Powered by Deep Web Technologies
Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Air-Side Energy Use Calculations for Four HVAC Systems: Dual Duct Constant Volume (DDCAV), Dual Duct Variable Volume (DDVAV), Constant Volume with Reheat (CAVRH), Variable Volume with Reheat (VAVRH), Four Pipe Fan Coil Unit (FC), Four Pipe Induction Unit (FI), and Single Zone (SZ) Systems, Revised June 2002  

E-Print Network [OSTI]

(CAVRH), and variable volume with reheat (VAVRH), four pipe fan coil unit (FC), four pipe induction unit (FI), and a single zone air conditioning system (SZ). These calculations are presented in spreadsheets that include a running commentary so...

Haberl, J. S.; Bou-Saada, T. E.; Saman, N. F.

2001-01-01T23:59:59.000Z

2

Supply fan energy use in pressurized underfloor air distribution systems  

E-Print Network [OSTI]

air-water devices like fan coil units and water source heatsuch as VAV boxes and fan coil units. One fairly typical

Webster, Tom P.E.; Bauman, Fred P.E.; Ring, Erik P.E.

2000-01-01T23:59:59.000Z

3

Feasibility Study: Ductless Hydronic Distribution Systems with Fan Coil Delivery  

SciTech Connect (OSTI)

The primary objectives of this study are to estimate potential energy savings relative to conventional ducted air distribution, and to identify equipment requirements, costs, and barriers with a focus on ductless hydronic delivery systems that utilize water-to-air terminal units in each zone. Results indicate that annual heating and cooling energy use can be reduced by up to 27% assuming replacement of the conventional 13 SEER heat pump and coil with a similarly rated air-to-water heat pump.

Springer, D.; Dakin, B.; Backman, C.

2012-07-01T23:59:59.000Z

4

Printed in the United States of America. Available from National Technical Information Service  

E-Print Network [OSTI]

Tests with Outdoor Fan Coil Unit ............. ................. 2 1.2.1 Space and water heating ....................... ... ........ .......................... 10 4. Outdoor Fan Coil Unit Tests ...... ......... ......... . ........................ . 11 4

Oak Ridge National Laboratory

5

Design and Operation of Fan-Coil Units in Using River Water as Chilled Water  

E-Print Network [OSTI]

in P. R. China. The concentrated A/C system utilizing natural cool resource of the river-water was built and put into service in 2000. The A/C system does not need any chiller, and the medium inlet-water provided to terminal equipment is just... The dew-point temperature of air at different dry-bulb temperature and relative humidity lt t ? t ? ? ? ?%? 20 22 24 26 28 40 6.09 7.85 9.62 11.39 13.17 50 9.31 11.13 12.96 14.80 16.63 60 12.02 13.90 15.78 17.66 19.55 70 14.38 16.30 18.22 20...

Jiang, A.; Chen, H.; Ma, W.; Zhu, H.

2006-01-01T23:59:59.000Z

6

Data Collection Methods for Assessing Adaptive Comfort in Mixed-Mode Buildings and Personal Comfort Systems  

E-Print Network [OSTI]

panel,  perimeter  fan  coil  unit).  However,  "direct"  controls  (perimeter  fan  coil  units,  supplemental  

Ackerly, Katie; Brager, Gail; Arens, Ed

2012-01-01T23:59:59.000Z

7

Risk Factors in Heating, Ventilating, and Air-Conditioning Systems for Occupant Symptoms in  

E-Print Network [OSTI]

cooling units (e.g. , fan coil units) in office buildingsinduction units, fan coil units, individual room packaged ACsystems, cooling tower, fan coil unit, and terminal units.

Mendell, M.J.; Lei-Gomez, Q.; Mirer, A.; Seppanen, O.; Brunner, G.

2007-01-01T23:59:59.000Z

8

Case Study: The Effective Use of an Extensive Logical rule Based Data Analytics Approach in Establishing Root Cause of Performance Issues in Widespread Deployments of Unitary Space Air Conditioning Units  

E-Print Network [OSTI]

Today a significant percentage of office spaces are air conditioned using widely deployed unitary systems, either Fan Coil Units (FCU) or Variable Air Volume (VAV) boxes, to achieve high degrees of air conditioned zonal control. However establishing...

Brady, N.

2013-01-01T23:59:59.000Z

9

DOE-1 USERS GUIDE  

E-Print Network [OSTI]

default) is used for Fan Coil units, Unit Ventilators andFan Coil (TPFC and FPFC). Fan Coil Units are either 4-pipeand residential units, fan coil units are often supplied

Authors, Various

2011-01-01T23:59:59.000Z

10

Sustainable Building in China - A Green Leap Forward?  

E-Print Network [OSTI]

air-handling units, and fan coil units. Sincetemperature is high, the fan-coil units just condition the

Diamond, Richard C.

2014-01-01T23:59:59.000Z

11

DOE-1 USERS GUIDE  

E-Print Network [OSTI]

Fan Coil (TPFC and FPFC). Fan Coil Units are either 4-pipeand residential units, fan coil units are often suppliedunits are very similar to fan coil units in concept, and can

Authors, Various

2011-01-01T23:59:59.000Z

12

CBE UFAD cost analysis tool: Life cycle cost model, issues and assumptions  

E-Print Network [OSTI]

diffusers, underfloor fan coil units (FCU), etc. that arepurposes: VAV boxes and Fan Coil Units (FCU). Furthermore,

Webster, Tom; Benedek, Corinne; Bauman, Fred

2008-01-01T23:59:59.000Z

13

Energy performance of air distribution systems part II: room air stratification full scale testing  

E-Print Network [OSTI]

and are connected to a fan coil unit by flexible ductwork asvariable air volume fan coil units typically used in

Webster, Tom; Lukaschek, Wolfgang; Dickeroff, Darryl; Bauman, Fred

2007-01-01T23:59:59.000Z

14

Assessment and Improvements of the CBE Underfloor Air Distribution (UFAD) Cooling Load Design Tool  

E-Print Network [OSTI]

diffusers and underfloor fan coil units. .. 53 Figure 33 Thediffusers and underfloor fan coil units. Table 14 shows the

Chen, Bin

2014-01-01T23:59:59.000Z

15

Cooling load design tool for UFAD systems.  

E-Print Network [OSTI]

ratio of time between Fan Coil Units Perimeter Zone Linearand underfloor fan coil units. cooling contribution of

Bauman, Fred; Schiavon, Stefano; Webster, Tom; Lee, Kwang Ho

2010-01-01T23:59:59.000Z

16

Automatic Continuous Commissioning of Measurement Instruments in Air Handling Units  

E-Print Network [OSTI]

by International Energy Agency (IEA) and widely studied in the research projects of Annex 40[2] and Annex 47[3]. An open publication [4] found a media payback period of 4.8 years for commissioning of new buildings in United States. Additionally, commissioning... w Chilled water fanr Return air fan val Valve rtn Return air exh Exhaust air fans Supply air fan coil Cooling coil REFERENCES [1] Buildings Rese Lawrence Be [2] IEA ECBCS...

Xiao, F.; Wang, S.

2006-01-01T23:59:59.000Z

17

2.1E Supplement  

E-Print Network [OSTI]

duct air handlers and fan coil units. This curve describeszonal unit (e.g. , fan coil unit, water source heat pump,zone exhausts, and zonal units such as fan coils and package

Winkelmann, F.C.

2010-01-01T23:59:59.000Z

18

Radiant cooling research scoping study  

E-Print Network [OSTI]

ventilation air, fan-coil units, and added lightweightventilation air, fan-coil units, induction units, chilled-conditioned using a fan-coil unit or other non-radiant

Moore, Timothy; Bauman, Fred; Huizenga, Charlie

2006-01-01T23:59:59.000Z

19

Comparison of Building Energy Modeling Programs: HVAC Systems  

E-Print Network [OSTI]

Four Pipe Fan Coil; Four Pipe Induction Unit; Heating andTwo Pipe Fan Coil; Two Pipe Induction Unit; Unit Heater;units (AHUs) – four CAV systems, four VAV systems, and one fan coil

Zhou, Xin

2014-01-01T23:59:59.000Z

20

Energy efficient data centers  

E-Print Network [OSTI]

Center 6.2 utilized fan coil units, rather than computerEfficiency kW/ton Fan Coil Unit Design Efficiency CFM/kWCenter 6.2 utilized fan coil units, rather than computer

Tschudi, William; Xu, Tengfang; Sartor, Dale; Koomey, Jon; Nordman, Bruce; Sezgen, Osman

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Air leakage test report: EPA region 8 headquarters, Denver, CO  

E-Print Network [OSTI]

of 21 underfloor fan-coil units, which are ducted to aductwork by underfloor fan coil units and have no dampers toiwc and each of the 21 fan coil units has capacity of 1200

Bauman, Fred; Webster, Tom; Dickerhoff, Darryl

2008-01-01T23:59:59.000Z

22

Localized Thermal Distribution for Office Buildings; Final Report - Phase III  

E-Print Network [OSTI]

level is local (zonal) fan coil units served by variableby the T A M s and fan coil units, and has a rate of energyfan and the local fan coil units. The TAMs were sized to

1994-01-01T23:59:59.000Z

23

Lessons learned in modeling Underfloor Air Distribution system  

E-Print Network [OSTI]

UFAD variable speed fan coil units are not straightforwarda variable speed fan coil unit model object was developed inand a constant volume fan coil unit, used only for heating.

Lee, Kwang Ho; Schiavon, Stefano; Webster, Tom; Bauman, Fred; Feng, Jingjuan; Hoyt, Tyler

2011-01-01T23:59:59.000Z

24

Using ductwork to improve supply plenum temperature distribution in underfloor air distribution (UFAD) system  

E-Print Network [OSTI]

connected with ducts to fan coil units to minimize the heatthe interior zone, plus two fan coil units. Figure 8-2 showswas used for this work. FAN COIL UNITS PERIMETER Figure 8-3

Pasut, Wilmer

2011-01-01T23:59:59.000Z

25

Advanced Integrated Systems Technology Development  

E-Print Network [OSTI]

by the fact that the fan coil units were undersized for thethe 11 th floor but the fan coil units were still running attype – York, variable speed fan coil unit, Tate. ? Room air

2013-01-01T23:59:59.000Z

26

Advanced Design and Commissioning Tools for Energy-Efficient Building Technologies  

E-Print Network [OSTI]

the intakes of the fan coil units, if feasible. See furtherductwork from underfloor fan coil units), even when the sillthe intakes of the fan coil units can help minimize leakage

Bauman, Fred; Webster, Tom; Zhang, Hui; Arens, Ed

2012-01-01T23:59:59.000Z

27

Task/ambient conditioning systems: Engineering and application guidelines  

E-Print Network [OSTI]

or water-based fan coil units) at the supply outlets duringplant and not with local fan coil units. Although they arethe space. 3. Water-based fan coil units (or other means as

Bauman, Fred S P.E.; Arens, Edward A Ph.D.

1996-01-01T23:59:59.000Z

28

Healthcare Energy Efficiency Research and Development  

E-Print Network [OSTI]

loads and four pipe fan coil units in the 1968 building. Nobuilding has four pipe fan coil units and constant volumefans. Calculate use for fan coil units and small exhaust

Lanzisera,, Judy Lai, Steven M.

2012-01-01T23:59:59.000Z

29

Energy saving strategies with personalized ventilation in tropics  

E-Print Network [OSTI]

is extracted by the fan coil units from the room in 1 year (a two-pipe overhead fan coil unit, is used to keep the roomto the room through the fan coil unit. There is no heating

Schiavon, Stefano; Melikov, Arsen; Chandra Sekhar, Chandra Sekhar

2010-01-01T23:59:59.000Z

30

Energy-saving strategies with personalized ventilation in cold climates  

E-Print Network [OSTI]

were modelled. Four-pipe fan coil units were used to controlthat is extracted by the fan coil units from the room in oneis supplied by the fan coil units to the room in one year (

Schiavon, Stefano; Melikov, Arsen

2009-01-01T23:59:59.000Z

31

Monitoring the Energy-Use Effects of Cool Roofs on California Commercial Buildings  

E-Print Network [OSTI]

Volume Forced Air System Fan Coil Unit (New) Economizer DuctAir System Capacity Fan Coil Unit Economizer Duct Leakagewall mounted condensing units and fan coils in the ceiling

Akbari, Hashem; Levinson, Ronnen; Konopaki, Steve; Rainer, Leo

2004-01-01T23:59:59.000Z

32

California department of education HQ block 225: California's valedictorian  

E-Print Network [OSTI]

on underfloor fan-coil units. The ease of repositioningUnderfloor variable speed fan-coil units at the buildingvariable speed fan-coil units are ducted to linear bar

Bauman, Fred; Webster, Tom; Dickerhoff, Darryl J; Fentress, Curtis; Popowski, Matt

2009-01-01T23:59:59.000Z

33

CBE EnergyPlus Modeling Methods for UFAD Systems  

E-Print Network [OSTI]

when connected to a fan coil unit (as Titus and other linearof the diffuser as supplied by a fan coil unit for Titusdiffusers and fan coil unit for the Walnut based systems.

Webster, Tom; Bauman, Fred; Lee, Kwang Ho; Schiavon, Stefano; Daly, Alan; Hoyt, Tyler

2012-01-01T23:59:59.000Z

34

CBE EnergyPlus modeling methods for UFAD systems  

E-Print Network [OSTI]

when connected to a fan coil unit (as Titus and other linearof the diffuser as supplied by a fan coil unit for Titusdiffusers and fan coil unit for the Walnut based systems.

Webster, T.; Bauman, F.; Lee, K.; Schiavon, S.; Daly, A.; Hoyt, T.

2013-01-01T23:59:59.000Z

35

Occupant Response to Window Control Signaling Systems  

E-Print Network [OSTI]

Air Conditioning   Fan coil units, variable refrigerant active cooling via fan coil units and radiant panels, system to perimeter fan coil units, and “open”  mode for 

Ackerly, Katherine

2012-01-01T23:59:59.000Z

36

A post-occupancy monitored evaluation of the dimmable lighting, automated shading, and underfloor air distribution system in The New York Times Building  

E-Print Network [OSTI]

underfloor variable speed fan-coil units) that serves as afor the perimeter fan-coil units (typically prescribed bycooling setpoints in the fan-coil unit controllers instead

Lee, Eleanor S.

2014-01-01T23:59:59.000Z

37

Demonstration of Rack-Mounted Computer Equipment Cooling Solutions  

E-Print Network [OSTI]

the ceiling-mounted fan-coil unit return- water temperatureto supply no cooling. The fan-coil unit was controlled by atemperature) when the fan-coil unit control calls for no

Coles, Henry

2014-01-01T23:59:59.000Z

38

2.1E BDL Summary  

E-Print Network [OSTI]

Two Pipe Fan Coil Two Pipe Induction Unit Heater ClassroomFour Pipe Fan Coil System Two Pipe Induction Unit SystemCooling Unit (User—Defined) Four Pipe Fan Coil Panel Heating

Winkelmann, F.C.

2010-01-01T23:59:59.000Z

39

A Post-Occupancy Monitored Evaluation of the Dimmable Lighting, Automated Shading, and Underfloor Air Distribution System in The New York Times Building  

E-Print Network [OSTI]

underfloor variable speed fan-coil units) that serves as afor the perimeter fan-coil units (typically prescribed bycooling setpoints in the fan-coil unit controllers instead

2013-01-01T23:59:59.000Z

40

2.1E Supplement  

E-Print Network [OSTI]

duct air handlers and fan coil units. This curve describeszonal unit (e.g. , fan coil unit, water source heat pump,

Winkelmann, F.C.

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Development of guidelines for Modeling Underfloor Air Distribution (UFAD) Systems in EnergyPlus, eQUEST, and EnergyPro for use in California non-residential Building Energy Efficiency Standards  

E-Print Network [OSTI]

None  cubic  None  Fan coil Terminal units  Terminal unit unit airflow which is more consistent with how fan coils

2011-01-01T23:59:59.000Z

42

Trends in design and operations of UFAD buildings  

E-Print Network [OSTI]

is a low usage of fan coil units (FCU), contrary to ours suites were served by a fan coil unit. This building was

Hogan, Mark; Webster, Tom; Bauman, Fred

2005-01-01T23:59:59.000Z

43

 Underfloor air distribution (UFAD) cost study: analysis of first cost tradeoffs in UFAD systems  

E-Print Network [OSTI]

is served by VAV fan coil units (FCU) with variable speedwith regard to terminal fan coil unit costs. Since the model

Webster, Tom; Benedek, Corinne; Bauman, Fred

2006-01-01T23:59:59.000Z

44

Introduction to Commercial Building Control Strategies and Techniques for Demand Response -- Appendices  

E-Print Network [OSTI]

peak period, and 2) reduce fan coil units' capacity on the78.5°F Reduce perimeter fan coil units to 30% capacity from

Motegi, N.

2011-01-01T23:59:59.000Z

45

Simulation of energy performance of underfloor air distribution (UFAD) systems  

E-Print Network [OSTI]

system represents a fan coil unit (FCU) system, consistingEnergy use intensity EUI Fan coil unit F CU HVAC electricityarea Fan powered terminal unit (with heating coil) used for

2009-01-01T23:59:59.000Z

46

INFLUENCE OF SUPPLY AIR TEMPERATURE ON UNDERFLOOR AIR DISTRIBUTION (UFAD) SYSTEM ENERGY PERFORMANCE  

E-Print Network [OSTI]

this study, perimeter fan coil unit (FCU) energy also addsvariable speed series fan coil unit. The FCU shuts off whenunit including an economizer, chilled water cooling coil, and supply fan.

2012-01-01T23:59:59.000Z

47

 Underfloor air distribution (UFAD) cost study: analysis of first cost tradeoffs in UFAD systems  

E-Print Network [OSTI]

is served by VAV fan coil units (FCU) with variable speedwith regard to terminal fan coil unit costs. Since the modelfan powered boxes with hot water reheat coils. Because it is a constant volume unit,

Webster, Tom; Benedek, Corinne; Bauman, Fred

2006-01-01T23:59:59.000Z

48

Modeling of ECM Controlled Series Fan-powered VAV Terminal Units  

E-Print Network [OSTI]

Semi-empirical models for series fan-powered variable air volume terminal units (FPTUs) were developed based on models of the primary, plenum, fan airflow and the fan power consumption. The experimental setups and test procedures were developed...

Yin, Peng

2011-10-21T23:59:59.000Z

49

Comfort control for short-term occupancy  

E-Print Network [OSTI]

to a thermostat-controlled fan-coil unit i n each room. TheThe t y p i c a l fan-coil and w a l l units are i n this

Fountain, M.; Brager, G. S.; Arens, Edward A; Bauman, Fred; Benton, C.

1994-01-01T23:59:59.000Z

50

Summer Projects 2013 Major Capital Projects  

E-Print Network [OSTI]

;Hanszen College ­ New Wing Fan Coil Unit Replacement #12;#12;Mudd Lab High Voltage Automatic Transfer

Alvarez, Pedro J.

51

Performance of ECM controlled VAV fan powered terminal units  

E-Print Network [OSTI]

signal from low pass filter h Enthalpy HVAC Heating, Ventilation, & Air Conditioning IRMS RMS value of current (amps) ? ? m mass flow rate Piav Inlet air velocity differential pressure Pdown Downstream static pressure Punit... Static pressure inside terminal unit Pup Upstream static pressure Powerfan Power consumption of terminal unit fan PF Power Factor PSC Permanent Split Capacitor ? ? Q Change in heat input per unit time Qfan Amount of airflow through...

Cramlet, Andrew Charles

2009-05-15T23:59:59.000Z

52

INFLUENCE OF DESIGN AND OPERATING CONDITIONS ON UNDERFLOOR AIR DISTRIBUTION (UFAD) SYSTEM PERFORMANCE  

E-Print Network [OSTI]

zones. Variable speed fan coil units (VSFCU) provide air tounit (AHU) including an airside economizer, a chilled water cooling coil, and a relief fan.

2012-01-01T23:59:59.000Z

53

Thermal decay in underfloor air distribution (UFAD) systems: Fundamentals and influence on system performance  

E-Print Network [OSTI]

zones. Variable-speed fan coil units ( FCU) supply air tounit (AHU) including an economizer, chilled water cooling coil, hot water heating coil and supply fan.

Lee, Kwang Ho; Schiavon, Stefano; Bauman, Fred; Webster, Tom

2012-01-01T23:59:59.000Z

54

Simplified calculation method for design cooling loads in underfloor air distribution (UFAD) systems  

E-Print Network [OSTI]

the outlet side of fan coil units (FCU) served by variableunit (AHU) including a return air economizer, chilled water cooling coil, hot water heating coil and supply fan.

Schiavon, Stefano; Lee, Kwang Ho; Bauman, Fred; Webster, Tom

2010-01-01T23:59:59.000Z

55

Modeling of Electronically Commutated Motor Controlled Fan-powered Terminal Units  

E-Print Network [OSTI]

Feet Per Minute ECM Electronically Commutated Motor FPTU Fan Powered Terminal Unit Pdown Downstream Static Pressure PF Power Factor Pup Upstream Static Pressure SCR Silicon Controlled Rectifier THD Total Harmonic Distortion VAV Variable Air... parallel unit pressurizes the FPTU causing some of the primary air to leak out of the unit. Another difference between them is that series terminal units allow the primary air system to operate at a lower static pressure because the terminal unit fan...

Edmondson, Jacob Lee

2011-02-22T23:59:59.000Z

56

Final Project Report: Self-Correcting Controls for VAV System Faults Filter/Fan/Coil and VAV Box Sections  

SciTech Connect (OSTI)

This report addresses original research by the Pacific Northwest National Laboratory for the California Institute for Energy and Environment on self-correcting controls for variable-air-volume (VAV) heating, ventilating and air-conditioning systems and focuses specifically on air handling and VAV box components of the air side of the system. A complete set of faults for these components was compiled and a fault mode analysis performed to understand the detectable symptoms of the faults and the chain of causation. A set of 26 algorithms was developed to facilitate the automatic correction of these faults in typical commercial VAV systems. These algorithms include training tests that are used during commissioning to develop models of normal system operation, passive diagnostics used to detect the symptoms of faults, proactive diagnostics used to diagnose the cause of a fault, and finally fault correction algorithms. Ten of the twenty six algorithms were implemented in a prototype software package that interfaces with a test bed facility at PNNL's Richland, WA, laboratory. Measurement bias faults were instigated in the supply-air temperature sensor and the supply-air flow meter to test the algorithms developed. The algorithms as implemented in the laboratory software correctly detected, diagnosed and corrected these faults. Finally, an economic and impact assessment was performed for the State of California for deployment of self-correcting controls. Assuming 15% HVAC energy savings and a modeled deployment profile, 3.1-5.8 TBu of energy savings are possible by year 15.

Brambley, Michael R.; Fernandez, Nicholas; Wang, Weimin; Cort, Katherine A.; Cho, Heejin; Ngo, Hung; Goddard, James K.

2011-05-01T23:59:59.000Z

57

Performance of VAV Fan Powered Terminal Units: Experimental Results and Models for Parallel Units  

E-Print Network [OSTI]

consists of a central air handling unit (AHU), where air is cooled by cooling coils (Wendes 1994). This air, referred to as primary air, is sent through a single-duct supply system to VAV terminal units by the supply fan. Each terminal unit is ducted to air... surprise that the flow regressed well with the square root of the pressure differential across the terminal unit at a given damper setting and showed no dependence on SCR. The construction quality of these terminal units could be an item of concern...

Furr, J.; O'Neal, D.; Davis, M.; Bryant, J.; Cramlet, A.

58

Laboratories for the 21st Century: Best Practices; Energy Recovery...  

Broader source: Energy.gov (indexed) [DOE]

rooms and electrical transformer rooms) using local terminal cooling units like chilled beams or fan coil units and transfers it through a chiller to spaces in the building...

59

Construction News Report February 2011  

E-Print Network [OSTI]

control wire on the 1st floor. · Piped fan coil unit risers at the south stairwell. · Started north stair

60

EECBG Success Story: Energy Savings, Improved Comfort for West...  

Broader source: Energy.gov (indexed) [DOE]

HVAC system. | Photo courtesy of Deborah Hammond The Dunn Building in Martinsburg, West Virginia replaced its HVAC system with a new chiller system fan coil units and...

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Supply Fan Control for Constant Air Volume Air Handling Units  

E-Print Network [OSTI]

there is fixed VFD speed, as shown in Table 1 and Figure 11. On the other hand, the energy consumption is 3,896,493 Btu/hr when there is dynamic VFD speed. The thermal energy consumption of dynamic VFD speed is less than that of the fixed VFD speed by 44... %. Therefore, when the supply fan speed control is optimized, thermal energy can be reduced. Table 1. Comparison data of thermal energy consumption Floor Fixed VFD speed (Btu/hr) Dynamic VFD speed (Btu/hr) Energy saving (%) PLF 784,891 502,611 36...

Cho, Y.; Wang, G.; Liu, M.

2007-01-01T23:59:59.000Z

62

Laboratory Evaluation of Fan-filter Units' Aerodynamic and Energy Performance  

E-Print Network [OSTI]

Laboratory Evaluation of Fan-filter Units' Aerodynamic and Energy Performance Tengfang Xu, Lawrence The paper discusses the benefits of having a consistent testing method to characterize aerodynamic applications. Optimizing aerodynamic performance in air recirculation systems appears to be one of useful

63

Development of models for series and parallel fan variable air volume terminal units  

E-Print Network [OSTI]

for the series and parallel units, with coefficients varying by size and manufacturer. Statistical modeling utilized SAS software (2002). Fan power and airflow data were collected at downstream static pressures over a range from 0.1 to 0.5 in. w.g. (25 to 125 Pa...

Furr, James C., Jr

2007-09-17T23:59:59.000Z

64

Performance of VAV Parallel Fan Powered Terminal Units: Experimental Results and Models  

E-Print Network [OSTI]

with the guidelines for testing fan powered terminal units as specified in ANSI/ASHRAE Standard 130, (1996). Two blowers, controlled by variable speed drives (VSDs), were used to adjust the static pressures upstream and down- stream of the terminal units... Sensor Pressure 0-2 in. w.g. (0-0.5 kPa) Table 5. Test Variable Levels Independent Variable Number of Levels Values Upstream Static Pressure 3 varied from 0.3 to 2 in. w.g. (75 to 498 Pa) Downstream Static Pressure 3 0.1, 0.25, 0.5 in. w.g (25, 62, 125...

Furr, J.; O'Neal, D.; Davis, M.; Bryant, J.; Cramlet, A.

65

EXPERIMENTAL TEST FACILITY FOR EVALUATION OF CONTROLS AND CONTROL STRATEGIES  

E-Print Network [OSTI]

air channel with fan coil, an auxiliary heat source, and associated pumpsair channel with fan coil, an auxiliary heat source, and associated pumps

Warren, Mashuri L.

2013-01-01T23:59:59.000Z

66

Laboratory evaluation of fan/filter units' aerodynamic and energy performance  

SciTech Connect (OSTI)

The paper discusses the benefits of having a consistent testing method to characterize aerodynamic and energy performance of FFUs. It presents evaluation methods of laboratory-measured performance of ten relatively new, 1220 mm x 610 mm (or 4 ft x 2 ft) fan-filter units (FFUs), and includes results of a set of relevant metrics such as energy performance indices (EPI) based upon the sample FFUs tested. This paper concludes that there are variations in FFUs' performance, and that using a consistent testing and evaluation method can generate compatible and comparable FFU performance information. The paper also suggests that benefits and opportunities exist for our method of testing FFU energy performance to be integrated in future recommended practices.

Xu, Tengfang; Jeng, Ming-Shan

2004-07-27T23:59:59.000Z

67

Toward green systems for cleanrooms: Energy efficient fan-filter units  

SciTech Connect (OSTI)

The paper presents results of laboratory-measured performance of fan-filter units (FFUs) used for cleanrooms. A total of twenty FFUs collected from the market were tested, including thirteen 1220 mm x 610 mm (or 4 ft x 2 ft) units and seven 1220 mm x 1220 mm (or 4 ft x 4 ft) units. The paper concludes that there are wide variations in FFUs energy performance, and that there are opportunities in improving energy efficiency and lowering operating costs of FFUs. Furthermore, the paper suggests the benefits of having a uniform method for testing and reporting FFU performance. Such a testing method and recommended practice guideline is under development, with heavy input from FFU suppliers, users, and independent institutions that include Lawrence Berkeley National Laboratory (LBNL), Industrial Technology Research Institute (ITRI), and Institute of Environmental Sciences and Technology (IEST). An integrated approach with the participation from designers, suppliers, users, and utility companies can help to identify energy-efficient FFUs that are required for many cleanroom applications.

Jeng, Ming-Shan; Xu, Tengfang; Lan, Chao-Ho

2004-07-12T23:59:59.000Z

68

Summary Report: Control Strategies for Mixed-Mode Buildings  

E-Print Network [OSTI]

air conditioning systems include fan coil units (FCUs) and water-source heat pumpSource Heat Pump; radiant slab heating and cooling; low flow A/C dehumidifies air;

Brager, Gail; Borgeson, Sam; Lee, Yoonsu

2007-01-01T23:59:59.000Z

69

Integrated Temperature and Humidity Control: A Unique Approach  

E-Print Network [OSTI]

as in Singapore. The results presented herein are from one of these sites, consisting of two adjacent unoccupied guest rooms in a hotel, each equipped with chilled- water fan coil units. The two, virtually identical adja- cent rooms were selected primarily... for comparing the operation and performance of the ITHC with that of a dry-bulb temperature controller (DBTC) under the exact same conditions (solar, outdoor temperature and humidity, internal loads, etc.). To obtain com- parative results, the fan coil unit...

Shah, D. J.

2000-01-01T23:59:59.000Z

70

Monthly Indices: A Procedure for Energy Use Display Creating Monthly Indices for Comparing the Energy Consumption of Buildings  

E-Print Network [OSTI]

by individual hydronic fan coil units. The first floor is heated/cooled by a hydronic air handler, and there are single air handlers on floors two through four to supply outside air to each floor. The two story Unit B contains the auditorium, choir Energy... operate whenever the hydronic air handler does not provide cooling, in order to prevent humidity problems. Unit C is a single story building which contains the cafeteria and kitchen. It is heated/cooled by hydronic fan-coil units (six in the cafeteria, two...

Landman, D. S.; Haberl, J. S.

1996-01-01T23:59:59.000Z

71

Understanding Manufacturing Energy Use Through Statistical Analysis  

E-Print Network [OSTI]

. The energy required to chill this glycol should be dependent on outdoor air temperature. The rest of the chilled glycol is sent to fan-coil units that recirculate plant air near heat-generating equipment. The energy required to chill this glycol is much... less dependent on outdoor air temperature. Thus, comparing the two breakdowns suggests that about (13% - 10%) / 13% = 23% of chiller electricity use is devoted to the fan coil units and the balance to the make-up air units. The biggest...

Kissock, J. K.; Seryak, J.

2004-01-01T23:59:59.000Z

72

Case study of Chilled Water Loop Low Delta-T Fault Diagnosis  

E-Print Network [OSTI]

points for air handlers and fan coil units 2. Valve & Control Malfunctions 3. Chiller plant / cooling coil design parameter mismatch ? Winter:5.5°F – 6.5°F (3.06°C-3.61°C) Improvement ? Summer:4°F (2.22°C) Improvement 30% Energy Systems Laboratory p. 16... Proceedings of the 14th International Conference for Enhanced Building Operations, Beijing, China, September 14-17, 2014 Roots Causes of Low ?T Energy Systems Laboratory p. 14 ? Sub-optimal control strategies and set points for air handlers and fan coil...

Wang, L.; Meline, K.; Watt, J.

2014-01-01T23:59:59.000Z

73

Application of the Continuous Commissioning Process at a K-12 School Distrcit Located in Cental Texas  

E-Print Network [OSTI]

-10-09 Proceedings of the 13th International Conference for Enhanced Building Operations, Montreal, Quebec, October 8-11, 2013 distributed HVAC systems. Air-side systems generally include various types of air handling units (AHUs), fan coil units (FCUs), terminal...

Shah, M.; Sun, Y.; Lander, W.; Yagua, C.; Watt, J.; Oh, S.; Claridge, D.

2013-01-01T23:59:59.000Z

74

Submarine fan lobes  

SciTech Connect (OSTI)

Submarine fan lobes constitute major hydrocarbon reservoirs throughout the world. Therefore, a clear understanding of their geometry and facies relationships is critical for exploring and exploiting these sandstone bodies effectively. However, a multitude of submarine fan lobe terminologies (e.g., depositional lobe, suprafan lobe, fan lobe, erosional lobe, channelized lobe, ponded lobe, leveed-valley lobe, type I lobe, and type II lobe) advocating widely different meanings, has flourished in the sedimentologic literature. A critical evaluation of this problem has resulted in the following suggestions: (1) lobes are considered to be turbidite sand bodies that develop at the mouths of channels in deep-sea fan environments; (2) the term depositional lobe should be restricted to lower-fan deposits of fans that exhibit facies C and thickening-upward cycles; (3) the term suprafan lobe refers to middle-fan deposits of certain small, sand-rich, modern fans that exhibit a convex-upward depositional bulge in seismic reflection profiles; (4) the terms fan lobe, erosional lobe, channelized lobe, ponded lobe, and leveed-valley lobe do not represent true channel-mouth deposits and therefore are potentially confusing; (5) lower-fan sheet sands of large modern fans may not be equivalent to depositional lobes of ancient fans; and (6) popular fan models with lobes are not always applicable because they disregard large modern fans without lobes (e.g., Mississippi fan).

Shanmugam, G.

1989-03-01T23:59:59.000Z

75

Effect of a Radiant Panel Cooling System on Indoor Air Quality of a Conditioned Space  

E-Print Network [OSTI]

This paper discusses the effect of a radiant cooling panel system on an indoor air quality (IAQ) of a conditioned space. In this study, ceiling radiant cooling panel, mechanical ventilation with fan coil unit (FCU) and 100% fresh air are used...

Mohamed, E.; Abdalla, K. N.

2010-01-01T23:59:59.000Z

76

Radiant Barrier Performance during the Heating Season  

E-Print Network [OSTI]

with identical Fan Coil Units (FCU), digital thermostats and electric resistance heaters. Both heaters were identical and rated at 4100 Btu/hr. These heaters were directly connected to the thermostats and to watt-hour counters and watt-meters. The watt...

Medina, M. A.; O'Neal, D. L.; Turner, W. D.

77

Effects of Radiant Barrier Systems on Ventilated Attics in a Hot and Humid Climate  

E-Print Network [OSTI]

. Both houses were equipped with identical Fan Coil Units (FCU), digital thermostats and water pumps. A chilled water circuit was designed to supply both houses with a cold water/glycol solution (60/40) at approximately 40 of. The solution was kept...

Medina, M. A.; O'Neal, D. L.; Turner, W. D.

78

Aeroseal, LLC a JMD, Inc Company  

E-Print Network [OSTI]

. Remove foam blocks isolating furnace, AC coil or fan coil. 6. Verify intentional outdoor air intakes-Sealing Leakage Test 1. Turn off the HVAC unit to be tested. 2. Set-up the Blower Door testing system. 3. Open any resistance between the supply and return sides (e.g. a dirty or blocked coil). 7. If the Aeroseal machine

79

A FULL SCALE ROOM FOR THE EXPERIMENTAL STUDY OF INTERIOR BUILDING CONVECTIVE HEAT TRANSFER  

E-Print Network [OSTI]

air flow measurement. A water source heat pump provided chilled water to a fan-coil unit which in turn on volumetric air flow measurement and an overall room heat balance. Analysis was directed at results fromA FULL SCALE ROOM FOR THE EXPERIMENTAL STUDY OF INTERIOR BUILDING CONVECTIVE HEAT TRANSFER: DESIGN

80

Sub-metering to Electricity Use in Large-scale Commercial Buildings  

E-Print Network [OSTI]

;?#0;? Practice??Project example #0;?#0;? Use of data??Analysis Software Sub-metering and statistics to electricity use in commercial buildings 8 Method of sub-metering Whole electric power consumption of a building Hvac system Heating Circulating pump Oter... systems and equipments Equipments on Socket Special function room Electrically driven heating equipment Chiller Fan of cooling tower Chilled pump cooling pump Air hand unit Fresh air hand unit Fan coil unit Air conditioner Heating water system drinking...

Yuan, W.

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Reducing auxiliary power consumption with F. D. fans  

SciTech Connect (OSTI)

On June 6, 1988, the Unit No. 1-A forced draft fan at Cayuga station failed in service. This failure and the subsequent replacement of the 1-A F.D. fan and 1.-B F.D. fan with a more energy efficient design, resulted in a reduction in auxiliary power consumption by 2,000 Kilo watts/hr. Annual savings are projected to be $129,000.00 for 1989. Cayuga station was designed and constructed with pressurized boilers. The forced draft fans supplied combustion air, and also were designed to force this air through the entire boiler. In 1975, induced draft (I.D.) fans were installed. This design change modified the boiler to a balanced draft system, which reduced the force or pressure of the air that the F.D. fans were required to supply. Operating as a balance draft unit, the station had considerably more F.D. fan capacity than was necessary. After the failure, a system and economic evaluation warranted a change in design specifications for the F.D. fans, with the quantity of air remaining unchanged, but supplied at a lower pressure. This paper deals with the cause of failure, economic details and justification of the new design fans, as well as the final testing of the fans after being placed in service.

Henson, G.E. (PSI Energy, Cayuga Generating Station, Cayuga, IN (US))

1990-01-01T23:59:59.000Z

82

Fan Energy Savings Decisions  

E-Print Network [OSTI]

Axial fans are used for thousands of industrial applications consuming millions of kilowatts daily. The decision that saves dollars is to either automatically change fan speed or change blade pitch to save up to 50 percent of consumed power over a...

Monroe, R. C.

83

Estimation of Energy Baseline by Simulation for On-going Commissioning and Energy Saving Retrofit  

E-Print Network [OSTI]

Hz AHU-2 11 kW 53 Hz AHU-3 11 kW 57 Hz AHU-4 3.7 kW 51 Hz AHU-5 2.2 kW 33 Hz Fan of AHU (Computer room) AHU-PC 3.0 kW - Lavatory ventilation fan FAN-TW 2.2 kW - P-L1 9.59 kW - P-L2 13.1 kW - Elevator - - - Fan coil units (33 units) - 10.22 k...

Miyata, M.; Yoshida, H.; Asada, M.; Iwata, T.; Tanabe, Y.; Yanagisawa, T.

2006-01-01T23:59:59.000Z

84

Record of Communication Concerning Ceiling Fan and Ceiling Fan...  

Broader source: Energy.gov (indexed) [DOE]

This memo provides an overview of communications made to DOE staff on the subject of possible changes to standards and test procedures for ceiling fans and ceiling fan light kits....

85

Submarine-fan sedimentation, Ouachita Mountains, Arkansas and Oklahoma  

SciTech Connect (OSTI)

More than 10,000 m (32,808 ft) of interbedded sandstones and shales comprise the Upper Mississippian and Lower Pennsylvanian flysch succession (Stanley, Jackfork, Johns Valley, Atoka) in the Ouachita Mountains of Arkansas and Oklahoma. Deposited primarily by turbidity current and hemipelagic processes in bathyal and abyssal water depths, these strata formed major submarine-fan complexes that prograded in a westward direction along the axis of an elongate remnant ocean basin that was associated with the collision and suturing of the North American and African-South American plates. A longitudinal fan system is visualized as the depositional framework for these strata, which were deposited in a setting analogous to the modern Bengal fan of the Indian Ocean. Facies analysis of the Jackfork formation indicates that inner fan deposits are present in the vicinity of Little Rock, Arkansas; middle fan channel and interchannel deposits occur at DeGray Dam and Friendship, Arkansas; and outer fan depositional-lobe deposits are present in southeastern Oklahoma. Boulder-bearing units (olistostromes), many with exotic clasts, were shed laterally into the Ouachita basin. They occur throughout the flysch succession and in all fan environments (i.e., inner, middle, and outer). This relationship may serve as a useful criterion for recognizing analogous longitudinal fan systems in the rock record.

Moiola, R.J.; Shanmugam, G.

1984-09-01T23:59:59.000Z

86

Comparison of modern Mississippi fan with selected ancient fans  

SciTech Connect (OSTI)

A comparison of the modern passive-margin Mississippi fan (DSDP Leg 96) with selected ancient active-margin fans reveals major differences in turbidite facies associations and seismic characteristics of the lower fan area. The lower Mississippi fan is composed of channel (facies B and F) and nonchannel sequences (facies C. and D), whereas lower fan areas of ancient active-margin fans are characterized by nonchannelized, thickening-upward depositional lobes (facies C and D) with sheetlike geometry. An absence of depositional lobes in the lower Mississippi fan is also suggested by a lack of mounded seismic reflections. Continuous and parallel seismic reflections of the lower Mississippi fan may represent sheet sands, but not those of true depositional lobes. In mature passive-margin fans, long, sinuous channels develop as a consequence of low gradients and the transport of sediment with a relatively low sand/mud ratio, and these channels develop lenticular sand bodies. In contrast, channels in active-margin fans are short and commonly braided as a result of high gradients and the transport of sediment with a relatively high sand/mud ratio. Braided channels characteristically develop sheetlike sand bodies.

Shanmugam, G.; Moiola, R.J.; McPherson, J.G.; O'Connell, S.

1988-09-01T23:59:59.000Z

87

E-Print Network 3.0 - air-conditioning units part Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

fans... : Use of mechanical equipment such as refrigeration, air conditioning, heating systems, ventilating fans... -handling units and mechanical, compressed air, and electric ......

88

Benefits of Prospective Commissioning for Condominiums in Chicago  

E-Print Network [OSTI]

by incremental electric heaters and a direct expansion fan-coil unit. The garage levels are ventilated with wall mounted exhaust fans and outside air intake louvers, and incorporate CO sensor override controls, while heat is provided by hot water unit heaters.... The mechanical room contains the main heating and cooling equipment, including water boilers, hot water pumps, chilled water pumps, make-up air unit, and domestic water heaters. The water boiler provides hot water for the heating loop, circulated by hot water...

Chimack, M.; Walker, C.

2004-01-01T23:59:59.000Z

89

Fan System Assessment- End User Training  

Office of Energy Efficiency and Renewable Energy (EERE)

Optimizing industrial fan systems can take on many forms, but any fan optimization project must meet the needs of the process. This self-paced workshop highlights the benefits of fan system...

90

Hunter Fan: Order (2014-CE-32008)  

Broader source: Energy.gov [DOE]

DOE ordered Hunter Fan Company to pay a $8,000 civil penalty after finding Hunter Fan had failed to certify that certain models of ceiling fans comply with the applicable energy conservation standards.

91

Save Energy with Axial Fans  

E-Print Network [OSTI]

= Trdh = CFM AAPP. A APPROACH V A~PROACH VAPP. < .5VFAN APPROACH VELOCITY FIG .? A 14 ft. fan, whose design flow as ,J,OOO CFr?1 in a ring 5 feet from grade would have an Area Approach of 220 ft 2 and a'V approach of 1137 FPM. The velocity... through the fan itself would be rOlfjhly: 250,000 or 1624 FPM .785 (14)2 As a rule of thumb, the approach velocity should not exceed 50% of the velocity through the fan. The high approach would cause additional velocity pres sure losses that were...

Monroe, R. C.

1981-01-01T23:59:59.000Z

92

air handling unit: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

case of fans, or indirectly, in the case of heat exchangers, which impose loads on the chiller and boiler plant. Air-handling units can comprise a myriad of subsystems (fans,...

93

air handling units: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

case of fans, or indirectly, in the case of heat exchangers, which impose loads on the chiller and boiler plant. Air-handling units can comprise a myriad of subsystems (fans,...

94

Matthews Fan: Proposed Penalty (2014-CE-32012)  

Broader source: Energy.gov [DOE]

DOE alleged in a Notice of Proposed Civil Penalty that Matthews-Gerbar, Ltd. d/b/a Matthews Fan Company failed to certify a variety of ceiling fans as compliant with the applicable energy conservation standards.

95

Experimental Evaluation of Installed Cooking Exhaust Fan Performance  

SciTech Connect (OSTI)

The installed performance of cooking exhaust fans was evaluated through residential field experiments conducted on a sample of 15 devices varying in design and other characteristics. The sample included two rear downdraft systems, two under-cabinet microwave over range (MOR) units, three different installations of an under-cabinet model with grease screens across the bottom and no capture hood, two devices with grease screens covering the bottom of a large capture hood (one under-cabinet, one wall-mount chimney), four under-cabinet open hoods, and two open hoods with chimney mounts over islands. Performance assessment included measurement of airflow and sound levels across fan settings and experiments to quantify the contemporaneous capture efficiency for the exhaust generated by natural gas cooking burners.Capture efficiency is defined as the fraction of generated pollutants that are removed through the exhaust and thus not available for inhalation of household occupants. Capture efficiency (CE) was assessed for various configurations of burner use (e.g., single front, single back, combination of one front and one back, oven) and fan speed setting. Measured airflow rates were substantially lower than the levels noted in product literature for many of the units. This shortfall was observed for several units costing in excess of $1000. Capture efficiency varied widely (from<5percent to roughly 100percent) across devices and across conditions for some devices. As expected, higher capture efficiencies were achieved with higher fan settings and the associated higher air flow rates. In most cases, capture efficiencies were substantially higher for rear burners than for front burners. The best and most consistent performance was observed for open hoods that covered all cooktop burners and operated at higher airflow rates. The lowest capture efficiencies were measured when a front burner was used with a rear backdraft system or with lowest fan setting for above the range systems that do not cover the front burners.

Singer, Brett C.; Delp, William W.; Apte, Michael G.

2010-11-01T23:59:59.000Z

96

Experimental Evaluation of Installed Cooking Exhaust Fan Performance  

E-Print Network [OSTI]

High High Fan (cfm) Burner Fire Btu/hr A- 50 Fan/Plume EffLow Fan (cfm) Burner Fire Btu/hr Fan/Plume Eff Figure  3.  Med Fan (cfm) Burner Fire Btu/hr Fan/Plume Eff Figure  7.  

Singer, Brett C.

2011-01-01T23:59:59.000Z

97

Xudong Fan Curriculum Vitae Curriculum Vitae  

E-Print Network [OSTI]

Xudong Fan Curriculum Vitae 1 Curriculum Vitae (Last updated: October 28, 2009) Xudong (Sherman Research Assistant and Teaching Assistant, #12;Xudong Fan Curriculum Vitae 2 Physics Department and Oregon in Opto-fluidic Ring Resonators for #12;Xudong Fan Curriculum Vitae 3 Ultrasensitive Biomolecule Detection

Fan, Xudong "Sherman"

98

DOE Zero Energy Ready Home Case Study: Amerisips Homes, Charleston...  

Energy Savers [EERE]

walls and 8.25-in. SIPs in the floor and roof. The HVAC system includes an air-to-water heat pump with fan coil that provides heat, ventilation, and hot water at 4.5 COP, plus a...

99

E-Print Network 3.0 - assembly diagram dwg Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

COLLECTOR DOMESTIC HEATINGCOOLINGPANELHOT WATER FAN COIL... SHOWN IN DASHED BOX ICE BIN Fig. 3.2. Space-heating schematic. 12;10 ORNL-DWG 78-9380R SOLAR COLLECTOR Source:...

100

Mechanical and Electrical Systems for the Tallest Building/Man-Made Structure in the World: A Burj Dubai Case Study  

E-Print Network [OSTI]

of the Persian Gulf. Its location coincides with the northern edge of the earth’s equatorial region, an area influenced by so-called trade wind patterns. The climate is classified as arid sub-tropical and is characterized by average diurnal temperature... for variable speed fan coil unit is included in the project. Chilled water pumps and air handling unit, where possible, are equipped with variable speed drives. Photovoltaic paneling was considered to be placed on the spire to provide electricity; however...

Frechette, R.; Leung, L.; Boyer, J.

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Fan deltas and braid deltas: conceptual problems  

SciTech Connect (OSTI)

The concept of fan deltas has been widely misinterpreted in the geologic literature. A true fan delta is defined as an alluvial fan deposited into a standing body of water. Such sequences are of limited areal extent and are, as expected, uncommon in the rock record. By contrast, braid deltas (herein defined), formed by progradation of a braided fluvial system into a standing body of water, are a common geomorphic feature in many modern settings, and their deposits are common in the geologic record. Braid-delta sequences are often identified as fan deltas, on the false premise that coarse-grained deposits in a deltaic setting are always part of an alluvial fan complex. The authors find that most published examples of so called fan deltas contain no direct evidence for the presence of an alluvial fan. Even in examples where an alluvial fan could be documented, the authors found that, in many cases, the alluvial fan complex was far removed from the shoreline, separated by an extensive braid plain. The authors suggest that such systems are better classified as braid deltas. They consider that it is essential to distinguish the environmental setting of true fan deltas from that of braid deltas. Misclassification will lead to incorrect interpretations of expected facies, sandstone geometry, reservoir quality, and tectonic settings. Criteria based on geometry, vertical and lateral lithofacies associations, and paleocurrent patterns should be used to correctly identify and distinguish these depositional systems.

McPherson, J.G.; Shanmugam, G.; Moiola, R.J.

1986-05-01T23:59:59.000Z

102

Building Pressure Control in VAV System with Relief Air Fan  

E-Print Network [OSTI]

, recently, Wang and Liu developed a motor power based fan airflow station., which determines the fan airflow using the measured fan motor power, the fan speed or control system command to VFD, and the in-situ fan motor power curve. Since the fan power... power can be obtained directly from VFD [5]. The motor power based fan airflow station method can be applied to the fan-tracking to perform a better building pressurization. The theory of the motor power based fan airflow station can be referred...

Pang, X.; Liu, M.; Zheng, B.

2005-01-01T23:59:59.000Z

103

Ceiling Fan | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin:Energy Information on PV EconomicsOregon: Energy ResourcesCeiling Fan Jump

104

Development of a High Efficiency Ceiling Fan  

E-Print Network [OSTI]

The potential of ceiling fans to improve comfort during the cooling season is well documented (Rohles et al.. 1983; Fairey et al.. 1986). There are at least two cases: In the first where air conditioning is unavailable, adding ceiling fans may...

Parker, D. S.; Callahan, M. P.; Sonne, J. K.; Su, G. H.; Hibbs, B. D.

2000-01-01T23:59:59.000Z

105

Matthews Fan: Order (2014-CE-32012)  

Broader source: Energy.gov [DOE]

DOE ordered Matthews-Gerbar, Ltd. d/b/a Matthews Fan Company to pay a $8,000 civil penalty after finding Matthews had failed to certify that certain models of ceiling fans comply with the applicable energy conservation standards.

106

Fan-fold shielded electrical leads  

DOE Patents [OSTI]

Disclosed are fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate. 3 figs.

Rohatgi, R.R.; Cowan, T.E.

1996-06-11T23:59:59.000Z

107

Fan-fold shielded electrical leads  

DOE Patents [OSTI]

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate.

Rohatgi, Rajeev R. (Mountain View, CA); Cowan, Thomas E. (Livermore, CA)

1996-01-01T23:59:59.000Z

108

An Analysis of a Turbo-Fan Used to Improve the Velocity Distribution in a Low Speed Wind-Tunnel  

E-Print Network [OSTI]

The Pressure Drop Across the Turbo-fan The blade element theory of rotors will be used to obtain 4 an expression for the pressure drop across the turbo-fan. A new frame of reference will be adopted. The turbo-fan is considered to be moving at the velocity... where c , the section lift coefficient and c , the section drag coefficient are inter- preted as vectors. In wing theory, including rotor theory, it is assumed that any blade section is subject to the same force per unit length as a two dimensional...

Wells, Otis Dean

1960-01-01T23:59:59.000Z

109

Morphology and seismic stratigraphy of the Toyama deep sea fan  

E-Print Network [OSTI]

are found in all fan regions, although facies F is more plentiful in slope regions. Since facies C, D, and G are found in both non-fan and lower fan turbi- dite sequences, fan deposits must be distinguished by their thickening and coarsening...

Shepherd, David Barton

1990-01-01T23:59:59.000Z

110

Performance Assessment of Photovoltaic Attic Ventilator Fans  

E-Print Network [OSTI]

has long been identified as a method to abate such heat gains. We present test results from using the photovoltaic (PV) attic ventilator fans in a test home to assess impact on attic and cooling energy performance....

Parker, D. S.; Sherwin, J. R.

2000-01-01T23:59:59.000Z

111

Synchronous and Cogged Fan Belt Performance Assessment  

SciTech Connect (OSTI)

The GSA Regional GPG Team commissioned the National Renewable Energy Laboratory (NREL) to perform monitoring of cogged V-belts and synchronous belts on both a constant volume and a variable air volume fan at the Byron G. Rodgers Federal Building and U.S. Courthouse in Denver, Colorado. These motor/fan combinations were tested with their original, standard V-belts (appropriately tensioned by an operation and maintenance professional) to obtain a baseline for standard operation. They were then switched to the cogged V-belts, and finally to synchronous belts. The power consumption by the motor was normalized for both fan speed and air density changes. This was necessary to ensure that the power readings were not influenced by a change in rotational fan speed or by the power required to push denser air. Finally, energy savings and operation and maintenance savings were compiled into an economic life-cycle cost analysis of the different belt options.

Cutler, D.; Dean, J.; Acosta, J.

2014-02-01T23:59:59.000Z

112

Best Practices for Energy Efficient Cleanrooms: Fan-Filter Tengfang Xu  

E-Print Network [OSTI]

LBNL-58639 Best Practices for Energy Efficient Cleanrooms: Fan-Filter Units Tengfang Xu June 15 by the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Building Technology, U.S. Department of Energy under Contract No. DE-AC02-05CH11231. #12;Best Practice for Energy Efficient Cleanrooms

113

Performance Assessment of Photovoltaic Attic Ventilator Fans  

Broader source: Energy.gov [DOE]

A case study of photovoltaic attic ventilator fans was conducted on an occupied single family home in Central Florida. Two fans were installed at mid-summer in an instrumented home where attic air temperature, meteorological conditions and space cooling electric power were measured. The home already had an attic radiant barrier, but still experienced attic air temperatures in excess of 130oF.

114

E-Print Network 3.0 - alluvial fan deposits Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

FANS: THE VENEZUELA DEBRIS FLOW AND FLASH FLOOD DISASTER Summary: and flood hazard sediment deposition in an alluvial fan on alluvial fans extremely dangerous. channel... ) in...

115

The effect of fan and heat sink design on heat removal from microprocessor chips  

E-Print Network [OSTI]

Air flow and heat removal characteristics for fan/heat sink designs used to cool Pentium class processors were analyzed. Five designs were tested for fan speed, differential and static nozzle pressure, static fan pressure, fan input current...

Baltrip, Kedra G

1997-01-01T23:59:59.000Z

116

Training: Fan Systems | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from theDepartment of EnergyThe Sun andDepartment ofFan Systems Training: Fan

117

DOE Publishes Final Rule for Residential Furnace Fan Test Procedure...  

Broader source: Energy.gov (indexed) [DOE]

Residential Furnace Fan Test Procedure DOE Publishes Final Rule for Residential Furnace Fan Test Procedure January 3, 2014 - 12:00am Addthis The Department of Energy (DOE) has...

118

Ultra-short nacelles for low fan pressure ratio propulsors  

E-Print Network [OSTI]

This thesis addresses the uncharted inlet and nacelle design space for low pressure ratio fans for advanced aeroengines. A key feature in low fan pressure ratio (FPR) propulsors with short inlets and nacelles is the increased ...

Peters, Andreas, Ph. D. Massachusetts Institute of Technology

2014-01-01T23:59:59.000Z

119

Cooling Tower Energy Conservation Through Hydraulic Fan Drives  

E-Print Network [OSTI]

Fan Drive Eliminates These Problems from the Drive Train. The electric motor is at ground level; close coupled to a hydraulic pump, filters and oil reservoir. Hydraulic lines bring oil flow to the lightweight hydraulic motor mounted at the fan... Tower Fan Drives Are Many: It removes the hazard of costly fan wrecks and shaft coupling breakage. It eliminates gearbox maintenance, breakdown or replacement. The electric motor is mounted with the reservoir and pump at ground level for ease...

Dickerson, J.

120

Knowing fans, knowing music : an exploration of fan interaction on Twitter  

E-Print Network [OSTI]

and the Origins of Music Fandom in Nineteenth-CenturyAmerica. ” In Fandom: Identities and Communities in aWhy Study Fans? ” In Fandom: Identities and Communities in a

McCollum, Nick

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Adjustable Speed- A Tool for Saving Energy Losses in Pumps, Fans, Fans, Blowers and Compressors  

E-Print Network [OSTI]

Petroleum and chemical plants of today are effectively cutting energy losses in their plants thermally, electrically, and mechanically in their process equipment. In rotating process equipment such as pumps, fans, compressors, and blowers, much...

Hickok, H. N.

122

An introduction to financial econometrics Jianqing Fan  

E-Print Network [OSTI]

An introduction to financial econometrics Jianqing Fan Department of Operation Research econometrics? This simple question does not have a simple answer. The boundary of such an interdisciplinary speaking, financial econometrics is to study quantitative problems arising from finance. It uses sta

Wang, Lily

123

Fan-beam intensity modulated proton therapy  

SciTech Connect (OSTI)

Purpose: This paper presents a concept for a proton therapy system capable of delivering intensity modulated proton therapy using a fan beam of protons. This system would allow present and future gantry-based facilities to deliver state-of-the-art proton therapy with the greater normal tissue sparing made possible by intensity modulation techniques.Methods: A method for producing a divergent fan beam of protons using a pair of electromagnetic quadrupoles is described and particle transport through the quadrupole doublet is simulated using a commercially available software package. To manipulate the fan beam of protons, a modulation device is developed. This modulator inserts or retracts acrylic leaves of varying thickness from subsections of the fan beam. Each subsection, or beam channel, creates what effectively becomes a beam spot within the fan area. Each channel is able to provide 0–255 mm of range shift for its associated beam spot, or stop the beam and act as an intensity modulator. Results of particle transport simulations through the quadrupole system are incorporated into the MCNPX Monte Carlo transport code along with a model of the range and intensity modulation device. Several design parameters were investigated and optimized, culminating in the ability to create topotherapy treatment plans using distal-edge tracking on both phantom and patient datasets.Results: Beam transport calculations show that a pair of electromagnetic quadrupoles can be used to create a divergent fan beam of 200 MeV protons over a distance of 2.1 m. The quadrupole lengths were 30 and 48 cm, respectively, with transverse field gradients less than 20 T/m, which is within the range of water-cooled magnets for the quadrupole radii used. MCNPX simulations of topotherapy treatment plans suggest that, when using the distal edge tracking delivery method, many delivery angles are more important than insisting on narrow beam channel widths in order to obtain conformal target coverage. Overall, the sharp distal falloff of a proton depth-dose distribution was found to provide sufficient control over the dose distribution to meet objectives, even with coarse lateral resolution and channel widths as large as 2 cm. Treatment plans on both phantom and patient data show that dose conformity suffers when treatments are delivered from less than approximately ten angles. Treatment time for a sample prostate delivery is estimated to be on the order of 10 min, and neutron production is estimated to be comparable to that found for existing collimated systems.Conclusions: Fan beam proton therapy is a method of delivering intensity modulated proton therapy which may be employed as an alternative to magnetic scanning systems. A fan beam of protons can be created by a set of quadrupole magnets and modified by a dual-purpose range and intensity modulator. This can be used to deliver inversely planned treatments, with spot intensities optimized to meet user defined dose objectives. Additionally, the ability of a fan beam delivery system to effectively treat multiple beam spots simultaneously may provide advantages as compared to spot scanning deliveries.

Hill, Patrick [Department of Radiation Oncology, University of Iowa Hospitals and Clinics, Iowa City, Iowa 52242 (United States)] [Department of Radiation Oncology, University of Iowa Hospitals and Clinics, Iowa City, Iowa 52242 (United States); Westerly, David [Department of Radiation Oncology, University of Colorado School of Medicine, Aurora, Colorado 80045 (United States)] [Department of Radiation Oncology, University of Colorado School of Medicine, Aurora, Colorado 80045 (United States); Mackie, Thomas [Medical Devices, Morgridge Institute for Research, University of Wisconsin, Madison, Wisconsin 53715 (United States)] [Medical Devices, Morgridge Institute for Research, University of Wisconsin, Madison, Wisconsin 53715 (United States)

2013-11-15T23:59:59.000Z

124

Williston Lodgepole play fans out  

SciTech Connect (OSTI)

The Williston basin Mississippian Lodgepole oil play is swelling the rig count and oil production in North Dakota. As much as 200 sq miles of 3D seismic surveys have been acquired in southwestern North Dakota, and at least as much more is expected to be gathered through next year. Exploratory drilling so far has moved south and east for Conoco Inc.`s 1993 Lodgepole discovery in Dickinson oil field. The play also seems destined to become active in Montana. OGJ estimates North Dakota`s oil production at about 84,000 b/d, up from 75,000 b/d at the same time a year ago. State restrictions pending field unitization have reined production. The paper briefly describes the boundary of the basin and give a summary of the field.

Petzet, G.A.

1995-10-02T23:59:59.000Z

125

Final Report Independent Verification Survey of the High Flux Beam Reactor, Building 802 Fan House Brookhaven National Laboratory Upton, New York  

SciTech Connect (OSTI)

On May 9, 2011, ORISE conducted verification survey activities including scans, sampling, and the collection of smears of the remaining soils and off-gas pipe associated with the 802 Fan House within the HFBR (High Flux Beam Reactor) Complex at BNL. ORISE is of the opinion, based on independent scan and sample results obtained during verification activities at the HFBR 802 Fan House, that the FSS (final status survey) unit meets the applicable site cleanup objectives established for as left radiological conditions.

Harpeneau, Evan M. [Oak Ridge Institute for Science and Education, Oak Ridge, TN (United States). Independent Environmental Assessment and Verification Program

2011-06-24T23:59:59.000Z

126

eUnitedStates,China,andGlobalGovernance: A New Agenda for a New Era  

E-Print Network [OSTI]

eUnitedStates,China,andGlobalGovernance: A New Agenda for a New Era e Research Center for Chinese of Social Sciences April 2013 2013 4 Scott Kennedy He Fan #12;The United States, China, and Global, Beijing, China Authors: Scott Kennedy and He Fan Production Editor: Andrea Wald Printer: Rongda Quick

Indiana University

127

Development of Power-head based Fan Airflow Station  

E-Print Network [OSTI]

related to the measured fan speed. Actually the measured fan speed is assumed to equal the motor synchronous speed, which is proportional to the VFD frequency. Theoretically it is not true. The difference between the synchronous speed and motor speed... the basic theory, experiment and results of the power-head based airflow station. Theory Figure 1 shows variable speed fan connection schematic. VFD is normally installed on the motor to adjust the motor speed by modulating frequency. Typically...

Wang, G.; Liu, M.

2005-01-01T23:59:59.000Z

128

Appearance Learning by Adaptive Kalman Filters for FLIR Tracking Vijay Venkataraman, Guoliang Fan, Xin Fan  

E-Print Network [OSTI]

Appearance Learning by Adaptive Kalman Filters for FLIR Tracking Vijay Venkataraman, Guoliang Fan the challenging issue of target tracking and appearance learning in Forward Looking In- frared (FLIR) sequences existing methods and experiments on the AMCOM FLIR dataset validate its effectiveness. 1. Introduction

Fan, Guoliang

129

Target Tracking with Online Feature Selection in FLIR Imagery Vijay Venkataraman, Guoliang Fan and Xin Fan  

E-Print Network [OSTI]

Target Tracking with Online Feature Selection in FLIR Imagery Vijay Venkataraman, Guoliang Fan tracking algo- rithm for FLIR imagery. A dual foreground and background model is proposed for target that the proposed algorithm can accurately track poorly-visible targets in FLIR imagery even with strong ego

Fan, Guoliang

130

GEA Heat Exchangers GEA Searle Cooler and Condensing Unit Ranges  

E-Print Network [OSTI]

have high efficiency EC fans as standard across the range. All our commercial unit coolers have whiteUnits GEA Searle Condensing Units are supplied as standard to a high specification with a complete controlGEA Heat Exchangers GEA Searle Cooler and Condensing Unit Ranges Top-level engineering solutions

Frandsen, Søren

131

Cooling Effects of Fans | GE Global Research  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-Series to User GroupInformationE-Gov ContactsContractOfficeCoolWhy Do Fans Make

132

Fans for Cooling | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelinesProvedDecember 2005DepartmentDecember U.S. Department-5 METRICNatural GasFactFans for

133

Use of VFDs on Asphalt Plant Induced Draft Fans  

E-Print Network [OSTI]

paybacks were 3-5 years before utility incentives. In the 10 plants evaluated, the ID fans accounted for as much as 30% of the total plant electrical consumption. In the majority of these plants the outlet dampers were typically 50%-60% closed. Fan motors...

Anderson, G. R.; Case, P. L.; Lowery, J.

2005-01-01T23:59:59.000Z

134

Choosing the right boiler air fans at Weston 4  

SciTech Connect (OSTI)

When it came to choosing the three 'big' boiler air fans - forced draft, induced draft and primary air, the decision revolved around efficiency. The decision making process for fan selection for the Western 4 supercritical coal-fired plant is described in this article. 3 photos.

Spring, N.

2009-04-15T23:59:59.000Z

135

Heuristics for Balancing Turbine Fans Samir V. Amiouny  

E-Print Network [OSTI]

Reiger, 1986. In some cases, such as in the constructionof hydraulic, steam or gas turbines, fan bladesHeuristics for Balancing Turbine Fans Samir V. Amiouny John J. Bartholdi, III John H. Vande Vate April 20, 1997 Abstract We develop heuristics for a problem that models the static balancing of turbine

Bartholdi III, John J.

136

E-Print Network 3.0 - alluvial fan nye Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Abstract. Alluvial fans of alpine torrents are both natural deposition areas for sediment discharged... on alluvial fans depends on proper iden- tification of ... Source:...

137

Costs and benefits of energy efficiency improvements in ceiling fans  

SciTech Connect (OSTI)

Ceiling fans contribute significantly to residential electricity consumption, especially in developing countries with warm climates. The paper provides analysis of costs and benefits of several options to improve the efficiency of ceiling fans to assess the global potential for electricity savings and green house gas (GHG) emission reductions. Ceiling fan efficiency can be cost-effectively improved by at least 50% using commercially available technology. If these efficiency improvements are implemented in all ceiling fans sold by 2020, 70 terawatt hours per year could be saved and 25 million metric tons of carbon dioxide equivalent (CO2-e) emissions per year could be avoided, globally. We assess how policies and programs such as standards, labels, and financial incentives can be used to accelerate the adoption of efficient ceiling fans in order to realize potential savings.

Shah, Nihar; Sathaye, Nakul; Phadke, Amol; Letschert, Virginie [Lawrence Berkeley National Lab., CA (United States). Environmental Energy Technology Division] [Lawrence Berkeley National Lab., CA (United States). Environmental Energy Technology Division

2013-10-15T23:59:59.000Z

138

Method for fabricating fan-fold shielded electrical leads  

DOE Patents [OSTI]

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate. 3 figures.

Rohatgi, R.R.; Cowan, T.E.

1994-12-27T23:59:59.000Z

139

Method for fabricating fan-fold shielded electrical leads  

DOE Patents [OSTI]

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate.

Rohatgi, Rajeev R. (Mountain View, CA); Cowan, Thomas E. (Livermore, CA)

1994-01-01T23:59:59.000Z

140

Laurentian fan: morphology, sediments, processes, and growth pattern  

SciTech Connect (OSTI)

Thick sediment accumulations in deep water provide a new target in the search for oil, and require an innovative approach to hydrocarbon exploration. The Laurentian fan is a large, deep-sea (2000 to 5000 m) fan in the western North Atlantic, and has been the major depocenter off Nova Scotia since at least the early Tertiary. The main development of the present depositional and erosional fan morphology in the past 2 to 3 m.y. was closely related to onshore glacial history. The slope above the fan has been the site of rapid sedimentation and consequent slumping. A network of tributaries on the upper fan appears to feed three main channel systens incised up to 800 m between broad asymmetric levees. These channels meander widely across the lower fan, then die out abruptly and pass into a lobate suprafan. Differences between the Laurentian fan and typical fan models result, in part, from the muddy nature of the sediment and the supply system. The channels contain thick, coarse gravels which probably grade distally into sandy lobes. Both should produce good reservoir bodies with suitable source and trapping mechanisms. Fine-grained sediments were more important in fan construction. Interbedded turbidites, contourites, and hemipelagites are present in the late Quaternary-Holocene sequence. The distribution of these sediments and, in particular, the recognition of structural sequences, textural trends, and fabric types in the fine-grained turbidites can be used to characterize particular parts of the fan environment. The development of this approach should prove useful in future hydrocarbon exploration.

Stow, D.A.V.

1981-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Improvement of efficiency in a low volume fan  

E-Print Network [OSTI]

Admission 37 4. 5 Inlet Stator Vanes 4. 6 Blade Height Modification 4. 7 Final Modification 38 44 CHAPTER V CONCLUSION AND RECOMMENDATIONS 51 Vi REFERENCES APPENDIX A Page 53 PROGRAM TO COMPUTE FAN CHARACTERISTICS 54 APPENDIX B AIR MOVING... AND CONDITIONING ASSOCIATION TEST CODE 59 VITA 76 Figure 1. 1 1. 2 2. 1 LIST OF FIGURES Title Blade Velocity Diagrams Typical Centrifugal Fan Original Fan Rig Page 10 2. 2 2. 3 Pitot Traverse In Outlet Duct 12 Electric Motor Calibration Curve 14 2...

Lipscomb, Jeffrey William

1974-01-01T23:59:59.000Z

142

Duplex-like structures in submarine fan channels, Ouachita Mountains, Arkansas  

SciTech Connect (OSTI)

Submarine fan channel sequences of the Jackfork Formation (Lower Pennsylvanian) at DeGray Dam section in the Ouachita Mountains, Arkansas, contain discrete units (10-75 cm thick) with moderately dipping (25/sup 0/-40/sup 0/), sigmoidal imbricate slices. Adjacent units with opposing imbricate slices are common. The sigmoidal structures are similar in geometry to a tectonic feature known as a duplex. A tectonic origin of sigmoidal structures, however, seems unlikely because opposing directions of imbrication in adjacent units would require an unrealistic tectonic movement history for the area. The authors propose that the Jackfork sigmoidal structures were formed by a process kinematically similar to that responsible for generating duplex structures. Unlike tectonic duplexes, however, the sigmoidal structures were formed by soft-sediment deformation of sand and mud layers as high-energy sediment gravity flows glided over these layers. Sediment gravity flows, responsible for forming the sigmoidal deformation, were probably generated by slumping of adjacent channel walls. Dip direction of sigmoidal slices is perpendicular to channel axes. Thus, recognition of sigmoidal deformation structures may be useful in inferring the trend of channels in ancient submarine fan complexes.

Shanmugam, G.; Moiola, R.J.; Sales, J.K.

1988-03-01T23:59:59.000Z

143

Fallout fans: Negotiations over text integrity in the age of the active audience  

E-Print Network [OSTI]

of these commentaries on the new economy are using the terms, ?fan,? ?fandom,? or ?fan culture,? yet their models rest on the same social behaviors and emotional commitments that fan scholars have been researching over the past several decades? (Jenkins, 2007, p. 359...), three preeminent fan scholars, declared that we have reached the ?fandom is beautiful? phase of fan studies (p. 3). Such claims about fan influence have also been made by influential fan scholar Henry Jenkins (2006a, 2006b, 2007), indicating a shift...

Milner, Ryan M.

2008-07-31T23:59:59.000Z

144

High Efficiency Fans and High Efficiency Electrical Motors  

E-Print Network [OSTI]

Replacing nominal efficient electrical motors with premium efficiency can save on electrical power costs in cotton gins. Connected horsepower load on industrial air fans is approximately 60% of the total horsepower in a typical cotton gin...

Breedlove, C. W.

145

New Energy Efficiency Standards for Furnace Fans to Reduce Carbon...  

Office of Environmental Management (EM)

by at least 3 billion metric tons in total by 2030, equal to more than a year's carbon pollution from the entire U.S. electricity system. Furnace fans are used to circulate air...

146

Modeling and ecodesigning crossflow ventilation fans with Mathematica  

E-Print Network [OSTI]

The efficiency of a simple model of crossflow fan is maximized when the geometry depends on a design parameter. The flow field is numerically computed using a Galerkin method for solving a Poisson partial differential equation.

Argentini, Gianluca

2010-01-01T23:59:59.000Z

147

Polycyclic aromatic hydrocarbon distributions in Mississippi Fan sediments  

E-Print Network [OSTI]

/ / / / / / glg. 4. Diag~am showing the morphology and lithologic bed associations of a submarine fan (adapted from IIANER, 1971). 16 indicative of land-sourced organic matter even in the intraslope basins. Furthermore, KENNICUTT et ai, (1986a) concluded.... Sandberg, B. A. , University of Colorado Chairman of Advisory Committee: Dr. James M. Brooks Polycyclic aromatic hydrocarbon (PAH) distributions in Upper Pleistocene sediments of the Mississippi Fan and two intraslope basins in the Gulf of Mexico...

Sandberg, William Allan

1986-01-01T23:59:59.000Z

148

COOLING FAN AND SYSTEM PERFORMANCE AND EFFICIENCY IMPROVEMENTS  

SciTech Connect (OSTI)

Upcoming emissions regulations (Tiers 3, 4a and 4b) are imposing significantly higher heat loads on the cooling system than lesser regulated machines. This work was a suite of tasks aimed at reducing the parasitic losses of the cooling system, or improving the design process through six distinct tasks: 1. Develop an axial fan that will provide more airflow, with less input power and less noise. The initial plan was to use Genetic Algorithms to do an automated fan design, incorporating forward sweep for low noise. First and second generation concepts could not meet either performance or sound goals. An experienced turbomachinery designer, using a specialized CFD analysis program has taken over the design and has been able to demonstrate a 5% flow improvement (vs 10% goal) and 10% efficiency improvement (vs 10% goal) using blade twist only. 2. Fan shroud developments, using an 'aeroshroud' concept developed at Michigan State University. Performance testing at Michigan State University showed the design is capable of meeting the goal of a 10% increase in flow, but over a very narrow operating range of fan performance. The goal of 10% increase in fan efficiency was not met. Fan noise was reduced from 0 to 2dB, vs. a goal of 5dB at constant airflow. The narrow range of fan operating conditions affected by the aeroshroud makes this concept unattractive for further development at this time 3. Improved axial fan system modeling is needed to accommodate the numbers of cooling systems to be redesigned to meet lower emissions requirements. A CFD fan system modeling guide has been completed and transferred to design engineers. Current, uncontrolled modeling practices produce flow estimates in some cases within 5% of measured values, and in some cases within 25% of measured values. The techniques in the modeling guide reduced variability to the goal of + 5% for the case under study. 4. Demonstrate the performance and design versatility of a high performance fan. A 'swept blade mixed flow' fan was rapid prototyped from cast aluminum for a performance demonstration on a small construction machine. The fan was mounted directly in place of the conventional fan (relatively close to the engine). The goal was to provide equal airflow at constant fan speed, with 75% of the input power and 5 dB quieter than the conventional fan. The result was a significant loss in flow with the prototype due to its sensitivity to downstream blockage. This sensitivity to downstream blockage affects flow, efficiency, and noise all negatively, and further development was terminated. 5. Develop a high efficiency variable speed fan drive to replace existing slipping clutch style fan drives. The goal for this task was to provide a continuously variable speed fan drive with an efficiency of 95%+ at max speed, and losses no greater than at max speed as the fan speed would vary throughout its entire speed range. The process developed to quantify the fuel savings potential of a variable speed fan drive has produced a simple tool to predict the fuel savings of a variable speed drive, and has sparked significant interest in the use of variable speed fan drive for Tier 3 emissions compliant machines. The proposed dual ratio slipping clutch variable speed fan drive can provide a more efficient system than a conventional single ratio slipping clutch fan drive, but could not meet the established performance goals of this task, so this task was halted in a gate review prior to the start of detailed design. 6. Develop a cooling system air filtration device to allow the use of automotive style high performance heat exchangers currently in off road machines. The goal of this task was to provide a radiator air filtration system that could allow high fin density, louvered radiators to operate in a find dust application with the same resistance to fouling as a current production off-road radiator design. Initial sensitivity testing demonstrated that fan speed has a significant impact on the fouling of radiator cores due to fine dusts, so machines equipped with continuously variabl

Ronald Dupree

2005-07-31T23:59:59.000Z

149

Annual Energy Consumption Analysis Report for Richland Middle School  

SciTech Connect (OSTI)

Richland Middle School is a single story, 90,000 square feet new school located in Richland, WA. The design team proposed four HVAC system options to serve the building. The proposed HVAC systems are listed as following: (1) 4-pipe fan coil units served by electrical chiller and gas-fired boilers, (2) Ground-source closed water loop heat pumps with water loop heat pumps with boiler and cooling tower, and (3) VAV system served by electrical chiller and gas-fired boiler. This analysis estimates the annual energy consumptions and costs of each system option, in order to provide the design team with a reasonable basis for determining which system is most life-cycle cost effective. eQuest (version 3.37), a computer-based energy simulation program that uses the DOE-2 simulation engine, was used to estimate the annual energy costs.

Liu, Bing

2003-12-18T23:59:59.000Z

150

Printed in the United States of America. Available from National Technical Information Service  

E-Print Network [OSTI]

of Refrigerant Charge .............. 7 3. DESCRIPTION OF TEST UNIT ................... 11 4. DESCRIPTION OF TEST.3 Fan Tests . . . . . . . . . . . . . . . . . . . . . . . . 22 5.4 Refrigerant Charge Tests .... . . .... 3 2.3 Heat Exchanger and Orifice-Type Refrigerant Metering Device Performance ............... 4 2

Oak Ridge National Laboratory

151

Blue fan palm distribution and seed removal patterns in three desert oases of northern Baja California, Mexico  

E-Print Network [OSTI]

DOI 10.1007/s11258-009-9682-4 Blue fan palm distribution anddistribution patterns of the blue fan palm, Brahea armata,evaluating (i) the levels of blue fan palm seed removal by

Wehncke, Elisabet V.; López-Medellín, Xavier; Ezcurra, Exequiel

2010-01-01T23:59:59.000Z

152

Performance and Stability Analysis of a Shrouded-Fan UAV  

E-Print Network [OSTI]

This paper deals with the estimation of the performance and stability for a shrouded-fan unmanned rotorcraft whose mission profile also prescribes the flight in ground effect. The not so simple estimation of the aerodynamic coefficients and of the thrust in the various situations makes the performance calculation and the stability analysis difficult tasks. This is due to the strong interaction between the fan flow and shroud that causes quite different flow structures about the airframe depending on flight conditions. A further difficulty is related to the ground effect which produces substantial modifications in the rotor thrust and aerodynamic coefficients. To evaluate performance and stability, two models have been developed. One determines the aerodynamic coefficients of the shroud, whereas the other one calculates thrust and moment of the rotors system. Both models take into account the mutual interference between fan flow and fuselage and ground effect. Performance and stability are then discussed with ...

de Divitiis, Nicola

2009-01-01T23:59:59.000Z

153

Geomorphology and morphometric characteristics of alluvial fans, Guadalupe Mountains National Park and adjacent areas, west Texas and New Mexico  

E-Print Network [OSTI]

............................................................ 29 14 Alluvial fans along the Guadalupe Mountains in Big Dog Canyon........ 31 15 Alluvial fans along the Brokeoff Mountains in Big Dog Canyon........... 35 16 View of alluvial fans from their drainage basins.................................. 75 27 Salt Basin-Brokeoff Mountains alluvial fan group ................................. 76 28 Big Dog Canyon-Brokeoff Mountains alluvial fan group....................... 77 29 Big Dog Canyon-Guadalupe Mountains alluvial fan group...

Given, Jeffrey Lyle

2004-09-30T23:59:59.000Z

154

Power Aware Page Allocation Alvin R. Lebeck Xiaobo Fan Heng Zeng  

E-Print Network [OSTI]

CS 2000 08 Power Aware Page Allocation Alvin R. Lebeck Xiaobo Fan Heng Zeng Carla Ellis Department@cs.duke.edu Xiaobo Fan Dept. of Computer Science Duke University Durham, NC 27708 USA xiaobo@cs.duke.edu Heng Zeng

Ellis, Carla

155

2014-10-27 Issuance: Test Procedure for Ceiling Fan Light Kits...  

Office of Environmental Management (EM)

27 Issuance: Test Procedure for Ceiling Fan Light Kits; Notice of Proposed Rulemaking 2014-10-27 Issuance: Test Procedure for Ceiling Fan Light Kits; Notice of Proposed Rulemaking...

156

Income Tax Deduction for Solar-Powered Roof Vents or Fans  

Broader source: Energy.gov [DOE]

Indiana allows taxpayers to take a deduction on solar-powered roof fans (or vent, also sometimes called an attic fan) installed in a home that the taxpayer owns or leases. The deduction is for 50%...

157

Laugh out loud in real life : women's humor and fan identity  

E-Print Network [OSTI]

The emerging field of fan studies has, until recently, been defined only by the research that has taken place within it. Almost universally, this research focuses on self-identified fans. However, scholars are beginning ...

Klink, Madeline LeNore

2010-01-01T23:59:59.000Z

158

Flexibility of Commercial Building HVAC Fan as Ancillary Service for Smart Grid  

E-Print Network [OSTI]

Efficient Building Control Systems, Smart Grid and AircraftCommercial Building HVAC Fan as Ancillary Service for Smart

Maasoumy, Mehdi

2013-01-01T23:59:59.000Z

159

Fan Aerodynamic Performance Guarantees: Do Your Policies, Procedures and Penalties Provide Adequate Certainty?  

E-Print Network [OSTI]

With few exceptions, fan vendors do not provide a written guarantee regarding aerodynamic performance. Some fan vendors even go so far as to state in their terms and conditions of sale that fan performance is not guaranteed unless it is specifically...

Kaufman, S. G.; Martin, V.; Falk, M. A.

2004-01-01T23:59:59.000Z

160

Boost Converter Provides Temperature-Controlled Operation of 12V Fan from +5V Supply  

E-Print Network [OSTI]

enclosure, and reducing the fan supply voltage when maximum cooling is not necessary. Reducing the operatingBoost Converter Provides Temperature-Controlled Operation of 12V Fan from +5V Supply John Mc converter shown in Fig. 1 allows operation of a 12V brushless DC fan from a +5V supply. The circuit is based

McNeill, John A.

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

The Forming of AISI 409 sheets for fan blade manufacturing  

SciTech Connect (OSTI)

The necessity of adapting the standardized fan models to conditions of higher temperature has emerged due to the growth of concern referring to the consequences of the gas expelling after the Mont Blanc tunnel accident in Italy and France, where even though, with 100 fans in operation, 41 people died. The objective of this work is to present an alternative to the market standard fans considering a new technology in constructing blades. This new technology introduces the use of the stainless steel AISI 409 due to its good to temperatures of gas exhaust from tunnels in fire situation. The innovation is centered in the process of a deep drawing of metallic sheets in order to keep the ideal aerodynamic superficies for the fan ideal performance. Through the impression of circles on the sheet plane it is shown, experimentally, that, during the pressing process, the more deformed regions on the sheet plane of the blade can not reach the deformation limits of the utilized sheet material.

Foroni, F. D.; Menezes, M. A.; Moreira Filho, L. A. [ITA - Aeronautic Technological Institute, IEM, Praca Mal. Eduardo Gomes, 50 - Vila das Acacias - S. J. Campos, Brasil - CEP 1228-900 (Brazil)

2007-04-07T23:59:59.000Z

162

Submarine fan lobe models: Implications for reservoir properties  

SciTech Connect (OSTI)

A multitude of submarine fan lobe models, advocating widely different reservoir properties, has been introduced into the sedimentologic literature. Four of these models are compared to show their differences in reservoir properties. Braided suprafan lobes are characterized by stacked sand bodies with good lateral and vertical communication, and they constitute excellent reservoir facies. The unchanneled depositional lobes, composed of sheetlike sand bodies with good lateral and moderate vertical communication, exhibit properties of good reservoir facies. Fanlobes, which refer to meandering channels and associated levee facies of large mud-rich submarine fans such as the Mississippi Fan in the Gulf of Mexico, are characterized by offset stacked sand bodies with poor lateral and vertical communication. These lenticular sands have the potential to be moderately good reservoir facies. Ponded lobes, which represent mud-rich slump facies of slope environments, comprise poor reservoir facies because of poor sand content and poor sand-body connectivity caused by chaotic bedding. Furthermore, the presence of slumped mud layers in ponded lobes is expected to hinder fluid flow. Because different lobe models vary significantly from one another in terms of reservoir properties, caution must be exercised to apply the proper lobe model to ancient fan sequences in hydrocarbon exploration and production.

Shanmugam, G.; Moiola, R.J. (Mobil Research and Development Corp., Dallas, TX (USA))

1990-09-01T23:59:59.000Z

163

LAB 3 Cleanroom Fan and Filters Analysis for the Supports  

SciTech Connect (OSTI)

A 1400 lb blower fan and a 2700 lb filter box are to be supported at Lab 3. The support structure is a framework that suspends from the building wall to the cleanroom and to a washroom. The framework is made of welded 4-inch x 8-inch x 1/4-inch rectangular A36 steel tube. Welds are to be standard prequalified welds as by AISC. The main support frame is approximately 7-feet off the floor and welded onto the top of 10 columns. A deflection and stress study was performed on the planned structure. A scaled plan view is given in drawing 3823.113-MD-358764. The heaviest loaded beams were labeled with a letter designation and were studied for beam deflections and stresses. The 4-inch x 8-inch rectangular tube was also used for the substructure for the fan and filter mounts and to support a temporary floor grating during maintenance.

Cease, H.; /Fermilab

1998-05-08T23:59:59.000Z

164

Evaluation of Retrofit Variable-Speed Furnace Fan Motors  

SciTech Connect (OSTI)

In conjunction with the New York State Energy Research and Development Authority (NYSERDA) and Proctor Engineering Group, Ltd. (PEG), the Consortium for Advanced Residential Buildings (CARB) has evaluated the Concept 3 (tm) replacement motors for residential furnaces. These brushless, permanent magnet (BPM) motors can use much less electricity than their PSC (permanent split capacitor) predecessors. This evaluation focuses on existing homes in the heating-dominated climate of upstate New York with the goals of characterizing field performance and cost-effectiveness. The results of this study are intended to be useful to home performance contractors, HVAC contractors, and home efficiency program stakeholders. The project includes eight homes in and near Syracuse, NY. Tests and monitoring was performed both before and after fan motors were replaced. Average fan power reductions were approximately 126 Watts during heating and 220 Watts during cooling operation. Over the course of entire heating and cooling seasons, these translated into average electric energy savings of 163 kWh. Average cost savings were $20 per year. Homes where the fan was used outside of heating and cooling mode saved an additional $42 per year on average. Results indicate that BPM replacement motors will be most cost-effective in HVAC systems with longer run times and relatively low duct static pressures. More dramatic savings are possible if occupants use the fan-only setting when there is no thermal load. There are millions of cold-climate, U.S. homes that meet these criteria, but the savings in most homes tested in this study were modest.

Aldrich, R.; Williamson, J.

2014-01-01T23:59:59.000Z

165

Improving Fan System Performance - A Sourcebook for Industry  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensionalthe U.S. Improving Fan System Performance a sourcebook for

166

Types of submarine fan lobes: Models and implications  

SciTech Connect (OSTI)

Different lobe models imply significantly different reservoir geometries; thus, one must apply the proper lobe model to ancient fan sequences. Braided suprafan lobes are characterized by stacked channel sand bodies with good lateral and vertical communication, and they constitute excellent reservoir facies. Depositional lobes, composed of sheet-like sand bodies with good lateral and moderate vertical communication, exhibit properties of good reservoir facies. Fanlobes, which refer to meandering channels and associated levee facies of large mud-rich submarine fans such as the Mississippi fan, are characterized by offset stacked sand bodies with poor lateral and vertical communication .These lenticular sands have the potential to be moderately good reservoir facies. Ponded lobes, which represent mud-rich slump facies of slope environments, comprise poor reservoir facies because of low sand content and poor sand-body connectivity. Furthermore, the presence of contorted mud layers in ponded lobes is expected to hinder fluid flow. External mounded reflections in seismic profiles often are interpreted as lobes; however, there are no definite seismic criteria to delineate mud-rich lobes from sand-rich lobes.

Shanmugam, G.; Moiola, R.J. (Mobil Research and Development Corp., Dallas, TX (United States))

1991-01-01T23:59:59.000Z

167

Basin-floor fans in the North Sea: Sequence stratigraphic models vs. sedimentary facies  

SciTech Connect (OSTI)

Examination of nearly 12,000 feet (3658m) of conventional core from Paleogene and Cretaceous deep-water sandstone reservoirs cored in 50 wells in 10 different areas or fields in the North Sea and adjacent regions reveals that these reservoirs are predominantly composed of mass-transport deposits, mainly sandy slumps and sandy debris flows. Sedimentary features indicating slump and debris-flow origin include sand units with sharp upper contacts; slump folds; discordant, steeply dipping layers (up to 60{degrees}); glide planes; shear zones; brecciated clasts; clastic injections; floating mudstone clasts; planar clast fabric; inverse grading of clasts; and moderate-to-high matrix content (5-30%). This model predicts that basin-floor fans are predominantly composed of sand-rich turbidites with laterally extensive, sheetlike geometries. However, calibration of sedimentary facies in our long (400-700 feet) cores with seismic and wire-line-log signatures through several of these basin-floor fans (including the Gryphon-Forth, Frigg, and Faeroe areas) shows that these features are actually composed almost exclusively of mass-transport deposits consisting mainly of slumps and debris flows. Distinguishing deposits of mass-transport processes, such as debris flows, from those of turbidity currents has important implications for predicting reservoir geometry. Debris flows, which have plastic flow rheology, can form discontinuous, disconnected sand bodies that are harder to delineate and less economical to develop than deposits of fluidal turbidity currents, which potentially produce more laterally continuous, interconnected sand bodies. Process sedimentological interpretation of conventional core is commonly critical for determining the true origin and distribution of reservoir sands.

Shanmugam, G.; Bloch, R.B. [Mobil Research and Development Corp., Dallas, TX (United States); Mitchell, S.M. [Mobil Exploration and Producing US, Inc., Dallas, TX (United States); Beamish, G.W.J.; Shields, K.E. [Mobil North Sea Ltd., London (United Kingdom); Hodgkinson, R.J.; Straume, T.; Syvertsen, S.E. [Mobil Exploration Norway, Inc., Stavanger (Norway); Damuth, J.E. [Univ. of Texas, Arlington, TX (United States)

1995-04-01T23:59:59.000Z

168

Development of In-Situ Fan Curve Measurement with One Airflow Measurement  

E-Print Network [OSTI]

Development of In-situ Fan Curve Measurement with One Airflow Measurement Guopeng Liu, Ik-Seong Joo, Li Song, Mingsheng Liu, Ph.D., P.E. Energy Systems Laboratory University of Nebraska ABSTRACT Fan airflow is the key parameter for air... is another issue for this method. Therefore, it is very important to find an effective way to measure the airflow accurately. An airflow control named VSD volumetric tracking (VSDVT) has been developed by Liu [13] recently. This method uses fan...

Liu, G.; Joo, I. S.; Song, L.; Liu, M.

2003-01-01T23:59:59.000Z

169

E-Print Network 3.0 - alluvial fan sedimentation Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

alluvial fans commonly occur with little to no warning, and have high velocities and sediment... with little warning, travel at high speeds, and carry massive amounts of sediment...

170

E-Print Network 3.0 - alluvial fans cyprus Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

will only be useful for agricultural... constructed an expansive alluvial fan in the Konya plain. The larger mound of atalhyk-East has 12 major... Europe, Anatolia,...

171

Air-bridge microcavities Pierre R. Villeneuve, Shanhui Fan, and J. D. Joannopoulos  

E-Print Network [OSTI]

Air-bridge microcavities Pierre R. Villeneuve, Shanhui Fan, and J. D. Joannopoulos Department structures with micron-sized features using semiconductor materials. © 1995 American Institute of Physics

Fan, Shanhui

172

Qualification of Fan Generated Duct Rumble Noise: Part 2: Results (RP 1219)  

E-Print Network [OSTI]

represented the closest to the ideal configuration. REMOVING TONES In the cases where the sound levels were low, tones enter- ing the sound measurements from the fan and motor vibration were a concern. This issue was remedied by removing the tones from... is not permitted without ASHRAE’s prior written permission. ESL-PA-08-06-09 Published in ASHRAE Transactions Vol. 114, Part 2 36 ASHRAE Transactions 3. Redesign the fan and motor support structure to reduce vibration. 4. Study additional fans and select fans...

Kading, J.; Mann, A.; Pate, M.B.

173

Characterization of dynamic change of Fan-delta reservoir properties in water-drive development  

SciTech Connect (OSTI)

Fan-delta reservoir in Huzhuangji oil field of east China, is a typical highly heterogeneous reservoir. The oil field has been developed by water-drive for 10 years, but the oil recovery is less than 12%, and water cut is over 90%, resulting from high heterogeneity and serious dynamic change of reservoir properties. This paper aims at the study of dynamic change of reservoir properties in water-drive development. Through quantitative imaging analysis and mercury injection analysis of cores from inspection wells, the dynamic change of reservoir pore structure in water-drive development was studied. The results show that the {open_quotes}large pore channels{close_quotes} develop in distributary channel sandstone and become larger in water-drive development, resulting in more serious pore heterogeneity. Through reservoir sensitivity experiments, the rock-fluid reaction in water-drive development is studied. The results show the permeability of some distal bar sandstone and deserted channel sandstone becomes lower due to swelling of I/S clay minerals in pore throats. OD the other hand, the permeability of distributary channel and mouth bar sandstone become larger because the authigenic Koalinites in pore throats are flushed away with the increase of flow rate of injection water. Well-logging analysis of flooded reservoirs are used to study the dynamic change of reservoir properties in various flow units. The distribution of remaining oil is closely related to the types and distribution of flow units.

Wu Shenghe; Xiong Qihua; Liu Yuhong [Univ. of Petroleum Changping, Beijing (China)

1997-08-01T23:59:59.000Z

174

Measured Natural Cooling Enhancement of a While House Fan  

E-Print Network [OSTI]

and with the fan at the low speed and high speed settings averaged 12.1, 53.8 and 75.0 feet per minute (fpm), respectively. The analogous values for the center of the living room were 6.7, 44.0 and 54.8 fpm. Velocities measured near open windows were more than... twice the above values. Increased air velocities can have a very beneficial effect on comfort at high temperature conditions. Fanger's Predicted Mean Vote (PMV) for comfort shows a very large influence for air velocities between 0 and 100 fpm (12...

Parker, D. S.

1994-01-01T23:59:59.000Z

175

Cooling with a Whole House Fan | Department of Energy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-Series to User GroupInformationE-Gov ContactsContractOfficeCoolWhy Do FansCooling

176

List of Ceiling Fan Incentives | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpInc Place:KeystoneSolar (Texas) JumpEventBoilersCeiling Fan

177

Photo of the Week: Fan-tastic | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department ofT ib l L d F SSalesOE0000652GrowE-mail on August 24,A Driving ForceFan-tastic

178

ASRAC Fans and Blower Working Group Creation Notice of Intent  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustionImprovement3 Beryllium-Associated6-05.pdf AL2006-05.pdfAMI SystemNEUPChallenges |fans and

179

Fan System Assessment Tool Fact Sheet | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeat PumpRecord ofESPCofConstructionofFYOxideof EnergyFactDepartmentFact Sheet Fan

180

Fan System Assessment Tool Introduction | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review:Department ofDistribution Infrastructure | Department of Energy AnFan System

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Property:Building/SPElectrtyUsePercFans | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformationInyo County, California | OpenInformation MiscSPElectrtyUsePercFans Jump to:

182

Potential Global Benefits of Improved Ceiling Fan Energy Efficiency  

E-Print Network [OSTI]

2011). ENERGY STAR Unit Shipment and Market Penetration2012c. ENERGY STAR Unit Shipment and Market Penetration7 and Figure 8 show ENERGY STAR market data for qualifying

Sathaye, Nakul

2014-01-01T23:59:59.000Z

183

The Spacing of Ceiling Fans for Human Comfort in Warm Temperature Conditions  

E-Print Network [OSTI]

Airspeed tests of a commercially popular 52 in. ceiling fan operating at a low speed of 155 fpm provided sufficient airspeed for comfort to 82F in an average floor area of 97.2 ft^2 beneath the fan. When operating at maximum speed, the average floor...

Spain, S.

1987-01-01T23:59:59.000Z

184

A COMPUTATIONAL AND EXPERIMENTAL ANALYSIS OF A DUCTED FAN USED IN VTOL UAV SYSTEMS  

E-Print Network [OSTI]

conditions. Fan rotor field including secondary flows, tip vortices, blade boundary layers and the wake sys wind tunnel test data. Total pressure measurements and computational predictions of mean flow field shows a significant level of 3D hub separation affecting the overall performance of the ducted fan

Camci, Cengiz

185

Energy Efficient Single Stack Exhaust Fan Systems (E3S3F)  

E-Print Network [OSTI]

This paper first investigates the fan energy performance of a constant air volume exhaust system. Two single stack energy efficient exhaust fan systems (E3S3F) are presented. The E3S3F-I has the static pressure sensor located at the inlet...

Wang, G.; Liu, M.

2001-01-01T23:59:59.000Z

186

University of Nevada Las Vegas Arduino Project Report: Fan Speed Control as a Function of Thermistor  

E-Print Network [OSTI]

University of Nevada Las Vegas Arduino Project Report: Fan Speed Control as a Function, and an arduino board. The arduino board is programmed to read the analog input, the thermistor, and respond by the arduino that will decrease the speed of the fan. Furthermore, if the temperature goes up, the resistance

Kachroo, Pushkin

187

Inlet swirl distortion effects on the generation and propagation of fan rotor shock noise  

E-Print Network [OSTI]

A body-force-based fan model for the prediction of multiple-pure-tone noise generation is developed in this thesis. The model eliminates the need for a full-wheel, three-dimensional unsteady RANS simulation of the fan blade ...

Defoe, Jeff (Jeffrey James)

2011-01-01T23:59:59.000Z

188

STATE OF CALIFORNIA HSPP/PSPP INSTALLATION; COOLING COIL AIRFLOW & FAN WATT DRAW TEST  

E-Print Network [OSTI]

STATE OF CALIFORNIA HSPP/PSPP INSTALLATION; COOLING COIL AIRFLOW & FAN WATT DRAW TEST CEC- CF-4R TESTING CF-4R-MECH-22 HSPP/PSPP Installation; Cooling Coil Airflow & Fan Watt Draw Test (Page 1 of 3) Site of a Static Pressure Probe (HSPP), and Permanently installed Static Pressure Probe (PSPP) in the supply plenum

189

STATE OF CALIFORNIA HSPP/PSPP INSTALLATION; COOLING COIL AIRFLOW & FAN WATT DRAW TEST  

E-Print Network [OSTI]

STATE OF CALIFORNIA HSPP/PSPP INSTALLATION; COOLING COIL AIRFLOW & FAN WATT DRAW TEST CEC-CF-6R/PSPP Installation; Cooling Coil Airflow & Fan Watt Draw Test (Page 1 of 3) Site Address: Enforcement Agency: Permit), and Permanently installed Static Pressure Probe (PSPP) in the supply plenum When the Certificate of Compliance (CF

190

Effect of Nozzle Geometry on Jet Noise Reduction Using Fan Flow Deflectors  

E-Print Network [OSTI]

or sideforce p = pressure q = dynamic pressure S = wedge wetted area u = mean velocity in jet plume U = nozzleEffect of Nozzle Geometry on Jet Noise Reduction Using Fan Flow Deflectors Dimitri Papamoschou of baseline nozzle shape on the ability of fan flow deflectors to reduce downward-emitted turbulent mixing

Papamoschou, Dimitri

191

Statistic inversion of multi-zone transition probability models for aquifer characterization in alluvial fans  

E-Print Network [OSTI]

Understanding the heterogeneity arising from the complex architecture of sedimentary sequences in alluvial fans is challenging. This paper develops a statistical inverse framework in a multi-zone transition probability approach for characterizing the heterogeneity in alluvial fans. An analytical solution of the transition probability matrix is used to define the statistical relationships among different hydrofacies and their mean lengths, integral scales, and volumetric proportions. A statistical inversion is conducted to identify the multi-zone transition probability models and estimate the optimal statistical parameters using the modified Gauss-Newton-Levenberg-Marquardt method. The Jacobian matrix is computed by the sensitivity equation method, which results in an accurate inverse solution with quantification of parameter uncertainty. We use the Chaobai River alluvial fan in the Beijing Plain, China, as an example for elucidating the methodology of alluvial fan characterization. The alluvial fan is divided...

Zhu, Lin; Gong, Huili; Gable, Carl; Teatini, Pietro

2015-01-01T23:59:59.000Z

192

Outdoor unit construction for an electric heat pump  

DOE Patents [OSTI]

The outdoor unit for an electric heat pump is provided with an upper portion containing propeller fan means for drawing air through the lower portion containing refrigerant coil means in the form of four discrete coils connected together in a subassembly forming a W shape, the unit being provided with four adjustable legs which are retracted in shipment, and are adjusted on site to elevate the unit to a particular height suitable for the particular location in which the unit is installed. 4 figs.

Draper, R.; Lackey, R.S.

1984-09-11T23:59:59.000Z

193

Outdoor unit construction for an electric heat pump  

DOE Patents [OSTI]

The outdoor unit for an electric heat pump is provided with an upper portion 10 containing propeller fan means 14 for drawing air through the lower portion 12 containing refrigerant coil means 16 in the form of four discrete coils connected together in a subassembly forming a W shape, the unit being provided with four adjustable legs 64 which are retracted in shipment, and are adjusted on site to elevate the unit to a particular height suitable for the particular location in which the unit is installed.

Draper, Robert (Pittsburgh, PA); Lackey, Robert S. (Pittsburgh, PA)

1984-01-01T23:59:59.000Z

194

Core-based evidence for sandy slump and sandy debris flow facies in the Pliocene and Pleistocene of the Gulf of Mexico: Implications for submarine fan models  

SciTech Connect (OSTI)

Examination of nearly 3,500 feet of conventional core from Pliocene and Pleistocene deep-water reservoirs cored in 25 wells in 8 different areas covering the eastern, central and western Gulf of Mexico reveals that the reservoirs are predominantly composed of mass-transport deposits, mainly sandy slumps and sandy debris flows (60-100% of cored intervals). Bottom-current reworked sands are common (10-50%). Of importance to existing submarine fan models is that turbidities are extremely rare (<1 % of all cores). Sedimentary features indicative of slump and debris-flow origin include sand units with sharp upper contacts, slump folds, discordant, steeply dipping layers (up to 60[degrees]), glide planes, shear zones, brecciated clasts, rafted mudstone clasts, planar clast fabric, inverse grading of clasts, and moderate-to-high matrix content (5-20 %). These reservoirs have been interpreted by others to represent turbidite-dominated basin-floor fans and slope fans of the often used sequence stratigraphic model. However, our core data do not show a dominance of turbidities. Sandy debris flows exhibit a variety of log motifs (e.g., blocky, fining-up, and coarsening-up) due to changes in concentration of midstone clasts, and a variety of internal seismic facies (e.g., parallel-continuous, irregular-discontinuous, chaotic -discontinuous, and lateral pinch out) perhaps due to changes in stacking patterns of debris flows and slumps. Classic submarine-fan models, commonly advocated for these reservoirs, may not be appropriate. We propose a slump and debris-flow, dominated slope model in which sea-floor topography and depositional freezing (i.e., plastic flows) control sand distribution and geometry. Contrary to popular belief, sandy debris flows can be thick, areally extensive, and excellent reservoirs.

Shanmugam, G. (Mobil Exploration and Producing Technical Center, Dallas, TX (United States)); Zimbrick, G. (Mobil Exploration and Producing U.S., Dallas, TX (United States))

1996-01-01T23:59:59.000Z

195

Core-based evidence for sandy slump and sandy debris flow facies in the Pliocene and Pleistocene of the Gulf of Mexico: Implications for submarine fan models  

SciTech Connect (OSTI)

Examination of nearly 3,500 feet of conventional core from Pliocene and Pleistocene deep-water reservoirs cored in 25 wells in 8 different areas covering the eastern, central and western Gulf of Mexico reveals that the reservoirs are predominantly composed of mass-transport deposits, mainly sandy slumps and sandy debris flows (60-100% of cored intervals). Bottom-current reworked sands are common (10-50%). Of importance to existing submarine fan models is that turbidities are extremely rare (<1 % of all cores). Sedimentary features indicative of slump and debris-flow origin include sand units with sharp upper contacts, slump folds, discordant, steeply dipping layers (up to 60{degrees}), glide planes, shear zones, brecciated clasts, rafted mudstone clasts, planar clast fabric, inverse grading of clasts, and moderate-to-high matrix content (5-20 %). These reservoirs have been interpreted by others to represent turbidite-dominated basin-floor fans and slope fans of the often used sequence stratigraphic model. However, our core data do not show a dominance of turbidities. Sandy debris flows exhibit a variety of log motifs (e.g., blocky, fining-up, and coarsening-up) due to changes in concentration of midstone clasts, and a variety of internal seismic facies (e.g., parallel-continuous, irregular-discontinuous, chaotic -discontinuous, and lateral pinch out) perhaps due to changes in stacking patterns of debris flows and slumps. Classic submarine-fan models, commonly advocated for these reservoirs, may not be appropriate. We propose a slump and debris-flow, dominated slope model in which sea-floor topography and depositional freezing (i.e., plastic flows) control sand distribution and geometry. Contrary to popular belief, sandy debris flows can be thick, areally extensive, and excellent reservoirs.

Shanmugam, G. [Mobil Exploration and Producing Technical Center, Dallas, TX (United States); Zimbrick, G. [Mobil Exploration and Producing U.S., Dallas, TX (United States)

1996-12-31T23:59:59.000Z

196

Field Measurement of Heating System in a Hotel Building in Harbin  

E-Print Network [OSTI]

is adopted with a 1:1 distribution of heating condensate flow and living hot water supply condensate. Considering test concurrence, high efficiency and rational personal placement, three groups are categorized which is in charge of flow test... with fan coil distributing in function area and guest rooms in low zone and radiator distributing in office rooms in high zone. All condensation water afflux in the condensate tank located at 2th underground. A simplified schematic of water system...

Zhao, T.; Zhang, J.; Li, Y.

2006-01-01T23:59:59.000Z

197

Performance characteristics of a low pressure cyclone for axial-flow fan exhausts  

E-Print Network [OSTI]

on axial-flow fan exhausts to significantly reduce particulate emissions. Average emission concentrations, cut-point diameters, PMIO emission concentrations, and fractional efficiencies from this cyclone operating at different cyclone inlet velocities...

Simpson, Shay Lynn

1996-01-01T23:59:59.000Z

198

Fan-Speed-Aware Scheduling of Data Intensive Jobs Christine S. Chan  

E-Print Network [OSTI]

of service level agreement (SLA). At the facility level, heating, ventilating and air conditioning (HVAC market servers) additionally over-provision fan subsystems to maintain a low set point. As recently

Simunic, Tajana

199

E-Print Network 3.0 - amazon fan sediments Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

provide a record of their continental provenance and of the climatic... to those for sediment currently being shed from the Andes highlands. Amazon Fan muds have 206Pb204Pb... in...

200

SPEECH NOISE ESTIMATION USING ENHANCED MINIMA CONTROLLED RECURSIVE Ningping Fan, Justinian Rosca, Radu Balan  

E-Print Network [OSTI]

, Justinian Rosca, Radu Balan Siemens Corporate Research Inc. {Ning.Fan, Justinian.Rosca, Radu.Balan}@siemens speech samples are organized as overlapped frames and each frame is transformed into spectral domain

Balan, Radu V.

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

THE SOURCE OF 3 MINUTE MAGNETOACOUSTIC OSCILLATIONS IN CORONAL FANS  

SciTech Connect (OSTI)

We use images of high spatial, spectral, and temporal resolution, obtained using both ground- and space-based instrumentation, to investigate the coupling between wave phenomena observed at numerous heights in the solar atmosphere. Analysis of 4170 A continuum images reveals small-scale umbral intensity enhancements, with diameters {approx}0.''6, lasting in excess of 30 minutes. Intensity oscillations of Almost-Equal-To 3 minutes are observed to encompass these photospheric structures, with power at least three orders of magnitude higher than the surrounding umbra. Simultaneous chromospheric velocity and intensity time series reveal an 87 Degree-Sign {+-} 8 Degree-Sign out-of-phase behavior, implying the presence of standing modes created as a result of partial wave reflection at the transition region boundary. We find a maximum waveguide inclination angle of Almost-Equal-To 40 Degree-Sign between photospheric and chromospheric heights, combined with a radial expansion factor of <76%. An average blueshifted Doppler velocity of Almost-Equal-To 1.5 km s{sup -1}, in addition to a time lag between photospheric and chromospheric oscillatory phenomena, confirms the presence of upwardly propagating slow-mode waves in the lower solar atmosphere. Propagating oscillations in EUV intensity are detected in simultaneous coronal fan structures, with a periodicity of 172 {+-} 17 s and a propagation velocity of 45 {+-} 7 km s{sup -1}. Numerical simulations reveal that the damping of the magnetoacoustic wave trains is dominated by thermal conduction. The coronal fans are seen to anchor into the photosphere in locations where large-amplitude umbral dot (UD) oscillations manifest. Derived kinetic temperature and emission measure time series display prominent out-of-phase characteristics, and when combined with the previously established sub-sonic wave speeds, we conclude that the observed EUV waves are the coronal counterparts of the upwardly propagating magnetoacoustic slow modes detected in the lower solar atmosphere. Thus, for the first time, we reveal how the propagation of 3 minute magnetoacoustic waves in solar coronal structures is a direct result of amplitude enhancements occurring in photospheric UDs.

Jess, D. B.; Mathioudakis, M.; Reardon, K. P.; Keys, P. H.; Keenan, F. P. [Astrophysics Research Centre, School of Mathematics and Physics, Queen's University Belfast, Belfast BT7 1NN (United Kingdom); De Moortel, I. [School of Mathematics and Statistics, University of St Andrews, St Andrews KY16 9SS (United Kingdom); Christian, D. J., E-mail: d.jess@qub.ac.uk [Department of Physics and Astronomy, California State University Northridge, Northridge, CA 91330 (United States)

2012-10-01T23:59:59.000Z

202

Some dynamics of carbon, nitrogen and phosphorus in the marine shelf environment of the Mississippi Fan  

E-Print Network [OSTI]

SOME DYNAMICS OF CARBON, NITROGEN AND PHOSPHORUS IN THE MARINE SHELF ENVIRONMENT OF THE MISSISSIPPI FAN A Thesis by DANIEL WAYNE ARMSTRONG Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement... for the degree of MASTER OF SCIENCE December 1974 Major Subject: Chemical Oceanography SOME DYNAMICS OF CARBON NITROGEN, AND PHOSPHORUS IN THE MARINE SHELF ENVIRONMENT OF THE MISSISSIPPI FAN A Thesis by DANIEL WAYNE ARMSTRONG Approved as to style...

Armstrong, Daniel Wayne

1974-01-01T23:59:59.000Z

203

Engine having hydraulic and fan drive systems using a single high pressure pump  

DOE Patents [OSTI]

An engine comprises a hydraulic system attached to an engine housing that includes a high pressure pump and a hydraulic fluid flowing through at least one passageway. A fan drive system is also attached to the engine housing and includes a hydraulic motor and a fan which can move air over the engine. The hydraulic motor includes an inlet fluidly connected to the at least one passageway.

Bartley, Bradley E. (Manito, IL); Blass, James R. (Bloomington, IL); Gibson, Dennis H. (Chillicothe, IL)

2000-01-01T23:59:59.000Z

204

Continuous Commissioning® of a Single Fan Dual Duct System in an Office Building  

E-Print Network [OSTI]

boxes are independent boxes, which are operated in CAV modes. The building continuous commissioning was started on June 2004. It is being commissioned following the approaches used by the Energy Systems Laboratory at Nebraska University, which... in this case include installing VFD on the supply fan and return fan, updating all terminal boxes from CAV modes into VAV modes, resetting duct static pressure and supply air temperature, optimizing outside air intake and installing VFDs on chiller...

Dong, D.; Liu, M.

2005-01-01T23:59:59.000Z

205

Implementation of the Laboratory Air Handling Unit Systems (LAHU)  

E-Print Network [OSTI]

Implementation of the Laboratory Air Handling Unit Systems (LAHU) Y. Cui Graduate Student Energy Systems Laboratory University of Nebraska-Lincoln Omaha, NE, USA M. Liu, Ph.D., P.E. Associate Professor Energy Systems Laboratory...-around coils [18, 19], the variable air volume (VAV) fume hoods [8-16] and the usage-based control devices (UBC) [17]. These measures have effectively reduced the cooling energy, preheat energy and fan power consumption, and sometime, improved indoor...

Cui, Y.; Liu, M.; Conger, K.

2003-01-01T23:59:59.000Z

206

Optimized Fan Control In Variable Air Volume HVAC Systems Using Static Pressure Resets: Strategy Selection and Savings Analysis.  

E-Print Network [OSTI]

??The potential of static pressure reset (SPR) control to save fan energy in variable air volume HVAC systems has been well documented. Current research has… (more)

Kimla, John

2010-01-01T23:59:59.000Z

207

LETTER REPORT INDEPENDENT VERIFICATION OF THE HIGH FLUX BEAM REACTOR DECOMMISSIONING PROJECT FAN HOUSE, BUILDING 704 BNL  

SciTech Connect (OSTI)

5098-LR-01-0 -LETTER REPORT INDEPENDENT VERIFICATION OF THE HIGH FLUX BEAM REACTOR DECOMMISSIONING PROJECT FAN HOUSE, BUILDING 704 BROOKHAVEN NATIONAL LABORATORY

P.C. Weaver

2010-10-22T23:59:59.000Z

208

UNIT NUMBER:  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

193 UNIT NUMBER: 197 UNIT NAME: CONCRETE RUBBLE PILE (30) REGULATORY STATUS: AOC LOCATION: Outside plant security fence, north of the plant on Big Bayou Creek on private property....

209

A study of the effect of tip clearance on propeller fan performance  

E-Print Network [OSTI]

Coefficient VI, Xf feet of Tip Clearance on Static Pressure for Given Capacity Coefficients 61 FIGURES Figure Title 1. Two Dimensional Flow through Airfoil Blade Grid 2. Velocity Diagram for an Axial Flow Fan 3. Single Stage Axial Flow Won... RIIOCR~CZi~ I OOB0 1. 0oOO I 57 possible clearance depending upon the flow conditions. Recently, Spencer hss investigated the effect of tip clearance on the performance of an axial flow pump. The findings of this thesis for axial fan confirm his...

Alam, Md. Shamsul

1959-01-01T23:59:59.000Z

210

A combined mode fatigue model for glass reinforced nylon as applied to molded engine cooling fans  

SciTech Connect (OSTI)

The use of glass reinforced nylon in fatigue inducing environments calls for a new method of stress analysis. With an engine cooling fan, both mean and vibratory stresses need to be examined. Speed cycling can cause tensile fatigue, while vibration can cause flexural fatigue. Since tensile and flexural stresses exist in the fan simultaneously, a combined mode fatigue model is needed. The proposed model is based on high cycle flexural and tensile fatigue strengths, and tensile strength. It relates measurable strain to stress using temperature dependent flexural and tensile moduli, and treats underhood temperature and desired product life as variables.

Smith, J.D.; Bennet, M.L.

1985-01-01T23:59:59.000Z

211

Qualification of Fan Generated Duct Rumble Noise: Part 1: Test Facility(RP 1219)  

E-Print Network [OSTI]

the transition duct from break in noise from the fan room. The fiberglass insulation on the inside of the box was suspended against the MDF in order to limit any vibration damping that might occur if the insula- tion touched the duct. The duct work continued... mounted to a base. The mounting base was a double steel strut that held the fan and motor assemble together. The mounting base had six vibration isolation springs that it supported by. The four corner springs were 800 lb, 1” isolation springs, the middle...

Kading, J.; Mann, A.; Pate, M.B.

212

UNIT NUMBER  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

4 UNIT NAME C-611 Underaround Diesel Tank REGULATORY STATUS: AOC LOCATION: Immediately southeast of C-611 APPROXIMATE DIMENSIONS: 1000 gallon FUNCTION: Diesel storage OPERATIONAL...

213

Seconder's discussion of "Large covariance estimation by thresholding principal orthogonal complements" by Fan, Liao  

E-Print Network [OSTI]

Professors Fan, Liao and Mincheva for the stimu- lating and thought-provoking article. The POET estimator verify this model assumption, and secondly, whether POET offers acceptable performance if the assumption from the point of view of the usability of POET: the authors warn us that POET may perform poorly if K

Fryzlewicz, Piotr

214

Provenance Collection in Reservoir Management Workflow Environments Fan Sun, Jing Zhao  

E-Print Network [OSTI]

the different applications, makes it hard to collect and integrate provenance information in reservoir manageProvenance Collection in Reservoir Management Workflow Environments Fan Sun, Jing Zhao Department to reservoir management tasks. These work- flows are data intensive in nature, and the data is derived from

Prasanna, Viktor K.

215

QPIAD: Query Processing over Incomplete Autonomous Databases Hemal Khatri Jianchun Fan Yi Chen Subbarao Kambhampati  

E-Print Network [OSTI]

QPIAD: Query Processing over Incomplete Autonomous Databases Hemal Khatri Jianchun Fan Yi Chen.khatri,jcf,yi,rao}@asu.edu Abstract Incompleteness due to missing attribute values (aka "null values") is very common in autonomous missing attributes, even if they wind up being rel- evant to a user query. Ideally we would like

Chen, Yi

216

Comparison of test particle acceleration in torsional spine and fan reconnection regimes  

SciTech Connect (OSTI)

Magnetic reconnection is a common phenomenon taking place in astrophysical and space plasmas, especially in solar flares which are rich sources of highly energetic particles. Torsional spine and fan reconnections are important mechanisms proposed for steady-state three-dimensional null-point reconnection. By using the magnetic and electric fields for these regimes, we numerically investigate the features of test particle acceleration in both regimes with input parameters for the solar corona. By comparison, torsional spine reconnection is found to be more efficient than torsional fan reconnection in an acceleration of a proton to a high kinetic energy. A proton can gain as high as 100?MeV of relativistic kinetic energy within only a few milliseconds. Moreover, in torsional spine reconnection, an accelerated particle can escape either along the spine axis or on the fan plane depending on its injection position. However, in torsional fan reconnection, the particle is only allowed to accelerate along the spine axis. In addition, in both regimes, the particle's trajectory and final kinetic energy depend on the injection position but adopting either spatially uniform or non-uniform localized plasma resistivity does not much influence the features of trajectory.

Hosseinpour, M., E-mail: hosseinpour@tabrizu.ac.ir; Mehdizade, M.; Mohammadi, M. A. [Plasma Physics Department, University of Tabriz, Tabriz (Iran, Islamic Republic of)

2014-10-15T23:59:59.000Z

217

Energy Conservation Program for Consumer Products: Test Procedures for Residential Furnaces Fans; Correction  

Broader source: Energy.gov [DOE]

On January 3, 2014 the U.S. Department of Energy (DOE) published a final rule in the Federal Register that established the test procedure for residential furnace fans. Due to drafting errors, that document inadvertently removed necessary incorporation by reference material in the Code of Federal Regulations (CFR). This final rule rectifies this error by once again adding the removed material.

218

High-amplitude reflection packets (HARPs) of the Mississippi Fan, Gulf of Mexico  

E-Print Network [OSTI]

Examination of seismic data from the deep-water Gulf of Mexico reveals the presence of High-Amplitude Reflection Packets (HARPs). An analog study conducted by the Ocean Drilling Program Leg 155 identified and described Amazon Fan HARPs as a stacked...

Francis, Jason Michael

2000-01-01T23:59:59.000Z

219

Sequence stratigraphy, facies architecture and reservoir distribution, Cretaceous lowstand fan reservoirs, Southern Basin, onshore Trinidad  

SciTech Connect (OSTI)

Thick Albian-Campanian mass-flow sandstones in the Southern Basin Trinidad were deposited within submarine canyons incised into the northern continental slope of South America and as associated down-dip basin-floor lowstand fans. The contemporaneous slope to basin-floor break lay across the Southern Basin area with turbidity current paleoflow being to the northwest. North of this paleo-slope break graded to massive, channelized, high-density turbidite sandstones occur interstratified with shaly overbank and channel abandonment deposits. A progression of depositional sub-environments from proximal through distal lowstand fan can be recognized. All fine and thin upward but can be discriminated by the occurrence of slumps, debris flows and conglomerates, the grain-size and bedding scale of sandstones and the characteristics of low-density turbidites and mudrocks. South of the paleo-slope break mass-flow deposits comprise muddy slumps and debris flows rich in granules and pebbles deposited in slope canyons. During periods of turbidity current by-pass or fan abandonment hemipelagic settling processes predominated. Reservoir distribution maps of these lowstand fans have been constructed utilizing geometric constraints, analogs and paleoslope determinations from oriented core. The interpreted canyon locations and orientations are key to the understanding of reservoir distribution on the basin-floor tract to the north: a vital component in the exploration of the basin.

Sprague, A.R.; Larue, D.K.; Faulkner, B.L. [Exxon Production Research Company, Houston, TX (United States)] [and others

1996-08-01T23:59:59.000Z

220

NATURAL HAZARDS ON ALLUVIAL FANS: THE VENEZUELA DEBRIS FLOW AND FLASH FLOOD DISASTER  

E-Print Network [OSTI]

NATURAL HAZARDS ON ALLUVIAL FANS: THE VENEZUELA DEBRIS FLOW AND FLASH FLOOD DISASTER In December Venezuela. Rainfall on December 2-3 totaled 200 millimeters (8 inches) and was followed by a major storm, Denver, Colorado, Naples, Italy, and Vargas, Venezuela. In time scales spanning thousands of years

Eaton, L. Scott

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

L1 Adaptive Control of Hysteresis in Smart Materials Xiang Fan and Ralph C. Smith  

E-Print Network [OSTI]

L1 Adaptive Control of Hysteresis in Smart Materials Xiang Fan and Ralph C. Smith Center 27695 ABSTRACT Smart materials display coupling between electrical, magnetic, thermal and elastic inherent to smart materials presents a challenge in control of these actuators/sensors. Inverse

222

Design and experimental testing of the performance of an outdoor LiBr/H{sub 2}O solar thermal absorption cooling system with a cold store  

SciTech Connect (OSTI)

A domestic-scale prototype experimental solar cooling system has been developed based on a LiBr/H{sub 2}O absorption system and tested during the 2007 summer and autumn months in Cardiff University, UK. The system consisted of a 12 m{sup 2} vacuum tube solar collector, a 4.5 kW LiBr/H{sub 2}O absorption chiller, a 1000 l cold storage tank and a 6 kW fan coil. The system performance, as well as the performances of the individual components in the system, were evaluated based on the physical measurements of the daily solar radiation, ambient temperature, inlet and outlet fluid temperatures, mass flow rates and electrical consumption by component. The average coefficient of thermal performance (COP) of the system was 0.58, based on the thermal cooling power output per unit of available thermal solar energy from the 12 m{sup 2} Thermomax DF100 vacuum tube collector on a hot sunny day with average peak insolation of 800 W/m{sup 2} (between 11 and 13.30 h) and ambient temperature of 24 C. The system produced an electrical COP of 3.6. Experimental results prove the feasibility of the new concept of cold store at this scale, with chilled water temperatures as low as 7.4 C, demonstrating its potential use in cooling domestic scale buildings. (author)

Agyenim, Francis; Knight, Ian; Rhodes, Michael [The Welsh School of Architecture, Bute Building, King Edward VII Avenue, Cardiff University, Cardiff, CF10 3NB Wales (United Kingdom)

2010-05-15T23:59:59.000Z

223

Improving Best Air Conditioner Efficiency by 20-30% through a High Efficiency Fan and Diffuser Stage Coupled with an Evaporative Condenser Pre-Cooler  

SciTech Connect (OSTI)

The Florida Solar Energy Center (FSEC) conducted a research project to improve the best residential air conditioner condenser technology currently available on the market by retrofitting a commercially-available unit with both a high efficiency fan system and an evaporative pre-cooler. The objective was to integrate these two concepts to achieve an ultra-efficient residential air conditioner design. The project produced a working prototype that was 30% more efficient compared to the best currently-available technologies; the peak the energy efficiency ratio (EER) was improved by 41%. Efficiency at the Air-Conditioning and Refrigeration Institute (ARI) standard B-condition which is used to estimate seasonal energy efficiency ratio (SEER), was raised from a nominal 21 Btu/Wh to 32 Btu/Wh.

Parker, Danny S; Sherwin, John R; Raustad, Richard

2014-04-10T23:59:59.000Z

224

UNIT NUMBER  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

6 UNIT NAME C-632-8 Sulfuric Acid Storaqe TaD REGULATORY STATUS CERCLA LOCATION Southwest of C-631 coolin location 76 APPROXIMATE DIMENSIONS 5000 Qal - FUNCTION Sulfuric acid...

225

UNIT NUMBER  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

3 C-750B Diesel UST UNIT NAME REGULATORY STATUS: AOC LOCATION: Southeast corner of C-750 APPROXIMATE DIMENSIONS: 10,000 gallon FUNCTION: Diesel storage OPERATIONAL STATUS: Removed...

226

UNIT NUMBER  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

5 UNIT NAME C-633 PCB So111 Site REGULATORY STATUS CERCLA LOCATION C-633 Transformer area (Mac location 75) APPROXIMATE DIMENSIONS I Unknown FUNCTION Soill site OPERATIONAL STATUS...

227

Finding the largest low-rank clusters with Ky Fan 2-k-norm and l1-norm  

E-Print Network [OSTI]

Mar 24, 2014 ... Abstract: We propose a convex optimization formulation with the Ky Fan 2-k-norm and l1-norm to fi nd k largest approximately rank-one ...

Xuan Vinh Doan

2014-03-24T23:59:59.000Z

228

Jasper: the Art of Exploration in Greedy Best First Search Fan Xie and Martin Mller and Robert Holte  

E-Print Network [OSTI]

Jasper: the Art of Exploration in Greedy Best First Search Fan Xie and Martin Müller and Robert restarts and randomization for better quality search. Jasper is a satisficing planner that builds on LAMA

Müller, Martin

229

Optimized Fan Control In Variable Air Volume HVAC Systems Using Static Pressure Resets: Strategy Selection and Savings Analysis  

E-Print Network [OSTI]

. As the commissioning process has begun to require the prediction of savings, knowledge of the extent to which various SPR control strategies impact fan energy has become increasingly important. This research aims to document existing SPR control strategies and utilize...

Kimla, John

2010-07-14T23:59:59.000Z

230

Temperature and humidity control during cooling and dehumidifying by compressor and evaporator fan speed variation  

SciTech Connect (OSTI)

The accurate control of temperature and relative humidity during cooling and dehumidifying air-conditioning processes may be achieved by compressor and evaporator fan speed variation. Proportional-integral-differential (PID) control methods are shown to be suitable for attaining compressor and evaporator fan speeds such that the sensible and latent components of the refrigeration system capacity equal the sensible and latent components of the system load. The feasibility of the control method has been verified experimentally. A numerical model of an environmental control system, including refrigeration, space, and PID control subsystems, has been developed. The model is suitable for determining system response to variations of PID coefficient values and to variations of system loads.

Krakow, K.I.; Lin, S.; Zeng, Z.S. [Concordia Univ., Montreal, Quebec (Canada). Dept. of Mechanical Engineering

1995-08-01T23:59:59.000Z

231

A study of the design procedure and the performance characteristics of axial exhaust fans  

E-Print Network [OSTI]

of the requirements for the degxee of %%STER OF SCIENCE IN NECHM3EEL ENGINEERIMG August, 19/9 COBTEEITS Intoroduct'o9. on o e e ~ ~ ~ ~ ~ e ~ e ~ ~ ~ ~ ~ 1 Ia Derivation of Fan Lass ~ ~ ~ ~ ~ ~ ~ ~ ~ 2 XI Description of Test Apparatus . . . . . ~. . . 7 XII... by s reversible electric motor operated by a reversing motor control switch, which is conveniently located near the Inclined manometer connected, to the pitot tube which measures the static pressure inside the plenum chamber. The followiug equipment composes...

Barker, Gilbert Hamilton

2012-06-07T23:59:59.000Z

232

On fan-shaped cold MHD winds from Keplerian accretion discs  

E-Print Network [OSTI]

We investigate under which conditions cold, fan-shaped winds can be steadily launched from thin (Keplerian) accretion discs. Such winds are magneto-centrifugal winds launched from a thin annulus in the disc, along open magnetic field lines that fan out above the disc. In principle, such winds could be found in two situations: (1) at the interface between an inner Jet Emitting Disc, which is itself powering magneto-centrifugally driven winds, and an outer standard accretion disc; (2) at the interface between an inner closed stellar magnetosphere and the outer standard accretion disc. We refer to Terminal or T-winds to the former kind and to Magnetospheric or M-winds to the latter. The full set of resistive and viscous steady state MHD equations are analyzed for the disc (the annulus), which allow us to derive general expressions valid for both configurations. We find that, under the framework of our analysis, the only source of energy able to power any kind of fan-shaped winds is the viscous transport of rotat...

Ferreira, Jonathan

2012-01-01T23:59:59.000Z

233

Experimental optimization of cooling-tower-fan control based on field data. Master's thesis  

SciTech Connect (OSTI)

Energy costs continue to play an important role in the decision-making process for building design and operation. Since the chiller, cooling tower fans, and associated pumps consume the largest fraction of energy in a heating, ventilating, and air-conditioning (HVAC) system, the control of these components is of major importance in determining building energy use. A significant control parameter for the chilled water system is the minimum entering condenser water set point temperature at which the cooling tower fans are cycled on and off, several studies have attempted to determine the optimum value for this minimum set point temperature, but direct measurements are not available to validate these studies. The purpose of this study was to experimentally determine the optimum minimum entering condenser water set point temperature from field data based on minimum energy consumption and to validate a chilled water system analytical model previously developed in earlier work. The total chiller system electrical consumption (chiller and cooling tower fan energy) was measured for four entering condensor water set point temperatures (70, 75, 80, and 85 deg F). The field results were compared to results obtained using an analytical model previously developed in a thesis entitled Optimized Design of a Commercial Building Chiller/Cooling Tower System, written by Joyce.

Herman, D.L.

1991-04-01T23:59:59.000Z

234

Design, testing and two-dimensional flow modeling of a multiple-disk fan  

SciTech Connect (OSTI)

A multiple-disk Tesla type fan has been designed, tested and analyzed two-dimensionally using the conservation of angular momentum principle. Experimental results showed that such multiple-disk fans exhibited exceptionally low performance characteristics, which could be attributed to the low viscosity, tangential nature of the flow, and large mechanical energy losses at both suction and discharge sections that are comparable to the total input power. By means of theoretical analysis, local and overall shearing stresses on the disk surfaces have been determined based on tangential and radial velocity distributions of the air flow of different volume flow rates at prescribed disk spaces and rotational speeds. Then the total power transmitted by rotating disks to air flow, and the power acquired by the air flow in the gap due to transfer of angular momentum have been obtained by numerically integrating shearing stresses over the disk surfaces. Using the measured shaft and hydraulic powers, these quantities were utilized to evaluate mechanical energy losses associated with the suction and discharge sections of the fan. (author)

Engin, Tahsin; Oezdemir, Mustafa; Cesmeci, Sevki [Department of Mechanical Engineering, The University of Sakarya, Esentepe Campus, 54187 Sakarya (Turkey)

2009-11-15T23:59:59.000Z

235

United States  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage »of EnergyTheTwo New EnergyofDEVELOPMENTEnergy 1n n d d eAlan8 United

236

Building America Case Study: Evaluating Through-Wall Air Transfer Fans, Pittsburgh, Pennsylvania (Fact Sheet)  

SciTech Connect (OSTI)

In this project, Building America team IBACOS performed field testing in a new construction unoccupied test house in Pittsburgh, Pennsylvania to evaluate heating, ventilating, and air conditioning (HVAC) distribution systems during heating, cooling, and midseason conditions. Four air-based HVAC distribution systems were assessed:-a typical airflow ducted system to the bedrooms, a low airflow ducted system to the bedrooms, a system with transfer fans to the bedrooms, and a system with no ductwork to the bedrooms. The relative ability of each system was considered with respect to relevant Air Conditioning Contractors of America and ASHRAE standards for house temperature uniformity and stability, respectively.

Not Available

2014-10-01T23:59:59.000Z

237

A study in animation and visualization: consolidation of the Mississippi Fan  

E-Print Network [OSTI]

of MASTER OF SCIENCE December 1992 Major Subject: Computer Science A STUDY IN ANIMATION AND VISUALIZATION: CONSOLIDATION OF THE MISSISSIPPI FAN A Thesis by KELLY LYNN PARMLEY Approved as to style and content by: Glen N. Williams (Chair of Committee... and effort expended, Malia Martin, Derek Spears, Debbie Carlson and Neal McDonald for help with portions of the research, and Dr. Childs, Susan Mengel, and Clay Williams for help in generating the LaTEX document. Thanks also go to Willis Marti, Donna...

Parmley, Kelly Lynn

1992-01-01T23:59:59.000Z

238

Web-based Support Systems for Sustainable Communities W.N. Liu J.T. Yao L. Fan Y.Y. Yao X.D. Yang  

E-Print Network [OSTI]

present an architecture of Web-based support systems for sustainable communities. The architectureWeb-based Support Systems for Sustainable Communities W.N. Liu J.T. Yao L. Fan Y.Y. Yao X.D. Yang,fan,yyao,yang}@cs.uregina.ca ABSTRACT This paper studies Web-based support systems for sustain- able communities. A sustainable

Yao, JingTao

239

Termination unit  

SciTech Connect (OSTI)

This invention relates to a termination unit comprising an end-section of a cable. The end section of the cable defines a central longitudinal axis and comprising end-parts of N electrical phases, an end-part of a neutral conductor and a surrounding thermally insulation envelope adapted to comprising a cooling fluid. The end-parts of the N electrical phases and the end-part of the neutral conductor each comprising at least one electrical conductor and being arranged in the cable concentrically around a core former with a phase 1 located relatively innermost, and phase N relatively outermost in the cable, phase N being surrounded by the neutral conductor, electrical insulation being arrange between neighboring electrical phases and between phase N and the neutral conductor, and wherein the end-parts of the neutral conductor and the electrical phases each comprise a contacting surface electrically connected to at least one branch current lead to provide an electrical connection: The contacting surfaces each having a longitudinal extension, and being located sequentially along the longitudinal extension of the end-section of the cable. The branch current leads being individually insulated from said thermally insulation envelope by individual electrical insulators.

Traeholt, Chresten [Frederiksberg, DK; Willen, Dag [Klagshamn, SE; Roden, Mark [Newnan, GA; Tolbert, Jerry C [Carrollton, GA; Lindsay, David [Carrollton, GA; Fisher, Paul W [Heiskell, TN; Nielsen, Carsten Thidemann [Jaegerspris, DK

2014-01-07T23:59:59.000Z

240

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

Computers and Other Electronics in U.S. Homes, by Housing Unit Type, 2009" " Million Housing Units, Final" ,,"Housing Unit Type" ,,"Single-Family Units",,"Apartments in Buildings...

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

Air Conditioning in U.S. Homes, by Housing Unit Type, 2009" " Million Housing Units, Final" ,,"Housing Unit Type" ,,"Single-Family Units",,"Apartments in Buildings With" ,"Total...

242

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

Water Heating in U.S. Homes, by Housing Unit Type, 2009" " Million Housing Units, Final" ,,"Housing Unit Type" ,,"Single-Family Units",,"Apartments in Buildings With" ,"Total...

243

VELOCITY MEASUREMENTS FOR A SOLAR ACTIVE REGION FAN LOOP FROM HINODE/EIS OBSERVATIONS  

SciTech Connect (OSTI)

The velocity pattern of a fan loop structure within a solar active region over the temperature range 0.15-1.5 MK is derived using data from the EUV Imaging Spectrometer (EIS) on board the Hinode satellite. The loop is aligned toward the observer's line of sight and shows downflows (redshifts) of around 15 km s{sup -1} up to a temperature of 0.8 MK, but for temperatures of 1.0 MK and above the measured velocity shifts are consistent with no net flow. This velocity result applies over a projected spatial distance of 9 Mm and demonstrates that the cooler, redshifted plasma is physically disconnected from the hotter, stationary plasma. A scenario in which the fan loops consist of at least two groups of 'strands'-one cooler and downflowing, the other hotter and stationary-is suggested. The cooler strands may represent a later evolutionary stage of the hotter strands. A density diagnostic of Mg VII was used to show that the electron density at around 0.8 MK falls from 3.2 Multiplication-Sign 10{sup 9} cm{sup -3} at the loop base, to 5.0 Multiplication-Sign 10{sup 8} cm{sup -3} at a projected height of 15 Mm. A filling factor of 0.2 is found at temperatures close to the formation temperature of Mg VII (0.8 MK), confirming that the cooler, downflowing plasma occupies only a fraction of the apparent loop volume. The fan loop is rooted within a so-called outflow region that displays low intensity and blueshifts of up to 25 km s{sup -1} in Fe XII {lambda}195.12 (formed at 1.5 MK), in contrast to the loop's redshifts of 15 km s{sup -1} at 0.8 MK. A new technique for obtaining an absolute wavelength calibration for the EIS instrument is presented and an instrumental effect, possibly related to a distorted point-spread function, that affects velocity measurements is identified.

Young, P. R. [College of Science, George Mason University, 4400 University Drive, Fairfax, VA 22030 (United States); O'Dwyer, B.; Mason, H. E. [Department of Applied Mathematics and Theoretical Physics, University of Cambridge, Wilberforce Road, Cambridge, CB3 0WA (United Kingdom)

2012-01-01T23:59:59.000Z

244

Stimulated Emission from a Single Excited Atom in a Waveguide Eden Rephaeli1,* and Shanhui Fan2,  

E-Print Network [OSTI]

Stimulated Emission from a Single Excited Atom in a Waveguide Eden Rephaeli1,* and Shanhui Fan2, 1; published 3 April 2012) We study stimulated emission from an excited two-level atom coupled to a waveguide by the atom, plays a very important role in stimulated emission. Additionally, the temporal duration

Fan, Shanhui

245

Performance Optimization of a Fan System- Overcoming Impacts of Modified Design Criteria Due to Regulatory Requirements and Changed Operating Conditions  

E-Print Network [OSTI]

that was applied to address fan inefficiency. Energy savings from optimizing the system are estimated to be 338 kW, nearly half of the original measured input power of 678 kW. The project is currently being implemented and will have a payback period of less than 8...

Wroblewski, R. G.; Preis, F.; Smith, R.

246

Study of the Effects of Ambient Conditions Upon the Performance of Fan Powered, Infrared Natural Gas Burners  

SciTech Connect (OSTI)

The objective of this investigation was to characterize the operation of a fan-powered, infrared burner (IR burner) at various gas compositions and ambient conditions, develop numerical model to simulate the burner performances, and provide design guidelines for appliances containing PIR burners for satisfactory performance.

Clark Atlanta University

2002-12-02T23:59:59.000Z

247

On Flame-Wall Thermal-Coupling in Micro Combustors Yong Fan, Yuji Suzuki, and Nobuhide Kasagi  

E-Print Network [OSTI]

On Flame-Wall Thermal-Coupling in Micro Combustors Yong Fan, Yuji Suzuki, and Nobuhide Kasagi Department of Mechanical Engineering, The University of Tokyo, Japan Keywords: Micro combustor, Premixed of premixed CH4/Air flame propagation and quenching in three quartz combustors with chamber depth of 0.7 mm, 1

Kasagi, Nobuhide

248

Gas-surface scattering with multiple collisions in the physisorption potential well Guoqing Fan and J. R. Manson  

E-Print Network [OSTI]

Gas-surface scattering with multiple collisions in the physisorption potential well Guoqing Fan The problem of gas-surface collisions is developed in terms of a theoretical formalism that allows calcula gas distributions are considered, a monoenergetic incident beam and an equilibrium gas appropriate

Manson, Joseph R.

249

Inferring Air Pollution by Sniffing Social Media Shike Mei, Han Li, Jing Fan, Xiaojin Zhu and Charles R. Dyer  

E-Print Network [OSTI]

Inferring Air Pollution by Sniffing Social Media Shike Mei, Han Li, Jing Fan, Xiaojin Zhu issue of air pollution in China and elsewhere in the world is to monitor it. While more physical prediction performance of our approach. I. INTRODUCTION Air pollution is a significant issue in China

Dyer, Charles R.

250

Near-infrared double negative metamaterials Shuang Zhang, Wenjun Fan, K. J. Malloy and S. R. J. Brueck  

E-Print Network [OSTI]

Near-infrared double negative metamaterials Shuang Zhang, Wenjun Fan, K. J. Malloy and S. R. J and negative over an overlapping near-infrared wavelength range resulting in a low loss negative. Brueck, "Demonstration of Near-Infrared Negative-Index Materials," Postdeadline Paper at OSA Topical

New Mexico, University of

251

Theory of Second-Harmonic Generation in Colloidal Crystals J. P. Huang,* Y. C. Jian, and C. Z. Fan  

E-Print Network [OSTI]

Theory of Second-Harmonic Generation in Colloidal Crystals J. P. Huang,* Y. C. Jian, and C. Z. Fan-Kornfeld formulation, we study the effective susceptibility of second-harmonic generation (SHG) in colloidal crystals of second-harmonic generation (SHG); that is, an input (pump) wave can generate another wave with twice

Huang, Ji-Ping

252

An optical fan for light beams for high-precision optical measurements and optical switching  

E-Print Network [OSTI]

The polarization and orbital angular momentum properties of light are of great importance in optical science and technology in the fields of high precision optical measurements and high capacity and high speed optical communications. Here we show, a totally new method, based on a combination of these two properties and using the thermal dispersion and electro-optical effect of birefringent crystals, the construction of a simple and robust scheme to rotate a light beam like a fan. Using a computer-based digital image processing technique, we determine the temperature and the thermal dispersion difference of the crystal with high resolution. We also use the rotation phenomenon to realize thermo-optic and electro-optic switches. The basic operating principles for measurement and switching processes are presented in detail. The methods developed here will have wide practical applicability in various fields, including remote sensing, materials science and optical communication networks.

Zhi-Yuan Zhou; Yan Li; Dong-Sheng Ding; Yun-Kun Jiang; Wei Zhang; Shuai Shi; Bao-Sen Shi; Guang-Can Guo

2014-05-08T23:59:59.000Z

253

Verifying energy savings with minimal metered data: The Hunter heat pump analysis  

SciTech Connect (OSTI)

In November 1992, Hunter Army Air Field (AAF) completed the installation of 489 air-source heat pumps -- a new heat pump and air-handling unit for each residence. The air-source heat pumps replaced older, less efficient, air-conditioning systems, fuel oil-fired furnaces, and fan coil units. Hunter AAF originally contacted to upgrade the old family housing heating, ventilating, and air-conditioning (HVAC) systems with high efficiency air-conditioning systems and natural gas furnaces, but an alternative proposal and following energy studies indicated that heat pumps were a more life-cycle cost-effective alternative. Six months after the heat pumps were installed, Hunter`s energy bills appeared to be increasing, not decreasing as expected. In early 1994, Pacific Northwest Laboratory` (PNL) began an analysis to determine if there were any energy savings resulting from the heat pump installation as predicted by previous energy studies. The problem is that the HVAC systems are not specifically submetered to support verifying the resulting energy savings and, as is the case with most federal facilities, even the homes are not individually metered. Savings verification needed to be accomplished with die existing and available metered data. This data consisted primarily of monthly electric submeter readings from the two housing subdivision meters, historical fuel oil delivery records for family housing, and monthly base-wide electric bills. The objective of the study is to verify the change in energy consumption in family housing and, to the extent possible, identify how much of the change in consumption is attributable to the new HVAC system and how much is probably attributable to other factors, such as the weather.

Parker, S.A.

1995-03-01T23:59:59.000Z

254

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

2 Computers and Other Electronics in U.S. Homes, by OwnerRenter Status, 2009" " Million Housing Units, Final" ,,,,"Housing Unit Type" ,,,,"Single-Family Units",,,,"Apartments in...

255

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

"Not Asked (Apartments in Buildings" "With 5 or More Units)",19.1,4.4,3.7,6.2,4.7 "FoundationBasement of Single-Family" "Units and Apartments in Buildings With" "2 to 4 Units...

256

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

"Not Asked (Apartments in Buildings" "With 5 or More Units)",19.1,9.6,5,2.2,1.5,0.8 "FoundationBasement of Single-Family" "Units and Apartments in Buildings With" "2 to 4 Units...

257

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

2 Air Conditioning in U.S. Homes, by OwnerRenter Status, 2009" " Million Housing Units, Final" ,,,,"Housing Unit Type" ,,,,"Single-Family Units",,,,"Apartments in Buildings With"...

258

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

2 Water Heating in U.S. Homes, by OwnerRenter Status, 2009" " Million Housing Units, Final" ,,,,"Housing Unit Type" ,,,,"Single-Family Units",,,,"Apartments in Buildings With"...

259

United States Department of  

E-Print Network [OSTI]

Gifford Pinchot Drive Madison, WI #12;2 International system of units (SI conversion factors) Conversion English unit factor SI unit acre 4,046 square meter (m2 ) board foot 0.002 cubic meter (m3 ) bushel (U

260

Impacts of Static Pressure Reset on VAV System Air Leakage, Fan Power and Thermal Energy - Part I: Theoretical Model and Simulation  

E-Print Network [OSTI]

As for a variable air volume (VAV) system, the air duct static pressure is a typical control variable maintained by modulating supply fan speed. The static pressure equals to the summation of the duct pressure loss downstream of the sensor...

Liu, M.; Feng, J.; Wang, Z.; Wu, L.; Zheng, K.; Pang, W.

2007-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

A prototype fan-beam optical CT scanner for 3D dosimetry  

SciTech Connect (OSTI)

Purpose: The objective of this work is to introduce a prototype fan-beam optical computed tomography scanner for three-dimensional (3D) radiation dosimetry. Methods: Two techniques of fan-beam creation were evaluated: a helium-neon laser (HeNe, {lambda} = 543 nm) with line-generating lens, and a laser diode module (LDM, {lambda} = 635 nm) with line-creating head module. Two physical collimator designs were assessed: a single-slot collimator and a multihole collimator. Optimal collimator depth was determined by observing the signal of a single photodiode with varying collimator depths. A method of extending the dynamic range of the system is presented. Two sample types were used for evaluations: nondosimetric absorbent solutions and irradiated polymer gel dosimeters, each housed in 1 liter cylindrical plastic flasks. Imaging protocol investigations were performed to address ring artefacts and image noise. Two image artefact removal techniques were performed in sinogram space. Collimator efficacy was evaluated by imaging highly opaque samples of scatter-based and absorption-based solutions. A noise-based flask registration technique was developed. Two protocols for gel manufacture were examined. Results: The LDM proved advantageous over the HeNe laser due to its reduced noise. Also, the LDM uses a wavelength more suitable for the PRESAGE{sup TM} dosimeter. Collimator depth of 1.5 cm was found to be an optimal balance between scatter rejection, signal strength, and manufacture ease. The multihole collimator is capable of maintaining accurate scatter-rejection to high levels of opacity with scatter-based solutions (T < 0.015%). Imaging protocol investigations support the need for preirradiation and postirradiation scanning to reduce reflection-based ring artefacts and to accommodate flask imperfections and gel inhomogeneities. Artefact removal techniques in sinogram space eliminate streaking artefacts and reduce ring artefacts of up to {approx}40% in magnitude. The flask registration technique was shown to achieve submillimetre and subdegree placement accuracy. Dosimetry protocol investigations emphasize the need to allow gel dosimeters to cool gradually and to be scanned while at room temperature. Preliminary tests show that considerable noise reduction can be achieved with sinogram filtering and by binning image pixels into more clinically relevant grid sizes. Conclusions: This paper describes a new optical CT scanner for 3D radiation dosimetry. Tests demonstrate that it is capable of imaging both absorption-based and scatter-based samples of high opacities. Imaging protocol and gel dosimeter manufacture techniques have been adapted to produce optimal reconstruction results. These optimal results will require suitable filtering and binning techniques for noise reduction purposes.

Campbell, Warren G.; Rudko, D. A.; Braam, Nicolas A.; Jirasek, Andrew [University of Victoria, Victoria, British Columbia V8P 5C2 (Canada); Wells, Derek M. [British Columbia Cancer Agency, Vancouver Island Centre, Victoria, British Columbia V8R 6V5 (Canada)

2013-06-15T23:59:59.000Z

262

Field testing of component-level model-based fault detection methods for mixing boxes and VAV fan systems  

SciTech Connect (OSTI)

An automated fault detection and diagnosis tool for HVAC systems is being developed, based on an integrated, life-cycle, approach to commissioning and performance monitoring. The tool uses component-level HVAC equipment models implemented in the SPARK equation-based simulation environment. The models are configured using design information and component manufacturers' data and then fine-tuned to match the actual performance of the equipment by using data measured during functional tests of the sort using in commissioning. This paper presents the results of field tests of mixing box and VAV fan system models in an experimental facility and a commercial office building. The models were found to be capable of representing the performance of correctly operating mixing box and VAV fan systems and detecting several types of incorrect operation.

Xu, Peng; Haves, Philip

2002-05-16T23:59:59.000Z

263

Field demonstration of optimized variable speed compressor and condenser fan control for commercial refrigeration systems. Final report  

SciTech Connect (OSTI)

The demonstration project discussed in this report consisted of two separate programs intended to examine methods of implementing variable-frequency drives (VFDs) to increase the efficiency of supermarket refrigeration racks. The first program examined the optimum control strategy for minimizing the power consumption of medium-temperature parallel compressor racks driven by VFDs. The second program, aimed at developing the optimum control strategy for variable-speed control of supermarket condenser fans.

NONE

1997-11-01T23:59:59.000Z

264

Economic Recovery of Oil Trapped at Fan Margins Using High Angle Wells Multiple Hydraulic Fractures  

SciTech Connect (OSTI)

This project attempts to demonstrate the effectiveness of exploiting thin-layered, low-energy deposits at the distal margin of a prograding turbidite complex through the use of hydraulically fractured horizontal or high-angle wells. The combination of a horizontal or high-angle well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. A high-angle well will be drilled in the fan-margin portion of a slope-basin clastic reservoir and will be completed with multiple hydraulic-fracture treatments. Geologic modeling, reservoir characterization, and fine-grid reservoir simulation will be used to select the well location and orientation. Design parameters for the hydraulic-fracture treatments will be determined, in part, by fracturing an existing test well. Fracture azimuth will be predicted by passive seismic monitoring of a fracture-stimulation treatment in the test well using logging tools in an offset well.

Mike L. Laue

1997-10-30T23:59:59.000Z

265

ECONOMIC RECOVERY OF OIL TRAPPED AT FAN MARGINS USING HIGH ANGLE WELLS AND MULTIPLE HYDRAULIC FRACTURES  

SciTech Connect (OSTI)

This project attempts to demonstrate the effectiveness of exploiting thin-layered, low-energy deposits at the distal margin of a prograding turbidite complex through the use of hydraulically fractured horizontal or high-angle wells. The combination of a horizontal or high-angle well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. A high-angle well will be drilled in the fan-margin portion of a slope-basin clastic reservoir and will be completed with multiple hydraulic-fracture treatments. Geologic modeling, reservoir characterization, and fine-grid reservoir simulation will be used to select the well location and orientation. Design parameters for the hydraulic-fracture treatments will be determined, in part, by fracturing an existing test well. Fracture azimuth will be predicted by passive seismic monitoring of a fracture-stimulation treatment in the test well using logging tools in an offset well.

Mike L. Laue

1998-11-06T23:59:59.000Z

266

User manual for GEOCITY: a computer model for cost analysis of geothermal district-heating-and-cooling systems. Volume I. Main text  

SciTech Connect (OSTI)

The purpose of this model is to calculate the costs of residential space heating, space cooling, and sanitary water heating or process heating (cooling) using geothermal energy from a hydrothermal reservoir. The model can calculate geothermal heating and cooling costs for residential developments, a multi-district city, or a point demand such as an industrial factory or commercial building. GEOCITY simulates the complete geothermal heating and cooling system, which consists of two principal parts: the reservoir and fluid transmission system and the distribution system. The reservoir and fluid transmission submodel calculates the life-cycle cost of thermal energy supplied to the distribution system by simulating the technical design and cash flows for the exploration, development, and operation of the reservoir and fluid transmission system. The distribution system submodel calculates the life-cycle cost of heat (chill) delivered by the distribution system to the end-users by simulating the technical design and cash flows for the construction and operation of the distribution system. Geothermal space heating is assumed to be provided by circulating hot water through radiators, convectors, fan-coil units, or other in-house heating systems. Geothermal process heating is provided by directly using the hot water or by circulating it through a process heat exchanger. Geothermal space or process cooling is simulated by circulating hot water through lithium bromide/water absorption chillers located at each building. Retrofit costs for both heating and cooling applications can be input by the user. The life-cycle cost of thermal energy from the reservoir and fluid transmission system to the distribution system and the life-cycle cost of heat (chill) to the end-users are calculated using discounted cash flow analysis.

Huber, H.D.; Fassbender, L.L.; Bloomster, C.H.

1982-09-01T23:59:59.000Z

267

Uranium-series comminution ages of continental sediments: Case study of a Pleistocene alluvial fan  

SciTech Connect (OSTI)

Obtaining quantitative information about the timescales associated with sediment transport, storage, and deposition in continental settings is important but challenging. The uranium-series comminution age method potentially provides a universal approach for direct dating of Quaternary detrital sediments, and can also provide estimates of the sediment transport and storage timescales. (The word"comminution" means"to reduce to powder," reflecting the start of the comminution age clock as reduction of lithic parent material below a critical grain size threshold of ~;;50 mu m.) To test the comminution age method as a means to date continental sediments, we applied the method to drill-core samples of the glacially-derived Kings River Fan alluvial deposits in central California. Sediments from the 45 m core have independently-estimated depositional ages of up to ~;;800 ka, based on paleomagnetism and correlations to nearby dated sediments. We characterized sequentially-leached core samples (both bulk sediment and grain size separates) for U, Nd, and Sr isotopes, grain size, surface texture, and mineralogy. In accordance with the comminution age model, where 234U is partially lost from small sediment grains due to alpha recoil, we found that (234U/238U) activity ratios generally decrease with age, depth, and specific surface area, with depletions of up to 9percent relative to radioactive equilibrium. The resulting calculated comminution ages are reasonable, although they do not exactly match age estimates from previous studies and also depend on assumptions about 234U loss rates. The results indicate that the method may be a significant addition to the sparse set of available tools for dating detrital continental sediments, following further refinement. Improving the accuracy of the method requires more advanced models or measurements for both the recoil loss factor fa and weathering effects. We discuss several independent methods for obtaining fa on individual samples that may be useful for future studies.

Lee, Victoria E.; DePaolo, Donald J.; Christensen, John N.

2010-04-30T23:59:59.000Z

268

ECONOMIC RECOVERY OF OIL TRAPPED AT FAN MARGINS USING HIGH ANGLE WELLS AND MULTIPLE HYDRAULIC FRACTURES  

SciTech Connect (OSTI)

This project attempts to demonstrate the effectiveness of exploiting thin-layered, low-energy deposits at the distal margin of a prograding turbidite complex through the use of hydraulically fractured horizontal or high-angle wells. The combination of a horizontal or high-angle well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. A high-angle well will be drilled in the fan-margin portion of a slope-basin clastic reservoir and will be completed with multiple hydraulic-fracture treatments. Geologic modeling, reservoir characterization, and fine-grid reservoir simulation will be used to select the well location and orientation. Design parameters for the hydraulic-fracture treatments will be determined, in part, by fracturing an existing test well. Fracture azimuth will be predicted by passive seismic monitoring of a fracture-stimulation treatment in the test well using logging tools in an offset well. The long radius, near horizontal well was drilled during the first quarter of 1996. Well conditions resulted in the 7 in. production liner sticking approximately 900 ft off bottom. Therefore, a 5 in. production liner was necessary to case this portion of the target formation. Swept-out sand intervals and a poor cement bond behind the 5 in. liner precluded two of the three originally planned hydraulic fracture treatments. As a result, all pay intervals behind the 5 in. liner were perforated and stimulated with a non-acid reactive fluid. Following a short production period, the remaining pay intervals in the well (behind the 7 in. liner) were perforated. The well was returned to production to observe production trends and pressure behavior and assess the need to stimulate the new perforations.

Mike L. Laue

2001-09-28T23:59:59.000Z

269

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

,"Total U.S.1 (millions)" ,," Detached"," Attached"," 2 to 4 Units","5 or More Units","Mobile Homes" "Televisions" "Total Homes",113.6,71.8,6.7,9,19.1,6.9 "Televisions" "Number of...

270

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

in Buildings With" ,,,,"Detached",,"Attached",,"2 to 4 Units",,"5 or More Units",,"Mobile Homes" ,"Total U.S.1 (millions)" "Fuels Used and End Uses",,"Own","Rent","Own","Rent",...

271

Issuance 2014-11-21:Energy Efficiency Program for Consumer Products: Energy Conservation Standards for Ceiling Fans: Availability of the Preliminary Technical Support Document, Notice of Comment Period Extension  

Broader source: Energy.gov [DOE]

Energy Efficiency Program for Consumer Products: Energy Conservation Standards for Ceiling Fans: Availability of the Preliminary Technical Support Document, Notice of Comment Period Extension

272

Unit Testing Discussion C  

E-Print Network [OSTI]

Unit Testing Discussion C #12;Unit Test public Method is smallest unit of code Input/output transformation Test if the method does what it claims Not exactly black box testing #12;Test if (actual result Expected Computed Input #12;Functionality Computation ­ Easy to test Time based Asynchronous interaction

Massachusetts at Amherst, University of

273

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

in Buildings" "With 5 or More Units)",19.1,4.4,1,0.5,0.5,3.4,2.4,0.6,0.5 "FoundationBasement of Single-Family" "Units and Apartments in Buildings With" "2 to 4 Units...

274

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

"With 5 or More Units)",19.1,2.3,16.8,"N","N","N","N","N","N",2.3,16.8,"N","N" "FoundationBasement of Single-Family" "Units and Apartments in Buildings With" "2 to 4 Units...

275

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

in Buildings" "With 5 or More Units)",19.1,2,0.7,1.3,2.6,4.1,3.5,2.5,2.4 "FoundationBasement of Single-Family" "Units and Apartments in Buildings With" "2 to 4 Units...

276

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

"With 5 or More Units)",19.1,6.2,3.5,0.5,0.5,1.1,0.6,"Q",0.7,0.4,0.2,2,1.4,0.6 "FoundationBasement of Single-Family" "Units and Apartments in Buildings With" "2 to 4 Units...

277

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

Buildings" "With 5 or More Units)",19.1,4.7,0.9,0.4,0.3,"Q",0.6,0.4,"Q",3.8,2.9,0.9 "FoundationBasement of Single-Family" "Units and Apartments in Buildings With" "2 to 4 Units...

278

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

in Buildings" "With 5 or More Units)",19.1,3.7,2.7,0.9,0.6,0.3,0.9,1,0.2,0.6,0.2 "FoundationBasement of Single-Family" "Units and Apartments in Buildings With" "2 to 4 Units...

279

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

9 Fuels Used and End Uses in Homes in Midwest Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"Midwest Census Region" ,,,"East North Central Census...

280

United States Department of  

E-Print Network [OSTI]

., Ashland, OR 97520 and Gwyneth Myer, Consultant, 220 W. Rapp Rd. Unit 3, Talent, OR 97540. #12;2 THE FIRE

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

1 Computers and Other Electronics in Homes in West Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"West Census Region" ,,,"Mountain Census...

282

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

0 Computers and Other Electronics in Homes in South Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"South Census Region" ,,,"South Atlantic Census...

283

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

9 Computers and Other Electronics in Homes in Midwest Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"Midwest Census Region" ,,,"East North Central Census...

284

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

8 Computers and Other Electronics in Homes in Northeast Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"Northeast Census Region" ,,,"New England Census...

285

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

1 Air Conditioning in Homes in West Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"West Census Region" ,,,"Mountain Census Division",,,"Pacific Census...

286

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

8 Air Conditioning in Homes in Northeast Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"Northeast Census Region" ,,,"New England Census Division",,,"Middle...

287

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

0 Air Conditioning in Homes in South Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"South Census Region" ,,,"South Atlantic Census Division",,,,,,"East...

288

" Million Housing Units, Final"  

U.S. Energy Information Administration (EIA) Indexed Site

9 Air Conditioning in Homes in Midwest Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"Midwest Census Region" ,,,"East North Central Census...

289

Transmission Business Unit Manager  

Broader source: Energy.gov [DOE]

(See Frequently Asked Questions for more information). Where would I be working? Western Area Power Administration Rocky Mountain Region Transmission Services, (J7300) Transmission Busiess Unit 615...

290

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

9 Water Heating in U.S. Homes in Midwest Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"Midwest Census Region" ,,,"East North Central Census...

291

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

0 Water Heating in U.S. Homes in South Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"South Census Region" ,,,"South Atlantic Census Division",,,,,,"East...

292

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

11 Water Heating in U.S. Homes in West Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"West Census Region" ,,,"Mountain Census Division",,,"Pacific...

293

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

8 Water Heating in U.S. Homes in Northeast Region, Divisions, and States, 2009" " Million Housing Units, Final" ,,"Northeast Census Region" ,,,"New England Census...

294

Demonstrations of Integrated Advanced Rooftop Unit Controls and...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

energy and cost savings of more than 40% over the typical packaged air conditioners and heat pumps (with constant-speed supply fans) installed on commercial buildings. The...

295

Associative list processing unit  

DOE Patents [OSTI]

An associative list processing unit and method comprising employing a plurality of prioritized cell blocks and permitting inserts to occur in a single clock cycle if all of the cell blocks are not full. Also, an associative list processing unit and method comprising employing a plurality of prioritized cell blocks and using a tree of prioritized multiplexers descending from the plurality of cell blocks.

Hemmert, Karl Scott; Underwood, Keith D.

2013-01-29T23:59:59.000Z

296

United States Environmental  

E-Print Network [OSTI]

Protect Your Family From Lead in Your Home United States Environmental Protection Agency United · What you can do to protect your family · Where to go for more information Before renting or buying Family from Lead Hazards If you think your home has lead-based paint: · Don't try to remove lead

Loudon, Catherine

297

United States Department of  

E-Print Network [OSTI]

Assessment Thomas M. Quigley, Editor U.S. Department of Agriculture Forest Service Pacific Northwest Research, and Andy Wilson. Thomas M. Quigley Editor United States Department of Agriculture Forest Service United Service, Pacific Northwest Research Station. 120 p. (Quigley, Thomas M., ed.; Interior Columbia Basin

Brown, Gregory G.

298

Toward Green Systems for Cleanrooms: Energy Efficient Fan-filter Units Ming-Shan Jeng, Industrial Technology Research Institute, msjeng@itri.org.tw  

E-Print Network [OSTI]

of twenty FFUs collected from the market were tested, including thirteen 1220 mm x 610 mm (or 4 ft x 2 ft technology with architecture and natural resources. Cleanroom HVAC systems account for a large portion of energy use in cleanrooms. Improving energy efficiency of HVAC systems and their components can contribute

299

Article (LBNL-55462) submitted to A2C2 for publication in September 2004 Issue Introducing a Standard Testing Method for Fan-filter Units  

E-Print Network [OSTI]

Article (LBNL-55462) submitted to A2C2 for publication in September 2004 Issue Introducing a uniform method for testing and reporting FFU performance. Lawrence Berkeley National Laboratory (LBNL) [2] . This article describes the activities that LBNL has led in developing the standard for FFU

300

Development of a Laboratory Verified Single-Duct VAV System Model with Fan Powered Terminal Units Optimized Using Computational Fluid Dynamics  

E-Print Network [OSTI]

the harmonics generated by ECM systems. All research objectives were achieved. The CFD model, which was verified with laboratory measurements, showed the potential to identify opportunities for improvement in the design of the FPTU and accurately predicted...

Davis, Michael A.

2011-10-21T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Analytical determination of PID coefficients for temperature and humidity control during cooling and dehumidifying by compressor and evaporator fan speed variation  

SciTech Connect (OSTI)

A linearized analysis of temperature and relative humidity control using proportional-integral-differential (PID) controls to vary compressor motor speed and evaporator fan speed enables analytical determination of suitable PID coefficients. The PID coefficients are related to refrigeration system performance parameters and the volume of the conditioned space. Analytical determination of coefficients may eliminate or supplement trial-and-error methods. System response characteristics--damping ratios and periods--are related to PID coefficients, sampling intervals, performance parameters of a refrigeration system, and the volume of a conditioned space. Two control strategies are possible in order to control space temperature and relative humidity simultaneously. One strategy controls temperature by varying compressor speed and controls relative humidity by varying evaporator fan speed. The other strategy controls temperature by varying evaporator fan speed and controls relative humidity by varying compressor fan speed The first strategy was successfully implemented experimentally as well as by simulation. The second strategy was not successfully implemented due to an adverse interaction between the two control systems.

Krakow, K.I.; Lin, S.; Zeng, Z.S. [Concordia Univ., Montreal, Quebec (Canada). Dept. of Mechanical Engineering

1995-08-01T23:59:59.000Z

302

TEMPORAL MODELING OF SLIDE CHANGE IN PRESENTATION VIDEOS Quanfu Fan (1), Arnon Amir (2), Kobus Barnard (1), Ranjini Swaminathan (1) and Alon Efrat (1)  

E-Print Network [OSTI]

TEMPORAL MODELING OF SLIDE CHANGE IN PRESENTATION VIDEOS Quanfu Fan (1), Arnon Amir (2), Kobus develop a general framework to automatically match elec- tronic slides to the videos of corresponding video libraries. Our approach extends previous work that matches slides based on visual features alone

Barnard, Kobus

303

Phase-locked OH-PLIF of Oscillating Flame in Micro Channels FAN, Yong1*, SUZUKI, Yuji1, KASAGI, Nobuhide1  

E-Print Network [OSTI]

excitation lines [6]. Experimental setup of phase-locked OH-PLIF imaging has been developedPhase-locked OH-PLIF of Oscillating Flame in Micro Channels FAN, Yong1*, SUZUKI, Yuji1, KASAGI in the oscillation process are investigated with phase-locked OH-PLIF imaging technique. 2. Flame velocity Figures. 1

Kasagi, Nobuhide

304

Groundwater Reactive Transport Models, 2012, 141-159 141 Fan Zhang, Gour-Tsyh (George) Yeh, Jack C. Parker and Xiaonan Shi (Eds)  

E-Print Network [OSTI]

Groundwater Reactive Transport Models, 2012, 141-159 141 Fan Zhang, Gour-Tsyh (George) Yeh, Jack C: Reactive Flow & Transport Code for Use on Laptops to Leadership-Class Supercomputers G. E. Hammond1 , P. C, a next-generation reactive flow and transport code for modeling subsurface processes, has been designed

Mills, Richard

305

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

6 Televisions in U.S. Homes, by Climate Region, 2009" " Million Housing Units, Final" ,,"Climate Region2" ,"Total U.S.1 (millions)" ,,"Very Cold","Mixed- Humid","Mixed-Dry"...

306

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

" Million Housing Units, Final" ,,"Climate Region2" ,"Total U.S.1 (millions)" ,,"Very Cold","Mixed- Humid","Mixed-Dry" "Fuels Used and End Uses",,"Cold",,"Hot-Dry","Hot-Humid...

307

" Million Housing Units, Preliminary"  

U.S. Energy Information Administration (EIA) Indexed Site

Computers and Other Electronics in U.S. Homes, By Number of Household Members, 2009" " Million Housing Units, Preliminary" ,,"Number of Household Members" ,"Total U.S.1 (millions)"...

308

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

3 Computers and Other Electronics in U.S. Homes, by Year of Construction, 2009" " Million Housing Units, Final" ,,"Year of Construction" ,"Total U.S.1 (millions)" ,,"Before...

309

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

7 Computers and Other Electronics in U.S. Homes, by Census Region, 2009" " Million Housing Units, Final" ,,"Census Region" ,"Total U.S.1 (millions)" ,,"Northeast","Midwest","South"...

310

" Million Housing Units, Final"  

U.S. Energy Information Administration (EIA) Indexed Site

5 Computers and Other Electronics in U.S. Homes, by Household Income, 2009" " Million Housing Units, Final" ,,"Household Income" ,"Total U.S.1 (millions)",,,"Below Poverty...

311

Voltage verification unit  

DOE Patents [OSTI]

A voltage verification unit and method for determining the absence of potentially dangerous potentials within a power supply enclosure without Mode 2 work is disclosed. With this device and method, a qualified worker, following a relatively simple protocol that involves a function test (hot, cold, hot) of the voltage verification unit before Lock Out/Tag Out and, and once the Lock Out/Tag Out is completed, testing or "trying" by simply reading a display on the voltage verification unit can be accomplished without exposure of the operator to the interior of the voltage supply enclosure. According to a preferred embodiment, the voltage verification unit includes test leads to allow diagnostics with other meters, without the necessity of accessing potentially dangerous bus bars or the like.

Martin, Edward J. (Virginia Beach, VA)

2008-01-15T23:59:59.000Z

312

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

4 Air Conditioning in U.S. Homes, by Number of Household Members, 2009" " Million Housing Units, Final" ,,"Number of Household Members" ,"Total U.S.1 (millions)" ,,,,,,"5 or More...

313

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

7 Air Conditioning in U.S. Homes, by Census Region, 2009" " Million Housing Units, Final" ,,"Census Region" ,"Total U.S.1 (millions)" ,,"Northeast","Midwest","South","West" "Air...

314

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

3 Air Conditioning in U.S. Homes, by Year of Construction, 2009" " Million Housing Units, Final" ,,"Year of Construction" ,"Total U.S.1 (millions)" ,,"Before 1940","1940 to...

315

" Million Housing Units, Final"  

U.S. Energy Information Administration (EIA) Indexed Site

5 Air Conditioning in U.S. Homes, by Household Income, 2009" " Million Housing Units, Final" ,,"Household Income" ,"Total U.S.1 (millions)",,,"Below Poverty Line2" ,,"Less...

316

Associative list processing unit  

DOE Patents [OSTI]

An associative list processing unit and method comprising employing a plurality of prioritized cell blocks and permitting inserts to occur in a single clock cycle if all of the cell blocks are not full.

Hemmert, Karl Scott; Underwood, Keith D

2014-04-01T23:59:59.000Z

317

United States Environmental Protection  

E-Print Network [OSTI]

environmental problems today and building a science knowledge base necessary to manage our ecological resources wisely, understand how pollutants affect our health, and prevent or reduce environmental risksUnited States Environmental Protection Agency Hydrogeologic Framework, Ground-Water Geochemistry

318

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

3 Appliances in U.S. Homes, by Year of Construction, 2009" " Million Housing Units, Final" ,,"Year of Construction" ,"Total U.S.1 (millions)" ,,"Before 1940","1940 to 1949","1950...

319

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

3 Televisions in U.S. Homes, by Year of Construction, 2009" " Million Housing Units, Final" ,,"Year of Construction" ,"Total U.S.1 (millions)" ,,"Before 1940","1940 to 1949","1950...

320

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

3 Household Demographics of U.S. Homes, by Year of Construction, 2009" " Million Housing Units, Final" ,,"Year of Construction" ,"Total U.S.1 (millions)" ,,"Before 1940","1940 to...

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

5 Water Heating in U.S. Homes, by Household Income, 2009" " Million Housing Units, Final" ,,"Household Income" ,"Total U.S.1 (millions)",,,"Below Poverty Line2" ,,"Less than...

322

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

3 Water Heating in U.S. Homes, by Year of Construction, 2009" " Million Housing Units, Final" ,,"Year of Construction" ,"Total U.S.1 (millions)" ,,"Before 1940","1940 to...

323

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

6 Water Heating in U.S. Homes, by Climate Region, 2009" " Million Housing Units, Final" ,,"Climate Region2" ,"Total U.S.1 (millions)" ,,"Very Cold","Mixed- Humid","Mixed-Dry"...

324

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

7 Water Heating in U.S. Homes, by Census Region, 2009" " Million Housing Units, Final" ,,"Census Region" ,"Total U.S.1 (millions)" ,,"Northeast","Midwest","South","West" "Water...

325

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

4 Water Heating in U.S. Homes, by Number of Household Members, 2009" " Million Housing Units, Final" ,,"Number of Household Members" ,"Total U.S.1 (millions)" ,,,,,,"5 or More...

326

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

Housing Units, Final" ,,"Household Income" ,"Total U.S.1 (millions)",,,"Below Poverty Line2" ,,"Less than 20,000","20,000 to 39,999","40,000 to 59,999","60,000 to...

327

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

by the U.S. Department of Energy's Office of Energy and Efficiency and Renewable Energy (EERE). 3Housing units are classified as urban or rural using definitions created...

328

Name:______________________________________ _ Unit:___________________________________ Address:_ ___________________________________________________________________________  

E-Print Network [OSTI]

Poultry Name:______________________________________ _ Unit_Project_Began:_ __________________________ _ Ended:_________________________________ (Check All That Apply) Type of Project: Type of Poultry Raised: _____ Raising and Rearing Poultry _____ Commercial Egg Chickens _____ Poultry and Egg Consumer Projects

Liskiewicz, Maciej

329

Best Buys and Unit Pricing  

E-Print Network [OSTI]

This guide explains how to determine a unit price--the cost of an item based on a specific unit such as pound or ounce. Unit pricing can be used to identify foods that are the most economical....

Anding, Jenna

2000-02-02T23:59:59.000Z

330

EUV SPECTRAL LINE FORMATION AND THE TEMPERATURE STRUCTURE OF ACTIVE REGION FAN LOOPS: OBSERVATIONS WITH HINODE/EIS AND SDO/AIA  

SciTech Connect (OSTI)

With the aim of studying active region fan loops using observations from the Hinode EUV Imaging Spectrometer (EIS) and Solar Dynamics Observatory Atmospheric Imaging Assembly (AIA), we investigate a number of inconsistencies in modeling the absolute intensities of Fe VIII and Si VII lines, and address why spectroheliograms formed from these lines look very similar despite the fact that ionization equilibrium calculations suggest that they have significantly different formation temperatures: log(T{sub e} /K) = 5.6 and 5.8, respectively. It is important to resolve these issues because confidence has been undermined in their use for differential emission measure (DEM) analysis, and Fe VIII is the main contributor to the AIA 131 A channel at low temperatures. Furthermore, the strong Fe VIII 185.213 A and Si VII 275.368 A lines are the best EIS lines to use for velocity studies in the transition region, and for assigning the correct temperature to velocity measurements in the fans. We find that the Fe VIII 185.213 A line is particularly sensitive to the slope of the DEM, leading to disproportionate changes in its effective formation temperature. If the DEM has a steep gradient in the log(T{sub e} /K) = 5.6-5.8 temperature range, or is strongly peaked, Fe VIII 185.213 A and Si VII 275.368 A will be formed at the same temperature. We show that this effect explains the similarity of these images in the fans. Furthermore, we show that the most recent ionization balance compilations resolve the discrepancies in absolute intensities. With these difficulties overcome, we combine EIS and AIA data to determine the temperature structure of a number of fan loops and find that they have peak temperatures of 0.8-1.2 MK. The EIS data indicate that the temperature distribution has a finite (but narrow) width < log ({sigma}{sub Te}/K) = 5.5 which, in one detailed case, is found to broaden substantially toward the loop base. AIA and EIS yield similar results on the temperature, emission measure magnitude, and thermal distribution in the fans, though sometimes the AIA data suggest a relatively larger thermal width. The result is that both the Fe VIII 185.213 A and Si VII 275.368 A lines are formed at log(T{sub e} /K){approx} 5.9 in the fans, and the AIA 131 A response also shifts to this temperature.

Brooks, David H.; Young, Peter R. [College of Science, George Mason University, 4400 University Drive, Fairfax, VA 22020 (United States); Warren, Harry P., E-mail: dhbrooks@ssd5.nrl.navy.mil [Space Science Division, Naval Research Laboratory, Washington, DC 20375 (United States)

2011-04-01T23:59:59.000Z

331

Solving Unit Commitment by a Unit Decommitment Method  

E-Print Network [OSTI]

Solving Unit Commitment by a Unit Decommitment Method Chung-Li Tsengy,Chao-an Liz, Shmuel S. Oren x October 14, 1997 Abstract In this paper, we present an e cient and robust method for solving unit commit- ment problem using a unit decommitment method. 1 Introduction A problem that must be frequently solved

332

UNITED STATES OF AMERICA  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartment of EnergyProgram2-26 Date:CharterDepartmentDOE LM issued theUNITED STATES UNITED

333

Coupled double-layer Fano resonance photonic crystal filters with lattice-displacement Yichen Shuai, Deyin Zhao, Arvinder Singh Chadha, Jung-Hun Seo, Hongjun Yang, Shanhui Fan, Zhenqiang Ma  

E-Print Network [OSTI]

, Deyin Zhao, Arvinder Singh Chadha, Jung-Hun Seo, Hongjun Yang, Shanhui Fan, Zhenqiang Ma , and Weidong with lattice-displacement Yichen Shuai,1 Deyin Zhao,1 Arvinder Singh Chadha,1 Jung-Hun Seo,2 Hongjun Yang,1

Fan, Shanhui

334

United States Department of  

E-Print Network [OSTI]

play an important role in a national program for reducing greenhouse gas emissions. The conversion potential through conversion of nonforest land to forest land and through the management of forest lands and sinks in the United States can be identified. International treaties on greenhouse gas reduction require

335

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

lectricity",38.1,5.6,13.6,4.1,12.4,2.5 "Central Warm-Air Furnace",19.1,1.8,6.5,2.2,8,0.6 "Heat Pump",9.8,0.8,4.7,0.9,3,0.4 "Built-In Electric Units",5.7,2.4,1.6,0.3,0.2,1.2...

336

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

"Electricity",38.1,20,2.1,3.3,8.9,3.9 "Central Warm-Air Furnace",19.1,9.6,1,1.5,4.9,2 "Heat Pump",9.8,7,0.7,0.2,0.9,0.9 "Built-In Electric Units",5.7,1.9,0.3,1.1,2.3,"Q"...

337

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

"Electricity",38.1,2.4,4.6,24.2,7 "Central Warm-Air Furnace",19.1,0.3,2.3,13.7,2.9 "Heat Pump",9.8,0.4,0.6,7.5,1.3 "Built-In Electric Units",5.7,1.4,1.4,1.2,1.7 "Portable...

338

United States Department of  

E-Print Network [OSTI]

Hills National Forest uses such a habitat capability model (HABCAP), but its accuracy is largely unknown, Wildlife Biologist with Black Hills National Forest, Custer, SD 2 South Dakota State UniversityUnited States Department of Agriculture Forest Service Rocky Mountain Forest and Range Experiment

339

United States Department of  

E-Print Network [OSTI]

United States Department of Agriculture Managing Habitats for White-tailed DeerForest Service Rocky Mountain Forest and Range Experiment Station Fort Collins, Colorado 80526 General Technical Report RM-GTR-274 Black Hills and Bear Lodge Mountains of South Dakota and Wyoming Carolyn Hull Sieg and Kieth E

340

United States Department of  

E-Print Network [OSTI]

: For additional copies: U.S. FOREST SERVICE U.S. Forest Service 11 CAMPUS BLVD SUITE 200 Publications Distribution Forest, New Hampshire, began in 1932. One of the studies, still maintained today, consisted of severalUnited States Department of Agriculture Forest Service Northern Research Station Research Paper NRS

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

United States Department of  

E-Print Network [OSTI]

Station at Durham, New Hampshire. The computer program described in this publication was created usingUnited States Department of Agriculture Forest Service Northern Research Station General Technical://www.nrs.fs.fed.us/ Published by: For additional copies: U.S. FOREST SERVICE U.S. Forest Service 11 CAMPUS BLVD SUITE 200

342

United States of Agriculture  

E-Print Network [OSTI]

in wildlife management from the University of New Hampshire in 1988. She joined the Intermountain Research Station in 1993 after working for the States of New Hampshire and Wyoming on projects involving wetlandUnited States Department of Agriculture Forest Service Intermountain Research Station General

343

United States Department of  

E-Print Network [OSTI]

copies: USDA FOREST SERVICE USDA Forest Service 11 CAMPUS BLVD SUITE 200 Publications Distribution at Durham, New Hampshire; JENNIFER C. JENKINS, jjenkins@fs.fed.us, is a research foresterUnited States Department of Agriculture Forest Service Northeastern Research Station General

344

United Nations Development Programme  

E-Print Network [OSTI]

Energy Concessions: Pilot Programs 7.5. Modernising Corn Stover Use in Rural Jilin Province, China 7United Nations Development Programme Bureau for Development Policy Energy and Atmosphere Programme. #12;5 Acknowledgements 6 Notes on Authors 7 Foreword 9 Executive Summary 27 Introduction: Energy

345

United States Department of  

E-Print Network [OSTI]

are thought to contribute to carbon sequestration, including current debates on this topic. The science regarding forestry and carbon sequestration is more advanced and less controversial than that for range, land management, carbon sequestration, carbon markets, United States. #12;ii Executive Summary

346

FISHERY STATISTICS UNITED STATES  

E-Print Network [OSTI]

FISHERY STATISTICS OF THE UNITED STATES 1973 STATISTICAL DIGEST NO. 67 Prepared by STATISTICS a review of the fishery statistics for the year 1973 . These statistics include data on the volume and value of landings of fishery products, employment 1n the fish- eries, quantity of gear operated, number

347

FISHERY STATISTICS UNITED STATES  

E-Print Network [OSTI]

FISHERY STATISTICS OF THE UNITED STATES 1971 STATISTICAL DIGEST NO. 65 Prepared by STATISTICS ry statistics for the year 1971 . These statistics include data on the volume and value of landings of fishery products, employment in the fishe ries, quantity of gear operated, number of fishing craft e

348

" Million U.S. Housing Units"  

U.S. Energy Information Administration (EIA) Indexed Site

7 Air Conditioning Usage Indicators by Type of Housing Unit, 2005" " Million U.S. Housing Units" ,,"Type of Housing Unit" ,"Housing Units (millions)","Single-Family...

349

Economic recovery of oil trapped at fan margins using high angle wells and multiple hydraulic fractures. Annual report, September 28, 1995--September 27, 1996  

SciTech Connect (OSTI)

The digital fan margin in the northeast portion of the Yowlumne field contains significant reserves but is not economic to develop using verticle wells. Numerous interbedded shales and deteriorating rock properties limit producibility. In addition, extreme depths (13,000 ft) present a challenging environment for hydraulic fracturing and artificial lift. Lastly, a mature waterflood increases risk because of the uncertainty with size and location of flood fronts. This project attempts to demonstrate the effectiveness of exploiting the distal fan margin of this slope-basin clastic reservoir through the use of a high-angle well completed with multiple hydraulic-fracture treatments. The combination of a high-angle (or horizontal) well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional verticle wells while maintaining verticle communication between thin interbedded layers and the wellbore. The equivalent production rate and reserves of three verticle wells are anticipated at one-half to two-thirds the cost.

Niemeyer, B.L.

1997-09-01T23:59:59.000Z

350

Study of the effects of ambient conditions upon the performance of fan powered, infrared, natural gas burners. Quarterly technical progress report, October 1, 1996--December 31, 1996  

SciTech Connect (OSTI)

This quarterly technical progress report describes work performed under DOE Grant No. DE-FG22-94MT94011 during the period September 1, 1996 to December 31, 1996 which covers the nineth quarter of the project. The objective of this investigation is to characterize the operation of a fan powered infrared burner (IR burner) at various gas compositions and ambient conditions and develop design guidelines for appliances containing PIR burners for satisfactory performance. The fan powered infrared burner is a technology introduced more recently in the residential and commercial markets. It is a surface combustor that elevates the temperature of the burner head to a radiant condition. A variety of metallic and ceramic materials are used for the burner heads. It has been demonstrated that infrared burners produce low CO and NO{sub x} emissions in a controlled geometric space. As the environmental regulations become more stringent, infrared burners are receiving increasing interests.

Bai, T.

1997-01-01T23:59:59.000Z

351

Improved recovery from Gulf of Mexico reservoirs. Volume I (of 4): Task 1, conduct research on mud-rich submarine fans. Final report, February 14, 1995--October 13, 1996  

SciTech Connect (OSTI)

The objective for this portion of the research involved conducting field studies and laboratory investigations to develop and refine models for mud-rich submarine fan architectures used by seismic analysis and reservoir engineers. These research aspects have been presented in two papers as follows: (1) Bouma, A.H., {open_quotes}Review of Fine-Grained Submarine Fans and Turbidite Systems{close_quotes}; (2) Kirkova, J.T. and Lorenzo, J.M., {open_quotes}Synthetic Seismic Modeling of Measured Submarine Fans Sections, Case Study of the Tanqua Complex, Karoo, South Africa{close_quotes} The {open_quotes}Review of Fine-Grained Submarine Fans and Turbidite Systems{close_quotes} by Arnold Bouma discusses research targeted toward stimulating an increase in oil and gas recovery by developing new and improved geological understanding. The {open_quotes}Synthetic Seismic Modeling of Measured Submarine Fan Sections, Case Study of the Tanqua Complex, Karoo, South Africa{close_quotes} by J.T. Kirkova and J.M. Lorenso discusses the limitations of verticle resolution and how this affects the interpretation and characterization of submarine fan complexes.

Kimbrell, W.C.; Bassiouni, Z.A.; Bourgoyne, A.T.

1997-01-13T23:59:59.000Z

352

Contamination analysis unit  

DOE Patents [OSTI]

The portable Contamination Analysis Unit (CAU) measures trace quantifies of surface contamination in real time. The detector head of the portable contamination analysis unit has an opening with an O-ring seal, one or more vacuum valves and a small mass spectrometer. With the valve closed, the mass spectrometer is evacuated with one or more pumps. The O-ring seal is placed against a surface to be tested and the vacuum valve is opened. Data is collected from the mass spectrometer and a portable computer provides contamination analysis. The CAU can be used to decontaminate and decommission hazardous and radioactive surface by measuring residual hazardous surface contamination, such as tritium and trace organics It provides surface contamination data for research and development applications as well as real-time process control feedback for industrial cleaning operations and can be used to determine the readiness of a surface to accept bonding or coatings.

Gregg, Hugh R. (Livermore, CA); Meltzer, Michael P. (Livermore, CA)

1996-01-01T23:59:59.000Z

353

Contamination analysis unit  

DOE Patents [OSTI]

The portable Contamination Analysis Unit (CAU) measures trace quantities of surface contamination in real time. The detector head of the portable contamination analysis unit has an opening with an O-ring seal, one or more vacuum valves and a small mass spectrometer. With the valve closed, the mass spectrometer is evacuated with one or more pumps. The O-ring seal is placed against a surface to be tested and the vacuum valve is opened. Data is collected from the mass spectrometer and a portable computer provides contamination analysis. The CAU can be used to decontaminate and decommission hazardous and radioactive surfaces by measuring residual hazardous surface contamination, such as tritium and trace organics. It provides surface contamination data for research and development applications as well as real-time process control feedback for industrial cleaning operations and can be used to determine the readiness of a surface to accept bonding or coatings. 1 fig.

Gregg, H.R.; Meltzer, M.P.

1996-05-28T23:59:59.000Z

354

Thermal insulated glazing unit  

SciTech Connect (OSTI)

An improved insulated glazing unit is provided which can attain about R5 to about R10 thermal performance at the center of the glass while having dimensions about the same as those of a conventional double glazed insulated glazing unit. An outer glazing and inner glazing are sealed to a spacer to form a gas impermeable space. One or more rigid, non-structural glazings are attached to the inside of the spacer to divide the space between the inner and outer glazings to provide insulating gaps between glazings of from about 0.20 inches to about 0.40 inches. One or more glazing surfaces facing each thermal gap are coated with a low emissivity coating. Finally, the thermal gaps are filled with a low conductance gas such as krypton gas.

Selkowitz, Stephen E. (Piedmont, CA); Arasteh, Dariush K. (Oakland, CA); Hartmann, John L. (Seattle, WA)

1991-01-01T23:59:59.000Z

355

Thermal insulated glazing unit  

SciTech Connect (OSTI)

An improved insulated glazing unit is provided which can attain about R5 to about R10 thermal performance at the center of the glass while having dimensions about the same as those of a conventional double glazed insulated glazing unit. An outer glazing and inner glazing are sealed to a spacer to form a gas impermeable space. One or more rigid, non-structural glazings are attached to the inside of the spacer to divide the space between the inner and outer glazings to provide insulating gaps between glazings of from about 0.20 inches to about 0.40 inches. One or more glazing surfaces facing each thermal gap are coated with a low emissivity coating. Finally, the thermal gaps are filled with a low conductance gas such as krypton gas. 2 figs.

Selkowitz, S.E.; Arasteh, D.K.; Hartmann, J.L.

1988-04-05T23:59:59.000Z

356

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

.1,0.9,2.6,3.8,7,7.8,7.1,6.8 "Central Warm-Air Furnace",19.1,0.6,0.3,1,1.6,3.5,4,3.8,4.3 "Heat Pump",9.8,0.4,0.2,0.5,0.7,1.6,2,2.2,2.2 "Built-In Electric Units",5.7,0.7,0.2,0.5,0.9...

357

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

.2,7.1,4.4,2.6,1.3,3,6.8 "Central Warm-Air Furnace",19.1,4.6,5.5,3.6,2.2,1.2,0.6,1.4,3.5 "Heat Pump",9.8,1.4,2,2,1.4,1,0.6,1.3,0.9 "Built-In Electric Units",5.7,1.9,1.6,0.9,0.6,0.3...

358

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

.4,0.4,0.3,0.2,2,0.5,1.3,0.1 "Central Warm-Air Furnace",19.1,0.3,0,0,"Q",0.2,0.1,"Q","Q" "Heat Pump",9.8,0.4,"Q","Q","N",0.4,"Q",0.4,"N" "Built-In Electric Units",5.7,1.4,0.3,0.2,0...

359

" Million Housing Units, Final...  

U.S. Energy Information Administration (EIA) Indexed Site

ctricity",38.1,11.7,11.7,5.9,5.1,3.8 "Central Warm-Air Furnace",19.1,5.6,5.5,3.2,2.7,2.2 "Heat Pump",9.8,2.5,3.7,1.6,1.3,0.7 "Built-In Electric Units",5.7,2.4,1.7,0.6,0.7,0.4...

360

Solar heating, cooling, and domestic hot water system installed at Kaw Valley State Bank and Trust Company, Topeka, Kansas. Final report  

SciTech Connect (OSTI)

The building has approximately 5600 square feet of conditioned space. Solar energy is used for space heating, space cooling, and preheating domestic hot water (DHW). The solar energy system has an array of evacuated tube-type collectors with an area of 1068 square feet. A 50/50 solution of ethylene glycol and water is the transfer medium that delivers solar energy to a tube-in-shell heat exchanger that in turn delivers solar-heated water to a 1100 gallon pressurized hot water storage tank. When solar energy is insufficient to satisfy the space heating and/or cooling demand, a natural gas-fired boiler provides auxiliary energy to the fan coil loops and/or the absorption chillers. Extracts from the site files, specification references, drawings, and installation, operation and maintenance instructions are included.

None

1980-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Energy Management in Olefins Units  

E-Print Network [OSTI]

to the point where waste heat from pyrolysis generates more than enough steam to power the olefins unit recovery section. Furthermore, incorporating gas turbine driven electrical generators or process compressors adds to the utility export potential of the unit...

Wells, T. A.

1982-01-01T23:59:59.000Z

362

Decommissioning Unit Cost Data  

SciTech Connect (OSTI)

The Rocky Flats Closure Site (Site) is in the process of stabilizing residual nuclear materials, decommissioning nuclear facilities, and remediating environmental media. A number of contaminated facilities have been decommissioned, including one building, Building 779, that contained gloveboxes used for plutonium process development but did little actual plutonium processing. The actual costs incurred to decommission this facility formed much of the basis or standards used to estimate the decommissioning of the remaining plutonium-processing buildings. Recent decommissioning activities in the first actual production facility, Building 771, implemented a number of process and procedural improvements. These include methods for handling plutonium contaminated equipment, including size reduction, decontamination, and waste packaging, as well as management improvements to streamline planning and work control. These improvements resulted in a safer working environment and reduced project cost, as demonstrated in the overall project efficiency. The topic of this paper is the analysis of how this improved efficiency is reflected in recent unit costs for activities specific to the decommissioning of plutonium facilities. This analysis will allow the Site to quantify the impacts on future Rocky Flats decommissioning activities, and to develop data for planning and cost estimating the decommissioning of future facilities. The paper discusses the methods used to collect and arrange the project data from the individual work areas within Building 771. Regression and data correlation techniques were used to quantify values for different types of decommissioning activities. The discussion includes the approach to identify and allocate overall project support, waste management, and Site support costs based on the overall Site and project costs to provide a ''burdened'' unit cost. The paper ultimately provides a unit cost basis that can be used to support cost estimates for decommissioning at other facilities with similar equipment and labor costs. It also provides techniques for extracting information from limited data using extrapolation and interpolation techniques.

Sanford, P. C.; Stevens, J. L.; Brandt, R.

2002-02-26T23:59:59.000Z

363

United States Government  

Office of Legacy Management (LM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartment ofDepartment ofof EnergyYou$0.C.Green River,TheEPAJ60014-90101681278 United

364

Summary Max Total Units  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage »of Energy Strain Rate4 Recovery Act/BuySummary Max Total Units *If All

365

UNITED STATES OF AMERICA  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartment of EnergyProgram2-26 Date:CharterDepartmentDOE LM issued theUNITED STATES

366

l UNITED STATES GOVERNMENT  

Office of Legacy Management (LM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarlyEnergyDepartment ofDepartment ofof EnergyYou$0.C. 20545 OCTTO:March_ ,' .' ft. n.-_ ._UNITED

367

UNITED STATES OF AMERICA  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage »of EnergyTheTwo New Energyof Energy8, UNITED STATES DEPARTMENT

368

FISHERY STATISTICS E UNITED STATES  

E-Print Network [OSTI]

SH 11 .A443X FISH FISHERY STATISTICS E UNITED STATES ^ 1951 &ch 3. \\§^ ^/'· m:^ STATISTICAL DIGEST. Farley, Director Statistical Digest 30 FISHERY STATISTICS OF THE UNITED STATES 1951 BY A. W. ANDERSON;Fishery Statistics of the United States and Alaska are compiled and published annually to make available

370

2013 Reporting Unit Codes | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

2013 Reporting Unit Codes 2013 Reporting Unit Codes CFC Reporting Unit Codes 2013.pdf More Documents & Publications EA-0372: Final Environmental Assessment Alignment: Achieving...

371

2014-10-27 Issuance: Energy Conservation Standards for Ceiling Fan Light Kits; Notice of Public Meeting and Availability of the Preliminary Technical Support Document  

Broader source: Energy.gov [DOE]

This document is a pre-publication Federal Register notice of public meeting and availability of the preliminary technical support document regarding energy conservation standards for ceiling fan light kits, as issued by the Deputy Assistant Secretary for Energy Efficiency on October 27, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

372

2014-09-16 Issuance: Energy Conservation Standards for Ceiling Fans; Notice of Public Meeting and Availability of Preliminary Technical Support Document  

Broader source: Energy.gov [DOE]

This document is a pre-publication Federal Register notice of public meeting and availability of preliminary technical support document regarding energy conservation standards for ceiling fans, as issued by the Deputy Assistant Secretary on September 16, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

373

2014-12-31 Issuance: Energy Conservation Standards for Commercial and Industrial Fans and Blowers; Extension of Comment Period for Notice of Data Availability  

Broader source: Energy.gov [DOE]

This document is a pre-publication Federal Register extension of comment period for notice of data availability regarding energy conservation standards for commercial and industrial fans and blowers, as issued by the Deputy Assistant Secretary for Energy Efficiency on December 31, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

374

UNIT NUMBER SWMU 175 UNIT NAME: Concrete Rubble Pile (28...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

75 UNIT NAME: Concrete Rubble Pile (28) REGULATORY STATUS: AOC LOCATION: Outside Security Fence, East of C-360 Building in KPDES Outfall Ditch 002. APPROXIMATE DIMENSIONS: 400 ft...

375

Museum Fan Downloads  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ted Hall Atmospheric Testing icons Nevada Pacific, Pacific, Nevada Test Site Eniwetok Bikini Test Site Charlie Mike Bravo Hornet Charlie Mike Bravo Hornet Oct 30, '51 Oct 31, '52...

376

UNITED STATES DEPARTMENT OF THE INTERIOR U.s. FISH AND WILDLIFE SERVICE  

E-Print Network [OSTI]

Leven . Still later, in 1828, on a Ross - shire fan~ , a considerable por- tion of the r,round was caverN

377

Key note speaker 28/9: Shenggen Fan was appointed director general of the International Food Policy Research  

E-Print Network [OSTI]

are most effective in reducing poverty and generating agricultural growth. Before joining IFPRI, he held), and the Honor Society of Phi Kappa Phi. http://www.agra-alliance.org/ #12;Key note speaker 29/9: Bruce Campbell, Program Director, Coordinating Unit http://ccafs.cgiar.org/ Dr. Bruce Campbell has degrees in Ecology from

378

Corrective Action Management Units and Temporary Units. RCRA Information Brief  

SciTech Connect (OSTI)

On February 16, 1993 the EPA published a final rule that allows either the EPA Regional Administrator or the authorized State to designate areas as corrective action management units (CAMUs) at hazardous waste management facilities for the specific purpose of managing remediation waste that has been generated as part of the facility`s corrective action activities. According to the rule, placement of remediation wastes into or within a CAMU does not constitute land disposal of hazardous waste and is not subject to RCRA land disposal restrictions. In addition, waste disposal units located within CAMUs are not required to be designed in accordance with RCRA minimum technological requirements applicable to land disposal units. This Information Brief explains the advantages of a CAMU designation, defines a Temporary Unit (TU) and explains the advantages of a TU designation. The process for initiating a CAMU or TU designation is described for DOE sites and interim status facilities.

Not Available

1994-03-01T23:59:59.000Z

379

Advanced Unit Commitment Strategies in the United States Eastern Interconnection  

SciTech Connect (OSTI)

This project sought to evaluate the impacts of high wind penetrations on the U.S. Eastern Interconnection and analyze how different unit commitment strategies may affect these impacts.

Meibom, P.; Larsen, H. V.; Barth, R.; Brand, H.; Tuohy, A.; Ela, E.

2011-08-01T23:59:59.000Z

380

Sundue, M. A. 2011 Helechos y Lycophytas, In: Flora de la Regin del Parque Nacional Ambor, Vol. 1. Ed. M. H. Nee. Editorial FAN, Santa Cruz de la Sierra, Bolivia.  

E-Print Network [OSTI]

. Ed. M. H. Nee. Editorial FAN, Santa Cruz de la Sierra, Bolivia. Kessler, M. A. L. Moguel V., M. A and Bolivia. American Fern Journal 100. Sundue, M. A., M. B. Islam, and T. A. Ranker. 2010. Systematics Polystichum in Bolivia, with the descriptions of ten new species. Brittonia 57: 205 227. Sundue, M. A. & Prado

Barrington, David

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Second United Nations International Conference  

Office of Scientific and Technical Information (OSTI)

Second United Nations International Conference on the Peaceful Uses of Atomic Energy ON THE ANALYSIS O F BUBBLE CHAMBER TRACKS Q Hugh Bradner and F r a n k Solmitz INTRODUCTION A j...

382

United Tribes Tribal Leaders Summit  

Broader source: Energy.gov [DOE]

The United Tribes Technical College is hosting its 16th Annual Tribal Leaders Summit in Bismarck, North Dakota. This year’s theme is “Education Leading the Way to a Sustainable Tribal Development”...

383

Reduction in Unit Steam Production  

E-Print Network [OSTI]

In 2001 the company's Arch-Brandenburg facility faced increased steam costs due to high natural gas prices and decreased production due to shutdown of a process. The facility was challenged to reduce unit steam consumption to minimize the effects...

Gombos, R.

2004-01-01T23:59:59.000Z

384

PLANNING UNIT October 26, 2009  

E-Print Network [OSTI]

PLANNING UNIT October 26, 2009 Advertisement for TRIPP Chair in the Institute A large number research work in the area of Transportation Planning for control of accidents and pollution with special

Prasad, Sanjiva

385

Offshore Aquaculture in the United States  

E-Print Network [OSTI]

Offshore Aquaculture in the United States: Economic Considerations, Implications & Opportunities). 2008. Offshore Aquaculture in the United States: Economic Considerations, Implications & Opportunities;Offshore Aquaculture in the United States: Economic Considerations, Implications & Opportunities Prepared

386

Saskatchewan Instructional Development and Research Unit (SIDRU)  

E-Print Network [OSTI]

Saskatchewan Instructional Development and Research Unit (SIDRU) 25th ANNUAL REPORT 2009 2010 Saskatchewan Instructional Development & Research Unit Faculty of Education: SIDRU@uregina.ca #12; CONTENTS SASKATCHEWAN INSTRUCTIONAL DEVELOPMENT & RESEARCH UNIT

Argerami, Martin

387

Field Demonstration of a High-Efficiency Packaged Rooftop Air Conditioning Unit at Fort Gordon, Augusta, GA  

SciTech Connect (OSTI)

As part of a larger program targeting the market transformation of packaged rooftop air conditioning, five high-efficiency rooftop air conditioning products were selected in 2002 by the U.S. Department of Energy (DOE) under the Unitary Air Conditioner (UAC) Technology Procurement (http://www.pnl.gov/uac). In February 2003, Fort Gordon in Augusta, Georgia was chosen as the demonstration site. With the goal of validating the field performance and operation of one of the awarded products, a 10-ton high-efficiency packaged rooftop unit (RTU) manufactured by Global Energy Group (GEG) was installed at Fort Gordon in October 2003. Following equipment installation, power metering, air- and refrigerant-side instrumentation was installed on the GEG RTU and a 4-year old typical-efficiency 20-ton RTU manufactured by AAON . The GEG and AAON units were instrumented identically and operated May through July, 2005, to observe performance under a range of conditions. Based on the data collected as part of this demonstration, the GEG equipment performed at least 8% better in stage-1 (single compressor running) cooling and at least 16% better in stage-2 (both compressors running) than the baseline AAON equipment. Performance comparisons are based on what we call application EER normalized to equivalent specific fan power. The full-load, specific-fan-power-normalized application EERs at ARI design conditions were 10.48 Btu/Wh for the GEG and 9.00 Btu/Wh for the baseline machine. With a cost premium of nearly 50%, and slightly higher maintenance costs, the life-cycle cost analysis shows that the GEG technology pays for itself--a positive net-present value (NPV)--only in climates and buildings with long cooling seasons. Manufacture of this equipment on a larger scale can be expected to reduce costs to the point where it is more broadly cost-effective. The assumed 10-ton baseline and new-technology unit costs are $3824.00 and $5525.00 respectively. If the new technology cost is assumed to drop as sales increase to $4674.50 for a 10-ton unit (i.e. the original cost difference is halved), the life-cycle costs improve. A grid of first cost, annual maintenance cost and electricity price is enumerated and the results presented in the report show the sensitivity of life cycle cost to these three financial parameters in each of eight different climates.

Armstrong, Peter R.; Sullivan, Gregory P.; Parker, Graham B.

2006-03-31T23:59:59.000Z

388

CANADA RUSSIA UNITED KINGDOM UNITED STATES Building / Launching / Operating first ever high definition,  

E-Print Network [OSTI]

1 CANADA · RUSSIA · UNITED KINGDOM · UNITED STATES 1 #12;2 Building / Launching / Operating first

389

" Million U.S. Housing Units"  

U.S. Energy Information Administration (EIA) Indexed Site

7 Air-Conditioning Usage Indicators by Year of Construction, 2005" " Million U.S. Housing Units" ,,"Year of Construction" ,"Housing Units (millions)" ,,"Before 1940","1940 to...

390

" Million U.S. Housing Units"  

U.S. Energy Information Administration (EIA) Indexed Site

7 Air-Conditioning Usage Indicators by Number of Household Members, 2005" " Million U.S. Housing Units" ,,"Number of Households With --" ,"Housing Units (millions)" ,,"1 Member","2...

391

-UNIT NAME C-728 Motor Cleaning Facility  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

UNIT NUMBER 33 -UNIT NAME C-728 Motor Cleaning Facility -REGULATORY STATUS--3:.:::.0:..04(--u) -LOCATION North of C-720 (Map...

392

Million U.S. Housing Units Total...............................  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

Units (millions) Single-Family Units Apartments in Buildings With-- Home Electronics Usage Indicators Detached Energy Information Administration: 2005 Residential Energy...

393

" Million U.S. Housing Units"  

U.S. Energy Information Administration (EIA) Indexed Site

0 Home Appliances Usage Indicators by Year of Construction, 2005" " Million U.S. Housing Units" ,,"Year of Construction" ,"Housing Units (millions)" ,,"Before 1940","1940 to...

394

" Million U.S. Housing Units"  

U.S. Energy Information Administration (EIA) Indexed Site

5 Space Heating Usage Indicators by Year of Construction, 2005" " Million U.S. Housing Units" ,,"Year of Construction" ,"Housing Units (millions)" ,,"Before 1940","1940 to...

395

SUNY Programs: The United Kingdom  

E-Print Network [OSTI]

SUNY Programs: The United Kingdom & Ireland Semester, Academic Year and Short Term #12;1 Table of Contents How to Use This Booklet 1 Choosing a Program in the UK and Ireland 2 Exchange versus Study Abroad 3 Semester & Academic Year Programs 4 Programs in London 4 Programs outside of London 7 Programs

Suzuki, Masatsugu

396

UNITED STATES NUCLEAR REGULATORY COMMISSION  

E-Print Network [OSTI]

UNITED STATES NUCLEAR REGULATORY COMMISSION OFFICE OF NUCLEAR MATERIAL SAFETY AND SAFEGUARDS ON RADIATION THERAPY OVEREXPOSURES IN PANAMA Addressees All medical licensees. Purpose The U.S. Nuclear times resulted in significant radiation overexposures to patients. The hospital staff did not perform

397

University Assessment Contacts Academic Units  

E-Print Network [OSTI]

.j.arp@oregonstate.edu 541-737-2331 Notes: Agricultural and Resource Economics Assessment Rep: Email: Phone: Penelope DiebelUniversity Assessment Contacts Academic Units COLLEGE OF AGRICULTURAL SCIENCES Assessment Rep.Capalbo@oregonstate.edu 541-737-5639 Notes: Agricultural Education and Agricultural Sciences Assessment Rep: Email: Phone

Escher, Christine

398

United Nations on Trade and  

E-Print Network [OSTI]

by the World Summit on Sustainable Development in September 2002, the United Nations Forum on Forests on the Management, Conservation and Sustainable Development of All Types of Forests, and the relevant Chapters on the Management, Conservation and Sustainable Development of All Types of Forests; (e) Recognizing the importance

399

ABPDU - Advanced Biofuels Process Demonstration Unit  

SciTech Connect (OSTI)

Lawrence Berkeley National Lab opened its Advanced Biofuels Process Demonstration Unit on Aug. 18, 2011.

None

2011-01-01T23:59:59.000Z

400

FISHERY STATISTICS OF THE UNITED STATES  

E-Print Network [OSTI]

FISHERY STATISTICS OF THE UNITED STATES 1946 BY A. W. ANDERSON and E. A. POWER UNITED STATES GOVERNMENT Statistics of the United States, 1946 #12;FISHERY STATISTICS OF THE UNITED STATES: 1946 By A. W. ANDERSON City 129 Section 4. - Chesapeake Fisheries 131 Sectional Summaries 133 Mary I and 137 Vi rginia 140

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Organization of ISI by Divisions and Constituent Units Information Sciences Division  

E-Print Network [OSTI]

Biological Sciences Division Agricultural and Ecological Research Unit Human Genetics Unit Biological Unit Canteen Security Unit Medical Welfare Unit Telephone Unit Transport Unit Guest House Audio Visual

Bandyopadhyay, Antar

402

Reservoir description of a sand-rich submarine fan complex for a steamflood project: upper Miocene Potter sandstone, North Midway Sunset field, California  

SciTech Connect (OSTI)

Nearly 650 m of cores from the upper Miocene Potter sandstone in Mobil's Alberta/Shale property, North Midway Sunset field, California, were examined to determine depositional facies, sand-body geometry, and reservoir quality for a proposed steamflood project. The Potter represents a sand-rich submarine fan complex with braided-channel, meandering-channel, levee, and crevasse-splay facies. The braided-channel facies (gravel and coarse sand) is thick (up to 100 m), sheetlike (> 500 m wide), and highly permeable (10,000 + md). The meandering-channel facies (coarse to medium sand) is up to 20 m thick, over 400 m long, lenticular in geometry, and exhibits an upward decrease in permeability (e.g., 9000 to 500 md) related to grain size that fines upward. The levee facies (in bioturbated sand) is up to 21 m thick, shows variable geometry, and is generally low in permeability (100-1500 md). The crevasse splay (medium sand) is up to 12 m thick, sheetlike (> 300 m wide), and shows moderately high permeability (2000-8000 md). The braided-channel facies was a product of density-modified grain flows, and the remaining three facies were deposited by turbidity currents. Steam flooding of the Potter reservoir should perform extremely well because the entire reservoir is composed of relatively clean sand and the reservoir lacks both horizontal and vertical permeability barriers.

Shanmugam, G.; Clayton, C.A.

1989-03-01T23:59:59.000Z

403

Laser Doppler sensor employing a single fan-shaped interference fringe system for distance and shape measurement of laterally moving objects  

SciTech Connect (OSTI)

For monitoring the position and shape of fast moving and, especially, rotating objects such as turbo machine rotors, contactless and compact sensors with a high measurement rate as well as high precision are required. We present for the first time, to the best of our knowledge, a novel laser Doppler sensor employing a single fan-shaped interference fringe system, which allows measuring for the position and shape of fast moving solid bodies with known tangential velocity. It is shown theoretically as well as experimentally that this sensor offers concurrently high position resolution and high temporal resolution in contrast to conventional measurement techniques, since its measurement uncertainty is, in principle, independent of the object velocity. Moreover, it can be built very compact, because it features low complexity. To prove its operational capability and its potential for practical applications, radial and axial shape measurements of rotating bodies are demonstrated in comparison with triangulation. An average position resolution of about 2 {mu}m could be achieved.

Pfister, Thorsten; Buettner, Lars; Czarske, Juergen

2009-01-01T23:59:59.000Z

404

Study of the effects of ambient conditions upon the performance of fan powered, infrared, natural gas burners. Quarterly technical progress report, July 1--September 30, 1995  

SciTech Connect (OSTI)

The objective of this investigation is to characterize the operation of fan powered infrared burner (PIR) at various gas compositions and ambient conditions and develop design guidelines for appliances in containing PIR burners for satisfactory performance. During this period, experimental setup with optical and electronic instrumentation that is necessary for measuring the radiant heat output and the emission gas output of the burner has been established. The radiation measurement instrument, an FTIR, has been purchased and installed in the porous burner experimental system. The radiation measurement capability of the FTIR was tested and found to be satisfactory. A standard blackbody source, made by Graseby Infrared, was employed to calibrate the FTIR. A collection duct for emission gas measurement was fabricated and connected to the existing Horiba gas analyzer. Test runs are being conducted for flue gas analysis. A number of published research papers on modeling of porous burners were reviewed. The physical mechanism and theoretical analysis of the combustion process of the PIR burner was formulated. The numerical modeling, and implementation of a PIR burner code at CAU`s computing facility is in progress.

Bai, T.; Yeboah, Y.D.; Sampath, R.

1995-10-01T23:59:59.000Z

405

Study of the effects of ambient conditions upon the performance of fan powered, infrared, natural gas burners. Quarterly technical progress report, January 1, 1995--March 31, 1995  

SciTech Connect (OSTI)

The objective of this investigation is to characterize the operation of fan powered infrared (PIR) burner at various barometric pressures (operating altitude) and gas compositions and develop design guidelines for appliances containing PIR burners for satisfactory performance. In this program, the theoretical basis for the behavior of PIR burners will be established through analysis of the combustion, heat and mass transfer, and other related processes that determine the performance of PIR burners. Based on the results of this study, a burner performance model for radiant output will be developed. The model will be applied to predict the performance of the selected burner and will also be modified and improved through comparison with experimental results. During this period, laboratory facilities that are necessary for conducting this research are completed. The student research assistants have started working in the laboratory. The selection of the test burner has completed. The preparation and instrumentation of this test burner is underway. The theoretical analysis and modeling of the fundamental combustion process of the PIR burner is progressing well. A study of the existing models are being conducted, which will yield specific direction and recommendations for the new model to be developed.

Bai, Tiejun

1995-04-01T23:59:59.000Z

406

Study of the effects of ambient conditions upon the performance of fan powered, infrared, natural gas burners. Quarterly technical progress report, September 1--September 30, 1994  

SciTech Connect (OSTI)

The objective of this investigation is to characterize the operation of fan powered infrared(PIR) burner at various barometric pressures (operating altitude) and gas compositions and develop design guidelines for appliances containing PIR burners for satisfactory performance. In this program, the theoretical basis for the behavior of PIR burners will be established through analysis of the combustion, heat and mass transfer, and other related processes which determine the performance of PIR burners. Based on the results of this study, a first order model of the performance of the burner, including radiant output will be developed. The model will be applied to predict the performance of the selected burner and modified through comparison with test results. Concurrently, an experimental setup will be devised and built. This experimental rig will be a modified appliance, capable of measuring the heat and combustion product output, as well as providing a means by which the radiant heat output can be measured. The burner will be selected from an existing commercial appliance, a commercial deep fat fryer, and will be of a scale that will be compatible with the laboratory facilities in the Combustion Laboratory at Clark Atlanta University. Theoretical analysis and formulation of the PIR burner performance model has been started and the development of the test facilities and experimental setup has also been initiated. These are described.

Bai, T.

1994-10-01T23:59:59.000Z

407

Systems of Units Systems of units fall into three general categories (see Table 1. below)  

E-Print Network [OSTI]

in astrophysics and in particle dynamics. It is less convenient on earth, where we keep having to calculate static in English units. In industrial metric units, we still ...nd kgf /cm2 , sometimes UNITS Force Mass Accel. gc

408

The Sentara Mobile Mammography Unit | Jefferson Lab  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

The Sentara Mobile Mammography Unit The Sentara Mobile Mammography Unit will be here at Jefferson Lab on December 11, 2014 from 9 a.m.-2 p.m. Mammography detects breast cancer and...

409

Meteorological database for the United States  

E-Print Network [OSTI]

to Indoor Air Meteorological Database for the United StatesUC-402 Meteorological Database for the United States M.G.Abstract A meteorological database has been developed to aid

Apte, M.G.

2011-01-01T23:59:59.000Z

410

United Cooperative | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to:Seadov PtyInformation UC 19-6-401 et seq.NorthUniopolis, Ohio: EnergyIncJumpUnited

411

United Nations | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to:Seadov PtyInformation UC 19-6-401 et seq.NorthUniopolis, Ohio:LowPopulationUnited

412

Second United Nations International Conference  

Office of Scientific and Technical Information (OSTI)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary)morphinan antagonist Journal Article: Crystal structureComposite ForPropertiesto earthAudioSwitchSecond United

413

Compact monolithic capacitive discharge unit  

DOE Patents [OSTI]

A compact monolithic capacitive discharge unit (CDU) is disclosed in which a thyristor switch and a flyback charging circuit are both sandwiched about a ceramic energy storage capacitor. The result is a compact rugged assembly which provides a low-inductance current discharge path. The flyback charging circuit preferably includes a low-temperature co-fired ceramic transformer. The CDU can further include one or more ceramic substrates for enclosing the thyristor switch and for holding various passive components used in the flyback charging circuit. A load such as a detonator can also be attached directly to the CDU.

Roesler, Alexander W. (Tijeras, NM); Vernon, George E. (Rio Rancho, NM); Hoke, Darren A. (Albuquerque, NM); De Marquis, Virginia K. (Tijeras, NM); Harris, Steven M. (Albuquerque, NM)

2007-06-26T23:59:59.000Z

414

Efficiency United (Gas)- Commercial Efficiency Program  

Broader source: Energy.gov [DOE]

The Efficiency United Program, administered by CLEAResult Consulting, provides commercial gas incentives for the following Michigan utilities:

415

" Million U.S. Housing Units,...  

U.S. Energy Information Administration (EIA) Indexed Site

in Buildings" "With 5 or More Units)",19.1,7,5.2,3.2,1.8,0.9,0.3,0.8,4.5 "FoundationBasement of Single-Family" "Units and Apartments in Buildings With" "2 to 4 Units...

416

Municipal Solid Waste in The United States  

E-Print Network [OSTI]

2011 Facts and Figures Municipal Solid Waste in The United States #12;United States Environmental Protection Agency Office of Solid Waste (5306P) EPA530-R-13-001 May 2013 www.epa.gov #12;MUNICIPAL SOLID WASTE IN THE UNITED STATES: 2011 FACTS AND FIGURES Table of Contents Chapter Page MUNICIPAL SOLID WASTE

Barlaz, Morton A.

417

UNITED NATIONS FRAMEWORK CONVENTION ON CLIMATE CHANGE  

E-Print Network [OSTI]

UNITED NATIONS FRAMEWORK CONVENTION ON CLIMATE CHANGE UNITED NATIONS 1992 FCCC/INFORMAL/84 GE.05-62220 (E) 200705 #12;UNITED NATIONS FRAMEWORK CONVENTION ON CLIMATE CHANGE The Parties to this Convention in predictions of climate change, particularly with regard to the timing, magnitude and regional patterns thereof

Laughlin, Robert B.

418

Better Buildings Alliance, Advanced Rooftop Unit Campaign: RTU Sizing Guidance (Fact Sheet)  

SciTech Connect (OSTI)

This fact sheet discusses the causes and consequences of incorrect RTU sizing (with respect to cooling tonnage and supply fan horsepower) and points to resources that can help ensure accurate sizing calculations.

Not Available

2014-09-01T23:59:59.000Z

419

Investigation of a radiantly heated and cooled office with an integrated desiccant ventilation unit  

E-Print Network [OSTI]

Radiant heating and cooling has a reputation of increasing the comfort level and reducing the energy consumption of buildings. The main advantages of radiant heating and cooling are low operational noise and reduced fan power cost. Radiant heating...

Gong, Xiangyang

2009-05-15T23:59:59.000Z

420

Mobile inspection and repackaging unit  

SciTech Connect (OSTI)

Storage of large volumes of radioactive mixed waste (RMW) generated over the past 20 years at the Hanford Site has resulted in various waste management challenges. Presently, disposal capacity for RMW does not exist. Containers holding RMW will be stored until processing facilities can be completed to provide treatment and final disposal. Because of the complexity of these wastes, special projects have been initiated to properly manage them. This paper addresses one such project. The goal of this project is to develop a mobile inspection and repackaging unit (IRU) for solid RMW. The paper describes the structural design, equipment, ventilation system, instruments and electrical systems, video monitors and recorders, materials handling, and waste processing of containers.

Whitney, G.A.; Roberts, R.J. [Westinghouse Hanford Co., Richland, WA (United States). Solid Waste Disposal Div.

1993-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Field Demonstration of Active Desiccant Modules Designed to Integrate with Standard Unitary Rooftop Package Equipment - Final Report: Phase 3  

SciTech Connect (OSTI)

This report summarizes the investigation of two active desiccant module (ADM) pilot site installations initiated in 2001. Both pilot installations were retrofits at existing facilities served by conventional heating, ventilating, and air-conditioning (HVAC) systems that had encountered frequent humidity control, indoor air quality (IAQ), and other operational problems. Each installation involved combining a SEMCO, Inc., ADM (as described in Fischer and Sand 2002) with a standard packaged rooftop unit built by the Trane Company. A direct digital control (DDC) system integral to the ADM performed the dual function of controlling the ADM/rooftop combination and facilitating data collection, trending, and remote performance monitoring. The first installation involved providing preconditioned outdoor air to replace air exhausted from the large kitchen hood and bathrooms of a Hooters restaurant located in Rome, Georgia. This facility had previously added an additional rooftop unit in an attempt to achieve occupant comfort without success. The second involved conditioning the outdoor air delivered to each room of a wing of the Mountain Creek Inn at the Callaway Gardens resort. This hotel, designed in the ''motor lodge'' format with each room opening to the outdoors, is located in southwest Georgia. Controlling the space humidity always presented a serious challenge. Uncomfortable conditions and musty odors had caused many guests to request to move to other areas within the resort. This is the first field demonstration performed by Oak Ridge National Laboratory where significant energy savings, operating cost savings, and dramatically improved indoor environmental conditions can all be claimed as the results of a retrofit desiccant equipment field installation. The ADM/rooftop combination installed at the restaurant resulted in a reduction of about 34% in the electricity used by the building's air-conditioning system. This represents a reduction of approximately 15% in overall electrical energy consumption and a 12.5-kW reduction in peak demand. The cost of gas used for regeneration of the desiccant wheel over this period of time is estimated to be only $740, using a gas cost of $0.50 per therm--the summer rate in 2001. The estimated net savings is $5400 annually, resulting in a 1-2 year payback. It is likely that similar energy/cost savings were realized at the Callaway Gardens hotel. In this installation, however, a central plant supplied the chilled water serving fan coil units in the hotel wing retrofitted with the ADM, so it was not metered separately. Consequently, the owner could not provide actual energy consumption data specific to the facility. The energy and operating cost savings at both sites are directly attributable to higher cooling-season thermostat settings and decreased conventional system run times. These field installations were selected as an immediate and appropriate response to correct indoor humidity and fresh air ventilation problems being experienced by building occupants and owners, so no rigorous baseline-building vs. test-building energy use/operating cost savings results can be presented. The report presents several simulated comparisons between the ADM/roof HVAC approach and other equipment combinations, where both desiccant and conventional systems are modeled to provide comparable fresh air ventilation rates and indoor humidity levels. The results obtained from these simulations demonstrate convincingly the energy and operating cost savings obtainable with this hybrid desiccant/vapor-compression technology, verifying those actually seen at the pilot installations. The ADM approach is less expensive than conventional alternatives providing similar performance and indoor air quality and provides a very favorable payback (1 year or so) compared with oversized rooftop units that cannot be operated effectively with the necessary high outdoor air percentages.

Fischer, J

2004-03-15T23:59:59.000Z

422

United States Government National Nuclear Security Administration...  

Broader source: Energy.gov (indexed) [DOE]

United States Government National Nuclear Security Administration (NNSA) Savannah River Field Office (SRFO) Memorandum DATE: January 10, 2014 REPLY TO ATTN OF: sv (McAlhany,...

423

Optimization Online - Toward Scalable Stochastic Unit Commitment ...  

E-Print Network [OSTI]

May 16, 2014 ... Using a variant of the WECC-240 test case with 85 thermalgeneration units, we demonstrate the ability of our approach to solve realistic, ...

Kwok Cheung

2014-05-16T23:59:59.000Z

424

United Power- Business Energy Efficiency Rebate Program  

Broader source: Energy.gov [DOE]

United Power, in conjunction with wholesale power supplier Tri-State Generation and Transmission (TSGT), offers rebates for the installation of a variety of commercial energy efficient equipment...

425

Efficiency United (Gas)- Residential Efficiency Program  

Broader source: Energy.gov [DOE]

The Efficiency United program is intended to provide assistance and incentives to customers who employ energy efficient measures. Programs offer rebates on natural gas water heaters, clothes...

426

United States Geological Survey Geospatial Information Response  

E-Print Network [OSTI]

1 United States Geological Survey Geospatial Information Response Standard Operating Procedures May 20, 2013 Executive Summary The Geospatial, reporting requirements, and business processes for acquiring and providing geospatial

Torgersen, Christian

427

United States National Energy Technology Laboratory's (NETL)...  

Open Energy Info (EERE)

Laboratory's (NETL) Smart Grid Implementation Strategy Reference Library Website Jump to: navigation, search Tool Summary LAUNCH TOOL Name: United States National Energy Technology...

428

Problems of intraplate extensional tectonics, Western United...  

Open Energy Info (EERE)

on the Great Basin Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Proceedings: Problems of intraplate extensional tectonics, Western United...

429

Optimization Online - Toward Scalable Stochastic Unit Commitment ...  

E-Print Network [OSTI]

May 16, 2014 ... ... in stochastic unit commitment, with application to real data associated with the Independent System Operator for New England (ISO-NE).

Yonghan Feng

2014-05-16T23:59:59.000Z

430

Portable brine evaporator unit, process, and system  

DOE Patents [OSTI]

The present invention discloses a comprehensive, efficient, and cost effective portable evaporator unit, method, and system for the treatment of brine. The evaporator unit, method, and system require a pretreatment process that removes heavy metals, crude oil, and other contaminates in preparation for the evaporator unit. The pretreatment and the evaporator unit, method, and system process metals and brine at the site where they are generated (the well site). Thus, saving significant money to producers who can avoid present and future increases in transportation costs.

Hart, Paul John (Indiana, PA); Miller, Bruce G. (State College, PA); Wincek, Ronald T. (State College, PA); Decker, Glenn E. (Bellefonte, PA); Johnson, David K. (Port Matilda, PA)

2009-04-07T23:59:59.000Z

431

A report to United Services Automobile Association  

E-Print Network [OSTI]

A report to United Services Automobile Association (USAA) Submitted by Katie N. Womack Center Driving In Texas Prepared for: United Services Automobile Association (USAA) By: Katie N. Womack Center Services Automobile Association (USAA). The report documents the findings of five tasks undertaken under

432

Topaz-II reactor control unit development  

SciTech Connect (OSTI)

The development for a new digital reactor control unit for the Topaz-II reactor is described. The unit is expected to provide the means for automated control during a possible Topaz flight experiment. The breadboard design and development is discussed.

Wyant, F.J.; Jensen, D.; Logothetis, J.

1994-12-31T23:59:59.000Z

433

Saskatchewan Instructional Development & Research Unit (SIDRU)  

E-Print Network [OSTI]

Saskatchewan Instructional Development & Research Unit (SIDRU) 26th ANNUAL REPORT 2010 - 2011 Saskatchewan Instructional Development & Research Unit Faculty of Education University of Regina Regina, SK S4S 0A2 Telephone: (306) 585-5142 Fax: (306) 337-8465 E-Mail: SIDRU@uregina.ca #12;CONTENTS SASKATCHEWAN

Argerami, Martin

434

Add MTBE unit ahead of alkylation  

SciTech Connect (OSTI)

Approximately three years ago, the people at Diamond Shamrock's Sunray, Texas, refinery recognized a growing demand for high octane super premium unleaded gasoline in their regional marketing area. It was apparent that they would need to change their processing scheme to meet this growing demand. After investigating several options, they decided to install an MTBE (methyl tert-butyl ether) unit upstream of their existing sulfuric acid (H/sub 2/SO/sub 4/) aklylation unit. The new unit would process olefin feed before it entered the alkylation unit. The MTBE unit was expected to improve Diamond Shamrock's gasoline pool in two ways. First, the MTBE would be an additional high octane blending stock for the gasoline pool. Second, the MTBE unit would improve the quality of the olefin stream going to the alkylation unit. Diamond Shamrock brought their MTBE unit onstream in December, 1985. The results of the combined operation exceeded expectations, producing alkylate in excess of 98 RON (Research octane number) and MTBE of 118 RON. These components significantly upgraded the refinery's capability to produce a super premium unleaded gasoline.

Masters, K.R.; Prohaska, E.A.

1988-08-01T23:59:59.000Z

435

Total Petroleum Systems and Assessment Units (AU)  

E-Print Network [OSTI]

Total Petroleum Systems (TPS) and Assessment Units (AU) Field type Surface water Groundwater X X X X X X X X AU 00000003 Oil/ Gas X X X X X X X X Total X X X X X X X Total Petroleum Systems (TPS) and Assessment Units (AU) Field type Total undiscovered petroleum (MMBO or BCFG) Water per oil

Torgersen, Christian

436

United States Nuclear Waste Technical Review Board  

E-Print Network [OSTI]

United States Nuclear Waste Technical Review Board Experience Gained From Programs to Manage High-Level Radioactive Waste and Spent Nuclear Fuel in the United States and Other Countries A Report to Congress and the Secretary of Energy April 2011 #12;#12;U.S. Nuclear Waste Technical Review Board Experience Gained From

437

UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD  

E-Print Network [OSTI]

JEC187V3 UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 of Energy 1000 Independence Avenue, SW Washington, DC 20585 Dear Secretary O'Leary: At the Nuclear Waste UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington, VA

438

Large-Scale in the United  

E-Print Network [OSTI]

Large-Scale Offshore Wind Power in the United States ASSESSMENT OF OPPORTUNITIES AND BARRIERS, including 10% post consumer waste. #12;Large-Scale Offshore Wind Power in the United States ASSESSMENT Energy, Office of Wind and Water Power Technologies for their financial and technical support

439

Training Units and Developing Leaders Contents  

E-Print Network [OSTI]

The 2011 edition of (Field Manual) FM 7-0 reflected the Army’s unit training and leader development concepts borne from a decade of persistent combat operations. Army Doctrine Publication (ADP) 7-0, Training Units and Developing Leaders, re-establishes fundamental training and leader development concepts and processes for the U.S. Army. Training doctrine is again based on the Army’s operations and planning processes, now defined by ADP 3-0, Unified Land Operations, and ADP 5-0, The Operations Process. Mission command makes the commander responsible for unit readiness and leader development. Unit commanders must be the subject matter experts. Commanders cannot delegate oversight of unit training and leader development to subordinates. The commander’s physical presence at training sends a clear message to subordinates—unit training and leader development are the most important things the unit does when it is not actively engaged in operations. Unit training and leader development are inextricably linked. Good training supports leader development and good leaders develop good training programs for

Raymond T. Odierno

440

FISHERY STATISTICS OF THE UNITED STATES  

E-Print Network [OSTI]

STATISTICS OF THE UNITED STATES 1945 BY A. W. ANDERSON and E. A. POWER UNITED STATES GOVERNMENT PRINTING: 1945 By A. W. ANDERSON, Chief, branch of Commercial Fisheries and E. A. POWEK, Chief, Statistical at New York City ' -- Section 4. - Chesapeake Fisheries Sect ional Summari es Mary I and V i rg i n i

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Fan Systems | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGYWomentheATLANTA, GA5 &ofDepartment of Energy OnDramatic energy and cost savings

442

THE WORLD'S Biggest Fan Collection  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage »of Energy StrainClient update resolve008Energy 8 -THEShale

443

Zhaosheng Fan | Argonne National Laboratory  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear SecurityTensile Strain Switched FerromagnetismWaste andAnniversary, part 2Zenoss, Version 2.1.3Surface

444

Pressure vessel sliding support unit and system using the sliding support unit  

DOE Patents [OSTI]

Provided is a sliding support and a system using the sliding support unit. The sliding support unit may include a fulcrum capture configured to attach to a support flange, a fulcrum support configured to attach to the fulcrum capture, and a baseplate block configured to support the fulcrum support. The system using the sliding support unit may include a pressure vessel, a pedestal bracket, and a plurality of sliding support units.

Breach, Michael R.; Keck, David J.; Deaver, Gerald A.

2013-01-15T23:59:59.000Z

445

Energy & Society Energy Units and Fundamentals Energy Units and Fundamentals of  

E-Print Network [OSTI]

Energy & Society Energy Units and Fundamentals 1 Toolkit 1: Energy Units and Fundamentals of Quantitative Analysis #12;Energy & Society Energy Units and Fundamentals 2 Table of Contents 1. Key Concepts: Force, Work, Energy & Power 3 2. Orders of Magnitude & Scientific Notation 6 2.1. Orders

Kammen, Daniel M.

446

Impacts of Static Pressure Reset on VAV System Air Leakage, Fan Power and Thermal Energy - Part 2: Case Demonstration for a Typical Climate System  

E-Print Network [OSTI]

. In this part, a simulated air handling unit (AHU) system in Omaha NE is used to demonstrate the energy savings performance in one typical climate year. This AHU system has a static pressure reset system and two constant static pressure systems, one having...

Liu, M.; Zheng, K.; Wu, L.; Wang, Z.; Johnson, C.

2007-01-01T23:59:59.000Z

447

Assessment of Energy Efficiency Improvement in the United States Petroleum Refining Industry  

E-Print Network [OSTI]

27  3.5 Hydrotreating Units (Hydrocracking Unit Hydrotreating Unit Hydrogen Production &to fuel.   3.5 Hydrotreating Units (HTU) Hydrotreating units

Morrow III, William R.

2014-01-01T23:59:59.000Z

448

Estimated United States Transportation Energy Use 2005  

SciTech Connect (OSTI)

A flow chart depicting energy flow in the transportation sector of the United States economy in 2005 has been constructed from publicly available data and estimates of national energy use patterns. Approximately 31,000 trillion British Thermal Units (trBTUs) of energy were used throughout the United States in transportation activities. Vehicles used in these activities include automobiles, motorcycles, trucks, buses, airplanes, rail, and ships. The transportation sector is powered primarily by petroleum-derived fuels (gasoline, diesel and jet fuel). Biomass-derived fuels, electricity and natural gas-derived fuels are also used. The flow patterns represent a comprehensive systems view of energy used within the transportation sector.

Smith, C A; Simon, A J; Belles, R D

2011-11-09T23:59:59.000Z

449

Methods for Allocating Urban Emergency Units  

E-Print Network [OSTI]

An urban emergency service system provides mobile units (vehicles) to respond to requests for service which can occur at any time and any place throughout a city. This paper surveys recent quantitative work aimed at improving ...

Chaiken, Jan M.

450

" Million U.S. Housing Units"  

U.S. Energy Information Administration (EIA) Indexed Site

7 Air-Conditioning Usage Indicators by Climate Zone, 2005" " Million U.S. Housing Units" ,,"Climate Zone1" ,,"Less than 2,000 CDD and --",,,,"2,000 CDD or More and Less than 4,000...

451

" Million U.S. Housing Units" ,,"2005...  

U.S. Energy Information Administration (EIA) Indexed Site

7 Air-Conditioning Usage Indicators by Household Income, 2005" " Million U.S. Housing Units" ,,"2005 Household Income",,,,,"Below Poverty Line","Eligible for Federal Assistance1"...

452

United States Patent [19] Johnson et ai.  

E-Print Network [OSTI]

United States Patent [19] Johnson et ai. [54] ELECTRONIC SOURCING SYSTEM AND METHOD [75] Inventors: James M. Johnson, Bridgeville; Robert P. Kinross, Ben Avon; Francis J. Melly, Pittsburgh; Douglas A

Shamos, Michael I.

453

(12) United States Patent Johnson et ai.  

E-Print Network [OSTI]

(12) United States Patent Johnson et ai. (54) ELECTRONIC SOURCING SYSTEM (75) Inventors: James M. Johnson, Bridgeville, PA (US); Robert P. Kinross, Ben Avon, PA (US); Francis J. Melly, Pittsburgh, PA (US

Shamos, Michael I.

454

United Power- Energy Efficiency Rebate Program  

Broader source: Energy.gov [DOE]

United Power, together with Tri-State Generation and Transmission (TSGT), offers rebates for the installation of a variety of energy efficient equipment including heating and cooling systems, water...

455

OFFICE OF RESOURCE PLANNING OPERATING BUDGET UNIT  

E-Print Network [OSTI]

OFFICE OF RESOURCE PLANNING Manager Sarah Teo OPERATING BUDGET UNIT Deputy Director (Operating, Strategic Initiatives & Consolidated Budgets) Tay Sok Kian Senior Director Ajith Prasad Senior Associate Initiatives & Research Budgets: (Planning & Budget Management) Revenue Policies & Planning: (Grants

Leng, Chenlei

456

Industrial motor repair in the United States  

SciTech Connect (OSTI)

This report characterizes the motor repair industry in the United States; summarizes current motor repair and testing practice; and identifies barriers to energy motor repair practice and recommends strategies for overcoming those barriers.

Schueler, V.; Leistner, P.; Douglass, J.

1994-09-01T23:59:59.000Z

457

Renewable Electricity Generation in the United States  

E-Print Network [OSTI]

This paper provides an overview of the use of renewable energy sources to generate electricity in the United States and a critical analysis of the federal and state policies that have supported the deployment of renewable ...

Schmalensee, Richard

458

Housing Policy in the United States  

E-Print Network [OSTI]

to cite this article Quigley, John M. "housing policy in theHE N EW P ALGRAVE ) By John M. Quigley May 2008 These papersin the United States John M. Quigley From The New Palgrave

Quigley, John M.

2008-01-01T23:59:59.000Z

459

Indoor unit for electric heat pump  

DOE Patents [OSTI]

An indoor unit for an electric heat pump is provided in modular form including a refrigeration module, an air mover module, and a resistance heat package module, the refrigeration module including all of the indoor refrigerant circuit components including the compressor in a space adjacent the heat exchanger, the modules being adapted to be connected to air flow communication in several different ways as shown to accommodate placement of the unit in various orientations. 9 figs.

Draper, R.; Lackey, R.S.; Fagan, T.J. Jr.; Veyo, S.E.; Humphrey, J.R.

1984-05-22T23:59:59.000Z

460

Onsite Wastewater Treatment Systems: Aerobic Treatment Unit  

E-Print Network [OSTI]

wastewater treatment systems use. They remove 85 to 98 percent of the organic matter and solids from the wastewater, producing effluent as clean as that from munici- pal wastewater treatment plants, and cleaner than that from conventional septic tanks.... Onsite wastewater treatment systems Single-compartment trash tank Chlorinator Aerobic treatment unit Spray heads Pump tank Bruce Lesikar Professor and Extension Agricultural Engineer The Texas A&M System Aerobic treatment units, which are certified...

Lesikar, Bruce J.

2008-10-31T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

United States Environmental Protection Agency Office of Water  

E-Print Network [OSTI]

United States Environmental Protection Agency Office of Water Washington, D. C. 20460 United States) OF THE CLEAN WATER ACT I. PURPOSE AND SCOPE. The United States Department of the Army (Army) and the United they determine the geographic jurisdictional scope of waters of the United States for purposes of section 404

US Army Corps of Engineers

462

Economizer Applications in Dual-Duct Air-Handling Units  

E-Print Network [OSTI]

.E.R.O. These homes were constructed by over a dozen different builders. In this paper data from 310 of these homes is presented. These homes have featured better envelopes and windows, interior and/or duct systems with adequate returns, fan integrated positive....1 Maximum HERS 90.3 89.9 Figure 5 HERS Scores for FL H.E.R.O. Homes SF MF Sample Size, n 164 146 Average ACH50 4.5 5.2 Median ACH50 4.4 5.3 Minimum ACH50 2.1 2.2 Maximum ACH50 8.6 8...

Joo, I.; Liu, M.

2002-01-01T23:59:59.000Z

463

United Kingdom HEU Removal | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

HEU Removal United Kingdom HEU Removal Location United Kingdom United States 52 24' 15.1416" N, 1 34' 55.3116" W See map: Google Maps Javascript is required to view this map...

464

United States, Russia Sign Agreement to Further Research and...  

Broader source: Energy.gov (indexed) [DOE]

United States, Russia Sign Agreement to Further Research and Development Collaboration in Nuclear Energy and Security United States, Russia Sign Agreement to Further Research and...

465

Microwave Regenerated DPF for Auxiliary Power Units and Diesel...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Microwave Regenerated DPF for Auxiliary Power Units and Diesel Hybrid Vehicles Microwave Regenerated DPF for Auxiliary Power Units and Diesel Hybrid Vehicles Microwave regeneration...

466

announced united states: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

of the Royal Academy of Engineering, the United Kingdom's National Academy 6 FISHERY STATISTICS UNITED STATES Environmental Sciences and Ecology Websites Summary: FISHERY...

467

Transportation Refrigeration Unit (TRU) Retrofit with HUSS Active...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Transportation Refrigeration Unit (TRU) Retrofit with HUSS Active Diesel Particulate Filters Transportation Refrigeration Unit (TRU) Retrofit with HUSS Active Diesel Particulate...

468

Shared Space vs. In-Unit Upgrades in Multifamily Buildings |...  

Energy Savers [EERE]

Shared Space vs. In-Unit Upgrades in Multifamily Buildings Shared Space vs. In-Unit Upgrades in Multifamily Buildings Better Buildings Neighborhood Program Multifamily Peer...

469

Overview and Progress of United States Advanced Battery Research...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

of United States Advanced Battery Consortium (USABC) Activity United States Advanced Battery Consortium High-Power Electrochemical Storage Devices and Plug-in Hybrid Electric...

470

Geothermal: Sponsored by OSTI -- Joint Egypt/United States report...  

Office of Scientific and Technical Information (OSTI)

Joint EgyptUnited States report on EgyptUnited States cooperative energy assessment. Volume 4 of 5 Vols. Annexes 6--10...

471

United States-Republic of Korea (ROK) International Nuclear Energy...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

United States-Republic of Korea (ROK) International Nuclear Energy Research Initiative (INERI) Annual Steering Committee Meeting United States-Republic of Korea (ROK) International...

472

UNIVERSIT DEGLI STUDI DELLA TUSCIA Didactic and Research Unit  

E-Print Network [OSTI]

UNIVERSITÃ? DEGLI STUDI DELLA TUSCIA Division I Didactic and Research Unit Mobility STUDENTS DIDACTIC AND RESEARCH UNIT Office address: Mobility and International Cooperation Office Via S

Herrmann, Samuel

473

Before the Committee on Energy and Natural Resources United States...  

Office of Environmental Management (EM)

Committee on Energy and Natural Resources United States Senate Before the Committee on Energy and Natural Resources United States Senate Statement Before the Committee on Energy...

474

Gregory H. Friedman: Before the United States Senate Committee...  

Office of Environmental Management (EM)

Gregory H. Friedman: Before the United States Senate Committee on Energy and Natural Resources Gregory H. Friedman: Before the United States Senate Committee on Energy and Natural...

475

Final Report: Particulate Emissions Testing, Unit 1, Potomac...  

Broader source: Energy.gov (indexed) [DOE]

were completed while Unit 1 was operating at 90% of full load (84MW) or greater. Final Report: Particulate Emissions Testing, Unit 1, Potomac River Generating Station, Alexandria,...

476

Assessment of Offshore Wind Energy Resources for the United States...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Offshore Wind Energy Resources for the United States This report summarizes the offshore wind resource potential for the contiguous United States and Hawaii as of May 2009. The...

477

Stepwise redefinition of the SI base units  

E-Print Network [OSTI]

The four SI base units are proposed to be redefined in two stages: first, the kilogram, mole and ampere should be defined, and then the kelvin. To realize the redefinition of a base unit of the SI in terms of fundamental physical constant (FPC), a principle of coincidence of their physical dimensions is put forward. Direct applying this principle will lead to the changing of the sets of base and derived units in the new SI. If we want to preserve the continuity of the division between base and derived units in the new and the current SI, the principle is to be generalized with the time dimension factor be included. The status of the mole as the base unit of measurement is considered in the current and new SI. It is proposed to redefine the kilogram using a fixed value of the Avogadro constant and then to redefine the kelvin, after the measurement accuracy of the Boltzmann constant has been increased and agreed with the values of other constants of molecular physics.

Issaev, L K; Khruschov, V V

2012-01-01T23:59:59.000Z

478

Final Report Independent Verification Survey of the High Flux Beam Reactor, Building 802 Fan House Brookhaven National Laboratory Upton, New York  

SciTech Connect (OSTI)

The Separations Process Research Unit (SPRU) complex located on the Knolls Atomic Power Laboratory (KAPL) site in Niskayuna, New York, was constructed in the late 1940s to research the chemical separation of plutonium and uranium (Figure A-1). SPRU operated as a laboratory scale research facility between February 1950 and October 1953. The research activities ceased following the successful development of the reduction oxidation and plutonium/uranium extraction processes. The oxidation and extraction processes were subsequently developed for large scale use by the Hanford and Savannah River sites (aRc 2008a). Decommissioning of the SPRU facilities began in October 1953 and continued through the 1990s.

Evan Harpeneau

2011-06-24T23:59:59.000Z

479

Section des Units de recherche Rapport de l'AERES sur l'unit  

E-Print Network [OSTI]

Section des Unités de recherche Rapport de l'AERES sur l'unité : Groupe d'études de l représentant de l'AERES : M. Daniel GUEDALIA Représentant(s) des établissements et organismes tutelles de l

Ribes, Aurélien

480

Indoor unit for electric heat pump  

DOE Patents [OSTI]

An indoor unit for an electric heat pump is provided in modular form including a refrigeration module 10, an air mover module 12, and a resistance heat package module 14, the refrigeration module including all of the indoor refrigerant circuit components including the compressor 36 in a space adjacent the heat exchanger 28, the modules being adapted to be connected to air flow communication in several different ways as shown in FIGS. 4-7 to accommodate placement of the unit in various orientations.

Draper, Robert (Churchill, PA); Lackey, Robert S. (Pittsburgh, PA); Fagan, Jr., Thomas J. (Penn HIlls, PA); Veyo, Stephen E. (Murrysville, PA); Humphrey, Joseph R. (Grand Rapids, MI)

1984-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "fan-coil unit fans" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

United Technologies Corp | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revisionEnvReviewNonInvasiveExplorationUT-gTagusparkCalculator JumpUnited States: Energy ResourcesUnited

482

United States Geological Survey | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating SolarElectric Coop,Save Energy Now Jump(EC-LEDS)Agriculture Name: United StatesUnited

483

An energy efficiency guide for use in cleanroom programming  

E-Print Network [OSTI]

MUA Fan Power System Pressure Drop Coil Face Velocity UnitsFan Power System Pressure Drop Air Velocity across filters and coil in air handler Pressurization Cooling Load Units

Tschudi, Bill; Xu, Tengfang; Sartor, Dale

2001-01-01T23:59:59.000Z

484

Fault Detection and Diagnosis in Building HVAC Systems  

E-Print Network [OSTI]

box, fan, and heating/cooling coils in air-handling units.fan efficiency and coil duty. In this chapter, we present a statistical approach for rooftop unit

Najafi, Massieh

2010-01-01T23:59:59.000Z

485

Energy performance of underfloor air distribution systems part V: energy plus development  

E-Print Network [OSTI]

heating coil (fan outlet, coil inlet); the unit air outletVS) fan and reheat coil is an air system terminal unitfan is upstream of the heating coil (this is a blow-through unit).

Buhl, Fred

2007-01-01T23:59:59.000Z

486

FLUIDIZED BED COMBUSTION UNIT FOR OIL SHALE  

E-Print Network [OSTI]

A fluidized bed combustion unit has been designed and installed to study the fluidized bed combustion performance using oil shale as fuel in direct burning process. It is a steel column of 18 cm inside diameter and 130 cm height fitted with a perforated plate air distributor of 611 holes, each of 1

M. Hammad; Y. Zurigat; S. Khzai; Z. Hammad; O. Mubydeem

487

IMUnit: Improved Multithreaded Unit Testing Position Statement  

E-Print Network [OSTI]

IMUnit: Improved Multithreaded Unit Testing Position Statement Vilas Jagannath, Milos Gligoric of schedules, we propose to design a novel language for speci- fying schedules in multithreaded tests-Champaign Urbana, IL 61801, USA {vbangal2, gliga, djin3, grosu, marinov}@illinois.edu ABSTRACT This position paper

Marinov, Darko

488

Effective Energy Conservation in the Operating Unit  

E-Print Network [OSTI]

can odcur. At that point, positive steps need to be takerl to rejuvenate the process. Suci, a step might weIll in clude a energy brainstorming session(s} where Ithe interaction between people can jar out some i~eas. that the unit coordinator has a...

Korich, R. D.

1982-01-01T23:59:59.000Z

489

In This Issue United States and European  

E-Print Network [OSTI]

the Corn Rootworm Results of an Indiana Farmer Survey . . . . . . . . . . . . . . . . . 8 37th Top Farmer Crop Workshop . . . . . . . . . . . . . . . . . . . . 12 ew issues in United States (U.S.) agriculture, biotechnology has the potential to lower production costs by reducing input usage. Biotechnology also has

490

Legislating Biofuels in the United States  

E-Print Network [OSTI]

Legislating Biofuels in the United States Wendy Clark National Renewable Energy Laboratory Golden, Colorado, USA 2008 SAE Biofuels Specifications and Performance Symposium July 7-9, 2008, Paris NREL PR-540 Legislate Biofuels? · Plentiful U.S. biomass resources: energy crops, agricultural and forestry residues

491

Tracking Mobile Units for Dependable Message Delivery  

E-Print Network [OSTI]

Tracking Mobile Units for Dependable Message Delivery Amy L. Murphy, Member, IEEE Computer Society at their disposal at any time, mobile computing is developing as an important research area. One of the fundamental problems in mobility is maintaining connectivity through message passing as the user moves through

Zhou, Yuanyuan

492

Foreign Fishery Developments United States-Spain  

E-Print Network [OSTI]

Foreign Fishery Developments United States-Spain Fisheries Trade, 1980-85 Introduction The U though Spain was forced to become a net importer of fishery products in 1977. due to the extension of 200-mile Exclusive Economic Zones (EEZ) by coastal coun tries. U.S. exports of edible seafoods to Spain

493

Managing nuclear weapons in the United States  

SciTech Connect (OSTI)

This report discusses the management and security of nuclear weapons in the post-cold war United States. The definition of what constitutes security is clearly changing in the US. It is now a much more integrated view that includes defense and the economy. The author tries to bring some semblance of order to these themes in this brief adaptation of a presentation.

Miller, G.

1993-03-16T23:59:59.000Z

494

Operating Instructions CASSEHE PUMP DRIVE UNIT  

E-Print Network [OSTI]

4 · Operating Instructions CASSEHE® PUMP DRIVE UNIT Catalog No. 72-510-000 72-510-220 PUMPING The squeezing action of rollers on tubing causes the peristaltic pumping action. The flow is proportionate to the speied of the rollers and the inside diameter of the tubing, both of which can be varied. Pumping

Kleinfeld, David

495

Conservation of Lynx in the United States  

E-Print Network [OSTI]

455 Chapter 17 Conservation of Lynx in the United States: A Systematic Approach to Closing Critical. To avoid haphazard research and to maximize the benefits to lynx conservation with limited research funds on lynx in the U.S. to be a significant impediment to science-based conservation and management. New

496

Cell Phone Allowance Responsible Administrative Units  

E-Print Network [OSTI]

Cell Phone Allowance Policy Responsible Administrative Units: Office of Finance & Administration 1 of 3 1.0 BACKGROUND It is essential for certain employees in some circumstances to use cell phones of Colorado policy that dictates use of a state-provided cell phone or smartphone. Additionally, the Internal

497

INTRODUCTION TO THE LHC UNIT OVERVIEW  

E-Print Network [OSTI]

by the Standard Model UNIT OBJECTIVES · List the building blocks of matter and the interactions between them · Basic research is a journey--not an event. · The Standard Model is the current framework for our. · Describe fundamental questions not explained by the Standard Model that the LHC and its experiments

Quigg, Chris

498

United States Patent [19] Church et al.  

E-Print Network [OSTI]

United States Patent [19] Church et al. [54] CHARACTERIZATION OF INDIVIDUAL POLYMER MOLECULES BASED al.. "ANeutral Amino Acid Change in Segment TIS4 Dramatically Alters the Gating Properties of the Volt- age-Dependent Sodium Channel". 1990, Proc. Natl. Acad. Sci. USA, 87:323-27. Bensirnon. A.. et al

Church, George M.

499

(12) United States Patent Likourezos et al.  

E-Print Network [OSTI]

(12) United States Patent Likourezos et al. (54) SYSTEM AND METHOD FOR EFFECTING A REAL: Nov. 14, 2001 (65) Prior Publication Data US 2002/0095377 Al Jul. 18, 2002 Related U.S. Application Cited U.S. PATENT DOCUMENTS 4,799,156 A 4,876,648 A 111989 Shavit et al. 1011989 Lloyd 102 102 111111

Shamos, Michael I.

500

(12) United States Patent Reardan et al.  

E-Print Network [OSTI]

(12) United States Patent Reardan et al. (54) SENSITIVE DRUG DISTRIBUTION SYSTEM AND METHOD (75 2004/0117205 Al Jun. 17,2004 (51) Int. Cl. G06Q 10/00 (2006.01) (52) U.S. Cl/231 4,976,351 A 1211990 Mangini et al. 5,737,539 A * 411998 Edelson et al. ................. 705/3 5

Shamos, Michael I.