Powered by Deep Web Technologies
Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Wood Handbook Wood as an Engineering Material Centennial EditionCentennial Edition  

E-Print Network (OSTI)

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

United States; Forest Service; Wood Handbook; Wood As An Engineering Material

2010-01-01T23:59:59.000Z

2

Forestry Policies (Vermont) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Vermont) Vermont) Forestry Policies (Vermont) < Back Eligibility Commercial Agricultural Program Info State Vermont Program Type Environmental Regulations Provider Vermont Department of Forests, Parks and Recreation Vermont forests cover nearly 5 million acres, a large portion of the state. These lands are managed by the Vermont Division of Forestry (http://www.vtfpr.org/htm/forestry.cfm). The Division completed its Forest Resources Plan in 2010, which includes discussion of forest wood for energy: http://www.vtfpr.org/htm/documents/VT%20Forest%20Resources%20Plan.pdf In 2007 the Biomass Energy Resource Center issued "The Vermont Wood Fuel Supply Study", a review of the availability, location, estimated cost, and recommendations for woody biomass material from Vermont forests:

3

Forestry Policies (Maine) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maine) Maine) Forestry Policies (Maine) < Back Eligibility Commercial Agricultural Program Info State Maine Program Type Environmental Regulations Provider Maine Forest Service Maine has diverse forest lands which support a diverse and strong forest products industry. The vast majority of forest lands in the state are privately owned. The Maine Forest Service completed its State Forest Assessment and Strategy in 2010, a plan that includes the goal of enhanced benefit from the production of renewable energy using wood and wood wastes. The combination of markets including a growing biomass energy industry and increased wood heating have created significant demand for wood material in Maine. The Maine Forest Service together with the University of Maine issued its "Woody Biomass Retention Guidelines" in 2010. This document

4

Forestry Policies (Maryland) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

You are here You are here Home » Forestry Policies (Maryland) Forestry Policies (Maryland) < Back Eligibility Agricultural Commercial Program Info State Maryland Program Type Environmental Regulations Provider Department of Natural Resources Maryland's forests are managed by the Department of Natural Resources, Forest Service Division. The Forest Service issued in 2010 its Forest Strategy Document: http://www.dnr.md.gov/forests/pdfs/sas/MDForestStrategy.pdf In 2009 The State issued the Sustainable Forestry Act, which includes discussion of new forest markets including renewable energy development through biomass energy. In 2010 The Sustainable Forestry Council, created by the Sustainable Forestry Act, issued "Wood Energy Potential in Maryland": http://www.dnr.state.md.us/forests/sfcouncil.asp

5

Forestry Policies (West Virginia) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Forestry Policies (West Virginia) Forestry Policies (West Virginia) Forestry Policies (West Virginia) < Back Eligibility Agricultural Commercial Program Info State West Virginia Program Type Environmental Regulations Provider Department of Commerce West Virginia's Forests are managed by the State Division of Forestry. In 2010 the State issues its Forest Resource Assessment: http://www.wvforestry.com/DOF100Assessment_Revised_091310_Part1.pdf The report summarizes available woody biomass resources, citing harvesting cost as a limiting factor due to complex terrain. In 2010 the Forestry Division issued the document "Strategic Plan for the sustainability of West Virginia Forests", which included a section summarizing the State Forester's Report to FMRC on the use of wood biomass from West Virginia forests:

6

Forestry Policies (South Carolina) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Forestry Policies (South Carolina) Forestry Policies (South Carolina) Forestry Policies (South Carolina) < Back Eligibility Agricultural Commercial Program Info State South Carolina Program Type Environmental Regulations Provider South Carolina Forest Commission South Carolina's Forestry industry is one of the largest contributors to the State's economy. Wood residues, among other biomass resources, are used by several co-gen and electricity generators in the state. The South Carolina Forestry Commission manages the State's forest lands: www.state.sc.us/forest/ The South Carolina Biomass Council (http://www.scbiomass.org) was created in 2006 by the South Carolina Energy Office, to increase biomass energy and products in South Carolina. The Energy office issued the report "Biomass Energy Potential in South Carolina", reviewing the technologies and

7

Wood Energy Production Credit | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood Energy Production Credit Wood Energy Production Credit Wood Energy Production Credit < Back Eligibility Commercial Industrial Savings Category Bioenergy Maximum Rebate Credit may be claimed for a period of five years Program Info Start Date 12/30/1998 (most recent revision) State Missouri Program Type Corporate Tax Credit Rebate Amount $5 per ton of processed materials Provider Missouri Department of Natural Resources Note: No new credits are being issued, effective July 1, 2013. This entry is for informational purposes only. The Wood Energy Tax Credit, as effective January 1, 1997, allows individuals or businesses processing Missouri forestry industry residues into fuels an income tax credit of $5.00 per ton of processed material (e.g., wood pellets). A multiplier of 4 applies to charcoal, based on the

8

Forestry | Open Energy Information  

Open Energy Info (EERE)

Facebook icon Twitter icon Forestry Jump to: navigation, search Forestry is "the science of planting and caring for forests and the management of growing timber." References...

9

Forestry Policies (Delaware) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Delaware) Delaware) Forestry Policies (Delaware) < Back Eligibility Commercial Agricultural Program Info State Delaware Program Type Environmental Regulations Provider Agriculture Delaware's forests are managed by the State Forest Service (DFS), within the State Department of Agriculture. In 2010, the Forest Service issued its Resource Assessment and Strategy documents: Delaware Forest Resource Assessment: http://dda.delaware.gov/forestry/061810_DFS_ResourceAssessment.pdf Statewide Forest Strategy: http://dda.delaware.gov/forestry/061810_DFS_Strategy.pdf The Forest Strategy document sets several goals with respect to biomass energy, including an analysis of the resource, developing restrictions on wood energy facilities, promoting a Fuels for Schools program, and developing at least one new market for low-value wood such as bio-energy

10

Assessment of Treated Wood and Alternate Materials for Utility Distribution Poles  

Science Conference Proceedings (OSTI)

This report provides salient facts about common and potential alternative wood pole preservatives and common and potential alternative wood pole materials for use in the electrical distribution setting. Relevant organizations are also discussed. The report presents a brief history of the development and use of each preservative and pole material. It characterizes, qualifies, and quantifies (where possible) the potential impacts of shifts from common preservatives to alternative preservatives and from sou...

2010-10-11T23:59:59.000Z

11

China: Changing Wood Products Markets  

E-Print Network (OSTI)

#12;China: Changing Wood Products Markets less is probably known about the forestry and wood products market in China than most other U.S. trading partners. In the 1980s China emerged as the world,11,12). However, U.S. wood products exports to China declined nearly 93 percent from 1988 to 1996, from $-I%3

Zhang, Daowei

12

Forestry Policies (Oklahoma)  

Energy.gov (U.S. Department of Energy (DOE))

Oklahoma's forests are managed by the Oklahoma Forestry Services, a division of the Oklahoma Department of Agriculture, Food, and Forestry. In 2008 the Department issued the "Forest Resources of...

13

Forestry Policies (Georgia)  

Energy.gov (U.S. Department of Energy (DOE))

Georgia's Forests are managed by the Georgia Forestry Commission. In 2009 the Commission completed a statewide assessment of biomass resources:

14

Forestry Policies (Ohio)  

Energy.gov (U.S. Department of Energy (DOE))

Ohio's Forests are managed by the Department of Natural Resource, Division of Forestry. In 2010 Ohio issued its Statewide Forest Resource Assessment, including discussion of forest resources with...

15

Forestry Policies (New Mexico) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Forestry Policies (New Mexico) Forestry Policies (New Mexico) Forestry Policies (New Mexico) < Back Eligibility Agricultural Commercial Developer Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State New Mexico Program Type Environmental Regulations Provider New Mexico Energy, Minerals and Natural Resources Department New Mexico's forests are managed by the State Forestry Department, within the New Mexico Energy, Minerals, and Natural Resources Department. In 2010 the Department issued the New Mexico Statewide Natural Resources Assessment and Strategy and Response Plans, including discussion of potential for biomass energy from forest biomass: http://www.emnrd.state.nm.us/SFD/documents/New_MexicoNatural_ResourceAss... New Mexico offers the Biomass Equipment and Materials Compensating Tax

16

Forestry Policies (Pennsylvania)  

Energy.gov (U.S. Department of Energy (DOE))

Pennsylvania has over 17 million acres of forests, managed by the State Department of Conservation and Natural Resources, Bureau of Forestry. The Department issued in 2010 its Strategic Plan ...

17

Forestry Policies (Iowa)  

Energy.gov (U.S. Department of Energy (DOE))

Iowa has over 3 million acres of forested land, managed by the State Department of Natural Resources, Forestry Bureau. Iowa forests are summarized in DNR's 2010 Assessment "Iowa's Forests Today":...

18

Forestry Policies (Kansas)  

Energy.gov (U.S. Department of Energy (DOE))

Kansas is home to an established forestry industry managing roughly 2 million acres of land. The vast majority of these lands are privately owned. The Kansas Forest Service (KFS) provides the...

19

Forestry Policies (Nebraska) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Nebraska) Nebraska) Forestry Policies (Nebraska) < Back Eligibility Agricultural Commercial Program Info State Nebraska Program Type Environmental Regulations Provider Nebraska Forest Service Nebraska is home to a state and national forest and a reasonable acreage of planted forests. These lands are managed by the Nebraska Forest Service, operating within the University of Nebraska Lincoln: http://www.nfs.unl.edu/ The NFS provides a number of resources for the use of wood waste for energy generation. The 2008 Wood Waste Supply and Utilization Assessment identified a significant wood waste resource in the state: http://www.nfs.unl.edu/graphics/traditional%20forest%20products/Nebraska... A more recent document identifies current users of forest woody biomass together with economic analysis of their fuel savings:

20

Chemical Pretreatment And Enzymatic Hydrolysis Of Mixed Source-Separated Organic (SSO) And Wood Waste.  

E-Print Network (OSTI)

??This paper examines the effectiveness of two pretreatments on Source-Separated Organic waste (SSO) mixed with wood wastes: long term lime for SSO mixed with forestry… (more)

Faye, Michael

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

New Forestry Commission District Office The new Forestry Commission  

E-Print Network (OSTI)

New Forestry Commission District Office The new Forestry Commission District office at Smithton in construction The Forestry Commission's District office at Smithton in Inverness, Scotland, covers the national fuel heating system has proved effective during the winter of 2009/10, one of the harshest in 40 years

22

Forestry | OpenEI  

Open Energy Info (EERE)

Forestry Forestry Dataset Summary Description The New Zealand Ministry of Economic Development publishes energy data including many datasets related to electricity. Included here are three datasets: electricity energy balance (2005 - 2009), electricity market snapshot (2009), and market competition statistics (2004 - 2009). Source New Zealand Ministry of Economic Development Date Released Unknown Date Updated July 02nd, 2010 (4 years ago) Keywords Agriculture Commercial electricity demand electricity supply Fishing Forestry Industrial Residential Data application/vnd.ms-excel icon Electricity Energy Balance (2005 - 2009) (xls, 42.5 KiB) application/vnd.ms-excel icon Electricity Market Snapshot (2009) (xls, 49.7 KiB) application/vnd.ms-excel icon Market Competition Statistics (xls, 46.1 KiB)

23

Forestry Policies (District of Columbia)  

Energy.gov (U.S. Department of Energy (DOE))

Forest policy and guidelines in Washington D.C. are focused on urban forestry, and are managed by the District Department of Transportation's Urban Forestry Administration. In 2010 The District...

24

Jordan Woods  

NLE Websites -- All DOE Office Websites (Extended Search)

Jordan Woods Windows and Envelope Materials Group Lawrence Berkeley National Laboratory 1 Cyclotron Road MS 90R2000 Berkeley CA 94720 Office Location: 90-2052C (510) 486-4931...

25

For more information contact the Biomass Energy Centre, (01420) 526197 biomass.centre@forestry.gsi.gov.uk  

E-Print Network (OSTI)

For more information contact the Biomass Energy Centre, (01420) 526197 · biomass woodland supports jobs in the forestry industry. Choosing Logs When choosing wood for burning there are two suppliers are available on the Biomass Energy Centre website (www

26

USAID-Forestry Conflict Management Training | Open Energy Information  

Open Energy Info (EERE)

form form View source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit with form History Facebook icon Twitter icon » USAID-Forestry Conflict Management Training Jump to: navigation, search Tool Summary Name: USAID-Forestry Conflict Management Training Agency/Company /Organization: United States Agency for International Development Sector: Land Focus Area: Forestry Resource Type: Training materials Website: www.rmportal.net/training/collections/collection-conflict-management-t USAID-Forestry Conflict Management Training Screenshot References: Forest Conflict Management[1] Logo: USAID-Forestry Conflict Management Training About "The Online Learning Management System (OLMS) provides a web-based

27

Forestry Commission Scotland 231 Corstorphine Road  

E-Print Network (OSTI)

development - Forestry - Sustainable development - Renewable Energy - Community development - Financial Forestry Sustainable development Renewable Energy Community development Financial management Housing, ethnicity, gender, marital status, religion, sexuality and transgender. #12;Annex 1: FORESTRY COMMISSION

28

Forestry Policies (Massachusetts) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Forestry Policies (Massachusetts) Forestry Policies (Massachusetts) Forestry Policies (Massachusetts) < Back Eligibility Commercial Agricultural Program Info State Massachusetts Program Type Environmental Regulations Provider Department of Conservation and Recreation Massachusetts has over 3 million acres of forested land, almost all private, managed by the Department of Conservation and Recreation Forestry Bureau. The State issued in 2010 its Assessment and Strategy documents, including discussion of the potential for better utilization of forestry residues for energy generation. The Strategies document also mentions proposed legislation in this regard: http://www.mass.gov/dcr/stewardship/forestry/docs/Assessment_of_Forest_R... http://www.mass.gov/dcr/stewardship/forestry/docs/Massachusetts_Forest_R...

29

Exergy analysis of the Chartherm process for energy valorization and material recuperation of chromated copper arsenate (CCA) treated wood waste  

Science Conference Proceedings (OSTI)

The Chartherm process (Thermya, Bordeaux, France) is a thermochemical conversion process to treat chromated copper arsenate (CCA) impregnated wood waste. The process aims at maximum energy valorization and material recuperation by combining the principles of low-temperature slow pyrolysis and distillation in a smart way. The main objective of the exergy analysis presented in this paper is to find the critical points in the Chartherm process where it is necessary to apply some measures in order to reduce exergy consumption and to make energy use more economic and efficient. It is found that the process efficiency can be increased with 2.3-4.2% by using the heat lost by the reactor, implementing a combined heat and power (CHP) system, or recuperating the waste heat from the exhaust gases to preheat the product gas. Furthermore, a comparison between the exergetic performances of a 'chartherisation' reactor and an idealized gasification reactor shows that both reactors destroy about the same amount of exergy (i.e. 3500 kW kg{sub wood}{sup -1}) during thermochemical conversion of CCA-treated wood. However, the Chartherm process possesses additional capabilities with respect to arsenic and tar treatment, as well as the extra benefit of recuperating materials.

Bosmans, A., E-mail: anouk.bosmans@mech.kuleuven.be [Department of Mechanical Engineering, Katholieke Universiteit Leuven, Celestijnenlaan 300A, 3001 Heverlee (Belgium); Auweele, M. Vanden; Govaerts, J.; Helsen, L. [Department of Mechanical Engineering, Katholieke Universiteit Leuven, Celestijnenlaan 300A, 3001 Heverlee (Belgium)

2011-04-15T23:59:59.000Z

30

Before the Senate Agriculture, Nutrition, and Forestry | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Agriculture, Nutrition, and Forestry Before the Senate Agriculture, Nutrition, and Forestry Before the Senate Agriculture, Nutrition, and Forestry By: Richard Newell, Administrator...

31

Forestry Policies (Arkansas) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Arkansas) Arkansas) Forestry Policies (Arkansas) < Back Eligibility Agricultural Commercial Program Info State Arkansas Program Type Environmental Regulations Provider Arkansas Forestry Comission Arkansas' Forests are managed by the Arkansas Forestry Commission. In 2010 the Commission completed the state's Forest Action Plan which comprised both the Forest Resource Assessment and Forest Resource Strategy documents: http://forestry.arkansas.gov/SiteCollectionDocuments/ArkansasForestryCom... http://forestry.arkansas.gov/SiteCollectionDocuments/ArkansasForestResou... The Arkansas Forest Stewardship Program facilitates a number of opportunities for forest landowners, and is intended to be the path forward for any landowner or developer pursuing biomass energy markets.

32

Texas 4-H Forestry Invitational Handbook  

E-Print Network (OSTI)

The Texas 4-H Forestry Invitational is a competitive event on forestry knowledge and skills. This handbook covers the invitational rules, topics and contest exercises. It is both a manual for the invitational and a guide for team development.

Bruton, Derrick

2009-04-05T23:59:59.000Z

33

Use of Wood Energy in the United States –  

E-Print Network (OSTI)

The use of wood for energy – including the burning of solid wood and black liquor from pulping – has been growing at a rate significantly greater than that for all other uses such as lumber, pulp, or particleboard. in the United States, the end of most wood is not lumber or pulp and paper but feed for energy. In 1983, 155. 5 M Mg of wood were used for energy. This could threaten to increase the price of wood for those other uses, or it can stimulate us to seek more creative ways of using untapped wood resources for fuel. on the basis of estimates of heavy wood energy use relative to other uses for wood, and estimates of continuing high costs for fossil fuels, we suggest here the feasibility of meeting the demand for fuelwood through small-scale cooperatives. Such an approach can improve forestry practices and can avoid unduly increasing the cost of wood for other end uses.

John W. Koning; Kenneth E. Skog

1986-01-01T23:59:59.000Z

34

Forestry Policies (Indiana) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Indiana) Indiana) Forestry Policies (Indiana) < Back Eligibility Commercial Agricultural Program Info State Indiana Program Type Environmental Regulations Provider Department of Natural Resources Indiana's forests are managed by the Department of Natural Resources, Division of Forestry. The Department issued in 2008 the State's Strategic Plan: http://www.in.gov/dnr/forestry/files/fo-Forestry-Strategic-Plan-2008-201... The State DNR has also issued the resource inventory document "Woody Biomass Feedstock for the Bioenergy and Bioproducts Industries": http://www.in.gov/dnr/forestry/files/fo-WoodyBiomass_final.pdf The DNR has summarized its harvesting guidelines in the document "Harvesting Biomass: A Guide to Best Management Practices", focused on

35

Forestry Policies (Wisconsin) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

You are here You are here Home » Forestry Policies (Wisconsin) Forestry Policies (Wisconsin) < Back Eligibility Agricultural Commercial Developer Program Info State Wisconsin Program Type Environmental Regulations Provider Wisconsin Forestry Council The State of Wisconsin has nearly 16 million acres of forested lands in the state. The Statewide Forest Plan, completed in 2004, is carried out by the Wisconsin Council on Forestry together with the Wisconsin Department of Natural Resources Division of Forestry. This Plan has been augmented with the Statewide Forest Strategy and Statewide Forest Assessment, both completed in 2010. The Statewide Forestry Strategy includes goals with respect to Energy and Climate Change, in terms of both use of forestry residues for energy as

36

Terrestrial laser scanning for measuring the solid wood volume, including branches, of adult standing trees in the forest environment  

Science Conference Proceedings (OSTI)

This study evaluates the potential of terrestrial laser scanning (TLS) to assess the solid wood volume (i.e., stem and branch diameters of more than 7cm) of adult standing trees in the forest environment. The solid wood volume of 42 trees of different ... Keywords: 3D tree modelling, Forestry, LiDAR, Terrestrial laser scanning, Wood volume

Mathieu Dassot; AuréLie Colin; Philippe Santenoise; Meriem Fournier; ThiéRy Constant

2012-11-01T23:59:59.000Z

37

Forestry Policies (Alabama) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Alabama) Alabama) Forestry Policies (Alabama) < Back Eligibility Agricultural Commercial Program Info State Alabama Program Type Environmental Regulations Provider Alabama Forestry Commission Alabama's Forests are managed by the Alabama Forestry Commission. The Commission has organized biomass market resources including a number of publications with regard to biomass energy opportunities and harvesting in the state: http://www.forestry.state.al.us/biomass_publications.aspx?bv=5&s=0 The "Woody Biomass Energy Opportunities in Alabama" document, issued by the State Forestry Commission, includes discussion of resource availability and markets, as well as reference of grant and tax credit incentive opportunities: http://www.forestry.state.al.us/Biomass/Woody%20Biomass%20Energy%20Oppor...

38

Forestry Policies (Kentucky) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

You are here You are here Home » Forestry Policies (Kentucky) Forestry Policies (Kentucky) < Back Eligibility Agricultural Commercial Developer Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Kentucky Program Type Environmental Regulations Provider Kentucky Department of Natural Resources Kentucky's forests are managed by the State Energy and Environment Cabinet, Department of Natural Resources, Division of Forestry. In 2010 the Division completed its Statewide Assessment of Forest Resources and Strategy: http://forestry.ky.gov/landownerservices/pages/forestlandassessment.aspx The document identifies several goals with respect to forest biomass for energy. The document does not directly create legislation in that regard,

39

Integration of Biodiversity into National Forestry Planning:...  

Open Energy Info (EERE)

of Biodiversity into National Forestry Planning: An Annotated Bibliography of Web-Based Resources, Methods, Experiences, and Case Studies Jump to: navigation, search...

40

Forestry-based Carbon Sequestration Projects in Africa: Potential...  

Open Energy Info (EERE)

Forestry-based Carbon Sequestration Projects in Africa: Potential benefits and challenges Jump to: navigation, search Tool Summary Name: Forestry-based Carbon Sequestration...

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Carbon Offsets for Forestry and Bioenergy: Researching Opportunities...  

Open Energy Info (EERE)

Carbon Offsets for Forestry and Bioenergy: Researching Opportunities for Poor Rural Communities Jump to: navigation, search Name Carbon Offsets for Forestry and Bioenergy:...

42

Wood Inspection by Infrared Thermography  

E-Print Network (OSTI)

Wood is used everywhere and for everything. With times, this material presents many adulterations, witch degrade his physical properties. This work present a study of infrared thermography NDT for wood decay detection. The study is based on the difference of moisture content between sound wood and decay. In the first part, moisture content influence on response signal is determine. The second part define the limits of infrared thermography for wood decay detection. Results show that this method could be used, but with many cautions on depth and size of wood defects.

A. Wyckhuyse; X. Maldague; X. Maldague Corresponding

2002-01-01T23:59:59.000Z

43

Forestry Policies (Minnesota) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Minnesota) Minnesota) Forestry Policies (Minnesota) < Back Eligibility Agricultural Commercial Program Info State Minnesota Program Type Environmental Regulations Provider Department of Natural Resources Minnesota's forests are managed through the Department of Natural Resources Division of Forestry. The DNR has several programs and services intended to promote the sustainable use of woody biomass: http://www.dnr.state.mn.us/forestry/biomass/index.html http://www.dnr.state.mn.us/forestry/biomass/resources.html Minnesota was the first state to develop biomass harvesting guidelines to manage the removal of woody biomass at forest operations sites. These guidelines are mandatory on all state lands and many private lands as well: http://files.dnr.state.mn.us/forestry/biomass/biomassHarvestingGuideline...

44

Forestry Policies (Virginia) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Virginia) Virginia) Forestry Policies (Virginia) < Back Eligibility Agricultural Commercial Developer Savings Category Solar Buying & Making Electricity Wind Program Info State Virginia Program Type Environmental Regulations Provider Virginia Department of Forestry Virginia's forests are managed by the Virginia Department of Forestry. In 2010 the Department issued its Statewide Assessment of Forest Resources and Strategic Plan documents: http://www.dof.virginia.gov/info/print/2010-State-Assessment.pdf http://www.dof.virginia.gov/info/print/2010-Strategic-Plan.pdf The Department has also issued a concise reference of the State Forestry Laws: http://www.dof.virginia.gov/resources/pub-2005-Va-Forestry-Laws.pdf State incentives for forest biomass energy are currently limited to the

45

Tropical forestry practices for carbon sequestration  

E-Print Network (OSTI)

Carbon sequestration through forestry has the potential to play a significant role in ameliorating global environmental problems such as atmospheric accumulation of GHG's and climate change. This chapter provides an overview of various aspects related to carbon sequestration through forestry. It describes the main concepts of carbon fixation; the trends in global environmental policy are discussed; different forestry practices are listed; examples of existing projects are given; and finally, a case study of a carbon sequestration project in Malaysia is described. The paper also discusses issues related to the quantification of carbon sequestration potential of different forestry options. This section was included with the intention of specifically highlighting some problems related to commercial transactions for carbon sequestration. Key words: carbon sequestration, CO2 offset, tropical forestry, dipterocarps.

Pedro Moura-costa; Innoprise-face Foundation

1996-01-01T23:59:59.000Z

46

Forestry Policies (Louisiana) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Louisiana) Louisiana) Forestry Policies (Louisiana) < Back Eligibility Agricultural Commercial Developer Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Louisiana Program Type Environmental Regulations Provider Louisiana Department of Agriculture and Forestry Louisiana's Forests are managed by the Louisiana Department of Agriculture and Forestry. In 2010 the Department issued the Statewide Forest Resource Assessment and Strategy. The report identifies the harvesting of forestry residues for biomass energy as an untapped resource with great potential, and recognized Louisiana as an ideal location to develop biomass energy: http://webshare.ldaf.state.la.us/gis/State%20Assessment/Louisiana%20Stat... The document also states the goal of the Louisiana Office of Forestry to

47

Forestry Policies (Montana) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Forestry Policies (Montana) Forestry Policies (Montana) Forestry Policies (Montana) < Back Eligibility Agricultural Commercial Program Info State Montana Program Type Environmental Regulations Provider Department of Natural Resources and Conservation Montana has over 20 million acres of public and private forested lands, about a quarter of the state's land area. Montana's Forests are managed by the Department of Natural Resources and Conservation's Forestry Division. The DNRC's 2010 Statewide Forest Resource Strategy document specifies the promotion and facilitation of forest biomass for energy generation as a key strategic goal: http://dnrc.mt.gov/Forestry/Assistance/Documents/SAResponseStrategy2010.pdf The DNRC also offers financial assistance under its Woody Biomass Utilization program, with a mission to promote the beneficial use of forest

48

Forestry Policies (Tennessee) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Forestry Policies (Tennessee) Forestry Policies (Tennessee) Forestry Policies (Tennessee) < Back Eligibility Agricultural Commercial Developer Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State Tennessee Program Type Environmental Regulations Provider Tennessee Department of Agriculture Tennessee's forests are managed by the Department of Agriculture, Forestry Division. In 2010 the Division issued its Statewide Forest Action Plan, which includes a section detailing the bio-energy and biofuels potential and goals for the state, and quantifies among other things the potential energy from forest biomass: http://www.tn.gov/agriculture/publications/forestry/TN-FAP.pdf The document also specifies the goal of expanding markets for biomass forest products, to address several different issues including decline in

49

Forestry Policies (Connecticut) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Connecticut) Connecticut) Forestry Policies (Connecticut) < Back Eligibility Agricultural Commercial Program Info State Connecticut Program Type Environmental Regulations Provider Department of Energy and Environmental Protection The state of Connecticut is home to a large area of productive forested lands. These forests are managed primarily by the Division of Forestry, under the State Department of Energy and Environmental Protection (DEEP). In 2010, The State issued its Forest Resource Assessment and Strategy document: http://www.ct.gov/dep/lib/dep/forestry/assessment_and_strategy/assessmen... The Resource Assessment and Strategy document discusses a proposed Harvesting Guidelines study that is still under development, in the interim the State is considering using the Forest Guild Northeast Region's

50

Forestry Policies (New Jersey) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

New Jersey) New Jersey) Forestry Policies (New Jersey) < Back Eligibility Agricultural Commercial Program Info State New Jersey Program Type Environmental Regulations Provider Department of Environmental Protection New Jersey Forests are managed by the Department of Environmental Protection, Division of Parks and Forestry, New Jersey Forestry Services. In 2010 the State issued its Forest Action Plan, including some mention of forestry residues as biomass fuel: http://www.stateforesters.org/files/NJ-Assess-Strategy-20100810.pdf In 2011 The New Jersey Board of Public Utilities commissioned a report by the Biomass Work Group (BWG) titled "Biomass Resources for Producing Renewable Power and Fuels in the State of New Jersey and Incentives to Promote Their Development":

51

Forestry Policies (South Dakota) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

South Dakota) South Dakota) Forestry Policies (South Dakota) < Back Eligibility Agricultural Commercial Program Info State South Dakota Program Type Environmental Regulations Provider Department of Agriculture South Dakota's forests are managed by the Department of Agriculture, Conservation and Forestry Division. Forests comprise around 1.7 million acres of land in the State. In the 2010 Forest Strategy document, underutilization of woody biomass is identified as a key threat to the industry. The document proposes incentives to public government building project to convert to biomass boilers: http://sdda.sd.gov/legacydocs/Forestry/educational-information/PDF/rsi21... In 2005 the State conducted a feasibility study of biomass fuel for heating schools, using locally sourced forestry residues:

52

Global climate change: Some implications, opportunities, and challenges for US forestry  

SciTech Connect

It is widely agreed that the concentration of greenhouse gases in the earth's atmosphere is increasing, that this increase is a consequence of man's activities, and that there is significant risk that this will lead to changes in the earth's climate. The question is now being discussed what, if anything, we should be doing to minimize and/or adapt to changes in climate. Virtually every statement on this matter; from the US Office of Technology Assessment, to the National Academy of Science, to the Nairobi Declaration on Climatic Change, includes some recommendation for planting and protecting forests. In fact, forestry is intimately involved in the climate change debate for several reasons: changing climate patterns will affect existing forests, tropical deforestation is one of the major sources of greenhouse gases to the atmosphere, reforestation projects could remove additional carbon dioxide from the atmosphere and there is renewed interest in wood-based or other renewable fuels to replace fossil fuels. Part of the enthusiasm for forestry-related strategies in a greenhouse context is the perception that forests not only provide greenhouse benefits but also serve other desirable social objectives. This discussion will explore the current range of thinking in this area and try to stimulate additional thinking on the rationality of the forestry-based approaches and the challenges posed for US forestry.

Marland, G.

1991-01-01T23:59:59.000Z

53

WOOD PRODUCTS 1. INTRODUCTION TO WARM AND WOOD PRODUCTS  

E-Print Network (OSTI)

This chapter describes the methodology used in EPA’s Waste Reduction Model (WARM) to estimate streamlined life-cycle greenhouse gas (GHG) emission factors for wood products beginning at the point of waste generation. The WARM GHG emission factors are used to compare the net emissions associated with wood products in the following four materials management alternatives: source

unknown authors

2012-01-01T23:59:59.000Z

54

GLOBAL WOOD SUPPLY Sten Nilsson  

E-Print Network (OSTI)

· Increasing demand for wood through population and economic growth · More expensive wood · Where should America Expansion potential USA Deficit Canada Deficit #12;RUSSIA Advantages: Raw Materials Source LEAVED ­ EASTERN USA Source: http://www.cas.vanderbilt.edu/bioimages/biohires/ecoregions/h50404bottomland

55

Drew Wood  

NLE Websites -- All DOE Office Websites (Extended Search)

Wood Indoor Air Quality Research Collaborative drew@iaqrc.org This speaker was a visiting speaker who delivered a talk or talks on the date(s) shown at the links below. This...

56

Forestry Policies (Michigan) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

You are here You are here Home » Forestry Policies (Michigan) Forestry Policies (Michigan) < Back Eligibility Agricultural Commercial Program Info State Michigan Program Type Environmental Regulations Provider Department of Natural Resources Michigan's 19 million acres of forests are managed by the Department of Natural Resources, Forestry and Water Division. The Department issued its Forest Resource Assessment and Strategy document in 2010: http://www.michigan.gov/documents/dnr/MichiganForestResourceAssessmentan... The document mentions several issues with regard to better utilization of forest woody biomass resources, and the DNR has in the past submitted request for grant proposal to address issues identified in the Assessment and Strategy document: http://www.michigan.gov/documents/dnr/3000NASPFSingleRFP110110_339415_7.pdf

57

Forestry Policies (New York) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Forestry Policies (New York) Forestry Policies (New York) Forestry Policies (New York) < Back Eligibility Commercial Agricultural Program Info State New York Program Type Environmental Regulations Provider Department of Environmental Conservation New York has nearly 19 million acres of forested land, about 63 percent of the states land area. These lands are managed by the State Department of Environmental Conservation. The Department issued its Forest Action Plan in 2010, which includes discussion of sustainable markets and the promotion of forest products for energy uses by focusing on technical assistance, favorable policies and incentives: http://www.dec.ny.gov/docs/lands_forests_pdf/fras070110.pdf The Department provides directory for timber and mill residue users: http://www.dec.ny.gov/lands/46935.html

58

Integration of Biodiversity into National Forestry Planning: An Annotated  

Open Energy Info (EERE)

Integration of Biodiversity into National Forestry Planning: An Annotated Integration of Biodiversity into National Forestry Planning: An Annotated Bibliography of Web-Based Resources, Methods, Experiences, and Case Studies Jump to: navigation, search Tool Summary Name: Integration of Biodiversity into National Forestry Planning: An Annotated Bibliography of Web-Based Resources, Methods, Experiences, and Case Studies Agency/Company /Organization: Center for International Forestry Research Partner: United Nations Environment Programme, Global Environment Facility Sector: Land Focus Area: Forestry Resource Type: Lessons learned/best practices Website: www.unep.org/bpsp/forestry/forestry%20annotated%20bibliography/annotat References: Integration of Biodiversity into National Forestry Planning: An Annotated Bibliography of Web-Based Resources, Methods, Experiences, and Case Studies[1]

59

Forestry Policies (Illinois) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Illinois) Illinois) Forestry Policies (Illinois) < Back Eligibility Agricultural Commercial Program Info State Illinois Program Type Environmental Regulations Provider Department of Natural Resources Illinois' Forests are managed by the State Department of Natural Resources, Division of Forest Resources. The Department issued in 2008 its "Statewide Forest Resource Assessments and Strategies" document: http://www.stateforesters.org/files/IL-Assess-Strategy-20100528.pdf The Illinois Forestry Development Act (IFDA) offers financial incentive for implementing forest management practices that would protect and enhance forest resources. It provides the funding source for a forest landowner cost-share program. This program is funded through the collection of a four

60

CONTACT LIST FOR THE DEPARTMENT OF FORESTRY AND NATURAL RESOURCES  

E-Print Network (OSTI)

Greenville 864-232-4431 x123 jaime OPEN Forestry & Natural Resources Newberry 803-276-1091 x112 Stephen

Bolding, M. Chad

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Our Purpose and Direction Forestry Commission Wales  

E-Print Network (OSTI)

Corporate Our Purpose and Direction Forestry Commission Wales: Corporate Plan 2012 to 2015 #12;Ministers Foreword I am very pleased to be providing the foreword for `Our purpose and direction beyond the 50-year lifespan of Woodlands for Wales. Our Purpose and Direction John Griffiths AM Minister

62

F 230 -2012 Forestry Field Measurements  

E-Print Network (OSTI)

been processed first). F230 Estimated Costs for Summer 2012 Resident Non-resident Tuition (minus COF and picking up an Override Form. 2) Take Override form to Forestry 123 and get it processed. 3) IMPORTANT are charged for your NR220 lodging. Prior to arrival at Pingree, you will need to purchase the equipment

63

Burning Forest Residues231 Corstorphine Road www.forestry.gov.uk  

E-Print Network (OSTI)

1 Burning Forest Residues231 Corstorphine Road Edinburgh EH12 7AT www.forestry.gov.uk S E P T E M B E R 2 0 0 2 FCTN004 SUMMARY Burning forest residues is a traditional method of ground clearance following harvesting operations. Guidance is given on suitable types of cut material for burning, equipment

64

Mitigation Options in Forestry, Land-Use, Change and Biomass Burning in Africa  

DOE Green Energy (OSTI)

Mitigation options to reduce greenhouse gas emissions and sequester carbon in land use sectors are describe in some detail. The paper highlights those options in the forestry sector, which are more relevant to different parts of Africa. It briefly outlines a bottom-up methodological framework for comprehensively assessing mitigation options in land use sectors. This method emphasizes the application of end-use demand projections to construct a baseline and mitigation scenarios and explicitly addresses the carbon storage potential on land and in wood products, as well as use of wood to substitute for fossil fuels. Cost-effectiveness indicators for ranking mitigation options are proposed, including those, which account for non-carbon monetary benefits such as those derived from forest products, as well as opportunity cost of pursuing specific mitigation option. The paper finally surveys the likely policies, barriers and incentives to implement such mitigation options in African countries .

Makundi, Willy R.

1998-06-01T23:59:59.000Z

65

Wood Fired Steam Plants in Georgia  

E-Print Network (OSTI)

During the 1970's, Georgia industry experienced problems obtaining fuel for operations on several occasions. In particular, the very cold winter of 1976-77 resulted in natural gas curtailments which virtually shut down many of Georgia's industries. Shortly after that time, Georgia Tech and the Georgia Forestry Commission embarked on a number of projects directed toward providing the use of wood as an industrial energy source. This paper will present an overview of these programs with an emphasis on three demonstration plants that were built with partial financing by state and federal government.

Bulpitt, W. S.

1983-01-01T23:59:59.000Z

66

Alternative Fuels Data Center: Agriculture and Forestry Biofuel Production  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Agriculture and Agriculture and Forestry Biofuel Production Grants to someone by E-mail Share Alternative Fuels Data Center: Agriculture and Forestry Biofuel Production Grants on Facebook Tweet about Alternative Fuels Data Center: Agriculture and Forestry Biofuel Production Grants on Twitter Bookmark Alternative Fuels Data Center: Agriculture and Forestry Biofuel Production Grants on Google Bookmark Alternative Fuels Data Center: Agriculture and Forestry Biofuel Production Grants on Delicious Rank Alternative Fuels Data Center: Agriculture and Forestry Biofuel Production Grants on Digg Find More places to share Alternative Fuels Data Center: Agriculture and Forestry Biofuel Production Grants on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type

67

Woodfuel community heating at Kielder A wood-fired district heating  

E-Print Network (OSTI)

Woodfuel community heating at Kielder A wood-fired district heating system, one of the first of its-fired district heating system was installed in 2004 as a practical low-carbon solution to providing heat and hot 2010. Contact for further information: Graham Gill (graham.gill@forestry.gsi.gov.uk) District heating

68

The potential for Eucalyptus as a wood fuel in the UK A.D. Leslie a,  

E-Print Network (OSTI)

The potential for Eucalyptus as a wood fuel in the UK A.D. Leslie a, , M. Mencuccini b,1 , M. Perks for utilising woody biomass, grown under short rotation forestry management systems, to produce electricity or heat. There are benefits to using biomass in generating heat and power the main environmental benefit

Mencuccini, Maurizio

69

Forestry Policies (New Hampshire) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

New Hampshire) New Hampshire) Forestry Policies (New Hampshire) < Back Eligibility Commercial Agricultural Program Info State New Hampshire Program Type Environmental Regulations Provider Department of Resources and Economic Development New Hampshire's forests are managed by the Department of Resources and Economic Development, Division of Forests and Lands. The Department issued in 2010 its Statewide Assessment and Strategies documents: http://www.nhdfl.org/library/pdf/Planning/NH%20Statewide%20Assessment%20... http://www.nhdfl.org/library/pdf/Planning/NH%20Forest%20Resource%20Strat... The Strategy document identifies the goal to "optimize availability of biomass for electricity and heating within sustainable limits", as originally recommended in the 2008 Agriculture, Forestry and Waste Action

70

Forestry Policies (Texas) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Texas) Texas) Forestry Policies (Texas) < Back Eligibility Agricultural Commercial Program Info State Texas Program Type Environmental Regulations Provider Texas A&M Forest Service Texas' forested lands are managed by the Texas Forest Service, a division of Texas A&M University. TFS has issued the "Statewide Assessment of Forest Resources", which includes discussion of the opportunity for utilizing woody biomass from forestry operations: http://txforestservice.tamu.edu/uploadedFiles/Sustainable/assessment/Tex... In 2008, the TFS issued a document titled "Estimation of Woody Biomass Availability for Energy in Texas", a study mandated by Texas House Bill 1090: http://txforestservice.tamu.edu/uploadedFiles/Sustainable/econdev/27192_... The Texas State Energy Conservation Office offers information on biomass

71

Life in the woods : production and consumption of the urban forest  

E-Print Network (OSTI)

The use of wood is fraught with paradox. Wood as a building material is embraced for its naturalness, while the cutting of trees is indicted as a destruction of nature. Wood is lauded for its structural properties and ...

Volicer, Nadine (Nadine M.)

2012-01-01T23:59:59.000Z

72

Agriculture, Forestry and Other Land Use Mitigation Project Database | Open  

Open Energy Info (EERE)

Agriculture, Forestry and Other Land Use Mitigation Project Database Agriculture, Forestry and Other Land Use Mitigation Project Database Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Agriculture, Forestry and Other Land Use Mitigation Project Database Agency/Company /Organization: Food and Agriculture Organization of the United Nations Sector: Land Focus Area: Forestry, Agriculture Resource Type: Dataset Website: www.fao.org/climatechange/67148/en/ RelatedTo: Mitigation of Climate Change in Agriculture (MICCA) Project Agriculture, Forestry and Other Land Use Mitigation Project Database Screenshot References: AFOLU Mitigation Database[1] Global Survey of Agricultural Mitigation Projects Paper[2] "The AFOLU MP database endeavors to gather information on all mitigation activities currently ongoing within the agricultural and forestry sectors

73

Global Timber Market and Forestry Data Project | Open Energy Information  

Open Energy Info (EERE)

Global Timber Market and Forestry Data Project Global Timber Market and Forestry Data Project Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Global Timber Market and Forestry Data Project Agency/Company /Organization: Ohio State University Sector: Land Focus Area: Forestry Topics: Market analysis, Resource assessment Resource Type: Dataset Website: aede.osu.edu/people/sohngen.1/forests/GTM/index.htm Global Timber Market and Forestry Data Project Screenshot References: Global Timber Market and Forestry Data Project[1] About "This website provides data on global forest resources and timber markets. The purpose of this data is to help modelers advance understanding about the important role that forests play in the global ecosystem and the effects that markets have on these resources. The data can be used by

74

A study of the molecular mechanics of wood cell walls  

E-Print Network (OSTI)

Wood is the original structural material, developed by nature to support tall plants. Every advantageous feature of wood as used in artificial structures is rooted in the plant's evolved capability to withstand the conditions ...

Adler, David, S.M. (David C.). Massachusetts Institute of Technology

2013-01-01T23:59:59.000Z

75

STOICHIOMETRY OF WOOD LIQUEFACTION  

E-Print Network (OSTI)

co 2 By decomposition to (2) - 0 in H cf 0 in wood TABLE VForced Balance - Wood to Char Output - 55 lbs char lbsuc -61 STOICHIOMETRY OF WOOD LIQUEFACTION Hubert G. Davis

Davis, Hubert G.

2013-01-01T23:59:59.000Z

76

Valorisation of forestry waste by pyrolysis in an auger reactor  

SciTech Connect

Pyrolysis of forestry waste has been carried out in an auger reactor to study the influence of operational variables on the reactor performance and the properties of the related products. Pine woodchips were used for the first time as raw material and fed continuously into the reactor. Ten experiments were carried out under inert atmosphere at: (i) different reaction temperature (1073, 973, 873, 823 and 773 K); (ii) different solid residence time (5, 3, 2 and 1.5 min); and (iii) different biomass flow rate (3.9, 4.8 and 6.9 kg/h). Results show that the greatest yields for liquid production (59%) and optimum product characterisation were obtained at the lowest temperature studied (773 K) and applying solid residence times longer than 2 min. Regarding bio-oil properties, GC/MS qualitative identification show that the most abundant compounds are volatile polar compounds, phenols and benzenediols; and very few differences can be observed among the samples regardless of the pyrolysis operating conditions. On the whole, experimental results demonstrate that complete reaction of forest woodchips can be achieved in an auger reactor in most of the experimental conditions tested. Moreover, this study presents the initial steps for the future scaling up of the auger reactor with the aim of converting it into a mobile plant which will be able to remotely process biomass such as energy crops, forestry and agricultural wastes to obtain bio-oil that, in turn, can be used as energy vector to avoid high transport costs.

Puy, Neus, E-mail: neus.puy@uab.cat [Institute of Environmental Science and Technology (ICTA), Universitat Autonoma de Barcelona, Edifici Cn - Campus de la UAB, 08193 Cerdanyola del Valles, Barcelona (Spain); Murillo, Ramon; Navarro, Maria V.; Lopez, Jose M. [Instituto de Carboquimica, CSIC, M Luesma Castan 4, 50018 Zaragoza (Spain); Rieradevall, Joan [Institute of Environmental Science and Technology (ICTA), Universitat Autonoma de Barcelona, Edifici Cn - Campus de la UAB, 08193 Cerdanyola del Valles, Barcelona (Spain); Department of Chemical Engineering, Universitat Autonoma de Barcelona, ETSE, Campus de la UAB, 08193 Cerdanyola del Valles, Barcelona (Spain); Fowler, G. [Department of Civil and Environmental Engineering, Imperial College London, South Kensington Campus, London SW7 2AZ (United Kingdom); Aranguren, Ignacio; Garcia, Tomas [Instituto de Carboquimica, CSIC, M Luesma Castan 4, 50018 Zaragoza (Spain); Bartroli, Jordi [Department of Chemistry, Universitat Autonoma de Barcelona, Edifici Cn - Campus de la UAB, 08193 Cerdanyola del Valles, Barcelona (Spain); Mastral, Ana M. [Instituto de Carboquimica, CSIC, M Luesma Castan 4, 50018 Zaragoza (Spain)

2011-06-15T23:59:59.000Z

77

Carbon Offsets for Forestry and Bioenergy: Researching Opportunities for  

Open Energy Info (EERE)

Carbon Offsets for Forestry and Bioenergy: Researching Opportunities for Carbon Offsets for Forestry and Bioenergy: Researching Opportunities for Poor Rural Communities Jump to: navigation, search Name Carbon Offsets for Forestry and Bioenergy: Researching Opportunities for Poor Rural Communities Agency/Company /Organization Overseas Development Institute Sector Energy, Land Focus Area Renewable Energy, Biomass, Forestry Topics Policies/deployment programs, Background analysis Resource Type Publications Website http://www.odi.org.uk/resource Country Uganda, India Eastern Africa, Southern Asia References Carbon Offsets for Forestry and Bioenergy: Researching Opportunities for Poor Rural Communities[1] Summary "This report presents findings from a research study in Uganda and India looking at the opportunities that carbon offset projects offer for poor

78

The purpose of this pack This pack presents the Forestry  

E-Print Network (OSTI)

pellets. (b) Commercial scale wood chip fuelled boiler. (c) Combined heat and power gasifier unit pellet production as fuel for domestic appliances and as a replacement for fossil fuel in some larger suitable for wood pellets. Wood chips and hog fuel: an example High quality wood chips recommended

79

Materials Studio  

Science Conference Proceedings (OSTI)

Jan 14, 2008 ... G. Fitzgerald; G. Goldbeck-Wood; P. Kung; M. Petersen; L. Subramanian; J. Wescott, " Materials Modeling from Quantum Mechanics to The ...

80

Uses and Desirable Properties of Wood in the 21st Century  

E-Print Network (OSTI)

of commercial de- velopment is use of wood pellet fuel to pro- duce heat or electric power. Wood pellets for the pellet Figure 2. Global production of paper and paperboard and wood panels by principal (continental, and production of nano-enabled materials and products are expected to increasingly shape wood use as the 21st

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Reducing Forestry Emissions in Indonesia | Open Energy Information  

Open Energy Info (EERE)

Emissions in Indonesia Emissions in Indonesia Jump to: navigation, search Name Reducing Forestry Emissions in Indonesia Agency/Company /Organization Center for International Forestry Research Sector Land Focus Area Forestry Topics Implementation, Policies/deployment programs, Pathways analysis, Background analysis Resource Type Guide/manual Website http://prod-http-80-800498448. Country Indonesia UN Region South-Eastern Asia References Reducing Forestry Emissions in Indonesia[1] Overview "In this paper, we look critically at the trade-offs between development pathways based on land-intensive enterprises and climate change mitigation. Without a coordinated approach to multiple objectives, efforts in one area could undermine efforts in the other. For example, potential major

82

A Real-Time Weather System for Forestry  

Science Conference Proceedings (OSTI)

The Forestry Weather Interpretations System (FWIS) has been pilot-tested in 12 southern states from Virginia to Texas for two years. Hourly surface observational data from airport locations, upper-air soundings, and Georgia forecast data, entered ...

James T. Paul

1981-10-01T23:59:59.000Z

83

Forestry-based Carbon Sequestration Projects in Africa: Potential benefits  

Open Energy Info (EERE)

Forestry-based Carbon Sequestration Projects in Africa: Potential benefits Forestry-based Carbon Sequestration Projects in Africa: Potential benefits and challenges Jump to: navigation, search Tool Summary Name: Forestry-based Carbon Sequestration Projects in Africa: Potential benefits and challenges Agency/Company /Organization: Natural Resources Forum Sector: Land Focus Area: Forestry Topics: Implementation, GHG inventory, Resource assessment Resource Type: Publications, Lessons learned/best practices, Case studies/examples Website: www.worldagroforestry.org/downloads/publications/PDFs/JA08145.PDF UN Region: "Sub-Saharan Africa" is not in the list of possible values (Eastern Africa, Middle Africa, Northern Africa, Southern Africa, Western Africa, Caribbean, Central America, South America, Northern America, Central Asia, Eastern Asia, Southern Asia, South-Eastern Asia, Western Asia, Eastern Europe, Northern Europe, Southern Europe, Western Europe, Australia and New Zealand, Melanesia, Micronesia, Polynesia, Latin America and the Caribbean) for this property.

84

Wood Use Across Time  

E-Print Network (OSTI)

?Forest products history and use ?Forest resource- the big picture ?Consumption- the big picture ?Trends forest products industry ? pulp & paper ? solid woodBack in Time ?1492 ? Columbus sailed the ocean blue! ? wood use- fuelwood American Indians ?1634: Jean Nicolet

Scott Bowe; United States Wood Use

2005-01-01T23:59:59.000Z

85

Residential Wood Residential wood combustion (RWC) is  

E-Print Network (OSTI)

Residential Wood Combustion Residential wood combustion (RWC) is increasing in Europe because PM2.5. Furthermore, other combustion- related sources of OA in Europe may need to be reassessed. Will it affect global OA emission estimates? Combustion of biofuels is globally one of the major OA sources

86

Directory of selected tropical forestry journals and newsletters  

SciTech Connect

Heightened public and professional interest in tropical forestry has led in recent years to a large increase in the volume of information produced on the subject. The directory catalogues and describes 473 tropical forestry periodicals, ranging from scientific journals to informal newsletters. Entries are arranged alphabetically and provide information on each journals focus, audience, language, frequency of publication, availability, and cost, as well as address, and telephone, fax, and telex number. Includes subject, geographic, and language indexes.

Haugen, C.; Durst, P.B.; Freed, E.

1994-01-01T23:59:59.000Z

87

Performance oriented packaging testing of nine Mk 3 Mod 0 signal containers in PPP-B-621 wood box for packing group II solid hazardous materials. Final report  

SciTech Connect

A PPP-B-621 wood box containing nine Mk 3 Mod 0 Signal containers was tested for conformance to Performance Oriented Packaging criteria established by Code of Federal Regulations Title 49 CFR. The container was tested with a gross weight of 123.3 pounds (56 kilograms) and met all requirements.

Libbert, K.J.

1992-10-01T23:59:59.000Z

88

STEO October 2012 - wood  

U.S. Energy Information Administration (EIA) Indexed Site

More U.S. households burning wood this winter to stay warm, More U.S. households burning wood this winter to stay warm, reversing two-decade decline Burning wood as the primary heating source in U.S. households has risen over the last 10 years, reversing the decline seen in the 1980s and 1990s. About 2.6 million households out of 115 million will rely on wood as the main way to warm their homes this winter. That's up 3 percent from last year, according to the U.S. Energy Information Administration's new winter fuels forecast. The West will have the most households using wood as their primary space heating fuel, followed by the Midwest, South and Northeast regions of the United States. Wood is also the second most common backup fuel, after electricity, that households across the U.S. use as a supplemental heating source. Almost half of all rural households use wood this

89

Good Practice Guidance on the Sustainable Mobilisation of Wood in Europe |  

Open Energy Info (EERE)

Good Practice Guidance on the Sustainable Mobilisation of Wood in Europe Good Practice Guidance on the Sustainable Mobilisation of Wood in Europe Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Good Practice Guidance on the Sustainable Mobilisation of Wood in Europe Agency/Company /Organization: United Nations Economic Commission for Europe Partner: Food and Agriculture Organization of the United Nations Sector: Land Focus Area: Biomass, Forestry Topics: Implementation, Policies/deployment programs Resource Type: Guide/manual, Lessons learned/best practices Website: www.unece.org/publications/oes/Timber_wood-mobilization-good_practice- UN Region: "Western & Eastern Europe" is not in the list of possible values (Eastern Africa, Middle Africa, Northern Africa, Southern Africa, Western Africa, Caribbean, Central America, South America, Northern America, Central Asia, Eastern Asia, Southern Asia, South-Eastern Asia, Western Asia, Eastern Europe, Northern Europe, Southern Europe, Western Europe, Australia and New Zealand, Melanesia, Micronesia, Polynesia, Latin America and the Caribbean) for this property.

90

Solvolytic liquefaction of wood under mild conditions  

DOE Green Energy (OSTI)

Conversion of wood to liquid products requires cleavage of bonds which crosslink the wood structure. This study examines a low-severity wood solubilization process utilizing a solvent medium consisting of a small amount of sulfuric acid and a potentially wood-derivable alcohol. In one half hour of reaction time at 250/sup 0/C under 15 psia starting nitrogen pressure, over 95% of the wood (maf) was rendered acetone-soluble. The product is a soft, black, bitumen-like solid at room temperature but readily softens at 140/sup 0/C. Between 25 and 50% of the original wood oxygen, depending on alcohol used, was removed as water. Approximately 2 to 17% of the alcohols were retained in the product. Gel permeation chromatography showed that the product's median molecular weight is around 300. Based on experimental and literature results, a mechanism for wood solubilization is proposed. This involves protonation of the etheric oxygen atoms, leading to subsequent bond scission to form carbonium ions which are stabilized by solvent alkoxylation. At severe conditions, polymerization and condensation reactions result in acetone-insoluble materials.

Yu, S.M.

1982-04-01T23:59:59.000Z

91

Urban Wood Waste Resource Assessment  

DOE Green Energy (OSTI)

This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris.

Wiltsee, G.

1998-11-20T23:59:59.000Z

92

Wood pellet production  

Science Conference Proceedings (OSTI)

Southern Energy Limited's wood pellet refinery, Bristol, Florida, produces wood pellets for fuel from scrap wood from a nearby sawmill and other hog fuel delivered to the plant from nearby forest lands. The refinery will provide 50,000 tons of pellets per year to the Florida State Hospital at Chattahoochee to fire recently converted boilers in the central power plant. The pellets are densified wood, having a moisture content of about 10% and a heating value of 8000 Btu/lb. They are 0.5 inches in diameter and 2 to 3 inches in length.

Moore, J.W.

1983-08-01T23:59:59.000Z

93

An assessment of management practices of wood and wood-related wastes in the urban environment  

DOE Green Energy (OSTI)

The US Environmental Protection Agency estimates that yard waste{sup 1} accounts for approximately 16% of the municipal solid waste (MSW) stream (US EPA, 1994). Until recently, specific data and related information on this component of the (MSW) stream has been limited. The purposes of this study, phase two of the three-phase assessment of urban wood waste issues, are to assess and describe current alternatives to landfills for urban wood waste management; provide guidance on the management of urban wood waste to organizations that produce or manage wood waste; and clarify state regulatory and policy positions affecting these organizations. For this study, urban wood waste is defined as solid waste generated by tree and landscape maintenance services (public and private). Urban wood waste includes the following materials: unchipped mixed wood, unchipped logs, and unchipped tops and brush; clearing and grubbing waste; fall leaves and grass clippings; and chips and whole stumps. Construction and demolition debris and consumer-generated yard waste are not included in this study. Generators of urban wood waste include various organizations; municipal, county, and commercial tree care divisions; nurseries, orchards, and golf courses; municipal park and recreation departments; and electric and telephone utility power line maintenance, excavator and land clearance, and landscape organizations. (1) US EPA defines yard waste as ''yard trimmings'' which includes ''grass, leaves and tree brush trimmings from residential, institutional, and commercial sources.''

NONE

1996-02-01T23:59:59.000Z

94

HYDROLYZED WOOD SLURRY FLOW MODELING  

E-Print Network (OSTI)

LBL-10090 UC-61 HYDROLYZED WOOD SLURRY FLOW MODELING JimLBL-10090 HYDROLYZED WOOD SLURRY FLOW MODELING Jim Wrathallconversion of hydrolyzed wood slurry to fuel oil, Based on

Wrathall, Jim

2012-01-01T23:59:59.000Z

95

Climate change mitigation through forestry measures: potentials, options, practice  

E-Print Network (OSTI)

is the FC doing? ­ Woodland carbon code and assessment protocols (3 slides) · Conclusions (2 slides). #12 2010 Climate change mitigation and forestry measures Global carbon balance c. 2000 Burning fossil fuels 23.1 GtCO2 yr-1 Land-use change (including deforestation) 5.9 GtCO2 yr -1 Vegetation growth 11.0 Gt

96

Colorado Forestry Advisory Board Members: April 6, 2005  

E-Print Network (OSTI)

and intensity of insect and disease activity continues to be a concern in many forests. Aerial surveys recorded#12;Colorado Forestry Advisory Board Members: April 6, 2005 The 2004 Report on the Health of Colorado's Forests explores the unique issues and chal- lenges of sustaining and managing ponderosa pine

97

Biomass Support for the China Renewable Energy Law: Feasibility Report -- Agricultural and Forestry Solid Wastes Power Generation Demonstration, December 2005  

DOE Green Energy (OSTI)

Subcontractor report on feasibility of using agricultural and forestry wastes for power generation in China

Not Available

2006-10-01T23:59:59.000Z

98

Wood Heating Fuel Exemption  

Energy.gov (U.S. Department of Energy (DOE))

This statute exempts from the state sales tax all wood or "refuse-derived" fuel used for heating purposes. The law does not make any distinctions about whether the qualified fuels are used for...

99

Gregory H. Woods  

Energy.gov (U.S. Department of Energy (DOE))

Gregory H. Woods was sworn in as the General Counsel of the Department of Energy on April 16, 2012, following the unanimous confirmation of his appointment by the United States Senate.  Mr....

100

Gregory H. Woods  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

H. Woods H. Woods Department· of Energy Fermi Site Office Post Office Box 2000 Batavia, Illinois 60510 JAN 1 1 2DD Office of the General Counsel GC-1, FORS SUBJECT: FERMI SITE OFFICE (FSO) 2013 ANNUAL NATIONAL ENVIRONMENTAL POLICY ACT (NEPA) PLANNING SUMMARY Section 5(a) (7) of Department Of Energy Order 451.1 B Change 2, NEPA Compliance Program, requires each Secretarial Officer and Head of Field Organization to submit an annual NEPA

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Finishing Wood Decks  

E-Print Network (OSTI)

Wood decks have become an important part of residential construction in recent years. However, there is considerable confusion regarding how these structures should be protected with finish. This paper summarizes the types, application techniques, and expected service lives of various finishes on both preservative treated and untreated lumber. Recommendations are made on the basis of decades of research on various wood species using a wide variety of finishes.

R. Sam Williams; et al.

1993-01-01T23:59:59.000Z

102

Treated Wood Pole Management  

Science Conference Proceedings (OSTI)

This document characterizes similarities and differences in international wood pole and wood pole preservative management. The research team identified practices for selection, regulation, and disposition of utility poles outside the United States. Most information is based on interviews and website and published literature searches. Additional research will clarify regulatory positions in other countries and generate improved understanding, which will support strategic planning for U.S. utilities. Utili...

2008-10-29T23:59:59.000Z

103

Center for International Forestry Research | Open Energy Information  

Open Energy Info (EERE)

Research Research Jump to: navigation, search Logo: Center for International Forestry Research Name Center for International Forestry Research Address Jalan CIFOR Situ Gede Place Bogor Barat, Indonesia Phone number 62-251-8622-622 Website http://www.cifor.cgiar.org Coordinates -6.558301°, 106.755187° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":-6.558301,"lon":106.755187,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

104

FORESTRY COLORADO WESTERN POWER ADMIN POC Cheryl Drake Telephone  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FORESTRY FORESTRY COLORADO WESTERN POWER ADMIN POC Cheryl Drake Telephone (720) 962-7154 Email drake@wapa.gov Timber tract operations 113110 Cutting and transporting timber 113310 GEORGIA SOUTHEASTERN POWER ADMIN POC Ann Craft Telephone (706) 213-3823 Email annc@sepa.doe.gov Timber tract operations 113110 Cutting and transporting timber 113310 NEW MEXICO NNSA SERVICE CENTER POC Gregory Gonzales Telephone (505) 845-5420 Email ggonzales@doeal.gov Timber tract operations 113110 Cutting and transporting timber 113310 OHIO EM BUSINESS CENTER POC Karen Bahan Telephone (513) 246-0555 Email karen.bahan@emcbc.doe.gov Timber tract operations 113110 Cutting and transporting timber 113310 OKLAHOMA SOUTHWESTERN POWER ADMIN POC Gary Bridges Telephone (918) 595-6671 Email gary.bridges@swpa.gov Timber tract operations 113110

105

Principle Wood Scientist  

E-Print Network (OSTI)

Wood, bark, and the wax-coated seeds from Chinese tallow tree (Sapium sebiferum (L.) Roxb. syn. Triadica sebifera (L.) Small), an invasive tree species in the southeastern United States, were subjected to extractions and degradative chemical analyses in an effort to better understand the mechanism(s) by which this tree species aggressively competes against native vegetation, and also to facilitate utilization efforts. Analysis of the wood extractives by FTIR spectroscopy showed functionalities analogous to those in hydrolyzable tannins, which appeared to be abundant in the bark; as expected, the seeds had a high wax/oil content (43.1%). Compared to other fast-growing hardwoods, the holocellulose content for the Chinese tallow tree wood was somewhat higher (83.3%). The alpha-cellulose (48.3%) and Klason lignin (20.3%) contents were found to be similar to those for most native North American hardwoods. Results suggest that Chinese tallow tree wood utilization along with commercial wood species should not present any significant processing problems related to the extractives or cell-wall chemistry. Keywords: Cellulose, Chinese tallow tree, extractives, Klason lignin, utilization.

Thomas L. Eberhardt; Usda Forest Service; Xiaobo Li; Chung Y. Hse; Usda Forest Service

2005-01-01T23:59:59.000Z

106

Precision wood particle feedstocks  

DOE Patents (OSTI)

Wood particles having fibers aligned in a grain, wherein: the wood particles are characterized by a length dimension (L) aligned substantially parallel to the grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) normal to W and L; the L.times.H dimensions define two side surfaces characterized by substantially intact longitudinally arrayed fibers; the W.times.H dimensions define two cross-grain end surfaces characterized individually as aligned either normal to the grain or oblique to the grain; the L.times.W dimensions define two substantially parallel top and bottom surfaces; and, a majority of the W.times.H surfaces in the mixture of wood particles have end checking.

Dooley, James H; Lanning, David N

2013-07-30T23:59:59.000Z

107

The Pitfalls of Realist Analysis of Global Capitalism: A Critique of Ellen Meiksins Wood’s Empire of Capitalism: A Critique of Ellen Meiksins Wood's "Empire of Capital"  

E-Print Network (OSTI)

Boulder: Paradigm Press. Wood, Ellen Meiksins 2002, ‘Globalgroups. 13 Indeed, Wood 2003, p. 23. Wood 2003, p. 132.Ibid. Wood 2003, p. 129. Wood 2003, p. 133. Wood 2003, p.

Robinson, William I.

2007-01-01T23:59:59.000Z

108

Water-Activated, Shape Memory Twist Effect in Wood Slivers as an ...  

Science Conference Proceedings (OSTI)

This shape memory twist effect in wood could inspire new smart materials for a wide range of applications, including sensors, actuators, biomedical devices, and

109

Mitigation potential and cost in tropical forestry - relative role for agroforestry  

E-Print Network (OSTI)

Potential for Carbon Sequestration and Emission ReductionForestry Options on Carbon Sequestration in India'. WorkingGas Emissions and Carbon Sequestration in the Forest Sector

Makundi, Willy R.; Sathaye, Jayant A.

2004-01-01T23:59:59.000Z

110

"just like fingernail and flesh": Community forestry, biogas, and environmental governmentality in Nepal.  

E-Print Network (OSTI)

??Community forestry and household biogas digesters that reduce firewood dependence for cooking are two complimentary and relatively successful programs in Nepal. Both have their roots… (more)

Barnhart, Shaunna

2012-01-01T23:59:59.000Z

111

Urban Community Forestry in Washington, DC and Baltimore, MD: The Role of Nonprofit Organizations.  

E-Print Network (OSTI)

??Since the 1980s environmental service delivery funding at both the state and city government level has been in decline, limiting urban community forestry programs. This… (more)

Rodier, Meghan L.

2011-01-01T23:59:59.000Z

112

Burls and Other Unusual Woods  

NLE Websites -- All DOE Office Websites (Extended Search)

President Roland F. Eisenbeis, Supt. of Conservation BURLS AND OTHER UNUSUAL WOODS Wood worked by the hands of skilled craftsmen puts a wealth of quiet beauty into our daily...

113

The Asian Wood Pellet Markets  

E-Print Network (OSTI)

. 25 p. This study examines the three major wood pellet markets in Asia: China, Japan, and South Korea, South Korea is striving to increase its per- centage of renewable energy, which could benefit the wood pellets industry. We found that China, the largest energy consumer in Asia, has an established wood pellet

114

The Wood Duck  

NLE Websites -- All DOE Office Websites (Extended Search)

Wood Duck Wood Duck Nature Bulletin No. 502-A October 13, 1973 Forest Preserve District of Cook County George W. Dunne, President Roland F. Eisenbeis, Supt. of Conservation THE WOOD DUCK Of all the fowl that swim, the Wood Duck is a most unusual bird. They perch in trees like jaybirds, and nest in tree holes like woodpeckers. The hens do not quack like the females of most ducks, and the drakes are dressed in a riot of gaudy colors. Each summer we see dozens of them -- more than any other kind of wild duck -- rear their families of ducklings on and around the streams, ponds, lakes and sloughs of Cook County's forest preserves. Words can scarcely describe the brilliance of the drake's plumage. The head, crest and back glint with iridescent greens, purples and blues. The eyes are red, the throat white, and the bill orange-red. The breast is wine-colored flecked with white, the belly is white, and the sides are buff. The woodie is about midway in size between the mallard and the blue-winged teal. The drakes weigh about a pound and a half. The hen is smaller and plainer, with a gray-brown head and body, a white throat, and a conspicuous white ring around the eye. Her voice is a shrill, squealing "whoo-eek", while the male's is a mere squeak.

115

Development of polypropylene/wood flour ecocomposites. Evaluation of silane as coupling agent  

SciTech Connect

The effects of Pinus Sylvestris wood flour as filler in polypropylene matrix was evaluated. The mechanical properties and the morphology of different wood flour/polypropylene composites (WPC) were studied. The composites materials were prepared with several amounts of wood flour from 10 to 30% wt. Mechanical properties show that the wood flour incorporation increases the rigidity of the composites. Morphological analysis indicates that agglomerates are formed, with amounts exceeding 30% of wood flour. For the silane--treated composites, the dispersion of the filler into the polypropylene (PP) matrix improved. Shore D hardness of the composites is decreased with the addition of the coupling agent.

Bouza, R.; Barral, L.; Abad, M. J.; Montero, B. [Grupo de Polimeros, Dpto. de Fisica, E.U.P. Ferrol, Universidad de A Coruna, Avda. 19 de Febrero s/n, 15405 Ferrol (Spain)

2010-06-02T23:59:59.000Z

116

Inside the guts of wood-eating catfishes: can they digest wood?  

E-Print Network (OSTI)

the cellulolytic system of the wood-boring marine mollusk2008), how diVerent are the wood-eating catWshes from otherendosymbionts and digest wood, or are these wood- eating

German, Donovan P.

2009-01-01T23:59:59.000Z

117

Materials Characterization Paper In Support of the Proposed Rulemaking: Identification of Nonhazardous Secondary Materials That Are Solid Waste  

E-Print Network (OSTI)

Resinated wood products are derived from primary and secondary wood products manufacturing and are generally comprised of such items as board trim, sander dust, and panel trim. These secondary materials may be used on-site to manufacture composites or used as fuel. This paper focuses on resinated wood dust because of its importance as a fuel. Resinated wood dusts are primarily generated from the manufacturing of secondary wood products (Short 1993). More specifically, non-hazardous resinated wood dusts are generated from the sanding and sawing of engineered wood, plywood, and reconstituted wood products. 2. Annual Quantities of Resinated Wood Dusts Generated and Used (1) Sectors that generate resinated wood dusts: The following industry sectors, listed by NAICS code, generate resinated wood dust through the production of wood products:

Resinated Wood Products

2010-01-01T23:59:59.000Z

118

WOOD FLOORING 1. INTRODUCTION TO WARM AND WOOD FLOORING  

E-Print Network (OSTI)

This chapter describes the methodology used in EPA’s Waste Reduction Model (WARM) to estimate streamlined life-cycle greenhouse gas (GHG) emission factors for wood flooring beginning at the waste generation reference point. 1 The WARM GHG emission factors are used to compare the net emissions associated with wood flooring in the following three waste management alternatives: source reduction, combustion, and landfilling.

unknown authors

2012-01-01T23:59:59.000Z

119

Energy Basics: Wood and Pellet Heating  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

EERE: Energy Basics Wood and Pellet Heating Wood-burning and pellet fuel appliances use biomass or waste resources to heat homes or buildings. Types of Wood- and Pellet-Burning...

120

Energy Basics: Wood and Pellet Heating  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Heating & Cooling Systems Water Heating Wood and Pellet Heating Wood-burning and pellet fuel appliances use biomass or waste resources to heat homes or buildings. Types of Wood-...

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

CHEMISTRY AND STOICHIOMETRY OF WOOD LIQUEFACTION  

E-Print Network (OSTI)

V. , Anderson, Carry, Academic, New York. Pyrolysis of WoodT.J. Elder, E.J. Soltes, Wood and Fiber, 12(4), 1980, "Phenolic Constituents of a Wood Pyrolytic Oil." J.A. Knight,

Davis, H.G.

2012-01-01T23:59:59.000Z

122

Shell-armored wood cobbles as a potential criterion for detrital coal deposits  

Science Conference Proceedings (OSTI)

Shell-armored wood cobbles occur on detrital-peat beaches along the seaward edge of the Mississippi Delta. Shell material consists exclusively of Mulinia lateralis, a dwarf surf clam. Soft, heavy, waterlogged wood fragments are abraded and become armored by hard shells in response to wave activity on the beach. Although their preservation potential is suspect, fossilized shell-armored wood clasts would probably be recognized as a type of coal ball and might indicate an allochthonous origin for the host coal.

DiMarco, M.J.; Nummedal, D.

1986-01-01T23:59:59.000Z

123

Daniel Wood | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood Wood About Us Daniel Wood - Data Integration Specialist Daniel Wood Daniel Wood is the Data Visualization and Cartographic Specialist in the Office of Public Affairs at the Department of Energy. He develops creative and interactive ways of viewing the Energy Department's vast array of data. You can check out some of his work here. Prior to joining the Energy.gov team, Daniel worked at a large PR firm in Washington, D.C, doing web development and technical project management. Daniel is a graduate of Boston University but a true Philadelphian at heart. On his off days you are likely to find him exploring new neighborhoods on his bike or hanging out with the awesome kids over at Little Lights Urban Ministries. Most Recent The History of the Light Bulb November 22

124

Weathering and Protection of Wood  

E-Print Network (OSTI)

Introduction When wood is exposed outdoors, above ground, a complex combination of chemical, mechanical, and light energy factors contribute to what is described as weathering (38). Weathering is not to be confused with decay, which results from decay organisms (fungi) acting in the presence of excess moisture and air for an extended period of time (34). Under conditions suitable for the development of decay, wood can deteriorate rapidly and the result is far different than that observed for natural outdoor weathering, Outdoor Weathering Process In outdoor weathering of smooth wood, original surfaces become rough as grain raises and the wood checks, and the checks grow into large cracks; grain may loosen, boards cup and warp and pull away from fasteners (Figs. 1 and 2), The roughened surface changes color, gathers dirt and mildew, and may become unsightly; the wood loses its surface coherence and becomes friable, splinters, and frag ments come off. All these e

William C. Feist

1983-01-01T23:59:59.000Z

125

Carbon Market Opportunities for the Forestry Sector of Africa | Open Energy  

Open Energy Info (EERE)

Carbon Market Opportunities for the Forestry Sector of Africa Carbon Market Opportunities for the Forestry Sector of Africa Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Carbon Market Opportunities for the Forestry Sector of Africa Agency/Company /Organization: Food and Agriculture Organization of the United Nations, Winrock International Sector: Land Focus Area: Renewable Energy, Forestry Topics: Implementation, Policies/deployment programs Resource Type: Presentation Website: www.winrock.org/ecosystems/files/Winrock_FAO_Carbon_opportunities_in_A UN Region: "Sub-Saharan Africa" is not in the list of possible values (Eastern Africa, Middle Africa, Northern Africa, Southern Africa, Western Africa, Caribbean, Central America, South America, Northern America, Central Asia, Eastern Asia, Southern Asia, South-Eastern Asia, Western Asia, Eastern Europe, Northern Europe, Southern Europe, Western Europe, Australia and New Zealand, Melanesia, Micronesia, Polynesia, Latin America and the Caribbean) for this property.

126

Wood and energy in connecticut. Staff report  

SciTech Connect

Telephone surveys of Connecticut households conducted in 1979 indicate a transition to wood heating in response to a series of conventional energy price increases and uncertainty in conventional energy supplies. Connecticut households consumed 668,000 cords of wood in the winter of 1978-79. The airtight wood stove has become the most commonly used wood-burning apparatus. Survey data of residential wood cutting, purchasing, and burning were analyzed by household tenure, wood-burning apparatus, and county. Residential use of wood for energy constitutes a new demand on the forest resource, increases local income and employment, displaces fuel oil and electricity, but may compromise household safety.

Bailey, M.R.; Wheeling, P.R.; Lenz, M.I.

1983-03-01T23:59:59.000Z

127

Managing Transmission Line Wood Structures  

Science Conference Proceedings (OSTI)

The objective of this project is to reduce capital cost by extending life expectancy of overhead transmission wood structures through inspection and assessment procedures and through aging mitigation techniques and tools.

2005-11-29T23:59:59.000Z

128

Treated Wood Planted Post Study  

Science Conference Proceedings (OSTI)

This Technical Update describes the interim results of a planted post study currently under way at the Austin Cary Memorial Forest (ACMF), operated by The University of Florida, in Gainesville. The purpose of this research is to examine the effectiveness of commercially available prevention methods to reduce preservative migration from treated wood poles, compare the migration of constituents of various wood treatments, and assess the environmental impacts and performance of untreated chestnut.

2009-11-12T23:59:59.000Z

129

Carbon mitigation potential and costs of forestry options in Brazil, China, India, Indonesia, Mexico, the Phillippines and Tanzania  

E-Print Network (OSTI)

potential for carbon sequestration and emission reductionForestry Options on Carbon Sequestration in India, Workinggas emissions and carbon sequestration in the forest sector

Sathaye, J.

2008-01-01T23:59:59.000Z

130

An Overview of the Louisiana Secondary Wood Products Industry  

E-Print Network (OSTI)

the State of Louisiana. In addition, because the origin of material purchased from in-state suppliers cannot of the development of buying or manufacturing cooperatives that could create purchasing and sales/marketing leverage Secondary Wood Product Manufacturers Number of Employees by Establishment (Percent of respondent companies

131

Table F24: Wood and Biomass Waste Consumption Estimates, 2011  

U.S. Energy Information Administration (EIA)

Table F24: Wood and Biomass Waste Consumption Estimates, 2011 State Wood Wood and Biomass Waste a Residential Commercial Industrial Electric Power ...

132

Chromoblastomycosis associated with in a carpenter handling exotic woods  

E-Print Network (OSTI)

in a carpenter handling exotic woods Nuno Menezes 1 , Pauloas saprophytes in the soil, wood and vegetation [ 3 ]. Theyare normally made of tropical wood [ 9 ]. The inoculation

2008-01-01T23:59:59.000Z

133

Riparian forest disturbances by a mountain flood -- the influence of floated wood  

E-Print Network (OSTI)

Large floods can have major impacts on riparian forests. Here we examine the variability and spatial distribution of riparian forest responses along eight third- to fifth-order streams following a large flood ( 100 year recurrence interval) in the Cascade Mountain Range of Oregon. We categorized disturbance intensity (physical force) exerted on riparian trees during floods into three classes: (i) purely fluvial (high water flow only); (ii) ¯uvial supplemented by dispersed pieces of floating wood (uncongested wood transport); (iii) fluvial with movement of batches of wood (congested wood transport). These types of material transport and associated classes of disturbance intensity resulted in a gradient of biotic responses of disturbance severity ranging from standing riparian trees inundated by high water, to trees toppled but still partially rooted, to complete removal of trees. High within-stream and among stream responses were inflenced by pre-flood stream and riparian conditions as well as flood dynamics, especially the availability of individual pieces or congested batches of wood. Fluvial disturbance alone toppled fewer riparian trees than in reaches where floodwaters transported substantial amounts of wood. Debris flows delivered additional wood and sediment to parts of reaches of four of these study streams; riparian trees were removed and toppled for up to 1 5 km downstream of the debris flow tributary channel. Congested wood transport resulted in higher frequency of toppled trees and greater deposition of new wood levees along channel margins. The condition of the landscape at the time of a major ¯ood strongly influenced

Sherri L. Johnson; Frederick J. Swanson; Gordon E. Grant; Steven M. Wondzell

2000-01-01T23:59:59.000Z

134

Utah Division of Forestry, Fire and State Lands | Open Energy Information  

Open Energy Info (EERE)

Forestry, Fire and State Lands Forestry, Fire and State Lands Jump to: navigation, search Logo: Utah Division of Forestry, Fire and State Lands Name Utah Division of Forestry, Fire and State Lands Address 1594 W. North Temple, Ste 3520 Place Salt Lake City, Utah Zip 84114-5703 Phone number 801.538.5555 Website http://forestry.utah.gov/ffsl. Coordinates 40.7713859°, -111.9367973° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.7713859,"lon":-111.9367973,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

135

Forestry and Poverty Data in Vietnam: Status, Gaps, and Potential Uses |  

Open Energy Info (EERE)

Forestry and Poverty Data in Vietnam: Status, Gaps, and Potential Uses Forestry and Poverty Data in Vietnam: Status, Gaps, and Potential Uses Jump to: navigation, search Tool Summary Name: Forestry and Poverty Data in Vietnam: Status, Gaps, and Potential Uses Agency/Company /Organization: Regional Community Forestry Training Center for Asia and the Pacific Sector: Land Focus Area: Forestry Topics: Co-benefits assessment, Background analysis Resource Type: Dataset, Publications Website: recoftc.org/site/fileadmin/docs/publications/The_Grey_Zone/2009/Forest Country: Vietnam UN Region: South-Eastern Asia Coordinates: 14.058324°, 108.277199° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":14.058324,"lon":108.277199,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

136

Wood and Pellet Heating | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood and Pellet Heating Wood and Pellet Heating Wood and Pellet Heating November 25, 2013 - 2:24pm Addthis A wood stove on a stone hearth. | Photo courtesy of ©iStockphoto/King_Louie A wood stove on a stone hearth. | Photo courtesy of ©iStockphoto/King_Louie What does this mean for me? Wood or pellets may be an economical and environmentally sound heating fuel choice. If you live in an area where you can cut your own wood for heating, your fuel will be local and inexpensive. Today you can choose from a new generation of wood- and pellet-burning appliances that are cleaner burning, more efficient, and powerful enough to heat many average-sized, modern homes. Pellet fuel appliances burn small pellets that measure 3/8 to 1 inch in length. Choosing and Installing Wood- and Pellet-Burning Appliances

137

Wood Energy in Alaska– Case Study Evaluations of Selected Facilities  

E-Print Network (OSTI)

multiple use management of the Nation’s forest resources for sustained yields of wood, water, forage, wildlife, and recreation. Through forestry research, cooperation with the States and private forest owners, and management of the National Forests and National Grasslands, it strives—as directed by Congress—to provide increasingly greater service to a growing Nation. The U.S. Department of Agriculture (USDA) prohibits discrimination in all its programs and activities on the basis of race, color, national origin, age, disability, and where applicable, sex, marital status, familial status, parental status, religion, sexual orientation, genetic information, political beliefs, reprisal, or because all or part of an individual’s income is derived from any public assistance program. (Not all prohibited bases apply to all programs.) Persons with disabilities who require alternative means for communication of program information (Braille, large print, audiotape, etc.) should contact USDA’s TARGET Center at (202) 720-2600 (voice and TDD). To file a complaint of discrimination, write

United States; Forest Service

2009-01-01T23:59:59.000Z

138

Table 3.6 Selected Wood and Wood-Related Products in Fuel Consumption, 2010;  

U.S. Energy Information Administration (EIA) Indexed Site

Table 3.6 Selected Wood and Wood-Related Products in Fuel Consumption, 2010; Table 3.6 Selected Wood and Wood-Related Products in Fuel Consumption, 2010; Level: National and Regional Data; Row: Selected NAICS Codes; Column: Energy Sources; Unit: Trillion Btu. Wood Residues and Wood-Related Pulping Liquor Wood Byproducts and NAICS or Biomass Agricultural Harvested Directly from Mill Paper-Related Code(a) Subsector and Industry Black Liquor Total(b) Waste(c) from Trees(d) Processing(e) Refuse(f) Total United States 311 Food 0 44 43 * * 1 311221 Wet Corn Milling 0 1 1 0 0 0 312 Beverage and Tobacco Products 0 1 0 0 1 0 321 Wood Products 0 218 * 13 199 6 321113 Sawmills 0 100 * 5 94 1 3212 Veneer, Plywood, and Engineered Woods 0 95 * 6 87 2 321219 Reconstituted Wood Products 0 52 0 6 46 1 3219 Other Wood Products

139

Hawaii Department of Land and Natural Resources Division of Forestry and  

Open Energy Info (EERE)

Forestry and Forestry and Wildlife Jump to: navigation, search Name Hawaii Department of Land and Natural Resources Division of Forestry and Wildlife Address Kalanimoku Building 1151 Punchbowl St., Room 325 Place Honolulu, Hawaii Zip 96813 Website http://hawaii.gov/dlnr/dofaw Coordinates 21.305788°, -157.855682° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":21.305788,"lon":-157.855682,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

140

Special Issue On Estimation Of Baselines And Leakage In CarbonMitigation Forestry Projects  

SciTech Connect

There is a growing acceptance that the environmentalbenefits of forests extend beyond traditional ecological benefits andinclude the mitigation of climate change. Interest in forestry mitigationactivities has led to the inclusion of forestry practices at the projectlevel in international agreements. Climate change activities place newdemands on participating institutions to set baselines, establishadditionality, determine leakage, ensure permanence, and monitor andverify a project's greenhouse gas benefits. These issues are common toboth forestry and other types of mitigation projects. They demandempirical evidence to establish conditions under which such projects canprovide sustained long term global benefits. This Special Issue reportson papers that experiment with a range of approaches based on empiricalevidence for the setting of baselines and estimation of leakage inprojects in developing Asia and Latin America.

Sathaye, Jayant A.; Andrasko, Kenneth

2006-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Housing 2020: The future of wood in U.S. dwellings  

Science Conference Proceedings (OSTI)

This paper presented at the International Panel and Engineered-Wood Technology Exposition examines the effect that reduced material resources, energy conservation, manufactured dwellings, and construction techniques have had on the use of wood in the housing industry. The topics of the paper include the impact of the energy crisis, financing and affordability crisis, lumber crisis, and a forecast of what the house of the year 2020 will look like, how it will be constructed and of what material will it be constructed.

Wendt, R.L. [Oak Ridge National Lab., TN (United States). Energy Div.

1994-12-31T23:59:59.000Z

142

Weathering of roofing materials - an overview  

NLE Websites -- All DOE Office Websites (Extended Search)

and hasten diffusion of material components. Effects of moisture include decay of wood, acceleration of corrosion of metals, staining of clay, and freeze-thaw damage....

143

Wood-Composites Industry Benefits from ALS Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Wood-Composites Industry Benefits from ALS Research Wood-Composites Industry Benefits from ALS Research Print Thursday, 25 October 2012 10:44 paris-wood composites Wood scientist...

144

Categorical Exclusion for Wood Pole  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood Pole Wood Pole Replacement at two structures (11/6 & 11/9) located along the Oracle-Tucson 115-kV Transmission Line, in Oro Valley, Pima County, Arizona. RECORD OF CATEGORICAL EXCLUSION DETERMINATION A. Proposed Action: Western plans to replace deteriorated wood poles, cross arms and X-braces at two existing H-frame structures (11/6 & 1119) located along the Oracle Tucson 115-kV Transmission Line in Pima, Arizona (Figure 1). Built in 1943, its aging components are beyond repair and require replacement. These poles performed poorly during structural tests, and we consider them unstable. This replacement project will ensure the safety of Western's workers and the public as well as reliability of the bulk electric system. Western will accomplish the work by clearing vegetation and blading a level pad at

145

Marin County- Wood Stove Replacement Rebate Program  

Energy.gov (U.S. Department of Energy (DOE))

The County of Marin has created a rebate program to encourage homeowners to remove or replace non-EPA certified wood-burning heaters (wood stoves and fireplace inserts) with cleaner burning stoves...

146

Structure-Infesting Wood-Boring Beetles  

E-Print Network (OSTI)

Several kinds of beetles damage stored wood, structural timbers and other wood products. This publication explains how to detect, identify, prevent and control powderpost beetle, old house borer and others.

Jackman, John A.

2006-03-28T23:59:59.000Z

147

URBAN WOOD/COAL CO-FIRING IN THE NIOSH BOILERPLANT  

DOE Green Energy (OSTI)

During the third quarter, the experimental portion of the project was carried out. Three one-day tests using wood/coal blends of 33% wood by volume (both construction wood and demolition wood) were conducted at the NIOSH Boiler Plant (NBP). Blends using hammer-milled wood were operationally successful and can form the basis of Phase II. Emissions of SO{sub 2} and NOx decreased and that of CO increased when compared with combusting coal alone. Mercury emissions were measured and the mathematical modeling of mercury speciation reactions continued, yielding many interesting results. Material and energy balances for the test periods at the NBP, as well as at the Bellefield Boiler Plant, were prepared. Steps were taken to remove severe constraints from the Pennsylvania Switchgrass Energy and Conservation Project and to organize the supplying of landfill gas to the Bruceton federal complex. Two presentations were made to meetings of the Electric Power Research Institute and the National Energy Technology Laboratory.

James T. Cobb, Jr.; Gene E. Geiger; William W. Elder III; Thomas Stickle; Jun Wang; Hongming Li; William P. Barry

2002-06-13T23:59:59.000Z

148

Field Guide: Visual Inspection of Wood Structures  

Science Conference Proceedings (OSTI)

The Field Guide: Visual Inspection of Wood Structures is a catalog of photographs illustrating various conditions and factors that commonly affect transmission line wood structures, along with their likely causes, a Maintenance Priority Rating, and suggested actions to be taken by utility personnel. Poles, cross-arms, cross-arm braces, X-braces, brackets, anchor rods, guy wires, and direct imbedded foundations are covered. Other sections include types of wood structures, the anatomy of wood ...

2013-10-28T23:59:59.000Z

149

Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

Materials Materials and methods are available as supplementary materials on Science Online. 16. W. Benz, A. G. W. Cameron, H. J. Melosh, Icarus 81, 113 (1989). 17. S. L. Thompson, H. S. Lauson, Technical Rep. SC-RR-710714, Sandia Nat. Labs (1972). 18. H. J. Melosh, Meteorit. Planet. Sci. 42, 2079 (2007). 19. S. Ida, R. M. Canup, G. R. Stewart, Nature 389, 353 (1997). 20. E. Kokubo, J. Makino, S. Ida, Icarus 148, 419 (2000). 21. M. M. M. Meier, A. Reufer, W. Benz, R. Wieler, Annual Meeting of the Meteoritical Society LXXIV, abstr. 5039 (2011). 22. C. B. Agnor, R. M. Canup, H. F. Levison, Icarus 142, 219 (1999). 23. D. P. O'Brien, A. Morbidelli, H. F. Levison, Icarus 184, 39 (2006). 24. R. M. Canup, Science 307, 546 (2005). 25. J. J. Salmon, R. M. Canup, Lunar Planet. Sci. XLIII, 2540 (2012). Acknowledgments: SPH simulation data are contained in tables S2 to S5 of the supplementary materials. Financial support

150

Table 3.6 Selected Wood and Wood-Related Products in Fuel Consumption, 2002  

U.S. Energy Information Administration (EIA) Indexed Site

6 Selected Wood and Wood-Related Products in Fuel Consumption, 2002;" 6 Selected Wood and Wood-Related Products in Fuel Consumption, 2002;" " Level: National and Regional Data; " " Row: Selected NAICS Codes; Column: Energy Sources;" " Unit: Trillion Btu." ,,"S e l e c t e d","W o o d","a n d","W o o d -","R e l a t e d","P r o d u c t s" ,,,,,"B i o m a s s" ,,,,,,"Wood Residues" ,,,,,,"and","Wood-Related" " "," ","Pulping Liquor"," "," ","Wood","Byproducts","and","RSE",," " "NAICS"," ","or","Biomass","Agricultural","Harvested Directly","from Mill","Paper-Related","Row"

151

Table N5.2. Selected Wood and Wood-Related Products in Fuel Consumption, 1998  

U.S. Energy Information Administration (EIA) Indexed Site

2. Selected Wood and Wood-Related Products in Fuel Consumption, 1998;" 2. Selected Wood and Wood-Related Products in Fuel Consumption, 1998;" " Level: National and Regional Data; " " Row: Selected NAICS Codes; Column: Energy Sources;" " Unit: Trillion Btu." ,,"S e l e c t e d","W o o d","a n d","W o o d -","R e l a t e d","P r o d u c t s" ,,,,,"B i o m a s s" ,,,,,,"Wood Residues" ,,,,,,"and","Wood-Related" " "," ","Pulping Liquor"," "," ","Wood","Byproducts","and","RSE",," " "NAICS"," ","or","Biomass","Agricultural","Harvested Directly","from Mill","Paper-Related","Row"

152

Material  

DOE Green Energy (OSTI)

Li(Ni{sub 0.4}Co{sub 0.15}Al{sub 0.05}Mn{sub 0.4})O{sub 2} was investigated to understand the effect of replacement of the cobalt by aluminum on the structural and electrochemical properties. In situ X-ray absorption spectroscopy (XAS) was performed, utilizing a novel in situ electrochemical cell, specifically designed for long-term X-ray experiments. The cell was cycled at a moderate rate through a typical Li-ion battery operating voltage range. (1.0-4.7 V) XAS measurements were performed at different states of charge (SOC) during cycling, at the Ni, Co, and the Mn edges, revealing details about the response of the cathode to Li insertion and extraction processes. The extended X-ray absorption fine structure (EXAFS) region of the spectra revealed the changes of bond distance and coordination number of Ni, Co, and Mn absorbers as a function of the SOC of the material. The oxidation states of the transition metals in the system are Ni{sup 2+}, Co{sup 3+}, and Mn{sup 4+} in the as-made material (fully discharged), while during charging the Ni{sup 2+} is oxidized to Ni{sup 4+} through an intermediate stage of Ni{sup 3+}, Co{sup 3+} is oxidized toward Co{sup 4+}, and Mn was found to be electrochemically inactive and remained as Mn{sup 4+}. The EXAFS results during cycling show that the Ni-O changes the most, followed by Co-O, and Mn-O varies the least. These measurements on this cathode material confirmed that the material retains its symmetry and good structural short-range order leading to the superior cycling reported earlier.

Rumble, C.; Conry, T.E.; Doeff, Marca; Cairns, Elton J.; Penner-Hahn, James E.; Deb, Aniruddha

2010-06-14T23:59:59.000Z

153

Autonomous Underwater Gliders Wood, Stephen  

E-Print Network (OSTI)

26 Autonomous Underwater Gliders Wood, Stephen Florida Institute of Technology United States underwater vehicles to perform ocean surveys. With these vehicles it is now possible for the scientist substances in the ocean such as chemicals from an underwater vent or toxic algae such as red tide

Wood, Stephen L.

154

Department of Renewable Resources Faculty of Agriculture, Forestry, and Home Economics  

E-Print Network (OSTI)

Department of Renewable Resources Faculty of Agriculture, Forestry, and Home Economics Dept. Renewable Resources · University of Alberta · Edmonton · Canada · T6G 2E3 Telephone: (780) 492-8511 · Email ­ Tree Ecophysiology Applications are invited for a MSc student position in the Department of Renewable

Hacke, Uwe

155

The Colorado State Forest Service is the lead state agency for forestry and wildfire expertise.  

E-Print Network (OSTI)

The Colorado State Forest Service is the lead state agency for forestry and wildfire expertise. Colorado State Forest Service http://csfs.colostate.edu/ CSFS is proud to be a part of the Warner College of Natural Resources at Colorado State University, headquartered in Fort Collins. We have approximately 130

156

Davide Pettenella and Enrico Vidale Dept. Landuse and Agro-forestry Systems  

E-Print Network (OSTI)

increase the resilience of the system. Case-study findings Two components of the most advanced form18-02-2010 1 Davide Pettenella and Enrico Vidale Dept. Landuse and Agro-forestry Systems University in public mountain areas (max 1Kg of Boletes in total 2Kg of WEF, time limitation to the daylight ) Pickers

Pettenella, Davide

157

James F. Wood | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

James F. Wood James F. Wood About Us James F. Wood - Deputy Assistant Secretary for Clean Coal Photo of James Wood Photo of James Wood James F. Wood is currently Deputy Assistant Secretary for Clean Coal in the Office of Fossil Energy (FE). In this position, he is responsible for the management and direction of the Office's clean coal research and development programs. Chief among these is the Carbon Sequestration program, the Clean Coal Power Initiative, and FE's $3.4 billion portfolio of Recovery Act projects. Wood has over 30 years of experience in the power industry. Most recently, he was president and CEO of Babcock Power Inc. (BPI), one of the major US-based designer/manufacturers of environmental, pressure part, heat exchanger, combustion equipment and after-market

158

Qualifying Wood Stove Deduction | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Qualifying Wood Stove Deduction Qualifying Wood Stove Deduction Qualifying Wood Stove Deduction < Back Eligibility Residential Savings Category Bioenergy Maximum Rebate 500 Program Info Start Date 1/1/1994 State Arizona Program Type Personal Deduction Rebate Amount Total cost, exclusive of taxes, interest and other finance charges Provider Arizona Department of Revenue This incentive allows Arizona taxpayers to deduct the cost of converting an existing wood fireplace to a qualifying wood stove. The cost to purchase and install all necessary equipment is tax deductible, up to a maximum $500 deduction. Qualifying wood stoves must meet the standards of performance for new wood heaters manufactured after July 1990, or sold after July 1992 pursuant to [http://www.epa.gov/oecaerth/resources/policies/monitoring/caa/woodstover...

159

Vertical feed stick wood fuel burning furnace system  

DOE Patents (OSTI)

A new and improved stove or furnace for efficient combustion of wood fuel including a vertical feed combustion chamber for receiving and supporting wood fuel in a vertical attitude or stack, a major upper portion of the combustion chamber column comprising a water jacket for coupling to a source of water or heat transfer fluid and for convection circulation of the fluid for confining the locus of wood fuel combustion to the bottom of the vertical gravity feed combustion chamber. A flue gas propagation delay channel extending from the laterally directed draft outlet affords delayed travel time in a high temperature environment to assure substantially complete combustion of the gaseous products of wood burning with forced air as an actively induced draft draws the fuel gas and air mixture laterally through the combustion and high temperature zone. Active sources of forced air and induced draft are included, multiple use and circuit couplings for the recovered heat, and construction features in the refractory material substructure and metal component superstructure.

Hill, Richard C. (Orono, ME)

1984-01-01T23:59:59.000Z

160

Vertical feed stick wood fuel burning furnace system  

DOE Patents (OSTI)

A stove or furnace for efficient combustion of wood fuel includes a vertical feed combustion chamber (15) for receiving and supporting wood fuel in a vertical attitude or stack. A major upper portion of the combustion chamber column comprises a water jacket (14) for coupling to a source of water or heat transfer fluid for convection circulation of the fluid. The locus (31) of wood fuel combustion is thereby confined to the refractory base of the combustion chamber. A flue gas propagation delay channel (34) extending laterally from the base of the chamber affords delayed travel time in a high temperature refractory environment sufficient to assure substantially complete combustion of the gaseous products of wood burning with forced air prior to extraction of heat in heat exchanger (16). Induced draft draws the fuel gas and air mixture laterally through the combustion chamber and refractory high temperature zone to the heat exchanger and flue. Also included are active sources of forced air and induced draft, multiple circuit couplings for the recovered heat, and construction features in the refractory material substructure and metal component superstructure.

Hill, Richard C. (Orono, ME)

1982-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Managing Transmission Line Wood Structures  

Science Conference Proceedings (OSTI)

Transmission and distribution infrastructures throughout the world are aging. As such, inspection, assessment, and maintenance of existing facilities have become increasingly important topics. This valuable reference provides an in-depth look at all facets of an inspection, assessment, and maintenance program for transmission line wood structures to help utilities develop and refine individual maintenance programs. The report is part of a broader multi-year effort by EPRI to develop a comprehensive handb...

2006-09-28T23:59:59.000Z

162

Distribution Library--Wood Poles  

Science Conference Proceedings (OSTI)

EPRI has sponsored research and published information on a wide variety of topics related to wood poles for overhead lines. Many of these resources, particularly older publications, are difficult for EPRI members to find and use. To help ensure retention of this valuable knowledge base, EPRI sponsored the project reported herein to capture this information and make it accessible in an easy-to-use electronic media (E-Media) repository.

2005-12-22T23:59:59.000Z

163

Wood Poles Population with Testing  

Science Conference Proceedings (OSTI)

EPRI's asset management research focuses on developing a rational basis for selecting repair or replacement options for specific classes of equipment by balancing the risks of equipment failure against the costs of continued maintenance or capital replacement. This Model User Guide is a companion to Guidelines for Intelligent Asset Replacement: Volume 4Wood Poles (Expanded Edition), EPRI, Palo Alto, CA: 2006. 1012500, the fourth report on guidelines for asset replacement, which discusses methods for maki...

2006-12-18T23:59:59.000Z

164

The morphological development of a wood burl shader  

E-Print Network (OSTI)

In the field of computer graphics, shaders provide an interface between lights and surfaces, giving the appearance of metal, plastic, wood, etc. As the field progresses, more and more shaders are required to simulate a wider and wider variety of materials. We present a new shader for the simulation of wood burl, a complex material used in furniture, art, car interiors, and a host of other luxury items. This shader was developed through a morphological approach - a study of the original material, its structure, and growth. Consequently, research began with a thorough look at wood burl, polished and unpolished, in an assortment of different species. We discovered the appearance can be broken into three sub-appearances - knots, curl, and a subtle undergrain. These three sub-appearances interact to create the characteristic swirls and whorls of burl. For the subtle undergrain, we used a common oak shader, added noise, and faded it into the background. We then developed a system of randomly placing points through the material to act as knots. Since the knots grow and distort the surrounding grain, we used distance-scaled forces to push the surface coordinates around and between all the knots. When the oak shader is applied, it appears to swirl and curl around the knots, much like a stream between rocks. This created the first level of curl or swirly grained wood, but one level alone appeared flat. To solve this, we procedurally blended levels of curl to give a look of increased depth. Finally, we added reflection, gloss, and other surface properties to give a look of warmth and polish. All of these properties are controlled by a set of parameters in the shader's interface. By adjusting these parameters, the user can emulate a variety of different burl types.

Moyer, Robert Simms

2003-12-01T23:59:59.000Z

165

Best Practices for Biomass Handling in Wood Yard Operations  

Science Conference Proceedings (OSTI)

Utilities are beginning to add wood and other biomass fuels to fire their generating units to enable them to produce carbon-neutral electricity and participate in state or national renewable energy programs. However, because the material handling aspects of biomass differ from those of coal, firing at a significant scale requires new equipment to receive, store, and deliver the biomass to the flame front. This equipment is analogous in function to existing machinery but is quite different in detail, desi...

2011-08-29T23:59:59.000Z

166

GLOBAL CLIMATE CHANGE: SOME IMPLICATIONS, OPPORTUNITIES. AND CHALLENGES FOR U.S. FORESTRY  

NLE Websites -- All DOE Office Websites (Extended Search)

GLOBAL CLIMATE CHANGE: SOME IMPLICATIONS, OPPORTUNITIES. GLOBAL CLIMATE CHANGE: SOME IMPLICATIONS, OPPORTUNITIES. AND CHALLENGES FOR U.S. FORESTRY G. Marland' Ahsiract.--It is widcly agrccd that thc concentration of greenhouse gases in the earth's atmosphcrc is increasing, that this increase is a consequence of man's activities, and that there is signilicant risk that this will lead to changes in the earth's climate. T h c qucstion is now k i n g discusscd what, if anything, we should be doing to minimize and/or adapt to changes in climate. Virtually evcry statcmcnt on this matter; from the G.S. Oflice of Tcchnology Assessment. to the National Acadcmy of Science, to the Nairobi Declaration on Climatic Change. includes some recommendation for planting and protecting forests. In fact, forestry is intimately involved in the climate change

167

The Effect of Transaction Costs on Greenhouse Gas Emission Mitigation for Agriculture and Forestry  

E-Print Network (OSTI)

Climate change and its mitigation is rapidly becoming an item of social concern. Climate change mitigation involves reduction of atmospheric greenhouse gas concentrations through emissions reduction and or sequestration enhancement (collectively called offsets). Many have asked how agriculture and forestry can participate in mitigation efforts. Given that over 80 percent of greenhouse gas emissions arise from the energy sector, the role of agriculture and forestry depends critically on the costs of the offsets they can achieve in comparison with offset costs elsewhere in the economy. A number of researchers have examined the relative offset costs but have generally looked only at producer level costs. However there are also costs incurred when implementing, selling and conveying offset credits to a buyer. Also when commodities are involved like bioenergy feedstocks, the costs of readying these for use in implementing an offset strategy need to be reflected. This generally involves the broadly defined category of transaction costs. This dissertation examines the possible effects of transactions costs and storage costs for bioenergy commodities and how they affect the agriculture and forestry portfolio of mitigation strategies across a range of carbon dioxide equivalent prices. The model is used to simulate the effects with and without transactions and storage costs. Using an agriculture and forestry sector model called FASOMGHG, the dissertation finds that consideration of transactions and storage costs reduces the agricultural contribution total mitigation and changes the desirable portfolio of alternatives. In terms of the portfolio, transactions costs inclusion diminishes the desirability of soil sequestration and forest management while increasing the bioenergy and afforestation role. Storage costs diminish the bioenergy role and favor forest and sequestration items. The results of this study illustrate that transactions and storage costs are important considerations in policy and market design when addressing the reduction of greenhouse gas concentrations in climate change related decision making.

Kim, Seong Woo

2011-05-01T23:59:59.000Z

168

EIA Energy Kids - Wood - Energy Information Administration  

U.S. Energy Information Administration (EIA)

1860: Wood was the primary fuel for heating and cooking in homes and businesses, and was used for steam in industries, trains, and boats.

169

The Bending of Wood With Steam.  

E-Print Network (OSTI)

??Based on experimentation with the steam bending of wood to curved shapes, this thesis describes my involvement with three basic aspects of the process. First… (more)

Cottey Jr., James H.

2008-01-01T23:59:59.000Z

170

Successful biomass (wood pellets ) implementation in  

E-Print Network (OSTI)

Successful biomass (wood pellets ) implementation in Estonia Biomass Utilisation of Local in Estonia in 1995 - 2002 Regional Energy Centres in Estonia http://www.managenergy.net/conference/biomass

171

Life Cycle Assessment of Wood Pellet.  

E-Print Network (OSTI)

??The primary purpose of this project is to assess the environmental impacts associated with the wood pellet production. The study has extended to the entire… (more)

Chen, Siyu

2009-01-01T23:59:59.000Z

172

Methanol production from eucalyptus wood chips  

DOE Green Energy (OSTI)

The technical feasibility of producing methanol from wood is demonstrated and sufficient cost data is provided to allow an assessment of the economic viability.

Fishkind, H.H.

1982-06-01T23:59:59.000Z

173

Wood, Wisconsin: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Wood, Wisconsin: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 43.568752, -90.330887 Loading map... "minzoom":false,"mappingservice":"googlem...

174

Emerging Technologies in Wood Energy Wood can already be used to produce heat and  

E-Print Network (OSTI)

for extension of wood pellet production is lack of appropriate technology in Slovakia. Several typesOverview 1 Development of Wood Chips and Pellets market in Slovakia Jozef Viglasky, SK systems. · Co-combustion of wood residues in existing coal fired power systems. #12;Overview 3

175

Mathematical simulation of temperature profiles within microwave heated wood made for wood-based nanocomposites  

Science Conference Proceedings (OSTI)

High intensive microwave pretreatment is a new method to modify wood for the fabrication of wood-based nanocomposites. Based on the physical law on heat transfer, a mathematical model to describe the temperature profiles within wood heated by high intensive ...

Xianjun Li, Yongfeng Luo, Hongbin Chen, Xia He, Jianxiong Lv, Yiqiang Wu

2013-01-01T23:59:59.000Z

176

Textile Drying Via Wood Gasification  

E-Print Network (OSTI)

This project was carried out to investigate the possibility of using wood gas as a direct replacement for natural gas in textile drying. The Georgia Tech updraft gasifier was used for the experimental program. During preliminary tests, the 1 million Btu/hr pilot plant produced clean burning gas which appeared viable for drying textiles. The gasifier was coupled to a modified textile drying oven and a series of tests were carried out to assess product degradation of white, colored, and chemically treated fabrics.

McGowan, T. F.; Jape, A. D.

1983-01-01T23:59:59.000Z

177

Treatment of Wood Preserving Wastewater  

E-Print Network (OSTI)

The wastewater produced by the wood preserving industry presents a difficult problem to treat economically. A review of the literature indicates the size of the industry has limited the pursuit of an orderly and economic solution. Atmospheric evaporation was one possible means of treatment which had not been studied to any great degree. Two bench scale evaporation units were employed to determine the fundamental relationships affecting wastewater quality during such treatment. In batch evaporation tests, it was repeatedly demonstrated that a constant rate of total organic carbon and chemical oxygen demand removal occurred as the wastewater was evaporated. A procedure for designing atmospheric evaporation ponds was developed and applied to a hypothetical wood preserving plant. From this example design estimates of equivalent hydrocarbon concentrations in the air downwind of the pond are made. Various other design considerations such as the input data, modifications to the design procedure, solids accumulation, and miscellaneous design aspects are discussed. A treatment scheme incorporating atmospheric evaporation ponds after chemical coagulation and settling is proposed.

Reynolds, T. D.; Shack, P. A.

1976-10-01T23:59:59.000Z

178

Management Practices for Used Treated Wood  

Science Conference Proceedings (OSTI)

Pentachlorophenol, creosote, and other chemicals are used to preserve poles, crossarms, and railroad ties for the electric, telecommunications, and railroad industries. Each year, millions of pieces of treated wood are retired. This report provides information on current and potential options for management of used treated wood.

1995-08-02T23:59:59.000Z

179

Modeling and Rendering Physically-Based Wood Combustion  

Science Conference Proceedings (OSTI)

This paper describes extensions to existing methods for rendering of the effects of combustion on a wood object, adding considerations for wood grain and moisture content.

Riensche, Roderick M.; Lewis, Robert R.

2009-08-01T23:59:59.000Z

180

Compound and Elemental Analysis At Little Valley Area (Wood,...  

Open Energy Info (EERE)

Area (Wood, 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Compound and Elemental Analysis At Little Valley Area (Wood, 2002) Exploration...

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Wood3 Resources | Open Energy Information  

Open Energy Info (EERE)

Wood3 Resources Wood3 Resources Jump to: navigation, search Name Wood3 Resources Place Houston, Texas Zip 77056-2409 Product Wood3 Resources is an energy project development firm run by former Federal Energy Regulatory Commission Chairman Pat Wood. Coordinates 29.76045°, -95.369784° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":29.76045,"lon":-95.369784,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

182

Alaska Wood Biomass Energy Project Final Report  

SciTech Connect

The purpose of the Craig Wood Fired Boiler Project is to use waste wood from local sawmilling operations to provide heat to local public buildings, in an effort to reduce the cost of operating those buildings, and put to productive use a byproduct from the wood milling process that otherwise presents an expense to local mills. The scope of the project included the acquisition of a wood boiler and the delivery systems to feed wood fuel to it, the construction of a building to house the boiler and delivery systems, and connection of the boiler facility to three buildings that will benefit from heat generated by the boiler: the Craig Aquatic Center, the Craig Elementary School, and the Craig Middle School buildings.

Jonathan Bolling

2009-03-02T23:59:59.000Z

183

Mutiny on the Bounty or Bountiful Mutants? Diversity and Composition of Wood-Decaying Macrofungi on Hibiscus Tiliaceus Wood in French Polynesia  

E-Print Network (OSTI)

B. G. Jonsson. 1995. Wood-inhabiting fungi and substratumand S. C. Watkinson. 1995. Wood decomposition, higher fungi,combative interaction between wood-decaying basidiomycetes.

Wheaton, Felicia

2006-01-01T23:59:59.000Z

184

Alternative System for Wood Carbonization.  

E-Print Network (OSTI)

??The production of charcoal is a activities which depends on the raw material, labor and production system. The raw material needs to possess some characteristics… (more)

ClaudinÃia Olimpia de Assis

2007-01-01T23:59:59.000Z

185

HIGH RESOLUTION MICROTOMOGRAPHY FOR DENSITY AND SPATIAL INFORMATION ABOUT WOOD STRUCTURES.  

DOE Green Energy (OSTI)

Microtomography has successfully been used to characterize loss of structural integrity of wood. Tomographic images were generated with the newly developed third generation x-ray computed microtomography (XCMT) instrument at the X27A beamline at the National Synchrotron Light Source (NSLS). The beamline is equipped with high-flux x-ray monochromator based on multilayer optics developed for this application. The sample is mounted on a translation stage with which to center the sample rotation, a rotation stage to perform the rotation during data collection and a motorized goniometer head for small alignment motions. The absorption image is recorded by a single-crystal scintillator, an optical microscope and a cooled CCD array detector. Data reconstruction has provided three-dimensional geometry of the heterogeneous wood matrix in microtomographic images. Wood is a heterogeneous material composed of long lignocellulose vessels. Although wood is a strong natural product, fungi have evolved chemical systems that weaken the strength properties of wood by degrading structural vessels. Tomographic images with a resolution of three microns were obtained nonintrusively to characterize the compromised structural integrity of wood. Computational tools developed by Lindquist et al (1996) applied to characterize the microstructure of the tomographic volumes.

ILLMAN,B.

1999-07-22T23:59:59.000Z

186

Characterization of Waste Tar Associated with Abandoned Wood Chemical Plant Sites in Northwest Pennsylvania, USA  

SciTech Connect

Over 70 wood chemical plants operated in northern Pennsylvania between ca. 1890 and 1950, all located within 72 km of the New York state border. Their original purpose was to salvage the small unwanted hardwood trees left behind by the lumber mills, and to make charcoal, calcium acetate and methanol for a number of industrial uses via destructive distillation. At many old wood chemical plant sites, unknown quantities of wood tar remain as a residual contaminant and pose a pollution threat to aquatic life in nearby streams. Research on the composition and properties of residual wood tars from five abandoned industrial sites in Pennsylvania are described. Weathered wood tars were more viscous and contained fewer volatile and semivolatile organic compounds than did soil-buried tars. Phenol, 2-methylphenol (o-cresol), 4-methylphenol (p-cresol), and 2, 4-dimethylphenol were found in all sampled tars. These water-soluble phenolic compounds were released quasi-instantaneously in aqueous solution, followed by a slower rate of release, consistent with the behavior of similar compounds in other dense non-aqueous liquids. Air-exposed wood tar deposits developed a hard crust, which contained fewer volatiles and semivolatiles and had a higher softening point than other samples. These tars eroded to form a powdered soil colonized by lichens and mosses. Residual wood tar material found at one site was shown to be thermally altered, likely during the historical destruction of the chemical plant by fire. Recovered wood tar wastes have a relatively high heating value and may have use as a potential, but limited, alternate energy source.

Edendorn, H.M.; Severson, D. (Allegheny Institute of Natural History, Bradford, PA)

2007-07-01T23:59:59.000Z

187

Economics of modifying harvesting systems to recover energy wood  

SciTech Connect

Recent interest in the recovery of previously underutilized logging residues for energy has stimulated the development of a variety of technologies for bringing this resource to market. The most promising approach for the independent contractor working the south eastern United States is to incorporate residue recovery equipment into his existing harvesting system. Computer simulation was used to assess the potential impact of adding small chippers or residue balers to three common harvesting systems. The systems are used in pine plantations, and mixed pine hardwood and upland hardwood stands. Changes in both operating costs and capital used were used to measure the effect of moving from conventional products to total energy wood harvests and capturing residues for energy in conjunction with conventional products. Incremental analysis was used to assess the operating cost per ton and capitalization per ton of annual production associated with the addition of the residue recovery capability. In nearly every case the incremental cost per ton and the incremental capitalization per ton associated with adding capability (for recovering wood residues for energy) to conventional harvesting systems were considerably less than for establishing systems of the same configuration (to produce energy wood only). The flow of conventional products must not be interrupted by the residue recovery process. Clearcutting or thinning operations conducted primarily for the production of enery wood did not appear to be economical on any stand, given 1979 residue values, unless a proportion of the large diameter trees are merchandized as conventional products. This statement, of course, must take into account that the cost used for both conventional products and the full tree chips were based upon 1979 pulp chip prices. If the alternative value of this material as fuel rises above its current value for fiber, this situation may change.

Stuart, W.B.; Porter, C.D.; Walbridge, T.A.; Oderwald, R.G.

1981-08-01T23:59:59.000Z

188

Making Steel Framing as Thermally Efficient as Wood  

E-Print Network (OSTI)

In many world regions like North America and Scandinavia wood framing is dominant technology for residential buildings. During last two decades several companies around the world started to promote a low-gage steel framing for residential and commercial buildings. Steel framing has many advantages over wood framing; strength, low weight, dimensional stability, resistance to termite damage, almost 100% recycleability, etc .. However because of several reasons an application of steel as a framing material in US residential building market is relatively low. Steel industry has noticed much more success on commercial building market which is not as rigorous regarding thermal efficiency and energy conservation. Steel framing has one significant disadvantage over wood; Steel members conduct heat extremely well. This effect is known as thermal bridging, and it can sharply reduce a wall's effective Rvalue. The simplest and most common way to overcome this problem is to block the path of heat flow with rigid foam insulation. Adding rigid foam insulation not only increases the whole wall's R-value, but it also reduces the temperature difference between the center of the cavity and the stud area, which cuts down on the possibility of black stains forming from dirt getting asymmetrically attracted to cold spots on a wall's surface. However, rigid foam insulation is an expensive solution. Several material configurations were developed in the past to increase thermal effectiveness of steel-framed structures. This paper is focused on most common options of thermal improvements of steels framed walls. They were as follow: 1) diminishing the contact area between the studs and exterior sheathing materials, 2) reducing the steel stud web area, 3) replacing the steel web with a less conductive material, and 4) placing foam insulation in locations where the thermal shorts are most critical. Researchers at Oak Ridge National Laboratory (ORNL) have utilized both hot box testing and computer simulations in aim to optimize thermal design of steel stud walls.. While examining several material options, ORNL's BTC was also striving to develop energy-efficient steel stud wall technologies that would enable steel-stud walls to beat the performance of traditional 2 x 6 wood stud walls. Several, most current, ORNL developments in steel framing are presented below.

Kosny, J.; Childs, P.

2002-01-01T23:59:59.000Z

189

Supporting rural wood industry through timber utilization research. Research paper  

SciTech Connect

The report evaluates the potential impact of USDA Forest Service wood utilization and wood energy research on rural employment and income. Recent projections suggest employment will decrease in many forest products industries, such as softwood sawmilling, but will eventually increase in softwood plywood and reconstituated panel mills. Forest products industries expected to provide wages exceeding the average manufacturing production wage include logging, softwood sawmills, millwork, softwood plywood--veneer, structural wood members, particle-board, wood partitions, pulp mills, paper mills, and paperboard mills. Industries expected to pay 90 percent of the average manufacturing production wage include wood kitchen cabinets, mobile homes, prefabricated wood buildings, and wood preservatives.

Skog, K.

1991-10-01T23:59:59.000Z

190

URBAN WOOD/COAL CO-FIRING IN THE BELLEFIELD BOILERPLANT  

DOE Green Energy (OSTI)

An Environmental Questionnaire for the demonstration at the Bellefield Boiler Plant (BBP) was submitted to the national Energy Technology Laboratory. An R&D variance for the air permit at the BBP was sought from the Allegheny County Health Department (ACHD). R&D variances for the solid waste permits at the J. A. Rutter Company (JARC), and Emery Tree Service (ETS) were sought from the Pennsylvania Department of Environmental Protection (PADEP). Construction wood was acquired from Thompson Properties and Seven D Corporation. Verbal authorizations were received in all cases. Memoranda of understanding were executed by the University of Pittsburgh with BBP, JARC and ETS. Construction wood was collected from Thompson Properties and from Seven D Corporation. Forty tons of pallet and construction wood were ground to produce BioGrind Wood Chips at JARC and delivered to Mon Valley Transportation Company (MVTC). Five tons of construction wood were hammer milled at ETS and half of the product delivered to MVTC. Blends of wood and coal, produced at MVTC by staff of JARC and MVTC, were shipped by rail to BBP. The experimental portion of the project was carried out at BBP in late March and early April 2001. Several preliminary tests were successfully conducted using blends of 20% and 33% wood by volume. Four one-day tests using a blend of 40% wood by volume were then carried out. Problems of feeding and slagging were experienced with the 40% blend. Light-colored fly ash was observed coming from the stack during all four tests. Emissions of SO{sub 2}, NOx and total particulates, measured by Energy Systems Associates, decreased when compared with combusting coal alone. A procedure for calculating material and energy balances on BBP's Boiler No.1 was developed, using the results of an earlier compliance test at the plant. Material and energy balances were then calculated for the four test periods. Boiler efficiency was found to decrease slightly when the fuel was shifted from coal to the 40% blend. Neither commercial production of sized urban waste wood for the energy market in Pittsburgh nor commercial cofiring of wood/coal blends at BBP are anticipated in the near future.

James T. Cobb Jr.; Gene E. Geiger; William W. Elder III; William P. Barry; Jun Wang; Hongming Li

2004-04-08T23:59:59.000Z

191

Inside the guts of wood-eating catfishes: can they digest wood?  

E-Print Network (OSTI)

T (2009) Non-native suckermouth armored catWshes in Florida:Loricariidae), wood-eating armored catWshes from Tropical

German, Donovan P.

2009-01-01T23:59:59.000Z

192

REDD+ Training Materials | Open Energy Information  

Open Energy Info (EERE)

REDD+ Training Materials REDD+ Training Materials Jump to: navigation, search Tool Summary LAUNCH TOOL Name: REDD+ Training Materials Agency/Company /Organization: German Agency for International Cooperation (GIZ), World Wildlife Fund, The Rainforest Alliance, The Nature Conservancy, Conservation International Sector: Land Focus Area: Forestry Resource Type: Training materials, Lessons learned/best practices Website: www.conserveonline.org/workspaces/trainingmaterials REDD+ Training Materials Screenshot References: REDD+ Training [1] Overview " Reducing Emissions from Deforestation and forest Degradation and the role of conservation, sustainable management of forests, and enhancement of forest carbon stocks (REDD+) is a concept that has been gaining momentum in climate change policy negotiations both internationally and at the national

193

Biomass Energy - Focus on Wood Waste  

NLE Websites -- All DOE Office Websites (Extended Search)

application for wood waste as a fuel is in the co-firing of conventional coal-fired boilers, which means using biomass as a supplementary energy source in high- efficiency...

194

Arbuthnott Wood Pellets Ltd | Open Energy Information  

Open Energy Info (EERE)

Arbuthnott Wood Pellets Ltd Arbuthnott Wood Pellets Ltd Jump to: navigation, search Name Arbuthnott Wood Pellets Ltd Place Kincardineshire, Scotland, United Kingdom Zip AB30 1PA Product Wood pellet producer. Coordinates 56.932781°, -2.42531° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":56.932781,"lon":-2.42531,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

195

Wood Burning Combined Cycle Power Plant  

E-Print Network (OSTI)

A combined cycle power plant utilizing wood waste products as a fuel has been designed. This plant will yield a 50% efficiency improvement compared to conventional wood-fueled steam power plants. The power plant features an externally-fired gas turbine combined cycle system that obtains its heat input from a high temperature, high pressure ceramic air heater burning wood waste products as a fuel. This paper presents the results of the design study including the cycle evaluation and a description of the major components of the power plant. The cycle configuration is based on maximum fuel efficiency with minimum capital equipment risk. The cycle discussion includes design point performance of the power plant. The design represents a significant step forward in wood-fueled power plants.

Culley, J. W.; Bourgeois, H. S.

1984-01-01T23:59:59.000Z

196

Wood-Burning Heating System Deduction  

Energy.gov (U.S. Department of Energy (DOE))

This statute allows individual taxpayers a deduction for the purchase and installation of a wood-burning heating system. The deduction is equal to the total cost of purchase and installation for...

197

The Texarkana Wood Preserving Company Superfund site  

E-Print Network (OSTI)

is a former wood-treating site located in Texas that treated various wood products with chemical preservatives. These activities left behind contaminated soil and sludge, that led to contaminated groundwater. In 1990 Environmental Protection Agency (EPA) selected incineration as the means to clean up contaminated soil at this site. In 1994 Congressman Jim Chapman (D-Texas) asked the Office of Technology Assessment (OTA) to review alternative technologies that might be used instead of incineration at the Texarkana site. A second, separate study to assess the safety of incineration was also requested by Representative Chapman. This report reviews technologies available for hazardous waste cleanup at wood-treating sites throughout the United States. OTA found that there are many Superfund wood-treatment sites located in this country that are very similar in terms of the contaminants

Roger C. Herdman; Frank Avvisato

1995-01-01T23:59:59.000Z

198

Chemistry and stoichiometry of wood liquefaction  

DOE Green Energy (OSTI)

The approximate stoichiometry of liquefaction, from data of two PDU runs and a laboratory run is Wood (100 g) + CO (0.1 - 0.4 Mol) ..-->.. CO/sub 2/ (0.5 - 1.0 Mol) + H/sub 2/O (0.4 - 0.8 Mol) + Product (55 - 64 g). Product includes wood oil, water soluble organics and residues. Water is formed by decomposition, carbon dioxide by decomposition and reduction of wood oxygen by CO. Aqueous products include many carboxylic acids plus a roughly equal percentage of non-acids. The wood oil is divided into a neutral fraction and three phenolic fractions of varying molecular weight. Some specific compounds found in water and oil phases are listed.

Davis, H.G.; Kloden, D.J.; Schaleger, L.L.

1981-06-01T23:59:59.000Z

199

Estimating the greenhouse gas benefits of forestry projects: A Costa Rican Case Study  

SciTech Connect

If the Clean Development Mechanism proposed under the Kyoto Protocol is to serve as an effective means for combating global climate change, it will depend upon reliable estimates of greenhouse gas benefits. This paper sketches the theoretical basis for estimating the greenhouse gas benefits of forestry projects and suggests lessons learned based on a case study of Costa Rica's Protected Areas Project, which is a 500,000 hectare effort to reduce deforestation and enhance reforestation. The Protected Areas Project in many senses advances the state of the art for Clean Development Mechanism-type forestry projects, as does the third-party verification work of SGS International Certification Services on the project. Nonetheless, sensitivity analysis shows that carbon benefit estimates for the project vary widely based on the imputed deforestation rate in the baseline scenario, e.g. the deforestation rate expected if the project were not implemented. This, along with a newly available national dataset that confirms other research showing a slower rate of deforestation in Costa Rica, suggests that the use of the 1979--1992 forest cover data originally as the basis for estimating carbon savings should be reconsidered. When the newly available data is substituted, carbon savings amount to 8.9 Mt (million tones) of carbon, down from the original estimate of 15.7 Mt. The primary general conclusion is that project developers should give more attention to the forecasting land use and land cover change scenarios underlying estimates of greenhouse gas benefits.

Busch, Christopher; Sathaye, Jayant; Sanchez Azofeifa, G. Arturo

2000-09-01T23:59:59.000Z

200

Short rotation Wood Crops Program  

DOE Green Energy (OSTI)

This report synthesizes the technical progress of research projects in the Short Rotation Woody Crops Program for the year ending September 30, 1989. The primary goal of this research program, sponsored by the US Department of Energy's Biofuels and Municipal Waste Technology Division, is the development of a viable technology for producing renewable feedstocks for conversion to biofuels. One of the more significant accomplishments was the documentation that short-rotation woody crops total delivered costs could be $40/Mg or less under optimistic but attainable conditions. By taking advantage of federal subsidies such as those offered under the Conservation Reserve Program, wood energy feedstock costs could be lower. Genetic improvement studies are broadening species performance within geographic regions and under less-than-optimum site conditions. Advances in physiological research are identifying key characteristics of species productivity and response to nutrient applications. Recent developments utilizing biotechnology have achieved success in cell and tissue culture, somaclonal variation, and gene-insertion studies. Productivity gains have been realized with advanced cultural studies of spacing, coppice, and mixed-species trials. 8 figs., 20 tabs.

Wright, L.L.; Ehrenshaft, A.R.

1990-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Isolation of levoglucosan from lignocellulosic pyrolysis oil derived from wood or waste newsprint  

DOE Patents (OSTI)

A method is provided for preparing high purity levoglucosan from lignocellulosic pyrolysis oils derived from wood or waste newsprint. The method includes reducing wood or newsprint to fine particle sizes, treating the particles with a hot mineral acid for a predetermined period of time, and filtering off and drying resulting solid wood or newsprint material; pyrolyzing the dried solid wood or newsprint material at temperatures between about 350 and 375 C to produce pyrolysis oils; treating the oils to liquid-liquid extraction with methyl isobutyl ketone to remove heavy tar materials from the oils, and to provide an aqueous fraction mixture of the oils containing primarily levoglucosan; treating the aqueous fraction mixtures with a basic metal salt in an amount sufficient to elevate pH values to a range of about 12 to about 12.5 and adding an amount of the salt in excess of the amount needed to obtain the pH range to remove colored materials of impurities from the oil and form a slurry, and freeze-drying the resulting slurry to produce a dry solid residue; and extracting the levoglucosan from the residue using ethyl acetate solvent to produce a purified crystalline levoglucosan. 2 figs.

Moens, L.

1995-07-11T23:59:59.000Z

202

Isolation of levoglucosan from lignocellulosic pyrolysis oil derived from wood or waste newsprint  

DOE Patents (OSTI)

A method is provided for preparing high purity levoglucosan from lignocellulosic pyrolysis oils derived from wood or waste newsprint. The method includes reducing wood or newsprint to fine particle sizes, treating the particles with a hot mineral acid for a predetermined period of time, and filtering off and drying resulting solid wood or newsprint material; pyrolyzing the dried solid wood or newsprint material at temperatures between about 350.degree. and 375.degree. C. to produce pyrolysis oils; treating the oils to liquid-liquid extraction with methyl isobutyl ketone to remove heavy tar materials from the oils, and to provide an aqueous fraction mixture of the oils containing primarily levoglucosan; treating the aqueous fraction mixtures with a basic metal salt in an amount sufficient to elevate pH values to a range of about 12 to about 12.5 and adding an amount of the salt in excess of the amount needed to obtain the pH range to remove colored materials of impurities from the oil and form a slurry, and freeze-drying the resulting slurry to produce a dry solid residue; and extracting the levoglucosan from the residue using ethyl acetate solvent to produce a purified crystalline levoglucosan.

Moens, Luc (Lakewood, CO)

1995-01-01T23:59:59.000Z

203

How Wood Chip Size Affects Pretreatment Effectiveness of Woody Biomass for Biological Processing  

E-Print Network (OSTI)

explosion pretreatment of wood: effect of chip size, acid,In: Soltes, E.J. (Ed. ), Wood and Agriculture Residues –D. , Wegener, G. , 1984. Wood: Chemistry, Ultrastructure,

Tam, Jerry

2013-01-01T23:59:59.000Z

204

PATTERNS OF DIFFUSIBILITY OF LIGNIN AND CARBOHYDRATE DEGRADING SYSTEMS IN WOOD-ROTTING FUNGI  

E-Print Network (OSTI)

selected Delignification of wood chips by mutant white-rotTemperature relations of wood-destroying fungi. Kaneshiro.phenoloxidases of selected wood-decaying basidiomycetes. J,

Rosenberg, S. L.

2011-01-01T23:59:59.000Z

205

URBAN WOOD/COAL CO-FIRING IN THE BELLEFIELD BOILERPLANT  

DOE Green Energy (OSTI)

During the third quarter, important preparatory work was continued so that the experimental activities can begin early in the fourth quarter. Authorization was awaited in response to the letter that was submitted to the Allegheny County Health Department (ACHD) seeking an R&D variance for the air permit at the Bellefield Boiler Plant (BBP). Verbal authorizations were received from the Pennsylvania Department of Environmental Protection (PADEP) for R&D variances for solid waste permits at the J. A. Rutter Company (JARC), and Emery Tree Service (ETS). Construction wood was acquired from Thompson Properties and Seven D Corporation. Forty tons of pallet and construction wood were ground to produce BioGrind Wood Chips at JARC and delivered to Mon Valley Transportation Company (MVTC). Five tons of construction wood were milled at ETS and half of the product delivered to MVTC. Discussions were held with BBP and Energy Systems Associates (ESA) about the test program. Material and energy balances on Boiler No.1 and a plan for data collection were prepared. Presentations describing the University of Pittsburgh Wood/Coal Co-Firing Program were provided to the Pittsburgh Chapter of the Pennsylvania Society of Professional Engineers, and the Upgraded Coal Interest Group and the Biomass Interest Group (BIG) of the Electric Power Research Institute (EPRI). An article describing the program appeared in the Pittsburgh Post-Gazette. An application was submitted for authorization for a Pennsylvania Switchgrass Energy and Conservation Program.

James T. Cobb, Jr.; Gene E. Geiger; William W. Elder III; William P. Barry; Jun Wang; Hongming Li

2001-08-21T23:59:59.000Z

206

Simple and inexpensive method of wood pellets macro-porosity measurement  

Science Conference Proceedings (OSTI)

A novel simplified stereometric measurement method for determining the macro-porosity of wood pellets through geometrical approach was successfully developed and tested. The irregular ends of pellets of circular cross-section were sanded flat so that their geometry becomes cylinder and their volumes evaluated using mensuration formula. Such formed cylindrical pellets were loose or tap filled to selected volumes to evaluate the macro-porosity and the constant specific weight. The method was extended to evaluate actual wood pellets properties. Overall macro-porosity of actual wood pellets was determined as 41.0 2.5% and 35.5 2.7%, mean bulk density as and, and classified as Class-3:Medium and Class-3&4:Medium to Low for loose and tapped fills, respectively. Hausner ratio and Carr s compressibility index classify wood pellets as freely flowing. The developed stereometric method can be used as a handy inexpensive laboratory procedure to estimate the macro-porosity of different types and makes of wood pellets and other similar packaged materials.

Igathinathane, C. [North Dakota State University; Tumuluru, J.S. [Idaho National Laboratory (INL); Sokhansanj, Shahabaddine [ORNL; Bi, X.T. [University of British Columbia, Vancouver; Lim, C. Jim [University of British Columbia, Vancouver; Melin, Staffan [University of British Columbia, Vancouver; Mohammad, E. [University of British Columbia, Vancouver

2010-01-01T23:59:59.000Z

207

Transcriptome and Biochemical Analyses of Fungal Degradation of Wood  

SciTech Connect

Lignocellulosic accounts for a large percentage of material that can be utilized for biofuels. The most costly part of lignocellulosic material processing is the initial hydrolysis of the wood which is needed to circumvent the lignin barrier and the crystallinity of cellulose. Enzymes will play an increased role in this conversion in that they potentially provide an alternative to costly and caustic high temperature and acid treatment. The increasing use of enzymes in biotechnology is facilitated by both continued improvements in enzyme technology but also in the discovery of new and novel enzymes. The present proposal is aimed at identifying the enzymes which are known to depolymerize woody biomass. Fundamental understanding of how nature gains access to cellulose and hemicellulose will impact all applications. Because fungi are the only known microbes capable of circumventing the lignin barrier, knowledge of the enzyme they use is of great potential for biofuel processing. Nature has evolved different fungal mechanisms for enzymatic hydrolysis of wood. Most notable are the white-rot fungi (wrf) and the brown-rot fungi (brf). This proposed research aims at determining the complete transcriptome of three wrf and two brf to determine the enzymes involved in lignocellulose degradation. The transcriptome work will be supported by enzyme characterization (and zymograms) and finally analysis of the lignin component to determine the mode of lignin modification. In this proposed research, we hypothesize that: 1) Determination of the complete transcriptome of closely related white and brown rot fungi will lead to knowledge of the relevant enzymes involved in wood degradation. 2) Knowledge of the extracellular transcriptome and the mechanism of wood decay can only be obtained if the products of the decay are known. As such, characterization of the lignin oxidation products will correlate the enzymes involved (obtained from the transcriptome) to the lignin oxidation products. The Department of Energy has sequenced the P. chrysosporium genome and has approved the sequencing of the genome of the closely-related brown rot fungus P. placenta. This comparative genomics approach will yield important information on differences between these two fungi. Analysis of gene unique to each fungus (which have been lost or gained) can potentially lead to determining the enzymes which are responsible for each type of decay. This comparison, however, would not be complete without comparing the transcriptome and the proteome/enzymes. Comparative genomics may tell us which genes may be important, but it will not tell us when these genes are expressed, at what levels and will not necessarily tell us what these genes do.

Tien, Ming

2009-03-14T23:59:59.000Z

208

Carol A. Wood Contract Specialist  

E-Print Network (OSTI)

. Equipment has been forecasted to be purchased in the next phase. #12;Being purchased for the NIST such as used for photoanodes, supercapacitors, battery electrodes, hydrogen storage materials and solar cells

Magee, Joseph W.

209

Wood Fuel LP | Open Energy Information  

Open Energy Info (EERE)

Fuel LP Fuel LP Jump to: navigation, search Logo: Wood Fuel LP Name Wood Fuel LP Address 5900 Haynesworth Lane Place Houston, Texas Zip 77034 Sector Biomass Product Wood by-products consulting and marketing Website http://www.woodfuel.com/ Coordinates 29.6221328°, -95.1872605° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":29.6221328,"lon":-95.1872605,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

210

Wood and Derived Fuels | OpenEI  

Open Energy Info (EERE)

1 1 Varnish cache server Browse Upload data GDR 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142288361 Varnish cache server Wood and Derived Fuels Dataset Summary Description Annual commodity balances (supply, consumption) for renewables and waste in the UK from 1998 to 2009. Published as part of the Digest of UK energy statistics (DUKES), by the UK Department of Energy & Climate Change (DECC). Waste includes: wood waste, farm waste, sewage gas, landfill gas, waste and tyres. Renewables includes: wood, plant-based biomass, geothermal and active solar heat, hydro, wind, wave and tidal, and liquid biofuels. Source UK Department of Energy and Climate Change (DECC) Date Released July 29th, 2010 (4 years ago)

211

Chemical Emissions of Residential Materials and Products: Review of Available Information  

E-Print Network (OSTI)

wood materials used (i.e. plywood, OSB, MDB, cabinetry) (regulation is applicable to plywood, particle board, medium-Carpet, polyurethane foam Plywood Laminate w/ particle board

Willem, Henry

2010-01-01T23:59:59.000Z

212

Environmental-performance research priorities: Wood products. Final report  

Science Conference Proceedings (OSTI)

This report describes a research plan to establish environmental, energy, and economic performance measures for renewable building materials, and to identify management and technology alternatives to improve environmental performance in a cost-effective manner. The research plan is designed to: (1) collect environmental and economic data on all life-cycle stages of the materials, (2) ensure that the data follows consistent definitions and collection procedures, and (3) develop analytical procedures for life-cycle analysis to address environmental performance questions. The research will be subdivided into a number of individual project modules. The five processing stages of wood used to organize the research plan are: (1) resource management and harvesting; (2) processing; (3) design and construction of structures; (4) use, maintenance, and disposal; and (5) waste recycling. Individual research module descriptions are provided in the report, as well as assessment techniques, research standards and protocol, and research management. 13 refs., 5 figs., 3 tabs.

NONE

1998-01-15T23:59:59.000Z

213

OpenEI - Wood and Derived Fuels  

Open Energy Info (EERE)

UK Energy Statistics: UK Energy Statistics: Renewables and Waste, Commodity Balances (2010) http://en.openei.org/datasets/node/82 Annual commodity balances (supply, consumption) for renewables and waste in the UK from 1998 to 2009. Published as part of the Digest of UK energy statistics (DUKES), by the UK Department of Energy & Climate Change (DECC). Waste includes: wood waste, farm waste, sewage gas, landfill gas, waste and tyres. Renewables includes: wood, plant-based biomass, geothermal and active solar heat, hydro, wind, wave and tidal, and liquid biofuels.

License
Type of

214

International Trade of Wood Pellets (Brochure)  

DOE Green Energy (OSTI)

The production of wood pellets has increased dramatically in recent years due in large part to aggressive emissions policy in the European Union; the main markets that currently supply the European market are North America and Russia. However, current market circumstances and trade dynamics could change depending on the development of emerging markets, foreign exchange rates, and the evolution of carbon policies. This fact sheet outlines the existing and potential participants in the wood pellets market, along with historical data on production, trade, and prices.

Not Available

2013-05-01T23:59:59.000Z

215

Marin County - Wood Stove Replacement Rebate Program (California...  

Open Energy Info (EERE)

DSIRE1 Summary The County of Marin has created a rebate program to encourage homeowners to remove or replace non-EPA certified wood-burning heaters (wood stoves and...

216

Commercial Demonstration of Wood Recovery, Recycling, and Value Adding Technologies  

DOE Green Energy (OSTI)

This commercial demonstration project demonstrated the technical feasibility of converting low-value, underutilized and waste stream solid wood fiber material into higher valued products. With a growing need to increase product/production yield and reduce waste in most sawmills, few recovery operations and practically no data existed to support the viability of recovery operations. Prior to our efforts, most all in the forest products industry believed that recovery was difficult, extremely labor intensive, not cost effective, and that recovered products had low value and were difficult to sell. This project provided an opportunity for many within the industry to see through demonstration that converting waste stream material into higher valued products does in fact offer a solution. Our work, supported by the U.S. Department of Energy, throughout the project aimed to demonstrate a reasonable approach to reducing the millions of recoverable solid wood fiber tons that are annually treated as and converted into low value chips, mulch and fuel. Consequently sawmills continue to suffer from reduced availability of forest resources, higher raw material costs, growing waste disposal problems, increased global competition, and more pressure to operate in an Environmentally Friendly manner. It is our belief (based upon the experience of this project) that the successful mainstreaming of the recovery concept would assist in alleviating this burden as well as provide for a realistically achievable economic benefit to those who would seriously pursue the concept and tap into the rapidly growing ''GREEN'' building marketplace. Ultimately, with participation and aggressive pursuit of the recovery concept, the public would benefit in that: (1) Landfill/disposal waste volume could be reduced adding greater life to existing municipal landfill sites thereby minimizing the need to prematurely license and open added facilities. Also, there would be a cost avoidance benefit associated to what would have been the added municipal (community) management costs involved with maintaining closed landfills. (2) With greater quantities of recovered material being returned to and integrated into manufacturing and the marketplace, reduced demand upon virgin wood sources could help lead the way to promoting improved relations and environmental balance between producers and consumers further expanding the value of our natural resource without adding environmental burden.

Auburn Machinery, Inc.

2004-07-15T23:59:59.000Z

217

Superheater Tube Corrosion in Wood Gasifier Ash Deposits  

DOE Green Energy (OSTI)

The upper operating temperature of tubes in heat exchangers/steam generators is strongly influenced by the degradation that can occur because of the reaction of the exchanger/generator tubing with the deposits that accumulate on the surface of the tubes. In fact, severe corrosion has been observed in some biomass fired systems, particularly with elevated potassium and chlorine concentrations in the deposits. Wood gasifiers have recently been and are currently being constructed at several sites in North America. In these systems, the syngas is burned to produce steam and the performance of the heat exchanger tubes under ash deposits is of great concern. As temperatures of the heat exchangers are increased in an effort to increase their operating efficiency, the performance of the tubes is of greater interest. The corrosion behavior of alloy steel tubes as a function of temperature has been investigated by exposing samples of selected alloys to ash collected from the steam generator fired by syngas produced in wood gasifiers. This study compares corrosion rates from laboratory exposures of synthesis gas and ash at 500 C and 600 C. This study investigated the material performance of four ferritic steels and one austenitic steel exposed to conditions expected on the fireside of a wood gasifier. The purpose of this study was to identify an effective method for determining material performance for samples exposed to both the process gas and the fly ash that is typically observed within the steam generator for times up to 1000 hours. Mass changes were measured for all of the samples, but this information can be misleading concerning material performance due to the difficulty in sufficiently cleaning the samples after exposure in the ash. Therefore, small cross sections of the samples were collected and imaged using optical microscopy. Oxide thicknesses were measured along with metal losses. The metal loss information provides a clear indication of material performance. The metal loss rates for the ferritic steels at 500 C were almost half of those observed at 600 C and the rates decreased with increasing exposure time. It was also reported that the metal loss rates generally decrease with increasing chromium concentration.

Bestor, Michael A [ORNL; Keiser, James R [ORNL; Meisner, Roberta A [University of Tennessee, Knoxville (UTK) & Oak Ridge National Laboratory (ORNL)

2011-01-01T23:59:59.000Z

218

The potential of wood residue streams for industrial wood pellet production in the Baltic Countries and Poland.  

E-Print Network (OSTI)

??Currently most solid biomass in the European Union (EU-27) is made from high grade secondary wood residues, e.g. clean saw dust and wood chips. The… (more)

Jong, B. de

2012-01-01T23:59:59.000Z

219

Availability of wood as a heating fuel for Colorado  

SciTech Connect

As Colorado homeowners turn to wood as an alternative space-heating fuel, supplies--particularly along the heavily populated Front Range--dwindle. The report reexamines the resource base and presents alternatives to wood in the event of a shortage (for instance, many wood stoves can burn coal as well).

1982-01-01T23:59:59.000Z

220

Wood Fuel Future: The Potential Web Text December 2010  

E-Print Network (OSTI)

and power, the wood products industry and major independent power producers also have significant production of heat and power. Table 3.1 Canadian Wood Residue Heat & Power Generation - 2003 13 Forest Products SAWMILLS LTD LACRETE 50,000 TONNE WOOD PELLET PRODUCTION IN WESTERN CANADA 2004 / 2005 PINNACLE PEL LET INC

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

The ambient wood journals: replaying the experience  

Science Conference Proceedings (OSTI)

The Ambient Wood project aims to facilitate a learning experience using an adaptive infrastructure in an outdoor environment. This involves sensor technology, virtual world orchestration, and a wide range of devices ranging from hand-held computers to ... Keywords: adaptive infrastructure, consolidation, record and replay, storytelling

Mark J. Weal; Danius T. Michaelides; Mark K. Thompson; David C. DeRoure

2003-08-01T23:59:59.000Z

222

Energie-Cits 2001 BIOMASS-WOOD  

E-Print Network (OSTI)

Energie-Cités 2001 BIOMASS-WOOD Power plant LIENZ Austria By the year 2010, 12% of the gross inland this goal, intensified use needs to be made of biomass, both for heating purposes and for power generation to this rule. Thus, for instance, the town of Lienz started up the largest biomass facility of Austria

223

Energie-Cits 2001 BIOMASS -WOOD  

E-Print Network (OSTI)

Energie-Cités 2001 BIOMASS - WOOD Gasification / Cogeneration ARMAGH United Kingdom Gasification is transferring the combustible matters in organic waste or biomass into gas and pure char by burning the fuel via it allows biomass in small-scaled engines and co-generation units ­ which with conventional technologies

224

Successful biomass (wood pellets ) implementation in  

E-Print Network (OSTI)

Regional Energy centres in Estonia This presentation will cover Regional Energy Centres in Estonia ! Supply Regional Energy Centres in Estonia Supply of primary energy in Estonia Regional Energy Centres in Estonia of primary energy in Estonia ! Wood fuels production ! Pellet firing projects in Estonia ­ SIDA Demo East

225

Wood combustion systems: status of environmental concerns  

DOE Green Energy (OSTI)

This document addresses the uncertainties about environmental aspects of Wood Combustion Systems that remain to be resolved through research and development. The resolution of these uncertainties may require adjustments in the technology program before it can be commercialized. The impacts and concerns presented in the document are treated generically without reference to specific predetermined sites unless these are known. Hence, site-specific implications are not generally included in the assessment. The report consists of two main sections which describe the energy resource base involved, characteristics of the technology, and introduce the environmental concerns of implementing the technology; and which review the concerns related to wood combustion systems which are of significance for the environment. It also examines the likelihood and consequence of findings which might impede wood commercialization such as problems and uncertainties stemming from current or anticipated environmental regulation, or costs of potential environmental controls. This document is not a formal NEPA document. Appropriate NEPA documentation will be prepared after a formal wood combustion commercialization program is approved by DOE.

Dunwoody, J.E.; Takach, H.; Kelley, C.S.; Opalanko, R.; High, C.; Fege, A.

1980-01-01T23:59:59.000Z

226

MARKETS FOR FOREST PRODUCTS P F Olsen and Company Ltd January 2002 Warren Forestry Ltd Copyright 2002 1  

E-Print Network (OSTI)

examined are: · predicted demand for wood products, · current sources and predicted levels of supply the demand figures are based on extrapolations of historical trends. The future supply estimates should to China. New Zealand sells wood to the USA and Chile to Western Europe. As for all commodity trading we

227

Fast Curing of Composite Wood Products  

SciTech Connect

The overall objective of this program is to develop low temperature curing technologies for UF and PF resins. This will be accomplished by: • Identifying the rate limiting UF and PF curing reactions for current market resins; • Developing new catalysts to accelerate curing reactions at reduced press temperatures and times. In summary, these new curing technologies will improve the strength properties of the composite wood products and minimize the detrimental effects of wood extractives on the final product while significantly reducing energy costs for wood composites. This study is related to the accelerated curing of resins for wood composites such as medium density fiberboard (MDF), particle board (PB) and oriented strandboard (OSB). The latter is frequently manufactured with a phenol-formaldehyde resin whereas ureaformaldehyde (UF) resins are usually used in for the former two grades of composite wood products. One of the reasons that hinder wider use of these resins in the manufacturing of wood composites is the slow curing speed as well as inferior bondability of UF resin. The fast curing of UP and PF resins has been identified as an attractive process development that would allow wood to be bonded at higher moisture contents and at lower press temperatures that currently employed. Several differing additives have been developed to enhance cure rates of PF resins including the use of organic esters, lactones and organic carbonates. A model compound study by Conner, Lorenz and Hirth (2002) employed 2- and 4-hydroxymethylphenol with organic esters to examine the chemical basis for the reported enhanced reactivity. Their studies suggested that the enhance curing in the presence of esters could be due to enhanced quinone methide formation or enhanced intermolecular SN2 reactions. In either case the esters do not function as true catalysts as they are consumed in the reaction and were not found to be incorporated in the polymerized resin product. An alternative approach to accelerated PF curing can be accomplished with the addition amines or amides. The later functionality undergoes base catalyzed hydrolysis yielding the corresponding carboxyl ate and free amine which rapidly reacts with the phenolic methylol groups facilitating polymerization and curing of the PF resin (Pizzi, 1997).

Dr. Arthur J. Ragauskas

2006-04-26T23:59:59.000Z

228

Sources of heavy metal contamination in Swedish wood waste used for combustion  

SciTech Connect

In this paper, wood waste (RWW) recovered for heat production in Sweden was studied. Previous research has concluded that RWW contains elevated amounts of heavy metals, causing environmental problems during waste management. This study extends previous work on RWW by analysing which pollution sources cause this contamination. Using existing data on the metal contents in various materials, and the amounts of these materials in RWW, the share of the elevated amounts of metals in RWW that these materials explain was quantified. Six different materials occurring in RWW were studied and the results show that they explain from 70% to 100% of the amounts of arsenic, chromium, lead, copper and zinc in RWW. The most important materials contributing to contamination of RWW are surface-treated wood, industrial preservative-treated wood, plastic and galvanised fastening systems. These findings enable the development and evaluation of strategies aiming to decrease pollution and resource loss from handling RWW. It is argued that source separation and measures taken further downstream from the generation site, such as treatment, need to be combined to substantially decrease the amount of heavy metals in RWW.

Krook, J. [Department of Mechanical Engineering, Linkoeping University, SE-581 83 Linkoeping (Sweden)]. E-mail: joakr@ikp.liu.se; Martensson, A. [Department of Mechanical Engineering, Linkoeping University, SE-581 83 Linkoeping (Sweden); Eklund, M. [Department of Mechanical Engineering, Linkoeping University, SE-581 83 Linkoeping (Sweden)

2006-07-01T23:59:59.000Z

229

Effect of species and wood to bark ratio on pelleting of southern woods  

Science Conference Proceedings (OSTI)

Six common southern hardwoods and loblolly pine were pelleted in a laboratory pellet mill. The pellet furnishes were blended to test the effect of different wood to bark ratios on pellet durability and production rate. Included was a ratio chosen to simulate the wood to bark ratio found in whole-tree chips. This furnish produced good quality pellets for all species tested. Pelleting of the pure wood of hardwoods was not successful; furnish routinely blocked the pellet mill dies. Pure pine wood, however, did produce acceptable pellets. It was noted that, as lignin and extractive content increased above a threshold level, the precentage of fines produced in a pellet durability test increased. Thus, all pine and tupelo wood/bark mixes produces high fines. This reduces the desirability of the pellets in the marketplace. Further research is necessary to confirm this relationship. This study suggests that both tree species and wood/bark ratio affect the durability of pellets and the rate with which they can be produced in a laboratory pellet mill. 9 references.

Bradfield, J.; Levi, M.P.

1984-01-01T23:59:59.000Z

230

Near-term potential of wood as a fuel  

DOE Green Energy (OSTI)

A summary of near-term conversion technologies, which could be used to expand utilization of wood residues and standing forests, is presented. The forest products industry is identified as a principal candidate for expanded wood-fuel use. Sources of wood-fuel are identified and conversion technologies and costs are discussed. Possible near-term incentives to encourage the use of wood as a fuel are examined. These incentives include a retirement tax credit and an investment tax credit. Suppliers of commercial wood conversion systems are identified.

Salo, D.; Gsellman, L.; Medville, D.; Price, G.

1978-08-01T23:59:59.000Z

231

Wood and energy in New Hampshire. Staff report  

SciTech Connect

Telephone surveys of New Hampshire households conducted in 1979 and 1980 indicate a transition to wood heating in response to a series of conventional energy price increases and uncertainty in conventional energy supplies. New Hampshire households consumed 394,000 cords of wood in the winter of 1978-79; 504,000 cords were burnt during the next winter. The airtight wood stove has become the most commonly used wood-burning apparatus. Survey data of residential wood cutting, purchasing, and burning were analyzed by household tenure, wood-burning apparatus, and county. Residential use of wood for energy constitutes a new demand on the forest resource, increases local income and employment, displaces fuel oil and electricity, and may compromise household safety.

Bailey, M.R.; Wheeling, P.R.

1982-06-01T23:59:59.000Z

232

Stress-wave velocity of wood-based panels: Effect of moisture,  

E-Print Network (OSTI)

, Associate Professor, College of Ma- terial Science and Engineering, Northeast Forestry University, China (ghan1@lsu.edu); Professor, School of Renewable Natural Re- sources, Louisiana State University

233

Wood power - its potential in our energy crisis  

Science Conference Proceedings (OSTI)

Wood is meeting about 2% of total U.S. energy needs and may eventually supply up to 7% of our nation's energy. Many forms of direct combustion equipment are available for residential heating and range from supplemental wood-burning stoves to complete house-heating multi-fuel furnaces. A recent survey conducted in New York indicated that one-third of the people contacted used wood for home heating. The total amount of fuelwood used in New York State in 1978 amounted to 1,716,000 standard cords. A Wisconsin study indicates that more than 1.2 million cords of firewood were burned by Wisconsin households during the 1979-80 heating season. A Pennsylvania survey indicated that 22% of single family households used wood for home heating. Corning Glass Works recently conducted a wood-burning stove market survey and found that 18% of all U.S. households own wood-burning stoves. On the basis of cost per unit of heat, wood heat is cheaper than its next closest commonly available rival (fuel oil) and is also cheaper than anthracite coal and electricity. Industrial wood-burning furnaces are commonly incorporated into boiler systems. Nearly 1700 wood-fired boiler systems are in operation in the United States. The economic value of a wood fuel will depend on its heating value and moisture content. For an indsutry considering use of densified wood for fuel, there is a question of whether the added expense is justified by increased ease of handling and improved burning efficiency. Where high sulfur emissions from coal are a problem, burning sulfur-free pellets in combination with coal may be a solution. In Maine a $3 million pellet-making plant is producing 600 tons of pellets per day. Nationally, the overall generating capacity of all known electrical generating plants using wood and wood derived fuels is about 4500 megawatts. Wood can be processed to produce liquid fuels and other chemicals.

Johnson, W.W.

1982-01-01T23:59:59.000Z

234

Furniture wood wastes: Experimental property characterisation and burning tests  

Science Conference Proceedings (OSTI)

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675 to 5105 kcal kg{sup -1} for HHV, and from 3304 to 4634 kcal kg{sup -1} for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM{sub 1} fraction during incomplete industrial wood burning.

Tatano, Fabio [Faculty of Sciences and Technologies, University of Urbino 'Carlo Bo', Campus Scientifico - Sogesta, 61029 Urbino (Italy)], E-mail: fabio.tatano@uniurb.it; Barbadoro, Luca; Mangani, Giovanna; Pretelli, Silvia; Tombari, Lucia; Mangani, Filippo [Faculty of Sciences and Technologies, University of Urbino 'Carlo Bo', Campus Scientifico - Sogesta, 61029 Urbino (Italy)

2009-10-15T23:59:59.000Z

235

Life history and habitat associations of the broad wood cockroach, Parcoblatta lata (Blattaria: Blattellidae) and other native cockroaches in the Coastal Plain of South Carolina.  

DOE Green Energy (OSTI)

Wood cockroaches are an important prey of the red-cockaded woodpecker, Picoides borealis, an endangered species inhabiting pine forests in the southern United States. These woodpeckers forage on the boles of live pine trees, but their prey consists of a high proportion of wood cockroaches, Parcoblatta spp., that are more commonly associated with dead plant material. Cockroach population density samples were conducted on live pine trees, dead snags and coarse woody debris on the ground. The studies showed that snags and logs are also important habitats of wood cockroaches in pine forests.

Horn, Scott; Hanula, James, L.

2002-06-18T23:59:59.000Z

236

Synthesis of SiC nanorods from bleached wood pulp  

DOE Green Energy (OSTI)

Unbleached and bleached soft wood pulps have been used as templates and carbon precursors to produce SiC nanorods. Hydrolyzed tetraethylorthosilicate (TEOS), Silicic acid was infiltrated into the pulps followed by a carbothermal reduction to form SiC nanorods at 1400oC in Ar. Residual carbon formed along with SiC was removed by gasification at 700oC in air. The SiC materials prepared from unbleached pulp were non-uniform SiC with a thick SiO2 coating, while the SiC nanorods prepared from the bleached pulp were uniform and straight with dimensions of 250 nm in diameter and 5.0 mm long. The formation of uniform camelback structure of SiC in the reaction between silica and bleached pulp is attributed to more silica deposited in the amorphous region of cellulose.

Shin, Yongsoon; Wang, Chong M.; Samuels, William D.; Exarhos, Gregory J.

2007-05-01T23:59:59.000Z

237

Research into the pyrolysis of pure cellulose, lignin, and birch wood flour in the China Lake entrained-flow reactor  

DOE Green Energy (OSTI)

This experimental program used the China Lake entrained-flow pyrolysis reactor to briefly investigate the pyrolysis of pure cellulose, pure lignin, and birch wood flour. The study determined that the cellulose and wood flour do pyrolyze to produce primarily gaseous products containing significant amounts of ethylene and other useful hydrocarbons. During attempts to pyrolyze powdered lignin, the material melted and bubbled to block the reactor entrance. The pure cellulose and wood flour produced C/sub 2/ + yields of 12% to 14% by weight, which were less than yields from an organic feedstock derived from processed municipal trash. The char yields were 0.1% by weight from cellulose and 1.5% from birch wood flour - one to two orders of magnitude less than were produced from the trash-derived feedstock. In scanning electron microscope photographs, most of the wood flour char had a sintered and agglomerated appearance, although some particles retained the gross cell characteristics of the wood flour. The appearance of the char particles indicated that the material had once been molten and possibly vapor before it formed spheroidal particles about 1 ..mu..m diameter which agglomerated to form larger char particles. The ability to completely melt or vaporize lignocellulosic materials under conditions of high heating rates has now been demonstrated in a continuous flow reactor and promises new techniques for fast pyrolysis. This char was unexpectedly attracted by a magnet, presumably because of iron contamination from the pyrolysis reactor tube wall. The production of water-insoluble tars was negligible compared to the tars produced from trash-derived feedstock. The production of water-soluble organic materials was fairly low and qualitatively appeared to vary inversely with temperature. This study was of a preliminary nature and additional studies are necessary to optimize ethylene production from these feedstocks.

Diebold, J.

1980-06-01T23:59:59.000Z

238

Pellet stoves wood energy for all  

Science Conference Proceedings (OSTI)

While it`s true that specialized pellet stoves, capable of burning fuels as diverse as reprocessed paper waste and feed corn, are expensive and occasionally clunky, they also represent one of the best hopes for introducing clean burning, reliable renewable energy to those now heating with gas and oil. This article explores the benefits and operation of the stoves including discussions of the following: ecological benefits, combustion, stove venting, ashes, costs, fuels, and the future of wood heat. 1 tab.

NONE

1995-10-01T23:59:59.000Z

239

Inexpensive solar-wood water heating combinations  

SciTech Connect

A promising batch heater recently built and now being tested consists of lengths of eight-inch galvanized culvert pipe painted with semiselective black coating, hooked in series and tied in as part of a passive closed loop, unpressurized solar-wood water heating combination. One 10-foot length of eight-inch culvert contains 14.6 gallons of water. Eight-inch culvert provides a near optimum surface area per unit volume ratio, resulting in quicker, more efficient solar water heating. Moreover, the proposed arrangement minimizes the mixing of hot with cold water as warm water is used, often a problem with many types of batch heaters. Details for constructing this type of batch heater are provided. The system is an unpressurized, closed loop set-up, which means that the same liquid circulates continually from solar heater to wood heater to storage tank heat exchanger. The collector design is a variation on the inverted batch heater which takes its inspiration from a number of solar designers of similar units and introduces several additional measures to take advantage of the wood heating connection and to improve the design based on operating experience.

Poitras, R.

1980-01-01T23:59:59.000Z

240

Leonard Wood and the American Empire  

E-Print Network (OSTI)

During the ten years following the Spanish American War (1898 to 1908), Major General Leonard Wood served as the primary agent of American imperialism. Wood was not only a proconsul of the new American Empire; he was a symbol of the empire and the age in which he served. He had the distinction of directing civil and military government in Cuba and the Philippines where he implemented the imperial policies given to him by the administrations of William McKinley and Theodore Roosevelt. In Cuba, he labored to rebuild a state and a civil society crippled by decades of revolutionary ferment and guided the administration's policy through the dangerous channels of Cuban politics in a way that satisfied – at least to the point of avoiding another revolution – both the Cubans and the United States. In the Philippines, Wood took control of the Moro Province and attempted to smash the tribal-religious leadership of Moro society in order to bring it under direct American rule. His personal ideology, the imperial policies he shepherded, and the guidance he provided to fellow military officers and the administrations he served in matters of colonial administration and defense shaped the American Empire and endowed it with his personal stamp.

Pruitt, James Herman

2011-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Wood and Pellet Heating Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood and Pellet Heating Basics Wood and Pellet Heating Basics Wood and Pellet Heating Basics August 16, 2013 - 3:02pm Addthis Wood-burning and pellet fuel appliances use biomass or waste resources to heat homes or buildings. Types of Wood- and Pellet-Burning Appliances The following is a brief overview of the different types of wood and pellet fuel appliances available. High-Efficiency Fireplaces and Fireplace Inserts Designed more for show, traditional open masonry fireplaces should not be considered heating devices. Traditional fireplaces draw in as much as 300 cubic feet per minute of heated room air for combustion, then send it straight up the chimney. Fireplaces also produce significant air pollution. Although some fireplace designs seek to address these issues with dedicated air supplies, glass doors, and heat recovery systems, fireplaces are still

242

Wood as a fuel. (Latest citations from the NTIS Bibliographic database). Published Search  

SciTech Connect

The bibliography contains citations concerning the availability, combustion aspects, economics, and feasibility of using wood as fuel. Topics include wood-fuel power plants, wood waste fuels, district heating systems, wood burning furnaces and appliances, and wood waste generators. (Contains a minimum of 128 citations and includes a subject term index and title list.)

Not Available

1994-05-01T23:59:59.000Z

243

Mitigation potential and cost in tropical forestry - relative role for agroforestry  

SciTech Connect

This paper summarizes studies of carbon mitigation potential (MP) and costs of forestry options in seven developing countries with a focus on the role of agroforestry. A common methodological approach known as comprehensive mitigation assessment process (COMAP) was used in each study to estimate the potential and costs between 2000 and 2030. The approach requires the projection of baseline and mitigation land-use scenarios derived from the demand for forest products and forestland for other uses such as agriculture and pasture. By using data on estimated carbon sequestration, emission avoidance, costs and benefits, the model enables one to estimate cost effectiveness indicators based on monetary benefit per t C, as well as estimates of total mitigation costs and potential when the activities are implemented at equilibrium level. The results show that about half the MP of 6.9 Gt C (an average of 223 Mt C per year) between 2000 and 2030 in the seven countries could be achieved at a negative cost, and the other half at costs not exceeding $100 per t C. Negative cost indicates that non-carbon revenue is sufficient to offset direct costs of about half of the options. The agroforestry options analyzed bear a significant proportion of the potential at medium to low cost per t C when compared to other options. The role of agroforestry in these countries varied between 6% and 21% of the MP, though the options are much more cost effective than most due to the low wage or opportunity cost of rural labor. Agroforestry options are attractive due to the large number of people and potential area currently engaged in agriculture, but they pose unique challenges for carbon and cost accounting due to the dispersed nature of agricultural activities in the tropics, as well as specific difficulties arising from requirements for monitoring, verification, leakage assessment and the establishment of credible baselines.

Makundi, Willy R.; Sathaye, Jayant A.

2004-01-01T23:59:59.000Z

244

Potential of distributed wood-based biopower systems serving basic electricity needs in rural Uganda  

E-Print Network (OSTI)

$/odt), a low capacity factor for the biopower system of 0.5 (therefore requiring installation of a larger unit, State University of New York, College of Environmental Sciences and Forestry (SUNY-ESF), One Forestry to compete with alternative sources of electricity: Cost and land use estimates assumed a rather high

Vermont, University of

245

Regeneração de Floresta Secundária Eric A. Davidson Woods...  

NLE Websites -- All DOE Office Websites (Extended Search)

299 a 309. 1 Limitaes de Nutrientes para a Regenerao de Floresta Secundria Eric A. Davidson Woods Hole Research Center, Falmouth, Massachusetts, USA Luiz A. Martinelli...

246

Water Sampling At Little Valley Area (Wood, 2002) | Open Energy...  

Open Energy Info (EERE)

Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Water Sampling At Little Valley Area (Wood, 2002) Exploration Activity Details Location...

247

Wood County Electric Coop, Inc | Open Energy Information  

Open Energy Info (EERE)

Wood County Electric Coop, Inc Place Texas Utility Id 20927 Utility Location Yes Ownership C NERC Location SPP NERC SPP Yes Activity Transmission Yes Activity Distribution Yes...

248

Wood-boring Insects of Trees and Shrubs  

E-Print Network (OSTI)

This publication explains how to identify and control wood-boring insects that invade shrubs and shade trees in Texas. 12 pages, 9 figures, 6 photographs, 1 table

Drees, Bastiaan M.; Jackman, John A.; Merchant, Michael E.

2008-06-17T23:59:59.000Z

249

Graphite/Copper Composites from Natural Wood Precursors  

Science Conference Proceedings (OSTI)

Graphite derived from natural wood precursors provides a uniquely anisotropic porous scaffold for the fabrication of graphite/copper composites. The wettability ...

250

The Viscoelastic Properties of Wood Cell Walls after Minimally ...  

Science Conference Proceedings (OSTI)

Samples were prepared on dried wood with no embedding resin within the cellular structure. Four types of analysis methods were used; the standard method, ...

251

City of Wood River, Nebraska (Utility Company) | Open Energy...  

Open Energy Info (EERE)

Nebraska (Utility Company) Jump to: navigation, search Name City of Wood River Place Nebraska Utility Id 20945 Utility Location Yes Ownership M NERC Location MRO NERC SPP Yes...

252

Wood Pulp Digetster Wall Corrosion Investigation  

DOE Green Energy (OSTI)

The modeling of the flow in a wood pulp digester is but one component of the investigation of the corrosion of digesters. This report describes the development of a Near-Wall-Model (NWM) that is intended to couple with a CFD model that determines the flow, heat, and chemical species transport and reaction within the bulk flow of a digester. Lubrication theory approximations were chosen from which to develop a model that could determine the flow conditions within a thin layer near the vessel wall using information from the interior conditions provided by a CFD calculation of the complete digester. The other conditions will be determined by coupled solutions of the wood chip, heat, and chemical species transport and chemical reactions. The NWM was to couple with a digester performance code in an iterative fashion to provide more detailed information about the conditions within the NW region. Process Simulations, Ltd (PSL) is developing the digester performance code. This more detailed (and perhaps more accurate) information from the NWM was to provide an estimate of the conditions that could aggravate the corrosion at the wall. It is intended that this combined tool (NWM-PSL) could be used to understand conditions at/near the wall in order to develop methods to reduce the corrosion. However, development and testing of the NWM flow model took longer than anticipated and the other developments (energy and species transport, chemical reactions and linking with the PSL code) were not completed. The development and testing of the NWM are described in this report. In addition, the investigation of the potential effects of a clear layer (layer reduced in concentration of wood chips) near the wall is reported in Appendix D. The existence of a clear layer was found to enhance the flow near the wall.

Giles, GE

2003-09-18T23:59:59.000Z

253

Section 7.1.3 Wood Products: Greening Federal Facilities; Second...  

NLE Websites -- All DOE Office Websites (Extended Search)

wood is being used in a building, there is an opportunity to advance good forest management by specifying certified wood products. When wood is be- ing used for framing-more...

254

How Wood Chip Size Affects Pretreatment Effectiveness of Woody Biomass for Biological Processing  

E-Print Network (OSTI)

Parameters employed for heating of wood chips employed inParameters employed for heating of wood chips employed inW.T. , 2006. Estimating heating times of wood boards, square

Tam, Jerry

2013-01-01T23:59:59.000Z

255

Wood Pellet Heating Systems: The Earthscan Expert Handbook of Planning, Design and Installation  

Science Conference Proceedings (OSTI)

Wood Pellet Heating Systems is a comprehensive handbook covering all aspects of wood pellet heating technology. The use of wood pellets as an alternative heating fuel is already well established in several countries and is becoming widespread as fossil ...

Dilwyn Jenkins

2010-04-01T23:59:59.000Z

256

My voice shall fill the woods : Lydgate, poetic authority, and the canonization of Philomela  

E-Print Network (OSTI)

My Voice Shall Fill the Woods: Lydgate, Poetic Authority,My Voice Shall Fill the Woods: Lydgate, Poetic Authority,the nightingale fills the woods with song, beautiful and

Gillespie, Mary Elizabeth

2010-01-01T23:59:59.000Z

257

Digestive enzyme activities and gastrointestinal fermentation in wood-eating catfishes  

E-Print Network (OSTI)

our data on wild-caught wood-eating catWshes appear to bein the Amazo- nian basin, and the wood-eating species likelyby reducing the particle size of wood from coarse debris to

German, Donovan P.; Bittong, Rosalie A.

2009-01-01T23:59:59.000Z

258

North Woods River: The St. Croix River in Upper Midwest History  

E-Print Network (OSTI)

Review: North Woods River: The St. Croix River in Upperand Karamanski, Theodore J. North Woods River: The St. Croixbeauty and splendor. In North Woods River, Eileen M. McMahon

Karalus, Daniel E

2011-01-01T23:59:59.000Z

259

Metagenomic and functional analysis of hindgut microbiota of a wood-feeding higher termite  

E-Print Network (OSTI)

and western branches of the Wood/Ljungdahl pathway: how the1993). 55. Wood, T. Preparation of crystalline,of hindgut microbiota of a wood-feeding higher termite Falk

Warnecke, Falk

2008-01-01T23:59:59.000Z

260

Daughters of Dissent: Women as Warriors in Sembene Ousmane's God's Bits of Wood  

E-Print Network (OSTI)

Sembene. Gods Bits of Wood. Heinemann, Soyinka, Wole. Myth,novel, God's Bits of Wood, with particular reference to theOusmane's novel, God's Bits of Wood. It is important to note

Abdurrahman, Umar

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Save the tree of life or get lost in the woods  

E-Print Network (OSTI)

of life or get lost in the woods Biology Direct 2010, 5:44of life or get lost in the woods Ruben E Valas* 1 and PhilipOtherwise one gets lost in the woods of neutral evolution.

Valas, Ruben E; Bourne, Philip E

2010-01-01T23:59:59.000Z

262

The use of a permanent magnet for water content measurements of wood chips  

E-Print Network (OSTI)

Water Content Measurements of Wood Chips * P. J. Barale, C.measures the water content of wood chips, pulp and brownwater content measurements in wood chips in a magnetic field

2001-01-01T23:59:59.000Z

263

Thermal conductivity modeling of building façade materials  

Science Conference Proceedings (OSTI)

An experimental research has been conducted to assess the thermo-physical properties of three building materials in both dry and moist state: beech wood, autoclaved aerated concrete and brick. The objectives of the paper envisage the measurement of the ... Keywords: building materials, contact temperature, determining method, finite element, numerical modeling, thermal conductivity

Monica Chereches; Nelu-Cristian Chereches; Catalin Popovici

2010-04-01T23:59:59.000Z

264

Economic feasibility study of a wood gasification-based methanol plant: A subcontract report  

DOE Green Energy (OSTI)

This report presents an economic feasibility study for a wood-gasification-based methanol plant. The objectives were to evaluate the current commercial potential of a small-scale, wood-fed methanol plant using the SERI oxygen-blown, pressurized, down-draft gasifier technology and to identify areas requiring further R and D. The gasifier gas composition and material balance were based on a computer model of the SERI gasifier since acceptable test data were not available. The estimated capital cost was based on the Nth plant constructed. Given the small size and commercial nature of most of the equipment, N was assumed to be between 5 and 10. Only large discrepancies in gasifier output would result in significant charges in capital costs. 47 figs., 55 tabs.

Not Available

1987-04-01T23:59:59.000Z

265

A Wood-Fired Gas Turbine Plant  

E-Print Network (OSTI)

This paper covers the research and development of a wood-fired gas turbine unit that is used for generating electricity. The system uses one large cyclonic combustor and a cyclone cleaning system in series to provide hot gases to drive an Allison T-56 aircraft engine (the industrial version is the 501-k). A Westinghouse 3,000-kW generator is used on the prototype facility with a Philadelphia gear system reducing the 14,000-rpm turbine output speed to the 3,600-rpm generator operating speed. Fuel is fed into the combustor by a rotary valve system. The swirling effect of the cyclone combustor ensures that residence time is adequate to completely burn all solid particles in the combustor ahead of the cyclone filter. Burning of particles on the metal walls of the cyclone filter could cause overheating and deterioration of the walls. This wood-fired gas turbine unit could provide a low cost source of power for areas where conventional methods are now prohibitive and provide a means for recovering energy from a source that now poses disposal problems.

Powell, S. H.; Hamrick, J. T.

1986-06-01T23:59:59.000Z

266

Silviculture: growing more wood on less land  

SciTech Connect

Maximizing the production of a concentrated, homogeneous wood supply virtually dictates intensively managed plantations. This management system implies: (1) improving the composite genotype of plantation trees; (2) optimizing their morphological and physiological condition prior to and at planting time; (3) improving the physiological environment of the crop at all stages of development; (4) protecting the plantation from pests and catastrophic events; and (5) modifying the shapes, dimensions, and qualities of crop trees to enhance the utility and value of harvested timber. Beneficiation of forest residuals for fiber and fuel is pushing forest industry relentlessly toward total stand utilization. Relative to the productivity of undisturbed or partially logged humid tropical forests, plantation growth rates represent four-fold to ten-fold increases in volume production. Displacement of some proportion of shifting agriculture and natural forest management systems by intensively managed plantations is desirable and biologically feasible. A key to successful tropical forest management and preservation is population stability, a condition toward which integrated wood conversion facilities supplied by a reliable plantation system can make a major contribution. There are some pressing and many esoteric reasons for conserving forest resources but pressures for utilizing and renewing these resources are immediate and unavoidable.

Gladstone, W.T.

1980-01-01T23:59:59.000Z

267

Modelling piloted ignition of wood and plastics  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer We model piloted ignition times of wood and plastics. Black-Right-Pointing-Pointer The model is applied on a packed bed. Black-Right-Pointing-Pointer When the air flow is above a critical level, no ignition can take place. - Abstract: To gain insight in the startup of an incinerator, this article deals with piloted ignition. A newly developed model is described to predict the piloted ignition times of wood, PMMA and PVC. The model is based on the lower flammability limit and the adiabatic flame temperature at this limit. The incoming radiative heat flux, sample thickness and moisture content are some of the used variables. Not only the ignition time can be calculated with the model, but also the mass flux and surface temperature at ignition. The ignition times for softwoods and PMMA are mainly under-predicted. For hardwoods and PVC the predicted ignition times agree well with experimental results. Due to a significant scatter in the experimental data the mass flux and surface temperature calculated with the model are hard to validate. The model is applied on the startup of a municipal waste incineration plant. For this process a maximum allowable primary air flow is derived. When the primary air flow is above this maximum air flow, no ignition can be obtained.

Blijderveen, Maarten van [TNO, Schoemakerstraat 97, 2628 VK Delft (Netherlands); University of Twente, Department of Thermal Engineering, Drienerlolaan 5, 7522 NB Enschede (Netherlands); Bramer, Eddy A. [University of Twente, Department of Thermal Engineering, Drienerlolaan 5, 7522 NB Enschede (Netherlands); Brem, Gerrit, E-mail: g.brem@utwente.nl [University of Twente, Department of Thermal Engineering, Drienerlolaan 5, 7522 NB Enschede (Netherlands)

2012-09-15T23:59:59.000Z

268

Trends and Market Effects of Wood Energy Policies  

E-Print Network (OSTI)

Trends and Market Effects of Wood Energy Policies Bengt Hillring SLU SWEDEN http is the main international energy source · Climate change ­ Energy production ­ CO2 · European Union different the plans to increase #12;#12;Energy Sector Waste Sector Recovered Wood Sawdust Logging Residues Forest

269

Modeling and Rendering Physically-Based Wood Combustion  

Science Conference Proceedings (OSTI)

Rendering of wood combustion has received some attention recently, but prior work has not incorporated effects of internal wood properties such as density variation (i.e. "grain") and pre-combustion processes such as drying. In this paper we present ...

Roderick M. Riensche; Robert R. Lewis

2009-11-01T23:59:59.000Z

270

NREL: News Feature - Wood-Boring Gribbles Intrigue Researchers  

NLE Websites -- All DOE Office Websites (Extended Search)

Wood-Boring Gribbles Intrigue Researchers Wood-Boring Gribbles Intrigue Researchers July 24, 2013 This is a light-enhanced close-up of a tiny crustacean's head and torso, with what looks like fluorescent-blue antennae. Three of its legs are showing. Enlarge image A gribble is a tiny wood borer that produces its own enzyme that can devastate wood efficiently. Researchers hope that by studying gribbles they can learn ways to improve the process of turning biomass into liquid fuels. Courtesy Laura Michie, University of Portsmouth, United Kingdom Tiny wood borers known colloquially as gribbles make their own enzymes and use them to eat through docks in harbor towns, earning enmity from fishermen all around the world. Now, researchers from the Energy Department's National Renewable Energy Laboratory (NREL) and elsewhere are exploring whether that curse can be

271

Steam gasification of wood in the presence of catalysts  

SciTech Connect

Catalytic steam gasification of wood, including sawdust, chipped forest slash, and mill shavings, is being investigated. Results of laboratory, process development unit (PDU), and feasibility studies illustrate attractive processes for conversion of wood to methanol and a substitute natural gas (SNG). Recent laboratory studies developed a long-lived alloy catalyst for generation of a methanol synthesis gas by steam gasification of wood. Modification of the PDU for operation at 10 atm (150 psia) is nearly complete. The modified PDU will be operated at the elevated pressure to confirm yields and design parameters used in process feasibility studies. Feasibility studies were completed on wood-to-methane (SNG) and wood-to-methanol plants with capacities of 2000 and 200 oven dried tons (1800 and 180 metric t) per day using catalytic gasification. The results showed that generation of methanol on the large scale is economically viable today while SNG generation is competitive with future prices.

Mitchell, D.H.; Mudge, L.K.; Baker, E.G.

1981-01-01T23:59:59.000Z

272

Effects of wood fuel use on plant management  

SciTech Connect

During the winter of 1979-80, about 20% of homeowners in the New England region relied on wood fuel as their primary source of heat; an additional 30% used wood heat on a supplementary basis. The demand for wood put a great strain on the New England forests. However, experts in forest management believe that with proper management and utilization, national forest growth could replace as much as four billion gpy of oil by 2023. Implications for the forests of the Upper Great Lakes region of increased use of public and private woodlands for fuel are examined. Conflicts that could arise with the tourist and recreation industry, and with wilderness preservation interests, and discussed. Wood wastes generated by timber harvesting, sawmills, and lumber manufacturing could be collected and used as fuel, thus reducing the amount of raw wood resources needed to fill the increasing demand. (6 photos)

Harris, M.; Buckmann, C.A.

1980-09-01T23:59:59.000Z

273

Performance of bolted wood connections using supplemental confining devices  

E-Print Network (OSTI)

In the aftermath of the 1994 Northridge Earthquake, extensive field investigations revealed damage in wood frame construction in the form of splitting the 2x4 or 2x6 dimension lumber sill plates along the line of anchor bolts which typically connect shear walls to the masonry or concrete foundation. This paper presents an experimental investigation on the performance of bolted wood connections at the yield and ultimate limit states during monotonic and incremental quasi-static reversed cyclic loading and suggests possible retrofit strategies for their improved seismic performance. Proposed retrofit strategies are based on providing confinement to the bolted wood member using metal reinforcing ;traps and reinforcing clamps to increase the deformation capability and energy dissipation capacity of the connection, while maintaining substantial levels of connection strength. Connection types included in the investigation are: (1) double shear wood-to-wood connections; and (2) single shear simulated sill plate-to-concrete foundation connections.

Stromatt, Rebecca Faye

1996-01-01T23:59:59.000Z

274

Biomass plants face wood supply risks Report warns giant new biomass power plants will be hugely reliant on wood chip  

E-Print Network (OSTI)

Biomass plants face wood supply risks Report warns giant new biomass power plants will be hugely's biomass energy sector could be undermined unless businesses move to resolve the supply chain issues-scale biomass plants will leave generators largely reliant on biomass from overseas such as wood chips, elephant

275

IMPORTED SOIL OR SOIL-FORMING MATERIALS  

E-Print Network (OSTI)

depending on local availability. An automated version of the soil textural classification triangle shownNeill, J. (1994). Reclaiming disturbed land for forestry. Forestry Commission Bulletin 110. HMSO, London

276

Implementing Strategies for Drying and Pressing Wood Without Emissions Controls  

DOE Green Energy (OSTI)

Drying and pressing wood for the manufacture of lumber, particleboard, oriented strand board (OSB), veneer and medium density fiberboard (MDF) release volatile organic compounds (VOCs) into the atmosphere. These emissions require control equipment that are capital-intensive and consume significant quantities of natural gas and electricity. The objective of our work was to understand the mechanisms through which volatile organic compounds are generated and released and to develop simple control strategies. Of the several strategies developed, two have been implemented for OSB manufacture over the course of this study. First, it was found that increasing final wood moisture by about 2-4 percentage points reduced the dryer emissions of hazardous air pollutants by over 70%. As wood dries, the escaping water evaporatively cools the wood. This cooling tapers off wood when the wood is nearly dry and the wood temperature rises. Thermal breakdown of the wood tissue occurs and VOCs are released. Raising the final wood moisture by only a few percentage points minimizes the temperature rise and reduces emissions. Evaporative cooling also impacts has implications for VOC release from wood fines. Flaking wood for OSB manufacture inevitable generates fines. Fines dry out rapidly because of their high surface area and evaporative cooling is lost more rapidly than for flakes. As a result, fines emit a disproportionate quantity of VOCs. Fines can be reduced in two ways: through screening of the green furnish and through reducing their generation during flaking. The second approach is preferable because it also increased wood yield. A procedure to do this by matching the sharpness angle of the flaker knife to the ambient temperature was also developed. Other findings of practical interests are as follows: Dielectric heating of wood under low-headspace conditions removes terpenes and other extractives from softwood; The monoterpene content in trees depend upon temperature and seasonal effects; Method 25A emissions from lumber drying can be modeled from a knowledge of the airflow through the kiln; A heat transfer model shows that VOCs released during hot-pressing mainly originate from the surface of the board; and Boiler ash can be used to adsorb formaldehyde from air streams.

Sujit Banerjee; Terrance Conners

2007-09-07T23:59:59.000Z

277

Chemical, ultrastructural and supramolecular analysis of tension wood in Populus tremula x alba as a model substrate for reduced recalcitrance  

SciTech Connect

Biomass is one of the most abundant potential sustainable sources for fuel and material production, however to fully realize this potential an improved understanding of lignocellulosic recalcitrance must be developed. In an effort to appreciate the underlying phenotypic, biochemical and morphological properties associated with the reduced recalcitrance observed in tension stress-induced reaction wood, we report the increased enzymatic sugar yield and corresponding chemical and ultrastructural properties of Populus tension wood. Populus tremula x alba (PTA) was grown under tension and stem segments containing three different wood types: normal wood (NW), tension wood (TW) from the elongated stem side and opposite wood (OW) from the compressed stem side were collected. A variety of analytical techniques were used to describe changes occurring as a result of the tension stress-induced formation of a gelatinous cell wall layer (G-layer). For example, gel permeation chromatography (GPC) and 13C solid-state nuclear magnetic resonance (NMR) revealed that the molecular weight and crystallinity of cellulose in TW is greater than that of cellulose acquired from NW. Whole cell ionic liquid and other solid-state NMR analysis detailed the structure of lignin and hemicellulose in the samples, detecting the presence of variations in lignin and hemicellulose sub-units, linkages and semi-quantitatively estimating the relative amounts of syringyl (S), guaiacyl (G) and p-hydroxybenzoate (PB) monolignol units. It was confirmed that TW displayed an increase in PB or H-like lignin and S to G ratio from 1.25 to 1.50 when compared to the NW sample. Scanning electron microscopy (SEM) and coherent anti-Stokes Raman scattering (CARS) were also used to evaluate the morphology and corresponding spatial distribution of the major lignocellulosic components. We found changes in a combination of cell wall properties appear to influence recalcitrance more than any single factor alone.

Foston, Marcus B [ORNL; Hubbell, Christopher A [ORNL; Samuel, Reichel [ORNL; Jung, Seung-Yong [ORNL; Ding, Shi-You [ORNL; Zeng, Yining [ORNL; Jawdy, Sara [ORNL; Sykes, Virginia R [ORNL; Tuskan, Gerald A [ORNL; Kalluri, Udaya C [ORNL; Ragauskas, Arthur J [ORNL

2011-01-01T23:59:59.000Z

278

Financing options for projects converting forestry and farm wastes to energy  

DOE Green Energy (OSTI)

A significant barrier to increased use of wastes and residues as fuel by small- and medium-sized industries is financing of projects. This document covers governmental and private sector financing options available to prospective users of wood residues and agricultural wastes for industrial applications-direct combustion, steam generation, or cogeneration. This guide contains four major sections. Section I provides brief descriptions of the type of project financing options available to industry through private sector sources. This section is not intended to provide the level of detailed information required to make a final determination of the best source of private sector financing for a particular company or organization. It does, however, present a concise review of the options available on which more detailed study can be based. Section II introduces the availability of assistance for specific types of projects from federal, state, and several municipalities. Section III presents two case studies of costs, annual savings, return on investment, and payback periods for these projects, as well as the affects of depreciation, taxes, tax credits and sale of excess power. All facts and figures were supplied by the individual companies or by their engineering consulting firms. A checklist for decisions concerning bioenergy projects, as well as addresses and contacts in regional government agency offices involved in providing financial assistance, are included in the final section.

Farley, R.C.; Parker, S.K.; Hodam, R.

1980-07-01T23:59:59.000Z

279

Homeowners energy conservation and consumption behavior: wood users and non/low wood users  

SciTech Connect

Relationships among energy expenditure, energy consumption, energy-budget share, energy managerial practices, housing, and household-membership factors for non/low wood-user and high wood-user households were examined to explain substitution of fuelwood for primary fuels. Data were from a nationwide representative sample of 1599 homeowners collected by the Department of Energy in 1982-1983 Residential Energy Conservation Survey. In three multivariate regression models, different dependent variables - energy expenditure, energy consumption, and energy budget share, were used. The same independent variables - housing factors, household energy managerial practices, and household membership factors, were used in the three models. Finally, in a fourth model, discriminant analysis with the dichotomous criterion variable of non/low or high wood users and significant variables from the multivariate regressions models were used to explain 34% of the variance. The amount of space heated, their appliance use, whether they had teenage children, and if they were single-earner households were significant explanatory variables in all four models.

Urich, J.R.

1986-01-01T23:59:59.000Z

280

Crop, forestry, and manure residue inventory: continental United States. Volume 3. West North-Central, including: Iowa, Kansas, Minnesota, Missouri, Nebraska, North Dakota, and South Dakota  

SciTech Connect

Tabulated data are compiled on the generation and utilization of crop, forestry, and manure residues. The utilization categories are defined as selling the residue for use other than as a fuel, feeding the residues to animals, use as fuel, return of the residue to the soil, and wastage. The tabulations are by state and by county within the state. (JSR)

1976-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Flash polymerization of silicone oils using gamma radiation for conserving waterlogged wood  

E-Print Network (OSTI)

A series of experiments were designed to develop a collection of irradiation parameters for polymerizing a variety of molecular weights of polymer siloxanes for the purpose of bulking and conserving waterlogged archaeological organic materials. Waterlogged wooden tongue depressors (Betula spp) were bulked with five different silicone oils of varying molecular weights, denoted as PS340, PS341, PS343, SFD-1, and an equal mix of SFD-1 and SFD-5. The lightest weight oil being PS340 and the heaviest being the SFD-I /SFD-5 mix. These bulked samples were exposed to gamma radiation emitted from a nuclear research reactor and received gamma doses ranging from 30 Gy to 228 Gy with dose rates ranging from 0.6 Gy/min to 5.1 Gy/min. Following irradiation, thin cross sections of each tongue depressor were analyzed and photographed using a photomicroscope. The results of the irradiation indicated that the heavier molecular weights of siloxanes fully bulked the wood cells. For these fully bulked samples, large radiation doses induced polymerization in the oil to such an extent the cells swelled and became extremely distorted. However, for the same fully bulked samples, small radiation doses produced little to moderate polymerization of the oil in the wood cells. For the tongue depressors bulked with the lighter weight siloxanes, low radiation doses produced very little polymerization, whereas the higher doses induced substantially more polymerization within the wood cells but not to the point of distortion. With these lighter weight siloxanes, the wood cells were not as fully bulked nor looked as natural as those cells bulked with the heavier weight oils. The best combination of molecular weight and radiation dose occurred with the samples bulked in PS343 and irradiated with gamma-rays to a dose of 150 Gy.

Gidden, Richmond Paul

1996-01-01T23:59:59.000Z

282

A model for the oxidative pyrolysis of wood  

SciTech Connect

A generalized pyrolysis model (Gpyro) is applied to simulate the oxidative pyrolysis of white pine slabs irradiated under nonflaming conditions. Conservation equations for gaseous and solid mass, energy, species, and gaseous momentum (Darcy's law approximation) inside the decomposing solid are solved to calculate profiles of temperature, mass fractions, and pressure inside the decomposing wood. The condensed phase consists of four species, and the gas that fills the voids inside the decomposing solid consists of seven species. Four heterogeneous (gas/solid) reactions and two homogeneous (gas/gas) reactions are included. Diffusion of oxygen from the ambient into the decomposing solid and its effect on local reactions occurring therein is explicitly modeled. A genetic algorithm is used to extract the required material properties from experimental data at 25 kW/m{sup 2} and 40 kW/m{sup 2} irradiance and ambient oxygen concentrations of 0%, 10.5% and 21% by volume. Optimized model calculations for mass loss rate, surface temperature, and in-depth temperatures reproduce well the experimental data, including the experimentally observed increase in temperature and mass loss rate with increasing oxygen concentration. (author)

Lautenberger, Chris; Fernandez-Pello, Carlos [Department of Mechanical Engineering, University of California, Berkeley, Berkeley, CA 94720 (United States)

2009-08-15T23:59:59.000Z

283

Prioritizing wood energy crop feedstock qualities for biofuel systems improvement  

SciTech Connect

Knowledge engineering or expert systems is needed in biofuel systems to adequately prioritize wood energy crop traits on which research and development should focus. Objectives at the various stages of the total biofuel process are clarifying the demands that will be placed on feedstock qualities. These objectives are forming more clearly from developments in the growing, handling, and conversion of wood under operational and regulatory circumstances. A process for systematic prioritization of wood qualities for possible improvement is presented in the content of the entire biofuel process.

Ranney, J.W.

1991-01-01T23:59:59.000Z

284

Prioritizing wood energy crop feedstock qualities for biofuel systems improvement  

SciTech Connect

Knowledge engineering or expert systems is needed in biofuel systems to adequately prioritize wood energy crop traits on which research and development should focus. Objectives at the various stages of the total biofuel process are clarifying the demands that will be placed on feedstock qualities. These objectives are forming more clearly from developments in the growing, handling, and conversion of wood under operational and regulatory circumstances. A process for systematic prioritization of wood qualities for possible improvement is presented in the content of the entire biofuel process.

Ranney, J.W.

1991-12-31T23:59:59.000Z

285

Wood-Polymer composites obtained by gamma irradiation  

Science Conference Proceedings (OSTI)

In this work we impregnate three Peruvian woods (Calycophy spruceanum Be, Aniba amazonica Meiz and Hura crepitans L) with styrene-polyester resin and methyl methacrylate. The polymerization of the system was promoted by gamma radiation and the experimental optimal condition was obtained with styrene-polyester 1:1 and 15 kGy. The obtained composites show reduced water absorption and better mechanical properties compared to the original wood. The structure of the wood-polymer composites was studied by light microscopy. Water absorption and hardness were also obtained.

Gago, J. [Instituto Peruano de Energia Nuclear, Av. Canada 1470 Lima 41 (Peru); Lopez, A.; Rodriguez, J. [Instituto Peruano de Energia Nuclear, Av. Canada 1470 Lima 41 (Peru); Facultad de Ciencias, Universidad Nacional de Ingenieria, Av. Tupac Amaru 210, Lima 25 (Peru); Santiago, J. [Instituto Peruano de Energia Nuclear, Av. Canada 1470 Lima 41 (Peru); Facultad de Quimica e Ing. Quimica, Universidad Nacional Mayor de San Marcos, Lima 1 (Peru); Acevedo, M. [Facultad de Ciencias Forestales, Universidad Nacional Agraria la Molina, Lima 12 (Peru)

2007-10-26T23:59:59.000Z

286

Improved Process control of wood waste fired boilers  

DOE Green Energy (OSTI)

This project's principal aim was the conceptual and feasibility stage development of improved process control methods for wood-waste-fired water-tube boilers operating in industrial manufacturing applications (primarily pulp and paper). The specific objectives put forth in the original project proposal were as follows: (1) fully characterize the wood-waste boiler control inter-relationships and constraints through data collection and analysis; (2) design an improved control architecture; (3) develop and test an appropriate control and optimization algorithm; and (4) develop and test a procedure for reproducing the approach and deriving the benefits on similar pulp and paper wood-waste boilers. Detailed tasks were developed supporting these objectives.

Process Control Solutions, Inc.

2004-01-30T23:59:59.000Z

287

An economical and market analysis of Canadian wood pellets.  

Science Conference Proceedings (OSTI)

This study systematically examined the current and future wood pellet market, estimated the cost of Canadian torrefied pellets, and compared the torrefied pellets with the conventional pellets based on literature and industrial data. The results showed that the wood pellet industry has been gaining significant momentum due to the European bioenergy incentives and the rising oil and natural gas prices. With the new bioenergy incentives in USA, the future pellets market may shift to North America, and Canada can potentially become the largest pellet production centre, supported by the abundant wood residues and mountain pine beetle (MPB) infested trees.

Peng, J. [University of British Columbia, Vancouver

2010-08-01T23:59:59.000Z

288

Physical and mechanical properties of mixed comrind and hardwood  

E-Print Network (OSTI)

Forestry Univ., Harbin, China (guangpingh@hotmail.com); Professor, School of Renewable Natural Resources Institute of Wood Industry, Chinese Academy of Forestry, Beijing, China (duanchitosan

289

IS DENSIFIED BIOMASS FUEL FROM AGRO-FORESTRY WASTE A SUSTAINABLE ENERGY OPTION?.  

E-Print Network (OSTI)

??Raw biomass material is bulky, high in void fraction, and very low in transportation efficiency. Furthermore, biomass dissipates quickly in harsh environments of high heat… (more)

Linnig, William A., III

2012-01-01T23:59:59.000Z

290

Weathering of Roofing Materials-An Overview  

Science Conference Proceedings (OSTI)

An overview of several aspects of the weathering of roofing materials is presented. Degradation of materials initiated by ultraviolet radiation is discussed for plastics used in roofing, as well as wood and asphalt. Elevated temperatures accelerate many deleterious chemical reactions and hasten diffusion of material components. Effects of moisture include decay of wood, acceleration of corrosion of metals, staining of clay, and freeze-thaw damage. Soiling of roofing materials causes objectionable stains and reduces the solar reflectance of reflective materials. (Soiling of non-reflective materials can also increase solar reflectance.) Soiling can be attributed to biological growth (e.g., cyanobacteria, fungi, algae), deposits of organic and mineral particles, and to the accumulation of flyash, hydrocarbons and soot from combustion.

Berdahl, Paul; Akbari, Hashem; Levinson, Ronnen; Miller, William A.

2006-03-30T23:59:59.000Z

291

Method for lowering the VOCS emitted during drying of wood products  

DOE Patents (OSTI)

The present invention is directed to a method for removal of VOCs from wood products prior to drying the wood products. The method of the invention includes the steps of providing a chamber having an opening for receiving wood and loading the chamber with green wood. The wood is loaded to an extent sufficient to provide a limited headspace in the chamber. The chamber is then closed and the wood is heated in the chamber for a time and at a temperature sufficient to saturate the headspace with moisture and to substantially transfer VOCs from the wood product to the moisture in the headspace.

Banerjee, Sujit (1832 Jacksons Creek Point, Marietta, GA 30068); Boerner, James Robert (154 Junedale Rd., Cincinnati, OH 45218); Su, Wei (2262 Orleans Ave., Marietta, GA 30062)

2000-01-01T23:59:59.000Z

292

Biomimetic soy protein nanocomposites with calcium carbonate crystalline arrays for use as wood adhesive  

E-Print Network (OSTI)

a a College of Forestry, South China Agricultural University, Guangzhou 510642, China b School of Renewable a b s t r a c t Despite the biodegradability, non-toxicity, and renewability, commercially available

293

Contribution of organic carbon to wood smoke particulate matter absorption  

NLE Websites -- All DOE Office Websites (Extended Search)

Contribution of organic carbon to wood smoke particulate matter absorption Contribution of organic carbon to wood smoke particulate matter absorption of solar radiation Title Contribution of organic carbon to wood smoke particulate matter absorption of solar radiation Publication Type Journal Article Year of Publication 2012 Authors Kirchstetter, Thomas W., and Tracy L. Thatcher Journal Atmospheric Chemistry and Physics Volume 12 Pagination 6067-6072 Abstract A spectroscopic analysis of 115 wintertime partic- ulate matter samples collected in rural California shows that wood smoke absorbs solar radiation with a strong spectral se- lectivity. This is consistent with prior work that has demon- strated that organic carbon (OC), in addition to black car- bon (BC), appreciably absorbs solar radiation in the visible and ultraviolet spectral regions. We apportion light absorp-

294

International WoodFuels LLC | Open Energy Information  

Open Energy Info (EERE)

WoodFuels LLC WoodFuels LLC Jump to: navigation, search Name International WoodFuels LLC Place Portland, Maine Zip 4101 Product Maine-based pellet producer and installer of commercial wood pellet heating systems. Coordinates 45.511795°, -122.675629° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.511795,"lon":-122.675629,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

295

Stanford - Woods Institute for the Environment | Open Energy Information  

Open Energy Info (EERE)

Stanford - Woods Institute for the Environment Stanford - Woods Institute for the Environment Jump to: navigation, search Logo: Stanford- Woods Institute for the Environment Name Stanford- Woods Institute for the Environment Address 473 Via Ortega Place Stanford, California Zip 94305 Region Bay Area Coordinates 37.427774°, -122.175672° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.427774,"lon":-122.175672,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

296

Residential Wood Heating Fuel Exemption (New York) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood Heating Fuel Exemption (New York) Wood Heating Fuel Exemption (New York) Residential Wood Heating Fuel Exemption (New York) < Back Eligibility Multi-Family Residential Residential Savings Category Bioenergy Maximum Rebate None Program Info State New York Program Type Sales Tax Incentive Rebate Amount 100% exemption Provider New York State Department of Taxation and Finance New York exempts retail sales of wood used for residential heating purposes from the state sales tax. The law also permits local governments (municipalities and counties) to grant an exemption from local sales taxes. If a city with a population of 1 million or more chooses to grant the local exemption, it must enact a specific resolution that appears in the state law. Local sales tax rates in New York range from 1.5% to more than 4% in

297

Qualifying Wood Stove Deduction (Idaho) | Open Energy Information  

Open Energy Info (EERE)

Share this page on Facebook icon Twitter icon Qualifying Wood Stove Deduction (Idaho) This is the approved revision of this page, as well as being the most recent. Jump...

298

John H. Wood Gary R. Long David F. Morehouse Energy ...  

U.S. Energy Information Administration (EIA)

Long-Term World Oil Supply Scenarios The Future Is Neither as Bleak or Rosy as Some Assert John H. Wood Gary R. Long David F. Morehouse Energy Information Administration

299

Test evaluation of a laminated wood wind turbine blade concept  

SciTech Connect

Because of the high stiffness and fatigue strength of wood (as compared to density) along with the low cost manufacturing techniques available, a laminated wood wind turbine blade application has been studied. This report presents the results of the testing performed on elements of the wood blade-to-hub transition section which uses steel studs cast into a laminated wood spar with a filled epoxy. Individual stud samples were tested for both ultimate load carrying capability and fatigue strength. A one-time pull-out load of 78,000 lb was achieved for a 15 in. long stud with a diameter of 1 in. Tension-tension fatigue indicated that peak loads on the order of 40% of ultimate could be maintained as an endurance limit (mean load = 20,000 lb, cyclic load = +-15,000 lb). Following the individual stud testing, a full-scale inboard blade section (20 ft in length) was tested.

Faddoul, J.R.

1981-05-01T23:59:59.000Z

300

DOE Joint Genome Institute: Rot's Unique Wood Degrading Machinery...  

NLE Websites -- All DOE Office Websites (Extended Search)

February 5, 2009 Rot's Unique Wood Degrading Machinery to be Harnessed for Better Biofuels Production WALNUT CREEK, CA-An international team led by scientists from the U.S....

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Wood Products Marketing And Value-Added Opportunities  

E-Print Network (OSTI)

Opportunities -MDF- Market Opportunities -MDF- The first MDF plant started up four years ago and now there are 3 the substrate of choice for exotic wood veneer layup. Pressing veneer on MDF will give the most defect

302

Signatures of surface bundles and Milnor Wood inequalities  

E-Print Network (OSTI)

Let E be a surface bundle over a surface. We use a variant of the Milnor Wood inequality to show that $|3\\sigma(E)|\\leq \\chi(E)$.

Hamenstaedt, Ursula

2012-01-01T23:59:59.000Z

303

Development and demonstration of a wood-fired gas turbine system  

DOE Green Energy (OSTI)

The objectives of the test program were to obtain some preliminary information regarding the nature of particulate and vapor phase alkali compounds produced and to assess any deleterious impact they might have on materials of construction. Power Generating Incorporated (PGI) is developing a wood-fired gas turbine system for specialized cogeneration applications. The system is based on a patented pressurized combustor designed and tested by PGI in conjunction with McConnell Industries. The other components of the system are fuel receiving, preparation, storage and feeding system, gas clean-up equipment, and a gas turbine generator.

Smith, V.; Selzer, B.; Sethi, V.

1993-08-01T23:59:59.000Z

304

Methanol synthesis gas from catalytic steam reforming of wood  

DOE Green Energy (OSTI)

Laboratory studies were successful in developing catalyst systems and operating conditions for generation of a methanol synthesis gas, a mixture of hydrogen, carbon monoxide and carbon dioxide. Some methane remained in the gas mixture. Wood was reacted with steam at a steam-to-wood weight ratio of about 0.9 and a temperature of 750/sup 0/C (1380/sup 0/F) in the presence of several catalysts. Results are presented for two different catalyst systems.

Mudge, L.K.; Mitchell, D.H.; Robertus, R.J.; Weber, S.L.; Sealock, L.J. Jr.

1981-01-01T23:59:59.000Z

305

The adoption of e-commerce for wood enterprises  

Science Conference Proceedings (OSTI)

Lately, the internet has become a major means in electronic commerce (e-commerce), as it offers various advantages and benefits. In Greece, there are many Small- and Medium-sized Enterprises (SMEs) in the context of the timber ... Keywords: Greece, ICT adoption, PROMETHEE II method, SMEs, e-commerce, electronic commerce, multi-criteria analysis, small and medium-sized enterprises, timber trade, web content, website ranking, wood processing, wood products

Z. S. Andreopoulou; T. Koutroumanidis; B. Manos

2009-04-01T23:59:59.000Z

306

Enviva Materials LLC | Open Energy Information  

Open Energy Info (EERE)

Enviva Materials LLC Enviva Materials LLC Jump to: navigation, search Name Enviva Materials LLC Place Richmond, Virginia Zip 23219 Sector Biomass Product Recovering of agricultural, forestry and industrial byproducts in order to supply the biomass power industry. Coordinates 37.5407°, -77.433654° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.5407,"lon":-77.433654,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

307

Extracellular oxidative metabolism of wood decay fungi  

DOE Green Energy (OSTI)

Substantial progress has been made toward understanding the fundamental physiology and genetics of wood decay fungi, microbes that are capable of degrading all major components of plant cell walls. Efficient utilization of lignocellulosic biomass has been hampered in part by limitations in our understanding of enzymatic mechanisms of plant cell wall degradation. This is particularly true of woody substrates where accessibility and high lignin content substantially complicate enzymatic 'deconstruction'. The interdisciplinary research has illuminated enzymatic mechanisms essential for the conversion of lignocellulosics to simple carbohydrates and other small molecular weight products. Progress was in large part dependent on substantial collaborations with the Department of Energy's Joint Genome Institute (JGI) in Walnut Creek and Los Alamos, as well as the Catholic University, Santiago, Chile, the Royal Institute of Technology, Stockholm, the University of Minnesota, St. Paul, and colleagues at the University of Wisconsin and the Forest Products Laboratory. Early accomplishments focused on the development of experimental tools (2, 7, 22, 24-26, 32) and characterization of individual genes and enzymes (1, 3-5, 8, 9, 11, 14, 15, 17, 18, 23, 27, 33). In 2004, the genome of the most intensively studied lignin-degrading fungus, Phanerochaete chrysosporium, was published (21). This milestone lead to additional progress on this important model system (6, 10, 12, 13, 16, 28-31) and was further complemented by genome analysis of other important cellulose-degrading fungi (19, 20). These accomplishments have been highly cited and have paved the way for whole new research areas.

Daniel Cullen

2010-04-21T23:59:59.000Z

308

Potential use of wood and agriculture wastes as steam generator fuel for thermal enhanced oil recovery. Final report  

DOE Green Energy (OSTI)

Enhanced oil recovery by steam injection methods produces over 200,000 barrels per day of crude oil in California. A sizeable portion of the produced crude, up to 40% for some projects, may be burned to generate steam for injection into the reservoir. The purpose of this study is to evaluate the potential to use wood and agriculture wastes to replace crude oil as steam generator fuel. The Bakersfield area of California's San Joaquin Valley is the focus for this paper. Production from thermal EOR methods centers around Bakersfield and agriculture and wood wastes are available from the San Joaquin Valley and the nearby Sierra Nevada mountains. This paper documents the production of waste materials by county, estimated energy value of each material, and estimated transportation cost for each material. Both agriculture and wood wastes were found to be available in sizeable quantities and could become attractive steam generation fuels. However, some qualifications need to be made on the use of these materials. Transportation costs will probably limit the range of shipping these materials to perhaps 50 to 100 miles. Availability is subject to competition from existing and developing uses of these materials, such as energy sources in their immediate production area. Existing steam generators probably cannot be retrofitted to burn these materials. Fluidized bed combustion, or low Btu gasification, may be a good technology for utilization. FBC or FBG could accept a variety of waste materials. This will be important because the amount of any single waste may not be large enough to support the energy requirements of a good size thermal f a good size thermal EOR operation.

Kosstrin, H.M.; McDonald, R.K.

1979-01-01T23:59:59.000Z

309

High-Quality Draft Genome Sequence of the Opitutaceae Bacterium Strain TAV1, a Symbiont of the Wood-Feeding Termite Reticulitermes flavipes  

Science Conference Proceedings (OSTI)

Microbial communities in the termite hindgut are essential for degrading plant material. We present the high-quality draft genome sequence of the Opitutaceae bacterium strain TAV1, the first member of the phylum Verrucomicrobia to be isolated from wood-feeding termites. The genomic analysis reveals genes coding for lignocellulosic degradation and nitrogen fixation.

Isanapong, Jantiya [University of Texas, Arlington; Goodwin, Lynne A. [Los Alamos National Laboratory (LANL); Bruce, David [Los Alamos National Laboratory (LANL); Chen, Amy [U.S. Department of Energy, Joint Genome Institute; Detter, J. Chris [U.S. Department of Energy, Joint Genome Institute; Han, James [U.S. Department of Energy, Joint Genome Institute; Han, Cliff [Los Alamos National Laboratory (LANL); Held, Brittany [Los Alamos National Laboratory (LANL); Huntemann, Marcel [U.S. Department of Energy, Joint Genome Institute; Ivanova, N [U.S. Department of Energy, Joint Genome Institute; Land, Miriam L [ORNL; Mavromatis, K [U.S. Department of Energy, Joint Genome Institute; Nolan, Matt [U.S. Department of Energy, Joint Genome Institute; Pati, Amrita [U.S. Department of Energy, Joint Genome Institute; Pennacchio, Len [U.S. Department of Energy, Joint Genome Institute; Pitluck, Sam [U.S. Department of Energy, Joint Genome Institute; Szeto, Ernest [U.S. Department of Energy, Joint Genome Institute; Tapia, Roxanne [Los Alamos National Laboratory (LANL); Woyke, Tanja [U.S. Department of Energy, Joint Genome Institute; Rodrigues, Jorge L.M. [University of Texas, Arlington

2012-01-01T23:59:59.000Z

310

Moisture Distribution and Flow During Drying of Wood and Fiber  

DOE Green Energy (OSTI)

New understanding, theories, and techniques for moisture flow and distribution were developed in this research on wood and wood fiber. Improved understanding of the mechanisms of flake drying has been provided. Observations of flake drying and drying rate curves revealed that rate of moisture loss consisted of two falling rate periods and no constant rate drying period was observed. Convective heat transfer controls the first period, and bound water diffusion controls the second period. Influence of lower drying temperatures on bending properties of wood flakes was investigated. Drying temperature was found to have a significant influence on bending stiffness and strength. A worksheet for calculation of the energy required to dry a single strandboard flake was developed but has not been tested in an industrial setting yet. A more complete understanding of anisotropic transverse shrinkage of wood is proposed based on test results and statistical analysis. A simplified mod el of a wood cell's cross-section was drawn for calculating differential transverse shrinkage. The model utilizes cell wall thickness and microfibrillar packing density and orientation. In spite of some phenomena of cell wall structure not yet understood completely, the results might explain anisotropic transverse shrinkage to a major extent. Boundary layer theory was found useful for evaluating external moisture resistance during drying. Simulated moisture gradients were quire comparable to the actual gradients in dried wood. A mathematical procedure for determining diffusion and surface emission coefficients was also developed. Thermal conductivity models of wood derived from its anatomical structure were created and tested against experimental values. Model estimations provide insights into changes in heat transfer parameters during drying. Two new techniques for measuring moisture gradients created in wood during drying were developed. A new technique that utilizes optical properties of cobalt chloride was developed for nondestructive determination of surface moisture content. Fundamental new understanding of drying characteristics in wood and fiber has been provided that can be used by researchers to improve drying of wood and fiber. The three techniques for measuring moisture content and gradients provided in this study are efficient, practical, and economical - easy to apply by industry and researchers. An energy consumption worksheet is provided as a first step toward reducing energy consumed during drying of lumber and strandboard flakes. However, it will need additional verification and testing.

Zink-Sharp, Audrey; Hanna, Robert B.

2001-12-28T23:59:59.000Z

311

Contesting Governance in the Global Marketplace: A Sociological Assessment of British Efforts to Build New Markets for NGO-Certified Sustainable Wood Products  

E-Print Network (OSTI)

Towards Environmentally Sound Wood Products In the Britishof the Earth. 1995. “The Good Wood Guide. ” Friends of theRamachandra. 1990. The Unquiet Woods: Ecological Change and

McNichol, Jason

2000-01-01T23:59:59.000Z

312

Final Report: Development of Renewable Microbial Polyesters for Cost Effective and Energy- Efficient Wood-Plastic Composites  

SciTech Connect

In this project, we proposed to produce wood fiber reinforced thermoplastic composites (WFRTCs) using microbial thermoplastic polyesters in place of petroleum-derived plastic. WFRTCs are a rapidly growing product area, averaging a 38% growth rate since 1997. Their production is dependent on substantial quantities of petroleum based thermoplastics, increasing their overall energy costs by over 230% when compared to traditional Engineered Wood Products (EWP). Utilizing bio-based thermoplastics for these materials can reduce our dependence on foreign petroleum. We have demonstrated that biopolymers (polyhydroxyalkanoates, PHA) can be successfully produced from wood pulping waste streams and that viable wood fiber reinforced thermoplastic composite products can be produced from these materials. The results show that microbial polyester (PHB in this study) can be extruded together with wastewater-derived cell mass and wood flour into deck products having performance properties comparable to existing commercial HDPE/WF composite products. This study has thus proven the underlying concept that the microbial polyesters produced from waste effluents can be used to make cost-effective and energy-efficient wood-plastic composites. The cost of purified microbial polyesters is about 5-20 times that of HDPE depending on the cost of crude oil, due to high purification (40%), carbon substrate (40%) and sterilized fermentation (20%) costs for the PHB. Hence, the ability to produce competitive and functional composites with unpurified PHA-biomass mixtures from waste carbon sources in unsterile systems—without cell debris removal—is a significant step forward in producing competitive value-added structural composites from forest products residuals using a biorefinery approach. As demonstrated in the energy and waste analysis for the project, significant energy savings and waste reductions can also be realized using this approach. We recommend that the next step for development of useful products using this technology is to scale the technology from the 700-L pilot reactor to a small-scale production facility, with dedicated operation staff and engineering controls. In addition, we recommend that a market study be conducted as well as further product development for construction products that will utilize the unique properties of this bio-based material.

David N. Thompson, Robert W. Emerick, Alfred B. England, James P. Flanders, Frank J. Loge, Katherine A. Wiedeman, Michael P. Wolcott

2010-03-31T23:59:59.000Z

313

A distributed approach to accounting for carbon in wood products  

SciTech Connect

With an evolving political environment of commitments to limit emissions of greenhouse gases, and of markets to trade in emissions permits, there is growing scientific, political, and economic need to accurately evaluate carbon (C) stocks and flows especially those related to human activities. One component of the global carbon cycle that has been contentious is the stock of carbon that is physically held in harvested wood products. The carbon stored in wood products has been sometimes overlooked, but the amount of carbon contained in wood products is not trivial, it is increasing with time, and it is significant to some Parties. This paper is concerned with accurate treatment of harvested wood products in inventories of CO2 emissions to the atmosphere. The methodologies outlined demonstrate a flexible way to expand current methods beyond the assumption of a simple, first-order decay to include the use of more accurate and detailed data while retaining the simplicity of simple formulas. The paper demonstrates that a more accurate representation of decay time can have significant economic implications in a system where emissions are taxed or emissions permits are traded. The method can be easily applied using only data on annual production of wood products and two parameters to characterize their expected lifetime. These methods are not specific to wood products but can be applied to long-lived, carbon-containing products from sources other than wood, e.g. long-lived petrochemical products. A single unifying approach that is both simple and flexible has the potential to be both more accurate in its results, more efficient in its implementation, and economically important to some Parties.

Marland, Eric [Appalachian State University; Stellar, Kirk [Appalachian State University; Marland, Gregg [ORNL

2010-01-01T23:59:59.000Z

314

Carbonized material adsorbents for the removal of mercury from aqueous solutions  

SciTech Connect

Although wood has essentially been excluded as a starting material for the production of granular activated carbon because of the poor strength and friability of the products, powdered wood based activated carbons are still being used in water treatment and other liquid phase applications. However, the capability of powdered wood-based charcoal which in itself porous has not been fully known. Few studies have been conducted in harnessing its potential for adsorption purposes especially in water treatment. This study was conducted to investigate the possibility of using wood based carbonized materials from Sugi (Cryptomeria japonica D. Don) as adsorption materials in aqueous solutions of heavy metals like mercury, zinc, lead, cadmium and arsenic. However, of all the heavy metals investigated, mercury is considered to be the most toxic so this paper describes only the adsorption ability of the carbonized materials in adsorbing this metal from aqueous solutions of different concentrations.

Ishihara, S.; Pulido, L.L. [Kyoto Univ. (Japan); Kajimoto, T. [Wakayama Industrial Technology Center (Japan)

1996-12-31T23:59:59.000Z

315

Stereological techniques for synthesizing solid textures from images of aggregate materials  

E-Print Network (OSTI)

When creating photorealistic digital scenes, textures are commonly used to depict complex variation in surface appearance. For materials that have spatial variation in three dimensions, such as wood or marble, solid textures ...

Jagnow, Robert Carl, 1976-

2005-01-01T23:59:59.000Z

316

Metagenome of an Anaerobic Microbial Community Decomposing Poplar Wood Chips  

DOE Green Energy (OSTI)

This study describes the composition and metabolic potential of a lignocellulosic biomass degrading community that decays poplar wood chips under anaerobic conditions. We examined the community that developed on poplar biomass in a non-aerated bioreactor over the course of a year, with no microbial inoculation other than the naturally occurring organisms on the woody material. The composition of this community contrasts in important ways with biomass-degrading communities associated with higher organisms, which have evolved over millions of years into a symbiotic relationship. Both mammalian and insect hosts provide partial size reduction, chemical treatments (low or high pH environments), and complex enzymatic 'secretomes' that improve microbial access to cell wall polymers. We hypothesized that in order to efficiently degrade coarse untreated biomass, a spontaneously assembled free-living community must both employ alternative strategies, such as enzymatic lignin depolymerization, for accessing hemicellulose and cellulose and have a much broader metabolic potential than host-associated communities. This would suggest that such a community would make a valuable resource for finding new catalytic functions involved in biomass decomposition and gaining new insight into the poorly understood process of anaerobic lignin depolymerization. Therefore, in addition to determining the major players in this community, our work specifically aimed at identifying functions potentially involved in the depolymerization of cellulose, hemicelluloses, and lignin, and to assign specific roles to the prevalent community members in the collaborative process of biomass decomposition. A bacterium similar to Magnetospirillum was identified among the dominant community members, which could play a key role in the anaerobic breakdown of aromatic compounds. We suggest that these compounds are released from the lignin fraction in poplar hardwood during the decay process, which would point to lignin-modification or depolymerization under anaerobic conditions.

van der Lelie, D.; Taghavi, S.; McCorkle, S. M.; Li, L. L.; Malfatti, S. A.; Monteleone, D.; Donohoe, B. S.; Ding, S. Y.; Adney, W. S.; Himmel, M. E.; Tringe, S. G.

2012-05-01T23:59:59.000Z

317

Decision-maker's guide to wood fuel for small industrial energy users. Final report. [Includes glossary  

DOE Green Energy (OSTI)

The technology and economics of various wood energy systems available to the small industrial and commercial energy user are considered. This book is designed to help a plant manager, engineer, or others in a decision-making role to become more familiar with wood fuel systems and make informed decisions about switching to wood as a fuel. The following subjects are discussed: wood combustion, pelletized wood, fuel storage, fuel handling and preparation, combustion equipment, retrofitting fossil-fueled boilers, cogeneration, pollution abatement, and economic considerations of wood fuel use. (MHR)

Levi, M. P.; O'Grady, M. J.

1980-02-01T23:59:59.000Z

318

Cofiring Wood and Coal to Stoker Boilers in Pittsburgh  

DOE Green Energy (OSTI)

The prime objective of the University of Pittsburgh's overall wood/coal cofiring program is the successful introduction of commercial cofiring of urban wood wastes into the stoker boilers of western Pennsylvania. Central to this objective is the demonstration test at the Pittsburgh Brewing Company. In this test the project team is working to show that two commercially-available clean wood wastes - tub-ground pallet waste and chipped clearance wood - can be included in the fuel fed daily to an industrial stoker boiler. Irrespective of its economic outcome, the technical success of the demonstration at the brewery will allow the local air quality regulation agency to permit a parametric test at the Bellefield Boiler Plant. The objective of this test is to obtain comprehensive data on all key parameters of this operational boiler while firing wood with coal. The data would then be used for thorough generic technical and economic analyses. The technical analysis would be added to the open literature for the general planning and operational guidance for boiler owners and operators. The economic analysis would gage the potential for providing this stoker fuel commercially in an urban setting and for purchasing it regularly for combustion in an urban stoker boiler.

Cobb, J.T., Jr.; Elder, W.W.

1997-07-01T23:59:59.000Z

319

Expanding the Role of "Land Use, Land Use Change and Forestry" Projects and the Carbon Market in Addressing Global Climate Change  

Science Conference Proceedings (OSTI)

While the Land Use, Land Use Change and Forestry (LULUCF) sector is highly significant in any consideration of global climate change, the fact remains that the scale of LULUCF market activity currently is very small, particularly compared with its overall potential for carbon sequestration and importance as both a source and sink of carbon emissions. The underlying problem seems to be finding a workable policy framework. A flexible market-based policy at both international and domestic levels will score ...

2005-12-19T23:59:59.000Z

320

The evolution and ecology of interspecific territoriality: Studies of Anolis lizards and North American wood-warblers  

E-Print Network (OSTI)

and E. Bermingham. 2002. What is a wood-warbler? Molecularmultilocus phylogeny for the wood-warblers and a revisedplayback experiments with wood warblers. Ecology 82:207-218.

Losin, Neil

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

ENERGY BUDGETS AND MASONRY HOUSES: A PRELIMINARY ANALYSIS OF THE COMPARATIVE ENERGY PERFORMANCE OF MASONRY AND WOOD-FRAME HOUSES  

E-Print Network (OSTI)

ENERGY PERFORMANCE OF MASONRY AND WOOD-FRAME HOUSES David B.PERFORMANCE OF MASONRY AND WOOD-FRAME HOUSES David B. Goldsfor those studies used wood- frame construction, The energy

Goldstein, David B.

2012-01-01T23:59:59.000Z

322

Understanding wood-pool dynamics using long-term monitoring data from the Gualala River Watershed: What can we learn?  

E-Print Network (OSTI)

and D. R. Montgomery. 2003. Wood in river rehabilitation andPatterns and process of wood debris accumulation in theand S. V. Gregory. 2002. Large wood and fluvial processes.

Church, Tamara

2012-01-01T23:59:59.000Z

323

Linda Sargent Wood. A More Perfect Union: Holistic Worldviews and the Transformation of American Culture after World War II.  

E-Print Network (OSTI)

23 No. 1 Linda Sargent Wood. A More Perfect Union: HolisticCold War era, Linda Sargent Wood argues that the equallyWorld War II period. For Wood, this cultural perspective

Promnitz, Sarah

2012-01-01T23:59:59.000Z

324

I think that I shall never see {hor_ellipsis} a lovely forestry policy: Land use programs for conservation of forests  

Science Conference Proceedings (OSTI)

Forestry programs are frequently invoked as having potential for mitigation of greenhouse gas emissions. Most studies have attempted to quantify the potential impact of forest programs on carbon uptake and the potential costs of such programs. In this paper, we will attempt instead to focus on the institutional issues of the implementation of forestry programs for carbon sequestration. In particular, we explore the challenges for implementing forest programs that are: of increasing technological complexity; and in settings that depart significantly from the idealized conditions of economic models. We start in Section 1 by examining a suite of instruments that are commonly employed to implement a given policy. Section 2 examines a relatively simple case -- a tree-planting program in the US -- and demonstrates that there are significant difficulties involved in implementing a carbon sequestration program, even in a well-developed market economy. Section 3 focuses on other technologies in the US and why the choice of policy instruments and program design is more difficult than for the simple tree-planting case. Section 4 considers implementation of forestry policies in other countries where the economies may bear less resemblance to the ideal market economy than the US. In those settings, the choice of policy instruments may be very sensitive to non-market considerations that are often missed in conventional policy and cost analysis.

Rayner, S.F.; Richards, K.R.

1994-01-01T23:59:59.000Z

325

Environmental and economic evaluation of energy recovery from agricultural and forestry residues  

DOE Green Energy (OSTI)

Four conversion methods and five residues are examined in this report, which describes six model systems: hydrolysis of corn residues, pyrolysis of corn residues, combustion of cotton-ginning residues, pyrolysis of wheat residues, fermentation of molasses, and combustion of pulp and papermill wastes. Estimates of material and energy flows for those systems are given per 10/sup 12/ Btu of recovered energy. Regional effects are incorporated by addressing the regionalized production of the residues. A national scope cannot be provided for every residue considered because of the biological and physical constraints of crop production. Thus, regionalization of the model systems to the primary production region for the crop from which the residue is obtained has been undertaken. The associated environmental consequences of residue utilization are then assessed for the production region. In addition, the environmental impacts of operating the model systems are examined by quantifying the residuals generated and the land, water, and material requirements per 10/sup 12/ Btu of energy generated. On the basis of estimates found in the literature, capital, operating, and maintenance cost estimates are given for the model systems. These data are also computed on the basis of 10/sup 12/ Btu of energy recovered. The cost, residual, material, land, and water data were then organized into a format acceptable for input into the SEAS data management program. The study indicates that the most serious environmental impacts arise from residue removal rather than from conversion.

None

1980-09-01T23:59:59.000Z

326

Dover Textiles - A Case History on Retrofitting Factories with a Boiler System Fueled on Coal, Wood and Waste  

E-Print Network (OSTI)

The shortage of affordable gas and oil boiler fuels and the recent Iran/Iraq war underscores the urgent need for the American industrial system to convert to domestically controlled fuels and particularly coal, wood, and waste. More talk than action has been present. However, Dover Textiles, Shelby, North Carolina, is a major textile concern which has aggressively addressed the high cost and vulnerability of oil, as well as the increasing cost of natural gas, for their boiler system by purchasing a coal, wood, and waste fired boiler system to serve two plants. This case history will document payback periods of less than three years; return on investments of 20% plus; benefits of North Carolina and federal investment tax credits; EPA considerations, which in this case required no additional capital investment; fuel supply; material handling; ash removal; and other design considerations.

Pincelli, R. D.

1981-01-01T23:59:59.000Z

327

Hancock-Wood Electric Coop Inc | Open Energy Information  

Open Energy Info (EERE)

Hancock-Wood Electric Coop Inc Hancock-Wood Electric Coop Inc Jump to: navigation, search Name Hancock-Wood Electric Coop Inc Place Ohio Utility Id 8034 Utility Location Yes Ownership C NERC Location RFC NERC RFC Yes RTO PJM Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Farm Service-R-107 Commercial Farm Sevice R-207 Commercial Farm Sevice R-207(Transformer Capacity in Excess of 25kVA) Commercial LPS Rate 12 (Mainland) Industrial LPS Rate 12KI (Kelleys Island) Industrial NR Rate GS-8KI (Kelleys Island) Commercial NR Rate GS-8M (Mainland) Commercial NR Rate GS-9KI - Kelleys Island Over 25 kW Commercial

328

Water Sampling At International Geothermal Area, New Zealand (Wood, 2002) |  

Open Energy Info (EERE)

International Geothermal Area, New Zealand (Wood, 2002) International Geothermal Area, New Zealand (Wood, 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Water Sampling At International Geothermal Area New Zealand (Wood, 2002) Exploration Activity Details Location International Geothermal Area New Zealand Exploration Technique Water Sampling Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes Geothermal fluids from hot springs and wells have been sampled from a number of locations, including: 1) the North Island of New Zealand (three sets of samples from three different years) and the South Island of New Zealand (1 set of samples); 2) the Cascades of Oregon; 3) the Harney, Alvord Desert and Owyhee geothermal areas of Oregon; 4) the Dixie Valley

329

Hogged Wood Fuel Supply and Price Analysis : Final Report.  

SciTech Connect

This study discusses the factors that determine the supply and demand for hogged wood in the Pacific Northwest, with particular emphasis on the role of the regional pulp and paper industry and lumber industry. Because hogged wood is often a substitute for conventional fuels, the consumption and price of natural gas, electricity, fuel oil and coal are also addressed. A detailed and comprehensive examination of the indicies relating to the hogged wood market is provided, including analysis and graphing of all time series variables. A spreadsheet- based forecasting model is developed and presented with an emphasis on explaining the process used to arrive at the final model. 42 refs., 46 figs., 14 tabs. (MHB)

Biederman, Richard T.; Blazek, Christopher F.

1991-05-01T23:59:59.000Z

330

Wood for energy and rural development: the Philippine experience  

Science Conference Proceedings (OSTI)

The Philippine wood energy programme (dendro-thermal system) was originally developed as a source of energy independent of imported oil, and at a lower cost than oil. It has social benefits: new jobs, land distribution, rural income increment, and reforestation by tree farmers. Tree farming, its administration and organization of farmer institutions are essential to the programme, as are the development of farming techniques to produce energy, trees (growth of ipil-ipil), and an improved tree growth rate. An analysis of the economics of wood energy led to the conclusion that raw wood fuel can be cheaper than oil. In estimated costs of electricity, the dendro-thermal plants can produce power at competitive rates. 36 references.

Denton, F.H.

1983-01-01T23:59:59.000Z

331

Water Sampling At Heber Area (Wood, 2002) | Open Energy Information  

Open Energy Info (EERE)

Heber Area (Wood, 2002) Heber Area (Wood, 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Water Sampling At Heber Area (Wood, 2002) Exploration Activity Details Location Heber Area Exploration Technique Water Sampling Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes Geothermal fluids from hot springs and wells have been sampled from a number of locations, including: 1) the North Island of New Zealand (three sets of samples from three different years) and the South Island of New Zealand (1 set of samples); 2) the Cascades of Oregon; 3) the Harney, Alvord Desert and Owyhee geothermal areas of Oregon; 4) the Dixie Valley and Beowawe fields in Nevada; 5) Palinpiiion, the Philippines; 6) the Salton Sea and Heber geothermal fields of southern California; and 7) the

332

Comminution process to produce precision wood particles of uniform size and shape with disrupted grain structure from wood chips  

DOE Patents (OSTI)

A process of comminution of wood chips (C) having a grain direction to produce a mixture of wood particles (P), wherein the wood chips are characterized by an average length dimension (L.sub.C) as measured substantially parallel to the grain, an average width dimension (W.sub.C) as measured normal to L.sub.C and aligned cross grain, and an average height dimension (H.sub.C) as measured normal to W.sub.C and L.sub.C, and wherein the comminution process comprises the step of feeding the wood chips in a direction of travel substantially randomly to the grain direction through a counter rotating pair of intermeshing arrays of cutting discs (D) arrayed axially perpendicular to the direction of wood chip travel, wherein the cutting discs have a uniform thickness (T.sub.D), and wherein at least one of L.sub.C, W.sub.C, and H.sub.C is greater than T.sub.D.

Dooley, James H; Lanning, David N

2013-08-13T23:59:59.000Z

333

Carbon mitigation potential and costs of forestry options in Brazil, China, India, Indonesia, Mexico, the Philippines and Tanzania  

Science Conference Proceedings (OSTI)

This paper summarizes studies of carbon (C) mitigation potential and costs of about 40 forestry options in seven developing countries. Each study uses the same methodological approach - Comprehensive Mitigation Assessment Process (COMAP) - to estimate the above parameters between 2000 and 2030. The approach requires the projection of baseline and mitigation land-use scenarios. Coupled with data on a per ha basis on C sequestration or avoidance, and costs and benefits, it allows the estimation of monetary benefit per Mg C, and the total costs and carbon potential. The results show that about half (3.0 Pg C) the cumulative mitigation potential of 6.2 Petagram (Pg) C between 2000 and 2030 in the seven countries (about 200 x 106 Mg C yr-1) could be achieved at a negative cost and the remainder at costs ranging up to $100 Mg C-1. About 5 Pg C could be achieved, at a cost less than $20 per Mg C. Negative cost potential indicates that non-carbon revenue is sufficient to offset direct costs of these options. The achievable potential is likely to be smaller, however, due to market, institutional, and sociocultural barriers that can delay or prevent the implementation of the analyzed options.

Sathaye, J.; Makundi, W.; Andrasko, K.; Boer, R.; Ravindranath, N.; Sudha, P.; Rao, S.; Lasco, R.; Pulhin, F.; Masera, O.; Ceron, A.; Ordonez, J.; Deying, X.; Zhang, X.; Zuomin, S.

2001-01-01T23:59:59.000Z

334

Clean-Burning Wood Stove Grant Program (Maryland) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Clean-Burning Wood Stove Grant Program (Maryland) Clean-Burning Wood Stove Grant Program (Maryland) Clean-Burning Wood Stove Grant Program (Maryland) < Back Eligibility Residential Savings Category Bioenergy Program Info Start Date 09/07/2012 State Maryland Program Type State Rebate Program Rebate Amount Stick Burning Stove: $500 Pellet Burning Stove: $700 The Maryland Energy Administration (MEA) now offers the Clean Burning Wood Stove Grant program as part of its Residential Clean Energy Grant Program. The Clean Burning Wood Stove Grant program offers a flat grant award of $500 for stick burning wood stoves and $700 for pellet burning wood stoves that meet program eligibility requirements. Basic requirements for grant funding include: *The property must serve as primary residence *Clean burning wood stove must replace existing electric or non-natural gas

335

Residential Bulk-Fed Wood-Pellet Central Boilers and Furnace...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Bulk-Fed Wood-Pellet Central Boilers and Furnace Rebate Program Residential Bulk-Fed Wood-Pellet Central Boilers and Furnace Rebate Program Eligibility Multi-Family Residential...

336

Name: Qinglin Wu Title: Roy O Martin Sr. Professor, Composites and Engineered Wood Products  

E-Print Network (OSTI)

Department: School of Renewable Natural Resources Mailing Address: 107 Renewable-Natural-Resources Building Louisiana Forest Products Development Center (LFPDC) School of Renewable Natural Resources Louisiana State. China. RESEARCH INTERESTS Wood and natural fiber polymer composites, engineered wood products, composite

337

Assessment of existing feuds data base for identification of potential industrial wood users in North Carolina  

DOE Green Energy (OSTI)

The North Carolina Wood Assistance Team's evaluation of the Ultrasystems' computerized methodology for identifying high potential wood conversion facilities is presented. The analysis, methodology, and data are found to be inadequate for the intended use.

Gustashaw, D.H.

1981-03-01T23:59:59.000Z

338

EA-1850: Flambeau River BioFuels, Inc. Proposed Wood Biomass...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

850: Flambeau River BioFuels, Inc. Proposed Wood Biomass-to-Liquid Fuel Biorefinery, Park Falls, Wisconsin EA-1850: Flambeau River BioFuels, Inc. Proposed Wood Biomass-to-Liquid...

339

EA-1811: NewPage Corporation Wood Biomass to Liquid Fuel, Wisconsin...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1: NewPage Corporation Wood Biomass to Liquid Fuel, Wisconsin Rapids, Wisconsin EA-1811: NewPage Corporation Wood Biomass to Liquid Fuel, Wisconsin Rapids, Wisconsin Summary This...

340

Methanol production from eucalyptus wood chips. Attachment VIII. The wood-fueled gasification system, Evergreen Energy Corporation's final engineering report  

DOE Green Energy (OSTI)

Evergreen Energy Corporation provided projected cost and operating data on the Evergreen/Texaco entrained-bed wood gasification system currently under development as an alternative to the state-of-the-art fixed-bed wood gasification system proposed by Davy McKee. Overall capital costs for the total plant remain about the same at approx. $250 million. The Evergreen/Texaco system will provide significant capital cost savings in the gasifiers, gas cleanup, and waste water treatment sections, and eliminate the need for a large off-site wood-fired power boiler. These reductions are offset by higher investments in the feedstock preparation, drying, and feeding section plus the need for a larger air separation plant and compressor to supply oxygen at high pressure to the gasifier.

Fishkind, H.H.

1982-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Field Guide: Visual Inspection of Wood Structures (Optimized for Electronic Viewing)  

Science Conference Proceedings (OSTI)

The Field Guide: Visual Inspection of Wood Structures is a catalog of photographs illustrating various conditions and factors that commonly affect transmission line wood structures, along with their likely causes, a Maintenance Priority Rating, and suggested actions to be taken by utility personnel. Poles, cross-arms, cross-arm braces, X-braces, brackets, anchor rods, guy wires, and direct imbedded foundations are covered. Other sections include types of wood structures, the anatomy of wood ...

2011-11-09T23:59:59.000Z

342

Modern Wood Energy Systems and Markets 16-17 September 2008, Timisoara, Romania  

E-Print Network (OSTI)

Modern Wood Energy Systems and Markets 16-17 September 2008, Timisoara, Romania International Wood Energy Market Developments Ed Pepke Forest Products Marketing Specialist UNECE/FAO Timber Section, Geneva #12;Modern Wood Energy Systems and Markets 16-17 September 2008, Timisoara, Romania Subjects I

343

Development of Wood Chips and Pellets market in Slovakia Jozef Viglasky, SK-BIOM, Slovakia  

E-Print Network (OSTI)

is supported by the Danish Government. One of the main barriers for extension of wood pellet production is lack1 Development of Wood Chips and Pellets market in Slovakia Jozef Viglasky, SK-BIOM, Slovakia-combustion of wood residues in existing coal fired power systems. #12;3 · Implementation of low cost anaerobic

344

Hydrologic and Water-Quality Conditions During Restoration of the Wood River Wetland,  

E-Print Network (OSTI)

.S. Geological Survey #12;Front Cover: Aerial view of the lower Wood River Valley showing the Wood River Wetland.S. Geological Survey, January 2003. #12;Hydrologic and Water-Quality Conditions During Restoration of the Wood­5004 U.S. Department of the Interior U.S. Geological Survey #12;U.S. Department of the Interior KEN

345

Discrimination of bark from wood chips through texture analysis by image processing  

Science Conference Proceedings (OSTI)

Utilization of wood chips for bioenergy requires classification and segregation of the constituents of the chipped mass to help optimize energy conversion. Wood chips obtained from processes such as forest thinning can contain a considerable amount of ... Keywords: Bark, Biomass, Image processing, Texture analysis, Wood chip

James R. Wooten; S. D. Filip To; C. Igathinathane; L. O. Pordesimo

2011-10-01T23:59:59.000Z

346

EFFECTS OF SAMPLE SIZE ON CHARACTERIZATION OF WOOD-PARTICLE LENGTH DISTRIBUTION  

E-Print Network (OSTI)

EFFECTS OF SAMPLE SIZE ON CHARACTERIZATION OF WOOD-PARTICLE LENGTH DISTRIBUTION Quang V. Cao of sample size on fitting length distribution of wood particles used for manufacturing wood-based composites moments and the ability of the sample distributions to characterize the population represented

347

Design of wood biomass supply chains  

Science Conference Proceedings (OSTI)

The purpose of this paper is to propose a mathematical programming approach to minimize the total cost in a biomass supply chain. A company that collects material from forests, transforms it into chipped product, stores and delivers it to its customers ... Keywords: biomass, mixed integer programming, optimization, supply chain

Tiago Costa Gomes; Filipe Pereira e Alvelos; Maria Sameiro Carvalho

2012-06-01T23:59:59.000Z

348

Thermal Impact of Fasteners in High-Performance Wood-Framed Walls: Preprint  

SciTech Connect

Buildings are heavy consumers of energy, and residential building design is rapidly addressing topics to maximize energy conservation en route to net-zero energy consumption. Annual energy analysis of a building informs the choice among disparate energy measures, for cost, durability, occupant comfort, and whole-house energy use. Physics-based and empirical models of elements of a building are used in such analyses. High-performance wood-framed walls enable builders to construct homes that use much less than 40% of the energy consumed by similar homes built to minimum code. Modeling for these walls has considered physical features such as framing factor, insulation and framing properties, roughness and convective effects, and air leakage. The thermal effects of fasteners used to construct these walls have not been fully evaluated, even though their thermal conductivity is orders of magnitudes higher than that of other building materials. Drywall screws and siding nails are considered in this finite element thermal conductivity analysis of wall sections that represent wood-framed walls that are often used in high-performance homes. Nails and screws reduce even the best walls' insulating performance by approximately 3% and become increasingly significant as the framing factor increases.

Christensen, D.

2011-01-01T23:59:59.000Z

349

Thermal Impact of Fasteners in High-Performance Wood-Framed Walls: Preprint  

SciTech Connect

Buildings are heavy consumers of energy, and residential building design is rapidly addressing topics to maximize energy conservation en route to net-zero energy consumption. Annual energy analysis of a building informs the choice among disparate energy measures, for cost, durability, occupant comfort, and whole-house energy use. Physics-based and empirical models of elements of a building are used in such analyses. High-performance wood-framed walls enable builders to construct homes that use much less than 40% of the energy consumed by similar homes built to minimum code. Modeling for these walls has considered physical features such as framing factor, insulation and framing properties, roughness and convective effects, and air leakage. The thermal effects of fasteners used to construct these walls have not been fully evaluated, even though their thermal conductivity is orders of magnitudes higher than that of other building materials. Drywall screws and siding nails are considered in this finite element thermal conductivity analysis of wall sections that represent wood-framed walls that are often used in high-performance homes. Nails and screws reduce even the best walls' insulating performance by approximately 3% and become increasingly significant as the framing factor increases.

Christensen, D.

2011-01-01T23:59:59.000Z

350

Woods Hole Research Center Wind Turbine | Open Energy Information  

Open Energy Info (EERE)

Hole Research Center Wind Turbine Hole Research Center Wind Turbine Jump to: navigation, search Name Woods Hole Research Center Wind Turbine Facility Woods Hole Research Center Wind Turbine Sector Wind energy Facility Type Small Scale Wind Facility Status In Service Owner Woods Hole Research Center Developer Sustainable Energy Developments Energy Purchaser Woods Hole Research Center Location Falmouth MA Coordinates 41.548637°, -70.64326° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.548637,"lon":-70.64326,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

351

Wood Waste -A Modern Fuel M. A. SERRELL, P. E.  

E-Print Network (OSTI)

, designed like the vanes of a fan WOOD BO'LER SACK r-v'"",", __--J DAMF[R · I ... .... .... .... ... ... FAN and provides automatic steam generation on an unattended basis. A flyash arrestor with induced draft fan fashioned boiler design where the boiler shell is pierced by a number of longitudinal fire tubes which run

Columbia University

352

Production of chemical feedstock by the methanolysis of wood  

DOE Patents (OSTI)

A process is discussed for the production of ethylene, benzene and carbon monoxide from particulated biomass such as wood by reaction with methane at a temperature of from 700/sup 0/C to 1200/sup 0/C, at a pressure of from 20 psi to 100 psi for a period of from 0.2 to 10 seconds.

Steinberg, M.; Fallon, P.

1983-06-01T23:59:59.000Z

353

Short rotation wood crops program: Annual progress report for 1986  

DOE Green Energy (OSTI)

This report describes accomplishments in the Short Rotation Woody Crops Program (SRWCP) for the year ending September 30, 1986. The program is sponsored by the US Department of Energy's Biofuels and Municipal Waste Technology Division and consists of research projects at 29 institutions and corporations. The SRWCP is an integrated program of research and development devoted to a single objective: improving the productivity, cost efficiency, and fuel quality of wood energy crops as feedstocks for conversion to liquid and gaseous fuels. SRWCP directives have shifted from species-screening and productivity evaluations to large-scale viability trials of model species selected for their productivity potential and environmental compatibility. Populus was chosen the lead genera of five model species, and initial steps were taken toward organizing a Populus Research Consortium. Production yields from SRWCP research plots and coppice studies are discussed along with new efforts to model growth results and characteristics on a tree and stand basis. Structural and chemical properties of short-rotation intensive culture wood have been evaluated to determine the desirability of species traits and the potential for genetic improvements. Innovative wood energy crop handling techniques are presented as significant cost reduction measures. The conclusion is that new specialized wood energy crops can be feasible with the advances that appear technically possible over the next 10 years. 34 refs., 9 figs., 7 tabs.

Ranney, J.W.; Wright, L.L.; Layton, P.A.; McNabb, W.A.; Wenzel, C.R.; Curtin, D.T.

1987-11-01T23:59:59.000Z

354

Wood Products Marketing And Value-Added Opportunities  

E-Print Network (OSTI)

Point, NC, 27261, USA Tel.: (336) 841 8535 Fax.: (336) 841 5435 151 Randall St. Oakville, ON Canada, L6J SituationThe Situation As global populations continue to grow, the demand for wood products will increase in: Cultures Technology Infrastructure #12;Demand: Overall ClimateDemand: Overal

355

Temperature Measurements in Full-Scale Wood Stud Shear Walls  

E-Print Network (OSTI)

This report presents the results of 10 full-scale fire resistance tests conducted at the National Fire Laboratory on load-bearing gypsum board protected, wood stud shear wall assemblies with and without resilient channels on the fire-exposed side. The two assembly arrangements studied were: symmetrical installation 1x1 (one layer of gypsum board on each of the exposed and unexposed sides) and asymmetrical installation of the shear membrane (one layer of gypsum board on both the exposed and unexposed sides and a shear wall membrane as a base layer alternating between the exposed (2x1) and unexposed sides (1x2)) on a wood stud frame. The gypsum board was 12.7 mm thick Type X. The insulations used were glass and rock fibres. The shear membranes used were plywood and oriented strand board (OSB). Tests were conducted to determine the effects of the placement of the shear membrane on the exposed/unexposed face, type of shear membrane, insulation type, load intensity and resilient channel installations on the fire resistance of gypsum board protected, wood stud shear wall assemblies. Details of the results, including the temperatures and deflections measured during the fire tests, are presented. ACKNOWLEDGEMENTS This research is part of a consortium project on the fire resistance and sound performance of wall assemblies - Phase II, among the following partners: . Canadian Wood Council . Canadian Home Builders Association . Canadian Sheet Steel Building Institute . Gypsum Manufacturers of Canada . Owens-Corning Canada . Roxul Inc.

V. K. R. Sultan; M. A. Denham; V. K. R. Kodur; M. A. Sultan; E. M. A. Denham; Canadian Wood Council; Shear Walls; Shear Walls; Shear Walls; Shear Walls

1996-01-01T23:59:59.000Z

356

Production of chemical feedstock by the methanolysis of wood  

DOE Patents (OSTI)

A process for the production of ethylene, benzene and carbon monoxide from particulated biomass such as wood by reaction with methane at a temperature of from 700.degree. C. to 1200.degree. C., at a pressure of from 20 psi to 100 psi for a period of from 0.2 to 10 seconds.

Steinberg, Meyer (Melville, NY); Fallon, Peter (East Moriches, NY)

1984-07-31T23:59:59.000Z

357

Wood pellet market and trade: a global perspective  

SciTech Connect

This perspective provides an overview of wood pellet markets in a number of countries of high significance, together with an inventory of market factors and relevant past or existing policies. In 2010, the estimated global wood pellet production and consumption were close to 14.3 Mt (million metric tonnes) and 13.5 Mt, respectively, while the global installed production capacity had reached over 28 Mt. Two types of pellets are mainly traded (i) for residential heating and (ii) for large-scale district heating or co-fi ring installations. The EU was the primary market, responsible for nearly 61% and 85% of global production and consumption, respectively in 2010. EU markets were divided according to end use: (i) residential and district heating, (ii) power plants driven market, (iii) mixed market, and (iv) export-driven countries. North America basically serves as an exporter, but also with signifi cant domestic consumption in USA. East Asia is predicted to become the second-largest consumer after the EU in the near future. The development perspective in Latin America remains unclear. Five factors that determine the market characteristics are: (i) the existence of coal-based power plants, (ii) the development of heating systems, (iii) feedstock availability, (iv) interactions with wood industry, and (v) logistics factor. Furthermore, intervention policies play a pivotal role in market development. The perspective of wood pellets industry was also analyzed from four major aspects: (i) supply potential, (ii) logistics issues, (iii) sustainability considerations, and (iv) technology development.

Chun Sheng Goh; Martin Junginger; Maurizio Cocchi; Didier Marchal; Daniela Thran; Christiane Hennig; Jussi Heinimo; Lars Nikolaisen; Peter-Paul Schouwenberg; Douglas Bradley; J. Richard Hess; Jacob J. Jacobson; Leslie Ovard; Michael Deutmeyer

2001-01-01T23:59:59.000Z

358

Environmental Impacts of Preservative-Treated Wood Conference  

E-Print Network (OSTI)

This article was written and prepared by U.S. Government employees on official time, For decades chromated copper arsenate (CCA) was the primary preservative for treated wood used in residential construction. However, recent label changes submitted by CCA registrants will withdraw CCA from most residential applications. This action has increased interest in arsenic-free preservative systems that have been standardized by the American Wood Preservers ’ Association. These include acid copper chromate (ACC), alkaline copper quat (ACQ), copper azole (CBA-A and CA-B), copper citrate (CC), copper dimethyldithiocarbamate (CDDC), and copper HDO (CX-A). All of these CCA alternatives rely on copper as their primary biocide, although some have co-biocides to help prevent attack by copper-tolerant fungi. They have appearance and handling properties similar to CCA and are likely to be readily accepted by consumers. Prior studies indicate that these CCA alternatives release preservative components into the environment at a rate greater than or equal to that of CCA, but because these components have lower mammalian toxicity they are less likely to cause concern in residential applications. As the treated wood industry evolves it is probable that a wider range of types and retentions of wood preservatives will become available, with the treatment more closely tailored to a specific type of construction application.

Stan Lebow

2004-01-01T23:59:59.000Z

359

Wood Products Marketing And Value-Added Opportunities  

E-Print Network (OSTI)

; Vlosky 2002 #12;s The first MDF plant started up four years ago and now there are 3 or 4, so furniture for exotic wood veneer layup. Pressing veneer on MDF will give the most defect-free, flat and smooth surface

360

Scattering of Woods-Saxon Potential in Schrodinger Equation  

E-Print Network (OSTI)

The scattering solutions of the one-dimensional Schrodinger equation for the Woods-Saxon potential are obtained within the position-dependent mass formalism. The wave functions, transmission and reflection coefficients are calculated in terms of Heun's function. These results are also studied for the constant mass case in detail.

Altug Arda; Oktay Aydogdu; Ramazan Sever

2010-09-27T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Mitigation for the Endangered Wood Stork on Savannah River Site  

DOE Green Energy (OSTI)

The wood stork is a recently classified federally endangered species. The species forages throughout the facility. The facility impact was mitigated by replacing the affected area with artificially created impoundment. Studies conducted in conjunction with the mitigation have assisted with the recovery effort for this species.

Bryan, A.L.; Coulter, M.C.; Brisbin, I.L.

2000-10-01T23:59:59.000Z

362

Re-conservation of Wood from the Seventeenth-Century Swedish Warship the Vasa with Alkoxysilanes: A Re-treatment Study Applying Thermosetting Elastomers  

E-Print Network (OSTI)

The purpose of this study was to explore the feasibility of re-treating artifacts previously conserved by PEG impregnation with alkoxysilanes. The study tried to evaluate pros and cons of re-conserving artifacts with this type of silanes. A series of experiments were conducted focusing on small, wood samples from the Vasa Museum Collection, to test different re-conservation methods. Three different procedures involving alkoxysilanes were implemented in order to re-conserve the samples. The study revealed the techniques are an efficient re-conservation method in which highly satisfactory results can be achieved. The re-treated samples present minimal volumetric distortion without significant collapse or shrinkage of the wood structures. This minimal distortion is primarily produced by the transition from swollen waterlogged wood to a dry conserved wood, and not as a result of collapse or shrinkage during treatment. Due to the negligible thickness of the polymer coating (a few microns), the samples acquire physical properties extremely close to the original dry wood. Moreover, other physiochemical properties are obtained from the consolidation with alkoxysilanes; the re-conserved wood becomes hydrophobic, chemically inert, resistant to chemical attacks (e.g., acids or bases), and resistant to ultraviolet light. These newly acquired characteristics drastically reduce the preventive conservation measures needed in museum display cabinets or during transport. Despite the excellent results, the procedure is not reversible, thus does not comply with one of the main premises traditionally accepted in conservation. Therefore, a careful study assessing benefits and disadvantages in a case-by-case basis should be assessed by conservators, restorers, and curators before applying this method to waterlogged material culture.

Cabrera Tejedor, Carlos

2010-12-01T23:59:59.000Z

363

Investigation of the Effect of In-Situ Catalyst on the Steam Hydrogasification of Biomass  

E-Print Network (OSTI)

Conversion Biomass Energy Forestry Biochemical Biopower - Logging - Anaerobic digestion - Heat - Wood, paper mills - Hydrolysis/ Fermentation - Electricity Agricultural Thermal/chemical

FAN, XIN

2012-01-01T23:59:59.000Z

364

Technical and economic review of wood energy systems for military bases  

DOE Green Energy (OSTI)

This report combines two reports dealing with industrial-sized wood combustion technology. As part of its industrial wood combustion effort, SERI's former Industrial Applications and Analysis Branch (IAAB) contracted with the Air Force through the Department of Energy (DOE) to review wood fuels and equipment and to perform an economic sensitivity analysis of small-scale industrial-sized wood combustion investments that might be considered for steam and/or electricity generation at Air Force Bases. Additionally, in 1979, SERI's IAAB contracted with North Carolina State University to produce the Decision Makers' Guide to Wood Fuel for Small Industrial Energy Use. These two reports have been combined to provide the Air Force with a comprehensive guide to wood energy combustion. Discussion is presented under the headings: comparison of wood fuels with conventional boiler fuels; densified biomass; fuel storage; fuel handling and preparation; wood-fired equipment; gasification of wood; retrofitting fossil-fuel boilers; cogeneration; pollution abatement; wood energy system economics and procurement of wood fuels. (DMC)

Flowers, L.; Junge, D.; Levi, M.; O'Grady, M.

1983-06-01T23:59:59.000Z

365

How Much Wood Would a North Country School Chip | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How Much Wood Would a North Country School Chip How Much Wood Would a North Country School Chip How Much Wood Would a North Country School Chip November 3, 2011 - 11:19am Addthis This is the North Country School's 32,000-square-foot main building. Aligning with the school's commitment to a simple, sustainable lifestyle, the school is heated with a wood chip boiler that uses wood sourced from their sustainably managed woodlot and local forests. | Courtesy of North Country School This is the North Country School's 32,000-square-foot main building. Aligning with the school's commitment to a simple, sustainable lifestyle, the school is heated with a wood chip boiler that uses wood sourced from their sustainably managed woodlot and local forests. | Courtesy of North Country School Alice Dasek Project Officer, Department of Energy State Energy Program

366

How Much Wood Would a North Country School Chip | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How Much Wood Would a North Country School Chip How Much Wood Would a North Country School Chip How Much Wood Would a North Country School Chip November 3, 2011 - 11:19am Addthis This is the North Country School's 32,000-square-foot main building. Aligning with the school's commitment to a simple, sustainable lifestyle, the school is heated with a wood chip boiler that uses wood sourced from their sustainably managed woodlot and local forests. | Courtesy of North Country School This is the North Country School's 32,000-square-foot main building. Aligning with the school's commitment to a simple, sustainable lifestyle, the school is heated with a wood chip boiler that uses wood sourced from their sustainably managed woodlot and local forests. | Courtesy of North Country School Alice Dasek Project Officer, Department of Energy State Energy Program

367

URBAN WOOD/COAL CO-FIRING IN THE NIOSH BOILER PLANT  

DOE Green Energy (OSTI)

Phase I of this project began by obtaining R&D variances for permits at the NIOSH boilerplant (NBP), Emery Tree Service (ETS) and the J. A. Rutter Company (JARC) for their portions of the project. Wood for the test burn was obtained from the JARC inventory (pallets), Thompson Properties and Seven D Corporation (construction wood), and the Arlington Heights Housing Project (demolition wood). The wood was ground at ETS and JARC, delivered to the Three Rivers Terminal and blended with coal. Three one-day tests using wood/coal blends of 33% wood by volume (both construction wood and demolition wood) were conducted at the NBP. Blends using hammermilled wood were operationally successful. Emissions of SO{sub 2} and NOx decreased and that of CO increased when compared with combusting coal alone. Mercury emissions were measured and evaluated. During the first year of Phase II the principal work focused upon searching for a replacement boilerplant and developing a commercial supply of demolition wood. The NBP withdrew from the project and a search began for another stoker boilerplant in Pennsylvania to replace it on the project. Three potential commercial demolition wood providers were contacted. Two were not be able to supply wood. At the end of the first year of Phase II, discussions were continuing with the third one, a commercial demolition wood provider from northern New Jersey. During the two-and-a-third years of the contract extension it was determined that the demolition wood from northern New Jersey was impractical for use in Pittsburgh, in another power plant in central New Jersey, and in a new wood gasifier being planned in Philadelphia. However, the project team did identify sufficient wood from other sources for the gasifier project. The Principal Investigator of this project assisted a feasibility study of wood gasification in Clarion County, Pennsylvania. As a result of the study, an independent power producer in the county has initiated a small wood gasification project at its site. Throughout much of this total project the Principal Investigator has counseled two small businesses in developing a waxed cardboard pellet business. A recent test burn of this biofuel appears successful and a purchase contract is anticipated soon. During the past two months a major tree-trimming firm has shown an active interest in entering the wood-chip fuel market in the Pittsburgh area and has contacted the NBP, among others, as potential customers. The NBP superintendent is currently in discussion with the facilities management of the Bruceton Research Center about resuming their interest in cofiring this renewable fuel to the stoker there.

James T. Cobb Jr.

2005-02-10T23:59:59.000Z

368

Co-combustion of textile residues with cardboard and waste wood in a packed bed  

SciTech Connect

The combustible fraction of the municipal waste is mostly bio-derived. Energy recovery of the wastes that cannot be economically recycled is a key part of sustainable energy policy and waste management. Textile residues have high energy content. When burned alone in a packed bed system, however, their combustion efficiency is low due to the irregular propagation of the ignition front and the low burning rates. In order to achieve more efficient combustion of textile residues, a series of co-combustion tests were carried out for various mixture compositions and air flow rates in a packed bed combustor. The combustion performance of these materials was evaluated by using quantitative measures such as ignition rate, burning rate and equivalence ratio. Co-combustion of textile residues with cardboard for a textile fraction of up to 30% achieved satisfactorily high burning rate and low unburned carbon content in the bottom ash. The mixture was more resistant to convective cooling by air, which significantly expanded the range of air flow rate for combustion at high burning rates. In co-combustion with a material that has a very low ignition front speed such as waste wood, the propagation of the ignition front was governed by textile residues. Therefore, the co-combustion of textile residues can be better performed with a material having similar ignition front speeds, in which the two materials simultaneously burn at the ignition front. (author)

Ryu, Changkook; Phan, Anh N; Sharifi, Vida N; Swithenbank, Jim [Sheffield University Waste Incineration Centre (SUWIC), Department of Chemical and Process Engineering, The University of Sheffield, Mappin Street, Sheffield S1 3JD (United Kingdom)

2007-11-15T23:59:59.000Z

369

Huntington Woods, Michigan: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Woods, Michigan: Energy Resources Woods, Michigan: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 42.4805913°, -83.1668713° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.4805913,"lon":-83.1668713,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

370

Wood-Ridge, New Jersey: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Wood-Ridge, New Jersey: Energy Resources Wood-Ridge, New Jersey: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 40.8456555°, -74.0879195° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.8456555,"lon":-74.0879195,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

371

Meadow Woods, Florida: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Woods, Florida: Energy Resources Woods, Florida: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 28.3855632°, -81.366459° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":28.3855632,"lon":-81.366459,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

372

Mission Woods, Kansas: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Mission Woods, Kansas: Energy Resources Mission Woods, Kansas: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 39.0350053°, -94.6085677° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.0350053,"lon":-94.6085677,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

373

MEMORANDUM TO: F ROM: GREGORY H. WOODS GENERAL COUNSEL  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

February 4, 2013 February 4, 2013 MEMORANDUM TO: F ROM: GREGORY H. WOODS GENERAL COUNSEL CHRISTOPHER A.SMITH �|=K= ACTING ASSISTANT SECRETARY FOR FOSSIL ENERGY SUBJECT: Annual National Environmental Policy Act (NEPA) Planning Summaries for 2013 ISSUE: DOE Order 451.1B, Section 4.d, requires that an annual planning summary be prepared that briefly describes: {1) any Environmental Assessments (EAs) ongoing or expected to be

374

Wood Gasification: Where It's At, Where It's Going  

E-Print Network (OSTI)

This paper discusses the principles and practice of various designs of biomass/wood gasifiers. In general, the basic principle of gasification is reviewed. A look at existing gasifier schemes, including packed bed updraft, downdraft, and fluidized bed, defines the basic characteristics of each and their advantages and di advantages. The economics of using one type of system - a fluid bed gasifier, on an oil fired boiler is presented to depict a representative, if not conservative, payback time for such an investment.

Murphy, M. L.

1981-01-01T23:59:59.000Z

375

Quality of Wood Pellets Produced in British Columbia for Export  

Science Conference Proceedings (OSTI)

Wood pellet production and its use for heat and power production are increasing worldwide. The quality of export pellets has to consistently meet certain specifications as stipulated by the larger buyers, such as power utilities or as specified by the standards used for the non-industrial bag market. No specific data is available regarding the quality of export pellets to Europe. To develop a set of baseline data, wood pellets were sampled at an export terminal in Vancouver, British Columbia, Canada. The sampling period was 18 months in 2007-2008 when pellets were transferred from storage bins to the ocean vessels. The sampling frequency was once every 1.5 to 2 months for a total of 9 loading/shipping events. The physical properties of the wood pellets measured were moisture content in the range of 3.5% to 6.5%, bulk density from 728 to 808 kg/m3, durability from 97% to 99%, fines content from 0.03% to 0.87%, calorific value as is from 17 to almost 18 MJ/kg, and ash content from 0.26% to 0.93%.The diameter and length were in the range of 6.4 to 6.5 mm and 14.0 to 19.0 mm, respectively. All of these values met the published non-industrial European grades (CEN) and the grades specified by the Pellet Fuel Institute for the United States for the bag market. The measured values for wood pellet properties were consistent except the ash content values decreased over the test period.

J. S. Tumuluru; S. Sokhansanj; C. J. Lim; T. Bi; A. Lau; S. Melin; T. Sowlati; E. Oveisi

2010-11-01T23:59:59.000Z

376

QUALITY OF WOOD PELLETS PRODUCED IN BRITISH COLUMBIA FOR EXPORT  

Science Conference Proceedings (OSTI)

Wood pellet production and its use for heat and power production are increasing worldwide. The quality of export pellets has to consistently meet certain specifications as stipulated by the larger buyers, such as power utilities or as specified by the standards used for the non-industrial bag market. No specific data is available regarding the quality of export pellets to Europe. To develop a set of baseline data, wood pellets were sampled at an export terminal in Vancouver, British Columbia, Canada. The sampling period was 18 months in 2007-2008 when pellets were transferred from storage bins to the ocean vessels. The sampling frequency was once every 1.5 to 2 months for a total of 9 loading/shipping events. The physical properties of the wood pellets measured were moisture content in the range of 3.5% to 6.5%, bulk density from 728 to 808 kg/m3, durability from 97% to 99%, fines content from 0.03% to 0.87%, calorific value as is from 17 to almost 18 MJ/kg, and ash content from 0.26% to 0.93%.The diameter and length were in the range of 6.4 to 6.5 mm and 14.0 to 19.0 mm, respectively. All of these values met the published non-industrial European grades (CEN) and the grades specified by the Pellet Fuel Institute for the United States for the bag market. The measured values for wood pellet properties were consistent except the ash content values decreased over the test period.

Tumuluru, J.S. [Idaho National Laboratory (INL); Sokhansanj, Shahabaddine [ORNL; Lim, C. Jim [University of British Columbia, Vancouver; Bi, X.T. [University of British Columbia, Vancouver; Lau, A.K. [University of British Columbia, Vancouver; Melin, Staffan [University of British Columbia, Vancouver; Oveisi, E. [University of British Columbia, Vancouver; Sowlati, T. [University of British Columbia, Vancouver

2010-11-01T23:59:59.000Z

377

Report on Wood Pole and Crossarm Degradation Modes  

Science Conference Proceedings (OSTI)

This report covers the typical types of wood used in transmission line construction. The species can be categorized by their level of corrosion resistance, the type of preservative treatment that is appropriate and the type of decay that is predominant. This market has the benefit of experience and training gained through years of pole maintenance practices, research and the techniques that migrate directly to crossarm maintenance.

2009-12-23T23:59:59.000Z

378

Tectonic Setting of the Wooded Island Earthquake Swarm, Eastern Washington  

SciTech Connect

Magnetic anomalies provide insights into the tectonic implications of a swarm of ?1500 shallow (?1 km deep) earthquakes that occurred in 2009 on the Hanford site,Washington. Epicenters were concentrated in a 2 km2 area nearWooded Island in the Columbia River. The largest earthquake (M 3.0) had first motions consistent with slip on a northwest-striking reverse fault. The swarm was accompanied by 35 mm of vertical surface deformation, seen in satellite interferometry (InSAR), interpreted to be caused by ?50 mm of slip on a northwest-striking reverse fault and associated bedding-plane fault in the underlying Columbia River Basalt Group (CRBG). A magnetic anomaly over exposed CRBG at Yakima Ridge 40 km northwest of Wooded Island extends southeastward beyond the ridge to the Columbia River, suggesting that the Yakima Ridge anticline and its associated thrust fault extend southeastward in the subsurface. In map view, the concealed anticline passes through the earthquake swarm and lies parallel to reverse faults determined from first motions and InSAR data. A forward model of the magnetic anomaly near Wooded Island is consistent with uplift of concealed CRBG, with the top surface <200 m below the surface. The earthquake swarm and the thrust and bedding-plane faults modeled from interferometry all fall within the northeastern limb of the faulted anticline. Although fluids may be responsible for triggering the Wooded Island earthquake swarm, the seismic and aseismic deformation are consistent with regional-scale tectonic compression across the concealed Yakima Ridge anticline.

Blakely, Richard J.; Sherrod, Brian; Weaver, Craig; Rohay, Alan C.; Wells, Ray E.

2012-08-02T23:59:59.000Z

379

Particulate matter emissions from combustion of wood in district heating applications  

Science Conference Proceedings (OSTI)

The utilization of wood biomass to generate district heat and power in communities that have access to this energy source is increasing. In this paper the effect of wood fuel properties, combustion condition, and flue gas cleaning system on variation in the amount and formation of particles in the flue gas of typical district heating wood boilers are discussed based on the literature survey. Direct measurements of particulate matter (PM) emissions from wood boilers with district heating applications are reviewed and presented. Finally, recommendations are given regarding the selection of wood fuel, combustion system condition, and flue gas cleaning system in district heating systems in order to meet stringent air quality standards. It is concluded that utilization of high quality wood fuel, such as wood pellets produced from natural, uncontaminated stem wood, would generate the least PM emissions compared to other wood fuel types. Particulate matter emissions from grate burners equipped with electrostatic precipitators when using wood pellets can be well below stringent regulatory emission limit such as particulate emission limit of Metro Vancouver, Canada.

Ghafghazi, S. [University of British Columbia, Vancouver; Sowlati, T. [University of British Columbia, Vancouver; Sokhansanj, Shahabaddine [ORNL; Bi, X.T. [University of British Columbia, Vancouver; Melin, Staffan [Delta Research Corporation

2011-01-01T23:59:59.000Z

380

Materials Science  

Science Conference Proceedings (OSTI)

Materials Science. Summary: ... Description: Group focus in materials science (inkjet metrology, micro-macro, advanced characterizations). ...

2012-10-02T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Low VOC drying of lumber and wood panel products. Progress report No. 7  

DOE Green Energy (OSTI)

Green pine blocks (2x1x 1) were dried to different moisture levels at 120 degrees C. They were immersed in D{sub 2}O (greater than 99% isotopic Content) for different periods at room temperature, and were then cut in halves. One piece from each set was then wrapped in plastic, and microwaved at 110 W, for 30 minutes, with the field being cycled to keep the wood surface at 90-100 degrees C. Fibers taken from just inside the wet surface from five regions along the length of the piece were then analysed by mass spectrometry with a direct insertion probe. The m/e profiles of the three isotopic forms of water, namely H{sub 2}O, HOD, and D{sub 2}O, remained unchanged as the wood was heated inside the spectrometer, indicating that they were bound equally strongly to the wood. The water released from the green wood had the same isotopic composition regardless of whether or not the wood was microwaved (Table 1), indicating that the exchangeable protons in wood were not affected by microwaving. However, as the wood progressively dried, the water released from the microwaved wood was of lower isotopic content, which means that microwaving increases access of the exchangeable protons in wood tissue to water. The only exchangeable protons in dried wood are those sited on hydroxyl groups, and the difference in isotopic exchange is the greatest for dried wood. This must mean that as wood dries, internal hydrogen bonding restricts access of D{sub 2}O to the hydroxyl protons. Presumably the energy transferred to water upon microwaving is sufficient to at least partially overcome this barrier. The effect is akin to the hysteresis that occurs for moisture sorption to green and dried wood. Similar isotope exchange work with D{sub 2}O has been previously conducted to determine the accessibility of cellulose to water.

Hui Yan; Hooda, Usha; Banerjee, Sujit [and others

1998-03-01T23:59:59.000Z

382

Water geochemistry of hydrothermal systems, Wood River District, Idaho  

DOE Green Energy (OSTI)

Hydrothermal systems of the Wood River District, central Idaho, have been studied by geologic mapping of thermal spring areas and geochemical investigations of thermal and non-thermal waters. This report summarizes the new geochemical data gathered during the study. Integration of the results of geological and geochemical studies has led to development of a target model for hydrothermal resources on the margin of the Idaho Batholith. Warfield Hot Springs, with temperatures up to 58/sup 0/C, flow from a major shear zone along the margin of an apophysis of the batholith. Hailey Hot Springs, with temperatures up to 60/sup 0/C, occur in an area of multiple thrust faults and newly recognized, closely spaced normal faults in the Paleozoic Milligen and Wood River Formations, 2.5 km from a highly brecciated batholith contact. Other Wood River district hydrothermal systems also occur along the margins of batholith apophyses or in adjacent highly fractured Paleozoic rocks, where there are indications of batholith rocks at shallow depths (100 to 300 m) in water wells.

Zeisloft, J.; Foley, D.; Blackett, R.

1983-08-01T23:59:59.000Z

383

Long-term lime pretreatment of poplar wood  

E-Print Network (OSTI)

Lignocellulosic biomass (e.g., poplar wood) provides a unique and sustainable resource for environmentally safe organic fuels and chemicals. The core of this study is the pretreatment step involved in bioconversion processes. Pretreatment is required to realize high yields vital to commercial success. The focus of the pretreatment step is to methodically change key features of the biomass to favor enzymatic hydrolysis. This work assesses the compositional changes due to oxidative and non-oxidative longterm lime pretreatment of poplar wood (up to 4 weeks of pretreatment) at mild temperatures (25ºC to 65ºC), and their effect on the enzymatic yield of glucan and xylan. The most important pretreatment yield of lignin was 54 g lignin remaining/100 g lignin in raw biomass, and was accomplished for 4-week lime pretreatment at 65ºC in oxidative conditions. The corresponding pretreatment yields of glucan and xylan were 85.9 g glucan recovered/100 g glucan in raw biomass and 80.2 g xylan recovered/100 g xylan in raw biomass respectively. For poplar wood oxidatively pretreated with lime for 4 weeks at 65ºC and enzymatically hydrolyzed with an enzyme loading of 15 FPU/g glucan in raw biomass during a 3-day period, the best overall yields of glucan and xylan, were 80.7 g glucan hydrolyzed/100 g glucan in raw biomass and 66.9 g xylan hydrolyzed/100 g xylan in raw biomass respectively. The corresponding hydrolysis yields were 94.0 g glucan hydrolyzed/100 g glucan in treated biomass and 83.5 g xylan hydrolyzed/100 g xylan in treated biomass respectively. Because there is a previous study of long-term lime pretreatment of corn stover (Kim, 2004), the data obtained in this work show the effect of using woody lignocellulose as substrate. From the comparison, resulted that in the case of poplar wood oxidatively pretreated at 65ºC for 4 weeks, less lignin was removed and more carbohydrates were solubilized, however the hydrolysis yield of glucan was almost equal and the hydrolysis yield of xylan was higher than the reported by Kim for corn stover oxidatively pretreated at 55ºC for 4 weeks. The overall yield of glucan resulted lower in the case of poplar wood because of the lower pretreatment yield of glucan. Thus, it is important to complete the mass balances including an analysis on the pretreatment liquor to determine if the solubilized glucan was degraded.

Sierra Ramirez, Rocio

2005-12-01T23:59:59.000Z

384

Forestry Policies (Missouri)  

Energy.gov (U.S. Department of Energy (DOE))

Missouri's Forests are managed by the Department of Conservation. In 2010 the Department issued the State's Forest Resource Assessment and Strategy, which identified the goal of steering emerging...

385

Fuels for Schools Program Uses Leftover Wood to Warm Buildings | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fuels for Schools Program Uses Leftover Wood to Warm Buildings Fuels for Schools Program Uses Leftover Wood to Warm Buildings Fuels for Schools Program Uses Leftover Wood to Warm Buildings May 10, 2010 - 1:11pm Addthis Darby Schools received a woodchip heating system in 2003. Rick Scheele, facilities manager for the Darby schools, shows off the wood firebox | Photo Courtesy USFS Fuels for Schools, Dave Atkins Darby Schools received a woodchip heating system in 2003. Rick Scheele, facilities manager for the Darby schools, shows off the wood firebox | Photo Courtesy USFS Fuels for Schools, Dave Atkins Stephen Graff Former Writer & editor for Energy Empowers, EERE In parts of this country, wood seems like the outsider in the biomass family. New ethanol plants that grind down millions of bushels of corn in the Midwest and breakthroughs in algae along the coasts always garner the

386

Expert Paper for the UNECE, Timber Committee Market Discussions, Geneva, 7-8 October 2003 1 Trends and Market Effects of Wood Energy Policies  

E-Print Network (OSTI)

is the future direction of electricity production from wood and co-firing of wood in coal power plants and pulp and paper production; ethanol and wood pellets projects have been more directed production from wood and co-firing of wood in coal power plants is the variable with the highest potential

387

Materials-Environment Interactions  

Science Conference Proceedings (OSTI)

Oct 18, 2011 ... Program Organizers: Chris Wood, TMS ... Spraying, with pre and post heating, and HVOF process on substrates of AISI 304 austenitic steel.

388

Materials Technology @ TMS  

Science Conference Proceedings (OSTI)

Jul 30, 2010... power plant that uses clean wood fuel to produce electricity. DownEast sells electricity output and capacity into the ISO New England market.

389

Ultrafine Grained Materials III  

Science Conference Proceedings (OSTI)

Aug 8, 2013 ... Tribological Characterizations of Ultrafine-Grained Alloys Processed by High Pressure Torsion: Nong Gao1; Chuan Ting Wang1; Wood ...

390

Fire safety for your wood-burning appliance: tips for proper installation, operation, and maintenance  

Science Conference Proceedings (OSTI)

A dramatic increase in house fires caused by wood-burning appliances has accompanied the rediscovery of wood as an alternative heating fuel. The National Bureau of Standards attributed the majority of these fires to conditions related to the installation, operation or maintenance of the appliances rather than malfunctions or construction defects. This publication presents guidelines for the proper installation, use, and maintenance of wood-burning appliances in the home. (DMC)

Not Available

1984-01-01T23:59:59.000Z

391

Options for Prevention, Mitigation, and Remediation at Wood Poles Storage Sites  

Science Conference Proceedings (OSTI)

As part of the maintenance of the electrical transmission and distribution networks in the United States, electric utilities store treated wood poles and cross arms at storage facilities. During this storage, chemicals of concern (COCs) used in preservative formulations can drip and leach during precipitation events from the treated wood poles and cross arms, potentially impacting site soils, groundwater, and nearby surface water bodies. These COCs will vary depending on the types of treated wood stored ...

2006-03-06T23:59:59.000Z

392

Modelling of mass transfer during wood fermentation processes to produce bioalcohol.  

E-Print Network (OSTI)

??The aim of this work is to model the bioethanol production by wood degradation, and to check if there is mass transfer limitations in the… (more)

Spalluto, Giorgio

2011-01-01T23:59:59.000Z

393

Microsoft Word - CX-CowlitzTaptoChehalis-CovingtonWoodPoles_WEB...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8, 2011 REPLY TO ATTN OF: KEPR-Covington SUBJECT: Environmental Clearance Memorandum Clay Grande Line Foreman III - TFCF-Covington Proposed Action: Wood pole replacement at...

394

Development of a Financial Model for Wood Pellet Production Costs in New England.  

E-Print Network (OSTI)

??The wood fuel pellet industry has been growing rapidly in recent years. The conversion of a significant proportion of central home heating systems in the… (more)

Lu, Ning

2012-01-01T23:59:59.000Z

395

Wood compost process engineering, properties and its impact on extreme soil characteristics.  

E-Print Network (OSTI)

??The landfilling of biodegradable waste is proven to contribute to environmental degradation. Much wood and lumber is discharged as waste from the cleared fields. These… (more)

Nada, Wael Mohamed Abdel-Rahman

2011-01-01T23:59:59.000Z

396

Planning and setup for the implementation of coal and wood co-fired boilers.  

E-Print Network (OSTI)

??Coal and wood co-fired boiler technology has been significantly advancing in the past years, but many of their capabilities remain unknown to much of the… (more)

Gump, Christopher D.

2007-01-01T23:59:59.000Z

397

Finding the light out of Into the Woods : a lighting design.  

E-Print Network (OSTI)

??Designing the lighting for any major theatrical production is comparable to one's own adventure through the woods. From pre-production to finalized design this thesis project… (more)

Groskopf, Kelli Jean

2012-01-01T23:59:59.000Z

398

Techno-economic analysis of wood biomass boilers for the greenhouse industry  

SciTech Connect

The objective of this study is to perform a techno-economic analysis on a typical wood pellet and wood residue boiler for generation of heat to an average-sized greenhouse in British Columbia. The variables analyzed included greenhouse size and structure, boiler efficiency, fuel types, and source of carbon dioxide (CO2) for crop fertilization. The net present value (NPV) show that installing a wood pellet or a wood residue boiler to provide 40% of the annual heat demand is more economical than using a natural gas boiler to provide all the heat at a discount rate of 10%. For an assumed lifespan of 25 years, a wood pellet boiler system could generate NPV of C$259,311 without electrostatic precipitator (ESP) and C$74,695 with ESP, respectively. While, installing a wood residue boiler with or without an ESP could provide NPV of C$919,922 or C$1,104,538, respectively. Using a wood biomass boiler could also eliminate over 3000 tonne CO2 equivalents of greenhouse gases annually. Wood biomass combustion generates more particulate matters than natural gas combustion. However, an advanced emission control system could significantly reduce particulate matters emission from wood biomass combustion which would bring the particulate emission to a relatively similar level as for natural gas.

Chau, J. [University of British Columbia, Vancouver; Sowlati, T. [University of British Columbia, Vancouver; Sokhansanj, Shahabaddine [ORNL; Bi, X.T. [University of British Columbia, Vancouver; Preto, F. [Natural Resources Canada; Melin, Staffan [University of British Columbia, Vancouver

2009-01-01T23:59:59.000Z

399

Particulate emissions from residential wood combustion: Final report: Norteast regional Biomass Program  

DOE Green Energy (OSTI)

The objective of this study was to provide a resource document for the Northeastern states when pursuing the analysis of localized problems resulting from residential wood combustion. Specific tasks performed include assigning emission rates for total suspended particulates (TSP) and benzo(a)pyrene (BaP) from wood burning stoves, estimating the impact on ambient air quality from residential wood combustion and elucidating the policy options available to Northeastern states in their effort to limit any detrimental effects resulting from residential wood combustion. Ancillary tasks included providing a comprehensive review on the relevant health effects, indoor air pollution and toxic air pollutant studies. 77 refs., 11 figs., 25 tabs.

Not Available

1987-01-01T23:59:59.000Z

400

Issues in the use of wood as an energy source in the northeastern US  

DOE Green Energy (OSTI)

This report analyzes some of the concerns surrounding the use of wood for energy in the Northeast. It reviews the information on resource availability and ownership patterns in the Northeast, then focuses on New England, to assess the affect of potential resource constraints on the supply of wood available for energy and the effects of wood energy use on land use patterns. Finally, the application of specific technologies in settings that may experience significant wood energy use in the future is considered, including an assessment of the regional employment and income benefits of a major woodfuel installation.

Munson, J.S. (ed.)

1980-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Rapid determination of wood fuel moisture content using a microwave oven for drying  

SciTech Connect

A method of determining moisture content (MC) of wood fuel using a microwave oven for drying the wood was evaluated by drying paired samples of five different wood fuel types in a microwave oven and a conventional oven. When compared to the conventional oven drying method, the microwave technique produces consistently lower MC determinations, although the differences are less than 1 percent. The advantage of the microwave technique is the speed at which MC determinations can be determined (less than 15 minutes). Schedules for drying five wood fuel types are presented. (Refs. 7).

Harris, R.A.

1982-10-01T23:59:59.000Z

402

Microsoft Word - CX-BigEddy-RedmondWoodPoles_WEB.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Clearance Memorandum Darrell Aaby Line Foreman III - TFDF-Redmond Proposed Action: Wood pole replacements at select locations along the Big Eddy-Redmond and Redmond-Pilot...

403

Advanced Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Materials Advanced Materials Availability Technology Express Licensing Active Terahertz Metamaterial Devices Express Licensing Anion-Conducting Polymer, Composition, And...

404

Wood-Coal Fired "Small" Boiler Case Study  

E-Print Network (OSTI)

Galaxy Carpet Corporation installed a coal and wood waste fired boiler approximately twelve months ago. Its first year net savings were $195,000.00 Total capital investment was paid off in 1.9 years. 20% investment tax credits were granted by the Federal Government. Galaxy Carpet Corporation has been sufficiently impressed with performance, both economically and technically, to place a follow-up order of $1,500,000.00 for a second solid fuel fired boiler system at its Dalton, Georgia Dye House operation.

Pincelli, R. D.

1980-01-01T23:59:59.000Z

405

Urban Wood-Based Bio-Energy Systems in Seattle  

DOE Green Energy (OSTI)

d.\tFuel Supply Management Plan: Development of plans and specifications for the supply of wood. It will include potential fuel sampling analysis and development of contracts for delivery and management of fuel suppliers and handlers. e.\tIntegrated Fuel Management System Development: Seattle Steam requires a biomass Fuel Management System to track and manage the delivery, testing, processing and invoicing of delivered fuel. This application will be web-based and accessed from a password-protected URL, restricting data access and privileges by user-level.

Stan Gent, Seattle Steam Company

2010-10-25T23:59:59.000Z

406

Materials Characterization | Advanced Materials | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

Characterization Nuclear Forensics Scanning Probes Related Research Materials Theory and Simulation Energy Frontier Research Centers Advanced Materials Home | Science &...

407

Enhanced Raw Materials Forest Products Environmental Influences on Wood Chemistry and Density of Populus and Loblolly  

E-Print Network (OSTI)

of Sterility in Forest Trees................................................................................................... 2

Hq Program Managers

2005-01-01T23:59:59.000Z

408

Environmental Influences on Wood Chemistry and Density of Populus and Loblolly Pine  

DOE Green Energy (OSTI)

The objectives of the study are to: (1) determine the degree to which physical and chemical wood properties vary in association with environmental and silvicultural practices in Populus and loblolly pine and (2) develop and verify species-specific empirical models in an effort to create a framework for understanding environmental influences on wood quality.

Tuskan, G.A.

2006-08-11T23:59:59.000Z

409

THE ROLE OF DEAD WOOD IN MAINTAINING ARTHROPOD DIVERSITY ON THE FOREST FLOOR.  

Science Conference Proceedings (OSTI)

Abstract—Dead wood is a major component of forests and contributes to overall diversity, primarily by supporting insects that feed directly on or in it. Further, a variety of organisms benefit by feeding on those insects. What is not well known is how or whether dead wood influences the composition of the arthropod community that is not solely dependent on it as a food resource, or whether woody debris influences prey available to generalist predators. One group likely to be affected by dead wood is ground-dwelling arthropods. We studied the effect of adding large dead wood to unburned and frequently burned pine stands to determine if dead wood was used more when the litter and understory plant community are removed. We also studied the effect of annual removal of dead wood from large (10-ha) plots over a 5-year period on ground-dwelling arthropods. In related studies, we examined the relationships among an endangered woodpecker that forages for prey on live trees, its prey, and dead wood in the forest. The results of these and other studies show that dead wood can influence the abundance and diversity of the ground-dwelling arthropod community and of prey available to generalist predators not foraging directly on dead trees.

Hanula, James L.; Horn, Scott; Wade, Dale D.

2006-08-01T23:59:59.000Z

410

Numerical and experimental validation of heat and mass transfer during heat treatment of wood  

Science Conference Proceedings (OSTI)

In the current work, the three-dimensional Navier-Stokes equations along with the energy and concentration equations for the fluid coupled with the energy and mass conservation equations for the solid (wood) are solved to study the transient heat and ... Keywords: Luikov's model, conjugate problem, heat and mass transfer, high-temperature wood treatment, mathematical modeling, validation

R. Younsi; D. Kocaefe; S. Poncsak; T. Junjun

2007-05-01T23:59:59.000Z

411

National Woodfuels and Wood Energy Information Analysis Prepared by: Sok Bun Heng  

E-Print Network (OSTI)

supplies. - 90 % of wood energy is consumed by households. - Industry is only a very small consumer of wood % Charcoal 1.2 %, other biomass 1.7 % and imported petroleum product. The most recent national energy supply balance indicates traditional fuels contribute 85 % of the national energy supply, of which 80

412

Wood Pellets for UBC Boilers Replacing Natural Gas Based on LCA  

E-Print Network (OSTI)

Wood Pellets for UBC Boilers Replacing Natural Gas Based on LCA Submitted to Dr. Bi By Bernard Chan Pellets for UBC Boilers Replacing Natural Gas" By Bernard Chan, Brian Chan, and Christopher Young Abstract This report studies the feasibility of replacing natural gas with wood pellets for UBC boilers. A gasification

413

Design of an automatic wood types classification system by using fluorescence spectra  

Science Conference Proceedings (OSTI)

The classification of wood types is needed in many industrial sectors, since it can provide relevant information concerning the features and characteristics of the final product (appearance, cost,mechanical properties, etc.). This analysis is typical ... Keywords: automatic spectra analysis, automatic wood classification, computational intelligence

Vincenzo Piuri; Fabio Scotti

2010-05-01T23:59:59.000Z

414

Relationships between dead wood and arthropods in the Southeastern United States.  

SciTech Connect

The importance of dead wood to maintaining forest diversity is now widely recognized. However, the habitat associations and sensitivities of many species associated with dead wood remain unknown, making it difficult to develop conservation plans for managed forests. The purpose of this research, conducted on the upper coastal plain of South Carolina, was to better understand the relationships between dead wood and arthropods in the southeastern United States. In a comparison of forest types, more beetle species emerged from logs collected in upland pine-dominated stands than in bottomland hardwood forests. This difference was most pronounced for Quercus nigra L., a species of tree uncommon in upland forests. In a comparison of wood postures, more beetle species emerged from logs than from snags, but a number of species appear to be dependent on snags including several canopy specialists. In a study of saproxylic beetle succession, species richness peaked within the first year of death and declined steadily thereafter. However, a number of species appear to be dependent on highly decayed logs, underscoring the importance of protecting wood at all stages of decay. In a study comparing litter-dwelling arthropod abundance at different distances from dead wood, arthropods were more abundant near dead wood than away from it. In another study, grounddwelling arthropods and saproxylic beetles were little affected by large-scale manipulations of dead wood in upland pine-dominated forests, possibly due to the suitability of the forests surrounding the plots.

Ulyshen, Michael, Darragh

2009-05-01T23:59:59.000Z

415

Characterization and explanation of the sustainability of the European wood manufacturing industries: A quantitative approach  

Science Conference Proceedings (OSTI)

This paper has a twofold purpose. First, to characterize the sustainability of the European wood manufacturing industry. In this way, a ranking of the European countries analyzed in terms of sustainability is established. To undertake this task the sustainability ... Keywords: Econometric models, Goal programming, Indicators, Sustainability, Wood manufacturing industry

Roberto Voces; Luis Diaz-Balteiro; Carlos Romero

2012-06-01T23:59:59.000Z

416

Creosote-Treated Wood Poles and Crossarms: Toxicity Characteristic Leaching Procedure (TCLP) Results  

Science Conference Proceedings (OSTI)

If creosote-treated wood poles and crossarms are classified as hazardous waste by the EPA's revised toxicity characteristic rule, disposal costs will rise dramatically. However, when the rule is applied to data obtained from this EPRI study, creosote-treated utility wood poles and crossarms receive a nonhazardous classification.

1992-08-06T23:59:59.000Z

417

Pentachlorophenol (PCP)-Treated Wood Poles and Crossarms: Toxicity Characteristic Leaching Procedure (TCLP) Results  

Science Conference Proceedings (OSTI)

If pentachlorophenol (PCP)-treated wood poles and crossarms are classified as hazardous waste by the revised toxicity characteristic (TC) rule, disposal costs will rise dramatically. However, when the ruling is applied to data obtained during this study, PCP-treated utility wood poles and crossarms receive a nonhazardous classification.

1991-01-03T23:59:59.000Z

418

Seismic design of a current woodframe structure and study of innovative products and damping systems in wood construction  

E-Print Network (OSTI)

Wood structures have seen resurgence in popularity over the past several decades, especially in Western States of America, such as California. The industry keeps creating new structural wood products of exceptional strength, ...

Mahjoub, Nina A. (Nina Azadeh)

2007-01-01T23:59:59.000Z

419

Materials Science  

NLE Websites -- All DOE Office Websites (Extended Search)

Materials Science Materials Science Materials Science1354608000000Materials ScienceSome of these resources are LANL-only and will require Remote Access./No/Questions? 667-5809library@lanl.gov Materials Science Some of these resources are LANL-only and will require Remote Access. Key Resources Data Sources Reference Organizations Journals Key Resources CINDAS Materials Property Databases video icon Thermophysical Properties of Matter Database (TPMD) Aerospace Structural Metals Database (ASMD) Damage Tolerant Design Handbook (DTDH) Microelectronics Packaging Materials Database (MPMD) Structural Alloys Handbook (SAH) Proquest Technology Collection Includes the Materials Science collection MRS Online Proceedings Library Papers presented at meetings of the Materials Research Society Data Sources

420

Reactor Materials  

Energy.gov (U.S. Department of Energy (DOE))

The reactor materials crosscut effort will enable the development of innovative and revolutionary materials and provide broad-based, modern materials science that will benefit all four DOE-NE...

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Woodfuel Usage Update 1 I Wood fuel use in Scotland 2011 I Hudson Consulting I September 2011  

E-Print Network (OSTI)

Recycled fibre Energy crops, forest residues and tree stumps The first reports on wood fuel usage data hadWoodfuel Usage Update 1 I Wood fuel use in Scotland 2011 I Hudson Consulting I September 2011 Woodfuel Demand and Usage in Scotland Report 2011 #12;Woodfuel Usage Update 2 I Wood fuel use in Scotland

422

Materials - Assessment  

NLE Websites -- All DOE Office Websites (Extended Search)

Materials Assessment The staff of the Energy Systems Division has a long history of technical and economic analysis of the production and recycling of materials for transportation...

423

Materials Science  

NLE Websites -- All DOE Office Websites (Extended Search)

Materials Science science-innovationassetsimagesicon-science.jpg Materials Science National security depends on science and technology. The United States relies on Los Alamos...

424

Conversion of cellulose materials into nanostructured ceramics by biomineralization  

DOE Green Energy (OSTI)

Synthesis of hierarchically ordered silica materials having ordered wood cellular structures has been demonstrated through in-situ mineralization of wood by means of surfactant-directed mineralization in solutions of different pH. At low pH, silicic acid penetrates the buried interfaces of the wood cellular structure without clogging the pores to subsequently “molecularly paint” the interfaces thereby forming a positive replica following calcinations. At high pH, the hydrolyzed silica rapidly condenses to fill the open cells and pits within the structure resulting in a negative replica of the structure. Surfactant-templated mineralization in acid solutions leads to the formation of micelles that hexagonally pack at the wood interfaces preserving structural integrity while integrating hexagonally ordered nanoporosity into the structure of the cell walls following thermal treatment in air. The carbothermal reduction of mineralized wood with silica at high temperature produces biomorphic silicon carbide (SiC) materials, which are typical aggregations of ?-SiC nanoparticles. To understand the roles of each component (lignin, crystalline cellulose, amorphous cellulose) comprising the natural biotemplates in the transformation to SiC rods, three different cellulose precursors including unbleached and bleached pulp, and cellulose nanocrystals have been utilized. Lignin in unbleached pulp blocked homogeneous penetration of silica into the pores between cellulose fibers resulting in non-uniform SiC fibers containing thick silica layers. Bleached pulp produced uniform SiC rods with camelback structures (80nm in diameter; ~50?m in length), indicating that more silica infiltrates into the amorphous constituent of cellulose to form chunky rather than straight rod structures. The cellulose nanocrystal (CNXL) material produced clean and uniform SiC nanowires (70nm in diameter; >100?m in length) without the camelback structure.

Shin, Yongsoon; Exarhos, Gregory J.

2007-06-01T23:59:59.000Z

425

Warren T. Wood, L. Dale Bibee, Edward F. Braithwaite Introduction  

NLE Websites -- All DOE Office Websites (Extended Search)

Deployment of a Deep-water Seafloor Sound Source Deployment of a Deep-water Seafloor Sound Source Warren T. Wood, L. Dale Bibee, Edward F. Braithwaite Introduction With funding from DOE-NETL, the Naval Research Laboratory's deep-towed acoustic geophysics system (DTAGS) was outfitted to be set directly on the seafloor with the intent of more efficiently generating shear wave energy in the seafloor. We altered the existing DTAGS by adding a releasable landing shoe, and a geophone array that used existing data telemetry. The modified system was deployed in March of 2010 in about 900m of water near the site of the University of Mississippi's gas hydrate observatory in lease block

426

The Honorable John T. 'Gregorio 301 N. Wood Avenue  

Office of Legacy Management (LM)

Eiergy ; Eiergy ; Washington, DC 20585 -, (, > - .' c ' . FEB 1 7 1995 _ .; , _-, The Honorable John T. 'Gregorio 301 N. Wood Avenue Linden, 'New Jersey 07036 d. \ Dear Mayor Gregorio: ,' ,' .' , Secretary of Energy Hazel O'Leary has announced a new approach to openness, in the'llepartment' of Energy (DDE) and its co,annunications with the .public.', In sup~port of this initiative, we are.pleased to forward.the,enclosed information reiated to the.former Linden Pilot Plant of the Chemical' Construction Company in your jurisdiction that performed work for DOE's.predecessor agencies. This information is provided for your information, use,.and reten,tion. '. , / DOE's Formerly Utilized Sites Remedial Action Program is responsible for identification of sites used by DOE's predecessor agencies, determining their

427

Water Sampling At International Geothermal Area, Philippines (Wood, 2002) |  

Open Energy Info (EERE)

Water Sampling At International Geothermal Area Water Sampling At International Geothermal Area Philippines (Wood, 2002) Exploration Activity Details Location International Geothermal Area Philippines Exploration Technique Water Sampling Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes Geothermal fluids from hot springs and wells have been sampled from a number of locations, including: 1) the North Island of New Zealand (three sets of samples from three different years) and the South Island of New Zealand (1 set of samples); 2) the Cascades of Oregon; 3) the Harney, Alvord Desert and Owyhee geothermal areas of Oregon; 4) the Dixie Valley and Beowawe fields in Nevada; 5) Palinpiiion, the Philippines; 6) the Salton Sea and Heber geothermal fields of southern California; and 7) the

428

Microsoft Word - CX-Murray-CusterWoodPoles_WEB.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Covington Covington SUBJECT: Environmental Clearance Memorandum Steve Scott Line Foreman III - TFNF-Snohomish Proposed Action: Wood pole replacement at selected locations along the Murray-Custer #1 transmission line right-of-way (ROW). PP&A Project No.: 1963 Categorical Exclusion Applied (from Subpart D, 10 C.F.R. Part 1021): B1.3 Routine maintenance activities...for structures, rights-of-way, infrastructures such as roads, equipment... routine maintenance activities, corrective...are required to maintain...infrastructures...in a condition suitable for a facility to be used for its designed purpose. Location: The proposed project is located in Snohomish and Skagit Counties, Washington, in Bonneville Power Administration's (BPA) Snohomish District.

429

Compound and Elemental Analysis At Breitenbush Hot Springs Area (Wood,  

Open Energy Info (EERE)

2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Compound and Elemental Analysis At Breitenbush Hot Springs Area (Wood, 2002) Exploration Activity Details Location Breitenbush Hot Springs Area Exploration Technique Compound and Elemental Analysis Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes Geothermal fluids from hot springs and wells have been sampled from a number of locations, including: 1) the North Island of New Zealand (three sets of samples from three different years) and the South Island of New Zealand (1 set of samples); 2) the Cascades of Oregon; 3) the Harney, Alvord Desert and Owyhee geothermal areas of Oregon; 4) the Dixie Valley and Beowawe fields in Nevada; 5) Palinpiiion, the Philippines; 6) the

430

Fusion-fission reactions with modified Woods-Saxon potential  

E-Print Network (OSTI)

A modified Woods-Saxon potential model is proposed for a unified description of the entrance channel fusion barrier and the fission barrier of fusion-fission reactions based on the Skyrme energy-density functional approach. The fusion excitation functions of 120 reactions have been systematically studied. The fusion (capture) cross sections are well described with the calculated potential and an empirical barrier distribution. Incorporating a statistical model (HIVAP code) for describing the decay of the compound nucleus, the evaporation residue (and fission) cross sections of 51 fusion-fission reactions have been systematically investigated. Optimal values of some key parameters of the HIVAP code are obtained based on the experimental data of these reactions. The experimental data are reasonably well reproduced by the calculated results. The upper and lower confidence limits of the systematic errors of the calculated results are given.

Ning Wang; Kai Zhao; Werner Scheid; Xizhen Wu

2007-12-15T23:59:59.000Z

431

Thermoelectric Materials  

Science Conference Proceedings (OSTI)

Thermoelectric materials can generate electricity or provide cooling by converting thermal gradients to electricity or electricity to thermal gradients. More efficient thermoelectric materials would make feasible the widespread use of thermoelectric converters in mundane applications. This report summarizes the state-of-the-art of thermoelectric materials including currently available materials and applications, new developments, and future prospects.

2000-01-14T23:59:59.000Z

432

Kinetic Modeling and Assessment of Lime Pretreatment of Poplar Wood  

E-Print Network (OSTI)

Because of widespread availability, low cost, sustainability, and potential supply far greater than that of food crops, lignocellulosic biomass is one of the most promising feedstocks for producing biofuels through fermentation processes. Among lignocellulose choices, poplar wood is appealing because of high energy potential, above-average carbon mitigation potential, fast growth, and high yields. Lignocellulose structural features limit accessibility of enzymes or microorganisms. To overcome these limitations, pretreatment is required. Among several choices of pretreatment, lime pretreatment is preferred because lime is the cheapest alkali, safest to handle, easy to recover, and compatible with oxidants. The main effect of lime pretreatment is to degrade lignin, which occurs with good carbohydrate preservation and is enhanced with oxidants. Among several choices of oxidant, oxygen and air are preferred because of low cost and widespread availability. This study systematically assesses the effects of lime pretreatment on poplar wood using four different modes: long-term oxidative, long-term non-oxidative, short-term constant pressure, and short-term varying pressure. Long-term pretreatments use temperatures between 25 and 65° C, air if oxidant is used, and last several weeks. Short-term pretreatments use temperatures between 110 and 180° C, pressurized oxygen, and last several minutes to hours. Pretreatment was assessed on the basis of 3-day enzymatic digestibility using enzyme loadings of 15 FPU/g glucan in raw biomass. The results were used to recommend pretreatment conditions based on highest overall yield of glucan (after combined pretreatment and enzymatic hydrolysis) for each pretreatment mode. For each pretreatment mode, kinetic models for delignification and carbohydrates degradation were obtained and used to determine the conditions (temperature, pressure, and time) that maximize glucan preservation subjected to a target lignin yield. This study led to conclude that the most robust, and selective mode of lime pretreatment is varying pressure.

Sierra Ramirez, Rocio

2010-12-01T23:59:59.000Z

433

Urban Wood-Based Bio-Energy Systems in Seattle  

SciTech Connect

Seattle Steam Company provides thermal energy service (steam) to the majority of buildings and facilities in downtown Seattle, including major hospitals (Swedish and Virginia Mason) and The Northwest (Level I) Regional Trauma Center. Seattle Steam has been heating downtown businesses for 117 years, with an average length of service to its customers of 40 years. In 2008 and 2009 Seattle Steam developed a biomass-fueled renewable energy (bio-energy) system to replace one of its gas-fired boilers that will reduce greenhouse gases, pollutants and the amount of waste sent to landfills. This work in this sub-project included several distinct tasks associated with the biomass project development as follows: a. Engineering and Architecture: Engineering focused on development of system control strategies, development of manuals for start up and commissioning. b. Training: The project developer will train its current operating staff to operate equipment and facilities. c. Flue Gas Clean-Up Equipment Concept Design: The concept development of acid gas emissions control system strategies associated with the supply wood to the project. d. Fuel Supply Management Plan: Development of plans and specifications for the supply of wood. It will include potential fuel sampling analysis and development of contracts for delivery and management of fuel suppliers and handlers. e. Integrated Fuel Management System Development: Seattle Steam requires a biomass Fuel Management System to track and manage the delivery, testing, processing and invoicing of delivered fuel. This application will be web-based and accessed from a password-protected URL, restricting data access and privileges by user-level.

Stan Gent, Seattle Steam Company

2010-10-25T23:59:59.000Z

434

Air emissions from residential heating: The wood heating option put into environmental perspective. Report for June 1997--July 1998  

SciTech Connect

The paper compares the national scale (rather than local) air quality impacts of the various residential space heating options. Specifically, it compares the relative contributions of the space heating options to fine particulate emissions, greenhouse gas emissions, and acid precipitation impacts. The major space heating energy options are natural gas, fuel oil, kerosene, liquefied petroleum gas (LPG), electricity, coal, and wood. Residential wood combustion (RWC) meets 9% of the Nation`s space heating energy needs and utilizes a renewable resource. Wood is burned regularly in about 30 million homes. Residential wood combustion is often perceived as environmentally dirty due to emissions from older wood burners.

Houck, J.E.; Tiegs, P.E.; McCrillis, R.C.; Keithley, C.; Crouch, J.

1998-12-31T23:59:59.000Z

435

Economic impacts of wood energy in the Northeast, 1985: Summary report: Northeast Regional Biomass Program  

DOE Green Energy (OSTI)

Wood energy in the Northeast accounts for an estimated average of 1.96 jobs and $46,634 of income for every 1000 tons of wood burned by households and businesses. This translates into an estimated total of over 78,000 jobs and $1.8 billion of personal income for Northeast residents and businesses. In addition, a total of $589 million in state and federal tax revenues are generated by wood energy-related economic activity. By choosing wood over other fuels, Northeast households and businesses saved $1.2 billion in their 1985 fuel bills. In the Northeast in 1985, wood displaced over 1 billion gallons of oil, 37 million tcf of natural gas and propane, 138,000 tons of coal, and 1858 million kilowatt-hours of electricity. Projected growth in wood energy consumption in the industrial and residential sectors indicate that the Northeast wood energy industry will support approximately 165,000 jobs and $3.8 billion of personal and business income by the year 2000, if projected growth continues. 9 figs., 5 tabs.

Chamberlin, R.; High, C.

1986-04-01T23:59:59.000Z

436

Comparative Sugar Recovery and Fermentation Data Following Pretreatment of Poplar Wood by Leading Technologies  

SciTech Connect

Through a Biomass Refining Consortium for Applied Fundamentals and Innovation among Auburn University, Dartmouth College, Michigan State University, the National Renewable Energy Laboratory, Purdue University, Texas A&M University, the University of British Columbia, and the University of California at Riverside, leading pretreatment technologies based on ammonia fiber expansion, aqueous ammonia recycle, dilute sulfuric acid, lime, neutral pH, and sulfur dioxide were applied to a single source of poplar wood, and the remaining solids from each technology were hydrolyzed to sugars using the same enzymes. Identical analytical methods and a consistent material balance methodology were employed to develop comparative performance data for each combination of pretreatment and enzymes. Overall, compared to data with corn stover employed previously, the results showed that poplar was more recalcitrant to conversion to sugars and that sugar yields from the combined operations of pretreatment and enzymatic hydrolysis varied more among pretreatments. However, application of more severe pretreatment conditions gave good yields from sulfur dioxide and lime, and a recombinant yeast strain fermented the mixed stream of glucose and xylose sugars released by enzymatic hydrolysis of water washed solids from all pretreatments to ethanol with similarly high yields. An Agricultural and Industrial Advisory Board followed progress and helped steer the research to meet scientific and commercial needs.

Wyman, C. E.; Dale, B. E.; Elander, R. T.; Holtzapple, M.; Ladisch, M. R.; Lee, Y. Y.; Mitchinson, C.; Saddler, J. N.

2009-01-01T23:59:59.000Z

437

PSNH's Northern Wood power project repowers coal-fired plant with new fluidized-bed combustor  

SciTech Connect

The Northern Wood Power project permanently replaced a 50-MW coal-burning boiler (Unit 5) at Public Service of New Hampshire's Schiller station with a state-of-the-art circulating fluidized bed wood-burning boiler of the same capacity. The project, completed in December 2006, reduced emissions and expanded the local market for low-grade wood. For planning and executing the multiyear, $75 million project at no cost to its ratepayers, PSNH wins Power's 2007 Marmaduke Award for excellence in O & M. The award is named for Marmaduke Surfaceblow, the fictional marine engineer/plant troubleshoot par excellence. 7 figs., 1 tab.

Peltier, R.

2007-08-15T23:59:59.000Z

438

Continuous On-Line Measurement of Lignin Concentration in Wood Pulp  

E-Print Network (OSTI)

We are working toward the development of an instrument for the continuous, on-line measurement of the lignin concentration in wood pulp. The instrument is based on laser induced fluorescence of the wood pulp and is to be used as a primary sensor for both feedback control of the pulping and feedforward control of bleaching. We report here the results of a series of laboratory tests that characterized the fluorescence properties of wood pulp and demonstrated a correlation between various fluorescence functions and the Kappa number of the pulps as determined by TAPPI Procedure T236.

Jeffers, L. A.; Roman, G. W.

1994-04-01T23:59:59.000Z

439

Feasibility study of wood-fired cogeneration at a Wood Products Industrial Park, Belington, WV. Phase II  

DOE Green Energy (OSTI)

Customarily, electricity is generated in a utility power plant while thermal energy is generated in a heating/cooling plant; the electricity produced at the power plant is transmitted to the heating/cooling plant to power equipments. These two separate systems waste vast amounts of heat and result in individual efficiencies of about 35%. Cogeneration is the sequential production of power (electrical or mechanical) and thermal energy (process steam, hot/chilled water) from a single power source; the reject heat of one process issued as input into the subsequent process. Cogeneration increases the efficiency of these stand-alone systems by producing these two products sequentially at one location using a small additional amount of fuel, rendering the system efficiency greater than 70%. This report discusses cogeneration technologies as applied to wood fuel fired system.

Vasenda, S.K.; Hassler, C.C.

1992-06-01T23:59:59.000Z

440

Method for distributing chemicals through a fibrous material using low-headspace dielectric heating  

DOE Patents (OSTI)

System and method for diffusing chemicals rapidly and evenly into and through fibrous material, such as wood. Chemicals are introduced into the fibrous material by applying the chemicals to the fibrous material. After treating the fibrous material with the chemicals, the fibrous material is maintained under low-headspace conditions. Thermal energy or dielectric heating, such as microwave or radio frequency energy, is applied to the fibrous material. As a result, the chemicals are able to distribute evenly and quickly throughout the fibrous material.

Banerjee, Sujit (Marietta, GA); Malcolm, Earl (Bluffton, SC)

2002-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Cellular Materials in Nature  

Science Conference Proceedings (OSTI)

Wood and cork have a honeycomb-like structure with cells that are roughly hexagonal ... Influence of Heating of Al2O3 Particle with Holding Time Variation to ...

442

Magnetocaloric Materials  

Science Conference Proceedings (OSTI)

Magnetic Materials for Energy Applications IV: Magnetocaloric Materials ... due to cost-effectiveness as well as superior magneto-thermal characteristics. ... metals and p-block elements can be explored in a time- and energy-saving manner.

443

Materials Science  

Science Conference Proceedings (OSTI)

Materials Science. Summary: Key metrologies/systems: In situ spectroscopic ellipsometry, linear and non-linear spectroscopies ...

2012-10-02T23:59:59.000Z

444

Training Materials  

Science Conference Proceedings (OSTI)

Training Materials. NIST Handbook 44 Self-Study Course. ... Chapter 3 – Organization and Format of NIST Handbook 44 DOC. ...

2011-08-10T23:59:59.000Z

445

Digestive enzyme activities and gastrointestinal fermentation in wood-eating catfishes  

E-Print Network (OSTI)

the neotropical suckermouth armored catWshes (Siluriformes,T (2009) Non-native suckermouth armored catWshes in Florida:Loricariidae), wood-eating armored catWshes from tropical

German, Donovan P.; Bittong, Rosalie A.

2009-01-01T23:59:59.000Z

446

Health effects of residential wood combustion: survey of knowledge and research  

DOE Green Energy (OSTI)

Health and safety issues related to residential wood burning are examined. Current research and findings are also described, and research status is assessed in terms of future health and safety requirements. (MHR)

None

1980-09-01T23:59:59.000Z

447

Technical Viability of Biocoke from Mixtures Coal-Wood Charcoal for ...  

Science Conference Proceedings (OSTI)

The purpose of this paper is to replace from 10% to 50% of the coal used in cokemaking by mixing it with a renewable source (wood charcoal). The powder ...

448

Thermal properties of structural details in wood frame homes : analysis and recommendations  

E-Print Network (OSTI)

The wood platform frame home is the dominant design in the United States when it comes to single family housing. Introduced during the mid-nineteenth century, the scheme is a cheap, fast, and proven design that takes ...

Graybeal, Alexander Kung

2010-01-01T23:59:59.000Z

449

Global Trade of Wood and Paper Products Analysis by: Dr. Ed K. Pepke  

E-Print Network (OSTI)

of wood products, such as the United States, have become major net importers. Conversely, China, a country renewable energy sources in light of escalating fossil fuel prices, have created new international trade

450

Lowell L. Wood, 1981 | U.S. DOE Office of Science (SC)  

Office of Science (SC) Website

Lowell L. Wood, 1981 The Ernest Orlando Lawrence Award Lawrence Award Home Nomination & Selection Guidelines Award Laureates 2000's 1990's 1980's 1970's 1960's Ceremony The Life of...

451

SIDA DemoEast programme in Estonia. Supply, delivery and installation of wood pellet burning equipment  

E-Print Network (OSTI)

burning equipment SUMMARY DemoEast programme is a part of Baltic Billion Fund 2 with the overall aim and Kiltsi light oil fired boilers have been converted to wood pellets burning. The supplier

452

Microsoft Word - CX-Driscoll-NaselleWood PolesFY12_WEB.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Memorandum Ryan Brady Line Foreman III - TFOK-Chehalis Proposed Action: In-kind wood pole replacements as needed on the Driscoll-Naselle No. 1 115-kV transmission line...

453

Residential Bulk-Fed Wood-Pellet Central Boilers and Furnace Rebate Program  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Residential Bulk-Fed Wood-Pellet Central Boilers and Furnace Rebate Residential Bulk-Fed Wood-Pellet Central Boilers and Furnace Rebate Program Residential Bulk-Fed Wood-Pellet Central Boilers and Furnace Rebate Program < Back Eligibility Multi-Family Residential Residential Savings Category Heating & Cooling Commercial Heating & Cooling Heating Maximum Rebate $6,000 Program Info Funding Source New Hampshire Renewable Energy Fund (FY 2013) Start Date 04/14/2010 Expiration Date When progr State New Hampshire Program Type State Rebate Program Rebate Amount 30% Provider New Hampshire Public Utilities Commission The New Hampshire Public Utilities Commission (PUC) is offering rebates of 30% of the installed cost of qualifying new residential bulk-fed, wood-pellet central heating boilers or furnaces. The maximum rebate is $6,000. To qualify, systems must (1) become operational on or after May 1,

454

Material matting  

Science Conference Proceedings (OSTI)

Despite the widespread use of measured real-world materials, intuitive tools for editing measured reflectance datasets are still lacking. We present a solution inspired by natural image matting and texture synthesis to the material matting problem, ... Keywords: appearance models, material separation, matting, spatially-varying BRDFs, texture synthesis

Daniel Lepage; Jason Lawrence

2011-12-01T23:59:59.000Z

455

Materializing energy  

Science Conference Proceedings (OSTI)

Motivated and informed by perspectives on sustainability and design, this paper draws on a diverse body of scholarly works related to energy and materiality to articulate a perspective on energy-as-materiality and propose a design approach of ... Keywords: design, design theory, energy, materiality, sustainability

James Pierce; Eric Paulos

2010-08-01T23:59:59.000Z

456

Synthesis of SiC ceramics by the carbothermal reduction of mineralized wood with silica  

DOE Green Energy (OSTI)

This paper describes the synthesis of SiC by the carbothermal reduction of mineralized wood with silica in acidic condition. The biomorphic cellular SiC ceramics were prepared by controlling the amount of silica and the size of SiC nanoparticles. Up to 20wt% of SiO2 was mineralized into wood cellular structures and the hierarchical structures such as cells, lumen, and pits were mainly retained after the thermal treatment at 1400 C.

Shin, Yongsoon; Wang, Chong M.; Exarhos, Gregory J.

2005-01-06T23:59:59.000Z

457

Variations in the Hygrothermal Properties of Several Wood-Based Building Products  

E-Print Network (OSTI)

A systematic investigation of the hygrothermal properties of a number of oriented strand boards, plywood products, wood fibreboards and composite wood sidings has resulted in new information on the variations of thermal conductivity, water vapour permeability, moisture diffusivity, sorption- desorption -suction isotherms, water absorption coefficient and air permeability of these classes of products in North America. The experimental and analytical procedures used in the investigation are all based either on International Standards or on well-documented and peer-reviewed approaches.

J.C. Lackey; N. Normandin; D. van Reenen; M. K. Kumaran; J. C. Lackey; N. Norm; F. Tariku; D. Van Reenen

2003-01-01T23:59:59.000Z

458

Smoke and toxic species analyses from controlled combustion of wood impregnated with guayule resin  

E-Print Network (OSTI)

Dominant commercial treatments currently used for wood preservation are pentachlorophenols (PCP), creosote, and chromium copper arsenicals. These wood preservatives present many studied and documented environmental and toxicological problems with both use of the products themselves, and with the production of secondary reaction contaminants. Furthermore, several of these preservatives are considered priority pollutants according to the U. S. Environmental Protection Agency and are heavily regulated. The need for an environmentally benign combined fire/rot retardant treatment for wood that will effectively reduce both fire and decay is clearly evident. Guayule resin, a co-by-product during rubber extraction from the guayule shrub, is being explored by us as a natural, biodegradable wood rot and fire retardant with potential commercial applications. Wood impregnated with guayule resin has survived over eight years in tropical soils, free of rot, decay, and insect infestations. This study qualitatively analyzed the treated and untreated wood samples for ignitability, flame spread, toxic fumes, and smoke generation. Ignitability of the wood sample of fixed geometry was quantified by measuring the time required for ignition of treated samples vs. untreated samples. Flame spread was measured after ignition with a propane flame by a simple stopwatch-ruler technique. Smoke mass was determined in an Arapahoe Smoke Chamber as per ASTM D-4100. Analysis of the fumes involved continuous CO, C02, NOx, SOx, and 02 analyses using the Bacharach Instrument Model 300. Cascade impaction was used to determine the particle size distribution of the smoke and for smoke mass determination. Respirable particles were assessed by utilizing the Anderson 2000 Inc. 1 AFCM Ambient Particle Fractionating Sampler. Inflections of guayule-impregnated and untreated pine are indeed minor with respect to all aspects investigated. Ignition data indicated guayule-impregnated pine did not ignite as quickly as untreated pine. Evidence conveys favorable consideration for further research of wood preservation with guayule resin.

Smith, Lonnie

1995-01-01T23:59:59.000Z

459

Oxidation of volatiles in residential wood burning equipment. Final technical report, September 1980-February 1984  

DOE Green Energy (OSTI)

The objectives of this project are to measure, through the use of laboratory combustors, those conditions which promote complete combustion of wood volatiles in residential wood burning equipment. The conditions of interest are combustion temperature, residence time, stoichiometry, and air mixing. The project objectives are met through two laboratory approaches: (1) model compound studies: in order to measure the overall rates of oxidative pyrolysis of biomass volatiles, and to determine the types of intermediate organic species which are likely to form as part of this process, model compounds have been reacted in a specialized jet-stirred reactor, which has been developed as part of this research. (2) high-intensity wood combustion: in order to study the clean combustion of wood, that is, to investigate the conceptual design features required for clean burning, and to ascertain the levels and types of pollutant and condensible species which are most difficult to oxidize, a high-intensity, research wood combustor has been developed and examined for the different phases of the wood burning cycle. Although the objectives of the project have been met, it has not been possible, because of support limitations, to thoroughly explore several interesting aspects which have arisen because of this research. For example, a third laboratory system in which wood pyrolysis gas is injected directly into the a well characterized reactor, so that the kinetics and mechanisms of the gas-phase reaction of the actual biomass volatiles can be studied, could not be thoroughly developed. Refinements in the high-intensity wood combustor, which would bring its design features closer to practicality for the industry, could not be considered. 32 references, 37 figures, 10 tables.

Malte, P.C.; Thornton, M.M.; Kamber, P.D.

1984-04-01T23:59:59.000Z

460

New Solid Supported Precious Metal Catalysts on Cabonized Wood  

Science Conference Proceedings (OSTI)

Hybrid Aerogel/Nanorod Functional Materials for Energy and Sensing ... Processing and Characterization of Inorganic, High Temperature Nanomaterial Filter.

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Materials Education Community  

Science Conference Proceedings (OSTI)

Digital Resource Center Home. Materials Education. Materials Education. Established Materials Technologies. Magnesium · Superalloys. Emerging Materials ...

462

Emerging Materials Technologies  

Science Conference Proceedings (OSTI)

Digital Resource Center Home. Materials Education. Materials Education. Established Materials Technologies. Magnesium · Superalloys. Emerging Materials ...

463

Established Materials Technologies  

Science Conference Proceedings (OSTI)

Digital Resource Center Home. Materials Education. Materials Education. Established Materials Technologies. Magnesium · Superalloys. Emerging Materials ...

464

Wood Residues as Fuel Source for Lime Kilns  

E-Print Network (OSTI)

One of the main obstacles to total energy self sufficiency of kraft mills appears to be the fossil fuel requirements of the lime kilns. If an economical technology can be developed which allows fossil fuel to be replaced in whole or in part by wood-based fuel, the savings in fossil fuel by the pulp and paper industry would be very substantial. Our study focuses around the direct in-situ combustion of hog fuel fed from the cold feed end in order to substantially reduce the fossil fuel fired from the hot product discharge end of the lime kiln. Thus far we have carried out two series of tests using two different pilot-scale kilns and dry limestone in the first test series and mill produced lime mud in the second test series. Mill scale trials have just been completed and the preliminary results indicate that our approach is potentially a very cost-effective and simple option to substantially reduce or possibly eliminate fossil-fuel usage in lime kilns.

Azarniouch, M. K.; Philp, R. J.

1984-01-01T23:59:59.000Z

465

Minor Materials  

Science Conference Proceedings (OSTI)

Table 1   Materials used in glass manufacture...Table 1 Materials used in glass manufacture Material Purpose Antimony oxide (Sb 2 O 3 ) Decolorizing and fining agent Aplite (K, Na, Ca, Mg, alumina silicate) Source of alumina Aragonite (CaCO 3 ) Source of calcium oxide Arsenic oxide (As 2 O 3 ) Fining and decolorizing agent Barite/barytes (BaSO 4 )...

466

Scintillator material  

DOE Patents (OSTI)

An improved scintillator material comprising cerium fluoride is disclosed. Cerium fluoride has been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to known scintillator materials such as thallium-doped sodium iodide, barium fluoride and bismuth germanate. As a result, cerium fluoride is favorably suited for use as a scintillator material in positron emission tomography.

Anderson, David F. (Batavia, IL); Kross, Brian J. (Aurora, IL)

1992-01-01T23:59:59.000Z

467

Scintillator material  

DOE Patents (OSTI)

An improved scintillator material comprising cerium fluoride is disclosed. Cerium fluoride has been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to known scintillator materials such as thallium-doped sodium iodide, barium fluoride and bismuth germanate. As a result, cerium fluoride is favorably suited for use as a scintillator material in positron emission tomography. 4 figs.

Anderson, D.F.; Kross, B.J.

1994-06-07T23:59:59.000Z

468

Scintillator material  

DOE Patents (OSTI)

An improved scintillator material comprising cerium fluoride is disclosed. Cerium fluoride has been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to known scintillator materials such as thallium-doped sodium iodide, barium fluoride and bismuth germanate. As a result, cerium fluoride is favorably suited for use as a scintillator material in positron emission tomography. 4 figs.

Anderson, D.F.; Kross, B.J.

1992-07-28T23:59:59.000Z

469

Scintillator material  

DOE Patents (OSTI)

An improved scintillator material comprising cerium fluoride is disclosed. Cerium fluoride has been found to provide a balance of good stopping power, high light yield and short decay constant that is superior to known scintillator materials such as thallium-doped sodium iodide, barium fluoride and bismuth germanate. As a result, cerium fluoride is favorably suited for use as a scintillator material in positron emission tomography.

Anderson, David F. (Batavia, IL); Kross, Brian J. (Aurora, IL)

1994-01-01T23:59:59.000Z

470

Advanced Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Materials Advanced Materials Advanced Materials Express Licensing Active Terahertz Metamaterial Devices Express Licensing Anion-Conducting Polymer, Composition, And Membrane Express Licensing Analysis Of Macromolecule, Liggands And Macromolecule-Lingand Complexes Express Licensing Carbon Microtubes Express Licensing Chemical Synthesis Of Chiral Conducting Polymers Express Licensing Forming Adherent Coatings Using Plasma Processing Express Licensing Hydrogen Scavengers Express Licensing Laser Welding Of Fused Quartz Express Licensing Multiple Feed Powder Splitter Negotiable Licensing Boron-10 Neutron Detectors for Helium-3 Replacement Negotiable Licensing Insensitive Extrudable Explosive Negotiable Licensing Durable Fuel Cell Membrane Electrode Assembly (MEA) Express Licensing Method of Synthesis of Proton Conducting Materials

471

Advanced Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

Conducting Materials Negotiable Licensing Microseismic Tracer Particles for Hydraulic Fracturing Negotiable Licensing A Photo-Stimulated Low Electron Temperature High Current...

472

Magnetic Materials  

Science Conference Proceedings (OSTI)

Oct 27, 2009 ... Extreme magnetic fields (>2 tesla), especially when combined with temperature, are being shown to revolutionize materials processing and ...

473

materials processing  

Science Conference Proceedings (OSTI)

... of the Stainless Steel Elaborated by the Duplex Procedure (Electric Furnace- VOD Installation) [pp. ... Materials Processing on a Solar Furnace Satellite [pp.

474

Nuclear Materials  

Science Conference Proceedings (OSTI)

Materials and Fuels for the Current and Advanced Nuclear Reactors III ... response of oxide ceramics for nuclear applications through experiment, theory, and ...

475

Home Page > Business > Industrial > Global Trade Of Wood Chips Down 26% In 2009 As Pulpmills Reduce Production Worldwide, Reports Wood Resources International  

E-Print Network (OSTI)

Poster Explore Strategies in Technical Analysis from Experienced Brokers. www.Lind-Waldock.com , USA financial crises and the reduced demand for paper products worldwide. This year, only an estimated 25 worldwide, European demand for pellets and biomass chips, outlook for plantation wood chip supply, ocean

476

Quantifying And Predicting Wood Quality Of Loblolly And Slash Pine Under Intensive Forest Management Final Technical Report  

DOE Green Energy (OSTI)

The forest industry will increasingly rely on fast-growing intensively managed southern pine plantations to furnish wood and fiber. Intensive silvicultural practices, including competition control, stand density control, fertilization, and genetic improvement are yielding tremendous gains in the quantity of wood production from commercial forest land. How these technologies affect wood properties was heretofore unknown, although there is concern about the suitability of fast-grown wood for traditional forest products. A four year study was undertaken to examine the effects of these intensive practices on the properties of loblolly and slash pine wood by applying a common sampling method over 10 existing field experiments. Early weed control gets young pines off to a rapid start, often with dramatically increased growth rates. This response is all in juvenile wood however, which is low in density and strength. Similar results are found with early Nitrogen fertilization at the time of planting. These treatments increase the proportion of juvenile wood in the tree. Later, mid-rotation fertilization with Nitrogen and Phosphorus can have long term (4-8 year) growth gains. Slight reductions in wood density are short-lived (1-2 years) and occur while the tree is producing dense, stiff mature wood. Impacts of mid-rotation fertilization on wood properties for manufacturing are estimated to be minimal. Genetic differences are evident in wood density and other properties. Single family plantings showed somewhat more uniform properties than bulk improved or unimproved seedlots. Selection of genetic sources with optimal wood properties may counter some of the negative impacts of intensive weed control and fertilization. This work will allow forest managers to better predict the effects of their practices on the quality of their final product.

Richard F. Daniels; Alexander Clark III

2006-05-04T23:59:59.000Z

477

F. Composites and Hybrid Materials  

Science Conference Proceedings (OSTI)

Low-velocity Impact Response of Sandwich Composites with FRP Facesheets and Nanoclay-wood Flour Modified Polyurethane Foam · Manufacturing Process

478

Improvement of Mechanical Properties of Injection Molded Wood  

Science Conference Proceedings (OSTI)

... by one double-gate injection mould integrated an ultrasonic generator unit. ... Polymer Based Composite and Hybrid Materials for Wind Power Generation.

479

Remote Automatic Material On-Line Sensor  

DOE Green Energy (OSTI)

Low cost NMR sensor for measuring moisture content of forest products. The Department of Energy (DOE) Industries of the Future (IOF) program seeks development and implementation of technologies that make industry more efficient--in particular, more energy-efficient. Quantum Magnetics, Inc. (QM), a wholly-owned subsidiary of GE Security, received an award under the program to investigate roles for low-cost Nuclear Magnetic Resonance (NMR) technology in furtherance of these goals. Most NMR systems are designed for high-resolution spectroscopy applications. These systems use intense magnetic fields produced by superconducting magnets that drive price and operating cost to levels beyond industry tolerance. At low magnetic fields, achievable at low cost, one loses the ability to obtain spectroscopic information. However, measuring the time constants associated with the NMR signal, called NMR relaxometry, gives indications of chemical and physical states of interest to process control and optimization. It was the purpose of this effort to investigate the technical and economic feasibility of using such low-field, low-cost NMR to monitor parameters enabling greater process efficiencies. The primary target industry identified in the Cooperative Development Agreement was the wood industry, where the moisture content of wood is a key process parameter from the time the cut tree enters a mill until the time it is delivered as pieces of lumber. Extracting the moisture is energy consuming, and improvements in drying efficiency stand to reduce costs and emissions substantially. QM designed and developed a new, low-cost NMR instrument suitable for inspecting lumber up to 3 inches by 12 inches in cross section, and other materials of similar size. Low cost is achieved via an inexpensive, permanent magnet and low-cost NMR spectrometer electronics. Laboratory testing demonstrated that the NMR system is capable of accurate ({+-} 0.5%) measurements of the moisture content of wood for moisture ranging from 2% to over 140% (referenced to the wood's dry weight). Accuracy exceeded that offered by existing instrumentation when the moisture content was in excess of the fiber saturation point ({approx}20%). Accuracy was independent of the wood form: solid wood, wood chips or sawdust. The prototype NMR system was designed and built for incorporation and use in a beta test site. Beta testing is under way at the pilot plant operated by the Pulp and Paper Research Institute of Canada (PAPRICAN) in Vancouver, B.C. Other industries were also investigated. For example, laboratory testing demonstrated that low-field NMR is capable of measuring the hydrogen content of calcium oxide (quicklime). Hydrogen content measurement can be done both rapidly (on the order of 1 second) and nondestructively. Measurement of moisture in quicklime affects energy consumption in the steel industry. Further advances in system electronics, ongoing under DOD support, will enable yet more substantial system cost reductions over the prototype system, opening up a wider range of utility.

Magnuson, Erik

2005-12-20T23:59:59.000Z

480

Development and Validation of Marker-Aided Selection Methods for Wood Property Traits in Loblolly Pine and Hybrid Poplar  

SciTech Connect

Wood properties influence pulp and paper quality. Certainly, overall pulp yields are directly related to the cellulose content, changes in hemicellulose content are associated with changes in pulp cohesiveness, and pulping efficiency is related to lignin content. Despite the importance of wood properties on product quality, little progress has been made in improving such traits because current methods of assessing wood and fiber characteristics are time-consuming, expensive, and often imprecise. Genetic improvement of wood and fiber properties has been further hampered by the large size of trees, delayed reproductive maturity and long harvest cycles. Recent developments in molecular genetics will help overcome the physical, economic and biological constraints in assessing and improving wood properties. Genetic maps consisting of numerous molecular markers are now available for loblolly pine and hybrid poplar. Such markers/maps may be used as part of a marker-aided selection and breeding effort or to expedite the isolation and characterization of genes and/or promoters that directly control wood properties. The objectives of this project are: (1) to apply new and rapid analytical techniques for assessing component wood properties to segregating F2 progeny populations of loblolly pine and hybrid poplar, (2) to map quantitative trait loci and identify molecular markers associated with wood properties in each of the above species and (3) to validate marker-aided selection methods for wood properties in loblolly pine and hybrid poplar.

Tuskan, G.A.

2001-06-20T23:59:59.000Z

Note: This page contains sample records for the topic "forestry materials wood" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Development of British Columbia wood pellet life cycle inventory and its utilization in the evaluation of domestic pellet applications.  

E-Print Network (OSTI)

??An in-house life cycle inventory (LCI) database for British Columbia (BC) wood pellets is established. The LCI database is used to compare the performance of… (more)

Pa, Ann An

2010-01-01T23:59:59.000Z

482

Torrefied wood pellets as an alternative fuel to coal: Climate benefits and social desirability of production and use.  

E-Print Network (OSTI)

??The objective of this thesis is to study the climate impacts and the social returns and social desirability of torrefied wood pellet production and use… (more)

Happonen, Kiira

2012-01-01T23:59:59.000Z

483

Fuel switching from wood to LPG can benefit the environment  

SciTech Connect

The Himalaya in India is one of the world's biodiversity hotspots. Various scientific studies have reported and proven that many factors are responsible for the tremendous decline of the Himalayan forests. Extraction of wood biomass from the forests for fuel is one of the factors, as rural households rely entirely on this for their domestic energy. Efforts continue for both conservation and development of the Himalayan forests and landscape. It has been reported that people are still looking for more viable solutions that could help them to improve their lifestyle as well as facilitate ecosystem conservation and preservation of existing biodiversity. In this direction, we have documented the potential of the introduction of liquefied petroleum gas (LPG), which is one of the solutions that have been offered to the local people as a substitute for woodfuel to help meet their domestic energy demand. The results of the current study found dramatic change in per capita woodfuel consumption in the last two decades in the villages where people are using LPG. The outcome showed that woodfuel consumption had been about 475 kg per capita per year in the region, but after introduction of LPG, this was reduced to 285 kg per capita per year in 1990-1995, and was further reduced to 46 kg per capita per year in 2000-2005. Besides improving the living conditions of the local people, this transformation has had great environmental consequences. Empirical evidence shows that this new paradigm shift is having positive external effects on the surrounding forests. Consequently, we have observed a high density of tree saplings and seedlings in adjacent forests, which serves as an assessment indicator of forest health. With the help of the current study, we propose that when thinking about a top-down approach to conservation, better solutions, which are often ignored, should be offered to local people.

Nautiyal, Sunil [Leibniz-Centre for Agricultural Landscape Research (ZALF), Institute of Socioeconomics, Eberswalder Str. 84, 15374 Muencheberg (Germany)], E-mail: sunil.nautiyal@zalf.de; Kaechele, Harald [Leibniz-Centre for Agricultural Landscape Research (ZALF), Institute of Socioeconomics, Eberswalder Str. 84, 15374 Muencheberg (Germany)

2008-11-15T23:59:59.000Z

484

Materials Science Advanced Materials News  

Science Conference Proceedings (OSTI)

... Contributes to Discovery of Novel Quantum Spin-Liquid Release Date ... Novel Filter Material Could Cut Natural Gas Refining Costs Release Date: 03 ...

2010-12-16T23:59:59.000Z

485

Materials Science Advanced Materials Portal  

Science Conference Proceedings (OSTI)

... to Discovery of Novel Quantum Spin-Liquid. illustration of metal organic framework Novel Filter Material Could Cut Natural Gas Refining Costs. ...

2013-06-27T23:59:59.000Z