Powered by Deep Web Technologies
Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Acceptance test procedure MICON software exhaust fan control modifications  

Science Conference Proceedings (OSTI)

This acceptance test verifies the MICON program changes for the new automatic transfer switch ATS-2 alarms, the Closed Loop Cooling isolator status, the CB-3 position alarm, and the alarms for the new emergency fan damper backup air compressor.

SILVAN, G.R.

1999-05-21T23:59:59.000Z

2

EVALUATION OF TRANSITIONS FOR TESTING AGRICULTURAL VENTILATION FANS WITH THE FAN ASSESSMENT NUMERATION SYSTEM (FANS).  

E-Print Network (OSTI)

??The Fan Assessment Numeration System (FANS) is an improved air velocity traverse method for measuring in situ fan performance. The FANS has been widely used,… (more)

Lopes, Igor Moreira

2012-01-01T23:59:59.000Z

3

INFLUENCE OF FAN OPERATION ON FAN ASSESSMENT NUMERATION SYSTEM (FANS) TEST RESULTS.  

E-Print Network (OSTI)

??The use of velocity traverses to measure in-situ air flow rate of ventilation fans can be subject to significant errors. The Fan Assessment Numeration System… (more)

Morello, Gabriela Munhoz

2011-01-01T23:59:59.000Z

4

Standards and Test Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards and Test Procedures Standards and Test Procedures Standards and Test Procedures The Department of Energy (DOE) establishes energy efficiency standards for certain appliances and equipment, and currently covers more than 50 different products. Authority to undertake this effort was granted by Congress, and DOE follows a four phase process when reviewing existing and developing new standards. Each Product page provides information on recent updates, current standards and test procedures, waivers, exceptions, and exemptions, statutory authority, and historical information. For information on current Rulemakings, visit Current Rulemaking and Notices. Consumer Products Battery Chargers and External Power Supplies Ceiling Fans Central Air Conditioners and Heat Pumps Clothes Dryers

5

Developing a Standard Test Method for Characterizing Fan-filter...  

NLE Websites -- All DOE Office Websites (Extended Search)

Developing a Standard Test Method for Characterizing Fan-filter Units Used in Industries Speaker(s): Tim Xu Date: July 21, 2008 - 12:00pm Location: 90-3122 Seminar HostPoint of...

6

Toward green systems for cleanrooms: Energy efficient fan-filter units  

E-Print Network (OSTI)

M. and F. Tsau. 2002. Fan-Filter Unit (FFU) Test Procedures.Laboratory Methods of Testing Fans for Rating, Air MovementTest Procedure For Fan-Filter Units (not published). [6] Xu,

Jeng, Ming-Shan; Xu, Tengfang; Lan, Chao-Ho

2004-01-01T23:59:59.000Z

7

Acceptance test report MICON software exhaust fan control modifications  

Science Conference Proceedings (OSTI)

This report documents the results the acceptance test HNF-4108 which verifies the MICON program changes for the new automatic transfer switch ATS-2 alarms, the Closed Loop Cooling isolator status, the CB-3 position alarm, the alarms for the new emergency fan damper backup air compressor, and the generator sequencer logic.

SILVAN, G.R.

1999-05-20T23:59:59.000Z

8

Current Test Procedure Waivers  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of Energy's (DOE) regulations for covered products permit a person to seek a waiver, or an interim waiver, from the test procedure requirements for covered appliances and...

9

Laboratory evaluation of fan/filter units' aerodynamic and energy performance  

E-Print Network (OSTI)

Jeng, M.S. , F. Tsau. 2002. Fan-Filter Unit (FFU) TestLaboratory Methods of Testing Fans for Rating, Air MovementTest Procedure For Fan-Filter Units (not published). Xu,

Xu, Tengfang; Jeng, Ming-Shan

2004-01-01T23:59:59.000Z

10

Rough Ride Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

NTP005 NTP005 Revision 2 Effective December 1, 2004 Electric Vehicle Rough Road Course Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date:__________ Ryan Harkins Approved by: _________________________________________________ Date: _______________ Donald B. Karner ©2004 Electric Transportation Applications All Rights Reserved Procedure ETA-NTP005 Revision 2 2 TABLE OF CONTENTS 1.0 Objectives 3 2.0 Purpose 3 3.0 Documentation 3 4.0 Initial Conditions and Prerequisites 4 5.0 Testing Activity Requirements 6 6.0 Glossary 12 7.0 References 14 Appendices Appendix A - Electric Vehicle Rough Road Test Data Sheet 15

11

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

E-Print Network (OSTI)

precluded testing the fan based on design data. Since thisStatic Pressure (inWg) fan CFM SF-SP SF-SP-Design-Sim time (supply fan pressure rise) SF- DP SF-DP-Design-simulated D.

Xu, Peng; Haves, Philip

2002-01-01T23:59:59.000Z

12

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

E-Print Network (OSTI)

measurement of airflow rate. Supply fan speed (0-1) SA S.A.Supply Fan test S.B.Fan pressure rise calibration SF-DP-Simulated Pressure

Xu, Peng; Haves, Philip

2002-01-01T23:59:59.000Z

13

NIST Test Fans the Flames for High-Rise Fire Safety  

Science Conference Proceedings (OSTI)

... Once the fires were under way, a variety of ventilation tests were conducted. For example, in one test, a large fan was placed at the front door to ...

2012-12-17T23:59:59.000Z

14

Optimum Statistical Test Procedure  

E-Print Network (OSTI)

In this paper we obtain a test which minimizes the sum of the two error probabilities irrespective of whether $\\sigma^2$ is known or unknown.

Rajesh Singh; Jayant Singh; Florentin Smarandache

2009-04-10T23:59:59.000Z

15

Fan Aerodynamic Performance Guarantees: Do Your Policies, Procedures and Penalties Provide Adequate Certainty?  

E-Print Network (OSTI)

With few exceptions, fan vendors do not provide a written guarantee regarding aerodynamic performance. Some fan vendors even go so far as to state in their terms and conditions of sale that fan performance is not guaranteed unless it is specifically reque

Kaufman, S. G.; Martin, V.; Falk, M. A.

2004-01-01T23:59:59.000Z

16

MITG test procedure and results  

DOE Green Energy (OSTI)

Elements and modules for Radioisotope Thermoelectric Generator have been performance tested since the inception of the RTG program. These test articles seldom resembled flight hardware and often lacked adequate diagnostic instrumentation. Because of this, performance problems were not identified in the early stage of program development. The lack of test data in an unexpected area often hampered the development of a problem solution. A procedure for conducting the MITG Test was developed in an effort to obtain data in a systematic, unambiguous manner. This procedure required the development of extensive data acquisition software and test automation. The development of a facility to implement the test procedure, the facility hardware and software requirements, and the results of the MITG testing are the subject of this paper.

Eck, M.B.; Mukunda, M.

1983-01-01T23:59:59.000Z

17

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

6 6 Revision 2 Effective October 1, 2007 Braking Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date: _________ Roberta Brayer Approved by: _________________________________________________ Date: _______________ Donald Karner Procedure ETA-HTP06 Revision 2 i TABLE OF CONTENTS 1. Objectives 1 2. Purpose 1 3. Documentation 1 4. Initial Conditions and Prerequisites 1 5. Testing Activity Requirements 3 5.3 Dry Controlled Test 4 6. Glossary 5 7. References 7 Appendices Appendix A - Handling Pad Test Data Sheet 8

18

Building Technologies Office: Current Test Procedure Waivers  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedure Test Procedure Waivers to someone by E-mail Share Building Technologies Office: Current Test Procedure Waivers on Facebook Tweet about Building Technologies Office: Current Test Procedure Waivers on Twitter Bookmark Building Technologies Office: Current Test Procedure Waivers on Google Bookmark Building Technologies Office: Current Test Procedure Waivers on Delicious Rank Building Technologies Office: Current Test Procedure Waivers on Digg Find More places to share Building Technologies Office: Current Test Procedure Waivers on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement Rulemakings & Notices Current Rulemakings & Notices Test Procedure Waivers Recent Federal Register Notices How to Participate or Comment

19

Inspection system performance test procedure  

SciTech Connect

This procedure establishes requirements to administer a performance demonstration test. The test is to demonstrate that the double-shell tank inspection system (DSTIS) supplied by the contractor performs in accordance with the WHC-S-4108, Double-Shell Tank Ultrasonic Inspection Performance Specification, Rev. 2-A, January, 1995. The inspection system is intended to provide ultrasonic (UT) and visual data to determine integrity of the Westinghouse Hanford Company (WHC) site underground waste tanks. The robotic inspection system consists of the following major sub-systems (modules) and components: Mobile control center; Deployment module; Cable management assembly; Robot mechanism; Ultrasonic testing system; Visual testing system; Pneumatic system; Electrical system; and Control system.

Jensen, C.E.

1995-01-17T23:59:59.000Z

20

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

4 4 Revision 1 Effective June 2008 Electromagnetic Interference and Susceptibility Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date:__________ Garrett P. Beauregard Approved by: ______________________________________________ Date: _______________ Donald B. Karner Procedure ETA-GTP004 Revision 1 2 Table of Contents 1 Objective ..................................................................................................................... 3 2 Purpose........................................................................................................................ 3 3 Documentation............................................................................................................

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

3 3 Revision 1 Effective June 2008 Battery Capacity and Depth of Discharge Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date:__________ Garrett P. Beauregard Approved by: ______________________________________________ Date: _______________ Donald B. Karner Procedure ETA-GTP003 Revision 1 2 Table of Contents 1 Objective ..................................................................................................................... 3 2 Purpose........................................................................................................................ 3 3 Documentation............................................................................................................

22

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

2 2 Revision 1 Effective June 2008 Traction System Test Prepared by Electric Transportation Applications Prepared by: _______________________________ Date:__________ Garrett P. Beauregard Approved by: ______________________________________________ Date: _______________ Donald B. Karner Procedure ETA-GTP002 Revision 1 2 Table of Contents 1 Objective ..................................................................................................................... 3 2 Purpose........................................................................................................................ 3 3 Documentation............................................................................................................

23

Record of Communication Concerning Ceiling Fan and Ceiling Fan Light Kit Framework Document—Docket No. EERE-2012-BT-STD-0045  

Energy.gov (U.S. Department of Energy (DOE))

This memo provides an overview of communications made to DOE staff on the subject of possible changes to standards and test procedures for ceiling fans and ceiling fan light kits.

24

Building Technologies Office: Standards and Test Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Standards and Test Standards and Test Procedures to someone by E-mail Share Building Technologies Office: Standards and Test Procedures on Facebook Tweet about Building Technologies Office: Standards and Test Procedures on Twitter Bookmark Building Technologies Office: Standards and Test Procedures on Google Bookmark Building Technologies Office: Standards and Test Procedures on Delicious Rank Building Technologies Office: Standards and Test Procedures on Digg Find More places to share Building Technologies Office: Standards and Test Procedures on AddThis.com... About Standards & Test Procedures Implementation, Certification & Enforcement Rulemakings & Notices Further Guidance ENERGY STAR® Popular Links Success Stories Previous Next Lighten Energy Loads with System Design. Learn More.

25

Building Technologies Office: Test Procedure Development and...  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedure Development and Revision to someone by E-mail Share Building Technologies Office: Test Procedure Development and Revision on Facebook Tweet about Building...

26

Building Technologies Office: Test Procedure Waivers  

NLE Websites -- All DOE Office Websites (Extended Search)

Waivers on Twitter Bookmark Building Technologies Office: Test Procedure Waivers on Google Bookmark Building Technologies Office: Test Procedure Waivers on Delicious Rank...

27

Software Verification and Validation Test Report for the HEPA filter Differential Pressure Fan Interlock System  

Science Conference Proceedings (OSTI)

The HEPA Filter Differential Pressure Fan Interlock System PLC ladder logic software was tested using a Software Verification and Validation (V&V) Test Plan as required by the ''Computer Software Quality Assurance Requirements''. The purpose of his document is to report on the results of the software qualification.

ERMI, A.M.

2000-09-05T23:59:59.000Z

28

Development of a Fan-Filter Unit Test Standard, Laboratory Validations, and its Applications across Industries  

E-Print Network (OSTI)

Energy Performance of Fan-Filter Units, Version 1.3 (2005).Energy Performance of Fan-Filter Units, Version 2.0 (2006).Evaluation of Fan-filter Units’ Aerodynamic and Energy

Xu, Tengfang

2008-01-01T23:59:59.000Z

29

Development of a Fan-Filter Unit Test Standard, Laboratory Validations, and its Applications across Industries  

E-Print Network (OSTI)

Energy Performance of Fan-Filter Units, Version 1.3 (2005).Energy Performance of Fan-Filter Units, Version 2.0 (2006).Laboratory Evaluation of Fan-filter Units’ Aerodynamic and

Xu, Tengfang

2008-01-01T23:59:59.000Z

30

Test Procedure Waivers | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Appliance & Equipment Standards » Rulemakings & Notices » Test Appliance & Equipment Standards » Rulemakings & Notices » Test Procedure Waivers Test Procedure Waivers Products covered by standards change as manufacturers add new features to their products and update designs in order to compete for consumers. Innovation and product development occasionally causes products to change in ways that either (1) make the results of a test procedure unrepresentative of actual energy use or efficiency, or (2) make it impossible to test in accordance with the relevant test procedure. For this reason, the Department of Energy (DOE) considers petitions for waivers from test procedures under certain circumstances. In general, any interested party-typically a manufacturer-may submit a petition for a test procedure waiver for a basic model of a covered product

31

A general design for energy test procedures  

SciTech Connect

Appliances are increasingly controlled by microprocessors. Unfortunately, energy test procedures have not been modified to capture the positive and negative contributions of the microprocessor to the appliance's energy use. A new test procedure is described which captures both the mechanical and logical features present in many new appliances. We developed an energy test procedure for refrigerators that incorporates most aspects of the proposed new approach. Some of the strengths and weaknesses of the new test are described.

Meier, Alan

2000-06-15T23:59:59.000Z

32

Building Technologies Office: Current Test Procedure Waivers  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedure Waivers Test Procedure Waivers The U.S. Department of Energy's (DOE) regulations for covered products permit a person to seek a waiver, or an interim waiver, from the test procedure requirements for covered appliances and commercial equipment if certain criteria are satisfied. Regulations applicable to test procedure waivers for appliances can be found at 10 CFR 430.27; those applicable to test procedure waivers for commercial equipment are at 10 CFR 431.401. This table lists all waivers to test procedures that DOE has granted and that are still in effect. The links to the notices provide access to the dockets in Regulations.gov, which contain all notices and public comments. For more information, please email: AS_Waiver_Requests@ee.doe.gov The links to the notices provides access to the docket in regulations.gov, which contains all notices and public comments.

33

EV America Skid Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

6 Revision 3 Effective February 1, 2008 Braking Test Prepared by Electric Transportation Applications Prepared by: Date: Derek Peterson...

34

Design, testing and two-dimensional flow modeling of a multiple-disk fan  

Science Conference Proceedings (OSTI)

A multiple-disk Tesla type fan has been designed, tested and analyzed two-dimensionally using the conservation of angular momentum principle. Experimental results showed that such multiple-disk fans exhibited exceptionally low performance characteristics, which could be attributed to the low viscosity, tangential nature of the flow, and large mechanical energy losses at both suction and discharge sections that are comparable to the total input power. By means of theoretical analysis, local and overall shearing stresses on the disk surfaces have been determined based on tangential and radial velocity distributions of the air flow of different volume flow rates at prescribed disk spaces and rotational speeds. Then the total power transmitted by rotating disks to air flow, and the power acquired by the air flow in the gap due to transfer of angular momentum have been obtained by numerically integrating shearing stresses over the disk surfaces. Using the measured shaft and hydraulic powers, these quantities were utilized to evaluate mechanical energy losses associated with the suction and discharge sections of the fan. (author)

Engin, Tahsin; Oezdemir, Mustafa; Cesmeci, Sevki [Department of Mechanical Engineering, The University of Sakarya, Esentepe Campus, 54187 Sakarya (Turkey)

2009-11-15T23:59:59.000Z

35

Building Technologies Office: Standards and Test Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

icon Public Meetings & Comment Deadlines Newsletter Recent Federal Register Notices Standards and Test Procedures The Department of Energy (DOE) establishes energy efficiency...

36

Fan Energy Savings Decisions  

E-Print Network (OSTI)

Axial fans are used for thousands of industrial applications consuming millions of kilowatts daily. The decision that saves dollars is to either automatically change fan speed or change blade pitch to save up to 50 percent of consumed power over a fixed pitch, constant speed fan. A discussion of the merits of each type is presented with actual test results.

Monroe, R. C.

1985-05-01T23:59:59.000Z

37

Void fraction instrument acceptance test procedure  

DOE Green Energy (OSTI)

This acceptance test procedure (ATP) was written to test the void fraction instrument (VFI) and verify that the unit is ready for field service. The procedure verifies that the mechanical and electrical features (not specifically addressed in the software ATP) and software alarms are operating as designed.

Pearce, K.L.

1994-09-15T23:59:59.000Z

38

Nitrogen chiller acceptance test procedure  

SciTech Connect

This document includes the inspection and testing requirements for the Nitrogen Chiller unit. The Chiller will support the Rotary Mode core Sampling System during the summer. The Chiller cools the Nitrogen Purge Gas that is used when drilling in tank wastes to cool the drill bit.

Kostelnik, A.J.

1995-03-07T23:59:59.000Z

39

Workshop on Test Procedures for Materials for Hydrogen ...  

Science Conference Proceedings (OSTI)

Test Procedures for Hydrogen Pipelines. ... The NIST Workshop on Materials Test Procedures for Hydrogen Pipelines Proceedings is now available. ...

40

AZ-101 Mixer Pump Test Qualification Test Procedures (QTP)  

SciTech Connect

Describes the Qualification test procedure for the AZ-101 Mixer Pump Data Acquisition System (DAS). The purpose of this Qualification Test Procedure (QTP) is to confirm that the AZ-101 Mixer Pump System has been properly programmed and hardware configured correctly. This QTP will test the software setpoints for the alarms and also check the wiring configuration from the SIMcart to the HMI. An Acceptance Test Procedure (ATP), similar to this QTP will be performed to test field devices and connections from the field.

THOMAS, W.K.

2000-01-10T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Biomonitoring test procedures and biological criteria  

SciTech Connect

The Water Environment Federation recently issued a special publication, Biomonitoring in the Water Environment. In this paper, the authors highlight the contents of the chapter 3, Biomonitoring Test Procedures, identify current trends in test procedures and introduce the concept of biological criteria (biocriteria). The book chapter (and this paper) focuses on freshwater and marine chronic and acute toxicity tests used in the National Pollutant Discharge Elimination System (NPDES) permits program to identify effluents and receiving waters containing toxic materials in acutely or chronically toxic concentrations. The two major categories of toxicity tests include acute tests and chronic tests. The USEPA chronic tests required in NPDEs permits have been shortened to 7 days by focusing on the most sensitive life-cycle stages; these tests are often referred to as short-term chronic tests. The type of test(s) required depend on NPDES permit requirements, objectives of the test, available resources, requirements of the test organisms, and effluent characteristics such as variability in flow or toxicity. The permit writer will determine the requirements for toxicity test(s) by considering such factors as dilution, effluent variability, and exposure variability. Whether the required test is acute or chronic, the objective of the test is to estimate the safe or no effect concentration which is defined as the concentration which will permit normal propagation of fish and other aquatic life in the receiving waters. In this paper, the authors review the types of toxicity tests, the commonly used test organisms, and the uses of toxicity test data. In addition, they briefly describe research on new methods and the use of biological criteria.

Kszos, L.A. [Oak Ridge National Lab., TN (United States); Lipschultz, M.J. [City of Las Vegas, NV (United States); Foster, W.E. [Saint Mary`s Coll., Winona, MN (United States)

1997-10-01T23:59:59.000Z

42

Acceptance test procedure for SY Tank Farm replacement exhauster unit  

SciTech Connect

The proper functioning of a new 241-SY Tank Farm replacement exhauster will be acceptance tested, to establish operability and to provide an operational baseline for the equipment. During this test, a verification of all of the alarm and control circuits associated with the exhaust, which provide operating controls and/or signals to local and remote alarm/annunciator panels, shall be performed. Test signals for sensors that provide alarms, warnings, and/or interlocks will be applied to verify that alarm, warning, and interlock setpoints are correct. Alarm and warning lights, controls, and local and remote readouts for the exhauster will be verified to be adequate for proper operation of the exhauster. Testing per this procedure shall be conducted in two phases. The first phase of testing, to verify alarm, warning, and interlock setpoints primarily, will be performed in the MO-566 Fab Shop. The second phase of testing, to verify proper operation and acceptable interface with other tank farm systems, will be conducted after the exhauster and all associated support and monitoring equipment have been installed in the SY Tank Farm. The exhauster, which is mounted on a skid and which will eventually be located in the SY tank farm, receives input signals from a variety of sensors mounted on the skid and associated equipment. These sensors provide information such as: exhauster system inlet vacuum pressure; prefilter and HEPA filter differential pressures; exhaust stack sampler status; exhaust fan status; system status (running/shut down); and radiation monitoring systems status. The output of these sensors is transmitted to the exhauster annunciator panel where the signals are displayed and monitored for out-of-specification conditions.

Becken, G.W.

1994-12-16T23:59:59.000Z

43

Building Technologies Office: ENERGY STAR Test Procedures and...  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedures and Verification to someone by E-mail Share Building Technologies Office: ENERGY STAR Test Procedures and Verification on Facebook Tweet about Building Technologies...

44

Meeting Concerning Potential Test Procedures and Energy Conservation...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Concerning Potential Test Procedures and Energy Conservation Standards for Set-Top Boxes and Network Equipment Meeting Concerning Potential Test Procedures and Energy Conservation...

45

Rui Fan  

NLE Websites -- All DOE Office Websites (Extended Search)

Rui Fan Rui Fan 1 Cyclotron Road MS 90-4000 Berkeley CA 94720 Office Location: 90-2087 (510) 486-6305 RFan@lbl.gov Vision & Mission Organization Awards Fellowship Staff Services...

46

Residential photovoltaic power conditioner subsystem test procedures  

DOE Green Energy (OSTI)

The inspections to be made, the conditions for measurement, the variables to be measured and the analyses to be performed in order to characterize the operation of a power-conditioning subsystem (PCS) are described. Of primary concern is the small, utility-interactive PCS in the 2- to 10-kW power range for use in a residential photovoltaic (PV) system feeding a single-phase 120/240-volt line. The procedure is broken down into four main tasks: analysis of the design, tests under nominal conditions, tests under extreme conditions, and accelerated environmental stress tests. The results of these tests will provide an objective assessment of PCS performance under the full range of conditions likely to be encountered in actual applications.

Cox, III, C. H.

1982-02-01T23:59:59.000Z

47

Fan Repair Guideline  

Science Conference Proceedings (OSTI)

The successful repair of a fan component is affected by a number of different factors. These include correctly assessing the root cause of failure, determining the best repair option, implementation of proper repair procedures, and compliance with applicable codes and standards. However, in many situations the proper solution is not clearly evident. The purpose of this document is to provide guidance in the area of induced draft / forced draft fan repair. Specifically, this document deals with the repair...

2002-08-15T23:59:59.000Z

48

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

SciTech Connect

An automated fault detection and diagnosis tool for HVAC systems is being developed, based on an integrated, life-cycle, approach to commissioning and performance monitoring. The tool uses component-level HVAC equipment models implemented in the SPARK equation-based simulation environment. The models are configured using design information and component manufacturers' data and then fine-tuned to match the actual performance of the equipment by using data measured during functional tests of the sort using in commissioning. This paper presents the results of field tests of mixing box and VAV fan system models in an experimental facility and a commercial office building. The models were found to be capable of representing the performance of correctly operating mixing box and VAV fan systems and detecting several types of incorrect operation.

Xu, Peng; Haves, Philip

2002-05-16T23:59:59.000Z

49

Test Procedure Development and Revision | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Test Procedure Development and Revision Test Procedure Development and Revision Test Procedure Development and Revision Most energy conservation standards rulemakings are accompanied by a concurrent test procedure rulemaking. Test procedures detail the protocols that manufacturers must follow when testing their products for compliance with Department of Energy (DOE) standards. DOE also uses the test procedures to determine compliance with the applicable standards in any verification or enforcement testing. The procedures specify how to measure and calculate the energy efficiency and/or energy use of each appliance. Test procedures also specify how to calculate an estimate of an appliance's annual operating cost, which is used on the EnergyGuide label as required by the Federal Trade Commission.

50

Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Fuel Economy Test Fuel Economy Test Procedures and Labeling to someone by E-mail Share Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Facebook Tweet about Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Twitter Bookmark Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Google Bookmark Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Delicious Rank Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on Digg Find More places to share Alternative Fuels Data Center: Fuel Economy Test Procedures and Labeling on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Fuel Economy Test Procedures and Labeling

51

An Innovative Method for Dynamic Characterization of Fan Filter Unit Operation.  

E-Print Network (OSTI)

Laboratory Methods of Testing Fans for Rating. ASHRAE. 1987.Efficient Filtration: Fan filter units. Final Report,Energy Performance of Fan Filter Units, Version 1.3. ”

Xu, Tengfang

2006-01-01T23:59:59.000Z

52

WRAP Trupact Loading System Operational Test Procedure  

Science Conference Proceedings (OSTI)

This procedure has been prepared to verify the TRUPACT System (TS) operates in accordance with system design and specifications.

DOSRAMOS, E.V.

1999-09-01T23:59:59.000Z

53

Alternative Fuels Data Center: Biodiesel Quality Testing Procedures  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Biodiesel Quality Biodiesel Quality Testing Procedures to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Twitter Bookmark Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Google Bookmark Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Delicious Rank Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on Digg Find More places to share Alternative Fuels Data Center: Biodiesel Quality Testing Procedures on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Biodiesel Quality Testing Procedures Each biodiesel or other renewable diesel producer, distributor, or importer

54

Common Information Model Meter Disconnect/Reconnect Interoperability Test Procedure  

Science Conference Proceedings (OSTI)

The Common Information Model (CIM) Disconnect/Reconnect Interoperability Test Procedure is one in a series of EPRI Interoperability Test Procedures (ETIPs) created by EPRI whose purpose is to thoroughly document the actors, interfaces, and test steps for the interoperability testing of specific parts of the International Electrotechnical Commission (IEC) Common Information Model (CIM) standard. The Test Procedures are initially being used for EPRI demonstration tests and are intended, over time, to form ...

2011-12-21T23:59:59.000Z

55

Common Information Model Meter Outage Nominal Interoperability Test Procedure  

Science Conference Proceedings (OSTI)

The CIM Meter Outage Nominal Interoperability Test Procedure is one in a series of EPRI CIM Interoperability Test Procedures (ETIPs) created by EPRI whose purpose is to thoroughly document the actors, interfaces, and test steps for the interoperability testing of specific parts of the International Electrotechnical Commission (IEC) Common Information Model (CIM) standard. The Test Procedures are initially being used for EPRI demonstration tests and are intended, over time, to form the basis of a set of C...

2011-12-16T23:59:59.000Z

56

Common Information Model On Demand Meter Read Interoperability Test Procedure  

Science Conference Proceedings (OSTI)

The Common Information Model (CIM) On Demand Meter Read Interoperability Test Procedure is one in a series of EPRI Interoperability Test Procedures (ETIPs) created by EPRI whose purpose is to thoroughly document the actors, interfaces, and test steps for the interoperability testing of specific parts of the International Electrotechnical Commission (IEC) Common Information Model (CIM) standard. The Test Procedures are initially being used for EPRI demonstration tests and are intended, over time, to form ...

2011-12-14T23:59:59.000Z

57

Common Information Model Meter Tamper Detection Interoperability Test Procedure  

Science Conference Proceedings (OSTI)

The Common Information Model (CIM) Meter Tamper Detection Interoperability Test Procedure is one in a series of EPRI Interoperability Test Procedures (ETIPs) created by EPRI whose purpose is to thoroughly document the actors, interfaces, and test steps for the interoperability testing of specific parts of the International Electrotechnical Commission (IEC) Common Information Model (CIM) standard. The Test Procedures are initially being used for EPRI demonstration tests and are intended, over time, to for...

2011-11-30T23:59:59.000Z

58

MIT validation probe acceptance test procedure  

SciTech Connect

As part of the Multi-Functional Instrument Trees (MITs) a Validation Probe is being fabricated by Los Alamos National Laboratories (LANL). The Validation Probe assembly is equipped with a Winch, depth counter, and a Resistance Temperature Detector (RTD) which will render a means for verifying the temperature readings of which will render a means for verifying the temperature readings of the MIT thermocouples. The purpose of this Acceptance Test Procedure (ATP) is to provide verification that the Validation Probe functions properly and accordingly to LANL design and specification. This ATP will be used for all Validation Probes procured from LANL. The ATP consists of a receiving inspection, RTD ambient temperature; RTD electrical failure, RTD insulation resistance, and accurate depth counter operation inspections. The Validation Probe is composed of an intank probe, a cable and winching system, and a riser extension (probe guide) which bolts onto the MIT. The validation`s thermal sensor is an RTD that is housed in a 0.062 inch diameter, magnesium oxide fill, 316 stainless steel tube. The sheath configuration provides a means for spring loading the sensor firmly against the validation tube`s inner wall. A 45 pound cylindrical body is connected above the sheath and is used as a force to lower the probe into the tank. This cylindrical body also provides the means to interconnect both electrically and mechanically to the winch system which lowers the probe to a specified location within the validation tube located in the tank.

Escamilla, S.A.

1994-08-23T23:59:59.000Z

59

Laboratory evaluation of fan/filter units' aerodynamic and energy performance  

E-Print Network (OSTI)

such as motor types, fan wheels, design, and orientations ofventilation system design, testing of fans and ventilation

Xu, Tengfang; Jeng, Ming-Shan

2004-01-01T23:59:59.000Z

60

702AZ aging waste ventilation facility year 2000 test procedure  

SciTech Connect

This test procedure was developed to determine if the 702AZ Tank Ventilation Facility system is Year 2000 Compliant. The procedure provides detailed instructions for performing the operations necessary and documenting the results. This verification procedure will document that the 702AZ Facility Systems are year 2000 compliant and will correctly meet the criteria established in this procedure.

Winkelman, W.D.

1998-07-22T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Fan Dai  

NLE Websites -- All DOE Office Websites (Extended Search)

Fan Dai Fan Dai China Energy Group Lawrence Berkeley National Laboratory 1 Cyclotron Road MS 90R2002 Berkeley CA 94720 Office Location: 90-2117S (510) 486-4000 FDai@lbl.gov Fan Dai is a Ph.D. Candidate in Environmental Policy at the College of Environmental Science and Forestry, State University of New York, and a LL.M. Candidate at Berkeley School of Law, University of California. Fan's research during her stay in LBNL's China Energy Group focuses on Energy Efficiency Governance, U.S.-China Clean Energy Partnership, the Carbon Cap-and-Trade Program in California and what China can learn from California's program. Prior to LBNL, she interned at the China National Center for Climate Change Strategy and International Cooperation (NCSC), China Youth Action Climate Network (CYCAN), and China State Forestry

62

FANS - Control  

Science Conference Proceedings (OSTI)

... If set to H+ and a magnet controller is connected, you are ... Typically motors 3, 4, 5, and 6 are fixed for FANS operation A fixed motor will not be ...

63

ZHAOSHENG FAN  

NLE Websites -- All DOE Office Websites (Extended Search)

ZHAOSHENG FAN Biosciences Division, Argonne National Laboratory, Argonne, IL 60439 Phone: (630) 252-1566; email: zfan@anl.gov EDUCATION Ph.D., Soil Physics, 2007, North Dakota...

64

Best Practice for Energy Efficient Cleanrooms: Fan-Filter Units  

E-Print Network (OSTI)

control F iltra ti on ? Fan Efficiency ? Right Sizing ?Energy Performance of Fan-Filte r Units, Version 1.3 (2005),RP36.1 (Draft). Testing Fan-Filter Units. Draft Recommended

Xu, Tengfang

2005-01-01T23:59:59.000Z

65

Museum Fan Downloads  

NLE Websites -- All DOE Office Websites (Extended Search)

Museum Fan Downloads Participate with us Participate Share your Stories Museum Fan Downloads invisible utility element Museum Fan Downloads Help the Bradbury Science Museum by...

66

DOE Issues Final Appliance Test Procedure Rule | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Appliance Test Procedure Rule Appliance Test Procedure Rule DOE Issues Final Appliance Test Procedure Rule December 8, 2006 - 9:46am Addthis WASHINGTON, DC - The U.S. Department of Energy (DOE) today announced a final rule establishing new test procedures and related definitions to determine the energy efficiency of certain residential appliances and commercial equipment. The rulemaking clarifies and codifies the test procedures mandated by the Energy Policy Act (EPAct) of 2005. "These new test procedures are the foundation for standards that will help bring more energy efficient options to the marketplace and result in energy savings for all Americans," said DOE Assistant Secretary for Energy Efficiency and Renewable Energy Andy Karsner. The final rulemaking, which appears in today's Federal Register, will

67

DOE Launches Public Test Procedure Guidance Website | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Launches Public Test Procedure Guidance Website Launches Public Test Procedure Guidance Website DOE Launches Public Test Procedure Guidance Website July 22, 2010 - 4:14pm Addthis The Department of Energy this week launched a new online database offering guidance on the Department's test procedures for appliances and commercial equipment. The new database will provide a publicly accessible forum for anyone with questions about -- or needing clarification of -- DOE's test procedures. This new online resource will also ensure that all manufacturers and members of the public are equally and immediately aware of the Department's interpretations of its test procedures. The database is available here. The database -- which is searchable by product category -- is designed to enable manufacturers, trade associations, and all other interested members

68

DOE Launches Public Test Procedure Guidance Website | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Public Test Procedure Guidance Website Public Test Procedure Guidance Website DOE Launches Public Test Procedure Guidance Website July 22, 2010 - 4:14pm Addthis The Department of Energy this week launched a new online database offering guidance on the Department's test procedures for appliances and commercial equipment. The new database will provide a publicly accessible forum for anyone with questions about -- or needing clarification of -- DOE's test procedures. This new online resource will also ensure that all manufacturers and members of the public are equally and immediately aware of the Department's interpretations of its test procedures. The database is available here. The database -- which is searchable by product category -- is designed to enable manufacturers, trade associations, and all other interested members

69

NFRC Test Procedure for Measuring the Steady-State  

E-Print Network (OSTI)

NFRC Test Procedure for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Adopted: March 15, 1991 Revised: April 17, 1997 Prepared by: Test Laboratory Task Group U Test Procedure for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Adopted

Massachusetts at Amherst, University of

70

Light duty utility arm equipment qualification test procedure  

SciTech Connect

The Equipment Qualification Test described in this test procedure document is the acceptance test procedure (ATP) for the LDUA Baseline System. It verifies that the equipment is complete and in working order, and demonstrates its readiness for being deployed into an actual underground storage tank.

Kiebel, G.R., Westinghouse Hanford

1996-07-22T23:59:59.000Z

71

Test Procedures for Faucets, Showerheads, Water Closets, Urinals...  

NLE Websites -- All DOE Office Websites (Extended Search)

Certain Commercial and Industrial Equipment: Test Procedures for Showerheads, Faucets, Water Closets, Urinals, and Commercial Prerinse Spray Valves AGENCY: Office of Energy...

72

Comparison of Test Procedures and Energy Efficiency Criteria...  

NLE Websites -- All DOE Office Websites (Extended Search)

International Standards & Labeling Programs for Copy Machines, External Power Supplies, LED Displays, Residential Gas Cooktops and Televisions Title Comparison of Test Procedures...

73

Test Procedure for §170.302 (p) Emergency Access  

Science Conference Proceedings (OSTI)

... September 24, 2010 1 Test Procedure for §170.302 (p) Emergency Access ... 170.302(p) Emergency Access. Permit authorized users ...

2013-11-06T23:59:59.000Z

74

Additional Guidance Regarding Application of Current Procedures for Testing  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Additional Guidance Regarding Application of Current Procedures for Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of Clothes Washers with Warm Rinse Cycles, Issued: June 30, 2010 Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of Clothes Washers with Warm Rinse Cycles, Issued: June 30, 2010 Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of Clothes Washers with Warm Rinse Cycles, Issued: June 30, 2010. Draft of DOE interpretive rule, which sets out DOE's views on the clothes washer testing procedure described in 10 CFR § 430 Appendix J1, having to do with how to apply the testing procedures to washers with a warm rinse option. This draft interpretive rule represents DOE's interpretation of

75

ENERGY STAR Test Procedures and Verification | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ENERGY STAR » ENERGY STAR Test ENERGY STAR » ENERGY STAR Test Procedures and Verification ENERGY STAR Test Procedures and Verification The Department of Energy (DOE) is the lead agency in the development and revision of all test procedures for products in the ENERGY STAR® program, including those products that are also subject to DOE's Energy Conservation Standards program. As specifications are updated and new products or metrics are added to the ENERGY STAR program, DOE is responsible for developing and revising methods, responding to stakeholder comments, and answering any testing-related questions that arise as a result of the procedures being utilized. To simplify the process for interested parties, more information on the test procedure development for ENERGY STAR products can be found on each of

76

Rocky Flats ash test procedure (sludge stabilization)  

SciTech Connect

Rocky Flats Ash items have been identified as the next set of materials to be stabilized. This test is being run to determine charge sizes and soak times to completely stabilize the Rocky Flats Ash items. The information gathered will be used to generate the heating rampup cycle for stabilization. This test will also gain information on the effects of the glovebox atmosphere (moisture) on the stabilized material. This document provides instructions for testing Rocky Flats Ash in the HC-21C muffle furnace process.

Winstead, M.L.

1995-09-14T23:59:59.000Z

77

Test procedure forms for sludge retrieval and packaging  

SciTech Connect

This document provides test procedure forms for sludge retrieval and packaging tests in the 305 Cold Test Facility. The completed and approved forms provide all descriptions, criteria and analysis to safely perform sludge equipment tests in the 305 Cold Test Facility.

Feigenbutz, L.V.

1994-09-27T23:59:59.000Z

78

US advanced battery consortium in-vehicle battery testing procedure  

DOE Green Energy (OSTI)

This article describes test procedures to be used as part of a program to monitor the performance of batteries used in electric vehicle applications. The data will be collected as part of an electric vehicle testing program, which will include battery packs from a number of different suppliers. Most data will be collected by on-board systems or from driver logs. The paper describes the test procedure to be implemented for batteries being used in this testing.

NONE

1997-03-01T23:59:59.000Z

79

Acceptance test procedure: RMW Land Disposal Facility Project W-025  

SciTech Connect

This ATP establishes field testing procedures to demonstrate that the electrical/instrumentation system functions as intended by design for the Radioactive Mixed Waste Land Disposal Facility. Procedures are outlined for the field testing of the following: electrical heat trace system; transducers and meter/controllers; pumps; leachate storage tank; and building power and lighting.

Roscha, V. [Westinghouse Hanford Co., Richland, WA (United States)

1994-12-12T23:59:59.000Z

80

The Effect of Inlet Flow Profile Distortion on Fan Performance  

Science Conference Proceedings (OSTI)

Performance tests on fans for utility and industrial applications are based on codes that expect a relatively uniform velocity profile at the fan inlet. Unfortunately, when fans scaled up from the ideal model fans are installed in actual utility and industrial applications, non-uniform or distorted flow patterns often occur at the inlet of the fan. This project sought to determine and, if possible, quantify the effect on fan performance of distorted inlet flow profiles. A second goal was to determine whe...

2010-02-22T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

NERVA Program. Operating procedure: cart cooling system, Test Cell A  

SciTech Connect

The instructions described in this procedure are typical of the operation of Test Cell A relative to the KIWI-B4A. Operation of Test Cell A relative to the NRX reactor will require modifications dictated by specific test requirements. Under NRX conditions, it will be the responsibility of the test cell manager to evaluate the capabilities of Test Cell A in terms of given test requirements and then set forth detailed checklists which will be compatible with the test requirements.

1963-09-01T23:59:59.000Z

82

Approved Test Procedures Version 1.1 Release Notes  

E-Print Network (OSTI)

Approved Test Procedures Version 1.1 Release Notes 1 Change Reason for Change 302.a drugdrug, drug allergy In the Informative Test Description section Added clarification to the example. 302.c Problem List In the Informative Test Description section Added the sentence "The test also

83

NBSBR 84-2867 Test Procedures for Rating  

E-Print Network (OSTI)

NBSBR 84-2867 Test Procedures for Rating Residential Heating and Cooling Absorption Equipment U HEATING AND COOLING ABSORPTION EQUIPMENT Brian Weber Reinhard Radermacher David Didion U.S. DEPARTMENT-fired absorption devices operating in either the heating or cooling modes. These procedures are designed to include

Oak Ridge National Laboratory

84

USABC electric vehicle Battery Test Procedures Manual. Revision 2  

DOE Green Energy (OSTI)

This manual summarizes the procedural information needed to perform the battery testing being sponsored by the United States Advanced Battery Consortium (USABC). This information provides the structure and standards to be used by all testing organizations, including the USABC developers, national laboratories, or other relevant test facilities.

NONE

1996-01-01T23:59:59.000Z

85

DOE Seeks Comment on Application of Clothes Washer Test Procedure |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Application of Clothes Washer Test Procedure Application of Clothes Washer Test Procedure DOE Seeks Comment on Application of Clothes Washer Test Procedure June 30, 2010 - 3:02pm Addthis Today, the U.S. Department of Energy (DOE) issued a draft interpretative rule clarifying its views on the application of the current residential clothes washer test procedure to machines that offer a warm rinse option that is not included in the recommended cycle for washing cotton or linen clothes. The Department is soliciting feedback from the public on the draft interpretive rule, which is available here, until July 30, 2010. Addthis Related Articles Save Energy and More with ENERGY STAR. ENERGY STAR clothes washers use 50% less energy to wash clothes than standard washing machines. Tips: Laundry DOE Solicits Views on the Implementation of Large-Capacity Clothes Washer

86

DOE Seeks Comment on Application of Clothes Washer Test Procedure |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Seeks Comment on Application of Clothes Washer Test Procedure Seeks Comment on Application of Clothes Washer Test Procedure DOE Seeks Comment on Application of Clothes Washer Test Procedure June 30, 2010 - 3:02pm Addthis Today, the U.S. Department of Energy (DOE) issued a draft interpretative rule clarifying its views on the application of the current residential clothes washer test procedure to machines that offer a warm rinse option that is not included in the recommended cycle for washing cotton or linen clothes. The Department is soliciting feedback from the public on the draft interpretive rule, which is available here, until July 30, 2010. Addthis Related Articles DOE Seeks Comment on Definition of Showerhead Save Energy and More with ENERGY STAR. ENERGY STAR clothes washers use 50% less energy to wash clothes than standard washing machines.

87

Flammable gas interlock spoolpiece flow response test plan and procedure  

DOE Green Energy (OSTI)

The purpose of this test plan and procedure is to test the Whittaker electrochemical cell and the Sierra Monitor Corp. flammable gas monitors in a simulated field flow configuration. The sensors are used on the Rotary Mode Core Sampling (RMCS) Flammable Gas Interlock (FGI), to detect flammable gases, including hydrogen and teminate the core sampling activity at a predetermined concentration level.

Schneider, T.C., Fluor Daniel Hanford

1997-02-13T23:59:59.000Z

88

Development of In-Situ Fan Curve Measurement with One Airflow Measurement  

E-Print Network (OSTI)

Fan airflow is the key parameter for air volume tracking control in variable air volume systems. One of the airflow measurement methods is to determine airflow using the fan speed, fan head, and fan curve. Both fan speed and fan head can be measured accurately. Therefore, the accuracy of the fan airflow depends on the accuracy of the fan curve. An experimental method has been developed to determine the in-situ fan curve with only one airflow measurement. This paper presents the theoretical background, experimental procedures, and verification results.

Liu, G.; Joo, I. S.; Song, L.; Liu, M.

2003-01-01T23:59:59.000Z

89

International Comparison of Energy Efficiency Criteria and Test Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

International Comparison of Energy Efficiency Criteria and Test Procedures International Comparison of Energy Efficiency Criteria and Test Procedures in Standards and Labeling Programs for Computer Monitors and Commercial Gas Stoves Title International Comparison of Energy Efficiency Criteria and Test Procedures in Standards and Labeling Programs for Computer Monitors and Commercial Gas Stoves Publication Type Report LBNL Report Number LBNL-6506E Year of Publication 2013 Authors Khanna, Nina, Nan Zhou, David Fridley, and John Romankiewicz Date Published 12/2013 Publisher Lawrence Berkeley National Laboratory Keywords Standards and labeling Abstract This report presents a technical review and comparative analysis of existing and/or proposed international mandatory energy performance standards, and voluntary and mandatory energy efficiency labels and test procedures for two products - computer monitors and commercial gas stoves - being considered for revised and new minimum energy performance standards (MEPS) in China. An overview of the scope of international programs, energy efficiency and other energy-related requirements, description and detailed summary table of criteria and procedures in major test standards are presented. In addition, an estimation of potential energy savings if China were to adopt revised MEPS comparable to international levels is provided for computer monitors. A proposed methodology for estimating potential energy savings based on the European Union experience is provided for commercial gas stoves in the absence of available sales or energy consumption data.

90

Fan Mei | BNL  

NLE Websites -- All DOE Office Websites (Extended Search)

Fan Mei Postdoctoral Research Associate Fan is currently working as a postdoctoral research associate with Jian Wang, investigating aerosol microphysical properties in three recent...

91

Operability test procedure [Tank] 241-SY-101 equipment removal system  

DOE Green Energy (OSTI)

The 241-SY-101 equipment removal system (ERS) consists of components, equipment, instrumentation and procedures that will provide the means to disconnect, retrieve, contain, load and transport the Mitigation Pump Assembly (MPA) from waste Tank 241-SY-101 to the Central Waste Complex (CWC). The Operability Test Procedure (OTP) will test the interfaces between ERS components and will rehearse the procedure for MPA removal and transportation to the extent they can be mocked-up at the CTF (Cold Test Facility). At the conclusion of the OTP, the ERS components and equipment will be removed from the CTF, entered into the Component Based Recall System (CBRS), and stored until needed for actual MPA removal and transportation.

Mast, J.C.

1994-12-08T23:59:59.000Z

92

Performance of ECM controlled VAV fan powered terminal units  

E-Print Network (OSTI)

Empirical performance models of fan airflow, primary airflow and power consumption were developed for series and parallel variable air volume fan powered terminal units. An experimental setup and test procedure were created to test the terminal units at typical design pressures and airflows. Each terminal unit observed in this study used an 8 in (20.3 cm) primary air inlet. Two fan motor control methods were considered. The primary control of interest was the electronically commutated motor (ECM) controller. Data collected were compared with previous research regarding silicon rectified control (SCR) units. Generalized models were developed for both series and parallel terminal units. Coefficients for performance models were then compared with comparable SCR controlled units. Non-linear statistical modeling was performed using SPSS software (2008). In addition to airflow and power consumption modeling, power quality was also quantified. Relationships between real power (watts) and apparent power (VA) were presented as well as harmonic frequencies and total harmonic distortion. Power quality was recorded for each ECM controlled terminal unit tested. Additional tests were also made to SCR controlled terminal units used in previous research (Furr 2006). The airflow and power consumption performance models had an R2 equal to 0.990 or greater for every terminal unit tested. An air leakage model was employed to account for leakage in the parallel designed VAV terminal units when the internal fan was turned off. For the leakage model, both ECM and SCR controlled units achieved an R2 greater than or equal to 0.918.

Cramlet, Andrew Charles

2008-08-01T23:59:59.000Z

93

PUREX (SAMCONS) uninterruptible power supply (UPS) acceptance test procedure  

SciTech Connect

This Acceptance Test Procedure for the PUREX Surveillance and Monitoring and Control System (SAMCONS) Uninterruptible Power Supply (UPS) provides for testing and verifying the proper operation of the control panel alarms and trouble functions, the 6roper functioning of the AC inverter, ability of the battery supply to maintain the SAMCONS load for a minimum of two hours , and proper interaction with the SAMCONS Video graphic displays for alarm displays.

Blackaby, W.B.

1997-09-01T23:59:59.000Z

94

241-AZ-101 Mixer Pump Demonstration Test Gamma Cart Acceptance Test Procedure and Quality Test Plan (ATP and QTP)  

Science Conference Proceedings (OSTI)

Shop Test of the Gamma Cart System to be used in the AZ-101 Mixer Pump Demonstration Test. Tests hardware and software. This procedure involves testing the Instrumentation involved with the Gamma Cart System, local and remote, including: depth indicators, speed controls, interface to data acquisition software and the raising and lowering functions. This Procedure will be performed twice, once for each Gamma Cart System. This procedure does not test the accuracy of the data acquisition software.

WHITE, D.A.

2000-03-01T23:59:59.000Z

95

241-AZ-101 Mixer Pump Demonstration Test Gamma Cart Acceptance Test Procedure and Quality Test Plan (ATP and QTP)  

SciTech Connect

Shop test of the sludge mobilization cart system to be used in the AZ-101 Mixer Pump Demonstration Test Tests hardware and software. This procedure involves testing the Instrumentation involved with the Gamma Cart System, local and remote, including depth indicators, speed controls, interface to data acquisition software and the raising and lowering functions. This Procedure will be performed twice, once for each Gamma Cart System. This procedure does not test the accuracy of the data acquisition software.

WHITE, D.A.

2000-01-27T23:59:59.000Z

96

Acceptance test report for the AN valve pit leak detection and low point drain assembly mock up test procedure  

SciTech Connect

This document describes The Performance Mock-up Test Procedure for the Valve Pit Leak Detection and Low Point Drain Assembly Performance Mock-Up Test Procedure.

EWER, K.L.

1999-07-20T23:59:59.000Z

97

The effect of fan and heat sink design on heat removal from microprocessor chips.  

E-Print Network (OSTI)

??Air flow and heat removal characteristics for fan/heat sink designs used to cool Pentium class processors were analyzed. Five designs were tested for fan speed,… (more)

Baltrip, Kedra G

2012-01-01T23:59:59.000Z

98

The Lillehammer Submarine Fan Complex.  

E-Print Network (OSTI)

??Abstract The Lillehammer Submarine Fan Complex is a mixed mud/sand rich turbidite fan system. The fan complex was deposited in the Neoproterozoic Hedmark rift basin… (more)

Skaten, Maren Kristin Møllerup

2006-01-01T23:59:59.000Z

99

Ceiling Fan | Open Energy Information  

Open Energy Info (EERE)

Ceiling Fan Jump to: navigation, search TODO: Add description List of Ceiling Fan Incentives Retrieved from "http:en.openei.orgwindex.php?titleCeilingFan&oldid267151"...

100

Residential Clothes Washers Test Procedure Notice of Proposed Rulemaking  

NLE Websites -- All DOE Office Websites (Extended Search)

19:12 Sep 20, 2010 19:12 Sep 20, 2010 Jkt 220001 PO 00000 Frm 00001 Fmt 4717 Sfmt 4717 E:\FR\FM\21SEP2.SGM 21SEP2 srobinson on DSKHWCL6B1PROD with PROPOSALS2 Tuesday, September 21, 2010 Part II Department of Energy 10 CFR Part 430 Energy Conservation Program for Consumer Products: Test Procedure for Residential Clothes Washers; Proposed Rule VerDate Mar2010 19:12 Sep 20, 2010 Jkt 220001 PO 00000 Frm 00002 Fmt 4701 Sfmt 4702 E:\FR\FM\21SEP2.SGM 21SEP2 srobinson on DSKHWCL6B1PROD with PROPOSALS2 57556 Federal Register / Vol. 75, No. 182 / Tuesday, September 21, 2010 / Proposed Rules DEPARTMENT OF ENERGY 10 CFR Part 430 [Docket No. EERE-2010-BT-TP-0021] RIN 1904-AC08 Energy Conservation Program for Consumer Products: Test Procedure for Residential Clothes Washers AGENCY: Office of Energy Efficiency and

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid N  

Science Conference Proceedings (OSTI)

This is a Test Report for Acceptance Test Procedure (ATP) RPP-5489. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''N''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document.

KOCH, M.R.

2000-02-03T23:59:59.000Z

102

Lightning arrestor connector lead magnesium niobate qualification pellet test procedures.  

SciTech Connect

Enhanced knowledge preservation for DOE DP technical component activities has recently received much attention. As part of this recent knowledge preservation effort, improved documentation of the sample preparation and electrical testing procedures for lead magnesium niobate--lead titanate (PMN/PT) qualification pellets was completed. The qualification pellets are fabricated from the same parent powders used to produce PMN/PT lightning arrestor connector (LAC) granules at HWF&T. In our report, the procedures for fired pellet surface preparation, electrode deposition, electrical testing and data recording are described. The dielectric measurements described in our report are an information only test. Technical reasons for selecting the electrode material, electrode size and geometry are presented. The electrical testing is based on measuring the dielectric constant and dissipation factor of the pellet during cooling from 280 C to 220 C. The most important data are the temperature for which the peak dielectric constant occurs (Curie Point temperature) and the peak dielectric constant magnitude. We determined that the peak dielectric constant for our procedure would be that measured at 1 kHz at the Curie Point. Both the peak dielectric constant and the Curie point parameters provide semi-quantitative information concerning the chemical and microstructural homogeneity of the parent material used for the production of PMN/PT granules for LACs. Finally, we have proposed flag limits for the dielectric data for the pellets. Specifically, if the temperature of the peak dielectric constant falls outside the range of 250 C {+-} 30 C we propose that a flag limit be imposed that will initiate communication between production agency and design agency personnel. If the peak dielectric constant measured falls outside the range 25,000 {+-} 10,000 we also propose that a flag limit be imposed.

Tuohig, W. (Honeywell FM& T, Kansas City, MO); Mahoney, Patrick A.; Tuttle, Bruce Andrew; Wheeler, Jill Susanne

2009-02-01T23:59:59.000Z

103

Nien-fan Zhang  

Science Conference Proceedings (OSTI)

Nien-fan Zhang. Technical Areas of Research and Consulting: Statistical process control Time series analysis and forecasting. Awards: ...

2012-07-16T23:59:59.000Z

104

Fan blade development. Final report Sep 81-Sep 82  

SciTech Connect

The objective of this program was to develop an improved fan blade that could be utilized in place of the current steel fan blade on the Pedal Ventilator Kit (PVK). The goals of the program were to reduce both the unit cost and weight of the fan while maintaining its effectiveness and reliability. A value analysis study was conducted on the fan blade to determine material/design revisions that offered potential manufacturing economies. Based on the conclusions of the study, two designs were chosen for fabrication. The two fan designs were constructed and tested. As a result of the performance testing, one fan blade emerged as the optimum design. Fifteen fan blades of the optimum design were constructed for FEMA inspection and distribution. Preliminary specifications were generated for the fan blade assembly. in addition, production cost estimates based on a procurement of 100,000 units were formulated for FEMA budgetary purposes.

Buday, J.M.

1982-09-01T23:59:59.000Z

105

Test Procedure for 170.302.h Incorporate Laboratory Test Results APPROVED Version 1.1 September 24, 2010  

E-Print Network (OSTI)

Test Procedure for §170.302.h Incorporate Laboratory Test Results APPROVED Version 1.1 September 24, 2010 1 Test Procedure for §170.302 (h) Incorporate Laboratory Test Results This document describes the test procedure for evaluating conformance of complete EHRs or EHR modules1

106

Definitions common to all certification and test procedures are in: D-200 Definitions for Certification Procedures and Test Procedures for Vapor Recovery Systems  

E-Print Network (OSTI)

For the purpose of this procedure, the term "ARB " refers to the State of California Air Resources Board, and the term "ARB Executive Officer " refers to the Executive Officer of the ARB or his or her authorized representative or designate. 1.1 General Applicability This procedure applies to the determination of the one minute static pressure performance of a vapor recovery system of a cargo tank by fluid mechanical principles. This procedure applies to any vapor emissions associated with the dispensing of any fluid, although it is written to reflect application to the hydrocarbon vapors associated with the dispensing of gasoline. 1.2 Determinations of Compliance and Violation Determinations of certain modes of compliance with and violation of certification specifications is outlined in § 9. 1.3 Modifications Modification of this procedure may be necessary for vapors and fluids other than the hydrocarbon vapors associated with the dispensing of gasoline. Any modification of this method shall be subject to approval by the ARB Executive Officer. 2 PRINCIPLE AND SUMMARY OF TEST PROCEDURE Upon completion of loading operations at the bulk gasoline distribution facility, the gasoline cargo tank is pressurized, with nitrogen, to 18 inches water column. By using the total cargo California Air Resources Board March 17, 1999 TP-204.2, Page 1tank shell capacity, post-loading headspace volume, and the Ideal Gas Law, a one-minute maximum allowable pressure decay is calculated. The pressure decay is monitored for one minute and compliance is determined by comparison with the maximum allowable calculated value. The leak rate through the cargo tank internal vapor vent valve is similarly obtained. 3

unknown authors

1996-01-01T23:59:59.000Z

107

Federal Test Procedure Emissions Test Results from Ethanol Variable-Fuel Vehicle Chevrolet Luminas  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Federal Test Procedure Emissions Test Results from Federal Test Procedure Emissions Test Results from Ethanol Variable-Fuel Vehicle Chevrolet Luminas Kenneth J. Kelly, Brent K. Bailey, and Timothy C. Coburn National Renewable Energy Laboratory Wendy Clark Automotive Testing Laboratories, Inc. Peter Lissiuk Environmental Research and Development Corp. Presented at Society for Automotive Engineers International Spring Fuels and Lubricants Meeting Dearborn, MI May 6-8, 1996 The work described here was wholly funded by the U.S. Department of Energy, a U.S. government agency. As such, this information is in the public domain, may be copied and otherwise accessed freely, and is not subject to copyright laws. These papers were previously published in hard copy form by the Society of Automotive Engineers, Inc. (Telephone: 412.776.4970; E-mail: publications@sae.org)

108

Test plan/procedure for the SPM-1 shipping container system. Revision 0  

SciTech Connect

The 49 CFR 173.465 Type A packaging tests will verify that SPM-1 will provide adequate protection and pass as a Type A package. Test will determine that the handle of the Pig will not penetrate through the plywood spacer and rupture the shipping container. Test plan/procedure provides planning, pre-test, setup, testing, and post-testing guidelines and procedures for conducting the {open_quotes}Free Drop Test{close_quotes} procedure for the SPM-1 package.

Flanagan, B.D.

1995-07-01T23:59:59.000Z

109

Record of Communication Concerning Ceiling Fan and Ceiling Fan...  

NLE Websites -- All DOE Office Websites (Extended Search)

Record of Communication Concerning Ceiling Fan and Ceiling Fan Light Kit Framework Document-Docket No. EERE-2012-BT-STD-0045 Record of Communication Concerning Ceiling Fan and...

110

Modeling of ECM Controlled Series Fan-powered VAV Terminal Units  

E-Print Network (OSTI)

Semi-empirical models for series fan-powered variable air volume terminal units (FPTUs) were developed based on models of the primary, plenum, fan airflow and the fan power consumption. The experimental setups and test procedures were developed respectively for primary, plenum and fan airflow to test each component of the FPTUs at typical design pressures and airflows. Two sizes of the terminal units from three manufacturers were used in this study. All of the FPTUs were equipped with electronically commutated motors (ECM). Data provided by the models were compared against the data from previous experiments to prove the models’ validity. Regression modeling was performed by using SigmaStat. The model of primary airflow had an R2 above 0.948 for all the terminal units evaluated while the plenum airflow model had an R2 above 0.99. For all the terminal units, the R2 of the fan airflow model was ranged from 0.973 to 0.998. Except for one fan, the fan power consumption model was able to characterize the power performance and had an R2 above 0.986. By combining the airflow and power models, the model for series FPTU was developed. Verification was made to prove the FPTU model’s validity by comparing the measured and predicted data of airflow and power consumption. Correction factors were used in the primary airflow model to compensate for the difference caused by large measurement errors and the system effects. The predicted values were consistent with measurements and no offset was needed in the primary airflow model. Generally, the newly established model was able to describe the airflow performance as well as power consumption of series FPTUs without adding complexity.

Yin, Peng

2010-08-01T23:59:59.000Z

111

Supply Fan Control for Constant Air Volume Air Handling Units  

E-Print Network (OSTI)

Since terminal boxes do not have a modulation damper in constant volume (CV) air handling unit (AHU) systems, zone reheat coils have to be modulated to maintain the space temperature with constant supply airflow. This conventional control sequence causes a significant amount of reheat and constant fan power under partial load conditions. Variable Frequency Drives (VFDs) can be installed on these constant air volume systems. The fan speed can be modulated based on the maximum zone load. This paper present the procedure to control the supply fan speed and analyzes the thermal performance and major fan energy and thermal energy savings without expensive VAV retrofit through the actual system operation.

Cho, Y.; Wang, G.; Liu, M.

2007-01-01T23:59:59.000Z

112

Sandia National Laboratories Electrochemical Storage System Abuse Test Procedure Manual  

DOE Green Energy (OSTI)

The series of tests described in this report are intended to simulate actual use and abuse conditions and internally initiated failures that may be experienced in electrochemical storage systems (ECSS). These tests were derived from Failure Mode and Effect Analysis, user input, and historical abuse testing. The tests are to provide a common framework for various ECSS technologies. The primary purpose of testing is to gather response information to external/internal inputs. Some tests and/or measurements may not be required for some ECSS technologies and designs if it is demonstrated that a test is not applicable, and the measurements yield no useful information.

Unkelhaeuser, Terry; Smallwood David

1999-07-01T23:59:59.000Z

113

Adams disassembly procedure for Bldg. 10, Nevada Test Site  

SciTech Connect

The disassembly of the `Adams` primary was scheduled for April 28, 29, and 30, 1959. The method of disassembly is provided as a procedure to be accomplished in order and the time and initials of the person accomplishing each step recorded.

Beckman, K. F.

1959-04-24T23:59:59.000Z

114

How to Make Appliance Standards Work: Improving Energy and Water Efficiency Test Procedures  

E-Print Network (OSTI)

test procedures for appliances. ” Energy and BuildingsEnergy Efficiency In Domestic Appliances And Lighting 4thLBNL # How to Make Appliance Standards Work: Improving

Lutz, Jim

2012-01-01T23:59:59.000Z

115

Modeling of Electronically Commutated Motor Controlled Fan-powered Terminal Units  

E-Print Network (OSTI)

Empirical models of airflow and power consumption were developed for series and parallel variable air volume fan powered terminal units (FPTUs). An experimental setup and test procedure were developed to test the terminal units over typical operating ranges. The terminal units in this study used either an 8 in. (20.32 cm) or a 12 in. (30.48 cm) primary air inlet. All terminal units utilized electronically commutated motor (ECM) controllers. Data collected were compared against previous data collected for silicon controlled rectifier (SCR) units. Generalized models were developed for both series and parallel units, and compared against models developed for SCR units. In addition to the performance modeling, power factor and power quality data were also collected for each terminal unit. The power quality analysis included recording and analyzing harmonic distortion for current, voltage, and power up to the 25th harmonic. The total harmonic distortion (THD) was also recorded and presented. For the series terminal units, models were developed for fan airflow, fan power, and primary airflow. The models for fan airflow all had R2 values above 0.987. The models for fan power all had R2 values above 0.968. The models for primary airflow all had R2 values above 0.895. For the parallel terminal units, models were developed for leakage, fan airflow, fan power, and primary airflow. All of the leakage models had R2 values above 0.826. All of the fan airflow models had R2 values above 0.955. All of the fan power models had R2 values above 0.922. All of the primary airflow models had R2 values above 0.872. The real power THD was below 1.5 percent for both series and parallel FPTUs. The current THD ranged from 84 percent to 172 percent for series FPTUs and from 83 percent to 183 percent for parallel FPTUs. The voltage THD was below 1.4 percent for both series and parallel FPTUs. The performance models developed will help improve the accuracy of building energy simulation programs for heating, ventilation, and air conditioning (HVAC) systems utilizing ECM controlled FPTUs. Increasing the accuracy of these simulations will allow HVAC system designers to better optimize their designs for specific building types in a wide variety of climates.

Edmondson, Jacob Lee

2009-12-01T23:59:59.000Z

116

An evaluation of predictive environmental test procedures for sewage sludge.  

E-Print Network (OSTI)

??This research project aimed at evaluating four internationally accepted leachate extraction tests to determine their applicability on sewage sludge samples. Furthermore, the present analytical method… (more)

Kasselman, Graeme

2005-01-01T23:59:59.000Z

117

Evaluation of the cooling fan efficiency index.  

E-Print Network (OSTI)

Evaluation of the Cooling Fan Efficiency indexfor a desk fan anda computer fan Stefano Schiavon 1,2,* , M. Sc. PhD

Schiavon, Stefano; Melikov, Arsen

2009-01-01T23:59:59.000Z

118

Smart Fan Modules And System  

DOE Patents (OSTI)

A fan module including: two or more individual fans, each fan having an air movement means and a motor engaged with the air movement means for accelerating air entering each of the two or more individual fans; a temperature sensor for sensing a temperature associated with the two or more fans and for outputting a first signal corresponding to the temperature; rotational speed sensor for outputting a second signal corresponding to a rotational speed of each of the two or more fans; and a processor for receiving the first and second signals and controlling the two or more individual fans based on the first and second signals. A fan module including: two or more individual fans, each fan having an air movement means and a motor engaged with the air movement means for accelerating air entering each of the two or more individual fans; a temperature sensor for sensing a temperature associated with the two or more fans and for outputting a first signal corresponding to the temperature; rotational speed sensor for outputting a second signal corresponding to a rotational speed of each of the two or more fans; and a processor for receiving the first and second signals and controlling the two or more individual fans based on the first and second signals.

Cipolla, Thomas M. (Katonah, NY); Kaufman, Richard I. (Somers, NY); Mok, Lawrence S. (Brewster, NY)

2003-07-15T23:59:59.000Z

119

Thermal test procedure for a paraboloid concentrator solar cooker  

SciTech Connect

Suitable thermal tests have been identified for performance evaluation of a concentrating solar cooker. These tests provide parameters that characterize the performance of the solar cooker, and are more or less independent of the climatic variables. The overall heat loss factor is obtained from the cooling curve and the optical efficiency factor is determined from the heating curve - both under full load conditions. The performance characteristic curve for the solar cooker is obtained and discussed. The study indicates that the no load test, which is useful in the case of a box type solar cooker, is not appropriate in the case of concentrator type cookers.

Mullick, S.C.; Kandpal, T.C.; Kumar, S. (Indian Institute of Technology, New Delhi (India))

1991-01-01T23:59:59.000Z

120

Testing a Procedure for Automatic Classification of Hydrometeor Types  

Science Conference Proceedings (OSTI)

Examples of automatic interpretation of polarimetric measurements made with an algorithm that classifies precipitation, from an Oklahoma squall line and a Florida airmass storm are presented. Developed in this paper are sensitivity tests of this ...

Dus?an S. Zrni?; Alexander Ryzhkov; Jerry Straka; Yidi Liu; J. Vivekanandan

2001-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

A class of matrices to test inversion procedures  

Science Conference Proceedings (OSTI)

The test matrices given by M. L. Pei [Comm. ACM 5, 10 (Oct. 1962), 508] and R. D. Rodman [Comm. ACM 6, 9 (Sept. 1963, 515] are special cases of a general class of matrices with complex elements for which an explicit ...

Randall E. Cline

1964-12-01T23:59:59.000Z

122

Gas characterization system 241-AN-105 field acceptance test procedure  

DOE Green Energy (OSTI)

This document details the field Acceptance Testing of a gas characterization system being installed on waste tank 241-AN-105. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases.

Schneider, T.C.

1996-03-01T23:59:59.000Z

123

Gas characterization system 241-AW-101 field acceptance test procedure  

DOE Green Energy (OSTI)

This document details the field Acceptance Testing of a gas characterization system being installed on waste tank 241-AW-101. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases.

Schneider, T.C.

1996-03-01T23:59:59.000Z

124

Fans for Cooling | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fans for Cooling Fans for Cooling Fans for Cooling May 30, 2012 - 7:46pm Addthis Ceiling fans circulate air in a room to help keep occupants cool. | Photo courtesy of ©iStockphoto/jimkruger Ceiling fans circulate air in a room to help keep occupants cool. | Photo courtesy of ©iStockphoto/jimkruger What does this mean for me? You may be able to keep your home cool with energy-efficient and well-placed fans. Fans are less expensive to operate than air conditioners. Circulating fans include ceiling fans, table fans, floor fans, and fans mounted to poles or walls. These fans create a wind chill effect that will make you more comfortable in your home, even if it's also cooled by natural ventilation or air conditioning. Ceiling Fans Ceiling fans are considered the most effective of these types of fans,

125

Qualification test procedures and results for Honeywell solar collector subsystem, single-family residence  

DOE Green Energy (OSTI)

The test procedures and results are described in qualifying the Honeywell solar collector subsystem. Testing began in mid-August 1976, and was concluded in late February 1977. Testing was done in the following areas: pressure, service loads, hail, solar degradation, pollutants, thermal degradation, and outgassing. Results from these tests are summarized.

Not Available

1977-02-01T23:59:59.000Z

126

Introduction of a Cooling Fan Efficiency Index  

E-Print Network (OSTI)

with four cooling fans of different designs available on thedesign, installation, and use, the performance of cooling fans

Schiavon, Stefano; Melikov, Arsen

2009-01-01T23:59:59.000Z

127

Building Energy Simulation Test for Existing Homes (BESTEST-EX): Instructions for Implementing the Test Procedure, Calibration Test Reference Results, and Example Acceptance-Range Criteria  

Science Conference Proceedings (OSTI)

This publication summarizes building energy simulation test for existing homes (BESTEST-EX): instructions for implementing the test procedure, calibration tests reference results, and example acceptance-range criteria.

Judkoff, R.; Polly, B.; Bianchi, M.; Neymark, J.; Kennedy, M.

2011-08-01T23:59:59.000Z

128

Developing a standardized test procedure for hybrid vehicles: The challenge of the SAE HEV task force  

DOE Green Energy (OSTI)

In 1992, the Society of Automotive Engineers (SAE) established a task force to develop a procedure for measuring electric energy consumption, all-electric range, fuel economy, and exhaust emissions for hybrid vehicles; the procedure will be submitted to regulatory agencies as representing the automotive industry`s recommendations. The draft procedure is currently being tested on hybrid vehicles. The University of Maryland`s parallel hybrid was tested in September 1994, and the University of California-Davis` parallel hybrid and the University of Illinois` series hybrid will be tested in November 1994 and January 1995, respectively. The procedure is being modified to incorporate any lessons learned, and the task force hopes to recommend the final procedure to the SAE by mid 1995.

Penney, T; Christensen, D [National Renewable Energy Lab., Golden, CO (United States); Poulos, S [General Motors Corp., Warren, MI (United States)

1994-11-01T23:59:59.000Z

129

Novel Battery Testing Procedures and Analytical Methodologies for Hybrid Electric Vehicles  

SciTech Connect

The Idaho National Engineering and Environmental Laboratory has developed novel testing procedures and analytical methodologies to assess the performance of batteries for use in hybrid electric vehicles. Tests include both characterization and cycle life and/or calendar life. Tests have been designed for both Power Assist and Dual Mode applications. Analytical procedures include a battery scaling methodology, the calculation of pulse resistance, pulse power, available energy, and differential capacitance, and the modeling of calendar and cycle life data. At periodic intervals during life testing, a series of Reference Performance Tests are executed to determine changes in the baseline performance of the batteries.

Motloch, Chester George; Batt, J. R.; Christophersen, Jon Petter; Wright, Randy Ben; Hunt, Gary Lynn

2001-06-01T23:59:59.000Z

130

Supervisory Control and Data Acquisition System (SCADA) Substation C3-3 Acceptance Test Procedure  

Science Conference Proceedings (OSTI)

The purpose of this acceptance test procedure (ATP) is to demonstrate that the newly installed Supervisory Control and Data Acquisition (SCADA) computer system functions as intended by the design.

ZAKRAJSEK, M.F.

2000-10-17T23:59:59.000Z

131

Supervisory Control and Data Acquisition System (SCADA) Substation C3S4 Acceptance Test Procedure  

Science Conference Proceedings (OSTI)

The purpose of this acceptance test procedure (ATP) is to demonstrate that the newly installed Supervisory Control and Data Acquisition (SCADA) computer system functions as intended by the design.

ZAKRAJSEK, M.F.

2000-10-17T23:59:59.000Z

132

Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

IESNA LM-80-08 - An Overview IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® to someone by E-mail Share Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Facebook Tweet about Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Twitter Bookmark Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Google Bookmark Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Delicious Rank Solid-State Lighting: IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® on Digg Find More places to share Solid-State Lighting: IESNA LM-80-08 -

133

Interim test methods and procedures for determining the performance of small photovoltaic systems  

DOE Green Energy (OSTI)

This document provides test methods and procedures for determining the performance of small stand-alone and utility-grid connected PV systems. The procedures in this document provide a common approach for evaluating whether a given PV system is suitable to perform the function it was designed and manufactured to accomplish and meet the application load. This test document fills a testing void and provides the catalyst and focus for establishing the technical foundation and bridging the institutional barriers needed to reduce uncertainty that a system`s performance will be what its designers and builders claim. The need for this document was recently made more apparent with the initiation of a PV Global Approval Program (PVGAP) at the international level and is in response to concerns that PV systems being fielded must meet performance standards and that these standards include system-level performance type tests. The title of these test procedures is prefaced with the word interim because experience in using the procedures is needed before a consensus standard is developed and accepted by the PV community through its activities with the IEEE Standards Coordinating Committee 21 (SCC21) and International Electrotechnical Commission Technical Committee 82 (IEC TC82) national and international standards-making bodies. Both entities have initiated projects to develop test standards and will need the technical basis and validation of test procedures such as those presented in this document before a consensus is achieved by the PV community.

McNutt, P.; Kroposki, B.; Hansen, R.; DeBlasio, R.

1998-07-01T23:59:59.000Z

134

Fan System Effects: How Fan Ductwork Design Impacts Overall System Efficiency and What the Approach Should be for Optimization  

E-Print Network (OSTI)

"In order to establish the aerodynamic performance characteristics of a custom fan or even a line of fans, the accepted practice of the industry is to carry out testing on a scale model in a laboratory to develop its fan performance curve. Then by applying affinity laws in conjunction with very specific rules that address scaling issues, the performance characteristics of geometrically similar fans can be predicted. These affinity laws (frequently referred to as fan laws) also allow the performance of fans operating at different speeds or handling gases at different density values to be accurately predicted. However, it is often found that even fans with well defined and pedigreed performance curves are unable to meet their performance expectations once they are installed on the systems for which they have been sold. This is primarily due to the adverse aerodynamic impact of the inlet or outlet connections on the performance capacity of the fan and thus on the overall system efficiency. The general term for design conditions at inlets or outlets of fans that cause deficient aerodynamic performance is ‘system effects’. The characteristics of fan system effects are that they reduce fan capacity and are both velocity and geometry dependent. On the inlet side of a fan, this generally characterizes itself by a flow pattern that is highly non?uniform. On the discharge side, the high and low velocity flow streams leaving the fan may simply be prevented from redeveloping a uniform flow profile and normal static pressure conversion before encountering a disturbance. The term can also apply to system elements such as silencers, elbows and transitions. For these components, the actual pressure drop across them may be significantly higher than their calculated or rated values if the velocity profile of the entering flow is skewed or non?uniform. For either case (fan connection or system component), the result is that additional power will be required to address the flow rate required by the system. In many instances, system designers are simply unfamiliar with the importance of understanding system effects as it pertains to new fan selections and the attendant power requirements. At a minimum, a reasonable approach for new fan projects should be to establish the theoretical system effect of connection designs by using a recognized document such as Air Movement and Control Association Publication 201. The objective should be to first minimize their impact through appropriate connection design modifications in conjunction with potential fan inlet and outlet re?orientation. Once the system effects are minimized, the residual value should be applied to the fan performance specification in order to ensure that the fan is selected for the required aerodynamic capacity. For system components, an approach that has proved to be of significant value is to predict the flow pattern using computation fluid dynamics (CFD) modelling tools and in this process, the design can be tweaked until the designer finds the overall pressure drops of a system are minimized to the greatest practical extent. Similarly, CFD can be used to predict the flow profile at a fan inlet to ensure that it is as uniform as practically possible. This paper reviews the concept of system effects from the perspective of fan power requirements and provides a methodology for approaching system design from the perspective of optimizing fan energy use while achieving the required system capacity."

Martin, V.

2009-05-01T23:59:59.000Z

135

Using virtual reality and mood-induction procedures to test products with consumers of ceramic tiles  

Science Conference Proceedings (OSTI)

This work describes a Virtual Reality Environment (VRE), through which users are able to view and test ceramic tile products. Users' virtual interfacing with the products generated emotional experiences that allowed them to feel ''engaged'' with the ... Keywords: Consumers, Mood-induction procedures, Product testing, Relaxation, Sense of presence, Virtual reality

Berenice Serrano; Cristina Botella; Rosa M. BañOs; Mariano AlcañIz

2013-05-01T23:59:59.000Z

136

Round-robin testing of Soleq EV cort according to the SAE J1634 test procedure dated May 1993  

DOE Green Energy (OSTI)

The Society of Automotive Engineers Recommended Practice, SAE J1634, {open_quotes}Electric Vehicle Energy Consumption and Range Test Procedure{close_quotes}, May 1993, describes a standard method of determining the range and energy consumption for electric vehicles. Consequent to the U.S. Department of Energy`s (DOE) rulemaking released on February 4, 1994, the EPA is currently considering factoring electric vehicles into the Corporate Average Fuel Economy (CAFE) calculations using the SAE J1634 procedure. The purpose of this project is to provide information regarding the suitability of this recommended practice for determining the energy economy value to be factored into the CAFE. Issues leading to possible inconsistent results (such as the repeatability of the procedure, thoroughness of the procedure`s methods, and variance between different laboratories using different dynamometers) need to be resolved prior to passing legislation which will mandate use of this test in determining the electric vehicle CAFE credit. To this end, separate tests were performed on a Soleq EVcort vehicle by the INEL, the EPA, Ford Motor Company, Southwest Research Institute, and the California Air Resources Board using their own facilities and personnel. Acceptable departures from the driving profile prescribed by SAEJ1634 are not well defined. This deficiency in the procedure is even more noticeable due to the EVcort`s marginal acceleration performance.

Cole, G.H.

1993-05-01T23:59:59.000Z

137

Development of an Outdoor Concentrating Photovoltaic Module Testbed, Module Handling and Testing Procedures, and Initial Energy Production Results  

DOE Green Energy (OSTI)

This report addresses the various aspects of setting up a CPV testbed and procedures for handling and testing CPV modules.

Muller, M.

2009-09-01T23:59:59.000Z

138

Energy Efficiency Program for Certain Commercial and Industrial Equipment: Test Procedures for  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6/2/11 6/2/11 Comments to the following DOE Proposed Rules: 10 CFR Part 431 [Docket No. EERE-2010-BT-TP-0036] RIN 1904-AC38 Energy Efficiency Program for Certain Commercial and Industrial Equipment: Test Procedures for Automatic Commercial Ice Makers Submitted by: Mary C. Howe, President, Howe Corporation, Chicago, IL 60642 mchowe@howecorp.com CORPORATION 1650 N Elston Ave * Chicago, IL. 60642 * (773) 235-0200 * Fax (773) 235-0269 * E-mail: howeinfo@howecorp.com 2 Item 1 - DOE also requests comment on the proposal that the use of amended test procedure be required upon the effective date of any test procedure final rule, 30 days after publication in the Federal Register. In the case of the addition of continuous production remote condenser ACIM's, the outside testing

139

Save Energy with Axial Fans  

E-Print Network (OSTI)

There are several ways to save energy in wet cooling towers and air cooled heat exchangers using axial fans. This paper will discuss ways to improve fan system efficiency in wet and dry towers both during the design phase and after installation by specifying energy efficient equipment. Variable pitch fan versus fixed pitch fan operation is discussed in terms of energy savings and means of control. The areas of interest to wet cooling tower users would be the influence on fan diameter and operating point on horsepower, how and when are velocity recovery stacks effective, the effect of varying fan speed to improve efficiency, and tip clearance effects. The areas of interest to dry tower (air cooled heat exchanger) users would be the effect of inlet losses, approach velocity losses, and losses due to air recirculation.

Monroe, R. C.

1981-01-01T23:59:59.000Z

140

Test procedures and instructions for single shell tank saltcake cesium removal with crystalline silicotitanate  

SciTech Connect

This document provides specific test procedures and instructions to implement the test plan for the preparation and conduct of a cesium removal test, using Hanford Single Shell Tank Saltcake from tanks 24 t -BY- I 10, 24 1 -U- 108, 24 1 -U- 109, 24 1 -A- I 0 1, and 24 t - S-102, in a bench-scale column. The cesium sorbent to be tested is crystalline siticotitanate. The test plan for which this provides instructions is WHC-SD-RE-TP-024, Hanford Single Shell Tank Saltcake Cesium Removal Test Plan.

Duncan, J.B.

1997-01-07T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Information Resources: IESNA LM-80-08 - An Overview of the Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® IESNA LM-80-08 - An Overview of the Test Procedure and How it is Used for ENERGY STAR® This October 30, 2008 webcast provided an overview of LM-80-08, Approved Method for Measuring Lumen Maintenance of LED Light Sources, and how DOE's ENERGY STAR program for Solid-State Lighting (SSL) Luminaires will use LM-80 to estimate lifetime for qualified SSL Luminaires. Richard Karney, U.S. Department of Energy, began the webcast with the announcement that LM-80-08 is now available through IESNA. The test procedure can be purchased online through the IES store at https://www.ies.org/store/. Kevin Dowling, Chairman, Testing Procedures SSL Committee, presented on the specifics of the LM-80 test procedure and the changes reflected in the final version. Jeff McCullough, Pacific Northwest National Laboratory, went through an overview of how the results of LM-80 are used for the DOE ENERGY STAR SSL program.

142

Performance Assessment of Photovoltaic Attic Ventilator Fans  

E-Print Network (OSTI)

Controlling summer attic heat gain is important to reducing air conditioning energy use in homes in hot-humid climates. Both heat transfer through ceilings and t attic duct systems can make up a large part of peak cooling demand, Attic ventilation has long been identified as a method to abate such heat gains. We present test results from using the photovoltaic (PV) attic ventilator fans in a test home to assess impact on attic and cooling energy performance.

Parker, D. S.; Sherwin, J. R.

2000-01-01T23:59:59.000Z

143

Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications  

NLE Websites -- All DOE Office Websites (Extended Search)

Interim Test Procedures for Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications S. Chakraborty, W. Kramer, B. Kroposki, G. Martin, P. McNutt, M. Kuss, T. Markel, and A. Hoke Technical Report NREL/TP-5500-51001 June 2011 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 1617 Cole Boulevard Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications S. Chakraborty, W. Kramer, B. Kroposki, G. Martin, P. McNutt, M. Kuss, T. Markel,

144

A Functional Test Procedure for the improved commissioning of a VAV system  

E-Print Network (OSTI)

In the context of the IEA40 research project, a specification of a “Functional Test Procedure” was progressively developed using the CA-MET building in Namur as real size test bench for the application and validation of the procedure. The target system is a typical VAV system devoted to the ventilation, cooling and air conditioning functions. The procedure consists in a series of operations to be applied to the system, considered as a set of connected components and taking into account the following constraints: 1) time availability 2) intrinsic limitations of the system 3) reference performances. The proposed procedure is divided in two sets of actions: 1) a number of preliminary actions allowing to take the best benefit of the subsequent phases: a) identification of available measurement points b) identification of actuators characteristics c) identification of control strategies d) aeraulic network calculations e) selection of measurement techniques and experimental design 2) the verification tasks themselves: The philosophy of the verification process is to bring the system into a number of states which allowed each specific check to be carried out. The organisation of the procedure tries to optimize the time spent for commissioning by logically sequencing the operations according to the following order: 1) test in manual (ie not controlled by the BEMS) operation 2) test in manual (ie not controlled by the BEMS) stop 3) test in normal operation 4) test at maximum flowrate 5) test at minimum flowrate 6) test in automatic stop The paper will provide the specific operations to be carried out at each step and will illustrate the whole process with the prototyping work performed on the CA-MET building in Namur.

Andre, P.; Lacote, P.; Aparecida Silva, C.; Hannay, J.; Lebrun, J.

2004-01-01T23:59:59.000Z

145

PNGV Battery Testing Procedures and Analytical Methodologies for Hybrid Electric Vehicles  

SciTech Connect

Novel testing procedures and analytical methodologies to assess the performance of hybrid electric vehicle batteries have been developed. Tests include both characterization and cycle life and/or calendar life, and have been designed for both Power Assist and Dual Mode applications. Analytical procedures include a battery scaling methodology, the calculation of pulse resistance, pulse power, available energy, and differential capacity, and the modeling of calendar and cycle life data. Representative performance data and examples of the application of the analytical methodologies including resistance growth, power fade, and cycle and calendar life modeling for hybrid electric vehicle batteries are presented.

Motloch, Chester George; Belt, Jeffrey R; Christophersen, Jon Petter; Wright, Randy Ben; Hunt, Gary Lynn; Haskind, H. J.; Tartamella, T.; Sutula, R.

2002-06-01T23:59:59.000Z

146

Introduction of a Cooling Fan Efficiency Index  

E-Print Network (OSTI)

°C °F Cooling Effect (?t eq ) °C °F Fan Power, W (P f ) Cooling-Fan Efficiency (CFE) °C/W °F/Wand B. Jones. 1983. Ceiling fans as extenders of the summer

Schiavon, Stefano; Melikov, Arsen

2009-01-01T23:59:59.000Z

147

The Internet World of Fan Fiction.  

E-Print Network (OSTI)

??Fan fiction, the most popular creative outlet for fans, allows the amateur writer an opportunity to be published and receive immediate feedback from peers. As… (more)

Herzing, Melissa Jean

2008-01-01T23:59:59.000Z

148

THE WORLD'S Biggest Fan Collection  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

WORLD'S Biggest Fan Collection WORLD'S Biggest Fan Collection If you only know the Big Ass Fan Company as the preeminent designer and manufacturer of high volume, low speed fans for factories and cows, it's time you get to know us better. While we continue to lead the way in industrial and agricultural air movement, we've also refined these designs to bring the same innovation and benefits of our famous fans to circulate an ocean of air in sound-sensitive commercial spaces and homes. And when our customers said they wanted something for smaller spaces, we listened - and we think you'll like the results. We've got you covered - ceiling to floor, wall to door! Features ï‚ž New patented airfoil system uses 10 Powerfoil airfoils, winglets and patent-pending AirFence(tm) technology to increase

149

DOE response to questions from AHAM on the supplemental proposed test procedure  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

response to questions from AHAM on the supplemental proposed test procedure for response to questions from AHAM on the supplemental proposed test procedure for residential clothes washers"? (1) What exactly does the language in Part B mean and what is the intent? * The intent of Part B is to use the methodology that AHAM had suggested specifically for extra-hot cycles, but to make it more broadly applicable to any temperature combination that is locked out of the Normal cycle. * The proposed Part (B) language is meant to be consistent with GE's original suggestion in response to the NOPR. (GE, No. 15 at pp. 1-2) * When testing cycles under Part (B), manufacturers would only need to test the temperature combination that is locked out of the Normal cycle.

150

Interim qualification tests and procedures for terrestrial photovoltaic thin-film flat-plate modules  

DOE Green Energy (OSTI)

This document provides recommended procedures and specifications for qualification tests that are structured to evaluate terrestrial thin-film flat-plate photovoltaic nonconcentrating modules intended for power generation applications. The qualification tests provided in this document are designed to evaluate flat-plate thin-film photovoltaic (PV) module design performance and susceptibility to known failure mechanisms. Emphasis is placed on testing and evaluating module performance characteristics and design features that will affect possible degradation of module performance and physical properties resulting from solar exposure, environmental weathering, mechanical loading, corrosion, and module shadowing. Because of limited thin-film module field operation experience and the evolutionary nature of new thin-film module material technologies and designs, these tests should not be considered definitive or complete, nor do they provide a basis to predict 30-year field life. Current understanding of failure and degradation mechanisms and the relationship between accelerated tests and field reliability is not sufficient to allow accurate estimation of life-expectancy, nor are the cycling tests given in this document considered to be equivalent to a full 30-year field exposure. However, the test and evaluation procedures given in this document provide a common approach for conducting qualification tests. Acceptable results from these tests should provide reasonable assurance that the modules that pass these tests will perform reliably in the field but for an unspecified period of time. 8 refs., 6 figs.

DeBlasio, R.; Mrig, L.; Waddington, D.

1990-01-01T23:59:59.000Z

151

Particle trajectories and acceleration during 3D fan reconnection  

E-Print Network (OSTI)

Context. The primary energy release in solar flares is almost certainly due to magnetic reconnection, making this a strong candidate as a mechanism for particle acceleration. While particle acceleration in 2D geometries has been widely studied, investigations in 3D are a recent development. Two main classes of reconnection regimes at a 3D magnetic null point have been identified: fan and spine reconnection Aims. Here we investigate particle trajectories and acceleration during reconnection at a 3D null point, using a test particle numerical code, and compare the efficiency of the fan and spine regimes in generating an energetic particle population. Methods. We calculated the time evolution of the energy spectra. We discuss the geometry of particle escape from the two configurations and characterise the trapped and escaped populations. Results. We find that fan reconnection is less efficent than spine reconnection in providing seed particles to the region of strong electric field where acceleration is possible. The establishment of a steady-state spectrum requires approximately double the time in fan reconnection. The steady-state energy spectrum at intermediate energies (protons 1 keV to 0.1 MeV) is comparable in the fan and spine regimes. While in spine reconnection particle escape takes place in two symmetric jets along the spine, in fan reconnection no jets are produced and particles escape in the fan plane, in a ribbon-like structure.

S. Dalla; P. K. Browning

2008-11-07T23:59:59.000Z

152

Evaluation of fine-particle size catalysts using standard test procedures  

SciTech Connect

The goal of this project is to evaluate and compare the activities/selectivities of fine-particle size catalysts being developed in the DOE/PETC Advanced Research (AR) Liquefaction Program by using standard coal liquefaction activity test procedures. Since bituminous and subbituminous coals have significantly different properties, it is feasible that catalysts may perform differently with these coal types. Because all previous testing has been done with the DECS-17 Blind Canyon bituminous coal, it is important to develop the capability of evaluating catalysts using a subbituminous coal. Initial efforts towards developing a subbituminous coal test are aimed at comparing the reactivities of the Wyodak subbituminous coal and the Blind Canyon bituminous coal. Therefore, the same factorial experimental design was used with the Wyodak coal as was used previously with the Blind Canyon coal. In addition, PNL`s 6-line ferrihydrite catalyst precursor was used in the development of the Wyodak coal test procedure because this catalyst is the best powder catalyst found to date in Sandia`s tests with Blind Canyon coal. Results show that Blind Canyon coal yields higher DHP amounts in the reaction products and higher tetrahydrofuran conversions at the higher severity conditions. Wyodak coal gives higher heptane conversions and higher gas yields for all conditions tested.

Stohl, F.V.; Diegert, K.V.; Goodnow, D.C.

1996-07-01T23:59:59.000Z

153

MEMORANDUM TO: File FROM: David R. Hill RE: Meeting Concerning Potential Test Procedures and Energy Conservation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

MEMORANDUM MEMORANDUM TO: File FROM: David R. Hill RE: Meeting Concerning Potential Test Procedures and Energy Conservation Standards for Set-Top Boxes and Network Equipment DATE: March 14, 2012 In compliance with the Department of Energy's guidance on ex parte communications (74 Fed. Reg. 52795 (Oct. 14, 2009)), this memorandum provides a summary of a March 7, 2012, meeting with DOE officials concerning potential test procedures and energy conservation standards for set-top boxes and network equipment. Meeting attendees: John Cymbalski (DOE - EE) Jeremy Dommu (DOE - EE) Ashley Armstrong (DOE - EE) Dan Cohen (DOE - GC) Celia Sher (DOE - GC) Cecilia Martaus (AT&T) Mike Pfau (AT&T) Jeff Dygert (AT&T) David Hill (Sidley Austin) The AT&T representatives discussed a number of concerns with DOE's potential promulgation

154

Sampling and Analysis Procedures for Gas, Condensate, Brine, and Solids: Pleasant Bayou Well Test, 1988-Present  

Science Conference Proceedings (OSTI)

This section covers analyses performed on gas. Chemical analyses can only be related to well performance if the quantity of the various fluids are known. The IGT on-line data computer system measures the flowrate, the pressures, and the temperatures every 10 seconds. These values are automatically recorded over operator selected intervals both on magnetic media and on paper. This allows review of samples versus operating conditions. This paper covers analyses performed on gas, including: An approximate sampling schedule during flow tests; On-site sample handling and storage of gas samples; Addresses of laboratories that perform off site analyses; Sample shipping instructions; Data archiving; and Quality Control/Quality Assurance. It is expected that the above procedures will change as the flow test progresses, but deviations from the written procedures should be approved by C. Hayden of IGT and noted on the results of the analysis.

Hayden, Chris

1988-01-01T23:59:59.000Z

155

Proposal for a Vehicle Level Test Procedure to Measure Air Conditioning Fuel Use  

SciTech Connect

The air-conditioning (A/C) compressor load significantly impacts the fuel economy of conventional vehicles and the fuel use/range of plug-in hybrid electric vehicles (PHEV). A National Renewable Energy Laboratory (NREL) vehicle performance analysis shows the operation of the air conditioner reduces the charge depletion range of a 40-mile range PHEV from 18% to 30% in a worst case hot environment. Designing for air conditioning electrical loads impacts PHEV and electric vehicle (EV) energy storage system size and cost. While automobile manufacturers have climate control procedures to assess A/C performance, and the U.S. EPA has the SCO3 drive cycle to measure indirect A/C emissions, there is no automotive industry consensus on a vehicle level A/C fuel use test procedure. With increasing attention on A/C fuel use due to increased regulatory activities and the development of PHEVs and EVs, a test procedure is needed to accurately assess the impact of climate control loads. A vehicle thermal soak period is recommended, with solar lamps that meet the SCO3 requirements or an alternative heating method such as portable electric heaters. After soaking, the vehicle is operated over repeated drive cycles or at a constant speed until steady-state cabin air temperature is attained. With this method, the cooldown and steady-state A/C fuel use are measured. This method can be run at either different ambient temperatures to provide data for the GREEN-MAC-LCCP model temperature bins or at a single representative ambient temperature. Vehicles with automatic climate systems are allowed to control as designed, while vehicles with manual climate systems are adjusted to approximate expected climate control settings. An A/C off test is also run for all drive profiles. This procedure measures approximate real-world A/C fuel use and assess the impact of thermal load reduction strategies.

Rugh, J. P.

2010-04-01T23:59:59.000Z

156

Building Energy Simulation Test for Existing Homes (BESTEST-EX): Instructions for Implementing the Test Procedure, Calibration Test Reference Results, and Example Acceptance-Range Criteria  

NLE Websites -- All DOE Office Websites (Extended Search)

Building Energy Simulation Test for Building Energy Simulation Test for Existing Homes (BESTEST-EX): Instructions for Implementing the Test Procedure, Calibration Test Reference Results, and Example Acceptance-Range Criteria Ron Judkoff, Ben Polly, and Marcus Bianchi National Renewable Energy Laboratory Joel Neymark J. Neymark & Associates Mike Kennedy Mike D. Kennedy, Inc. Link to Accompanying Zipped Data Files (3.9 MB) This document is intended for use with the following documents: Building Energy Simulation Test for Existing Homes (BESTEST-EX), NREL/TP-550-47427 Example Procedures for Developing Acceptance-Range Criteria for BESTEST-EX, NREL/TP-550-47502 Technical Report NREL/TP-5500-52414 August 2011 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy

157

Measurements and calculations on the simple up-down adaptive procedure for speech-in-noise tests  

Science Conference Proceedings (OSTI)

The simple up-down adaptive procedure is a common method for measuringspeech reception thresholds. It is used by the Dutch speech-in-noise telephone screening test [National Hearing test; Smits and Houtgast Ear Hear.26

Cas Smits; Tammo Houtgast

2006-01-01T23:59:59.000Z

158

title Potential Global Benefits of Improved Ceiling Fan Energy...  

NLE Websites -- All DOE Office Websites (Extended Search)

Fan Energy Efficiency year month keywords bottom up Ceiling fan Celing Fans efficiency energy efficiency Financial incentives Market Transformation residential Standards and...

159

COOLING FAN AND SYSTEM PERFORMANCE AND EFFICIENCY IMPROVEMENTS  

Science Conference Proceedings (OSTI)

Upcoming emissions regulations (Tiers 3, 4a and 4b) are imposing significantly higher heat loads on the cooling system than lesser regulated machines. This work was a suite of tasks aimed at reducing the parasitic losses of the cooling system, or improving the design process through six distinct tasks: 1. Develop an axial fan that will provide more airflow, with less input power and less noise. The initial plan was to use Genetic Algorithms to do an automated fan design, incorporating forward sweep for low noise. First and second generation concepts could not meet either performance or sound goals. An experienced turbomachinery designer, using a specialized CFD analysis program has taken over the design and has been able to demonstrate a 5% flow improvement (vs 10% goal) and 10% efficiency improvement (vs 10% goal) using blade twist only. 2. Fan shroud developments, using an 'aeroshroud' concept developed at Michigan State University. Performance testing at Michigan State University showed the design is capable of meeting the goal of a 10% increase in flow, but over a very narrow operating range of fan performance. The goal of 10% increase in fan efficiency was not met. Fan noise was reduced from 0 to 2dB, vs. a goal of 5dB at constant airflow. The narrow range of fan operating conditions affected by the aeroshroud makes this concept unattractive for further development at this time 3. Improved axial fan system modeling is needed to accommodate the numbers of cooling systems to be redesigned to meet lower emissions requirements. A CFD fan system modeling guide has been completed and transferred to design engineers. Current, uncontrolled modeling practices produce flow estimates in some cases within 5% of measured values, and in some cases within 25% of measured values. The techniques in the modeling guide reduced variability to the goal of + 5% for the case under study. 4. Demonstrate the performance and design versatility of a high performance fan. A 'swept blade mixed flow' fan was rapid prototyped from cast aluminum for a performance demonstration on a small construction machine. The fan was mounted directly in place of the conventional fan (relatively close to the engine). The goal was to provide equal airflow at constant fan speed, with 75% of the input power and 5 dB quieter than the conventional fan. The result was a significant loss in flow with the prototype due to its sensitivity to downstream blockage. This sensitivity to downstream blockage affects flow, efficiency, and noise all negatively, and further development was terminated. 5. Develop a high efficiency variable speed fan drive to replace existing slipping clutch style fan drives. The goal for this task was to provide a continuously variable speed fan drive with an efficiency of 95%+ at max speed, and losses no greater than at max speed as the fan speed would vary throughout its entire speed range. The process developed to quantify the fuel savings potential of a variable speed fan drive has produced a simple tool to predict the fuel savings of a variable speed drive, and has sparked significant interest in the use of variable speed fan drive for Tier 3 emissions compliant machines. The proposed dual ratio slipping clutch variable speed fan drive can provide a more efficient system than a conventional single ratio slipping clutch fan drive, but could not meet the established performance goals of this task, so this task was halted in a gate review prior to the start of detailed design. 6. Develop a cooling system air filtration device to allow the use of automotive style high performance heat exchangers currently in off road machines. The goal of this task was to provide a radiator air filtration system that could allow high fin density, louvered radiators to operate in a find dust application with the same resistance to fouling as a current production off-road radiator design. Initial sensitivity testing demonstrated that fan speed has a significant impact on the fouling of radiator cores due to fine dusts, so machines equipped with continuously variabl

Ronald Dupree

2005-07-31T23:59:59.000Z

160

Ceiling Fan and Ceiling Fan Light Kit use in the U.S. Results of a Survey on Amazon Mechanical Turk  

E-Print Network (OSTI)

Ceiling Fan and Ceiling Fan Light Kit use in the U.S. —Ceiling Fan and Ceiling Fan Light Kit use in the U.S. —fans and ceiling fan light kits in the United States (

Kantner, Colleen L.S.

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Sound maintenance practices protect fan investments  

Science Conference Proceedings (OSTI)

Since underground coal miners depend on axial fans, lack of maintenance could prove costly. A number of pre-emptive actions that can help keep fans running at optimal performance can also be taken. 2 photos.

Bauer, M.

2009-11-15T23:59:59.000Z

162

TF30 third-stage composite fan blade service program. Final technical report 1 Jul 1970--31 Dec 1977. [BORSIC/aluminum  

SciTech Connect

The successful application of advanced composites as the structural material for aircraft jet engine rotating parts will significantly reduce engine weight and improve engine performance characteristics. To solve the component design, manufacturing, and quality assurance problems associated with such an application, a program was conducted to design and develop BORSIC/Aluminum third-stage fan blades, which would operate satisfactorily in the TF30-P-7 or P-9 engine models. Program objectives successfully were to improve the existing design of a composite material fan blade, manufacture the blade, and demonstrate its quality by bench and engine environment testing. The scope of the program required to meet these objectives included establishing design and fabrication procedures, developing special tooling, evaluating current nondestructive inspection techniques and adapting these techniques to composite materials, establishing quality assurance criteria, and developing comprehensive bench and engine environment test programs to adequately demonstrate fan-blade quality. During the program, several sets of BORSIC/Aluminum blades weighing 40 percent less than comparable TF30 bill of material titanium blades were successfully produced and tested. On the basis of extensive test program, and with the establishment of quality control criteria and repair procedures, the blades were deemed acceptable for evaluation in a flight program. During the total program, 246 engine-configuration blades were manufactured and non-destructively inspected; with an overall acceptance rate of 92.3%.

Randall, D.G.

1978-05-15T23:59:59.000Z

163

Measured Natural Cooling Enhancement of a While House Fan  

E-Print Network (OSTI)

An experimental study was carried out in the summer of 1991 to investigate the natural cooling potential of use of a whole house fan in Central Florida's hot and humid climate. The residential building, in Cocoa Beach, FL, is typical of much of the existing housing stock in Florida: a concrete block structure with R-11 ceiling insulation. The building was ventilated with all windows open during the three month summer test period (June- August). Air temperatures and relative humidity inside the home interior along with exterior meteorological conditions (insolation, wind speed, air temperature, relative humidity) were scanned every five seconds with integrated averages recorded on a multi-channel data logger every 15- minutes. The house was naturally ventilated during the first half of summer. After a significant period of pre-retrofit summer data had been collected characterizing the building's thermal response, a 24" whole house fan was installed. The house was then force ventilated during evening hours for the remainder of the summer to establish potential of whole-house fans to improve interior comfort conditions. The electrical consumption of the fan was measured at both available fan speeds. Measurements revealed that the building interior was 3 - 6°F cooler during the evening hours after the whole house fan was operated. However, data also showed that nighttime humidity levels rose: relative humidity increased from 74% to 83% during the nighttime period where fan-powered ventilation was used. Using the data results, an analysis was performed using Orlando, Florida TMY data to see how limits to whole house ventilation based on humidity and temperature conditions would affect the potential of such a cooling strategy.

Parker, D. S.

1994-01-01T23:59:59.000Z

164

Testing and sampling procedures for geothermal-compressured wells. Final report  

DOE Green Energy (OSTI)

Test wells to tap and sample geothermal-geopressured formations at 15,000 to 20,000 feet in the Gulf Coast area can be drilled routinely utilizing available equipment and methods. Electrical logs, surveys and fluid samplers can be used to obtain accurate and reliable information as to depths, temperatures, pressures, and fluid content of the geopressured formations before the well is completed. But it will be necessary to set casing and flow the well, at least temporarily, to secure fluid production volume and pressure data to evaluate the producibility of the geopressured resource. Electric logging and wireline survey methods are fully developed techniques for measuring the parameters needed to assess a geopressured zone before setting casing. Formation subsidence, though it may be slow to develop, can be measured during radioactivity tracer surveys. The following conclusions are drawn: existing well logging and surveying methods and equipment are generally satisfactory for testing and sampling a geothermal-geopressured resource; no significant areas of research are needed to predict, detect, and evaluate geopressured formations for their potential as geothermal resources. Static and dynamic testing procedures using existing technology are satisfactory to test, sample, and analyze a geopressured reservoir.

Boyd, W.E.

165

Alternative Fuel Evaluation Program: Alternative Fuel Light Duty Vehicle Project - Data collection responsibilities, techniques, and test procedures  

DOE Green Energy (OSTI)

This report describes the data gathering and analysis procedures that support the US Department of Energy's implementation of the Alternative Motor Fuels Act (AMFA) of 1988. Specifically, test procedures, analytical methods, and data protocols are covered. The aim of these collection and analysis efforts, as mandated by AMFA, is to demonstrate the environmental, economic, and performance characteristics of alternative transportation fuels.

Not Available

1992-07-01T23:59:59.000Z

166

Alternative Fuel Evaluation Program: Alternative Fuel Light Duty Vehicle Project - Data collection responsibilities, techniques, and test procedures  

DOE Green Energy (OSTI)

This report describes the data gathering and analysis procedures that support the US Department of Energy`s implementation of the Alternative Motor Fuels Act (AMFA) of 1988. Specifically, test procedures, analytical methods, and data protocols are covered. The aim of these collection and analysis efforts, as mandated by AMFA, is to demonstrate the environmental, economic, and performance characteristics of alternative transportation fuels.

Not Available

1992-07-01T23:59:59.000Z

167

MECHANICAL DRAFT FANS FOR THE MODERN INCINERATOR  

E-Print Network (OSTI)

design and modiftcation. Spe cial blading and fan construction for use under corrosive conditions this will be kept fairly constant by air or water cooling during noral op eration. Since the fan will be designed. Volume control on a single inlet fan can be accomplished with a variable inlet #12;vane, designed

Columbia University

168

Impact-resistant boron/aluminum composites for large fan blades  

SciTech Connect

Blade-like specimens were subjected to static ballistic impact testing to determine their relative FOD impact resistance levels. It was determined that a plus or minus 15 deg layup exhibited good impact resistance. The design of a large solid boron/aluminum fan blade was conducted based on the FOD test results. The CF6 fan blade was used as a baseline for these design studies. The solid boron/aluminum fan blade design was used to fabricate two blades. This effort enabled the assessment of the scale up of existing blade manufacturing details for the fabrication of a large B/Al fan blade. Existing CF6 fan blade tooling was modified for use in fabricating these blades.

Oller, T.L.; Salemme, C.T.; Bowden, J.H.; Doble, G.S.; Melnyk, P.

1977-12-01T23:59:59.000Z

169

Grid Interconnection and Performance Testing Procedures for Vehicle-To-Grid (V2G) Power Electronics: Preprint  

DOE Green Energy (OSTI)

Bidirectional power electronics can add vehicle-to-grid (V2G) capability in a plug-in vehicle, which then allows the vehicle to operate as a distributed resource (DR). The uniqueness of the battery-based V2G power electronics requires a test procedure that will not only maintain IEEE interconnection standards, but can also evaluate the electrical performance of the vehicle working as a DR. The objective of this paper is to discuss a recently published NREL technical report that provides interim test procedures for V2G vehicles for their integration into the electrical distribution systems and for their performance in terms of continuous output power, efficiency, and losses. Additionally, some other test procedures are discussed that are applicable to a V2G vehicle that desires to provide power reserve functions. A few sample test results are provided based on testing of prototype V2G vehicles at NREL.

Kramer, W.; Chakraborty, S.; Kroposki, B.; Hoke, A.; Martin, G.; Markel, T.

2012-03-01T23:59:59.000Z

170

Development of a High Efficiency Ceiling Fan  

E-Print Network (OSTI)

The potential of ceiling fans to improve comfort during the cooling season is well documented (Rohles et al.. 1983; Fairey et al.. 1986). There are at least two cases: In the first where air conditioning is unavailable, adding ceiling fans may significantly improve building comfort and health although actually increasing energy use. However, the more common circumstance is where ceiling fans are used with the objective of providing a higher cooling system thermostat set point with acceptable comfort. Fans can also potentially avoid the use of air conditioning during "swing" seasons. Although studies commonly suggest a 2-6OF increase in the thermostat set point, data from 386 surveyed Central Florida households suggests that although fans are used an average of 13.4 hours per day, no statistically valid difference can be observed in thermostat settings between households using fans and those without them (James et al., 1996). Part of this may be due to the lack of sufficiently wide air distribution coverage within rooms (Rohles et al, 1983; Sonne and Parker, 1998). Studies touting potential cooling savings of up to 40% have usually been sponsored by fan manufacturers (eg. A.D. Little, 1981). These often make unrealistic assumptions such as presuming that occupants are within four feet of a fan with only one fan in use and a 6°F elevation of the thermostat setting. An environmental chamber study by Consumer Reports showed that the long-reported de-stratification benefits when heating are largely unsubstantiated (Consumer Reports. 1993). Thus. benefits from ceiling fans are only to reduce cooling needs and this is completely contingent on sufficient changes in interior comfort to warrant raising of the cooling thermostat. Two other factors must be taken into account in assessing the benefits of fans: their actual energy use and the added internal heat gains produced by the fans during operation. The measured electrical demand of ceiling fans varies between 5 and 115 Watts depending on model and speed selection. A power demand of 40 W at medium speed is probably typical (Chandra, 1985). Thus, a fan used for six months of the year would use 175 kwh. With 4.3 ceiling fans in an average Florida home, this amounts to about 800 kwh of fan energy consumption --about 5% of total electricity use. Also, all of the energy use of fans is eventually converted to heat within the home which must eventually be removed by ventilation air or the cooling system.

Parker, D. S.; Callahan, M. P.; Sonne, J. K.; Su, G. H.; Hibbs, B. D.

2000-01-01T23:59:59.000Z

171

Knowing fans, knowing music : an exploration of fan interaction on Twitter  

E-Print Network (OSTI)

know many local Ritter fans yet” 26 She responded about aI see you're a Buffy fanare you also a Browncoat? : )”The term Browncoats refers to fans of the short-lived sci-fi

McCollum, Nick

2011-01-01T23:59:59.000Z

172

Functional test procedure, Fifth Wheel: SS-R42351, Issue D  

SciTech Connect

This report describes the equipment required for initial assembly/maintenance and inspection/resetting of the Fifth Wheel system. It also gives a step-by-step procedure for initial assembly/maintenance inspection and procedures for resetting the system and Eager-Pac installation. The Fifth Wheel system is associated with a tractor-type vehicle used for materials handling.

1994-07-12T23:59:59.000Z

173

Submitting Organization Hongyou Fan Sandia National Laboratories  

NLE Websites -- All DOE Office Websites (Extended Search)

&24; 2007 R&D 100 Award Entry Form &24; Submitting Organization Hongyou Fan Sandia National Laboratories Advanced Materials Laboratory 1001 University Boulevard SE Albuquerque, NM...

174

Active Noise Control of a Radial Fan.  

E-Print Network (OSTI)

??This thesis work aims at investigating the use of an active noise control (ANC) system on a radial fan. This was done by studying the… (more)

Murthy, Muddala

2009-01-01T23:59:59.000Z

175

The Fan Observatory Bench Optical Spectrograph (FOBOS)  

E-Print Network (OSTI)

The Fan Observatory Bench Optical Spectrograph (FOBOS) is intended for single-object optical spectroscopy at moderate resolution (R~1500-3000) using a fiber-fed, bench-mounted design to maintain stability. Whenever possible, the instrument uses off-the-shelf components to maintain a modest cost. FOBOS supports Galactic astronomy projects that require consistently well-measured (~5 km/sec) radial velocities for large numbers of broadly distributed and relatively bright (Vdesign was optimized for use in the range 470-670 nm. Test data indicate that the instrument is stable and capable of measuring radial velocities with precision better than 3 km/sec at a resolution of R~1500 with minimal calibration overhead.

Jeffrey D. Crane; Steven R. Majewski; Richard J. Patterson; Michael F. Skrutskie; Elena Y. Adams; Peter M. Frinchaboy

2005-02-23T23:59:59.000Z

176

Proposal for a Vehicle Level Test Procedure to Measure Air Conditioning Fuel Use: Preprint  

DOE Green Energy (OSTI)

A procedure is described to measure approximate real-world air conditioning fuel use and assess the impact of thermal load reduction strategies in plug-in hybrid electric vehicles.

Rugh, J.

2010-02-01T23:59:59.000Z

177

Advanced Energy-Efficient Filtration: Fan Filter Unit  

E-Print Network (OSTI)

Efficient Fan- Filter Units, Proceedings of SEMI TechnicalFor Evaluating Fan-Filter Unit Performance – Applications inPerformance of Fan-Filter Units, Version 1.2 (2004, public

Xu, Tengfang

2005-01-01T23:59:59.000Z

178

Advanced Energy-Efficient Filtration: Fan Filter Unit  

E-Print Network (OSTI)

Cleanrooms: Energy Efficient Fan- Filter Units, ProceedingsStandard Method For Evaluating Fan-Filter Unit Performance –Energy Performance of Fan-Filter Units, Version 1.2 (2004,

Xu, Tengfang

2005-01-01T23:59:59.000Z

179

Deviation to the Test Program and Procedures for the 710 Critical Experiment Reactor Control Drum Mockup Experiment  

SciTech Connect

This document describes a deviation from the "Test Program and Procedures for the 710 Critical Experiment Reactor Control Drum Mockup Experiment," TM-64-3-706, which was made in accordance with ITS Standard Practice J80-81 on September 14, 1964. The deviation did not involve a significant change in the safety of the operation.

Sims, F.L.

1964-09-14T23:59:59.000Z

180

10 MWe solar pilot plant, Daggett, California. Flushing and steam blows preoperational test procedure 980. Revision: 0  

Science Conference Proceedings (OSTI)

Prescribed steps are given for flushing and steam blowing the condenser hotwell, deaerator, inline demineralizers, thermal storage subsystem flash tank, and steam lines of the Barstow Solar Pilot Plant. Included are acceptance criteria, precautions, a list of test equipment, initial conditions, procedures and data collection, and system restoration. (LEW)

Williams, D.L.

1980-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications  

DOE Green Energy (OSTI)

The objective of this report is to provide a test plan for V2G testing. The test plan is designed to test and evaluate the vehicle's power electronics capability to provide power to the grid, and to evaluate the vehicle's ability to connect and disconnect from the utility according to a subset of the IEEE Std. 1547 tests.

Chakraborty, S.; Kramer, W.; Kroposki, B.; Martin, G.; McNutt, P.; Kuss, M.; Markel, T.; Hoke, A.

2011-06-01T23:59:59.000Z

182

Operation and Maintenance Guidelines for Draft Fans  

Science Conference Proceedings (OSTI)

The reliability, efficiency, and safety of draft fans in fossil fuel power plants depend on effective operating and maintenance practices. These guidelines systematically present state-of-the-art techniques that utility personnel can use in operation, maintenance, troubleshooting, inspection, and weld repair of major fan components and auxiliary systems.

1999-05-13T23:59:59.000Z

183

Redesign of ceiling fan - adapted to the Scandinavian market.  

E-Print Network (OSTI)

?? The master degree thesis project, at Halmstad University, was made in cooperation with Hunter Fan, one of the leading fan companies on the American… (more)

Eliasson, Anna

2007-01-01T23:59:59.000Z

184

Potential Global Benefits of Improved Ceiling Fan Energy Efficiency  

NLE Websites -- All DOE Office Websites (Extended Search)

Global Benefits of Improved Ceiling Fan Energy Efficiency Title Potential Global Benefits of Improved Ceiling Fan Energy Efficiency Publication Type Report LBNL Report Number...

185

Characterization of air recirculation in multiple fan ventilation systems.  

E-Print Network (OSTI)

??Booster fans, large underground fans, can increase the volumetric efficiency of ventilation systems by helping to balance the pressure and quantity distribution throughout a mine,… (more)

Wempen, Jessica Michelle

2012-01-01T23:59:59.000Z

186

Fan-fold shielded electrical leads  

DOE Patents (OSTI)

Disclosed are fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate. 3 figs.

Rohatgi, R.R.; Cowan, T.E.

1996-06-11T23:59:59.000Z

187

Fan-fold shielded electrical leads  

DOE Patents (OSTI)

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate.

Rohatgi, Rajeev R. (Mountain View, CA); Cowan, Thomas E. (Livermore, CA)

1996-01-01T23:59:59.000Z

188

Interim Test Procedures for Evaluating Electrical Performance and Grid Integration of Vehicle-to-Grid Applications  

SciTech Connect

The objective of this report is to provide a test plan for V2G testing. The test plan is designed to test and evaluate the vehicle's power electronics capability to provide power to the grid, and to evaluate the vehicle's ability to connect and disconnect from the utility according to a subset of the IEEE Std. 1547 tests.

Chakraborty, S.; Kramer, W.; Kroposki, B.; Martin, G.; McNutt, P.; Kuss, M.; Markel, T.; Hoke, A.

2011-06-01T23:59:59.000Z

189

BRITISH COLUMBIA Gully Assessment Procedure  

E-Print Network (OSTI)

strategies and #12;Gully Assessment Procedure Guidebook iv prescriptions designed to accommodate resource).........................................................15 Section 5 Fan Destabilization Potential OPR 37 (1)(c), WLFMR 64 (2)(a......................................30 3. Design and construction of roads across gully systems: when to consult a qualified registered

190

Ceiling Fan and Ceiling Fan Light Kit use in the U.S. Results of a Survey on Amazon Mechanical Turk  

E-Print Network (OSTI)

Intellect, LLC (2011). Ceiling fan consumer survey data fromconsumption from ceiling fans. 5 References Amazon.com. (January/February 2001). Ceiling fans: Fulfilling the energy

Kantner, Colleen L.S.

2013-01-01T23:59:59.000Z

191

Verification/acceptance test plan/procedure for Acromag calibration system  

SciTech Connect

The purpose of this document is to describe and document the test of the Acromag calibration system software. The purpose of this test is to verify that the Acromag Calibration System (ACS) will reliably test the Acromag thermocouple (TC) type input modules and provide a file showing the temperatures at which the modules are tested, the response rom the Acromag station, instrument data, technician data, and date and time of the test. The ACS consists of a thermocouple calibration unit (TCU), a DOS based computer, a hand held resistance temperature detector (RTD) surface probe and connects to a field installed or a bench Acromag unit.

Fordham, C.R.

1994-12-01T23:59:59.000Z

192

Light-Duty Alternative Fuel Vehicles: Federal Test Procedure Emissions Results  

DOE Green Energy (OSTI)

In support of the U.S. Department of Energy's development and deployment of alternative fuels for environmental and national security reasons, NREL has managed a series of light-duty vehicle emissions tests on alternative fuel vehicles (AFVs). The purpose of this report is to give a detailed evaluation of the final emissions test results on vehicles tested on methanol, ethanol, and compressed natural gas.

Kelly, K.; Eudy, L.; Coburn, T.

1999-12-13T23:59:59.000Z

193

Developing Test Procedures for Measuring Stored Thermal Energy in Firefighter Protective Clothing.  

E-Print Network (OSTI)

??This research studied stored thermal energy in fire fighter's turnout systems. It developed a novel laboratory apparatus and test protocols for measuring the contribution of… (more)

Eni, Egbe Uchechi

2005-01-01T23:59:59.000Z

194

Fan System Assessment - End User Training | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fan System Assessment - End User Training Fan System Assessment - End User Training Fan System Assessment - End User Training December 18, 2013 7:30AM to 4:30PM EST Boise, Idaho Optimizing industrial fan systems can take on many forms, but any fan optimization project must meet the needs of the process. This self-paced workshop highlights the benefits of fan system optimization and examines fan system performance characteristics and practical issues concerning measurement data. The session introduces the FSAT software. This powerful analysis software helps you quantify the potential benefits of configuring fan systems for optimal performance, calculate the amount of energy use by your fan system, and estimate fan system efficiency. Learn how the software works, what data is required for FSAT, and how to interpret assessment

195

Cooling with a Whole House Fan | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Cooling with a Whole House Fan Cooling with a Whole House Fan Cooling with a Whole House Fan May 30, 2012 - 6:54pm Addthis Whole house fan installed as part of a home retrofit project in California. | Photo courtesy of Lieko Earle, NREL. Whole house fan installed as part of a home retrofit project in California. | Photo courtesy of Lieko Earle, NREL. What does this mean for me? A whole-house fan may be sufficient to cool your house, at least for part of the year. In many climates, a whole-house fan can save you money and maintain comfort during the cooling season. How does it work? A whole-house fan works by pulling air in through windows and exhausting it through the attic and roof. Whole house cooling using a whole house fan can substitute for an air conditioner most of the year in most climates. Whole house fans combined

196

Laugh out loud in real life : women's humor and fan identity; Women's humor and fan identity.  

E-Print Network (OSTI)

??The emerging field of fan studies has, until recently, been defined only by the research that has taken place within it. Almost universally, this research… (more)

Klink, Madeline LeNore

2010-01-01T23:59:59.000Z

197

Fanning the Flames of Romance: An Exploration of Fan Fiction and the Romance Novel.  

E-Print Network (OSTI)

??Fan fiction and romance novels constitute two bodies of romantic literature being produced for and by women within dramatically different environments. The purpose of this… (more)

Morrissey, Katherine

198

Evaluation of the cooling fan efficiency index.  

E-Print Network (OSTI)

between the cooling effect (measured with a thermal manikin)output is the body cooling effect [5]. Thermal manikins withThermal manikins can be used to measure the fan cooling

Schiavon, Stefano; Melikov, Arsen

2009-01-01T23:59:59.000Z

199

Advanced Manufacturing Office: Training: Fan Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

the tool and presents the basics-and the benefits-of using it to target opportunities for energy savings in your plant. Fan System Assessment - self-paced workshop Availability:...

200

Chemical Testing of Textiles  

Science Conference Proceedings (OSTI)

Chemical Testing of Textiles is edited by Qinguo Fan and covers more subjects than the title implies. These subjects include fiber and yarn identification, ...

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Acceptance test procedure for removal of CS1K circuit switcher block and trip schemes  

Science Conference Proceedings (OSTI)

This supporting document provides a detailed process to test the functions of the circuit switcher, protective relays, alarms, SCADA and 125VDC control logic of 115kV and 13.8kV systems at B3S4 substation following the removal of trip and blocking schemes to Transformer No.1 Circuit Switcher B594.

HACHE, J.M.

1999-08-25T23:59:59.000Z

202

An Innovative Method for Dynamic Characterization of Fan Filter Unit Operation.  

E-Print Network (OSTI)

Filtration: Fan filter units. Final Report, LawrencePerformance of Fan Filter Units, Version 1.3. ” BerkeleyEfficient Fan filter units,” Proceedings of Semiconductor

Xu, Tengfang

2006-01-01T23:59:59.000Z

203

Uranium-series comminution ages of continental sediments: Case study of a Pleistocene alluvial fan  

E-Print Network (OSTI)

of a stream-dominated alluvial fan, San Joaquin valley,on Quaternary fluvial fans, San Joaquin Basin, California,M. , (Eds), Alluvial Fans: Geomorphology, Sedimentology,

Lee, Victoria E.

2010-01-01T23:59:59.000Z

204

Parametric System Curves: Correlations Between Fan Pressure Rise and Flow for Large Commercial Buildings  

E-Print Network (OSTI)

Filter Pressure Loss Model for Fan Energy Calculation in Air2010. “Selecting Efficient Fans”. ASHRAE Journal, Vol. 52,Equipment: Chapter 20 – Fans”. Atlanta, GA: American Society

Sherman, Max

2010-01-01T23:59:59.000Z

205

Coarse-clastic turbidite sedimentation : the neoproterozoic Imsdalen submarine fan complex, Hedmark Basin, South Norway.  

E-Print Network (OSTI)

??The Imsdalen Submarine Fan Complex is a gravel and coarse sand dominated turbidite fan system. The fan complex was deposited in the Neoproterozoic Hedmark rift… (more)

Stalsberg, Martin

2004-01-01T23:59:59.000Z

206

Toxic Characteristic Leaching Procedure (TCLP) Testing of Waste Glass and K-3 Refractory  

Science Conference Proceedings (OSTI)

The U. S. Environmental Protection Agency (EPA) issued revised Resource Conservation and Recovery Act (RCRA) Phase IV Land Disposal Restrictions (LDR's) on May 26 1998. The new regulation requires that any waste characteristically hazardous for the metals As, Ba, Cd, Cr, Pb, Hg, Se, and Ag will have to be treated to meet the LDR Universal Treatment Standards (UTS) for each metal prior to land disposal. Since EPA regulations continue to become more stringent, here-to-fore unpublished TCLP data generated during testing of simulated High Level Waste (HLW) glass, including the Evnironmental Assessment glass and K-3 melter refractory, will be reviewed. The refractory TCLP data compilation includes K-3 refractory in contact with DWPF simulated glass in a pilot scale melter and K-3 refractory in contact with actual mixed waste glass in a 5 ton a day GTS Duratek melter.

Jantzen, C.M.

1999-04-23T23:59:59.000Z

207

Base program interim phase test procedure - Coherent Laser Vision System (CLVS). Final report, September 27, 1994--January 30, 1997  

Science Conference Proceedings (OSTI)

The purpose of the CLVS research project is to develop a prototype fiber-optic based Coherent Laser Vision System suitable for DOE`s EM Robotics program. The system provides three-dimensional (3D) vision for monitoring situations in which it is necessary to update geometrics on the order of once per second. The CLVS project plan required implementation in two phases of the contract, a Base Contract and a continuance option. This is the Test Procedure and test/demonstration results presenting a proof-of-concept for a system providing three-dimensional (3D) vision with the performance capability required to update geometrics on the order of once per second.

NONE

1997-05-01T23:59:59.000Z

208

Fan-less long range alpha detector  

DOE Patents (OSTI)

A fan-less long range alpha detector which operates by using an electrical field between a signal plane and the surface or substance to be monitored for air ions created by collisions with alpha radiation. Without a fan, the detector can operate without the possibility of spreading dust and potential contamination into the atmosphere. A guard plane between the signal plane and the electrically conductive enclosure and maintained at the same voltage as the signal plane, reduces leakage currents. The detector can easily monitor soil, or other solid or liquid surfaces.

MacArthur, Duncan W. (Los Alamos, NM); Bounds, John A. (Los Alamos, NM)

1994-01-01T23:59:59.000Z

209

Fan-less long range alpha detector  

DOE Patents (OSTI)

A fan-less long range alpha detector is disclosed which operates by using an electrical field between a signal plane and the surface or substance to be monitored for air ions created by collisions with alpha radiation. Without a fan, the detector can operate without the possibility of spreading dust and potential contamination into the atmosphere. A guard plane between the signal plane and the electrically conductive enclosure and maintained at the same voltage as the signal plane, reduces leakage currents. The detector can easily monitor soil, or other solid or liquid surfaces. 2 figures.

MacArthur, D.W.; Bounds, J.A.

1994-05-10T23:59:59.000Z

210

Fan Blade Fracture in a Welded Assembly - Programmaster.org  

Science Conference Proceedings (OSTI)

About this Abstract. Meeting, Materials Science & Technology 2013. Symposium, Failure Analysis and Prevention. Presentation Title, Fan Blade Fracture in a ...

211

A Discussion of Procedures and Equipment for the Comprehensive Test Ban Treaty On-Site Inspection Environmental Sampling and Analysis  

SciTech Connect

This paper is intended to serve as a scientific basis to start discussions of the available environmental sampling techniques and equipment that have been used in the past that could be considered for use within the context of the Comprehensive Nuclear-Test-Ban Treaty (CTBT) on-site inspections (OSI). This work contains information on the techniques, equipment, costs, and some operational procedures associated with environmental sampling that have actually been used in the past by the United States for the detection of nuclear explosions. This paper also includes a discussion of issues, recommendations, and questions needing further study within the context of the sampling and analysis of aquatic materials, atmospheric gases, atmospheric particulates, vegetation, sediments and soils, fauna, and drill-back materials.

Wogman, Ned A.; Milbrath, Brian D.; Payne, Rosara F.; Seifert, Carolyn E.; Friese, Judah I.; Miley, Harry S.; Bowyer, Ted W.; Hanlen, Richard C.; Onishi, Yasuo; Hayes, James C.; Wigmosta, Mark S.

2011-02-01T23:59:59.000Z

212

TR-034 Geomorphology March 2006 Coastal fan destabilization  

E-Print Network (OSTI)

the watershed boundary). 3.0 STUDY DESIGN AND METHODS To evaluate fans from a broad range of coastal conditionsTR-034 Geomorphology March 2006 Coastal fan destabilization and forest management by T.H. Millard Columbia V9L 1V2 Citation: Millard, T.H., D.J. Wilford and M.E. Oden. 2006. Coastal fan destabilization

213

Recent Sediments of the Monterey Deep-Sea Fan  

E-Print Network (OSTI)

T Or THE MONTEREV DEEP SEA FAN PLAlE Conpl1.d and ren1our.dO F THE MONTEREY DEEP- SEA FAN by P a t Wilde Berkeley,of segmented alluvial fans in w e s t e r n F r e s n o

Wilde, Pat

1965-01-01T23:59:59.000Z

214

High Efficiency Fans and High Efficiency Electrical Motors  

E-Print Network (OSTI)

Replacing nominal efficient electrical motors with premium efficiency can save on electrical power costs in cotton gins. Connected horsepower load on industrial air fans is approximately 60% of the total horsepower in a typical cotton gin. By replacing old inefficient centrifugal fans with new higher efficiency fans, additional power savings can be achieved.

Breedlove, C. W.

1989-09-01T23:59:59.000Z

215

RFID Interference Test Procedures  

Science Conference Proceedings (OSTI)

... GHz. Active tags contain a power source (eg, battery) and permit higher read ranges and/or lower reader power. Passive ...

2010-10-05T23:59:59.000Z

216

Data Linking with Ontology Alignment Zhengjie Fan  

E-Print Network (OSTI)

Data Linking with Ontology Alignment Zhengjie Fan INRIA & LIG 655, avenue de l'Europe, Montbonnot data on the web, so that users can share information semantically. Then, linking isolated data sets to to be compared, so that it enhances the accuracy of the linking process. I propose a data linking method

217

Lattice congruences, fans and Hopf algebras  

Science Conference Proceedings (OSTI)

We give a unified explanation of the geometric and algebraic properties of two well-known maps, one from permutations to triangulations, and another from permutations to subsets. Furthermore we give a broad generalization of the maps. Specifically for ... Keywords: Malvenuto-Reutenauer Hopf algebra, coexter group, fan poset, hyperplane arrangement, pattern avoidance, permutohedron, poset of regions, weak order

Nathan Reading

2005-05-01T23:59:59.000Z

218

List of Whole House Fans Incentives | Open Energy Information  

Open Energy Info (EERE)

Whole House Fans Incentives Whole House Fans Incentives Jump to: navigation, search The following contains the list of 26 Whole House Fans Incentives. CSV (rows 1 - 26) Incentive Incentive Type Place Applicable Sector Eligible Technologies Active Alliant Energy Interstate Power and Light (Gas and Electric) - Farm Equipment Energy Efficiency Incentives (Iowa) Utility Rebate Program Iowa Agricultural Agricultural Equipment Ceiling Fan Clothes Washers Custom/Others pending approval Dishwasher Doors Heat recovery Lighting Motor VFDs Motors Refrigerators Water Heaters Windows Whole House Fans Room Air Conditioners Ground Source Heat Pumps Yes Alliant Energy Interstate Power and Light - Farm Equipment Energy Efficiency Incentives (Minnesota) Utility Rebate Program Minnesota Agricultural Agricultural Equipment

219

List of Ceiling Fan Incentives | Open Energy Information  

Open Energy Info (EERE)

Fan Incentives Fan Incentives Jump to: navigation, search The following contains the list of 99 Ceiling Fan Incentives. CSV (rows 1 - 99) Incentive Incentive Type Place Applicable Sector Eligible Technologies Active AEP Ohio (Electric) - Residential Energy Efficiency Rebate Program (Ohio) Utility Rebate Program Ohio Residential Building Insulation Ceiling Fan Central Air conditioners Custom/Others pending approval Duct/Air sealing Heat pumps Lighting Motors Programmable Thermostats Windows Yes AEP Ohio (Gas) - Residential Energy Efficiency Rebate Program (Ohio) Utility Rebate Program Ohio Residential Building Insulation Ceiling Fan Central Air conditioners Custom/Others pending approval Dehumidifiers Duct/Air sealing Heat pumps Lighting Motors Programmable Thermostats

220

Power Reduction Scheme of Fans in a Blade System by Considering the Imbalance of CPU Temperatures  

Science Conference Proceedings (OSTI)

In order to develop a data center power efficiency index, we built a test bed of a data center and measured power components and environmental variables in some detail, including the power consumption and temperature of each node, rack and air conditioning ... Keywords: Data center, Power consumption, Power efficiency, CPU temperature, Fan speed

Yuetsu Kodama; Satoshi Itoh; Toshiyuki Shimizu; Satoshi Sekiguchi; Hiroshi Nakamura; Naohiko Mori

2010-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Demonstration of Intelligent Control and Fan Improvements in Computer Room  

NLE Websites -- All DOE Office Websites (Extended Search)

Demonstration of Intelligent Control and Fan Improvements in Computer Room Demonstration of Intelligent Control and Fan Improvements in Computer Room Air Handlers Title Demonstration of Intelligent Control and Fan Improvements in Computer Room Air Handlers Publication Type Report Refereed Designation Unknown LBNL Report Number LBNL-6007E Year of Publication 2012 Authors Coles, Henry C., Steve E. Greenberg, and Corrine Vita Document Number LBNL-6007E Date Published 12/2012 Publisher Lawrence Berkeley National Laboratory City Berkeley, CA Keywords air distribution, building technology and urban systems department, computer room air handler, crah control, data center, data center crah, ec fan, ecm, ecm fan, fan speed control, high tech and industrial systems group, plug fan, variable frequency drive, vfd, wireless control Abstract

222

Analysing International Sports Fan Motivations and Constraints: The Case of Japanese International Sports Fan Tourists and Rugby World Cup Fan Tourists.  

E-Print Network (OSTI)

??The scale of professional sports leagues and mega sports events has expanded recently. Many sports fans travel to foreign countries to watch international events featuring… (more)

Nishio, Tatsuru

2013-01-01T23:59:59.000Z

223

Analytical Solution of a Simplified Transport Problem with Continuous Energy for Testing Monte Carlo Procedures,” this conference  

E-Print Network (OSTI)

A simplified transport problem is presented with continuous energy and neutrons moving only into the +X and –X direction. An exact analytical solution is given with a 1/E energy dependence of the space, direction and energy dependent neutron flux. The source function, which also behaves basically as 1/E has to be modified for a certain energy range if a maximum energy is introduced in the problem. At the cost of more complicated mathematics the total and scattering cross sections and the anisotropy of scattering may very with energy. This model can be implemented in a general purpose Monte Carlo code like MCNP5 without modification, but needs a specially prepared cross section library file. The model can be applied to test Monte Carlo procedures, like the generation of multi-group cross section and scattering matrices which can be calculated analytically from the continuous-energy cross section data. From the adjoint equation the optimum importance function can be derived, which can be used to devise a continuous-energy zero-variance Monte Carlo scheme. Key Words: transport problem, analytical solution, continuous energy, Monte Carlo 1.

J. Eduard Hoogenboom

2007-01-01T23:59:59.000Z

224

HVAC Fans and Dampers Maintenance Guide  

Science Conference Proceedings (OSTI)

Heating, ventilation, and air conditioning (HVAC) systems serve an important function in nuclear power plants because these systems are responsible for maintaining many environmental conditions throughout the facility. Failure of these components can induce undesirable radiological conditions and stressful working conditions, and can compromise the life of qualified equipment. Some HVAC fan and damper failures are preventable by monitoring operating parameters and performing recommended maintenance activ...

1999-08-26T23:59:59.000Z

225

Nonlinear fan instability of electromagnetic waves  

Science Conference Proceedings (OSTI)

This paper studies the linear and nonlinear stages of the fan instability, considering electromagnetic waves of the whistler frequency range interacting resonantly with energetic electron fluxes in magnetized plasmas. The main attention is paid to determine the wave-particle interaction processes that can lead to the excitation of intense electromagnetic waves by nonequilibrium particle distributions involving suprathermal tails, and to explain under what conditions and through what mechanisms they can occur, develop, and saturate. This paper presents and discusses two main processes: (i) the linear fan instability and (ii) the nonlinear process of dynamical resonance merging, which can significantly amplify the energy carried by linearly destabilized waves after they saturate due to particle trapping. This study consists of (i) determining analytically and numerically, for parameters typical of space and laboratory plasmas, the linear growth rates of whistlers excited by suprathermal particle fluxes through the fan instability, as well as the corresponding thresholds and the physical conditions at which the instability can appear, (ii) building a theoretical self-consistent 3D model and a related numerical code for describing the nonlinear evolution of the wave-particle system, and (iii) performing numerical simulations to reveal and characterize the nonlinear amplification process at work, its conditions of development, and its consequences, notably in terms of electromagnetic wave radiation. The simulations show that when the waves have reached sufficient energy levels owing to the linear fan instability, they saturate by trapping particles and due to the complex dynamics of these particles in the electromagnetic fields, the resonant velocities' domains of the waves overlap and merge, meanwhile a strong increase of the wave energy occurs.

Krafft, C. [Laboratoire de Physique des Plasmas, Ecole Polytechnique, 91128 Palaiseau Cedex (France) and University Paris Sud, 91405 Orsay Cedex (France); Volokitin, A. [Space Research Institute (IKI), 117997, 84/32 Profsoyuznaya Str., Moscow (Russian Federation)

2010-10-15T23:59:59.000Z

226

Mass and fans in attached sunspaces  

DOE Green Energy (OSTI)

The effect of thermal storage mass on the performance of an attached sunspace is investigated for a particular design in Boston. Mass in the sunspace and in the adjoining building are compared. Performance is evaluated in terms of temperature conditions in the sunspace and delivery of useful solar heat to the adjoining building. The dependence of the results on the manner of heat delivery is studied. Both natural convection and fan-forced air flow are included.

Jones, R.W.; McFarland, R.D.; Lazarus, G.S.

1982-01-01T23:59:59.000Z

227

Use of fan rig data for the understanding and prediction of fan broadband noise and noise changes due to a variable area nozzle.  

E-Print Network (OSTI)

??This thesis presents the results of the research component of this EngD, entitled Use of fan rig data for the understanding and prediction of fan… (more)

Deane, Eugene Pio

2009-01-01T23:59:59.000Z

228

An Aerodynamic Design Technique For Optimizing Fan Blade Spacing  

E-Print Network (OSTI)

INTRODUCTION Aerodynamic shape optimization involves designing the most efficient shapes of bodies that move through fluids. An optimization algorithm perturbs the shape of an airfoil until it finds the shape which best exhibits a given design objective. For an inverse design technique, this objective is a prescribed aerodynamic distribution, usually the surface pressure distribution. Liebeck pressure distributions [1], for example, have been demonstrated to generate airfoils with high lift to drag ratios. When designing fans, consideration must be given not only to the shape of the fan blades, but also to the distance separating the fan blades. This spacing is defined by the pitch/chord ratio t/l, where the pitch, t, is the distance between fan blades, and the chord, l, is the length of each fan blade. In this work, an inverse algorithm is developed, then used to design fan blade shapes and to find the optimal blade spacing.

T. Rogalsky; R.W. Derksen; Rt N; Rt N; S. Kocabiyik

1999-01-01T23:59:59.000Z

229

Effect of baselevel change on floodplain and fan sediment storage and ephemeral tributary channel morphology, Navarro River, California  

E-Print Network (OSTI)

CHANGE ON FLOODPLAIN AND FAN SEDIMENT STORAGE AND EPHEMERALaffects floodplain and fan sediment storage and smalllowered baselevel on floodplain and fan sediment storage and

Florsheim, Joan L; Mount, Jeffrey F.; Rutten, Luke T.

2000-01-01T23:59:59.000Z

230

Field Study of Exhaust Fans for Mitigating Indoor Air Quality Problems: Final Report to Bonneville Power Administration  

E-Print Network (OSTI)

Using Mechanical Ventilation Exhaust Fans Air-to-Air Heatexpected from exhaust fan A-I Infiltration contribution toIndoor Air Quality -- Exhaust Fan Mitigation" Final Report

Grimsrud, David T.

2009-01-01T23:59:59.000Z

231

Stratigraphic evolution and characteristics of lobes : a high-resolution study of Fan 3, Tanqua Karoo, South Africa.  

E-Print Network (OSTI)

??Fan 3 is one of four basin-floor fans that form part of the Tanqua Karoo Fan Complex in South Africa. It can be subdivided into… (more)

Neethling, J. M.

2009-01-01T23:59:59.000Z

232

Active control of fan noise and vortex shedding.  

E-Print Network (OSTI)

??[Truncated abstract] The subject of fan noise generating mechanisms and its control has been studied intensively over the past few decades as a result of… (more)

Wong, Yee-Jun

2004-01-01T23:59:59.000Z

233

Optimization of Active Noise Control for Small Axial Cooling Fans.  

E-Print Network (OSTI)

??Previous work has shown that active noise control is a feasible solution to attenuate tonal noise radiated by small axial cooling fans, such as those… (more)

Monson, Brian B 1979-

2006-01-01T23:59:59.000Z

234

Characteristics of Residential Housing Units by Ceiling Fans, 2001  

U.S. Energy Information Administration (EIA)

A reporting of the number of housing units using ceiling fans in U.S. households as reported in the 2001 Residential Energy Consumption Survey

235

Water-side Economizer for Non-Fan Cooling Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

changes to the commercial provisions of the 2012 IECC: Water-side Economizer for Non-Fan Cooling Systems R Hart Pacific Northwest National Laboratory January 2013 Proposal...

236

Table 1. Household Characteristics by Ceiling Fans, 2001  

U.S. Energy Information Administration (EIA)

A reporting of the number of housing units using ceiling fans in U.S. households as reported in the 2001 Residential Energy Consumption Survey

237

Deviation of the Test Program and Procedures for the 710 Critical Experiment Reactor Related to Changes in the core Material Volume Fractions  

SciTech Connect

This document describes a deviation from the "Test Program and Procedures for the 710 Critical Experiment Reactor Loading and Rod Calibrations," TM-63-1-702, which was made in accordance with ITS Standard Practice J80-81 on March 13, 1963. The deviation did not involve a significant change in the safety of the operation.

Sims, F.L.

1963-03-13T23:59:59.000Z

238

Cooling Tower Fan Motor Power Optimization Study  

Science Conference Proceedings (OSTI)

Cooling towers are in use at more than 200 major electric generating plants in the United States, representing approximately 800 units and a total of more than 210,000 MW. The auxiliary power consumed by cooling tower fan motors can significantly reduce the net power output of steam-cycle power plants. Cooling tower specifications are established by the economic and operational requirements of maximum unit load and the most demanding environmental conditions expected in the tower’s locale. Since power pl...

2011-11-16T23:59:59.000Z

239

Experimental Modal Analysis on a Rotating Fan Using Tracking-CSLDV  

Science Conference Proceedings (OSTI)

Continuous Scan Laser Doppler Vibrometry (CSLDV) modifies the traditional mode of operation of a vibrometer by sweeping the laser measurement point continuously over the structure while measuring, enabling one to measure spatially detailed mode shapes quickly and minimizing the inconsistencies that can arise if the structure or test conditions change with time. When a periodic scan path is employed, one can decompose the measurement into the response that would have been measured at each point traversed by the laser and obtain the structure's mode shapes and natural frequencies using conventional modal analysis software. In this paper, continuous-scan vibrometry is performed on a rotating fan, using computer controlled mirrors to track the rotating fan blades while simultaneously sweeping the measurement point over the blades. This has the potential to circumvent the difficulty of attaching contact sensors such as strain gauges, which might modify the structure and invalidate the results. In this work, impact excitation was used to excite a 3-blade fan rotating at various speeds, and the blades were scanned with a cloverleaf pattern that captured the bending of all three blades simultaneously. Some specialized signal processing is helpful in minimizing the effect of rotation frequency harmonics in the measurements, and specific scan strategies are needed to avoid those frequencies, both of these issues are discussed in the paper. While noise in the laser vibrometer does pose some difficulty, the results show that several modes could be extracted and that the tracking-CSLDV results agree with measurements obtained from the parked fan.

Gasparoni, Andrea; Castellini, Paolo; Tomasini, Enrico P. [Dipartimento di Meccanica, Universita Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona (Italy); Allen, Matthew S.; Yang Shifei; Sracic, Michael W. [Department of Engineering Physics, University of Wisconsin-Madison, 535 Engineering Research Building, 1500 Engineering Drive, Madison, WI 53706 (United States)

2010-05-28T23:59:59.000Z

240

Standard Methods of Characterizing Performance of Fan Filter Units, Version 3.0  

E-Print Network (OSTI)

power input to operate the FFU at certain airflow conditions, including fan motor, controller, and transformerpower supply to the fan motor, speed control and display device, transformer,power demand shall include fan motor, speed control and display device, transformer,

Xu, Tengfang

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

An Innovative Method for Dynamic Characterization of Fan Filter Unit Operation.  

E-Print Network (OSTI)

power for fan motor, controller, and accessories such as transformerpower demand shall include fan motor, speed control and display device, transformer,power demand shall include the fan, frequency drive motor, speed control device, transformer

Xu, Tengfang

2006-01-01T23:59:59.000Z

242

An Innovative Method for Dynamic Characterization of Fan Filter Unit Operation.  

E-Print Network (OSTI)

that is affected by fan-wheel design, air-path and size,by- 4-ft) fan filter units with various design, operation,differential – the design and control schemes of fan filter

Xu, Tengfang

2006-01-01T23:59:59.000Z

243

Standard Methods of Characterizing Performance of Fan Filter Units, Version 3.0  

E-Print Network (OSTI)

Efficient Filtration: Fan-filter Units. Final Report,Xu. 2007. “The Development of Fan Filter Unit with Flow Rate2007. “Performance of Large Fan Filter Units for Cleanroom

Xu, Tengfang

2007-01-01T23:59:59.000Z

244

“Starring” Madhuri as Durga: The Madhuri Dixit Temple and Performative Fan-Bhakti of Pappu Sardar  

E-Print Network (OSTI)

Devotion and Defiance in Fan Activity. ” In Ravi Vasudevan,Temple and Performative Fan-Bhakti of Pappu Sardar / 415Temple and Performative Fan-Bhakti of Pappu Sardar Shalini

Kakar, Shalini

2009-01-01T23:59:59.000Z

245

Fan-speed-aware scheduling of data intensive jobs  

Science Conference Proceedings (OSTI)

As server processor power densities increase, the cost of air cooling also grows resulting from higher fan speeds. Our measurements show that vibrations induced by fans in high-end servers and its rack neighbors cause a dramatic drop in hard disk bandwidth, ... Keywords: cooling, disk i/o, energy, thermal, vibration

Christine S. Chan; Yanqin Jin; Yen-Kuan Wu; Kenny Gross; Kalyan Vaidyanathan; Tajana `imuni Rosing

2012-07-01T23:59:59.000Z

246

Choosing the right boiler air fans at Weston 4  

SciTech Connect

When it came to choosing the three 'big' boiler air fans - forced draft, induced draft and primary air, the decision revolved around efficiency. The decision making process for fan selection for the Western 4 supercritical coal-fired plant is described in this article. 3 photos.

Spring, N.

2009-04-15T23:59:59.000Z

247

Control system for heat exchangers fans in a refrigeration system  

Science Conference Proceedings (OSTI)

The paper presents a method for controlling evaporator and condenser fans in a refrigeration system. The refrigeration system includes a refrigerant circuit defined by a compressor, a condenser, a throttling device, and an evaporator. The system includes ... Keywords: controlling, fan, refrigeration system, variable frequency drive unit

Cristian Iosifescu; Valeriu Damian; C?lin Ciufudean

2010-05-01T23:59:59.000Z

248

Design and Specification Guidelines for Large Draft Fans and Systems  

Science Conference Proceedings (OSTI)

Design shortcomings in draft fans and related air-gas systems can cause fan failure and costly outages of large fossil fuel power plants. These guidelines will help engineers and manufacturers achieve a better understanding of the design features needed to minimize such failures.

1983-12-01T23:59:59.000Z

249

Condition Monitoring of Fans With Rolling Element Bearings  

Science Conference Proceedings (OSTI)

Data on high-frequency vibration caused by the impacts of bearing pits and spalls can help utilities schedule equipment maintenance. One data collection technique, developed through long-term monitoring of combustion air axial fans at the Pennsylvania Electric Company Homer City station, helps plant personnel anticipate failures of draft fan antifriction bearings by several months.

1988-03-22T23:59:59.000Z

250

Fan Foundation Systems--Analysis and Design Guidelines  

Science Conference Proceedings (OSTI)

Dynamic analysis is the most effective tool for determining the root causes of excessive fan vibration. This study demonstrated the importance of using such analysis in conjunction with a "total systems" approach that considers how the properties of all major fan system components, including foundation, piles, and soil conditions, contribute to vibration.

1986-08-19T23:59:59.000Z

251

Feedback Applications in Active Noise Control for Small Axial Cooling Fans.  

E-Print Network (OSTI)

??Feedback active noise control (ANC) has been applied as a means of attenuating broadband noise from a small axial cooling fan. Such fans are used… (more)

Green, Matthew J 1978-

2006-01-01T23:59:59.000Z

252

Aerodynamic Experiments on a Ducted Fan in Hover and Edgewise Flight.  

E-Print Network (OSTI)

??Ducted fans and ducted rotors have been integrated into a wide range of aerospace vehicles, including manned and unmanned systems. Ducted fans offer many potential… (more)

Myers, Leighton

2009-01-01T23:59:59.000Z

253

Exact solutions to combinatorial optimizations and the traveling baseball fan problem.  

E-Print Network (OSTI)

?? The traveling baseball fan problem is an extension of the classic traveling salesman problem, in which a sports fan wishes to travel to the… (more)

Terrell, Neal D.

2013-01-01T23:59:59.000Z

254

Il fenomeno dei fan nel mercato della musica. Analisi netnografica dei seguaci italiani di Bruce Springsteen.  

E-Print Network (OSTI)

??Lo studio ha ad oggetto la comunità dei fan italiani di Bruce Springsteen. Dopo aver analizzato la letteratura e descritto il fenomeno dei fan e… (more)

Gallo, Sara

2007-01-01T23:59:59.000Z

255

Costs and benefits of energy efficiency improvements in ceiling fans  

SciTech Connect

Ceiling fans contribute significantly to residential electricity consumption, especially in developing countries with warm climates. The paper provides analysis of costs and benefits of several options to improve the efficiency of ceiling fans to assess the global potential for electricity savings and green house gas (GHG) emission reductions. Ceiling fan efficiency can be cost-effectively improved by at least 50% using commercially available technology. If these efficiency improvements are implemented in all ceiling fans sold by 2020, 70 terawatt hours per year could be saved and 25 million metric tons of carbon dioxide equivalent (CO2-e) emissions per year could be avoided, globally. We assess how policies and programs such as standards, labels, and financial incentives can be used to accelerate the adoption of efficient ceiling fans in order to realize potential savings.

Shah, Nihar; Sathaye, Nakul; Phadke, Amol; Letschert, Virginie [Lawrence Berkeley National Lab., CA (United States). Environmental Energy Technology Division] [Lawrence Berkeley National Lab., CA (United States). Environmental Energy Technology Division

2013-10-15T23:59:59.000Z

256

Method for fabricating fan-fold shielded electrical leads  

DOE Patents (OSTI)

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate.

Rohatgi, Rajeev R. (Mountain View, CA); Cowan, Thomas E. (Livermore, CA)

1994-01-01T23:59:59.000Z

257

Method for fabricating fan-fold shielded electrical leads  

DOE Patents (OSTI)

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate. 3 figures.

Rohatgi, R.R.; Cowan, T.E.

1994-12-27T23:59:59.000Z

258

Review: The Dragon & The Elephant: Agricultural and Rural Reforms in China and India edited by Ashok Gulati and Shenggen Fan  

E-Print Network (OSTI)

Ashok Gulati and Shenggen Fan (Eds. ) Reviewed by VarinderIndia Gulati, Ashok and Fan, Shenggen (Eds. ). The Dragon &

Jain, Varinder

2008-01-01T23:59:59.000Z

259

Standard practice for examination of fiberglass reinforced plastic fan blades using acoustic emission  

E-Print Network (OSTI)

1.1 This practice provides guidelines for acoustic emission (AE) examinations of fiberglass reinforced plastic (FRP) fan blades of the type used in industrial cooling towers and heat exchangers. 1.2 This practice uses simulated service loading to determine structural integrity. 1.3 This practice will detect sources of acoustic emission in areas of sensor coverage that are stressed during the course of the examination. 1.4 This practice applies to examinations of new and in-service fan blades. 1.5 This practice is limited to fan blades of FRP construction, with length (hub centerline to tip) of less than 3 m [10 ft], and with fiberglass content greater than 15 % by weight. 1.6 AE measurements are used to detect emission sources. Other nondestructive examination (NDE) methods may be used to evaluate the significance of AE sources. Procedures for other NDE methods are beyond the scope of this practice. 1.7 Units—The values stated in either SI units or inch-pound units are to be regarded separately as sta...

American Society for Testing and Materials. Philadelphia

2010-01-01T23:59:59.000Z

260

Submitting Organization Hongyou Fan Sandia National Laboratories  

NLE Websites -- All DOE Office Websites (Extended Search)

 2007 R&D 100 Award Entry Form  Submitting Organization Hongyou Fan Sandia National Laboratories Advanced Materials Laboratory 1001 University Boulevard SE Albuquerque, NM 87106, USA 505-272-7128 (phone) 505-272-7336 (fax) hfan@sandia.gov AFFIRMATION: I affirm that all information submitted as a part of, or supplemental to, this entry is a fair and accurate represen- tation of this product. Submitter's signature_______________________________ Earl Stromberg Lockheed Martin Aeronautics Mail Zone 2893 PO Box 748 Fort Worth, TX 76101, USA 817-763-7376 (phone) 817-762-6911 (fax) Earl.W.Stromberg@lmco.com Self-Assembling Process for Fabricating Tailored Thin Films This simple, economical nanotechnology coating process enables the development of nanoparticle thin films

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Battery Usage and Thermal Performance of the Toyota Prius and Honda Insight for Various Chassis Dynamometer Test Procedures: Preprint  

DOE Green Energy (OSTI)

This study describes the results from the National Renewable Energy Laboratory's (NREL) chassis dynamometer testing of a 2000 model year Honda Insight and 2001 model year Toyota Prius. The tests were conducted for the purpose of evaluating the battery thermal performance, assessing the impact of air conditioning on fuel economy and emissions, and providing information for NREL's Advanced Vehicle Simulator (ADVISOR).

Kelly, K. J.; Mihalic, M.; Zolot, M.

2001-11-20T23:59:59.000Z

262

Test Procedure for 170.304 e Clinical Decision Support APPROVED Version 1.1 September 24, 2010  

E-Print Network (OSTI)

; and laboratory test results. 1 Department of Health and Human Services, 45 CFR Part 170 Health Information in 45 CFR Part 170 Subpart C of the Final Rule for Health Information Technology: Initial Set of standards, Implementation Specifications, and Certification Criteria for Electronic Health Record Technology

263

Test Procedure for 170.306.c Clinical Decision Support APPROVED Version 1.1 September 24, 2010  

E-Print Network (OSTI)

; and laboratory test results. 1 Department of Health and Human Services, 45 CFR Part 170 Health Information in 45 CFR Part 170 Subpart C of the Final Rule for Health Information Technology: Initial Set of standards, Implementation Specifications, and Certification Criteria for Electronic Health Record Technology

264

Searching optimal shapes for blades of a fan  

E-Print Network (OSTI)

A nonlinear differential equation about optimal shapes for blades of a fan. A boundary value differential problem from engineering, geometrical or physical bonds. A relation between linear profiles and constant speed along the side under flow.

Gianluca Argentini

2008-03-26T23:59:59.000Z

265

Sinewave parameter estimation using the fast fan-chirp transform  

E-Print Network (OSTI)

Sinewave analysis/synthesis has long been an important tool for audio analysis, modification and synthesis. The recently introduced fan-chirp Transform (FChT) [2,3] has been shown to improve the fidelity of sinewave parameter ...

Dunn, Robert B.

266

Variable Speed Fan Retrofits for Computer Room Air Conditioners  

NLE Websites -- All DOE Office Websites (Extended Search)

Variable-Speed Fan Retrofits for Computer-Room Air Conditioners Prepared for the U.S. Department of Energy Federal Energy Management Program Technology Case Study Bulletin By...

267

Use of VFDs on Asphalt Plant Induced Draft Fans  

E-Print Network (OSTI)

Studies of 10 asphalt plants in the Intermountain Region have identified average ID fan energy savings of 68% by controlling airflow using Variable Frequency Drives (VFDs) on the fan motors in place of damper control (inlet or outlet). Average paybacks were 3-5 years before utility incentives. In the 10 plants evaluated, the ID fans accounted for as much as 30% of the total plant electrical consumption. In the majority of these plants the outlet dampers were typically 50%-60% closed. Fan motors ranged from 200 Hp to 500 Hp. With approximately 3,600 existing asphalt plants in operation across the United States, a large opportunity for retrofits exists. Working with manufacturers and owners, a new standard can be established for installing VFDs on all plants.

Anderson, G. R.; Case, P. L.; Lowery, J.

2005-01-01T23:59:59.000Z

268

Crossover distributions at the edge of the rarefaction fan  

E-Print Network (OSTI)

We consider the weakly asymmetric limit of simple exclusion process with drift to the left, starting from step Bernoulli initial data with $\\rho_-fan. We study the fluctuations of the process observed along slopes in the fan, which are given by the Hopf--Cole solution of the Kardar-Parisi-Zhang (KPZ) equation, with appropriate initial data. For slopes strictly inside the fan, the initial data is a Dirac delta function and the one point distribution functions have been computed in [Comm. Pure Appl. Math. 64 (2011) 466-537] and [Nuclear Phys. B 834 (2010) 523-542]. At the edge of the rarefaction fan, the initial data is one-sided Brownian. We obtain a new family of crossover distributions giving the exact one-point distributions of this process, which converge, as $T\

Ivan Corwin; Jeremy Quastel

2010-06-07T23:59:59.000Z

269

A Tip Driven Fan Based on SERAPHIM Technology  

SciTech Connect

SERAPHIM technology appears capable of efficiently driving a tip driven fan. If the motor is powered using an inverter and resonant circuit, the size and weight could be considerably below that of a comparable rotary electric motor.

MARDER, BARRY M.

2002-01-01T23:59:59.000Z

270

Property:Building/SPElectrtyUsePercCirculationFans | Open Energy  

Open Energy Info (EERE)

SPElectrtyUsePercCirculationFans SPElectrtyUsePercCirculationFans Jump to: navigation, search This is a property of type String. Circulation fans Pages using the property "Building/SPElectrtyUsePercCirculationFans" Showing 25 pages using this property. (previous 25) (next 25) S Sweden Building 05K0001 + 18.6715328229 + Sweden Building 05K0002 + 0.0 + Sweden Building 05K0003 + 3.84924044288 + Sweden Building 05K0004 + 13.5679722118 + Sweden Building 05K0005 + 10.115947775 + Sweden Building 05K0006 + 10.4348038368 + Sweden Building 05K0007 + 3.09034005771 + Sweden Building 05K0008 + 1.5024342653 + Sweden Building 05K0009 + 13.4365662073 + Sweden Building 05K0010 + 0.0 + Sweden Building 05K0011 + 2.75323793817 + Sweden Building 05K0012 + 15.8993705073 + Sweden Building 05K0013 + 1.11354848212 +

271

Property:Building/SPElectrtyUsePercFans | Open Energy Information  

Open Energy Info (EERE)

SPElectrtyUsePercFans SPElectrtyUsePercFans Jump to: navigation, search This is a property of type String. Fans Pages using the property "Building/SPElectrtyUsePercFans" Showing 25 pages using this property. (previous 25) (next 25) S Sweden Building 05K0001 + 7.29539104961 + Sweden Building 05K0002 + 16.7673965927 + Sweden Building 05K0003 + 27.9131959869 + Sweden Building 05K0004 + 12.2479817873 + Sweden Building 05K0005 + 29.1925346224 + Sweden Building 05K0006 + 15.8653423601 + Sweden Building 05K0007 + 12.809449974 + Sweden Building 05K0008 + 22.2979541594 + Sweden Building 05K0009 + 22.7088540206 + Sweden Building 05K0010 + 13.3738132017 + Sweden Building 05K0011 + 25.1040933765 + Sweden Building 05K0012 + 22.6542018423 + Sweden Building 05K0013 + 24.3166483485 +

272

Designing Axial Flow Fan for Flow and Noise  

E-Print Network (OSTI)

A comprehensive finite element methodology is developed to predict the compressible flow performance of a non-symmetric 7-blade axial flow fan, and to quantify the source strength and sound pressure levels at any location in the system. The acoustic and flow performances of the fan are predicted simultaneously using a computational aero-acoustic technique combining transient flow analysis and noise propagation. The calculated sound power levels compare favorably with the measured sound power data per AMCA 300-96 code.

Subrata Roy; Phillip Cho; Fred Périé; International Off-highway

1999-01-01T23:59:59.000Z

273

Emergency Procedures  

Energy.gov (U.S. Department of Energy (DOE))

Note: This page is pending deletion, please refer to the Safety and health main page for emergency procedure information:

274

Best Practice for Energy Efficient Cleanrooms: Fan-FilterUnits  

Science Conference Proceedings (OSTI)

The HVAC systems in cleanrooms may use 50 percent or more of the total cleanroom energy use. Fan energy use accounts for a significant portion (e.g., over 50%) of the HVAC energy use in cleanrooms such as ISO Classes 3, 4, or 5. Three types of air-handling systems for recirculating airflows are commonly used in cleanrooms: (1) fan-tower systems with pressurized plenum, (2) ducted HEPA systems with distributed-fans, and (3) systems with fan-filter units. Because energy efficiency of the recirculation systems could vary significantly from system type to system type, optimizing aerodynamic performance in air recirculation systems appears to be a useful approach to improve energy efficiency in cleanrooms. Providing optimal airflows through careful planning, design and operation, including air change rate, airflow uniformity, and airflow speed, is important for controlling particle contamination in cleanrooms. In practice, the use of fan-filter units (FFUs) in the air-handling system is becoming more and more popular because of this type of system may offer a number of advantages. Often modular and portable than traditional recirculation airflow systems, FFUs are easier to install, and can be easily controlled and monitored to maintain filtration performance. Energy efficiency of air handling systems using fan-filter units can, however, be lower than their counterparts and may vary significantly from system to system because of the difference in energy performance, airflow paths, and the operating conditions of FFUs.

Xu, Tengfang

2005-06-15T23:59:59.000Z

275

Induced draft fan innovation for heat recovery steam generators  

SciTech Connect

A first of its kind, induced draft (ID) heat recovery steam generators (HRSG) have been in service at a cogeneration facility since 1991. A preliminary engineering study considered a forced draft (FD) fan to supply combustion air to the HRSG duct burners (when the combustion turbine (CT) is out of service) as a traditional design; however, the study indicated that the FD fan may require the HRSG duct burner to be shut off following a CT trip and re-ignited after the FD fan was in service. Although the induced draft HRSG design cost more than the FD fan design, the induced draft design has improved the cogeneration facility's steam generation reliability by enabling the HRSG to remain in service following a CT trip. This paper briefly summarizes the preliminary engineering study that supported the decision to select the ID fan design. The paper also discusses the control system that operates the fresh-air louvers, duct burners, HRSG, and ID fan during a CT trip. Startup and operating experiences are presented that demonstrate the effectiveness of the design. Lessons learned are also summarized for input into future induced draft HRSG designs.

Beasley, O.W.; Hutchins, E.C. (Oklahoma Gas and Electric Co., Oklahoma City, OK (United States)); Predick, P.R.; Vavrek, J.M. (Sargent and Lundy, Chicago, IL (United States))

1994-04-01T23:59:59.000Z

276

Ceiling Fan and Ceiling Fan Light Kit use in the U.S. Results of a Survey on Amazon Mechanical Turk  

E-Print Network (OSTI)

air conditioning .31   3.7   Impact of ceiling fans on air conditioningowners increased the air conditioning thermostat temperature

Kantner, Colleen L.S.

2013-01-01T23:59:59.000Z

277

Test of Significance when data are curves  

E-Print Network (OSTI)

The adaptive Neyman test in Section 3.2 is applied to this20, 2071-2086. Fan, J. 1996, Test of signi cance based on254-261. Fisher, R.A. 1929, Tests of signi cance in harmonic

Jianqing Fan; S. K. Lin

2011-01-01T23:59:59.000Z

278

HVAC BESTEST: A Procedure for Testing the Ability of Whole-Building Energy Simulation Programs to Model Space Conditioning Equipment: Preprint  

DOE Green Energy (OSTI)

Validation of Building Energy Simulation Programs consists of a combination of empirical validation, analytical verification, and comparative analysis techniques (Judkoff 1988). An analytical verification and comparative diagnostic procedure was developed to test the ability of whole-building simulation programs to model the performance of unitary space-cooling equipment that is typically modeled using manufacturer design data presented as empirically derived performance maps. Field trials of the method were conducted by researchers from nations participating in the International Energy Agency (IEA) Solar Heating and Cooling (SHC) Programme Task 22, using a number of detailed hourly simulation programs from Europe and the United States, including: CA-SIS, CLIM2000, PROMETHEUS, TRNSYS-TUD, and two versions of DOE-2.1E. Analytical solutions were also developed for the test cases.

Neymark, J,; Judkoff, R.; Knabe, G.; Le, H.-T.; Durig, M.; Glass, A.; Zweifel, G.

2001-07-03T23:59:59.000Z

279

Test procedures and protocols: Their relevance to the figure of merit for thermal distribution systems. Volume 1: Informal report  

Science Conference Proceedings (OSTI)

A conceptual framework is developed that categorizes measurement protocols for forced-air thermal distribution systems in small buildings. This framework is based on the distinction between two generic approaches. The {open_quote}system-comparison{close_quote} approach seeks to determine, via a pair of whole-house energy-use measurements, the difference in energy use between the house with the as-found duct system and the same house with no energy losses attributable to the thermal distribution system. The {open_quote}component loss-factor{close_quote} approach identifies and measures the individual causes of duct losses, and then builds up a value for the net overall duct efficiency, usually with the help of computer simulation. Examples of each approach are analyzed and related to a proposed Figure of Merit for thermal distribution systems. This Figure of Merit would serve as the basis for a Standard Method of Test analogous to those already in place for furnaces, boilers, air conditioners, and heat pumps.

Andrews, J.W.

1993-09-01T23:59:59.000Z

280

TEST PLAN AND PROCEDURE FOR THE EXAMINATION OF TANK 241-AY-101 MULTI-PROBE CORROSION MONITORING SYSTEM  

SciTech Connect

This test plan describes the methods to be used in the forensic examination of the Multi-probe Corrosion Monitoring System (MPCMS) installed in the double-shell tank 241-AY-101 (AY-101). The probe was designed by Applied Research and Engineering Sciences (ARES) Corporation. The probe contains four sections, each of which can be removed from the tank independently (H-14-107634, AY-101 MPCMS Removable Probe Assembly) and one fixed center assembly. Each removable section contains three types of passive corrosion coupons: bar coupons, round coupons, and stressed C-rings (H-14-l07635, AY-101 MPCMS Details). Photographs and weights of each coupon were recorded and reported on drawing H-14-107634 and in RPP-RPT-40629, 241-AY-101 MPCMS C-Ring Coupon Photographs. The coupons will be the subject of the forensic analyses. The purpose of this examination will be to document the nature and extent of corrosion of the 29 coupons. This documentation will consist of photographs and photomicrographs of the C-rings and round coupons, as well as the weights of the bar and round coupons during corrosion removal. The total weight loss of the cleaned coupons will be used in conjunction with the surface area of each to calculate corrosion rates in mils per year. The bar coupons were presumably placed to investigate the liquid-air-interface. An analysis of the waste level heights in the waste tank will be investigated as part of this examination.

WYRWAS RB; PAGE JS; COOKE GS

2012-04-19T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Developing Fatigue Pre-crack Procedure to Evaluate Fracture Toughness of Pipeline Steels Using Spiral Notch Torsion Test  

SciTech Connect

The spiral notch torsion test (SNTT) has been utilized to investigate the crack growth behavior of X52 steel base and welded materials used for hydrogen infrastructures. The X52 steel materials are received from a welded pipe using friction stir welding techniques. Finite element models were established to study the crack growth behavior of steel SNTT steel samples, which were assumed to be isotropic material. A series SNTT models were set up to cover various crack penetration cases, of which the ratios between crack depth to diameter (a/D ratio) ranging from 0.10 to 0.45. The evolution of compliance and energy release rates in the SNTT method have been investigated with different cases, including different geometries and materials. Indices of characteristic compliance and energy release rates have been proposed. Good agreement has been achieved between predictions from different cases in the same trend. These work shed lights on a successful protocol for SNTT application in wide range of structural materials. The further effort needed for compliance function development is to extend the current developed compliance function to the deep crack penetration arena, in the range of 0.55 to 0.85 to effectively determine fracture toughness for extremely tough materials.

Wang, Jy-An John [ORNL; Tan, Ting [ORNL; Jiang, Hao [ORNL; Zhang, Wei [ORNL; Feng, Zhili [ORNL

2012-10-01T23:59:59.000Z

282

Modelling the architecture of distal sand-rich lobe deposits : an example from Fan 2, Skoorsteenberg Formation, Tanqua Karoo, South Africa.  

E-Print Network (OSTI)

??Fan 2, one of five submarine fan systems of the Tanqua fan complex in the south-western Karoo Basin, South Africa, is subdivided into Lower, Middle… (more)

Steyn, Rochelle

2009-01-01T23:59:59.000Z

283

CMS Procedure  

Science Conference Proceedings (OSTI)

... Tabletop Exercise. Tailoring. Tape Management System. Technical Safeguard. Tempest. Test Plan. Test. Threat Agent. Threat Analysis. ...

2009-06-30T23:59:59.000Z

284

Photo of the Week: Fan-tastic | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Fan-tastic Fan-tastic Photo of the Week: Fan-tastic August 17, 2012 - 10:30am Addthis In Jonesboro, Arkansas, a Nordex USA employee stands between utility-scale components that will eventually make up a completed wind turbine. Under the Recovery Act, Nordex USA received a tax credit to assist in the creation of the Jonesboro manufacturing facility, which opened in October 2010. | Photo courtesy of Nordex USA. In Jonesboro, Arkansas, a Nordex USA employee stands between utility-scale components that will eventually make up a completed wind turbine. Under the Recovery Act, Nordex USA received a tax credit to assist in the creation of the Jonesboro manufacturing facility, which opened in October 2010. | Photo courtesy of Nordex USA. Sarah Gerrity Sarah Gerrity Multimedia Editor, Office of Public Affairs

285

Cooling Tower Energy Conservation Through Hydraulic Fan Drives  

E-Print Network (OSTI)

Many companies offer gearboxes, shafts, and couplings for cooling tower fan drives, with little or no innovation. These companies have traditionally been purchased with an emphasis on cost and not "Return on Investment!" In the past, when energy conservation or "Return on Investment" was emphasized, the only alternative was to add an expensive frequency inverter for variable speed control. This meant expensive rewiring, placing additional controls in an already crowded control room, or constructing a special building for them. However, with H.E.M.'s patented Hydraulic Fan Drive, one receives variable speed control and more efficiency for approximately the price of a mechanical drive. The new, more efficient Hydraulic Drive allows for a variable speed control and the ability to sense water temperature to control fan speed.

Dickerson, J.

1991-06-01T23:59:59.000Z

286

Field Study of Exhaust Fans for Mitigating Indoor Air Quality Problems: Final Report to Bonneville Power Administration  

E-Print Network (OSTI)

operation at low fan speeds (LBL design) and operation --continuously design in the heat exchangers exhaust fans onDesign The basic objective of this project, to study the effects of exhaust fan

Grimsrud, David T.

2009-01-01T23:59:59.000Z

287

Blue fan palm distribution and seed removal patterns in three desert oases of northern Baja California, Mexico  

E-Print Network (OSTI)

DOI 10.1007/s11258-009-9682-4 Blue fan palm distribution anddistribution patterns of the blue fan palm, Brahea armata,i) the levels of blue fan palm seed removal by vertebrates

Wehncke, Elisabet V.; López-Medellín, Xavier; Ezcurra, Exequiel

2010-01-01T23:59:59.000Z

288

Set Top Boxes Test Procedure  

NLE Websites -- All DOE Office Websites (Extended Search)

Commission. Jessie F. Quichocho, Division of Policy and Rulemaking, Office of Nuclear Reactor Regulation. FR Doc. 2011-32389 Filed 12-15-11; 8:45 am BILLING CODE 7590-01-P...

289

Experimental Evaluation of Installed Cooking Exhaust Fan Performance  

NLE Websites -- All DOE Office Websites (Extended Search)

Experimental Evaluation of Installed Cooking Exhaust Fan Performance Experimental Evaluation of Installed Cooking Exhaust Fan Performance Title Experimental Evaluation of Installed Cooking Exhaust Fan Performance Publication Type Report LBNL Report Number LBNL-4183E Year of Publication 2010 Authors Singer, Brett C., William W. Delp, and Michael G. Apte Publisher Lawrence Berkeley National Laboratory City Berkeley Keywords airflow & pollutant transport group, cooktop, energy analysis and environmental impacts department, gas burners, indoor air quality, indoor environment department, kitchen, nitrogen dioxide, oven, pollutant emissions, range hood, residential, source control, task ventilation, technology, sustainability and impact assessment group Abstract The installed performance of cooking exhaust fans was evaluated through residential field experiments conducted on a sample of 15 devices varying in design and other characteristics. The sample included two rear downdraft systems, two under-cabinet microwave over range (MOR) units, three different installations of an under-cabinet model with grease screens across the bottom and no capture hood, two devices with grease screens covering the bottom of a large capture hood (one under-cabinet, one wall-mount chimney), four under-cabinet open hoods, and two open hoods with chimney mounts over islands. Performance assessment included measurement of airflow and sound levels across fan settings and experiments to quantify the contemporaneous capture efficiency for the exhaust generated by natural gas cooking burners. Capture efficiency is defined as the fraction of generated pollutants that are removed through the exhaust and thus not available for inhalation of household occupants. Capture efficiency (CE) was assessed for various configurations of burner use (e.g. single front, single back, combination of one front and one back, oven) and fan speed setting. Measured airflow rates were substantially lower than the levels noted in product literature for many of the units. This shortfall was observed for several units costing in excess of $1000. Capture efficiency varied widely (from <5% to roughly 100%) across devices and across conditions for some devices. As expected, higher capture efficiencies were achieved with higher fan settings and the associated higher air flow rates. In most cases, capture efficiencies were substantially higher for rear burners than for front burners. The best and most consistent performance was observed for open hoods that covered all cooktop burners and operated at higher airflow rates. The lowest capture efficiencies were measured when a front burner was used with a rear backdraft system or with lowest fan setting for above the range systems that do not cover the front burners.

290

Income Tax Deduction for Solar-Powered Roof Vents or Fans (Indiana...  

Open Energy Info (EERE)

1232012 References DSIRE1 Summary Indiana allows taxpayers to take a deduction on solar-powered roof fans (or vent, also sometimes called an attic fan) installed in a home...

291

Income Tax Deduction for Solar-Powered Roof Vents or Fans  

Energy.gov (U.S. Department of Energy (DOE))

Indiana allows taxpayers to take a deduction on solar-powered roof fans (or vent, also sometimes called an attic fan) installed in a home that the taxpayer owns or leases. The deduction is for 50%...

292

Laugh out loud in real life : women's humor and fan identity  

E-Print Network (OSTI)

The emerging field of fan studies has, until recently, been defined only by the research that has taken place within it. Almost universally, this research focuses on self-identified fans. However, scholars are beginning ...

Klink, Madeline LeNore

2010-01-01T23:59:59.000Z

293

Experimental investigation of a six inch diameter, four inch span cross-flow fan .  

E-Print Network (OSTI)

??Investigations into the use of a cross-flow fan as a potential source of propulsion and lift have arisen due to the cross-flow fan's geometry, light… (more)

Ulvin, Jessica M.

2008-01-01T23:59:59.000Z

294

Improve the Energy Efficiency of Fan Systems, Software Tools for Industry, Industrial Technologies Program (ITP) (Fact Sheet)  

Science Conference Proceedings (OSTI)

This fact sheet describes how the Industrial Technologies Program Fan System Assessment Tool (FSAT) can help quantify energy consumption and savings opportunities in industrial fan systems.

Not Available

2008-12-01T23:59:59.000Z

295

An Initial Study on Applying Active Noise Control to an Insulated Box Fan Used in Ventilation System Applications.  

E-Print Network (OSTI)

??In many different applications and buildings fans are used to remove unwanted and used air. These fans often generate broadband and tonal noise. Commonly, passive… (more)

Larsson, Martin; Johansson, Sven; Muddala, S.M.; Gafar, A.E.; Håkansson, Lars; Tarkka, Juhani

2009-01-01T23:59:59.000Z

296

A Comparison of US and Chinese EV Battery Testing Protocols  

NLE Websites -- All DOE Office Websites (Extended Search)

US and Chinese EV US and Chinese EV Battery Testing Protocols: Results D. Robertson, 1 J. Christophersen, 2 Fang Wang, 3 Fan Bin, 3 I. Bloom 1 US/China Electric Vehicle Initiative Meeting August 23-24, 2012 Boston, MA 1 Argonne National Laboratory 2 Idaho National Laboratory 3 CATARC A Comparison of US and Chinese Battery Testing Protocols  Battery testing is a time-consuming and costly process  There are parallel testing efforts, such as those in the US and China  These efforts may be better leveraged through international collaboration  The collaboration may establish standardized, accelerated testing procedures and will allow battery testing organizations to cooperate in the analysis of the resulting data  In turn, the collaboration may accelerate electric vehicle development and

297

A satisfiability algorithm for constant depth boolean circuits with unbounded fan-in gates  

E-Print Network (OSTI)

Boolean Circuits with Unbounded Fan-In Gates A dissertationAC 0 by allowing unbounded fan-in M OD m 1 , . . . , M OD mSince each gate in ? has fan-in at most k and ? has depth D

Matthews, William Grant

2011-01-01T23:59:59.000Z

298

Laboratory evaluation of fan/filter units' aerodynamic and energy performance  

SciTech Connect

The paper discusses the benefits of having a consistent testing method to characterize aerodynamic and energy performance of FFUs. It presents evaluation methods of laboratory-measured performance of ten relatively new, 1220 mm x 610 mm (or 4 ft x 2 ft) fan-filter units (FFUs), and includes results of a set of relevant metrics such as energy performance indices (EPI) based upon the sample FFUs tested. This paper concludes that there are variations in FFUs' performance, and that using a consistent testing and evaluation method can generate compatible and comparable FFU performance information. The paper also suggests that benefits and opportunities exist for our method of testing FFU energy performance to be integrated in future recommended practices.

Xu, Tengfang; Jeng, Ming-Shan

2004-07-27T23:59:59.000Z

299

The Forming of AISI 409 sheets for fan blade manufacturing  

SciTech Connect

The necessity of adapting the standardized fan models to conditions of higher temperature has emerged due to the growth of concern referring to the consequences of the gas expelling after the Mont Blanc tunnel accident in Italy and France, where even though, with 100 fans in operation, 41 people died. The objective of this work is to present an alternative to the market standard fans considering a new technology in constructing blades. This new technology introduces the use of the stainless steel AISI 409 due to its good to temperatures of gas exhaust from tunnels in fire situation. The innovation is centered in the process of a deep drawing of metallic sheets in order to keep the ideal aerodynamic superficies for the fan ideal performance. Through the impression of circles on the sheet plane it is shown, experimentally, that, during the pressing process, the more deformed regions on the sheet plane of the blade can not reach the deformation limits of the utilized sheet material.

Foroni, F. D.; Menezes, M. A.; Moreira Filho, L. A. [ITA - Aeronautic Technological Institute, IEM, Praca Mal. Eduardo Gomes, 50 - Vila das Acacias - S. J. Campos, Brasil - CEP 1228-900 (Brazil)

2007-04-07T23:59:59.000Z

300

Experimental Evaluation of Installed Cooking Exhaust Fan Performance  

SciTech Connect

The installed performance of cooking exhaust fans was evaluated through residential field experiments conducted on a sample of 15 devices varying in design and other characteristics. The sample included two rear downdraft systems, two under-cabinet microwave over range (MOR) units, three different installations of an under-cabinet model with grease screens across the bottom and no capture hood, two devices with grease screens covering the bottom of a large capture hood (one under-cabinet, one wall-mount chimney), four under-cabinet open hoods, and two open hoods with chimney mounts over islands. Performance assessment included measurement of airflow and sound levels across fan settings and experiments to quantify the contemporaneous capture efficiency for the exhaust generated by natural gas cooking burners.Capture efficiency is defined as the fraction of generated pollutants that are removed through the exhaust and thus not available for inhalation of household occupants. Capture efficiency (CE) was assessed for various configurations of burner use (e.g., single front, single back, combination of one front and one back, oven) and fan speed setting. Measured airflow rates were substantially lower than the levels noted in product literature for many of the units. This shortfall was observed for several units costing in excess of $1000. Capture efficiency varied widely (from<5percent to roughly 100percent) across devices and across conditions for some devices. As expected, higher capture efficiencies were achieved with higher fan settings and the associated higher air flow rates. In most cases, capture efficiencies were substantially higher for rear burners than for front burners. The best and most consistent performance was observed for open hoods that covered all cooktop burners and operated at higher airflow rates. The lowest capture efficiencies were measured when a front burner was used with a rear backdraft system or with lowest fan setting for above the range systems that do not cover the front burners.

Singer, Brett C.; Delp, William W.; Apte, Michael G.

2010-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Energy Efficient Single Stack Exhaust Fan Systems (E3S3F)  

E-Print Network (OSTI)

This paper first investigates the fan energy performance of a constant air volume exhaust system. Two single stack energy efficient exhaust fan systems (E3S3F) are presented. The E3S3F-I has the static pressure sensor located at the inlet of the exhaust fan. It has been found to consume up to 15% less fan power than conventional constant air volume exhaust systems. The E3S3F-II uses a variable speed device to maintain the static pressure at the entrance of the stack. It consumes up to 60% less fan power than conventional constant volume exhaust systems.

Wang, G.; Liu, M.

2001-01-01T23:59:59.000Z

302

Mobile Energy Laboratory Procedures  

SciTech Connect

Pacific Northwest Laboratory (PNL) has been tasked to plan and implement a framework for measuring and analyzing the efficiency of on-site energy conversion, distribution, and end-use application on federal facilities as part of its overall technical support to the US Department of Energy (DOE) Federal Energy Management Program (FEMP). The Mobile Energy Laboratory (MEL) Procedures establish guidelines for specific activities performed by PNL staff. PNL provided sophisticated energy monitoring, auditing, and analysis equipment for on-site evaluation of energy use efficiency. Specially trained engineers and technicians were provided to conduct tests in a safe and efficient manner with the assistance of host facility staff and contractors. Reports were produced to describe test procedures, results, and suggested courses of action. These reports may be used to justify changes in operating procedures, maintenance efforts, system designs, or energy-using equipment. The MEL capabilities can subsequently be used to assess the results of energy conservation projects. These procedures recognize the need for centralized NM administration, test procedure development, operator training, and technical oversight. This need is evidenced by increasing requests fbr MEL use and the economies available by having trained, full-time MEL operators and near continuous MEL operation. DOE will assign new equipment and upgrade existing equipment as new capabilities are developed. The equipment and trained technicians will be made available to federal agencies that provide funding for the direct costs associated with MEL use.

Armstrong, P.R.; Batishko, C.R.; Dittmer, A.L.; Hadley, D.L.; Stoops, J.L.

1993-09-01T23:59:59.000Z

303

Variable Speed Fan Retrofits for Computer Room Air Conditioners  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Variable-Speed Fan Variable-Speed Fan Retrofits for Computer-Room Air Conditioners Prepared for the U.S. Department of Energy Federal Energy Management Program Technology Case Study Bulletin By Lawrence Berkeley National Laboratory Steve Greenberg September 2013 2 Contacts Steve Greenberg Lawrence Berkeley National Laboratory One Cyclotron Road, 90R3111 Berkeley, California 94720 (510) 486-6971 segreenberg@lbl.gov For more information on FEMP, please contact: Will Lintner, P.E., CEM Federal Energy Management Program U.S. Department of Energy 1000 Independence Ave. S.W. Washington, D. C. 20585-0121 (202) 586-3120 william.lintner@ee.doe.gov 3 Acknowledgements EPRI: Dennis Symanski, Brian Fortenbery Synapsense: Garret Smith, Patricia Nealon Vigilent: Corinne Vita

304

Experimental Evaluation of Installed Cooking Exhaust Fan Performance  

Science Conference Proceedings (OSTI)

The installed performance of cooking exhaust fans was evaluated through residential field experiments conducted on a sample of 15 devices varying in design and other characteristics. The sample included two rear downdraft systems, two under-cabinet microwave over range (MOR) units, three different installations of an under-cabinet model with grease screens across the bottom and no capture hood, two devices with grease screens covering the bottom of a large capture hood (one under-cabinet, one wall-mount chimney), four under-cabinet open hoods, and two open hoods with chimney mounts over islands. Performance assessment included measurement of airflow and sound levels across fan settings and experiments to quantify the contemporaneous capture efficiency for the exhaust generated by natural gas cooking burners.Capture efficiency is defined as the fraction of generated pollutants that are removed through the exhaust and thus not available for inhalation of household occupants. Capture efficiency (CE) was assessed for various configurations of burner use (e.g., single front, single back, combination of one front and one back, oven) and fan speed setting. Measured airflow rates were substantially lower than the levels noted in product literature for many of the units. This shortfall was observed for several units costing in excess of $1000. Capture efficiency varied widely (fromfan settings and the associated higher air flow rates. In most cases, capture efficiencies were substantially higher for rear burners than for front burners. The best and most consistent performance was observed for open hoods that covered all cooktop burners and operated at higher airflow rates. The lowest capture efficiencies were measured when a front burner was used with a rear backdraft system or with lowest fan setting for above the range systems that do not cover the front burners.

Singer, Brett C.; Delp, William W.; Apte, Michael G.

2010-11-01T23:59:59.000Z

305

Generator Fan/Blower Design, Inspection, and Maintenance  

Science Conference Proceedings (OSTI)

Turbo-generator rotor cooling fans and blowers are highly stressed components of a generator rotor. As such, their failures can result in expensive damages and extended outages. This best practices document provides guidelines that help plant managers understand potential failure mechanisms and their root causes, anticipate issues before failures occur, and prepare inspection and contingency plans.The guidelines are applicable to both nuclear and fossil turbo-generator rotors. Both axial ...

2012-12-13T23:59:59.000Z

306

Turning on the Fan and Turning off the A/C | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Turning on the Fan and Turning off the A/C Turning on the Fan and Turning off the A/C Turning on the Fan and Turning off the A/C September 20, 2010 - 3:00pm Addthis As part of some recent money- and energy-savings improvements I've been making to my home, a couple of weeks ago I installed a ceiling fan in my main living room. Chris Stewart Senior Communicator at DOE's National Renewable Energy Laboratory As part of some recent money- and energy-savings improvements I've been making to my home, a couple of weeks ago I installed a ceiling fan in my main living room. Part of my research led me to understand how ceiling fans are considered the most effective fans compared among table fans, floor fans, and fans mounted to poles or walls because they effectively circulate the air in a room to create a draft throughout the room.

307

Turning on the Fan and Turning off the A/C | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Turning on the Fan and Turning off the A/C Turning on the Fan and Turning off the A/C Turning on the Fan and Turning off the A/C September 20, 2010 - 3:00pm Addthis As part of some recent money- and energy-savings improvements I've been making to my home, a couple of weeks ago I installed a ceiling fan in my main living room. Chris Stewart Senior Communicator at DOE's National Renewable Energy Laboratory As part of some recent money- and energy-savings improvements I've been making to my home, a couple of weeks ago I installed a ceiling fan in my main living room. Part of my research led me to understand how ceiling fans are considered the most effective fans compared among table fans, floor fans, and fans mounted to poles or walls because they effectively circulate the air in a room to create a draft throughout the room.

308

Final Report: Fan Filter Unit Project  

NLE Websites -- All DOE Office Websites (Extended Search)

61684 61684 Demonstration of Advanced Filtration Technologies: Developing Energy-rebate Criteria through Performing Standard Laboratory Tests and Statistical Analyses Final Report (LBNL- 61684) To California Energy Commission 2007 Tengfang Xu and Duo Wang 2 Disclaimer This document was prepared as an account of work sponsored by the United States Government and California Energy Commission. While this document is believed to contain correct information, neither the United States Government nor any agency thereof, nor California Energy Commission, nor The Regents of the University of California, nor any of their employees, makes any warranty, express or implied, or assumes any legal responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or

309

Proceedings of second geopressured geothermal energy conference, Austin, Texas, February 23--25, 1976. Volume II. Resource assessment. [Geologic procedures for test- or industrial-site selection along Texas Gulf coast  

DOE Green Energy (OSTI)

This report describes techniques being used in the assessment of geopressured geothermal resources along the Texas Gulf Coast and defines geologic procedures for test- or industrial-site selection. These approaches have been proven in petroleum exploration and are applicable in geothermal exploration here in the Gulf basin and in other sedimentary basins.

Bebout, D.G.

1976-01-01T23:59:59.000Z

310

Savings in electric cooling energy by the use of a whole-house fan. Final report  

Science Conference Proceedings (OSTI)

Hour-by-hour cooling performances of a typical ranch house, with and without the use of a whole-house fan, were compared for the climate conditions throughout the contiguous United States. The comparative analyses were made by the use of NBSWHF, a modified version of NBSLD, to simulate the complex thermal coupling of whole-house-fan ventilated attic space. The calculations were performed for two operational modes: a cyclic fan mode and a stepwise continuous mode.

Kusuda, T.; Bean, J.W.

1981-05-01T23:59:59.000Z

311

Effect of building airtightness and fan size on the performance of mechanical ventilation systems in new U.S. houses: a critique of ASHRAE standard 62.2-2003  

E-Print Network (OSTI)

Determining Air Leakage Rate by Fan Pressurization. Americanof Building Envelopes by the Fan Pressurization Method.Dominated by Strong Exhaust Fan. ASHRAE Transactions. Vol

Roberson, J.

2004-01-01T23:59:59.000Z

312

How Has a Ceiling Fan Affected the Way You Heat and Cool Your Home? |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Has a Ceiling Fan Affected the Way You Heat and Cool Your Home? Has a Ceiling Fan Affected the Way You Heat and Cool Your Home? How Has a Ceiling Fan Affected the Way You Heat and Cool Your Home? September 23, 2010 - 7:30am Addthis On Monday, Chris told you about his new ceiling fan and how it's changed the way he cools his home. In warm weather, ceiling fans cool people (not rooms) by producing a wind-chill effect-which is why you should turn off fans when you leave the room. A ceiling fan allows you to raise the thermostat setting about 4°F with no reduction in comfort. Ceiling fans don't just cool in the summer; you can also reverse the direction in the winter to provide an updraft and force warm air down into the room. How has a ceiling fan affected the way you heat and cool your home? Each Thursday, you have the chance to share your thoughts on a question

313

How Has a Ceiling Fan Affected the Way You Heat and Cool Your Home? |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Has a Ceiling Fan Affected the Way You Heat and Cool Your Home? Has a Ceiling Fan Affected the Way You Heat and Cool Your Home? How Has a Ceiling Fan Affected the Way You Heat and Cool Your Home? September 23, 2010 - 7:30am Addthis On Monday, Chris told you about his new ceiling fan and how it's changed the way he cools his home. In warm weather, ceiling fans cool people (not rooms) by producing a wind-chill effect-which is why you should turn off fans when you leave the room. A ceiling fan allows you to raise the thermostat setting about 4°F with no reduction in comfort. Ceiling fans don't just cool in the summer; you can also reverse the direction in the winter to provide an updraft and force warm air down into the room. How has a ceiling fan affected the way you heat and cool your home? Each Thursday, you have the chance to share your thoughts on a question

314

Parametric System Curves: Correlations Between Fan Pressure Rise and Flow for Large Commercial Buildings  

E-Print Network (OSTI)

distribution, duct design, system curve, fans, leakage iiifan pressure rise and flow measurements over a range of operating conditions. During design,

Sherman, Max

2010-01-01T23:59:59.000Z

315

Toward green systems for cleanrooms: Energy efficient fan-filter units  

E-Print Network (OSTI)

filter unit (FFU), energy efficiency, green system, electricToward Green Systems for Cleanrooms: Energy Efficient Fan-energy efficient models; Market transformation toward “green”

Jeng, Ming-Shan; Xu, Tengfang; Lan, Chao-Ho

2004-01-01T23:59:59.000Z

316

Toward green systems for cleanrooms: Energy efficient fan-filter units  

E-Print Network (OSTI)

Toward Green Systems for Cleanrooms: Energy Efficient Fan-FFU), energy efficiency, green system, electric power use,are challenges and benefits in green designs that integrate

Jeng, Ming-Shan; Xu, Tengfang; Lan, Chao-Ho

2004-01-01T23:59:59.000Z

317

Fallout fans: Negotiations over text integrity in the age of the active audience.  

E-Print Network (OSTI)

??This study investigated how fans and producers of media texts negotiate text integrity, which is defined as an ideal about the validity, wholeness, and truth… (more)

Milner, Ryan M.

2008-01-01T23:59:59.000Z

318

DISCRETE-FREQUENCY AND BROADBAND NOISE RADIATION FROM DIESEL ENGINE COOLING FANS.  

E-Print Network (OSTI)

??This effort focuses on measuring and predicting the discrete-frequency and broadband noise radiated by diesel engine cooling fans. Unsteady forces developed by the interaction of… (more)

Kim, Geon-Seok

2007-01-01T23:59:59.000Z

319

A Real Reflection of How I Write: Young Adult Female Authors Seizing Agency Through Fan Fiction.  

E-Print Network (OSTI)

??This research project examines ""fan fiction"" (stories based upon existing texts such as movies, books, and video games) written by a young adult female and… (more)

Coleman, Susanna

2008-01-01T23:59:59.000Z

320

Failure of a Fan Hub Blade Made of an A713 Al-Zn Alloy  

Science Conference Proceedings (OSTI)

About this Abstract. Meeting, Materials Science & Technology 2012. Symposium, Failure Analysis and Prevention. Presentation Title, Failure of a Fan Hub Blade ...

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Topography based fan control for heavy trucks; Topografibaserad kylfläktstyrning för tunga fordon.  

E-Print Network (OSTI)

?? This thesis is a study of how cooling fan control can be improved by using road topography information. Two such controllers are presented, one… (more)

Lerede, Niclas

2009-01-01T23:59:59.000Z

322

Error Sensor Placement for Active Control of an Axial Cooling Fan.  

E-Print Network (OSTI)

??Recent experimental achievements in active noise control (ANC) for cooling fans have used near-field error sensors whose locations are determined according to a theoretical condition… (more)

Shafer, Benjamin M 1979-

2007-01-01T23:59:59.000Z

323

DUCTED FAN INLET/EXIT AND ROTOR TIP FLOWIMPROVEMENTS FOR VERTICAL LIFT SYSTEMS.  

E-Print Network (OSTI)

??Ducted fan based vertical lift systems are excellent candidates to be in the group of the next generation vertical lift vehicles, with many potential applications… (more)

Akturk, Ali

2010-01-01T23:59:59.000Z

324

FLIGHT CONTROL DESIGN OF TANDEM DUCTED FAN AIRCRAFT USING REDUNDANT CONTROL EFFECTORS.  

E-Print Network (OSTI)

??Controllability and stability of ducted fan air vehicles is a challenging problem due to their complex nonlinear aerodynamics and dynamic behavior. At the same time,… (more)

Ozdemir, Gurbuz

2010-01-01T23:59:59.000Z

325

Investigation of performance improvements including application of inlet guide vanes to a cross-flow fan .  

E-Print Network (OSTI)

??The inherent characteristics of a cross-flow fan allowing for easy thrust vectoring as well as potential airfoil boundary layer control make it an attractive propulsive… (more)

Cordero, Samuel F.

2009-01-01T23:59:59.000Z

326

Perimeter fan performance in forced draught air-cooled steam condensers.  

E-Print Network (OSTI)

??ENGLISH ABSTRACT: Axial flow fan arrays form part of air-cooled steam condensers in direct drycooled power plants. This dissertation investigates the performance of axial flow… (more)

Van der Spuy, Sybrand Johannes

2011-01-01T23:59:59.000Z

327

Arbitrary surface flank milling of fan, compressor, and impeller blades  

SciTech Connect

It is generally conceived that a blade surface is flank millable if it can be closely approximated by a ruled surface; otherwise the slow machining process of point milling has to be employed. However, the authors have now demonstrated that the ruled surface criterion for flank milling is neither necessary nor sufficient. Furthermore, many complex arbitrary surfaces typical of the blades in fans, axial compressors, and centrifugal impellers in aviation gas turbines are actually closely flank millable and can be rendered exactly flank millable with one or more passes per surface often without sacrificing, indeed usually with gain, in performance.

Wu, C.Y. [Pratt and Whitney Canada Incorporated, Longueuil, Quebec, (Canada). Design Engineering

1995-07-01T23:59:59.000Z

328

CHANGES IN SANDSTONE DISTRIBUTIONS BETWEEN THE UPPER, MIDDLE, AND LOWER FAN IN THE ARKANSAS JACKFORK GROUP  

E-Print Network (OSTI)

This study is a statistical analysis of the sandstone distribution within the Arkansas Jackfork Group which is a passive margin fan complex. Passive margin fan systems are typically associated with long fluvial transport, fed by deltas, wide shelf, efficient basin transport, that result in a bypassing system. Passive margin fans are generally fine-grained, mud rich, and well sorted. These fans can be separated into three units (upper, middle, and lower fan) based on their location within the fan and how the sediments are deposited. Five outcrops from the Arkansas Jackfork Group have been chosen for this study and each were divided into different facies dependent on sandstone percentages in certain bed sets. The amount of sandstone for each facies was calculated and a statistical approximation for each outcrop was determined. Sandstone distribution curves were made for each outcrop to show a graphic representation of how the sandstone is dispersed. After analyzing different upper, middle, and lower fan outcrops, it is clear there is an obvious change in the sandstone percentage and distribution. The upper fan deposit has an overall sandstone percentage of approximately 77.5% and is deposited in beds that are mainly amalgamated; 10-30m thick. Sandstone is deposited moderately even and is quite concentrated throughout the exposure. The middle fan outcrops contain approximately 72.6% sandstone and show similar patterns, except that the amalgamated sandstone beds are not as thick, 5-15m and contain more shale in between layers. As expected the lower fan outcrop is completely different in both sandstone percentage and distribution. The lower fan has approximately 65.4% sandstone. The distribution of sandstone is more concentrated in each of the individual units, or systems, but the overall complex has two systems separated by a massive marine shale bed, 33.5 m, that contains virtually no sand.

Mack, Clayton P.

2009-05-01T23:59:59.000Z

329

Model Predictive Control of HVAC Systems: Implementation and Testing at the University of California, Merced  

E-Print Network (OSTI)

fan speed (rpm)      N fan ,0 :    design fan speed (P fan :    fan power (kW)    m cw ,0 :    design water mass 

Haves, Phillip

2010-01-01T23:59:59.000Z

330

Call Forwarding: New NIST Procedure Could Speed Cell ...  

Science Conference Proceedings (OSTI)

Call Forwarding: New NIST Procedure Could Speed Cell Phone Testing. For Immediate Release: March 2, 2010. ...

2010-10-05T23:59:59.000Z

331

Inlet swirl distortion effects on the generation and propagation of fan rotor shock noise  

E-Print Network (OSTI)

A body-force-based fan model for the prediction of multiple-pure-tone noise generation is developed in this thesis. The model eliminates the need for a full-wheel, three-dimensional unsteady RANS simulation of the fan blade ...

Defoe, Jeff (Jeffrey James)

2011-01-01T23:59:59.000Z

332

DOE/EA-1673: Environmental Assessment for Energy Conservation Program for Certain Industrial Equipment: Energy Conservation Standards and Test Procedures for Commercial Heating, Air-Conditioning, and Water-Heating Equipment (July 2009)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 Environmental Assessment for 10 CFR 431 Energy Conservation Program for Certain Industrial Equipment: Energy Conservation Standards and Test Procedures for Commercial Heating, Air- Conditioning, and Water-Heating Equipment July 2009 8-i CHAPTER 8. ENVIRONMENTAL ASSESSMENT TABLE OF CONTENTS 8.1 INTRODUCTION ............................................................................................................... 8-1 8.2 AIR QUALITY ANALYSIS ............................................................................................... 8-1 8.3 AIR POLLUTANT DESCRIPTIONS ................................................................................ 8-1 8.4 AIR QUALITY REGULATIONS ...................................................................................... 8-3

333

Comparison of Test Procedures and Energy Efficiency Criteria in Selected International Standards and Labeling Programs for Clothes Washers, Water Dispensers, Vending Machines and CFLs  

E-Print Network (OSTI)

etc. ) during which energy consumption is measured, the typedoes not specify energy consumption measurements but rather,test in which water and energy consumption are measured. The

Fridley, David

2010-01-01T23:59:59.000Z

334

Performance Analysis of Dual-Fan, Dual-Duct Constant Volume Air-Handling Units  

E-Print Network (OSTI)

Dual-fan, dual-duct air-handling units introduce outside air directly into the cooling duct and use two variable speed devices to independently maintain the static pressure of the hot and the cold air ducts. Analytical models have been developed to compare fan power and thermal energy consumption of dualfan, dual-duct constant volume air-handling units with single-fan, dual-duct constant volume airhandling units. This study shows that the dual-fan, dual-duct system uses less fan power and less thermal energy during winter, and uses more thermal energy during summer. Thermal energy performance can be significantly improved if the thermal energy penalty can be decreased or eliminated.

Joo, I. S.; Liu, M.

2001-01-01T23:59:59.000Z

335

Comparing Two Types of Magnetically- Coupled Adjustable Speed Drives with Variable Frequency Drives in Pump and Fan Applications  

E-Print Network (OSTI)

This paper presents the results from laboratory tests on MagnaDrive Corporations fixed-magnet magnetically-coupled adjustable speed drive (MC-ASD) and Coyote Electronics electromagnetic MC-ASD as compared to a typical variable frequency drive (VFD) for typical fan and pump loads. It also discusses advantages and disadvantages of using mechanical MC-ASD versus VFDs and it provides field experience with VFDs in refrigerated warehouses as well as the fixed magnet MC-ASD in wastewater and other field applications. Laboratory tests for a 50 hp fan retrofit showed electronic VFD savings at 62%, the MagnaDrive Coupling at 39% and PAYBACK Drive at 46%. At $0.06/kWh and list prices, the simple payback for the VFD is 2.4 years, the MagnaDrive is 4.6 years and the PAYBACK is 1.9 years. MagnaDrive has models from 25 to 500 hp while PAYBACK has models from 3 to 200 hp. Contractors to the Northwest Energy Efficiency Alliance have helped to install VFDs for about 300 evaporator fans in over two dozen refrigerated warehouses and to install fixed-magnet MC-ASDs in about 50 applications with about half of these controlling wastewater pumps. The Alliance has no particular field experience with the electcromagnetic coupling. The primary advantages of magnetically coupled adjustable speed drives (MC-ASD) over VFDs come from reduced maintenance, resistance to dirty environments, separation of load vibration from the motor, and less stringent requirements for precise shaft alignment. Field experience indicates reductions in noise and repairs from vibration loads, tolerance of poor electrical power quality, and ease of installation are often more important than energy savings. The MC-ASDs are being used where VFDs have not survived or are considered too complicated.

Anderson, K. J.; Chvala, W. D.

2003-05-01T23:59:59.000Z

336

A passive margin-type submarine fan complex, Permian Ecca Group, South Africa  

Science Conference Proceedings (OSTI)

A submarine fan complex, comprising five arenaceous fan systems separated by basinal shale units, occurs in the southwestern part of the intracratonic Karoo basin in South Africa. Although basin development is related to a subduction zone bordering the palaeo-Pacific ocean to the south of Gondwanaland and the evolution of the Cape Fold Belt, the entire Lower Permian Ecca Group basin-fill succession reflects depositional characteristics of a passive-margin setting. The submarine fan complex, 250 m thick, originated from sediments supplied by Mississippi-type deltas dominating the Ecca coastline. The fine grain-size and low sand/shale ratio of the submarine fan and deltaic deposits reflect the maturity of the ancient river systems. Outcrops of the fan complex are well exposed and cover an area of 650 km{sup 2}. The strata are not affected by folding, and deep erosion allows three-dimensional viewing of mid-fan to outer-fan deposits. Features of interest include stacked lobe deposits displayed along 2.5 km of a 60 m high cliff section, and a transverse cliff section through channel-fill deposits 500 m wide. Paleocurrent directions reveal that each sequence had its own main source area located to the northwest and south of its present geographic location. The cyclic nature of the fan complex is attributed to relative sea-level changes; deposition took place on the basin floor in water depths that do not exceed 500 m. Shoaling of the basin to wave base depths is reflected in the pro-delta and delta front deposits overlying the uppermost fan sequence. Major factors in controlling direction of fan progradation were delta switching and basin floor topography.

Wickens, H.D. (SOEKOR-Pty. Ltd., Parow (South Africa)); Bouma, A.H. (Louisiana State Univ., Baton Rouge (United States))

1991-03-01T23:59:59.000Z

337

Acceptance Test Procedure for Project 251W, WBS 3, Substation A-8, Building 251-W, Bus {number_sign}2 switchgear replacement  

Science Conference Proceedings (OSTI)

This document records the steps taken and results of the acceptance testing of the new 13.8kV switchgear installed at 251W. This gear is under the administrative control of Electrical Utilities.

VanBaalen, R.A.

1995-02-01T23:59:59.000Z

338

Microsoft Word - Control_and_Fan_Improvements_in_CRAHs.doc  

NLE Websites -- All DOE Office Websites (Extended Search)

07E 07E Demonstration of Intelligent Control and Fan Improvements in Computer Room Air Handlers Henry Coles and Steve Greenberg, Lawrence Berkeley National Laboratory Corinne Vita, Vigilent Environmental Energy Technologies Division November 2012 DISCLAIMER This document was prepared as an account of work sponsored by the United States Government. While this document is believed to contain correct information, neither the United States Government nor any agency thereof, nor The Regents of the University of California, nor any of their employees, makes any warranty, express or implied, or assumes any legal responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe

339

Fan-shaped and toric textures of mesomorphic oxadiazoles  

E-Print Network (OSTI)

When a family of non symmetrical heterocycled compounds is investigated, a variety of mesophases can be observed with rather different features. Here we report the behaviour of seven different members among a family of such materials, that consists of mesomorphic oxadiazole compounds. In two of these compounds, the optical microscope investigation shows very interesting behaviours. In their smectic phases, fan-shaped and toric textures, sometimes with periodic instability, are observed. Moreover, the nematic phase displays a texture transition. Texture transitions have been previously observed only inside the nematic phase of some compounds belonging to the families of the oxybenzoic and cyclohexane acids. In these two oxadiazole compounds we can observe what we define as a "toric nematic phase", heating the samples from the smectic phase. The toric nematic texture disappears as the sample is further heated, changing into a smooth texture.

A. Sparavigna; A. Mello; B. Montrucchio

2007-04-11T23:59:59.000Z

340

A Comparison of US and Chinese EV Battery Testing Protocols  

NLE Websites -- All DOE Office Websites (Extended Search)

EV Battery Testing Protocols: Results D. Robertson, 1 J. Christophersen, 2 Fang Wang, 3 Fan Bin, 3 I. Bloom 1 USChina Electric Vehicle Initiative Meeting August 23-24, 2012...

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Nondestructive Evaluation: Plant-Specific Applications of Qualified Nozzle Inner Radius and Nozzle-to-Shell Weld Ultrasonic Testing Procedures Using EPRI Computer Models -- 2002-2010  

Science Conference Proceedings (OSTI)

This report is the fourth in a series of periodic technical updates documenting plant-specific applications of qualified nozzle inner radius and nozzle-to-shell weld ultrasonic testing techniques developed using the Electric Power Research Institute Nondestructive Evaluation programs three-dimensional nozzle models. This particular update covers the period 20022010.

2010-11-16T23:59:59.000Z

342

Slimhole Handbook- Procedures And Recommendations For Slimhole...  

Open Energy Info (EERE)

Slimhole Handbook- Procedures And Recommendations For Slimhole Drilling And Testing In Geothermal Exploration Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Report:...

343

Additional Guidance Regarding Application of Current Procedures...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of Clothes Washers with Warm Rinse Cycles, Issued: June 30, 2010 Additional Guidance...

344

TEST  

Science Conference Proceedings (OSTI)

This is an abstract. TEST Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras lacinia dui et est venenatis lacinia. Vestibulum lacus dolor, adipiscing id mattis sit amet, ultricies sed purus. Nulla consectetur aliquet feugiat. Maecenas ips

345

Economic Recovery of Oil Trapped at Fan Margins Using High Angle Wells Multiple Hydraulic Fractures  

SciTech Connect

This project attempts to demonstrate the effectiveness of exploiting thin-layered, low-energy deposits at the distal margin of a prograding turbidite complex through the use of hydraulically fractured horizontal or high-angle wells. The combination of a horizontal or high-angle well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. A high-angle well will be drilled in the fan-margin portion of a slope-basin clastic reservoir and will be completed with multiple hydraulic-fracture treatments. Geologic modeling, reservoir characterization, and fine-grid reservoir simulation will be used to select the well location and orientation. Design parameters for the hydraulic-fracture treatments will be determined, in part, by fracturing an existing test well. Fracture azimuth will be predicted by passive seismic monitoring of a fracture-stimulation treatment in the test well using logging tools in an offset well.

Mike L. Laue

1997-10-30T23:59:59.000Z

346

ECONOMIC RECOVERY OF OIL TRAPPED AT FAN MARGINS USING HIGH ANGLE WELLS AND MULTIPLE HYDRAULIC FRACTURES  

Science Conference Proceedings (OSTI)

This project attempts to demonstrate the effectiveness of exploiting thin-layered, low-energy deposits at the distal margin of a prograding turbidite complex through the use of hydraulically fractured horizontal or high-angle wells. The combination of a horizontal or high-angle well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. A high-angle well will be drilled in the fan-margin portion of a slope-basin clastic reservoir and will be completed with multiple hydraulic-fracture treatments. Geologic modeling, reservoir characterization, and fine-grid reservoir simulation will be used to select the well location and orientation. Design parameters for the hydraulic-fracture treatments will be determined, in part, by fracturing an existing test well. Fracture azimuth will be predicted by passive seismic monitoring of a fracture-stimulation treatment in the test well using logging tools in an offset well.

Mike L. Laue

1998-11-06T23:59:59.000Z

347

Methodology to Develop and Test an Easy-to-use Procedure for the Preliminary Selection of High-performance Systems for Office Buildings in Hot and Humid Climates  

E-Print Network (OSTI)

A procedure has been developed for the preliminary selection of high-performance systems for office buildings in hot and humid climates. High-performance building systems and components were surveyed for buildings in the U.S., which were applicable for office buildings in hot and humid climates. This research developed a calibrated DOE-2.1e simulation model of a prototypical large office building. In addition, a Simplified Geometry DOE-2.1e (SGDOE-2.1e) model, was also developed, which used a simplified geometry to demonstrate the use of a proposed easy-to-use tool. The calibrated DOE-2.1e simulation model and the SGDOE-2.1e were compared and showed a good match with each. The SGDOE-2.1e model was then further modified based on the ASHRAE Standard 90.1-1999 commercial building energy code. A code-compliant (ASHRAE Standard 90.1-1999) SGDOE-2.1e simulation model was then used as a baseline for the evaluation of the high-performance measures. A total of 14 high-performance measures were implemented including the energy savings, while the comfort level was maintained based on the ASHRAE comfort zone. In addition to the 14 high-performance measures, solar thermal and solar PV system analysis were integrated with the SGDOE-2.1e simulation model to further reduce the annual energy use. Finally, specifications of the proposed easy-to-use simulation tool were developed. This tool includes options to choose systems from the 14 high-performance measures and solar systems. The proposed easy-to-use systems selection tool can be used for new building practitioners and existing building owners as well to evaluate the performance of their new buildings compared to the ASHRAE Standard 90.1-1999 code-compliant building, and to assess the feasibility of implementing high-performance measures to their existing buildings in terms of energy and cost savings.

Cho, Sool Yeon

2009-08-01T23:59:59.000Z

348

Methodology to Develop and Test an Easy-To-Use Procedure for the Preliminary Selection of High-Performance Systems for Office Buildings in Hot and Humid Climates  

E-Print Network (OSTI)

A procedure has been developed for the preliminary selection of high-performance systems for office buildings in hot and humid climates. High-performance building systems and components were surveyed for buildings in the U.S., which were applicable for office buildings in hot and humid climates. This research developed a calibrated DOE-2.1e simulation model of a prototypical large office building. In addition, a Simplified Geometry DOE-2.1e (SGDOE-2.1e) model, was also developed, which used a simplified geometry to demonstrate the use of a proposed easy-to-use tool. The calibrated DOE-2.1e simulation model and the SGDOE-2.1e were compared and showed a good match with each. The SGDOE-2.1e model was then further modified based on the ASHRAE Standard 90.1-1999 commercial building energy code. A code-compliant (ASHRAE Standard 90.1-1999) SGDOE-2.1e simulation model was then used as a baseline for the evaluation of the high-performance measures. A total of 14 high-performance measures iv were implemented including the energy savings, while the comfort level was maintained based on the ASHRAE comfort zone. In addition to the 14 high-performance measures, solar thermal and solar PV system analysis were integrated with the SGDOE-2.1e simulation model to further reduce the annual energy use. Finally, specifications of the proposed easy-to-use simulation tool were developed. This tool includes options to choose systems from the 14 high-performance measures and solar systems. The proposed easy-to-use systems selection tool can be used for new building practitioners and existing building owners as well to evaluate the performance of their new buildings compared to the ASHRAE Standard 90.1-1999 code-compliant building, and to assess the feasibility of implementing high-performance measures to their existing buildings in terms of energy and cost savings.

Cho, S.

2009-08-01T23:59:59.000Z

349

Property:Building/SPBreakdownOfElctrcityUseKwhM2Fans | Open Energy  

Open Energy Info (EERE)

Fans Fans Jump to: navigation, search This is a property of type String. Fans Pages using the property "Building/SPBreakdownOfElctrcityUseKwhM2Fans" Showing 25 pages using this property. (previous 25) (next 25) S Sweden Building 05K0001 + 5.21311928139 + Sweden Building 05K0002 + 18.5995610535 + Sweden Building 05K0003 + 20.3514016294 + Sweden Building 05K0004 + 8.08671679198 + Sweden Building 05K0005 + 16.0166245259 + Sweden Building 05K0006 + 10.358795651 + Sweden Building 05K0007 + 8.3953561818 + Sweden Building 05K0008 + 9.28527472527 + Sweden Building 05K0009 + 12.8398873749 + Sweden Building 05K0010 + 20.0966982674 + Sweden Building 05K0011 + 6.90408963585 + Sweden Building 05K0012 + 8.60719192175 + Sweden Building 05K0013 + 16.7539365907 +

350

Property:Building/SPBreakdownOfElctrcityUseKwhM2CirculationFans | Open  

Open Energy Info (EERE)

CirculationFans CirculationFans Jump to: navigation, search This is a property of type String. Circulation fans Pages using the property "Building/SPBreakdownOfElctrcityUseKwhM2CirculationFans" Showing 25 pages using this property. (previous 25) (next 25) S Sweden Building 05K0001 + 13.3422495258 + Sweden Building 05K0002 + 0.0 + Sweden Building 05K0003 + 2.80646609789 + Sweden Building 05K0004 + 8.95823904901 + Sweden Building 05K0005 + 5.55016340076 + Sweden Building 05K0006 + 6.81308969891 + Sweden Building 05K0007 + 2.02541916787 + Sweden Building 05K0008 + 0.625641025641 + Sweden Building 05K0009 + 7.59721281624 + Sweden Building 05K0010 + 0.0 + Sweden Building 05K0011 + 0.757191316527 + Sweden Building 05K0012 + 6.04077487892 + Sweden Building 05K0013 + 0.767224182906 +

351

Quiet Computing with BSD: Fan control with sysctl hw.sensors.  

E-Print Network (OSTI)

We will discuss the topic of fan control and introduce sysctl-based interfacing with the fancontrolling capabilities of microprocessor system hardware monitors on OpenBSD. The discussed prototype implementation reduces the noise and power-consumption characteristics in fans of personal computers, especially of those PCs that are designed from off-the-shelf components. We further argue that our prototype is easier, robuster and more intuitive to use compared to solutions available elsewhere. 1.

Constantine A. Murenin; Raouf Boutaba

2010-01-01T23:59:59.000Z

352

Root-Cause Failure Analysis: Fossil-Fired Power Plant Draft Fans  

Science Conference Proceedings (OSTI)

This report describes the collection and analysis of fan-related outage data for 61 large fossil fuel steam power plants. The outage causes are ranked in terms of their impact on production, and a systematic search for generic root causes is described. Recommendations are made for short-term corrective measures and for longer-term research efforts to significantly improve fan system reliability.

1983-07-01T23:59:59.000Z

353

Application of Adjustable Speed Drives to Induced Draft Fans at NSP-SHERCO Power Plant  

Science Conference Proceedings (OSTI)

Induced draft (ID) fans on power boilers control the flow of flue gasses from the boiler to the atmosphere-and their smooth operation is essential to the efficient operation of any generating station. Adjustable speed drive (ASD) control of an electric motor ID fan can provide significant energy savings while increasing the accuracy and precision of boiler draft and fuel gas flow regulation. This study quantified the energy savings and identified other benefits of applying ASDs to four existing electric-...

1999-10-19T23:59:59.000Z

354

Generation of fan-states of radiation field in a cavity  

E-Print Network (OSTI)

A scheme of generating recently introduced fan-states | \\alpha, 2k>_F (\\alpha is complex, k=1,2,3,...) is proposed basing on a \\Lambda-type atom-cavity field interaction. We show that with suitable atomic preparations and measurements a passage of a sequence of N atoms through a cavity may transform an initial field coherent state | \\alpha> to a fan-state | \\alpha, 2k>_F with k=2^{N-2}.

Nguyen Ba An; Truong Minh Duc

2001-11-30T23:59:59.000Z

355

Engine having hydraulic and fan drive systems using a single high pressure pump  

DOE Patents (OSTI)

An engine comprises a hydraulic system attached to an engine housing that includes a high pressure pump and a hydraulic fluid flowing through at least one passageway. A fan drive system is also attached to the engine housing and includes a hydraulic motor and a fan which can move air over the engine. The hydraulic motor includes an inlet fluidly connected to the at least one passageway.

Bartley, Bradley E. (Manito, IL); Blass, James R. (Bloomington, IL); Gibson, Dennis H. (Chillicothe, IL)

2000-01-01T23:59:59.000Z

356

Parametric System Curves: Correlations Between Fan Pressure Rise and Flow for Large Commercial Buildings  

SciTech Connect

A substantial fraction of HVAC energy use in large commercial buildings is due to fan operation. Fan energy use depends in part on the relationship between system pressure drop and flow through the fan, which is commonly called a "system curve." As a step toward enabling better selections of air-handling system components and analyses of common energy efficiency measures such as duct static pressure reset and duct leakage sealing, this paper shows that a simple four-parameter physical model can be used to define system curves. Our model depends on the square of the fan flow, as is commonly considered. It also includes terms that account for linear-like flow resistances such as filters and coils, and for supply duct leakage when damper positions are fixed or are changed independently of static pressure or fan flow. Only two parameters are needed for systems with variable-position supply dampers (e.g., VAV box dampers modulating to control flow). For these systems, reducing or eliminating supply duct leakage does not change the system curve. The parametric system curve may be most useful when applied to field data. Non-linear techniques could be used to fit the curve to fan pressure rise and flow measurements over a range of operating conditions. During design, when measurements are unavailable, one could use duct design calculation tools instead to determine the coefficients.

Sherman, Max; Wray, Craig

2010-05-19T23:59:59.000Z

357

Applicability of fan spray nozzles to stripping insoluble gases from viscous liquids  

SciTech Connect

Fan spray nozzle stripping appears to be a practical technique for separating dilute volatile solutes from nonvolatile solvents. In particular this technique can be used to strip molecular tritium and tritium fluoride at extremely small concentration (in the parts per million range) from molten salts used as blanket materials in a fusion reactor. Under adjusted operating conditions of the fan spray as it leaves the nozzle, a high percentage of the theoretically maximum achievable stripping would take place from the expanding sheet of the fan spray as it leaves the nozzle and before it breaks up. Although the only available experimental data are for aqueous solutions, a new theoretical analysis of the fan spray sheet demonstrates the applicability of this technique to nonaqueous liquids. The equation derived from this analysis relates the theoretically achievable mass transfer efficiency to the properties of the liquid flowing through the fan spray nozzle and to the operating conditions of the nozzle. Any fluid with viscosity higher than or equal to that of water would be expected to follow this equation as long as a fan-shaped sheet is formed under the operating conditions of the nozzle.

Tseng, H.H.; Johnson, E.F.

1983-08-01T23:59:59.000Z

358

The noise power spectrum in CT with direct fan beam reconstruction  

Science Conference Proceedings (OSTI)

The noise power spectrum (NPS) is a useful metric for understanding the noise content in images. To examine some unique properties of the NPS of fan beam CT, the authors derived an analytical expression for the NPS of fan beam CT and validated it with computer simulations. The nonstationary noise behavior of fan beam CT was examined by analyzing local regions and the entire field-of-view (FOV). This was performed for cases with uniform as well as nonuniform noise across the detector cells and across views. The simulated NPS from the entire FOV and local regions showed good agreement with the analytically derived NPS. The analysis shows that whereas the NPS of a large FOV in parallel beam CT (using a ramp filter) is proportional to frequency, the NPS with direct fan beam FBP reconstruction shows a high frequency roll off. Even in small regions, the fan beam NPS can show a sharp transition (discontinuity) at high frequencies. These effects are due to the variable magnification and therefore are more pronounced as the fan angle increases. For cases with nonuniform noise, the NPS can show the directional dependence and additional effects.

Baek, Jongduk; Pelc, Norbert J. [Department of Radiology, Stanford University, Stanford, California 94305 (United States); Department of Radiology, Stanford University, Stanford, California 94305 (United States); Department of Electrical Engineering, Stanford University, Stanford, California 94305 (United States) and Department of Bioengineering, Stanford University, Stanford, California 94305 (United States)

2010-05-15T23:59:59.000Z

359

Channel complex architecture of fine-grained submarine fans at the base-of-slope  

Science Conference Proceedings (OSTI)

The fan-valley or upper fan channel connects the submarine canyon on the outer shelf-upper slope to the basin proper. It is an erosionally-formed channel that is a conduit for sediment transported to the basin. The valley may widen where it enters the base-of-slope area. Most of the density flows are much smaller than the initial flow and therefore will not occupy the entire width of the upper fan channel. Smaller individual channels will be constructed resulting in a massive fill comprised of amalgamated sandstones. Sand-rich levees and overbank deposits flank each channel. Channel switching may take place toward locations with a slightly steeper gradient. These switches most likely result from irregular flow successions and different flow sizes. Erosion between successive channels is common, removing part of the channel fill and levee-overbank deposits. This results in a disorderly distribution of low-permeability barriers creating local obstruction to connectivity. A study of the sedimentological architecture of the updip mid-fan channel complex was conducted on cliff sections of the Permian Tanqua Karoo subbasin in South Africa, and in Big Rock Quarry in North Little Rock, Arkansas. Seismic records of the base-of-slope of the Mississippi Fan show a widening pattern, and of the Bryant Canyon Fan Complex south of the Sigsbee Escarpment the channel complexity. Integration of seismic data in outcrop observations improves our understanding of the complexity of many good reservoir sands, typically overlain by slope shales.

Bouma, A.H. [Louisiana State Univ., Baton Rouge, LA (United States); Gwang, H. [Kunsan National Univ. (Korea, Democratic People`s Republic of); Van Antwerepen, O. [Univ. of Port Elizabeth (South Africa)] [and others

1995-10-01T23:59:59.000Z

360

Limit processes for TASEP with shocks and rarefaction fans  

E-Print Network (OSTI)

We consider the totally asymmetric simple exclusion process (TASEP) with two-sided Bernoulli initial condition, i.e., with left density rho_- and right density rho_+. We consider the associated height function, whose discrete gradient is given by the particle occurrences. Macroscopically one has a deterministic limit shape with a shock or a rarefaction fan depending on the values of rho_{+/-}. We characterize the large time scaling limit of the fluctuations as a function of the densities rho_{+/-} and of the different macroscopic regions. Moreover, using a slow decorrelation phenomena, the results are extended from fixed time to the whole space-time, except along the some directions (the characteristic solutions of the related Burgers equation) where the problem is still open. On the way to proving the results for TASEP, we obtain the limit processes for the fluctuations in a class of corner growth processes with external sources, of equivalently for the last passage time in a directed percolation model with two-sided boundary conditions. Additionally, we provide analogous results for eigenvalues of perturbed complex Wishart (sample covariance) matrices.

Ivan Corwin; Patrik L. Ferrari; Sandrine Péché

2010-02-18T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Characteristics of some submarine fan channels, Permian Ecca Group, South Africa  

Science Conference Proceedings (OSTI)

The vary well exposed submarine fan complex in the southwestern part of the Karoo basin permits close examination of channel-fills and in places their associated overbank deposits. The complex comprises five arenaceous fan systems some of which attain 60 m in thickness. The fans are vertically stacked and separated by basinal shale deposits; each system with its own direction of growth. The association of channelized sandstone bodies and thin-bedded sandstone and shale packages in an updip position from predominantly stacked lobe deposits suggest preservation of middle fan settings. A 500 m wide, 20 m thick channel-fill consisting massive amalgamated sandstone beds occupying the channel thalweg occurs in a setting dominated by thin-bedded, ripple-laminated sandstone and shale. Gradual thinning of the channel-fill beds toward the channel edges, lack of internal lateral accretion, and a high width to depth ratio suggests a low sinuous to straight channel. The channel-fill is capped by an abandonment facies characterized by ripple-laminated sandstone and shale. Stacked, laterally offset channel-fill deposits with highly erosional contacts and typical well-bedded overbank deposits form channel-overbank complexes and characterize the mid-fan region of the uppermost fan system. Palaeocurrent directions and gradual diminishing of bed-thickness away from the generally massively bedded, amalgamated channel-fill sandstones confirm a simultaneous channel/overbank origin for these deposits. Levee morphology has not been recognized. Both examples of channel-fills cited reveal part of the complexity of the channelized portions of submarine fans and hence the implications thereof in exploring for hydrocarbon reservoirs.

Bouma, A.H. (Louisiana State Univ., Baton Rouge (United States)); Dev Wickens, H. (Soekor, Parow (South Africa))

1991-03-01T23:59:59.000Z

362

Computerized procedures system  

DOE Patents (OSTI)

An online data driven computerized procedures system that guides an operator through a complex process facility's operating procedures. The system monitors plant data, processes the data and then, based upon this processing, presents the status of the current procedure step and/or substep to the operator. The system supports multiple users and a single procedure definition supports several interface formats that can be tailored to the individual user. Layered security controls access privileges and revisions are version controlled. The procedures run on a server that is platform independent of the user workstations that the server interfaces with and the user interface supports diverse procedural views.

Lipner, Melvin H. (Monroeville, PA); Mundy, Roger A. (North Huntingdon, PA); Franusich, Michael D. (Upper St. Clair, PA)

2010-10-12T23:59:59.000Z

363

Field Study of Exhaust Fans for Mitigating Indoor Air Quality Problems: Final Report to Bonneville Power Administration  

E-Print Network (OSTI)

Fans Air-to-Air Heat Exchangers. . . . . . . . . . . . . . .expected from heat exchangers Ventilation expected fromventilation supplied by heat exchanger and exhaust flow. .

Grimsrud, David T.

2009-01-01T23:59:59.000Z

364

LETTER REPORT INDEPENDENT VERIFICATION OF THE HIGH FLUX BEAM REACTOR DECOMMISSIONING PROJECT FAN HOUSE, BUILDING 704 BNL  

Science Conference Proceedings (OSTI)

5098-LR-01-0 -LETTER REPORT INDEPENDENT VERIFICATION OF THE HIGH FLUX BEAM REACTOR DECOMMISSIONING PROJECT FAN HOUSE, BUILDING 704 BROOKHAVEN NATIONAL LABORATORY

P.C. Weaver

2010-10-22T23:59:59.000Z

365

Caratterizzazione del rumore generato dal fan di motori aeronautici e Metodo inverso per la ricostruzione della sorgente.  

E-Print Network (OSTI)

??Il seguente lavoro tratta una procedura per la ricostruzione della sorgente acustica del fan di un motore turbofan per uso aeronautico mediante metodo inverso. Tale… (more)

BIANCHI, FRANCESCO

2009-01-01T23:59:59.000Z

366

Human factoring administrative procedures  

Science Conference Proceedings (OSTI)

In nonnuclear business, administrative procedures bring to mind such mundane topics as filing correspondence and scheduling vacation time. In the nuclear industry, on the other hand, administrative procedures play a vital role in assuring the safe operation of a facility. For some time now, industry focus has been on improving technical procedures. Significant efforts are under way to produce technical procedure requires that a validated technical, regulatory, and administrative basis be developed and that the technical process be established for each procedure. Producing usable technical procedures requires that procedure presentation be engineered to the same human factors principles used in control room design. The vital safety role of administrative procedures requires that they be just as sound, just a rigorously formulated, and documented as technical procedures. Procedure programs at the Tennessee Valley Authority and at Boston Edison's Pilgrim Station demonstrate that human factors engineering techniques can be applied effectively to technical procedures. With a few modifications, those same techniques can be used to produce more effective administrative procedures. Efforts are under way at the US Department of Energy Nuclear Weapons Complex and at some utilities (Boston Edison, for instance) to apply human factors engineering to administrative procedures: The techniques being adapted include the following.

Grider, D.A.; Sturdivant, M.H.

1991-11-01T23:59:59.000Z

367

Federal Agency NEPA Procedures  

Energy.gov (U.S. Department of Energy (DOE))

Each Federal agency is required to develop NEPA procedures that supplement the CEQ Regulations. Developed in consultation with CEQ, Federal agency NEPA procedures must meet the standards in the CEQ...

368

TECMIPT Test Operations Procedures (TTOP) For Passive ...  

Science Conference Proceedings (OSTI)

... Conducted disturbances induced by bursts and radio ... on the ingress protection rating (IP) requirement as ... of the initial mean gamma-ray or neutron ...

2013-01-10T23:59:59.000Z

369

ebXML Test Procedures DRAFT Document  

Science Conference Proceedings (OSTI)

... An attack is a specific application of an exploit [After AP-Glossary]. ... Page 7. NIST SP 500-269 January 2008 Page 7 of 13 1.5 Glossary of Terms ...

2013-05-07T23:59:59.000Z

370

Building Technologies Office: Current Test Procedure Waivers  

NLE Websites -- All DOE Office Websites (Extended Search)

2805 72FR71387 121707 Air Conditioners and Heat Pumps, Residential Multi-zone Unitary Small Air Conditioners and Heat Pumps ECR International, Inc. 78FR47681 080613 Heat Pump...

371

Stay Cool for Less Money with a Ceiling Fan | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Stay Cool for Less Money with a Ceiling Fan Stay Cool for Less Money with a Ceiling Fan Stay Cool for Less Money with a Ceiling Fan May 12, 2009 - 5:00am Addthis Allison Casey Senior Communicator, NREL After a few late snowstorms here in Colorado, I am more than ready to turn off the heat and enjoy some warm spring weather. We haven't had any heat waves here yet, but many of you have already been trying to stay cool; our friends in Washington, D.C. were sweltering (by comparison) in 90+°F weather just a couple short weeks ago! Whether you're still anticipating snow or have broken out the sandals and tank tops, you may be starting to think about keeping your summer cooling costs down. One easy way to keep cool while saving money is using a ceiling fan. Did you know that a ceiling fan could allow you to raise the thermostat

372

EM Policies and Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Environmental Management (EM) Desktop References This page offers Environmental Management (EM) operating policies, procedures, standards, workaids, organizational charts, and...

373

ECONOMIC RECOVERY OF OIL TRAPPED AT FAN MARGINS USING HIGH ANGLE WELLS AND MULTIPLE HYDRAULIC FRACTURES  

Science Conference Proceedings (OSTI)

This project attempts to demonstrate the effectiveness of exploiting thin-layered, low-energy deposits at the distal margin of a prograding turbidite complex through the use of hydraulically fractured horizontal or high-angle wells. The combination of a horizontal or high-angle well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. A high-angle well will be drilled in the fan-margin portion of a slope-basin clastic reservoir and will be completed with multiple hydraulic-fracture treatments. Geologic modeling, reservoir characterization, and fine-grid reservoir simulation will be used to select the well location and orientation. Design parameters for the hydraulic-fracture treatments will be determined, in part, by fracturing an existing test well. Fracture azimuth will be predicted by passive seismic monitoring of a fracture-stimulation treatment in the test well using logging tools in an offset well. The long radius, near horizontal well was drilled during the first quarter of 1996. Well conditions resulted in the 7 in. production liner sticking approximately 900 ft off bottom. Therefore, a 5 in. production liner was necessary to case this portion of the target formation. Swept-out sand intervals and a poor cement bond behind the 5 in. liner precluded two of the three originally planned hydraulic fracture treatments. As a result, all pay intervals behind the 5 in. liner were perforated and stimulated with a non-acid reactive fluid. Following a short production period, the remaining pay intervals in the well (behind the 7 in. liner) were perforated. The well was returned to production to observe production trends and pressure behavior and assess the need to stimulate the new perforations.

Mike L. Laue

2001-09-28T23:59:59.000Z

374

PCS Nitrogen: Combustion Fan System Optimization Improves Performance and Saves Energy at a Chemical Plant  

Science Conference Proceedings (OSTI)

This U.S. Department of Energy Industrial Technologies Program case study describes how, in 2003, PCS Nitrogen, Inc., improved the efficiency of the combustion fan on a boiler at the company's chemical fertilizer plant in Augusta, Georgia. The project saved $420,000 and 76,400 million British thermal units (MBtu) per year. In addition, maintenance needs declined, because there is now less stress on the fan motor and bearings and less boiler feed water usage. This project was so successful that the company has implemented more efficiency improvements that should result in energy cost savings of nearly $1 million per year.

Not Available

2005-01-01T23:59:59.000Z

375

Predicting of fan speed for energy saving in HVAC system based on adaptive network based fuzzy inference system  

Science Conference Proceedings (OSTI)

In this paper, a HVAC (heating, ventilating and air-conditioning) system has two different zones was designed and fan motor speed to minimize energy consumption of the HVAC system was controlled by a conventional (proportional-integral-derivative) PID ... Keywords: ANFIS, Air flow control, Energy saving, Fan motor speed predicting, HVAC system, PID control, Temperature control

Servet Soyguder; Hasan Alli

2009-05-01T23:59:59.000Z

376

Study of the effects of ambient conditions upon the performance of fan powdered, infrared, natural gas burners. Quarterly technical progress report, January 1, 1996--March 31, 1996  

DOE Green Energy (OSTI)

The objective of this investigation is to characterize the operation of fan powered infrared burner (PER) at various gas compositions and ambient conditions and develop design guidelines for appliances containing PER burners for satisfactory performance. During this past quarter, a porous radiant burner testing facility consisting of a commercial deep-fat fryer, an FTIR based spectral radiance measurement system, a set of flue gas analysis components, and a fuel gas mixing station was constructed. The measurement capabilities of the system were tested using methane and the test results were found to be consistent with the literature. Various gas mixtures were tested. Results indicated that the stability limits of the burner and emissions vary with fuel gas composition and air/fuel ratio. However, the maximum radiant efficiency of the burner remained constant. Results obtained from this study can be useful to develop optimum design guidelines for PER burner manufacturers.

Bai, T.; Yeboah, Y.D.; Sampath, R.

1996-04-01T23:59:59.000Z

377

Automated Aspect Recommendation through Clustering-Based Fan-in Analysis  

Science Conference Proceedings (OSTI)

Identifying code implementing a crosscutting concern (CCC) automatically can benefit the maintainability and evolvability of the application. Although many approaches have been proposed to identify potential aspects, a lot of manual work is typically ... Keywords: ranking metric, automated aspect recommendation, clustering-based fan-in analysis, crosscutting concern, refactorable aspects, aspect mining, method clusters, lexical based clustering

Danfeng Zhang; Yao Guo; Xiangqun Chen

2008-09-01T23:59:59.000Z

378

Imbalance of CPU temperatures in a blade system and its impact for power consumption of fans  

Science Conference Proceedings (OSTI)

We are now developing a new metric of data center power efficiency to fairly evaluate the contribution of each improvement for power efficiency. In order to develop it, we built a testbed of a data center and measured power consumption of each components ... Keywords: CPU temperature, Data center, Fan speed, Power consumption, Power efficiency

Yuetsu Kodama; Satoshi Itoh; Toshiyuki Shimizu; Satoshi Sekiguchi; Hiroshi Nakamura; Naohiko Mori

2013-03-01T23:59:59.000Z

379

Evaluation of ASD Systems for Electric Arc Furnace and Argon Oxygen Decarburization Refiner Baghouse Fans  

Science Conference Proceedings (OSTI)

An adjustable speed drive (ASD) offers opportunities to operate dust collection fans in a more energy efficient manner. This report focuses on the system requirements and provides a method for successfully applying ASDs to dust extraction baghouse systems in a steel melting and refining application in order to realize full energy savings and operational improvements.

1998-01-23T23:59:59.000Z

380

Engineering Task Plan for Hepa Filter Differential Pressure (DP) Fan Interlock Upgrades  

SciTech Connect

This document provides a plan for installation of Differential Pressure (DP) fan interlocks on the primary ventilation systems in selected Tank Farm facilities. This plan contains the engineering tasks required for installation and is summarized by the Acceptance for Beneficial Use list. Individuals responsible for each task are identified and scheduled accordingly.

SIMONS, S.R.

2000-05-19T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Fan to parallel beam conversion in CAT by rubber sheet transformation  

SciTech Connect

A technique for converting fan-beam projections to parallel-beam projections for use in computed tomography is presented. The problem is approached by use of a rubber sheet transformation. Since the data is discretized, an interpolation step is necessary. For densely sampled data this approach appears satisfactory and a significant reduction in photon noise is observable in computer simulations.

Wecksung, G.W.; Kruger, R.P.; Morris, R.A.

1979-01-01T23:59:59.000Z

382

Retlif Testing Laboratories  

Science Conference Proceedings (OSTI)

... of radio disturbance characteristics of electrical motor-operated and ... and Test Procedures for Airborne Equipment - Section 15 - Magnetic Effect. ...

2014-01-03T23:59:59.000Z

383

University of Waste Procedures  

E-Print Network (OSTI)

University of Maryland Hazardous And Regulated Waste Procedures Manual Revised July 2001 #12;Review II. HAZARDOUS WASTE MANAGEMENT III. BIOLOGICAL, PATHOLOGICAL AND MEDICAL WASTE (BPMW) MANAGEMENT IV. LOW-LEVEL RADIOACTIVE WASTE (LLRW) MANAGEMENT V. EMERGENCY PROCEDURES VI. WASTE MINIMIZATION VII

Rubloff, Gary W.

384

Development of a Fan-Filter Unit Test Standard, Laboratory Validations, and its Applications across Industries  

E-Print Network (OSTI)

and Renewable Energy, Office of Building Technology, State, andand Renewable Energy, Office of Building Technology, State, and

Xu, Tengfang

2008-01-01T23:59:59.000Z

385

Advanced Energy-Efficient Filtration: Fan Filter Unit  

E-Print Network (OSTI)

8 5.3.1 FFU Electric Power and Airflowacross the unit. Total electric power demand. 5.2.1 Test5.3 Results 5.3.1 FFU Electric Power and Airflow Speed

Xu, Tengfang

2005-01-01T23:59:59.000Z

386

NFRC Procedures for Laminates  

NLE Websites -- All DOE Office Websites (Extended Search)

Laminates Laminates Last update: 12/10/2013 07:29 PM NFRC now has a procedure for making laminates in Optics5 and importing those laminate constructions into WINDOW5 to be used in a whole product calculation. The information presented below is provided to help simulators with this process. Feel free to contact us at WINDOWHelp@lbl.gov with questions or comments. NFRC Laminate Procedure Laminate Procedures (approved by NFRC) (PDF file) Approved Interlayer List (IGDB 33.0) (PDF file) NFRC Laminate Procedure Training Powerpoint with Examples (This Powerpoint presentation was used in the NFRC web based training sessions in December 2006 and January 2007) PowerPoint Presentation (PPT file) PowerPoint Presentation (PDF file) Help and Troubleshooting Error Messages The table below contains common warnings and error messages that may appear in Optics5 when calculating a laminate. Some of the messages can be ignored, and some are significant, which is indicated in the table.

387

NSLS Services | Shipping Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

NSLS Shipping Procedures For shipments arriving at the NSLS from other locations, please ship via Federal Express. If this is not possible, or if you have any questions, please...

388

PROCEDURE FOR PREPARING  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PROCEDURE FOR PREPARING PROCEDURE FOR PREPARING RECORDS INVENTORY AND DISPOSITION SCHEDULES (RIDS) Revision 1 November 1, 2007 Records Management Division, IM-23 PROCEDURE FOR PREPARING RECORDS INVENTORY AND DISPOSITION SCHEDULES (RIDS) 1. If the records have not yet been inventoried, see "Procedure for Conducting a Records Inventory." An inventory must be completed prior to preparing the RIDS. 2. The Records Inventory and Disposition Schedules (RIDS) should be reviewed and updated at least annually on DOE F 1324.10 and DOE F 1324.9. The RIDS covers all record, administrative and programmatic, as well as non- record material. The RIDS must include: a. Complete and detailed information identifying the organization (s) responsible for the records.

389

Operating Procedures Guideline  

Science Conference Proceedings (OSTI)

The intention of this report is to provide guidance for generating stations’ management and personnel striving for successful methods of developing effective operating procedures. Standard operating procedure management is used in most businesses and industries to assist in the safe and efficient operation of those companies. Effectively managing the program is essential in order to comply with mandatory regulations, maintain the highest possible level of plant integrity, minimize human ...

2012-12-12T23:59:59.000Z

390

Advanced Vehicle Testing Activity: Neighborhood Electric Vehicle...  

NLE Websites -- All DOE Office Websites (Extended Search)

Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Neighborhood Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced Vehicle...

391

Memorandum Memorializing Ex Parte Communication, DOE impending determination of coverage for commercial and industrial fans, blowers, and fume hoods.  

Energy.gov (U.S. Department of Energy (DOE))

The meeting was requested by AMCA International to introduce the association’s leadership, standards, and experience in developing fan standards to DOE; to learn more about the DOE process for...

392

Guidelines for Induced Flue Gas Recirculation: Volume 1: Reducing Air/Gas System Resistance and Enhancing Fan Capacity  

Science Conference Proceedings (OSTI)

This document guides users through a logical sequence, or "road map," of activities and decisions for optimizing solutions for fans, ducts, and related equipment in fossil plant combustion air and gas systems.

1999-12-13T23:59:59.000Z

393

Science on Saturday attracts science fans of all ages | Princeton Plasma  

NLE Websites -- All DOE Office Websites (Extended Search)

Science on Saturday attracts science fans of all ages Science on Saturday attracts science fans of all ages By Jeanne Jackson DeVoe January 28, 2013 Tweet Widget Facebook Like Google Plus One Joshua E. G. Peek, a Hubble Fellow at Columbia University's Department of Astronomy and son of PPPL physicist and former director Robert Goldston, discusses "Outer Space!" (Photo by Elle Starkman/PPPL Office of Communications) Joshua E. G. Peek, a Hubble Fellow at Columbia University's Department of Astronomy and son of PPPL physicist and former director Robert Goldston, discusses "Outer Space!" Gallery: High school senior Varuni Bewtra comes to the lectures to learn about possible careers in science. (Photo by Photo by Jeanne Jackson DeVoe/PPPL Office of Communications) High school senior Varuni Bewtra comes to the lectures to learn about

394

HEPA Filter Differential Pressure Fan Interlock System Functional Requirements and Technical Design Criteria  

SciTech Connect

Double-shell tanks (DSTs) and Double Contained Receiver Tanks (DCRTs) are actively ventilated, along with certain single-shell tanks (SSTs) and other RPP facilities. The exhaust air stream on a typical primary ventilation system is drawn through two stages of high-efficiency particulate air (HEPA) filtration to ensure confinement of airborne radioactive materials. Active ventilation exhaust stacks require a stack CAM interlock to detect releases from postulated accidents, and to shut down the exhaust fan when high radiation levels are detected in the stack airstream. The stack CAM interlock is credited as a mitigating control to stop continued unfiltered radiological and toxicological discharges from the stack, which may result from an accident involving failure of a HEPA filter. This document defines the initial technical design baseline for a HEPA filter AP fan interlock system.

TUCK, J.A.

2000-05-11T23:59:59.000Z

395

Improving Control of a Dual-Duct Single-Fan Variable Air Volume Systems  

E-Print Network (OSTI)

This paper discusses improved control strategies for dual-duct single-fan variable air volume (VAV) systems. Common control strategy for supply air volume modulation is evaluated, and an improved air volume control strategy that maintains separate cold and hot air duct static pressure set points is presented. The paper also explores the interactions between the cold and hot deck temperatures and duct static pressures, and discusses the impact of non-ideal deck temperature settings on duct static pressures and overall system energy consumption. To compensate the negative impact of non-ideal cold and hot deck temperature set points, the authors propose using real-time duct static pressure readings as feedback signals to fine-tune the deck temperature set points. These new control schemes can reduce simultaneous cooling and heating while reducing fan power consumption.

Wei, G.; Martinez, J.; Minihan, T.; Brundidge, T.; Claridge, D. E.; Turner, W. D.

2003-01-01T23:59:59.000Z

396

Awardee Share Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Awardee Share Procedures Awardee Share Procedures Procedures for Correctly Reporting Awardee Share on the FAADS/FAADS Plus reporting screen in STRIPES To ensure proper reporting by DOE to USASpending.gov, you must enter the awardee share (also known as the cost share, recipient share, and non-federal share) manually on the FAADS/FAADS Plus reporting screen in STRIPES. The FAADS/FAADS Plus file is the financial assistance equivalent of the FPDS-NG data entry for acquisition awards. The awardee share amount is not system generated on the FAADS/FAADS Plus reporting screen like the obligation amount is. The fields on the FAADS/FAADS Plus form which must be entered when reporting a Cost-share Financial Assistance Award are: Field #17 Non-Federal Funding Sign Choose 'Obligation', which refers to a positive amount (sign), or 'Deobligation', which refers to a

397

Radiation Emergency Procedure Demonstrations  

NLE Websites -- All DOE Office Websites (Extended Search)

Managing Radiation Emergencies Managing Radiation Emergencies Procedure Demonstrations Procedure Demonstrations Note: RealPlayer is needed for listening to the narration that accompany these demonstrations. Real Player Dressing To Prevent the Spread of Radioactive Contamination This demonstration shows how your team can dress to prevent the spread of radioactive contamination. Click to begin presentation on dressing to prevent the spread of radioactive contamination. Preparing The Area This demonstration shows basic steps you can take to gather equipment and prepare a room to receive a patient who may be contaminated with radioactive material. Click to begin presentation on preparing a room to receive a radioactive contaminated patient. Removing Contaminated Clothing This demonstration shows the procedure for removing clothing from a patient who may be contaminated with radioactive material.

398

Architectural characteristics of fine-grained submarine fans: A model applicable to the Gulf of Mexico  

Science Conference Proceedings (OSTI)

Submarine fan deposits in the Gulf of Mexico, modern and ancient, fall in the category of fine-grained, low overall sand/shale ratio basin-floor fans. Models published over the years that have been applied to both exploration and production are based on sand-rich fans, most of which were deposited in active margin settings. These models should not be used for the Gulf of Mexico or any other deep water system with similar basinal settings. Observations from the excellent outcrops of the Permian Tanqua Karoo in southwestern South Africa, together with information from the modern Mississippi Fan, and the Jackfork turbidites in Arkansas, enable the construction of a model that addresses the architecture of both the macro and meso-scale depositional features of fine-grained turbidite systems. At the entrance to the basin floor the conduit, carved out across the slope, may start to widen. Most of the density flows moving through do not necessarily occupy the conduit`s entire width. The result is a complex of laterally and vertically stacked channel fills and associated levee-overbank deposits with a good degree of connectivity. The channel fills are mostly massive, whereas the levee deposits are low-contrast, low-resistivity thin-bedded sandstones and shales with high permeability. Such sandstones can be potentially very productive. The channels gradually become smaller and as their influence on directing the heads of turbidity currents decreases, oblong sheet sands are deposited, each having a very large width to thickness ratio and a high sand/shale ratio. The vertical stacking patterns within these sheet sands commonly display lateral offset of individual beds or groups of beds, and therefore form a distinct reservoir type with varying internal fluid-flow characteristics.

Bouma, A.H.; Coleman, J.H. [Louisiana State Univ., Baton Rouge, LA (United States); DeV Wickens, H. [and others

1995-10-01T23:59:59.000Z

399

Random fan-out state induced by site-random interlayer couplings  

Science Conference Proceedings (OSTI)

We study the low-temperature properties of a classical Heisenberg model with site-random interlayer couplings on the cubic lattice. This model is introduced as a simplified effective model of Sr(Fe{sub 1-x}Mn{sub x})O{sub 2}, which was recently synthesized. In this material, when x=0.3, ({pi}{pi}{pi}) and ({pi}{pi}0) mixed ordering is observed by neutron diffraction measurements. Using Monte Carlo simulations, we find an exotic bulk spin structure that explains the experimentally obtained results. We name this spin structure the ''random fan-out state.'' The mean-field calculations provide an intuitive understanding of this phase being induced by the site-random interlayer couplings. Since Rietveld analysis assuming the random fan-out state agrees well with the neutron diffraction pattern of Sr(Fe{sub 0.7}Mn{sub 0.3})O{sub 2}, we conclude that the random fan-out state is reasonable for the spin-ordering pattern of Sr(Fe{sub 0.7}Mn{sub 0.3})O{sub 2} at the low-temperature phase.

Tamura, Ryo; Kawashima, Naoki; Yamamoto, Takafumi; Tassel, Cedric; Kageyama, Hiroshi [Institute for Solid State Physics, University of Tokyo, 5-1-5 Kashiwa-no-ha, Kashiwa, Chiba 277-8581 (Japan); Department of Energy and Hydrocarbon Chemistry, Graduate School of Engineering, Kyoto University, Nishikyouku, Kyoto 615-8510 (Japan)

2011-12-01T23:59:59.000Z

400

Final test report: demonsration testing in support of the Track 3system waste dislodging, retrieval and conveyance concepts  

SciTech Connect

This report contains the quantitative and qualitative data and information collected during performance of the Track 3 System testing protocol. Information contained herein focuses on the data collected during performance ofthe following Tests Procedures. *Test Procedure-1, Position Management Test Procedure-2, Waste Dislodging, Retrieval, and Conveyance and Decontamination *Test Procedure-3, Dynamic Response Test procedures, Safety Demonstration

Berglin, E.J.

1997-07-24T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Advanced Vehicle Testing Activity: Urban Electric Vehicle Specificatio...  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Urban Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced Vehicle...

402

Advanced Vehicle Testing Activity: Hybrid Electric Vehicle Specificati...  

NLE Websites -- All DOE Office Websites (Extended Search)

Test Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Hybrid Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced Vehicle...

403

Advanced Vehicle Testing Activity: Oil Bypass Filter Specifications...  

NLE Websites -- All DOE Office Websites (Extended Search)

and Test Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Oil Bypass Filter Specifications and Test Procedures on Facebook Tweet about Advanced...

404

Precipitator Performance Estimation Procedure  

Science Conference Proceedings (OSTI)

Increased availability of data to use with an existing computer model makes it possible for utilities to calculate electrostatic precipitator performance without access to industry databases. This report examines the accuracy of the model and develops procedures to make it a more useful tool for troubleshooting precipitator performance and for selecting the size of a new unit.

1986-12-22T23:59:59.000Z

405

Economic Recovery of Oil Trapped at Fan Margins Using Hig Angle Wells Multiple Hydraulic Fractures  

Science Conference Proceedings (OSTI)

The Yowlumne field is a giant field in the southern San Joaquin basin, Kern County, California. It is a deep (13,000 ft) waterflood operation that produces from the Miocene- aged Stevens Sand. The reservoir is interpreted as a layered, fan-shaped, prograding turbidite complex containing several lobe-shaped sand bodies that represent distinct flow units. A high ultimate recovery factor is expected, yet significant quantities of undrained oil remain at the fan margins. The fan margins are not economic to develop using vertical wells because of thinning pay, deteriorating rock quality, and depth. This project attempts to demonstrate the effectiveness of exploiting the northeast distal fan margin through the use of a high- angle well completed with multiple hydraulic- fracture treatments. A high-angle well offers greater pay exposure than can be achieved with a vertical well. Hydraulic-fracture treatments will establish vertical communication between thin interbedded layers and the wellbore. The equivalent production rate and reserves of three vertical wells are anticipated at a cost of approximately two vertical wells. The near-horizontal well penetrated the Yowlumne sand; a Stevens sand equivalent, in the distal fan margin in the northeast area of the field. The well was drilled in a predominately westerly direction towards the interior of the field, in the direction of improving rock quality. Drilling and completion operations proved to be very challenging, leading to a number of adjustments to original plans. Hole conditions resulted in obtaining less core material than desired and setting intermediate casing 1200 ft too high. The 7 in. production liner stuck 1000 ft off bottom, requiring a 5 in. liner to be run the rest of the way. The cement job on the 5 in. liner resulted in a very poor bond, which precluded one of three hydraulic fracture treatments originally planned for the well. Openhole logs confirmed most expectations going into the project about basic rock properties: the formation was shaly with low porosities, and water saturations were in line with expectations, including the presence of some intervals swept out by the waterflood. High water saturations at the bottom of the well eliminated one of the originally planned hydraulic fracture treatments. Although porosities proved to be low, they were more uniform across the formation than expected. Permeabilities of the various intervals continue to be evaluated, but appear to be better than expected from the porosity log model derived in Budget Period One. The well was perforated in all pay sections behind the 5 in. liner. Production rates and phases agree nicely with log calculations, fractional flow calculations, and an analytical technique used to predict the rate performance of the well.

Laue, M.L.

1997-11-21T23:59:59.000Z

406

High-amplitude reflection packets (HARPs) of the Mississippi Fan, Gulf of Mexico  

E-Print Network (OSTI)

Examination of seismic data from the deep-water Gulf of Mexico reveals the presence of High-Amplitude Reflection Packets (HARPs). An analog study conducted by the Ocean Drilling Program Leg 155 identified and described Amazon Fan HARPs as a stacked, relatively unconfined series of graded turbidites overlain by a channel-levee. HARP seismic facies thin laterally and onlap antecedent bathymetry (preexisting submarine topography). HARP areal extent is controlled by antecedent bathymetry and turbidity flow sediment volumes. Mississippi Fan HARP deposition can be described by three depositional models: the "avulsion" model, the "fill and spill" model, and the "transition" model. The "avulsion" depositional model, developed by Flood et al. (1991), describes avulsion of submarine channel-levees by turbidity flows. Subsequent turbidity flows exit the channel-levee at the avulsion point and are deposited as unchannelized HARPs. The "fill and spill" model, developed by Satterfield and Behrens (1990), describes turbidite deposition in the Gulf of Mexico salt province. Initial stages of the "fill and spill" model accurately describe the seismic geometries of HARPs confined by adjacent salt structures. The "transition" model was developed in this study to describe the Gulf of Mexico HARP seismic geometries seen in the transition zone from the salt province to the abyssal plain. The HARPs described by the "transition" model contain an upslope segment confined by salt structures and a downslope segment confined by antecedent bathymetry. Utilizing seismic data from the Gulf of Mexico and core and well-log data from the Amazon Fan, this study has determined that HARPs and related channel-levees have hydrocarbon play potential. HARP sheet sands, internal HARP channel fill, overlying channel-levee fill, and overbank levee sands are potential reservoir units. Detrital carbonate and hemipelagic shale source rocks are in place in the deep-water Gulf of Mexico. In addition, structurally derived migration pathways combine with percolation as potential migration processes. This study integrates identification and description of HARP seismic facies relationships, current and newly developed depositional models, interpretation of stratigraphic controls, HARP internal reservoir architecture, and determination of HARP hydrocarbon potential in order to predict HARP deposition in the Mississippi Fan and other mud-rich fans worldwide.

Francis, Jason Michael

2000-01-01T23:59:59.000Z

407

Emergency Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Services Employee Services Safety and Health Emergency Procedures Emergency Procedures Note: This page is pending deletion, please refer to the Safety and health main page...

408

Advanced Rooftop Control (ARC) Retrofit: Field-Test Results  

Science Conference Proceedings (OSTI)

The multi-year research study was initiated to find solutions to improve packaged equipment operating efficiency in the field. Pacific Northwest National Laboratory (PNNL), with funding from the U.S. Department of Energy’s (DOE’s) Building Technologies Office (BTO) and Bonneville Power Administration (BPA) conducted this research, development and demonstration (RD&D) study. Packaged equipment with constant speed supply fans is designed to provide ventilation at the design rate at all times when the fan is operating as required by building code. Although there are a number of hours during the day when a building may not be fully occupied or the need for ventilation is lower than designed, the ventilation rate cannot be adjusted easily with a constant speed fan. Therefore, modulating the supply fan in conjunction with demand controlled ventilation (DCV) will not only reduce the coil energy but also reduce the fan energy. The objective of this multi-year research, development and demonstration project was to determine the magnitude of energy savings achievable by retrofitting existing packaged rooftop air conditioners with advanced control strategies not ordinarily used for packaged units. First, through detailed simulation analysis, it was shown that significant energy (between 24% and 35%) and cost savings (38%) from fan, cooling and heating energy consumption could be realized when packaged air conditioning units with gas furnaces are retrofitted with advanced control packages (combining multi-speed fan control, integrated economizer controls and DCV). The simulation analysis also showed significant savings for heat pumps (between 20% and 60%). The simulation analysis was followed by an extensive field test of a retrofittable advanced rooftop unit (RTU) controller.

Wang, Weimin; Katipamula, Srinivas; Ngo, Hung; Underhill, Ronald M.; Taasevigen, Danny J.; Lutes, Robert G.

2013-07-31T23:59:59.000Z

409

NEV PROCEDURE PUNCH LIST  

NLE Websites -- All DOE Office Websites (Extended Search)

END OF LIFE TEST SEQUENCE Revision 0 September 1, 2006 Prepared by Electric Transportation Applications Prepared by: Date: Roberta Brayer...

410

NEV PROCEDURE PUNCH LIST  

NLE Websites -- All DOE Office Websites (Extended Search)

BASELINE TEST SEQUENCE Revision 1 September 1, 2006 Prepared by Electric Transportation Applications Prepared by: Date: Roberta Brayer...

411

NEV PROCEDURE PUNCH LIST  

NLE Websites -- All DOE Office Websites (Extended Search)

NEVAmerica TEST SEQUENCE Revision 2 Effective February 1, 2008 Prepared by Electric Transportation Applications Prepared by: Date: Nick...

412

TRANSPARENCY RECYCLING PROGRAM PROCEDURES  

NLE Websites -- All DOE Office Websites (Extended Search)

TRANSPARENCY RECYCLING Don't throw out your used overhead transparencies! RECYCLE them for REUSE. It's Easy! Follow these simple procedures: 1.) COLLECT used transparencies to be recycled. 2.) SEPARATE the transparencies from ringed binders, plastic or paper folders, envelopes, and/or files. 3.) PLACE the transparencies (only) into an intra-laboratory mail envelope. 4.) SEND the envelope to: Terri Schneider, Building 201, 1D-10. Terri will prepare a

413

DOE Reasonable Accommodation Procedures  

Energy.gov (U.S. Department of Energy (DOE))

Pursuant to Executive Order 13164, the Department of Energy (hereinafter referred to as the “department”), is charged with establishing written procedures for the facilitation of reasonable accommodation for: (1) individuals with disabilities in the application process for employment with the Department; (2) Department employees with disabilities to perform the essential functions of a position; and (3) Department employees with disabilities to enjoy benefits and privileges of employment equal to those enjoyed by employees without disabilities.

414

CMS System Security Plan Procedure  

Science Conference Proceedings (OSTI)

... TASK 5: SYSTEM DECOMMISSION. ... BPSSM Business Partners Systems Security Manual. ... of Information Technology, Policy, Procedures, & Audits. ...

2009-06-30T23:59:59.000Z

415

Comparisons of field performance to closed-door test T ABLE 1 ratings indicate the laboratory procedure is a valid indica-Design Options to Improve the Energy Efficiency of a  

E-Print Network (OSTI)

#12;#12;Comparisons of field performance to closed-door test T ABLE 1 ratings indicate commercially manufactured refrigerators were u~ as laboratory test beds, a testing sequence of ..as PHASE I cabinets with an optimized Option 2 Evaporator/condenser size, surface r~frige~tion circuit or cvcle were

Oak Ridge National Laboratory

416

Active Noise Control of a Two-Fan Exhaust-Mounted Array Using Near-Field Control Sources and Error Sensors.  

E-Print Network (OSTI)

??Multiple fans are sometimes used in an array configuration to cool various types of electronic equipment. In addition to adding another noise source, using two… (more)

Rust, Ryan Leonard 1982-

2010-01-01T23:59:59.000Z

417

Reason and reaction: The dual route of decision making process on social media usage: The case of hospitality brand fan pages.  

E-Print Network (OSTI)

??A new phenomenon on Facebook, resulting from social media revolution, is the emergence of numerous Facebook fan pages. This form of online brand community is… (more)

Manthiou, Aikaterini

2012-01-01T23:59:59.000Z

418

Strategy for the Operation of Cooling Towers with variable Speed Fans  

E-Print Network (OSTI)

Within the SPS Cooling Water Project at CERN aimed at the reduction of water consumption, this primary open cooling loop will be closed and all the primary cooling circuit components will be upgraded to the new required duty and brought to the necessary safety and operability standards. In particular the tower fans will be fitted with variable frequency drives to replace the existing two speed motors. This paper presents a study to optimize the operation of SPS cooling towers taking into account outdoor conditions (wet and dry bulb temperatures) and the entirety of the primary circuit in which they will operate.

Iñigo-Golfín, J

2001-01-01T23:59:59.000Z

419

Busemann functions and the speed of a second class particle in the rarefaction fan  

E-Print Network (OSTI)

In this paper we will show how the results found in Cator and Pimentel 2009, about the Busemann functions in last-passage percolation, can be used to calculate the asymptotic distribution of the speed of a single second class particle starting from an arbitrary deterministic configuration which has a rarefaction fan, in either the totally asymetric exclusion process, or the Hammersley interacting particle process. The method will be to use the well known last-passage percolation description of the exclusion process and of the Hammersley process, and then the well known connection between second class particles and competition interfaces.

Eric Cator; Leandro P. R. Pimentel

2010-08-10T23:59:59.000Z

420

SANS Training Voucher Program Registration Procedures | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SANS Training Voucher Program Registration Procedures SANS Training Voucher Program Registration Procedures SANS Training Voucher Program Registration Procedures For Federal...

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

FANS - Principle  

Science Conference Proceedings (OSTI)

... detecting all scattered neutrons with energy Ef energies, with moderate ... which changes to optimize intensity during the ...

422

FANS - Overview  

Science Conference Proceedings (OSTI)

... Pyrolytic Graphite [PG(002)], Without small shield: 2.5 meV ? E ? 25.0 meV With small shield: 3.7 meV ? E ? 45.0 meV. ...

423

Records Management Exit Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Exit Procedures For Departing Federal and contractor Employees PRESERVATION OF FEDERAL RECORDS The Federal Records Act requires the Department of Energy (DOE) Records Officer to remind departing Federal and contractor employees that Federal records may not be removed from Government custody nor may they be destroyed except in accordance with a records disposition schedule that has been approved by the Archivist of the United States. The creation of adequate documentation and the preservation of Federal records are required by law and regulation (contained in 36 CFR Chapter XII). As Federal and contractor employees, you have Federal record-keeping responsibilities that are regulated by the National Archives and Records Administration (NARA) to ensure the retention and

424

Influence of provenance on detrital and diagenetic mineralogy of small tertiary fans in southwestern Montana  

SciTech Connect

In the North Boulder River basin in southwestern Montana, alluvial fans of the Renova (Oligocene-Miocene) and the Sixmile Creek (Miocene) Formations were deposited on the flanks of north-south-trending uplifts that also supplied the detritus. The Elkhorn Mountain volcanics (78 m.y.) overlying the Boulder batholith make up the western highlands, a small patch of Precambrian Belt Group rocks occur in the southwest and Paleozoic siliciclastic and carbonate rocks forming the eastern margin. The fan sediments thus allow adequate control for studying the influence of source rocks on detrital and diagenetic mineralogy. Modal analysis of 6228 grains in 31 thin sections shows a decrease of VRF away from the igneous sources (37% to 1% in a north-south transect; 37% to 7% in a west-east transect) along with an increase in quartz (8% to 24% and 3% to 13%) and plagioclase (2% to 16% and 2% to 10%); orthoclase abundance is low except in the southwest. Volcanic ash and glass shards are found in the younger sediments in the northern part of the basin. Their data show a positive correlation between the abundance of orthoclase and kaolinite (north-south transect); between SRF and carbonate cement (west-east transect) and between glass shards and smectite (both north-south and west-east transects). They infer that the diagenetic mineralogy of these sands was controlled essentially by the detrital particles, which were strongly controlled by source rocks in this area.

Olson, J.; Basu, A.

1987-05-01T23:59:59.000Z

425

Correlation efficiency as a tool to establish depositional subenvironments in submarine fans  

Science Conference Proceedings (OSTI)

Depositional units in submarine fan systems commonly are too large to be entirely or sufficiently exposed in an outcrop to properly identify. Channel fills can be massive, bedded, or any combination thereof. The layering can be horizontal or inclined. Typical bedded series can be thick or thin bedded, or a combination with or without a certain cyclicity. Occurrence of sedimentary structures is not yet a decisive interpretation characteristic. At the present, the Lower Permian Skoorsteenberg Formation of the Southwest Karoo in South Africa may be the best example of long, nontilted, outcrops where entire subenvironments can be observed. Using that knowledge, outcrop information from several areas, and ideas from the literature, we attempted correlations in two spillways in the Jackfork Group in Arkansas. A layer-by-layer correlation failed, even after small layer package could be established using an occasional thick shale break, a major slump, or a very thick massive sandstone layer for dividing both sides of the spillway. A [open quotes]semi-logarithmic[close quotes] display of measured thickness provides patterns of variations in layer thickness that normally are sufficiently typical to use as a correlation tool between both sides. This is not a foolproof system and one should consider additional parameters, such as location within the entire fan system. However, the degree of correlatibility helps identify or suggest depositional environments.

Bouma, A.H.; Cook, T.W. (Louisiana State Univ., Baton Rouge, LA (United States)); Devries, M.B. (Exxon Exploration Company, Houston, TX (United States))

1993-09-01T23:59:59.000Z

426

Effect of building airtightness and fan size on the performance of mechanical ventilation systems in new U.S. houses: a critique of ASHRAE standard 62.2-2003  

E-Print Network (OSTI)

as sizing a fan to deliver the design ventilation rate (fans and natural infiltration, in order to properly designfans should be as small as necessary to deliver the effective design

Roberson, J.

2004-01-01T23:59:59.000Z

427

Advanced Vehicle Testing Activity: Full-Size Electric Vehicle...  

NLE Websites -- All DOE Office Websites (Extended Search)

Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Full-Size Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced Vehicle...

428

Advanced Vehicle Testing Activity: Plug-in Hybrid Electric Vehicle...  

NLE Websites -- All DOE Office Websites (Extended Search)

Procedures to someone by E-mail Share Advanced Vehicle Testing Activity: Plug-in Hybrid Electric Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced...

429

Presidential Permits - Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Permits - Procedures Presidential Permits - Procedures Electricity Advisory Committee Technology Development Electricity Policy Coordination and Implementation Transmission...

430

VELOCITY MEASUREMENTS FOR A SOLAR ACTIVE REGION FAN LOOP FROM HINODE/EIS OBSERVATIONS  

Science Conference Proceedings (OSTI)

The velocity pattern of a fan loop structure within a solar active region over the temperature range 0.15-1.5 MK is derived using data from the EUV Imaging Spectrometer (EIS) on board the Hinode satellite. The loop is aligned toward the observer's line of sight and shows downflows (redshifts) of around 15 km s{sup -1} up to a temperature of 0.8 MK, but for temperatures of 1.0 MK and above the measured velocity shifts are consistent with no net flow. This velocity result applies over a projected spatial distance of 9 Mm and demonstrates that the cooler, redshifted plasma is physically disconnected from the hotter, stationary plasma. A scenario in which the fan loops consist of at least two groups of 'strands'-one cooler and downflowing, the other hotter and stationary-is suggested. The cooler strands may represent a later evolutionary stage of the hotter strands. A density diagnostic of Mg VII was used to show that the electron density at around 0.8 MK falls from 3.2 Multiplication-Sign 10{sup 9} cm{sup -3} at the loop base, to 5.0 Multiplication-Sign 10{sup 8} cm{sup -3} at a projected height of 15 Mm. A filling factor of 0.2 is found at temperatures close to the formation temperature of Mg VII (0.8 MK), confirming that the cooler, downflowing plasma occupies only a fraction of the apparent loop volume. The fan loop is rooted within a so-called outflow region that displays low intensity and blueshifts of up to 25 km s{sup -1} in Fe XII {lambda}195.12 (formed at 1.5 MK), in contrast to the loop's redshifts of 15 km s{sup -1} at 0.8 MK. A new technique for obtaining an absolute wavelength calibration for the EIS instrument is presented and an instrumental effect, possibly related to a distorted point-spread function, that affects velocity measurements is identified.

Young, P. R. [College of Science, George Mason University, 4400 University Drive, Fairfax, VA 22030 (United States); O'Dwyer, B.; Mason, H. E. [Department of Applied Mathematics and Theoretical Physics, University of Cambridge, Wilberforce Road, Cambridge, CB3 0WA (United Kingdom)

2012-01-01T23:59:59.000Z

431

NIST Assists with Testing Crash Avoidance System  

Science Conference Proceedings (OSTI)

NIST Assists with Testing Crash Avoidance System. ... of Transportation (DOT) by developing tests for a ... has designed preliminary test procedures that ...

2012-12-13T23:59:59.000Z

432

Phase 2 Development of Procedure Usability Measurement Process (PUMP) Method  

Science Conference Proceedings (OSTI)

Usability problems with plant procedures contribute to a large percentage of errors committed by plant technicians, factor into more than half of all licensee event reports (LERs), and cost an average plant as much as $1M annually. This report outlines in detail EPRI's Procedure Usability Measurement Process (PUMP) method -- a package of standardized testing instruments for measuring the usability of plant procedures -- and describes its successful application at two plants.

1998-07-31T23:59:59.000Z

433

Overview Paper on In-Situ Testing -Singapore Workshop, Nov. 29-Dec. 01,2006 -P.W. Mayne -Page 1 1 INTRODUCTION  

E-Print Network (OSTI)

........................................................................................256 Sampler and Other Test Apparatus Materials ...............................................................................278 Manual Sampling Procedures..............................................................................................313 Sediment Sampling Procedures

Mayne, Paul W.

434

A high-resolution 2-DH numerical scheme for process-based modeling of 3-D turbidite fan stratigraphy  

Science Conference Proceedings (OSTI)

A generic three-dimensional process-based model is presented, aimed at simulation of the construction of turbidite fan stratigraphy by low-density turbidity current events. It combines theoretical formulations on density flow and sediment transport of ... Keywords: MacCormack scheme, Operator splitting, Shock-capturing technique, Stratigraphic modeling, Turbidite reservoirs, Turbidity currents

Remco M. Groenenberg; Kees Sloff; Gert Jan Weltje

2009-08-01T23:59:59.000Z

435

Study of the Effects of Ambient Conditions Upon the Performance of Fan Powered, Infrared Natural Gas Burners  

SciTech Connect

The objective of this investigation was to characterize the operation of a fan-powered, infrared burner (IR burner) at various gas compositions and ambient conditions, develop numerical model to simulate the burner performances, and provide design guidelines for appliances containing PIR burners for satisfactory performance.

Clark Atlanta University

2002-12-02T23:59:59.000Z

436

Towards a syntactic signature for domain models: proposed descriptive metrics for visualizing the entity fan-out frequency distribution  

Science Conference Proceedings (OSTI)

The main objective of this paper is to find a minimal set of measures that allow the immediate, intuitive characterisation and visualization of the syntactic structure of models covering a particular application domain. The measures are validated ... Keywords: case measures, enterprise models, entity fan-out distribution, metrics, model analysis, model complexity, modelling

Jean-Paul van Belle

2002-09-01T23:59:59.000Z

437

Optimized Fan Control In Variable Air Volume HVAC Systems Using Static Pressure Resets: Strategy Selection and Savings Analysis  

E-Print Network (OSTI)

The potential of static pressure reset (SPR) control to save fan energy in variable air volume HVAC systems has been well documented. Current research has focused on the creation of reset strategies depending on specific system features. As the commissioning process has begun to require the prediction of savings, knowledge of the extent to which various SPR control strategies impact fan energy has become increasingly important. This research aims to document existing SPR control strategies and utilize building data and simulation to estimate fan energy use. A comprehensive review of the literature pertaining to SPR control was performed and the results were organized into a top-down flow chart tool. Based on the type of feedback available from a particular system, or lack thereof, this tool will facilitate the selection of a SPR control strategy. A field experiment was conducted on a single duct variable air volume system with fixed discharge air temperature and static pressure setpoints. Finally, an air-side model of the experimental system was created using detailed building design information and calibrated using field measurements. This model was used to estimate the fan energy required to supply the trended airflow data using fixed static pressure (FSP) and SPR control based on zone demand, system demand, and outside air temperature. While utilizing trend data from November 1, 2008 to February 12, 2009, the FSP control of the experimental system was used as the baseline for ranking the energy savings potential of nine different forms of duct static pressure control. The highest savings (73-74%) were achieved using zonal demand based SPR control. System demand based SPR control yielded savings ranging from 59 to 76%, which increased when the duct sensor was positioned near the fan discharge and under similar zone load conditions. The outside air temperature based SPR control yielded savings of 65% since the experimental system supplied primarily perimeter zones. Finally, increasing the FSP setpoint from 2 to 3 inWG increased fan energy by 45%, while decreasing the setpoint from 2 to 1 inWG decreased fan energy by 41%.

Kimla, John

2009-12-01T23:59:59.000Z

438

Sand-rich submarine fans, Mio-Pliocene of Santa Monica Basin, offshore California: Untapped exploration targets  

Science Conference Proceedings (OSTI)

Santa Monica Basin lies directly west of Los Angeles Basin, one of the world's most prolific oil provinces. Published literature suggests that Santa Monica Basin was starved of coarse clastics during the late Miocene through Pliocene. However, seismic sequence stratigraphy indicates that deposition of sand-rich fans alternated with mixed-load systems throughout the Delmontian and Repettian stages. Seismic sequences and facies are calibrated to seismic and well data from Beta Oil Field, in San Pedro Basin to the south. Eustasy evidently played a dominant role in controlling sedimentation. Variations in tan lithology, thickness, and basinward extent correspond to worldwide changes in sea level. Regional erosion surfaces apparently signify drops in sea level. Overlying thick seismic packages display hummocky to chaotic seismic facies separated by high- to low-amplitude continuous reflections. These configurations are interpreted as inner- to mid-fan channels separated by overbank deposits in sand-rich lowstand fans. High-amplitude basinwide reflections bound the tops of the sand-rich intervals, and likely represent condensed sections formed during sea-level rises. Thin seismic intervals above the condensed sections display downlap, and are interpreted as interbedded sandstones and shales of prograding highstand fans. Sediment input to Santa Monica Basin, based on seismic-facies and isochron patterns, was predominantly from the (present-day) north, with subordinate input from the east. High-amplitude eustatic variations dominated deposition and sequence development even in this tectonically active basin Previously unidentified sand-rich fans are present, and have not been drilled.

May, J.A.; McMillen, K.J.

1996-01-01T23:59:59.000Z

439

Procedures for sprinkler anchor installation on surfaces with fireproofing materials  

SciTech Connect

Procedures were developed for limiting the release of fibers from fireproofing material during sprinkler hanger anchor installation on steel deck/concrete floor slab surfaces. These procedures were needed by the General Services Administration (GSA) for installation of sprinkler systems in buildings having fireproofing containing asbestos. A prototype floor slab having spray-on friable mineral wool fireproofing was used in laboratory tests. The mineral-wool fireproofing was used as a model system for fireproofing containing asbestos. The various combinations of mechanical anchoring procedures (use of drills or powder-actuated gun) and encapsulation procedures tested limited the fiber release to a range of values of 0.000 to 0.055 f/cc (fibers per cubic centimeter) as compared to a range of values of 0.26 to 0.82 f/cc for procedures without encapsulation. Encapsulation was shown to be effective as evidenced by much higher levels of fiber release during testing without encapsulation. Because there is no known correlation between the release of mineral-wool fibers and asbestos fibers, it was recommended that the procedures developed be evaluated by GSA in buildings having fireproofing containing asbestos. An air-sampling protocol was developed for use by GSA in evaluating the procedures in the field. Subsequently field tests were conducted by GSA. The laboratory and field studies provided GSA with an effective procedure, measurement method, and decision tool for installing sprinkler hanger anchors in steel deck/concrete floor slabs having fireproofing materials.

Mathey, R.G.; Knab, L.I.; Gross, J.L.; Small, J.A.

1988-02-01T23:59:59.000Z

440

WSDOT Test Method T 127 Preparation of Leachate Sample for Testing Toxicity of HECP Effluents 1. Scope This test method outlines the procedure for collecting leachate from a HECP sample. 2. References 2.1 EPA-821-R-02-012 Methods for Measuring Acute Toxic  

E-Print Network (OSTI)

3.1 Lay cheesecloth over clean topsoil 3.2 Apply the HECP to the cheesecloth at the following coverage: 3.2.1 HECP Long-Term or Moderate-Term Mulch 3,500 lbs per acre in two lifts with no more than 2000 # per acre in any one lift. 3.2.2 HECP Short-Term Mulch 2000 # per acre minimum, or manufacturer’s recommended rate may be used. 3.3 Allow material to cure for 48 hours 3.4 Pull cheesecloth up with mat of HECP, brush off any soil 3.5 Cut HECP into squares and provide 1.02 pounds of HECP to the laboratory. 4. Preparation of the Leachate (done by the laboratory) 4.1 Allow hydromulch product to soak in water for one hour 4.2 Remove hydromulch sheet from water 4.3 Filter water through a 60 micron filter – water may be pre-filtered through a 35 mesh and then a 120 mesh before using the 230 mesh/63 micron filter. Note: Leachate not immediately used for testing should be stored at 4 ° C in the dark until

unknown authors

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Microsoft Word - ACEEE_08_FurnaceBlower_Paper484_2008-05-16_...  

NLE Websites -- All DOE Office Websites (Extended Search)

widely and that the static pressure used in the test procedure as well as the calculated fan power is not representative of actual field installations. Therefore, accurate...

442

Standby power use: How big is the problem? What policies and technical solutions can address it?  

E-Print Network (OSTI)

as clothes washers, dishwashers, and room air conditioners.clothes washers, dishwashers, microwaves, ceiling fans withthe end of 2003. The dishwasher test procedure has already

2002-01-01T23:59:59.000Z

443

Department of Energy Technical Standards Procedures | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department of Energy Technical Standards Procedures Department of Energy Technical Standards Procedures DOE Technical Standards Program The following procedures should be used to...

444

Procedure for Planning and Conducting  

NLE Websites -- All DOE Office Websites (Extended Search)

Lift Plan Procedure Lift Plan Procedure Stanford Synchrotron Radiation Laboratory Lead Author __________________________________ Date 07/13/2005___________ David A. Ernst Mechanical Service Group Approvals: __________________ Date _____________________ Matt Padilla SSRL Safety Officer __________________ Date _____________________ Robert Hettel Accelerator System Department Head __________________ Date _____________________ Piero Pianetta Beam Line System Department Head Hoist and Rigging Panel Member _______________________________________ Date ______________________

445

Specific test and evaluation plan  

SciTech Connect

The purpose of this Specific Test and Evaluation Plan (STEP) is to provide a detailed written plan for the systematic testing of modifications made to the 241-AX-B Valve Pit by the W-314 Project. The STEP develops the outline for test procedures that verify the system`s performance to the established Project design criteria. The STEP is a lower tier document based on the W-314 Test and Evaluation Plan (TEP). Testing includes Validations and Verifications (e.g., Commercial Grade Item Dedication activities), Factory Acceptance Tests (FATs), installation tests and inspections, Construction Acceptance Tests (CATs), Acceptance Test Procedures (ATPs), Pre-Operational Test Procedures (POTPs), and Operational Test Procedures (OTPs). It should be noted that POTPs are not required for testing of the transfer line addition. The STEP will be utilized in conjunction with the TEP for verification and validation.

Hays, W.H.

1998-03-20T23:59:59.000Z

446

Model of Procedure Usage – Results from a Qualitative Study to Inform Design of Computer-Based Procedures  

SciTech Connect

The nuclear industry is constantly trying to find ways to decrease the human error rate, especially the human errors associated with procedure use. As a step toward the goal of improving procedure use performance, researchers, together with the nuclear industry, have been looking at replacing the current paper-based procedures with computer-based procedure systems. The concept of computer-based procedures is not new by any means; however most research has focused on procedures used in the main control room. Procedures reviewed in these efforts are mainly emergency operating procedures and normal operating procedures. Based on lessons learned for these previous efforts we are now exploring a more unknown application for computer based procedures - field procedures, i.e. procedures used by nuclear equipment operators and maintenance technicians. The Idaho National Laboratory, the Institute for Energy Technology, and participants from the U.S. commercial nuclear industry are collaborating in an applied research effort with the objective of developing requirements and specifications for a computer-based procedure system to be used by field operators. The goal is to identify the types of human errors that can be mitigated by using computer-based procedures and how to best design the computer-based procedures to do this. The underlying philosophy in the research effort is “Stop – Start – Continue”, i.e. what features from the use of paper-based procedures should we not incorporate (Stop), what should we keep (Continue), and what new features or work processes should be added (Start). One step in identifying the Stop – Start – Continue was to conduct a baseline study where affordances related to the current usage of paper-based procedures were identified. The purpose of the study was to develop a model of paper based procedure use which will help to identify desirable features for computer based procedure prototypes. Affordances such as note taking, markups, sharing procedures between fellow coworkers, the use of multiple procedures at once, etc. were considered. The model describes which affordances associated with paper based procedures should be transferred to computer-based procedures as well as what features should not be incorporated. The model also provides a means to identify what new features not present in paper based procedures need to be added to the computer-based procedures to further enhance performance. The next step is to use the requirements and specifications to develop concepts and prototypes of computer-based procedures. User tests and other data collection efforts will be conducted to ensure that the real issues with field procedures and their usage are being addressed and solved in the best manner possible. This paper describes the baseline study, the construction of the model of procedure use, and the requirements and specifications for computer-based procedures that were developed based on the model. It also addresses how the model and the insights gained from it were used to develop concepts and prototypes for computer based procedures.

Johanna H Oxstrand; Katya L Le Blanc

2012-07-01T23:59:59.000Z

447

Economic recovery of oil trapped at fan margins using high angle wells and multiple hydraulic fractures. Quarterly report, July 1--September 30, 1997  

SciTech Connect

This project attempts to demonstrate the effectiveness of exploiting thin-layered, low-energy deposits at the distal margin of a prograding turbidite complex through the use of hydraulically fractured horizontal or high-angle wells. The combination of a horizontal or high-angle well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. A high-angle well will be drilled in the fan-margin portion of a slope-basin clastic reservoir and will be completed with multiple hydraulic-fracture treatments. Geologic modeling, reservoir characterization, and fine-grid reservoir simulation will be used to select the well location and orientation. Design parameters for the hydraulic-fracture treatments will be determined, in part, by fracturing an existing test well. Fracture azimuth will be predicted by passive seismic monitoring of a fracture-stimulation treatment in the test well using logging tools in an offset well. The long radius, near horizontal well has been drilled. After pumping a remedial cement squeeze, all pay behind the 5 in. liner was perforated and stimulated. Once wellwork is complete for the existing perforations, a hydraulic fracture treatment will be pumped through a short interval of clustered perforations in the 7 in. liner. Following this frac, all pay behind the 7 in. liner will be perforated and completion operations will be final.

Laue, M.L.

1997-10-30T23:59:59.000Z

448

Records Management Exit Procedures | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

leave. Records Management Exit Procedures More Documents & Publications Records Management Exit Procedures Operational Plan and Desktop Reference for the Veterans...

449

External > Programs > Environmental Management > Policies & Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Policies & Procedures This website offers Environmental Management (EM) operating policies, procedures, standards, workaids, organizational charts, and other pertinent documents...

450

The Fallout between Procedure and Practice  

E-Print Network (OSTI)

OF CALIFORNIA SANTA CRUZ The Fallout between procedure andAurora Olmos-Gallo The Fallout Between Procedure and

Olmos-Gallo, Aurora Maria

2013-01-01T23:59:59.000Z

451

Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and  

Open Energy Info (EERE)

Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and Testing in Geothermal Exploration Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and Testing in Geothermal Exploration Abstract No abstract prepared. Authors Jim Combs, John T. Finger, Colin Goranson, Charles E. Hockox Jr., Ronald D. Jacobsen and Gene Polik Organization Sandia National Laboratories Published Geothermal Technologies Legacy Collection, 1999 Report Number SAND99-1976 DOI Not Provided Check for DOI availability: http://crossref.org Online Internet link for Slimhole Handbook- Procedures and Recommendations for Slimhole Drilling and Testing in Geothermal Exploration Citation

452

J.L. Liscum-Powell, S.D. Pautz, C.R. Drumm, W.C. Fan, W.J. Bohnhoff...  

National Nuclear Security Administration (NNSA)

of the Ceptre Code to Cable SGEMP Problems J.L. Liscum-Powell, * S.D. Pautz, * C.R. Drumm, * W.C. Fan, * W.J. Bohnhoff, * L.J. Lorence * * Sandia National Laboratories,...

453

Performance Optimization of a Fan System- Overcoming Impacts of Modified Design Criteria Due to Regulatory Requirements and Changed Operating Conditions  

E-Print Network (OSTI)

The Louisiana Pacific mill in Tomahawk Wisconsin manufactures oriented-strand board. Several large induced-draft fans and combustion-air blowers were operating inefficiently at this mill. This case study highlights a systems approach that was applied to address fan inefficiency. Energy savings from optimizing the system are estimated to be 338 kW, nearly half of the original measured input power of 678 kW. The project is currently being implemented and will have a payback period of less than 8 months. The opportunities here are typical of opportunities thought to exist in most industrial plants. In this case, process needs changed due to environmental regulations and change of location, but the system did not, leading to low overall system efficiency.

Wroblewski, R. G.; Preis, F.; Smith, R.

1997-04-01T23:59:59.000Z

454

Final Report Independent Verification Survey of the High Flux Beam Reactor, Building 802 Fan House Brookhaven National Laboratory Upton, New York  

Science Conference Proceedings (OSTI)

On May 9, 2011, ORISE conducted verification survey activities including scans, sampling, and the collection of smears of the remaining soils and off-gas pipe associated with the 802 Fan House within the HFBR (High Flux Beam Reactor) Complex at BNL. ORISE is of the opinion, based on independent scan and sample results obtained during verification activities at the HFBR 802 Fan House, that the FSS (final status survey) unit meets the applicable site cleanup objectives established for as left radiological conditions.

Evan Harpeneau

2011-06-24T23:59:59.000Z

455

GOTHIC Analysis of Containment Fan Cooler Unit (CFCU) Cooling Water Response Following a LOCA with Loss of Offsite Power  

Science Conference Proceedings (OSTI)

This report presents a simplified method to predict the thermal hydraulic status of a containment fan cooling system under a loss of coolant accident (LOCA) with loss of off-site power (LOOP). GOTHIC 5.0c, a general purpose thermal hydraulics computer program for analysis of nuclear power plants and confinements buildings, has been used for the calculation, and the results have been compared with those from RETRAN.

1997-12-23T23:59:59.000Z

456

NFRC Procedures for Applied Films  

NLE Websites -- All DOE Office Websites (Extended Search)

Applied Films Applied Films Last update: 12/10/2013 07:29 PM NFRC now has a procedure for adding applied films to substrates in Optics5 and importing those applied film constructions into WINDOW5 to be used in a whole product calculation. The information presented below is provided to help simulators with this process. Feel free to contact us at WINDOWHelp@lbl.gov with questions or comments. NFRC Applied Film Procedure Applied Film Procedures (approved by NFRC) (PDF file) Approved Applied Film List (IGDB 33.0) (PDF file) NFRC Laminate Procedure Training Powerpoint with Examples (This Powerpoint presentation was used in the NFRC web based training sessions in December 2006 and January 2007) PowerPoint Presentation (PPT file) PowerPoint Presentation (PDF file) Help and Troubleshooting

457

The Design Procedure Language Manual  

E-Print Network (OSTI)

This manual describes the Design Procedure Language (DPL) for LSI design. DPL creates and maintains a representation of a design in a hierarchically organized, object-oriented LISP data-base. Designing in DPL involves ...

Batali, John

1980-09-01T23:59:59.000Z

458

IES Calibration and Mapping Procedures  

Science Conference Proceedings (OSTI)

The procedures used in the Synoptic Ocean Prediction experiment for calibration of inverted echo sounder (IES) travel time ? data have led to substantially improved accuracy. In previous work, ? was converted to main thermocline depth ZT using ...

Karen L. Tracey; Stephan D. Howden; D. Randolph Watts

1997-12-01T23:59:59.000Z

459

Solar Thermal Test Facility experiment manual  

DOE Green Energy (OSTI)

Information is provided on administrative procedures, capabilities, and requirements of experimenters using the Solar Thermal Test Facility. (MHR)

Darsey, D. M.; Holmes, J. T.; Seamons, L. O.; Kuehl, D. J.; Davis, D. B.; Stomp, J. M.; Matthews, L. K.; Otts, J. V.

1977-10-01T23:59:59.000Z

460

Ultrabroadband optical parametric chirped-pulse amplifier using a fan-out periodically poled crystal with spectral spatial dispersion  

Science Conference Proceedings (OSTI)

Based on the full two-dimensional characteristics of the quasi-phase-matched fan-out periodically poled crystal, a scalable and engineerable scheme for ultrabroadband optical parametric chirped-pulse amplification is proposed, which can significantly broaden the gain bandwidth by the spatial separation of different frequency components of the signal pulse and manipulation of the distribution of the pump beam along the fan-out direction of the crystal. The theoretical analysis shows that the signal pulse can be amplified with minimal spectrum narrowing, and the initial spectrum can be broadened considerably if needed. Based on this scheme, using a fan-out periodically poled 5% mol MgO-doped congruent lithium niobate with a configuration of 5x0.5x5 mm{sup 3} and two pump beams, the 3.3-{mu}m middle-infrared ultrabroadband optical parametric chirped-pulse amplifier is designed. The numerical computation results confirm that the -3 dB gain bandwidth of this amplifier exceeds 320 nm and can be further broadened.

Chen Liezun; Wang Youwen [Key Laboratory for Micro/Nano Optoelectronic Devices of Ministry of Education, School of Information Science and Engineering, Hunan University, Changsha 410082 (China); Department of Physics and Electronic Information Science, Hengyang Normal University, Hengyang 421008 (China); Wen Shuangchun; Fan Dianyuan [Key Laboratory for Micro/Nano Optoelectronic Devices of Ministry of Education, School of Information Science and Engineering, Hunan University, Changsha 410082 (China); You Kaiming [Department of Physics and Electronic Information Science, Hengyang Normal University, Hengyang 421008 (China); Qian Liejia [Department of Optical Science and Engineering, Fudan University, Shanghai 200433 (China)

2010-10-15T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Impacts of Static Pressure Reset on VAV System Air Leakage, Fan Power and Thermal Energy - Part I: Theoretical Model and Simulation  

E-Print Network (OSTI)

As for a variable air volume (VAV) system, the air duct static pressure is a typical control variable maintained by modulating supply fan speed. The static pressure equals to the summation of the duct pressure loss downstream of the sensor to the terminal box and box inlet static pressure. Typically, the air duct static pressure is set as a constant set point based on the system design information and sensor location. However, under partial load conditions, the terminal box dampers have to be closed more since either required airflow is less than the design airflow which directly leads to much less pressure loss. Thus the static pressure set point should be reset lower in order to reduce fan power, avoid noise at terminal box dampers and box damper malfunction due to excessive pressure. Different static pressure reset schedules are reviewed and compared, considering the influence of outside air temperature on the building load, availability of the VAV box damper positions, the airflow ratio based static pressure reset has also applicable advantages over the existing constant static pressure set point and two typical reset methods. This paper present the theoretical models to express the impacts of static pressure reset on fan airflow, fan head, air leakage, fan power and thermal energy for both pressure independent and pressure dependent boxes. The impacts are also demonstrated using the parametric analysis and numerical results to show the benefits of the static pressure reset including reducing fan power, cooling energy and heating energy.

Liu, M.; Feng, J.; Wang, Z.; Wu, L.; Zheng, K.; Pang, W.

2007-01-01T23:59:59.000Z

462

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

E-Print Network (OSTI)

based methods of fault detection and diagnosis (FDD).Component-level FDD, which is the subject of the work

Xu, Peng; Haves, Philip

2002-01-01T23:59:59.000Z

463

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

E-Print Network (OSTI)

and diagnosis for cooling towers. ASHRAE Trans. , vol.107,of faults in the cooling tower circuit of a central chilled

Xu, Peng; Haves, Philip

2002-01-01T23:59:59.000Z

464

Test Automation Test Automation  

E-Print Network (OSTI)

Test Automation Test Automation Mohammad Mousavi Eindhoven University of Technology, The Netherlands Software Testing 2013 Mousavi: Test Automation #12;Test Automation Outline Test Automation Mousavi: Test Automation #12;Test Automation Why? Challenges of Manual Testing Test-case design: Choosing inputs

Mousavi, Mohammad

465

Procedure  

Science Conference Proceedings (OSTI)

... The recording drives used in this study include the Sony DRU-510A, 700A , 800A, Pioneer DVR-A09 , Plextor PX-716SA and NEC ND -2510A . ...

466

First semiannual report: Rocky Flats Small Wind Systems Test Center activities. Volume I. Description of the National Small Wind Systems Test Center  

DOE Green Energy (OSTI)

Information is presented concerning the Rocky Flats wind turbine test site; the philosophy of testing at Rocky Flats; test procedure development; atmospheric SWECS testing; SWECS component testing; data collection, handling, and analysis; reporting procedures; and future plans.

None

1978-09-28T23:59:59.000Z

467

Management of Hazardous Waste A Policy and Procedures Manual  

E-Print Network (OSTI)

the Toxicity Characteristic Leaching Procedure Test, or "TCLP") meets or exceeds these regulatory levels. For liquids, the TCLP result is approximately the same as the actual mass concentration. For solid state materials that contain any of the listed contaminants, the TCLP test needs to be conducted to determine

Cooley, Lynn

468

Photovoltaic module energy rating procedure. Final subcontract report  

DOE Green Energy (OSTI)

This document describes testing and computation procedures used to generate a photovoltaic Module Energy Rating (MER). The MER consists of 10 estimates of the amount of energy a single module of a particular type (make and model) will produce in one day. Module energy values are calculated for each of five different sets of weather conditions (defined by location and date) and two load types. Because reproduction of these exact testing conditions in the field or laboratory is not feasible, limited testing and modeling procedures and assumptions are specified.

Whitaker, C.M.; Newmiller, J.D. [Endecon Engineering (United States)

1998-01-01T23:59:59.000Z

469

Assembly and Field Testing of a Ground-Based Presence-of-Cloud Detector  

Science Conference Proceedings (OSTI)

A presence-of-cloud (POC) detector has been developed for use in remote locations. The principal components of the POC detector are a moisture-sensitive resistance grid, a heater, a fan, and housing with rain shielding. Field testing at a ...

D. O. Krovetz; M. A. Reiter; J. T. Sigmon; F. S. Gilliam

1988-08-01T23:59:59.000Z

470

Feasibility of an appliance energy testing and labeling program for Sri Lanka  

Science Conference Proceedings (OSTI)

A feasibility study evaluated the costs and benefits of establishing a program for testing, labeling and setting minimum efficiency standards for appliances and lighting in Sri Lanka. The feasibility study included: refrigerators, air-conditioners, flourescent lighting (ballasts & CFls), ceiling fans, motors, and televisions.

Biermayer, Peter; Busch, John; Hakim, Sajid; Turiel, Issac; du Pont, Peter; Stone, Chris

2000-04-01T23:59:59.000Z

471

Advanced Vehicle Testing Activity: Hydrogen Internal Combustion...  

NLE Websites -- All DOE Office Websites (Extended Search)

to someone by E-mail Share Advanced Vehicle Testing Activity: Hydrogen Internal Combustion Engine Vehicle Specifications and Test Procedures on Facebook Tweet about Advanced...

472

Improving Clinical Laboratory Testing through Harmonization ...  

Science Conference Proceedings (OSTI)

... involvement in harmonizing this category of clinical laboratory testing procedures. ... patients at risk from non-standardized laboratory test results and ...

2013-05-21T23:59:59.000Z

473

Federal Agency NEPA Implementing Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Agency NEPA Implementing Procedures Agency NEPA Implementing Procedures Note: Some Departments' agencies have their own NEPA implementing procedures. To access Department-wide NEPA implementing procedures, click on the name of the Federal Department. To access NEPA implementing procedures for Department's agencies, click on the provided links. Department/ Agency: Division: Link: Department of Agriculture Agricultural Research Service http://www.ecfr.gov/cgi- in/text- idx?c=ecfr&SID=47c103e07fd64e933c7f74c 4b3c4ac9a&rgn=div5&view=text&node=7:6. 1 2 1 8&id 7 Animal and Plant Health Inspection Service http://www.ecfr.gov/cgi-bin/text- idx?c=ecfr&SID=47c103e07fd64e933c7f74c 4b3c4ac9a&rgn=div5&view=text&node=7:5. 1.1.1.21&idno=7 Farm Service Agency http://www.ecfr.gov/cgi-bin/text-

474

A Semi-Automated Functional Test Data Analysis Tool  

E-Print Network (OSTI)

and the return fan speeds at their design values, turn offsupply and return fan speeds at their design values. If only

Xu, Peng; Haves, Philip; Kim, Moosung

2005-01-01T23:59:59.000Z

475

Surveillance Guide - OPS 9.16 Procedure Content and Use  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

PROCEDURE CONTENT AND USE PROCEDURE CONTENT AND USE 1.0 Objective The objective of this surveillance is to evaluate the effectiveness of the contractor's program for development and use of procedures. The Facility Representative reviews selected operating, surveillance or testing, and maintenance procedures and observes use of the procedures in the facility. This surveillance provides the basis for evaluating contractor performance and for establishing compliance with specific DOE requirements. 2.0 References 2.1 DOE 5480.19, Conduct of Operations Requirements for DOE Facilities 3.0 Requirements Implemented This surveillance is conducted to implement requirements of the Functions, Requirements and Authorities Manual, Section 20, Operations, FRAM #s 4253, 4258, and 4261. These requirements are

476

DOE Technical Standards Program: Procedures  

NLE Websites -- All DOE Office Websites (Extended Search)

Department of Energy Technical Standards Procedures Department of Energy Technical Standards Procedures Office of Nuclear Safety The following procedures should be used to write, revise, or maintain a DOE technical standard. They are also used to convert a DOE technical standard to a non-government standard or to form a topical committee. Table of Contents (TSPP-00) Program Overview and Responsibilities (TSPP-01) Initiating DOE Technical Standards (TSPP-02) Use of Voluntary Consensus Standards and Interaction with Standards Development Organizations (TSPP-03) Developing DOE Technical Standard (TSPP-04) Coordination of Technical Standards (TSPP-05) - Draft In Concurrence Resolution - TSPP-06-2009 is the currently approved TSPP that addresses coordination of DOE Technical Standards. Approving and Issuing DOE Technical Standards (TSPP-06)

477

Radiation control standards and procedures  

SciTech Connect

This manual contains the Radiation Control Standards'' and Radiation Control Procedures'' at Hanford Operations which have been established to provide the necessary control radiation exposures within Irradiation Processing Department. Provision is also made for including, in the form of Bulletins'', other radiological information of general interest to IPD personnel. The purpose of the standards is to establish firm radiological limits within which the Irradiation Processing Department will operate, and to outline our radiation control program in sufficient detail to insure uniform and consistent application throughout all IPD facilities. Radiation Control Procedures are intended to prescribe the best method of accomplishing an objective within the limitations of the Radiation Control Standards. A procedure may be changed at any time provided the suggested changes is generally agreeable to management involved, and is consistent with department policies and the Radiation Control Standards.

1956-12-14T23:59:59.000Z

478

Workshop on Test Procedures for Materials for Hydrogen ...  

Science Conference Proceedings (OSTI)

... Boulder, CO 80302-5821 (303) 442-5688. Gunbarrel Guest House 6901 Lookout Rd. ... Quality Inn & Suites 2020 Arapahoe Ave. ...

479

Development of Test Methods and Rating Procedures for ...  

Science Conference Proceedings (OSTI)

... membrane fuel cells (PEMFC) are the predominant type of fuel cell being considered for residential use, but solid oxide fuel cells (SOFC) are also ...

2002-03-01T23:59:59.000Z

480

Standard-C hydrogen monitoring system acceptance test procedure  

DOE Green Energy (OSTI)

The primary function of the standard-C hydrogen monitoring system (SHMS) is to monitor specifically for hydrogen in the waste tank atmosphere which may also contain (but not be limited to) unknown quantities of air, nitrous oxide, ammonia, water vapor, carbon dioxide, carbon monoxide, and other gaseous constituents. The SHMS will consist of hydrogen specific monitors, a grab sampler to collect samples for laboratory analysis, a gas chromatograph, and the gas sample collection system necessary to support the operation of the instrumentation. This system will be located in a cabinet placed at the tank of interest. The purpose of this document is to demonstrate that the SHMS is constructed as intended by design.

Schneider, T.C.

1994-09-02T23:59:59.000Z

Note: This page contains sample records for the topic "fans test procedure" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Standard-E hydrogen monitoring system shop acceptance test procedure  

DOE Green Energy (OSTI)

The purpose of this report is to document that the Standard-E Hydrogen Monitoring Systems (SHMS-E), fabricated by Mid-Columbia Engineering (MCE) for installation on the Waste Tank Farms in the Hanford 200 Areas, are constructed as intended by the design. The ATP performance will verify proper system fabrication.

Schneider, T.C.

1997-10-02T23:59:59.000Z

482

Solderability test system  

DOE Patents (OSTI)

A new test method to quantify capillary flow solderability on a printed wiring board surface finish. The test is based on solder flow from a pad onto narrow strips or lines. A test procedure and video image analysis technique were developed for conducting the test and evaluating the data. Feasibility tests revealed that the wetted distance was sensitive to the ratio of pad radius to line width (l/r), solder volume, and flux predry time.

Yost, Fred (Cedar Crest, NM); Hosking, Floyd M. (Albuquerque, NM); Jellison, James L. (Albuquerque, NM); Short, Bruce (Beverly, MA); Giversen, Terri (Beverly, MA); Reed, Jimmy R. (Austin, TX)

1998-01-01T23:59:59.000Z

483

Solderability test system  

DOE Patents (OSTI)

A new test method to quantify capillary flow solderability on a printed wiring board surface finish. The test is based on solder flow from a pad onto narrow strips or lines. A test procedure and video image analysis technique were developed for conducting the test and evaluating the data. Feasibility tests revealed that the wetted distance was sensitive to the ratio of pad radius to line width (l/r), solder volume, and flux predry time. 11 figs.

Yost, F.; Hosking, F.M.; Jellison, J.L.; Short, B.; Giversen, T.; Reed, J.R.

1998-10-27T23:59:59.000Z

484

Adaptive planning using megavoltage fan-beam CT for radiation therapy with testicular shielding  

Science Conference Proceedings (OSTI)

This study highlights the use of adaptive planning to accommodate testicular shielding in helical tomotherapy for malignancies of the proximal thigh. Two cases of young men with large soft tissue sarcomas of the proximal thigh are presented. After multidisciplinary evaluation, preoperative radiation therapy was recommended. Both patients were referred for sperm banking and lead shields were used to minimize testicular dose during radiation therapy. To minimize imaging artifacts, kilovoltage CT (kVCT) treatment planning was conducted without shielding. Generous hypothetical contours were generated on each 'planning scan' to estimate the location of the lead shield and generate a directionally blocked helical tomotherapy plan. To ensure the accuracy of each plan, megavoltage fan-beam CT (MVCT) scans were obtained at the first treatment and adaptive planning was performed to account for lead shield placement. Two important regions of interest in these cases were femurs and femoral heads. During adaptive planning for the first patient, it was observed that the virtual lead shield contour on kVCT planning images was significantly larger than the actual lead shield used for treatment. However, for the second patient, it was noted that the size of the virtual lead shield contoured on the kVCT image was significantly smaller than the actual shield size. Thus, new adaptive plans based on MVCT images were generated and used for treatment. The planning target volume was underdosed up to 2% and had higher maximum doses without adaptive planning. In conclusion, the treatment of the upper thigh, particularly in young men, presents several clinical challenges, including preservation of gonadal function. In such circumstances, adaptive planning using MVCT can ensure accurate dose delivery even in the presence of high-density testicular shields.

Yadav, Poonam [Department of Human Oncology, University of Wisconsin, Madison, Madison, WI (United States); Department of Medical Physics, University of Wisconsin, Madison, Madison, WI (United States); School of Advance Sciences, Vellore Institue of Technology University, Vellore, Tamil Nadu (India); Kozak, Kevin [Department of Human Oncology, University of Wisconsin, Madison, Madison, WI (United States); Tolakanahalli, Ranjini [Department of Human Oncology, University of Wisconsin, Madison, Madison, WI (United States); Department of Medical Physics, University of Wisconsin, Madison, Madison, WI (United States); Ramasubramanian, V. [School of Advance Sciences, Vellore Institue of Technology University, Vellore, Tamil Nadu (India); Paliwal, Bhudatt R. [Department of Human Oncology, University of Wisconsin, Madison, Madison, WI (United States); Department of Medical Physics, University of Wisconsin, Madison, Madison, WI (United States); University of Wisconsin, Riverview Cancer Centre, Wisconsin Rapids, WI (United States); Welsh, James S. [Department of Human Oncology, University of Wisconsin, Madison, Madison, WI (United States); Department of Medical Physics, University of Wisconsin, Madison, Madison, WI (United States); Rong, Yi, E-mail: rong@humonc.wisc.edu [Department of Human Oncology, University of Wisconsin, Madison, Madison, WI (United States); University of Wisconsin, Riverview Cancer Centre, Wisconsin Rapids, WI (United States)

2012-07-01T23:59:59.000Z

485

Handbook of Academic Requirements & Procedures  

E-Print Network (OSTI)

Handbook of Academic Requirements & Procedures for the Chemistry Graduate Program PLEASE NOTE: This version of the Handbook must be used by students who start during or after the Spring 2012 semester is a central activity. 1.2 Purpose and Content of the Handbook. A detailed account of the academic requirements

Kounaves, Samuel P.

486

Handbook of Academic Requirements & Procedures  

E-Print Network (OSTI)

Handbook of Academic Requirements & Procedures for the Chemistry Graduate Program PLEASE NOTE: This version of the Handbook can be used by students who started during or before the Fall 2011 semester activity. 1.2 Purpose and Content of the Handbook. A detailed account of the academic requirements

Kounaves, Samuel P.

487

FLORIDA STATE UNIVERSITY Procedures for  

E-Print Network (OSTI)

will be required that describes the purpose for the costs and the direct benefit to the proposed project's scopeFLORIDA STATE UNIVERSITY Procedures for Participant Support Costs Effective: May 15, 2006 Budgeting for Participant Costs Whenever Participant Support Costs are proposed in a budget, a detailed justification

Weston, Ken

488

Past DOE Technical Standards Program Procedures | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Information Center DOE Technical Standards Program DOE Technical Standards Procedures Past DOE Technical Standards Program Procedures Past DOE Technical Standards Program...

489

DNS Policies & Procedures | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

DNS Policies & Procedures DNS Policies & Procedures DNS Policy Every Federal agency must use only .gov, .mil, or Fed.us domains unless the agency head explicitly determines another...

490

EVMS Surveillance Standard Operating Procedure (ESSOP) | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reporting System (PARS II) INDEPENDENT COST REVIEW (ICR) and INDEPENDENT COST ESTIMATE (ICE) Standard Operating Procedures ICR-ICE Standard Operating Procedures (Update Sept 2013)...

491

Procedures and Instructions | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Access Training Records Management Processes Procedure for Conducting a Records Inventory (PDF) Procedure for Preparing a Records Inventory and Disposition Schedule (RIDS)...

492

External Independent Review (EIR) Standard Operating Procedure...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standard Operating Procedure (SOP) External Independent Review (EIR) Standard Operating Procedure (SOP) EIR SOP.pdf More Documents & Publications ICR-ICE Standard Operating...

493

Fire Tests of Amtrak Passenger Rail Vehicle Interiors  

Science Conference Proceedings (OSTI)

Page 1. Fire Tests of Amtrak Passenger ... Table 11. Test Procedures and Evaluation Criteria for Small- Scale Testing of Amtrak Furnishings..... ...

2004-04-02T23:59:59.000Z

494

Advanced Vehicle Testing Activity: U.S. Postal Service  

NLE Websites -- All DOE Office Websites (Extended Search)

Storage Testing Hydrogen Internal Combustion Engine Vehicles Full-Size Electric Vehicles Basics Specifications & Test Procedures Testing Reports Special Projects Neighborhood...

495

Surface Environmental Surveillance Procedures Manual  

SciTech Connect

Environmental surveillance data are used in assessing the impact of current and past site operations on human health and the environment, demonstrating compliance with applicable local, state, and federal environmental regulations, and verifying the adequacy of containment and effluent controls. SESP sampling schedules are reviewed, revised, and published each calendar year in the Hanford Site Environmental Surveillance Master Sampling Schedule. Environmental samples are collected by SESP staff in accordance with the approved sample collection procedures documented in this manual.

RW Hanf; TM Poston

2000-09-20T23:59:59.000Z

496

JOINT OFFICER MANAGEMENT PROGRAM PROCEDURES  

E-Print Network (OSTI)

implementation of the DOD Joint Officer Management (JOM) and Joint Qualification System (JQS) per references a through c. Reference a delegates the authority to the Chairman of the Joint Chiefs of Staff to establish and publish regulations and procedures to ensure compliance with the statutory and Department policy standards for DOD’s JOM program. 2. Cancellation. CJCSI 1330.02C, 24 February 2006, is cancelled. Required review of promotion selection board results policy guidance has been incorporated in this instruction.

References See Enclosure N; Responsibilities For

2008-01-01T23:59:59.000Z

497

CSP Policies & Procedures Process for Grade Appeals  

E-Print Network (OSTI)

CSP Policies & Procedures Process for Grade Appeals Grade Appeals ­ Generally speaking, once grades

Leistikow, Bruce N.

498

Impacts of Static Pressure Reset on VAV System Air Leakage, Fan Power and Thermal Energy - Part 2: Case Demonstration for a Typical Climate System  

E-Print Network (OSTI)

In Part 1 of this paper, the theoretical models, integrating the fan airflow, fan head, air leakage factors, are developed to analyze the impacts of the static pressure reset on both pressure dependent and pressure independent terminal boxes. In this part, a simulated air handling unit (AHU) system in Omaha NE is used to demonstrate the energy savings performance in one typical climate year. This AHU system has a static pressure reset system and two constant static pressure systems, one having pressure dependent terminal boxes and one having pressure independent terminal boxes. These simulated systems were compared mainly on the basis of fan power energy consumption and thermal energy consumption in totally a year. The example presents a good agreement with the theoretical model and simulation results. It was also shown that static pressure reset provides a promising and challenging way for the energy performance in VAV system.

Liu, M.; Zheng, K.; Wu, L.; Wang, Z.; Johnson, C.

2007-01-01T23:59:59.000Z

499

Microgrid Testing  

Science Conference Proceedings (OSTI)

With the publication of IEEE 1574.4 Guide for Design, Operation, and Integration of Distributed Resource Island Systems with Electric Power Systems, there is an increasing amount of attention on not only the design and operations of microgrids, but also on the proper operation and testing of these systems. This standard provides alternative approaches and good practices for the design, operation, and integration of microgrids. This includes the ability to separate from and reconnect to part of the utility grid while providing power to the islanded power system. This presentation addresses the industry need to develop standardized testing and evaluation procedures for microgrids in order to assure quality operation in the grid connected and islanded modes of operation.

Shirazi, M.; Kroposki, B.

2012-01-01T23:59:59.000Z

500

Society of Nuclear Medicine Procedure  

E-Print Network (OSTI)

The purpose of this guideline is to assist nuclear medicine practitioners in recommending, performing, interpreting, and reporting the results of lung scintigraphy for pulmonary embolism. II. Background Information and Definitions A. Aerosol Ventilation Scintigraphy A diagnostic imaging test that records the bronchopulmonary distribution of an inhaled radioactive aerosol within the lungs. B. Gas Ventilation Scintigraphy A diagnostic imaging test that records the pulmonary distribution of a radioactive gas during breathing maneuvers. C. Pulmonary Perfusion Scintigraphy A diagnostic imaging test that records the distribution

Guideline For Lung Scintigraphy

2004-01-01T23:59:59.000Z