra-high vacuum scanning tunneling microscope (UHV-STM) capability, integrated it with existing scanning probe microscopes, and developed new, advanced air-based scanning force techniques (SPMs). Programmatic, basic, and industrially related laboratory research requires the existence of SPMs, as well as expertise capable of providing local nano-scale information. The UHV-STM capability, equipped with load-lock system and several surface science techniques, will allow introduction, examination, and reaction of surfaces prepared under well-controlled vacuum conditions, including the examination of morphology and local bonding associated with the initial stages of film growth under controlled growth conditions. The resulting capabilities will enable the authors to respond to a variety of problems requiring local characterization of conducting and nonconducting surfaces in liquids, air, and UHV.

  11. Program development fund: FY 1987

    SciTech Connect (OSTI)

    Not Available

    1989-03-01

    It is the objective of the Fund to encourage innovative research to maintain the Laboratory's position at the forefront of science. Funds are used to explore new ideas and concepts that may potentially develop into new directions of research for the Laboratory and that are consistent with the major needs, overall goals, and mission of the Laboratory and the DOE. The types of projects eligible for support from PDF include: work in forefront areas of science and technology for the primary purpose of enriching Laboratory research and development capabilities; advanced study of new hypotheses, new experimental concepts, or innovative approaches to energy problems; experiments directed toward ''proof of principle'' or early determination of the utility of a new concept; and conception, design analyses, and development of experimental devices, instruments, or components. This report is a review of these research programs.

  12. Conceptual Frame Work of an Enhanced BPA BA (EBBA)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    fraction of the wind fleet scheduled on Committed Intra- Hour Schedules. CAISO intra-hour scheduling - BPA will encourage California BAs (and other NW BAs that do...

  13. Department of Energy Quadrennial Technology Review Framing Document

    Energy Savers [EERE]

    liquid or gaseous fuels is therefore another strategy to reduce oil consumption. The existing petroleum fleet is supported by an extensive infrastructure....

  14. EV Everywhere Framing Workshop - Report Out & Lessons Learned

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... driven" is still vague - EVs should not just be a replacement product, they need value added components eere.energy.gov Summary and Lessons Learned * Need to emphasize the need ...

  15. Department of Energy Quadrennial Technology Review Framing Document...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The DOE-QTR will provide a context and framework for the Department's energy programs, as well as principles by which to establish program plans with

  16. Department of Energy Quadrennial Technology Review Framing Document...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    A document entailling DOE-QTR and a context and framework for the Department's energy programs, as well as principles by which to establish program plans with

  17. NextGen Advanced Framing for High Performance Homes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Eliminates header Minimize jackking studs Features: Double rim member at openings Joist hangers at openings King studs carry gravity load and wind loading ...

  18. Molecular-Frame Angular Distributions of Resonant Auger Electrons

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    molecules and their interaction with electromagnetic radiation or charged particles, but ... MFADs of the h and i groups of the Auger spectrum for carbon monoxide molecules oriented ...

  19. The Importance of Internal Development

    SciTech Connect (OSTI)

    Gerst, Kacy; Moore, Randy A., Schaefer, Richard

    2015-02-10

    The story of an ARPA-E awardee doesn’t necessarily end when ARPA-E funding runs out. Two ARPA-E awardees—Eagle Picher Technologies and Baldor Electric Company—have developed technologies to the point where internal stakeholders of their respective companies committed additional funds to help these technologies achieve success in the market. This video features remarks from ARPA-E Technology-to-Market Advisor Kacy Gerst and interviews with technologists at Eagle Picher and Baldor, who each tell the story of how they achieved buy-in from their internal leadership to further develop their ARPA-E-funded technologies.

  20. Seneca Nation - Energy Organization Development

    Energy Savers [EERE]

    NATION Energy Organizational Development A "First Steps" Grant 11/1/08 - 12/31/08 SENECA NATION  In appreciation & Acknowledgment: - Seneca Nation Council  Arlene Bova, Llona LeRoy, Councilors & energy development Advocates - Dept. of Energy, Tribal Energy Program  First Steps Grant for Strategic Energy Planning  NREL - Anemometer Loan Program  First Steps Grant for Energy Organizational Planning - Dept. of Interior, Div. of Energy Resource & Mineral

  1. Solar photovoltaics for development applications

    SciTech Connect (OSTI)

    Shepperd, L.W.; Richards, E.H.

    1993-08-01

    This document introduces photovoltaic technology to individuals and groups specializing in development activities. Examples of actual installations illustrate the many services supplied by photovoltaic systems in development applications, including water pumping, lighting, health care, refrigeration, communications, and a variety of productive uses. The various aspects of the technology are explored to help potential users evaluate whether photovoltaics can assist them in achieving their organizational goals. Basic system design, financing techniques, and the importance of infrastructure are included, along with additional sources of information and major US photovoltaic system suppliers.

  2. Wind Energy Career Development Program

    SciTech Connect (OSTI)

    Gwen Andersen

    2012-03-29

    Saint Francis University has developed curriculum in engineering and in business that is meeting the needs of students and employers (Task 1) as well as integrating wind energy throughout the curriculum. Through a variety of approaches, the University engaged in public outreach and education that reached over 2,000 people annually (Task 2). We have demonstrated, through the success of these programs, that students are eager to prepare for emerging jobs in alternative energy, that employers are willing to assist in developing employees who understand the broader business and policy context of the industry, and that people want to learn about wind energy.

  3. Climate adaptation planning in practice: an evaluation of adaptation plans from three developed nations

    SciTech Connect (OSTI)

    Preston, Benjamin L; Westaway, Richard M.; Yuen, Emma J.

    2011-04-01

    Formal planning for climate change adaptation is emerging rapidly at a range of geo-political scales. This first generation of adaptation plans provides useful information regarding how institutions are framing the issue of adaptation and the range of processes that are recognized as being part of an adaptation response. To better understand adaptation planning among developed nations, a set of 57 adaptation plans from Australia, the United Kingdom and the United States was evaluated against a suite of 19 planning processes identified from existing guidance instruments for adaptation planning. Total scores among evaluated plans ranged from 16% of the maximum possible score to 61%, with an average of 37%. These results suggest adaptation plans are largely under-developed. Critical weaknesses in adaptation planning are related to limited consideration for non-climatic factors as well as neglect for issues of adaptive capacity including entitlements to various forms of capital needed for effective adaptation. Such gaps in planning suggest there are opportunities for institutions to make better use of existing guidance for adaptation planning and the need to consider the broader governance context in which adaptation will occur. In addition, the adaptation options prescribed by adaptation plans reflect a preferential bias toward low-risk capacity-building (72% of identified options) over the delivery of specific actions to reduce vulnerability. To the extent these findings are representative of the state of developed nation adaptation planning, there appear to be significant deficiencies in climate change preparedness, even among those nations often assumed to have the greatest adaptive capacity.

  4. Westinghouse thermal barrier coatings development

    SciTech Connect (OSTI)

    Goedjen, J.G.; Wagner, G.

    1995-10-01

    Westinghouse, in conjunction with the Department of Energy and Oak Ridge National Laboratory, has embarked upon a program for the development of advanced thermal barrier coatings for industrial gas turbines. Development of thermal barrier coatings (TBC`s) for industrial gas turbines has relied heavily on the transfer of technology from the aerospace industry. Significant differences in the time/temperature/stress duty cycles exist between these two coating applications. Coating systems which perform well in aerospace applications may not been optimized to meet power generation performance requirements. This program will focus on development of TBC`s to meet the specific needs of power generation applications. The program is directed at developing a state-of-the-art coating system with a minimum coating life of 25,000 hours at service temperatures required to meet increasing operating efficiency goals. Westinghouse has assembled a team of university and industry leaders to accomplish this goal. Westinghouse will coordinate the efforts of all program participants. Chromalloy Turbine Technologies, Inc. and Sermatech International, Inc. will be responsible for bond coat and TBC deposition technology. Praxair Specialty Powders, Inc. will be responsible for the fabrication of all bond coat and ceramic powders for the program. Southwest Research Institute will head the life prediction modelling effort; they will also be involved in coordinating nondestructive evaluation (NDE) efforts. Process modelling will be provided by the University of Arizona.

  5. Development of an ACP facility

    SciTech Connect (OSTI)

    Gil-Sung You; Won-Myung Choung; Jeong-Hoe Ku; il-Je Cho; Dong-Hak Kook; Kie-Chan Kwon; Eun-Pyo Lee; Ji-Sup Yoon; Seong-Won Park; Won-Kyung Lee

    2007-07-01

    KAERI has been developing an advanced spent fuel conditioning process (ACP). The ACP facility for a process demonstration consists of two air-sealed type hot cells. The safety analysis results showed that the facility was designed safely. The relevant integrated performance tests were also carried out successfully. (authors)

  6. Human factors in software development

    SciTech Connect (OSTI)

    Curtis, B.

    1986-01-01

    This book presents an overview of ergonomics/human factors in software development, recent research, and classic papers. Articles are drawn from the following areas of psychological research on programming: cognitive ergonomics, cognitive psychology, and psycholinguistics. Topics examined include: theoretical models of how programmers solve technical problems, the characteristics of programming languages, specification formats in behavioral research and psychological aspects of fault diagnosis.

  7. Laboratory Directed Research and Development

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2006-04-19

    The order establishes DOE requirements for laboratory directed research and development (LDRD) while providing the laboratory director broad flexibility for program implementation. Cancels DOE O 413.3A. Admin Chg 1, dated 1-31-11, cancels DOE O 413.2B. Certified 7-14-2011.

  8. 2013 Nuclear Workforce Development Day

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Career Workshop Topics:  Focusing on Your Strengths  Dressing for Success  Taking Advantage of Internships & Co-Op Programs Moderator: Renee Stewart - National Nuclear Security Administration Operations & Programs Savannah River Nuclear Solutions Panel Members: Nora Swanson - Workforce Development Coordinator Southern Company Andrew Bouldin - Workforce Strategies Team Leader Southern Company Scott Macfarland - Manager, Corporate Workforce Planning SCANA Corporation Career

  9. Renewable Energy Project Development and Finance: Advanced Development Concepts

    Energy Savers [EERE]

    Process and Structures Course Outline What we will cover...  About the DOE Office of Indian Energy Education Initiative  Project Financing Structures - Direct Ownership - Partnership Flip - Sale Leaseback - Inverted Lease/Lease Pass-Through  Additional Information and Resources 2 Introduction The U.S. Department of Energy (DOE) Office of Indian Energy Policy and Programs is responsible for assisting Tribes with energy planning and development, infrastructure, energy costs, and

  10. Research and Development - DOE Directives, Delegations, and Requirements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research and Development

  11. ITP Industrial Materials: Development and Commercialization of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Development and Commercialization of Alternative Carbon Fiber Precursors and Conversion Technologies ITP Industrial Materials: Development and Commercialization of Alternative ...

  12. Sandia Energy - Conventional Water Power: Technology Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technology Development Home Stationary Power Energy Conversion Efficiency Water Power Conventional Water Power: Technology Development Conventional Water Power: Technology...

  13. Certifications and Professional Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Certifications and Professional Development Certifications and Professional Development The following information has been moved to Powerpedia: Acquisition Certifications Program ...

  14. CLEERS Coordination & Joint Development of Benchmark Kinetics...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications CLEERS Coordination & Joint Development of Benchmark Kinetics for LNT & SCR CLEERS Coordination & Development of Catalyst Process Kinetic...

  15. Multidimensional simulation and chemical kinetics development...

    Office of Environmental Management (EM)

    Multidimensional simulation and chemical kinetics development for high efficiency clean combustion engines Multidimensional simulation and chemical kinetics development for high ...

  16. Developing an Evaluation Measurement, and Verification Plan:...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Developing an Evaluation Measurement, and Verification Plan: Residential Retrofits Developing an Evaluation Measurement, and Verification Plan: Residential Retrofits DOE's...

  17. Conventional Energy Forum & Associated Vertical Business Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Conventional Energy Forum & Associated Vertical Business Development: Best Practices in Indian Country Conventional Energy Forum & Associated Vertical Business Development: Best ...

  18. Geothermal Electricity Technology Evaluation Model (GETEM) Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Electricity Technology Evaluation Model (GETEM) Development Geothermal Electricity Technology Evaluation Model (GETEM) Development Project objective: Provide a tool for estimating...

  19. Xishuangbanna Tianshengqiao Hydropower Development Co Ltd | Open...

    Open Energy Info (EERE)

    Tianshengqiao Hydropower Development Co Ltd Jump to: navigation, search Name: Xishuangbanna Tianshengqiao Hydropower Development Co., Ltd. Place: Xishuangbanna City, Yunnan...

  20. Kerala Industrial Infrastructure Development Corporation Kinfra...

    Open Energy Info (EERE)

    Kerala Industrial Infrastructure Development Corporation Kinfra Jump to: navigation, search Name: Kerala Industrial Infrastructure Development Corporation (Kinfra) Place:...

  1. ITP Industrial Materials: Development and Commercialization of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ITP Industrial Materials: Development and Commercialization of Alternative Carbon Fiber Precursors and Conversion Technologies ITP Industrial Materials: Development and...

  2. Plasmatron Fuel Reformer Development and Internal Combustion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Plasmatron Fuel Reformer Development and Internal Combustion Engine Vehicle Applications Plasmatron Fuel Reformer Development and Internal Combustion Engine Vehicle Applications ...

  3. Minority Education and Community Development | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Development Minority Education and Community Development Minority serving institutions ... Minority Serving Institutions are institutions of higher education that serve minority ...

  4. Advanced Modular Inverter Technology Development

    SciTech Connect (OSTI)

    Adam Szczepanek

    2006-02-04

    Electric and hybrid-electric vehicle systems require an inverter to convert the direct current (DC) output of the energy generation/storage system (engine, fuel cells, or batteries) to the alternating current (AC) that vehicle propulsion motors use. Vehicle support systems, such as lights and air conditioning, also use the inverter AC output. Distributed energy systems require an inverter to provide the high quality AC output that energy system customers demand. Today's inverters are expensive due to the cost of the power electronics components, and system designers must also tailor the inverter for individual applications. Thus, the benefits of mass production are not available, resulting in high initial procurement costs as well as high inverter maintenance and repair costs. Electricore, Inc. (www.electricore.org) a public good 501 (c) (3) not-for-profit advanced technology development consortium assembled a highly qualified team consisting of AeroVironment Inc. (www.aerovironment.com) and Delphi Automotive Systems LLC (Delphi), (www.delphi.com), as equal tiered technical leads, to develop an advanced, modular construction, inverter packaging technology that will offer a 30% cost reduction over conventional designs adding to the development of energy conversion technologies for crosscutting applications in the building, industry, transportation, and utility sectors. The proposed inverter allows for a reduction of weight and size of power electronics in the above-mentioned sectors and is scalable over the range of 15 to 500kW. The main objective of this program was to optimize existing AeroVironment inverter technology to improve power density, reliability and producibility as well as develop new topology to reduce line filter size. The newly developed inverter design will be used in automotive and distribution generation applications. In the first part of this program the high-density power stages were redesigned, optimized and fabricated. One of the main tasks was to design and validate new gate drive circuits to provide the capability of high temp operation. The new power stages and controls were later validated through extensive performance, durability and environmental tests. To further validate the design, two power stages and controls were integrated into a grid-tied load bank test fixture, a real application for field-testing. This fixture was designed to test motor drives with PWM output up to 50kW. In the second part of this program the new control topology based on sub-phases control and interphase transformer technology was successfully developed and validated. The main advantage of this technology is to reduce magnetic mass, loss and current ripple. This report summarizes the results of the advanced modular inverter technology development and details: (1) Power stage development and fabrication (2) Power stage validation testing (3) Grid-tied test fixture fabrication and initial testing (4) Interphase transformer technology development

  5. Learning and Workforce Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Services » Learning and Workforce Development Learning and Workforce Development Learning Learn about our learning and development planning, mandatory training compliance reporting, and professional skills and technical training. Workforce Development Find links to services that we provide to support our DOE employees through our corporate assessment, evaluation, organizational development and leadership development. Browse by Role Search for tools, information, and programs specific to your

  6. Feasibility of developing a portable driver performance data acquisition system for human factors research: Technical tasks. Volume 1

    SciTech Connect (OSTI)

    Carter, R.J.; Barickman, F.S.; Spelt, P.F.; Schmoyer, R.L.; Kirkpatrick, J.R.

    1998-01-01

    A two-phase, multi-year research program entitled ``development of a portable driver performance data acquisition system for human factors research`` was recently completed. The primary objective of the project was to develop a portable data acquisition system for crash avoidance research (DASCAR) that will allow drive performance data to be collected using a large variety of vehicle types and that would be capable of being installed on a given vehicle type within a relatively short-time frame. During phase 1 a feasibility study for designing and fabricating DASCAR was conducted. In phase 2 of the research DASCAR was actually developed and validated. This technical memorandum documents the results from the feasibility study. It is subdivided into three volumes. Volume one (this report) addresses the last five items in the phase 1 research and the first issue in the second phase of the project. Volumes two and three present the related appendices, and the design specifications developed for DASCAR respectively. The six tasks were oriented toward: identifying parameters and measures; identifying analysis tools and methods; identifying measurement techniques and state-of-the-art hardware and software; developing design requirements and specifications; determining the cost of one or more copies of the proposed data acquisition system; and designing a development plan and constructing DASCAR. This report also covers: the background to the program; the requirements for the project; micro camera testing; heat load calculations for the DASCAR instrumentation package in automobile trunks; phase 2 of the research; the DASCAR hardware and software delivered to the National Highway Traffic Safety Administration; and crash avoidance problems that can be addressed by DASCAR.

  7. Environmental development plan: coal liquefaction

    SciTech Connect (OSTI)

    Not Available

    1980-08-01

    This Environmental Development plan (EDP) examines environmental concerns that are being evaluated for the technologies in DOE's Coal Liquefaction Program. It identifies the actions that are planned or underway to resolve these concerns while the technologies are being developed. Research is scheduled on the evaluation and mitigation of potential environmental impacts. This EDP updates the FY 1977 Coal Liquefaction Program EDP. Chapter II describes the DOE Coal Liquefaction Program and focuses on the Solvent Refined Coal (SRC), H-Coal, and Exxon donor solvent (EDS) processes because of their relatively advanced R and D stages. The major unresolved environmental concerns associated with the coal liquefaction subactivities and projects are summarized. The concerns were identified in the 1977 EDP's and research was scheduled to lead to the resolution of the concerns. Much of this research is currently underway. The status of ongoing and planned research is shown in Table 4-1.

  8. Energy storage research and development

    SciTech Connect (OSTI)

    None, None

    2008-01-01

    In 2007, US consumers experienced the highest sustained gasoline prices in recent history, in real terms, including those seen in the early 1980s1. Partially as a result of the $3/gallon gasoline prices, sales of hybrid electric vehicles (HEVs) increased almost 60% in 20072, and several automakers announced plans to develop plug-in hybrid electric vehicles (PHEVs)3. However, total sales of HEVs remained in the 2-3 percent range of all vehicle sales. An important step for continued HEV market penetration, as well as electrifying the nation's personal transportation, is the development of cost effective, long lasting, and abuse tolerant Li-ion batteries.

  9. Flexible, secure agent development framework

    DOE Patents [OSTI]

    Goldsmith; Steven Y.

    2009-04-07

    While an agent generator is generating an intelligent agent, it can also evaluate the data processing platform on which it is executing, in order to assess a risk factor associated with operation of the agent generator on the data processing platform. The agent generator can retrieve from a location external to the data processing platform an open site that is configurable by the user, and load the open site into an agent substrate, thereby creating a development agent with code development capabilities. While an intelligent agent is executing a functional program on a data processing platform, it can also evaluate the data processing platform to assess a risk factor associated with performing the data processing function on the data processing platform.

  10. Thermal hydraulics development for CASL

    SciTech Connect (OSTI)

    Lowrie, Robert B

    2010-12-07

    This talk will describe the technical direction of the Thermal-Hydraulics (T-H) Project within the Consortium for Advanced Simulation of Light Water Reactors (CASL) Department of Energy Innovation Hub. CASL is focused on developing a 'virtual reactor', that will simulate the physical processes that occur within a light-water reactor. These simulations will address several challenge problems, defined by laboratory, university, and industrial partners that make up CASL. CASL's T-H efforts are encompassed in two sub-projects: (1) Computational Fluid Dynamics (CFD), (2) Interface Treatment Methods (ITM). The CFD subproject will develop non-proprietary, scalable, verified and validated macroscale CFD simulation tools. These tools typically require closures for their turbulence and boiling models, which will be provided by the ITM sub-project, via experiments and microscale (such as DNS) simulation results. The near-term milestones and longer term plans of these two sub-projects will be discussed.

  11. Nucleation and condensation model development

    SciTech Connect (OSTI)

    Fry, H.; Lyman, J.; Breshears, D.; Zerkle, D.; Wilson, C.; Hewitt, C.; Gallegos, D.

    1996-09-01

    This is a final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The purpose of this project was to bring to maturity a theoretical and experimental capability of the Laboratory to perform basic research in nucleation and condensation of water vapor. This report provides a general description of this capability and summarizes specific work in two areas: development and use of a combustive flow facility (CFF) to measure water monomer depletion in a supersonic nozzle and nucleation pulse experiments for investigation of transport effects on water droplet growth dynamics. The later work was performed in collaboration with Dr. Wehrner Strey in Goettingen, Germany. Preliminary water absorption data from the CFF experiment are presented. The nucleation pulse data is described along with an analysis that shows under the condition of the experiment the growth rate of water droplets is limited by monomer diffusion.

  12. Advanced LWR Nuclear Fuel Development

    Energy Savers [EERE]

    LWRS Overview and Select Research Highlights J. Busby and K. Leonard Oak Ridge National Laboratory with a host of contributors Overview Presentation for the Nuclear Energy Enabling Technologies September 15, 2015 Video Conference FY16 - Consolidated Innovative Nuclear Research * Light water reactor sustainability (LWRS) is one of the four technical areas in the Reactor Concepts Research, Development and Demonstration Program sections in the FOA. * Activities in LWRS also overlap with NEET

  13. Development Shop | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Development Shop The Ames Laboratory operates a complete machine shop. Our shop consists of the modern equipment needed to fabricate almost any conceivable device required for research project. If you have a need or any questions about the fabrication of items to support your mission in research please contact us. Our machining equipment includes: Lathes CNC Bridgeport Mills Shears Press Brake (for bending) EDM (Electronic Discharge Machining) Grinders Saws We are capable of welding nearly any

  14. PV Research & Development Activities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research & Development Activities - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management

  15. Arctic Energy Technology Development Laboratory

    SciTech Connect (OSTI)

    Sukumar Bandopadhyay; Charles Chamberlin; Robert Chaney; Gang Chen; Godwin Chukwu; James Clough; Steve Colt; Anthony Covescek; Robert Crosby; Abhijit Dandekar; Paul Decker; Brandon Galloway; Rajive Ganguli; Catherine Hanks; Rich Haut; Kristie Hilton; Larry Hinzman; Gwen Holdman; Kristie Holland; Robert Hunter; Ron Johnson; Thomas Johnson; Doug Kame; Mikhail Kaneveskly; Tristan Kenny; Santanu Khataniar; Abhijeet Kulkami; Peter Lehman; Mary Beth Leigh; Jenn-Tai Liang; Michael Lilly; Chuen-Sen Lin; Paul Martin; Pete McGrail; Dan Miller; Debasmita Misra; Nagendra Nagabhushana; David Ogbe; Amanda Osborne; Antoinette Owen; Sharish Patil; Rocky Reifenstuhl; Doug Reynolds; Eric Robertson; Todd Schaef; Jack Schmid; Yuri Shur; Arion Tussing; Jack Walker; Katey Walter; Shannon Watson; Daniel White; Gregory White; Mark White; Richard Wies; Tom Williams; Dennis Witmer; Craig Wollard; Tao Zhu

    2008-12-31

    The Arctic Energy Technology Development Laboratory was created by the University of Alaska Fairbanks in response to a congressionally mandated funding opportunity through the U.S. Department of Energy (DOE), specifically to encourage research partnerships between the university, the Alaskan energy industry, and the DOE. The enabling legislation permitted research in a broad variety of topics particularly of interest to Alaska, including providing more efficient and economical electrical power generation in rural villages, as well as research in coal, oil, and gas. The contract was managed as a cooperative research agreement, with active project monitoring and management from the DOE. In the eight years of this partnership, approximately 30 projects were funded and completed. These projects, which were selected using an industry panel of Alaskan energy industry engineers and managers, cover a wide range of topics, such as diesel engine efficiency, fuel cells, coal combustion, methane gas hydrates, heavy oil recovery, and water issues associated with ice road construction in the oil fields of the North Slope. Each project was managed as a separate DOE contract, and the final technical report for each completed project is included with this final report. The intent of this process was to address the energy research needs of Alaska and to develop research capability at the university. As such, the intent from the beginning of this process was to encourage development of partnerships and skills that would permit a transition to direct competitive funding opportunities managed from funding sources. This project has succeeded at both the individual project level and at the institutional development level, as many of the researchers at the university are currently submitting proposals to funding agencies, with some success.

  16. Development of GREET Catalyst Module

    SciTech Connect (OSTI)

    Wang, Zhichao; Benavides, Pahola T.; Dunn, Jennifer B.; Cronauer, Donald C.

    2015-09-01

    In this report, we develop energy and material flows for the production of five different catalysts (tar reforming, alcohol synthesis, Zeolite Socony Mobil-5 [ZSM-5], Mo/Co/ γ-Al2O3, and Pt/ γ-Al2O3) and two chemicals (olivine, dimethyl ether of polyethylene glycol [DEPG]). These compounds and catalysts are now included in the Greenhouse Gases, Regulated Emissions and Energy Use in Transportation (GREET™) catalyst module.

  17. Integrated Research, Development, and Deployment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Research, Development, and Deployment - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management

  18. transims-application-and-development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TRANSIMS: Applications and Development Workshop : April 8-9, 2010 Organizers Dr. Hubert Ley Dr. Vadim Sokolov This email address is being protected from spambots. You need JavaScript enabled to view it. Brian Gardner Office of Planning Federal Highway Administration This email address is being protected from spambots. You need JavaScript enabled to view it. Agenda Announcement pdficon small Accompanying Materials Adobe Connect Recording Links Accompanying Materials Introduction to the TRANSIMS

  19. EC RESEARCH AND DEVELOPMENT REPORT .:'

    Office of Legacy Management (LM)

    2, j ,&+~ ,:. x&+,, ; wt. d.' :?.' . ' ~~j~,,~~ &?$;i?$$,i:i~-' _' ' .. EC RESEARCH AND DEVELOPMENT REPORT .:' :' :I :I:.- : . . ' _ -a. :. _. : . . 1 . . ' y:y ,. 1. . :<,*I t..; : !,,!' :.' ...> ,I 43 .r:. :&& i pq7.q 12 w ; ;::> x ,. _ ,.l 2.. r/' -T ."."--- ,' ,;. ;' , , _,' . 2 , ' .. LEGAL NOTICE This report was prepared as an account of Government sponsored work. Neither the United States, nor the Commission, nor any person acting on behalf of the

  20. 2013 Nuclear Workforce Development Day

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nuclear Workforce Development Day ∎ Tuesday, October 22, 2013 Nuclear Medicine Topics:  Pathways of Practice in Nuclear Medicine  Radiopharmacy  Patient Care  Medical Imaging & Computers Moderator: Deborah M. Gibbs, MEd, PET, CNMT Lead Nuclear Medicine / PET Facility Administrator Georgia Regents University Panel Members: Jim Corley, MS, RPh- Associate Professor Georgia Regents University George David, MS, FAAPM- Medical Physicist Georgia Regents University Dr. Gregory

  1. 2013 Nuclear Workforce Development Day

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Savannah River Site Topics:  How are Robotics, Homeland Security & SRS Related?  What are Future Careers at SRS?  Why does SRS have a Gate? Moderator: Steve Hensel - Senior Fellow Engineer Savannah River Nuclear Solutions Panel Members: Steve Tibrea - Director, Research & Development Engineering Savannah River Nuclear Solutions Steve Howell - Deputy Director, Environmental Management Operations - Savannah River Nuclear Solutions Renee Spires - Program Manager Savannah River

  2. Environmental boundaries to energy development

    SciTech Connect (OSTI)

    Trivelpiece, A.W.

    1989-01-01

    Public concern about the environment, health and safety consequences of energy technology has been growing steadily for more than two decades in the United States. This concern forms an important boundary condition as the United States seeks to develop a new National Energy Strategy. Furthermore, the international aspects of the energy/environment interface such as acid rain global climate change and stratospheric ozone depletion are very prominent in US thinking. In fact, the energy systems of the world are becoming more closely coupled environmentally and otherwise. Now where is this coupling more important than that between the industrialized and developing world; the choices made by each will have profound effects on the other. The development of energy technologies compatible with both economic growth and improving and sustaining environmental quality represents a major R D challenge to the US and USSR. Decision about adoption of new technology and R D priorities can be improved by better measurements of how energy sources and uses are changing throughout the world and better methods to project the potential consequences of these decisions. Such projection require understanding relative risks of alternating existing and evolving technologies. All of these R D areas, technology improvement energy system monitoring and projection and comparative risk assessment are the topics of this seminar. Progress in each may be enhanced by collaboration and cooperation between our two countries. 7 refs., 27 figs., 5 tabs.

  3. Report on Advanced Detector Development

    SciTech Connect (OSTI)

    James K. Jewell

    2012-09-01

    Neutron, gamma and charged particle detection improvements are key to supporting many of the foreseen measurements and systems envisioned in the R&D programs and the future fuel cycle requirements, such as basic nuclear physics and data, modeling and simulation, reactor instrumentation, criticality safety, materials management and safeguards. This task will focus on the developmental needs of the FCR&D experimental programs, such as elastic/inelastic scattering, total cross sections and fission neutron spectra measurements, and will leverage a number of existing neutron detector development efforts and programs, such as those at LANL, PNNL, INL, and IAC as well as those at many universities, some of whom are funded under NE grants and contracts. Novel materials and fabrication processes combined with state-of-the-art electronics and computing provide new opportunities for revolutionary detector systems that will be able to meet the high precision needs of the program. This work will be closely coordinated with the Nuclear Data Crosscut. The Advanced Detector Development effort is a broadly-focused activity that supports the development of improved nuclear data measurements and improved detection of nuclear reactions and reactor conditions. This work supports the design and construction of large-scale, multiple component detectors to provide nuclear reaction data of unprecedented quality and precision. Examples include the Time Projection Chamber (TPC) and the DANCE detector at LANL. This work also supports the fabrication and end-user application of novel scintillator materials detection and monitoring.

  4. DEVELOPMENT OF NEW DRILLING FLUIDS

    SciTech Connect (OSTI)

    David B. Burnett

    2003-08-01

    The goal of the project has been to develop new types of drill-in fluids (DIFs) and completion fluids (CFs) for use in natural gas reservoirs. Phase 1 of the project was a 24-month study to develop the concept of advanced type of fluids usable in well completions. Phase 1 tested this concept and created a kinetic mathematical model to accurately track the fluid's behavior under downhole conditions. Phase 2 includes tests of the new materials and practices. Work includes the preparation of new materials and the deployment of the new fluids and new practices to the field. The project addresses the special problem of formation damage issues related to the use of CFs and DIFs in open hole horizontal well completions. The concept of a ''removable filtercake'' has, as its basis, a mechanism to initiate or trigger the removal process. Our approach to developing such a mechanism is to identify the components of the filtercake and measure the change in the characteristics of these components when certain cleanup (filtercake removal) techniques are employed.

  5. Session: Wind industry project development

    SciTech Connect (OSTI)

    Gray, Tom; Enfield, Sam

    2004-09-01

    This first session at the Wind Energy and Birds/Bats workshop consisted of two presentations followed by a question and answer period. The session was intended to provide a general overview of wind energy product development, from the industry's perspective. Tom Gray of AWEA presented a paper titled ''State of the Wind Energy Industry in 2004'', highlighting improved performance and lower cost, efforts to address avian impacts, a status of wind energy in comparison to other energy-producing sources, and ending on expectations for the near future. Sam Enfield of Atlantic Renewable Energy Corporation presented a paper titled ''Key Factors for Consideration in Wind Plant Siting'', highlighting factors that wind facility developers must consider when choosing a site to build wind turbines and associated structures. Factors covered include wind resources available, ownership and land use patterns, access to transmission lines, accessibility and environmental impacts. The question and answer sum mary included topics related to risk taking, research and development, regulatory requirements, and dealing with utilities.

  6. Technology development life cycle processes.

    SciTech Connect (OSTI)

    Beck, David Franklin

    2013-05-01

    This report and set of appendices are a collection of memoranda originally drafted in 2009 for the purpose of providing motivation and the necessary background material to support the definition and integration of engineering and management processes related to technology development. At the time there was interest and support to move from Capability Maturity Model Integration (CMMI) Level One (ad hoc processes) to Level Three. As presented herein, the material begins with a survey of open literature perspectives on technology development life cycles, including published data on %E2%80%9Cwhat went wrong.%E2%80%9D The main thrust of the material presents a rational expose%CC%81 of a structured technology development life cycle that uses the scientific method as a framework, with further rigor added from adapting relevant portions of the systems engineering process. The material concludes with a discussion on the use of multiple measures to assess technology maturity, including consideration of the viewpoint of potential users.

  7. Carbon sequestration research and development

    SciTech Connect (OSTI)

    Reichle, Dave; Houghton, John; Kane, Bob; Ekmann, Jim; and others

    1999-12-31

    Predictions of global energy use in the next century suggest a continued increase in carbon emissions and rising concentrations of carbon dioxide (CO{sub 2}) in the atmosphere unless major changes are made in the way we produce and use energy--in particular, how we manage carbon. For example, the Intergovernmental Panel on Climate Change (IPCC) predicts in its 1995 ''business as usual'' energy scenario that future global emissions of CO{sub 2} to the atmosphere will increase from 7.4 billion tonnes of carbon (GtC) per year in 1997 to approximately 26 GtC/year by 2100. IPCC also projects a doubling of atmospheric CO{sub 2} concentration by the middle of next century and growing rates of increase beyond. Although the effects of increased CO{sub 2} levels on global climate are uncertain, many scientists agree that a doubling of atmospheric CO{sub 2} concentrations could have a variety of serious environmental consequences. The goal of this report is to identify key areas for research and development (R&D) that could lead to an understanding of the potential for future use of carbon sequestration as a major tool for managing carbon emissions. Under the leadership of DOE, researchers from universities, industry, other government agencies, and DOE national laboratories were brought together to develop the technical basis for conceiving a science and technology road map. That effort has resulted in this report, which develops much of the information needed for the road map.

  8. Developing Government Renewable Energy Projects

    SciTech Connect (OSTI)

    Kurt S. Myers; Thomas L. Baldwin; Jason W. Bush; Jake P. Gentle

    2012-07-01

    The US Army Corps of Engineers has retained Idaho National Laboratory (INL) to conduct a study of past INL experiences and complete a report that identifies the processes that are needed for the development of renewable energy projects on government properties. The INL has always maintained expertise in power systems and applied engineering and INL’s renewable energy experiences date back to the 1980’s when our engineers began performing US Air Force wind energy feasibility studies and development projects. Over the last 20+ years of working with Department of Defense and other government agencies to study, design, and build government renewable projects, INL has experienced the do’s and don’ts for being successful with a project. These compiled guidelines for government renewable energy projects could include wind, hydro, geothermal, solar, biomass, or a variety of hybrid systems; however, for the purpose of narrowing the focus of this report, wind projects are the main topic discussed throughout this report. It is our thought that a lot of what is discussed could be applied, possibly with some modifications, to other areas of renewable energy. It is also important to note that individual projects (regardless the type) vary to some degree depending on location, size, and need but in general these concepts and directions can be carried over to the majority of government renewable energy projects. This report focuses on the initial development that needs to occur for any project to be a successful government renewable energy project.

  9. New Mexico renewable development study

    SciTech Connect (OSTI)

    Toole, Gasper [Los Alamos National Laboratory; Bent, Russell [Los Alamos National Laboratory; Ewers, Mary [Los Alamos National Laboratory

    2010-09-17

    Since the early 1990s, Los Alamos National Laboratory (LANL) has applied electric grid models and simulation software to problems of national significance. This effort continues with a variety of other projects funded by the Department of Energy (DOE), other federal and state agencies and private companies. Critical to the success of these programs is the ability to integrate regional-scale models of the electric grid, to assess the propagation of grid impacts, and to present interactively the effect of potential mitigating actions required to stabilize the grid. All of these capabilities are applied in this study, to accomplish the following goals and objectives: (1) Develop an AC power flow model representing future conditions within New Mexico's electric grid, using commercial tools accepted by the utility industry; (2) Conduct a 'screening' analysis of options for accelerating potential renewable energy development through the addition of a statewide transmission collector system; (3) Estimate total revenue needed, jobs created (temporary and permanent) plus indirect and direct impacts to the state's economy; (4) Evaluate potential cost allocation methodology; and (5) Issue a project report that will provide information for policy direction by state regulators, project developers, and legislators.

  10. Wind Development on Tribal Lands

    SciTech Connect (OSTI)

    Ken Haukaas; Dale Osborn; Belvin Pete

    2008-01-18

    Background: The Rosebud Sioux Tribe (RST) is located in south central South Dakota near the Nebraska border. The nearest community of size is Valentine, Nebraska. The RST is a recipient of several Department of Energy grants, written by Distributed Generation Systems, Inc. (Disgen), for the purposes of assessing the feasibility of its wind resource and subsequently to fund the development of the project. Disgen, as the contracting entity to the RST for this project, has completed all the pre-construction activities, with the exception of the power purchase agreement and interconnection agreement, to commence financing and construction of the project. The focus of this financing is to maximize the economic benefits to the RST while achieving commercially reasonable rates of return and fees for the other parties involved. Each of the development activities required and its status is discussed below. Land Resource: The Owl Feather War Bonnet 30 MW Wind Project is located on RST Tribal Trust Land of approximately 680 acres adjacent to the community of St. Francis, South Dakota. The RST Tribal Council has voted on several occasions for the development of this land for wind energy purposes, as has the District of St. Francis. Actual footprint of wind farm will be approx. 50 acres. Wind Resource Assessment: The wind data has been collected from the site since May 1, 2001 and continues to be collected and analyzed. The latest projections indicate a net capacity factor of 42% at a hub height of 80 meters. The data has been collected utilizing an NRG 9300 Data logger System with instrumentation installed at 30, 40 and 65 meters on an existing KINI radio tower. The long-term annual average wind speed at 65-meters above ground level is 18.2 mph (8.1 mps) and 18.7 mph (8.4 mps) at 80-meters agl. The wind resource is excellent and supports project financing.

  11. ENERGY RESEARCH AND DEVELOPMENT ADMINISTRATION

    Office of Legacy Management (LM)

    .' :h I : ' ENERGY RESEARCH AND DEVELOPMENT ADMINISTRATION WASHINGTON, D.C. 20545 October 24, 1975 :~.. ,. Memo to Piles' CARNEGIE-MELLON S~C&RCCYCLOTRON On October 23, 1975, W. J. McCool (HQOS), E. K. Loop (HQ-OS), R. E. Allen (HQ-OS), J. Pingel (CH), B. 3. Davis (CH), R. Drucker (CR-BAO) and I met at Germantown to discuss the clean-up of radio- activity at the Saxonburg accelerator site. After discussion, we concluded acceptable criteria would include removal of all material necessary to

  12. Data mining for ontology development.

    SciTech Connect (OSTI)

    Davidson, George S.; Strasburg, Jana; Stampf, David; Neymotin,Lev; Czajkowski, Carl; Shine, Eugene; Bollinger, James; Ghosh, Vinita; Sorokine, Alexandre; Ferrell, Regina; Ward, Richard; Schoenwald, David Alan

    2010-06-01

    A multi-laboratory ontology construction effort during the summer and fall of 2009 prototyped an ontology for counterfeit semiconductor manufacturing. This effort included an ontology development team and an ontology validation methods team. Here the third team of the Ontology Project, the Data Analysis (DA) team reports on their approaches, the tools they used, and results for mining literature for terminology pertinent to counterfeit semiconductor manufacturing. A discussion of the value of ontology-based analysis is presented, with insights drawn from other ontology-based methods regularly used in the analysis of genomic experiments. Finally, suggestions for future work are offered.

  13. Development of MEMS photoacoustic spectroscopy

    SciTech Connect (OSTI)

    Robinson, Alex Lockwood; Eichenfield, Matthew S.; Griffin, Benjamin; Harvey, Heidi Alyssa; Nielson, Gregory N.; Okandan, Murat; Langlois, Eric; Resnick, Paul James; Shaw, Michael J.; Young, Ian; Givler, Richard C.; Reinke, Charles M.

    2014-01-01

    After years in the field, many materials suffer degradation, off-gassing, and chemical changes causing build-up of measurable chemical atmospheres. Stand-alone embedded chemical sensors are typically limited in specificity, require electrical lines, and/or calibration drift makes data reliability questionable. Along with size, these "Achilles' heels" have prevented incorporation of gas sensing into sealed, hazardous locations which would highly benefit from in-situ analysis. We report on development of an all-optical, mid-IR, fiber-optic based MEMS Photoacoustic Spectroscopy solution to address these limitations. Concurrent modeling and computational simulation are used to guide hardware design and implementation.

  14. Energy Development Opportunities for Wyoming

    SciTech Connect (OSTI)

    Larry Demick

    2012-11-01

    The Wyoming Business Council, representing the state’s interests, is participating in a collaborative evaluation of energy development opportunities with the NGNP Industry Alliance (an industry consortium), the University of Wyoming, and the US Department of Energy’s Idaho National Laboratory. Three important energy-related goals are being pursued by the State of Wyoming: Ensuring continued reliable and affordable sources of energy for Wyoming’s industries and people Restructuring the coal economy in Wyoming Restructuring the natural gas economy in Wyoming

  15. Workforce Development Wind Projects | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Workforce Development Wind Projects Workforce Development Wind Projects This report covers the Wind and Water Power Technologies Office's workforce development wind projects from fiscal years 2008 to 2014. PDF icon Workforce Development Wind Projects.pdf More Documents & Publications Testing, Manufacturing, and Component Development Projects Wind Integration, Transmission, and Resource Assessment and Characterization Projects Environmental Wind Projects

  16. Urenco centrifuge and laser development

    SciTech Connect (OSTI)

    Upson, P.C.

    1994-12-31

    The Urenco centrifuge process for the enrichment of uranium is now well developed and economically proven. The centrifuge technology that forms the basis of Urenco`s plants in the United Kingdom, the Netherlands, and Germany has evolved steadily over the last two decades since the Urenco partnership was formed, and current programs of development will see this progress continue into the next century. From the early pilot plant work, the first generation of machines was installed and commissioned in the late 1970s in the U.K. and Netherlands plants. These have both significantly exceeded the original design expectation with respect to both stress lifetime and corrosion resistance. The early U.K. plant was shut down in 1992, again well beyond the expected 10-yr lifetime, while the Netherlands plant is still operating. Since then, significant advances have been made, and a fourth-generation machine began operation in the plants in 1991; in fact, Urenco has all four generations still in operation in its plants today. Urenco`s research on laser isotope separation is also described.

  17. Development of New Stainless Steel

    SciTech Connect (OSTI)

    Robert F. Buck

    2005-08-30

    A new family of innovative martensitic stainless steels, 521-A, 521-B, and 521-C has been developed by Advanced Steel Technology, LLC (Trafford, PA) as high strength fastener (bolt) materials for use at moderate temperatures in turbine engines, including steam turbines, gas turbines, and aircraft engines. The primary objective of the development program was to create a martensitic stainless steel with high strength at moderate temperatures, and which could replace the expensive nickel-based superalloy IN 718 in some fasteners applications. A secondary objective was to replace conventional 12Cr steels such as AISI 422 used as blades, buckets and shafts that operate at intermediate temperatures in turbine engines with stronger steel. The composition of the new alloys was specifically designed to produce excellent mechanical properties while integrating heat treatment steps into production to reduce energy consumption during manufacturing. As a result, production costs and energy consumption during production of rolled bar products is significantly lower than conventional materials. Successful commercialization of the new alloys would permit the installed cost of certain turbine engines to be reduced without sacrificing high availability or operational flexibility, thereby enhancing the global competitiveness of U.S. turbine engine manufacturers. Moreover, the domestic specialty steel industry would also benefit through increased productivity and reduced operating costs, while increasing their share of the international market for turbine engine fasteners, blades, buckets and shafts.

  18. AGING SYSTEM DESIGN DEVELOPMENT STRATEGY

    SciTech Connect (OSTI)

    J. Beesley

    2005-02-07

    This plan provides an overview, work to date, and the path forward for the design development strategy of the Aging cask for aging commercial spent nuclear fuel (CSNF) at the Yucca Mountain Project (YMP) repository site. Waste for subsurface emplacement at the repository includes US Department of Energy (DOE) high-level radioactive waste (HLW), DOE SNF, commercial fuel in dual-purpose canisters (DPCs), uncanistered bare fuel, naval fuel, and other waste types. Table 1-1 lists the types of radioactive materials that may be aged at YMP, and those materials that will not be placed in an aging cask or module. This plan presents the strategy for design development of the Aging system. The Aging system will not handle naval fuel, DOE HLW, MCOs, or DOE SNF since those materials will be delivered to the repository in a state and sequence that allows them to be placed into waste packages for emplacement. Some CSNF from nuclear reactors, especially CSNF that is thermally too hot for emplacement underground, will need to be aged at the repository.

  19. Process Development for Nanostructured Photovoltaics

    SciTech Connect (OSTI)

    Elam, Jeffrey W.

    2015-01-01

    Photovoltaic manufacturing is an emerging industry that promises a carbon-free, nearly limitless source of energy for our nation. However, the high-temperature manufacturing processes used for conventional silicon-based photovoltaics are extremely energy-intensive and expensive. This high cost imposes a critical barrier to the widespread implementation of photovoltaic technology. Argonne National Laboratory and its partners recently invented new methods for manufacturing nanostructured photovoltaic devices that allow dramatic savings in materials, process energy, and cost. These methods are based on atomic layer deposition, a thin film synthesis technique that has been commercialized for the mass production of semiconductor microelectronics. The goal of this project was to develop these low-cost fabrication methods for the high efficiency production of nanostructured photovoltaics, and to demonstrate these methods in solar cell manufacturing. We achieved this goal in two ways: 1) we demonstrated the benefits of these coatings in the laboratory by scaling-up the fabrication of low-cost dye sensitized solar cells; 2) we used our coating technology to reduce the manufacturing cost of solar cells under development by our industrial partners.

  20. Developing a Regional Recovery Framework

    SciTech Connect (OSTI)

    Lesperance, Ann M.; Olson, Jarrod; Stein, Steven L.; Clark, Rebecca; Kelly, Heather; Sheline, Jim; Tietje, Grant; Williamson, Mark; Woodcock, Jody

    2011-09-01

    Abstract A biological attack would present an unprecedented challenge for local, state, and federal agencies; the military; the private sector; and individuals on many fronts ranging from vaccination and treatment to prioritization of cleanup actions to waste disposal. To prepare the Seattle region to recover from a biological attack, the Seattle Urban Area Security Initiative (UASI) partners collaborated with military and federal agencies to develop a Regional Recovery Framework for a Biological Attack in the Seattle Urban Area. The goal was to reduce the time and resources required to recover and restore wide urban areas, military installations, and other critical infrastructure following a biological incident by providing a coordinated systems approach. Based on discussions in small workshops, tabletop exercises, and interviews with emergency response agency staff, the partners identified concepts of operation for various areas to address critical issues the region will face as recovery progresses. Key to this recovery is the recovery of the economy. Although the Framework is specific to a catastrophic, wide-area biological attack using anthrax, it was designed to be flexible and scalable so it could also serve as the recovery framework for an all-hazards approach. The Framework also served to coalesce policy questions that must be addressed for long-term recovery. These questions cover such areas as safety and health, security, financial management, waste management, legal issues, and economic development.

  1. Developer - Q & A | OpenEI Community

    Open Energy Info (EERE)

    Developer header Developer - Q & A Home > Developer Content Group Activity By term Q & A Feeds Question Post date Answers How to access older versions of rates? 7 Sep 2015 - 16:22...

  2. Expanding the Trilinos developer community. (Technical Report...

    Office of Scientific and Technical Information (OSTI)

    Trilinos as developers. To-date we have worked with external developers in an ad hoc fashion. Going forward, we want to develop a set of policies, procedures, tools and...

  3. Ripeness sensor development. Final report

    SciTech Connect (OSTI)

    Not Available

    1992-11-01

    About 20--25% of the total production of fruits and vegetables in the USA must be discarded after harvest About 25--30% of this loss is the result of over-ripening and this loss represents about 8.39 {times} 10{sup 12} BTU of invested energy every year. This invested energy could be saved by non-destructive ripeness sensing. Sweetness is an important indicator of fruit quality and highly correlated with ripeness in most fruits. Research to develop a non-destructive fruit ripeness sensor has been conducted in the Agricultural Engineering Department at Purdue University. It is based on {sup 1}H-MR (proton Magnetic Resonance). A first generation prototype of the ripeness sensor based on {sup 1}H-MR was built and tested with. Results show that the sensor can discriminate small fruit (0.75 in diameter or smaller) differing in sugar content by 6%. This prototype can separate the fruit into at least two groups: one ripe and the other not ripe. The estimated cost for such a ripeness sensor is around $4,000. The signal sensitivity of the prototype can be improved to enable it to differentiate between fruits varying in sugar content by only 1 or 2% by using water peak suppression techniques to recover relatively weak sugar resonance signals in intact fruits, modifying circuits to eliminate noise, leakage and distortion of input/output signals, improving the magnetic console to get a higher magnetic field and better homogeneity, and designing a probe to achieve a higher signal-to-noise (S/N) ratio. As research continues a second generation ripeness sensor will be developed which will incorporate many of the improvements and which will be suitable for commercial use. Additional research will allow application of the technique to a wider range of fruit sizes (from blueberries to watermelons). This report describes estimated energy savings, feasibility studies, development of the initial prototype, and preliminary evaluation of the first generation prototype.

  4. NREL: Technology Deployment - Project Development Model

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Project Development Model NREL developed the Project Development Model to evaluate the risks and investment decisions required for successful renewable energy project development. The two-phase iterative model includes elements in project fundamentals and project development based off commercial project development practices supported by tools such as pro formas and checklists. Project Fundamentals or BEPTC(tm) State & Local Energy Data Enter a city and state or zip code in the State and

  5. Development of BWR plant analyzer

    SciTech Connect (OSTI)

    Wulff, W.; Cheng, H.S.; Lekach, S.V.; Stritar, A.; Mallen, A.N.

    1984-01-01

    The BWR Plant Analyzer has been developed for realistic and accurate simulations of normal and severe abnormal transients in BWR power plants at high simulation speeds, low capital and operating costs and with outstanding user conveniences. The simulation encompasses neutron kinetics, heat conduction in fuel structures, nonequilibrium, nonhomogeneous coolant dynamics, steam line acoustics, and the dynamics of turbines, condensers, feedwater pumps and heaters, of the suppression pool, the control systems and the plant protection systems. These objectives have been achieved. Advanced modeling, using extensively analytical integration and dynamic evaluation of analytical solutions, has been combined with modern minicomputer technology for high-speed simulation of complex systems. The High-Speed Interactive Plant Analyzer code HIPA-BWR has been implemented on the AD10 peripheral parallel processor.

  6. Hanford Site sustainable development initiatives

    SciTech Connect (OSTI)

    Sullivan, C.T.

    1994-05-01

    Since the days of the Manhattan Project of World War II, the economic well being of the Tri-Cities (Pasco, Kennewick, and Richland) of Washington State has been tied to the US Department of Energy missions at the nearby Hanford Site. As missions at the Site changed, so did the economic vitality of the region. The Hanford Site is now poised to complete its final mission, that of environmental restoration. When restoration is completed, the Site may be closed and the effect on the local economy will be devastating if action is not taken now. To that end, economic diversification and transition are being planned. To facilitate the process, the Hanford Site will become a sustainable development demonstration project.

  7. Development of alkaline fuel cells.

    SciTech Connect (OSTI)

    Hibbs, Michael R.; Jenkins, Janelle E.; Alam, Todd Michael; Janarthanan, Rajeswari; Horan, James L.; Caire, Benjamin R.; Ziegler, Zachary C.; Herring, Andrew M.; Yang, Yuan; Zuo, Xiaobing; Robson, Michael H.; Artyushkova, Kateryna; Patterson, Wendy; Atanassov, Plamen Borissov

    2013-09-01

    This project focuses on the development and demonstration of anion exchange membrane (AEM) fuel cells for portable power applications. Novel polymeric anion exchange membranes and ionomers with high chemical stabilities were prepared characterized by researchers at Sandia National Laboratories. Durable, non-precious metal catalysts were prepared by Dr. Plamen Atanassov's research group at the University of New Mexico by utilizing an aerosol-based process to prepare templated nano-structures. Dr. Andy Herring's group at the Colorado School of Mines combined all of these materials to fabricate and test membrane electrode assemblies for single cell testing in a methanol-fueled alkaline system. The highest power density achieved in this study was 54 mW/cm2 which was 90% of the project target and the highest reported power density for a direct methanol alkaline fuel cell.

  8. Trends in gas turbine development

    SciTech Connect (OSTI)

    Day, W.H.

    1999-07-01

    This paper represents the Gas Turbine Association's view of the gas turbine industry's R and D needs following the Advanced Turbine Systems (ATS) Program which is funded by the U.S. Department of Energy (DOE). Some of this information was discussed at the workshop Next Generation Gas Turbine Power Systems, which was held in Austin, TX, February 9--10, 1999, sponsored by DOE-Federal Energy Technology Center (FETC), reference 1. The general idea is to establish public-private partnerships to reduce the risks involved in the development of new technologies which results in public benefits. The recommendations in this paper are focused on gas turbines > 30 MW output. Specific GTA recommendations on smaller systems are not addressed here. They will be addressed in conjunction with DOE-Energy Efficiency.

  9. The Basis Code Development System

    Energy Science and Technology Software Center (OSTI)

    1994-03-15

    BASIS9.4 is a system for developing interactive computer programs in Fortran, with some support for C and C++ as well. Using BASIS9.4 you can create a program that has a sophisticated programming language as its user interface so that the user can set, calculate with, and plot, all the major variables in the program. The program author writes only the scientific part of the program; BASIS9.4 supplies an environment in which to exercise that scientificmore » programming which includes an interactive language, an interpreter, graphics, terminal logs, error recovery, macros, saving and retrieving variables, formatted I/O, and online documentation.« less

  10. Recent development in green buildings

    SciTech Connect (OSTI)

    Mei, V.C.

    1996-12-31

    Because of the environmental concerns about some materials used in buildings, particularly chlorofluorocarbon (CFC) fluids used as the blowing agent for insulation materials and as refrigerants used in the air conditioning systems have led to a search for environmentally safe alternatives. For insulation materials, new non-CFC blowing agents are still under development. However, the old insulation materials in the buildings will stay because they do not pose any further environmental damage. It is a different story for refrigerants used in air conditioning systems. This study reports that the change-over from CFC to non-CFC refrigerants in the existing and future air conditioning equipment could be a chance not only to take care of the environmental concerns, but to save energy as well. Alternative air conditioning technologies, such as the desiccant dehumidification and absorption systems, and the potential of some natural substances, such as carbon dioxide, as the future refrigerants are also discussed.

  11. Research and development joint ventures

    SciTech Connect (OSTI)

    Not Available

    1984-01-01

    Three panels made up of members of Congress and representatives of research and high technology industries testified at a hearing held to consider H.R. 1952 and H.R. 3393, both bills dealing with joint venture policies that diminish US competitiveness. The bills are designed to eliminate disincentives stemming from antitrust concerns about joint research and development (R and D) activities and to encourage private investment in R and D. The witnesses were asked to evaluate and compare the potential of these bills to overcome institutional barriers and to stimulate capital formation. Three appendices with statements from the National Association of Manufacturers, the Semiconductor Industry Association, and the Institute of Electrical and Electronics Engineers submitted for the record follow the testimony of the eight witnesses. (DCK)

  12. Technical developments of OTEC Systems

    SciTech Connect (OSTI)

    Trenka, A.R.; Thomas, A.; Vega, L.

    1988-01-01

    The US Department of Energy's (DOE) Ocean Energy Technology Program seeks to develop the technology of converting the ocean's vast energy resource into usable forms to the point where industry can assess its potential, commercial utility. The current focus in the program is on the utilization of open-cycle OTEC to produce electricity. The open-cycle OTEC process is one of the few alternative energy options which provides the potential for baseload-carrying capability. This paper provides a very brief overview of the program activities and focuses on results recently obtained from the program's experimental facility designed to allow testing of OC-OTEC subsystems under actual operating conditions utilizing seawater. The facility, referred to as the Seacoast Test Facility (STF), is currently composed of a Heat and Mass Transfer Scoping Test Apparatus (HMTSTA) being supplied by up to 1600 gallons per minute of warm seawater and 1000 gallons per minute of cold seawater. Researchers have obtained experimental data on the performance of evaporators and surface condensers. Also, information on mist elimination and deaeration processes have been obtained. Plans call for modification to the HMTSTA to accommodate the addition of direct-contact condensers. Summary results will be discussed addressing recent studies, by Argonne National Laboratory (ANL), of corrosion and biofouling of aluminum alloy surface condensers. Also discussed is the production of desalinated seawater using an open-cycle OTEC process. Finally to be discussed will be recent developments in OTEC turbines and an assessment of seawater supply systems required for OTEC. A brief overview of the program's future plans also will be presented. 4 refs., 11 figs., 2 tabs.

  13. Sodium Heat Engine Development Program

    SciTech Connect (OSTI)

    Singh, J.P.; Kupperman, D.S.; Majumdar, S.; Dorris, S.; Gopalsami, N.; Dieckman, S.L.; Jaross, R.A.; Johnson, D.L.; Gregar, J.S.; Poeppel, R.B.; Raptis, A.C.; Valentin, R.A.

    1992-01-01

    The Sodium Heat Engine (SHE) is an efficient thermoelectric conversion device which directly generates electricity from a thermally regenerative electrochemical cell that relies on the unique conduction properties of {beta}{double prime}-alumina solid electrolyte (BASE). Laboratory models of a variety of SHE devices have demonstrated the feasibility and efficiency of the system, engineering development of large prototype devices has been slowed by a series of materials and fabrication problems. Failure of the electrolyte tubes has been a recurring problem and a number of possible causes have been postulated. To address these issues, a two-phase engineering development program was undertaken. This report summarizes the final results of the first phase of the program, which included extensive materials characterization activities, a study of applicable nondestructive evaluation methods, an investigation of possible stress states that would contribute to fracture, and certain operational issues associated with the electromagnetic pumps used in the SHE prototype. Mechanical and microstructural evaluation of commercially obtained BASE tubes revealed that they should be adequate for SHE applications and that sodium exposure produced no appreciable deleterious strength effects. Processing activities to produce a more uniform and smaller grain size for the BASE tubes were completed using isostatic pressing, extrusion, and slip casting. Green tubes were sintered by conventional and microwave plasma methods. Of particular interest is the residual stress state in the BASE tubes, and both analysis and nondestructive evaluation methods were employed to evaluate these stresses. X-ray and neutron diffraction experiments were performed to determine the bulk residual stresses in commercially fabricated BASE tubes; however, tube-to-tube variations and variations among the various methods employed did not allow formulation of a definitive definition of the as-fabricated stress state.

  14. New developments in hardfacing alloys

    SciTech Connect (OSTI)

    Menon, R.

    1996-02-01

    The hardfacing industry has matured substantially since its inception in the early 1920s. Numerous welding alloys have been developed and field proven. By developing a strong working knowledge of available alloys, wear conditions and the specific wear situation, the goal of selecting the proper alloy to prolong service life and fight wear is now more attainable than ever. Hardfacing is the process in which a coating or cladding is applied to a substrate for the main purpose of reducing wear or loss of material by abrasion, impact, erosion, galling and cavitation. Most service environments involve a combination of these factors. The choice of an alloy system depends to a great degree on the nature of the wear process encountered. This can range from a simple low-stress condition to a very complex situation that involves abrasion combined with a corrodant and high temperature. The list of possible wear conditions is outlined below: (1) low-stress abrasion, (2) high-stress abrasion, (3) impact, (4) metal-to-metal wear, (5) erosion, and (6) cavitation erosion. In general, service conditions involve a combination of several of the conditions listed above. In addition to the type of wear, three other factors are also important as far as the severity of the wear condition is concerned. These are: (1) type of abradant, (2) service temperature, and (3) service environment. It is clear that in terms of the nature of the wear process as well as the environmental conditions, service conditions are extremely complex. They are, therefore, difficult to simulate in the laboratory. The selection of hardfacing alloys for an application is based primarily on actual field experiences and these are refined with data gathered with time.

  15. ORISE: Cytogenetic Biodosimetry Laboratory Helps Develop International...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Cytogenetic Biodosimetry Laboratory Helps Develop International Web-Based, ... role in the development of an entirely Web-based scoring system, which is being funded ...

  16. International Institute for Sustainable Development (IISD) |...

    Open Energy Info (EERE)

    while retaining the institutional agility necessary to confront the challenges of sustainable development. Resources IISD Tools Building REDD Capacity in Developing...

  17. World Business Council for Sustainable Development (WBCSD) |...

    Open Energy Info (EERE)

    with sustainable development in business. The council focuses on four key areas: 1. Energy and Climate 2. Development 3. The Business Role 4. Ecosystems2 References ...

  18. Technology Development Park PADETEC | Open Energy Information

    Open Energy Info (EERE)

    Development Park PADETEC Jump to: navigation, search Name: Technology Development Park (PADETEC) Place: Brazil Sector: Services Product: General Financial & Legal Services (...

  19. Local Option- Industrial Facilities and Development Bonds

    Broader source: Energy.gov [DOE]

    Under the Utah Industrial Facilities and Development Act, counties, municipalities, and state universities in Utah may issue Industrial Revenue Bonds (IRBs) or Industrial Development Bonds (IDBs)...

  20. Kugler Development Investments Ltd | Open Energy Information

    Open Energy Info (EERE)

    Ltd Jump to: navigation, search Name: Kugler Development & Investments Ltd Place: Israel Sector: Solar Product: Based in Tel-Aviv, Kugler Development & Investments is an...

  1. Regulatory Considerations for Developing Distributed Generation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Regulatory Considerations for Developing Distributed Generation Projects Webinar May 23, 2012 Regulatory Considerations for Developing Distributed Generation Projects Webinar May 23, ...

  2. Aquantis Development Co | Open Energy Information

    Open Energy Info (EERE)

    navigation, search Name: Aquantis Development Co. Place: Florida Product: Aquantis is a tidal energy developer currently planning a project off the coast of Florida. References:...

  3. Nanjing Langdun Lvyuan Environment Technology Development Co...

    Open Energy Info (EERE)

    Lvyuan Environment Technology Development Co Ltd Jump to: navigation, search Name: Nanjing Langdun Lvyuan Environment Technology Development Co Ltd Place: Nanjing, Jiangsu...

  4. TS Wind Power Developers | Open Energy Information

    Open Energy Info (EERE)

    TS Wind Power Developers Jump to: navigation, search Name: TS Wind Power Developers Place: Satara, Maharashtra, India Sector: Wind energy Product: Setting up 30MW wind farm in...

  5. Steinbine Development LLC | Open Energy Information

    Open Energy Info (EERE)

    Wisconsin Sector: Hydro Product: US-based company that develops and manages small hydroelectric plants. References: Steinbine Development LLC1 This article is a stub. You can...

  6. Potential Hydroelectric Development at Existing Federal Facilities...

    Open Energy Info (EERE)

    Potential Hydroelectric Development at Existing Federal Facilities Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Potential Hydroelectric Development at...

  7. Assam Energy Development Agency | Open Energy Information

    Open Energy Info (EERE)

    Energy Development Agency Jump to: navigation, search Name: Assam Energy Development Agency Place: Guwahati, Assam, India Zip: 781005 Sector: Renewable Energy Product: Nodal agency...

  8. Goa Energy Development Agency | Open Energy Information

    Open Energy Info (EERE)

    Goa Energy Development Agency Jump to: navigation, search Name: Goa Energy Development Agency Place: Bardez, Goa, India Zip: 403511 Sector: Renewable Energy Product: Nodal agency...

  9. Validated SCR Concept Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Validated SCR Concept Development Validated SCR Concept Development Poster presentation at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 ...

  10. Travois Indian Country Affordable Housing & Economic Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Travois Indian Country Affordable Housing & Economic Development Conference Travois Indian Country Affordable Housing & Economic Development Conference April 4, 2016 8:00AM CDT to ...

  11. Environmental Impacts of Increased Hydroelectric Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Impacts of Increased Hydroelectric Development at Existing Dams Environmental Impacts of Increased Hydroelectric Development at Existing Dams This report describes the ...

  12. Workforce and Economic Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Workforce and Economic Development Workforce and Economic Development Slides presented in the "What's Working in Residential Energy Efficiency Upgrade Programs Conference - ...

  13. Hydrogen Fuel Quality - Focus: Analytical Methods Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Quality - Focus: Analytical Methods Development & Hydrogen Fuel Quality Results Hydrogen Fuel Quality - Focus: Analytical Methods Development & Hydrogen Fuel Quality Results ...

  14. NETL Cooperative Research and Development Agreements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    research and development performed by NETL and CRADA participant researchers. Background intellectual property (IP) protection is included for both parties, and CRADA developed IP...

  15. National Laboratory Research and Development Funding Opportunities

    Broader source: Energy.gov [DOE]

    Through the National Laboratory Research and Development program, DOE supports research and development and core capabilities at its national laboratories to accelerate progress toward achieving...

  16. Technikon Green Energy Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technikon Green Energy Development Technikon Green Energy Development Presented at the Renewable Hydrogen Workshop, Nov. 16, 2009, in Palm Springs, CA PDF icon ...

  17. Coastal Development Permit Application | Open Energy Information

    Open Energy Info (EERE)

    Development Permit Application Jump to: navigation, search OpenEI Reference LibraryAdd to library Reference: Coastal Development Permit Application Published Publisher Not...

  18. Huadian Hongli Hydropower Investment Development Company | Open...

    Open Energy Info (EERE)

    Hongli Hydropower Investment Development Company Jump to: navigation, search Name: Huadian Hongli Hydropower Investment Development Company Place: Huadian City, Jilin Province,...

  19. Human Resources Specialist (Human Resources Development)

    Broader source: Energy.gov [DOE]

    This position is located in the Leadership and Organizational Development group of Learning and Development (NHT), Human Capital Management (NH), Chief Administrative Officer (N). Human Capital...

  20. Mianyang Taidu Enviroment Energy Technical Development Company...

    Open Energy Info (EERE)

    Mianyang Taidu Enviroment Energy Technical Development Company Ltd Jump to: navigation, search Name: Mianyang Taidu Enviroment Energy Technical Development Company Ltd. Place:...