Powered by Deep Web Technologies
Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Fire protection countermeasures for containment ventilation systems  

SciTech Connect

The goal of this project is to find countermeasures to protect High Efficiency Particulate Air (HEPA) filters, in exit ventilation ducts, from the heat and smoke generated by fire. Initially, methods were developed to cool fire-heated air by fine water spray upstream of the filters. It was recognized that smoke aerosol exposure to HEPA filters could also cause disruption of the containment system. Through testing and analysis, several methods to partially mitigate the smoke exposure to the HEPA filters were identified. A continuous, movable, high-efficiency prefilter using modified commercial equipment was designed. The technique is capable of protecting HEPA filters over the total time duration of the test fires. The reason for success involved the modification of the prefiltration media. Commercially available filter media has particle sorption efficiency that is inversely proportional to media strength. To achieve properties of both efficiency and strength, rolling filter media were laminated with the desired properties. The approach was Edisonian, but truncation in short order to a combination of prefilters was effective. The application of this technique was qualified, since it is of use only to protect HEPA filters from fire-generated smoke aerosols. It is not believed that this technique is cost effective in the total spectrum of containment systems, especially if standard fire protection systems are available in the space. But in areas of high-fire risk, where the potential fuel load is large and ignition sources are plentiful, the complication of a rolling prefilter in exit ventilation ducts to protect HEPA filters from smoke aerosols is definitely justified.

Alvares, N.; Beason, D.; Bergman, V.; Creighton, J.; Ford, H.; Lipska, A.

1980-08-25T23:59:59.000Z

2

Fire Protection System Account Request Form | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection System Account Request Form Fire Protection System Account Request Form Fire Protection System Account Request Form December 2, 2010 Account request form used to obtain user credentials for the Fire Protection Database To obtain a user id and password to access the Fire Protection system, please complete the form, save the file and email it to HSSUserSupport@hq.doe.gov or print and fax it to 301-903-9823. We will provide a username and password to new account holders. Please allow several business days to process your account request. When your request is approved, you will be contacted with your account information. Fire Protection System Account Request Form More Documents & Publications CAIRS Registration Form Microsoft Word - PARS II User Acct Access Guide.rtf PARS Domain User Maintenance Function Support Team Guide (v

3

Fire protection system operating experience review for fusion applications  

SciTech Connect

This report presents a review of fire protection system operating experiences from particle accelerator, fusion experiment, and other applications. Safety relevant operating experiences and accident information are discussed. Quantitative order-of-magnitude estimates of fire protection system component failure rates and fire accident initiating event frequencies are presented for use in risk assessment, reliability, and availability studies. Safety concerns with these systems are discussed, including spurious operation. This information should be useful to fusion system designers and safety analysts, such as the team working on the Engineering Design Activities for the International Thermonuclear Experimental Reactor.

Cadwallader, L.C.

1995-12-01T23:59:59.000Z

4

Independent Oversight Review of the Fire Protection Program and Fire Protection Systems at the Transuranic Waste Processing Center, December 2013  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and Fire Protection Systems and Fire Protection Systems at the Transuranic Waste Processing Center December 2013 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U. S. Department of Energy Table of Contents 1.0 Purpose.................................................................................................................................................... 1 2.0 Background ............................................................................................................................................. 1 3.0 Scope....................................................................................................................................................... 2 4.0 Methodology .......................................................................................................................................... 2

5

Fire Protection  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NOT MEASUREMENT NOT MEASUREMENT SENSITIVE DOE-STD-1066-2012 December 2012 _______________ Supersedes DOE-STD-1066-99 DOE STANDARD FIRE PROTECTION U.S. Department of Energy AREA FIRP Washington, DC 20585 DISTRIBUTION STATEMENT. Approved for public release; distribution is unlimited. This document is available on the Department of Energy Technical Standards Program Web page at http://www.hss.doe.gov/nuclearsafety/ns/techstds/ DOE-STD-1066-2012 FOREWORD This Department of Energy (DOE) Standard (STD) supersedes DOE-STD-1066-99 1 and is approved for use by DOE and its contractors. The following fire protection standard is canceled with the issuance of this Standard and appropriate technical content was incorporated into this Standard: ď‚· DOE-STD-1088-95, Fire Protection for Relocatable Structures

6

Fire Protection  

Science Conference Proceedings (OSTI)

... This is not a do-it-yourself job and should be left to a qualified contractor. Never paint sprinklers, it can prevent them from operating in a fire. ...

2013-08-26T23:59:59.000Z

7

Guideline for the Evaluation and Treatment of Corrosion and Fouling in Fire Protection Systems  

Science Conference Proceedings (OSTI)

This guideline document addresses the methods to control and mitigate corrosion, fouling, and microbiological growth in water-related fire protection systems (FPSs).

1999-03-30T23:59:59.000Z

8

Cold Vacuum Dryer (CVD) Facility Fire Protection System Design Description (SYS 24)  

SciTech Connect

This system design description (SDD) addresses the Cold Vacuum Drying (CVD) Facility fire protection system (FPS). The primary features of the FPS for the CVD are a fire alarm and detection system, automatic sprinklers, and fire hydrants. The FPS also includes fire extinguishers located throughout the facility and fire hydrants to assist in manual firefighting efforts. In addition, a fire barrier separates the operations support (administrative) area from the process bays and process bay support areas. Administrative controls to limit combustible materials have been established and are a part of the overall fire protection program. The FPS is augmented by assistance from the Hanford Fire Department (HED) and by interface systems including service water, electrical power, drains, instrumentation and controls. This SDD, when used in conjunction with the other elements of the definitive design package, provides a complete picture of the FPS for the CVD Facility.

SINGH, G.

2000-10-17T23:59:59.000Z

9

Fire Protection Program Manual  

Science Conference Proceedings (OSTI)

This manual documents the Lawrence Livermore National Laboratory (LLNL) Fire Protection Program. Department of Energy (DOE) Orders 420.1B, Facility Safety, requires LLNL to have a comprehensive and effective fire protection program that protects LLNL personnel and property, the public and the environment. The manual provides LLNL and its facilities with general information and guidance for meeting DOE 420.1B requirements. The recommended readers for this manual are: fire protection officers, fire protection engineers, fire fighters, facility managers, directorage assurance managers, facility coordinators, and ES and H team members.

Sharry, J A

2012-05-18T23:59:59.000Z

10

Fire Protection Program: Related Sites  

NLE Websites -- All DOE Office Websites (Extended Search)

Office of Science Brookhaven National Laboratory Hanford Fire Department CPSC OSHA NRC EPA FEMA National Fire Academy Fire Protection Association Australia National Fire...

11

Fire Protection Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Program Program Fire Protection Overview The Department of Energy (DOE) Fire Protection Program is multi-faceted. It includes published fire safety directives (Orders, standards, and guidance documents), a range of oversight activities, an annual fire protection program summary, and a directory of fire safety professionals. DOE also sponsors fire safety conferences, various training initiatives, and a spectrum of technical assistance activities. This Home Page is intended to bring together in one location as much of the Program's resources as possible to facilitate greater understanding, communication, and efficiency of operations. Guidelines -- NFPA Codes and standards, CFRs, and DOE Directives (policy statements, Orders, Standards, and Guidance Documents)

12

Cold Vacuum Drying facility fire protection system design description (SYS 24)  

SciTech Connect

This document describes the Cold Vacuum Drying Facility (CVDF) fire protection system (FPS). The FPS provides fire detection, suppression, and loss limitation for the CVDF structure, personnel, and in-process spent nuclear fuel. The system provides, along with supporting interfacing systems, detection, alarm, and activation instrumentation and controls, distributive piping system, isolation valves, and materials and controls to limit combustibles and the associated fire loadings.

PITKOFF, C.C.

1999-07-06T23:59:59.000Z

13

Fire Protection Program Guidelines  

NLE Websites -- All DOE Office Websites (Extended Search)

Guidelines Principal Orders Related Orders Technical Standards Guidance Current fire protection requirements of the Department reside in: DOE O 420.1C, "Facility Safety", 10 CFR...

14

Fire Protection Account Request Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection System Account Request Form Fire Protection System Account Request Form To obtain a user id and password to access the Fire Protection system, please complete the form, save the file and email it to hssUserSupport@hq.doe.gov or print and fax it to 301-903-9823. We will provide a username and password to new account holders. Please allow several business days to process your account request. When your request is approved, you will be contacted with your

15

CRAD, Fire Protection - October 12, 2012 | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection - October 12, 2012 Fire Protection - October 12, 2012 CRAD, Fire Protection - October 12, 2012 October 12, 2012 Fire Protection Inspection Criteria, Approach, and Lines of Inquiry HSS CRAD 45-34, Rev. 1) Review fire protection system design and defense in-depth strategies. Interviews shall be conducted of personnel including fire engineers, fire coordinators, fire system technicians, facility operations personnel, and fire department personnel. Review policies, procedures, fire hazards analyses, and safety basis documentation. Additionally, perform facility building walk downs and inspections, and observe selected work activities, such as hot work, fire system impairments, combustible storage practices, dispensing flammable liquids, maintenance and testing of fire protection

16

Design criteria document, Fire Protection Task, K Basin Essential Systems Recovery, Project W-405  

Science Conference Proceedings (OSTI)

The K Basin were constructed in the early 1950`s with a 20 year design life. The K Basins are currently in their third design life and are serving as a near term storage facility for irradiated N Reactor fuel until an interim fuel storage solution can be implemented. In April 1994, Project W-405, K Basin Essential Systems Recovery, was established to address (among other things) the immediate fire protection needs of the 100K Area. A Fire Barrier Evaluation was performed for the wall between the active and inactive areas of the 105KE and 105KW buildings. This evaluation concludes that the wall is capable of being upgraded to provide an equivalent level of fire resistance as a qualified barrier having a fire resistance rating of 2 hours. The Fire Protection Task is one of four separate Tasks included within the scope of Project W405, K Basin Essential systems Recovery. The other three Tasks are the Water Distribution System Task, the Electrical System Task, and the Maintenance Shop/Support Facility Task. The purpose of Project W-405`s Fire Protection Task is to correct Life Safety Code (NFPA 101) non-compliances and to provide fire protection features in Buildings 105KE, 105KW and 190KE that are essential for assuring the safe operation and storage of spent nuclear fuel at the 100K Area Facilities` Irradiated Fuel Storage Basins (K Basins).

Johnson, B.H.

1994-12-14T23:59:59.000Z

17

Spray booth with energy saving and fire protection systems  

SciTech Connect

This invention teaches an improved exhaust system to be used with a paint spray booth and having a continuously operating power exhaust fan. The exhaust system has a damper that is opened when spraying actively is taking place in the spray booth and that is closed when there is no spraying actively taking place in the spray booth. A control switch is mounted in any of several locations to determine when the spray gun is in use or is not in use. Thus, the control switch is actuated when the spray gun is hung up thus indicating a nonuse condition of the spray system; whereupon use of the spray gun lifts the gun from the hook to indicate spraying activity. A motor drives the damper to the opened position; and a spring biases the damper to the closed position. A timer is also used to delay the closing of the damper until between twenty and possibly two hundred seconds have lapsed after spraying activity has terminated. This purges the spray booth while yet allows for automatic damper control under normal spraying sequences of use and nonuse. A fire sensing switch is used to deenergize the damper motor to allow the damper to be closed in the event of a fire.

Napadow, S.C.

1980-09-23T23:59:59.000Z

18

Fire Protection Program: Summary  

NLE Websites -- All DOE Office Websites (Extended Search)

Summary Summary Since May 1950, an Annual Fire Protection Program Summary has been submitted by DOE's fire protection community. Currently, this report is required by section 5a.(8) of DOE Order 231.1. "Environment, Safety and Health Reporting." In 1999, an automation initiative was undertaken to streamline data collection and provide a more through review of DOE Reporting Element activities. This action resulted in the delayed publications of the CY 1999 and 2000 reports until 2002. It is now possible however to view all Annual Summary Reporting Element responses since 1991 at the Site, Operations, Lead Program Secretarial Office and Headquarters levels. Additionally, a build-in reference to other DOE reporting activities (CAIRS and ORPS) is available that allows Reporting Elements and managers the opportunity to review all fire protection events along previously mentioned categories. Reports listed below were generated from this application. To obtain a copy of the Annual Summary Application please contact Jim Bisker in the Office of Nuclear and Facility Safety Policy (EH-53) at (301)903-6542 or Jim Bisker.

19

Independent Oversight Review of the Fire Protection Program at the Pacific Northwest National Laboratory and the Fire Suppression System at the Radiochemical Processing Laboratory, September 2013  

NLE Websites -- All DOE Office Websites (Extended Search)

Independent Oversight Review of the Independent Oversight Review of the Fire Protection Program at Pacific Northwest National Laboratory and the Fire Suppression System at the Radiochemical Processing Laboratory May 2011 February 2013 September 2013 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy Table of Contents 1.0 Purpose.................................................................................................................................................... 1 2.0 Background ............................................................................................................................................. 1 3.0 Scope....................................................................................................................................................... 2

20

Independent Oversight Review of the Fire Protection Program at the Pacific Northwest National Laboratory and the Fire Suppression System at the Radiochemical Processing Laboratory, September 2013  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Independent Oversight Review of the Independent Oversight Review of the Fire Protection Program at Pacific Northwest National Laboratory and the Fire Suppression System at the Radiochemical Processing Laboratory May 2011 February 2013 September 2013 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy Table of Contents 1.0 Purpose.................................................................................................................................................... 1 2.0 Background ............................................................................................................................................. 1 3.0 Scope....................................................................................................................................................... 2

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Topic: Fire Protection Technologies  

Science Conference Proceedings (OSTI)

... NIST Evaluates Firefighting Tactics In NYC High-Rise ... Fire Modeling for Performance-Based Design Project. Safety of Building Occupants Projects. ...

2012-09-19T23:59:59.000Z

22

Fire Protection Program: Training  

NLE Websites -- All DOE Office Websites (Extended Search)

Training DOE IAFF Training for Radiation Emergencies Hanford Fire Department Radiation Fundamentals for Emergency Responders For more information contact: Jim Bisker This page...

23

Fire Protection Technologies Software  

Science Conference Proceedings (OSTI)

... Sprinkler Use Decisioning is a Web-tool designed to facilitate economic analysis of residential fire sprinklers at the homeowner-and … more. ...

2010-12-01T23:59:59.000Z

24

Fire Protection Technologies Portal  

Science Conference Proceedings (OSTI)

... Sprinkler Use Decisioning is a Web-tool designed to facilitate economic analysis of residential fire sprinklers at the homeowner-and … more. ...

2013-04-11T23:59:59.000Z

25

Fire Protection Database | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection Database Fire Protection Database Fire Protection Database DOE O 231.1, Environment, Safety, And Health Reporting, requires the submission of an Annual Fire Protection Summary. The previous process used to collect the required data utilizes a Microsoft Access database that was downloaded, completed by the field and then sent to Headquarters for summation and analysis by engineers in Office of Sustainability Support. Data collection for the CY2013 Summary will begin Jan. 1, 2014, and a commitment has been made to the Defense Nuclear Facilities Safety Board to collect this information and make it available utilizing a standard systematic approach. This approach will be accomplished via a web based system which will allow reporting organizations to enter or edit information.

26

SIL rating fire protection equipment  

Science Conference Proceedings (OSTI)

SIL's (Safety Integrity Levels) are used by IEC 61508:1998 [1] to characterise the required functional safety of computer control systems. For example, SIL 4, the highest rating is for fly by wire aircraft and weapons systems and track circuited train ... Keywords: SIL, fire control panels, fire systems

Richard M. Robinson; Kevin J. Anderson

2003-10-01T23:59:59.000Z

27

Fire Protection Engineering Qualification Standard Reference Guide  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection Fire Protection Engineering Qualification Standard Reference Guide SEPTEMBER 2009 This page is intentionally blank. Table of Contents i ACRONYMS ................................................................................................................................. ii PURPOSE.......................................................................................................................................1 SCOPE ............................................................................................................................................1 PREFACE.......................................................................................................................................1 TECHNICAL COMPETENCIES................................................................................................3

28

June 12, 2006 AUTOMATIC SPRINKLERS AND WATER BASED FIRE PROTECTION SYSTEMS  

E-Print Network (OSTI)

Cost Actual FY Reconciled Cost* 2007 41 9 110 $30,351.46 $39,651.85 $162,515.63 2008 35 12 59 $44 of the Quarter Award 2010 state Fire Marshal's conference NFPA 101 life safety code course Corrected compliance drills EH&S fire extinguisher trainer Installation of building lay-out maps OSHA 10 Hour Training NFPA 70

29

FAQS Job Task Analyses - Fire Protection Engineering  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Job Task Analysis and Competency Review Job Task Analysis and Competency Review for All Level Competencies Fire Protection Engineering FAQS Initially conducted (expert competencies): August 2010 Updated (includes ALL Competencies): April 2011 Updated (includes ALL Competencies): October 2012 STEP 1: Job Task Analysis for Tasks Task (and Number) Source Importance Frequency Serve as the subject matter expert in the area of fire protection, life safety, and fire department emergency related services. FAQS Duties and Responsibilities Paragraph A 5 4 Review fire hazard analyses, assessments, and other fire safety documentation for compliance with applicable requirements. FAQS Duties and Responsibilities Paragraph B 5 3 Evaluate the adequacy of site emergency services. This includes all facets of the fire

30

FAQS Qualification Card - Fire Protection | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection Fire Protection FAQS Qualification Card - Fire Protection A key element for the Department's Technical Qualification Programs is a set of common Functional Area Qualification Standards (FAQS) and associated Job Task Analyses (JTA). These standards are developed for various functional areas of responsibility in the Department, including oversight of safety management programs identified as hazard controls in Documented Safety Analyses (DSA). For each functional area, the FAQS identify the minimum technical competencies and supporting knowledge and skills for a typical qualified individual working in the area. FAQC-FireProtection-2007.docx Description Fire Protection Qualification Card - 2007 FAQC-FireProtection-2000.docx Description Fire Protection Qualification Card - 2000

31

Resistance after firing protected electric match  

SciTech Connect

An electric match having electrical leads embedded in flame-producing compound is protected against an accidental resistance across the leads after firing by a length of heat-shrinkable tubing encircling the match body and having a skirt portion extending beyond the leads. The heat of the burning match and an adjacent thermal battery causes the tubing to fold over the end of the match body, covering the ends of the leads and protecting them from molten pieces of the battery.

Montoya, Arsenio P. (Albuquerque, NM)

1981-11-10T23:59:59.000Z

32

November 27, 2006 UNDERGROUND WATER LINES FOR DOMESTIC AND FIRE PROTECTION SYSTEMS  

E-Print Network (OSTI)

, guidelines and specifications. B. The following codes, as required by law: 1. ANSI/NFPA-70, National Electric.2 COPPER A. Wall-mounted 110-blocks (for voice applications) 1. Performance shall meet the performance 5e 110 Block Kits b) Panduit Pan-Punch 110 category 5e System Kits B. Angled patch panels 1. Size

33

Surveillance Guide - FPS 12.2 Fire Protection and Prevention  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FIRE PROTECTION AND PREVENTION FIRE PROTECTION AND PREVENTION 1.0 Objective The objective of this surveillance is to ensure that the contractor is implementing an effective program to minimize the potential for fires that could threaten the health and safety of the public or DOE's workers, or produce significant losses. In addition, the surveillance examines the effectiveness of steps taken to mitigate any fires that might occur. Finally, the surveillance provides an opportunity to evaluate compliance with requirements and standards for fire prevention and mitigation established by DOE. 2.0 References DOE 5480.7A, Fire Protection (or DOE O 420.1, Facility Safety) RLID 5480.7, Fire Protection (or RLID 420.1, Fire Protection) 29 CFR 1910 29 CFR 1926 DOE-HDBK-1062-96, "DOE Fire Protection Handbook (See this as well as other

34

DOE Fire Protection Handbook, Volume I  

Science Conference Proceedings (OSTI)

The Department of Energy (DOE) Fire Protection Program is delineated in a number of source documents including; the Code of Federal Regulations (CFR), DOE Policy Statements and Orders, DOE and national consensus standards (such as those promulgated by the National Fire Protection Association), and supplementary guidance, This Handbook is intended to bring together in one location as much of this material as possible to facilitate understanding and ease of use. The applicability of any of these directives to individual Maintenance and Operating Contractors or to given facilities and operations is governed by existing contracts. Questions regarding applicability should be directed to the DOE Authority Having Jurisdiction for fire safety. The information provided within includes copies of those DOE directives that are directly applicable to the implementation of a comprehensive fire protection program. They are delineated in the Table of Contents. The items marked with an asterisk (*) are included on the disks in WordPerfect 5.1 format, with the filename noted below. The items marked with double asterisks are provided as hard copies as well as on the disk. For those using MAC disks, the files are in Wordperfect 2.1 for MAC.

NONE

1996-08-01T23:59:59.000Z

35

Electronic firing systems and methods for firing a device ...  

An electronic firing system comprising a control system, a charging system, an electrical energy storage device, a shock tube firing circuit, a shock tube connector ...

36

Optimization of Fire Protection Impairments at Nuclear Power Plants  

Science Conference Proceedings (OSTI)

In recent years, risk-informed and performance-based (RI/PB) fire protection is gaining further acceptance by the Nuclear Regulatory Commission (NRC) and the industry. In addition, fire risk assessment methods are gaining some level of maturity since the first industrywide experience with individual plant examination for external events (IPEEE). RI/PB methods can reduce the cost of operating fire protection programs and maintaining fire safety.

2006-08-07T23:59:59.000Z

37

Electronic firing systems and methods for firing a device  

SciTech Connect

An electronic firing system comprising a control system, a charging system, an electrical energy storage device, a shock tube firing circuit, a shock tube connector, a blasting cap firing circuit, and a blasting cap connector. The control system controls the charging system, which charges the electrical energy storage device. The control system also controls the shock tube firing circuit and the blasting cap firing circuit. When desired, the control system signals the shock tube firing circuit or blasting cap firing circuit to electrically connect the electrical energy storage device to the shock tube connector or the blasting cap connector respectively.

Frickey, Steven J. (Boise, ID); Svoboda, John M. (Idaho Falls, ID)

2012-04-24T23:59:59.000Z

38

Savannah River Site Fire Protection engineers work in the community...  

National Nuclear Security Administration (NNSA)

work in the community Posted By Office of Public Affairs Members of the Savannah River Tritium Enterprise's Fire Protection department have taken their expertise out into the local...

39

Corrosion protection pays off for coal-fired power plants  

Science Conference Proceedings (OSTI)

Zinc has long been used to hot-dip galvanise steel to deliver protection in harsh environments. Powder River Basin or eastern coal-fired plants benefit from using galvanized steel for conveyors, vibratory feeders, coal hoppers, chutes, etc. because maintenance costs are essentially eliminated. When life cycle costs for this process are compared to an alternative three-coal paint system for corrosion protection, the latter costs 5-10 times more than hot-dip galvanizing. An AEP Power Plant in San Juan, Puerto Rico and the McDuffie Coal Terminal in Mobile, AL, USA have both used hot-dip galvanized steel. 1 fig., 1 tab.

Hansen, T.

2006-11-15T23:59:59.000Z

40

CRAD, Fire Protection - Los Alamos National Laboratory Waste  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection - Los Alamos National Laboratory Waste Fire Protection - Los Alamos National Laboratory Waste Characterization, Reduction, and Repackaging Facility CRAD, Fire Protection - Los Alamos National Laboratory Waste Characterization, Reduction, and Repackaging Facility A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for an assessment of the Fire Protection Program portion of an Operational Readiness Review at the Los Alamos National Laboratory Waste Characterization, Reduction, and Repackaging Facility. CRADs provide a recommended approach and the types of information to gather to assess elements of a DOE contractor's programs. CRAD, Fire Protection - Los Alamos National Laboratory Waste

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

CRAD, Fire Protection - Idaho Accelerated Retrieval Project Phase II |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection - Idaho Accelerated Retrieval Project Phase Fire Protection - Idaho Accelerated Retrieval Project Phase II CRAD, Fire Protection - Idaho Accelerated Retrieval Project Phase II February 2006 A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a February 2006 Commencement of Operations assessment of the Fire Protection program at the Idaho National Laboratory, Idaho Accelerated Retrieval Project Phase II. CRADs provide a recommended approach and the types of information to gather to assess elements of a DOE contractor's programs. CRAD, Fire Protection - Idaho Accelerated Retrieval Project Phase II More Documents & Publications CRAD, Engineering - Idaho Accelerated Retrieval Project Phase II

42

CRAD, Fire Protection - Oak Ridge National Laboratory High Flux Isotope  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection - Oak Ridge National Laboratory High Flux Fire Protection - Oak Ridge National Laboratory High Flux Isotope Reactor CRAD, Fire Protection - Oak Ridge National Laboratory High Flux Isotope Reactor February 2006 A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a February 2006 Commencement of Operations assessment of the Fire Protection program at the Idaho National Laboratory, Idaho Accelerated Retrieval Project Phase II. CRADs provide a recommended approach and the types of information to gather to assess elements of a DOE contractor's programs. CRAD, Fire Protection - Oak Ridge National Laboratory High Flux Isotope Reactor More Documents & Publications

43

Savannah River Site Waste Solidification Building Corrective Actions from the January 2013 Report on Construction Quality of Mechanical Systems Installation and Fire Protection Design, May 2013  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HIAR SRS-2013-5-07 HIAR SRS-2013-5-07 Site: Savannah River Site Subject: Office of Enforcement and Oversight's Office of Safety and Emergency Management Evaluations Activity Report for the Savannah River Site (SRS) Waste Solidification Building (WSB) Corrective Actions from the January 2013 Report on Construction Quality of Mechanical Systems Installation and Fire Protection Design Dates of Activity : 05/07/2013 - 05/09/2013 Report Preparer: Joseph Lenahan Activity Description/Purpose: 1. Review the corrective actions being implemented by the construction contractor to address Findings 1-4, 6, and 9 from a construction quality review performed by the Office of Health, Safety and Security (HSS) (Reference 1). 2. Meet with the SRS WSB project staff and Savannah River Nuclear Solutions (SRNS) engineers to discuss the

44

Savannah River Site Waste Solidification Building Corrective Actions from the January 2013 Report on Construction Quality of Mechanical Systems Installation and Fire Protection Design, May 2013  

NLE Websites -- All DOE Office Websites (Extended Search)

HIAR SRS-2013-5-07 HIAR SRS-2013-5-07 Site: Savannah River Site Subject: Office of Enforcement and Oversight's Office of Safety and Emergency Management Evaluations Activity Report for the Savannah River Site (SRS) Waste Solidification Building (WSB) Corrective Actions from the January 2013 Report on Construction Quality of Mechanical Systems Installation and Fire Protection Design Dates of Activity : 05/07/2013 - 05/09/2013 Report Preparer: Joseph Lenahan Activity Description/Purpose: 1. Review the corrective actions being implemented by the construction contractor to address Findings 1-4, 6, and 9 from a construction quality review performed by the Office of Health, Safety and Security (HSS) (Reference 1). 2. Meet with the SRS WSB project staff and Savannah River Nuclear Solutions (SRNS) engineers to discuss the

45

Standards and Codes: Innovative Fire Protection  

Science Conference Proceedings (OSTI)

... as the key to minimizing the potential for US manufacturers to face ... and ASTM E05.17 developing standards for fire safety in passenger rail vehicles. ...

2011-11-17T23:59:59.000Z

46

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... information retrieval. Evolution of a United States Information System. National Fire Protection Association and International ...

47

Influence of safeguards and fire protection on criticality safety  

SciTech Connect

There are several positive influences of safeguards and fire protection on criticality safety. Experts in each discipline must be aware of regulations and requirements of the others and work together to ensure a fault-tree design. EG and G Idaho, Inc., routinely uses an Occupancy-Use Readiness Manual to consider all aspects of criticality safety, fire protection, and safeguards. The use of the analytical tree is described.

Six, D.E.

1980-01-01T23:59:59.000Z

48

Summary of Fire Protection Programs for Calendar Year 2007  

NLE Websites -- All DOE Office Websites (Extended Search)

SUMMARY of SUMMARY of FIRE PROTECTION PROGRAMS for CALENDAR YEAR 2007 UNITED STATES DEPARTMENT OF ENERGY Office of Corporate Safety Analysis Office of Nuclear Safety Policy and Assistance February 2009 Fire Protection Summary for Calendar Year 2007 i ii i FOREWORD A key safety objective of the U. S. Department of Energy (DOE) is to minimize the potential for and consequences of fires at DOE facilities. Since May 1950, an annual Fire Protection Program Summary (Annual Summary) has been developed by DOE and its predecessor agencies, the Atomic Energy Commission and the Energy Research Development Administration, to provide a means for measuring how well DOE is meeting this objective and where improvements can be made. In 1999, the Annual Summary reporting process was automated to streamline data collection and

49

Fire Suppression System Performance of Alternative Agents in ...  

Science Conference Proceedings (OSTI)

... development on nacelle fire protection followed, Klein (1950a) reported the results of the Jet Engine Fire Protection Program of the US Air Force. ...

1996-08-14T23:59:59.000Z

50

Fire protection considerations for the design and operation of liquefied petroleum gas (LPG) storage facilities  

SciTech Connect

This standard addresses the design, operation, and maintenance of LPG storage facilities from the standpoint of prevention and control of releases, fire-protection design, and fire-control measures, as well as the history of LPG storage facility failure, facility design philosophy, operating and maintenance procedures, and various fire-protection and firefighting approaches and presentations. The storage facilities covered are LPG installations (storage vessels and associated loading/unloading/transfer systems) at marine and pipeline terminals, natural gas processing plants, refineries, petrochemical plants, and tank farms.

1989-01-01T23:59:59.000Z

51

Fire Protection: EHS0020 Issue Date: October 13, 1997  

E-Print Network (OSTI)

An effective, comprehensive Fire Protection Program is essential to protect the campus community from injuries facilities, facility alterations/remodels, operations, apparatus, equipment and hazardous materials within-safety codes, laws and regulations on campus, and UC Santa Cruz­administered facilities. The DCFM is authorized

California at Santa Cruz, University of

52

BARRIER SYSTEM FULL SCALE FIRE TESTING ADDRESSEES  

E-Print Network (OSTI)

All holders of operating licenses for nuclear power reactors, except those who have permanently ceased operations and have certified that fuel has been permanently removed from the reactor vessel, and fuel facilities licensees. PURPOSE The U.S. Nuclear Regulatory Commission (NRC) is issuing this information notice (IN) to inform addressees of the results of Hemyc electrical raceway fire barrier system (ERFBS) full-scale fire tests. The Hemyc ERFBS did not perform for one hour as designed because shrinkage of the Hemyc ERFBS occurred during the testing. It is expected that recipients will review the information for applicability to their facilities and consider actions as appropriate to avoid similar problems. However, suggestions contained in this information notice are not NRC requirements; therefore, no specific action or written response is required. BACKGROUND The Hemyc ERFBS, manufactured by Promatec, Inc., has been installed at nuclear power plants (NPPs) to protect circuits in accordance with regulatory requirements (Reference 1) and plant-specific commitments. As a result of fire protection inspections, unresolved items (URIs) were opened at some nuclear power stations due to questions raised regarding the fire resistance capability of the Hemyc ERFBS (Reference 2). The Office of Nuclear Reactor Regulation (NRR) performed a review of the Hemyc ERFBS (Reference 3) and requested the NRC’s Office of Nuclear Regulatory Research (RES) to perform confirmatory testing of this ERFBS. RES performed the testing at the Omega Point Laboratories in Elmendorf, Texas. DISCUSSION This information notice describes the results of the investigation of the fire resistance capability of the Hemyc ERFBS (Attachment 1). The NRC performed two ASTM E 119 furnace tests on a number of cable raceway types that are protected by the Hemyc ERFBS (with and without air gaps) in accordance with the Hemyc ERFBS test plan (see ADAMS Accession No. ML043210141 for a preliminary version of the test plan). The test plan provides ML050890089 IN 2005-07

unknown authors

2005-01-01T23:59:59.000Z

53

DOE-STD-1066-99; Fire Protection Design Criteria  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6-99 6-99 July 1999 Superseding DOE-STD-1066-97 DOE STANDARD FIRE PROTECTION DESIGN CRITERIA U.S. Department of Energy AREA FIRP Washington, D.C. 20585 DISTRIBUTION STATEMENT. Approved for public release; distribution is unlimited. This document has been reproduced from the best available copy. Available to DOE and DOE contractors from ES&H Technical Information Services, U.S. Department of Energy, (800) 473-4375, fax: (301) 903-9823. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 605-6000. DOE-STD-1066-99 iii FOREWORD This Department of Energy (DOE) Standard is approved for use by all DOE elements and their contractors. DOE Standards are part of the DOE Directives System and are issued to provide supplemental

54

Resistance after firing protected electric match. [Patent application  

DOE Patents (OSTI)

An electric match having electrical leads embedded in flame-producing compound is protected against an accidental resistance across the leads after firing by a length of heat-shrinkable tubing encircling the match body and having a skirt portion extending beyond the leads. The heat of the burning match and an adjacent thermal battery causes the tubing to fold over the end of the match body, covering the ends of the leads and protecting them from molten pieces of the battery.

Montoya, A.P.

1980-03-20T23:59:59.000Z

55

Fire Protection Equipment Surveillance Optimization and Maintenance Guide  

Science Conference Proceedings (OSTI)

Performance-based analysis methods are finding widespread application in many industries, including the nuclear power industry, and in many areas, including design, maintenance, and operations. Fire protection surveillance tests and inspections are well suited for performance-based analysis and trending, so transitioning to a performance-based program is achievable and cost-effective for nuclear power plants.

2003-07-18T23:59:59.000Z

56

Excerpts from Introduction to Employee Fire and Life Safety 1 2001 National Fire Protection Association EMPLOYEE FIRE AND LIFE SAFETY  

E-Print Network (OSTI)

110 home power 99 / february & march 2004 code corner Common Mistakes & How to Avoid Them John Handbook are available from the National Fire Protection Association (NFPA), 11 Tracy Dr., Avon, MA 02322 · 800-344-3555 or 508-895-8300 · Fax: 800-593-6372 or 508-895-8301 · custserv@nfpa.org · www.nfpa

Alabama in Huntsville, University of

57

Y-12 Fire Protection Operations has new chief | Y-12 National Security  

NLE Websites -- All DOE Office Websites (Extended Search)

Fire Protection ... Fire Protection ... Y-12 Fire Protection Operations has new chief Posted: July 25, 2012 - 3:45pm J. Scott Vowell was recently appointed chief of Fire Protection Operations at the Y-12 National Security Complex. Vowell joined the Y-12 staff in 1993. Prior to being appointed fire chief, he served as assistant fire chief and fire captain. Previously he served as fire inspector at Oak Ridge National Laboratory. The Clinton native served on the Clinton City Emergency 911 Board from 1997 to 2001 and was a firefighter with the City of Clinton Fire Department for seven years. A division of Y-12's Safeguards, Security and Emergency Services, Fire Protection Operations has a roster of approximately 90, including firefighters, battalion chiefs and support staff. It provides emergency

58

GLOVEBOX WINDOWS, FIRE PROTECTION AND VOICES FROM THE PAST  

Science Conference Proceedings (OSTI)

'Study the past--what is past is prologue'. These words appear as the motto on a pair of statues at the National Archives Building in Washington DC. They are also the opening sentence in the preface of a document written in August of 1956 entitled 'A Summary of Accidents and Incidents Involving Radiation in Atomic Energy Activities--June 1945 thru December 1955'. This document, one of several written by D.F. Hayes of the Safety and Fire Protection Branch, Division of Organization and Personnel, U.S. Atomic Energy Commission in Washington DC, and many others are often forgotten even though they contain valuable glovebox fire protection lessons for us today.

Till, W

2009-04-15T23:59:59.000Z

59

Modern generator protection systems  

SciTech Connect

The special problems of the protection of generating stations with large machines connected to large integrated networks are presented. The coordination between the protective relays and tripping functions and the reliability of the protection scheme are important considerations in modern plants. Primary and backup protective functions, the applications, and their divisions into fault detection and ''fault prevention'' categories are considered. Testing and maintenance of the generator protection system including automatic calibration testing equipment is also discussed. The concept of the generator protection as a completely coordinated system and its realization with solid state protective relays is also presented. 9 refs.

Pencinger, C.J.

1981-01-01T23:59:59.000Z

60

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... diesel fuels; fire protection; sprinklers; fuel oils; inspection; storage tanks ... distribution systems (including all fuel oil tanks, pumps, generators, routing ...

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

FIRE PROTECTION DESIGN CONSIDERATIONS FOR WASTE-TO-ENERGY FACILITIES  

E-Print Network (OSTI)

. COOLING TOWERS Unless the cooling tower is constructed only of non combustible material, it should "Water Cooling Tower". For medium and large resource re covery facilities, the cooling tower system. For larger cooling towers, 20 min fire-resistant par titions that separate the cells would further minimize

Columbia University

62

LNG fire and vapor control system technologies  

SciTech Connect

This report provides a review of fire and vapor control practices used in the liquefied natural gas (LNG) industry. Specific objectives of this effort were to summarize the state-of-the-art of LNG fire and vapor control; define representative LNG facilities and their associated fire and vapor control systems; and develop an approach for a quantitative effectiveness evaluation of LNG fire and vapor control systems. In this report a brief summary of LNG physical properties is given. This is followed by a discussion of basic fire and vapor control design philosophy and detailed reviews of fire and vapor control practices. The operating characteristics and typical applications and application limitations of leak detectors, fire detectors, dikes, coatings, closed circuit television, communication systems, dry chemicals, water, high expansion foam, carbon dioxide and halogenated hydrocarbons are described. Summary descriptions of a representative LNG peakshaving facility and import terminal are included in this report together with typical fire and vapor control systems and their locations in these types of facilities. This state-of-the-art review identifies large differences in the application of fire and vapor control systems throughout the LNG industry.

Konzek, G.J.; Yasutake, K.M.; Franklin, A.L.

1982-06-01T23:59:59.000Z

63

Fire Protection Engineering Functional Area Qualification Standard, 2007  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

37-2007 37-2007 December 2007 Supersedes DOE-STD-1137-2000 July 2000 DOE STANDARD FIRE PROTECTION ENGINEERING FUNCTIONAL AREA QUALIFICATION STANDARD DOE Defense Nuclear Facilities Technical Personnel U.S. Department of Energy AREA TRNG Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. DOE-STD-1137-2007 ii Available on the Department of Energy Technical Standards Program Web Site at http://www.hss.energy.gov/nuclearsafety/techstds/ DOE-STD-1137-2007 iv INTENTIONALLY BLANK DOE-STD-1137-2007 v TABLE OF CONTENTS ACKNOWLEDGMENT ..................................................................................................VII PURPOSE.......................................................................................................................

64

Fire hazards evaluation for light duty utility arm system  

Science Conference Proceedings (OSTI)

In accordance with DOE Order 5480.7A, Fire Protection, a Fire Hazards Analysis must be performed for all new facilities. LMHC Fire Protection has reviewed and approved the significant documentation leading up to the LDUA operation. This includes, but is not limited to, development criteria and drawings, Engineering Task Plan, Quality Assurance Program Plan, and Safety Program Plan. LMHC has provided an appropriate level of fire protection for this activity as documented.

HUCKFELDT, R.A.

1999-02-24T23:59:59.000Z

65

Computer Measurement and Automation System for Gas-fired Heating...  

NLE Websites -- All DOE Office Websites (Extended Search)

Computer Measurement and Automation System for Gas-fired Heating Furnace Title Computer Measurement and Automation System for Gas-fired Heating Furnace Publication Type Journal...

66

Steam Plant Replaces Outdated Coal-Fired System | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Steam Plant Replaces Outdated Coal-Fired System Steam Plant Replaces Outdated Coal-Fired System September 1, 2012 - 12:00pm Addthis A new natural gas-fired steam plant will replace...

67

Fire Protection Engineering Functional Area Qualification Standard, 2000  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NOT MEASUREMENT SENSITIVE DOE-STD-1137-2000 July 2000 DOE STANDARD FIRE PROTECTION ENGINEERING FUNCTIONAL AREA QUALIFICATION STANDARD DOE Defense Nuclear Facilities Technical Personnel U.S. Department of Energy AREA TRNG Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced directly from the best available copy. Available to DOE and DOE contractors from ES&H Technical Information Services, U.S. Department of Energy, (800) 473-4375, fax: (301) 903-9823. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 605-6000. DOE-STD-1137-2000 iii APPROVAL DOE-STD-1137-2000 iv INTENTIONALLY BLANK

68

Independent Oversight Review of the Fire Protection Program at Lawrence Livermore National Laboratory, September 2013  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fire Protection Program at Fire Protection Program at Lawrence Livermore National Laboratory May 2011 February 2013 September 2013 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U. S. Department of Energy Table of Contents 1.0 Purpose .................................................................................................................................................... 1 2.0 Background ............................................................................................................................................. 1 3.0 Scope ....................................................................................................................................................... 2

69

Independent Oversight Review of the Fire Protection Program at Lawrence Livermore National Laboratory, September 2013  

NLE Websites -- All DOE Office Websites (Extended Search)

Fire Protection Program at Fire Protection Program at Lawrence Livermore National Laboratory May 2011 February 2013 September 2013 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U. S. Department of Energy Table of Contents 1.0 Purpose .................................................................................................................................................... 1 2.0 Background ............................................................................................................................................. 1 3.0 Scope ....................................................................................................................................................... 2

70

LLNL Fire Protection Engineering Standard 5.8 Facility Survey Program  

SciTech Connect

This standard describes the LLNL Fire Protection Facility Survey Program. The purpose of this standard is to describe the type of facility surveys required to fulfill the requirements of DOE Order 420.1B, Facility Safety. Nothing in this standard is intended to prevent the development of a FHA using alternative approaches. Alternate approaches, including formatting, will be by exception only, and approved by the Fire Marshal/Fire Protection Engineering Subject Matter Expert in advance of their use.

Sharry, J A

2012-01-04T23:59:59.000Z

71

DOE Fire Protection Handbook, Volume II. Fire effects and electrical and electronic equipment  

SciTech Connect

Electrical and electronic equipment, including computers, are used at critical facilities throughout the Department of Energy (DOE). Hughes Associates, Inc. was tasked to evaluate the potential thermal and nonthermal effects of a fire on the electrical and electronic equipment and methods to analyze, evaluate, and assist in controlling the potential effects. This report is a result of a literature review and analysis on the effects of fire on electrical equipment. It is directed at three objectives: (1) Provide a state-of-the-art review and analysis of thermal and nonthermal damage to electrical and electronic equipment; (2) Develop a procedure for estimating thermal and nonthermal damage considerations using current knowledge; and (3) Develop an R&D/T&E program to fill gaps in the current knowledge needed to further perfect the procedure. The literature review was performed utilizing existing electronic databases. Sources searched included scientific and engineering databases including Dialog, NTIS, SciSearch and NIST BFRL literature. Incorporated in the analysis is unpublished literature and conversations with members of the ASTM E-5.21, Smoke Corrosivity, and researchers in the electronics field. This report does not consider the effects of fire suppression systems or efforts. Further analysis of the potential impact is required in the future.

NONE

1994-08-18T23:59:59.000Z

72

Advancements in low NOx tangential firing systems  

Science Conference Proceedings (OSTI)

The most cost effective method of reducing nitrogen oxide emissions when burning fossil fuels, such as coal, is through in-furnace NOx reduction processes. ABB Combustion Engineering, Inc. (ABB CE), through its ABB Power Plant Laboratories has been involved in the development of such low NOx pulverized coal firing systems for many years. This development effort is most recently demonstrated through ABB CE`s involvement with the U.S. Department of Energy`s (DOE) {open_quotes}Engineering Development of Advanced Coal Fired Low-Emission Boiler Systems{close_quotes} (LEBS) project. The goal of the DOE LEBS project is to use {open_quotes}near term{close_quotes} technologies to produce a commercially viable, low emissions boiler. This paper addresses one of the key technologies within this project, the NOx control subsystem. The foundation for the work undertaken at ABB CE is the TFS 2000{trademark} firing system, which is currently offered on a commercial basis. This system encompasses sub-stoichiometric combustion in the main firing zone for reduced NOx formation. Potential enhancements to this firing system focus on optimizing the introduction of the air and fuel within the primary windbox to provide additional horizontal and vertical staging. As is the case with all in-furnace NOx control processes, it is necessary to operate the system in a manner which does not decrease NOx at the expense of reduced combustion efficiency.

Hein, R. von; Maney, C.; Borio, R. [and others

1996-12-31T23:59:59.000Z

73

CENTER FOR FIRE RESEARCH  

Science Conference Proceedings (OSTI)

... Expert System and Fire Protection Design Assessment System ... Tf - T ) is equivalent to a forced flow convection ... The local force balances in the z and ...

2008-11-21T23:59:59.000Z

74

Independent Oversight Review of the Fire Protection Program at...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PNSO Pacific Northwest Site Office POD Plan of the Day PSF Physical Sciences Facility R&D Research and Development RFD Richland Fire Department RPL Radiochemical Processing...

75

Fire Protection of Structural Steel in High-Rise Buildings  

Science Conference Proceedings (OSTI)

... for Structural Fire Safety Design and Retrofit of Structures ... products or gypsum with a light weight aggregate ... in both cost and time savings in design ...

2005-04-29T23:59:59.000Z

76

Geothermal system saving money at fire station | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Geothermal system saving money at fire station Geothermal system saving money at fire station April 9, 2010 - 3:45pm Addthis Joshua DeLung What will the project do? A geothermal...

77

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... of a Residential Heat Pump Operating in the Cooling Mode With ... to Fire Protection and Life Safety Systems of the World Trade Center Towers. ...

78

Free Online Tool Aids Decisions on Fire Sprinkler Systems for ...  

Science Conference Proceedings (OSTI)

Free Online Tool Aids Decisions on Fire Sprinkler Systems for Homes. From NIST Tech Beat: April 12, 2011. ...

2011-04-13T23:59:59.000Z

79

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Fire Protection Handbook, 20th Edition. ... fire suppression; water distribution; fire tests; design applications; performance evaluation; pipes; water mist ...

80

ADVANCED WORKER PROTECTION SYSTEM  

Science Conference Proceedings (OSTI)

From 1993 to 2000, OSS worked under a cost share contract from the Department of Energy (DOE) to develop an Advanced Worker Protection System (AWPS). The AWPS is a protective ensemble that provides the user with both breathing air and cooling for a NIOSH-rated duration of two hours. The ensemble consists of a liquid air based backpack, a Liquid Cooling Garment (LCG), and an outer protective garment. The AWPS project was divided into two phases. During Phase 1, OSS developed and tested a full-scale prototype AWPS. The testing showed that workers using the AWPS could work twice as long as workers using a standard SCBA. The testing also provided performance data on the AWPS in different environments that was used during Phase 2 to optimize the design. During Phase 1, OSS also performed a life-cycle cost analysis on a representative clean up effort. The analysis indicated that the AWPS could save the DOE millions of dollars on D and D activities and improve the health and safety of their workers. During Phase 2, OSS worked to optimize the AWPS design to increase system reliability, to improve system performance and comfort, and to reduce the backpack weight and manufacturing costs. To support this design effort, OSS developed and tested several different generations of prototype units. Two separate successful evaluations of the ensemble were performed by the International Union of Operation Engineers (IUOE). The results of these evaluations were used to drive the design. During Phase 2, OSS also pursued certifying the AWPS with the applicable government agencies. The initial intent during Phase 2 was to finalize the design and then to certify the system. OSS and Scott Health and Safety Products teamed to optimize the AWPS design and then certify the system with the National Institute of Occupational Health and Safety (NIOSH). Unfortunately, technical and programmatic difficulties prevented us from obtaining NIOSH certification. Despite the inability of NIOSH to certify the design, OSS was able to develop and successfully test, in both the lab and in the field, a prototype AWPS. They clearly demonstrated that a system which provides cooling can significantly increase worker productivity by extending the time they can function in a protective garment. They were also able to develop mature outer garment and LCG designs that provide considerable benefits over current protective equipment, such as self donning and doffing, better visibility, and machine washable. A thorough discussion of the activities performed during Phase 1 and Phase 2 is presented in the AWPS Final Report. The report also describes the current system design, outlines the steps needed to certify the AWPS, discusses the technical and programmatic issues that prevented the system from being certified, and presents conclusions and recommendations based upon the seven year effort.

Judson Hedgehock

2001-03-16T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Keywords: protective clothing; fire fighters; heat transfer; turnout coats; thermal insulation; fire research; computer models Abstract: ...

82

Understanding Corrosion Mechanisms in Oxy-Fired Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Understanding Corrosion Mechanisms Understanding Corrosion Mechanisms in Oxy-Fired Systems Background In Oxy-fired Systems, oxygen is used for combustion of coal rather than air. It produces flue (exhaust) gas with concentrated carbon dioxide (CO2), thus facilitating its capture and sequestration. An added benefit of oxy-firing is that it reduces or eliminates nitrogen oxide (NO X ) emissions. Additional energy is required with oxy-firing and subsequent carbon sequestration

83

Gas fired Advanced Turbine System  

SciTech Connect

The primary objective of the first phase of the Advanced Gas Turbine System (ATS) program was the concept definition of an advanced engine system that meets efficiency and emission goals far exceeding those that can be provided with today`s equipment. The thermal efficiency goal for such an advanced industrial engine was set at 50% some 15 percentage points higher than current equipment levels. Exhaust emissions goals for oxides of nitrogen (NO{sub x}), carbon monoxide (CO), and unburned hydrocarbons (UH) were fixed at 8 parts per million by volume (ppmv), 20 ppmv, and 20 ppmv respectively, corrected to 15% oxygen (O{sub 2}) levels. Other goals had to be addressed; these involved reducing the cost of power produced by 10 percent and improving or maintaining the reliability, availability, and maintainability (RAM) at current levels. This advanced gas turbine was to be fueled with natural gas, and it had to embody features that would allow it bum coal or coal derived fuels.

LeCren, R.T.; White, D.J.

1993-01-01T23:59:59.000Z

84

Adaptive protection algorithm and system  

Science Conference Proceedings (OSTI)

An adaptive protection algorithm and system for protecting electrical distribution systems traces the flow of power through a distribution system, assigns a value (or rank) to each circuit breaker in the system and then determines the appropriate trip set points based on the assigned rank.

Hedrick, Paul (Pittsburgh, PA); Toms, Helen L. (Irwin, PA); Miller, Roger M. (Mars, PA)

2009-04-28T23:59:59.000Z

85

Chemically reactive coatings for passive fire protection in LNG and LPG storage and transporation  

SciTech Connect

According to Van Dyke Associates and TSI Inc., supporting and containing steels used to store and transport LNG and LPG are best protected in case of fire by thermally reactive subliming compounds. When exposed to fire, such compounds undergo an endothermic reaction; thus the substrate material beneath the coating will not heat up beyond the temperature at which this reaction occurs. Gases released by the sublimation reaction pass outward through the pores of the char, breaking down further as they absorb more energy. Numerous tests confirm that in comparison with other types of coatings, subliming compounds require the smallest thickness of coating for any specified level of protection. Routine spraying application techniques further reduce the cost of this passive fire-protection method.

Van Dyke, B.H.; Kawaller, S.T.

1979-01-01T23:59:59.000Z

86

Oak Ridge Office Oversight of the Fire Protection Program at the Oak Ridge Reservation, August 2011  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Independent Review of the Independent Review of the Oak Ridge Office Oversight of the Fire Protection Program at the Oak Ridge Reservation May 2011 August 2011 Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy i Table of Contents 1.0 Purpose and Scope ............................................................................................................................... 1 2.0 Results ................................................................................................................................................... 1 3.0 Conclusions ........................................................................................................................................... 3

87

A Surface Protective System  

SciTech Connect

Part of the design and development work connected with the erection of the chemistry "cave" in the "GP" Building entailed an investigation of various protective measures for materials of construction. This work was based on the observations and recommendations of personnel engaged in work at a similar installation at Argonne National Laboratory.

Brown, W. T.

1950-11-01T23:59:59.000Z

88

Cathodic protection diagnostic expert system  

Science Conference Proceedings (OSTI)

A knowledge-based diagnostic system has been developed for troubleshooting cathodic protection systems. The expert system is designed to work in conjunction with a database that stores inventory and field measurement information and flags problem areas. The system is described, and examples of troubleshooting using the system are presented.

Van Blaricum, V.L.; Kumar, A. (Army Construction Engineering Research Labs., Champaign, IL (United States)); Park, Y.T. (Soong Sil Univ., Seoul (Korea, Republic of). Dept. of Computer Science)

1994-12-01T23:59:59.000Z

89

An evaluation of the fire barrier system thermo-lag 330-1  

SciTech Connect

This report presents the results of three fire endurance tests and one ampacity derating test set of the fire barrier system Thermo-Lag 330-1 Subliming Coating. Each test was performed using cable tray specimens protected by a nominal three-hour fire barrier envelope comprised of two layers of nominal 1/2 inch thick material. The fire barrier systems for two of the three fire endurance test articles and for the ampacity derating test article were installed in accordance with the manufacturer`s installations procedures. The barrier system for the third fire endurance test article was a full reproduction of one of the original manufacturer`s qualification test articles. This final test article included certain installation enhancements not considered typical of current nuclear power plant installations. The primary criteria for fire endurance performance evaluation was based on cable circuit integrity testing. Secondary consideration was also given to the temperature rise limits set forth in the ASTM E119 standard fire barrier test procedure. All three of the fire endurance specimens failed prematurely. Circuit integrity failures for the two fire endurance test articles with procedures-based installations were recorded at approximately 76 and 59 minutes into the exposures for a 6 inch wide and 12 inch wide cable tray respectively. Temperature excursion failures (single point) for these two test articles were noted at approximately 65 and 56 minutes respectively. The first circuit integrity failure for the full reproduction test article was recorded approximately 119 minutes into the exposure, and the first temperature excursion failure for this test article was recorded approximately 110 minutes into the exposure.

Nowlen, S.P. [Sandia National Labs., Albuquerque, NM (United States). Components and Structures Safety and Reliability; Ross, S. [Science and Engineering Associates, Albuquerque, NM (United States)

1994-09-01T23:59:59.000Z

90

Geothermal system saving money at fire station | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Geothermal system saving money at fire station Geothermal system saving money at fire station Geothermal system saving money at fire station April 9, 2010 - 3:45pm Addthis Joshua DeLung What will the project do? A geothermal heating and cooling system has enabled the substation to save taxpayers $15,000 annually when compared to a traditional system. The high temperature of the treatment building's water helps reduce the amount of energy needed to heat water in the substation. An environmentally friendly geothermal heating and cooling system in Pennsylvania will save taxpayers $15,000 a year as part of a new fire substation that will decrease emergency response times. The Alpha Fire Co. celebrated the opening of substation on the ground floor of the College Township municipal building earlier this year in State

91

Fire Resistance Tests of Floor Truss Systems  

Science Conference Proceedings (OSTI)

... Trade Center Disaster: The Con Ed Substation in World ... 4.1.1 Span of Test Assembly ... The Underwriters Laboratories of Canada fire testing facility in ...

92

Fire Resistance Testing of WTC Floor System  

Science Conference Proceedings (OSTI)

... NYC Building Code Provisions (Fire Resistance in hours) ... [1] Letter dated October 30, 1969 from Robert J. Linn (Manager, Project Planning, The ...

2010-05-28T23:59:59.000Z

93

Fires  

Science Conference Proceedings (OSTI)

... In February of 2011, wildland fires outside of Amarillo, Texas destroyed 70 homes, burned more than 25,000 acres of land, and caused nearly $6 ...

2012-12-11T23:59:59.000Z

94

Oak Ridge Office Oversight of the Fire Protection Program at...  

NLE Websites -- All DOE Office Websites (Extended Search)

Having Jurisdiction BNA Baseline Needs Assessment CSE Cognizant System Engineer DOE U.S. Department of Energy EM DOE Office of Environmental Management ES&H Environment,...

95

Operational Awareness Rerview of a Department of Energy Richland Operations Office Fire Protection Surveillance, April 2013  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HIAR-RL-2013-04-08 HIAR-RL-2013-04-08 Site: DOE-Richland Operations Office Subject: Office of Enforcement and Oversight's Office of Safety and Emergency Management Evaluations Activity Report for the Department of Energy Richland Operations Office Fire Protection Surveillance Dates of Activity : 04/08/2013 - 04/11/2013 Report Preparer: Jake Wechselberger Activity Description/Purpose: The U.S. Department of Energy (DOE) Office of Enforcement and Oversight, within the Office of Health, Safety and Security (HSS), performed an onsite operational awareness review of a DOE Richland Operations Office (DOE-RL) fire protection surveillance. Result: During the period April 8-11, 2013, an HSS representative participated in DOE-RL tours of various site facilities to review

96

Operational Awareness Rerview of a Department of Energy Richland Operations Office Fire Protection Surveillance, April 2013  

NLE Websites -- All DOE Office Websites (Extended Search)

HIAR-RL-2013-04-08 HIAR-RL-2013-04-08 Site: DOE-Richland Operations Office Subject: Office of Enforcement and Oversight's Office of Safety and Emergency Management Evaluations Activity Report for the Department of Energy Richland Operations Office Fire Protection Surveillance Dates of Activity : 04/08/2013 - 04/11/2013 Report Preparer: Jake Wechselberger Activity Description/Purpose: The U.S. Department of Energy (DOE) Office of Enforcement and Oversight, within the Office of Health, Safety and Security (HSS), performed an onsite operational awareness review of a DOE Richland Operations Office (DOE-RL) fire protection surveillance. Result: During the period April 8-11, 2013, an HSS representative participated in DOE-RL tours of various site facilities to review

97

Reducing Operations and Maintenance Costs of Nuclear Power Plant Fire Protection Programs  

Science Conference Proceedings (OSTI)

This report discusses opportunities for utilities to reduce fire protection operations and maintenance (O&M) costs. A number of these opportunities have been implemented by some utilities and can be implemented now by others. Other opportunities can be implemented in the short term with some additional development. These other opportunities are amenable to cooperative projects with costs shared by multiple utilities. There is also a group of opportunities that are probably best developed on an industry w...

1997-01-08T23:59:59.000Z

98

PROTECTIVE CLOTHING MONITORING SYSTEM  

SciTech Connect

An automatic conveyor-type laundry monitoring system, whlch monitors laboratory coats and coveralls for both alpha and beta-gamma contamination, was developed and installed at the Hanford Laundry Facility to improve monitoring efficiency and control. The instrument employs eight alpha and seven beta-gamma scintillation large-area detectors, a garment conveyor, solid state circuitry, and appropriate signaling devices. Oarments are manually placed on hangers which are then placed onto an automatic loading mechanism. Each garment is conveyed past detectors where it is monitored for beta-gamma and alpha contamination. Contaminated garments are rejected and dropped into a special contniner if spot contamination exceeds 1000 disintegrations per minute (dis/min) of alpha or 5000 dis/min of mixed fission products. The garments which are not rejected pass through for folding and distribution. The system, which requires only one attendant, can effectively monitor 500 garments per standard shift. System operation was fully successful for ten months. (auth)

Rankin, M.O.; Spear, W.G.

1963-08-01T23:59:59.000Z

99

Fire  

NLE Websites -- All DOE Office Websites (Extended Search)

Fire Fire Nature Bulletin No. 51 Febraury 1, 1946 Forest Preserve District of Cook County Clayton F. Smith, President Roberts Mann, Superintendent of Conservation FIRE Most people firmly believe the ancient notion that the prairies and vacant lots should be burnt off "to make better grass." Many are doing so now. Boys who have seen their parents and neighbors kindling fires on vacant property frequently do likewise on the prairies. Recently there have been four fires in the forest preserves which spread from adjoining land. Burning does more harm than good. True, it gets rid of the old weed stalks and dried grass of last year, so that new grass shows green more quickly. But repeated burnings kill the good, nutritious grasses such as bluegrass, timothy and clover. The wildflowers disappear. All food and nesting cover for birds, rabbits and other wildlife is destroyed, just when they need it most. Thistles thrive. Only tough grasses of little value for pasture or hay, such as crabgrass and quackgrass, and the weeds survive.

100

FIRE HAZARDS ANALYSIS - BUSTED BUTTE  

SciTech Connect

The purpose of this fire hazards analysis (FHA) is to assess the risk from fire within individual fire areas at the Busted Butte Test Facility and to ascertain whether the DOE fire safety objectives are met. The objective, identified in DOE Order 420.1, Section 4.2, is to establish requirements for a comprehensive fire and related hazards protection program for facilities sufficient to minimize the potential for: (1) The occurrence of a fire related event. (2) A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees. (3) Vital DOE programs suffering unacceptable interruptions as a result of fire and related hazards. (4) Property losses from a fire and related events exceeding limits established by DOE. Critical process controls and safety class systems being damaged as a result of a fire and related events.

R. Longwell; J. Keifer; S. Goodin

2001-01-22T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Recommended practice for fire protection for electric generating plants and high voltage direct current converter stations. 2005 ed.  

Science Conference Proceedings (OSTI)

The standard outlines fire safety recommendations for gas, oil, coal, and alternative fuel electric generating plants including high voltage direct current converter stations and combustion turbine units greater than 7500 hp used for electric generation. Provisions apply to both new and existing plants. The document provides fire prevention and fire protection recommendations for the: safety of construction and operating personnel; physical integrity of plant components; and continuity of plant operations. The 2005 edition includes revisions and new art that clarify existing provisions. 5 annexes.

NONE

2005-07-01T23:59:59.000Z

102

A Comparison of Three Fire Models in the Simulation of Accidental Fires  

E-Print Network (OSTI)

R.L. , “Ceiling Jet Flows”, SFPE Handbook of Fire ProtectionJet Flames and Pool Fires”, SFPE Handbook of Fire ProtectionCompounds in Fires”, SFPE Handbook of Fire Protection

Rein, Guillermo; Bar-Ilan, Amnon; Fernandez-Pello, Carlos; Alvares, Norman

2004-01-01T23:59:59.000Z

103

Construction program for a large superconducting MHD magnet system at the coal-fired flow facility  

DOE Green Energy (OSTI)

The Argonne National Laboratory has designed and is constructing a 6 T large aperture superconducting MHD magnet for use in the Coal-Fired Flow Facility (CFFF) at the University of Tennessee Space Institute (UTSI) at Tullahoma, Tennessee. The magnet system consists of the superconducting magnet, a magnet power supply, an integrated instrumentation for operation, control and protection, and a complete cryogenic facility including a CTI Model 2800 helium refrigerator/liquefier with two compressors, helium gas handling system and a 7500 liter liquid helium dewar. The complete system will be tested at Argonne, IL in 1981. The magnet design is reviewed, and the coil fabrication programs are described in detail.

Wang, S.T.; Genens, L.; Gonczy, J.; Ludwig, H.; Lieberg, M.; Kraft, E.; Gacek, D.; Huang, Y.C.; Chen, C.J.

1980-01-01T23:59:59.000Z

104

An Unmanned Aircraft System for Automatic Forest Fire Monitoring and Measurement  

Science Conference Proceedings (OSTI)

The paper presents an Unmanned Aircraft System (UAS), consisting of several aerial vehicles and a central station, for forest fire monitoring. Fire monitoring is defined as the computation in real-time of the evolution of the fire front shape and potentially ... Keywords: Cooperative perception, Forest fire fighting, UAS

Luis Merino; Fernando Caballero; J. Ramiro Martínez-De-Dios; Iván Maza; Aníbal Ollero

2012-01-01T23:59:59.000Z

105

Understanding Corrosion Mechanisms in Oxy-Fired Systems  

SciTech Connect

Replacing air with oxygen in coal-fired boilers (i.e. oxy-firing) combined with flue gas recirculation is a leading strategy to concentrate CO{sub 2} and assist in carbon capture and sequestration. A significant area of concern is the fireside corrosion with oxy-firing due to the higher CO{sub 2} levels in the combustion gas and potentially higher SO{sub x} and H{sub 2}O levels. In order to investigate this complicated issue, laboratory experiments are being conducted with and without synthetic ash to assess the potential effect of oxy-firing on fireside corrosion rates. The initial results of this project focus on commercial and model Fe-base alloys at 600 C. Without ash, a 50%H{sub 2}O-50%(CO{sub 2}-0.15O{sub 2}) environment was the most aggressive condition, requiring higher Cr contents than 100% H{sub 2}O or Ar-50%CO{sub 2}. With the specimens covered in ash, several gas compositions were examined, including different levels of H{sub 2}O and SO{sub 2} to simulate various oxy-firing strategies. Results also are presented for several laser-clad coating compositions for protecting tubes. An additional task is examining the effect of environment on mechanical properties. Initial work studied Ni-base alloys in steam at 800 C and found little effect of steam on the creep rupture life of alloy 230 but a 35% decrease for alloy 740.

Pint, Bruce A [ORNL; Dryepondt, Sebastien N [ORNL; Zhang, Ying [Tennessee Technological University

2011-01-01T23:59:59.000Z

106

DOE-STD-1088-95; DOE Standard Fire Protection For Relocatable Structures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8-95 8-95 JUNE 1995 DOE STANDARD FIRE PROTECTION FOR RELOCATABLE STRUCTURES U.S. Department of Energy AREA GDRQ Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced directly from the best available copy. Available to DOE and DOE contractors from the Office of Scientific and Technical Information, P.O. Box 62, Oak Ridge, TN 37831; (615) 576-8401. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 487-4650. Order No. DE95014751 DOE-STD-1088-95 iii TABLE OF CONTENTS PARAGRAPH PAGE FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v 1. SCOPE . . . . . . . . . . . .

107

Feasibility and design of blast mitigation systems for naval applications using water mist fire suppression systems  

E-Print Network (OSTI)

The recent trend of using fine water mist systems to replace the legacy HALON- 1301 fire suppression systems warrants further study into other applications of the water mist systems. Preliminary research and investigation ...

Kitchenka, Julie A

2004-01-01T23:59:59.000Z

108

Applications of coatings in coal-fired energy systems  

SciTech Connect

Corrosion and erosion of metallic structural materials at elevated temperatures in complex multicomponent gas environments that include particulates are potential problems in many fossil energy systems, especially those using coal as a feedstock. The use of appropriate corrosion-resistant coatings on metallic components offers an avenue to minimize material degradation and extend component life. The purpose of this paper is to review the current status of coating performance in environments typical of pulverized-coal-fired boilers, coal gasification, fluidized-bed combustion, and gas turbines. The paper discusses the complexity of environments in different systems and the coating requirements for acceptable performance. Examples illustrate the morphology and corrosion/erosion performance of coating/structural alloy combinations exposed in some of these systems. La addition, future research and development needs are discussed for coating applications in several coal-fired systems.

Natesan, K.

1992-03-01T23:59:59.000Z

109

RIVER PROTECTION PROJECT SYSTEM PLAN  

SciTech Connect

The U.S. Department of Energy (DOE), Office of River Protection (ORP) manages the River Protection Project (RPP). The RPP mission is to retrieve and treat Hanford's tank waste and close the tank farms to protect the Columbia River. As a result, the ORP is responsible for the retrieval, treatment, and disposal of the approximately 57 million gallons of radioactive waste contained in the Hanford Site waste tanks and closure of all the tanks and associated facilities. The previous revision of the System Plan was issued in September 2003. ORP has approved a number of changes to the tank waste treatment strategy and plans since the last revision of this document, and additional changes are under consideration. The ORP has established contracts to implement this strategy to establish a basic capability to complete the overall mission. The current strategy for completion of the mission uses a number of interrelated activities. The ORP will reduce risk to the environment posed by tank wastes by: (1) Retrieving the waste from the single-shell tanks (SST) to double-shell tanks (DST) for treatment and disposal; (2) Constructing and operating the WTP, which will safely treat all of the high-level waste (HLW) and about half of the low-activity waste (LAW) contained in the tank farms, and maximizing its capability and capacity; (3) Developing and deploying supplemental treatment capability or a second WTP LAW Facility that can safely treat about half of the LAW contained in the tank farms; (4) Developing and deploying treatment and packaging capability for transuranic (TRU) tank waste for shipment to and disposal at the Waste Isolation Pilot Plant (WIPP); (5) Deploying interim storage capacity for the immobilized HLW and shipping that waste to Yucca Mountain for disposal; (6) Operating the Integrated Disposal Facility for the disposal of immobilized LAW, along with the associated secondary waste, (7) Closing the SST and DST tank farms, ancillary facilities, and al1 waste management and treatment facilities, (8) Developing and implementing technical solutions to mitigate the impact from substantial1y increased estimates of Na added during the pretreatment of the tank waste solids, This involves a combination of: (1) refining or modifying the flowsheet to reduce the required amount of additional sodium, (2) increasing the overall LAW vitrification capacity, (3) increasing the incorporation of sodium into the LAW glass, or (4) accepting an increase in mission duration, ORP has made and continues to make modifications to the WTP contract as needed to improve projected plant performance and address known or emerging risks, Key elements of the implementation of this strategy are included within the scope of the Tank Operations Contract, currently in procurement Since 2003, the ORP has conducted over 30 design oversight assessments of the Waste Treatment and Immobilization Plant (WTP). The estimated cost at completion has increased and the schedule for construction and commissioning of the WTP has extended, The DOE, Office of Environmental Management (EM), sanctioned a comprehensive review of the WTP flowsheet, focusing on throughput. In 2005, the TFC completed interim stabilization of the SSTs and as of March 2007, has completed the retrieval of seven selected SSTs. Demonstration of supplemental treatment technologies continues. The ongoing tank waste retrieval experience, progress with supplemental treatment technologies, and changes in WTP schedule led to the FY 2007 TFC baseline submittal in November 2006. The TFC baseline submittal was developed before the WTP schedule was fully understood and approved by ORP, and therefore reflects an earlier start date for the WTP facilities. This System Plan is aligned with the current WTP schedule with hot commissioning beginning in 2018 and full operations beginning in 2019. Major decisions regarding the use of supplemental treatment and the associated technology, the ultimate needed capacity, and its relationship to the WTP have not yet been finalized. This System Plan assumes that the outcome of

CERTA PJ

2008-07-10T23:59:59.000Z

110

RIVER PROTECTION PROJECT SYSTEM PLAN  

Science Conference Proceedings (OSTI)

The U.S. Department of Energy (DOE), Office of River Protection (ORP) manages the River Protection Project (RPP). The RPP mission is to retrieve and treat Hanford's tank waste and close the tank farms to protect the Columbia River. As a result, ORP is responsible for the retrieval, treatment, and disposal of approximately 57 million gallons 1 of radioactive waste contained in the Hanford Site waste tanks and closure2 of all the tanks and associated facilities. The previous revision of the System Plan was issued in May 2008. ORP has made a number of changes to the tank waste treatment strategy and plans since the last revision of this document, and additional changes are under consideration. ORP has contracts in place to implement the strategy for completion of the mission and establish the capability to complete the overall mission. The current strategl involves a number of interrelated activities. ORP will reduce risk to the environment posed by tank wastes by the following: (1) Retrieving the waste from the single-shell tanks (SST) to double-shell tanks (DST) and delivering the waste to the Waste Treatment and Immobilization Plant (WTP). (2) Constructing and operating the WTP, which will safely treat all of the high-level waste (HLW) fraction contained in the tank farms. About one-third of the low-activity waste (LAW) fraction separated from the HLW fraction in the WTP will be immobilized in the WTP LAW Vitrification Facility. (3) Developing and deploying supplemental treatment capability assumed to be a second LAW vitrification facility that can safely treat about two-thirds of the LAW contained in the tank farms. (4) Developing and deploying supplemental pretreatment capability currently assumed to be an Aluminum Removal Facility (ARF) using a lithium hydrotalcite process to mitigate sodium management issues. (5) Developing and deploying treatment and packaging capability for contact-handled transuranic (CH-TRU) tank waste for possible shipment to and disposal at the Waste Isolation Pilot Plant (WIPP) in New Mexico. (6) Deploying interim storage capacity for the immobilized high-level waste (IHLW) pending determination of the final disposal pathway. (7) Closing the SST and DST tank farms, ancillary facilities, and all associated waste management and treatment facilities. (8) Optimizing the overall mission by resolution of technical and programmatic uncertainties, configuring the tank farms to provide a steady, well-balanced feed to the WTP, and performing trade-offs of the required amount and type of supplemental treatment and of the amount of HLW glass versus LAW glass. ORP has made and continues to make modifications to the WTP contract as needed to improve projected plant performance and address known or emerging risks. Key elements needed to implement the strategy described above are included within the scope of the Tank Operations Contract (TOC). Interim stabilization of the SSTs was completed in March 2004. As of April 2009, retrieval of seven SSTs has been completed and retrieval of four additional SSTs has been completed to the limits of technology. Demonstration of supplemental LAW treatment technologies has stopped temporarily pending revision of mission need requirements. Award of a new contract for tank operations (TOC), the ongoing tank waste retrieval experience, HLW disposal issues, and uncertainties in waste feed delivery and waste treatment led to the revision of the Performance Measurement Baseline (PM B), which is currently under review prior to approval. 6 This System Plan is aligned with the current WTP schedule, with hot commissioning beginning in 2018, and full operations beginning in late 2019. Major decisions regarding the use of supplemental treatment and the associated technology, the ultimate needed capacity, and its relationship to the WTP have not yet been finalized. This System Plan assumes that the outcome of these decisions will be to provide a second LAW vitrification facility. No final implementation decisions regarding supplemental technology can be made until the Tank Closure and

CERTA PJ; KIRKBRIDE RA; HOHL TM; EMPEY PA; WELLS MN

2009-09-15T23:59:59.000Z

111

RIVER PROTECTION PROJECT SYSTEM PLAN  

SciTech Connect

The U.S. Department of Energy (DOE), Office of River Protection (ORP) manages the River Protection Project (RPP). The RPP mission is to retrieve and treat Hanford's tank waste and close the tank farms to protect the Columbia River. As a result, ORP is responsible for the retrieval, treatment, and disposal of approximately 57 million gallons 1 of radioactive waste contained in the Hanford Site waste tanks and closure2 of all the tanks and associated facilities. The previous revision of the System Plan was issued in May 2008. ORP has made a number of changes to the tank waste treatment strategy and plans since the last revision of this document, and additional changes are under consideration. ORP has contracts in place to implement the strategy for completion of the mission and establish the capability to complete the overall mission. The current strategl involves a number of interrelated activities. ORP will reduce risk to the environment posed by tank wastes by the following: (1) Retrieving the waste from the single-shell tanks (SST) to double-shell tanks (DST) and delivering the waste to the Waste Treatment and Immobilization Plant (WTP). (2) Constructing and operating the WTP, which will safely treat all of the high-level waste (HLW) fraction contained in the tank farms. About one-third of the low-activity waste (LAW) fraction separated from the HLW fraction in the WTP will be immobilized in the WTP LAW Vitrification Facility. (3) Developing and deploying supplemental treatment capability assumed to be a second LAW vitrification facility that can safely treat about two-thirds of the LAW contained in the tank farms. (4) Developing and deploying supplemental pretreatment capability currently assumed to be an Aluminum Removal Facility (ARF) using a lithium hydrotalcite process to mitigate sodium management issues. (5) Developing and deploying treatment and packaging capability for contact-handled transuranic (CH-TRU) tank waste for possible shipment to and disposal at the Waste Isolation Pilot Plant (WIPP) in New Mexico. (6) Deploying interim storage capacity for the immobilized high-level waste (IHLW) pending determination of the final disposal pathway. (7) Closing the SST and DST tank farms, ancillary facilities, and all associated waste management and treatment facilities. (8) Optimizing the overall mission by resolution of technical and programmatic uncertainties, configuring the tank farms to provide a steady, well-balanced feed to the WTP, and performing trade-offs of the required amount and type of supplemental treatment and of the amount of HLW glass versus LAW glass. ORP has made and continues to make modifications to the WTP contract as needed to improve projected plant performance and address known or emerging risks. Key elements needed to implement the strategy described above are included within the scope of the Tank Operations Contract (TOC). Interim stabilization of the SSTs was completed in March 2004. As of April 2009, retrieval of seven SSTs has been completed and retrieval of four additional SSTs has been completed to the limits of technology. Demonstration of supplemental LAW treatment technologies has stopped temporarily pending revision of mission need requirements. Award of a new contract for tank operations (TOC), the ongoing tank waste retrieval experience, HLW disposal issues, and uncertainties in waste feed delivery and waste treatment led to the revision of the Performance Measurement Baseline (PM B), which is currently under review prior to approval. 6 This System Plan is aligned with the current WTP schedule, with hot commissioning beginning in 2018, and full operations beginning in late 2019. Major decisions regarding the use of supplemental treatment and the associated technology, the ultimate needed capacity, and its relationship to the WTP have not yet been finalized. This System Plan assumes that the outcome of these decisions will be to provide a second LAW vitrification facility. No final implementation decisions regarding supplemental technology can be made until the Tank Closure and

CERTA PJ; KIRKBRIDE RA; HOHL TM; EMPEY PA; WELLS MN

2009-09-15T23:59:59.000Z

112

RIVER PROTECTION PROJECT SYSTEM PLAN  

SciTech Connect

The U.S. Department of Energy (DOE), Office of River Protection (ORP) manages the River Protection Project (RPP). The RPP mission is to retrieve and treat Hanford's tank waste and close the tank farms to protect the Columbia River. As a result, the ORP is responsible for the retrieval, treatment, and disposal of the approximately 57 million gallons of radioactive waste contained in the Hanford Site waste tanks and closure of all the tanks and associated facilities. The previous revision of the System Plan was issued in September 2003. ORP has approved a number of changes to the tank waste treatment strategy and plans since the last revision of this document, and additional changes are under consideration. The ORP has established contracts to implement this strategy to establish a basic capability to complete the overall mission. The current strategy for completion of the mission uses a number of interrelated activities. The ORP will reduce risk to the environment posed by tank wastes by: (1) Retrieving the waste from the single-shell tanks (SST) to double-shell tanks (DST) for treatment and disposal; (2) Constructing and operating the WTP, which will safely treat all of the high-level waste (HLW) and about half of the low-activity waste (LAW) contained in the tank farms, and maximizing its capability and capacity; (3) Developing and deploying supplemental treatment capability or a second WTP LAW Facility that can safely treat about half of the LAW contained in the tank farms; (4) Developing and deploying treatment and packaging capability for transuranic (TRU) tank waste for shipment to and disposal at the Waste Isolation Pilot Plant (WIPP); (5) Deploying interim storage capacity for the immobilized HLW and shipping that waste to Yucca Mountain for disposal; (6) Operating the Integrated Disposal Facility for the disposal of immobilized LAW, along with the associated secondary waste, (7) Closing the SST and DST tank farms, ancillary facilities, and al1 waste management and treatment facilities, (8) Developing and implementing technical solutions to mitigate the impact from substantial1y increased estimates of Na added during the pretreatment of the tank waste solids, This involves a combination of: (1) refining or modifying the flowsheet to reduce the required amount of additional sodium, (2) increasing the overall LAW vitrification capacity, (3) increasing the incorporation of sodium into the LAW glass, or (4) accepting an increase in mission duration, ORP has made and continues to make modifications to the WTP contract as needed to improve projected plant performance and address known or emerging risks, Key elements of the implementation of this strategy are included within the scope of the Tank Operations Contract, currently in procurement Since 2003, the ORP has conducted over 30 design oversight assessments of the Waste Treatment and Immobilization Plant (WTP). The estimated cost at completion has increased and the schedule for construction and commissioning of the WTP has extended, The DOE, Office of Environmental Management (EM), sanctioned a comprehensive review of the WTP flowsheet, focusing on throughput. In 2005, the TFC completed interim stabilization of the SSTs and as of March 2007, has completed the retrieval of seven selected SSTs. Demonstration of supplemental treatment technologies continues. The ongoing tank waste retrieval experience, progress with supplemental treatment technologies, and changes in WTP schedule led to the FY 2007 TFC baseline submittal in November 2006. The TFC baseline submittal was developed before the WTP schedule was fully understood and approved by ORP, and therefore reflects an earlier start date for the WTP facilities. This System Plan is aligned with the current WTP schedule with hot commissioning beginning in 2018 and full operations beginning in 2019. Major decisions regarding the use of supplemental treatment and the associated technology, the ultimate needed capacity, and its relationship to the WTP have not yet been finalized. This System Plan assumes that the outcom

CERTA PJ

2008-07-10T23:59:59.000Z

113

Transition Process Pilot Report—NEI 04-02 Guidance for Implementing a Risk-Informed, Performance-Based Fire Protection Program Under 10 CFR 50.48(c)  

Science Conference Proceedings (OSTI)

Nuclear Energy Institute (NEI) document 04-02, "Guidance for Implementing a Risk-Informed, Performance-Based Fire Protection Program Under 10 CFR 50.48(c)," is under development to provide implementing guidance for a new fire protection licensing basis based upon National Fire Protection Association (NFPA) 805, "Performance-Based Standard for Fire Protection for Light Water Reactor Generating Plants." This report documents two pilot projects that tested this guidance.

2004-07-14T23:59:59.000Z

114

Interim Guidelines for Protecting Fire-Fighting Personnel From Multiple Hazards at Nuclear Plant Sites  

Science Conference Proceedings (OSTI)

Fire fighters and other emergency response personnel may encounter radiation, heat stress, or trauma when fighting fires in nuclear power plants. Recommendations contained in this report can be effective in reducing the impact of these hazards on fire brigade safety and performance.

1989-07-28T23:59:59.000Z

115

December 18, 2007 INTELLIGENT FIRE ALARM SYSTEM  

E-Print Network (OSTI)

with a capacity of 110 gallons or less. o Emergency spill or overflow containment UST system that is expeditiously permits may also contain site- specific requirements and references to other applicable NFPA codes and/or standards. Examples of commonly cited NFPA requirements include: o Availability of emergency shut-off valves

116

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Kawada, G. Fire Dynamics Simulator: User's Manual. ... 2; NFPA FPH2008;Fire Protection Handbook, 20th Edition ... Flow of Alternative Agents in Piping. ...

117

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... nuclear power plants; verification; validation; fire models; fire protection engineering ... in support of day-to-day nuclear power plant (NPP) applications ...

118

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Passive fire protection needs to be evaluated for its ability to contain a fire ... For instance, a hospital may be a safe housing shelter for able-bodied ...

119

Definition: Special Protection System | Open Energy Information  

Open Energy Info (EERE)

Protection System Protection System Jump to: navigation, search Dictionary.png Special Protection System An automatic protection system designed to detect abnormal or predetermined system conditions, and take corrective actions other than and/or in addition to the isolation of faulted components to maintain system reliability. Such action may include changes in demand, generation (MW and Mvar), or system configuration to maintain system stability, acceptable voltage, or power flows. An SPS does not include (a) underfrequency or undervoltage load shedding or (b) fault conditions that must be isolated or (c) out-of-step relaying (not designed as an integral part of an SPS). Also called Remedial Action Scheme.[1] Also Known As Remedial Action Scheme Related Terms system References

120

Slag processing system for direct coal-fired gas turbines  

SciTech Connect

Direct coal-fired gas turbine systems and methods for their operation are provided by this invention. The systems include a primary combustion compartment coupled to an impact separator for removing molten slag from hot combustion gases. Quenching means are provided for solidifying the molten slag removed by the impact separator, and processing means are provided forming a slurry from the solidified slag for facilitating removal of the solidified slag from the system. The released hot combustion gases, substantially free of molten slag, are then ducted to a lean combustion compartment and then to an expander section of a gas turbine.

Pillsbury, Paul W. (Winter Springs, FL)

1990-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Water augmented indirectly-fired gas turbine systems and method  

SciTech Connect

An indirectly-fired gas turbine system utilizing water augmentation for increasing the net efficiency and power output of the system is described. Water injected into the compressor discharge stream evaporatively cools the air to provide a higher driving temperature difference across a high temperature air heater which is used to indirectly heat the water-containing air to a turbine inlet temperature of greater than about 1,000.degree. C. By providing a lower air heater hot side outlet temperature, heat rejection in the air heater is reduced to increase the heat recovery in the air heater and thereby increase the overall cycle efficiency.

Bechtel, Thomas F. (Lebanon, PA); Parsons, Jr., Edward J. (Morgantown, WV)

1992-01-01T23:59:59.000Z

122

Water augmented indirectly-fired gas turbine system and method  

DOE Patents (OSTI)

An indirectly-fired gas turbine system utilizing water augmentation for increasing the net efficiency and power output of the system is described. Water injected into the compressor discharge stream evaporatively cools the air to provide a high driving temperature difference across a high temperature air heater which is used to indirectly heat the water-containing air to a turbine inlet temperature of greater than about 1000{degrees}C. By providing a lower air heater hot side outlet temperature, heat rejection in the air heater is reduced to increase the heat recovery in the air heater and thereby increase the overall cycle efficiency.

Bechtel, T.F.; Parsons, E.J. Jr.

1991-12-31T23:59:59.000Z

123

Water augmented indirectly-fired gas turbine system and method  

DOE Patents (OSTI)

An indirectly-fired gas turbine system utilizing water augmentation for increasing the net efficiency and power output of the system is described. Water injected into the compressor discharge stream evaporatively cools the air to provide a high driving temperature difference across a high temperature air heater which is used to indirectly heat the water-containing air to a turbine inlet temperature of greater than about 1000[degrees]C. By providing a lower air heater hot side outlet temperature, heat rejection in the air heater is reduced to increase the heat recovery in the air heater and thereby increase the overall cycle efficiency.

Bechtel, T.F.; Parsons, E.J. Jr.

1991-01-01T23:59:59.000Z

124

Voice Communication Systems Compatible With Respiratory Protection  

Science Conference Proceedings (OSTI)

Operating a nuclear power plant requires reliable voice communication among workers and supervisors. In hazardous situations where respiratory protection devices are necessary, improved voice communication can increase worker productivity and decrease radiation exposure. This report provides guidelines for the selection, use, and maintenance of voice communication systems that are compatible with respiratory protection.

1989-11-10T23:59:59.000Z

125

The protection of computer and electronic systems against ...  

Science Conference Proceedings (OSTI)

... the above flgurt, It should remain safe (no fires ... the indirect effects of lightning and power system faults ... a curative effort - learning to live and survive ...

2013-05-17T23:59:59.000Z

126

Heat pipe technology for coal-fired power systems  

SciTech Connect

This report summarizes the results of heat pipe R and D activities at Argonne National Laboratory (ANL) during the 1977 to 1984 time period. The heat pipe development efforts were associated with a variety of DOE supported projects involving coal-fired prime movers for stationary power generation. The role of heat pipes for these power systems is in their potential application as thermal transport systems for integrating fluidized bed combustors (FBC) with prime movers ranging from Stirling engines in total energy systems (approx.10 MWe) to closed-cycle gas turbines in central power plants (approx.1000 MWe). The results of initial investigations at ANL demonstrated that high-temperature sodium heat pipes provided the best heat exchanger technology for integrating Stirling engines with coal-fired FBC systems. A major accomplishment included the development and validation of a computer code (ANL/HTP) which calculates heat pipe operating limits and other significant characteristics necessary for power plant design. A number of developmental and prototype heat pipes were designed and fabricated through a subcontract effort with Thermacore, Inc., and delivered to ANL for performance testing. Preliminary test results from ANL's Heat Pipe Test Facility, using induction heating and a gas-water calorimeter to establish energy balances, are given in the report. Test data obtained to date are consistent with ANL/HTP code predictions. 47 refs., 53 figs., 22 tabs.

Uherka, K.L.; Holtz, R.E.; McLennan, G.A.; Koehl, E.R.

1985-04-01T23:59:59.000Z

127

Coal-fired high performance power generating system. Final report  

SciTech Connect

As a result of the investigations carried out during Phase 1 of the Engineering Development of Coal-Fired High-Performance Power Generation Systems (Combustion 2000), the UTRC-led Combustion 2000 Team is recommending the development of an advanced high performance power generation system (HIPPS) whose high efficiency and minimal pollutant emissions will enable the US to use its abundant coal resources to satisfy current and future demand for electric power. The high efficiency of the power plant, which is the key to minimizing the environmental impact of coal, can only be achieved using a modern gas turbine system. Minimization of emissions can be achieved by combustor design, and advanced air pollution control devices. The commercial plant design described herein is a combined cycle using either a frame-type gas turbine or an intercooled aeroderivative with clean air as the working fluid. The air is heated by a coal-fired high temperature advanced furnace (HITAF). The best performance from the cycle is achieved by using a modern aeroderivative gas turbine, such as the intercooled FT4000. A simplified schematic is shown. In the UTRC HIPPS, the conversion efficiency for the heavy frame gas turbine version will be 47.4% (HHV) compared to the approximately 35% that is achieved in conventional coal-fired plants. This cycle is based on a gas turbine operating at turbine inlet temperatures approaching 2,500 F. Using an aeroderivative type gas turbine, efficiencies of over 49% could be realized in advanced cycle configuration (Humid Air Turbine, or HAT). Performance of these power plants is given in a table.

1995-08-31T23:59:59.000Z

128

Performance control strategies for oil-fired residential heating systems  

SciTech Connect

Results are reported of a study of control system options which can be used to improve the combustion performance of residential, oil-fired heating equipment. Two basic control modes were considered in this program. The first is service required'' signals in which an indication is provided when the flame quality or heat exchanger cleanliness have degraded to the point that a service call is required. The second control mode is excess-air trim'' in which the burner would essentially tune itself continuously for maximum efficiency. 35 refs., 67 figs., 2 tabs.

Butcher, T.

1990-07-01T23:59:59.000Z

129

Slag processing system for direct coal-fired gas turbines  

SciTech Connect

Direct coal-fired gas turbine systems and methods for their operation are provided by this invention. The gas turbine system includes a primary zone for burning coal in the presence of compressed air to produce hot combustion gases and debris, such as molten slag. The turbine system further includes a secondary combustion zone for the lean combustion of the hot combustion gases. The operation of the system is improved by the addition of a cyclone separator for removing debris from the hot combustion gases. The cyclone separator is disposed between the primary and secondary combustion zones and is in pressurized communication with these zones. In a novel aspect of the invention, the cyclone separator includes an integrally disposed impact separator for at least separating a portion of the molten slag from the hot combustion gases.

Pillsbury, Paul W. (Winter Springs, FL)

1990-01-01T23:59:59.000Z

130

Review of the Savannah River Site, Waste Solidification Building, Construction Quality of Mechanical Systems Installation and Selected Aspects of Firre Protection System Design  

NLE Websites -- All DOE Office Websites (Extended Search)

the the Savannah River Site, Waste Solidification Building, Construction Quality of Mechanical Systems Installation and Selected Aspects of Fire Protection System Design January 2013 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy Independent Oversight Review of the Savannah River Site, Waste Solidification Building, Construction Quality of Mechanical Systems Installation and Selected Aspects of Fire Protection System Design Table of Contents 1.0 Purpose................................................................................................................................................. 1 2.0 Scope.................................................................................................................................................... 1

131

Review of the Savannah River Site, Waste Solidification Building, Construction Quality of Mechanical Systems Installation and Selected Aspects of Firre Protection System Design  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

the the Savannah River Site, Waste Solidification Building, Construction Quality of Mechanical Systems Installation and Selected Aspects of Fire Protection System Design January 2013 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy Independent Oversight Review of the Savannah River Site, Waste Solidification Building, Construction Quality of Mechanical Systems Installation and Selected Aspects of Fire Protection System Design Table of Contents 1.0 Purpose................................................................................................................................................. 1 2.0 Scope.................................................................................................................................................... 1

132

Reduction of fire hazards on large mining equipment  

SciTech Connect

Although standards and regulations are in place to prevent large mining equipment fires, recent analyses of mine accident data show that mining equipment fires still occur with alarming frequency and grave consequences, particularly at all surface mines and in underground metal/nonmetal mines. Recently technological advances in fire protection, combined with the statistical data on equipment fires, led NIOSH to reinvestigate this and to improve operator safety. NIOSH demonstrated that newly developed technologies, such as dual cab fire inerting systems and engine compartment fire barriers, can greatly enhance operator safety and lessen the damage of property during large mobile equipment fires. 10 refs., 5 figs.

Maria I. De Rosa

2008-09-15T23:59:59.000Z

133

R&D ERL: Machine Protection System  

SciTech Connect

The Machine Protection System (MPS) is a device-safety system that is designed to prevent damage to hardware by generating interlocks, based upon the state of input signals generated by selected sub-system. It exists to protect key machinery such as the 50 kW and 1 MW RF Systems. When a fault state occurs, the MPS is capable of responding with an interlock signal within several microseconds. The Machine Protection System inputs are designed to be fail-safe. In addition, all fault conditions are latched and time-stamped. The ERL MPS is based on a National Instruments hardware platform, and is programmed by utilizing National Instruments development environment for a visual programming language.

Altinbas, Z.

2010-01-01T23:59:59.000Z

134

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... pipes. Fluid Dispensing and Dispersion. ... Volume 2; Chapter 6 - Section 16; NFPA FPH2008;Fire Protection Handbook, 20th Edition. ...

135

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... NFPA FPH2008;Fire Protection Handbook, 20th Edition ... Nonazeotropic Refrigerant Mixutres in Thermodynamic Diagrams ... Control of Edge Heat Loss ...

136

DEVELOPMENT OF BURN TEST SPECIFICATIONS FOR FIRE PROTECTION MATERIALS IN RAM PACKAGES  

SciTech Connect

The regulations in 10 CFR 71 require that the radioactive material (RAM) packages must be able to withstand specific fire conditions given in 10 CFR 71.73 during Hypothetical Accident Conditions (HAC). This requirement is normally satisfied by extensive testing of full scale test specimens under required test conditions. Since fire test planning and execution is expensive and only provides a single snapshot into a package performance, every effort is made to minimize testing and supplement tests with results from computational thermal models. However, the accuracy of such thermal models depends heavily on the thermal properties of the fire insulating materials that are rarely available at the regulatory fire temperatures. To the best of authors knowledge no test standards exist that could be used to test the insulating materials and derive their thermal properties for the RAM package design. This paper presents a review of the existing industry fire testing standards and proposes testing methods that could serve as a standardized specification for testing fire insulating materials for use in RAM packages.

Gupta, N.

2010-03-03T23:59:59.000Z

137

Types of Cathodic Protection Systems  

Science Conference Proceedings (OSTI)

...requirements are relatively low. Electric power is not readily available. Short system life dictates a low capital investment. The anode is usually electrically connected by a wire or steel strap

138

Cathodic Protection System Application and Maintenance Guide  

Science Conference Proceedings (OSTI)

Typically, cathodic protection system equipment includes rectifiers, anodes, anode junction boxes, reference cells (electrodes), and test stations. The scope of this guide includes addressing the maintenance and testing of the system, its components, and providing appropriate recommendations. These recommendations will provide the basis for a suitable preventive (PM) and predictive (PdM) maintenance program.

2005-12-23T23:59:59.000Z

139

Advanced Integrated Systems Technology Development  

E-Print Network (OSTI)

refrigeration, and fire protection systems. Figure 2.1.2-1: CalSTRS Headquarters, Sacramento, CA (Mechanical design

2013-01-01T23:59:59.000Z

140

Reliability Assessment of SMART Reactor Protection System  

Science Conference Proceedings (OSTI)

Component failure rates and integrated system reliability of the SMART reactor protection system were analyzed. The analysis tool of the study was the RELEX 7 computer program developed by Relex Software Corporation. The RELEX software is a PC based computer program which includes the part stress analysis models and the RBD analysis model to calculate component and system reliability. The component failure rate data for the study was selected from the MIL-HDBK-217F. (authors)

Won Young, Yun; Choong Heui, Jeong [Korea Institute of Nuclear Safety, P. O. Box 114, Yusong Post Office, Daejeon (Korea, Republic of); Seong Hun, Kim; Sang Yong, Lee [Sam Chang Enterprise Co. LTD, 974-1, Goyen-ri, Woongchon-myon, Ulju-gun, Ulsan (Korea, Republic of)

2006-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Steam Turbine Electronic Overspeed Protection System  

Science Conference Proceedings (OSTI)

BackgroundThe risk of turbine-generator destructive overspeed can be mitigated by employing protection systems that act to rapidly isolate the steam supply in the event of separation from the grid. These systems are the final line of defense against overspeed, and they are deployed separately from the systems used to control turbine load and speed during synchronized operation. Most steam turbines in operation today were commissioned with a mechanical trip device that ...

2013-12-23T23:59:59.000Z

142

North Portal Fuel Storage System Fire Hazard Analysis-ESF Surface Design Package ID  

SciTech Connect

The purpose of the fire hazard analysis is to comprehensively assess the risk from fire within the individual fire areas. This document will only assess the fire hazard analysis within the Exploratory Studies Facility (ESF) Design Package ID, which includes the fuel storage system area of the North Portal facility, and evaluate whether the following objectives are met: 1.1.1--This analysis, performed in accordance with the requirements of this document, will satisfy the requirements for a fire hazard analysis in accordance with U.S. Department of Energy (DOE) Order 5480.7A. 1.1.2--Ensure that property damage from fire and related perils does not exceed an acceptable level. 1.1.3--Provide input to the ESF Basis For Design (BFD) Document. 1.1.4 Provide input to the facility Safety Analysis Report (SAR) (Paragraph 3.8).

N.M. Ruonavaara

1995-01-18T23:59:59.000Z

143

Lightning Direction-Finding Systems for Forest Fire Detection  

Science Conference Proceedings (OSTI)

Extensive networks of magnetic direction-finding (DF) stations have been installed throughout the western United States and Alaska to facilitate early detection of lightning-caused fires. Each station contains a new wideband direction-finder that ...

E. P. Krider; R. C. Noggle; A. E. Pifer; D. L. Vance

1980-09-01T23:59:59.000Z

144

Lightning protection system for a wind turbine  

DOE Patents (OSTI)

In a wind turbine (104, 500, 704) having a plurality of blades (132, 404, 516, 744) and a blade rotor hub (120, 712), a lightning protection system (100, 504, 700) for conducting lightning strikes to any one of the blades and the region surrounding the blade hub along a path around the blade hub and critical components of the wind turbine, such as the generator (112, 716), gearbox (708) and main turbine bearings (176, 724).

Costin, Daniel P. (Chelsea, VT); Petter, Jeffrey K. (Williston, VT)

2008-05-27T23:59:59.000Z

145

Coal-fired high performance power generating system  

SciTech Connect

The goals of the program are to develop a coal-fired high performance power generation system (HIPPS) by the year 2000 that is capable of > 47% thermal efficiency; NO[sub x] SO [sub x] and Particulates < 25% NSPS; Cost of electricity 10% lower; coal > 65% of heat input and all solid wastes benign. In order to achieve these goals our team has outlined a research plan based on an optimized analysis of a 250 MW[sub e] combined cycle system applicable to both frame type and aeroderivative gas turbines. Under the constraints of the cycle analysis we have designed a high temperature advanced furnace (HITAF) which integrates several combustor and air heater designs with appropriate ash management procedures. Most of this report discusses the details of work on these components, and the R D Plan for future work. The discussion of the combustor designs illustrates how detailed modeling can be an effective tool to estimate NO[sub x] production, minimum burnout lengths, combustion temperatures and even particulate impact on the combustor walls. When our model is applied to the long flame concept it indicates that fuel bound nitrogen will limit the range of coals that can use this approach. For high nitrogen coals a rapid mixing, rich-lean, deep staging combustor will be necessary. The air heater design has evolved into two segments: a convective heat exchanger downstream of the combustion process; a radiant panel heat exchanger, located in the combustor walls; The relative amount of heat transferred either radiatively or convectively will depend on the combustor type and the ash properties.

1992-07-01T23:59:59.000Z

146

Exploratory Studies Facility Subsurface Fire Hazards Analysis  

Science Conference Proceedings (OSTI)

The primary objective of this Fire Hazard Analysis (FHA) is to confirm the requirements for a comprehensive fire and related hazards protection program for the Exploratory Studies Facility (ESF) are sufficient to minimize the potential for: The occurrence of a fire or related event; A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of employees, the public or the environment; Vital U.S. Department of Energy (DOE) programs suffering unacceptable interruptions as a result of fire and related hazards; Property losses from a fire and related events exceeding limits established by DOE; and Critical process controls and safety class systems being damaged as a result of a fire and related events.

Richard C. Logan

2002-03-28T23:59:59.000Z

147

A Fire Risk Breakdown System for Electrical Power Lines in the North of Brazil  

Science Conference Proceedings (OSTI)

Anthropogenic or spontaneous fires (hotspots) are the main causes of unexpected breakdowns of electrical power lines in the North of Brazil. This research has tested, adapted and implemented a pre-operational system aiming to prevent electrical ...

Gutemberg Borges França; Antonio Nascimento de Oliveira; Célia Maria Paiva; Leonardo de Faria Peres; Michael Bezerra da Silva; Luciana Maria Temponi de Oliveira

148

Nuclear Power Plant Fire Modeling Application Guide (NPP FIRE MAG)  

Science Conference Proceedings (OSTI)

There is a movement to introduce risk-informed and performance-based (RI/PB) analyses into fire protection engineering practice, both domestically and worldwide.  This movement exists in both the general fire protection and the nuclear power plant (NPP) fire protection communities.  The U.S. Nuclear Regulatory Commission (NRC) has used risk-informed insights as a part of its regulatory decision making since the 1990s.In 2001, the National Fire Protection Association (NFPA) ...

2012-11-30T23:59:59.000Z

149

Fault-tolerant reactor protection system  

DOE Patents (OSTI)

A reactor protection system is disclosed having four divisions, with quad redundant sensors for each scram parameter providing input to four independent microprocessor-based electronic chassis. Each electronic chassis acquires the scram parameter data from its own sensor, digitizes the information, and then transmits the sensor reading to the other three electronic chassis via optical fibers. To increase system availability and reduce false scrams, the reactor protection system employs two levels of voting on a need for reactor scram. The electronic chassis perform software divisional data processing, vote 2/3 with spare based upon information from all four sensors, and send the divisional scram signals to the hardware logic panel, which performs a 2/4 division vote on whether or not to initiate a reactor scram. Each chassis makes a divisional scram decision based on data from all sensors. Each division performs independently of the others (asynchronous operation). All communications between the divisions are asynchronous. Each chassis substitutes its own spare sensor reading in the 2/3 vote if a sensor reading from one of the other chassis is faulty or missing. Therefore the presence of at least two valid sensor readings in excess of a set point is required before terminating the output to the hardware logic of a scram inhibition signal even when one of the four sensors is faulty or when one of the divisions is out of service. 16 figs.

Gaubatz, D.C.

1997-04-15T23:59:59.000Z

150

Repository Subsurface Preliminary Fire Hazard Analysis  

Science Conference Proceedings (OSTI)

This fire hazard analysis identifies preliminary design and operations features, fire, and explosion hazards, and provides a reasonable basis to establish the design requirements of fire protection systems during development and emplacement phases of the subsurface repository. This document follows the Technical Work Plan (TWP) (CRWMS M&O 2001c) which was prepared in accordance with AP-2.21Q, ''Quality Determinations and Planning for Scientific, Engineering, and Regulatory Compliance Activities''; Attachment 4 of AP-ESH-008, ''Hazards Analysis System''; and AP-3.11Q, ''Technical Reports''. The objective of this report is to establish the requirements that provide for facility nuclear safety and a proper level of personnel safety and property protection from the effects of fire and the adverse effects of fire-extinguishing agents.

Richard C. Logan

2001-07-30T23:59:59.000Z

151

Case history of industrial plant steam system layup for direct-fired gas operations  

Science Conference Proceedings (OSTI)

This paper presents the facts of an industrial plant steam system layup for direct fired gas operations. Fuel price savings indicated that gas firing a paper dryer, the largest steam user in the plant, would pay for itself in one year. Conversion work is detailed. Primary gas distribution was achieved by using one line of the steam loop. Machine water heating, power venting, space heating, and air makeup heating, among other conversions, are also specified.

Stacy, G.N.

1983-06-01T23:59:59.000Z

152

Electrical power systems protection and interdependencies with ICT  

Science Conference Proceedings (OSTI)

This section discusses the protection of electrical power systems (EPS) and its relation to the supporting Information and Communication Technologies (ICT) infrastructure. Several dimensions are addressed, ranging from the need of protection and available ... Keywords: critical infrastructures, disturbance, electrical power system, interdependencies, protection

George M. Milis; Elias Kyriakides; Antonis M. Hadjiantonis

2012-01-01T23:59:59.000Z

153

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Proceedings. October 15-17, 2008, Poznan, Poland, 1-8 pp, 2008. Domanski, PA; Yashar, DA; Kaufman, K. Fire Exposure Protection. ...

154

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Fundamentals of Combustion, Air Pollution and Global ... FPH2008;Fire Protection Handbook, 20th Edition ... Two-Step Combustion Chemistry for Large ...

155

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Fundamentals of Combustion, Air Pollution and Global ... FPH2008;Fire Protection Handbook, 20th Edition ... Royal Society of Chemistry, Cambridge, UK ...

156

Flame quality monitor system for fixed firing rate oil burners  

DOE Patents (OSTI)

A method and apparatus for determining and indicating the flame quality, or efficiency of the air-fuel ratio, in a fixed firing rate heating unit, such as an oil burning furnace, is provided. When the flame brightness falls outside a preset range, the flame quality, or excess air, has changed to the point that the unit should be serviced. The flame quality indicator output is in the form of lights mounted on the front of the unit. A green light indicates that the flame is about in the same condition as when the burner was last serviced. A red light indicates a flame which is either too rich or too lean, and that servicing of the burner is required. At the end of each firing cycle, the flame quality indicator goes into a hold mode which is in effect during the period that the burner remains off. A yellow or amber light indicates that the burner is in the hold mode. In this mode, the flame quality lights indicate the flame condition immediately before the burner turned off. Thus the unit can be viewed when it is off, and the flame condition at the end of the previous firing cycle can be observed.

Butcher, T.A.; Cerniglia, P.

1990-10-23T23:59:59.000Z

157

Flame quality monitor system for fixed firing rate oil burners  

DOE Patents (OSTI)

A method and apparatus for determining and indicating the flame quality, or efficiency of the air-fuel ratio, in a fixed firing rate heating unit, such as an oil burning furnace, is provided. When the flame brightness falls outside a preset range, the flame quality, or excess air, has changed to the point that the unit should be serviced. The flame quality indicator output is in the form of lights mounted on the front of the unit. A green light indicates that the flame is about in the same condition as when the burner was last serviced. A red light indicates a flame which is either too rich or too lean, and that servicing of the burner is required. At the end of each firing cycle, the flame quality indicator goes into a hold mode which is in effect during the period that the burner remains off. A yellow or amber light indicates that the burner is in the hold mode. In this mode, the flame quality lights indicate the flame condition immediately before the burner turned off. Thus the unit can be viewed when it is off, and the flame condition at the end of the previous firing cycle can be observed.

Butcher, Thomas A. (Pt. Jefferson, NY); Cerniglia, Philip (Moriches, NY)

1992-01-01T23:59:59.000Z

158

Fire science at LLNL: A review  

SciTech Connect

This fire sciences report from LLNL includes topics on: fire spread in trailer complexes, properties of welding blankets, validation of sprinkler systems, fire and smoke detectors, fire modeling, and other fire engineering and safety issues. (JEF)

Hasegawa, H.K. (ed.)

1990-03-01T23:59:59.000Z

159

Computer-aided coordination and overcurrent protection for distribution systems  

Science Conference Proceedings (OSTI)

Overcurrent protection and coordination studies for electrical distribution systems have become much easier to perform with the emergence of several commercially available software programs that run on a personal computer. These programs have built-in libraries of protective device time-current curves, damage curves for cable and transformers, and motor starting curves, thereby facilitating the design of a selectively coordinated protection system which is also well-protected. Additionally, design time when utilizing computers is far less than the previous method of tracing manufacturers` curves on transparent paper. Basic protection and coordination principles are presented in this paper along with several helpful suggestions for designing electrical protection systems. A step-by-step methodology is presented to illustrate the design concepts when using software for selecting and coordinating the protective devices in distribution systems.

Tolbert, L.M.

1995-03-01T23:59:59.000Z

160

Interim guidelines for protecting fire-fighting personnel from multiple hazards at nuclear plant sites: Final report  

Science Conference Proceedings (OSTI)

This report provides interim guidelines for reducing the impact to fire fighting and other supporting emergency response personnel from the multiple hazards of radiation, heat stress, and trauma when fighting a fire in a United States commercial nuclear power plant. Interim guidelines are provided for fire brigade composition, training, equipment, procedures, strategies, heat stress and trauma. In addition, task definitions are provided to evaluate and further enhance the interim guidelines over the long term. 19 refs.

Klein, A.R.; Bloom, C.W.

1989-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Protecting Computer Systems Against Power Transients  

Science Conference Proceedings (OSTI)

... protection may be more important than some data loss. ... by a telephone or other network link to ... are buffered by the computer's power supply but ...

2013-05-17T23:59:59.000Z

162

Fire protection of railroad tank cars carrying hazardous materials - analytical calculations and laboratory screening of thermal insulation candidates  

SciTech Connect

In recent years there have been a number of incidents in which railroad tank cars carrying liquefied petroleum gas (LPG) have been engulfed in fires. The LPG cars have ruptured from the fires, causing extensive property damage and loss of life. This report describes a laboratory screening program to select two thermal insulation candidates for use in future fire tests of fifth-scale and full scale LPG tank cars. Also included are analytical calculations to predict pressures and liquid levels in LPG tank cars being heated by fires.

Levine, D.; Dancer, D.M.

1972-07-21T23:59:59.000Z

163

Sept. 2009 Fire Retardants Workshop Agenda and ...  

Science Conference Proceedings (OSTI)

... The role of NIOSH in protecting the on-the-job health of fire ... Life Cycle Analysis of Fire Retardants, Dr. Margaret Simonson McNamee, Research ...

2011-11-16T23:59:59.000Z

164

Optimal Maintenance for Modern Protection and Control Systems  

Science Conference Proceedings (OSTI)

Many blackouts have protection system misoperation as a root cause. A maintenance program for a protection and control (P&C) system is a critical and required task for the reliability of power system operation. Although today’s digital technologies have revolutionarily changed the P&C infrastructure, its maintenance approaches and methodologies remain largely unchanged from the electromechanical protection era. The enabling technologies available today can provide utilities more ...

2012-12-14T23:59:59.000Z

165

The Carbon Emission Analysis System Design of Coal-Fired Unit  

Science Conference Proceedings (OSTI)

Carbon dioxide is the main cause of global warming, that emission has been the world's attention. and the power industry is an important source of carbon dioxide emissions, this paper try to design the system of power plants for carbon emissions coal-fired ... Keywords: Analysis system, Carbon emissions, Energy saving

Han Jieping; Zhang Chengzhen

2011-08-01T23:59:59.000Z

166

Fire Egress  

NLE Websites -- All DOE Office Websites (Extended Search)

OSHAX.org - OSHAX.org - The Unofficial Guide To the OSHA 1 Introduction ď‚ž Fires and explosions kill more than 200 and injure more than 5,000 workers each year ď‚ž There is a long and tragic history of workplace fires in this country caused by problems with fire exits and extinguishing systems ď‚ž OSHA requires employers to provide proper exits, fire fighting equipment, and employee training to prevent fire deaths and injuries in the workplace OSHAX.org - The Unofficial Guide To the OSHA 2 Exit Route ď‚ž A continuous and unobstructed path of exit travel from any point within a workplace to a place of safety (including refuge areas) ď‚ž Consists of three parts: ď‚— Exit access ď‚— Exit ď‚— Exit discharge OSHAX.org - The Unofficial Guide To the OSHA 3 Exit Routes Basic Requirements

167

Engineering development of advanced coal-fired low-emission boiler system  

Science Conference Proceedings (OSTI)

The Pittsburgh Energy Technology Center of the US Department of Energy (DOE) has contracted with Combustion Engineering, Inc. (ABB CE) to perform work on the Engineering Development of Advanced Coal-Fired Low-Emission Boiler Systems'' Project and has authorized ABB CE to complete Phase I on a cost-reimbursable basis. The overall objective of the Project is the expedited commercialization of advanced coal-fired low-emission boiler systems. The specified primary objectives are: NO[sub x] emissions not greater than one-third NSPS; SO[sub x] emissions not greater than one-third NSPS; and particulate emissions not greater than one-half NSPS. The specific secondary objectives are: Improved ash disposability and reduced waste generation; reduced air toxics emissions; increased generating efficiency. The final deliverables are a design data base that will allow future coal-fired power plants to meet the stated objectives and a preliminary design of a commercial generation unit.

Not Available

1993-02-26T23:59:59.000Z

168

Development of a Software System to Facilitate Implementation of Coal and Wood Co-Fired Bilers  

E-Print Network (OSTI)

Coal and wood co-fired boiler technology has improved significantly over the years. The term "co-firing", when used by members of the biomass or utility communities, has come to mean mixing a modest amount of clean, dry sawdust with coal and burning the sawdust coal mixture in a large, coal-burning, utility boiler. This paper discusses the development of a computer software system that interacts with the user and allows coal-wood co-fired boilers to be sized, priced, implemented, and operated properly. Information about the equipment that is required for the boiler replacement project is provided. Along with these features, the software would allow the user to determine energy and cost savings that would be available upon installation as compared to other types of boilers. The paper outlines how these savings are realized, and the steps that must be taken to ensure the proper operation of the boiler to achieve these savings. A sensitivity analysis has also been performed on the implementation of coal-wood co-fired boilers in order to determine the key factors influencing the project payback period. The key factors that are considered in the analysis are the boiler size, the annual operating hours, and the current fuel cost. Additional analysis has been done on the boiler size and the annual operating hours. This analysis allows the users to determine if their current facility falls into the feasible range for implementing a coal-wood co-fired boiler system.

Gopalakrishnan, B.; Gump, C. D.; Gupta, D. P.; Chaudhari, S.

2013-01-01T23:59:59.000Z

169

Brookhaven National Laboratory/ LIGHT SOURCES DIRECTORATE Subject: Building 729 Fire Hazard Assessment/ Fire Hazard Analysis  

E-Print Network (OSTI)

Alarm Code, NFPA 72, 2002 Life Safety Code, NFPA 101, 2006 Emergency and Standby Power Systems, NFPA 110 Code, NFPA 70, 2008. Standard for Electrical Safety in the Workplace, NFPA 70E, 2004 National Fire in accordance with NFPA 780 and UL 96A. 10.4.6 Cathodic protection: Cathodic protection will not be provided. 10

Ohta, Shigemi

170

Radio frequency security system, method for a building facility or the like, and apparatus and methods for remotely monitoring the status of fire extinguishers  

DOE Patents (OSTI)

A system for remotely monitoring the status of one or more fire extinguishers includes means for sensing at least one parameter of each of the fire extinguishers; means for selectively transmitting the sensed parameters along with information identifying the fire extinguishers from which the parameters were sensed; and means for receiving the sensed parameters and identifying information for the fire extinguisher or extinguishers at a common location. Other systems and methods for remotely monitoring the status of multiple fire extinguishers are also provided.

Runyon, Larry (Richland, WA); Gunter, Wayne M. (Richland, WA); Gilbert, Ronald W. (Gilroy, CA)

2006-07-25T23:59:59.000Z

171

THE DEVELOPMENT OF PROTECTIVE EQUIPMENT FOR NUCLEAR DECONTAMINATION SYSTEMS  

SciTech Connect

BS>A review of various types of protective equipment used in connection with radioactive decontamination systems is presented. A description of decontamination areas, decontamination methods, laundry techniques, active waste handling, protective suits, air hose systems, control room systems, clean air supplies, routine maintenance and emergency systems, mobile units, disposable suit techniques, respirators and air line masks, and high velocity cooling systems is given. (C.E.S.)

Thorne, A.C.

1963-06-01T23:59:59.000Z

172

Study on Relay Protection Coordination in Complex Auxiliary Power System  

Science Conference Proceedings (OSTI)

In many large-scale power plants, the structure of its auxiliary power system are complex, and the coordination of its relay protections is difficult. The Three Gorges Hydropower Plant is the largest installed capacity of power plants with complex auxiliary ... Keywords: auxiliary power system, relay protection, coordination

Yawen Yi; Jun Xie; Na Yi

2010-06-01T23:59:59.000Z

173

Passive Fire Protection  

Science Conference Proceedings (OSTI)

... Trade Center Disaster: The Con Ed Substation in World ... under contract by a commercial testing agency ... Specimen Preparation and Test Procedures ...

174

Workshop on Fire Protection  

Science Conference Proceedings (OSTI)

... detailed information about moisture levels at testing and ... classifications that are derived from the test. All ... hili I din gr (' q II ir (' m(' nts, SIIC11 «Issp ...

2009-04-06T23:59:59.000Z

175

Operational test report -- Project W-320 cathodic protection systems  

Science Conference Proceedings (OSTI)

Washington Administrative Code (WAC) 173-303-640 specifies that corrosion protection must be designed into tank systems that treat or store dangerous wastes. Project W-320, Waste Retrieval Sluicing System (WRSS), utilizes underground encased waste transfer piping between tanks 241-C-106 and 241-AY-102. Corrosion protection is afforded to the encasements of the WRSS waste transfer piping through the application of earthen ionic currents onto the surface of the piping encasements. Cathodic protection is used in conjunction with the protective coatings that are applied upon the WRSS encasement piping. WRSS installed two new two rectifier systems (46 and 47) and modified one rectifier system (31). WAC 173-303-640 specifies that the proper operation of cathodic protection systems must be confirmed within six months after initial installation. The WRSS cathodic protection systems were energized to begin continuous operation on 5/5/98. Sixteen days after the initial steady-state start-up of the WRSS rectifier systems, the operational testing was accomplished with procedure OTP-320-006 Rev/Mod A-0. This operational test report documents the OTP-320-006 results and documents the results of configuration testing of integrated piping and rectifier systems associated with the W-320 cathodic protection systems.

Bowman, T.J.

1998-06-16T23:59:59.000Z

176

Protected Water Area System (Iowa) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Protected Water Area System (Iowa) Protected Water Area System (Iowa) Protected Water Area System (Iowa) < Back Eligibility Agricultural Commercial Construction Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Iowa Program Type Environmental Regulations Provider Iowa Department of Natural Resources The Natural Resource Commission maintains a state plan for the design and

177

Development of a high-performance coal-fired power generating system with pyrolysis gas and char-fired high temperature furnace (HITAF)  

SciTech Connect

A concept for an advanced coal-fired combined-cycle power generating system is currently being developed. The first phase of this three-phase program consists of conducting the necessary research and development to define the system, evaluate the economic and technical feasibility of the concept, and prepare an R D plan to develop the concept further. Foster Wheeler Development Corporation is leading a team ofcompanies involved in this effort. The system proposed to meet these goals is a combined-cycle system where air for a gas turbine is indirectly heated to approximately 1800[degrees]F in furnaces fired with cool-derived fuels and then directly heated in a natural-gas-fired combustor up to about 2400[degrees]F. The system is based on a pyrolyzing process that converts the coal into a low-Btu fuel gas and char. The fuelgas is a relatively clean fuel, and it is fired to heat tube surfaces that are susceptible to corrosion and problems from ash deposition. In particular, the high-temperature air heater tubes, which will need tobe a ceramic material, will be located in a separate furnace or region of a furnace that is exposed to combustion products from the low-Btu fuel gas only. A simplified process flow diagram is shown.

Not Available

1992-11-01T23:59:59.000Z

178

Development of Low-Maintenance Protection and Control Systems  

Science Conference Proceedings (OSTI)

Protection and control (P&C) system maintenance is a critical task and requirement for the reliability of power grid. Traditionally, electro-mechanic devices require regular calibration and maintenance for proper operations. Thus, time-based maintenance programs have been developed by utilities and have not changed much even after the industry migrated to the microprocessor and communication-based digital protection technologies. The Electric Power Research Institute (EPRI) Protection and Control Task Fo...

2011-12-13T23:59:59.000Z

179

Power System Transmission Protection: Proposed R&D Projects  

Science Conference Proceedings (OSTI)

The U.S.-Canada task force on the August 14, 2003 power system outage that affected 50 million people concluded that inappropriate and uncoordinated relay protection settings were one of the three principal reasons that the cascade outage spread beyond Ohio and caused the widespread blackout. Based on input from utilities and other stakeholders at a recent protection workshop, this report proposes four R&D project to help meet needs in the transmission protection area.

2005-09-14T23:59:59.000Z

180

NETL: News Release - Novel Coal-Fired Heating System Proves Successful at  

NLE Websites -- All DOE Office Websites (Extended Search)

December 20, 2005 December 20, 2005 Novel Coal-Fired Heating System Proves Successful at Ohio Greenhouse Cost Savings and State EPA Standards Achieved in First Commercial Demonstration WASHINGTON, DC - Using a Department of Energy - funded coal-fired technology, a greenhouse in northeast Ohio is saving more than $1,000 a day in heating costs. The efficient fluidized-bed combustion unit provides an alternative to natural gas systems and, using locally available coal and limestone, surpasses state EPA standards for sulfur capture and stack emissions. "The promise of the unit lies in its novel design," said Donald Bonk, a senior technical advisor for the National Energy Technology Laboratory (NETL), which manages the project for the Energy Department. "The fluidized-bed combustion system features flue-gas recirculation, replacing conventional, more expensive boiler tubes. By recycling the flue gas, the system better controls internal temperatures to burn fuel, reducing the formation of pollutants."

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

2012 Facility Representative/Safety System Oversight/Fire Safety Workshop Agenda  

NLE Websites -- All DOE Office Websites (Extended Search)

Facility Representative ď‚· Safety System Oversight ď‚· Fire Safety Facility Representative ď‚· Safety System Oversight ď‚· Fire Safety Overall Workshop Agenda May 14-18, 2012 ď‚· Alexis Park Hotel ď‚· Las Vegas, Nevada Monday, May 14, 2012 8:00 a.m. - 5:00 p.m. SAF-271, SSO Assessments (Day 1) Zeus B Quality Assurance Overview for FR/SSO Personnel Zeus A 5:00 p.m. - 7:00 p.m. Workshop Registration Zeus Foyer Tuesday, May 15, 2012 8:00 a.m. - 5:00 p.m. Fire Safety Workshop Track Begins (see track agenda) Parthenon 4 SAF-271, SSO Assessments (Day 2) Zeus B . Safety Culture Workshop Zeus A Federal Technical Capability Panel Parthenon 2 5:00 p.m. - 7:00 p.m. Workshop Registration Zeus Foyer Wednesday, May 16, 2012 6:30 a.m. - 7:45 a.m. Workshop Registration Zeus Foyer 8:00 a.m. - 11:30 a.m. FR/SSO Tracks Begin; Plenary session with Fire Safety Track Parthenon 2 & 4

182

Integration and operation of post-combustion capture system on coal-fired power generation: load following and peak power  

E-Print Network (OSTI)

Coal-fired power plants with post combustion capture and sequestration (CCS) systems have a variety of challenges to integrate the steam generation, air quality control, cooling water systems and steam turbine with the ...

Brasington, Robert David, S.M. Massachusetts Institute of Technology

2012-01-01T23:59:59.000Z

183

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... systems; surface temperature; deflection; insulation; thermometers; structural ... effects of fires in buildings, for use ... the analysis of building response to ...

184

Development and design of an advanced pulverized coal-fired system  

SciTech Connect

Under the US Department of Energy (DOE) project `Engineering Development of Advanced Coal-Fired Low-Emission Boiler Systems` (LEBS) the ABB team developed the design of a 400 MWe advanced pulverized coal fired electric generating system. The work and the results are described in the paper. Early work included concept development and evaluation of several subsystems for controlling the emission of SO{sub 2}, NO{sub x}, particulates and for reducing wastes. Candidate technologies were then evaluated in various combinations as part of complete advanced supercritical power generation systems. One system was selected for the design of the advanced generating system. Pilot scale testing is now being conducted to support the design of subsystems. The design meets the overall objective of the LEBS Project by dramatically improving environmental performance of pulverized coal fired power plants without adversely impacting efficiency or the cost of electricity. Advanced technologies will be used to reduce NO{sub x}, SO{sub 2}, and particulate emissions to one-fifth to one-tenth of current NSPS limits. Air toxics will be in compliance, and wastes will be reduced and made more disposable. Net station (HHV) efficiency can be increased to 45 percent without increasing the cost of electricity.

Regan, J.W.; Borio, R.W.; Palkes, M. [ABB Power Plant Laboratories (United States); Mirolli, M.D. [ABB Combustion Engineering, Inc., Windsor, CT (United States); Wesnor, J.D. [ABB Environmental Systems, Birmingham, AL (United States); Bender, D.J. [Raytheon Engineers & Constructors, Inc. (United States)

1995-12-31T23:59:59.000Z

185

Reliability estimation for multiunit nuclear and fossil-fired industrial energy systems  

SciTech Connect

The purpose of this paper is twofold: to report industrial experience with process energy system reliability, and to assess the reliability of multiunit nuclear and fossil-fired energy systems in an industrial setting. Reliability here refers to the percentage of clock time that sufficient amounts of steam energy were available to permit desired production quotas to be met at a particular plant. A nationwide survey was conducted to obtain data relative to energy system reliabilities during 1973--74, and these data for 29 plants from chemicals and allied products (S.I.C. 28), petroleum refining and related industries (S.I.C. 29) and primary metals industries (S.I.C. 33) are reported here. A simulation model in which various operating characteristics of the energy systems were taken into account was developed to obtain estimates of reliabilities of proposed multiunit nuclear and fossil-fired systems. Based on several example problems evaluated with the simulation model, study results indicated that multiple nuclear units or a combination of nuclear and fossil-fired units could provide adequate reliability to meet large-scale industrial requirements for continuity of service.

Sullivan, W.G.; Wilson, J.V.; Klepper, O.H.

1978-01-01T23:59:59.000Z

186

ENGINEERING DEVELOPMENT OF COAL-FIRED HIGH-PERFORMANCE POWER SYSTEMS  

SciTech Connect

A High Performance Power System (HIPPS) is being developed. This system is a coal-fired, combined cycle plant with indirect heating of gas turbine air. Foster Wheeler Development Corporation and a team consisting of Foster Wheeler Energy Corporation, Bechtel Corporation, University of Tennessee Space Institute and Westinghouse Electric Corporation are developing this system. In Phase 1 of the project, a conceptual design of a commercial plant was developed. Technical and economic analyses indicated that the plant would meet the goals of the project which include a 47 percent efficiency (HHV) and a 10 percent lower cost of electricity than an equivalent size PC plant. The concept uses a pyrolyzation process to convert coal into fuel gas and char. The char is fired in a High Temperature Advanced Furnace (HITAF). The HITAF is a pulverized fuel-fired boiler/air heater where steam is generated and gas turbine air is indirectly heated. The fuel gas generated in the pyrolyzer is then used to heat the gas turbine air further before it enters the gas turbine. The project is currently in Phase 2, which includes engineering analysis, laboratory testing and pilot plant testing. Research and development is being done on the HIPPS systems that are not commercial or being developed on other projects. Pilot plant testing of the pyrolyzer subsystem and the char combustion subsystem are being done separately, and after each experimental program has been completed, a larger scale pyrolyzer will be tested at the Power Systems Development Facility (PSDF) in Wilsonville, AL. The facility is equipped with a gas turbine and a topping combustor, and as such, will provide an opportunity to evaluate integrated pyrolyzer and turbine operation. This report addresses the areas of technical progress for this quarter. In order to prepare the CETF for the HIPPS char combustion test program, the following three subsystems were designed during this quarter: (1) Flue Gas Recycle System; (2) Pulverized Coal Feed System; and (3) Limestone Feed System The flue gas recycle system is added to simulate the performance of a commercial char burner fired with gas turbine exhaust. Since synthetically made char will be used for the tests at the CETF, the limestone injection system was added to produce a char more representative of that from an actual pyrolyzer. The pulverized coal system is included to provide a supplemental support fuel if a stable flame can not be maintained with char firing only.

1998-10-01T23:59:59.000Z

187

ULTRA LOW NOx INTEGRATED SYSTEM FOR NOx EMISSION CONTROL FROM COAL-FIRED BOILERS  

Science Conference Proceedings (OSTI)

ALSTOM Power Inc.'s Power Plant Laboratories, working in concert with ALSTOM Power's Performance Projects Group, has teamed with the U.S. Department of Energy's National Energy Technology Laboratory (DOE NETL) to conduct a comprehensive study to develop/evaluate low-cost, efficient NOx control technologies for retrofit to pulverized coal fired utility boilers. The objective of this project was to develop retrofit NOx control technology to achieve less than 0.15 lb/MMBtu NOx (for bituminous coals) and 0.10 lb/MMBtu NOx (for subbituminous coals) from existing pulverized coal fired utility boilers at a cost which is at least 25% less than SCR technology. Efficient control of NOx is seen as an important, enabling step in keeping coal as a viable part of the national energy mix in this century, and beyond. Presently 57% of U.S. electrical generation is coal based, and the Energy Information Agency projects that coal will maintain a lead in U.S. power generation over all other fuel sources for decades (EIA 1998 Energy Forecast). Yet, coal-based power is being strongly challenged by society's ever-increasing desire for an improved environment and the resultant improvement in health and safety. The needs of the electric-utility industry are to improve environmental performance, while simultaneously improving overall plant economics. This means that emissions control technology is needed with very low capital and operating costs. This project has responded to the industry's need for low NOx emissions by evaluating ideas that can be adapted to present pulverized coal fired systems, be they conventional or low NOx firing systems. The TFS 2000{trademark} firing system has been the ALSTOM Power Inc. commercial offering producing the lowest NOx emission levels. In this project, the TFS 2000{trademark} firing system served as a basis for comparison to other low NOx systems evaluated and was the foundation upon which refinements were made to further improve NOx emissions and related combustion performance. Three coals were evaluated during the bench-scale and large pilot-scale testing tasks. The three coals ranged from a very reactive Powder River Basin coal (PRB) to a moderately reactive Midwestern bituminous coal (HVB) to a less reactive medium volatile Eastern bituminous coal (MVB). Bench-scale testing was comprised of standard ASTM properties evaluation, plus more detailed characterization of fuel properties through drop tube furnace testing and thermogravimetric analysis.

Galen H. Richards; Charles Q. Maney; Richard W. Borio; Robert D. Lewis

2002-12-30T23:59:59.000Z

188

Dilution-based emissions sampling from stationary sources: part 2 - gas-fired combustors compared with other fuel-fired systems  

SciTech Connect

With the recent focus on fine particle matter (PM2.5), new, self- consistent data are needed to characterize emissions from combustion sources. Emissions data for gas-fired combustors are presented, using dilution sampling as the reference. The sampling and analysis of the collected particles in the presence of precursor gases, SO{sub 2}, nitrogen oxide, volatile organic compound, and NH{sub 3} is discussed; the results include data from eight gas fired units, including a dual- fuel institutional boiler and a diesel engine powered electricity generator. These data are compared with results in the literature for heavy-duty diesel vehicles and stationary sources using coal or wood as fuels. The results show that the gas-fired combustors have very low PM2.5 mass emission rates in the range of {approximately}10{sup -4} lb/million Btu (MMBTU) compared with the diesel backup generator with particle filter, with {approximately} 5 x 10{sup -3} lb/MMBTU. Even higher mass emission rates are found in coal-fired systems, with rates of {approximately} 0.07 lb/MMBTU for a bag-filter-controlled pilot unit burning eastern bituminous coal. The characterization of PM2.5 chemical composition from the gas-fired units indicates that much of the measured primary particle mass in PM2.5 samples is organic or elemental carbon and, to a much less extent, sulfate. Metal emissions are low compared with the diesel engines and the coal- or wood-fueled combustors. The metals found in the gas- fired combustor particles are low in concentration. The interpretation of the particulate carbon emissions is complicated by the fact that an approximately equal amount of particulate carbon is found on the particle collector and a backup filter. It is likely that measurement artifacts are positively biasing 'true' particulate carbon emissions results. 49 refs., 1 fig., 12 tabs.

England, G.C.; Watson, J.G.; Chow, J.C.; Zielinska, B.; Chang, M.C.O.; Loos, K.R.; Hidy. G.M. [GE Energy, Santa Ana, CA (United States)

2007-01-15T23:59:59.000Z

189

Parameters affecting nitrogen oxides in a Coal-Fired Flow Facility system  

DOE Green Energy (OSTI)

The unusually high temperature in the primary combustor of the Coal-Fired Magnetohydrodynamics (MHD) power generation system causes much higher nitrogen oxides (NO{sub x}) to be produced than in a conventional coal fired generation system. In order to lower the NO{sub x} concentration to an acceptable level, it is important to know how parameters of the MM power generation system affect the NO{sub x} concentration. This thesis investigates those effects in the Coal-Fired Flow Facility (CFFF) at the University of Tennessee Space Institute under the contract of US Department Of Energy (DOE). With thermodynamic and kinetic computer codes, the theoretical studies were carried out on the parameters of the CFFF system. The results gathered from the computer codes were analyzed and compared with the experimental data collected during the LMF5J test. The thermodynamic and kinetic codes together modeled the NO.{sub x} behavior with reasonable accuracy while some inconsistencies happened at the secondary combustor inlet.

Lu, Xiaoliang

1996-03-01T23:59:59.000Z

190

Development and demonstration of a wood-fired gas turbine system  

DOE Green Energy (OSTI)

The objectives of the test program were to obtain some preliminary information regarding the nature of particulate and vapor phase alkali compounds produced and to assess any deleterious impact they might have on materials of construction. Power Generating Incorporated (PGI) is developing a wood-fired gas turbine system for specialized cogeneration applications. The system is based on a patented pressurized combustor designed and tested by PGI in conjunction with McConnell Industries. The other components of the system are fuel receiving, preparation, storage and feeding system, gas clean-up equipment, and a gas turbine generator.

Smith, V.; Selzer, B.; Sethi, V.

1993-08-01T23:59:59.000Z

191

2012 Facility Representative/Safety System Oversight/Fire Safety Workshop - Registrants  

NLE Websites -- All DOE Office Websites (Extended Search)

Facility Representative / Safety System Oversight Workshop Facility Representative / Safety System Oversight Workshop DOE Fire Safety Workshop Federal Technical Capability Panel (FTCP) Meeting May 14 - 18, 2012, at the Alexis park Resort Hotel, Las Vegas, NV Registrants As of 5/15/2012 Total Number: 218 First Name Last Name Government /Contractor Agency Secretarial Office Site Position Training Course FTCP FS 5/15 FS 5/16 FR/SSO Plenary FR Track SSO Track Fire Safety Training Tour Ron Alderson Government Employee DOE NNSA Nevada SSO SAF-271 No No No Yes No Yes No No Josh Allen Government Employee DOE EM Richland FR No No No No Yes Yes No No No Mark Alsdorf Government Employee DOE HSS Headquarters NTC Safety Training Manager SAF-271 Yes No No Yes No No No No Xavier Aponte Government Employee

192

Development and demonstration of a solid fuel-fired gas turbine system  

SciTech Connect

Western Research Institute (WRI) and Power Generating Incorporated (PGI) are developing a solid fuel-fired gas turbine system for specialized cogeneration applications. The system is based on a patented pressurized combustor designed and tested by PGI in conjunction with McConnell Industries. The other components of the system are (a) fuel receiving, preparation, storage and feeding system, (b) gas clean-up equipment, and (c) a gas turbine generator. An approximately 400 kW prototype system is under construction at the WRI facilities in Laramie, Wyoming. As a part of this demonstration the integrated system, following a short shakedown period, will be operated on white wood. White wood was selected as the fuel for early tests because of its low ash (0.5 - 1.0 %), silica, and sulfur contents. The system will then be operated on coal. It is expected that the design of the coal-based system will evolve as the wood testing proceeds. In previous similar wood-fired system development attempts, albeit at lower turbine inlet temperatures, a major technical hindrance to long-term operation of a gas turbine power system has been the degradation of the hot section of the gas turbine. Deposition, erosion, and corrosion are main issues that need to be addressed. In the wood-fired PGI system, erosion is not likely to be of concern because of the low silica and low overall ash content of the fuel and the fact that the wood ash particle size is expected to be in the range where little or no erosion would be expected. However, because of the high alkali content of the fuel, deposition and corrosion can become major issues. This paper will deal with the issues pertaining to the design of the prototype being constructed at the WRI premises. Preliminary thoughts on the design aspects of the plant modifications required for coal testing will also be presented.

Speight, J.G.; Sethi, V.K.

1995-11-01T23:59:59.000Z

193

Gas fired advanced turbine system. Phase 1, System scoping and feasibility studies  

DOE Green Energy (OSTI)

The basic concept thus derived from the Ericsson cycle is an intercooled, recuperated, and reheated gas turbine. Theoretical performance analyses, however, showed that reheat at high turbine rotor inlet temperatures (TRIT) did not provide significant efficiency gains and that the 50 percent efficiency goal could be met without reheat. Based upon these findings, the engine concept adopted as a starting point for the gas-fired advanced turbine system is an intercooled, recuperated (ICR) gas turbine. It was found that, at inlet temperatures greater than 2450{degrees}F, the thermal efficiency could be maintained above 50%, provided that the turbine cooling flows could be reduced to 7% of the main air flow or lower. This dual and conflicting requirement of increased temperatures and reduced cooling will probably force the abandonment of traditional air cooled turbine parts. Thus, the use of either ceramic materials or non-air cooling fluids has to be considered for the turbine nozzle guide vanes and turbine blades. The use of ceramic components for the proposed engine system is generally preferred because of the potential growth to higher temperatures that is available with such materials.

LeCren, R.T.; White, D.J.

1993-11-01T23:59:59.000Z

194

Emergency Elevator Evacuation Systems  

Science Conference Proceedings (OSTI)

... feeds, power from multiple substations outsidethe building,and ... of Fire Protection Engineering, Society of Fire Protection Engineers, Boston, MA. ...

1996-08-14T23:59:59.000Z

195

Distribution System Protection with Communication Technologies  

E-Print Network (OSTI)

(Combined Heating and Power) and small scaled WTs (Wind Turbines), as a practical example to examine, and hydro power, etc. are rapidly evolved and involved in contemporary power systems. The power system

Chen, Zhe

196

Development and demonstration of a wood-fired gas turbine system  

DOE Green Energy (OSTI)

Power Generating Inc. (PGI) has developed and patented a unique direct-fired gas turbine power system (PGI Power System) that operates on solid wood-based fuels. The PGI Power System is designed to generate from 500 kilowatts to 3.5 megawatts of electrical power and up to 30 million Btu per hour of thermal energy for various industrial and utility applications. The system is expected to operate at thermal efficiency levels greater than 70% through full utilization of both the electrical and thermal energy it generates at a specific host facility. PGI and WRI built a 450-kW prototype system at the Western Research Institute (WRI) facilities in Laramie, Wyoming, to demonstrate the technical and economic viability of the PGI Power System. The plant has undergone a brief shakedown, and is presently being operated on white wood. In previous attempts to develop similar systems, the major technical hindrance to long-term operation of a gas turbine power system has been degradation of the hot section in the gas turbine. This problem is overcome in the PGI Power System through its unique design, by closely controlling fuel specifications, and by developing specialized operating procedures. In wood-fired testing conducted to date, no degradation in the engine performance is obvious.

Sethi, V.

1997-10-01T23:59:59.000Z

197

Electrical Sitchgear Building No. 5010-ESF Fire Hazards Technical Report  

SciTech Connect

The purpose of this Fire Hazards Analysis Technical Report (hereinafter referred to as Technical Report) is to assess the risk from fire within individual fire areas to ascertain whether the U.S. Department of Energy (DOE) fire safety objectives are met. The objectives, identified in DOE Order 420.1, Change 2, Fire Safety, Section 4.2, establish requirements for a comprehensive fire and related hazards protection program for facilities sufficient to minimize the potential for: (1) The occurrence of a fire or related event; (2) A fire that causes an unacceptable on-site or off-site release of hazardous or radiological material that will threaten the health and safety of the employees, the public, and the environment; (3) Vital DOE programs suffering unacceptable interruptions as a result of fire and related hazards; (4) Property losses from a fire and related events exceeding defined limits established by DOE; and (5) Critical process controls and safety class systems being damaged as a result of a fire and related event.

N.M. Ruonavaara

2001-05-08T23:59:59.000Z

198

Definition: Protection System | Open Energy Information  

Open Energy Info (EERE)

control circuitry.1 View on Wikipedia Wikipedia Definition Related Terms system, sustainability References Glossary of Terms Used in Reliability Standards An i LikeLike...

199

Influence of instrument transformers on power system protection  

E-Print Network (OSTI)

Instrument transformers are a crucial component of power system protection. They supply the protection system with scaled-down replicas of current and voltage signals present in a power network to the levels which are safe and practical to op- erate with. The conventional instrument transformers are based on electromagnetic coupling between the power network on the primary side and protective devices on the secondary. Due to such a design, instrument transformers insert distortions in the mentioned signal replicas. Protective devices may be sensitive to these distortions. The inuence of distortions may lead to disastrous misoperations of protective devices. To overcome this problem, a new instrument transformer design has been devised: optical sensing of currents and voltages. In the theory, novel instrument transform- ers promise a distortion-free replication of the primary signals. Since the mentioned novel design has not been widely used in practice so far, its superior performance needs to be evaluated. This poses a question: how can the new technology (design) be evaluated, and compared to the existing instrument transformer technology? The importance of this question lies in its consequence: is there a necessity to upgrade the protection system, i.e. to replace the conventional instrument transformers with the novel ones, which would be quite expensive and time-consuming? The posed question can be answered by comparing inuences of both the novel and the conventional instrument transformers on the protection system. At present, there is no systematic approach to this evaluation. Since the evaluation could lead to an improvement of the overall protection system, this thesis proposes a comprehensive and systematic methodology for the evaluation. The thesis also proposes a complete solution for the evaluation, in the form of a simulation environment. Finally, the thesis presents results of evaluation, along with their interpretation.

Naodovic, Bogdan

2005-05-01T23:59:59.000Z

200

Microprocessor systems and architectures for applications to the control and protection of electric power systems  

Science Conference Proceedings (OSTI)

Some design concepts for microprocessor applications to the control and protection of electric power systems are presented. A formal design methodology is outlined. Present microprocessor applications to the control and protection of the electric power ...

Dale I. Rummer; Mladen Kezunovic

1979-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Flooding and Fire Ants  

E-Print Network (OSTI)

Fire ants can be a serious problem during and after a flood. This publication explains how to protect yourself when you must return to flooded structures or deal with storm debris.

Nester, Paul

2008-08-05T23:59:59.000Z

202

A collision avoidance system for workpiece protection  

SciTech Connect

This paper describes an application of Sandia`s non-contact capacitive sensing technology for collision avoidance during the manufacturing of rocket engine thrust chambers. The collision avoidance system consists of an octagon shaped collar with a capacitive proximity sensor mounted on each face. The sensors produced electric fields which extend several inches from the face of the collar and detect potential collisions between the robot and the workpiece. A signal conditioning system processes the sensor output and provides varying voltage signals to the robot controller for stopping the robot.

Schmitt, D.J.; Weber, T.M.; Novak, J.L. [Sandia National Labs., Albuquerque, NM (United States); Maslakowski, J.E. [Rockwell International Corp., Canoga Park, CA (United States). Rocketdyne Div.

1995-04-01T23:59:59.000Z

203

Continuous Ammonia Slip Measurements on a Lignite-Fired Unit with a Selective Catalytic Reduction System  

Science Conference Proceedings (OSTI)

Ammonia slip measurements that were made by a tunable diode laser (TDL) were conducted on a lignite-fired unit with a selective catalytic reduction (SCR) system using a newly developed adjustable flange assembly for dynamic alignment of cross-duct measurements. The single path optics were integrated with a fiber optic–coupled TDL system (Unisearch LasIR) and two shields to allow measurements over the 25-foot (7.62-meter) flue gas duct dimension. The nominal 4.5-foot (1.67-meter) shields were required to ...

2011-10-24T23:59:59.000Z

204

Development of a high-performance coal-fired power generating system with pyrolysis gas and char-fired high temperature furnace (HITAF). Volume 1, Final report  

SciTech Connect

A major objective of the coal-fired high performance power systems (HIPPS) program is to achieve significant increases in the thermodynamic efficiency of coal use for electric power generation. Through increased efficiency, all airborne emissions can be decreased, including emissions of carbon dioxide. High Performance power systems as defined for this program are coal-fired, high efficiency systems where the combustion products from coal do not contact the gas turbine. Typically, this type of a system will involve some indirect heating of gas turbine inlet air and then topping combustion with a cleaner fuel. The topping combustion fuel can be natural gas or another relatively clean fuel. Fuel gas derived from coal is an acceptable fuel for the topping combustion. The ultimate goal for HIPPS is to, have a system that has 95 percent of its heat input from coal. Interim systems that have at least 65 percent heat input from coal are acceptable, but these systems are required to have a clear development path to a system that is 95 percent coal-fired. A three phase program has been planned for the development of HIPPS. Phase 1, reported herein, includes the development of a conceptual design for a commercial plant. Technical and economic feasibility have been analysed for this plant. Preliminary R&D on some aspects of the system were also done in Phase 1, and a Research, Development and Test plan was developed for Phase 2. Work in Phase 2 include s the testing and analysis that is required to develop the technology base for a prototype plant. This work includes pilot plant testing at a scale of around 50 MMBtu/hr heat input. The culmination of the Phase 2 effort will be a site-specific design and test plan for a prototype plant. Phase 3 is the construction and testing of this plant.

NONE

1996-02-01T23:59:59.000Z

205

Development of a numerical computer code and circuit element models for simulation of firing systems  

SciTech Connect

Numerical simulation of firing systems requires both the appropriate circuit analysis framework and the special element models required by the application. We have modified the SPICE circuit analysis code (version 2G.6), developed originally at the Electronic Research Laboratory of the University of California, Berkeley, to allow it to be used on MSDOS-based, personal computers and to give it two additional circuit elements needed by firing systems--fuses and saturating inductances. An interactive editor and a batch driver have been written to ease the use of the SPICE program by system designers, and the interactive graphical post processor, NUTMEG, supplied by U. C. Berkeley with SPICE version 3B1, has been interfaced to the output from the modified SPICE. Documentation and installation aids have been provided to make the total software system accessible to PC users. Sample problems show that the resulting code is in agreement with the FIRESET code on which the fuse model was based (with some modifications to the dynamics of scaling fuse parameters). In order to allow for more complex simulations of firing systems, studies have been made of additional special circuit elements--switches and ferrite cored inductances. A simple switch model has been investigated which promises to give at least a first approximation to the physical effects of a non ideal switch, and which can be added to the existing SPICE circuits without changing the SPICE code itself. The effect of fast rise time pulses on ferrites has been studied experimentally in order to provide a base for future modeling and incorporation of the dynamic effects of changes in core magnetization into the SPICE code. This report contains detailed accounts of the work on these topics performed during the period it covers, and has appendices listing all source code written documentation produced.

Carpenter, K.H. (Kansas State Univ., Manhattan, KS (USA). Dept. of Electrical and Computer Engineering)

1990-07-02T23:59:59.000Z

206

Heat Transfer and Thermophotovoltaic Power Generation in Oil-fired Heating Systems  

SciTech Connect

The focus of this study is the production of electric power in an oil-fired, residential heatingsystem using thermophotovoltaic (TPV) conversion devices. This work uses experimental, computational, and analytical methods to investigate thermal mechanisms that drive electric power production in the TPV systems. An objective of this work is to produce results that will lead to the development of systems that generate enough electricity such that the boiler is self-powering. An important design constraint employed in this investigation is the use of conventional, yellow-flame oil burners, integrated with a typical boiler. The power production target for the systems developed here is 100 W - the power requirement for a boiler that uses low-power auxiliary components. The important heattransfer coupling mechanisms that drive power production in the systems studied are discussed. The results of this work may lead to the development of systems that export power to the home electric system.

Butcher, T.; Hammonds, J.S.; Horne, E.; Kamath, B.; Carpenter, J.; Woods, D.R.

2010-10-21T23:59:59.000Z

207

Install Waste Heat Recovery Systems for Fuel-Fired Furnaces (English/Chinese) (Fact Sheet)  

SciTech Connect

Chinese translation of ITP fact sheet about installing Waste Heat Recovery Systems for Fuel-Fired Furnaces. For most fuel-fired heating equipment, a large amount of the heat supplied is wasted as exhaust or flue gases. In furnaces, air and fuel are mixed and burned to generate heat, some of which is transferred to the heating device and its load. When the heat transfer reaches its practical limit, the spent combustion gases are removed from the furnace via a flue or stack. At this point, these gases still hold considerable thermal energy. In many systems, this is the greatest single heat loss. The energy efficiency can often be increased by using waste heat gas recovery systems to capture and use some of the energy in the flue gas. For natural gas-based systems, the amount of heat contained in the flue gases as a percentage of the heat input in a heating system can be estimated by using Figure 1. Exhaust gas loss or waste heat depends on flue gas temperature and its mass flow, or in practical terms, excess air resulting from combustion air supply and air leakage into the furnace. The excess air can be estimated by measuring oxygen percentage in the flue gases.

Not Available

2011-10-01T23:59:59.000Z

208

Engineering Development of Coal-Fired High-Performance Power Systems  

Science Conference Proceedings (OSTI)

A High Performance Power System (HIPPS) is being developed. This system is a coal-fired, combined cycle plant with indirect heating of gas turbine air. Foster Wheeler Development Corporation and a team consisting of Foster Wheeler Energy Corporation, Bechtel Corporation, University of Tennessee Space Institute and Westinghouse Electric Corporation are developing this system. In Phase 1 of the project, a conceptual design of a commercial plant was developed. Technical and economic analyses indicated that the plant would meet the goals of the project which include a 47 percent efficiency (HHV) and a 10 percent lower cost of electricity than an equivalent size PC plant. The concept uses a pyrolysis process to convert coal into fuel gas and char. The char is fired in a High Temperature Advanced Furnace (HITAF). The HITAF is a pulverized fuel-fired boiler/air heater where steam is generated and gas turbine air is indirectly heated. The fuel gas generated in the pyrolyzer is then used to heat the gas turbine air further before it enters the gas turbine. The project is currently in Phase 2 which includes engineering analysis, laboratory testing and pilot plant testing. Research and development is being done on the HIPPS systems that are not commercial or being developed on other projects. Pilot plant testing of the pyrolyzer subsystem and the char combustion subsystem are being done separately. This report addresses the areas of technical progress for this quarter. The detail of syngas cooler design is given in this report. The final construction work of the CFB pyrolyzer pilot plant has started during this quarter. No experimental testing was performed during this quarter. The proposed test matrix for the future CFB pyrolyzer tests is given in this report. Besides testing various fuels, bed temperature will be the primary test parameter.

York Tsuo

2000-12-31T23:59:59.000Z

209

Protective, Modular Wave Power Generation System  

Science Conference Proceedings (OSTI)

The concept of small wave energy conversion modules that can be built into large, scalable arrays, in the same vein as solar panels, has been developed. This innovation lends itself to an organic business and development model, and enables the use of large-run manufacturing technology to reduce system costs. The first prototype module has been built to full-scale, and tested in a laboratory wave channel. The device has been shown to generate electricity and dissipate wave energy. Improvements need to be made to the electrical generator and a demonstration of an array of modules should be made in natural conditions.

Vvedensky, Jane M.; Park, Robert Y.

2012-11-27T23:59:59.000Z

210

Handling historical information on protected-area systems and coverage. An information system for the Natura 2000 European context  

Science Conference Proceedings (OSTI)

Protected-area coverage is an internationally-recognized surrogate indicator for measuring biodiversity conservation. To measure trends in biodiversity conservation over time, historical records on protected-area boundaries are needed. Protected-area ... Keywords: Biodiversity indicators, Conservation databases, Historical trends, Information systems (IS), Natura 2000, Protected areas, Protected-area boundaries, Protected-area coverage

Arnald Marcer; Víctor Garcia; Agustí Escobar; Xavier Pons

2010-08-01T23:59:59.000Z

211

Measurement of air toxic emissions from a coal-fired boiler equipped with a tangentially-fired low NOx combustion system  

Science Conference Proceedings (OSTI)

This paper presents the results of measurements of chemical emissions from a coal-burning, tangentially-fired, utility boiler equipped with a hot-side electrostatic precipitator and a low NOx firing system. The tests were conducted in response to Title III of the 1990 Amendments to the Clean Air Act which lists 189 chemicals to be evaluated as {open_quotes}Air Toxics.{close_quotes} The project was jointly funded by the Electric Power Research Institute and the US Department of Energy under an existing Innovative Clean Coal Technology Cooperative Agreement managed by Southern Company Services. Field chemical emissions monitoring was conducted in two phases: a baseline {open_quotes}pre-low NOx burner{close_quotes} condition in September 1991 and in the LNCFS Level III low NOx firing condition in January 1992. In addition to stack emissions measurements of both organic and inorganic chemicals, plant material balance evaluations were performed to determine the efficiency of the hot-side ESP at controlling emissions of air toxics and to determine the fate of the target chemicals in various plant process streams.

Dismukes, E.B. [Southern Research Inst., Birmingham, AL (United States); Clarkson, R.J.; Hardman, R.R. [Southern Company Services, Birmingham, AL (United States); Elia, G.G. [Pittsburgh Energy Technology Center, PA (United States)

1993-11-01T23:59:59.000Z

212

Assembly and Characterization of a Prototype Laser-Optical Firing System  

Science Conference Proceedings (OSTI)

The design, assembly and characterization of the latest generation of a small, ruggedized laser-optical firing system will be discussed. This work builds upon earlier results in an effort to continue the development of robust fiber-coupled laseroptical firing systems.[1][2] This newest prototype strives to improve on earlier designs, while continuing to utilize many of the environmentally proven opto-mechanical sub-assemblies.[2][3] One area of improvement involves the implementation of a second optical safing and arming component. Several additional design improvements were also incorporated to address shortcomings uncovered during environmental testing.[4][5] These tests and the subsequent failure analysis were performed at the laser sub-system level. Four identical prototypes were assembled and characterized. The performance of the units were evaluated by comparing a number of parameters including laser output energy, slope efficiency, beam divergence, spatial intensity profile, fiber injection and splitter-coupler transmission efficiency. Other factors evaluated were the ease of alignment, repeatability of the alignment process and the fabrication of the fiberoptical cables. The experimentally obtained results will be compared and contrasted to the performance of earlier prototypes.

Morelli, Gregg L

2009-08-03T23:59:59.000Z

213

Engineering development of advanced coal-fired low emission boil systems. Quarterly technical progress report, October 1993--December 1993  

Science Conference Proceedings (OSTI)

The first test run of the Toroidal Vortex Combustor (TVC) was completed on December 6. Riley was unable to witness or set up independent sampling equipment for NO{sub x} and precursor measurement for this run. A second run which we witnessed, but did not sample, was completed December 17. This was conducted almost entirely near SR = 1.0 while Textron investigated temperature-load relationships to address concerns from Run 1. A third run was completed over the December holiday break on Dorchester coal to address concerns Textron had about the Illinois test coal. All subsequent tests will use the Illinois coal. Boiler, firing system design. Elevation drawings were developed for dry wall-fired, conventional U-fired slagging, and TVC fired slagging units. We are investigating the feasibility of modifying a conventional U-fired design for low-NOx operation as an alternative to the TVC. The approach taken to I date for NOx reduction in existing U-fired units is to retrofit with delayed-mixing burners with staging air at various places, similar to the approach with dry fired units. The concept of staged fuel addition or reburning for the U-fired system is being examined as a potential combustion NOx control approach. This concept has high potential due to the high temperature and long residence time available in the stagger. Some field trials with coke oven gas reburn produced very low NOx results. Modeling of this concept was identified as a priority task. The model development will include matching field data for air staging on slagging units to the predictions. Emissions control. Selection of an SO2 control process continues to be a high priority task. Sargent & Lundy completed a cost comparison of several regenerable processes, most of which have NOx control potential as well: Active coke, NOXSO, copper oxide, SNOX, ammonia (for SO only, ammonium sulfate byproduct), and a limestone scrubber for comparison.

Not Available

1993-12-31T23:59:59.000Z

214

Development of a Data Management System for the Kuwait Oil Fire Atmospheric Measurement Program  

Science Conference Proceedings (OSTI)

Following the onset of the Kuwait oil fires in early 1991, numerous efforts to monitor and estimate the environmental effects of the fires were initiated. These efforts produced a diverse set of atmospheric data from airborne, surface-based, and ...

Julie A. Haggerty; Stephen P. Carley; David B. Johnson; Amy D. Michaelis

1994-10-01T23:59:59.000Z

215

Application of a Mini Unmanned Aircraft System for In Situ Monitoring of Fire Plume Thermodynamic Properties  

Science Conference Proceedings (OSTI)

Direct measurements of wildland fire plume properties are rare because of difficult access to regions near the fire front and plume. Moisture released from combustion, in addition to added heat, can enhance buoyancy and convection, influencing ...

Caroline M. Kiefer; Craig B. Clements; Brian E. Potter

2012-03-01T23:59:59.000Z

216

Software reliability and safety in nuclear reactor protection systems  

SciTech Connect

Planning the development, use and regulation of computer systems in nuclear reactor protection systems in such a way as to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Computer Safety and Reliability Group, Lawrence Livermore that investigates different aspects of computer software in reactor National Laboratory, that investigates different aspects of computer software in reactor protection systems. There are two central themes in the report, First, software considerations cannot be fully understood in isolation from computer hardware and application considerations. Second, the process of engineering reliability and safety into a computer system requires activities to be carried out throughout the software life cycle. The report discusses the many activities that can be carried out during the software life cycle to improve the safety and reliability of the resulting product. The viewpoint is primarily that of the assessor, or auditor.

Lawrence, J.D. [Lawrence Livermore National Lab., CA (United States)

1993-11-01T23:59:59.000Z

217

Container lid gasket protective strip for double door transfer system  

DOE Patents (OSTI)

An apparatus and a process for forming a protective barrier seal along a "ring of concern" of a transfer container used with double door systems is provided. A protective substrate is supplied between a "ring of concern" and a safety cover in which an adhesive layer of the substrate engages the "ring of concern". A compressive foam strip along an opposite side of the substrate engages a safety cover such that a compressive force is maintained between the "ring of concern" and the adhesive layer of the substrate.

Allen, Jr., Burgess M

2013-02-19T23:59:59.000Z

218

Personnel Protection Systems for Electric Vehicle Charging Circuits  

Science Conference Proceedings (OSTI)

Electric vehicle charging systems will be required to provide protection against electric shock due to ground faults. This report reviews the subject of electric shock, including the effects of current magnitude, frequency, duration, alternating and direct current, and supply voltage to ground. The report suggests a basis for specific safety requirements--such as a ground fault circuit interrupt--that can be included in a product safety standard covering electric vehicle charging systems to meet the 1996...

2000-01-05T23:59:59.000Z

219

The low moisture eastern coal processing system at the UTSI-DOE Coal Fired Flow Facility  

DOE Green Energy (OSTI)

A low moisture, eastern coal processing system was constructed at the Department of Energy`s Coal Fired Flow Facility (CFFF), located at the University of Tennessee Space Institute in Tullahoma, Tennessee, to provide a metered and regulated supply of seeded, pulverized coal to support magnetohydrodynamic (MHD) power generation research. The original system configuration is described as well as major modifications made in response to specific operational problems. Notable among these was the in-house development of the Moulder flow control valve which exhibited marked improvement in durability compared to previous valves used with pulverized coal. Coal processing system performance parameters are discussed. A summary of tests conducted and significant events are included.

Evans, B.R.; Washington, E.S.; Sanders, M.E.

1993-10-01T23:59:59.000Z

220

Engineering Development of Coal-Fired High-Performance Power Systems  

SciTech Connect

A High Performance Power System (HIPPS) is being developed. This system is a coal-fired, combined cycle plant with indirect heating of gas turbine air. Foster Wheeler Development Corporation and a team consisting of Foster Wheeler Energy Corporation, Bechtel Corporation, University of Tennessee Space Institute and Westinghouse Electric Corporation are developing this system. In Phase 1 of the project, a conceptual design of a commercial plant was developed. Technical and economic analyses indicated that the plant would meet the goals of the project which include a 47 percent efficiency (HHV) and a 10 percent lower cost of electricity than an equivalent size PC plant. The concept uses a pyrolysis process to convert coal into fuel gas and char. The char is fired in a High Temperature Advanced Furnace (HITAF). The HITAF is a pulverized fuel-fired boiler/air heater where steam is generated and gas turbine air is indirectly heated. The fuel gas generated in the pyrolyzer is then used to heat the gas turbine air further before it enters the gas turbine. The project is currently in Phase 2 which includes engineering analysis, laboratory testing and pilot plant testing. Research and development is being done on the HIPPS systems that are not commercial or being developed on other projects. Pilot plant testing of the pyrolyzer subsystem and the char combustion subsystem are being done separately, and after each experimental program has been completed, a larger scale pyrolyzer will be tested at the Power Systems Development Facility (PSDF) in Wilsonville, AL. The facility is equipped with a gas turbine and a topping combustor, and as such, will provide an opportunity to evaluate integrated pyrolyzer and turbine operation. This report addresses the areas of technical progress for this quarter. Detailed design of the components to be used to for the circulating bed gasification tests is underway. The circulating fluidized bed will allow for easy scale-up to larger size plants. The existing pyrolyzer will be outfitted with a cyclone and a j-valve to capture and reinject char into the lower combustion zone. Additional development work has been performed to evaluate advanced cycles utilizing the HIPPS system concept.

York Tsuo

1999-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Fire Suppression in Aircraft  

Science Conference Proceedings (OSTI)

... Imperial Japanese Navy Dry Bay and Ullage Fire Suppression System Concept ... Calibration Plot of Average Normalized Peak-to-valley Signals vs. ...

2011-12-27T23:59:59.000Z

222

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Proceedings. October 15-17, 2008, Poznan, Poland, 1-8 pp, 2008. Domanski, PA; Yashar, DA; Kaufman, K. Fire Alarm Systems. ...

223

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Proceedings. October 15-17, 2008, Poznan, Poland, 1-8 pp, 2008. Domanski, PA; Yashar, DA; Kaufman, K. Fire Alarm Signaling Systems. ...

224

Fire modeling programs  

Science Conference Proceedings (OSTI)

... state pressures and flows throughout the building. ... environment, and fire energy release rates ... fan/duct forced ventilation systems between arbitrary ...

2013-04-24T23:59:59.000Z

225

Building and Fire Publications  

Science Conference Proceedings (OSTI)

At the 1968 ASHRAE Annual Meeting in Lake Placid, New York, the symposium 'Fire Hazards in Buildings and Air-Handling Systems' was held. ...

226

Fire hazard analysis of Rocky Flats Building 776/777 duct systems  

SciTech Connect

The objective of this analysis is to determine if ventilation ductwork in Building 776/777 will maintain their structural integrity during expected fire conditions as well as standard design fires typically used to ascertain fire resistance ratings. If the analysis shows that ductwork will not maintain structural integrity, the impact of this failure will be determined and analyzed, and alternative solutions recommended. Associated with this analysis is the development of a computer fire model which can be used as an engineering tool in analyzing the effect of fires on ductwork in other areas and buildings.

DiNenno, P.J.; Scheffey, J.L.; Gewain, R.G.; Shanley, J.H. Jr. [Hughes Associates, Inc., Wheaton, MD (United States)

1988-12-01T23:59:59.000Z

227

Hybrid Plasma Reactor/Filter for Transportable Collective Protection Systems  

SciTech Connect

Pacific Northwest National Laboratory (PNNL) has performed an assessment of a Hybrid Plasma/Filter system as an alternative to conventional methods for collective protection. The key premise of the hybrid system is to couple a nonthermal plasma (NTP) reactor with reactive adsorption to provide a broader envelope of protection than can be provided through a single-solution approach. The first step uses highly reactive species (e.g. oxygen radicals, hydroxyl radicals, etc.) created in a nonthermal plasma (NTP) reactor to destroy the majority (~75% - 90%) of an incoming threat. Following the NTP reactor an O3 reactor/filter uses the O3 created in the NTP reactor to further destroy the remaining organic materials. This report summarizes the laboratory development of the Hybrid Plasma Reactor/Filter to protect against a ‘worst-case’ simulant, methyl bromide (CH3Br), and presents a preliminary engineering assessment of the technology to Joint Expeditionary Collective Protection performance specifications for chemical vapor air purification technologies.

Josephson, Gary B.; Tonkyn, Russell G.; Frye, J. G.; Riley, Brian J.; Rappe, Kenneth G.

2011-04-06T23:59:59.000Z

228

Advanced Control and Protection system Design Methods for Modular HTGRs  

DOE Green Energy (OSTI)

The project supported the Nuclear Regulatory Commission (NRC) in identifying and evaluating the regulatory implications concerning the control and protection systems proposed for use in the Department of Energy's (DOE) Next-Generation Nuclear Plant (NGNP). The NGNP, using modular high-temperature gas-cooled reactor (HTGR) technology, is to provide commercial industries with electricity and high-temperature process heat for industrial processes such as hydrogen production. Process heat temperatures range from 700 to 950 C, and for the upper range of these operation temperatures, the modular HTGR is sometimes referred to as the Very High Temperature Reactor or VHTR. Initial NGNP designs are for operation in the lower temperature range. The defining safety characteristic of the modular HTGR is that its primary defense against serious accidents is to be achieved through its inherent properties of the fuel and core. Because of its strong negative temperature coefficient of reactivity and the capability of the fuel to withstand high temperatures, fast-acting active safety systems or prompt operator actions should not be required to prevent significant fuel failure and fission product release. The plant is designed such that its inherent features should provide adequate protection despite operational errors or equipment failure. Figure 1 shows an example modular HTGR layout (prismatic core version), where its inlet coolant enters the reactor vessel at the bottom, traversing up the sides to the top plenum, down-flow through an annular core, and exiting from the lower plenum (hot duct). This research provided NRC staff with (a) insights and knowledge about the control and protection systems for the NGNP and VHTR, (b) information on the technologies/approaches under consideration for use in the reactor and process heat applications, (c) guidelines for the design of highly integrated control rooms, (d) consideration for modeling of control and protection system designs for VHTR, and (e) input for developing the bases for possible new regulatory guidance to assist in the review of an NGNP license application. This NRC project also evaluated reactor and process heat application plant simulation models employed in the protection and control system designs for various plant operational modes and accidents, including providing information about the models themselves, and the appropriateness of the application of the models for control and protection system studies. A companion project for the NRC focused on the potential for new instrumentation that would be unique to modular HTGRs, as compared to light-water reactors (LWRs), due to both the higher temperature ranges and the inherent safety features.

Ball, Sydney J [ORNL; Wilson Jr, Thomas L [ORNL; Wood, Richard Thomas [ORNL

2012-06-01T23:59:59.000Z

229

Idaho National Engineering and Environmental Laboratory Wildland Fire Management Environmental Assessment - April 2003  

SciTech Connect

DOE prepared an environmental assessment (EA)for wildland fire management activities on the Idaho National Engineering and Environmental Laboratory (INEEL) (DOE/EA-1372). The EA was developed to evaluate wildland fire management options for pre-fire, fire suppression, and post fire activities. Those activities have an important role in minimizing the conversion of the native sagebrush steppe ecosystem found on the INEEL to non-native weeds. Four alternative management approaches were analyzed: Alternative 1 - maximum fire protection; Alternative 2 - balanced fire protection; Alternative 2 - balanced fire protection; Alternative 3 - protect infrastructure and personnel; and Alternative 4 - no action/traditional fire protection.

Irving, J.S.

2003-04-30T23:59:59.000Z

230

Idaho National Engineering and Environmental Laboratory Wildland Fire Management Environmental Assessment  

SciTech Connect

DOE prepared an environmental assessment (EA)for wildland fire management activities on the Idaho National Engineering and Environmental Laboratory (INEEL) (DOE/EA-1372). The EA was developed to evaluate wildland fire management options for pre-fire, fire suppression, and post fire activities. Those activities have an important role in minimizing the conversion of the native sagebrush steppe ecosystem found on the INEEL to non-native weeds. Four alternative management approaches were analyzed: Alternative 1 - maximum fire protection; Alternative 2 - balanced fire protection; Alternative 2 - balanced fire protection; Alternative 3 - protect infrastructure and personnel; and Alternative 4 - no action/traditional fire protection.

Irving, John S

2003-04-01T23:59:59.000Z

231

Evaluation of Authorization Basis Management Systems and Processes...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

plant priorities contributes to deferral of needed plant infrastructure upgrades, such as roof replacements and fire protection system improvements. Pantex line managers also...

232

Fire Dynamics  

Science Conference Proceedings (OSTI)

... is the rate at which fire releases energy - this is also known as power. ... fuel) to enable the completion of the fire triangle and the generation of energy ...

2013-07-16T23:59:59.000Z

233

Comparison of Control System Performance for Fossil-Fuel Fired Power Plants Using Emission Measurement Data from the Utility Industr y Information Collection Request for Hazardous Air Pollutants  

Science Conference Proceedings (OSTI)

On On May 3, 2011, the U.S. Environmental Protection Agency (EPA) published a notice of proposed rulemaking (40 Code of Federal Regulations Parts 60 and 63: National Emission Standards for Hazardous Air Pollutants from Coal- and Oil-Fired Electric Utility Steam Generating Units and Standards of Performance for Fossil-FuelFired Electric Utility, Industrial-Commercial-Institutional, and Small Industrial-Commercial-Institutional Steam-Generating Units). The intent of this rulemaking is to set Maximum Achiev...

2011-12-23T23:59:59.000Z

234

Promising freeze protection alternatives in solar domestic hot water systems  

DOE Green Energy (OSTI)

Since the gains associated with solar thermal energy technologies are comparatively small in relation to the required capital investment, it is vital to maximize conversion efficiency. While providing the necessary function of freeze protection, the heat exchanger commonly included in solar domestic water heating systems represents a system inefficiency. This thesis explores two alternate methods of providing freeze protection without resorting to a heat exchanger. Commonly, collectors are made of rigid copper tubes separated by copper or aluminum fins. Cracking damage can occur when water is allowed to freeze and expand inside the non compliant tubes. The possibility of making collectors out of an elastic material was investigated and shown to be effective. Since unlike copper, elastomers typically have low thermal conductivities, the standard collector performance prediction equations do not apply. Modified thermal performance prediction equations were developed which can be used for both low and high thermal conductivity materials to provide accurate predictions within a limited range of plate geometries. An elastomeric collector plate was then designed and shown to have comparable performance to a copper plate collector whose aperture area is approximately 33% smaller. Another options for providing freeze protection to an SDHW system is to turn it off during the winter. Choosing a three-season operating period means two things. First, the system will have different optimums such as slope and collector area. Second, the wintertime solar energy incident on the collector is unavailable for meeting a heating load. However, the system`s heat exchanger becomes unnecessary and removing it increases the amount of energy that arrives at the storage tank during those periods in which the system is operating.

Bradley, D.E.

1997-12-31T23:59:59.000Z

235

Fire Fighting Technology  

Science Conference Proceedings (OSTI)

... prevention and control of fires to enhance fire fighting operations and equipment, fire suppression, fire investigations, and disaster response. ...

2013-07-16T23:59:59.000Z

236

Fire Fighting Technology Group  

Science Conference Proceedings (OSTI)

... prevention and control of fires to enhance fire fighting operations and equipment, fire suppression, fire investigations, and disaster response. ...

2013-12-19T23:59:59.000Z

237

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... sprinklers; egress; fire spread; fire models; polyurethane foams; pyrotechnics; smoke; insulation; death; fire fatalities; building codes; fire codes ...

238

Modeling of integrated environmental control systems for coal-fired power plants  

SciTech Connect

The Integrated Environmental Control Model (IECM) was designed to permit the systematic evaluation of environmental control options for pulverized coal-fired (PC) power plants. Of special interest was the ability to compare the performance and cost of advanced pollution control systems to conventional'' technologies for the control of particulate, SO{sub 2} and NO{sub x}. Of importance also was the ability to consider pre-combustion, combustion and post-combustion control methods employed alone or in combination to meet tough air pollution emission standards. Finally, the ability to conduct probabilistic analyses is a unique capability of the IECM. Key results are characterized as distribution functions rather than as single deterministic values. (VC)

Rubin, E.S.; Salmento, J.S.; Frey, H.C.; Abu-Baker, A.; Berkenpas, M.

1991-05-01T23:59:59.000Z

239

Modeling of integrated environmental control systems for coal-fired power plants. Final report  

SciTech Connect

The Integrated Environmental Control Model (IECM) was designed to permit the systematic evaluation of environmental control options for pulverized coal-fired (PC) power plants. Of special interest was the ability to compare the performance and cost of advanced pollution control systems to ``conventional`` technologies for the control of particulate, SO{sub 2} and NO{sub x}. Of importance also was the ability to consider pre-combustion, combustion and post-combustion control methods employed alone or in combination to meet tough air pollution emission standards. Finally, the ability to conduct probabilistic analyses is a unique capability of the IECM. Key results are characterized as distribution functions rather than as single deterministic values. (VC)

Rubin, E.S.; Salmento, J.S.; Frey, H.C.; Abu-Baker, A.; Berkenpas, M.

1991-05-01T23:59:59.000Z

240

System design verification of a hybrid geothermal/coal fired power plant  

DOE Green Energy (OSTI)

This hybrid plant utilizes geothermal fluid for feedwater heating. With respect to the extraction of available work from the geothermal fluids, this cycle is approximately two times as efficient as the all geothermal plant. The System Design Verification Study presented verifies the technical and economic feasibility of the hybrid plant. This report is comprised of a conceptual design, cost estimate, and economic analysis of a one-unit 715 MW hybrid geothermal/coal fired power plant. In addition to the use of geothermal fluid for feedwater heating, its use is also investigated for additional power generation, condensate and cooling tower makeup water, coal beneficiation, air preheating, flue gas reheating and plant space heating requirements. An engineering and construction schedule for the hybrid plant is also included.

Not Available

1978-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Development of a high-performance coal-fired power generating system with pyrolysis gas and char-fired high-temperature furnace (HITAF): Volume 4. Final report  

Science Conference Proceedings (OSTI)

An outgrowth of our studies of the FWDC coal-fired high performance power systems (HIPPS) concept was the development of a concept for the repowering of existing boilers. The initial analysis of this concept indicates that it will be both technically and economically viable. A unique feature of our greenfields HIPPS concept is that it integrates the operation of a pressurized pyrolyzer and a pulverized fuel-fired boiler/air heater. Once this type of operation is achieved, there are a few different applications of this core technology. Two greenfields plant options are the base case plant and a plant where ceramic air heaters are used to extend the limit of air heating in the HITAF. The greenfields designs can be used for repowering in the conventional sense which involves replacing almost everything in the plant except the steam turbine and accessories. Another option is to keep the existing boiler and add a pyrolyzer and gas turbine to the plant. The study was done on an Eastern utility plant. The owner is currently considering replacing two units with atmospheric fluidized bed boilers, but is interested in a comparison with HIPPS technology. After repowering, the emissions levels need to be 0.25 lb SO{sub x}/MMBtu and 0.15 lb NO{sub x}/MMBtu.

NONE

1996-05-01T23:59:59.000Z

242

Emergency Response Training Complex Brayton Fire Training ...  

Science Conference Proceedings (OSTI)

... 40 Communication Tower I - Cylinder Tanks 123 Breaching ... 45 API Storage Tank Fires 82 Marine Ship ... 52 Sprinkler Systems 88 LNG Fires / Auto ...

2006-02-17T23:59:59.000Z

243

An assessment of fire vulnerability for aged electrical relays  

SciTech Connect

There has been some concern that, as nuclear power plants age, protective measures taken to control and minimize the impact of fire may become ineffective, or significantly less effective, and hence result in an increased fire risk. One objective of the Fire Vulnerability of Aged Electrical Components Program is to assess the effects of aging and service wear on the fire vulnerability of electrical equipment. An increased fire vulnerability of components may lead to an overall increase in fire risk to the plant. Because of their widespread use in various electrical safety systems, electromechanical relays were chosen to be the initial components for evaluation. This test program assessed the impact of operational and thermal aging on the vulnerability of these relays to fire-induced damage. Only thermal effects of a fire were examined in this test program. The impact of smoke, corrosive materials, or fire suppression effects on relay performance were not addressed in this test program. The purpose of this test program was to assess whether the fire vulnerability of electrical relays increased with aging. The sequence followed for the test program was to: identify specific relay types, develop three fire scenarios, artificially age several relays, test the unaged and aged relays in the fire exposure scenarios, and compare the results. The relays tested were Agastat GPI, General Electric (GE) HMA, HGA, and HFA. At least two relays of each type were artificially aged and at least two relays of each type were new. Relays were operationally aged by cycling the relay under rated load for 2,000 operations. These relays were then thermally aged for 60 days with their coil energized.

Vigil, R.A. [Sandia National Labs., Albuquerque, NM (United States)]|[Science and Engineering Associates, Inc., Albuquerque, NM (United States); Nowlen, S.P. [Sandia National Labs., Albuquerque, NM (United States)

1995-03-01T23:59:59.000Z

244

Review of the Los Alamos National Laboratory Waste Characterization, Reduction, and Repackaging Facility Fire Suppression System, January 2012  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste Waste Characterization, Reduction, and Repackaging Facility Fire Suppression System January 2012 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy i Table of Contents 1.0 Purpose ................................................................................................................................................... 1 2.0 Background ............................................................................................................................................ 1 3.0 Scope ...................................................................................................................................................... 1

245

Review of the Los Alamos National Laboratory Waste Characterization, Reduction, and Repackaging Facility Fire Suppression System, January 2012  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Waste Waste Characterization, Reduction, and Repackaging Facility Fire Suppression System January 2012 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy i Table of Contents 1.0 Purpose ................................................................................................................................................... 1 2.0 Background ............................................................................................................................................ 1 3.0 Scope ...................................................................................................................................................... 1

246

Review of the Los Alamos National Laboratory Chemistry and Metallurgy Research Facility Fire Suppression Vital Safety System, January 2012  

NLE Websites -- All DOE Office Websites (Extended Search)

the the Los Alamos National Laboratory Chemistry and Metallurgy Research Facility Fire Suppression Vital Safety System January 2012 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy i Table of Contents 1.0 Purpose ................................................................................................................................................... 1 2.0 Background ............................................................................................................................................ 1 3.0 Scope ...................................................................................................................................................... 1

247

Review of the Los Alamos National Laboratory Chemistry and Metallurgy Research Facility Fire Suppression Vital Safety System, January 2012  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

the the Los Alamos National Laboratory Chemistry and Metallurgy Research Facility Fire Suppression Vital Safety System January 2012 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy i Table of Contents 1.0 Purpose ................................................................................................................................................... 1 2.0 Background ............................................................................................................................................ 1 3.0 Scope ...................................................................................................................................................... 1

248

Estimation of radiative properties and temperature distributions in coal-fired boiler furnaces by a portable image processing system  

Science Conference Proceedings (OSTI)

This paper presented an experimental investigation on the estimation of radiative properties and temperature distributions in a 670 t/h coal-fired boiler furnace by a portable imaging processing system. The portable system has been calibrated by a blackbody furnace. Flame temperatures and emissivities were measured by the portable system and equivalent blackbody temperatures were deduced. Comparing the equivalent blackbody temperatures measured by the portable system and the infrared pyrometer, the relative difference is less than 4%. The reconstructed pseudo-instantaneous 2-D temperature distributions in two cross-sections can disclose the combustion status inside the furnace. The measured radiative properties of particles in the furnace proved there is significant scattering in coal-fired boiler furnaces and it can provide useful information for the calculation of radiative heat transfer and numerical simulation of combustion in coal-fired boiler furnaces. The preliminary experimental results show this technology will be helpful for the combustion diagnosis in coal-fired boiler furnaces. (author)

Li, Wenhao; Lou, Chun; Sun, Yipeng; Zhou, Huaichun [State Key Laboratory of Coal Combustion, Huazhong University of Science and Technology, Wuhan, 430074 Hubei (China)

2011-02-15T23:59:59.000Z

249

Independent Oversight Review of the Technical Area 55 Safety Class Fire Suppression System at Los Alamos National Laboratory, December 2013  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technical Area 55 Technical Area 55 Safety Class Fire Suppression System at Los Alamos National Laboratory December 2013 Office of Safety and Emergency Management Evaluations Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy Table of Contents 1.0 Purpose .................................................................................................................................................... 1 2.0 Background ............................................................................................................................................. 1 3.0 Scope ....................................................................................................................................................... 2

250

NISTIR 6299 A Heat Transfer Model for Fire Fighter's ...  

Science Conference Proceedings (OSTI)

Page 1. NISTIR 6299 A Heat Transfer Model for Fire Fighter's Protective Clothing William E. Mell J. Randall Lawson United ...

1999-05-06T23:59:59.000Z

251

Development and Testing of Industrial Scale Coal Fired Combustion System, Phase 3  

SciTech Connect

Coal Tech Corp's mission is to develop, license & sell innovative, lowest cost, solid fuel fired power systems & total emission control processes using proprietary and patented technology for domestic and international markets. The present project 'DEVELOPMENT & TESTING OF INDUSTRIAL SCALE, COAL FIRED COMBUSTION SYSTEM, PHASE 3' on DOE Contract DE-AC22-91PC91162 was a key element in achieving this objective. The project consisted of five tasks that were divided into three phases. The first phase, 'Optimization of First Generation 20 MMBtu/hr Air-Cooled Slagging Coal Tech Combustor', consisted of three tasks, which are detailed in Appendix 'A' of this report. They were implemented in 1992 and 1993 at the first generation, 20 MMBtu/hour, combustor-boiler test site in Williamsport, PA. It consisted of substantial combustor modifications and coal-fired tests designed to improve the combustor's wall cooling, slag and ash management, automating of its operation, and correcting severe deficiencies in the coal feeding to the combustor. The need for these changes was indicated during the prior 900-hour test effort on this combustor that was conducted as part of the DOE Clean Coal Program. A combination of combustor changes, auxiliary equipment changes, sophisticated multi-dimensional combustion analysis, computer controlled automation, and series of single and double day shift tests totaling about 300 hours, either resolved these operational issues or indicated that further corrective changes were needed in the combustor design. The key result from both analyses and tests was that the combustor must be substantially lengthened to maximize combustion efficiency and sharply increase slag retention in the combustor. A measure of the success of these modifications was realized in the third phase of this project, consisting of task 5 entitled: 'Site Demonstration with the Second Generation 20 MMBtu/hr Air-Cooled Slagging Coal Tech Combustor'. The details of the task 5 effort are contained in Appendix 'C'. It was implemented between 1994 and 1998 after the entire 20 MMBtu/hr combustor-boiler facility was relocated to Philadelphia, PA in 1994. A new test facility was designed and installed. A substantially longer combustor was fabricated. Although not in the project plan or cost plan, an entire steam turbine-electric power generating plant was designed and the appropriate new and used equipment for continuous operation was specified. Insufficient funds and the lack of a customer for any electric power that the test facility could have generated prevented the installation of the power generating equipment needed for continuous operation. All other task 5 project measures were met and exceeded. 107 days of testing in task 5, which exceeded the 63 days (about 500 hours) in the test plan, were implemented. Compared to the first generation 20 MMBtu/hr combustor in Williamsport, the 2nd generation combustor has a much higher combustion efficiency, the retention of slag inside the combustor doubled to about 75% of the coal ash, and the ash carryover into the boiler, a major problem in the Williamsport combustor was essentially eliminated. In addition, the project goals for coal-fired emissions were exceeded in task 5. SO{sub 2} was reduced by 80% to 0.2 lb/MMBtu in a combination of reagent injection in the combustion and post-combustion zones. NO{sub x} was reduced by 93% to 0.07 lb/MMBtu in a combination of staged combustion in the combustor and post-combustion reagent injection. A baghouse was installed that was rated to 0.03 lb/MMBtu stack particle emissions. The initial particle emission test by EPA Method 5 indicated substantially higher emissions far beyond that indicated by the clear emission plume. These emissions were attributed to steel particles released by wall corrosion in the baghouse, correction of which had no effect of emissions.

Bert Zauderer

1998-09-30T23:59:59.000Z

252

The high moisture western coal processing system at the UTSI-DOE Coal Fired Flow Facility. Topical report  

DOE Green Energy (OSTI)

The original eastern coal processing system at the Department of Energy`s Coal Fired Flow Facility (CFFF), located at the University of Tennessee Space Institute in Tullahoma, Tennessee, was modified to pulverize and dry Montana Rosebud, a western coal. Significant modifications to the CFFF coal processing system were required and the equipment selection criteria are reviewed. Coal processing system performance parameters are discussed. A summary of tests conducted and significant events are included.

Sanders, M.E.

1996-02-01T23:59:59.000Z

253

System Modeling of ORNL s 20 MW(t) Wood-fired Gasifying Boiler  

Science Conference Proceedings (OSTI)

We present an overview of the new 20 MW(t) wood-fired steam plant currently under construction by Johnson Controls, Inc. at the Oak Ridge National Laboratory in Tennessee. The new plant will utilize a low-temperature air-blown gasifier system developed by the Nexterra Systems Corporation to generate low-heating value syngas (producer gas), which will then be burned in a staged combustion chamber to produce heat for the boiler. This is considered a showcase project for demonstrating the benefits of clean, bio-based energy, and thus there is considerable interest in monitoring and modeling the energy efficiency and environmental footprint of this technology relative to conventional steam generation with petroleum-based fuels. In preparation for system startup in 2012, we are developing steady-state and dynamic models of the major process components, including the gasifiers and combustor. These tools are intended to assist in tracking and optimizing system performance and for carrying out future conceptual studies of process changes that might improve the overall energy efficiency and sustainability. In this paper we describe the status of our steady-state gasifier and combustor models and illustrate preliminary results from limited parametric studies.

Daw, C Stuart [ORNL; FINNEY, Charles E A [ORNL; Wiggins, Gavin [ORNL; Hao, Ye [ORNL

2010-01-01T23:59:59.000Z

254

Water Consumption from Freeze Protection Valves for Solar Water Heating Systems  

DOE Green Energy (OSTI)

Conference paper regarding research in the use of freeze protection valves for solar domestic water heating systems in cold climates.

Burch, J.; Salasovich, J.

2005-12-01T23:59:59.000Z

255

Digital protection systems response to sequence and phase components in non sinusoidal operation conditions  

Science Conference Proceedings (OSTI)

Traditional open literature about protection systems documents the use of residual currents or voltages (zero sequence components) and negative sequence components of currents or voltages to detect and protect the different power system elements against ... Keywords: digital protection systems, harmonic distortion, negative sequence, non sinusoidal operation, phase components, zero sequence

F. Martínez-Cárdenas; A. Medina

2006-11-01T23:59:59.000Z

256

The Impact of Protection System Failures on Power System Reliability Evaluation  

E-Print Network (OSTI)

The reliability of protection systems has emerged as an important topic because protection failures have critical influence on the reliability of power systems. The goal of this research is to develop novel approaches for modeling and analysis of the impact of protection system failures on power system reliability. It is shown that repairable and non-repairable assumptions make a remarkable difference in reliability modeling. A typical all-digital protection system architecture is modeled and numerically analyzed. If an all-digital protection system is indeed repairable but is modeled in a non-repairable manner for analysis, the calculated values of reliability indices could be grossly pessimistic. The smart grid is emerging with the penetration of information-age technologies and the development of the Special Protection System (SPS) will be greatly influenced. A conceptual all-digital SPS architecture is proposed for the future smart grid. Calculation of important reliability indices by the network reduction method and the Markov modeling method is illustrated in detail. Two different Markov models are proposed for reliability evaluation of the 2-out-of-3 voting gates structure in a generation rejection scheme. If the model with consideration of both detectable and undetectable logic gate failures is used as a benchmark, the simple model which only considers detectable failures will significantly overestimate the reliability of the 2-out-of-3 voting gates structure. The two types of protection failures, undesired-tripping mode and fail-to-operate mode are discussed. A complete Markov model for current-carrying components is established and its simplified form is then derived. The simplified model can appropriately describe the overall reliability situation of individual components under the circumstances of complex interactions between components due to protection failures. New concepts of the self-down state and the induced-down state are introduced and utilized to build up the composite unit model. Finally, a two-layer Markov model for power systems with protection failures is proposed. It can quantify the impact of protection failures on power system reliability. Using the developed methodology, we can see that the assumption of perfectly reliable protection can introduce errors in reliability evaluation of power systems.

Jiang, Kai

2012-12-01T23:59:59.000Z

257

EVALUATION OF MERCURY EMISSIONS FROM COAL-FIRED FACILITIES WITH SCR AND FGD SYSTEMS  

Science Conference Proceedings (OSTI)

CONSOL Energy Inc., Research & Development (CONSOL), with support from the U.S. Department of Energy, National Energy Technology Laboratory (DOE) is evaluating the effects of selective catalytic reduction (SCR) on mercury (Hg) capture in coal-fired plants equipped with an electrostatic precipitator (ESP) - wet flue gas desulfurization (FGD) combination or a spray dyer absorber--fabric filter (SDA-FF) combination. In this program CONSOL is determining mercury speciation and removal at 10 coal-fired facilities. The objectives are (1) to evaluate the effect of SCR on mercury capture in the ESP-FGD and SDA-FF combinations at coal-fired power plants, (2) evaluate the effect of catalyst degradation on mercury capture; (3) evaluate the effect of low load operation on mercury capture in an SCR-FGD system, and (4) collect data that could provide the basis for fundamental scientific insights into the nature of mercury chemistry in flue gas, the catalytic effect of SCR systems on Hg speciation and the efficacy of different FGD technologies for Hg capture. This document, the second in a series of topical reports, describes the results and analysis of mercury sampling performed on a 330 MW unit burning a bituminous coal containing 1.0% sulfur. The unit is equipped with a SCR system for NOx control and a spray dryer absorber for SO{sub 2} control followed by a baghouse unit for particulate emissions control. Four sampling tests were performed in March 2003. Flue gas mercury speciation and concentrations were determined at the SCR inlet, air heater outlet (ESP inlet), and at the stack (FGD outlet) using the Ontario Hydro method. Process stream samples for a mercury balance were collected to coincide with the flue gas measurements. Due to mechanical problems with the boiler feed water pumps, the actual gross output was between 195 and 221 MW during the tests. The results showed that the SCR/air heater combination oxidized nearly 95% of the elemental mercury. Mercury removal, on a coal-to-stack basis, was 87%. The mercury material balance closures for the four tests conducted at the plant ranged from 89% to 114%, with an average of 100%. These results appear to show that the SCR had a positive effect on mercury removal. In earlier programs, CONSOL sampled mercury at six plants with wet FGDs for SO{sub 2} control without SCR catalysts. At those plants, an average of 61 {+-} 15% of the mercury was in the oxidized form at the air heater outlet. The principal purpose of this work is to develop a better understanding of the potential Hg removal ''co-benefits'' achieved by NOx, and SO{sub 2} control technologies. It is expected that this data will provide the basis for fundamental scientific insights into the nature of Hg chemistry in flue gas, the catalytic effect of SCR systems on Hg speciation and the efficacy of different FGD technologies for Hg capture. Ultimately, this insight could help to design and operate SCR and FGD systems to maximize Hg removal.

J. A. Withum; S.C. Tseng; J. E. Locke

2004-10-31T23:59:59.000Z

258

FIRE SUPPRESSION IN COLD CLIMATES: A TECHNICAL ...  

Science Conference Proceedings (OSTI)

... from crude oil, coupled with an ignition source such as static electricity or a ... the Central Power Station for local fire protection in the turbine hoods of ...

2011-10-13T23:59:59.000Z

259

Project: High Temperature Performance of Fire Fighter ...  

Science Conference Proceedings (OSTI)

... Nazare, S., Davis, R., Peng, J., and Chin, J. Accelerated Weathering of Fire Fighter Protective Clothing: Delineating the Impact ... Facilities/Tools Used ...

2012-12-27T23:59:59.000Z

260

Protective Coatings Assessment  

Science Conference Proceedings (OSTI)

It is well known that fireside corrosion of waterwall panels in coal-fired boilers increased with the introduction of low NOx combustion systems since the early 1980s. This report describes ongoing work to evaluate protective coating solutions used to mitigate the wastage due to corrosion, and to determine which provide the greatest resistance to the circumferential cracking phenomena. It includes recent laboratory corrosion assisted thermal fatigue tests and analyses of field-exposed samples of ...

2012-12-17T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Evaluation of Mercury Emissions from Coal-Fired Facilities with SCR and FGD Systems  

Science Conference Proceedings (OSTI)

CONSOL Energy Inc., Research & Development (CONSOL), with support from the U.S. Department of Energy, National Energy Technology Laboratory (DOE) and the Electric Power Research Institute (EPRI), is evaluating the effects of selective catalytic reduction (SCR) on mercury (Hg) capture in coal-fired plants equipped with an electrostatic precipitator (ESP)--wet flue gas desulfurization (FGD) combination or a spray dyer absorber--fabric filter (SDA-FF) combination. In this program CONSOL is determining mercury speciation and removal at 10 coal-fired facilities. The principal purpose of this work is to develop a better understanding of the potential mercury removal ''co-benefits'' achieved by NO{sub x}, and SO{sub 2} control technologies. It is expected that these data will provide the basis for fundamental scientific insights into the nature of mercury chemistry in flue gas, the catalytic effect of SCR systems on mercury speciation and the efficacy of different FGD technologies for mercury capture. Ultimately, this insight could help to design and operate SCR and FGD systems to maximize mercury removal. The objectives are (1) to evaluate the effect of SCR on mercury capture in the ESP-FGD and SDA-FF combinations at coal-fired power plants, (2) evaluate the effect of SCR catalyst degradation on mercury capture; (3) evaluate the effect of low load operation on mercury capture in an SCR-FGD system, and (4) collect data that could provide the basis for fundamental scientific insights into the nature of mercury chemistry in flue gas, the catalytic effect of SCR systems on mercury speciation and the efficacy of different FGD technologies for mercury capture. This document, the ninth in a series of topical reports, describes the results and analysis of mercury sampling performed on Unit 1 at Plant 7, a 566 MW unit burning a bituminous coal containing 3.6% sulfur. The unit is equipped with a SCR, ESP, and wet FGD to control NO{sub x}, particulate, and SO{sub 2} emissions, respectively. Four sampling tests were performed in August 2004 during ozone season with the SCR operating; flue gas mercury speciation and concentrations were determined at the SCR inlet, SCR outlet, air heater outlet (ESP inlet), ESP outlet (FGD inlet), and at the stack (FGD outlet) using the Ontario Hydro method. Three sampling tests were also performed in November 2004 during non-ozone season with the SCR bypassed; flue gas mercury speciation and concentrations were determined at the ESP outlet (FGD inlet), and at the stack (FGD outlet). Process samples for material balances were collected during the flue gas measurements. The results show that, at the point where the flue gas enters the FGD, a greater percentage of the mercury was in the oxidized form when the SCR was operating compared to when the SCR was bypassed (97% vs 91%). This higher level of oxidation resulted in higher mercury removals in the FGD because the FGD removed 90-94% of the oxidized mercury in both cases. Total coal-to-stack mercury removal was 86% with the SCR operating, and 73% with the SCR bypassed. The average mercury mass balance closure was 81% during the ozone season tests and 87% during the non-ozone season tests.

J. A. Withum; S. C. Tseng; J. E. Locke

2006-01-31T23:59:59.000Z

262

EVALUATION OF MERCURY EMISSIONS FROM COAL-FIRED FACILITIES WITH SCR AND FGD SYSTEMS  

SciTech Connect

CONSOL Energy Inc., Research & Development (CONSOL), with support from the U.S. Department of Energy, National Energy Technology Laboratory (DOE) and the Electric Power Research Institute (EPRI), is evaluating the effects of selective catalytic reduction (SCR) on mercury (Hg) capture in coal-fired plants equipped with an electrostatic precipitator (ESP)--wet flue gas desulfurization (FGD) combination or a spray dryer absorber--fabric filter (SDA-FF) combination. In this program CONSOL is determining mercury speciation and removal at 10 coal-fired facilities. The objectives are (1) to evaluate the effect of SCR on mercury capture in the ESP-FGD and SDA-FF combinations at coal-fired power plants, (2) evaluate the effect of catalyst degradation on mercury capture; (3) evaluate the effect of low load operation on mercury capture in an SCR-FGD system, and (4) collect data that could provide the basis for fundamental scientific insights into the nature of mercury chemistry in flue gas, the catalytic effect of SCR systems on mercury speciation and the efficacy of different FGD technologies for mercury capture. This document, the seventh in a series of topical reports, describes the results and analysis of mercury sampling performed on a 1,300 MW unit burning a bituminous coal containing three percent sulfur. The unit was equipped with an ESP and a limestone-based wet FGD to control particulate and SO2 emissions, respectively. At the time of sampling an SCR was not installed on this unit. Four sampling tests were performed in September 2003. Flue gas mercury speciation and concentrations were determined at the ESP outlet (FGD inlet), and at the stack (FGD outlet) using the Ontario Hydro method. Process stream samples for a mercury balance were collected to coincide with the flue gas measurements. The results show that the FGD inlet flue gas oxidized:elemental mercury ratio was roughly 2:1, with 66% oxidized mercury and 34% elemental mercury. Mercury removal, on a coal-to-stack basis, was 53%. The average Hg concentration in the stack flue gas was 4.09 {micro}g/m{sup 3}. The average stack mercury emission was 3.47 Ib/TBtu. The mercury material balance closures ranged from 87% to 108%, with an average of 97%. A sampling program similar to this one was performed on a similar unit (at the same plant) that was equipped with an SCR for NOx control. Comparison of the results from the two units show that the SCR increases the percentage of mercury that is in the oxidized form, which, in turn, lends to more of the total mercury being removed in the wet scrubber. The principal purpose of this work is to develop a better understanding of the potential mercury removal ''co-benefits'' achieved by NOx, and SO{sub 2} control technologies. It is expected that this data will provide the basis for fundamental scientific insights into the nature of mercury chemistry in flue gas, the catalytic effect of SCR systems on mercury speciation and the efficacy of different FGD technologies for mercury capture. Ultimately, this insight could help to design and operate SCR and FGD systems to maximize mercury removal.

J.A. Withum; S.C. Tseng; J.E. Locke

2005-11-01T23:59:59.000Z

263

Evaluation of Mercury Emissions from Coal-Fired Facilities with SCR and FGD Systems  

Science Conference Proceedings (OSTI)

CONSOL Energy Inc., Research & Development (CONSOL), with support from the U.S. Department of Energy, National Energy Technology Laboratory (DOE) and the Electric Power Research Institute (EPRI), is evaluating the effects of selective catalytic reduction (SCR) on mercury (Hg) capture in coal-fired plants equipped with an electrostatic precipitator (ESP)--wet flue gas desulfurization (FGD) combination or a spray dyer absorber--fabric filter (SDA-FF) combination. In this program CONSOL is determining mercury speciation and removal at 10 coal-fired facilities. The principal purpose of this work is to develop a better understanding of the potential mercury removal ''co-benefits'' achieved by NO{sub x}, and SO{sub 2} control technologies. It is expected that this data will provide the basis for fundamental scientific insights into the nature of mercury chemistry in flue gas, the catalytic effect of SCR systems on mercury speciation and the efficacy of different FGD technologies for mercury capture. Ultimately, this insight could help to design and operate SCR and FGD systems to maximize mercury removal. The objectives are (1) to evaluate the effect of SCR on mercury capture in the ESP-FGD and SDA-FF combinations at coal-fired power plants, (2) evaluate the effect of SCR catalyst degradation on mercury capture; (3) evaluate the effect of low load operation on mercury capture in an SCR-FGD system, and (4) collect data that could provide the basis for fundamental scientific insights into the nature of mercury chemistry in flue gas, the catalytic effect of SCR systems on mercury speciation and the efficacy of different FGD technologies for mercury capture. This document, the tenth in a series of topical reports, describes the results and analysis of mercury sampling performed on two 468 MW units burning bituminous coal containing 1.3-1.7% sulfur. Unit 2 is equipped with an SCR, ESP, and wet FGD to control NO{sub x}, particulate, and SO{sub 2} emissions, respectively. Unit 1 is similar to Unit 2, except that Unit 1 has no SCR for NOx control. Four sampling tests were performed on both units in January 2005; flue gas mercury speciation and concentrations were determined at the economizer outlet, air heater outlet (ESP inlet), ESP outlet (FGD inlet), and at the stack (FGD outlet) using the Ontario Hydro method. Process samples for material balances were collected with the flue gas measurements. The results show that the SCR increased the oxidation of the mercury at the air heater outlet. At the exit of the air heater, a greater percentage of the mercury was in the oxidized and particulate forms on the unit equipped with an SCR compared to the unit without an SCR (97.4% vs 91%). This higher level of oxidation resulted in higher mercury removals in the scrubber. Total mercury removal averaged 97% on the unit with the SCR, and 87% on the unit without the SCR. The average mercury mass balance closure was 84% on Unit 1 and 103% on Unit 2.

J. A. Withum; J. E. Locke

2006-02-01T23:59:59.000Z

264

Optically powered firing system for the Procyon high explosive pulse power system  

DOE Green Energy (OSTI)

An optically powered fireset has been developed for the Procyon high explosive pulsed-power generator at Los Alamos National Laboratory. The fireset was located inside this flux compression experiment where large magnetic fields are generated. No energy sources were allowed inside the experiment and no wire connections can penetrate through the wall, of the experiment because of the high magnetic fields. The flux compression was achieved with high explosives in the experiment. The fireset was used to remotely charge a 1.2 {micro}f capacitor to 6,500V and to provide a readout of the voltage on the capacitor at the control room. The capacitor was charged by using two 7W fiber coupled GaAlAs laser diodes to illuminate two fiber coupled 12V solar cells. The solar cell outputs were connected in parallel to the input of a DC-DC converter which step up a 12V to 6,500V. A voltmeter, powered by illuminating a third 12V solar cell with 1W laser diode, was used to monitor the charge on the capacitor. The voltage was measured with a divider circuit, then converted to frequency in a V-F converter and transmitted to the control room over a fiber optic link. A fiducial circuit measured the capacitor firing current and provided an optical output timing pulse.

Earley, L.; Paul, J.; Rohlev, L.; Goforth, J.; Hall, C.R.

1995-10-01T23:59:59.000Z

265

Development of a coal-fired gas turbine cogeneration system: Status report  

SciTech Connect

The Allison Advanced Coal-Fueled Turbine Program is now in the sixth year of a development effort that has led to a POC engine demonstration test on a Coal-Water-Slurry (CWS) fuel. Earlier forecasts by CWS suppliers that suitable CWS fuels would be commercially available at an economic price have not been realized. A program replan has, therefore, been executed that incorporates the use of readily available dry pulverized coal. To support this program, technology issues relating to combustor performance and emission control, hot gas cleanup, and turbine deposition, erosion and corrosion (DEC) have been addressed. In addition, system assessment studies have been performed to evaluate the commercial prospects for small (<8 MWe) coal-fired industrial cogeneration systems and the application of the rich-quench-lean (RQL) coal-combustion technology to larger (> 100 MWe) utility-sized gas turbines. These results are reported by Wenglarz (1992). Combustor and engine tests on dry coal are now planned in preparation for a commercial demonstration that will follow the completion of this program.

Wilkes, C.; Wenglarz, R.A.; Hart, P.J.; Thomas, W.H.; Rothrock, J.W.; Harris, C.N.; Bourke, R.C.

1992-01-01T23:59:59.000Z

266

Multiplexed Optical Fiber Sensors for Coal Fired Advanced Fossil Energy Systems  

Science Conference Proceedings (OSTI)

This report summarizes technical progress on the program â??Multiplexed Optical Fiber Sensors for Coal Fired Advanced Fossil Energy Systemsâ?ť funded by the National Energy Technology Laboratory of the U.S. Department of Energy, and performed jointly by the Center for Photonics Technology of the Bradley Department of Electrical and Computer Engineering and the Department of Materials Science and Engineering at Virginia Tech. This three-year project started on October 1, 2008. In the project, a fiber optical sensing system based on intrinsic Fabry-Perot Interferometer (IFPI) was developed for strain and temperature measurements for Ultra Supercritical boiler condition assessment. Investigations were focused on sensor design, fabrication, attachment techniques and novel materials for high temperature and strain measurements. At the start of the project, the technical requirements for the sensing technology were determined together with our industrial partner Alstom Power. As is demonstrated in Chapter 4, all the technical requirements are successfully met. The success of the technology extended beyond laboratory test; its capability was further validated through the field test at DOE NETL, in which the sensors yielded distributed temperature mapping of a testing coupon installed in the turbine test rig. The measurement results agreed well with prior results generated with thermocouples. In this project, significant improvements were made to the IFPI sensor technology by splicing condition optimization, transmission loss reduction, sensor signal demodulation and sensor system design.

Anbo Wang; Gary Pickrell

2011-12-31T23:59:59.000Z

267

Flooding and Fire Ants (Spanish)  

E-Print Network (OSTI)

Fire ants can be a serious problem during and after a flood. This publication explains how to protect yourself when you must return to flooded structures or deal with storm debris.

Nester, Paul

2008-08-05T23:59:59.000Z

268

Engineering Technical Training Modules - Medium Voltage System Protection and Coordination Version 1.0  

Science Conference Proceedings (OSTI)

The purpose of this training module is to provide a basic understanding of protective relaying and coordination typically provided for medium voltage power systems. This module provides a discussion on current and potential transformers, the protective relays typically used as well as considerations for equipment protection and coordination or selective tripping. Medium voltage motor, transformer, and bus protection applications are covered. Lesson 4 focuses on emergency diesel generator protection in n...

2011-08-09T23:59:59.000Z

269

Degradation and Failure Characteristics of NPP Containment Protective Coating Systems  

SciTech Connect

Nuclear power plants (NPPs) must ensure that the emergency core cooling system (ECCS) or safety-related containment spray system (CSS) remains capable of performing its design safety function throughout the life of the plant. This requires ensuring that long-term core cooling can be maintained following a postulated loss-of-coolant accident (LOCA). Adequate safety operation can be impaired if the protective coatings which have been applied to the concrete and steel structures within the primary containment fail, producing transportable debris which could then accumulate on BWR ECCS suction strainers or PWR ECCS sump debris screens located within the containment. This document will present the data collected during the investigation of coating specimens from plants.

Sindelar, R.L.

2001-04-10T23:59:59.000Z

270

Study on Bipole Protection of #x00B1;800KV UHVDC System  

Science Conference Proceedings (OSTI)

The main circuit of UHVDC transmission system in China is introduced. Based on the ABB HVDC control protection system, the principle and method of the interface technology between the PSCAD/EMTDC and HIDRAW are introduced. An off-line real-time simulation ... Keywords: UHVDC protection, PSCAD/EMTDC, HIDRAW, Bipole protection

Xiao-kang Xu; Ming-chao Xia

2010-06-01T23:59:59.000Z

271

Sharing and Protection in a Single-Address-Space Operating System  

E-Print Network (OSTI)

of protection structures. Section 3 gives an overview of the basic Opal abstractions. Section 4 then describes or sparsely used data structures. Private-address-space systems force poor tradeoffs between protection, per others [Druschel et al. 1992 b]) that operat- ing system protection structures are not the right level

Levy, Hank

272

the proposed system provides with many characteris tic features such as multiple software protection with  

E-Print Network (OSTI)

can be used to protect many software packages in the same computer system. ffl The software provider the software. We represent the basic structure of the proposed soft­ ware protection system in Figure 1 protection with the same key, free distribution of UIP in advance, in­ stallation in multiple computer

Kim, Kwangjo

273

Forest fire management in Portugal : developing system insights through models of social and physical dynamics  

E-Print Network (OSTI)

Managing forest fires is a serious national problem in Portugal. Burned area has increased steadily over the past several decades, with particularly devastating years in 2003 and 2005. Ignitions also spike dramatically in ...

Collins, Ross D. (Ross Daniel)

2012-01-01T23:59:59.000Z

274

Proceedings of the coal-fired power systems 94: Advances in IGCC and PFBC review meeting. Volume 2  

Science Conference Proceedings (OSTI)

The Coal-Fired Power Systems 94 -- Advances in IGCC and PFBC Review Meeting was held June 21--23, 1994, at the Morgantown Energy Center (METC) in Morgantown, West Virginia. This Meeting was sponsored and hosted by METC, the Office of Fossil Energy, and the US Department of Energy (DOE). METC annually sponsors this conference for energy executives, engineers, scientists, and other interested parties to review the results of research and development projects; to discuss the status of advanced coal-fired power systems and future plans with the industrial contractors; and to discuss cooperative industrial-government research opportunities with METC`s in-house engineers and scientists. Presentations included industrial contractor and METC in-house technology developments related to the production of power via coal-fired Integrated Gasification Combined Cycle (IGCC) and Pressurized Fluidized Bed Combustion (PFBC) systems, the summary status of clean coal technologies, and developments and advancements in advanced technology subsystems, such as hot gas cleanup. A keynote speaker and other representatives from the electric power industry also gave their assessment of advanced power systems. This meeting contained 11 formal sessions and one poster session, and included 52 presentations and 24 poster presentations. Volume II contains papers presented at the following sessions: filter technology issues; hazardous air pollutants; sorbents and solid wastes; and membranes. Selected papers have been processed separately for inclusion in the Energy Science and Technology Database.

McDaniel, H.M.; Staubly, R.K.; Venkataraman, V.K. [eds.

1994-06-01T23:59:59.000Z

275

Coal-fired high performance power generating system. Draft quarterly progress report, January 1--March 31, 1995  

SciTech Connect

This report covers work carried out under Task 3, Preliminary R and D, under contract DE-AC22-92PC91155, ``Engineering Development of a Coal-Fired High Performance Power Generation System`` between DOE Pittsburgh Energy Technology Center and United Technologies Research Center. The goals of the program are to develop a coal-fired high performance power generation system (HIPPS) by the year 2000 that is capable of >47% thermal efficiency; NO{sub x}, SO{sub x} and particulates {le} 25% NSPS; cost {ge}65% of heat input; all solid wastes benign. A crucial aspect of the authors design is the integration of the gas turbine requirements with the HITAF output and steam cycle requirements. In order to take full advantage of modern highly efficient aeroderivative gas turbines they have carried out a large number of cycle calculations to optimize their commercial plant designs for both greenfield and repowering applications.

1995-10-01T23:59:59.000Z

276

Coal-fired high performance power generating system. Quarterly progress report, July 1, 1993--September 30, 1993  

Science Conference Proceedings (OSTI)

This report covers work carried out under Task 3, Preliminary Research and Development, and Task 4, Commercial Generating Plant Design, under contract DE-AC22-92PC91155, {open_quotes}Engineering Development of a Coal Fired High Performance Power Generation System{close_quotes} between DOE Pittsburgh Energy Technology Center and United Technologies Research Center. The goals of the program are to develop a coal-fired high performance power generation system (HIPPS) by the year 2000 that is capable of >47% thermal efficiency; NO{sub x}, SO{sub x}, and particulates {le} 25% NSPS; cost {ge} 65% of heat input; and all solid wastes benign. The report discusses progress in cycle analysis, chemical reactor modeling, ash deposition rate calculations for HITAF (high temperature advanced furnace) convective air heater, air heater materials, and deposit initiation and growth on ceramic substrates.

Not Available

1993-12-31T23:59:59.000Z

277

CRAD, Management - Office of River Protection K Basin Sludge Waste System |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Office of River Protection K Basin Sludge Waste Office of River Protection K Basin Sludge Waste System CRAD, Management - Office of River Protection K Basin Sludge Waste System May 2004 A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a May 2004 assessment of the Management at the Office of River Protection K Basin Sludge Waste System. CRADs provide a recommended approach and the types of information to gather to assess elements of a DOE contractor's programs. CRAD, Management - Office of River Protection K Basin Sludge Waste System More Documents & Publications CRAD, Emergency Management - Office of River Protection K Basin Sludge Waste System CRAD, Conduct of Operations - Office of River Protection K Basin Sludge

278

Coal-fired high performance power generating system. Quarterly progress report  

SciTech Connect

The goals of the program are to develop a coal-fired high performance power generation system (HIPPS) by the year 2000 that is capable of > 47% thermal efficiency; NO{sub x} SO {sub x} and Particulates < 25% NSPS; Cost of electricity 10% lower; coal > 65% of heat input and all solid wastes benign. In order to achieve these goals our team has outlined a research plan based on an optimized analysis of a 250 MW{sub e} combined cycle system applicable to both frame type and aeroderivative gas turbines. Under the constraints of the cycle analysis we have designed a high temperature advanced furnace (HITAF) which integrates several combustor and air heater designs with appropriate ash management procedures. Most of this report discusses the details of work on these components, and the R&D Plan for future work. The discussion of the combustor designs illustrates how detailed modeling can be an effective tool to estimate NO{sub x} production, minimum burnout lengths, combustion temperatures and even particulate impact on the combustor walls. When our model is applied to the long flame concept it indicates that fuel bound nitrogen will limit the range of coals that can use this approach. For high nitrogen coals a rapid mixing, rich-lean, deep staging combustor will be necessary. The air heater design has evolved into two segments: a convective heat exchanger downstream of the combustion process; a radiant panel heat exchanger, located in the combustor walls; The relative amount of heat transferred either radiatively or convectively will depend on the combustor type and the ash properties.

Not Available

1992-07-01T23:59:59.000Z

279

Coal-fired high performance power generating system. Quarterly progress report  

Science Conference Proceedings (OSTI)

The goals of the program are to develop a coal-fired high performance power generation system (HIPPS) by the year 2000 that is capable of > 47% thermal efficiency; NO{sub x} SO {sub x} and Particulates 65% of heat input and all solid wastes benign. In order to achieve these goals our team has outlined a research plan based on an optimized analysis of a 250 MW{sub e} combined cycle system applicable to both frame type and aeroderivative gas turbines. Under the constraints of the cycle analysis we have designed a high temperature advanced furnace (HITAF) which integrates several combustor and air heater designs with appropriate ash management procedures. Most of this report discusses the details of work on these components, and the R&D Plan for future work. The discussion of the combustor designs illustrates how detailed modeling can be an effective tool to estimate NO{sub x} production, minimum burnout lengths, combustion temperatures and even particulate impact on the combustor walls. When our model is applied to the long flame concept it indicates that fuel bound nitrogen will limit the range of coals that can use this approach. For high nitrogen coals a rapid mixing, rich-lean, deep staging combustor will be necessary. The air heater design has evolved into two segments: a convective heat exchanger downstream of the combustion process; a radiant panel heat exchanger, located in the combustor walls; The relative amount of heat transferred either radiatively or convectively will depend on the combustor type and the ash properties.

Not Available

1992-07-01T23:59:59.000Z

280

Design of an expert system to aid in the selection of a wood fired boiler system.  

E-Print Network (OSTI)

??Currently most industrial and institutional facilities rely on fossil fuels to power their boiler systems. As the quantity of these non-renewable resources is depleted, and… (more)

Morris, Melissa L.

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Engineering development of coal-fired high-performance power systems. Progress report, April 1--June 30, 1996  

SciTech Connect

In Phase 1 of the project, a conceptual design of a coal-fired, high-performance power system (HIPPS) was developed, and small-scale R and D was done in critical areas of the design. The current phase of the project includes development through the pilot plant stage and design of a prototype plant that would be built in Phase 3. The power-generating system being developed in this project will be an improvement over current coal-fired systems. It is a combined-cycle plant. This arrangement is referred to as the All Coal HIPPS because it does not require any other fuels for normal operation. A fluidized bed, air-blown pyrolyzer converts coal into fuel gas and char. The char is fired in a high-temperature advanced furnace (HITAF) which heats both air for a gas turbine and steam for a steam turbine. The fuel gas from the pyrolyzer goes to a topping combustor where it is used to raise the air entering the gas turbine to 1288 C. In addition to the HITAF, steam duty is achieved with a heat-recovery steam generator (HRSG) in the gas turbine exhaust stream and economizers in the HITAF flue gas exhaust stream. Progress during the quarter is described.

1996-12-31T23:59:59.000Z

282

Upgrade of the DIII-D vacuum vessel protection system  

SciTech Connect

An upgrade of the General Atomics DIII-D tokamak armor protection system has been completed. The upgrade consisted of armoring the outer wall and the divertor gas baffle with monolithic graphite tiles and cleaning the existing floor, ceiling, and inner wall tiles to remove any deposited impurity layer from the tile surfaces. The new tiles replace the graphite tiles used as local armor for neutral beam shine through, three graphite poloidal back-up limiter bands, and miscellaneous Inconel protection tiles. The total number of tiles increased from 1636 to 3200 and corresponding vessel coverage from 40% to 90%. A new, graphite armored, toroidally continuous, gas baffle between the outer wall and the biased divertor ring was installed in order to accommodate the cryocondensation pump that was installed in parallel with the outer wall tiles. To eliminate a source of copper in the plasma, GRAFOIL gaskets replaced the copper felt metal gaskets previously used as a compliant heat transfer interface between the inertially cooled tiles and the vessel wall. GRAFOIL, an exfoliated, flexible graphite material from Union Carbide, Inc., was used between each tile and the vessel wall and also between each tile and its hold-down hardware. Testing was performed to determine the mechanical compliance, thermal conductance, and vacuum characteristics of the GRAFOIL material. To further decrease the quantity of high Z materials exposed to the plasma, the 1636 existing graphite tiles were identified, removed, and grit blasted to eliminate a thin layer of deposited metals which included nickel, chromium, and molybdenum. Prior to any processing, a selected set of tiles was tested for radioactivity, including tritium contamination. The tiles were grit blasted in a negative-pressure blasting cabinet using 37 {mu}m boron carbide powder as the blast media and dry nitrogen as the propellant.

Hollerbach, M.A.; Lee, R.L.; Smith, J.P.; Taylor, P.L.

1993-10-01T23:59:59.000Z

283

Development of a high-performance coal-fired power generating system with pyrolysis gas and char-fired high temperature furnace (HITAF). Quarterly progress report No. 3, July--September 1992  

SciTech Connect

A concept for an advanced coal-fired combined-cycle power generating system is currently being developed. The first phase of this three-phase program consists of conducting the necessary research and development to define the system, evaluate the economic and technical feasibility of the concept, and prepare an R & D plan to develop the concept further. Foster Wheeler Development Corporation is leading a team ofcompanies involved in this effort. The system proposed to meet these goals is a combined-cycle system where air for a gas turbine is indirectly heated to approximately 1800{degrees}F in furnaces fired with cool-derived fuels and then directly heated in a natural-gas-fired combustor up to about 2400{degrees}F. The system is based on a pyrolyzing process that converts the coal into a low-Btu fuel gas and char. The fuelgas is a relatively clean fuel, and it is fired to heat tube surfaces that are susceptible to corrosion and problems from ash deposition. In particular, the high-temperature air heater tubes, which will need tobe a ceramic material, will be located in a separate furnace or region of a furnace that is exposed to combustion products from the low-Btu fuel gas only. A simplified process flow diagram is shown.

Not Available

1992-11-01T23:59:59.000Z

284

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... to Evaluate Fire Models for Nuclear Power Plant Applications: Summary ... pool fires; nuclear power plants; fire models; computational fluid dynamics ...

285

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... fire models; nuclear power plants; fire hazard analysis; fire risk assessment ... to Evaluate Fire Models for Nuclear Power Plant Applications' (ICFMP). ...

286

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... the Fire Resistance of Barriers for Nuclear Power Plant Applications. ... nuclear power plants; ASTM E119; cables; fire barriers; fire endurance; fire ...

287

EVALUATION OF MERCURY EMISSIONS FROM COAL-FIRED FACILITIES WITH SCR AND FGD SYSTEMS  

Science Conference Proceedings (OSTI)

CONSOL Energy Inc., Research & Development (CONSOL), with support from the U.S. Department of Energy, National Energy Technology Laboratory (DOE) and the Electric Power Research Institute (EPRI), evaluated the effects of selective catalytic reduction (SCR) on mercury (Hg) capture in coal-fired plants equipped with an electrostatic precipitator (ESP)-wet flue gas desulfurization (FGD) combination or a spray dyer absorber-fabric filter (SDA-FF) combination. In this program CONSOL determined mercury speciation and removal at 10 bituminous coal-fired facilities; at four of these facilities, additional tests were performed on units without SCR, or with the existing SCR bypassed. This project final report summarizes the results and discusses the findings of the body of work as a whole. Eleven Topical Reports were issued (prior to this report) that describe in great detail the sampling results at each of the ten power plants individually. The results showed that the SCR-FGD combination removed a substantial fraction of mercury from flue gas. The coal-to-stack mercury removals ranged from 65% to 97% for the units with SCR and from 53% to 87% for the units without SCR. There was no indication that any type of FGD system was more effective at mercury removal than others. The coal-to-stack mercury removal and the removal in the wet scrubber were both negatively correlated with the elemental mercury content of the flue gas and positively correlated with the scrubber liquid chloride concentration. The coal chlorine content was not a statistically significant factor in either case. Mercury removal in the ESP was positively correlated with the fly ash carbon content and negatively correlated with the flue gas temperature. At most of the units, a substantial fraction (>35%) of the flue gas mercury was in the elemental form at the boiler economizer outlet. After passing through the SCR-air heater combination very little of the total mercury (<10%) remained in the elemental form in the flue gas; this was true for all SCR catalyst types and sources. Although chlorine has been suggested as a factor affecting the mercury speciation in flue gas, coal chlorine was not a statistically significant factor affecting mercury speciation at the economizer exit or at the air heater exit. The only statistically significant factors were the coal ash CaO content and the fly ash carbon content; the fraction of mercury in the elemental form at the economizer exit was positively correlated with both factors. In a direct comparison at four SCR-equipped units vs. similar units at the same sites without SCR (or with the SCR bypassed), the elemental mercury fractions (measured at the ESP outlet) were lower, and the coal-to-stack mercury removals were higher, when the SCR was present and operating. The average coal-to-stack mercury removal at the four units without an operating SCR was 72%, whereas the average removal at the same sites with operating SCRs was 88%. The unit mercury mass balance (a gauge of the overall quality of the tests) at all of the units ranged from 81% to 113%, which were within our QA/QC criterion of 80-120%.

J.A. Withum

2006-03-07T23:59:59.000Z

288

Enhancing reliability in passive anti-islanding protection schemes for distribution systems with distributed generation.  

E-Print Network (OSTI)

??This thesis introduces a new approach to enhance the reliability of conventional passive anti-islanding protection scheme in distribution systems embedding distributed generation. This approach uses… (more)

Sheikholeslamzadeh, Mohsen

2012-01-01T23:59:59.000Z

289

Fully automated smart wireless frost prediction and protection system using a fuzzy logic controller  

Science Conference Proceedings (OSTI)

A smart fuzzy logic controller system is presented to protect the crops from frost damage that occurs every year. The system is a fully automated system to predict the frost and to protect the crops using wireless sensor network technology. The sensors ...

Shadi A. Alboon; Amin T. Alqudah; Hussein R. Al-Zoubi; Abedalgany A. Athamneh

2012-09-01T23:59:59.000Z

290

FIERAsystem: A Fire Risk Assessment Model for Light Industrial Building Fire Safety Evaluation  

E-Print Network (OSTI)

this report. The current report describes the framework for the new model, individual submodels used for calculations, and the information that the model provides to the design engineer or building official. The framework that FIERAsystem uses to conduct a hazard analysis and the process used to perform a risk analysis are also discussed in the report. 2. FRAMEWORK OF FIERAsystemMODEL The FIERAsystem model allows the user to perform a number of fire protection engineering calculations in order to evaluate fire protection systems in industrial buildings. At start-up, FIERAsystem provides several calculation options, which allow the user to: use standard engineering correlations, run individual submodels, conduct a hazard analysis, or conduct a risk analysis

N. Kashef; A. Torvi; G. Reid; Noureddine Benichou; Ahmed Kashef; David Torvi; George Hadjisophocleous; Irene Reid

2002-01-01T23:59:59.000Z

291

Calculation of Fire Severity Factors and Fire Non-Suppression Probabilities For A DOE Facility Fire PRA  

Science Conference Proceedings (OSTI)

Over a 12 month period, a fire PRA was developed for a DOE facility using the NUREG/CR-6850 EPRI/NRC fire PRA methodology. The fire PRA modeling included calculation of fire severity factors (SFs) and fire non-suppression probabilities (PNS) for each safe shutdown (SSD) component considered in the fire PRA model. The SFs were developed by performing detailed fire modeling through a combination of CFAST fire zone model calculations and Latin Hypercube Sampling (LHS). Component damage times and automatic fire suppression system actuation times calculated in the CFAST LHS analyses were then input to a time-dependent model of fire non-suppression probability. The fire non-suppression probability model is based on the modeling approach outlined in NUREG/CR-6850 and is supplemented with plant specific data. This paper presents the methodology used in the DOE facility fire PRA for modeling fire-induced SSD component failures and includes discussions of modeling techniques for: • Development of time-dependent fire heat release rate profiles (required as input to CFAST), • Calculation of fire severity factors based on CFAST detailed fire modeling, and • Calculation of fire non-suppression probabilities.

Tom Elicson; Bentley Harwood; Jim Bouchard; Heather Lucek

2011-03-01T23:59:59.000Z

292

Control strategies of doubly fed induction generator-based wind turbine system with new rotor current protection topology  

Science Conference Proceedings (OSTI)

A protection scheme of a doubly fed induction generator (DFIG) based wind turbine system during faults is crowbar activation. With this protection

Jackson John Justo; Kyoung-Soo Ro

2012-01-01T23:59:59.000Z

293

Emergency, Fire Information  

NLE Websites -- All DOE Office Websites (Extended Search)

Emergency, Fire Information Emergency, Fire Information Emergency, Fire Information Protecting our people, emergency personnel, national security information, facilities, lands, and neighboring communities. Contact Communications Office (505) 667-7000 Email LANL Update (505) 667-6622 or (877) 723-4101 toll-free Emergency Public Information In the event of an emergency, Los Alamos National Laboratory will provide you with needed information here as it becomes available. The Los Alamos Site Office/Los Alamos National Laboratory Emergency Public Information Plan provides a framework for coordinated, accurate, and timely release of information to Laboratory employees, the news media, potentially affected members of the public, and other stakeholders. Want emergency news emailed to you? Subscribe here.

294

CRAD, Training - Office of River Protection K Basin Sludge Waste System |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Office of River Protection K Basin Sludge Waste Office of River Protection K Basin Sludge Waste System CRAD, Training - Office of River Protection K Basin Sludge Waste System May 2004 A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a May 2004 assessment of the Environment, Safety and Health program at the Office of River Protection K Basin Sludge Waste System. CRADs provide a recommended approach and the types of information to gather to assess elements of a DOE contractor's programs. CRAD, Training - Office of River Protection K Basin Sludge Waste System More Documents & Publications CRAD, Emergency Management - Office of River Protection K Basin Sludge

295

CRAD, Engineering - Office of River Protection K Basin Sludge Waste System  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Engineering - Office of River Protection K Basin Sludge Waste Engineering - Office of River Protection K Basin Sludge Waste System CRAD, Engineering - Office of River Protection K Basin Sludge Waste System May 2004 A section of Appendix C to DOE G 226.1-2 "Federal Line Management Oversight of Department of Energy Nuclear Facilities." Consists of Criteria Review and Approach Documents (CRADs) used for a May 2004 assessment of the Engineering program at the Office of River Protection K Basin Sludge Waste System. CRADs provide a recommended approach and the types of information to gather to assess elements of a DOE contractor's programs. CRAD, Engineering - Office of River Protection K Basin Sludge Waste System More Documents & Publications CRAD, Emergency Management - Office of River Protection K Basin Sludge

296

Alternative approach for fire supression of class A, B and C fires in gloveboxes  

SciTech Connect

Department of Energy (DOE) Orders and National Fire Protection Association (NFPA) Codes and Standards require fire suppression in gloveboxes. Several potential solutions have been and are currently being considered at Los Alamos National Laboratory (LANL). The objective is to provide reliable, minimally invasive, and seismically robust fire suppression capable of extinguishing Class A, B, and C fires; achieve compliance with DOE and NFPA requirements; and provide value-added improvements to fire safety in gloveboxes. This report provides a brief summary of current approaches and also documents the successful fire tests conducted to prove that one approach, specifically Fire Foe{trademark} tubes, is capable of achieving the requirement to provide reliable fire protection in gloveboxes in a cost-effective manner.

Rosenberger, Mark S [Los Alamos National Laboratory; Tsiagkouris, James A [Los Alamos National Laboratory

2011-01-01T23:59:59.000Z

297

Configuration and Setting Management for Protection and Control Devices and Systems  

Science Conference Proceedings (OSTI)

The EPRI roadmap reports forecast that as protection equipment and systems continuously evolve in the more feature-rich and sophisticated direction, management of the configuration and setting is becoming more critical in future. In 2011 EPRI Protection and Control (P&C) survey, configuration and setting management for protection and control systems remain one of the most pressing challenges for member utilities.To handle the growing complexity of today’s P&C asset ...

2012-12-14T23:59:59.000Z

298

Configuration and Setting Management for Protection and Control Devices and Systems  

Science Conference Proceedings (OSTI)

The EPRI roadmap reports [6] [7] forecast that as protection equipment and systems continuously evolve in the more feature-rich and sophisticated direction, management of the configuration and setting is becoming more critical in future. In 2011 EPRI Protection and Control (P&C) survey, it was confirmed that configuration and setting management for protection and control devices and systems was one of the most pressing challenges from members.To handle the ...

2013-12-20T23:59:59.000Z

299

NNSA joins other federal agencies to build Interagency Fire Center...  

NLE Websites -- All DOE Office Websites (Extended Search)

to enhance northern New Mexico fire protection efforts by building a 6,400 square foot facility to serve as a joint coordination and response center for fire events. The new...

300

Computational Fluid Dynamics (CFD) Modelling on Soot Yield for Fire  

E-Print Network (OSTI)

) , CIBSE Guide E(iii) , etc. All design parameters of the smoke control strategy and architectural design Fire Protection Association, Quincy, MA, USA, 2007. iii CIBSE Guide E, Fire Engineering, 2nd Edition

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Conceptual design of a coal-fired MHD retrofit plant. Topical report, Seed Regeneration System Study 2  

SciTech Connect

Westinghouse Advanced Energy Systems (WAES), through Contract No. DE-AC22-87PC79668 funded by US DOE/PETC, is conducting a conceptual design study to evaluate a coal-fired magnetohydrodynamic (MHD) retrofit of a utility plant of sufficient size to demonstrate the technical and future economic viability of an MHD system operating within an electric utility environment. The objective of this topical report is to document continuing seed regeneration system application studies and the definition of will system integration requirements for the Scholz MHD retrofit plant design. MHD power plants require the addition of a seeding material in the form of potassium to enhance the ionization of the high temperature combustion gas in the MHD channel. This process has an added environmental advantage compared to other types of coal-fired power plants in that the potassium combines with the naturally occurring sulfur in the coal to form a potassium sulfate flyash (K{sub 2}SO{sub 4}) which can be removed from the process by appropriate particulate control equipment. Up to 100% of the Sulfur in the coal can be removed by this process thereby providing environmentally clean power plant operation that is better than required by present and anticipated future New Source Performance Standards (NSPS).

1992-11-01T23:59:59.000Z

302

Protection and Control for Grid Connected Photovoltaic Power Generation System Based on Instantaneous Power Theory  

Science Conference Proceedings (OSTI)

Reliable protection and reasonable control run an important role in grid connected PV power generation system. The detection and calculation of real and reactive power are the bases of many inverter resident passive and active islanding detection method ... Keywords: Distributed generation, photovoltaic system, grid connected, protection and control, power theory

Fei Wang; Chengcheng Zhang

2009-05-01T23:59:59.000Z

303

Implementation of a testing and diagnostic concept for an NPP reactor protection system  

Science Conference Proceedings (OSTI)

This paper presents the concept and practical realization of the testing and diagnostic methodology for a reactor protection system in a nuclear power plant. The test concept utilizes the highly redundant nature of these systems to conduct tests during ...

Tamás Bartha; István Varga; Alexandros Soumelidis; Géza Szabé

2005-04-01T23:59:59.000Z

304

Development of a high-performance coal-fired power generating system with pyrolysis gas and char-fired high temperature furnace (HITAF). Progress report No. 12, September--December 1994  

SciTech Connect

A concept for an advanced coal-fired combined-cycle power generating system is currently being developed. The first phase of this three-phase program consists of conducting the necessary research and development to define the system, evaluating the economic and technical feasibility of the concept, and preparing an R&D plan to develop the concept further. There are two basic arrangements of our HIPPS cycle. Both are coal-fired combined cycles. One arrangement is the 35% natural gas HIPPS. Coal is converted to fuel gas and char in a pyrolysis process, and these fuels are fired in separate parts of a high temperature advanced furnace (HITAF). The char-fired furnace produces flue gas that is used to heat gas turbine air up to 1400 F. Alloy tubes are used for these tube banks. After leaving the alloy tube banks, the gas turbine air goes through a ceramic air heater where it is heated from 1400 F to 1800 F. The flue gas that goes through the ceramic air heater comes from the combustion of the fuel gas that is produced in the pyrolysis process. This fuel gas is cleaned to remove particulates and alkalies that would corrode and plug a ceramic air heater. The air leaving the ceramic air heater needs to be heated further to achieve the efficiency goal of 47%, and this is done by firing natural gas in the gas turbine combustor. An alternative arrangement of the HIPPS cycle is called the All Coal HIPPS. With this arrangement, the char is used to heat the gas turbine air to 1400 F as before, but instead of then going to a ceramic air heater, the air goes directly to the gas turbine combustor. The fuel gas generated in the pyrolyzer is used as fuel in the gas turbine combustor. In both cycle arrangements, heat is transferred to the steam cycle in the HITAF and a heat recovery steam generator (HRSG).

1995-06-01T23:59:59.000Z

305

DOE/Contractor Fire Safety Workshop Proceedings, May 14 - May...  

NLE Websites -- All DOE Office Websites (Extended Search)

and Integrated Testing of Fire and Life Safety Systems: Charles Kilfoil NFPA 652 Fundamentals of Combustible Dusts: Robert F. Bitter Overview: Enterprise-Level Industrial Fire...

306

Study of the Heating Load of a Manufactured Space with a Gas-fired Radiant Heating System  

E-Print Network (OSTI)

A thermal balance mathematics model of a manufactured space with a gas-fired radiant heating system is established to calculate the heating load. Computer programs are used to solve the model. Envelope internal surface temperatures under different outdoor temperatures are obtained, and the heating load of the manufactured space is analyzed. The relationship between the envelope internal surface temperature and the workspace temperature is also analyzed in this paper. CFD simulation software is used to simulate the temperature field and the envelope's internal surface temperature of the manufacture space with hot-air heating system. Comparison and analysis of heating loads are done between the manufactured spaces with convection heating and radiant heating systems.

Zheng, X.; Dong, Z.

2006-01-01T23:59:59.000Z

307

Fuel supply system and method for coal-fired prime mover  

DOE Patents (OSTI)

A coal-fired gas turbine engine is provided with an on-site coal preparation and engine feeding arrangement. With this arrangement, relatively large dry particles of coal from an on-site coal supply are micro-pulverized and the resulting dry, micron-sized, coal particulates are conveyed by steam or air into the combustion chamber of the engine. Thermal energy introduced into the coal particulates during the micro-pulverizing step is substantially recovered since the so-heated coal particulates are fed directly from the micro-pulverizer into the combustion chamber.

Smith, William C. (Morgantown, WV); Paulson, Leland E. (Morgantown, WV)

1995-01-01T23:59:59.000Z

308

The application of expansion foam on liquefied natural gas (LNG) to suppress LNG vapor and LNG pool fire thermal radiation  

E-Print Network (OSTI)

Liquefied Natural Gas (LNG) hazards include LNG flammable vapor dispersion and LNG pool fire thermal radiation. A large LNG pool fire emits high thermal radiation thus preventing fire fighters from approaching and extinguishing the fire. One of the strategies used in the LNG industry and recommended by federal regulation National Fire Protection Association (NFPA) 59A is to use expansion foam to suppress LNG vapors and to control LNG fire by reducing the fire size. In its application, expansion foam effectiveness heavily depends on application rate, generator location, and LNG containment pit design. Complicated phenomena involved and previous studies have not completely filled the gaps increases the needs for LNG field experiments involving expansion foam. In addition, alternative LNG vapor dispersion and pool fire suppression methodology, Foamglas® pool fire suppression (PFS), is investigated as well. This dissertation details the research and experiment development. Results regarding important phenomena are presented and discussed. Foamglas® PFS effectiveness is described. Recommendations for advancing current guidelines in LNG vapor dispersion and pool fire suppression methods are developed. The gaps are presented as the future work and recommendation on how to do the experiment better in the future. This will benefit LNG industries to enhance its safety system and to make LNG facilities safer.

Suardin, Jaffee Arizon

2008-08-01T23:59:59.000Z

309

Real-time fire detection in low quality video  

E-Print Network (OSTI)

Motivation for a Robust Video-based Fire Detection SystemFigure 3.1: Screen shots of training videos with fire inshots of training videos with no fire in them. . . . . . .

True, Nicholas James

2010-01-01T23:59:59.000Z

310

Methods for Applying Risk Analysis to Fire Scenarios (MARIAFIRES)  

Science Conference Proceedings (OSTI)

The U.S. Nuclear Regulatory Commission (NRC) approved the risk-informed and performance-based alternative regulation 10 CFR 50.48(c) in July 2004, which allows licensees the option of using fire protection requirements contained in the National Fire Protection Association (NFPA) Standard 805, "Performance Based Standard for Fire Protection for Light-Water Reactor Electric Generating Plants, 2001 Edition," with certain exceptions. To support licensees' use of that option, NRC and the Electric Power Resear...

2010-12-17T23:59:59.000Z

311

Fires - 1946  

NLE Websites -- All DOE Office Websites (Extended Search)

Fires - 1946 Fires - 1946 Nature Bulletin No. 85 September 28, 1946 Forest Preserve District of Cook County Clayton F. Smith, President Roberts Mann, Superintendent of Conservation FIRES - 1946 It happens every fall. Thousands of acres of vacant land are being burned-off: some of them because of matches, cigarettes or pipe dottle carelessly tossed aside along the highways and along the trails; some of them set afire by thoughtless boys; most of them deliberately burned by people who believe they will improve the crop of grass next year. That is stupid. And if you start a fire which burns over another person's property you are liable to arrest and heavy penalty, under the Illinois law, unless you have given that person proper notice of your intention. Fires harm -- they never help. The tough seeds and roots of the worthless grasses and weeds survive a fire but the good nutritious grasses and most wildflowers are killed. Further, all the winter food and cover for birds and other wildlife are destroyed.

312

Plant Modernization with Digital Reactor Protection System Safety System Upgrades at US Nuclear Power Stations  

SciTech Connect

As the current fleet of nuclear power plants in the US reaches 25+ years of operation, obsolescence is driving many utilities to implement upgrades to both their safety and non-safety-related Instrumentation and Control (I and C) Systems. Digital technology is the predominant replacement technology for these upgrades. Within the last 15 years, digital control systems have been deployed in non-safety- related control applications at many utilities. In addition, a few utilities have replaced small safety-related systems utilizing digital technology. These systems have shown digital technology to be robust, reliable and simpler to maintain. Based upon this success, acceptance of digital technology has gained momentum with both utilities and regulatory agencies. Today, in an effort to extend the operating lives of their nuclear stations and resolve obsolescence of critical components, utilities are now pursuing digital technology for replacement of their primary safety systems. AREVA is leading this effort in the United States with the first significant digital upgrade of a major safety system. AREVA has previously completed upgrades to safety-related control systems emergency diesel engine controls and governor control systems for a hydro station which serves as the emergency power source for a nuclear station. Currently, AREVA is implementing the replacement of both the Reactor Protection System (RPS) and the Engineered Safety Features Actuation System (ESFAS) on all three units at a US PWR site. (authors)

Heckle, Wm. Lloyd; Bolian, Tricia W. [AREVA NP, an AREVA and Siemens Company, 1345 Ridgeland Parkway, Suite 130 (United States)

2006-07-01T23:59:59.000Z

313

Oil-Well Fire Fighting  

Science Conference Proceedings (OSTI)

... Oil Well Fire Fighting. NIST fire Research NIST Fire Research 2 Oil Well Fire Fighting RoboCrane Model Oil Well Fire Fighting Working Model.

2011-08-25T23:59:59.000Z

314

Gas-fired desiccant dehumidification system field evaluation in a quick-service restaurant. Final report, October 1989  

Science Conference Proceedings (OSTI)

This report describes the results of a field evaluation of state-of-art desiccant dehumidification equipment in Houston, TX. The evaluation demonstrated that comfort control in a quick-service restaurant could be improved dramatically. However, available gas-fired desiccant dehumidification equipment is too expensive, inefficient, and unreliable to be considered for wide application in the restaurant industry. Results of a technical and economic analysis of four HVAC options in four U.S. cities indicated that improved comfort control could be achieved with only a modest increase in operating costs with an advanced system. This, coupled with the economic benefits achieved through lower indoor humidity such as improved crew performance and reduced maintenance costs, could justify the introduction of an advanced, integrated, HVAC system using desiccant technology which has an installed cost similar to current equipment.

Koopman, R.N.; Marciniak, T.J.

1989-10-01T23:59:59.000Z

315

Direct fired heat exchanger  

DOE Patents (OSTI)

A gas-to-liquid heat exchanger system which transfers heat from a gas, generally the combustion gas of a direct-fired generator of an absorption machine, to a liquid, generally an absorbent solution. The heat exchanger system is in a counterflow fluid arrangement which creates a more efficient heat transfer.

Reimann, Robert C. (Lafayette, NY); Root, Richard A. (Spokane, WA)

1986-01-01T23:59:59.000Z

316

Limitations imposed on fire PRA methods as the result of incomplete and uncertain fire event data.  

SciTech Connect

Fire probabilistic risk assessment (PRA) methods utilize data and insights gained from actual fire events in a variety of ways. For example, fire occurrence frequencies, manual fire fighting effectiveness and timing, and the distribution of fire events by fire source and plant location are all based directly on the historical experience base. Other factors are either derived indirectly or supported qualitatively based on insights from the event data. These factors include the general nature and intensity of plant fires, insights into operator performance, and insights into fire growth and damage behaviors. This paper will discuss the potential methodology improvements that could be realized if more complete fire event reporting information were available. Areas that could benefit from more complete event reporting that will be discussed in the paper include fire event frequency analysis, analysis of fire detection and suppression system performance including incipient detection systems, analysis of manual fire fighting performance, treatment of fire growth from incipient stages to fully-involved fires, operator response to fire events, the impact of smoke on plant operations and equipment, and the impact of fire-induced cable failures on plant electrical circuits.

Nowlen, Steven Patrick; Hyslop, J. S. (U.S. Nuclear Regulatory Commission, Washington, DC)

2010-04-01T23:59:59.000Z

317

Analysis of vehicle fuel release resulting in waste tank fire  

Science Conference Proceedings (OSTI)

This document reevaluates several aspects of the in-tank vehicle fuel fire/deflagration accident formally documented as an independent accident (representative accident [rep acc] 2). This reevaluation includes frequencies for the accidents and incorporates the behavior of gasoline and diesel fuel in more detail than previous analysis. This reevaluation uses data from RPP-13121, ''Historical Summary of Occurrences from the Tank Farm Safety Analysis Report'', Table B-1, ''Tank Farm Events, Off-Normal and Critiques,'' and B-2, ''Summary of Occurrences,'' and from the River Protection Project--Occurrence Reporting & Processing System (ORPS) reports as a basis for changing some of the conclusions formally reported in HNF-SD-WM-CN-037, ''Frequency Analysis of Vehicle Fuel Releases Resulting in Waste Tank Fire''. This calculation note will demonstrate that the in-tank vehicle fuel fire/deflagration accident event may be relocated to other, more bounding accidents.

STEPHENS, L.S.

2003-03-21T23:59:59.000Z

318

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Evaluation of Fire Models for Nuclear Power Plant Applications: Cable Tray Fires ... cable trays; fire models; nuclear power plants; containment; ignition ...

319

A Physical Protection Systems Test Bed for International Counter-Trafficking System Development  

Science Conference Proceedings (OSTI)

Physical protection systems have a widespread impact on the nuclear industry in areas such as nuclear safeguards, arms control, and trafficking of illicit goods (e.g., nuclear materials) across international borders around the world. Many challenges must be overcome in design and deployment of foreign border security systems such as lack of infrastructure, extreme environmental conditions, limited knowledge of terrain, insider threats, and occasional cultural resistance. Successful security systems, whether it be a system designed to secure a single facility or a whole border security system, rely on the entire integrated system composed of multiple subsystems. This test bed is composed of many unique sensors and subsystems, including wireless unattended ground sensors, a buried fiber-optic acoustic sensor, a lossy coaxial distributed sensor, wireless links, pan-tilt-zoom cameras, mobile power generation systems, unmanned aerial vehicles, and fiber-optic-fence intrusion detection systems. A Common Operating Picture software architecture is utilized to integrate a number of these subsystems. We are currently performance testing each system for border security and perimeter security applications by examining metrics such as probability of sense and a qualitative understanding of the sensor s vulnerability of defeat. The testing process includes different soil conditions for buried sensors (e.g., dry, wet, and frozen) and an array of different tests including walking, running, stealth detection, and vehicle detection. Also, long term sustainability of systems is tested including performance differences due to seasonal variations (e.g. summer versus winter, while raining, in foggy conditions). The capabilities of the test bed are discussed. Performance testing results, both at the individual component level and integrated into a larger system for a specific deployment (in situ), help illustrate the usefulness and need for integrated testing facilities to carry out this mission. The test bed provides access to grassy fields, wooded areas, and a large waterway three distinct testing environments. The infrastructure supporting deployment of systems at the test bed includes grid power, renewable power systems, climate controlled enclosures, high bandwidth wireless links, and a fiber optic communications backbone. With over 10 acres of dedicated area and direct waterway access, the test bed is well suited for long term test and evaluation of physical protection and security systems targeting a wide range of applications.

Stinson, Brad J [ORNL; Kuhn, Michael J [ORNL; Donaldson, Terrence L [ORNL; Richardson, Dave [ORNL; Rowe, Nathan C [ORNL; Younkin, James R [ORNL; Pickett, Chris A [ORNL

2011-01-01T23:59:59.000Z

320

DEVELOPMENT OF FINE PARTICULATE EMISSION FACTORS AND SPECIATION PROFILES FOR OIL AND GAS FIRED COMBUSTION SYSTEMS  

SciTech Connect

This report provides results from the second year of this three-year project to develop dilution measurement technology for characterizing PM2.5 (particles with aerodynamic diameter smaller than 2.5 micrometers) and precursor emissions from stationary combustion sources used in oil, gas and power generation operation. Detailed emission rate and chemical speciation tests results for a gas turbine, a process heater, and a commercial oil/gas fired boiler are presented. Tests were performed using a research dilution sampling apparatus and traditional EPA methods. A series of pilot tests were conducted to identify the constraints to reduce the size of current research dilution sampler for future stack emission tests. Based on the test results, a bench prototype compact dilution sampler developed and characterized in GE EER in August 2002.

Glenn England; Oliver Chang; Stephanie Wien

2002-02-14T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Engineering development of advanced coal-fired low-emission boiler system. Technical progress report No. 1, August--December 1992  

Science Conference Proceedings (OSTI)

The Pittsburgh Energy Technology Center of the US Department of Energy (DOE) has contracted with Combustion Engineering, Inc. (ABB CE) to perform work on the ``Engineering Development of Advanced Coal-Fired Low-Emission Boiler Systems`` Project and has authorized ABB CE to complete Phase I on a cost-reimbursable basis. The overall objective of the Project is the expedited commercialization of advanced coal-fired low-emission boiler systems. The specified primary objectives are: NO{sub x} emissions not greater than one-third NSPS; SO{sub x} emissions not greater than one-third NSPS; and particulate emissions not greater than one-half NSPS. The specific secondary objectives are: Improved ash disposability and reduced waste generation; reduced air toxics emissions; increased generating efficiency. The final deliverables are a design data base that will allow future coal-fired power plants to meet the stated objectives and a preliminary design of a commercial generation unit.

Not Available

1993-02-26T23:59:59.000Z

322

Fire Hazard Analysis for the Cold Vacuum Drying facility (CVD) Facility  

DOE Green Energy (OSTI)

The CVDF is a nonreactor nuclear facility that will process the Spent Nuclear Fuels (SNF) presently stored in the 105-KE and 105-KW SNF storage basins. Multi-canister overpacks (MCOs) will be loaded (filled) with K Basin fuel transported to the CVDF. The MCOs will be processed at the CVDF to remove free water from the fuel cells (packages). Following processing at the CVDF, the MCOs will be transported to the CSB for interim storage until a long-term storage solution can be implemented. This operation is expected to start in November 2000. A Fire Hazard Analysis (FHA) is required for all new facilities and all nonreactor nuclear facilities, in accordance with U.S. Department of Energy (DOE) Order 5480.7A, Fire Protection. This FHA has been prepared in accordance with DOE 5480.7A and HNF-PRO-350, Fire Hazard Analysis Requirements. Additionally, requirements or criteria contained in DOE, Richland Operations Office (RL) RL Implementing Directive (RLID) 5480.7, Fire Protection, or other DOE documentation are cited, as applicable. This FHA comprehensively assesses the risk of fire at the CVDF to ascertain whether the specific objectives of DOE 5480.7A are met. These specific fire protection objectives are: (1) Minimize the potential for the occurrence of a fire. (2) Ensure that fire does not cause an onsite or offsite release of radiological and other hazardous material that will threaten the public health and safety or the environment. (3) Establish requirements that will provide an acceptable degree of life safety to DOE and contractor personnel and ensure that there are no undue hazards to the public from fire and its effects in DOE facilities. (4) Ensure that vital DOE programs will not suffer unacceptable delays as a result of fire and related perils. (5) Ensure that property damage from fire and related perils does not exceed an acceptable level. (6) Ensure that process control and safety systems are not damaged by fire or related perils. This FHA is based on the facility as constructed and with planned operation at the time of document preparation. Changes in facility planned and actual operation require that the identified fire risks associated with the CVDF be re-evaluated. Consequently, formal documentation and future revision of this FHA may be required.

SINGH, G.

2000-09-06T23:59:59.000Z

323

A methodology for performance and compatibility evaluation of an all-digital substation protection system  

E-Print Network (OSTI)

A power system protection system consists, at least, of an instrument trans- former, a protective device (relay), and a circuit breaker. Conventional instrument transformers bring currents and voltages from power network levels to much lower scaled-down replicas that serve as input signals to protective relays. The relay's function is to measure input signals (or a relationship among them in some cases) and compare them to defined operating characteristic thresholds (relay settings) to quickly decide whether to operate associated circuit breaker(s). Existing protection systems within a substation are based on a hardwired interface between instrument transformers and protective relays. Recent development of electronic instrument transformers and the spread of digital relays allow the development of an all-digital protection system, in which the traditional analog interface has been replaced with a digital signal connected to digital relays through a digital communication link (process bus). Due to their design, conventional instrument transformers introduce distortions to the current and voltage signal replicas. These distortions may cause protective relays to misoperate. On the other hand, non-conventional instrument transformers promise distortion-free replicas, which, in turn, should translate into better relay performance. Replacing hardwired signals with a communication bus also reduces the significant cost associated with copper wiring. An all-digital system should provide compatibility and interoperability so that different electronic instrument transformers can be connected to different digital relays (under a multi-vendor connection) Since the novel all-digital system has never been implemented and/or tested in practice so far, its superior performance needs to be evaluated. This thesis proposes a methodology for performance and compatibility evaluation of an all-digital protection system through application testing. The approach defines the performance indices and compatibility indices as well as the evaluation methodology.

Portillo Urdaneta, Levi

2006-12-01T23:59:59.000Z

324

[Engineering development of advanced coal-fired low-emission boiler systems]. Technical progress report, October--December 1995  

Science Conference Proceedings (OSTI)

The overall objective of the Project is the expedited commercialization of advanced coal-fired low-emisssion boiler systems. The primary objectives are: NO{sub x} emissions, lb/million Btu; SO{sub 2} emissions, lb/million Btu; particulate emissions, lb/million Btu; and net plant efficiency, not less than 42%. The secondary objectives are: improved ash disposability; reduced waste generation; and reduced air toxics emissions. Accomplishments to date are summarized for the following tasks: task 1, project planning and management; task 7, component development and optimization; task 8, preliminary POC test facility design; task 9, subsystem test design and plan; task 10, subsystem test unit construction; and task 11, subsystem test operation and evaluation.

Wesnor, J.D.; Bakke, E. [ABB Environmental Systems, Birmingham, AL (United States); Bender, D.J.; Kaminski, R.S. [Raytheon Engineers and Constructors, Inc., Philadelphia, PA (United States)

1995-12-31T23:59:59.000Z

325

Enhancing Carbon Reactivity in Mercury Control in Lignite-Fired Systems  

Science Conference Proceedings (OSTI)

This project was awarded through the U.S. Department of Energy (DOE) National Energy Technology Laboratory Program Solicitation DE-PS26-03NT41718-01. The Energy & Environmental Research Center (EERC) led a consortium-based effort to resolve mercury (Hg) control issues facing the lignite industry. The EERC team-the Electric Power Research Institute (EPRI); the URS Corporation; the Babcock & Wilcox Company; ADA-ES; Apogee; Basin Electric Power Cooperative; Otter Tail Power Company; Great River Energy; Texas Utilities; Montana-Dakota Utilities Co.; Minnkota Power Cooperative, Inc.; BNI Coal Ltd.; Dakota Westmoreland Corporation; the North American Coal Corporation; SaskPower; and the North Dakota Industrial Commission-demonstrated technologies that substantially enhanced the effectiveness of carbon sorbents to remove Hg from western fuel combustion gases and achieve a high level ({ge} 55% Hg removal) of cost-effective control. The results of this effort are applicable to virtually all utilities burning lignite and subbituminous coals in the United States and Canada. The enhancement processes were previously proven in pilot-scale and limited full-scale tests. Additional optimization testing continues on these enhancements. These four units included three lignite-fired units: Leland Olds Station Unit 1 (LOS1) and Stanton Station Unit 10 (SS10) near Stanton and Antelope Valley Station Unit 1 (AVS1) near Beulah and a subbituminous Powder River Basin (PRB)-fired unit: Stanton Station Unit 1 (SS1). This project was one of three conducted by the consortium under the DOE mercury program to systematically test Hg control technologies available for utilities burning lignite. The overall objective of the three projects was to field-test and verify options that may be applied cost-effectively by the lignite industry to reduce Hg emissions. The EERC, URS, and other team members tested sorbent injection technologies for plants equipped with electrostatic precipitators (ESPs) and spray dryer absorbers combined with fabric filters (SDAs-FFs). The work focused on technology commercialization by involving industry and emphasizing the communication of results to vendors and utilities throughout the project.

Chad Wocken; Michael Holmes; John Pavlish; Jeffrey Thompson; Katie Brandt; Brandon Pavlish; Dennis Laudal; Kevin Galbreath; Michelle Olderbak

2008-06-30T23:59:59.000Z

326

Development of a reconfigurable protective system for multi-rotor UAS  

Science Conference Proceedings (OSTI)

The purpose of this study is to illustrate how the design and deployment of a minimal protective system for multi-rotorcraft can cater for changes in legislation and provide for greater use both in and outdoors. A methodology is presented to evaluate ... Keywords: autonomous system, landing gear, reconfigurable system, unmanned aerial vehicles

Thomas Irps; Stephen Prior; Darren Lewis

2011-07-01T23:59:59.000Z

327

Take your career to the next level with a bachelor's degree in Fire and Emergency Services Administration. Fire and emergency personnel have  

E-Print Network (OSTI)

Overview Take your career to the next level with a bachelor's degree in Fire and Emergency Services Administration. Fire and emergency personnel have a long and proud history of providing communities with a wide variety of fire protection, fire prevention, emergency medical, and emergency preparedness services

328

Engineered Fire Safety Group  

Science Conference Proceedings (OSTI)

Engineered Fire Safety Group. Welcome. ... Employment/Research Opportunities. Contact. Jason Averill, Leader. Engineered Fire Safety Group. ...

2012-06-05T23:59:59.000Z

329

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Comparison of Combustion Characteristics of Crude Oils Using Cone Calorimeter. ... fire safety; fire research; crude oil; cone calorimeters; combustion ...

330

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Keywords: fire research; fire science; smoke plumes; crude oil; water; in situ combustion; oil spills Abstract: Under the sponsorship ...

331

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... methodology; fire safety; fire investigations; wind tunnels ... towers to withstand unanticipated events such as ... wind tunnel studies conducted in 2002 ...

332

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... fires; computational fluid dynamics; predictive models; field models; fire models; hazard assessment; nuclear power plants; nuclear reactor safety ...

333

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Evaluation of Fire Models for Nuclear Power Plant Applications: Cable ... cable trays; fire models; nuclear power plants; computer models; ventilation ...

334

Fire Research Grants Program  

Science Conference Proceedings (OSTI)

Fire Research awards are open to institutions of higher education; hospitals; non-profit organizations ... The National Fire Research Laboratory. ...

2013-08-23T23:59:59.000Z

335

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Measurements for Fire Detection by Mean of Gas Sensors in an Insulation Material Factory. Measurements for Fire Detection ...

336

Engineering development of advanced coal-fired low-emission boiler systems. Technical progress report No. 4, July--September 1993  

Science Conference Proceedings (OSTI)

The overall objective of the Project is the expedited commercialization of advanced coal-fired low-emission boiler systems. The specified primary objectives are: NOx emissions not greater than one-third NSPS; SOx emissions not greater than one-third NSPS; and particulate emissions not greater than one-half NSPS. The specific secondary objectives are: improved ash disposability and reduced waste generation; reduced air toxics emissions; and increased generating efficiency. The final deliverables are a design data base that will allow future coal-fired power plants to meet the stated objectives and a preliminary design of a commercial generation unit.

Not Available

1993-12-29T23:59:59.000Z

337

Fault diagnosis for the feedwater heater system of a 300MW coal-fired power generating unit based on RBF neural network  

Science Conference Proceedings (OSTI)

In this paper, a new style radial basis function (RBF) neural network is used for fault diagnosis of the high-pressure feed-water heater system of a coal-fired power generating unit. The structure of the RBF network and its training algorithm are given. ...

Liangyu Ma; Yongguang Ma; Jin Ma

2005-08-01T23:59:59.000Z

338

No moving parts safe and arm apparatus and method with monitoring and built-in-test for optical firing of explosive systems  

DOE Patents (OSTI)

A laser initiated ordnance controller apparatus which provides a safe and arm scheme with no moving parts. The safe and arm apparatus provides isolation of firing energy to explosive devices using a combination of polarization isolation and control through acousto-optical deviation of laser energy pulses. The apparatus provides constant monitoring of the systems status and performs 100% built-in-test at any time prior to ordnance ignition without the risk of premature ignition or detonation. The apparatus has a computer controller, a solid state laser, an acousto-optic deflector and RF drive circuitry, built-in-test optics and electronics, and system monitoring capabilities. The optical system is completed from the laser beam power source to the pyrotechnic ordnance through fiber optic cabling, optical splitters and optical connectors. During operation of the apparatus, a command is provided by the computer controller and, simultaneous with laser flashlamp fire, the safe and arm device is opened for approximately 200 microseconds which allows the laser pulse to transmit through the device. The arm signal also energizes the laser power supply and activated the acousto-optical deflector. When the correct fire format command is received, the acousto-optic deflector moves to the selected event channel and the channel is verified to ensure the system is pointing to the correct position. Laser energy is transmitted through the fiber where an ignitor or detonator designed to be sensitive to optical pulses is fired at the end of the fiber channel.

Hendrix, J.L.

1994-12-31T23:59:59.000Z

339

Proceedings of the joint contractors meeting: FE/EE Advanced Turbine Systems conference FE fuel cells and coal-fired heat engines conference  

SciTech Connect

The joint contractors meeting: FE/EE Advanced Turbine Systems conference FEE fuel cells and coal-fired heat engines conference; was sponsored by the US Department of Energy Office of Fossil Energy and held at the Morgantown Energy Technology Center, P.O. Box 880, Morgantown, West Virginia 26507-0880, August 3--5, 1993. Individual papers have been entered separately.

Geiling, D.W. [ed.

1993-08-01T23:59:59.000Z

340

Discrete-event modelling of fire spreading  

Science Conference Proceedings (OSTI)

We deal here with the application of discrete-event System Specification (DEVS) formalism to implement a semi-physical fire spread model. Currently, models from physics finely representing forest fires are not efficient and still under development. If ... Keywords: Cellular models, DEVS, Discrete-event modelling and simulation, Fire spread

Alexandre Muzy; Eric Innocenti; Antoine Aiello; Jean-François Santucci; Thierry Marcelli; Paul Antoine Santoni

2008-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Advanced turbine systems program conceptual design and product development task 5 -- market study of the gas fired ATS. Topical report  

DOE Green Energy (OSTI)

Solar Turbines Incorporated (Solar), in partnership with the Department of Energy, will develop a family of advanced gas turbine-based power systems (ATS) for widespread commercialization within the domestic and international industrial marketplace, and to the rapidly changing electric power generation industry. The objective of the jointly-funded Program is to introduce an ATS with high efficiency, and markedly reduced emissions levels, in high numbers as rapidly as possible following introduction. This Topical Report is submitted in response to the requirements outlined in Task 5 of the Department of Energy METC Contract on Advanced Combustion Systems, Contract No, DE AC21-93MC30246 (Contract), for a Market Study of the Gas Fired Advanced Turbine System. It presents a market study for the ATS proposed by Solar, and will examine both the economic and siting constraints of the ATS compared with competing systems in the various candidate markets. Also contained within this report is an examination and analysis of Solar`s ATS and its ability to compete in future utility and industrial markets, as well as factors affecting the marketability of the ATS.

NONE

1995-05-01T23:59:59.000Z

342

Functional issues and environmental qualification of digital protection systems of advanced light-water nuclear reactors  

Science Conference Proceedings (OSTI)

Issues of obsolescence and lack of infrastructural support in (analog) spare parts, coupled with the potential benefits of digital systems, are driving the nuclear industry to retrofit analog instrumentation and control (I&C) systems with digital and microprocessor-based systems. While these technologies have several advantages, their application to safety-related systems in nuclear power plants raises key issues relating to the systems` environmental qualification and functional reliability. To bound the problem of new I&C system functionality and qualification, the authors focused this study on protection systems proposed for use in ALWRs. Specifically, both functional and environmental qualification issues for ALWR protection system I&C were addressed by developing an environmental, functional, and aging data template for a protection division of each proposed ALWR design. By using information provided by manufacturers, environmental conditions and stressors to which I&C equipment in reactor protection divisions may be subjected were identified. The resulting data were then compared to a similar template for an instrument string typically found in an analog protection division of a present-day nuclear power plant. The authors also identified fiber-optic transmission systems as technologies that are relatively new to the nuclear power plant environment and examined the failure modes and age-related degradation mechanisms of fiber-optic components and systems. One reason for the exercise of caution in the introduction of software into safety-critical systems is the potential for common-cause failure due to the software. This study, however, approaches the functionality problem from a systems point of view. System malfunction scenarios are postulated to illustrate the fact that, when dealing with the performance of the overall integrated system, the real issues are functionality and fault tolerance, not hardware vs. software.

Korsah, K.; Clark, R.L.; Wood, R.T. [Oak Ridge National Lab., TN (United States)

1994-04-01T23:59:59.000Z

343

EPRI/NRC-RES Fire Human Reliability Analysis Guidelines  

Science Conference Proceedings (OSTI)

In 2001, the Electric Power Research Institute (EPRI) and the U.S. Nuclear Regulatory Commission's Office of Nuclear Regulatory Research (NRC-RES), operating under a Memorandum of Understanding (MOU), collaborated to improve the state-of-the-art in fire risk assessment to support the new risk-informed environment in fire protection. This project produced a consensus documentNUREG/CR-6850 (EPRI report 1011989), Fire PRA Methodology for Nuclear Power Facilitieswhich addresses fire risk during operations at...

2012-07-24T23:59:59.000Z

344

A coal-fired combustion system for industrial process heating applications. Quarterly technical progress report, July 1993--September 1993  

SciTech Connect

This advanced combustion system research program is for the development of innovative coal-fired process heaters which can be used for high temperature melting, smelting and waste vitrification processes. The process heater systems to be developed have multiple use applications; however, the Phase 3 research effort is being focused on the development of a process heater system to be used for producing value added vitrified glass products from boiler/incinerator ashes and industrial wastes. The primary objective of the Phase 3 project is to develop and integrate all the system components, from fuel through total system controls, and then test the complete system in order to evaluate its potential marketability. During the past quarter, the major effort was completing some of the system modification installation designs, completing industry funded testing, developing a surrogate TSCA ash composition, and completing the TSCA ash Test Plan. The installation designs will be used for the equipment modifications planned for the end of CY 93. The industry funded testing consisted of vitrifying Spent Aluminum Potliner (SPL) which is a listed hazardous waste. This testing has verified that SPL can be vitrified into a safe, recyclable glass product. Some results from this testing are provided in Section 2.2.1. The surrogate TSCA ash composition was developed with input from various DOE laboratories and subcontractors. The surrogate ash consists of a mixture of MSW fly ash and bottom ash spiked with heavy metal contaminants. The levels of metal additives are sufficient to ascertain the partitioning of the contaminants between the glass and effluent flow streams. Details of the surrogate composition and the planned testing is provided in Section 4.2.2.

Not Available

1993-10-30T23:59:59.000Z

345

PISCES: an expert system for coal fired power plant monitoring and diagnostics  

Science Conference Proceedings (OSTI)

Economics and safety are two of the primary factors that influence the efficient operation of today's complicated power plants. The use of a computer expert system to assist in automatic plant system surveillance and diagnostics can reduce the operation ...

Eddie S. Washington; Moonis Ali

1988-06-01T23:59:59.000Z

346

Description and Verification of the NOAA Smoke Forecasting System: The 2007 Fire Season  

Science Conference Proceedings (OSTI)

An overview of the National Oceanic and Atmospheric Administration’s (NOAA) current operational Smoke Forecasting System (SFS) is presented. This system is intended as guidance to air quality forecasters and the public for fine particulate matter ...

Glenn D. Rolph; Roland R. Draxler; Ariel F. Stein; Albion Taylor; Mark G. Ruminski; Shobha Kondragunta; Jian Zeng; Ho-Chun Huang; Geoffrey Manikin; Jeffery T. McQueen; Paula M. Davidson

2009-04-01T23:59:59.000Z

347

Software implementation of hydraulic shock numerical computation in the pressure hydraulic systems without protection devices  

Science Conference Proceedings (OSTI)

This paper presents software for calculus of hydraulic shock phenomenon in pressure hydraulic systems without protection device. The program is written in Java programming language and responds to the following requirements: easy management of several ... Keywords: flowchart, graphical interface, hydraulic shock (water hammer), method of characteristics, pressure hydraulic system, software

Ichinur Omer

2010-08-01T23:59:59.000Z

348

Cyber Friendly Fire  

Science Conference Proceedings (OSTI)

Cyber friendly fire (FF) is a new concept that has been brought to the attention of Department of Defense (DoD) stakeholders through two workshops that were planned and conducted by the Air Force Research Laboratory (AFRL) and research conducted for AFRL by the Pacific Northwest National Laboratory. With this previous work in mind, we offer a definition of cyber FF as intentional offensive or defensive cyber/electronic actions intended to protect cyber systems against enemy forces or to attack enemy cyber systems, which unintentionally harms the mission effectiveness of friendly or neutral forces. Just as with combat friendly fire, a fundamental need in avoiding cyber FF is to maintain situation awareness (SA). We suggest that cyber SA concerns knowledge of a system's topology (connectedness and relationships of the nodes in a system), and critical knowledge elements such as the characteristics and vulnerabilities of the components that comprise the system (and that populate the nodes), the nature of the activities or work performed, and the available defensive (and offensive) countermeasures that may be applied to thwart network attacks. A training implication is to raise awareness and understanding of these critical knowledge units; an approach to decision aids and/or visualizations is to focus on supporting these critical knowledge units. To study cyber FF, we developed an unclassified security test range comprising a combination of virtual and physical devices that present a closed network for testing, simulation, and evaluation. This network offers services found on a production network without the associated costs of a real production network. Containing enough detail to appear realistic, this virtual and physical environment can be customized to represent different configurations. For our purposes, the test range was configured to appear as an Internet-connected Managed Service Provider (MSP) offering specialized web applications to the general public. The network is essentially divided into a production component that hosts the web and network services, and a user component that hosts thirty employee workstations and other end devices. The organization's network is separated from the Internet by a Cisco ASA network security device that both firewalls and detects intrusions. Business sensitive information is stored in various servers. This includes data comprising thousands of internal documents, such as finance and technical designs, email messages for the organization's employees including the CEO, CFO, and CIO, the organization's source code, and Personally Identifiable client data. Release of any of this information to unauthorized parties would have a significant, detrimental impact on the organization's reputation, which would harm earnings. The valuable information stored in these servers pose obvious points of interest for an adversary. We constructed several scenarios around this environment to support studies in cyber SA and cyber FF that may be run in the test range. We describe mitigation strategies to combat cyber FF including both training concepts and suggestions for decision aids and visualization approaches. Finally, we discuss possible future research directions.

Greitzer, Frank L.; Carroll, Thomas E.; Roberts, Adam D.

2011-09-01T23:59:59.000Z

349

ETTM: Low Voltage System Protection and Coordination Computer-Based Training Version 1.0  

Science Conference Proceedings (OSTI)

ETTM Low Voltage System Protection and Coordination is a computer-based training module that allows users to access training when desired and review it at their own pace. It provides graphics and limited interactive features to enhance learning. Low voltage power systems are generally classified as AC power systems operating at the 120 600 Volt level. Because they often serve a large number of diverse loads in residences, businesses, and power plants, low voltage power systems present a unique set of cha...

2010-11-30T23:59:59.000Z

350

Fire Testing of High-Density Polyethylene Pipe  

Science Conference Proceedings (OSTI)

The results in this report are intended to demonstrate a method that can be used to protect high-density polyethylene (HDPE) piping located aboveground from postulated fire events. This includes protecting both pipe and pipe fittings (for example, elbows, tees, and valves) from the fire environmentincluding the heat transmitted from pipe supportsand preventing the fire environment from passing through building wall or floor penetrations. The report is intended to be complementary to other ongoing Electr...

2011-08-23T23:59:59.000Z

351

Cermet composite thermal spray coatings for erosion and corrosion protection in combustion environments of advanced coal-fired boilers. Semiannual technical report, January 14, 1997--August 14, 1997  

SciTech Connect

Research is presently being conducted to determine the optimum ceramic/metal combination in thermally sprayed metal matrix composite coatings for erosion and corrosion resistance in new coal-fired boilers. The research will be accomplished by producing model cermet composites using powder metallurgy and electrodeposition methods in which the effect of ceramic/metal combination for the erosion and corrosion resistance will be determined. These results will provide the basis for determining the optimum hard phase constituent size and volume percent in thermal spray coatings. Thermal spray coatings will be applied by our industrial sponsor and tested in our erosion and corrosion laboratories. Bulk powder processed Ni-Al{sub 2}O{sub 3} composites were produced at Idaho National Engineering Laboratory. The composite samples contained 0, 21, 27, 37, and 45 volume percent Al{sub 2}O{sub 3} with an average particle size of 12 um. Also, to deposit model Ni-Al{sub 2}O{sub 3} coatings, an electrodeposition technique was developed and coatings with various volume fractions (0-35%) of Al{sub 2}O{sub 3} were produced. The powder and electrodeposition processing of Ni-Al{sub 2}O{sub 3} Composites provide the ability to produce two phase microstructure without changing the microstructure of the matrix material. Therefore, the effect of hard second phase particles size and volume fraction on erosion resistance could be analyzed.

Schorr, B.S.; Levin, B.F.; DuPont, J.N.; Marder, A.R.

1997-08-31T23:59:59.000Z

352

Fire suppression and detection equipment  

SciTech Connect

Inspection and testing guidelines go beyond the 'Code of Federal Regulation'. Title 30 of the US Code of Federal Regulations (30 CFR) contains requirements and references to national standards for inspection, testing and maintenance of fire suppression and detection equipment for mine operators. However, federal requirements have not kept pace with national standards and best practices. The article lists National Fire Protection (NFPA) standards that are referenced by the US Mine Safety and Health Administration (MSHA) in 30 CFR. It then discusses other NFPA Standards excluded from 30 CFR and explains the NFPA standard development process. 2 refs., 3 tabs., 5 photos.

E.E. Bates [HSB Professional Loss Control, Lexington, KY (United States)

2006-01-15T23:59:59.000Z

353

Energy-Saving Analysis on Thermal System in 600MW Supercritical Coal-Fired Power Plants  

Science Conference Proceedings (OSTI)

High-efficiency, energy-saving and environmentally friendly supercritical thermal power units are gradually becoming main stream in China. In this paper, an advanced energy system analysis method, specific consumption analysis, is used to examine the ... Keywords: supercritical, energy-saving, specific consumption analysis, feed-water heating system, environmentally friendly

Yongping Yang; Yu Wu; Zhiping Yang; Ningling Wang; Gang Xu

2010-06-01T23:59:59.000Z

354

Advanced Turbine Systems Program conceptual design and product development. Task 3.0, Selection of natural gas-fired Advanced Turbine System  

DOE Green Energy (OSTI)

This report presents results of Task 3 of the Westinghouse ATS Phase II program. Objective of Task 3 was to analyze and evaluate different cycles for the natural gas-fired Advanced Turbine Systems in order to select one that would achieve all ATS program goals. About 50 cycles (5 main types) were evaluated on basis of plant efficiency, emissions, cost of electricity, reliability-availability-maintainability (RAM), and program schedule requirements. The advanced combined cycle was selected for the ATS plant; it will incorporate an advanced gas turbine engine as well as improvements in the bottoming cycle and generator. Cost and RAM analyses were carried out on 6 selected cycle configurations and compared to the baseline plant. Issues critical to the Advanced Combined Cycle are discussed; achievement of plant efficiency and cost of electricity goals will require higher firing temperatures and minimized cooling of hot end components, necessitating new aloys/materials/coatings. Studies will be required in combustion, aerodynamic design, cooling design, leakage control, etc.

NONE

1994-12-01T23:59:59.000Z

355

Protective Relays: Numerical Protective Relays  

Science Conference Proceedings (OSTI)

Protective relays are decision-making elements in the protection scheme for electrical power systems. Numerical relays offer many advantages over the traditional electromechanical types of devices. This guide provides an overview of numerical relays and discusses maintenance and testing.

2004-12-22T23:59:59.000Z

356

MACHINE PROTECTION SYSTEM FOR CONCURRENT OPERATION OF RHIC AND BLIP.  

SciTech Connect

The Brookhaven 200MeV linac is a multipurpose machine used to inject low intensity polarized protons for RHIC (Relativistic Heavy Ion Collider), as well as to inject high intensity protons to BLIP (Brookhaven Linac Isotope Producer), a medical isotope production facility. If high intensity protons were injected to RHIC by mistake, administrative radiation limits could be exceeded or sensitive electronics could be damaged. In the past, the changeover from polarized proton to high intensity proton operation has been a lengthy process, thereby never allowing the two programs to run simultaneously. To remedy this situation and allow concurrent operation of RHIC and BLIP, an active interlock system has been designed to monitor current levels in the AGS using two current transformers with fail safe circuitry and associated electronics to inhibit beam to RHIC if high intensity currents are detected.

WILINSKI, M.; BELLAVIA, S.; GLENN, J.W.; MAUSNER, L.F.; UNGER, K.L.

2005-05-16T23:59:59.000Z

357

Fire suppressing apparatus. [sodium fires  

DOE Patents (OSTI)

Apparatus for smothering a liquid sodium fire comprises a pan, a perforated cover on the pan, and tubed depending from the cover and providing communication between the interior of the pan and the ambient atmosphere through the perforations in the cover. Liquid caught in the pan rises above the lower ends of the tubes and thus serves as a barrier which limits the amount of air entering the pan.

Buttrey, K.E.

1980-12-19T23:59:59.000Z

358

Multiwavelength Observations of a Developing Cloud System: The FIRE II 26 November 1991 Case Study  

Science Conference Proceedings (OSTI)

Simultaneous multiwavelength measurements of a developing cloud system were obtained by NOAA Doppler lidar, Doppler radar, Fourier transform infrared interferometer, and microwave and infrared radiometers on 26 November 1991. The evolution of the ...

J. M. Intrieri; W. L. Eberhard; T. Uttal; J. A. Shaw; J. B. Snider; Y. Han; B. W. Orr; S. Y. Matrosov

1995-12-01T23:59:59.000Z

359

Test Plan to Assess Fire Effects on the Function of an Engineered Surface Barrier  

Science Conference Proceedings (OSTI)

Wildfire is a frequent perturbation in shrub steppe ecosystems, altering the flora, fauna, atmosphere, and soil of these systems. Research on the fire effects has focused mostly on natural ecosystems with essentially no attention on engineered systems like surface barriers. The scope of the project is to use a simulated wildfire to induce changes in an engineered surface barrier and document the effects on barrier performance. The main objective is to quantify the effects of burning and the resulting post-fire conditions on alterations in soil physical properties; hydrologic response, particularly the water balance; geochemical properties; and biological properties. A secondary objective is to use the lessons learned to maximize fire protection in the design of long-term monitoring systems based on electronic sensors. A simulated wildfire will be initiated, controlled and monitored at the 200-BP-1 barrier in collaboration with the Hanford Fire Department during the fall of 2008. The north half of the barrier will be divided into nine 12 x 12 m plots, each of which will be randomly assigned a fuel load of 2 kg m-2 or 4 kg m-2. Each plot will be ignited around the perimeter and flames allowed to carry to the centre. Any remaining unburned vegetation will be manually burned off using a drip torch. Progress of the fire and its effects will be monitored using point measurements of thermal, hydrologic, and biotic variables. Three measures of fire intensity will be used to characterize fire behavior: (1) flame height, (2) the maximum temperature at three vertical profile levels, and (3) total duration of elevated temperature at these levels. Pre-burn plant information, including species diversity, plant height, and canopy diameter will be measured on shrubs from the plots to be burned and from control plots at the McGee ranch. General assessments of shrub survival, recovery, and recruitment will be made after the fire. Near-surface soil samples will be collected pre- and post-burn to determine changes in the gravel content of the surface layer so as to quantify inflationary or deflationary responses to fire and to reveal the ability of the surface to resist post-fire erosive stresses. Measures of bulk density, water repellency, water retention, and hydraulic conductivity will be used to characterize changes in infiltration rates and water storage capacity following the fire. Samples will also be analyzed to quantify geochemical changes including changes in soil pH, cation exchange capacity, specific surface area, and the concentration of macro nutrients (e.g. N, P, K) and other elements such as Na, Mg, Ca, that are critical to the post-fire recovery revegetation. Soil CO2 emissions will be measured monthly for one year following the burn to document post-fire stimulation of carbon turnover and soil biogenic emissions. Surface and subsurface temperature measurements at and near monitoring installations will be used to document fire effects on electronic equipment. The results of this study will be used to bridge the gaps in knowledge on the effects of fire on engineered ecosystems (e.g. surface barriers), particularly the hydrologic and biotic characteristics that govern the water and energy balance. These results will also support the development of practical fire management techniques for barriers that are compatible with wildfire suppression strategies. Furthermore, lessons learned will be use to develop installation strategies needed to protect electronic monitoring equipment from the intense heat of fire and the potential damaging effects of smoke and fire extinguishing agents. Such information is needed to better understand long-term barrier performance under extreme conditions, especially if site maintenance and operational funding is lost for activities such as barrier revegetation.

Ward, Anderson L.; Berlin, Gregory T.; Cammann, Jerry W.; Leary, Kevin D.; Link, Steven O.

2008-09-29T23:59:59.000Z

360

LARGE-SCALE MECURY CONTROL TECHNOLOGY TESTING FOR LIGNITE-FIRED UTILITIES-OXIDATION SYSTEMS FOR WET FGD  

SciTech Connect

The Energy & Environmental Research Center (EERC) is conducting a consortium-based effort directed toward resolving the mercury (Hg) control issues facing the lignite industry. Specifically, the EERC team--the EERC, EPRI, URS, ADA-ES, Babcock & Wilcox, the North Dakota Industrial Commission, SaskPower, and the Mercury Task Force, which includes Basin Electric Power Cooperative, Otter Tail Power Company, Great River Energy, Texas Utilities (TXU), Montana-Dakota Utilities Co., Minnkota Power Cooperative, BNI Coal Ltd., Dakota Westmoreland Corporation, and the North American Coal Company--has undertaken a project to significantly and cost-effectively oxidize elemental mercury in lignite combustion gases, followed by capture in a wet scrubber. This approach will be applicable to virtually every lignite utility in the United States and Canada and potentially impact subbituminous utilities. The oxidation process is proven at the pilot-scale and in short-term full-scale tests. Additional optimization is continuing on oxidation technologies, and this project focuses on longer-term full-scale testing. The lignite industry has been proactive in advancing the understanding of and identifying control options for Hg in lignite combustion flue gases. Approximately 1 year ago, the EERC and EPRI began a series of Hg-related discussions with the Mercury Task Force as well as utilities firing Texas and Saskatchewan lignites. This project is one of three being undertaken by the consortium to perform large-scale Hg control technology testing to address the specific needs and challenges to be met in controlling Hg from lignite-fired power plants. This project involves Hg oxidation upstream of a system equipped with an electrostatic precipitator (ESP) followed by wet flue gas desulfurization (FGD). The team involved in conducting the technical aspects of the project includes the EERC, Babcock & Wilcox, URS, and ADA-ES. The host sites include Minnkota Power Cooperative Milton R. Young Unit 2 and TXU Monticello Unit 3. The work involves establishing Hg oxidation levels upstream of air pollution control devices (APCDs) and removal rates across existing ESP and FGD units, determining costs associated with those removal rates, investigating the possibility of the APCD acting as a multipollutant control device, quantifying the balance of plant impacts of the control technologies, and facilitating technology commercialization.

Michael J. Holmes; Steven A. Benson; Jeffrey S. Thompson

2004-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Protecting a HVDC link against accidental isolation from its receiving AC system  

SciTech Connect

When an HVdc scheme is isolated from its receiving ac system, the inverter may continue to operate, generating its own ac bus voltages; this is defined here as islanding. If islanding is allowed to continue unrestricted, then main circuit components may in some conditions be damaged and it is therefore necessary to provide a suitable protection system. This paper outlines the protection scheme developed for the McNeill Back-to-Back HVdc link in Alberta, Canada, to prevent damage due to islanding while still permitting the link to automatically restart on reclosure of the isolating breaker. Oscillograms showing the protection in operation on both the GEC ALSTHOM HVdc simulator and during tests carried out as part of the commissioning of the McNeill HV dc link are included.

Whitehouse, R.S. (GEC Alsthom Transmission and Distribution Projects Ltd., Stafford (United Kingdom))

1993-07-01T23:59:59.000Z

362

Study of transmission and protection elements for wind energy generating systems. Volume 1  

DOE Green Energy (OSTI)

Results are reported of a study at Cornell University on transmission, distribution, and protection systems for large wind-energy generators (WEG) connected to an electric utility grid. Configurations for wind farms on flat terrain, mountain-peak clusters, and installations along a ridge were examined. Computer studies of load-flow and short-circuit behavior confirmed the technical feasibility of the proposed systems. Realistic unit costs for the projected transmission and protection schemes range from $109 to $317 per Kw, depending upon choice of configuration and distance from the grid. Cost of protective equipment is found to be a major factor in most cases, tending to be equal or greater than transmission line costs when the WEG units are located five miles or less from the grid. Several alternatives are suggested for future study.

Linke, S; Teshome, A; Yehsakul, P D

1978-04-01T23:59:59.000Z

363

Insider protection  

SciTech Connect

The government community is broadly addressing the insider threat. The first section of this paper defines protection approaches and the latter sections present various applicable technology developments. The bulk of the paper discusses technology developments applied to (1) personnel and material tracking and inventory, (2) classified document protection, and (3) protecting security systems. The personnel and material tracking system uses a PC based-host to (1) collect information from proximity tags and material movement sensors, (2) apply rules to this input to assure that the ongoing activity meets the site selectable rules and, (3) forward the results to either an automated inventory system or an alarm system. The document protection system uses a PC network to efficiently and securely control classified material which is stored on write-once-read-mostly optical media. The protection of sensor to multiplexer communications in a security system is emphasized in the discussion of protecting security systems.

Waddoups, I.G.

1993-07-01T23:59:59.000Z

364

Program: Fire Risk Reduction in Communities  

Science Conference Proceedings (OSTI)

... spread in order to develop science-based standards, codes, and practices for fire resistant communities and 2) incorporate cyber-physical systems ...

2013-01-09T23:59:59.000Z

365

ANALYSIS OF BUILDING AND FIRE CODES AND ...  

Science Conference Proceedings (OSTI)

... Fire alarm systems • Manual initiation for occupant notification ... Pumps and piping Page 35. ... Fuel pipe-in-pipe draining to catch basin with alarm ...

2013-04-26T23:59:59.000Z

366

A NOVEL DEVICE FOR DISSEMINATING FIRE ...  

Science Conference Proceedings (OSTI)

... streaming agent. For it to work effectively, the location of the fire must be known ahead of time in order to orient the system Halon ...

2011-10-20T23:59:59.000Z

367

1. Introduction 2. Fire suppression mechanisms  

Science Conference Proceedings (OSTI)

... may be similar to an outdoor fire, except for wind influence. b ... to installation of a water mist system in the turbine hoods of the offshore platforms of ...

2011-10-27T23:59:59.000Z

368

Application of Flame Doctor to T-Fired Boilers: Feasibility Study  

Science Conference Proceedings (OSTI)

Flame Doctor, a burner diagnostic technology, is a packaged system consisting of hardware and software that ties into existing burner flame scanner systems of wall-fired, cyclone-fired, and turbo-fired boilers to provide real-time assessment of flame quality. This report describes feasibility tests to evaluate Flame Doctor for extension to tangentially fired (T-fired) boiler applications.

2007-03-22T23:59:59.000Z

369

Aspects of design, test and validation of the software for a computerized reactor protection system  

Science Conference Proceedings (OSTI)

In safety-oriented applications, the software has to fulfil certain stringent reliability requirements. In order to determine the reliability of the software, a variety of different methods can be used. The methods used for the reliability proof of a ... Keywords: Program testing, Proof of correctness, Protection system

U. Voges

1976-10-01T23:59:59.000Z

370

The Protection System for the Superconducting Elements of the Large Hadron Collider at CERN  

E-Print Network (OSTI)

The protection system for the superconducting elements of the Large Hadron Collider (LHC) [1] at the European Laboratory for Particle Physics (CERN), and its associated equipment are presented: quench detectors, cold diodes, quench heaters and related power supplies, extraction resistors and associated current breakers. Features such as radiation resistance, redundancy and required reliability are discussed.

Dahlerup-Petersen, K; Gómez-Costa, J L; Hagedorn, Dietrich; Proudlock, Paul; Rodríguez-Mateos, F; Schmidt, R; Sonnemann, F

1999-01-01T23:59:59.000Z

371

Numerical simulation of hydraulic shock in a water pumping system protected by air  

Science Conference Proceedings (OSTI)

Air may be efficiently used in water pumping system protection from hydraulic shock, due to its elasticity. The paper presents the results regarding the extreme pressures in the discharge duct of a pumping installation, obtained by numerical simulation ... Keywords: air chamber, biphasic flow, dissolution, hydraulic shock, pumping installation

Anca Constantin; Claudiu Stefan Nitescu

2010-10-01T23:59:59.000Z

372

A frequency monitoring system development for wide-area power grid protection  

Science Conference Proceedings (OSTI)

There have been recent research activities on GPS-based FNET to prevent wide-area blackouts by monitoring frequency deviation. This paper introduces a system for monitoring regional frequencies in power grid developed as an advanced research project ... Keywords: Frequency monitoring, Power grid protection, Wide-area power grid

Yoon Sang Kim; Junho Ko; Dong-Kwang Shin; Chul-Hwan Kim; Chul-Won Park

2013-06-01T23:59:59.000Z

373

No moving parts safe & arm apparatus and method with monitoring and built-in-test for optical firing of explosive systems  

DOE Patents (OSTI)

A laser initiated ordnance controller apparatus which provides a safe and m scheme with no moving parts. The safe & arm apparatus provides isolation of firing energy to explosive devices using a combination of polarization isolation and control through acousto-optical deviation of laser energy pulses. The apparatus provides constant monitoring of the systems status and performs 100% built-in-test at any time prior to ordnance ignition without the risk of premature ignition or detonation. The apparatus has a computer controller, a solid state laser, an acousto-optic deflector and RF drive circuitry, built-in-test optics and electronics, and system monitoring capabilities. The optical system is completed from the laser beam power source to the pyrotechnic ordnance through fiber optic cabling, optical splitters and optical connectors. During operation of the apparatus, a command is provided by the computer controller and, simultaneous with laser flashlamp fire, the safe & arm device is opened for approximately 200 microseconds which allows the laser pulse to transmit through the device. The arm signal also energizes the laser power supply and activates the acousto-optical deflector. When the correct fire format command is received, the acousto-optic deflector moves to the selected event channel, and the channel is verified to ensure the system is pointing to the correct position. Laser energy is transmitted through the fiber where an ignitor or detonator designed to be sensitive to optical pulses is fired at the end of the fiber channel. Simultaneous event channels may also be utilized by optically splitting a single event channel. The built-in-test may be performed anytime prior to ordnance ignition.

Hendrix, James L. (Overland Park, KS)

1995-01-01T23:59:59.000Z

374

Engineering development of advanced coal-fired low-emission boiler systems. Technical progress report No. 15, April 15 1996--June 1996  

SciTech Connect

The Pittsburgh Energy Technology center of the US Department of Energy (DOE) has contracted with Combustion Engineering; Inc. (ABB CE) to perform work on the {open_quotes}Engineering Development of Advanced Coal-Fired Low-Emission Boiler Systems{close_quote} Project and has authorized ABB CE to complete Phase I on a cost-reimbursable basis and Phases II and III on a cost-share basis.

1996-08-19T23:59:59.000Z

375

No moving parts safe & arm apparatus and method with monitoring and built-in-test for optical firing of explosive systems  

DOE Patents (OSTI)

A laser initiated ordnance controller apparatus which provides a safe and arm scheme with no moving parts. The safe & arm apparatus provides isolation of firing energy to explosive devices using a combination of polarization isolation and control through acousto-optical deviation of laser energy pulses. The apparatus provides constant monitoring of the systems status and performs 100% built-in-test at any time prior to ordnance ignition without the risk of premature ignition or detonation. The apparatus has a computer controller, a solid state laser, an acousto-optic deflector and RF drive circuitry, built-in-test optics and electronics, and system monitoring capabilities. The optical system is completed from the laser beam power source to the pyrotechnic ordnance through fiber optic cabling, optical splitters and optical connectors. During operation of the apparatus, a command is provided by the computer controller and, simultaneous with laser flashlamp fire, the safe & arm device is opened for approximately 200 microseconds which allows the laser pulse to transmit through the device. The arm signal also energizes the laser power supply and activates the acousto-optical deflector. When the correct fire format command is received, the acousto-optic deflector moves to the selected event channel, and the channel is verified to ensure the system is pointing to the correct position. Laser energy is transmitted through the fiber where an ignitor or detonator designed to be sensitive to optical pulses is fired at the end of the fiber channel. Simultaneous event channels may also be utilized by optically splitting a single event channel. The built-in-test may be performed anytime prior to ordnance ignition. 6 figures.

Hendrix, J.L.

1995-04-11T23:59:59.000Z

376

The machine protection system for the R&D energy recovery LINAC  

SciTech Connect

The Machine Protection System (MPS) is a device-safety system that is designed to prevent damage to hardware by generating interlocks, based upon the state of input signals generated by selected sub-systems. It protects all the key machinery in the R&D Project called the Energy Recovery LINAC (ERL) against the high beam current. The MPS is capable of responding to a fault with an interlock signal within several microseconds. The ERL MPS is based on a National Instruments CompactRIO platform, and is programmed by utilizing National Instruments' development environment for a visual programming language. The system also transfers data (interlock status, time of fault, etc.) to the main server. Transferred data is integrated into the pre-existing software architecture which is accessible by the operators. This paper will provide an overview of the hardware used, its configuration and operation, as well as the software written both on the device and the server side.

Altinbas, Z.; Kayran, D.; Jamilkowski, J.; Lee, R.C.; Oerter, B.

2011-03-28T23:59:59.000Z

377

Verification and Validation of Selected Fire Models for Nuclear Power Plant Applications  

Science Conference Proceedings (OSTI)

This report documents the verification and validation (VV) of five selected fire models commonly used in support of risk-informed and performance-based (RI/PB) fire protection at nuclear power plants (NPPs).

2007-05-30T23:59:59.000Z

378

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... coal. Analysis of Fire Reports on File in the Massachusetts State Fire Marshal's Office Relating to Wood and Coal Heating Equipment. ...

379

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Crude Oil Full Scale Pool Fire Experiment in Tomakomai in 1998. Crude Oil Full Scale Pool Fire Experiment in Tomakomai in 1998. ...

380

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Evaluation of Fire Models for Nuclear Power Plant Applications: Cable Tray Fires. ... ASME Journal of Solar Energy Engineering, Special Issue: Solar ...

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... oxygen consumption. Energy Balance in a Large Compartment Fire. Fire Safety Journal, Vol. 43, No. 3, 180-188, April 2008. ...

382

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Notarianni, KA; McGrattan, KB; Comparison of Fire Sprinkler Piping Materials: Steel ... Chapter 4; Section 5; NFPA HFPE-02;SFPE Handbook of Fire ...

383

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... disasters; fire safety; fire investigations; terrorists; terrorism ... collected to document the event and as ... include first-person interviews conducted as part ...

384

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... plant operators and the NRC to use fire modeling and fire risk information, along with prescriptive requirements, to ensure that nuclear power plants ...

385

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Use of Fire Models in Risk Analysis for Nuclear Power Plants. ... Project to Evaluate Fire Models for Nuclear Power Plant Applications: Summary of 5th ...

386

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... rate; ignition; liquid spills; nuclear power plants; pool fires; small scale fire tests; trash; wood Abstract: A major risk to a nuclear power plant is the ...

387

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Blevins, LG; Investigation of Oil and Gas Well Fires ... KB; Bouldin, C. Simulation of Oil Tank Fires ... Baum, HR; Rehm, RG; Smoke Production From Large ...

388

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... well as relevant reviewed manufacturer information. ... on the post-collision vehicle fire problem ... previous suppression research in vehicles, recent fire ...

389

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Investigation of Oil and Gas Well Fires and Flares. Final Report. Investigation of Oil and Gas Well Fires and Flares. Final Report. ...

390

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Concurrent Flame Spread in Fires: State of the ... of the Waldbaum Fire, Brooklyn, New York, August 3 ... Width Produced by Ejected Propane Gas Fuel ...

391

Gregorian optical system with non-linear optical technology for protection against intense optical transients  

SciTech Connect

An optical system comprising a concave primary mirror reflects light through an intermediate focus to a secondary mirror. The secondary mirror re-focuses the image to a final image plane. Optical limiter material is placed near the intermediate focus to optically limit the intensity of light so that downstream components of the optical system are protected from intense optical transients. Additional lenses before and/or after the intermediate focus correct optical aberrations.

Ackermann, Mark R. (Albuquerque, NM); Diels, Jean-Claude M. (Albuquerque, NM)

2007-06-26T23:59:59.000Z

392

A protection system for the JET ITER-like wall based on imaging diagnostics  

SciTech Connect

The new JET ITER-like wall (made of beryllium and tungsten) is more fragile than the former carbon fiber composite wall and requires active protection to prevent excessive heat loads on the plasma facing components (PFC). Analog CCD cameras operating in the near infrared wavelength are used to measure surface temperature of the PFCs. Region of interest (ROI) analysis is performed in real time and the maximum temperature measured in each ROI is sent to the vessel thermal map. The protection of the ITER-like wall system started in October 2011 and has already successfully led to a safe landing of the plasma when hot spots were observed on the Be main chamber PFCs. Divertor protection is more of a challenge due to dust deposits that often generate false hot spots. In this contribution we describe the camera, data capture and real time processing systems. We discuss the calibration strategy for the temperature measurements with cross validation with thermal IR cameras and bi-color pyrometers. Most importantly, we demonstrate that a protection system based on CCD cameras can work and show examples of hot spot detections that stop the plasma pulse. The limits of such a design and the associated constraints on the operations are also presented.

Arnoux, G.; Balboa, I.; Balshaw, N.; Beldishevski, M.; Cramp, S.; Felton, R.; Goodyear, A.; Horton, A.; Kinna, D.; McCullen, P.; Obrejan, K.; Patel, K.; Lomas, P. J.; Rimini, F.; Stamp, M.; Stephen, A.; Thomas, P. D.; Williams, J.; Wilson, J.; Zastrow, K.-D. [Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); and others

2012-10-15T23:59:59.000Z

393

Investigation of Ground-Fault Protection Devices for Photovoltaic Power Systems Applications  

Science Conference Proceedings (OSTI)

Photovoltaic (PV) power systems, like other electrical systems, may be subject to unexpected ground faults. Installed PV systems always have invisible elements other than those indicated by their electrical schematics. Stray inductance, capacitance and resistance are distributed throughout the system. Leakage currents associated with the PV modules, the interconnected array, wires, surge protection devices and conduit add up and can become large enough to look like a ground-fault. PV systems are frequently connected to other sources of power or energy storage such as batteries, standby generators, and the utility grid. This complex arrangement of distributed power and energy sources, distributed impedance and proximity to other sources of power requires sensing of ground faults and proper reaction by the ground-fault protection devices. The different dc grounding requirements (country to country) often add more confusion to the situation. This paper discusses the ground-fault issues associated with both the dc and ac side of PV systems and presents test results and operational impacts of backfeeding commercially available ac ground-fault protection devices under various modes of operation. Further, the measured effects of backfeeding the tripped ground-fault devices for periods of time comparable to anti-islanding allowances for utility interconnection of PV inverters in the United States are reported.

BOWER,WARD I.; WILES,JOHN

2000-10-03T23:59:59.000Z

394

River Protection Project Integrated safety management system phase II verification review plan - 7/29/99  

Science Conference Proceedings (OSTI)

The purpose of this review is to verify the implementation status of the Integrated Safety Management System (ISMS) for the River Protection Project (RPP) facilities managed by Fluor Daniel Hanford, Inc. (FDH) and operated by Lockheed Martin Hanford Company (LMHC). This review will also ascertain whether within RPP facilities and operations the work planning and execution processes are in place and functioning to effectively protect the health and safety of the workers, public, environment, and federal property over the RPP life cycle. The RPP ISMS should support the Hanford Strategic Plan (DOERL-96-92) to safely clean up and manage the site's legacy waste and deploy science and technology while incorporating the ISMS central theme to ''Do work safely'' and protect human health and the environment.

SHOOP, D.S.

1999-09-10T23:59:59.000Z

395

EPRI/NRC-RES Fire Human Reliability Analysis Guidelines  

Science Conference Proceedings (OSTI)

In 2001, EPRI and Nuclear Regulatory Research (RES) collaborated to improve the state of the art in fire risk assessment to support the new risk-informed environment in fire protection. This project produced a consensus documentNUREG/CR-6850 (EPRI report 1011989), Fire PRA Methodology for Nuclear Power Facilitieswhich addresses fire risk during operations at power plants. NUREG/CR-6850 developed high-level guidance on identifying and including human failure events (HFEs) into the fire PRA (FPRA) and a me...

2009-11-30T23:59:59.000Z

396

Coal-fired high performance power generating system. Quarterly progress report, October 1--December 31, 1992  

SciTech Connect

Our team has outlined a research plan based on an optimized analysis of a 250 MWe combined cycle system applicable to both frame type and aeroderivative gas turbines. Under the constraints of the cycle analysis we have designed a high temperature advanced furnace (FUTAF) which integrates several combustor and air heater designs with appropriate ash management procedures. The Cycle Optimization effort under Task 2 outlines the evolution of our designs. The basic combined cycle approach now includes exhaust gas recirculation to quench the flue gas before it enters the convective air heater. By selecting the quench gas from a downstream location it will be clean enough and cool enough (ca. 300F) to be driven by a commercially available fan and still minimize the volume of the convective air heater. Further modeling studies on the long axial flame, under Task 3, have demonstrated that this configuration is capable of providing the necessary energy flux to the radiant air panels. This flame with its controlled mixing constrains the combustion to take place in a fuel rich environment, thus minimizing the NO{sub x} production. Recent calculations indicate that the NO{sub x} produced is low enough that the SNCR section can further reduce it to within the DOE goal of 0. 15 lbs/MBTU of fuel input. Also under Task 3 the air heater design optimization continued.

1992-12-31T23:59:59.000Z

397

Stone Fire  

NLE Websites -- All DOE Office Websites (Extended Search)

Effect of Change in Cookstove Types on Visibility - Case Study of the Berkeley-Darfur Stove and Three- Stone Fire Extended Abstract #1 Yungang Wang, Ashok J. Gadgil, Thomas W. Kirchstetter Environmental Energy Technologies Division Indoor Environment Group Lawrence Berkeley National Laboratory Berkeley, CA September 2012 This publication was made possible by grant number 500-99-013 from the California Energy Commission (CEC). This work was also supported by the Assistant Secretary for Energy Efficiency and Renewable Energy, Building Technologies Program of the U.S. Department of Energy under contract DE- AC02- 05CH11231. LBNL-6291E LBNL-6291E Disclaimer This document was prepared as an account of work sponsored by the United States

398

Engineering development of advanced coal-fired low-emission boiler systems. Quarterly technical progress report No. 17, October 1, 1996--December 31, 1996  

SciTech Connect

This report describes the work performed between October 1 and December 31, 1996 by the ABB team on U.S. Department of Energy project ``Engineering Development of Advanced Coal-Fired Low-Emission Boiler Systems`` (LEBS), which is part of the DOE`s Combustion 2000 Program. The overall objective of the LEBS Project is to dramatically improve environmental performance of future coal-fired power plants without adversely impacting efficiency or the cost of electricity. Near-term technologies, i.e., advanced technologies that are partially developed, will be used to reduce NO{sub x} and SO{sub 2} emission to one-sixth current NSPS limits and particulates to one- third current NSPS limits.

Regan, J.W.; Bender, D.J.; Clark, J.P.; Wesnor, J.D.

1997-01-01T23:59:59.000Z

399

GAO-04-354, CRITICAL INFRASTRUCTURE PROTECTION: Challenges and Efforts to Secure Control Systems  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Report to Congressional Requesters Report to Congressional Requesters United States General Accounting Office GAO March 2004 CRITICAL INFRASTRUCTURE PROTECTION Challenges and Efforts to Secure Control Systems GAO-04-354 www.gao.gov/cgi-bin/getrpt?GAO-04-354. To view the full product, including the scope and methodology, click on the link above. For more information, contact Robert F. Dacey at (202) 512-3317 or daceyr@gao.gov. Highlights of GAO-04-354, a report to congressional requesters March 2004 CRITICAL INFRASTRUCTURE PROTECTION Challenges and Efforts to Secure Control Systems In addition to general cyber threats, which have been steadily increasing, several factors have contributed to the escalation of the risks of cyber attacks against control systems. These include the adoption of standardized

400

Differential privacy under fire  

Science Conference Proceedings (OSTI)

Anonymizing private data before release is not enough to reliably protect privacy, as Netflix and AOL have learned to their cost. Recent research on differential privacy opens a way to obtain robust, provable privacy guarantees, and systems like PINQ ...

Andreas Haeberlen; Benjamin C. Pierce; Arjun Narayan

2011-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Keywords: smoke plumes; computer programs; crude oil; field models; fire tests; pattern recognition; wind velocity Abstract: ...

402

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Sponsor: National Oceanic and Atmospheric Admin., Washington, DC Keywords: well fires; crude oil; smoke Abstract: This ...

403

Fire, Smoke, and Simulations  

Science Conference Proceedings (OSTI)

... NIST Technologies Help Improve Homeland Security. AVI file (Smokeview simulation animation). Initial Model for Fires in ...

2010-10-05T23:59:59.000Z

404

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Environmental Cycling of Cellulosic Thermal Insulation and Its Influence on Fire Performance. Environmental Cycling of ...

405

Capacitive discharge firing system for providing acoustic sources in the hot dry rock geothermal energy development project  

DOE Green Energy (OSTI)

The development of a capacitive discharge firing unit designed to initiate electrically exploded foil slapper detonators in a subsurface, high-pressure (5000 psi), high-temperature (> 200/sup 0/C) environment is described. The unit is used to conduct acoustic ranging experiments in deep boreholes (approx. = 10,000 ft) in the Los Alamos Scientific Laboratory Geothermal Hot Dry Rock experiment.

Patterson, W.W.; Deam, D.R.; MacDonald, H.J.; Rochester, R.H.

1979-07-01T23:59:59.000Z

406

Consol Energy Summary Report: Evaluation of Mercury Emissions from Coal-Fired Facilities With SCR and FGD Systems  

Science Conference Proceedings (OSTI)

This project was a joint effort between EPRI, the U.S. Department of Energy, Consol Energy, and a number of electric utility companies who hosted the mercury field measurements. This report summarizes mercury measurements by the Consol Energy to characterize the impact of selective catalytic reduction (SCR) on mercury speciation and removal at ten (10) coal-fired power plants.

2006-09-20T23:59:59.000Z

407

S-Security Protective Force and Systems Services for the Nevada Site  

NLE Websites -- All DOE Office Websites (Extended Search)

S-Security Protective Force and Systems Services for the Nevada Site S-Security Protective Force and Systems Services for the Nevada Site Office Solicitation Number: DE-SOL-0002014 Agency: Department of Energy Office: Federal Locations Location: All DOE Federal Contracting Offices Notice Type: Modification/Amendment Original Posted Date: June 22, 2010 Posted Date: June 13, 2011 Response Date: Jul 13, 2011 5:00 pm Mountain Original Response Date: July 7, 2010 Archiving Policy: Manual Archive Original Archive Date: August 6, 2010 Archive Date: - Original Set Aside: N/A Set Aside: N/A Classification Code: S -- Utilities and housekeeping services NAICS Code: 561 -- Administrative and Support Services/561612 -- Security Guards and Patrol Services Solicitation Number: DE-SOL-0002014 Notice Type:

408

Engineering development of coal-fired high performance power systems, Phase 2 and 3. Quarterly progress report, October 1--December 31, 1995  

SciTech Connect

The goals of the program are to develop a coal-fired high performance power generation system (HIPPS) by the year 2000 that is capable of: >47% thermal efficiency (HHV); NO{sub x}, SO{sub x} and particulates {ge} 10% NSPS; coal {ge} 65% of heat input; all solid wastes benign; and cost of electricity 90% of present plant. The HIPPS generating plant integrates a combustion gas turbine/HRSG combined cycle arrangement with an advanced coal-fired boiler. The unique feature of the HIPPS plant is the partial heating of gas turbine (GT) compressor outlet air using energy released by firing coal in the high temperature advanced furnace (HITAF). The compressed air is additionally heated prior to entering the GT expander section by burning natural gas. Energy available, in the gas turbine exhaust and in the HITAF flue gas are used in a steam cycle to maximize energy production. The HIPPS plant arrangement is thus a combination of existing technologies (gas turbine, heat recovery boilers, conventional steam cycle) and new technologies (the HITAF design especially the heater located in the radiant section). Work reported herein is from Task 1.3, HIPPS Commercial Design and Task 2.2, HITAF Air Heaters.

1995-12-31T23:59:59.000Z

409

Boilers and Fired Systems  

SciTech Connect

This chapter examines how energy is consumed, how energy is wasted, and opportunities for reducing energy consumption and costs in the operation of boilers.

Parker, Steven A.; Scollon, R. B.

2009-07-14T23:59:59.000Z

410

Fire Suppression Systems  

Science Conference Proceedings (OSTI)

... docks and an electrical substation that provided ... pump, located on the ground floor, supplied ... sizes under “normally expected” operating conditions. ...

411

Summary of Diagnostic Evaluation for Submarine Cable Cathodic Protection System Performance: Feasibility Assessment of Technologies  

Science Conference Proceedings (OSTI)

This report summarizes the results of an investigation into the operating characteristics of the New York Power Authority's (NYPA) corrosion protection system on the 345kV self-contained fluid-filled (SCFF) submarine cable across Long Island Sound. While directly applicable to the NYPA circuit, the results provide general information that may be useful to all utilities using submarine cable circuits where corrosion may be an issue, including methods to determine the operating characteristics and efficien...

2001-07-20T23:59:59.000Z

412

Operating experience feedback report -- turbine-generator overspeed protection systems: Commercial power reactors. Volume 11  

SciTech Connect

This report presents the results of the US Nuclear Regulatory Commission`s Office for Analysis and Evaluation of Operational Data (AEOD) review of operating experience of main turbine-generator overspeed and overspeed protection systems. It includes an indepth examination of the turbine overspeed event which occurred on November 9, 1991, at the Salem Unit 2 Nuclear Power Plant. It also provides information concerning actions taken by other utilities and the turbine manufacturers as a result of the Salem overspeed event. AEOD`s study reviewed operating procedures and plant practices. It noted differences between turbine manufacturer designs and recommendations for operations, maintenance, and testing, and also identified significant variations in the manner that individual plants maintain and test their turbine overspeed protection systems. AEOD`s study provides insight into the shortcomings in the design, operation, maintenance, testing, and human factors associated with turbine overspeed protection systems. Operating experience indicates that the frequency of turbine overspeed events is higher than previously thought and that the bases for demonstrating compliance with NRC`s General Design Criterion (GDC) 4, Environmental and dynamic effects design bases, may be nonconservative with respect to the assumed frequency.

Ornstein, H.L.

1995-04-01T23:59:59.000Z

413

Memorandum, Additional Approved Qualification Courses of Fire - September  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Memorandum, Additional Approved Qualification Courses of Fire - Memorandum, Additional Approved Qualification Courses of Fire - September 23, 2011 Memorandum, Additional Approved Qualification Courses of Fire - September 23, 2011 September 23, 2011 Newly developed Security Police Officer/Special Response Team Qualification Courses of Fire In accordance with DOE Order 473.2 Protection Program Operations , Section E , paragraph 2 and Section K, Paragraph 2, members of the Department of Energy (DOE) Firearms Policy Panel, DOE Protective Forces Safety Committee, DOE Trainin Managers Working Group, the National Nuclear Security Administration, and the DOE National Training Center have developed, reviewed and revised the following courses of fire (attached) for inclusion in the Protective Force Firearms Qualification Courses Manual. The courses

414

Upgrade of the Nuclear Material Protection, Control and Accounting System at the VNIIEF Industrial Zone  

Science Conference Proceedings (OSTI)

The Industrial Zone at the Russian Federal Nuclear Center/All-Russian Scientific Research Institute of Experimental Physics (RFNC/VNEEF) consists of ten guarded areas with twenty two material balance areas (A and As). The type of facilities in the Industrial Zone include storage sites, machine shops, research facilities, and training facilities. Modernization of the Material Protection, Control and Accounting (MPC and A) System at the Industrial Zone started in 1997. This paper provides a description of, the methodology/strategy used in the upgrade of the MFC and A system.

Lewis, J.C.; Maltsev, V.; Singh, S.P.

1999-09-20T23:59:59.000Z

415

Steam turbine system installation with protection of piping against seismic loading  

SciTech Connect

A steam turbine system installation is described with protection against seismic loading for piping between parts of the system comprising: at least one steam turbine rigidly mounted on a substantially fixed turbine foundation; an auxiliary part of the turbine system mounted by a selectively yielding mounting system on a substantially fixed auxiliary foundation spaced from the turbine foundation; piping connected between the steam turbine and the auxiliary part for fluid flow therebetween; the mounting system for the auxiliary part comprising means for allowing horizontal movement of the auxiliary part in relation to the auxiliary foundation in response to thermal expansion and contraction of the piping and means for resisting movement of the auxiliary part in relation to the auxiliary foundation due to seismic loading.

Pankowiecki, J.

1986-06-10T23:59:59.000Z

416

Model-based analysis of an arc protection and an emergency cooling system  

E-Print Network (OSTI)

Instrumentation and control (I&C) systems play a crucial role in the operation of nuclear power plants and other safety critical processes. An important change that will be going on in the near future is the replacement of the old analogue I&C systems by new digitalised ones. The programmable digital logic controllers enable more complicated control tasks than the old analogue systems and thus the verification of the control logic designs against safety requirements has become more important. In order to diminish the subjective component of the evaluation, there is a need to develop new formal verification methods. This report summarizes the work done in the MODSAFE 2007 project on two case studies where model checking techniques have been used to study an arc protection system and an emergency cooling system. Model checking tools offer typically a finite state machine based

Janne Valkonen; Ville Pettersson; Kim Björkman; Jan-erik Holmberg; Matti Koskimies; Keijo Heljanko; Ilkka Niemelä

2008-01-01T23:59:59.000Z

417

Approval Memorandum, Additional Qualification Courses of Fire - December  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Approval Memorandum, Additional Qualification Courses of Fire - Approval Memorandum, Additional Qualification Courses of Fire - December 13, 2011 Approval Memorandum, Additional Qualification Courses of Fire - December 13, 2011 December 13, 2011 Request approval of revised courses of fire. As indicated in the background section of the memorandum, subjects: Newly Developed SECURITY Policy Officer/Special Response Team Qualification Courses of Fire, dated October 12,2011, members of the Department of Energy (DOE) Firearms Policy Panel, DOE Training Managers Working Group, the National Nuclear Security Administration, and the DOE National Training Center have devloped , reviewed and revised the following courses of fire (attached) for inclusion in the Protective Force Firearms Qualification Courses Manual. The courses of fire pertain to the incubent Security Police

418

EVALUATION METHODOLOGY FOR PROLIFERATION RESISTANCE AND PHYSICAL PROTECTION OF GENERATION IV NUCLEAR ENERGY SYSTEMS: AN OVERVIEW.  

SciTech Connect

This paper provides an overview of the methodology approach developed by the Generation IV International Forum Expert Group on Proliferation Resistance & Physical Protection for evaluation of Proliferation Resistance and Physical Protection robustness of Generation IV nuclear energy systems options. The methodology considers a set of alternative systems and evaluates their resistance or robustness to a collection of potential threats. For the challenges considered, the response of the system to these challenges is assessed and expressed in terms of outcomes. The challenges to the system are given by the threats posed by potential proliferant States and sub-national adversaries on the nuclear systems. The characteristics of the Generation IV systems, both technical and institutional, are used to evaluate their response to the threats and determine their resistance against the proliferation threats and robustness against sabotage and theft threats. System response encompasses three main elements: (1) System Element Identification. The nuclear energy system is decomposed into smaller elements (subsystems) at a level amenable to further analysis. (2) Target Identification and Categorization. A systematic process is used to identify and select representative targets for different categories of pathways, within each system element, that actors (proliferant States or adversaries) might choose to use or attack. (3) Pathway Identification and Refinement. Pathways are defined as potential sequences of events and actions followed by the proliferant State or adversary to achieve its objectives (proliferation, theft or sabotage). For each target, individual pathway segments are developed through a systematic process, analyzed at a high level, and screened where possible. Segments are connected into full pathways and analyzed in detail. The outcomes of the system response are expressed in terms of PR&PP measures. Measures are high-level characteristics of a pathway that include information important to the evaluation methodology users and to the decisions of a proliferant State or adversary. They are first evaluated for segments and then aggregated for complete pathways. Results are aggregated as appropriate to permit pathway comparisons and system assessment. The paper highlights the current achievements in the development of the Proliferation Resistance and Physical Protection Evaluation Methodology. The way forward is also briefly presented together with some conclusions.

BARI, R.; ET AL.

2006-03-01T23:59:59.000Z

419

Evaluation Methodology For Proliferation Resistance And Physical Protection Of Generation IV Nuclear Energy Systems: An Overview  

SciTech Connect

This paper provides an overview of the methodology approach developed by the Generation IV International Forum Expert Group on Proliferation Resistance & Physical Protection for evaluation of Proliferation Resistance and Physical Protection robustness of Generation IV nuclear energy systems options. The methodology considers a set of alternative systems and evaluates their resistance or robustness to a collection of potential threats. For the challenges considered, the response of the system to these challenges is assessed and expressed in terms of outcomes. The challenges to the system are given by the threats posed by potential proliferant States and sub-national adversaries on the nuclear systems. The characteristics of the Generation IV systems, both technical and institutional, are used to evaluate their response to the threats and determine their resistance against the proliferation threats and robustness against sabotage and theft threats. System response encompasses three main elements: 1.System Element Identification. The nuclear energy system is decomposed into smaller elements (subsystems) at a level amenable to further analysis. 2.Target Identification and Categorization. A systematic process is used to identify and select representative targets for different categories of pathways, within each system element, that actors (proliferant States or adversaries) might choose to use or attack. 3.Pathway Identification and Refinement. Pathways are defined as potential sequences of events and actions followed by the proliferant State or adversary to achieve its objectives (proliferation, theft or sabotage). For each target, individual pathway segments are developed through a systematic process, analyzed at a high level, and screened where possible. Segments are connected into full pathways and analyzed in detail. The outcomes of the system response are expressed in terms of PR&PP measures. Measures are high-level characteristics of a pathway that include information important to the evaluation methodology users and to the decisions of a proliferant State or adversary. They are first evaluated for segments and then aggregated for complete pathways. Results are aggregated as appropriate to permit pathway comparisons and system assessment. The paper highlights the current achievements in the development of the Proliferation Resistance and Physical Protection Evaluation Methodology. The way forward is also briefly presented together with some conclusions.

T. Bjornard; R. Bari; R. Nishimura; P. Peterson; J. Roglans; D. Bley; J. Cazalet; G.G.M. Cojazzi; P. Delaune; M. Golay; G. Rendad; G. Rochau; M. Senzaki; I. Therios; M. Zentner

2006-05-01T23:59:59.000Z

420

Engineering development of advanced coal-fired low-emission boiler systems. Technical progress report No. 11, April 1995--June 1995  

Science Conference Proceedings (OSTI)

The Pittsburgh Energy Technology Center of the U.S. Department of Energy (DOE) has contracted with Combustion Engineering, Inc. (ABB CE) to perform work on the {open_quotes}Engineering Development of Advanced Coal-Fired Low-Emission Boiler Systems{close_quotes} Project and has authorized ABB CE to complete Phase I on a cost-reimbursable basis and Phases II and III on a cost-share basis. The overall objective of the Project is the expedited commercialization of advanced coal-fired low-emission boiler systems. The specified primary objectives are: (1) NO{sub x} emissions not greater than one-third NSPS. (2) SO{sub x} emissions not greater than one-third NSPS. (3) Particulate emissions not greater than one-half NSPS. The specific secondary objectives are: (1) Improved ash disposability and reduced waste generation. (2) Reduced air toxics emissions. (3) Increased generating efficiency. The final deliverables are a design data base that will allow future coal-fired power plants to meet the stated objectives and a preliminary design of a Commercial Generation Unit. The work in Phase I covered a 24-month period and included system analysis, RD&T Plan formulation, component definition, and preliminary Commercial Generating Unit (CGU) design. Phase II will cover a 15-month period and will include preliminary Proof-of-Concept Test Facility (POCTF) design and subsystem testing. Phase III will cover a 9-month period and will produce a revised CGU design and a revised POCTF design, cost estimate and a test plan. Phase IV, the final Phase, will cover a 36-month period and will include POCTF detailed design, construction, testing, and evaluation.

NONE

1995-08-30T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Title III Evaluation Report for the Subsurface Fire Water System and Subsurrface Portion of the Non-Portable Water System  

SciTech Connect

The objective of this evaluation is to provide recommendations to ensure consistency between the technical baseline requirements, baseline design, and the as-constructed SFWS/SNPWS. Recommendations for resolving discrepancies between the as-constructed systems, the technical baseline requirements, and the baseline design are included in this report. Cost and schedule estimates are provided for all recommended modifications. This report does not address items which do not meet current safety or code requirements. These items are identified to the CMO and immediate action is taken to correct the situation. The report does identify safety and code items for which the A/E is recommending improvements. The recommended improvements will exceed the minimum requirements of applicable code and safety guidelines. These recommendations are intended to improve and enhance the operation and maintenance of the facility.

R.E. Flye

1998-09-29T23:59:59.000Z

422

NNSA Celebrates Earth Week: Pantex 'greens' firing range | National...  

National Nuclear Security Administration (NNSA)

way, and created a program that shows how Pantex goes the extra mile to protect the environment. The project to "green" the firing range had two components encompassing both...

423

Status Report on Fire Protective Clothing Attributes  

Science Conference Proceedings (OSTI)

... PV denotes present value. ... risk and wage or between risk and price, economists have ... Material prices do not include any markup to cover overhead ...

2007-10-12T23:59:59.000Z

424

FIRE PROTECTION IN MANNED MISSIONS: CURRENT AND ...  

Science Conference Proceedings (OSTI)

... ORBITING PLATFORM IN LOW EARTH ORBIT ... The CO, PFEs are a unique design; they are fitted with a tube, approximately 40 cm long, with a ...

2011-12-22T23:59:59.000Z

425

Powder Panels for Dry Bay Fire Protection  

Science Conference Proceedings (OSTI)

... powder panel by a rotor blade resulted in ... by one of the vehicle manufacturers for the ... specific requirement is proprietary to the manufacturer, but will ...

2011-10-20T23:59:59.000Z

426

Protection system design for power distribution systems in the presence of distributed generation.  

E-Print Network (OSTI)

??The increasing presence of distributed generation and the steady modernization of power distribution system equipment have presented new opportunities in power distribution system studies. This… (more)

Mao, Yiming

2005-01-01T23:59:59.000Z

427

The System Impact of Air-Conditioner Under-voltage Protection Schemes  

Science Conference Proceedings (OSTI)

This paper presents simulation results of evaluating an under-voltage protection scheme designed to take stalled air-conditioner (a/c) units offline such that the slow voltage recovery phenomena can be solved on areas heavily loaded with a/c motors during summer peak periods. A three feeder test-bed has been first used to quantify the effectiveness of the protection scheme and the sensitivity of the under-voltage relay settings. Then two real system events of the Western US power grid have been studied to evaluate the area impact of the protection scheme proposed by Southern California Edison. The study demonstrates that by taking all or most of the stalled a/c unit offline, the feeder voltage will recover in a few seconds, much quicker than the tens of seconds that the standard thermal relays imbedded in the motors need to trip the units. The drawback of the control scheme is that after the voltage recover, it settled at a higher voltage than before the faults because a large chuck of load has been shed.

Lu, Ning; Yang, Bo; Huang, Zhenyu; Bravo, Richard

2009-03-31T23:59:59.000Z

428

To appeared in "Securing Transportation Systems, Protecting Critical Infrastructures Series (Book)", 2012 On the Rationality and Optimality of Transportation  

E-Print Network (OSTI)

To appeared in "Securing Transportation Systems, Protecting Critical Infrastructures Series (Book)", 2012 On the Rationality and Optimality of Transportation Networks Defense -- a Network Centrality Eng., Ben-Gurion University {puzis,elovici}@bgu.ac.il 3 Transportation Research Institute, Technion

429

Uncertainty and sensitivity analysis of a fire-induced accident scenario involving binary variables and mechanistic codes  

E-Print Network (OSTI)

In response to the transition by the United States Nuclear Regulatory Commission (NRC) to a risk-informed, performance-based fire protection rulemaking standard, Fire Probabilistic Risk Assessment (PRA) methods have been ...

Minton, Mark A. (Mark Aaron)

2010-01-01T23:59:59.000Z

430

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Large Fires: Burning of Oil Spills. Large Fires: Burning of Oil Spills. ... These oil burns in a pan ranged in size from 6 m square to 15 m square. ...

431

Circular Economy Assessment for Coal-fired Power Plants Based on Supper-Efficiency DEA Model  

Science Conference Proceedings (OSTI)

Coal-fired power plants are the main pollution source in most areas of China. The implementation of circular economy in coal-fired power plants is necessary for environmental protection and also an effective way of energy saving and emission reduction. ... Keywords: circular economy assessment, circular economy improvement, coal-fired power plant, super-efficiency data envelopment analysis

Shao-lun Zeng; Hong Hu; Wei Wang

2009-10-01T23:59:59.000Z

432

Effective Personnel Exposure Control in Shortened Refueling Outages: Final Report: Review of Remote Monitoring Systems in Radiation Protection Applications  

Science Conference Proceedings (OSTI)

Remote monitoring technology (RMT) significantly enhances worker protection and reduces worker radiation exposure, particularly during shortened refueling outages. This report provides a brief description of the hardware and features of remote monitoring systems, then focuses on nuclear plant experiences in applying such systems for enhanced radiation protection. It also discusses EPRI's RMT research program and formation of the RMT Working Group to support research in this area. Such information will gr...

2003-12-02T23:59:59.000Z

433

DOE Advanced Protection Project  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Task 3 - Advanced Protection - Evaluate measures - 2009 - Design, model Irvine Smart Grid Demo protection system - 2010 6 Copyright 2010, Southern California Edison Task 1 -...

434

Determination of freeze-protection heat loss from a parabolic trough solar system  

DOE Green Energy (OSTI)

A small-scale experiment was undertaken to determine practical control temperatures for a parabolic trough, pulsed-flow water freeze-protection scheme. Measurements were also taken of heat loss from stagnant water in the absorber tube under freezing ambient conditions. Using the experimental data and data available from the literature, manipulation of long-term weather data provided estimates of annual thermal losses to prevent freezing. In a cold climate such as Denver, Colorado's, which typically has 155 freezing days per year, such losses should be less than 0.7% of the annual energy delivered by an efficient parabolic trough system.

May, E.K.

1983-08-01T23:59:59.000Z

435

Analysis of the Design of an HVAC System in a Public Building  

E-Print Network (OSTI)

Based on an example of the design of air conditioning system for a public building, this paper analyzes the characteristics of similar buildings, and introduces the air conditioning system, ventilating system, and the fire control system. The optimized combination of these three systems is carried out in this building to meet the demand on comfort, energy conservation, and fire control and protection, which can provide a reference for the design of similar buildings.

Wei, P.; Shao, Z.; Chen, H.

2006-01-01T23:59:59.000Z

436

Machine Protection System for the Stepper Motor Actuated SyLMAND Mirrors  

SciTech Connect

SyLMAND, the Synchrotron Laboratory for Micro and Nano Devices at the Canadian Light Source, consists of a dedicated X-ray lithography beamline on a bend magnet port, and process support laboratories in a clean room environment. The beamline includes a double mirror system with flat, chromium-coated silicon mirrors operated at varying grazing angles of incidence (4 mrad to 45 mrad) for spectral adjustment by high energy cut-off. Each mirror can be independently moved by two stepper motors to precisely control the pitch and vertical position. We present in this paper the machine protection system implemented in the double mirror system to allow for safe operation of the two mirrors and to avoid consequences of potential stepper motor malfunction.

Subramanian, V. R.; Dolton, W.; Wells, G.; Hallin, E. [Canadian Light Source, 101 Perimeter Road, Saskatoon, SK S7N 0X4 (Canada); Achenbach, S. [Department of Electrical and Computer Engineering, University of Saskatchewan, 57 Campus Dr., Saskatoon, SK S7N 5A9 (Canada); TRLabs, 111-116 Research Dr., Saskatoon, SK S7N 3R3 (Canada); Karlsruhe Institute of Technology, Postfach 3640, D-76021 Karlsruhe (Germany); Klymyshyn, D. M. [Department of Electrical and Computer Engineering, University of Saskatchewan, 57 Campus Dr., Saskatoon, SK S7N 5A9 (Canada); TRLabs, 111-116 Research Dr., Saskatoon, SK S7N 3R3 (Canada); Augustin, M. [Karlsruhe Institute of Technology, Postfach 3640, D-76021 Karlsruhe (Germany)

2010-06-23T23:59:59.000Z

437

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Keywords: in situ burning; oil spills; fire research; environmental effects; crude oil; numerical models Abstract: A combination ...

438

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... National Technical Information Service Keywords: oil spills; combustion; smoke generation; crude oil; tests; pool fires; energy transfer Abstract: ...

439

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Emergency Response Operations ... Safety Investigation of the World Trade Center Disaster. ... high rise buildings; building collapse; disasters; fire safety ...

440

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... of the World Trade Center Disaster. ... rise buildings; building collapse; disasters; fire safety ... structural analysis; structural damage; structural response ...

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... of the World Trade Center Disaster. ... high rise buildings; building collapse; disasters; fire safety ... structures; thermal response; flameproofing; radiative ...

442

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... to the World Trade Center Disaster. ... World Trade Center; disasters; building collapse ... fires; flameproofing; steels; evacuation; response time; roofs ...

443

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Nuclear Power Plants. NISTIR 6986; 569 p. September 2003.International Collaborative Project to Evaluate Fire Models for Nuclear Power Plant ...

444

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Evacuation Time Components: Lessons from Nuclear Power Plants, Hurricanes, and ... of Selected Fire Models for Nuclear Power Plant Applications. ...

445

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Rate Characteristics of Some Combustible Fuel Sources in Nuclear Power Plants. ... to Evaluate Fire Models for Nuclear Power Plant Applications. ...

446

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... and the Nuclear Regulatory Commission (NRC) are collaborating to assess and validate fire computer codes for nuclear power plant applications. ...

447

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... gas temperature; heat loss; enclosures; nuclear power plants; cables; ventilation ... validate fire computer codes for nuclear power plant applications. ...

448

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Kwon, SW; Liapi, KA; Haas, CT; Sreenivasan, SV; McLaughlin, JT; Human Behavior and Fire Emergencies: An Annotated Bibliography. ...

449

Wind Driven Fires  

Science Conference Proceedings (OSTI)

... fighters working in a single-story residential structure fire. ... Department of Homeland Security Federal Emergency Management Agency Assistance ...

2013-07-16T23:59:59.000Z

450

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... of incomplete combustion, and have been found adsorbed on the particulate emissions from wood fires, pulverized coal combustion, waste ...

451

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Performance on Fires Exposed to an External Energy Source. ... Grosshandler, WL; Nyden, MR; Rinkinen, WJ; Simple Piezoelectric Droplet Generator. ...

452

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... Concentration by Tunable Diode Laser Absorption Spectroscopy ... Next Generation Fire Suppression Technology Program. FY1999 Annual Report. ...

453

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... insulation. Adiabatic Surface Temperature for Calculating Heat Transfer to Fire Exposed Structures. Volume 2;Interflam 2007. (Interflam '07). ...

454

Building and Fire Publications  

Science Conference Proceedings (OSTI)

... high rise buildings; building collapse; disasters; fire ... adhesive strength; building codes; cohesive ... materials; thermal conductivity; thermal insulation ...

455

Wildland Fires Texas 2011  

Science Conference Proceedings (OSTI)

Wildland-Urban Interface Fires, Amarillo, Texas 2011. ... The deployment was conducted jointly with the Texas Forest Service (TFS). ...

2012-12-11T23:59:59.000Z

456

Engineering development of advanced coal-fired low-emission boiler systems. Technical progress report No. 12, July--September 1995  

SciTech Connect

The overall objective of the Project is the expedited commercialization of advanced coal-fired low-emission boiler systems. The goals for emissions and plant efficiency are: NO{sub x} emissions not greater than 0.1 lb/million Btu; SO{sub x} emissions not greater than 0.1 lb/million Btu; particulate emissions not greater than 0.01 lb/million Btu; and net plant efficiency (HHV basis) not less than 42%. Other goals include: improved ash disposability and reduced waste generation; and reduced air toxics emissions. The final deliverables are a design data base that will allow future coal-fired power plants to meet the stated objectives, and a preliminary design of a Commercial Generation Unit. The work in Phase I covered a 24- month period and included system analysis, RD&T Plan formulation, component definition, and preliminary Commercial Generating Unit (CGU) design. Phase II will cover a 15-month period and will include preliminary Proof-of-Concept Test Facility (POCTF) design and subsystem testing. Phase III will cover a 9-month period and will produce a revised CGU design and a revised POCTF design, cost estimate and a test plan. Phase IV, the final Phase, will cover a 36- month period and will include POCTF detailed design, construction, testing, and evaluation.

NONE

1995-11-27T23:59:59.000Z

457

Voxels on Fire  

Science Conference Proceedings (OSTI)

We introduce a method for the animation of fire propagation and the burning consumption of objects represented as volumetric data sets. Our method uses a volumetric fire propagation model based on an enhanced distance field. It can simulate the spreading ... Keywords: Fire Propagation, Distance Field, Lattice Boltzmann Model, Splatting, GPU Acceleration

Ye Zhao; Xiaoming Wei; Zhe Fan; Arie Kaufman; Hong Qin

2003-10-01T23:59:59.000Z

458

Fire Department Emergency Response  

SciTech Connect

In 1995 the SRS Fire Department published the initial Operations Basis Document (OBD). This document was one of the first of its kind in the DOE complex and was widely distributed and reviewed. This plan described a multi-mission Fire Department which provided fire, emergency medical, hazardous material spill, and technical rescue services.

Blanchard, A. [Westinghouse Savannah River Company, AIKEN, SC (United States); Bell, K.; Kelly, J.; Hudson, J.

1997-09-01T23:59:59.000Z

459

Optimizing Fire Station Locations for the Istanbul Metropolitan Municipality  

Science Conference Proceedings (OSTI)

The Istanbul Metropolitan Municipality IMM seeks to determine locations for additional fire stations to build in Istanbul; its objective is to make residences and historic sites reachable by emergency vehicles within five minutes of a fire station’s ... Keywords: fire station location, geographic information system, maximal-covering problem, set-covering problem

Emel Akta?; Özay Özayd?n; Burçin Bozkaya; Füsun Ülengin; ?ule Önsel

2013-05-01T23:59:59.000Z

460

Wildland Fire Management Plan for Brookhaven National Laboratory  

SciTech Connect

This Wildland Fire Management Plan (FMP) for Brookhaven National Lab (BNL) updates the 2003 plan incorporating changes necessary to comply with DOE Order 450.1 and DOE P 450.4, Federal Wildland Fire Management Policy and Program Review; Wildland and Prescribed Fire Management Policy and implementation Procedures Reference Guide. This current plan incorporates changes since the original draft of the FMP that result from new policies on the national level. This update also removes references and dependence on the U.S. Fish & Wildlife Service and Department of the Interior, fully transitioning Wildland Fire Management responsibilities to BNL. The Department of Energy policy for managing wildland fires requires that all areas, managed by the DOE and/or its various contractors, that can sustain fire must have a FMP that details fire management guidelines for operational procedures associated with wild fire, operational, and prescribed fires. Fire management plans provide guidance on fire preparedness, fire prevention, wildfire suppression, and the use of controlled, 'prescribed' fires and mechanical means to control the amount of available combustible material. Values reflected in the BNL Wildland FMP include protecting life and public safety; Lab properties, structures and improvements; cultural and historical sites; neighboring private and public properties; and endangered, threatened, and species of concern. Other values supported by the plan include the enhancement of fire-dependent ecosystems at BNL. This FMP will be reviewed periodically to ensure the fire program advances and evolves with the missions of the DOE and BNL. This Fire Management Plan is presented in a format that coverers all aspects specified by DOE guidance documents which are based on the national template for fire management plans adopted under the National Fire Plan. The DOE is one of the signatory agencies on the National Fire Plan. This FMP is to be used and implemented for the entire BNL site including the Upton Reserve and has been reviewed by, The Nature Conservancy, New York State Department of Environmental Conservation Forest Rangers, and DOE, as well as appropriate BNL emergency services personnel. The BNL Fire Department is the lead on wildfire suppression. However, the BNL Natural Resource Manager will be assigned to all wildland fires as technical resource advisor.

Green,T.

2009-10-23T23:59:59.000Z

Note: This page contains sample records for the topic "fire protection systems" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Wildland Fire Management Plan for Brookhaven National Laboratory  

SciTech Connect

This Wildland Fire Management Plan (FMP) for Brookhaven National Lab (BNL) updates the 2003 plan incorporating changes necessary to comply with DOE Order 450.1 and DOE P 450.4, Federal Wildland Fire Management Policy and Program Review; Wildland and Prescribed Fire Management Policy and implementation Procedures Reference Guide. This current plan incorporates changes since t