National Library of Energy BETA

Sample records for force base solar

  1. Nellis Air Force Base solar array provides model for renewable projects

    Broader source: Energy.gov [DOE]

    A public-private partnership has helped one Air Force base reduce its energy costs and convert to 25 percent renewable energy. Nellis Air Force Base, just north of Las Vegas, took a big step in 2007 when it installed a 14.2-megawatt, 70,000-panel photovoltaic solar array that reduced carbon dioxide emissions by 24,000 tons a year. Built partly on a landfill, the field of solar panels takes advantage of two resources plentiful in Nevada: sunshine and empty land. At its unveiling in December of 2007, the Nellis array was the largest solar panel installation in North America. The project was originally expected to produce about 30,000 megawatt-hours of electricity per year, but Steven Dumont, Air Combat Command Energy Manager, says it’s actually producing closer to 32,000 megawatt-hours, which is about 8 percent above expectations. Despite this success, Dumont said he nearly didn’t pursue the project.

  2. Hickam Air Force Base

    Broader source: Energy.gov [DOE]

    Hickam Air Force Base spans 2,850 acres in Honolulu, Hawaii. The military base is home to the 15th Airlift Wing, the Hawaii Air National Guard, and the Pacific Air Forces headquarters.

  3. American Recovery and Reinvestment Act (ARRA) Federal Energy Management Program Technical Assistance Project 224 Altus Air Force Base Solar Technologies

    SciTech Connect (OSTI)

    Russo, Bryan J.

    2010-09-30

    The principal goal of this project was to evaluate altus Air Force Base for building integrated silicon or thin film module photovoltaic opportunities. This report documents PNNL's efforts and documents study conclusions.

  4. Hill Air Force Base | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hill Air Force Base Hill Air Force Base Hill Air Force Base Overview Energy savings performance contracting at Hill Air Force Base generated much interest during a recent training session on energy management that downlinked 12 Department of Defense sites. Energy systems in 940 buildings on the Base will be upgraded under an 18-year ESPC between the Government and the energy service company, CES/Way. Improvements are distributed over five task orders that will be completed in five years, with

  5. ESPC Success Story - Dyess Air Force Base

    Energy Savers [EERE]

    DYESS AIR FORCE BASE DYESS, TEXAS Water Conservation and Green Energy ESPC SUCCESS STORY Dyess Air Force Base and surrounding west Texas has been under extreme-drought water ...

  6. Hill Air Force Base | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Energy savings performance contracting at Hill Air Force Base generated much interest ... There was a need to reduce energy and water use at Hill Air Force Base, which is subjected ...

  7. Renewable Hydrogen Production at Hickam Air Force Base | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    at Hickam Air Force Base Renewable Hydrogen Production at Hickam Air Force Base Presented at the Renewable Hydrogen Workshop, Nov. 16, 2009, in Palm Springs, CA PDF icon ...

  8. Hickam Air Force Base Fuel Cell Vehicles: Early Implementation...

    Broader source: Energy.gov (indexed) [DOE]

    operating at Hickam Air Force Base in Honolulu, Hawaii. PDF icon 42233.pdf More Documents & Publications Renewable Hydrogen Production at Hickam Air Force Base Hydrogen and ...

  9. Comprehensive Energy Program at Patrick Air Force Base Set to...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Comprehensive Energy Program at Patrick Air Force Base Set to Exceed Energy Goals Comprehensive Energy Program at Patrick Air Force Base Set to Exceed Energy Goals Federal Energy ...

  10. DOE - Office of Legacy Management -- Nellis Air Force Base -...

    Office of Legacy Management (LM)

    Nellis Air Force Base - NV 04 FUSRAP Considered Sites Site: NELLIS AIR FORCE BASE (NV.04) Eliminated from consideration under FUSRAP - Referred to DOD Designated Name: Not ...

  11. Solar Community Comes Out in Full Force for SunShot Grand Challenge...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Packed House Solar Community Comes Out in Full Force for SunShot Grand Challenge Summit Ali Zaidi, Deputy Director for Energy Policy, The White House Domestic Policy Council ...

  12. Comprehensive Energy Program at Patrick Air Force Base Set to...

    Energy Savers [EERE]

    The 45 th Space Wing at Patrick Air Force Base (PAFB) is pursuing its energy goals through ... Comprehensive Energy Program at Patrick Air Force Base Set to Exceed Energy Goals ...

  13. Hickam Air Force Base Fuel Cell Vehicles: Early Implementation Experience |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Hickam Air Force Base Fuel Cell Vehicles: Early Implementation Experience Hickam Air Force Base Fuel Cell Vehicles: Early Implementation Experience This report sumarizes early implementation experience from an evaluation of two prototype fuel cell vehicles operating at Hickam Air Force Base in Honolulu, Hawaii. PDF icon 42233.pdf More Documents & Publications Renewable Hydrogen Production at Hickam Air Force Base Hydrogen and Fuel Cell Transit Bus Evaluations: Joint

  14. Hickam Air Force Base Fuel Cell Vehicles: Early Implementation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technical Report NRELTP-560-42233 October 2007 Hickam Air Force Base Fuel Cell Vehicles: Early Implementation Experience Leslie Eudy, National Renewable Energy Laboratory Kevin ...

  15. Information-based physics, influence, and forces

    SciTech Connect (OSTI)

    Walsh, James Lyons; Knuth, Kevin H.

    2015-01-13

    In recent works, Knuth and Bahreyni have demonstrated that the concepts of space and time are emergent in a coarse-grained model of direct particle-particle influence. In addition, Knuth demonstrated that observer-made inferences regarding the free particle, which is defined as a particle that influences others, but is not itself influenced, result in a situation identical to the Feynman checkerboard model of the Dirac equation. This suggests that the same theoretical framework that gives rise to an emergent spacetime is consistent with quantum mechanics. In this paper, we begin to explore the effect of influence on the emergent properties of a particle. This initial study suggests that when a particle is influenced, it is interpreted as accelerating in a manner consistent with special relativity implying that, at least in this situation, influence can be conceived of as a force.

  16. A Supramolecular Complex in Small-Molecule Solar Cells based...

    Office of Scientific and Technical Information (OSTI)

    in Small-Molecule Solar Cells based on Contorted Aromatic Molecules Citation Details In-Document Search Title: A Supramolecular Complex in Small-Molecule Solar Cells based on ...

  17. Optimal Driving Force for Converting Excitons into Free Carriers in Excitonic Solar Cells

    SciTech Connect (OSTI)

    Coffey, D. C.; Larson, B. W.; Hains, A. W.; Whitaker, J. B.; Kopidakis, N.; Boltalina, O. V.; Strauss, S. H.; Rumbles, G.

    2012-04-26

    A general but limiting characteristic in excitonic photovoltaics is that a portion of the incident photon energy appears necessary for converting excitons into electrical charges, resulting in a loss of efficiency. Currently, the mechanism underlying this process is unclear. Here, we describe the development of an experimental method for measuring charge creation yields in organic solar cell materials. We use this method to examine a series of conjugated polymer:fullerene blend films and observe two unexpected features: the existence of an optimal driving force and a loss in conversion efficiency if this force is exceeded. These observations have implications for the design of excitonic photovoltaic devices and can be explained by a simple Marcus formulation that introduces the importance of reorganization energy.

  18. Economical Pyrite-Based Solar Cells - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solar Photovoltaic Solar Photovoltaic Advanced Materials Advanced Materials Find More Like This Return to Search Economical Pyrite-Based Solar Cells University of Colorado Contact CU About This Technology Publications: PDF Document Publication CU3131B (Pyrite Solar Cells) Marketing Summary_1.pdf (170 KB) Technology Marketing Summary The first generation of solar cells, used in 90% of today's cells, have a focus of high efficiency. These cells use a single p-n junction to extract energy from

  19. Spectral Solar Radiation Data Base at NREL

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    *In September 1991 the Solar Energy Research Institute became the National Renewable Energy Laboratory. [Description taken from http://rredc.nrel.gov/solar/old_data/spectral/

  20. Cross-sectional electrostatic force microscopy of thin-film solar cells

    SciTech Connect (OSTI)

    Ballif, C.; Moutinho, H. R.; Al-Jassim, M. M.

    2001-01-15

    In a recent work, we showed that atomic force microscopy (AFM) is a powerful technique to image cross sections of polycrystalline thin films. In this work, we apply a modification of AFM, namely, electrostatic force microscopy (EFM), to investigate the electronic properties of cleaved II--VI and multijunction thin-film solar cells. We cleave the devices in such a way that they are still working with their nominal photovoltaic efficiencies and can be polarized for the measurements. This allows us to differentiate between surface effects (work function and surface band bending) and bulk device properties. In the case of polycrystalline CdTe/CdS/SnO{sub 2}/glass solar cells, we find a drop of the EFM signal in the area of the CdTe/CdS interface ({+-}50 nm). This drop varies in amplitude and sign according to the applied external bias and is compatible with an n-CdS/p-CdTe heterojunction model, thereby invalidating the possibility of a deeply buried n-p CdTe homojunction. In the case of a triple-junction GaInP/GaAs/Ge device, we observe a variation of the EFM signal linked to both the material work-function differences and to the voltage bias applied to the cell. We attempt a qualitative explanation of the results and discuss the implications and difficulties of the EFM technique for the study of such thin-film devices.

  1. Modeling tropical Pacific sea surface temperature with satellite-derived solar radiative forcing

    SciTech Connect (OSTI)

    Seager, R.; Blumenthal, M.B.

    1994-12-01

    Two independent datasets for the solar radiation at the surface derived from satellites are compared. The data derived from the Earth Radiation Budget Experiment (ERBE) is for the net solar radiation at the surface whereas the International Satellite Cloud Climatology Project (ISCCP) data is for the downward flux only and was corrected with a space- and time-varying albedo. The ISCCP net flux is at all times higher than the ERBE flux. The difference can be divided into an offset that decreases with latitude and another component that correlates with high tropical cloud cover. With this latter exception the two datasets provide spatial patterns of solar flux that are very similar. A tropical Pacific Ocean model is forced with these two datasets and observed climatological winds. The upward heat flux is parameterized taking into account separately the longwave radiative, latent, and sensible heat fluxes. Best fit values for the uncertain parameters are found using an optimization procedure that seeks to minimize the difference between model and observed SST by varying the parameters within a reasonable range of uncertainty. The SST field the model produces with the best fit parameters is the best the model can do. If the differences between the model and data are larger than can be accounted for by remaining uncertainties in the heat flux parameterization and forcing data then the ocean model must be held to be at fault. Using this method of analysis, a fundamental model fault is identified. Inadequate treatment of mixed layer/entrainment processes in upwelling regions of the eastern tropical Pacific leads to a large and seasonally varying error in the model SST. Elsewhere the model SST is insufficiently different from observed to be able to identify model errors.

  2. Force-Based Needle Insertion for Medical Applications (Conference) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect Conference: Force-Based Needle Insertion for Medical Applications Citation Details In-Document Search Title: Force-Based Needle Insertion for Medical Applications No abstract prepared. Authors: Love, Lonnie J [1] ; Jansen, John F [1] ; Lloyd, Peter D [1] + Show Author Affiliations ORNL Publication Date: 2009-01-01 OSTI Identifier: 966427 DOE Contract Number: DE-AC05-00OR22725 Resource Type: Conference Resource Relation: Conference: IROS 2009: The 2009 IEEE/RSJ International

  3. F.E. Warren Air Force Base Wind Farm | Open Energy Information

    Open Energy Info (EERE)

    F.E. Warren Air Force Base Wind Farm Jump to: navigation, search Name F.E. Warren Air Force Base Wind Farm Facility F.E. Warren Air Force Base Sector Wind energy Facility Type...

  4. Hawaii Marine Base Installs Solar Roofs | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Lorelei Laird Writer, Energy Empowers What does this project do? Marine Corps Base Hawaii replaced roofs on two buildings with polyvinyl chloride membrane 'cool' roofs and solar...

  5. Separable solutions of force-free spheres and applications to solar active regions

    SciTech Connect (OSTI)

    Prasad, A.; Mangalam, A.; Ravindra, B. E-mail: mangalam@iiap.res.in

    2014-05-10

    We present a systematic study of the force-free field equation for simple axisymmetric configurations in spherical geometry and apply it to the solar active regions. The condition of separability of solutions in the radial and angular variables leads to two classes of solutions: linear and nonlinear force-free fields (NLFF). We have studied these linear solutions and extended the nonlinear solutions for the radial power law index to the irreducible rational form n = p/q, which is allowed for all cases of odd p and cases of q > p for even p, where the poloidal flux ??1/r{sup n} and the field B?1/r {sup n+2}. We apply these solutions to simulate photospheric vector magnetograms obtained using the spectropolarimeter on board Hinode. The effectiveness of our search strategy is first demonstrated on test inputs of dipolar, axisymmetric, and nonaxisymmetric linear force-free fields. Using the best fit, we build three-dimensional axisymmetric field configurations and calculate the energy and relative helicity with two independent methods, which are in agreement. We have analyzed five magnetograms for AR 10930 spanning a period of three days during which two X-class flares occurred and found the free energy and relative helicity of the active region before and after the flare; our analysis indicates a peak in these quantities before the flare events, which is consistent with the other results. We also analyzed single-polarity regions AR 10923 and 10933, which showed very good fits to potential fields. This method provides useful reconstruction of NLFF and input fields for other numerical techniques.

  6. Sandia Energy - Areva Solar and Sandia Labs Join Forces for CLFR...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Areva Solar is collaborating with Sandia National Laboratories on a new concentrated solar power (CSP) installation with thermal energy storage. The CSP storage project combines...

  7. Nonlinear force-free field modeling of the solar magnetic carpet and comparison with SDO/HMI and Sunrise/IMAX observations

    SciTech Connect (OSTI)

    Chitta, L. P.; Kariyappa, R.; Van Ballegooijen, A. A.; DeLuca, E. E.; Solanki, S. K.

    2014-10-01

    In the quiet solar photosphere, the mixed polarity fields form a magnetic carpet that continuously evolves due to dynamical interaction between the convective motions and magnetic field. This interplay is a viable source to heat the solar atmosphere. In this work, we used the line-of-sight (LOS) magnetograms obtained from the Helioseismic and Magnetic Imager on the Solar Dynamics Observatory, and the Imaging Magnetograph eXperiment instrument on the Sunrise balloon-borne observatory, as time-dependent lower boundary conditions, to study the evolution of the coronal magnetic field. We use a magneto-frictional relaxation method, including hyperdiffusion, to produce a time series of three-dimensional nonlinear force-free fields from a sequence of photospheric LOS magnetograms. Vertical flows are added up to a height of 0.7 Mm in the modeling to simulate the non-force-freeness at the photosphere-chromosphere layers. Among the derived quantities, we study the spatial and temporal variations of the energy dissipation rate and energy flux. Our results show that the energy deposited in the solar atmosphere is concentrated within 2 Mm of the photosphere and there is not sufficient energy flux at the base of the corona to cover radiative and conductive losses. Possible reasons and implications are discussed. Better observational constraints of the magnetic field in the chromosphere are crucial to understand the role of the magnetic carpet in coronal heating.

  8. Demonstration of Security Benefits of Renewable Generation at FE Warren Air Force Base

    SciTech Connect (OSTI)

    Warwick, William M.; Myers, Kurt; Seifert, Gary

    2010-12-31

    Report detailing field demonstration of security benefits of renewable generation at FE Warren Air Force Base.

  9. Eielson Air Force Base Operable Unit 2 baseline risk assessment

    SciTech Connect (OSTI)

    Lewis, R.E.; Jarvis, T.T.; Jarvis, M.R.; Whelan, G.

    1994-10-01

    Operable Unit 2 at Eielson Air Force Base (AFB) near Fairbanks, is one of several operable units characterized by petroleum, oil, and lubricant contamination, and by the presence of organic products floating at the water table, as a result of Air Force operations since the 1940s. The base is approximately 19,270 acres in size, and comprises the areas for military operations and a residential neighborhood for military dependents. Within Operable Unit 2, there are seven source areas. These source areas were grouped together primarily because of the contaminants released and hence are not necessarily in geographical proximity. Source area ST10 includes a surface water body (Hardfill Lake) next to a fuel spill area. The primary constituents of concern for human health include benzene, toluene, ethylbenzene, and xylenes (BTEX). Monitored data showed these volatile constituents to be present in groundwater wells. The data also showed an elevated level of trace metals in groundwater.

  10. Born on an Air Force base in Mississippi, Jan never

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Born on an Air Force base in Mississippi, Jan never lived any place for more than three years as a child. Her family moved to Germany when she was seven, and she recalls trips all over Europe. "We visited Holland, camped in Italy for a summer, and toured numerous museums and castles. My dad had been a pilot in World War II and Korea, and he took us to Hitler's Eagle's Nest retreat, and even to the Dachau concentration camp. These made extremely strong impressions of the influences of

  11. Solar Community Comes Out in Full Force for SunShot Grand Challenge Summit

    Broader source: Energy.gov [DOE]

    A packed crowd of leaders across the solar community gathered in Anaheim, California, for the 2014 SunShot Grand Challenge Summit.

  12. Comprehensive Energy Program at Patrick Air Force Base Set to Exceed Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Goals | Department of Energy Comprehensive Energy Program at Patrick Air Force Base Set to Exceed Energy Goals Comprehensive Energy Program at Patrick Air Force Base Set to Exceed Energy Goals Federal Energy Management Program case study focuses on Patrick Air Force Base's use of a utility energy services contract to achieve its energy goals. PDF icon Download the Patrick Air Force Base case study. More Documents & Publications FPL Energy Services ESCO Qualification Sheet UESC Project

  13. A Physically-Based Estimate of Radiative Forcing by Anthropogenic...

    Office of Scientific and Technical Information (OSTI)

    The radiative forcing is sensitive to the model's horizontal resolution, the use of predicted vs. analyzed relative humidity, the prediction vs. diagnosis of aerosol number and ...

  14. Solar Community Comes Out in Full Force for SunShot Grand Challenge Summit

    Broader source: Energy.gov [DOE]

    This week in sunny Anaheim, California, more than 800 solar industry leaders gathered for the 2014 SunShot Grand Challenge Summit. The Summit, launched by the Energy Department’s SunShot Initiative...

  15. Hawaii Marine Base Installs Solar Roofs

    Broader source: Energy.gov [DOE]

    Harnessing sunlight to create renewable electricity at Hawaii's Marine Corps Base was considered too expensive to be practical -- until 2008.

  16. Progress on an Updated National Solar Radiation Data Base: Preprint

    SciTech Connect (OSTI)

    Wilcox, S.; Anderberg, M.; George, R.; Marion, W.; Myers, D.; Renne, D.; Beckman, W.; DeGaetano, A.; Gueymard, C.; Perez, R.; Plantico, M.; Stackhouse, P.; Vignola, F.

    2004-03-01

    In 1992, The National Renewable Energy Laboratory (NREL) released the 1961-1990 National Solar Radiation Data Base (NSRDB), a 30-year set of hourly solar radiation data. In April 2003, NREL convened a meeting of experts to investigate issues concerning a proposed update of the NSRDB. The panel determined that an important difficulty posed by the update was the shift from manual to automated cloud observations at National Weather Service stations in the United States. The solar model used in the original NSRDB relied heavily on the methodology and resolution of the manual cloud observations. The meeting participants recommended that NREL produce a plan for creating an update using currently available meteorological observations and satellite imagery. This paper describes current progress toward a plan for an updated NSRDB.

  17. A Physically-Based Estimate of Radiative Forcing by Anthropogenic Sulfate

    Office of Scientific and Technical Information (OSTI)

    Aerosol (Journal Article) | SciTech Connect Journal Article: A Physically-Based Estimate of Radiative Forcing by Anthropogenic Sulfate Aerosol Citation Details In-Document Search Title: A Physically-Based Estimate of Radiative Forcing by Anthropogenic Sulfate Aerosol Estimates of direct and indirect radiative forcing by anthropogenic sulfate aerosols from an integrated global aerosol and climate modeling system are presented. A detailed global tropospheric chemistry and aerosol model that

  18. Solar

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power ... comprehensively recording solar irradiance data to accompany its outdoor PV testing. ...

  19. Prediction of global solar irradiance based on time series analysis: Application to solar thermal power plants energy production planning

    SciTech Connect (OSTI)

    Martin, Luis; Marchante, Ruth; Cony, Marco; Zarzalejo, Luis F.; Polo, Jesus; Navarro, Ana

    2010-10-15

    Due to strong increase of solar power generation, the predictions of incoming solar energy are acquiring more importance. Photovoltaic and solar thermal are the main sources of electricity generation from solar energy. In the case of solar thermal energy plants with storage energy system, its management and operation need reliable predictions of solar irradiance with the same temporal resolution as the temporal capacity of the back-up system. These plants can work like a conventional power plant and compete in the energy stock market avoiding intermittence in electricity production. This work presents a comparisons of statistical models based on time series applied to predict half daily values of global solar irradiance with a temporal horizon of 3 days. Half daily values consist of accumulated hourly global solar irradiance from solar raise to solar noon and from noon until dawn for each day. The dataset of ground solar radiation used belongs to stations of Spanish National Weather Service (AEMet). The models tested are autoregressive, neural networks and fuzzy logic models. Due to the fact that half daily solar irradiance time series is non-stationary, it has been necessary to transform it to two new stationary variables (clearness index and lost component) which are used as input of the predictive models. Improvement in terms of RMSD of the models essayed is compared against the model based on persistence. The validation process shows that all models essayed improve persistence. The best approach to forecast half daily values of solar irradiance is neural network models with lost component as input, except Lerida station where models based on clearness index have less uncertainty because this magnitude has a linear behaviour and it is easier to simulate by models. (author)

  20. Dyess Air Force Base Water Conservation and Green Energy | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Dyess Air Force Base Water Conservation and Green Energy Dyess Air Force Base Water Conservation and Green Energy Fact sheet describes the Federal Energy Management Program (FEMP) Energy Savings Performance Contract (ESPC) Success Story on water conservation and green energy at Dyess Air Foce Base at Dyess, Texas. PDF icon espc_ss_dyess.pdf More Documents & Publications Energy Savings Performance Contract Success Stories Energy Savings Performance Contract ENABLE Briefing Harold

  1. Improved Electrodes and Electrolytes for Dye-Based Solar Cells

    SciTech Connect (OSTI)

    Harry R. Allcock; Thomas E. Mallouk; Mark W. Horn

    2011-10-26

    The most important factor in limiting the stability of dye-sensitized solar cells is the use of volatile liquid solvents in the electrolytes, which causes leakage during extended operation especially at elevated temperatures. This, together with the necessary complex sealing of the cells, seriously hampers the industrial-scale manufacturing and commercialization feasibilities of DSSCs. The objective of this program was to bring about a significant improvement in the performance and longevity of dye-based solar cells leading to commercialization. This had been studied in two ways first through development of low volatility solid, gel or liquid electrolytes, second through design and fabrication of TiO2 sculptured thin film electrodes.

  2. Distribution System Audits, Leak Detection, and Repair: Kirtland Air Force Base Leak Detection and Repair Program

    SciTech Connect (OSTI)

    2009-01-14

    Water Best Management Practice #3 Fact Seet: Outlines how a leak detection and repair program helped Kirtland Air Force Base perform distribution system audits, leak detection, and repair to conserve water site-wide.

  3. NONLINEAR FORCE-FREE FIELD EXTRAPOLATION OF A CORONAL MAGNETIC FLUX ROPE SUPPORTING A LARGE-SCALE SOLAR FILAMENT FROM A PHOTOSPHERIC VECTOR MAGNETOGRAM

    SciTech Connect (OSTI)

    Jiang, Chaowei; Wu, S. T.; Hu, Qiang; Feng, Xueshang E-mail: wus@uah.edu E-mail: fengx@spaceweather.ac.cn

    2014-05-10

    Solar filaments are commonly thought to be supported in magnetic dips, in particular, in those of magnetic flux ropes (FRs). In this Letter, based on the observed photospheric vector magnetogram, we implement a nonlinear force-free field (NLFFF) extrapolation of a coronal magnetic FR that supports a large-scale intermediate filament between an active region and a weak polarity region. This result is a first, in the sense that current NLFFF extrapolations including the presence of FRs are limited to relatively small-scale filaments that are close to sunspots and along main polarity inversion lines (PILs) with strong transverse field and magnetic shear, and the existence of an FR is usually predictable. In contrast, the present filament lies along the weak-field region (photospheric field strength ? 100G), where the PIL is very fragmented due to small parasitic polarities on both sides of the PIL and the transverse field has a low signal-to-noise ratio. Thus, extrapolating a large-scale FR in such a case represents a far more difficult challenge. We demonstrate that our CESE-MHD-NLFFF code is sufficient for the challenge. The numerically reproduced magnetic dips of the extrapolated FR match observations of the filament and its barbs very well, which strongly supports the FR-dip model for filaments. The filament is stably sustained because the FR is weakly twisted and strongly confined by the overlying closed arcades.

  4. Development of a quartz tuning-fork-based force sensor for measurements in the tens of nanoNewton force range during nanomanipulation experiments

    SciTech Connect (OSTI)

    Oiko, V. T. A. Rodrigues, V.; Ugarte, D.; Martins, B. V. C.; Silva, P. C.

    2014-03-15

    Understanding the mechanical properties of nanoscale systems requires new experimental and theoretical tools. In particular, force sensors compatible with nanomechanical testing experiments and with sensitivity in the nN range are required. Here, we report the development and testing of a tuning-fork-based force sensor for in situ nanomanipulation experiments inside a scanning electron microscope. The sensor uses a very simple design for the electronics and it allows the direct and quantitative force measurement in the 1100 nN force range. The sensor response is initially calibrated against a nN range force standard, as, for example, a calibrated Atomic Force Microscopy cantilever; subsequently, applied force values can be directly derived using only the electric signals generated by the tuning fork. Using a homemade nanomanipulator, the quantitative force sensor has been used to analyze the mechanical deformation of multi-walled carbon nanotube bundles, where we analyzed forces in the 540 nN range, measured with an error bar of a few nN.

  5. Amorphous silicon carbide passivating layers for crystalline-silicon-based heterojunction solar cells

    SciTech Connect (OSTI)

    Boccard, Mathieu; Holman, Zachary C.

    2015-08-14

    With this study, amorphous silicon enables the fabrication of very high-efficiency crystalline-silicon-based solar cells due to its combination of excellent passivation of the crystalline silicon surface and permeability to electrical charges. Yet, amongst other limitations, the passivation it provides degrades upon high-temperature processes, limiting possible post-deposition fabrication possibilities (e.g., forcing the use of low-temperature silver pastes). We investigate the potential use of intrinsic amorphous silicon carbide passivating layers to sidestep this issue. The passivation obtained using device-relevant stacks of intrinsic amorphous silicon carbide with various carbon contents and doped amorphous silicon are evaluated, and their stability upon annealing assessed, amorphous silicon carbide being shown to surpass amorphous silicon for temperatures above 300°C. We demonstrate open-circuit voltage values over 700 mV for complete cells, and an improved temperature stability for the open-circuit voltage. Transport of electrons and holes across the hetero-interface is studied with complete cells having amorphous silicon carbide either on the hole-extracting side or on the electron-extracting side, and a better transport of holes than of electrons is shown. Also, due to slightly improved transparency, complete solar cells using an amorphous silicon carbide passivation layer on the hole-collecting side are demonstrated to show slightly better performances even prior to annealing than obtained with a standard amorphous silicon layer.

  6. Amorphous silicon carbide passivating layers for crystalline-silicon-based heterojunction solar cells

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Boccard, Mathieu; Holman, Zachary C.

    2015-08-14

    With this study, amorphous silicon enables the fabrication of very high-efficiency crystalline-silicon-based solar cells due to its combination of excellent passivation of the crystalline silicon surface and permeability to electrical charges. Yet, amongst other limitations, the passivation it provides degrades upon high-temperature processes, limiting possible post-deposition fabrication possibilities (e.g., forcing the use of low-temperature silver pastes). We investigate the potential use of intrinsic amorphous silicon carbide passivating layers to sidestep this issue. The passivation obtained using device-relevant stacks of intrinsic amorphous silicon carbide with various carbon contents and doped amorphous silicon are evaluated, and their stability upon annealing assessed, amorphousmore » silicon carbide being shown to surpass amorphous silicon for temperatures above 300°C. We demonstrate open-circuit voltage values over 700 mV for complete cells, and an improved temperature stability for the open-circuit voltage. Transport of electrons and holes across the hetero-interface is studied with complete cells having amorphous silicon carbide either on the hole-extracting side or on the electron-extracting side, and a better transport of holes than of electrons is shown. Also, due to slightly improved transparency, complete solar cells using an amorphous silicon carbide passivation layer on the hole-collecting side are demonstrated to show slightly better performances even prior to annealing than obtained with a standard amorphous silicon layer.« less

  7. National Solar Radiation Data Bases (NSRDB): 1961 to 1990 and 1991 to 2005

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The National Solar Radiation Data Base 1961-1990 (NSRDB) contains 30 years of solar radiation and supplementary meteorological data from 237 NWS sites in the U.S., plus sites in Guam and Puerto Rico. The updated 1991-2005 National Solar Radiation Database holds solar and meteorological data for 1,454 locations in the United States and its territories. See also the interactive data maps for the 1961 to 1990 data at http://rredc.nrel.gov/solar/old_data/nsrdb/1961-1990/redbook/atlas/.

  8. Three Military Bases Partner with Energy Department to Train Veterans for Solar Jobs

    Broader source: Energy.gov [DOE]

    Today, the first class of Marine trainees at Camp Pendleton will graduate from the Energy Departments solar job training pilot program, which is aimed at preparing service members for careers in the solar industry as solar photovoltaic system installers, sales representatives, system inspectors, and other solar-related opportunities. Camp Pendleton is one of three military bases partnering with the Departments SunShot Initiative to train 200 transitioning military service members during the pilot period for employment opportunities in the rapidly growing U.S. solar energy industry. Training courses will also begin at Fort Carson and Naval Station Norfolk this spring.

  9. solar

    National Nuclear Security Administration (NNSA)

    2%2A en Solar power purchase for DOE laboratories http:nnsa.energy.govmediaroompressreleasessolarpower

  10. Tejas Solares | Open Energy Information

    Open Energy Info (EERE)

    Tejas Solares Jump to: navigation, search Name: Tejas Solares Place: Spain Sector: Solar Product: Tejas Solares is a Spain-based company focused on providing solar solutions for...

  11. SBM Solar | Open Energy Information

    Open Energy Info (EERE)

    search Name: SBM Solar Place: North Carolina Sector: Solar Product: SBM Solar is a solar panel manufacturer based in North Carolina. References: SBM Solar1 This article is...

  12. Current enhancement of CdTe-based solar cells

    SciTech Connect (OSTI)

    Paudel, Naba R.; Poplawsky, Jonathan D.; More, Karren Leslie; Yan, Yanfa

    2015-07-30

    We report on the realization of CdTe solar cell photocurrent enhancement using an n-type CdSe heterojunction partner sputtered on commercial SnO2/SnO2:F coated soda-lime glass substrates. With high-temperature close-space sublimation CdTe deposition followed by CdCl2 activation, this thin-film stack allows for substantial interdiffusion at the CdSe/CdTe interface facilitating a CdSexTe1-x alloy formation. The bowing effect causes a reduced optical bandgap of the alloyed absorber layer and, therefore, leads to current enhancement in the long-wavelength region and a decrease in open-circuit voltage (VOC). To overcome the VOC loss and maintain a high short-circuit current (JSC), the CdTe cell configuration has been modified using combined CdS:O/CdSe window layers. The new device structure has demonstrated enhanced collection from both short-and long-wavelength regions as well as a VOC improvement. With an optimized synthesis process, a small-area cell using CdS:O/CdSe window layer showed an efficiency of 15.2% with a VOC of 831 mV, a JSC of 26.3 mA/cm2, and a fill factor of 69.5%, measured under an AM1.5 illumination without antireflection coating. Furthermore, the results provide new directions for further improvement of CdTe-based solar cells.

  13. Current enhancement of CdTe-based solar cells

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Paudel, Naba R.; Poplawsky, Jonathan D.; More, Karren Leslie; Yan, Yanfa

    2015-07-30

    We report on the realization of CdTe solar cell photocurrent enhancement using an n-type CdSe heterojunction partner sputtered on commercial SnO2/SnO2:F coated soda-lime glass substrates. With high-temperature close-space sublimation CdTe deposition followed by CdCl2 activation, this thin-film stack allows for substantial interdiffusion at the CdSe/CdTe interface facilitating a CdSexTe1-x alloy formation. The bowing effect causes a reduced optical bandgap of the alloyed absorber layer and, therefore, leads to current enhancement in the long-wavelength region and a decrease in open-circuit voltage (VOC). To overcome the VOC loss and maintain a high short-circuit current (JSC), the CdTe cell configuration has been modifiedmore » using combined CdS:O/CdSe window layers. The new device structure has demonstrated enhanced collection from both short-and long-wavelength regions as well as a VOC improvement. With an optimized synthesis process, a small-area cell using CdS:O/CdSe window layer showed an efficiency of 15.2% with a VOC of 831 mV, a JSC of 26.3 mA/cm2, and a fill factor of 69.5%, measured under an AM1.5 illumination without antireflection coating. Furthermore, the results provide new directions for further improvement of CdTe-based solar cells.« less

  14. New GE Plant to Produce Thin Film PV Solar Panels Based on NREL Technology

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy GE Plant to Produce Thin Film PV Solar Panels Based on NREL Technology New GE Plant to Produce Thin Film PV Solar Panels Based on NREL Technology April 22, 2011 - 10:17am Addthis Photo courtesy of General Electric Photo courtesy of General Electric Minh Le Minh Le Deputy Director, Solar Energy Technologies Office Earlier this month, General Electric announced plans to enter the global marketplace for solar photovoltaic (PV) panels in a big way - and to do it, they will

  15. Mountain Home Air Force Base, Idaho Geothermal Resource Assessment and Future Recommendations

    SciTech Connect (OSTI)

    Joseph C. Armstrong; Robert P. Breckenridge; Dennis L. Nielson; John W. Shervais; Thomas R. Wood

    2013-03-01

    The U.S. Air Force is facing a number of challenges as it moves into the future, one of the biggest being how to provide safe and secure energy to support base operations. A team of scientists and engineers met at Mountain Home Air Force Base in early 2011 near Boise, Idaho, to discuss the possibility of exploring for geothermal resources under the base. The team identified that there was a reasonable potential for geothermal resources based on data from an existing well. In addition, a regional gravity map helped identify several possible locations for drilling a new well. The team identified several possible sources of funding for this well—the most logical being to use U.S. Department of Energy funds to drill the upper half of the well and U.S. Air Force funds to drill the bottom half of the well. The well was designed as a slimhole well in accordance with State of Idaho Department of Water Resources rules and regulations. Drilling operations commenced at the Mountain Home site in July of 2011 and were completed in January of 2012. Temperatures increased gradually, especially below a depth of 2000 ft. Temperatures increased more rapidly below a depth of 5500 ft. The bottom of the well is at 5976 ft, where a temperature of about 140°C was recorded. The well flowed artesian from a depth below 5600 ft, until it was plugged off with drilling mud. Core samples were collected from the well and are being analyzed to help understand permeability at depth. Additional tests using a televiewer system will be run to evaluate orientation and directions at fractures, especially in the production zone. A final report on the well exploitation will be forthcoming later this year. The Air Force will use it to evaluate the geothermal resource potential for future private development options at Mountain Home Air Force Base. In conclusion, Recommendation for follow-up efforts include the following:

  16. Performance enhancement of thin film silicon solar cells based on distributed Bragg reflector and diffraction grating

    SciTech Connect (OSTI)

    Dubey, R. S.; Saravanan, S.; Kalainathan, S.

    2014-12-15

    The influence of various designing parameters were investigated and explored for high performance solar cells. Single layer grating based solar cell of 50 μm thickness gives maximum efficiency up to 24 % whereas same efficiency is achieved with the use of three bilayers grating based solar cell of 30 μm thickness. Remarkably, bilayer grating based solar cell design not only gives broadband absorption but also enhancement in efficiency with reduced cell thickness requirement. This absorption enhancement is attributed to the high reflection and diffraction from DBR and grating respectively. The obtained short-circuit current were 29.6, 32.9, 34.6 and 36.05 mA/cm{sup 2} of 5, 10, 20 and 30 μm cell thicknesses respectively. These presented designing efforts would be helpful to design and realize new generation of solar cells.

  17. Solar

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear Energy Nuclear

  18. Solar

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear Energy Nuclear

  19. Geothermal exploration program, Hill Air Force Base, Davis and Weber Counties, Utah

    SciTech Connect (OSTI)

    Glenn, W.E.; Chapman, D.S.; Foley, D.; Capuano, R.M.; Cole, D.; Sibbett, B.; Ward, S.H.

    1980-03-01

    Results obtained from a program designed to locate a low- or moderate-temperature geothermal resource that might exist beneath Hill Air Force Base (AFB), Ogden, Utah are discussed. A phased exploration program was conducted at Hill AFB. Published geological, geochemical, and geophysical reports on the area were examined, regional exploration was conducted, and two thermal gradient holes were drilled. This program demonstrated that thermal waters are not present in the shallow subsurface at this site. (MHR)

  20. Exploration and Resource Assessment at Mountain Home Air Force Base, Idaho Using an Integrated Team Approach

    SciTech Connect (OSTI)

    Joseph C. Armstrong; Robert P. Breckenridge; Dennis L. Nielson; John W. Shervais; Thomas R. Wood

    2012-10-01

    The U.S. Air Force is facing a number of challenges as it moves into the future, one of the biggest being how to provide safe and secure energy to support base operations. A team of scientists and engineers met at Mountain Home Air Force Base near Boise, Idaho, to discuss the possibility of exploring for geothermal resources under the base. The team identified that there was a reasonable potential for geothermal resources based on data from an existing well. In addition, a regional gravity map helped identify several possible locations for drilling a new well. The team identified several possible sources of funding for this well—the most logical being to use U.S. Department of Energy funds to drill the upper half of the well and U.S. Air Force funds to drill the bottom half of the well. The well was designed as a slimhole well in accordance with State of Idaho Department of Water Resources rules and regulations. Drilling operations commenced at the Mountain Home site in July of 2011 and were completed in January of 2012. Temperatures increased gradually, especially below a depth of 2000 ft. Temperatures increased more rapidly below a depth of 5500 ft. The bottom of the well is at 5976 ft, where a temperature of about 140°C was recorded. The well flowed artesian from a depth below 5600 ft, until it was plugged off with drilling mud. Core samples were collected from the well and are being analyzed to help understand permeability at depth. Additional tests using a televiewer system will be run to evaluate orientation and directions at fractures, especially in the production zone. A final report on the well exploitation will be forthcoming later this year. The Air Force will use it to evaluate the geothermal resource potential for future private development options at Mountain Home AFB.

  1. PROJECT PROFILE: Silicon-Based Tandem Solar Cells | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Silicon-Based Tandem Solar Cells PROJECT PROFILE: Silicon-Based Tandem Solar Cells Funding Opportunity: SuNLaMP SunShot Subprogram: Photovoltaics Location: National Renewable Energy Laboratory, Golden, CO Amount Awarded: $1,500,000 The project will demonstrate bonded gallium indium phosphide (GaInP) on silicon tandem cells, evaluate the advantages and disadvantages of this method of forming higher-efficiency tandem cells, and compare two- and three-terminal device configurations. APPROACH In

  2. Analysis of Web Based Solar Photovoltaic Mapping Tools

    Broader source: Energy.gov [DOE]

    A PV mapping tool visually represents a specific site and calculates PV system size and projected electricity production. This report identifies the commercially available solar mapping tools and thoroughly summarizes the source data type and resolution, the visualization software program being used, user inputs, calculation methodology and algorithms, map outputs, and development costs for each map.

  3. Fall 1994 wildlife and vegetation survey, Norton Air Force Base, California

    SciTech Connect (OSTI)

    Not Available

    1994-12-15

    The fall 1994 wildlife and vegetation surveys were completed October 3-7, 1994, at Norton Air Force Base (AFB), California. Two biologists from CDM Federal Programs, the U.S. Environmental Protection Agency (EPA) regional biologist and the Oak Ridge National Laboratory (ORNL) lead biologist conducted the surveys. A habitat assessment of three Installation Restoration Project (IRP) sites at Norton Air Force Base was also completed during the fall survey period. The IRP sites include: Landfill No. 2 (Site 2); the Industrial Wastewater Treatment Plant (IWTP) area; and Former Fire Training Area No. 1 (Site 5). The assessments were designed to qualitatively characterize the sites of concern, identify potential ecological receptors, and provide information for Remedial Design/Remedial Action activities. A Reference Area (Santa Ana River Wash) and the base urban areas were also characterized. The reference area assessment was performed to provide a baseline for comparison with the IRP site habitats. The fall 1994 survey is the second of up to four surveys that may be completed. In order to develop a complete understanding of all plant and animal species using the base, these surveys were planned to be conducted over four seasons. Species composition can vary widely during the course of a year in Southern California, and therefore, seasonal surveys will provide the most complete and reliable data to address changes in habitat structure and wildlife use of the site. Subsequent surveys will focus on seasonal wildlife observations and a spring vegetation survey.

  4. Hybrid Solar Cells with Prescribed Nanoscale Morphologies Based onHyperbranched Semiconductor Nanocrystals

    SciTech Connect (OSTI)

    Gur, Ilan; Fromer, Neil A.; Chen, Chih-Ping; Kanaras, AntoniosG.; Alivisatos, A. Paul

    2006-09-09

    In recent years, the search to develop large-area solar cells at low cost has led to research on photovoltaic (PV) systems based on nanocomposites containing conjugated polymers. These composite films can be synthesized and processed at lower costs and with greater versatility than the solid state inorganic semiconductors that comprise today's solar cells. However, the best nanocomposite solar cells are based on a complex architecture, consisting of a fine blend of interpenetrating and percolating donor and acceptor materials. Cell performance is strongly dependent on blend morphology, and solution-based fabrication techniques often result in uncontrolled and irreproducible blends, whose composite morphologies are difficult to characterize accurately. Here we incorporate 3-dimensional hyper-branched colloidal semiconductor nanocrystals in solution-processed hybrid organic-inorganic solar cells, yielding reproducible and controlled nanoscale morphology.

  5. EE Solar Energy Efficiency Solar | Open Energy Information

    Open Energy Info (EERE)

    EE Solar Energy Efficiency Solar Jump to: navigation, search Name: EE Solar (Energy Efficiency Solar) Place: Ponoma, California Zip: 91768 Product: PV systems installer based in...

  6. Operable Unit 1 remedial investigation report, Eielson Air Force Base, Alaska

    SciTech Connect (OSTI)

    Gilmore, T.J.; Fruland, R.M.; Liikala, T.L.

    1994-06-01

    This remedial investigation report for operable Unit 1 (OU-1) at Eielson Air Force Base presents data, calculations, and conclusions as to the nature and extent of surface and subsurface contamination at the eight source areas that make up OU-1. The information is based on the 1993 field investigation result and previous investigations. This report is the first in a set of three for OU-1. The other reports are the baseline risk assessment and feasibility study. The information in these reports will lead to a Record of Decision that will guide and conclude the environmental restoration effort for OU-1 at Eielson Air Force Base. The primary contaminants of concern include fuels and fuel-related contaminants (diesel; benzene, toluene, ethylbenzene, and xylene; total petroleum hydrocarbon; polycyclic aromatic hydrocarbons), maintenance-related solvents and cleaners (volatile chlorinated hydrocarbons such as trichloroothylene), polychlorinated biphenyls, and dichlorodiphenyltrichloroethane (DDT). The origins of contaminants of concern include leaks from storage tanks, drums and piping, and spills. Ongoing operations and past sitewide practices also contribute to contaminants of concern at OU-1 source areas. These include spraying mixed oil and solvent wastes on unpaved roads and aerial spraying of DDT.

  7. Vaillant Solar Systems | Open Energy Information

    Open Energy Info (EERE)

    Zip: 92075 Sector: Solar Product: California-based solar company specializing in solar water heating, solar pool heating and solar space heating systems for residential and...

  8. Environmental assessment: Warren Air Force Base 115-kV transmission line, Cheyenne, Wyoming

    SciTech Connect (OSTI)

    Not Available

    1986-03-01

    The Western Area Power Administration (Western), is propsoing to construct a new electrical tranmission line and substation in southeastern Wyoming. This proposed line, called the Warren Air Force Base Tranmission Line, will supply power for Western's system to Francis E.Warren Air Force Base (F.E. Warren AFB) near Cheyenne. It would allow for increased tranmission capacity to the air base. F.E. Warren AFB currently is served electrically be Western via a 13.8-kv line. It is a wood-pole, double-circuit line without an overhead ground wire, which extends from Western's Cheyenne Substation, through an urban area, and onto the air base. The Cheyenne Substation is located on the south side of the city of Cheyenne. The electrical load on the base is increasing from 4 megawatts (MW) to 11 or 12 MW, an approximate three-fold increase. Voltage problems occasionally occur at the base due to the present electrial loads and to the age and inadequacy of the 13.8-kv line, which was placed in service in 1941. The existing line has served beyond its designed service life and requires replacement. Replacement would be necessary even without an increasing load. F.E. Warren AFB has several new and expanding programs, including additional housing, shopping centers, and the Peacekeeper Missile Program. Part of this expansion already has occured; the remainder is expected by early 1988. This expansion has created the need for additional electrical service. The present 13.8-kV line is not capable of supporting the additional load. 28 refs., 4 figs., 2 tabs.

  9. Solar Reserve Methodology for Renewable Energy Integration Studies Based on Sub-Hourly Variability Analysis: Preprint

    SciTech Connect (OSTI)

    Ibanez, E.; Brinkman, G.; Hummon, M.; Lew, D.

    2012-08-01

    Increasing penetrations of wind a solar energy are raising concerns among electric system operators because of the variability and uncertainty associated with power sources. Previous work focused on the quantification of reserves for systems with wind power. This paper presents a new methodology that allows the determination of necessary reserves for high penetrations of photovoltaic (PV) power and compares it to the wind-based methodology. The solar reserve methodology is applied to Phase 2 of the Western Wind and Solar Integration Study. A summary of the results is included.

  10. Cross-Sectional Conductive Atomic Force Microscopy of CdTe/CdS Solar Cells: Effects of Etching and Back-Contact Processes; Preprint

    SciTech Connect (OSTI)

    Moutinho, H. R.; Dhere, R. G.; Jiang, C.-S.; Gessert, T. A.; Duda, A. M.; Young, M.; Metzger, W. K.; Li, X.; Al-Jassim, M. M.

    2006-05-01

    We investigated the effects of the etching processes using bromine and nitric-phosphoric acid solutions, as well as of Cu, in the bulk electrical conductivity of CdTe/CdS solar cells using conductive atomic force microscopy (C-AFM). Although the etching process can create a conductive layer on the surface of the CdTe, the layer is very shallow. In contrast, the addition of a thin layer of Cu to the surface creates a conductive layer inside the CdTe that is not uniform in depth, is concentrated at grains boundaries, and may short circuit the device if the CdTe is too thin. The etching process facilitates the Cu diffusion and results in thicker conductive layers. The existence of this inhomogeneous conductive layer directly affects the current transport and is probably the reason for needing thick CdTe in these devices.

  11. Eielson Air Force Base operable unit 2 and other areas record of decision

    SciTech Connect (OSTI)

    Lewis, R.E.; Smith, R.M.

    1994-10-01

    This decision document presents the selected remedial actions and no action decisions for Operable Unit 2 (OU2) at Eielson Air Force Base (AFB), Alaska, chosen in accordance with state and federal regulations. This document also presents the decision that no further action is required for 21 other source areas at Eielson AFB. This decision is based on the administrative record file for this site. OU2 addresses sites contaminated by leaks and spills of fuels. Soils contaminated with petroleum products occur at or near the source of contamination. Contaminated subsurface soil and groundwater occur in plumes on the top of a shallow groundwater table that fluctuates seasonally. These sites pose a risk to human health and the environment because of ingestion, inhalation, and dermal contact with contaminated groundwater. The purpose of this response is to prevent current or future exposure to the contaminated groundwater, to reduce further contaminant migration into the groundwater, and to remediate groundwater.

  12. Midtemperature solar systems test facility predictions for thermal performance based on test data. Polisolar Model POL solar collector with glass reflector surface

    SciTech Connect (OSTI)

    Harrison, T.D.

    1981-05-01

    Thermal performance predictions based on test data are presented for the Polisolar Model POL solar collector, with glass reflector surfaces, for three output temperatures at five cities in the United States.

  13. Midtemperature solar systems test facility predictions for thermal performance based on test data. Toltec two-axis tracking solar collector with 3M acrylic polyester film reflector surface

    SciTech Connect (OSTI)

    Harrison, T.D.

    1981-06-01

    Thermal performance predictions based on test data are presented for the Toltec solar collector, with acrylic film reflector surface, for three output temperatures at five cities in the United States.

  14. Graduating to a Bright Tomorrow: Solar Ready Vets Class Graduates from Hill

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFB | Department of Energy Graduating to a Bright Tomorrow: Solar Ready Vets Class Graduates from Hill AFB Graduating to a Bright Tomorrow: Solar Ready Vets Class Graduates from Hill AFB March 30, 2016 - 11:49am Addthis Deputy Secretary Liz Sherwood-Randall with the graduates of the Solar Ready Vets program at Hill Air Force Base, Utah. Image courtesy of the U.S. Air Force. Deputy Secretary Liz Sherwood-Randall with the graduates of the Solar Ready Vets program at Hill Air Force Base, Utah.

  15. A Supramolecular Complex in Small-Molecule Solar Cells based on Contorted

    Office of Scientific and Technical Information (OSTI)

    Aromatic Molecules (Journal Article) | SciTech Connect A Supramolecular Complex in Small-Molecule Solar Cells based on Contorted Aromatic Molecules Citation Details In-Document Search Title: A Supramolecular Complex in Small-Molecule Solar Cells based on Contorted Aromatic Molecules Authors: Kang S. ; Kim, J ; Chiu, C ; Ahn, S ; Schiros, T ; Lee, S ; Yager, K ; Toney, M ; Loo, Y ; Nuckolls, C Publication Date: 2012-08-20 OSTI Identifier: 1069683 Report Number(s): BNL--100255-2013-JA Journal

  16. Analysis of global radiation budgets and cloud forcing using three-dimensional cloud nephanalysis data base. Master's thesis

    SciTech Connect (OSTI)

    Mitchell, B.

    1990-12-01

    A one-dimensional radiative transfer model was used to compute the global radiative budget at the top of the atmosphere (TOA) and the surface for January and July. 1979. The model was also used to determine the global cloud radiative forcing for all clouds and for high and low cloud layers. In the computations. the authors used the monthly cloud data derived from the Air Force Three-Dimensional Cloud Nephanalysis (3DNEPH). These data were used in conjunction with conventional temperature and humidity profiles analyzed during the 1979 First GARP (Global Atmospheric Research Program) Global Experiment (FGGE) year. Global surface albedos were computed from available data and were included in the radiative transfer analysis. Comparisons of the model-produced outgoing solar and infrared fluxes with those derived from Nimbus 7 Earth Radiation Budget (ERS) data were made to validate the radiative model and cloud cover. For reflected solar and emitted infrared (IR) flux, differences within 20 w/sq m meters were shown.

  17. Vandenberg Air Force Base integrated resource assessment. Volume 2, Baseline detail

    SciTech Connect (OSTI)

    Halverson, M.A.; Richman, E.E.; Dagle, J.E.; Hickman, B.J.; Daellenbach, K.K.; Sullivan, G.P.

    1993-06-01

    The US Air Force Space Command has tasked the Pacific Northwest Laboratory, as the lead laboratory supporting the US Department of Energy Federal Energy Management Program, to identify, evaluate, and assist in acquiring all cost-effective energy projects at Vandenberg Air Force Base (VAFB). This is a model program PNL is designing for federal customers served by the Pacific Gas and Electric Company (PG and E). The primary goal of the VAFB project is to identify all electric energy efficiency opportunities, and to negotiate with PG and E to acquire those resources through a customized demand-side management program for its federal clients. That customized program should have three major characteristics: (1) 100% up-front financing; (2) substantial utility cost-sharing; and (3) utility implementation through energy service companies under contract to the utility. A similar arrangement will be pursued with Southern California Gas for non-electric resource opportunities if that is deemed desirable by the site and if the gas utility seems open to such an approach. This report documents the assessment of baseline energy use at VAFB located near Lompoc, California. It is a companion report to Volume 1, Executive Summary, and Volume 3, Resource Assessment. This analysis examines the characteristics of electric, natural gas, fuel oil, and propane use for fiscal year 1991. It records energy-use intensities for the facilities at VAFB by building type and energy end use. It also breaks down building energy consumption by fuel type, energy end use, and building type. A more complete energy consumption reconciliation is presented that includes the accounting of all energy use among buildings, utilities, and applicable losses.

  18. Griffiss Air Force Base integrated resource assessment. Volume 3, Electric resource assessment

    SciTech Connect (OSTI)

    Armstrong, P.R.; Shankle, S.A.; Elliott, D.B.; Stucky, D.J.; Keller, J.M.; Wahlstrom, R.R.; Dagle, J.E.; Gu, A.Y.

    1993-09-01

    The US Air Force Air Combat Command (ACC) has tasked the US Department of Energy (DOE) Federal Energy Management Program (FEMP) to identify, evaluate, and assist in acquiring all cost-effective energy projects at Griffiss Air Force Base (AFB). FEMP, with support from the Pacific Northwest Laboratory (PNL), is designing this model program for federal customers served by the Niagara Mohawk Power Company. The program with Griffiss AFB will (1) identify and evaluate all cost-effective electric energy projects; (2) develop a schedule for project acquisition considering project type, size, timing, capital requirements, as well as energy and dollar savings; and (3) secure 100% of the financing required to implement electric energy efficiency projects from Niagara Mohawk and have them procure the necessary contractors to perform detailed audits and install the technologies. This report provides the results of the electric energy resource opportunity (ERO) assessments performed by PNL at one of Niagara Mohawk`s primary federal facilities, the ACC Griffiss AFB facility located near Rome, New York. The results of the analyses of EROs are presented in seven common energy end-use categories. A narrative description of each ERO provides information on the initial cost, energy and dollar savings; impacts on operations and maintenance (O&M); and, when applicable, a discussion of energy supply and demand, energy security, and environmental issues. The evaluation methodology and technical and cost assumptions are also described for each ERO. Summary tables present the operational performance of energy end-use equipment before and after the implementation of each ERO and the results of the life-cycle cost analysis indicating the net present value (NPV) and savings-to-investment ratio (SIR) of each ERO.

  19. Midtemperature solar systems test faclity predictions for thermal performance based on test data: Solar Kinetics T-700 solar collector with glass reflector surface

    SciTech Connect (OSTI)

    Harrison, T.D.

    1981-03-01

    Sandia National Laboratories, Albuquerque (SNLA), is currently conducting a program to predict the performance and measure the characteristics of commercially available solar collectors that have the potential for use in industrial process heat and enhanced oil recovery applications. The thermal performance predictions for the Solar Kinetics solar line-focusing parabolic trough collector for five cities in the US are presented. (WHK)

  20. Sitewide biological risk assessment Eielson Air Force Base, Alaska: Risks to terrestrial receptors from diverse contaminants

    SciTech Connect (OSTI)

    Brandt, C.A.; Becker, J.M.

    1995-12-31

    Eielson Air Force Base (AFB) is located southeast of Fairbanks, Alaska. Eielson AFB was listed by the US Environmental Protection Agency on the National Priorities List with a total of 64 potential terrestrial and aquatic source areas. Contaminants of concern include fuel and fuel components, pesticides, polychlorinated biphenyls (PCBs), and lead. As part of the remedial investigations of these sites, a biological risk assessment (BRA) was conducted to estimate the risk of ecological effects on terrestrial receptors posed by contaminants in the Eielson environment. There are 32 mammal species, 117 bird species, 17 fish species, and 1 amphibian species known to inhabit Eielson AFB and vicinity. The BRA screened source areas based on completed biological exposure pathways, selected receptors for analysis, estimated exposure of receptors to contaminants, and compared these exposures to known toxicological effects. Lower Garrison Slough and Flightline Pond posed a substantial risk for shrikes and goshawks. Ingestion of PCBs constituted the primary pathway/contaminant combination contributing to this risk. The effects of the various sources of uncertainty in the ingestion exposure calculations for these sites were evaluated in a probabilistic risk assessment using Monte Carlo methods. There was an 11% risk of reproductive effects from PCBs for goshawks feeding from Flightline Pond and a 25 % risk from lower Garrison Slough. There was an 81 % risk of reproductive effects from PCB exposure for shrikes feeding near lower Garrison Slough.

  1. (Environmental investigation of ground water contamination at Wright-Patterson Air Force Base, Ohio)

    SciTech Connect (OSTI)

    Not Available

    1991-10-01

    In April 1990 Wright-Patterson Air Force Base (WPAFB) initiated an investigation to evaluate a potential CERCLA removal action to prevent, to the extent practicable, the migration of ground-water contamination in the Mad River Valley Aquifer within and across WPAFB boundaries. The action will be based on a Focused Feasibility Study with an Action Memorandum serving as a decision document that is subject to approval by the Ohio Environmental Protection Agency. The first phase (Phase 1) of this effort involves an investigation of ground-water contamination migrating across the southwest boundary of Area C and across Springfield Pike adjacent to Area B. Task 4 of Phase 1 is a field investigation to collect sufficient additional information to evaluate removal alternatives. The field investigation will provide information in the following specific areas of study: water-level data which will be used to permit calibration of the ground-water flow model to a unique time in history; and ground-water quality data which will be used to characterize the current chemical conditions of ground water.

  2. CASL - CFD-Based Turbulence Force Evaluation for Grid-to-Rod...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    light water reactors. GTRF is a complicated phenomenon, which includes flow excitation force, non-linear mechanical vibration, tribology, changing irradiated material properties...

  3. Source evaluation report phase 2 investigation: Limited field investigation. Final report: United States Air Force Environmental Restoration Program, Eielson Air Force Base, Alaska

    SciTech Connect (OSTI)

    Not Available

    1994-10-01

    This report describes the limited field investigation work done to address issues and answer unresolved questions regarding a collection of potential contaminant sources at Eielson Air Force Base (AFB), near Fairbanks, Alaska. These sources were listed in the Eielson AFB Federal Facility Agreement supporting the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) cleanup of the base. The limited field investigation began in 1993 to resolve all remaining technical issues and provide the data and analysis required to evaluate the environmental hazard associated with these sites. The objective of the limited field investigation was to allow the remedial project managers to sort each site into one of three categories: requiring remedial investigation/feasibility study, requiring interim removal action, or requiring no further remedial action.

  4. Sulfur Based Thermochemical Heat Storage for Baseload Concentrated Solar Power Generation

    SciTech Connect (OSTI)

    wong, bunsen

    2014-11-20

    This project investigates the engineering and economic feasibility of supplying baseload power using a concentrating solar power (CSP) plant integrated with sulfur based thermochemical heat storage. The technology stores high temperature solar heat in the chemical bonds of elemental sulfur. Energy is recovered as high temperature heat upon sulfur combustion. Extensive developmental and design work associated with sulfur dioxide (SO2) disproportionation and sulfuric acid (H2SO4) decomposition chemical reactions used in this technology had been carried out in the two completed phases of this project. The feasibility and economics of the proposed concept was demonstrated and determined.

  5. Compound Solar Technology CompSolar | Open Energy Information

    Open Energy Info (EERE)

    Solar Technology CompSolar Jump to: navigation, search Name: Compound Solar Technology (CompSolar) Place: Jhunan, Taiwan Zip: 350 Sector: Solar Product: Producer of glass-based...

  6. Silicon Valley Solar Inc SV Solar | Open Energy Information

    Open Energy Info (EERE)

    Solar Inc SV Solar Jump to: navigation, search Name: Silicon Valley Solar Inc (SV Solar) Place: Santa Clara, California Zip: 95051 Sector: Solar Product: A US-based manufacturer of...

  7. Balancing Autonomy and Utilization of Solar Power and Battery Storage for Demand Based Microgrids.

    SciTech Connect (OSTI)

    Lawder, Matthew T.; Viswanathan, Vilayanur V.; Subramanian, Venkat R.

    2015-04-01

    The growth of intermittent solar power has developed a need for energy storage systems in order to decouple generation and supply of energy. Microgrid (MG) systems comprising of solar arrays with battery energy storage studied in this paper desire high levels of autonomy, seeking to meet desired demand at all times. Large energy storage capacity is required for high levels of autonomy, but much of this expensive capacity goes unused for a majority of the year due to seasonal fluctuations of solar generation. In this paper, a model-based study of MGs comprised of solar generation and battery storage shows the relationship between system autonomy and battery utilization applied to multiple demand cases using a single particle battery model (SPM). The SPM allows for more accurate state-of-charge and utilization estimation of the battery than previous studies of renewably powered systems that have used empirical models. The increased accuracy of battery state estimation produces a better assessment of system performance. Battery utilization will depend on the amount of variation in solar insolation as well as the type of demand required by the MG. Consumers must balance autonomy and desired battery utilization of a system within the needs of their grid.

  8. (Environmental investigation of ground water contamination at Wright-Patterson Air Force Base, Ohio)

    SciTech Connect (OSTI)

    Thompson, Bill

    1991-10-01

    In April 1990, Wright-Patterson Air Force Base (WPAFB), initiated an investigation to evaluate a potential Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) removal action to prevent, to the extent practicable, the offsite migration of contaminated ground water from WPAFB. WPAFB retained the services of the Environmental Management Operations (EMO) and its principle subcontractor, International Technology Corporation (IT) to complete Phase 1 of the environmental investigation of ground-water contamination at WPAFB. Phase 1 of the investigation involves the short-term evaluation and potential design for a program to remove ground-water contamination that appears to be migrating across the western boundary of Area C, and across the northern boundary of Area B along Springfield Pike. Primarily, Task 4 of Phase 1 focuses on collection of information at the Area C and Springfield Pike boundaries of WPAFB. This Sampling and Analysis Plan (SAP) has been prepared to assist in completion of the Task 4 field investigation and is comprised of the Quality Assurance Project Plan (QAPP) and the Field Sampling Plan (FSP).

  9. Computational Intelligence Based Data Fusion Algorithm for Dynamic sEMG and Skeletal Muscle Force Modelling

    SciTech Connect (OSTI)

    Chandrasekhar Potluri,; Madhavi Anugolu; Marco P. Schoen; D. Subbaram Naidu

    2013-08-01

    In this work, an array of three surface Electrography (sEMG) sensors are used to acquired muscle extension and contraction signals for 18 healthy test subjects. The skeletal muscle force is estimated using the acquired sEMG signals and a Non-linear Wiener Hammerstein model, relating the two signals in a dynamic fashion. The model is obtained from using System Identification (SI) algorithm. The obtained force models for each sensor are fused using a proposed fuzzy logic concept with the intent to improve the force estimation accuracy and resilience to sensor failure or misalignment. For the fuzzy logic inference system, the sEMG entropy, the relative error, and the correlation of the force signals are considered for defining the membership functions. The proposed fusion algorithm yields an average of 92.49% correlation between the actual force and the overall estimated force output. In addition, the proposed fusionbased approach is implemented on a test platform. Experiments indicate an improvement in finger/hand force estimation.

  10. Baseline biological risk assessment for aquatic populations occurring near Eielson Air Force Base, Alaska

    SciTech Connect (OSTI)

    Dauble, D.; Brandt, C.; Lewis, R.; Smith, R.

    1995-12-31

    Eielson Air Force Base (AFB), Alaska was listed as a Superfund site in November 1989 with 64 potential source areas of contamination. As part of a sitewide remedial investigation, baseline risk assessments were conducted in 1993 and 1994 to evaluate hazards posed to biological receptors and to human health. Fish tissue, aquatic invertebrates, aquatic vegetation, sediment, and surface water data were collected from several on-site and off-site surface water bodies. An initial screening risk assessment indicated that several surface water sites along two major tributary creeks flowing through the base had unacceptable risks to both aquatic receptors and to human health because of DDTs. Other contaminants of concern (i.e., PCBs and PAHs) were below screening risk levels for aquatic organisms, but contributed to an unacceptable risk to human health. Additional samples was taken in 1994 to characterize the site-wide distribution of PAHs, DDTs, and PCBs in aquatic biota and sediments. Concentrations of PAHs were invertebrates > aquatic vegetation > fish, but concentrations were sufficiently low that they posed no significant risk to biological receptors. Pesticides were detected in all fish tissue samples. Polychlorinated biphenyls (PCBs) were also detected in most fish from Garrison Slough. The pattern of PCB concentrations in Arctic grayling (Thymallus arcticus) was related to their proximity to a sediment source in lower Garrison Slough. Ingestion of PCB-contaminated fish is the primary human-health risk driver for surface water bodies on Eielson AFB, resulting in carcinogenic risks > 1 {times} 10{sup {minus}4} for future recreational land-use at some sites. Principal considerations affecting uncertainty in the risk assessment process included spatial and temporal variability in media contaminant concentrations and inconsistencies between modelled and measured body burdens.

  11. Comparison of Historical Satellite-Based Estimates of Solar Radiation Resources with Recent Rotating Shadowband Radiometer Measurements: Preprint

    SciTech Connect (OSTI)

    Myers, D. R.

    2009-03-01

    The availability of rotating shadow band radiometer measurement data at several new stations provides an opportunity to compare historical satellite-based estimates of solar resources with measurements. We compare mean monthly daily total (MMDT) solar radiation data from eight years of NSRDB and 22 years of NASA hourly global horizontal and direct beam solar estimates with measured data from three stations, collected after the end of the available resource estimates.

  12. Midtemperature solar systems test facility predictions for thermal performance based on test data: solar kinetics T-600 solar collector with FEK 244 reflector surface

    SciTech Connect (OSTI)

    Harrison, T.D.

    1981-04-01

    Sandia National Laboratories, Albuquerque (SNLA), is currently conducting a program to predict the performance and measure the characteristics of commercially available solar collectors that have the potential for use in industrial process heat and enhanced oil recovery applications. The thermal performance predictions for the Solar Kinetics T-600 solar line-focusing parabolic trough collector are presented for three output temperatures at five cities in the US. (WHK)

  13. Geologic investigation :an update of subsurface geology on Kirtland Air Force Base, New Mexico.

    SciTech Connect (OSTI)

    Van Hart, Dirk

    2003-06-01

    The objective of this investigation was to generate a revised geologic model of Kirtland Air Force Base (KAFB) incorporating the geological and geophysical data produced since the Site-Wide Hydrogeologic Characterization Project (SWHC) of 1994 and 1995. Although this report has certain stand-alone characteristics, it is intended to complement the previous work and to serve as a status report as of late 2002. In the eastern portion of KAFB (Lurance Canyon and the Hubbell bench), of primary interest is the elevation to which bedrock is buried under a thin cap of alluvium. Elevation maps of the bedrock top reveal the paleodrainage that allows for the interpretation of the area's erosional history. The western portion of KAFB consists of the eastern part of the Albuquerque basin where bedrock is deeply buried under Santa Fe Group alluvium. In this area, the configuration of the down-to-the-west, basin-bounding Sandia and West Sandia faults is of primary interest. New geological and geophysical data and the reinterpretation of old data help to redefine the location and magnitude of these elements. Additional interests in this area are the internal stratigraphy and structure of the Santa Fe Group. Recent data collected from new monitoring wells in the area have led to a geologic characterization of the perched Tijeras Arroyo Groundwater system and have refined the known limits of the Ancestral Rio Grande fluvial sediments within the Santa Fe Group. Both the reinterpretation of the existing data and a review of the regional geology have shown that a segment of the boundary between the eastern and western portions of KAFB is a complicated early Tertiary (Laramide) wrench-fault system, the Tijeras/Explosive Ordnance Disposal Area/Hubbell Spring system. A portion of this fault zone is occupied by a coeval ''pull-apart'' basin filled with early Tertiary conglomerates, whose exposures form the ''Travertine Hills''.

  14. Havasu Solar Electric | Open Energy Information

    Open Energy Info (EERE)

    Havasu Solar Electric Jump to: navigation, search Name: Havasu Solar Electric Place: Arizona Zip: 86401 Sector: Solar Product: Arizona-based electric contractors in the solar...

  15. Acro Solar Lasers | Open Energy Information

    Open Energy Info (EERE)

    Acro Solar Lasers Place: El Paso, Texas Zip: 79936 Sector: Solar Product: Makes solar water heating devices based on parabolic dish concentrators. References: Acro Solar...

  16. Act Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    Solar Inc Jump to: navigation, search Name: Act Solar Inc. Place: Santa Clara, California Sector: Solar Product: California-based solar micro-inverter manufacturer and power...

  17. Crystal Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    Solar Inc Jump to: navigation, search Name: Crystal Solar Inc. Place: Santa Clara, California Zip: 94054 Sector: Solar Product: California-based developer of silicon solar cells....

  18. SolarHybrid AG | Open Energy Information

    Open Energy Info (EERE)

    SolarHybrid AG Jump to: navigation, search Name: SolarHybrid AG Place: Germany Sector: Solar Product: Germany-based solar thermal hybrid product manufacturer References:...

  19. Beijing Sijimicoe Solar Energy | Open Energy Information

    Open Energy Info (EERE)

    Sijimicoe Solar Energy Jump to: navigation, search Name: Beijing Sijimicoe Solar Energy Place: Beijing, China Zip: 102200 Sector: Solar Product: Beijing-based solar water heating...

  20. Matla Solar Energy | Open Energy Information

    Open Energy Info (EERE)

    Matla Solar Energy Jump to: navigation, search Name: Matla Solar Energy Place: East London, South Africa Sector: Solar Product: East London-based solar water geyser manufacturer....

  1. Everguard Solar Energy | Open Energy Information

    Open Energy Info (EERE)

    Everguard Solar Energy Jump to: navigation, search Name: Everguard Solar Energy Place: Albuquerque, New Mexico Zip: 87107 Sector: Solar Product: New Mexico-based solar PV electric...

  2. Eurostar Solar Energy ESE | Open Energy Information

    Open Energy Info (EERE)

    Eurostar Solar Energy ESE Jump to: navigation, search Name: Eurostar Solar Energy (ESE) Place: Dubai, United Arab Emirates Sector: Solar Product: Dubai-based PV module and solar...

  3. Merk Solar Energy | Open Energy Information

    Open Energy Info (EERE)

    Merk Solar Energy Jump to: navigation, search Name: Merk Solar Energy Place: Istanbul, Turkey Sector: Solar Product: Istanbul, Turkey based solar project developer. Coordinates:...

  4. Dynamic Worldwide Solar Energy | Open Energy Information

    Open Energy Info (EERE)

    Worldwide Solar Energy Jump to: navigation, search Name: Dynamic Worldwide Solar Energy Sector: Solar Product: US-based solar developer and financer. References: Dynamic Worldwide...

  5. RawSolar | Open Energy Information

    Open Energy Info (EERE)

    RawSolar Jump to: navigation, search Name: RawSolar Place: Berkeley, California Sector: Solar Product: California-based startup aiming to commercialise concentrating solar thermal...

  6. Aditya Solar Power Industries | Open Energy Information

    Open Energy Info (EERE)

    Aditya Solar Power Industries Jump to: navigation, search Name: Aditya Solar Power Industries Place: India Sector: Solar Product: Bangalore-based solar project developer....

  7. Clover Solar Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    Clover Solar Pvt Ltd Jump to: navigation, search Name: Clover Solar Pvt. Ltd. Place: Mumbai, Maharashtra, India Zip: 400021 Sector: Solar Product: Mumbai-based solar project...

  8. Solar Brain Srl | Open Energy Information

    Open Energy Info (EERE)

    Brain Srl Jump to: navigation, search Name: Solar Brain Srl Place: Rome, Italy Zip: 189 Sector: Solar Product: Rome-based solar and alternative energy company. References: Solar...

  9. Avalon Solar LLC | Open Energy Information

    Open Energy Info (EERE)

    Avalon Solar LLC Jump to: navigation, search Name: Avalon Solar LLC Place: Albuquerque, New Mexico Zip: 87123 Sector: Solar Product: Albuquerque-based solar project developer....

  10. Daelim Solar Co Ltd | Open Energy Information

    Open Energy Info (EERE)

    search Name: Daelim Solar Co Ltd Place: Korea (Republic) Sector: Solar Product: South Korea-based solar heating systems manufacturer. References: Daelim Solar Co Ltd1...

  11. Skypoint Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    Name: Skypoint Solar Inc. Place: Vermont Zip: 5255 Sector: Solar Product: Vermont based solar panel manufacturing company that will also be involved in the establishment of solar...

  12. Green Solar Finance | Open Energy Information

    Open Energy Info (EERE)

    Solar Finance Jump to: navigation, search Name: Green Solar Finance Place: Connecticut Sector: Solar Product: Connecticut-based arranger of financing for clients of solar project...

  13. Sequoia Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    search Name: Sequoia Solar, Inc. Place: Solana Beach, California Zip: 92075 Sector: Solar Product: California-based installer of solar plants. References: Sequoia Solar,...

  14. Two-Dimensional Measurement of n+-p Asymmetrical Junctions in Multicrystalline Silicon Solar Cells using AFM-Based Electrical Techniques with Nanometer Resolution

    SciTech Connect (OSTI)

    Jiang, C. S.; Heath, J. T.; Moutinho, H. R.; Li, J. V.; Al-Jassim, M. M.

    2011-01-01

    Lateral inhomogeneities of modern solar cells demand direct electrical imaging with nanometer resolution. We show that atomic force microscopy (AFM)-based electrical techniques provide unique junction characterizations, giving a two-dimensional determination of junction locations. Two AFM-based techniques, scanning capacitance microscopy/spectroscopy (SCM/SCS) and scanning Kelvin probe force microscopy (SKPFM), were significantly improved and applied to the junction characterizations of multicrystalline silicon (mc-Si) cells. The SCS spectra were taken pixel by pixel by precisely controlling the tip positions in the junction area. The spectra reveal distinctive features that depend closely on the position relative to the electrical junction, which allows us to indentify the electrical junction location. In addition, SKPFM directly probes the built-in potential over the junction area modified by the surface band bending, which allows us to deduce the metallurgical junction location by identifying a peak of the electric field. Our results demonstrate resolutions of 10-40 nm, depending on the techniques (SCS or SKPFM). These direct electrical measurements with nanometer resolution and intrinsic two-dimensional capability are well suited for investigating the junction distribution of solar cells with lateral inhomogeneities.

  15. Two-Dimensional Measurement of n+-p Asymmetrical Junctions in Multicrystalline Silicon Solar Cells Using AFM-Based Electrical Techniques with Nanometer Resolution: Preprint

    SciTech Connect (OSTI)

    Jiang, C. S.; Moutinho, H. R.; Li, J. V.; Al-Jassim, M. M.; Heath, J. T.

    2011-07-01

    Lateral inhomogeneities of modern solar cells demand direct electrical imaging with nanometer resolution. We show that atomic force microscopy (AFM)-based electrical techniques provide unique junction characterizations, giving a two-dimensional determination of junction locations. Two AFM-based techniques, scanning capacitance microscopy/spectroscopy (SCM/SCS) and scanning Kelvin probe force microscopy (SKPFM), were significantly improved and applied to the junction characterizations of multicrystalline silicon (mc-Si) cells. The SCS spectra were taken pixel by pixel by precisely controlling the tip positions in the junction area. The spectra reveal distinctive features that depend closely on the position relative to the electrical junction, which allows us to indentify the electrical junction location. In addition, SKPFM directly probes the built-in potential over the junction area modified by the surface band bending, which allows us to deduce the metallurgical junction location by identifying a peak of the electric field. Our results demonstrate resolutions of 10-40 nm, depending on the techniques (SCS or SKPFM). These direct electrical measurements with nanometer resolution and intrinsic two-dimensional capability are well suited for investigating the junction distribution of solar cells with lateral inhomogeneities.

  16. A comparison of data from SOLMET/ERSATZ and the National Solar Radiation Data Base

    SciTech Connect (OSTI)

    Marion, W.; Myers, D.

    1992-11-01

    This report compares data from the new National Solar Radiation Data Base (NSRDB) with data from the earlier SOLMET/ERSATZ data base. It compares the two data bases, station-by-station, with respect to their long-term average daily values of global horizontal and direct normal solar radiation. We conclude that on an annual basis, NSRDB values for global horizontal radiation are within {plus_minus}5% of SOLMET/ERSATZ values for 60% of the stations, more than 5% greater than the SOLMET/ERSATZ values for 30% of the stations, and more than 5% less than the SOLMET/ERSATZ values for 10% of the stations. On an annual basis for direct nominal radiation, the NSRDB values are with {plus_minus}5% of the SOLMET/ERSATZ data for only 40% of the stations, more than 5% greater than the SOLMET/ERSATZ values for 45% of the stations, and more than 5% less than the SOLMET/ERSATZ values for 15% of the stations. In general, the NSRDB shows higher values of solar radiation for the eastern United States, particularly the Northeast, and lower values for some of the western states (Arizona, Colorado, Idaho, Nevada, New Mexico, Utah, and Wyoming). However, because some of the stations within a state show higher values of solar radiation while others show lower values, this generalization may be misleading when concerned with a particular station. Consequently, the appendices provide tables showing a station-by-station comparison of the NSRDB and SOLMET/ERSATZ data. In addition to comparing annual values, the tables compare the two data bases for the months of August and December. This comparison shows larger differences between the two data bases for December.

  17. Paz Solar | Open Energy Information

    Open Energy Info (EERE)

    Paz Solar Jump to: navigation, search Name: Paz Solar Place: Israel Product: Israel-based engineering and installation contractor. References: Paz Solar1 This article is a stub....

  18. Solar Mimizan | Open Energy Information

    Open Energy Info (EERE)

    Mimizan Jump to: navigation, search Name: Solar Mimizan Place: PARIS, France Zip: 75002 Sector: Solar Product: Paris-based, building-integrated solar power plant developer....

  19. Solar Wind | Open Energy Information

    Open Energy Info (EERE)

    Wind Jump to: navigation, search Name: Solar Wind Place: Krasnodar, Romania Zip: 350000 Sector: Solar, Wind energy Product: Russia-based PV product manufacturer. Solar Wind...

  20. Solar Technologies | Open Energy Information

    Open Energy Info (EERE)

    Place: Dubai, United Arab Emirates Sector: Solar Product: Dubai-based solar photovoltaic module manufacturing company. References: Solar Technologies1 This article is a...

  1. Solar-energy conversion by combined photovoltaic converters with CdTe and CuInSe{sub 2} base layers

    SciTech Connect (OSTI)

    Khrypunov, G. S. Sokol, E. I.; Yakimenko, Yu. I.; Meriuts, A. V.; Ivashuk, A. V.; Shelest, T. N.

    2014-12-15

    The possibility of the combined use of bifacial thin-film solar cells based on CdTe and frontal solar cells with a CuInSe{sub 2} base layer in tandem structures is experimentally confirmed. It is found that, for the use of bifacial solar cells based on cadmium telluride in a tandem structure, the optimal thickness of their base layer should be 1 ?m. The gain in the efficiency of the tandem structure, compared with an individual CuInSe{sub 2}-based solar cell, is 1.8% in the case of series-connected solar cells and 1.3%, for parallel-connected.

  2. Liquid-phase-deposited siloxane-based capping layers for silicon solar cells

    SciTech Connect (OSTI)

    Veith-Wolf, Boris; Wang, Jianhui; Hannu-Kuure, Milja; Chen, Ning; Hadzic, Admir; Williams, Paul; Leivo, Jarkko; Karkkainen, Ari; Schmidt, Jan

    2015-02-02

    We apply non-vacuum processing to deposit dielectric capping layers on top of ultrathin atomic-layer-deposited aluminum oxide (AlO{sub x}) films, used for the rear surface passivation of high-efficiency crystalline silicon solar cells. We examine various siloxane-based liquid-phase-deposited (LPD) materials. Our optimized AlO{sub x}/LPD stacks show an excellent thermal and chemical stability against aluminum metal paste, as demonstrated by measured surface recombination velocities below 10 cm/s on 1.3 Ωcm p-type silicon wafers after firing in a belt-line furnace with screen-printed aluminum paste on top. Implementation of the optimized LPD layers into an industrial-type screen-printing solar cell process results in energy conversion efficiencies of up to 19.8% on p-type Czochralski silicon.

  3. High-speed atomic force microscope based on an astigmatic detection system

    SciTech Connect (OSTI)

    Liao, H.-S.; Chen, Y.-H.; Hwu, E.-T.; Chang, C.-S.; Hwang, I.-S.; Ding, R.-F.; Huang, H.-F.; Wang, W.-M.; Huang, K.-Y.

    2014-10-15

    High-speed atomic force microscopy (HS-AFM) enables visualizing dynamic behaviors of biological molecules under physiological conditions at a temporal resolution of 1s or shorter. A small cantilever with a high resonance frequency is crucial in increasing the scan speed. However, detecting mechanical resonances of small cantilevers is technically challenging. In this study, we constructed an atomic force microscope using a digital versatile disc (DVD) pickup head to detect cantilever deflections. In addition, a flexure-guided scanner and a sinusoidal scan method were implemented. In this work, we imaged a grating sample in air by using a regular cantilever and a small cantilever with a resonance frequency of 5.5 MHz. Poor tracking was seen at the scan rate of 50 line/s when a cantilever for regular AFM imaging was used. Using a small cantilever at the scan rate of 100 line/s revealed no significant degradation in the topographic images. The results indicate that a smaller cantilever can achieve a higher scan rate and superior force sensitivity. This work shows the potential for using a DVD pickup head in future HS-AFM technology.

  4. Narrowband filter radiometer for ground-based measurements of global ultraviolet solar irradiance and total ozone

    SciTech Connect (OSTI)

    Petkov, Boyan; Vitale, Vito; Tomasi, Claudio; Bonafe, Ubaldo; Scaglione, Salvatore; Flori, Daniele; Santaguida, Riccardo; Gausa, Michael; Hansen, Georg; Colombo, Tiziano

    2006-06-20

    The ultraviolet narrowband filter radiometer (UV-RAD) designed by the authors to take ground-based measurements of UV solar irradiance, total ozone, and biological dose rate is described, together with the main characteristics of the seven blocked filters mounted on it, all of which have full widths at half maxima that range 0.67 to 0.98 nm. We have analyzed the causes of cosine response and calibration errors carefully to define the corresponding correction terms, paying particular attention to those that are due to the spectral displacements of the filter transmittance peaks from the integer wavelength values. The influence of the ozone profile on the retrieved ozone at large solar zenith angles has also been examined by means of field measurements. The opportunity of carrying out nearly monochromatic irradiance measurements offered by the UV-RAD allowed us to improve the procedure usually followed to reconstruct the solar spectrum at the surface by fitting the computed results, using radiative transfer models with field measurements of irradiance. Two long-term comparison campaigns took place, showing that a mean discrepancy of+0.3% exists between the UV-RAD total ozone values and those given by the Brewer no. 63 spectroradiometer and that mean differences of+0.3% and-0.9% exist between the erythemal dose rates determined with the UV-RAD and those obtained with the Brewer no. 63 and the Brewer no. 104 spectroradiometers, respectively.

  5. Sandia Energy - Air Force Research Laboratory Testing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    from the Air Force Research Laboratory in Albuquerque utilized the site at the National Solar Thermal Test Facility to evaluate seismic and optical activity from explosives set...

  6. Sandia Energy - Air Force Research Laboratory Testing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the Air Force Research Laboratory (AFRL) in Albuquerque utilized the site at the National Solar Thermal Test Facility (NSTTF) to evaluate seismic and optical activity from...

  7. Weardale Task Force | Open Energy Information

    Open Energy Info (EERE)

    that is developing a sustainable community in the East gate area which will be run on wind, solar, biomass, geothermal and hydro power. References: Weardale Task Force1...

  8. High efficiency thin film CdTe and a-Si based solar cells

    SciTech Connect (OSTI)

    Compaan, A. D.; Deng, X.; Bohn, R. G.

    2000-01-04

    This report describes work done by the University of Toledo during the first year of this subcontract. During this time, the CdTe group constructed a second dual magnetron sputter deposition facility; optimized reactive sputtering for ZnTe:N films to achieve 10 ohm-cm resistivity and {approximately}9% efficiency cells with a copper-free ZnTe:N/Ni contact; identified Cu-related photoluminescence features and studied their correlation with cell performance including their dependence on temperature and E-fields; studied band-tail absorption in CdS{sub x}Te{sub 1{minus}x} films at 10 K and 300 K; collaborated with the National CdTe PV Team on (1) studies of high-resistivity tin oxide (HRT) layers from ITN Energy Systems, (2) fabrication of cells on the HRT layers with 0, 300, and 800-nm CdS, and (3) preparation of ZnTe:N-based contacts on First Solar materials for stress testing; and collaborated with Brooklyn College for ellipsometry studies of CdS{sub x}Te{sub 1{minus}x} alloy films, and with the University of Buffalo/Brookhaven NSLS for synchrotron X-ray fluorescence studies of interdiffusion in CdS/CdTe bilayers. The a-Si group established a baseline for fabricating a-Si-based solar cells with single, tandem, and triple-junction structures; fabricated a-Si/a-SiGe/a-SiGe triple-junction solar cells with an initial efficiency of 9.7% during the second quarter, and 10.6% during the fourth quarter (after 1166 hours of light-soaking under 1-sun light intensity at 50 C, the 10.6% solar cells stabilized at about 9%); fabricated wide-bandgap a-Si top cells, the highest Voc achieved for the single-junction top cell was 1.02 V, and top cells with high FF (up to 74%) were fabricated routinely; fabricated high-quality narrow-bandgap a-SiGe solar cells with 8.3% efficiency; found that bandgap-graded buffer layers improve the performance (Voc and FF) of the narrow-bandgap a-SiGe bottom cells; and found that a small amount of oxygen partial pressure ({approximately}2 {times} 10{sup {minus}5} torr) was beneficial for growing high-quality films from ITO targets.

  9. Mapping of Proteomic Composition on the Surfaces of Bacillus spores by Atomic Force Microscopy-based Immunolabeling

    SciTech Connect (OSTI)

    Plomp, M; Malkin, A J

    2008-06-02

    Atomic force microscopy provides a unique capability to image high-resolution architecture and structural dynamics of pathogens (e.g. viruses, bacteria and bacterial spores) at near molecular resolution in native conditions. Further development of atomic force microscopy in order to enable the correlation of pathogen protein surface structures with specific gene products is essential to understand the mechanisms of the pathogen life cycle. We have applied an AFM-based immunolabeling technique for the proteomic mapping of macromolecular structures through the visualization of the binding of antibodies, conjugated with nanogold particles, to specific epitopes on Bacillus spore surfaces. This information is generated while simultaneously acquiring the surface morphology of the pathogen. The immunospecificity of this labeling method was established through the utilization of specific polyclonal and monoclonal antibodies that target spore coat and exosporium epitopes of Bacillus atrophaeus and Bacillus anthracis spores.

  10. Midtemperature solar systems test facility predictions for thermal performance based on test data: Sun-Heet nontracking solar collector

    SciTech Connect (OSTI)

    Harrison, T.D.

    1981-03-01

    Sandia National Laboratories, Albuquerque (SNLA), is currently conducting a program to predict the performance and measure the characteristics of commercially available solar collectors that have the potential for use in industrial process heat and enhanced oil recovery applications. The thermal performance predictions for the Sun-Heet nontracking, line-focusing parabolic trough collector at five cities in the US are presented. (WHK)

  11. Luminescence based series resistance mapping of III-V multijunction solar cells

    SciTech Connect (OSTI)

    Nesswetter, Helmut; Dyck, Wilhelm; Lugli, Paolo; Bett, Andreas W.; Zimmermann, Claus G.

    2013-11-21

    A method to measure the series resistance of Ga{sub 0.5}In{sub 0.5}P/Ga(In)As/Ge triple-junction solar cells spatially resolved is developed, based on luminescence imaging. With the help of network simulations, the dependence of the local series resistance on the external subcell illumination intensities and biasing voltage is predicted and the optimum measurement conditions are clarified. Experimentally, specially prepared test cells with partially irradiated areas are used to verify the capabilities of the method. It is shown that the method is not sensitive to variations of the dark IV parameters of the subcells.

  12. EVOLUTION OF A MAGNETIC FLUX ROPE AND ITS OVERLYING ARCADE BASED ON NONLINEAR FORCE-FREE FIELD EXTRAPOLATIONS

    SciTech Connect (OSTI)

    Jing, Ju; Liu, Chang; Lee, Jeongwoo; Wang, Shuo; Xu, Yan; Wang, Haimin; Wiegelmann, Thomas

    2014-03-20

    Dynamic phenomena indicative of slipping reconnection and magnetic implosion were found in a time series of nonlinear force-free field (NLFFF) extrapolations for the active region 11515, which underwent significant changes in the photospheric fields and produced five C-class flares and one M-class flare over five hours on 2012 July 2. NLFFF extrapolation was performed for the uninterrupted 5 hour period from the 12 minute cadence vector magnetograms of the Helioseismic and Magnetic Imager on board the Solar Dynamic Observatory. According to the time-dependent NLFFF model, there was an elongated, highly sheared magnetic flux rope structure that aligns well with an Hα filament. This long filament splits sideways into two shorter segments, which further separate from each other over time at a speed of 1-4 km s{sup –1}, much faster than that of the footpoint motion of the magnetic field. During the separation, the magnetic arcade arching over the initial flux rope significantly decreases in height from ∼4.5 Mm to less than 0.5 Mm. We discuss the reality of this modeled magnetic restructuring by relating it to the observations of the magnetic cancellation, flares, a filament eruption, a penumbra formation, and magnetic flows around the magnetic polarity inversion line.

  13. Solar Dynamics | Open Energy Information

    Open Energy Info (EERE)

    Dynamics Jump to: navigation, search Name: Solar Dynamics Place: Ottumwa, Iowa Zip: IA 52501 Sector: Solar Product: Solar Dynamics is a US-based solar powered attic roof vents...

  14. Capital Solar | Open Energy Information

    Open Energy Info (EERE)

    Solar Jump to: navigation, search Name: Capital Solar Place: Lecce, Italy Sector: Solar Product: Lecce-based solar project developer. Coordinates: 40.357955, 18.16801 Show Map...

  15. ISI Solar | Open Energy Information

    Open Energy Info (EERE)

    ISI Solar Jump to: navigation, search Name: ISI Solar Place: New City, New York Zip: 10956 Sector: Solar Product: US-based company that designs and installs solar power systems for...

  16. Performance optimization of solar cells based on colloidal lead sulfide nanocrystals

    SciTech Connect (OSTI)

    Ulfa, Maria

    2014-02-24

    Colloidal semiconducting quantum dot nanocrystals (NCs) have attracted extensive interest as active building-block for low-cost solution-processed photovoltaic due to their size tunable absorption from the visible to near IR. Among various nanocrystal composition, lead sulfide (PbS), having a bulk bandgap of 0.41 eV, are particularly attractive for photovoltaic applications due to their excellent photosensitivity in the near IR. Starting from colloidal synthesis, in this project functional solar cells are fabricated and characterized based on the nearly monodispersed colloidal PbS nanocrystals that we synthesized. These NC-solar cells are fabricated under a “depleted heterojunction” device architecture containing a planar “tipe II” heretojunction formed by a layer of electron-transporting TiO{sub 2} and a layer of PbS NCs. Relevant structural, optical, and electrical characterizations are performed on NCs and their devices. To understand the operational mechanism of these NC-based solar cells, various material and device aspects are investigated in this work aiming for optimized photovoltaic performance. These aspects include the effect of: (1) NC dimensions (and thus their band gaps); (2) passivation of surface traps through post-synthesis treatments; (3) NC surface ligand-exchange; and (4) interfacial modifications at the heterojunction. The most optimized photovoltaic performance is found after combining the surface trap passivation strategy by halides, ligand-exchange by 3-mercaptopropionic acids, and interfacial TiCl4 treatment, leading to a peak open-circuit voltage of 0.53 V, a short-circuit current density of 14.03 mAcm{sup −2}, and a power conversion efficiency of 3.25%.

  17. Photovoltaic solar concentrator

    DOE Patents [OSTI]

    Nielson, Gregory N.; Cruz-Campa, Jose Luis; Okandan, Murat; Resnick, Paul J.; Sanchez, Carlos Anthony; Clews, Peggy J.; Gupta, Vipin P.

    2015-09-08

    A process including forming a photovoltaic solar cell on a substrate, the photovoltaic solar cell comprising an anchor positioned between the photovoltaic solar cell and the substrate to suspend the photovoltaic solar cell from the substrate. A surface of the photovoltaic solar cell opposite the substrate is attached to a receiving substrate. The receiving substrate may be bonded to the photovoltaic solar cell using an adhesive force or a metal connecting member. The photovoltaic solar cell is then detached from the substrate by lifting the receiving substrate having the photovoltaic solar cell attached thereto and severing the anchor connecting the photovoltaic solar cell to the substrate. Depending upon the type of receiving substrate used, the photovoltaic solar cell may be removed from the receiving substrate or remain on the receiving substrate for use in the final product.

  18. CVD-Based Valence-Mending Passivation for Crystalline-Si Solar Cells

    SciTech Connect (OSTI)

    Tao, Meng

    2015-03-01

    The objective of this project is to investigate a new surface passivation technique, valence-mending passivation, for its applications in crystalline-Si solar cells to achieve significant efficiency improvement and cost reduction. As the enabling technique, the project includes the development of chemical vapor deposition recipes to passivate textured Si(100) and multicrystalline-Si surfaces by sulfur and the characterization of the passivated Si surfaces, including thermal stability, Schottky barrier height, contact resistance and surface recombination. One important application is to replace the Ag finger electrode in Si cells with Al to reduce cost, by ~$0.1/Wp, and allow terawatt-scale deployment of crystalline-Si solar cells. These all-Al Si cells require a low-temperature metallization process for the Al electrode, to be compatible with valence-mending passivation and to prevent Al diffusion into n-type Si. Another application is to explore valence-mending passivation of grain boundaries in multicrystalline Si by diffusing sulfur into grain boundaries, to reduce the efficiency gas between monocrystalline-Si solar cells and multicrystalline-Si cells. The major accomplishments of this project include: 1) Demonstration of chemical vapor deposition processes for valence-mending passivation of both monocrystalline Si(100) and multicrystalline Si surfaces. Record Schottky barriers have been demonstrated, with the new record-low barrier of less than 0.08 eV between Al and sulfur-passivated n-type Si(100) and the new record-high barrier of 1.14 eV between Al and sulfur-passivated p-type Si(100). On the textured p-type monocrystalline Si(100) surface, the highest barrier with Al is 0.85 eV by valence-mending passivation. 2) Demonstration of a low-temperature metallization process for Al in crystalline-Si solar cells. The new metallization process is based on electroplating of Al in a room-temperature ionic liquid. The resistivity of the electroplated Al is ~7×10–6 ohm-cm, similar to that of screen-printed Ag. 3) Demonstration of two all-Al, Ag-free Si solar cells, with an electroplated Al front electrode and a screen-printed Al back electrode. One cell is an industrial p-type front-emitter cell, and the other is an n-type back-emitter cell. The efficiency of the p-type cell is close to 15%. This is an industrial cell and its efficiency is capped at ~18%. 4) Demonstration of grain boundary passivation by both hydrogen and sulfur using hydrogen sulfide (H2S). When the new grain boundary passivation is combined with Al2O3 surface passivation and post-annealing, the minority carrier lifetime in the p-type multicrystalline Si samples shows a significant improvement up to 68 fold. 5) In a side project, a simple green process is developed which is capable of recycling over 90% of the Si material in end-of-life crystalline-Si solar cells. The recycled Si meets the specifications for solar-grade Si and can be used as a new poly-Si feedstock for ingot growth.

  19. High Efficiency Solar-based Catalytic Structure for CO{sub 2} Reforming

    SciTech Connect (OSTI)

    Menkara, Hisham

    2013-09-30

    Throughout this project, we developed and optimized various photocatalyst structures for CO{sub 2} reforming into hydrocarbon fuels and various commodity chemical products. We also built several closed-loop and continuous fixed-bed photocatalytic reactor system prototypes for a larger-scale demonstration of CO{sub 2} reforming into hydrocarbons, mainly methane and formic acid. The results achieved have indicated that with each type of reactor and structure, high reforming yields can be obtained by refining the structural and operational conditions of the reactor, as well as by using various sacrificial agents (hole scavengers). We have also demonstrated, for the first time, that an aqueous solution containing acid whey (a common bio waste) is a highly effective hole scavenger for a solar-based photocatalytic reactor system and can help reform CO{sub 2} into several products at once. The optimization tasks performed throughout the project have resulted in efficiency increase in our conventional reactors from an initial 0.02% to about 0.25%, which is 10X higher than our original project goal. When acid whey was used as a sacrificial agent, the achieved energy efficiency for formic acid alone was ~0.4%, which is 16X that of our original project goal and higher than anything ever reported for a solar-based photocatalytic reactor. Therefore, by carefully selecting sacrificial agents, it should be possible to reach energy efficiency in the range of the photosynthetic efficiency of typical crop and biofuel plants (1-3%).

  20. Breakout Session: Solar as a Base Load Power Source | Department of Energy

    Office of Environmental Management (EM)

    Pitch for Solar Breakout Session: Pitch for Solar May 21, 2014 5:15PM to 7:30PM PDT San Simeon A & B As the hardware costs of solar have decreased significantly over the last decade, the non-hardware "soft costs" of solar - like permitting, installation, financing, and grid integration, among others - remain a major barrier to greater solar deployment in the U.S. and make up an increasingly larger fraction of the total cost of a solar energy system. SunShot invites big thinkers,

  1. A solar thermal cooling and heating system for a building: Experimental and model based performance analysis and design

    SciTech Connect (OSTI)

    Qu, Ming; Yin, Hongxi; Archer, David H.

    2010-02-15

    A solar thermal cooling and heating system at Carnegie Mellon University was studied through its design, installation, modeling, and evaluation to deal with the question of how solar energy might most effectively be used in supplying energy for the operation of a building. This solar cooling and heating system incorporates 52 m{sup 2} of linear parabolic trough solar collectors; a 16 kW double effect, water-lithium bromide (LiBr) absorption chiller, and a heat recovery heat exchanger with their circulation pumps and control valves. It generates chilled and heated water, dependent on the season, for space cooling and heating. This system is the smallest high temperature solar cooling system in the world. Till now, only this system of the kind has been successfully operated for more than one year. Performance of the system has been tested and the measured data were used to verify system performance models developed in the TRaNsient SYstem Simulation program (TRNSYS). On the basis of the installed solar system, base case performance models were programmed; and then they were modified and extended to investigate measures for improving system performance. The measures included changes in the area and orientation of the solar collectors, the inclusion of thermal storage in the system, changes in the pipe diameter and length, and various system operational control strategies. It was found that this solar thermal system could potentially supply 39% of cooling and 20% of heating energy for this building space in Pittsburgh, PA, if it included a properly sized storage tank and short, low diameter connecting pipes. Guidelines for the design and operation of an efficient and effective solar cooling and heating system for a given building space have been provided. (author)

  2. Compensation of Wave-Induced Motion and Force Phenomena for Ship-Based High Performance Robotic and Human Amplifying Systems

    SciTech Connect (OSTI)

    Love, LJL

    2003-09-24

    The decrease in manpower and increase in material handling needs on many Naval vessels provides the motivation to explore the modeling and control of Naval robotic and robotic assistive devices. This report addresses the design, modeling, control and analysis of position and force controlled robotic systems operating on the deck of a moving ship. First we provide background information that quantifies the motion of the ship, both in terms of frequency and amplitude. We then formulate the motion of the ship in terms of homogeneous transforms. This transformation provides a link between the motion of the ship and the base of a manipulator. We model the kinematics of a manipulator as a serial extension of the ship motion. We then show how to use these transforms to formulate the kinetic and potential energy of a general, multi-degree of freedom manipulator moving on a ship. As a demonstration, we consider two examples: a one degree-of-freedom system experiencing three sea states operating in a plane to verify the methodology and a 3 degree of freedom system experiencing all six degrees of ship motion to illustrate the ease of computation and complexity of the solution. The first series of simulations explore the impact wave motion has on tracking performance of a position controlled robot. We provide a preliminary comparison between conventional linear control and Repetitive Learning Control (RLC) and show how fixed time delay RLC breaks down due to the varying nature wave disturbance frequency. Next, we explore the impact wave motion disturbances have on Human Amplification Technology (HAT). We begin with a description of the traditional HAT control methodology. Simulations show that the motion of the base of the robot, due to ship motion, generates disturbances forces reflected to the operator that significantly degrade the positioning accuracy and resolution at higher sea states. As with position-controlled manipulators, augmenting the control with a Repetitive Learning Controller has little impact due to the variable nature of the wave period. We then introduce a new approach to HAT control, Ship Motion Compensation for Force Control Systems (SMCFCS). This basic approach uses inclinometer and acceleration information from the base of the robot to compensate for ship motion disturbances. Results of the simulation study show over an order of magnitude decrease in the disturbance force reflected back to the operator and an order of magnitude increase in positioning accuracy and resolution.

  3. InGaN-based thin film solar cells: Epitaxy, structural design, and photovoltaic properties

    SciTech Connect (OSTI)

    Sang, Liwen; Liao, Meiyong; Koide, Yasuo; Sumiya, Masatomo

    2015-03-14

    In{sub x}Ga{sub 1−x}N, with the tunable direct bandgaps from ultraviolet to near infrared region, offers a promising candidate for the high-efficiency next-generation thin-film photovoltaic applications. Although the adoption of thick InGaN film as the active region is desirable to obtain efficient light absorption and carrier collection compared to InGaN/GaN quantum wells structure, the understanding on the effect from structural design is still unclear due to the poor-quality InGaN films with thickness and difficulty of p-type doping. In this paper, we comprehensively investigate the effects from film epitaxy, doping, and device structural design on the performances of the InGaN-based solar cells. The high-quality InGaN thick film is obtained on AlN/sapphire template, and p-In{sub 0.08}Ga{sub 0.92}N is achieved with a high hole concentration of more than 10{sup 18 }cm{sup −3}. The dependence of the photovoltaic performances on different structures, such as active regions and p-type regions is analyzed with respect to the carrier transport mechanism in the dark and under illumination. The strategy of improving the p-i interface by using a super-thin AlN interlayer is provided, which successfully enhances the performance of the solar cells.

  4. Characterization and remediation of 91B radioactive waste sites under performance based contracts at Lackland Air Force Base, San Antonio, Texas

    SciTech Connect (OSTI)

    Trujillo, P.A.; Anderson, K.D.

    2007-07-01

    This paper describes the challenges behind the implementation of the characterization, remediation, and the Site Closure for three 91b Radioactive Wastes under a Performance Based Contract at Lackland Air Force Base, San Antonio, Texas. The Defense Environmental Restoration Program (DERP) was established by Section 211 of the Superfund Amendments and Reauthorization Act of 1986 (SARA). A part of the DERP provides for the cleanup of hazardous substances associated with past Department of Defense (DoD) activities and is consistent with the provisions of the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA). It is the Air Force Installation Restoration Program (IRP) that has responsibility for the cleanup activities associated with CERCLA. Under contract to the Air Force Center for Environmental Excellence (AFCEE), the ECC Project Team, that included ECC, Cabrera Services, and Malcolm Pirnie, was responsible for the implementation of the actions at three sites. The three IRP (91b) sites included RW015, a 0.02 square kilometer (5.5 acre) site, RW017 a 0.003 square kilometer (0.9 acre) site, and RW033 an 0.356 square kilometer (88 acre) site. Adding to the complexities of the project were issues of archaeological areas of interest, jurisdictional wetlands, land open to hunting, issues of security as well as compliance to the myriad of air force base rules, regulations, and Air Force Instructions (AFI). The award of the project task order was July of 2005, the project plan phase started in July of 2005 followed by the remedy implementation that included characterization and remediation as required reached completion in June of 2006. The project closure including the development and approval final status survey reports, proposed plans, and decision documents that parallel the CERCLA process was initiated in June of 2006 and is expected to reach completion in August of 2007. This paper will focus on the issues of working to achieve radiological and chemical closure under a performance based contract vehicle and the challenges encountered while reaching this goal. (authors)

  5. Ferrostaal eSolar JV | Open Energy Information

    Open Energy Info (EERE)

    Ferrostaal eSolar JV Jump to: navigation, search Name: Ferrostaal & eSolar JV Place: Germany Sector: Solar Product: Germany-based solar thermal electricity generation joint...

  6. China Technology Solar Power Holdings Ltd | Open Energy Information

    Open Energy Info (EERE)

    Solar Power Holdings Ltd Jump to: navigation, search Name: China Technology Solar Power Holdings Ltd Place: Hong Kong Sector: Solar Product: China-based solar project developer,...

  7. Esar Solar Power Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    Esar Solar Power Pvt Ltd Jump to: navigation, search Name: Esar Solar Power Pvt Ltd Place: Jaipur, Rajasthan, India Sector: Solar Product: Jaipur-based solar project developer....

  8. Hainan Tianwen Solar Power Co Ltd | Open Energy Information

    Open Energy Info (EERE)

    Solar Power Co Ltd Place: Hainan Province, China Sector: Solar Product: China-based solar thermal project developer References: Hainan Tianwen Solar Power Co Ltd1 This...

  9. Aggregated TiO2 Based Nanotubes for Dye Sensitized Solar Cells

    SciTech Connect (OSTI)

    Nie, Zimin; Zhou, Xiaoyuan; Zhang, Qifeng; Cao, Guozhong; Liu, Jun

    2013-11-01

    One-dimensional (1D) semiconducting oxides have attracted great attention for dye sensitized solar cells (DSCs), but the overall performance is still quite limited as compared to TiO2 nanocrystalline DSCs. Here, we report the synthesis of aggregated TiO2 based nanotubes with controlled morphologies and crystalline structures to obtain an overall power conversion efficiency of 9.9% using conventional dye without any additional chemical treatment steps. The high efficiency is attributed to the unique aggregate structure for light harvesting, optimized high surface area, and good crystallinity of the nanotube aggregates obtained through proper thermal annealing. This study demonstrates that high efficiency DSCs can be obtained with 1D nanomaterials, and provides lessons on the importance of optimizing both the nanocrystalline structure and the overall microscale morphology.

  10. CHARACTERIZING COMPLEXITY IN SOLAR MAGNETOGRAM DATA USING A WAVELET-BASED SEGMENTATION METHOD

    SciTech Connect (OSTI)

    Kestener, P.; Khalil, A.; Arneodo, A.

    2010-07-10

    The multifractal nature of solar photospheric magnetic structures is studied using the two-dimensional wavelet transform modulus maxima (WTMM) method. This relies on computing partition functions from the wavelet transform skeleton defined by the WTMM method. This skeleton provides an adaptive space-scale partition of the fractal distribution under study, from which one can extract the multifractal singularity spectrum. We describe the implementation of a multiscale image processing segmentation procedure based on the partitioning of the WT skeleton, which allows the disentangling of the information concerning the multifractal properties of active regions from the surrounding quiet-Sun field. The quiet Sun exhibits an average Hoelder exponent {approx}-0.75, with observed multifractal properties due to the supergranular structure. On the other hand, active region multifractal spectra exhibit an average Hoelder exponent {approx}0.38, similar to those found when studying experimental data from turbulent flows.

  11. Parameters influencing the deposition of methylammonium lead halide iodide in hole conductor free perovskite-based solar cells

    SciTech Connect (OSTI)

    Cohen, Bat-El; Gamliel, Shany; Etgar, Lioz

    2014-08-01

    Perovskite is a promising light harvester for use in photovoltaic solar cells. In recent years, the power conversion efficiency of perovskite solar cells has been dramatically increased, making them a competitive source of renewable energy. An important parameter when designing high efficiency perovskite-based solar cells is the perovskite deposition, which must be performed to create complete coverage and optimal film thickness. This paper describes an in-depth study on two-step deposition, separating the perovskite deposition into two precursors. The effects of spin velocity, annealing temperature, dipping time, and methylammonium iodide concentration on the photovoltaic performance are studied. Observations include that current density is affected by changing the spin velocity, while the fill factor changes mainly due to the dipping time and methylammonium iodide concentration. Interestingly, the open circuit voltage is almost unaffected by these parameters. Hole conductor free perovskite solar cells are used in this work, in order to minimize other possible effects. This study provides better understanding and control over the perovskite deposition through highly efficient, low-cost perovskite-based solar cells.

  12. SolarPower Ltd | Open Energy Information

    Open Energy Info (EERE)

    Ltd Jump to: navigation, search Name: SolarPower Ltd Place: Netanya, Israel Sector: Solar Product: Israel-based designer, supplier and installer of solar energy systems....

  13. Bay Solar Power Design | Open Energy Information

    Open Energy Info (EERE)

    Solar Power Design Jump to: navigation, search Name: Bay Solar Power Design Place: California Product: US-based PV system installer. References: Bay Solar Power Design1 This...

  14. Solar America LLC | Open Energy Information

    Open Energy Info (EERE)

    LLC Jump to: navigation, search Name: Solar America LLC Place: Marmora, New Jersey Zip: 8223 Sector: Solar Product: New Jersey-based company that designs and installs Solar...

  15. Suryachakra MSM Solar India | Open Energy Information

    Open Energy Info (EERE)

    MSM Solar India Jump to: navigation, search Name: Suryachakra MSM Solar India Place: Hyderabad, Andhra Pradesh, India Zip: 500 033 Sector: Solar Product: Hyderabad-based JV with...

  16. Solar Power Partners Inc | Open Energy Information

    Open Energy Info (EERE)

    Mill Valley, California Zip: 94941 Sector: Solar Product: Mill Valley-based independent power producer (IPP) focused on solar projects in the US References: Solar Power Partners...

  17. Solstice Solar Systems LLC | Open Energy Information

    Open Energy Info (EERE)

    California Zip: 95008-6906 Sector: Solar Product: US-based manufacturer of PV inverters and wires to connect solar panels. References: Solstice Solar Systems LLC1 This...

  18. Archimede Solar Energy Srl | Open Energy Information

    Open Energy Info (EERE)

    Archimede Solar Energy Srl Jump to: navigation, search Name: Archimede Solar Energy Srl Place: Massa Martana, Italy Zip: 6056 Sector: Solar Product: Italy-based producer of...

  19. Access Solar Energy LLC | Open Energy Information

    Open Energy Info (EERE)

    Solar Energy LLC Jump to: navigation, search Name: Access Solar Energy LLC Place: Park CIty, Utah Zip: 84060 Sector: Renewable Energy, Solar Product: Utah-based developers of...

  20. Carolina Solar Energy CSE | Open Energy Information

    Open Energy Info (EERE)

    CSE Jump to: navigation, search Name: Carolina Solar Energy (CSE) Place: Durham, North Carolina Zip: 27701 Sector: Solar Product: Durham-based developer of solar energy projects....

  1. Danish Solar Energy PLC | Open Energy Information

    Open Energy Info (EERE)

    Danish Solar Energy PLC Jump to: navigation, search Name: Danish Solar Energy PLC Place: Copenhagen - Freeport, Denmark Zip: DK-2100 Sector: Solar Product: Copenhagen-based...

  2. Rand Solar Energy Systems | Open Energy Information

    Open Energy Info (EERE)

    Rand Solar Energy Systems Jump to: navigation, search Name: Rand Solar Energy Systems Place: Petach Tikva, Israel Zip: 49130 Sector: Solar Product: Israel-based manufacturer and...

  3. Solar Depot Inc | Open Energy Information

    Open Energy Info (EERE)

    Place: Petaluma, California Zip: 94954 Sector: Solar Product: US-based PV and solar passive system integrator and distributor. References: Solar Depot Inc1 This article is a...

  4. Blue Planet Solar | Open Energy Information

    Open Energy Info (EERE)

    Planet Solar Jump to: navigation, search Name: Blue Planet Solar Place: Antwerp, Belgium Zip: B-2060 Sector: Services, Solar Product: Belgium-based firm that offers installation,...

  5. Team Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    Solar Inc Place: McClellan, California Zip: 95652 Sector: Solar Product: Team Solar Inc (TSI) is a contracting company based in Sacramento, California that specialises in...

  6. Solnechniy Potok Solar Stream | Open Energy Information

    Open Energy Info (EERE)

    Russian Federation Sector: Solar Product: Russia-based solar project developer and module manufacturer. References: Solnechniy Potok (Solar Stream)1 This article is a stub....

  7. Affirma Energia Solar | Open Energy Information

    Open Energy Info (EERE)

    Affirma Energia Solar Jump to: navigation, search Name: Affirma Energia Solar Place: Madrid, Spain Zip: 28046 Sector: Solar Product: Spain-based that is involved with the...

  8. Solar Millennium AG | Open Energy Information

    Open Energy Info (EERE)

    AG Jump to: navigation, search Name: Solar Millennium AG Place: Erlangen, Bavaria, Germany Zip: D-91052 Sector: Solar Product: Bavaria-based solar project developer; provides...

  9. Enterprise Solar Solutions | Open Energy Information

    Open Energy Info (EERE)

    Sector: Solar Product: New York-based company that specializes in commercial solar photovoltaic applications for businesses. References: Enterprise Solar Solutions1 This article...

  10. Atlantic Wind Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    search Name: Atlantic Wind & Solar Inc. Place: Coconut Groove, Florida Zip: 33133 Sector: Solar, Wind energy Product: Florida-based installer of distributed wind and solar systems...

  11. Standard Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    search Name: Standard Solar Inc Place: Gaithersburg, Maryland Zip: 20877 Sector: Solar Product: A Maryland-based installer of solar equipment for the residential and...

  12. Advanced Solar Technologies Inc | Open Energy Information

    Open Energy Info (EERE)

    California Sector: Solar Product: California-based domestic and commercial designer and installer of solar energy equipment. References: Advanced Solar Technologies Inc1 This...

  13. Teanaway Solar Reserve | Open Energy Information

    Open Energy Info (EERE)

    Sector: Solar Product: Washington State-based privately-held developer of the Teanaway Solar Reserve PV plant project. References: Teanaway Solar Reserve1 This article is a...

  14. Magnetic Force Microscopy Study of Zr2Co11 -Based Nanocrystalline Materials: Effect of Mo Addition

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Yue, Lanping; Jin, Yunlong; Zhang, Wenyong; Sellmyer, David J.

    2015-01-01

    Tmore » he addition of Molybdenum was used to modify the nanostructure and enhance coercivity of rare-earth-free Zr2Co11-based nanocrystalline permanent magnets. he effect of Mo addition on magnetic domain structures of melt spun nanocrystalline Zr16Co84-xMox(x=0, 0.5, 1, 1.5, and 2.0) ribbons has been investigated. It was found that magnetic properties and local domain structures are strongly influenced by Mo doping. he coercivity of the samples increases with the increase in Mo content (x≤1.5). he maximum energy product(BH)maxincreases with increasingxfrom 0.5 MGOe forx=0to a maximum value of 4.2 MGOe forx=1.5. he smallest domain size with a relatively short magnetic correlation length of 128 nm and largest root-mean-square phase shiftΦrmsvalue of 0.66° are observed for thex=1.5. he optimal Mo addition promotes magnetic domain structure refinement and thus leads to a significant increase in coercivity and energy product in this sample.« less

  15. NREL Develops ZnSiP2 for Silicon-Based Tandem Solar Cells (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2014-08-01

    Combining an Earth-abundant chalcopyrite with a silicon layer could significantly boost conversion efficiency above that of single-junction silicon solar cells.

  16. protective force

    National Nuclear Security Administration (NNSA)

    ntex%20-%20protective%20force%20-%20edited.jpg" alt"successfully completed a recent assessment by the U.S. Department " >

    Members of Pantex's Protective Force on...

  17. Thermal annealing study on P3HT: PCBM based bulk heterojunction organic solar cells using impedance spectroscopy

    SciTech Connect (OSTI)

    Gollu, Sankara Rao; Sharma, Ramakant G, Srinivas Gupta, Dipti

    2014-10-15

    Recently, Thermal annealing is an important process for bulk heterojunction organic solar cells (BHJ OSCs) to improve the device efficiency and performance of the organic solar cells. Here in, we have examined the changes in the efficiency and morphology of P3HT: PCBM film according to the thermal annealing temperature to find the changes during the annealing process by measuring the optical absorption, atomic force microscope and X-ray diffraction. We also investigated the effect of different annealing process conditions (without, pre- and post-annealing) on the device performance of the inverted bulk heterojunction organic solar cells consist the structure of ITO/ ZnO / P3HT: PCBM / MoO{sub 3}/ Al by measuring AC impedance characteristics. Particularly, the power conversion efficiency (PCE), crystalline nature of the polymer, light absorption and the surface smoothness of P3HT: PCBM films are significantly improved after the annealing process. These results indicated the improvement in terms of PCE, interface smoothness between the P3HT: PCBM and MoO{sub 3} layers of the post annealed device originated from the decrease of series resistance between P3HT: PCBM layer and Al electrodes, which could be due to decrease in the effective life time of charge carriers.

  18. Optimizing the fabrication process and interplay of device components of polymer solar cells using a field-based multiscale solar-cell algorithm

    SciTech Connect (OSTI)

    Donets, Sergii; Pershin, Anton; Baeurle, Stephan A.

    2015-05-14

    Both the device composition and fabrication process are well-known to crucially affect the power conversion efficiency of polymer solar cells. Major advances have recently been achieved through the development of novel device materials and inkjet printing technologies, which permit to improve their durability and performance considerably. In this work, we demonstrate the usefulness of a recently developed field-based multiscale solar-cell algorithm to investigate the influence of the material characteristics, like, e.g., electrode surfaces, polymer architectures, and impurities in the active layer, as well as post-production treatments, like, e.g., electric field alignment, on the photovoltaic performance of block-copolymer solar-cell devices. Our study reveals that a short exposition time of the polymer bulk heterojunction to the action of an external electric field can lead to a low photovoltaic performance due to an incomplete alignment process, leading to undulated or disrupted nanophases. With increasing exposition time, the nanophases align in direction to the electric field lines, resulting in an increase of the number of continuous percolation paths and, ultimately, in a reduction of the number of exciton and charge-carrier losses. Moreover, we conclude by modifying the interaction strengths between the electrode surfaces and active layer components that a too low or too high affinity of an electrode surface to one of the components can lead to defective contacts, causing a deterioration of the device performance. Finally, we infer from the study of block-copolymer nanoparticle systems that particle impurities can significantly affect the nanostructure of the polymer matrix and reduce the photovoltaic performance of the active layer. For a critical volume fraction and size of the nanoparticles, we observe a complete phase transformation of the polymer nanomorphology, leading to a drop of the internal quantum efficiency. For other particle-numbers and -sizes, we observe only a local perturbation of the nanostructure, diminishing the number of continuous percolation paths to the electrodes and, therefore, reducing the device performance. From these investigations, we conclude that our multiscale solar-cell algorithm is an effective approach to investigate the impact of device materials and post-production treatments on the photovoltaic performance of polymer solar cells.

  19. User`s manual for TMY2s: Derived from the 1961--1990 National Solar Radiation Data Base

    SciTech Connect (OSTI)

    Marion, W.; Urban, K.

    1995-06-01

    This report is a user`s manual that describes typical meteorological year (TMY) data sets derived from the 1961-1990 National Solar Radiation Data Base. The TMY is a data set of hourly values of solar radiation and meteorological elements for a 1-year period. The intended use if for computer simulations of solar energy conversion systems and building systems. Section 1 of the manual provides general information about the TMYs; Section 2 lists the stations and provides station identifying information and classification; Section 3 details the contents of the TMY2 files and provides the hourly records of data values; Section 4 compares TMY2 with 30-year data sets; Appendices provide procedures used to develop TMYs and a table to convert SI data to other units.

  20. Synchrotron-based analysis of chromium distributions in multicrystalline silicon for solar cells

    SciTech Connect (OSTI)

    Jensen, Mallory Ann; Hofstetter, Jasmin; Morishige, Ashley E.; Coletti, Gianluca; Lai, Barry; Fenning, David P.; Buonassisi, Tonio

    2015-05-18

    Chromium (Cr) can degrade silicon wafer-based solar cell efficiencies at concentrations as low as 10(10) cm(-3). In this contribution, we employ synchrotron-based X-ray fluorescence microscopy to study chromium distributions in multicrystalline silicon in as-grown material and after phosphorous diffusion. We complement quantified precipitate size and spatial distribution with interstitial Cr concentration and minority carrier lifetime measurements to provide insight into chromium gettering kinetics and offer suggestions for minimizing the device impacts of chromium. We observe that Cr-rich precipitates in as-grown material are generally smaller than iron-rich precipitates and that Cri point defects account for only one-half of the total Cr in the as-grown material. This observation is consistent with previous hypotheses that Cr transport and CrSi2 growth are more strongly diffusion-limited during ingot cooling. We apply two phosphorous diffusion gettering profiles that both increase minority carrier lifetime by two orders of magnitude and reduce [Cr-i] by three orders of magnitude to approximate to 10(10) cm(-3). Some Cr-rich precipitates persist after both processes, and locally high [Cri] after the high-temperature process indicates that further optimization of the chromium gettering profile is possible. (C) 2015 AIP Publishing LLC.

  1. Midtemperature Solar Systems Test Facility predictions for thermal performance based on test data. Alpha Solarco Model 104 solar collector with 0. 125-inch Schott low-iron glass reflector surface

    SciTech Connect (OSTI)

    Harrison, T.D.

    1981-04-01

    Thermal performance predictions based on test data are presented for the Alpha Solarco Model 104 solar collector, with 0.125-inch Schott low-iron glass reflector surface, for three output temperatures at five cities in the United States.

  2. Satellite-Based Solar Resource Data Sets for India 2002-2012

    SciTech Connect (OSTI)

    Sengupta, M.; Perez, R.; Gueymard, C.; Anderberg, M.; Gotseff, P.

    2014-02-01

    A new 10-km hourly solar resource product was created for India. This product was created using satellite radiances from the Meteosat series of satellites. The product contains global horizontal irradiances (GHI) and direct normal irradiances (DNI) for the period from 2002 to 2011. An additional solar resource data set covering the period from January 2012 to June 2012 was created solely for validation because this period overlaps ground measurements that were made available from the Indian Ministry of New and Renewable Energy's (MNRE's) National Institute for Solar Energy for five stations that are part of MNRE's solar resource network. These measurements were quality checked using the SERI QC software and used to validate the satellite product. A comparison of the satellite product to the ground measurements for the five stations shows good agreement. This report also presents a comparison of the new version of solar resource data to the previous version, which covered the period from 2002 to 2008.

  3. Direct Aerosol Forcing Uncertainty

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Mccomiskey, Allison

    2008-01-15

    Understanding sources of uncertainty in aerosol direct radiative forcing (DRF), the difference in a given radiative flux component with and without aerosol, is essential to quantifying changes in Earth's radiation budget. We examine the uncertainty in DRF due to measurement uncertainty in the quantities on which it depends: aerosol optical depth, single scattering albedo, asymmetry parameter, solar geometry, and surface albedo. Direct radiative forcing at the top of the atmosphere and at the surface as well as sensitivities, the changes in DRF in response to unit changes in individual aerosol or surface properties, are calculated at three locations representing distinct aerosol types and radiative environments. The uncertainty in DRF associated with a given property is computed as the product of the sensitivity and typical measurement uncertainty in the respective aerosol or surface property. Sensitivity and uncertainty values permit estimation of total uncertainty in calculated DRF and identification of properties that most limit accuracy in estimating forcing. Total uncertainties in modeled local diurnally averaged forcing range from 0.2 to 1.3 W m-2 (42 to 20%) depending on location (from tropical to polar sites), solar zenith angle, surface reflectance, aerosol type, and aerosol optical depth. The largest contributor to total uncertainty in DRF is usually single scattering albedo; however decreasing measurement uncertainties for any property would increase accuracy in DRF. Comparison of two radiative transfer models suggests the contribution of modeling error is small compared to the total uncertainty although comparable to uncertainty arising from some individual properties.

  4. GA Solar | Open Energy Information

    Open Energy Info (EERE)

    Spain Zip: 28045 Sector: Solar Product: Madrid based solar project developer, owned by Spanish industrial group Corporacion Gestamp. Coordinates: 40.4203, -3.705774 Show Map...

  5. Auxin Solar | Open Energy Information

    Open Energy Info (EERE)

    Auxin Solar Jump to: navigation, search Name: Auxin Solar Place: Campbell, California Product: Silicon Valley-based Auxin manufactures crystalline PV modules ranging from 10W to...

  6. Aray Solar | Open Energy Information

    Open Energy Info (EERE)

    Aray Solar Jump to: navigation, search Name: Aray Solar Place: Praha 1, Czech Republic Zip: 11000 Product: PV project developer with activities across Europe based in the Czech...

  7. Stardate Solar | Open Energy Information

    Open Energy Info (EERE)

    Stardate Solar Jump to: navigation, search Name: Stardate Solar Place: Santa Cruz, California Zip: 95060 Product: Installer and distributor of Suntech modules, based in Santa Cruz,...

  8. Solare AG | Open Energy Information

    Open Energy Info (EERE)

    AG Jump to: navigation, search Name: Solare AG Place: Cologne, North Rhine-Westphalia, Germany Zip: 50678 Sector: Solar Product: Germany-based equipment manufacturer and developer...

  9. ICE Solar | Open Energy Information

    Open Energy Info (EERE)

    India Sector: Solar Product: India-based company focused on solar PV engineering, procurement and construction opportunities. Coordinates: 17.6726, 77.5971 Show Map Loading...

  10. Magnolia Solar | Open Energy Information

    Open Energy Info (EERE)

    Magnolia Solar Jump to: navigation, search Name: Magnolia Solar Place: Woburn, Massachusetts Zip: 1801 Product: Massachusetts-based thin-film PV startup. Coordinates: 42.479195,...

  11. BP Solar | Open Energy Information

    Open Energy Info (EERE)

    Maryland Zip: 21703 Sector: Solar Product: Maryland-based subsidiary of BP Alternative Energy dealing with solar power. Website: www.bp.comgenericcountryjump. Coordinates:...

  12. Dalkia Solar | Open Energy Information

    Open Energy Info (EERE)

    Agullent, Spain Zip: 46890 Sector: Solar Product: Agullent-based installer of photovoltaic and solar thermal power plants. Coordinates: 38.824755, -0.547039 Show Map...

  13. Solar Distinction | Open Energy Information

    Open Energy Info (EERE)

    Distinction Jump to: navigation, search Name: Solar Distinction Place: Albuquerque, New Mexico Product: New Mexico-based PV module maker. References: Solar Distinction1 This...

  14. Evolution Solar | Open Energy Information

    Open Energy Info (EERE)

    Product: British Virgin Islands-based solar energy company dedicated to establishing solar panel factories in the Middle East and Africa using both Crystalline Silicon and...

  15. CCT Solar | Open Energy Information

    Open Energy Info (EERE)

    CCT Solar Jump to: navigation, search Name: CCT Solar Place: Ede, Netherlands Zip: 6711 Product: Netherlands-based division of CCT Europe and PV panel and junction box...

  16. Radiance Solar | Open Energy Information

    Open Energy Info (EERE)

    Radiance Solar Jump to: navigation, search Name: Radiance Solar Place: Atlanta, Georgia Zip: 30318 Product: Commercial and residential PV installer based in Atlanta. Coordinates:...

  17. Thermal influence on charge carrier transport in solar cells based on GaAs PN junctions

    SciTech Connect (OSTI)

    Osses-Márquez, Juan; Calderón-Muñoz, Williams R.

    2014-10-21

    The electron and hole one-dimensional transport in a solar cell based on a Gallium Arsenide (GaAs) PN junction and its dependency with electron and lattice temperatures are studied here. Electrons and heat transport are treated on an equal footing, and a cell operating at high temperatures using concentrators is considered. The equations of a two-temperature hydrodynamic model are written in terms of asymptotic expansions for the dependent variables with the electron Reynolds number as a perturbation parameter. The dependency of the electron and hole densities through the junction with the temperature is analyzed solving the steady-state model at low Reynolds numbers. Lattice temperature distribution throughout the device is obtained considering the change of kinetic energy of electrons due to interactions with the lattice and heat absorbed from sunlight. In terms of performance, higher values of power output are obtained with low lattice temperature and hot energy carriers. This modeling contributes to improve the design of heat exchange devices and thermal management strategies in photovoltaic technologies.

  18. Multi-crystalline II-VI based multijunction solar cells and modules

    SciTech Connect (OSTI)

    Hardin, Brian E.; Connor, Stephen T.; Groves, James R.; Peters, Craig H.

    2015-06-30

    Multi-crystalline group II-VI solar cells and methods for fabrication of same are disclosed herein. A multi-crystalline group II-VI solar cell includes a first photovoltaic sub-cell comprising silicon, a tunnel junction, and a multi-crystalline second photovoltaic sub-cell. A plurality of the multi-crystalline group II-VI solar cells can be interconnected to form low cost, high throughput flat panel, low light concentration, and/or medium light concentration photovoltaic modules or devices.

  19. Shunda SolarE Technologies | Open Energy Information

    Open Energy Info (EERE)

    Sector: Solar Product: US-based JV with vertically integrated operations in the solar market. References: Shunda-SolarE Technologies1 This article is a stub. You can...

  20. Solar Technology Acceleration Centre SolarTAC | Open Energy Informatio...

    Open Energy Info (EERE)

    Acceleration Centre SolarTAC Jump to: navigation, search Name: Solar Technology Acceleration Centre (SolarTAC) Product: US-based JV formed with a consortium of six public and...

  1. Solar collection

    SciTech Connect (OSTI)

    Cole, S.L.

    1984-08-01

    This report contains summaries and pictures of projects funded by the Appropriate Technology Small Grants Program which include the following solar technologies: solar dish; photovoltaics; passive solar building and solar hot water system; Trombe wall; hot air panel; hybrid solar heating system; solar grain dryer; solar greenhouse; solar hot water workshops; and solar workshops.

  2. air force

    National Nuclear Security Administration (NNSA)

    en NNSA, Air Force Complete Successful B61-12 Life Extension Program Development Flight Test at Tonopah Test Range http:nnsa.energy.govmediaroompressreleases...

  3. High Efficiency CdTe Ink-Based Solar Cells Using Nanocrystals (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2015-01-01

    This NREL Highlight is being developed for the 2015 February Alliance S&T Board meeting and describes a solution-processable ink to produce high-efficiency solar cells using low temperature and simple processing.

  4. Project Profile: Regenerative Carbonate-Based Thermochemical Energy Storage System for Concentrating Solar Power

    Broader source: Energy.gov [DOE]

    The Department of Energy’s SunShot Initiative awarded Southern Research Institute (SRI) through the Concentrating Solar Power: Efficiently Leveraging Equilibrium Mechanisms for Engineering New Thermochemical Storage (CSP: ELEMENTS) funding program.

  5. Quantum Solar | Open Energy Information

    Open Energy Info (EERE)

    Solar Jump to: navigation, search Name: Quantum Solar Place: Santa Fe, New Mexico Zip: 87507 Product: New Mexico-based PV cell technology company. References: Quantum Solar1 This...

  6. Superfund record of decision (EPA region 10): Eielson Air Force Base, Fairbanks-North Star Borough, AK, September 30, 1996

    SciTech Connect (OSTI)

    1997-10-01

    The decision document presents the final remedial action selected for Eielson Air Force Base (AFB), Alaska. The sitewide investigation at Eielson AFB evaluated basewide contamination that is not confined or attributable to specific source areas identified and addressed in the FFA as well as cumulative risks to human health and the environment posed by contamination on a sitewide basis. Garrison Slough is the only one that poses an unacceptable risk to human health and the environment. Polychlorinated biphenyls (PCBs) were found in the fish tissue and sediments of Garrison Slough. Soils in a trench adjacent to Garrison Slough were contaminated with PCBs and appear to be the source of contamination to slough sediments via surface water runoff. The major components of the selected remedy include: Fishing restrictions in Garrison Slough; Fish control device near the downstream edge of Eielson AFB; Excavation of contaminated soils and sediments with concentrations greater than 10 mg/kg PCBs; Onsite disposal of material with PCB concentrations less than 50 mg/kg; Offsite disposal or treatment of materials with PCB concentrations greater than 50 mg/kg in accordance with the Toxic Substances Control Act (TSCA), 40 CFR part 761; and Environmental monitoring of soils, sediments, surface water, fish, and groundwater.

  7. Selection of higher eigenmode amplitude based on dissipated power and virial contrast in bimodal atomic force microscopy

    SciTech Connect (OSTI)

    Diaz, Alfredo J.; Eslami, Babak; Lpez-Guerra, Enrique A.; Solares, Santiago D.

    2014-09-14

    This paper explores the effect of the amplitude ratio of the higher to the fundamental eigenmode in bimodal atomic force microscopy (AFM) on the phase contrast and the dissipated power contrast of the higher eigenmode. We explore the optimization of the amplitude ratio in order to maximize the type of contrast that is most relevant to the particular study. Specifically, we show that the trends in the contrast range behave differently for different quantities, especially the dissipated power and the phase, with the former being more meaningful than the latter (a similar analysis can be carried out using the virial, for which we also provide a brief example). Our work is based on numerical simulations using two different conservative-dissipative tip-sample models, including the standard linear solid and the combination of a dissipation coefficient with a conservative model, as well as experimental images of thin film Nafion{sup } proton exchange polymers. We focus on the original bimodal AFM method, where the higher eigenmode is driven with constant amplitude and frequency (i.e., in open loop).

  8. Development of Novel Nanocrystal-based Solar Cell to Exploit Multiple Exciton Generation: Cooperative Research and Development Final Report, CRADA Number CRD-07-00227

    SciTech Connect (OSTI)

    Ellingson, R.

    2010-08-01

    The purpose of the project was to develop new design and fabrication techniques for NC solar cells with the goal of demonstrating enhanced photocurrent and efficiency by exploiting multiple exciton generation and to investigate multiple exciton generation and charge carrier dynamics in semiconductor NC films used in NC-based solar cells.

  9. Experimental studies on heat transfer and friction factor characteristics of forced circulation solar water heater system fitted with helical twisted tapes

    SciTech Connect (OSTI)

    Jaisankar, S.; Radhakrishnan, T.K.; Sheeba, K.N.

    2009-11-15

    Experimental investigation of heat transfer, friction factor and thermal performance of twisted tape solar water heater with various twist ratios has been conducted and the results are compared with plain tube collector for the same operating conditions with Reynolds number varied from 3000 to 23,000. Experimental data from plain tube collector is validated with the fundamental equations and found that the discrepancy is less than {+-}5.35% and {+-}8.80% for Nusselt number and friction factor, respectively. Correlations have been developed for Nusselt number and friction factor with various twist ratios (Y = 3, 4, 5, 6) and are compared with the experimental values. Results conclude that, heat transfer and pressure drop are higher in twisted tape collector compared to the plain one. Among the various twist ratios, the minimum twist ratio 3 is found to enhance the heat transfer and pressure drop due to swirl generation. As the twist ratio increases, the swirl generation decreases and minimizes the heat transfer and friction factor. (author)

  10. Community Shared Solar with Solarize | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Community Shared Solar with Solarize Community Shared Solar with Solarize

  11. IM2 Energia Solar | Open Energy Information

    Open Energy Info (EERE)

    IM2 Energia Solar Jump to: navigation, search Name: IM2 Energia Solar Place: Valencia, Spain Zip: 46002 Sector: Solar Product: Valencia-based developer of roof-mounted solar...

  12. SunTrac Solar | Open Energy Information

    Open Energy Info (EERE)

    SunTrac Solar Place: Golden,, Colorado Zip: 80403 Sector: Solar Product: Colorado based solar thermal integrator References: SunTrac Solar1 This article is a stub. You can help...

  13. SolarWorld Korea | Open Energy Information

    Open Energy Info (EERE)

    Korea-based JV set up by SolarWorld AG and SolarPark Engineering Co Ltd aimed at manufacturing solar modules and installing utility-scale PV projects. References: SolarWorld...

  14. Roof-top solar energy potential under performance-based building energy codes: The case of Spain

    SciTech Connect (OSTI)

    Izquierdo, Salvador; Montanes, Carlos; Dopazo, Cesar; Fueyo, Norberto

    2011-01-15

    The quantification at regional level of the amount of energy (for thermal uses and for electricity) that can be generated by using solar systems in buildings is hindered by the availability of data for roof area estimation. In this note, we build on an existing geo-referenced method for determining available roof area for solar facilities in Spain to produce a quantitative picture of the likely limits of roof-top solar energy. The installation of solar hot water systems (SHWS) and photovoltaic systems (PV) is considered. After satisfying up to 70% (if possible) of the service hot water demand in every municipality, PV systems are installed in the remaining roof area. Results show that, applying this performance-based criterion, SHWS would contribute up to 1662 ktoe/y of primary energy (or 68.5% of the total thermal-energy demand for service hot water), while PV systems would provide 10 T W h/y of electricity (or 4.0% of the total electricity demand). (author)

  15. Force sensor

    DOE Patents [OSTI]

    Grahn, A.R.

    1993-05-11

    A force sensor and related method for determining force components is described. The force sensor includes a deformable medium having a contact surface against which a force can be applied, a signal generator for generating signals that travel through the deformable medium to the contact surface, a signal receptor for receiving the signal reflected from the contact surface, a generation controller, a reception controller, and a force determination apparatus. The signal generator has one or more signal generation regions for generating the signals. The generation controller selects and activates the signal generation regions. The signal receptor has one or more signal reception regions for receiving signals and for generating detections signals in response thereto. The reception controller selects signal reception regions and detects the detection signals. The force determination apparatus measures signal transit time by timing activation and detection and, optionally, determines force components for selected cross-field intersections. The timer which times by activation and detection can be any means for measuring signal transit time. A cross-field intersection is defined by the overlap of a signal generation region and a signal reception region.

  16. Force sensor

    DOE Patents [OSTI]

    Grahn, Allen R.

    1993-01-01

    A force sensor and related method for determining force components. The force sensor includes a deformable medium having a contact surface against which a force can be applied, a signal generator for generating signals that travel through the deformable medium to the contact surface, a signal receptor for receiving the signal reflected from the contact surface, a generation controller, a reception controller, and a force determination apparatus. The signal generator has one or more signal generation regions for generating the signals. The generation controller selects and activates the signal generation regions. The signal receptor has one or more signal reception regions for receiving signals and for generating detections signals in response thereto. The reception controller selects signal reception regions and detects the detection signals. The force determination apparatus measures signal transit time by timing activation and detection and, optionally, determines force components for selected cross-field intersections. The timer which times by activation and detection can be any means for measuring signal transit time. A cross-field intersection is defined by the overlap of a signal generation region and a signal reception region.

  17. Economic analysis of operating alternatives for the South Vandenberg Power Plant at Vandenberg Air Force Base, California

    SciTech Connect (OSTI)

    Daellenbach, K.K.; Dagle, J.E.; Reilly, R.W.; Shankle, S.A.

    1993-02-01

    Vandenberg Air Force Base (VAFB), located approximately 50 miles northwest of Santa Barbara, California, commissioned the Pacific Northwest Laboratory to conduct an economic analysis of operating alternatives of the South Vandenberg Power Plant (SVPP). Recent concern over SVPP operating and environmental costs prompted VAFB personnel to consider other means to support the Missile Operation Support Requirement (MOSR). The natural gas-fired SVPP was originally designed to support the Space Transportation System launch activities. With cancellation of this mission, the SVPP has been used to provide primary and backup electric power to support MOSR activities for the Space Launch Complexes. This document provides economic analysis in support of VAFB decisions about future operation of the SVPP. This analysis complied with the life-cycle cost (LCC) analytical approach detailed in 10 CFR 436, which is used in support of all Federal energy decisions. Many of the SVPP operational and environmental cost estimates were provided by VAFB staff, with additional information from vendors and engineering contractors. The LCC analysis consisted of three primary operating strategies, each with a level of service equal to or better than the current status-quo operation. These scenarios are: Status-quo operation where the SVPP provides both primary and backup MOSR power; Purchased utility power providing primary MOSR support with backup power provided by an Uninterruptible Power Supply (UPS) system. The SVPP would be used to provide power for long-duration power outages; Purchased utility power provides primary MOSR support with backup power provided by a UPS system. A new set of dedicated generators would provide backup power for long-duration power outages.

  18. Efficient inverted polymer solar cells based on conjugated polyelectrolyte and zinc oxide modified ITO electrode

    SciTech Connect (OSTI)

    Yuan, Tao; Zhu, Xiaoguang; Tu, Guoli; Zhou, Lingyu; Zhang, Jian

    2015-02-23

    Efficient inverted polymer solar cells (PSCs) were constructed by utilizing a conjugated polyelectrolyte PF{sub EO}SO{sub 3}Na and zinc oxide to modify the indium tin oxide (ITO) electrode. The ITO electrode modified by PF{sub EO}SO{sub 3}Na and zinc oxide possesses high transparency, increased electron mobility, smoothened surface, and lower work function. PTB7:PC{sub 71}BM inverted PSCs containing the modified ITO electrode achieved a high power conversion efficiency (PCE) of 8.49%, exceeding that of the control device containing a ZnO modified ITO electrode (7.48%). Especially, PCE-10:PC{sub 71}BM inverted polymer solar cells achieved a high PCE up to 9.4%. These results demonstrate a useful approach to improve the performance of inverted polymer solar cells.

  19. Improve photovoltaic performance of titanium dioxide nanorods based dye-sensitized solar cells by Ca-doping

    SciTech Connect (OSTI)

    Li, Weixin; Yang, Junyou Zhang, Jiaqi; Gao, Sheng; Luo, Yubo; Liu, Ming

    2014-09-15

    Highlights: • TiO{sub 2} nanorods doped with Ca ions were synthesized by one-step hydrothermal method. • The flat band edge of rutile TiO{sub 2} shifted positively via Ca-doping. • The photoelectric conversion efficiency of dye-sensitized solar cells (DSSCs) based on TiO{sub 2} electrode was much enhanced by Ca-doping. • A relatively high open circuit voltage was obtained by adopting Ca-doped TiO{sub 2} nanorods electrode. - Abstract: Ca-doped TiO{sub 2} nanorod arrays were prepared via the one-step hydrothermal method successfully, and the effect of Ca ions content on the photovoltaic conversion efficiency of dye-sensitized solar cells has been fully discussed in the paper. Although no obvious change on the microstructure and morphology was observed by field emission scanning electron microscope and transmission electron microscope for the Ca-doped samples, the results of X-ray diffraction and X-ray photoelectron spectroscopy confirmed that Ti{sup 4+} was substituted with Ca{sup 2+} successfully. UV–vis spectroscopy results revealed that the flat band edge shifted positively by Ca ions doping. The photovoltaic conversion efficiency of the dye-sensitized solar cells based on the 2 mol% Ca-doped TiO{sub 2} electrode was 43% higher than that of the undoped one due to the less recombination possibility.

  20. Protective Force

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2005-08-26

    Establishes requirements for management and operation of the DOE Protective Force (PF), establishes requirements for firearms operations and defines the firearms courses of fire. Cancels: DOE M 473.2-1A DOE M 473.2-2

  1. Thin Metal Oxide Films to Modify a Window Layer in CdTe-Based Solar Cells for Improved Performance

    SciTech Connect (OSTI)

    Lemmon, John P.; Polikarpov, Evgueni; Bennett, Wendy D.; Kovarik, Libor

    2012-05-25

    We report on CdS/CdTe photovoltaic devices that contain a thin Ta₂O₅ film deposited onto the CdS window layer by sputtering. We show that for thicknesses below 5 nm, Ta₂O₅ films between CdS and CdTe positively affect the solar cell performance, improving JSC, VOC, and the cell power conversion efficiency despite the insulating nature of the interlayer material. Using the Ta₂O₅ interlayer, a VOC gain of over 100 mV was demonstrated compared to a CdTe/CdS baseline. Application of a 1nm Ta₂O₅ interlayer enabled the fabrication of CdTe solar cells with extremely thin (less than 30 nm) CdS window layers. The efficiency of these cells exceeded that of a base line cell with 95 nm of CdS.

  2. Protective Force

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2006-03-07

    The manual establishes requirements for management and operation of the DOE Protective Force, establishes requirements for firearms operations and defines the firearms courses of fire. Chg 1 dated 3/7/06. DOE M 470.4-3A cancels DOE M 470.4-3, Chg 1, Protective Force, dated 3-7-06, Attachment 2, Contractor Requirement Document (CRD) only (except for Section C). Chg 1, dated 3-7-06, cancels DOE M 470.4-3

  3. Analysis of the efficiency of intermediate band solar cells based on quantum dot supercrystals

    SciTech Connect (OSTI)

    Heshmati, S; Golmohammadi, S; Abedi, K; Taleb, H

    2014-03-28

    We have studied the influence of the quantum-dot (QD) width and the quantum-dot conduction band (QD-CB) offset on the efficiency of quantum-dot intermediate band solar cells (QD-IBSCs). Simulation results demonstrate that with increasing QD-CB offset and decreasing QD width, the maximum efficiency is achieved. (laser applications and other topics in quantum electronics)

  4. Theoretical performance of solar cell based on mini-bands quantum dots

    SciTech Connect (OSTI)

    Aly, Abou El-Maaty M. E-mail: ashraf.nasr@gmail.com; Nasr, A. E-mail: ashraf.nasr@gmail.com

    2014-03-21

    The tremendous amount of research in solar energy is directed toward intermediate band solar cell for its advantages compared with the conventional solar cell. The latter has lower efficiency because the photons have lower energy than the bandgap energy and cannot excite mobile carriers from the valence band to the conduction band. On the other hand, if mini intermediate band is introduced between the valence and conduction bands, then the smaller energy photons can be used to promote charge carriers transfer to the conduction band and thereby the total current increases while maintaining a large open circuit voltage. In this article, the influence of the new band on the power conversion efficiency for structure of quantum dots intermediate band solar cell is theoretically investigated and studied. The time-independent Schrdinger equation is used to determine the optimum width and location of the intermediate band. Accordingly, achievement of a maximum efficiency by changing the width of quantum dots and barrier distances is studied. Theoretical determination of the power conversion efficiency under the two different ranges of QD width is presented. From the obtained results, the maximum power conversion efficiency is about 70.42%. It is carried out for simple cubic quantum dot crystal under fully concentrated light. It is strongly dependent on the width of quantum dots and barrier distances.

  5. Solar energy concentrator design and operation. (Latest citations from the NTIS data base). Published Search

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    The bibliography contains citations concerning the design and operation of solar energy concentrators. Topics include system descriptions, performance evaluations, technology reviews and development studies, cost considerations, and materials aspects. Optical properties of various systems, performance simulations, fabrication techniques, and control systems are discussed. Photovoltaic and thermal systems are also considered. (Contains 250 citations and includes a subject term index and title list.)

  6. Control of focusing forces and emittances in plasma-based accelerators using near-hollow plasma channels

    SciTech Connect (OSTI)

    Schroeder, C. B.; Esarey, E.; Benedetti, C.; Leemans, W. P.

    2013-08-15

    A near-hollow plasma channel, where the plasma density in the channel is much less than the plasma density in the walls, is proposed to provide independent control over the focusing and accelerating forces in a plasma accelerator. In this geometry the low density in the channel contributes to the focusing forces, while the accelerating fields are determined by the high density in the channel walls. The channel also provides guiding for intense laser pulses used for wakefield excitation. Both electron and positron beams can be accelerated in a nearly symmetric fashion. Near-hollow plasma channels can effectively mitigate emittance growth due to Coulomb scattering for high-energy physics applications.

  7. Midtemperature solar systems test facility predictions for thermal performance based on test data: AAI solar collector with pressure-formed glass reflector surface

    SciTech Connect (OSTI)

    Harrison, T.D.

    1981-03-01

    Sandia National Laboratories, Albuquerque (SNLA), is currently conducting a program to predict the performance and measure the characteristics of commercially available solar collectors that have the potential for use in industrial process heat and enhance oil recovery applications. The thermal performance predictions for the AAI solar line-focusing slat-type collector for five cities in the US are presented. (WHK)

  8. Chesapeake Solar LLC a groSolar company | Open Energy Information

    Open Energy Info (EERE)

    Maryland Zip: 20794 Sector: Solar Product: Maryland-based company that installs solar electricity and solar hot water systems, which was acquired by groSolar in July 2008....

  9. Conservation and solar guidelines

    SciTech Connect (OSTI)

    Balcomb, J.D.

    1983-01-01

    Guidelines are given for selecting R-values and infiltration levels, and determining the size of the solar collection area for passive solar buildings. The guidelines are based on balancing the incremental cost/benefit of conservation and passive solar strategies. Tables are given for 90 cities in the US and the results are also displayed on maps. An example is included.

  10. Photovoltaic properties and morphology of organic solar cells based on liquid-crystal semiconducting polymer with additive

    SciTech Connect (OSTI)

    Suzuki, Atsushi; Zushi, Masahito; Suzuki, Hisato; Ogahara, Shinichi; Akiyama, Tsuyoshi; Oku, Takeo

    2014-02-20

    Bulk heterojunction organic solar cell based on liquid crystal semiconducting polymers of poly[9,9-dioctylfluorene-co-bithiophene] (F8T2) as p-type semiconductors and fullerenes (C{sub 60}) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) as electron donor and acceptor has been fabricated and characterized for improving photovoltaic and optical properties. The photovoltaic performance including current voltage curves in the dark and illumination of the F8T2/C{sub 60} conventional and inverted bulk heterojunction solar cells were investigated. Relationship between the photovoltaic properties and morphological behavior was focused on tuning for optimization of photo-voltaic performance under annealing condition near glass transition temperature. Additive-effect of diiodooctane (DIO) and poly(3-hexylthiophene-2,5-diyl) (P3HT) on the photovoltaic performance and optical properties was investigated. Mechanism of the photovoltaic properties of the conventional and inverted solar cells will be discussed by the experimental results.

  11. Research on high-efficiency, multiple-gap, multijunction, amorphous-silicon-based alloy thin-film solar cells

    SciTech Connect (OSTI)

    Guha, S. )

    1989-06-01

    This report presents results of research on advancing our understanding of amorphous-silicon-based alloys and their use in small-area multijunction solar cells. The principal objectives of the program are to develop a broad scientific base for the chemical, structural, optical, and electronic properties of amorphous-silicon-based alloys; to determine the optimum properties of these alloy materials as they relate to high-efficiency cells; to determine the optimum device configuration for multijunction cells; and to demonstrate proof-of-concept, multijunction, a-Si-alloy-based solar cells with 18% efficiency under standard AM1.5 global insolation conditions and with an area of at least 1 cm{sup 2}. A major focus of the work done during this reporting period was the optimization of a novel, multiple-graded structure that enhances cell efficiency through band-gap profiling. The principles of the operation of devices incorporating such a structure, computer simulations of those, and experimental results for both single- and multijunction cells prepared by using the novel structure are discussed in detail. 14 refs., 35 figs., 7 tabs.

  12. Metal complex-based electron-transfer mediators in dye-sensitized solar cells

    DOE Patents [OSTI]

    Elliott, C. Michael; Sapp, Shawn A.; Bignozzi, Carlo Alberto; Contado, Cristiano; Caramori, Stefano

    2006-03-28

    This present invention provides a metal-ligand complex and methods for using and preparing the same. In particular, the metal-ligand complex of the present invention is of the formula: L.sub.a-M-X.sub.b where L, M, X, a, and b are those define herein. The metal-ligand complexes of the present invention are useful in a variety of applications including as electron-transfer mediators in dye-sensitized solar cells and related photoelectrochromic devices.

  13. Physics-Based GOES Satellite Product for Use in NREL's National Solar Radiation Database: Preprint

    SciTech Connect (OSTI)

    Sengupta, M.; Habte, A.; Gotseff, P.; Weekley, A.; Lopez, A.; Molling, C.; Heidinger, A.

    2014-07-01

    The National Renewable Energy Laboratory (NREL), University of Wisconsin, and National Oceanic Atmospheric Administration are collaborating to investigate the integration of the Satellite Algorithm for Shortwave Radiation Budget (SASRAB) products into future versions of NREL's 4-km by 4-km gridded National Solar Radiation Database (NSRDB). This paper describes a method to select an improved clear-sky model that could replace the current SASRAB global horizontal irradiance and direct normal irradiances reported during clear-sky conditions.

  14. ZnS/Zn(O,OH)S-based buffer layer deposition for solar cells

    DOE Patents [OSTI]

    Bhattacharya, Raghu N.

    2009-11-03

    The invention provides CBD ZnS/Zn(O,OH)S and spray deposited ZnS/Zn(O,OH)S buffer layers prepared from a solution of zinc salt, thiourea and ammonium hydroxide dissolved in a non-aqueous/aqueous solvent mixture or in 100% non-aqueous solvent. Non-aqueous solvents useful in the invention include methanol, isopropanol and triethyl-amine. One-step deposition procedures are described for CIS, CIGS and other solar cell devices.

  15. Design of Semiconductor-Based Back Reflectors for High Voc Monolithic Multijunction Solar Cells: Preprint

    SciTech Connect (OSTI)

    Garcia, I.; Geisz, J.; Steiner, M.; Olson, J.; Friedman, D.; Kurtz, S.

    2012-06-01

    State-of-the-art multijunction cell designs have the potential for significant improvement before going to higher number of junctions. For example, the Voc can be substantially increased if the photon recycling taking place in the junctions is enhanced. This has already been demonstrated (by Alta Devices) for a GaAs single-junction cell. For this, the loss of re-emitted photons by absorption in the underlying layers or substrate must be minimized. Selective back surface reflectors are needed for this purpose. In this work, different architectures of semiconductor distributed Bragg reflectors (DBR) are assessed as the appropriate choice for application in monolithic multijunction solar cells. Since the photon re-emission in the photon recycling process is spatially isotropic, the effect of the incident angle on the reflectance spectrum is of central importance. In addition, the DBR structure must be designed taking into account its integration into the monolithic multijunction solar cells, concerning series resistance, growth economics, and other issues. We analyze the tradeoffs in DBR design complexity with all these requirements to determine if such a reflector is suitable to improve multijunction solar cells.

  16. Effects of Spectral Error in Efficiency Measurements of GaInAs-Based Concentrator Solar Cells

    SciTech Connect (OSTI)

    Osterwald, C. R.; Wanlass, M. W.; Moriarty, T.; Steiner, M. A.; Emery, K. A.

    2014-03-01

    This technical report documents a particular error in efficiency measurements of triple-absorber concentrator solar cells caused by incorrect spectral irradiance -- specifically, one that occurs when the irradiance from unfiltered, pulsed xenon solar simulators into the GaInAs bottom subcell is too high. For cells designed so that the light-generated photocurrents in the three subcells are nearly equal, this condition can cause a large increase in the measured fill factor, which, in turn, causes a significant artificial increase in the efficiency. The error is readily apparent when the data under concentration are compared to measurements with correctly balanced photocurrents, and manifests itself as discontinuities in plots of fill factor and efficiency versus concentration ratio. In this work, we simulate the magnitudes and effects of this error with a device-level model of two concentrator cell designs, and demonstrate how a new Spectrolab, Inc., Model 460 Tunable-High Intensity Pulsed Solar Simulator (T-HIPSS) can mitigate the error.

  17. Beijing Sky Solar Investment Management Co | Open Energy Information

    Open Energy Info (EERE)

    Sky Solar Investment Management Co Jump to: navigation, search Name: Beijing Sky Solar Investment & Management Co. Place: Beijing, China Sector: Solar Product: Beijing based...

  18. Shenzhen Xinhonglian Solar Energy Co | Open Energy Information

    Open Energy Info (EERE)

    Xinhonglian Solar Energy Co Jump to: navigation, search Name: Shenzhen Xinhonglian Solar-Energy Co Place: Shenzhen, Guangdong Province, China Sector: Solar Product: China-based...

  19. Electron Solar Energy Formerly Envigra Inc | Open Energy Information

    Open Energy Info (EERE)

    Solar Energy Formerly Envigra Inc Jump to: navigation, search Name: Electron Solar Energy (Formerly Envigra Inc) Place: Miami, Florida Zip: 33137 Sector: Solar Product: US-based...

  20. Xiamen Topunive Technology Co Ltd TP Solar | Open Energy Information

    Open Energy Info (EERE)

    Solar) Place: Xiamen, Fujian Province, China Zip: 361022 Sector: Solar Product: Produce thin-film PV module based flexible solar lighting system, portable and mobile power...

  1. Mulk Renewable Energy Aditya Solar Power Industries JV | Open...

    Open Energy Info (EERE)

    Arab Emirates Sector: Solar Product: UAE-based company that is developing a 200MW solar thermal plant in Sharjah. References: Mulk Renewable Energy & Aditya Solar Power...

  2. Solar Power Company Limited SPC | Open Energy Information

    Open Energy Info (EERE)

    Solar Power Company Limited SPC Jump to: navigation, search Name: Solar Power Company Limited (SPC) Place: Thailand Sector: Solar Product: Thailand-based company that designs,...

  3. SolarEdge Technologies Inc | Open Energy Information

    Open Energy Info (EERE)

    search Name: SolarEdge Technologies Inc Place: Hod Hasharon, Israel Zip: 45240 Sector: Solar Product: Israel-based startup developing a power control system for solar systems,...

  4. SSC HHV Solar Technologies JV | Open Energy Information

    Open Energy Info (EERE)

    Technologies JV Place: Ontario, Canada Sector: Solar Product: Canada-based thin film solar panel manufacturing facility. References: SSC & HHV Solar Technologies JV1 This...

  5. Euro Solar Power Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    Power Pvt Ltd Jump to: navigation, search Name: Euro Solar Power Pvt. Ltd. Place: Mumbai, Maharashtra, India Zip: 400 059 Sector: Solar Product: Mumbai-based solar project...

  6. Solar resources

    SciTech Connect (OSTI)

    Hulstrom, R.L.

    1989-01-01

    Following the 1973 oil embargo, the US government initiated a program to develop and use solar energy. This led to individual programs devoted to developing various solar radiation energy conversion technologies: photovoltaic and solar-thermal conversion devices. Nearly concurrently, it was recognized that understanding the available insolation resources was required to develop and deploy solar energy devices and systems. It was also recognized that the insolation information available at that time (1973) was not adequate to meet the specific needs of the solar energy community. Federal efforts were initiated and conducted to produce new and more extensive information and data. The primary federal agencies that undertook such efforts were the Department of Energy (DOE) and the National Oceanic and Atmospheric Administration (NOAA). NOAA's efforts included activities performed by the National Weather Service (NWS) and the National Climatic Data Center (NCDC). This book has two man objectives: to report some of the insolation energy data, information, and products produced by the federal efforts and to describe how they were produced. Products include data bases, models and algorithms, monitoring networks, instrumentation, and scientific techniques. The scope of products and results does not include all those produced by past federal efforts. The book's scope and subject matter are oriented to support the intent and purpose of the other volumes in this series. In some cases, other pertinent material is presented to provide a more complete coverage of a given subject. 385 refs., 149 figs., 50 tabs.

  7. Membrane-Based Absorption Refrigeration Systems: Nanoengineered Membrane-Based Absorption Cooling for Buildings Using Unconcentrated Solar & Waste Heat

    SciTech Connect (OSTI)

    2010-09-01

    BEETIT Project: UFL is improving a refrigeration system that uses low quality heat to provide the energy needed to drive cooling. This system, known as absorption refrigeration system (ARS), typically consists of large coils that transfer heat. Unfortunately, these large heat exchanger coils are responsible for bulkiness and high cost of ARS. UFL is using new materials as well as system design innovations to develop nanoengineered membranes to allow for enhanced heat exchange that reduces bulkiness. UFL’s design allows for compact, cheaper and more reliable use of ARS that use solar or waste heat.

  8. Solar Newsletter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power ... Sciences Applications National Solar Thermal Test Facility Nuclear Energy ...

  9. Conducting polymers based counter electrodes for dye-sensitized solar cells

    SciTech Connect (OSTI)

    Veerender, P. E-mail: veeru1009@gmail.com; Saxena, Vibha E-mail: veeru1009@gmail.com; Gusain, Abhay E-mail: veeru1009@gmail.com; Jha, P. E-mail: veeru1009@gmail.com; Koiry, S. P. E-mail: veeru1009@gmail.com; Chauhan, A. K. E-mail: veeru1009@gmail.com; Aswal, D. K. E-mail: veeru1009@gmail.com; Gupta, S. K. E-mail: veeru1009@gmail.com

    2014-04-24

    Conducting polymer films were synthesized and employed as an alternative to expensive platinum counter electrodes for dye-sensitized solar cells. poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) thin films were spin-coated and polypyrrole films were electrochemically deposited via cyclic voltammetry method on ITO substrates. The morphology of the films were imaged by SEM and AFM. These films show good catalytic activity towards triiodide reduction as compared to Pt/FTO electrodes. Finally the photovoltaic performance of DSSC fabricated using N3 dye were compared with PT/FTO, PEDOT/ITO, and e-PPy counter electrodes.

  10. OnForce Solar | Open Energy Information

    Open Energy Info (EERE)

    728 East 136th St. Place: Bronx, New York Zip: 10454 Region: Northeast - NY NJ CT PA Area Sector: Renewable Energy Year Founded: 2007 Phone Number: 347 590 5450 Website:...

  11. Sensing mode atomic force microscope

    DOE Patents [OSTI]

    Hough, Paul V. C.; Wang, Chengpu

    2006-08-22

    An atomic force microscope is described having a cantilever comprising a base and a probe tip on an end opposite the base; a cantilever drive device connected to the base; a magnetic material coupled to the probe tip, such that when an incrementally increasing magnetic field is applied to the magnetic material an incrementally increasing force will be applied to the probe tip; a moveable specimen base; and a controller constructed to obtain a profile height of a specimen at a point based upon a contact between the probe tip and a specimen, and measure an adhesion force between the probe tip and the specimen by, under control of a program, incrementally increasing an amount of a magnetic field until a release force, sufficient to break the contact, is applied. An imaging method for atomic force microscopy involving measuring a specimen profile height and adhesion force at multiple points within an area and concurrently displaying the profile and adhesion force for each of the points is also described. A microscope controller is also described and is constructed to, for a group of points, calculate a specimen height at a point based upon a cantilever deflection, a cantilever base position and a specimen piezo position; calculate an adhesion force between a probe tip and a specimen at the point by causing an incrementally increasing force to be applied to the probe tip until the probe tip separates from a specimen; and move the probe tip to a new point in the group.

  12. Sensing mode atomic force microscope

    DOE Patents [OSTI]

    Hough, Paul V.; Wang, Chengpu

    2004-11-16

    An atomic force microscope is described having a cantilever comprising a base and a probe tip on an end opposite the base; a cantilever drive device connected to the base; a magnetic material coupled to the probe tip, such that when an incrementally increasing magnetic field is applied to the magnetic material an incrementally increasing force will be applied to the probe tip; a moveable specimen base; and a controller constructed to obtain a profile height of a specimen at a point based upon a contact between the probe tip and a specimen, and measure an adhesion force between the probe tip and the specimen by, under control of a program, incrementally increasing an amount of a magnetic field until a release force, sufficient to break the contact, is applied. An imaging method for atomic force microscopy involving measuring a specimen profile height and adhesion force at multiple points within an area and concurrently displaying the profile and adhesion force for each of the points is also described. A microscope controller is also described and is constructed to, for a group of points, calculate a specimen height at a point based upon a cantilever deflection, a cantilever base position and a specimen piezo position; calculate an adhesion force between a probe tip and a specimen at the point by causing an incrementally increasing force to be applied to the probe tip until the probe tip separates from a specimen; and move the probe tip to a new point in the group.

  13. A non-contact, thermal noise based method for the calibration of lateral deflection sensitivity in atomic force microscopy

    SciTech Connect (OSTI)

    Mullin, Nic Hobbs, Jamie K.

    2014-11-15

    Calibration of lateral forces and displacements has been a long standing problem in lateral force microscopies. Recently, it was shown by Wagner et al. that the thermal noise spectrum of the first torsional mode may be used to calibrate the deflection sensitivity of the detector. This method is quick, non-destructive and may be performed in situ in air or liquid. Here we make a full quantitative comparison of the lateral inverse optical lever sensitivity obtained by the lateral thermal noise method and the shape independent method developed by Anderson et al. We find that the thermal method provides accurate results for a wide variety of rectangular cantilevers, provided that the geometry of the cantilever is suitable for torsional stiffness calibration by the torsional Sader method, in-plane bending of the cantilever may be eliminated or accounted for and that any scaling of the lateral deflection signal between the measurement of the lateral thermal noise and the measurement of the lateral deflection is eliminated or corrected for. We also demonstrate that the thermal method may be used to characterize the linearity of the detector signal as a function of position, and find a deviation of less than 8% for the instrument used.

  14. Grid Inertial Response-Based Probabilistic Determination of Energy Storage System Capacity Under High Solar Penetration

    SciTech Connect (OSTI)

    Yue, Meng; Wang, Xiaoyu

    2015-07-01

    It is well-known that responsive battery energy storage systems (BESSs) are an effective means to improve the grid inertial response to various disturbances including the variability of the renewable generation. One of the major issues associated with its implementation is the difficulty in determining the required BESS capacity mainly due to the large amount of inherent uncertainties that cannot be accounted for deterministically. In this study, a probabilistic approach is proposed to properly size the BESS from the perspective of the system inertial response, as an application of probabilistic risk assessment (PRA). The proposed approach enables a risk-informed decision-making process regarding (1) the acceptable level of solar penetration in a given system and (2) the desired BESS capacity (and minimum cost) to achieve an acceptable grid inertial response with a certain confidence level.

  15. Highly efficient organic multi-junction solar cells with a thiophene based donor material

    SciTech Connect (OSTI)

    Meerheim, Rico Krner, Christian; Leo, Karl

    2014-08-11

    The efficiency of organic solar cells can be increased by serial stacked subcells even upon using the same absorber material. For the multi-junction devices presented here, we use the small molecule donor material DCV5T-Me. The subcell currents were matched by optical transfer matrix simulation, allowing an efficiency increase from 8.3% for a single junction up to 9.7% for a triple junction cell. The external quantum efficiency of the subcells, measured under appropriate light bias illumination, is spectrally shifted due to the microcavity of the complete stack, resulting in a broadband response and an increased cell current. The increase of the power conversion efficiency upon device stacking is even stronger for large area cells due to higher influence of the resistance of the indium tin oxide anode, emphasizing the advantage of multi-junction devices for large-area applications.

  16. Grid Inertial Response-Based Probabilistic Determination of Energy Storage System Capacity Under High Solar Penetration

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Yue, Meng; Wang, Xiaoyu

    2015-07-01

    It is well-known that responsive battery energy storage systems (BESSs) are an effective means to improve the grid inertial response to various disturbances including the variability of the renewable generation. One of the major issues associated with its implementation is the difficulty in determining the required BESS capacity mainly due to the large amount of inherent uncertainties that cannot be accounted for deterministically. In this study, a probabilistic approach is proposed to properly size the BESS from the perspective of the system inertial response, as an application of probabilistic risk assessment (PRA). The proposed approach enables a risk-informed decision-making processmore » regarding (1) the acceptable level of solar penetration in a given system and (2) the desired BESS capacity (and minimum cost) to achieve an acceptable grid inertial response with a certain confidence level.« less

  17. Australian Solar Institute | Open Energy Information

    Open Energy Info (EERE)

    search Name: Australian Solar Institute Place: Newcastle, New South Wales, Australia Zip: 2300 Sector: Solar Product: New South Wales-based institute providing support...

  18. Amcor Solar Energies Ltd | Open Energy Information

    Open Energy Info (EERE)

    Energies Ltd Jump to: navigation, search Name: Amcor Solar Energies Ltd Place: Ashdod, Israel Zip: 77136 Sector: Solar Product: Israel-based subsidiary of the Ashtrom Group,...

  19. Buzitka Solar AS | Open Energy Information

    Open Energy Info (EERE)

    Buzitka Solar AS Jump to: navigation, search Name: Buzitka Solar AS Place: Buzitka, Slovakia Zip: 985 41 Product: Slovakia based developer of PV projects. Coordinates: 48.307735,...

  20. Stea Divisione Energia Solare | Open Energy Information

    Open Energy Info (EERE)

    Italy-based company present alternative energy, offering engineering services, marketing and installation of solar PV and solar thermal projects. References: Stea Divisione...

  1. Commercial Solar Ventures | Open Energy Information

    Open Energy Info (EERE)

    Solar Product: Portland based company that specializes in commercial scale solar installations throughout Oregon. Coordinates: 45.511795, -122.675629 Show Map Loading map......

  2. CSG Solar AG | Open Energy Information

    Open Energy Info (EERE)

    Germany Zip: 6766 Sector: Solar Product: Manufacture of solar modules based on Crystalline Silicon on Glass (CSG) technology Coordinates: 50.70348, 12.8498 Show Map...

  3. First Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    First Solar Inc Jump to: navigation, search Name: First Solar Inc Place: Phoenix, Arizona Zip: 85040 Product: A Phoenix-based manufacturer of cadmium telluride modules and...

  4. Gamma Solar Corporation | Open Energy Information

    Open Energy Info (EERE)

    Solar Corporation Jump to: navigation, search Name: Gamma Solar Corporation Place: Weston, Florida Zip: 33326 Product: Florida-based firm developing a technology for bifacial and...

  5. Advent Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    Solar Inc Jump to: navigation, search Name: Advent Solar Inc Place: Albuquerque, New Mexico Zip: 87106 Product: Albuquerque-based manufacturer of crystalline silicon PV cells and...

  6. BSC Solar Sro | Open Energy Information

    Open Energy Info (EERE)

    BSC Solar Sro Jump to: navigation, search Name: BSC Solar Sro Place: Greslove Myto, Czech Republic Zip: 67156 Product: Czech Republic-based developer of PV projects. References:...

  7. AuantumSolar | Open Energy Information

    Open Energy Info (EERE)

    AuantumSolar Jump to: navigation, search Name: AuantumSolar Place: Montpellier, France Zip: 34695 Product: French developer of inorganic dye-based PV cells References:...

  8. Ammini Solar Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    Trivandrum, Kerala, India Zip: 695 582 Sector: Solar Product: Kerala-based producer of solar lighting, heating, and cooking products for domestic and commercial use. References:...

  9. Jupiter Solar Power Ltd | Open Energy Information

    Open Energy Info (EERE)

    Solar Power Ltd Jump to: navigation, search Name: Jupiter Solar Power Ltd Place: Kolkata, West Bengal, India Zip: 700012 Product: India-based subsidiary of Jupiter International...

  10. Solar Electric Solutions LLC | Open Energy Information

    Open Energy Info (EERE)

    Electric Solutions LLC Jump to: navigation, search Name: Solar Electric Solutions, LLC Place: Woodland Hills, California Zip: 91364 Sector: Solar Product: California-based...

  11. Ingenia Solar Energy | Open Energy Information

    Open Energy Info (EERE)

    Ingenia Solar Energy Jump to: navigation, search Name: Ingenia Solar Energy Place: Madrid, Spain Zip: 28034 Product: Spain-based technical consultant for PV projects. Coordinates:...

  12. Advanced Solar Photonics | Open Energy Information

    Open Energy Info (EERE)

    Advanced Solar Photonics Place: Lake Mary, Florida Zip: 32746 Product: Florida-based thin film PV module manufacturer. References: Advanced Solar Photonics1 This article is...

  13. Solar Electrical Vehicles | Open Energy Information

    Open Energy Info (EERE)

    Electrical Vehicles Jump to: navigation, search Name: Solar Electrical Vehicles Place: Westlake Village, California Zip: 91361 Sector: Solar, Vehicles Product: US-based...

  14. Solar Millennium LLC USA | Open Energy Information

    Open Energy Info (EERE)

    LLC USA Jump to: navigation, search Name: Solar Millennium LLC (USA) Place: Berkeley, California Sector: Solar Product: California-based STEG power plant developer, parabolic...

  15. Enertis Solar SL | Open Energy Information

    Open Energy Info (EERE)

    Enertis Solar SL Jump to: navigation, search Name: Enertis Solar SL Place: Madrid, Spain Zip: 28703 Product: Spain-based technical consultancy for PV projects. Coordinates:...

  16. Gehrlicher Solar AG | Open Energy Information

    Open Energy Info (EERE)

    96465 Sector: Solar Product: Germany-based company that plans, builds and markets photovoltaic and solar thermal plants. It consults for local, private and environmental...

  17. Visible Light Solar Technologies | Open Energy Information

    Open Energy Info (EERE)

    Solar Technologies Place: Albuquerque, New York Zip: 87113 Product: New Mexico-based LED lighting fixture maker. References: Visible Light Solar Technologies1 This article is...

  18. Tessera Solar (Texas) | Open Energy Information

    Open Energy Info (EERE)

    77002 Region: Texas Area Sector: Solar Product: Developer of utility scale solar power plants based on dish-Stirling engine designs Website: www.tesserasolar.com Coordinates:...

  19. QC Solar Suzhou Corporation | Open Energy Information

    Open Energy Info (EERE)

    Jiangsu Province, China Zip: 215123 Sector: Solar Product: Suzhou-based solar PV electronics manufacturing firm. Coordinates: 31.3092, 120.613121 Show Map Loading map......

  20. Denver Public Schools Get Solar Energy System

    Broader source: Energy.gov [DOE]

    Main Street Power, a solar development company based in Boulder, is installing solar photovoltaic systems on the rooftops of 12 Denver Public Schools.

  1. RAcell Solar AS | Open Energy Information

    Open Energy Info (EERE)

    AS Place: Copenhagen, Denmark Zip: 1820 Sector: Solar Product: Denmark based producer of solar cells and modules; also provides turnkey system installation for PV and BIPV....

  2. Summary of Time Period-Based and Other Approximation Methods for Determining the Capacity Value of Wind and Solar in the United States: September 2010 - February 2012

    SciTech Connect (OSTI)

    Rogers, J.; Porter, K.

    2012-03-01

    This paper updates previous work that describes time period-based and other approximation methods for estimating the capacity value of wind power and extends it to include solar power. The paper summarizes various methods presented in utility integrated resource plans, regional transmission organization methodologies, regional stakeholder initiatives, regulatory proceedings, and academic and industry studies. Time period-based approximation methods typically measure the contribution of a wind or solar plant at the time of system peak - sometimes over a period of months or the average of multiple years.

  3. Installation-Restoration Program. Phase 2. Confirmation/quantification, Stage 2 for Seymour Johnson Air Force Base, North Carolina. Volume 1. Final report, July 1986-November 1988

    SciTech Connect (OSTI)

    Alexander, W.J.; Winters, S.L.; Guthrie, S.A.

    1988-11-01

    A Phase II, Stage 2 survey has been conducted at the Seymour Johnson Air Force Base under the Department of Defense's Installation Restoration Program (IRP). Six sites were identified by the Air Force for further study and include: Fire Training Area No. 3 (Site 1); Landfill No. 4 (Site 2); Landfill No. 1 (Site 3); Landfill No. 3 (Site 4); DPDO Waste Storage Area (Site 5); and Coal Pile Storage Area (Site 6). The evaluation primarily included the drilling of soil test borings, the installation, development, and sampling of new monitoring wells, resampling of selected Stage 1 monitoring wells, and the analysis of soil and water samples. A thin surficial aquifer was encountered at shallow depths beneath the sites that border the southeastern side of Stoney Creek. The surficial aquifer is contaminated at Sites 1, 2, 4, and 5 as a result of Base activities. Ground-water flow in the surficial aquifer is primarily horizontal and discharges into Stoney Creek along the northwestern limit of the Base. The major environmental concern revealed by this evaluation is the potential discharge of contaminated water from the surficial aquifer into Stoney Creek.

  4. SnO{sub 2} films: In-situ template-sacrificial growth and photovoltaic property based on SnO{sub 2}/poly(3-hexyl-thiophene) for hybrid solar cell

    SciTech Connect (OSTI)

    Zhang, Yange; Li, Pinjiang; Xu, Xiaoyun; Wang, Min; Shen, Jinfeng; Zhang, Fujuan; Zheng, Zhi

    2015-10-15

    Highlights: • SnO{sub 2} nanocrystals/thin films were fabricated on ITO glass substrate from preformed SnS thin film as sacrificial template. • The SnO{sub 2} film and SnO{sub 2}/P3HT was characterized by several techniques. • The new hybrid solar cell device was based on the hybrid thin film of SnO{sub 2} NCs and P3HT composites. - Abstract: we described a facile in-situ wet chemical method to prepare SnO{sub 2} thin film on ITO glass substrate from preformed SnS thin film as sacrificial template. The chemical conversion process of SnS to SnO{sub 2} was studied. The SnO{sub 2} film and SnO{sub 2}/P3HT was characterized by several techniques, such as powder X-ray diffract meter (XRD), Raman spectrometer, scanning electron microscope (SEM), atomic force microscope (AFM) and UV–vis spectrophotometer in detail. The new SnO{sub 2}/P3HT hybrid solar cell device showed an open-circuit voltage of 0.185 V, a short-circuit current density of 0.366 mA/cm{sup 2} and a fill factor of 0.247, corresponding to a power conversion efficiency of 0.0167%.

  5. SolarRoofs com | Open Energy Information

    Open Energy Info (EERE)

    95608 Sector: Solar Product: California-based manufacturer of the patented Skyline solar water heating systems. References: SolarRoofs.com1 This article is a stub. You can help...

  6. Canadian Solar Japan KK | Open Energy Information

    Open Energy Info (EERE)

    Japan KK Jump to: navigation, search Name: Canadian Solar Japan KK Place: Shinjuku-ku, Tokyo, Japan Zip: 160-0022 Sector: Solar Product: Tokyo-based subsidiary of Canadian Solar,...

  7. Formosun Solar Corp | Open Energy Information

    Open Energy Info (EERE)

    Corp. Place: Hsinchu County, Taiwan Zip: 303-51 Sector: Solar Product: Thin-film solar cell producer based in Taiwan. References: Formosun Solar Corp.1 This article is a stub....

  8. Sun Bear Solar Ltd | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search Name: Sun Bear Solar Ltd Place: Hong Kong Sector: Solar Product: Hong Kong-based firm that manufactures solar product equipment, such as PV glass,...

  9. Filsol Solar Ltd | Open Energy Information

    Open Energy Info (EERE)

    Kingdom Zip: SA15 5RA Sector: Solar Product: Wales-based manufacturer and installer of solar passive heating systems and PV modules. References: Filsol Solar Ltd1 This article...

  10. Solar Energy Initiatives Inc | Open Energy Information

    Open Energy Info (EERE)

    Initiatives Inc Jump to: navigation, search Name: Solar Energy Initiatives Inc Place: St. Johns, Florida Zip: 32082 Sector: Solar Product: US-based PV and solar thermal and PV...

  11. K Star Solar | Open Energy Information

    Open Energy Info (EERE)

    Solar Jump to: navigation, search Name: K-Star Solar Place: New York Product: Long Island-based PV systems installer. References: K-Star Solar1 This article is a stub. You can...

  12. GA SNC Solar | Open Energy Information

    Open Energy Info (EERE)

    GA-SNC Solar Place: Nevada Sector: Solar Product: Nevada-based PV project developer and joint venture of GA-Solar North America and Sierra Nevada Corp. References: GA-SNC...

  13. Solar Style Inc | Open Energy Information

    Open Energy Info (EERE)

    Baltimore, Maryland Zip: 21244 Sector: Solar Product: US-based manufacturer of solar battery recharger. References: Solar Style Inc1 This article is a stub. You can help OpenEI...

  14. Solar Project Solutions | Open Energy Information

    Open Energy Info (EERE)

    Solutions Place: California Sector: Solar Product: US-based JV to build solar-power plants in California. References: Solar Project Solutions1 This article is a stub. You can...

  15. SolarCity Corp | Open Energy Information

    Open Energy Info (EERE)

    Place: Foster City, California Zip: 94404 Sector: Solar Product: US-based designer and installer of solar systems for domestic and commercial use. References: SolarCity Corp1...

  16. The Solar Center Inc | Open Energy Information

    Open Energy Info (EERE)

    Center Inc Place: New Jersey, New Jersey Zip: 7834 Sector: Solar Product: US-based PV and solar passive system installer. References: The Solar Center Inc1 This article is a...

  17. Aora Energy Aora Solar | Open Energy Information

    Open Energy Info (EERE)

    Aora Energy Aora Solar Jump to: navigation, search Name: Aora Energy (Aora Solar) Place: Yavne, Israel Zip: 81227 Sector: Solar Product: Israel-based company that has developed a...

  18. Euro Solar Parks Inc | Open Energy Information

    Open Energy Info (EERE)

    Parks Inc Jump to: navigation, search Name: Euro Solar Parks Inc Place: Ho-ho-Kus, New Jersey Zip: 7423 Sector: Solar Product: New Jersey-based solar developer focused on...

  19. Organic Based Nanocomposite Solar Cells: Cooperative Research and Development Final Report, CRADA Number CRD-04-145

    SciTech Connect (OSTI)

    Olson, D.

    2013-01-01

    This CRADA will focus on the development of organic-based solar cells. Key interfacial issues in these cells will be investigated. In this rapidly emerging technology, it is increasingly clear that cell architecture will need to be at the nanoscale and the interfacial issues between organic elements (small molecule and polymer), transparent conducting oxides, and contact metallizations are critical. Thus this work will focus on the development of high surface area and nanostructured nanocarpets of inorganic oxides, the development of appropriate surface binding/acceptor molecules for the inorganic/organic interface, and the development of next-generation organic materials. Work will be performed in all three areas jointly at NREL and Konarka (with their partner in the third area of the University of Delaware). Results should be more rapid progress toward cheap large-area photovoltaic cells.

  20. SunRider Solar LLC | Open Energy Information

    Open Energy Info (EERE)

    Solar Product: Arizona-based solar services company providing turnkey solar installations. References: SunRider Solar LLC1 This article is a stub. You can help OpenEI by...

  1. Galip Solar GmbH | Open Energy Information

    Open Energy Info (EERE)

    Galip Solar GmbH Jump to: navigation, search Name: Galip Solar GmbH Place: Germany Sector: Services, Solar Product: Germany-based solar project developer, offering end user...

  2. AxunTek Solar Energy | Open Energy Information

    Open Energy Info (EERE)

    AxunTek Solar Energy Jump to: navigation, search Name: AxunTek Solar Energy Place: Taiwan Sector: Solar Product: Taiwan-based CIGS thin film solar cell producer. References:...

  3. Sangle Solar Energy Co Ltd | Open Energy Information

    Open Energy Info (EERE)

    Sangle Solar Energy Co Ltd Jump to: navigation, search Name: Sangle Solar Energy Co Ltd Place: Jinan, Shandong Province, China Sector: Solar Product: China-based solar water heater...

  4. Sunlight Solar Energy Inc SSE | Open Energy Information

    Open Energy Info (EERE)

    Solar Energy Inc SSE Jump to: navigation, search Name: Sunlight Solar Energy, Inc (SSE) Place: Bend, Oregon Zip: 97701 Sector: Solar Product: Bend (OR)-based solar integration firm...

  5. Solar Kabel GmbH | Open Energy Information

    Open Energy Info (EERE)

    Kabel GmbH Jump to: navigation, search Name: Solar-Kabel GmbH Place: Germany Sector: Solar Product: Germany-based solar PV cable manufacturer. References: Solar-Kabel GmbH1 This...

  6. Solar Utility SpA | Open Energy Information

    Open Energy Info (EERE)

    Utility SpA Jump to: navigation, search Name: Solar Utility SpA Place: Italy Sector: Solar Product: Italy-based solar PV project developer. References: Solar Utility SpA1 This...

  7. Solar Installation Labor Market Analysis

    SciTech Connect (OSTI)

    Friedman, B.; Jordan, P.; Carrese, J.

    2011-12-01

    The potential economic benefits of the growing renewable energy sector have led to increased federal, state, and local investments in solar industries, including federal grants for expanded workforce training for U.S. solar installers. However, there remain gaps in the data required to understand the size and composition of the workforce needed to meet the demand for solar power. Through primary research on the U.S. solar installation employer base, this report seeks to address that gap, improving policymakers and other solar stakeholders understanding of both the evolving needs of these employers and the economic opportunity associated with solar market development. Included are labor market data covering current U.S. employment, expected industry growth, and employer skill preferences for solar installation-related occupations. This study offers an in-depth look at the solar installation sectors. A study published by the Solar Foundation in October 2011 provides a census of labor data across the entire solar value chain.

  8. High Efficiency and High Rate Deposited Amorphous Silicon-Based Solar Cells: Final Technical Report, 1 September 2001--6 March 2005

    SciTech Connect (OSTI)

    Deng, X.

    2006-01-01

    The objectives for the University of Toledo are to: (1) establish a transferable knowledge and technology base for fabricating high-efficiency triple-junction a-Si-based solar cells, and (2) develop high-rate deposition techniques for the growing a-Si-based and related alloys, including poly-Si, c-Si, a-SiGe, and a-Si films and photovoltaic devices with these materials.

  9. Back reflectors based on buried Al{sub 2}O{sub 3} for enhancement of photon recycling in monolithic, on-substrate III-V solar cells

    SciTech Connect (OSTI)

    García, I.; Ward, J. S.; Steiner, M. A.; Geisz, J. F.; Kurtz, S. R.

    2014-09-29

    Photon management has been shown to be a fruitful way to boost the open circuit voltage and efficiency of high quality solar cells. Metal or low-index dielectric-based back reflectors can be used to confine the reemitted photons and enhance photon recycling. Gaining access to the back of the solar cell for placing these reflectors implies having to remove the substrate, with the associated added complexity to the solar cell manufacturing. In this work, we analyze the effectiveness of a single-layer reflector placed at the back of on-substrate solar cells, and assess the photon recycling improvement as a function of the refractive index of this layer. Al{sub 2}O{sub 3}-based reflectors, created by lateral oxidation of an AlAs layer, are identified as a feasible choice for on-substrate solar cells, which can produce a V{sub oc} increase of around 65% of the maximum increase attainable with an ideal reflector. The experimental results obtained using prototype GaAs cell structures show a greater than two-fold increase in the external radiative efficiency and a V{sub oc} increase of ∼2% (∼18 mV), consistent with theoretical calculations. For GaAs cells with higher internal luminescence, this V{sub oc} boost is calculated to be up to 4% relative (36 mV), which directly translates into at least 4% higher relative efficiency.

  10. Prothea Solar | Open Energy Information

    Open Energy Info (EERE)

    Italy Zip: 20100 Sector: Solar Product: Milan-based greenfield developer and turn key provider of solar energy power plants. Coordinates: 45.468945, 9.18103 Show Map...

  11. Astrum Solar | Open Energy Information

    Open Energy Info (EERE)

    Solar Place: Annapolis Junction, Maryland Zip: 20701 Product: Maryland-based PV systems installer. References: Astrum Solar1 This article is a stub. You can help OpenEI by...

  12. Novagen Solar | Open Energy Information

    Open Energy Info (EERE)

    Novagen Solar Jump to: navigation, search Name: Novagen Solar Place: Toronto, Ontario, Canada Zip: M8X 2Y8 Product: Marketer and distributor of PV products based in Toronto....

  13. Solar Easements

    Broader source: Energy.gov [DOE]

    New Hampshire's "solar skyspace easement" provisions allow property owners to create solar easements in order to create and preserve a right to unobstructed access to solar energy. Easements remain...

  14. Solar Power

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solar Power Solar Power Project Opportunities Abound in the Region The WIPP site is receives abundant solar energy with 6-7 kWhsq meter power production potential As the ...

  15. Solar Newsletter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Goes Big: Launching the California Valley Solar Ranch Solar Goes Big: Launching the California Valley Solar Ranch October 31, 2013 - 4:14pm Addthis The California Valley Solar Ranch produces clean, renewable electricity at the scale of traditional power plants. | Photo courtesy of SunPower. The California Valley Solar Ranch produces clean, renewable electricity at the scale of traditional power plants. | Photo courtesy of SunPower. Aerial shot of the California Valley Solar Ranch in

  16. Conservation and solar guidelines

    SciTech Connect (OSTI)

    Balcomb, J.D.

    1986-01-01

    Guidelines are given for selecting R-values and infiltration levels, and determining the size of the solar collection area for passive solar buildings. The guidelines are based on balancing the incremental cost/benefit of conservation and passive solar strategies. Tables are given for 90 cities in the United States and the results are also displayed on maps. The procedures are developed in an appendix, which gives the cost assumptions used and explains how to develop different guidelines for different costs.

  17. Developing countries: solar energy. January 1976-May 1981 (citations from the Energy Data Base). Report for Jan 76-May 81

    SciTech Connect (OSTI)

    Not Available

    1981-05-01

    This retrospective bibliography contains citations concerning existing and potential utilization of solar energy in developing countries. Commercial, economic, and technological aspects of solar energy devices, equipment, and systems for the third world are covered along with a wide variety of applications for them. The transfer of solar technology from developed nations to the third world is also covered. (Contains 157 citations fully indexed and including a title list.)

  18. Solar Decathlon

    Broader source: Energy.gov [DOE]

    The Energy Department's Solar Decathlon challenges collegiate teams to design, build and operate solar-powered houses that are cost effective, energy efficient and attractive.

  19. Solar Newsletter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Events, Photovoltaic, Renewable Energy, Research & Capabilities, Solar, Solar Newsletter, SunShot, ... The system will be monitored and tested to collect a range of data ...

  20. Solar Decathlon

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... and workforce development opportunity for ... around the world: Solar Decathlon China 2013, Solar Decathlon ... and two-way power flow for operation of ...

  1. EERE SunShot's SHINES Program: Enabling a Rapidly Solarizing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... SunShot Shines On Packed House Solar Community Comes Out in Full Force for SunShot Grand Challenge Summit SunShot Installs Solar Energy System on Local Habitat for Humanity Home

  2. Semiconductor wire array structures, and solar cells and photodetectors based on such structures

    DOE Patents [OSTI]

    Kelzenberg, Michael D.; Atwater, Harry A.; Briggs, Ryan M.; Boettcher, Shannon W.; Lewis, Nathan S.; Petykiewicz, Jan A.

    2014-08-19

    A structure comprising an array of semiconductor structures, an infill material between the semiconductor materials, and one or more light-trapping elements is described. Photoconverters and photoelectrochemical devices based on such structure also described.

  3. Simulation of quantum dots size and spacing effect for intermediate band solar cell application based on InAs quantum dots arrangement in GaAs

    SciTech Connect (OSTI)

    Hendra, P. I. B. Rahayu, F. Darma, Y.

    2014-03-24

    Intermediate band solar cell (IBSC) has become a promising technology in increasing solar cell efficiency. In this work we compare absorption coefficient profile between InAs quantum dots with GaAs bulk. We calculate the efficiency of GaAs bulk and GaAs doped with 2, 5, and 10 nm InAs quantum dot. Effective distances in quantum dot arrangement based on electron tunneling consideration were also calculated. We presented a simple calculation method with low computing power demand. Results showed that arrangement of quantum dot InAs in GaAs can increase solar cell efficiency from 23.9 % initially up to 60.4%. The effective distance between two quantum dots was found 2 nm in order to give adequate distance to prevent electron tunneling and wave functions overlap.

  4. Region Solar Inc Solar Inc California Renewable Energy Solar...

    Open Energy Info (EERE)

    Point Drive Fort Collins Colorado Solar Solar cell passive solar architectural glass solar grid tie inverter semiconductor flat panel display data storage http www advanced...

  5. Storm-water characterization and lagoon sediment analysis, Grand Forks Air Force Base, North Dakota. Final report

    SciTech Connect (OSTI)

    Garland, J.G.; Vaughn, R.W.; Scott, P.T.

    1990-08-01

    Sampling was conducted in the wastewater treatment lagoons and stormwater runoff at Grand Forks AFB. The base was concerned about whether the unlined lagoons were creating a potential groundwater contamination problem and whether their stormwater runoff met North Dakota state stream standards. Lagoon sediment did not contain Extraction Procedure hazardous chemicals. Stormwater runoff exceeded state standards for boron, phosphates, and phenols and contained trace levels of methylene chloride. Characterization of lagoon influent showed it to be generally representative of domestic sewage, but also contained trace levels of boron, phenols, toluene, cyanide, chloroform, methylene chloride and ethyl benzene.

  6. Solar thermal aircraft

    DOE Patents [OSTI]

    Bennett, Charles L.

    2007-09-18

    A solar thermal powered aircraft powered by heat energy from the sun. A heat engine, such as a Stirling engine, is carried by the aircraft body for producing power for a propulsion mechanism, such as a propeller. The heat engine has a thermal battery in thermal contact with it so that heat is supplied from the thermal battery. A solar concentrator, such as reflective parabolic trough, is movably connected to an optically transparent section of the aircraft body for receiving and concentrating solar energy from within the aircraft. Concentrated solar energy is collected by a heat collection and transport conduit, and heat transported to the thermal battery. A solar tracker includes a heliostat for determining optimal alignment with the sun, and a drive motor actuating the solar concentrator into optimal alignment with the sun based on a determination by the heliostat.

  7. Bosch Solar Energy AG former ErSol Solar Energy AG | Open Energy...

    Open Energy Info (EERE)

    AG former ErSol Solar Energy AG Jump to: navigation, search Name: Bosch Solar Energy AG (former ErSol Solar Energy AG) Place: Erfurt, Germany Zip: D-99099 Product: Germany-based...

  8. New Morphological Paradigm Uncovered in Organic Solar Cells

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    layer. This improved understanding will guide the future development and optimization of organic solar cells by reducing laborious trial-and-error development and forcing other...

  9. Solar Radiometric Data Quality Assessment of SIRS, SKYRAD and...

    Office of Scientific and Technical Information (OSTI)

    is the driving force for the earth's weather and climate. Understanding the elements of this dynamic energy balance requires accurate measurements of broadband solar irradiance. ...

  10. Solar Outreach Partnership | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Outreach Partnership Solar Outreach Partnership The Solar Outreach Partnership (SolarOPs) is designed to help accelerate solar energy adoption on the local level by providing timely and actionable information to local governments. Funded by the U.S. Department of Energy (DOE) SunShot Initiative, SolarOPs achieves its goals through a mix of educational workshops, peer-to-peer sharing opportunities, research-based reports, and online resources. To perform the work of SolarOPs, DOE selected teams

  11. Hydrologic transport of depleted uranium associated with open air dynamic range testing at Los Alamos National Laboratory, New Mexico, and Eglin Air Force Base, Florida

    SciTech Connect (OSTI)

    Becker, N.M.; Vanta, E.B.

    1995-05-01

    Hydrologic investigations on depleted uranium fate and transport associated with dynamic testing activities were instituted in the 1980`s at Los Alamos National Laboratory and Eglin Air Force Base. At Los Alamos, extensive field watershed investigations of soil, sediment, and especially runoff water were conducted. Eglin conducted field investigations and runoff studies similar to those at Los Alamos at former and active test ranges. Laboratory experiments complemented the field investigations at both installations. Mass balance calculations were performed to quantify the mass of expended uranium which had transported away from firing sites. At Los Alamos, it is estimated that more than 90 percent of the uranium still remains in close proximity to firing sites, which has been corroborated by independent calculations. At Eglin, we estimate that 90 to 95 percent of the uranium remains at test ranges. These data demonstrate that uranium moves slowly via surface water, in both semi-arid (Los Alamos) and humid (Eglin) environments.

  12. Link Force Holdings Ltd | Open Energy Information

    Open Energy Info (EERE)

    search Name: Link Force Holdings Ltd Place: China Product: China-based energy saving LED street light maker. References: Link Force Holdings Ltd1 This article is a stub. You...

  13. Titanium dioxide/silicon hole-blocking selective contact to enable double-heterojunction crystalline silicon-based solar cell

    SciTech Connect (OSTI)

    Nagamatsu, Ken A. Man, Gabriel; Jhaveri, Janam; Berg, Alexander H.; Kahn, Antoine; Wagner, Sigurd; Sturm, James C.; Avasthi, Sushobhan; Sahasrabudhe, Girija; Schwartz, Jeffrey

    2015-03-23

    In this work, we use an electron-selective titanium dioxide (TiO{sub 2}) heterojunction contact to silicon to block minority carrier holes in the silicon from recombining at the cathode contact of a silicon-based photovoltaic device. We present four pieces of evidence demonstrating the beneficial effect of adding the TiO{sub 2} hole-blocking layer: reduced dark current, increased open circuit voltage (V{sub OC}), increased quantum efficiency at longer wavelengths, and increased stored minority carrier charge under forward bias. The importance of a low rate of recombination of minority carriers at the Si/TiO{sub 2} interface for effective blocking of minority carriers is quantitatively described. The anode is made of a poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) heterojunction to silicon which forms a hole selective contact, so that the entire device is made at a maximum temperature of 100 °C, with no doping gradients or junctions in the silicon. A low rate of recombination of minority carriers at the Si/TiO{sub 2} interface is crucial for effective blocking of minority carriers. Such a pair of complementary carrier-selective heterojunctions offers a path towards high-efficiency silicon solar cells using relatively simple and near-room temperature fabrication techniques.

  14. Optical and carrier transport properties of graphene oxide based crystalline-Si/organic Schottky junction solar cells

    SciTech Connect (OSTI)

    Khatri, I.; Tang, Z.; Hiate, T.; Liu, Q.; Ishikawa, R.; Ueno, K.; Shirai, H.

    2013-12-21

    We investigated the graphene oxide (GO) based n-type crystalline silicon (c-Si)/conductive poly(ethylene dioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) Schottky junction devices with optical characterization and carrier transport measurement techniques. The optical transmittance in the UV region decreased markedly for the films with increasing the concentration of GO whereas it increased markedly in the visible-infrared regions. Spectroscopic ellipsometry revealed that the ordinary and extraordinary index of refraction increased with increasing the concentration of GO. The hole mobility also increased from 1.14 for pristine film to 1.85 cm{sup 2}/V s for the 1215?wt. % GO modified film with no significant increases of carrier concentration. The highest conductivity was found for a 15?wt. % GO modified PEDOT:PSS film: the c-Si/PEDOT:PSS:GO device using this sample exhibited a relatively high power conversion efficiency of 11.04%. In addition, the insertion of a 23?nm-thick GO thin layer at the c-Si/PEDOT:PSS interface suppressed the carrier recombination efficiency of dark electron and photo-generated hole at the anode, resulting in the increased photovoltaic performance. This study indicates that the GO can be good candidates for hole transporting layer of c-Si/PEDOT:PSS Schottky junction solar cell.

  15. Mojave Solar Park Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Solar Park Solar Power Plant Jump to: navigation, search Name Mojave Solar Park Solar Power Plant Facility Mojave Solar Park Sector Solar Facility Type Concentrating Solar Power...

  16. Nevada Solar One Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Solar One Solar Power Plant Jump to: navigation, search Name Nevada Solar One Solar Power Plant Facility Nevada Solar One Sector Solar Facility Type Concentrating Solar Power...

  17. Starwood Solar I Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Starwood Solar I Solar Power Plant Jump to: navigation, search Name Starwood Solar I Solar Power Plant Facility Starwood Solar I Sector Solar Facility Type Concentrating Solar...

  18. Solar Construction Permitting Standards

    Office of Energy Efficiency and Renewable Energy (EERE)

    Two bills signed in 2012 place limits on the fees that cities, counties, cities and counties, and charter cities can charge for a solar permit. AB 1801 specifies that a local government cannot base...

  19. Electroabsorption and transport measurements and modeling in amorphous-silicon-based solar cells: Phase I technical progress report, 24 March 1998--23 March 1999

    SciTech Connect (OSTI)

    Schiff, E. A.; Lyou, J.; Kopidakis, N.; Rao, P.; Yuan, Q.

    1999-12-17

    This report describes work done by the Syracuse University during Phase 1 of this subcontract. Researchers performed work in the following areas: (1) In ``Electroabsorption measurements and built-in potentials in a-Si:H-based solar cells and devices'', researchers obtained an estimate of Vbi = 1.17 V in cells with a-SiGe:H absorber layers from United Solar Systems Corp. (2) In ``Solar cell modeling employing the AMPS computer program'', researchers began operating a simple AMPS modeling site and explored the effect of conduction bandtail width on Voc computed analytical approximations and the AMPS program. The quantitative differences between the two procedures are discussed. (3) In ``Drift mobility measurements in a-Si:H made with high hydrogen dilution'', researchers measured electron and hole mobilities in several n/i/Ni (semitransparent) cells from Pennsylvania State University with a-Si absorber layers made under maximal hydrogen dilution and found a modest increase in hole mobility in these materials compared to conventional a-Si:H. (4) In ``Electroabsorption spectroscopy in solar cells'', researchers discovered and interpreted an infrared absorption band near 1.0 eV, which they believe is caused by dopants and defects at the n/i interface of cells, and which also has interesting implications for the nature of electroabsorption and for the doping mechanism in n-type material.

  20. AIR FORCE SPECIAL WEAPONS CENTER

    Office of Legacy Management (LM)

    HEADQUARTERS aII?y 9 AIR FORCE SPECIAL WEAPONS CENTER 1 AIR FORCE SYSTEMS COMMAND . - KlRTlAND AIR FORCE BASE, NEW MEXICO - k FINAL REPORT O N AIR FORCE PARTICIPATION PROJECT RULISON .1 O c t o b e r 1969 P r e p a r e d by : CONT INENTAL TEST D I V I S ION DIRECTORATE OF NUCLEAR FIELD OPERATIONS This page intentionally left blank INDEX AIR FORCE PARTICIPATION I N PROJECT RULISON FINAL REPORT PARAGRAPH BASIC REPORT SUBJECT R e f e r e n c e s PAGE 2 G e n e r a l 1 3 P l a n n i n g 3 4 Command

  1. [Environmental investigation of ground water contamination at Wright-Patterson Air Force Base, Ohio]. Volume 2, Work plan: Phase 1, Task 4, Field Investigation: Draft

    SciTech Connect (OSTI)

    Not Available

    1991-10-01

    In April 1990 Wright-Patterson Air Force Base (WPAFB) initiated an investigation to evaluate a potential CERCLA removal action to prevent, to the extent practicable, the migration of ground-water contamination in the Mad River Valley Aquifer within and across WPAFB boundaries. The action will be based on a Focused Feasibility Study with an Action Memorandum serving as a decision document that is subject to approval by the Ohio Environmental Protection Agency. The first phase (Phase 1) of this effort involves an investigation of ground-water contamination migrating across the southwest boundary of Area C and across Springfield Pike adjacent to Area B. Task 4 of Phase 1 is a field investigation to collect sufficient additional information to evaluate removal alternatives. The field investigation will provide information in the following specific areas of study: water-level data which will be used to permit calibration of the ground-water flow model to a unique time in history; and ground-water quality data which will be used to characterize the current chemical conditions of ground water.

  2. Clean Air Task Force CATF | Open Energy Information

    Open Energy Info (EERE)

    Force (CATF) Place: Boston, Massachusetts Zip: 2108 Product: Massachusetts-based scientific research and legal advocacy center. References: Clean Air Task Force (CATF)1 This...

  3. ImagineSolar | Open Energy Information

    Open Energy Info (EERE)

    Workforce training, Corporate consulting - Solar projects, Solar sales, Solar marketing, Solar business development, Solar policy, Solar advocacy, Solar government...

  4. Solar Manufacturing Projects | Department of Energy

    Energy Savers [EERE]

    Solar Manufacturing Projects Solar Manufacturing Projects Solar Manufacturing Projects Solar Manufacturing Projects Solar Manufacturing Projects Solar Manufacturing Projects SOLAR ...

  5. Investigation of the Effect of I-ZnO Window Layer on the Device Performance of the Cd-Free CIGS Based Solar Cells: Preprint

    SciTech Connect (OSTI)

    Hasoon, F. S.; Al-Thani, H. A.; Li, X.; Kanevce, A.; Perkins, C.; Asher, S.

    2008-05-01

    This paper focuses on preparing Cd-free, CIGS-based solar cells with intrinsic high resistivity ZnO (I-ZnO) films deposited by metal-organic chemical vapor deposition (MOCVD) technique at different deposition substrate temperature and I-ZnO film thickness, and the effect of the prior treatment of CIGS films by ammonium hydroxide (NH4OH) diluted solution on the device performance.

  6. Microstructure of amorphous-silicon-based solar cell materials by small-angle x-ray scattering. Annual subcontract report, 6 April 1994--5 April 1995

    SciTech Connect (OSTI)

    Williamson, D.L.

    1995-08-01

    The general objective of this research is to provide detailed microstructural information on the amorphous-silicon-based, thin-film materials under development for improved multijunction solar cells. The experimental technique used is small-angle x-ray scattering (SAXS) providing microstructural data on microvoid fractions, sizes, shapes, and their preferred orientations. Other microstructural features such as alloy segregation, hydrogen-rich clusters and alloy short-range order are probed.

  7. Improved Solar Cell Efficiency Through the Use of an Additive Nanostructure-Based Optical Downshifter: Final Subcontract Report, January 28, 2010 -- February 28, 2011

    SciTech Connect (OSTI)

    Kurtin, J.

    2011-05-01

    This final report summarizes all SpectraWatt's progress in achieving a boost in solar cell efficiency using an optical downshifter. Spectrawatt's downshifting technology is based on a nanostructured material system which absorbs high energy (short wavelength) light and reemits it at a lower energy (long wavelength) with high efficiency. This system has shown unprecedented performance parameters including near unity quantum yield and high thermal stability.

  8. High Efficiency CdTe Ink-Based Solar Cells Using Nanocrystals (Fact Sheet), NREL Highlights in Science, NREL (National Renewable Energy Laboratory)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL researchers create a solution-processable "ink" to produce high-efficiency solar cells using low temperature and simple processing. Colloidal nanocrystals (NCs) provide a route toward simplified manufacturing of electronic devices compared to vacuum-based technology. Scientists from the National Renewable Energy Laboratory (NREL) collaborated with researchers at the University of Chicago on the colloidal synthesis of 5-10-nm crystals by using the solution as an ink to form large

  9. Solar Energies | Open Energy Information

    Open Energy Info (EERE)

    Energies Jump to: navigation, search Name: Solar Energies Place: France Product: France-based project company set up by Aerowatt, Credit Agricole Private Equity and the CDC to...

  10. Covalent Solar | Open Energy Information

    Open Energy Info (EERE)

    Massachusetts Product: Massachusetts-based developer of luminescent concentrator PV cells. References: Covalent Solar1 This article is a stub. You can help OpenEI by...

  11. Shared Solar Programs: Opportunities and Challenges

    Broader source: Energy.gov [DOE]

    The third webinar in the Solar Technical Assistance Team (STAT) 2013 webinar series, this webinar provides an overview of issues related to shared solar, the critical elements of a program to make it successful, and examples of locations that have implemented a shared solar or community-based solar program.

  12. Solar Rights

    Broader source: Energy.gov [DOE]

    In the context of this law, a solar energy device is a system "manufactured and sold for the sole purpose of facilitating the collection and beneficial use of solar energy, including passive...

  13. Solar Blog

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    96426 Solar Blog en Solar Energy Jobs Outpace U.S. Economy http:energy.govarticlessolar-energy-jobs-outpace-us-economy

  14. Solar Rights

    Broader source: Energy.gov [DOE]

    Cities and counties in North Carolina generally may not adopt ordinances prohibiting the installation of "a solar collector that gathers solar radiation as a substitute for traditional energy for...

  15. Solar Rights

    Broader source: Energy.gov [DOE]

    A solar energy system is defined as "a system affixed to a building or buildings that uses solar devices, which are thermally isolated from living space or any other area where the energy is used...

  16. Solar Forecasting

    Broader source: Energy.gov [DOE]

    On December 7, 2012, DOE announced $8 million to fund two solar projects that are helping utilities and grid operators better forecast when, where, and how much solar power will be produced at U.S....

  17. A new architecture as transparent electrodes for solar and IR applications based on photonic structures via soft lithography

    SciTech Connect (OSTI)

    Kuang, Ping

    2011-05-15

    Transparent conducting electrodes with the combination of high optical transmission and good electrical conductivity are essential for solar energy harvesting and electric lighting devices. Currently, indium tin oxide (ITO) is used because ITO offers relatively high transparency (>80%) to visible light and low sheet resistance (R{sub s} = 10 ohms/square ({Omega}#2;/?)) for electrical conduction. However, ITO is costly due to limited indium reserves, and it is brittle. These disadvantages have motivated the search for other conducting electrodes with similar or better properties. There has been research on a variety of electrode structures involving carbon nanotube networks, graphene films, nanowire and nanopatterned meshes and grids. Due to their novel characteristics in light manipulation and collection, photonic crystal structures show promise for further improvement. Here, we report on a new architecture consisting of nanoscale high aspect ratio metallic photonic structures as transparent electrodes fabricated via a combination of processes. For (Au) and silver (Ag) structures, the visible light transmission can reach as high as 80%, and the sheet resistance of the structure can be as low as 3.2{Omega}#2;/?. The optical transparency of the high aspect ratio metal structures at visible wavelength range is comparable to that of ITO glass, while their sheet resistance is more than 3 times lower, which indicates a much higher electrical conductivity of the metal structures. Furthermore, the high aspect ratio metal structures have very high infrared (IR) reflection (90%) for the transverse magnetic (TM) mode, which can lead to the development of fabrication of metallic structures as IR filters for heat control applications. Investigations of interdigitated structures based on the high aspect ratio metal electrodes are ongoing to study the feasibility in smart window applications in light transmission modulation.

  18. Remnant PbI{sub 2}, an unforeseen necessity in high-efficiency hybrid perovskite-based solar cells?

    SciTech Connect (OSTI)

    Cao, Duyen H.; Stoumpos, Constantinos C.; Malliakas, Christos D.; Katz, Michael J.; Hupp, Joseph T. E-mail: m-kanatzidis@northwestern.edu; Kanatzidis, Mercouri G. E-mail: m-kanatzidis@northwestern.edu; Farha, Omar K.

    2014-09-01

    Perovskite-containing solar cells were fabricated in a two-step procedure in which PbI{sub 2} is deposited via spin-coating and subsequently converted to the CH{sub 3}NH{sub 3}PbI{sub 3} perovskite by dipping in a solution of CH{sub 3}NH{sub 3}I. By varying the dipping time from 5 s to 2 h, we observe that the device performance shows an unexpectedly remarkable trend. At dipping times below 15 min the current density and voltage of the device are enhanced from 10.1 mA/cm{sup 2} and 933 mV (5 s) to 15.1 mA/cm{sup 2} and 1036 mV (15 min). However, upon further conversion, the current density decreases to 9.7 mA/cm{sup 2} and 846 mV after 2 h. Based on X-ray diffraction data, we determined that remnant PbI{sub 2} is always present in these devices. Work function and dark current measurements showed that the remnant PbI{sub 2} has a beneficial effect and acts as a blocking layer between the TiO{sub 2} semiconductor and the perovskite itself reducing the probability of back electron transfer (charge recombination). Furthermore, we find that increased dipping time leads to an increase in the size of perovskite crystals at the perovskite-hole-transporting material interface. Overall, approximately 15 min dipping time (?2% unconverted PbI{sub 2}) is necessary for achieving optimal device efficiency.

  19. The Genesis Mission: Solar Wind Conditions, and Implications for the FIP Fractionation of the Solar Wind.

    SciTech Connect (OSTI)

    Reisenfeld, D. B.; Wiens, R. C.; Barraclough, B. L.; Steinberg, J. T; Dekoning, C. A.; Zurbuchen, T. H.; Burnett, D. S.

    2005-01-01

    The NASA Genesis mission collected solar wind on ultrapure materials between November 30, 2001 and April 1, 2004. The samples were returned to Earth September 8, 2004. Despite the hard landing that resulted from a failure of the avionics to deploy the parachute, many samples were returned in a condition that will permit analyses. Sample analyses of these samples should give a far better understanding of the solar elemental and isotopic composition (Burnett et al. 2003). Further, the photospheric composition is thought to be representative of the solar nebula, so that the Genesis mission will provide a new baseline for the average solar nebula composition with which to compare present-day compositions of planets, meteorites, and asteroids. Sample analysis is currently underway. The Genesis samples must be placed in the context of the solar and solar wind conditions under which they were collected. Solar wind is fractionated from the photosphere by the forces that accelerate the ions off of the Sun. This fractionation appears to be ordered by the first ionization potential (FIP) of the elements, with the tendency for low-FIP elements to be over-abundant in the solar wind relative to the photosphere, and high-FIP elements to be under-abundant (e.g. Geiss, 1982; von Steiger et al., 2000). In addition, the extent of elemental fractionation differs across different solarwind regimes. Therefore, Genesis collected solar wind samples sorted into three regimes: 'fast wind' or 'coronal hole' (CH), 'slow wind' or 'interstream' (IS), and 'coronal mass ejection' (CME). To carry this out, plasma ion and electron spectrometers (Barraclough et al., 2003) continuously monitored the solar wind proton density, velocity, temperature, the alpha/proton ratio, and angular distribution of suprathermal electrons, and those parameters were in turn used in a rule-based algorithm that assigned the most probable solar wind regime (Neugebauer et al., 2003). At any given time, only one of three regime-specific collectors (CH, IS, or CME) was exposed to the solar wind. Here we report on the regime-specific solar wind conditions from in-situ instruments over the course of the collection period. Further, we use composition data from the SWICS (Solar Wind Ion Composition Spectrometer) instrument on ACE (McComas et al., 1998) to examine the FIP fractionation between solar wind regimes, and make a preliminary comparison of these to the FIP analysis of Ulysses/SWICS composition data (von Steiger et al. 2000). Our elemental fractionation study includes a reevaluation of the Ulysses FIP analysis in light of newly reported photospheric abundance data (Asplund, Grevesse & Sauval, 2005). The new abundance data indicate a metallicity (Z/X) for the Sun almost a factor of two lower than that reported in the widely used compilation of Anders & Grevesse (1989). The new photospheric abundances suggest a lower degree of solar wind fractionation than previously reported by von Steiger et al. (2000) for the first Ulysses polar orbit (1991-1998).

  20. Solar collectors

    SciTech Connect (OSTI)

    Cassidy, V.M.

    1981-11-01

    Practical applications of solar energy in commercial, industrial and institutional buildings are considered. Two main types of solar collectors are described: flat plate collectors and concentrating collectors. Efficiency of air and hydronic collectors among the flat plate types are compared. Also several concentrators are described, including their sun tracking mechanisms. Descriptions of some recent solar installations are presented and a list representing the cross section of solar collector manufacturers is furnished.

  1. Solar Easements

    Broader source: Energy.gov [DOE]

    In addition, the state’s local zoning ordinances must address access to air and light, views, and solar access.

  2. Solar Newsletter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Facilities Battery Abuse Testing Laboratory Cylindrical Boiling Facility Distributed Energy Technology Lab Microsystems and Engineering Sciences Applications National Solar ...

  3. Solar Newsletter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    National Solar Thermal Test Facility Nuclear ... Climate & Earth Systems Climate Measurement & Modeling ... Tribal Energy Program Intellectual Property Current EC ...

  4. Pokeberries Provide Boost for Solar Cells

    Broader source: Energy.gov [DOE]

    Red dye from the pokeberry weed makes their low-cost, fiber-based solar cells even more energy efficient.

  5. [Environmental investigation of ground water contamination at Wright-Patterson Air Force Base, Ohio]. Volume 3, Sampling and analysis plan (SAP): Phase 1, Task 4, Field Investigation: Draft

    SciTech Connect (OSTI)

    Not Available

    1991-10-01

    In April 1990, Wright-Patterson Air Force Base (WPAFB), initiated an investigation to evaluate a potential Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) removal action to prevent, to the extent practicable, the offsite migration of contaminated ground water from WPAFB. WPAFB retained the services of the Environmental Management Operations (EMO) and its principle subcontractor, International Technology Corporation (IT) to complete Phase 1 of the environmental investigation of ground-water contamination at WPAFB. Phase 1 of the investigation involves the short-term evaluation and potential design for a program to remove ground-water contamination that appears to be migrating across the western boundary of Area C, and across the northern boundary of Area B along Springfield Pike. Primarily, Task 4 of Phase 1 focuses on collection of information at the Area C and Springfield Pike boundaries of WPAFB. This Sampling and Analysis Plan (SAP) has been prepared to assist in completion of the Task 4 field investigation and is comprised of the Quality Assurance Project Plan (QAPP) and the Field Sampling Plan (FSP).

  6. Novel attributes in modeling and optimizing of the new graphene based In{sub x}Ga{sub 1?x}N Schottky barrier solar cells

    SciTech Connect (OSTI)

    Arefinia, Zahra [Research Institute for Applied Physics and Astronomy, University of Tabriz, Tabriz 51666-14766 (Iran, Islamic Republic of); Asgari, Asghar, E-mail: asgari@tabrizu.ac.ir [Research Institute for Applied Physics and Astronomy, University of Tabriz, Tabriz 51666-14766 (Iran, Islamic Republic of); School of Electrical, Electronic, and Computer Engineering, University of Western Australia, Crawley, WA 6009 (Australia)

    2014-05-21

    Based on the ability of In{sub x}Ga{sub 1?x}N materials to optimally span the solar spectrum and their superior radiation resistance, solar cells based on p-type In{sub x}Ga{sub 1?x}N with low indium contents and interfacing with graphene film (G/In{sub x}Ga{sub 1?x}N), is proposed to exploit the benefit of transparency and work function tunability of graphene. Then, their solar power conversion efficiency modeled and optimized using a new analytical approach taking into account all recombination processes and accurate carrier mobility. Furthermore, their performance was compared with graphene on silicon counterparts and G/p-In{sub x}Ga{sub 1?x}N showed relatively smaller short-circuits current (?7?mA/cm{sup 2}) and significantly higher open-circuit voltage (?4?V) and efficiency (?30%). The thickness, doping concentration, and indium contents of p-In{sub x}Ga{sub 1?x}N and graphene work function were found to substantially affect the performance of G/p-In{sub x}Ga{sub 1?x}N.

  7. Physics-Based Compact Model for CIGS and CdTe Solar Cells: From Voltage-Dependent Carrier Collection to Light-Enhanced Reverse Breakdown: Preprint

    SciTech Connect (OSTI)

    Sun, Xingshu; Alam, Muhammad Ashraful; Raguse, John; Garris, Rebekah; Deline, Chris; Silverman, Timothy

    2015-10-15

    In this paper, we develop a physics-based compact model for copper indium gallium diselenide (CIGS) and cadmium telluride (CdTe) heterojunction solar cells that attributes the failure of superposition to voltage-dependent carrier collection in the absorber layer, and interprets light-enhanced reverse breakdown as a consequence of tunneling-assisted Poole-Frenkel conduction. The temperature dependence of the model is validated against both simulation and experimental data for the entire range of bias conditions. The model can be used to characterize device parameters, optimize new designs, and most importantly, predict performance and reliability of solar panels including the effects of self-heating and reverse breakdown due to partial-shading degradation.

  8. Optimization of Phase-Engineered a-Si:H-Based Multi-Junction Solar Cells: Final Technical Report, October 2001-July 2005

    SciTech Connect (OSTI)

    Wronski, C. R.; Collins, R. W.; Podraza, N. J.; Vlahos, V.; Pearce, J. M.; Deng, J.; Albert, M.; Ferreira, G. M.; Chen, C.

    2006-08-01

    The scope of the work under this subcontract has involved investigating engineered improvements in the performance and stability of solar cells in a systematic way, which included the following four tasks: (1) Materials research and device development; (2) Process improvement directed by real time diagnostics; (3) Device loss mechanisms; and (4) Characterization strategies for advanced materials Our work has resulted in new and important insights into the deposition of a-Si:H-based materials, as well as into the nature of the Staebler-Wronski Effect (SWE). Presumably, many of these insights will be used by industrial partners to develop more systematic approaches in optimizing solar cells for higher performance and stability. This effort also cleared up several serious misconceptions about the nature of the p-layer in cells and the SWE in materials and cells. Finally, the subcontract identified future directions that should be pursued for greater understanding and improvement.

  9. Amorphous semiconductor solar cell

    DOE Patents [OSTI]

    Dalal, Vikram L. (Newark, DE)

    1981-01-01

    A solar cell comprising a back electrical contact, amorphous silicon semiconductor base and junction layers and a top electrical contact includes in its manufacture the step of heat treating the physical junction between the base layer and junction layer to diffuse the dopant species at the physical junction into the base layer.

  10. Microsoft Word - Energy Code Enforcement Funding Task Force - Fact Sheet

    Energy Savers [EERE]

    [Final].docx | Department of Energy Energy Code Enforcement Funding Task Force - Fact Sheet [Final].docx Microsoft Word - Energy Code Enforcement Funding Task Force - Fact Sheet [Final].docx PDF icon Microsoft Word - Energy Code Enforcement Funding Task Force - Fact Sheet [Final].docx More Documents & Publications Sonoma County Solar Implementation Plan Webinar: Residential Energy Code Compliance QER - Comment of IEEE

  11. Colexon Solar Invest AS Formerly Renewagy AS | Open Energy Information

    Open Energy Info (EERE)

    Product: Denmark-based development and investment company that focuses on wind and solar PV project development. References: Colexon Solar Invest AS (Formerly Renewagy AS)1...

  12. Xunlight Corp previously MWOE Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    Xunlight Corp previously MWOE Solar Inc Jump to: navigation, search Name: Xunlight Corp (previously MWOE Solar Inc) Place: Toledo, Ohio Zip: 43607 Product: US-based developer of...

  13. Kinmac Solar formerly Lucky Power Technology Co Ltd | Open Energy...

    Open Energy Info (EERE)

    Taiwan Sector: Solar Product: Taiwan-based manufacturer of solar modules, chargers, inverters, batteries and related products. Coordinates: 24.69389, 121.148064 Show Map...

  14. New Mexico: Solar Glare Hazard Analysis Tool Maximizes Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Laboratories developed the Solar Glare Hazard Analysis Tool (SGHAT), a free Web-based tool that can quickly calculate potential visual hazards from proposed solar installations. ...

  15. Inner Mongolia Riyue Solar Technology Ltd | Open Energy Information

    Open Energy Info (EERE)

    Ltd Place: Inner Mongolia Autonomous Region, China Sector: Solar Product: China-based solar cell and module manufacturer in Inner Mongolia. References: Inner Mongolia Riyue...

  16. Dongguan Quoncion Solar Energy Lighting Co Ltd | Open Energy...

    Open Energy Info (EERE)

    Quoncion Solar Energy Lighting Co Ltd Jump to: navigation, search Name: Dongguan Quoncion Solar Energy Lighting Co.,Ltd. Place: Taiwan Product: Taiwan-based PV module manufacturer...

  17. Green Tech Solar Inc GTS | Open Energy Information

    Open Energy Info (EERE)

    British Columbia-based firm involved in the development of utility-scale solar and bio energy projects in the southwestern United States. References: Green Tech Solar Inc...

  18. SolarOne Solutions Inc | Open Energy Information

    Open Energy Info (EERE)

    Sector: Solar Product: Massachusetts-based manufacturer and retailer of solar powered LED lighting systems. Coordinates: 42.28107, -71.236054 Show Map Loading map......

  19. EffiSolar Energy Corporation | Open Energy Information

    Open Energy Info (EERE)

    search Name: EffiSolar Energy Corporation Place: Coquitlam, British Columbia, Canada Zip: V3K6V2 Sector: Solar Product: Canadian based project developer focused on...

  20. El Dorado Solar Project Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Solar Project Solar Power Plant Jump to: navigation, search Name El Dorado Solar Project Solar Power Plant Facility El Dorado Solar Project Sector Solar Facility Type Photovoltaic...

  1. Beacon Solar Energy Project Solar Power Plant | Open Energy Informatio...

    Open Energy Info (EERE)

    Solar Energy Project Solar Power Plant Jump to: navigation, search Name Beacon Solar Energy Project Solar Power Plant Facility Beacon Solar Energy Project Sector Solar Facility...

  2. Deming Solar Plant Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Deming Solar Plant Solar Power Plant Jump to: navigation, search Name Deming Solar Plant Solar Power Plant Facility Deming Solar Plant Sector Solar Facility Type Photovoltaic...

  3. SES Calico Solar One Project Solar Power Plant | Open Energy...

    Open Energy Info (EERE)

    Calico Solar One Project Solar Power Plant Jump to: navigation, search Name SES Calico Solar One Project Solar Power Plant Facility SES Calico Solar One Project Sector Solar...

  4. Nvision.Solar - Ravnishte Solar PV Plant | Open Energy Information

    Open Energy Info (EERE)

    Solar - Ravnishte Solar PV Plant Jump to: navigation, search Name Nvision.Solar - Ravnishte Solar PV Plant Facility Ravishte roof and facade mounted solar power plant Sector Solar...

  5. Solar Millenium Palen Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Palen Solar Power Plant Jump to: navigation, search Name Solar Millenium Palen Solar Power Plant Facility Solar Millenium Palen Sector Solar Facility Type Concentrating Solar Power...

  6. SES Solar Two Project Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Two Project Solar Power Plant Jump to: navigation, search Name SES Solar Two Project Solar Power Plant Facility SES Solar Two Project Sector Solar Facility Type Concentrating Solar...

  7. Prescott Airport Solar Plant Solar Power Plant | Open Energy...

    Open Energy Info (EERE)

    Prescott Airport Solar Plant Solar Power Plant Jump to: navigation, search Name Prescott Airport Solar Plant Solar Power Plant Facility Prescott Airport Solar Plant Sector Solar...

  8. Carrizo Energy Solar Farm Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Carrizo Energy Solar Farm Solar Power Plant Jump to: navigation, search Name Carrizo Energy Solar Farm Solar Power Plant Facility Carrizo Energy Solar Farm Sector Solar Facility...

  9. Proposed solar two project Barstow, California

    SciTech Connect (OSTI)

    Not Available

    1994-01-01

    This Environmental Assessment (EA) evaluates the environmental consequences of the proposed conversion and operation of the existing Solar One Facility in Daggett, Ca, near the city of Barstow, to a nitrate salt based heat transfer system, Solar Two. The EA also addresses the alternatives of different solar conversion technologies and alternative sites and discusses a no action alternative. A primary objective of the Solar Two Project is to demonstrate the technical and economic feasibility of a solar central receiver power plant using molten salt as the thermal storage and transport fluid medium. If successful, the information gathered from the Solar Two Project could be used to design larger commercial solar power plants.

  10. High-Efficiency Amorphous Silicon Alloy Based Solar Cells and Modules; Final Technical Progress Report, 30 May 2002--31 May 2005

    SciTech Connect (OSTI)

    Guha, S.; Yang, J.

    2005-10-01

    The principal objective of this R&D program is to expand, enhance, and accelerate knowledge and capabilities for development of high-efficiency hydrogenated amorphous silicon (a-Si:H) and amorphous silicon-germanium alloy (a-SiGe:H) related thin-film multijunction solar cells and modules with low manufacturing cost and high reliability. Our strategy has been to use the spectrum-splitting triple-junction structure, a-Si:H/a-SiGe:H/a-SiGe:H, to improve solar cell and module efficiency, stability, and throughput of production. The methodology used to achieve the objectives included: (1) explore the highest stable efficiency using the triple-junction structure deposited using RF glow discharge at a low rate, (2) fabricate the devices at a high deposition rate for high throughput and low cost, and (3) develop an optimized recipe using the R&D batch large-area reactor to help the design and optimization of the roll-to-roll production machines. For short-term goals, we have worked on the improvement of a-Si:H and a-SiGe:H alloy solar cells. a-Si:H and a-SiGe:H are the foundation of current a-Si:H based thin-film photovoltaic technology. Any improvement in cell efficiency, throughput, and cost reduction will immediately improve operation efficiency of our manufacturing plant, allowing us to further expand our production capacity.

  11. Solarmarkt Solar Sued Park GmbH | Open Energy Information

    Open Energy Info (EERE)

    Solarmarkt Solar Sued Park GmbH Jump to: navigation, search Name: Solarmarkt Solar Sued Park GmbH Place: Memmingen, Bavaria, Germany Zip: 87700 Sector: Solar Product: Bavaria-based...

  12. ZebaSolar India Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    ZebaSolar India Pvt Ltd Jump to: navigation, search Name: ZebaSolar India Pvt. Ltd. Place: Raipur, Chhattisgarh, India Zip: 492001 Sector: Solar Product: Raipur-based firm setting...

  13. Solar Green Technology S p A SGT | Open Energy Information

    Open Energy Info (EERE)

    Green Technology S p A SGT Jump to: navigation, search Name: Solar Green Technology S.p.A. (SGT) Place: Italy Sector: Solar Product: Italy-based solar system integrator....

  14. SchwabenSolar GmbH | Open Energy Information

    Open Energy Info (EERE)

    Germany Zip: 86399 Sector: Solar Product: Bavaria-based manufacturer of solar inverters and PV junction boxes. References: SchwabenSolar GmbH1 This article is a stub. You...

  15. Solar Energy Trading GmbH SET | Open Energy Information

    Open Energy Info (EERE)

    GmbH SET Jump to: navigation, search Name: Solar Energy Trading GmbH (SET) Place: Mnster, Germany Zip: 48157 Sector: Solar Product: Germany-based solar project developer and...

  16. BlueSol Solar Energy | Open Energy Information

    Open Energy Info (EERE)

    BlueSol Solar Energy Jump to: navigation, search Name: BlueSol - Solar Energy Place: Sao Paulo, Sao Paulo, Brazil Zip: 04551-060 Sector: Solar Product: Sao Paulo-based sole...

  17. LQ Energy LDK Solar Q Cells JV | Open Energy Information

    Open Energy Info (EERE)

    LQ Energy LDK Solar Q Cells JV Jump to: navigation, search Name: LQ Energy (LDK Solar & Q-Cells JV) Place: Saxony-Anhalt, Germany Sector: Solar Product: Germany-based JV between...

  18. Applied Solar Technologies Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    Ltd. Place: Delhi (NCT), India Sector: Solar Product: Delhi-based firm that provides off-grid solar power to telecom towers. It builds and operates solar installations and takes...

  19. Taean Solar Farm Co Ltd | Open Energy Information

    Open Energy Info (EERE)

    Taean Solar Farm Co Ltd Jump to: navigation, search Name: Taean Solar Farm Co.,Ltd Place: South Chungcheong, Korea (Republic) Sector: Solar Product: Korea-based project developer,...

  20. Measuring solar reflectance Part I: Defining a metric that accurately...

    Office of Scientific and Technical Information (OSTI)

    A widely used solar reflectance metric based on the ASTM Standard E891 beam-normal solar spectral irradiance underestimates the solar heat gain of a spectrally selective 'cool ...

  1. Radiation control coatings installed on federal buildings at Tyndall Air Force Base. Volume 1: Pre-coating monitoring and fresh coating results

    SciTech Connect (OSTI)

    Petrie, T.W.; Childs, P.W.

    1997-02-01

    The US Department of Energy`s (DOE`s) Federal Energy Management Program (FEMP) supports efforts to reduce energy use and associated expenses in the federal sector. One such effort, the New Technology Demonstration Program (NTDP), seeks to evaluate new energy-saving US technologies and secure their more timely adoption by the US government. Through a partnership with a federal site, the utility serving the site, a manufacturer of an energy-related technology, and other organizations associated with these interests, DOE can evaluate a new technology. The results of the program give federal agency decision makers more hands-on information with which to validate a decision to utilize a new technology in their facilities. The partnership of these interests is secured through a cooperative research and development agreement (CRADA), in this case between Lockheed Martin Energy Research Corporation, the manager of the Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee, and ThermShield International, Ltd., the manufacturer of the technology. This is the first volume of a two-volume report that describes the effects of radiation control coatings installed on federal buildings at Tyndall Air Force Base (AFB) in Florida by ThermShield International. ORNL`s Buildings Technology Center (BTC) was assigned the responsibility for gathering, analyzing, and reporting on the data to describe the effects of the coatings. This volume describes the monitoring plan and its implementation, the results of pre-coating monitoring, the coating installation, results from fresh coatings compared to pre-coating results, and a plan to decommission the monitoring equipment. By including results from roofs at Tyndall AFB and from an outdoor test facility at the BTC, the data cover the range from poorly insulated to well-insulated roofs and two kinds of radiation control coatings on various roof membranes.

  2. NREL: Concentrating Solar Power Research - Concentrating Solar...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Concentrating Solar Power Resource Maps These direct-normal solar radiation maps-filtered by solar resource and land availability-identify the most economically suitable lands ...

  3. Solar Newsletter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas ...

  4. Solar Rights

    Broader source: Energy.gov [DOE]

    Ordinances, bylaws, or regulations may reasonably restrict the installation and use of solar energy devices to protect public health and safety, buildings from damage, historic/aesthetic values (...

  5. Solar Mapper

    Broader source: Energy.gov [DOE]

    Interactive, online mapping tool providing access to spatial data related to siting utility-scale solar facilities in the southwestern United States.

  6. 100 mm Engineered InP-on-Si Laminate Substrates for InP-based Multijunction Solar Cells

    SciTech Connect (OSTI)

    Atwater, Harry

    2012-06-25

    The project focused on fabrication of InP/Si laminate substrates as templates for growth of InGaAsP/InGaAs and InAlAs/InGaAsP/InGaAs multijunction solar cells. InP/Si template substrates were developed and used as templates for InGaAs solar growth. A novel feature of the program was development of the virtual substrate template, which enables a substrate to be formed with a lattice constant intermediate between those of GaAs and InP. Large-area virtual substrate templates were formed by transfer and bonding of dislocation free InGaAs films wafer onto silicon substrates.

  7. Micromechanism linear actuator with capillary force sealing

    DOE Patents [OSTI]

    Sniegowski, Jeffry J.

    1997-01-01

    A class of micromachine linear actuators whose function is based on gas driven pistons in which capillary forces are used to seal the gas behind the piston. The capillary forces also increase the amount of force transmitted from the gas pressure to the piston. In a major subclass of such devices, the gas bubble is produced by thermal vaporization of a working fluid. Because of their dependence on capillary forces for sealing, such devices are only practical on the sub-mm size scale, but in that regime they produce very large force times distance (total work) values.

  8. Evidence of significant down-conversion in a Si-based solar cell using CuInS{sub 2}/ZnS core shell quantum dots

    SciTech Connect (OSTI)

    Gardelis, Spiros Nassiopoulou, Androula G.

    2014-05-05

    We report on the increase of up to 37.5% in conversion efficiency of a Si-based solar cell after deposition of light-emitting Cd-free, CuInS{sub 2}/ZnS core shell quantum dots on the active area of the cell due to the combined effect of down-conversion and the anti- reflecting property of the dots. We clearly distinguished the effect of down-conversion from anti-reflection and estimated an enhancement of up to 10.5% in the conversion efficiency due to down-conversion.

  9. Development of Advanced CdTe Solar Cells Based on High Temperature Corning Glass Substrates: Cooperative Research and Development Final Report, CRADA Number CRD-10-373

    SciTech Connect (OSTI)

    Barnes, T.

    2013-08-01

    NREL has developed advanced processes for CdTe solar cells, but because of the temperature limitations of conventional soda lime glass, many of these processes have not been transferred to manufacturing. Corning is developing high temperature substrate glasses that are believed to be manufacturable and will lead to lower $/watt modules costs. The purpose of this CRADA is to evaluate these glasses in the advanced NREL processes. In addition, the CRADA seeks to develop manufacturable processes for transparent conductive oxide layers based on cadmium stannate.

  10. Sunner Solar Corp | Open Energy Information

    Open Energy Info (EERE)

    Name: Sunner Solar Corp. Place: Taoyuan, Taiwan Product: A Taiwan-based thin-film PV cell manufacturer References: Sunner Solar Corp.1 This article is a stub. You can help...

  11. E TON Solar Tech | Open Energy Information

    Open Energy Info (EERE)

    Solar Tech Jump to: navigation, search Name: E-TON Solar Tech Place: Tainan, Taiwan Zip: 709 Product: Taiwan-based manufacturer of PV cells. Coordinates: 22.99721, 120.180862...

  12. Utility Scale Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    Scale Solar Inc Place: Palo Alto, California Zip: 94301 Product: California-based PV tracker maker. References: Utility Scale Solar Inc1 This article is a stub. You can help...

  13. BioSolar Inc | Open Energy Information

    Open Energy Info (EERE)

    BioSolar Inc Jump to: navigation, search Name: BioSolar Inc Place: Santa Clara, California Zip: 91387 Product: US-based manufacturer of sub and superstrates made of plant sources;...

  14. HyperSolar Inc | Open Energy Information

    Open Energy Info (EERE)

    HyperSolar Inc Jump to: navigation, search Name: HyperSolar Inc Place: Santa Barbara, California Zip: 93117 Product: California-based concentrator PV startup which uses flat...

  15. City of Boulder- Solar Grant Program

    Broader source: Energy.gov [DOE]

    The Solar Grant Program provides grants for PV and solar water heating installations on housing enrolled in the city's affordable housing program, site-based non-profit organizations, and low- to...

  16. Payom Solar AG | Open Energy Information

    Open Energy Info (EERE)

    Payom Solar AG Jump to: navigation, search Name: Payom Solar AG Place: Merkendorf, Germany Zip: 91732 Product: Germany-based installer of roof-mounted PV plants, which also trades...

  17. T Solar Global SA | Open Energy Information

    Open Energy Info (EERE)

    Solar Global SA Jump to: navigation, search Name: T-Solar Global SA Place: Madrid, Spain Zip: 28042 Product: Spain-based thin-film silicon PV cell and module maker, using Applied...

  18. First Philec Solar Corp | Open Energy Information

    Open Energy Info (EERE)

    Place: Binan, Laguna, Philippines Zip: 4024 Sector: Services, Solar Product: First Philec Solar Corporation is a JV between US-based PV cell and module maker SunPower and First...

  19. Solar Power Inc SPI | Open Energy Information

    Open Energy Info (EERE)

    Solar Power Inc SPI Jump to: navigation, search Name: Solar Power Inc (SPI) Place: Roseville, California Zip: 95661 Product: US-based manufacturer of PV modules with a factory in...

  20. Solar Wind Europe SL | Open Energy Information

    Open Energy Info (EERE)

    Europe SL Jump to: navigation, search Name: Solar Wind Europe SL Place: Madrid, Spain Zip: 28028 Product: Spain-based distributor of Russia-made PV modules. References: Solar Wind...

  1. Solar Energy Partners | Open Energy Information

    Open Energy Info (EERE)

    Zip: W1K 4ND Sector: Solar Product: London-based firm active in investments in photovoltaic and thermal solar energy projects for pension funds, private equity, specialist...

  2. Canadian Solar Inc CSI | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search Name: Canadian Solar Inc (CSI) Place: Kitchener, Ontario, Canada Zip: N2K 3S2 Sector: Solar Product: Canada-incorporated, China-based manufacturer of...

  3. EPOD Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    Inc Jump to: navigation, search Name: EPOD Solar Inc Place: Kelowna, British Columbia, Canada Zip: V1V 2L9 Sector: Solar Product: British Columbia-based thin-film a-Si PV maker as...

  4. Northgrid Solar Inc | Open Energy Information

    Open Energy Info (EERE)

    Inc Jump to: navigation, search Name: Northgrid Solar Inc. Place: Markham, Ontario, Canada Zip: L6E 1A9 Sector: Services, Solar Product: String representation "Ontario-based N...

  5. Micro-inverter solar panel mounting

    DOE Patents [OSTI]

    Morris, John; Gilchrist, Phillip Charles

    2016-02-02

    Processes, systems, devices, and articles of manufacture are provided. Each may include adapting micro-inverters initially configured for frame-mounting to mounting on a frameless solar panel. This securement may include using an adaptive clamp or several adaptive clamps secured to a micro-inverter or its components, and using compressive forces applied directly to the solar panel to secure the adaptive clamp and the components to the solar panel. The clamps can also include compressive spacers and safeties for managing the compressive forces exerted on the solar panels. Friction zones may also be used for managing slipping between the clamp and the solar panel during or after installation. Adjustments to the clamps may be carried out through various means and by changing the physical size of the clamps themselves.

  6. Photovoltaic Solar Projects | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Photovoltaic Solar Projects Photovoltaic Solar Projects Photovoltaic Solar Projects Photovoltaic Solar Projects Photovoltaic Solar Projects Photovoltaic Solar Projects Photovoltaic ...

  7. Protective Force Program Manual

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2000-06-30

    Provides detailed requirements to supplement DOE O 473.2, Protective Force Program, which establishes the requirements and responsibilities for management and operation of the Department of Energy (DOE) Protective Force (PF) Program. Does not cancel other directives.

  8. Solar IT | Open Energy Information

    Open Energy Info (EERE)

    IT Jump to: navigation, search Name: Solar IT Place: Ramat-Gan, Israel Product: Ramat-Gan-based supplier and assemblier of PV-based systems for domestic and industrial use....

  9. Solar Radiometric Data Quality Assessment of SIRS, SKYRAD and GNDRAD

    Office of Scientific and Technical Information (OSTI)

    Measurements (Poster) (Conference) | SciTech Connect Conference: Solar Radiometric Data Quality Assessment of SIRS, SKYRAD and GNDRAD Measurements (Poster) Citation Details In-Document Search Title: Solar Radiometric Data Quality Assessment of SIRS, SKYRAD and GNDRAD Measurements (Poster) Solar radiation is the driving force for the earth's weather and climate. Understanding the elements of this dynamic energy balance requires accurate measurements of broadband solar irradiance. Since the

  10. Fluid force transducer

    DOE Patents [OSTI]

    Jendrzejczyk, Joseph A.

    1982-01-01

    An electrical fluid force transducer for measuring the magnitude and direction of fluid forces caused by lateral fluid flow, includes a movable sleeve which is deflectable in response to the movement of fluid, and a rod fixed to the sleeve to translate forces applied to the sleeve to strain gauges attached to the rod, the strain gauges being connected in a bridge circuit arrangement enabling generation of a signal output indicative of the magnitude and direction of the force applied to the sleeve.

  11. Administering Work Force Discipline

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2015-05-14

    The order provides requirements and responsibilities for administering work force discipline and corrective actions. Supersedes DOE O 3750.1.

  12. Unified Solar

    Broader source: Energy.gov [DOE]

    Unified Solar is an MIT startup that is commercializing an integrated circuit solution that eliminates most of the adverse effects caused by partial shading in photovoltaic power systems. With its patent-pending design, Unified Solar's solution is smaller, cheaper and more powerful than any competing power optimizer in the market.

  13. Sandia Energy - Solar Resource Assessment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solar Resource Assessment Home Stationary Power Energy Conversion Efficiency Solar Energy Photovoltaics Solar Resource Assessment Solar Resource AssessmentTara...

  14. Sandia Energy - Solar Market Transformation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solar Market Transformation Home Stationary Power Energy Conversion Efficiency Solar Energy Photovoltaics Solar Market Transformation Solar Market TransformationTara...

  15. Marin Solar Village: feasibility study and technical analysis. Final report

    SciTech Connect (OSTI)

    Not Available

    1980-08-31

    The energy needs of Hamilton Air Force Base's Solar Village for electricity and heating and cooling of buildings are considered and alternative ways of meeting the Village's requirements for these forms of energy are evaluated. First, Solar Village's energy demand is calculated and compared to a base case representing calculations for typical energy usage for a development of similar size and density that is in conformance with current state and local ordinances. The potential of selected alternative technologies to meet the Solar Village projected demand for electrical power and natural gas is evaluated. Scenarios were developed to reduce demand, particularly in the building sector. Four alternative on-site energy technologies have been evaluated: wind, solar thermal electric, biomass conversion, photovoltaics. Each alternative is analyzed in detail. Of the four alternatives considered, the one with the greatest present potential is biomass conversion. Two technologies have been incorporated into the design. A 3-acre land fill is covered with a mantle of soil. A network of pipes carries off the methane gas which is a natural product of anaerobic decomposition of the materials in the land fill. The second technology involves the planting of rapidly-growing trees on denuded and unused portions of the site; 50 acres devoted to tree production could yield 12% of the back-up energy required for home heating on a sustainable basis.

  16. Perovskite solar cells with near 100% internal quantum efficiency based on large single crystalline grains and vertical bulk heterojunctions

    SciTech Connect (OSTI)

    Yang, Bin; Dyck, Ondrej; Poplawsky, Jonathan; Keum, Jong; Puretzky, Alexander; Das, Sanjib; Ivanov, Ilia; Rouleau, Christopher; Duscher, Gerd; Geohegan, David; Xiao, Kai

    2015-07-09

    Grain boundaries (GBs) as defects in the crystal lattice detrimentally impact the power conversion efficiency (PCE) of polycrystalline solar cells, particularly in recently emerging hybrid perovskites where non-radiative recombination processes lead to significant carrier losses. Here, the beneficial effects of activated vertical GBs are demonstrated by first growing large, vertically-oriented methylammonium lead tri-iodide (CH3NH3PbI3) single-crystalline grains. We show that infiltration of p-type doped 2 -7,7 -tetrakis(N,Ndi-p-methoxyphenylamine)-9,9-spirobifluorene (Spiro-OMeTAD) into CH3NH3PbI3 films along the GBs creates space charge regions to suppress non-radiative recombination and enhance carrier collection efficiency. Solar cells with such activated GBs yielded average PCE of 16.3 0.9%, which are among the best solution-processed perovskite devices. As an important alternative to growing ideal CH3NH3PbI3 single crystal films, which is difficult to achieve for such fast-crystallizing perovskites, activating GBs paves a way to design a new type of bulk heterojunction hybrid perovskite photovoltaics toward theoretical maximum PCE.

  17. Perovskite solar cells with near 100% internal quantum efficiency based on large single crystalline grains and vertical bulk heterojunctions

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Yang, Bin; Dyck, Ondrej; Poplawsky, Jonathan; Keum, Jong; Puretzky, Alexander; Das, Sanjib; Ivanov, Ilia; Rouleau, Christopher; Duscher, Gerd; Geohegan, David; et al

    2015-01-01

    Grain boundaries (GBs) as defects in the crystal lattice detrimentally impact the power conversion efficiency (PCE) of polycrystalline solar cells, particularly in recently emerging hybrid perovskites where non-radiative recombination processes lead to significant carrier losses. Here, the beneficial effects of activated vertical GBs are demonstrated by first growing large, vertically-oriented methylammonium lead tri-iodide (CH3NH3PbI3) single-crystalline grains. We show that infiltration of p-type doped 2 -7,7 -tetrakis(N,Ndi-p-methoxyphenylamine)-9,9-spirobifluorene (Spiro-OMeTAD) into CH3NH3PbI3 films along the GBs creates space charge regions to suppress non-radiative recombination and enhance carrier collection efficiency. Solar cells with such activated GBs yielded average PCE of 16.3 ± 0.9%, whichmore » are among the best solution-processed perovskite devices. As an important alternative to growing ideal CH3NH3PbI3 single crystal films, which is difficult to achieve for such fast-crystallizing perovskites, activating GBs paves a way to design a new type of bulk heterojunction hybrid perovskite photovoltaics toward theoretical maximum PCE.« less

  18. Solar Two

    SciTech Connect (OSTI)

    Not Available

    1998-04-01

    Solar Two is a concentrating solar power plant that can supply electric power on demand to the local utility, Southern California Edison Company. It can do so because it operates not only during sunny parts of the day, but it can store enough thermal energy from the sun to operate during cloudy periods and after dark, for up to three hours, at its rated output of 10 megawatts (MW). For the first time ever, a utility scale solar power plant can supply electricity when the utility needs it most, to satisfy the energy requirements of its customers.

  19. Frequency up-conversion in nonpolar a-plane GaN/AlGaN based multiple quantum wells optimized for applications with silicon solar cells

    SciTech Connect (OSTI)

    Radosavljevi?, S.; Radovanovi?, J. Milanovi?, V.; Tomi?, S.

    2014-07-21

    We have described a method for structural parameters optimization of GaN/AlGaN multiple quantum well based up-converter for silicon solar cells. It involves a systematic tuning of individual step quantum wells by use of the genetic algorithm for global optimization. In quantum well structures, the up-conversion process can be achieved by utilizing nonlinear optical effects based on intersubband transitions. Both single and double step quantum wells have been tested in order to maximize the second order susceptibility derived from the density matrix formalism. The results obtained for single step wells proved slightly better and have been further pursued to obtain a more complex design, optimized for conversion of an entire range of incident photon energies.

  20. Installation-Restoration Program. Phase 2. Confirmation/quantification stage 1 for Minot Air Force Base, Minot, North Dakota. Volume 2. Appendices A through F. Final report, September 1985-October 1988

    SciTech Connect (OSTI)

    Not Available

    1988-10-01

    This document in the appendices A-F for the Installation-Restoration Program Report concerning Minot Air Force Base. The overall objective of the Installation Restoration Program (IRP) Phase II investigation is to assess potential contamination at past hazardous-waste-disposal and spill sites on Air Force installations. A series of stages field investigations may be required to meet this objective. The purpose of this task is to undertake a field investigation at Minot AFB ND to: (1) confirm the presence or absence of contamination within the specified areas of investigation: (2) if possible, determine the extent and degree of contamination and the potential for migration of those contaminants in various environmental media; (3) identify public health and environmental hazards of migrating pollutants based on State or Federal standards for those contaminants; and (4) delineate additional investigations required beyond this stage to reach the Phase II objectives.

  1. High-Efficiency Amorphous Silicon and Nanocrystalline Silicon Based Solar Cells and Modules: Annual Technical Progress Report, 30 January 2006 - 29 January 29, 2007

    SciTech Connect (OSTI)

    Guha, S.; Yang, J.

    2007-07-01

    United Solar used a-Si:H/a-SiGe:H/a-SiGe:H in two manufacturing plants and improved solar efficiency and reduced manufacturing cost by new deposition methods, optimized deposition parameters, and new materials and cell structures.

  2. PROJECT PROFILE: Solar Electric Power Association (Solar Market...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solar Electric Power Association (Solar Market Pathways) PROJECT PROFILE: Solar Electric Power Association (Solar Market Pathways) Title: Community Solar Design Models for ...

  3. Solar Millenium Ridgecrest Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Ridgecrest Solar Power Plant Jump to: navigation, search Name Solar Millenium Ridgecrest Solar Power Plant Facility Solar Millenium Ridgecrest Sector Solar Facility Type...

  4. SES Solar Three Project Solar Power Plant | Open Energy Information

    Open Energy Info (EERE)

    Three Project Solar Power Plant Jump to: navigation, search Name SES Solar Three Project Solar Power Plant Facility SES Solar Three Project Sector Solar Facility Type Photovoltaics...

  5. Renewable Energy Concepts Solar Inc REC Solar | Open Energy Informatio...

    Open Energy Info (EERE)

    Concepts Solar Inc REC Solar Jump to: navigation, search Name: Renewable Energy Concepts Solar Inc (REC Solar) Place: San Luis Obispo, California Zip: 93401 Sector: Solar Product:...

  6. Coulomb force as an entropic force

    SciTech Connect (OSTI)

    Wang Tower

    2010-05-15

    Motivated by Verlinde's theory of entropic gravity, we give a tentative explanation to the Coulomb's law with an entropic force. When trying to do this, we find the equipartition rule should be extended to charges and the concept of temperature should be reinterpreted. If one accepts the holographic principle as well as our generalizations and reinterpretations, then Coulomb's law, the Poisson equation, and the Maxwell equations can be derived smoothly. Our attempt can be regarded as a new way to unify the electromagnetic force with gravity, from the entropic origin. Possibly some of our postulates are related to the D-brane picture of black hole thermodynamics.

  7. Initial validation of FORCE2

    SciTech Connect (OSTI)

    Burge, S.W.

    1991-06-01

    Erosion has been identified as one of the significant design issues in fluid beds. A cooperative R&D venture of industry, research, and government organizations was recently formed to meet the industry need for a better understanding of erosion in fluid beds. Research focussed on bed hydrodynamics, which are considered to be the primary erosion mechanism. As part of this work, ANL developed an analytical model (FLUFIX) for bed hydrodynamics. Partial validation was performed using data from experiments sponsored by the research consortium. Development of a three-dimensional fluid bed hydrodynamic model was part of Asea-Babcock`s in-kind contribution to the R&D venture. This model, FORCE2, was developed by Babcock & Wilcox`s Research and Development Division existing B&W program and on the gas-solids modeling and was based on an existing B&W program and on the gas-solids modeling technology developed by ANL and others. FORCE2 contains many of the features needed to model plant size beds and, therefore can be used along with the erosion technology to assess metal wastage in industrial equipment. As part of the development efforts, FORCE2 was partially validated using ANL`s two-dimensional model, FLUFIX, and experimental data. Time constraints as well as the lack of good hydrodynamic data, particularly at the plant scale, prohibited a complete validation of FORCE2. This report describes this initial validation of FORCE2.

  8. Solar Energy Education. Home economics: teacher's guide. Field test

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    | Department of Energy Community Comes Out in Full Force for SunShot Grand Challenge Summit Solar Community Comes Out in Full Force for SunShot Grand Challenge Summit May 22, 2014 - 10:13am Addthis Packed House 1 of 12 Packed House An energetic crowd of hundreds of leaders throughout the solar community gathered for the 2014 SunShot Grand Challenge Summit to work together to reduce the costs of solar energy technologies. Image: SunShot Initiative, Energy Department. Solar Tech Forum 2 of 12

  9. Solar Circuitry

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Time: 4 to 5 class periods Summary: Students will learn how the solar cell changes light energy to electrical energy. Students will work in small groups and construct different ...

  10. solar energy

    National Nuclear Security Administration (NNSA)

    8%2A en Solar power purchase for DOE laboratories http:nnsa.energy.govmediaroompressreleasessolarpower

  11. solar power

    National Nuclear Security Administration (NNSA)

    9%2A en Solar power purchase for DOE laboratories http:nnsa.energy.govmediaroompressreleasessolarpower

  12. Solar Rights

    Broader source: Energy.gov [DOE]

    In June of 2015, SB 1626 was signed into law. It provides that during the development period, the developer may only prohibit  a property owner from installing solar in developments with 50 or...

  13. Nanocrystal Solar Cells

    SciTech Connect (OSTI)

    Gur, Ilan

    2006-12-15

    This dissertation presents the results of a research agenda aimed at improving integration and stability in nanocrystal-based solar cells through advances in active materials and device architectures. The introduction of 3-dimensional nanocrystals illustrates the potential for improving transport and percolation in hybrid solar cells and enables novel fabrication methods for optimizing integration in these systems. Fabricating cells by sequential deposition allows for solution-based assembly of hybrid composites with controlled and well-characterized dispersion and electrode contact. Hyperbranched nanocrystals emerge as a nearly ideal building block for hybrid cells, allowing the controlled morphologies targeted by templated approaches to be achieved in an easily fabricated solution-cast device. In addition to offering practical benefits to device processing, these approaches offer fundamental insight into the operation of hybrid solar cells, shedding light on key phenomena such as the roles of electrode-contact and percolation behavior in these cells. Finally, all-inorganic nanocrystal solar cells are presented as a wholly new cell concept, illustrating that donor-acceptor charge transfer and directed carrier diffusion can be utilized in a system with no organic components, and that nanocrystals may act as building blocks for efficient, stable, and low-cost thin-film solar cells.

  14. Impact of Rate Design Alternatives on Residential Solar Customer Bills. Increased Fixed Charges, Minimum Bills and Demand-based Rates

    SciTech Connect (OSTI)

    Bird, Lori; Davidson, Carolyn; McLaren, Joyce; Miller, John

    2015-09-01

    With rapid growth in energy efficiency and distributed generation, electric utilities are anticipating stagnant or decreasing electricity sales, particularly in the residential sector. Utilities are increasingly considering alternative rates structures that are designed to recover fixed costs from residential solar photovoltaic (PV) customers with low net electricity consumption. Proposed structures have included fixed charge increases, minimum bills, and increasingly, demand rates - for net metered customers and all customers. This study examines the electricity bill implications of various residential rate alternatives for multiple locations within the United States. For the locations analyzed, the results suggest that residential PV customers offset, on average, between 60% and 99% of their annual load. However, roughly 65% of a typical customer's electricity demand is non-coincidental with PV generation, so the typical PV customer is generally highly reliant on the grid for pooling services.

  15. High-Rate Fabrication of a-Si-Based Thin-Film Solar Cells Using Large-Area VHF PECVD Processes

    SciTech Connect (OSTI)

    Deng, Xunming; Fan, Qi Hua

    2011-12-31

    The University of Toledo (UT), working in concert with its a-Si-based PV industry partner Xunlight Corporation (Xunlight), has conducted a comprehensive study to develop a large-area (3ft x 3ft) VHF PECVD system for high rate uniform fabrication of silicon absorber layers, and the large-area VHF PECVD processes to achieve high performance a-Si/a-SiGe or a-Si/nc-Si tandem junction solar cells during the period of July 1, 2008 to Dec. 31, 2011, under DOE Award No. DE-FG36-08GO18073. The project had two primary goals: (i) to develop and improve a large area (3 ft 3 ft) VHF PECVD system for high rate fabrication of > = 8 /s a-Si and >= 20 /s nc-Si or 4 /s a-SiGe absorber layers with high uniformity in film thicknesses and in material structures. (ii) to develop and optimize the large-area VHF PECVD processes to achieve high-performance a-Si/nc-Si or a-Si/a-SiGe tandem-junction solar cells with >= 10% stable efficiency. Our work has met the goals and is summarized in Accomplishments versus goals and objectives.

  16. Oxford Solar | Open Energy Information

    Open Energy Info (EERE)

    Oxford Solar Jump to: navigation, search Name: Oxford Solar Place: Randolph, New Jersey Zip: 7869 Sector: Solar Product: Oxford Solar provides solar energy consulting and...

  17. Akeena Solar | Open Energy Information

    Open Energy Info (EERE)

    Akeena Solar Jump to: navigation, search Logo: Akeena Solar Name: Akeena Solar Address: 16005 Los Gatos Blvd. Place: Los Gatos, California Zip: 95032 Sector: Solar Product: Solar...

  18. Adobe Solar | Open Energy Information

    Open Energy Info (EERE)

    Adobe Solar Jump to: navigation, search Logo: Adobe Solar Name: Adobe Solar Place: Denver, Colorado Region: Rockies Area Sector: Solar Product: solar electric systems Phone Number:...

  19. Climatic Solar | Open Energy Information

    Open Energy Info (EERE)

    Climatic Solar Jump to: navigation, search Logo: Climatic Solar Name: Climatic Solar Address: 650 2nd Lane Place: Vero Beach, Florida Zip: 32962 Sector: Solar Product: solar energy...

  20. Online National Solar Energy Directory and 2005 Solar Decathlon Product Directory. Final report

    SciTech Connect (OSTI)

    Hamm, Julia; Taylor, Mike

    2008-12-31

    The Solar Electric Power Association (SEPA), in partnership with the American Solar Energy Society, developed an online National Solar Energy Directory with clear, comprehensive information on suppliers and purchasing options. The site was originally located at FindSolar.com, but has recently been moved to Find-Solar.org. The original FindSolar.com domain name has been taken by the American Solar Energy Society (a partner in this project) and utilized for a similar but different project. This Find-Solar.org directory offers the rapidly growing base of potential solar customers a simple, straightforward destination to learn about their solar options. Members of the public are able to easily locate contractors in their geographic area and verify companies?? qualifications with accurate third-party information. It allows consumers to obtain key information on the economics, incentives, desirability, and workings of a solar energy system, as well as competing quotes from different contractors and reviews from customers they have worked with previously. Find-Solar.org is a means of facilitating the growing public interest in solar power and overcoming a major barrier to widespread development of U.S. solar markets. In addition to the development of Find-Solar.org, SEPA developed a separate online product directory for the 2005 DOE Solar Decathlon to facilitate the communication of information about the energy efficiency and renewable energy products used in each university team??s home.

  1. Solar Ready Vets: Preparing Our Veterans to Join the Growing Solar Workforce

    Broader source: Energy.gov [DOE]

    The Solar Ready Vets program is providing our nation's veterans with the skills and training they need for jobs in America's growing solar energy industry. The program is expanding to 10 military bases across the country.

  2. Next-Generation Solar Collectors for CSP

    Broader source: Energy.gov [DOE]

    This fact sheet on Next-Generation Collectors for CSP highlights a solar energy program awarded through the 2012 SunShot Concentrating Solar Power R&D awards. The team is developing new solar collector base technologies for next-generation heliostats used in power tower systems. If successful, this project will result in a 50% reduction in solar field equipment cost and a 30% reduction in field installation cost compared to existing heliostat designs.

  3. Passive solar design handbook. Volume two of two volumes: passive solar design analysis

    SciTech Connect (OSTI)

    Balcomb, J.D.; Barley, D.; McFarland, R.; Perry, J. Jr.; Wray, W.; Noll, S.

    1980-01-01

    A manual for the design and performance evaluation and analysis of passive solar heating systems is presented. Two passive solar building types are analyzed: direct gain and thermal storage walls. Rules of thumb for the schematic design phase and simplified procedures for the design development phase are described. Analysis methods for the construction documents phase are given. The design procedure for fan-forced rock beds for hybrid systems is presented. Economic analysis methods for passive solar buildings are described. Tables of monthly average solar radiation, temperature, and degree-days for various locations in the US and southern Canada are included. (WHK)

  4. MEAM interatomic force calculation subroutine for LAMMPS

    Energy Science and Technology Software Center (OSTI)

    2010-10-25

    Interatomic force and energy calculation subroutine tobe used with the molecular dynamics simulation code LAMMPS (Ref a.). The code evaluates the total energy and atomic forces (energy gradient) according to cubic spine-based variant (Ref b.) of the Modified Embedded Atom Method (MEAM).

  5. NREL: Solar STAT Blog -

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Outreach Policy Basics Publications Request Assistance Technical Assistance Project Map Solar STAT Blog The Solar STAT blog discusses state and local efforts to develop solar...

  6. Solar Resource Assessment

    Broader source: Energy.gov [DOE]

    DOE solar resource research focuses on understanding historical solar resource patterns and making future predictions, both of which are needed to support reliable power system operation. As solar...

  7. Solar heated rotary kiln

    DOE Patents [OSTI]

    Shell, Pamela K. (Tracy, CA)

    1984-01-01

    A solar heated rotary kiln utilized for decomposition of materials, such as zinc sulfate. The rotary kiln has an open end and is enclosed in a sealed container having a window positioned for directing solar energy into the open end of the kiln. The material to be decomposed is directed through the container into the kiln by a feed tube. The container is also provided with an outlet for exhaust gases and an outlet for spent solids, and rests on a tiltable base. The window may be cooled and kept clear of debris by coolant gases.

  8. Elastic actuator for precise force control

    DOE Patents [OSTI]

    Pratt, G.A.; Williamson, M.M.

    1997-07-22

    The invention provides an elastic actuator consisting of a motor and a motor drive transmission connected at an output of the motor. An elastic element is connected in series with the motor drive transmission, and this elastic element is positioned to alone support the full weight of any load connected at an output of the actuator. A single force transducer is positioned at a point between a mount for the motor and an output of the actuator. This force transducer generates a force signal, based on deflection of the elastic element, that indicates force applied by the elastic element to an output of the actuator. An active feedback force control loop is connected between the force transducer and the motor for controlling the motor. This motor control is based on the force signal to deflect the elastic element an amount that produces a desired actuator output force. The produced output force is substantially independent of load motion. The invention also provides a torsional spring consisting of a flexible structure having at least three flat sections each connected integrally with and extending radially from a central section. Each flat section extends axially along the central section from a distal end of the central section to a proximal end of the central section. 30 figs.

  9. Elastic actuator for precise force control

    DOE Patents [OSTI]

    Pratt, Gill A.; Williamson, Matthew M.

    1997-07-22

    The invention provides an elastic actuator consisting of a motor and a motor drive transmission connected at an output of the motor. An elastic element is connected in series with the motor drive transmission, and this elastic element is positioned to alone support the full weight of any load connected at an output of the actuator. A single force transducer is positioned at a point between a mount for the motor and an output of the actuator. This force transducer generates a force signal, based on deflection of the elastic element, that indicates force applied by the elastic element to an output of the actuator. An active feedback force control loop is connected between the force transducer and the motor for controlling the motor. This motor control is based on the force signal to deflect the elastic element an amount that produces a desired actuator output force. The produced output force is substantially independent of load motion. The invention also provides a torsional spring consisting of a flexible structure having at least three flat sections each connected integrally with and extending radially from a central section. Each flat section extends axially along the central section from a distal end of the central section to a proximal end of the central section.

  10. Molecular helices as electron acceptors in high-performance bulk heterojunction solar cells

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Yu M. Zhong; Nam, Chang -Yong; Trinh, M. Tuan; Chen, Rongsheng; Purdum, Geoffrey E.; Khlyabich, Petr P.; Sezen, Melda; Oh, Seokjoon; Zhu, Haiming; Fowler, Brandon; et al

    2015-09-18

    Despite numerous organic semiconducting materials synthesized for organic photovoltaics in the past decade, fullerenes are widely used as electron acceptors in highly efficient bulk-heterojunction solar cells. None of the non-fullerene bulk heterojunction solar cells have achieved efficiencies as high as fullerene-based solar cells. Design principles for fullerene-free acceptors remain unclear in the field. Here we report examples of helical molecular semiconductors as electron acceptors that are on par with fullerene derivatives in efficient solar cells. We achieved an 8.3% power conversion efficiency in a solar cell, which is a record high for non-fullerene bulk heterojunctions. Femtosecond transient absorption spectroscopy revealedmore » both electron and hole transfer processes at the donor–acceptor interfaces. Atomic force microscopy reveals a mesh-like network of acceptors with pores that are tens of nanometres in diameter for efficient exciton separation and charge transport. As a result, this study describes a new motif for designing highly efficient acceptors for organic solar cells.« less

  11. Molecular helices as electron acceptors in high-performance bulk heterojunction solar cells

    SciTech Connect (OSTI)

    Yu M. Zhong; Nam, Chang -Yong; Trinh, M. Tuan; Chen, Rongsheng; Purdum, Geoffrey E.; Khlyabich, Petr P.; Sezen, Melda; Oh, Seokjoon; Zhu, Haiming; Fowler, Brandon; Zhang, Boyuan; Wang, Wei; Sfeir, Matthew Y.; Black, Charles T.; Steigerwald, Michael L.; Loo, Yueh -Lin; Ng, Fay; Zhu, X. -Y.; Nuckolls, Colin

    2015-09-18

    Despite numerous organic semiconducting materials synthesized for organic photovoltaics in the past decade, fullerenes are widely used as electron acceptors in highly efficient bulk-heterojunction solar cells. None of the non-fullerene bulk heterojunction solar cells have achieved efficiencies as high as fullerene-based solar cells. Design principles for fullerene-free acceptors remain unclear in the field. Here we report examples of helical molecular semiconductors as electron acceptors that are on par with fullerene derivatives in efficient solar cells. We achieved an 8.3% power conversion efficiency in a solar cell, which is a record high for non-fullerene bulk heterojunctions. Femtosecond transient absorption spectroscopy revealed both electron and hole transfer processes at the donor–acceptor interfaces. Atomic force microscopy reveals a mesh-like network of acceptors with pores that are tens of nanometres in diameter for efficient exciton separation and charge transport. As a result, this study describes a new motif for designing highly efficient acceptors for organic solar cells.

  12. Protective Force Program Manual

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-12-20

    Provides detailed requirements to supplement DOE O 473.2, PROTECTIVE FORCE PROGRAM, which establishes the requirements and responsibilities for management and operation of the Department of Energy (DOE) Protective Force (PF) Program. Change 1 revised pages in Chapters IV and VI on 12/20/2001.

  13. I-III-VI.sub.2 based solar cell utilizing the structure CuInGaSe.sub.2 CdZnS/ZnO

    DOE Patents [OSTI]

    Chen, Wen S.; Stewart, John M.

    1992-01-07

    A thin film I-III-VI.sub.2 based solar cell having a first layer of copper indium gallium selenide, a second layer of cadmium zinc sulfide, a double layer of zinc oxide, and a metallization structure comprised of a layer of nickel covered by a layer of aluminum. An optional antireflective coating may be placed on said metallization structure. The cadmium zinc sulfide layer is deposited by means of an aqueous solution growth deposition process and may actually consist of two layers: a low zinc content layer and a high zinc content layer. Photovoltaic efficiencies of 12.5% at Air Mass 1.5 illumination conditions and 10.4% under AMO illumination can be achieved.

  14. Reconstruction and Prediction of Variations of Total Ozone and Associated Variations of UV-B Solar Radiation for Subarctic Regions Based of Dendrochronologic Data

    SciTech Connect (OSTI)

    Zuev, V.V.; Bondarenko, S.L.

    2005-03-18

    Variations of dendrochronologic parameters, especially annual ring density, significantly reflect the physiological tree response to systematic variations of solar UV-B radiation, taking place on monthly and longer timescales during growing season. Such variations of UV-B radiation are totally governed by variations of total ozone (TO). Thus, in any dendrochronologic signal, especially for coniferous trees, there is also a recorded response to TO variations, characterizing variations of UV-B radiation. Because a monitoring of global TO distribution is regularly performed since 1979 using TOMS satellite instrumentation, there appears a possibility to reconstruct TO behavior in the past practically at any point of dendrochronologic monitoring network. The reconstruction is performed by the method of linear regression, based on significant correlation of annual ring density of coniferous trees and TO for coordinates of denrochronologic signal. The present report considers the Subarctic latitudes, which are characterized by considerable TO variations in the second half of twentieth century.

  15. Georgia Power- Solar Buyback Program

    Broader source: Energy.gov [DOE]

    Georgia Power, the state's largest utility, has established a green power program, that allows the company to purchase limited solar generation at a premium price based on other customers volunta...

  16. Gadir Solar | Open Energy Information

    Open Energy Info (EERE)

    Name: Gadir Solar Place: Madrid, Spain Zip: 28001 Product: Madrid-based manufacturer of thin-film silicon PV modules. Coordinates: 40.4203, -3.705774 Show Map Loading map......

  17. Solar BG | Open Energy Information

    Open Energy Info (EERE)

    BG - 1784 Sector: Wind energy Product: Bulgarian based company investing into hybrid wind-PV plants. References: Solar BG1 This article is a stub. You can help OpenEI by...

  18. Transform Solar | Open Energy Information

    Open Energy Info (EERE)

    search Name: Transform Solar Place: Boise, Idaho Product: Idaho-based PV module maker and joint venture between Micron and Origin Energy. Coordinates: 43.60698, -116.193409...

  19. Solar Technology Acceleration Center (SolarTAC): Solar Resource & Meteorological Assessment Project (SOLRMAP); Aurora, Colorado (Data)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Wilcox, S.; Andreas, A.

    Located in Colorado, near Denver International Airport, SolarTAC is a private, member-based, 74-acre outdoor facility where the solar industry tests, validates, and demonstrates advanced solar technologies. SolarTAC was launched in 2008 by a public-private consortium, including Midwest Research Institute (MRI). As a supporting member of SolarTAC, the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) has established a high quality solar and meteorological measurement station at this location. This Solar Resource and Meteorological Assessment Project (SOLRMAP) provides high quality measurements to support deployment of power projects in the United States. The no-funds-exchanged collaboration brings NREL solar resource assessment expertise together with industry needs for measurements. The end result is high quality data sets to support the financing, design, and monitoring of large scale solar power projects for industry in addition to research-quality data for NREL model development. NREL provides consultation for instrumentation and station deployment, along with instrument calibrations, data acquisition, quality assessment, data distribution, and summary reports. Industry participants provide equipment, infrastructure, and station maintenance.

  20. Solar Technology Acceleration Center (SolarTAC): Solar Resource & Meteorological Assessment Project (SOLRMAP); Aurora, Colorado (Data)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Wilcox, S.; Andreas, A.

    2011-02-11

    Located in Colorado, near Denver International Airport, SolarTAC is a private, member-based, 74-acre outdoor facility where the solar industry tests, validates, and demonstrates advanced solar technologies. SolarTAC was launched in 2008 by a public-private consortium, including Midwest Research Institute (MRI). As a supporting member of SolarTAC, the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) has established a high quality solar and meteorological measurement station at this location. This Solar Resource and Meteorological Assessment Project (SOLRMAP) provides high quality measurements to support deployment of power projects in the United States. The no-funds-exchanged collaboration brings NREL solar resource assessment expertise together with industry needs for measurements. The end result is high quality data sets to support the financing, design, and monitoring of large scale solar power projects for industry in addition to research-quality data for NREL model development. NREL provides consultation for instrumentation and station deployment, along with instrument calibrations, data acquisition, quality assessment, data distribution, and summary reports. Industry participants provide equipment, infrastructure, and station maintenance.

  1. Solar Policy Environment: Minneapolis/St. Paul

    Broader source: Energy.gov [DOE]

    The cities of Minneapolis and St. Paul joined forces to implement a comprehensive approach to promoting “Solar in the Cities” including commercial and residential solar installations, technical training programs, and city and state policy review. The Cities are marshalling a wide array of expertise through strategic partnerships with Xcel Energy, Minnesota Dept. of Commerce, Minnesota Renewable Energy Society, Green Institute, freEner-g, Int’l Brotherhood of Electrical Workers, League of Minnesota cities, Neighborhood Energy Connection, and Century College.

  2. A New Method of Comparing Forcing Agents in Climate Models

    SciTech Connect (OSTI)

    Kravitz, Benjamin S.; MacMartin, Douglas; Rasch, Philip J.; Jarvis, Andrew

    2015-10-14

    We describe a new method of comparing different climate forcing agents (e.g., CO2, CH4, and solar irradiance) that avoids many of the ambiguities introduced by temperature-related climate feedbacks. This is achieved by introducing an explicit feedback loop external to the climate model that adjusts one forcing agent to balance another while keeping global mean surface temperature constant. Compared to current approaches, this method has two main advantages: (i) the need to define radiative forcing is bypassed and (ii) by maintaining roughly constant global mean temperature, the effects of state dependence on internal feedback strengths are minimized. We demonstrate this approach for several different forcing agents and derive the relationships between these forcing agents in two climate models; comparisons between forcing agents are highly linear in concordance with predicted functional forms. Transitivity of the relationships between the forcing agents appears to hold within a wide range of forcing. The relationships between the forcing agents obtained from this method are consistent across both models but differ from relationships that would be obtained from calculations of radiative forcing, highlighting the importance of controlling for surface temperature feedback effects when separating radiative forcing and climate response.

  3. High Efficiency Amorphous and Microcrystalline Silicon Based Double-Junction Solar Cells made with Very-High-Frequency Glow Discharge

    SciTech Connect (OSTI)

    Banerjee, Arindam

    2004-10-20

    We have achieved a total-area initial efficiency of 11.47% (active-area efficiency of 12.33%) on a-Si:H/?c-Si:H double-junction structure, where the intrinsic layer bottom cell was made in 50 minutes. On another device in which the bottom cell was made in 30 min, we achieved initial total-area efficiency of 10.58% (active-efficiency of 11.35%). We have shown that the phenomenon of ambient degradation of both ?c-Si:H single-junction and a-Si:H/?c-Si:H double-junction cells can be attributed to impurity diffusion after deposition. Optimization of the plasma parameters led to alleviation of the ambient degradation. Appropriate current matching between the top and bottom component cells has resulted in a stable total-area efficiency of 9.7% (active-area efficiency of 10.42%) on an a-Si:H/?c-Si:H double-junction solar cell in which the deposition time for the ?c-Si:H intrinsic layer deposition was of 30 min.

  4. High Resolution Dopant Profiles Revealed by Atom Probe Tomography and STEM-EBIC for CdTe Based Solar Cells

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Poplawsky, Jonathan D.; Li, Chen; Paudel, Naba; Guo, Wei; Yan, Yanfa; Pennycook, Stephen J.

    2016-01-01

    Segregated elements and their diffusion profiles within grain boundaries and interfaces resulting from post deposition heat treatments are revealed using atom probe tomography (APT), scanning transmission electron microscopy (STEM), and electron beam induced current (EBIC) techniques. The results demonstrate how these techniques complement each other to provide conclusive evidence for locations of space charge regions and mechanisms that create them at the nanoscale. Most importantly, a Cl dopant profile that extends ~5 nm into CdTe grains interfacing the CdS is shown using APT and STEM synergy, which has been shown to push the pn-junction into the CdTe layer indicative ofmore » a homojunction (revealed by STEM EBIC). In addition, Cu and Cl concentrations within grain boundaries within several nms and µms from the CdS/CdTe interface are compared, Na segregation of <0.1% is detected, and S variations of ~1–3% are witnessed between CdTe grains close to the CdS/CdTe interface. The segregation and diffusion of these elements directly impacts on the material properties, such as band gap energy and n/p type properties. Optimization of the interfacial and grain boundary doping will lead to higher efficiency solar cells.« less

  5. High Resolution Dopant Profiles Revealed by Atom Probe Tomography and STEM-EBIC for CdTe Based Solar Cells

    SciTech Connect (OSTI)

    Poplawsky, Jonathan D.; Li, Chen; Paudel, Naba; Guo, Wei; Yan, Yanfa; Pennycook, Stephen J.

    2016-01-01

    Segregated elements and their diffusion profiles within grain boundaries and interfaces resulting from post deposition heat treatments are revealed using atom probe tomography (APT), scanning transmission electron microscopy (STEM), and electron beam induced current (EBIC) techniques. The results demonstrate how these techniques complement each other to provide conclusive evidence for locations of space charge regions and mechanisms that create them at the nanoscale. Most importantly, a Cl dopant profile that extends ~5 nm into CdTe grains interfacing the CdS is shown using APT and STEM synergy, which has been shown to push the pn-junction into the CdTe layer indicative of a homojunction (revealed by STEM EBIC). In addition, Cu and Cl concentrations within grain boundaries within several nms and µms from the CdS/CdTe interface are compared, Na segregation of <0.1% is detected, and S variations of ~1–3% are witnessed between CdTe grains close to the CdS/CdTe interface. The segregation and diffusion of these elements directly impacts on the material properties, such as band gap energy and n/p type properties. Optimization of the interfacial and grain boundary doping will lead to higher efficiency solar cells.

  6. Residential Solar Valuation Rates

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solar Valuation Rates Karl R. Rbago Rbago Energy LLC 1 The Ideal Residential Solar Tariff Fair to the utility and non-solar customers Fair compensation to the solar ...

  7. Solar Equipment Certification

    Broader source: Energy.gov [DOE]

    Under the Solar Energy Standards Act of 1976, the Florida Solar Energy Center (FSEC) is responsible for certifying all solar equipment sold in Florida. A manufacturer who wishes to have their solar...

  8. Zenith Solar Ltd | Open Energy Information

    Open Energy Info (EERE)

    Zenith Solar Ltd Place: Qiryat Gat, Israel Zip: 82000 Product: Israel-based developers of a HCPV - highly concentrator PV system for residential and industrial use. References:...

  9. GCL Solar Ltd | Open Energy Information

    Open Energy Info (EERE)

    Ltd Jump to: navigation, search Name: GCL Solar Ltd Place: Nanjing, Jiangsu Province, China Zip: 210008 Sector: Services Product: China-based PV engineering contractor, offering...

  10. Solar India Solutions | Open Energy Information

    Open Energy Info (EERE)

    Visakhapatnam, Andhra Pradesh, India Zip: 530016 Sector: Efficiency Product: Andhra-based energy efficiency consultant. References: Solar India Solutions1 This article is a stub....

  11. Solar Technologies Installations Ltd | Open Energy Information

    Open Energy Info (EERE)

    Installations Ltd Jump to: navigation, search Name: Solar Technologies Installations Ltd Place: Hampshire, United Kingdom Zip: S051 OHR Sector: Renewable Energy Product: A UK-based...

  12. ATERSA Electridad Solar | Open Energy Information

    Open Energy Info (EERE)

    Electridad Solar Place: Madrid, Spain Zip: 28045 Product: Madrid-based manufacturer of PV modules and balance of plant such as mounting and inverters; commercial and residential...

  13. Solar Fabrik AG | Open Energy Information

    Open Energy Info (EERE)

    Zip: 79111 Product: Freiburg-based manufacturer of wafers, PV cells, modules and inverters, largely through acquisitions. References: Solar Fabrik AG1 This article is a...

  14. US Solar Distributing | Open Energy Information

    Open Energy Info (EERE)

    Distributing Place: California Product: California-based distributor of PV modules, inverters, mounting systems and accessories. References: US Solar Distributing1 This article...

  15. SolarWrights Inc | Open Energy Information

    Open Energy Info (EERE)

    Inc Place: Stonington, Rhode Island Zip: 6378 Sector: Renewable Energy, Solar, Wind energy Product: Rhode Island-based private company specialising in the design and...

  16. Ajit Solar Pvt Ltd | Open Energy Information

    Open Energy Info (EERE)

    Solar Pvt Ltd Place: Jaipur, Rajasthan, India Zip: 302001 Product: Jaipur-based PV module manufacturer. Coordinates: 26.89876, 75.79636 Show Map Loading map......

  17. Moon Solar Light MSL | Open Energy Information

    Open Energy Info (EERE)

    Product: developed and distributes solar-based lighting applications using PV panels, LED lights and ultra-capacitors. Coordinates: 31.899309, 34.807999 Show Map Loading...

  18. The Solar Storage Company | Open Energy Information

    Open Energy Info (EERE)

    Company Place: Palo Alto, California Zip: 1704 Product: US-based start-up developing energy production and storage systems. References: The Solar Storage Company1 This...

  19. South West Solar Power | Open Energy Information

    Open Energy Info (EERE)

    Power Jump to: navigation, search Name: South West Solar Power Place: Gwangju Metropolitan City, Korea (Republic) Product: Korea-based company acting as the operating body for the...

  20. ESL Solar Co Ltd | Open Energy Information

    Open Energy Info (EERE)

    search Name: ESL Solar Co Ltd Place: Ningbo, Zhejiang Province, China Product: Assembles PV modules and PV-based systems such as lanterns, flashlights, and camping lights....