Powered by Deep Web Technologies
Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Measurements and Predictions of the Heat Transfer at the Tube-Fin Junction for Louvered Fin Heat Exchangers  

E-Print Network [OSTI]

Measurements and Predictions of the Heat Transfer at the Tube-Fin Junction for Louvered Fin Heat Transfer at the Tube-Fin Junction for Louvered Fin Heat Exchangers Abstract The dominant thermal resistance used to increase heat transfer by initiating new boundary layer growth and increasing surface area

Thole, Karen A.

2

Finned Tube With Vortex Generators For A Heat Exchanger.  

DOE Patents [OSTI]

A system for and method of manufacturing a finned tube for a heat exchanger is disclosed herein. A continuous fin strip is provided with at least one pair of vortex generators. A tube is rotated and linearly displaced while the continuous fin strip with vortex generators is spirally wrapped around the tube.

Sohal, Monohar S. (Idaho Falls, ID); O'Brien, James E. (Idaho Falls, ID)

2004-09-14T23:59:59.000Z

3

Experimental and numerical investigation on air-side performance of fin-and-tube heat exchangers with various fin patterns  

SciTech Connect (OSTI)

Air-side heat transfer and friction characteristics of five kinds of fin-and-tube heat exchangers, with the number of tube rows (N = 12) and the diameter of tubes (D{sub o} = 18 mm), have been experimentally investigated. The test samples consist of five types of fin configurations: crimped spiral fin, plain fin, slit fin, fin with delta-wing longitudinal vortex generators (VGs) and mixed fin with front 6-row vortex-generator fin and rear 6-row slit fin. The heat transfer and friction factor correlations for different types of heat exchangers were obtained with the Reynolds numbers ranging from 4000 to 10000. It was found that crimped spiral fin provides higher heat transfer and pressure drop than the other four fins. The air-side performance of heat exchangers with the above five fins has been evaluated under three sets of criteria and it was shown that the heat exchanger with mixed fin (front vortex-generator fin and rear slit fin) has better performance than that with fin with delta-wing vortex generators, and the slit fin offers best heat transfer performance at high Reynolds numbers. Based on the correlations of numerical data, Genetic Algorithm optimization was carried out, and the optimization results indicated that the increase of VG attack angle or length, or decrease of VG height may enhance the performance of vortex-generator fin. The heat transfer performances for optimized vortex-generator fin and slit fin at hand have been compared with numerical method. (author)

Tang, L.H.; Zeng, M.; Wang, Q.W. [State Key Laboratory of Multiphase Flow in Power Engineering, Xi'an Jiaotong University, Xi'an, Shaanxi 710049 (China)

2009-07-15T23:59:59.000Z

4

Boiling heat transfer in a hydrofoil-based micro pin fin heat sink  

E-Print Network [OSTI]

Boiling heat transfer in a hydrofoil-based micro pin fin heat sink Ali KosÃ?ar, Yoav Peles-based micro pin fin heat sink was investigated. Average two-phase heat transfer coefficients were obtained intermittent and spray-annular flows. Heat transfer coefficient trends and flow morphologies were used to infer

Peles, Yoav

5

Fouling of HVAC fin and tube heat exchangers  

SciTech Connect (OSTI)

Fin and tube heat exchangers are used widely in residential, commercial and industrial HVAC applications. Invariably, indoor and outdoor air contaminants foul these heat exchangers. This fouling can cause decreased capacity and efficiency of the HVAC equipment as well as indoor air quality problems related to microbiological growth. This paper describes laboratory studies to investigate the mechanisms that cause fouling. The laboratory experiments involve subjecting a 4.7 fins/cm (12 fins/inch) fin and tube heat exchanger to an air stream that contains monodisperse particles. Air velocities ranging from 1.5-5.2 m/s (295 ft/min-1024 ft/min) and particle sizes from 1--8.6 {micro}m are used. The measured fraction of particles that deposit as well as information about the location of the deposited material indicate that particles greater than about 1 {micro}m contribute to fouling. These experimental results are used to validate a scaling analysis that describes the relative importance of several deposition mechanisms including impaction, Brownian diffusion, turbophoresis, thermophoresis, diffusiophoresis, and gravitational settling. The analysis is extended to apply to different fin spacings and particle sizes typical of those found in indoor air.

Siegel, Jeffrey; Carey, Van P.

2001-07-01T23:59:59.000Z

6

3D numerical simulation on fluid flow and heat transfer characteristics in multistage heat exchanger with slit fins  

Science Journals Connector (OSTI)

In this paper, a numerical investigation is performed for three-stage heat exchangers with plain plate fins and slit ... are arranged in a staggered way, and heat conduction in fins is considered. In order ... av...

W. Q. Tao; Y. P. Cheng; T. S. Lee

2007-11-01T23:59:59.000Z

7

Effects of winglets to augment tube wall heat transfer in louvered fin heat exchangers  

E-Print Network [OSTI]

Effects of winglets to augment tube wall heat transfer in louvered fin heat exchangers Paul A transfer along the tube wall of the compact heat exchanger through the use of winglets placed of attack, aspect ratio, direction, and shape, were all evaluated based on heat transfer augmentation

Thole, Karen A.

8

Conjugate heat transfer in channels with internal longitudinal corrugated fins  

E-Print Network [OSTI]

@~ and @?, i' or Various K; F = 0. 020 and L = 0. 215 . 3. 10 Local Surface Temperature versus B, ~ and Q? for ql and q2 Boundary Conditions; F = 0. 020 and L = 0. 215 3. 11 Local Surface Heat Flux versus +~ and Rq~ for Various 6; F = 0. 02 3. 12 Local... axis length of the channel. Ar ? Flow cross-sectional area in the calculation domain. Ay~ ? Flow cross-sectional area in the calculation domain when there is no fin. c ? Specific heat of the flowing fluid, D ? Height of the flow cross section. Ds...

Ackermann, J. Albert

2012-06-07T23:59:59.000Z

9

An experimental investigation of heat transfer in narrow, rectangular cooling channels with pin-fins  

E-Print Network [OSTI]

][Ro]/[Ro] = 0.12). Heat transfer in a stationary pin-fin channel can be enhanced up to 3.8 times that of a smooth channel. Rotation enhances the heat transferred from the pin-fin channels 1.5 times that of the stationary pin-fin channels. Overall, rotation...

Wright, Lesley Mae

2012-06-07T23:59:59.000Z

10

Error Analysis of Heat Transfer for Finned-Tube Heat-Exchanger Text-Board  

E-Print Network [OSTI]

In order to reduce the measurement error of heat transfer in water and air side for finned-tube heat-exchanger as little as possible, and design a heat-exchanger test-board measurement system economically, based on the principle of test-board system...

Chen, Y.; Zhang, J.

2006-01-01T23:59:59.000Z

11

Plate Fin Heat Exchanger Model with Axial Conduction and Variable Properties  

SciTech Connect (OSTI)

Future superconducting radio frequency (SRF) cavities, as part of Project X at Fermilab, will be cooled to superfluid helium temperatures by a cryogenic distribution system supplying cold supercritical helium. To reduce vapor fraction during the final Joule-Thomson (J-T) expansion into the superfluid helium cooling bath, counter-flow, plate-fin heat exchangers will be utilized. Due to their compact size and ease of fabrication, plate-fin heat exchangers are an effective option. However, the design of compact and high-effectiveness cryogenic heat exchangers operating at liquid helium temperatures requires consideration of axial heat conduction along the direction of flow, in addition to variable fluid properties. Here we present a numerical model that includes the effects of axial conduction and variable properties for a plate fin heat exchanger. The model is used to guide design decisions on heat exchanger material choice and geometry. In addition, the J-T expansion process is modeled with the heat exchanger to analyze the effect of heat load and cryogenic supply parameters. A numerical model that includes the effects of axial conduction and variable properties for a plate fin heat exchanger was developed and the effect of various design parameters on overall heat exchanger size was investigated. It was found that highly conductive metals should be avoided in the design of compact JT heat exchangers. For the geometry considered, the optimal conductivity is around 3.5 W/m-K and can range from 0.3-10 W/m-K without a large loss in performance. The model was implemented with an isenthalpic expansion process. Increasing the cold side inlet temperature from 2K to 2.2 K decreased the liquid fraction from 0.856 to 0.839 which corresponds to a 0.12 g/s increase in supercritical helium supply needed to maintain liquid level in the cooling bath. Lastly, it was found that the effectiveness increased when the heat load was below the design value. Therefore, the heat exchanger should be sized on the high end of the required heat load.

Hansen, B.J.; White, M.J.; Klebaner, A.; /Fermilab

2011-06-10T23:59:59.000Z

12

Scaling of Heat Transfer Coefficients Along Louvered Fins A. C. Lyman1  

E-Print Network [OSTI]

1 Scaling of Heat Transfer Coefficients Along Louvered Fins A. C. Lyman1 , R. A. Stephan2 , and K 23681-2199 #12;2 Abstract Louvered fins provide a method for improving the heat transfer performance for evaluating the spatially-resolved louver heat transfer coefficients using various reference temperatures

Thole, Karen A.

13

Heat transfer from multiple row arrays of low aspect ratio pin fins Seth A. Lawson a,  

E-Print Network [OSTI]

Heat transfer from multiple row arrays of low aspect ratio pin fins Seth A. Lawson a, , Alan A 18 March 2011 Available online 5 May 2011 Keywords: Pin fins Heat transfer augmentation Array to enhance heat transfer. In modern gas turbines, for exam- ple, airfoils are designed with sophisticated

Thole, Karen A.

14

Local Heat Transfer for Finned-Tube Heat Exchangers using Oval Tubes  

SciTech Connect (OSTI)

This paper presents the results of an experimental study of forced convection heat transfer in a narrow rectangular duct fitted with either a circular tube or an elliptical tube in crossflow. The duct was designed to simulate a single passage in a fin-tube heat exchanger. Heat transfer measurements were obtained using a transient technique in which a heated airflow is suddenly introduced to the test section. High-resolution local fin-surface temperature distributions were obtained at several times after initiation of the transient using an imaging infrared camera. Corresponding local fin-surface heat transfer coefficient distributions were then calculated from a locally applied one-dimensional semi-infinite inverse heat conduction model. Heat transfer results were obtained over an airflow rate ranging from 1.56 x 10-3 to 15.6 x 10-3 kg/s. These flow rates correspond to a duct-height Reynolds number range of 630 – 6300 with a duct height of 1.106 cm and a duct width-toheight ratio, W/H, of 11.25. The test cylinder was sized such that the diameter-to-duct height ratio, D/H is 5. The elliptical tube had an aspect ratio of 3:1 and a/H equal to 4.33. Results presented in this paper reveal visual and quantitative details of local fin-surface heat transfer distributions in the vicinity of circular and oval tubes and their relationship to the complex horseshoe vortex system that forms in the flow stagnation region. Fin surface stagnation-region Nusselt numbers are shown to be proportional to the square-root of Reynolds number.

O'Brien, James Edward; Sohal, Manohar Singh

2000-08-01T23:59:59.000Z

15

Heat Transfer Enhancement for Finned-tube Heat Exchangers with Winglets  

SciTech Connect (OSTI)

This paper presents the results of an experimental study of forced convection heat transfer in a narrow rectangular duct fitted with a circular tube and/or a delta-winglet pair. The duct was designed to simulate a single passage in a fin-tube heat exchanger. Heat transfer measurements were obtained using a transient technique in which a heated airflow is suddenly introduced to the test section. High-resolution local fin-surface temperature distributions were obtained at several times after initiation of the transient using an imaging infrared camera. Corresponding local fin-surface heat transfer coefficient distributions were then calculated from a locally applied one-dimensional semi-infinite inverse heat conduction model. Heat transfer results were obtained over an airflow rate ranging from 1.51 x 10-3 to 14.0 x 10-3 kg/s. These flow rates correspond to a duct-height Reynolds number range of 670 – 6300 with a duct height of 1.106 cm and a duct width-toheight ratio, W/H, of 11.25. The test cylinder was sized such that the diameter-to-duct height ratio, D/H is 5. Results presented in this paper reveal visual and quantitative details of local fin-surface heat transfer distributions in the vicinity of a circular tube, a delta-winglet pair, and a combination of a circular tube and a delta-winglet pair. Comparisons of local and average heat transfer distributions for the circular tube with and without winglets are provided. Overall mean finsurface Nusselt-number results indicate a significant level of heat transfer enhancement associated with the deployment of the winglets with the circular cylinder. At the lowest Reynolds numbers (which correspond to the laminar operating conditions of existing geothermal air-cooled condensers), the enhancement level is nearly a factor of two. At higher Reynolds numbers, the enhancement level is close to 50%.

O'Brien, James Edward; Sohal, Manohar Singh

2000-11-01T23:59:59.000Z

16

Heat Transfer Enhancement for Finned-Tube Heat Exchangers with Vortex Generators: Experimental and Numerical Results  

SciTech Connect (OSTI)

A combined experimental and numerical investigation is under way to investigate heat transfer enhancement techniques that may be applicable to large-scale air-cooled condensers such as those used in geothermal power applications. The research is focused on whether air-side heat transfer can be improved through the use of finsurface vortex generators (winglets,) while maintaining low heat exchanger pressure drop. A transient heat transfer visualization and measurement technique has been employed in order to obtain detailed distributions of local heat transfer coefficients on model fin surfaces. Pressure drop measurements have also been acquired in a separate multiple-tube row apparatus. In addition, numerical modeling techniques have been developed to allow prediction of local and average heat transfer for these low-Reynolds-number flows with and without winglets. Representative experimental and numerical results presented in this paper reveal quantitative details of local fin-surface heat transfer in the vicinity of a circular tube with a single delta winglet pair downstream of the cylinder. The winglets were triangular (delta) with a 1:2 height/length aspect ratio and a height equal to 90% of the channel height. Overall mean fin-surface Nusselt-number results indicate a significant level of heat transfer enhancement (average enhancement ratio 35%) associated with the deployment of the winglets with oval tubes. Pressure drop measurements have also been obtained for a variety of tube and winglet configurations using a single-channel flow apparatus that includes four tube rows in a staggered array. Comparisons of heat transfer and pressure drop results for the elliptical tube versus a circular tube with and without winglets are provided. Heat transfer and pressure-drop results have been obtained for flow Reynolds numbers based on channel height and mean flow velocity ranging from 700 to 6500.

O'Brien, James Edward; Sohal, Manohar Singh; Huff, George Albert

2002-08-01T23:59:59.000Z

17

3D Numerical heat transfer and fluid flow analysis in plate-fin and tube heat exchangers with electrohydrodynamic enhancement  

Science Journals Connector (OSTI)

Three-dimensional laminar fluid flow and heat transfer over a four-row plate-fin and tube heat exchanger with electrohydrodynamic (EHD) wire electrodes...V E...=0–16 kV) are investigated in detail...

Chia-Wen Lin; Jiin-Yuh Jang

2005-05-01T23:59:59.000Z

18

Heat transfer enhancement from micro pin fins subjected to an impinging jet , Hee Joon Lee 1  

E-Print Network [OSTI]

fins fabricated using MEMS microfab- rication. The micro pin fins had diameters of 125 lm, heights of 230 lm, and pitches of 250 lm with an area enhancement of Atotal/Abase = 2.44. The jet stand-off ratio such as electronics cooling and turbine blade cooling. It has been also used for drying applications, metal

Peles, Yoav

19

Heat transfer augmentation along the tube wall of a louvered fin heat exchanger using practical delta winglets  

E-Print Network [OSTI]

Heat transfer augmentation along the tube wall of a louvered fin heat exchanger using practical the formation of streamwise vortices and increase heat transfer between a working fluid and the surface on which the winglets are placed. This study investigates the use of delta winglets to augment heat transfer on the tube

Thole, Karen A.

20

Determination of heat transfer and friction characteristics of an adapted inclined louvered fin  

SciTech Connect (OSTI)

An experimental study of a fin-and-tube heat exchanger was performed. To this end a test rig was constructed to measure the heat transfer rate on the air and waterside of the heat exchanger. A wide range of Reynolds numbers on the airside was investigated. The resulting data was used to determine the convective heat transfer correlation (expressed using the Colburn factor) and the friction factor on the airside. The fin type used in the heat exchanger of this research is an adaptation of the standard inclined louvered type. A thorough error analysis was performed, to validate the results. (author)

T'Joen, C.; Steeman, H.-J.; Willockx, A.; De Paepe, M. [Department of Flow, Heat and Combustion Mechanics, Ghent University-UGent, Sint-Pietersnieuwstraat 41, 9000 Gent (Belgium)

2006-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Experimental investigation of plastic finned-tube heat exchangers, with emphasis on material thermal conductivity  

SciTech Connect (OSTI)

In this paper, two modified types of polypropylene (PP) with high thermal conductivity up to 2.3 W/m K and 16.5 W/m K are used to manufacture the finned-tube heat exchangers, which are prospected to be used in liquid desiccant air conditioning, heat recovery, water source heat pump, sea water desalination, etc. A third plastic heat exchanger is also manufactured with ordinary PP for validation and comparison. Experiments are carried out to determine the thermal performance of the plastic heat exchangers. It is found that the plastic finned-tube heat exchanger with thermal conductivity of 16.5 W/m K can achieve overall heat transfer coefficient of 34 W/m{sup 2} K. The experimental results are compared with calculation and they agree well with each other. Finally, the effect of material thermal conductivity on heat exchanger thermal performance is studied in detail. The results show that there is a threshold value of material thermal conductivity. Below this value improving thermal conductivity can considerably improve the heat exchanger performance while over this value improving thermal conductivity contributes very little to performance enhancement. For the finned-tube heat exchanger designed in this paper, when the plastic thermal conductivity can reach over 15 W/m K, it can achieve more than 95% of the titanium heat exchanger performance and 84% of the aluminum or copper heat exchanger performance with the same dimension. (author)

Chen, Lin; Li, Zhen; Guo, Zeng-Yuan [Department of Engineering Mechanics, Key Laboratory for Thermal Science and Power Engineering of Ministry of Education, Tsinghua University, Beijing 100084 (China)

2009-07-15T23:59:59.000Z

22

Study of junction flows in louvered fin round tube heat exchangers using the dye injection technique  

SciTech Connect (OSTI)

Detailed studies of junction flows in heat exchangers with an interrupted fin design are rare. However, understanding these flow structures is important for design and optimization purposes, because the thermal hydraulic performance of heat exchangers is strongly related to the flow behaviour. In this study flow visualization experiments were performed in six scaled-up models of a louvered fin round tube heat exchanger. The models have three tube rows in a staggered layout and differ only in their fin spacing and louver angle. A water tunnel was designed and built and the flow visualizations were carried out using dye injection. At low Reynolds numbers the streakline follows the tube contours, while at higher Reynolds numbers a horseshoe vortex is developed ahead of the tubes. The two resulting streamwise vortex legs are destroyed by the downstream louvers (i.e. downstream the turnaround louver), especially at higher Reynolds numbers, smaller fin pitches and larger louver angles. Increasing the fin spacing results in a larger and stronger horseshoe vortex. This illustrates that a reduction of the fin spacing results in a dissipation of vortical motion by mechanical blockage and skin friction. Furthermore it was observed that the vortex strength and number of vortices in the second tube row is larger than in the first tube row. This is due to the thicker boundary layer in the second tube row, and the flow deflection, which is typical for louvered fin heat exchangers. Visualizations at the tube-louver junction showed that in the transition part between the angled louver and the flat landing a vortex is present underneath the louver surface which propagates towards the angled louver. (author)

Huisseune, H.; Willockx, A.; De Paepe, M. [Department of Flow, Heat and Combustion Mechanics, Ghent University, Sint-Pietersnieuwstraat 41, 9000 Gent (Belgium); T'Joen, C. [Department of Flow, Heat and Combustion Mechanics, Ghent University, Sint-Pietersnieuwstraat 41, 9000 Gent (Belgium); Department Radiation, Radionuclides and Reactors, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands); De Jaeger, P. [Department of Flow, Heat and Combustion Mechanics, Ghent University, Sint-Pietersnieuwstraat 41, 9000 Gent (Belgium); NV Bekaert SA, Bekaertstraat 2, 8550 Zwevegem (Belgium)

2010-11-15T23:59:59.000Z

23

Heat transfer and pressure drop correlations for the rectangular offset strip fin compact heat exchanger  

Science Journals Connector (OSTI)

The development of thermal-hydraulic design tools for rectangular offset strip fin compact heat exchangers and the associated convection process are delineated. On the basis of current understanding of the physical phenomena and enhancement mechanisms, existing empirical f and j data for actual cores are reanalyzed. The asymptotic behavior of the data in the deep laminar and fully turbulent flow regimes is identified. The respective asymptotes for f and j are shown to be correlated by power law expressions in terms of Re and the dimensionless geometric parameters ?, ?, and ?. Finally, rational design equations for f and j are presented in the form of single continuous expressions covering the laminar, transition, and turbulent flow regimes.

Raj M. Manglik; Arthur E. Bergles

1995-01-01T23:59:59.000Z

24

Thermal behavior of spiral fin-and-tube heat exchanger having fly ash deposit  

SciTech Connect (OSTI)

This research investigates the effect of fly-ash deposit on thermal performance of a cross-flow heat exchanger having a set of spiral finned-tubes as a heat transfer surface. A stream of warm air having high content of fly-ash is exchanging heat with a cool water stream in the tubes. In this study, the temperature of the heat exchanger surface is lower than the dew point temperature of air, thus there is condensation of moisture in the air stream on the heat exchanger surface. The affecting parameters such as the fin spacing, the air mass flow rate, the fly-ash mass flow rate and the inlet temperature of warm air are varied while the volume flow rate and the inlet temperature of the cold water stream are kept constant at 10 l/min and 5 C, respectively. From the experiment, it is found that as the testing period is shorter than 8 h the thermal resistance due to the fouling increases with time. Moreover, the deposit of fly-ash on the heat transfer surface is directly proportional to the dust-air ratio and the amount of condensate on heat exchange surface. However, the deposit of fly-ash is inversely proportional to the fin spacing. The empirical model for evaluating the thermal resistance is also developed in this work and the simulated results agree well with those of the measured data. (author)

Nuntaphan, Atipoang [Thermal Technology Research Laboratory, Mae Moh Training Center, Electricity Generating Authority of Thailand, Mae Moh, Lampang 52220 (Thailand); Kiatsiriroat, Tanongkiat [Department of Mechanical Engineering, Chiang Mai University, Chiang Mai 50200 (Thailand)

2007-08-15T23:59:59.000Z

25

Experimental investigation of highly effective plate-fin heat exchanger surfaces  

Science Journals Connector (OSTI)

Results are presented of an experimental investigation of a new convective rational heat transfer augmentation law in plate-fin heat exchanger surfaces. This law is characterized by Nu/Nusm ? ?/?sm by comparing channels (heat transfer surfaces) with vortex promoters with similar smooth channels at equal Reynolds numbers. For experimental confirmation and investigation of this law, heat exchanger cores having three different plate-fin surfaces were developed and manufactured. Two surfaces are formed by short offset channels (interrupted surfaces) of equilateral triangular and rectangular cross sections. The third surface has channels of isosceles triangular cross sections, with transverse projections and grooves along the channel length direction. The experimental results and correlations are reported for the three surfaces. The experiments were conducted in a wind tunnel with specially developed precise instrumentation that ensured experimental uncertainties of ?? = ± 2.3% and ?Re = 1.7% at a 0.997 confidence level. Analysis of the results indicated that the fundamental character and causes limiting rational heat transfer augmentation to Nu/Nusm ? ?/?sm depend upon the heat transfer surface configuration. This paper consolidates the author's research on the subject reported in the Russian language over the last 25 years.

E.V. Dubrovsky

1995-01-01T23:59:59.000Z

26

Determination of the Number of Tube Rows to Obtain Closure for Volume Averaging Theory Based Model of Fin-and-Tube Heat Exchangers  

E-Print Network [OSTI]

Fig. 3 Journal of Heat Transfer Grid system for 2-row caseDomain and Grid System. Since the fin-and- tube heat

Zhou, Feng; Hansen, Nicholas E; Geb, David J; Catton, Ivan

2011-01-01T23:59:59.000Z

27

Metal-Organic Heat Carrier Nanofluids. | EMSL  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Organic Heat Carrier Nanofluids. Metal-Organic Heat Carrier Nanofluids. Abstract: Nanofluids, dispersions of metal or oxide nanoparticles in a base working fluid, are being...

28

Thermal management optimization of an air-cooled Li-ion battery module using pin-fin heat sinks for hybrid electric vehicles  

Science Journals Connector (OSTI)

Abstract Three dimensional transient thermal analysis of an air-cooled module that contains prismatic Li-ion cells next to a special kind of aluminum pin fin heat sink whose heights of pin fins increase linearly through the width of the channel in air flow direction was studied for thermal management of Lithium-ion battery pack. The effects of pin fins arrangements, discharge rates, inlet air flow velocities, and inlet air temperatures on the battery were investigated. The results showed that despite of heat sinks with uniform pin fin heights that increase the standard deviation of the temperature field, using this kind of pin fin heat sink compare to the heat sink without pin fins not only decreases the bulk temperature inside the battery, but also decreases the standard deviation of the temperature field inside the battery as well. Increasing the inlet air temperature leads to decreasing the standard deviation of the temperature field while increases the maximum temperature of the battery. Furthermore, increasing the inlet air velocity first increases the standard deviation of the temperature field till reaches to the maximum point, and after that decreases. Also, increasing the inlet air velocity leads to decrease in the maximum temperature of the battery.

Shahabeddin K. Mohammadian; Yuwen Zhang

2015-01-01T23:59:59.000Z

29

Volume Averaging Theory (VAT) based modeling and closure evaluation for fin-and-tube heat exchangers  

E-Print Network [OSTI]

made to simulate the heat transfer and fluid flow across theanalysis of heat transfer and fluid flow in a three-lent flow and heat transfer in a porous layer. J Fluids Eng

Zhou, Feng; Catton, Ivan

2012-01-01T23:59:59.000Z

30

Numerical Evaluation of Flow and Heat Transfer in Plate-Pin Fin Heat Sinks with Various Pin Cross-Sections  

E-Print Network [OSTI]

Liu, Research on the Heat Transfer and Flow Performance of aCompound Heat Sink, Numer. Heat Transfer A, vol. 55, no. 5,Hand- book of Numerical Heat Transfer, 2nd ed. , chap. 6,

Zhou, Feng; Catton, Ivan

2011-01-01T23:59:59.000Z

31

Heat transfer and fluid flow characteristics of microchannels with internal longitudinal fins.  

E-Print Network [OSTI]

??Electronic components generate large amount of heat during their operation, which requires to be dissipated. Over the past decade, internal heat generation levels have exponentially… (more)

Foong, Andrew Jun Li

2009-01-01T23:59:59.000Z

32

Fluctuating local thermoelectric heat in dirty metals  

SciTech Connect (OSTI)

Using a recently developed multilead theory of dephasing in mesoscopic conductors, the mean-squared magnitude of the local Peltier heat in a uniform disordered metal is calculated diagrammatically. A heuristic estimate based on conductance fluctuation theory is also developed, and gives the same results. The generation and absorption of local thermoelectric heats require both phase-coherent elastic scattering to produce local conductance fluctuations and phase-breaking inelastic scattering to transport heat to and from the reservoirs. This phenomenon can cause substantial spatial variations in the electron temperature of low-carrier-density, clean, quasi-two-dimensional metals.

DiVincenzo, D.P. (IBM Research Division, Thomas J. Watson Research Center, Yorktown Heights, New York 10598 (United States))

1993-07-15T23:59:59.000Z

33

Fouling of HVAC Fin and Tube Heat Exchangers Jeffrey Siegel and Van P. Carey  

E-Print Network [OSTI]

Fouling of heat exchangers used in heating, ventilating, and air conditioning (HVAC) systems is important contributor to overall energy use and peak electric demand. Furthermore, the location of heat exchangers in HVAC systems means that if bioaerosols containing bacteria, fungi, and viruses deposit on heat

34

Numerical Evaluation of Flow and Heat Transfer in Plate-Pin Fin Heat Sinks with Various Pin Cross-Sections  

E-Print Network [OSTI]

in Table 3. The grid systems for all heat sink models areregion. The grid system for one of the heat sinks is shown

Zhou, Feng; Catton, Ivan

2011-01-01T23:59:59.000Z

35

OPTIMIZATION OF INTERNAL HEAT EXCHANGERS FOR HYDROGEN STORAGE TANKS UTILIZING METAL HYDRIDES  

SciTech Connect (OSTI)

Two detailed, unit-cell models, a transverse fin design and a longitudinal fin design, of a combined hydride bed and heat exchanger are developed in COMSOL{reg_sign} Multiphysics incorporating and accounting for heat transfer and reaction kinetic limitations. MatLab{reg_sign} scripts for autonomous model generation are developed and incorporated into (1) a grid-based and (2) a systematic optimization routine based on the Nelder-Mead downhill simplex method to determine the geometrical parameters that lead to the optimal structure for each fin design that maximizes the hydrogen stored within the hydride. The optimal designs for both the transverse and longitudinal fin designs point toward closely-spaced, small cooling fluid tubes. Under the hydrogen feed conditions studied (50 bar), a 25 times improvement or better in the hydrogen storage kinetics will be required to simultaneously meet the Department of Energy technical targets for gravimetric capacity and fill time. These models and methodology can be rapidly applied to other hydrogen storage materials, such as other metal hydrides or to cryoadsorbents, in future work.

Garrison, S.; Tamburello, D.; Hardy, B.; Anton, D.; Gorbounov, M.; Cognale, C.; van Hassel, B.; Mosher, D.

2011-07-14T23:59:59.000Z

36

Neutron imaging of alkali metal heat pipes  

SciTech Connect (OSTI)

High-temperature heat pipes are two-phase, capillary driven heat transfer devices capable of passively providing high thermal fluxes. Such a device using a liquid-metal coolant can be used as a solution for successful thermal management on hypersonic flight vehicles. Imaging of the liquid-metal coolant inside will provide valuable information in characterizing the detailed heat and mass transport. Neutron imaging possesses an inherent advantage from the fact that neutrons penetrate the heat pipe metal walls with very little attenuation, but are significantly attenuated by the liquid metal contained inside. Using the BT-2 beam line at the National Institute of Standards and Technology (NIST) in Gaithersburg, Maryland, preliminary efforts have been conducted on a nickel-sodium heat pipe. The contrast between the attenuated beam and the background is calculated to be approximately 3%. This low contrast requires sacrifice in spatial or temporal resolution so efforts have since been concentrated on lithium (Li) which has a substantially larger neutron attenuation cross section. Using the CG-1D beam line at the High Flux Isotope Reactor (HFIR) of Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee, the first neutron images of high-temperature molybdenum (Mo)-Li heat pipes have been achieved. The relatively high neutron cross section of Li allows for the visualization of the Li working fluid inside the heat pipes. The evaporator region of a gravity assisted cylindrical heat pipe prototype 25 cm long was imaged from start-up to steady state operation up to approximately 900 C. In each corner of the square bore inside, the capillary action raises the Li meniscus above the bulk Li pool in the evaporator region. As the operational temperature changes, the meniscus shapes and the bulk meniscus height also changes. Furthermore, a three-dimensional tomographic image is also reconstructed from the total of 128 projection images taken 1.4o apart in which the Li had already cooled and solidified.

Kihm, Ken [University of Tennessee, Knoxville (UTK); Kirchoff, Eric [University of Tennessee, Knoxville (UTK); Golden, Matt [University of Tennessee, Knoxville (UTK); Rosenfeld, J. [Thermacore Inc.; Rawal, S. [Lockheed Martin Space Systems Company; Pratt, D. [United States Air Force Research Laboratory, Wright-Patterson Air Force Base; Bilheux, Hassina Z [ORNL; Walker, Lakeisha MH [ORNL; Voisin, Sophie [ORNL; Hussey, Dan [NIST Center for Neutron Research (NCRN), Gaithersburg, MD

2013-01-01T23:59:59.000Z

37

Experimental and Numerical Investigation of Pool Boiling Heat Transfer on Engineered Nano-Finned Surfaces  

E-Print Network [OSTI]

angle was measured both before and after the experiments. Nucleate pool boiling heat transfer was enhanced with increase in pillar height. Numerical predictions for R_(k) obtained from Molecular Dynamics (MD) simulations were found to be consistent...

Yang, Hongjoo

2014-08-10T23:59:59.000Z

38

Optimization of the Fin Heat Pipe for Ventilating and Air Conditioning with a Genetic Algorithm  

E-Print Network [OSTI]

conservation, and it is urgent. At the same time, the energy consumption about air-conditioning of buildings continues to increase and the new wind energy accounts for 4%~12% of the buildings total energy consumption [1]. A heat recovery system for air...

Qian, J.; Sun, D.; Li, G.

2006-01-01T23:59:59.000Z

39

Metal-Organic Heat Carrier Nanofluids  

SciTech Connect (OSTI)

Nanofluids, dispersions of metal or oxide nanoparticles in a base working fluid, are being intensively studied due to improvements they offer in thermal properties of the working fluid. However, these benefits have been erratically demonstrated and proven impacts on thermal conductivity are modest and well described from long-established effective medium theory. In this paper, we describe a new class of metal-organic heat carrier (MOHC) nanofluid that offers potential for a larger performance boost in thermal vapor-liquid compression cycles. MOHCs are nanophase porous coordination solids designed to reversibly uptake the working fluid molecules in which the MOHCs are suspended. Additional heat can be extracted in a heat exchanger or solar collector from the endothermic enthalpy of desorption, which is then released as the nanofluid transits through a power generating device such as a turboexpander. Calculations for an R123 MOHC nanofluid indicated potential for up to 15% increase in power output. Capillary tube experiments show that liquid-vapor transitions occur without nanoparticle deposition on the tube walls provided entrance Reynolds number exceeds approximately 100.

McGrail, B. Peter; Thallapally, Praveen K.; Blanchard, Jeremy; Nune, Satish K.; Jenks, Jeromy WJ; Dang, Liem X.

2013-09-01T23:59:59.000Z

40

Heat dissipating nuclear reactor with metal liner  

DOE Patents [OSTI]

Disclosed is a nuclear reactor containment including a reactor vessel disposed within a cavity with capability for complete inherent decay heat removal in the earth and surrounded by a cast steel containment member which surrounds the vessel. The member has a thick basemat in contact with metal pilings. The basemat rests on a bed of porous particulate material, into which water is fed to produce steam which is vented to the atmosphere. There is a gap between the reactor vessel and the steel containment member. The containment member holds any sodium or core debris escaping from the reactor vessel if the core melts and breaches the vessel.

Gluekler, Emil L. (San Jose, CA); Hunsbedt, Anstein (Los Gatos, CA); Lazarus, Jonathan D. (Sunnyvale, CA)

1987-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Flow visualisation in inclined louvered fins  

SciTech Connect (OSTI)

In this study the flow within an interrupted fin design, the inclined louvered fin, is investigated experimentally through visualisation. The inclined louvered fin is a hybrid of the offset strip fin and standard louvered fin, aimed at improved performance at low Reynolds numbers for compact heat exchangers. The flow behaviour is studied in six geometrically different configurations over a range of Reynolds numbers and quantified using the concept of 'fin angle alignment factor'. The transition from steady laminar to unsteady flow was studied in detail. The fin geometry had a very large impact on the transitional flow behaviour, especially on vortex shedding. (author)

T'Joen, C.; De Paepe, M. [Department of Flow, Heat and Combustion Mechanics, Ghent University-UGent, Sint-Pietersnieuwstraat 41, 9000 Gent (Belgium); Jacobi, A. [Department of Mechanical Science and Engineering, University of Illinois at Urbana-Champaign, 1206 West Green Street, Urbana, IL 61801 (United States)

2009-04-15T23:59:59.000Z

42

Heat Transfer by Free Convection in a Liquid Metal  

Science Journals Connector (OSTI)

19 December 1961 research-article Heat Transfer by Free Convection in a Liquid Metal F. J. Bayley...an experimental investigation of the free convection heat transfer process under the special conditions associated with...

1961-01-01T23:59:59.000Z

43

Metal Dusting of Heat-Resistant Alloys  

E-Print Network [OSTI]

Metal dusting leads to disintegration of such alloys as iron and nickel-based into a “dust” of particulate metal, metal carbide, carbon, and/or oxide. It occurs in strongly carburising environments at 400-900°C. Literature survey has shown...

Al-Meshari, Abdulaziz I

44

Project Profile: High Operating Temperature Liquid Metal Heat...  

Broader source: Energy.gov (indexed) [DOE]

investigating the use of metal alloys as a heat transfer fluid (HTF) in concentrating solar power (CSP) systems operating at temperatures in excess of 800C. By allowing higher...

45

Computationally Optimized Homogenization Heat Treatment of Metal Alloys  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Computationally Optimized Homogenization Heat Computationally Optimized Homogenization Heat Treatment of Metal Alloys Contact NETL Technology Transfer Group techtransfer@netl.doe.gov May 2013 Significance * Reduction in energy consumption and carbon dioxide output due to shorter, more effective heat treatments * Substantially lower processing costs * Ability to optimize the mechanical properties of alloys for improved downstream performance * Adaptable to the constraints of individual production facilities and the level of homogenization desired Applications * Any solid substitutional alloy utilized in a

46

Experimental Analysis of the Single-Phase Heat Transfer and Friction Factor inside the Horizontal Internally Micro-Fin Tube  

E-Print Network [OSTI]

and shell-side condensers to increase heat transfer. This enables water chillers to reach high efficiency, it was observed that the buoyancy effect is present in the laminar region. The efficiency index (the ratio of tube is widely used in high flow rate applications because the heat transfer enhancement in high flow

Ghajar, Afshin J.

47

Relationship between heat transfer intensity and absolute vorticity flux intensity in flat tube bank fin channels with Vortex Generators  

Science Journals Connector (OSTI)

The heat transfer enhancement can be achieved through the secondary flow. It is found that absolute vorticity flux along the main flow can describe the secondary flow intensity and correspond to the heat transfer enhancement averaged in span wise direction. Investigations to verify this phenomenon are reported. The results show that there has a similar distribution for absolute vorticity flux in the main flow direction compared with that for span averaged Nusselt number. The conformance of Nusselt number and absolute vorticity flux shows that absolute vorticity flux can reflect the intensity of heat transfer produced by the secondary flow.

Ke-Wei Song; Liang-Bi Wang

2008-01-01T23:59:59.000Z

48

Natural Convection Heat Transfer in a Rectangular Liquid Metal Pool With Bottom Heating and Top Cooling  

SciTech Connect (OSTI)

An experimental study is performed to investigate the natural convection heat transfer characteristics with subcooled coolant to create engineering database for basic applications in a lead alloy cooled reactor. Tests are performed in the ALTOS (Applied Liquid-metal Thermal Operation Study) apparatus as part of MITHOS (Metal Integrated Thermo Hydrodynamic Operation System). A relationship is determined between the Nusselt number Nu and the Rayleigh number Ra in the liquid metal rectangular pool. Results are compared with correlations and experimental data in the literature. Given the similar Ra condition, the present test results for Nu of the liquid metal pool with top subcooling are found to be similar to those predicted by the existing correlations or experiments. The current test results are utilized to develop natural convection heat transfer correlations applicable to low Prandtl number Pr fluids that are heated from below and cooled by the external coolant above. Results from this study are slated to be used in designing BORIS (Battery Optimized Reactor Integral System), a small lead cooled modular fast reactor for deployment at remote sites cycled with MOBIS (Modular Optimized Brayton Integral System) for electricity generation, tied with NAVIS (Naval Application Vessel Integral System) for ship propulsion, joined with THAIS (Thermochemical Hydrogen Acquisition Integral System) for hydrogen production, and coupled with DORIS (Desalination Optimized Reactor Integral System) for seawater desalination. Tests are performed with Wood's metal (Pb-Bi-Sn-Cd) filling a rectangular pool whose lower surface is heated and upper surface cooled by forced convection of water. The test section is 20 cm long, 11.3 cm high and 15 cm wide. The simulant has a melting temperature of 78 deg. C. The constant temperature and heat flux condition was realized for the bottom heating once the steady state had been met. The test parameters include the heated bottom surface temperature of the liquid metal pool, the input power to the bottom surface of the section, and the coolant temperature. (authors)

Lee, Il S.; Yu, Yong H.; Son, Hyoung M.; Hwang, Jin S.; Suh, Kune Y. [Seoul National University, 599 Gwanangno, Gwanak-gu, Seoul, 151-742 (Korea, Republic of)

2006-07-01T23:59:59.000Z

49

An experimental study of endwall heat transfer enhancement for flow past staggered non-conducting pin fin arrays  

E-Print Network [OSTI]

: : : : : : : : : : : : : : : : : : : : : : : : 15 VI RESULTS AND DISCUSSION : : : : : : : : : : : : : : : : : : : 17 A. Effect of Reynolds Number ReDh . . . . . . . . . . . . . . 17 B. Effect of Height of Pins, H=D . . . . . . . . . . . . . . . . 21 C. Effect of Stream Wise Spacing of Pins, SL=D... Pressure Drop for D = 2:54cm : 23 9 Effect of H=D on Thermal Performance for D = 2:54cm : : : : : : : 24 10 Effect of SL=D on Heat Transfer Enhancement for D=1.27cm : : : : 25 11 Effect of SL=D on Increase of Overall Pressure Drop for D = 1:27cm 26 12...

Achanta, Vamsee Satish

2004-09-30T23:59:59.000Z

50

An Investigation and Characterization of Metal Foam Filled Double-Pipe Heat Exchangers.  

E-Print Network [OSTI]

??The effect of using metal foams in double-pipe heat exchangers is investigated in this work. The advantages and drawbacks of using metal foams in these… (more)

Chen, Xi

2014-01-01T23:59:59.000Z

51

Radiant heating tests of several liquid metal heat-pipe sandwich panels  

SciTech Connect (OSTI)

Integral heat pipe sandwich panels, which synergistically combine the thermal efficiency of heat pipes and the structural efficiency of honeycomb sandwich construction, were conceived as a means of alleviating thermal stress problems in the Langley Scramjet Engine. Test panels which utilized two different wickable honeycomb cores, facesheets with screen mesh sintered to the internal surfaces, and a liquid metal working fluid (either sodium or potassium) were tested by radiant heating at various heat load levels. The heat pipe panels reduced maximum temperature differences by 31 percent with sodium working fluid and 45 percent with potassium working fluid. Results indicate that a heat pipe sandwich panel is a potential, simple solution to the engine thermal stress problem. Other interesting applications of the concept include: cold plates for electronic component and circuit card cooling, radiators for large space platforms, low distortion large area structures (e.g., space antennas) and laser mirrors.

Camarda, C.J.; Basiulis, A.

1983-08-01T23:59:59.000Z

52

Reduction of Metal Oxides by Microwave Heating of Multi-walled...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Reduction of Metal Oxides by Microwave Heating of Multi-walled Carbon Nanotubes Microwave heating of a metal oxide in the presence of multi-walled carbon nanotubes may result in...

53

High Operating Temperature Liquid Metal Heat Transfer Fluids  

Broader source: Energy.gov [DOE]

This fact sheet describes a UCLA-led solar project to investigate high operating temperature liquid metal heat transfer fluids, funded by the SunShot initiative. The project team is using a combination of modeling along with a variety of property measurement and validation studies to demonstrate that the metal alloys identified can meet all the needs of a concentrating solar power plant. A successful candidate fluid would allow for the reduction of the levelized cost of energy by increasing the operating temperature for the CSP plant power cycle, which would increase thermal-to-electric conversion efficiency.

54

High Operating Temperature Liquid Metal Heat Transfer Fluids  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Liquid Metal Liquid Metal Heat Transfer Fluids UCLA, UCB, Yale DE-EE0005941 | April 15, 2013 | Ju 1.1 Thermochemistry modeling * Continue CALPHAD based calculations to search for optimal ternary alloy compositions. * Initiate development of liquid density models. 1.2 Combinatorial synthesis and characterization * Pipe-Liquid interaction of compositional library * More alloys, alloy additions and effect on liquidus temperatures * Iteratively optimize the compositions. 1.3 Corrosion characterization and mitigation * Tune static corrosion testing systems for testing over an extended period of time. * Perform analysis of the micro mechanical testing on the oxide layers. 1.4 Heat transfer characterization and modeling * Complete the construction of the flow loop and perform experiments to measure

55

Project Profile: High Operating Temperature Liquid Metal Heat Transfer Fluids  

Broader source: Energy.gov [DOE]

The University of California, Los Angeles (UCLA), along with partners at the University of California, Berkeley, and Yale University, under the 2012 Multidisciplinary University Research Initiative (MURI): High Operating Temperature (HOT) Fluids funding opportunity, is investigating the use of metal alloys as a heat transfer fluid (HTF) in concentrating solar power (CSP) systems operating at temperatures in excess of 800°C. By allowing higher temperature operation, CSP systems can achieve greater efficiencies and thereby reduce the overall cost of electricity production.

56

SunShot Initiative: High Operating Temperature Liquid Metal Heat Transfer  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

High Operating Temperature Liquid High Operating Temperature Liquid Metal Heat Transfer Fluids to someone by E-mail Share SunShot Initiative: High Operating Temperature Liquid Metal Heat Transfer Fluids on Facebook Tweet about SunShot Initiative: High Operating Temperature Liquid Metal Heat Transfer Fluids on Twitter Bookmark SunShot Initiative: High Operating Temperature Liquid Metal Heat Transfer Fluids on Google Bookmark SunShot Initiative: High Operating Temperature Liquid Metal Heat Transfer Fluids on Delicious Rank SunShot Initiative: High Operating Temperature Liquid Metal Heat Transfer Fluids on Digg Find More places to share SunShot Initiative: High Operating Temperature Liquid Metal Heat Transfer Fluids on AddThis.com... Concentrating Solar Power Systems Components Competitive Awards

57

Transient Thermal, Hydraulic, and Mechanical Analysis of a Counter Flow Offset Strip Fin Intermediate Heat Exchanger using an Effective Porous Media Approach  

E-Print Network [OSTI]

Computational Fluid Mechanics and Heat Transfer. New York,the two fluids and enhance heat transfer between them. Most1]. This EPM fluid dynamics and heat transfer computational

Urquiza, Eugenio

2009-01-01T23:59:59.000Z

58

Pacific Power - FinAnswer Express | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Pacific Power - FinAnswer Express Pacific Power - FinAnswer Express Pacific Power - FinAnswer Express < Back Eligibility Agricultural Commercial Fed. Government Industrial Institutional Local Government Nonprofit State Government Savings Category Other Home Weatherization Commercial Weatherization Heating & Cooling Cooling Commercial Heating & Cooling Appliances & Electronics Construction Design & Remodeling Manufacturing Heat Pumps Heating Commercial Lighting Lighting Insulation Water Heating Windows, Doors, & Skylights Maximum Rebate General: 70% of energy efficiency project cost If incentive brings the simple payback below one year, the incentive is reduced so the simple payback equals one year. Program Info State California Program Type Utility Rebate Program Rebate Amount T-8 Lighting Fixtures: $3-$7

59

Pacific Power - FinAnswer Express | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Pacific Power - FinAnswer Express Pacific Power - FinAnswer Express Pacific Power - FinAnswer Express < Back Eligibility Agricultural Commercial Construction Industrial Institutional Local Government Nonprofit State Government Savings Category Other Home Weatherization Commercial Weatherization Heating & Cooling Cooling Commercial Heating & Cooling Appliances & Electronics Construction Design & Remodeling Manufacturing Heat Pumps Heating Commercial Lighting Lighting Water Heating Windows, Doors, & Skylights Maximum Rebate Lighting: 70% of cost Incentive amount cannot reduce the project simple payback below one year Program Info State District of Columbia Program Type Utility Rebate Program Rebate Amount Lighting T-8 Lighting Fixtures: $0.25-$21 T-5 Lighting Fixtures: $0.25-$20 Cold Cathode: $5

60

Project Profile: Thermochemical Heat Storage for CSP Based on Multivalent Metal Oxides  

Broader source: Energy.gov [DOE]

General Atomics (GA), under the Thermal Storage FOA, is developing a high-density thermochemical heat storage system based on solid metal oxides.

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Nanoscale Heat Conduction across Metal-Dielectric Interfaces  

E-Print Network [OSTI]

resistance between a metal and a dielectric material assumedresistance of a metallic film bounded by dielectric materials.resistance of a metallic film bounded by dielectric materials.

Ju, Y. Sungtaek

2005-01-01T23:59:59.000Z

62

Determination of the Number of Tube Rows to Obtain Closure for Volume Averaging Theory Based Model of Fin-and-Tube Heat Exchangers  

E-Print Network [OSTI]

out f ¼ Fig. 4 Fluid flow and heat transfer over a backwardtaking the fluid flow and heat transfer over a backward1980, Numerical Heat Transfer and Fluid Flow, Hemisphere

Zhou, Feng; Hansen, Nicholas E; Geb, David J; Catton, Ivan

2011-01-01T23:59:59.000Z

63

Liquid Metal Heat Exchanger for Geologic Deposits - Energy Innovation...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

heating apparatus that efficiently heats subterranean geological deposits, such as oil shale, to extract hydrocarbons for energy needs. The apparatus provides more efficient...

64

Rocky Mountain Power - FinAnswer Express | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Rocky Mountain Power - FinAnswer Express Rocky Mountain Power - FinAnswer Express Rocky Mountain Power - FinAnswer Express < Back Eligibility Agricultural Commercial Construction Industrial Savings Category Other Home Weatherization Commercial Weatherization Heating & Cooling Commercial Heating & Cooling Cooling Manufacturing Heat Pumps Appliances & Electronics Commercial Lighting Lighting Insulation Design & Remodeling Windows, Doors, & Skylights Program Info State Idaho Program Type Utility Rebate Program Rebate Amount '''New Construction/Major Renovation Only''' Interior Lighting: $0.08/kwh annual energy savings LED Fixture (Exterior): $100 Induction Fixture (Exterior): $125 CFL Wallpack (Exterior): $30 Lighting Control (Exterior): $70 '''Retrofit Only''' Fluorescent Fixture Upgrades: $5-$20/fixture

65

Joining of parts via magnetic heating of metal aluminum powders  

DOE Patents [OSTI]

A method of joining at least two parts includes steps of dispersing a joining material comprising a multi-phase magnetic metal-aluminum powder at an interface between the at least two parts to be joined and applying an alternating magnetic field (AMF). The AMF has a magnetic field strength and frequency suitable for inducing magnetic hysteresis losses in the metal-aluminum powder and is applied for a period that raises temperature of the metal-aluminum powder to an exothermic transformation temperature. At the exothermic transformation temperature, the metal-aluminum powder melts and resolidifies as a metal aluminide solid having a non-magnetic configuration.

Baker, Ian

2013-05-21T23:59:59.000Z

66

Optimization of functionally graded metallic foam insulation under transient heat transfer conditions  

Science Journals Connector (OSTI)

The problem of minimizing the maximum temperature of a structure insulated by a functionally graded metal foam insulation under transient heat conduction is studied. First, the performance of insulation designed ...

H. Zhu; B.V. Sankar; R.T. Haftka…

2004-11-01T23:59:59.000Z

67

Metal boiling under the action of an electron-beam heat source  

Science Journals Connector (OSTI)

The dynamics of vapor bubble growth in a metal alloy under the action of a volume heat source are considered. The possibility of existence of a threshold superheating value below which the boiling process is i...

G. E. Gorelik; A. S. Lerman; N. V. Pavlyukevich…

1975-10-01T23:59:59.000Z

68

A model for the latent heat of melting in free standing metal nanoparticles  

SciTech Connect (OSTI)

Nanoparticles of many metals are known to exhibit scale dependent latent heats of melting. Analytical models for this phenomenon have so far failed to completely capture the observed phenomena. Here we present a thermodynamic analysis for the melting of metal nanoparticles in terms of their internal energy and a scale dependent surface tension proposed by Tolman. The resulting model predicts the scale dependence of the latent heat of melting and is confirmed using published data for tin and aluminum.

Shin, Jeong-Heon; Deinert, Mark R., E-mail: mdeinert@mail.utexas.edu [Department of Mechanical Engineering, The University of Texas at Austin, Austin, Texas 78715 (United States)

2014-04-28T23:59:59.000Z

69

Metal Hydride Chemical Heat Pumps for Industrial Use  

E-Print Network [OSTI]

Hydriding alloys are intermetallic absorbent compounds which have the remarkable quality of absorbing very large quantities of hydrogen gas per unit volume of metallic powder. The absorption and desorption of hydrogen are exothermic and endothermic...

Ally, M. R.; Rebello, W. J.; Rosso, M. J., Jr.

1984-01-01T23:59:59.000Z

70

Rocky Mountain Power - FinAnswer Express | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Rocky Mountain Power - FinAnswer Express Rocky Mountain Power - FinAnswer Express Rocky Mountain Power - FinAnswer Express < Back Eligibility Agricultural Commercial Construction Industrial Installer/Contractor Savings Category Other Home Weatherization Commercial Weatherization Heating & Cooling Commercial Heating & Cooling Cooling Appliances & Electronics Manufacturing Heat Pumps Commercial Lighting Lighting Insulation Design & Remodeling Water Heating Windows, Doors, & Skylights Maximum Rebate Lighting Retrofit: 70% of project cost Program Info State Wyoming Program Type Utility Rebate Program Rebate Amount Custom: $0.10/annual kWh saved Interior Lighting: $0.08/kwh annual energy savings LED Fixture (Exterior): $100 Induction Fixture (Exterior): $125 Lighting Control (Exterior): $70 Air Conditioners and Heat Pumps: $50-$100/ton

71

Rocky Mountain Power - Energy FinAnswer | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Rocky Mountain Power - Energy FinAnswer Rocky Mountain Power - Energy FinAnswer Rocky Mountain Power - Energy FinAnswer < Back Eligibility Agricultural Commercial Construction Industrial Savings Category Heating & Cooling Home Weatherization Construction Commercial Weatherization Commercial Heating & Cooling Design & Remodeling Other Maximum Rebate Retrofit: 50% of eligible measure cost Lighting Energy Savings Limit: 50%-75% of savings Program Info State Utah Program Type Utility Rebate Program Rebate Amount 0.12/kWh annual energy savings + 50/kW average monthly on-peak demand savings Provider Rocky Mountain Power Rocky Mountain Power's Energy FinAnswer program provides cash incentives to help its commercial and industrial customers improve the efficiency of their existing facilities and build new facilities that are significantly

72

Waste Heat Recovery in the Metal Working Industry  

E-Print Network [OSTI]

recuperators supplying four 3" burners. The smaller (1,500 lb. capacity) forge furnace was not equipped with eductors. No furnace pres sure control was used. This furnace had one 10,000 scfh recuperator supplying two 2~" hot air burners. The heat treat... furnaces were both constant com bustion air, throttled fuel control. The motor ized valve in the fuel line was positioned by a position proportioning temperature controller according to a manually set set point and thermo couple input. Both furnaces...

McMann, F. C.; Thurman, J.

1983-01-01T23:59:59.000Z

73

Liquid Metal as a Heat Transport Fluid for Thermal Solar Power Applications  

Science Journals Connector (OSTI)

Abstract In order to increase the thermal efficiency and produce process heat for hydrogen production, the operating temperature of the heat transfer fluid in thermal solar plants needs to increase. In addition reaching 900 °C would also increase the heat storage density and the efficiency of the thermodynamic cycle by using a combined cycle for electricity production. The benefits of hydrogen (e.g., for fuel cells) and a more efficient thermodynamic cycle would allow a plant to have a higher energy output per square acre of land use, thereby increasing its economic competiveness. Today, solar thermal plants do not operate at these high temperatures due to the fact that conventional heat transport fluids begin to disintegrate around 600 °C [1,2]. For non-solar applications, low melting-temperature metals, such as wood's metal and lead- bismuth eutectic alloy, have been examined as heat-transport media, because of the large temperature ranges over which they remain liquid. Lead-bismuth eutectic alloy (LBE; 45% Pb, 55% Bi) melts at 125 °C and does not boil until 1670 °C, making it an ideal heat-transfer medium for application in thermal solar power [3]. The main obstacle to using LBE is finding structural materials that can withstand the harsh corrosion environments at high temperatures. In this work the key issues of materials exposed to liquid metal are described while initial data on carious steels tested in liquid metal are provided. While corrosion is a significant issue in this environment, mechanical failure of steels in liquid metal are discussed as well.

D. Frazer; E. Stergar; C. Cionea; P. Hosemann

2014-01-01T23:59:59.000Z

74

In-field remediation of tons of heavy metal-rich waste by Joule heating vitrification  

Science Journals Connector (OSTI)

An in-field remediation method of tons of Pb and Zn-rich ceramic waste based on Joule heating vitrification is presented. The progressive heating up to about 1850 °C led to the complete melting of the waste material and the rapid cooling of the melt formed a monolithic glass of 55 tons. The obtained glass was chemically and morphologically homogeneous and immobilized the heavy metals and non-volatile inorganic compounds. The occurrence of crystalline phases such as zircon and cordierite was observed in the lowermost part of the monolith due to the different cooling rate. Leaching tests showed that the vitrified monolith presented a high chemical resistance and metal ions were immobilized into the glass matrix. The presented in-field vitrification process was highly effective in the remediation of tons of heavy metal-rich materials and can be exploited further for remediation of large amounts of soils and asbestos-based materials.

Francesco Dellisanti; Piermaria L. Rossi; Giovanni Valdrè

2009-01-01T23:59:59.000Z

75

Rocky Mountain Power - FinAnswer Express | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Rocky Mountain Power - FinAnswer Express Rocky Mountain Power - FinAnswer Express Rocky Mountain Power - FinAnswer Express < Back Eligibility Agricultural Commercial Construction Industrial Multi-Family Residential Savings Category Other Home Weatherization Commercial Weatherization Heating & Cooling Commercial Heating & Cooling Cooling Heat Pumps Appliances & Electronics Commercial Lighting Lighting Manufacturing Insulation Design & Remodeling Windows, Doors, & Skylights Program Info State Utah Program Type Utility Rebate Program Rebate Amount Interior Lighting: $0.08/kWh annual savings Induction Fixture (Exterior): $125/unit LED Outdoor/Roadway Fixture (Exterior): $100/unit CFL Wall Pack (Exterior): $30/unit Lighting Controls: $75/sensor Wall Insulation: $0.07/sq. ft. Roof Insulation: $0.05/sq. ft.

76

Metal and Glass Manufacturers Reduce Costs by Increasing Energy Efficiency in Process Heating Systems  

Broader source: Energy.gov [DOE]

Process heating plays a key role in producing steel, aluminum, and glass and in manufacturing products made from these materials. Faced with regulatory and competitive pressures to control emissions and reduce operating costs, metal and glass manufacturers are considering a variety of options for reducing overall energy consumption. As 38% of the energy used in U.S. industrial plants is consumed for process heating applications, metal and glass manufacturers are discovering that process heating technologies provide significant opportunities for improving industrial productivity, energy efficiency, and global competitiveness. This fact sheet is the first in a series to describe such opportunities that can be realized in industrial systems by conducting plant-wide assessments (PWA).

77

Heat energy from hydrogen-metal nuclear interactions  

SciTech Connect (OSTI)

The discovery of the Fleischmann-Pons Effect in 1989, a promise of an abundant, cheap and clean energy source was premature in the sense that theoretical knowledge, relative technologies and the experimental tools necessary for understanding and for scale-up still were not available. Therefore the field, despite efforts and diversification remained quasi-stagnant, the effect (a scientific certainty) being of low intensity leading to mainstream science to reject the phenomenon and not supporting its study. Recently however, the situation has changed, a new paradigm is in statunascendi and the obstacles are systematically removed by innovative approaches. Defkalion, a Greek company (that recently moved in Canada for faster progress) has elaborated an original technology for the Ni-H system [1-3]. It is about the activation of hydrogen and creation of nuclear active nano-cavities in the metal through a multi-stage interaction, materializing some recent breakthrough announcements in nanotechnology, superconductivity, plasma physics, astrophysics and material science. A pre-industrial generator and a novel mass-spectrometry instrumentations were created. Simultaneously, a meta-theory of phenomena was sketched in collaboration with Prof. Y. Kim (Purdue U)

Hadjichristos, John [Defkalion GT SA, 1140 Homer Street, Suite 250, Vancouver BC V682X6 (Canada)] [Defkalion GT SA, 1140 Homer Street, Suite 250, Vancouver BC V682X6 (Canada); Gluck, Peter [Retired from INCDTIM Cluj-Napoca in 1999 (Romania)] [Retired from INCDTIM Cluj-Napoca in 1999 (Romania)

2013-11-13T23:59:59.000Z

78

SunShot Initiative: High Operating Temperature Liquid Metal Heat Transfer  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

High Operating Temperature Liquid Metal Heat Transfer Fluids High Operating Temperature Liquid Metal Heat Transfer Fluids UCLA logo University of California Berkeley logo Yale logo Four graphics in a grid that represent the sputtering technique being used in this project. Combinatorial screening and high throughput characterization of materials will be used to identify, develop, and demonstrate metal alloys that meet the MURI HOT Fluids targets suitable for CSP applications. The University of California, Los Angeles, the University of California, Berkeley, and Yale University The University of California, Los Angeles (UCLA), along with partners at the University of California, Berkeley, and Yale University, under the 2012 Multidisciplinary University Research Initiative (MURI): High Operating Temperature (HOT) Fluids funding opportunity, is investigating the use of metal alloys as a heat transfer fluid (HTF) in concentrating solar power (CSP) systems operating at temperatures in excess of 800°C. By allowing higher temperature operation, CSP systems can achieve greater efficiencies and thereby reduce the overall cost of electricity production.

79

Heating rates in collisionally opaque alkali-metal atom traps: Role of secondary collisions  

Science Journals Connector (OSTI)

Grazing collisions with background gas are the major cause of trap loss and trap heating in atom traps. To first order, these effects do not depend on the trap density. In collisionally opaque trapped atom clouds, however, scattered atoms with an energy E larger than the effective trap depth Eeff, which are destined to escape from the atom cloud, will have a finite probability for a secondary collision. This results in a contribution to the heating rate that depends on the column density ?nl? of the trapped atoms, i.e., the product of density and characteristic size of the trap. For alkali-metal atom traps, secondary collisions are quite important due to the strong long-range interaction with like atoms. We derive a simple analytical expression for the secondary heating rate, showing a dependency proportional to ?nl??Eeff1/2. When extrapolating to a vanishing column density, only primary collisions with the background gas will contribute to the heating rate. This contribution is rather small, due to the weak long-range interaction of the usual background gas species in an ultrahigh-vacuum system—He, Ne, or Ar—with the trapped alkali-metal atoms. We conclude that the transition between trap-loss collisions and heating collisions is determined by a cutoff energy 200??K<~Eeff<~400??K, much smaller than the actual trap depth E in most magnetic traps. Atoms with an energy Eeffheating rates for the alkali-metal atoms Li through Cs as a function of the effective trap depth, the column density of the trap, and the species in the background gas. The predictions of our model are in good agreement with the experimental data of Myatt for heating rates in high-density 87Rb-atom magnetic traps at JILA, including the effect of the rf shield and the composition of the background gas. It is shown that collisions with atoms from the Oort cloud also contribute to the heating rate. For 85Rb the calculated heating rate is below the experimentally observed value at JILA, supporting the idea that inelastic collisions in the trap are the major source of heating.

H. C. W. Beijerinck

2000-11-15T23:59:59.000Z

80

Liquid Metal Bond for Improved Heat Transfer in LWR Fuel Rods  

SciTech Connect (OSTI)

A liquid metal (LM) consisting of 1/3 weight fraction each of Pb, Sn, and Bi has been proposed as the bonding substance in the pellet-cladding gap in place of He. The LM bond eliminates the large AT over the pre-closure gap which is characteristic of helium-bonded fuel elements. Because the LM does not wet either UO2 or Zircaloy, simply loading fuel pellets into a cladding tube containing LM at atmospheric pressure leaves unfilled regions (voids) in the bond. The HEATING 7.3 heat transfer code indicates that these void spaces lead to local fuel hot spots.

Donald Olander

2005-08-24T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Pacific Power - Energy FinAnswer | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Pacific Power - Energy FinAnswer Pacific Power - Energy FinAnswer Pacific Power - Energy FinAnswer < Back Eligibility Agricultural Commercial Construction Fed. Government Industrial Installer/Contractor Institutional Local Government Nonprofit State Government Savings Category Heating & Cooling Home Weatherization Construction Commercial Weatherization Commercial Heating & Cooling Design & Remodeling Other Maximum Rebate Retrofit: 50% of the eligible energy efficiency measure cost Lighting: 50% of savings If incentive brings the simple payback below one year, the incentive is reduced so the simple payback equals one year. Program Info State California Program Type Utility Rebate Program Rebate Amount $0.12/kWh-$0.18/kWh annual energy savings + $50/kW average monthly on-peak demand savings

82

Continuous electric resistance heating—Hot forming system for high-alloy metals with poor workability  

Science Journals Connector (OSTI)

A new hot forming system for high-alloy metals with poor workability is developed. This forming system is a direct combination of a forming machine and continuous electric resistance heating, and is capable of the high-speed forming of metals with flexible and precise control of elevated temperature. The prototype of the new forming system is applied to the forming of high-alloy metals with poor formability, such as a Ti–6Al–4V bar, and the basic characteristics of this forming system are clarified. Using this system, sound, high speed forming of high alloys becomes possible, and the Ti–6Al–4V bar is successfully formed without fracture.

Jun Yanagimoto; Ryo Izumi

2009-01-01T23:59:59.000Z

83

The effects of a high temperature crystallization heat treatment on the corrosion behavior of MBF-75 metallic glass  

E-Print Network [OSTI]

THE EFFECTS OF A HIGH TEMPERATURE CRYSTALLIZATION HEAT TREATMENT ON THE CORROSION BEHAVIOR OF MBF-75 METALLIC GLASS A thesis by STEPHEN OAL OMENS Submitted to the Graduate College of Texas A & M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE August 1985 Major Subject: Mechanical Engineering THE EFFECTS OF A HIGH TEMPERATURE CRYSTALLIZATION HEAT TREATMENT ON THE CORROSION EEHAVIOR OF MBF-75 METALLIC GLASS A Thesis by STEPHEN DAL OWENS...

Owens, Stephen Dal

2012-06-07T23:59:59.000Z

84

Feasibility Investigation of the Decay Heat Removal Capability Using the Concept of a Thermosyphon in the Liquid Metal Reactor  

SciTech Connect (OSTI)

A new design concept for a decay heat removal system in a liquid metal reactor is proposed. The new design utilizes a thermosyphon to enhance the heat removal capacity and its heat transfer characteristics are analyzed against the current PSDRS (Passive Safety Decay heat Removal System) in the KALIMER (Korea Advanced Liquid Metal Reactor) design. The preliminary analysis results show that the new design with a thermosyphon yields substantial increase of 20{approx}40% in the decay heat removal capacity compared to the current design that do not have the thermosyphon. The new design reduces the temperature rise in the cooling air of the system and helps the surrounding structure in maintaining its mechanical integrity for long term operation at an accident. Also the analysis revealed the characteristics of the interactions among various heat transfer modes in the new design. (authors)

Yeon-Sik Kim; Yoon-Sub Sim; Eui-Kwang Kim [Korea Atomic Energy Research Institute, 150, Dukjin-Dong, Yusong-Gu, Taejon 305-353 (Korea, Republic of)

2002-07-01T23:59:59.000Z

85

Enhancement in hydrophobicity of silica films using metal acetylacetonate and heat treatment  

Science Journals Connector (OSTI)

Water is one of the most affecting chemicals that can cause damage to the solid surface. To protect the surface due to the action of water, the surface should be made hydrophobic. In the present study, the improvement in hydrophobicity of silica films using metal acetylacetonate (M-acac) by employing heat treatment to methyltrimethoxy silane (MTMS) based silica coatings is reported as a novel attempt. Instead of following the established trends of the surface derivatization or co-precursor method, iron acetylacetonate Fe(acac)3, copper acetylacetonate Cu(acac)2 and heat treatment were used to incorporate hydrophobicity with silica coatings. As M-acac is readily soluble in organic solvents, Fe(acac)3 and Cu(acac)2 were dissolved in methanol (MeOH) and their concentration was varied from 0 to 0.025 M. The coating solution was prepared by optimizing molar ratio of MTMS:MeOH:basic H2O to 1:7.15:6.34, respectively. Gelation time (tg) for Cu(acac)2 containing silica sol and that containing Fe(acac)3 were noted to be 30 and 55 min, respectively. The substrates were taken out after gelation and heat treated at 150 °C for 2 h. The heat treated films showed a dramatic increase in the static water contact angle from 82° to as high as 142°.

Sunetra L. Dhere; Uzma K.H. Bangi; Sanjay S. Latthe; A. Venkateswara Rao

2011-01-01T23:59:59.000Z

86

Study of integrated metal hydrides heat pump and cascade utilization of liquefied natural gas cold energy recovery system  

Science Journals Connector (OSTI)

The traditional cold energy utilization of the liquefied natural gas system needs a higher temperature heat source to improve exergy efficiency, which barricades the application of the common low quality thermal energy. The adoption of a metal hydride heat pump system powered by low quality energy could provide the necessary high temperature heat and reduce the overall energy consumption. Thus, an LNG cold energy recovery system integrating metal hydride heat pump was proposed, and the exergy analysis method was applied to study the case. The performance of the proposed integration system was evaluated. Moreover, some key factors were also theoretically investigated about their influences on the system performance. According to the results of the analysis, some optimization directions of the integrated system were also pointed out.

Xiangyu Meng; Feifei Bai; Fusheng Yang; Zewei Bao; Zaoxiao Zhang

2010-01-01T23:59:59.000Z

87

WASTE HEAT RECOVERY USING THERMOELECTRIC DEVICES IN THE LIGHT METALS INDUSTRY  

SciTech Connect (OSTI)

Recently discovered thermoelectric materials and associated manufacturing techniques (nanostructures, thin-film super lattice, quantum wells...) have been characterized with thermal to electric energy conversion efficiencies of 12-25+%. These advances allow the manufacture of small-area, high-energy flux (350 W/cm2 input) thermoelectric generating (TEG) devices that operate at high temperatures (~750°C). TEG technology offers the potential for large-scale conversion of waste heat from the exhaust gases of electrolytic cells (e.g., Hall-Hèroult cells) and from aluminum, magnesium, metal and glass melting furnaces. This paper provides an analysis of the potential energy recovery and of the engineering issues that are expected when integrating TEG systems into existing manufacturing processes. The TEG module must be engineered for low-cost, easy insertion and simple operation in order to be incorporated into existing manufacturing operations. Heat transfer on both the hot and cold-side of these devices will require new materials, surface treatments and design concepts for their efficient operation.

Choate, William T.; Hendricks, Terry J.; Majumdar, Rajita

2007-05-01T23:59:59.000Z

88

Formability of Al 5xxx Sheet Metals Using Pulsed Current for Various Heat Treatments  

SciTech Connect (OSTI)

Previous studies have shown that the presence of a pulsed electrical current, applied during the deformation process of an aluminum specimen, can significantly improve the formability of the aluminum without heating the metal above its maximum operating temperature range. The research herein extends these findings by examining the effect of electrical pulsing on 5052 and 5083 Aluminum Alloys. Two different parameter sets were used while pulsing three different heat treatments (As Is, 398°C, and 510°C) for each of the two aluminum alloys. For this research, the electrical pulsing is applied to the aluminum while the specimens are deformed, without halting the deformation process (a manufacturing technique known as Electrically-Assisted Manufacturing). The analysis focuses on establishing the effect the electrical pulsing has on the aluminum alloy’s various heat treatments by examining the displacement of the material throughout the testing region of dogbone-shaped specimens. The results from this research show that pulsing significantly increases the maximum achievable elongation of the aluminum (when compared to baseline tests conducted without electrical pulsing). Another beneficial effect produced by electrical pulsing is that the engineering flow stress within the material is considerably reduced. The electrical pulses also cause the aluminum to deform non-uniformly, such that the material exhibits a diffuse neck where the minimum deformation occurs near the ends of the specimen (near the clamps) and the maximum deformation occurs near the center of the specimen (where fracture ultimately occurs). This diffuse necking effect is similar to what can be experienced during superplastic deformation. However, when comparing the presence of a diffuse neck in this research, electrical pulsing does not create as significant of a diffuse neck as superplastic deformation. Electrical pulsing has the potential to be more efficient than traditional methods of incremental forming since the deformation process is never interrupted. Overall, with the greater elongation and lower stress, the aluminum can be deformed quicker, easier, and to a greater extent than is currently possible.

Salandro, Wesley A.; Jones, Joshua J.; McNeal, Timothy A.; Roth, John T.; Hong, Sung Tae; Smith, Mark T.

2010-10-01T23:59:59.000Z

89

Generation of high charge state metal ion beams by electron cyclotron resonance heating of vacuum arc plasma in cusp trap  

SciTech Connect (OSTI)

A method for generating high charge state heavy metal ion beams based on high power microwave heating of vacuum arc plasma confined in a magnetic trap under electron cyclotron resonance conditions has been developed. A feature of the work described here is the use of a cusp magnetic field with inherent ''minimum-B'' structure as the confinement geometry, as opposed to a simple mirror device as we have reported on previously. The cusp configuration has been successfully used for microwave heating of gas discharge plasma and extraction from the plasma of highly charged, high current, gaseous ion beams. Now we use the trap for heavy metal ion beam generation. Two different approaches were used for injecting the vacuum arc metal plasma into the trap - axial injection from a miniature arc source located on-axis near the microwave window, and radial injection from sources mounted radially at the midplane of the trap. Here, we describe preliminary results of heating vacuum arc plasma in a cusp magnetic trap by pulsed (400 {mu}s) high power (up to 100 kW) microwave radiation at 37.5 GHz for the generation of highly charged heavy metal ion beams.

Nikolaev, A. G.; Savkin, K. P.; Oks, E. M.; Vizir, A. V.; Yushkov, G. Yu. [High Current Electronics Institute, Siberian Division of Russian Academy Science, Tomsk 634055 (Russian Federation); Vodopyanov, A. V.; Izotov, I. V.; Mansfeld, D. A. [Institute of Applied Physics, Russian Academy of Science, Nizhniy Novgorod 603950 (Russian Federation)

2012-02-15T23:59:59.000Z

90

Use of impure inert gases in the controlled heating and cooling of mixed conducting metal oxide materials  

DOE Patents [OSTI]

Method for processing an article comprising mixed conducting metal oxide material. The method comprises contacting the article with an oxygen-containing gas and either reducing the temperature of the oxygen-containing gas during a cooling period or increasing the temperature of the oxygen-containing gas during a heating period; during the cooling period, reducing the oxygen activity in the oxygen-containing gas during at least a portion of the cooling period and increasing the rate at which the temperature of the oxygen-containing gas is reduced during at least a portion of the cooling period; and during the heating period, increasing the oxygen activity in the oxygen-containing gas during at least a portion of the heating period and decreasing the rate at which the temperature of the oxygen-containing gas is increased during at least a portion of the heating period.

Carolan, Michael Francis (Allentown, PA); Bernhart, John Charles (Fleetwood, PA)

2012-08-21T23:59:59.000Z

91

Failure analysis of spiral finned tube on the economizer  

Science Journals Connector (OSTI)

This article describes the results of an investigation about the failure of spiral finned tube on a newly designed and retrofitted low pressure economizer in a 300 MW pulverized-coal-fired power plant. In order to find out the failure causes and to suggest preventive measures, phase compositions and macrostructure of the tube metal surface were investigated by X-Ray Diffraction and Scanning Electron Microscope equipped with energy dispersive X-Ray spectroscopy micro-analysis. The results show that the failure was principally owing to comprehensive multiphase erosion, an interaction of the fly ash wearing, flue gas washing and sulfurous acid corrosion. Recommendations are given to minimize such failures.

ZhiYuan Liang; QinXin Zhao

2013-01-01T23:59:59.000Z

92

Pacific Power - Energy FinAnswer | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Industrial Industrial Institutional Local Government Nonprofit State Government Savings Category Other Heating & Cooling Home Weatherization Construction Commercial Weatherization Commercial Heating & Cooling Design & Remodeling Appliances & Electronics Commercial Lighting Lighting Maximum Rebate Retrofit: 60% of project cost Lighting: 50% of savings Incentives may not be available to reduce the project simple payback below one year Program Info State District of Columbia Program Type Utility Rebate Program Rebate Amount $0.15/kWh annual energy savings + $50/kW average monthly demand savings Provider Pacific Power Pacific Power's Energy FinAnswer program provides cash incentives to help its commercial and industrial customers improve their heating, cooling, refrigeration, compressed air, lighting, pumping or industrial processes.

93

E-Print Network 3.0 - accurate heat transfer Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Pennsylvania State University Collection: Engineering 11 Boiling heat transfer in a hydrofoil-based micro pin fin heat sink Summary: in large scatter and were not able to...

94

NGA98fin5.vp  

Gasoline and Diesel Fuel Update (EIA)

3 3 Consumption Total natural gas consumption declined during 1998 to 21.3 trillion cubic feet, 3 percent below the 1997 and 1996 levels. Warmer-than-normal winter temperatures in 1998 reduced the demand for natural gas for space heating in the residen- tial and commercial sectors. These declines during 1998 were partially offset by the increase in natural gas consump- tion by electric utilities. Since 1992, natural gas has accounted for nearly one-quarter of total energy consump- tion in the United States. · The residential sector had the largest decline (463 bil- lion cubic feet) in natural gas demand with 4.5 trillion cubic feet consumed, down 9 percent from the 1997 level and down 14 percent from the 1996 level. Much of the decline may be attributed to warmer-than-normal temperatures during the heating season (November through March) and the effects from El Nino in the Pacific region

95

Convective flow of refrigerant (R-123) across a bank of micro pin fins Ali Kosar, Yoav Peles *  

E-Print Network [OSTI]

, and pressure drop of R-123 over a bank of shrouded micro pin fins 243 lm long with hydraulic diameter of 99.5 lm. Heat transfer coefficients and Nusselt numbers have been obtained over effective heat fluxes studied in the context of turbine blade cooling. Nusselt number and friction factor correlations

Peles, Yoav

96

NGA98fin5.vp  

Gasoline and Diesel Fuel Update (EIA)

8 8 A4. Estimated Composition of Liquids Extracted at Natural Gas Processing Plants and the Resulting Heat Content Extraction Loss by State, 1998 (Liquid Volumes in Thousand Barrels, Heat Content in Billion Btu) Table Alabama ...................... 22 1,141 172 826 1,036 13,496 Alaska.......................... 0 1,319 3,490 9,724 19,356 150,419 Arkansas ..................... 39 51 29 110 137 1,536 California ..................... 18 2,159 2,523 1,377 2,274 34,826 Colorado...................... 6,345 5,096 875 2,205 2,946 65,730 Florida ......................... 546 521 0 335 157 5,856 Illinois .......................... 0 22 0 0 37 255 Kansas ........................ 6,605 14,223 2,450 4,751 4,823 127,491 Kentucky ..................... 274 823 79 275 211 6,476 Louisiana ..................... 33,494 29,514 9,727 10,370 18,252 384,288 Michigan ......................

97

Corrosion of heat-recovery exchangers in swimming-pool-hall ventilation systems. Research report  

SciTech Connect (OSTI)

The report concludes an investigation of the corrosion resistance of heat-recovery exchangers operating in swimming-pool-hall atmospheres. An interim report was published in August 1981. The trends detected then have been confirmed and it is concluded that exchangers using copper for both tubes and fins have adequate corrosion resistance and can be expected to remain efficient and structurally sound for more than ten years. Aluminium is shown to be unsuitable as a fin material because of its susceptibility to localized dissimilar metal corrosion when in contact with the copper tubes. Some of the steel components in the heat recovery chamber are apt to corrode badly and need to be protected, or else made out of non-corrodible materials. It is also important to filter the incoming air to prevent the exchangers becoming contaminated by airborne detritus.

Bird, T.L.

1985-09-01T23:59:59.000Z

98

Fabrication of superconducting metal-oxide textiles by heating impregnated polymeric material in a weakly oxidizing atmosphere  

SciTech Connect (OSTI)

A process is described for producing crystalline fibers, textiles or shapes comprised of YBa[sub 2]Cu[sub 3]O[sub 7[minus]x] where x varies from about 0 to about 0.4, said process comprising: (a) impregnating a preformed organic polymeric material with three metal compounds to provide metal elements in said material in substantially the atomic ratio occurring in said YBa[sub 2]Cu[sub 3]O[sub 7[minus]x]; (b) heating said impregnated material in a weakly oxidizing atmosphere containing from about 0.05% to about 2% oxygen by volume to a temperature sufficiently high to at least partially pyrolize and oxidize said organic material and at least partially oxidize said metal compounds substantially without ignition of said organic material and without formation of a molten phase or reaching a decomposition temperature of said YBa[sub 2]Cu[sub 3]O[sub 7[minus]x]; and (c) cooling the resulting material in at least a moderately oxidizing atmosphere to room temperature so as to obtain said fibers, textiles or shapes.

Van den Sype, J.S.

1993-07-13T23:59:59.000Z

99

NGA98fin5.vp  

Gasoline and Diesel Fuel Update (EIA)

An An overhead pipeline crossing on the White River near Newport, Arkansas. 237 Energy Information Administration / Natural Gas Annual 1998 Metric and Thermal Conversion Tables Metric Conversions Table B1 presents Summary Statistics for Natural Gas in the United States for 1994 through 1998 in metric units of mea- sure. Volumes are shown in cubic meters instead of cubic feet. Prices are shown in dollars per thousand cubic meters instead of dollars per thousand cubic feet. The data in this ta- ble have been converted from the data that appear in Table 1 of this report. Thermal Conversions Table B2 presents the thermal (Btu) conversion factors and the converted data for natural gas supply and disposition from 1994 through 1998. A brief documentation for the ther- mal conversion factors follows: · Marketed Production. The conversion factor is calcu- lated by adding the total heat content

100

NGA98fin5.vp  

Gasoline and Diesel Fuel Update (EIA)

0 0 · Residential consumers continue to pay the highest price for natural gas. The average price of natural gas deliveries to the residential sector declined by 2 percent ($0.12 per thousand cubic feet) from $6.94 in 1997 to $6.82 per thousand cubic feet in 1998, which was the smallest decrease of any of the consuming sectors. In recent years, only modest changes in constant dollars have been seen for residential prices (Figure 14). Most of these consumers remain captive to LDC sales ser- vice in all but a few States. The LDCs are obligated to supply gas to residences at all times, including during heating seasons when demand is high. Providing this premium service usually results in higher prices. · The second-highest prices for natural gas deliveries were seen in the commercial sector. The average price paid by commercial consumers fell 5 percent ($0.31 per thousand cubic feet) from

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

NGA98fin5.vp  

Gasoline and Diesel Fuel Update (EIA)

Energy Energy Information Administration / Natural Gas Annual 1998 State Volume of Natural Gas Delivered to Processing Plants (million cubic feet) Total Liquids Extracted (thousand barrels) Extraction Loss Located Within the State Located Outside of the State Total Processed Volume (million cubic feet Estimated Heat Content (billion Btu) Alabama ...................... 105,708 3,137 108,845 3,756 4,783 15,572 Alaska.......................... 2,966,461 0 2,966,461 33,889 40,120 150,419 Arkansas ..................... 198,148 4 198,152 365 451 1,536 California ..................... 235,558 0 235,558 8,351 10,242 34,826 Colorado...................... 424,984 766 425,750 17,541 24,401 66,018 Florida ......................... 5,037 0 5,037 967 939 3,632 Illinois .......................... 468 0 468 59 70 255 Kansas ........................ 600,453 2,170 602,623

102

The problems of weld metal or heat affected zone toughness in offshore structural steels  

SciTech Connect (OSTI)

An extensive set of fracture toughness results for welded offshore structural steels, gathered from nine separate sponsoring companies, has been entered into a specially constructed database. With over eleven thousand Charpy results and over two thousand CTOD results available, it has been possible to analyze the occurrence of low toughness results with respect to variables such as thickness, PWHT, steel production route etc., even though the individual test programs were not specifically structured to do this. This paper concentrates on the toughness of the weld metal. The data demonstrates that the likelihood of a low toughness result from a CTOD test in weld metal at {minus}10 C is comparable with that from the HAZ region for welded offshore structural steels, and PWHT of the joint is beneficial in reducing the occurrence of low toughness values in the weld metal. It is therefore important that when the HAZ performance is assessed, either through weld procedure tests or plate prequalification procedures, adequate attention is also paid to the weld metal toughness.

Hancock, P.; Spurrier, J.; Chubb, J.P. [Cranfield Univ. (United Kingdom). School of Industrial and Manufacturing Science

1996-12-01T23:59:59.000Z

103

ENHANCEMENT OF HEAT REMOVAL USING CONCAVE LIQUID METAL TARGETS FOR HIGH-POWER ACCELERATORS  

E-Print Network [OSTI]

areas for the production of intense beams of secondary particles (IFMIF, SNS, RIA, LHC). The energy metal flow targets can be useful for future accelerator projects such as RIA, SNS, and ILC [1 dump areas for the production of intense beams of secondary particles. The severe constraints arising

Harilal, S. S.

104

An investigation of the heat and mass transfer by free convection from humid air to a horizontal metal plate under frosting conditions  

E-Print Network [OSTI]

AN INVESTIOATION OF THE NEAT AND MASS TRANSFER BY FREE CONVECTION FROM HUMID AIR TO A HDRIZOHTAL METAL PLATE UNDER FROSTINO COND1TIONS A Thesis By BOBBY BELL~ JR. Submitted to the Graduate College of Texas A%M University in partial... ~ ~ ~. . . 60 - 61 17 Total Heat Transferred, to Plate vs. Time ~ 18 19 20 Thermal Conductivity Coefficient of Frost vso Time. . . . . . . . . . ~ ~ . . ~ ~ Heat Transfer Convective Coefficient vs. Time ~ 0 4 ~ 0 ~ ~ 4 ~ ~ ~ Resistivity of' Air...

Bell, Bobby

2012-06-07T23:59:59.000Z

105

Design of swimming fins to treat Patellofemoral Pain Syndrome  

E-Print Network [OSTI]

This thesis project involves developing a pair of swimming fins to strengthen the Vastus Medialis, or inner quadriceps muscle, to help patients with Patellofemoral Pain Syndrome. Configurations of mock up fins, made from ...

Tsai, Helen

2007-01-01T23:59:59.000Z

106

Proceedings of IWHT2011 2011 International Workshop on Heat Transfer Advances for  

E-Print Network [OSTI]

of Changes (AOC), was successfully developed in the authors' previous publications for solving the heat the capability of the AOC method to find out the optimal fin geometric variables (The fin spiral angle, fin the optimal solution in a short iterative process. Furthermore, the AOC and GA results outperform

Ghajar, Afshin J.

107

Metal-insulator transition upon heating and negative-differential-resistive-switching induced by self-heating in BaCo{sub 0.9}Ni{sub 0.1}S{sub 1.8}  

SciTech Connect (OSTI)

The layered compound BaCo{sub 1?x}Ni{sub x}S{sub 2?y} (0.05?metal to a high-T tetragonal antiferromagnetic insulator around 200?K with huge hysteresis (?40?K) and large volume change (?0.01). Here, we report on unusual voltage-controlled resistive switching followed by current-controlled resistive switching induced by self-heating in polycrystalline BaCo{sub 1?x}Ni{sub x}S{sub 2?y} (nominal x?=?0.1 and y?=?0.2). These were due to the steep metal to insulator transition upon heating followed by the activated behavior of the resistivity above the transition. The major role of Joule heating in switching is supported by the absence of nonlinearity in the current as function of voltage, I(V), obtained in pulsed measurements, in the range of electric fields relevant to d.c. measurements. The voltage-controlled negative differential resistance around the threshold for switching was explained by a simple model of self-heating. The main difficulty in modeling I(V) from the samples resistance as function of temperature R(T) was the progressive increase of R(T), and to a lesser extend the decrease of the resistance jumps at the transitions, caused by the damage induced by cycling through the transitions by heating or self-heating. This was dealt with by following systematically R(T) over many cycles and by using the data of R(T) in the heating cycle closest to that of the self-heating one.

Fisher, B.; Genossar, J.; Chashka, K. B.; Patlagan, L.; Reisner, G. M. [Physics Department, Technion-Israel Institute of Technology, Haifa 32000 (Israel)

2014-04-14T23:59:59.000Z

108

Development of Closure for Heat Exchangers Based on Volume Averaging Theory  

E-Print Network [OSTI]

Optimization for Pin-Fin Heat Sinks," Journal of ElectronicConvection," Journal of Heat Transfer, 115(1), pp. 75-81. [of spheres," Proc. 28th National Heat Transfer Conference,

Zhou, Feng

2014-01-01T23:59:59.000Z

109

Development of Friction Factor Correlation for Single-phase Flow in Micro-fin Tube Using Logistic Dose Response Curve  

E-Print Network [OSTI]

@umac.mo Abstract: Tam et al. [1] conducted simultaneous heat transfer and friction factor experiments for the plain the same as the plain tube. However, the friction factor characteristics of the micro-fin tubes in the transition region were different compared to the plain tube. This type of data cannot be easily correlated

Ghajar, Afshin J.

110

Heat removal aspects of Liquid Metal Fast Breeder Reactor safety in light of the Three Mile Island incident  

SciTech Connect (OSTI)

The safety aspects of the Liquid Metal Fast Breeder Reactor (LMFBR) loop design are compared with those of the Light Water Reactor (LWR), in light of the Three Mile Island (TMI) incident. The events at TMI are briefly described, the fundamental differences between the LWR water coolant and the LMFBR sodium coolant are presented, and the design of analogous LMFBR safety systems under similar events as those at TMI is discussed. A preliminary qualitative evaluation of a TMI-equivalent accident for an LMFBR indicates that there is likely to be: (1) negligible pressure transients in the primary loop, (2) no core damage, (3) isolation of the incident at the steam generator, and (4) no radiation release to the environment, except a negligible amount of tritium from the secondary sodium. Furthermore, with the absence of the ECCS (Emergency Core Cooling System), pressurizer, and other pressure-related components in the LMFBR design, operator action for a LMFBR should be much simpler in dealing with the coolant upset condition and the decay heat removal problems.

Victor, H.R.; Graf, D.G.

1980-12-01T23:59:59.000Z

111

Optimized design of a heat exchanger for an air-to-water reversible heat pump working with propane (R290)  

E-Print Network [OSTI]

Optimized design of a heat exchanger for an air-to-water reversible heat pump working with propane-to-water reversible heat pump unit was carried out using two different fin-and-tube heat exchanger ``coil'' designs concepts. The performance of the heat pump was evaluated for each coil design at different superheat

Fernández de Córdoba, Pedro

112

Heat rejection system  

DOE Patents [OSTI]

A cooling system for rejecting waste heat consists of a cooling tower incorporating a plurality of coolant tubes provided with cooling fins and each having a plurality of cooling channels therein, means for directing a heat exchange fluid from the power plant through less than the total number of cooling channels to cool the heat exchange fluid under normal ambient temperature conditions, means for directing water through the remaining cooling channels whenever the ambient temperature rises above the temperature at which dry cooling of the heat exchange fluid is sufficient and means for cooling the water.

Smith, Gregory C. (Richland, WA); Tokarz, Richard D. (Richland, WA); Parry, Jr., Harvey L. (Richland, WA); Braun, Daniel J. (Richland, WA)

1980-01-01T23:59:59.000Z

113

Modeling particle deposition on HVAC heat exchangers  

SciTech Connect (OSTI)

Fouling of fin-and-tube heat exchangers by particle deposition leads to diminished effectiveness in supplying ventilation and air conditioning. This paper explores mechanisms that cause particle deposition on heat exchanger surfaces. We present a model that accounts for impaction, diffusion, gravitational settling, and turbulence. Simulation results suggest that some submicron particles deposit in the heat exchanger core, but do not cause significant performance impacts. Particles between 1 and 10 {micro}m deposit with probabilities ranging from 1-20% with fin edge impaction representing the dominant mechanism. Particles larger than 10 {micro}m deposit by impaction on refrigerant tubes, gravitational settling on fin corrugations, and mechanisms associated with turbulent airflow. The model results agree reasonably well with experimental data, but the deposition of larger particles at high velocities is underpredicted. Geometric factors, such as discontinuities in the fins, are hypothesized to be responsible for the discrepancy.

Siegel, J.A.; Nazaroff, W.W.

2002-01-01T23:59:59.000Z

114

Efficient Heat Storage Materials: Metallic Composites Phase-Change Materials for High-Temperature Thermal Energy Storage  

SciTech Connect (OSTI)

HEATS Project: MIT is developing efficient heat storage materials for use in solar and nuclear power plants. Heat storage materials are critical to the energy storage process. In solar thermal storage systems, heat can be stored in these materials during the day and released at night—when the sun’s not out—to drive a turbine and produce electricity. In nuclear storage systems, heat can be stored in these materials at night and released to produce electricity during daytime peak-demand hours. MIT is designing nanostructured heat storage materials that can store a large amount of heat per unit mass and volume. To do this, MIT is using phase change materials, which absorb a large amount of latent heat to melt from solid to liquid. MIT’s heat storage materials are designed to melt at high temperatures and conduct heat well—this makes them efficient at storing and releasing heat and enhances the overall efficiency of the thermal storage and energy-generation process. MIT’s low-cost heat storage materials also have a long life cycle, which further enhances their efficiency.

None

2011-11-21T23:59:59.000Z

115

Pool boiling on nano-finned surfaces  

E-Print Network [OSTI]

is explored in this study. Experiments are conducted in a cubical test chamber containing fluoroinert coolant (PF5060, Manufacturer: 3M Co.) as the working fluid. Pool boiling experiments are conducted for saturation and subcooled conditions. Three...). .................................................................................................68 Fig. 19. Plots comparing the heat flux through the enhanced test surfaces (qw”) with the heat flux through the bare test surface (qb”) under 10 °C sub-cooling condition for both nulceate and film boiling regimes. Heat flux data...

Sriraman, Sharan Ram

2008-10-10T23:59:59.000Z

116

Metal-like heat conduction in laser-excited InSb probed by picosecond time-resolved x-ray diffraction  

Science Journals Connector (OSTI)

A semiconductor (InSb) showed transient metal-like heat conduction after excitation of a dense electron-hole plasma via short and intense light pulses. A related ultrafast strain relaxation was detected using picosecond time-resolved x-ray diffraction. The deduced heat conduction was, by a factor of 30, larger than the lattice contribution. The anomalously high heat conduction can be explained once the contribution from the degenerate photocarrier plasma is taken into account. The magnitude of the effect could provide the means for guiding heat in semiconductor nanostructures. In the course of this work, a quantitative model for the carrier dynamics in laser-irradiated semiconductors has been developed, which does not rely on any adjustable parameters or ad hoc assumptions. The model includes various light absorption processes (interband, free carrier, two photon, and dynamical Burstein-Moss shifts), ambipolar diffusion, energy transport (heat and chemical potential), electrothermal effects, Auger recombination, collisional excitation, and scattering (elastic and inelastic). The model accounts for arbitrary degrees of degeneracy.

P. Sondhauss, O. Synnergren, T. N. Hansen, S. E. Canton, H. Enquist, A. Srivastava, and J. Larsson

2008-09-10T23:59:59.000Z

117

E-Print Network 3.0 - anti-rotavirus al fin Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

anal fins differently in different gaits (Gordon et al., 2000; Hove et al., 2001). At swimming... fins provide thrust for the animal and the ... Source: Lauder, George V. -...

118

Pool boiling on nano-finned surfaces  

E-Print Network [OSTI]

The effect of nano-structured surfaces on pool boiling heat transfer is explored in this study. Experiments are conducted in a cubical test chamber containing fluoroinert coolant (PF5060, Manufacturer: 3M Co.) as the working fluid. Pool boiling...

Sriraman, Sharan Ram

2009-05-15T23:59:59.000Z

119

Critical Heat Flux -CHF in Liquid Metal in Presence of a Magnetic Field with Particular Reference to Fusion Reactor Project  

Science Journals Connector (OSTI)

Knowledge of the critical heat flux q??crit is a cornerstone of reactor design fission, but as will demonstrate also in fusion reactors. This quantity cannot be deduced directly,...

F. J. Arias

2010-04-01T23:59:59.000Z

120

Preying on the predator : the shark fin controversy  

E-Print Network [OSTI]

The consumption of shark fin soup dates back to the Ming Dynasty in China, when it was served to emperors. Today, the cultural delicacy represents wealth, status, and power. Over the past 30 years, with the rising middle ...

Morris, Alexandra H

2014-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Development of a plate-fin type gas turbine recuperator  

Science Journals Connector (OSTI)

A plate-fin type recuperator for a gas turbine/fuel cell hybrid power generation system was designed, manufactured, and tested. Performance analysis shows that the performance of the system is directly affecte...

Jae Su Kwak; Inyoung Yang

2006-07-01T23:59:59.000Z

122

Waste Heat Management Options: Industrial Process Heating Systems  

Broader source: Energy.gov (indexed) [DOE]

Heat Management Options Heat Management Options Industrial Process Heating Systems By Dr. Arvind C. Thekdi E-mail: athekdi@e3minc.com E3M, Inc. August 20, 2009 2 Source of Waste Heat in Industries * Steam Generation * Fluid Heating * Calcining * Drying * Heat Treating * Metal Heating * Metal and Non-metal Melting * Smelting, agglomeration etc. * Curing and Forming * Other Heating Waste heat is everywhere! Arvind Thekdi, E3M Inc Arvind Thekdi, E3M Inc 3 Waste Heat Sources from Process Heating Equipment * Hot gases - combustion products - Temperature from 300 deg. F. to 3000 deg.F. * Radiation-Convection heat loss - From temperature source of 500 deg. F. to 2500 deg. F. * Sensible-latent heat in heated product - From temperature 400 deg. F. to 2200 deg. F. * Cooling water or other liquids - Temperature from 100 deg. F. to 180 deg. F.

123

MODELING PARTICLE DEPOSITION ON HVAC HEAT EXCHANGERS  

E-Print Network [OSTI]

LBNL-49339 MODELING PARTICLE DEPOSITION ON HVAC HEAT EXCHANGERS J.A. Siegel1,3 * and W.W. Nazaroff2 Department of Energy under contract DE-AC03-76SF00098. #12;MODELING PARTICLE DEPOSITION ON HVAC HEAT, such as discontinuities in the fins, are hypothesized to be responsible for the discrepancy. INDEX TERMS HVAC, Fouling

124

Floatable solar heat modules  

SciTech Connect (OSTI)

A floating solar heat module for swimming pools comprises a solid surface for conducting heat from the sun's rays to the water and further includes a solid heat storage member for continual heating even during the night. A float is included to maintain the solar heat module on the surface of the pool. The solid heat storage medium is a rolled metal disk which is sandwiched between top and bottom heat conducting plates, the top plate receiving the heat of the sun's rays through a transparent top panel and the bottom plate transferring the heat conducted through the top plate and rolled disk to the water.

Ricks, J.W.

1981-09-29T23:59:59.000Z

125

Long-term corrosion measurements in condensing heat exchangers. Topical report, September 1989-January 1993  

SciTech Connect (OSTI)

Corrosion of metals used in condensing heat exchangers for gas appliances has been correlated most strongly with the chloride content of the condensate. This study presents results of an experimental examination of the long-term corrosion in metals used in condensing heat exchangers. The objective of this work is to develop a rationale for predicting the performance and expected service life of metals in condensing heat exchangers. Long-term exposure tests were conducted using finned-tube condensing heat exchangers containing tubes of 304L, 3161L, 3171L, Sea-Cure, and 29-4C steel, and aluminum. The natural gas was spiked with R-11 to generate chloride ion levels in the condensate of 3 ppm, 26 ppm, and 225 ppm. The aluminum tubes experienced through-the-wall pitting after 1.5 months at 225 ppm chloride, and after 6 months at 26 ppm chloride. At 3 ppm, most of the tubes exhibited no corrosion. At 225 ppm and 26 ppm, the 300-series stainless steels experienced through-the-wall corrosion within 3 months, but at 3 ppm virtually no corrosion was found. Sea-Cure and 29-4C exhibited the best corrosion resistance with some pitting at 225 ppm but none at 26 ppm and 3 ppm.

Stickford, G.H.; Hindin, B.

1993-01-31T23:59:59.000Z

126

Exergy analysis of second-generation micro heat sinks under single-phase and flow boiling conditions  

Science Journals Connector (OSTI)

A parametric study of exergy efficiency was conducted for five micro pin fin heat sinks of different spacing and shapes. Of the four micro pin fin heat sinks tested under single-phase flow conditions, those with better heat transfer performance yielded superior exergy efficiencies. The use of R-123 in place of water as working fluid was found to enhance exergetic performance at the expense of reduced heat transfer performance. The exergy analysis was also extended to the flow boiling of R-123 in an additional hydrofoil-based micro pin fin heat sink. It was found that exergy efficiencies decreased with mass velocity.

Ali Kosar

2010-01-01T23:59:59.000Z

127

Numerical simulation of intermediate heat exchanger of the liquid metal fast breeder reactor using COMMIX-1B  

E-Print Network [OSTI]

transfer correlation is made. ACKNOWLEDGEMENT I thank Dr. Yassin A. Hassan my advisor and commitee chair for his understand- ing, support, and enthusiasm for this project. My thanks also go to Drs. Costantine Tzanoz and Hang Dommanus from Argonne... hydraulic computer code. It is developed at Argonne National Laboratory (ANL) for a. Liquid Metal Fast Breeder Reactor (LMFBR). COMMIX-1B is the advanced version of COMMIX series that was first developed in 1976. s In this study, a nodalization...

Saleh, Habeeb H.

2012-06-07T23:59:59.000Z

128

Line patterning of (Sr,Ba)Nb{sub 2}O{sub 6} crystals in borate glasses by transition metal atom heat processing  

SciTech Connect (OSTI)

Some NiO-doped Bi{sub 2}O{sub 3},La{sub 2}O{sub 3}-SrO-BaO-Nb{sub 2}O{sub 5}-B{sub 2}O{sub 3} glasses giving the formation of strontium barium niobate Sr{sub 0.5}Ba{sub 0.5}Nb{sub 2}O{sub 6} (SBN) crystals with a tetragonal tungsten-bronze structure through conventional crystallization in an electric furnace have been developed, and SBN crystal lines have been patterned on the glass surface by heat-assisted (250-300 deg. C) laser irradiation and scanning of continuous-wave Nd:YAG laser (wavelength: 1064 nm). The surface morphology and the quality of SBN crystal lines are examined from measurements of confocal scanning laser micrographs and polarized micro-Raman scattering spectra. The surface morphology of SBN crystal lines changes from periodic bump structures to homogeneous structures, depending on laser scanning conditions. It is suggested that the line patterned at the laser irradiation condition of laser power P=1 W and of laser scanning speed S=1 {mu}m/s in 2NiO-4La{sub 2}O{sub 3}-16SrO-16BaO-32Nb{sub 2}O{sub 5}-30B{sub 2}O{sub 3} glass has a possibility of the orientation of SBN crystals along the laser scanning direction. The present study demonstrates that the transition metal atom heat processing (i.e., a combination of cw Nd:YAG laser and Ni{sup 2+} ions) is a novel technique for spatially selected crystallization of SBN crystals in glass. - Graphical abstract: This figure shows the polarization optical (a) and confocal scanning laser (b) micrographs for the sample obtained by heat-assisted (300 deg. C) Nd:YAG laser irradiation with a laser power of P=1 W and laser scanning speed of S=1 {mu}m/s in Glass C. The figure demonstrates that the transition metal atom heat processing (i.e., a combination of cw Nd:YAG laser and Ni{sup 2+} ions) is a novel technique for spatially selected crystallization of SBN crystals in glass.

Sato, M.; Honma, T.; Benino, Y. [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka-cho, Nagaoka 940-2188 (Japan); Komatsu, T. [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka-cho, Nagaoka 940-2188 (Japan)], E-mail: komatsu@mst.nagaokaut.ac.jp

2007-09-15T23:59:59.000Z

129

Relationship between low-temperature boson heat capacity peak and high-temperature shear modulus relaxation in a metallic glass  

SciTech Connect (OSTI)

Low-temperature (2 K{<=}T{<=}350 K) heat capacity and room-temperature shear modulus measurements ({nu}=1.4 MHz) have been performed on bulk Pd{sub 41.25}Cu{sub 41.25}P{sub 17.5} in the initial glassy, relaxed glassy, and crystallized states. It has been found that the height of the low-temperature Boson heat capacity peak strongly correlates with the changes in the shear modulus upon high-temperature annealing. It is this behavior that was earlier predicted by the interstitialcy theory, according to which dumbbell interstitialcy defects are responsible for a number of thermodynamic and kinetic properties of crystalline, (supercooled) liquid, and solid glassy states.

Vasiliev, A. N.; Voloshok, T. N. [Department of Low Temperature Physics and Superconductivity, M.V. Lomonosov Moscow State University, Moscow 119991 (Russian Federation); Granato, A. V.; Joncich, D. M. [Department of Physics, University of Illinois at Urbana-Champaign, 1110 West Greet Street, Urbana, Illinois 61801 (United States); Mitrofanov, Yu. P. [Department of General Physics, Voronezh State Pedagogical University, 86 Lenin Street, Voronezh 394043 (Russian Federation); Khonik, V. A. [Department of General Physics, Voronezh State Pedagogical University, 86 Lenin Street, Voronezh 394043 (Russian Federation); Research Center, Voronezh State University, Universitetskaya Sq. 1, 394006 Voronezh (Russian Federation)

2009-11-01T23:59:59.000Z

130

ICRF heating at JET: From operations with a metallic wall to the long term perspective of a DT campaign  

SciTech Connect (OSTI)

The first series of experiments with the ITER-like wall (ILW) will start mid-2011 with D plasmas and will continue through 2012-13 with H, {sup 4}He and D plasmas, and up to 2014-15, when a DT campaign is proposed. In this paper, the previous experience at JET is reviewed to set the scene for the future challenges of ICRF operation including change in the ICRF coupling, W impurity production and evaluation of localized power loads due the RF sheaths. development in a Beryllium/Tungsten environment of ICRF heating schemes for the non activated and the DT phases of ITER.

Mayoral, M.-L.; Graham, M.; Jacquet, Ph.; Monakhov, I.; Riccardo, V. [Euratom/CCFE Fusion Association, Culham Science Centre, OX14 3DB (United Kingdom); Colas, L. [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Eriksson, L.-G. [European Commission, Brussels, B-1049 (Belgium); Lerche, E.; Van Eester, D. [LPP-ERM/KMS, Association Euratom-'Belgian State' (Belgium)

2011-12-23T23:59:59.000Z

131

DESIGN AND PERFORMANCE OF A FISH FIN-LIKE PROPULSOR FOR AUVS George V. Lauder1  

E-Print Network [OSTI]

for AUVs based on the mechanical design and performance of fish fins. II. THE SUNFISH MODEL SYSTEM Bluegill are able to execute highly effective yaw maneuvers using only their pectoral fins, and at speeds of less

Lauder, George V.

132

E-Print Network 3.0 - active vertical fin Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Summary: active to tilt the caudal fin at an angle to the vertical 26. In some fish, especially those known... . Low-aspect ratio pectoral fins in sharks function to alter...

133

Active Control of Smart Fin Model for Aircraft Buffeting Load Alleviation Applications  

E-Print Network [OSTI]

vertical fin structure, an investigation has been performed to understand the aerodynamic effects of high-speed vortical flows on the dynamic characteristics of vertical fin structures. Extensive wind-tunnel tests have increased with airflow speed as well as the vertical fin angle of attack relative to the airflow direction

Yaman, Yavuz

134

2,3,7,8-Tetrachlorodibenzo-p-dioxin Inhibits Zebrafish Caudal Fin Regeneration  

E-Print Network [OSTI]

2,3,7,8-Tetrachlorodibenzo-p-dioxin Inhibits Zebrafish Caudal Fin Regeneration Jeanmarie M. Zodrow- chlorodibenzo-p-dioxin (TCDD). Zebrafish caudal fins were par- tially amputated, and the fish received. Key Words: zebrafish; fin regeneration; aryl hydrocarbon recep- tor; AHR; 2,3,7,8-tetrachlorodibenzo-p-dioxin

Tullos, Desiree

135

The Coupling Performance of a Solar-Air Heat Pump  

Science Journals Connector (OSTI)

Based on the advantages and disadvantages of single air source heat pump, single solar energy heat pump and switch solar-air dual heat source heat pumps, a new type of solar-air composite heat source heat pump system has been proposed to realize the utilization and complementary advantages of two renewable energy: air and solar. It also provided a feasible method to improve the city's ecological environment, and plays a leading role in the villages and small towns’ construction. Design the composite heat exchanger with double heat sources. The heat exchanger had dual function of tube-fin and tube heat exchangers, break through the traditional model that heat exchanger in working can realize heat exchange only between the same gases or liquid heat sources, and realized the heat exchange between two heat sources. It laid the technological and equips mental foundation for realizing the synchronization and composite using of solar energy and air.

Yin Liu; Jing Ma; Guanghui Zhou

2011-01-01T23:59:59.000Z

136

HVAC Optimized Heat Exchangers Research Project | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Optimized Heat Exchangers Research Optimized Heat Exchangers Research Project HVAC Optimized Heat Exchangers Research Project The U.S. Department of Energy is currently conducting research into heating, ventilation, and air conditioning (HVAC) optimized heat exchangers. The information generated in this study will demonstrate performance improvements that can be achieved through optimization of refrigerant circuitry for non-uniform inlet air distribution. The tubing circuitry on fin-tube heat exchangers used in residential space-conditioning systems is typically designed assuming uniform airflow through the finned passageways. However, the air flow in installed systems is highly non-uniform, resulting in mismatched refrigerant-air heat transfer that reduces the capacity of the heat exchanger and efficiency of

137

Prediction of forces and moments on finned bodies at high angle of attack in transonic flow  

SciTech Connect (OSTI)

This report describes a theoretical method for the prediction of fin forces and moments on bodies at high angle of attack in subsonic and transonic flow. The body is assumed to be a circular cylinder with cruciform fins (or wings) of arbitrary planform. The body can have an arbitrary roll (or bank) angle, and each fin can have individual control deflection. The method combines a body vortex flow model and lifting surface theory to predict the normal force distribution over each fin surface. Extensive comparisons are made between theory and experiment for various planform fins. A description of the use of the computer program that implements the method is given.

Oberkampf, W. L.

1981-04-01T23:59:59.000Z

138

Nanofluid heat capacities  

Science Journals Connector (OSTI)

Significant increases in the heat capacity of heat transfer fluids are needed not only to reduce the costs of liquid heating and cooling processes but also to bring clean energy producing technologies like concentrating solar power (CSP) to price parity with conventional energy generation. It has been postulated that nanofluids could have higher heat capacities than conventional fluids. In this work nano- and micron-sized particles were added to five base fluids (poly-? olefin mineral oil ethylene glycol a mixture of water and ethylene glycol and calcium nitrate tetrahydrate) and the resulting heat capacities were measured and compared with those of the neat base fluids and the weighted average of the heat capacities of the components. The particles used were inert metals and metal oxides that did not undergo any phase transitions over the temperature range studied. In the nanofluids studied here we found no increase in heat capacity upon the addition of the particles larger than the experimental error.

Anne K. Starace; Judith C. Gomez; Jun Wang; Sulolit Pradhan; Greg C. Glatzmaier

2011-01-01T23:59:59.000Z

139

Turbulent convection in liquid metal with and without rotation  

E-Print Network [OSTI]

is the efficiency of convective heat transfer (Nu). In general, we find that the convective behavior of liquid metal=ðkT�, where q is total heat flux and k is the fluid's thermal conductivity. Heat flux q is total heat power P by turbulent, rotating convection in liquid metal. Liquid metals are peculiar in that they diffuse heat more

140

The Disruption of Vessel-Spanning Bubbles with Sloped Fins in Flat-Bottom and 2:1 Elliptical-Bottom Vessels  

SciTech Connect (OSTI)

Radioactive sludge was generated in the K-East Basin and K-West Basin fuel storage pools at the Hanford Site while irradiated uranium metal fuel elements from the N Reactor were being stored and packaged. The fuel has been removed from the K Basins, and currently, the sludge resides in the KW Basin in large underwater Engineered Containers. The first phase to the Sludge Treatment Project being led by CH2MHILL Plateau Remediation Company (CHPRC) is to retrieve and load the sludge into sludge transport and storage containers (STSCs) and transport the sludge to T Plant for interim storage. The STSCs will be stored inside T Plant cells that are equipped with secondary containment and leak-detection systems. The sludge is composed of a variety of particulate materials and water, including a fraction of reactive uranium metal particles that are a source of hydrogen gas. If a situation occurs where the reactive uranium metal particles settle out at the bottom of a container, previous studies have shown that a vessel-spanning gas layer above the uranium metal particles can develop and can push the overlying layer of sludge upward. The major concern, in addition to the general concern associated with the retention and release of a flammable gas such as hydrogen, is that if a vessel-spanning bubble (VSB) forms in an STSC, it may drive the overlying sludge material to the vents at the top of the container. Then it may be released from the container into the cell’s secondary containment system at T Plant. A previous study demonstrated that sloped walls on vessels, both cylindrical coned-shaped vessels and rectangular vessels with rounded ends, provided an effective approach for disrupting a VSB by creating a release path for gas as a VSB began to rise. Based on the success of sloped-wall vessels, a similar concept is investigated here where a sloped fin is placed inside the vessel to create a release path for gas. A key potential advantage of using a sloped fin compared to a vessel with a sloped wall is that a small fin decreases the volume of a vessel available for sludge storage by a very small fraction compared to a cone-shaped vessel. The purpose of this study is to quantify the capability of sloped fins to disrupt VSBs and to conduct sufficient tests to estimate the performance of fins in full-scale STSCs. Experiments were conducted with a range of fin shapes to determine what slope and width were sufficient to disrupt VSBs. Additional tests were conducted to demonstrate how the fin performance scales with the sludge layer thickness and the sludge strength, density, and vessel diameter based on the gravity yield parameter, which is a dimensionless ratio of the force necessary to yield the sludge to its weight.( ) Further experiments evaluated the difference between vessels with flat and 2:1 elliptical bottoms and a number of different simulants, including the KW container sludge simulant (complete), which was developed to match actual K-Basin sludge. Testing was conducted in 5-in., 10-in., and 23-in.-diameter vessels to quantify how fin performance is impacted by the size of the test vessel. The most significant results for these scale-up tests are the trend in how behavior changes with vessel size and the results from the 23-in. vessel. The key objective in evaluating fin performance is to determine the conditions that minimize the volume of a VSB when disruption occurs because this reduces the potential for material inside the STSC from being released through vents.

Gauglitz, Phillip A.; Buchmiller, William C.; Jenks, Jeromy WJ; Chun, Jaehun; Russell, Renee L.; Schmidt, Andrew J.; Mastor, Michael M.

2010-09-22T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Heat Source Lire,  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Source Lire, Source Lire, (liayrICS-25 ) tooling Tulles (Ai 1,06:1) - 11 (31.118 Module Stack Thermoelectric Module:, (14) ltcal L/Mr r a it i lli tisli Block Mounting Interface MMRTG Design Housing (At 2219) Fin (At Go63) Thermal Insulation (Min-K & Microtherm) Space Radioisotope Power Systems Multi-Mission Radioisotope Thermoelectric Generator January 2008 What is a Multi-Mission Radioisotope Thermoelectric Generator? Space exploration missions require safe, reliable, long-lived power systems to provide electricity and heat to spacecraft and their science instruments. A uniquely capable source of power is the radioisotope thermoelectric generator (RTG) - essentially a nuclear battery that reliably converts heat into electricity. The Department of Energy and NASA are developing

142

Understanding the Hydrodynamics of Swimming: From Fish Fins to Flexible Propulsors for Autonomous  

E-Print Network [OSTI]

Understanding the Hydrodynamics of Swimming: From Fish Fins to Flexible Propulsors for Autonomous. The research effort described here is concerned with developing a maneuvering propulsor for an autonomous

Lauder, George V.

143

E-Print Network 3.0 - active suichoku fin Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

vortical flows on the dynamic characteristics of vertical fin structures. Extensive wind-tunnel ... Source: Yaman, Yavuz - Department of Aerospace Engineering, Middle East...

144

The Big Picture on Process Heating | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

& Publications Install Waste Heat Recovery Systems for Fuel-Fired Furnaces Metal and Glass Manufacturers Reduce Costs by Increasing Energy Efficiency in Process Heating Systems...

145

Rocky Mountain Power - Energy FinAnswer | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

50% of eligible measure cost 50% of eligible measure cost Lighting Energy Savings Limit: 50%-75% of savings Payback Cap: 1 year; if incentive brings the simple payback below one year, the incenive is reduced so the simple payback equals one year Program Info State Idaho Program Type Utility Rebate Program Rebate Amount $0.12/kWh annual energy savings + $50/kW average monthly on-peak demand savings Provider Rocky Mountain Power Rocky Mountain Power's Energy FinAnswer program provides incentives to help its customers improve the efficiency of existing facilities and build new facilities that are significantly more efficient than code. New construction and retrofit projects for all industrial facilities can participate as well as all new commercial projects and commercial retrofits in facilities larger than 20,000 square feet.

146

Rocky Mountain Power - Energy FinAnswer | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

70% project cost 70% project cost New Construction: 50% Lighting: 50%-75% of savings Program Info State Wyoming Program Type Utility Rebate Program Rebate Amount $0.15/kWh annual energy savings + $50/kW average monthly demand savings Provider Rocky Mountain Power Rocky Mountain Power's Energy FinAnswer program provides incentives to help its customers improve the efficiency of existing facilities and build new facilities that are significantly more efficient than code. New construction and retrofit projects for all industrial facilities can participate as well as all new commercial projects and commercial retrofits in facilities larger than 20,000 square feet. Rocky Mountain Power will be involved from the beginning of the construction process. They will start by reviewing the facility plans and

147

Methods and criteria for safety analysis (FIN L2535)  

SciTech Connect (OSTI)

In response to the NRC request for a proposal dated October 20, 1992, Westinghouse Savannah River Company (WSRC) submit this proposal to provide contractural assistance for FIN L2535, ``Methods and Criteria for Safety Analysis,`` as specified in the Statement of Work attached to the request for proposal. The Statement of Work involves development of safety analysis guidance for NRC licensees, arranging a workshop on this guidance, and revising NRC Regulatory Guide 3.52. This response to the request for proposal offers for consideration the following advantages of WSRC in performing this work: Experience, Qualification of Personnel and Resource Commitment, Technical and Organizational Approach, Mobilization Plan, Key Personnel and Resumes. In addition, attached are the following items required by the NRC: Schedule II, Savannah River Site - Job Cost Estimate, NRC Form 189, Project and Budget Proposal for NRC Work, page 1, NRC Form 189, Project and Budget Proposal for NRC Work, page 2, Project Description.

Not Available

1992-12-01T23:59:59.000Z

148

Transient response of an industrial fin tube heat exchanger to flow variations  

E-Print Network [OSTI]

systems are usually classified as transient response or frequency response procedures that information yielded by one method is related to the other. They utilized this fact by using Fourier transformation theory to compute the frequency response...

Rana, Gopalji Motiram

2012-06-07T23:59:59.000Z

149

Corrosion of Aluminum-fin, Copper-tube Heat Exchange Coils  

E-Print Network [OSTI]

industry standard procedures to test process chemicals or application contaminants for copper tube corrosion potential. Industry supported research has begun to develop a bench test for this....

Field, J. E.

2002-01-01T23:59:59.000Z

150

Biologically-Inspired Adaptive Pectoral-Like Fin Control System For CFD Parameterized AUV  

E-Print Network [OSTI]

on the normalized gradient scheme. In the closed-loop system, time-varying yaw an- gle reference trajectoriesBiologically-Inspired Adaptive Pectoral-Like Fin Control System For CFD Parameterized AUV Mugdha S fin control, Adaptive control, Yaw plane control. Abstract- This paper treats the question of adaptive

Mittal, Rajat

151

Development of New Grid-Fin Design for Aerodynamic Marco Debiasi1  

E-Print Network [OSTI]

1 Development of New Grid-Fin Design for Aerodynamic Control Marco Debiasi1 Temasek Laboratories of attack = angle of the sharp leading edge = swept-back angle I. Introduction grid fin is an aerodynamic Aerodynamics Conference, Chicago, Illinois, 28 June - 1 July 2010, and as Paper 2012-2909 at the 30th AIAA

Debiasi, Marco

152

Are Tax and Non-Tax Factors Associated with FIN 48 Disclosures?  

E-Print Network [OSTI]

aggressiveness. Finally, I split the sample based on firms’ use of discretion over recognizing the tax benefits of aggressive tax positions prior to FIN 48 adoption. I find that firms which aggressively recognize tax benefits prior to FIN 48 adoption (i.e. firms...

McDonald, Janet L.

2011-10-21T23:59:59.000Z

153

FedFinAssistOpportuntiesatDOEBooklet.pdf | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

efficient, scalable, and low cost thermoelectric waste heat recovery devices for vehicles CX-010152: Categorical Exclusion Determination Recovery Act: Clean Coal Power Initiative...

154

Microsoft Word - 12-9076324.001_fin.doc  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Under Level A and B start-up shutdown Reactor trip conditions Under Level C Loss of heat sink Depressurized Conduction Cooldown situation (only for RPV) The ASME...

155

Development of a Solar Assisted Drying System Using Double-Pass Solar Collector with Finned Absorber  

Science Journals Connector (OSTI)

The Solar Energy Research Group, Universiti Kebangsaan Malaysia, International Islamic University Malaysia and Yayasan FELDA has designed and constructed a solar assisted drying system at OPF FELDA Factory, Felda Bukit Sagu 2, Kuantan, Pahang. The drying system has a total of six double-pass solar collectors. Each collector has a length of 480 cm and a width of 120 cm. The first channel depth is 3.5 cm and the second channel depth is 7 cm. Longitudinal fins made of angle aluminium, 0.8 mm thickness were attached to the bottom surface of the absorber plate. The solar collectors are arranged as two banks of three collectors each in series. Internal manifold are used to connect the collectors. Air enters through the first channel and then through the second channel of the collector. An auxiliary heater source is installed to supply heat under unfavourable solar radiation condition. An on/off controller is used to control the startup and shutdown of the auxiliary heater. An outlet temperature of 70–75 °C can be achieved at solar radiation range of 800–900 W/m2 and flow rate of 0.12 kg/s. The average thermal efficiency of a solar collector is approximately 37%.

M S M Azmi; M Y Othman; K Sopian; M H Ruslan; Z A A Majid; A Fudholi; J M Yasin

2012-01-01T23:59:59.000Z

156

Liquid metal thermal electric converter  

DOE Patents [OSTI]

A liquid metal thermal electric converter which converts heat energy to electrical energy. The design of the liquid metal thermal electric converter incorporates a unique configuration which directs the metal fluid pressure to the outside of the tube which results in the structural loads in the tube to be compressive. A liquid metal thermal electric converter refluxing boiler with series connection of tubes and a multiple cell liquid metal thermal electric converter are also provided.

Abbin, Joseph P. (Albuquerque, NM); Andraka, Charles E. (Albuquerque, NM); Lukens, Laurance L. (Albuquerque, NM); Moreno, James B. (Albuquerque, NM)

1989-01-01T23:59:59.000Z

157

Thermal response of a flat heat pipe sandwich structure to a localized heat flux  

E-Print Network [OSTI]

metal foam wick and distilled water as the working fluid. Heat was applied via a propane torch and radiative heat transfer. A novel method was developed to estimate experimentally, the heat flux distribution rights reserved. Keywords: Flat heat pipe; Thermal spreader; Heat transfer; Evaporator; Condenser 1

Wadley, Haydn

158

HVAC Radial Air Bearing Heat Exchangers Research Project | Department of  

Broader source: Energy.gov (indexed) [DOE]

Radial Air Bearing Heat Exchangers Radial Air Bearing Heat Exchangers Research Project HVAC Radial Air Bearing Heat Exchangers Research Project The U.S. Department of Energy is currently conducting research into heating, ventilation, and air conditioning (HVAC) radial air bearing heat exchangers. Rotary air bearing heat exchanger technology simultaneously solves four long standing problems of conventional "fan-plus-finned-heat-sink" heat exchangers. Project Description This project seeks to design, fabricate, and test successive generations of prototype radial air bearing heat exchanger devices based on lessons learned and further insights into device optimization, computational fluid dynamic studies for parametric optimization and determination of scaling laws, and laboratory measurement of flow field and heat transfer

159

Metal and Glass Manufacturers Reduce Costs by Increasing Energy...  

Broader source: Energy.gov (indexed) [DOE]

Metal and Glass Manufacturers Reduce Costs by Increasing Energy Efficiency in Process Heating Systems Metal and Glass Manufacturers Reduce Costs by Increasing Energy Efficiency in...

160

Microsoft Word - win0304_Version3Fin.doc  

Gasoline and Diesel Fuel Update (EIA)

3) 3) 1 Winter Fuels Outlook: 2003-2004 Introduction This report summarizes the winter outlook for demand, supply and prices for natural gas, heating oil, electricity and propane, with emphasis on residential space-heating demand. The outlook, which includes severe- and mild- weather cases, is consistent with the October 2003 Short-Term Energy Outlook. For the purposes of the analysis, the winter season is defined as the period from October through March. Highlights * Net changes in residential heating prices and expenditures compared to last winter are: Prices: almost no change for heating oil and propane; plus 9 percent for natural gas; plus 3 percent for electricity. Expenditures: minus 8 percent for heating oil; plus 5 percent for natural gas; plus 2 percent for electricity;

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Deposition of biological aerosols on HVAC heat exchangers  

SciTech Connect (OSTI)

Many biologically active materials are transported as bioaerosols 1-10 {micro}m in diameter. These particles can deposit on cooling and heating coils and lead to serious indoor air quality problems. This paper investigates several of the mechanisms that lead to aerosol deposition on fin and tube heat exchangers. A model has been developed that incorporates the effects of several deposition mechanisms, including impaction, Brownian and turbulent diffusion, turbophoresis, thermophoresis, diffusiophoresis, and gravitational settling. The model is applied to a typical range of air velocities that are found in commercial and residential HVAC systems 1 - 6 m/s (200 - 1200 ft/min), particle diameters from 1 - 8 {micro}m, and fin spacings from 3.2 - 7.9 fins/cm (8 - 16 fins/inch or FPI). The results from the model are compared to results from an experimental apparatus that directly measures deposition on a 4.7 fins/cm (12 FPI) coil. The model agrees reasonably well with this measured data and suggests that cooling coils are an important sink for biological aerosols and consequently a potential source of indoor air quality problems.

Siegel, Jeffrey; Walker, Ian

2001-09-01T23:59:59.000Z

162

Synthesis of Nanostructured Carbides of Titanium and Vanadium from Metal Oxides and Ferroalloys Through High-energy Mechanical Milling and Heat Treatment  

SciTech Connect (OSTI)

Carbides of Ti and V have been synthesized directly from their oxides and ferroalloys through mechanical milling and heat treatment. The powder mixtures are milled in a planetary ball mill from 15-80 hours and subsequently heat treated at 1000-1300 deg. C for TiO{sub 2}-C mixtures, at 500-550 deg. C for V{sub 2}O{sub 5}-C mixtures and at 600-1000 deg. C for (Fe-V)-C mixtures. The milled and heat treated powders are characterized by SEM, EDAX, XRD, and BET techniques. Nanostructured TiC has been successfully synthesized under suitable processing conditions. However, carbides of vanadium is unidentified even though possibilities of V{sub 2}O{sub 5}-C reaction are indicated with an extent of induced amorphism in the powder mixture. Density, specific surface area and particle size of the milled and heat treated mixtures are correlated with heat treatment temperatures. Similar attempts are also made to synthesize vanadium carbides from industrial grade Fe-V.

Basu, P.; Jian, P. F.; Seong, K. Y.; Seng, G. S.; Hussain, Z.; Aziz, A. [School of Materials and Minerals Resources Engineering, Universiti Sains Malaysia (USM), Engineering Campus, 14300 Nibong Tebal, Pulau Pinang (Malaysia); Masrom, A. K. [Advanced Materials Research Centre (AMREC), SIRIM Bhd, Kulim Hi-Tech Park, Kulim 09000 (Malaysia)

2010-03-11T23:59:59.000Z

163

Visual investigation on the heat dissipation process of a heat sink by using digital holographic interferometry  

SciTech Connect (OSTI)

We present a method for visually and quantitatively investigating the heat dissipation process of plate-fin heat sinks by using digital holographic interferometry. A series of phase change maps reflecting the temperature distribution and variation trend of the air field surrounding heat sink during the heat dissipation process are numerically reconstructed based on double-exposure holographic interferometry. According to the phase unwrapping algorithm and the derived relationship between temperature and phase change of the detection beam, the full-field temperature distributions are quantitatively obtained with a reasonably high measurement accuracy. And then the impact of heat sink's channel width on the heat dissipation performance in the case of natural convection is analyzed. In addition, a comparison between simulation and experiment results is given to verify the reliability of this method. The experiment results certify the feasibility and validity of the presented method in full-field, dynamical, and quantitative measurement of the air field temperature distribution, which provides a basis for analyzing the heat dissipation performance of plate-fin heat sinks.

Wu, Bingjing; Zhao, Jianlin, E-mail: jlzhao@nwpu.edu.cn; Wang, Jun; Di, Jianglei; Chen, Xin; Liu, Junjiang [Key Laboratory of Space Applied Physics and Chemistry, Ministry of Education, and Shaanxi Key Laboratory of Optical Information Technology, School of Science, Northwestern Polytechnical University, Xi'an 710072 (China)

2013-11-21T23:59:59.000Z

164

Solid0Core Heat-Pipe Nuclear Batterly Type Reactor  

SciTech Connect (OSTI)

This project was devoted to a preliminary assessment of the feasibility of designing an Encapsulated Nuclear Heat Source (ENHS) reactor to have a solid core from which heat is removed by liquid-metal heat pipes (HP).

Ehud Greenspan

2008-09-30T23:59:59.000Z

165

Cooling system having reduced mass pin fins for components in a gas turbine engine  

DOE Patents [OSTI]

A cooling system having one or more pin fins with reduced mass for a gas turbine engine is disclosed. The cooling system may include one or more first surfaces defining at least a portion of the cooling system. The pin fin may extend from the surface defining the cooling system and may have a noncircular cross-section taken generally parallel to the surface and at least part of an outer surface of the cross-section forms at least a quartercircle. A downstream side of the pin fin may have a cavity to reduce mass, thereby creating a more efficient turbine airfoil.

Lee, Ching-Pang; Jiang, Nan; Marra, John J

2014-03-11T23:59:59.000Z

166

Advances in the Research of Heat Pump Water Heaters  

E-Print Network [OSTI]

ICEBO2006, Shenzhen, China Renewable Energy Resources and a Greener Future Vol.VIII-12-2 1 Advances in the Research of Heat Pump Water Heaters Shangli Shan Dandan Wang Ruixiang Wang Master Master Professor Beijing...) [21] Wang sui-lin . Affection on fin-and-tube Heat Exchanger's Properties by non azeotropic mixtures[J] . Fluid machinery , 1996 , 24 (5) [22] Ge run-ting . Foundation of Dynamic Parameter Model and Theoritical Calculation of Evaporator...

Shan, S.; Wang, D.; Wang, R.

2006-01-01T23:59:59.000Z

167

Sodium heat engine electrical feedthrough  

DOE Patents [OSTI]

A thermoelectric generator device which converts heat energy to electrical energy is disclosed. An alkali metal is used with a solid electrolyte and a hermetically sealed feedthrough structure. 4 figs.

Weber, N.

1985-03-19T23:59:59.000Z

168

Dopant characterization in self-regulatory plasma doped fin field-effect transistors by atom probe tomography  

SciTech Connect (OSTI)

Fin field-effect transistors are promising next-generation electronic devices, and the identification of dopant positions is important for their accurate characterization. We report atom probe tomography (APT) of silicon fin structures prepared by a recently developed self-regulatory plasma doping (SRPD) technique. Trenches between fin-arrays were filled using a low-energy focused ion beam to directly deposit silicon, which allowed the analysis of dopant distribution by APT near the surface of an actual fin transistor exposed to air. We directly demonstrate that SRPD can achieve a boron concentration above 1 x 10{sup 20} atoms/cm{sup 3} at the fin sidewall.

Takamizawa, H.; Shimizu, Y.; Nozawa, Y.; Toyama, T.; Nagai, Y. [Oarai Center, Institute for Materials Research, Tohoku University, Oarai, Ibaraki 311-1313 (Japan); Morita, H.; Yabuuchi, Y.; Ogura, M. [Panasonic Corporation, Moriguchi, Osaka 570-8501 (Japan)

2012-02-27T23:59:59.000Z

169

Theoretical and experimental estimation of limiting input heat flux for thermoelectric power generators with passive cooling  

Science Journals Connector (OSTI)

Abstract This paper focuses on theoretical and experimental analysis used to establish the limiting heat flux for passively cooled thermoelectric generators (TEG). 2 commercially available TEG’s further referred as type A and type B with different allowable hot side temperatures (150 °C and 250 °C respectively) were investigated in this research. The thermal resistance of TEG was experimentally verified against the manufacturer’s specifications and used for theoretical analysis in this paper. A theoretical model is presented to determine the maximum theoretical heat flux capacity of both the TEG’s. The conventional methods are used for cooling of TEG’s and actual limiting heat flux is experimentally established for various cold end cooling configurations namely bare plate, finned block and heat pipe with finned condenser. Experiments were performed on an indoor setup and outdoor setup to validate the results from the theoretical model. The outdoor test setup consist of a fresnel lens solar concentrator with manual two axis solar tracking system for varying the heat flux, whereas the indoor setup uses electric heating elements to vary the heat flux and a low speed wind tunnel blows the ambient air past the device to simulate the outdoor breezes. It was observed that bare plate cooling can achieve a maximum heat flux of 18,125 W/m2 for type A and 31,195 W/m2 for type B at ambient wind speed of 5 m/s while maintaining respective allowable temperature over the hot side of TEG’s. Fin geometry was optimised for the finned block cooling by using the fin length and fin gap optimisation model presented in this paper. It was observed that an optimum finned block cooling arrangement can reach a maximum heat flux of 26,067 W/m2 for type A and 52,251 W/m2 for type B TEG at ambient wind speed of 5 m/s of ambient wind speed. The heat pipe with finned condenser used for cooling can reach 40,375 W/m2 for type A TEG and 76,781 W/m2 for type B TEG.

Ashwin Date; Abhijit Date; Chris Dixon; Randeep Singh; Aliakbar Akbarzadeh

2015-01-01T23:59:59.000Z

170

Design of a biomimetic pectoral fin joint in an artificial fish  

E-Print Network [OSTI]

A biomimetic design of the muscle joint in a pectoral fish fin was produced based on comparisons with four design models. All four design models consisted of a mechanical joint connection and incorporated the functional ...

Peña, Vanessa, 1982-

2004-01-01T23:59:59.000Z

171

Purification of alkali metal nitrates  

DOE Patents [OSTI]

A process is disclosed for removing heavy metal contaminants from impure alkali metal nitrates containing them. The process comprises mixing the impure nitrates with sufficient water to form a concentrated aqueous solution of the impure nitrates, adjusting the pH of the resulting solution to within the range of between about 2 and about 7, adding sufficient reducing agent to react with heavy metal contaminants within said solution, adjusting the pH of the solution containing reducing agent to effect precipitation of heavy metal impurities and separating the solid impurities from the resulting purified aqueous solution of alkali metal nitrates. The resulting purified solution of alkali metal nitrates may be heated to evaporate water therefrom to produce purified molten alkali metal nitrate suitable for use as a heat transfer medium. If desired, the purified molten form may be granulated and cooled to form discrete solid particles of alkali metal nitrates.

Fiorucci, Louis C. (Hamden, CT); Gregory, Kevin M. (Woodridge, IL)

1985-05-14T23:59:59.000Z

172

Corrosion behavior of several metals in ethylene glycol-base heat-transfer fluids under conditions encountered in solar energy systems  

SciTech Connect (OSTI)

The corrosion behavior of aluminum, copper, and iron in inhibited ethylene glycol-ASTM corrosive water solutions was evaluated in a laboratory loop under isothermal and heat-flux conditions for 1000 h at temperatures between 378 and 413/sup 0/K, in static autoclave tests at 450/sup 0/K for 500 h, and by potentiodynamic polarization measurements at temperatures between 298 and 348/sup 0/K. The effect of time, temperature, and ethylene glycol concentration of the heat-transfer fluid on the extent of inhibitor depletion was determined from analyses of the reserve alkalinity, pH, and inhibitor content of the solutions. The performance of an electrochemical sensor as a monitor of fluid quality was also evaluated. A heat flux of 0.4 to 1.0 kW/m/sup 2/ did not have a significant effect on the corrosion behavior of the various materials at temperatures between 378 and 413/sup 0/K. The corrosion rates of aluminum, copper, and iron in the 50 volume percent inhibited ethylene glycol-corrosive water solution decreased as a function of time during the 1000-h test. At 413/sup 0/K, the corrosion rate of copper was considerably higher than that of iron or aluminum at low flow velocity. Significant degradation of the fluid quality, as indicated by the measurement of the pH, reserve alkalinity, and inhibitor concentrations, occurred after several hundred hours at temperatures of approx. 450/sup 0/K.

Zeman, G.J.

1980-01-01T23:59:59.000Z

173

USING LIGA BASED MICROFABRICATION TO IMPROVE OVERALL HEAT TRANSFER EFFICIENCY OF PRESSURIZED WATER REACTOR: I. Effects of Different Micro Pattern on Overall Heat Transfer.  

SciTech Connect (OSTI)

The Pressurized Water Reactors (PWRs in Figure 1) were originally developed for naval propulsion purposes, and then adapted to land-based applications. It has three parts: the reactor coolant system, the steam generator and the condenser. The Steam generator (a yellow area in Figure 1) is a shell and tube heat exchanger with high-pressure primary water passing through the tube side and lower pressure secondary feed water as well as steam passing through the shell side. Therefore, a key issue in increasing the efficiency of heat exchanger is to improve the design of steam generator, which is directly translated into economic benefits. The past research works show that the presence of a pin-fin array in a channel enhances the heat transfer significantly. Hence, using microfabrication techniques, such as LIGA, micro-molding or electroplating, some special microstructures can be fabricated around the tubes in the heat exchanger to increase the heat-exchanging efficiency and reduce the overall size of the heat-exchanger for the given heat transfer rates. In this paper, micro-pin fins of different densities made of SU-8 photoresist are fabricated and studied to evaluate overall heat transfer efficiency. The results show that there is an optimized micro pin-fin configuration that has the best overall heat transfer effects.

Zhang, M.; Ibekwe, S.; Li, G.; Pang, S.S.; and Lian, K.

2006-07-01T23:59:59.000Z

174

The design, construction, and instrumentation of a chamber to study heat, mass, and momentum transfer from humid air to metal under conditions of frosting and free convection  

E-Print Network [OSTI]

It wns decided to use two heating coils, one as a steady input heater and the other as a control heater, From the preceding calculations a control hester twenty feet in length wns installed in the aiF flow along with a steady input heater coil forty... and thermocouple leads until the disks were parallel to and in contact with the teat surfaces. under these conditions the sero point of the scale wss marked. Then while a steel rule was held perpsadicular to the test surface and close to one of the copper disks...

Hutchison, James P

1961-01-01T23:59:59.000Z

175

Heat transfer at the mold-metal interface in permanent mold casting of aluminum alloys project. Quarterly project status report, January 1, 1998--March 31, 1998  

SciTech Connect (OSTI)

There have been numerous developments in the current project over the last three months. The most appropriate geometries for performing the interfacial heat transfer studies have been discussed with both of our Industrial Partners. Both companies have molds which may be available for adaptation to record the thermal history during casting required for determining interfacial heat transfer coefficients. The details of what instrumentation would be the most appropriate remain to be worked out, but the instrumentation would likely include thermocoupling in the mold cavity as well as in the mold wall, as well as pressure sensors in the squeeze casting geometry molds and ultrasonic gap monitoring in the low pressure and gravity fed permanent mold geometry molds. The first advisory committee meeting was held on February 6th, and the steering committee was apprised of the objectives of the program. The capabilities of the Industrial Partners were reviewed, as well as the need for the project to make use of resources from other CMC projects. The second full Advisory Committee Meeting will be held in early May.

Pehlke, R.D.; Hao, Shouwei; Cookson, J.M.

1998-03-31T23:59:59.000Z

176

Microchannel heat sink assembly  

DOE Patents [OSTI]

The present invention provides a microchannel heat sink with a thermal range from cryogenic temperatures to several hundred degrees centigrade. The heat sink can be used with a variety of fluids, such as cryogenic or corrosive fluids, and can be operated at a high pressure. The heat sink comprises a microchannel layer preferably formed of silicon, and a manifold layer preferably formed of glass. The manifold layer comprises an inlet groove and outlet groove which define an inlet manifold and an outlet manifold. The inlet manifold delivers coolant to the inlet section of the microchannels, and the outlet manifold receives coolant from the outlet section of the microchannels. In one embodiment, the manifold layer comprises an inlet hole extending through the manifold layer to the inlet manifold, and an outlet hole extending through the manifold layer to the outlet manifold. Coolant is supplied to the heat sink through a conduit assembly connected to the heat sink. A resilient seal, such as a gasket or an O-ring, is disposed between the conduit and the hole in the heat sink in order to provide a watertight seal. In other embodiments, the conduit assembly may comprise a metal tube which is connected to the heat sink by a soft solder. In still other embodiments, the heat sink may comprise inlet and outlet nipples. The present invention has application in supercomputers, integrated circuits and other electronic devices, and is suitable for cooling materials to superconducting temperatures. 13 figs.

Bonde, W.L.; Contolini, R.J.

1992-03-24T23:59:59.000Z

177

Assessment of adsorber bed designs in waste-heat driven adsorption cooling systems for vehicle air conditioning and refrigeration  

E-Print Network [OSTI]

Assessment of adsorber bed designs in waste-heat driven adsorption cooling systems for vehicle air conditioning Finned tube adsorber bed Specific cooling power Adsorber bed to adsorbent mass ratio a b s t r a c t Adsorber bed design strongly affects the performance of waste-heat driven adsorption cooling systems (ACS

Bahrami, Majid

178

Geothermal Heat Pumps- Heating Mode  

Broader source: Energy.gov [DOE]

In winter, fluid passing through this vertical, closed loop system is warmed by the heat of the earth; this heat is then transferred to the building.

179

LABORATORY I: CONSERVATION OF ENERGY AND HEAT  

E-Print Network [OSTI]

Lab I - 1 LABORATORY I: CONSERVATION OF ENERGY AND HEAT In 1101 labs, you used conservation are in thermal equilibrium · Use the latent heat to determine the internal energy change of a system during conservation of energy, you can then determine the metal's specific heat. However, you know that some energy

Minnesota, University of

180

NREL: Learning - Solar Process Heat  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Process Heat Process Heat Photo of part of one side of a warehouse wall, where a perforated metal exterior skin is spaced about a foot out from the main building wall to form part of the transpired solar collector system. A transpired collector is installed at a FedEx facility in Denver, Colorado. Commercial and industrial buildings may use the same solar technologies-photovoltaics, passive heating, daylighting, and water heating-that are used for residential buildings. These nonresidential buildings can also use solar energy technologies that would be impractical for a home. These technologies include ventilation air preheating, solar process heating, and solar cooling. Space Heating Many large buildings need ventilated air to maintain indoor air quality. In cold climates, heating this air can use large amounts of energy. But a

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Stabilization of Electrocatalytic Metal Nanoparticles at Metal...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Electrocatalytic Metal Nanoparticles at Metal-Metal Oxide-Graphene Triple Junction Points. Stabilization of Electrocatalytic Metal Nanoparticles at Metal-Metal Oxide-Graphene...

182

Linings with optimum heat-emission surfaces for cars receiving and transporting incandescent coke  

SciTech Connect (OSTI)

The least reliable components of the cars which receive and transport incandescent coke are the lining plates. This applies to both the quenching cars used for wet quenching and the hot-coke cars used in the dry cooling process. Technical advances have been described whereby the life of car linings is prolonged by increasing heat emission from the lining plate surfaces. As the heat emission level is enhanced the mean plate temperature is lowered and the lining life thereby prolonged; moreover, the between-servicings period is prolonged. This involves providing fins on the non-working (outer) plate surfaces. The problem of optimizing the size and shape of the fins with reference to heat emission remains unsolved: the requirement is maximum heat emission from plates of a given weight, or conversely minimum plate weight for a given heat emission level. 6 refs., 3 figs.

Kotlyar, B.D.; Pleshkov, P.I.; Gadyatskii, V.G. [and others

1992-12-31T23:59:59.000Z

183

Integrating preconcentrator heat controller  

DOE Patents [OSTI]

A method and apparatus for controlling the electric resistance heating of a metallic chemical preconcentrator screen, for example, used in portable trace explosives detectors. The length of the heating time-period is automatically adjusted to compensate for any changes in the voltage driving the heating current across the screen, for example, due to gradual discharge or aging of a battery. The total deposited energy in the screen is proportional to the integral over time of the square of the voltage drop across the screen. Since the net temperature rise, .DELTA.T.sub.s, of the screen, from beginning to end of the heating pulse, is proportional to the total amount of heat energy deposited in the screen during the heating pulse, then this integral can be calculated in real-time and used to terminate the heating current when a pre-set target value has been reached; thereby providing a consistent and reliable screen temperature rise, .DELTA.T.sub.s, from pulse-to-pulse.

Bouchier, Francis A. (Albuquerque, NM); Arakaki, Lester H. (Edgewood, NM); Varley, Eric S. (Albuquerque, NM)

2007-10-16T23:59:59.000Z

184

Heat Resistance of Electric Arc Coatings Made of Fe–Cr–B–Al Powder Wire  

Science Journals Connector (OSTI)

Electric metallized coatings made of Fe–Cr–B–Al powder wire possess a high heat resistance at 700–800°C at the level ... the base material. To obtain heat-resistant electric metallized coatings of powder wire, it...

V. Pokhmurs'kyi; M. Student; B. Formanek; V. Serivka; Yu. Dz'oba…

2003-11-01T23:59:59.000Z

185

Heat transfer at the mold-metal interface in permanent mold casting of aluminum alloys project. Annual project status report for the period October 1, 1997 to September 30, 1998  

SciTech Connect (OSTI)

In the first year of this three-year project, substantial progress has been achieved. This project on heat transfer coefficients in metal permanent mold casting is being conducted in three areas. They are the theoretical study at the University of Michigan, the experimental investigations of squeeze casting and semi-solid casting at CMI-Tech Center, and the experimental investigation of low pressure permanent mold casting at Amcast Automotive. U-M did an initial geometry which was defined for ProCAST to solve, and then a geometry half the size was defined and solved using the same boundary conditions. A conceptual mold geometry was examined and is represented as an axisymmetric element.Furthermore, the influences of the localized heat transfer coefficients on the casting process were carefully studied. The HTC Evaluator has been proposed and initially developed by the U-M team. The Reference and the Database Modules of the HTC Evaluator have been developed, and extensively tested. A series of technical barriers have been cited and potential solutions have been surveyed. At the CMI-Tech Center, the Kistler direct cavity pressure measurement system has been purchased and tested. The calibrations has been evaluated. The probe is capable of sensing a light finger pressure. The experimental mold has been designed and modified. The experimental mold has been designed and modified. The first experiment is scheduled for October 14, 1998. The geometry of the experimental hockey-puck casting has been given to the U-M team for numerical analysis.

Pehlke, R.D.; Hao, S.W.

1998-09-30T23:59:59.000Z

186

Metal stocks and sustainability  

Science Journals Connector (OSTI)

...1–4). Unlike oil, which is irremediably...relative scarcity (or price) of the material substituted...interior wiring; plumbing, heating, and architectural uses; and...defined in terms of current prices and costs of production; this...cost-effective at current metal prices. Because the real price of copper has remained...

R. B. Gordon; M. Bertram; T. E. Graedel

2006-01-01T23:59:59.000Z

187

Graded pitch electromagnetic pump for thin strip metal casting systems  

DOE Patents [OSTI]

A metal strip casing system is provided with an electromagnetic pump which includes a pair of primary blocks having a graded pole pitch, polyphase ac winding and being arranged on opposite sides of a movable heat sink. A nozzle is provided for depositing liquid metal on the heat sink such that the resulting metal strip and heat sink combination is subjected to a longitudinal electromagnetic field which increases in wavelength in the direction of travel of the heat sink, thereby subjecting the metal and heat sink to a longitudinal force having a magnitude which increases in the direction of travel. 4 figs.

Kuznetsov, S.B.

1986-04-01T23:59:59.000Z

188

Metal Aminoboranes  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Metal Aminoboranes Metal Aminoboranes Metal Aminoboranes Metal aminoboranes of the formula M(NH.sub.2BH.sub.3).sub.n have been synthesized. June 25, 2013 Metal Aminoboranes Metal aminoboranes of the formula M(NH.sub.2BH.sub.3).sub.n have been synthesized. Available for thumbnail of Feynman Center (505) 665-9090 Email Metal Aminoboranes Metal aminoboranes of the formula M(NH.sub.2BH.sub.3).sub.n have been synthesized. Metal aminoboranes are hydrogen storage materials. Metal aminoboranes are also precursors for synthesizing other metal aminoboranes. Metal aminoboranes can be dehydrogenated to form hydrogen and a reaction product. The reaction product can react with hydrogen to form a hydrogen storage material. Metal aminoboranes can be included in a kit. U.S. Patent No.: 7,713,506 (DOE S-112,798)

189

Interpolated versus Polytopic Gain Scheduling Control Laws for Fin/Rudder Roll Stabilisation of Ships  

E-Print Network [OSTI]

Interpolated versus Polytopic Gain Scheduling Control Laws for Fin/Rudder Roll Stabilisation be done through the use of gain-scheduling (GS) control law. In this study, a GS-control law is obtained and a desired stabilisation quality factor. Gain scheduling is a way to obtain parameter dependent controllers

Paris-Sud XI, Université de

190

A GAIN SCHEDULED CONTROL LAW FOR FIN/RUDDER ROLL STABILISATION OF SHIPS  

E-Print Network [OSTI]

A GAIN SCHEDULED CONTROL LAW FOR FIN/RUDDER ROLL STABILISATION OF SHIPS Hervé Tanguy , Guy Lebret leads to a gain-scheduled control law. The synthesis is based on multi-objective optimisation stabilisation; H control; Gain Scheduled Control; polytopic representation; LMI. 1. INTRODUCTION A major

Paris-Sud XI, Université de

191

Design, fabrication and analysis of a body-caudal fin propulsion system for a microrobotic fish  

E-Print Network [OSTI]

Design, fabrication and analysis of a body-caudal fin propulsion system for a microrobotic fish Kyu and fabrica- tion of a centimeter-scale propulsion system for a robotic fish. The key to the design are customized to provide the necessary work output for the microrobotic fish. The flexure joints, electrical

Wood, Robert

192

FY 2013 AgencY FinAnciAl RepoRt www.nasa.gov  

E-Print Network [OSTI]

FY 2013 AgencY FinAnciAl RepoRt www.nasa.gov National Aeronautics and Space Administration #12;Front Cover: Outside Front Main Image: Artist concept of planets space. (Credit: NASA) Outside Front of extrave- hicular activity (EVA) as work continues on the International Space Station. (Credit: NASA

Waliser, Duane E.

193

Liquid metal cooled nuclear reactor plant system  

DOE Patents [OSTI]

A liquid metal cooled nuclear reactor having a passive cooling system for removing residual heat resulting for fuel decay during reactor shutdown, or heat produced during a mishap. The reactor system is enhanced with sealing means for excluding external air from contact with the liquid metal coolant leaking from the reactor vessel during an accident. The invention also includes a silo structure which resists attack by leaking liquid metal coolant, and an added unique cooling means.

Hunsbedt, Anstein (Los Gatos, CA); Boardman, Charles E. (Saratoga, CA)

1993-01-01T23:59:59.000Z

194

Susanville District Heating District Heating Low Temperature...  

Open Energy Info (EERE)

Susanville District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Susanville District Heating District Heating Low Temperature...

195

Theory of bonding of transition metals to nontransition metals  

Science Journals Connector (OSTI)

We present a theory of the chemical bond in compounds consisting of both transition metals and nontransition metals. Chemical trends in the bonding properties are established by directly comparing the total energies of a large number of such compounds with the total energies of their constituents. These chemical trends are analyzed in terms of the s-, p-, and d-like state densities of the compounds and the constituents. Rather different types of bonding are shown to result when the atomic s and p levels of the nontransition metal lie above, below, and near the energy of the transition-metal d level. The heat of compound formation is shown to result from a competition between two simple physical effects: (1) the weakening of the transition-metal bonds by the lattice dilatation required for the accommodation of the nontransition metal, and (2) the increased bonding which results from the occupation of the bonding members of the hybrid states formed from the interaction between the transition-metal d states and the s-p states on the nontransition metal. Our theoretical values for the heats of formation of these compounds are generally similar to those given by Miedema's empirical formula. Distinctive aspects of the variation of the heat of formation with the number of valence electrons reveal, however, that the microscopic picture on which the empirical formula is based is quite different from that given by our self-consistent energy-band theory.

C. D. Gelatt; Jr.; A. R. Williams; V. L. Moruzzi

1983-02-15T23:59:59.000Z

196

Chemical heat pump project: Final report  

SciTech Connect (OSTI)

Solid/vapor working media can be used as working fluids in industrial heat pumps for heat amplifier and temperature amplifier concepts. This report describes the theoretical investigation of candidate solid/vapor fluids and the development of single and multi-stage heat pump cycles. Ammoniated complex compounds, hydrated complex compounds, metal carbonate-metal oxide media, and metal hydrides were investigated. A preliminary computer model was developed to predict the performance characteristics of a single-stage complex compound temperature amplifier and to outline the limitations of such concepts. A preliminary first cost calculation was performed in order to determine the economical feasibility of solid/vapor industrial heat pumps in comparison to boilers nd state-of-the-art heat pump equipment.

Not Available

1985-01-01T23:59:59.000Z

197

Nanoparticle enhanced ionic liquid heat transfer fluids  

DOE Patents [OSTI]

A heat transfer fluid created from nanoparticles that are dispersed into an ionic liquid is provided. Small volumes of nanoparticles are created from e.g., metals or metal oxides and/or alloys of such materials are dispersed into ionic liquids to create a heat transfer fluid. The nanoparticles can be dispersed directly into the ionic liquid during nanoparticle formation or the nanoparticles can be formed and then, in a subsequent step, dispersed into the ionic liquid using e.g., agitation.

Fox, Elise B.; Visser, Ann E.; Bridges, Nicholas J.; Gray, Joshua R.; Garcia-Diaz, Brenda L.

2014-08-12T23:59:59.000Z

198

Experimental and numerical heat transfer analysis of a V-cavity absorber for linear parabolic trough solar collector  

Science Journals Connector (OSTI)

Abstract In the present study, a V-cavity absorber with rectangular fins that can be used in the linear parabolic trough collector (PTC) system was proposed and investigated both theoretically and experimentally. The optical performance of the absorber was studied by means of Monte-Carlo ray-tracing (MCRT) method. An energy balance model and a more detailed three-dimensional numerical model were developed to analyze the flow and heat transfer characteristics. Moreover, an experimental setup was built to validate the theoretical analysis. A reasonable agreement between the theoretical and experimental results was achieved, which proves the feasibility and reliability of the models. The results show that the sunlight could be reflected repeatedly by the triangle shape and nearly no sunlight escapes. The absorber with rectangular fins has a better heat transfer performance with higher outlet temperature of heat transfer fluid (HTF), lower temperature of heating surface and lower heat loss than those of absorber without fins. The effects of heat flux distribution, mass flow rate and direct normal irradiance on the heat transfer performance were further discussed. In addition, the variations of the heat transfer coefficient along z axial direction with different mass flow rates were also calculated based on the numerical results.

X. Xiao; P. Zhang; D.D. Shao; M. Li

2014-01-01T23:59:59.000Z

199

Production of glass or glass-ceramic to metal seals with the application of pressure  

DOE Patents [OSTI]

In a process for preparing a glass or glass-ceramic to metal seal comprising contacting the glass with the metal and heat-treating the glass and metal under conditions whereby the glass to metal seal is effected and, optionally, the glass is converted to a glass-ceramic, an improvement comprises carrying out the heat-treating step using hot isostatic pressing.

Kelly, Michael D. (West Alexandria, OH); Kramer, Daniel P. (Dayton, OH)

1987-11-10T23:59:59.000Z

200

Production of glass or glass-ceramic to metal seals with the application of pressure  

DOE Patents [OSTI]

In a process for preparing a glass or glass-ceramic to metal seal comprising contacting the glass with the metal and heat-treating the glass and metal under conditions whereby the glass to metal seal is effected and, optionally, the glass is converted to a glass-ceramic, an improvement comprises carrying out the heat-treating step using hot isostatic pressing.

Kelly, M.D.; Kramer, D.P.

1985-01-04T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

La guerra del fin del mundo: historia e invencion en una novela historica  

E-Print Network [OSTI]

or inexplicable elements in human reality, and which finds the novel a vehicle for a more complete understanding of that reality as represented by histor- ical data. The text of this thesis is written in Spanish. iv INDICE DE MATERIAS CAPITULO I... ' INTRODUCCION Pagina Historia e invencion en la novela historica Historia e invencion: El concepto de Verges Llosa y algunos contemporaneos suyos La realidad historica y la invencion artistica en La uerra del fin del mundo 12 II EL ACONTECIHIENTO...

Loeffler, Lisa Bowe

2012-06-07T23:59:59.000Z

202

Effect of steam on supported metal catalysts  

SciTech Connect (OSTI)

In order to examine the effect of steam on supported metal catalysts, model supported metal catalysts of Ni, Co, or Fe on alumina have been heated in steam at 700/sup 0/C. The transmission electron micrographs show that for all these metals, patches of film extend from the crystallites. Prolonged heating results in the disappearance of the patches which probably spread as a contiguous film over the entire surface of the substrate. The degree of spreading is in the order: C0 > Ni > Fe. On subsequent heating in H/sub 2/, small crystallites were generated, probably via the rupture of the contiguous film. The contraction of the patches of film bridging two or several particles caused the coalescence of the latter. This subsequent heating in H/sub 2/ favors redispersion only when the heating time is sufficiently short. Prolonged heating in H/sub 2/ leads to the disappearance of the small particles.

Ruckenstein, E.; Hu, X.D.

1986-07-01T23:59:59.000Z

203

Fuel Saving Ideas for Metal and Ceramic Processing  

E-Print Network [OSTI]

An easy method is presented for analyzing sources of heat loss from industrial processing furnaces, kilns, and ovens; and thus for recognizing opportunities for fuel saving. This will relate to melting, heat treating and hot forming of metals...

Reed, R. J.

1982-01-01T23:59:59.000Z

204

Heat Stroke  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

stress, from exertion or hot environments, places stress, from exertion or hot environments, places workers at risk for illnesses such as heat stroke, heat exhaustion, or heat cramps. Heat Stroke A condition that occurs when the body becomes unable to control its temperature, and can cause death or permanent disability. Symptoms â–  High body temperature â–  Confusion â–  Loss of coordination â–  Hot, dry skin or profuse sweating â–  Throbbing headache â–  Seizures, coma First Aid â–  Request immediate medical assistance. â–  Move the worker to a cool, shaded area. â–  Remove excess clothing and apply cool water to their body. Heat Exhaustion The body's response to an excessive loss of water and salt, usually through sweating. Symptoms â–  Rapid heart beat â–  Heavy sweating â–  Extreme weakness or fatigue â– 

205

Computational Analysis of Thermo-Fluidic Characteristics of a Carbon Nano-Fin  

E-Print Network [OSTI]

of electronic devices. Experiments on carbon nanotube coated heater surfaces have shown heat transfer enhancement of 60 percent. In addition, silicon nanotubes etched on the silicon substrates have shown heat flux enhancement by as much as 120 percent. The heat...

Singh, Navdeep

2011-02-22T23:59:59.000Z

206

Electric Adsorption Heat Pump for Electric Vehicles: Electric-Powered Adsorption Heat Pump for Electric Vehicles  

SciTech Connect (OSTI)

HEATS Project: PNNL is developing a new class of advanced nanomaterial called an electrical metal organic framework (EMOF) for EV heating and cooling systems. The EMOF would function similar to a conventional heat pump, which circulates heat or cold to the cabin as needed. However, by directly controlling the EMOF's properties with electricity, the PNNL design is expected to use much less energy than traditional heating and cooling systems. The EMOF-based heat pumps would be light, compact, efficient, and run using virtually no moving parts.

None

2011-11-21T23:59:59.000Z

207

Metal Buildings - 2014 BTO Peer Review | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

the project addresses infiltration issues that can reduce heating, ventilation, and air conditioning (HVAC) building source usage for single-story metal buildings in...

208

Metal to ceramic sealed joint  

DOE Patents [OSTI]

A metal to ceramic sealed joint which can withstand wide variations in temperature and maintain a good seal is provided for use in a device adapted to withstand thermal cycling from about 20 to about 1000 degrees C. The sealed joint includes a metal member, a ceramic member having an end portion, and an active metal braze forming a joint to seal the metal member to the ceramic member. The joint is positioned remote from the end portion of the ceramic member to avoid stresses at the ends or edges of the ceramic member. The sealed joint is particularly suited for use to form sealed metal to ceramic joints in a thermoelectric generator such as a sodium heat engine where a solid ceramic electrolyte is joined to metal parts in the system.

Lasecki, John V. (Livonia, MI); Novak, Robert F. (Farmington Hills, MI); McBride, James R. (Ypsilanti, MI)

1991-01-01T23:59:59.000Z

209

Metal to ceramic sealed joint  

DOE Patents [OSTI]

A metal to ceramic sealed joint which can withstand wide variations in temperature and maintain a good seal is provided for use in a device adapted to withstand thermal cycling from about 20 to about 1000 degrees C. The sealed joint includes a metal member, a ceramic member having an end portion, and an active metal braze forming a joint to seal the metal member to the ceramic member. The joint is positioned remote from the end portion of the ceramic member to avoid stresses at the ends or edges of the ceramic member. The sealed joint is particularly suited for use to form sealed metal to ceramic joints in a thermoelectric generator such as a sodium heat engine where a solid ceramic electrolyte is joined to metal parts in the system. 11 figures.

Lasecki, J.V.; Novak, R.F.; McBride, J.R.

1991-08-27T23:59:59.000Z

210

Development of Monitoring Control and Fuzzy Control Test of Finned-Tube Heat-Exchanger Test-Board  

E-Print Network [OSTI]

of computer control system PCI1756 controlled quantity fuzzy control algorithem error stated value measured value ADAM4018 Thermocouple switching value ADAM3000 ports board COM IDO0..00/30 DGND DC AC controllable siliceous relay electric heater 5~40V Fig.3...

Chen, Y.; Zhang, J.; Zhang, B.; Gao, F.

2006-01-01T23:59:59.000Z

211

Heat collector  

DOE Patents [OSTI]

A heat collector and method suitable for efficiently and cheaply collecting solar and other thermal energy are provided. The collector employs a heat pipe in a gravity-assist mode and is not evacuated. The collector has many advantages, some of which include ease of assembly, reduced structural stresses on the heat pipe enclosure, and a low total materials cost requirement. Natural convective forces drive the collector, which after startup operates entirely passively due in part to differences in molecular weights of gaseous components within the collector.

Merrigan, Michael A. (Santa Cruz, NM)

1984-01-01T23:59:59.000Z

212

Heat collector  

DOE Patents [OSTI]

A heat collector and method suitable for efficiently and cheaply collecting solar and other thermal energy are provided. The collector employs a heat pipe in a gravity-assist mode and is not evacuated. The collector has many advantages, some of which include ease of assembly, reduced structural stresses on the heat pipe enclosure, and a low total materials cost requirement. Natural convective forces drive the collector, which after startup operates entirely passively due in part to differences in molecular weights of gaseous components within the collector.

Merrigan, M.A.

1981-06-29T23:59:59.000Z

213

Metal inks  

DOE Patents [OSTI]

Self-reducing metal inks and systems and methods for producing and using the same are disclosed. In an exemplary embodiment, a method may comprise selecting metal-organic (MO) precursor, selecting a reducing agent, and dissolving the MO precursor and the reducing agent in an organic solvent to produce a metal ink that remains in a liquid phase at room temperature. Metal inks, including self-reducing and fire-through metal inks, are also disclosed, as are various applications of the metal inks.

Ginley, David S; Curtis, Calvin J; Miedaner, Alex; van Hest, Marinus Franciscus Antonius Maria; Kaydanova, Tatiana

2014-02-04T23:59:59.000Z

214

Method of nitriding refractory metal articles  

DOE Patents [OSTI]

A method of nitriding a refractory-nitride forming metal or metalloid articles and composite articles. A consolidated metal or metalloid article or composite is placed inside a microwave oven and nitrogen containing gas is introduced into the microwave oven. The metal or metalloid article or composite is heated to a temperature sufficient to react the metal or metalloid with the nitrogen by applying a microwave energy within the microwave oven. The metal or metalloid article or composite is maintained at that temperature for a period of time sufficient to convert the article of metal or metalloid or composite to an article or composite of refractory nitride. In addition, a method of applying a coating, such as a coating of an oxide, a carbide, or a carbo-nitride, to an article of metal or metalloid by microwave heating.

Tiegs, Terry N. (Lenoir City, TN); Holcombe, Cressie E. (Knoxville, TN); Dykes, Norman L. (Oak Ridge, TN); Omatete, Ogbemi O. (Lagos, NG); Young, Albert C. (Flushing, NY)

1994-01-01T23:59:59.000Z

215

Method of nitriding refractory metal articles  

DOE Patents [OSTI]

A method of nitriding a refractory-nitride forming metal or metalloid articles and composite articles. A consolidated metal or metalloid article or composite is placed inside a microwave oven and nitrogen containing gas is introduced into the microwave oven. The metal or metalloid article or composite is heated to a temperature sufficient to react the metal or metalloid with the nitrogen by applying a microwave energy within the microwave oven. The metal or metalloid article or composite is maintained at that temperature for a period of time sufficient to convert the article of metal or metalloid or composite to an article or composite of refractory nitride. In addition, a method of applying a coating, such as a coating of an oxide, a carbide, or a carbo-nitride, to an article of metal or metalloid by microwave heating.

Tiegs, T.N.; Holcombe, C.E.; Dykes, N.L.; Omatete, O.O.; Young, A.C.

1994-03-15T23:59:59.000Z

216

Susceptor heating device for electron beam brazing  

DOE Patents [OSTI]

A brazing device and method are provided which locally apply a controlled amount of heat to a selected area, within a vacuum. The device brazes two components together with a brazing metal. A susceptor plate is placed in thermal contact with one of the components. A serrated pedestal supports the susceptor plate. When the pedestal and susceptor plate are in place, an electron gun irradiates an electron beam at the susceptor plate such that the susceptor plate is sufficiently heated to transfer heat through the one component and melt the brazing metal.

Antieau, Susan M. (Pittsburgh, PA); Johnson, Robert G. R. (Trafford, PA)

1999-01-01T23:59:59.000Z

217

Metal Oxides  

Science Journals Connector (OSTI)

Metal oxides are the class of materials having the widest application in gas sensors. This chapter presents information related to the application of various metal oxides in gas sensors designed on different p...

Ghenadii Korotcenkov

2013-01-01T23:59:59.000Z

218

Method for the generation of variable density metal vapors which bypasses the liquidus phase  

DOE Patents [OSTI]

The present invention provides a method for producing a metal vapor that includes the steps of combining a metal and graphite in a vessel to form a mixture; heating the mixture to a first temperature in an argon gas atmosphere to form a metal carbide; maintaining the first temperature for a period of time; heating the metal carbide to a second temperature to form a metal vapor; withdrawing the metal vapor and the argon gas from the vessel; and separating the metal vapor from the argon gas. Metal vapors made using this method can be used to produce uniform powders of the metal oxide that have narrow size distribution and high purity.

Kunnmann, Walter (Stony Brook, NY); Larese, John Z. (Rocky Point, NY)

2001-01-01T23:59:59.000Z

219

Silicone metalization  

DOE Patents [OSTI]

A system for providing metal features on silicone comprising providing a silicone layer on a matrix and providing a metal layer on the silicone layer. An electronic apparatus can be produced by the system. The electronic apparatus comprises a silicone body and metal features on the silicone body that provide an electronic device.

Maghribi, Mariam N. (Livermore, CA); Krulevitch, Peter (Pleasanton, CA); Hamilton, Julie (Tracy, CA)

2006-12-05T23:59:59.000Z

220

Electron Dynamics in Metallic Nanoparticles M. Aeschlimann  

E-Print Network [OSTI]

nanoparticles are discussed in the light of the results of line width measurements and femtosecond pump...............................................................................................................3 II. ADSORPTION OF LIGHT IN METALLIC NANOPARTICLES...................................4 A. General...............................................18 C. Heat transfer between the nanoparticles and the support

Bauer, Michael

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

JOURNAL DE PHYSIQUE Colloque C5, supplkment au no 5, Tome 40, Mai 1979, page C5-63 Heat capacity of rare earth metals near the melting point and the vacancy  

E-Print Network [OSTI]

of rare earth metals near the melting point and the vacancy mechanism of melting T. Gorecki (*) Max. -The vacancy mechanism of the melting process is utilized as a starting point for deriving the formula point and changes of the same properties of metals due to the creation of vacancies has been

Paris-Sud XI, Université de

222

Heating System Specification Specification of Heating System  

E-Print Network [OSTI]

Appendix A Heating System Specification /* Specification of Heating System (loosely based */ requestHeat : Room ­? bool; 306 #12; APPENDIX A. HEATING SYSTEM SPECIFICATION 307 /* user inputs */ livingPattern : Room ­? behaviour; setTemp : Room ­? num; heatSwitchOn, heatSwitchOff, userReset : simple

Day, Nancy

223

Heat pipes for use in a magnetic field  

DOE Patents [OSTI]

A heat pipe configuration for use in a magnetic field environment of a fusion reactor is disclosed. Heat pipes for operation in a magnetic field when liquid metal working fluids are used are optimized by flattening of the heat pipes having an unobstructed annulus which significantly reduces the adverse side region effect of the prior known cylindrically configured heat pipes. The flattened heat pipes operating in a magnetic field can remove 2--3 times the heat as a cylindrical heat pipe of the same cross sectional area. 4 figs.

Werner, R.W.; Hoffman, M.A.

1983-07-19T23:59:59.000Z

224

Decisiones de la máscara neutra: Dramaturgia femenina y fin de siglo en América Latina  

E-Print Network [OSTI]

finesecular en América Latina siempre desde una evaluación de realidades en movimiento. Enajenación discursiva y resistencia de la representación en el fin de siglo El siglo XX se despide con el conocido agotamiento en los modos de representación de... inmediata para una nueva formulación del signo.2 La inflación de materiales se agrava en las postrimerías del XX para cubrir el vacío o saturar el espacio con lo que Kermode llamaría "the sense of an ending." De alguna forma, - y esto va a tener una gran...

Martí nez de Olcoz, Nieves

1998-04-01T23:59:59.000Z

225

Fabric composite heat pipe technology development  

SciTech Connect (OSTI)

Testing has been performed on a variety of fabric composite technology feasibility issues. These include an evaluation of the effective radiation heat transfer rate from a heated metallic surface covered by a ceramic fabric with the intent of determining the effective emissivity'' of the combination of materials, studies of the wicking properties of ceramic fabrics, and the construction of fabric composite heat pipes to test their working properties under both steady state and transient conditions. Results of these experiments shown that fabric composite combinations have greatly enhanced effective emissivities'' resulting from the increases surface area of the fabric, ceramic fabrics can work very well as the wick for heat pipes, ceramic fabric heat pipes have been demonstrated to operate under typical space conditions, and large mass reductions are possible by using fabric composite heat pipes for heat rejection radiator systems.

Klein, A.C.; Gulshan-Ara, Z.; Kiestler, W.; Snuggerud, R.; Marks, T.S. (Department of Nuclear Engineering, Oregon State University, Corvallis, Oregon 97331 (United States))

1993-01-10T23:59:59.000Z

226

Enhancement of pool boiling heat transfer with electrohydrodynamics and its fundamental study  

E-Print Network [OSTI]

, and 10kV. To conduct this study, an existing low pressure pool boiling apparatus was modified and another high pressure apparatus was designed and built. The fluids were tested on the smooth tube at operating temperatures of 4'C and 20'C, and 19 fins... TWl Tvvo Heat flux of EHD enhancement of boiling (W/m ) Total heat flux with EHD at 10kV (W/m ) Total heat flux with no EHD (W/m ) Minimum cavity mouth radius (m) Rayleigh number Fluid temperature ('C) Pool Saturation temperature ('C) Tube...

Raghupathi, Sri Laxmi Priya

2012-06-07T23:59:59.000Z

227

Fin whale song characteristics recorded on ocean bottom seismometers in the Northeast Pacific Ocean  

Science Journals Connector (OSTI)

Fin whales produce low frequency sequences of vocalizations that can be detected opportunistically on ocean bottom seismometers (OBSs). Using an automatic detection algorithm we have analyzed fin whale calls recorded on OBSs in the Northeast Pacific Ocean over broad spatial and temporal scales. The Cascadia Initiative experiment consists of 70 OBSs deployed for a total of four years (2011–2015). It extends from Vancouver Island to Cape Mendocino and several hundred kilometers offshore. Additional OBS data that overlap spatially with the northern portion of the Cascadia Initiative instruments are available from the Neptune Canada cabled observatory which has been online since 2009 and from standalone deployments between 2003 and 2006. With this study we examine call characteristics and seasonal call counts for patterns that might indicate migratory movements or distinct acoustic populations. Both frequency and inter-pulse interval (IPI) are automatically extracted for each detected call and seasonal and inter-annual calling patterns are examined using daily binned call count histograms. Preliminary analysis of a subset of Cascadia Initiative data from 2011 to 2013 shows a dominant sequence of alternating classic and backbeat calls at center frequencies of 20 and 18.5 Hz respectively and preceding IPIs of 16 and 18 s respectively.

2014-01-01T23:59:59.000Z

228

Molten metal holder furnace and casting system incorporating the molten metal holder furnace  

DOE Patents [OSTI]

A bottom heated holder furnace (12) for containing a supply of molten metal includes a storage vessel (30) having sidewalls (32) and a bottom wall (34) defining a molten metal receiving chamber (36). A furnace insulating layer (42) lines the molten metal receiving chamber (36). A thermally conductive heat exchanger block (54) is located at the bottom of the molten metal receiving chamber (36) for heating the supply of molten metal. The heat exchanger block (54) includes a bottom face (65), side faces (66), and a top face (67). The heat exchanger block (54) includes a plurality of electrical heaters (70) extending therein and projecting outward from at least one of the faces of the heat exchanger block (54), and further extending through the furnace insulating layer (42) and one of the sidewalls (32) of the storage vessel (30) for connection to a source of electrical power. A sealing layer (50) covers the bottom face (65) and side faces (66) of the heat exchanger block (54) such that the heat exchanger block (54) is substantially separated from contact with the furnace insulating layer (42).

Kinosz, Michael J. (Apollo, PA); Meyer, Thomas N. (Murrysville, PA)

2003-02-11T23:59:59.000Z

229

Method and apparatus for dissociating metals from metal compounds extracted into supercritical fluids  

DOE Patents [OSTI]

A method for dissociating metal-ligand complexes in a supercritical fluid by treating the metal-ligand complex with heat and/or reducing or oxidizing agents is described. Once the metal-ligand complex is dissociated, the resulting metal and/or metal oxide form fine particles of substantially uniform size. In preferred embodiments, the solvent is supercritical carbon dioxide and the ligand is a .beta.-diketone such as hexafluoroacetylacetone or dibutyldiacetate. In other preferred embodiments, the metals in the metal-ligand complex are copper, silver, gold, tungsten, titanium, tantalum, tin, or mixtures thereof. In preferred embodiments, the reducing agent is hydrogen. The method provides an efficient process for dissociating metal-ligand complexes and produces easily-collected metal particles free from hydrocarbon solvent impurities. The ligand and the supercritical fluid can be regenerated to provide an economic, efficient process.

Wai, Chien M. (Moscow, ID); Hunt, Fred H. (Moscow, ID); Smart, Neil G. (Workington, GB); Lin, Yuehe (Richland, WA)

2000-01-01T23:59:59.000Z

230

ITP Metal Casting: Advanced Melting Technologies: Energy Saving Concepts and Opportunities for the Metal Casting Industry  

Broader source: Energy.gov [DOE]

The study examines current and emerging melting technologies and discusses their technical barriers to scale-up issues and research needed to advance these technologies, improving melting efficiency, lowering metal transfer heat loss, and reducing scrap.

231

Heat transfer and pressure drop for air flow through enhanced passages  

SciTech Connect (OSTI)

An extensive experimental investigation was carried out to determine the pressure drop and heat transfer characteristics for laminar, transitional and turbulent flow of air through a smooth passage and twenty-three enhanced passages. The internal surfaces of all enhanced passages had spirally shaped geometries; these included fluted, finned/ribbed and indented surfaces. The Reynolds number (Re) was varied between 400 and 50000. The effect of heat transfer (wall cooling or fluid heating) on pressure drop is most significant within the transition region; the recorded pressure drop with heat transfer is much higher than that without heat transfer. The magnitude of this effect depends markedly on the average surface temperature and, to a lesser extent, on the geometric characteristics of the enhanced surfaces. When the pressure drop data are reduced as values of the Fanning friction factor(f), the results are about the same with and without heat transfer for turbulent flow, with moderate differences in the laminar and transition regions.

Obot, N.T.; Esen, E.B.

1992-06-01T23:59:59.000Z

232

Heat transfer and pressure drop for air flow through enhanced passages. Final report  

SciTech Connect (OSTI)

An extensive experimental investigation was carried out to determine the pressure drop and heat transfer characteristics for laminar, transitional and turbulent flow of air through a smooth passage and twenty-three enhanced passages. The internal surfaces of all enhanced passages had spirally shaped geometries; these included fluted, finned/ribbed and indented surfaces. The Reynolds number (Re) was varied between 400 and 50000. The effect of heat transfer (wall cooling or fluid heating) on pressure drop is most significant within the transition region; the recorded pressure drop with heat transfer is much higher than that without heat transfer. The magnitude of this effect depends markedly on the average surface temperature and, to a lesser extent, on the geometric characteristics of the enhanced surfaces. When the pressure drop data are reduced as values of the Fanning friction factor(f), the results are about the same with and without heat transfer for turbulent flow, with moderate differences in the laminar and transition regions.

Obot, N.T.; Esen, E.B.

1992-06-01T23:59:59.000Z

233

Geothermal district heating systems  

SciTech Connect (OSTI)

Ten district heating demonstration projects and their present status are described. The projects are Klamath County YMCA, Susanville District Heating, Klamath Falls District Heating, Reno Salem Plaza Condominium, El Centro Community Center Heating/Cooling, Haakon School and Business District Heating, St. Mary's Hospital, Diamond Ring Ranch, Pagosa Springs District Heating, and Boise District Heating.

Budney, G.S.; Childs, F.

1982-01-01T23:59:59.000Z

234

Chemical vapor deposition of group IIIB metals  

DOE Patents [OSTI]

Coatings of Group IIIB metals and compounds thereof are formed by chemical vapor deposition, in which a heat decomposable organometallic compound of the formula given in the patent where M is a Group IIIB metal, such as lanthanum or yttrium and R is a lower alkyl or alkenyl radical containing from 2 to about 6 carbon atoms, with a heated substrate which is above the decomposition temperature of the organometallic compound. The pure metal is obtained when the compound of the formula 1 is the sole heat decomposable compound present and deposition is carried out under nonoxidizing conditions. Intermetallic compounds such as lanthanum telluride can be deposited from a lanthanum compound of formula 1 and a heat decomposable tellurium compound under nonoxidizing conditions.

Erbil, A.

1989-11-21T23:59:59.000Z

235

Heat Transfer Enhancement in Rectangular Channel with Compound Cooling Techniques  

E-Print Network [OSTI]

. The trailing edge is typically cooled by pin-fins or dimpled surfaces and the mid-chord section is normally cooled by serpentine rib-roughened coolant passages. Jet impingement methods have also been used in the mid-chord section of the blade as well... induced by the ribs that cause the flow to separate and reattach itself. In terms of rib roughen surface configurations, many studies have been performed to determine which alignment of the ribs with respect to the flow produces the highest heat...

Krad, Belal

2013-11-27T23:59:59.000Z

236

Water and Space Heating Heat Pumps  

E-Print Network [OSTI]

This paper discusses the design and operation of the Trane Weathertron III Heat Pump Water Heating System and includes a comparison of features and performance to other domestic water heating systems. Domestic water is generally provided through...

Kessler, A. F.

1985-01-01T23:59:59.000Z

237

Materials Selection Considerations for Thermal Process Equipment: A BestPractices Process Heating Technical Brief  

Broader source: Energy.gov [DOE]

This technical brief is a guide to selecting high-temperature metallic materials for use in process heating applications such as burners, electrical heating elements, material handling, load support, and heater tubes, etc.

238

Development of a single-family absorption chiller for use in a solar heating and cooling system. Phase III, final report. Volume II  

SciTech Connect (OSTI)

The appendices provide supporting information on: properties of a chemical system for solar fired, air-cooled absorption equipment, air-side performance of a one-inch tube, absorber plate-fin coil, listings of the programs used for simulation and data reduction, and evaluation of the Carrier 3-ton chiller in an integrated heating and cooling system. (LEW)

Reimann, R.C.; Biermann, W.J.

1984-10-01T23:59:59.000Z

239

Laser Heat Treatment [Laser Applications Laboratory] - Nuclear Engineering  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Heat Treatment Heat Treatment Capabilities Engineering Experimentation Reactor Safety Experimentation Aerosol Experiments System Components Laser Applications Overview Laser Oil & Gas Well Drilling Laser Heat Treatment Laser Welding of Metals On-line Monitoring Laser Beam Delivery Laser Glazing of Railroad Rails High Power Laser Beam Delivery Decontamination and Decommissioning Refractory Alloy Welding Robots Applications Other Facilities Other Capabilities Work with Argonne Contact us For Employees Site Map Help Join us on Facebook Follow us on Twitter NE on Flickr Laser Applications Laboratory Laser Heat Treatment Project description: Optimization of laser beam heat treatment. Category: Project with industrial partner (Caterpillar and USCAR) Bookmark and Share Heat treatment optics

240

Heat Transfer across the Interface between Nanoscale Solids and Gas  

Science Journals Connector (OSTI)

(4-7) Relative to heat transferred via solid–solid interfaces, heat dissipation from the active device region to the gas environment is usually negligible. ... Long VO2 NWs were cantilevered from a substrate and were locally heated using a focused laser, allowing the laser-heating induced phase transition and the resultant domain structures along the NW to be optically imaged. ... By imaging the laser-heating induced metal–insulator phase transition along single, free-standing VO2 NWs, we determined the heat transfer coefficient between the NW and the gas environment over a wide range of pressure and down to the submicrometer scale. ...

Chun Cheng; Wen Fan; Jinbo Cao; Sang-Gil Ryu; Jie Ji; Costas P. Grigoropoulos; Junqiao Wu

2011-11-09T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Evaluation of fluid bed heat exchanger optimization parameters. Final report  

SciTech Connect (OSTI)

Uncertainty in the relationship of specific bed material properties to gas-side heat transfer in fluidized beds has inhibited the search for optimum bed materials and has led to over-conservative assumptions in the design of fluid bed heat exchangers. An experimental program was carried out to isolate the effects of particle density, thermal conductivity, and heat capacitance upon fluid bed heat transfer. A total of 31 tests were run with 18 different bed material loads on 12 material types; particle size variations were tested on several material types. The conceptual design of a fluidized bed evaporator unit was completed for a diesel exhaust heat recovery system. The evaporator heat transfer surface area was substantially reduced while the physical dimensions of the unit increased. Despite the overall increase in unit size, the overall cost was reduced. A study of relative economics associated with bed material selection was conducted. For the fluidized bed evaporator, it was found that zircon sand was the best choice among materials tested in this program, and that the selection of bed material substantially influences the overall system costs. The optimized fluid bed heat exchanger has an estimated cost 19% below a fin augmented tubular heat exchanger; 31% below a commercial design fluid bed heat exchanger; and 50% below a conventional plain tube heat exchanger. The comparisons being made for a 9.6 x 10/sup 6/ Btu/h waste heat boiler. The fluidized bed approach potentially has other advantages such as resistance to fouling. It is recommended that a study be conducted to develop a systematic selection of bed materials for fluidized bed heat exchanger applications, based upon findings of the study reported herein.

Not Available

1980-03-01T23:59:59.000Z

242

Control Dewar Subcooler Heat Exchanger Calculations  

SciTech Connect (OSTI)

The calculations done to size the control dewar subcooler were done to obtain a sufficient subcooler size based on some conservative assumptions. The final subcooler design proposed in the design report will work even better because (1) It has more tubing length, and (2) will have already subcooled liquid at the inlet due to the transfer line design. The subcooler design described in the 'Design Report of the 2 Tesla Superconducting Solenoid for the Fermilab D0 Detector Upgrade' is the final design proposed. A short description of this design follows. The subcooler is constructed of 0.50-inch OD copper tubing with 1.0-inch diameter fins. It has ten and one half spirals at a 11.375-inch centerline diameter to provide 31 feet of tubing length. The liquid helium supply for the solenoid flows through the subcooler and then is expanded through a J-T valve. The subcooler spirals are immersed in the return two phase helium process stream. The return stream is directed over the finned tubing by an annulus created by a 10-inch pipe inside a 12-inch pipe. The transfer line from the refrigerator to the control dewar is constructed such that the liquid helium supply tube is in the refrigerator return stream, thereby subcooling the liquid up to the point where the u-tubes connect the transfer line to the control dewar. The subcooler within the control dewar will remove the heat picked up in the helium supply u-tube/bayonets. The attached subcooler/heat exchanger calculations were done neglecting any subcooling in the transfer line. All heat picked up in the transfer line from the refrigerator storage dewar to the control dewar is absorbed by the supply stream. The subcooler was sized such that the two phase supply fluid is subcooled at 1.7 atm pressure and when expanded through a JT valve to 1.45 atm pressure it is at a saturated liquid state. The calculations apply during steady state operation and at a flow rate of 16 g/s. The analysis of the heat exchanger was broken into two parts relating to the heat transfer mode taking place. The first part is considered the condensing part in which the helium supply stream is changed from two phase fluid to one phase liquid. The second part is the subcooling part where the liquid temperature is lowered, i.e.. subcooled. A summary of the calculations and results appears on the next page. The raw calculations follow the summary.

Rucinski, R.; /Fermilab

1993-10-04T23:59:59.000Z

243

Multidimensional numerical modeling of heat exchangers. [LMFBR  

SciTech Connect (OSTI)

A comprehensive, multidimensional, thermal-hydraulic model is developed for the analysis of shell-and-tube heat exchangers for liquid-metal services. For the shellside fluid, the conservation equations of mass, momentum, and energy for continuum fluids are modified using the concept of porosity, surface permeability and distributed resistance to account for the blockage effects due to the presence of heat-transfer tubes, flow baffles/shrouds, the support plates, etc. On the tubeside, the heat-transfer tubes are connected in parallel between the inlet and outlet plenums, and tubeside flow distribution is calculated based on the plenum-to-plenum pressure difference being equal for all tubes. It is assumed that the fluid remains single-phase on the shell side and may undergo phase-change on the tube side, thereby simulating the conditions of Liquid Metal Fast Breeder Reactor (LMFBR) intermediate heat exchangers (IHX) and steam generators (SG).

Sha, W.T.; Yang, C.I.; Kao, T.T.; Cho, S.M.

1982-01-01T23:59:59.000Z

244

Heat transfer and heat exchangers reference handbook  

SciTech Connect (OSTI)

The purpose of this handbook is to provide Rocky Flats personnel with an understanding of the basic concepts of heat transfer and the operation of heat exchangers.

Not Available

1991-01-15T23:59:59.000Z

245

Heating systems for heating subsurface formations  

DOE Patents [OSTI]

Methods and systems for heating a subsurface formation are described herein. A heating system for a subsurface formation includes a sealed conduit positioned in an opening in the formation and a heat source. The sealed conduit includes a heat transfer fluid. The heat source provides heat to a portion of the sealed conduit to change phase of the heat transfer fluid from a liquid to a vapor. The vapor in the sealed conduit rises in the sealed conduit, condenses to transfer heat to the formation and returns to the conduit portion as a liquid.

Nguyen, Scott Vinh (Houston, TX); Vinegar, Harold J. (Bellaire, TX)

2011-04-26T23:59:59.000Z

246

Metal oxide films on metal  

DOE Patents [OSTI]

A structure including a thin film of a conductive alkaline earth metal oxide selected from the group consisting of strontium ruthenium trioxide, calcium ruthenium trioxide, barium ruthenium trioxide, lanthanum-strontium cobalt oxide or mixed alkaline earth ruthenium trioxides thereof upon a thin film of a noble metal such as platinum is provided.

Wu, Xin D. (Los Alamos, NM); Tiwari, Prabhat (Los Alamos, NM)

1995-01-01T23:59:59.000Z

247

Heat flux solarimeter  

SciTech Connect (OSTI)

The solarimeter presented in this work is easy to assemble. It is calibrated and its performance is validated by means of Hottel's method. Finally, the curves obtained with this solarimeter are compared to the ones obtained with a commercial solarimeter. This device is based on the evaluation of the heat flow in a metal rod. In consequence, measurements are not affected by ambient temperature variations. On the other hand, there is a linear relationship between the temperatures measured at the rod ends and the incident radiation, as can be concluded both from the theory of its operation and the calibration lines obtained. The results obtained from the global irradiance measurements in the area of Los Polvorines (Buenos Aires Province), together with a preliminary evaluation of the solarimeter's response time, are presented in this work. (author)

Sartarelli, A.; Vera, S.; Cyrulies, E. [Instituto de Desarrollo Humano, Univ. Nac. de Gral. Sarmiento (IDH, UNGS), Los Polvorines (Argentina); Echarri, R. [Instituto de Desarrollo Humano, Univ. Nac. de Gral. Sarmiento (IDH, UNGS), Los Polvorines (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET) (Argentina); Samson, I. [INTEC (Instituto Tecnologico Santo Domingo), Santo Domingo (Dominican Republic)

2010-12-15T23:59:59.000Z

248

Heat exchanger  

DOE Patents [OSTI]

A heat exchanger comparising a shell attached at its open end to one side of a tube sheet and a detachable head connected to the other side of said tube sheet. The head is divided into a first and second chamber in fluid communication with a nozzle inlet and nozzle outlet, respectively, formed in said tube sheet. A tube bundle is mounted within said shell and is provided with inlets and outlets formed in said tube sheet in communication with said first and second chambers, respectively.

Brackenbury, Phillip J. (Richland, WA)

1986-01-01T23:59:59.000Z

249

Heat exchanger  

DOE Patents [OSTI]

A heat exchanger comparising a shell attached at its open end to one side of a tube sheet and a detachable head connected to the other side of said tube sheet. The head is divided into a first and second chamber in fluid communication with a nozzle inlet and nozzle outlet, respectively, formed in said tube sheet. A tube bundle is mounted within said shell and is provided with inlets and outlets formed in said tube sheet in communication with said first and second chambers, respectively.

Brackenbury, P.J.

1983-12-08T23:59:59.000Z

250

Accelerated (9-11 Month) MBA for UG Business Majors w/ Work Experience SAC(Fin/Actg) Fall Winter Spring Summer  

E-Print Network [OSTI]

Bus. Leadership & Ethics MKTG 610 New Product Development ACTG 620 Entrepreneurial Actg MKTG 660 Industrial Ecology DSC 566 Project & Ops Management BA 610 Bus. Leadership & Ethics MGMT 610 Energy. Leadership & Ethics ACTG 617 Taxation of Business FIN 667 Fixed Income & Debt Mkts FIN 683 Investments ACTG

251

Metal Hydride Thermal Storage: Reversible Metal Hydride Thermal Storage for High-Temperature Power Generation Systems  

SciTech Connect (OSTI)

HEATS Project: PNNL is developing a thermal energy storage system based on a Reversible Metal Hydride Thermochemical (RMHT) system, which uses metal hydride as a heat storage material. Heat storage materials are critical to the energy storage process. In solar thermal storage systems, heat can be stored in these materials during the day and released at night—when the sun is not out—to drive a turbine and produce electricity. In nuclear storage systems, heat can be stored in these materials at night and released to produce electricity during daytime peak-demand hours. PNNL’s metal hydride material can reversibly store heat as hydrogen cycles in and out of the material. In a RHMT system, metal hydrides remain stable in high temperatures (600- 800°C). A high-temperature tank in PNNL’s storage system releases heat as hydrogen is absorbed, and a low-temperature tank stores the heat until it is needed. The low-cost material and simplicity of PNNL’s thermal energy storage system is expected to keep costs down. The system has the potential to significantly increase energy density.

None

2011-12-05T23:59:59.000Z

252

Miguel Navarro Menargues, ingeniero por la UA, galardonado en los Premios Nacionales de Fin de Carrera de Educacin Universitaria  

E-Print Network [OSTI]

Miguel Navarro Menargues, ingeniero por la UA, galardonado en los Premios Nacionales de Fin de Carrera de Educación Universitaria Alicante, 6 de junio de 2013 Miguel Navarro Menargues, ingeniero. Fotografía: Miguel Navarro Menargues, galardonado muestra su diploma de reconocimiento recibido el martes en

Escolano, Francisco

253

A new cascade-type heat conversion system  

SciTech Connect (OSTI)

Various heat conversion systems have different operating temperatures. This paper shows how, in a solar energy system some of the waste heat from a thermophotovoltaic arrangement can be made to operate a thermionic power generator. The waste heat of the thermionic power generator can then be made to operate an alkali-metal thermal electric converter, and the waste heat from the alkali-metal thermal electric converter as well as the rest of the waste heat of the thermophotovoltaic system can be made to operate a methane reformation system. Stored heat from the methane reformation system can be made to operate the system at night. The overall system efficiency of the example shown is 42.6%. As a prime source of heat a nuclear pile or burning hydrogen may be used.

Newman, E. [Twenty-First Century Power Co., Northridge, CA (United States)

1996-12-31T23:59:59.000Z

254

Metal Toxicity  

Science Journals Connector (OSTI)

Problems posed to plants by metal toxicity in the soils of the world are basically of two kinds. The first kind are of natural origin. These arise either as a consequence of the nature of the parent material f...

T. McNeilly

1994-01-01T23:59:59.000Z

255

Dendritic metal nanostructures  

DOE Patents [OSTI]

Dendritic metal nanostructures made using a surfactant structure template, a metal salt, and electron donor species.

Shelnutt, John A. (Tijeras, NM); Song, Yujiang (Albuquerque, NM); Pereira, Eulalia F. (Vila Nova de Gaia, PT); Medforth, Craig J. (Winters, CA)

2010-08-31T23:59:59.000Z

256

Segmented heat exchanger  

DOE Patents [OSTI]

A segmented heat exchanger system for transferring heat energy from an exhaust fluid to a working fluid. The heat exchanger system may include a first heat exchanger for receiving incoming working fluid and the exhaust fluid. The working fluid and exhaust fluid may travel through at least a portion of the first heat exchanger in a parallel flow configuration. In addition, the heat exchanger system may include a second heat exchanger for receiving working fluid from the first heat exchanger and exhaust fluid from a third heat exchanger. The working fluid and exhaust fluid may travel through at least a portion of the second heat exchanger in a counter flow configuration. Furthermore, the heat exchanger system may include a third heat exchanger for receiving working fluid from the second heat exchanger and exhaust fluid from the first heat exchanger. The working fluid and exhaust fluid may travel through at least a portion of the third heat exchanger in a parallel flow configuration.

Baldwin, Darryl Dean (Lafayette, IN); Willi, Martin Leo (Dunlap, IL); Fiveland, Scott Byron (Metamara, IL); Timmons, Kristine Ann (Chillicothe, IL)

2010-12-14T23:59:59.000Z

257

Development of a metal hydride electrode waste treatment process  

SciTech Connect (OSTI)

Manufacturing residues of metal hydride electrodes for nickel - metal hydride batteries were chemically processed to recover the metal part and heat treated for the organic part. Chemical recovery yielded Ni-Co alloy after electrolysis of the solution and hydroxides of other metal, mainly rare earths. The organic part, pyrolyzed at 700 C, led to separation between carbon and fluorinated matter. Infrared coupling at the output of the pyrolysis furnace was used to identify the pyrolysis gases.

Bianco, J.C.; Martin, D.; Ansart, F.; Castillo, S.

1999-12-01T23:59:59.000Z

258

STUDEN T FIN ANCIAL AID AND SCHO LARSHIP S SE RVICE SUPPO RT SUCC ESS 1278 University of Oregon, Eugene OR 97403-1278 http://financialaid.uoregon.edu  

E-Print Network [OSTI]

STUDEN T FIN ANCIAL AID AND SCHO LARSHIP S SE RVICE SUPPO RT SUCC ESS 1278 University of Oregon #12;STUDEN T FIN ANCIAL AID AND SCHO LARSHIP S SE RVICE SUPPO RT SUCC ESS 1278 University of Oregon

Oregon, University of

259

High power x-ray welding of metal-matrix composites  

DOE Patents [OSTI]

A method for joining metal-matrix composites (MMCs) by using high power x-rays as a volumetric heat source is provided. The method involves directing an x-ray to the weld line between two adjacent MMCs materials to create an irradiated region or melt zone. The x-rays have a power density greater than about 10.sup.4 watts/cm.sup.2 and provide the volumetric heat required to join the MMC materials. Importantly, the reinforcing material of the metal-matrix composites remains uniformly distributed in the melt zone, and the strength of the MMCs are not diminished. In an alternate embodiment, high power x-rays are used to provide the volumetric heat required to weld metal elements, including metal elements comprised of metal alloys. In an alternate embodiment, high power x-rays are used to provide the volumetric heat required to weld metal elements, including metal elements comprised of metal alloys.

Rosenberg, Richard A. (Naperville, IL); Goeppner, George A. (Orland Park, IL); Noonan, John R. (Naperville, IL); Farrell, William J. (Flossmoor, IL); Ma, Qing (Westmont, IL)

1999-01-01T23:59:59.000Z

260

E-Print Network 3.0 - annulus metal hydride Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Introduction Metal hydride applications span a wide variety of tech nologies eg energy conversion... chemical compressors and hydrogen storage A knowledge of heat and...

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Development of New Biphasic Metal Organic Working Fluids for Subcritical  

Open Energy Info (EERE)

Biphasic Metal Organic Working Fluids for Subcritical Biphasic Metal Organic Working Fluids for Subcritical Geothermal Systems Geothermal Lab Call Project Jump to: navigation, search Last modified on July 22, 2011. Project Title Development of New Biphasic Metal Organic Working Fluids for Subcritical Geothermal Systems Project Type / Topic 1 Laboratory Call for Submission of Applications for Research, Development and Analysis of Geothermal Technologies Project Type / Topic 2 Working Fluids for Binary Power Plants Project Description In binary-cycle plants the cycle efficiency improves as pumping energy is reduced and from maximizing the enthalpy gain of the working fluid for a given amount of heat extracted from the geothermal source brine. Enthalpy gain of the working fluid in the heat exchanger occurs principally from sensible heat gained while passing through the heat exchanger in the liquid state and from vaporization of the organic working fluid near the exit of the heat exchanger. Additional heat transfer is limited after the vapor phase transition due the low thermal conductivity and heat capacity of the vapor. Also, operating pressures and temperatures are constrained by the bulk phase behavior and thermodynamic properties of the working fluid (boiling point, latent heat of vaporization, density, heat capacity, etc.). The fundamental underlying goal of this project is to overcome the cycle efficiency limitations imposed by the bulk thermodynamic proper-ties of the working fluid by introducing a metal-organic heat carrier (MOHC) into the system.

262

Development of high-temperature heat exchanger for hydrogen combustion turbine system  

SciTech Connect (OSTI)

New Rankine Cycle and Topping Regenerative Cycle are representative 500MW power generation systems for a hydrogen combustion turbine (HCT). The energy efficiency based on HHV of these is expected to be over 60% because the inlet temperature of turbine can be increased to 1,970K. These systems comprise various heat exchangers. Especially, the development of high temperature heat exchanger dealing with the high temperature and pressure steam is very important to realize the hydrogen combustion turbine system. The high-temperature heat exchanger of New Rankine Cycle is a supercritical heat recovery steam generator operating at pressure of 36MPa. This heat exchanger is heated by steam at temperature of 1,390K. On the other hand, Topping Regenerative Cycle has two high-temperature heat exchangers. One is a regenerator operating at pressure of 37MPa. The other is a regenerator operating at pressure of 5MPa. Both regenerators are heated by steam at temperature of 1,030K. The following are the principal development subject of high-temperature heat exchanger: (1) Improving the heat transfer characteristics to achieve the compact heat exchanger, and (2) Planning the heat exchanger structure suitable for the high thermal stress. To improve a heat transfer characteristic of the high-temperature heat exchangers, a parameter survey is conducted to optimize a tube arrangement and a fin configuration on tube outside and/or inside. The heat transfer areas are minimized through using the tubes with an extended heat transfer surface on both sides of a tube. Structural integrity is also estimated by conducting a structural analysis for the critical parts of the high-temperature heat exchangers.

Takakuwa, Akihiro; Mochida, Yoshio

1999-07-01T23:59:59.000Z

263

The Role of Filtration in Maintaining Clean Heat Exchanger Coils  

SciTech Connect (OSTI)

The main purpose of the study was to investigate the role of filtration in maintaining clean heat exchanger coils and overall performance. Combinations of 6 different levels of filtration (MERV 14, 11, 8, 6, 4, and no filter) and 4 different coils (an eight-row lanced-fin coil, HX8L), (an eight-row wavy-fin coil, HX8W), (a four-row lanced-fin coil, HX4L) and (a two-row lanced-fin coil, HX2L) were tested at 4 different air velocities (1.52, 2.03, 2.54,3.05 m/s (300, 400, 500, 600 ft/min)). The fouled conditions were obtained after injection of 600 grams of ASHRAE standard dust upstream of the filter/coil combination. This magnitude of dust is representative of a year of normal operation for an air conditioning system. The air-side pressure drops of the coils and filters and air-side heat transfer coefficients of the coils were determined from the measurements under the clean and fouled conditions. Depending upon the filter and coil test, the coil pressure drops increased in the range of 6%-30% for an air velocity at 2.54 m/s (500 ft/min). The impact was significantly greater for tests performed without a filter. The largest relative effect of fouling on pressure drop occurs for coils with fewer rows and having lanced fins. Coils with a greater number of rows can hold more dust so that a fixed amount of dust has a relatively smaller impact. The impact of fouling on air-side heat transfer coefficients was found to be relatively small. In some cases, heat transfer was actually enhanced due to additional turbulence caused by the presence of dust. The experimental results for pressure drops and heat transfer coefficients were correlated and the correlations were implemented within computer models of prototypical rooftop air conditioners and used to evaluate the impact of fouling on cooling capacity and EER. The equipment cooling capacity is reduced with fouling primarily because of a decrease in air flow due to the increase pressure drop rather than due to changes in h eat transfer coefficient. In most cases, the EER was reduced with fouling primarily due to increased fan power. However, the changes in EER were relatively small, in the range of 1%-9% (10%). For most cases, equipment having low efficiency filters had higher EER after fouling than equipment with high efficiency filters, because the high efficiency filter caused significantly higher pressure drops than the low efficiency filters. The extra filter pressure drop outweighed the reduced coil pressure drop after fouling. The impact of fan efficiency curves was also investigated in the study. The energy penalty associated with high efficiency filters was reduced considerably with higher efficiency fans. There is an energy penalty associated with the use of high efficiency filtration. However, the primary reason for selecting high efficiency filters for a particular application would be improved air quality. For HX8L, the quantity of dust passing through the coil with a MERV4 filter was approximately 30 times the dust passing the coil with a MERV14 filter. Without an upstream filter, the quantity of dust passing through the coil was approximately 60 times the value for a MERV14 filter.

Li Yang; James E. Braun; Eckhard A. Groll

2004-06-30T23:59:59.000Z

264

Composite metal membrane  

DOE Patents [OSTI]

A composite metal membrane including a first metal layer of Group IVB met or Group VB metals, the first metal layer sandwiched between two layers of an oriented metal of palladium, platinum or alloys thereof is provided together with a process for the recovery of hydrogen from a gaseous mixture including contacting a hydrogen-containing gaseous mixture with a first side of a nonporous composite metal membrane including a first metal of Group IVB metals or Group VB metals, the first metal layer sandwiched between two layers of an oriented metal of palladium, platinum or alloys thereof, and, separating hydrogen from a second side of the nonporous composite metal membrane.

Peachey, Nathaniel M. (Espanola, NM); Dye, Robert C. (Los Alamos, NM); Snow, Ronny C. (Los Alamos, NM); Birdsell, Stephan A. (Los Alamos, NM)

1998-01-01T23:59:59.000Z

265

Composite metal membrane  

DOE Patents [OSTI]

A composite metal membrane including a first metal layer of Group IVB met or Group VB metals, the first metal layer sandwiched between two layers of an oriented metal of palladium, platinum or alloys thereof is provided together with a process for the recovery of hydrogen from a gaseous mixture including contacting a hydrogen-containing gaseous mixture with a first side of a nonporous composite metal membrane including a first metal of Group IVB metals or Group VB metals, the first metal layer sandwiched between two layers of an oriented metal of palladium, platinum or alloys thereof, and, separating hydrogen from a second side of the nonporous composite metal membrane.

Peachey, N.M.; Dye, R.C.; Snow, R.C.; Birdsell, S.A.

1998-04-14T23:59:59.000Z

266

Heat Pump for High School Heat Recovery  

E-Print Network [OSTI]

ICEBO2006, Shenzhen, China Renewable Energy Resources and a Greener Future Vol.VIII-12-1 Heat Pump for High School Bathroom Heat Recovery Kunrong Huang Hanqing Wang Xiangjiang Zhou Associate professor Professor Professor School...

Huang, K.; Wang, H.; Zhou, X.

2006-01-01T23:59:59.000Z

267

Thaw flow control for liquid heat transport systems  

DOE Patents [OSTI]

In a liquid metal heat transport system including a source of thaw heat for use in a space reactor power system, the thaw flow throttle or control comprises a fluid passage having forward and reverse flow sections and a partition having a plurality of bleed holes therein to enable fluid flow between the forward and reverse sections. The flow throttle is positioned in the system relatively far from the source of thaw heat.

Kirpich, Aaron S. (Broomall, PA)

1989-01-01T23:59:59.000Z

268

Pagosa Springs District Heating District Heating Low Temperature...  

Open Energy Info (EERE)

Pagosa Springs District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Pagosa Springs District Heating District Heating Low...

269

Boise City Geothermal District Heating District Heating Low Temperatur...  

Open Energy Info (EERE)

Boise City Geothermal District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Boise City Geothermal District Heating District Heating...

270

San Bernardino District Heating District Heating Low Temperature...  

Open Energy Info (EERE)

San Bernardino District Heating District Heating Low Temperature Geothermal Facility Facility San Bernardino District Heating Sector Geothermal energy Type District Heating...

271

Kethcum District Heating District Heating Low Temperature Geothermal...  

Open Energy Info (EERE)

Kethcum District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Kethcum District Heating District Heating Low Temperature Geothermal...

272

Philip District Heating District Heating Low Temperature Geothermal...  

Open Energy Info (EERE)

Philip District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Philip District Heating District Heating Low Temperature Geothermal...

273

Midland District Heating District Heating Low Temperature Geothermal...  

Open Energy Info (EERE)

Midland District Heating District Heating Low Temperature Geothermal Facility Facility Midland District Heating Sector Geothermal energy Type District Heating Location Midland,...

274

Combined Heat and Power, Waste Heat, and District Energy | Department...  

Broader source: Energy.gov (indexed) [DOE]

Combined Heat and Power, Waste Heat, and District Energy Combined Heat and Power, Waste Heat, and District Energy Presentation-given at the Fall 2011 Federal Utility Partnership...

275

Waste Heat Management Options for Improving Industrial Process Heating Systems  

Broader source: Energy.gov [DOE]

This presentation covers typical sources of waste heat from process heating equipment, characteristics of waste heat streams, and options for recovery including Combined Heat and Power.

276

Guide to Geothermal Heat Pumps  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Geothermal Heat Pumps Work Using a heat exchanger, a geothermal heat pump can move heat from one space to another. In summer, the geothermal heat pump extracts heat from a building...

277

Hydrocarbon Separations in Metal–Organic Frameworks  

Science Journals Connector (OSTI)

Given the large differences in the physical properties of methane and C2 hydrocarbons, both size selective effects and metal–hydrocarbon interactions can be tuned to achieve a high selectivity within a metal–organic framework. ... Polycyclic aromatic hydrocarbons, or PAHs, are carcinogenic byproducts of incomplete combustion of organic matter such as fossil fuels. ... data and the heats of adsorption were found to fit well to a small group of mol. ...

Zoey R. Herm; Eric D. Bloch; Jeffrey R. Long

2013-11-22T23:59:59.000Z

278

Woven heat exchanger  

DOE Patents [OSTI]

This invention relates to a heat exchanger for waste heat recovery from high temperature industrial exhaust streams. In a woven ceramic heat exchanger using the basic tube-in-shell design, each heat exchanger consisting of tube sheets and tube, is woven separately. Individual heat exchangers are assembled in cross-flow configuration. Each heat exchanger is woven from high temperature ceramic fiber, the warp is continuous from tube to tube sheet providing a smooth transition and unitized construction.

Piscitella, R.R.

1984-07-16T23:59:59.000Z

279

Towards Intelligent District Heating.  

E-Print Network [OSTI]

??A district heating system consists of one or more production units supplying energy in the form of heated water through a distribution pipe network to… (more)

Johansson, Christian

2010-01-01T23:59:59.000Z

280

Total Space Heat-  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

Buildings Energy Consumption Survey: Energy End-Use Consumption Tables Total Space Heat- ing Cool- ing Venti- lation Water Heat- ing Light- ing Cook- ing Refrig- eration...

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

ARM - Heat Index Calculations  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

FAQ Just for Fun Meet our Friends Cool Sites Teachers Teachers' Toolbox Lesson Plans Heat Index Calculations Heat Index is an index that combines air temperature and relative...

282

Effect of electric field on heat transfer performance of automobile radiator at low frontal air velocity  

Science Journals Connector (OSTI)

The effect of electric field on the performance of automobile radiator is investigated in this work. In this experiment, a louvered fin and flat tube automobile radiator was mounted in a wind tunnel and there was heat exchange between a hot water stream circulating inside the tube and a cold air stream flowing through the external surface. The electric field was supplied on the airside of the heat exchanger and its supply voltage was adjusted from 0 kV to 12 kV. From the experiment, it was found that the unit with electric field pronounced better heat transfer rate, especially at low frontal velocity of air. The correlations for predicting the air-side heat transfer coefficient of the automobile radiator, with and without electric field, at low frontal air velocity were also developed and the predicted results agreed very well with the experimental data.

S. Vithayasai; T. Kiatsiriroat; A. Nuntaphan

2006-01-01T23:59:59.000Z

283

Experimental confirmation of the propulsion of marine vessels employing guided flexural waves in attached elastic fins  

Science Journals Connector (OSTI)

This paper describes the results of the first experimental verification of the idea of wave-like aquatic propulsion of manned marine vessels first published by the first author in 1994. The idea is based on employing the unique type of guided flexural elastic waves propagating along edges of immersed wedge-like structures attached to a body of a small ship or a submarine as keels or wings and used for the propulsion. The principle of employing such guided flexural waves as a source of aquatic propulsion is similar to that used in nature by stingrays. It is vitally important for the application of this idea to manned vessels that, in spite of vibration of the fins, the main body of the craft remains undisturbed as the energy of guided elastic waves is concentrated away from it. The main expected advantages of this new propulsion method over the existing ones, e.g. jets and propellers, are the following: it is quiet, and it is environmentally friendly and safe for people and wildlife. To verify the idea experimentally, the first working prototype of a small catamaran using the above-mentioned wave-like propulsion via the attached rubber keel has been built and tested. The test results have shown that the catamaran was propelled efficiently and could achieve the speed of 36 cm/s, thus demonstrating that the idea of wave-like propulsion of manned craft is viable. The reported proof of the viability of this idea may open new opportunities for marine craft propulsion, which can have far-reaching implications.

V.V. Krylov; G.V. Pritchard

2007-01-01T23:59:59.000Z

284

Heating Facilities, Virginia Lake Townhouses and Apartments, Reno, Nevada.  

SciTech Connect (OSTI)

The Virginia Lake Townhouses and Apartments are located in a 12 acre parcel in the geographic center of Reno, Nevada. There are 148 apartments, consisting of 70 single story garden apartments in 10 buildings, 40 two story townhouses in six buildings, and 38 two story apartments in five buildings. All apartments are presently heated with individual natural gas fired forced air furnaces. Hot water is provided by gas fired water heaters, except for the 40 older townhouses which are using water directly from a geothermal source. This water has now been found to be unsuitable for potable use. Located on the property are two geothermal wells, complete with pumps. The larger well can deliver 500 gallons per min., and the smaller well 65 gallons per min., of the 135/sup 0/F geothermal water. The Geo-Heat Utilization Center has been asked to determine a scheme for using the geothermal water from these wells to provide the needed space and hot water heating for the 148 apartments. An outdoor swimming pool also requires heating. Space heating in all three types of apartments will be accomplished through the installation of finned water coils in existing ductwork or furnaces. Geothermal water will be pumped from Well No. 2 through a main distribution system and used directly in the coils. Piping system specifics are available in the Appendix.

Not Available

1980-03-01T23:59:59.000Z

285

Process for removing heavy metal compounds from heavy crude oil  

DOE Patents [OSTI]

A process is provided for removing heavy metal compounds from heavy crude oil by mixing the heavy crude oil with tar sand; preheating the mixture to a temperature of about 650.degree. F.; heating said mixture to up to 800.degree. F.; and separating tar sand from the light oils formed during said heating. The heavy metals removed from the heavy oils can be recovered from the spent sand for other uses.

Cha, Chang Y. (Golden, CO); Boysen, John E. (Laramie, WY); Branthaver, Jan F. (Laramie, WY)

1991-01-01T23:59:59.000Z

286

Aging of Iron (Hydr)oxides by Heat Treatment and Effects on Heavy  

E-Print Network [OSTI]

)oxides are used to remove heavy metals from wastewater and in the treatment of air pollution control residuesAging of Iron (Hydr)oxides by Heat Treatment and Effects on Heavy Metal Binding M E T T E A . S Ã? R generated in waste incineration. In this study, iron oxides containing heavy metals (e.g., Pb, Hg, Cr

Frenkel, Anatoly

287

Conceptual design selection and development of a latent-heat thermal-energy-storage subsystem for a saturated-steam solar receiver and load  

SciTech Connect (OSTI)

The following latent heat storage concepts are described and evaluated in comparison with each other and with an oil/rock sensible heat storage system: (1) passive tube intensive (shell-and-tube heat exchanger) with and without heat transfer enhanced by fins; (2) phase change material cans (or chubbs) with a biphenyl intermediate heat transfer fluid; (3) phase change material macroencapsulation in a containment tank full of tubes; (4) microencapsulation in a porous carrier; (5) direct contact heat exchange; and (6) systems using mechanical scrapers for removing solidified phase change material from container surfaces. A tube intensive system with heat transfer enhancement was selected, and the conceptual design and cost/performance estimates are given for it. A commercial scale unit is assessed, and design changes and corresponding costs are presented that would be required to make the system meet changed requirements. (LEW)

Not Available

1981-02-01T23:59:59.000Z

288

Laser Welding of Metals [Laser Applications Laboratory] - Nuclear  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Laser Welding of Metals Laser Welding of Metals Capabilities Engineering Experimentation Reactor Safety Experimentation Aerosol Experiments System Components Laser Applications Overview Laser Oil & Gas Well Drilling Laser Heat Treatment Laser Welding of Metals On-line Monitoring Laser Beam Delivery Laser Glazing of Railroad Rails High Power Laser Beam Delivery Decontamination and Decommissioning Refractory Alloy Welding Robots Applications Other Facilities Other Capabilities Work with Argonne Contact us For Employees Site Map Help Join us on Facebook Follow us on Twitter NE on Flickr Laser Applications Laboratory Laser Welding of Metals Project description: High-speed laser welding of metals. Category: Project with industrial partner (Delphi Energy and Engine Management Systems) Bookmark and Share

289

Sewage sludge dewatering using flowing liquid metals  

DOE Patents [OSTI]

A method and apparatus for reducing the moisture content of a moist sewage sludge having a moisture content of about 50% to 80% and formed of small cellular micro-organism bodies having internally confined water is provided. A hot liquid metal is circulated in a circulation loop and the moist sewage sludge is injected in the circulation loop under conditions of temperature and pressure such that the confined water vaporizes and ruptures the cellular bodies. The vapor produced, the dried sludge, and the liquid metal are then separated. Preferably, the moist sewage sludge is injected into the hot liquid metal adjacent the upstream side of a venturi which serves to thoroughly mix the hot liquid metal and the moist sewage sludge. The venturi and the drying zone after the venturi are preferably vertically oriented. The dried sewage sludge recovered is available as a fuel and is preferably used for heating the hot liquid metal.

Carlson, Larry W. (Oswego, IL)

1986-01-01T23:59:59.000Z

290

Rotary magnetic heat pump  

DOE Patents [OSTI]

A rotary magnetic heat pump constructed without flow seals or segmented rotor accomplishes recuperation and regeneration by using split flow paths. Heat exchange fluid pumped through heat exchangers and returned to the heat pump splits into two flow components: one flowing counter to the rotor rotation and one flowing with the rotation. 5 figs.

Kirol, L.D.

1987-02-11T23:59:59.000Z

291

The effects of topology upon fluid-flow and heat-transfer within cellular copper structures  

E-Print Network [OSTI]

1 The effects of topology upon fluid-flow and heat-transfer within cellular copper structures J The fluid-flow and heat-transfer features of copper cellular metal structures made by the transient liquid media. The experimental results for pressure drop and heat transfer were expressed on the basis

Wadley, Haydn

292

Thulium-170 heat source  

SciTech Connect (OSTI)

An isotopic heat source is formed using stacks of thin individual layers of a refractory isotopic fuel, preferably thulium oxide, alternating with layers of a low atomic weight diluent, preferably graphite. The graphite serves several functions: to act as a moderator during neutron irradiation, to minimize bremsstrahlung radiation, and to facilitate heat transfer. The fuel stacks are inserted into a heat block, which is encased in a sealed, insulated and shielded structural container. Heat pipes are inserted in the heat block and contain a working fluid. The heat pipe working fluid transfers heat from the heat block to a heat exchanger for power conversion. Single phase gas pressure controls the flow of the working fluid for maximum heat exchange and to provide passive cooling.

Walter, C.E.; Van Konynenburg, R.; VanSant, J.H.

1990-09-06T23:59:59.000Z

293

Thulium-170 heat source  

DOE Patents [OSTI]

An isotopic heat source is formed using stacks of thin individual layers of a refractory isotopic fuel, preferably thulium oxide, alternating with layers of a low atomic weight diluent, preferably graphite. The graphite serves several functions: to act as a moderator during neutron irradiation, to minimize bremsstrahlung radiation, and to facilitate heat transfer. The fuel stacks are inserted into a heat block, which is encased in a sealed, insulated and shielded structural container. Heat pipes are inserted in the heat block and contain a working fluid. The heat pipe working fluid transfers heat from the heat block to a heat exchanger for power conversion. Single phase gas pressure controls the flow of the working fluid for maximum heat exchange and to provide passive cooling.

Walter, Carl E. (Pleasanton, CA); Van Konynenburg, Richard (Livermore, CA); VanSant, James H. (Tracy, CA)

1992-01-01T23:59:59.000Z

294

Heat Treating Apparatus  

DOE Patents [OSTI]

Apparatus for heat treating a heat treatable material including a housing having an upper opening for receiving a heat treatable material at a first temperature, a lower opening, and a chamber therebetween for heating the heat treatable material to a second temperature higher than the first temperature as the heat treatable material moves through the chamber from the upper to the lower opening. A gas supply assembly is operatively engaged to the housing at the lower opening, and includes a source of gas, a gas delivery assembly for delivering the gas through a plurality of pathways into the housing in countercurrent flow to movement of the heat treatable material, whereby the heat treatable material passes through the lower opening at the second temperature, and a control assembly for controlling conditions within the chamber to enable the heat treatable material to reach the second temperature and pass through the lower opening at the second temperature as a heated material.

De Saro, Robert (Annandale, NJ); Bateman, Willis (Sutton Colfield, GB)

2002-09-10T23:59:59.000Z

295

Thermoelectric heat exchange element  

DOE Patents [OSTI]

A thermoelectric heat exchange module includes a first substrate including a heat receptive side and a heat donative side and a series of undulatory pleats. The module may also include a thermoelectric material layer having a ZT value of 1.0 or more disposed on at least one of the heat receptive side and the heat donative side, and an electrical contact may be in electrical communication with the thermoelectric material layer.

Callas, James J. (Peoria, IL); Taher, Mahmoud A. (Peoria, IL)

2007-08-14T23:59:59.000Z

296

Heat pipe cooling for scramjet engines. Final report  

SciTech Connect (OSTI)

Liquid metal heat pipe cooling systems have been investigated for the combustor liner and engine inlet leading edges of scramjet engines for a missile application. The combustor liner is cooled by a lithium-TZM molybdenum annular heat pipe, which incorporates a separate lithium reservoir. Heat is initially absorbed by the sensible thermal capacity of the heat pipe and liner, and subsequently by the vaporization and discharge of lithium to the atmosphere. The combustor liner temperature is maintained at 3400 F or less during steady-state cruise. The engine inlet leading edge is fabricated as a sodium-superalloy heat pipe. Cooling is accomplished by radiation of heat from the aft surface of the leading edge to the atmosphere. The leading edge temperature is limited to 1700 F or less. It is concluded that heat pipe cooling is a viable method for limiting scramjet combustor liner and engine inlet temperatures to levels at which structural integrity is greatly enhanced.

Silverstein, C.C.

1986-12-01T23:59:59.000Z

297

Heat-pipe gas-combustion system endurance test for Stirling engine. Final report, May 1990-September 1990  

SciTech Connect (OSTI)

Stirling Thermal Motors, Inc., (STM) has been developing a general purpose Heat Pipe Gas Combustion System (HPGC) suitable for use with the STM4-120 Stirling engine. The HPGC consists of a parallel plate recuperative preheater, a finned heat pipe evaporator and a film cooled gas combustor. A principal component of the HPGC is the heat pipe evaporator which collects and distributes the liquid sodium over the heat transfer surfaces. The liquid sodium evaporates and flows to the condensers where it delivers its latent heat. The report presents test results of endurance tests run on a Gas-Fired Stirling Engine (GFSE). Tests on a dynamometer test stand yielded 67 hours of engine operation at power levels over 10 kW (13.5 hp) with 26 hours at power levels above 15 kW (20 hp). Total testing of the engine, including both motoring tests and engine operation, yielded 245 hours of engine run time.

Mahrle, P.

1990-12-01T23:59:59.000Z

298

Mechanochemical processing for metals and metal alloys  

DOE Patents [OSTI]

A set of processes for preparing metal powders, including metal alloy powders, by ambient temperature reduction of a reducible metal compound by a reactive metal or metal hydride through mechanochemical processing. The reduction process includes milling reactants to induce and complete the reduction reaction. The preferred reducing agents include magnesium and calcium hydride powders. A process of pre-milling magnesium as a reducing agent to increase the activity of the magnesium has been established as one part of the invention.

Froes, Francis H. (Moscow, ID); Eranezhuth, Baburaj G. (Moscow, ID); Prisbrey, Keith (Moscow, ID)

2001-01-01T23:59:59.000Z

299

Heavy metals behaviour in a gasification reactor  

Science Journals Connector (OSTI)

Sludge coming from cleaning processes of wastewater, Municipal Solid Waste (MSW), and Refuse Derived Fuel (RDF) can be exploited for producing energy because of their heating value. Cleaning the produced syngas is important because of environmental troubles, ... Keywords: heavy metals, syngas, thermodynamic, waste gasification

Martino Paolucci; Carlo Borgianni; Paolo De Filippis

2011-07-01T23:59:59.000Z

300

Heat Integrate Heat Engines in Process Plants  

E-Print Network [OSTI]

and refrigeration systems. In many instances these real heat engines may appear as a complex process consisting of flash vessels, heat exchangers, compressors, furnaces, etc. See Figure 18a, which shows a simplified diagram of a "steam Rankine cycle." How... and rejection profiles of the real machine. For example, the heat acceptance and re jection profiles for the steam Rankine cycle shown in Figure 18a have been drawn on T,H coordinates in Figure 18b. Thus providing we know the heat acceptance and rejection...

Hindmarsh, E.; Boland, D.; Townsend, D. W.

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

System and method for producing metallic iron  

DOE Patents [OSTI]

A method of production of metallic iron nodules comprises assembling a hearth furnace having a moveable hearth comprising refractory material and having a conversion zone and a fusion zone, providing a hearth material layer comprising carbonaceous material on the refractory material, providing a layer of reducible material comprising and iron bearing material arranged in discrete portions over at least a portion of the hearth material layer, delivering oxygen gas into the hearth furnace to a ratio of at least 0.8:1 ponds of oxygen to pounds of iron in the reducible material to heat the conversion zone to a temperature sufficient to at least partially reduce the reducible material and to heat the fusion zone to a temperature sufficient to at least partially reduce the reducible material, and heating the reducible material to form one or more metallic iron nodules and slag.

Englund, David J.; Schlichting, Mark; Meehan, John; Crouch, Jeremiah; Wilson, Logan

2014-07-29T23:59:59.000Z

302

Renewable energy of waste heat recovery system for automobiles  

Science Journals Connector (OSTI)

A system to recover waste heat comprised of eight thermoelectric generators (TEGs) to convert heat from the exhaust pipe of an automobile to electrical energy has been constructed. Simulations and experiments for the thermoelectric module in this system are undertaken to assess the feasibility of these applications. In order to estimate the temperature difference between thermoelectric elements a network of thermal resistors is constructed. The results assist in predicting power output of TEG module more precisely. Three configurations of heat sinks which are comprised of 10 22 and 44 fins are applied in this simulation. The results of the simulations show the average thermal resistance of these heat sinks in each section of the system with varied velocity of external flow. As the performance of a TEG module is influenced by an applied pressure through the effect of the thermal contact resistance we clamp the TE module to our experimental apparatus; the relation between power output and pressure applied in this case is presented. Besides simulations the system is designed and assembled. Measurements followed the connection of the system to the middle of an exhaust pipe. Through these simulations and experiments the power generated with a commercial TEG is presented. The results establish the fundamental development of materials that enhance the TEG efficiency for vehicles.

Cheng-Ting Hsu; Da-Jeng Yao; Ke-Jyun Ye; Ben Yu

2010-01-01T23:59:59.000Z

303

Heat transfer system  

DOE Patents [OSTI]

A heat transfer system for a nuclear reactor. Heat transfer is accomplished within a sealed vapor chamber which is substantially evacuated prior to use. A heat transfer medium, which is liquid at the design operating temperatures, transfers heat from tubes interposed in the reactor primary loop to spaced tubes connected to a steam line for power generation purposes. Heat transfer is accomplished by a two-phase liquid-vapor-liquid process as used in heat pipes. Condensible gases are removed from the vapor chamber through a vertical extension in open communication with the chamber interior.

McGuire, Joseph C. (Richland, WA)

1982-01-01T23:59:59.000Z

304

Wound tube heat exchanger  

DOE Patents [OSTI]

What is disclosed is a wound tube heat exchanger in which a plurality of tubes having flattened areas are held contiguous adjacent flattened areas of tubes by a plurality of windings to give a double walled heat exchanger. The plurality of windings serve as a plurality of effective force vectors holding the conduits contiguous heat conducting walls of another conduit and result in highly efficient heat transfer. The resulting heat exchange bundle is economical and can be coiled into the desired shape. Also disclosed are specific embodiments such as the one in which the tubes are expanded against their windings after being coiled to insure highly efficient heat transfer.

Ecker, Amir L. (Duncanville, TX)

1983-01-01T23:59:59.000Z

305

Heat Exchangers for Solar Water Heating Systems | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Heat Exchangers for Solar Water Heating Systems Heat Exchangers for Solar Water Heating Systems Heat Exchangers for Solar Water Heating Systems May 30, 2012 - 3:40pm Addthis Image of a heat exchanger. | Photo from iStockphoto.com Image of a heat exchanger. | Photo from iStockphoto.com Solar water heating systems use heat exchangers to transfer solar energy absorbed in solar collectors to the liquid or air used to heat water or a space. Heat exchangers can be made of steel, copper, bronze, stainless steel, aluminum, or cast iron. Solar heating systems usually use copper, because it is a good thermal conductor and has greater resistance to corrosion. Types of Heat Exchangers Solar water heating systems use three types of heat exchangers: Liquid-to-liquid A liquid-to-liquid heat exchanger uses a heat-transfer fluid that

306

Electronic properties of a simple metal-metal interface  

Science Journals Connector (OSTI)

The properties of metal-metal interfaces are of interest in many metallurgical applications. These include grain boundaries, crack growth, friction, and bimetallic adhesion. The present work is a study of the electronic properties of a simple bimetallic junction. The methods employed to investigate the interface are the Green's-function technique and the phase-shift method. We calculate the Green's function of a simple junction within the tight-binding approximation. The conditions for the occurrence of bound states are deduced from the poles of the Green's function. Using the phase-shift method we derive an expression for the change in density of states due to the creation of the interface. From this expression we derive the corresponding single-particle contribution to the interface energy and the interface specific heat.

Avishay Yaniv

1978-05-15T23:59:59.000Z

307

Double-sided electromagnetic pump with controllable normal force for rapid solidification of liquid metals  

DOE Patents [OSTI]

A system for casting liquid metals is provided with an electromagnetic pump which includes a pair of primary blocks each having a polyphase winding and being positioned to form a gap through which a movable conductive heat sink passes. A solidifying liquid metal sheet is deposited on the heat sink and the heat sink and sheet are held in compression by forces produced as a result of current flow through the polyphase windings. Shaded-pole interaction between the primary windings, heat sink and solidifying strip produce transverse forces which act to center the strip on the heat sink. 5 figs.

Kuznetsov, S.B.

1987-01-13T23:59:59.000Z

308

Geothermal Heat Pumps  

Broader source: Energy.gov [DOE]

The Geothermal Technologies Office focuses only on electricity generation. For additional information about geothermal heating and cooling and ground source heat pumps, please visit the U.S. Department of Energy (DOE)'s Buildings Technologies Office.

309

HEAT TRANSFER FLUIDS  

E-Print Network [OSTI]

The choice of heat transfer fluids has significant effects on the performance, cost, and reliability of solar thermal systems. In this chapter, we evaluate existing heat transfer fluids such as oils and molten salts based ...

Lenert, Andrej

2012-01-01T23:59:59.000Z

310

Residential heating oil price  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

heating oil price decreases The average retail price for home heating oil fell 6.3 cents from a week ago to 2.91 per gallon. That's down 1.10 from a year ago, based on the...

311

Residential heating oil price  

U.S. Energy Information Administration (EIA) Indexed Site

heating oil price decreases The average retail price for home heating oil fell 7.5 cents from a week ago to 2.84 per gallon. That's down 1.22 from a year ago, based on the...

312

Residential heating oil price  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

heating oil price decreases The average retail price for home heating oil fell 7.6 cents from a week ago to 2.97 per gallon. That's down 1.05 from a year ago, based on the...

313

Residential heating oil price  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

heating oil price decreases The average retail price for home heating oil fell 3.6 cents from a week ago to 3.04 per gallon. That's down 99.4 cents from a year ago, based on the...

314

Method for passive cooling liquid metal cooled nuclear reactors, and system thereof  

DOE Patents [OSTI]

A liquid metal cooled nuclear reactor having a passive cooling system for removing residual heat resulting from fuel decay during reactor shutdown. The passive cooling system comprises a plurality of partitions surrounding the reactor vessel in spaced apart relation forming intermediate areas for circulating heat transferring fluid which remove and carry away heat from the reactor vessel.

Hunsbedt, Anstein (Los Gatos, CA); Busboom, Herbert J. (San Jose, CA)

1991-01-01T23:59:59.000Z

315

Metal-phosphate binders  

DOE Patents [OSTI]

A metal-phosphate binder is provided. The binder may include an aqueous phosphoric acid solution, a metal-cation donor including a metal other than aluminum, an aluminum-cation donor, and a non-carbohydrate electron donor.

Howe, Beth Ann [Lewistown, IL; Chaps-Cabrera, Jesus Guadalupe [Coahuila, MX

2009-05-12T23:59:59.000Z

316

MA HEAT Loan Overview  

Broader source: Energy.gov [DOE]

Presents information on the success of Massachusetts's HEAT loan offerings and how the financing tool is funded.

317

Ductless Heat Pumps  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Water Heaters Showerheads Residential Weatherization Performance Tested Comfort Systems Ductless Heat Pumps New Construction Residential Marketing Toolkit Retail Sales...

318

Heat Pump Water Heaters  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Water Heaters Showerheads Residential Weatherization Performance Tested Comfort Systems Ductless Heat Pumps New Construction Residential Marketing Toolkit Retail Sales...

319

Solar heat receiver  

DOE Patents [OSTI]

A receiver is described for converting solar energy to heat a gas to temperatures from 700 to 900/sup 0/C. The receiver is formed to minimize impingement of radiation on the walls and to provide maximum heating at and near the entry of the gas exit. Also, the receiver is formed to provide controlled movement of the gas to be heated to minimize wall temperatures. The receiver is designed for use with gas containing fine heat absorbing particles, such as carbon particles.

Hunt, A.J.; Hansen, L.J.; Evans, D.B.

1982-09-29T23:59:59.000Z

320

Electric resistive space heating  

Science Journals Connector (OSTI)

The cost of heating residential buildings using electricity is compared to the cost employing gas or oil. (AIP)

David Bodansky

1985-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Influence of uranium hydride oxidation on uranium metal behaviour  

SciTech Connect (OSTI)

This work addresses concerns that the rapid, exothermic oxidation of active uranium hydride in air could stimulate an exothermic reaction (burning) involving any adjacent uranium metal, so as to increase the potential hazard arising from a hydride reaction. The effect of the thermal reaction of active uranium hydride, especially in contact with uranium metal, does not increase in proportion with hydride mass, particularly when considering large quantities of hydride. Whether uranium metal continues to burn in the long term is a function of the uranium metal and its surroundings. The source of the initial heat input to the uranium, if sufficient to cause ignition, is not important. Sustained burning of uranium requires the rate of heat generation to be sufficient to offset the total rate of heat loss so as to maintain an elevated temperature. For dense uranium, this is very difficult to achieve in naturally occurring circumstances. Areas of the uranium surface can lose heat but not generate heat. Heat can be lost by conduction, through contact with other materials, and by convection and radiation, e.g. from areas where the uranium surface is covered with a layer of oxidised material, such as burned-out hydride or from fuel cladding. These rates of heat loss are highly significant in relation to the rate of heat generation by sustained oxidation of uranium in air. Finite volume modelling has been used to examine the behaviour of a magnesium-clad uranium metal fuel element within a bottle surrounded by other un-bottled fuel elements. In the event that the bottle is breached, suddenly, in air, it can be concluded that the bulk uranium metal oxidation reaction will not reach a self-sustaining level and the mass of uranium oxidised will likely to be small in relation to mass of uranium hydride oxidised. (authors)

Patel, N.; Hambley, D. [National Nuclear Laboratory (United Kingdom); Clarke, S.A. [Sellafield Ltd (United Kingdom); Simpson, K.

2013-07-01T23:59:59.000Z

322

Liquid heat capacity lasers  

DOE Patents [OSTI]

The heat capacity laser concept is extended to systems in which the heat capacity lasing media is a liquid. The laser active liquid is circulated from a reservoir (where the bulk of the media and hence waste heat resides) through a channel so configured for both optical pumping of the media for gain and for light amplification from the resulting gain.

Comaskey, Brian J. (Walnut Creek, CA); Scheibner, Karl F. (Tracy, CA); Ault, Earl R. (Livermore, CA)

2007-05-01T23:59:59.000Z

323

Heat Transfer Guest Editorial  

E-Print Network [OSTI]

Journal of Heat Transfer Guest Editorial We are indeed delighted in bringing out this special issue was showcased in diverse areas such as traditional heat and mass transfer, lab-on-chip, sensors, biomedical applica- tions, micromixers, fuel cells, and microdevices. Selected papers in the field of heat transfer

Kandlikar, Satish

324

Acoustic Heating Peter Ulmschneider  

E-Print Network [OSTI]

Acoustic Heating Peter Ulmschneider lnstitut fiir Theoretische Astrophysik der Universitat waves are a viable and prevalent heating mechanism both in early- and in late-type stars. Acoustic heating appears to be a dominant mechanism for situations where magnetic fields are weak or absent

Ulmschneider, Peter

325

Ammoniated salt heat pump  

SciTech Connect (OSTI)

A thermochemical heat pump/energy storage system using liquid ammoniate salts is described. The system, which can be used for space heating or cooling, provides energy storage for both functions. The bulk of the energy is stored as chemical energy and thus can be stored indefinitely. The system is well suited to use with a solar energy source or industrial waste heat.

Haas, W.R.; Jaeger, F.J.; Giordano, T.J.

1981-01-01T23:59:59.000Z

326

Pioneering Heat Pump Project  

Broader source: Energy.gov [DOE]

Project objectives: To install and monitor an innovative WaterFurnace geothermal system that is technologically advanced and evolving; To generate hot water heating from a heat pump that uses non-ozone depleting refrigerant CO2. To demonstrate the energy efficiency of this system ground source heat pump system.

327

Home Heating | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Home Heating Everything you need to know about home heating, including how heating systems work, the different types on the market and proper maintenance. Read more Thermostats...

328

Water Heating | Department of Energy  

Energy Savers [EERE]

Energy Saver Water Heating Water Heating Infographic: Water Heaters 101 Infographic: Water Heaters 101 Everything you need to know about saving money on water heating costs....

329

Metal Hydrides - Science Needs  

Broader source: Energy.gov (indexed) [DOE]

Storage Grand Challenge Pre-Solicitation Meeting, June 19, 2003 1 Metal Hydrides - Science Needs TRADITIONAL METALLIC HYDRIDES: 1.5 to 2 wt.% H. Well studied. COMPLEX...

330

Probing metal solidification nondestructively  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Probing metal solidification nondestructively This is the first time that high-energy protons have been used to nondestructively image a large metal sample during melting and...

331

Probing metal solidification nondestructively  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Probing metal solidification nondestructively This is the first time that high-energy protons have been used to nondestructively image a large metal sample during melting...

332

Liquid metal cooled divertor for ARIES  

SciTech Connect (OSTI)

A liquid metal, Ga-cooled divertor design was completed for the double null ARIES-II divertor design. The design analysis indicated a surface heat flux removal capability of up to 15 MW/m{sup 2}, and its relative easy maintenance. Design issues of configuration, thermal hydraulics, thermal stresses, liquid metal loop and safety effects were evaluated. For coolant flow control, it was found that it is necessary to use some part of the blanket cooling ducts for the draining of liquid metal from the top divertor. In order to minimize the inventory of Ga, it was recommended that the liquid metal loop equipment should be located as close to the torus as possible. More detailed analysis of transient conditions especially under accident conditions was identified as an issue that will need to be addressed.

Muraviev, E. [Gosudarstvennyj Komitet po Ispol`zovaniyu Atomnoj Ehnergii SSSR, Moscow (Russian Federation). Inst. Atomnoj Ehnergii

1995-01-01T23:59:59.000Z

333

Process for forming a metal compound coating on a substrate  

DOE Patents [OSTI]

A method of coating a substrate with a thin layer of a metal compound by forming a dispersion of an electrophoretically active organic colloid and a precursor of the metal compound in an electrolytic cell in which the substrate is an electrode. Upon application of an electric potential, the electrode is coated with a mixture of the organic colloid and the precursor to the metal compound, and the coated substrate is then heated in the presence of an atmosphere or vacuum to decompose the organic colloid and form a coating of either a combination of metal compound and carbon, or optionally forming a porous metal compound coating by heating to a temperature high enough to chemically react the carbon.

Sharp, Donald J. (Albuquerque, NM); Vernon, Milton E. (Albuquerque, NM); Wright, Steven A. (Albuquerque, NM)

1991-01-01T23:59:59.000Z

334

Process for forming a metal compound coating on a substrate  

DOE Patents [OSTI]

A method of coating a substrate with a thin layer of a metal compound by forming a dispersion of an electrophoretically active organic colloid and a precursor of the metal compound in an electrolytic cell in which the substrate is an electrode. Upon application of an electric potential, the electrode is coated with a mixture of the organic colloid and the precursor to the metal compound, and the coated substrate is then heated in the presence of an atmosphere or vacuum to decompose the organic colloid and form a coating of either a combination of metal compound and carbon, or optionally forming a porous metal compound coating by heating to a temperature high enough to chemically react the carbon.

Sharp, D.J.; Vernon, M.E.; Wright, S.A.

1988-06-29T23:59:59.000Z

335

Trending: Metal Oxo Bonds  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Trending: Metal Oxo Bonds Trending: Metal Oxo Bonds Trending: Metal Oxo Bonds Print Wednesday, 29 May 2013 00:00 Metal oxides are important for scientific and technical applications in a variety of disciplines, including materials science, chemistry, and biology. Highly covalent metal-oxygen multiple bonds (metal oxos) are the building blocks of metal oxides and have a bearing on the oxide's desirable chemical, magnetic, electronic, and thermal properties. The lack of a more sophisticated grasp of bonding in metal oxides constitutes a roadblock to innovation in a wide variety of important emergent technologies, including industrial catalysis, biomimetic transformations, and artificial photosynthesis. To address this problem, a research team from four national laboratories, three Department of Energy synchrotron user facilities, and the University of Washington has applied spectroscopic and computational analyses to a number of metal oxides, quantifying trends in metal oxo bonding for groups of metals across the periodic table.

336

Residential Heating Oil Prices  

Gasoline and Diesel Fuel Update (EIA)

This chart highlights residential heating oil prices for the current and This chart highlights residential heating oil prices for the current and past heating season. As you can see, prices have started the heating season, about 40 to 50 cents per gallon higher than last year at this time. The data presented are from EIA's State Heating Oil and Propane Program. We normally collect and publish this data twice a month, but given the low stocks and high prices, we started tracking the prices weekly. These data will also be used to determine the price trigger mechanism for the Northeast Heating Oil Reserve. The data are published at a State and regional level on our web site. The slide is to give you some perspective of what is happening in these markets, since you probably will get a number of calls from local residents about their heating fuels bills

337

Active microchannel heat exchanger  

DOE Patents [OSTI]

The present invention is an active microchannel heat exchanger with an active heat source and with microchannel architecture. The microchannel heat exchanger has (a) an exothermic reaction chamber; (b) an exhaust chamber; and (c) a heat exchanger chamber in thermal contact with the exhaust chamber, wherein (d) heat from the exothermic reaction chamber is convected by an exothermic reaction exhaust through the exhaust chamber and by conduction through a containment wall to the working fluid in the heat exchanger chamber thereby raising a temperature of the working fluid. The invention is particularly useful as a liquid fuel vaporizer and/or a steam generator for fuel cell power systems, and as a heat source for sustaining endothermic chemical reactions and initiating exothermic reactions.

Tonkovich, Anna Lee Y. (Pasco, WA) [Pasco, WA; Roberts, Gary L. (West Richland, WA) [West Richland, WA; Call, Charles J. (Pasco, WA) [Pasco, WA; Wegeng, Robert S. (Richland, WA) [Richland, WA; Wang, Yong (Richland, WA) [Richland, WA

2001-01-01T23:59:59.000Z

338

A model for improvement of water heating heat exchanger designs for residential heat pump water heaters.  

E-Print Network [OSTI]

??Heat pump water heaters are a promising technology to reduce energy use and greenhouse gas emissions. A key component is the water heating heat exchanger.… (more)

Weerawoot, Arunwattana

2010-01-01T23:59:59.000Z

339

Method of manufacturing a heat pipe wick with structural enhancement  

DOE Patents [OSTI]

Heat pipe wick structure wherein a stout sheet of perforated material overlays a high performance wick material such as stainless steel felt affixed to a substrate. The inventive structure provides a good flow path for working fluid while maintaining durability and structural stability independent of the structure (or lack of structure) associated with the wick material. In one described embodiment, a wick of randomly laid .about.8 micron thickness stainless steel fibers is sintered to a metal substrate and a perforated metal overlay.

Andraka, Charles E. (Albuquerque, NM); Adkins, Douglas R. (Albuquerque, NM); Moreno, James B. (Albuquerque, NM); Rawlinson, K. Scott (Albuquerque, NM); Showalter, Steven K. (Albuquerque, NM); Moss, Timothy A. (Albuquerque, NM)

2006-10-24T23:59:59.000Z

340

Numerical modeling of a 2K J-T heat exchanger used in Fermilab Vertical Test Stand VTS-1  

SciTech Connect (OSTI)

Fermilab Vertical Test Stand-1 (VTS-1) is in operation since 2007 for testing the superconducting RF cavities at 2 K. This test stand has single layer coiled finned tubes heat exchanger before J-T valve. A finite difference based thermal model has been developed in Engineering Equation Solver (EES) to study its thermal performance during filling and refilling to maintain the constant liquid level of test stand. The model is also useful to predict its performance under other various operating conditions and will be useful to design the similar kind of heat exchanger for future needs. Present paper discusses the different operational modes of this heat exchanger and its thermal characteristics under these operational modes. Results of this model have also been compared with the experimental data gathered from the VTS-1 heat exchanger and they are in good agreement with the present model.

Gupta, Prabhat Kumar [Raja Ramanna Centre for Advanced Technology (RRCAT), Indore (MP), India; Rabehl, Roger [FNAL

2014-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Method of enhancing selective isotope desorption from metals  

DOE Patents [OSTI]

A method of enhancing the thermal desorption of a first isotope of a diatomic gas from a metal comprises the steps of (a) establishing a partial pressure of a second isotope of the diatomic gas in vicinity of the metal; heating the metal to a temperature such that the first isotope is desorbed from the metal; and reducing the partial pressure of the desorbed first isotope while maintaining the partial pressure of the second isotope substantially constant. The method is especially useful for enhancing the desorption of tritium from the Zr-Al getter in a plasma confinement device.

Knize, Randall J. (Plainsboro, NJ); Cecchi, Joseph L. (Lawrenceville, NJ)

1984-01-01T23:59:59.000Z

342

Reaction-Forming Method for Producing Near Net-Shape Refractory Metal Carbides  

DOE Patents [OSTI]

A method for reaction forming refractory metal carbides. The method involves the fabrication of a glassy carbon preform by casting an organic, resin-based liquid mixture into a mold and subsequently heat treating it in two steps, which cures and pyrolizes the resin resulting in a porous carbon preform. By varying the amounts of the constituents in the organic, resin-based liquid mixture, control over the density of the carbon preform is obtained. Control of the density and microstructure of the carbon preform allows for determination of the microstructure and properties of the refractory metal carbide material produced. The glassy carbon preform is placed on a bed of refractory metal or refractory metal--silicon alloy. The pieces are heated above the melting point of the metal or alloy. The molten metal wicks inside the porous carbon preform and reacts, forming the refractory metal carbide or refractory metal carbide plus a minor secondary phase.

Palmisiano, Marc N.; Jakubenas, Kevin J.; Baranwal, Rita

2004-07-20T23:59:59.000Z

343

PERFORMANCE OF A STIRLING ENGINE POWERED HEAT ACTIVATED HEAT PUMP  

E-Print Network [OSTI]

PERFORMANCE OF A STIRLING ENGINE POWERED HEAT ACTIVATED HEAT PUMP W. D. C. Richards and W. L. Auxer General Electric Company Space Division King of Prussia, Pa. ABSTRACT A heat activated heat pump (HAHP for space heating since it directly utilizes the engine waste heat in addition to the energy obtained

Oak Ridge National Laboratory

344

Numerical Investigation of Flow and Heat Transfer Characteristics in Rectangular Channels (AR=4:1) with Circular and Elliptical Pin Fin Arrays  

E-Print Network [OSTI]

with six rows of pin ns : 19 viii LIST OF FIGURES FIGURE Page 1 Cooling techniques used in a modern turbine blade (Han et al. [1]) : 3 2 Pin n shapes and their relative dimensions : : : : : : : : : : : : : : 16 3 Schematic of the test section... into two categories, external cooling and internal cooling. External cooling is also known as lm cooling. It is achieved by discharging the internal coolant air through discrete holes in the turbine walls to provide an insulating coolant lm which...

Velichala, Abhishek

2012-07-16T23:59:59.000Z

345

Transient Thermal, Hydraulic, and Mechanical Analysis of a Counter Flow Offset Strip Fin Intermediate Heat Exchanger using an Effective Porous Media Approach  

E-Print Network [OSTI]

state temperature distribution using the effectiveness-NTUanalyzed using the effectiveness-NTU (number of transferand the analytical effectiveness-NTU method verifies that

Urquiza, Eugenio

2009-01-01T23:59:59.000Z

346

Obtaining closure for a plane fin heat sink with elliptic scale-roughened surfaces for Volume Averaging Theory (VAT) based modeling  

E-Print Network [OSTI]

layer, Journal of Fluids Engineering 117 (1995) 181e188. [medium, Journal of Fluids Engineering 121 (1999) 427e433. [Fluid mechanical description of ?uidized beds. Equations of motion, Industrial & Engineering

Zhou, Feng; Catton, Ivan

2013-01-01T23:59:59.000Z

347

Sheet metal stamping die design for warm forming  

DOE Patents [OSTI]

In metal stamping dies, by taking advantage of improved material flow by selectively warming the die, flat sections of the die can contribute to the flow of material throughout the workpiece. Local surface heating can be accomplished by placing a heating block in the die. Distribution of heating at the flat lower train central regions outside of the bend region allows a softer flow at a lower stress to enable material flow into the thinner, higher strain areas at the bend/s. The heating block is inserted into the die and is powered by a power supply.

Ghosh, Amit K. (Ann Arbor, MI)

2003-04-22T23:59:59.000Z

348

Indirect passive cooling system for liquid metal cooled nuclear reactors  

DOE Patents [OSTI]

A liquid metal cooled nuclear reactor having a passive cooling system for removing residual heat resulting from fuel decay during reactor shutdown. The passive cooling system comprises a plurality of partitions surrounding the reactor vessel in spaced apart relation forming intermediate areas for circulating heat transferring fluid which remove and carry away heat from the reactor vessel. The passive cooling system includes a closed primary fluid circuit through the partitions surrounding the reactor vessel and a partially adjoining secondary open fluid circuit for carrying transferred heat out into the atmosphere.

Hunsbedt, Anstein (Los Gatos, CA); Boardman, Charles E. (Saratoga, CA)

1990-01-01T23:59:59.000Z

349

Metal buildings study: performance of materials and field validation  

SciTech Connect (OSTI)

A 5000 square-foot metal building located at Brookhaven National Laboratory has been monitored over a winter season. Energy flows through wall sections were monitored using portable calorimeters. Air infiltration was measured using perfluorocarbon tracers, and the associated heat losses were calculated. Slab losses were assessed through a comparison of measured temperature gradients with results obtained through the use of heat-flow meters. The effect of thermal bridges and compressed insulation in locations where support beams are joined to the exterior skin was found to increase heat losses significantly. A retrofit strategy including spray insulation of beams is projected to save 30% on heating energy.

Loss, W.

1987-12-01T23:59:59.000Z

350

Method for the continuous processing of hermetic fiber optic components and the resultant fiber optic-to-metal components  

DOE Patents [OSTI]

Hermetic fiber optic-to-metal components and method for making hermetic fiber optic-to-metal components by assembling and fixturing elements comprising a metal shell, a glass preform, and a metal-coated fiber optic into desired relative positions and then sealing said fixtured elements preferably using a continuous heating process. The resultant hermetic fiber optic-to-metal components exhibit high hermeticity and durability despite the large differences in thermal coefficients of expansion among the various elements.

Kramer, Daniel P. (Centerville, OH)

1994-08-09T23:59:59.000Z

351

Method for recovering metals from waste  

DOE Patents [OSTI]

A method is described for recovering metals from metals-containing wastes, and vitrifying the remainder of the wastes for disposal. Metals-containing wastes such as circuit boards, cathode ray tubes, vacuum tubes, transistors and so forth, are broken up and placed in a suitable container. The container is heated by microwaves to a first temperature in the range of approximately 300--800 C to combust organic materials in the waste, then heated further to a second temperature in the range of approximately 1,000--1,550 C at which temperature glass formers present in the waste will cause it to melt and vitrify. Low-melting-point metals such as tin and aluminum can be recovered after organics combustion is substantially complete. Metals with higher melting points, such as gold, silver and copper, can be recovered from the solidified product or separated from the waste at their respective melting points. Network former-containing materials can be added at the start of the process to assist vitrification. 2 figs.

Wicks, G.G.; Clark, D.E.; Schulz, R.L.

1998-12-01T23:59:59.000Z

352

Heavy metal biosensor  

DOE Patents [OSTI]

Compositions and methods are provided for detection of certain heavy metals using bacterial whole cell biosensors.

Hillson, Nathan J; Shapiro, Lucille; Hu, Ping; Andersen, Gary L

2014-04-15T23:59:59.000Z

353

Heat pump system  

DOE Patents [OSTI]

An air heating and cooling system for a building includes an expansion type refrigeration circuit and a vapor power circuit. The refrigeration circuit includes two heat exchangers, one of which is communicated with a source of indoor air from the building and the other of which is communicated with a source of air from outside the building. The vapor power circuit includes two heat exchangers, one of which is disposed in series air flow relationship with the indoor refrigeration circuit heat exchanger and the other of which is disposed in series air flow relationship with the outdoor refrigeration circuit heat exchanger. Fans powered by electricity generated by a vapor power circuit alternator circulate indoor air through the two indoor heat exchangers and circulate outside air through the two outdoor heat exchangers. The system is assembled as a single roof top unit, with a vapor power generator and turbine and compressor thermally insulated from the heat exchangers, and with the indoor heat exchangers thermally insulated from the outdoor heat exchangers.

Swenson, Paul F. (Shaker Heights, OH); Moore, Paul B. (Fedhaven, FL)

1983-01-01T23:59:59.000Z

354

Policies supporting Heat Pump Technologies  

E-Print Network [OSTI]

Policies supporting Heat Pump Technologies in Canada IEA Heat Pump Workshop London, UK November 13 in the world, with an average of 16,995 kilowatt-hours per annum. #12;Canada's Context for Heat Pumps Impacts avenues: Ground source heat pumps for cold climates (heating and cooling) Reversible air source heat

Oak Ridge National Laboratory

355

Trending: Metal Oxo Bonds  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Trending: Metal Oxo Bonds Print Trending: Metal Oxo Bonds Print Metal oxides are important for scientific and technical applications in a variety of disciplines, including materials science, chemistry, and biology. Highly covalent metal-oxygen multiple bonds (metal oxos) are the building blocks of metal oxides and have a bearing on the oxide's desirable chemical, magnetic, electronic, and thermal properties. The lack of a more sophisticated grasp of bonding in metal oxides constitutes a roadblock to innovation in a wide variety of important emergent technologies, including industrial catalysis, biomimetic transformations, and artificial photosynthesis. To address this problem, a research team from four national laboratories, three Department of Energy synchrotron user facilities, and the University of Washington has applied spectroscopic and computational analyses to a number of metal oxides, quantifying trends in metal oxo bonding for groups of metals across the periodic table.

356

Trending: Metal Oxo Bonds  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Trending: Metal Oxo Bonds Print Trending: Metal Oxo Bonds Print Metal oxides are important for scientific and technical applications in a variety of disciplines, including materials science, chemistry, and biology. Highly covalent metal-oxygen multiple bonds (metal oxos) are the building blocks of metal oxides and have a bearing on the oxide's desirable chemical, magnetic, electronic, and thermal properties. The lack of a more sophisticated grasp of bonding in metal oxides constitutes a roadblock to innovation in a wide variety of important emergent technologies, including industrial catalysis, biomimetic transformations, and artificial photosynthesis. To address this problem, a research team from four national laboratories, three Department of Energy synchrotron user facilities, and the University of Washington has applied spectroscopic and computational analyses to a number of metal oxides, quantifying trends in metal oxo bonding for groups of metals across the periodic table.

357

Trending: Metal Oxo Bonds  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Trending: Metal Oxo Bonds Print Trending: Metal Oxo Bonds Print Metal oxides are important for scientific and technical applications in a variety of disciplines, including materials science, chemistry, and biology. Highly covalent metal-oxygen multiple bonds (metal oxos) are the building blocks of metal oxides and have a bearing on the oxide's desirable chemical, magnetic, electronic, and thermal properties. The lack of a more sophisticated grasp of bonding in metal oxides constitutes a roadblock to innovation in a wide variety of important emergent technologies, including industrial catalysis, biomimetic transformations, and artificial photosynthesis. To address this problem, a research team from four national laboratories, three Department of Energy synchrotron user facilities, and the University of Washington has applied spectroscopic and computational analyses to a number of metal oxides, quantifying trends in metal oxo bonding for groups of metals across the periodic table.

358

Trending: Metal Oxo Bonds  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Trending: Metal Oxo Bonds Print Trending: Metal Oxo Bonds Print Metal oxides are important for scientific and technical applications in a variety of disciplines, including materials science, chemistry, and biology. Highly covalent metal-oxygen multiple bonds (metal oxos) are the building blocks of metal oxides and have a bearing on the oxide's desirable chemical, magnetic, electronic, and thermal properties. The lack of a more sophisticated grasp of bonding in metal oxides constitutes a roadblock to innovation in a wide variety of important emergent technologies, including industrial catalysis, biomimetic transformations, and artificial photosynthesis. To address this problem, a research team from four national laboratories, three Department of Energy synchrotron user facilities, and the University of Washington has applied spectroscopic and computational analyses to a number of metal oxides, quantifying trends in metal oxo bonding for groups of metals across the periodic table.

359

Large eddy simulation for predicting turbulent heat transfer in gas turbines  

Science Journals Connector (OSTI)

...predicting turbulent heat transfer in gas turbines Danesh K. Tafti Long He K. Nagendra...of propulsion and power generation gas turbines. Accurate prediction of blade metal...compressed bypass air and allow higher turbine inlet temperature, increasing fuel efficiency...

2014-01-01T23:59:59.000Z

360

Fluidized bed heat treating system  

DOE Patents [OSTI]

Systems for heat treating materials are presented. The systems typically involve a fluidized bed that contains granulated heat treating material. In some embodiments a fluid, such as an inert gas, is flowed through the granulated heat treating medium, which homogenizes the temperature of the heat treating medium. In some embodiments the fluid may be heated in a heating vessel and flowed into the process chamber where the fluid is then flowed through the granulated heat treating medium. In some embodiments the heat treating material may be liquid or granulated heat treating material and the heat treating material may be circulated through a heating vessel into a process chamber where the heat treating material contacts the material to be heat treated. Microwave energy may be used to provide the source of heat for heat treating systems.

Ripley, Edward B; Pfennigwerth, Glenn L

2014-05-06T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Flameless heat generator  

SciTech Connect (OSTI)

A heating device generates heat by working a liquid in a closed container with a rotating stack of finely perforate square plates and recovering the heat from the thus heated liquid. In one embodiment a stack of a multiplicity of flat square plates radially offset one from another is rotated in an oil bath in a container under an inner perforate non-rotating cover over which is a similar non-rotating cover that is imperforate. The thermal energy developed through the mechanical working of the liquid is transferred to the main liquid bath and is then removed, as for example, by circulating air or a liquid around the outside of the container with the thus heated air or liquid being used to heat a house or the like.

Leary, C. L.; Leary, G. C.

1983-12-13T23:59:59.000Z

362

Diffusion-Welded Microchannel Heat Exchanger for Industrial Processes  

SciTech Connect (OSTI)

The goal of next generation reactors is to increase energy ef?ciency in the production of electricity and provide high-temperature heat for industrial processes. The ef?cient transfer of energy for industrial applications depends on the ability to incorporate effective heat exchangers between the nuclear heat transport system and the industrial process. The need for ef?ciency, compactness, and safety challenge the boundaries of existing heat exchanger technology. Various studies have been performed in attempts to update the secondary heat exchanger that is downstream of the primary heat exchanger, mostly because its performance is strongly tied to the ability to employ more ef?cient industrial processes. Modern compact heat exchangers can provide high compactness, a measure of the ratio of surface area-to-volume of a heat exchange. The microchannel heat exchanger studied here is a plate-type, robust heat exchanger that combines compactness, low pressure drop, high effectiveness, and the ability to operate with a very large pressure differential between hot and cold sides. The plates are etched and thereafter joined by diffusion welding, resulting in extremely strong all-metal heat exchanger cores. After bonding, any number of core blocks can be welded together to provide the required ?ow capacity. This study explores the microchannel heat exchanger and draws conclusions about diffusion welding/bonding for joining heat exchanger plates, with both experimental and computational modeling, along with existing challenges and gaps. Also, presented is a thermal design method for determining overall design speci?cations for a microchannel printed circuit heat exchanger for both supercritical (24 MPa) and subcritical (17 MPa) Rankine power cycles.

Piyush Sabharwall; Denis E. Clark; Michael V. Glazoff; Michael G. McKellar; Ronald E. Mizia

2013-03-01T23:59:59.000Z

363

Mechanical Compression Heat Pumps  

E-Print Network [OSTI]

MECHANICAL COMPRESSION HEAT PUMPS Thomas-L. Apaloo and K. Kawamura Mycom Corporation, Los Angeles, California J. Matsuda, Mayekawa Mfg. Co., Tokyo, Japan ABSTRACT Mechanical compression heat pumping is not new in industrial applications.... In fact, industry history suggests that the theoretical concept was developed before 1825. Heat pump manufacturers gained the support of consultants and end-users when the energy crisis hit this country in 1973. That interest, today, has been...

Apaloo, T. L.; Kawamura, K.; Matsuda, J.

364

Sorption heat engines  

E-Print Network [OSTI]

For a simple free energy generating device - driven by thermal cycling and based on alternating adsorption and desorption - that has not been explicitly recognized as heat engine the name sorption heat engine is proposed. The mechanism is generally applicable to the fields of physics, chemistry, geology, and possibly, if relevant to the origin of life, biology. Four kinds of sorption heat engines are distinguished depending on the occurrence of changes in composition of the adsorbent or adsorbate during the thermal cycle.

Muller, A W J; Muller, Anthonie W. J.; Schulze-Makuch, Dirk

2005-01-01T23:59:59.000Z

365

This is an earlier view of the accepted manuscript for the article "Fish fins as non-lethal surrogates for muscle tissues in freshwater food web studies using stable  

E-Print Network [OSTI]

This is an earlier view of the accepted manuscript for the article "Fish fins as non- lethal is available at http://onlinelibrary.wiley.com/doi/10.1002/rcm.6265/abstract. Fish fins as non-muscle relationships for 14 European freshwater fish species Nicolas Hette-Tronquart*a , Laurent Mazeasa , Liana

Boyer, Edmond

366

Combined Heat and Power  

Office of Environmental Management (EM)

energy costs and 31 emissions while also providing more resilient and reliable electric power and thermal energy 1 . CHP 32 systems combine the production of heat (for both...

367

Waste Heat Recovery  

Office of Environmental Management (EM)

DRAFT - PRE-DECISIONAL - DRAFT 1 Waste Heat Recovery 1 Technology Assessment 2 Contents 3 1. Introduction to the TechnologySystem ......

368

Solar Heating in Uppsala.  

E-Print Network [OSTI]

?? The housing corporation Uppsalahem has installed asolar heating system in the neighbourhood Haubitsen,which was renovated in 2011. This report examineshow much energy the solar… (more)

Blomqvist, Emelie; Häger, Klara

2012-01-01T23:59:59.000Z

369

HEATS: Thermal Energy Storage  

SciTech Connect (OSTI)

HEATS Project: The 15 projects that make up ARPA-E’s HEATS program, short for “High Energy Advanced Thermal Storage,” seek to develop revolutionary, cost-effective ways to store thermal energy. HEATS focuses on 3 specific areas: 1) developing high-temperature solar thermal energy storage capable of cost-effectively delivering electricity around the clock and thermal energy storage for nuclear power plants capable of cost-effectively meeting peak demand, 2) creating synthetic fuel efficiently from sunlight by converting sunlight into heat, and 3) using thermal energy storage to improve the driving range of electric vehicles (EVs) and also enable thermal management of internal combustion engine vehicles.

None

2012-01-01T23:59:59.000Z

370

Solar heating in Colombia.  

E-Print Network [OSTI]

?? This report describes the process of a thesis implemented in Colombia concerning solar energy. The project was to install a self-circulating solar heating system,… (more)

Skytt, Johanna

2012-01-01T23:59:59.000Z

371

Photovoltaic roof heat flux  

E-Print Network [OSTI]

Effect of building integrated photovoltaics on microclimateof a building's integrated-photovoltaics on heating a n dgaps for building- integrated photovoltaics, Solar Energy

Samady, Mezhgan Frishta

2011-01-01T23:59:59.000Z

372

Passive solar space heating  

SciTech Connect (OSTI)

An overview of passive solar space heating is presented indicating trends in design, new developments, performance measures, analytical design aids, and monitored building results.

Balcomb, J.D.

1980-01-01T23:59:59.000Z

373

Combined Heat & Power  

Broader source: Energy.gov (indexed) [DOE]

available today." -American Council for an Energy-Efficient Economy What is Combined Heat & Power (CHP)? Federal Utility Partnership Working Group May 7 - 8, 2014 Virginia...

374

Heat transfer dynamics  

SciTech Connect (OSTI)

As heat transfer technology increases in complexity, it becomes more difficult for those without thermal dynamics engineering training to choose between competitive heat transfer systems offered to meet their drying requirements. A step back to the basics of heat transfer can help professional managers and papermakers make informed decisions on alternative equipment and methods. The primary forms of heat and mass transfer are reviewed with emphasis on the basics, so a practical understanding of each is gained. Finally, the principles and benefits of generating infrared energy by combusting a gaseous hydrocarbon fuel are explained.

Smith, T.M. (Marsden, Inc., Pennsauken, NJ (United States))

1994-08-01T23:59:59.000Z

375

ARM - Atmospheric Heat Budget  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

ListAtmospheric Heat Budget Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About...

376

Metal Organic Heat Carriers for Enhanced Geothermal Systems  

Broader source: Energy.gov [DOE]

DOE Geothermal Program Peer Review 2010 - Presentation. This project addresses Energy Conversion Barrier N -Inability to lower the temperature conditions under which EGS power generation is commercially viable.

377

Heat Pumps | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Heat Pumps Heat Pumps Heat Pumps Geothermal heat pumps are expensive to install but pay for themselves over time in reduced heating and cooling costs. Learn more about how geothermal heat pumps heat and cool buildings by concentrating the naturally existing heat contained within the earth -- a clean, reliable, and renewable source of energy. In moderate climates, heat pumps can be an energy-efficient alternative to furnaces and air conditioners. Several types of heat pumps are available, including air-source; geothermal; ductless, mini-split; and absorption heat pumps. Learn more about the different options and how to use your heat pump efficiently to save money and energy at home. Featured Heat Pump Systems A heat pump can provide an alternative to using your air conditioner. | Photo courtesy of iStockPhoto/LordRunar.

378

HEAT RECOVERY FROM WASTE WATER BY MEANS OF A RECUPERATIVE HEAT EXCHANGER AND A HEAT PUMP  

Science Journals Connector (OSTI)

ABSTRACT The useful heat of warm waste water is generally transferred to cold water using a recuperative heat exchanger. Depending on its design, the heat exchanger is able to utilise up to 90% of the waste heat potential available. The electric energy needed to operate such a system is more than compensated for by an approximately 50-fold gain of useful heat. To increase substantially the waste heat potential available and the amount of heat recovered, the system for recuperative heat exchange can be complemented by a heat pump. Such a heat recovery system on the basis of waste water is being operated in a public indoor swimming pool. Here the recuperative heat exchanger accounts for about 60%, the heat pump for about 40% of the toal heat reclaimed. The system consumes only 1 kWh of electric energy to supply 8 kWh of useful heat. In this way the useful heat of 8 kWh is compensated for by the low consumption of primary energy of 2.8 kWh. Due to the installation of an automatic cleaning device, the heat transfer surfaces on the waste water side avoid deposits so that the troublesome maintenance work required in other cases on the heat exchangers is not required. KEYWORDS Shower drain water, recuperative heat recovery, heat recovery by means of a heat pump, combination of both types of heat recovery, automatic cleaning device for the heat exchangers, ratio of useful heat supply vs. electric energy consumption, economic consideration.

K. Biasin; F.D. Heidt

1988-01-01T23:59:59.000Z

379

Carbide and carbonitride surface treatment method for refractory metals  

DOE Patents [OSTI]

A carbide and carbonitride surface treatment method for refractory metals is provided, in steps including, heating a part formed of boron, chromium, hafnium, molybdenum, niobium, tantalum, titanium, tungsten or zirconium, or alloys thereof, in an evacuated chamber and then introducing reaction gases including nitrogen and hydrogen, either in elemental or water vapor form, which react with a source of elemental carbon to form carbon-containing gaseous reactants which then react with the metal part to form the desired surface layer. Apparatus for practicing the method is also provided, in the form of a carbide and carbonitride surface treatment system including a reaction chamber, a source of elemental carbon, a heating subassembly and a source of reaction gases. Alternative methods of providing the elemental carbon and the reaction gases are provided, as well as methods of supporting the metal part, evacuating the chamber with a vacuum subassembly and heating all of the components to the desired temperature. 5 figs.

Meyer, G.A.; Schildbach, M.A.

1996-12-03T23:59:59.000Z

380

Method for forming metallic silicide films on silicon substrates by ion beam deposition  

SciTech Connect (OSTI)

This patent describes metallic silicide films formed on silicon substrates by contacting the substrates with a low-energy ion beam of metal ions while moderately heating the substrate. The heating of the substrate provides for the diffusion of silicon atoms through the film as it is being formed to the surface of the film for interaction with the metal ions as they contact the diffused silicon. The metallic silicide films provided by the invention are contaminant free, of uniform stoichiometry, large grain size, and exhibit low resistivity values which are of particular usefulness for integrated circuit production.

Zuhr, R.A.; Holland, O.W.

1990-03-13T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Method for forming metallic silicide films on silicon substrates by ion beam deposition  

DOE Patents [OSTI]

Metallic silicide films are formed on silicon substrates by contacting the substrates with a low-energy ion beam of metal ions while moderately heating the substrate. The heating of the substrate provides for the diffusion of silicon atoms through the film as it is being formed to the surface of the film for interaction with the metal ions as they contact the diffused silicon. The metallic silicide films provided by the present invention are contaminant free, of uniform stoichiometry, large grain size, and exhibit low resistivity values which are of particular usefulness for integrated circuit production.

Zuhr, Raymond A. (Oak Ridge, TN); Holland, Orin W. (Oak Ridge, TN)

1990-01-01T23:59:59.000Z

382

Method for forming metallic silicide films on silicon substrates by ion beam deposition  

SciTech Connect (OSTI)

Metallic silicide films are formed on silicon substrates by contacting the substrates with a low-energy ion beam of metal ions while moderately heating the substrate. The heating of the substrate provides for the diffusion of silicon atoms through the film as it is being formed to the surface of the film for interaction with the metal ions as they contact the diffused silicon. The metallic silicide films provided by the present invention are contaminant free, of uniform stoichiometry, large grain size, and exhibit low resistivity values which are of particular usefulness for integrated circuit production.

Zuhr, R.A.; Holland, O.W.

1989-01-24T23:59:59.000Z

383

Waste Heat Recovery from Industrial Process Heating Equipment -  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Waste Heat Recovery from Industrial Process Heating Equipment - Waste Heat Recovery from Industrial Process Heating Equipment - Cross-cutting Research and Development Priorities Speaker(s): Sachin Nimbalkar Date: January 17, 2013 - 11:00am Location: 90-2063 Seminar Host/Point of Contact: Aimee McKane Waste heat is generated from several industrial systems used in manufacturing. The waste heat sources are distributed throughout a plant. The largest source for most industries is exhaust / flue gases or heated air from heating systems. This includes the high temperature gases from burners in process heating, lower temperature gases from heat treat, dryers, and heaters, heat from heat exchangers, cooling liquids and gases etc. The previous studies and direct contact with the industry as well as equipment suppliers have shown that a large amount of waste heat is not

384

Microchannel crossflow fluid heat exchanger and method for its fabrication  

DOE Patents [OSTI]

A microchannel crossflow fluid heat exchanger and a method for its fabrication are disclosed. The heat exchanger is formed from a stack of thin metal sheets which are bonded together. The stack consists of alternating slotted and unslotted sheets. Each of the slotted sheets includes multiple parallel slots which form fluid flow channels when sandwiched between the unslotted sheets. Successive slotted sheets in the stack are rotated ninety degrees with respect to one another so as to form two sets of orthogonally extending fluid flow channels which are arranged in a crossflow configuration. The heat exchanger has a high surface to volume ratio, a small dead volume, a high heat transfer coefficient, and is suitable for use with fluids under high pressures. The heat exchanger has particular application in a Stirling engine that utilizes a liquid as the working substance. 9 figs.

Swift, G.W.; Migliori, A.; Wheatley, J.C.

1985-05-14T23:59:59.000Z

385

Microchannel crossflow fluid heat exchanger and method for its fabrication  

DOE Patents [OSTI]

A microchannel crossflow fluid heat exchanger and a method for its fabrication are disclosed. The heat exchanger is formed from a stack of thin metal sheets which are bonded together. The stack consists of alternating slotted and unslotted sheets. Each of the slotted sheets includes multiple parallel slots which form fluid flow channels when sandwiched between the unslotted sheets. Successive slotted sheets in the stack are rotated ninety degrees with respect to one another so as to form two sets of orthogonally extending fluid flow channels which are arranged in a crossflow configuration. The heat exchanger has a high surface to volume ratio, a small dead volume, a high heat transfer coefficient, and is suitable for use with fluids under high pressures. The heat exchanger has particular application in a Stirling engine that utilizes a liquid as the working substance.

Swift, G.W.; Migliori, A.; Wheatley, J.C.

1982-08-31T23:59:59.000Z

386

Quantal Heating of Conducting Electrons with Discrete Spectrum  

SciTech Connect (OSTI)

Usually heating of conducting electrons by dc electric field results in an increase of electron temperature. In this paper we show that the dc heating of 2D electrons, placed in quantized magnetic fields, results in a peculiar electron distribution, which has the same broadening or an effective 'temperature' as the unbiased electron system. The quantal heating, however, violates strongly the Ohm's Law. In the conducting system with discrete electron spectrum the quantal heating results in spectacular decrease of electron resistance and transition of the electrons into a state with zero differential resistance (ZDR). Finally the heating leads to apparent dc driven metal-insulator transition, which correlates with the transition into the ZDR state. The correlation is very unexpected and is not understood.

Vitkalov, S. A. [Department of Physics, The City College of New York, New York, NY 10031 (United States); Bykov, A. A. [Institute of Semiconductor Physics, 630090 Novosibirsk (Russian Federation)

2011-12-23T23:59:59.000Z

387

Total Space Heating Water Heating Cook-  

Gasoline and Diesel Fuel Update (EIA)

Released: September, 2008 Released: September, 2008 Total Space Heating Water Heating Cook- ing Other Total Space Heating Water Heating Cook- ing Other All Buildings* ........................... 1,870 1,276 322 138 133 43.0 29.4 7.4 3.2 3.1 Building Floorspace (Square Feet) 1,001 to 5,000 ........................... 243 151 34 40 18 78.7 48.9 11.1 13.0 5.7 5,001 to 10,000 .......................... 202 139 31 29 Q 54.8 37.6 8.5 7.9 Q 10,001 to 25,000 ........................ 300 240 31 21 7 42.5 34.1 4.4 3.0 1.1 25,001 to 50,000 ........................ 250 182 40 11 Q 41.5 30.2 6.6 1.9 Q 50,001 to 100,000 ...................... 236 169 41 8 19 35.4 25.2 6.2 1.2 2.8 100,001 to 200,000 .................... 241 165 54 7 16 36.3 24.8 8.1 1.0 2.4 200,001 to 500,000 .................... 199 130 42 11 16 35.0 22.8 7.5 1.9 2.8 Over 500,000 ............................. 198

388

Total Space Heating Water Heating Cook-  

Gasoline and Diesel Fuel Update (EIA)

Released: September, 2008 Released: September, 2008 Total Space Heating Water Heating Cook- ing Other Total Space Heating Water Heating Cook- ing Other All Buildings ............................. 2,037 1,378 338 159 163 42.0 28.4 7.0 3.3 3.4 Building Floorspace (Square Feet) 1,001 to 5,000 ........................... 249 156 35 41 18 78.6 49.1 11.0 12.9 5.6 5,001 to 10,000 .......................... 218 147 32 31 7 54.8 37.1 8.1 7.9 1.7 10,001 to 25,000 ........................ 343 265 34 25 18 43.8 33.9 4.4 3.2 2.3 25,001 to 50,000 ........................ 270 196 41 13 Q 40.9 29.7 6.3 2.0 2.9 50,001 to 100,000 ...................... 269 186 45 13 24 35.8 24.8 6.0 1.8 3.2 100,001 to 200,000 .................... 267 182 56 10 19 35.4 24.1 7.4 1.3 2.6 200,001 to 500,000 .................... 204 134 43 11 17 34.7 22.7 7.3 1.8 2.9 Over 500,000 .............................

389

Steady response to heating: Gaussian heat source  

E-Print Network [OSTI]

+ prescribed latent heating => "Matsuno-Gill model" Moisture equation for precipitation term ¡ Can make. of Equatorial Waves Filter out "background spectrum": ¡ Can see all different wave types! Especially Kelvin #12;Equatorial Waves Alternative theory for wave speed: ¡ Higher vertical mode structure causes phase

Frierson, Dargan

390

Cooking utensil with improved heat retention  

DOE Patents [OSTI]

A cooking utensil with improved heat retention includes an inner pot received within an outer pot and separated in a closely spaced-apart relationship to form a volume or chamber therebetween. The chamber is evacuated and sealed with foil leaves at the upper edges of the inner and outer pot. The vacuum created between the inner and outer pot, along with the minimum of thermal contact between the inner and outer pot, and the reduced radiative heat transfer due to low emissivity coatings on the inner and outer pot, provide for a highly insulated cooking utensil. Any combination of a plurality of mechanisms for selectively disabling and re-enabling the insulating properties of the pot are provided within the chamber. These mechanisms may include: a hydrogen gas producing and reabsorbing device such as a metal hydride, a plurality of metal contacts which can be adjusted to bridge the gap between the inner and outer pot, and a plurality of bimetallic switches which can selectively bridge the gap between the inner and outer pot. In addition, phase change materials with superior heat retention characteristics may be provided within the cooking utensil. Further, automatic and programmable control of the cooking utensil can be provided through a microprocessor and associated hardware for controlling the vacuum disable/enable mechanisms to automatically cook and save food.

Potter, Thomas F. (Denver, CO); Benson, David K. (Golden, CO); Burch, Steven D. (Golden, CO)

1997-01-01T23:59:59.000Z

391

Metal-Air Batteries  

SciTech Connect (OSTI)

Metal-air batteries have much higher specific energies than most currently available primary and rechargeable batteries. Recent advances in electrode materials and electrolytes, as well as new designs on metal-air batteries, have attracted intensive effort in recent years, especially in the development of lithium-air batteries. The general principle in metal-air batteries will be reviewed in this chapter. The materials, preparation methods, and performances of metal-air batteries will be discussed. Two main metal-air batteries, Zn-air and Li-air batteries will be discussed in detail. Other type of metal-air batteries will also be described.

Zhang, Jiguang; Bruce, Peter G.; Zhang, Gregory

2011-08-01T23:59:59.000Z

392

Proceedings of Heat Transfer 2003: ASME Summer Heat Transfer Conference  

E-Print Network [OSTI]

Proceedings of Heat Transfer 2003: ASME Summer Heat Transfer Conference Las Vegas, Nevada, USA July 21-23, 2003 HT2003-47449 HEAT TRANSFER FROM A MOVING AND EVAPORATING MENISCUS ON A HEATED SURFACE meniscus with complete evaporation of water without any meniscus break-up. The experimental heat transfer

Kandlikar, Satish

393

Heat pipe based passive emergency core cooling system for safe shutdown of nuclear power reactor  

Science Journals Connector (OSTI)

Abstract On March 11th, 2011, a natural disaster created by earthquakes and Tsunami caused a serious potential of nuclear reactor meltdown in Fukushima due to the failure of Emergency Core Cooling System (ECCS) powered by diesel generators. In this paper, heat pipe based ECCS has been proposed for nuclear power plants. The designed loop type heat pipe ECCS is composed of cylindrical evaporator with 62 vertical tubes, each 150 mm diameter and 6 m length, mounted around the circumference of nuclear fuel assembly and 21 m × 10 m × 5 m naturally cooled finned condenser installed outside the primary containment. Heat pipe with overall thermal resistance of 1.44 × 10?5 °C/W will be able to reduce reactor temperature from initial working temperature of 282 °C to below 250 °C within 7 h. The overall ECCS also includes feed water flooding of the core using elevated water tank for initial 10 min which will accelerate cooling of the core, replenish core coolant during loss of coolant accident and avoids heat transfer crisis phenomena during heat pipe start-up process. The proposed heat pipe system will operate in fully passive mode with high runtime reliability and therefore provide safer environment to nuclear power plants.

Masataka Mochizuki; Randeep Singh; Thang Nguyen; Tien Nguyen

2014-01-01T23:59:59.000Z

394

Chemical heat pump  

DOE Patents [OSTI]

A chemical heat pump system is disclosed for use in heating and cooling structures such as residences or commercial buildings. The system is particularly adapted to utilizing solar energy, but also increases the efficiency of other forms of thermal energy when solar energy is not available. When solar energy is not available for relatively short periods of time, the heat storage capacity of the chemical heat pump is utilized to heat the structure, as during nighttime hours. The design also permits home heating from solar energy when the sun is shining. The entire system may be conveniently rooftop located. In order to faciliate installation on existing structures, the absorber and vaporizer portions of the system may each be designed as flat, thin wall, thin pan vessels which materially increase the surface area available for heat transfer. In addition, this thin, flat configuration of the absorber and its thin walled (and therefore relatively flexible) construction permits substantial expansion and contraction of the absorber material during vaporization and absorption without generating voids which would interfere with heat transfer.

Greiner, Leonard (2853-A Hickory Pl., Costa Mesa, CA 92626)

1984-01-01T23:59:59.000Z

395

Chemical heat pump  

DOE Patents [OSTI]

A chemical heat pump system is disclosed for use in heating and cooling structures such as residences or commercial buildings. The system is particularly adapted to utilizing solar energy, but also increases the efficiency of other forms of thermal energy when solar energy is not available. When solar energy is not available for relatively short periods of time, the heat storage capacity of the chemical heat pump is utilized to heat the structure, as during nighttime hours. The design also permits home heating from solar energy when the sun is shining. The entire system may be conveniently rooftop located. In order to facilitate installation on existing structures, the absorber and vaporizer portions of the system may each be designed as flat, thin wall, thin pan vessels which materially increase the surface area available for heat transfer. In addition, this thin, flat configuration of the absorber and its thin walled (and therefore relatively flexible) construction permits substantial expansion and contraction of the absorber material during vaporization and absorption without generating voids which would interfere with heat transfer.

Greiner, Leonard (2853-A Hickory Pl., Costa Mesa, CA 92626)

1984-01-01T23:59:59.000Z

396

Chemical heat pump  

DOE Patents [OSTI]

A chemical heat pump system is disclosed for use in heating and cooling structures such as residences or commercial buildings. The system is particularly adapted to utilizing solar energy, but also increases the efficiency of other forms of thermal energy when solar energy is not available. When solar energy is not available for relatively short periods of time, the heat storage capacity of the chemical heat pump is utilized to heat the structure, as during nighttime hours. The design also permits home heating from solar energy when the sun is shining. The entire system may be conveniently rooftop located. In order to facilitate intallation on existing structures, the absorber and vaporizer portions of the system may each be designed as flat, thin wall, thin pan vessels which materially increase the surface area available for heat transfer. In addition, this thin, flat configuration of the absorber and its thin walled (and therefore relatively flexible) construction permits substantial expansion and contraction of the absorber material during vaporization and absorption without generating voids which would interfere with heat transfer.

Greiner, Leonard (2853-A Hickory Pl., Costa Mesa, CA 92626)

1984-01-01T23:59:59.000Z

397

Chemical heat pump  

DOE Patents [OSTI]

A chemical heat pump system is disclosed for use in heating and cooling structures such as residences or commercial buildings. The system is particularly adapted to utilizing solar energy, but also increases the efficiency of other forms of thermal energy when solar energy is not available. When solar energy is not available for relatively short periods of time, the heat storage capacity of the chemical heat pump is utilized to heat the structure, as during nighttime hours. The design also permits home heating from solar energy when the sun is shining. The entire system may be conveniently rooftop located. In order to facilitate installation on existing structures, the absorber and vaporizer portions of the system may each be designed as flat, thin wall, thin pan vessels which materially increase the surface area available for heat transfer. In addition, this thin, flat configuration of the absorber and its thin walled (and therefore relatively flexible) construction permits substantial expansion and contraction of the absorber material during vaporization and absorption without generating voids which would interfere with heat transfer.

Greiner, Leonard (2853-A Hickory Pl., Costa Mesa, CA 92626)

1981-01-01T23:59:59.000Z

398

Heat Requirements of Buildings  

Science Journals Connector (OSTI)

... and Ventilating Engineers in a publication entitled “Recommendations for the Computation of Heat Requirements for Buildings” (Pp. iii+41. Is. 9d.) This comprises a section of the ... parts. That on temperature-rise and rates of change gives the recommended values applicable to buildings ranging alphabetically from aircraft sheds to warehouses. The design of heating and ventilating installations ...

1942-02-28T23:59:59.000Z

399

Method of nitriding, carburizing, or oxidizing refractory metal articles using microwaves  

DOE Patents [OSTI]

A method of nitriding an article of refractory-nitride-forming metal or metalloids. A consolidated metal or metalloid article is placed inside a microwave oven and nitrogen containing gas is introduced into the microwave oven. The metal or metalloid article is heated to a temperature sufficient to react the metal or metalloid with the nitrogen by applying a microwave energy within the microwave oven. The metal or metalloid article is maintained at that temperature for a period of time sufficient to convert the article of metal or metalloid to an article of refractory nitride. in addition, a method of applying a coating, such as a coating of an oxide, a carbide, or a carbo-nitride, to an article of metal or metalloid by microwave heating.

Holcombe, C.E.; Dykes, N.L.; Tiegs, T.N.

1992-10-13T23:59:59.000Z

400

Method of nitriding, carburizing, or oxidizing refractory metal articles using microwaves  

DOE Patents [OSTI]

A method of nitriding an article of refractory-nitride-forming metal or metalloids. A consolidated metal or metalloid article is placed inside a microwave oven and nitrogen containing gas is introduced into the microwave oven. The metal or metalloid article is heated to a temperature sufficient to react the metal or metalloid with the nitrogen by applying a microwave energy within the microwave oven. The metal or metalloid article is maintained at that temperature for a period of time sufficient to convert the article of metal or metalloid to an article of refractory nitride. in addition, a method of applying a coating, such as a coating of an oxide, a carbide, or a carbo-nitride, to an article of metal or metalloid by microwave heating.

Holcombe, Cressie E. (Knoxville, TN); Dykes, Norman L. (Oak Ridge, TN); Tiegs, Terry N. (Lenoir City, TN)

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

METAL HYDRIDE HYDROGEN COMPRESSORS: A REVIEW  

SciTech Connect (OSTI)

Metal hydride (MH) thermal sorption compression is an efficient and reliable method allowing a conversion of energy from heat into a compressed hydrogen gas. The most important component of such a thermal engine the metal hydride material itself should possess several material features in order to achieve an efficient performance in the hydrogen compression. Apart from the hydrogen storage characteristics important for every solid H storage material (e.g. gravimetric and volumetric efficiency of H storage, hydrogen sorption kinetics and effective thermal conductivity), the thermodynamics of the metal-hydrogen systems is of primary importance resulting in a temperature dependence of the absorption/desorption pressures). Several specific features should be optimized to govern the performance of the MH-compressors including synchronisation of the pressure plateaus for multi-stage compressors, reduction of slope of the isotherms and hysteresis, increase of cycling stability and life time, together with challenges in system design associated with volume expansion of the metal matrix during the hydrogenation. The present review summarises numerous papers and patent literature dealing with MH hydrogen compression technology. The review considers (a) fundamental aspects of materials development with a focus on structure and phase equilibria in the metal-hydrogen systems suitable for the hydrogen compression; and (b) applied aspects, including their consideration from the applied thermodynamic viewpoint, system design features and performances of the metal hydride compressors and major applications.

Bowman Jr, Robert C [ORNL] [ORNL; Yartys, Dr. Volodymyr A. [Institute for Energy Technology (IFE)] [Institute for Energy Technology (IFE); Lototskyy, Dr. Michael V [University of the Western Cape, South Africa] [University of the Western Cape, South Africa; Pollet, Dr. B.G. [University of the Western Cape, South Africa

2014-01-01T23:59:59.000Z

402

Solar heating system  

DOE Patents [OSTI]

An improved solar heating system in which the incident radiation of the sun is absorbed on collector panels, transferred to a storage unit and then distributed as heat for a building and the like. The improvement is obtained by utilizing a storage unit comprising separate compartments containing an array of materials having different melting points ranging from 75.degree. to 180.degree. F. The materials in the storage system are melted in accordance with the amount of heat absorbed from the sun and then transferred to the storage system. An efficient low volume storage system is provided by utilizing the latent heat of fusion of the materials as they change states in storing and releasing heat for distribution.

Schreyer, James M. (Oak Ridge, TN); Dorsey, George F. (Concord, TN)

1982-01-01T23:59:59.000Z

403

Synthesis Of Fluorescent Metal Nanoclusters  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Synthesis Of Fluorescent Metal Nanoclusters Synthesis Of Fluorescent Metal Nanoclusters Fluorescent metal nanoclusters were prepared. Available for thumbnail of Feynman Center...

404

Radiant Heating | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Radiant Heating Radiant Heating Radiant Heating June 24, 2012 - 5:52pm Addthis In-wall radiant heating in a house under construction near Denver. | Photo courtesy of Warren Gretz, NREL. In-wall radiant heating in a house under construction near Denver. | Photo courtesy of Warren Gretz, NREL. Radiant heating systems supply heat directly to the floor or to panels in the wall or ceiling of a house. The systems depend largely on radiant heat transfer -- the delivery of heat directly from the hot surface to the people and objects in the room via infrared radiation. Radiant heating is the effect you feel when you can feel the warmth of a hot stovetop element from across the room. When radiant heating is located in the floor, it is often called radiant floor heating or simply floor heating.

405

Radiant Heating | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Radiant Heating Radiant Heating Radiant Heating June 24, 2012 - 5:52pm Addthis In-wall radiant heating in a house under construction near Denver. | Photo courtesy of Warren Gretz, NREL. In-wall radiant heating in a house under construction near Denver. | Photo courtesy of Warren Gretz, NREL. Radiant heating systems supply heat directly to the floor or to panels in the wall or ceiling of a house. The systems depend largely on radiant heat transfer -- the delivery of heat directly from the hot surface to the people and objects in the room via infrared radiation. Radiant heating is the effect you feel when you can feel the warmth of a hot stovetop element from across the room. When radiant heating is located in the floor, it is often called radiant floor heating or simply floor heating.

406

Bead and Process for Removing Dissolved Metal Contaminants  

SciTech Connect (OSTI)

A bead is provided which comprises or consists essentially of activated carbon immobilized by crosslinked poly (carboxylic acid) binder, sodium silicate binder, or polyamine binder. The bead is effective to remove metal and other ionic contaminants from dilute aqueous solutions. A method of making metal-ion sorbing beads is provided, comprising combining activated carbon, and binder solution (preferably in a pin mixer where it is whipped), forming wet beads, and heating and drying the beads. The binder solution is preferably poly(acrylic acid) and glycerol dissolved in water and the wet beads formed from such binder solution are preferably heated and crosslinked in a convection oven.

Summers, Bobby L., Jr.; Bennett, Karen L.; Foster, Scott A.

2005-01-18T23:59:59.000Z

407

Dissimilar-metal weld failures in boiler tubing  

SciTech Connect (OSTI)

Both ferritic heat-resisting steels and austenitic stainless steels are used for fossil-fired boilers for central power stations. The use of these two different types of materials within the system leads to the need for a dissimilar-metal weld transition joint. Increased cyclic operation of boilers has led to a rash of failures in welds between dissimilar metals; studies have identified the causes, and improved nondestructive testing techniques permit early identification of problem areas.

Klueh, R.L.

1984-02-01T23:59:59.000Z

408

Metal phthalocyanine catalysts  

DOE Patents [OSTI]

As a new composition of matter, alkali metal or ammonium or tetraalkylammonium diazidoperfluorophthalocyanatoferrate. Other embodiments of the invention comprise compositions wherein the metal of the coordination complex is cobalt, manganese and chromium.

Ellis, Jr., Paul E. (Downingtown, PA); Lyons, James E. (Wallingford, PA)

1994-01-01T23:59:59.000Z

409

Liquid Metal Thermal Electric Converter bench test module  

SciTech Connect (OSTI)

This report describes the design, fabrication, and test of a Liquid Metal Thermal Electric Converter Bench Test Module. The work presented in this document was conducted as a part of Heat Engine Task of the US Department of Energy's (DOE) Solar Thermal Technology Program. The objective of this task is the development and evaluation of heat engine technologies applicable to distributed receiver systems, in particular, dish electric systems.

Lukens, L.L.; Andraka, C.E.; Moreno, J.B.

1988-04-01T23:59:59.000Z

410

Elastic Metal Alloy Refrigerants: Thermoelastic Cooling  

SciTech Connect (OSTI)

BEETIT Project: UMD is developing an energy-efficient cooling system that eliminates the need for synthetic refrigerants that harm the environment. More than 90% of the cooling and refrigeration systems in the U.S. today use vapor compression systems which rely on liquid to vapor phase transformation of synthetic refrigerants to absorb or release heat. Thermoelastic cooling systems, however, use a solid-state material—an elastic shape memory metal alloy—as a refrigerant and a solid to solid phase transformation to absorb or release heat. UMD is developing and testing shape memory alloys and a cooling device that alternately absorbs or creates heat in much the same way as a vapor compression system, but with significantly less energy and a smaller operational footprint.

None

2010-10-01T23:59:59.000Z

411

MECS 2006- Fabricated Metals  

Broader source: Energy.gov [DOE]

Manufacturing Energy and Carbon Footprint for Fabricated Metals (NAICS 332) Sector with Total Energy Input, October 2012 (MECS 2006)

412

Heat-Of-Reaction Chemical Heat Pumps--Possible Configurations  

E-Print Network [OSTI]

-807. (5) K. Kesavan. The Use of Dissociating Gases As the Working Fluid in Thermodynamic Power Conversion Cycles, Ph.D. thesis. Carnegie-Mellon University, 1978, Ann Arbor, MI: University Microfilms International, 1978. 5. Heat amplifier with a gas...ABSTRACT Chemical heat pumps utilize working fluids which undergo reversible chemical changes. Mechanically driven reactive heat pump cycles or, alternatively, hl~a: driven heat pumps in which either heat engine or heat pump working fluid...

Kirol, L. D.

413

Chemical heat pump cools as well as heats  

Science Journals Connector (OSTI)

Chemical heat pump cools as well as heats ... Innovative heat pump uses methanol refrigerant, calcium chloride absorber to use and store solar energy for heating, air conditioning, hot water ... Though the EIC heat pump is similar in concept to other chemical heat pumps now being used or developed, it does offer a number of innovations, not the least of which are its novel refrigerant (methanol) and absorption medium (calcium chloride). ...

RON DAGANI

1980-10-20T23:59:59.000Z

414

Deposition of Contiguous Metal Adlayer on Transition Metal Nanostructu...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and Abstract Primary Lab Date Application 20100099012 Application 20100099012 Electrocatalyst Synthesized by Depositing a Contiguous Metal Adlayer on Transition Metal...

415

A coupled theory for diffusion of hydrogen and large elastic-plastic deformations of metals  

E-Print Network [OSTI]

A thermodynamically-consistent coupled-theory which accounts for diffusion of hydrogen, trapping of hydrogen, diffusion of heat, and large elastic-plastic deformations of metals is developed. Our theoretical framework ...

Di Leo, Claudio V

2012-01-01T23:59:59.000Z

416

Laboratory Measurements of Alkali Metal Containing Vapors Released during Biomass Combustion  

Science Journals Connector (OSTI)

Alkali metals, in particular potassium. have been implicated as key ingredients for enhancing fouling and slagging of heat transfer surfaces in power generating facilities that convert biomass to electricity. Whe...

David C. Dayton; Thomas A. Milne

1996-01-01T23:59:59.000Z

417

Pressurized heat treatment of glass ceramic  

DOE Patents [OSTI]

A method of producing a glass-ceramic having a specified thermal expansion value is disclosed. The method includes the step of pressurizing the parent glass material to a predetermined pressure during heat treatment so that the glass-ceramic produced has a specified thermal expansion value. Preferably, the glass-ceramic material is isostatically pressed. A method for forming a strong glass-ceramic to metal seal is also disclosed in which the glass-ceramic is fabricated to have a thermal expansion value equal to that of the metal. The determination of the thermal expansion value of a parent glass material placed in a high-temperature environment is also used to determine the pressure in the environment.

Kramer, D.P.

1984-04-19T23:59:59.000Z

418

City of Klamath Falls District Heating District Heating Low Temperatur...  

Open Energy Info (EERE)

Geothermal Facility Jump to: navigation, search Name City of Klamath Falls District Heating District Heating Low Temperature Geothermal Facility Facility City of Klamath...

419

PIA - Northeast Home Heating Oil Reserve System (Heating Oil...  

Office of Environmental Management (EM)

Home Heating Oil Reserve System (Heating Oil) More Documents & Publications PIA - WEB Physical Security Major Application PIA - GovTrip (DOE data) PIA - WEB Unclassified...

420

Heat treatment furnace  

DOE Patents [OSTI]

A furnace heats through both infrared radiation and convective air utilizing an infrared/purge gas design that enables improved temperature control to enable more uniform treatment of workpieces. The furnace utilizes lamps, the electrical end connections of which are located in an enclosure outside the furnace chamber, with the lamps extending into the furnace chamber through openings in the wall of the chamber. The enclosure is purged with gas, which gas flows from the enclosure into the furnace chamber via the openings in the wall of the chamber so that the gas flows above and around the lamps and is heated to form a convective mechanism in heating parts.

Seals, Roland D; Parrott, Jeffrey G; DeMint, Paul D; Finney, Kevin R; Blue, Charles T

2014-10-21T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Molecular heat pump  

E-Print Network [OSTI]

We propose a novel molecular device that pumps heat against a thermal gradient. The system consists of a molecular element connecting two thermal reservoirs that are characterized by different spectral properties. The pumping action is achieved by applying an external force that periodically modulates molecular levels. This modulation affects periodic oscillations of the internal temperature of the molecule and the strength of its coupling to each reservoir resulting in a net heat flow in the desired direction. The heat flow is examined in the slow and fast modulation limits and for different modulation waveforms, thus making it possible to optimize the device performance.

Dvira Segal; Abraham Nitzan

2005-10-11T23:59:59.000Z

422

Heat storage with CREDA  

SciTech Connect (OSTI)

The principle of operation of ETS or Electric Thermal Storage is discussed in this book. As can be seen by the diagram presented, heating elements buried deep within the core are energized during off-peak periods or periods of lower cost energy. These elements charge the core to a per-determined level, then during the on-peak periods when the cost of electricity is higher or demand is higher, the heat is extracted from the core. The author discusses how this technology has progressed to the ETS equipment of today; this being the finer control of charging rates and extraction of heat from the core.

Beal, T. (Fostoria Industries, Fostoria, OH (US))

1987-01-01T23:59:59.000Z

423

Heat pumps and under floor heating as a heating system for Finnish low-rise residential buildings.  

E-Print Network [OSTI]

??In bachelor’s thesis the study of under floor heating system with ground source heat pump for the heat transfers fluid heating is considered. The case… (more)

Chuduk, Svetlana

2010-01-01T23:59:59.000Z

424

Domestic Heating and Thermal Insulation  

Science Journals Connector (OSTI)

... DIGEST 133 of the Building Research Station, entitled "Domestic Heating and Thermal Insulation" (Pp. 7. London : H.M. Stationery Office, 1960. 4insulation, the standard of heating, the ventilation-rate and the length of the heating season ...

1960-09-17T23:59:59.000Z

425

2659 heat insulation [n] (2)  

Science Journals Connector (OSTI)

constr....(Protection against heat provided by heat-shielding materials in the outer walls of a building to prevent heat build-up in hot regions or in temperate climates during the summer. In tempera...

2010-01-01T23:59:59.000Z

426

Heat Transfer and Convection Currents  

Science Journals Connector (OSTI)

...October 1965 research-article Heat Transfer and Convection Currents D. C...convection in a medium with internal heat generation is discussed semi-quantitatively...States English United Kingdom 1966 Heat transfer and convection currents Tozer D...

1965-01-01T23:59:59.000Z

427

Heat and Sound Insulation Materials  

Science Journals Connector (OSTI)

Of the three heat transfer processes: heat conduction, convection and radiation, convectional heat transfer is reduced by fiber and foam insulation materials1, 2). Air circulation is prevented by compartmentalizi...

Dr. Andre Knop; Dr. Louis A. Pilato

1985-01-01T23:59:59.000Z

428

Residential heating oil prices decline  

U.S. Energy Information Administration (EIA) Indexed Site

heating oil prices decline The average retail price for home heating oil is 3.48 per gallon. That's down 4.5 cents from a week ago, based on the residential heating fuel survey by...

429

Advances in induction heating  

SciTech Connect (OSTI)

Electric induction heating, in situ, can distill (underground) high-heat-value (HHV) gas, coal tar, bitumen, and shale oil. This technique permits potentially lower cost exploitation of the solid fossil fuels: coal, oil shale, tar sand, and heavy oil. The products, when brought to the surface in gaseous form and processed, yield chemical feedstocks, natural gas, and petroleum. Residual coke can be converted, in situ, to low-heat-value (LHV) gas by a conventional water-gas process. LHV can be burned at the surface to generate electricity at low cost. The major cost of the installation will have been paid for by the HHV gas and tar distilled from the coal. There are 2 mechanisms of heating by electric induction. One uses displacement currents induced from an electric field. The other uses eddy currents induced by a magnetic field.

Not Available

1980-06-16T23:59:59.000Z

430

Solar Heating Contractor Licensing  

Broader source: Energy.gov [DOE]

Michigan offers a solar heating contractor specialty license to individuals who have at least three years of experience installing solar equipment under the direction of a licensed solar contractor...

431

Heating and cooling system  

SciTech Connect (OSTI)

Heating and cooling of dwelling houses and other confined spaces is facilitated by a system in which thermal energy is transported between an air heating and cooling system in the dwelling and a water heat storage sink or source, preferably in the form of a swimming pool or swimming pool and spa combination. Special reversing valve circuitry and the use of solar collectors and liquid-to-liquid heat exchangers on the liquid side of the system , and special air valves and air modules on the air side of the system, enhance the system's efficiency and make it practical in the sense that systems employing the invention can utilize existing craft skills and building financing arrangements and building codes, and the like, without major modification.

Krumhansl, M.U.

1982-10-12T23:59:59.000Z

432

Solar heated swimming pool  

SciTech Connect (OSTI)

A swimming pool construction incorporating solar heating means to heat the pool water to a desired level. The pool includes a surrounding safety fence supported by a plurality of fence supports which are hollow and which include internal passageways. The pool water is passed through the pool support passageways whereupon it absorbs heat from the sidewalls of the fence supports, the surfaces of which have been heated by solar radiation. The fence supports can be made of plastic or other materials, but preferably are dark for improved absorptivity. The pool water can be passed serially through each of the fence supports and suitable thermostat control means can be provided to limit the water temperature increase.

Pettit, F.M.

1984-10-02T23:59:59.000Z

433

Electron Heat Transport Measured  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Heat Transport Measured in a Stochastic Magnetic Field T. M. Biewer, * C. B. Forest, J. K. Anderson, G. Fiksel, B. Hudson, S. C. Prager, J. S. Sarff, and J. C. Wright...

434

Wood Heating Fuel Exemption  

Broader source: Energy.gov [DOE]

This statute exempts from the state sales tax all wood or "refuse-derived" fuel used for heating purposes. The law does not make any distinctions about whether the qualified fuels are used for...

435

Absorption Heat Pump Developments  

Science Journals Connector (OSTI)

The implementation of both new thermodynamic cycles and new suitable fluids makes it possible to considerably widen the capacity to recover and upgrade low level heat contained particularly in industrial therm...

G. Cohen; A. Rojey

1983-01-01T23:59:59.000Z

436

Curling in the heat  

Science Journals Connector (OSTI)

... heat sensor, shown here, has been developed by Jim Gimzewski and colleagues at IBM Riis-chlikon specifically for studies of surface reactions . A spin-off of the scanning probe ...

David A. King

1994-04-21T23:59:59.000Z

437

Water Heating | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

to cut your water heating bill. Estimating Costs and Efficiency of Storage, Demand, and Heat Pump Water Heaters A water heater's energy efficiency is determined by the energy...

438

Heat flux limiting sleeves  

DOE Patents [OSTI]

A heat limiting tubular sleeve extending over only a portion of a tube having a generally uniform outside diameter, the sleeve being open on both ends, having one end thereof larger in diameter than the other end thereof and having a wall thickness which decreases in the same direction as the diameter of the sleeve decreases so that the heat transfer through the sleeve and tube is less adjacent the large diameter end of the sleeve than adjacent the other end thereof.

Harris, William G. (Tampa, FL)

1985-01-01T23:59:59.000Z

439

Heat Waves, Global Warming, and Mitigation  

E-Print Network [OSTI]

Heat Waves, Global Warming, and Mitigation Ann E. Carlson*II. HEAT WAVE DEFINITIONS .. A . HCHANGE AND HEAT WAVES .. CLIMATE III. IV. HEAT

Carlson, Ann E.

2008-01-01T23:59:59.000Z

440

Tokamak with liquid metal for inducing toroidal electrical field  

DOE Patents [OSTI]

A tokamak apparatus includes a vessel for defining a reservoir and confining liquid therein. A toroidal liner disposed within said vessel defines a toroidal space within the liner confines gas therein. Liquid metal fills the reservoir outside the liner. A magnetic field is established in the liquid metal to develop magnetic flux linking the toroidal space. The gas is ionized. The liquid metal and the toroidal space are moved relative to one another transversely of the space to generate electric current in the ionized gas in the toroidal space about its major axis and thereby heat plasma developed in the toroidal space.

Ohkawa, Tihiro (La Jolla, CA)

1981-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Convective heat flow probe  

DOE Patents [OSTI]

A convective heat flow probe device is provided which measures heat flow and fluid flow magnitude in the formation surrounding a borehole. The probe comprises an elongate housing adapted to be lowered down into the borehole; a plurality of heaters extending along the probe for heating the formation surrounding the borehole; a plurality of temperature sensors arranged around the periphery of the probe for measuring the temperature of the surrounding formation after heating thereof by the heater elements. The temperature sensors and heater elements are mounted in a plurality of separate heater pads which are supported by the housing and which are adapted to be radially expanded into firm engagement with the walls of the borehole. The heat supplied by the heater elements and the temperatures measured by the temperature sensors are monitored and used in providing the desired measurements. The outer peripheral surfaces of the heater pads are configured as segments of a cylinder and form a full cylinder when taken together. A plurality of temperature sensors are located on each pad so as to extend along the length and across the width thereof, with a heating element being located in each pad beneath the temperature sensors. An expansion mechanism driven by a clamping motor provides expansion and retraction of the heater pads and expandable packet-type seals are provided along the probe above and below the heater pads.

Dunn, J.C.; Hardee, H.C.; Striker, R.P.

1984-01-09T23:59:59.000Z

442

Intrinsically irreversible heat engine  

DOE Patents [OSTI]

A class of heat engines based on an intrinsically irreversible heat transfer process is disclosed. In a typical embodiment the engine comprises a compressible fluid that is cyclically compressed and expanded while at the same time being driven in reciprocal motion by a positive displacement drive means. A second thermodynamic medium is maintained in imperfect thermal contact with the fluid and bears a broken thermodynamic symmetry with respect to the fluid. The second thermodynamic medium is a structure adapted to have a low fluid flow impedance with respect to the compressible fluid, and which is further adapted to be in only moderate thermal contact with the fluid. In operation, thermal energy is pumped along the second medium due to a phase lag between the cyclical heating and cooling of the fluid and the resulting heat conduction between the fluid and the medium. In a preferred embodiment the engine comprises an acoustical drive and a housing containing a gas which is driven at a resonant frequency so as to be maintained in a standing wave. Operation of the engine at acoustic frequencies improves the power density and coefficient of performance. The second thermodynamic medium can be coupled to suitable heat exchangers to utilize the engine as a simple refrigeration device having no mechanical moving parts. Alternatively, the engine is reversible in function so as to be utilizable as a prime mover by coupling it to suitable sources and sinks of heat.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1984-01-01T23:59:59.000Z

443

Extraction process for removing metallic impurities from alkalide metals  

DOE Patents [OSTI]

A development is described for removing metallic impurities from alkali metals by employing an extraction process wherein the metallic impurities are extracted from a molten alkali metal into molten lithium metal due to the immiscibility of the alkali metals in lithium and the miscibility of the metallic contaminants or impurities in the lithium. The purified alkali metal may be readily separated from the contaminant-containing lithium metal by simple decanting due to the differences in densities and melting temperatures of the alkali metals as compared to lithium.

Royer, L.T.

1987-03-20T23:59:59.000Z

444

FEMP--Geothermal Heat Pumps  

Broader source: Energy.gov (indexed) [DOE]

heat pump-like an air conditioner or refrigera- heat pump-like an air conditioner or refrigera- tor-moves heat from one place to another. In the summer, a geothermal heat pump (GHP) operating in a cooling mode lowers indoor temperatures by transferring heat from inside a building to the ground outside or below it. Unlike an air condition- er, though, a heat pump's process can be reversed. In the winter, a GHP extracts heat from the ground and transfers it inside. Also, the GHP can use waste heat from summer air-conditioning to provide virtually free hot-water heating. The energy value of the heat moved is typically more than three times the electricity used in the transfer process. GHPs are efficient and require no backup heat because the earth stays at a relatively moderate temperature throughout the year.

445

Solar air heating system for combined DHW and space heating  

E-Print Network [OSTI]

Solar air heating system for combined DHW and space heating solar air collector PV-panel fannon-return valve DHW tank mantle cold waterhot water roof Solar Energy Centre Denmark Danish Technological Institute SEC-R-29 #12;Solar air heating system for combined DHW and space heating Søren �stergaard Jensen

446

PreHeat: Controlling Home Heating Using Occupancy Prediction  

E-Print Network [OSTI]

@comp.lancs.ac.uk ABSTRACT Home heating is a major factor in worldwide energy use. Our system, PreHeat, aims to more, and measuring actual gas consumption and occupancy. In UK homes PreHeat both saved gas and reduced MissTime (the Home heating uses more energy than any other residential energy expenditure including air conditioning

Krumm, John

447

Sumitomo Metal Industries Ltd Sumitomo Metals | Open Energy Information  

Open Energy Info (EERE)

Sumitomo Metal Industries Ltd Sumitomo Metals Sumitomo Metal Industries Ltd Sumitomo Metals Jump to: navigation, search Name Sumitomo Metal Industries Ltd (Sumitomo Metals) Place Osaka-shi, Osaka, Japan Zip 540-0041 Sector Solar Product Engaged in the steel, engineering, and electronics businesses; works on fuel cell component technology and manufactures silicon wafers for the solar sector. References Sumitomo Metal Industries Ltd (Sumitomo Metals)[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Sumitomo Metal Industries Ltd (Sumitomo Metals) is a company located in Osaka-shi, Osaka, Japan . References ↑ "Sumitomo Metal Industries Ltd (Sumitomo Metals)" Retrieved from "http://en.openei.org/w/index.php?title=Sumitomo_Metal_Industries_Ltd_Sumitomo_Metals&oldid=351744"

448

Liquid Salt Heat Exchanger Technology for VHTR Based Applications  

SciTech Connect (OSTI)

The objective of this research is to evaluate performance of liquid salt fluids for use as a heat carrier for transferring high-temperature process heat from the very high-temperature reactor (VHTR) to chemical process plants. Currently, helium is being considered as the heat transfer fluid; however, the tube size requirements and the power associated with pumping helium may not be economical. Recent work on liquid salts has shown tremendous potential to transport high-temperature heat efficiently at low pressures over long distances. This project has two broad objectives: To investigate the compatibility of Incoloy 617 and coated and uncoated SiC ceramic composite with MgCl2-KCl molten salt to determine component lifetimes and aid in the design of heat exchangers and piping; and, To conduct the necessary research on the development of metallic and ceramic heat exchangers, which are needed for both the helium-to-salt side and salt-to-process side, with the goal of making these heat exchangers technologically viable. The research will consist of three separate tasks. The first task deals with material compatibility issues with liquid salt and the development of techniques for on-line measurement of corrosion products, which can be used to measure material loss in heat exchangers. Researchers will examine static corrosion of candidate materials in specific high-temperature heat transfer salt systems and develop an in situ electrochemical probe to measure metallic species concentrations dissolved in the liquid salt. The second task deals with the design of both the intermediate and process side heat exchanger systems. Researchers will optimize heat exchanger design and study issues related to corrosion, fabrication, and thermal stresses using commercial and in-house codes. The third task focuses integral testing of flowing liquid salts in a heat transfer/materials loop to determine potential issues of using the salts and to capture realistic behavior of the salts in a small scale prototype system. This includes investigations of plugging issues, heat transfer, pressure drop, and the corrosion and erosion of materials in the flowing system.

Mark Anderson; Kumar Sridhara; Todd Allen; Per Peterson

2012-10-11T23:59:59.000Z

449

Effect of Channel Configurations for Tritium Transfer in Printed Circuit Heat Exchangers  

SciTech Connect (OSTI)

The Next Generation Nuclear Plant (NGNP), a very High temperature Gas-Cooled Reactor (VHTR) concept, will provide the first demonstration of a closed-loop Brayton cycle at a commercial scale of a few hundred megawatts electric and hydrogen production. The power conversion system (PCS) for the NGNP will take advantage of the significantly higher reactor outlet temperatures of the VHTR to provide higher efficiencies than can be achieved in the current generation of light water reactors. Besides demonstrating a system design that can be used directly for subsequent commercial deployment, the NGNP will demonstrate key technology elements that can be used in subsequent advanced power conversion systems for other Generation IV reactors. In anticipation of the design, development and procurement of an advanced power conversion system for the NGNP, the system integration of the NGNP and hydrogen plant was initiated to identify the important design and technology options that must be considered in evaluating the performance of the proposed NGNP. In the VHTR system, an intermediate heat exchanger (IHX), which transfers heat from the reactor core to the electricity or hydrogen production system is one key component, and its effectiveness is directly related to the system overall efficiency. In the VHTRs, the gas fluids used for coolant generally have poor heat transfer capability, so it requires very large surface area for a given condition. For this reason, a compact heat exchanger (CHE), which is widely used in industry especially for gasto-gas or gas-to-liquid heat exchange is considered as a potential candidate for an IHX replacing the classical shell and tube type heat exchanger. A compact heat exchanger is arbitrary referred to be a heat exchanger having a surface area density greater than 700 m2/m3. The compactness is usually achieved by fins and micro-channels, and leads to the enormous heat transfer enhancement and size reduction. The surface area density is the total heat transfer area divided by the volume of the heat exchanger. In the case of PCHE units, the heat transfer surface area density may be as high as 2,500 m2/m3. This high compactness implies an appreciable reduction in material reducing cost. In this study, heat transfer and tritium penetration analyses have been performed for two different channel configurations of the PCHE; (1) standard and (2) off-set. One of the goals of this study was to determine whether offsetting the hot and cold streams would significantly reduce the tritium flux, and whether or not it would affect the heat transfer significantly.

Chang Oh; Eung Kim; Robert Shrake; Mike Patterson

2009-05-01T23:59:59.000Z

450

Hydrogen and helium entrapment in flowing liquid metal plasma-facing surfaces  

E-Print Network [OSTI]

Hydrogen and helium entrapment in flowing liquid metal plasma-facing surfaces Ahmed Hassanein the PFC surface (helium and hydrogen isotopes) while accommodating high heat loads. To study this problem. Hydrogen isotope (DT) particles are likely be trapped in the liquid metal surface (e.g., lithium) due

Harilal, S. S.

451

Polymer quenched prealloyed metal powder  

DOE Patents [OSTI]

A powder metallurgical process of preparing a sheet from a powder having an intermetallic alloy composition such as an iron, nickel or titanium aluminide. The sheet can be manufactured into electrical resistance heating elements having improved room temperature ductility, electrical resistivity, cyclic fatigue resistance, high temperature oxidation resistance, low and high temperature strength, and/or resistance to high temperature sagging. The iron aluminide has an entirely ferritic microstructure which is free of austenite and can include, in weight %, 4 to 32% Al, and optional additions such as .ltoreq.1% Cr, .gtoreq.0.05% Zr .ltoreq.2% Ti, .ltoreq.2% Mo, .ltoreq.1% Ni, .ltoreq.0.75% C, .ltoreq.0.1% B, .ltoreq.1% submicron oxide particles and/or electrically insulating or electrically conductive covalent ceramic particles, .ltoreq.1% rare earth metal, and/or .ltoreq.3 % Cu. The process includes forming a non-densified metal sheet by consolidating a powder having an intermetallic alloy composition such as by roll compaction, tape casting or plasma spraying, forming a cold rolled sheet by cold rolling the non-densified metal sheet so as to increase the density and reduce the thickness thereof and annealing the cold rolled sheet. The powder can be a water, polymer or gas atomized powder which is subjecting to sieving and/or blending with a binder prior to the consolidation step. After the consolidation step, the sheet can be partially sintered. The cold rolling and/or annealing steps can be repeated to achieve the desired sheet thickness and properties. The annealing can be carried out in a vacuum furnace with a vacuum or inert atmosphere. During final annealing, the cold rolled sheet recrystallizes to an average grain size of about 10 to 30 .mu.m. Final stress relief annealing can be carried out in the B2 phase temperature range.

Hajaligol, Mohammad R. (Midlothian, VA); Fleischhauer, Grier (Midlothian, VA); German, Randall M. (State College, PA)

2001-01-01T23:59:59.000Z

452

Thermal heat radiation, near-field energy density and near-field radiative heat transfer of coated materials  

E-Print Network [OSTI]

We investigate the thermal radiation and thermal near-field energy density of a metal-coated semi-infinite body for different substrates. We show that the surface polariton coupling within the metal coating leads to an enhancement of the TM-mode part of the thermal near-field energy density when a polar substrate is used. In this case the result obtained for a free standing metal film is retrieved. In contrast, in the case of a metal substrate there is no enhancement in the TM-mode part, as can also be explained within the framework of surface plasmon coupling within the coating. Finally, we discuss the influence of the enhanced thermal energy density on the near-field radiative heat transfer between a simple semi-infinite and a coated semi-infinite body for different material combinations.

Svend-Age Biehs

2011-03-15T23:59:59.000Z

453

Heat and Metal Transfer in Gas Metal Arc Welding Using Argon and Helium  

E-Print Network [OSTI]

. Massachusetts Institute of Tc:chnology, is Head of Secondary Metallurgy Group with MEFOS. Lulea, Sweden. T

Eagar, Thomas W.

454

Evaluation of Protected Metal Hydride Slurries in a H2 Mini-  

E-Print Network [OSTI]

Evaluation of Protected Metal Hydride Slurries in a H2 Mini- Grid TIAX, LLC Acorn Park Cambridge_MERIT_REVIEW_MAY2003 2 Introduction Hydrogen Mini-Grid Concept Distributed FCPS utilizing a H2 Mini-Grid can provide waste heat can be used for hot water or space heating in buildings (i.e. "cogen") Distributed FCPS

455

Heat exchanger-accumulator  

DOE Patents [OSTI]

What is disclosed is a heat exchanger-accumulator for vaporizing a refrigerant or the like, characterized by an upright pressure vessel having a top, bottom and side walls; an inlet conduit eccentrically and sealingly penetrating through the top; a tubular overflow chamber disposed within the vessel and sealingly connected with the bottom so as to define an annular outer volumetric chamber for receiving refrigerant; a heat transfer coil disposed in the outer volumetric chamber for vaporizing the liquid refrigerant that accumulates there; the heat transfer coil defining a passageway for circulating an externally supplied heat exchange fluid; transferring heat efficiently from the fluid; and freely allowing vaporized refrigerant to escape upwardly from the liquid refrigerant; and a refrigerant discharge conduit penetrating sealingly through the top and traversing substantially the length of the pressurized vessel downwardly and upwardly such that its inlet is near the top of the pressurized vessel so as to provide a means for transporting refrigerant vapor from the vessel. The refrigerant discharge conduit has metering orifices, or passageways, penetrating laterally through its walls near the bottom, communicating respectively interiorly and exteriorly of the overflow chamber for controllably carrying small amounts of liquid refrigerant and oil to the effluent stream of refrigerant gas.

Ecker, Amir L. (Dallas, TX)

1980-01-01T23:59:59.000Z

456

In-situ ductile metal/bulk metallic glass matrix composites formed by chemical partitioning  

DOE Patents [OSTI]

A composite metal object comprises ductile crystalline metal particles in an amorphous metal matrix. An alloy is heated above its liquidus temperature. Upon cooling from the high temperature melt, the alloy chemically partitions, forming dendrites in the melt. Upon cooling the remaining liquid below the glass transition temperature it freezes to the amorphous state, producing a two-phase microstructure containing crystalline particles in an amorphous metal matrix. The ductile metal particles have a size in the range of from 0.1 to 15 micrometers and spacing in the range of from 0.1 to 20 micrometers. Preferably, the particle size is in the range of from 0.5 to 8 micrometers and spacing is in the range of from 1 to 10 micrometers. The volume proportion of particles is in the range of from 5 to 50% and preferably 15 to 35%. Differential cooling can produce oriented dendrites of ductile metal phase in an amorphous matrix. Examples are given in the Zr--Ti--Cu--Ni--Be alloy bulk glass forming system with added niobium.

Kim, Choong Paul (Northridge, CA); Hays, Charles C. (Pasadena, CA); Johnson, William L. (Pasadena, CA)

2007-07-17T23:59:59.000Z

457

Single metallic nanoparticle imaging for protein detection in cells  

Science Journals Connector (OSTI)

...to sensitive areas. The main...intensities. Single large metal particles...particle at its plasma resonance...a humidified atmosphere (95%) at...frequency of 1 MHz, we find {delta}{phi...for example, larger heating intensities...frequency of 1 MHz, we measured {delta...per focal spot area ?0.07 {mu...

L. Cognet; C. Tardin; D. Boyer; D. Choquet; P. Tamarat; B. Lounis

2003-01-01T23:59:59.000Z

458

THERMODYNAMIC STUDY OF HEAVY METALS BEHAVIOUR DURING MUNICIPAL WASTE INCINERATION  

E-Print Network [OSTI]

, heat and mass transfer, drying, pyrolysis, combustion of pyrolysis gases, combustion and gasificationTHERMODYNAMIC STUDY OF HEAVY METALS BEHAVIOUR DURING MUNICIPAL WASTE INCINERATION Y. ME´ NARD, A Me´tallurgie (LSG2M) Nancy, France T he incineration of municipal solid waste (MSW) contributes

Boyer, Edmond

459

Photoactivated metal removal  

SciTech Connect (OSTI)

The authors propose the use of photochromic dyes as light activated switches to bind and release metal ions. This process, which can be driven by solar energy, can be used in environmental and industrial processes to remove metals from organic and aqueous solutions. Because the metals can be released from the ligands when irradiated with visible light, regeneration of the ligands and concentration of the metals may be easier than with conventional ion exchange resins. Thus, the process has the potential to be less expensive than currently used metal extraction techniques. In this paper, the authors report on their studies of the metal binding of spirogyran dyes and the hydrolytic stability of these dyes. They have prepared a number of spirogyrans and measured their binding constants for calcium and magnesium. They discuss the relationship of the structure of the dyes to their binding strengths. These studies are necessary towards determining the viability of this technique.

Nimlos, M.R.; Filley, J.; Ibrahim, M.A.; Watt, A.S.; Blake, D.M.

1999-07-01T23:59:59.000Z

460

Welding of cast A359/SiC/10p metal matrix composites  

E-Print Network [OSTI]

arc welding GTAW Gas tungsten arc welding HAZ Heat affected zone HF High frequency MMC Metal matrix composite MMCs Metal matrix composites NDE Non-destructive examination SAW Submerged arc welding SMAW Shielded metal arc... limited their applications. Further, the use of composite materials requires us to stay from the established processes and areas of practice that were relevant to more conventional engineering materials. Except for gas tungsten arc welding (GTAW...

Kothari, Mitul Arvind

2005-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Definition: Heat | Open Energy Information  

Open Energy Info (EERE)

Heat Heat Jump to: navigation, search Dictionary.png Heat Heat is the form of energy that is transferred between systems or objects with different temperatures (flowing from the high-temperature system to the low-temperature system). Also referred to as heat energy or thermal energy. Heat is typically measured in Btu, calories or joules. Heat flow, or the rate at which heat is transferred between systems, has the same units as power: energy per unit time (J/s).[1][2][3][4] View on Wikipedia Wikipedia Definition In physics and chemistry, heat is energy in transfer between a system and its surroundings other than by work or transfer of matter. The transfer can occur in two simple ways, conduction, and radiation, and in a more complicated way called convective circulation. Heat is not a property

462

Metal atomization spray nozzle  

DOE Patents [OSTI]

A spray nozzle for a magnetohydrodynamic atomization apparatus has a feed passage for molten metal and a pair of spray electrodes mounted in the feed passage. The electrodes, diverging surfaces which define a nozzle throat and diverge at an acute angle from the throat. Current passes through molten metal when fed through the throat which creates the Lorentz force necessary to provide atomization of the molten metal. 6 figures.

Huxford, T.J.

1993-11-16T23:59:59.000Z

463

Heat and Power Systems Design  

E-Print Network [OSTI]

HEAT AND POWER SYSTEMS DESIGN H. D. Spriggs and J. V. Shah, Leesburg. VA ABSTRACT The selection of heat and power systems usually does not include a thorough analysis of the process heating. cooling and power requirements. In most cases..., these process requirements are accepted as specifications before heat and power systems are selected and designed. In t~is article we describe how Process Integration using Pinch Technology can be used to understand and achieve the minimum process heating...

Spriggs, H. D.; Shah, J. V.

464

Fabricated Metals (2010 MECS)  

Broader source: Energy.gov [DOE]

Manufacturing Energy and Carbon Footprint for Fabricated Metals Sector (NAICS 332) Energy use data source: 2010 EIA MECS (with adjustments) Footprint Last Revised: February 2014

465

EMSL - trace metals  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

trace-metals en Microbial Reductive Transformation of Phyllosilicate Fe(III) and U(VI) in Fluvial Subsurface Sediments. http:www.emsl.pnl.govemslwebpublications...

466

Acoustical heat pumping engine  

DOE Patents [OSTI]

The disclosure is directed to an acoustical heat pumping engine without moving seals. A tubular housing holds a compressible fluid capable of supporting an acoustical standing wave. An acoustical driver is disposed at one end of the housing and the other end is capped. A second thermodynamic medium is disposed in the housing near to but spaced from the capped end. Heat is pumped along the second thermodynamic medium toward the capped end as a consequence both of the pressure oscillation due to the driver and imperfect thermal contact between the fluid and the second thermodynamic medium. 2 figs.

Wheatley, J.C.; Swift, G.W.; Migliori, A.

1983-08-16T23:59:59.000Z

467

Optical heat flux gauge  

DOE Patents [OSTI]

A heat flux gauge comprising first and second thermographic phosphor layers separated by a layer of a thermal insulator. The gauge may be mounted on a surface with the first thermographic phosphor in contact with the surface. A light source is directed at the gauge, causing the phosphors to luminesce. The luminescence produced by the phosphors is collected and its spectra analyzed in order to determine the heat flux on the surface. First and second phosphor layers must be different materials to assure that the spectral lines collected will be distinguishable.

Noel, Bruce W. (Espanola, NM); Borella, Henry M. (Santa Barbara, CA); Cates, Michael R. (Oak Ridge, TN); Turley, W. Dale (Santa Barbara, CA); MaCarthur, Charles D. (Clayton, OH); Cala, Gregory C. (Dayton, OH)

1991-01-01T23:59:59.000Z

468

Optical heat flux gauge  

DOE Patents [OSTI]

A heat flux gauge comprising first and second thermographic phosphor layers separated by a layer of a thermal insulator wherein each thermographic layer comprises a plurality of respective thermographic phosphors. The gauge may be mounted on a surface with the first thermographic phosphor in contact with the surface. A light source is directed at the gauge, causing the phosphors to luminesce. The luminescence produced by the phosphors is collected and its spectra analyzed in order to determine the heat flux on the surface. First and second phosphor layers must be different materials to assure that the spectral lines collected will be distinguishable.

Noel, Bruce W. (Espanola, NM); Borella, Henry M. (Santa Barbara, CA); Cates, Michael R. (Oak Ridge, TN); Turley, W. Dale (Santa Barbara, CA); MacArthur, Charles D. (Clayton, OH); Cala, Gregory C. (Dayton, OH)

1991-01-01T23:59:59.000Z

469

Optical heat flux gauge  

DOE Patents [OSTI]

A heat flux gauge comprising first and second thermographic phosphor layers separated by a layer of a thermal insulator, wherein each thermographic layer comprises a plurality of respective thermographic sensors in a juxtaposed relationship with respect to each other. The gauge may be mounted on a surface with the first thermographic phosphor in contact with the surface. A light source is directed at the gauge, causing the phosphors to luminesce. The luminescence produced by the phosphors is collected and its spectra analyzed in order to determine the heat flux on the surface. First and second phosphor layers must be different materials to assure that the spectral lines collected will be distinguishable.

Noel, Bruce W. (Espanola, NM); Borella, Henry M. (Santa Barbara, CA); Cates, Michael R. (Oak Ridge, TN); Turley, W. Dale (Santa Barbara, CA); MacArthur, Charles D. (Clayton, OH); Cala, Gregory C. (Dayton, OH)

1991-01-01T23:59:59.000Z

470

Air heating system  

DOE Patents [OSTI]

A self-starting, fuel-fired, air heating system including a vapor generator, a turbine, and a condenser connected in a closed circuit such that the vapor output from the vapor generator is conducted to the turbine and then to the condenser where it is condensed for return to the vapor generator. The turbine drives an air blower which passes air over the condenser for cooling the condenser. Also, a condensate pump is driven by the turbine. The disclosure is particularly concerned with the provision of heat exchanger and circuitry for cooling the condensed fluid output from the pump prior to its return to the vapor generator.

Primeau, John J. (19800 Seminole Rd., Euclid, OH 44117)

1983-03-01T23:59:59.000Z

471

Heat Flow, Heat Transfer And Lithosphere Rheology In Geothermal Areas-  

Open Energy Info (EERE)

Flow, Heat Transfer And Lithosphere Rheology In Geothermal Areas- Flow, Heat Transfer And Lithosphere Rheology In Geothermal Areas- Features And Examples Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Heat Flow, Heat Transfer And Lithosphere Rheology In Geothermal Areas- Features And Examples Details Activities (5) Areas (5) Regions (0) Abstract: Surface heat flow measurements over active geothermal systems indicate strongly positive thermal anomalies. Whereas in "normal" geothermal settings, the surface heat flow is usually below 100-120 mW m- 2, in active geothermal areas heat flow values as high as several watts per meter squared can be found. Systematic interpretation of heat flow patterns sheds light on heat transfer mechanisms at depth on different lateral, depth and time scales. Borehole temperature profiles in active geothermal

472

Potassium, Uranium, Thorium Radiogenic Heat Contribution To Heat Flow In  

Open Energy Info (EERE)

Potassium, Uranium, Thorium Radiogenic Heat Contribution To Heat Flow In Potassium, Uranium, Thorium Radiogenic Heat Contribution To Heat Flow In The Precambrian And Younger Silicic Rocks Of The Zuni And Florida Mountains, New Mexico (Usa) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Potassium, Uranium, Thorium Radiogenic Heat Contribution To Heat Flow In The Precambrian And Younger Silicic Rocks Of The Zuni And Florida Mountains, New Mexico (Usa) Details Activities (4) Areas (2) Regions (0) Abstract: High heat flow in the Zuni Mountains, New Mexico, U.S.A., has been explained by the possible presence of a buried felsic pluton. Alternately, high K, U, Th abundances have been proposed to account for part of the high heat flow. The mean radiogenic heat contribution for 60 samples of Precambrian core rocks is 7.23 μcal/gm-yr, which is slightly

473

C-CAMP, A closed cycle alkali metal power system  

SciTech Connect (OSTI)

A concept is presented for a Closed-Cycle Alkali Metal (C-CAMP) power systems which utilizes the heat of reaction of an alkali metal and halogen compound to vaporize an alkali metal turbine fluid for a Rankine cycle. Unique features of the concept are (1) direct contact (heat exchange) between the reaction products and turbine fluid, and (2) a flow-through chemical reactor/boiler. The principal feasibility issues of the concept relate to the degree of cross-mixing of product and turbine fluid streams within the reactor-boiler. If proven feasible, the concept may be adapted to a range of fuel and turbine fluids and ultimately lead to thermal efficiencies in excess of 35%.

Wichner, R.P.; Hoffman, H.W.

1988-01-01T23:59:59.000Z

474

Porous metal hydride composite and preparation and uses thereof  

DOE Patents [OSTI]

A composite formed from large pieces of aggregate formed from (1) metal hydride (or hydride-former) powder and (2) either metal powder or plastic powder or both is prepared. The composite has large macroscopic interconnected pores (much larger than the sizes of the powders which are used) and will have a very fast heat transfer rate and low windage loss. It will be useful, for example, in heat engines, hydrogen storage devices, and refrigerator components which depend for their utility upon both a fast rate of hydriding and dehydriding. Additionally, a method of preparing the composite and a method of increasing the rates of hydriding and dehydriding of metal hydrides are also given.

Steyert, W.A.; Olsen, C.E.

1980-03-12T23:59:59.000Z

475

Porous metal hydride composite and preparation and uses thereof  

DOE Patents [OSTI]

A composite formed from large pieces of aggregate formed from (1) metal hydride (or hydride-former) powder and (2) either metal powder or plastic powder or both is prepared. The composite has large macroscopic interconnected pores (much larger than the sizes of the powders which are used) and will have a very fast heat transfer rate and low windage loss. It will be useful, for example, in heat engines, hydrogen storage devices, and refrigerator components which depend for their utility upon both a fast rate of hydriding and dehydriding. Additionally, a method of preparing the composite and a method of increasing the rates of hydriding and dehydriding of metal hydrides are also given.

Steyert, William A. (Los Alamos, NM); Olsen, Clayton E. (Los Alamos, NM)

1982-01-01T23:59:59.000Z

476

The GTE Ceramic Recuperator for High Temperature Waste Heat Recovery  

E-Print Network [OSTI]

Steel Bllffalo Metal Casting Standard St.eel N.ati_onal Forge Ladish Co. Pr.Jt.t & \\.fllitney Ama", Specl."11t.v Metals Bethlehem Steel Cape Ann Forge Staolev Spring (TRw) Box Forge Reheat, Steel Box Forge Reheat, Steel 1 Box Forge Reheat...,807 1.9 1.8 31 St.andard Steel Burnham, PA Box forge. Reheat, Steel 32 National Forge Erie, PA Ladle Preheater. Steel :,.} Lad isb Co. Cyntbiaca, ....'Y Box Heat Treat, Steell 188.426 77,527 3. Pra t t & \\.on i tney East Hart.ford, CT Box...

Dorazio, R. E.; Gonzalez, J. M.; Ferri, J. L.; Rebello, W. J.; Ally, M. R.

1984-01-01T23:59:59.000Z

477

Silicon metal-semiconductor-metal photodetector  

DOE Patents [OSTI]

Silicon MSM photodiodes sensitive to radiation in the visible to near infrared spectral range are produced by altering the absorption characteristics of crystalline Si by ion implantation. The implantation produces a defected region below the surface of the silicon with the highest concentration of defects at its base which acts to reduce the contribution of charge carriers formed below the defected layer. The charge carriers generated by the radiation in the upper regions of the defected layer are very quickly collected between biased Schottky barrier electrodes which form a metal-semiconductor-metal structure for the photodiode.

Brueck, Steven R. J. (Albuquerque, NM); Myers, David R. (Albuquerque, NM); Sharma, Ashwani K. (Albuquerque, NM)

1997-01-01T23:59:59.000Z

478

Silicon metal-semiconductor-metal photodetector  

DOE Patents [OSTI]

Silicon MSM photodiodes sensitive to radiation in the visible to near infrared spectral range are produced by altering the absorption characteristics of crystalline Si by ion implantation. The implantation produces a defected region below the surface of the silicon with the highest concentration of defects at its base which acts to reduce the contribution of charge carriers formed below the defected layer. The charge carriers generated by the radiation in the upper regions of the defected layer are very quickly collected between biased Schottky barrier electrodes which form a metal-semiconductor-metal structure for the photodiode.

Brueck, Steven R. J. (Albuquerque, NM); Myers, David R. (Albuquerque, NM); Sharma, Ashwani K. (Albuquerque, NM)

1995-01-01T23:59:59.000Z

479

Symmetry reduction of metal phthalocyanines on metals  

Science Journals Connector (OSTI)

The temperature-dependent adsorption behavior of fourfold symmetric metal phthalocyanines (MPcs) on metals with commensurate and incommensurate symmetries was investigated by scanning tunneling microscopy. On the fourfold symmetric Cu(100) surface, planar and fourfold molecular structures in two equivalent orientations were found for MPcs when prepared at room temperature. In addition, two metastable orientations were identified when prepared at low temperature, which can be depopulated upon annealing. MPcs adsorbed on the sixfold symmetric Cu(111) surface showed a disturbed molecular appearance. The symmetry of molecular structures changed from fourfold to twofold, which is discussed in terms of molecule-substrate interaction.

Shih-Hsin Chang; Stefan Kuck; Jens Brede; Leonid Lichtenstein; Germar Hoffmann; Roland Wiesendanger

2008-12-29T23:59:59.000Z

480

Heat driven heat pump using paired ammoniated salts  

SciTech Connect (OSTI)

A cycle for a heat driven heat pump using two salts CaCl/sup 2/.8NH/sup 3/, and ZnCl/sup 2/.4NH3 which may reversibly react with ammonia with the addition or evolution of heat. These salts were chosen so that both ammoniation processes occur at the same temperature so that the heat evolved may be used for comfort heating. The heat to drive the system need only be slightly hotter than 122 C. The low temperature source need only be slightly warmer than 0 C.

Dunlap, R.M.

1980-08-29T23:59:59.000Z

Note: This page contains sample records for the topic "finned metal heat" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

A Plastic-Core Compact Heat Exchanger for Energy Conservation  

E-Print Network [OSTI]

is 10 er cost compared to one with a metallic core, but it as the potential of contamination from mOisfre contained in air. All of these heat exchangers su fer from fouling by dust and particulates wile condensation of moisture leads to corrosion... maximum temperature does not exceed 340 K (150?F) while polypropylene is recommended for use up to 370 K (200?F). Fouling of the transfer surfaces has the negative effect of increasing the resistance to heat flow that leads to deterioration...

Lazaridis, A.; Rafailidis, E.

482

Experimental Research on Solar Assisted Heat Pump Heating System with Latent Heat Storage  

E-Print Network [OSTI]

-reaching meaning of solving energy and environment problems if new type energy conservation and environment protection heating system ? solar assisted ground-source heat pump (SAGHP) heating system with a latent heat storage tank will be practical... was established at the laboratory of construction energy conservation in Harbin Institute of Technology (HIT) in 2004. It added a latent heat storage tank in original SAGHP system. The schematic diagram of the system is shown in Figure 1. The experimental...

Han, Z.; Zheng, M.; Liu, W.; Wang, F.

2006-01-01T23:59:59.000Z

483

Planetary heat flow measurements  

Science Journals Connector (OSTI)

...ESA's Rosetta mission towards comet Churyumov-Gerasimenko. It...Heat flow measurements on comets have a different motivation...penetrator is by no means limited to comets; it has also been tested in...measurement. Currently, a landing on Mercury within the framework...

2005-01-01T23:59:59.000Z

484

Solar Heating and Cooling  

Science Journals Connector (OSTI)

...radiation during good weather are not very high, and...Atmospheric Administration weather ser-vice measures total...largely to experi-mental operation of 3-ton LiBr-H2O...a million solar water heaters are in use in these countries...air House heating load Cold air return 'S T~rgeo...

John A. Duffie; William A. Beckman

1976-01-16T23:59:59.000Z

485

Water-Heating Dehumidifier  

Energy Innovation Portal (Marketing Summaries) [EERE]

A small appliance developed at ORNL dehumidifies air and then recycles heat to warm water in a water heater. The device circulates cool, dry air in summer and warm air in winter. In addition, the invention can cut the energy required to run a conventional water heater by an estimated 50 per cent....

2010-12-08T23:59:59.000Z

486

INSULATION OF HEATING SYSTEMS  

Science Journals Connector (OSTI)

... C. PALLOT gave a Cantor Lecture to the Royal Society of Arts on “Thermal Insulation at Medium Temperature” on November 23 ; the lecture, which included many topics of ... many topics of current interest, has now been published1. In a bulletin on heat insulation issued by the Ministry of Fuel and Power, it was pointed out that "In ...

1943-05-22T23:59:59.000Z

487

Exotic heat PDE's  

E-Print Network [OSTI]

Exotic heat equations that allow to prove the Poincar\\'e conjecture, some related problems and suitable generalizations too are considered. The methodology used is the PDE's algebraic topology, introduced by A. Pr\\'astaro in the geometry of PDE's, in order to characterize global solutions.

Agostino Prástaro

2010-06-23T23:59:59.000Z

488

Roberts's “Heat and Thermodynamics”  

Science Journals Connector (OSTI)

... the last edition of the late Dr. J. K. Roberts's "Heat and Thermodynamics" appeared. The new material incorporated in this, the fourth edition, by Dr. ... ', but simply because new problems have afforded such excellent examples of the application of thermodynamics that their study must surely help the reader to a better understanding of the subject ...

G. R. NOAKES

1952-01-12T23:59:59.000Z

489

Wastewater heat recovery apparatus  

DOE Patents [OSTI]

A heat recovery system is described with a heat exchanger and a mixing valve. A drain trap includes a heat exchanger with an inner coiled tube, baffle plate, wastewater inlet, wastewater outlet, cold water inlet, and preheated water outlet. Wastewater enters the drain trap through the wastewater inlet, is slowed and spread by the baffle plate, and passes downward to the wastewater outlet. Cold water enters the inner tube through the cold water inlet and flows generally upward, taking on heat from the wastewater. This preheated water is fed to the mixing valve, which includes a flexible yoke to which are attached an adjustable steel rod, two stationary zinc rods, and a pivoting arm. The free end of the arm forms a pad which rests against a valve seat. The rods and pivoting arm expand or contract as the temperature of the incoming preheated water changes. The zinc rods expand more than the steel rod, flexing the yoke and rotating the pivoting arm. The pad moves towards the valve seat as the temperature of the preheated water rises, and away as the temperature falls, admitting a variable amount of hot water to maintain a nearly constant average process water temperature. 6 figs.

Kronberg, J.W.

1992-09-01T23:59:59.000Z

490

Wastewater heat recovery apparatus  

DOE Patents [OSTI]

A heat recovery system with a heat exchanger and a mixing valve. A drain trap includes a heat exchanger with an inner coiled tube, baffle plate, wastewater inlet, wastewater outlet, cold water inlet, and preheated water outlet. Wastewater enters the drain trap through the wastewater inlet, is slowed and spread by the baffle plate, and passes downward to the wastewater outlet. Cold water enters the inner tube through the cold water inlet and flows generally upward, taking on heat from the wastewater. This preheated water is fed to the mixing valve, which includes a flexible yoke to which are attached an adjustable steel rod, two stationary zinc rods, and a pivoting arm. The free end of the arm forms a pad which rests against a valve seat. The rods and pivoting arm expand or contract as the temperature of the incoming preheated water changes. The zinc rods expand more than the steel rod, flexing the yoke and rotating the pivoting arm. The pad moves towards the valve seat as the temperature of the preheated water rises, and away as the temperature falls, admitting a variable amount of hot water to maintain a nearly constant average process water temperature.

Kronberg, James W. (108 Independent Blvd., Aiken, SC 29801)

1992-01-01T23:59:59.000Z

491

institution Service Fin  

E-Print Network [OSTI]

with the up eed to have: eferred institut mary DUNS nu me, title, and em enter the infor ded verificatio st universit earching on th e n institution is r "List of Comp ent, or search for the institut thorized. Not Listed? ted, it may still uctions with th n or entity can HScompliant F o determine if i cies

Hutcheon, James M.

492

Water Heating | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Water Heating Water Heating Water Heating Infographic: Water Heaters 101 Everything you need to know about saving money on water heating costs Read more Selecting a New Water Heater Tankless? Storage? Solar? Save money on your water heating bill by choosing the right type of energy-efficient water heater for your needs. Read more Sizing a New Water Heater When buying a new water heater, bigger is not always better. Learn how to buy the right size of water heater. Read more You can reduce your monthly water heating bills by selecting the appropriate water heater for your home or pool and by using some energy-efficient water heating strategies. Some simple do-it-yourself projects, like insulating hot water pipes and lowering your water heating temperature, can also help you save money and energy on your water heating.

493

PHYTOEXTRACTION OF HEAVY METALS  

E-Print Network [OSTI]

) Type of phytoremediation Cost effective form of environmental remediation (Glass 1999) Chelating Agents: desorb heavy metals from soil matrix and form water-soluble metal complexes (Shen et al -using hyperaccumulator plant biomass to produce a bio-ore for commercial use -Li et al. look at using Ni

Blouin-Demers, Gabriel

494

Metallization of fluid hydrogen  

Science Journals Connector (OSTI)

...P. Tunstall Metallization of fluid hydrogen W. J. Nellis 1 A. A. Louis 2 N...The electrical resistivity of liquid hydrogen has been measured at the high dynamic...which structural changes are paramount. hydrogen|metallization of hydrogen|liquid...

1998-01-01T23:59:59.000Z

495

Electroreflectance in Metals  

Science Journals Connector (OSTI)

Calculations have been made which suggest that the prominent maximum in the electroreflectance spectra of metals observed by Feinleib is not due to modulation of the optical constants of the electrolyte, but to modulation of the optical constants of the metal.

Arnold Prostak and Wilford N. Hansen

1967-08-15T23:59:59.000Z

496

Integrated solar heating unit  

SciTech Connect (OSTI)

This patent describes an integral solar heating unit with an integral solar collector and hot water storage system, the unit comprising: (a) a housing; (b) a flat plate solar collector panel mounted in the housing and having a generally horizontal upper edge and an uninsulated, open back surface; (c) a cylindrical hot water tank operatively connected to the solar collector panel and mounted in the housing generally parallel to and adjacent to the upper edge; (d) the housing comprising a hood around the tank a pair of side skirts extending down at the sides of the panel. The hood and side skirts terminate at lower edges which together substantially define a plane such that upon placing the heating unit on a generally planar surface, the housing substantially encapsulates the collector panel and hot water tank in a substantially enclosed air space; (e) the collector including longitudinally extended U-shaped collector tubes and a glazed window to pass radiation through to the collector tubes, and a first cold water manifold connected to the tubes for delivering fresh water thereto and a second hot water manifold connected to the tubes to remove heated water therefrom. The manifolds are adjacent and at least somewhat above and in direct thermal contact with the tank; and, (f) the skirts and hood lapping around the collector panel, exposing only the glazed window, such that everything else in the heating unit is enclosed by the housing such that heat emanating from the uninsulated, open back face of the collector and tank is captured and retained by the housing to warm the manifolds.

Larkin, W.J.

1987-01-20T23:59:59.000Z

497

Review of Current Experience on Intermediate Heat Exchanger (IHX) and A Recommended Code Approach  

SciTech Connect (OSTI)

The purpose of the ASME/DOE Gen IV Task 7 Part I is to review the current experience on various high temperature reactor intermediate heat exchanger (IHX) concepts. There are several different IHX concepts that could be envisioned for HTR/VHTR applications in a range of temperature from 850C to 950C. The concepts that will be primarily discussed herein are: (1) Tubular Helical Coil Heat Exchanger (THCHE); (2) Plate-Stamped Heat Exchanger (PSHE); (3) Plate-Fin Heat Exchanger (PFHE); and (4) Plate-Machined Heat Exchanger (PMHE). The primary coolant of the NGNP is potentially subject to radioactive contamination by the core as well as contamination from the secondary loop fluid. To isolate the radioactivity to minimize radiation doses to personnel, and protect the primary circuit from contamination, intermediate heat exchangers (IHXs) have been proposed as a means for separating the primary circuit of the NGNP (Next Generation Nuclear Plant) or other process heat application from the remainder of the plant. This task will first review the different concepts of IHX that could be envisioned for HTR/VHTR applications in a range of temperature from 850 to 950 C. This will cover shell-and-tube and compact designs (including the platefin concept). The review will then discuss the maturity of the concepts in terms of design, fabricability and component testing (or feedback from experience when applicable). Particular attention will be paid to the feasibility of developing the IHX concepts for the NGNP with operation expected in 2018-2021. This report will also discuss material candidates for IHX applications and will discuss specific issues that will have to be addressed in the context of the HTR design (thermal aging, corrosion, creep, creep-fatigue, etc). Particular attention will be paid to specific issues associated with operation at the upper end of the creep regime.

Duane Spencer; Kevin McCoy

2010-02-02T23:59:59.000Z

498

Production of magnesium metal  

SciTech Connect (OSTI)

A process of producing magnesium metal includes providing magnesium carbonate, and reacting the magnesium carbonate to produce a magnesium-containing compound and carbon dioxide. The magnesium-containing compound is reacted to produce magnesium metal. The carbon dioxide is used as a reactant in a second process. In another embodiment of the process, a magnesium silicate is reacted with a caustic material to produce magnesium hydroxide. The magnesium hydroxide is reacted with a source of carbon dioxide to produce magnesium carbonate. The magnesium carbonate is reacted to produce a magnesium-containing compound and carbon dioxide. The magnesium-containing compound is reacted to produce magnesium metal. The invention further relates to a process for production of magnesium metal or a magnesium compound where an external source of carbon dioxide is not used in any of the reactions of the process. The invention also relates to the magnesium metal produced by the processes described herein.

Blencoe, James G. (Harriman, TN) [Harriman, TN; Anovitz, Lawrence M. (Knoxville, TN) [Knoxville, TN; Palmer, Donald A. (Oliver Springs, TN) [Oliver Springs, TN; Beard, James S. (Martinsville, VA) [Martinsville, VA

2010-02-23T23:59:59.000Z

499

Chromospheres of metal-deficient field giants  

SciTech Connect (OSTI)

Observations of the 2800-A Mg II line have been obtained with IUE for a sample of 10 metal-deficient field giant stars to search for chromospheric emission and signatures of mass loss, as well as to establish the level of chromospheric radiative energy losses from these stars. Mg II emission is probably present in all stars. High-resolution spectra of three of the brightest giants show asymmetric Mg II profiles which indicate a differentially expanding atmosphere, signaling the presence of outward mass motions. Surprisingly, the stellar surface fluxes in the Mg II lines are commensurate with the values found for disk giant stars (population I) of similar color. In spite of substantially depleted Mg abundances in the target stars (by factors of 10-100 relative to the solar abundance), the radiative losses implied by the Mg II fluxes, and possibly the chromospheric heating mechanism, appear to be reasonably independent of metallicity and age. 94 refs.

Dupree, A.K.; Hartmann, L.; Smith, G.H. (Harvard-Smithsonian Center for Astrophysics, Cambridge, MA (USA) Mount Stromlo and Siding Spring Observatories, Canberra (Australia))

1990-04-01T23:59:59.000Z

500

Pagosa Springs District Heating District Heating Low Temperature Geothermal  

Open Energy Info (EERE)

District Heating District Heating Low Temperature Geothermal District Heating District Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Pagosa Springs District Heating District Heating Low Temperature Geothermal Facility Facility Pagosa Springs District Heating Sector Geothermal energy Type District Heating Location Pagosa Springs, Colorado Coordinates 37.26945°, -107.0097617° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}