Sample records for femp designated product

  1. FEMP Designated Product: Lavatory Faucets

    Broader source: Energy.gov [DOE]

    FEMP suspended its product designation and purchasing specification for commercial faucets until further notice.

  2. FEMP Designated Product Assessment for Commercial Gas Water Heaters

    E-Print Network [OSTI]

    Lutz, Jim

    2012-01-01T23:59:59.000Z

    price for a condensing commercial water heater is $1,579.For condensing commercial water heaters with a thermalFound products for water heater in any product field and gas

  3. FEMP News | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    FEMP News FEMP News October 10, 2014 Energy Department Issues Green Building Certification System Final Rule to Support Increased Energy Measurement and Efficient Building Design...

  4. FEMP Updates Product Energy-Efficiency Requirements | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFICPracticesFEMP UESCUpdates

  5. Residential Dishwashers, Purchasing Specifications for Energy-Efficient Products (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-06-01T23:59:59.000Z

    Performance and purchasing specifications for residential dishwashers under the FEMP-designated product program.

  6. Clothes Washers, Purchasing Specifications for Energy-Efficient Products (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-06-01T23:59:59.000Z

    Performance and purchasing specifications for residential clothes washers under the FEMP-designated product program.

  7. Commercial Gas Water Heaters, Purchasing Specifications for Energy-Efficient Products (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-09-01T23:59:59.000Z

    Performance and purchasing specifications for commercial gas water heaters under the FEMP-designated product program.

  8. Covered Product Categories (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2012-02-01T23:59:59.000Z

    List of Federal Energy Management Program (FEMP)-designated product categories for energy-efficient procurement requirements.

  9. New National Conservation Training Center a model of energy-efficient design: FEMP technical assistance case study fact sheet

    SciTech Connect (OSTI)

    Atkison, K.

    1998-10-07T23:59:59.000Z

    This FEMP technical assistance case study shows that energy efficiency, cost effectiveness, and aesthetics can be incorporated into the design of a Federal facility--in this case the National Conservation Training Center in Shepherdstown, WV, which encompasses many buildings with a variety of purposes.

  10. Covered Product Categories (Fact Sheet), Energy-Efficient Product...

    Broader source: Energy.gov (indexed) [DOE]

    Legend of Energy-Efficient Product Programs n ENERGY STAR p FEMP-Designated u FEMP Low Standby Power l Electronic Product Environmental Assessment Tool (EPEAT) WaterSense...

  11. Covered Product Categories (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2014-04-01T23:59:59.000Z

    Federal mandates require that Federal agencies purchase energy-efficient products. To help agency buyers meet these requirements, the Federal Energy Management Program (FEMP) maintains a list of FEMP-designated and ENERGY STAR-qualified product categories.

  12. FEMP Designated Product Assessment for Commercial Gas Water Heaters

    E-Print Network [OSTI]

    Lutz, Jim

    2012-01-01T23:59:59.000Z

    heaters, hot water supply boilers, and unfired hot water storage tanks.heaters, hot water supply boilers, and unfired hot water storage tanks.

  13. FEMP Designated Product Assessment for Commercial Gas Water Heaters

    E-Print Network [OSTI]

    Lutz, Jim

    2012-01-01T23:59:59.000Z

    resistance and heat pump water heaters are not covered.other than commercial heat pump water heaters). 10CFR431.110

  14. FEMP Designated Product Assessment for Commercial Gas Water Heaters

    E-Print Network [OSTI]

    Lutz, Jim

    2012-01-01T23:59:59.000Z

    rating of at least 4000 Btu per hour per gallon of storedpackaged boiler that has an input rating from 300,000 Btu/hrto 12,500,000 Btu/hr (and at least 4,000 Btu/hr per gallon

  15. FEMP Fiscal Year 1999 ESPC Business Strategy Development Summary Report

    SciTech Connect (OSTI)

    Mcmordie, Katherine; Hunt, W. D.

    2000-03-03T23:59:59.000Z

    This report summarizes the objectives, activities, products, and recommendations of the ESPC Business Strategy Development project. The objective of this project was to assist DOE FEMP in defining the potential Federal sector market for FEMP-offered alternative financing services with a focus on Super-Energy Savings Performance Contracts (Super-ESPCs).

  16. FEMP Certified Training Program

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy's Federal Energy Management Program (FEMP) works with key individuals to accomplish energy change within organizations by bringing expertise from all levels of project...

  17. FEMP program overview

    SciTech Connect (OSTI)

    Epstein, K.

    1999-07-01T23:59:59.000Z

    The Federal Energy Management Program (FEMP), part of the U.S. Department of Energy, helps agencies reduce their costs, increase energy efficiency, use renewable energy, and conserve water.

  18. Covered Product Category: Fluorescent Ballasts

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and federal efficiency requirements across a variety of product categories, including fluorescent ballasts, which is a FEMP designated product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  19. FEMP News | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    November 19, 2013 FEMP Presents Its Newest On-Demand eTraining Course on Building Automation Systems The U.S. Department of Energy (DOE) Federal Energy Management Program (FEMP)...

  20. Covered Product Category: Commercial Boilers

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance and Federal efficiency requirements for commercial boilers, which is a FEMP-designated product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  1. Covered Product Category: Exterior Lighting

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance and Federal efficiency requirements for outdoor wall-mounted light fixtures or luminaires, outdoor pole/arm-mounted area and roadway luminaires, outdoor pole/arm-mounted decorative luminaires, fuel pump canopy luminaires, bollards, and parking garage luminaires, all of which are FEMP-designated product categories.

  2. Covered Product Category: Pre-Rinse Spray Valves

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including pre-rinse spray valves, which are a FEMP-designated product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  3. Covered Product Category: Water-Cooled Electric Chillers

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including water-cooled electric chillers, which is a FEMP-designated product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  4. Federal Energy Management Program (FEMP) Technical Assistance...

    Energy Savers [EERE]

    Federal Energy Management Program (FEMP) Technical Assistance Request Portal User Guide Federal Energy Management Program (FEMP) Technical Assistance Request Portal User Guide...

  5. FEMP Washington Update

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFICPracticesFEMP

  6. Covered Product Category: Air-Cooled Electric Chillers

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements for electric chillers, which are a FEMP-designated product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  7. FEMP Renewable Energy Overview

    SciTech Connect (OSTI)

    Not Available

    2003-06-01T23:59:59.000Z

    This four-page overview describes how Federal agencies can contact the Department of Energy's Federal Energy Management Program (FEMP) to obtain assistance in acquiring renewable energy systems, renewable fuels, and renewable ("green") power for use in their facilities and vehicles. Renewable resources, technologies, and fuels are described, as well as Federal goals for using clean, sustainable renewable energy; the current goal is to supply 2.5% of the Federal Government's energy with renewable sources by 2005. Also included is a description of the resources and technologies themselves and associated benefits.

  8. What`s new in federal energy management: FEMP program overview. FEMP Renewable Energy Program

    SciTech Connect (OSTI)

    NONE

    1996-08-01T23:59:59.000Z

    As the owner or manager of more than 500,000 facilities, the US government has a superb opportunity to reduce fuel imports and improve environmental quality by using renewable sources of energy. In many Federal applications -- such as irrigation, water heating, indoor and outdoor lighting, or communications -- commercially available renewable technologies are often the most cost-effective option for supplying the needed energy, and they are environmentally friendly. The US Department of Energy, Federal Energy Management Program (FEMP) helps Federal agencies take advantage of the benefits offered by renewable technologies and apply the renewable provisions of the Energy Policy Act (EPAct) and Executive Order 12902. FEMP`s Renewable Energy Program educates Federal agencies about renewable opportunities and helps agencies implement successful renewable projects. And the opportunities are abundant. In new construction projects, for example, planners can optimize facility energy performance by incorporating renewable energy and energy efficiency measures early in the design process. Renewables are cost-effective in many retrofit projects. They are the clear choice for many remote sites that utility-supplied power does not reach. Their environmental advantages include either zero or reduced air emissions compared with conventional energy sources and no risk of fuel spills.

  9. The FEMP Awards Program: Fostering Institutional Change and Energy...

    Office of Environmental Management (EM)

    The FEMP Awards Program: Fostering Institutional Change and Energy Management Excellence The FEMP Awards Program: Fostering Institutional Change and Energy Management Excellence...

  10. Environmental Management Assessment of the Fernald Environmental Management Project (FEMP)

    SciTech Connect (OSTI)

    Not Available

    1993-04-01T23:59:59.000Z

    This report documents the results of the Environmental Management Assessment performed at the Fernald Environmental Management Project (FEMP) in Fernald, Ohio. During this assessment, the activities conducted by the assessment team included review of internal documents and reports from previous audits and assessments; interviews with US Department of Energy (DOE) and FEMP contractor personnel; and inspection and observation of selected facilities and operations. The onsite portion of the assessment was conducted from March 15 through April 1, 1993, by DOE`s Office of Environmental Audit (EH-24) located within the Office of the Assistant Secretary for Environment, Safety, and Health (EH-1). EH-24 carries out independent assessments of DOE facilities and activities as part of the EH-1 Environment, Safety, and Health (ES&H) Oversight Audit Program. The EH-24 program is designed to evaluate the status of DOE facilities and activities with respect to compliance with Federal, state, and local environmental laws and regulations; compliance with DOE Orders, Guidance and Directives; conformance with accepted industry practices and standards of performance; and the status and adequacy of management systems developed to address environmental requirements. The Environmental Management Assessment of FEMP focused on the adequacy of environmental management systems. Further, in response to requests by the Office of Environmental Restoration and Waste Management (EM) and Fernald Field Office (FN), Quality Assurance and Environmental Radiation activities at FEMP were evaluated from a programmatic standpoint. The results of the evaluation of these areas are contained in the Environmental Protection Programs section in this report.

  11. DOE/FEMP Welcome and Announcements

    Energy Savers [EERE]

    Federal Utility Partnership Working Group Seminar: DOEFEMP Welcome and Announcements October 5, 2014 David McAndrew Utility Project Lead DOE FEMP 2 Welcome To Fall FUPWG Thank...

  12. FEMP O&M Program | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    O&M Program FEMP O&M Program Presentation covers the FEMP O&M Program, given at the Spring 2010 Federal Utility Partnership Working Group (FUPWG) meeting in Providence, Rhode...

  13. FEMP Helps Federal Facilities Develop Large-Scale Renewable Energy...

    Office of Environmental Management (EM)

    FEMP Helps Federal Facilities Develop Large-Scale Renewable Energy Projects FEMP Helps Federal Facilities Develop Large-Scale Renewable Energy Projects August 21, 2013 - 12:00am...

  14. FEMP (Federal Energy Management Program) Update, Spring 1989

    SciTech Connect (OSTI)

    Not Available

    1989-04-01T23:59:59.000Z

    The FEMP Update, published quarterly by the Federal Energy Management Program (FEMP), provides information that will assist federal managers in their energy management responsibilities. The Update is distributed primarily to federal facility and energy management personnel.

  15. What`s new in federal energy management: FEMP program overview. Federal Energy Management Program

    SciTech Connect (OSTI)

    NONE

    1996-08-01T23:59:59.000Z

    The US government has an enormous cost-saving opportunity as the largest energy user in the world. In 1994, the government spent $8 billion for its 500,000 buildings, it vehicles, and process energy. The US Department of Energy (DOE), Federal Energy Management Program (FEMP) reduces the cost of government and makes it work better through energy efficiency, use of renewable energy, and water conservation. FEMP leads Federal energy efficiency efforts and helps Federal energy managers identify and procure the best, most cost-effective energy-saving projects. It does this through proactive problem solving; an aggressive emphasis on increasing the number and quality of projects; and effective partnerships among agencies, utilities, the private sector, and states. Partnerships lead to increased motivation and education and reduced barriers to successful procurement. As the lead organization implementing legislation and Presidential direction for Federal energy efficiency, FEMP administers an interagency energy committee and task force and collaborates with the DOE national energy laboratories. FEMP works with energy service companies, energy savings product manufacturers, and utilities. This partnership will lead to a $1 billion investment by companies willing to invest in return for a share of the energy cost savings. With FEMP project financing, audits, training and technical assistance, and new technology demonstrations, agencies overcome obstacles to achieving widespread energy efficiency.

  16. FEMP/NTDP Technology Focus Chiller Controls-related Energy Saving Opportunities

    E-Print Network [OSTI]

    FEMP/NTDP Technology Focus Chiller Controls-related Energy Saving Opportunities in Federal.S. Department of Energy under Contract No. DE-AC03-76SF00098. 1 INTRODUCTION Chillers are a significant in recent years has been on optimization of set point and staging controls, improvements in chiller design

  17. FEMP/NTDP Technology Focus New Technology

    E-Print Network [OSTI]

    FEMP/NTDP Technology Focus New Technology Demonstration Program Technology Focus FEMPFederal Energy Management Program Trends in Energy Management Technology: BCS Integration Technologies ­ Open Communications into a complete EMCIS. The first article [1] covered enabling technologies for emerging energy management systems

  18. 2008 Federal Energy Management Program (FEMP) Market Report

    SciTech Connect (OSTI)

    Tremper, C.

    2009-07-01T23:59:59.000Z

    This report assesses the market for Federal Energy Management Program (FEMP) services as it existed in FY 2008. It discusses Federal energy management goal progress in FY 2008, and examines the environment in which agencies implemented energy management projects over the last three years. The report also discusses some recent events that will increase the market for FEMP services, and outlines FEMP's major strategies to address these changes in FY 2009 and beyond.

  19. Lead by Example with Smart Energy Management FEMP (Revised Brochure)

    SciTech Connect (OSTI)

    Not Available

    2008-07-01T23:59:59.000Z

    This brochure provides the primary audience of Federal facility and energy managers with an accurate understanding of the services and assistance available through FEMP.

  20. FEMP Offers Updated Training on the Guiding Principles for High...

    Broader source: Energy.gov (indexed) [DOE]

    Energy's Federal Energy Management Program (FEMP) presents an updated series of training courses focused on the Guiding Principles for Federal Leadership in High-Performance and...

  1. FEMP Outdoor Solid-State Lighting Intiative: Resources for Outdoor...

    Broader source: Energy.gov (indexed) [DOE]

    sheet describes the Federal Energy Management Program's (FEMP) solid-state lighting (SSL) initiatives that provide information and resources for the application of SSL lighting...

  2. FEMP Technical Assistance to U.S. NORTHCOM (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-01-01T23:59:59.000Z

    Fact sheet overview of FEMP technical assistance services provided to the U.S. NORTHCOM as part of the American Recovery and Reinvestment Act.

  3. FEMP UESC Overview | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFICPracticesFEMP UESC

  4. Progress report on decommissioning activities at the Fernald Environmental Management Project (FEMP) site

    SciTech Connect (OSTI)

    NONE

    1998-07-01T23:59:59.000Z

    The Fernald Environmental Management Project (FEMP), is located about 18 miles northwest of Cincinnati, Ohio. Between 1953 and 1989, the facility, then called the Feed Material Production Center or FMPC, produced uranium metal products used in the eventual production of weapons grade material for use by other US Department of Energy (DOE) sites. In 1989, FMPC`s production was suspended by the federal government in order to focus resources on environmental restoration versus defense production. In 1992, Fluor Daniel Fernald assumed responsibility for managing all cleanup activities at the FEMP under contract to the DOE. In 1990, as part of the remediation effort, the site was divided into five operable units based on physical proximity of contaminated areas, similar amounts of types of contamination, or the potential for a similar technology to be used in cleanup activities. This report continues the outline of the decontamination and decommissioning (D and D) activities at the FEMP site Operable Unit 3 (OU3) and provides an update on the status of the decommissioning activities. OU3, the Facilities Closure and Demolition Project, involves the remediation of more than 200 uranium processing facilities. The mission of the project is to remove nuclear materials stored in these buildings, then perform the clean out of the buildings and equipment, and decontaminate and dismantle the facilities.

  5. MSENGR Product Design Program Proposal

    E-Print Network [OSTI]

    Prinz, Friedrich B.

    MSENGR Product Design Program Proposal Rev 6/2007 p. 1 New Proposal Revision First graduate Language 3 ME216A Advanced Product Design: Need Finding 4 ME312 Advanced Product Design: Form Giving 4 ARTSTUDI160 Design II: The Bridge 3 ME216B Advanced Product Design: Implementation 4 ME316

  6. FEMP Peer Review | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKETPlanning toPeer Review FEMP

  7. FEMP Peer Review | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 FederalTexasManager FAQS Reference Guide| Department ofPracticesPanelFEMP

  8. Overview of the ESCO Selection Process and FEMP ESPC Templates

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1 Overview of the ESCO Selection Process and FEMP ESPC Templates A high-level overview of the steps towards ESCO selection is depicted in the figure below. The corresponding ESPC...

  9. FEMP Offers New Training on Photovoltaic Operations and Maintenance...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The instructors for this seminar are Brad Gustafson, P.E., CEM, LEED AP, supervisor of customer services for DOE FEMP, and Andy Walker, P.E., Ph.D., principal engineer at the...

  10. Federal Utility Partnership Working Group Seminar: DOE/FEMP...

    Office of Environmental Management (EM)

    May 7, 2014 David McAndrew Utility Project Lead DOE FEMP 2 Welcome To Virginia Beach Thank you to Virginia Natural Gas and AGL Resources for hosting the 2014 Spring FUPWG...

  11. Covered Product Category: Compact Fluorescent Lamps

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including compact fluorescent lamps (CFLs), which are an ENERGY STAR-qualified product category.

  12. Covered Product Category: Commercial Fryers

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial fryers, which is a product category covered by the ENERGY STAR program.

  13. Covered Product Category: Commercial Griddles

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial griddles, which is a product category covered by the ENERGY STAR program

  14. FEMP and U.S. Army Corps of Engineers Partner to Drive Down Federal...

    Office of Environmental Management (EM)

    FEMP and U.S. Army Corps of Engineers Partner to Drive Down Federal Energy Costs FEMP and U.S. Army Corps of Engineers Partner to Drive Down Federal Energy Costs March 26, 2015 -...

  15. An integrated teamwork approach to regional FEMP project implementation

    SciTech Connect (OSTI)

    Jhaveri, A.

    1996-05-01T23:59:59.000Z

    With the establishment of Regional Energy Action Project (REAP) teams in Seattle, Chicago, and New York earlier this year, the U.S. Department of Energy`s Federal Energy Management Program (FEMP) has taken a quantum leap towards assisting Federal agencies meet the minimum 30% energy savings goal, through the year 2005 from the baseline year of 1985, per the Executive Order No. 12902. The three (3) member team, including the FEMP liaison, at these three (3) Support Offices, has significantly increased the manpower resources and expertise needed to implement FEMP projects through technical, financial, marketing, procurement, and contracting assistance in each region, thus complementing the limited resources of the participating Federal agencies. The potential and opportunities available in the four-state Region 10 (Washington, Oregon, Idaho, Alaska) for aggressively promoting FEMP projects are significant as demonstrated by some 20 completed SAVEnergy Action Plan Audits and as many as 10 energy efficiency projects with innovative financing arrangements, including but not limited to, agency appropriations, utility Demand Side Management (DSM), Energy Savings Performance Contract (ESPC) and third party financing handled by Energy Service Companies (ESCO`s), and/or combinations of these. This presentation will highlight some of the specific FEMP projects including partnership development, negotiations, coordination, and technical support models used to assist the selected Federal agency.

  16. Covered Product Category: Residential Central Air Conditioners...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Central Air Conditioners Covered Product Category: Residential Central Air Conditioners The Federal Energy Management Program (FEMP) provides acquisition guidance for residential...

  17. Covered Product Category: Residential Electric Resistance Water...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Electric Resistance Water Heaters Covered Product Category: Residential Electric Resistance Water Heaters The Federal Energy Management Program (FEMP) sets federal efficiency...

  18. Covered Product Category: Residential Gas Storage Water Heaters...

    Energy Savers [EERE]

    Gas Storage Water Heaters Covered Product Category: Residential Gas Storage Water Heaters The Federal Energy Management Program (FEMP) provides acquisition guidance for gas storage...

  19. Covered Product Category: Water-Cooled Electric Chillers | Department...

    Energy Savers [EERE]

    Water-Cooled Electric Chillers Covered Product Category: Water-Cooled Electric Chillers The Federal Energy Management Program (FEMP) provides acquisition guidance and Federal...

  20. Covered Product Category: Residential Whole-Home Gas Tankless...

    Energy Savers [EERE]

    Whole-Home Gas Tankless Water Heaters Covered Product Category: Residential Whole-Home Gas Tankless Water Heaters The Federal Energy Management Program (FEMP) provides acquisition...

  1. Covered Product Category: Residential Air-Source Heat Pumps

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for residential air-source heat pumps, which is an ENERGY STAR-qualified product category.

  2. Covered Product Category: Residential Heat Pump Water Heaters...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Heat Pump Water Heaters Covered Product Category: Residential Heat Pump Water Heaters The Federal Energy Management Program (FEMP) provides acquisition guidance and Federal...

  3. Covered Product Category: Residential Electric Resistance Water Heaters

    Broader source: Energy.gov [DOE]

    FEMP sets federal efficiency requirements and provides acquisition guidance across a variety of product categories, including residential electric resistance water heaters.

  4. U.S. Army Corps of Engineers and FEMP Partner to Drive Down Federal...

    Broader source: Energy.gov (indexed) [DOE]

    have been executing energy savings performance contract (ESPC) and utility energy service contract (UESC) projects for several years. FEMP has had programmatic responsibility for...

  5. Federal Fleet Files, FEMP, Vol. 2, No. 11 - October 2010 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-10-01T23:59:59.000Z

    October 2010 update from the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  6. Federal Fleet Files, FEMP, Vol. 1, No. 4 - September 2009 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-09-01T23:59:59.000Z

    September 2009 issue of the monthly newsletter for the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  7. Federal Fleet Files, FEMP, Vol. 2, No. 12 - November 2010 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-11-01T23:59:59.000Z

    November 2010 update from the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  8. Federal Fleet Files, FEMP, Vol. 2, No. 8 - June 2010 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-06-01T23:59:59.000Z

    June 2010 update from the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  9. Federal Fleet Files, FEMP, Vol. 2, No. 7 - May 2010 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-05-01T23:59:59.000Z

    May 2010 update from the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  10. Federal Fleet Files, FEMP, Vol. 2, No. 4 - January 2010 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-01-01T23:59:59.000Z

    January 2010 update from the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  11. Federal Fleet Files, FEMP, Vol. 1, No. 3 - July 2009 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-07-01T23:59:59.000Z

    July 2009 issue of the monthly newsletter for the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  12. Federal Fleet Files, FEMP, Vol. 1, No. 1 - May 2009 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-05-01T23:59:59.000Z

    Monthly newsletter for the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  13. Federal Fleet Files, FEMP, Vol. 2, No. 2 - November 2009 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-11-01T23:59:59.000Z

    November 2009 issue of monthly news from the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  14. Federal Fleet Files, FEMP, Vol. 2, No. 10 - September 2010 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-09-01T23:59:59.000Z

    September 2010 update from the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  15. Federal Fleet Files, FEMP, Vol. 2, No. 13 - December 2010 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-12-01T23:59:59.000Z

    December 2010 update from the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to federal agencies.

  16. Federal Fleet Files, FEMP, Vol. 2, No. 9 - July 2010 (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-07-01T23:59:59.000Z

    July 2010 update from the FEMP Federal Fleet Program that outlines vehicle, alternative fuel, infrastructure, and management strategy updates to Federal agencies.

  17. SP.778 Toy Product Design, Spring 2007

    E-Print Network [OSTI]

    Kudrowitz, Barry M. (Barry Matthew)

    Toy Product Design is a MIT Public Service Center learning design course offered in the Spring semester. This course is an introduction to the product design process with a focus on designing for play and entertainment. ...

  18. FEMP Update: Federal Energy Management activities, July 1985

    SciTech Connect (OSTI)

    Not Available

    1985-01-01T23:59:59.000Z

    Since early 1984, FEMP has examined a number of innovative techniques for financing energy efficiency improvements in Federal facilities. Having identified a number of legal and procurement barriers to shared savings contracting by Federal agencies, FEMP set out to identify and explore possible solutions. Currently, it has narrowed in on three specific options which represent potentially viable approaches to Federal energy financing: (1) removing regulatory and institutional barriers to energy services contracts with the private sector; (2) implementing energy services agreements at Government Owned Contractor Operated (GOCO) facilities; and (3) establishing a government financial corporation to fund agency energy conservation investments. These possible solutions are discussed in the report. The third possibility is regarded as unlikely.

  19. What`s new in federal energy management: FEMP program overview. Federal energy saver showcases

    SciTech Connect (OSTI)

    NONE

    1996-08-01T23:59:59.000Z

    To promote widespread Federal energy efficiency, agencies are showcasing their best energy efficiency, water conserving, and solar and other renewable energy technologies. To highlight these successful energy-efficient projects, Executive Order 12902 directs agencies to designate at least one newly constructed or existing building as a showcase facility. At existing facilities, agencies must also try to incorporate cogeneration and indoor air quality improvements. Agencies are directed to develop and implement effective plans to make these showcase projects happen. Project successes will show the strength of partnering with other agencies, energy services companies, utilities, and national laboratories, and of using the US Department of Energy Federal Energy Management Program (FEMP) as a resource. The goal is Federal facilities operating at peak efficiency. A Federal Energy Saver Showcase plaque is prominently displayed at each showcase site, notifying visitors they are entering a government building that successfully conserves energy and water and saves taxpayer dollars.

  20. Production design for plate products in the steel industry

    E-Print Network [OSTI]

    We describe an optimization tool for a multistage production process for ... plates. The problem we solve yields a production design (or plan) for rectangular plate.

  1. FEMP Launches New Training Search Tool | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN8.EnergyFEMP

  2. American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance for Geothermal Resource Evaluation Projects

    SciTech Connect (OSTI)

    Robert P. Breckenridge; Thomas R. Wood; Joel Renner

    2010-09-01T23:59:59.000Z

    The purpose of this document is to report on the evaluation of geothermal resource potential on and around three different United States (U. S.) Air Force Bases (AFBs): Nellis AFB and Air Force Range (AFR) in the State of Nevada (see maps 1 and 5), Holloman AFB in the State of New Mexico (see map 2), and Mountain Home AFB in the State of Idaho (see map 3). All three sites are located in semi-arid parts of the western U. S. The U. S. Air Force, through its Air Combat Command (ACC) located at Langley AFB in the State of Virginia, asked the Federal Energy Management Program (FEMP) for technical assistance to conduct technical and feasibility evaluations for the potential to identify viable geothermal resources on or around three different AFBs. Idaho National Laboratory (INL) is supporting FEMP in providing technical assistance to a number of different Federal Agencies. For this report, the three different AFBs are considered one project because they all deal with potential geothermal resource evaluations. The three AFBs will be evaluated primarily for their opportunity to develop a geothermal resource of high enough quality grade (i.e., temperature, productivity, depth, etc.) to consider the possibility for generation of electricity through a power plant. Secondarily, if the resource for the three AFBs is found to be not sufficient enough for electricity generation, then they will be described in enough detail to allow the base energy managers to evaluate if the resource is suitable for direct heating or cooling. Site visits and meetings by INL personnel with the staff at each AFB were held in late FY-2009 and FY-2010. This report provides a technical evaluation of the opportunities and challenges for developing geothermal resources on and around the AFBs. An extensive amount of literature and geographic information was evaluated as a part of this assessment. Resource potential maps were developed for each of the AFBs.

  3. FEMP Presents Its Newest On-Demand eTraining Course on Building...

    Energy Savers [EERE]

    On-Demand eTraining Course on Building Automation Systems FEMP Presents Its Newest On-Demand eTraining Course on Building Automation Systems November 19, 2013 - 12:00am Addthis...

  4. FEMP Offers Training on Federal On-Site Renewable Power Purchase...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Training on Federal On-Site Renewable Power Purchase Agreements FEMP Offers Training on Federal On-Site Renewable Power Purchase Agreements March 30, 2015 - 2:16pm Addthis The U.S....

  5. Data mining in design of products and production systems

    E-Print Network [OSTI]

    Kusiak, Andrew

    Data mining in design of products and production systems Andrew Kusiak *, Matthew Smith Intelligent Data mining is acquiring its own identity by refining concepts from other disciplines, developing affected by the data mining pursuit. This paper outlines areas of product and manufacturing system design

  6. Covered Product Category: Light Fixtures (Luminaires)

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including luminaires, or light fixtures. The luminaires product category is very broad and covers a wide variety of lighting products. Both ENERGY STAR® and FEMP provide programmatic guidance for various types of luminaires. See table 2 for more information about which types of light fixtures are covered by which program (FEMP or ENERGY STAR). Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  7. Design of product development systems

    E-Print Network [OSTI]

    Aguirre Granados, Adrian

    2008-01-01T23:59:59.000Z

    The development of successful new products in less time and using fewer resources is key to the financial success of most consumer product companies. In this thesis we have studied the development of new products and how ...

  8. Teaching Design for Environment in Product Design Classes

    E-Print Network [OSTI]

    Baeriswyl, Michael C.

    The paper presents an approach to teaching design for environment (DFE) in the context of a product design and development course. The teaching method has been applied in our classes for graduate engineering, business, and ...

  9. SP.778 Toy Product Design, Spring 2006

    E-Print Network [OSTI]

    Kudrowitz, Barry

    This course is an introduction to the product design process with an emphasis on designing for children and entertainment. Students will work in small teams to develop a working prototype of a toy. Throughout the semester ...

  10. Guide to FEMP-Designated Parking Lot Lighting

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet), GeothermalGrid Integration0-1 March 2013 WHAT: The last7 Guide9TABLE

  11. Guide to FEMP-Designated Parking Structure Lighting

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet), GeothermalGrid Integration0-1 March 2013 WHAT: The last7

  12. FEMP Releases 10 Updated Covered Product Categories | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKETPlanning toPeerReleases 10

  13. Universal Product Design: Transforming User Activity Into Product Function

    E-Print Network [OSTI]

    Kostovich, Vincent

    2010-07-14T23:59:59.000Z

    Many people have disabilities and would like to have all of the amenities typical of daily life. Universal product design is important in designing for the disabled and creating user-friendly products for all people. The goal of this thesis...

  14. EPA's designated products in eight categories: Construction Products

    E-Print Network [OSTI]

    folders, clip portfolios, and presentation folders Office furniture Office recycling containers Office tires Miscellaneous Products Awards and plaques Bike racks Blasting grit Industrial drums Manual" program and Comprehensive Procurement Guideline (CPG), designates items that MUST contain recycled

  15. Multi-Period Production Capacity Planning for Integrated Product and Production System Design*

    E-Print Network [OSTI]

    Saitou, Kazuhiro "Kazu"

    Multi-Period Production Capacity Planning for Integrated Product and Production System Design* Emre.ac.uk kazu@umich.edu .Abstract ­ This paper presents a simulation-based method to aid multi-period production capacity planning by quantifying the trade-off between product quality and production cost. The product

  16. Covered Product Category: Cool Roof Products

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including cool roof products, which are an ENERGY STAR®-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  17. CIRP Design Conference 2011 Product Lifecycle Management Model for Design Information Management in

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    CIRP Design Conference 2011 Product Lifecycle Management Model for Design Information Management Product Lifecycle Management (PLM) is one way to improve productivity in all manufacturing companies. Keywords: Product Lifecycle Management, Product Process Organisation Model, Unified Modelling Language 1

  18. Subscribe to Energy-Efficient Product Procurement Updates

    Broader source: Energy.gov [DOE]

    FEMP offers e-mail updates covering energy-efficient product procurement requirements, guidance, and assistance. Enter your e-mail address below to begin the registration process. After you...

  19. Design Case Summary: Production of Gasoline and Diesel from Biomass...

    Energy Savers [EERE]

    Design Case Summary: Production of Gasoline and Diesel from Biomass via Fast Pyrolysis, Hydrotreating, and Hydrocracking Design Case Summary: Production of Gasoline and Diesel from...

  20. FEMP Webcast: O&M Best Practices for Small-Scale PV Systems

    Broader source: Energy.gov [DOE]

    Hosted by the Federal Energy Management Program (FEMP), this seminar covers operations and maintenance (O&M) best practices for photovoltaic (PV) systems of 100 kilowatt or less, including planning for a PV O&M scope of work and maintenance procedures to keep the system operating at optimal capacity.

  1. FEMP fiscal year 1999 ESPC business strategy development summary report[Energy Saving Performance Contract

    SciTech Connect (OSTI)

    KL McMordie-Stoughton; WDM Hunt

    2000-05-04T23:59:59.000Z

    The mission of the US Department of Energy's Federal Energy Management Program (FEMP) is to reduce the cost of Government by advancing energy efficiency, water conservation, and the use of solar and other renewable technologies. This is accomplished by creating partnerships, leveraging resources, transferring technology, and providing training and technical guidance and assistance to agencies. Each of these activities is directly related to achieving requirements set forth in the Energy Policy Act of 1992 and the goals that have been established in Executive Order 13123 (June 1999), but also those that are inherent in sound management of Federal financial and personnel resources. The Pacific Northwest National Laboratory (PNNL) supports the FEMP mission in all activity areas. This responsibility includes working with various Federal energy managers to identify, monitor, and evaluate the performance of new energy efficiency technologies suitable for installation at Federal sites. This report provides the results of a Energy Saving Performance Contracting (ESPC) Business Strategy Development project that PNNL conducted for FEMP. The project provides information regarding the development of Federal market scenarios for FEMP Super-ESPC delivery orders. Two market scenarios were developed. The initial scenario resulted in an estimated delivery order target that was much lower than initially estimated in the spring of 1998. The second scenario yielded a lower estimated number of delivery orders. The main difference between these two scenarios was an estimated increase in utility financed projects in the Federal sector.

  2. PLUTONIUM-238 PRODUCTION TARGET DESIGN STUDIES

    SciTech Connect (OSTI)

    Hurt, Christopher J [ORNL; Wham, Robert M [ORNL; Hobbs, Randall W [ORNL; Owens, R Steven [ORNL; Chandler, David [ORNL; Freels, James D [ORNL; Maldonado, G Ivan [ORNL

    2014-01-01T23:59:59.000Z

    A new supply chain is planned for plutonium-238 using existing reactors at the Oak Ridge National Laboratory (ORNL) and Idaho National Laboratory (INL) and existing chemical recovery facilities at ORNL. Validation and testing activities for new irradiation target designs have been conducted in three phases over a 2 year period to provide data for scale-up to production. Target design, qualification, target fabrication, and irradiation of fully-loaded targets have been accomplished. Data from post-irradiation examination (PIE) supports safety analysis and irradiation of future target designs.

  3. Product Design for Energy: An Inverted Pyramid Approach

    E-Print Network [OSTI]

    Gopalakrishnan, B.; Alkadi, N. M.; Plummer, R. W.

    The product design function is important within the spectrum of the product life cycle. Manufacturing processes are likely to consume much energy, as evidenced in aluminum and steel industries. The product design parameters such as the material...

  4. Huntington Veterans Affairs Medical Center - Faucet and Showerhead Replacement Project: Best Management Practice Case Study #7: Faucets and Showerheads, Federal Energy Management Program (FEMP) (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2009-12-01T23:59:59.000Z

    Case study overview of the Huntington Veterans Affairs Medical Center water efficiency program as part of FEMP's water efficiency best management practice series.

  5. Fort Huachuca Water Awareness Program: Best Management Practice Case Study #2: Information and Education Programs, Federal Energy Management Program (FEMP) (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2009-12-01T23:59:59.000Z

    Case study overview of the U.S. Army Fort Huachuca water awareness practice as part of FEMP's water efficiency best management practice series.

  6. MOLTEN CARBONATE FUEL CELL PRODUCT DESIGN IMPROVEMENT

    SciTech Connect (OSTI)

    H.C. Maru; M. Farooque

    2005-03-01T23:59:59.000Z

    The program was designed to advance the carbonate fuel cell technology from full-size proof-of-concept field test to the commercial design. DOE has been funding Direct FuelCell{reg_sign} (DFC{reg_sign}) development at FuelCell Energy, Inc. (FCE, formerly Energy Research Corporation) from an early state of development for stationary power plant applications. The current program efforts were focused on technology and system development, and cost reduction, leading to commercial design development and prototype system field trials. FCE, in Danbury, CT, is a world-recognized leader for the development and commercialization of high efficiency fuel cells that can generate clean electricity at power stations, or at distributed locations near the customers such as hospitals, schools, universities, hotels and other commercial and industrial applications. FCE has designed three different fuel cell power plant models (DFC300A, DFC1500 and DFC3000). FCE's power plants are based on its patented DFC{reg_sign} technology, where a hydrocarbon fuel is directly fed to the fuel cell and hydrogen is generated internally. These power plants offer significant advantages compared to the existing power generation technologies--higher fuel efficiency, significantly lower emissions, quieter operation, flexible siting and permitting requirements, scalability and potentially lower operating costs. Also, the exhaust heat by-product can be used for cogeneration applications such as high-pressure steam, district heating and air conditioning. Several sub-MW power plants based on the DFC design are currently operating in Europe, Japan and the US. Several one-megawatt power plant design was verified by operation on natural gas at FCE. This plant is currently installed at a customer site in King County, WA under another US government program and is currently in operation. Because hydrogen is generated directly within the fuel cell module from readily available fuels such as natural gas and waste water treatment gas, DFC power plants are ready today and do not require the creation of a hydrogen infrastructure. Product improvement progress made during the program period in the areas of technology, manufacturing processes, cost reduction and balance-of-plant equipment designs is discussed in this report.

  7. Experience with the Architectural Design of a Modest Product Family

    E-Print Network [OSTI]

    Lutz, Robyn R.

    1 Experience with the Architectural Design of a Modest Product Family Robert W. Schwanke Siemens Laboratory rlutz@cs.iastate.edu #12;2 Summary Many product families are modest in the sense that they consist for the architectural design of a modest product family. The paper describes the process, design alternatives

  8. Covered Product Category: Displays

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including displays, which are covered by the ENERGY STAR program. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  9. Design and Production Interface in Lean Production: A Performance Improvement Criteria Proposition Proceedings IGLC `98

    E-Print Network [OSTI]

    Tommelein, Iris D.

    Design and Production Interface in Lean Production: A Performance Improvement Criteria Proposition Proceedings IGLC `98 DESIGN AND PRODUCTION INTERFACE IN LEAN PRODUCTION: A PERFORMANCE IMPROVEMENT CRITERIA PROPOSITION Eduardo L. Isatto1 and Carlos T. Formoso2 ABSTRACT Failures on transferring Japanese production

  10. FEMP and Department of Transportation Partnership Wins GreenGov...

    Broader source: Energy.gov (indexed) [DOE]

    technologies and techniques to assist the Department in designing one of the first energy- and water-efficient airport control towers that meet the high-performance...

  11. FEMP Helps Federal Facilities Develop Large-Scale Renewable Energy Projects

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 FederalTexasManager FAQS Reference Guide| Department of Energy FEMP

  12. Meeting with EarthJustice Regarding FEMP Rulemakings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking ofOil & GasTechnicalMeeting with EarthJustice Regarding FEMP Rulemakings

  13. FEMP Best Practices and Lessons Learned for Federal Agency ESPC Projects

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN CameronFEMP Best

  14. FEMP Best Practices and Lessons Learned for Federal Agency ESPC Projects: Acquisition Planning

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN CameronFEMP Best3.

  15. FEMP Best Practices and Lessons Learned for Federal Agency ESPC Projects: Critical Outcomes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN CameronFEMP

  16. FEMP Best Practices and Lessons Learned for Federal Agency ESPC Projects: ESCO Selection

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN CameronFEMP4. ESCO

  17. FEMP Best Practices and Lessons Learned for Federal Agency ESPC Projects: Final Negotiations

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN CameronFEMP4. ESCO.

  18. FEMP Best Practices and Lessons Learned for Federal Agency ESPC Projects: General Best Practices

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN CameronFEMP4.

  19. FEMP Best Practices and Lessons Learned for Federal Agency ESPC Projects: Introduction

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN CameronFEMP4..

  20. FEMP Best Practices and Lessons Learned for Federal Agency ESPC Projects: Investment-Grade Audit

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN CameronFEMP4..7.

  1. FEMP Best Practices and Lessons Learned for Federal Agency ESPC Projects: Measurement and Verification

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN CameronFEMP4..7.1.

  2. arra femp technical: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    is published Erdem, Erkut 29 Technical Brief CiteSeer Summary: ii iiiFOREWARD The Depleted Uranium Technical Brief is designed to convey available information and knowledge about...

  3. Case study in rapid product design and development

    E-Print Network [OSTI]

    Winther, Garrett L. (Garrett Lee)

    2011-01-01T23:59:59.000Z

    This thesis explores a new strategy in developing products quickly, cheaply and efficiently, with the hopes to redefine the paradigms behind the product design process. This was carried out through the development of the ...

  4. An innovative concept for deep water oil production platform design 

    E-Print Network [OSTI]

    Racine, Florian

    1994-01-01T23:59:59.000Z

    As more oil and gas are discovered in deep water, the offshore industry has become increasingly interested in the design of deep water offshore production facilities. A new design concept tentatively called FPSOT (Floating ...

  5. Characteristics of successful risk management in product design

    E-Print Network [OSTI]

    Olechowski, Alison Louise

    The paper reports results of one of the largest empirical studies to-date on the impact of design risk management practices on product design success. Through a survey of 224 practices, 38 (in 7 categories) where found to ...

  6. Qualities That Define a Well-Designed Product

    E-Print Network [OSTI]

    Pirics, Marjorie

    2011-08-08T23:59:59.000Z

    The primary objective of this research is to identify the defining characteristics of “good design” as applied to Industrial Design and to determine what specific qualities it possesses. I assessed what qualities in a product serve as attractors...

  7. New product development methods : a study of open design

    E-Print Network [OSTI]

    Smith, Ariadne G. (Ariadne Geneviève)

    2012-01-01T23:59:59.000Z

    This thesis explores the application of open design to the process of developing physical products. Open design is a type of decentralized innovation that is derived from applying principles of open source software and ...

  8. Design Case Summary: Production of Mixed Alcohols from Municipal...

    Office of Environmental Management (EM)

    Mixed Alcohols from Municipal Solid Waste via Gasification Design Case Summary: Production of Mixed Alcohols from Municipal Solid Waste via Gasification The Bioenergy Technologies...

  9. Plant Design for the Production of DUAGG

    SciTech Connect (OSTI)

    Ferrada, J.J.

    2003-02-04T23:59:59.000Z

    The cost of producing DUAGG is an important consideration for any interested private firm in determining whether DUCRETE is economically viable as a material of construction in next-generation spent nuclear fuel casks. This study analyzed this project as if it was a stand-alone project. The capital cost includes engineering design, equipment costs and installation, start up, and management; the study is not intended to be a life-cycle cost analysis. The costs estimated by this study are shown in Table ES.1, and the conclusions of this study are listed in Table ES.2. The development of DUAGG and DUCRETE is a major thrust of the Depleted Uranium Uses Research and Development Project. An obvious use of depleted uranium is as a shielding material (e.g., DUCRETE). DUCRETE is made by replacing the conventional stone aggregate in concrete with DUAGG. One objective of this project is to bring the development of DUCRETE to a point at which a demonstrated basis exists for its commercial deployment. The estimation of the costs to manufacture DUAGG is an important part of this effort. Paul Lessing and William Quapp developed DUAGG and DUCRETE as part of an Idaho National Engineering and Environmental Laboratory (INEEL) program to find beneficial uses for depleted uranium (DU). Subsequently, this technology was licensed to Teton Technologies, Inc. The DUAGG process mixes DUO{sub 2} with sintering materials and additives to form pressed briquettes. These briquettes are sintered at 1300 C, and the very dense sintered briquettes are then crushed and classified into gap-graded size fractions. The graded DUAGG is then ready to be used to make high-strength heavy DUCRETE. The DUCRETE shielding will be placed into an annular steel cask-shell mold, which has internal steel reinforcing bars. The objectives of this study are to (1) use previous DUAGG process developments to design a plant that will produce DUAGG at a baseline rate, (2) determine the size of the equipment required to meet the DUAGG production scale, (3) estimate the facility's capital and operating costs, and (4) perform a parametric sensitivity analysis on those elements of cost that most affect the total operating expenses. Because the study does not include preoperational, decontamination, decommissioning, and closure costs, it cannot be considered a complete life-cycle cost analysis. However, the purpose of this analysis is to establish the potential viability of the DUAGG process as a private commercial venture to meet a market demand for advanced spent nuclear fuel (SNF) storage and transport casks.

  10. Designer proton-channel transgenic algae for photobiological hydrogen production

    DOE Patents [OSTI]

    Lee, James Weifu (Knoxville, TN)

    2011-04-26T23:59:59.000Z

    A designer proton-channel transgenic alga for photobiological hydrogen production that is specifically designed for production of molecular hydrogen (H.sub.2) through photosynthetic water splitting. The designer transgenic alga includes proton-conductive channels that are expressed to produce such uncoupler proteins in an amount sufficient to increase the algal H.sub.2 productivity. In one embodiment the designer proton-channel transgene is a nucleic acid construct (300) including a PCR forward primer (302), an externally inducible promoter (304), a transit targeting sequence (306), a designer proton-channel encoding sequence (308), a transcription and translation terminator (310), and a PCR reverse primer (312). In various embodiments, the designer proton-channel transgenic algae are used with a gas-separation system (500) and a gas-products-separation and utilization system (600) for photobiological H.sub.2 production.

  11. Pilot study risk assessment for selected problems at the Fernald Environmental Management Project (FEMP)

    SciTech Connect (OSTI)

    Hamilton, L.D.; Meinhold, A.F.; Baxter, S.L.; Holtzman, S.; Morris, S.C.; Pardi, R.; Rowe, M.D.; Sun, C. [Brookhaven National Lab., Upton, NY (United States); Anspaugh, L.; Layton, D. [Lawrence Livermore National Lab., CA (United States)

    1993-03-01T23:59:59.000Z

    Two important environmental problems at the USDOE Fernald Environmental Management Project (FEMP) facility in Fernald, Ohio were studied in this human health risk assessment. The problems studied were radon emissions from the K-65 waste silos, and offsite contamination of ground water with uranium. Waste from the processing of pitchblende ore is stored in the K-65 silos at the FEMP. Radium-226 in the waste decays to radon gas which escapes to the outside atmosphere. The concern is for an increase in lung cancer risk for nearby residents associated with radon exposure. Monitoring data and a gaussian plume transport model were used to develop a source term and predict exposure and risk to fenceline residents, residents within 1 and 5 miles of the silos, and residents of Hamilton and Cincinnati, Ohio. Two release scenarios were studied: the routine release of radon from the silos and an accidental loss of one silo dome integrity. Exposure parameters and risk factors were described as distributions. Risks associated with natural background radon concentrations were also estimated.

  12. Covered Product Category: Imaging Equipment

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including imaging equipment, which is covered by the ENERGY STAR® program. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  13. Covered Product Category: Fluorescent Luminaires

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including fluorescent luminaires. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  14. Production design for plate products in the steel industry

    E-Print Network [OSTI]

    Sanjeeb Dash

    2007-04-05T23:59:59.000Z

    Apr 5, 2007 ... Abstract: We describe an optimization tool for a multistage production process for rectangular steel plates. The problem we solve yields a ...

  15. COSTS MODELS IN DESIGN AND MANUFACTURING OF SAND CASTING PRODUCTS

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    COSTS MODELS IN DESIGN AND MANUFACTURING OF SAND CASTING PRODUCTS Nicolas PERRY Ass. Prof., IRCCy.Bernard@irccyn.ec-nantes.fr Abstract: In the early phases of the product life cycle, the costs controls became a major decision tool difficulties, we will present an approach using a concept of cost entity related to the design and realization

  16. ENES 100 Introduction to Engineering Design Hovercraft Product Specifications

    E-Print Network [OSTI]

    Jacob, Bruce

    requirements (a) The use of internal combustion engines (gas and glow fuel engines) is prohibited. (bENES 100 Introduction to Engineering Design Hovercraft Product Specifications HC_PS_005 Rev. A, 28 to Engineering Design Hovercraft Product Specifications HC_PS_005 Rev. A, 28 August 2008 Figure 1: The test

  17. ENES 100 Introduction to Engineering Design Hovercraft Product Specifications

    E-Print Network [OSTI]

    Jacob, Bruce

    requirements (a) The use of internal combustion engines (gas and glow fuel engines) is prohibited. (bENES 100 Introduction to Engineering Design Hovercraft Product Specifications HC_PS_004 Rev. A, 22 100 Introduction to Engineering Design Hovercraft Product Specifications HC_PS_004 Rev. A, 22 January

  18. School of Architecture, Design and the Built Environment Sustainable Product Design

    E-Print Network [OSTI]

    Evans, Paul

    of product lifecycle. To meet such a demand, this research is to develop a novel approach for sustainable, but the approach developed will also be useful for other type of products. A lifecycle design will be applied, i.e., the design constrains will cover all stages of the whole lifecycle of the product, such as extraction

  19. Covered Product Category: Residential Central Air Conditioners

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including residential central air conditioners (CACs), which are an ENERGY STAR®-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  20. Covered Product Category: Room Air Conditioners

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including room air conditioners, which are an ENERGY STAR®-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  1. Covered Product Category: Residential Gas Furnaces

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including residential gas furnaces, which are an ENERGY STAR®-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  2. Covered Product Category: Residential Geothermal Heat Pumps

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including geothermal heat pumps, which are an ENERGY STAR®-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  3. American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance

    SciTech Connect (OSTI)

    Robert P. Breckenridge; Thomas R. Wood

    2010-08-01T23:59:59.000Z

    The purpose of this document is to evaluate the opportunity for Letterkenny Army Depot (LEAD or the Depot) to utilize biogenic methane, which may be available in shale formations under the Depot, to provide a supplemental source of natural gas that could allow the Depot to increase energy independence. Both the Director and Deputy of Public Works at the Depot are supportive in general of a methane production project, but wanted to better understand the challenges prior to embarking on such a project. This report will cover many of these issues. A similar project has been successfully developed by the U. S. Army at Ft. Knox, KY, which will be explained and referred to throughout this report as a backdrop to discussing the challenges and opportunities at LEAD, because the geologic formations and possibilities at both sites are similar. Prior to discussing the opportunity at LEAD, it is important to briefly discuss the successful methane recovery operation at Ft. Knox, because it is applicable to the projected approach for the LEAD methane system. The Ft. Knox project is an excellent example of how the U. S. Army can use an onsite renewable resource to provide a secure energy source that is not dependent on regional energy networks and foreign oil. At Ft. Knox, the U. S. Army contracted (through a utility co-op) with an energy production company to drill wells, establish a distribution infrastructure, and provide the equipment needed to prepare and compress the produced methane gas for use by base operations. The energy production company agreed to conduct the exploratory investigation at Ft. Knox with no cost to the government, as long as they could be granted a long-term contract if a reliable energy resource was established. The Depot is located, in part, over an Ordovician Age shale formation that may have the potential for producing biogenic methane, similar to the Devonian Age shale found beneath Ft. Knox. However, the Ordovician Age Shale beneath the Letterkenny Depot is not known to have any currently producing gas wells.

  4. The Product Oriented Design and Construction (PODAC) Cost Model

    E-Print Network [OSTI]

    from one rate year to another 5.2. Product Variations 5.2.1. Modify the Cost Item cost data 5 cost data 5.3.2. Modifying labor-hour estimates, labor costs, or material costs 5.3.3. ChangingThe Product Oriented Design and Construction (PODAC) Cost Model A Proposed Procedure for Product

  5. Green Roofs: Federal Energy Management Program (FEMP) Federal Technology Alert

    SciTech Connect (OSTI)

    Scholz-Barth, K.; Tanner, S.

    2004-09-01T23:59:59.000Z

    In a ''green roof,'' a layer of vegetation (e.g., a roof garden) covers the surface of a roof to provide shade, cooler indoor and outdoor temperatures, and effective storm-water management to reduce runoff. The main components are waterproofing, soil, and plants. There are two basic kinds: intensive and extensive. An intensive green roof often features large shrubs and trees, and it can be expensive to install and maintain. An extensive green roof features shallow soil and low-growing, horizontally spreading plants that can thrive in the alpine conditions of many rooftops. These plants do not require a lot of water or soil, and they can tolerate a significant amount of exposure to the sun and wind. This Federal Technology Alert focuses on the benefits, design, and implementation of extensive green roofs and includes criteria for their use on federal facilities.

  6. Developing Biomimetic Design Principles for the Highly Optimized and Robust Design of Products and Their Components 

    E-Print Network [OSTI]

    Wadia, Anosh Porus

    2011-10-21T23:59:59.000Z

    Engineering design methods focus on developing products that are innovative, robust, and multi-functional. In this context, the term robust refers to a product's ability to accomplish successfully its predetermined functions. ...

  7. Risk-Driven Design Processes: Balancing Efficiency with Resilience in Product Design

    E-Print Network [OSTI]

    Oehmen, Josef

    2011-01-01T23:59:59.000Z

    Current design methods and approaches focus on increasing the efficiency of the product design system by, for example, eliminating waste and focusing on value creation. However, continuing failures in the development of ...

  8. CIRP Design Conference 2009 Integrated Design and PLM Applications in Aeronautics Product Development

    E-Print Network [OSTI]

    Boyer, Edmond

    CIRP Design Conference 2009 Integrated Design and PLM Applications in Aeronautics Product and development costs, could be reached thanks to innovative design methods supported by PLM technologies and cooperation between the project partners. The paper proposes a survey on integrated design methods and PLM

  9. Super Energy Savings Performance Contracts: Federal Energy Management Program (FEMP) Program Overview (revision)

    SciTech Connect (OSTI)

    Pitchford, P.

    2001-07-05T23:59:59.000Z

    This four-page publication describes the U.S. Department of Energy's (DOE's) streamlined energy savings performance contracting, or ''Super ESPC,'' process, which is managed by DOE's Federal Energy Management Program (FEMP). Under a Super ESPC, a qualifying energy service company (ESCO) from the private sector pays for energy efficiency improvements or advanced renewable energy technologies (e.g., photovoltaic systems, wind turbines, or geothermal heat pumps, among others) for a facility of a government agency. The ESCO is then repaid over time from the agency's resulting energy cost savings. Delivery orders under these contracts specify the level of performance (energy savings) and the repayment schedule; the contract term can be up to 25 years, although many Super ESPCs are for about 10 years or less.

  10. The FEMP Awards Program: Fostering Institutional Change and Energy Management Excellence

    SciTech Connect (OSTI)

    McDermott, Christa; Malone, Elizabeth L.

    2014-05-20T23:59:59.000Z

    This report assesses the use of institutional change principles and the institutional impact of award-winning projects through interviews with 22 Department of Energy Federal Energy Management Program (DOE FEMP) award winners. Award winners identified institutional facilitators and barriers in their projects and programs as well as factors in their implementation processes, thus providing information that can guide other efforts. We found that award winners do use strategies based on eight principles of institutional change, most frequently in terms of making changes to infrastructure, engaging leadership, and capitalizing on multiple motivations for making an energy efficiency improvement. The principles drawn on the least often were commitment and social empowerment. Award winners also faced five major types of obstacles that were institutional in nature: lack of resources, constraints of rules, psychological barriers, lack of information, and communication problems. We also used the seven categories of Energy Management Excellence (EME) as a lens to interpret the interview data and assess whether these categories relate to established institutional change principles. We found that the eight principles reflect strategies that have been found to be useful in improving energy efficiency in organizations, whereas the EME categories capture more of a blend of social contextual factors and strategies. The EME categories fill in some of the social context gaps that facilitate institutional change and energy management excellence, for example, personal persistence, a culture that supports creativity and innovation, regular engagement with tenants, contractors, and staff at all levels. Taking together the use of principles, EME criteria, and obstacles faced by interviewees, we make recommendations for how FEMP can better foster institutional change in federal agencies.

  11. The Komera Initiative : turning product design into public service

    E-Print Network [OSTI]

    Aust, Laura E

    2010-01-01T23:59:59.000Z

    Every mechanical engineering student at MIT takes the same courses: 2.009 being one of them. In our capstone product design course at MIT, most students glean an incredible amount from their teams, mentors, and projects, ...

  12. Multidisciplinary design problem solving on product development teams

    E-Print Network [OSTI]

    Bernstein, Joshua I. (Joshua Ian), 1974-

    2001-01-01T23:59:59.000Z

    This investigation, conducted under the auspices of the Lean Aerospace Initiative (LAI), studied how engineers from different specialties interpret and communicate about technical design problems while working on product ...

  13. Designing a flexible supply chain for new product launch

    E-Print Network [OSTI]

    Ha, Wei-Kwan Benjamin

    2005-01-01T23:59:59.000Z

    This thesis examines how companies tactically design flexible supply chains for new product launches. The research focus is on different strategies and tactics used by original equipment manufacturers to improve supply ...

  14. Integrating digital design and fabrication and craft production

    E-Print Network [OSTI]

    Kamath, Ayodh Vasant

    2009-01-01T23:59:59.000Z

    This thesis examines if methods of manual craft production can be utilised to overcome the indeterminacies of physical materials and processes that hinder Digital Design and Fabrication (DDF). Indeterminacies in physical ...

  15. Denver Federal Center Saves Energy, Forges Partnerships Through Super ESPC. Federal Energy Management Program (FEMP) ESPC Case Study

    SciTech Connect (OSTI)

    Not Available

    2002-01-01T23:59:59.000Z

    The General Services Administration is not just replacing aging heating and cooling equipment and reducing maintenance costs at the 670-acre Denver Federal Center (DFC). The GSA is also helping the government save about $450,000 in annual energy costs, conserve nearly 11 million gallons of water per year, and reduce annual carbon dioxide emissions by 15.9 million pounds, all by making use of the Department of Energy's Super Energy Savings Performance Contracts (Super ESPCs) at the DFC. Under these contracts, an energy services provider pays the up-front project costs and is then repaid over the contracts term out of the resulting energy cost savings. This two-page case study, prepared by NREL for the DOE Federal Energy Management Program (FEMP), demonstrates how the GSA forged new project partnerships, improved the DFCs boiler plant, and acquired efficient new chillers, motors, controls, and lighting by placing two delivery orders for this work under FEMPs Central Region Super ESPC.

  16. Covered Product Category: Commercial Gas Water Heaters

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including commercial gas water heaters, which are covered by the ENERGY STAR® program. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  17. Covered Product Category: Refrigerated Beverage Vending Machines

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including refrigerated beverage vending machines, which are covered by the ENERGY STAR® program. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  18. Covered Product Category: Residential Gas Storage Water Heaters

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including gas storage water heaters, which are an ENERGY STAR®-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  19. Covered Product Category: Residential Heat Pump Water Heaters

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including residential heat pump water heaters, which are an ENERGY STAR®-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  20. Covered Product Category: Residential Windows, Doors, and Skylights

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including residential windows, doors, and skylights, which are an ENERGY STAR-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  1. Advanced Turbine Systems Program: Conceptual design and product development

    SciTech Connect (OSTI)

    NONE

    1996-12-31T23:59:59.000Z

    Objective is to provide the conceptual design and product development plant for an ultra high efficiency, environmentally superior, and cost competitive industrial gas turbine system to be commercialized by the year 2000 (secondary objective is to begin early development of technologies critical to the success of ATS). This report addresses the remaining 7 of the 9 subtasks in Task 8, Design and Test of Critical Components: catalytic combustion, recuperator, high- temperature turbine disc, advanced control system, and ceramic materials.

  2. A 5 MW TRIGA reactor design for radioisotope production

    SciTech Connect (OSTI)

    Veca, Anthony R.; Whittemore, William L. [General Atomics, San Diego, CA (United States)

    1994-07-01T23:59:59.000Z

    The production and preparation of commercial-scale quantities of radioisotopes has become an important activity as their medical and industrial applications continue to expand. There are currently various large multipurpose research reactors capable of producing ample quantities of radioisotopes. These facilities, however, have many competing demands placed upon them by a wide variety of researchers and scientific programs which severely limit their radioisotope production capability. A demonstrated need has developed for a simpler reactor facility dedicated to the production of radioisotopes on a commercial basis. This smaller, dedicated reactor could provide continuous fission and activation product radioisotopes to meet commercial requirements for the foreseeable future. The design of a 5 MW TRIGA reactor facility, upgradeable to 10 MW, dedicated to the production of industrial and medical radioisotopes is discussed. A TRIGA reactor designed specifically for this purpose with its demonstrated long core life and simplicity of operation would translate into increased radioisotope production. As an example, a single TRIGA could supply the entire US needs for Mo-99. The facility is based on the experience gained by General Atomics in the design, installation, and construction of over 60 other TRIGAs over the past 35 years. The unique uranium-zirconium hydride fuel makes TRIGA reactors inexpensive to build and operate, reliable in their simplicity, highly flexible due to unique passive safety, and environmentally friendly because of minimal power requirements and long-lived fuel. (author)

  3. Surface Light Field Rendering for Virtual Product Design

    E-Print Network [OSTI]

    Behnke, Sven

    Surface Light Field Rendering for Virtual Product Design Jan MESETH, Gero MÃ?LLER, Reinhard KLEIN illumination solution including accurate materials, which is stored as an outgoing Surface Light Field (SLF-facto standard in manufacturing industries like the automotive industry. They are used, e.g., for performing

  4. Guide to FEMP-Designated Parking Lot Lighting | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy ChinaofSchaefer To: CongestionDevelopment ofofthe PublicDocument provides acquisition

  5. Guide to FEMP-Designated Parking Structure Lighting | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy ChinaofSchaefer To: CongestionDevelopment ofofthe PublicDocument provides

  6. A design tool architecture for the rapid evaluation of product design tradeoffs in an Inernet-based system modeling environment

    E-Print Network [OSTI]

    Wronski, Jacob (Jacob Andrzej)

    2005-01-01T23:59:59.000Z

    This thesis presents a computer-aided design tool for the rapid evaluation of design tradeoffs in an integrated product modeling environment. The goal of this work is to provide product development organizations with better ...

  7. Mu2e production solenoid cryostat conceptual design

    SciTech Connect (OSTI)

    Nicol, T.H.; Kashikhin, V.V.; Page, T.M.; Peterson, T.J.; /Fermilab

    2011-06-01T23:59:59.000Z

    Mu2e is a muon-to-electron conversion experiment being designed by an international collaboration of more than 65 scientists and engineers from more than 20 research institutions for installation at Fermilab. The experiment is comprised of three large superconducting solenoid magnet systems, production solenoid (PS), transport solenoid (TS) and detector solenoid (DS). A 25 kW, 8 GeV proton beam strikes a target located in the PS creating muons from the decay of secondary particles. These muons are then focused in the PS and the resultant muon beam is transported through the TS towards the DS. The production solenoid presents a unique set of design challenges as the result of high radiation doses, stringent magnetic field requirements, and large structural forces. This paper describes the conceptual design of the PS cryostat and will include discussions of the vacuum vessel, thermal shield, multi-layer insulation, cooling system, cryogenic piping, and suspension system.

  8. Sell Energy-Efficient Products (Fact Sheet), Federal Energy Management Program (FEMP)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOriginEducationVideo »UsageSecretary of Energy Advisory10 March 2010Self-powered Hydrogen +By

  9. Buy Energy-Efficient Products (Fact Sheet), Federal Energy Management Program (FEMP)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof Energy FutureDepartment ofBUILDING-TO-GRIDLight WaPROJECTS FUNDED BY

  10. Switchable photosystem-II designer algae for photobiological hydrogen production

    DOE Patents [OSTI]

    Lee, James Weifu (Knoxville, TN)

    2010-01-05T23:59:59.000Z

    A switchable photosystem-II designer algae for photobiological hydrogen production. The designer transgenic algae includes at least two transgenes for enhanced photobiological H.sub.2 production wherein a first transgene serves as a genetic switch that can controls photosystem II (PSII) oxygen evolution and a second transgene encodes for creation of free proton channels in the algal photosynthetic membrane. In one embodiment, the algae includes a DNA construct having polymerase chain reaction forward primer (302), a inducible promoter (304), a PSII-iRNA sequence (306), a terminator (308), and a PCR reverse primer (310). In other embodiments, the PSII-iRNA sequence (306) is replaced with a CF.sub.1-iRNA sequence (312), a streptomycin-production gene (314), a targeting sequence (316) followed by a proton-channel producing gene (318), or a PSII-producing gene (320). In one embodiment, a photo-bioreactor and gas-product separation and utilization system produce photobiological H.sub.2 from the switchable PSII designer alga.

  11. Costs Models in Design and Manufacturing of Sand Casting Products

    E-Print Network [OSTI]

    Nicolas Perry; Magali Mauchand; Alain Bernard

    2010-11-26T23:59:59.000Z

    In the early phases of the product life cycle, the costs controls became a major decision tool in the competitiveness of the companies due to the world competition. After defining the problems related to this control difficulties, we will present an approach using a concept of cost entity related to the design and realization activities of the product. We will try to apply this approach to the fields of the sand casting foundry. This work will highlight the enterprise modelling difficulties (limits of a global cost modelling) and some specifics limitations of the tool used for this development. Finally we will discuss on the limits of a generic approach.

  12. Covered Product Category: Residential Whole-Home Gas Tankless Water Heaters

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including whole-home gas tankless water heaters, which are an ENERGY STAR®-qualified product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  13. Nottingham Trent University, PhD Studentship Opportunities in Product Design, October 2014 Theme/Project

    E-Print Network [OSTI]

    Evans, Paul

    , the treatment of facial palsy and the development of new additive manufacturing techniques for medical devices product design. The research will be carried out at the Advanced Design and Manufacturing engineering of materials, pre-manufacture (product design specification, conceptual design, embodiment design and detail

  14. Accelerator driven production of tritium: target and blanket design

    E-Print Network [OSTI]

    Ragusa, Jean Concetto

    1996-01-01T23:59:59.000Z

    The growing amounts of plutonium, higher actinides (Am, Cm, Cf, . . . )t and long- lived fission products (LLFP's) due to civilian nuclear operations, and excess weapons plutonium from military arsenals are in need of disposaL Scientists &om many countries... the vessel from above. The need for a 90' beam bend requires additional beam energy to compensate for the loss in the beam power by bremsstrahlung and can be seen as a drawback for this design. Another project aimed at eliminating LLFP'S and actinide...

  15. Advanced Turbine Systems (ATS) program conceptual design and product development

    SciTech Connect (OSTI)

    NONE

    1996-08-31T23:59:59.000Z

    Achieving the Advanced Turbine Systems (ATS) goals of 60% efficiency, single-digit NO{sub x}, and 10% electric power cost reduction imposes competing characteristics on the gas turbine system. Two basic technical issues arise from this. The turbine inlet temperature of the gas turbine must increase to achieve both efficiency and cost goals. However, higher temperatures move in the direction of increased NO{sub x} emission. Improved coatings and materials technologies along with creative combustor design can result in solutions to achieve the ultimate goal. GE`s view of the market, in conjunction with the industrial and utility objectives, requires the development of Advanced Gas Turbine Systems which encompass two potential products: a new aeroderivative combined-cycle system for the industrial market, and a combined-cycle system for the utility sector that is based on an advanced frame machine. The GE Advanced Gas Turbine Development program is focused on two specific products: (1) a 70 MW class industrial gas turbine based on the GE90 core technology utilizing an innovative air cooling methodology; (2) a 200 MW class utility gas turbine based on an advanced Ge heavy-duty machine utilizing advanced cooling and enhancement in component efficiency. Both of these activities required the identification and resolution of technical issues critical to achieving ATS goals. The emphasis for the industrial ATS was placed upon innovative cycle design and low emission combustion. The emphasis for the utility ATS was placed on developing a technology base for advanced turbine cooling, while utilizing demonstrated and planned improvements in low emission combustion. Significant overlap in the development programs will allow common technologies to be applied to both products. GE Power Systems is solely responsible for offering GE products for the industrial and utility markets.

  16. A decomposition-based approach for the integration of product development and manufacturing system design

    E-Print Network [OSTI]

    Kim, Yong-Suk, 1975-

    2002-01-01T23:59:59.000Z

    Using a structured approach to understand the interaction between product design decisions and manufacturing system design is critical to reflect manufacturing system issues early in the product development process. Early ...

  17. Risk Management in Product Design: Current State, Conceptual Model and Future Research

    E-Print Network [OSTI]

    Oehmen, Josef

    Risk management is an important element of product design. It helps to minimize the project- and product-related risks such as project budget and schedule overrun, or missing product cost and quality targets. Risk management ...

  18. M-C Power`s product design and improvement

    SciTech Connect (OSTI)

    Scroppo, J.A.; Laurens, R.M.; Petraglia, V.J.

    1995-12-31T23:59:59.000Z

    The sole mission of M-C Power is the development and subsequent commercialization of molten carbonate fuel cell (MCFC) stacks. These MCFC stacks are based on the Internally Manifolded Heat EXchanger plate design developed by the Institute of Gas Technology. Integration of the MCFC stack into a commercially viable power plant is the mission of the IMHEX{sup {reg_sign}} team. The team is composed of leaders in the packaging and design of power generation equipment, including fuel cell technology, and includes Stewart & Stevenson, Bechtel, The Institute of Gas Technology and M-C Power. In an effort to succeed in their respective missions, M-C Power and the IMHEX{sup {reg_sign}} team have developed a commercialization program. At the present time, the team is making the transition from Phase I (Technology Development) to Phase II (Product Design & Improvement) of the program. Phase II`s objective is a commercially viable (cost effective and technologically reliable) MCFC power plant ready for market by the turn of the century.

  19. Distributed & conceptual CAD (DC-CAD) : a new software solution for product design

    E-Print Network [OSTI]

    Egan, Mark D. (Mark Douglas), 1985-

    2007-01-01T23:59:59.000Z

    Many computer aided design (CAD) software packages focus on detailed design and not on early stage, conceptual design. The ability to conceptualize and sketch early versions of a product solution is currently limited to ...

  20. Covered Product Category: Uninterruptible Power Supplies (for Data Center, Computer, and Telecommunication Applications)

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including uninterruptible power supplies (UPS), which are covered by the ENERGY STAR® program. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  1. Computer simulations suggest a new strategy to design enhanced enzymes for biofuels production.

    E-Print Network [OSTI]

    Computer simulations suggest a new strategy to design enhanced enzymes for biofuels production in the production of biofuels. Glycosylation is the covalent attachment of carbohydrate molecules to protein side to designing enhanced enzymes for biofuels production. More generally, this work suggests that tuning

  2. Universal Design Rules from Product Pairs and Association Rule Based Learning

    E-Print Network [OSTI]

    Cowen, Nicholas L.

    2010-07-14T23:59:59.000Z

    A product pair is two products with similar functionality that satisfy the same high level need but are different by design. The goal of this research is to apply association rule-based learning to product pairs and develop universal design rules...

  3. Extended Product and Process Analysis aNd Design 20 & 21 March 2008

    E-Print Network [OSTI]

    Boyer, Edmond

    and to conceive a roadmap for future trainings of various employees of the firm during the lifecycle of a product of the product lifecycle. The use of knowledge as an element of differentiation strategy is a quite complexExtended Product and Process Analysis aNd Design Bordeaux 20 & 21 March 2008 Design for teaching

  4. DESIGN AND PERFORMANCE OF A PASSIVE RADON DECAY PRODUCTS MONITOR

    E-Print Network [OSTI]

    F. Stieff

    2006-01-01T23:59:59.000Z

    Electret-based passive air samplers have been used in United Kingdom and elsewhere for quantitative sampling for airborne dust. Alpha electret ion chambers (EIC) have been used for quantitative measurement of deposited alpha emitting isotopes. These two well documented principles are combined to create a passive radon progeny monitor. Large area (50 cm2) electret charged to 500 to 2000 volts collect airborne radon decay products and the collected sample is "viewed " and measured by an alpha EIC. Such collection and measurement continues for the entire period of sampling, providing an integrated signal to the electret in alpha EIC. The present work is of exploratory nature and provides the responses of three different sizes of collection electrets. Results are also compared with a simple passive device with no collecting electret. The study provides data for optimization of the design depending upon the requirement. Study is limited to a typical home with equilibrium ratios from 40 to 60%. This method can be used for both short term and long term monitoring of RDP in working level units.

  5. Conceptual design report -- Gasification Product Improvement Facility (GPIF)

    SciTech Connect (OSTI)

    Sadowski, R.S.; Skinner, W.H.; House, L.S.; Duck, R.R. [CRS Sirrine Engineers, Inc., Greenville, SC (United States); Lisauskas, R.A.; Dixit, V.J. [Riley Stoker Corp., Worcester, MA (United States); Morgan, M.E.; Johnson, S.A. [PSI Technology Co., Andover, MA (United States). PowerServe Div.; Boni, A.A. [PSI-Environmental Instruments Corp., Andover, MA (United States)

    1994-09-01T23:59:59.000Z

    The problems heretofore with coal gasification and IGCC concepts have been their high cost and historical poor performance of fixed-bed gasifiers, particularly on caking coals. The Gasification Product Improvement Facility (GPIF) project is being developed to solve these problems through the development of a novel coal gasification invention which incorporates pyrolysis (carbonization) with gasification (fixed-bed). It employs a pyrolyzer (carbonizer) to avoid sticky coal agglomeration caused in the conventional process of gradually heating coal through the 400 F to 900 F range. In so doing, the coal is rapidly heated sufficiently such that the coal tar exists in gaseous form rather than as a liquid. Gaseous tars are then thermally cracked prior to the completion of the gasification process. During the subsequent endothermic gasification reactions, volatilized alkali can become chemically bound to aluminosilicates in (or added to) the ash. To reduce NH{sub 3} and HCN from fuel born nitrogen, steam injection is minimized, and residual nitrogen compounds are partially chemically reduced in the cracking stage in the upper gasifier region. Assuming testing confirms successful deployment of all these integrated processes, future IGCC applications will be much simplified, require significantly less mechanical components, and will likely achieve the $1,000/kWe commercialized system cost goal of the GPIF project. This report describes the process and its operation, design of the plant and equipment, site requirements, and the cost and schedule. 23 refs., 45 figs., 23 tabs.

  6. Haha and aha! : creativity, idea generation, improvisational humor, and product design

    E-Print Network [OSTI]

    Kudrowitz, Barry M. (Barry Matthew)

    2010-01-01T23:59:59.000Z

    It is widely recognized that innovation and creativity is the new competitive battleground for product development firms. Engineers and product designers are now expected to be highly creative, prolific idea generators in ...

  7. The Sustainable Design Guidelines are the product of the ASU Office of the University Architect with the support and participation of the Sustainable Design Advisory Committee.

    E-Print Network [OSTI]

    Zhang, Junshan

    to sustainable design and construction (architecture, construction, facilities management, businessThe Sustainable Design Guidelines are the product of the ASU Office of the University Architect with the support and participation of the Sustainable Design Advisory Committee. ASU Sustainable Design

  8. Efficient buffer design algorithms for production line profit maximization

    E-Print Network [OSTI]

    Shi, Chuan, Ph. D. Massachusetts Institute of Technology

    2012-01-01T23:59:59.000Z

    A production line is a manufacturing system where machines are connected in series and separated by buffers. The inclusion of buffers increases the average production rate of the line by limiting the propagation of ...

  9. The impact of software design structure on product maintenance costs and measurement of economic benefits of product redesign

    E-Print Network [OSTI]

    Akaikine, Andrei

    2010-01-01T23:59:59.000Z

    This paper reports results of an empirical study that aimed to demonstrate the link between software product design structure and engineers' effort to perform a code modification in the context of a corrective maintenance ...

  10. A Continuous Solar Thermochemical Hydrogen Production Plant Design

    E-Print Network [OSTI]

    Luc, Wesley Wai

    Design by Wesley Wai Luc Master of Science in Chemical EngineeringDesign A Thesis submitted in partial satisfaction of the requirements for the degree Master of Science in Chemical Engineering

  11. Optimal Design of Reliable Integrated Chemical Production Site

    E-Print Network [OSTI]

    Grossmann, Ignacio E.

    grassroots plastics and chemicals production facilities in the world. (1) (1) (2) (2) #12;222 Goal Provide of meeting entire demand (while subject to discrete uncertainties). #12;33 Intermediate storage increases Intermediate D Intermediate E Product F Product C Effects of intermediate storage: Buffer of supply-demand

  12. 15.783J / 2.739J / ESD.32J Product Design and Development, Spring 2002

    E-Print Network [OSTI]

    Eppinger, Steven D.

    Covers modern tools and methods for product design and development. The cornerstone is a project in which teams of management, engineering, and industrial design students conceive, design, and prototype a physical product. ...

  13. Photobiological hydrogen production with switchable photosystem-II designer algae

    DOE Patents [OSTI]

    Lee, James Weifu

    2014-02-18T23:59:59.000Z

    A process for enhanced photobiological H.sub.2 production using transgenic alga. The process includes inducing exogenous genes in a transgenic alga by manipulating selected environmental factors. In one embodiment inducing production of an exogenous gene uncouples H.sub.2 production from existing mechanisms that would downregulate H.sub.2 production in the absence of the exogenous gene. In other embodiments inducing an exogenous gene triggers a cascade of metabolic changes that increase H.sub.2 production. In some embodiments the transgenic alga are rendered non-regenerative by inducing exogenous transgenes for proton channel polypeptides that are targeted to specific algal membranes.

  14. Free Form Sketching System forFree Form Sketching System for Product Design Using VirtualProduct Design Using Virtual

    E-Print Network [OSTI]

    Akgunduz, Ali

    --timetime Generated images can be saved in computerGenerated images can be saved in computer Modifications can be done efficientlyModifications can be done efficiently Designs can be reviewed in more details during theDesigns can

  15. Improving Product and Manufacturing Process Design through a...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    enable more accurate modeling of machining processes, which will result in improved productivity. Graphic credit Third Wave Systems. fluid. This inefficient trial-and-error process...

  16. Information Hiding in Product Development: The Design Churn Effect

    E-Print Network [OSTI]

    Whitney, Daniel

    2002-06-07T23:59:59.000Z

    Execution of a complex product development project is facilitated through its decomposition into an interrelated set of localized development tasks. When a local ...

  17. Extended Product and Process Analysis aNd Design 20 & 21 March 2008

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    . Introduction Product Lifecycle Management systems are used in industrial enterprises wishing to manage their products data and knowledge, in all phases of their lifecycle (design, manufacturing, recycling, etc for all information and activities related to the product lifecycle. However, SMEs remain reluctant

  18. International Symposium for Engineering Education, 2007, Dublin City University, Ireland TO DESIGN PRODUCT FOR LEARNING

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    is put on the knowledge and know-how generated by product itself and its lifecycle. The goal of any firm account the knowledge generated by the product during its lifecycle. The concepts developed here would such as design phase or other phases of the product lifecycle. For example, De Martino [5] treats the multi

  19. Article Revue XXX DESIGN AND VALIDATION OF A PRODUCT-DRIVEN CONTROL SYSTEM BASED ON A

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    can be an active actor throughout its lifecycle by associating the material flow with the product is innovative in that the product can be an active actor throughout its lifecycle, taking advantageArticle Revue XXX 1 DESIGN AND VALIDATION OF A PRODUCT-DRIVEN CONTROL SYSTEM BASED ON A SIX SIGMA

  20. OCTOBER 2010 SPECIAL INSTRUCTIONS TO DESIGNERS SID-S SUSTAINABLE PRODUCTS PORTFOLIO

    E-Print Network [OSTI]

    Kamat, Vineet R.

    by the Sustainability Team at the University of Michigan (U-M) Department of Architecture, Engineering & ConstructionSID-S OCTOBER 2010 SPECIAL INSTRUCTIONS TO DESIGNERS SID-S SUSTAINABLE PRODUCTS PORTFOLIO Page 1 of 2 SUSTAINABLE PRODUCTS PORTFOLIO General The Sustainable Products Portfolio (SPP) is maintained

  1. Photobioreactor Design for Commercial Biofuel Production from Microalgae Aditya M. Kunjapur* and R. Bruce Eldridge

    E-Print Network [OSTI]

    Eldridge, R. Bruce

    neutral fuel), and increased biofuel production would supplement nonrenewable energy sources.2 MicroalgaePhotobioreactor Design for Commercial Biofuel Production from Microalgae Aditya M. Kunjapur* and R This review paper describes systems used to cultivate microalgae for biofuel production. It addresses general

  2. A Continuous Solar Thermochemical Hydrogen Production Plant Design

    E-Print Network [OSTI]

    Luc, Wesley Wai

    Plant Production 5000 kg/day Solar Plant Module Cost (with2, which was a solar thermal plant built by the Departmentfor a continuous solar thermochemical plant was modeled and

  3. Product Design and Innovation Arthur L. Rosenthal, PhD

    E-Print Network [OSTI]

    Vajda, Sandor

    Draft by October 27 · 10/27 Risk Management - FMEA tool · AS12 Draft FMEA for Project Product - hard copy and PDF by Oct. 29 · 10/29 FMEA Workshop · AS13 Prepare Final Project Prodcut FMEA - hard copy

  4. Improved inventory and production control on a multi-product production line : seasonality analysis, inventory supermarket, and Kanban design

    E-Print Network [OSTI]

    Zhong, Yuan, M. Eng. Massachusetts Institute of Technology

    2009-01-01T23:59:59.000Z

    This research creates a system to help PDAP Electronics Singapore control its inventories and achieve demand-driven production on a multiple-product production line. One stage is chosen for study in this thesis. An inventory ...

  5. ADVANCED TURBINE SYSTEM CONCEPTUAL DESIGN AND PRODUCT DEVELOPMENT - Final Report

    SciTech Connect (OSTI)

    Albrecht H. Mayer

    2000-07-15T23:59:59.000Z

    Asea Brown Boveri (ABB) has completed its technology based program. The results developed under Work Breakdown Structure (WBS) 8, concentrated on technology development and demonstration have been partially implemented in newer turbine designs. A significant improvement in heat rate and power output has been demonstrated. ABB will use the knowledge gained to further improve the efficiency of its Advanced Cycle System, which has been developed and introduced into the marked out side ABB's Advanced Turbine System (ATS) activities. The technology will lead to a power plant design that meets the ATS performance goals of over 60% plant efficiency, decreased electricity costs to consumers and lowest emissions.

  6. Accelerator driven production of tritium: target and blanket design 

    E-Print Network [OSTI]

    Ragusa, Jean Concetto

    1996-01-01T23:59:59.000Z

    investigated. The target designs in the heterogeneous systems were 1 / liquid lead, and 2/ layers of solid lead plates cooled by heavy water. The tritium breeding blanket assemblies contained either lithium oxide or molten fluorine salt with or without UF4...

  7. Human-Centered Sustainable Product Design Life Cycle

    E-Print Network [OSTI]

    Agogino, Alice M.

    Use per Unit Refrigerator Size (cubic feet) Refrigerator Price in 1983 Dollars $ 1,270 $ 462 "THE ART, 1999 - 24:33-82. FRIA Refrigerator Fact: Refrigerators consume 10-15% of all household energyCharge ·! Human-powered designs eliminate the need for batteries or use-phase electricity consumption, thereby

  8. Best Practices Guide for Energy-Efficient Data Center Design: Revised March 2011, Federal Energy Management Program (FEMP) (Brochure)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureCommentsEnergy Christopher| Departmentofof Energy Best

  9. Effects of federal risk management programs on investment, production, and contract design under uncertainty

    E-Print Network [OSTI]

    Seo, Sangtaek

    2006-04-12T23:59:59.000Z

    programs on investment, production, and contract design are investigated. The dissertation is comprised of three essays. The unifying theme of these essays is the economic analysis of crop insurance programs. The first essay examines the effects of revenue...

  10. Three essays on strategic and tactical issues in product design by Matthew Selove.

    E-Print Network [OSTI]

    Selove, Matthew McCloud

    2010-01-01T23:59:59.000Z

    This dissertation consists of three essays on strategic and tactical issues in product design. The first essay presents a dynamic investment game in which firms that are initially identical develop assets which are specialized ...

  11. Accelerator production of tritium pollution prevention design assessment

    SciTech Connect (OSTI)

    Reynolds, R.; Nowacki, P.; Sheetz, S.O. [Westinghouse Savannah River Co., Aiken, SC (United States); Lanik, P. [Burns and Roe Engineering Inc. (United States)

    1997-09-18T23:59:59.000Z

    This Pollution Prevention Design Assessment (PPDA) provides data for cost-benefit analysis of the potential environmental impact of the APT, is an integral part of pollution prevention/waste minimization, and is required by DOE for any activity generating radioactive, hazardous, and mixed wastes. It will also better position the APT to meet future requirements, since it is anticipated that regulatory and other requirements will continue to become more restrictive and demanding.

  12. SC Beta Graded Cavity Design for a Proposed 350 MHZ Linac for Waste Transmutation and Energy Production

    E-Print Network [OSTI]

    Barni, D; Pagani, C; Pierini, P; Visona, S; Gemme, G; Parodi, R

    1998-01-01T23:59:59.000Z

    SC Beta Graded Cavity Design for a Proposed 350 MHZ Linac for Waste Transmutation and Energy Production

  13. Designating Efficiency Levels for Product Categories | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube| DepartmentStatementDepartment ofVisits KazakhstanSummitMill Tailings |Products

  14. A Unified CAD-PLM Architecture for Improving Electronics Design Productivity through

    E-Print Network [OSTI]

    California at Los Angeles, University of

    A Unified CAD-PLM Architecture for Improving Electronics Design Productivity through Automation this manufacturing view a broad class of tools known as Product Lifecycle Management (PLM) have evolved to the supply chain (managed through PLM tools) and performance and specification data known to the engineering

  15. Emerging Furniture Design Challenges and Product Development -Plus-size Furniture and Adjustable Furniture

    E-Print Network [OSTI]

    Emerging Furniture Design Challenges and Product Development - Plus-size Furniture and Adjustable population, · Furniture with reduced environmental impact, · Furniture lifecycle and end-of-life disposal of Problem: Adjustable furniture is a high-end product which provides customers more options to increase

  16. SSC dipole log manget model cryostat design and initial production experience

    SciTech Connect (OSTI)

    Niemann, R.C.; Carson, J.A.; Engler, N.H.; Gonczy, J.D.; Nicol, T.H.

    1986-06-01T23:59:59.000Z

    The SSC dipole magnet development program includes the design and construction of full length magnet models for heat leak and magnetic measurements and for the evaluation of the performance of strings of magnets. The design of the model magnet cryostat is presented and the production experiences for the initial long magnet model, a heat leak measurement device, are related.

  17. Designing an on-line multimedia maintenance manual for a production environment

    E-Print Network [OSTI]

    Brinkman, Willem-Paul

    ). It is a combination of design-out maintenance (DOM) and preventive maintenance. The focus of DOM is to improve36 Designing an on-line multimedia maintenance manual for a production environment W.P. Brinkman, V.P. Buil, R. Cullen1 , R. Gobits2 and F.L. van Nes e-mail: w.p.brinkman@tue.nl Abstract Maintenance

  18. DESIGNING BOTTLE PRODUCTS USING ENVIRONMENTAL CRITERIA Dr. Nicholas Bilalis, Dr. Evan Diamadopoulos, Vassilis Kouroublakis,

    E-Print Network [OSTI]

    Aristomenis, Antoniadis

    cycle has a reasonable impact to the environment. More materials (metal, glass, plastic) per bottle lead1 DESIGNING BOTTLE PRODUCTS USING ENVIRONMENTAL CRITERIA Dr. Nicholas Bilalis, Dr. Evan criteria. This paper reports on the development of a methodology for designing bottles using specific

  19. Process Design for Production of Thai Rosewood -glucosidase in Pichia pastoris

    E-Print Network [OSTI]

    Enfors, Sven-Olof

    Process Design for Production of Thai Rosewood -glucosidase in Pichia pastoris Licentiate Thesis of Technology (KTH) SE-106 91 Stockholm, Sweden Stockholm 2005 ISBN 91-7178-081-5 #12;Process Design of Biotechnology Royal Institute of Technology Stockholm, Sweden Abstract A Pichia pastoris based process

  20. Domestic Water Conservation Technologies: Federal Energy Management Program (FEMP) Federal Technology Alert (Booklet)

    SciTech Connect (OSTI)

    Not Available

    2002-10-01T23:59:59.000Z

    Executive Order 13123 calls for the Federal government to conserve water as well as energy in its 500,000 facilities. To help set priorities among water-saving measures, the Federal Energy Management Program conducted a study of Federal water use in 1997. The study indicated that the government consumes more than 50% of its water in just three types of Federal facilities: housing, hospitals, and office buildings. These facilities have enough kitchens, rest rooms, and laundry areas to provide facility managers with many opportunities to begin reducing their water use (and utility costs) with appropriate water-saving fixtures and products. Therefore, this Federal Technology Alert focuses on domestic technologies, products, and appliances such as water-efficient faucets, showerheads, toilets, urinals, washing machines, and dishwashers. Conserving water also saves the energy needed to treat, pump, and heat that water in homes, businesses, and other buildings.

  1. FEMP case study: Regional super ESPC saves energy and dollars at NASA Johnson Space Center

    SciTech Connect (OSTI)

    Pitchford, P.; Dominick, J.

    1999-10-05T23:59:59.000Z

    This case study describes the new energy-efficient equipment being installed at NASA Johnson Space Center in Houston, Texas, to save nearly $2 million per year in energy and utility costs. The work is being done under a delivery order by Honeywell, Inc., as part of a US Department of Energy ``super'' regional energy savings performance contract, or Super ESPC. These are streamlined contracts that allow Federal agencies to contract with competitively selected energy service companies in their region for a variety of energy- and water-efficient products and services. The service companies pay up-front capital costs and are reimbursed with part of the agency's utility cost savings. In this work, NASA Johnson Space Center will get new energy-efficient lighting and compressed-air systems, water-conserving fixtures, and improved controls.

  2. Analysis of Improved Reference Design for a Nuclear-Driven High Temperature Electrolysis Hydrogen Production Plant

    SciTech Connect (OSTI)

    Edwin A. Harvego; James E. O'Brien; Michael G. McKellar

    2010-06-01T23:59:59.000Z

    The use of High Temperature Electrolysis (HTE) for the efficient production of hydrogen without the greenhouse gas emissions associated with conventional fossil-fuel hydrogen production techniques has been under investigation at the Idaho National Engineering Laboratory (INL) for the last several years. The activities at the INL have included the development, testing and analysis of large numbers of solid oxide electrolysis cells, and the analyses of potential plant designs for large scale production of hydrogen using an advanced Very-High Temperature Reactor (VHTR) to provide the process heat and electricity to drive the electrolysis process. The results of these system analyses, using the UniSim process analysis software, have shown that the HTE process, when coupled to a VHTR capable of operating at reactor outlet temperatures of 800 °C to 950 °C, has the potential to produce the large quantities of hydrogen needed to meet future energy and transportation needs with hydrogen production efficiencies in excess of 50%. In addition, economic analyses performed on the INL reference plant design, optimized to maximize the hydrogen production rate for a 600 MWt VHTR, have shown that a large nuclear-driven HTE hydrogen production plant can to be economically competitive with conventional hydrogen production processes, particularly when the penalties associated with greenhouse gas emissions are considered. The results of this research led to the selection in 2009 of HTE as the preferred concept in the U.S. Department of Energy (DOE) hydrogen technology down-selection process. However, the down-selection process, along with continued technical assessments at the INL, has resulted in a number of proposed modifications and refinements to improve the original INL reference HTE design. These modifications include changes in plant configuration, operating conditions and individual component designs. This paper describes the resulting new INL reference design and presents results of system analyses performed to optimize the design and to determine required plant performance and operating conditions.

  3. Advanced product realization through model-based design and virtual prototyping

    SciTech Connect (OSTI)

    Andreas, R.D. [Sandia National Labs., Albuquerque, NM (United States). Electronic Subsystems Center

    1995-03-01T23:59:59.000Z

    Several government agencies and industrial sectors have recognized the need for, and payoff of, investing in the methodologies and associated technologies for improving the product realization process. Within the defense community as well as commercial industry, there are three major needs. First, they must reduce the cost of military products, of related manufacturing processes, and of the enterprises that have to be maintained. Second, they must reduce the time required to realize products while still applying the latest technologies. Finally, they must improve the predictability of process attributes, product performance, cost, schedule and quality. They must continue to advance technology, quickly incorporate their innovations in new products and in processes to produce them, and they need to capitalize on the raw computational power and communications bandwidth that continues to become available at decreasing cost. Sandia National Laboratories initiative is pursuing several interrelated, key concepts and technologies in order to enable such product realization process improvements: model-based design; intelligent manufacturing processes; rapid virtual and physical prototyping; and agile people/enterprises. While progress in each of these areas is necessary, this paper only addresses a portion of the overall initiative. First a vision of a desired future capability in model-based design and virtual prototyping is presented. This is followed by a discussion of two specific activities parametric design analysis of Synthetic Aperture Radars (SARs) and virtual prototyping of miniaturized high-density electronics -- that exemplify the vision as well as provide a status report on relevant work in progress.

  4. Conceptual design of a new homogeneous reactor for medical radioisotope Mo-99/Tc-99m production

    SciTech Connect (OSTI)

    Liem, Peng Hong [Nippon Advanced Information Service (NAIS Co., Inc.) Scientific Computational Division, 416 Muramatsu, Tokaimura, Ibaraki (Japan); Tran, Hoai Nam [Chalmers University of Technology, Dept. of Applied Physics, Div. of Nuclear Engineering, SE-412 96 Gothenburg (Sweden); Sembiring, Tagor Malem [National Nuclear Energy Agency (BATAN), Center for Reactor Technology and Nuclear Safety, Kawasan Puspiptek, Serpong, Tangerang Selatan, Banten (Indonesia); Arbie, Bakri [PT MOTAB Technology, Kedoya Elok Plaza Blok DA 12, Jl. Panjang, Kebun Jeruk, Jakarta Barat (Indonesia)

    2014-09-30T23:59:59.000Z

    To partly solve the global and regional shortages of Mo-99 supply, a conceptual design of a nitrate-fuel-solution based homogeneous reactor dedicated for Mo-99/Tc-99m medical radioisotope production is proposed. The modified LEU Cintichem process for Mo-99 extraction which has been licensed and demonstrated commercially for decades by BATAN is taken into account as a key design consideration. The design characteristics and main parameters are identified and the advantageous aspects are shown by comparing with the BATAN's existing Mo-99 supply chain which uses a heterogeneous reactor (RSG GAS multipurpose reactor)

  5. Control Structure Design for Optimal Operation of 4-Product Thermally Coupled Columns

    E-Print Network [OSTI]

    Skogestad, Sigurd

    Control Structure Design for Optimal Operation of 4-Product Thermally Coupled Columns Deeptanshu: distillation, thermal coupling, Kaibel column, Petlyuk column Prepared for presentation at the James R. Fair distillation arrangements like Kaibel and Petlyuk columns can be challenging. This paper discusses the control

  6. V-Miner: Using Enhanced Parallel Coordinates to Mine Product Design and Test Data 1

    E-Print Network [OSTI]

    Liu, Bing

    V-Miner: Using Enhanced Parallel Coordinates to Mine Product Design and Test Data 1 Kaidi Zhao patterns can be easily detected visually. The Visual Miner (V-Miner) software includes both automated or data mining. This paper begins with an introduction to the proposed techniques and the V-Miner system

  7. ME 4171 Environmentally Conscious Design & Manufacturing (Bras) Assignment Aircraft Fuel Tank Production Pollution Prevention

    E-Print Network [OSTI]

    mainly in the aircraft industry. The main reasons for using fabric in the construction of these tanks Production Pollution Prevention A local company manufactures a wide variety of fabric fuel tanks for use are durability and shape requirements imposed by aircraft design. The construction process involves first

  8. Submitted to The First World Congress on Integrated Design and Process Technology Integrated Production Systems for

    E-Print Network [OSTI]

    Foss, Bjarne A.

    and petrochemical plants, oil-processing plants including re neries, pulp and paper plants, metallurgical plantsSubmitted to The First World Congress on Integrated Design and Process Technology Integrated Production Systems for The Process Industries yBjarne A. Foss 1, zRoger Klev, zMorten Levin, xKristian Lien y

  9. From Waste to Hydrogen: An Optimal Design of Energy Production and Distribution Network

    E-Print Network [OSTI]

    Fan, Yueyue

    impacts on freight volumes in both rural and urban areas. This paper focuses on the optimal design to operate for small quantities of hydrogen transported over short distances. Cryogenic or liquid tanker production, including biomass feedstock availability and costs (ORNL, 2005), the costs of producing hydrogen

  10. Approaches for Identifying Consumer Preferences for the Design of Technology Products: A Case Study of Residential Solar Panels

    E-Print Network [OSTI]

    Chen, Heidi Q.

    This paper investigates ways to obtain consumer preferences for technology products to help designers identify the key attributes that contribute to a product's market success. A case study of residential photovoltaic ...

  11. Approaches for identifying consumer preferences for the design of technology products : a case study of residential solar panels

    E-Print Network [OSTI]

    Chen, Heidi Qianyi

    2012-01-01T23:59:59.000Z

    This thesis investigates ways to obtain consumer preferences for technology products to help designers identify the key attributes that contribute to a product's market success. A case study of residential solar PV panels ...

  12. FEMP UESC Overview

    Broader source: Energy.gov (indexed) [DOE]

    and automation and processes, in consultation with local utilities - Participate in demand response programs, where available 8 9 Better Buildings Challenge Following...

  13. FEMP Director's Blog

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 FederalTexasManager FAQS Reference Guide -SeptemberNovemberFEMA

  14. FEMP Peer Review

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 FederalTexasManager FAQS Reference Guide| Department ofPracticesPanel

  15. MDP-8 Cairo University Conference Proceeding of MDP-8, Cairo University Conference on Mechanical Design and Production Cairo, Egypt, January 4-6, 2004

    E-Print Network [OSTI]

    Coello, Carlos A. Coello

    Design and Production Cairo, Egypt, January 4-6, 2004 41 DESIGN OF LAYERED STRUCTURES WITH DESIRED Cairo University Conference on Mechanical Design and Production Cairo, Egypt, January 4-6, 2004 Hussein

  16. Designer organisms for photosynthetic production of ethanol from carbon dioxide and water

    DOE Patents [OSTI]

    Lee, James Weifu (Knoxville, TN)

    2011-07-05T23:59:59.000Z

    The present invention provides a revolutionary photosynthetic ethanol production technology based on designer transgenic plants, algae, or plant cells. The designer plants, designer algae, and designer plant cells are created such that the endogenous photosynthesis regulation mechanism is tamed, and the reducing power (NADPH) and energy (ATP) acquired from the photosynthetic water splitting and proton gradient-coupled electron transport process are used for immediate synthesis of ethanol (CH.sub.3CH.sub.2OH) directly from carbon dioxide (CO.sub.2) and water (H.sub.2O). The ethanol production methods of the present invention completely eliminate the problem of recalcitrant lignocellulosics by bypassing the bottleneck problem of the biomass technology. The photosynthetic ethanol-production technology of the present invention is expected to have a much higher solar-to-ethanol energy-conversion efficiency than the current technology and could also help protect the Earth's environment from the dangerous accumulation of CO.sub.2 in the atmosphere.

  17. Covered Product Category: Water-Cooled Ice Machines

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance and federal efficiency requirements for water-cooled ice machines.

  18. Advanced Turbine Systems Program conceptual design and product development. Quarterly report, November 1994--January 1995

    SciTech Connect (OSTI)

    NONE

    1995-02-01T23:59:59.000Z

    Objective of Phase II of the ATS Program is to provide the conceptual design and product development plan for anultra high efficiency, environmentally superior and cost competitive industrial gas turbine system to be commercialized by the year 2000. Technical progress covered in this report is confined to Task 4 (conversion to coal) and the nine subtasks under Task 8 (design and test of critical components). These nine subtasks address six ATS technologies: catalytic combustion, recuperator, autothermal fuel reformer, high temperature turbine disc, advanced control system, and ceramic materials.

  19. Analysis of Reference Design for Nuclear-Assisted Hydrogen Production at 750°C Reactor Outlet Temperature

    SciTech Connect (OSTI)

    Michael G. McKellar; Edwin A. Harvego

    2010-05-01T23:59:59.000Z

    The use of High Temperature Electrolysis (HTE) for the efficient production of hydrogen without the greenhouse gas emissions associated with conventional fossil-fuel hydrogen production techniques has been under investigation at the Idaho National Engineering Laboratory (INL) for the last several years. The activities at the INL have included the development, testing and analysis of large numbers of solid oxide electrolysis cells, and the analyses of potential plant designs for large scale production of hydrogen using a high-temperature gas-cooled reactor (HTGR) to provide the process heat and electricity to drive the electrolysis process. The results of this research led to the selection in 2009 of HTE as the preferred concept in the U.S. Department of Energy (DOE) hydrogen technology down-selection process. However, the down-selection process, along with continued technical assessments at the INL, has resulted in a number of proposed modifications and refinements to improve the original INL reference HTE design. These modifications include changes in plant configuration, operating conditions and individual component designs. This report describes the resulting new INL reference design coupled to two alternative HTGR power conversion systems, a Steam Rankine Cycle and a Combined Cycle (a Helium Brayton Cycle with a Steam Rankine Bottoming Cycle). Results of system analyses performed to optimize the design and to determine required plant performance and operating conditions when coupled to the two different power cycles are also presented. A 600 MWt high temperature gas reactor coupled with a Rankine steam power cycle at a thermal efficiency of 44.4% can produce 1.85 kg/s of hydrogen and 14.6 kg/s of oxygen. The same capacity reactor coupled with a combined cycle at a thermal efficiency of 42.5% can produce 1.78 kg/s of hydrogen and 14.0 kg/s of oxygen.

  20. Heating, Ventilation, and Air Conditioning Design Strategy for a Hot-Humid Production Builder

    SciTech Connect (OSTI)

    Kerrigan, P.

    2014-03-01T23:59:59.000Z

    BSC worked directly with the David Weekley Homes - Houston division to redesign three floor plans in order to locate the HVAC system in conditioned space. The purpose of this project is to develop a cost effective design for moving the HVAC system into conditioned space. In addition, BSC conducted energy analysis to calculate the most economical strategy for increasing the energy performance of future production houses. This is in preparation for the upcoming code changes in 2015. The builder wishes to develop an upgrade package that will allow for a seamless transition to the new code mandate. The following research questions were addressed by this research project: 1. What is the most cost effective, best performing and most easily replicable method of locating ducts inside conditioned space for a hot-humid production home builder that constructs one and two story single family detached residences? 2. What is a cost effective and practical method of achieving 50% source energy savings vs. the 2006 International Energy Conservation Code for a hot-humid production builder? 3. How accurate are the pre-construction whole house cost estimates compared to confirmed post construction actual cost? BSC and the builder developed a duct design strategy that employs a system of dropped ceilings and attic coffers for moving the ductwork from the vented attic to conditioned space. The furnace has been moved to either a mechanical closet in the conditioned living space or a coffered space in the attic.

  1. HVAC Design Strategy for a Hot-Humid Production Builder, Houston, Texas (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2014-03-01T23:59:59.000Z

    BSC worked directly with the David Weekley Homes - Houston division to redesign three floor plans in order to locate the HVAC system in conditioned space. The purpose of this project is to develop a cost effective design for moving the HVAC system into conditioned space. In addition, BSC conducted energy analysis to calculate the most economical strategy for increasing the energy performance of future production houses. This is in preparation for the upcoming code changes in 2015. The builder wishes to develop an upgrade package that will allow for a seamless transition to the new code mandate. The following research questions were addressed by this research project: 1. What is the most cost effective, best performing and most easily replicable method of locating ducts inside conditioned space for a hot-humid production home builder that constructs one and two story single family detached residences? 2. What is a cost effective and practical method of achieving 50% source energy savings vs. the 2006 International Energy Conservation Code for a hot-humid production builder? 3. How accurate are the pre-construction whole house cost estimates compared to confirmed post construction actual cost? BSC and the builder developed a duct design strategy that employs a system of dropped ceilings and attic coffers for moving the ductwork from the vented attic to conditioned space. The furnace has been moved to either a mechanical closet in the conditioned living space or a coffered space in the attic.

  2. Production of Gasoline and Diesel from Biomass via Fast Pyrolysis, Hydrotreating and Hydrocracking: A Design Case

    SciTech Connect (OSTI)

    Jones, Susanne B.; Valkenburt, Corinne; Walton, Christie W.; Elliott, Douglas C.; Holladay, Johnathan E.; Stevens, Don J.; Kinchin, Christopher; Czernik, Stefan

    2009-02-25T23:59:59.000Z

    The purpose of this study is to evaluate a processing pathway for converting biomass into infrastructure-compatible hydrocarbon biofuels. This design case investigates production of fast pyrolysis oil from biomass and the upgrading of that bio-oil as a means for generating infrastructure-ready renewable gasoline and diesel fuels. This study has been conducted using similar methodology and underlying basis assumptions as the previous design cases for ethanol. The overall concept and specific processing steps were selected because significant data on this approach exists in the public literature. The analysis evaluates technology that has been demonstrated at the laboratory scale or is in early stages of commercialization. The fast pyrolysis of biomass is already at an early stage of commercialization, while upgrading bio-oil to transportation fuels has only been demonstrated in the laboratory and at small engineering development scale. Advanced methods of pyrolysis, which are under development, are not evaluated in this study. These may be the subject of subsequent analysis by OBP. The plant is designed to use 2000 dry metric tons/day of hybrid poplar wood chips to produce 76 million gallons/year of gasoline and diesel. The processing steps include: 1.Feed drying and size reduction 2.Fast pyrolysis to a highly oxygenated liquid product 3.Hydrotreating of the fast pyrolysis oil to a stable hydrocarbon oil with less than 2% oxygen 4.Hydrocracking of the heavy portion of the stable hydrocarbon oil 5.Distillation of the hydrotreated and hydrocracked oil into gasoline and diesel fuel blendstocks 6. Hydrogen production to support the hydrotreater reactors. The "as received" feedstock to the pyrolysis plant will be "reactor ready". This development will likely further decrease the cost of producing the fuel. An important sensitivity is the possibility of co-locating the plant with an existing refinery. In this case, the plant consists only of the first three steps: feed prep, fast pyrolysis, and upgrading. Stabilized, upgraded pyrolysis oil is transferred to the refinery for separation and finishing into motor fuels. The off-gas from the hydrotreaters is also transferred to the refinery, and in return the refinery provides lower-cost hydrogen for the hydrotreaters. This reduces the capital investment. Production costs near $2/gal (in 2007 dollars) and petroleum industry infrastructure-ready products make the production and upgrading of pyrolysis oil to hydrocarbon fuels an economically attractive source of renewable fuels. The study also identifies technical areas where additional research can potentially lead to further cost improvements.

  3. Production of Gasoline and Diesel from Biomass via Fast Pyrolysis, Hydrotreating and Hydrocracking: A Design Case

    SciTech Connect (OSTI)

    Jones, Susanne B.; Valkenburt, Corinne; Walton, Christie W.; Elliott, Douglas C.; Holladay, Johnathan E.; Stevens, Don J.; Kinchin, Christopher; Czernik, Stefan

    2009-02-28T23:59:59.000Z

    The purpose of this study is to evaluate a processing pathway for converting biomass into infrastructure-compatible hydrocarbon biofuels. This design case investigates production of fast pyrolysis oil from biomass and the upgrading of that bio-oil as a means for generating infrastructure-ready renewable gasoline and diesel fuels. This study has been conducted using the same methodology and underlying basis assumptions as the previous design cases for ethanol. The overall concept and specific processing steps were selected because significant data on this approach exists in the public literature. The analysis evaluates technology that has been demonstrated at the laboratory scale or is in early stages of commercialization. The fast pyrolysis of biomass is already at an early stage of commercialization, while upgrading bio-oil to transportation fuels has only been demonstrated in the laboratory and at small engineering development scale. Advanced methods of pyrolysis, which are under development, are not evaluated in this study. These may be the subject of subsequent analysis by OBP. The plant is designed to use 2000 dry metric tons/day of hybrid poplar wood chips to produce 76 million gallons/year of gasoline and diesel. The processing steps include: 1.Feed drying and size reduction 2.Fast pyrolysis to a highly oxygenated liquid product 3.Hydrotreating of the fast pyrolysis oil to a stable hydrocarbon oil with less than 2% oxygen 4.Hydrocracking of the heavy portion of the stable hydrocarbon oil 5.Distillation of the hydrotreated and hydrocracked oil into gasoline and diesel fuel blendstocks 6. Hydrogen production to support the hydrotreater reactors. The “as received” feedstock to the pyrolysis plant will be “reactor ready.” This development will likely further decrease the cost of producing the fuel. An important sensitivity is the possibility of co-locating the plant with an existing refinery. In this case, the plant consists only of the first three steps: feed prep, fast pyrolysis, and upgrading. Stabilized, upgraded pyrolysis oil is transferred to the refinery for separation and finishing into motor fuels. The off-gas from the hydrotreaters is also transferred to the refinery, and in return the refinery provides lower-cost hydrogen for the hydrotreaters. This reduces the capital investment. Production costs near $2/gal (in 2007 dollars) and petroleum industry infrastructure-ready products make the production and upgrading of pyrolysis oil to hydrocarbon fuels an economically attractive source of renewable fuels. The study also identifies technical areas where additional research can potentially lead to further cost improvements.

  4. Advanced turbine systems program conceptual design and product development. Quarterly report, August--October, 1994

    SciTech Connect (OSTI)

    NONE

    1995-01-01T23:59:59.000Z

    The objective of Phase 2 of the Advanced Turbine Systems (ATS) Program is to provide the conceptual design and product development plan for an ultra-high efficiency, environmentally superior and cost competitive industrial gas turbine system to be commercialized by the year 2000. A secondary objective is to begin early development of technologies critical to the success of ATS. During this report period, the following tasks were completed: Market study; System definition and analysis; and Integrated program plans. Progress on Task 8, Design and Test of Critical Components, is also discussed. This particular task includes expanded materials and component research covering recuperators, combustion, autothermal fuel reformation, ceramics application and advanced gas turbine system controls.

  5. Advanced Turbine Systems Program -- Conceptual design and product development. Quarterly report, August 1--October 31, 1995

    SciTech Connect (OSTI)

    NONE

    1995-12-31T23:59:59.000Z

    The objective of Phase 2 of the Advanced Turbine Systems (ATS) Program is to provide the conceptual design and product development plan for an ultra high efficiency, environmentally superior and cost competitive industrial gas turbine system to be commercialized by the year 2000. A secondary objective is to begin early development of technologies critical to the success of ATS. This quarterly report, addresses only Task 4, conversion of a gas turbine to a coal-fired gas turbine, which was completed during the quarter and the nine subtasks included in Task 8, design and test of critical components. These nine subtasks address six ATS technologies as follows: catalytic combustion; recuperator; autothermal fuel reformer; high temperature turbine disc; advanced control system (MMI); and ceramic materials.

  6. MDP-8 Cairo University Conference Proceeding of MDP-8, Cairo University Conference on Mechanical Design and Production Cairo, Egypt, January 4-6, 2004

    E-Print Network [OSTI]

    Saitou, Kazuhiro "Kazu"

    Design and Production Cairo, Egypt, January 4-6, 2004 591 CRASHWORTHINESS DESIGN USING META and Production Cairo, Egypt, January 4-6, 2004 Hamza and Saitou 592 optimization, ii) parametric optimization

  7. Molted carbonate fuel cell product design and improvement - 4th quarter, 1995. Quarterly report, October 1, 1995--December 31, 1995

    SciTech Connect (OSTI)

    NONE

    1998-04-01T23:59:59.000Z

    The primary objective of this project is to establish the commercial readiness of MW-class IMHEX Molten Carbonate Fuel Cell power plants. Progress is described on marketing, systems design and analysis, product options and manufacturing.

  8. Robust design as a driver of engine cylinder heads evolution : a framework for identifying product improvement paths

    E-Print Network [OSTI]

    Gómez de la Mora, Luz de Lourdes

    2005-01-01T23:59:59.000Z

    The fundamental goal of Robust Design is to improve the quality of a product by minimizing the effects of variation. A key contributor to robustness over the long term is R&D. Therefore, a framework is desired to help ...

  9. Some modifications to the design of a parabolic solar concentrator for construction in Lesotho and their effects on power production

    E-Print Network [OSTI]

    Ferreira, Toni (Toni Jolene)

    2005-01-01T23:59:59.000Z

    An experimental study was performed to test the effectiveness of design modifications terms of efficiency and power production in an existing parabolic solar concentrator. The proposed modifications included limiting the ...

  10. Design of an Integrated Laboratory Scale Test for Hydrogen Production via High Temperature Electrolysis

    SciTech Connect (OSTI)

    G.K. Housley; K.G. Condie; J.E. O'Brien; C. M. Stoots

    2007-06-01T23:59:59.000Z

    The Idaho National Laboratory (INL) is researching the feasibility of high-temperature steam electrolysis for high-efficiency carbon-free hydrogen production using nuclear energy. Typical temperatures for high-temperature electrolysis (HTE) are between 800º-900ºC, consistent with anticipated coolant outlet temperatures of advanced high-temperature nuclear reactors. An Integrated Laboratory Scale (ILS) test is underway to study issues such as thermal management, multiple-stack electrical configuration, pre-heating of process gases, and heat recuperation that will be crucial in any large-scale implementation of HTE. The current ILS design includes three electrolysis modules in a single hot zone. Of special design significance is preheating of the inlet streams by superheaters to 830°C before entering the hot zone. The ILS system is assembled on a 10’ x 16’ skid that includes electronics, power supplies, air compressor, pumps, superheaters, , hot zone, condensers, and dew-point sensor vessels. The ILS support system consists of three independent, parallel supplies of electrical power, sweep gas streams, and feedstock gas mixtures of hydrogen and steam to the electrolysis modules. Each electrolysis module has its own support and instrumentation system, allowing for independent testing under different operating conditions. The hot zone is an insulated enclosure utilizing electrical heating panels to maintain operating conditions. The target hydrogen production rate for the ILS is 5000 Nl/hr.

  11. Design of a Small-Scale Biodiesel Production System Jeffrey Anderson, Jessica Caceres, Ali Khazaei, Jedidiah Shirey

    E-Print Network [OSTI]

    Design of a Small-Scale Biodiesel Production System Jeffrey Anderson, Jessica Caceres, Ali Khazaei acreage and biodiesel output. Monte Carlo Simulation Objective: 1) Biodiesel Production Simulation: Determines biodiesel yield and Net Energy Ration of each crop alternative 1) Business Simulation: Determines

  12. A. Kusiak, Data Mining in Design of Products and Production Systems, Proceedings of INCOM'2006: 12th IFAC/IFIP/IFORS/IEEE Symposium on Control Problems in Manufacturing, May 2006, Saint-Etienne, France, Vol. 1, pp. 49-53.

    E-Print Network [OSTI]

    Kusiak, Andrew

    A. Kusiak, Data Mining in Design of Products and Production Systems, Proceedings of INCOM'2006: 12-Etienne, France, Vol. 1, pp. 49-53. 49 DATA MINING IN DESIGN OF PRODUCTS AND PRODUCTION SYSTEMS Andrew Kusiak://www.icaen.uiowa.edu/~ankusiak Abstract: As a new science, data mining is acquiring its own identity by refining the concepts from other

  13. Advanced turbine systems program conceptual design and product development. Annual report, August 1993--July 1994

    SciTech Connect (OSTI)

    NONE

    1994-11-01T23:59:59.000Z

    This Yearly Technical Progress Report covers the period August 3, 1993 through July 31, 1994 for Phase 2 of the Advanced Turbine Systems (ATS) Program by Solar Turbines Incorporated under DOE Contract No. DE-AC421-93MC30246. As allowed by the Contract (Part 3, Section J, Attachment B) this report is also intended to fulfill the requirements for a fourth quarterly report. The objective of Phase 2 of the ATS Program is to provide the conceptual design and product development plan for an ultra-high efficiency, environmentally superior and cost-competitive industrial gas turbine system to be commercialized in the year 2000. During the period covered by this report, Solar has completed three of eight program tasks and has submitted topical reports. These three tasks included a Project Plan submission of information required by NEPA, and the selection of a Gas-Fueled Advanced Turbine System (GFATS). In the latest of the three tasks, Solar`s Engineering team identified an intercooled and recuperated (ICR) gas turbine as the eventual outcome of DOE`s ATS program coupled with Solar`s internal New Product Introduction (NPI) program. This machine, designated ``ATS50`` will operate at a thermal efficiency (turbine shaft power/fuel LHV) of 50 percent, will emit less than 10 parts per million of NOx and will reduce the cost of electricity by 10 percent. It will also demonstrate levels of reliability, availability, maintainability, and durability (RAMD) equal to or better than those of today`s gas turbine systems. Current activity is concentrated in three of the remaining five tasks a Market Study, GFATS System Definition and Analysis, and the Design and Test of Critical Components.

  14. Theoretical Design of Molecular Electrocatalysts with Flexible Pendant Amines for Hydrogen Production and Oxidation

    SciTech Connect (OSTI)

    Fernandez, Laura; Horvath, Samantha; Hammes-Schiffer, Sharon

    2013-02-07T23:59:59.000Z

    The design of hydrogen oxidation and production catalysts is important for the development of alternative renewable energy sources. The overall objective is to maximize the turnover frequency and minimize the overpotential. In an effort to assist in the design of such catalysts, we use computational methods to examine a variety of nickel-based molecular electrocatalysts with pendant amines. Our studies focus on the proton-coupled electron transfer (PCET) process involving electron transfer between the complex and the electrode and intramolecular proton transfer between the nickel center and the nitrogen of the pendant amine. The concerted PCET mechanism, which tends to require a lower overpotential, is favored by a smaller equilibrium Ni-N distance and a more flexible pendant amine ligand, thereby decreasing the energetic penalty for the nitrogen to approach the nickel center for proton transfer. These calculations provide design principles that will be useful for developing the next generation of hydrogen catalysts. This research was supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the U. S. Department of Energy, Office of Science, Office of Basic Energy Sciences.

  15. MULTI-PERIOD CAPACITY PLANNING FOR INTEGRATED PRODUCT-PROCESS DESIGN

    E-Print Network [OSTI]

    Saitou, Kazuhiro "Kazu"

    the quality of the finished products and minimize the total production cost dur- ing the periods. The product the quality of the 415 #12;finished products and minimizes the total cost of production. The product quality and operating costs of a production facility and the quality of finished prod- ucts. Given forecasted market

  16. ARRA FEMP Technical Assistance -- Federal Aviation Administration Project 209 -- Control Tower and Support Building, Palm Springs, CA

    SciTech Connect (OSTI)

    Arends, J.; Sandusky, William F.

    2010-03-31T23:59:59.000Z

    This report represents findings of a design review team that evaluated construction documents (at the 100% level) and operating specifications for a new control tower and support building that will be built in Palm Springs, California by the Federal Aviation Administration (FAA). The focus of the review was to identify measures that could be incorporated into the final design and operating specifications that would result in additional energy savings for the FAA that would not have otherwise occurred.

  17. Advanced turbine systems program conceptual design and product development. Annual report, August 1994--July 1995

    SciTech Connect (OSTI)

    NONE

    1995-11-01T23:59:59.000Z

    This report summarizes the tasks completed under this project during the period from August 1, 1994 through July 31, 1994. The objective of the study is to provide the conceptual design and product development plan for an ultra high efficiency, environmentally superior and cost-competitive industrial gas turbine system to be commercialized by the year 2000. The tasks completed include a market study for the advanced turbine system; definition of an optimized recuperated gas turbine as the prime mover meeting the requirements of the market study and whose characteristics were, in turn, used for forecasting the total advanced turbine system (ATS) future demand; development of a program plan for bringing the ATS to a state of readiness for field test; and demonstration of the primary surface recuperator ability to provide the high thermal effectiveness and low pressure loss required to support the proposed ATS cycle.

  18. Covered Product Category: Hot Food Holding Cabinets

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for hot food holding cabinets, which are covered by the ENERGY STAR program.

  19. Covered Product Categories | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Strings Pool Pumps Water Coolers Suspended Categories Electric Motors Distribution Transformers Fluorescent Tube Lamps FEMP Home About the Program Program Areas Laws &...

  20. Covered Product Category: Commercial Steam Cookers

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial steam cookers, which are covered by the ENERGY STAR program.

  1. Covered Product Category: Commercial Refrigerators and Freezers

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for commercial refrigerators and freezers, which are covered by the ENERGY STAR program.

  2. Effect of improved target designs on the sup 238 Pu production at the Fast Flux Test Reactor

    SciTech Connect (OSTI)

    Karnesky, R.A.; Wootan, D.W.; Jordheim, D.P. (Westinghouse Hanford Co., Richland, WA (United States))

    1991-11-01T23:59:59.000Z

    This paper present the results of a series of calculations made to determine the {sup 238}Pu production potential of several advanced target assembly designs in the Fast Flux Test Facility (FFTF). These calculations show that by using advanced target designs the intimately mix the {sup 237}Np target material with an yttrium hydride moderator, the FFTF has the potential of producing up to 30 kg of high-quality {sup 238}Pu per year.

  3. Analyzing patterns of writing and sketching in the product design process

    E-Print Network [OSTI]

    Smith, Rebecca A. (Rebecca Anna)

    2009-01-01T23:59:59.000Z

    Design notebooks, or logbooks, are typically used to record notes during the design process. These notes consist of text entries as well as sketches with varying levels of detail. Previous research on the design process ...

  4. Advanced turbine systems program conceptual design and product development. Quarterly report, February 1995--April 1995

    SciTech Connect (OSTI)

    Karstensen, K.W.

    1995-07-01T23:59:59.000Z

    This Quarterly Technical Progress Report covers the period February 1, 1995, through April 30, 1995, for Phase II of the Advanced Turbine Systems (ATS) Program by Solar Turbines Incorporated under DOE contract No. DE-AC21-93MC30246. The objective of Phase II of the ATS Program is to provide the conceptual design and product development plan for an ultra high efficiency, environmentally superior and cost competitive industrial gas turbine system to be commercialized by the year 2000. A secondary objective is to begin early development of technologies critical to the success of ATS. Tasks 1, 2, 3, 5, 6 and 7 of Phase II have been completed in prior quarters. Their results have been discussed in the applicable quarterly reports and in their respective topical reports. With the exception of Task 7, final editions of these topical reports have been submitted to the DOE. This quarterly report, then, addresses only Task 4 and the nine subtasks included in Task 8, {open_quotes}Design and Test of Critical Components.{close_quotes} These nine subtasks address six ATS technologies as follows: (1) Catalytic Combustion - Subtasks 8.2 and 8.5, (2) Recuperator - Subtasks 8.1 and 8.7, (3) Autothermal Fuel Reformer - Subtask 8.3, (4) High Temperature Turbine Disc - Subtask 8.4, (5) Advanced Control System (MMI) - Subtask 8.6, and (6) Ceramic Materials - Subtasks 8.8 and 8.9. Major technological achievements from Task 8 efforts during the quarter are as follows: (1) The subscale catalytic combustion rig in Subtask 8.2 is operating consistently at 3 ppmv of NO{sub x} over a range of ATS operating conditions. (2) The spray cast process used to produce the rim section of the high temperature turbine disc of Subtask 8.4 offers additional and unplanned spin-off opportunities for low cost manufacture of certain gas turbine parts.

  5. Design for Product-Embedded Disassembly Pathways* Shingo Takeuchi and Kazuhiro Saitou

    E-Print Network [OSTI]

    Saitou, Kazuhiro "Kazu"

    Union (EU) directive on Waste Electric and Electronic Equipment (WEEE) (more than 50% of product must

  6. Reducing Technical Uncertainty in Product and ProcessReducing Technical Uncertainty in Product and Process Development Through Parallel Design of PrototypesDevelopment Through Parallel Design of Prototypes

    E-Print Network [OSTI]

    Gabrieli, John

    . Chipmakers such as Intel buy process equipment based on reliability, cost effectiveness, and performance: Semiconductor Production Equipment Applied Materials is a leading supplier of chemical vapor deposition (CVD) equipment and other process equipment used by manufacturers of semiconductor devices. Applied's CVD division

  7. Prototype Design of A Multi-agent System for Integrated Control and Asset Management of Petroleum Production Facilities

    E-Print Network [OSTI]

    Taylor, James H.

    Prototype Design of A Multi-agent System for Integrated Control and Asset Management of Petroleum Production Facilities James H. Taylor and Atalla F. Sayda Abstract-- This paper addresses a practical intelligent multi- agent system for asset management for the petroleum industry, which is crucial

  8. How managing more efficiently substances in the design process of industrial products? An example from the aeronautics sector

    E-Print Network [OSTI]

    Lemagnen, Maud; Brissaud, Daniel

    2009-01-01T23:59:59.000Z

    Lowering environmental impacts of products, i.e. ecodesign, is considered today as a new and promising approach environment protection. This article focuses on ecodesign in the aeronautical sector through the analysis of the practices of a company that designs and produces engine equipments. Noise, gas emissions, fuel consumptions are the main environmental aspects which are targeted by aeronautics. From now on, chemical risk linked to the use of materials and production processes has to be traced, not only because of regulation pressure (e.g. REACh) but also because of customers requirements. So far, the aeronautical sector hasn't been focusing much on managing chemical risks at the design stage. However, new substances regulations notably require that chemical risk management should be by industries used as early as possible in their product development process. The aeronautics sector has therefore to elaborate new chemical risk management. The aim of this paper is to present a new method hat should be adap...

  9. Review on Biomass Torrefaction Process and Product Properties and Design of Moving Bed Torrefaction System Model Development

    SciTech Connect (OSTI)

    Jaya Shankar Tumuluru; Christopher T. Wright; Shahab Sokhansanj

    2011-08-01T23:59:59.000Z

    A Review on Torrefaction Process and Design of Moving Bed Torrefaction System for Biomass Processing Jaya Shankar Tumuluru1, Shahab Sokhansanj2 and Christopher T. Wright1 Idaho National Laboratory Biofuels and Renewable Energy Technologies Department Idaho Falls, Idaho 83415 Oak Ridge National Laboratory Bioenergy Resource and Engineering Systems Group Oak Ridge, TN 37831 Abstract Torrefaction is currently developing as an important preprocessing step to improve the quality of biomass in terms of physical properties, and proximate and ultimate composition. Torrefaction is a slow heating of biomass in an inert or reduced environment to a maximum temperature of 300 C. Torrefaction can also be defined as a group of products resulting from the partially controlled and isothermal pyrolysis of biomass occurring in a temperature range of 200-230 C and 270-280 C. Thus, the process can also be called a mild pyrolysis as it occurs at the lower temperature range of the pyrolysis process. At the end of the torrefaction process, a solid uniform product with lower moisture content and higher energy content than raw biomass is produced. Most of the smoke-producing compounds and other volatiles are removed during torrefaction, which produces a final product that will have a lower mass but a higher heating value. There is a lack of literature on the design aspects of torrefaction reactor and a design sheet for estimating the dimensions of the torrefier based on capacity. This study includes (a) conducting a detailed review on the torrefaction of biomass in terms of understanding the process, product properties, off-gas compositions, and methods used, and (b) to design a moving bed torrefier, taking into account the basic fundamental heat and mass transfer calculations. Specific objectives include calculating the dimensions like diameter and height of the moving packed bed torrefier for different capacities ranging from 25-1000 kg/hr, designing the heat loads and gas flow rates, and developing an interactive excel sheet where the user can define design specifications.

  10. LSST: from Science Drivers to Reference Design and Anticipated Data Products

    E-Print Network [OSTI]

    Z. Ivezic; J. A. Tyson; B. Abel; E. Acosta; R. Allsman; Y. AlSayyad; S. F. Anderson; J. Andrew; R. Angel; G. Angeli; R. Ansari; P. Antilogus; K. T. Arndt; P. Astier; E. Aubourg; T. Axelrod; D. J. Bard; J. D. Barr; A. Barrau; J. G. Bartlett; B. J. Bauman; S. Beaumont; A. C. Becker; J. Becla; C. Beldica; S. Bellavia; G. Blanc; R. D. Blandford; J. S. Bloom; J. Bogart; K. Borne; J. F. Bosch; D. Boutigny; W. N. Brandt; M. E. Brown; J. S. Bullock; P. Burchat; D. L. Burke; G. Cagnoli; D. Calabrese; S. Chandrasekharan; S. Chesley; E. C. Cheu; J. Chiang; C. F. Claver; A. J. Connolly; K. H. Cook; A. Cooray; K. R. Covey; C. Cribbs; W. Cui; R. Cutri; G. Daubard; G. Daues; F. Delgado; S. Digel; P. Doherty; R. Dubois; G. P. Dubois-Felsmann; J. Durech; M. Eracleous; H. Ferguson; J. Frank; M. Freemon; E. Gangler; E. Gawiser; J. C. Geary; P. Gee; M. Geha; R. R. Gibson; D. K. Gilmore; T. Glanzman; I. Goodenow; W. J. Gressler; P. Gris; A. Guyonnet; P. A. Hascall; J. Haupt; F. Hernandez; C. Hogan; D. Huang; M. E. Huffer; W. R. Innes; S. H. Jacoby; B. Jain; J. Jee; J. G. Jernigan; D. Jevremovic; K. Johns; R. L. Jones; C. Juramy-Gilles; M. Juric; S. M. Kahn; J. S. Kalirai; N. Kallivayalil; B. Kalmbach; J. P. Kantor; M. M. Kasliwal; R. Kessler; D. Kirkby; L. Knox; I. Kotov; V. L. Krabbendam; S. Krughoff; P. Kubanek; J. Kuczewski; S. Kulkarni; R. Lambert; L. Le Guillou; D. Levine; M. Liang; K-T. Lim; C. Lintott; R. H. Lupton; A. Mahabal; P. Marshall; S. Marshall; M. May; R. McKercher; M. Migliore; M. Miller; D. J. Mills; D. G. Monet; M. Moniez; D. R. Neill; J-Y. Nief; A. Nomerotski; M. Nordby; P. O'Connor; J. Oliver; S. S. Olivier; K. Olsen; S. Ortiz; R. E. Owen; R. Pain; J. R. Peterson; C. E. Petry; F. Pierfederici; S. Pietrowicz; R. Pike; P. A. Pinto; R. Plante; S. Plate; P. A. Price; M. Prouza; V. Radeka; J. Rajagopal; A. Rasmussen; N. Regnault; S. T. Ridgway; S. Ritz; W. Rosing; C. Roucelle; M. R. Rumore; S. Russo; A. Saha; B. Sassolas; T. L. Schalk; R. H. Schindler; D. P. Schneider; G. Schumacher; J. Sebag; G. H. Sembroski; L. G. Seppala; I. Shipsey; N. Silvestri; J. A. Smith; R. C. Smith; M. A. Strauss; C. W. Stubbs; D. Sweeney; A. Szalay; P. Takacs; J. J. Thaler; R. Van Berg; D. Vanden Berk; K. Vetter; F. Virieux; B. Xin; L. Walkowicz; C. W. Walter; D. L. Wang; M. Warner; B. Willman; D. Wittman; S. C. Wolff; W. M. Wood-Vasey; P. Yoachim; H. Zhan; for the LSST Collaboration

    2014-08-29T23:59:59.000Z

    (Abridged) We describe here the most ambitious survey currently planned in the optical, the Large Synoptic Survey Telescope (LSST). A vast array of science will be enabled by a single wide-deep-fast sky survey, and LSST will have unique survey capability in the faint time domain. The LSST design is driven by four main science themes: probing dark energy and dark matter, taking an inventory of the Solar System, exploring the transient optical sky, and mapping the Milky Way. LSST will be a wide-field ground-based system designed to obtain multiple images covering the sky visible from Cerro Pach\\'{o}n in northern Chile. The telescope will have an 8.4 m (6.5 m effective) primary mirror, a 9.6 deg$^2$ field of view, and a 3.2 Gigapixel camera. This system can image about 10,000 square degrees of sky in three clear nights using pairs of 15-second exposures twice per night, with typical 5$\\sigma$ depth for point sources of $r\\sim24.5$ (AB). The project is in the construction phase and will begin regular survey operations by 2022. The survey area will be contained within 30,000 deg$^2$ with $\\delta<+34.5^\\circ$, and will be imaged multiple times in six bands, $ugrizy$, covering the wavelength range 320--1050 nm. About 90\\% of the observing time will be devoted to a deep-wide-fast survey mode which will uniformly observe a 18,000 deg$^2$ region about 800 times (summed over all six bands) during the anticipated 10 years of operations, and yield a coadded map to $r\\sim27.5$. The remaining 10\\% of the observing time will be allocated to projects such as a Very Deep and Fast time domain survey. The goal is to make LSST data products, including a relational database of about 32 trillion observations of 40 billion objects, available to the public and scientists around the world.

  11. Pharmaceutical R&D : an organizational design approach to enhancing productivity

    E-Print Network [OSTI]

    Adeusi, Sunny O. (Sunday Oluwasogo)

    2011-01-01T23:59:59.000Z

    The pharmaceutical industry is an $837 billion a year industry that is being plagued by low R&D productivity. This decline in productivity has resulted in significant erosion of value. From December 2000 to February 2008, ...

  12. Advanced turbine systems program conceptual design and product development. Quarterly report, February 1995--April 1995

    SciTech Connect (OSTI)

    NONE

    1995-06-01T23:59:59.000Z

    Research continued on the design of advanced turbine systems. This report describes the design and test of critical components such as blades, materials, cooling, combustion, and optical diagnostics probes.

  13. Socio-cognitive analysis of engineering systems design : shared knowledge, process, and product

    E-Print Network [OSTI]

    Avnet, Mark Sean

    2009-01-01T23:59:59.000Z

    This research is based on the well-known but seldom stated premise that the design of complex engineered systems is done by people -- each with their own knowledge, thoughts, and views about the system being designed. To ...

  14. Advanced turbine systems program -- Conceptual design and product development. Final report

    SciTech Connect (OSTI)

    NONE

    1996-07-26T23:59:59.000Z

    This Final Technical Report presents the accomplishments on Phase 2 of the Advanced Turbine Systems (ATS). The ATS is an advanced, natural gas fired gas turbine system that will represent a major advance on currently available industrial gas turbines in the size range of 1--20 MW. This report covers a market-driven development. The Market Survey reported in Section 5 identified the customer`s performance needs. This market survey used analyses performed by Solar turbine Incorporated backed up by the analyses done by two consultants, Research Decision Consultants (RDC) and Onsite Energy Corporation (Onsite). This back-up was important because it is the belief of all parties that growth of the ATS will depend both on continued participation in Solar`s traditional oil and gas market but to a major extent on a new market. This new market is distributed electrical power generation. Difficult decisions have had to be made to meet the different demands of the two markets. Available resources, reasonable development schedules, avoidance of schedule or technology failures, probable acceptance by the marketplace, plus product cost, performance and environmental friendliness are a few of the complex factors influencing the selection of the Gas Fired Advanced Turbine System described in Section 3. Section 4 entitled ``Conversion to Coal`` was a task which addresses the possibility of a future interruption to an economic supply of natural gas. System definition and analysis is covered in Section 6. Two major objectives were met by this work. The first was identification of those critical technologies that can support overall attainment of the program goals. Separate technology or component programs were begun to identify and parameterize these technologies and are described in Section 7. The second objective was to prepare parametric analyses to assess performance sensitivity to operating variables and to select design approaches to meet the overall program goals.

  15. Economic Analysis of the Reference Design for a Nuclear-Driven High-Temperature-Electrolysis Hydrogen Production Plant

    SciTech Connect (OSTI)

    E. A. Harvego; M. G. McKellar; M. S. Sohal; J. E. O'Brien; J. S. Herring

    2008-01-01T23:59:59.000Z

    A reference design for a commercial-scale high-temperature electrolysis (HTE) plant for hydrogen production was developed to provide a basis for comparing the HTE concept with other hydrogen production concepts. The reference plant design is driven by a high-temperature helium-cooled reactor coupled to a direct Brayton power cycle. The reference design reactor power is 600 MWt, with a primary system pressure of 7.0 MPa, and reactor inlet and outlet fluid temperatures of 540°C and 900°C, respectively. The electrolysis unit used to produce hydrogen consists of 4,009,177 cells with a per-cell active area of 225 cm2. A nominal cell area-specific resistance, ASR, value of 0.4 Ohm•cm2 with a current density of 0.25 A/cm2 was used, and isothermal boundary conditions were assumed. The optimized design for the reference hydrogen production plant operates at a system pressure of 5.0 MPa, and utilizes an air-sweep system to remove the excess oxygen that is evolved on the anode side of the electrolyzer. The inlet air for the air-sweep system is compressed to the system operating pressure of 5.0 MPa in a four-stage compressor with intercooling. The alternating current, AC, to direct current, DC, conversion is 96%. The overall system thermal-to-hydrogen production efficiency (based on the low heating value of the produced hydrogen) is 47.12% at a hydrogen production rate of 2.356 kg/s. An economic analysis of the plant was also performed using the H2A Analysis Methodology developed by the Department of Energy (DOE) Hydrogen Program. The results of the economic analysis demonstrated that the HTE hydrogen production plant driven by a high-temperature helium-cooled nuclear power plant can deliver hydrogen at a competitive cost using realistic financial and cost estimating assumptions. A required cost of $3.23 per kg of hydrogen produced was calculated assuming an internal rate of return of 10%. Approximately 73% of this cost ($2.36/kg) is the result of capital costs associated with the construction of the combined nuclear plant and hydrogen production facility. Operation and maintenance costs represent about 18% of the total cost ($0.57/kg). Variable costs (including the cost of nuclear fuel) contribute about 8.7% ($0.28/kg) to the total cost of hydrogen production, and decommissioning and raw material costs make up the remaining fractional cost.

  16. Decomposition Based Solution Approaches for Multi-product Closed-Loop Supply Chain Network Design Models

    E-Print Network [OSTI]

    Easwaran, Gopalakrishnan

    2010-01-16T23:59:59.000Z

    .1. Solution Representation . . . . . . . . . . . . . . . 61 viii CHAPTER Page IV.2.2. Objective Function Evaluation . . . . . . . . . . . 61 IV.2.3. Construction Heuristics . . . . . . . . . . . . . . . 65 IV.2.4. Neighborhood Functions.... For the sake of clarity in model development and analysis, we refer to the parts as products in the remainder of this document. Also, a supply location that provides new products is referred to as a new product plant (NPP), a supply location where...

  17. Design Concepts for Co-Production of Power, Fuels & Chemicals Via Coal/Biomass Mixtures

    SciTech Connect (OSTI)

    Rao, A. D.; Chen, Q.; Samuelsen, G. S.

    2012-09-30T23:59:59.000Z

    The overall goal of the program is to develop design concepts, incorporating advanced technologies in areas such as oxygen production, feed systems, gas cleanup, component separations and gas turbines, for integrated and economically viable coal and biomass fed gasification facilities equipped with carbon capture and storage for the following scenarios: (i) coproduction of power along with hydrogen, (ii) coproduction of power along with fuels, (iii) coproduction of power along with petrochemicals, and (iv) coproduction of power along with agricultural chemicals. To achieve this goal, specifically the following objectives are met in this proposed project: (i) identify advanced technology options and innovative preliminary design concepts that synergistically integrate plant subsections, (ii) develop steady state system simulations to predict plant efficiency and environmental signature, (iii) develop plant cost estimates by capacity factoring major subsystems or by major equipment items where required, and then capital, operating and maintenance cost estimates, and (iv) perform techno- economic analyses for the above described coproduction facilities. Thermal efficiencies for the electricity only cases with 90% carbon capture are 38.26% and 36.76% (HHV basis) with the bituminous and the lignite feedstocks respectively. For the coproduction cases (where 50% of the energy exported is in the form of electricity), the electrical efficiency, as expected, is highest for the hydrogen coproduction cases while lowest for the higher alcohols (ethanol) coproduction cases. The electrical efficiencies for Fischer-Tropsch coproduction cases are slightly higher than those for the methanol coproduction cases but it should be noted that the methanol (as well as the higher alcohol) coproduction cases produce the finished coproduct while the Fischer-Tropsch coproduction cases produce a coproduct that requires further processing in a refinery. The cross comparison of the thermal performance between the various coproduct cases is further complicated by the fact that the carbon footprint is not the same when carbon leaving with the coproduct are accounted for. The economic analysis and demand for a particular coproduct in the market place is a more meaningful comparison of the various coproduction scenarios. The first year cost of electricity calculated for the bituminous coal is $102.9/MWh while that for the lignite is $108.1/MWh. The calculated cost of hydrogen ranged from $1.42/kg to $2.77/kg depending on the feedstock, which is lower than the DOE announced hydrogen cost goal of $3.00/kg in July 14, 2005. Methanol cost ranged from $345/MT to $617/MT, while the market price is around $450/MT. For Fischer-Tropsch liquids, the calculated cost ranged from $65/bbl to $112/bbl, which is comparable to the current market price of crude oil at around $100/bbl. It should be noted, however, that F-T liquids contain no sulfur and nitrogen compounds. The calculated cost of alcohol ranged from $4.37/gal to $5.43/gal, while it ranged from $2.20/gal to $3.70/gal in a DOE funded study conducted by Louisiana State University. The Louisiana State University study consisted of a significantly larger plant than our study and benefited from economies of scale. When the plant size in our study is scaled up to similar size as in the Louisiana State University study, cost of alcohol is then reduced to a range of $3.24/gal to $4.28/gal, which is comparable. Urea cost ranged from $307/MT to $428/MT, while the market price is around $480/MT.

  18. Covered Product Category: Air-Cooled Ice Machines

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for air-cooled ice machines, which are covered by the ENERGY STAR program.

  19. PRODUCTION TPBAR INPUTS FOR CORE DESIGNERS TTQP-1-116 Rev 15

    SciTech Connect (OSTI)

    Collins, Brian A.; Love, Edward F.; Thornhill, Cheryl K.

    2012-11-01T23:59:59.000Z

    The purpose of this controlled document is to provide a convenient reference for tritiumproducing burnable absorber rod (TPBAR) parameters used by reactor core designers.

  20. DESIGN AND DEVELOPMENT OF COST EFFECTIVE SURFACE MOUNTED WATER TURBINES FOR RURAL ELECTRICITY PRODUCTION

    E-Print Network [OSTI]

    Sóbester, András

    for further hydro development. Optimization of existing recourses for power harnessing has made application/low head hydro power generation. This project intends to design and develop cost effective design of engineered low head hydro turbines capable of utilizing 2-10 meter of water head and power output 2 to 15 k

  1. Masters Thesis- Criticality Alarm System Design Guide with Accompanying Alarm System Development for the Radioisotope Production Laboratory in Richland, Washington

    SciTech Connect (OSTI)

    Greenfield, Bryce A.

    2009-12-20T23:59:59.000Z

    A detailed instructional manual was created to guide criticality safety engineers through the process of designing a criticality alarm system (CAS) for Department of Energy (DOE) hazard class 1 and 2 facilities. Regulatory and technical requirements were both addressed. A list of design tasks and technical subtasks are thoroughly analyzed to provide concise direction for how to complete the analysis. An example of the application of the design methodology, the Criticality Alarm System developed for the Radioisotope Production Laboratory (RPL) of Richland, Washington is also included. The analysis for RPL utilizes the Monte Carlo code MCNP5 for establishing detector coverage in the facility. Significant improvements to the existing CAS were made that increase the reliability, transparency, and coverage of the system.

  2. FEMP O&M Program

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    - Cost information, efficiency information, and URL links updated - Additional graphics, charts, and tables added to motivate reader to create near-term action plan -...

  3. Design of generic coal conversion facilities: Production of oxygenates from synthesis gas---A technology review

    SciTech Connect (OSTI)

    Not Available

    1991-10-01T23:59:59.000Z

    This report concentrates on the production of oxygenates from coal via gasification and indirect liquefaction. At the present the majority of oxygenate synthesis programs are at laboratory scale. Exceptions include commercial and demonstration scale plants for methanol and higher alcohols production, and ethers such as MTBE. Research and development work has concentrated on elucidating the fundamental transport and kinetic limitations governing various reactor configurations. But of equal or greater importance has been investigations into the optimal catalyst composition and process conditions for the production of various oxygenates.

  4. Advanced Turbine Systems Program conceptual design and product development. Annual report, August 1993--July 1994

    SciTech Connect (OSTI)

    Not Available

    1994-11-01T23:59:59.000Z

    The stated objective of the project was to analyze and evaluate different cycles for the natural gas-fired Advanced Turbine Systems (GFATS) in order to select one that would achieve all of the ATS Program goals. Detailed cycle performance, cost of electricity, and RAM analysis were carried out to provide information on the final selection of the GFATS cycle. To achieve the very challenging goals, innovative approaches and technological advances are required, especially in combustion, aerodynamic design, cooling design, mechanical design, leakage control, materials, and coating technologies.

  5. The design and manufacture of mass production equipment for a pencil with a seed

    E-Print Network [OSTI]

    Del Castillo, Eric A. (Eric Anthony)

    2013-01-01T23:59:59.000Z

    Autosprout is the mass manufacturing equipment envisioned to produce Sprout, a pencil with a seed. This pencil concept was developed by MIT students a successful round of funding and first production run through Kickstarter. ...

  6. Modifying organization design and development process to mitigate project delay in microprocessor product development

    E-Print Network [OSTI]

    Hou, Tianlue

    2007-01-01T23:59:59.000Z

    In today's engineering project management, there is no lack of strategies to plan and assign task items to reduce the overall project timeline. However, as the product gets more complicated and organization gets much larger, ...

  7. From Product End-of-Life Sustainable Considerations to Design Management

    E-Print Network [OSTI]

    Boyer, Edmond

    in terms of Greenhouse Gas (GHG) emissions, for instance, the world sources institute reported in 2005: reuse, recycle, remanufacture or dispose (landfill or incineration) and their impact during product

  8. Product line-up design based on preference measurement : a case study on TV industry

    E-Print Network [OSTI]

    Park, Chang Bae, S.M. Massachusetts Institute of Technology

    2011-01-01T23:59:59.000Z

    Sony, in 2010, introduced innovative product line-up setting process for its TV, using the technique of market segmentation and conjoint analysis. This practice was expected to increase its sales compared to traditional ...

  9. Analysis of the product development process for geographically distant teams in vehicle tophat design phases

    E-Print Network [OSTI]

    Puerto Valdez, Antonio del

    2010-01-01T23:59:59.000Z

    The current global economic recession is putting pressure to increase model variation on the car makers, while at the same time leveraging highly efficient and proven platforms and product development assets globally is ...

  10. A Systematic Approach for the Design of Integrated Energy and Chemicals Production 

    E-Print Network [OSTI]

    Noureldin, Mohamed Mahmoud

    2014-12-02T23:59:59.000Z

    on CO2 and H2O production, energy input and carbon deposition in dry reforming (P = 1 bar) ............................................ 36 Figure 12: Impact of CO2 sequestration on the maximum economic potential for hydrogen production... (P = 1 bar) ........................................................................................................ 29 Figure 5: Effect of CH4:H2O ratio on CO2 and H2O generation, energy input and carbon deposition in SR (P = 1 bar...

  11. A Systematic Approach for the Design of Integrated Energy and Chemicals Production

    E-Print Network [OSTI]

    Noureldin, Mohamed Mahmoud

    2014-12-02T23:59:59.000Z

    on CO2 and H2O production, energy input and carbon deposition in dry reforming (P = 1 bar) ............................................ 36 Figure 12: Impact of CO2 sequestration on the maximum economic potential for hydrogen production... (P = 1 bar) ........................................................................................................ 29 Figure 5: Effect of CH4:H2O ratio on CO2 and H2O generation, energy input and carbon deposition in SR (P = 1 bar...

  12. Advanced turbine systems program--conceptual design and product development. Quarterly report, November 1994--January 1995

    SciTech Connect (OSTI)

    NONE

    1995-02-01T23:59:59.000Z

    Research continued in the design and development of advanced gas turbine systems. This report presents progress towards turbine blade development, diffuser development, combustion noise investigations,catalytic combustion development, and diagnostic probe development.

  13. Design Of Heat-Activated Reversible Integral Attachments For Product-Embedded Disassembly

    E-Print Network [OSTI]

    Saitou, Kazuhiro "Kazu"

    }@engin.umich.edu Abstract Disassembly is a fundamental process needed for component reuse and material recycling in all some snap-fits are designed to be reverisble (eg., battery covers for cellular phones), they require

  14. Impact of prototyping resource environments on idea generation in product design

    E-Print Network [OSTI]

    Schlecht, Lisa (Lisa Anne)

    2013-01-01T23:59:59.000Z

    Some of the world's most challenging problems will require distributed innovation capacity in order to create high-quality and sustainable solutions. However, access to prototyping resources varies and design strategies ...

  15. Man-portable power generation devices : product design and supporting algorithms

    E-Print Network [OSTI]

    Mitsos, Alexander

    2006-01-01T23:59:59.000Z

    A methodology for the optimal design and operation of microfabricated fuel cell systems is proposed and algorithms for relevant optimization problems are developed. The methodology relies on modeling, simulation and ...

  16. Product design and development of an aerodynamic hydration system for bicycling and triathlon

    E-Print Network [OSTI]

    Cote, Mark (Mark Brian)

    2007-01-01T23:59:59.000Z

    Proper hydration and aerodynamic performance are both essential needs of a competitive cyclist or triathlete. Several aerodynamic systems have been developed for use on bicycles but few have been designed to be truly ...

  17. Production

    Broader source: Energy.gov [DOE]

    Algae production R&D focuses on exploring resource use and availability, algal biomass development and improvements, characterizing algal biomass components, and the ecology and engineering of...

  18. Maintaining a Technology-Neutral Approach to Hydrogen Production Process Development through Conceptual Design of the Next Generation Nuclear Plant

    SciTech Connect (OSTI)

    Michael W. Patterson

    2008-05-01T23:59:59.000Z

    The Next Generation Nuclear Plant (NGNP) project was authorized in the Energy Policy Act of 2005 (EPAct), tasking the U.S. Department of Energy (DOE) with demonstrating High Temperature Gas-Cooled Reactor (HTGR) technology. The demonstration is to include the technical, licensing, operational, and commercial viability of HTGR technology for the production of electricity and hydrogen. The Nuclear Hydrogen Initiative (NHI), a component of the DOE Hydrogen Program managed by the Office of Nuclear Energy, is also investigating multiple approaches to cost effective hydrogen production from nuclear energy. The objective of NHI is development of the technology and information basis for a future decision on commercial viability. The initiatives are clearly intertwined. While the objectives of NGNP and NHI are generally consistent, NGNP has progressed to the project definition phase and the project plan has matured. Multiple process applications for the NGNP require process heat, electricity and hydrogen in varied combinations and sizes. Coupling these processes to the reactor in multiple configurations adds complexity to the design, licensing and demonstration of both the reactor and the hydrogen production process. Commercial viability of hydrogen production may depend on the specific application and heat transport configuration. A component test facility (CTF) is planned by the NGNP to support testing and demonstration of NGNP systems, including those for hydrogen production, in multiple configurations. Engineering-scale demonstrations in the CTF are expected to start in 2012 to support scheduled design and licensing activities leading to subsequent construction and operation. Engineering-scale demonstrations planned by NHI are expected to start at least two years later. Reconciliation of these schedules is recommended to successfully complete both initiatives. Hence, closer and earlier integration of hydrogen process development and heat transport systems is sensible. For integration purposes, an analysis comparing the design, cost and schedule impact of maintaining a technology neutral approach through conceptual design or making an early hydrogen process technology selection was performed. Early selection does not specifically eliminate a technology, but rather selects the first hydrogen technology for demonstration. A systems-engineering approach was taken to define decision-making criteria for selecting a hydrogen technology. The relative technical, cost and schedule risks of each approach were analyzed and risk mitigation strategies were recommended, including provisions to maintain close collaboration with the NHI. The results of these analyses are presented here.

  19. Chemical enterprise model and decision-making framework for sustainable chemical product design

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    for complying with regulations, like REACH in Europe. Initially devoted to chemists, chemicals substitution are reconsidering the products that they use and produce, under the pressure of regulations like REACH [1] and VOC: the use of renewable materials, the minimization of energy and material resources consumption

  20. FOR COMPANIES THAT design electromechani-cal products, staying competitive in today's global

    E-Print Network [OSTI]

    -resource-planning systems. In light of this, new data interfaces and associated data exchange methodologies had few years, system vendors started to develop an entirely new generation of CAE soft- ware applications market means using systems that unify the de- sign process, and allow the smooth flow of design data

  1. METHOD AND TOOLS TO MEET ENERGY EFFICIENCY TARGETS AT PRODUCT DESIGN STAGE

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    are energy indicator, guidelines and an environmental checking loop. The following paper is focused its design. · Guidelines tool: provides guidelines to fill the gap between energy consumption assessed is an instantaneous value, easy to measure with simple protocols. Taking into account the time dimension needs more

  2. Classification and grading of design products for the Yucca Mountain project

    SciTech Connect (OSTI)

    DeKlever, R.C.; Bullock, R.L. [Raytheon Services Nevada, Las Vegas (United States); Verna, B.J. [Department of Energy, Washington, DC (United States)

    1993-12-01T23:59:59.000Z

    The US Department of Energy faces some unique challenges in its site characterization effort to determine if Yucca Mountain is suitable to house this nation`s first high-level radioactive waste repository. Facilities are being designed and constructed for both surface-based testing (SBT), which includes drilling a number of test holes and excavating trenches and test pits into the mountain, and the Exploratory Studies Facility (ESF), which will be an extensive underground test laboratory. During construction and testing, the Yucca Mountain Project (YMP) must ensure that the ability to safely store waste for 10,000 yr is not compromised. The YMP has initiated a determination of {open_quotes}important to waste isolation{close_quotes} (ITWI) effort to determine which items and activities are important to the gathering of valid test data and which could have an effect on the natural barriers. Concerns include the potential effects of changing the site`s normal water patterns, introducing foreign materials, damaging the unexcavated rock, etc. The project has now entered into the phase in which the design organizations perform detailed QA classification analyses on their designs and a YMP assessment team reviews those analyses. Raytheon Services Nevada has been responsible for designing, classifying, and grading SBT and the initial ESF systems.

  3. MODEL BASED BIOMASS SYSTEM DESIGN OF FEEDSTOCK SUPPLY SYSTEMS FOR BIOENERGY PRODUCTION

    SciTech Connect (OSTI)

    David J. Muth, Jr.; Jacob J. Jacobson; Kenneth M. Bryden

    2013-08-01T23:59:59.000Z

    Engineering feedstock supply systems that deliver affordable, high-quality biomass remains a challenge for the emerging bioenergy industry. Cellulosic biomass is geographically distributed and has diverse physical and chemical properties. Because of this feedstock supply systems that deliver cellulosic biomass resources to biorefineries require integration of a broad set of engineered unit operations. These unit operations include harvest and collection, storage, preprocessing, and transportation processes. Design decisions for each feedstock supply system unit operation impact the engineering design and performance of the other system elements. These interdependencies are further complicated by spatial and temporal variances such as climate conditions and biomass characteristics. This paper develops an integrated model that couples a SQL-based data management engine and systems dynamics models to design and evaluate biomass feedstock supply systems. The integrated model, called the Biomass Logistics Model (BLM), includes a suite of databases that provide 1) engineering performance data for hundreds of equipment systems, 2) spatially explicit labor cost datasets, and 3) local tax and regulation data. The BLM analytic engine is built in the systems dynamics software package PowersimTM. The BLM is designed to work with thermochemical and biochemical based biofuel conversion platforms and accommodates a range of cellulosic biomass types (i.e., herbaceous residues, short- rotation woody and herbaceous energy crops, woody residues, algae, etc.). The BLM simulates the flow of biomass through the entire supply chain, tracking changes in feedstock characteristics (i.e., moisture content, dry matter, ash content, and dry bulk density) as influenced by the various operations in the supply chain. By accounting for all of the equipment that comes into contact with biomass from the point of harvest to the throat of the conversion facility and the change in characteristics, the BLM evaluates economic performance of the engineered system, as well as determining energy consumption and green house gas performance of the design. This paper presents a BLM case study delivering corn stover to produce cellulosic ethanol. The case study utilizes the BLM to model the performance of several feedstock supply system designs. The case study also explores the impact of temporal variations in climate conditions to test the sensitivity of the engineering designs. Results from the case study show that under certain conditions corn stover can be delivered to the cellulosic ethanol biorefinery for $35/dry ton.

  4. Production

    Broader source: Energy.gov [DOE]

    Algae production R&D focuses on exploring resource use and availability, algal biomass development and improvements, characterizing algal biomass components, and the ecology and engineering of cultivation systems.

  5. The use of daylight in the design of a controlled environment for food production in the Caribbean and other equatorial climates

    E-Print Network [OSTI]

    Charles, Curtis B

    1989-01-01T23:59:59.000Z

    This thesis addresses the use of daylight in the design of a controlled environment for food production in the Caribbean and other Equatorial climates. An expanding population has put a tremendous burden on the food ...

  6. Simulating intertwined design processes that have similar structures: a case study of a small company that creates made-to-order fashion products

    E-Print Network [OSTI]

    Wynn, David C; Eckert, Claudia M; Clarkson, P John

    The authors use simulation to analyse the resource-driven dependencies between concurrent processes used to create customised products in a company. Such processes are uncertain and unique according to the design changes required. However, they have...

  7. MDP-8 Cairo University Conference Proceeding of MDP-8, Cairo University Conference on Mechanical Design and Production Cairo, Egypt, January 4-6, 2004

    E-Print Network [OSTI]

    Saitou, Kazuhiro "Kazu"

    Design and Production Cairo, Egypt, January 4-6, 2004 77 TOPOLOGY OPTIMIZATION OF STRUCTURAL SUPPORTS, Egypt, January 4-6, 2004 Shalaby and Saitou 78 This paper proposes a solution to prevent the buckling

  8. Review of fission product retention experiment results and application to the LWR design

    SciTech Connect (OSTI)

    Lischer, D.J.; Elia, F.A. Jr. (Stone and Webster Engineering Corp., Boston, MA (United States))

    1992-01-01T23:59:59.000Z

    This paper examines the available literature on pipe retention of aerosols to determine the feasiblity of taking credit for attenuation of radioactive release from the plant through pipes when calculating off-site dose rates for plant licensing and emergency planning considerations. The results show that deposition in pipes can be significant. Experimental work on aerosol plugging shows that this phenomenon may provide the dominant mechanism for fission product retention.

  9. Esthetically Designed Municipal PV System Maximizes Energy Production and Revenue Return

    Broader source: Energy.gov [DOE]

    In late 2008, the City of Sebastopol, CA installed a unique 42 kW grid-interactive photovoltaic (PV) system to provide electricity for pumps of the Sebastopol municipal water system. The resulting innovative Sun Dragon PV system, located in a public park, includes design elements that provide optimized electrical performance and revenue generation for the energy produced while also presenting an artistic and unique appearance to park visitors.

  10. Advanced turbine systems program conceptual design and product development. Quarterly report, August--October 1995

    SciTech Connect (OSTI)

    NONE

    1996-01-01T23:59:59.000Z

    This report describes the tasks completed for the advanced turbine systems program. The topics of the report include last row turbine blade development, single crystal blade casting development, ceramic materials development, combustion cylinder flow mapping, shroud film cooling, directional solidified valve development, shrouded blade cooling, closed-loop steam cooling, active tip clearance control, flow visualization tests, combustion noise investigation, TBC field testing, catalytic combustion development, optical diagnostics probe development, serpentine channel cooling tests, brush seal development, high efficiency compressor design, advanced air sealing development, advanced coating development, single crystal blade development, Ni-based disc forging development, and steam cooling effects on materials.

  11. Conceptual design of the Mu2e production solenoid cold mass

    SciTech Connect (OSTI)

    Kashikhin, V.V.; Ambrosio, G.; Andreev, N.; Lamm, M.; Mokhov, N.V.; Nicol, T.H.; Page, T.M.; Pronskikh, V.; /Fermilab

    2011-06-01T23:59:59.000Z

    The Muon-to-Electron conversion experiment (Mu2e), under development at Fermilab, seeks to detect direct muon to electron conversion to provide evidence for a process violating muon and electron lepton number conservation that cannot be explained by the Standard Model of particle physics. The required magnetic field is produced by a series of superconducting solenoids of various apertures and lengths. This paper describes the conceptual design of the 5 T, 4 m long solenoid cold mass with 1.67 m bore with the emphasis on the magnetic, radiation and thermal analyses.

  12. Design and construction of a cottonseed huller for use in food products

    E-Print Network [OSTI]

    Bell, Lynn Eric

    1973-01-01T23:59:59.000Z

    . Mechanical Shearing The shearing process was extensively researched and evaluated. The small scale hulling device that was used was a rice sample sheller (Fig. 2) designed and fabricated by the H. T. McGill Com- pany [6] . Seed in this device were gravity... between the rollers was adjustable in in- crements of . 001 in. Tests were performed to determine the hull- ing capability of the machine and were evaluated on the basis of percent of the input seed hulled and the size of the kernel par- ticles...

  13. DESIGN OF A SUBCRITICAL AQUEOUS TARGET SYSTEM FOR MEDICAL ISOTOPE PRODUCTION 

    E-Print Network [OSTI]

    Vega, Richard Manuel

    2013-12-10T23:59:59.000Z

    , SUPO, LAPRE-1, and LAPRE-2. LOPO was a low power reactor which utilized uranyl sulfate fuel, while HYPO and SUPO had higher power outputs and utilized uranyl nitrate fuel. LAPRE-1 and LAPRE-2 utilized uranium oxide mixed in high concentration... to corrosion such as zirconium and titanium alloys. Zircaloy-4 in par- ticular has been shown to have a corrosion rate of less than 0.1 mm per year when in contact with uranyl sulfate at 250 °C. [14] Recent designs have limited the corrosion by limiting...

  14. Design Case Summary: Production of Gasoline and Diesel from Biomass via

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube| DepartmentStatementDepartment ofVisits KazakhstanSummit -Design &

  15. Design Case Summary: Production of Mixed Alcohols from Municipal Solid Waste via Gasification

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube| DepartmentStatementDepartment ofVisits KazakhstanSummit -Design &Mixed

  16. Designing catalysts for hydrogen production | Center for Bio-Inspired Solar

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration wouldDECOMPOSITIONPortalToDepthand ImmobilizationDesignerFuel

  17. Design manual for management of solid by-products from advanced coal technologies

    SciTech Connect (OSTI)

    NONE

    1994-10-01T23:59:59.000Z

    Developing coal conversion technologies face major obstacles in byproduct management. This project has developed several management strategies based on field trials of small-scale landfills in an earlier phase of the project, as well as on published/unpublished sources detailing regulatory issues, current industry practice, and reuse opportunities. Field testing, which forms the basis for several of the disposal alternatives presented in this design manual, was limited to byproducts from Ca-based dry SO{sub 2} control technologies, circulating fluidized bed combustion ash, and bubbling bed fluidized bed combustion ash. Data on byproducts from other advanced coal technologies and on reuse opportunities are drawn from other sources (citations following Chapter 3). Field results from the 5 test cases examined under this project, together with results from other ongoing research, provide a basis for predictive modeling of long-term performance of some advanced coal byproducts on exposure to ambient environment. This manual is intended to provide a reference database and development plan for designing, permitting, and operating facilities where advanced coal technology byproducts are managed.

  18. Laboratories for the 21st Century: An Introduction to Low-Energy Design (Revised)

    SciTech Connect (OSTI)

    Not Available

    2008-08-01T23:59:59.000Z

    This booklet is an introduction to several new strategies for designing, developing, and retrofitting energy-efficient laboratories. It is the result of a collaboration among staff at the U.S. Environmental Protection Agency (EPA), the U.S. Department of Energy's (DOE's) Federal Energy Management Program (FEMP), several national laboratories, and their contractors. They are collaborating to meet the goals of a joint EPA-DOE initiative, 'Laboratories for the 21st Century,' which was established to help government and private-sector laboratory designers, engineers, owners, and operators work together to increase operating efficiency and reduce costs. This booklet describes many energy-efficient strategies that can be done during laboratory planning and programming; design; engineering; and commissioning, operation, and maintenance. There is also a discussion of on-site power generation and clean sources of electricity from renewable energy.

  19. Advanced Turbine Systems program conceptual design and product development. Quarterly report, February--April 1994

    SciTech Connect (OSTI)

    NONE

    1995-02-01T23:59:59.000Z

    Task 8.5 (active clearance control) was replaced with a test of the 2600F prototype turbine (Task 8.1T). Test 8.1B (Build/Teardown of prototype turbine) was added. Tasks 4 (conversion of gas-fired turbine to coal-fired turbine) and 5 (market study) were kicked off in February. Task 6 (conceptual design) was also initiated. Task 8.1 (advanced cooling technology) now has an approved test plan. Task 8.4 (ultra low NOx combustion technology) has completed the code development and background gathering phase. Task 8.6 (two-phase cooling of turbine vanes) is proceeding well; initial estimates indicate that nearly 2/3 of required cooling flow can be eliminated.

  20. The economical production of alcohol fuels from coal-derived synthesis gas: Case studies, design, and economics

    SciTech Connect (OSTI)

    NONE

    1995-10-01T23:59:59.000Z

    This project is a combination of process simulation and catalyst development aimed at identifying the most economical method for converting coal to syngas to linear higher alcohols to be used as oxygenated fuel additives. There are two tasks. The goal of Task 1 is to discover, study, and evaluate novel heterogeneous catalytic systems for the production of oxygenated fuel enhancers from synthesis gas, and to explore, analytically and on the bench scale, novel reactor and process concepts for use in converting syngas to liquid fuel products. The goal of Task 2 is to simulate, by computer, energy efficient and economically efficient processes for converting coal to energy (fuel alcohols and/or power). The primary focus is to convert syngas to fuel alcohols. This report contains results from Task 2. The first step for Task 2 was to develop computer simulations of alternative coal to syngas to linear higher alcohol processes, to evaluate and compare the economics and energy efficiency of these alternative processes, and to make a preliminary determination as to the most attractive process configuration. A benefit of this approach is that simulations will be debugged and available for use when Task 1 results are available. Seven cases were developed using different gasifier technologies, different methods for altering the H{sub 2}/CO ratio of the syngas to the desired 1.1/1, and with the higher alcohol fuel additives as primary products and as by-products of a power generation facility. Texaco, Shell, and Lurgi gasifier designs were used to test gasifying coal. Steam reforming of natural gas, sour gas shift conversion, or pressure swing adsorption were used to alter the H{sub 2}/CO ratio of the syngas. In addition, a case using only natural gas was prepared to compare coal and natural gas as a source of syngas.

  1. Production of cooking briquettes from Maissade (Haiti) lignite. Feasibility study and preliminary plant design

    SciTech Connect (OSTI)

    Hauserman, W.B.; Johnson, M.D.

    1986-03-20T23:59:59.000Z

    A laboratory study was done to establish the technical feasibility of producing domestic cooking briquettes to be marketed in Haiti, from the Maissade lignite reserves of that country, which are high in both ash and sulfur and not yet mined. It was found that acceptable briquettes could be made from Maissade char, pyrolized and compacted with a molasses-lime binder and the addition of bagasse to improve strength and burning rate. Molasses, lime and bagasse are all produced in Haiti. Sodium nitrate was added to enhance ignition, and borax as a wetting and release agent. Standard, ''pillow-shaped'' briquettes were successfully produced on a standard, double roll briquetting machine. The recommended process sequence and equipment selection are virtually identical to that used to produce standard US barbecue briquettes from North Dakota lignite. The heating value of the Maissade briquettes is lower due to their high ash level, which may be acceptable if they can be produced at a cost per heating value comparable to wood charcoal, currently used in Haiti. The high sulfur content, mostly in organic form, presents no problem, since it is tied up after combustion as CaSO/sub 4/ by the unusually high calcium content of this lignite. Detailed analyses of Maissade lignite and its mineral components are included, as well as a preliminary plant design and capital cost estimate, for capacities of 10,000 and 50,000 metric tons per year, and for a smaller pilot plant.

  2. Advanced turbine systems program conceptual design and product development Task 8.3 - autothermal fuel reformer (ATR). Topical report

    SciTech Connect (OSTI)

    NONE

    1996-11-01T23:59:59.000Z

    Autothermal fuel reforming (ATR) consists of reacting a hydrocarbon fuel such as natural gas or diesel with steam to produce a hydrogen-rich {open_quotes}reformed{close_quotes} fuel. This work has been designed to investigate the fuel reformation and the product gas combustion under gas turbine conditions. The hydrogen-rich gas has a high flammability with a wide range of combustion stability. Being lighter and more reactive than methane, the hydrogen-rich gas mixes readily with air and can be burned at low fuel/air ratios producing inherently low emissions. The reformed fuel also has a low ignition temperature which makes low temperature catalytic combustion possible. ATR can be designed for use with a variety of alternative fuels including heavy crudes, biomass and coal-derived fuels. When the steam required for fuel reforming is raised by using energy from the gas turbine exhaust, cycle efficiency is improved because of the steam and fuel chemically recuperating. Reformation of natural gas or diesel fuels to a homogeneous hydrogen-rich fuel has been demonstrated. Performance tests on screening various reforming catalysts and operating conditions were conducted on a batch-tube reactor. Producing over 70 percent of hydrogen (on a dry basis) in the product stream was obtained using natural gas as a feedstock. Hydrogen concentration is seen to increase with temperature but less rapidly above 1300{degrees}F. The percent reforming increases as the steam to carbon ratio is increased. Two basic groups of reforming catalysts, nickel - and platinum-basis, have been tested for the reforming activity.

  3. Phase 1 --2

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    team, affected facilitybuilding managers, design, engineering, and constructionservice contract oversightinspection team (e.g. environmental, safety and health staff), FEMP...

  4. Estimating the upper limit of gas production from Class 2 hydrate accumulations in the permafrost: 2. Alternative well designs and sensitivity analysis

    SciTech Connect (OSTI)

    Moridis, G.; Reagan, M.T.

    2011-01-15T23:59:59.000Z

    In the second paper of this series, we evaluate two additional well designs for production from permafrost-associated (PA) hydrate deposits. Both designs are within the capabilities of conventional technology. We determine that large volumes of gas can be produced at high rates (several MMSCFD) for long times using either well design. The production approach involves initial fluid withdrawal from the water zone underneath the hydrate-bearing layer (HBL). The production process follows a cyclical pattern, with each cycle composed of two stages: a long stage (months to years) of increasing gas production and decreasing water production, and a short stage (days to weeks) that involves destruction of the secondary hydrate (mainly through warm water injection) that evolves during the first stage, and is followed by a reduction in the fluid withdrawal rate. A well configuration with completion throughout the HBL leads to high production rates, but also the creation of a secondary hydrate barrier around the well that needs to be destroyed regularly by water injection. However, a configuration that initially involves heating of the outer surface of the wellbore and later continuous injection of warm water at low rates (Case C) appears to deliver optimum performance over the period it takes for the exhaustion of the hydrate deposit. Using Case C as the standard, we determine that gas production from PA hydrate deposits increases with the fluid withdrawal rate, the initial hydrate saturation and temperature, and with the formation permeability.

  5. HYDROGEN INITIATIVE: AN INTEGRATED APPROACH TOWARD RATIONAL NANOCATALYST DESIGN FOR HYDROGEN PRODUCTION. Technical Report-Year 1

    SciTech Connect (OSTI)

    Vlachos, Dionisios G; Buttrey, Douglas J; Lauterbach, Jochen

    2007-03-29T23:59:59.000Z

    The overall objective of this grant is to develop a rational framework for the discovery of low cost, robust, and active nano-catalysts that will enable efficient hydrogen production. Our approach will be the first demonstration of integrated multiscale model, nano-catalyst synthesis, and nanoscale characterization assisted high throughput experimentation (HTE). We will initially demonstrate our approach with ammonia decomposition on noble metal catalysts. Our research focuses on many elements of the Hydrogen Initiative in the Focus Area of “Design of Catalysts at the Nanoscale’. It combines high-throughput screening methods with various nanostructure synthesis protocols, advanced measurements, novel in situ and ex situ characterization techniques, and multiscale theory, modeling and simulation. This project directly addresses several of the long-term goals of the DOE/BES program. In particular, new nanoscale catalytic materials will be synthesized, characterized and modeled for the production of hydrogen from ammonia and a computational framework will be developed for efficient extraction of information from experimental data and for rational design of catalysts whose impact goes well beyond the proposed hydrogen production project. In the first year of the grant, we have carried out HTE screening using a 16 parallel microreactor coupled with an FTIR analysis system. We screened nearly twenty single metals and several bimetallic catalysts as a function of temperature, catalyst loading, inlet composition, and temperature (order of 400 experiments). We have found that Ru is the best single metal catalyst and no better catalysts were found among the library of bimetallics we have created so far. Furthermore, we have investigated promoting effects (i.e., K, Cs, and Ba) of the Ru catalyst. We have found that K is the dominant promoter of increased Ru activity. Response surface experimental design has led to substantial improvements of the Ru catalyst with promotion, especially at lower temperatures. It has been found that the promoting effect is not limited to K but extendible to some other alkaline metals. In addition, we have studied a number of synthesis variables, including the effects of support, solvent used, calcination temperature and time. It has been found that solvent and support could have an important effect on activity. Advanced characterization of the Ru/K promoted catalyst has been carried via SEM, TEM, selected-area electron diffraction, and energy dispersive x-ray spectroscopy. It has been found that the Ru catalyst is composed of agglomerates, whereas the K-promoted catalyst of “nanowhiskers” with a KRu4O8 hollandite structure. Our detailed characterization studies strongly suggest for the first time a strong correlation between hollandite formation and the high activity of Ru catalyst. Future work should provide stronger evidence of this correlation and may enable us to further improve the catalyst. A number of microkinetic models for single metals have been developed and a methodology for linking models for bimetallic catalysts in a thermodynamically consistent manner has been implemented. This enables us for the first time to start exploring multi-site catalysts, using either mean-field or Monte Carlo approaches, and filling the materials gap from single crystals to supported catalysts. In addition, we are developing a multiscale model-based design of experiments methodology. This framework employs multiscale-based models combined with global search in experimental parameter space, identification of novel experimental conditions that maximize the kinetic information content, followed by statistical analysis that can guide the next iteration of experiments.

  6. 8/27/2014 Human Factors and Ergonomics Society: WhyAren't Product Designers Considering ActivityTrackers for Older Adults? https://www.hfes.org//Web/DetailNews.aspx?ID=340 1/2

    E-Print Network [OSTI]

    8/27/2014 Human Factors and Ergonomics Society: WhyAren't Product Designers Considering Activity benefits, product designers rarely consider those over 65 to be a viable user group, and new human factors/ergonomics and Ergonomics in Health Care in April, authors Preusse, Tracy Mitzner, Cara Fausset, and Wendy Rogers designed

  7. Nanotechnology for Solar-hydrogen Production via Photoelectrochemical Water-splitting: Design, Synthesis, Characterization, and Application of Nanomaterials and Quantum Dots 

    E-Print Network [OSTI]

    Alenzi, Naser D.

    2012-02-14T23:59:59.000Z

    NANOTECHNOLOGY FOR SOLAR-HYDROGEN PRODUCTION VIA PHOTOELECTROCHEMICAL WATER-SPLITTING: DESIGN, SYNTHESIS, CHARACTERIZATION, AND APPLICATION OF NANOMATERIALS AND QUANTUM DOTS A Dissertation by NASER D. ALENZI Submitted... to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY December 2010 Major Subject: Petroleum Engineering NANOTECHNOLOGY FOR SOLAR-HYDROGEN PRODUCTION VIA...

  8. American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance Federal Aviation Administration Project 209 - Control Tower and Support Building, Las Vegas, NV

    SciTech Connect (OSTI)

    Arends, J.; Sandusky, William F.

    2010-03-31T23:59:59.000Z

    This report represents findings of a design review team that evaluated construction documents (at the 70% level) and operating specifications for a new control tower and support building that will be built in Las Vegas, Nevada by the Federal Aviation Administration (FAA). The focus of the review was to identify measures that could be incorporated into the final design and operating specification that would result in additional energy savings for the FAA that would not have otherwise occurred.

  9. American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance Federal Aviation Administration – Project 209 Control Tower and Support Building Oakland, CA

    SciTech Connect (OSTI)

    Arends, J.; Sandusky, William F.

    2010-03-01T23:59:59.000Z

    This report represents findings of a design review team that evaluated construction documents (at the 70% level) and operating specifications for a new control tower and support building that will be build at Oakland, California by the Federal Aviation Administration (FAA). The focus of the review was to identify measures that could be incorporated into the final design and operating specification that would result in additional energy savings for the FAA that would not have otherwise occurred.

  10. Facilitating Sound, Cost-Effective Energy Management (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-04-01T23:59:59.000Z

    FEMP focuses on the needs of its Federal customers, delivering an array of products grouped into project transaction services, applied technology services, and decision support services. This document outlines FEMP services and programs.

  11. Facilitating Sound, Cost-Effective Energy Management (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-07-01T23:59:59.000Z

    FEMP focuses on the needs of its Federal customers, delivering an array of products grouped into project transaction services, applied technology services, and decision support services. This document outlines FEMP services and programs.

  12. Facilitating Sound, Cost-Effective Energy Management (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-04-01T23:59:59.000Z

    FEMP focuses on the needs of its Federal customers, delivering an array of products grouped into project transaction services, applied technology services, and decision support services. This document outlines FEMP services and programs.

  13. 2:00-2:30 Beverages, 2:30-4 PM Seminar One of the many challenges of energy production in cold regions is the design of

    E-Print Network [OSTI]

    2/4/2014 2:00-2:30 Beverages, 2:30-4 PM Seminar Abstract One of the many challenges of energy production in cold regions is the design of structures for ice actions. Ice formations can impinge against

  14. Design of a demand driven multi-item-multi-stage manufacturing system : production scheduling, WIP control and Kanban implementation

    E-Print Network [OSTI]

    Zhou, Xiaoyu, M. Eng Massachusetts Institute of Technology

    2009-01-01T23:59:59.000Z

    The project is conducted in a multi-item-multi-stage manufacturing system with high volume products. The objectives are to optimize the inventory structure and improve production scheduling process. The stock building plan ...

  15. Advanced turbine systems program: Conceptual design and product development. Quarterly report, November 1, 1995--January 31, 1996

    SciTech Connect (OSTI)

    NONE

    1996-04-09T23:59:59.000Z

    Several tasks were completed. Design and test of critical components are discussed. Plans for the next reporting period are outlined.

  16. American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance Federal Aviation Administration – Project 209 Control Tower and Support Building, Reno, Nevada

    SciTech Connect (OSTI)

    Arends, J.; Sandusky, William F.

    2010-06-30T23:59:59.000Z

    Pacific Northwest National Laboratory (PNNL) and Redhorse Corporation (Redhorse) conducted an energy audit on the Federal Aviation Administration (FAA) control tower and base building in Reno, Nevada. This report presents the findings of the energy audit team that evaluated construction documents and operating specifications (at the 100% level) and completed a site visit. The focus of the review was to identify measures that could be incorporated into the final design and operating specifications that would result in additional energy savings for the FAA that would not have otherwise occurred.

  17. American Recovery and Reinvestment Act (ARRA) - FEMP Technical Assistance - Federal Aviation Administration - Project 209 - Control Tower and Support Building, Boise, Idaho

    SciTech Connect (OSTI)

    Arends, J.; Sandusky, William F.

    2010-06-28T23:59:59.000Z

    This report documents an energy audit performed by Pacific Northwest National Laboratory (PNNL) and Redhorse Corporation (Redhorse) conducted on the Federal Aviation Administration (FAA) control tower and base building in Boise, Idaho. This report presents findings of the energy audit team that evaluated construction documents and operating specifications (at the 100% level) followed by a site visit of the facility under construction. The focus of the review was to identify measures that could be incorporated into the final design and operating specifications that would result in additional energy savings for FAA that would not have otherwise occurred.

  18. Conceptual design and system analysis of a poly-generation system for power and olefin production from natural gas

    E-Print Network [OSTI]

    Huang, Yinlun

    -production system based on coal and natural gas for the production of electric- ity and Dimethyl ether (DME) and electricity being more thermodynamically efficient and economically viable than single purpose power resources and environmental considerations. In some senses, energy shortages and environmental pollution

  19. System Analyses of High and Low-Temperature Interface Designs for a Nuclear-Driven High-Temperature Electrolysis Hydrogen Production Plant

    SciTech Connect (OSTI)

    E. A. Harvego; J. E. O'Brien

    2009-07-01T23:59:59.000Z

    As part of the Next Generation Nuclear Plant (NGNP) project, an evaluation of a low-temperature heat-pump interface design for a nuclear-driven high-temperature electrolysis (HTE) hydrogen production plant was performed using the UniSim process analysis software. The lowtemperature interface design is intended to reduce the interface temperature between the reactor power conversion system and the hydrogen production plant by extracting process heat from the low temperature portion of the power cycle rather than from the high-temperature portion of the cycle as is done with the current Idaho National Laboratory (INL) reference design. The intent of this design change is to mitigate the potential for tritium migration from the reactor core to the hydrogen plant, and reduce the potential for high temperature creep in the interface structures. The UniSim model assumed a 600 MWt Very-High Temperature Reactor (VHTR) operating at a primary system pressure of 7.0 MPa and a reactor outlet temperature of 900°C. The lowtemperature heat-pump loop is a water/steam loop that operates between 2.6 MPa and 5.0 MPa. The HTE hydrogen production loop operated at 5 MPa, with plant conditions optimized to maximize plant performance (i.e., 800°C electrolysis operating temperature, area specific resistance (ASR) = 0.4 ohm-cm2, and a current density of 0.25 amps/cm2). An air sweep gas system was used to remove oxygen from the anode side of the electrolyzer. Heat was also recovered from the hydrogen and oxygen product streams to maximize hydrogen production efficiencies. The results of the UniSim analysis showed that the low-temperature interface design was an effective heat-pump concept, transferring 31.5 MWt from the low-temperature leg of the gas turbine power cycle to the HTE process boiler, while consuming 16.0 MWe of compressor power. However, when this concept was compared with the current INL reference direct Brayton cycle design and with a modification of the reference design to simulate an indirect Brayton cycle (both with heat extracted from the high-temperature portion of the power cycle), the latter two concepts had higher overall hydrogen production rates and efficiencies compared to the low-temperature heatpump concept, but at the expense of higher interface temperatures. Therefore, the ultimate decision on the viability of the low-temperature heat-pump concept involves a tradeoff between the benefits of a lower-temperature interface between the power conversion system and the hydrogen production plant, and the reduced hydrogen production efficiency of the low-temperature heat-pump concept compared to concepts using high-temperature process heat.

  20. Automotive component product development enhancement through multi-attribute system design optimization in an integrated concurrent engineering framework

    E-Print Network [OSTI]

    Usan, Massimo, 1967-

    2005-01-01T23:59:59.000Z

    Automotive industry is facing a tough period. Production overcapacity and high fixed costs constrain companies' profits and challenge the very same existence of some corporations. Strangulated by the reduced cash availability ...

  1. Product design for supply chain : quantifying the costs of complexity in Hewlett-Packard's retail desktop PC business

    E-Print Network [OSTI]

    Raphel, Aaron Matthew

    2005-01-01T23:59:59.000Z

    Over the past several years, Hewlett-Packard Company's North America Consumer Computing (NACC) division has faced pressures to increase retail product variety in response to growing customer demand. As they pursue incremental ...

  2. Seismic design of a current woodframe structure and study of innovative products and damping systems in wood construction

    E-Print Network [OSTI]

    Mahjoub, Nina A. (Nina Azadeh)

    2007-01-01T23:59:59.000Z

    Wood structures have seen resurgence in popularity over the past several decades, especially in Western States of America, such as California. The industry keeps creating new structural wood products of exceptional strength, ...

  3. Design modification for the modular helium reactor for higher temperature operation and reliability studies for nuclear hydrogen production processes

    E-Print Network [OSTI]

    Reza, S.M. Mohsin

    2009-05-15T23:59:59.000Z

    Design options have been evaluated for the Modular Helium Reactor (MHR) for higher temperature operation. An alternative configuration for the MHR coolant inlet flow path is developed to reduce the peak vessel temperature (PVT). The coolant inlet...

  4. Thermodynamics of fission products in dispersion fuel designs - first principles modeling of defect behavior in bulk and at interfaces

    SciTech Connect (OSTI)

    Liu, Xiang-yand [Los Alamos National Laboratory; Uberuaga, Blas P [Los Alamos National Laboratory; Nerikar, Pankaj [Los Alamos National Laboratory; Sickafus, Kurt E [Los Alamos National Laboratory; Stanek, Chris R [Los Alamos National Laboratory

    2009-01-01T23:59:59.000Z

    Density functional theory (DFT) calculations of fission product (Xe, Sr, and Cs) incorporation and segregation in alkaline earth metal oxides, HfO{sub 2} and UO{sub 2} oxides, and the MgO/(U, Hf, Ce)O{sub 2} interfaces have been carried out. In the case of UO{sub 2}, the calculations were performed using spin polarization and with a Hubbard U term characterizing the on-sit Coulomb repulsion between the localized 5f electrons. The fission product solution energies in bulk UO{sub 2{+-}x} have been calculated as a function of non-stoichiometry x, and were compared to that in MgO. These calculations demonstrate that the fission product incorporation energies in MgO are higher than in HfO{sub 2}. However, this trend is reversed or reduced for alkaline earth oxides with larger cation sizes. The solution energies of fission products in MgO are substantially higher than in UO{sub 2{+-}x}, except for the case of Sr in the hypostoichiometric case. Due to size effects, the thermodynamic driving force of segregation for Xe and Cs from bulk MgO to the MgO/fluorite interface is strong. However, this driving force is relatively weak for Sr.

  5. Design and Testing of a Labview- Controlled Catalytic Packed- Bed Reactor System For Production of Hydrocarbon Fuels

    SciTech Connect (OSTI)

    Street, J.; Yu, F.; Warnock, J.; Wooten, J.; Columbus, E.; White, M. G.

    2012-05-01T23:59:59.000Z

    Gasified woody biomass (producer gas) was converted over a Mo/H+ZSM-5 catalyst to produce gasolinerange hydrocarbons. The effect of contaminants in the producer gas showed that key retardants in the system included ammonia and oxygen. The production of gasoline-range hydrocarbons derived from producer gas was studied and compared with gasoline-range hydrocarbon production from two control syngas mixes. Certain mole ratios of syngas mixes were introduced into the system to evaluate whether or not the heat created from the exothermic reaction could be properly controlled. Contaminant-free syngas was used to determine hydrocarbon production with similar mole values of the producer gas from the gasifier. Contaminant-free syngas was also used to test an ideal contaminant-free synthesis gas situation to mimic our particular downdraft gasifier. Producer gas was used in this study to determine the feasibility of using producer gas to create gasoline-range hydrocarbons on an industrial scale using a specific Mo/H+ZSM-5 catalyst. It was determined that after removing the ammonia, other contaminants poisoned the catalyst and retarded the hydrocarbon production process as well.

  6. Molten carbonate fuel cell product design & improvement - 2nd quarter, 1996. Quarterly report, April 1--June 30, 1996

    SciTech Connect (OSTI)

    NONE

    1997-05-01T23:59:59.000Z

    The main objective of this project is to establish the commercial readiness of a molten carbonate fuel cell power plant for distributed power generation, cogeneration, and compressor station applications. This effort includes marketing, systems design and analysis, packaging and assembly, test facility development, and technology development, improvement, and verification.

  7. Design modification for the modular helium reactor for higher temperature operation and reliability studies for nuclear hydrogen production processes 

    E-Print Network [OSTI]

    Reza, S.M. Mohsin

    2009-05-15T23:59:59.000Z

    of graphite removed from the PSR to create this inlet path. With the removal of ~10% of the graphite from PSR the PVT is reduced from 541 0C to 421 0C. A new design for the graphite block core has been evaluated and optimized to reduce the inlet coolant...

  8. Process Design and Economics for the Conversion of Algal Biomass to Biofuels: Algal Biomass Fractionation to Lipid- and Carbohydrate-Derived Fuel Products

    SciTech Connect (OSTI)

    Davis, R.; Kinchin, C.; Markham, J.; Tan, E.; Laurens, L.; Sexton, D.; Knorr, D.; Schoen, P.; Lukas, J.

    2014-09-01T23:59:59.000Z

    Beginning in 2013, NREL began transitioning from the singular focus on ethanol to a broad slate of products and conversion pathways, ultimately to establish similar benchmarking and targeting efforts. One of these pathways is the conversion of algal biomass to fuels via extraction of lipids (and potentially other components), termed the 'algal lipid upgrading' or ALU pathway. This report describes in detail one potential ALU approach based on a biochemical processing strategy to selectively recover and convert select algal biomass components to fuels, namely carbohydrates to ethanol and lipids to a renewable diesel blendstock (RDB) product. The overarching process design converts algal biomass delivered from upstream cultivation and dewatering (outside the present scope) to ethanol, RDB, and minor coproducts, using dilute-acid pretreatment, fermentation, lipid extraction, and hydrotreating.

  9. The division of Machine Design

    E-Print Network [OSTI]

    Zhao, Yuxiao

    Requirement engineering Simulation Multi- disciplinary design VR CAD Robust optimization 3D- printing Product

  10. FEMP Website Moves Into Energy.gov

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program in January moved its Web pages into Energy.gov, the U.S. Department of Energy's website.

  11. FEMP: Super energy savings performance contracts overview

    SciTech Connect (OSTI)

    NONE

    1999-09-07T23:59:59.000Z

    Authorized by the Energy Policy Act of 1992 (EPAct), the Energy Savings Performance Contract (ESPC) program was created to provide agencies with a quick and cost-effective way to finance energy-saving technologies. Under an ESPC, energy service companies (ESCOs) assume the capital costs of installing energy and water conservation equipment and renewable energy systems.

  12. FEMP Renewable Energy Fact Sheet: Photovoltaics

    SciTech Connect (OSTI)

    NONE

    1999-10-01T23:59:59.000Z

    Photovoltaic energy systems, which convert sunlight to electricity, can meet many different needs in Federal facilities. This fact sheet describes how photovoltaic (PV) energy systems can be used to provide electricity for lighting, communications, refrigeration, fans, signs, pumps, drilling equipment, emergency power packs, and cathodic (corrosion) protection, among others. Applications for PV power in Federal facilities include staff housing, parking areas, campgrounds, marinas, visitor centers, roadside communications equipment, ranger stations, underground pipelines, irrigation and disinfecting systems, and disaster response units. PV systems are particularly suitable and cost-effective for facilities that now use diesel power or that are in remote areas far from electric power lines.

  13. FEMP Director's Blog | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKET NO.

  14. FEMP Receives Internationally Recognized Training Accreditation |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 FederalTexasManager FAQS Reference Guide| DepartmentContracting

  15. DOE/FEMP Welcome and Announcements

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny:Revised Finding of No Significant6-2002DOE/EA-13135 Final Environmental(July

  16. Energy, Environmental, and Economic Analyses of Design Concepts for the Co-Production of Fuels and Chemicals with Electricity via Co-Gasification of Coal and Biomass

    SciTech Connect (OSTI)

    Eric Larson; Robert Williams; Thomas Kreutz; Ilkka Hannula; Andrea Lanzini; Guangjian Liu

    2012-03-11T23:59:59.000Z

    The overall objective of this project was to quantify the energy, environmental, and economic performance of industrial facilities that would coproduce electricity and transportation fuels or chemicals from a mixture of coal and biomass via co-gasification in a single pressurized, oxygen-blown, entrained-flow gasifier, with capture and storage of CO{sub 2} (CCS). The work sought to identify plant designs with promising (Nth plant) economics, superior environmental footprints, and the potential to be deployed at scale as a means for simultaneously achieving enhanced energy security and deep reductions in U.S. GHG emissions in the coming decades. Designs included systems using primarily already-commercialized component technologies, which may have the potential for near-term deployment at scale, as well as systems incorporating some advanced technologies at various stages of R&D. All of the coproduction designs have the common attribute of producing some electricity and also of capturing CO{sub 2} for storage. For each of the co-product pairs detailed process mass and energy simulations (using Aspen Plus software) were developed for a set of alternative process configurations, on the basis of which lifecycle greenhouse gas emissions, Nth plant economic performance, and other characteristics were evaluated for each configuration. In developing each set of process configurations, focused attention was given to understanding the influence of biomass input fraction and electricity output fraction. Self-consistent evaluations were also carried out for gasification-based reference systems producing only electricity from coal, including integrated gasification combined cycle (IGCC) and integrated gasification solid-oxide fuel cell (IGFC) systems. The reason biomass is considered as a co-feed with coal in cases when gasoline or olefins are co-produced with electricity is to help reduce lifecycle greenhouse gas (GHG) emissions for these systems. Storing biomass-derived CO{sub 2} underground represents negative CO{sub 2} emissions if the biomass is grown sustainably (i.e., if one ton of new biomass growth replaces each ton consumed), and this offsets positive CO{sub 2} emissions associated with the coal used in these systems. Different coal:biomass input ratios will produce different net lifecycle greenhouse gas (GHG) emissions for these systems, which is the reason that attention in our analysis was given to the impact of the biomass input fraction. In the case of systems that produce only products with no carbon content, namely electricity, ammonia and hydrogen, only coal was considered as a feedstock because it is possible in theory to essentially fully decarbonize such products by capturing all of the coal-derived CO{sub 2} during the production process.

  17. Design, Construction, and Implementation of Novel Biofuel Production Capabilities in Filamentous Fungi Presentation for BETO 2015 Project Peer Review

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny:Revised Finding of No53197E T A * S H I E L D *DepartmentTSDepartment3,ofDesign,

  18. Solar production of intermediate temperature process heat. Phase I design. Final report. [For sugarcane processing plant in Hawaii

    SciTech Connect (OSTI)

    None

    1980-08-01T23:59:59.000Z

    This report is the final effort in the Phase I design of a solar industrial process heat system for the Hilo Coast Processing Company (HCPC) in Pepeekeo, Hawaii. The facility is used to wash, grind and extract sugar from the locally grown sugarcane and it operates 24 hours a day, 305 days per year. The major steam requirements in the industrial process are for the prime movers (mill turbines) in the milling process and heat for evaporating water from the extracted juices. Bagasse (the fibrous residue of milled sugarcane) supplied 84% of the fuel requirement for steam generation in 1979, while 65,000 barrels of No. 6 industrial fuel oil made up the remaining 16%. These fuels are burned in the power plant complex which produces 825/sup 0/F, 1,250 psi superheated steam to power a turbogenerator set which, in addition to serving the factory, generates from 7 to 16 megawatts of electricity that is exported to the local utility company. Extracted steam from the turbo-generator set supplies the plant's process steam needs. The system consists of 42,420 ft./sup 2/ of parabolic trough, single axis tracking, concentrating solar collectors. The collectors will be oriented in a North-South configuration and will track East-West. A heat transfer fluid (Gulf Synfluid 4cs) will be circulated in a closed loop fashion through the solar collectors and a series of heat exchangers. The inlet and outlet fluid temperatures for the collectors are 370/sup 0/F and 450/sup 0/F respectively. It is estimated that the net useable energy delivered to the industrial process will be 7.2 x 10/sup 9/ Btu's per year. With an HCPC boiler efficiency of 78% and 6.2 x 10/sup 6/ Btu's per barrel of oil, the solar energy system will displace 1489 barrels of oil per year. (WHK)

  19. Microchannel Reactor System Design & Demonstration For On-Site H2O2 Production by Controlled H2/O2 Reaction

    SciTech Connect (OSTI)

    Adeniyi Lawal

    2008-12-09T23:59:59.000Z

    We successfully demonstrated an innovative hydrogen peroxide (H2O2) production concept which involved the development of flame- and explosion-resistant microchannel reactor system for energy efficient, cost-saving, on-site H2O2 production. We designed, fabricated, evaluated, and optimized a laboratory-scale microchannel reactor system for controlled direct combination of H2 and O2 in all proportions including explosive regime, at a low pressure and a low temperature to produce about 1.5 wt% H2O2 as proposed. In the second phase of the program, as a prelude to full-scale commercialization, we demonstrated our H2O2 production approach by ‘numbering up’ the channels in a multi-channel microreactor-based pilot plant to produce 1 kg/h of H2O2 at 1.5 wt% as demanded by end-users of the developed technology. To our knowledge, we are the first group to accomplish this significant milestone. We identified the reaction pathways that comprise the process, and implemented rigorous mechanistic kinetic studies to obtain the kinetics of the three main dominant reactions. We are not aware of any such comprehensive kinetic studies for the direct combination process, either in a microreactor or any other reactor system. We showed that the mass transfer parameter in our microreactor system is several orders of magnitude higher than what obtains in the macroreactor, attesting to the superior performance of microreactor. A one-dimensional reactor model incorporating the kinetics information enabled us to clarify certain important aspects of the chemistry of the direct combination process as detailed in section 5 of this report. Also, through mathematical modeling and simulation using sophisticated and robust commercial software packages, we were able to elucidate the hydrodynamics of the complex multiphase flows that take place in the microchannel. In conjunction with the kinetics information, we were able to validate the experimental data. If fully implemented across the whole industry as a result of our technology demonstration, our production concept is expected to save >5 trillion Btu/year of steam usage and >3 trillion Btu/year in electric power consumption. Our analysis also indicates >50 % reduction in waste disposal cost and ~10% reduction in feedstock energy. These savings translate to ~30% reduction in overall production and transportation costs for the $1B annual H2O2 market.

  20. Product grammar : construction and exploring solution spaces

    E-Print Network [OSTI]

    Chin, Ryan C. C., 1974-

    2004-01-01T23:59:59.000Z

    Developing a design methodology that accounts for system- and component-level parameters in the design of products is a challenge for design and manufacturing organizations. Designed products like automobiles, personal ...

  1. DESIGN FOR PRODUCT EMBEDDED DISASSEMBLY

    E-Print Network [OSTI]

    Saitou, Kazuhiro "Kazu"

    -objective genetic algorithm 1. INTRODUCTION Increased regulatory pressures (e.g., EU's WEEE directive) and voluntary

  2. LED Provides Effective and Efficient Parking Area Lighting at...

    Broader source: Energy.gov (indexed) [DOE]

    White Light Options for Parking Area Lighting Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report Guide to FEMP-Designated Parking Lot...

  3. Federal Energy Management Program eTraining Core Courses

    Broader source: Energy.gov [DOE]

    Video summarizes the Federal Energy Management Program's (FEMP) eTraining courses available anytime online on the Whole Building Design Guide website.

  4. Covered Product Categories (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2011-08-01T23:59:59.000Z

    Overview of the U.S. Department of Energy Federal Energy Management Program Energy-Efficient Product Procurement Program and its designated product category list.

  5. All products of the future clothes, household devices, lamps will contain electronic units. Graduates in Electronic Design Engineering will be able

    E-Print Network [OSTI]

    . Graduates in Electronic Design Engineering will be able to design both electronics and system software will also help to reduce carbon emissions. The Electronic Design Engineering programme equips students students to apply skills within real-life company projects. The Electronic Design Engineering programme

  6. Metallurgical Process Design A tribute to Douglas' conceptual design approach

    E-Print Network [OSTI]

    Linninger, Andreas A.

    and systematic flowsheet generation1-2. . Although perfected for continuous petrochemical processes, this work1 Metallurgical Process Design ­ A tribute to Douglas' conceptual design approach Andreas A. Linninger Laboratory for Product and Process Design Department of Chemical Engineering, University

  7. Case for sustainability in strategy and operations : overcoming the challenges of product design in creating competitive advantages in circular supply chains

    E-Print Network [OSTI]

    Dalmia, Niraj

    2014-01-01T23:59:59.000Z

    The previous industrial revolutions coupled with long-established business models have created a lock-in towards a linear 'take-make-dispose' model of production and consumption - products are manufactured using non-renewable ...

  8. Microsystem product development.

    SciTech Connect (OSTI)

    Polosky, Marc A.; Garcia, Ernest J.

    2006-04-01T23:59:59.000Z

    Over the last decade the successful design and fabrication of complex MEMS (MicroElectroMechanical Systems), optical circuits and ASICs have been demonstrated. Packaging and integration processes have lagged behind MEMS research but are rapidly maturing. As packaging processes evolve, a new challenge presents itself, microsystem product development. Product development entails the maturation of the design and all the processes needed to successfully produce a product. Elements such as tooling design, fixtures, gages, testers, inspection, work instructions, process planning, etc., are often overlooked as MEMS engineers concentrate on design, fabrication and packaging processes. Thorough, up-front planning of product development efforts is crucial to the success of any project.

  9. Evaluating the End-of-Life Phase of Consumer Electronics:Methods and Tools to Improve Product Design and Material Recovery

    E-Print Network [OSTI]

    Mangold, Jennifer Ann

    2013-01-01T23:59:59.000Z

    L. Meyer and B. Bras. Rare earth metal recycling. In IEEEattention on recovering rare earth metals from electronics,available to extract rare earth metals from waste products;

  10. Biological production of products from waste gases

    DOE Patents [OSTI]

    Gaddy, James L. (Fayetteville, AR)

    2002-01-22T23:59:59.000Z

    A method and apparatus are designed for converting waste gases from industrial processes such as oil refining, and carbon black, coke, ammonia, and methanol production, into useful products. The method includes introducing the waste gases into a bioreactor where they are fermented to various products, such as organic acids, alcohols, hydrogen, single cell protein, and salts of organic acids by anaerobic bacteria within the bioreactor. These valuable end products are then recovered, separated and purified.

  11. A Study of How Products Contribute to the Emotional Aspects of Human Experience Jodi Forlizzi, Assistant Professor, HCII and School of Design

    E-Print Network [OSTI]

    Mutlu, Bilge

    A Study of How Products Contribute to the Emotional Aspects of Human Experience Author 1 Jodi to the Emotional Aspects of Human Experience Jodi Forlizzi, Bilge Mutlu, and Carl DiSalvo Human the emotional aspects of products is of interest for any field concerned with human experience. The vast amount

  12. BA 290N-2, ME290P-1, INFOSYS 290P-4 and DSID125 Managing the New Product Development Process: Design Theory and Methods

    E-Print Network [OSTI]

    Agogino, Alice M.

    Process: Design Theory and Methods Professors Alice M. Agogino, Sara Beckman and Leslie Speer Fall 2007-1058, (415) 464-0517, beckman@haas.berkeley.edu Leslie Speer, Industrial Design Program, San Jose State University, Art 231, (408) 924-4376, (510) 658- 3177, Leslie.Speer@sjsu.edu Teaching Assistants: Jonathan

  13. Covered Product Category: Industrial Luminaires (High/Low Bay)

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance and Federal efficiency requirements for Industrial Luminaires (High/Low Bay). Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  14. The development and application of a questionnaire designed to measure pre-existing, process, and outcome variables in the productivity measurement and enhancement

    E-Print Network [OSTI]

    Decuir, Arlette Desha

    1997-01-01T23:59:59.000Z

    The ProMES questionnaire was developed to assess individuals' experiences as they relate to the implementation of the Productivity Measurement and Enhancement System. The questionnaire, which resulted in a total of 30 subscales that assess...

  15. Production and inventory control of a multi-item multi-stage manufacturing system : simulation modeling, capacitated shipment planning and Kanban design

    E-Print Network [OSTI]

    Rizvi, Syed Zia Abbas

    2009-01-01T23:59:59.000Z

    The project work presented in this thesis has proposed solutions related to the control of production and work-in-process inventory in a multi-item multi-stage manufacturing system. A suitable base-stock inventory control ...

  16. Estimating the upper limit of gas production from Class 2 hydrate accumulations in the permafrost: 2. Alternative well designs and sensitivity analysis

    E-Print Network [OSTI]

    Moridis, G.

    2011-01-01T23:59:59.000Z

    m). As in all cases of gas hydrates (Moridis et al. , 2007;by destroying the secondary gas hydrate barrier (if such aInduced Gas Production From Class 1 Hydrate Deposits,” SPE

  17. Comparing Product Development Processes and Managing Risk

    E-Print Network [OSTI]

    Unger, Darian W.

    Product Development Processes (PDPs) require careful design to reduce development time, create better products and manage the risks of bringing new products to market. This paper investigates the relationship between product ...

  18. Dynamically adapting design and usability in consumer technology products to technology and market life-cycles : a case study of smartphones

    E-Print Network [OSTI]

    Subramanian, Sangita, 1976-

    2009-01-01T23:59:59.000Z

    Design-driven business strategy has received a lot of attention in recent times, with Apple frequently standing out as an exemplar of the success of such a strategy. Most of the existing literature, while emphasizing the ...

  19. Topical report on a preconceptual design for the Spallation-Induced Lithium Conversion (SILC) target for the accelerator production of tritium (APT)

    SciTech Connect (OSTI)

    Van Tuyle, G.J.; Cokinos, D.M.; Czajkowski, C.; Franz, E.M.; Kroeger, P.; Todosow, M.; Youngblood, R.; Zucker, M.

    1993-09-30T23:59:59.000Z

    The preconceptual design of the APT Li-Al target system, also referred to as the Spallation-Induced Lithium Conversion (SILC), target system, is summarized in this report. The system has been designed to produce a ``3/8 Goal`` quantity of tritium using the 200-mA, 1.0 GeV proton beam emerging from the LANL-designed LINAC. The SILC target system consists of a beam expander, a heavy-water-cooled lead spallation neutron source assembly surrounded by light-water-cooled Li-Al blankets, a target window, heat removal systems, and related safety systems. The preconceptual design of each of these major components is described. Descriptions are also provided for the target fabrication, tritium extraction, and waste-steam processes. Performance characteristics are presented and discussed.

  20. The following are appendices A, B1 and B2 of our paper, "Integrated Process Modeling and Product Design of Biodiesel Manufacturing", that appears in the Industrial and

    E-Print Network [OSTI]

    Liu, Y. A.

    Design of Biodiesel Manufacturing", that appears in the Industrial and Engineering Chemistry Research a Biodiesel Process Model To access NIST TDE Data Engine in Aspen Plus version 2006.5 or V7.0 Step 1. Enter

  1. MECO Production Target Developments

    E-Print Network [OSTI]

    McDonald, Kirk

    be reoptimized Tungsten target Simulations of design parameters with GEANT3 indicate that both production targetMECO Production Target Developments James L. Popp University of California, Irvine NuFact'03 Columbia, June, 2003 #12;June, 2003J.L.Popp, UCI MECO Production Target 2 MECO Collaboration Institute

  2. Design tool: a software for capturing design intent

    E-Print Network [OSTI]

    Velamakanni, Ravindra

    1999-01-01T23:59:59.000Z

    The central purpose of design is to create products that satisfy societal needs within specified constraints. This is a daunting task that involves making a large number of design decisions usually with insufficient information. This results...

  3. Designing a better hair straightener

    E-Print Network [OSTI]

    Read, Melissa B. (Melissa Beth), 1982-

    2004-01-01T23:59:59.000Z

    The Simply Straight Hair Brush was designed and built. The aim of the Simply Straight Hair Brush was to straighten hair faster and better than any product currently on the market. The current products were studied and the ...

  4. Design with Uncertain Technology Evolution 

    E-Print Network [OSTI]

    Arendt, Jonathan Lee

    2012-10-19T23:59:59.000Z

    Design is an uncertain human activity involving decisions with uncertain outcomes. Sources of uncertainty in product design include uncertainty in modeling methods, market preferences, and performance levels of subsystem technologies, among many...

  5. Complexity reduction in automotive design and development

    E-Print Network [OSTI]

    Ziegler, Ronald J., 1965-

    2005-01-01T23:59:59.000Z

    Automobiles are complex products. High product complexity drives high levels of design and process complexity and complicatedness. This thesis attempts to reduce complicatedness in the automotive vehicle design and development ...

  6. Nanotechnology for Solar-hydrogen Production via Photoelectrochemical Water-splitting: Design, Synthesis, Characterization, and Application of Nanomaterials and Quantum Dots

    E-Print Network [OSTI]

    Alenzi, Naser D.

    2012-02-14T23:59:59.000Z

    -scale ..................................................... 35 1.25 Atoms nucleation and growth rate during synthesis .................................. 36 1.26 The AM 1.5 solar spectrum as function of photon energy. ........................ 37 1.27 Thermal solar energy systems (A) parabolic dish (B... Page 1.1 Hydrogen production pathways ................................................................. 4 1.2 Solar to hydrogen conversion pathways, STC is solar thermochemical, CST is concentrating solar thermal, and PEC...

  7. Concurrent design for optimal quality and cycle time

    E-Print Network [OSTI]

    Wei, Yu-Feng, 1970-

    2001-01-01T23:59:59.000Z

    Product and manufacturing system design are the core issues in product development and dominate the profitability of a company. In order to assess and optimize the product and manufacturing system design, an objective ...

  8. Automotive Component Product Development Enhancement

    E-Print Network [OSTI]

    of Science in Engineering and Management February 2005 ABSTRACT Automotive industry is facing a tough periodAutomotive Component Product Development Enhancement Through Multi-Attribute System Design Engineering Systems Division #12;Automotive Component Product Development Enhancement Through Multi

  9. Advanced Turbine Systems Program conceptual design and product development. Task 3.0, Selection of natural gas-fired Advanced Turbine System

    SciTech Connect (OSTI)

    NONE

    1994-12-01T23:59:59.000Z

    This report presents results of Task 3 of the Westinghouse ATS Phase II program. Objective of Task 3 was to analyze and evaluate different cycles for the natural gas-fired Advanced Turbine Systems in order to select one that would achieve all ATS program goals. About 50 cycles (5 main types) were evaluated on basis of plant efficiency, emissions, cost of electricity, reliability-availability-maintainability (RAM), and program schedule requirements. The advanced combined cycle was selected for the ATS plant; it will incorporate an advanced gas turbine engine as well as improvements in the bottoming cycle and generator. Cost and RAM analyses were carried out on 6 selected cycle configurations and compared to the baseline plant. Issues critical to the Advanced Combined Cycle are discussed; achievement of plant efficiency and cost of electricity goals will require higher firing temperatures and minimized cooling of hot end components, necessitating new aloys/materials/coatings. Studies will be required in combustion, aerodynamic design, cooling design, leakage control, etc.

  10. Quantification of design margins/safety factors based on the prediction uncertainty in tritium production rate from fusion integral experiments of the USDOE/JAERI collaborative program on fusion blanket neutronics

    SciTech Connect (OSTI)

    Youssef, M.Z.; Kumar, A.; Abdou, M.A. [Univ. of California, Los Angeles, CA (United States)] [and others

    1994-12-31T23:59:59.000Z

    Various engineering-oriented fusion integral experiments were performed within the USDOE/JAERI Collaborative Program on Fusion Blanket Neutronics during the last decade. The objectives of this ten-year program were: (a) to establish new experimental techniques for design-related neutronics experiments, (b) to provide experimental data on local and integrated parameters such as tritium production rate, nuclear heating, and activation for the purpose of assessing the accuracies of present nuclear data and calculational methods, and (c) to provide designers with design margin for important responses. Tritium breeding rate (TPR) has the prime focus among other reactions. The program consisted of three phases in which local and integrated measurements inside a Li{sub 2}O test assembly that has various engineering features of a prototypical blanket (e.g. SS FW, H{sub 2}O coolant channels, beryllium multiplier). The analysis of the experiments were performed independently by the US and JAERI using their own codes/databases. A wide range of the calculated-to-experimental (C/E) values were observed in all these experiments for local TPR from Li-6 (T{sub 6}), from Li-7 (T{sub 7}), and from Li-natural (T{sub n}). In this paper, the experimental and calculational data sets of local TPR in each experiment were interpreted to give estimate to the prediction uncertainty, u{sub i}, of the line-integrated TPR and its standard deviation, {sigma}{sub i}.

  11. Fusion integral experiments and analysis and the determination of design safety factors - II: Application to the prediction uncertainty of tritium production rate from the U.S. DOE/JAERI collaborative program on fusion blanket neutronics

    SciTech Connect (OSTI)

    Youssef, M.Z.; Kumar, A.; Abdou, M.A. [Univ. of California, Los Angeles, CA (United States)] [and others

    1995-09-01T23:59:59.000Z

    Many fusion integral experiments were performed during the last decade within a well-established collaboration between the United States and Japan on fusion breeder neutronics. The tritium production rate (TPR) has the prime focus among other reactions. The experimental and calculational data sets of local TPR in each experiment were interpolated to give an estimate of the prediction uncertainty, and the standard deviation, of the line-integrated TPR, a quantity that is closely related to the total breeding ratio (TBR) in the test assembly. A novel methodology developed during the collaboration was applied to arrive at estimates to design safety factors that fusion blanket designers can use to ensure that the achievable TBR in a blanket does not fall below a minimum required value. Associated with each safety factor is a confidence level, designers may choose to have, that calculated TPR will not exceed the actual measured value. Higher confidence levels require larger safety factors. Tabular and graphical forms for these factors are given, as derived independently for TPR from Li-6(T{sub 6}), Li-7 (T{sub 7}), and natural lithium (T{sub n}). Furthermore, distinction was made between safety factors based on the technique applied, discrete ordinates methods, and Monte Carlo methods in the U.S. calculations, JAERI`s calculations, and in both calculations considered simultaneously. The derived factors are applicable to TPR in Li{sub 2}O breeding material, 48 refs., 51 figs., 7 tabs.

  12. Journal of Engineering Design, Vol. 10, No. 2, 1999 De ning the Engine Design Process

    E-Print Network [OSTI]

    Salustri, Filippo A.

    the authors investigated the company's existing design process, identi® ed areas for improvement engineering enterprises, there is constant pressure to shorten lead times while improving product quality. LOCKLEDGE & FILIPPO A. SALUSTRI SUMMARY Shortening design lead times while maintaining product quality

  13. Scale-Up of World Record 16.5% CdTe Cell Design for a 50 MWp Production Facility: September 27, 2007 - March 26, 2009

    SciTech Connect (OSTI)

    Seymour, F. H.

    2011-05-01T23:59:59.000Z

    This final report covers progress made on subcontract NAT-7-77015-07 by PrimeStar Solar Inc. for the 18 month period from September 27, 2007 through March 26, 2009. The project objectives were to accelerate the commercialization of the world record 16.5% efficiency cadmium telluride photovoltaic technology. This was done by developing high performance 6"x6" prototype mini-modules and by designing and commissioning a pilot line for manufacturing of commercial sized 60cmx120cm modules. This subcontract aligns with the SAI program by accelerating the development of high efficiency low cost CdTe solar PV module manufacturing. This will contribute to the goal of PV grid parity by 2015. Progress with the deliverables and milestones in this subcontract constitutes progress towards the KPP and milestone objectives for the SAI program.

  14. Microsoft Word - FEMP Industry Days FAQ.docx

    Office of Environmental Management (EM)

    DOE like our company's small business contracting managers to attend, and should our ESCO consider giving a presentation or providing small business exhibits to engage small...

  15. FEMP Offers Training on Distributed-Scale Renewable Energy Projects...

    Energy Savers [EERE]

    be able to: Plan facility renewable energy projects using available screening tools for renewable energy resources, savings to investment ratio analysis, and feasibility studies...

  16. Ocean Energy Technology Overview: Federal Energy Management Program (FEMP)

    SciTech Connect (OSTI)

    Not Available

    2009-07-01T23:59:59.000Z

    Introduction to and overview of ocean renewable energy resources and technologies prepared for the U.S. Department of Energy Federal Energy management Program.

  17. FEMP Expands ESPC ENABLE Program to Include More Energy Conservation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    new energy conservation measures (ECMs): solar photovoltaic (PV) and simple one-for-one heating, ventilation, and air conditioning (HVAC) system replacement (small building...

  18. Overview of the ESCO Selection Process and FEMP ESPC Templates

    Broader source: Energy.gov [DOE]

    Document provides a flowchart showing the steps for selecting an energy services company (ESCO) for a Federal project and energy savings performance contract (ESPC) templates to assist with the process.

  19. FEMP Presents Latest Training Course on Advanced Energy Savings...

    Energy Savers [EERE]

    and performance matrix in summarizing and assigning risks or responsibilities to the energy service company (ESCO), agency, or both The importance of measurements and...

  20. "FEMP Support Through Initial Proposal Review for Contractor...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Agency ESPC Delivery Order. ","Workshop Materials and electronic copies of contracts, DO RFP formats and other guidelines","Agency will identify acquisition team members who should...

  1. FEMP ESPC Best Practices: Agency Plan and Variances

    Broader source: Energy.gov [DOE]

    Document serves as a checklist for tracking agency use of Federal Energy Management Program energy savings performance contracts (ESPC) best practices.

  2. FEMP/NTDP Technology Installation Review New Technology

    E-Print Network [OSTI]

    and the ventilation pathways among and over office partitions. Compounding this problem, there has been a growing and ventilation environment. Since its original introduction in West Germany during the 1950s, the open plan

  3. FEMP (Federal Energy Management Program) presents alternative financing guidance memoranda

    SciTech Connect (OSTI)

    NONE

    1998-06-01T23:59:59.000Z

    Utility financing of energy efficient measures becomes easier to accomplish with the two new alternative financing guidance memoranda, released April 17, 1998, that address the use of utility incentives for Federal facilities. The memoranda have been approved by the Alternative Financing Guidance Committee on the Interagency Energy Management Task Force. The memoranda include: (1) Policy Statement No. 001: Authority to Sole Source Utility Service Contracts as Referenced in Section 152 of the Energy Policy Act (EPACT) of 1992; and (2) Policy Statement No. 002: Congressional Notification for Utility Projects Under the Authority of Section 152 of the Energy Policy Act (EPACT) of 1992. The purpose for developing the financing memoranda was to address specific issues within current Federal procurement regulations that require clarification or guidance. This new guidance will allow for increased use of utility incentives as a means of financing energy efficient and life cycle cost-effective projects in Federal facilities.

  4. FEMP 2015 Funding Opportunity Announcement | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKET NO. 11-59-LNGCustomer2015

  5. FEMP Exterior Solid-State Lighting Technology Pilot

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKET NO.FEDERAL ENERGY

  6. FEMP Launches New Training Search Tool | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKET NO.FEDERAL

  7. FEMP Offers New Training Series on Renewable Energy Technologies |

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKET NO.FEDERALDepartment of

  8. FEMP Offers New Training on Photovoltaic Operations and Maintenance Best

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKET

  9. FEMP Presents Latest Training Course on Advanced Energy Savings Performance

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKETPlanning toPeer Review

  10. FEMP Publishes Aspinall Courthouse Case Study | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T,OfficeEnd of Year 2010SaltInstrumentation andFE DOCKETPlanning toPeer

  11. Energy Savings Performance Contracts: FEMP Assistance | Department of

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011 Strategic Plan Departmentof EnergyPublic Law of the 109thEnergy SaverENERGY

  12. FEMP Completes 2000th Renewable Energy Optimization Screening | Department

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011 Strategic Plan| Department of Energy 088:EnergyFAR27.pdfFE DOCKETFEDERALFEMAof

  13. Federal Energy Management Program (FEMP) Technical Assistance Request

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed offOCHCO2: FinalOffers New Training on Energy ManagementAugustin2012)4 News5Management CasePortal

  14. FEMP Resources for Sustainable Buildings | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual SiteofEvaluating A PotentialJumpGerman Aerospace CenterEverlightOpenEyeforenergyFEM

  15. FEMP Solar Hot Water Calculator | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual SiteofEvaluating A PotentialJumpGerman Aerospace CenterEverlightOpenEyeforenergyFEMSolar Hot

  16. Federal Energy Management Program (FEMP) Training Resources | Open Energy

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual SiteofEvaluating A PotentialJumpGerman AerospaceEfficiency

  17. The FEMP Awards Program: Fostering Institutional Change and Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33Frequently AskedEnergyIssuesEnergy Solar Decathlon2001 PowerofUse ofManagement Excellence |

  18. Federal Energy Management Program (FEMP) Technical Assistance Request

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in RepresentativeDepartmentEnergy

  19. FEMP First Thursday Seminar Offers Training on New Federal

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 FederalTexasManager FAQS Reference Guide

  20. FEMP SUGGESTED ESPC MILESTONE PLAN | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 FederalTexasManager FAQS Reference Guide| DepartmentContractingReleases

  1. FEMP Services Interagency Agreement for DOE ESPC Support | Department of

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122Commercial602 1,39732 DOEDepartment of EnergyEricDocuments andofPressEnergy

  2. Microsoft Word - FEMP-State MOU pdf version.doc

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33Frequently Asked Questions forCheneyNovember S. DEPARTMENTtheStatusUNDERSTANDING BETWEEN THE U.S.

  3. US DOE Federal Energy Management Program (FEMP) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to:Ezfeedflag JumpID-fTri Global Energy LLC Place: Dallas,UGIURDB Schema Documentation?

  4. FEMP Announces New Utilities Offering UESCs | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN Cameron

  5. FEMP Expands ESPC ENABLE Program to Include More Energy Conservation

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN8. REVIEW OF

  6. FEMP First Thursday Seminar Offers Training on New Federal

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN8.

  7. FEMP Launches New Technical Assistance Request Portal | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC PLAN8.Energy

  8. FEMP Offers New Training Series on Renewable Energy Technologies |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFIC

  9. FEMP Offers New Training on Photovoltaic Operations and Maintenance Best

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFICPractices | Department of

  10. FEMP Offers Training on Energy Efficiency Expert Evaluations | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFICPractices |of Energy

  11. FEMP Releases AFFECT Funding Opportunity Announcement | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFICPractices |ofSystems

  12. FEMP Releases ESPC Request for Information Results | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFICPractices |ofSystemsESPC

  13. FEMP SUGGESTED ESPC MILESTONE PLAN | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in Representative Geologic MediaTreatmentPROJECT-SPECIFICPractices

  14. US DOE Federal Energy Management Program (FEMP) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualProperty Edit withTianlin Baxin HydropowerTrinityTurnbullGlobal Map-Annex 1 JumpICSViewDOE 20%

  15. US DOE Federal Energy Management Program (FEMP) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualProperty Edit withTianlin Baxin HydropowerTrinityTurnbullGlobal Map-Annex 1 JumpICSViewDOE

  16. Production Leveling (Heijunka) Implementation in a Batch Production System: a Case Study

    E-Print Network [OSTI]

    Boyer, Edmond

    Production Leveling (Heijunka) Implementation in a Batch Production System: a Case Study Luciano a case study of an implementation of a new method for Production Leveling designed for batch production. It includes prioritizing criteria of products and level production plan. Moreover, it was applied

  17. 2014 Race to Zero Student Design Competition: University of Pittsburgh...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    showing that one of the most popular production home designs can be designed to be a zero net energy home. Technical Strategy Enclosure: Staggered Stud Wall system,...

  18. Rampressor Turbine Design

    SciTech Connect (OSTI)

    Ramgen Power Systems

    2003-09-30T23:59:59.000Z

    The design of a unique gas turbine engine is presented. The first Rampressor Turbine engine rig will be a configuration where the Rampressor rotor is integrated into an existing industrial gas turbine engine. The Rampressor rotor compresses air which is burned in a traditional stationary combustion system in order to increase the enthalpy of the compressed air. The combustion products are then expanded through a conventional gas turbine which provides both compressor and electrical power. This in turn produces shaft torque, which drives a generator to provide electricity. The design and the associated design process of such an engine are discussed in this report.

  19. Metro Vancouver: Designing for Urban Food Production

    E-Print Network [OSTI]

    Roehr, Daniel; Kunigk, Isabel

    2009-01-01T23:59:59.000Z

    green streets, and green energy interventions in cities.farming, public space, green energy, social, and educational

  20. Level 1 2013/14 Product Design

    E-Print Network [OSTI]

    Harman, Neal.A.

    , heat, transport) Energy efficiency Embedded energy Stern, Kyoto, Rio, Rio+20. How to bring global metric? Greenwash. "Sustainability"+business as usual. The global North-South divide (wealth, energy use, smog, noise. Bio-fuels Low Carbon Manufacturing Case study: Tata steel Port Talbot energy recovery

  1. Product Design for the Developing World

    E-Print Network [OSTI]

    Greer, Julia R.

    University, Kerala, India #12;Projects Biopower (9:40 pm) The development of biogas technology as an alternative energy source is becoming increasingly important in India. Biogas is a fuel produced from on individual biogas tanks, which are especially beneficial for families in rural areas where organic waste

  2. Product Design in Enterprise Wide Optimization

    E-Print Network [OSTI]

    Grossmann, Ignacio E.

    Changing Distribution Model - Uncontrolled Shipping OEM Wholesale Wholesale OEM Wholesale #12;The Markets

  3. Metro Vancouver: Designing for Urban Food Production

    E-Print Network [OSTI]

    Roehr, Daniel; Kunigk, Isabel

    2009-01-01T23:59:59.000Z

    green streets, and green energy interventions in cities.farming, public space, green energy, social, and educationalFor example, energy intensive green house agriculture may

  4. Human-Centered Sustainable Product Design

    E-Print Network [OSTI]

    Agogino, Alice M.

    , and elsewhere) !!Automobiles !! Packaging !! Waste electronics and appliances (e.g., WEEE) !! Hazardous substance bans (e.g., RoHS) !! Chemical hazard reporting (e.g. REACH) ·!Greenhouse gas reduction treaties and targets !!Kyoto Protocol !!U.S. city and state initiatives (e.g., California) Regulatory Drivers #12

  5. Level M 2013/14 Product Design

    E-Print Network [OSTI]

    Harman, Neal.A.

    -3-540-30697-9 ReeveD, Risk and reliability: coastal and hydraulic engineering, Spon Press, 2009.ISBN: ISBN13: 978

  6. Malczewski Product Design LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to: navigation, searchOfRose Bend < MHKconvertersource History View NewWindMalaysia:

  7. eco-design arunas oslapas, idsa

    E-Print Network [OSTI]

    Zaferatos, Nicholas C.

    #12;eco-design strategies arunas oslapas, idsa western washington university #12;"Only one in 10 of product Shipping Packaging Advertising Printing of instruction manuals Use of product Energy consumption

  8. Material and processes selection in conceptual design 

    E-Print Network [OSTI]

    Krishnakumar, Karthikeyan

    2005-02-17T23:59:59.000Z

    Materials and manufacturing processes are an integral part of the design of a product. The need to combine materials and manufacturing processes selection during the early stages of the design has previously been realized. The work that generally...

  9. A design tool for reusing integration knowledge in simulation models

    E-Print Network [OSTI]

    Han, Sangmok

    2006-01-01T23:59:59.000Z

    In the academic field of computer-aided product development, the role of the design tool is to support engineering designers to develop and integrate simulation models. Used to save time and costs in product development ...

  10. Procuring Energy-Efficient Products (Fact Sheet) (Revised)

    SciTech Connect (OSTI)

    Not Available

    2012-08-01T23:59:59.000Z

    Overview of the U.S. Department of Energy Federal Energy Management Program Energy-Efficient Product Procurement Program and its designated product category list.

  11. automated plant production: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of NTFPs to forest farming practices focused on particular marketable products. Non-timber forest products Fall 2014 Webinar Series Liskiewicz, Maciej 204 Automated design of...

  12. Production of Gasoline and Diesel from Biomass via Fast Pyrolysis...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Production of Gasoline and Diesel from Biomass via Fast Pyrolysis, Hydrotreating and Hydrocracking: A Design Case Production of Gasoline and Diesel from Biomass via Fast Pyrolysis,...

  13. Chapter 2: Whole-Buildling Design

    Broader source: Energy.gov (indexed) [DOE]

    manner that minimizes environ- mental impacts while maximizing employee health and productivity should begin with process - how you will go about planning, designing, and building...

  14. Design, construction and operational results of the IGBT controlled solid state modulator high voltage power supply used in the high power RF systems of the Low Energy Demonstration Accelerator of the accelerator production of tritium (APT) project

    SciTech Connect (OSTI)

    Bradley, J.T. III; Rees, D.; Przeklasa, R.S. [Los Alamos National Lab., NM (United States); Scott, M.C. [Continental Electronics Corp., Dallas, TX (United States)

    1998-12-31T23:59:59.000Z

    The 1700 MeV, 100 mA Accelerator Production of Tritium (APT) Proton Linac will require 244 1 MW, continuous wave RF systems. 1 MW continuous wave klystrons are used as the RF source and each klystron requires 95 kV, 17 A of beam voltage and current. The cost of the DC power supplies is the single largest percentage of the total RF system cost. Power supply reliability is crucial to overall RF system availability and AC to DC conversion efficiency affects the operating cost. The Low Energy Demonstration Accelerator (LEDA) being constructed at Los Alamos National Laboratory (LANL) will serve as the prototype and test bed for APT. The design of the RF systems used in LEDA is driven by the need to field test high efficiency systems with extremely high reliability before APT is built. The authors present a detailed description and test results of one type of advanced high voltage power supply system using Insulated Gate Bipolar Transistors (IGBTs) that has been used with the LEDA High Power RF systems. The authors also present some of the distinctive features offered by this power supply topology, including crowbarless tube protection and modular construction which allows graceful degradation of power supply operation.

  15. CALIFORNIA ENERGY Small HVAC System Design Guide

    E-Print Network [OSTI]

    CALIFORNIA ENERGY COMMISSION Small HVAC System Design Guide DESIGNGUIDELINES October 2003 500;#12;Small HVAC System Design Guide Acknowledgements i Acknowledgements The products and outcomes presented; Darren Goody, PECI, Design Guide review. #12;Small HVAC System Design Guide Preface ii Preface The Small

  16. The production of iron carbide

    SciTech Connect (OSTI)

    Anderson, K.M.; Scheel, J. [Nucor Iron Carbide, Inc., Point Lisas (Trinidad and Tobago)

    1997-12-31T23:59:59.000Z

    From start-up in 1994 to present, Nucor`s Iron Carbide plant has overcome many obstacles in achieving design production. Many of these impediments were due to flaws in equipment design. With the integration existing within the plant, limitations in any one system reduced the operating capacity of others. For this reason, as modifications were made and system capacities were increased, the need for additional modifications became apparent. Subsequently, operating practices, maintenance scheduling, employee incentives, and production objectives were continually adapted. This paper discusses equipment and design corrections and the quality issues that contributed to achieving the plant`s production capacity.

  17. Digital Styling for Designers: in Prospective Automotive Design

    E-Print Network [OSTI]

    Toronto, University of

    }@vsl.gifu-u.ac.jp Abstract. Although a great part of the new-product development process in automotive industry is already method for professional automotive stylists. 1. Introduction The automotive industry has beenDigital Styling for Designers: in Prospective Automotive Design Seok-Hyung Bae and Ryugo Kijima

  18. Reliability-based casing design

    SciTech Connect (OSTI)

    Maes, M.A. [Univ. of Calgary, Alberta (Canada). Civil Engineering Dept.; Gulati, K.C.; Johnson, R.C. [Mobil Research and Development Corp., Dallas, TX (United States); McKenna, D.L. [Mobil Producing Nigeria, Lagos (Nigeria); Brand, P.R.; Lewis, D.B. [Mobil E and P Technical Center, Dallas, TX (United States)

    1995-06-01T23:59:59.000Z

    The present paper describes the development of reliability-based design criteria for oil and/or gas well casing/tubing. The approach is based on the fundamental principles of limit state design. Limit states for tubulars are discussed and specific techniques for the stochastic modeling of loading and resistance variables are described. Zonation methods and calibration techniques are developed which are geared specifically to the characteristic tubular design for both hydrocarbon drilling and production applications. The application of quantitative risk analysis to the development of risk-consistent design criteria is shown to be a major and necessary step forward in achieving more economic tubular design.

  19. Financial modeling of new product development economics

    E-Print Network [OSTI]

    Balasubramaniam, Anitha

    2014-01-01T23:59:59.000Z

    Product design and development is a complex process that involves extensive engineering considerations as well as management decisions based on the overall vision for the product. Traditionally, most decision making in ...

  20. Risk Management in Lean Product Development

    E-Print Network [OSTI]

    Oehmen, Josef

    This whitepaper summarizes 15 years of research conducted at MIT's Lean Advancement Initiative on the topic of risk management in product design and development. It discusses current challenges in risk management for product ...

  1. More production buildings and expanded operations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    production buildings and expanded operations The oval shaped Alpha calutrons were designated "Alpha 1" design and were installed in Buildings 9201- 1, 9201-2, and 9201-3. Each...

  2. AVLIS production plant waste management plan

    SciTech Connect (OSTI)

    Not Available

    1984-11-15T23:59:59.000Z

    Following the executive summary, this document contains the following: (1) waste management facilities design objectives; (2) AVLIS production plant wastes; (3) waste management design criteria; (4) waste management plan description; and (5) waste management plan implementation. 17 figures, 18 tables.

  3. Continuous production of conducting polymer

    E-Print Network [OSTI]

    Gaige, Terry A. (Terry Alden), 1981-

    2004-01-01T23:59:59.000Z

    A device to continuously produce polypyrrole was designed, manufactured, and tested. Polypyrrole is a conducting polymer which has potential artificial muscle applications. The objective of continuous production was to ...

  4. Design Squad seasons 1 and 2 : an engineering perspective

    E-Print Network [OSTI]

    Powers, Benjamin G. (Benjamin George), 1980-

    2008-01-01T23:59:59.000Z

    This thesis describes the engineering tasks associated with production of Design Squad, a reality-based television program on WGBH. In Design Squad a client gives two teams of high school students an engineering design ...

  5. Builders of the vision : technology and the imagination of design

    E-Print Network [OSTI]

    Cardoso Llach, Daniel

    2012-01-01T23:59:59.000Z

    This dissertation identifies and documents a "technological imagination of design" emerging around the reconfigured discourses of design and design representation by the culture of technology production in the Computer-Aided ...

  6. Renewable Energy Case Studies | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    from FEMP and local utility rebates. U.S. Fish and Wildlife Service, Shepherdstown, West Virginia: Center designed to use passive solar and low-energy technologies that are...

  7. National Aeronautics and Space Administration www.nasa.gov

    E-Print Network [OSTI]

    Waliser, Duane E.

    or Federal Energy Management Program (FEMP)-designated Electronic Stewardship GOAL: Procure energy important actions for Federal Agencies (NASA has accomplished all): · DesignateanAgency competition between occupants of different buildings. Powering Our Buildings With More Renewable Energy

  8. Technical Assistance Guide: Working with DOE National Laboratories (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2012-07-01T23:59:59.000Z

    A fact sheet that provides an overview of FEMP's technical assistance through the Department of Energy's National Laboratories. The Federal Energy Management Program (FEMP) facilitates the Federal Government's implementation of sound, cost-effective energy management and investment practices to enhance the nation's energy security and environmental stewardship. To advance that mission, FEMP fosters collaboration between Federal agencies and U.S. Department of Energy (DOE) national laboratories. This guide outlines technical assistance capabilities and expertise at DOE national laboratories. Any laboratory assistance must be in accordance with Federal Acquisition Regulation (FAR) Subpart 35.017 requirements and the laboratory's designation as Federal Funded Research and Development Center (FFRDC) facilities.

  9. Productivity improvement for longwall development

    SciTech Connect (OSTI)

    Whipkey, K. [Norwest, Ashland, KY (United States)

    2005-08-01T23:59:59.000Z

    Industry survey reveals coal operators thoughts about the use of different techniques to keep development ahead of longwall production. Factors considered that can optimise productivity include mine design (the number of entries, size of pillars etc.), work schedules, preventative maintenance programs and good management. The article was adapted from a presentation to Longwall USA 2005, in June 2005 (Pittsburgh, PA, USA). 3 figs.

  10. Visualising Early Product Development Information

    E-Print Network [OSTI]

    Salustri, Filippo A.

    screws store energy Electricity Supply Screw User Force couple screw & PSD Installed Screw Waste Energy System Bit Bit Screw Screw Electricity Supply Waste Energy User Force Activation System User Input Architecture Systems Design Design Schematics for visualisation of early product information Light

  11. MESA Products, Inc. MESA Products, Inc. is a small, privately held business

    E-Print Network [OSTI]

    Magee, Joseph W.

    MESA Products, Inc. MESA Products, Inc. is a small, privately held business that designs in underground and submerged structures, such as pipelines and tanks. MESA sells products and materials and production facility are based in Tulsa, Okla.; branch offices are in Houston, Texas; Tallahassee, Fla

  12. Kamal Kapadia DRAFT Productive Uses of Renewables

    E-Print Network [OSTI]

    Kammen, Daniel M.

    ) ................................................. 13 China: Passive Solar Heating for Rural Health Clinics (China PSHRHC)......................... 13?............................................................................... 4 DESIGNING AND IMPLEMENTING RENEWABLE ENERGY PROJECTS WITH PRODUCTIVE USE COMPONENTS: ANALYSIS the productive uses of energy is an important aspect in the design and implementation of rural energy projects

  13. Evolution of Energy Efficiency Programs Over Time: The Case of Standby Power

    SciTech Connect (OSTI)

    Payne, Christopher; Chung, Iris (Hoi); Fisher, Emily

    2014-08-17T23:59:59.000Z

    Issued in 2001, Presidential Executive Order 13221 directed federal agencies to purchase products with low standby power, with the goal of 1) reducing energy consumption in federal facilities, and 2) drawing attention to the problem of high standby power consumption, with guidance provided by the Federal Energy Management Program (FEMP). At that time, standby power was newly recognized as an increasing building energy load. Since then, procurement of products with low standby power have been set in place in acquisition processes, and the purchasing power of the federal government continues to influence manufacturers design decisions related to standby power. In recent years, FEMP has shifted effort from direct manufacturer outreach for data collection, to integrating low standby requirement into broader acquisition programs including Energy Star and Electronic Product Environmental Assessment Tool (EPEAT). Another milestone has been the labeling of low standby products on the GSA Advantage website to simplify and enhance compliance. Looking forward into the program?s future, this question arises How do we design programs over time to reflect market and technology changes, by adjusting programmatic requirements while maintaining effectiveness? This paper discusses that question for the case of standby power, which transitioned from covering a single to multiple environmental attributes, both in the context of the program's past and future.

  14. INTERNATIONAL CONFERENCE ON ENGINEERING DESIGN ICED 03 STOCKHOLM, AUGUST 19-21, 2003

    E-Print Network [OSTI]

    Agogino, Alice M.

    teams, product design lifecycle, latent semantic analysis, coherence 1 Introduction Engineering design-world context in which the design concepts evolve in the product design lifecycle. They reflect the conflicting artefact. They convey the value the product will bring to the people who will use it. They capture the real

  15. Product Demonstrations

    Broader source: Energy.gov [DOE]

    The Consortium will pursue a number of demonstrations following the general procedure used by DOE's GATEWAY demonstration program. Specific products to be featured in a demonstration may be...

  16. Properly Evaluating load-following products

    SciTech Connect (OSTI)

    Cavicchi, Joseph; Lemon, Andrew

    2009-01-15T23:59:59.000Z

    The authors briefly survey the jurisdictions where load-following products have been successfully used, examine the characteristics of the load-following products, and explain the shortcomings and inaccurate conclusions of previous analyses. A more thorough analysis reveals that the load-following products fulfill the public policy objectives for which they have been designed and do not adversely impact wholesale electricity markets.

  17. Leading by Example with Smart Energy Management (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2008-12-01T23:59:59.000Z

    The Federal Energy Management Program facilitates the Federal Government?s implementation of sound, cost-effective energy management and investment practices to enhance the nation?s energy security and environmental stewardship. FEMP does this by focusing on the needs of its Federal customers, delivering an array of products grouped into project transaction services, applied technology services, and decision support services. This document outlines FEMP services and programs.

  18. 2001 ''You Have the Power'' campaign [Federal Energy Management Program]. Final technical report

    SciTech Connect (OSTI)

    NONE

    2002-01-01T23:59:59.000Z

    The Tasks of 2001 ''You Have the Power'' campaign by the Federal Energy Management Program (FEMP) are: Task 1--Interagency Planning Meetings; Task 2--Ear Day Event; Task 3--Earth Day and Energy Awareness Month Activities; Task 4--Regional Target; Task 5--Outreach Tools and Campaign Products; Task 6--Private Sector Participation; Task 7--''You Have the Power'' on the FEMP Web Site; and Task 8--Effective Communications.

  19. Vice Chancellor's PhD Scholarships School of Architecture, Design and the Built Environment

    E-Print Network [OSTI]

    Evans, Paul

    to reduce the products' impact on the environment prior to other stages of product lifecycle. To meet and tools supporting sustainable development of products at all stages of product lifecycle; closely work Advanced Design and Manufacturing Engineering Research Group Sustainable Product Design Background

  20. Human-Centered Sustainable Product !!Environmental impact

    E-Print Network [OSTI]

    Agogino, Alice M.

    Human-Centered Sustainable Product Design !!Environmental impact of buildings !!Green Building environments for people What is "Green" Building Design ? Real Goods Solar Living Center, Hopland, CA Van der Ryn Associates Gail Brager, School of Environmental Design ·! 36% of total U.S. primary energy use

  1. Max Tech and Beyond: Maximizing Appliance and Equipment Efficiency by Design

    E-Print Network [OSTI]

    Desroches, Louis-Benoit

    2012-01-01T23:59:59.000Z

    Primary Energy Use (quads) Product Ultra-Efficient Designefficient design options found to have significant energy-efficient design options include power supplies that involve fewer energy

  2. Geometric Qualification of Production Parts

    SciTech Connect (OSTI)

    J. A. Bradley

    2005-09-30T23:59:59.000Z

    Computer Aided Design (CAD) is a commonly utilized software tool to conceptualize and create the part designs that are then used as input for product definition, or for the manufacture of production parts within commercial industry and, more specifically, at the Kansas City Plant (KCP). However, data created on CAD systems is, at times, unable to regenerate within the originating CAD system or be shared or translated for use by a dissimilar CAD system. Commercial software has been developed to help identify or qualify these difficulties that occur in the usage of this data. This project reviewed the different commercial software packages available for the activity of qualification and made recommendations for availability and use in the design processes at the KCP prior to the release of the product definition.

  3. Memorable Logo Design

    E-Print Network [OSTI]

    Lampe, Lori

    2011-08-08T23:59:59.000Z

    of the favored faded blue color come from the Royal Navy. Naval uniforms were dyed blue and ultimately, ?a sailor?s length of service could be read by how faded his uniform had become? (Peterson, 2000). Therefore, young recruits didn?t 13 want to look even... of design that greatly influences customer?s perceptions of the company or product. Think of particular businesses that have a distinct color that defines them: the golden arches of McDonalds, red Coca-Cola label, or blue AT&T globe. ?In 8 each...

  4. An Evaluation of the Federal Energy Management Program Technical Assistance Workshops: Results of a 1998 Customer Survey

    SciTech Connect (OSTI)

    G. B. Gordon; N. Hall

    1999-04-01T23:59:59.000Z

    This report presents the results of a customer telephone survey of the participants of six workshops provided by the U. S. Department of Energy Federal Energy Management Program (FEMP) during calendar years 1995 and 1996. The primary purpose for the survey was to provide the Team Leader for FEMP Technical Assistance and members of the team with detailed customer feedback pertaining to how well selected FEMP workshops are doing and to identify areas for improvement. The information presented enables managers to see both the strengths of their workshops, as well as workshop components that can be improved. In addition, the report identifies the questions included in the survey that were the most productive for obtaining customers experiences, opinions and recommendations. The experiences gained during this survey provide a platform from which to launch an annual FEMP customer survey.

  5. SAVEnergy Action Plans: Implementing audits in federal facilities

    SciTech Connect (OSTI)

    Mayo, K H

    1994-07-01T23:59:59.000Z

    The Department of Energy`s Federal Energy Management Program is charged with implementing key sections of the Energy Policy Act of 1992 and all of the Executive Order 12902, to make the Federal Government operate more energy and water efficient. A congressionally-mandated energy, renewables, and water conservation audit program is one component of this plan. The SAVEnergy Action Plan is designed to help energy managers identify specific energy and water projects and link these projects to appropriate funding mechanisms for implementation. FEMP`s SAVEnergy staff has been working with Federal agencies to develop strategies to complete their legislatively-mandated goals, both through FEMP`s programs and other programs available to the Federal sector.

  6. Hydrogen Production

    Fuel Cell Technologies Publication and Product Library (EERE)

    This 2-page fact sheet provides a brief introduction to hydrogen production technologies. Intended for a non-technical audience, it explains how different resources and processes can be used to produ

  7. RMOTC - Production

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    on maximizing the value of the NPR-3 site and will continue with its Production Optimization Projects. NPR-3 includes 9,481 acres with more than 400 oil-producing wells....

  8. Designer Cosmology

    E-Print Network [OSTI]

    Bruce A. Bassett; David Parkinson; Robert C. Nichol

    2005-07-05T23:59:59.000Z

    We highlight the flexibility of the IPSO experiment-design framework by contrasting its application to CMB, weak lensing and redshift surveys. We illustrate the latter with a 10 parameter MCMC D-optimisation of a dark energy redshift survey. When averaged over a standard dark energy model space the resulting optimal survey typically has only one or two redshift bins, located at zoptimisation we show how the statistical power of such surveys is significantly enhanced. Experiment design is aided by the richness of the figure of merit landscape which means one can impose secondary optimisation criteria at little cost. For example, one may choose either to maximally test a single model (such as \\Lambda CDM) or to get the most general model-independent constraints possible (e.g. on a whole space of dark energy models). Such freedom points to a future where cosmological experiments become increasingly specialised and optimisation increasingly important.

  9. Essays on dynamic games and mechanism design

    E-Print Network [OSTI]

    Lang, Ruitian

    2014-01-01T23:59:59.000Z

    The dissertation considers three topics in dynamic games and mechanism design. In both problems, asymmetric information causes inefficiency in production and allocation. The first chapter considers the inefficiency from ...

  10. User experience design of complex systems

    E-Print Network [OSTI]

    Reily, Todd R. (Todd Richard)

    2012-01-01T23:59:59.000Z

    Over recent years, the global marketplace and its consumers have developed a mutual recognition for the rising prominence of design that delivers high quality user experience. For the provider of products and services, ...

  11. Designing for cost In an aerospace company

    E-Print Network [OSTI]

    Hammar, Elizabeth (Elizabeth Deming)

    2014-01-01T23:59:59.000Z

    Companies take different approaches, and achieve different degrees of implementation, in designing products for cost. This thesis discusses Target Costing and its application at The Boeing Company. Target Costing is a ...

  12. Designing a supply chain for a foreign Greenfield facility

    E-Print Network [OSTI]

    Anstey, Brian (Brian Mark), II

    2009-01-01T23:59:59.000Z

    ABB Schweiz AG has experienced substantial growth in demand for the innovative energy management and conversion products designed and assembled by the Medium Voltage Automation Products Division. This demand has fully ...

  13. Geotextiles, one among the different geosynthetic products, can be used for a number of functions or applications in pavement design. Specifically, woven or nonwoven geotextiles have been used in pavements to fulfill the

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    or applications in pavement design. Specifically, woven or nonwoven geotextiles have been used in pavements of geotextile and its location within the pavement system. The benefits of using geotextiles in pavements for more cost-effective pavements are probably being missed by not using (or by incorrectly using

  14. Assembly Design and Evaluation in an Augmented Reality Environment

    E-Print Network [OSTI]

    Pang, Y.

    The technologies and methodologies of assembly design and evaluation in the early design stage are highly significant to product development. This paper looks at a promising technology to mix real components (e.g. physical ...

  15. Automated Inclusive Design Heuristics Generation with Graph Mining

    E-Print Network [OSTI]

    Sangelkar, Shraddha Chandrakant

    2013-08-01T23:59:59.000Z

    Inclusive design is a concept intended to promote the development of products and environments equally usable by all users, irrespective of their age or ability. This research focuses on developing a method to derive heuristics for inclusive design...

  16. Building America Whole-House Solutions for New Homes: HVAC Design...

    Energy Savers [EERE]

    HVAC Design Strategy for a Hot-Humid Production Builder Building America Whole-House Solutions for New Homes: HVAC Design Strategy for a Hot-Humid Production Builder In this...

  17. Exploring a capability-demand interaction model for inclusive design evaluation

    E-Print Network [OSTI]

    Persad, Umesh

    2012-03-06T23:59:59.000Z

    of supporting analytical design evaluation for Inclusive Design. The analytical evaluation process involves evaluating products with user data rather than testing with actual users. The work focuses on the exploration of a capability-demand model of product...

  18. Abstract: Design and Demonstration of an Advanced Agricultural...

    Energy Savers [EERE]

    of an Advanced Agricultural Feedstock Supply System for Lignocellulosic Bioenergy Production Abstract: Design and Demonstration of an Advanced Agricultural Feedstock Supply...

  19. Analytical techniques of quality and cost : robust design, design of experiments, and the prediction of mean shift

    E-Print Network [OSTI]

    Ruflin, Justin, 1981-

    2004-01-01T23:59:59.000Z

    The quality of a product to a large extent determines the success of that product in competitive markets. Measuring and improving quality is thus a primary objective of the designer. The aim of the following work is to ...

  20. Design package for vacuum wand for fuel retrieval system

    SciTech Connect (OSTI)

    ROACH, H.L.

    1999-07-28T23:59:59.000Z

    This is a design package that contains the details for the design, fabrication, and testing of a vacuum wand that will pick up sludge and corrosion products generated during fuel assembly handling operations at K-Basin. This document contains requirements, development design information, design calculations, tests, and test reports.