Powered by Deep Web Technologies
Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Effect of Diesel Oxidation Catalysts on the Diesel Particulate Filter Regeneration Process  

Science Journals Connector (OSTI)

Effect of Diesel Oxidation Catalysts on the Diesel Particulate Filter Regeneration Process ... A Diesel Particulate Filter (DPF) regeneration process was investigated during aftertreatment exhaust of a simulated diesel engine under the influence of a Diesel Oxidation Catalyst (DOC). ... Diesel particulate matter (PM) significantly contributes to urban air pollution and has often been associated with adverse health effects. ...

Leonardo Lizarraga; Stamatios Souentie; Antoinette Boreave; Christian George; Barbara D’Anna; Philippe Vernoux

2011-11-03T23:59:59.000Z

2

Diesel particulate filters  

Science Journals Connector (OSTI)

Is the broad market introduction of diesel particulate filters throughout Europe wishful thinking or reality? The challenges facing the introduction of diesel particulate filters with a fuel-borne catalyst...

Pierre Macaudičre; Laurent Rocher; Wolfgang Naschke

2004-04-01T23:59:59.000Z

3

Electrically-Assisted Diesel Particulate Filter Regeneration...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

More Documents & Publications Substrate Studies of an Electrically-Assisted Diesel Particulate Filter Electrically-Assisted Diesel Particulate Filter Regeneration...

4

Pleated Ceramic Fiber Diesel Particulate Filter | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Pleated Ceramic Fiber Diesel Particulate Filter Pleated Ceramic Fiber Diesel Particulate Filter 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters...

5

Filtering diesel exhaust gases with ceramic filters  

Science Journals Connector (OSTI)

Results are given from three test series on a ceramic filter for diesel exhausts. In the first and second series, use was made of diesel fuel (in the summer), while in...

A. Yu. Val’dberg; A. N. Tsedilin; T. O. Kosogorova…

2008-03-01T23:59:59.000Z

6

Diesel Soot Filter Characterization and Modeling for Advanced...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reactor regeneration of soot loaded catalyzed SCF * Micro-model of soot oxidation versus spatial catalyst loading. 7 2008 DOE OVT Merit Review Diesel Soot Filter Characterization...

7

Catalytic Filter for Diesel Exhaust Purification | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Filter for Diesel Exhaust Purification This project is developing a precious metal-free passive diesel particulate filter. deer09fokema.pdf More Documents & Publications...

8

Electrically-Assisted Diesel Particulate Filter Regeneration...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Evaluation pm041lance2011p.pdf More Documents & Publications Electrically-Assisted Diesel Particulate Filter Regeneration Substrate Studies of an Electrically-Assisted Diesel...

9

Predicting Thermal Stress in Diesel Particulate Filters | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Thermal Stress in Diesel Particulate Filters Predicting Thermal Stress in Diesel Particulate Filters 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: Corning...

10

Neutron Imaging of Diesel Particulate Filters | Department of...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Neutron Imaging of Diesel Particulate Filters Neutron Imaging of Diesel Particulate Filters Neutron computed tomography shows soot and ash loading in a cordierite diesel...

11

CLEERS Activities: Diesel Soot Filter Characterization & NOx...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Control Fundamentals CLEERS Activities: Diesel Soot Filter Characterization & NOx Control Fundamentals 2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit...

12

Modeling of Diesel Oxidation Catalyst  

Science Journals Connector (OSTI)

Modeling of Diesel Oxidation Catalyst ... Optimization of hydrocarbon (HC) oxidation over a diesel oxidation catalyst (DOC) requires consideration of (i) HC gas diffusion into the catalyst layer, (ii) HC gas adsorption and desorption from catalyst sites, and (iii) kinetics of the oxidation reaction. ... Mutagenicity of Diesel Engine Exhaust Is Eliminated in the Gas Phase by an Oxidation Catalyst but Only Slightly Reduced in the Particle Phase ...

Yasushi Tanaka; Takashi Hihara; Makoto Nagata; Naoto Azuma; Akifumi Ueno

2005-09-30T23:59:59.000Z

13

Development of SCR on Diesel Particulate Filter System for Heavy...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SCR on Diesel Particulate Filter System for Heavy Duty Applications Development of SCR on Diesel Particulate Filter System for Heavy Duty Applications Evaluation of a system...

14

Expanded Capacity Microwave-Cleaned Diesel Particulate Filter...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Expanded Capacity Microwave-Cleaned Diesel Particulate Filter Expanded Capacity Microwave-Cleaned Diesel Particulate Filter 2002 DEER Conference Presentation: Industrial Ceramic...

15

Ultra-Lite Diesel Particulate Filter Cartridge for Reduced Regeneratio...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Lite Diesel Particulate Filter Cartridge for Reduced Regeneration Time and Fuel Consumption Ultra-Lite Diesel Particulate Filter Cartridge for Reduced Regeneration Time and Fuel...

16

Durability of Diesel Engine Particulate Filters (Agreement ID...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Durability of Diesel Engine Particulate Filters (Agreement ID:10461) Durability of Diesel Engine Particulate Filters (Agreement ID:10461) 2013 DOE Hydrogen and Fuel Cells Program...

17

Improvement and Simplification of Diesel Particulate Filter System...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and Simplification of Diesel Particulate Filter System using a Ceria-Based Fuel-Borne Catalyst in Serial Applications Improvement and Simplification of Diesel Particulate Filter...

18

Diesel particulate filter with zoned resistive heater  

DOE Patents (OSTI)

A diesel particulate filter assembly comprises a diesel particulate filter (DPF) and a heater assembly. The DPF filters a particulate from exhaust produced by an engine. The heater assembly has a first metallic layer that is applied to the DPF, a resistive layer that is applied to the first metallic layer, and a second metallic layer that is applied to the resistive layer. The second metallic layer is etched to form a plurality of zones.

Gonze, Eugene V [Pinckney, MI

2011-03-08T23:59:59.000Z

19

Kinetics of Diesel Nanoparticle Oxidation  

Science Journals Connector (OSTI)

The oxidation rates in air of diesel nanoparticles sampled directly from the exhaust stream of a medium-duty diesel engine were measured over the temperature range of 800?1140 °C using online aerosol techniques. ... Particulate emission from diesel engines is currently a topic of great concern from both pollution and public health standpoints. ... In addition, the fundamental carbon-to-hydrogen ratio may be different in diesel particles as compared to the commonly used surrogates (15). ...

Kelly J. Higgins; Heejung Jung; David B. Kittelson; Jeffrey T. Roberts; Michael R. Zachariah

2003-03-25T23:59:59.000Z

20

Diesel Particle Filter and Fuel Effects on Heavy-Duty Diesel Engine Emissions  

Science Journals Connector (OSTI)

Diesel Particle Filter and Fuel Effects on Heavy-Duty Diesel Engine Emissions ... Gaseous and Particulate Emissions from Diesel Engines at Idle and under Load: Comparison of Biodiesel Blend and Ultralow Sulfur Diesel Fuels ...

Matthew A. Ratcliff; A. John Dane; Aaron Williams; John Ireland; Jon Luecke; Robert L. McCormick; Kent J. Voorhees

2010-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

A Standard Soot Generator for Diesel Particulate Filter Testing  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CAMBUSTION A Standard Soot Generator for Diesel Particulate Filter Testing Poster - P10 Diesel Engine Emission Reduction Conference 2007 Chris Nickolaus ...

22

Biodiesel Effects on Diesel Particle Filter Performance: Milestone Report  

SciTech Connect

Research results on the performance of biodiesel and biodiesel blends with ultra-low sulfur diesel (ULSD) and a diesel particle filter (DPF).

Williams, A.; McCormick, R. L.; Hayes, R.; Ireland, J.

2006-03-01T23:59:59.000Z

23

Neutron Imaging of Diesel Particulate Filters  

SciTech Connect

This article presents nondestructive neutron computed tomography (nCT) measurements of Diesel Particulate Filters (DPFs) as a method to measure ash and soot loading in the filters. Uncatalyzed and unwashcoated 200cpsi cordierite DPFs exposed to 100% biodiesel (B100) exhaust and conventional ultra low sulfur 2007 certification diesel (ULSD) exhaust at one speed-load point (1500rpm, 2.6bar BMEP) are compared to a brand new (never exposed) filter. Precise structural information about the substrate as well as an attempt to quantify soot and ash loading in the channel of the DPF illustrates the potential strength of the neutron imaging technique.

Strzelec, Andrea [ORNL; Bilheux, Hassina Z [ORNL; FINNEY, Charles E A [ORNL; Daw, C Stuart [ORNL; Foster, Prof. Dave [University of Wisconsin; Rutland, Prof. Christopher J. [University of Wisconsin; Schillinger, Burkhard [FRM-II, Technische Universitaet Munchen; Schulz, Michael [FRM-II, Technische Universitaet Munchen

2009-01-01T23:59:59.000Z

24

Effects of diesel particle filter retrofits and accelerated fleet turnover  

NLE Websites -- All DOE Office Websites (Extended Search)

Effects of diesel particle filter retrofits and accelerated fleet turnover Effects of diesel particle filter retrofits and accelerated fleet turnover on drayage truck emissions at the port of Oakland Title Effects of diesel particle filter retrofits and accelerated fleet turnover on drayage truck emissions at the port of Oakland Publication Type Journal Article Year of Publication 2011 Authors Dallmann, Timothy R., Robert A. Harley, and Thomas W. Kirchstetter Journal Environmental Science & Technology Volume 45 Issue 24 Pagination 10773-10779 Abstract Heavy-duty diesel drayage trucks have a disproportionate impact on the air quality of communities surrounding major freight-handling facilities. In an attempt to mitigate this impact, the state of California has mandated new emission control requirements for drayage trucks accessing ports and rail yards in the state beginning in 2010. This control rule prompted an accelerated diesel particle filter (DPF) retrofit and truck replacement program at the Port of Oakland. The impact of this program was evaluated by measuring emission factor distributions for diesel trucks operating at the Port of Oakland prior to and following the implementation of the emission control rule. Emission factors for black carbon (BC) and oxides of nitrogen (NOx) were quantified in terms of grams of pollutant emitted per kilogram of fuel burned using a carbon balance method. Concentrations of these species along with carbon dioxide were measured in the exhaust plumes of individual diesel trucks as they drove by en route to the Port. A comparison of emissions measured before and after the implementation of the truck retrofit/replacement rule shows a 54 ± 11% reduction in the fleet-average BC emission factor, accompanied by a shift to a more highly skewed emission factor distribution. Although only particulate matter mass reductions were required in the first year of the program, a significant reduction in the fleet-average NOx emission factor (41 ± 5%) was observed, most likely due to the replacement of older trucks with new ones.

25

Oil Bypass Filter and Diesel Engine Idling Wear-Rate Evaluations...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Bypass Filter and Diesel Engine Idling Wear-Rate Evaluations Oil Bypass Filter and Diesel Engine Idling Wear-Rate Evaluations 2005 Diesel Engine Emissions Reduction (DEER)...

26

Generator powered electrically heated diesel particulate filter  

DOE Patents (OSTI)

A control circuit for a vehicle powertrain includes a switch that selectivity interrupts current flow between a first terminal and a second terminal. A first power source provides power to the first terminal and a second power source provides power to the second terminal and to a heater of a heated diesel particulate filter (DPF). The switch is opened during a DPF regeneration cycle to prevent the first power source from being loaded by the heater while the heater is energized.

Gonze, Eugene V; Paratore, Jr., Michael J

2014-03-18T23:59:59.000Z

27

Diesel Particulate Filters and NO2 Emission Limits | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Filters and NO2 Emission Limits Diesel Particulate Filters and NO2 Emission Limits EPAs New air quality standards for NO2 will impact future DPF designs deer09ibrahim.pdf More...

28

Effects of Diesel Exhaust Emissions on Soot Oxidation and DPF...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Diesel Exhaust Emissions on Soot Oxidation and DPF Regeneration Effects of Diesel Exhaust Emissions on Soot Oxidation and DPF Regeneration DPF regeneration experiments verified the...

29

Reduction in (pro-)inflammatory responses of lung cells exposed in vitro to diesel exhaust treated with a non-catalyzed diesel particle filter  

Science Journals Connector (OSTI)

Abstract Increasingly stringent regulation of particulate matter emissions from diesel vehicles has led to the widespread use of diesel particle filters (DPFs), the effect of which on exhaust toxicity is so far poorly understood. We exposed a cellular model of the human respiratory epithelium at the air-liquid interface to non-catalyzed wall-flow DPF-filtered diesel exhaust and compared the resulting biological responses to the ones observed upon exposure to unfiltered exhaust. Filtered diesel exhaust acted highly oxidative, even though to a lesser extent than unfiltered exhaust (quantification of total reduced glutathione), and both exhaust types triggered comparable responses to oxidative stress (measurement of heme-oxygenase 1 (HMOX1) and superoxide-dismutase (SOD1) gene expression). Further, diesel exhaust filtration significantly reduced pro-inflammatory responses (measurement of tumor necrosis factor (TNF) and interleukin-8 (IL-8) gene expression and quantification of the secretion of their gene products TNF-? and IL-8). Because inflammatory processes are central to the onset of adverse respiratory health effects caused by diesel exhaust inhalation, our results imply that \\{DPFs\\} may make a valuable contribution to the detoxification of diesel vehicle emissions. The induction of significant oxidative stress by filtered diesel exhaust however, also implies that the non-particulate exhaust components also need to be considered for lung cell risk assessment.

Sandro Steiner; Jan Czerwinski; Pierre Comte; Loretta L. Müller; Norbert V. Heeb; Andreas Mayer; Alke Petri-Fink; Barbara Rothen-Rutishauser

2013-01-01T23:59:59.000Z

30

Modeling and interpreting the observed effects of ash on diesel particulate filter performance and regeneration  

E-Print Network (OSTI)

Diesel particulate filters (DPF) are devices that physically capture diesel particulates to prevent their release to the atmosphere. Diesel particulate filters have seen widespread use in on- and off-road applications as ...

Wang, Yujun, Ph. D. Massachusetts Institute of Technology

2014-01-01T23:59:59.000Z

31

Imaging of Diesel Particulate Filters using a High-Flux Neutron...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Imaging of Diesel Particulate Filters using a High-Flux Neutron Source Imaging of Diesel Particulate Filters using a High-Flux Neutron Source Detailed images of deposits identified...

32

Radio Frequency Diesel Particulate Filter Sensor Reduces Fuel Consumption, Wins R&D 100 Award  

Office of Energy Efficiency and Renewable Energy (EERE)

Radio Frequency Diesel Particulate Filter Sensor (RF-DPF) is a sensor that uses radio frequencies to measure the amount and distribution of soot and ash in the filters that remove particulate matter from the exhaust of diesel engines.

33

Development of a Sub-Grid Model of a Diesel Particulate Filter...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Sub-Grid Model of a Diesel Particulate Filter: application of the lattice-Boltzmann technique Development of a Sub-Grid Model of a Diesel Particulate Filter: application of the...

34

Testing an Active Diesel Particulate Filter on a 2-Cycle Marine...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Testing an Active Diesel Particulate Filter on a 2-Cycle Marine Engine Testing an Active Diesel Particulate Filter on a 2-Cycle Marine Engine Presentation given at DEER 2006,...

35

Impact of Biofuel Blending on Diesel Soot Oxidation: Implications for Aftertreatment  

SciTech Connect

Control strategies for diesel particulate filters (DPFs) remain one of the most important aspects of aftertreatment research and understanding the soot oxidation mechanism is key to controlling regeneration. Currently, most DPF models contain simple, first order heterogeneous reactions oxidation models with empirically fit parameters. This work improves the understanding of fundamental oxidation kinetics necessary to advance the capabilities of predictive modeling, by leading to better control over regeneration of the device. This study investigated the effects of blending soybean-derived biodiesel fuel on diesel particulate emissions under conventional combustion from a 1.7L direct injection, common rail diesel engine. Five biofuel blend levels were investigated and compared to conventional certification diesel for the nanostructure, surface chemistry and major constituents of the soluble organic fraction (SOF) of diesel particulate matter (PM), and the relationship between these properties and the particulate oxidation kinetics.

Strzelec, Andrea [ORNL; Toops, Todd J [ORNL; Lewis Sr, Samuel Arthur [ORNL; Daw, C Stuart [ORNL; Foster, David [University of Wisconsin; Rutland, Prof. Christopher J. [University of Wisconsin; Vander Wal, Dr. Randy [NASA-Glenn Research Center, Cleveland

2009-01-01T23:59:59.000Z

36

Single Wall Diesel Particulate Filter (DPF) Filtration Efficiency Studies Using Laboratory Generated Particles  

SciTech Connect

Diesel offers higher fuel efficiency, but produces higher exhaust particulate matter. Diesel particulate filters are presently the most efficient means to reduce these emissions. These filters typically trap particles in two basic modes: at the beginning of the exposure cycle the particles are captured in the filter holes, and at longer times the particles form a "cake" on which particles are trapped. Eventually the "cake" removed by oxidation and the cycle is repeated. We have investigated the properties and behavior of two commonly used filters: silicon carbide (SiC) and cordierite (DuraTrap® RC) by exposing them to nearly-spherical ammonium sulfate particles. We show that the transition from deep bed filtration to "cake" filtration can easily be identified by recording the change in pressure across the filters as a function of exposure. We investigated performance of these filters as a function of flow rate and particle size. The filters trap small and large particles more efficiently than particles that are ~80 to 200 nm in aerodynamic diameter. A comparison between the experimental data and a simulation using incompressible lattice-Boltzmann model shows very good qualitative agreement, but the model overpredicts the filter’s trapping efficiency.

Yang, Juan; Stewart, Marc; Maupin, Gary D.; Herling, Darrell R.; Zelenyuk, Alla

2009-04-15T23:59:59.000Z

37

Reduction of particulate matter and gaseous emission from marine diesel engines using a catalyzed particulate filter  

Science Journals Connector (OSTI)

Diesel engines are used widely as the power sources of coastal ships and international vessels primarily due to their high thermal efficiency, high fuel economy and durable performance. However, the gaseous and solid substances exhausted from diesel engines during the combustion process cause air pollution, in particular around harbor regions. In order to effectively reduce particulate matter and gaseous pollution emissions, a catalyzed particulate filter was equipped in the tail pipe of a marine diesel engine. The engine's performance and emission characteristics under various engine speeds and torques were measured using a computerized engine data control and acquisition system accompanied with an engine dynamometer. The effectiveness of installing a catalyzed particulate filter on the reduction of pollutant emissions was examined. The experimental results show that the exhaust gas temperature, carbon monoxide and smoke opacity were reduced significantly upon installation of the particulate filter. In particular, larger conversion of carbon monoxide to carbon dioxide — and thus larger CO2 and lower CO emissions — were observed for the marine diesel engine equipped with a catalyzed particulate filter and operated at higher engine speeds. This is presumably due to enhancement of the catalytic oxidation reaction that results from an exhaust gas with stronger stirring motion passing through the filter. The absorption of partial heating energy from the exhaust gas by the physical structure of the particulate filter resulted in a reduction in the exhaust gas temperature. The particulate matter could be burnt to a greater extent due to the effect of the catalyst coated on the surface of the particulate filter. Moreover, the fuel consumption rate was increased slightly while the excess oxygen emission was somewhat decreased with the particulate filter.

Cherng-Yuan Lin

2002-01-01T23:59:59.000Z

38

Zone heated diesel particulate filter electrical connection  

DOE Patents (OSTI)

An electrical connection system for a particulate filter is provided. The system includes: a particulate filter (PF) disposed within an outer shell wherein the PF is segmented into a plurality of heating zones; an outer mat disposed between the particulate filter and the outer shell; an electrical connector coupled to the outer shell of the PF; and a plurality of printed circuit connections that extend along the outer surface of the PF from the electrical connector to the plurality of heating zones.

Gonze, Eugene V. (Pinckney, MI); Paratore, Jr., Michael J. (Howell, MI)

2010-03-30T23:59:59.000Z

39

Direct Capillary Gas Chromatography of Filter-Borne Particulate Emissions from Diesel Engines  

Science Journals Connector (OSTI)

......Filter-Borne Particulate Emissions from Diesel Engines R.D. Cuthbertson P.R. Shore...Filter-Borne Particulate Emissions from Diesel Engines R.D. Cuthbertson and P.R...oil-derived material. Introduction Diesel engines emit particulate matter consisting......

R.D. Cuthbertson; P.R. Shore

1988-03-01T23:59:59.000Z

40

Reducing Emissions of a Diesel Engine Using Fumigation Ethanol and a Diesel Oxidation Catalyst  

Science Journals Connector (OSTI)

Reducing Emissions of a Diesel Engine Using Fumigation Ethanol and a Diesel Oxidation Catalyst ... † Department of Mechanical Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China ... In contrast to the conventional approach of using ethanol in spark-ignition engines, this study demonstrates the potential of ethanol utilization in diesel engines using dual-fuel combustion, where ethanol is injected into the intake manifold and diesel ... ...

K. S. Tsang; Z. H. Zhang; C. S. Cheung; T. L. Chan

2010-10-14T23:59:59.000Z

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

The effect of lubricant derived ash on the catalytic activity of diesel particulate filters  

E-Print Network (OSTI)

A diesel particulate filter (DPF) is an aftertreatment device used to remove hazardous particulate matter (PM) from diesel engine exhaust. Modem emission restrictions have limited the acceptable amount of PM output by ...

Murray, Timothy Quinn

2014-01-01T23:59:59.000Z

42

Combined Catalyzed Soot Filter and SCR Catalyst System for Diesel Engine Emission Reduction  

SciTech Connect

Substantially reduces particulate emission for diesel vehicles Up to 90% effective against carbonaceous particulate matter Significantly reduces CO and HC Filter regenerates at normal diesel operation temperatures Removable design for easy cleaning and maintenance.

Kakwani, R.M.

2000-08-20T23:59:59.000Z

43

Advanced Petroleum-Based Fuels - Diesel Emissions Project (APBF-DEC): 2,000-Hour Performance of a NOx Adsorber Catalyst and Diesel Particle Filter System for a Medium-Duty, Pick-Up Diesel Engine Platform; Final Report  

SciTech Connect

Presents the results of a 2,000-hour test of an emissions control system consisting of a nitrogen oxides adsorber catalyst in combination with a diesel particle filter, advanced fuels, and advanced engine controls in an SUV/pick-up truck vehicle platform.

Not Available

2007-03-01T23:59:59.000Z

44

Effectiveness of a Diesel Oxidation Catalyst (DOC) to control...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Effectiveness of a Diesel Oxidation Catalyst (DOC) to control CO and hydrocarbon emissions from Reactivity Controlled Compression Ignition (RCCI) combustion Effectiveness of a...

45

Diesel Particulate Oxidation Model: Combined Effects of Fixed...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Volatile Carbon Diesel Particulate Oxidation Model: Combined Effects of Fixed & Volatile Carbon Poster presented at the 16th Directions in Engine-Efficiency and Emissions Research...

46

Diesel emission control: Catalytic filters for particulate removal  

Science Journals Connector (OSTI)

The European diesel engine industry represents a vital sector across the Continent, with more than 2 million direct work positions and a turnover of over 400 billion Euro. Diesel engines provide large paybacks to society since they are extensively used to transport goods, services and people. In recent years increasing attention has been paid to the emissions from diesel engines which, like gasoline engine emissions, include carbon monoxide (CO), hydrocarbons (HC) and oxides of nitrogen (NOx). Diesel engines also produce significant levels of particulate matter (PM), which consists mostly of carbonaceous soot and a soluble organic fraction (SOF) of hydrocarbons that have condensed on the soot.Meeting the emission levels imposed for NOx and PM by legislation (Euro IV in 2005 and, in the 2008 perspective, Euro V) requires the development of a number of critical technologies to fulfill these very stringent emission limits (e.g. 0.005 g/km for PM). This review is focused on these innovative technologies with special reference to catalytic traps for diesel particulate removal.

Debora Fino

2007-01-01T23:59:59.000Z

47

Durability of Diesel Particulate Filters - Bench Studies on Cordierite...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

& Publications Requirements-Driven Diesel Catalyzed Particulate Trap Design and Optimization Development of Advanced Diesel Particulate Filtration (DPF) Systems fundamental...

48

Diesel Soot Oxidation with NO2:? Engine Experiments and Simulations  

Science Journals Connector (OSTI)

Diesel Soot Oxidation with NO2:? Engine Experiments and Simulations ... Particulate filtration in the exhaust system of diesel engines is increasingly gaining in importance for both light- and heavy-duty applications. ... The reaction rates are, in general, in the same order of magnitude with the engine-out soot emission rates. ...

Ioannis P. Kandylas; Onoufrios A. Haralampous; Grigorios C. Koltsakis

2002-09-20T23:59:59.000Z

49

Impact of Biodiesel Blending on Diesel Soot and the Regeneration of Particulate Filters  

Science Journals Connector (OSTI)

Diesel fuel production from renewable sources such as vegetable oils and animal fats offers the potential of both reducing fossil carbon emissions and producing alternative ultraclean transportation fuels. ... For temperature-programmed oxidation (TPO) tests, bulk samples were collected in quartz filters from diluted exhaust gas via a mini-dilution tunnel (Sierra Instruments BG-1). ... In addition to PM mass measurement, particulate samples were extracted directly from the exhaust stream using a thermophoretic sampling approach patterned after the work of Megaridis15 and Koylu,16 and described previously by Song et al.17 The thermophoretic samples were collected on 3-mm-diameter grids, constructed of 1-?m-thick copper and coated on one side with silicon oxide, using a pneumatically controlled probe to inject the sampling grid into the undiluted exhaust near the location where the other emissions samples were obtained in the exhaust pipe. ...

André L. Boehman; Juhun Song; Mahabubul Alam

2005-06-01T23:59:59.000Z

50

fundamental Modeling and Experimental Studies of Acicular Mullite Diesel Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE))

Pore-scale simulations of filtration and regeneration in acicular muillite diesel particulate filters have suggested underlying mechanisms that contribute to lower back pressures compared to other common DPF substrates.

51

MobiCleanTM Soot Filter for Diesel Locomotiive Applications ...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005deernewburry2.pdf More Documents & Publications California ARB Verification...

52

Comparative Analysis on the Effects of Diesel Particulate Filter and  

E-Print Network (OSTI)

samples representative of real-world emissions. Testing was conducted on a heavy-duty diesel engine and secondary emissions significantly. Introduction Advances in diesel engine and aftertreatment technologies) (1). Of these emissions, the most difficult to control in diesel engine applications are those of PM

Wu, Mingshen

53

Hydrogen Generation and Coke Formation over a Diesel Oxidation Catalyst under Fuel Rich Conditions  

Science Journals Connector (OSTI)

Hydrogen Generation and Coke Formation over a Diesel Oxidation Catalyst under Fuel Rich Conditions† ... Hydrogen production via hydrocarbon steam reforming and water gas shift reactions was investigated over a monolith-supported Pt-based diesel oxidation catalyst. ...

Meshari AL-Harbi; Jin-Yong Luo; Robert Hayes; Martin Votsmeier; William S. Epling

2010-12-08T23:59:59.000Z

54

CARB Verification of Catalyzed Diesel Particulate Filters for...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Sets 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005deerhuang.pdf More Documents & Publications Development and Applications of...

55

Predicting the Effect of Catalyst Axial Active Site Distributions on a Diesel Oxidation Catalyst Performance.  

E-Print Network (OSTI)

??Zone-coated diesel oxidation catalysts (DOCs) can be used to obtain overall improved performance in oxidation reaction extents. However, why this occurs and under what conditions… (more)

Al-Adwani, Suad

2012-01-01T23:59:59.000Z

56

Value Analysis of Alternative Diesel Particulate Filter (DPF...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

other materials at the same porosity. deer09majkowski.pdf More Documents & Publications SCR-DPF Integrations for Diesel ExhaustPerformance and Perspectives for High SCR Loadings...

57

A Standard Soot Generator for Diesel Particulate Filter Testing  

Energy.gov (U.S. Department of Energy (DOE))

Poster presentation at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

58

Oxidation of Proximal Protein Sulfhydryls by Phenanthraquinone, a Component of Diesel Exhaust Particles  

Science Journals Connector (OSTI)

Oxidation of Proximal Protein Sulfhydryls by Phenanthraquinone, a Component of Diesel Exhaust Particles ... Diesel exhaust particles (DEP) contain quinones that are capable of catalyzing the generation of reactive oxygen species in biological systems, resulting in induction of oxidative stress. ... 9,10-Phenanthrenequinone (9,10-PQ) is a PAHQ found in diesel exhaust particulates ... ...

Yoshito Kumagai; Sachie Koide; Keiko Taguchi; Akiko Endo; Yumi Nakai; Toshikazu Yoshikawa; Nobuhiro Shimojo

2002-02-28T23:59:59.000Z

59

US Tier 2 Bin 2 Diesel Research Progress  

Energy.gov (U.S. Department of Energy (DOE))

Describes how Tier 2 Bin 5 and US06 engine-out NOx levels were achieved and progress to meet Bin 2 through latest advances in lean NOx trap, diesel oxidation catalyst, and diesel particulate filter.

60

Catalytic diesel particulate filters reduce the in vitro estrogenic activity of diesel exhaust  

Science Journals Connector (OSTI)

An in vitro reporter gene assay based on human breast cancer T47D cells (ER-CALUX®...) was applied to examine the ability of diesel exhaust to induce or inhibit estrogen receptor (ER)-mediated gene expression. Exhaust

Daniela Wenger; Andreas C. Gerecke…

2008-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Retrofit and Testing of a Pre-Turbo, Diesel Oxidation Catalyst...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Retrofit and Testing of a Pre-Turbo, Diesel Oxidation Catalyst on a Tier 0, SD60M Freight Locomotive Achieving Over 50% PM Reduction Retrofit and Testing of a Pre-Turbo, Diesel...

62

Impact of Filtration Velocities and Particulate Matter Characteristics on Diesel Particulate Filter Wall Loading Performance  

SciTech Connect

The impact of different types of diesel particulate matter (PM) and different sampling conditions on the wall deposition and early soot cake build up within diesel particulate filters has been investigated. The measurements were made possible by a newly developed Diesel Exhaust Filtration Analysis (DEFA) system in which in-situ diesel exhaust filtration can be reproduced with in small cordierite wafer disks, which are essentially thin sections of a Diesel Particulate Filter (DPF) wall. The different types of PM were generated from selected engine operating conditions of a single-cylinder heavy-duty diesel engine. Two filtration velocities 4 and 8 cm/s were used to investigate PM deep-bed filtration processes. The loaded wafers were then analyzed in a thermal mass analyzer that measures the Soluble Organic Fraction (SOF) as well as soot and sulfate fractions of the PM. In addition, the soot residing in the wall of the wafer was examined under an optical microscope illuminated with Ultraviolet light and an Environmental Scanning Electron Microscope (E-SEM) to determine the bulk soot penetration depth for each loading condition. It was found that higher filtration velocity results in higher wall loading with approximately the same penetration depth into the wall. PM characteristics impacted both wall loading and soot cake layer characteristics. Results from imaging analysis indicate that soot the penetration depth into the wall was affected more by PM size (which changes with engine operating conditions) rather than filtration velocity.

Lance, Michael J [ORNL; Walker, Larry R [ORNL; Yapaulo, Renato A [ORNL; Orita, Tetsuo [ORNL; Wirojsakunchai, Ekathai [University of Wisconsin; Foster, David [University of Wisconsin; Akard, Michael [Horiba Instruments Inc.

2009-01-01T23:59:59.000Z

63

The effect of porosity on the mechanical properties of cordierite diesel particulate filter substrates  

SciTech Connect

Diesel particulate filter (DPF) technology depends on porous ceramic structures that trap the particulate matter in the diesel engine exhaust gas stream. The design of DPFs requires balancing the functional requirement of soot filtration with the mechanical properties and both are influenced by the porosity of the substrate. In addition, increasing the porosity of the substrate can assist with the catalytic washcoating, engine back pressure and engine efficiency. The effect of porosity on the elastic and fracture mechanical properties of cordierite based ceramic particulate filters was examined and will be described. Elastic modulus of DPF substrates was determined using resonant ultrasound spectroscopy while fracture toughness was characterized using the double-torsion test method. The interrelationships among specimen thickness, wall orientation, porosity and mechanical properties of the filter substrates will be discussed. A materials selection procedure to obtain filters with high thermal shock resistance and optimal mechanical properties will be described.

Shyam, Amit [ORNL; Lara-Curzio, Edgar [ORNL; Watkins, Thomas R [ORNL

2009-01-01T23:59:59.000Z

64

New Cordierite Diesel Particulate Filters for Catalyzed and Non...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

RESEARCH CONFERENCE (DEER 2006) PRESENTATIONS Combination and Integration of DPF-SCR Aftertreatment Technologies Advanced High Porosity Ceramic Honeycomb Wall Flow Filters...

65

MobiCleanTM Soot Filter for Diesel Locomotiive Applications  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

is trapped on the surface of a catalyzed, high temperature, wall flow, porous Silicon Carbide filter. Silicon Carbide provides superior thermal durability over metal fiber and...

66

Improvement and Simplification of Diesel Particulate Filter System...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FBC Improve the ash management (filter) Simplify the onboard dosing system and decrease cost and Chemist Ceramist Fuel system specialist Improve the vehicle integration for a Fit...

67

The Effect of an Axial Catalyst Distribution on the Performance of a Diesel Oxidation Catalyst and Inverse Hysteresis Phenomena during CO and C3H6 Oxidation.  

E-Print Network (OSTI)

??The Diesel Oxidation Catalyst (DOC) is a key component in the exhaust after-treatment system of diesel engines. In this study two aspects of a DOC… (more)

Abedi, Ali

2012-01-01T23:59:59.000Z

68

Dual-channel filter photometer system for biocomponent content determination in diesel oil  

Science Journals Connector (OSTI)

Currently, infrared spectrometry is the most often used method of determination of the biocomponent content in diesel oil, but this is also an expensive and time-consuming process. In this study, a portable, low-cost dual-channel filter photometer system is presented which meets the requirements of the European standard for biocomponent concentration measurements in diesel fuel. The results obtained using this novel system are reported and compared to the measurements made using a standard infrared spectrometer for biodiesel concentration between 0% and 20% by weight. The advantages of the new system, such as its adaptability to the different environmental conditions of analysis, are also discussed.

Jacek Go??biowski; Tomasz Prohu?

2008-01-01T23:59:59.000Z

69

Radio Frequency Diesel Particulate Filter Sensor Reduces Fuel...  

Office of Environmental Management (EM)

this process, known as regeneration, to only occur when needed, thereby reducing fuel consumption and enabling longer filter life. The RF-DPF can be used with light- and...

70

Lattice Boltzmann simulation on continuously regenerating diesel filter  

Science Journals Connector (OSTI)

...of the filter. We simulated a continuously regenerating DPF while simultaneously considering the deposition and combustion processes of soot particles. 2. Analytical model and X-ray computed tomography measurement In this section, the lattice...

2011-01-01T23:59:59.000Z

71

Zone heated inlet ignited diesel particulate filter regeneration  

SciTech Connect

An exhaust system that processes exhaust generated by an engine is provided. The system includes: a particulate filter (PF) that is disposed downstream of the engine and that filters particulates from the exhaust; and a grid that includes electrically resistive material that is segmented by non-conductive material into a plurality of zones and wherein the grid is applied to an exterior upstream surface of the PF.

Gonze, Eugene V [Pinckney, MI; Ament, Frank [Troy, MI

2012-06-26T23:59:59.000Z

72

Reduction of nitrogen oxides in diesel exhaust: Prospects for use of synthesis gas  

Science Journals Connector (OSTI)

Already commercialized and some of the most promising technologies of nitrogen oxide reduction in automotive diesel exhaust are compared. The Boreskov Institute of Catalysis... x ...

V. A. Kirillov; E. I. Smirnov; Yu. I. Amosov; A. S. Bobrin…

2009-01-01T23:59:59.000Z

73

Diesel Reforming for Solid Oxide Fuel Cell Application  

SciTech Connect

This presentation discusses the development of a diesel reforming catalyst and catalytic system development.

Liu, D-J.; Sheen, S-H.; Krumpelt, M.

2005-01-27T23:59:59.000Z

74

Experimental modeling of Wiener filters estimated on an operating diesel engine  

Science Journals Connector (OSTI)

Abstract Sound source separation in diesel engines can be implemented using a Wiener filter, or spectrofilter, that can extract the combustion contribution in the overall noise. In this study this filter characterizes the transfer function between a cylinder pressure and a measurement point. An engine is characterized by several filters (one for each cylinder) which are estimated for many operating conditions (engine speed and load). The purpose of this work is to obtain an averaged spectrofilter allowing the synthesis of combustion noise in all operating conditions. This synthesis should be accurate enough to be used in perceptive studies. In order to refine the spectrofilter estimation in the medium frequency band, this paper consists in taking advantage of the multitude of information given by the estimations from different operating conditions. To do this, an experimental model is adopted so modal parameters are extracted from a great number of measured filters. Different procedures such as the ESPRIT method or the LSCE method (modal analysis) are used to decompose the impulse responses on a complex exponential basis. The spectrofilters estimated from different operating conditions are analyzed and compared in this reduced basis, in order to identify the underlying structural parameters. These parameters are compared to the results of an experimental characterization of the stopped engine. The accuracy of the synthesis (number of components of the filter) is an important issue because these filters will be used in perceptive applications, extracting combustion noises. This paper is an extended version of the work initially presented at the conference Surveillance 6 in November 2011 in Compičgne, France [1] (J. Drouet, Quentin Leclere, Etienne Parizet. Experimental modeling of Wiener filters estimated on an operating diesel engine, in: Proceedings of the Surveillance, vol. 6, Compi‘egne, France, 2011.).

Julie Drouet; Quentin Leclčre; Etienne Parizet

2015-01-01T23:59:59.000Z

75

Engine-External HC-Dosing for Regeneration of Diesel Particulate Filters for Heavy Duty and NRMM According to Annex XXVII StVZO  

Energy.gov (U.S. Department of Energy (DOE))

This presentation discusses how a diesel particulate filter can be integrated in the exhaust piping of a heavy-duty engine.

76

Electrically resistive coating for remediation (regeneration) of a diesel particulate filter and method  

DOE Patents (OSTI)

A resistively heated diesel particulate filter (DPF). The resistively heated DPF includes a DPF having an inlet surface and at least one resistive coating on the inlet surface. The at least one resistive coating is configured to substantially maintain its resistance in an operating range of the DPF. The at least one resistive coating has a first terminal and a second terminal for applying electrical power to resistively heat up the at least one resistive coating in order to increase the temperature of the DPF to a regeneration temperature. The at least one resistive coating includes metal and semiconductor constituents.

Phelps, Amanda C. (Malibu, CA); Kirby, Kevin K. (Calabasas Hills, CA); Gregoire, Daniel J. (Thousand Oaks, CA)

2012-02-14T23:59:59.000Z

77

Organic Aerosol Formation from Photochemical Oxidation of Diesel Exhaust in a Smog Chamber  

Science Journals Connector (OSTI)

Diluted exhaust from a diesel engine was photo-oxidized in a smog chamber to investigate secondary organic aerosol (SOA) production. Photochemical aging rapidly produces significant SOA, almost doubling the organic aerosol contribution of primary ...

Emily A. Weitkamp; Amy M. Sage; Jeffrey R. Pierce; Neil M. Donahue; Allen L. Robinson

2007-09-11T23:59:59.000Z

78

Two-photon nitric oxide laser-induced fluorescence measurements in a diesel engine  

Science Journals Connector (OSTI)

A two-photon nitric oxide (NO) laser-induced fluorescence (LIF) technique was developed and applied to study in-cylinder diesel combustion. The technique prevents many problems...

Martin, Glen C; Mueller, Charles J; Lee, Chia-Fon F

2006-01-01T23:59:59.000Z

79

Retrofit and Testing of a Pre-Turbo, Diesel Oxidation Catalyst...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Retrofit and Testing of a Pre-Turbo, Diesel Oxidation Catalyst on a Tier 0, SD60M Freight Locomotive Achieving Over 50% PM Reduction Don Newburry Research & Development Manager...

80

Fuel Property, Emission Test, and Operability Results from a Fleet of Class 6 Vehicles Operating on Gas-to-Liquid Fuel and Catalyzed Diesel Particle Filters  

SciTech Connect

A fleet of six 2001 International Class 6 trucks operating in southern California was selected for an operability and emissions study using gas-to-liquid (GTL) fuel and catalyzed diesel particle filters (CDPF). Three vehicles were fueled with CARB specification diesel fuel and no emission control devices (current technology), and three vehicles were fueled with GTL fuel and retrofit with Johnson Matthey's CCRT diesel particulate filter. No engine modifications were made.

Alleman, T. L.; Eudy, L.; Miyasato, M.; Oshinuga, A.; Allison, S.; Corcoran, T.; Chatterjee, S.; Jacobs, T.; Cherrillo, R. A.; Clark, R.; Virrels, I.; Nine, R.; Wayne, S.; Lansing, R.

2005-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Effects of Diesel Oxidation Catalyst on Nanostructure and Reactivity of Diesel Soot  

Science Journals Connector (OSTI)

The combustible mixture in the cylinder of a diesel is always oxygen-rich in general, resulting in the existence of oxygen in the exhaust flow. ... range of the typical duty cycle for a diesel vehicle or to require a min. of active regeneration. ...

Zhihao Ma; Lei Li; Ying Chao; Ning Kang; Bin Xu; Jian Wu

2014-06-13T23:59:59.000Z

82

A MECHANISTIC MODEL FOR PARTICLE DEPOSITION IN DIESEL PARTICLUATE FILTERS USING THE LATTICE-BOLTZMANN TECHNIQUE  

SciTech Connect

Cordierite diesel particulate filters (DPFs) offer one of the most promising aftertreatment technologies to meet the quickly approaching EPA 2007 heavy-duty emissions regulations. A critical, yet poorly understood, component of particulate filter modeling is the representation of soot deposition. The structure and distribution of soot deposits upon and within the ceramic substrate directly influence many of the macroscopic phenomenon of interest, including filtration efficiency, back pressure, and filter regeneration. Intrinsic soot cake properties such as packing density and permeability coefficients remain inadequately characterized. The work reported in this paper involves subgrid modeling techniques which may prove useful in resolving these inadequacies. The technique involves the use of a lattice Boltzmann modeling approach. This approach resolves length scales which are orders of magnitude below those typical of a standard computational fluid dynamics (CFD) representation of an aftertreatment device. Individual soot particles are introduced and tracked as they move through the flow field and are deposited on the filter substrate or previously deposited particles. Electron micrographs of actual soot deposits were taken and compared to the model predictions. Descriptions of the modeling technique and the development of the computational domain are provided. Preliminary results are presented, along with some comparisons with experimental observations.

Stewart, Mark L.; Rector, David R.; Muntean, George G.; Maupin, Gary D.

2004-08-01T23:59:59.000Z

83

Loading and Regeneration Analysis of a Diesel Particulate Filter with a Radio Frequency-Based Sensor  

SciTech Connect

Accurate knowledge of diesel particulate filter (DPF) loading is critical for robust and efficient operation of the combined engine-exhaust aftertreatment system. Furthermore, upcoming on-board diagnostics regulations require on-board technologies to evaluate the status of the DPF. This work describes the application of radio frequency (RF) based sensing techniques to accurately measure DPF soot levels and the spatial distribution of the accumulated material. A 1.9L GM turbo diesel engine and a DPF with an RF-sensor were studied. Direct comparisons between the RF measurement and conventional pressure-based methods were made. Further analysis of the particulate matter loading rates was obtained with a mass-based soot emission measurement instrument (TEOM). Comparison with pressure drop measurements show the RF technique is unaffected by exhaust flow variations and exhibits a high degree of sensitivity to DPF soot loading and good dynamic response. Additional computational and experimental work further illustrates the spatial resolution of the RF measurements. Based on the experimental results, the RF technique shows significant promise for improving DPF control enabling optimization of the combined engine-aftertreatment system for improved fuel economy and extended DPF service life.

Sappok, Alex [Filter Sensing Technologies] [Filter Sensing Technologies; Prikhodko, Vitaly Y [ORNL] [ORNL; Parks, II, James E [ORNL

2010-01-01T23:59:59.000Z

84

Structure and Oxidation Activity Correlations for Carbon Blacks and Diesel Soot  

Science Journals Connector (OSTI)

This work focuses on a comprehensive investigation of structure–activity relationships for a diesel engine soot sample (Corning) and 10 commercially available carbon black samples. ... Su and colleagues used high-resolution transmission electron microscopy (HRTEM) and thermogravimetric analysis (TGA) to study the relation between the microstructure and oxidation behavior of soot from exhausts of different heavy-duty diesel engines and discovered the microstructure-controlled oxidation behavior of diesel soot. ... FE-SEM images (see Figure S1 of the Supporting Information) of some carbon blacks (Monarch 1400, Monarch 280, and Printex-U) and diesel soot-1 show the agglomerates, which are composed of their fundamental units called primary particles. ...

Lakshitha Pahalagedara; Hom Sharma; Chung-Hao Kuo; Saminda Dharmarathna; Ameya Joshi; Steven L. Suib; Ashish B. Mhadeshwar

2012-10-11T23:59:59.000Z

85

Mechanisms of Oxidation-Enhanced Wear in Diesel Exhaust Valves...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

May 18-22, 2009 -- Washington D.C. pmp01blau.pdf More Documents & Publications Friction and Wear Reduction in Diesel Engine Valve Trains Materials for Advanced Engine Valve Train...

86

Impact of Lube-oil Phosphorus on Diesel Oxidation Catalysts  

Energy.gov (U.S. Department of Energy (DOE))

Poster presentation at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

87

Characterization of particulate matter deposited in diesel particulate filters: Visual and analytical approach in macro-, micro- and nano-scales  

SciTech Connect

Multi-scale analytical investigations of particulate matter (soot and ash) of two loaded diesel particulate filters (DPF) from (a) a truck (DPF1) and (b) a passenger car (DPF2) reveal the following: in DPF1 (without fuel-borne additives), soot aggregates form an approximately 130-270 {mu}m thick, homogeneous porous cake with pronounced orientation. Soot aggregates consist of 15-30 nm large individual particles exhibiting relatively mature internal nanostructures, however, far from being graphite. Ash aggregates largely accumulate at the outlet part of DPF1, while minor amounts are deposited directly on the channel walls all along the filter length. They consist of crystalline phases with individual particles of sizes down to the nanoscale range. Chemically, the ash consists mainly of Mg, S, Ca, Zn and P, elements encountered in lubricating oil additives. In the passenger car DPF2 (with fuel-borne additives), soot aggregates form an approximately 200-500 {mu}m thick, inhomogeneous porous cake consisting of several superposed layers corresponding to different soot generations. The largest part of the soot cake is composed of unburned, oriented soot aggregates left behind despite repeated regenerations, while a small part constitutes a loose layer with randomly oriented aggregates, which was deposited last and has not seen any regeneration. Fe-oxide particles of micro- to nano-scale sizes, originating from the fuel-borne additive, are often dispersed within the part of the soot cake composed of the unburned soot leftovers. The individual soot nanoparticles in DPF2 are approximately 15-40 nm large and generally less mature than in the truck DPF1. The presence of soot leftovers in DPF2 indicates that the addition of fuel-borne material does not fully compensate for the temperatures needed for complete soot removal. Ash in DPF2 is filling up more than half of the filter volume (at the downstream part) and is dominated by Fe-oxide aggregates, due to the Fe-based fuel-borne additive, but otherwise its chemical composition reflects compounds of lubricating oil additives. (author)

Liati, Anthi; Dimopoulos Eggenschwiler, Panayotis [EMPA, Swiss Federal Laboratories for Materials Testing and Research, Laboratory for I.C. Engines, Duebendorf (Switzerland)

2010-09-15T23:59:59.000Z

88

REAL-WORLD EFFICACY OF HEAVY DUTY DIESEL TRUCK NOX AND PM EMISSIONS CONTROLS  

E-Print Network (OSTI)

are International. b DOC = Diesel Oxidation Catalyst; DPF = Diesel Particulate Filter; EGR = Exhaust GasREAL-WORLD EFFICACY OF HEAVY DUTY DIESEL TRUCK NOX AND PM EMISSIONS CONTROLS Gurdas Sandhu H 26-28, 2012 #12;2 Objectives 1. Quantify inter-run variability in exhaust emission rates 2. Assess

Frey, H. Christopher

89

Diesel Oxidation Catalyst Combined to Non-Thermal Plasma: Effect on Activation Catalyst Temperature and by-products formation  

E-Print Network (OSTI)

Diesel Oxidation Catalyst Combined to Non-Thermal Plasma: Effect on Activation Catalyst Temperature efficiency together with the catalyst activation temperature when a Diesel Oxidation Catalyst (DOC) is placed the advantageous plasma catalyst coupling effect on the lowering of the catalyst activation temperature

Paris-Sud XI, Université de

90

Effectiveness of Diesel Oxidation Catalyst in Reducing HC and CO Emissions from Reactivity Controlled Compression Ignition  

SciTech Connect

Reactivity Controlled Compression Ignition (RCCI) has been shown to allow for diesel-like or better brake thermal efficiency with significant reductions in nitrogen oxide (NOX) particulate matter (PM) emissions. Hydrocarbon (HC) and carbon monoxide (CO) emission levels, on the other hand, are similar to those of port fuel injected gasoline engines. The higher HC and CO emissions combined with the lower exhaust temperatures with RCCI operation present a challenge for current exhaust aftertreatments. The reduction of HC and CO emissions in a lean environment is typically achieved with an oxidation catalyst. In this work, several diesel oxidation catalysts (DOC) with different precious metal loadings were evaluated for effectiveness to control HC and CO emissions from RCCI combustion in a light-duty multi-cylinder engine operating on gasoline and diesel fuels. Each catalyst was evaluated in a steady-state engine operation with temperatures ranging from 160 to 260 C. A shift to a higher light-off temperature was observed during the RCCI operation. In addition to the steady-state experiments, the performances of the DOCs were evaluated during multi-mode engine operation by switching from diesel-like combustion at higher exhaust temperature and low HC/CO emissions to RCCI combustion at lower temperature and higher HC/CO emissions. High CO and HC emissions from RCCI generated an exotherm keeping the catalyst above the light-off temperature.

Prikhodko, Vitaly Y [ORNL; Curran, Scott [ORNL; Parks, II, James E [ORNL; Wagner, Robert M [ORNL

2013-01-01T23:59:59.000Z

91

Reformulated diesel fuel  

DOE Patents (OSTI)

Reformulated diesel fuels for automotive diesel engines which meet the requirements of ASTM 975-02 and provide significantly reduced emissions of nitrogen oxides (NO.sub.x) and particulate matter (PM) relative to commercially available diesel fuels.

McAdams, Hiramie T [Carrollton, IL; Crawford, Robert W [Tucson, AZ; Hadder, Gerald R [Oak Ridge, TN; McNutt, Barry D [Arlington, VA

2006-03-28T23:59:59.000Z

92

Mechanisms of Oxidation-Enhanced Wear in Diesel Exhaust Valves...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of wear oxidation microstructures of alloys Fe-, Ni-, Co-alloys h T h i h v Combined plastic deformation, wear, and oxidation on both valve and seat surfaces 6 Managed by...

93

Adsorption and Desorption of SOx on Diesel Oxidation Catalysts  

Science Journals Connector (OSTI)

In general the method proved to be very accurate and reproducible: the changes of SOx values caused by aging of the catalyst, change of the catalytic coating, or absorption and desorption processes were much higher than the errors of the analysis method. ... Besides its better material properties, the function of alumina as a sulfur trap might be appreciated as a measure to meet particulate matter (PM) emission limits in regulated engine test cycles. ... However, the temperature of diesel exhaust gas stays below 350 °C for almost the entire test cycle, that is, sulfur will be adsorbed under the testing conditions. ...

Oliver Kröcher; Markus Widmer; Martin Elsener; Dieter Rothe

2009-09-11T23:59:59.000Z

94

Impact of exhaust gas recirculation (EGR) on the oxidative reactivity of diesel engine soot  

SciTech Connect

This paper expands the consideration of the factors affecting the nanostructure and oxidative reactivity of diesel soot to include the impact of exhaust gas recirculation (EGR). Past work showed that soot derived from oxygenated fuels such as biodiesel carries some surface oxygen functionality and thereby possesses higher reactivity than soot from conventional diesel fuel. In this work, results show that EGR exerts a strong influence on the physical properties of the soot which leads to enhanced oxidation rate. HRTEM images showed a dramatic difference between the burning modes of the soot generated under 0 and 20% EGR. The soot produced under 0% EGR strictly followed an external burning mode with no evidence of internal burning. In contrast, soot generated under 20% EGR exhibited dual burning modes: slow external burning and rapid internal burning. The results demonstrate clearly that highly reactive soot can be achieved by manipulating the physical properties of the soot via EGR. (author)

Al-Qurashi, Khalid; Boehman, Andre L. [The EMS Energy Institute, The Pennsylvania State University, 405 Academic Activities Bldg., University Park, PA 16802 (United States)

2008-12-15T23:59:59.000Z

95

Activity and structure of perovskites as diesel reforming catalysts for solid oxide fuel cells.  

SciTech Connect

Recent progress in developing perovskite materials as more cost-effective catalysts in autothermal reforming (ATR) of diesel fuel to hydrogen-rich reformate for solid oxide fuel cell (SOFC) application is reported. Perovskite-type metal oxides with B sites partially exchanged by ruthenium were prepared and evaluated under ATR reaction conditions. The hydrogen yield, reforming efficiency, and CO{sub x} selectivity of these catalysts were investigated using diesel surrogate fuel with 50 ppm sulfur. The catalyst performances have approached or exceeded a benchmark, high-cost rhodium-based material. In parallel with the reactivity study, we also investigated the physical properties of B-site doped perovskites and their impact on the reforming performance using various characterization techniques such as BET, X-ray powder diffraction, temperature programmable reduction, scanning electron microscopy, and synchrotron X-ray absorption spectroscopy. We found that ruthenium is highly dispersed into perovskite lattice and its redox behavior is directly associated with reforming activity.

Liu, D.-J.; Krumpelt, M.; Chemical Engineering

2005-01-01T23:59:59.000Z

96

SCR/Urea filter — A new filtration application for diesel vehicles  

Science Journals Connector (OSTI)

In order that the systems which in future will be necessary for selective catalytic reduction (SCR) in diesel-engined vehicles are protected against wear and ... for all the known SCR systems on the market. Mann+...

Jochen Reyinger; Gunnar-Marcel Klein; Michael Durst

2007-07-01T23:59:59.000Z

97

Development of an Accelerated Ash-Loading Protocol for Diesel Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE))

Poster presentation at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

98

Effects of dilution conditions on diesel particle size distribution and filter mass measurements in case of marine fuels  

Science Journals Connector (OSTI)

Abstract Particle emission characteristics were studied from heavy-duty diesel engine operating on fuels with sulfur levels relevant to marine operation, i.e. 0.05% S and 3% S respectively. Effects of primary dilution temperature (PDT) and primary dilution ratio (PDR) were investigated together with effect of filter media and time of filter conditioning. PDT increase was found slowing down nucleation rate due to increase of saturation vapor pressures of volatile species. In turn, increasing PDR reduces partial pressure of exhaust species and hence weakens both homogeneous and heterogeneous nucleation. All these effects are amplified by high sulfur content in marine fuels which increases available amount of nucleation-prone vapor-phase semivolatile compounds. At the same time, water condensation artifact was observed at PDR = 3. No filter type was found to be overwhelmingly superior as certain positive and/or negative measurement artifacts are inherently associated with all filter materials. The filter conditioning time was also found to cause substantial PM mass variation, as control over VOC take up from (or lost to) laboratory air and hydration of sulfuric acid is required. The standard 24 hour conditioning time was found insufficient to reach complete PM mass equilibrium, so longer time is required when measuring from high-sulfur fuels.

Sergey Ushakov; Harald Valland; Jřrgen B. Nielsen; Erik Hennie

2014-01-01T23:59:59.000Z

99

Non-Catalytic Production of Hydrogen via Reforming of Diesel, Hexadecane and Bio-Diesel for Nitrogen Oxides Remediation.  

E-Print Network (OSTI)

?? After-treatment technologies are required for diesel engines to meet the current and future stringent emissions regulations. Lean NOx traps and SCR catalysts represent the… (more)

Hernandez-Gonzalez, Sergio Manuel

2008-01-01T23:59:59.000Z

100

A New CFD Model for understanding and Managing Diesel Particulate...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

& Publications Substrate Studies of an Electrically-Assisted Diesel Particulate Filter Diesel Particulate Filter: A Success for Faurecia Exhaust Systems Vehicle Evaluation of...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Local Soot Loading Distribution in Cordierite Diesel Particulate...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Local Soot Loading Distribution in Cordierite Diesel Particulate Filters by Dynamic Neutron Radiography Local Soot Loading Distribution in Cordierite Diesel Particulate Filters by...

102

Direct Capillary Gas Chromatography of Filter-Borne Particulate Emissions from Diesel Engines  

Science Journals Connector (OSTI)

......core (13). The hydrocarbons, which typically...products of the diesel combustion process (49...from incomplete combustion of fuel. Techniques...particulate- bound hydrocarbons have most often...analysis in individual heat-sealed plastic...Chromatograms and associated data were obtained via......

R.D. Cuthbertson; P.R. Shore

1988-03-01T23:59:59.000Z

103

Ultra-Lite Diesel Particulate Filter Cartridge for Reduced Regeneration Time and Fuel Consumption  

Energy.gov (U.S. Department of Energy (DOE))

Self-cleaning ceramic filter cartridges offer the advantage of better fuel economy, faster regeneration time, improved heat transfer, and reduction in manufacturing steps

104

Imaging of Diesel Particulate Filters using a High-Flux Neutron Source  

Energy.gov (U.S. Department of Energy (DOE))

Detailed images of deposits identified inside automotive DPFs using neutrons show how the deposits of soot, ash, and washcoat occurs within the filter.

105

Characterization of Particulate Matter Emissions from a Common-Rail Diesel Engine  

Science Journals Connector (OSTI)

Department of Materials Science and Chemical Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy ... The preferred approach to control the emissions of diesel engines is the adoption of an exhaust gas recirculation (EGR) system followed by a diesel oxidation catalyst (DOC) in front of a diesel particulate filter (DPF). ... Some fundamental information on the particulate matter (PM) characteristics emitted by an automotive diesel engine was gathered in order to provide a precious tool for the knowledge-based design of a new generation of diesel particulate traps in the EURO VI regulation perspective. ...

D. Fino; N. Russo

2011-02-02T23:59:59.000Z

107

Optimization of Engine-out Emissions from a Diesel Engine to Meet Tier 2 Bin 5 Emission Limits  

Energy.gov (U.S. Department of Energy (DOE))

Drastic reduction of engine-out emissions and complicated aftertreatment system comprising of oxidation catalyst, particulate filter, and DeNOx catalyst are implemented to meet Tier 2 Bin 5 limits for U.S. market diesel engines.

108

The Role of Phosphorus and Soot on the Deactivation of Diesel Oxidation Catalysts  

SciTech Connect

The deactivation of diesel oxidation catalysts (DOCs) by soot contamination and lube-oil derived phosphorus poisoning is investigated. Pt/CeO2/-Al2O3 DOCs aged using three different protocols developed by the authors and six high mileage field-returned DOCs of similar formulation are evaluated for THC and CO oxidation performance using a bench-flow reactor. Collectively, these catalysts exhibit a variety of phosphorus and soot morphologies contributing to performance deactivation. To isolate and examine the contribution of each deactivation mechanism, performance evaluations are carried out for each DOC ''as received'' and after removal of surface carbon in a high-temperature oxidizing environment. In such a manner the deactivation contribution of soot contamination is de-convoluted from that of phosphorus poisoning. It will be shown that this is accomplished while preserving phosphorus (and to a lesser degree sulfur, calcium and zinc) chemistries and concentrations within the washcoat. Washcoat contaminant information and materials changes are characterized using electron-probe microanalysis (EPMA), X-ray diffraction (XRD), scanning electron microscopy and energy dispersive spectroscopy (SEM-EDS), BET surface area, oxygen storage capacity (OSC), X-ray fluorescence (XRF) and inductively coupled plasma (ICP) analysis, from which the relative severity of each mechanism can be quantified. Results show that soot contamination from diesel exhaust severely degrades THC and CO oxidation performance by acting as a catalyst surface diffusion barrier. This results in a considerable increase of light-off temperatures. In contrast, phosphorus poisoning, which is considered a significant deactivation mechanism in three-way catalysts, is shown to have minimal effect on DOC oxidation performance for the conditions studied here. Material changes include the formation of both Ce(III-IV) and aluminum phosphates which do not significantly hinder the THC and CO oxidation in lean exhaust. In addition, thermal aging and sulfur poisoning are shown to produce minimal contributions to the overall deactivation. Consequently, performance of aged DOCs after soot removal is observed to be comparable to that of a fresh catalyst under our testing conditions.

Eaton, Scott J [ORNL; Nguyen, Ke [University of Tennessee, Knoxville (UTK); Bunting, Bruce G [ORNL; Toops, Todd J [ORNL

2009-01-01T23:59:59.000Z

109

Effects of Fuel Sulfur Content and Diesel Oxidation Catalyst on PM Emitted from Light-Duty Diesel Engine  

Science Journals Connector (OSTI)

This work aims at the particle number concentrations and size distributions, sulfate and trace metals emitted from a diesel engine fueled with three different sulfur content fuels, operating with and without DOC. ... Figure 2. Sulfate emission rate and fuel consumption as a function of sulfur content at engine speed of 2690 rpm. ... Thus, the use of low metal fuels and lubricating oil is as important to the environment and human health as low sulfur fuels, especially for engines with after-treatment devices. ...

Hong Zhao; Yunshan Ge; Xiaochen Wang; Jianwei Tan; Aijuan Wang; Kewei You

2010-01-05T23:59:59.000Z

110

Ultrafine PM Emissions from Natural Gas, Oxidation-Catalyst Diesel, and Particle-Trap Diesel Heavy-Duty Transit Buses  

Science Journals Connector (OSTI)

In urban areas, transit buses are a significant source of heavy-duty vehicle traffic, and many municipalities, including Los Angeles, Sacramento, Cleveland, and Atlanta, have recently modified their fleets to compressed natural gas (CNG) as the “clean” alternative to conventional uncontrolled diesel vehicles to meet increasingly strict particulate matter (PM) air quality regulations. ... ARB's mission is to promote and protect public health, welfare, and ecological resources through effective reduction of air pollutants while recognizing and considering effects on the economy. ...

Britt A. Holmén; Alberto Ayala

2002-11-05T23:59:59.000Z

111

Modeling Species Inhibition of NO oxidation in Urea-SCR Catalysts for Diesel Engine NOx Control  

SciTech Connect

Urea-selective catalytic reduction (SCR) catalysts are regarded as the leading NOx aftertreatment technology to meet the 2010 NOx emission standards for on-highway vehicles running on heavy-duty diesel engines. However, issues such as low NOx conversion at low temperature conditions still exist due to various factors, including incomplete urea thermolysis, inhibition of SCR reactions by hydrocarbons and H2O. We have observed a noticeable reduction in the standard SCR reaction efficiency at low temperature with increasing water content. We observed a similar effect when hydrocarbons are present in the stream. This effect is absent under fast SCR conditions where NO ~ NO2 in the feed gas. As a first step in understanding the effects of such inhibition on SCR reaction steps, kinetic models that predict the inhibition behavior of H2O and hydrocarbons on NO oxidation are presented in the paper. A one-dimensional SCR model was developed based on conservation of species equations and was coded as a C-language S-function and implemented in Matlab/Simulink environment. NO oxidation and NO2 dissociation kinetics were defined as a function of the respective adsorbate’s storage in the SCR catalyst. The corresponding kinetic models were then validated on temperature ramp tests that showed good match with the test data.

Devarakonda, Maruthi N.; Tonkyn, Russell G.; Tran, Diana N.; Lee, Jong H.; Herling, Darrell R.

2010-09-15T23:59:59.000Z

112

Modeling Species Inhibition of NO Oxidation in Urea-SCR Catalysts for Diesel Engine NOx Control  

SciTech Connect

Urea-selective catalytic reduction (SCR) catalysts are regarded as the leading NOx aftertreatment technology to meet the 2010 NOx emission standards for on-highway vehicles running on heavy-duty diesel engines. However, issues such as low NOx conversion at low temperature conditions still exist due to various factors, including incomplete urea thermolysis, inhibition of SCR reactions by hydrocarbons and H2O. We have observed a noticeable reduction in the standard SCR reaction efficiency at low temperature with increasing water content. We observed a similar effect when hydrocarbons are present in the stream. This effect is absent under fast SCR conditions where NO ~ NO2 in the feed gas. As a first step in understanding the effects of such inhibition on SCR reaction steps, kinetic models that predict the inhibition behavior of H2O and hydrocarbons on NO oxidation are presented in the paper. A one-dimensional SCR model was developed based on conservation of species equations and was coded as a C-language S-function and implemented in Matlab/Simulink environment. NO oxidation and NO2 dissociation kinetics were defined as a function of the respective adsorbate’s storage in the Fe-zeolite SCR catalyst. The corresponding kinetic models were then validated on temperature ramp tests that showed good match with the test data. Such inhibition models will improve the accuracy of model based control design for integrated DPF-SCR aftertreatment systems.

Devarakonda, Maruthi N.; Tonkyn, Russell G.; Tran, Diana N.; Lee, Jong H.; Herling, Darrell R.

2011-04-20T23:59:59.000Z

113

A case study of condition based maintenance modelling based upon the oil analysis data of marine diesel engines using stochastic filtering  

Science Journals Connector (OSTI)

This paper presents a case study of condition based maintenance modelling based on measured metal concentrations observed in oil samples of a fleet of marine diesel engines. The decision model for optimising the replacement time of the diesel engines conditional on observed measurements is derived and applied to the case discussed. We described the datasets, which were cleaned and re-organised according to the need of the research. The residual time distribution required in the decision model was formulated using a technique called stochastic filtering. Procedures for model parameter estimation are constructed and discussed in detail. The residual life model presented has been fitted to the case data, and the modelling outputs are discussed.

Wenbin Wang; B. Hussin; Tim Jefferis

2012-01-01T23:59:59.000Z

114

California ARB Verification Testing of the CBSTM Soot Filter...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

California ARB Verification Testing of the CBSTM Soot Filter for Stationary Diesel Applications California ARB Verification Testing of the CBSTM Soot Filter for Stationary Diesel...

115

Optimizing Low Temperature Diesel Combustion  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Diesel Particulate Filter Regenerations," SAE Paper 2007-01-3970, SAE Fall Powertrain and Fluids Systems Conference, Chicago, IL, Oct. 2007. * "Comprehensive Characterization of...

116

The California Demonstration Program for Control of PM from Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Backup Generators (BUGs) CARB Verification of Catalyzed Diesel Particulate Filters for Emergency Generator Sets Measuring "Real World" Heavy-Duty Diesel Emissions with a Mobile Lab...

117

Characteristics of SME Biodiesel-Fueled Diesel Particle Emissions and the Kinetics of Oxidation  

Science Journals Connector (OSTI)

In general it is reported that biodiesel has a less adverse effect on human health than petroleum-based diesel fuel. ... The engine used in this study was a 1996 John Deere T04045TF250, which is a medium-duty, off-highway, direct-injection, 4 cylinder, 4 cycle, turbocharged diesel engine. ... These fuels were compared with a low-sulfur, petroleum #2 diesel fuel in a Caterpillar 3304, prechamber, 75 kW diesel engine, operated over heavy- and light-duty transient test cycles developed by the United States Bureau of Mines. ...

Heejung Jung; David B. Kittelson; Michael R. Zachariah

2006-07-19T23:59:59.000Z

118

Global kinetics for a commercial diesel oxidation catalyst with two exhaust hydrocarbons  

Energy.gov (U.S. Department of Energy (DOE))

Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

119

Rational Catalyst Design Applied to Development of Advanced Oxidation Catalysts for Diesel Emission Control  

Energy.gov (U.S. Department of Energy (DOE))

Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

120

Best practices for underground diesel emissions  

SciTech Connect

The US NIOSH and the Coal Diesel Partnership recommend practices for successfully using ceramic filters to control particulate emitted from diesel-powered equipment used in underground coal mines. 3 tabs.

Patts, L.; Brnich, M. Jr. [NIOSH Pittsburgh Research Laboratory, Pittsburgh, PA (United States)

2007-08-15T23:59:59.000Z

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Reducing Diesel Engine Emissions  

NLE Websites -- All DOE Office Websites (Extended Search)

Reducing Reducing Diesel Engine Emissions 2 0 1 0 Green TransporTaTion TechnoloGies Compared to traditional gasoline engines, diesel engines require less maintenance, generate energy more efficiently, and produce less carbon dioxide emissions. But when uncontrolled, diesel engines churn out harmful emissions like particu- late matter (PM) and nitrogen oxides (NO x ). Researchers at Argonne National Laboratory are currently working to develop

122

The biological effects of subacute inhalation of diesel exhaust following addition of cerium oxide nanoparticles in atherosclerosis-prone mice  

SciTech Connect

Background: Cerium oxide (CeO{sub 2}) nanoparticles improve the burning efficiency of fuel, however, little is known about health impacts of altered emissions from the vehicles. Methods: Atherosclerosis-prone apolipoprotein E knockout (ApoE{sup -/-}) mice were exposed by inhalation to diluted exhaust (1.7 mg/m{sup 3}, 20, 60 or 180 min, 5 day/week, for 4 weeks), from an engine using standard diesel fuel (DE) or the same diesel fuel containing 9 ppm cerium oxide nanoparticles (DCeE). Changes in hematological indices, clinical chemistry, atherosclerotic burden, tissue levels of inflammatory cytokines and pathology of the major organs were assessed. Results: Addition of CeO{sub 2} to fuel resulted in a reduction of the number (30%) and surface area (10%) of the particles in the exhaust, whereas the gaseous co-pollutants were increased (6-8%). There was, however, a trend towards an increased size and complexity of the atherosclerotic plaques following DE exposure, which was not evident in the DCeE group. There were no clear signs of altered hematological or pathological changes induced by either treatment. However, levels of proinflammatory cytokines were modulated in a brain region and liver following DCeE exposure. Conclusions: These results imply that addition of CeO{sub 2} nanoparticles to fuel decreases the number of particles in exhaust and may reduce atherosclerotic burden associated with exposure to standard diesel fuel. From the extensive assessment of biological parameters performed, the only concerning effect of cerium addition was a slightly raised level of cytokines in a region of the central nervous system. Overall, the use of cerium as a fuel additive may be a potentially useful way to limit the health effects of vehicle exhaust. However, further testing is required to ensure that such an approach is not associated with a chronic inflammatory response which may eventually cause long-term health effects.

Cassee, Flemming R., E-mail: flemming.cassee@rivm.nl [National Institute for Public Health and the Environment, PO box 1, 3720 BA Bilthoven (Netherlands); Campbell, Arezoo, E-mail: acampbell@westernu.edu [Western University of Health Sciences, Pomona, CA (United States)] [Western University of Health Sciences, Pomona, CA (United States); Boere, A. John F., E-mail: john.boere@rivm.nl [National Institute for Public Health and the Environment, PO box 1, 3720 BA Bilthoven (Netherlands)] [National Institute for Public Health and the Environment, PO box 1, 3720 BA Bilthoven (Netherlands); McLean, Steven G., E-mail: smclean1@staffmail.ed.ac.uk [BHF/University Centre for Cardiovascular Sciences, University of Edinburgh, Edinburgh (United Kingdom); Duffin, Rodger, E-mail: Rodger.Duffin@ed.ac.uk [MRC Centre for Inflammation Research, University of Edinburgh, Edinburgh (United Kingdom)] [MRC Centre for Inflammation Research, University of Edinburgh, Edinburgh (United Kingdom); Krystek, Petra, E-mail: petra.krystek@philips.com [Philips Innovation Services, Eindhoven (Netherlands)] [Philips Innovation Services, Eindhoven (Netherlands); Gosens, Ilse, E-mail: Ilse.gosens@rivm.nl [National Institute for Public Health and the Environment, PO box 1, 3720 BA Bilthoven (Netherlands)] [National Institute for Public Health and the Environment, PO box 1, 3720 BA Bilthoven (Netherlands); Miller, Mark R., E-mail: Mark.Miller@ed.ac.uk [BHF/University Centre for Cardiovascular Sciences, University of Edinburgh, Edinburgh (United Kingdom)

2012-05-15T23:59:59.000Z

123

Light Duty Diesels in the United States - Some Perspectives ...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Particulate Filters: Market Introducution in Europe Diesel Particulate Filter: A Success for Faurecia Exhaust Systems Aftertreatment Modeling Status, Futur Potential, and...

124

Evaluation of oxides of nitrogen emissions for the purpose of their transient regulation from a direct injection diesel engine  

Science Journals Connector (OSTI)

The concept of defining a regulatory standard for the maximum allowable emissions of oxides of nitrogen (NOx) from a heavy-duty diesel engine on an instantaneous basis is presented. The significance of this concept from a regulatory point of view is the possibility to realise a steady brake specific NOx emissions result independent of the test schedule used. The emissions of oxides of nitrogen from a state-of-the-art direct injection diesel engine have been examined on an integral as well as on an instantaneous basis over the Federal Test Procedure as well as over several other arbitrary transient cycles generated for this study. Three candidate standards of specific NOx emissions have been evaluated on a real-time, continuous basis. These include brake power specific, fuel mass specific, and carbon dioxide mass specific NOx emissions. Retaining the stock engine control module, the carbon dioxide specific emissions of NOx have been shown to be the most uniform, varying only by about 30% of its mean value regardless of the test schedule or engine operation. The instantaneous fuel specific NOx emissions are shown to be relatively less invariant and the least steady are the brake power specific emissions with a coefficient of variation of up to 200%. Advancing injection timing has been shown to have a wide range of authority over the specific emissions of oxides of nitrogen regardless of the units used, when operating at full load in the vicinity of peak torque speeds. The carbon dioxide specific NOx emissions have shown a linear dependence on the power specific emissions, independent of the examined operating conditions. The trade-off between better brake thermal efficiency, lower exhaust gas temperature at advanced timing and lower NOx emissions has also been shown to be independent of the units of the specific standard used.

Yasser Yacoub; Chris Atkinson

2001-01-01T23:59:59.000Z

125

Review of Diesel Emission Control Technology  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Diesel Emission Control Technology Tim Johnson August 2002 2 Outline * Introduction - Regulatory update and technology approaches * Ultrafines * Filters * NOx - LNC - SCR - LNT *...

126

Influence of Oxidized Biodiesel Blends on Regulated and Unregulated Emissions from a Diesel Passenger Car  

Science Journals Connector (OSTI)

Few studies are available on modern passenger cars, employed common-rail engine systems, and after-treatment technologies, and even fewer studies report results, which are not necessarily representative of actual driving conditions, making it difficult to assess the fuel impact on diesel car fleet emissions. ... Although gasoline engines are expected to be replaced by hydrogen-powered fuel cells, compression-ignition engines, the diesel engines, are expected to remain in use for high-power applications because of limitations of hydrogen-storage densities. ... transesterification and sequential esterification-transesterification, followed by washing in water in both cases, in order to set out the most suitable operational conditions to achieve the highest FAME percentage in the shortest time. ...

Georgios Karavalakis; Evangelos Bakeas; Stamos Stournas

2010-05-24T23:59:59.000Z

127

Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Data Report No. 1  

SciTech Connect

The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NO{sub x}) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This interim data report summarizes results as of August, 1999, on the status of the test programs being conducted on three technologies: lean-NO{sub x} catalysts, diesel particulate filters and diesel oxidation catalysts.

DOE; ORNL; NREL; EMA; MECA

1999-08-15T23:59:59.000Z

128

Engine Tests of an Active PM Filter Regeneration System | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

System 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005deernickolas.pdf More Documents & Publications Diesel Particulate Filter: A...

129

Biodiesel versus diesel exposure: Enhanced pulmonary inflammation, oxidative stress, and differential morphological changes in the mouse lung  

SciTech Connect

The use of biodiesel (BD) or its blends with petroleum diesel (D) is considered to be a viable approach to reduce occupational and environmental exposures to particulate matter (PM). Due to its lower particulate mass emissions compared to D, use of BD is thought to alleviate adverse health effects. Considering BD fuel is mainly composed of unsaturated fatty acids, we hypothesize that BD exhaust particles could induce pronounced adverse outcomes, due to their ability to readily oxidize. The main objective of this study was to compare the effects of particles generated by engine fueled with neat BD and neat petroleum-based D. Biomarkers of tissue damage and inflammation were significantly elevated in lungs of mice exposed to BD particulates. Additionally, BD particulates caused a significant accumulation of oxidatively modified proteins and an increase in 4-hydroxynonenal. The up-regulation of inflammatory cytokines/chemokines/growth factors was higher in lungs upon BD particulate exposure. Histological evaluation of lung sections indicated presence of lymphocytic infiltrate and impaired clearance with prolonged retention of BD particulate in pigment laden macrophages. Taken together, these results clearly indicate that BD exhaust particles could exert more toxic effects compared to D. - Highlights: • Exposure of mice to BDPM caused higher pulmonary toxicity compared to DPM. • Oxidative stress and inflammation were higher in BD vs to D exposed mice. • Inflammatory lymphocyte infiltrates were seen only in lungs of mice exposed to BD. • Ineffective clearance, prolonged PM retention was present only after BD exposure.

Yanamala, Naveena, E-mail: wqu1@cdc.gov [Pathology and Physiology Research Branch/NIOSH/CDC, Morgantown, WV 26505 (United States); Hatfield, Meghan K., E-mail: wla4@cdc.gov [Pathology and Physiology Research Branch/NIOSH/CDC, Morgantown, WV 26505 (United States); Farcas, Mariana T., E-mail: woe7@cdc.gov [Pathology and Physiology Research Branch/NIOSH/CDC, Morgantown, WV 26505 (United States); Schwegler-Berry, Diane [Pathology and Physiology Research Branch/NIOSH/CDC, Morgantown, WV 26505 (United States); Hummer, Jon A., E-mail: qzh3@cdc.gov [Office of Mine Safety and Health Research/NIOSH/CDC, Pittsburgh, PA 15236 (United States); Shurin, Michael R., E-mail: shurinmr@upmc.edu [Department of Pathology, University of Pittsburgh Medical Center, Pittsburgh, PA (United States); Birch, M. Eileen, E-mail: mib2@cdc.gov [NIOSH/CDC, 4676 Columbia Parkway, Cincinnati, OH 45226 (United States); Gutkin, Dmitriy W., E-mail: dwgutkin@hotmail.com [Department of Pathology, University of Pittsburgh Medical Center, Pittsburgh, PA (United States); Kisin, Elena, E-mail: edk8@cdc.gov [Pathology and Physiology Research Branch/NIOSH/CDC, Morgantown, WV 26505 (United States); Kagan, Valerian E., E-mail: kagan@pitt.edu [Department of Environmental and Occupational Health, University of Pittsburgh, PA (United States); Bugarski, Aleksandar D., E-mail: zjl1@cdc.gov [Office of Mine Safety and Health Research/NIOSH/CDC, Pittsburgh, PA 15236 (United States); Shvedova, Anna A., E-mail: ats1@cdc.gov [Pathology and Physiology Research Branch/NIOSH/CDC, Morgantown, WV 26505 (United States); Department Physiology and Pharmacology, WVU, Morgantown, WV 26505 (United States)

2013-10-15T23:59:59.000Z

130

Effects of Diesel Exhaust Emissions on Soot Oxidation and DPF Regeneration  

Energy.gov (U.S. Department of Energy (DOE))

DPF regeneration experiments verified the effects of NO2 and O2 emissions found from the thermogravimetric analyzer soot oxidation.

131

Renewable Diesel  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Renewable Diesel Paraffinic (C 13 -C 18 ) No Oxygen No Double Bonds In Heart of Diesel Fuel (C 10 -C 22 ) High Cetane Feedstock Independent Cold Flow...

132

Diesel Soot Toxification  

Science Journals Connector (OSTI)

(2) The second significant trend is the more defective bulk and surface structure as the result of alteration of the fuel combustion process. ... Although the development of improved particle filters and novel methods for particulate removal in diesel cars is an ongoing task for industry the ultimate answer could be given by the future statistical analysis of mortality due to soot exposition. ...

Benjamin Frank; Robert Schlögl; Dang Sheng Su

2013-03-11T23:59:59.000Z

133

Diesel Engine Idling Test  

SciTech Connect

In support of the Department of Energy’s FreedomCAR and Vehicle Technology Program Office goal to minimize diesel engine idling and reduce the consumption of millions of gallons of diesel fuel consumed during heavy vehicle idling periods, the Idaho National Laboratory (INL) conducted tests to characterize diesel engine wear rates caused by extended periods of idling. INL idled two fleet buses equipped with Detroit Diesel Series 50 engines, each for 1,000 hours. Engine wear metals were characterized from weekly oil analysis samples and destructive filter analyses. Full-flow and the bypass filter cartridges were removed at four stages of the testing and sent to an oil analysis laboratory for destructive analysis to ascertain the metals captured in the filters and to establish wear rate trends. Weekly samples were sent to two independent oil analysis laboratories. Concurrent with the filter analysis, a comprehensive array of other laboratory tests ascertained the condition of the oil, wear particle types, and ferrous particles. Extensive ferrogram testing physically showed the concentration of iron particles and associated debris in the oil. The tests results did not show the dramatic results anticipated but did show wear trends. New West Technologies, LLC, a DOE support company, supplied technical support and data analysis throughout the idle test.

Larry Zirker; James Francfort; Jordon Fielding

2006-02-01T23:59:59.000Z

134

Spatial Temperature and Concentration Changes Following Heterogeneous Damage To a Model Diesel Oxidation Catalyst.  

E-Print Network (OSTI)

??Infra-Red thermography and spatially-resolved capillary inlet mass spectrometry (SpaciMS) have been used to characterize propylene oxidation along a Pt/Al2O3 monolith-supported catalyst, before and after heterogeneous… (more)

Russell, April Elizabeth

2010-01-01T23:59:59.000Z

135

SCR-DPF Integrations for Diesel ExhaustPerformance and Perspectives for High SCR Loadings  

Energy.gov (U.S. Department of Energy (DOE))

Presents laboratory and engine bench test results from integrating the SCR catalyst into the diesel filter as one multifunctional unit.

136

Emission Characteristics of a Diesel Engine Operating with In-Cylinder Gasoline and Diesel Fuel Blending  

SciTech Connect

Advanced combustion regimes such as homogeneous charge compression ignition (HCCI) and premixed charge compression ignition (PCCI) offer benefits of reduced nitrogen oxides (NOx) and particulate matter (PM) emissions. However, these combustion strategies often generate higher carbon monoxide (CO) and hydrocarbon (HC) emissions. In addition, aldehydes and ketone emissions can increase in these modes. In this study, the engine-out emissions of a compression-ignition engine operating in a fuel reactivity- controlled PCCI combustion mode using in-cylinder blending of gasoline and diesel fuel have been characterized. The work was performed on a 1.9-liter, 4-cylinder diesel engine outfitted with a port fuel injection system to deliver gasoline to the engine. The engine was operated at 2300 rpm and 4.2 bar brake mean effective pressure (BMEP) with the ratio of gasoline to diesel fuel that gave the highest engine efficiency and lowest emissions. Engine-out emissions for aldehydes, ketones and PM were compared with emissions from conventional diesel combustion. Sampling and analysis was carried out following micro-tunnel dilution of the exhaust. Particle geometric mean diameter, number-size distribution, and total number concentration were measured by a scanning mobility particle sizer (SMPS). For the particle mass measurements, samples were collected on Teflon-coated quartz-fiber filters and analyzed gravimetrically. Gaseous aldehydes and ketones were sampled using dinitrophenylhydrazine-coated solid phase extraction cartridges and the extracts were analyzed by liquid chromatography/mass spectrometry (LC/MS). In addition, emissions after a diesel oxidation catalyst (DOC) were also measured to investigate the destruction of CO, HC and formaldehydes by the catalyst.

Prikhodko, Vitaly Y [ORNL; Curran, Scott [ORNL; Barone, Teresa L [ORNL; Lewis Sr, Samuel Arthur [ORNL; Storey, John Morse [ORNL; Cho, Kukwon [ORNL; Wagner, Robert M [ORNL; Parks, II, James E [ORNL

2010-01-01T23:59:59.000Z

137

Evaluation of Passive and Active Soot Filters for Removal of...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Passive and Active Soot Filters for Removal of Particulate Emissions from Diesel Engines Evaluation of Passive and Active Soot Filters for Removal of Particulate Emissions from...

138

Comparison of Clean Diesel Buses to CNG Buses  

Office of Scientific and Technical Information (OSTI)

or to use the filters. However, for comparison purposes the cost to install diesel fuel tanks, dispensers, and related safetymonitoring equipment at a new 200-bus depot totals...

139

Design Challenges of Locomotive Diesel Engines | Department of...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Control Technology MobiCleanTM Soot Filter for Diesel Locomotiive Applications Integrated Engine and Aftertreatment Technology Roadmap for EPA 2010 Heavy-duty Emissions Regulations...

140

Natural Oils - The Next Generation of Diesel Engine Lubricants...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Aftertreatment with a Oil Conditioning Filter Effect of Exhaust Gas Recirculation (EGR) on Diesel Engine Oil - Impact on Wear Development of High Performance Heavy Duty Engine Oils...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Reliability and Design Strength Limit Calculations on Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Corning 2004deerwebb.pdf More Documents & Publications Predicting Thermal Stress in Diesel Particulate Filters Environmental Effects on Power Electronic Devices Effect of...

142

Failure Stress and Apparent Elastic Modulus of Diesel Particulate...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Elastic Modulus of Diesel Particulate Filter Ceramics Three established mechanical test specimen geometries and test methods for brittle materials are adapted to DPF...

143

Durability Evaluation of an Integrated Diesel NOx Adsorber A...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Diesel Engine Emissions Reduction (DEER) Conference Presentation: Cummins Inc. and Johnson-Matthey 2004deerli.pdf More Documents & Publications Desulfurization Fuel Filter...

144

Development of an Accelerated Ash-Loading Protocol for Diesel...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Accelerated Ash-Loading Protocol for Diesel Particulate Filters Bruce G. Bunting and Todd J. Toops Oak Ridge National Laboratory Adam Youngquist and Ke Nguyen University of...

145

Diesel Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Vehicles Vehicles Audi A3 Diesel vehicles may be making a comeback. Diesel engines are more powerful and fuel-efficient than similar-sized gasoline engines (about 30-35% more fuel efficient). Plus, today's diesel vehicles are much improved over diesels of the past. Better Performance Improved fuel injection and electronic engine control technologies have Increased power Improved acceleration Increased efficiency New engine designs, along with noise- and vibration-damping technologies, have made them quieter and smoother. Cold-weather starting has been improved also. Cleaner Mercedes ML320 BlueTEC Today's diesels must meet the same emissions standards as gasoline vehicles. Advances in engine technologies, ultra-low sulfur diesel fuel, and improved exhaust treatment have made this possible.

146

Mixed-Phase Oxide Catalyst Based on Mn-Mullite (Sm, Gd)Mn2O5 for NO Oxidation in Diesel Exhaust  

Science Journals Connector (OSTI)

...efficiency than gasoline engines (1). However...devices to reduce the engine-generated nitrogen...NOx to N 2 under fuel-rich regeneration...NOx-based pollutants, diesel engines also generate black...indicating the consumption of surface...

Weichao Wang; Geoffrey McCool; Neeti Kapur; Guang Yuan; Bin Shan; Matt Nguyen; Uschi M. Graham; Burtron H. Davis; Gary Jacobs; Kyeongjae Cho; Xianghong (Kelly) Hao

2012-08-17T23:59:59.000Z

147

Advanced Technology Light Duty Diesel Aftertreatment System  

Energy.gov (U.S. Department of Energy (DOE))

Light duty diesel aftertreatment system consisting of a DOC and selective catalytic reduction catalyst on filter (SCRF), close coupled to the engine with direct gaseous ammonia delivery is designed to reduce cold start NOx and HC emissions

148

Diesel Links  

NLE Websites -- All DOE Office Websites (Extended Search)

Links Links Exit Fueleconomy.gov The links below are to pages that are not part of the fueleconomy.gov Web site. We offer these external links for your convenience in accessing additional information that may be useful or interesting to you. Diesel Vehicles and Manufacturers Audi A3 (TDI models) A6 (TDI models) A7 (TDI models) A8 L (TDI model) Q5 (TDI models) Q7 (TDI models) BMW 328d Sedan 328d xDrive Sedan 328d xDrive Sports Wagon 535d Sedan 535d xDrive Sedan Chevrolet Cruze Turbo Diesel Jeep Grand Cherokee EcoDiesel Mercedes-Benz E250 BlueTEC GL350 BlueTEC GLK250 BlueTEC ML350 BlueTEC Porsche Cayenne Diesel Volkswagen Beetle (TDI models) Beetle Convertible (TDI models) Golf (TDI models) Jetta (TDI models) Jetta Sportwagen (TDI models) Passat (TDI models) Touareg (TDI models) Diesel-Related Information

149

Impact of the Fuel Molecular Structure on the Oxidation Process...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Oxidation Process of Real Diesel fuels According to Storage Conditions and Biodiesel Content Impact of the Fuel Molecular Structure on the Oxidation Process of Real Diesel fuels...

150

EPA Diesel Update  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

engines - Diesel vehicles have been available in Europe for many years - Diesel market penetration increased significantly coincidental with new diesel technologies * Industry...

151

Engines - Fuel Injection and Spray Research - Diesel Sprays  

NLE Websites -- All DOE Office Websites (Extended Search)

Diesel Sprays Diesel Sprays Chris Powell and fuel spray xray beamline Christopher Powell, an engine research scientist, fits a specially designed X-ray pressure window to a high-pressure chamber used in diesel spray research. These windows allow Argonne researchers to use X-rays to probe diesel sprays under the high-density conditions found in diesel engines. Diesel sprays Diesel engines are significantly more fuel-efficient than their gasoline counterparts, so wider adoption of diesels in the U.S. would decrease the nationÂ’s petroleum consumption. However, diesels emit much higher levels of pollutants, especially particulate matter and NOx (nitrogen oxides). These emissions have prevented more manufacturers from introducing diesel passenger cars. Researchers are exploring ways to reduce pollution formation in the engine

152

Mixed-Phase Oxide Catalyst Based on Mn-Mullite (Sm, Gd)Mn2O5 for NO Oxidation in Diesel Exhaust  

Science Journals Connector (OSTI)

...step of the reaction cycle, O 2 gas molecules decompose...available for the next cycle of NO conversion...ramp-up and ramp-down cycles. Four key factors contribute...performs in simulated diesel exhaust, we added MnCe-7...R. J. Farrauto, Fundamentals of Industrial Catalytic...

Weichao Wang; Geoffrey McCool; Neeti Kapur; Guang Yuan; Bin Shan; Matt Nguyen; Uschi M. Graham; Burtron H. Davis; Gary Jacobs; Kyeongjae Cho; Xianghong (Kelly) Hao

2012-08-17T23:59:59.000Z

153

Enlaces Diesel  

NLE Websites -- All DOE Office Websites (Extended Search)

Enlaces Diesel Enlaces Diesel Los siguientes enlaces no son parte del sitio ahorremosgasolina.gov. Le ofrecemos estos enlaces externos para que a su conveniencia tenga acceso a informaciĂłn adicional que puede serle Ăştil o interesante para usted. VehĂ­culos y Fabricantes Diesel Audi A3 (modelos TDI) Q7 (modelos TDI) Mercedes-Benz Mercedes E350 BlueTEC Mercedes GL350 BlueTEC Mercedes ML350 BlueTEC Mercedes R350 BlueTEC Volkswagen Golf (modelos TDI) Jetta (modelos TDI) Jetta Sportwagen (modelos TDI) Touareg (modelos TDI) InformaciĂłn Sobre el Diesel Biodiesel Abundante informaciĂłn sobre el biodiesel proporcionada por el Centro de Datos de Combustibles Alternativos y VehĂ­culos Avanzados (AFDC) Mezclas de Biodiesel ĂŤcono de Adobe Acrobat Informe sobre el debate de las mezclas de biodiesel desarrollado por el programa de Ciudades Limpias del EERE.

154

Materials - Catalysts for Diesel Engines  

NLE Websites -- All DOE Office Websites (Extended Search)

Argonne's deNOx Catalyst Begins Extensive Diesel Engine Exhaust Testing Argonne's deNOx Catalyst Begins Extensive Diesel Engine Exhaust Testing denox monolith Argonne's deNOx catalyst can be prepared as a powder or a monolith. chris marshall Principal investigator Chris Marshall shows the monolith form of the Argonne deNOx catalyst with a sensor inserted for testing. doug longman Mechanical engineer Doug Longman inserts the instrumented deNOx catalyst monolith into the aftertreatment chamber of Argonne's heavy-duty Caterpillar diesel test engine. Background Diesel engines, while efficient, produce many undesirable combustion byproducts in their exhaust. While we tend to think of the sooty exhaust products we see as the bad stuff, it is the less-visible exhaust products such as nitrogen oxides (NOx) that create bigger problems.

155

Friction and Wear Reduction in Diesel Engine Valve Trains | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

More Documents & Publications Mechanisms of Oxidation-Enhanced Wear in Diesel Exhaust Valves Materials for Advanced Engine Valve Train Materials for Advanced Engine Valve Train...

156

Diesel Reforming for Fuel Cell Auxiliary Power Units  

SciTech Connect

This objective of this project was to develop technology suitable for onboard reforming of diesel. The approach was to examine catalytic partial oxidation and steam reforming.

Borup, R.; Parkinson, W. J.; Inbody, M.; Brosha, E.L.; Guidry, D.R.

2005-01-27T23:59:59.000Z

157

Simulating Study of Premixed Charge Compression Ignition on Light-Duty Diesel Fuel Economy and Emissions Control  

SciTech Connect

We utilize the Powertrain Systems Analysis Toolkit (PSAT) combined with transient engine and aftertreatment component models to simulate the impact of premixed charge compression ignition (PCCI) on the fuel economy and emissions of light-duty (LD) diesel-powered conventional and hybrid electric vehicles (HEVs). Our simulated aftertreatment train consists of a diesel oxidation catalyst (DOC), lean NOx trap (LNT), and catalyzed diesel particulate filter (DPF). The results indicate that utilizing PCCI combustion significantly reduces fuel consumption and tailpipe emissions for the conventional diesel-powered vehicle with NOx and particulate emissions controls. These benefits result from a favorable engine speed-load distribution over the cycle combined with a corresponding reduction in the need to regenerate the LNT and DPF. However, the current PCCI technology appears to offer less potential benefit for diesel HEVs equipped with similar emissions controls. This is because PCCI can only be activated over a relatively small part of the drive cycle. Thus we conclude that future utilization of PCCI in diesel HEVs will require significant extension of the available speed-load range for PCCI and revision of current HEV engine management strategies before significant benefits can be realized.

Gao, Zhiming [ORNL] [ORNL; Daw, C Stuart [ORNL] [ORNL; Wagner, Robert M [ORNL] [ORNL

2012-01-01T23:59:59.000Z

158

In-Use Performance Comparison of Hybrid Electric, CNG, and Diesel...  

NLE Websites -- All DOE Office Websites (Extended Search)

Corporation DOE: U.S. Department of Energy DPF: diesel particulate filter EGR: exhaust gas recirculation EPA: U.S. Environmental Protection Agency 9 ERMD: Emissions Research &...

159

Real-Time Particulate Mass Measurements Pre and Post Diesel Particulat...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

2005deeranderson.pdf More Documents & Publications Advanced Radio Frequency-Based Sensors for Monitoring Diesel Particulate Filter Loading and Regeneration Real-Time...

160

Pollution duality in turbocharged heavy duty diesel engine  

Science Journals Connector (OSTI)

Diesel engine designers are faced with increasingly stringent social demands to reduce emissions while maintaining high performance. Several strategies are considered, such as the advanced fuel system, the cooled exhaust gas recirculation (EGR), the particulate filter, the NOx after-treatment, the oxidation catalyst, the advanced control techniques and the alternative combustion. These strategies have been tuned to achieve the lowest engine exhaust gas emissions. The major problem of diesel engine pollution is the NOx and soot formation. Their antagonistic evolution according to the air/fuel ratio is well-known, and requires a good compromise. In this article, a numerical investigation was carried out using the KIVA-3v code. The aim deals with the influence of some engine parameters on the performances and the pollutant (NOx-soot) formation of a turbocharged heavy duty direct injection diesel engine. The numerical simulations were achieved to capture independently the effects of engine operating parameters such as the fuel injection timing, the fuel injection duration, the piston bowl diameter and the EGR rate. The obtained results are discussed and some conclusions are developed.

M. Bencherif; A. Liazid; M. Tazerout

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Non-Destructive Neutron Imaging to Analyze Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE))

Non-destructive, non-invasive imaging is being employed in the laboratory to understand how soot, ash, and catalytic washcoat are deposited within a diesel particulate filter.

162

Cleaning Up Diesel Engines  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Other Mobile Sources Off-Road Diesel Equipment Heavy-Duty Diesel Trucks Diesel Ships, Trains PM 2.5 Emissions Trend PM 2.5 Emissions Trend California Emissions From the 2005...

163

Mass Flow Estimation with Model Bias Correction for a Turbocharged Diesel Engine  

E-Print Network (OSTI)

Mass Flow Estimation with Model Bias Correction for a Turbocharged Diesel Engine Tomás Polóni. Based on an augmented observable Mean Value En- gine Model (MVEM) of a turbocharged Diesel engine in the intake duct. Keywords: Diesel engine, Mass flow estimation, Bias estimation, Kalman filtering, Mean value

Johansen, Tor Arne

164

Adhesion of Acinetobacter venetianus to Diesel Fuel Droplets Studied with In Situ Electrochemical and Molecular Probes  

Science Journals Connector (OSTI)

...energy source. The diesel fuel (Esso Italiana) for diesel engine vehicles is composed of a mixture...5 mm2 s1 at 40C (). The diesel fuel was filtered through a 0...6-diamidino-2-phenylindole) staining (). O2 consumption rates. The strains were grown...

Franco Baldi; Nadica Ivos?evi?; Andrea Minacci; Milva Pepi; Renato Fani; Vesna Svetlic?i?; Vera Z?uti?

1999-05-01T23:59:59.000Z

165

Diesel exhaust treatment produces cyanide  

Science Journals Connector (OSTI)

Diesel exhaust treatment produces cyanide ... Studies at the Swiss Federal Technical Institute (ETH), Zurich, have produced results that, if confirmed by further research, could pose problems for the developers of catalytic converters that reduce emissions from diesel and leanburn gasoline engines. ... Use of low molecular weight olefins as reductants for selective removal of nitrogen oxides from exhaust gases, either by bleeding the olefins into the exhaust stream or blending them into the fuel itself, has attracted the interest of engine makers and regulatory agencies. ...

JOSEPH HAGGIN

1994-05-02T23:59:59.000Z

166

Summary of Swedish Experiences on CNG and "Clean" Diesel Buses  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

diesel (i.e. Euro II) with ox cat CNG buses in 1992 (Gothenburg); later also biogas Retrofit particulate filters (i.e. CRT TM ) in mid 1990's Environmental zones in...

167

Responses measured in the exhaled breath of human volunteers acutely exposed to ozone and diesel exhaust  

Science Journals Connector (OSTI)

Exhaled breath collection is used to identify and monitor inflammatory or oxidative components in breath. Exhaled breath sample collection is noninvasive and would greatly benefit human pollutant exposure research. We demonstrate the efficacy of exhaled breath collection and analysis in two human exposure studies to ozone (O3) and diesel exhaust, respectively. O3 study: we collected exhaled breath (gas phase) from healthy human volunteers (age 18–35 years, 12 subjects) immediately before and after exposure to filtered air or 0.4 ppm O3 for 2 h with and without intermittent exercise. Six subjects received antioxidant supplementation for 2 weeks before their O3 exposure, while the remaining six subjects received placebo treatments. We demonstrate increased amounts of non-polar carbonyls exhaled immediately post O3 exposure. The O3-induced increase in exhaled carbonyl concentrations was attenuated in the group receiving antioxidants. Our data demonstrate that exhaled exposure biomarkers can be measured in the breath gas phase in humans exposed to O3. Diesel study: we collected exhaled breath condensate (EBC; liquid phase) from healthy human volunteers (age 18–40 years; 10 subjects) immediately before, immediately after and 20 h post filtered air or diesel exhaust (106 ± 9 µg m?3) exposure. Clean air and diesel exposures were separated by 3 weeks to 6 months. We obtained reproducible intra-subject EBC volumes and total protein concentrations across our six collection time points. Diesel exposure did not affect either EBC volume or total protein concentrations. Our data demonstrated EBC volume and total protein reproducibility over several months. Volume and total protein concentration may serve as normalizing factors for other EBC constituents.

K Sawyer; J M Samet; A J Ghio; J D Pleil; M C Madden

2008-01-01T23:59:59.000Z

168

Effect of Lubricant on the Formation of Heavy-Duty Diesel Exhaust Nanoparticles  

Science Journals Connector (OSTI)

Effect of Lubricant on the Formation of Heavy-Duty Diesel Exhaust Nanoparticles ... The effect of lubricants on nanoparticle formation in heavy-duty diesel exhaust with and without a continuously regenerating diesel particulate filter (CRDPF) is studied. ... The fine particles in diesel exhaust contain solid material produced during combustion process and volatile organic and sulfur compounds converted to particle phase during the exhaust gas cooling and dilution. ...

Kati Vaaraslahti; Jorma Keskinen; Barouch Giechaskiel; Anu Solla; Timo Murtonen; Hannu Vesala

2005-09-22T23:59:59.000Z

169

Water Content in Biodiesel, Diesel, and Biodiesel–Diesel Blends  

Science Journals Connector (OSTI)

Water Content in Biodiesel, Diesel, and Biodiesel–Diesel Blends ... In what concerns road transportation, biodiesel is being considered a good alternative to conventional diesels. ...

Patricia Bogalhos Lucente Fregolente; Leonardo Vasconcelos Fregolente; Maria Regina Wolf Maciel

2012-05-17T23:59:59.000Z

170

Educating Consumers: New Content on Diesel Vehicles, Diesel Exhaust...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Educating Consumers: New Content on Diesel Vehicles, Diesel Exhaust Fluid, and Selective Catalytic Reduction Technologies on the AFDC Educating Consumers: New Content on Diesel...

171

Large Diesel Engine Lubrication  

Science Journals Connector (OSTI)

Centralized lubrication for slow-speed internal combustion engines ; Marine diesel engine lubrication ...

Hans Gaca; Jan Ruiter; Götz Mehr; Theo Mang

2014-01-01T23:59:59.000Z

172

Retrofit and Testing of a Pre-Turbo, Diesel Oxidation Catalyst on a Tier 0, SD60M Freight Locomotive Achieving Over 50% PM Reduction  

Energy.gov (U.S. Department of Energy (DOE))

Poster presentation at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

173

Renewable Diesel | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Renewable Diesel Renewable Diesel Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan....

174

Comparing the Performance of SunDiesel and Conventional Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

the Performance of SunDiesel and Conventional Diesel in a Light-Duty Vehicle and Engines Comparing the Performance of SunDiesel and Conventional Diesel in a Light-Duty Vehicle and...

175

Biodiesel Emissions Testing with a Modern Diesel Engine - Equipment Only: Cooperative Research and Development Final Report, CRADA Number CRD-10-399  

SciTech Connect

To evaluate the emissions and performance impact of biodiesel in a modern diesel engine equipped with a diesel particulate filter. This testing is in support of the Non-Petroleum Based Fuels (NPBF) 2010 Annual Operating Plan (AOP).

Williams, A.

2013-06-01T23:59:59.000Z

176

Diesel prices flat  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices flat The U.S. average retail price for on-highway diesel fuel saw no movement from last week. Prices remained flat at 3.89 a gallon on Monday, based on the weekly...

177

Diesel prices decrease  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices decrease The U.S. average retail price for on-highway diesel fuel fell to 4.05 a gallon on Monday. That's down 4.1 cents from a week ago, based on the weekly price...

178

Diesel prices increase  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices increase The U.S. average retail price for on-highway diesel fuel rose to 3.90 a gallon on Monday. That's up 3 cents from a week ago, based on the weekly price...

179

Diesel prices decrease  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices decrease The U.S. average retail price for on-highway diesel fuel fell to 3.88 a gallon on Monday. That's down a penny from a week ago, based on the weekly price...

180

Diesel prices decrease  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices decrease The U.S. average retail price for on-highway diesel fuel fell to 3.82 a gallon on Monday. That's down 2.1 cents from a week ago, based on the weekly price...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Diesel prices decrease  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices decrease The U.S. average retail price for on-highway diesel fuel fell to 3.87 a gallon on Monday. That's down 1.6 cents from a week ago, based on the weekly price...

182

Diesel prices decrease  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices decrease The U.S. average retail price for on-highway diesel fuel fell to 3.85 a gallon on Monday. That's down 2 cents from a week ago, based on the weekly price...

183

Effects of Gaseous Sulphuric Acid on Diesel Exhaust Nanoparticle Formation and Characteristics  

Science Journals Connector (OSTI)

Effects of Gaseous Sulphuric Acid on Diesel Exhaust Nanoparticle Formation and Characteristics ... Diesel exhaust gaseous sulphuric acid (GSA) concentrations and particle size distributions, concentrations, and volatility were studied at four driving conditions with a heavy duty diesel engine equipped with oxidative exhaust after-treatment. ... The submicrometer diesel exhaust particles are typically divided into two separate groups, which are frequently seen in exhaust particle number size distribution as separate modes, usually called as an accumulation or a soot mode and a nucleation mode. ...

Topi Rönkkö; Tero Lähde; Juha Heikkilä; Liisa Pirjola; Ulrike Bauschke; Frank Arnold; Hans Schlager; Dieter Rothe; Jaakko Yli-Ojanperä; Jorma Keskinen

2013-09-17T23:59:59.000Z

184

Oxygen Reactivity of Devolatilized Diesel Engine Particulates from Conventional and Biodiesel Fuels  

Science Journals Connector (OSTI)

Oxygen Reactivity of Devolatilized Diesel Engine Particulates from Conventional and Biodiesel Fuels ... Abatement of diesel particulates has led to an overall decrease in the fuel efficiency of diesel engines, and overcoming these losses has been one of the more challenging problems in exhaust aftertreatment. ... (16-18) Establishing a general physical basis for modeling diesel particulate oxidation is especially challenging because of the large variations in microscopic structure that it can have. ...

Andrea Strzelec; Todd J. Toops; C. Stuart Daw

2013-06-10T23:59:59.000Z

185

DOE Awarded Patent for Reformulated Diesel Fuel | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Awarded Patent for Reformulated Diesel Fuel Awarded Patent for Reformulated Diesel Fuel DOE Awarded Patent for Reformulated Diesel Fuel May 19, 2006 - 10:46am Addthis Available free of Licensing Fees, Cleaner for the Environment WASHINGTON, DC - The U.S. Department of Energy today announced that it has developed, patented, and made commercially available reformulated diesel fuels which when used can reduce nitrogen oxides up to 10% and particulate matter up to 22% compared to those currently available. The diesel fuel formulations covered under this patent will be commercially available for use without licensing or royalty fees. This reformulated diesel fuel patent resulted from research conducted by the U.S. Department of Energy, Oak Ridge National Laboratory and its subcontractors. "DOE's personnel continue to bring to the forefront technologies and

186

Electrically-Assisted Diesel Particulate Filter Regeneration  

Energy.gov (U.S. Department of Energy (DOE))

2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation

187

Durability of Diesel Engine Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE))

2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

188

Durability of Diesel Engine Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE))

2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C.

189

Durability of Diesel Engine Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE))

2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C.

190

Experimental Diesel Particulate Filter Capabilities at PNNL  

Energy.gov (U.S. Department of Energy (DOE))

Presentation given at DEER 2006, August 20-24, 2006, Detroit, Michigan. Sponsored by the U.S. DOE's EERE FreedomCar and Fuel Partnership and 21st Century Truck Programs.

191

Electrically-Assisted Diesel Particulate Filter Regeneration  

Energy.gov (U.S. Department of Energy (DOE))

2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

192

Durability of Diesel Engine Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE))

2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation

193

Neutron Imaging of Diesel Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

August 3 2009 Non-invasive, non-destructive technique based on attenuation of the neutron beam. Neutrons interact with nuclei and their scattering power does not vary in...

194

Diesel Particulate Filters: Market Introducution in Europe  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fixing PMG) max. 936 once - 04192004 min. 767 once - 05102004 Platinum Price Evolution in once over the 1996-2004 period max. 936 once - 04192004 min. 333 once...

195

Electrically-Assisted Diesel Particulate Filter Regeneration  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

partner for this project, has developed a DPF technology that utilizes electrical power to heat the DPF for regeneration, thereby greatly reducing the "fuel penalty". D P F...

196

Durability of Diesel Engine Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

AT data is FY10 work 11 Managed by UT-Battelle for the U.S. Department of Energy K IC fracture surface displays nodules in SiC- based material that are silicon rich RT and 500C...

197

Durability of Diesel Engine Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Strength values for honeycomb bars corrected for Moment of Inertia (MOI) * Increasing fracture toughness leads to increasing strength * It is easier to perform fracture toughness...

198

Durability of Diesel Engine Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

* Usual: R s E, ( strength) * Here: R K K IC E * Easier to perform fracture toughness tests than strength (less material and fewer samples) * Properties measured...

199

Experimental Diesel Particulate Filter Capabilities at PNNL  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Acknowledgments Acknowledgments Principal Contributors Principal Contributors PNNL - Micro-modeling Project z Heather Dillon z Gary Maupin z Tim Peters z Mark Steward z Nat...

200

Reduction of NOx emission on NiCrAl-Titanium Oxide coated direct injection diesel engine fuelled with radish (Raphanus sativus) biodiesel  

Science Journals Connector (OSTI)

The main aim of this study is the experimental investigation of single cylinder DI diesel engine with and without coating. Diesel and radish (Raphanus sativus) oil Methyl Ester are used as fuels and the results are compared to find the effect of biodiesel in a thermal barrier coating engine. For this purpose engine cylinder head valves and piston crown are coated with 100??m of nickel-chrome-aluminium bond coat and 450??m of TiO2 by the plasma spray method. Radish oil methyl ester is produced by the transesterification process method. From the experimental investigation slight increase in specific fuel consumption in thermal barrier coating engine is observed when compared with the uncoated engine whereas NOx HC Smoke and CO emissions decreased with coated engine for all test fuels used in the coated engine when compared with that of the uncoated engine.

V. Ravikumar; D. Senthilkumar

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Low-Load Dual-Fuel Compression Ignition (CI) Engine Operation with an On-Board Reformer and a Diesel Oxidation Catalyst: Effects on Engine Performance and Emissions  

Science Journals Connector (OSTI)

Ideally, homogeneous air fuel mixtures ignited spontaneously exhibit less pollutants and can improve engine efficiency compared to standard diesel combustion, which is based on diffusion combustion. ... Although optimization of the injection timing of the in-cylinder DI fuel (e.g., diesel) aims to ignite the mixture and control the start of combustion (SOC) for the different premixed fuel ratios, the fuel ignition timing is complicated and problematic for a dual-fueled engine under a number of engine-operating conditions (e.g., low loads and use of residual gas trapping). ... Deactivation due to coking of a single Ni/Pt-based catalyst is significant, but operation using a platinum-ceria catalyst in line with a Ni-based steam-reforming catalyst allows acceptable efficiencies. ...

A. Tsolakis; R. Torbati; A. Megaritis; A. Abu-Jrai

2009-10-07T23:59:59.000Z

202

Low emissions diesel fuel  

DOE Patents (OSTI)

A method and matter of composition for controlling NO.sub.x emissions from existing diesel engines. The method is achieved by adding a small amount of material to the diesel fuel to decrease the amount of NO.sub.x produced during combustion. Specifically, small amounts, less than about 1%, of urea or a triazine compound (methylol melamines) are added to diesel fuel. Because urea and triazine compounds are generally insoluble in diesel fuel, microemulsion technology is used to suspend or dissolve the urea or triazine compound in the diesel fuel. A typical fuel formulation includes 5% t-butyl alcohol, 4.5% water, 0.5% urea or triazine compound, 9% oleic acid, and 1% ethanolamine. The subject invention provides improved emissions in heavy diesel engines without the need for major modifications.

Compere, Alicia L. (Knoxville, TN); Griffith, William L. (Oak Ridge, TN); Dorsey, George F. (Farragut, TN); West, Brian H. (Kingston, TN)

1998-01-01T23:59:59.000Z

203

The influence of propylene glycol ethers on base diesel properties and emissions from a diesel engine  

Science Journals Connector (OSTI)

Abstract The oxygenated additives propylene glycol methyl ether (PGME), propylene glycol ethyl ether (PGEE), dipropylene glycol methyl ether (DPGME) were studied to determine their influence on both the base diesel fuel properties and the exhaust emissions from a diesel engine (CO, NOx, unburnt hydrocarbons and smoke). For diesel blends with low oxygen content (?4.0 wt.%), the addition of these compounds to base diesel fuel decreases aromatic content, kinematic viscosity, cold filter plugging point and Conradson carbon residue. Also, each compound modifies the distillation curve at temperatures below the corresponding oxygenated compound boiling point, the distillate percentage being increased. The blend cetane number depends on the type of propylene glycol ether added, its molecular weight, and the oxygen content of the fuel. The addition of PGME decreased slightly diesel fuel cetane number, while PGEE and DPGME increased it. Base diesel fuel-propylene glycol ether blends with 1.0 and 2.5 wt.% oxygen contents were used in order to determine the performance of the diesel engine and its emissions at both full and medium loads and different engine speeds (1000, 2500 and 4000 rpm). In general, at full load and in comparison with base diesel fuel, the blends show a slight reduction of oxygen-free specific fuel consumption. CO emissions are reduced appreciably for 2.5 wt.% of oxygen blends, mainly for PGEE and DPGME. \\{NOx\\} emissions are reduced slightly, but not the smoke. Unburnt hydrocarbon emissions decrease at 1000 and 2500 rpm, but not at 4000 rpm. At medium load, the effect of the additives is much less significant, due to the fact that the ratio oxygen from additive/oxygen from air is much lower.

F. Gómez-Cuenca; M. Gómez-Marín; M.B. Folgueras-Díaz

2013-01-01T23:59:59.000Z

204

Analysis of C1, C2, and C10 through C33 particle-phase and semi-volatile organic compound emissions from heavy-duty diesel engines  

E-Print Network (OSTI)

from heavy-duty diesel engines Z. Gerald Liu a,*, Devin R. Berg a , Victoria N. Vasys a , Melissa E engines Aftertreatment technology Diesel particulate filter Chemical speciation a b s t r a c t To meet increasingly stringent regulations for diesel engines, technologies such as combustion strategies

Wu, Mingshen

205

Marine Diesel Engines  

Science Journals Connector (OSTI)

Marine diesel engines need reserve power to compensate for ... and decreased efficiency of the engine caused by wear and contamination. Minimum efficiency reserves must be...

Michael Palocz-Andresen

2013-01-01T23:59:59.000Z

206

Engine-External HC-Dosing for Regeneration of Diesel Particulate...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

for Heavy Duty and NRMM According to Annex XXVII StVZO This presentation discusses how a diesel particulate filter can be integrated in the exhaust piping of a heavy-duty engine....

207

Gasoline and Diesel Fuel Update  

NLE Websites -- All DOE Office Websites (Extended Search)

Diesel Fuel Pump Components History WHAT WE PAY FOR IN A GALLON OF DIESEL FUEL Mon-yr Retail Price (Dollars per gallon) Refining (percentage) Distribution & Marketing (percentage)...

208

Method for reducing pressure drop through filters, and filter exhibiting reduced pressure drop  

DOE Patents (OSTI)

Methods for generating and applying coatings to filters with porous material in order to reduce large pressure drop increases as material accumulates in a filter, as well as the filter exhibiting reduced and/or more uniform pressure drop. The filter can be a diesel particulate trap for removing particulate matter such as soot from the exhaust of a diesel engine. Porous material such as ash is loaded on the surface of the substrate or filter walls, such as by coating, depositing, distributing or layering the porous material along the channel walls of the filter in an amount effective for minimizing or preventing depth filtration during use of the filter. Efficient filtration at acceptable flow rates is achieved.

Sappok, Alexander; Wong, Victor

2014-11-18T23:59:59.000Z

209

Optimization of combustion bowl geometry for the operation of kapok biodiesel – Diesel blends in a stationary diesel engine  

Science Journals Connector (OSTI)

Abstract The purpose of this research work is to optimize the combustion bowl geometry of a single cylinder stationary diesel engine for the effective operation of KME (kapok methyl ester) – diesel blends. Considering that the reported design modification would render the benefit of adaptation of higher blends of KME, in this study, two different combustion chamber geometries such as TRCC (trapezoidal combustion chamber) and TCC (toroidal combustion chamber) were chosen in addition to the convention design of HCC (hemispherical combustion chamber). In the experimental investigation, suitable blends such as B25 (25% KME + 75% diesel), B50 (50% KME + 50% diesel), B75 (75% KME + 25% diesel) and B100 (100% KME) were tested in a diesel engine with various combustion chamber geometries as mentioned above. Based on the results obtained from this study, TCC was shown to exhibit better performance and emission than TRCC and HCC for all test blends. Further, when compared to diesel, B25 and B50 were found to be the optimum blends with HCC and TCC, respectively, while TRCC seldom evinced better engine characteristics for any of the blends. Categorically, B50 showed a 5.2% increase in BTE (brake thermal efficiency) than diesel with TCC, whereas emissions such as CO (carbon monoxide) and smoke were reduced by 15.7% and 7.8%, respectively, with a comparable NOX (nitrogen oxides) emission with diesel. Similarly, combustion for B50 with TCC was found to be better than diesel, manifesting an increase in maximum heat release rate that that of diesel. Conclusively, from the experimental study, TCC was recognized as an ideal choice of combustion chamber design for the operation of blends up to B50 in a diesel engine.

S. Vedharaj; R. Vallinayagam; W.M. Yang; C.G. Saravanan; P.S. Lee

2015-01-01T23:59:59.000Z

210

IMPACT OF OXYGENATED FUEL ON DIESEL ENGINE PERFORMANCE AND EMISSIONS  

SciTech Connect

As evidenced by recent lawsuits brought against operators of large diesel truck fleets [1] and by the Consent Decree brought against the heavy-duty diesel manufacturers [2], the environmental and health effects of diesel engine emissions continue to be a significant concern. Reduction of diesel engine emissions has traditionally been achieved through a combination of fuel system, combustion chamber, and engine control modifications [3]. Catalytic aftertreatment has become common on modern diesel vehicles, with the predominant device being the diesel oxidation catalytic converter [3]. To enable advanced after-treatment devices and to directly reduce emissions, significant recent interest has focused on reformulation of diesel fuel, particularly the reduction of sulfur content. The EPA has man-dated that diesel fuel will have only 15 ppm sulfur content by 2007, with current diesel specifications requiring around 300 ppm [4]. Reduction of sulfur will permit sulfur-sensitive aftertreatment devices, continuously regenerating particulate traps, NOx control catalysts, and plasma assisted catalysts to be implemented on diesel vehicles [4]. Another method of reformulating diesel fuel to reduce emissions is to incorporate oxygen in the fuel, as was done in the reformulation of gasoline. The use of methyl tertiary butyl ether (MTBE) in reformulated gasoline has resulted in contamination of water resources across the country [5]. Nonetheless, by relying on the lessons learned from MTBE, oxygenation of diesel fuel may be accomplished without compromising water quality. Oxygenation of diesel fuel offers the possibility of reducing particulate matter emissions significantly, even for the current fleet of diesel vehicles. The mechanism by which oxygen content leads to particulate matter reductions is still under debate, but recent evidence shows clearly that ''smokeless'' engine operation is possible when the oxygen content of diesel fuel reaches roughly 38% by weight [6]. The potential improvements in energy efficiency within the transportation section, particularly in sport utility vehicles and light-duty trucks, that can be provided by deployment of diesel engines in passenger cars and trucks is a strong incentive to develop cleaner burning diesel engines and cleaner burning fuels for diesel engines. Thus, serious consideration of oxygenated diesel fuels is of significant practical interest and value to society. In the present work, a diesel fuel reformulating agent, CETANERTM, has been examined in a popular light-medium duty turbodiesel engine over a range of blending ratios. This additive is a mixture of glycol ethers and can be produced from dimethyl ether, which itself can be manufactured from synthesis gas using Air Products' Liquid Phase Dimethyl Ether (LPDME TM) technology. CETANERTM is a liquid, has an oxygen content of 36 wt.%, has a cetane number over 100 and is highly miscible in diesel fuel. This combination of physical and chemical properties makes CETANERTM an attractive agent for oxygenating diesel fuel. The present study considered CETANERTM ratios from 0 to 40 wt.% in a California Air Resources Board (CARB) specification diesel fuel. Particulate matter emissions, gaseous emissions and in-cylinder pressure traces were monitored over the AVL 8-Mode engine test protocol [7]. This paper presents the results from these measurements and discusses the implications of using high cetane number oxygenates in diesel fuel reformulation.

Boehman, Andre L.

2000-08-20T23:59:59.000Z

211

Diesel engine reference book  

SciTech Connect

This book is a reference on the design, operation, and maintenance of all types of diesel engines, ranging from the smallest automotive and ancillary engines to the largest marine diesels. Nearly 900 line drawings, graphs and photos illustrate the book. Major Sections: Theory; Engine Design Practice; Lubrication; Environmental Pollution; Crankcase Explosions; Engine Types; Engine Testing; Maintenance; Index.

Lilly, I.R.C.

1984-01-01T23:59:59.000Z

212

Protective effects of pulmonary epithelial lining fluid on oxidative stress and DNA single-strand breaks caused by ultrafine carbon black, ferrous sulphate and organic extract of diesel exhaust particles  

SciTech Connect

Pulmonary epithelial lining fluid (ELF) is the first substance to make contact with inhaled particulate matter (PM) and interacts chemically with PM components. The objective of this study was to determine the role of ELF in oxidative stress, DNA damage and the production of proinflammatory cytokines following physicochemical exposure to PM. Ultrafine carbon black (ufCB, 15 nm; a model carbonaceous core), ferrous sulphate (FeSO{sub 4}; a model transition metal) and a diesel exhaust particle (DEP) extract (a model organic compound) were used to examine the acellular oxidative potential of synthetic ELF and non-ELF systems. We compared the effects of exposure to ufCB, FeSO{sub 4} and DEP extract on human alveolar epithelial Type II (A549) cells to determine the levels of oxidative stress, DNA single-strand breaks and interleukin-8 (IL-8) production in ELF and non-ELF systems. The effects of ufCB and FeSO{sub 4} on the acellular oxidative potential, cellular oxidative stress and DNA single-strand breakage were mitigated significantly by the addition of ELF, whereas there was no decrease following treatment with the DEP extract. There was no significant effect on IL-8 production following exposure to samples that were suspended in ELF/non-ELF systems. The results of the present study indicate that ELF plays an important role in the initial defence against PM in the pulmonary environment. Experimental components, such as ufCB and FeSO{sub 4}, induced the production of oxidative stress and led to DNA single-strand breaks, which were moderately prevented by the addition of ELF. These findings suggest that ELF plays a protective role against PM-driven oxidative stress and DNA damage. -- Highlights: ? To determine the role of ELF in ROS, DNA damage and IL-8 after exposure to PM. ? ufCB, FeSO{sub 4} and DEP extract were used to examine the protective effects of ELF. ? PM-driven oxidative stress and DNA single-strand breakage were mitigated by ELF. ? The findings suggest that ELF has a protective role against PM. ? The synthetic ELF system could reduce the use of animals in PM-driven ROS testing.

Chuang, Hsiao-Chi [School of Respiratory Therapy, College of Medicine, Taipei Medical University, Taipei, Taiwan (China) [School of Respiratory Therapy, College of Medicine, Taipei Medical University, Taipei, Taiwan (China); Division of Pulmonary Medicine, Department of Internal Medicine, Shuang Ho Hospital, Taipei Medical University, Taipei, Taiwan (China); Cheng, Yi-Ling; Lei, Yu-Chen [Institute of Occupational Medicine and Industrial Hygiene, College of Public Health, National Taiwan University, Taipei, Taiwan (China)] [Institute of Occupational Medicine and Industrial Hygiene, College of Public Health, National Taiwan University, Taipei, Taiwan (China); Chang, Hui-Hsien [Institute of Environmental Health, College of Public Health, National Taiwan University, Taipei, Taiwan (China)] [Institute of Environmental Health, College of Public Health, National Taiwan University, Taipei, Taiwan (China); Cheng, Tsun-Jen, E-mail: tcheng@ntu.edu.tw [Institute of Occupational Medicine and Industrial Hygiene, College of Public Health, National Taiwan University, Taipei, Taiwan (China) [Institute of Occupational Medicine and Industrial Hygiene, College of Public Health, National Taiwan University, Taipei, Taiwan (China); Department of Public Health, College of Public Health, National Taiwan University, Taipei, Taiwan (China)

2013-02-01T23:59:59.000Z

213

Argonne Transportation - Diesel Award  

NLE Websites -- All DOE Office Websites (Extended Search)

Team Receives DOE Award for Groundbreaking Diesel Fuel Spray Research Team Receives DOE Award for Groundbreaking Diesel Fuel Spray Research Jin Wang, Chris Powell, Yong Yue, and Steve Ciatti Recent DOE Award winners, (L-R) Jin Wang, Chris Powell, Yong Yue, and Steve Ciatti, stand in front of their fuel spray injection chamber. Using the synchrotron beam at the APS, the team is able to probe the fuel spray and study the process of combustion. A team of Argonne scientists (Jin Wang, Steve Ciatti, Chris Powell, and Yong Yue) recently won the 2002 National Laboratory Combustion and Emissions Control R&D Award for groundbreaking work in diesel fuel sprays. For the first time ever, the team used x-rays to penetrate through gasoline and diesel sprays and made detailed measurements of fuel injection systems for diesel engines. This technology uncovered a previously unknown

214

Diesel fuel oils, 1980  

SciTech Connect

Properties of diesel fuels produced during 1980 were submitted for study and compilation under a cooperative agreement between the Department of Energy, Bartlesville Energy Technology Center, Bartlesville, Oklahoma and the American Petroleum Institute. Tests of 192 samples of diesel fuel oils from 95 refineries throughout the country were made by 28 petroleum groups according to type of diesel fuel. Each group of analyses is subdivided into five tabulations according to five general regions of the country where the fuels are marketed. The regions, containing a total of 16 districts, are shown on a map in the report. Data from 13 laboratory tests on each individual diesel fuel sample are listed and arranged by geographic marketing districts in decreasing order of sales volumes. Charts are included showing trends of averages of certain properties for the four types of diesel fuels for the years 1960-1980. Summaries of the results of the 1980 survey, compared with similar data for 1979, are shown.

Shelton, E.M.

1980-12-01T23:59:59.000Z

215

Rational Catalyst Design Applied to Development of Advanced Oxidation...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Catalyst Design Applied to Development of Advanced Oxidation Catalysts for Diesel Emission Control Rational Catalyst Design Applied to Development of Advanced Oxidation...

216

Simulating the Impact of Premixed Charge Compression Ignition on Light-Duty Diesel Fuel Economy and Emissions of Particulates and NOx  

SciTech Connect

We utilize the Powertrain Systems Analysis Toolkit (PSAT) combined with transient engine and aftertreatment component models implemented in Matlab/Simulink to simulate the effect of premixed charge compression ignition (PCCI) on the fuel economy and emissions of light-duty diesel-powered conventional and hybrid electric vehicles (HEVs). Our simulated engine is capable of both conventional diesel combustion (CDC) and premixed charge compression ignition (PCCI) over real transient driving cycles. Our simulated aftertreatment train consists of a diesel oxidation catalyst (DOC), lean NOx trap (LNT), and catalyzed diesel particulate filter (DPF). The results demonstrate that, in the simulated conventional vehicle, PCCI can significantly reduce fuel consumption and emissions by reducing the need for LNT and DPF regeneration. However, the opportunity for PCCI operation in the simulated HEV is limited because the engine typically experiences higher loads and multiple stop-start transients that are outside the allowable PCCI operating range. Thus developing ways of extending the PCCI operating range combined with improved control strategies for engine and emissions control management will be especially important for realizing the potential benefits of PCCI in HEVs.

Gao, Zhiming [ORNL; Daw, C Stuart [ORNL; Wagner, Robert M [ORNL; Edwards, Kevin Dean [ORNL; Smith, David E [ORNL

2013-01-01T23:59:59.000Z

217

Influence of Diesel Engine Combustion Parameters on Primary Soot Particle Diameter  

Science Journals Connector (OSTI)

In addition to minimized engine-out emissions, exhaust gas after-treatment systems such as diesel particle filter and chemical reduction of NOx will be necessary to meet the U.S. Federal (EPA) 2007 emission standards for heavy-duty diesel engines. ... While for the diesel fuel a reduction of the number of particles in the accumulation mode went in line with a shift of the mode diameter toward smaller values (see Figures 2 and 3), this was not a general observation for the water?diesel emulsion fuel. ... JSME International Journal, Series B: Fluids and Thermal Engineering (2001), 44 (1), 166-170 CODEN: JIJEEE; ISSN:1340-8054. ...

Urs Mathis; Martin Mohr; Ralf Kaegi; Andrea Bertola; Konstantinos Boulouchos

2005-02-04T23:59:59.000Z

218

Thermal stability of diesel fuels by quantitative gravimetric JFTOT  

SciTech Connect

The current worldwide standard test method for assessing thermal stability of jet turbine aviation fuels is the ASTM D3241 method. This method generates a visual tube deposit rating which is not quantitative, but assumes that very dark colors equate to unstable fuels. The tube rating is coded against color standards and the darkest color is usually said to fail a fuel for use in jet turbine engines/fuel systems. The method also generates a semi-quantitative filter pressure drop. The pressure drop is so semi-quantitative that it also is afforded a pass/fail criterion for fuel acceptance in jet aircraft. In 1991, we described the construction of a test device which duplicated all of the experimentally important parameters of the D3241 method but which substituted a weighable 302 stainless steel (s/s) foil strip for the bulky tube, so that direct weighing of thermal surface deposits could be made. In addition, the nominal 17 micron (dutch weave) s/s filter of the D3241 was substituted with a nylon membrane 0.8 micron filter which was also capable of direct weighing of the fuel entrained solids generated by the test. In subsequent papers, the use of this device for generating a large data base of results based on aviation fuels from many different refinery processes and many different geographic/crude sources was described. In addition this new device, dubbed the gravimetric jet fuel total oxidation tester (JFTOT) after the original ASTM D3241 device, was also used to assess quantitatively the effects of temperature, pressure, and fuel flow in addition to the effects of dissolved metals and various fuel additives. This paper describes the JFTOT test for the analysis of middle distillate diesel fuels.

Beal, E.J.; Hardy, D.R. [Naval Research Laboratory, Washington, DC (United States)

1994-12-31T23:59:59.000Z

219

HEALTH EFFECTS OF DIESEL EXHAUST: AN HEI PERSPECTIVE  

SciTech Connect

Diesel engines have many advantages, including good fuel economy, power, durability, lower emissions of some pollutants (such as carbon monoxide) and of carbon dioxide (a greenhouse gas). However, there are a number of concerns that need to be addressed: (1) emissions of nitrogen oxides (which contribute to ozone formation) and of particulate matter (PM); (2) questions about cancer and other health effects from exposure to diesel PM; and (3) as efforts to decrease emissions progress, a need to understand whether the nature and toxicity of the PM emitted has changed. This paper focuses on (1) carcinogenicity data, (2) noncancer effects, and (3) diesel as part of the complex ambient mixture of PM.

Warren, Jane

2000-08-20T23:59:59.000Z

220

Diesel Technology - Challenges & Opportunities for North America  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

diesel entries Passenger car and Class 1 truck diesel sales fall off quickly as diesel fuel price advantage disappears, overall fuel costs drop, and fuel rationing ceases ...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

(1) Elements of Diesel Engineering: (2) Diesel and other Internal-Combustion Engines: (3) Diesel Engines  

Science Journals Connector (OSTI)

... publications arising from its importance from scientific, technical and commercial points of view, the Diesel ...

1937-01-30T23:59:59.000Z

222

Experimental investigation on thermal barrier coated diesel engine fueled with diesel-biodiesel-ethanol-diethyl ether blends  

Science Journals Connector (OSTI)

In the present work diesel-biodiesel-ethanol (DBE) and diesel-biodiesel-diethyl ether (DBD) fuels are tested with normal diesel engine and the diesel engine coated with the layers of aluminum oxide (Al 2O3) of 0.3?mm and yttria-stabilized zirconia of 0.2?mm. The various performance and emission parameters are analyzed and determined. The experimental work was carried out in a single cylinder water cooled engine coupled with eddy current dynamometer. The AVL make five gas analyzer and smoke meter were used to measure the different exhaust pollutants. The result shows that the brake thermal efficiency of coated engine is more than that of base diesel at high loads. The thermal barrier coated engine using fuel as diesel biodiesel and ethanol (TDBE) produces the lowest carbon monoxide (CO) emissions among all the fuels that are selected. In addition it produces the lowest carbon dioxide (CO2) at higher loads. Both the thermal barrier coated engine using fuel as diesel biodiesel and diethyl ether (TDBD) and TDBE have higher NOx emissions among almost all the fuels used. The TDBE and TDBD have higher smoke emissions at initial loads but eventually show lower smoke emissions at higher loads. The thermal barrier coated diesel engine fueled with DBE and DBD shows an increase in engine power and specific fuel consumption as well as significant improvements in exhaust gas emissions except NOx.

2013-01-01T23:59:59.000Z

223

Advanced diesel combustion  

Science Journals Connector (OSTI)

Future emission norms will further reduce the vehicle emissions of diesel engines. To meet the goal of achieving these stringent limits while maintaining attractive attributes of marketability, the combustion ...

Dirk Adolph; Hartwig Busch; Stefan Pischinger; Andreas Kolbeck…

2008-01-01T23:59:59.000Z

224

diesel.vp  

U.S. Energy Information Administration (EIA) Indexed Site

differences, whereas stationary series can be estimated in level form. The unit root test could not reject the hypothesis that the retail and spot diesel fuel price series have...

225

Reaction Profiles during Exhaust-Assisted Reforming of Diesel Engine Fuels  

Science Journals Connector (OSTI)

Reaction Profiles during Exhaust-Assisted Reforming of Diesel Engine Fuels ... The reforming efficiency was dependent on the fuel type and followed the general trend of bioethanol > rapeseed methyl ester > low-sulfur diesel fuel. ... The use of exhaust gas recirculation (EGR) in diesel engines reduces nitrogen oxide (NOx) emissions but results in an increased release of smoke and particulate matter (PM), as well as higher fuel consumption. ...

A. Tsolakis; A. Megaritis; S. E. Golunski

2005-03-10T23:59:59.000Z

226

Making premium diesel fuel  

SciTech Connect

For refiners, extra processing and blending is a practical, though not always easy, option for improving diesel fuel properties; however, it entails compromises. For example, ignition quality can be improved by including more paraffins, but this negatively impacts the required low-temperature operability properties. Another example is adding aromatics to increase the diesel`s Btu value, but aromatics burn poorly and tend to cause smoking. Due to these and other types of diametrical trade-offs, the scope of distillate processing and fuels blending at the refinery is often very limited. Therefore, fuel additives are rapidly becoming the only alternative for obtaining the superior quality necessary in a premium diesel fuel. If stabilizers, dispersants and other fuel additive components are used in the additive package, the product can be marketed as a premium diesel fuel additive. Engines using this additive-treated fuel will consistently have less emissions, produce optimum power from the fuel energy conversion process and perform to design specifications. And the user will truly have a premium diesel fuel. The paper discusses detergent additives, cetane or ignition improvers, fuel stabilizers, cold weather additives, and lubricity additives.

Pipenger, G. [Amalgamated Inc., Fort Wayne, IN (United States)

1997-02-01T23:59:59.000Z

227

Characterization and analysis of diesel exhaust odor  

Science Journals Connector (OSTI)

Characterization and analysis of diesel exhaust odor ... Carbonyl and Nitrogen Dioxide Emissions From Gasoline- and Diesel-Powered Motor Vehicles ...

Patricia A. Partridge; Francis J. Shala; Nicholas P. Cernansky; Irwin H. Suffet

1987-04-01T23:59:59.000Z

228

Preserving Diesel Exhaust Ultrafine (Nano-) Particulate Structure...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Preserving Diesel Exhaust Ultrafine (Nano-) Particulate Structure in Genotoxicity Studies to Support Engineering Development of Emission Controls Preserving Diesel Exhaust...

229

Numerical Modeling and Experimental Study of Combustion and Soot Formation in a Direct Injection Diesel Engine  

Science Journals Connector (OSTI)

Numerical Modeling and Experimental Study of Combustion and Soot Formation in a Direct Injection Diesel Engine ... The major problems associated with diesel engines are the high levels of nitrogen oxides (NOX) and particulate emissions. ... (11)?Flagan, R. C.; Seinfeld, J. H. Fundamentals of Air Pollution Engineering; Prentice Hall Inc.:? New York, 1988. ...

T. L. Chan; X. B. Cheng

2007-04-10T23:59:59.000Z

230

Just the Basics: Diesel Engine  

NLE Websites -- All DOE Office Websites (Extended Search)

Today's direct-injection diesel Today's direct-injection diesel engines are more rugged, powerful, durable, and reliable than gasoline engines, and use fuel much more efficiently, as well. Diesel Engines Yesterday, Today, and Tomorrow Diesels are workhorse engines. That's why you find them powering heavy- duty trucks, buses, tractors, and trains, not to mention large ships, bulldozers, cranes, and other construction equipment. In the past, diesels fit the stereotype of muscle-bound behe- moths. They were dirty and sluggish, smelly and loud. That image doesn't apply to today's diesel engines, however, and tomorrow's diesels will show even greater improvements. They will be even more fuel efficient, more flexible in the fuels they can use, and also much cleaner in emissions. How Diesel Engines Work

231

Diesel prices continue to increase  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices continue to increase The U.S. retail price for on-highway diesel fuel rose to its highest average since September at 3.95 a gallon. That's up 4.7 cents from a week...

232

Diesel prices continue to increase  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices continue to increase The U.S. average retail price for on-highway diesel fuel rose to 3.91 a gallon on Monday. That's up 7-tenths of a penny from a week ago, based...

233

Diesel prices continue to increase  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices continue to increase The U.S. average retail price for on-highway diesel fuel rose to 3.98 a gallon. That's up 2.6 cents from a week ago, based on the weekly price...

234

Oil Bypass Filter Technology Evaluation Ninth Quarterly Report October–December 2004  

SciTech Connect

This Oil Bypass Filter Technology Evaluation quarterly report (October–December 2004) details the ongoing fleet evaluation of oil bypass filter technologies being conducted by the Idaho National Laboratory (INL; formerly Idaho National Engineering and Environmental Laboratory) for the U.S. Department of Energy’s FreedomCAR & Vehicle Technologies Program. Eight INL four-cycle diesel-engine buses used to transport INL employees on various routes and six INL Chevrolet Tahoes with gasoline engines are equipped with oil bypass filter systems from the puraDYN Corporation. This quarter, three additional buses were equipped with bypass filters from Refined Global Solutions. Oil bypass filters are reported to have an engine oil filtering capability of less than 1 micron. Both the puraDYN and Refined Global Solutions bypass filters have a heating chamber to remove liquid contaminate from the oil. During the quarter, the eleven diesel engine buses traveled 62,188 miles, and as of January 3, 2005 the buses had accumulated 643,036 total test miles. Two buses had their engine oil changed this quarter. In one bus, the oil was changed due to its degraded quality as determined by a low total base number (<3.0 mg KOH/g). The other bus had high oxidation and nitration numbers (>30.0 Abs/cm). Although a total of six buses have had their oil changed during the last 26 months, by using the oil bypass filters the buses in the evaluation avoided 48 oil changes, which equates to 1,680 quarts (420 gallons) of new oil not consumed and 1,680 quarts of waste oil not generated. Therefore, over 80% of the oil normally required for oil-changes was not used, and, consequently, the evaluation achieved over 80% reduction in the amount of waste oil normally generated. The six Tahoe test vehicles traveled 39,514 miles, and as of January 3, 2005 the Tahoes had accumulated 189,970 total test miles. The Tahoe filter test is in transition. To increase the rate of bypass filter oil flow on the Tahoes, puraDYN provided a larger orifice assembly, and these are being changed out as the Tahoes come in for regular service.

Larry Zirker; James Francfort; Jordan Fielding

2005-02-01T23:59:59.000Z

235

Diesel fuel oils, 1982  

SciTech Connect

Properties of diesel fuels produced during 1982 were submitted for study and compilation under a cooperative agreement between the Department of Energy (DOE), Bartlesville Energy Technology Center (BETC), Bartlesville, Oklahoma and the American Petroleum Institute (API). Tests of 184 samples of diesel fuel oils from 83 refineries throughout the country were made by 27 petroleum groups according to type of diesel fuel. Each group of analyses is subdivided into five tabulations according to five general regions of the country where the fuels are marketed. The regions, containing a total of 16 districts, are shown on a map in the report. Data from 13 laboratory tests on each individual diesel fuel sample are listed and arranged by geographic marketing districts in decreasing order of sales volumes. Charts are included showing trends of averages of certain properties for the four types of diesel fuels for the years 1960 to 1982. Summaries of the results of the 1982 survey, compared with similar data for 1981, are shown in Tables 1 through 4 of the report. A summary of 1-D and 2-D fuels are presented in Tables 5 and 6 respectively.

Shelton, E.M.

1982-11-01T23:59:59.000Z

236

Diesel fuel oils, 1981  

SciTech Connect

Properties of diesel fuels produced during 1981 were submitted for study and compilation under a cooperative agreement between the Department of Energy (DOE), Bartlesville Energy Technology Center (BETC), Bartlesville, Oklahoma and the American Petroleum Institute (API). Tests of 160 samples of diesel fuel oils from 77 refineries throughout the country were made by 26 petroleum groups according to type of diesel fuel. Each group of analyses is subdivided into five tabulations according to five general regions of the country where the fuels are marketed. The regions, containing a total of 16 districts, are shown on a map in the report. Data from 13 laboratory tests on each individual diesel fuel sample are listed and arranged by geographic marketing districts in decreasing order of sales volumes. Charts are included showing trends of averages of certain properties for the four types of diesel fuels for the years 1960 to 1981. Summaries of the results of the 1981 survey, compared with similar data for 1980, are shown.

Shelton, E.M.

1981-12-01T23:59:59.000Z

237

Soybean Oil as Diesel Fuel  

Science Journals Connector (OSTI)

Soybean Oil as Diesel Fuel ... TESTS are reported from Japan on the use of soybean oil as Diesel fuel in a 12-horsepower engine of 150-mm. ... This trouble was overcome by passing through some of the Diesel cooling water to heat the fuel tank and supply line. ...

C.H.S. TUPHOLME

1940-10-10T23:59:59.000Z

238

Oxidation of NO in Sample Bags to Yield NO2 | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Electrostatic Neutralization - A Key to Accurate & Repeatable PM Filter Weighing Urea SCR and DPF System for Diesel Sport Utility Vehicle Meeting Tier II Bin 5 DOE and Ford...

239

Experimental investigations on diesel engine fuelled with methyl esters of cotton seed oil  

Science Journals Connector (OSTI)

In this investigation, cotton seed methyl ester (CSME) was prepared by transesterification using potassium hydroxide (KOH) as catalyst. The engine performance was analysed with different blends of biodiesel and was compared with neat diesel. It was concluded that the lower blends of biodiesel are closer to diesel as far as thermal efficiency is concerned. In the lower blends, the brakes specific fuel consumption is also comparatively reduced. The smoke density also increases for the blends of methyl ester of cotton seed oil diesel compared to neat diesel operation. The oxides of nitrogen (NOx) emission level are decreased with the blends of methyl ester of cotton seed oil compared to neat diesel. The results proved that the use of biodiesel (produced from cotton seed oil) in compression ignition engine is a viable alternative to diesel.

M. Saravanan; A. Anbarasu; M. Loganathan

2013-01-01T23:59:59.000Z

240

Tailoring key fuel properties of diesel–biodiesel–ethanol blends for diesel engine  

Science Journals Connector (OSTI)

Alternative fuel research for the profusely growing number of diesel run automotive has intensified due to environmental reasons and turmoil in petroleum market. Government initiatives all around the world, their energy policies and steps to emphasis the use of biodiesel; proved biodiesel as a number one renewable substitute for No. 2 diesel fuels. Among all biodiesel feedstock, palm oil is a potential source with higher yield rate without much fertilizer use especially in tropical region. However, the application of transesterified palm biodiesel is objected by many auto-manufacturers due to adverse effects on engine in long term operation. The aim of this study was to modify the key fuel properties of palm biodiesel which causes engine fouling in long term operation. A significant amount of work is devoted to mix biodiesel and diesel at arbitrary percentages and test engine performance. Numerous fuel additives are developed for biodiesels automotive use. In this study, chemical properties of biodiesel are tailored by ethanol and an optimum formulation is derived mathematically. Ethanol is used at a controlled proportion (6%) with palm oil methyl ester (POME) as additive to reduce the higher viscosity of POME. This optimum palm biodiesel–ethanol blend was mixed at varying proportions (i.e. 0–30%) with No. 2 diesel to produce ternary blends of diesel–palm biodiesel–ethanol. Cold flow properties (such as, could point, pour point) of these ternary blends has improved and minute percentage of ethanol adding did not adversely affect the oxidation stability and corrosiveness of the fuel blend. Ethanol has significantly reduces the flash point, but the flammability of ternary blends is classified as Class II; similar to that of diesel. Cetane number is reduced in ternary blends by ethanol. So, palm biodiesel with minute percentage of anhydrous ethanol as additive in the ternary blend significantly improved key fuel properties significantly.

Md. Jayed Hussan; Masjuki Hj. Hassan; Md. Abul Kalam; Liaquat Ali Memon

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Gasoline and Diesel Fuel Update  

Gasoline and Diesel Fuel Update (EIA)

Price Data Collection Procedures Price Data Collection Procedures Every Monday, retail on-highway diesel prices are collected by telephone and fax from a sample of approximately 350 retail diesel outlets, including truck stops and service stations. The data represent the price of ultra low sulfur diesel (ULSD) which contains less than 15 parts-per-million sulfur. The Environmental Protection Agency (EPA) requires that all on-highway diesel sold be ULSD by December 1, 2010 (September 1, 2006 in California). In January 2007, the weekly on-highway diesel price survey began collecting diesel prices for low sulfur diesel (LSD) which contains between 15 and 500 parts-per-million sulfur and ULSD separately. Prior to January 2007, EIA collected the price of on-highway fuel without distinguishing the sulfur

242

Retail Diesel Fuel Oil Prices  

Gasoline and Diesel Fuel Update (EIA)

Along with heating oil prices, the distillate supply squeeze has Along with heating oil prices, the distillate supply squeeze has severely impacted diesel fuel prices, especially in the Northeast. Diesel fuel is bascially the same product as home heating oil. The primary difference is that diesel has a lower sulfur content. When heating oil is in short supply, low sulfur diesel fuel can be diverted to heating oil supply. Thus, diesel fuel prices rise with heating heating oil prices. Retail diesel fuel prices nationally, along with those of most other petroleum prices, increased steadily through most of 1999. But prices in the Northeast jumped dramatically in the third week of January. Diesel fuel prices in New England rose nearly 68 cents per gallon, or 47 percent, between January 17 and February 7. While EIA does not have

243

Influence of supporting materials on the deactivation of diesel exhaust catalysts  

Science Journals Connector (OSTI)

Two kinds of vehicle-aged diesel oxidation catalysts were analyzed. The phase transition of alumina as a support and Pt sintering after a long-time operation caused serious deactivation of the catalysts.

Song-Taek Oh; Sang-Min Kim; Man-Suk Yoon…

2007-04-01T23:59:59.000Z

244

Disk filter  

DOE Patents (OSTI)

An electric disk filter provides a high efficiency at high temperature. A hollow outer filter of fibrous stainless steel forms the ground electrode. A refractory filter material is placed between the outer electrode and the inner electrically isolated high voltage electrode. Air flows through the outer filter surfaces through the electrified refractory filter media and between the high voltage electrodes and is removed from a space in the high voltage electrode.

Bergman, W.

1985-01-09T23:59:59.000Z

245

Ultra-Low Sulfur diesel Update & Future Light Duty Diesel | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ultra-Low Sulfur diesel Update & Future Light Duty Diesel Ultra-Low Sulfur diesel Update & Future Light Duty Diesel Presentation given at DEER 2006, August 20-24, 2006, Detroit,...

246

Practical implications of marine diesel engine emission regulations  

SciTech Connect

The main pollutants from marine diesel engines are oxides of nitrogen (NOx), sulfur oxides (SOx) and particulates (soot). However, the proposed marine diesel engine emission regulations will primarily focus on the levels of NOx and SOx. In the future, once the proposed regulations are met, the limits and levels of other emissions will come under increasing scrutiny, such as particulates, hydrocarbons and carbon monoxide. Regardless of the type of pollutant, there are generally two classes of emission control: (1) techniques that reduce the amount of pollutant formed in the combustion process, or (2) prevent the pollutants from reaching the atmosphere. Unfortunately, some of these control techniques will not be able to meet the incoming regulations. Therefore, this paper identifies the diesel engine emissions of concern, the impending regulations, and the merits of current and future emission control technologies required to meet these regulations.

Bowen, C.E.; Potter, I.J.; Reader, G.T. [Univ. of Calgary, Alberta (Canada). Dept. of Mechanical Engineering

1996-09-01T23:59:59.000Z

247

Performance and Emissions of Direct Injection Diesel Engine Fueled with Diesel Fuel Containing Dissolved Methane  

Science Journals Connector (OSTI)

State Key Laboratory of Multiphase Flow in Power Engineering, Xi'an Jiaotong University, Xi'an 710049, People's Republic of China ... soot and nitrogen oxides, from direct injection Diesel engines, engineers have proposed various solns., one of which is the use of a gaseous fuel as a partial supplement for liq. ... (16)?Heywood, J. B. Internal Combustion Engine Fundamentals; McGraw-Hill:? New York, 1988. ...

Junqiang Zhang; Deming Jiang; Zuohua Huang; Xibin Wang; Qi Wei

2006-01-19T23:59:59.000Z

248

DIESEL FUEL LUBRICATION  

SciTech Connect

The diesel fuel injector and pump systems contain many sliding interfaces that rely for lubrication upon the fuels. The combination of the poor fuel lubricity and extremely tight geometric clearance between the plunger and bore makes the diesel fuel injector vulnerable to scuffing damage that severely limits the engine life. In order to meet the upcoming stricter diesel emission regulations and higher engine efficiency requirements, further fuel refinements that will result in even lower fuel lubricity due to the removal of essential lubricating compounds, more stringent operation conditions, and tighter geometric clearances are needed. These are expected to increase the scuffing and wear vulnerability of the diesel fuel injection and pump systems. In this chapter, two approaches are discussed to address this issue: (1) increasing fuel lubricity by introducing effective lubricity additives or alternative fuels, such as biodiesel, and (2) improving the fuel injector scuffing-resistance by using advanced materials and/or surface engineering processes. The developing status of the fuel modification approach is reviewed to cover topics including fuel lubricity origins, lubricity improvers, alternative fuels, and standard fuel lubricity tests. The discussion of the materials approach is focused on the methodology development for detection of the onset of scuffing and evaluation of the material scuffing characteristics.

Qu, Jun [ORNL

2012-01-01T23:59:59.000Z

249

Diesel Engine Alternatives  

SciTech Connect

There are basically three different modes of combustion possible for use in reciprocating engines. These include, diffusion burning, as occurs in current diesel engines, flame propagation combustion such as used in conventional SI engines, and homogeneous combustion such as is used in the SwRI HCCI engine. Diesel engines currently offer significant fuel consumption benefits relative to other powerplants for on and off road applications; however, costs and efficiency may become problems as the emissions standards become even more stringent. This presentation presents a discussion of the potentials of HCCI and flame propagation engines as alternatives to the diesel engines. It is suggested that as the emissions standards become more and more stringent, the advantages of the diesel may disappear. The potential for HCCI is limited by the availability of the appropriate fuel. The potential of flame propagation engines is limited by several factors including knock, EGR tolerance, high BMEP operation, and throttling. These limitations are discussed in the context of potential for improvement of the efficiency of the flame propagation engine.

Ryan, T

2003-08-24T23:59:59.000Z

250

Definition: Diesel fuel | Open Energy Information  

Open Energy Info (EERE)

Diesel fuel Diesel fuel Jump to: navigation, search Dictionary.png Diesel fuel A liquid fuel produced from petroleum; used in diesel engines.[1] View on Wikipedia Wikipedia Definition Diesel oil and Gazole (fuel) redirect here. Sometimes "diesel oil" is used to mean lubricating oil for diesel engines. Diesel fuel in general is any liquid fuel used in diesel engines. The most common is a specific fractional distillate of petroleum fuel oil, but alternatives that are not derived from petroleum, such as biodiesel, biomass to liquid (BTL) or gas to liquid (GTL) diesel, are increasingly being developed and adopted. To distinguish these types, petroleum-derived diesel is increasingly called petrodiesel. Ultra-low-sulfur diesel (ULSD) is a standard for defining diesel fuel with substantially lowered sulfur contents. As of 2007, almost

251

The John Deere E diesel Test & Research Project  

SciTech Connect

Three non-road Tier II emissions compliant diesel engines manufactured by John Deere were placed on a durability test plan of 2000 hours each at full load, rated speed (FLRS). The fuel was a blend of 10% fuel ethanol and 90% low sulfur #2 diesel fuel. Seven operational failures involving twenty seven fuel system components occurred prior to completion of the intended test plan. Regulated emissions measured prior to component failure indicated compliance to Tier II certification goals for the observed test experience. The program plan included operating three non-road Tier II diesel engines for 2000 hours each monitoring the regulated emissions at 500 hour intervals for changes/deterioration. The program was stopped prematurely due to number and frequency of injection system failures. The failures and weaknesses observed involved injector seat and valve wear, control solenoid material incompatibility, injector valve deposits and injector high pressure seal cavitation erosion. Future work should target an E diesel fuel standard that emphasizes minimum water content, stability, lubricity, cetane neutrality and oxidation resistance. Standards for fuel ethanol need to require water content no greater than the base diesel fuel standard. Lubricity bench test standards may need new development for E diesel.

Fields, Nathan; Mitchell, William E.

2008-09-23T23:59:59.000Z

252

Characteristics of the performance and emissions of a HSDI diesel engine running with cottonseed oil or its methyl ester and their blends with diesel fuel  

Science Journals Connector (OSTI)

An experimental study has been conducted to evaluate the use of various blends of cottonseed oil or its methyl ester (bio-diesel) with diesel fuel, in blend ratios from 10/90 up to 100/0, in a fully instrumented, four-stroke, High Speed Direct Injection (HSDI), Ricardo/Cussons 'Hydra' diesel engine. The tests were conducted using each of the above fuel blends or neat fuels, with the engine working at a medium and a high load. Volumetric fuel consumption, exhaust smokiness and exhaust-regulated gas emissions such as nitrogen oxides, carbon monoxide and unburnt hydrocarbons were measured. The differences in the performance and exhaust emissions from the baseline operation of the engine, that is, when working with neat diesel fuel, were determined and compared, as well as the differences between cottonseed oil or its methyl ester and their blends. Theoretical aspects of diesel engine combustion were used to aid the correct interpretation of the engine behaviour.

Constantine D. Rakopoulos; Kimon A. Antonopoulos; Dimitrios C. Rakopoulos; Emmanuel C. Kakaras; Efthimios G. Pariotis

2007-01-01T23:59:59.000Z

253

Diesel Emission Control Review  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Review Tim Johnson August 10, 2005 Full version for website Presentaton will be condensed 2 * Filters are making significant progress with sophisticated regeneration schemes and...

254

E-Print Network 3.0 - air intake filter Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

results for: air intake filter Page: << < 1 2 3 4 5 > >> 1 Fault Tolerant Oxygen Control of a Diesel Engine Air System Summary: which is the oxygen concentration in the...

255

Combustion and emission characteristics of a turbocharged diesel engine using high premixed ratio of methanol and diesel fuel  

Science Journals Connector (OSTI)

Abstract The combustion and emission characteristics of a dual fuel diesel engine with high premixed ratio of methanol (PRm) were investigated. Experiments were performed on a 6-cylinder turbocharged, inter-cooling diesel engine. Methanol was injected through the intake port and ignited by direct injected diesel in the cylinder, the maximum \\{PRm\\} was over 70%. The experimental results showed that with high PRm, the maximum in-cylinder pressure increased from medium to high engine load but varied little or even decreased at low engine speed and load. High \\{PRm\\} prolonged the ignition delay but shortened the combustion duration and decreased the in-cylinder gas temperature at ignition timing. Hydrocarbons (HC), carbon monoxide (CO), formaldehyde emissions and the proportion of nitrogen dioxide (NO2) in nitrogen oxides (NOX) increased significantly with the increase of \\{PRm\\} while NOX and dry soot emissions were significantly reduced, which meant the trade-off relationship between NOX and soot emissions disappeared. The increased HC, CO and formaldehyde emissions could be effectively reduced by diesel oxidation catalyst (DOC) when the exhaust gas temperature reached the light off temperature of the DOC. After DOC, the NO2 proportion in NOX was greatly reduced to less than that of baseline engine at methanol premixed mode but increased slightly at pure diesel mode. The maximum \\{PRm\\} was confined by in-cylinder pressure at high engine speed and load. But at low engine speed and load, it was confined by the high emissions of HC, CO and formaldehyde even after DOC.

Lijiang Wei; Chunde Yao; Quangang Wang; Wang Pan; Guopeng Han

2015-01-01T23:59:59.000Z

256

Gasoline and Diesel Fuel Update  

Gasoline and Diesel Fuel Update (EIA)

Methodology For Gasoline and Diesel Fuel Pump Components Methodology For Gasoline and Diesel Fuel Pump Components The components for the gasoline and diesel fuel pumps are calculated in the following manner in cents per gallon and then converted into a percentage: Crude Oil - the monthly average of the composite refiner acquisition cost, which is the average price of crude oil purchased by refiners. Refining Costs & Profits - the difference between the monthly average of the spot price of gasoline or diesel fuel (used as a proxy for the value of gasoline or diesel fuel as it exits the refinery) and the average price of crude oil purchased by refiners (the crude oil component). Distribution & Marketing Costs & Profits - the difference between the average retail price of gasoline or diesel fuel as computed from EIA's

257

Diesel fuel qualities  

SciTech Connect

As a result of rising fuel costs, many ship operators are turning to less expensive, heavier grade fuels for their diesel engines. Use of these lower quality fuels without adequate preparation can cause increased engine wear and damage to fuel systems. The oil properties which affect pretreatment and cleaning requirements, specifications that should be used when purchasing these fuels, and procedures for confirming that bought fuels meet purchase specifications are discussed. (LCL)

Blenkey, N.

1981-02-01T23:59:59.000Z

258

Anti-air pollution & energy conservation system for automobiles using leaded or unleaded gasoline, diesel or alternate fuel  

DOE Patents (OSTI)

Exhaust gases from an internal combustion engine operating with leaded or unleaded gasoline or diesel or natural gas, are used for energizing a high-speed gas turbine. The convoluting gas discharge causes a first separation stage by stratifying of heavier and lighter exhaust gas components that exit from the turbine in opposite directions, the heavier components having a second stratifying separation in a vortex tube to separate combustible pollutants from non-combustible components. The non-combustible components exit a vortex tube open end to atmosphere. The lighter combustible, pollutants effected in the first separation are bubbled through a sodium hydroxide solution for dissolving the nitric oxide, formaldehyde impurities in this gas stream before being piped to the engine air intake for re-combustion, thereby reducing the engine's exhaust pollution and improving its fuel economy. The combustible, heavier pollutants from the second separation stage are piped to air filter assemblies. This gas stream convoluting at a high-speed through the top stator-vanes of the air filters, centrifugally separates the coalescent water, aldehydes, nitrogen dioxides, sulfates, sulfur, lead particles which collect at the bottom of the bowl, wherein it is periodically released to the roadway. Whereas, the heavier hydrocarbon, carbon particles are piped through the air filter's porous element to the engine air intake for re-combustion, further reducing the engine's exhaust pollution and improving its fuel economy.

Bose, Ranendra K. (14346 Jacob La., Centreville, VA 20120-3305)

2002-06-04T23:59:59.000Z

259

diesel | OpenEI  

Open Energy Info (EERE)

diesel diesel Dataset Summary Description The JodiOil World Database is freely available from the Joint Organisations Data Initiative (JODI) and is updated on or around the 20th of each month. Source JODI Date Released October 01st, 2004 (10 years ago) Date Updated March 21st, 2011 (3 years ago) Keywords crude oil diesel fuel oil gasoline kerosene LPG Data application/zip icon Text file, all JODI Database data: Jan 2002 - Jan 2011 (zip, 14.5 MiB) application/pdf icon Definitions of Abbreviations and Codes (pdf, 698.3 KiB) application/pdf icon Column Headings for Dataset (pdf, 13.4 KiB) Quality Metrics Level of Review Some Review Comment Some of the data has "some review" and some of the data has "no review"; the supplemental documentation provides definitions for the assessment codes for each piece of data in the datasets (essentially, 1 = some review, 2 = use with caution, 3 = not reviewed)

260

Diesel de Azufre Ultra Bajo  

NLE Websites -- All DOE Office Websites (Extended Search)

Diesel de Azufre Ultra Bajo Diesel de Azufre Ultra Bajo ULSD LSD Off-Road Diesel para Carretera de Azufre Ultra Bajo (máximo de 15 ppm de azufre). Se requiere su uso en todos los motores y vehículos diesel de carretera modelos 2007 y posteriores. También se recomienda su uso en todos los vehículos y motores diesel. Diesel para Carretera Bajo en Azufre (máximo de 500 ppm de azufre). Aviso: La ley federal prohíbe su uso en vehículos y motores modelos 2007 y posteriores, su uso podría dañarlos. Combustible Diesel que no es para Carretera (puede exceder 500 ppm de azufre). Aviso: La ley federal prohíbe su uso en vehículos y motores que no son de carretera, su uso podría dañarlos. Los consumidores con vehículos modelo 2007 ó posteriores deben utilizar solo diesel ultra bajo de azufre (ULSD). El ULSD es un diesel de

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Sandia National Laboratories: Diesel Combustion  

NLE Websites -- All DOE Office Websites (Extended Search)

Diesel Combustion Caterpillar, Sandia CRADA Opens Door to Multiple Research Projects On April 17, 2013, in Capabilities, Computational Modeling & Simulation, CRF, Materials...

262

Utiization of alternate fuels in diesel engines  

SciTech Connect

Accomplishments during three years entitled The Utilization of Alternate Fuels in Diesel Engines are summarized. Experiments were designed and test equipment set-up for the purpose of evaluating the use of methanol as a fumigant for light-duty Diesel engine service. The major experimental results were obtained from a multicylinder automotive Diesel engine. However, fundamental studies employing a GC/micro-reactor and a constant volume combustion bomb were also started. The purpose of this work was to measure some of the chemical and physical properties of methanol and methanol-air mixtures. The laminar flame velocity for various mixtures has been measured in the combustion bomb and thermal degradation studies have begun in the GC/micro-reactor. An Oldsmobile 5.7 liter V/8 Diesel engine was fumigated with methanol in amounts up to 40% of the fuel energy. The primary objectives of the study were to determine the effect of methanol fumigation on fuel efficiency, smoke, nitric oxide emission, and the occurrence of severe knock. An assessment of the biological activity for samples of the raw exhaust particulate and its soluble organic extract was also made using boh the Ames Salmonella typhimurium test and the B. subtilis Comptest. Generally, methanol fumigation was found to decrease NO emission for all conditions, to have a slight effect on smoke opacity, and to have a beneficial effect on fuel efficiency at higher loads. Also at higher loads, the methanol was found to induce what was defined as knock limited operation. The biological activity of the raw particulate matter was fond to be less than that of its soluble organic extract. However, for both the fumigation of methanol did enhance the biological activity.

Lestz, S.S.

1980-09-01T23:59:59.000Z

263

Toxic components in diesel exhaust fumes  

Science Journals Connector (OSTI)

To control diesel-engine toxicity, a computation method is proposed for the concentration of toxic components in diesel exhaust fumes, on the basis of external engine...

A. F. Dorokhov; E. V. Klimova

2009-12-01T23:59:59.000Z

264

Electrochemical NOx Sensor for Monitoring Diesel Emissions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

fuel economy - Completely compatible with biodiesel Estimate diesel light-vehicle penetration to increase from 3% (2007) to 14% by 2017 * Problem: Diesel technology is...

265

Optimization of Advanced Diesel Engine Combustion Strategies...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Optimization of Advanced Diesel Engine Combustion Strategies Optimization of Advanced Diesel Engine Combustion Strategies 2010 DOE Vehicle Technologies and Hydrogen Programs Annual...

266

Diesel vs Gasoline Production | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

vs Gasoline Production Diesel vs Gasoline Production A look at refinery decisions that decide "swing" between diesel and gasoline production deer08leister.pdf More Documents &...

267

Influence of different configurations of a catalyst and a trap on particulate emission of a diesel passenger car  

Science Journals Connector (OSTI)

New particulate emission measurements performed on a diesel passenger car to see the influence of different configurations of after-treatment systems are reported. Five combinations of a particle trap and an oxidation catalyst are investigated. These configurations are discussed in view of particulate emission, measured by number and mass. All measurements were carried out at a chassis dynamometer of the EMPA. A diesel passenger car with an IDI engine was operated at four steady state conditions. Exhaust gas was diluted in a standard constant volume sampler (CVS) device (full flow dilution tunnel). Particulate size distributions were measured with a scanning mobility particle sizer (SMPS) and gravimetric measurements were performed according to regulations. Furthermore, measurements without CVS tunnel were done by using external dilution units to see the influence of the sampling method. We used a thermo desorber to distinguish volatile and non-volatile aerosol fractions and we analysed filter samples for determination of organic soluble fraction, water-soluble fraction and sulphur content. Huge differences depending on the configuration of the after-treatment system and load were observed. In general it was found that a large reduction of particulate emission could be obtained by using a particle trap. A catalyst converter has minor effect on particulate emission. Nucleation of new particles was observed under certain conditions depending on configuration and sampling method.

Urs Lehmann; Martin Mohr

2001-01-01T23:59:59.000Z

268

2D Axisymmetric Coupled CFD-kinetics Modeling of a Nonthermal Arc Plasma Torch for Diesel Fuel  

E-Print Network (OSTI)

-assisted diesel fuel reformer developed for two different applications: (i) onboard H2 production for fuel cell been also developed for different reforming reactors: solid oxide fuel cell (SOFC)7 , membrane reformer1 2D Axisymmetric Coupled CFD-kinetics Modeling of a Nonthermal Arc Plasma Torch for Diesel Fuel

Boyer, Edmond

269

Evaluation of Fuel Cell Auxiliary Power Units for Heavy-Duty Diesel Trucks  

E-Print Network (OSTI)

diesel fuel consumption, lubricant changes, and enginefuel consumption, and costs associated with diesel engineDiesel Idling diesel consumption Diesel fuel cost Lubricant cost Engine

2002-01-01T23:59:59.000Z

270

Exhaust emissions characteristics of a multi-cylinder 18.1-L diesel engine converted to fueled with natural gas and diesel pilot  

Science Journals Connector (OSTI)

Abstract A six-cylinder, turbocharged and aftercooled diesel engine was converted to operate with natural gas and diesel pilot for generator application. The flow of natural gas was electronically controlled using a throttle valve, and it was pre-mixed with air before being introduced into the combustion chambers. The aim of this work was to study the exhaust emissions characteristics under diesel and dual fuel operations at different operating conditions. Exhaust emissions of total hydrocarbons (HC), carbon monoxide (CO), nitrogen oxides (NOx), soot, particulate matter and carbon dioxide were measured at different loads. This work also presents the effects of diesel oxidation catalyst on HC and CO conversions under dual fuel operation. Results showed that \\{NOx\\} emission was reduced at all operating loads under dual fuel operation compared to diesel operation. HC and CO emissions were increased under dual fuel operation, but their concentrations were considerably reduced with oxidation catalyst. Contrary to conventional wisdom, it was found that soot and particulate matter were increased under dual fuel operation compared to diesel operation.

Mayank Mittal; Ron Donahue; Peter Winnie; Allen Gillette

2014-01-01T23:59:59.000Z

271

Reformulated diesel fuel and method  

DOE Patents (OSTI)

A method for mathematically identifying at least one diesel fuel suitable for combustion in an automotive diesel engine with significantly reduced emissions and producible from known petroleum blendstocks using known refining processes, including the use of cetane additives (ignition improvers) and oxygenated compounds.

McAdams, Hiramie T [Carrollton, IL; Crawford, Robert W [Tucson, AZ; Hadder, Gerald R [Oak Ridge, TN; McNutt, Barry D [Arlington, VA

2006-08-22T23:59:59.000Z

272

Diesel prices continue to rise  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices continue to rise The U.S. average retail price for on-highway diesel fuel rose to 4.16 a gallon on Monday. That's up 5.3 cents from a week ago, based on the weekly...

273

Diesel prices up this week  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices up this week The U.S. average retail price for on-highway diesel fuel rose sharply to 4.10 a gallon on Monday. That's up 8.2 cents from a week ago and 17.7 cents...

274

Size-Resolved Density Measurements of Particulate Emissions from an Advanced Combustion Diesel Engine: Effect of Aggregate Morphology  

SciTech Connect

We report the first in situ size-resolved density measurements of particles produced by premixed charge compression ignition (PCCI) and compare these with conventional diesel particles. The densities of size-classified particles were determined by measurements with a differential mobility analyzer (DMA) and an aerosol particle mass analyzer (APM). Particle masses of the different size classes were evaluated with a proposed DMA-APM response function for aggregates. Our results indicate that the effective densities of PCCI and conventional diesel particles were approximately the same for 50 and 100 nm electrical mobility diameters (0.9 and 0.6 g/cc, respectively), but the PCCI particle effective density (0.4 g/cc) was less than the conventional (0.5 g/cc) for 150 nm. The lowest effective particle densities were observed for exhaust gas recirculation (EGR) levels somewhat less than that required for PCCI operation. The inherent densities of conventional particles in the 50 and 100 nm size classes were 1.22 and 1.77 g/cc, which is in good agreement with Park et al. (2004). PCCI inherent particle densities for these same size classes were higher (1.27 and 2.10 g/cc), suggesting that there may have been additional adsorbed liquid hydrocarbons. For 150 nm particles, the inherent densities were nearly the same for PCCI and conventional particles at 2.20 g/cc. We expect that the lower effective density of PCCI particles may improve particulate emissions control with diesel particulate filters (DPFs). The presence of liquid hydrocarbons may also promote oxidation in DPFs.

Barone, Teresa L [ORNL; Storey, John Morse [ORNL; Prikhodko, Vitaly Y [ORNL; Parks, II, James E [ORNL

2011-01-01T23:59:59.000Z

275

Gasoline and Diesel Fuel Update  

Gasoline and Diesel Fuel Update (EIA)

Procedures, Methodology, and Coefficients of Variation Procedures, Methodology, and Coefficients of Variation Diesel Fuel Price Data Collection Procedures Every Monday, cash self-serve on-highway diesel prices (including taxes) are collected from a sample of approximately 400 retail diesel outlets in the continental U.S. The sample includes a combination of truck stops and service stations that sell on-highway diesel fuel. The data represent the price of ultra low sulfur diesel (ULSD) which contains less than 15 parts-per-million sulfur. The prices are collected via telephone, fax, email, or the internet from participating outlets. All collected prices are subjected to automated edit checks during data collection and data processing. Data flagged by the edits are verified with the respondents. Imputation is used for companies

276

Retail Diesel Fuel Oil Prices  

Gasoline and Diesel Fuel Update (EIA)

Along with heating oil prices, the distillate supply squeeze has Along with heating oil prices, the distillate supply squeeze has severely impacted diesel fuel prices, especially in the Northeast. Retail diesel price data are available sooner than residential heating oil data. This graph shows that diesel prices turned the corner sometime after February 7 and are heading down. Retail diesel fuel prices nationally, along with those of most other petroleum prices, increased steadily through most of 1999. Prices jumped dramatically (by over 11 cents per gallon) in the third week of January, and rose 2 or more cents a week through February 7. The increases were much more rapid in the Northeast. From January 17 through February 7, diesel fuel prices in New England rose nearly 68 cents per gallon, or 47 percent. Prices in the Mid-Atlantic region rose about 58

277

Federal Tax Credit for Diesels  

NLE Websites -- All DOE Office Websites (Extended Search)

Diesels Diesels Diesel Vehicle Federal tax credit up to $3,400! Some diesels purchased or placed into service after December 31, 2005 may be eligible for a federal income tax credit of up to $3,400. (No eligible vehicles were manufactured for sale until 2008.) Credit amounts begin to phase out for a given manufacturer once it has sold over 60,000 eligible hybrid and diesel vehicles. Vehicles purchased after December 31, 2010 are not eligible for this credit. The information below is provided for those filing amended tax returns for previous years. Audi BMW Mercedes-Benz Volkswagen All Vehicle Make & Model Full Credit Phase Out No Credit 50% 25% Audi Jan. 1, 2006 July 1 - Dec. 31, 2010 Not Applicable Jan. 1, 2011 Audi A3 TDI 2010-11 Audi A3 2.0L TDI $1,300 $650 -- $0

278

"Performance, Emission and Particle distribution of Diesel Engines Fueled with Diesel-Dimethoxymethane (DMM) Blends"  

E-Print Network (OSTI)

Xibin Wang "Performance, Emission and Particle distribution of Diesel Engines Fueled with Diesel-Dimethoxymethane (DMM) Blends" Abstract : Combustion, performance and emission were studied for DI diesel engine fuelled with DMM/diesel fuel blends for DMM content from 0 to 50%. Results showed that, for diesel engine with fuel

279

Filtering apparatus  

DOE Patents (OSTI)

A vertical vessel having a lower inlet and an upper outlet enclosure separated by a main horizontal tube sheet. The inlet enclosure receives the flue gas from a boiler of a power system and the outlet enclosure supplies cleaned gas to the turbines. The inlet enclosure contains a plurality of particulate-removing clusters, each having a plurality of filter units. Each filter unit includes a filter clean-gas chamber defined by a plate and a perforated auxiliary tube sheet with filter tubes suspended from each tube sheet and a tube connected to each chamber for passing cleaned gas to the outlet enclosure. The clusters are suspended from the main tube sheet with their filter units extending vertically and the filter tubes passing through the tube sheet and opening in the outlet enclosure. The flue gas is circulated about the outside surfaces of the filter tubes and the particulate is absorbed in the pores of the filter tubes. Pulses to clean the filter tubes are passed through their inner holes through tubes free of bends which are aligned with the tubes that pass the clean gas.

Haldipur, Gaurang B. (Monroeville, PA); Dilmore, William J. (Murrysville, PA)

1992-01-01T23:59:59.000Z

280

Heavy Duty Diesels- The Road Ahead  

Energy.gov (U.S. Department of Energy (DOE))

This presentation gives a landscape picture of diesel engine technologies from the Daimler point of view.

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Drive cycle analysis of butanol/diesel blends in a light-duty vehicle.  

SciTech Connect

The potential exists to displace a portion of the petroleum diesel demand with butanol and positively impact engine-out particulate matter. As a preliminary investigation, 20% and 40% by volume blends of butanol with ultra low sulfur diesel fuel were operated in a 1999 Mercedes Benz C220 turbo diesel vehicle (Euro III compliant). Cold and hot start urban as well as highway drive cycle tests were performed for the two blends of butanol and compared to diesel fuel. In addition, 35 MPH and 55 MPH steady-state tests were conducted under varying road loads for the two fuel blends. Exhaust gas emissions, fuel consumption, and intake and exhaust temperatures were acquired for each test condition. Filter smoke numbers were also acquired during the steady-state tests.

Miers, S. A.; Carlson, R. W.; McConnell, S. S.; Ng, H. K.; Wallner, T.; LeFeber, J.; Energy Systems; Esper Images Video & Multimedia

2008-10-01T23:59:59.000Z

282

Alternative Fuels Data Center: Diesel Vehicle Availability  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Diesel Vehicle Diesel Vehicle Availability to someone by E-mail Share Alternative Fuels Data Center: Diesel Vehicle Availability on Facebook Tweet about Alternative Fuels Data Center: Diesel Vehicle Availability on Twitter Bookmark Alternative Fuels Data Center: Diesel Vehicle Availability on Google Bookmark Alternative Fuels Data Center: Diesel Vehicle Availability on Delicious Rank Alternative Fuels Data Center: Diesel Vehicle Availability on Digg Find More places to share Alternative Fuels Data Center: Diesel Vehicle Availability on AddThis.com... More in this section... Biodiesel Basics Benefits & Considerations Stations Vehicles Availability Emissions Laws & Incentives Diesel Vehicle Availability According to J.D. Power Automotive Forecasting, demand for light-duty diesel vehicles might double in the next 10 years. More auto manufacturers

283

Advanced Petroleum-Based Fuels -- Diesel Emissions Control Project (APBF-DEC): Lubricants Project, Phase 2 Final Report  

SciTech Connect

This report summarizes the results of the second phase of a lubricants project, which investigated the impact of engine oil formulation on diesel vehicle emissions and the performance of a nitrogen oxide adsorber catalyst (NAC).

Not Available

2006-06-01T23:59:59.000Z

284

Emissions and fuel economy of a prechamber diesel engine with natural gas dual fuelling  

SciTech Connect

A four-cylinder turbocharged prechamber diesel engine (Caterpillar 3304) was operated with natural gas and pilot diesel fuel ignition over a wide range of load and speed. Measurements were made of fuel consumption and the emissions of unburned hydrocarbons, carbon monoxide, and the oxides of nitrogen. Improvements in fuel economy and emissions were found to be affected by the diesel fuel-gas fraction, and by air restriction and fuel injection timing. Boundaries of unstable, inefficient and knocking operation were defined and the importance of gas-air equivalance ratio was demonstrated in its effect on economy, emissions and stability of operation.

Ding, X.; Hill, P.G.

1986-01-01T23:59:59.000Z

285

North American Market Challenges for Diesel Engines | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

North American Market Challenges for Diesel Engines North American Market Challenges for Diesel Engines 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: Gale...

286

Future Breathing System Requirements for Clean Diesel Engines...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Breathing System Requirements for Clean Diesel Engines Future Breathing System Requirements for Clean Diesel Engines Poster presentation at the 2007 Diesel Engine-Efficiency &...

287

Achieving High-Effiency Clean Ccombustion in Diesel Engines ...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Achieving High-Effiency Clean Ccombustion in Diesel Engines Achieving High-Effiency Clean Ccombustion in Diesel Engines 2004 Diesel Engine Emissions Reduction (DEER) Conference...

288

Technical Challenges and Opportunities Light-Duty Diesel Engines...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Challenges and Opportunities Light-Duty Diesel Engines in North America Technical Challenges and Opportunities Light-Duty Diesel Engines in North America 2005 Diesel Engine...

289

SCR & DPF RETROFITS FOR MOBILE DIESEL ENGINES | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SCR & DPF RETROFITS FOR MOBILE DIESEL ENGINES SCR & DPF RETROFITS FOR MOBILE DIESEL ENGINES 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters...

290

Engine Materials for Clean Diesel Technology: An Overview | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Materials for Clean Diesel Technology: An Overview Engine Materials for Clean Diesel Technology: An Overview Presentation given at the 2007 Diesel Engine-Efficiency & Emissions...

291

Update on 2007 Diesel Particulate Measurement Research | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

2007 Diesel Particulate Measurement Research Update on 2007 Diesel Particulate Measurement Research 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and...

292

An Improvement of Diesel PM and NOx Reduction System | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

& Publications Development on simultaneous reduction system of NOx and PM from a diesel engine An Improvement of Diesel PM and NOx Reduction System New Diesel Emissions...

293

Cummins Light Truck Clean Diesel | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Light Truck Clean Diesel Cummins Light Truck Clean Diesel 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation 2004deerstang2.pdf More Documents & Publications...

294

Synthesis and Evaluation of Wax Dispersant for Diesel  

Science Journals Connector (OSTI)

Synthesis and Evaluation of Wax Dispersant for Diesel ... We can predict that the sensitivity of diesels A and C will be better than that of diesel B. ...

Wangang Zheng; Shujun Wang; Jie Liu; Fanbin Meng; Yanshan Li; Huanqing Ma; Ting Li

2014-02-28T23:59:59.000Z

295

The State of the Science in Diesel Particulate Control | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

The State of the Science in Diesel Particulate Control The State of the Science in Diesel Particulate Control 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations...

296

Regulated Emissions from Diesel and Compressed Natural Gas Transit...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Emissions from Diesel and Compressed Natural Gas Transit Buses Regulated Emissions from Diesel and Compressed Natural Gas Transit Buses Poster presentaiton at the 2007 Diesel...

297

Lubricant Formulation and Consumption Effects on Diesel Exhaust...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Lubricant Formulation and Consumption Effects on Diesel Exhaust Ash Emissions: Lubricant Formulation and Consumption Effects on Diesel Exhaust Ash Emissions: 2005 Diesel Engine...

298

Impact of Clean Diesel Technology on Climate Change | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Clean Diesel Technology on Climate Change Impact of Clean Diesel Technology on Climate Change 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: Brookhaven...

299

Alloy Foam Diesel Emissions Control School Bus Implementation...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Alloy Foam Diesel Emissions Control School Bus Implementation Alloy Foam Diesel Emissions Control School Bus Implementation Poster presentation from the 2007 Diesel...

300

How Exhaust Emissions Drive Diesel Engine Fuel Efficiency | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

How Exhaust Emissions Drive Diesel Engine Fuel Efficiency How Exhaust Emissions Drive Diesel Engine Fuel Efficiency 2004 Diesel Engine Emissions Reduction (DEER) Conference...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Perspectives Regarding Diesel Engine Emissions Reduction in the...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Perspectives Regarding Diesel Engine Emissions Reduction in the Northeast Perspectives Regarding Diesel Engine Emissions Reduction in the Northeast 2004 Diesel Engine Emissions...

302

Verification of Shell GTL Fuel as CARB Alternative Diesel | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Verification of Shell GTL Fuel as CARB Alternative Diesel Verification of Shell GTL Fuel as CARB Alternative Diesel Presentation given at the 2007 Diesel Engine-Efficiency &...

303

Hydrogen as a Supplemental Fuel in Diesel Engines | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

as a Supplemental Fuel in Diesel Engines Hydrogen as a Supplemental Fuel in Diesel Engines Poster presentation from the 2007 Diesel Engine-Efficiency & Emissions Research...

304

Electrochemical NOxSensor for Monitoring Diesel Emissions | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Diesel Emissions Electrochemical NOxSensor for Monitoring Diesel Emissions pm02glass.pdf More Documents & Publications Electrochemical NOx Sensor for Monitoring Diesel...

305

DOE's Gasoline/Diesel PM Split Study | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

GasolineDiesel PM Split Study DOE's GasolineDiesel PM Split Study 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005deerfujita.pdf More...

306

Business Case for Light-Duty Diesels | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Business Case for Light-Duty Diesels Business Case for Light-Duty Diesels 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005deergodwin.pdf...

307

New Catalysts for Green Diesel | The Ames Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

New Catalysts for Green Diesel A new economical and efficient catalyst for upgrading renewable feedstocks to green diesel has been created. Green diesel, produced by converting...

308

Next Generation Diesel Engine Control | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Diesel Engine Control Next Generation Diesel Engine Control Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007,...

309

NOx Emissions of Alternative Diesel Fuels:? A Comparative Analysis of Biodiesel and FT Diesel  

Science Journals Connector (OSTI)

This study explores the diesel injection and combustion processes in an effort to better understand the differences in NOx emissions between biodiesel, Fischer?Tropsch (FT) diesel, and their blends with a conventional diesel fuel. Emissions studies were ...

James P. Szybist; Stephen R. Kirby; André L. Boehman

2005-05-14T23:59:59.000Z

310

Novel Water-Neutral Diesel Fuel Processor and Sulfur Trap„Precision Combustion  

NLE Websites -- All DOE Office Websites (Extended Search)

Novel Water-Neutral Diesel Fuel Novel Water-Neutral Diesel Fuel Processor and Sulfur Trap-Precision Combustion Background Solid-Oxide Fuel Cell (SOFC) technology for auxiliary power units (APUs) offers the potential for major contributions toward Department of Energy (DOE) objectives such as clean energy deployment and improved efficiency. Reforming of conventional liquid fuels to produce synthesis gas (syngas) fuel for SOFC stacks is a practical approach for operating fuel cell APUs

311

Effect of n-Heptane Premixing on Combustion Characteristics of Diesel Engine  

Science Journals Connector (OSTI)

Effect of n-Heptane Premixing on Combustion Characteristics of Diesel Engine ... Department of Mechanical Engineering, Hanyang University, 17 Haengdang-dong, Sungdong-gu, Seoul 133-791, Korea ... In a different analysis, Simescu et al.17 explained, using their diesel-fueled partial HCCI engines, that soot formed during the premixed combustion period before DI fuel injection is not oxidized completely and emitted as exhaust gas. ...

Dae Sik Kim; Chang Sik Lee

2005-09-23T23:59:59.000Z

312

AIR POLLUTION: Diesel Fuel Culprits  

Science Journals Connector (OSTI)

AIR POLLUTION: Diesel Fuel Culprits ... Low-molecular-weight components aren't necessarily the true culprits of diesel fuel pollution, although they do contribute to it, according to Hertha Skala, assistant director of research, and her coworkers F. G. Padrta and P. C. Samson at Universal Oil Products. ... At the first national symposium on heterogeneous catalysis for control of air pollution, sponsored by Philadelphia's Franklin Institute, Mrs. Skala identified five different classes of oxygenated hydrocarbons found over the full molecular-weight range of diesel fuel components. ...

1968-12-02T23:59:59.000Z

313

Effects of diesel-water emulsion combustion on diesel engine NOx emissions. Final report, 1 January 1998--1 May 1999  

SciTech Connect

This study examines the effects of combusting a mixture of diesel fuel, water, and surfactant on the nitrogen oxides (NOx) emissions from a compression ignition diesel engine. Extensive previous research in the literature has attributed the observed reduction of nitrogen oxide emissions to a suppression of flame temperature due to quenching effects from the water, thereby reducing thermal NOx formation. The report highlights the relevant theory, operation, and design parameters of diesel internal combustion engines. Experimental procedures conducted using a Detroit Diesel 4-cylinder diesel engine are discussed. Results from testing diesel fuel with varying ratios of water balanced with a surfactant to stabilize the emulsion are presented and discussed. The data shows significant NOx emission reduction with up to 45 percent water, by volume, in the fuel. These results are correlated with thermodynamic first law and equilibrium combustion products analyses to estimate the adiabatic flame temperature of the standard fuel and fuel-water emulsion cases. Results indicate that thermal NOx is indeed reduced by quenching and flame temperature suppression, confirming reports in the literature. Recommendations are given for further studies, including improving the fuel-water emulsion and considerations for long-term testing.

Canfield, A.C.

1999-05-01T23:59:59.000Z

314

Reactivity Controlled Compression Ignition (RCCI) Combustion on a Multi-Cylinder Light-Duty Diesel Engine  

SciTech Connect

Reactivity controlled compression ignition is a low-temperature combustion technique that has been shown, both in computational fluid dynamics modeling and single-cylinder experiments, to obtain diesel-like efficiency or better with ultra-low nitrogen oxide and soot emissions, while operating primarily on gasoline-like fuels. This paper investigates reactivity controlled compression ignition operation on a four-cylinder light-duty diesel engine with production-viable hardware using conventional gasoline and diesel fuel. Experimental results are presented over a wide speed and load range using a systematic approach for achieving successful steady-state reactivity controlled compression ignition combustion. The results demonstrated diesel-like efficiency or better over the operating range explored with low engine-out nitrogen oxide and soot emissions. A peak brake thermal efficiency of 39.0% was demonstrated for 2600 r/min and 6.9 bar brake mean effective pressure with nitrogen oxide emissions reduced by an order of magnitude compared to conventional diesel combustion operation. Reactivity controlled compression ignition emissions and efficiency results are compared to conventional diesel combustion operation on the same engine.

Curran, Scott [ORNL; Hanson, Reed M [ORNL; Wagner, Robert M [ORNL

2012-01-01T23:59:59.000Z

315

Gasoline and Diesel Fuel Update  

Gasoline and Diesel Fuel Update (EIA)

Price Data Collection Procedures Price Data Collection Procedures Every Monday, cash self-serve on-highway diesel prices (including taxes) are collected from a sample of approximately 400 retail diesel outlets in the continental U.S. The sample includes a combination of truck stops and service stations that sell on-highway diesel fuel. The data represent the price of ultra low sulfur diesel (ULSD) which contains less than 15 parts-per-million sulfur. The prices are collected via telephone, fax, email, or the internet from participating outlets. All collected prices are subjected to automated edit checks during data collection and data processing. Data flagged by the edits are verified with the respondents. Imputation is used for companies that cannot be contacted and for reported prices that are extreme outliers.

316

Rudolf Diesel, 1858–1913  

Science Journals Connector (OSTI)

... that has in recent years seen spectacular changes) was the advent of the compression-ignition engine as a prime mover with its notable promoter, Rudolf ... as a prime mover with its notable promoter, Rudolf Diesel. ...

E. J. HOLMGREN

1958-03-15T23:59:59.000Z

317

Effect of different percentages of biodiesel–diesel blends on injection, spray, combustion, performance, and emission characteristics of a diesel engine  

Science Journals Connector (OSTI)

Abstract A comparative study of effect of different biodiesel–diesel blends (B5, B10, B15, B20, B25, B50 and B100) on injection, spray, combustion, performance, and emissions of a direct injection diesel engine at constant speed (1500 rpm) was carried out. The penetration distance increased with increase in percentage of biodiesel in diesel due to enhanced in-line fuel pressure. The simulation results indicate the spray penetration with biodiesel–diesel blend up to B15 does not lead to wall impingement but B20 is to be a critical limit of wall impingement (within uncertainty ±1.3%). However, it is observed clearly from the simulation results that probability of wall impingement is more with higher blends (B25, B50 and B100). The ignition delay period decreased with all biodiesel blends due to higher cetane number resulting in less rate of pressure rise and the smooth engine running operation. The engine torque does not change significantly with biodiesel–diesel blends up to 20% (B20). However, the torque reduction is about 2.7% with B100 at the rated load. Carbon monoxide (CO), hydrocarbon (HC) and smoke emissions decreased with all biodiesel–diesel blends. However, oxides of nitrogen (NOx) emission increased in the range of 1.4–22.8% with all biodiesel–diesel blends at rated load due to oxygenated fuel, automatic advance in dynamic injection timing (DIT), higher penetration and higher in-cylinder temperature. A notable conclusion emerged from this study is the optimum biodiesel–diesel blend based on no wall impingement (B15: 0% and B20 ±1.3% uncertainty limit) and increase in \\{NOx\\} emission (B15: 4.1% and B20: 15.6%) in a conventional (unmodified) diesel engine is up to B15.

Subhash Lahane; K.A. Subramanian

2015-01-01T23:59:59.000Z

318

Measurement and Meaning of Oxidatively Modified DNA Lesions in Urine  

Science Journals Connector (OSTI)

...commercially available kits presently on the market. Two are available from JICA, named...oxidative stress-inducing agents, such as diesel emission particles or potassium bromate...Moller P, et al. Repeated inhalations of diesel exhaust particles and oxidatively damaged...

Marcus S. Cooke; Ryszard Olinski; and Steffen Loft

2008-01-01T23:59:59.000Z

319

VehĂ­culos Diesel  

NLE Websites -- All DOE Office Websites (Extended Search)

Vehículos Diesel Vehículos Diesel Audi A3 Los vehículos Diesel podrían estar de regreso. Los motores de Diesel son más poderosos y ahorradores de gasolina en comparación con los motores de gasolina del mismo tamaño (un 30-35% aprox. más eficientes en su consumo). Además, los vehículos diesel son mejores que los que se fabricaban en el pasado. Mejor Desempeño Tienen mejores inyectores de combustible y tecnologías electrónicas en sus controles Más poder Aceleración Mejorada Más Eficiencia Los nuevos diseños en los motores, además de las tecnologías de reducción de ruido y vibración, los han hecho silenciosos y suaves en su manejo. El arranque en clima-frío también ha sido mejorado. Más Limpios Mercedes ML320 BlueTEC En la actualidad los diesels deben cumplir con los mismos estándares de

320

Advanced Particulate Filter Technologies for Direct Injection Gasoline Engine Applications  

Energy.gov (U.S. Department of Energy (DOE))

Specific designs and material properties have to be developed for gasoline particulate filters based on the different engine and exhaust gas characteristic of gasoline engines compared to diesel engines, e.g., generally lower levels of engine-out particulate emissions or higher GDI exhaust gas temperatures

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Inflammatory response of lung cells exposed to whole, filtered, and  

NLE Websites -- All DOE Office Websites (Extended Search)

Inflammatory response of lung cells exposed to whole, filtered, and Inflammatory response of lung cells exposed to whole, filtered, and hydrocarbon denuded diesel exhaust Title Inflammatory response of lung cells exposed to whole, filtered, and hydrocarbon denuded diesel exhaust Publication Type Journal Article Year of Publication 2007 Authors Holder, Amara L., Donald Lucas, Regine Goth-Goldstein, and Catherine P. Koshland Journal Chemosphere Volume 70 Pagination 13-19 Date Published 09/2007 Keywords air-liquid interface, combustion particle, human bronchial epithelial cells, interleukin-8 Abstract In vitro studies with the organic extracts of diesel particles have suggested that hydrocarbons such as PAH may play a role in an inflammatory response, but these have been limited by the possible artifacts introduced in the particle collection and processing. In this study, we avoid these artifacts and use an activated carbon denuder to remove hydrocarbons from the exhaust stream to investigate their role in the inflammatory response. Human bronchial epithelial cells (16HBE140) were exposed at the air-cell interface to diluted and aged exhaust from a diesel generator operated at partial and no load conditions. When particles were removed with a filter before cell exposure, exhaust gases accounted for almost half of the response compared to the whole exhaust. Removal of gas phase and a portion of the particle phase hydrocarbons with the denuder decreased the interleukin-8 (IL-8) secretion to unexposed levels

322

An oxygenating additive for improving the performance and emission characteristics of marine diesel engines  

Science Journals Connector (OSTI)

Diesel engines provide the major power sources for marine transportation and contribute to the prosperity of the worldwide economy. However, the emissions from diesel engines also seriously threaten the environment and are considered one of the major sources of air pollution. The pollutants emitted from marine vessels are confirmed to cause the ecological environmental problems such as the ozone layer destruction, enhancement of the greenhouse effect, and acid rain, etc. Marine diesel engine emissions such as particulate matter and black smoke carry carcinogen components that significantly impact the health of human beings. Investigations on reducing pollutants, in particular particulate matter and nitrogen oxides are critical to human health, welfare and continued prosperity. The addition of an oxygenating agent into fuel oil is one of the possible approaches for reducing this problem because of the obvious fuel oil constituent influences on engine emission characteristics. Ethylene glycol monoacetate was found to be a promising candidate primarily due to its low poison and oxygen-rich composition properties. In this experimental study ethylene glycol monoacetate was mixed with diesel fuel in various proportions to prepare oxygenated diesel fuel. A four-cylinder diesel engine was used to test the engine performance and emission characteristics. The influences of ethylene glycol monoacetate ration to diesel oil, inlet air temperature and humidity parameters on the engine’s speed and torque were considered. The experimental results show that an increase in the inlet air temperature caused an increase in brake specific fuel consumption (BSFC), carbon monoxide, carbon dioxide emission, and exhaust gas temperature, while decreasing the excess air, oxygen and nitrogen oxide emission concentrations. Increasing the inlet air humidity increased the carbon monoxide concentration while the decreased excess air, oxygen and nitrogen oxide emission concentrations. In addition, increasing ethylene glycol monoacetate ratio in the diesel fuel caused an increase in the BSFC while the excess air and oxygen emission concentrations decreased.

C.-Y. Lin; J.-C. Huang

2003-01-01T23:59:59.000Z

323

Hybrid Time Formulation for Diesel Blending and Distribution Scheduling  

Science Journals Connector (OSTI)

Hybrid Time Formulation for Diesel Blending and Distribution Scheduling ... Schematic of diesel in-line blending and distribution infrastructure. ...

Sérgio M. S. Neiro; Valéria V. Murata; José M. Pinto

2014-06-13T23:59:59.000Z

324

Advanced Diesel Common Rail Injection System for Future Emission Legislation  

Energy.gov (U.S. Department of Energy (DOE))

2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: Robert Bosch GMBH Common Rail System Engineering for PC Diesel Systems

325

Blowers for Air Assisted Diesel Particulate Filter Regeneration  

Energy.gov (U.S. Department of Energy (DOE))

Prototypes of a new series of high-pressure, brushless DC motor-drive blowers have completed field testing, and DFM and manufacturing cost studies are well advanced.

326

Tailored Acicular Mullite Substrates for Multifunctional Diesel Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE))

SEM analysis showed that ACM DPF can be coated with relatively high catalyst washcoat without significantly affecting the porosity or pore size Therefore, it maintains a low back pressure performance at very high catalyst

327

Substrate Studies of an Electrically-Assisted Diesel Particulate Filter  

Energy.gov (U.S. Department of Energy (DOE))

Transient distributed DPF wall and gas temperature were simultaneously measured using the optical and thermocouple systems, on both electrically assisted and conventional fuel-only DPF regeneration cycles

328

Versatile Diesel Particulate Filter Cartridge Any Size, Any Shape  

Energy.gov (U.S. Department of Energy (DOE))

Presentation given at DEER 2006, August 20-24, 2006, Detroit, Michigan. Sponsored by the U.S. DOE's EERE FreedomCar and Fuel Partnership and 21st Century Truck Programs.

329

Diesel Soot Filter Characterization and Modeling for Advanced Substrates  

Energy.gov (U.S. Department of Energy (DOE))

2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C.

330

Emissions and Durability of Underground Mining Diesel Particulate Filter Applications  

Energy.gov (U.S. Department of Energy (DOE))

Presentation given at DEER 2006, August 20-24, 2006, Detroit, Michigan. Sponsored by the U.S. DOE's EERE FreedomCar and Fuel Partnership and 21st Century Truck Programs.

331

CLEERS Activities: Diesel Soot Filter Characterization & NOx Control Fundamentals  

Energy.gov (U.S. Department of Energy (DOE))

2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C.

332

Durability of Diesel Engine Particulate Filters (Agreement ID:10461)  

Energy.gov (U.S. Department of Energy (DOE))

2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

333

Performance of the Low-Efficiency Diesel Particulate Filter for...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Directions in Engine-Efficiency and Emissions Research (DEER) Conference in Detroit, MI, September 27-30, 2010. p-15wei.pdf More Documents & Publications On-Road PM Mass...

334

Partial-Flow Diesel Particulate Filter of Sintered Metal Fiber...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Directions in Engine-Efficiency and Emissions Research (DEER) Conference in Detroit, MI, September 27-30, 2010. p-05lu.pdf More Documents & Publications Advanced Metal Fiber...

335

Development of SCR on Diesel Particulate Filter System for Heavy...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

with emission control has been introduced With proposed future regulations for GHG control and more emphasis on improved fuel economy, future engines will be designed...

336

Durability of Diesel Particulate Filters (Agreement ID:10461...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

(a zeolite based material). On-track (2) Initiate the determination of strength, fracture toughness, densityporositymicrostructure, and thermal expansion as a function of...

337

Durability of Diesel Engine Particulate Filters (Agreement ID...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 2013 AMR Milestones FY12 & FY13 * FY12: Complete the determination of strength, fracture toughness, densityporositymicrostructure, and thermal expansion of uncoated DPFs as...

338

Diesel Particulate Filter Technology for Low-Temperature and...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

for Low-Temperature and Low-NOxPM Applications 2004 DEER Conference Presentation: Johnson-Matthey Catalysts 2004deerchatterjee.pdf More Documents & Publications Performance...

339

Diesel Particulate Filter Technology for Low-Temperature and...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DEER Conference, 2004 Sougato Chatterjee, Ray Conway, Satish Viswanathan, Todd Jacobs Johnson Matthey Catalysts Environmental Catalysts & Technologies Outline * Introduction * CRT...

340

Diesel Particulate Filter: A Success for Faurecia Exhaust Systems  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technical Key points * FBC to lower the temperature of soot combustion process * Fresh nano-crystal catalyst is continuously delivered in the soot * Homogeneous Catalyst...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Filter loading corrections for real-time aethalometer measurements of fresh  

NLE Websites -- All DOE Office Websites (Extended Search)

Filter loading corrections for real-time aethalometer measurements of fresh Filter loading corrections for real-time aethalometer measurements of fresh diesel soot. (2007) Title Filter loading corrections for real-time aethalometer measurements of fresh diesel soot. (2007) Publication Type Journal Article Year of Publication 2007 Authors Jimenez, Jorge, Candis S. Claiborn, Timothy Larson, Thomas W. Kirchstetter, and Lara A. Gundel Journal Journal of Air and Waste Management Association Volume 57 Issue 7 Pagination 868-873 Abstract In this study, a correction was developed for the aethalometer to measure real-time black carbon (BC) concentrations in an environment dominated by fresh diesel soot. The relationship between the actual mass-specific absorption coefficient for BC and the BC-dependent attenuation coefficients was determined from experiments conducted in a diesel exposure chamber that provided constant concentrations of fine particulate matter (PM; PM(2.5); PM < 2.5 microm in aerodynamic diameter) from diesel exhaust. The aethalometer reported BC concentrations decreasing with time from 48.1 to 31.5 microg m(-3) when exposed to constant PM(2.5) concentrations of 55 +/- 1 microg m(-3) and b(scat) = 95 +/- 3 Mm(-1) from diesel exhaust. This apparent decrease in reported light-absorbing PM concentration was used to derive a correction K(ATN) for loading of strong light-absorbing particles onto or into the aethalometer filter tape, which was a function of attenuation of light at 880 nm by the embedded particles

342

Effects of Fuel Physical Properties on Diesel Engine Combustion Using Diesel and Bio-Diesel Fuels  

SciTech Connect

A computational study is performed to investigate the effects of physical property on diesel engine combustion characteristics using bio-diesel fuels. Properties of typical bio-diesel fuels that were either calculated or measured are used in the study and the simulation results are compared with those of conventional diesel fuels. Sensitivity of the computational results to individual physical properties is also investigated, and the results can provide information for desirable characteristics of the blended fuels. The properties considered in this study include liquid density, vapor pressure, surface tension, liquid viscosity, liquid thermal conductivity, liquid specific heat, latent heat, vapor specific heat, vapor diffusion coefficient, vapor viscosity and vapor thermal conductivity. The results show significant effects of the fuel physical properties on ignition delay and burning rates at various engine operating conditions. It is seen that there is no single physical property that dominates differences of ignition delay between diesel and bio-diesel fuels. However, among the 11 properties considered in the study, the simulation results were found to be most sensitive to the liquid fuel density, vapor pressure and surface tension through their effects on the mixture preparation processes.

Ra, Youngchul [ORNL; Reitz, Rolf [University of Wisconsin; McFarlane, Joanna [ORNL; Daw, C Stuart [ORNL

2007-01-01T23:59:59.000Z

343

On-Road Use of Fischer-Tropsch Diesel Blends  

SciTech Connect

Alternative compression ignition engine fuels are of interest both to reduce emissions and to reduce U.S. petroleum fuel demand. A Malaysian Fischer-Tropsch gas-to-liquid fuel was compared with California No.2 diesel by characterizing emissions from over the road Class 8 tractors with Caterpillar 3176 engines, using a chassis dynamometer and full scale dilution tunnel. The 5-Mile route was employed as the test schedule, with a test weight of 42,000 lb. Levels of oxides of nitrogen (NO{sub x}) were reduced by an average of 12% and particulate matter (PM) by 25% for the Fischer-Tropsch fuel over the California diesel fuel. Another distillate fuel produced catalytically from Fischer-Tropsch products originally derived from natural gas by Mossgas was also compared with 49-state No.2 diesel by characterizing emissions from Detroit Diesel 6V-92 powered transit buses, three of them equipped with catalytic converters and rebuilt engines, and three without. The CBD cycle was employed as the test schedule, with a test weight of 33,050 lb. For those buses with catalytic converters and rebuilt engines, NO x was reduced by 8% and PM was reduced by 31% on average, while for those buses without, NO x was reduced by 5% and PM was reduced by 20% on average. It is concluded that advanced compression ignition fuels from non-petroleum sources can offer environmental advantages in typical line haul and city transit applications.

Nigel Clark; Mridul Gautam; Donald Lyons; Chris Atkinson; Wenwei Xie; Paul Norton; Keith Vertin; Stephen Goguen; James Eberhardt

1999-04-26T23:59:59.000Z

344

(1) Land and Marine Diesel Engines (2) Diesel Enginesfor Land and Marine Work  

Science Journals Connector (OSTI)

... titles given above, it might be supposed that these two recently published treatises on the Diesel ...

A. J. M.

1916-04-20T23:59:59.000Z

345

Performance Characterization of a Medium-Duty Diesel Engine with Bio-Diesel and Petroleum Diesel Fuels  

E-Print Network (OSTI)

Torque Performance Curve. ...............35 Figure 9: Torque versus engine speed for conventional diesel fuel for 20%, 60%, and 75% loads....................................................................................36 Figure 10: Cycle fuel flow... versus engine speed for conventional diesel fuel for 20%, 60%, and 75% loads...........................................................................38 Figure 11: BSFC versus engine speed for conventional diesel fuel for 20%, 60%, and 75% load...

Esquivel, Jason

2010-01-16T23:59:59.000Z

346

Mortality among personnel exposed to diesel exhaust  

Science Journals Connector (OSTI)

Some epidemiological studies have suggested a carcinogenic effect from diesel exhausts and also an increased risk of cardiovascular ... undertaken to elucidate further the health effects of diesel exhaust exposur...

Christer Edling; Carl-Göran Anjou…

1987-09-01T23:59:59.000Z

347

Advanced Technology Light Duty Diesel Aftertreatment System ...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Approach to Low Temperature NOx Emission Abatement Cummins' Next Generation Tier 2, Bin 2 Light Truck Diesel Engine ATP-LD; Cummins Next Generation Tier 2 Bin 2 Diesel Engine...

348

Development and Applications of Catalyzed Diesel Particulate...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of Sd-Chemie c-DPF For BUG Emission Reduction * Test Cycle: ISO 8178 D2 Five Model * Diesel Engine: Cat 3406C, 350KW, 14liter, 1800rpm * Test Fuel: CARB 2 Diesel Fuel * 0...

349

Fuel Consumption Monitoring and Diesel Engines  

Science Journals Connector (OSTI)

In a perspective to explore how fuel monitoring and diesel engine life are interconnected, it’s necessary to ... touch several issues such as specifics of diesel engines in fuel consumption, the effects of precis...

Anna Antimiichuk

2014-09-01T23:59:59.000Z

350

THE FORTIETH ANNIVERSARY OF DIESEL POWER  

Science Journals Connector (OSTI)

...an internal combustion engine. His memory will be honored...York, is chairman of the Diesel com-mittee. Serving...Busch-Sulzer Brothers Diesel Engine Company. Colonel Robert...for the advancement of marine biology, not only by...

1936-11-27T23:59:59.000Z

351

Diesel prices top $4 per gallon  

U.S. Energy Information Administration (EIA) Indexed Site

Diesel prices top 4 per gallon The U.S. average retail price for on-highway diesel fuel surpassed the four dollar mark for the first time this year. Prices rose to 4.02 a gallon...

352

Ethanol fuel for diesel tractors  

SciTech Connect

The use of ethanol fuel in turbocharged diesel tractors is considered. The investigation was performed to evaluate the conversion of a diesel tractor for dual-fueling with ethanol by attaching a carburetor to the inlet air system or with the use of an alcohol spray-injection kit. In this system the mixture of water and alcohol is injected into the air stream by means of pressure from the turbocharger. The carburetor was attached to a by-pass apparatus which allowed the engine to start and shut off on diesel alone. Approximately 46% of the energy for the turbocharged 65 kW diesel tractor could be supplied by carbureted ethanol, and about 30% by the spray-injection approach. Knock limited the extent of substitution of ethanol for diesel fuel. The dual-fueling with ethanol caused a slight increase in brake thermal efficiency. Exhaust temperatures were much lower for equivalent high torque levels. Maximum power was increased by 36% with the spray-injection approach and about 59% with carburetion.

da Cruz, J.M.

1981-01-01T23:59:59.000Z

353

Elastomer Compatibility Testing of Renewable Diesel Fuels  

SciTech Connect

In this study, the integrity and performance of six elastomers were tested with ethanol-diesel and biodiesel fuel blends.

Frame, E.; McCormick, R. L.

2005-11-01T23:59:59.000Z

354

Diesel Power: Clean Vehicles for Tomorrow  

NLE Websites -- All DOE Office Websites (Extended Search)

Diesel Power: Diesel Power: Clean Vehicles for Tomorrow July 2010 VEHICLE TECHNOLOGIES PROGRAM Prepared for the U.S. Department of Energy Vehicle Technologies Program The diesel engine has changed significantly over the last quarter-century, in terms of technology and performance. For this reason, the U.S. Department of Energy (DOE) has created this series of documents about the history of the diesel engine, its current uses in transportation vehicles,

355

Value Analysis of Alternative Diesel Particulate Filter (DPF) Substrates for Future Diesel Aftertreatment Systems  

Energy.gov (U.S. Department of Energy (DOE))

DPF products like Acicular Mullite meet multiple needs Provide higher soot mass limits and durability than other materials at the same porosity.

356

Performance of the Low-Efficiency Diesel Particulate Filter for Diesel PM Reduction  

Energy.gov (U.S. Department of Energy (DOE))

Poster presented at the 16th Directions in Engine-Efficiency and Emissions Research (DEER) Conference in Detroit, MI, September 27-30, 2010.

357

Effect of idling on fuel consumption and emissions of a diesel engine fueled by Jatropha biodiesel blends  

Science Journals Connector (OSTI)

Abstract An engine running at low load and low rated speed is said to be subject to high idling conditions, a mode which represents one of the major problems currently the transport industry is facing. During this time, the engine can not work at peak operating temperature. This leads to incomplete combustion and emissions level increase due to having fuel residues in the exhaust. Also, idling results in increase in fuel consumption. The purpose of this study is to evaluate fuel consumption and emissions parameters under high idling conditions when diesel blended with Jatropha curcas biodiesel is used to operate a diesel engine. Although biodiesel–diesel blends decrease carbon monoxide and hydrocarbon emissions, they increase nitrogen oxides emissions in high idling modes. Compared to pure diesel fuel, fuel consumption also increases under all high idling conditions for biodiesel–diesel blends, with a further increase occurring as blend percentage rises.

S.M. Ashrafur Rahman; H.H. Masjuki; M.A. Kalam; M.J. Abedin; A. Sanjid; S. Imtenan

2014-01-01T23:59:59.000Z

358

Diesel Brewing | Open Energy Information  

Open Energy Info (EERE)

Diesel Brewing Diesel Brewing Jump to: navigation, search Name Diesel Brewing Place Salem, Oregon Zip 97302 Sector Biomass Product Oregon-based company that uses gasification to produce liquid fuels and electricity from non-food-based biomass sources, including wood wastes, agricultural residues, and manure. Coordinates 42.554485°, -88.110549° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.554485,"lon":-88.110549,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

359

Gasoline and Diesel Fuel Update  

Gasoline and Diesel Fuel Update (EIA)

Learn more... Learn more... Price trends and regional differences What causes fluctuations in motor gasoline prices? Retail gasoline prices are mainly affected by crude oil prices and the level of gasoline supply relative to demand. Strong and increasing demand for gasoline and other petroleum products in the United States and the rest of the world at times places intense pressure on available supplies. Even when crude oil prices are stable... read more in Gasoline Explained What causes fluctuations in diesel fuel oil prices? The retail price of a gallon of diesel fuel reflects the underlying costs and profits (or losses) of producing and delivering the product to customers. The price of diesel at the pump reflects the costs and profits of the entire production and distribution chain, including... read more in

360

Clean Coal Diesel Demonstration Project  

SciTech Connect

A Clean Coal Diesel project was undertaken to demonstrate a new Clean Coal Technology that offers technical, economic and environmental advantages over conventional power generating methods. This innovative technology (developed to the prototype stage in an earlier DOE project completed in 1992) enables utilization of pre-processed clean coal fuel in large-bore, medium-speed, diesel engines. The diesel engines are conventional modern engines in many respects, except they are specially fitted with hardened parts to be compatible with the traces of abrasive ash in the coal-slurry fuel. Industrial and Municipal power generating applications in the 10 to 100 megawatt size range are the target applications. There are hundreds of such reciprocating engine power-plants operating throughout the world today on natural gas and/or heavy fuel oil.

Robert Wilson

2006-10-31T23:59:59.000Z

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Vehicle Emissions Review - 2011 | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

NOx control, diesel oxidation catalysts, gasoline particulate filters deer11johnson.pdf More Documents & Publications Vehicle Emissions Review - 2012 Diesel Emission...

362

Impact of Biodiesel-Based Na on the Selective Catalytic Reduction (SCR) of NOx Using Cu-zeolite  

Energy.gov (U.S. Department of Energy (DOE))

Discusses the impact of Na in biodiesel on three emission control devices: the diesel particulate filter, diesel oxidation catalyst, and zeolyte-based SCR catalyst

363

Marine diesel generator from Yanmar  

SciTech Connect

A diesel generator series now available from Yanmar Diesel Engine Co. is designed to provide low fuel costs, direct burning of heavy fuel oil and long life in marine applications from 320 to 600 kW output. The new 6N18L generator sets are based on a six-cylinder, four-stroke, water-cooled engine (bore 180 x stroke 280 mm), which has rated speeds of 720 and 900 r/min. Compatible with mono-fuel ships, the generator engines are designed for operation on heavy fuels to 700 cSt (50{degree}C). This paper describes briefly the design and innovation of this system.

NONE

1996-03-01T23:59:59.000Z

364

Ethanol diesel dual fuel clean combustion with FPGA enabled control  

Science Journals Connector (OSTI)

Sophisticated engine controls have progressively become vital enablers for implementing clean and efficient combustion. The low temperature combustion in diesel engines is a viable combustion mode that offers ultra-low nitrogen oxides and dry soot emissions, yet only feasible under tightly controlled operating conditions. In this work, the dual fuel application of ethanol and diesel is studied for clean and efficient combustion. A set of real-time controllers has been configured to control the common-rail pressure and injection events, in concert with the use of two fuels in a high compression ratio diesel engine. An improved control algorithm has been implemented into the field programmable gate array devices to promptly execute the injection commands of the port and direct injection events. Such reliable and prompt control of fuel injection has been identified as critical to safely enable simultaneously low nitrogen oxides and soot combustion, especially when excessive or inadequate rate of exhaust gas recirculation is imminent. High load clean combustion was achieved with the improved control system.

Xiaoye Han; Jimi Tjong; Graham T. Reader; Ming Zheng

2014-01-01T23:59:59.000Z

365

Biodiesel and Other Renewable Diesel Fuels  

SciTech Connect

Present federal tax incentives apply to certain types of biomass-derived diesel fuels, which in energy policy and tax laws are described either as renewable diesel or biodiesel. To understand the distinctions between these diesel types it is necessary to understand the technologies used to produce them and the properties of the resulting products. This fact sheet contains definitions of renewable and biodiesel and discusses the processes used to convert biomass to diesel fuel and the properties of biodiesel and renewable diesel fuels.

Not Available

2006-11-01T23:59:59.000Z

366

An investigation of diesel–ignited propane dual fuel combustion in a heavy-duty diesel engine  

Science Journals Connector (OSTI)

Abstract This paper presents a detailed experimental analysis of diesel–ignited propane dual fuel combustion on a 12.9-l, six-cylinder, production heavy-duty diesel engine. Gaseous propane was fumigated upstream of the turbocharger air inlet and ignited using direct injection of diesel sprays. Results are presented for brake mean effective pressures (BMEP) from 5 to 20 bar and different percent energy substituted (PES) by propane at a constant engine speed of 1500 rpm. The effect of propane PES on apparent heat release rates, combustion phasing and duration, fuel conversion and combustion efficiencies, and engine-out emissions of oxides of nitrogen (NOx), smoke, carbon monoxide (CO), and total unburned hydrocarbons (HC) were investigated. Exhaust particle number concentrations and size distributions were also quantified for diesel–ignited propane combustion. With stock engine parameters, the maximum propane PES was limited to 86%, 60%, 33%, and 25% at 5, 10, 15, and 20 bar BMEPs, respectively, either by high maximum pressure rise rates (MPRR) or by excessive HC and CO emissions. With increasing PES, while fuel conversion efficiencies increased slightly at high \\{BMEPs\\} or decreased at low BMEPs, combustion efficiencies uniformly decreased. Also, with increasing PES, \\{NOx\\} and smoke emissions were generally decreased but these reductions were accompanied by higher HC and CO emissions. Exhaust particle number concentrations decreased with increasing PES at low loads but showed the opposite trends at higher loads. At 10 bar BMEP, by adopting a different fueling strategy, the maximum possible propane PES was extended to 80%. Finally, a limited diesel injection timing study was performed to identify the optimal operating conditions for the best efficiency-emissions-MPRR tradeoffs.

Andrew C. Polk; Chad D. Carpenter; Kalyan Kumar Srinivasan; Sundar Rajan Krishnan

2014-01-01T23:59:59.000Z

367

Reforming of Diesel Fuel for Transportation Applications J. P. Kopasz, S. Lottes, D-J. Liu, R. Ahluwalia, V. Novick and S. Ahmed  

E-Print Network (OSTI)

Reforming of Diesel Fuel for Transportation Applications J. P. Kopasz, S. Lottes, D-J. Liu, R · Produce fuel (H2-rich gas) for PEM and/or solid oxide fuel cells (SOFCs) · Reduce NOx emissions through

368

Federal Tax Credit for Diesels  

NLE Websites -- All DOE Office Websites (Extended Search)

Nuevos Reembolsos de impuestos en Materia de Energía para Nuevos Reembolsos de impuestos en Materia de Energía para Diesels Vehículo Diesel ¡Reembolso Federal de hasta $3,400! Algúnos diesels comprados o puestos en servicio después del 31 de diciembre del 2005 pueden ser elegibles para un reembolso de impuestos sobre la renta federal de hasta 3,400 dólares. (Ningún vehículo elegible fue fabricado para la venta hasta el 2008.) Las cantidades del reembolso comienzan a disminuir progresivamente para los fabricantes que hayan vendido más de 60,000 vehículos híbridos y diesel elegibles. Los vehículos adquiridos después de Diciembre 31 no son elegibles para este crédito. Audi BMW Mercedes-Benz Volkswagen All Marca y Modelo del Vehículo Reembolso Completo Desfase Sin Reembolso 50% 25% Audi ene. 1, 2006 jul. 1 - dic. 31, 2010 No aplica ene. 1, 2011

369

Coal-fired diesel generator  

SciTech Connect

The objective of the proposed project is to test the technical, environmental, and economic viability of a coal-fired diesel generator for producing electric power in small power generating markets. Coal for the diesel generator would be provided from existing supplies transported for use in the University`s power plant. A cleanup system would be installed for limiting gaseous and particulate emissions. Electricity and steam produced by the diesel generator would be used to supply the needs of the University. The proposed diesel generator and supporting facilities would occupy approximately 2 acres of land adjacent to existing coal- and oil-fired power plant and research laboratory buildings at the University of Alaska, Fairbanks. The environmental analysis identified that the most notable changes to result from the proposed project would occur in the following areas: power plant configuration at the University of Alaska, Fairbanks; air emissions, water use and discharge, and the quantity of solid waste for disposal; noise levels at the power plant site; and transportation of coal to the power plant. No substantive adverse impacts or environmental concerns were identified in analyzing the effects of these changes.

NONE

1997-05-01T23:59:59.000Z

370

Ceramic hot-gas filter  

DOE Patents (OSTI)

A ceramic hot-gas candle filter having a porous support of filament-wound oxide ceramic yarn at least partially surrounded by a porous refractory oxide ceramic matrix, and a membrane layer on at least one surface thereof. The membrane layer may be on the outer surface, the inner surface, or both the outer and inner surface of the porous support. The membrane layer may be formed of an ordered arrangement of circularly wound, continuous filament oxide ceramic yarn, a ceramic filler material which is less permeable than the filament-wound support structure, or some combination of continuous filament and filler material. A particularly effective membrane layer features circularly wound filament with gaps intentionally placed between adjacent windings, and a filler material of ceramic particulates uniformly distributed throughout the gap region. The filter can withstand thermal cycling during backpulse cleaning and is resistant to chemical degradation at high temperatures.

Connolly, Elizabeth Sokolinski (Wilmington, DE); Forsythe, George Daniel (Landenberg, PA); Domanski, Daniel Matthew (New Castle, DE); Chambers, Jeffrey Allen (Hockessin, DE); Rajendran, Govindasamy Paramasivam (Boothwyn, PA)

1999-01-01T23:59:59.000Z

371

Ceramic hot-gas filter  

DOE Patents (OSTI)

A ceramic hot-gas candle filter is described having a porous support of filament-wound oxide ceramic yarn at least partially surrounded by a porous refractory oxide ceramic matrix, and a membrane layer on at least one surface thereof. The membrane layer may be on the outer surface, the inner surface, or both the outer and inner surface of the porous support. The membrane layer may be formed of an ordered arrangement of circularly wound, continuous filament oxide ceramic yarn, a ceramic filler material which is less permeable than the filament-wound support structure, or some combination of continuous filament and filler material. A particularly effective membrane layer features circularly wound filament with gaps intentionally placed between adjacent windings, and a filler material of ceramic particulates uniformly distributed throughout the gap region. The filter can withstand thermal cycling during back pulse cleaning and is resistant to chemical degradation at high temperatures.

Connolly, E.S.; Forsythe, G.D.; Domanski, D.M.; Chambers, J.A.; Rajendran, G.P.

1999-05-11T23:59:59.000Z

372

Low Cost Autothermal Diesel Reforming Catalyst Development  

SciTech Connect

Catalytic autothermal reforming (ATR) represents an important step of converting fossil fuel to hydrogen rich reformate for use in solid oxide fuel cell (SOFC) stacks. The state-of-the-art reforming catalyst, at present, is a Rh based material which is effective but costly. The objective of our current research is to reduce the catalyst cost by finding an efficient ATR catalyst containing no rhodium. A group of perovskite based catalysts have been synthesized and evaluated under the reforming condition of a diesel surrogate fuel. Hydrogen yield, reforming efficiency, and conversion selectivity to carbon oxides of the catalyst ATR reaction are calculated and compared with the benchmark Rh based material. Several catalyst synthesis improvements were carried out including: 1) selectively doping metals on the A-site and B-site of the perovskite structure, 2) changing the support from perovskite to alumina, 3) altering the method of metal addition, and 4) using transition metals instead of noble metals. It was found that the catalytic activity changed little with modification of the A-site metal, while it displayed considerable dependence on the B-site metal. Perovskite supports performed much better than alumina based supports.

Shihadeh, J.; Liu, D.

2004-01-01T23:59:59.000Z

373

1999 2000 2001 2002 2003 2004... 2005 2006 gasoline diesel  

E-Print Network (OSTI)

1999 2000 2001 2002 2003 2004... 2005 2006 gasoline diesel price +10% gasolinegasoline gasoline diesel... ... 2007 20081998 2009 ...2010 home work home work diesel diesel ... gasoline diesel price -7, households' decisions are affected by various other factors, from the vehicle market offer to governmental

Bierlaire, Michel

374

Regional Modeling of the Atmospheric Fate and Transport of Benzene and Diesel Particles  

Science Journals Connector (OSTI)

It is oxidized in the atmosphere slowly by hydroxyl (OH) radicals; its atmospheric lifetime is on the order of 1 week. ... The surrogates used in this study include agriculture, airports, housing, major highways, ports, population, railroads, water, and land area. ... PM2.5 emissions from the 1996 EPA National Emission Trends (NET) were used to generate diesel particle emissions. ...

Christian Seigneur; Betty Pun; Kristen Lohman; Shiang-Yuh Wu

2003-10-17T23:59:59.000Z

375

Effects of Fuel Dilution with Biodiesel on Lubricant Acidity, Oxidation and Corrosion  

Energy.gov (U.S. Department of Energy (DOE))

In-cylinder fuel injection to produce rich exhaust for regeneration of lean NOx trap catalyst and diesel particulate filter results in substantial fuel dilution of lubricating oil cause changes of lubricating oil properties and scuffing of engine components.

376

Emissions comparison between petroleum diesel and biodiesel in a medium-duty diesel engine  

E-Print Network (OSTI)

EMISSIONS COMPARISON BETWEEN PETROLEUM DIESEL AND BIODIESEL IN A MEDIUM-DUTY DIESEL ENGINE A Thesis by BRANDON T. TOMPKINS Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE December 2008 Major Subject: Mechanical Engineering EMISSIONS COMPARISON BETWEEN PETROLEUM DIESEL AND BIODIESEL IN A MEDIUM-DUTY DIESEL ENGINE A Thesis by BRANDON T...

Tompkins, Brandon T.

2009-05-15T23:59:59.000Z

377

REVIEW OF DIESEL PARTICULATE MATTER SAMPLING METHODS Supplemental Report # 2  

E-Print Network (OSTI)

Arnold University of Minnesota Department of Mechanical Engineering Center for Diesel Research aerosol. This report focuses on the fundamental chemical and physical processes that affect diesel aerosolREVIEW OF DIESEL PARTICULATE MATTER SAMPLING METHODS Supplemental Report # 2 AEROSOL DYMAMICS

Minnesota, University of

378

Edinburgh Research Explorer Pulmonary diesel particulate increases susceptibility to  

E-Print Network (OSTI)

Edinburgh Research Explorer Pulmonary diesel particulate increases susceptibility to myocardial, MR & Gray, GA 2014, 'Pulmonary diesel particulate increases susceptibility to myocardial ischemia. Pulmonary diesel particulate increases susceptibility to myocardial ischemia/reperfusion injury via

Millar, Andrew J.

379

A Comparison of Combustion and Emissions of Diesel Fuels and...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

A Comparison of Combustion and Emissions of Diesel Fuels and Oxygenated Fuels in a Modern DI Diesel Engine A Comparison of Combustion and Emissions of Diesel Fuels and Oxygenated...

380

The California Demonstration Program for Control of PM from Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

of PM from Diesel Backup Generators Measuring "Real World" Heavy-Duty Diesel Emissions with a Mobile Lab Emissions from In-Use NG, Propane, and Diesel Fueled Heavy Duty Vehicles...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

2003 Diesel Engine Emissions Reduction (DEER) Conference Presentations...  

Energy Savers (EERE)

5: Diesel and CNG Bus Emissions Update on Diesel Exhaust Emission Control Timothy Johnson Corning, Inc. (PDF 1.53 MB) Summary of Swedish Experiences on CNG and "Clean" Diesel...

382

Response of Oil Sands Derived Fuels in Diesel HCCI Operation...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Response of Oil Sands Derived Fuels in Diesel HCCI Operation Response of Oil Sands Derived Fuels in Diesel HCCI Operation Presentation given at the 2007 Diesel Engine-Efficiency &...

383

Synthetic zeolites and other microporous oxide molecular sieves  

Science Journals Connector (OSTI)

...Many variations on the process cycle were developed to improve efficiency...NOx ) emitted from lean-burn diesel engines. Many catalyst developers...hydrocarbon oxidation in conventional diesel engines and NOx reduction...reduction and system durability. General Motors achieved 50,000-mile-aged...

John D. Sherman

1999-01-01T23:59:59.000Z

384

Gasoline and Diesel Fuel Update  

Gasoline and Diesel Fuel Update (EIA)

Sampling Methodology Sampling Methodology The sample design for the weekly diesel price survey was a two-phase design. The first phase constituted construction of a frame of 2,207 company-State units (CSUs) from the combination of two sample cycles of the EIA-782A and EIA-782B surveys that collected monthly petroleum products' sales at the State level. For sampling purposes, any combination of State and company where diesel was sold through retail outlets as reported on the EIA-782 surveys defined a CSU, the sampling unit. For the second phase, a sub-sample of the 2,207 CSUs from phase 1 was selected using probability proportional to size (PPS). The measure of size for each of the two sample cycles separately was normalized using the annual State sales' volumes from the monthly survey divided by the unit's

385

Gasoline and Diesel Fuel Update  

Gasoline and Diesel Fuel Update (EIA)

Sampling Methodology Sampling Methodology The respondents reporting to the weekly diesel price survey represent a stratified probability proportional to size (PPS) sample selected from a frame list of retail outlets. The outlet sampling frame was constructed using commercially available lists from several sources in order to provide comprehensive coverage of truck stops and service stations that sell on-highway diesel fuel in the United States. The frame includes about 62,000 service stations and 4,000 truck stops. Due to statistical and operational considerations, outlets in the States of Alaska and Hawaii are excluded from the target population. The primary publication cells of the survey include Petroleum Administration for Defense Districts (PADDs) 2-4, three sub-PADDs within

386

Effect of biodiesel fuels on diesel engine emissions  

Science Journals Connector (OSTI)

The call for the use of biofuels which is being made by most governments following international energy policies is presently finding some resistance from car and components manufacturing companies, private users and local administrations. This opposition makes it more difficult to reach the targets of increased shares of use of biofuels in internal combustion engines. One of the reasons for this resistance is a certain lack of knowledge about the effect of biofuels on engine emissions. This paper collects and analyzes the body of work written mainly in scientific journals about diesel engine emissions when using biodiesel fuels as opposed to conventional diesel fuels. Since the basis for comparison is to maintain engine performance, the first section is dedicated to the effect of biodiesel fuel on engine power, fuel consumption and thermal efficiency. The highest consensus lies in an increase in fuel consumption in approximate proportion to the loss of heating value. In the subsequent sections, the engine emissions from biodiesel and diesel fuels are compared, paying special attention to the most concerning emissions: nitric oxides and particulate matter, the latter not only in mass and composition but also in size distributions. In this case the highest consensus was found in the sharp reduction in particulate emissions.

Magín Lapuerta; Octavio Armas; José Rodríguez-Fernández

2008-01-01T23:59:59.000Z

387

Diesel pollution. (Latest citations from Pollution abstracts). Published Search  

SciTech Connect

The bibliography contains citations concerning pollution from diesel systems. Articles are included for automotive systems, large scale diesel generators, marine diesel engines, and other applications of diesel fuels. Citations examine the toxic and environmental effects of diesel fuels and diesel exhaust emissions from combustion sources. Pollution control measures from a fuel and post-combustion aspect are also considered. (Contains a minimum of 194 citations and includes a subject term index and title list.)

Not Available

1993-11-01T23:59:59.000Z

388

Diesel pollution. (Latest citations from Pollution Abstracts). Published Search  

SciTech Connect

The bibliography contains citations concerning pollution from diesel systems. Articles are included for automotive systems, large scale diesel generators, marine diesel engines, and other applications of diesel fuels. Citations examine the toxic and environmental effects of diesel fuels and diesel exhaust emissions from combustion sources. Pollution control measures from a fuel and post-combustion aspect are also considered. (Contains a minimum of 176 citations and includes a subject term index and title list.)

Not Available

1993-03-01T23:59:59.000Z

389

Diesel pollution. (Latest citations from Pollution abstracts). Published Search  

SciTech Connect

The bibliography contains citations concerning pollution from diesel systems. Articles are included for automotive systems, large scale diesel generators, marine diesel engines, and other applications of diesel fuels. Citations examine the toxic and environmental effects of diesel fuels and diesel exhaust emissions from combustion sources. Pollution control measures from a fuel and post-combustion aspect are also considered.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

NONE

1996-12-01T23:59:59.000Z

390

Diesel pollution. (Latest citations from Pollution abstracts). NewSearch  

SciTech Connect

The bibliography contains citations concerning pollution from diesel systems. Articles are included for automotive systems, large scale diesel generators, marine diesel engines, and other applications of diesel fuels. Citations examine the toxic and environmental effects of diesel fuels and diesel exhaust emissions from combustion sources. Pollution control measures from a fuel and post-combustion aspect are also considered. (Contains a minimum of 217 citations and includes a subject term index and title list.)

Not Available

1994-10-01T23:59:59.000Z

391

Staged direct injection diesel engine  

DOE Patents (OSTI)

A diesel engine having staged injection for using lower cetane number fuels than No. 2 diesel fuel. The engine includes a main fuel injector and a pilot fuel injector. Pilot and main fuel may be the same fuel. The pilot injector injects from five to fifteen percent of the total fuel at timings from 20.degree. to 180.degree. BTDC depending upon the quantity of pilot fuel injected, the fuel cetane number and speed and load. The pilot fuel injector is directed toward the centerline of the diesel cylinder and at an angle toward the top of the piston, avoiding the walls of the cylinder. Stratification of the early injected pilot fuel is needed to reduce the fuel-air mixing rate, prevent loss of pilot fuel to quench zones, and keep the fuel-air mixture from becoming too fuel lean to become effective. In one embodiment, the pilot fuel injector includes a single hole for injection of the fuel and is directed at approximately 48.degree. below the head of the cylinder.

Baker, Quentin A. (San Antonio, TX)

1985-01-01T23:59:59.000Z

392

Indiana: Improving Diesel Engine Performance for Trucks  

Office of Energy Efficiency and Renewable Energy (EERE)

Cummins, the world's largest diesel engine manufacturer, received funds from EERE to research advanced engine technology for heavy-duty and light-duty vehicles.

393

Particle Sensor for Diesel Combustion Monitoring | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Particulate Matter Sensor for HCCI and Conventional Diesel Engines High-Energy, Pulsed-Laser Diagnostics for Real-Time Measurements of Reciprocating Engine PM Emissions...

394

Diesel Engine Alternatives | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Alternatives Diesel Engine Alternatives 2003 DEER Conference Presentation: Southwest Research Institute 2003deerryan.pdf More Documents & Publications Combustion Targets for Low...

395

Photoacoustic insights on diesel exhaust particles  

Science Journals Connector (OSTI)

Photoacoustic measurements at General Motors Research Laboratories on diesel exhaust particulate emissions are reviewed. Conventional optical techniques provide real-time qualitative...

Roessler, David M

1984-01-01T23:59:59.000Z

396

Sources of Naphthalene in Diesel Exhaust Emissions  

Science Journals Connector (OSTI)

The sale of diesels now account for 20% of new car sales in the UK compared with just 6% in 1990.1 The increased popularity of diesel cars is in part owing to improved engine performance in terms of power output, greater fuel economy, and an improved public image in terms of noise and pollution levels. ... Diesel engines have greater emissions of particulate material than corresponding spark ignition (SI) engines. ... An understanding of the origin of PAH in diesel exhaust emissions is fundamental if adequate control of the emission of these compounds is to be achieved. ...

M. M. Rhead; R. D. Pemberton

1996-05-21T23:59:59.000Z

397

Diesel Engine Emission Reduction (DEER) Experiment | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Emission Reduction (DEER) Experiment Diesel Engine Emission Reduction (DEER) Experiment Presentation given at DEER 2006, August 20-24, 2006, Detroit, Michigan. Sponsored by the...

398

Further improvement of conventional diesel NOx aftertreatment...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

More Documents & Publications Future Directions in Engines and Fuels Diesel Passenger Car Technology for Low Emissions and CO2 Compliance A View from the Bridge...

399

Diesel Use in California | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Use in California Diesel Use in California 2002 DEER Conference Presentation: California Energy Commission 2002deerboyd.pdf More Documents & Publications Reducing Petroleum...

400

Diesel Technology - Challenges & Opportunities for North America...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Technology - Challenges & Opportunities for North America Diesel Technology - Challenges & Opportunities for North America Presentation given at DEER 2006, August 20-24, 2006,...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Chemical Kinetic Research on HCCI & Diesel Fuels  

Energy Savers (EERE)

fuel * a primary reference fuel for diesel * Include both high and low temperature chemistry important to model low temperature combustion modes Improve component models for...

402

An overview of utilizing water-in-diesel emulsion fuel in diesel engine and its potential research study  

Science Journals Connector (OSTI)

Abstract The need for more efficient energy usage and a less polluted environment are the prominent research areas that are currently being investigated by many researchers worldwide. Water-in-diesel emulsion fuel (W/D) is a promising alternative fuel that could fulfills such requests in that it can improve the combustion efficiency of a diesel engine and reduce harmful exhaust emission, especially nitrogen oxides (NOx) and particulate matter (PM). To date, there have been many W/D emulsion fuel studies, especially regarding performance, emissions and micro-explosion phenomena. This review paper gathers and discusses the recent advances in emulsion fuel studies in respect of the impact of W/D emulsion fuel on the performance and emission of diesel engines, micro-explosion phenomena especially the factors that affecting the onset and strength of micro-explosion process, and proposed potential research area in W/D emulsion fuel study. There is an inconsistency in the results reported from previous studies especially for the thermal efficiency, brake power, torque and specific fuel consumption. However, it is agreed by most of the studies that W/D does result in an improvement in these measurements when the total amount of diesel fuel in the emulsion is compared with that of the neat diesel fuel. \\{NOx\\} and PM exhaust gas emissions are greatly reduced by using the W/D emulsion fuel. Unburnt hydrocarbon (UHC) and carbon monoxide (CO) exhaust emissions are found to be increased by using the W/D emulsion fuel. The inconsistency of the experimental result can be related to the effects of the onset and the strength of the micro-explosion process. The factors that affect these measurements consist of the size of the dispersed water particle, droplet size of the emulsion, water-content in the emulsion, ambient temperature, ambient pressure, type and percentage of surfactant, type of diesel engine and engine operating conditions. Durability testing and developing the fuel production device that requires no/less surfactant are the potential research area that can be explored in future.

Ahmad Muhsin Ithnin; Hirofumi Noge; Hasannuddin Abdul Kadir; Wira Jazair

2014-01-01T23:59:59.000Z

403

Vehicle-emission characteristics using mechanically emulsified alcohol/diesel fuels  

SciTech Connect

A light-duty diesel vehicle fueled with an emulsified alcohol/diesel fuel was operated under cyclic mode. Emission and fuel economy measurements were taken during vehicle operation. The test results showed the volumetric fuel economy decreased slightly. Carbon monoxide emissions increased slightly, and oxides of nitrogen showed no significant change. Particulate emissions were reduced slightly, and the particulate extractables increased slightly. The environmental effect of these data cancel each other resulting in no significant changes in the total release of biological activity into the environment.

Allsup, J.R.; Seizinger, D.E.; Cox, F.W.; Brook, A.L.; McClellan, R.O.

1983-07-01T23:59:59.000Z

404

Performance and emission enhancements of a variable geometry turbocharger on a heavy-duty diesel engine  

Science Journals Connector (OSTI)

Variable Geometry Turbochargers (VGTs) have emerged in the heavy-duty diesel market with the simultaneous introduction of Exhaust Gas Recirculation (EGR) in meeting emission standards. From a military perspective, VGTs offer considerable promise of improving low speed torque and overall fuel economy. Despite these gains, nitric oxides (NOx) emissions generally increase with increased boost. During times when the military can reduce its environmental impact, VGTs can drive EGR and counter the increase in NOx emissions with relatively minor penalty in particulate matter (PM) emissions. This study highlights the performance and emission enhancements enabled by a VGT on a heavy-duty diesel engine.

Timothy J. Jacobs; Chad Jagmin; Wesley J. Williamson; Zoran S. Filipi; Dennis N. Assanis; Walter Bryzik

2008-01-01T23:59:59.000Z

405

Vehicle Technologies Office: 2004 Diesel Engine Emissions Reduction (DEER)  

NLE Websites -- All DOE Office Websites (Extended Search)

Diesel Engine Diesel Engine Emissions Reduction (DEER) Conference Presentations to someone by E-mail Share Vehicle Technologies Office: 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentations on Facebook Tweet about Vehicle Technologies Office: 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentations on Twitter Bookmark Vehicle Technologies Office: 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentations on Google Bookmark Vehicle Technologies Office: 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentations on Delicious Rank Vehicle Technologies Office: 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentations on Digg Find More places to share Vehicle Technologies Office: 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentations on

406

Fuel Efficiency and Emissions Optimization of Heavy-Duty Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

and Emissions Optimization of Heavy-Duty Diesel Engines using Model-Based Transient Calibration Fuel Efficiency and Emissions Optimization of Heavy-Duty Diesel Engines using...

407

Thermodynamic Systems for Tier 2 Bin 2 Diesel Engines | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Systems for Tier 2 Bin 2 Diesel Engines Thermodynamic Systems for Tier 2 Bin 2 Diesel Engines Discusses engine technology enablers that help achieve overall system integration...

408

Complete Fuel Combustion for Diesel Engines Resulting in Greatly...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Complete Fuel Combustion for Diesel Engines Resulting in Greatly Reduced Emissions and Improved Fuel Efficiency Complete Fuel Combustion for Diesel Engines Resulting in Greatly...

409

Advanced High Efficiency Clean Diesel Combustion with Low Cost...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Efficiency Clean Diesel Combustion with Low Cost for Hybrid Engines Advanced High Efficiency Clean Diesel Combustion with Low Cost for Hybrid Engines Clean, in-cylinder combustion...

410

Advanced Petroleum-Based fuels - Diesel Emissions Control (APBF...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Petroleum-Based fuels - Diesel Emissions Control (APBF-DEC) Activity Advanced Petroleum-Based fuels - Diesel Emissions Control (APBF-DEC) Activity 2003 DEER Conference...

411

Low-Temperature Diesel Combustion Cross-Cut Research | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Low-Temperature Diesel Combustion A Conceptual Model for Partially PremixedLow-Temperature Diesel Combustion Based onIn-Cylinder Laser Diagnostics and Chemical Kinetics Modeling...

412

Simplification of Diesel Emission Control System Packaging Using...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Simplification of Diesel Emission Control System Packaging Using SCR Coated on DPF Simplification of Diesel Emission Control System Packaging Using SCR Coated on DPF Study...

413

Technology Development for High Efficiency Clean Diesel Engines...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technology Development for High Efficiency Clean Diesel Engines and a Pathway to 50% Thermal Efficiency Technology Development for High Efficiency Clean Diesel Engines and a...

414

Cummins/DOE Light Truck Diesel Engine Progress Report | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Diesel Engine Progress Report CumminsDOE Light Truck Diesel Engine Progress Report 2002 DEER Conference Presentation: Cummins 2002deerstang.pdf More Documents & Publications...

415

Mixed-mode diesel HCCI with External Mixture Formation: Preliminary...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Mixed-mode diesel HCCI with External Mixture Formation: Preliminary Results Mixed-mode diesel HCCI with External Mixture Formation: Preliminary Results 2003 DEER Conference...

416

Low-Temperature Diesel Combustion Cross-Cut Research | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Low-Temperature Diesel Combustion Cross-Cut Research Low-Temperature Diesel Combustion Cross-Cut Research 2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review...

417

Mutagenicity of Diesel Exhaust Soot Dispersed in Phospholipid Surfactants  

Science Journals Connector (OSTI)

Organics extractable from respirable diesel exhaust soot particles by organic solvents have been ... a pulmonary alveolus or respiratory bronchiole, respirable diesel soot particles will contact first the hypopha...

W. Wallace; M. Keane; S. Xing; J. Harrison; M. Gautam; T. Ong

1990-01-01T23:59:59.000Z

418

The Effect of Changes in Diesel Exhaust Composition and After...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

The Effect of Changes in Diesel Exhaust Composition and After-Treatment Technology on Lung Inflammation and Resistance to Viral Infection The Effect of Changes in Diesel Exhaust...

419

Progress on DOE Vehicle Technologies Light-Duty Diesel Engine...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

DOE Vehicle Technologies Light-Duty Diesel Engine Efficiency and Emissions Milestones Progress on DOE Vehicle Technologies Light-Duty Diesel Engine Efficiency and Emissions...

420

Modeling of Diesel Exhaust Systems: A methodology to better simulate...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

of Diesel Exhaust Systems: A methodology to better simulate soot reactivity Modeling of Diesel Exhaust Systems: A methodology to better simulate soot reactivity Discussed...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Impact of Real Field Diesel Quality Variability on Engine Emissions...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Real Field Diesel Quality Variability on Engine Emissions and Fuel Consumption Solutions for Onboard Optimisation Impact of Real Field Diesel Quality Variability on Engine...

422

Dumping Dirty Diesels: The View From the Bridge | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Reduction (DEER) Conference Presentations and Posters 2005deerkassel.pdf More Documents & Publications EPA Diesel Update EPA Mobile Source Rule Update Cleaning Up Diesel Engines...

423

Onboard Plasmatron Generation of Hydrogen rich Gas for Diesel...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technology, Dr. S. Diamond ** Plasma Science and Fusion Center, MIT ***Sloan Automobile Laboratory, MIT Diesel Plasmatron Reformers * Enhanced conversion of diesel fuel...

424

Modeling Combustion Control for High Power Diesel Mode Switching  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and Emissions Research Conference 2010 Modeling Combustion Control for High Power Diesel Mode Switching P-20 Motivation * High power LTC-diesel mode operation * Transient...

425

Opportunity Assessment Clean Diesels in the North American Light...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Opportunity Assessment Clean Diesels in the North American Light Duty Market Opportunity Assessment Clean Diesels in the North American Light Duty Market Presentation given at the...

426

Advanced Diesel Engine Technology Development for HECC | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Diesel Engine Technology Development for HECC Advanced Diesel Engine Technology Development for HECC 2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and...

427

Heavy Duty Diesel Engine Exhaust Aerosol Particle and Ion Measurements  

Science Journals Connector (OSTI)

Heavy Duty Diesel Engine Exhaust Aerosol Particle and Ion Measurements ... diesel engines have received increasing attention due to their potential health effects. ...

Tero Lähde; Topi Rönkkö; Annele Virtanen; Tanja J. Schuck; Liisa Pirjola; Kaarle Hämeri; Markku Kulmala; Frank Arnold; Dieter Rothe; Jorma Keskinen

2008-12-09T23:59:59.000Z

428

Low-Temperature Automotive Diesel Combustion | Department of...  

Office of Environmental Management (EM)

in Low Temperature Automotive Diesel Combustion Systems Mixture Formation in a Light-Duty Diesel Engine Light Duty Combustion Research: Advanced Light-Duty Combustion Experiments...

429

A Correlation of Diesel Engine Performance with Measured NIR...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

A Correlation of Diesel Engine Performance with Measured NIR Fuel Characteristics A Correlation of Diesel Engine Performance with Measured NIR Fuel Characteristics Results indicate...

430

Update on Modeling for Effective Diesel Engine Aftertreatment...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Update on Modeling for Effective Diesel Engine Aftertreatment Implementation - Master Plan, Status and Critical Needs Update on Modeling for Effective Diesel Engine Aftertreatment...

431

Advances in Diesel Engine Technologies for European Passenger...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Advances in Diesel Engine Technologies for European Passenger Vehicles Advances in Diesel Engine Technologies for European Passenger Vehicles 2002 DEER Conference Presentation:...

432

Light Duty Diesels in the United States - Some Perspectives ...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005deerjohnson.pdf More Documents & Publications Update on Diesel Exhaust Emission...

433

Ricardo's ACTION Strategy: An Enabling Light Duty Diesel Technology...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

US Market 2005 Diesel Engine Emissions Reduction (DEER) Conference Presentations and Posters 2005deergreaney.pdf More Documents & Publications Light-Duty Diesel...

434

Oxygen-Enriched Combustion for Military Diesel Engine Generators...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Combustion for Military Diesel Engine Generators Oxygen-Enriched Combustion for Military Diesel Engine Generators Substantial increases in brake power and considerably lower peak...

435

The California Demonstration Program for Control of PM from Diesel...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Environmental Research and Technology EPA's AP-42 Emission Factors - Small Diesel SMALL DIESEL (< 600 hp) Emission Factor Emission Factor Emission Factor Emission (lbhp-hr) (g...

436

Microwave Regenerated DPF for Auxiliary Power Units and Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Microwave Regenerated DPF for Auxiliary Power Units and Diesel Hybrid Vehicles Microwave Regenerated DPF for Auxiliary Power Units and Diesel Hybrid Vehicles Microwave regeneration...

437

Modeling Combustion Control for High Power Diesel Mode Switching...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Combustion Control for High Power Diesel Mode Switching Modeling Combustion Control for High Power Diesel Mode Switching Poster presentation given at the 16th Directions in...

438

Optimization of an Advanced Passive/Active Diesel Emission Control...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

an Advanced PassiveActive Diesel Emission Control System Optimization of an Advanced PassiveActive Diesel Emission Control System Evaluation of PM exhaust aftertreatment...

439

Low Temperature Combustion and Diesel Emission Reduction Research...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Low Temperature Combustion and Diesel Emission Reduction Research Low Temperature Combustion and Diesel Emission Reduction Research Presentation given at DEER 2006, August 20-24,...

440

Light Duty Diesels in the United States - Some Perspectives ...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Emission Control Technology Review Update on Diesel Exhaust Emission Control Technology and Regulations Light Duty Diesels in the United States - Some Perspectives...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Recent Diesel Engine Emission Mitigation Activities of the Maritime...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Diesel Engine Emission Mitigation Activities of the Maritime Administration Energy Technologies Program Recent Diesel Engine Emission Mitigation Activities of the Maritime...

442

Dilute Clean Diesel Combustion Achieves Low Emissions and High...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Dilute Clean Diesel Combustion Achieves Low Emissions and High Efficiency While Avoiding Control Problems of HCCI Dilute Clean Diesel Combustion Achieves Low Emissions and High...

443

Measurement of diesel solid nanoparticle emissions using a catalytic...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

diesel solid nanoparticle emissions using a catalytic stripper for comparison with Europe's PMP protocol Measurement of diesel solid nanoparticle emissions using a catalytic...

444

Chassis Dynamometer Testing of Parallel and Series Diesel Hybrid Buses  

Energy.gov (U.S. Department of Energy (DOE))

Emissions and fuel economy data were studied from tests on four diesel and diesel hybrid transit buses using the Houston Metro Bus Cycle.

445

Low-Temperature Automotive Diesel Combustion | Department of...  

Energy Savers (EERE)

Diesel Combustion Low-Temperature Automotive Diesel Combustion 2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation...

446

Design Case Summary: Production of Gasoline and Diesel from Biomass...  

Energy Savers (EERE)

Design Case Summary: Production of Gasoline and Diesel from Biomass via Fast Pyrolysis, Hydrotreating, and Hydrocracking Design Case Summary: Production of Gasoline and Diesel from...

447

Production of Gasoline and Diesel from Biomass via Fast Pyrolysis...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Production of Gasoline and Diesel from Biomass via Fast Pyrolysis, Hydrotreating and Hydrocracking: A Design Case Production of Gasoline and Diesel from Biomass via Fast Pyrolysis,...

448

Fuel Additivies for Improved Performance of Diesel Aftertreatment...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Additivies for Improved Performance of Diesel Aftertreatment Systems Fuel Additivies for Improved Performance of Diesel Aftertreatment Systems 2002 DEER Conference Presentation:...

449

12TH DIESEL ENGINE-EFFICIENCY AND EMISSIONS RESEARCH CONFERENCE...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

2TH DIESEL ENGINE-EFFICIENCY AND EMISSIONS RESEARCH CONFERENCE (DEER 2006) PRESENTATIONS 12TH DIESEL ENGINE-EFFICIENCY AND EMISSIONS RESEARCH CONFERENCE (DEER 2006) PRESENTATIONS...

450

Chassis Dynamometer Testing of Parallel and Series Diesel Hybrid...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Chassis Dynamometer Testing of Parallel and Series Diesel Hybrid Buses Chassis Dynamometer Testing of Parallel and Series Diesel Hybrid Buses Emissions and fuel economy data were...

451

Real-Time Measurement of Diesel Trap Efficiency | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Update on 2007 Diesel Particulate Measurement Research 2007 Diesel Particulate Measurement Research (E-66 Project) Evaluation of the European PMP Methodologies Using...

452

Assessment of Health Hazards of Repeated Inhalation of Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Health Hazards of Repeated Inhalation of Diesel Emissions, with Comparisons to Other Source Emissions Assessment of Health Hazards of Repeated Inhalation of Diesel Emissions, with...

453

Update on Diesel Exhaust Emission Control Technology and Regulations  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Control Technology and Regulations Tim Johnson August 2004 2 Diesel emission control technology is making significant progress * Diesel regulations are getting tighter in all...

454

Diesel Emission Control in Review | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT). deer07johnson.pdf More Documents & Publications Update on Diesel Exhaust Emission Control Diesel...

455

Clean Diesel: The Progress, The Message, The Opportunity  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and are selling... and here's what people here's what people are saying are saying Image, Story Courtesy of Diesel Progress Washington Policymakers Have Seen the New Diesel...

456

Hydrogen Assisted Diesel Combustion in a Common Rail Turbodiesel...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Assisted Diesel Combustion in a Common Rail Turbodiesel Engine P-3 Hydrogen Assisted Diesel Combustion in a Common Rail Turbodiesel Engine P-3 Gregory Lilik, Jos Martn...

457

Hydrogen Assisted Diesel Combustion in a Common Rail Turbodiesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Assisted Diesel Combustion in a Common Rail Turbodiesel Engine Hydrogen Assisted Diesel Combustion in a Common Rail Turbodiesel Engine This study measured the effects of hydrogen...

458

Application of Synthetic Diesel Fuels | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The Potential of GTL Diesel to Meet Future Exhaust Emission Limits Performance Characteristics of Coal-to-Liquids (CTL) Diesel in a 50-State Emissions Compliant Passenger Car...

459

Effects of an Accelerated Diesel Engine Replacement/Retrofit Program  

E-Print Network (OSTI)

No. 894 Effects of an Accelerated Diesel Engine Replacement/2009 Effects of an Accelerated Diesel Engine Replacement/reductions occurring on an accelerated schedule compared to

Millstein, Dev E.; Harley, Robert A

2009-01-01T23:59:59.000Z

460

Performance Characteristics of Coal-to-Liquids (CTL) Diesel in...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Performance Characteristics of Coal-to-Liquids (CTL) Diesel in a 50-State Emissions Compliant Passenger Car Performance Characteristics of Coal-to-Liquids (CTL) Diesel in a...

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Optical Diagnostics and Modeling Tools Applied to Diesel HCCI...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Optical Diagnostics and Modeling Tools Applied to Diesel HCCI Optical Diagnostics and Modeling Tools Applied to Diesel HCCI 2002 DEER Conference Presentation: Caterpillar Engine...

462

Load Expansion with Diesel/Gasoline RCCI for Improved Engine...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

with DieselGasoline RCCI for Improved Engine Efficiency and Emissions Load Expansion with DieselGasoline RCCI for Improved Engine Efficiency and Emissions This poster will...

463

In Vitro Genotoxicity of Gasoline and Diesel Engine Vehicle Exhaust...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Gasoline and Diesel Engine Vehicle Exhaust Particulate and Semi-Volatile Organic Compound Materials In Vitro Genotoxicity of Gasoline and Diesel Engine Vehicle Exhaust Particulate...

464

Light-Duty Diesel Combustion | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Light-Duty Diesel Combustion Light-Duty Diesel Combustion 2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting...

465

The Impact of Oil Consumption Mechanisms on Diesel Exhaust Particle...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Oil Consumption Mechanisms on Diesel Exhaust Particle Size Distributions and Detailed Exhaust Chemical Composition The Impact of Oil Consumption Mechanisms on Diesel Exhaust...

466

Diesel Engine Oil Technology Insights and Opportunities | Department...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Oil Technology Insights and Opportunities Diesel Engine Oil Technology Insights and Opportunities Perrformance of API CJ-4 diesel engine lubricating oil and emerging lubricant...

467

Hydrogen generation from plasmatron reformers and use for diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

generation from plasmatron reformers and use for diesel exhaust aftertreatment Hydrogen generation from plasmatron reformers and use for diesel exhaust aftertreatment 2003 DEER...

468

Onboard Plasmatron Generation of Hydrogen rich Gas for Diesel...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Onboard Plasmatron Generation of Hydrogen rich Gas for Diesel Aftertreatment and Other Applications Onboard Plasmatron Generation of Hydrogen rich Gas for Diesel Aftertreatment and...

469

Membrane-Based Air Composition Control for Light-Duty Diesel Vehicles: A Benefit and Cost Assessment  

SciTech Connect

This report presents the methodologies and results of a study conducted by Argonne National Laboratory (Argonne) to assess the benefits and costs of several membrane-based technologies. The technologies evaluated will be used in automotive emissions-control and performance-enhancement systems incorporated into light-duty diesel vehicle engines. Such engines are among the technologies that are being considered to power vehicles developed under the government-industry Partnership for a New Generation of Vehicles (PNGV). Emissions of nitrogen oxides (NO{sub x}) from diesel engines have long been considered a barrier to use of diesels in urban areas. Recently, particulate matter (PM) emissions have also become an area of increased concern because of new regulations regarding emissions of particulate matter measuring 2.5 micrometers or less (PM{sub 2.5}). Particulates are of special concern for diesel engines in the PNGV program; the program has a research goal of 0.01 gram per mile (g/mi) of particulate matter emissions under the Federal Test Procedure (FTP) cycle. This extremely low level (one-fourth the level of the Tier II standard) could threaten the viability of using diesel engines as stand-alone powerplants or in hybrid-electric vehicles. The techniques analyzed in this study can reduce NO{sub x} and particulate emissions and even increase the power density of the diesel engines used in light-duty diesel vehicles.

K. Stork; R. Poola

1998-10-01T23:59:59.000Z

470

Effects of the blends containing low ratios of alternative fuels on the performance and emission characteristics of a diesel engine  

Science Journals Connector (OSTI)

The aim of this study is to experimentally investigate the effects of blends containing various alternative fuels and diesel fuel on the performance and emissions of a diesel engine. The considered parameters are brake power, specific fuel consumption and thermal efficiency as well as carbon monoxide, hydrocarbon and nitrogen oxide emissions. Blends of biodiesel, ethanol, methanol and vegetable oil with diesel fuel, each containing 15% alternative fuel in volume, were prepared. Then, these blends were tested in a naturally aspirated, direct injection diesel engine. The test results obtained with these blends were compared with those obtained with diesel fuel. It was found that the tested blends yielded usually different performance and emission characteristics compared to diesel fuel. The biodiesel blend resulted in performance parameters very close to those obtained in the use of diesel fuel. Ethanol and methanol blends yielded lower brake power, while they resulted in higher specific fuel consumption and lower carbon monoxide emissions. On the other hand, the vegetable oil blend yielded lower carbon monoxide emissions, while it caused only slight changes in the performance parameters.

Murat Karabektas; Gokhan Ergen; Murat Hosoz

2013-01-01T23:59:59.000Z

471

Comparing The Environmental Impacts Of Diesel Generated Electricity With Hybrid Diesel-Wind Electricity For Off Grid First Nation Communities In Ontario : Incorporating A Life Cycle Approach.  

E-Print Network (OSTI)

??The cost of diesel is rapidly increasing and the environmental impacts associated with diesel fuel combustion are substantial. Hybrid diesel-wind energy was found to be… (more)

Schofield, Jade

2011-01-01T23:59:59.000Z

472

Educating Consumers: New Content on Diesel Vehicles, Diesel Exhaust Fluid, and Selective Catalytic Reduction Technologies on the AFDC  

Energy.gov (U.S. Department of Energy (DOE))

Showcases new content added to the AFDC including: Diesel Vehicles, Diesel Exhaust Fluid, Selective Catalytic Reduction Technologies, and an upcoming Deisel Exhaust Fluid Locator.

473

Black Carbon Concentrations and Diesel Vehicle Emission Factors Derived from Coefficient of Haze Measurements in California: 1967-2003  

SciTech Connect

We have derived ambient black carbon (BC) concentrations and estimated emission factors for on-road diesel vehicles from archived Coefficient of Haze (COH) data that was routinely collected beginning in 1967 at 11 locations in the San Francisco Bay Area. COH values are a measure of the attenuation of light by particles collected on a white filter, and available data indicate they are proportional to BC concentrations measured using the conventional aethalometer. Monthly averaged BC concentrations are up to five times greater in winter than summer, and, consequently, so is the population?s exposure to BC. The seasonal cycle in BC concentrations is similar for all Bay Area sites, most likely due to area-wide decreased pollutant dispersion during wintertime. A strong weekly cycle is also evident, with weekend concentrations significantly lower than weekday concentrations, consistent with decreased diesel traffic volume on weekends. The weekly cycle suggests that, in the Bay Area, diesel vehicle emissions are the dominant source of BC aerosol. Despite the continuous increase in diesel fuel consumption in California, annual Bay Area average BC concentrations decreased by a factor of ~;;3 from the late 1960s to the early 2000s. Based on estimated annual BC concentrations, on-road diesel fuel consumption, and recent measurements of on-road diesel vehicle BC emissions, diesel BC emission factors decreased by an order of magnitude over the study period. Reductions in the BC emission factor reflect improved engine technology, emission controls and changes in diesel fuel composition. A new BC monitoring network is needed to continue tracking ambient BC trends because the network of COH monitors has recently been retired.

Tast, CynthiaL; Kirchstetter, Thomas W.; Aguiar, Jeffery; Tonse, Shaheen; Novakov, T.; Fairley, David

2007-11-09T23:59:59.000Z

474

Black Carbon Concentrations and Diesel Vehicle Emission FactorsDerived from Coefficient of Haze Measurements in California:1967-2003  

SciTech Connect

We have derived ambient black carbon (BC) concentrations and estimated emission factors for on-road diesel vehicles from archived Coefficient of Haze (COH) data that was routinely collected beginning in 1967 at 11 locations in the San Francisco Bay Area. COH values are a measure of the attenuation of light by particles collected on a white filter, and available data indicate they are proportional to BC concentrations measured using the conventional aethalometer. Monthly averaged BC concentrations are up to five times greater in winter than summer, and, consequently, so is the population's exposure to BC. The seasonal cycle in BC concentrations is similar for all Bay Area sites, most likely due to area-wide decreased pollutant dispersion during wintertime. A strong weekly cycle is also evident, with weekend concentrations significantly lower than weekday concentrations, consistent with decreased diesel traffic volume on weekends. The weekly cycle suggests that, in the Bay Area, diesel vehicle emissions are the dominant source of BC aerosol. Despite the continuous increase in diesel fuel consumption in California, annual Bay Area average BC concentrations decreased by a factor of {approx}3 from the late 1960s to the early 2000s. Based on estimated annual BC concentrations, on-road diesel fuel consumption, and recent measurements of on-road diesel vehicle BC emissions, diesel BC emission factors decreased by an order of magnitude over the study period. Reductions in the BC emission factor reflect improved engine technology, emission controls and changes in diesel fuel composition. A new BC monitoring network is needed to continue tracking ambient BC trends because the network of COH monitors has recently been retired.

Kirchstetter, Thomas W.; Aguiar, Jeffery; Tonse, Shaheen; Novakov, T.

2007-10-01T23:59:59.000Z

475

Premixed ignition behavior of alternative diesel fuel-relevant compounds in a motored engine experiment  

SciTech Connect

A motored engine study using premixed charges of fuel and air at a wide range of diesel-relevant equivalence ratios was performed to investigate autoignition differences among surrogates for conventional diesel fuel, gas-to-liquid (GTL) diesel fuel, and biodiesel, as well as n-heptane. Experiments were performed by delivering a premixed charge of vaporized fuel and air and increasing the compression ratio in a stepwise manner to increase the extent of reaction while monitoring the exhaust composition via Fourier transform infrared (FTIR) spectrometry and collecting condensable exhaust gas for subsequent gas chromatography/mass spectrometry (GC/MS) analysis. Each fuel demonstrated a two-stage ignition process, with a low-temperature heat release (LTHR) event followed by the main combustion, or high-temperature heat release (HTHR). Among the three diesel-relevant fuels, the magnitude of LTHR was highest for GTL diesel, followed by methyl decanoate, and conventional diesel fuel last. FTIR analysis of the exhaust for n-heptane, the conventional diesel surrogate, and the GTL diesel surrogate revealed that LTHR produces high concentrations of aldehydes and CO while producing only negligible amounts of CO{sub 2}. Methyl decanoate differed from the other two-stage ignition fuels only in that there were significant amounts of CO{sub 2} produced during LTHR; this was the result of decarboxylation of the ester group, not the result of oxidation. GC/MS analysis of LTHR exhaust condensate for n-heptane revealed high concentrations of 2,5-heptanedione, a di-ketone that can be closely tied to species in existing autoignition models for n-heptane. GC/MS analysis of the LTHR condensate for conventional diesel fuel and GTL diesel fuel revealed a series of high molecular weight aldehydes and ketones, which were expected, as well as a series of organic acids, which are not commonly reported as products of combustion. The GC/MS analysis of the methyl decanoate exhaust condensate revealed that the aliphatic chain acts similarly to n-paraffins during LTHR, while the ester group remains intact. Thus, although the FTIR data revealed that decarboxylation occurs at significant levels for methyl decanoate, it was concluded that this occurs after the aliphatic chain has been largely consumed by other LTHR reactions. (author)

Szybist, James P.; Boehman, Andre L.; Haworth, Daniel C. [Pennsylvania State University, Fuel Science Program, 405 Academic Activities Building, University Park, PA 16802 (United States); Koga, Hibiki [Honda R and D Company, Ltd., Asaka-shi, Saitama 351-0024 (Japan)

2007-04-15T23:59:59.000Z

476

Color Degradation of Hydrocracked Diesel Fuel  

Science Journals Connector (OSTI)

Color Degradation of Hydrocracked Diesel Fuel ... An important quality standard to be examined is the color of diesels, given the fact that consumers tend to relate a dark colored fuel to low quality fuel, where the dark color comes from the fuels aging. ...

Isabelle Bergeron; Jean-Pierre Charland; Marten Ternan

1999-04-17T23:59:59.000Z

477

Combustion Modeling for Diesel Engine Control Design  

E-Print Network (OSTI)

Combustion Modeling for Diesel Engine Control Design Von der Fakult¨at f¨ur Maschinenwesen der Combustion Modeling for Diesel Engine Control Design WICHTIG: D 82 überprüfen !!! #12;Bibliographic research stays at General Motors R&D in Warren, MI, USA, possible. Furthermore, I would like thank Tom

Peters, Norbert

478

Gas Filter Testing Methods  

Science Journals Connector (OSTI)

Gas filtration of air in the cleanroom is carried out with HEPA (high- ... filter. The ambient air filters for the cleanroom are relatively fragile and require great care...

Alvin Lieberman

1992-01-01T23:59:59.000Z

479

Thermal and Oxidative Degradation of Castor Oil Biodiesel  

Science Journals Connector (OSTI)

Thermal and Oxidative Degradation of Castor Oil Biodiesel ... The neat biodiesels, 20% blends, and the base fuel (No. 2 diesel) were tested at 2 different loads (100 and 20%) and 3 injection timings (3° advanced, std., 3° retarded). ...

Marta M. Conceiçăo; Valter J. Fernandes, Jr.; Antonio S. Araújo; Mirna F. Farias; Ieda M. G. Santos; Antonio G. Souza

2007-03-23T23:59:59.000Z

480

Clean Diesel Technologies Inc | Open Energy Information  

Open Energy Info (EERE)

Diesel Technologies Inc Diesel Technologies Inc Jump to: navigation, search Name Clean Diesel Technologies Inc Place Stamford, Connecticut Zip 6901 Product Clean Diesel Technologies Inc is a specialty chemical company with patented products that reduce emissions from diesel engines while simultaneously improving fuel economy and power. Coordinates 42.75294°, -73.068531° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.75294,"lon":-73.068531,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

Note: This page contains sample records for the topic "filters diesel oxidation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Investigation of a Fatality Due to Diesel Fuel No. 2 Ingestion  

Science Journals Connector (OSTI)

......diesel oil No. 2. Diesel fuel No. 4 is marine diesel fuel or distillate marine diesel fuel (1,4). Diesel fuel No. 2 (CAS 68476-34-6...naphtalenes (dominant) to phenanthrenes. Some marine diesel fuels may content higher levels. Diesel fuel No......

María A. Martínez; Salomé Ballesteros

2006-10-01T23:59:59.000Z

482

Robust Strategy for Intake Leakage Detection in Diesel Engines  

E-Print Network (OSTI)

Robust Strategy for Intake Leakage Detection in Diesel Engines Riccardo Ceccarelli , Philippe are provided using advanced Diesel engine developed under AMEsim. I. INTRODUCTION The modern Diesel engine has of the functioning of a air-path in a Diesel engine with exhaust gas recirculation circuit is presented. More

Boyer, Edmond

483

Neural-Network-Based Maintenance Decision Model for Diesel Engine  

Science Journals Connector (OSTI)

To decrease the fuzzy and uncertain factors in the maintenance decision models of diesel engine, a combination BP-neural-network-based maintenance decision model for diesel engine is presented in this paper. It can make the maintenance of diesel engine ... Keywords: Deterioration degree, Diesel engine, Maintenance decision, Neural network

Yingkui Gu; Juanjuan Liu; Shuyun Tang

2008-09-01T23:59:59.000Z

484

REVIEW OF DIESEL PARTICULATE MATTER SAMPLING METHODS Supplemental Report # 1  

E-Print Network (OSTI)

.D. and Megan Arnold University of Minnesota Department of Mechanical Engineering Center for Diesel Research obtained from engine laboratory visits and present results from a diesel aerosol sampling questionnaireREVIEW OF DIESEL PARTICULATE MATTER SAMPLING METHODS Supplemental Report # 1 DIESEL EXHAUST

Minnesota, University of

485

Diesel Engine Waste Heat Recovery Utilizing Electric Turbocompound Technology  

Energy.gov (U.S. Department of Energy (DOE))

2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: Caterpillar/U.S. Department of Energy

486

Technology Development for Light Duty High Efficient Diesel Engines  

Energy.gov (U.S. Department of Energy (DOE))

Improve the efficiency of diesel engines for light duty applications through technical advances in system optimization.

487

Partitioning of Volatile Organics in Diesel Particulate and Exhaust  

Energy.gov (U.S. Department of Energy (DOE))

Evaluation of how sampling details affect the measurement of volatile organic compounds in diesel exhaust

488

Effect of GTL Diesel Fuels on Emissions and Engine Performance  

Energy.gov (U.S. Department of Energy (DOE))

2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: DaimlerChrysler Research and Technology

489

Active Diesel Emission Control Technology for Transport Refrigeration Units  

Energy.gov (U.S. Department of Energy (DOE))

This project discusses a CARB Level 2+ verified active regeneration technology for smal diesel engines

490

Ceramic Particulate Filters  

Energy.gov (U.S. Department of Energy (DOE))

Poster presentation at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT).

491

Vehicle Technologies Office: 2008 Diesel Engine-Efficiency and Emissions  

NLE Websites -- All DOE Office Websites (Extended Search)

8 Diesel 8 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations to someone by E-mail Share Vehicle Technologies Office: 2008 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Facebook Tweet about Vehicle Technologies Office: 2008 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Twitter Bookmark Vehicle Technologies Office: 2008 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Google Bookmark Vehicle Technologies Office: 2008 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Delicious Rank Vehicle Technologies Office: 2008 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Digg

492

Vehicle Technologies Office: 2007 Diesel Engine-Efficiency and Emissions  

NLE Websites -- All DOE Office Websites (Extended Search)

7 Diesel 7 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations to someone by E-mail Share Vehicle Technologies Office: 2007 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Facebook Tweet about Vehicle Technologies Office: 2007 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Twitter Bookmark Vehicle Technologies Office: 2007 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Google Bookmark Vehicle Technologies Office: 2007 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Delicious Rank Vehicle Technologies Office: 2007 Diesel Engine-Efficiency and Emissions Research (DEER) Conference Presentations on Digg

493

Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Biodiesel Biodiesel Printable Version Share this resource Send a link to Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel to someone by E-mail Share Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel on Facebook Tweet about Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel on Twitter Bookmark Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel on Google Bookmark Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel on Delicious Rank Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel on Digg Find More places to share Alternative Fuels Data Center: Diesel Vehicles Using Biodiesel on AddThis.com... More in this section... Biodiesel Basics Benefits & Considerations Stations Vehicles Availability Emissions

494

Loading Effect Correction for Real-time Aethalometer Measurements of Fresh Diesel Soot  

SciTech Connect

In this study, a correction was developed for the aethalometer to measure real-time black carbon (BC) concentrations in an environment dominated by fresh diesel soot. The relationship between the actual mass-specific absorption coefficient for BC and the BC-dependent attenuation coefficients was determined from experiments conducted in a diesel exposure chamber that provided constant concentrations of fine particulate matter (PM; PM(2.5); PM < 2.5 microm in aerodynamic diameter) from diesel exhaust. The aethalometer reported BC concentrations decreasing with time from 48.1 to 31.5 microg m(-3) when exposed to constant PM(2.5) concentrations of 55 +/- 1 microg m(-3) and b(scat) = 95 +/- 3 Mm(-1) from diesel exhaust. This apparent decrease in reported light-absorbing PM concentration was used to derive a correction K(ATN) for loading of strong light-absorbing particles onto or into the aethalometer filter tape, which was a function of attenuation of light at 880 nm by the embedded particles.

Jimenez, Jorge; Claiborn, Candis; Larson, Timothy; Gould, Timothy; Kirchstetter, Thomas W.; Gundel, Lara

2007-04-01T23:59:59.000Z

495

Effect of Biodiesel Blending on the Speciation of Soluble Organic Fraction from a Light Duty Diesel Engine  

SciTech Connect

Soy methyl ester (SME) biodiesel was volumetrically blended with 2007 certification ultra low sulfur diesel (ULSD) fuel and run in a 1.7L direct-injection common rail diesel engine at one speed-load point (1500rpm, 2.6bar BMEP). Engine fueling rate and injection timing were adjusted to maintain a constant load, while particulate samples were collected in a diesel particulate filter (DPF) and with a dilution tunnel sampling train. The samples collected at these two locations were found to contain different levels of soluble organic fraction (SOF) and the different hydrocarbon species in the SOF. This observation indicates that traditional SOF measurements, in light of the specific sampling procedure used, may not be appropriate to DPF applications.

Strzelec, Andrea [ORNL] [ORNL; Storey, John Morse [ORNL] [ORNL; Lewis Sr, Samuel Arthur [ORNL] [ORNL; Daw, C Stuart [ORNL] [ORNL; Foster, Prof. Dave [University of Wisconsin] [University of Wisconsin; Rutland, Prof. Christopher J. [University of Wisconsin] [University of Wisconsin

2010-01-01T23:59:59.000Z

496

Alternative Fuels Data Center: Diesel Fuel Blend Tax Exemption  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Diesel Fuel Blend Tax Diesel Fuel Blend Tax Exemption to someone by E-mail Share Alternative Fuels Data Center: Diesel Fuel Blend Tax Exemption on Facebook Tweet about Alternative Fuels Data Center: Diesel Fuel Blend Tax Exemption on Twitter Bookmark Alternative Fuels Data Center: Diesel Fuel Blend Tax Exemption on Google Bookmark Alternative Fuels Data Center: Diesel Fuel Blend Tax Exemption on Delicious Rank Alternative Fuels Data Center: Diesel Fuel Blend Tax Exemption on Digg Find More places to share Alternative Fuels Data Center: Diesel Fuel Blend Tax Exemption on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Diesel Fuel Blend Tax Exemption The biodiesel or ethanol portion of blended fuel containing taxable diesel

497

Recirculating electric air filter  

DOE Patents (OSTI)

An electric air filter cartridge has a cylindrical inner high voltage electrode, a layer of filter material, and an outer ground electrode formed of a plurality of segments moveably connected together. The outer electrode can be easily opened to remove or insert filter material. Air flows through the two electrodes and the filter material and is exhausted from the center of the inner electrode.

Bergman, W.

1985-01-09T23:59:59.000Z

498

Hepa filter dissolution process  

DOE Patents (OSTI)

A process for dissolution of spent high efficiency particulate air (HEPA) filters and then combining the complexed filter solution with other radioactive wastes prior to calcining the mixed and blended waste feed. The process is an alternate to a prior method of acid leaching the spent filters which is an inefficient method of treating spent HEPA filters for disposal.

Brewer, Ken N. (Arco, ID); Murphy, James A. (Idaho Falls, ID)

1994-01-01T23:59:59.000Z

499

High-Energy Laser Diagnostics (HELD) for the Measurement of Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Energy Laser Diagnostics (HELD) for the Measurement of Diesel Particulate Matter High-Energy Laser Diagnostics (HELD) for the Measurement of Diesel Particulate Matter 2004 Diesel...

500

Optimization of combustion performance and emission of Jatropha biodiesel in a turbocharged LHR diesel engine;.  

E-Print Network (OSTI)

??Bio-diesel derived from the vegetable oils are identified as an excellent alternate fuel for petroleum based diesel fuel used in diesel engines. However, the performance… (more)

Rajendra Prasath B

2013-01-01T23:59:59.000Z