Powered by Deep Web Technologies
Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Hydrogen Filling Station  

SciTech Connect (OSTI)

Hydrogen is an environmentally attractive transportation fuel that has the potential to displace fossil fuels. The Freedom CAR and Freedom FUEL initiatives emphasize the importance of hydrogen as a future transportation fuel. Presently, Las Vegas has one hydrogen fueling station powered by natural gas. However, the use of traditional sources of energy to produce hydrogen does not maximize the benefit. The hydrogen fueling station developed under this grant used electrolysis units and solar energy to produce hydrogen fuel. Water and electricity are furnished to the unit and the output is hydrogen and oxygen. Three vehicles were converted to utilize the hydrogen produced at the station. The vehicles were all equipped with different types of technologies. The vehicles were used in the day-to-day operation of the Las Vegas Valley Water District and monitoring was performed on efficiency, reliability and maintenance requirements. The research and demonstration utilized for the reconfiguration of these vehicles could lead to new technologies in vehicle development that could make hydrogen-fueled vehicles more cost effective, economical, efficient and more widely used. In order to advance the development of a hydrogen future in Southern Nevada, project partners recognized a need to bring various entities involved in hydrogen development and deployment together as a means of sharing knowledge and eliminating duplication of efforts. A road-mapping session was held in Las Vegas in June 2006. The Nevada State Energy Office, representatives from DOE, DOE contractors and LANL, NETL, NREL were present. Leadership from the National hydrogen Association Board of Directors also attended. As a result of this session, a roadmap for hydrogen development was created. This roadmap has the ability to become a tool for use by other road-mapping efforts in the hydrogen community. It could also become a standard template for other states or even countries to approach planning for a hydrogen future. Project partners also conducted a workshop on hydrogen safety and permitting. This provided an opportunity for the various permitting agencies and end users to gather to share experiences and knowledge. As a result of this workshop, the permitting process for the hydrogen filling station on the Las Vegas Valley Water District’s land was done more efficiently and those who would be responsible for the operation were better educated on the safety and reliability of hydrogen production and storage. The lessons learned in permitting the filling station and conducting this workshop provided a basis for future hydrogen projects in the region. Continuing efforts to increase the working pressure of electrolysis and efficiency have been pursued. Research was also performed on improving the cost, efficiency and durability of Proton Exchange Membrane (PEM) hydrogen technology. Research elements focused upon PEM membranes, electrodes/catalysts, membrane-electrode assemblies, seals, bipolar plates, utilization of renewable power, reliability issues, scale, and advanced conversion topics. Additionally, direct solar-to-hydrogen conversion research to demonstrate stable and efficient photoelectrochemistry (PEC) hydrogen production systems based on a number of optional concepts was performed. Candidate PEC concepts included technical obstacles such as inefficient photocatalysis, inadequate photocurrent due to non-optimal material band gap energies, rapid electron-hole recombination, reduced hole mobility and diminished operational lifetimes of surface materials exposed to electrolytes. Project Objective 1: Design, build, operate hydrogen filling station Project Objective 2: Perform research and development for utilizing solar technologies on the hydrogen filling station and convert two utility vehicles for use by the station operators Project Objective 3: Increase capacity of hydrogen filling station; add additional vehicle; conduct safety workshop; develop a roadmap for hydrogen development; accelerate the development of photovoltaic components Project Objective 4:

Boehm, Robert F; Sabacky, Bruce; Anderson II, Everett B; Haberman, David; Al-Hassin, Mowafak; He, Xiaoming; Morriseau, Brian

2010-02-24T23:59:59.000Z

2

Spin exchange optical pumping based polarized {sup 3}He filling station for the Hybrid Spectrometer at the Spallation Neutron Source  

SciTech Connect (OSTI)

The Hybrid Spectrometer (HYSPEC) is a new direct geometry spectrometer at the Spallation Neutron Source at the Oak Ridge National Laboratory. This instrument is equipped with polarization analysis capability with 60 Degree-Sign horizontal and 15 Degree-Sign vertical detector coverages. In order to provide wide angle polarization analysis for this instrument, we have designed and built a novel polarized {sup 3}He filling station based on the spin exchange optical pumping method. It is designed to supply polarized {sup 3}He gas to HYSPEC as a neutron polarization analyzer. In addition, the station can optimize the {sup 3}He pressure with respect to the scattered neutron energies. The depolarized {sup 3}He gas in the analyzer can be transferred back to the station to be repolarized. We have constructed the prototype filling station. Preliminary tests have been carried out demonstrating the feasibility of the filling station. Here, we report on the design, construction, and the preliminary results of the prototype filling station.

Jiang, C. Y.; Tong, X.; Brown, D. R.; Culbertson, H.; Kadron, B.; Robertson, J. L. [Instrument and Source Design Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Graves-Brook, M. K. [Research Accelerator Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Hagen, M. E. [Neutron Data Analysis and Visualization Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Lee, W. T. [Australian Nuclear Science and Technology Organisation, New Illawarra Road, Lucas Heights, NSW 2234 (Australia); Winn, B. [Quantum Condensed Matter Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States)

2013-06-15T23:59:59.000Z

3

E-Print Network 3.0 - air station usa Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and WALD, Lucien. Adding virtual measuring stations to a network for urban air pollution Summary: , and WALD, Lucien. Adding virtual measuring stations to a network for...

4

Resilient design of recharging station networks for electric transportation vehicles  

SciTech Connect (OSTI)

As societies shift to 'greener' means of transportation using electricity-driven vehicles one critical challenge we face is the creation of a robust and resilient infrastructure of recharging stations. A particular issue here is the optimal location of service stations. In this work, we consider the placement of battery replacing service station in a city network for which the normal traffic flow is known. For such known traffic flow, the service stations are placed such that the expected performance is maximized without changing the traffic flow. This is done for different scenarios in which roads, road junctions and service stations can fail with a given probability. To account for such failure probabilities, the previously developed facility interception model is extended. Results show that service station failures have a minimal impact on the performance following robust placement while road and road junction failures have larger impacts which are not mitigated easily by robust placement.

Kris Villez; Akshya Gupta; Venkat Venkatasubramanian

2011-08-01T23:59:59.000Z

5

Malm Hydrogen and CNG/Hydrogen filling station and Hythane bus project  

E-Print Network [OSTI]

cell vehicles. DaimlerChrysler Evobus has specified 350 bar as onboard storage for the hydrogen fuelChrysler FCell fuel cell cars and several other modern demonstration vehicles using hydrogen as fuel. · H2/CNG in the dispenser directly while filling the vehicle fuel tank. The different fuelling options at the dispenser are

6

Interweaving 3D Network with Double Helical Tubes Filled by 1D Coordination Polymer Chains  

E-Print Network [OSTI]

Interweaving 3D Network with Double Helical Tubes Filled by 1D Coordination Polymer Chains E Yang- tecture interpenetrated by three types of coordination polymer motifs. Two independent {[Cu2(mellitate)(4,4-bpy)(H2O)2]2- } 3D polymers incorporating helical substructures were interwoven into a 3D network

Gao, Song

7

Efficient energy based modeling and experimental validation of liquid filling in planar micro-fluidic components and networks  

E-Print Network [OSTI]

Efficient energy based modeling and experimental validation of liquid filling in planar micro-fluidic components and networks I. Treise, N. Fortner, B. Shapiro* and A. Hightower Received 25th June 2004, Accepted409680k This paper presents a model that describes how liquid flow fills micro-fluidic components

Shapiro, Benjamin

8

Rendezvous Design Algorithms for Wireless Sensor Networks with a Mobile Base Station  

E-Print Network [OSTI]

of controlled mobil- ity and in-network data caching and can achieve a desirable balance between network energy; Tian Wang; Weijia Jia; Minming Li Deptment of Computer Science, City University of Hong Kong 83 Tat that significant energy saving can be achieved in wireless sensor networks with a mobile base station that collects

9

Screening evaluation of radionuclide groundwater concentrations for the end state basement fill model Zion Nuclear Power Station decommissioning project  

SciTech Connect (OSTI)

ZionSolutions is in the process of decommissioning the Zion Nuclear Power Plant. The site contains two reactor Containment Buildings, a Fuel Building, an Auxiliary Building, and a Turbine Building that may be contaminated. The current decommissioning plan involves removing all above grade structures to a depth of 3 feet below grade. The remaining underground structures will be backfilled with clean material. The final selection of fill material has not been made.

Sullivan T.

2014-06-09T23:59:59.000Z

10

We use networks so that if one power station goes down, the area it provides  

E-Print Network [OSTI]

.cwh.org.uk/main.asp?page=393 ­ Battersea Power Station; www.progressillinois.com/.../images/windfarm.jpg - Wind farm; The Simpsons - nuclear power plant; http://www.projectsmonitor.com/NewsImages/ - Gas Pipeline. #12;We use networks so that if one power station goes down, the area it provides electricity

Wright, Francis

11

anna power station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

1 Regarding Kewaunee Power Station CiteSeer Summary: This supplemental environmental impact statement (SEIS) has been prepared in response to an application submitted by Dominion...

12

anna power stations: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

1 Regarding Kewaunee Power Station CiteSeer Summary: This supplemental environmental impact statement (SEIS) has been prepared in response to an application submitted by Dominion...

13

Network Formation Games Among Relay Stations in Next Generation Wireless Networks  

E-Print Network [OSTI]

The introduction of relay station (RS) nodes is a key feature in next generation wireless networks such as 3GPP's long term evolution advanced (LTE-Advanced), or the forthcoming IEEE 802.16j WiMAX standard. This paper presents, using game theory, a novel approach for the formation of the tree architecture that connects the RSs and their serving base station in the \\emph{uplink} of the next generation wireless multi-hop systems. Unlike existing literature which mainly focused on performance analysis, we propose a distributed algorithm for studying the \\emph{structure} and \\emph{dynamics} of the network. We formulate a network formation game among the RSs whereby each RS aims to maximize a cross-layer utility function that takes into account the benefit from cooperative transmission, in terms of reduced bit error rate, and the costs in terms of the delay due to multi-hop transmission. For forming the tree structure, a distributed myopic algorithm is devised. Using the proposed algorithm, each RS can individuall...

Saad, Walid; Ba?ar, Tamer; Debbah, Mérouane; Hjørungnes, Are

2012-01-01T23:59:59.000Z

14

Analysis on Current Status of the Gas Filling Station Networks Website |  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector GeneralDepartmentAUDIT REPORTOpenWende NewSowitecAWSAgri-EnergyAmbeneExisting WindoperationsOpen

15

antarctic station casey: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

SOAP for setting up the tetheredsonde All of the Costa Rica REU groups for data 148 OF CAR SHARING STATIONS CiteSeer Summary: Approximately half of the worlds population is...

16

Implementing a wireless base station for a sensor network  

E-Print Network [OSTI]

Using wireless sensor networks for monitoring infrastructure is a new trend in civil engineering. Compared with traditional ways to monitor infrastructure, wireless sensor networks are cheap, safe, and compact. However, ...

Song, Heewon, 1977-

2004-01-01T23:59:59.000Z

17

Lambda Station: Alternate network path forwarding for production SciDAC applications  

SciTech Connect (OSTI)

The LHC era will start very soon, creating immense data volumes capable of demanding allocation of an entire network circuit for task-driven applications. Circuit-based alternate network paths are one solution to meeting the LHC high bandwidth network requirements. The Lambda Station project is aimed at addressing growing requirements for dynamic allocation of alternate network paths. Lambda Station facilitates the rerouting of designated traffic through site LAN infrastructure onto so-called 'high-impact' wide-area networks. The prototype Lambda Station developed with Service Oriented Architecture (SOA) approach in mind will be presented. Lambda Station has been successfully integrated into the production version of the Storage Resource Manager (SRM), and deployed at US CMS Tier1 center at Fermilab, as well as at US-CMS Tier-2 site at Caltech. This paper will discuss experiences using the prototype system with production SciDAC applications for data movement between Fermilab and Caltech. The architecture and design principles of the production version Lambda Station software, currently being implemented as Java based web services, will also be presented in this paper.

Grigoriev, Maxim; Bobyshev, Andrey; Crawford, Matt; DeMar, Phil; Grigaliunas, Vyto; Moibenko, Alexander; Petravick, Don; /Fermilab; Newman, Harvey; Steenberg, Conrad; Thomas, Michael; /Caltech

2007-09-01T23:59:59.000Z

18

E-Print Network 3.0 - amyloid water-filled nanotubes Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

water-filled nanotubes Search Powered by Explorit Topic List Advanced Search Sample search results for: amyloid water-filled nanotubes Page: << < 1 2 3 4 5 > >> 1 Author's personal...

19

A collaborative network middleware project by Lambda Station, TeraPaths, and Phoebus  

SciTech Connect (OSTI)

The TeraPaths, Lambda Station, and Phoebus projects, funded by the US Department of Energy, have successfully developed network middleware services that establish on-demand and manage true end-to-end, Quality-of-Service (QoS) aware, virtual network paths across multiple administrative network domains, select network paths and gracefully reroute traffic over these dynamic paths, and streamline traffic between packet and circuit networks using transparent gateways. These services improve network QoS and performance for applications, playing a critical role in the effective use of emerging dynamic circuit network services. They provide interfaces to applications, such as dCache SRM, translate network service requests into network device configurations, and coordinate with each other to setup up end-to-end network paths. The End Site Control Plane Subsystem (ESCPS) builds upon the success of the three projects by combining their individual capabilities into the next generation of network middleware. ESCPS addresses challenges such as cross-domain control plane signalling and interoperability, authentication and authorization in a Grid environment, topology discovery, and dynamic status tracking. The new network middleware will take full advantage of the perfSONAR monitoring infrastructure and the Inter-Domain Control plane efforts and will be deployed and fully vetted in the Large Hadron Collider data movement environment.

Bobyshev, A.; /Fermilab; Bradley, S.; /Brookhaven; Crawford, M.; /Fermilab; DeMar, P.; /Fermilab; Katramatos, D.; /Brookhaven; Shroff, K.; /Brookhaven; Swany, M.; /Delaware U.; Yu, D.; /Brookhaven

2010-01-01T23:59:59.000Z

20

Solid-liquid composite structures: elastic beams with embedded liquid-filled parallel-channel networks  

E-Print Network [OSTI]

Deformation due to embedded fluidic networks is currently studied in the context of soft-actuators and soft-robotics. Expanding on this concept, beams can be designed so that the pressure in the channel-network is created directly from external forces acting on the beam, and thus can be viewed as passive solid-liquid composite structure. We obtain a continuous function relating the network geometry to the deformation. This enables design of networks creating arbitrary steady and time varying deformation-fields as well as to eliminate deformation created by external forces.

Yoav Matia; Amir Gat

2014-09-07T23:59:59.000Z

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

E-Print Network 3.0 - arctowski station king Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

HoytSt Burnett... Front Stadium Broad St Station Military Park Rutgers University Essex County College PASSAIC RIVER BROAD ST... STATION Route 280 Pennsylvania RailroadStation...

22

Detailed Analysis of Urban Station Siting for California Hydrogen Highway Network  

E-Print Network [OSTI]

www.energy.ca.gov/gasoline/gasoline_stations/index.html.estimates range from 10% of existing gasoline stations to30% of gasoline stations. Two of the studies[7,8] further

Nicholas, Michael A; Ogden, Joan M

2007-01-01T23:59:59.000Z

23

The AmeriFlux Network of Long-Term CO{sub 2} Flux Measurement Stations: Methodology and Intercomparability  

SciTech Connect (OSTI)

A portable flux measurement system has been used within the AmeriFlux network of CO{sub 2} flux measurement stations to enhance the comparability of data collected across the network. No systematic biases were observed in a comparison between portable system and site H, LE, or CO{sub 2} flux values although there were biases observed between the portable system and site measurement of air temperature and PPFD. Analysis suggests that if values from two stations differ by greater than 26% for H, 35% for LE, and 32% for CO{sub 2} flux they are likely to be significant. Methods for improving the intercomparability of the network are also discussed.

Hollinger, D. Y.; Evans, R. S.

2003-05-20T23:59:59.000Z

24

E-Print Network 3.0 - alternative fueling station Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

plan for 1,000 stations and 2 million FECVs by 2025... continues to grow at a rapid pace. Germany, Japan, and Korea anticipate having over 300 fueling stations... the mass...

25

E-Print Network 3.0 - air station north Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Refueling Station... . Irvine North ... Source: California Energy Commission Collection: Energy Storage, Conversion and Utilization 3 INTERNATIONAL JOURNAL OF CLIMATOLOGY, VOL....

26

Toxicity assessment of water and sediment elutriates from fixed-station ambient water quality network stations, 1986, 1987, 1988, and 1989  

SciTech Connect (OSTI)

Toxicity biomonitoring of water column and sediment toxicity was conducted at six fixed network stations from 1986 through 1989. Stations were located on the Holston River, Bear Creek (Pickwick Reservoir), Hiwassee River, Emory River, Nolichucky River, and French Broad River at locations chosen to represent those sub-basins. Tests evaluated acute and chronic responses of larval fathead minnow survival and growth and Ceriodaphnia survival and reproduction to water and sediment elutriates collected from these sites. Samples were collected once each year during summer. Neither water nor sediment elutriates from the French Broad River were toxic during the study period. Water column toxicity (chronic) occurred in Bear Creek in 1986 and in the Nolichucky River in 1987. Sediment elutriate toxicity occurred once during the study period in the Emory (1987) and Nolichucky (1988) Rivers. Sediments from the Holston and Hiwassee Rivers were toxic two times each. Hiwassee River sediment exhibited >1.3 chronic toxicity units in 1987 and 1989 (were toxic at the lowest dilution tested). Holston River sediment toxicity occurred during the most recent two years of testing. Results from the Holston and Hiwassee Rivers may indicate a toxics problem in the sub-basin. No acute toxicity occurred during the study. 4 refs., 2 tabs.

Moses, J.; Wade, D.C.

1991-02-01T23:59:59.000Z

27

E-Print Network 3.0 - air station project Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Collection: Energy Storage, Conversion and Utilization ; Renewable Energy 28 www.praxair.com H2 Storage and Summary: Station Schedule Overview Project Milestones Planned...

28

E-Print Network 3.0 - air station cape Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Geosciences ; Environmental Sciences and Ecology 32 ForPeerReview PUBLIC ACCEPTANCE OF OFFSHORE WIND POWER Summary: Service (MMS) 12. The Mirant Canal Station power plant,...

29

E-Print Network 3.0 - anaheim police station Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Annual William O. Lipinski Symposium on Transportation Policy Summary: Water and wastewater treatment facilities Police and fire stations StreetlightsPolice and fire......

30

BEAULANT, Anne-Lise, PERRON, Gilles, KLEINPETER, Joseph, WEBER, Christiane, RANCHIN, Thierry, and WALD, Lucien. Adding virtual measuring stations to a network for urban air pollution  

E-Print Network [OSTI]

, and WALD, Lucien. Adding virtual measuring stations to a network for urban air pollution mapping TO A NETWORK FOR URBAN AIR POLLUTION MAPPING A. L. Beaulant1* , G. Perron2 , J. Kleinpeter2 , C. Weber3 , T la Pollution atmosphérique en Alsace), 5 rue de Madrid, 67300 Schiltigheim, France 3 Laboratoire

Paris-Sud XI, Université de

31

audio-magnetotelluric station location: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

of Chicago ATLAS HEP, Enrico Fermi Institute 5640 S. Ellis Ave Chicago, IL 60637 October 15, 2007 Abstract A remote monitoring station located at the University of Chicago is...

32

E-Print Network 3.0 - asymmetric relay station Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Mengesha, Holger Karl Summary: -hoc relaying technology. In their paper, they showed how Ad-hoc relay stations can relay traffic from one cell... Relay Routing and Scheduling for...

33

E-Print Network 3.0 - angle-scanning photoemission end-station...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

for: angle-scanning photoemission end-station Page: << < 1 2 3 4 5 > >> 1 SRI 2007 Conference Proceedings Title: Optimization of the 3m TGM beamline, at CAMD, for constant...

34

The Fuel-Travel-Back Approach to Hydrogen Station Siting  

E-Print Network [OSTI]

the experience of gasoline stations. Driven by the notion "percentages of existing gasoline stations, for a successfulsubset of the existing gasoline station network [14]. These

Lin, Zhenhong; Ogden, Joan; Fan, Yueyue; Chen, Chien-Wei

2009-01-01T23:59:59.000Z

35

A Flow Level Perspective on Base Station Power Allocation in Green Networks  

E-Print Network [OSTI]

the energy-efficiency of base stations operating in the downlink. The energy-efficiency refers to the amount nature of users (referred to as the global energy-efficiency). We emphasize our numerical results that study the influence of the radio conditions, transmit power and the user traffic on the energy-efficiency

Boyer, Edmond

36

ETM (Distribution Network Automation on 10 kV cable line stations...  

Open Energy Info (EERE)

will be equipped by RTUs, to provide remote observability and remote control. The communication (connection) is established via GSM network. References "EU Smart Grid...

37

Natural Gas Compressor Stations on the Interstate Pipeline Network: Developments Since 1996  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia,(Million Barrels) Crude Oil Reserves in Nonproducing Reservoirs Year2per6.48 6.18 5.63 4.73Feet)Compressor Stations

38

Comparison of Idealized and Real-World City Station Citing Models for Hydrogen Distribution  

E-Print Network [OSTI]

city size, and gasoline station locations. By characterizingfuel than typical gasoline stations. As a result, it will bestreet networks and gasoline stations for (a) Sacramento (b)

Yang, Christopher; Nicholas, Michael A; Ogden, Joan M

2006-01-01T23:59:59.000Z

39

Refueling Availability for Alternative Fuel Vehicle Markets: Sufficient Urban Station Coverage  

E-Print Network [OSTI]

ed Basin Dataset on Urban Gasoline Stations. Institute ofavailability Gasoline stations abstract Alternative fueldistribution, the existing gasoline station networks in many

Melaina, Marc W; Bremson, Joel

2008-01-01T23:59:59.000Z

40

Particle-filled microporous materials  

DOE Patents [OSTI]

A microporous particulate-filled thermoplastic polymeric article is provided. The article can be in the form of a film, a fiber, or a tube. The article has a thermoplastic polymeric structure having a plurality of interconnected passageways to provide a network of communicating pores. The microporous structure contains discrete submicron or low micron-sized particulate filler, the particulate filler being substantially non-agglomerated. 3 figs.

McAllister, J.W.; Kinzer, K.E.; Mrozinski, J.S.; Johnson, E.J.; Dyrud, J.F.

1990-09-18T23:59:59.000Z

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Computational Optimization of Gas Compressor Stations: MINLP ...  

E-Print Network [OSTI]

Feb 26, 2015 ... Abstract: When considering cost-optimal operation of gas transport networks, compressor stations play the most important role. Proper ...

Daniel Rose

2015-02-26T23:59:59.000Z

42

EUHYFIS Hydrogen Filling Station Consortium | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision has beenFfe2fb55-352f-473b-a2dd-50ae8b27f0a6 No revision hasESE Alcohol Jump to: navigation,ESolarEUHYFIS

43

The CNGS Target Station Presented by L.Bruno  

E-Print Network [OSTI]

sealed system filled with 0.5 bar of He. The tube has annular fins to enhance convective heat transfer enclosure Inlet target Inlet fixed shielding Outlet Beam #12;The target Assembly The CNGS Target Station as

McDonald, Kirk

44

Gas filled panel insulation  

DOE Patents [OSTI]

A structural or flexible highly insulative panel which may be translucent, is formed from multi-layer polymeric material in the form of an envelope surrounding a baffle. The baffle is designed so as to minimize heat transfer across the panel, by using material which forms substantially closed spaces to suppress convection of the low conductivity gas fill. At least a portion of the baffle carries a low emissivity surface for suppression of infrared radiation. 18 figures.

Griffith, B.T.; Arasteh, D.K.; Selkowitz, S.E.

1993-12-14T23:59:59.000Z

45

Dye filled security seal  

DOE Patents [OSTI]

A security seal for providing an indication of unauthorized access to a sealed object includes an elongate member to be entwined in the object such that access is denied unless the member is removed. The elongate member has a hollow, pressurizable chamber extending throughout its length that is filled with a permanent dye under greater than atmospheric pressure. Attempts to cut the member and weld it together are revealed when dye flows through a rupture in the chamber wall and stains the outside surface of the member.

Wilson, Dennis C. W. (Tijeras, NM)

1982-04-27T23:59:59.000Z

46

Enhancing the energy efficiency of radio base stations   

E-Print Network [OSTI]

This thesis is concerned with the energy efficiency of cellular networks. It studies the dominant power consumer in future cellular networks, the Long Term Evolution (LTE) radio Base Station (BS), and proposes mechanisms ...

Holtkamp, Hauke Andreas

2014-06-30T23:59:59.000Z

47

Solar and Infrared Radiation Station (SIRS) Handbook  

SciTech Connect (OSTI)

The Solar Infrared Radiation Station (SIRS) provides continuous measurements of broadband shortwave (solar) and longwave (atmospheric or infrared) irradiances for downwelling and upwelling components. The following six irradiance measurements are collected from a network of stations to help determine the total radiative flux exchange within the Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) Climate Research Facility: • Direct normal shortwave (solar beam) • Diffuse horizontal shortwave (sky) • Global horizontal shortwave (total hemispheric) • Upwelling shortwave (reflected) • Downwelling longwave (atmospheric infrared) • Upwelling longwave (surface infrared)

Stoffel, T

2005-07-01T23:59:59.000Z

48

SOUTH STATION TAmtrak, Commuter  

E-Print Network [OSTI]

SOUTH STATION TAmtrak, Commuter Rail, Bus Station, MBTA Red Line Knapp St. Kneeland St. Stuart St) T BOYLSTON (MBTA Green Line) T NEW ENGLAND MEDICAL CENTER (MBTA Orange Line) Boston Campus Accessibility Map

Dennett, Daniel

49

New Paradigm for Seismic Networks: Crowd-Sourced Seismic Networks,  

E-Print Network [OSTI]

#12;New Paradigm for Seismic Networks: Crowd-Sourced Seismic Networks, including Buildings Tom Egill Hauksson #12;SCSN: what does it encompass? · ~360 Seismic Stations · ~60 stations from partners SCSN/SCEDC total of ~26 FTE's #12;Crowd Sourced Networks · Current broadband seismic network

Greer, Julia R.

50

Gas Filled Detectors counting & tracking of  

E-Print Network [OSTI]

Gas Filled Detectors counting & tracking of particles energy loss generation of electron-ion+ pairs #12;Gas Filled Detectors Primary and Total Ionization fast charged particles ionize the atoms of a gas fraction of resulting primary electrons have enough kinetic energy to ionize other atoms #12;Gas Filled

Peletier, Reynier

51

Financial Networks Anna Nagurney  

E-Print Network [OSTI]

themselves, such as the Internet with electric power networks, financial networks, and transportation Automobiles, Trains, and Planes, Manufacturing and logistics Workstations, Distribution Points Processing Cables Radio Links Voice, Data, Video Energy Pumping Stations, Plants Pipelines, Transmission Lines Water

Nagurney, Anna

52

Blodgett Forest Research Station  

E-Print Network [OSTI]

kilometres away. Then, as the sun reaches its peak in the sky, pollution from California's Central Valley a crucial part in the chemistry of aerosol particles and with pollutants such as ozone. His discoveries may help to fill in con- founding gaps in atmospheric science, such as how VOCs from plants affect air

Wildermuth, Mary C

53

M Station, Austin  

E-Print Network [OSTI]

SUNSHINE MATHON, M. Arch., LEED Homes AP Design + Development Director sunshine.mathon@foundcom.org FOUNDATION COMMUNITIES Austin, TX T.O.D. District Area T.O.D. District Area T.O.D. District Area T.O.D. District Area 8.5 ACRE SITE 5-1.../2 Acres Buildable Boggy Creek Floodplain 8.5 ACRE SITE 5-1/2 Acres Buildable Boggy Creek Floodplain 4 Acres Concrete Abandoned Grayfield M STATION 80% 2 & 3-Bedrooms 150 1,2 & 3-Bedroom Apts M STATION 80% 2 & 3-Bedrooms 150 1,2 & 3-Bedroom Apts...

Mathon, S.

2011-01-01T23:59:59.000Z

54

A computer program for HVDC converter station RF noise calculations  

SciTech Connect (OSTI)

HVDC converter station operations generate radio frequency (RF) electromagnetic (EM) noise which could interfere with adjacent communication and computer equipment, and carrier system operations. A generic Radio Frequency Computer Analysis Program (RAFCAP) for calculating the EM noise generated by valve ignition of a converter station has been developed as part of a larger project. The program calculates RF voltages, currents, complex power, ground level electric field strength and magnetic flux density in and around an HVDC converter station. The program requires the converter station network to be represented by frequency dependent impedance functions. Comparisons of calculated and measured values are given for an actual HVDC station to illustrate the validity of the program. RAFCAP is designed to be used by engineers for the purpose of calculating the RF noise produced by the igniting of HVDC converter valves.

Kasten, D.G.; Caldecott, R.; Sebo, S.A. (Ohio State Univ., Columbus, OH (United States). Dept. of Electrical Engineering); Liu, Y. (Virginia Polytechnic Inst. State Univ., Blacksburg, VA (United States). Bradley Dept. of Electrical Engineering)

1994-04-01T23:59:59.000Z

55

Skate Station UF Services  

E-Print Network [OSTI]

friends, practice your English, and try new activities! Where: Skate Station Funworks We will be meeting and more orderly manner. Everyone will be served eventually. Fire Drills/Alarms: Whenever you hear a fire should park your bike in well-lighted areas and lock it up when you park it. The best lock is a U

Pilyugin, Sergei S.

56

Buried waste integrated demonstration human engineered control station. Final report  

SciTech Connect (OSTI)

This document describes the Human Engineered Control Station (HECS) project activities including the conceptual designs. The purpose of the HECS is to enhance the effectiveness and efficiency of remote retrieval by providing an integrated remote control station. The HECS integrates human capabilities, limitations, and expectations into the design to reduce the potential for human error, provides an easy system to learn and operate, provides an increased productivity, and reduces the ultimate investment in training. The overall HECS consists of the technology interface stations, supporting engineering aids, platform (trailer), communications network (broadband system), and collision avoidance system.

Not Available

1994-09-01T23:59:59.000Z

57

Market Assessment and Demonstration of Lignite FBC Ash Flowable Fill Applications  

SciTech Connect (OSTI)

Montana-Dakota Utilities (MDU) and Western Research Institute (WRI) have been developing flowable fill materials formulated using ash from the Montana-Dakota Utilities R. M. Heskett Station in Mandan, North Dakota. MDU and WRI have partnered with the U.S. Department of Energy (DOE) and the North Dakota Industrial Commission (NDIC) to further the development of these materials for lignite-fired fluidized-bed combustion (FBC) facilities. The MDU controlled density fill (CDF) appears to be a viable engineering material and environmentally safe. WRI is pursuing the commercialization of the technology under the trademark Ready-Fill{trademark}. The project objectives were to: (1) assess the market in the Bismarck-Mandan area; (2) evaluate the geotechnical properties and environmental compatibility; and (3) construct and monitor demonstrations of the various grades of flowable fill products in full-scale demonstrations. The scope of initial phase of work entailed the following: Task I--Assess Market for MDU Flowable Fill Products; Task II--Assess Geotechnical and Environmental Properties of MDU Flowable Fill Products; and Task III--Demonstrate and Monitor MDU Flowable Fill Products in Field-Scale Demonstrations. The results of these testing and demonstration activities proved the following: (1) The market assessment indicated that a market exists in the Bismarck-Mandan area for structural construction applications, such as sub-bases for residential and commercial businesses, and excavatable fill applications, such as gas line and utility trench filling. (2) The cost of the MDU flowable fill product must be lower than the current $35-$45/cubic yard price if it is to become a common construction material. Formulations using MDU ash and lower-cost sand alternatives offer that opportunity. An estimated market of 10,000 cubic yards of MDU flowable fill products could be realized if prices could be made competitive. (3) The geotechnical properties of the MDU ash-based flowable fill can be modified to meet the needs of a range of applications from structural fill applications to excavatable applications, such as utility trench fill. (4) Environmental assessments using standard testing indicate that the environmental properties of the fill materials are compatible with numerous construction applications and do not pose a threat to either adjacent groundwater or soils. (5) WRI developed an Environmental Field Simulator (EFS) method for assessing the impact of flowable fill materials on adjacent soils and found that the zone of impact is less than a couple of inches, thereby posing no threat to adjacent soils. (6) Field-scale demonstrations of the MDU flowable fill were constructed and were successful for structural, as well as excavatable applications. Monitoring has demonstrated the geotechnical performance, environmental performance, and compatibility with common embed materials with the MDU flowable fill products. Technical and economic issues were identified that may hinder the commercial acceptance of MDU flowable fill materials, including: (1) the ability to produce a consistent product; (2) the ability to provide a product year round (cold weather retards strength development); and (3) the ability to evaluate and produce commercial quantities of MDU flowable fill using inexpensive materials.

Alan E. Bland

2003-09-30T23:59:59.000Z

58

Pacific Southwest Research Station Publications  

E-Print Network [OSTI]

Bulletins 1- 28 1965-1989 Soil- Vegetation Tables -- 1965-1980 Solar Irradiation and Shadow Length Tables-1971 1938 California Forest and Range Experiment Station Annual Report 1939 California Forest and Range Experiment Station Annual Report 1940 California Forest and Range Experiment Station Annual Report 1951

Standiford, Richard B.

59

Fill in the following information: Mediation Training  

E-Print Network [OSTI]

Fill in the following information: Mediation Training Fall 2014 Registration Form GENERAL / CIVIL:30 pm) Select training date(s): 3 1 2 Mail check or money order to: J.W. Fanning Institute

Arnold, Jonathan

60

Dredged and Fill Material Disposal (North Dakota)  

Broader source: Energy.gov [DOE]

This chapter provides regulations for the disposal of dredged and fill material. Any entity desiring to dispose of such material must first obtain a permit, and the State Engineer has the...

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Memory through re-use : food, fuel, fossils, filth and a few filling stations  

E-Print Network [OSTI]

This project engages disposable objects and concepts in the design process. Cultural items deemed unusable, obsolete, unfashionable, repugnant, toxic, or otherwise dirty are used as a resource and as a means to access ...

Kron, Zachary M., 1972-

2001-01-01T23:59:59.000Z

62

Optimal Charging of Electric Vehicles in Smart Grid: Characterization and Valley-Filling Algorithms  

E-Print Network [OSTI]

Optimal Charging of Electric Vehicles in Smart Grid: Characterization and Valley-Filling Algorithms with different EV battery charging rate constraints, that is distributed across a smart power grid network the power grid. One way to tackle this problem is to adopt a "smart grid" solution, which allows EVs

Tan, Chee Wei

63

Transit Infrastructure Finance Through Station Location Auctions  

E-Print Network [OSTI]

Numerous route and station options Strong real estate marketreal estate market Transit friendly constituents Numerous route and station options

Ian Carlton

2009-01-01T23:59:59.000Z

64

Station GPS permanente IPG Paris DGF Uchile UNAP Iquique  

E-Print Network [OSTI]

NetRS, Antenna TRIMBLE Zephyr geodetic and autonomous energy (battery and solar panel). HISTORIC Semi.71476292 - 69.82727839 1675.36 DESCRIPTION North Chile II region, semi-permanent GPS station IPGP / DGF network American but in the convergence area of Nazca/ SOAM plates. Approximate Position X coordinate (m) : 2044899

Vigny, Christophe

65

Multifunctional, Inorganic-Filled Separators for Large Format...  

Broader source: Energy.gov (indexed) [DOE]

& Publications Multifunctional, Inorganic-Filled Separators for Large Format, Li-ion Batteries Multifunctional, Inorganic-Filled Separators for Large Format, Li-ion Batteries...

66

Multifunctional, Inorganic-Filled Separators for Large Format...  

Broader source: Energy.gov (indexed) [DOE]

Multifunctional, Inorganic-Filled Separators for Large Format, Li-ion Batteries Multifunctional, Inorganic-Filled Separators for Large Format, Li-ion Batteries 2012 DOE Hydrogen...

67

DOE to Resume Filling Strategic Petroleum Reserve: Oil Acquisition...  

Energy Savers [EERE]

to Resume Filling Strategic Petroleum Reserve: Oil Acquisition Slated for 2009 DOE to Resume Filling Strategic Petroleum Reserve: Oil Acquisition Slated for 2009 January 2, 2009 -...

68

Filling the Strategic Petroleum Reserve | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Strategic Petroleum Reserve Filling the Strategic Petroleum Reserve Filling the Strategic Petroleum Reserve Established in 1975 in the aftermath of the OPEC oil embargo, the...

69

Diary 16 -24 September 2013 A bonus week at the Zackenberg station  

E-Print Network [OSTI]

their parade towards the showers in building 9. However, there was no severe water shortage at this time restricted water usage. The water level in the river falls and night temperatures drop below zero creating ice. This hinders the water intake from the river to fill up the fresh water reservoirs at the station

70

Network Economics Anna Nagurney  

E-Print Network [OSTI]

Cables Radio Links Voice, Data, Video Energy Pumping Stations, Plants Pipelines, Transmission Lines Water building evacuation models · DNA sequence alignment · assembly line balancing · compact book storage Network Satellite and Undersea Cable Networks Duke Energy Gas Pipeline Network Transportation

Nagurney, Anna

71

Geographic Trough Filling for Internet Datacenters  

E-Print Network [OSTI]

To reduce datacenter energy consumption and cost, current practice has considered demand-proportional resource provisioning schemes, where servers are turned on/off according to the load of requests. Most existing work considers instantaneous (Internet) requests only, which are explicitly or implicitly assumed to be delay-sensitive. On the other hand, in datacenters, there exist a vast amount of delay-tolerant jobs, such as background/maintainance jobs. In this paper, we explicitly differentiate delay-sensitive jobs and delay tolerant jobs. We focus on the problem of using delay-tolerant jobs to fill the extra capacity of datacenters, referred to as trough/valley filling. Giving a higher priority to delay-sensitive jobs, our schemes complement to most existing demand-proportional resource provisioning schemes. Our goal is to design intelligent trough filling mechanisms that are energy efficient and also achieve good delay performance. Specifically, we propose two joint dynamic speed scaling and traffic shifti...

Xu, Dan

2011-01-01T23:59:59.000Z

72

Going to Work: Filling Out an Application  

E-Print Network [OSTI]

Edited by Rosemarie Hoffman Assistant Professor and Extension Individual and Family Development Specialist, The Texas A&M University System L-2366 12-99 Filling out an Application W hen looking for a job, you will have to fill out many different job.... or # Number Below are explanations of words you may see on application forms: Applicant: This means YOU, the per- son who is applying for the job. Marital status: Are you married, or single? Spouse: Your wife or husband?s name. Dependents: The number of people...

Hoffman, Rosemarie

2000-01-07T23:59:59.000Z

73

Alkaline earth filled nickel skutterudite antimonide thermoelectrics  

DOE Patents [OSTI]

A thermoelectric material including a body centered cubic filled skutterudite having the formula A.sub.xFe.sub.yNi.sub.zSb.sub.12, where A is an alkaline earth element, x is no more than approximately 1.0, and the sum of y and z is approximately equal to 4.0. The alkaline earth element includes guest atoms selected from the group consisting of Be, Mb, Ca, Sr, Ba, Ra and combinations thereof. The filled skutterudite is shown to have properties suitable for a wide variety of thermoelectric applications.

Singh, David Joseph

2013-07-16T23:59:59.000Z

74

Wachs Cutter Tooling Station (4495)  

Broader source: Energy.gov (indexed) [DOE]

purchase, build and install Wachs cutter tooling. The Wachs Cutter Tooling Station is similar to previously operated facility tooling and will utilize an existing hydraulic unit....

75

Station design using orifice meters  

SciTech Connect (OSTI)

This paper reports that proper meter station design using gas orifice meters must include consideration of a number of factors to minimize operation and maintenance problems while obtaining the best accuracy over the life of the station. A station should provide accuracy, be safe, functional, economical and free of undue maintenance. It should comply with all codes, reports and specifications but most of all it should be able to comply with terms set forth in the contract. All measuring stations should be designed with considerations of growth or reductions in volume. It should be attractive and built to last for many years.

Upp, E.L. (Daniel Industries, Inc., Houston, TX (United States))

1992-07-01T23:59:59.000Z

76

Fuel Station Procedure Applicability All  

E-Print Network [OSTI]

Fuel Station Procedure Applicability All Last Revised 11/20/12 Procedure Owner Andrew Grant agrant for the purchasing and distribution of fuel for vehicles owned by Bowling Green State University (BGSU). This centralization is important to ensure compliance for BGSU employees who use the centralized fuel station and fuel

Moore, Paul A.

77

amalgam fillings associations: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

a table of plasma parameters from C-Mod shots and to plot data from features are: FILLDB: utility to populate plasma data into a database table 1. User defines two simple,...

78

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

4-12: Hydrogen Cost Comparison for Electrolysis Station Withthe hydrogen costs from the HSCM for electrolysis stations

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

79

COMSOL MULTIPHYSICS MODEL FOR DWPF CANISTER FILLING  

SciTech Connect (OSTI)

The purpose of this work was to develop a model that can be used to predict temperatures of the glass in the Defense Waste Processing Facility (DWPF) canisters during filling and cooldown. Past attempts to model these processes resulted in large (>200K) differences in predicted temperatures compared to experimentally measured temperatures. This work was therefore intended to also generate a model capable of reproducing the experimentally measured trends of the glass/canister temperature during filling and subsequent cooldown of DWPF canisters. To accomplish this, a simplified model was created using the finite element modeling software COMSOL Multiphysics which accepts user defined constants or expressions to describe material properties. The model results were compared to existing experimental data for validation. A COMSOL Multiphysics model was developed to predict temperatures of the glass within DWPF canisters during filling and cooldown. The model simulations and experimental data were in good agreement. The largest temperature deviations were {approx}40 C for the 87inch thermocouple location at 3000 minutes and during the initial cooldown at the 51 inch location occurring at approximately 600 minutes. Additionally, the model described in this report predicts the general trends in temperatures during filling and cooling observed experimentally. However, the model was developed using parameters designed to fit a single set of experimental data. Therefore, Q-loss is not currently a function of pour rate and pour temperature. Future work utilizing the existing model should include modifying the Q-loss term to be variable based on flow rate and pour temperature. Further enhancements could include eliminating the Q-loss term for a user defined convection where Navier-Stokes does not need to be solved in order to have convection heat transfer.

Kesterson, M.

2011-03-31T23:59:59.000Z

80

Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation Desert Southwest Regionat Cornell Batteries &NSTCurrent Issues &Network » Network

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network [OSTI]

Costs Annualized Investment Cost, 1000$/yr Total AnnualizedH2 Fueling Stations Investment Cost Cost ($/yr) OperatingH2 Fueling Stations Investment Cost Cost ($/kg) Operating

Weinert, Jonathan X.; Shaojun, Liu; Ogden, J; Jianxin, Ma

2006-01-01T23:59:59.000Z

82

Energy Department Launches Alternative Fueling Station Locator...  

Broader source: Energy.gov (indexed) [DOE]

Launches Alternative Fueling Station Locator App Energy Department Launches Alternative Fueling Station Locator App November 7, 2013 - 11:16am Addthis As part of the Obama...

83

Request to Fill for Support Staff Position Vacancy  

E-Print Network [OSTI]

Request to Fill for Support Staff Position Vacancy The position described below is: New [ ] Revised of positions to be filled _________ This position vacancy is externally funded [ ] Shift work or special by _____________________________________________ Date ________________________ Director, Budget Administration [ ] Vacancy Management approval required

Martin, Jeff

84

Filling an emulsion drop with motile bacteria  

E-Print Network [OSTI]

We have measured the spatial distribution of motile Escherichia coli inside spherical water droplets emulsified in oil. At low cell concentrations, the cell density peaks at the water-oil interface; at increasing concentration, the bulk of each droplet fills up uniformly while the surface peak remains. Simulations and theory show that the bulk density results from a `traffic' of cells leaving the surface layer, increasingly due to cell-cell scattering as the surface coverage rises above $\\sim 10\\%$. Our findings show similarities with the physics of a rarefied gas in a spherical cavity with attractive walls.

I. D. Vladescu; E. J. Marsden; J. Schwarz-Linek; V. A. Martinez; J. Arlt; A. N. Morozov; D. Marenduzzo; M. E. Cates; W. C. K. Poon

2014-07-25T23:59:59.000Z

85

Optimal design of AC filter circuits in HVDC converter stations  

SciTech Connect (OSTI)

This paper investigates the reactive power as well as the harmonic conditions on both the valve and the AC-network sides of a HVDC converter station. The effect of the AC filter circuits is accurately modeled. The program is then augmented by adding an optimization routine. It can identify the optimal filter configuration, yielding the minimum current distortion factor at the AC network terminals for a prespecified fundamental reactive power to be provided by the filter. Several parameter studies were also conducted to illustrate the effect of accidental or intentional deletion of one of the filter branches.

Saied, M.M.; Khader, S.A. [Kuwait Univ. (Kuwait). Electrical and Computer Engineering Dept.

1995-12-31T23:59:59.000Z

86

Technical Analysis of the Hydrogen Energy Station Concept, Phase I and Phase II  

SciTech Connect (OSTI)

Phase I Due to the growing interest in establishing a domestic hydrogen infrastructure, several hydrogen fueling stations already have been established around the country as demonstration units. While these stations help build familiarity with hydrogen fuel in their respective communities, hydrogen vehicles are still several years from mass production. This limited number of hydrogen vehicles translates to a limited demand for hydrogen fuel, a significant hurdle for the near-term establishment of commercially viable hydrogen fueling stations. By incorporating a fuel cell and cogeneration system with a hydrogen fueling station, the resulting energy station can compensate for low hydrogen demand by providing both hydrogen dispensing and combined heat and power (CHP) generation. The electrical power generated by the energy station can be fed back into the power grid or a nearby facility, which in turn helps offset station costs. Hydrogen production capacity not used by vehicles can be used to support building heat and power loads. In this way, an energy station can experience greater station utility while more rapidly recovering capital costs, providing an increased market potential relative to a hydrogen fueling station. At an energy station, hydrogen is generated on-site. Part of the hydrogen is used for vehicle refueling and part of the hydrogen is consumed by a fuel cell. As the fuel cell generates electricity and sends it to the power grid, excess heat is reclaimed through a cogeneration system for use in a nearby facility. Both the electrical generation and heat reclamation serve to offset the cost of purchasing the equivalent amount of energy for nearby facilities and the energy station itself. This two-phase project assessed the costs and feasibility of developing a hydrogen vehicle fueling station in conjunction with electricity and cogenerative heat generation for nearby Federal buildings. In order to determine which system configurations and operational patterns would be most viable for an energy station, TIAX developed several criteria for selecting a representative set of technology configurations. TIAX applied these criteria to all possible technology configurations to determine an optimized set for further analysis, as shown in Table ES-1. This analysis also considered potential energy station operational scenarios and their impact upon hydrogen and power production. For example, an energy station with a 50-kWe reformer could generate enough hydrogen to serve up to 12 vehicles/day (at 5 kg/fill) or generate up to 1,200 kWh/day, as shown in Figure ES-1. Buildings that would be well suited for an energy station would utilize both the thermal and electrical output of the station. Optimizing the generation and utilization of thermal energy, hydrogen, and electricity requires a detailed look at the energy transfer within the energy station and the transfer between the station and nearby facilities. TIAX selected the Baseline configuration given in Table ES-1 for an initial analysis of the energy and mass transfer expected from an operating energy station. Phase II The purpose of this technical analysis was to analyze the development of a hydrogen-dispensing infrastructure for transportation applications through the installation of a 50-75 kW stationary fuel cell-based energy station at federal building sites. The various scenarios, costs, designs and impacts of such a station were quantified for a hypothetical cost-shared program that utilizes a natural gas reformer to provide hydrogen fuel for both the stack(s) and a limited number of fuel cell powered vehicles, with the possibility of using cogeneration to support the building heat load.

TIAX, LLC

2005-05-04T23:59:59.000Z

87

Daily snow depth measurements from 195 stations in the United States  

SciTech Connect (OSTI)

This document describes a database containing daily measurements of snow depth at 195 National Weather Service (NWS) first-order climatological stations in the United States. The data have been assembled and made available by the National Climatic Data Center (NCDC) in Asheville, North Carolina. The 195 stations encompass 388 unique sampling locations in 48 of the 50 states; no observations from Delaware or Hawaii are included in the database. Station selection criteria emphasized the quality and length of station records while seeking to provide a network with good geographic coverage. Snow depth at the 388 locations was measured once per day on ground open to the sky. The daily snow depth is the total depth of the snow on the ground at measurement time. The time period covered by the database is 1893--1992; however, not all station records encompass the complete period. While a station record ideally should contain daily data for at least the seven winter months (January through April and October through December), not all stations have complete records. Each logical record in the snow depth database contains one station`s daily data values for a period of one month, including data source, measurement, and quality flags.

Allison, L.J. [ed.] [Oak Ridge National Lab., TN (United States). Carbon Dioxide Information Analysis Center; Easterling, D.R.; Jamason, P.; Bowman, D.P.; Hughes, P.Y.; Mason, E.H. [National Oceanic and Atmospheric Administration, Asheville, NC (United States). National Climatic Data Center

1997-02-01T23:59:59.000Z

88

Constrained ceramic-filled polymer armor  

DOE Patents [OSTI]

An armor system is disclosed in which a plurality of constraint cells are mounted on a surface of a substrate, which is metal armor plate or a similar tough material, such that the cells almost completely cover the surface of the substrate. Each constraint cell has a projectile-receiving wall parallel to the substrate surface and has sides which are perpendicular to and surround the perimeter of the receiving wall. The cells are mounted such that, in one embodiment, the substrate surface serves as a sixth side or closure for each cell. Each cell has inside of it a plate, termed the front plate, which is parallel to and in contact with substantially all of the inside surface of the receiving wall. The balance of each cell is completely filled with a projectile-abrading material, which is a ceramic material in particulate form dispersed in a polymeric matrix. 5 figs.

Sandstrom, D.J.; Calkins, N.C.; Gac, F.D.

1990-11-13T23:59:59.000Z

89

Constrained ceramic-filled polymer armor  

DOE Patents [OSTI]

An armor system in which a plurality of constraint cells are mounted on a surface of a substrate, which is metal armor plate or a similar tough material, such that the cells almost completely cover the surface of the substrate. Each constraint cell has a projectile-receiving wall parallel to the substrate surface and has sides which are perpendicular to and surround the perimeter of the receiving wall. The cells are mounted such that, in one embodiment, the substrate surface serves as a sixth side or closure for each cell. Each cell has inside of it a plate, termed the front plate, which is parallel to and in contact with substantially all of the inside surface of the receiving wall. The balance of each cell is completely filled with a projectile-abrading material, which is a ceramic material in particulate form dispersed in a polymeric matrix.

Sandstrom, Donald J. (Santa Fe, NM); Calkins, Noel C. (Los Alamos, NM); Gac, Frank D. (Los Alamos, NM)

1990-01-01T23:59:59.000Z

90

Method of filling a microchannel separation column  

DOE Patents [OSTI]

A method for packing a stationary phase into a small diameter fluid passageway or flow channel. Capillary action is employed to distribute a stationary phase uniformly along both the length and diameter of the flow channel. The method disclosed here: 1) eliminates the need for high pressure pumps and fittings and the safety hazards associated therewith; 2) allows the use of readily available commercial microparticles, either coated or uncoated, as the stationary phase; 3) provides for different types of particles, different particle sizes, and different particle size distributions to be packed in sequence, or simultaneously; 4) eliminates the need for plugging the flow channel prior to adding the stationary phase to retain the packing particles; and 5) many capillaries can be filled simultaneously.

Arnold, Don W. (Livermore, CA)

2002-01-01T23:59:59.000Z

91

Aging Studies of Filled and Unfilled VCE  

SciTech Connect (OSTI)

This report presents data on the effects of temperature and gamma radiation on the chemical and structural properties of both filled and unfilled VCE material produced by the Kansas City Plant using WR-qualified processes. Thermal effects up to 300 C and gamma irradiation doses of 1 MRad and 25 MRad were investigated under atmospheric conditions. Characterization techniques used in the study comprise Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), X-ray Diffraction (XRD), Tensile Testing, Solid Phase MicroExtraction - Gas Chromatography/Mass Spectrometry (SPME-GC/MS), phenol extraction followed by HPLC, and various Nuclear Magnetic Resonance (NMR) techniques including: {sup 13}C, {sup 13}C {l_brace}{sup 1}H{r_brace} cross polarization (CP), {sup 1}H magic angle spinning (MAS), 13C{l_brace}{sup 1}H{r_brace} Wide-line-Separation (2D-WISE) and development of Center band-Only Detection of Exchange (CODEX).

Letant, S; Herberg, J; Alviso, C; Small, W; Mulcahy, H; Pearson, M; Wilson, T; Chinn, S; Maxwell, R

2009-11-10T23:59:59.000Z

92

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

e.g. co-locate with gasoline station, bus-yard, or officeintegrated into existing gasoline stations with 8 dispensersof a liquid H 2 and gasoline station layout. Figure 4-9:

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

93

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

located at an existing gasoline station. One could use othere.g. co-locate with gasoline station, bus-yard, or officeequivalent to about 6% of gasoline stations in California 4.

Lipman, T E; Weinert, Jonathan X.

2006-01-01T23:59:59.000Z

94

Mobile Alternative Fueling Station Locator  

SciTech Connect (OSTI)

The Department of Energy's Alternative Fueling Station Locator is available on-the-go via cell phones, BlackBerrys, or other personal handheld devices. The mobile locator allows users to find the five closest biodiesel, electricity, E85, hydrogen, natural gas, and propane fueling sites using Google technology.

Not Available

2009-04-01T23:59:59.000Z

95

NOAA PMEL Station Chemistry Data  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

Submicron and supermicron samples are analyzed by ion chromatography for Cl-, NO3-, SO4-2, Na+, NH4+, K+, Mg2+, and Ca+2. The analysis of MSA-, Br-, and oxalate has been added to some stations. Samples also are analyzed for total mass by gravimetric analysis at 55 +/- 5% RH.

Quinn, Patricia

96

Presented by Climate End Station  

E-Print Network [OSTI]

.S. Department of Energy Bettge_LCF Climate_SC10 CESM working groups · Application ­ Climate change, paleoclimate climate change projections for IPCC AR5 Gerald Meehl and Warren Washington, NCAR · Climate changePresented by Climate End Station Thomas Bettge National Center for Atmospheric Research James B

97

Improving Robust Rolling Stock Circulation in Rapid Transit Networks  

E-Print Network [OSTI]

Aug 31, 2011 ... Constraints (5) ensure material flow balance in each depot station for ... in the network, RENFE planners always reserve some material and, ...

2011-08-31T23:59:59.000Z

98

Hanford Meteorological Station computer codes: Volume 1, The GEN computer code  

SciTech Connect (OSTI)

The Hanford Meteorological Station, operated by Pacific Northwest Laboratory, issues general weather forecasts twice a day. The GEN computer code is used to archive the 24-hour forecasts and apply quality assurance checks to the forecast data. This code accesses an input file, which contains the date and hour of the previous forecast, and an output file, which contains 24-hour forecasts for the current month. As part of the program, a data entry form consisting of 14 fields that describe various weather conditions must be filled in. The information on the form is appended to the current 24-hour monthly forecast file, which provides an archive for the 24-hour general weather forecasts. This report consists of several volumes documenting the various computer codes used at the Hanford Meteorological Station. This volume describes the implementation and operation of the GEN computer code at the station.

Buck, J.W.; Andrews, G.L.

1987-07-01T23:59:59.000Z

99

Synthesis of Space-Filling Curves Through Measure- Preserving ...  

E-Print Network [OSTI]

... des courbes ?-denses,. Economica, Paris, 2005 (in French). ... [8] H. A. Ghali and T. A. Moselhy, Broad-band and circularly polarized space- filling-based slot ...

Administrador

2010-04-08T23:59:59.000Z

100

COMPARATIVE COSTS OF CALIFORNIA CENTRAL STATION ELECTRICITY  

E-Print Network [OSTI]

CALIFORNIA ENERGY COMMISSION COMPARATIVE COSTS OF CALIFORNIA CENTRAL STATION ELECTRICITY GENERATION .............................................................................13 Definition of Levelized Cost ........................................................................................................13 Levelized Cost Components

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

COMPARATIVE COSTS OF CALIFORNIA CENTRAL STATION ELECTRICITY  

E-Print Network [OSTI]

CALIFORNIA ENERGY COMMISSION COMPARATIVE COSTS OF CALIFORNIA CENTRAL STATION ELECTRICITY GENERATION............................................................ 3 Definition of Levelized Cost.................................................................................... 3 Levelized Cost Categories

Laughlin, Robert B.

102

7.1.1. Fernbahnhof / Rail Station  

E-Print Network [OSTI]

Fernbahnhofs 7.1.1.4.5 Kälteversorgung des Fernbahnhofs / Cooling Supply of Rail Station 7 Abwasserversorgung des Fernbahnhofs / Fresh and Used Water Supply of Rail Stations 7.1.1.4.1.1 Verfahren zur Fernbahnhofs 7.1.1.4.2 Stromversorgung des Fernbahnhofs / Power Supply of Rail Station 7

Berlin,Technische Universität

103

Transportation Science and the Dynamics of Critical Infrastructure Networks with  

E-Print Network [OSTI]

Network Satellite and Undersea Cable Networks British Electricity Grid Transportation, Communication Automobiles, Trains, and Planes, Manufacturing and logistics Workstations, Distribution Points Processing Cables Radio Links Voice, Data, Video Energy Pumping Stations, Plants Pipelines, Transmission Lines Water

Nagurney, Anna

104

Critical Infrastructure Networks and Supernetworks: New Tools for Dynamics,  

E-Print Network [OSTI]

Constellation Network Satellite and Undersea Cable Networks British Electricity Grid Transportation Automobiles, Trains, and Planes, Manufacturing and logistics Workstations, Distribution Points Processing Cables Radio Links Voice, Data, Video Energy Pumping Stations, Plants Pipelines, Transmission Lines Water

Nagurney, Anna

105

Modeling of Reoxidation Inclusion Formation During Filling of Steel Castings  

E-Print Network [OSTI]

1 Modeling of Reoxidation Inclusion Formation During Filling of Steel Castings Kent D. Carlson cycle of inclusions during the filling of steel castings. There are two ways that inclusions can the final location and characteristics of reoxidation inclusions in steel castings. Carlson, K

Beckermann, Christoph

106

Timber Mountain Precipitation Monitoring Station  

SciTech Connect (OSTI)

A precipitation monitoring station was placed on the west flank of Timber Mountain during the year 2010. It is located in an isolated highland area near the western border of the Nevada National Security Site (NNSS), south of Pahute Mesa. The cost of the equipment, permitting, and installation was provided by the Environmental Monitoring Systems Initiative (EMSI) project. Data collection, analysis, and maintenance of the station during fiscal year 2011 was funded by the U.S. Department of Energy, National Nuclear Security Administration, Nevada Site Office Environmental Restoration, Soils Activity. The station is located near the western headwaters of Forty Mile Wash on the Nevada Test and Training Range (NTTR). Overland flows from precipitation events that occur in the Timber Mountain high elevation area cross several of the contaminated Soils project CAU (Corrective Action Unit) sites located in the Forty Mile Wash watershed. Rain-on-snow events in the early winter and spring around Timber Mountain have contributed to several significant flow events in Forty Mile Wash. The data from the new precipitation gauge at Timber Mountain will provide important information for determining runoff response to precipitation events in this area of the NNSS. Timber Mountain is also a groundwater recharge area, and estimation of recharge from precipitation was important for the EMSI project in determining groundwater flowpaths and designing effective groundwater monitoring for Yucca Mountain. Recharge estimation additionally provides benefit to the Underground Test Area Sub-project analysis of groundwater flow direction and velocity from nuclear test areas on Pahute Mesa. Additionally, this site provides data that has been used during wild fire events and provided a singular monitoring location of the extreme precipitation events during December 2010 (see data section for more details). This letter report provides a summary of the site location, equipment, and data collected in fiscal year 2011.

Lyles Brad,McCurdy Greg,Chapman Jenny,Miller Julianne

2012-01-01T23:59:59.000Z

107

Hanford Meteorological Station - Hanford Site  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinanInformation Desert Southwest Region service area. TheEPSCIResearchGulf of MexicoDidYouKnowForStation

108

Pressures on Arizona Water and Energy Policy: Case Study of the Navajo Generating Station  

E-Print Network [OSTI]

largest user of energy in the state of Arizona. It is powered by a coal plant in Northern Arizona1 Pressures on Arizona Water and Energy Policy: Case Study of the Navajo Generating Station Sonya Sustainability Graduate Student Fellowship Program & The Renewable Energy Network, Renewable Energy Policy

Fay, Noah

109

Mobile Ad Hoc Networks Asis Nasipuri  

E-Print Network [OSTI]

1 Mobile Ad Hoc Networks Asis Nasipuri Department of Electrical & Computer Engineering The University of North Carolina at Charlotte Charlotte, NC 28223-0001 I. INTRODUCTION A mobile ad hoc network of base stations, make ad hoc networks radically different from other wireless LANs. Whereas communication

Nasipuri, Asis

110

Hydrogen refueling station costs in Shanghai  

E-Print Network [OSTI]

total installed capital cost (TIC) 1% Of TIC 25% Estimate ofcost estimates for six station types SMR 100 a Equipment capital

Weinert, Jonathan X.; Shaojun, Liu; Ogden, Joan M; Jianxin, Ma

2007-01-01T23:59:59.000Z

111

Kansas Nuclear Profile - Wolf Creek Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

April 2012" "Next Release Date: February 2013" "Wolf Creek Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor...

112

Washington Nuclear Profile - Columbia Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

Columbia Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration...

113

Illinois Nuclear Profile - Dresden Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

Dresden Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration...

114

Illinois Nuclear Profile - Clinton Power Station  

U.S. Energy Information Administration (EIA) Indexed Site

Clinton Power Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration date"...

115

Illinois Nuclear Profile - Byron Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

Byron Generating Station" ,"Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration date"...

116

Massachusetts Nuclear Profile - Pilgrim Nuclear Power Station  

U.S. Energy Information Administration (EIA) Indexed Site

Pilgrim Nuclear Power Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer cpacity factor (percent)","Type","Commercial operation date","License...

117

Illinois Nuclear Profile - Braidwood Generation Station  

U.S. Energy Information Administration (EIA) Indexed Site

Braidwood Generation Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

118

Hydrogen Fueling Infrastructure Research and Station Technology...  

Energy Savers [EERE]

Infrastructure Research and Station Technology Download presentation slides from the DOE Fuel Cell Technologies Office webinar "An Overview of the Hydrogen Fueling Infrastructure...

119

Hydrogen refueling station costs in Shanghai  

E-Print Network [OSTI]

Fueling stations; Cost; Shanghai; Fuel cell vehicles 1.and the delivery cost for fuel cell vehicles, however, itthus hydrogen cost therefore depend on the ?eet of fuel cell

Weinert, Jonathan X.; Shaojun, Liu; Ogden, Joan M; Jianxin, Ma

2007-01-01T23:59:59.000Z

120

Closed form solutions for symmetric water filling games  

E-Print Network [OSTI]

Closed form solutions for symmetric water filling games E. Altman INRIA Sophia Antipolis, France Email: altman@sophia.inria.fr K. Avrachenkov INRIA Sophia Antipolis, France Email: k.avrachenkov@sophia

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Boiling and condensation in a liquid-filled enclosure  

E-Print Network [OSTI]

A combined experimental and analytical investigation of boiling and condensation in a liquid-filled enclosure, with water and Freon- 113 as the working fluids, is described. The operating characteristics of a boiling system, ...

Bar-Cohen Avram

1971-01-01T23:59:59.000Z

122

Acoustical wave propagation in buried water filled pipes  

E-Print Network [OSTI]

This thesis presents a comprehensive way of dealing with the problem of acoustical wave propagation in cylindrically layered media with a specific application in water-filled underground pipes. The problem is studied in ...

Kondis, Antonios, 1980-

2005-01-01T23:59:59.000Z

123

Tank 41-H salt level fill history 1985 to 1987  

SciTech Connect (OSTI)

The fill rate of the evaporator drop waste tank (i.e., salt tank) at Savannah River Site contained in the Waste Management Technology (WMT) monthly data record is based upon a simple formula that apportioned 10 percent of the evaporator output concentrate to the salt fill volume. Periodically, the liquid level of the salt tank would be decanted below the salt level surface and a visual inspection of the salt profile would be accomplished. The salt volume of the drop tank would then be corrected, if necessary, based upon the visual elevation of the salt formation. This correction can erroneously indicate an excess amount of salt fill occurred in a short time period. This report established the correct fill history for Tank 41H.

Ross, R.H.

1996-05-16T23:59:59.000Z

124

New Mexico Surface Water Quality Bureau Federal Dredge and Fill...  

Open Energy Info (EERE)

New Mexico Surface Water Quality Bureau Federal Dredge and Fill Permits webpage Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: New Mexico Surface...

125

System and method for filling a plurality of isolated vehicle fluid circuits through a common fluid fill port  

SciTech Connect (OSTI)

A vehicle having multiple isolated fluid circuits configured to be filled through a common fill port includes a first fluid circuit disposed within the vehicle, the first fluid circuit having a first fill port, a second fluid circuit disposed within the vehicle, and a conduit defining a fluid passageway between the first fluid circuit and second fluid circuit, the conduit including a valve. The valve is configured such that the first and second fluid circuits are fluidly coupled via the passageway when the valve is open, and are fluidly isolated when the valve is closed.

Sullivan, Scott C; Fansler, Douglas

2014-10-14T23:59:59.000Z

126

An evaluation of the critical mechanical properties of filled elastomers  

E-Print Network [OSTI]

AN EVALUATION OF THE CRITICAL MECHANICAL PROPERTIES OF FILLED ELASTOMERS A Thesis By PATRICK ARTHUR GIBSON Submitted to the Graduate College of the Texas ASM University in partial fulfillment of the requirements for the degree of MASTER... possible. ABSTRACT An Evaluation of the Critical Mechanical Properties of Filled Elastomers Patrick A. Gibson, B. S. , Texas ASM University Directed by: Dr. William B. Ledbetter A test procedure is developed for the uniaxial tensile testing...

Gibson, Patrick Arthur

2012-06-07T23:59:59.000Z

127

Fluorinated diamond particles bonded in a filled fluorocarbon resin matrix  

DOE Patents [OSTI]

A method of producing fluorinated diamond particles bonded in a filled fluorocarbon resin matrix. Simple hot pressing techniques permit the formation of such matrices from which diamond impregnated grinding tools and other articles of manufacture can be produced. Teflon fluorocarbon resins filled with Al/sub 2/O/sub 3/ yield grinding tools with substantially improved work-to-wear ratios over grinding wheels known in the art.

Taylor, G.W.; Roybal, H.E.

1983-11-14T23:59:59.000Z

128

Fluorinated diamond particles bonded in a filled fluorocarbon resin matrix  

DOE Patents [OSTI]

A method of producing fluorinated diamond particles bonded in a filled fluorocarbon resin matrix. Simple hot pressing techniques permit the formation of such matrices from which diamond impregnated grinding tools and other articles of manufacture can be produced. Teflon fluorocarbon resins filled with Al.sub.2 O.sub.3 yield grinding tools with substantially improved work-to-wear ratios over grinding wheels known in the art.

Taylor, Gene W. (Los Alamos, NM); Roybal, Herman E. (Santa Fe, NM)

1985-01-01T23:59:59.000Z

129

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

4-12: Hydrogen Cost Comparison for Electrolysis Station WithAnalysis: Electrolysis, 30 kg/day, grid Hydrogen Cost ($/kg)the hydrogen costs from the HSCM for electrolysis stations

Lipman, T E; Weinert, Jonathan X.

2006-01-01T23:59:59.000Z

130

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

4: Energy Station Grid electricity Cogen Heat Exhaust (CO2)Recycled Reformate Grid electricity Cogen Heat Electricity

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

131

E-Print Network 3.0 - analyze cellular localization Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Energy-Efficient Operation of Cellular Network Infrastructure Summary: at which base station operation decisions should be made? At what locality level of the cellular...

132

(Hydrogen) Service Stations 101 Steven M. Schlasner  

E-Print Network [OSTI]

(Hydrogen) Service Stations 101 Steven M. Schlasner September 22, 2004 #12;2 DISCLAIMER Opinions · Comparison of Conventional with Hydrogen Fueling Stations · Hydrogen Fueling Life Cycle · Practical Design,000 retail outlets (350 company-owned) in 44 states · Brands: Conoco, Phillips 66, 76 · 32,800 miles pipeline

133

High speed imager test station  

DOE Patents [OSTI]

A test station enables the performance of a solid state imager (herein called a focal plane array or FPA) to be determined at high image frame rates. A programmable waveform generator is adapted to generate clock pulses at determinable rates for clock light-induced charges from a FPA. The FPA is mounted on an imager header board for placing the imager in operable proximity to level shifters for receiving the clock pulses and outputting pulses effective to clock charge from the pixels forming the FPA. Each of the clock level shifters is driven by leading and trailing edge portions of the clock pulses to reduce power dissipation in the FPA. Analog circuits receive output charge pulses clocked from the FPA pixels. The analog circuits condition the charge pulses to cancel noise in the pulses and to determine and hold a peak value of the charge for digitizing. A high speed digitizer receives the peak signal value and outputs a digital representation of each one of the charge pulses. A video system then displays an image associated with the digital representation of the output charge pulses clocked from the FPA. In one embodiment, the FPA image is formatted to a standard video format for display on conventional video equipment. 12 figs.

Yates, G.J.; Albright, K.L.; Turko, B.T.

1995-11-14T23:59:59.000Z

134

A Distributed Protocol for the Bounded-Hops Converge-cast in Ad-Hoc Networks0  

E-Print Network [OSTI]

A Distributed Protocol for the Bounded-Hops Converge-cast in Ad-Hoc Networks0 Andrea E. F. Clementi (centralized) heuristics. 1 Introduction An ad-hoc (wireless) network consists of a set of radio stations connected by wireless links. In an ad hoc network, a transmission range is assigned to every station

Rossi, Gianluca

135

Lattice thermal conductivity of filled skutterudites: An anharmonicity perspective  

SciTech Connect (OSTI)

We report a phenomenological model to calculate the high-temperature lattice thermal conductivity of filled skutterudite antimonides. The model needs no phonon resonant scattering terms. Instead, we assume that umklapp processes dominate the high-temperature phonon scattering. In order to represent the anharmonicity introduced by the filling atom, we introduce a Gaussian term into the relaxation time of the umklapp process. The developed model agrees remarkably well with the experimental results of RE{sub f}Co{sub 4}Sb{sub 12} and RE{sub f}Fe{sub 4}Sb{sub 12} (RE?=?Yb, Ba, and Ca) alloys. To further test the validity of our model, we calculate the lattice thermal conductivity of nanostructured or multi-filled skutterudites. The calculation results are also in good agreement with experiment, increasing our confidence in the developed anharmonicity model.

Geng, Huiyuan, E-mail: genghuiyuan@hit.edu.cn; Meng, Xianfu; Zhang, Hao; Zhang, Jian [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China)

2014-10-28T23:59:59.000Z

136

23rd steam-station cost survey  

SciTech Connect (OSTI)

The results of the 23rd Steam Station Cost Survey covering the year 1982 are summarized. The major categories of the survey are as follows: general data; output data, 1982; fuel consumption, 1982; operation 1982 (mills/net kWh); investment ($/net kWh); energy cost, 1982 (mills/net kWh); and station performance, 1982. Thirty-one fossil-fuel steam plants and four nuclear stations were included in the survey. Fuel and operating cost increases are felt to be responsible for the moderate rise in total busbar-enery costs. 11 figures, 1 table.

Friedlander, G.D.; Going, M.C.

1983-11-01T23:59:59.000Z

137

University Climatological Station Compiled by Erwin Wodarczak (1998)  

E-Print Network [OSTI]

University Climatological Station Committee fonds Compiled by Erwin Wodarczak (1998) #12;Fonds Description University Climatological Station Committee fonds. ­ 1961-1974. 3 cm of textual records. Administrative History In 1954 a President's Climatological Station Committee was established

Handy, Todd C.

138

A Near-Term Economic Analysis of Hydrogen Fueling Stations  

E-Print Network [OSTI]

0.07/kWh has on hydrogen cost for electrolysis type station.3-12: Hydrogen Cost Comparison for Electrolysis Station,3-12: Hydrogen Cost Comparison for Electrolysis Station, NAS

Weinert, Jonathan X.

2005-01-01T23:59:59.000Z

139

A Near-term Economic Analysis of Hydrogen Fueling Stations  

E-Print Network [OSTI]

0.07/kWh has on hydrogen cost for electrolysis type station.3-12: Hydrogen Cost Comparison for Electrolysis Station,3-12: Hydrogen Cost Comparison for Electrolysis Station, NAS

Weinert, Jonathan X.

2005-01-01T23:59:59.000Z

140

Exhaustive search system and method using space-filling curves  

DOE Patents [OSTI]

A search system and method for one agent or for multiple agents using a space-filling curve provides a way to control one or more agents to cover an area of any space of any dimensionality using an exhaustive search pattern. An example of the space-filling curve is a Hilbert curve. The search area can be a physical geography, a cyberspace search area, or an area searchable by computing resources. The search agent can be one or more physical agents, such as a robot, and can be software agents for searching cyberspace.

Spires, Shannon V.

2003-10-21T23:59:59.000Z

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Bose-Hubbard phase diagram with arbitrary integer filling  

SciTech Connect (OSTI)

We study the transition from a Mott insulator to a superfluid in both the two- and the three-dimensional Bose-Hubbard model at zero temperature, employing the method of the effective potential. Converting Kato's perturbation series into an algorithm capable of reaching high orders, we obtain accurate critical parameters for any integer filling factor. Our technique allows us to monitor both the approach to the mean-field limit by considering spatial dimensionalities d>3 and to the quantum rotor limit of high filling, which refers to an array of Josephson junctions.

Teichmann, Niklas; Hinrichs, Dennis; Holthaus, Martin; Eckardt, Andre [Institut fuer Physik, Carl von Ossietzky Universitaet, D-26111 Oldenburg (Germany); Institut de Ciencies Fotoniques (ICFO), E-08860 Castelldefels, Barcelona (Spain)

2009-03-01T23:59:59.000Z

142

Plasma-filled diode based on the coaxial gun  

SciTech Connect (OSTI)

The paper presents the results of studies of a coaxial gun for a plasma-filled electron diode. Effects of the discharge channel diameter and gun current on characteristics of the plasma and pulse generated in the diode were investigated. The electron beam with maximum energy of {>=}1 MeV at the current of Almost-Equal-To 100 kA was obtained in the experiments with a plasma-filled diode. The energy of Almost-Equal-To 5 kJ with the peak power of {>=}100 GW dissipated in the diode.

Zherlitsyn, A. A.; Kovalchuk, B. M.; Pedin, N. N. [Institute of High Current Electronics, 2/3 Academichesky Avenue, 634055 Tomsk (Russian Federation)

2012-10-15T23:59:59.000Z

143

Hydrogen Fueling Station in Honolulu, Hawaii Feasibility Analysis...  

Broader source: Energy.gov (indexed) [DOE]

Station in Honolulu, Hawaii Feasibility Analysis Hydrogen Fueling Station in Honolulu, Hawaii Feasibility Analysis This feasibility report assesses the technical and economic...

144

EECBG Success Story: Police Station Triples Solar Power - and...  

Broader source: Energy.gov (indexed) [DOE]

Police Station Triples Solar Power - and Savings EECBG Success Story: Police Station Triples Solar Power - and Savings July 19, 2010 - 11:00am Addthis North Community Police...

145

Alternative Fueling Station Locator App Provides Info at Your...  

Broader source: Energy.gov (indexed) [DOE]

Fueling Station Locator website. It provides information on more than 15,000 public and private alternative fueling stations throughout the United States. The app lists where...

146

Pdc - The Worldwide Leader in Hydrogen Refueling Station Compression...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Pdc - The Worldwide Leader in Hydrogen Refueling Station Compression Pdc - The Worldwide Leader in Hydrogen Refueling Station Compression This presentation by Matther Weaver of Pdc...

147

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network [OSTI]

stations and vendors (e.g. Air Products and Chemicals, Inc,including Chevron and Air Products and Chemicals, Inc. , asDiesel a. Verified with Air Products representative, Feb

Weinert, Jonathan X.; Shaojun, Liu; Ogden, J; Jianxin, Ma

2006-01-01T23:59:59.000Z

148

IntegratedScienceWorkingforYou Research Station  

E-Print Network [OSTI]

. . . . . . . . . . . . . . . . . . .5 Colorado's forest resources, 2002-2006 . . . . . . . . .6 Post Mountain Research Station Federal Recycling Program Printed on Recycled Paper The Rocky Mountain Research organi- zation--the most extensive natural resources research organization in the world. We maintain 14

149

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network [OSTI]

and the delivery cost for fuel cell vehicles, however, itfueling stations, cost, Shanghai, fuel cell vehicles 1.0hydrogen cost therefore depend on the fleet of fuel cell

Weinert, Jonathan X.; Shaojun, Liu; Ogden, J; Jianxin, Ma

2006-01-01T23:59:59.000Z

150

The College Station Residential Energy Compliance Code  

E-Print Network [OSTI]

The City of College Station, Texas adopted a new residential Energy Compliance Code in January, 1988. The code, which strengthens compliance requirements in several areas, has received broadly based support and acceptance from all major constituent...

Claridge, D. E.; Schrock, D.

1988-01-01T23:59:59.000Z

151

Field Station Contributors, 2010 Acton, Gary  

E-Print Network [OSTI]

Field Station Contributors, 2010 Acton, Gary Allen, Deborah and Harry Ardell, Robert and Lee Baker Mead, Judson and Jane Mead, Thomas and Lenore Merritt, Andrew and Eleanor Morganwalp, David and Jill

Polly, David

152

Hydrogen Refueling Station Costs in Shanghai  

E-Print Network [OSTI]

Well-to-wheels analysis of hydrogen based fuel-cell vehicleJP, et al. Distributed Hydrogen Fueling Systems Analysis,”Year 2006 UCD—ITS—RR—06—04 Hydrogen Refueling Station Costs

Weinert, Jonathan X.; Shaojun, Liu; Ogden, Joan M; Jianxin, Ma

2006-01-01T23:59:59.000Z

153

Hydrogen Fueling Infrastructure Research and Station Technology  

Broader source: Energy.gov [DOE]

Presentation slides from the DOE Fuel Cell Technologies Office webinar "An Overview of the Hydrogen Fueling Infrastructure Research and Station Technology (H2FIRST) Project" held on November 18, 2014.

154

Network Management Network Management  

E-Print Network [OSTI]

that pertain to the operation, administration, maintenance, and provisioning of networked systems · Operation deals with keeping the network up (and the service provided by the network) · Administration involvesNetwork Management Pag. 1 Network Management Andrea Bianco Telecommunication Network Group Network

155

Repowering of the Midland Nuclear Station  

E-Print Network [OSTI]

REPOWERING OF THE MIDLAND NUCLEAR STATION C.E. Gatlin Jr. Gerald C. Velleroer Janes A. Mooney Manager of Projects Fluor Daniel, IrK::. Vice President Fluor Daniel, IrK::. Vice President Midlarrl eogneneration Venture Chicago, Illinois... Chicago, Illinois Midland, Michigan The conversion of the Midland Nuclear Station to a combined cycle power facility is the first of its kind. The eXisting nuclear steam turbine, combined with new, natural-gas-fired gas turbines, will create...

Gatlin, C. E. Jr.; Vellender, G. C.; Mooney, J. A.

156

Emerging Trends in Failures Involving EPS-Block Geofoam Fills  

E-Print Network [OSTI]

Emerging Trends in Failures Involving EPS-Block Geofoam Fills John S. Horvath, Ph.D., P.E., M.ASCE1 Abstract: Expanded polystyrene EPS is a closed-cell polymeric "plastic" foam that, in its generic block is due to the fact that block-molded EPS is unique among geofoam products for the large and diverse

Horvath, John S.

157

Physics Pathway: A Digital Library Filled with Synthetic Interviews*  

E-Print Network [OSTI]

Physics Pathway: A Digital Library Filled with Synthetic Interviews* Michael G. Christel-412-268-7796 sms@cs.cmu.edu Dean Zollman Department of Physics Kansas State University Manhattan, KS 66506 1-785-532-1619 dzollman@phys.ksu.edu ABSTRACT Physics Pathway is a digital library available through an Adobe Flash portal

Christel, Mike

158

ORIGINAL PAPER BambooFiber Filled High Density Polyethylene Composites  

E-Print Network [OSTI]

ORIGINAL PAPER Bamboo­Fiber Filled High Density Polyethylene Composites: Effect of Coupling Springer Science+Business Media, LLC 2008 Abstract High density polyethylene (HDPE)/bamboo composites in the future study. Keywords Bamboo Á High density polyethylene Á Coupling treatment Á Nanoclay Introduction

159

Analysis of tubes filled with charged electron gas  

E-Print Network [OSTI]

We show that tubes filled with electron gas, as presented by A.Bolonkin, are not possible with current materials. First, the pressure of the charges on the outer surface cancel almost all of the electrostatic pressure of the inner electrons. Second, due to the mutually repulsion most of the electrons are in the outmost shell of the tube and not individually free.

Stefan Karrmann

2011-02-24T23:59:59.000Z

160

Engineering study of tank fill options for landfill closure  

SciTech Connect (OSTI)

To prepare single-shell tanks for closure, it will be necessary to piece some type of load- bearing fill material inside the tanks to support the domes. Provision of internal support permits the simplifying assumption that the combined weight of the dome, the existing operational soil cover, and the surface barrier will eventually transfer to and be carried by the fill. This engineering study provides descriptions and evaluations of four alternative concepts for fitting and stabilizing nominally empty SSTs with fill materials. For this study it is assumed that 99 percent (or more) of tank wastes will be retrieved before closure is undertaken. The alternatives are: Gravel: tanks would be fitted with crushed aggregate using a rotating stinger apparatus installed in the central riser; Grout: tanks would be fitted with a pumpable, ex-situ mixed grout formulation; Hybrid: tanks would be fitted first with coarse aggregate, then with grout, producing a pre-placed aggregate concrete material; or Concrete: tank. would be filled with a highly-flowable, ex-situ mixed concrete formulation.

Skelly, W.A.

1996-09-27T23:59:59.000Z

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Method and apparatus for filling thermal insulating systems  

DOE Patents [OSTI]

A method for filling insulated glazing units is disclosed. The method utilizes a vacuum chamber in which the insulated glazing units are placed. The insulated glazing units and vacuum chamber are evacuated simultaneously. The units are then refilled with a low conductance gas such as Krypton while the chamber is simultaneously refilled with air. 3 figs.

Arasteh, D.K.

1992-01-14T23:59:59.000Z

162

arctic research station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

The Rocky Mountain Research Sta- tion is one of five 19 Z .Atmospheric Research 51 1999 4575 Cloud resolving simulations of Arctic stratus Geosciences Websites Summary: Z...

163

albright generating station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Statement for License Renewal of Nuclear Plants (GEIS), NUREG-1437 (NRC, 1996), (NRC, 1999); (2) the Environmental Report submitted by DEK; (3) consultation with Federal, State,...

164

animal testing station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

J. HANLON Department of Biology, Washington and Lee University (Received online 27 October 2004; MS. number: A9684) Most studies of animal behaviour are based on direct Marsh,...

165

agricultural experiment station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

12;Agriculture performance standards & County Land and Water Resource Management Plan Balser, Teri C. 455 Agricultural Outlook ORGANISATION FOR ECONOMIC Environmental...

166

agricultural experiment stations: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

12;Agriculture performance standards & County Land and Water Resource Management Plan Balser, Teri C. 455 Agricultural Outlook ORGANISATION FOR ECONOMIC Environmental...

167

antarctic research station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Canada, following appIes (Matus domestica Barkh.) and grapes (Vizisspp.). In 1988 Biggs, Alan R. 18 ANNUAL REVIEW 2011 Antarctic Research Centre Environmental Sciences and...

168

antarctic receiving station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and Antarctic) have been considered as bellwethers in the detection of global climate change. According to IPCC (2001), Climate change in polar regions is expected to be among...

169

automatic weather stations: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

analysis to assist agencies participating in the Texas LoanSTAR Monitoring and Analysis Program. A review of the sensors and procedures... Crowley, G. D.; Haberl, J. S....

170

automatic weather station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

analysis to assist agencies participating in the Texas LoanSTAR Monitoring and Analysis Program. A review of the sensors and procedures... Crowley, G. D.; Haberl, J. S....

171

atomic power station-2: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

power of 42 VK with a big change (9.6 Feenstra, Randall 7 Power laws and fractal behavior in nuclear stability, atomic weights and molecular weights Physics Websites...

172

aerosol sampling stations: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in two modes: (1) a continuous mass spectrum mode without size information; and (2) a size distribution measurement mode for selected mz settings of the quadrupole. Single...

173

MHK Technologies/Vert Network Power Station | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpIncMAKGalway Bay IEOWC <SurgeWECSailsOWC.pngflow Turbine

174

agr power stations: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Millport 12;What is Millport? Marine biology teaching in the local marine environment, biological communities and policy context Particular interests in fisheries...

175

atomic power station: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Millport 12;What is Millport? Marine biology teaching in the local marine environment, biological communities and policy context Particular interests in fisheries...

176

atomic power stations: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Millport 12;What is Millport? Marine biology teaching in the local marine environment, biological communities and policy context Particular interests in fisheries...

177

Throughput Analysis of Wireless Ad-Hoc Cognitive Radio Networks  

E-Print Network [OSTI]

is independent of the primary frequency bandwidths and usage statistics; otherwise, they follow water-filling-like strategies. Next, we study the asymptotic performance of two multi-hop overlaid ad-hoc networks that utilize the same temporal, spectral...

Banaei, Armin

2014-04-25T23:59:59.000Z

178

Monitoring and optimization of energy consumption of base transceiver stations  

E-Print Network [OSTI]

The growth and development of the mobile phone network has led to an increased demand for energy by the telecommunications sector, with a noticeable impact on the environment. Monitoring of energy consumption is a great tool for understanding how to better manage this consumption and find the best strategy to adopt in order to maximize reduction of unnecessary usage of electricity. This paper reports on a monitoring campaign performed on six Base Transceiver Stations (BSs) located central Italy, with different technology, typology and technical characteristics. The study focuses on monitoring energy consumption and environmental parameters (temperature, noise, and global radiation), linking energy consumption with the load of telephone traffic and with the air conditioning functions used to cool the transmission equipment. Moreover, using experimental data collected, it is shown, with a Monte Carlo simulation based on power saving features, how the BS monitored could save energy.

Spagnuolo, Antonio; Vetromile, Carmela; Formosi, Roberto; Lubritto, Carmine

2015-01-01T23:59:59.000Z

179

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

vs. delivered hydrogen, compressor type, storage pressure).pump High-pressure hydrogen compressor Compressed hydrogenpipeline High-pressure hydrogen compressor Pipeline Station:

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

180

Call for Papers ACM/Springer Mobile Networks & Applications (MONET)  

E-Print Network [OSTI]

. Therefore, the design of energy efficiency network architecture & protocols is the key problem for green it is important to further explore the energy efficiency multi-base-station management in green mobile networks in Green Mobile Networks http://www.springer.com/engineering/signals/journal/**** Overview Global warming

Chen, Min

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Hydrogen Fueling - Coming Soon to a Station Near You (Brochure)  

SciTech Connect (OSTI)

Fact sheet providing information useful to local permitting officials facing hydrogen fueling station proposals.

Not Available

2009-04-01T23:59:59.000Z

182

Station Processing for a Low Frequency Array in WA  

E-Print Network [OSTI]

for the remote station, minus 2 kW for cooling (considered "infrastructure"). #12;Station Processing Requirements stations (regardless of role as remote or core) (yes; remote stations can be "less" not "different") 2 (yes: 2-3 for core, 1 for remote) 6. Cost: TBD. (Prorated cost of ~US$500 per dual-pol element

Ellingson, Steven W.

183

The LOFAR Super Station concept : an input for discussion  

E-Print Network [OSTI]

throughout Europe : several stations in Germany1 , UK2 , soon a French LOFAR station in Nançay3 , and further contacts in several other countries4 FLOW context · Official decision for funding the French station taken MHz) o Incoherent addition of the same stations to synthesize a broad instantaneous beam (maximum

Demoulin, Pascal

184

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

station. H2Gen’s estimates for capital costs are also lowerestimates and show high variability (26%-117% of capital costs).capital costs of about $250,000. Existing hydrogen station cost analyses tend to under-estimate

Weinert, Jonathan X.; Lipman, Timothy

2006-01-01T23:59:59.000Z

185

Powder segregation during the filling of a simple die  

E-Print Network [OSTI]

. During vibratory die f il ling, f iltration of f ines through the moving powder mass is still a major cause of segregation. The vibration tends to flatten out the inner mound of fines, thereby decreasing radial segregation and increasing vertical... SEGREGATION DURING DIE FILLING 23 l. Introduction 23 2. Experimental 2. 1. Materials 2. 2. Equipment and Procedure 23 23 24 3. Results 4. Discussion 5. Conclusions 24 24 31 III. SOME EFFECTS OF VIBRATION UPON POWDER SEGREGATION DURING DIE...

Lawrence, Larry Raymond

1968-01-01T23:59:59.000Z

186

Hydrogen fueling station development and demonstration  

SciTech Connect (OSTI)

This is the final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). This project sought to develop and demonstrate a hydrogen fueling station for vehicles. Such stations are an essential infrastructural element in the practical application of hydrogen as vehicle fuel, and a number of issues such as safety, efficiency, design, and operating procedures can only be accurately addressed by a practical demonstration. Regardless of whether the vehicle is powered by an internal combustion engine or fuel cell, or whether the vehicle has a liquid or gaseous fuel tank, the fueling station is a critical technology that is the link between the local storage facility and the vehicle.

Edeskuty, F.J.; Daney, D.; Daugherty, M.; Hill, D.; Prenger, F.C.

1996-09-01T23:59:59.000Z

187

Economic Analysis of Hydrogen Energy Station Concepts: Are "H 2E-Stations" a Key Link to a Hydrogen Fuel Cell Vehicle Infrastructure?  

E-Print Network [OSTI]

in the analysis of hydrogen energy stations, additionalattractiveness of the hydrogen energy station scheme in bothECONOMIC ANALYSIS OF HYDROGEN ENERGY STATION CONCEPTS: ARE '

Lipman, Timothy E.; Edwards, Jennifer L.; Kammen, Daniel M.

2002-01-01T23:59:59.000Z

188

Pump station for radioactive waste water  

DOE Patents [OSTI]

A pump station for transferring radioactive particle containing waste water, includes: (a.) an enclosed sump having a vertically elongated right frusto conical wall surface and a bottom surface and (b.) a submersible volute centrifugal pump having a horizontally rotating impeller and a volute exterior surface. The sump interior surface, the bottom surface and the volute exterior surface are made of stainless steel having a 30 Ra or finer surface finish. A 15 Ra finish has been found to be most cost effective. The pump station is used for transferring waste water, without accumulation of radioactive fines.

Whitton, John P.; Klos, Dean M.; Carrara, Danny T.; Minno, John J.

2003-11-18T23:59:59.000Z

189

Optimization for Design and Operation of Natural Gas Transmission Networks  

E-Print Network [OSTI]

and compressor stations. On an existing network, the model also optimizes the total flow through pipelines that satisfy demand to determine the best purchase amount of gas. A mixed integer nonlinear programming model for steady-state natural gas transmission...

Dilaveroglu, Sebnem 1986-

2012-08-22T23:59:59.000Z

190

Uniform Leader Election Protocols for Radio Networks Koji Nakano  

E-Print Network [OSTI]

Uniform Leader Election Protocols for Radio Networks #3; Koji Nakano School of Information Science be distinguished by serial or manufacturing number. The leader election problem asks to designate one of the station as leader. A leader election protocol is said to be uniform if in each time slot every station

Nakano, Koji

191

City of College Station's Thermographic Mobile Scan  

E-Print Network [OSTI]

During the first quarter of 1986, the City of College Station conducted a thermographic mobile scan of the entire city. A thermographic mobile scan is a process by which heat loss/heat gain data is accumulated by a vehicle traveling the city...

Shear, C. K.

1986-01-01T23:59:59.000Z

192

On-Site Hydrogen Generation & Refueling Station  

E-Print Network [OSTI]

of FC vehicles under real-world conditions Cost analysis vs. target of $3/gge in 2008 On-site Auto Reforming based refueling station DOE Objectives Public education on hydrogen and fuel cells Evaluation cell & HCNG busses in commercial operation ­ Refueling fuel cell & HCNG street sweepers and cars

193

TARGET STATION INFRASTRUCTURE THE CNGS EXPERIENCE  

E-Print Network [OSTI]

of Aluminum Water cooled Current: 150kA (horn) ­ 180 kA (reflector) Pulse duration 7ms #12;Key elements Remote handling Remote station for radiation survey in the target chamber #12;CNGS Target Area I per cooling circuit 2007 run radiation effects on ventilation system electronics broken flexible stripline

McDonald, Kirk

194

HATCH PROJECT PROPOSAL OKLAHOMA AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

or Revised Project Procedures for initiating a new project or for revising an existing project entail: 1. Abstracting the essential features of the objective and procedures sections from the project outline for CRISHATCH PROJECT PROPOSAL OKLAHOMA AGRICULTURAL EXPERIMENT STATION USDA PROJECT OUTLINE DEVELOPMENT

Ghajar, Afshin J.

195

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION IN COOPERATION WITH THE MICHIGAN POTATO of Crop and Soil Sciences Michigan State University East Lansing, MI 48824 Cooperators: R.W. Chase, Ray INDUSTRY COMMISSION 2004 Michigan Potato Research Report Volume 36 Left to Right: Ben Kudwa, MPIC; Caryn

Douches, David S.

196

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION IN COOPERATION WITH THE MICHIGAN POTATO INDUSTRY COMMISSION MICHIGAN POTATO RESEARCH REPORT 2003 Volume 35 Click Here to Open the 2003 Potato, S. Cooper, L. Frank, J. Driscoll, and E. Estelle Department of Crop and Soil Sciences Michigan State

Douches, David S.

197

Michigan State University Agricultural Experiment Station  

E-Print Network [OSTI]

Michigan State University Agricultural Experiment Station In Cooperation with the Michigan Potato Department of Crop and Soil Sciences Michigan State University East Lansing, MI 48824 Cooperators: R.W. Chase At Michigan State University we are breeding potatoes for the chip-processing and tablestock markets

Douches, David S.

198

Michigan State University Agricultural Experiment Station  

E-Print Network [OSTI]

Michigan State University Agricultural Experiment Station In Cooperation with the Michigan Potato. Hammerschmidt and W. Kirk Departments of Crop and Soil Sciences and Plant Pathology Michigan State University potato selections from the Michigan State University and other potato breeding programs at the Montcalm

Douches, David S.

199

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION IN COOPERATION WITH THE MICHIGAN POTATO and W. Kirk Departments of Crop and Soil Sciences and Plant Pathology Michigan State University East selections from the Michigan State University and other potato breeding programs at the Montcalm Research

Douches, David S.

200

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION  

E-Print Network [OSTI]

MICHIGAN STATE UNIVERSITY AGRICULTURAL EXPERIMENT STATION IN COOPERATION WITH THE MICHIGAN POTATO Sciences and Plant Pathology Michigan State University East Lansing, MI 48824 INTRODUCTION Each year we conduct a series of variety trials to assess advanced potato selections from the Michigan State University

Douches, David S.

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Recent developments in HVDC convertor station design  

SciTech Connect (OSTI)

New requirements on HVDC convertor station performance have emerged during the past few years. The paper presents some of these requirements and shows how they have been met through equipment and system development. This development will result in a new generation of HVDC transmissions with still better performance than for the projects presently in operation.

Carlsson, L.

1984-08-01T23:59:59.000Z

202

CASE CRITICAL The Navajo Generating Station  

E-Print Network [OSTI]

Republic The Navajo Generating Station, the largest coal-fired power plant in the West, provides electrical discussions focusing on the environmental, social, and economic implications of high-stakes threats power to customers in three states and for the Central Arizona Project to pump Colorado River water

Hall, Sharon J.

203

Green is Our Favorite Color: Students Fill in the Lines with...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Green is Our Favorite Color: Students Fill in the Lines with Energy-themed Coloring Book Green is Our Favorite Color: Students Fill in the Lines with Energy-themed Coloring Book...

204

Proactive Design of n-Type (In, Ce) Filled Skutterudites Enabling...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Design of n-Type (In, Ce) Filled Skutterudites Enabling High-Temperature Waste Heat Recovery Proactive Design of n-Type (In, Ce) Filled Skutterudites Enabling High-Temperature...

205

Slip Effects in Capillary and Parallel Disk Torsional Flows of Highly Filled Suspensions  

E-Print Network [OSTI]

filled suspensions in corotat- ing twin screw extruders.23'24 MATERIALS The matrix used in this study

206

Potential Release Site Sediment Concentrations Correlated to Storm Water Station Runoff through GIS Modeling  

SciTech Connect (OSTI)

This research examined the relationship between sediment sample data taken at Potential Release Sites (PRSs) and storm water samples taken at selected sites in and around Los Alamos National Laboratory (LANL). The PRSs had been evaluated for erosion potential and a matrix scoring system implemented. It was assumed that there would be a stronger relationship between the high erosion PRSs and the storm water samples. To establish the relationship, the research was broken into two areas. The first area was raster-based modeling, and the second area was data analysis utilizing the raster based modeling results and the sediment and storm water sample results. Two geodatabases were created utilizing raster modeling functions and the Arc Hydro program. The geodatabase created using only Arc Hydro functions contains very fine catchment drainage areas in association with the geometric network and can be used for future contaminant tracking. The second geodatabase contains sub-watersheds for all storm water stations used in the study along with a geometric network. The second area of the study focused on data analysis. The analytical sediment data table was joined to the PRSs spatial data in ArcMap. All PRSs and PRSs with high erosion potential were joined separately to create two datasets for each of 14 analytes. Only the PRSs above the background value were retained. The storm water station spatial data were joined to the table of analyte values that were either greater than the National Pollutant Discharge Elimination System (NPDES) Multi-Sector General Permit (MSGP) benchmark value, or the Department of Energy (DOE) Drinking Water Defined Contribution Guideline (DWDCG). Only the storm water stations were retained that had sample values greater than the NPDES MSGP benchmark value or the DOE DWDCG. Separate maps were created for each analyte showing the sub-watersheds, the PRSs over background, and the storm water stations greater than the NPDES MSGP benchmark value or the DOE DWDCG. Tables were then created for each analyte that listed the PRSs average value by storm water station allowing a tabular view of the mapped data. The final table that was created listed the number of high erosion PRSs and regular PRSs over background values that were contained in each watershed. An overall relationship between the high erosion PRSs or the regular PRSs and the storm water stations was not identified through the methods used in this research. However, the Arc Hydro data models created for this analysis were used to track possible sources of contamination found through sampling at the storm water gaging stations. This geometric network tracing was used to identify possible relationships between the storm water stations and the PRSs. The methods outlined for the geometric network tracing could be used to find other relationships between the sites. A cursory statistical analysis was performed which could be expanded and applied to the data sets generated during this research to establish a broader relationship between the PRSs and storm water stations.

C.T. McLean

2005-06-01T23:59:59.000Z

207

Acoustic imaging in a water filled metallic pipe  

SciTech Connect (OSTI)

A method is described for the imaging of the interior of a water filled metallic pipe using acoustical techniques. The apparatus consists of an array of 20 acoustic transducers mounted circumferentially around the pipe. Each transducer is pulsed in sequence, and the echos resulting from bubbles in the interior are digitized and processed by a computer to generate an image. The electronic control and digitizing system and the software processing of the echo signals are described. The performance of the apparatus is illustrated by the imaging of simulated bubbles consisting of thin walled glass spheres suspended in the pipe.

Kolbe, W.F.; Turko, B.T.; Leskovar, B.

1984-04-01T23:59:59.000Z

208

OPTIMIZATION STUDY FOR FILL STEM MANUFACTURINGAND PINCH WELD PROCESSING  

SciTech Connect (OSTI)

A statistically designed experiment was conducted as part of a six sigma project for Fill Stem Manufacturing and Pinch Weld Processing. This multi-year/multi-site project has successfully completed a screening study and used those results as inputs to this optimization study. Eleven welds were made using fairly tight current and cycle range. The welds demonstrate increased burst strength, longer closure length, more net displacement, and improved bond rating with increased current. However, excessive melting remains a concern from a processing viewpoint and may cause adverse metallurgical interactions. Therefore, the highest current levels specified cannot be utilized. A Validation Study is proposed for the Defense Programs Inert Facility.

Korinko, P; Karl Arnold, K

2006-09-06T23:59:59.000Z

209

Theory of Sound Propagation in Superfluid Solutions Filled Porous Media  

E-Print Network [OSTI]

A theory of the propagation of acoustic waves in a porous medium filled with superfluid solution is developed. The elastic coefficients in the system of equations are expressed in terms of physically measurable quantities. The equations obtained describe all volume modes that can propagate in a porous medium saturated with superfluid solution. Finally, derived equations are applied to the most important particular case when the normal fluid component is locked inside a highly porous media (aerogel) by viscous forces and the velocities of two longitudinal sound modes are calculated.

Sh. E. Kekutia; N. D. Chkhaidze

2005-02-10T23:59:59.000Z

210

Filling the Strategic Petroleum Reserve | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power SystemsResourcesFLASH2011-11-OPAMFY 2007 Total System12FederalReportsEnergyFieldFilling

211

An Assessment of the Near-Term Costs of Hydrogen Refueling Stations and Station Components  

E-Print Network [OSTI]

Installed Capital Figure 4-21: Cost Estimates for 1,000 kg/station. H2Gen’s estimates for capital costs are also lowerestimates and show high variability (26%-117% of capital costs).

Lipman, T E; Weinert, Jonathan X.

2006-01-01T23:59:59.000Z

212

IMPROVE XRF Analysis TI 301A: LN2 Fill/Calibration  

E-Print Network [OSTI]

IMPROVE XRF Analysis TI 301A: LN2 Fill/Calibration Page 1 of 5 TI 301A: LN2 Fills and Detector ................................................................................ 4 #12;IMPROVE XRF Analysis TI 301A: LN2 Fill/Calibration Page 2 of 5 that has been fully trained in the safety hazards of working with liquid nitrogen. #12;IMPROVE XRF

Fischer, Emily V.

213

Hierarchy of fillings for FQHE in monolayer and in bilayer graphene: Explanation of $\  

E-Print Network [OSTI]

The commensurability condition is applied to determine the hierarchy of fractional fillings of Landau levels in monolayer and bilayer graphene. The filling rates for FQHE in graphene are found and illustrated in the first three Landau levels. The good agreement with the experimental data is achieved. The presence of even denominator filling fractions in the hierarchy for FQHE in bilayer graphene is explained.

Jacak, Janusz

2015-01-01T23:59:59.000Z

214

Indexing Moving Objects by Space Filling Curves in the Dual Space  

E-Print Network [OSTI]

The Bdual ­ tree: Indexing Moving Objects by Space Filling Curves in the Dual Space By Man Lung Yiu Objects by Space Filling Curves in the Dual Space Introduction Related work Problem definition: Indexing Moving Objects by Space Filling Curves in the Dual Space Introduction Related work Problem

Kaiserslautern, Universität

215

Volume 30, Issue 4 Filling vacancies: Identifying the most efficient recruitment channel  

E-Print Network [OSTI]

Volume 30, Issue 4 Filling vacancies: Identifying the most efficient recruitment behaviour of firms by showing that recruitment channels clearly affect the probability of filling a vacancy are specialized, in that private agencies are more efficient at filling skilled vacancies, whereas public agencies

Paris-Sud XI, Université de

216

Crossings and nestings of two edges 01-Fillings of moon polyominoes  

E-Print Network [OSTI]

Crossings and nestings of two edges 01-Fillings of moon polyominoes Two generalizations Wang, Yan & Yeh Symmetry of 2-chains #12;Crossings and nestings of two edges 01-Fillings of moon polyominoes Two generalizations Outline 1 Crossings and nestings of two edges 2 01-Fillings of moon

217

Crossings and nestings of two edges 01-Fillings of moon polyominoes  

E-Print Network [OSTI]

Crossings and nestings of two edges 01-Fillings of moon polyominoes Two generalizations Symmetry of 2-chains #12;Crossings and nestings of two edges 01-Fillings of moon polyominoes Two generalizations Outline 1 Crossings and nestings of two edges 2 01-Fillings of moon polyominoes 3 Two

218

Vitrification of waste with conitnuous filling and sequential melting  

DOE Patents [OSTI]

A method of filling a canister with vitrified waste starting with a waste, such as high-level radioactive waste, that is cooler than its melting point. Waste is added incrementally to a canister forming a column of waste capable of being separated into an upper zone and a lower zone. The minimum height of the column is defined such that the waste in the lower zone can be dried and melted while maintaining the waste in the upper zone below its melting point. The maximum height of the column is such that the upper zone remains porous enough to permit evolved gases from the lower zone to flow through the upper zone and out of the canister. Heat is applied to the waste in the lower zone to first dry then to raise and maintain its temperature to a target temperature above the melting point of the waste. Then the heat is applied to a new lower zone above the melted waste and the process of adding, drying and melting the waste continues upward in the canister until the entire canister is filled and the entire contents are melted and maintained at the target temperature for the desired period. Cooling of the melted waste takes place incrementally from the bottom of the canister to the top, or across the entire canister surface area, forming a vitrified product.

Powell, James R. (Shoreham, NY); Reich, Morris (Kew Gardens Hills, NY)

2001-09-04T23:59:59.000Z

219

Improved gas mixtures for gas-filled radiation detectors  

DOE Patents [OSTI]

Improved binary and ternary gas mixtures for gas-filled radiation detectors are provided. The components are chosen on the basis of the principle that the first component is one molecular gas or mixture of two molecular gases having a large electron scattering cross section at energies of about 0.5 eV and higher, and the second component is a noble gas having a very small cross section at and below about 1.0 eV, whereby fast electrons in the gaseous mixture are slowed into the energy range of about 0.5 eV where the cross section for the mixture is small and hence the electron mean free path is large. The reduction in both the cross section and the electron energy results in an increase in the drift velocity of the electrons in the gas mixtures over that for the separate components for a range of E/P (pressure-reduced electric field) values. Several gas mixtures are provided that provide faster response in gas-filled detectors for convenient E/P ranges as compared with conventional gas mixtures.

Christophorou, L.G.; McCorkle, D.L.; Maxey, D.V.; Carter, J.G.

1980-03-28T23:59:59.000Z

220

Development of By-Pass Blending Station System  

E-Print Network [OSTI]

A new building blending station system named by-pass blending station (BBS) has been developed to reduce building pump energy consumption in both district heating and cooling systems. Theoretical investigation demonstrated that the BBS can...

Liu, M.; Barnes, D.; Bunz, K.; Rosenberry, N.

2003-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Fact #816: February 10, 2014 Natural Gas Refueling Stations Grow...  

Broader source: Energy.gov (indexed) [DOE]

6: February 10, 2014 Natural Gas Refueling Stations Grow Over the Last Ten Years Fact 816: February 10, 2014 Natural Gas Refueling Stations Grow Over the Last Ten Years In 2003...

222

Geothermal system saving money at fire station | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Geothermal system saving money at fire station Geothermal system saving money at fire station April 9, 2010 - 3:45pm Addthis Joshua DeLung What will the project do? A geothermal...

223

Central Station DHC Phase 1 feasibility  

SciTech Connect (OSTI)

This project assisted a private real estate developer in technically assessing the feasibility of integrating a central DHC system into a proposed 72 acre area mixed-use Planned Development (Central Station) just south of the Chicago Central Business District (Loop). The technical assessment concluded that a district heating and cooling system for Central Station will be feasible, provided that a major anchor load can be connected to the system. The system conceived for the site employs a modular approach that adjusts production capacity to actual load growth. The design concept includes gas-fired boilers for heating, gas turbine driven chillers for base loading, electric motor driven chillers for peaking, steam turbines for peak power and back pressure operation, and chilled water storage. Energy will be supplied to the users in the form of steam or low temperature hot water for heating, and low temperature chilled water for cooling.

Henderson, H.L.

1992-03-01T23:59:59.000Z

224

Small SDI battle stations - More is better  

SciTech Connect (OSTI)

It is presently suggested that large numbers of lower capability SDI systems, in contrast to small numbers of large battle stations, offer better overall defense performance at lower total cost, with lower technical risk, lower sensitivity to threat scenario variability, and improved survivability. This follows from such factors as the positioning of more platforms within effective range of targets during all phases of an attack, less exacting optics requirements, mass production economies-of-scale, and improved survivability.

Cornet, E.

1986-09-01T23:59:59.000Z

225

Improving Unit Operations-Test Station Performance  

E-Print Network [OSTI]

IMPROVING UNIT OPERATIONS - TEST STATION PERFORMANCE JosqIb 1. Filak. Jr, ? Corporate Energy Manager. Park.er?Hannafin COfpontioo- Cleveland. Oh ABSTRACT: This program's basic concept deals with the possibilities for reducing energy efficiency... requirements, control operation test performance functions more successfully, and retain peak load surges from reaching higher utility rate expense levels. 142 ESL-IE-95-04-23 Proceedings from the Seventeenth Industrial Energy Technology Conference...

Filak, J. J. Jr.

226

Xcel Energy Comanche Station: Pueblo, Colorado (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

A partnership with industry and U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to collect solar data to support future solar power generation in the United States. The measurement station monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location. The solar measurement instrumentation is also accompanied by meteorological monitoring equipment to provide scientists with a complete picture of the solar power possibilities.

Stoffel, T.; Andreas, A.

227

Manuel pour installer une station sismologique OSIRIS  

E-Print Network [OSTI]

installation Tout d'abord, enterrer le sismom`etre, s'assurer de l'horizontalit´e du sismo c'est-`a-dire, bulle le c^able sur le sismo, v´erifier de nouveau l'horizontalit´e. GPS Batterie ` Station d "sismo" puis cd osiris puis ./nrtd -set eth0 #12;7- Lancer Firefox (web browser) depuis la barre de menu

Perrot, Julie

228

Competitive Charging Station Pricing for Plug-in Electric Vehicles  

E-Print Network [OSTI]

. To overcome this challenge, we develop a low-complexity algorithm that efficiently computes the pricingCompetitive Charging Station Pricing for Plug-in Electric Vehicles Wei Yuan, Member, IEEE, Jianwei considers the problem of charging station pricing and station selection of plug-in electric vehicles (PEVs

Huang, Jianwei

229

"Space Station" Theme: Learning to Work, and Live, in Space  

E-Print Network [OSTI]

"Space Station" IMAX Film Theme: Learning to Work, and Live, in Space The educational value of NASM visit and afterward. See the "Alignment with Standards" table for details regarding how "Space Station in the "Space Station" program: · How astronauts train · What it is like to live and work in Space aboard

Mathis, Wayne N.

230

Optimization of compression and storage requirements at hydrogen refueling stations.  

SciTech Connect (OSTI)

The transition to hydrogen-powered vehicles requires detailed technical and economic analyses of all aspects of hydrogen infrastructure, including refueling stations. The cost of such stations is a major contributor to the delivered cost of hydrogen. Hydrogen refueling stations require not only dispensers to transfer fuel onto a vehicle, but also an array of such ancillary equipment as a cascade charging system, storage vessels, compressors and/or pumps/evaporators. This paper provides detailed information on design requirements for gaseous and liquid hydrogen refueling stations and their associated capital and operating costs, which in turn impact hydrogen selling price at various levels of hydrogen demand. It summarizes an engineering economics approach which captures the effect of variations in station size, seasonal, daily and hourly demand, and alternative dispensing rates and pressures on station cost. Tradeoffs in the capacity of refueling station compressors, storage vessels, and the cascade charging system result in many possible configurations for the station. Total costs can be minimized by optimizing that configuration. Using a methodology to iterate among the costs of compression, storage and cascade charging, it was found that the optimum hourly capacity of the compressor is approximately twice the station's average hourly demand, and the optimum capacity of the cascade charging system is approximately 15% of the station's average daily demand. Further, for an hourly demand profile typical of today's gasoline stations, onsite hydrogen storage equivalent to at least 1/3 of the station's average daily demand is needed to accommodate peak demand.

Elgowainy, A.; Mintz, M.; Kelly, B.; Hooks, M.; Paster, M. (Energy Systems); (Nexant, Inc.); (TIAX LLC)

2008-01-01T23:59:59.000Z

231

Plug-In Electric Vehicle Handbook for Public Charging Station Hosts (Brochure)  

SciTech Connect (OSTI)

This handbook answers basic questions about plug-in electric vehicles, charging stations, charging equipment, and considerations for station owners, property owners, and station hosts.

Not Available

2012-04-01T23:59:59.000Z

232

Environmental Assessment for the Warren Station externally fired combined cycle demonstration project  

SciTech Connect (OSTI)

The proposed Penelec project is one of 5 projects for potential funding under the fifth solicitation under the Clean Coal Technology program. In Penelec, two existing boilers would be replaced at Warren Station, PA; the new unit would produce 73 MW(e) in a combined cycle mode (using both gas-fired and steam turbines). The project would fill the need for a full utility-size demonstration of externally fire combined cycle (EFCC) technology as the next step toward commercialization. This environmental assessment was prepared for compliance with NEPA; its purpose is to provide sufficient basis for determining whether to prepare an environmental impact statement or to issue a finding of no significant impact. It is divided into the sections: purpose and need for proposed action; alternatives; brief description of affected environment; environmental consequences, including discussion of commercial operation beyond the demonstration period.

NONE

1995-04-01T23:59:59.000Z

233

Fast ultrasonic imaging in a liquid filled pipe  

SciTech Connect (OSTI)

A new method is described for the imaging of the interior of a liquid filled metallic pipe using acoustical techniques. The experimental system incorporates an array of 20 acoustical transducers and is capable of capturing the images of moving bubbles at a frame rate in excess of 300/s. The transducers are mounted circumferentially around the pipe. Each transducer is pulsed in sequence, and the echoes reflected from vapor bubbles in the interior are detected, digitized and processed by a computer to generate an image. The high rate of speed was achieved by the use of newly developed software and electronic circuitry. This approach has eliminated most of the spurious echo signals which degraded the performance of previous imaging systems. The capability of the method is illustrated by imaging actual vapor bubbles in rapid sequence in the pipe. 13 refs.

Kolbe, W.F.; Turko, B.T.; Leskovar, B.

1985-10-01T23:59:59.000Z

234

COMSOL MULTIPHYSICS MODEL FOR DWPF CANISTER FILLING, REVISION 1  

SciTech Connect (OSTI)

This revision is an extension of the COMSOL Multiphysics model previously developed and documented to simulate the temperatures of the glass during pouring a Defense Waste Processing Facility (DWPF) canister. In that report the COMSOL Multiphysics model used a lumped heat loss term derived from experimental thermocouple data based on a nominal pour rate of 228 lbs./hr. As such, the model developed using the lumped heat loss term had limited application without additional experimental data. Therefore, the COMSOL Multiphysics model was modified to simulate glass pouring and subsequent heat input which, replaced the heat loss term in the initial model. This new model allowed for changes in flow geometry based on pour rate as well as the ability to increase and decrease flow and stop and restart flow to simulate varying process conditions. A revised COMSOL Multiphysics model was developed to predict temperatures of the glass within DWPF canisters during filling and cooldown. The model simulations and experimental data were in good agreement. The largest temperature deviations were {approx} 40 C for the 87 inch thermocouple location at 3000 minutes and during the initial cool down at the 51 inch location occurring at approximately 600 minutes. Additionally, the model described in this report predicts the general temperature trends during filling and cooling as observed experimentally. The revised model incorporates a heat flow region corresponding to the glass pouring down the centerline of the canister. The geometry of this region is dependent on the flow rate of the glass and can therefore be used to see temperature variations for various pour rates. The equations used for this model were developed by comparing simulation output to experimental data from a single pour rate. Use of the model will predict temperature profiles for other pour rates but the accuracy of the simulations is unknown due to only a single flow rate comparison.

Kesterson, M.

2011-09-08T23:59:59.000Z

235

Network Chimera Network Chimera  

E-Print Network [OSTI]

Network Chimera Network Chimera Objective Chimera aims to understand how the network properties enough with limited resources. The Chimera team is cross-disciplinary, and includes computer scientists Impact The original hypothesis of Chimera was that a physical network could be reduced to a graph

236

Kansas City`s Union Station redevelopment opportunity -- Environmental challenges  

SciTech Connect (OSTI)

Kansas City`s Union Station, located at the center of a 1.7 million metropolitan population, is the second largest train station in the United States. The Station ceased to operate as a train station in 1983 and has since been falling into an increasing state of disrepair. This paper provides an insight into ``brownfield`` redevelopment and renovation for adaptive reuse of major turn of the century facilities such as Union Station. Substantial assessment and investigation activities have been conducted at Union Station for compliance and corrective action under RCRA, TSCA, and associated state regulations encompassing remediation estimated at more than $3 million. Recognized environmental conditions identified at Union Station included potential underground storage tanks; solid wastes, special wastes, and potentially hazardous wastes located inside the building; free liquids in sumps and elevator pits; asbestos-containing materials; lead-based paint; and potential for soil contamination on the surrounding property.

Snyder, M.G. [Black and Veatch Waste Science, Inc., Overland Park, KS (United States); Scott, A. [Union Station Assistance Corp., Kansas City, MO (United States)

1995-12-31T23:59:59.000Z

237

Page 1 of 2 STATE OF CALIFORNIA NATURAL RESOURCES AGENCY EDMUND G. BROWN JR., Governor  

E-Print Network [OSTI]

Hydrogen Frontier's "Hydrogen Fueling Stations" o Huntington Beach Station on Main Street o Lake Forest Hydrogen Station on Lake Forest Drive Air Products and Chemicals, Inc.'s "Low Cost Hydrogen Refueling Station Network Deployment" o Wilmington Fill System on Henry Ford Avenue o Beverly Hills Station

238

Sandia National Laboratories: Reference Station Design  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassive SolarEducationStationCSPRecovery Act Solar Test Facility Upgrades

239

Husavik Geothermal Power Station | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat Jump to:PhotonHolyName HousingIII Wind FarmWouldOpenSchools JumpStation

240

E-Print Network 3.0 - ath filled epdm Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Mathematics 11 TR 353 EVALUATION OF CANAL LINING PROJECTS Summary: of Texas: polyester PVC polypropylene PVC alloy EPDM rubber polyurethane Table 1... ....

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

aluminium foam-filled sections: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

compressed sensing maps M : RN Rk (for k to compressed sensing Subspaces from expanderTanner codes Constant distortion construction Explicit Randriam, Hugues...

242

E-Print Network 3.0 - alloy filling technology Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

STRESSES DURING CASTING OF BINARY MAGNESIUM-ALUMINUM ALLOYS M.G. Pokorny1 , C... , Geesthacht, Germany Keywords: Magnesium Alloys, Casting, Stress Simulation Abstract A visco......

243

E-Print Network 3.0 - air-filled triangular enclosure Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

enclosures and compares them with numerical... ... 2 2. Heat transfer correlations for vertical enclosures ... Source: United States Army Corps of...

244

alkali-metal vapor-filled ceramic: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

j and the magnetic field H in Bi2Sr2CaCu2O8 x ceramics. We provided in high-Tc superconduct- ing granular ceramics remain an intriguing subject of inten- sive investigations...

245

alluvial basin-fill deposits: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

facies changes that result (more) Turner, Alexandre Marcel 2014-01-01 74 A Radon Progeny Deposition Model Nuclear Experiment (arXiv) Summary: The next generation...

246

E-Print Network 3.0 - ar filled metallic Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

A detailed analysis of the formation energies for alkali, earth-alkali, and transition-metal Source: Marianetti, Chris A. - Department of Applied Physics and Applied Mathematics,...

247

E-Print Network 3.0 - ash flowable fill Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Utilization Summary: ash as filler. A highly flowable concrete is not necessarily self-compacting because SCC should... ;4. Kurita, M., and Nomura, T., "High-Flowable Steel...

248

E-Print Network 3.0 - ar gas filled Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and the origin of carbonatites Summary: gas abundance ratios (for example HeAr and CO2 Ar), which change upon degassing owing to solubility... 36 Ar against 40 Ar36 Ar for...

249

Report on Experiments with Citrus Fruits at the Beeville Sub-station.  

E-Print Network [OSTI]

!TEXAS AGRICULTURAL EXPERIMENT STATIONS BULLETIN No. 148. MAY, 1912. Report on Experiments With Citrus Fruits at The Bee- ville Sub-station A. T. POTTS, Superintendent Beeville Sub-station AUSTIN PRINTING COMPANY AUSTIN. TEXAS TEXAS... EXPERIMENT STATIONS. GOVERNING BOARD. 1 DIRECTOR OF STATIONS. ...................................... B. YOUNOBLOOD, M. S.. .College Station I SUPERINTENDENTS OF SUB-STATIONS. .................. E. E. BINFORD, Beeville Sub-station.. .Beeville, P:.e Cc...

Potts, A. T. (Arthur Tillman)

1912-01-01T23:59:59.000Z

250

SEAD: secure efficient distance vector routing for mobile wireless ad hoc networks  

E-Print Network [OSTI]

SEAD: secure efficient distance vector routing for mobile wireless ad hoc networks Yih-Chun Hu a University, Houston, TX 77005, USA Abstract An ad hoc network is a collection of wireless computers (nodes stations or access points. Although many previous ad hoc network routing protocols have been based in part

Ramkumar, Mahalingam

251

Optimization of Wireless Access Point Placement in Realistic Urban Heterogeneous Networks  

E-Print Network [OSTI]

for irregular heterogeneous networks with hierarchical APs such as macro/micro base-stations, picoOptimization of Wireless Access Point Placement in Realistic Urban Heterogeneous Networks Yicheng network under a given user geographic distribution, and proposes an iterative method to optimize

Yu, Wei

252

Modeling energy consumption in cellular networks L. Decreusefond  

E-Print Network [OSTI]

Modeling energy consumption in cellular networks L. Decreusefond Telecom Paristech, LTCI Paris Abstract--In this paper we present a new analysis of energy consumption in cellular networks. We focus on the distribution of energy consumed by a base station for one isolated cell. We first define the energy consumption

Boyer, Edmond

253

National Seismological Network HIS MAJESTY'S GOVERNMENT OF NEPAL  

E-Print Network [OSTI]

National Seismological Network HIS MAJESTY'S GOVERNMENT OF NEPAL Lainchour Kathmandu, Nepal March the establishment of Nepal's first seismic station at Phulchoki, Kathmandu in November, 1978 by the Department hazard assessment in the Nepal Himalaya. The network provides routine information on global seismicity

Avouac, Jean-Philippe

254

APAWSAN: Actor Positioning for Aerial Wireless Sensor and Actor Networks  

E-Print Network [OSTI]

to be autonomous during deployment. The recent advances in development of small unmanned aerial vehicles (UAVs stations can improve network performance measures such as energy consumption and traffic load balancing vehicles (UAVs) with built in sensors made it possible to deploy aerial sensor and actor networks

Turgut, Damla

255

Wormhole-Resilient Secure Neighbor Discovery in Underwater Acoustic Networks  

E-Print Network [OSTI]

), Unmanned Underwater Vehicles (UUV), and surface stations, and nearby nodes communicate via acoustic ratherWormhole-Resilient Secure Neighbor Discovery in Underwater Acoustic Networks Rui Zhang and Yanchao in underwater acoustic networks (UANs) with floating node mobility. In hostile environments, neighbor discovery

Zhang, Rui

256

The University of Wisconsin-Milwaukee Field Station The Field Station is celebrating its 50th  

E-Print Network [OSTI]

land, until today the Field Station has grown into an active, vibrant facility with many projects for experimental research. Growth of our facilities has been funded by the National Science Foundation Bat Hibernaculum, an abandoned iron mine in Dodge County that is one of the largest sites

Saldin, Dilano

257

Webinar: Guidance for Filling Out a Detailed H2A Production Case Study  

Broader source: Energy.gov [DOE]

Video recording and text version of the webinar titled, Guidance for Filling Out a Detailed H2A Production Case Study, originally presented on July 9, 2013.

258

Magnetism and superconductivi[t]y in Pr-based filled skutterudite arsenides  

E-Print Network [OSTI]

1.5 Superconductivity . . . . . . . . . . . . . . . . . . .and M. B. Maple, ”Superconductivity and non-Fermi liquidSAN DIEGO Magnetism and Superconductiviy in Pr-based Filled

Sayles, Todd Allen

2008-01-01T23:59:59.000Z

259

Slow Waves in Fractures Filled with Viscous Fluid  

SciTech Connect (OSTI)

Stoneley guided waves in a fluid-filled fracture generally have larger amplitudes than other waves, and therefore, their properties need to be incorporated in more realistic models. In this study, a fracture is modeled as an infinite layer of viscous fluid bounded by two elastic half-spaces with identical parameters. For small fracture thickness, I obtain a simple dispersion equation for wave-propagation velocity. This velocity is much smaller than the velocity of a fluid wave in a Biot-type solution, in which fracture walls are assumed to be rigid. At seismic prospecting frequencies and realistic fracture thicknesses, the Stoneley guided wave has wavelengths on the order of several meters and an attenuation Q factor exceeding 10, which indicates the possibility of resonance excitation in fluid-bearing rocks. The velocity and attenuation of Stoneley guided waves are distinctly different at low frequencies for water and oil. The predominant role of fractures in fluid flow at field scales is supported by permeability data showing an increase of several orders of magnitude when compared to values obtained at laboratory scales. These data suggest that Stoneley guided waves should be taken into account in theories describing seismic wave propagation in fluid-saturated rocks.

Korneev, Valeri

2008-01-08T23:59:59.000Z

260

Fluid-filled bomb-disrupting apparatus and method  

DOE Patents [OSTI]

An apparatus and method for disarming improvised bombs are disclosed. The apparatus comprises a fluid-filled bottle or container made of plastic or another soft material which contains a fixed or adjustable, preferably sheet explosive. The charge is fired centrally at its apex and can be adjusted to propel a fluid projectile that is broad or narrow, depending upon how it is set up. In one embodiment, the sheet explosive is adjustable so as to correlate the performance of the fluid projectile to the disarming needs for the improvised explosive device (IED). Common materials such as plastic water bottles or larger containers can be used, with the sheet explosive or other explosive material configured in a general chevron-shape to target the projectile toward the target. In another embodiment, a thin disk of metal is conformably mounted with the exterior of the container and radially aligned with the direction of fire of the fluid projectile. Depending on the configuration and the amount of explosive and fluid used, a projectile is fired at the target that has sufficient energy to penetrate rigid enclosures from fairly long stand-off and yet is focused enough to be targeted to specific portions of the IED for disablement.

Cherry, Christopher R. (Albuquerque, NM)

2001-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Chaotic vibration of a liquid-filled thin cylindrical shell  

SciTech Connect (OSTI)

Recently, a large number of thin walled cylindrical tanks have been widely used, such as oil-storage tanks, and LMFBR primary components. To assess the safety of these systems against earthquakes, it is of great technical importance to clarify the fluid-coupled vibration characteristics of the systems subjected to certain kinds of dynamic loads. This paper describes an experimental study on the chaos of a partially liquid-filled cylindrical tank under horizontal excitation. The test cylinder with a mean radius of 170 mm was made of polyester film with a nominal thickness of 0.188 mm which was lap-joined along a longitudinal seam and bonded with an aluminum end plate along one edge. Shaking table tests were conducted in order to investigate the dynamic characteristics of the shell response. Several types of limit cycles were observed at lower accelerations, and the instability phenomenon, which jumped at some excitation frequencies, occurred for acceleration amplitudes above a critical value. Finally, at higher excitation accelerations, the shell responses became chaotic. The occurrence of the chaos was recognized by the time history, Poincare map, phase trajectory, power spectrum and a positive Lyapunov exponent calculated from the orbits in the three dimensional phase space. In order to visualize the strange attractor, phase portraits were constructed by embedding the trajectories in the phase space.

Toyoda, Y.; Masuko, Y. [Central Research Inst. of Electric Power Industry, Abiko, Chiba (Japan). Abiko Research Lab.

1996-12-01T23:59:59.000Z

262

New solar axion search in CAST with $^4$He filling  

E-Print Network [OSTI]

The CERN Axion Solar Telescope (CAST) searches for $a\\to\\gamma$ conversion in the 9 T magnetic field of a refurbished LHC test magnet that can be directed toward the Sun. Two parallel magnet bores can be filled with helium of adjustable pressure to match the X-ray refractive mass $m_\\gamma$ to the axion search mass $m_a$. After the vacuum phase (2003--2004), which is optimal for $m_a\\lesssim0.02$ eV, we used $^4$He in 2005--2007 to cover the mass range of 0.02--0.39 eV and $^3$He in 2009--2011 to scan from 0.39--1.17 eV. After improving the detectors and shielding, we returned to $^4$He in 2012 to investigate a narrow $m_a$ range around 0.2 eV ("candidate setting" of our earlier search) and 0.39--0.42 eV, the upper axion mass range reachable with $^4$He, to "cross the axion line" for the KSVZ model. We have improved the limit on the axion-photon coupling to $g_{a\\gamma}< 1.47\\times10^{-10} {\\rm GeV}^{-1}$ (95% C.L.), depending on the pressure settings. Since 2013, we have returned to vacuum and aim for a significant increase in sensitivity.

M. Arik; S. Aune; K. Barth; A. Belov; H. Bräuninger; J. Bremer; V. Burwitz; G. Cantatore; J. M. Carmona; S. A. Cetin; J. I. Collar; E. Da Riva; T. Dafni; M. Davenport; A. Dermenev; C. Eleftheriadis; N. Elias; G. Fanourakis; E. Ferrer-Ribas; J. Galán; J. A. García; A. Gardikiotis; J. G. Garza; E. N. Gazis; T. Geralis; E. Georgiopoulou; I. Giomataris; S. Gninenko; M. Gómez Marzoa; M. D. Hasinoff; D. H. H. Hoffmann; F. J. Iguaz; I. G. Irastorza; J. Jacoby; K. Jakov?i?; M. Karuza; M. Kavuk; M. Kr?mar; M. Kuster; B. Laki?; J. M. Laurent; A. Liolios; A. Ljubi?i?; G. Luzón; S. Neff; T. Niinikoski; A. Nordt; I. Ortega; T. Papaevangelou; M. J. Pivovaroff; G. Raffelt A. Rodríguez; M. Rosu; J. Ruz; I. Savvidis; I. Shilon; S. K. Solanki; L. Stewart; A. Tomás; T. Vafeiadis; J. Villar; J. K. Vogel; S. C. Yildiz; K. Zioutas

2015-03-02T23:59:59.000Z

263

New solar axion search in CAST with $^4$He filling  

E-Print Network [OSTI]

The CERN Axion Solar Telescope (CAST) searches for $a\\to\\gamma$ conversion in the 9 T magnetic field of a refurbished LHC test magnet that can be directed toward the Sun. Two parallel magnet bores can be filled with helium of adjustable pressure to match the X-ray refractive mass $m_\\gamma$ to the axion search mass $m_a$. After the vacuum phase (2003--2004), which is optimal for $m_a\\lesssim0.02$ eV, we used $^4$He in 2005--2007 to cover the mass range of 0.02--0.39 eV and $^3$He in 2009--2011 to scan from 0.39--1.17 eV. After improving the detectors and shielding, we returned to $^4$He in 2012 to investigate a narrow $m_a$ range around 0.2 eV ("candidate setting" of our earlier search) and 0.39--0.42 eV, the upper axion mass range reachable with $^4$He, to "cross the axion line" for the KSVZ model. We have improved the limit on the axion-photon coupling to $g_{a\\gamma}< 1.47\\times10^{-10} {\\rm GeV}^{-1}$ (95% C.L.), depending on the pressure settings. Since 2013, we have returned to vacuum and aim for a s...

Arik, M; Barth, K; Belov, A; Brauninger, H; Bremer, J; Burwitz, V; Cantatore, G; Carmona, J M; Cetin, S A; Collar, J I; Da Riva, E; Dafni, T; Davenport, M; Dermenev, A; Eleftheriadis, C; Elias, N; Fanourakis, G; Ferrer-Ribas, E; Galan, J; Garcia, J A; Gardikiotis, A.; Garza, J G; Gazis, E N; Geralis, T; Georgiopoulou, E; Giomataris, I; Gninenko, S; Marzoa, M Gomez; Hasinoff, M D; Hoffmann, D H H; Iguaz, F J; Irastorza, I G; Jacoby, J; K.Jakovcic; Karuza, M; Kavuk, M; Krcmar, M; Kuster, M; Lakic, B; Laurent, J M; Liolios, A; Ljubicic, A; Luzon, G; Neff, S; Niinikoski, T; Nordt, A; Ortega, I; Papaevangelou, T; Pivovaroff, M .J; Raffelt, G; Rodriguez, A; Rosu, M; Ruz, J; Savvidis, I; Shilon, I; Solanki, S K; Stewart, L; Tomas, A; Vafeiadis, T; Villar, J; Vogel, J K; Yildiz, S C; Zioutas, K

2015-01-01T23:59:59.000Z

264

New Jersey Nuclear Profile - PSEG Salem Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

PSEG Salem Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

265

California Nuclear Profile - San Onofre Nuclear Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

San Onofre Nuclear Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

266

New Jersey Nuclear Profile - PSEG Hope Creek Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

PSEG Hope Creek Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

267

Illinois Nuclear Profile - LaSalle Generating Station  

U.S. Energy Information Administration (EIA) Indexed Site

LaSalle Generating Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License expiration...

268

New York Nuclear Profile - Nine Mile Point Nuclear Station  

U.S. Energy Information Administration (EIA) Indexed Site

Nine Mile Point Nuclear Station" "Unit","Summer capacity (mw)","Net generation (thousand mwh)","Summer capacity factor (percent)","Type","Commercial operation date","License...

269

Electric Vehicle Charging Stations, Coming Soon to a City Near...  

Broader source: Energy.gov (indexed) [DOE]

to be available throughout the Orlando area next year. File photo Orlando Plugs into Electric Vehicle Charging Stations Assistant Secretary Patricia Hoffman test drives the...

270

Investigations of Sediment Elutriate Toxicity at Three Estuarine Stations  

E-Print Network [OSTI]

Investigations of Sediment Elutriate Toxicity at Three Estuarine Stations in San Francisco Bay.............................................................................................. 8 Sediment-Water Interface Exposures................................................................................. 9 August 1997 Sediment-Water Interface Exposures

271

Microgrid V2G Charging Station Interconnection Testing (Presentation)  

SciTech Connect (OSTI)

This presentation by Mike Simpson of the National Renewable Energy Laboratory (NREL) describes NREL's microgrid vehicle-to-grid charging station interconnection testing.

Simpson, M.

2013-07-01T23:59:59.000Z

272

Sandia National Laboratories: More California Gas Stations Can...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

than Previously Thought, Sandia Study Says More California Gas Stations Can Provide Hydrogen than Previously Thought, Sandia Study Says Diamond Plates Create Nanostructures...

273

The Fuel-Travel-Back Approach to Hydrogen Station Siting  

E-Print Network [OSTI]

costs of cars with alternative fuels/engines." Energy Policyto the Choice of Alternative Fuels and Vehicles." Energyhydrogen; station location; alternative fuel; optimization

Lin, Zhenhong; Ogden, Joan; Fan, Yueyue; Chen, Chien-Wei

2009-01-01T23:59:59.000Z

274

Columbia Generating Station debt options for rate relief - November...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

extending about 350 million of existing Columbia Generating Station debt to 2024 to the Energy Northwest Audit, Legal and Finance Committee (www.bpa.govcorporateFinanceDebt...

275

Design of Photovoltaics e-bikes charging station:.  

E-Print Network [OSTI]

??It is a project about designing a photovoltaics charging station for electrical bikes and scooters, which can facilitate electrical bike user and promote sustainable way… (more)

Zhao, Y.

2014-01-01T23:59:59.000Z

276

Solar Powered Radioactive Air Monitoring Stations  

SciTech Connect (OSTI)

Environmental monitoring of ambient air for radioactive material is required as stipulated in the PNNL Site radioactive air license. Sampling ambient air at identified preferred locations could not be initially accomplished because utilities were not readily available. Therefore, solar powered environmental monitoring systems were considered as a possible option. PNNL purchased two 24-V DC solar powered environmental monitoring systems which consisted of solar panels, battery banks, and sampling units. During an approximate four month performance evaluation period, the solar stations operated satisfactorily at an on-site test location. They were subsequently relocated to their preferred locations in June 2012 where they continue to function adequately under the conditions found in Richland, Washington.

Barnett, J. M.; Bisping, Lynn E.; Gervais, Todd L.

2013-10-30T23:59:59.000Z

277

A Hybrid Testbed for a Seamless Combination of Wireless Sensor Networks and OMNeT++ Simulations  

E-Print Network [OSTI]

to control heliostats of a solar power plant. For this purpose a base station ei- ther communicates these execution environments can seamlessly be interconnected to a virtual, homogeneous network. This provides

Turau, Volker

278

First Draft 06/05/13 Definitions of Relevant Terms for the Observation Network and Fixed  

E-Print Network [OSTI]

reveals quality assurance checks, and the Map tab takes you to the map of the endurance stations which on norms, principles, values, and rules. The Science and Technology University Research Network (SATURN

279

An Energy-Efficient Power Allocation Game with Selfish Channel State Reporting in Cellular Networks  

E-Print Network [OSTI]

An Energy-Efficient Power Allocation Game with Selfish Channel State Reporting in Cellular Networks With energy-efficient resource allocation, mobile users and base station have different objectives. While the base station strives for an energy-efficient operation of the complete cell, each user aims to maximize

Boyer, Edmond

280

Inspection of the establishment and filling of the Department`s Ombudsman position  

SciTech Connect (OSTI)

This report gives the findings and recommendations following the review of possible personnel irregularities regarding the establishment and filling of the position of DOE Departmental Conflict Resolution Ombudsman (Departmental Ombudsman) and possible irregularities regarding the payment of per diem to the individual selected to fill this position.

NONE

1996-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Electric Vehicle Charging in Smart Grid: Optimality and Valley-filling Algorithms  

E-Print Network [OSTI]

different settings. Index Terms--Optimal power flow, electric vehicle charging, valley-filling, onlineForReview Only 1 Electric Vehicle Charging in Smart Grid: Optimality and Valley-filling Algorithms, IEEE. Abstract--Electric vehicles (EVs) offer an attractive long-term solution to reduce the dependence

Tan, Chee Wei

282

The Mechanical Coupling of Fluid-Filled Granular Material Under Shear  

E-Print Network [OSTI]

The Mechanical Coupling of Fluid-Filled Granular Material Under Shear L. Goren*, E. Aharonov and University of Strasbourg (EOST), Strasbourg, France. Abstract. The coupled mechanics of fluid-filled granular the mechanical strength of the grains skeleton? To answer these questions, a formulation for the pore fluid

Paris-Sud XI, Université de

283

Paper Number 05 Structural Fuses and Concrete-Filled Steel Shapes for  

E-Print Network [OSTI]

Paper Number 05 Structural Fuses and Concrete-Filled Steel Shapes for Seismic- and Multi-hazard design concepts. This paper presents recent research on structural fuses and concrete-filled steel shapes composite rectangular columns of Bi-Steel panels. Experimental results from another series of tests

Bruneau, Michel

284

Slow waves in fractures filled with viscous fluid Valeri Korneev1  

E-Print Network [OSTI]

Slow waves in fractures filled with viscous fluid Valeri Korneev1 ABSTRACT Stoneley guided waves in a fluid-filled fracture generally have larger amplitudes than other waves; therefore, their properties, a simple dispersion equa- tion for wave-propagation velocity is obtained. This velocity is much smaller

Korneev, Valeri A.

285

Scaling Dynamics of a Massive Piston in a Cube Filled With Ideal Gas: Exact Results  

E-Print Network [OSTI]

Scaling Dynamics of a Massive Piston in a Cube Filled With Ideal Gas: Exact Results N. Chernov1 65th birthday Abstract We continue the study of the time evolution of a system consisting of a piston in a cubical container of large size L filled with an ideal gas. The piston has mass M L2 and undergoes

Lebowitz, Joel

286

Scaling Dynamics of a Massive Piston in a Cube Filled With Ideal Gas: Exact Results  

E-Print Network [OSTI]

Scaling Dynamics of a Massive Piston in a Cube Filled With Ideal Gas: Exact Results N. Chernov 1 of a piston in a cubical container of large size L filled with an ideal gas. The piston has mass M # L 2 heuristically that the motion of the piston and the one particle distribution of the gas satisfy autonomous

287

On the editing of images: selecting, cutting and filling-in  

E-Print Network [OSTI]

On the editing of images: selecting, cutting and filling-in Fr´ed´eric Labrosse Computer Science: selecting, cutting and filling-in Fr´ed´eric Labrosse Computer Science Department, University of Wales of this work is post-production special effects in cinema or image manipulation where one often wants to remove

Labrosse, Frédéric

288

FILLING OF METHANE/AIR MIXTURE IN A TUBE FOR PULSE DETONATION ENGINES SHRAVANI DWARAKAPALLY  

E-Print Network [OSTI]

FILLING OF METHANE/AIR MIXTURE IN A TUBE FOR PULSE DETONATION ENGINES By SHRAVANI DWARAKAPALLY. Thanks to my god Lord Shiva for his blessings. November 18, 2011 #12;v ABSTRACT FILLING OF METHANE, was studied using the unsteady flow solver methane and air nominally at STP. Three cases were examined: (i

Texas at Arlington, University of

289

Cyclic Testing of Concrete-Filled Circular Steel Bridge Piers having Encased Fixed-Based Detail  

E-Print Network [OSTI]

Cyclic Testing of Concrete-Filled Circular Steel Bridge Piers having Encased Fixed-Based Detail elements during earthquakes, this paper reports on cyclic inelastic tests executed to determine the maximum strength and ductility of four concrete-filled circular steel piers joined to a foundation detail proposed

Bruneau, Michel

290

Project X Energy Station Workshop Report. Report by the Organizers and Co-Conveners of the Project X Energy Station Workshop  

SciTech Connect (OSTI)

Project X Energy Station Workshop Report Report by the Organizers and Co-Conveners of the Project X Energy Station Workshop

Asner, David M.; Hurh, Patrick; Brady Raap, Michaele C.; Gohar, Yoursy; Peterson, Mary E.; Pithcer, Eric; Riemer, Bernie; Senor, David J.; Wootan, David W.

2013-06-14T23:59:59.000Z

291

Final environmental assessment for vegetation control at VHF stations, microwave stations, electrical substations, and pole yards  

SciTech Connect (OSTI)

Southwestern Power Adm. operates very high frequency (VHF) and microwave radio stations, electrical substations, and pole yards for electric power transmission throughout AR, MO, and OK. Vegetation growth at the stations must be suppressed for safety of operation and personnel. Southwestern has been using a combination of mechanical/manual and herbicide control for this purpose; Federally- mandated reductions in staff and budgetary resources require Southwestern to evaluate all potentially efficient methods for vegetation control. Three alternatives were examined: no action, mechanical/manual control, and (proposed) a combination of mechanical/manual and herbicide control. Environmental impacts on air and water quality, wetlands, wildlife, endangered species, archaeological and other resources, farmland, human health, transportation, etc. were evaluated.

NONE

1995-10-13T23:59:59.000Z

292

Randomizing bipartite networks: the case of the World Trade Web  

E-Print Network [OSTI]

Within the last fifteen years, network theory has been successfully applied both to natural sciences and to socioeconomic disciplines. In particular, bipartite networks have been recognized to provide a particularly insightful representation of many systems, ranging from mutualistic networks in ecology to trade networks in economy, whence the need of a pattern detection-oriented analysis in order to identify statistically-significant structural properties. Such an analysis rests upon the definition of suitable null models, i.e. upon the choice of the portion of network structure to be preserved while randomizing everything else. However, quite surprisingly, little work has been done so far to define null models for real bipartite networks. The aim of the present work is to fill this gap, extending a recently-proposed method to randomize monopartite networks to bipartite networks. While the proposed formalism is perfectly general, we apply our method to the binary, undirected, bipartite representation of the W...

Saracco, Fabio; Gabrielli, Andrea; Squartini, Tiziano

2015-01-01T23:59:59.000Z

293

References Applicable to Station-Level Calibration Steve Ellingson  

E-Print Network [OSTI]

, W. Hocking, and F. Fabry, "Precipitation Measurement using VHF Wind-Profiler Radars: A MultifacetedReferences Applicable to Station-Level Calibration Steve Ellingson July 17, 2008 1 Summary This is a list of references possibly applicable to LWA station-level calibration. References [1] R.L. Balsano

Ellingson, Steven W.

294

Achieving High Chilled Water Delta T Without Blending Station  

E-Print Network [OSTI]

on the blending station performance. The results show that the blending station is not necessary in the building chilled water systems with 2-way modulation valves at end users. Actually the end user valve configuration and control mainly impacts building chilled...

Wang, Z.; Wang, G.; Xu, K.; Yu, Y.; Liu, M.

2007-01-01T23:59:59.000Z

295

Assessment of district energy supply from Schiller Generating Station  

SciTech Connect (OSTI)

This paper addresses the feasibility analysis of retrofitting the Public Service of New Hampshire Schiller Generating Station to supply district heating to potential customers. The project involved analysis of power plant retrofit and comparison of district heating cost to the cost of heat supplied with gas boilers for a housing development in close proximity to the Schiller Station.

Hitchko, M. [Public Service Company of New Hampshire, Portsmouth, NH (United States); Major, W. [Joseph Technology Corporation, Inc., Woodcliff Lake, NJ (United States)

1995-06-01T23:59:59.000Z

296

Validation of an Integrated Hydrogen Energy Station  

SciTech Connect (OSTI)

This report presents the results of a 10-year project conducted by Air Products and Chemicals, Inc. (Air Products) to determine the feasibility of coproducing hydrogen with electricity. The primary objective was to demonstrate the technical and economic viability of a hydrogen energy station using a high-temperature fuel cell designed to produce power and hydrogen. This four-phase project had intermediate go/no-go decisions and the following specific goals: �¢���¢ Complete a technical assessment and economic analysis of the use of high-temperature fuel cells, including solid oxide and molten carbonate, for the co-production of power and hydrogen (energy park concept). �¢���¢ Build on the experience gained at the Las Vegas H2 Energy Station and compare/contrast the two approaches for co-production. �¢���¢ Determine the applicability of co-production from a high-temperature fuel cell for the existing merchant hydrogen market and for the emerging hydrogen economy. �¢���¢ Demonstrate the concept on natural gas for six months at a suitable site with demand for both hydrogen and electricity. �¢���¢ Maintain safety as the top priority in the system design and operation. �¢���¢ Obtain adequate operational data to provide the basis for future commercial activities, including hydrogen fueling stations. Work began with the execution of the cooperative agreement with DOE on 30 September 2001. During Phase 1, Air Products identified high-temperature fuel cells as having the potential to meet the coproduction targets, and the molten carbonate fuel cell system from FuelCell Energy, Inc. (FuelCell Energy) was selected by Air Products and DOE following the feasibility assessment performed during Phase 2. Detailed design, construction and shop validation testing of a system to produce 250 kW of electricity and 100 kilograms per day of hydrogen, along with site selection to include a renewable feedstock for the fuel cell, were completed in Phase 3. The system also completed six months of demonstration operation at the wastewater treatment facility operated by Orange County Sanitation District (OCSD, Fountain Valley, CA). As part of achieving the objective of operating on a renewable feedstock, Air Products secured additional funding via an award from the California Air Resources Board. The South Coast Air Quality Management District also provided cost share which supported the objectives of this project. System operation at OCSD confirmed the results from shop validation testing performed during Phase 3. Hydrogen was produced at rates and purity that met the targets from the system design basis, and coproduction efficiency exceeded the 50% target set in conjunction with input from the DOE. Hydrogen production economics, updated from the Phase 2 analysis, showed pricing of $5 to $6 per kilogram of hydrogen using current gas purification systems. Hydrogen costs under $3 per kilogram are achievable if next-generation electrochemical separation technologies become available.

Edward C. Heydorn

2012-10-26T23:59:59.000Z

297

29.01.03.M1.12 Information Resources Network Access Page 1 of 3 STANDARD ADMINISTRATIVE PROCEDURE  

E-Print Network [OSTI]

29.01.03.M1.12 Information Resources ­ Network Access Page 1 of 3 STANDARD ADMINISTRATIVE PROCEDURE Administrative Procedure Statement The information resources network infrastructure in Bryan/College Station for SAP The purpose of this Texas A&M University network access standard administrative procedure

298

Compression station key to Texas pipeline project  

SciTech Connect (OSTI)

This was probably the largest pipeline project in the US last year, and the largest in Texas in the last decade. The new compressor station is a key element in this project. TECO, its servicing dealer, and compression packager worked closely throughout the planning and installation stages of the project. To handle the amount of gas required, TECO selected the GEMINI F604-1 compressor, a four-throw, single-stage unit with a six-inch stroke manufactured by Weatherford Enterra Compression Co. (WECC) in Corpus Christi, TX. TECO also chose WECC to package the compressors. Responsibility for ongoing support of the units will be shared among TECO, the service dealer and the packager. TECO is sending people to be trained by WECC, and because the G3600 family of engines is still relatively new, both the Caterpillar dealer and WECC sent people for advanced training at Caterpillar facilities in Peoria, IL. As part of its service commitment to TECO, the servicing dealer drew up a detailed product support plan, encompassing these five concerns: Training, tooling; parts support; service support; and commissioning.

NONE

1996-10-01T23:59:59.000Z

299

Solar-Assisted Electric Vehicle Charging Station Interim Report  

SciTech Connect (OSTI)

Oak Ridge National Laboratory (ORNL) has been awarded $6.8 million in the Department of Energy (DOE) American Recovery and Reinvestment Act (ARRA) funds as part of an overall $114.8 million ECOtality grant with matching funds from regional partners to install 125 solar-assisted Electric Vehicle (EV) charging stations across Knoxville, Nashville, Chattanooga, and Memphis. Significant progress has been made toward completing the scope with the installation of 25 solar-assisted charging stations at ORNL; six stations at Electric Power Research Institute (EPRI); and 27 stations at Nissan's Smyrna and Franklin sites, with three more stations under construction at Nissan's new lithium-ion battery plant. Additionally, the procurement process for contracting the installation of 34 stations at Knoxville, the University of Tennessee Knoxville (UTK), and Nashville sites is underway with completion of installation scheduled for early 2012. Progress is also being made on finalizing sites and beginning installations of 30 stations in Nashville, Chattanooga, and Memphis by EPRI and Tennessee Valley Authority (TVA). The solar-assisted EV charging station project has made great strides in fiscal year 2011. A total of 58 solar-assisted EV parking spaces have been commissioned in East and Middle Tennessee, and progress on installing the remaining 67 spaces is well underway. The contract for the 34 stations planned for Knoxville, UTK, and Nashville should be underway in October with completion scheduled for the end of March 2012; the remaining three Nissan stations are under construction and scheduled to be complete in November; and the EPRI/TVA stations for Chattanooga, Vanderbilt, and Memphis are underway and should be complete by the end of March 2012. As additional Nissan LEAFs are being delivered, usage of the charging stations has increased substantially. The project is on course to complete all 125 solar-assisted EV charging stations in time to collect meaningful data by the end of government fiscal year 2012. Lessons learned from the sites completed thus far are being incorporated and are proving to be invaluable in completion of the remaining sites.

Lapsa, Melissa Voss [ORNL; Durfee, Norman [ORNL; Maxey, L Curt [ORNL; Overbey, Randall M [ORNL

2011-09-01T23:59:59.000Z

300

Donor doping of single-walled carbon nanotubes by filling of channels with silver  

SciTech Connect (OSTI)

The channels of single-walled carbon nanotubes (SWNTs) are filled with metallic silver. The synthesized nanocomposites are studied by Raman spectroscopy and optical absorption spectroscopy, and these data indicate a substantial modification of the electronic structure of the nanotubes upon their filling. Moreover, X-ray photoelectron spectroscopy shows that the incorporation of the metal leads to a change in the work function of SWNTs due to the Fermi level upshift and to the transfer of an electron density from inserted nanoparticles to the nanotube walls. Thus, the filling of the channels with silver results in donor doping of the nanotubes.

Kharlamova, M. V., E-mail: mv.kharlamova@gmail.com [Moscow State University (Russian Federation); Niu, J. J. [Drexel University, Department of Materials Science and Engineering (United States)

2012-09-15T23:59:59.000Z

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Method for filling the cavities of cells with a chromogenic fluid  

DOE Patents [OSTI]

A method and apparatus are disclosed for filling a cell cavity positioned between a first substrate and a second substrate with a cell filling liquid. The method entails forming at least one evacuation cavity encompassing at least a portion of an outer surface of each of the first and second substrates of a cell containing a cell cavity and isolating the cell cavity from the evacuation cavity; reducing a pressure in each of the evacuation cavity and the cell cavity; and dispensing the cell filling fluid into the cell cavity. The application is to the fabrication of electrochromic windows. 22 figs.

Tonazzi, J.C.L.; Kucharczyk, J.E. Jr.; Agrawal, A.

1999-01-05T23:59:59.000Z

302

Shell-Filling Effect in the Entanglement Entropies of Spinful Fermions  

E-Print Network [OSTI]

We consider the von Neumann and R\\'enyi entropies of the one dimensional quarter-filled Hubbard model. We observe that for periodic boundary conditions the entropies exhibit an unexpected dependence on system size: for L=4 mod 8 the results are in agreement with expectations based on conformal field theory, while for L=0 mod 8 additional contributions arise. We explain this observation in terms of a shell-filling effect, and develop a conformal field theory approach to calculate the extra term in the entropies. Similar shell filling effects in entanglement entropies are expected to be present in higher dimensions and for other multicomponent systems.

Fabian H. L. Essler; Andreas M. Läuchli; Pasquale Calabrese

2012-11-11T23:59:59.000Z

303

Waste Package Neutron Absorber, Thermal Shunt, and Fill Gas Selection Report  

SciTech Connect (OSTI)

Materials for neutron absorber, thermal shunt, and fill gas for use in the waste package were selected using a qualitative approach. For each component, selection criteria were identified; candidate materials were selected; and candidates were evaluated against these criteria. The neutron absorber materials evaluated were essentially boron-containing stainless steels. Two candidates were evaluated for the thermal shunt material. The fill gas candidates were common gases such as helium, argon, nitrogen, carbon dioxide, and dry air. Based on the performance of each candidate against the criteria, the following selections were made: Neutron absorber--Neutronit A978; Thermal shunt--Aluminum 6061 or 6063; and Fill gas--Helium.

V. Pasupathi

2000-01-28T23:59:59.000Z

304

Design of high pressure metering and regulating stations  

SciTech Connect (OSTI)

Metering and regulating stations effectively serve as the cash registers of the natural gas industry. While the potential for lost revenue resulting from improper design is a serious consideration, it is not the only one. The potential exists for problems such as excessive noise levels, inaccurate reflection of lost and unaccounted-for gas, and numerous potentially hazardous situations. The best time to limit the potential for problems is during the design process. This, together with the critical nature of these stations, dictates that proper design is imperative. Proper design of metering and regulating stations is a constantly changing and extremely complicated subject. There are virtually an infinite number of situations that the designer can encounter in evaluating his design. In view of this, it is impossible to develop a cookbook method of designing these stations that covers all possible situations. The emphasis of this paper is to briefly touch on the major aspects of metering and regulating station design. Steps involved in station design are: 1. Collection of data on the proposed station. 2. Determination of piping configuration. 3. Selection of measurement equipment. 4. Selection of pressure regulating and overpressure protection equipment. 5. Communication of the final design to field personnel.

Rehler, D.A. [Oklahoma Natural Gas Co., Enid, OK (United States)

1995-12-01T23:59:59.000Z

305

F.Gautier, J. Gilbert, J.-P. Dalmont, R. Pic Vila, Wave propagation in a fluid-filled cylindrical membrane WAVE PROPAGATION IN A FLUID FILLED RUBBER TUBE  

E-Print Network [OSTI]

F.Gautier, J. Gilbert, J.-P. Dalmont, R. Picó Vila, Wave propagation in a fluid-filled cylindrical membrane 1 WAVE PROPAGATION IN A FLUID FILLED RUBBER TUBE: THEORETICAL AND EXPERIMENTAL RESULTS title: Wave propagation in a fluid-filled cylindrical membrane Professional address of the corresponding

Paris-Sud XI, Université de

306

OPTIMIZING PERFORMANCE OF THE HESKETT STATION  

SciTech Connect (OSTI)

The overall conclusion from this work is that a switch from river sand bed material to limestone at the R.M. Heskett Station would provide substantial benefits to MDU. A switch to limestone would increase the fuel flexibility of the unit, allowing fuels higher in both sodium and sulfur to be burned. The limestone bed can tolerate a much higher buildup of sodium in the bed without agglomeration, allowing either the bed turnover rate to be reduced to half the current sand feed rate for a fuel with equivalent sodium or allow a higher sodium fuel to be burned with limestone feed rates equivalent to the current sand feed rate. Both stack and ambient SO{sub 2} emissions can be controlled. A small improvement in boiler efficiency should be achievable by operating at lower excess oxygen levels at low load. This reduction in oxygen will also lower NO{sub x} emissions, providing a margin of safety for meeting emission standards. No detrimental effects of using limestone at the Heskett Station were uncovered as a result of the test burn. Some specific conclusions from this work include the following: The bed material feed rate can be reduced from the current rate of 5.4% of the coal feed rate (57.4 tons of sand/day) to 2.5% of the coal feed rate (27 tons of limestone/day). This will result in an annual savings of approximately $200,000. (1) SO{sub 2} emissions at the recommended feed rate would be approximately 250 ppm (0.82 lb/MMBtu) using a similar lignite. Based on the cost of the limestones, SO{sub 2} allowances could be generated at a cost of $60/ton SO{sub 2} , leaving a large profit margin for the sale of allowances. The addition of limestone at the same rate currently used for sand feed could generate $455,000 net income if allowances are sold at $200/ton SO2 . (2) At full-load operation, unburned carbon losses increase significantly at excess oxygen levels below 2.8%. No efficiency gains are expected at high-load operation by switching from sand to limestone. By reducing the oxygen level at low load to 8.5%, an efficiency gain of approximately 1.2% could be realized, equating to $25,000 to $30,000 in annual savings. (3) A reduction of 25 tons/day total ash (bed material plus fly ash) will be realized by using limestone at the recommended feed rate compared to the current sand feed rate. No measurable change in volume would be realized because of the lower bulk density of the limestone-derived material.

Michael D. Mann; Ann K. Henderson

1999-03-01T23:59:59.000Z

307

Bridging the Gap Between Transportation and Stationary Power: Hydrogen Energy Stations and their Implications for the Transportation Sector  

E-Print Network [OSTI]

Economic Analysis of Hydrogen Energy Station Concepts,E 2 Four Potential Types of Hydrogen Energy Stations VehicleOperational Toronto Hydrogen Energy Station Stationary PEMFC

Weinert, Jonathan X.; Lipman, Timothy; Unnasch, Stephen

2005-01-01T23:59:59.000Z

308

OPTIMIZING GEO-CELLULAR RESERVOIR MODELING IN A BRAIDED RIVER INCISED VALLEY FILL: POSTLE FIELD, TEXAS COUNTY, OKLAHOMA  

E-Print Network [OSTI]

fill sandstones. EOR practices, in the form water flood and CO2 miscible flooding in the field have led

309

Toroidal Dehn fillings on hyperbolic 3-manifolds Cameron McA. Gordon  

E-Print Network [OSTI]

Toroidal Dehn fillings on hyperbolic 3-manifolds Cameron McA. Gordon Ying-Qing Wu Author address 0305846. Ying-Qing Wu was partially supported by NSF grant DMS 0203394. vi #12;1. INTRODUCTION 1 1

Wu, Ying-Qing

310

Submitted to SIGGRAPH 2001 Filling holes in complex surfaces using volumetric diffusion  

E-Print Network [OSTI]

plausible, visually pleasing geometry, · distinguish in the output model betSubmitted to SIGGRAPH 2001 Filling holes in complex surfaces using volumetric diffusion Steve Marschner James Davis Matt Garr Marc Levoy Stanford University Abstract We address the problem of building

Stanford University

311

Procedures for Filling Short Gaps in Energy Use and Weather Data  

E-Print Network [OSTI]

Filling short gaps (a few hours) in hourly energy use and weather data can be useful for (i) retrofit savings analysis and calculation, and for (ii) diagnostic purposes. The paper evaluates four methods for rehabilitating short periods of missing...

Chen, H.; Claridge, D. E.

2000-01-01T23:59:59.000Z

312

Micro-chamber filling experiments for validation of macro models with applications in capillary driven microfluidics  

E-Print Network [OSTI]

Prediction of bubble formation during filling of microchambers is often critical for determining the efficacy of microfluidic devices in various applications. In this study experimental validation is performed to verify the predictions from a...

Gauntt, Stephen Byron

2009-05-15T23:59:59.000Z

313

Case Study: Passive Solar Concepts Adapted to In-Fill Housing in a Hot, Humid Climate  

E-Print Network [OSTI]

In-fill housing for central city areas appears to be an answer to the continuing need for compact, affordable dwelling unite that will improve the neighborhood environment. There exist many central city areas in Louisiana where lots are unusually...

McQueen, T. M.; White, J. T.

1985-01-01T23:59:59.000Z

314

Integrated Gasification Combined Cycle (IGCC) demonstration project, Polk Power Station -- Unit No. 1. Annual report, October 1993--September 1994  

SciTech Connect (OSTI)

This describes the Tampa Electric Company`s Polk Power Station Unit 1 (PPS-1) Integrated Gasification Combined Cycle (IGCC) demonstration project which will use a Texaco pressurized, oxygen-blown, entrained-flow coal gasifier to convert approximately 2,300 tons per day of coal (dry basis) coupled with a combined cycle power block to produce a net 250 MW electrical power output. Coal is slurried in water, combined with 95% pure oxygen from an air separation unit, and sent to the gasifier to produce a high temperature, high pressure, medium-Btu syngas with a heat content of about 250 Btu/scf (LHV). The syngas then flows through a high temperature heat recovery unit which cools the syngas prior to its entering the cleanup systems. Molten coal ash flows from the bottom of the high temperature heat recovery unit into a water-filled quench chamber where it solidifies into a marketable slag by-product.

NONE

1995-05-01T23:59:59.000Z

315

Cooperative UAV-Based Communications Backbone for Sensor Networks  

SciTech Connect (OSTI)

The objective of this project is to investigate the use of unmanned air vehicles (UAVs) as mobile, adaptive communications backbones for ground-based sensor networks. In this type of network, the UAVs provide communication connectivity to sensors that cannot communicate with each other because of terrain, distance, or other geographical constraints. In these situations, UAVs provide a vertical communication path for the sensors, thereby mitigating geographic obstacles often imposed on networks. With the proper use of UAVs, connectivity to a widely disbursed sensor network in rugged terrain is readily achieved. Our investigation has focused on networks where multiple cooperating UAVs are used to form a network backbone. The advantage of using multiple UAVs to form the network backbone is parallelization of sensor connectivity. Many widely spaced or isolated sensors can be connected to the network at once using this approach. In these networks, the UAVs logically partition the sensor network into sub-networks (subnets), with one UAV assigned per subnet. Partitioning the network into subnets allows the UAVs to service sensors in parallel thereby decreasing the sensor-to-network connectivity. A UAV services sensors in its subnet by flying a route (path) through the subnet, uplinking data collected by the sensors, and forwarding the data to a ground station. An additional advantage of using multiple UAVs in the network is that they provide redundancy in the communications backbone, so that the failure of a single UAV does not necessarily imply the loss of the network.

Roberts, R S

2001-10-07T23:59:59.000Z

316

To learn more about AT&T Network Sourcing Solutions, visit www.att.com/network-sourcing or have us contact you.  

E-Print Network [OSTI]

Management owns and operates 17 waste-to-energy facilities, five independent power production plants and 115 1,200 recycling facilities, transfer stations, landfills and waste-to-energy plants, 22 call centers and implement a full-service solution. An AT&T Virtual Private Network increased network capacity

Fisher, Kathleen

317

SOARCA Peach Bottom Atomic Power Station Long-Term Station Blackout Uncertainty Analysis: Knowledge Advancement.  

SciTech Connect (OSTI)

This paper describes the knowledge advancements from the uncertainty analysis for the State-of- the-Art Reactor Consequence Analyses (SOARCA) unmitigated long-term station blackout accident scenario at the Peach Bottom Atomic Power Station. This work assessed key MELCOR and MELCOR Accident Consequence Code System, Version 2 (MACCS2) modeling uncertainties in an integrated fashion to quantify the relative importance of each uncertain input on potential accident progression, radiological releases, and off-site consequences. This quantitative uncertainty analysis provides measures of the effects on consequences, of each of the selected uncertain parameters both individually and in interaction with other parameters. The results measure the model response (e.g., variance in the output) to uncertainty in the selected input. Investigation into the important uncertain parameters in turn yields insights into important phenomena for accident progression and off-site consequences. This uncertainty analysis confirmed the known importance of some parameters, such as failure rate of the Safety Relief Valve in accident progression modeling and the dry deposition velocity in off-site consequence modeling. The analysis also revealed some new insights, such as dependent effect of cesium chemical form for different accident progressions. (auth)

Gauntt, Randall O.; Mattie, Patrick D.; Bixler, Nathan E.; Ross, Kyle; Cardoni, Jeffrey N; Kalinich, Donald A.; Osborn, Douglas M.; Sallaberry, Cedric Jean-Marie; Ghosh, S. Tina

2014-02-01T23:59:59.000Z

318

A Preliminary Evaluation of Using Fill Materials to Stabilize Used Nuclear Fuel During Storage and Transportation  

SciTech Connect (OSTI)

This report contains a preliminary evaluation of potential fill materials that could be used to fill void spaces in and around used nuclear fuel contained in dry storage canisters in order to stabilize the geometry and mechanical structure of the used nuclear fuel during extended storage and transportation after extended storage. Previous work is summarized, conceptual descriptions of how canisters might be filled were developed, and requirements for potential fill materials were developed. Elements of the requirements included criticality avoidance, heat transfer or thermodynamic properties, homogeneity and rheological properties, retrievability, material availability and cost, weight and radiation shielding, and operational considerations. Potential fill materials were grouped into 5 categories and their properties, advantages, disadvantages, and requirements for future testing were discussed. The categories were molten materials, which included molten metals and paraffin; particulates and beads; resins; foams; and grout. Based on this analysis, further development of fill materials to stabilize used nuclear fuel during storage and transportation is not recommended unless options such as showing that the fuel remains intact or canning of used nuclear fuel do not prove to be feasible.

Maheras, Steven J.; Best, Ralph; Ross, Steven B.; Lahti, Erik A.; Richmond, David J.

2012-08-01T23:59:59.000Z

319

Cranberry Station Celebrates 100th Anniversary with a 100 Year Endowment  

E-Print Network [OSTI]

Cranberry Station Celebrates 100th Anniversary with a 100 Year Endowment The Cranberry Station established with contributions from growers, friends, ag companies, and cranberry handlers. The funds

Massachusetts at Amherst, University of

320

Vision for Rollout of Fuel Cell Vehicles and Hydrogen Fuel Stations...  

Office of Environmental Management (EM)

Vision for Rollout of Fuel Cell Vehicles and Hydrogen Fuel Stations Vision for Rollout of Fuel Cell Vehicles and Hydrogen Fuel Stations This document establishes the California...

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Tri-Generation Success Story: World's First Tri-Gen EnergyStation...  

Energy Savers [EERE]

Energy Department, the Fountain Valley energy station is the world's first tri-generation hydrogen energy and electrical power station to provide transportation fuel to the public...

322

Survey Results and Analysis of the Cost and Efficiency of Various Operating Hydrogen Fueling Stations  

SciTech Connect (OSTI)

Existing Hydrogen Fueling Stations were surveyed to determine capital and operational costs. Recommendations for cost reduction in future stations and for research were developed.

Cornish, John

2011-03-05T23:59:59.000Z

323

Network Programming 1 Computer Networks  

E-Print Network [OSTI]

Network Programming 1 Computer Networks client/server architecture, protocols, and sockets 2;Network Programming 1 Computer Networks client/server architecture, protocols, and sockets 2 Network;client/server architecture Client/server architecture defines the communication between two computers

Verschelde, Jan

324

Predicting the performance of local seismic networks using Matlab and Google Earth.  

SciTech Connect (OSTI)

We have used Matlab and Google Earth to construct a prototype application for modeling the performance of local seismic networks for monitoring small, contained explosions. Published equations based on refraction experiments provide estimates of peak ground velocities as a function of event distance and charge weight. Matlab routines implement these relations to calculate the amplitudes across a network of stations from sources distributed over a geographic grid. The amplitudes are then compared to ambient noise levels at the stations, and scaled to determine the smallest yield that could be detected at each source location by a specified minimum number of stations. We use Google Earth as the primary user interface, both for positioning the stations of a hypothetical local network, and for displaying the resulting detection threshold contours.

Chael, Eric Paul

2009-11-01T23:59:59.000Z

325

Waiting for TOD : developing in the Millbrae BART Station Area  

E-Print Network [OSTI]

The suburban terminus station dedicates large amounts of land for parking in order to cater to its driving riders, and causes a trade-off tension between attracting ridership through providing park-and-rides and building ...

Shih, Janet Wei

2012-01-01T23:59:59.000Z

326

College Station Utilities- Residential Energy Back II Rebate Program  

Broader source: Energy.gov [DOE]

College Station Utilities offers an incentive for residential customers to install energy efficient HVAC equipment through the Energy Back II Program. To qualify for the rebate, the A/C system...

327

Strategy for international cooperation in planning the Chinese Space Station  

E-Print Network [OSTI]

After ten years of planning and pre-development, the Chinese government approved the space station project on September 25, 2010. In October 2010, the People's Republic of China (PRC) officially announced its independent ...

Foley, Jordan J. (Jordan James)

2014-01-01T23:59:59.000Z

328

Microsoft Word - Noxon Radio Station Upgrade CX.doc  

Broader source: Energy.gov (indexed) [DOE]

Action: Noxon Radio Station Upgrade Project Budget Information: Work Order 00254987 Task 03 Categorical Exclusion Applied (from Subpart D, 10 C.F.R. Part 1021: B1.7...

329

Where the Rubber Meets the Road -- the Alternative Fuel Station...  

Broader source: Energy.gov (indexed) [DOE]

Road -- the Alternative Fuel Station Locator August 10, 2010 - 2:32pm Addthis Dennis A. Smith Director, National Clean Cities Last week, this blog highlighted the highly efficient...

330

Niwot Ridge CRN Station Up & On-Line.  

E-Print Network [OSTI]

Niwot Ridge CRN Station Up & On-Line. I made a decision after the Science Panel Review to put tree removal Wind Speed 3, terrain elevation change Solar Radiation 3, solar shading to west #12;

331

Southwest Region Experiment Station - Final Technical Report  

SciTech Connect (OSTI)

Southwest Technology Development Institute (SWTDI), an independent, university-based research institute, has been the operator of the Southwest Region Photovoltaic Experiment Station (SWRES) for almost 30 years. The overarching mission of SWTDI is to position PV systems and solar technologies to become cost-effective, major sources of energy for the United States. Embedded in SWTDI's general mission has been the more-focused mission of the SWRES: to provide value added technical support to the DOE Solar Energy Technologies Program (SETP) to effectively and efficiently meet the R&D needs and targets specified in the SETP Multi-Year Technical Plan. : The DOE/SETP goals of growing U.S. PV manufacturing into giga-watt capacities and seeing tera-watt-hours of solar energy production in the U.S. require an infrastructure that is under development. The staff of the SWRES has supported DOE/SETP through a coherent, integrated program to address infrastructural needs inhibiting wide-scale PV deployment in three major technical categories: specialized engineering services, workforce development, and deployment facilitation. The SWRES contract underwent three major revisions during its five year period-of- performance, but all tasks and deliverables fell within the following task areas: Task 1: PV Systems Assistance Center 1. Develop a Comprehensive multi-year plan 2. Provide technical workforce development materials and workshops for PV stakeholder groups including university, professional installers, inspectors, state energy offices, Federal agencies 3. Serve on the NABCEP exam committee 4. Provide on-demand technical PV system design reviews for U.S. PV stakeholders 5. Provide PV system field testing and instrumentation, technical outreach (including extensive support for the DOE Market Transformation program) Task 2: Design-for-Manufacture PV Systems 1. Develop and install 18 kW parking carport (cost share) and PV-thermal carport (Albuquerque) deriving and publishing lessons learned Task 3: PV Codes and Standards 1. Serve as the national lead for development and preparation of all proposals (related to PV) to the National Electrical Code 2. Participate in the Standards Technical Panels for modules (UL1703) and inverters (UL1741) Task 4: Assess Inverter Long Term Reliability 1. Install and monitor identical inverters at SWRES and SERES 2. Operate and monitor all inverters for 5 years, characterizing all failures and performance trends Task 5: Test and Evaluation Support for Solar America Initiative 1. Provide test and evaluation services to the National Laboratories for stage gate and progress measurements of SAI TPP winners

Rosenthal, A

2011-08-19T23:59:59.000Z

332

Large Optic Drying Station: Summary of Dryer Certification Tests  

SciTech Connect (OSTI)

The purpose of this document is to outline the methodology used to baseline and maintain the cleanliness status of the newly built and installed Large Optic Cleaning Station (LOCS). The station has currently been in use for eleven months; and after many cleaning studies and implementation of resulting improvements appears to be cleaning optics to a level that is acceptable for the fabrication of Nano-Laminates.

Barbee, T W; Ayers, S L; Ayers, M J

2009-08-28T23:59:59.000Z

333

Energy consumption in cellular network: ON-OFF model and impact of mobility  

E-Print Network [OSTI]

Energy consumption in cellular network: ON-OFF model and impact of mobility Thanh Tung Vu Telecom consumption in cellular network and we focus on the distribution of energy consumed by a base station. We first define the energy consumption model, in which the consumed energy is divided into two parts

334

Sismos l'Ecole: A Worldwide Network of Real-Time Seismometers in Schools  

E-Print Network [OSTI]

Sismos à l'Ecole: A Worldwide Network of Real-Time Seismometers in Schools by F. Courboulex, J. L countries in the world. Thanks to Sismos à l'Ecole (SaE) network stations, acces- sible in real time

Nolet, Guust

335

Instructions for filling liquid Helium for the 800 MHz magnet This is a twoperson job and will require 2 x 100 liter tanks of liquid helium if filling  

E-Print Network [OSTI]

and will require 2 x 100 liter tanks of liquid helium if filling from 207 mm (41%). · Move the ladder to the side and place the helium tank to the right of the leg facing the 500 system and as close to the magnet as possible. · Cut all ties from the helium tanks · Hand tighten the homemade fitting to the vent port

Oliver, Douglas L.

336

An Overview of Energy-efficient Base Station Management Techniques  

E-Print Network [OSTI]

expenditures (CAPEX). However, most of the time, networks work at low to medium load. This is especially true

Wichmann, Felix

337

ARM: Broadband Radiometer Station (BRS) broadband shortwave and longwave 1-min radiation data with Dutton correction  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

Broadband Radiometer Station (BRS) broadband shortwave and longwave 1-min radiation data with Dutton correction

Stoffel, Tom; Kay, Bev; Habte, Aron; Anderberg, Mary; Kutchenreiter, Mark

338

INVESTIGATION OF HYDRAULIC PROBLEMS IN PUMPING STATION; CASE STUDY  

E-Print Network [OSTI]

Pumping stations play an important role in agriculture development projects. Performance of the pumping stations should satisfy water requirements, and management. There are many problems face these pumping stations affecting their reliability and stability. Hydraulic problems are the most important item in the field of pumping station operation and design. Motivation of this research was presence of wear and pitting impellers and casing of double suction volute casing centrifugal pumps for Ahmed Orabee Pumping Station. Vibration level, hydraulic performance test and visual inspection of impeller wear and pitting show that cavitation problem is the cause of damage. Cavitation normally occurs when liquid at a constant temperature is subjected to vapor pressure either by static or dynamic means. If the local pressure somewhere in the fluid drops to or below vapor pressure and nuclei are present, vapor cavities can be formed. As long as the local pressure stays at vapor pressure and cavity has reached a critical diameter, it will continue to grow rapidly. If the surrounding pressure is above vapor pressure, the bubbles become unstable and collapse. The

M. A. Younes

339

Effect of temperature on performance of {sup 3}He filled neutron proportional counters  

SciTech Connect (OSTI)

Neutron detectors used for cosmic neutron monitoring and various other applications are mounted in hostile environment. It is essential for detectors to sustain extreme climatic conditions, such as extreme temperature and humidity. Effort is made to evaluate the performance of detectors in extreme temperature in terms of pulse height distribution and avalanche formation. Neutron detectors filled with {sup 3}He incorporate an additive gas with quantity optimized for a particular application. Measurements are performed on neutron detectors filled with {sup 3}He and stopping gases Kr and CF{sub 4}. Detector performance for these fill gas combinations in terms of pulse height distribution is evaluated. Gas gain and Diethorn gas constants measured and analyzed for the microscopic effect on pulse formation. Results from these investigations are presented.

Desai, Shraddha S., E-mail: ssdesai@barc.gov.in [Solid State Physics Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

2014-04-24T23:59:59.000Z

340

Capillary filling with giant liquid/solid slip: dynamics of water uptake by carbon nanotubes  

E-Print Network [OSTI]

This article discusses the way the standard description of capillary filling dynamics has to be modified to account for liquid/solid slip in nanometric pores. It focuses in particular on the case of a large slip length compared to the pore size. It is shown that the liquid viscosity does not play a role, and that the flow is only controlled by the friction coefficient of the liquid at the wall. Moreover in the Washburn regime, the filling velocity does not depend on the tube radius. Finally, molecular dynamics simulations suggest that this standard description fails to describe the early stage of capillary filling of carbon nanotubes by water, since viscous dissipation at the tube entrance must be taken into account.

Laurent Joly

2011-12-06T23:59:59.000Z

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Modeling of the quantum dot filling and the dark current of quantum dot infrared photodetectors  

SciTech Connect (OSTI)

A generalized drift-diffusion model for the calculation of both the quantum dot filling profile and the dark current of quantum dot infrared photodetectors is proposed. The confined electrons inside the quantum dots produce a space-charge potential barrier between the two contacts, which controls the quantum dot filling and limits the dark current in the device. The results of the model reasonably agree with a published experimental work. It is found that increasing either the doping level or the temperature results in an exponential increase of the dark current. The quantum dot filling turns out to be nonuniform, with a dot near the contacts containing more electrons than one in the middle of the device where the dot occupation approximately equals the number of doping atoms per dot, which means that quantum dots away from contacts will be nearly unoccupied if the active region is undoped.

Ameen, Tarek A.; El-Batawy, Yasser M.; Abouelsaood, A. A. [Department of Engineering Mathematics and Physics, Faculty of Engineering, Cairo University, Giza (Egypt)

2014-02-14T23:59:59.000Z

342

Occurrence of pore-filling halite in carbonate rocks, Nesson Anticline, Williston basin, North Dakota  

SciTech Connect (OSTI)

Clear, colorless pore-filling halite of late diagenetic origin occurs locally in the Devonian Dawson Bay, Winnipegosis, and Ashern Formations, the Silurian Interlake Formation, and the Ordovician Red River Formation. The halite occludes a variety of pore types and individual pores are filled with single crystals or aggregates of only a few crystals. This halite is present in quantities ranging from a trace to approximately 12%. Cores from McGregor field, Williams County, show the Winnipegosis Formation consists of mixed-skeletal lime wackestones and mudstones. These contain vugs up to 4 in. (10 cm) in size, intraparticle pores, and shelter porosity within pelecypod shells, up to 4 in. (10 cm) in size, which are occluded with halite. Halite also fills common small discontinuous vertical fractures. The upper 200 ft (61 m) of the Interlake Formation locally exhibits the most striking occurrences of pore-filling halite. These dolostones consist predominantly of intraclast-peloid mudstones, wackestones, packstones, occasional grainstones, algal boundstones, and solution-collapse breccias containing vug, fenestral, interparticle, shelter, intercrystalline, moldic, channel, breccia, and fracture porosity types. All porosity types, except intercrystalline, can be halite filled. A rare occurrence of pore-filling halite exists in Red River cores from Blue Buttes field, McKenzie County, where a dolomitic, mixed-skeletal, lime mudstone and wackestone lithofacies contains vugs, discontinuous vertical fractures, and intraparticle porosity types occluded with halite. In most occurrences, the pore systems were noneffective prior to halite infilling and had no potential as hydrocarbon reservoirs. However, it has been demonstrated that halite plugging in the Interlake Formation has locally formed updip seals to hydrocarbon migration.

Bucher, E.J.

1988-07-01T23:59:59.000Z

343

Stratigraphic architecture of the Tonganoxie Paleovalley Fill (Lower Virgilian) in Northeastern Kansas  

SciTech Connect (OSTI)

Lower Pennsylvanian paleovalley-confined sandstones are important petroleum reservoirs in the Midwest. In Kansas, such reservoirs have produced approximately 220 million bbl of oil and 1.7 tcf of gas. Valley-fill successions tend to become muddy upward, but there can be considerable local heterogeneity in which reservoir sandstones pass laterally into muddy sandstones or nonreservoir shales. The lack of understanding of this reservoir heterogeneity can lead to low drilling success rates. The Tonganoxie paleovalley (Upper Pennsylvanian, northeastern Kansas) contains facies very similar to Lower Pennsylvanian (Morrowan) valley fills, and can provide an outcrop- and subsurface-based model of sandstone deposition. The Tonganoxie paleovalley was incised during lowered sea level and filled during the subsequent transgression. Sandstones occur in four distinct architectural elements that were deposited during different phases of transgression. Type I sandstone consists of a belt of sandstone and conglomerate 3-18 m thick and confined to the trunk valley and wider portions of tributary valleys. Type I sandstone consists of amalgamated channel fills, has little or no mud, and has the highest porosity and permeability. The type I sandstone is overlain by estuarine deposits of sandstone (type II sandstones), rippled argillaceous sandstone to sandy mudstone, and coal. Most of the paleovalley was filled during this stage. The type II sandstones are narrow (1.5 km wide) arcuate bodies up to 8 km long and were likely deposited in tidal point bars near the fluvial to tidal transition, are either isolated sandstone bodies or are incised into type I sandstone. Type III sandstone bodies occur at the upstream limits of narrow tributaries and are probably bay-head deltas. Well logs indicate a range of mud content. Type IV sandstone is a thin (3 m) discontinuous sheet of marine sandstone deposited after most of the paleovalley had been filled.

Feldman, H.R. [Kansas Geological Survey, Lawrence, KS (United States); Gibling, M.R.; Wightman, W.G. [Dalhousie Univ., Nova Scotia (Canada)] [and others

1995-07-01T23:59:59.000Z

344

Optical properties of MFe{sub 4}P{sub 12} filled skutterudites  

SciTech Connect (OSTI)

Infrared reflectance spectroscopy measurements were made on four members of the MFe{sub 4}P{sub 12} family of filled skutterudites, with M=La, Th, Ce, and U. In progressing from M=La to U the system undergoes a metal-insulator transition. It is shown that, although the filling atom induces such dramatic changes in the transport properties of the system, it has only a small effect on lattice dynamics. We discuss this property of the compounds in the context of their possible thermoelectric applications. {copyright} {ital 1999} {ital The American Physical Society}

Dordevic, S.V.; Dilley, N.R.; Bauer, E.D.; Basov, D.N.; Maple, M.B. [Department of Physics, University of California, San Diego, La Jolla, California 92093-0319 (United States)] [Department of Physics, University of California, San Diego, La Jolla, California 92093-0319 (United States); Degiorgi, L. [Solid State Physics Laboratory HPF-F3/F18, ETH Zuerich, CH-8093 Zuerich (Switzerland)] [Solid State Physics Laboratory HPF-F3/F18, ETH Zuerich, CH-8093 Zuerich (Switzerland)

1999-10-01T23:59:59.000Z

345

Locating PHEV Exchange Stations in V2G  

E-Print Network [OSTI]

Plug-in hybrid electric vehicles (PHEVs) are an environmentally friendly technology that is expected to rapidly penetrate the transportation system. Renewable energy sources such as wind and solar have received considerable attention as clean power options for future generation expansion. However, these sources are intermittent and increase the uncertainty in the ability to generate power. The deployment of PHEVs in a vehicle-to-grid (V2G) system provide a potential mechanism for reducing the variability of renewable energy sources. For example, PHEV supporting infrastructures like battery exchange stations that provide battery service to PHEV customers could be used as storage devices to stabilize the grid when renewable energy production is fluctuating. In this paper, we study how to best site these stations in terms of how they can support both the transportation system and the power grid. To model this problem we develop a two-stage stochastic program to optimally locate the stations prior to the realizat...

Pan, Feng; Berscheid, Alan; Izraelevitz, David

2010-01-01T23:59:59.000Z

346

Cranberry Station Farm and Grounds Manager (R35360) The University of Massachusetts Cranberry Station (www.umass.edu/cranberry) has a  

E-Print Network [OSTI]

Cranberry Station Farm and Grounds Manager (R35360) The University of Massachusetts Cranberry Station (www.umass.edu/cranberry) has a full time/fully benefited position available. Benefits include vacation, retirement, medical, and dental. Duties: Under the general supervision of the Cranberry Station

Mountziaris, T. J.

347

A Differential Phase Shift Scheme for Quantum Key Distribution in Passive Optical Networks  

E-Print Network [OSTI]

We propose a scheme for quantum key distribution (QKD) in a passive optical network (PON) based on differential phase shift (DPS) coding. A centralized station including all expensive components serves many users, making it suitable for a true multi-user network in a local environment with moderate distances on the order of a few kilometers. The emphasis lies on an asymmetric design for cost effective implementation of network end points.

Michael Hentschel; Andreas Poppe; Bernhard Schrenk; Momtchil Peev; Edwin Querasser; Roland Lieger

2014-12-19T23:59:59.000Z

348

Solar photovoltaic power system for a radio station  

SciTech Connect (OSTI)

Under sponsorship of the US Department of Energy, Massachusetts Institute of Technology Lincoln Laboratory has developed a concept for a small photovoltaic power system. Of simple construction, the system uses low-cost, prefabricated, transportable units for easy, fast installation and requires minimal site preparation. The first application of this experimental system began operation in August 1979 at daytime AM radio station WNBO in Bryan, Ohio. The project was jointly undertaken by the Laboratory and the radio station. The photovoltaic system described holds promise for a wide range of applications and economic feasibility by the mid- to late-1980s.

Nichols, B. E.

1980-12-01T23:59:59.000Z

349

Design of photovoltaic central power station concentrator array  

SciTech Connect (OSTI)

A design for a photovoltaic central power station using tracking concentrators has been developed. The 100 MW plant is assumed to be located adjacent to the Saguaro Power Station of Arizona Public Service. The design assumes an advanced Martin Marietta two-axis tracking fresnel lens concentrator. The concentrators are arrayed in 5 MW subfields, each with its own power conditioning unit. The photovoltaic plant output is connected to the existing 115 kV switchyard. The site specific design allows detailed cost estimates for engineering, site preparation, and installation. Collector and power conditioning costs have been treated parametrically.

Not Available

1984-02-01T23:59:59.000Z

350

EIS-0210: Tampa Electric Company-Polk Power Station (Adopted)  

Broader source: Energy.gov [DOE]

The U.S. Environmental Protection Agency prepared this statement to fulfill its National Environmental Policy Act requirements with respect to the potential issuance of a permit to the Tampa Electric Company under the National Pollutant Discharge Elimination System for the 1,150-MW Polk Power Station, a new pollutant source. The U.S. Department of Energy served as a cooperating agency in the development of this document due to its potential role to provide cost-shared financial assistance for a 260-MW Integrated Gasification Combined Cycle unit at the Power Station under its Clean Coal Technology Demonstration Project, and adopted the document by August 1994.

351

Sandia National Laboratories: Hydrogen Refueling Stations Analysis Model  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassive SolarEducationStation Technology Infrastructure ResearchRefueling Stations

352

Construction of Anatomically Correct Models of Mouse Brain Networks 1  

E-Print Network [OSTI]

Construction of Anatomically Correct Models of Mouse Brain Networks 1 B. H. McCormick a, W. Koh a Y and Public Health, Texas A&M University, 4458 TAMU, College Station, TX 77843-4458 Abstract The Mouse Brain Web, a federated database, provides for the construction of anatomically correct models of mouse brain

Keyser, John

353

MOBILE FLEXIBLE NETWORKS: THE CHALLENGES AHEAD Merouane Debbah  

E-Print Network [OSTI]

with the right amount of regulation...just enough to let the agents in the network exploit fully the degrees their speed depending on the weather conditions for security reasons. Finally, in the case of electrical cars with the number of cooperating base stations. Hence, in theory, the only limi

Boyer, Edmond

354

An EAP ID-Based Authentication Method for Wireless Networks  

E-Print Network [OSTI]

(Certification Author- ity) and the burdensome management of certificates is removed. The presented) into IEEE 802 wired networks. It gave also birth to the IEEE 802.11i [2] which is more specific to wireless between two stations or a signature mechanism that lies on certificates to prove the ownership of a public

Paris-Sud XI, Université de

355

High Throughput Spectrum-aware Routing for Cognitive Radio Networks  

E-Print Network [OSTI]

High Throughput Spectrum-aware Routing for Cognitive Radio Networks Ashwin Sampath, Lei Yang, Lili, wireless nodes equipped with cognitive radios [11] do not operate on statically as- signed spectrum who own the spectrum, e.g. analog TV broadcast stations. Such flexibility means cognitive radios can

Zhao, Ben Y.

356

Proactive Design of n-Type (In, Ce) Filled Skutterudites Enabling High-Temperature Waste Heat Recovery  

Broader source: Energy.gov [DOE]

Thermoelectric and structural properties of n-type (In, Ce) filled skutterudites including power factors and ZT as a function of temperature are presented

357

Pressure calibrations for cell filling Harvard-Smithsonian Center for Astrophysics, Cambridge, MA 02138  

E-Print Network [OSTI]

, Cambridge, MA 02138 (1/20/00) Purpose: To describe procedures useful in filling various gas sample cells to 77 K, and thus eas- ily condense xenon into the cell. Practically, this means that all the gas the gases in the cell are valid only for a binary gas mixture where one of the gases can be condensed (i

Walsworth, Ronald L.

358

A Study of the Filling of Wall Cavities With Retrofit Wall Insulation.  

SciTech Connect (OSTI)

The Pacific Northwest Power Marketing Agency, the Bonneville Power Administration (BPA), conducted a retrofit wall insulation study to determine the effects of various obstructions within a wall cavity, where voids are likely to occur, and preferred filling methods and material types. The insulation test structure was composed of four 8-foot /times/ 12-foot walls, and was built using standard construction practices. The inside walls were clear plastic glazing, instead of gypsum board, to enable viewing of the filling process. A total of eight tests were performed: four cellulose, two rockwool, and two fiberglass. One- and two-hole filling methods were observed. All insulations were found to perform in the same basic manner with all experiencing the same problem areas. Common installer problems were empty spaces at the tops of cavities and missed cavities, especially above headers. Wiring and lath and plaster consistently caused reduced insulation densities in cavities. The problems with wiring, lath and plaster, and other features in the wall cavities were avoided with the use of a filler tube. The filler tube also provided a more consistent fill along the length of the entire cavity. 2 figs., 3 tabs.

Flores, Joseph A.; Grill, Alan R.

1988-08-01T23:59:59.000Z

359

Quantitative study of mixing in annular and raschig ring filled tanks  

SciTech Connect (OSTI)

A quantitative study of mixing, which utilized the exit age distribution theory, has been completed for bench-scale annular and raschig ring filled tanks, in addition to a pilot-scale annular tank. A study of mixing and fluid flow in a full-scale, single-entry, raschig ring filled tank also was initiated. Results showed the bench-scale raschig ring filled tank approached plug-flow (no mixing) behavior. In a bench-scale annular tank, regardless of whether fluid entered tangentially or nontangentially, the vessel approached continuously stirred tank reactor behavior (perfect mixing). The pilot-scale annular tank approached continuously stirred tank reactor behavior only when tangential entry was used. Mixing in the full-scale raschig ring filled tank he tank did not approach eithr the perfect or the no mixing situations. Instead, the tank had a flow pattern in which solution channeled through a small volume of the tank, leaving the regions outside the channel effectively inactive.

Fredrickson, M. A.

1980-07-14T23:59:59.000Z

360

STATISTICS OF MIXING DISTRIBUTIONS IN FILLED ELASTOMERS PROCESSED BY TWIN SCREW EXTRUSION  

E-Print Network [OSTI]

screw extruder under controlled extruder geometry, order of ingredient addition and die pressurizationC. This formulation was twin screw extruded using an annular die with a star-shaped mandrel (see Fig.1). Three controlSTATISTICS OF MIXING DISTRIBUTIONS IN FILLED ELASTOMERS PROCESSED BY TWIN SCREW EXTRUSION Elvan

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

PRELIMINARY DESIGN PROCEDURE FOR EPS-BLOCK GEOFOAM LIGHTWEIGHT FILL IN LEVEES OVERLYING  

E-Print Network [OSTI]

PRELIMINARY DESIGN PROCEDURE FOR EPS-BLOCK GEOFOAM LIGHTWEIGHT FILL IN LEVEES OVERLYING SOFT GROUND Final Paper Submitted July 28, 2010 #12;1 PRELIMINARY DESIGN PROCEDURE FOR EPS-BLOCK GEOFOAM LIGHTWEIGHT the load applied to the soft foundation soils. The use of expanded-polystyrene (EPS)-block geofoam

Horvath, John S.

362

MSU biofuels research fills need for new sources July 28, 2006 --By Carol Flaherty  

E-Print Network [OSTI]

MSU biofuels research fills need for new sources July 28, 2006 -- By Carol Flaherty The words are becoming familiar, even if the products aren't: biofuel, biobased, biodiesel, bioethanol. All refer to fuel collaborators are investigating Montana's potential for producing biofuels using "biomass," which refers to all

Maxwell, Bruce D.

363

Fluid transients and fluid-structure interaction in flexible liquid-filled piping  

E-Print Network [OSTI]

Fluid transients and fluid-structure interaction in flexible liquid-filled piping David C Wiggert in piping systems FSI consists of the transfer of momentum and forces between piping and the contained or may be initiated by mechanical ac- tion of the piping. The interaction is manifested in pipe vibration

Tijsseling, A.S.

364

Mathematical Model of an Air-Filled Alpha Stirling Refrigerator Patrick McFarlane,1, a)  

E-Print Network [OSTI]

into a useful temperature difference. Though there are a few current applications of Stirling engines in energy of the work done on Stirling cycle-based machines. Although the re- view focused on engines, the analysisMathematical Model of an Air-Filled Alpha Stirling Refrigerator Patrick McFarlane,1, a) Fabio

Sen, Mihir

365

Filling holes in regional carbon budgets: Predicting peat depth in a north temperate lake district  

E-Print Network [OSTI]

Filling holes in regional carbon budgets: Predicting peat depth in a north temperate lake district] Peat deposits contain on the order of 1/6 of the Earth's terrestrial fixed carbon (C), but uncertainty in peat depth precludes precise estimates of peat C storage. To assess peat C in the Northern Highlands

Turner, Monica G.

366

Microfluidic Assembly of Homogeneous and Janus Colloid-Filled Hydrogel Granules  

E-Print Network [OSTI]

Microfluidic Assembly of Homogeneous and Janus Colloid-Filled Hydrogel Granules Robert F. Shepherd 23234 ReceiVed March 21, 2006. In Final Form: August 15, 2006 The microfluidic assembly of colloid.11 A new route to granulation is suggested by the emergence of microfluidic techniques that allow

Lewis, Jennifer

367

Numerical modeling and experimental validation of uniform microchamber filling in centrifugal microfluidics  

E-Print Network [OSTI]

microfluidics Jonathan Siegrist,*a Mary Amasia,a Navdeep Singh,b Debjyoti Banerjeeb and Marc Madoua Received 1st analysis of microchamber filling in centrifugal microfluidics is presented. In the development of micro on centrifugal microfluidic platforms, numerical modeling using the Volume of Fluids method is performed

Banerjee, Debjyoti

368

Free carrier induced spectral shift for GaAs filled metallic hole arrays  

E-Print Network [OSTI]

. Soref, and J. A. D. Alamo, "Carrier-induced change in refractive index of InP, GaAs, and InGaAsP," IEEE-photon absorption (3PA) assisted by strongly enhanced local fields, reduce the refractive index of GaAs in ~200-nm thick active area through band filling and free carrier absorption. Therefore, the surface plasma wave

New Mexico, University of

369

Improved Load Distribution for Load Rating of Low-Fill Box Structures  

E-Print Network [OSTI]

. The distribution of live loads on the top slab of a box culvert plays a major role in determining the rating factor of the culvert. The current AASHTO guidelines do not consider the effects of pavements present above the fill while determining the load distribution...

Acharya, Raju

2012-12-31T23:59:59.000Z

370

Multiple-Filled Skutterudites: High Thermoelectric Figure of Merit through Separately Optimizing Electrical and Thermal Transports  

SciTech Connect (OSTI)

Skutterudites CoSb{sub 3} with multiple cofillers Ba, La, and Yb were synthesized and very high thermoelectric figure of merit ZT = 1.7 at 850 K was realized. X-ray diffraction of the densified multiple-filled bulk samples reveals all samples are phase pure. High-resolution scanning transmission electron microscopy (STEM) and energy dispersive X-ray spectroscopy (EDS) analysis confirm that multiple guest fillers occupy the nanoscale-cages in the skutterudites. The fillers are further shown to be uniformly distributed and the Co-Sb skutterudite framework is virtually unperturbed from atomic scale to a few micrometers. Our results firmly show that high power factors can be realized by adjusting the total filling fraction of fillers with different charge states to reach the optimum carrier density, at the same time, lattice thermal conductivity can also be significantly reduced, to values near the glass limit of these materials, through combining filler species of different rattling frequencies to achieve broad-frequency phonon scattering. Therefore, partially filled skutterudites with multiple fillers of different chemical nature render unique structural characteristics for optimizing electrical and thermal transports in a relatively independent way, leading to continually enhanced ZT values from single- to double-, and finally to multiple-filled skutterudites. The idea of combining multiple fillers with different charge states and rattling frequencies for performance optimization is also expected to be valid for other caged TE compounds.

Zhang, Weiqing [Chinese Academy of Sciences; Yang, Jiong [Chinese Academy of Sciences; Yang, Jihui [General Motors Corporation; Wang, Hsin [ORNL; Salvador, James R. [GM R& D and Planning, Warren, Michigan; Shi, Xun [General Motors Corporation-R& D; Chi, Miaofang [ORNL; Cho, Jung Y [GM R& D and Planning, Warren, Michigan; Bai, Shengqiang [Chinese Academy of Sciences; Chen, Lidong [Chinese Academy of Sciences

2011-01-01T23:59:59.000Z

371

A NEW MULTIDIRECTIONAL EXTRAPOLATION HOLE-FILLING METHOD FOR DEPTH-IMAGE-BASED RENDERING  

E-Print Network [OSTI]

A NEW MULTIDIRECTIONAL EXTRAPOLATION HOLE-FILLING METHOD FOR DEPTH-IMAGE-BASED RENDERING Lai-Man Po School of Peking University, Shenzhen, China ABSTRACT Depth-Image-Based Rendering (DIBR) is widely used synthesis with high-quality depth map. Index Terms - Depth-Image-Based-Rendering, DIBR, Hole

Po, Lai-Man

372

Modeling of quasistatic and dynamic load responses of filled viscoelastic materials  

E-Print Network [OSTI]

are typically used for static finite element analysis (see [9]). The CRSC/Lord team worked, both theoreticallyModeling of quasi­static and dynamic load responses of filled viscoelastic materials H.T. Banks factors to the complications arising in the process of formulating models. Damping is highly complex

373

POLYPROPYLENE COMPOSITES FILLED WITH STEAM-EXPLODED WOOD FIBERS FROM BEETLE-KILLED LOBLOLLY PINE  

E-Print Network [OSTI]

POLYPROPYLENE COMPOSITES FILLED WITH STEAM-EXPLODED WOOD FIBERS FROM BEETLE-KILLED LOBLOLLY PINE of Tennessee Knoxville, TN 37996 (Received October 2005) ABSTRACT Beetle-killed loblolly pine chips were steam. Keywords: Beetle-killed pine, steam explosion, polypropylene composite, compatibilizer, flexural prop

Wang, Siqun

374

Apparatus and methods for determining gas saturation and porosity of a formation penetrated by a gas filled or liquid filled borehole  

DOE Patents [OSTI]

Methods and apparatus are disclosed for determining gas saturation, liquid saturation, porosity and density of earth formations penetrated by a well borehole. Determinations are made from measures of fast neutron and inelastic scatter gamma radiation induced by a pulsed, fast neutron source. The system preferably uses two detectors axially spaced from the neutron source. One detector is preferably a scintillation detector responsive to gamma radiation, and a second detector is preferably an organic scintillator responsive to both neutron and gamma radiation. The system can be operated in cased boreholes which are filled with either gas or liquid. Techniques for correcting all measurements for borehole conditions are disclosed.

Wilson, Robert D. (477 W. Scenic Dr., Grand Junction, CO 81503)

2001-03-27T23:59:59.000Z

375

Impact of Gastric Filling on Radiation Dose Delivered to Gastroesophageal Junction Tumors  

SciTech Connect (OSTI)

Purpose: This study examined the impact of gastric filling variation on target coverage of gastroesophageal junction (GEJ) tumors in three-dimensional conformal radiation therapy (3DCRT), intensity-modulated radiation therapy (IMRT), or IMRT with simultaneous integrated boost (IMRT-SIB) plans. Materials and Methods: Eight patients previously receiving radiation therapy for esophageal cancer had computed tomography (CT) datasets acquired with full stomach (FS) and empty stomach (ES). We generated treatment plans for 3DCRT, IMRT, or IMRT-SIB for each patient on the ES-CT and on the FS-CT datasets. The 3DCRT and IMRT plans were planned to 50.4 Gy to the clinical target volume (CTV), and the same for IMRT-SIB plus 63.0 Gy to the gross tumor volume (GTV). Target coverage was evaluated using dose-volume histogram data for patient treatments simulated with ES-CT sets, assuming treatment on an FS for the entire course, and vice versa. Results: FS volumes were a mean of 3.3 (range, 1.7-7.5) times greater than ES volumes. The volume of the GTV receiving >=50.4 Gy (V{sub 50.4Gy}) was 100% in all situations. The planning GTV V{sub 63Gy} became suboptimal when gastric filling varied, regardless of whether simulation was done on the ES-CT or the FS-CT set. Conclusions: Stomach filling has a negligible impact on prescribed dose delivered to the GEJ GTV, using either 3DCRT or IMRT planning. Thus, local relapses are not likely to be related to variations in gastric filling. Dose escalation for GEJ tumors with IMRT-SIB may require gastric filling monitoring.

Bouchard, Myriam, E-mail: mybouchard@gmail.co [Department of Radiation Physics, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); McAleer, Mary Frances [Department of Radiation Oncology, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States); Starkschall, George, E-mail: gstarksc@mdanderson.or [Department of Radiation Physics, University of Texas M. D. Anderson Cancer Center, Houston, TX (United States)

2010-05-01T23:59:59.000Z

376

APPARENT WATER OPTICAL PROPERTIES AT THE CARIBBEAN TIME SERIES STATION  

E-Print Network [OSTI]

APPARENT WATER OPTICAL PROPERTIES AT THE CARIBBEAN TIME SERIES STATION Roy A. Armstrong, Jose M of Puerto Rico Mayagüez, Puerto Rico 00681 ABSTRACT The Caribbean Time Series, located 28 nautical miles in near- surface waters of the northeastern Caribbean Basin. Apparent optical properties such as, remote

Gilbes, Fernando

377

MET Stations and Web Cams in the Great Lakes  

E-Print Network [OSTI]

in Alpena, MI, Muskegon, MI, South Haven, MI, Michigan City, IN, Chicago, IL, and Toldeo, OH also include: Alpena, MI Chicago, IL Muskegon, MI Michigan City, IN South Haven, MI Toledo, OH Met Data Stations: Alpena, MI Chicago, IL Michigan City, IN Milwaukee, WI Muskegon, MI South Haven, MI Thunder Bay

378

National Aeronautics and Space Administration International Space Station  

E-Print Network [OSTI]

and technological endeavor ever undertaken, involving support from five space agencies representing 16 nations. Once's solar panels exceed the wingspan of a Boeing 777 jetliner and harness enough energy from the sunNational Aeronautics and Space Administration NASAfacts International Space Station Clearly

379

Great Lakes Hydrometeorological Station Directory Database and Internet Web Development  

E-Print Network [OSTI]

Great Lakes Hydrometeorological Station Directory Database and Internet Web Development Primary Investigator: Thomas Croley - NOAA GLERL (Emeritus) This project was completed in 2001 Overview A new directory in hydrometeorological data availability with in the Great Lakes. The new directory will consist of an updated database

380

DEVELOPMENT OF A TURNKEY COMMERCIAL HYDROGEN FUELING STATION  

E-Print Network [OSTI]

of the hydrogen fuel economy for buses, fleet vehicles, and ultimately personal vehicles. In order to demonstrate to the reforming of natural gas to produce a reformate stream; · Develop an efficient, cost-effective means the basis for future commercial Fueling Stations. 1 Proceedings of the 2002 U.S. DOE Hydrogen Program Review

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

VISITOR PARKING Pay station parking meters are available around  

E-Print Network [OSTI]

temporary parking needs. Daily scratch-off permits are available in advance from Parking Services. LOT METER PAY STATION RATES (SUMMER RATES MAY BE DISCOUNTED) HOW DO I GET A PERMIT? When parking on campus, a CSM parking permit is required Monday through Friday, from 7AM until 5 PM. Permits authorize parking

382

Bryan Balkenbush Fukushima Daiichi Nuclear Power Station `Issue'  

E-Print Network [OSTI]

Bryan Balkenbush Fukushima Daiichi Nuclear Power Station `Issue' Map: Timeline: March 11th, sparking a tsunami March 14th : Explosion reported by second nuclear reactor, authorities scramble to cool reactors to avoid full nuclear meltdown March 15th : A second explosion occurs in reactor 4. Radiation

Toohey, Darin W.

383

A summary of North American HVDC converter station reliability specifications  

SciTech Connect (OSTI)

This paper summarizes Reliability, Availability, and Maintainability (RAM) specifications that were issued for thyristor based HVDC converter stations in service in North America. A total of twenty project specifications are summarized. A detailed summary by project is shown with specific quantitative requirements categorized. Definitions of terms, representative design principles, and formulas used in calculating RAM parameters contained in existing reliability specifications are presented.

Vancers, I. (ABB Power Systems Inc., Los Angeles, CA (United States)); Hormozi, F.J. (Los Angeles Dept. of Water and Power, CA (United States))

1993-07-01T23:59:59.000Z

384

Station GPS permanente IPG Paris DGF Uchile UNAP Iquique  

E-Print Network [OSTI]

-glue. Receptor TRIMBLE NetRS, Antenna TRIMBLE Zephyr geodetic and autonomous energy (battery and solar panel Coordinates : URCU : -21.763750 - 70.152917 DESCRIPTION North Chile II region, semi-permanent GPS station American but in the convergence area of Nazca/ SOAM plates. Approximate Position X coordinate (m) : Y

Vigny, Christophe

385

Multi-Agent Approach to Electrical Distribution Networks Control Sbastien Rumley*, Elvira Kgi*, Hugh Rudnick, Alain Germond*  

E-Print Network [OSTI]

countries, especially in Europe, deregulated their national networks, privatised significant pans of it. In particular, the integration of small size power stations in the network is problematic. These dispersed generators, presenting a very high efficiency or a minimised environmental impact (e.g. wind mills

Catholic University of Chile (Universidad Católica de Chile)

386

TANK 18 AND 19-F TIER 1A EQUIPMENT FILL MOCK UP TEST SUMMARY  

SciTech Connect (OSTI)

The United States Department of Energy (US DOE) has determined that Tanks 18-F and 19-F have met the F-Tank Farm (FTF) General Closure Plan Requirements and are ready to be permanently closed. The high-level waste (HLW) tanks have been isolated from FTF facilities. To complete operational closure they will be filled with grout for the purpose of: (1) physically stabilizing the tanks, (2) limiting/eliminating vertical pathways to residual waste, (3) discouraging future intrusion, and (4) providing an alkaline, chemical reducing environment within the closure boundary to control speciation and solubility of select radionuclides. Bulk waste removal and heel removal equipment remain in Tanks 18-F and 19-F. This equipment includes the Advance Design Mixer Pump (ADMP), transfer pumps, transfer jets, standard slurry mixer pumps, equipment-support masts, sampling masts, dip tube assemblies and robotic crawlers. The present Tank 18 and 19-F closure strategy is to grout the equipment in place and eliminate vertical pathways by filling voids in the equipment to vertical fast pathways and water infiltration. The mock-up tests described in this report were intended to address placement issues identified for grouting the equipment that will be left in Tank 18-F and Tank 19-F. The Tank 18-F and 19-F closure strategy document states that one of the Performance Assessment (PA) requirements for a closed tank is that equipment remaining in the tank be filled to the extent practical and that vertical flow paths 1 inch and larger be grouted. The specific objectives of the Tier 1A equipment grout mock-up testing include: (1) Identifying the most limiting equipment configurations with respect to internal void space filling; (2) Specifying and constructing initial test geometries and forms that represent scaled boundary conditions; (3) Identifying a target grout rheology for evaluation in the scaled mock-up configurations; (4) Scaling-up production of a grout mix with the target rheology (16 second flow cone value) from 0.25 cubic feet to 4.3 cubic feet. (Ten 0.43 cubic batches were produced because full-scale equipment was not available for the Tier 1A test.); (5) Demonstrating continuous gravity filling of the ADMP mock up test form; (6) Demonstrating continuous gravity filling of 1 inch and 2 inch schedule 40 pipe; and (7) Demonstrating filling of 1 inch and 2 inch schedule 40 pipe from the bottom up by discharging through a tube inserted into the pipes. The Tier 1A mock-up test focused on the ADMP and pipes at least one inch in diameter. The ADMP which is located in center riser of Tank 18-F is a concern because the column for this long-shaft (55 ft) pump is unique and modification to the pump prior to placing it in service limited the flow path options for filling by creating a single flow path for filling and venting the ADMP support column. The large size, vertical orientation, and complicated flow path in the ADMP warrants a detailed description of this piece of ancillary equipment.

Stefanko, D.; Langton, C.

2011-11-04T23:59:59.000Z

387

Sorption (Kd) measurements in support of dose assessments for Zion Nuclear Station Decommissioning  

SciTech Connect (OSTI)

The Zion Nuclear Power Station is being decommissioned. ZionSolutions proposes to leave much of the below grade structures in place and to fill them with “clean” concrete demolition debris from the above grade parts of the facility. This study, commissioned by ZionSolutions and conducted by the Brookhaven National Laboratory (BNL) was performed to provide site-specific data for performance assessment calculations to support the request to terminate the NRC license and allow unrestricted use of the facility. Specifically, this study measured the distribution coefficient for five radionuclides of concern using site-specific soils and groundwater. The distributions coefficient is a measure of the amount of the radionuclide that will remain sorbed to the soil or concrete that is present relative to the amount that will remain in solution. A high distribution coefficient indicates most of the radionuclide will remain on the solid material and will not be available for transport by the groundwater. The radionuclides of concern are Fe-55, Co-60, Ni-63, Sr-90, and Cs-137. Tests were performed following ASTM C1733-10, Standard Test Methods for Distribution Coefficients of Inorganic Species by the Batch Method. Sr-85 was used in the testing as an analogue for Sr-90 because it behaves similarly with respect to sorption and has a gamma emission that is easier to detect than the beta emission from Sr-90. Site-specific soils included disturbed sand (sand removed during construction and used as backfill), native sand, silt/clay and silt. In addition, concrete cores from the Unit-1 Containment Building and the Crib House were broken into particles less than 2 mm in size and tested to obtain distribution coefficients for the five nuclides.

Yim S. P.; Sullivan T.; Milian, L.

2012-12-12T23:59:59.000Z

388

Historically Black Colleges and Universities (HBCU) Solar Radiation Monitoring Network  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

The Historically Black Colleges and Universities (HBCU) Solar Radiation Monitoring Network operated from November 1985 through December 1996. The six-station network provided 5-minute averaged measurements of global and diffuse horizontal solar irradiance. The data were processed at the National Renewable Energy Laboratory (NREL) to improve the assessment of the solar radiation resources in the southeastern United States. Three of the stations also measured the direct-normal solar irradiance with a pyrheliometer mounted in an automatic sun tracker. All data are archived in the Standard Broadband Format (SBF) with quality-assessment indicators. Monthly data summaries and plots are also available for each month. In January 1997 the HBCU sites became part of the CONFRRM solar monitoring network.

389

Bending properties of epoxy resin matrix composites filled with NiMnGa ferromagnetic shape memory alloy powders  

E-Print Network [OSTI]

Bending properties of epoxy resin matrix composites filled with Ni­Mn­Ga ferromagnetic shape memory­Mn­Ga Composite materials Mechanical properties Microstructure Two types of epoxy resin matrix composites filled­Mn­Ga epoxy resin composites were reported, yet the bending property of Ni­Mn­Ga-polymer smart composites has

Zheng, Yufeng

390

Time scales and FSI in unsteady liquid-filled pipe flow Arris S Tijsseling Alan E Vardy  

E-Print Network [OSTI]

Time scales and FSI in unsteady liquid-filled pipe flow Arris S Tijsseling Alan E Vardy Department are used to classify unsteady flow in liquid-filled pipes. Seven types of pipe flow are distinguished of vibration of liquid and pipe are excited. The complexity of mathematical models describing the phenomena

Eindhoven, Technische Universiteit

391

Composites: Part B 41 (2010) 8693 86 Analysis of flexural properties of hollow-particle filled composites  

E-Print Network [OSTI]

Composites: Part B 41 (2010) 86­93 86 Analysis of flexural properties of hollow-particle filled composites G. Tagliavia, M. Porfiri1 , and N. Gupta Department of Mechanical and Aerospace Engineering properties of vinyl ester-glass hollow-particle filled composites, which are used in marine applications

Gupta, Nikhil

392

MERCURY SPECIATION SAMPLING AT NEW CENTURY ENERGY'S VALMONT STATION  

SciTech Connect (OSTI)

The 1990 Clean Air Act Amendments required the U.S. Environmental Protection Agency (EPA) to determine whether the presence of mercury in the stack emissions from fossil fuel-fired electric utility power plants poses an unacceptable public health risk. EPA's conclusions and recommendations were presented in the ''Mercury Study Report to Congress'' and ''Study of Hazardous Air Pollutant Emissions from Electric Utility Steam Generating Units''. The first report addressed both the human health and environmental effects of anthropogenic mercury emissions, while the second addressed the risk to public health posed by the emission of mercury and other hazardous air pollutants from steam electric generating units. Although these reports did not state that mercury controls on coal-fired electric power stations would be required given the current state of the art, they did indicate that the EPA views mercury as a potential threat to human health. Therefore, it was concluded that mercury controls at some point may be necessary. EPA also indicated that additional research/information was necessary before any definitive statement could be made. In an effort to determine the amount and types of mercury being emitted into the atmosphere by coal-fired power plants, EPA in late 1998 issued an information collection request (ICR) that required all coal-fired power plants to analyze their coal and submit the results to EPA on a quarterly basis. In addition, about 85 power stations were required to measure the speciated mercury concentration in the flue gas. These plants were selected on the basis of plant configuration and coal type. The Valmont Station owned and operated by New Century Energy in Boulder, Colorado, was selected for detailed mercury speciation of the flue gas as part of the ICR process. New Century Energy, in a tailored collaboration with EPRI and the U.S. Department of Energy, contracted with the Energy & Environmental Research Center (EERC) to do a study evaluating the behavior of mercury at the Valmont Station. The activities conducted at the Valmont Station by the EERC not only included the sampling needed to meet the requirements of the ICR, but involved a much more extensive mercury research program. The following objectives for the sampling at New Century Energy's Valmont Station were accomplished: (1) Successfully complete all of the mercury sampling and reporting requirements of the ICR. (2) Determine the variability in mercury concentrations at the stack using mercury continuous emission monitors (CEMs). (3) Calculate mercury mass balances and emission rates. (4) Determine the mercury concentration in the fly ash as a function of particle size. (5) Determine the impact of a fabric filter on mercury emissions for a western bituminous coal.

Dennis L. Laudal

2000-04-01T23:59:59.000Z

393

Cognitive Radio Networks as Sensor Networks  

E-Print Network [OSTI]

is used, assuming the cognitive radios know their ownfor Embedded Networked Sensing Cognitive Radio Networks AsJ. Pottie Introduction: Cognitive Radio (CR) Networks The

Bandari, Dorna; Yang, Seung R.; Zhao, Yue; Pottie, Gregory

2007-01-01T23:59:59.000Z

394

Experimental Study of High-Z Gas Buffers in Gas-Filled ICF Engines  

SciTech Connect (OSTI)

ICF power plants, such as the LIFE scheme at LLNL, may employ a high-Z, target-chamber gas-fill to moderate the first-wall heat-pulse due to x-rays and energetic ions released during target detonation. To reduce the uncertainties of cooling and beam/target propagation through such gas-filled chambers, we present a pulsed plasma source producing 2-5 eV plasma comprised of high-Z gases. We use a 5-kJ, 100-ns theta discharge for high peak plasma-heating-power, an electrode-less discharge for minimizing impurities, and unobstructed axial access for diagnostics and beam (and/or target) propagation studies. We will report on the plasma source requirements, design process, and the system design.

Rhodes, M A; Kane, J; Loosmore, G; DeMuth, J; Latkowski, J

2010-12-03T23:59:59.000Z

395

Method and apparatus for analyzing the fill characteristics of a packaging container  

DOE Patents [OSTI]

A system is described for analyzing the fill characteristics of a container. A container having a filling material therein is positioned adjacent a sound generator. Sound waves from the generator are applied to the container, causing it to vibrate. A vibration detector is used to determine the amount of container vibration. A preferred vibration detector involves a laser vibrometer which applies a reference laser beam to the vibrating container. The reference beam is reflected off of the container to generate a reflected laser beam. The reflected beam experiences a Doppler frequency shift compared with the reference beam which is caused by container vibration. The Doppler shift of the reflected beam is then compared with standardized Doppler shift data from a control container. Repeated Doppler shift measurements may also be undertaken which are converted into a vibration profile that is compared with a standardized vibration profile from a control container. 4 figs.

Rodriguez, J.G.

1998-10-13T23:59:59.000Z

396

Method and apparatus for analyzing the fill characteristics of a packaging container  

DOE Patents [OSTI]

A system for analyzing the fill characteristics of a container. A container having a filling material therein is positioned adjacent a sound generator. Sound waves from the generator are applied to the container, causing it to vibrate. A vibration detector is used to determine the amount of container vibration. A preferred vibration detector involves a laser vibrometer which applies a reference laser beam to the vibrating container. The reference beam is reflected off of the container to generate a reflected laser beam. The reflected beam experiences a Doppler frequency shift compared with the reference beam which is caused by container vibration. The Doppler shift of the reflected beam is then compared with standardized Doppler shift data from a control container. Repeated Doppler shift measurements may also be undertaken which are converted into a vibration profile that is compared with a standardized vibration profile from a control container.

Rodriguez, Julio G. (Idaho Falls, ID)

1998-01-01T23:59:59.000Z

397

Analysis of the Behavior of Electric Vehicle Charging Stations with Renewable Generations  

E-Print Network [OSTI]

Analysis of the Behavior of Electric Vehicle Charging Stations with Renewable Generations Woongsup between electric vehicle charging stations (EVCSs) with renewable electricity generation facilities (REGFs electricity generation [1]. Therefore, renewable power generation will play a significant role in smart grid

Wong, Vincent

398

Fact #832: August 4, 2014 Over Half of the Refueling Stations...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

2: August 4, 2014 Over Half of the Refueling Stations in the U.S. and Canada Sell Diesel Fuel Fact 832: August 4, 2014 Over Half of the Refueling Stations in the U.S. and Canada...

399

PRISMA Spectrometer EVR Spectra And Collection Efficiencies In Gas-Filled Mode  

SciTech Connect (OSTI)

In order to study nuclear fusion reaction, the heavy-ion magnetic spectrometer PRISMA installed at INFN Legnaro is planned to be modified to work in Gas-Filled Mode. For that purpose, the possible response of the spectrometer will be examined in Rutherford scattering experiments which simulate the fusion reaction products. predictions for the evaporation residue (EVR) position spectra and collection efficiencies, as well as the respective spectrometer set ups, as determined using the algorithm of ANAMARI code, are presented.

Dragosavac, D. R.; Ujic, P. N.; Subotic, K. M. [Institute of Nuclear Sciences VINCA, PO Box 522, 11001 Belgrade (Serbia and Montenegro); Scarlassara, F. [Universita di Padova, Padova (Italy); INFN Sezione di Padova, Padova (Italy)

2007-04-23T23:59:59.000Z

400

Hydrocarbon filling history from diagenetic evidence: Brent Group, UK North Sea  

E-Print Network [OSTI]

North Sea Mark Wilkinsona,*, R. Stuart Haszeldinea , Robert M. Ellamb , Tony E. Fallickb a Department, slow, filling phase (45­70 8C; 80­50 Ma) that formed an oil column with the oil­water contact of the present-day hydrocarbon charge was the last event in the history of the reservoir (90­100 8C; 10­0 Ma). q

Haszeldine, Stuart

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

CLOSURE OF HLW TANKS PHASE 2 FULL SCALE COOLING COILS GROUT FILL DEMONSTATIONS  

SciTech Connect (OSTI)

This report documents the Savannah River National Laboratory (SRNL) support for the Tank Closure and Technology Development (TCTD) group's strategy for closing high level radioactive waste (HLW) tanks at the Savannah River Site (SRS). Specifically, this task addresses the ability to successfully fill intact cooling coils, presently within the HLW tanks, with grout that satisfies the fresh and cured grout requirements [1] under simulated field conditions. The overall task was divided into two phases. The first phase was the development of a grout formulation that satisfies the processing requirements for filling the HLW tank cooling coils [5]. The second phase of the task, which is documented in this report, was the filling of full scale cooling coils under simulated field conditions using the grout formulation developed in the first phase. SRS Type I tank cooling coil assembly design drawings and pressure drop calculations were provided by the Liquid Waste (LW) customer to be used as the basis for configuring the test assemblies. The current concept for closing tanks equipped with internal cooling coils is to pump grout into the coils to inhibit pathways for infiltrating water. Access to the cooling coil assemblies is through the existing supply/return manifold headers located on top of the Type I tanks. The objectives for the second phase of the testing, as stated in the Task Technical and Quality Assurance plan (TTQAP) [2], were to: (1) Perform a demonstration test to assess cooling coil grout performance in simulated field conditions, and (2) Measure relevant properties of samples prepared under simulated field conditions. SRNL led the actual work of designing, fabricating and filling two full-scale cooling coil assemblies which were performed at Clemson Engineering Technologies Laboratory (CETL) using the South Carolina University Research and Education Foundation (SCUREF) program. A statement of work (SOW) was issued to CETL [6] to perform this work.

Hansen, E; Alex Cozzi, A

2008-06-19T23:59:59.000Z

402

Optimal sequencing site of hydro-power stations  

SciTech Connect (OSTI)

At the first stage of a hydro-power survey of a river, it is important to select the optimal hydro-power site. The most important condition to be satisfied is to determine the optimal site where the greatest and most economical amount of hydro-energy can be obtained. This paper proposes a new method in which the optimal arrangement of the hydro-power stations is determined by a computational operation using discrete data at points along the river such as the drainage area, altitude, and distance along the river channel as obtained from topographical maps instead of drawing on engineers` experiences and the intuitions of experts. The results by this method are then compared with data on existing hydro-power stations and the results planned by expert engineers to show that this new computational method is superior.

Hayashi, T.; Yoshino, F.; Waka, R. [Tottori Univ., Koyama (Japan). Dept. of Mechanical Engineering

1995-06-01T23:59:59.000Z

403

Navajo Generating Station and Air Visibility Regulations: Alternatives and Impacts  

SciTech Connect (OSTI)

Pursuant to the Clean Air Act, the U.S. Environmental Protection Agency (EPA) announced in 2009 its intent to issue rules for controlling emissions from Navajo Generating Station that could affect visibility at the Grand Canyon and at several other national parks and wilderness areas. The final rule will conform to what EPA determines is the best available retrofit technology (BART) for the control of haze-causing air pollutants, especially nitrogen oxides. While EPA is ultimately responsible for setting Navajo Generating Station's BART standards in its final rule, it will be the U.S. Department of the Interior's responsibility to manage compliance and the related impacts. This study aims to assist both Interior and EPA by providing an objective assessment of issues relating to the power sector.

Hurlbut, D. J.; Haase, S.; Brinkman, G.; Funk, K.; Gelman, R.; Lantz, E.; Larney, C.; Peterson, D.; Worley, C.; Liebsch, E.

2012-01-01T23:59:59.000Z

404

Polystyrene foam products equation of state as a function of porosity and fill gas  

SciTech Connect (OSTI)

An accurate EOS for polystyrene foam is necessary for analysis of numerous experiments in shock compression, inertial confinement fusion, and astrophysics. Plastic to gas ratios vary between various samples of foam, according to the density and cell-size of the foam. A matrix of compositions has been investigated, allowing prediction of foam response as a function of the plastic-to-air ratio. The EOS code CHEETAH allows participation of the air in the decomposition reaction of the foam. Differences between air-filled, Ar-blown, and CO{sub 2}-blown foams are investigated, to estimate the importance of allowing air to react with products of polystyrene decomposition. O{sub 2}-blown foams are included in some comparisons, to amplify any consequences of reaction with oxygen in air. He-blown foams are included in some comparisons, to provide an extremum of density. Product pressures are slightly higher for oxygen-containing fill gases than for non-oxygen-containing fill gases. Examination of product species indicates that CO{sub 2} decomposes at high temperatures.

Mulford, Roberta N [Los Alamos National Laboratory; Swift, Damian C [LLNL

2009-01-01T23:59:59.000Z

405

Effects of composition on the mechanical response of alumina-filled epoxy.  

SciTech Connect (OSTI)

The effect of composition on the elastic responses of alumina particle-filled epoxy composites is examined using isotropic elastic response models relating the average stresses and strains in a discretely reinforced composite material consisting of perfectly bonded and uniformly distributed particles in a solid isotropic elastic matrix. Responses for small elastic deformations and large hydrostatic and plane-strain compressions are considered. The response model for small elastic deformations depends on known elastic properties of the matrix and particles, the volume fraction of the particles, and two additional material properties that reflect the composition and microstructure of the composite material. These two material properties, called strain concentration coefficients, are characterized for eleven alumina-filled epoxy composites. It is found that while the strain concentration coefficients depend strongly on the volume fraction of alumina particles, no significant dependence on particle morphology and size is observed for the compositions examined. Additionally, an analysis of the strain concentration coefficients reveals a remarkably simple dependency on the alumina volume fraction. Responses for large hydrostatic and plane-strain compressions are obtained by generalizing the equations developed for small deformation, and letting the alumina volume fraction in the composite increase with compression. The large compression plane-strain response model is shown to predict equilibrium Hugoniot states in alumina-filled epoxy compositions remarkably well.

Montgomery, Stephen Tedford

2009-10-01T23:59:59.000Z

406

Numerical simulation of thin-shell direct drive DHe3-filled capsules fielded at OMEGA  

SciTech Connect (OSTI)

Thin-shell deuterium-helium-3 (DHe{sup 3}) filled glass capsules on the Omega laser provide a fast-implosion experimental platform for developing separate time-resolved measurements of ion, electron, and radiation temperatures in nonequilibrium plasmas. Dynamically significant non-local thermodynamic equilibrium (NLTE) conditions are created by the addition of xenon dopant to the DHe{sup 3} gas fill, in quantities sufficient to have an impact on yields, compression, and cooling rates. The high-Z dopant dramatically increases the radiative cooling rate in the plasma, allowing it to collapse in compressions that can be an order of magnitude higher than in undoped capsules. A baseline LASNEX simulation model using detailed configuration accounting NLTE atomic physics shows very good agreement with the data for doped as well as undoped capsules, while other models either underpredict or overpredict the radiative cooling enhancement. The baseline model captures the behavior of the capsule when the D:He{sup 3} ratio is varied well away from equimolar, suggesting no yield anomaly with either nearly pure deuterium or He{sup 3} fills. Variation of the electron-ion coupling in the baseline simulation model shows agreement with the data for a coupling multiplier that is within 20% of unity. Reliably inferring electron-ion coupling strength from the data is complicated by uncertainties in the hydrodynamic mix and other parameters, but many of these can be mitigated in follow-on experiments at the National Ignition Facility.

Miles, A. R.; Chung, H.-K.; Heeter, R.; Hsing, W.; Koch, J. A.; Park, H.-S.; Robey, H. F.; Scott, H. A.; Tommasini, R. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Frenje, J.; Li, C. K.; Petrasso, R. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Glebov, V. [Laboratory for Laser Energetics, University of Rochester, Rochester, New York 14623 (United States); Lee, R. W. [SLAC Linear Coherent Light Source, Menlo Park, California 94025 (United States)

2012-07-15T23:59:59.000Z

407

Evaluation of National Seismograph Network detection capabilities. Annual report, July 1994--July 1995: Volume 1  

SciTech Connect (OSTI)

This first annual report presents detection thresholds and probabilities, and location error ellipse projects for the United States National Seismic Network (USNSN) with and without cooperative stations in the eastern US. Network simulation methods are used with spectral noise levels at stations to simulate the processes of excitation, propagation, detection, and processing of seismic phases. USNSN alone should be capable of detecting 4 or more P waves for shallow crustal earthquakes in nearly all the eastern and central US at magnitude 3.8 level. When cooperative stations are added, the network should be able to detect 4 or more P waves from events 0.2 to 0.3 magnitude units lower. Planned expansion of USNSN and cooperative stations should improve detection levels by an additional 0.2-0.3 magnitudes units in many areas. Location uncertainties for USNSN can be improved by adding real-time cooperative stations. Median error ellipses for magnitude 4.5 earthquakes depend strongly on location, but uncertainties should be less than 100 km{sup 2} in the central US and degrade to 200 km{sup 2} or more offshore and sosuth and north of the international boundaries. Close cooperation with the Canadian National Network should substantially improve detection thresholds and location uncertainties along the Canadian border.

McLaughlin, K.L.; Bennett, T.J. [S-Cubed, La Jolla, CA (United States)

1996-03-01T23:59:59.000Z

408

Development of Power-head based Fan Airflow Station  

E-Print Network [OSTI]

related to the measured fan speed. Actually the measured fan speed is assumed to equal the motor synchronous speed, which is proportional to the VFD frequency. Theoretically it is not true. The difference between the synchronous speed and motor speed... the basic theory, experiment and results of the power-head based airflow station. Theory Figure 1 shows variable speed fan connection schematic. VFD is normally installed on the motor to adjust the motor speed by modulating frequency. Typically...

Wang, G.; Liu, M.

2005-01-01T23:59:59.000Z

409

Lowry Range Solar Station: Arapahoe County, Colorado (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

A partnership with industry and U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to collect solar data to support future solar power generation in the United States. The measurement station monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location. The solar measurement instrumentation is also accompanied by meteorological monitoring equipment to provide scientists with a complete picture of the solar power possibilities.

Yoder, M.; Andreas, A.

410

Nevada Power: Clark Station; Las Vegas, Nevada (Data)  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

A partnership with the University of Nevada and U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to collect solar data to support future solar power generation in the United States. The measurement station monitors global horizontal, direct normal, and diffuse horizontal irradiance to define the amount of solar energy that hits this particular location. The solar measurement instrumentation is also accompanied by meteorological monitoring equipment to provide scientists with a complete picture of the solar power possibilities.

Stoffel, T.; Andreas, A.

411

Ottawa Generating Station Biomass Facility | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy ResourcesLoading map...(UtilityCounty,Orleans County, Vermont:Ottawa County, Kansas Bennington,Station

412

Genesee Power Station LP Biomass Facility | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to: navigation, searchGeauga County, Ohio: Energy ResourcesEnergyGeneralGeneseeStation LP

413

Alternative Fuels Data Center: Ethanol Fueling Station Locations  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels Data Center Home Page onAlternativeConnecticut InformationEthanolStation

414

Effective Load Management for the City of College Station  

E-Print Network [OSTI]

to reduce the overall cost of producing and distributing power. Demand reduction comes as the result of wise manage- ment of power and therefore helps not only the con- sumer by reducing costs but also the supplier by decreasing system demand during.... The greatest impact can be achieved in communities that purchase wholesale power from a separate utility supplier and have their own billing and meter reading department, and thus a real incentive to save. DEVELOPING A ?LAN BACKGROUND College Station...

Hecox, O. D.; Bauer, V.

1985-01-01T23:59:59.000Z

415

The ALTCRISS project on board the International Space Station  

E-Print Network [OSTI]

The Altcriss project aims to perform a long term survey of the radiation environment on board the International Space Station. Measurements are being performed with active and passive devices in different locations and orientations of the Russian segment of the station. The goal is to perform a detailed evaluation of the differences in particle fluence and nuclear composition due to different shielding material and attitude of the station. The Sileye-3/Alteino detector is used to identify nuclei up to Iron in the energy range above 60 MeV/n. Several passive dosimeters (TLDs, CR39) are also placed in the same location of Sileye-3 detector. Polyethylene shielding is periodically interposed in front of the detectors to evaluate the effectiveness of shielding on the nuclear component of the cosmic radiation. The project was submitted to ESA in reply to the AO in the Life and Physical Science of 2004 and data taking began in December 2005. Dosimeters and data cards are rotated every six months: up to now three launches of dosimeters and data cards have been performed and have been returned with the end of expedition 12 and 13.

M. Casolino; F. Altamura; M. Minori; P. Picozza; C. Fuglesang; A. Galper; A. Popov; V. Benghin; V. M. Petrov; A. Nagamatsu; T. Berger; G. Reitz; M. Durante; M. Pugliese; V. Roca; L. Sihver F. Cucinotta; E. Semones; M. Shavers; V. Guarnieri; C. Lobascio; D. Castagnolo; R. Fortezza

2007-08-20T23:59:59.000Z

416

Report of Progress at the Troupe Sub-Station, Smith County Texas.  

E-Print Network [OSTI]

TEXAS AGRICULTUR 146-409-lorn [PERIMENT STATIONS BULLETIN NO. 121 FEBRUARY 1, 1909 REPORT OF PROGRESS AT THE TROUPE SUB-STATION, SMITH COUNTY, TEXAS W. H. HOTCHKISS, SUPERINTENDENT IN CHARGE POSTOFFICE COLLEGE STATION, BRAZOS COUNTY.... ..................................... C. W. CRISLER. .Chief Clerk. .................................. F. R. N~VAILLE. .Stenographer. ...................................... A. S. WARE.. .Stenographer. STATE SUBSTATIONS. ..................... H. H. HARRINGTON, Director. .College...

Hotchkiss, W.S.

1909-01-01T23:59:59.000Z

417

Technical Analysis: Integrating a Hydrogen Energy Station into a Federal Building  

E-Print Network [OSTI]

Technical Analysis: Integrating a Hydrogen Energy Station into a Federal Building Stefan Unnasch. Hydrogen Fueling Requirements Building hydrogen energy stations requires further efforts to reduce costs Energy Station The combined production of fuel cell power and hydrogen at the same facility

418

H2FIRST Reference Station Design Task: Project Deliverable 2-2  

Broader source: Energy.gov [DOE]

This H2FIRST project report, published in April 2015, presents near-term station cost results and discusses cost trends of different station types. It also contains detailed designs for five selected stations, which include piping and instrumentation diagrams, bills of materials, and several site-specific layouts.

419

Power-Optimal Scheduling for a Green Base Station with Delay Constraints  

E-Print Network [OSTI]

objective of Green Communication is to provide quality of service (QoS) at reduced energy consumptionPower-Optimal Scheduling for a Green Base Station with Delay Constraints Anusha Lalitha, Santanu with average delay constraint on the downlink of a Green Base- station. A Green Base-station is powered by both

Sharma, Vinod

420

United States Department of Agriculture / Forest Service Rocky Mountain Research Station  

E-Print Network [OSTI]

United States Department of Agriculture / Forest Service Rocky Mountain Research Station Research Collins, CO: U.S. Department of Agriculture, Forest Service, Rocky Mountain Research Station. 8 p Sciences Laboratory of the Rocky Mountain Research Station (U.S. Department of Agriculture, Forest Service

Flury, Markus

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

MAPS Stations on National Wildlife Refuges in the USFWS Pacific Region  

E-Print Network [OSTI]

MAPS Stations on National Wildlife Refuges in the USFWS Pacific Region Current Status and Future ............................................................................................. 3 Capture Rates of Adult Birds at MAPS Stations on NWR Lands .................... 3 Identifying ................................................................................. 4 Identifying Gaps in the Distribution of MAPS Stations in the Pacific Region ...... 5 Assessing

DeSante, David F.

422

Network Perspectives on Communities  

E-Print Network [OSTI]

W W. Networks Fields and Organizations: Micro-Dynamics Scaleentitled “Networks, Fields and Organizations: Micro-

Wolfe, Alvin W

2006-01-01T23:59:59.000Z

423

TANKS 18 AND 19-F STRUCTURAL FLOWABLE GROUT FILL MATERIAL EVALUATION AND RECOMMENDATIONS  

SciTech Connect (OSTI)

Cementitious grout will be used to close Tanks 18-F and 19-F. The functions of the grout are to: (1) physically stabilize the final landfill by filling the empty volume in the tanks with a non compressible material; (2) provide a barrier for inadvertent intrusion into the tank; (3) reduce contaminant mobility by (a) limiting the hydraulic conductivity of the closed tank and (b) reducing contact between the residual waste and infiltrating water; and (4) providing an alkaline, chemically reducing environment in the closed tank to control speciation and solubility of selected radionuclides. The objective of this work was to identify a single (all-in-one) grout to stabilize and isolate the residual radionuclides in the tank, provide structural stability of the closed tank and serve as an inadvertent intruder barrier. This work was requested by V. A. Chander, High Level Waste (HLW) Tank Engineering, in HLW-TTR-2011-008. The complete task scope is provided in the Task Technical and QA Plan, SRNL-RP-2011-00587 Revision 0. The specific objectives of this task were to: (1) Identify new admixtures and dosages for formulating a zero bleed flowable tank fill material selected by HLW Tank Closure Project personnel based on earlier tank fill studies performed in 2007. The chemical admixtures used for adjusting the flow properties needed to be updated because the original admixture products are no longer available. Also, the sources of cement and fly ash have changed, and Portland cements currently available contain up to 5 wt. % limestone (calcium carbonate). (2) Prepare and evaluate the placement, compressive strength, and thermal properties of the selected formulation with new admixture dosages. (3) Identify opportunities for improving the mix selected by HLW Closure Project personnel and prepare and evaluate two potentially improved zero bleed flowable fill design concepts; one based on the reactor fill grout and the other based on a shrinkage compensating flowable fill mix design. (4) Prepare samples for hydraulic property measurements for comparison to the values in the F and H- Tank Farm Performance Assessments (PAs). (5) Identify a grout mix for the Tanks 18-F and 19-F Grout Procurement Specification [Forty, 2011 a, b, c]. Results for two flowable zero bleed structural fill concepts containing 3/8 inch gravel (70070 Series and LP-8 Series) and a sand only mix (SO Series) are provided in this report. Tank Farm Engineering and SRNL Project Management selected the 70070 mix as the base case for inclusion in Revision 0 of the Tanks 18-F and 19-F grout procurement specification [Forty 2011 a] and requested admixture recommendations and property confirmation for this formulation [Forty, 2011 b]. Lower cementitious paste mixes were formulated because the 70070 mix is over designed with respect to strength and generates more heat from hydration reactions than is desirable for mass pour application. Work was also initiated on a modification of the recommended mix which included shrinkage compensation to mitigate fast pathways caused by shrinkage cracking and poor physical bonding to the tank and ancillary equipment. Testing of this option was postponed to FY12.

Stefanko, D.; Langton, C.

2011-11-01T23:59:59.000Z

424

TANKS 18 AND 19-F EQUIPMENT GROUT FILL MATERIAL EVALUATION AND RECOMMENDATIONS  

SciTech Connect (OSTI)

The United States Department of Energy (US DOE) intends to remove Tanks 18-F and 19-F at the Savannah River Site (SRS) from service. The high-level waste (HLW) tanks have been isolated from the F-area Tank Farm (FTF) facilities and will be filled with cementitious grout for the purpose of: (1) physically stabilizing the empty volumes in the tanks, (2) limiting/eliminating vertical pathways from the surface to residual waste on the bottom of the tanks, (3) providing an intruder barrier, and (4) providing an alkaline, chemical reducing environment within the closure boundary to limit solubility of residual radionuclides. Bulk waste and heel waste removal equipment will remain in Tanks 18-F and 19-F when the tanks are closed. This equipment includes: mixer pumps, transfer pumps, transfer jets, equipment support masts, sampling masts and dip tube assemblies. The current Tank 18-F and 19-F closure strategy is to grout the internal void spaces in this equipment to eliminate fast vertical pathways and slow water infiltration to the residual material on the tank floor. This report documents the results of laboratory testing performed to identify a grout formulation for filling the abandoned equipment in Tanks 18-F and 19-F. The objective of this work was to formulate a flowable grout for filling internal voids of equipment that will remain in Tanks 18-F and 19-F during the final closures. This work was requested by V. A. Chander, Tank Farm Closure Engineering, in HLW-TTR-2011-008. The scope for this task is provided in the Task Technical and Quality Assurance Plan (TTQAP), SRNL-RP-2011-00587. The specific objectives of this task were to: (1) Prepare and evaluate the SRR cooling coil grout identified in WSRC-STI-2008-00298 per the TTR for this work. The cooling coil grout is a mixture of BASF MasterFlow{reg_sign} 816 cable grout (67.67 wt. %), Grade 100 ground granulated blast furnace slag (7.52 wt. %) and water (24.81 wt. %); (2) Identify equipment grout placement and performance properties; (3) Design up to 2 additional grout systems for filling the Tank 18-F and Tank 19-F equipment; (4) Prepare samples of candidate grouts and measure fresh properties, thermal properties and cured properties; (5) Recommend a grout for the Tier 1A equipment fill mock up - ADMP 4 foot high mock up, 1 inch and 2 inch pipes; (6) Support procurement of materials for the Tier 1A equipment fill mock up test; (7) Prepare samples of the recommended grout for hydraulic property measurements which can be used for comparison to values used in the F- Tank Farm Performance Assessment (PA); and (8) Document equipment fill grout data and recommendations in a report.

Stefanko, D.; Langton, C.

2011-12-15T23:59:59.000Z

425

Tanks 18 And 19-F Structural Flowable Grout Fill Material Evaluation And Recommendations  

SciTech Connect (OSTI)

Cementitious grout will be used to close Tanks 18-F and 19-F. The functions of the grout are to: 1) physically stabilize the final landfill by filling the empty volume in the tanks with a non-compressible material; 2) provide a barrier for inadvertent intrusion into the tank; 3) reduce contaminant mobility by a) limiting the hydraulic conductivity of the closed tank and b) reducing contact between the residual waste and infiltrating water; and 4) providing an alkaline, chemically reducing environment in the closed tank to control speciation and solubility of selected radionuclides. The objective of this work was to identify a single (all-in-one) grout to stabilize and isolate the residual radionuclides in the tank, provide structural stability of the closed tank and serve as an inadvertent intruder barrier. This work was requested by V. A. Chander, High Level Waste (HLW) Tank Engineering, in HLW-TTR-2011-008. The complete task scope is provided in the Task Technical and QA Plan, SRNL-RP-2011-00587 Revision 0. The specific objectives of this task were to: 1) Identify new admixtures and dosages for formulating a zero bleed flowable tank fill material selected by HLW Tank Closure Project personnel based on earlier tank fill studies performed in 2007. The chemical admixtures used for adjusting the flow properties needed to be updated because the original admixture products are no longer available. Also, the sources of cement and fly ash have changed, and Portland cements currently available contain up to 5 wt. % limestone (calcium carbonate). 2) Prepare and evaluate the placement, compressive strength, and thermal properties of the selected formulation with new admixture dosages. 3) Identify opportunities for improving the mix selected by HLW Closure Project personnel and prepare and evaluate two potentially improved zero bleed flowable fill design concepts; one based on the reactor fill grout and the other based on a shrinkage compensating flowable fill mix design. 4) Prepare samples for hydraulic property measurements for comparison to the values in the F and H- Tank Farm Performance Assessments (PAs). 5) Identify a grout mix for the Tanks 18-F and 19-F Grout Procurement Specification [Forty, 2011 a, b, c]. Results for two flowable zero bleed structural fill concepts containing 3/8 inch gravel (70070 Series and LP#8 Series) and a sand only mix (SO Series) are provided in this report. Tank Farm Engineering and SRNL Project Management selected the 70070 mix as the base case for inclusion in Revision 0 of the Tanks 18-F and 19-F grout procurement specification [Forty 2011 a] and requested admixture recommendations and property confirmation for this formulation [Forty, 2011 b]. Lower cementitious paste mixes were formulated because the 70070 mix is over designed with respect to strength and generates more heat from hydration reactions than is desirable for mass pour application. Work was also initiated on a modification of the recommended mix which included shrinkage compensation to mitigate fast pathways caused by shrinkage cracking and poor physical bonding to the tank and ancillary equipment. Testing of this option was postponed to FY12. Mix, LP#8-16 is recommended for inclusion in the specification for furnishing and delivering tank closure grout for Tanks 18-F and 19-F [Forty, 2011 c]. A shrinkage compensating variation of this mix, LP#16C, has not been fully developed and characterized at this time.

Langton, C. A.; Stefanko, D. B.

2013-04-23T23:59:59.000Z

426

Routing in hybrid networks  

E-Print Network [OSTI]

Hybrid networks are networks that have wired as well as wireless components. Several routing protocols exist for traditional wired networks and mobile ad-hoc networks. However, there are very few routing protocols designed for hybrid networks...

Gupta, Avinash

2001-01-01T23:59:59.000Z

427

Methodology and concepts for the design of surface storage fills at the Anvil Points Oil Shale Retort Facility  

SciTech Connect (OSTI)

Primary obtectives in design of surface disposal fills for processed and raw oil shales are: (a) to insure long-term physical stability, and (b) to prevent surface runoff, surface erosion, and possible subsurface seepage from degrading the water quality of streams and ground water, it was concluded that the analysis and design of spent shale disposal fills should be based on sound geotechnical engineeering principles, considerable experience, and good judgment. An understanding of the source of variability of spent shale materials and its effect on engineering properties is a first step in developing fill design. A second important step is the assessment of long-term changes in the properties of spent shale within a disposal fill. This assessment requires consideration of possible thermal, hydrochemical, and physical interactions within the fill and between the fill and site environment. The site environment is site-specific and depends on the geological, surface and subsurface hydrological, and geotechnical characteristics of the site. The variability of spent shale materials is a direct function of variations in mineral and chemical composition of the raw shale and of the processes applied. Current technology for the design and construction of spent shale disposal fills has not been proven by experience. A major problem is the large quantities of spent shale generated for surface disposal and the lack of available sites other than large gulches in the oil shale country of the western United States. Conceptual research fill designs developed in this study should be refined and constructed to provide needed information on in situ properties and long-term performance. Research fills planned by others should be augmented to obtain needed information, especially for codisposal of spent shales with treated waste water, raw shale fines, and process dust.

Strohm, W.E. Jr.; Krinitzsky, E.L.

1983-12-01T23:59:59.000Z

428

Transport properties of partially-filled Ce{sub y}Co{sub 4}Sb{sub 12}  

SciTech Connect (OSTI)

The authors have investigated the magnetic and transport properties of Ce{sub y}Co{sub 4}Sb{sub 12} filled skutterudites with the filling fraction y {le} 0.1. These compounds are n-type materials that develop a magnetic moment upon the presence of trivalent cerium. Cerium has a strong influence on all transport properties and even in small amounts it drastically reduces the lattice thermal conductivity. The resulting figures of merit are comparable to the values established previously for the p-type filled skutterudites.

Uher, C.; Chen, B.; Hu, S.; Morelli, D.T.; Meisner, G.P.

1997-07-01T23:59:59.000Z

429

E-Print Network 3.0 - air station fallon Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

TECHNOLOGY UTC Power AFCC AC Transit Santa Clara VTA SunLine Transit Air Products Praxair Proton... future, increasing energy efficiency and reducing or eliminating air...

430

E-Print Network 3.0 - air station lemoore Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

TECHNOLOGY UTC Power AFCC AC Transit Santa Clara VTA SunLine Transit Air Products Praxair Proton... future, increasing energy efficiency and reducing or eliminating air...

431

E-Print Network 3.0 - australian antarctic station Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

EF... Monographs 32:197 Ainley DG, Fraser WR, Sullivan CW, Torres JJ, Hopkins TL, Smith WO (1986) Antarctic... , Smith WOJ, Hopkins TL, Torres JJ (1991) The structure of...

432

E-Print Network 3.0 - automatic interplanetary station Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

existence of an upstream interplanetary shock. Hence, cloud expansion Source: Richardson, John - Kavli Institute for Astrophysics and Space Research, Massachusetts Institute of...

433

E-Print Network 3.0 - atlantic generating station Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

12 On the Trail of Polar Lows Scientists from the GKSS Research Centre in Geesthacht have developed a mathematical Summary: polar lows -- in the North Atlantic. This has...

434

E-Print Network 3.0 - air force station Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

anticipates no net adverse ... Source: California Energy Commission Collection: Energy Storage, Conversion and Utilization 11 Azores Global Atmosphere Monitoring Complex...

435

E-Print Network 3.0 - air station whidbey Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

inputAtmospheric input Puget Sound air arrives... from the Pacific - veryg y clean Air pollution within PS basin can be an important pathway to deliver... ). Hydrocarbons...

436

alternative central-station technologies: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

rays is used. Photovoltaics currently relies on three technologies. Monocrystalline and polycrystalline cells are silicon-based. Thin-film cells use semi-conductor materials....

437

E-Print Network 3.0 - attract-and-kill bait stations Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

J. T. Eaton Co. Indoors TAMPER-PROOF CONTAINERS Heavy Duty Molded... Duty Galvanized Metal 910 TPR Metal ... Source: Pittendrigh, Barry - Department of Entomology, Purdue...

438

ETM (Distribution Network Automation on 10 kV cable line stations) (Smart  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address:011-DNA Jump37. It is classified as ASHRAEDuvalJusticeEPS Corp JumpESV Group JumpGrid

439

UC Davis Models: Geospatial Station Network Design Tool and Hydrogen Infrastructure Rollout Economic Analysis Model  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from theDepartment of Dept. of Energy, OfficeDepartmentDepartmentEnergyUAIEE andUC

440

E-Print Network 3.0 - accelerating rf station Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

by a 1.25-T -decay channel with phase-rotation via rf (to compress... to beam tests; Test 70-MHz rf cavity (+ 1.25-T magnet) 3 m from target; Characterize ... Source:...

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Attached algae of the Lake Erie shoreline near Nanticoke Generating Station  

SciTech Connect (OSTI)

The distribution, species composition, and standing crop of attached algae were surveyed in the splash zone along the shore of Lake Erie from 1971 to 1978 to determine the impact of construction and operation of the Nanticoke Generating Station, a coal-fired power plant. Station operation has had no apparent influence on the spatial distribution of attached algae in the lake stations. However, the discharge of heated condenser cooling water has resulted in an accelerated growth of attached algae in the immediate vicinity of the station early in the growing season, but the effect was not sustained after May. The species composition at sites near the generating station differed from control areas. Three years after the initial operation of the plant the generating station had a lower percent abundance of Cladophora and a higher percent abundance of weakly attached algal species such as Zygnema; this is perhaps attributable to the sheltered conditions in the discharge area of the generating station.

Kirby, M.K.; Dunford, W.E.

1981-11-01T23:59:59.000Z

442

Attached algae of the Lake Erie shoreline near Nanticoke generating station  

SciTech Connect (OSTI)

The distribution, species composition and standing crop of attached algae were surveyed in the splash zone along the shore of Lake Erie from 1971 to 1978 to determine the impact of construction and operation of the Nanticoke Generating Station, a coal-fired power plant. Station operation has had no apparent influence on the spatial distribution of attached algae in the lake stations. However, the discharge of heated condenser cooling water has resulted in an accelerated growth of attached algae in the immediate vicinity of the station early in the growing season, but the effect was not sustained after May. The species composition at sites near the generating station differed from control areas. Three years after the initial operation of the plant the generating station had a lower percent abundance of Cladophora and a higher percent abundance of weakly attached algal species such as Zygnema; this is perhaps attributable to the sheltered conditions in the discharge area of the generating station.

Kirby, M.K.; Dunford, W.E.

1981-01-01T23:59:59.000Z

443

Ecloud Build-Up Simulations for the FNAL MI for a Mixed Fill Pattern: Dependence on Peak SEY and Pulse Intensity During the Ramp  

E-Print Network [OSTI]

3] I. Kourbanis, "e-Clotid MI Measurements", 26 Aug. 2007. [Up Simulations for the FNAL MI for a Mixed Fill Pattern:the F N A L Main Injector (MI) for a beam fill pattern made

Furman, M. A.

2011-01-01T23:59:59.000Z

444

Renormalization group analysis of multi-band many-electron systems at half-filling  

E-Print Network [OSTI]

Renormalization group analysis for multi-band many-electron systems at half-filling at positive temperature is presented. The analysis includes the Matsubara ultra-violet integration and the infrared integration around the zero set of the dispersion relation. The multi-scale integration schemes are implemented in a finite-dimensional Grassmann algebra indexed by discrete position-time variables. In order that the multi-scale integrations are justified inductively, various scale-dependent estimates on Grassmann polynomials are established. We apply these theories in practice to prove that for the half-filled Hubbard model with nearest-neighbor hopping on a square lattice the infinite-volume, zero-temperature limit of the free energy density exists as an analytic function of the coupling constant in a neighborhood of the origin if the system contains the magnetic flux pi (mod 2 pi) per plaquette and 0 (mod 2 pi) through the large circles around the periodic lattice. Combined with Lieb's result on the flux phase problem ([Lieb, E. H., Phys. Rev. Lett. 73 (1994), 2158]), this theorem implies that the minimum free energy density of the flux phase problem converges to an analytic function of the coupling constant in the infinite-volume, zero-temperature limit. The proof of the theorem is based on a four-band formulation of the model Hamiltonian and an extension of Giuliani-Mastropietro's renormalization designed for the half-filled Hubbard model on the honeycomb lattice ([Giuliani, A. and V. Mastropietro, Commun. Math. Phys. 293 (2010), 301-346]).

Yohei Kashima

2014-08-19T23:59:59.000Z

445

A multifractal approach to space-filling recovery for PET quantification  

SciTech Connect (OSTI)

Purpose: A new image-based methodology is developed for estimating the apparent space-filling properties of an object of interest in PET imaging without need for a robust segmentation step and used to recover accurate estimates of total lesion activity (TLA). Methods: A multifractal approach and the fractal dimension are proposed to recover the apparent space-filling index of a lesion (tumor volume, TV) embedded in nonzero background. A practical implementation is proposed, and the index is subsequently used with mean standardized uptake value (SUV {sub mean}) to correct TLA estimates obtained from approximate lesion contours. The methodology is illustrated on fractal and synthetic objects contaminated by partial volume effects (PVEs), validated on realistic {sup 18}F-fluorodeoxyglucose PET simulations and tested for its robustness using a clinical {sup 18}F-fluorothymidine PET test–retest dataset. Results: TLA estimates were stable for a range of resolutions typical in PET oncology (4–6 mm). By contrast, the space-filling index and intensity estimates were resolution dependent. TLA was generally recovered within 15% of ground truth on postfiltered PET images affected by PVEs. Volumes were recovered within 15% variability in the repeatability study. Results indicated that TLA is a more robust index than other traditional metrics such as SUV {sub mean} or TV measurements across imaging protocols. Conclusions: The fractal procedure reported here is proposed as a simple and effective computational alternative to existing methodologies which require the incorporation of image preprocessing steps (i.e., partial volume correction and automatic segmentation) prior to quantification.

Willaime, Julien M. Y., E-mail: julien.willaime@siemens.com; Aboagye, Eric O. [Comprehensive Cancer Imaging Centre, Imperial College London, Hammersmith Hospital, London W12 0NN (United Kingdom); Tsoumpas, Charalampos [Division of Medical Physics, University of Leeds, LS2 9JT (United Kingdom); Turkheimer, Federico E. [Department of Neuroimaging, Institute of Psychiatry, King’s College London, London SE5 8AF (United Kingdom)

2014-11-01T23:59:59.000Z

446

Manufacturability of lab on chip devices : reagent-filled reservoirs bonding process and its effect on reagents flow pattern  

E-Print Network [OSTI]

In its lab-on-a-chip product, Daktari Diagnostics utilizes "reagent-filled reservoirs" as a means of storing and delivering the liquid reagent. During the clinical trials of the product, undesired reagent flow patterns ...

Saber, Aabed (Aabed Saud)

2013-01-01T23:59:59.000Z

447

18 IEEE Transactions onPower Delivery, Vol. 14, No.1, January 1999 Leak Location in Fluid Filled Cables  

E-Print Network [OSTI]

such as corrosion, contractor damage, effects of stray currents, and localized pipe wear due to vibrations, a pipe. Self-contained, low and medium- pressure, fluid filled cables which have an oil channel in the middle

448

Vehicles and E85 Stations Needed to Achieve Ethanol Goals  

SciTech Connect (OSTI)

This paper presents an analysis of the numbers of stations and vehicles necessary to achieve future goals for sales of ethanol fuel (E85). The paper does not analyze issues related to the supply of ethanol which may turn out to be of even greater concern. A model of consumers decisions to purchase E85 versus gasoline based on prices, availability, and refueling frequency is derived and preliminary results for 2010, 2017 and 2030 consistent with the President s 2007 biofuels program goals are presented (1). A limited sensitivity analysis is carried out to indicate key uncertainties in the trade-off between the number of stations and fuels. The analysis indicates that to meet a 2017 goal of 26 billion gallons of E85 sold, on the order of 30% to 80% of all stations may need to offer E85, and that 125 to 200 million flexible fuel vehicles (FFVs) may need to be on the road, even if oil prices remain high. These conclusions are tentative for three reasons: (1) there is considerable uncertainty about key parameter values, such as the price elasticity of choice between E85 and gasoline, (2) the future prices of E85 and gasoline are uncertain; and (3) the method of analysis used is highly aggregated; it does not consider the potential benefits of regional strategies nor the possible existence of market segments predisposed to purchase E85. Nonetheless, the preliminary results indicate that the 2017 biofuels program goals are ambitious and will require a massive effort to produce FFVs and insure widespread availability of E85.

Greene, David L [ORNL

2008-01-01T23:59:59.000Z

449

In-Situ Real Time Monitoring and Control of Mold Making and Filling Processes: Final Report  

SciTech Connect (OSTI)

This project presents a model for addressing several objectives envisioned by the metal casting industries through the integration of research and educational components. It provides an innovative approach to introduce technologies for real time characterization of sand molds, lost foam patterns and monitoring of the mold filling process. The technology developed will enable better control over the casting process. It is expected to reduce scrap and variance in the casting quality. A strong educational component is integrated into the research plan to utilize increased awareness of the industry professional, the potential benefits of the developed technology, and the potential benefits of cross cutting technologies.

Mohamed Abdelrahman; Kenneth Currie

2010-12-22T23:59:59.000Z

450

Electrical breakdown of a bubble in a water-filled capillary  

SciTech Connect (OSTI)

In this Communication, the electrical breakdown of a static bubble in a water-filled capillary generated in a dc electrical field is studied. We present experimental results which indicate that the liquid layer between capillary and bubble wall can have an important influence on the breakdown mechanism of the bubble. The breakdown electrical field (atmospheric pressure) without a liquid layer in a (vapor) bubble is 18 kV/cm. When a liquid layer is present, the electrical breakdown of an air bubble is observed at electrical fields typically two times smaller. Local plasma formation is observed in this case possibly due to bubble deformation.

Bruggeman, P.J.; Leys, C.A.; Vierendeels, J. A. [Department of Applied Physics, Research Unit Plasma Technology (RUPT), Faculty of Engineering, Ghent University, Rozier 44, B-9000 Ghent (Belgium); Department of Flow, Heat and Combustion Mechanics, Faculty of Engineering, Ghent University, Sint-Pietersnieuwstraat 41, B-9000 Ghent (Belgium)

2006-06-01T23:59:59.000Z

451

Submillimetre/TeraHertz Astronomy at Dome C with CEA filled bolometer array  

E-Print Network [OSTI]

Submillimetre/TeraHertz (e.g. 200, 350, 450 microns) astronomy is the prime technique to unveil the birth and early evolution of a broad range of astrophysical objects. A major obstacle to carry out submm observations from ground is the atmosphere. Preliminary site testing and atmospheric transmission models tend to demonstrate that Dome C could offer the best conditions on Earth for submm/THz astronomy. The CAMISTIC project aims to install a filled bolometer-array camera with 16x16 pixels on IRAIT at Dome C and explore the 200-$\\mu$m windows for potential ground-based observations.

Vincent Minier; Gilles Durand; Pierre-Olivier Lagage; Michel Talvard; Tony Travouillon; Maurizio Busso; Gino Tosti

2007-02-19T23:59:59.000Z

452

Hydrogen Fueling Station in Honolulu, Hawaii Feasibility Analysis  

SciTech Connect (OSTI)

The Department of Energy Hydrogen & Fuel Cells Program Plan (September 2011) identifies the use of hydrogen for government and fleet electric vehicles as a key step for achieving “reduced greenhouse gas emissions; reduced oil consumption; expanded use of renewable power …; highly efficient energy conversion; fuel flexibility …; reduced air pollution; and highly reliable grid-support.” This report synthesizes several pieces of existing information that can inform a decision regarding the viability of deploying a hydrogen (H2) fueling station at the Fort Armstrong site in Honolulu, Hawaii.

Porter Hill; Michael Penev

2014-08-01T23:59:59.000Z

453

List of Refueling Stations Incentives | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpInc Place:KeystoneSolarList ofPassive Solar SpaceStations Incentives

454

A High-Altitude, Station-Keeping Astronomical Platform  

E-Print Network [OSTI]

Several commercial telecommunication ventures together with a well funded US military program make it a likely possibility that an autonomous, high-altitude, light-than-air (LTA) vehicle which could maneuver and station-keep for weeks to many months will be a reality in a few years. Here I outline how this technology could be used to develop a high-altitude astronomical observing platform which could return high-resolution optical data rivaling those from space-based platforms but at a fraction of the cost.

Robert A. Fesen

2006-06-15T23:59:59.000Z

455

A High-Altitude, Station-Keeping Astronomical Platform  

E-Print Network [OSTI]

Several commercial telecommunication ventures together with a well funded US military program make it a likely possibility that an autonomous, high-altitude, light-than-air (LTA) vehicle which could maneuver and station-keep for weeks to many months will be a reality in a few years. Here I outline how this technology could be used to develop a high-altitude astronomical observing platform which could return high-resolution optical data rivaling those from space-based platforms but at a fraction of the cost.

Fesen, R A

2006-01-01T23:59:59.000Z

456

Sandia National Laboratories: Hydrogen Fueling Station Working Group  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassive SolarEducationStation Technology Infrastructure Research and

457

ARM - Evaluation Product - Station-based Surface Data Set  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcal Documentation(AVIRIS) ProductsAirborne Visible/InfraredProductsMicroPulse LIDAR CloudtheProductsStation-based

458

Kaneohe Station, Hawaii: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429 Throttled (botOpen6 ClimateKamas, Utah: EnergyKaneohe Station, Hawaii: Energy

459

Sandia National Laboratories: Oliktok Point Long Range Radar Station  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -theErik Spoerke SSLSMolten-Salt StorageNoLong Range Radar Station Sierra Unmanned

460

Alternative Fuels Data Center: Natural Gas Fueling Station Locations  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth (AOD)ProductssondeadjustsondeadjustAbout theOFFICE OFFuels inGo Map_thumbnailMississippiFloristStation

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Alternative Fuels Data Center: Propane Fueling Station Locations  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth (AOD)ProductssondeadjustsondeadjustAbout theOFFICE OFFuels inGoIndianaPennsylvania SchoolPropaneStation

462

Property:NumberOfMeasuringStations | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy ResourcesLoadingPenobscot County,ContAddr2 JumpNbrInjWellsInformationNumberOfMeasuringStations Jump

463

Toyon Power Station Biomass Facility | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to:Seadov Pty LtdSteen,Ltd JumpOperationsInformationRowleyIndianaToyon Power Station

464

Fallon Naval Air Station Geothermal Area | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address:011-DNA Jump37.California: Energy Resources Jump4748456°,Fallon Naval Air Station

465

Dilatation-strain analysis of the effects of flaws on the mechanical behavior of a highly filled elastomer  

E-Print Network [OSTI]

DILATATION-STRAIN ANALYSIS OF THE EFFECTS OF FLANS ON THE MECHANICAL BEHAVIOR OF A HIGHLY FILLED ELASTOMER A Thesis By BENJAMIN RAY SMITH Submitted to the Graduate College of the Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE August 1966 Major Subject. 'Aerospace Engineering DILATATION-STRAIN ANALYSIS OF THE EFFECTS OF FLAWS ON THE MECHANICAL BEHAVIOR OF A HIGHLY FILLED ELASTOMER A Thesis By BENJAMIN RAY SMITH Approved...

Smith, Benjamin Ray

2012-06-07T23:59:59.000Z

466

Hierarchy of fillings for FQHE in monolayer and in bilayer graphene: Explanation of $?=-\\frac{1}{2}$ fractional quantum Hall state in bilayer graphene  

E-Print Network [OSTI]

The commensurability condition is applied to determine the hierarchy of fractional fillings of Landau levels in monolayer and bilayer graphene. The filling rates for FQHE in graphene are found and illustrated in the first three Landau levels. The good agreement with the experimental data is achieved. The presence of even denominator filling fractions in the hierarchy for FQHE in bilayer graphene is explained.

Janusz Jacak; Lucjan Jacak

2015-02-04T23:59:59.000Z

467

Joint physical and numerical modeling of water distribution networks.  

SciTech Connect (OSTI)

This report summarizes the experimental and modeling effort undertaken to understand solute mixing in a water distribution network conducted during the last year of a 3-year project. The experimental effort involves measurement of extent of mixing within different configurations of pipe networks, measurement of dynamic mixing in a single mixing tank, and measurement of dynamic solute mixing in a combined network-tank configuration. High resolution analysis of turbulence mixing is carried out via high speed photography as well as 3D finite-volume based Large Eddy Simulation turbulence models. Macroscopic mixing rules based on flow momentum balance are also explored, and in some cases, implemented in EPANET. A new version EPANET code was developed to yield better mixing predictions. The impact of a storage tank on pipe mixing in a combined pipe-tank network during diurnal fill-and-drain cycles is assessed. Preliminary comparison between dynamic pilot data and EPANET-BAM is also reported.

Zimmerman, Adam; O'Hern, Timothy John; Orear, Leslie Jr.; Kajder, Karen C.; Webb, Stephen Walter; Cappelle, Malynda A.; Khalsa, Siri Sahib; Wright, Jerome L.; Sun, Amy Cha-Tien; Chwirka, J. Benjamin; Hartenberger, Joel David; McKenna, Sean Andrew; van Bloemen Waanders, Bart Gustaaf; McGrath, Lucas K.; Ho, Clifford Kuofei

2009-01-01T23:59:59.000Z

468

Hydrogen Infrastructure Market Readiness: Opportunities and Potential for Near-term Cost Reductions; Proceedings of the Hydrogen Infrastructure Market Readiness Workshop and Summary of Feedback Provided through the Hydrogen Station Cost Calculator  

SciTech Connect (OSTI)

Recent progress with fuel cell electric vehicles (FCEVs) has focused attention on hydrogen infrastructure as a critical commercialization barrier. With major automakers focused on 2015 as a target timeframe for global FCEV commercialization, the window of opportunity is short for establishing a sufficient network of hydrogen stations to support large-volume vehicle deployments. This report describes expert feedback on the market readiness of hydrogen infrastructure technology from two activities.

Melaina, M. W.; Steward, D.; Penev, M.; McQueen, S.; Jaffe, S.; Talon, C.

2012-08-01T23:59:59.000Z

469

Suppression of Beam-Ion Instability in Electron Rings with Multi-Bunch Train Beam Fillings  

SciTech Connect (OSTI)

The ion-caused beam instability in the future light sources and electron damping rings can be serious due to the high beam current and ultra-small emittance of picometer level. One simple and effective mitigation of the instability is a multi-bunch train beam filling pattern which can significantly reduce the ion density near the beam, and therefore reduce the instability growth rate up to two orders of magnitude. The suppression is more effective for high intensity beams with low emittance. The distribution and the field of trapped ions are benchmarked to validate the model used in the paper. The wake field of ion-cloud and the beam-ion instability is investigated both analytically and numerically. We derived a simple formula for the build-up of ion-cloud and instability growth rate with the multi-bunch-train filling pattern. The ion instabilities in ILC damping ring, SuperKEKB and SPEAR3 are used to compare with our analyses. The analyses in this paper agree well with simulations.

Wang, L.; Cai, Y.; Raubenheimer, T.O.; /SLAC; Fukuma, H.; /KEK, Tsukuba

2011-08-18T23:59:59.000Z

470

The evolution of a spatially homogeneous and isotropic universe filled with a collisionless gas  

E-Print Network [OSTI]

We review the evolution of a spatially homogeneous and isotropic universe described by a Friedmann-Robertson-Walker spacetime filled with a collisionless, neutral, simple, massive gas. The gas is described by a one-particle distribution function which satisfies the Liouville equation and is assumed to be homogeneous and isotropic. Making use of the isometries of the spacetime, we define precisely the homogeneity and isotropicity property of the distribution function, and based on this definition we give a concise derivation of the most general family of such distribution functions. For this family, we construct the particle current density and the stress-energy tensor and consider the coupled Einstein-Liouville system of equations. We find that as long as the distribution function is collisionless, homogenous and isotropic, the evolution of a Friedmann-Robertson-Walker universe exhibits a singular origin. Its future development depends upon the curvature of the spatial sections: spatially flat or hyperboloid universes expand forever and this expansion dilutes the energy density and pressure of the gas, while a universe with compact spherical sections reaches a maximal expansion, after which it reverses its motion and recollapses to a final crunch singularity where the energy density and isotropic pressure diverge. Finally, we analyze the evolution of the universe filled with the collisionless gas once a cosmological constant is included.

Francisco Astorga; Olivier Sarbach; Thomas Zannias

2014-06-14T23:59:59.000Z

471

The effect of mix on capsule yields as a function of shell thickness and gas fill  

SciTech Connect (OSTI)

An investigation of direct drive capsules with different shell thicknesses and gas fills was conducted to examine the amount of shock induced (Richtmyer-Meshkov) mix versus Rayleigh-Taylor mix from deceleration of the implosion. The RAGE (Eulerian) code with a turbulent mix model was used to model these capsules for neutron yields along with time-dependent mix amounts. The amount of Richtmyer-Meshkov induced mix from the shock breaking out of the shell is about 0.1??g (0.15??m of shell material), while the Rayleigh-Taylor mix is of order 1??g and determines the mixed simulation yield. The simulations were able to calculate a yield over mix (YOM) ratio (experiment/mix simulation) between 0.5 and 1.0 for capsules with shell thicknesses ranging from 7.5 to 20??m and with gas fills between 3.8 and 20?atm of D{sub 2} or DT. The simulated burn averaged T{sub ion} values typically lie with 0.5?keV of the data, which is within the measurement error. For capsules with shell thicknesses >25??m, the YOM values drop to 0.10?±?0.05, suggesting that some unmodeled effect needs to be accounted for in the thickest capsules.

Bradley, P. A., E-mail: pbradley@lanl.gov [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

2014-06-15T23:59:59.000Z

472

Phase II test plan for the evaluation of the performance of container filling systems  

SciTech Connect (OSTI)

The PHMC will provide tank wastes for final treatment by BNFL from Hanford's waste tanks. Concerns about the ability for ''grab'' sampling to provide large volumes of representative waste samples has led to the development of a nested, fixed-depth sampling system. Preferred concepts for filling sample containers that meet RCRA organic sample criteria were identified by a PHMC Decision Board. These systems will replace the needle based sampling ''T'' that is currently on the sampling system. This test plan document identifies cold tests with simulants that will demonstrate the preferred bottle filling concepts abilities to provide representative waste samples and will meet RCRA criteria. Additional tests are identified that evaluate the potential for cross-contamination between samples and the ability for the system to decontaminate surfaces which have contacted tank wastes. These tests will be performed with kaolid/water and sand/water slurry simulants in the test rig that was used by AEAT to complete Phase 1 tests in FY 1999.

BOGER, R.M.

1999-09-28T23:59:59.000Z

473

Study of high pressure gas filled RF cavities for muon collider  

E-Print Network [OSTI]

Muon collider is a considerable candidate of the next-generation high-energy lepton collider machine. Operating an RF cavity in a multi-Tesla magnet is a critical requirement in a muon accelerator and a cooling channel. However, the maximum RF gradient in a vacuum RF cavity is strongly limited by an external magnetic field. Dense hydrogen gas filled RF cavity has been proposed since it is functional of generating a high RF accelerating gradient in a strong magnetic field and making an ionization cooling process at the same time. A critical issue of the cavity is a beam- induced plasma that consumes a considerable amount of RF power. The gas filled RF test cell was made and measured the RF loading due to a beam-induced plasma by using an intense proton beam at Fermilab. By doping an electronegative gas in dense hydrogen, the plasma loading effect is significantly mitigated. The result shows that the cavity is functional with a muon collider beam. Recent progress is shown in this presentation.

Yonehara, Katsuya

2015-01-01T23:59:59.000Z

474

Optimization of Design and Manufacturing Process of Metal Foam Filled Anti-Intrusion Bars  

SciTech Connect (OSTI)

The role of an anti-intrusion bar for automotive use is to absorb the kinetic energy of the colliding bodies that is partially converted into internal work of the bodies involved in the crash. The aim of this paper is to investigate the performances of a new kind of anti-intrusion bars for automotive use, filled with metallic foams. The reason for using a cellular material as a filler deals with its capacity to absorb energy during plastic deformation, while being lightweight. The study is the evolution of a previous paper presented by the authors at Esaform 2010 and will present new results and findings. It is conducted by evaluating some key technical issues of the manufacturing problem and by conducting experimental and numerical analyses. The evaluation of materials and shapes of the closed sections to be filled is made in the perspective of a car manufacturer (production costs, weight reduction, space availability in a car door, etc.). Experimentally, foams are produced starting from an industrial aluminium precursor with a TiH{sub 2} blowing agent. Bars are tested in three point bending, in order to evaluate their performances in terms of force-displacement response and other specific performance parameters. In order to understand the role of interface between the inner surface of the tube and the external surface of the foam, different kinds of interface are tested.

Villa, Andrea; Mussi, Valerio [Laboratorio MUSP-via Turotti 9, 29122 Piacenza (Italy); Strano, Matteo [Politecnico di Milano-Dipartimento di Meccanica, via La Masa 1, 20156, Milan (Italy)

2011-05-04T23:59:59.000Z

475

United States Historical Climatology Network (US HCN) monthly temperature and precipitation data  

SciTech Connect (OSTI)

This document describes a database containing monthly temperature and precipitation data for 1221 stations in the contiguous United States. This network of stations, known as the United States Historical Climatology Network (US HCN), and the resulting database were compiled by the National Climatic Data Center, Asheville, North Carolina. These data represent the best available data from the United States for analyzing long-term climate trends on a regional scale. The data for most stations extend through December 31, 1994, and a majority of the station records are serially complete for at least 80 years. Unlike many data sets that have been used in past climate studies, these data have been adjusted to remove biases introduced by station moves, instrument changes, time-of-observation differences, and urbanization effects. These monthly data are available free of charge as a numeric data package (NDP) from the Carbon Dioxide Information Analysis Center. The NDP includes this document and 27 machine-readable data files consisting of supporting data files, a descriptive file, and computer access codes. This document describes how the stations in the US HCN were selected and how the data were processed, defines limitations and restrictions of the data, describes the format and contents of the magnetic media, and provides reprints of literature that discuss the editing and adjustment techniques used in the US HCN.

Daniels, R.C. [ed.] [Univ. of Tennessee, Knoxville, TN (United States). Energy, Environment and Resources Center] [ed.; Univ. of Tennessee, Knoxville, TN (United States). Energy, Environment and Resources Center; Boden, T.A. [ed.] [Oak Ridge National Lab., TN (United States)] [ed.; Oak Ridge National Lab., TN (United States); Easterling, D.R.; Karl, T.R.; Mason, E.H.; Hughes, P.Y.; Bowman, D.P. [National Climatic Data Center, Asheville, NC (United States)] [National Climatic Data Center, Asheville, NC (United States)

1996-01-11T23:59:59.000Z

476

A prototype station for ARIANNA: a detector for cosmic neutrinos  

E-Print Network [OSTI]

The Antarctic Ross Iceshelf Antenna Neutrino Array (ARIANNA) is a proposed detector for ultra-high energy astrophysical neutrinos. It will detect coherent radio Cherenkov emission from the particle showers produced by neutrinos with energies above about 10^17 eV. ARIANNA will be built on the Ross Ice Shelf just off the coast of Antarctica, where it will eventually cover about 900 km^2 in surface area. There, the ice-water interface below the shelf reflects radio waves, giving ARIANNA sensitivity to downward going neutrinos and improving its sensitivity to horizontally incident neutrinos. ARIANNA detector stations will each contain 4-8 antennas which search for brief pulses of 50 MHz to 1 GHz radio emission from neutrino interactions. We describe a prototype station for ARIANNA which was deployed in Moore's Bay on the Ross Ice Shelf in December 2009, discuss the design and deployment, and present some initial figures on performance. The ice shelf thickness was measured to be 572 +/- 6 m at the deployment site.

Lisa Gerhardt; Spencer R. Klein; Thorsten Stezelberger; Steve Barwick; Kamlesh Dookayka; Jordan Hanson; Ryan Nichol

2010-05-27T23:59:59.000Z

477

National Atmospheric Deposition Program (NADP) Networks: Data on the chemistry of precipitation  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

The National Atmospheric Deposition Program/National Trends Network (NADP/NTN) is a nationwide network of sites collecting data on the chemistry of precipitation for monitoring of geographical and temporal long-term trends. The precipitation at each station is collected weekly according to strict clean-handling procedures. It is then sent to the Central Analytical Laboratory where it is analyzed for hydrogen (acidity as pH), sulfate, nitrate, ammonium, chloride, and base cations (such as calcium, magnesium, potassium and sodium). The network is a cooperative effort between many different groups, including the State Agricultural Experiment Stations, U.S. Geological Survey, U.S. Department of Agriculture, and numerous other governmental and private entities. DOE is one of these cooperating agencies, though it plays a smaller funding role than some of the other federal sources. Since 1978, the NADP/NTN has grown from 22 stations to over 250 sites spanning the continental United States, Alaska, and Puerto Rico, and the Virgin Islands. The National Atmospheric Deposition Program has also expanded its sampling to two additional networks: 1) the Mercury Deposition Network (MDN), currently with over 90 sites, was formed in 1995 to collect weekly samples of precipitation which are analyzed by Frontier Geosciences for total mercury, and 2) the Atmospheric Integrated Research Monitoring Network (AIRMoN), formed for the purpose of studying precipitation chemistry trends with greater temporal resolution than the NTN. [taken from the NADP History and Overview page at http://nadp.sws.uiuc.edu/nadpoverview.asp] Data from these networks are freely available in via customized search interfaces linked to interactive maps of the stations in the three networks. Animated Isopleth maps in Flash and PowerPoint are also available to display concentrations and depositions various substances such as sulfate, nitrate, etc. (Specialized Interface)

478

Microgravity exploration for a sediment-filled channel intersecting a near-surface lignite seam  

E-Print Network [OSTI]

lignite seam. A 1900 foot line running north and south was located such that 1) the south end was at the location of a core which found 8 feet of lignite at a depth of 60 feet and 2) the north end was at the location of a core which found no nea... of anomalies to the full extent possible with the meter. Selection of the Station Locations A 1900 foot line running north and south was located such that 1) the south end was at the location of a core which found 8 feet of lignite at a depth of 60 feet. 2...

May, Clifford John

1984-01-01T23:59:59.000Z

479

Reactor Vessel and Reactor Vessel Internals Segmentation at Zion Nuclear Power Station - 13230  

SciTech Connect (OSTI)

Zion Nuclear Power Station (ZNPS) is a dual-unit Pressurized Water Reactor (PWR) nuclear power plant located on the Lake Michigan shoreline, in the city of Zion, Illinois approximately 64 km (40 miles) north of Chicago, Illinois and 67 km (42 miles) south of Milwaukee, Wisconsin. Each PWR is of the Westinghouse design and had a generation capacity of 1040 MW. Exelon Corporation operated both reactors with the first unit starting production of power in 1973 and the second unit coming on line in 1974. The operation of both reactors ceased in 1996/1997. In 2010 the Nuclear Regulatory Commission approved the transfer of Exelon Corporation's license to ZionSolutions, the Long Term Stewardship subsidiary of EnergySolutions responsible for the decommissioning of ZNPS. In October 2010, ZionSolutions awarded Siempelkamp Nuclear Services, Inc. (SNS) the contract to plan, segment, remove, and package both reactor vessels and their respective internals. This presentation discusses the tools employed by SNS to remove and segment the Reactor Vessel Internals (RVI) and Reactor Vessels (RV) and conveys the recent progress. SNS's mechanical segmentation tooling includes the C-HORCE (Circumferential Hydraulically Operated Cutting Equipment), BMT (Bolt Milling Tool), FaST (Former Attachment Severing Tool) and the VRS (Volume Reduction Station). Thermal segmentation of the reactor vessels will be accomplished using an Oxygen- Propane cutting system. The tools for internals segmentation were designed by SNS using their experience from other successful reactor and large component decommissioning and demolition (D and D) projects in the US. All of the designs allow for the mechanical segmentation of the internals remotely in the water-filled reactor cavities. The C-HORCE is designed to saw seven circumferential cuts through the Core Barrel and Thermal Shield walls with individual thicknesses up to 100 mm (4 inches). The BMT is designed to remove the bolts that fasten the Baffle Plates to the Baffle Former Plates. The FaST is designed to remove the Baffle Former Plates from the Core Barrel. The VRS further volume reduces segmented components using multiple configurations of the 38i and horizontal reciprocating saws. After the successful removal and volume reduction of the Internals, the RV will be segmented using a 'First in the US' thermal cutting process through a co-operative effort with Siempelkamp NIS Ingenieurgesellschaft mbH using their experience at the Stade NPP and Karlsruhe in Germany. SNS mobilized in the fall of 2011 to commence execution of the project in order to complete the RVI segmentation, removal and packaging activities for the first unit (Unit 2) by end of the 2012/beginning 2013 and then mobilize to the second unit, Unit 1. Parallel to the completion of the segmentation of the reactor vessel internals at Unit 1, SNS will segment the Unit 2 pressure vessel and at completion move to Unit 1. (authors)

Cooke, Conrad; Spann, Holger [Siempelkamp Nuclear Services: 5229 Sunset Blvd., (Suite M), West Columbia, SC, 29169 (United States)] [Siempelkamp Nuclear Services: 5229 Sunset Blvd., (Suite M), West Columbia, SC, 29169 (United States)

2013-07-01T23:59:59.000Z

480

Daily Reporting Rainfall Station THOMSON-BARCOO RIVERS  

E-Print Network [OSTI]

WARNING NETWORK Major Roads Railway Digital data supplied Geoscience Australia. All rights reservedCorkCorkCorkCorkCorkCorkCorkCork Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R Western R

Greenslade, Diana

Note: This page contains sample records for the topic "filling station networks" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Station GPS permanente IPG Paris DGF Uchile UNAP Iquique.  

E-Print Network [OSTI]

working hours telephone nearby NONO Electric power nearby NONO Autonomous energy ­ (solar panel, regulator , Colchane Chile) Author : Socquet / Carrizo Site Code : COLC Date installation : 2007 11 04 Coordinates from IPGP / DGF network MONUMENTATION Antenna located in the top of the scholar library building, basic

Vigny, Christophe

482

Control method for high-pressure hydrogen vehicle fueling station dispensers  

DOE Patents [OSTI]

A method for quick filling a vehicle hydrogen storage vessel with hydrogen, the key component of which is an algorithm used to control the fill process, which interacts with the hydrogen dispensing apparatus to determine the vehicle hydrogen storage vessel capacity.

Kountz, Kenneth John; Kriha, Kenneth Robert; Liss, William E.

2006-06-13T23:59:59.000Z

483

Radio Frequency Station - Beam Dynamics Interaction in Circular Accelerators  

SciTech Connect (OSTI)

The longitudinal beam dynamics in circular accelerators is mainly defined by the interaction of the beam current with the accelerating Radio Frequency (RF) stations. For stable operation, Low Level RF (LLRF) feedback systems are employed to reduce coherent instabilities and regulate the accelerating voltage. The LLRF system design has implications for the dynamics and stability of the closed-loop RF systems as well as for the particle beam, and is very sensitive to the operating range of accelerator currents and energies. Stability of the RF loop and the beam are necessary conditions for reliable machine operation. This dissertation describes theoretical formalisms and models that determine the longitudinal beam dynamics based on the LLRF implementation, time domain simulations that capture the dynamic behavior of the RF station-beam interaction, and measurements from the Positron-Electron Project (PEP-II) and the Large Hadron Collider (LHC) that validate the models and simulations. These models and simulations are structured to capture the technical characteristics of the system (noise contributions, non-linear elements, and more). As such, they provide useful results and insight for the development and design of future LLRF feedback systems. They also provide the opportunity to study diverse longitudinal beam dynamics effects such as coupled-bunch impedance driven instabilities and single bunch longitudinal emittance growth. Coupled-bunch instabilities and RF station power were the performance limiting effects for PEP-II. The sensitivity of the instabilities to individual LLRF parameters, the effectiveness of alternative operational algorithms, and the possible tradeoffs between RF loop and beam stability were studied. New algorithms were implemented, with significant performance improvement leading to a world record current during the last PEP-II run of 3212 mA for the Low Energy Ring. Longitudinal beam emittance growth due to RF noise is a major concern for LHC. Simulations studies and measurements were conducted that clearly show the correlation between RF noise and longitudinal bunch emittance, identify the major LLRF noise contributions, and determine the RF component dominating this effect. With these results, LHC upgrades and alternative algorithms are evaluated to reduce longitudinal emittance growth during operations. The applications of this work are described with regard to future machines and analysis of new technical implementations, as well as to possible future work which would continue the directions of this dissertation.

Mastoridis, Themistoklis; /Stanford U., Elect. Eng. Dept. /SLAC

2011-03-01T23:59:59.000Z

484

Regulations, Codes, and Standards (RCS) Template for California Hydrogen Dispensing Stations  

SciTech Connect (OSTI)

This report explains the Regulations, Codes, and Standards (RCS) requirements for hydrogen dispensing stations in the State of California. The reports shows the basic components of a hydrogen dispensing station in a simple schematic drawing; the permits and approvals that would typically be required for the construction and operation of a hydrogen dispensing station; and a basic permit that might be employed by an Authority Having Jurisdiction (AHJ).

Rivkin, C.; Blake, C.; Burgess, R.; Buttner, W.; Post, M.

2012-11-01T23:59:59.000Z

485

Constraint-based Evolutionary QoS Adaptation for Power Utility Communication Networks  

E-Print Network [OSTI]

Champrasert, Junichi Suzuki and Tetsuo Otani Department of Computer Science University of Massachusetts power stations to consumers through a number of substations. Recently, the commu- nication networks consumers through a chain of substations. Each substation is re- sponsible for a certain physical regio

Suzuki, Jun

486

A Pricing Based Algorithm for Cell Switching Off in Green Cellular Networks  

E-Print Network [OSTI]

A Pricing Based Algorithm for Cell Switching Off in Green Cellular Networks Ali Yildiz and Tolga--In this study, we propose a pricing based algorithm that assigns user terminals (UTs) to base stations (BSs) and optimizes the transmission powers in a way that minimizes the energy expenditure. The algorithm takes

Yanikomeroglu, Halim

487

Testing for fault activity at Yucca Mountain, Nevada, using independent GPS results from the BARGEN network  

E-Print Network [OSTI]

Testing for fault activity at Yucca Mountain, Nevada, using independent GPS results from the BARGEN June 2006; published 19 July 2006. [1] Data from BARGEN GPS stations around Yucca Mountain (YM) have at Yucca Mountain, Nevada, using independent GPS results from the BARGEN network, Geophys. Res. Lett., 33

Blewitt, Geoffrey

488

Modeling of a Cooperative One-Dimensional Multi-Hop Network using Quasi-Stationary Markov  

E-Print Network [OSTI]

Syed Ali Hassan and Mary Ann Ingram School of Electrical and Computer Engineering Georgia Institute the irreducible discrete time Markov chain, with one absorbing state, as a potential candidate to model a wireless Station or Access Point transmissions, harnessing the other radios in a network to increase

Ingram, Mary Ann

489

An Integral Flow-Based Energy-Efficient Routing Algorithm for Wireless Sensor Networks  

E-Print Network [OSTI]

An Integral Flow-Based Energy-Efficient Routing Algorithm for Wireless Sensor Networks Shashidhar. As sensor nodes are energy-constrained, energy-efficient routing is essential for increasing the lifetime. In this paper, we consider static base stations and propose an algorithmic approach to obtain integral energy-efficient

Prakash, Ravi

490

IEEE Network September/October 200018 ver the past few years, there has been tremen-  

E-Print Network [OSTI]

-way paging, mobile satellite, etc.) into a seamless radio infrastructure capable of offering a wide range network (PCN) is being standard- ized as part of the International Mobile Telecommunications 2000 (IMT via the base stations. Cells can have dif- ferent sizes: picocells are commonly used in indoor

Wong, Vincent

491

DESIGNING AN OPPORTUNITY FUEL WITH BIOMASS AND TIRE-DERIVED FUEL FOR COFIRING AT WILLOW ISLAND GENERATING STATION AND COFIRING SAWDUST WITH COAL AT ALBRIGHT GENERATING STATION  

SciTech Connect (OSTI)

During the period October 1, 2003-December 31, 2003, Allegheny Energy Supply Co., LLC (Allegheny) continued with demonstration operations at the Willow Island Generating Station and improvements to the Albright Generating Station cofiring systems. The demonstration operations at Willow Island were designed to document integration of biomass cofiring into commercial operations, including evaluating new sources of biomass supply. The Albright improvements were designed to increase the resource base for the projects, and to address issues that came up during the first year of operations. This report summarizes the activities associated with the Designer Opportunity Fuel program, and demonstrations at Willow Island and Albright Generating Stations.

K. Payette; D. Tillman

2004-01-01T23:59:59.000Z

492

Next Generation Hydrogen Station Composite Data Products: Data through Quarter 4 of 2013  

SciTech Connect (OSTI)

This report includes 25 composite data products (CDPs) produced for next generation hydrogen stations, with data through quarter 4 of 2013.

Sprik, S.; Kurtz, J.; Peters, M.

2014-05-01T23:59:59.000Z

493

FEMP ESPC Success Story- U.S. Naval Station, Guantanamo Bay, Cuba  

Broader source: Energy.gov [DOE]

Fact sheet describes the Energy Savings Performance Contract (ESPC) success story on environmental stewardship and cost savings at the U.S. Naval Station at Guantanamo Bay, Cuba.

494

Uncertainty for Satellite and Station Solar Data in the Updated NSRDB  

SciTech Connect (OSTI)

Solar Resource Assessment Workshop, Denver CO, Oct 29, 2008 presentation: Uncertainty for Satellite and Station Solar Data in the Updated NSRDB,

Myers, D. R.

2008-10-29T23:59:59.000Z

495

Next Generation Hydrogen Stations: All Composite Data Products through Fall 2012  

SciTech Connect (OSTI)

This presentation from the U.S. Department of Energy's National Renewable Energy Laboratory includes 14 composite data products (CDPs) for next generation hydrogen stations.

Sprik, S.; Wipke, K.; Ramsden, T.; Ainscough, C.; Kurtz, J.

2012-10-01T23:59:59.000Z

496

Clean Cities Launches iPhone App for Alternative Fueling Station...  

Office of Environmental Management (EM)

free app that locates fueling stations offering alternative fuels, including electricity, natural gas, biodiesel, E85, propane, and hydrogen. The National Renewable Energy...

497

Acceptance test report, 241-AW air inlet filter station pressure decay test  

SciTech Connect (OSTI)

This is the acceptance test report for pressure decay tests performed on newly-installed 241-AW Tank Farm primary ventilation system air inlet filter stations.

Tuck, J.A.

1996-02-21T23:59:59.000Z

498

Converting Limbo Lands to Energy-Generating Stations: Renewable Energy Technologies on Underused, Formerly Contaminated Sites  

SciTech Connect (OSTI)

This report addresses the potential for using 'Limbo Lands' (underused, formerly contaminated sites, landfills, brownfields, abandoned mine lands, etc. ) as sites for renewable energy generating stations.

Mosey, G.; Heimiller, D.; Dahle, D.; Vimmerstedt, L.; Brady-Sabeff, L.

2007-10-01T23:59:59.000Z

499

Bibliography on overvoltage protection and insulation coordination of HVDC converter stations, 1979-1989  

SciTech Connect (OSTI)

This bibliography is a listing of references on the subject of overvoltage protection and insulation coordination of HVDC converter stations, for the years 1979 through 1989.

Not Available

1991-04-01T23:59:59.000Z

500

SNL Issues a Request for Quotation for a Hydrogen Station Test...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

for Quotation for a Hydrogen Station Test Device DOE Issues Request for Quotations for Depleted Uranium Hexafluoride Conversion Technical Services 10 Questions Regarding SAE...