National Library of Energy BETA

Sample records for factors shown represent

  1. Facility Representatives

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-03-01

    This standard, DOE-STD-1063, Facility Representatives, defines the duties, responsibilities and qualifications for Department of Energy (DOE) Facility Representatives, based on facility hazard classification; risks to workers, the public, and the environment; and the operational activity level. This standard provides the guidance necessary to ensure that DOE’s hazardous nuclear and non-nuclear facilities have sufficient staffing of technically qualified facility representatives (FRs) to provide day-to-day oversight of contractor operations.

  2. Facility Representatives

    Office of Environmental Management (EM)

    DOE-STD-1063-2006 April 2006 Superseding DOE-STD-1063-2000 March 2000 DOE STANDARD FACILITY REPRESENTATIVES U.S. Department of Energy AREA MGMT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. NOT MEASUREMENT SENSITIVE DOE-STD-1063-2006 ii Available on the Department of Energy Technical Standards Program web site at http://www.eh.doe.gov/techstds/ DOE-STD-1063-2006 iii FOREWORD 1. This Department of Energy standard is approved for use by

  3. Facility Representatives

    Office of Environmental Management (EM)

    063-2011 February 2011 Superseding DOE-STD-1063-2006 April 2006 DOE STANDARD FACILITY REPRESENTATIVES U.S. Department of Energy AREA MGMT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. NOT MEASUREMENT SENSITIVE DOE-STD-1063-2011 ii Available on the Department of Energy Technical Standards Program Web site at http://www.hss.doe.gov/nuclearsafety/ns/techstds/ DOE-STD-1063-2011 iii FOREWORD 1. This Department of Energy (DOE) standard is

  4. Final Rulemaking, 10 CFR Part 1021, with Amendments Shown In Tracked

    Office of Environmental Management (EM)

    Changes | Department of Energy Rulemaking, 10 CFR Part 1021, with Amendments Shown In Tracked Changes Final Rulemaking, 10 CFR Part 1021, with Amendments Shown In Tracked Changes This document presents the final rule as issued September 27, 2011, amendments shown with changes tracked (additions in blue, deletions in red). Categorical exclusions are listed in Appendices A and B to Subpart D. PDF icon 10 CFR Part 1021 changes tracked.pdf More Documents & Publications 10 CFR 1021 --

  5. DOE Takes Action to Stop the Sales of Air-Con Air Conditioner Models Shown

    Energy Savers [EERE]

    to Violate Federal Energy Efficiency Appliance Standards | Department of Energy Action to Stop the Sales of Air-Con Air Conditioner Models Shown to Violate Federal Energy Efficiency Appliance Standards DOE Takes Action to Stop the Sales of Air-Con Air Conditioner Models Shown to Violate Federal Energy Efficiency Appliance Standards September 23, 2010 - 12:00am Addthis Washington, DC - The Department of Energy announced today that it has taken action against Air-Con, International, requiring

  6. TEC Working Group Member Organizations Representatives | Department...

    Office of Environmental Management (EM)

    Member Organizations Representatives TEC Working Group Member Organizations Representatives PDF icon TEC MEMBER ORGANIZATION REPRESENTATIVES TOPIC GROUP PARTICIPATION February 2006...

  7. Authorizing Official Designated Representative (AODR) | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Designated Representative (AODR) Authorizing Official Designated Representative (AODR) student-849822960720.jpg The Authorizing Official Designated Representative (AODR) provides...

  8. Property Representatives Lists - HQ | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Property Representatives Lists - HQ Property Representatives Lists - HQ These are the current lists of Headquarters Property Representatives. If you have any questions please contact: Ellen Hall, Office of Logistics Operations, (301) 903-2613. PDF icon Authorized Property Pass Signers List and Accountable Property Representatives List, Effective December 2, 2015 More Documents & Publications Directory Listings AU Functional Area Points of Contact by Office Directors Customer Services

  9. Facility Representative Program Outstanding at ID

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    June 19, 2007 Facility Representative Program Outstanding at ID Idaho's three DOE Complex-wide Facility Representative of the Year (FROTY) recipients at this year's conference pose for a photo shoot with Elvis. L to R: Dary Newbry 2005 FROTY, Bob Seal 2006 FROTY, Bob Knighten 2004 FROTY Facility representatives (FRs) are the eyes and ears of the federal government at the Idaho National Laboratory. They oversee the people, processes, facilities and systems that ensure safety at INL facilities.

  10. DOE RL Contracting Officer Representatives - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Officer Representatives DOE-RL Contracts/Procurements RL Contracts & Procurements Home Prime Contracts Current Solicitations Other Sources DOE RL Contracting Officers DOE RL Contracting Officer Representatives DOE RL Contracting Officer Representatives Email Email Page | Print Print Page |Text Increase Font Size Decrease Font Size CO/COR Contract Number Company Acronym Limitations CAROSINO, ROBERT M DE-AC06-08RL14788 CPRC DE-AC06-08RL14788, CH2M HILL PLATEAU REMEDIATION COMPANY (CHPRC),

  11. Facility Representative Qualification Equivalencies Based on Previous

    Office of Environmental Management (EM)

    Experience | Department of Energy Facility Representative Qualification Equivalencies Based on Previous Experience Facility Representative Qualification Equivalencies Based on Previous Experience The referenced document has been used by the Department of Energy, Idaho Operations Office (DOE-ID) to grant equivalencies to candidates undergoing qualification as a Facility Representative (FR) using the FR Functional Area Qualification Standards (FAQS). Since the generation of the referenced

  12. Facility Representative of the Year Award

    Broader source: Energy.gov [DOE]

    The Facility Representative Award Program is a special award designed to recognize superior or exemplary service by a Facility Representative over a period of one year. This special award program has been established in accordance with the requirements of Department of Energy (DOE) Order 331.1C, Employee Performance Management and Recognition Program.

  13. Facility Representative Program, Criteria & Review Approach Documents

    Broader source: Energy.gov [DOE]

    This page provides Criteria Review and Approach Documents (CRADS) to assist Facility Representatives. Please submit your CRADS for posting by sending them to the HQ FR Program Manager. Please include the subject, date, and a contact person.

  14. Advisory Board Seats New Student Representatives

    Broader source: Energy.gov [DOE]

    The Oak Ridge Site Specific Advisory Board (ORSSAB) welcomed two new student representatives at its May meeting. Gracie Hall and Julia Riley will serve on the board through April 2014.

  15. Incentives for the Department's Facility Representative Program,

    Office of Environmental Management (EM)

    12/17/1998 | Department of Energy Incentives for the Department's Facility Representative Program, 12/17/1998 Incentives for the Department's Facility Representative Program, 12/17/1998 The Department's Revised Implementation Plan for Defense Nuclear Facilities Safety Board Recommendation 93-3 has once again underscored the Department's commitment to maintaining the technical capability necessary to safely manage and operate our defense nuclear facilities. Attracting and retaining highly

  16. Data structures and apparatuses for representing knowledge

    DOE Patents [OSTI]

    Hohimer, Ryan E; Thomson, Judi R; Harvey, William J; Paulson, Patrick R; Whiting, Mark A; Tratz, Stephen C; Chappell, Alan R; Butner, Robert S

    2014-02-18

    Data structures and apparatuses to represent knowledge are disclosed. The processes can comprise labeling elements in a knowledge signature according to concepts in an ontology and populating the elements with confidence values. The data structures can comprise knowledge signatures stored on computer-readable media. The knowledge signatures comprise a matrix structure having elements labeled according to concepts in an ontology, wherein the value of the element represents a confidence that the concept is present in an information space. The apparatus can comprise a knowledge representation unit having at least one ontology stored on a computer-readable medium, at least one data-receiving device, and a processor configured to generate knowledge signatures by comparing datasets obtained by the data-receiving devices to the ontologies.

  17. Facility Representative Functional Area Qualification Standard

    Office of Environmental Management (EM)

    DOE-STD-1151-2010 October 2010 DOE STANDARD FACILITY REPRESENTATIVE FUNCTIONAL AREA QUALIFICATION STANDARD DOE Defense Nuclear Facilities Technical Personnel U.S. Department of Energy AREA TRNG Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. DOE-STD-1151-2010 ii This document is available on the Department of Energy Office of Health, Safety and Security Approved DOE Technical Standards Web Site at

  18. house of representatives | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    house of representatives | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Library Bios Congressional Testimony Fact Sheets Newsletters Press Releases Photo Gallery Jobs Apply for Our Jobs Our Jobs Working

  19. Yucca Mountain Climate Technical Support Representative

    SciTech Connect (OSTI)

    Sharpe, Saxon E

    2007-10-23

    The primary objective of Project Activity ORD-FY04-012, “Yucca Mountain Climate Technical Support Representative,” was to provide the Office of Civilian Radioactive Waste Management (OCRWM) with expertise on past, present, and future climate scenarios and to support the technical elements of the Yucca Mountain Project (YMP) climate program. The Climate Technical Support Representative was to explain, defend, and interpret the YMP climate program to the various audiences during Site Recommendation and License Application. This technical support representative was to support DOE management in the preparation and review of documents, and to participate in comment response for the Final Environmental Impact Statement, the Site Recommendation Hearings, the NRC Sufficiency Comments, and other forums as designated by DOE management. Because the activity was terminated 12 months early and experience a 27% reduction in budget, it was not possible to complete all components of the tasks as originally envisioned. Activities not completed include the qualification of climate datasets and the production of a qualified technical report. The following final report is an unqualified summary of the activities that were completed given the reduced time and funding.

  20. PWR representative behavior during a LOCA

    SciTech Connect (OSTI)

    Allison, C.M.

    1981-01-01

    To date, there has been substantial analytical and experimental effort to define the margins between design basis loss-of-coolant accident (LOCA) behavior and regulatory limits on maximum fuel rod cladding temperature and deformation. As a result, there is extensive documentation on the modeling of fuel rod behavior in test reactors and design basis LOCA's. However, modeling of that behavior using representative, non-conservative, operating histories is not nearly as well documented in the public literature. Therefore, the objective of this paper is (a) to present calculations of LOCA induced behavior for Pressurized Water Reactor (PWR) core representative fuel rods, and (b) to discuss the variability in those calculations given the variability in fuel rod condition at the initiation of the LOCA. This analysis was limited to the study of changes in fuel rod behavior due to different power operating histories. The other two important parameters which affect that behavior, initial fuel rod design and LOCA coolant conditions were held invarient for all of the representative rods analyzed.

  1. Residential Energy-Efficiency Equipment Shown to be a Good Investment for U.S. Navy (Fact Sheet), NREL (National Renewable Energy Laboratory)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL/FS-6A00-61218 * April 2014 National Renewable Energy Laboratory 15013 Denver West Parkway, Golden, CO 80401 303-275-3000 * www.nrel.gov Printed with a renewable-source ink on paper containing at least 50% wastepaper, including 10% post consumer waste. Residential Energy-Efficiency Equipment Shown to be a Good Investment for U.S. Navy A two-year project between the National Renewable Energy Laboratory (NREL) and the U.S. Navy's Naval Facilities Engineering Command (NAVFAC) to demonstrate

  2. Microsoft Word - SEC J_Appendix S- Contracting Officer's Representative_s_

    National Nuclear Security Administration (NNSA)

    J, Page 1 SECTION J APPENDIX S CONTRACTING OFFICER REPRESENTATIVES The following individuals are designated as CORs for the Kansas City Plant Contract. Each is limited to the specific areas listed by his/her name. Contracting Officer Representatives Name Location Limited Area of Responsibility Shoulta, Jeffrey L. KCSO Production & Quality Management Hoopes, Patrick T. KCSO Environment, Safety and Health; Facilities Management; Security and Information Systems Schmidt, Robert E. KCSO Project

  3. Single-point representative sampling with shrouded probes

    SciTech Connect (OSTI)

    McFarland, A.R.; Rodgers, J.C.

    1993-08-01

    The Environmental Protection Agency (EPA) prescribed methodologies for sampling radionuclides in air effluents from stacks and ducts at US Department of Energy (DOE) facilities. Requirements include use of EPA Method 1 for the location of sampling sites and use of American National Standards Institute (ANSI) N13.1 for guidance in design of sampling probes and the number of probes at a given site. Application of ANSI N13.1 results in sampling being performed with multiprobe rakes that have as many as 20 probes. There can be substantial losses of aerosol particles in such sampling that will degrade the quality of emission estimates from a nuclear facility. Three alternate methods, technically justified herein, are proposed for effluent sampling. First, a shrouded aerosol sampling probe should replace the sharp-edged elbowed-nozzle recommended by ANSI. This would reduce the losses of aerosol particles in probes and result in the acquisition of more representative aerosol samples. Second, the rakes of multiple probes that are intended to acquire representative samples through spatial coverage should be replaced by a single probe located where contaminant mass and fluid momentum are both well mixed. A representative sample can be obtained from a well-mixed flow. Some effluent flows will need to be engineered to achieve acceptable mixing. Third, sample extraction should be performed at a constant flow rate through a suitable designed shrouded probe rather than at a variable flow rate through isokinetic probes. A shrouded probe is shown to have constant sampling characteristics over a broad range of stack velocities when operated at a fixed flow rate.

  4. 1998 Annual Facility Representative Workshop Attendees | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy 998 Annual Facility Representative Workshop Attendees 1998 Annual Facility Representative Workshop Attendees 1998 Annual Facility Representative Workshop Attendees PDF icon 1998 Annual Facility Representative Workshop Attendees More Documents & Publications 1999 Annual Facility Representative Workshop Attendees FTCP Members DOE ISM Champions - 2012

  5. Representativeness-based Sampling Network Design for the State...

    Office of Scientific and Technical Information (OSTI)

    Representativeness-based Sampling Network Design for the State of Alaska Citation Details In-Document Search Title: Representativeness-based Sampling Network Design for the State...

  6. Representativeness based Sampling Network Design for the State...

    Office of Scientific and Technical Information (OSTI)

    Representativeness based Sampling Network Design for the State of Alaska Title: Representativeness-based Sampling Network Design for the State of Alaska Authors: Forrest M. Hoffman...

  7. Representativeness-Based Sampling Network Design for the State...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Representativeness-Based Sampling Network Design for the State of Alaska Citation Details In-Document Search Title: Representativeness-Based Sampling Network...

  8. 3Q CY2005 (PDF), Facility Representative Program Performance...

    Office of Environmental Management (EM)

    3Q CY2005 (PDF), Facility Representative Program Performance Indicators Quarterly Report 3Q CY2005 (PDF), Facility Representative Program Performance Indicators Quarterly Report...

  9. 1Q CY2000 (PDF), Facility Representative Program Performance...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report 1Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report...

  10. Facility Representative Program ID Selects FR of the Year

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Facility Representative Program ID Selects FR of the Year John Martin DOE-ID Facility Representative John Martin DOE-ID Facility Representative of the Year. John Martin was selected as DOE-ID's Facility Representative of the Year and the office's nominee for the 2007 DOE Facility Representative of the Year Award. John was selected from an exceptional field of candidates to represent DOE-ID at the Facility Representative Annual Workshop in Las Vegas this May. Each year the Department of Energy

  11. FACILITY REPRESENTATIVE PROGRAM STATUS, 6/21/1999

    Broader source: Energy.gov [DOE]

    Since September, 1993, the Office of Field Management has served as the Department’s corporate advocate for the Facility Representative Program. The Facility Representative (FR) is a critical...

  12. 1999 FACILITY REPRESENTATIVE CONFERENCE June 21 – 25, 1999

    Broader source: Energy.gov [DOE]

    The Department of Energy will host the Facility Representative Annual Meeting on June 21-25, 1999 at the Alexis Park Hotel in Las Vegas, Nevada. The meeting will give Facility Representatives and...

  13. 1Q CY2000 (PDF), Facility Representative Program Performance Indicators

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Quarterly Report | Department of Energy Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report 1Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report "The Facility Representative Program Performance Indicators (PIs) Quarterly Report is attached, covering the period from January 2000 to March 2000. Data for these indicators are gathered by the Field elements quarterly per the Facility Representatives Standard, DOE-STD-1

  14. 4Q CY2000 (PDF), Facility Representative Program Performance Indicators

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Quarterly Report | Department of Energy 4Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report 4Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report "The Facility Representative Program Performance Indicators Quarterly Report is attached, covering the period from October to December 2000. Data for these indicators are gathered by the Field elements quarterly per the Facility Representatives Standard, 063, and reported

  15. FAQS Reference Guide - Facility Representative | Department of Energy

    Office of Environmental Management (EM)

    Facility Representative FAQS Reference Guide - Facility Representative This reference guide addresses the competency statements in the October 2010 edition of DOE-STD-1151-2010, Facility Representative Functional Area Qualification Standard. PDF icon Facility Representative Qualification Standard Reference Guide, October 2010 More Documents & Publications DOE-HDBK-1018/2-93 DOE-HDBK-1018/1-93 DOE-STD-1161-2008

  16. Office of Departmental Representative to DNFSB | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Departmental Representative to DNFSB Office of Departmental Representative to DNFSB Mission The Department Representative to the Defense Nuclear Facilities Safety Board (DNFSB) provides effective cross-organizational leadership in resolving DNFSB-related technical and management issues necessary to ensure public health and safety. Functions Represents the Secretary and the Associate Deputy Secretary in regular and continuing interactions with the DNFSB(and/or also referred to as Board). Advises

  17. Defining And Characterizing Sample Representativeness For DWPF Melter Feed Samples

    SciTech Connect (OSTI)

    Shine, E. P.; Poirier, M. R.

    2013-10-29

    Representative sampling is important throughout the Defense Waste Processing Facility (DWPF) process, and the demonstrated success of the DWPF process to achieve glass product quality over the past two decades is a direct result of the quality of information obtained from the process. The objective of this report was to present sampling methods that the Savannah River Site (SRS) used to qualify waste being dispositioned at the DWPF. The goal was to emphasize the methodology, not a list of outcomes from those studies. This methodology includes proven methods for taking representative samples, the use of controlled analytical methods, and data interpretation and reporting that considers the uncertainty of all error sources. Numerous sampling studies were conducted during the development of the DWPF process and still continue to be performed in order to evaluate options for process improvement. Study designs were based on use of statistical tools applicable to the determination of uncertainties associated with the data needs. Successful designs are apt to be repeated, so this report chose only to include prototypic case studies that typify the characteristics of frequently used designs. Case studies have been presented for studying in-tank homogeneity, evaluating the suitability of sampler systems, determining factors that affect mixing and sampling, comparing the final waste glass product chemical composition and durability to that of the glass pour stream sample and other samples from process vessels, and assessing the uniformity of the chemical composition in the waste glass product. Many of these studies efficiently addressed more than one of these areas of concern associated with demonstrating sample representativeness and provide examples of statistical tools in use for DWPF. The time when many of these designs were implemented was in an age when the sampling ideas of Pierre Gy were not as widespread as they are today. Nonetheless, the engineers and statisticians used carefully thought out designs that systematically and economically provided plans for data collection from the DWPF process. Key shared features of the sampling designs used at DWPF and the Gy sampling methodology were the specification of a standard for sample representativeness, an investigation that produced data from the process to study the sampling function, and a decision framework used to assess whether the specification was met based on the data. Without going into detail with regard to the seven errors identified by Pierre Gy, as excellent summaries are readily available such as Pitard [1989] and Smith [2001], SRS engineers understood, for example, that samplers can be biased (Gy�s extraction error), and developed plans to mitigate those biases. Experiments that compared installed samplers with more representative samples obtained directly from the tank may not have resulted in systematically partitioning sampling errors into the now well-known error categories of Gy, but did provide overall information on the suitability of sampling systems. Most of the designs in this report are related to the DWPF vessels, not the large SRS Tank Farm tanks. Samples from the DWPF Slurry Mix Evaporator (SME), which contains the feed to the DWPF melter, are characterized using standardized analytical methods with known uncertainty. The analytical error is combined with the established error from sampling and processing in DWPF to determine the melter feed composition. This composition is used with the known uncertainty of the models in the Product Composition Control System (PCCS) to ensure that the wasteform that is produced is comfortably within the acceptable processing and product performance region. Having the advantage of many years of processing that meets the waste glass product acceptance criteria, the DWPF process has provided a considerable amount of data about itself in addition to the data from many special studies. Demonstrating representative sampling directly from the large Tank Farm tanks is a difficult, if not unsolvable enterprise due to limited accessibility. However, the consistency and the adequacy of sampling and mixing at SRS could at least be studied under the controlled process conditions based on samples discussed by Ray and others [2012a] in Waste Form Qualification Report (WQR) Volume 2 and the transfers from Tanks 40H and 51H to the Sludge Receipt and Adjustment Tank (SRAT) within DWPF. It is important to realize that the need for sample representativeness becomes more stringent as the material gets closer to the melter, and the tanks within DWPF have been studied extensively to meet those needs.

  18. CNS represented at inaugural Energetics Consortium | Y-12 National Security

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Complex CNS represented at ... CNS represented at inaugural Energetics Consortium Posted: February 16, 2016 - 6:53pm CNS was well represented at the first National Energetic Materials Consortium. About 70 university researchers and government and industry experts from across the country, including Consolidated Nuclear Security employees, joined forces at the first ever National Energetic Materials Consortium hosted by Texas Tech University. Pantex's Christopher Young said, "There are a

  19. The Representative Concentration Pathways: An Overview (Journal Article) |

    Office of Scientific and Technical Information (OSTI)

    SciTech Connect The Representative Concentration Pathways: An Overview Citation Details In-Document Search Title: The Representative Concentration Pathways: An Overview This paper summarizes the development process and main characteristics of the Representative Concentration Pathways (RCPs), a set of four new scenarios developed for the climate modeling community as a basis for long-term and near-term modeling experiments. The four RCPs together span the range of year 2100 radiative forcing

  20. CRAD, NNSA - Facility Representatives (FR) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Facility Representatives (FR) CRAD, NNSA - Facility Representatives (FR) CRAD for Facility Representatives (FR). Criteria Review and Approach Documents (CRADs) that can be used to conduct a well-organized and thorough assessment of elements of safety and health programs. CRADs consist of a Performance Objective that identifies the expectation(s) or requirement(s) to be verified, which reflect the complete scope of the assessment; Criteria that provide specifics by which the performance

  1. Departmental Representative to the Defense Nuclear Facilities Safety Board

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (DNFSB) | Department of Energy Departmental Representative to the Defense Nuclear Facilities Safety Board (DNFSB) Departmental Representative to the Defense Nuclear Facilities Safety Board (DNFSB) The Office of the Departmental Representative ensures effective cross-organizational leadership and coordination to resolve DNFSB-identified technical and management issues as we work to ensure the health, safety, and security of the workers, public, and environment. This web site is an important

  2. UESC Training for Utility Representatives | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    UESC Training for Utility Representatives UESC Training for Utility Representatives January 27, 2016 11:00AM to 1:00PM EST Webinar covers utility energy service contracts (UESC), which allow utilities to provide their Federal agencies with comprehensive energy and water efficiency improvements and demand-reduction services. To enter into a UESC, Federal staff, as well as utility representatives, must understand the legal parameters, contracting requirements, financing options, and other aspects

  3. DOE/Advisory Board Recognize Service of Student Representatives |

    Office of Environmental Management (EM)

    Department of Energy DOE/Advisory Board Recognize Service of Student Representatives DOE/Advisory Board Recognize Service of Student Representatives April 16, 2014 - 12:58pm Addthis The Oak Ridge Site Specific Advisory Board (ORSSAB) and the U.S. Department of Energy's (DOE) Oak Ridge Office recognized outgoing student representatives Gracie Hall and Julia Riley at the April board meeting. ORSSAB is a federally chartered citizens' panel that provides recommendations to the DOE Oak Ridge

  4. Appointment of Contracting Officers and Contracting Officer Representatives

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2004-04-21

    The Order established procedures governing the selection, appointment and termination of Department of Energy contracting officers and contracting officer representatives. Supersedes DOE O 541.1A.

  5. Dr. Kelli Joseph, NYISO Representing the ISO-RTO Council

    Broader source: Energy.gov (indexed) [DOE]

    Kelli Joseph, NYISO Representing the ISO-RTO Council July 28, 2014 DOE Quadrennial Energy Review Gas Electric Interdependencies: Coordination Efforts, Regional Issues, and...

  6. On April 25, 2013, several representatives of energy efficiency...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Representing compressor manufacturers were Jordan Doria, Mark Krisa, Rob Haseley (Ingersoll Rand), Wayne Perry, Werner Rauer, Stephen Horne and Waheed Chaudury (Kaeser), Gary ...

  7. Utility Energy Service Contracts Training for Utility Representatives

    Broader source: Energy.gov [DOE]

    This webinar targets Federal staff, as well as utility representatives, and provides an understanding of the legal parameters, contracting requirements, financing options, and other aspects of utility energy service contracts (UESC).

  8. Department of Defense Representatives Visit Hanford to Benchmark Safety

    Broader source: Energy.gov [DOE]

    RICHLAND, Wash., December 16, 2005, Representatives of the Department of Defense's (DoD's) Voluntary Protection Program Center of Excellence (VPP CX) working to reduce injuries at selected (DoD)...

  9. Changes to the Facility Representative Program, 10/26/1999

    Broader source: Energy.gov [DOE]

    Effective October 1, 1999, the Deputy Secretary tasked this office to manage the Facility Representative Program. We look forward to working with you in continuing and improving this very important...

  10. Appointment of Contracting Officers and Contracting Officer Representatives

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1996-04-30

    To establish procedures governing the selection, appointment, and termination of contracting officers and for the appointment of contracting officer representatives. Cancels DOE Order 4200.4A. Canceled by DOE O 541.1A.

  11. Radionuclide Interaction and Transport in Representative Geologic Media |

    Energy Savers [EERE]

    Department of Energy Radionuclide Interaction and Transport in Representative Geologic Media Radionuclide Interaction and Transport in Representative Geologic Media The report presents information related to the development of a fundamental understanding of disposal-system performance in a range of environments for potential wastes that could arise from future nuclear fuel cycle alternatives. It addresses selected aspects of the development of computational modeling capability for the

  12. FAQS Job Task Analyses - Facility Representative | Department of Energy

    Office of Environmental Management (EM)

    Facility Representative FAQS Job Task Analyses - Facility Representative FAQS Job Task Analyses are performed on the Function Area Qualification Standards. The FAQS Job Task Analyses consists of: Developing a comprehensive list of tasks that define the job such as the duties and responsibilities which include determining their levels of importance and frequency. Identifying and evaluating competencies. Last step is evaluating linkage between job tasks and competencies. PDF icon FAQS JTA -

  13. Landscape Characterization and Representativeness Analysis for Understanding Sampling Network Coverage

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Maddalena, Damian; Hoffman, Forrest; Kumar, Jitendra; Hargrove, William

    Sampling networks rarely conform to spatial and temporal ideals, often comprised of network sampling points which are unevenly distributed and located in less than ideal locations due to access constraints, budget limitations, or political conflict. Quantifying the global, regional, and temporal representativeness of these networks by quantifying the coverage of network infrastructure highlights the capabilities and limitations of the data collected, facilitates upscaling and downscaling for modeling purposes, and improves the planning efforts for future infrastructure investment under current conditions and future modeled scenarios. The work presented here utilizes multivariate spatiotemporal clustering analysis and representativeness analysis for quantitative landscape characterization and assessment of the Fluxnet, RAINFOR, and ForestGEO networks. Results include ecoregions that highlight patterns of bioclimatic, topographic, and edaphic variables and quantitative representativeness maps of individual and combined networks.

  14. Landscape Characterization and Representativeness Analysis for Understanding Sampling Network Coverage

    SciTech Connect (OSTI)

    Maddalena, Damian; Hoffman, Forrest; Kumar, Jitendra; Hargrove, William

    2014-08-01

    Sampling networks rarely conform to spatial and temporal ideals, often comprised of network sampling points which are unevenly distributed and located in less than ideal locations due to access constraints, budget limitations, or political conflict. Quantifying the global, regional, and temporal representativeness of these networks by quantifying the coverage of network infrastructure highlights the capabilities and limitations of the data collected, facilitates upscaling and downscaling for modeling purposes, and improves the planning efforts for future infrastructure investment under current conditions and future modeled scenarios. The work presented here utilizes multivariate spatiotemporal clustering analysis and representativeness analysis for quantitative landscape characterization and assessment of the Fluxnet, RAINFOR, and ForestGEO networks. Results include ecoregions that highlight patterns of bioclimatic, topographic, and edaphic variables and quantitative representativeness maps of individual and combined networks.

  15. WIPP Representative Selected For National Environmental Justice Advisory Board

    Broader source: Energy.gov [DOE]

    CARLSBAD, N.M. – Organizers say no similar opportunity or conference exists in America. In April, representatives from federal and state agencies, local governments, tribes, communities, business, academia and other groups will gather in Washington, D.C. for the 2012 National Environmental Justice Conference and Training Program.

  16. Appointment of Contracting Officers and Contracting Officer's Representatives

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2000-10-27

    To establish procedures governing the selection, appointment, and termination of contracting officers and for the appointment of contracting officer's representatives. To ensure that only trained and qualified procurement and financial assistance professionals, within the scope of this Order, serve as contracting officers. Cancels DOE O 541.1. Canceled by DOE O 541.1B.

  17. DOE Representative to World Institute of Nuclear Safety (WINS) | National

    National Nuclear Security Administration (NNSA)

    Nuclear Security Administration Representative to World Institute of Nuclear Safety (WINS) | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Library Bios Congressional Testimony Fact Sheets Newsletters

  18. Processes, data structures, and apparatuses for representing knowledge

    DOE Patents [OSTI]

    Hohimer, Ryan E. (West Richland, WA); Thomson, Judi R. (Guelph, CA); Harvey, William J. (Richland, WA); Paulson, Patrick R. (Pasco, WA); Whiting, Mark A. (Richland, WA); Tratz, Stephen C. (Richland, WA); Chappell, Alan R. (Seattle, WA); Butner, R. Scott (Richland, WA)

    2011-09-20

    Processes, data structures, and apparatuses to represent knowledge are disclosed. The processes can comprise labeling elements in a knowledge signature according to concepts in an ontology and populating the elements with confidence values. The data structures can comprise knowledge signatures stored on computer-readable media. The knowledge signatures comprise a matrix structure having elements labeled according to concepts in an ontology, wherein the value of the element represents a confidence that the concept is present in an information space. The apparatus can comprise a knowledge representation unit having at least one ontology stored on a computer-readable medium, at least one data-receiving device, and a processor configured to generate knowledge signatures by comparing datasets obtained by the data-receiving devices to the ontologies.

  19. Howard University Researchers Represented in the E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Howard University Researchers Represented in the E-print Network Researcher/Research Institution Web page Eckberg, William R. - Department of Biology, Howard University http://www.biology.howard.edu/ Faculty/FacultyBios/Eckberg.htm Hindman, Neil - Department of Mathematics, Howard University http://mysite.verizon.net/nhindman/ Sitaraman, Sankar - Department of Mathematics, Howard University http://nature-lover.net/math/R/rp.html

  20. DOE-STD-1063-2000 - Facility Representatives

    Office of Environmental Management (EM)

    NOT MEASUREMENT SENSITIVE DOE-STD-1063-2000 March 2000 Superseding DOE-STD-1063-97 October 1997 DOE STANDARD FACILITY REPRESENTATIVES U.S. Department of Energy AREA MGMT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. TS This document has been reproduced from the best available copy. Available to DOE and DOE contractors from ES&H Technical Information Services, U.S. Department of Energy, (800) 473-4375, fax: (301) 903-9823. Available

  1. The Korarchaeota: Archaeal orphans representing an ancestral lineage of life

    SciTech Connect (OSTI)

    Elkins, James G.; Kunin, Victor; Anderson, Iain; Barry, Kerrie; Goltsman, Eugene; Lapidus, Alla; Hedlund, Brian; Hugenholtz, Phil; Kyrpides, Nikos; Graham, David; Keller, Martin; Wanner, Gerhard; Richardson, Paul; Stetter, Karl O.

    2007-05-01

    Based on conserved cellular properties, all life on Earth can be grouped into different phyla which belong to the primary domains Bacteria, Archaea, and Eukarya. However, tracing back their evolutionary relationships has been impeded by horizontal gene transfer and gene loss. Within the Archaea, the kingdoms Crenarchaeota and Euryarchaeota exhibit a profound divergence. In order to elucidate the evolution of these two major kingdoms, representatives of more deeply diverged lineages would be required. Based on their environmental small subunit ribosomal (ss RNA) sequences, the Korarchaeota had been originally suggested to have an ancestral relationship to all known Archaea although this assessment has been refuted. Here we describe the cultivation and initial characterization of the first member of the Korarchaeota, highly unusual, ultrathin filamentous cells about 0.16 {micro}m in diameter. A complete genome sequence obtained from enrichment cultures revealed an unprecedented combination of signature genes which were thought to be characteristic of either the Crenarchaeota, Euryarchaeota, or Eukarya. Cell division appears to be mediated through a FtsZ-dependent mechanism which is highly conserved throughout the Bacteria and Euryarchaeota. An rpb8 subunit of the DNA-dependent RNA polymerase was identified which is absent from other Archaea and has been described as a eukaryotic signature gene. In addition, the representative organism possesses a ribosome structure typical for members of the Crenarchaeota. Based on its gene complement, this lineage likely diverged near the separation of the two major kingdoms of Archaea. Further investigations of these unique organisms may shed additional light onto the evolution of extant life.

  2. Simulating a Nationally Representative Housing Sample Using EnergyPlus

    SciTech Connect (OSTI)

    Hopkins, Asa S.; Lekov, Alex; Lutz, James; Rosenquist, Gregory; Gu, Lixing

    2011-03-04

    This report presents a new simulation tool under development at Lawrence Berkeley National Laboratory (LBNL). This tool uses EnergyPlus to simulate each single-family home in the Residential Energy Consumption Survey (RECS), and generates a calibrated, nationally representative set of simulated homes whose energy use is statistically indistinguishable from the energy use of the single-family homes in the RECS sample. This research builds upon earlier work by Ritchard et al. for the Gas Research Institute and Huang et al. for LBNL. A representative national sample allows us to evaluate the variance in energy use between individual homes, regions, or other subsamples; using this tool, we can also evaluate how that variance affects the impacts of potential policies. The RECS contains information regarding the construction and location of each sampled home, as well as its appliances and other energy-using equipment. We combined this data with the home simulation prototypes developed by Huang et al. to simulate homes that match the RECS sample wherever possible. Where data was not available, we used distributions, calibrated using the RECS energy use data. Each home was assigned a best-fit location for the purposes of weather and some construction characteristics. RECS provides some detail on the type and age of heating, ventilation, and air-conditioning (HVAC) equipment in each home; we developed EnergyPlus models capable of reproducing the variety of technologies and efficiencies represented in the national sample. This includes electric, gas, and oil furnaces, central and window air conditioners, central heat pumps, and baseboard heaters. We also developed a model of duct system performance, based on in-home measurements, and integrated this with fan performance to capture the energy use of single- and variable-speed furnace fans, as well as the interaction of duct and fan performance with the efficiency of heating and cooling equipment. Comparison with RECS revealed that EnergyPlus did not capture the heating-side behavior of heat pumps particularly accurately, and that our simple oil furnace and boiler models needed significant recalibration to fit with RECS. Simulating the full RECS sample on a single computer would take many hours, so we used the 'cloud computing' services provided by Amazon.com to simulate dozens of homes at once. This enabled us to simulate the full RECS sample, including multiple versions of each home to evaluate the impact of marginal changes, in less than 3 hours. Once the tool was calibrated, we were able to address several policy questions. We made a simple measurement of the heat replacement effect and showed that the net effect of heat replacement on primary energy use is likely to be less than 5%, relative to appliance-only measures of energy savings. Fuel switching could be significant, however. We also evaluated the national and regional impacts of a variety of 'overnight' changes in building characteristics or occupant behavior, including lighting, home insulation and sealing, HVAC system efficiency, and thermostat settings. For example, our model shows that the combination of increased home insulation and better sealed building shells could reduce residential natural gas use by 34.5% and electricity use by 6.5%, and a 1 degree rise in summer thermostat settings could save 2.1% of home electricity use. These results vary by region, and we present results for each U.S. Census division. We conclude by offering proposals for future work to improve the tool. Some proposed future work includes: comparing the simulated energy use data with the monthly RECS bill data; better capturing the variation in behavior between households, especially as it relates to occupancy and schedules; improving the characterization of recent construction and its regional variation; and extending the general framework of this simulation tool to capture multifamily housing units, such as apartment buildings.

  3. Tailored Marketing for Low-income and Under-Represented Population...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Tailored Marketing for Low-income and Under-Represented Population Segments (201) Tailored Marketing for Low-income and Under-Represented Population Segments (201) Better Buildings ...

  4. Examination of Hydrate Formation Methods: Trying to Create Representative Samples

    SciTech Connect (OSTI)

    Kneafsey, T.J.; Rees, E.V.L.; Nakagawa, S.; Kwon, T.-H.

    2011-04-01

    Forming representative gas hydrate-bearing laboratory samples is important so that the properties of these materials may be measured, while controlling the composition and other variables. Natural samples are rare, and have often experienced pressure and temperature changes that may affect the property to be measured [Waite et al., 2008]. Forming methane hydrate samples in the laboratory has been done a number of ways, each having advantages and disadvantages. The ice-to-hydrate method [Stern et al., 1996], contacts melting ice with methane at the appropriate pressure to form hydrate. The hydrate can then be crushed and mixed with mineral grains under controlled conditions, and then compacted to create laboratory samples of methane hydrate in a mineral medium. The hydrate in these samples will be part of the load-bearing frame of the medium. In the excess gas method [Handa and Stupin, 1992], water is distributed throughout a mineral medium (e.g. packed moist sand, drained sand, moistened silica gel, other porous media) and the mixture is brought to hydrate-stable conditions (chilled and pressurized with gas), allowing hydrate to form. This method typically produces grain-cementing hydrate from pendular water in sand [Waite et al., 2004]. In the dissolved gas method [Tohidi et al., 2002], water with sufficient dissolved guest molecules is brought to hydrate-stable conditions where hydrate forms. In the laboratory, this is can be done by pre-dissolving the gas of interest in water and then introducing it to the sample under the appropriate conditions. With this method, it is easier to form hydrate from more soluble gases such as carbon dioxide. It is thought that this method more closely simulates the way most natural gas hydrate has formed. Laboratory implementation, however, is difficult, and sample formation is prohibitively time consuming [Minagawa et al., 2005; Spangenberg and Kulenkampff, 2005]. In another version of this technique, a specified quantity of gas is placed in a sample, then the sample is flooded with water and cooled [Priest et al., 2009]. We have performed a number of tests in which hydrate was formed and the uniformity of the hydrate formation was examined. These tests have primarily used a variety of modifications of the excess gas method to make the hydrate, although we have also used a version of the excess water technique. Early on, we found difficulties in creating uniform samples with a particular sand/ initial water saturation combination (F-110 Sand, {approx} 35% initial water saturation). In many of our tests we selected this combination intentionally to determine whether we could use a method to make the samples uniform. The following methods were examined: Excess gas, Freeze/thaw/form, Freeze/pressurize/thaw, Excess gas followed by water saturation, Excess water, Sand and kaolinite, Use of a nucleation enhancer (SnoMax), and Use of salt in the water. Below, each method, the underlying hypothesis, and our results are briefly presented, followed by a brief conclusion. Many of the hypotheses investigated are not our own, but were presented to us. Much of the data presented is from x-ray CT scanning our samples. The x-ray CT scanner provides a three-dimensional density map of our samples. From this map and the physics that is occurring in our samples, we are able to gain an understanding of the spatial nature of the processes that occur, and attribute them to the locations where they occur.

  5. An analysis of representative heating load lines for residential HSPF ratings

    SciTech Connect (OSTI)

    Rice, C. Keith; Shen, Bo; Shrestha, Som S.

    2015-07-01

    This report describes an analysis to investigate representative heating loads for single-family detached homes using current EnergyPlus simulations (DOE 2014a). Hourly delivered load results are used to determine binned load lines using US Department of Energy (DOE) residential prototype building models (DOE 2014b) developed by Pacific Northwest National Laboratory (PNNL). The selected residential single-family prototype buildings are based on the 2006 International Energy Conservation Code (IECC 2006) in the DOE climate regions. The resulting load lines are compared with the American National Standards Institute (ANSI)/Air-Conditioning, Heating, and Refrigeration Institute (AHRI) Standard 210/240 (AHRI 2008) minimum and maximum design heating requirement (DHR) load lines of the heating seasonal performance factor (HSPF) ratings procedure for each region. The results indicate that a heating load line closer to the maximum DHR load line, and with a lower zero load ambient temperature, is more representative of heating loads predicted for EnergyPlus prototype residential buildings than the minimum DHR load line presently used to determine HSPF ratings. An alternative heating load line equation was developed and compared to binned load lines obtained from the EnergyPlus simulation results. The effect on HSPF of the alternative heating load line was evaluated for single-speed and two-capacity heat pumps, and an average HSPF reduction of 16% was found. The alternative heating load line relationship is tied to the rated cooling capacity of the heat pump based on EnergyPlus autosizing, which is more representative of the house load characteristics than the rated heating capacity. The alternative heating load line equation was found to be independent of climate for the six DOE climate regions investigated, provided an adjustable zero load ambient temperature is used. For Region IV, the default DOE climate region used for HSPF ratings, the higher load line results in an ~28% increase in delivered heating load and an ~52% increase in the estimated heating operating cost over that given in the AHRI directory (AHRI 2014).

  6. Orderings for incomplete factorization preconditioning of nonsymmetric

    Office of Scientific and Technical Information (OSTI)

    problems (Journal Article) | SciTech Connect Orderings for incomplete factorization preconditioning of nonsymmetric problems Citation Details In-Document Search Title: Orderings for incomplete factorization preconditioning of nonsymmetric problems Numerical experiments are presented whereby the effect of reorderings on the convergence of preconditioned Krylov subspace methods for the solution of nonsymmetric linear systems is shown. The preconditioners used in this study are different

  7. U.S. Energy Secretary Steven Chu, U.S. Representatives Larson...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Steven Chu, U.S. Representatives Larson and Courtney to Visit Research Center in East Hartford U.S. Energy Secretary Steven Chu, U.S. Representatives Larson and Courtney to Visit ...

  8. Josh Allen of Richland Operations Office Named 2014 Facility Representative of the Year

    Broader source: Energy.gov [DOE]

    Congratulations to Josh Allen, Richland Operations Office, the winner of the 2014 DOE Facility Representative of the Year Award!

  9. Reducing Power Factor Cost

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Low power factor is expensive and inefficient. Many utility companies charge you an additional fee if your power factor is less than 0.95. Low power factor also reduces your electrical system's distribu- tion capacity by increasing current flow and causing voltage drops. This fact sheet describes power factor and explains how you can improve your power factor to reduce electric bills and enhance your electrical system's capacity. REDUCING POWER FACTOR COST To understand power factor, visualize a

  10. Increases in electric rates in rural areas. Hearing before the Committee on Agriculture, House of Representatives, Ninety-Sixth Congress, Second Session, June 4, 1980

    SciTech Connect (OSTI)

    Not Available

    1980-01-01

    Seven witnesses representing rural electric utilities and cooperatives spoke at a June 4, 1980 hearing to discuss which inflationary factors are increasing rural electric rates. The Committee recognized that the problem is not unique to rural systems. In their testimony, the witnesses noted increasing urbanization of rural areas; the cost of generating plant construction, fuel, and operating expenses; general economic factors of inflation and high interest rates; and regulations as major contributing factors to utility requests for rate increases. The hearing record includes their testimony, additional material submitted for the record, and responses to questions from the subcommittee. (DCK)

  11. The MX Factor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The MX Factor National Security Science Latest Issue:July 2015 past issues All Issues submit The MX Factor Data from atmospheric test films persuaded Department of Defense...

  12. A global approach of the representativity concept: Application on a high-conversion light water reactor MOX lattice case

    SciTech Connect (OSTI)

    Santos, N. D.; Blaise, P.; Santamarina, A.

    2013-07-01

    The development of new types of reactor and the increase in the safety specifications and requirements induce an enhancement in both nuclear data knowledge and a better understanding of the neutronic properties of the new systems. This enhancement is made possible using ad hoc critical mock-up experiments. The main difficulty is to design these experiments in order to obtain the most valuable information. Its quantification is usually made by using representativity and transposition concepts. These theories enable to extract some information about a quantity of interest (an integral parameter) on a configuration, but generally a posteriori. This paper presents a more global approach of this theory, with the idea of optimizing the representativity of a new experiment, and its transposition a priori, based on a multiparametric approach. Using a quadratic sum, we show the possibility to define a global representativity which permits to take into account several quantities of interest at the same time. The maximization of this factor gives information about all quantities of interest. An optimization method of this value in relation to technological parameters (over-clad diameter, atom concentration) is illustrated on a high-conversion light water reactor MOX lattice case. This example tackles the problematic of plutonium experiment for the plutonium aging and a solution through the optimization of both the over-clad and the plutonium content. (authors)

  13. Secretary Chu to Join Representatives Lofgren and Honda at the SLAC

    Energy Savers [EERE]

    National Accelerator Laboratory | Department of Energy Representatives Lofgren and Honda at the SLAC National Accelerator Laboratory Secretary Chu to Join Representatives Lofgren and Honda at the SLAC National Accelerator Laboratory August 13, 2010 - 12:00am Addthis Washington, D.C. - On Monday, U.S. Energy Secretary Steven Chu will visit the SLAC National Accelerator Laboratory in Menlo Park, California. Secretary Chu will join Representatives Zoe Lofgren and Mike Honda and Stanford

  14. Gregory H. Friedman: Before the U.S. House of Representatives Committee on

    Office of Environmental Management (EM)

    Energy and Commerce Subcommittee on Oversight and Investigations | Department of Energy U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations Gregory H. Friedman: Before the U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations May 1, 2002 Before the U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations Statement of Gregory H.

  15. Gregory H. Friedman: Before The U.S. House of Representatives Committee on

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Government Reform Subcommittee on the Federal Workforce and Agency Organization | Department of Energy The U.S. House of Representatives Committee on Government Reform Subcommittee on the Federal Workforce and Agency Organization Gregory H. Friedman: Before The U.S. House of Representatives Committee on Government Reform Subcommittee on the Federal Workforce and Agency Organization April 5 2005 Before The U.S. House of Representatives Committee on Government Reform Subcommittee on the

  16. Gregory H. Friedman: Before the U.S. House Of Representatives Committee on

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy and Commerce Subcommittee on Oversight and Investigations | Department of Energy Of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations Gregory H. Friedman: Before the U.S. House Of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations May 1, 2003 Before the U.S. House Of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations Statement of Gregory H. Friedman,

  17. Gregory H. Friedman: Before the U.S. House of Representatives Committee on

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy and Commerce Subcommittee on Oversight and Investigations | Department of Energy of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations Gregory H. Friedman: Before the U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations February 26, 2003 Before the U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations Statement of Gregory H. Friedman,

  18. Herbert Richardson: Before The U.S. House of Representatives Committee on

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy and Commerce Subcommittee on Oversight and Investigations | Department of Energy Herbert Richardson: Before The U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations Herbert Richardson: Before The U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations March 4, 2004 Before The U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and

  19. 4Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from October to December 2006. Data for these indicators are gathered by Field...

  20. 1Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from January to March 2007. Data for these indicators are gathered by Field elements...

  1. 4Q CY2005 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from October to December 2005. Data for these indicators are gathered by Field...

  2. 2Q CY2005 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from April to June 2005. Data for these indicators are gathered by Field elements...

  3. 3Q CY2005 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from July to September 2005. Data for these indicators are gathered by Field...

  4. 1Q CY2005 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from January to March 2005. Data for these indicators are gathered by Field elements...

  5. 3Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from July to September 2006. Data for these indicators are gathered by Field...

  6. 2Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from April to June 2006. Data for these indicators are gathered by Field elements...

  7. 4Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "Attached is the Facility Representative (FR) Program Performance Indicators QuarterlyReport covering the period from October to December 2007. Data for these indicators aregathered by Field...

  8. 4Q CY2008 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "Attached is the Facility Representative (FR) Program Performance Indicators Quarterly  Report covering the period from October to December   2008. Data for these indicators are  gathered by Field...

  9. 2Q CY2012 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from April through June 2012. Data for these indicators were...

  10. 1Q CY2012 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from January through March 2012. Data for these indicators were...

  11. 4Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from October through December 2011. Data for these indicators were...

  12. 3Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from July to September 2007. Data for these indicators are gathered by Field...

  13. 3Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the Period July  through September 2011. Data for these indicators were gathered...

  14. 4Q CY2010 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "This memorandum summarizes the highlights of the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period October through December 2010. Data for these...

  15. 3Q CY2010 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    This memorandum summarizes the highlights of the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period of July through September 2010. Data for these...

  16. 4Q CY2002 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative Program Performance Indicators (Pis) Quarterly Report Covering the Period from October to December 2002. Data for these indicators are gathered by Field...

  17. 2Q CY2008 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators QuarterlyReport covering the period from April to June 2008. Data for these indicators aregathered by Field elements...

  18. 1Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the Period January through March 2011. Data for these indicators were gathered...

  19. 2Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from April to June 2007. Data for these indicators are gathered by field elements...

  20. 2Q CY2010 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    This memorandum summarizes the highlight of, and announces the availablity on-line of, the Facility Representative (FR) Program Performance Indicators are gathered by Field elements quarterly per...

  1. 3Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    The Facility Representative Program Indicators (Pis) Quarterly Report attached, covering the period from July to September 2000. Data for these indicators are gathered by the Field elements...

  2. 2Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period April through June 20 1 1. Data for these indicators were gathered...

  3. Tailored Marketing for Low-income and Under-Represented Population Segments (201)

    Broader source: Energy.gov [DOE]

    Better Buildings Residential Network Peer Exchange Call Series: Tailored Marketing for Low-Income and Under-Represented Population Segments (201), call slides and discussion summary.

  4. Secretary Chu: China's Clean Energy Successes Represent a New "Sputnik

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Moment" for America | Department of Energy Chu: China's Clean Energy Successes Represent a New "Sputnik Moment" for America Secretary Chu: China's Clean Energy Successes Represent a New "Sputnik Moment" for America November 29, 2010 - 12:00am Addthis Washington, D.C. - In a speech at the National Press Club, U.S Energy Secretary Steven Chu said that the success of China and other countries in clean energy industries represents a new "Sputnik Moment" for the

  5. DOE Orders Self-Study Program - DOE-STD-1063-2011, Facility Representatives

    Office of Environmental Management (EM)

    | Department of Energy 63-2011, Facility Representatives DOE Orders Self-Study Program - DOE-STD-1063-2011, Facility Representatives U.S. Department of Energy Orders Self-Study Program DOE-STD-1063-2011, Facility Representatives Familiar Level - August 2011 The familiar level of this module is divided into three sections. The first section addresses the purpose and scope of DOE-STD-1063-2011, the purpose of the FR program, and the duties, responsibilities, and authorities of FRs and other

  6. 3Q CY2003 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative Program Performance Indicators (PIs) Quarterly Report Covering the Period from July to September  2003. Data for these indicators are gathered by Field...

  7. 4Q CY2004 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report Covering the Period from October to December  2004. Data for these indicators are gathered by Field...

  8. 2Q CY2004 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report Covering the Period from April to June  2004. Data for these indicators are gathered by Field elements...

  9. 4Q CY2003 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative Program Performance Indicators (PIs) Quarterly Report Covering the Period from October to December  2003. Data for these indicators are gathered by Field...

  10. 3Q CY2004 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report Covering the Period from July to September  2004. Data for these indicators are gathered by Field...

  11. 1Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from January  to March 2006. Data for these indicators are gathered by Field...

  12. 3Q CY2009 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative (FR) Program Performance Indicators Quarterly  Report covering the period from July to September 2009. Data for these indicators are gathered by Field...

  13. 4Q CY2009 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "Attached is the Facility Representative (FR) Program Performance Indicators Quarterly  Report covering the period from October to December 2009. Data for these indicators are gathered by Field...

  14. 1Q CY2009 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "Attached is the Facility Representative (FR) Program Performance Indicators Quarterly  Report covering the period from January to March 2009. Data for these indicators are gathered by Field...

  15. 1Q CY2010 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "Attached is the Facility Representative (FR) Program Performance Indicators Quarterly  Report covering the period from January to March2010. Data for these indicators are gathered by Field...

  16. 1Q CY2003 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative Program Performance Indicators (PIs) Quarterly Report Covering the Period from January to March  2003. Data for these indicators are gathered by Field...

  17. 2Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "The Facility Representative Program Performance Indicators (PIs) Quarterly Report is attached, covering the period from April 2000 to June 2000. Data for these indicators are gathered by the Field...

  18. Gregory H. Friedman: Before the U.S. House Of Representatives...

    Office of Environmental Management (EM)

    Gregory H. Friedman: Before the U.S. House Of Representatives Committee on Energy and ... Statement of Gregory H. Friedman, Inspector General U.S. Department of Energy Request to ...

  19. Gregory H. Friedman: Before the U.S. House of Representatives...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Gregory H. Friedman: Before the U.S. House of Representatives Committee on Energy and ... Statement of Gregory H. Friedman, Inspector General U.S. Department of Energy Testify on ...

  20. 2Q CY2009 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "Attached is the Facility Representative (FR) Program Performance Indicators Quarterly  Report covering the period from April to June  2009. Data for these indicators are gathered by Field elements...

  1. 2Q CY2003 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    Attached is the Facility Representative Program Performance Indicators (PIs) Quarterly Report Covering the Period from April to June  2003. Data for these indicators are gathered by Field elements...

  2. 3Q C&2008 (PDF), Facility Representative Program Performance Indicators Quarterly Report

    Broader source: Energy.gov [DOE]

    "Attached is the Facility Representative (FR) Program Performance Indicators Quarterly  Report covering the period from July to September   2008. Data for these indicators aregathered by Field...

  3. August 20, 2014 meeting with DOE representatives regarding the remand of

    Energy Savers [EERE]

    the DOE Direct Final Rule as it relates to efficiency standards for non-weatherized gas furnaces | Department of Energy August 20, 2014 meeting with DOE representatives regarding the remand of the DOE Direct Final Rule as it relates to efficiency standards for non-weatherized gas furnaces August 20, 2014 meeting with DOE representatives regarding the remand of the DOE Direct Final Rule as it relates to efficiency standards for non-weatherized gas furnaces This memorandum provides an overview

  4. Gregory H. Friedman: Before the U.S. House of Representatives Committee on

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy and Commerce Subcommittee on Oversight and Investigations | Department of Energy Energy and Commerce Subcommittee on Oversight and Investigations Gregory H. Friedman: Before the U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations April 5, 2005 Before the U.S. House of Representatives Committee on Energy and Commerce Subcommittee on Oversight and Investigations Statement of Gregory H. Friedman, Inspector General U.S. Department of

  5. Gregory H. Friedman: Before the U.S. House of Representatives Committee on

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Government Reform | Department of Energy Government Reform Gregory H. Friedman: Before the U.S. House of Representatives Committee on Government Reform March 20, 2003 Before the U.S. House of Representatives Committee on Government Reform Statement of Gregory H. Friedman Inspector General, U.S. Department of Energy Request to testify on the Department of Energy's (Department) contract administration activities. The Department is one of the most contractor dependent agencies in the Federal

  6. Characterization of Representative Materials in Support of Safe, Long Term Storage of Surplus Plutonium in DOE-STD-3013 Containers

    SciTech Connect (OSTI)

    Narlesky, Joshua E.; Stroud, Mary Ann; Smith, Paul Herrick; Wayne, David M.; Mason, Richard E.; Worl, Laura A.

    2013-02-15

    The Surveillance and Monitoring Program is a joint Los Alamos National Laboratory/Savannah River Site effort funded by the Department of Energy-Environmental Management to provide the technical basis for the safe, long-term storage (up to 50 years) of over 6 metric tons of plutonium stored in over 5,000 DOE-STD-3013 containers at various facilities around the DOE complex. The majority of this material is plutonium that is surplus to the nuclear weapons program, and much of it is destined for conversion to mixed oxide fuel for use in US nuclear power plants. The form of the plutonium ranges from relatively pure metal and oxide to very impure oxide. The performance of the 3013 containers has been shown to depend on moisture content and on the levels, types and chemical forms of the impurities. The oxide materials that present the greatest challenge to the storage container are those that contain chloride salts. Other common impurities include oxides and other compounds of calcium, magnesium, iron, and nickel. Over the past 15 years the program has collected a large body of experimental data on 54 samples of plutonium, with 53 chosen to represent the broader population of materials in storage. This paper summarizes the characterization data, moisture analysis, particle size, surface area, density, wattage, actinide composition, trace element impurity analysis, and shelf life surveillance data and includes origin and process history information. Limited characterization data on fourteen nonrepresentative samples is also presented.

  7. WHAT THE SMART GRID MEANS TO YOU AND THE PEOPLE YOU REPRESENT. | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy THE SMART GRID MEANS TO YOU AND THE PEOPLE YOU REPRESENT. WHAT THE SMART GRID MEANS TO YOU AND THE PEOPLE YOU REPRESENT. The U.S. Department of Energy (DOE) is charged under the Energy Independence and Security Act of 2007 (EISA 2007) with modernizing the nation's electricity grid to improve its reliability and efficiency. As part of this effort, DOE is also responsible for increasing awareness of our nation's Smart Grid. Building upon The Smart Grid: An Introduction, a

  8. Dy-Mn-Si as a representative of family of 'Dy-Transition

    Office of Scientific and Technical Information (OSTI)

    Metal-Si' systems: Its isothermal sections, empirical rProd. Type: FTPules and new rare-earth manganese silicides (Journal Article) | SciTech Connect Dy-Mn-Si as a representative of family of 'Dy-Transition Metal-Si' systems: Its isothermal sections, empirical rProd. Type: FTPules and new rare-earth manganese silicides Citation Details In-Document Search Title: Dy-Mn-Si as a representative of family of 'Dy-Transition Metal-Si' systems: Its isothermal sections, empirical rProd. Type: FTPules

  9. The Dy-Ni-Si system as a representative of the rare earth-Ni-Si

    Office of Scientific and Technical Information (OSTI)

    family: Its isothermal section and new rare-earth nickel silicides (Journal Article) | SciTech Connect SciTech Connect Search Results Journal Article: The Dy-Ni-Si system as a representative of the rare earth-Ni-Si family: Its isothermal section and new rare-earth nickel silicides Citation Details In-Document Search Title: The Dy-Ni-Si system as a representative of the rare earth-Ni-Si family: Its isothermal section and new rare-earth nickel silicides The Dy-Ni-Si system has been

  10. U.S. Energy Secretary Steven Chu, U.S. Representatives Larson and Courtney

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    to Visit Research Center in East Hartford | Department of Energy Steven Chu, U.S. Representatives Larson and Courtney to Visit Research Center in East Hartford U.S. Energy Secretary Steven Chu, U.S. Representatives Larson and Courtney to Visit Research Center in East Hartford February 3, 2011 - 12:00am Addthis WASHINGTON, DC - Tomorrow, Friday, February 4, U.S. Secretary of Energy Steven Chu will travel to East Hartford, Conn. to visit United Technologies Research Center, which has received

  11. Fact #734: July 2, 2012 OPEC Countries Represent Less Than Half of U.S.

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Petroleum Imports | Department of Energy 4: July 2, 2012 OPEC Countries Represent Less Than Half of U.S. Petroleum Imports Fact #734: July 2, 2012 OPEC Countries Represent Less Than Half of U.S. Petroleum Imports Even though Saudi Arabia is the world's largest producer of petroleum, and OPEC countries produce much of the oil in the global market, the U.S. imports most of its oil from Canada, Mexico and other non-OPEC countries. Petroleum imports from Canada have been increasing since the

  12. DOE Honors WIPP Representative for Cutting Travel Costs, Greenhouse Gas Emissions

    Broader source: Energy.gov [DOE]

    WASHINGTON, D.C. – A representative of the Waste Isolation Pilot Plant (WIPP) near Carlsbad, N.M., on Tuesday received the Secretary of Energy’s Appreciation Award for her efforts to improve sustainability and reduce travel costs and the number of fleet vehicles.

  13. Mechanism-based Representative Volume Elements (RVEs) for Predicting Property Degradations in Multiphase Materials

    SciTech Connect (OSTI)

    Xu, Wei; Sun, Xin; Li, Dongsheng; Ryu, Seun; Khaleel, Mohammad A.

    2013-02-01

    Quantitative understanding of the evolving thermal-mechanical properties of a multi-phase material hinges upon the availability of quantitative statistically representative microstructure descriptions. Questions then arise as to whether a two-dimensional (2D) or a three-dimensional (3D) representative volume element (RVE) should be considered as the statistically representative microstructure. Although 3D models are more representative than 2D models in general, they are usually computationally expensive and difficult to be reconstructed. In this paper, we evaluate the accuracy of a 2D RVE in predicting the property degradations induced by different degradation mechanisms with the multiphase solid oxide fuel cell (SOFC) anode material as an example. Both 2D and 3D microstructure RVEs of the anodes are adopted to quantify the effects of two different degradation mechanisms: humidity-induced electrochemical degradation and phosphorus poisoning induced structural degradation. The predictions of the 2D model are then compared with the available experimental measurements and the results from the 3D model. It is found that the 2D model, limited by its inability of reproducing the realistic electrical percolation, is unable to accurately predict the degradation of thermo-electrical properties. On the other hand, for the phosphorus poisoning induced structural degradation, both 2D and 3D microstructures yield similar results, indicating that the 2D model is capable of providing computationally efficient yet accurate results for studying the structural degradation within the anodes.

  14. The MX Factor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MX Factor Test films played a strategic-planning role in the debates of the late 1970s and early 1980s about where and how to deploy the MX intercontinental ballistic missile...

  15. FGF growth factor analogs

    DOE Patents [OSTI]

    Zamora, Paul O.; Pena, Louis A.; Lin, Xinhua; Takahashi, Kazuyuki

    2012-07-24

    The present invention provides a fibroblast growth factor heparin-binding analog of the formula: ##STR00001## where R.sub.1, R.sub.2, R.sub.3, R.sub.4, R.sub.5, X, Y and Z are as defined, pharmaceutical compositions, coating compositions and medical devices including the fibroblast growth factor heparin-binding analog of the foregoing formula, and methods and uses thereof.

  16. Expression of transforming growth factor alpha in plutonium-239-induced lung neoplasms in dogs: investigations of autocrine mechanisms of growth

    SciTech Connect (OSTI)

    Gillett, N.A.; Stegelmeier, B.L.; Chang, I.Y.; Kelly, G. )

    1991-06-01

    We have previously shown that 47% of radiation-induced lung neoplasms in dogs exhibit increased expression of epidermal growth factor receptor (EGFR). In this study, we investigated the expression of transforming growth factor alpha (TGF-alpha), a ligand for EGFR, to determine if an autocrine mechanism for growth stimulation was present in these tumors. As determined by immunohistochemistry, 59% (26/44) of the lung neoplasms examined had increased expression of TGF-alpha. Expression of TGF-alpha was not related to the etiology of the tumor, e.g., spontaneous or plutonium-induced; however, it was related to the phenotype of the tumor. Statistical analysis of the correlation of EGFR and TGF-alpha expression within the same tumor did not show a positive association; however, specific phenotypes did have statistically significant expression of EGFR or TGF-alpha, suggesting that overexpression of either the ligand or its receptor conferred a growth advantage to the neoplasm. Twenty-seven percent (32/117) of radiation-induced proliferative epithelial foci expressed TGF-alpha, and a portion of those foci (8/32) expressed both EGFR and TGF-alpha. This supports the hypothesis that these foci represent preneoplastic lesions, and suggests that those foci exhibiting increased expression of the growth factor or its receptor are at greater risk for progressing to neoplasia.

  17. Polytechnic Institute of New York University Researchers Represented in the E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Polytechnic Institute of New York University Researchers Represented in the E-print Network Researcher/Research Institution Web page Aronov, Boris - Department of Computer Science and Engineering, Polytechnic Institute of New York University http://cis.poly.edu/~aronov/research. html Brönnimann, Hervé - Department of Computer Science and Engineering, Polytechnic Institute of New York University http://photon.poly.edu/~hbr/publis. html Chiang, Yi-Jen - Department of Computer Science and

  18. On October 20, 2011, representatives of Howe Corporation, Gade Environmental, an

    Energy Savers [EERE]

    October 20, 2011, representatives of Howe Corporation, Gade Environmental, and Beecon ProfServe met with DOE to discuss the proposed rules EERE-2010 BT-TP-0036 RIN 1904-AC38 Energy Efficiency Program for Certain Commercial and Industrial Equipment: Test Procedures for Commercial Ice Makers. The meeting was held at the request of Howe Corporation at the DOE offices in Washington DC. In attendance: Ari Altman, DOE Ashley Armstrong, DOE Robert Bittner, Beecon ProfServe John Cymbalsky, DOE Mary

  19. WHAT THE SMART GRID MEANS TO YOU AND THE PEOPLE YOU REPRESENT.

    Broader source: Energy.gov (indexed) [DOE]

    REPRESENT. regulators consumer advocates environmental groups technology providers policymakers ONE of SIX SMART GRID STAKEHOLDER BOOKS A smarter grid can work harder and more efficiently to respond to the needs of all consumers, contain costs and enable clean-energy solutions at scale. regulators utilities 2 DISCLAIMER PRINTED IN THE UNITED STATES OF AMERICA. This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States

  20. DOE-STD-1151-2002; Facility Representative Functional Area Qualification Standard

    Office of Environmental Management (EM)

    1151-2002 April 2002 DOE STANDARD FACILITY REPRESENTATIVE FUNCTIONAL AREA QUALIFICATION STANDARD DOE Defense Nuclear Facilities Technical Personnel U.S. Department of Energy AREA TRNG Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced from the best available copy. Available to DOE and DOE contractors from ES&H Technical Information Services, U.S. Department of Energy, (800) 473-4375, fax: (301) 903-9823.

  1. 100% MOX BWR experimental program design using multi-parameter representative

    SciTech Connect (OSTI)

    Blaise, P.; Fougeras, P.; Cathalau, S.

    2012-07-01

    A new multiparameter representative approach for the design of Advanced full MOX BWR core physics experimental programs is developed. The approach is based on sensitivity analysis of integral parameters to nuclear data, and correlations among different integral parameters. The representativeness method is here used to extract a quantitative relationship between a particular integral response of an experimental mock-up and the same response in a reference project to be designed. The study is applied to the design of the 100% MOX BASALA ABWR experimental program in the EOLE facility. The adopted scheme proposes an original approach to the problem, going from the initial 'microscopic' pin-cells integral parameters to the whole 'macroscopic' assembly integral parameters. This approach enables to collect complementary information necessary to optimize the initial design and to meet target accuracy on the integral parameters to be measured. The study has demonstrated the necessity of new fuel pins fabrication, fulfilling minimal costs requirements, to meet acceptable representativeness on local power distribution. (authors)

  2. Uniprocessor Performance Analysis of a Representative Workload of Sandia National Laboratories' Scientific Applications.

    SciTech Connect (OSTI)

    Charles Laverty

    2005-10-01

    UNIPROCESSOR PERFORMANCE ANALYSIS OF A REPRESENTATIVE WORKLOAD OF SANDIA NATIONAL LABORATORIES' SCIENTIFIC APPLICATIONS Master of Science in Electrical Engineering New Mexico State University Las Cruces, New Mexico, 2005 Dr. Jeanine Cook, Chair Throughout the last decade computer performance analysis has become absolutely necessary to maximum performance of some workloads. Sandia National Laboratories (SNL) located in Albuquerque, New Mexico is no different in that to achieve maximum performance of large scientific, parallel workloads performance analysis is needed at the uni-processor level. A representative workload has been chosen as the basis of a computer performance study to determine optimal processor characteristics in order to better specify the next generation of supercomputers. Cube3, a finite element test problem developed at SNL is a representative workload of their scientific workloads. This workload has been studied at the uni-processor level to understand characteristics in the microarchitecture that will lead to the overall performance improvement at the multi-processor level. The goal of studying vthis workload at the uni-processor level is to build a performance prediction model that will be integrated into a multi-processor performance model which is currently being developed at SNL. Through the use of performance counters on the Itanium 2 microarchitecture, performance statistics are studied to determine bottlenecks in the microarchitecture and/or changes in the application code that will maximize performance. From source code analysis a performance degrading loop kernel was identified and through the use of compiler optimizations a performance gain of around 20% was achieved.

  3. Douglas Factors | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Douglas Factors Douglas Factors The Merit Systems Protection Board in its landmark decision, Douglas vs. Veterans Administration, 5 MSPR 280, established criteria that supervisors must consider in determining an appropriate penalty to impose for an act of employee misconduct. These twelve factors are commonly referred to as "Douglas Factors". PDF icon The Douglas Factors More Documents & Publications Douglas Factors NETL AFGE 1995 Douglas Factors NETL AFGE 1104 VBH-0060 - In the

  4. Multi-factor authentication

    DOE Patents [OSTI]

    Hamlet, Jason R; Pierson, Lyndon G

    2014-10-21

    Detection and deterrence of spoofing of user authentication may be achieved by including a cryptographic fingerprint unit within a hardware device for authenticating a user of the hardware device. The cryptographic fingerprint unit includes an internal physically unclonable function ("PUF") circuit disposed in or on the hardware device, which generates a PUF value. Combining logic is coupled to receive the PUF value, combines the PUF value with one or more other authentication factors to generate a multi-factor authentication value. A key generator is coupled to generate a private key and a public key based on the multi-factor authentication value while a decryptor is coupled to receive an authentication challenge posed to the hardware device and encrypted with the public key and coupled to output a response to the authentication challenge decrypted with the private key.

  5. Geothermal Plant Capacity Factors

    SciTech Connect (OSTI)

    Greg Mines; Jay Nathwani; Christopher Richard; Hillary Hanson; Rachel Wood

    2015-01-01

    The capacity factors recently provided by the Energy Information Administration (EIA) indicated this plant performance metric had declined for geothermal power plants since 2008. Though capacity factor is a term commonly used by geothermal stakeholders to express the ability of a plant to produce power, it is a term frequently misunderstood and in some instances incorrectly used. In this paper we discuss how this capacity factor is defined and utilized by the EIA, including discussion on the information that the EIA requests from operations in their 923 and 860 forms that are submitted both monthly and annually by geothermal operators. A discussion is also provided regarding the entities utilizing the information in the EIA reports, and how those entities can misinterpret the data being supplied by the operators. The intent of the paper is to inform the facility operators as the importance of the accuracy of the data that they provide, and the implications of not providing the correct information.

  6. Radiation View Factor With Shadowing

    Energy Science and Technology Software Center (OSTI)

    1992-02-24

    FACET calculates the radiation geometric view factor (alternatively called shape factor, angle factor, or configuration factor) between surfaces for axisymmetric, two-dimensional planar and three-dimensional geometries with interposed third surface obstructions. FACET was developed to calculate view factors as input data to finite element heat transfer analysis codes.

  7. Inelastic Scattering Form Factors

    Energy Science and Technology Software Center (OSTI)

    1992-01-01

    ATHENA-IV computes form factors for inelastic scattering calculations, using single-particle wave functions that are eigenstates of motion in either a Woods-Saxon potential well or a harmonic oscillator well. Two-body forces of Gauss, Coulomb, Yukawa, and a sum of cut-off Yukawa radial dependences are available.

  8. ERYTHROPOIETIC FACTOR PURIFICATION

    DOE Patents [OSTI]

    White, W.F.; Schlueter, R.J.

    1962-05-01

    A method is given for purifying and concentrating the blood plasma erythropoietic factor. Anemic sheep plasma is contacted three times successively with ion exchange resins: an anion exchange resin, a cation exchange resin at a pH of about 5, and a cation exchange resin at a pH of about 6. (AEC)

  9. Accountable Property Representatives List and Property Pass Signer List by Organization, December 2, 2015

    Broader source: Energy.gov (indexed) [DOE]

    Accountable Property Representatives/Property Pass Authorization 12/2/2015 Employee Authorized Organization Phone APR Primary Property Pass Signer PETEET, LISA J. ALL ORGS (202) 287-5496 √ AGEE, PATTIE M. EM-40 (202) 586-9417 √ AMES, RUSSELL SC-32 (202) 586-1082 √ √ ANDERSON, SUE EM-73 (301) 903-8368 √ √ ATKINSON-HYMAN, DEBRA PA-1 (202) 586-2461 √ √ AUGUSTYN, ANN HG-6 (202) 287-1528 √ BARLETT, DENNIS EE-3C (202) 586-0874 √ BARNES, CLAUDE GC-90 (202) 586-2957 √ √

  10. W&M Student Elected to Represent American Physical Society's Graduate

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Student Forum | Jefferson Lab W&M Student Elected to Represent American Physical Society's Graduate Student Forum V Gray Valerie Gray, a graduate student at The College of William and Mary and a researcher at the Department of Energy's Thomas Jefferson National Accelerator Facility, was chosen this year by American Physical Society members as chair-elect for the APS Forum on Graduate Student Affairs. NEWPORT NEWS, VA, Aug. 8, 2014 - The old adage "If you want something done, give it

  11. Sampling device for withdrawing a representative sample from single and multi-phase flows

    DOE Patents [OSTI]

    Apley, Walter J. (Pasco, WA); Cliff, William C. (Richland, WA); Creer, James M. (Richland, WA)

    1984-01-01

    A fluid stream sampling device has been developed for the purpose of obtaining a representative sample from a single or multi-phase fluid flow. This objective is carried out by means of a probe which may be inserted into the fluid stream. Individual samples are withdrawn from the fluid flow by sampling ports with particular spacings, and the sampling parts are coupled to various analytical systems for characterization of the physical, thermal, and chemical properties of the fluid flow as a whole and also individually.

  12. Accountable Property Representatives List and Property Pass Signer List by Organization, March 7, 2016

    Energy Savers [EERE]

    Accountable Property Representatives/Property Pass Authorization 3/7/2016 Employee Authorized Organization Phone APR Primary Property Pass Signer PETEET, LISA J. ALL ORGS (202) 287-5496 √ AGEE, PATTIE M. EM-40 (202) 586-9417 √ AMES, RUSSELL SC-32 (202) 586-1082 √ √ ANDERSON, SUE EM-73 (301) 903-8368 √ √ ATKINSON-HYMAN, DEBRA PA-1 (202) 586-2461 √ √ AUGUSTYN, ANN HG-6 (202) 287-1528 √ BARLETT, DENNIS EE-3C (202) 586-0874 √ BARNES, CLAUDE GC-90 (202) 586-2957 √ √

  13. Facility Representatives, DOE-STD-1063-2011, Change Notice 1

    Office of Environmental Management (EM)

    STD-1063-2011 February 2011 Change Notice 1 March 2012 DOE STANDARD FACILITY REPRESENTATIVES U.S. Department of Energy AREA MGMT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. DOE-STD-1063-2011 ii Change Notice No. 1 March 2012 Table of Changes Available on the Department of Energy Technical Standards Program Web site at http://www.hss.doe.gov/nuclearsafety/ns/techstds/ Page/Section Change Foreword Update contact information and internet

  14. Ex Parte Memo on ULE Policy Statement and Conversion Factor Rulemaking |

    Energy Savers [EERE]

    Department of Energy Memo on ULE Policy Statement and Conversion Factor Rulemaking Ex Parte Memo on ULE Policy Statement and Conversion Factor Rulemaking On December 1, 2015, AHRI staff and water heater manufacturer representatives met with representatives from the Department of Energy (DOE) to discuss the enforcement policy statement issued on October 2, 2015, regarding consumer water heaters and certain commercial water heating equipment, (Enforcement Guidance),1 as well as the proposed

  15. An estimated 5% of new protein structures solved today represent a new Pfam family

    SciTech Connect (OSTI)

    Mistry, Jaina; Kloppmann, Edda; Rost, Burkhard; Punta, Marco

    2013-11-01

    This study uses the Pfam database to show that the sequence redundancy of protein structures deposited in the PDB is increasing. The possible reasons behind this trend are discussed. High-resolution structural knowledge is key to understanding how proteins function at the molecular level. The number of entries in the Protein Data Bank (PDB), the repository of all publicly available protein structures, continues to increase, with more than 8000 structures released in 2012 alone. The authors of this article have studied how structural coverage of the protein-sequence space has changed over time by monitoring the number of Pfam families that acquired their first representative structure each year from 1976 to 2012. Twenty years ago, for every 100 new PDB entries released, an estimated 20 Pfam families acquired their first structure. By 2012, this decreased to only about five families per 100 structures. The reasons behind the slower pace at which previously uncharacterized families are being structurally covered were investigated. It was found that although more than 50% of current Pfam families are still without a structural representative, this set is enriched in families that are small, functionally uncharacterized or rich in problem features such as intrinsically disordered and transmembrane regions. While these are important constraints, the reasons why it may not yet be time to give up the pursuit of a targeted but more comprehensive structural coverage of the protein-sequence space are discussed.

  16. Derivation of dose conversion factors for tritium

    SciTech Connect (OSTI)

    Killough, G. G.

    1982-03-01

    For a given intake mode (ingestion, inhalation, absorption through the skin), a dose conversion factor (DCF) is the committed dose equivalent to a specified organ of an individual per unit intake of a radionuclide. One also may consider the effective dose commitment per unit intake, which is a weighted average of organ-specific DCFs, with weights proportional to risks associated with stochastic radiation-induced fatal health effects, as defined by Publication 26 of the International Commission on Radiological Protection (ICRP). This report derives and tabulates organ-specific dose conversion factors and the effective dose commitment per unit intake of tritium. These factors are based on a steady-state model of hydrogen in the tissues of ICRP's Reference Man (ICRP Publication 23) and equilibrium of specific activities between body water and other tissues. The results differ by 27 to 33% from the estimate on which ICRP Publication 30 recommendations are based. The report also examines a dynamic model of tritium retention in body water, mineral bone, and two compartments representing organically-bound hydrogen. This model is compared with data from human subjects who were observed for extended periods. The manner of combining the dose conversion factors with measured or model-predicted levels of contamination in man's exposure media (air, drinking water, soil moisture) to estimate dose rate to an individual is briefly discussed.

  17. Anthrax Lethal Factor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Thiang Yian Wong, Robert Schwarzenbacher and Robert C. Liddington The Burnham Institute, 10901 North Torrey Pines Road, La Jolla, CA 92037. Anthrax Toxin is a major virulence factor in the infectious disease, Anthrax1. This toxin is produced by Bacillus anthracis, which is an encapsulated, spore-forming, rod-shaped bacterium. Inhalation anthrax, the most deadly form, is contracted through breathing spores. Once spores germinate within cells of the immune system called macrophages2, bacterial

  18. Meeting the Radiative Forcing Targets of the Representative Concentration Pathways in a World with Agricultural Climate Impacts

    SciTech Connect (OSTI)

    Kyle, G. Page; Mueller, C.; Calvin, Katherine V.; Thomson, Allison M.

    2014-02-28

    This study assesses how climate impacts on agriculture may change the evolution of the agricultural and energy systems in meeting the end-of-century radiative forcing targets of the Representative Concentration Pathways (RCPs). We build on the recently completed ISI-MIP exercise that has produced global gridded estimates of future crop yields for major agricultural crops using climate model projections of the RCPs from the Coupled Model Intercomparison Project Phase 5 (CMIP5). For this study we use the bias-corrected outputs of the HadGEM2-ES climate model as inputs to the LPJmL crop growth model, and the outputs of LPJmL to modify inputs to the GCAM integrated assessment model. Our results indicate that agricultural climate impacts generally lead to an increase in global cropland, as compared with corresponding emissions scenarios that do not consider climate impacts on agricultural productivity. This is driven mostly by negative impacts on wheat, rice, other grains, and oil crops. Still, including agricultural climate impacts does not significantly increase the costs or change the technological strategies of global, whole-system emissions mitigation. In fact, to meet the most aggressive climate change mitigation target (2.6 W/m2 in 2100), the net mitigation costs are slightly lower when agricultural climate impacts are considered. Key contributing factors to these results are (a) low levels of climate change in the low-forcing scenarios, (b) adaptation to climate impacts, simulated in GCAM through inter-regional shifting in the production of agricultural goods, and (c) positive average climate impacts on bioenergy crop yields.

  19. Representing the thermal state in time-dependent density functional theory

    SciTech Connect (OSTI)

    Modine, N. A.; Hatcher, R. M.

    2015-05-28

    Classical molecular dynamics (MD) provides a powerful and widely used approach to determining thermodynamic properties by integrating the classical equations of motion of a system of atoms. Time-Dependent Density Functional Theory (TDDFT) provides a powerful and increasingly useful approach to integrating the quantum equations of motion for a system of electrons. TDDFT efficiently captures the unitary evolution of a many-electron state by mapping the system into a fictitious non-interacting system. In analogy to MD, one could imagine obtaining the thermodynamic properties of an electronic system from a TDDFT simulation in which the electrons are excited from their ground state by a time-dependent potential and then allowed to evolve freely in time while statistical data are captured from periodic snapshots of the system. For a variety of systems (e.g., many metals), the electrons reach an effective state of internal equilibrium due to electron-electron interactions on a time scale that is short compared to electron-phonon equilibration. During the initial time-evolution of such systems following electronic excitation, electron-phonon interactions should be negligible, and therefore, TDDFT should successfully capture the internal thermalization of the electrons. However, it is unclear how TDDFT represents the resulting thermal state. In particular, the thermal state is usually represented in quantum statistical mechanics as a mixed state, while the occupations of the TDDFT wavefunctions are fixed by the initial state in TDDFT. We work to address this puzzle by (A) reformulating quantum statistical mechanics so that thermodynamic expectations can be obtained as an unweighted average over a set of many-body pure states and (B) constructing a family of non-interacting (single determinant) TDDFT states that approximate the required many-body states for the canonical ensemble.

  20. A Subbasin-based framework to represent land surface processes in an Earth System Model

    SciTech Connect (OSTI)

    Tesfa, Teklu K.; Li, Hongyi; Leung, Lai-Yung R.; Huang, Maoyi; Ke, Yinghai; Sun, Yu; Liu, Ying

    2014-05-20

    Realistically representing spatial heterogeneity and lateral land surface processes within and between modeling units in earth system models is important because of their implications to surface energy and water exchange. The traditional approach of using regular grids as computational units in land surface models and earth system models may lead to inadequate representation of lateral movements of water, energy and carbon fluxes, especially when the grid resolution increases. Here a new subbasin-based framework is introduced in the Community Land Model (CLM), which is the land component of the Community Earth System Model (CESM). Local processes are represented assuming each subbasin as a grid cell on a pseudo grid matrix with no significant modifications to the existing CLM modeling structure. Lateral routing of water within and between subbasins is simulated with the subbasin version of a recently-developed physically based routing model, Model for Scale Adaptive River Routing (MOSART). As an illustration, this new framework is implemented in the topographically diverse region of the U.S. Pacific Northwest. The modeling units (subbasins) are delineated from high-resolution Digital Elevation Model while atmospheric forcing and surface parameters are remapped from the corresponding high resolution datasets. The impacts of this representation on simulating hydrologic processes are explored by comparing it with the default (grid-based) CLM representation. In addition, the effects of DEM resolution on parameterizing topography and the subsequent effects on runoff processes are investigated. Limited model evaluation and comparison showed that small difference between the averaged forcing can lead to more significant difference in the simulated runoff and streamflow because of nonlinear horizontal processes. Topographic indices derived from high resolution DEM may not improve the overall water balance, but affect the partitioning between surface and subsurface runoff. More systematic analyses are needed to determine the relative merits of the subbasin representation compared to the commonly used grid-based representation, especially when land surface models are approaching higher resolutions.

  1. The MX Factor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MX Factor Test films played a strategic-planning role in the debates of the late 1970s and early 1980s about where and how to deploy the MX intercontinental ballistic missile (LGM-118 Peacekeeper). The deployment would have to ensure that the missiles could survive a first strike by an adversary. Military planners were considering placing the missiles in clusters of hardened concrete shelters in the hot, dry Great Basin Desert of Nevada and Utah. Films of atmospheric tests at the Nevada Test

  2. Representing the thermal state in time-dependent density functional theory

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Modine, N. A.; Hatcher, R. M.

    2015-05-28

    Classical molecular dynamics (MD) provides a powerful and widely used approach to determining thermodynamic properties by integrating the classical equations of motion of a system of atoms. Time-Dependent Density Functional Theory (TDDFT) provides a powerful and increasingly useful approach to integrating the quantum equations of motion for a system of electrons. TDDFT efficiently captures the unitary evolution of a many-electron state by mapping the system into a fictitious non-interacting system. In analogy to MD, one could imagine obtaining the thermodynamic properties of an electronic system from a TDDFT simulation in which the electrons are excited from their ground state bymore »a time-dependent potential and then allowed to evolve freely in time while statistical data are captured from periodic snapshots of the system. For a variety of systems (e.g., many metals), the electrons reach an effective state of internal equilibrium due to electron-electron interactions on a time scale that is short compared to electron-phonon equilibration. During the initial time-evolution of such systems following electronic excitation, electron-phonon interactions should be negligible, and therefore, TDDFT should successfully capture the internal thermalization of the electrons. However, it is unclear how TDDFT represents the resulting thermal state. In particular, the thermal state is usually represented in quantum statistical mechanics as a mixed state, while the occupations of the TDDFT wave functions are fixed by the initial state in TDDFT. Two key questions involve (1) reformulating quantum statistical mechanics so that thermodynamic expectations can be obtained as an unweighted average over a set of many-body pure states and (2) constructing a family of non-interacting (single determinant) TDDFT states that approximate the required many-body states for the canonical ensemble. In Section II, we will address these questions by first demonstrating that thermodynamic expectations can be evaluated by averaging over certain many-body pure states, which we will call thermal states, and then constructing TDDFT states that approximate these thermal states. In Section III, we will present some numerical tests of the resulting theory, and in Section IV, we will summarize our main results and discuss some possible future directions for this work.« less

  3. Representing the thermal state in time-dependent density functional theory

    SciTech Connect (OSTI)

    Modine, N. A.; Hatcher, R. M.

    2015-05-28

    Classical molecular dynamics (MD) provides a powerful and widely used approach to determining thermodynamic properties by integrating the classical equations of motion of a system of atoms. Time-Dependent Density Functional Theory (TDDFT) provides a powerful and increasingly useful approach to integrating the quantum equations of motion for a system of electrons. TDDFT efficiently captures the unitary evolution of a many-electron state by mapping the system into a fictitious non-interacting system. In analogy to MD, one could imagine obtaining the thermodynamic properties of an electronic system from a TDDFT simulation in which the electrons are excited from their ground state by a time-dependent potential and then allowed to evolve freely in time while statistical data are captured from periodic snapshots of the system. For a variety of systems (e.g., many metals), the electrons reach an effective state of internal equilibrium due to electron-electron interactions on a time scale that is short compared to electron-phonon equilibration. During the initial time-evolution of such systems following electronic excitation, electron-phonon interactions should be negligible, and therefore, TDDFT should successfully capture the internal thermalization of the electrons. However, it is unclear how TDDFT represents the resulting thermal state. In particular, the thermal state is usually represented in quantum statistical mechanics as a mixed state, while the occupations of the TDDFT wave functions are fixed by the initial state in TDDFT. Two key questions involve (1) reformulating quantum statistical mechanics so that thermodynamic expectations can be obtained as an unweighted average over a set of many-body pure states and (2) constructing a family of non-interacting (single determinant) TDDFT states that approximate the required many-body states for the canonical ensemble. In Section II, we will address these questions by first demonstrating that thermodynamic expectations can be evaluated by averaging over certain many-body pure states, which we will call thermal states, and then constructing TDDFT states that approximate these thermal states. In Section III, we will present some numerical tests of the resulting theory, and in Section IV, we will summarize our main results and discuss some possible future directions for this work.

  4. Clustering method and representative feeder selection for the California solar initiative

    SciTech Connect (OSTI)

    Broderick, Robert Joseph; Williams, Joseph R.; Munoz-Ramos, Karina

    2014-02-01

    The screening process for DG interconnection procedures needs to be improved in order to increase the PV deployment level on the distribution grid. A significant improvement in the current screening process could be achieved by finding a method to classify the feeders in a utility service territory and determine the sensitivity of particular groups of distribution feeders to the impacts of high PV deployment levels. This report describes the utility distribution feeder characteristics in California for a large dataset of 8,163 feeders and summarizes the California feeder population including the range of characteristics identified and most important to hosting capacity. The report describes the set of feeders that are identified for modeling and analysis as well as feeders identified for the control group. The report presents a method for separating a utilitys distribution feeders into unique clusters using the k-means clustering algorithm. An approach for determining the feeder variables of interest for use in a clustering algorithm is also described. The report presents an approach for choosing the feeder variables to be utilized in the clustering process and a method is identified for determining the optimal number of representative clusters.

  5. A Control Chart Approach for Representing and Mining Data Streams with Shape Based Similarity

    SciTech Connect (OSTI)

    Omitaomu, Olufemi A

    2014-01-01

    The mining of data streams for online condition monitoring is a challenging task in several domains including (electric) power grid system, intelligent manufacturing, and consumer science. Considering a power grid application in which thousands of sensors, called the phasor measurement units, are deployed on the power grid network to continuously collect streams of digital data for real-time situational awareness and system management. Depending on design, each sensor could stream between ten and sixty data samples per second. The myriad of sensory data captured could convey deeper insights about sequence of events in real-time and before major damages are done. However, the timely processing and analysis of these high-velocity and high-volume data streams is a challenge. Hence, a new data processing and transformation approach, based on the concept of control charts, for representing sequence of data streams from sensors is proposed. In addition, an application of the proposed approach for enhancing data mining tasks such as clustering using real-world power grid data streams is presented. The results indicate that the proposed approach is very efficient for data streams storage and manipulation.

  6. Sustainable development: Background an represent policy views for governmental agencies, industry, and other specialty groups

    SciTech Connect (OSTI)

    Dickerman, J.A.; Silverman, G.S.

    1995-12-01

    Sustainable development is a phrase that has come into common usage without benefit of clear definition or meaning. Usage very much reflects individual and group perspectives: foresters might consider sustainability in terms of maintaining ecological integrity as part of managing forests for wood harvesting, industry might emphasize pollution control, while government agencies may be looking for new ways to exploit resources on a more continuous basis. Perhaps the greatest commonality among groups considering these issues is that {open_quotes}sustainability{close_quotes} has not been attained but that it needs to occur. The National Association of Environmental Professionals (NAEP) agrees that it is critical to the health of the planet that sustainable development be actively pursued and implemented in international, national, regional, and local policies and practices. To contribute to this effort a {open_quotes}white paper{close_quotes} is being prepared. Its purpose is twofold: (1) to review the existing information from the NAEP Sustainable Development Working Group and the literature and through examination of these policies, to clarify the thinking, what is being done, and what is still needed; and (2) to develop a position and action plan. This action plan should direct NAEP`s actions in making a significant contribution to the national dialog. This paper presents the background and results of the review phase of this white paper development. Representative views on sustainable development policy and practice are presented from three perspectives: governmental agencies, industry, and other specialty groups.

  7. Nucleon Electromagnetic Form Factors

    SciTech Connect (OSTI)

    Marc Vanderhaeghen; Charles Perdrisat; Vina Punjabi

    2007-10-01

    There has been much activity in the measurement of the elastic electromagnetic proton and neutron form factors in the last decade, and the quality of the data has greatly improved by performing double polarization experiments, in comparison with previous unpolarized data. Here we review the experimental data base in view of the new results for the proton, and neutron, obtained at JLab, MAMI, and MIT-Bates. The rapid evolution of phenomenological models triggered by these high-precision experiments will be discussed, including the recent progress in the determination of the valence quark generalized parton distributions of the nucleon, as well as the steady rate of improvements made in the lattice QCD calculations.

  8. Representing northern peatland microtopography and hydrology within the Community Land Model

    SciTech Connect (OSTI)

    Shi, X.; Thornton, P. E.; Ricciuto, D. M.; Hanson, P. J.; Mao, J.; Sebestyen, S. D.; Griffiths, N. A.; Bisht, G.

    2015-02-20

    Predictive understanding of northern peatland hydrology is a necessary precursor to understanding the fate of massive carbon stores in these systems under the influence of present and future climate change. Current models have begun to address microtopographic controls on peatland hydrology, but none have included a prognostic calculation of peatland water table depth for a vegetated wetland, independent of prescribed regional water tables. We introduce here a new configuration of the Community Land Model (CLM) which includes a fully prognostic water table calculation for a vegetated peatland. Our structural and process changes to CLM focus on modifications needed to represent the hydrologic cycle of bogs environment with perched water tables, as well as distinct hydrologic dynamics and vegetation communities of the raised hummock and sunken hollow microtopography characteristic of peatland bogs. The modified model was parameterized and independently evaluated against observations from an ombrotrophic raised-dome bog in northern Minnesota (S1-Bog), the site for the Spruce and Peatland Responses Under Climatic and Environmental Change experiment (SPRUCE). Simulated water table levels compared well with site-level observations. The new model predicts significant hydrologic changes in response to planned warming at the SPRUCE site. At present, standing water is commonly observed in bog hollows after large rainfall events during the growing season, but simulations suggest a sharp decrease in water table levels due to increased evapotranspiration under the most extreme warming level, nearly eliminating the occurrence of standing water in the growing season. Simulated soil energy balance was strongly influenced by reduced winter snowpack under warming simulations, with the warming influence on soil temperature partly offset by the loss of insulating snowpack in early and late winter. The new model provides improved predictive capacity for seasonal hydrological dynamics in northern peatlands, and provides a useful foundation for investigation of northern peatland carbon exchange.

  9. Characteristics RSE Column Factor: Total

    U.S. Energy Information Administration (EIA) Indexed Site

    and 1994 Vehicle Characteristics RSE Column Factor: Total 1993 Family Income Below Poverty Line Eli- gible for Fed- eral Assist- ance 1 RSE Row Factor: Less than 5,000 5,000...

  10. Development of a Future Representative Concentration Pathway for Use in the IPCC 5th Assessment Earth System Model Simulations

    SciTech Connect (OSTI)

    None

    2010-12-29

    The representative concentration pathway to be delivered is a scenario of atmospheric concentrations of greenhouse gases and other radiatively important atmospheric species, along with land-use changes, derived from the Global Change Assessment Model (GCAM). The particular representative concentration pathway (RCP) that the Joint Global Change Research Institute (JGCRI) has been responsible for is a not-to-exceed pathway that stabilizes at a radiative forcing of 4.5Wm-2 in the year 2100.

  11. A Hydro-Economic Approach to Representing Water Resources Impacts in Integrated Assessment Models

    SciTech Connect (OSTI)

    Kirshen, Paul H.; Strzepek, Kenneth, M.

    2004-01-14

    Grant Number DE-FG02-98ER62665 Office of Energy Research of the U.S. Department of Energy Abstract Many Integrated Assessment Models (IAM) divide the world into a small number of highly aggregated regions. Non-OECD countries are aggregated geographically into continental and multiple-continental regions or economically by development level. Current research suggests that these large scale aggregations cannot accurately represent potential water resources-related climate change impacts. In addition, IAMs do not explicitly model the flow regulation impacts of reservoir and ground water systems, the economics of water supply, or the demand for water in economic activities. Using the International Model for Policy Analysis of Agricultural Commodities and Trade (IMPACT) model of the International Food Policy Research Institute (IFPRI) as a case study, this research implemented a set of methodologies to provide accurate representation of water resource climate change impacts in Integrated Assessment Models. There were also detailed examinations of key issues related to aggregated modeling including: modeling water consumption versus water withdrawals; ground and surface water interactions; development of reservoir cost curves; modeling of surface areas of aggregated reservoirs for estimating evaporation losses; and evaluating the importance of spatial scale in river basin modeling. The major findings include: - Continental or national or even large scale river basin aggregation of water supplies and demands do not accurately capture the impacts of climate change in the water and agricultural sector in IAMs. - Fortunately, there now exist gridden approaches (0.5 X 0.5 degrees) to model streamflows in a global analysis. The gridded approach to hydrologic modeling allows flexibility in aligning basin boundaries with national boundaries. This combined with GIS tools, high speed computers, and the growing availability of socio-economic gridded data bases allows assignment of demands to river basins to create hydro-economic zones that respect as much as possible both political and hydrologic integrity in different models. - To minimize pre-processing of data and add increased flexibility to modeling water resources and uses, it is recommended that water withdrawal demands be modeled, not consumptive requirements even though this makes the IAM more complex. - IAMs must consider changes in water availability for irrigation under climate change; ignoring them is more inaccurate than ignoring yield changes in crops under climate change. - Determining water availability and cost in river basins must include modeling streamflows, reservoirs and their operations, and ground water and its interaction with surface water. - Scale issues are important. The results from condensing demands and supplies in a large complex river basin to one node can be misleading for all uses under low flow conditions and instream flow uses under all conditions. Monthly is generally the most accurate scale for modeling river flows and demands. Challenges remain in integrating hydrologic units with political boundaries but the gridded approach to hydrologic modeling allows flexibility in aligning basin boundaries with political boundaries. - Using minimal reservoir cost data, it is possible to use basin topography to estimate reservoir storage costs. - Reservoir evaporation must be considered when assessing the usable water in a watershed. Several methods are available to estimate the relationship between aggregated storage surface area and storage volume. - For existing or future IAMs that can not use the appropriate aggregation for water, a water preprocessor may be required due the finer scale of hydrologic impacts.

  12. Using partial safety factors in wind turbine design and testing

    SciTech Connect (OSTI)

    Musial, W.D.; Butterfield, C.

    1997-09-01

    This paper describes the relationship between wind turbine design and testing in terms of the certification process. An overview of the current status of international certification is given along with a description of limit-state design basics. Wind turbine rotor blades are used to illustrate the principles discussed. These concepts are related to both International Electrotechnical Commission and Germanischer Lloyd design standards, and are covered using schematic representations of statistical load and material strength distributions. Wherever possible, interpretations of the partial safety factors are given with descriptions of their intended meaning. Under some circumstances, the authors` interpretations may be subjective. Next, the test-load factors are described in concept and then related to the design factors. Using technical arguments, it is shown that some of the design factors for both load and materials must be used in the test loading, but some should not be used. In addition, some test factors not used in the design may be necessary for an accurate test of the design. The results show that if the design assumptions do not clearly state the effects and uncertainties that are covered by the design`s partial safety factors, outside parties such as test labs or certification agencies could impose their own meaning on these factors.

  13. Selection of powder factor in large diameter blastholes

    SciTech Connect (OSTI)

    Eloranta, J.

    1995-12-31

    This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, The cheapest crushing is done in the pit, appears accurate in this case study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone. Measurable, overall costs decline while shovel and crusher productivity rise by about 5% when powder factor rises by 15%. These trends were previously masked by the effects of: weather, ore grade fluctuations and accounting practices. Attempts to correlate increased powder factor to: wear materials in the crushing plant and to shovel hoist rope life have not shown the same benefit.

  14. Frequency dependence of mass flow gain factor and cavitation compliance of cavitating inducers

    SciTech Connect (OSTI)

    Otsuka, S.; Tsujimoto, Yoshinobu [Osaka Univ. (Japan); Kamijo, Kenjiro [National Aerospace Lab., Kakuda, Miyagi (Japan). Kakuda Research Center; Furuya, O. [AMP Technologies, Osaka (Japan)

    1994-12-31

    Unsteady cavitation characteristics are analyzed based on a closed cavity model in which the length of the cavity is allowed to oscillate. It is shown that the present model blends smoothly into quasisteady calculations in the low frequency limit, unlike fixed cavity length models. Effects of incidence angle and cavitation number on cavitation compliance and mass flow gain factor are shown as functions of reduce frequency. The cavity volume is evaluated by three methods and the results were used to confirm the accuracy and adequacy of the numerical calculation. By comparison with experimental data on inducers, it was shown that the present model can simulate the characteristics of unsteady cavitation qualitatively.

  15. Factor CO2 | Open Energy Information

    Open Energy Info (EERE)

    Factor CO2 Jump to: navigation, search Name: Factor CO2 Place: Bilbao, Spain Zip: 48008 Product: Spain-based consultancy specializing in climate change projects. References: Factor...

  16. An advanced algorithm for construction of Integral Transport Matrix Method operators using accumulation of single cell coupling factors

    SciTech Connect (OSTI)

    Powell, B. P.; Azmy, Y. Y.

    2013-07-01

    The Integral Transport Matrix Method (ITMM) has been shown to be an effective method for solving the neutron transport equation in large domains on massively parallel architectures. In the limit of very large number of processors, the speed of the algorithm, and its suitability for unstructured meshes, i.e. other than an ordered Cartesian grid, is limited by the construction of four matrix operators required for obtaining the solution in each sub-domain. The existing algorithm used for construction of these matrix operators, termed the differential mesh sweep, is computationally expensive and was developed for a structured grid. This work proposes the use of a new algorithm for construction of these operators based on the construction of a single, fundamental matrix representing the transport of a particle along every possible path throughout the sub-domain mesh. Each of the operators is constructed by multiplying an element of this fundamental matrix by two factors dependent only upon the operator being constructed and on properties of the emitting and incident cells. The ITMM matrix operator construction time for the new algorithm is demonstrated to be shorter than the existing algorithm in all tested cases with both isotropic and anisotropic scattering considered. While also being a more efficient algorithm on a structured Cartesian grid, the new algorithm is promising in its geometric robustness and potential for being applied to an unstructured mesh, with the ultimate goal of application to an unstructured tetrahedral mesh on a massively parallel architecture. (authors)

  17. Human Factors Engineering Analysis Tool

    Energy Science and Technology Software Center (OSTI)

    2002-03-04

    HFE-AT is a human factors engineering (HFE) software analysis tool (AT) for human-system interface design of process control systems, and is based primarily on NUREG-0700 guidance.

  18. SECTION M_Evaluation Factors

    National Nuclear Security Administration (NNSA)

    SECTION M EVALUATION FACTORS FOR AWARD TABLE OF CONTENTS M-1 EVALUATION OF PROPOSALS .....................................................................................2 M-2 BASIS FOR CONTRACT AWARD ...................................................................................3 M-3 TECHNICAL AND MANAGEMENT CRITERIA ..........................................................3 M-4 COST CRITERION

  19. Construction Control Representative

    Broader source: Energy.gov [DOE]

    (See Frequently Asked Questions for more information). Where would I be working? Western Area Power Administration Rocky Mountain Region Engineering and Construction Field Engineering, (J5600) 5555...

  20. Reducing Power Factor Cost | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Reducing Power Factor Cost Reducing Power Factor Cost Low power factor is expensive and inefficient. Many utility companies charge an additional fee if your power factor is less than 0.95. Low power factor also reduces your electrical system's distribution capacity by increasing current flow and causing voltage drops. This fact sheet describes power factor and explains how you can improve your power factor to reduce electric bills and enhance your electrical system's capacity. PDF icon Reducing

  1. Human factors in software development

    SciTech Connect (OSTI)

    Curtis, B.

    1986-01-01

    This book presents an overview of ergonomics/human factors in software development, recent research, and classic papers. Articles are drawn from the following areas of psychological research on programming: cognitive ergonomics, cognitive psychology, and psycholinguistics. Topics examined include: theoretical models of how programmers solve technical problems, the characteristics of programming languages, specification formats in behavioral research and psychological aspects of fault diagnosis.

  2. Transcription factor-based biosensor

    DOE Patents [OSTI]

    2013-10-08

    The present invention provides for a system comprising a BmoR transcription factor, a .sigma..sup.54-RNA polymerase, and a pBMO promoter operatively linked to a reporter gene, wherein the pBMO promoter is capable of expression of the reporter gene with an activated form of the BmoR and the .sigma..sup.54-RNA polymerase.

  3. DOE-STD-1063-97; DOE Standard Establishing and Maintaining a Facility Representative Program at DOE Facilities

    Office of Environmental Management (EM)

    3-97 October 1997 Supersedes DOE-STD-1063-93 DOE STANDARD ESTABLISHING AND MAINTAINING A FACILITY REPRESENTATIVE PROGRAM AT DOE FACILITIES U.S. Department of Energy AREA FACR Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced directly from the best available copy. Available to DOE and DOE contractors from the Office of Scientific and Technical Information, P.O. Box 62, Oak Ridge, TN 37831; (423) 576-8401.

  4. IPCC Emission Factor Database | Open Energy Information

    Open Energy Info (EERE)

    Emission Factor Database Jump to: navigation, search Tool Summary LAUNCH TOOL Name: IPCC Emission Factor Database AgencyCompany Organization: World Meteorological Organization,...

  5. Industrial Power Factor Analysis Guidebook. (Technical Report...

    Office of Scientific and Technical Information (OSTI)

    Industrial Power Factor Analysis Guidebook. Citation Details In-Document Search Title: Industrial Power Factor Analysis Guidebook. You are accessing a document from the ...

  6. Factors Impacting Decommissioning Costs - 13576

    SciTech Connect (OSTI)

    Kim, Karen; McGrath, Richard

    2013-07-01

    The Electric Power Research Institute (EPRI) studied United States experience with decommissioning cost estimates and the factors that impact the actual cost of decommissioning projects. This study gathered available estimated and actual decommissioning costs from eight nuclear power plants in the United States to understand the major components of decommissioning costs. Major costs categories for decommissioning a nuclear power plant are removal costs, radioactive waste costs, staffing costs, and other costs. The technical factors that impact the costs were analyzed based on the plants' decommissioning experiences. Detailed cost breakdowns by major projects and other cost categories from actual power plant decommissioning experiences will be presented. Such information will be useful in planning future decommissioning and designing new plants. (authors)

  7. Human factors in waste management

    SciTech Connect (OSTI)

    Moray, N.

    1994-10-01

    This article examines the role of human factors in radioactive waste management. Although few problems and ergonomics are special to radioactive waste management, some problems are unique especially with long term storage. The entire sociotechnical system must be looked at in order to see where improvement can take place because operator errors, as seen in Chernobyl and Bhopal, are ultimately the result of management errors.

  8. Factors Affecting PMU Installation Costs

    Office of Environmental Management (EM)

    September 2014 United States Department of Energy Washington, DC 20585 Department of Energy | September 2014 Factors Affecting PMU Installation Costs | Page ii Acknowledgments This report was sponsored by the U.S. Department of Energy's Office of Electricity Delivery and Energy Reliability (DOE-OE) and drafted by the Oak Ridge National Laboratory (ORNL). The effort was directed and supported by DOE program manager Joseph Paladino. The lead authors are Marcus Young of ORNL and Alison Silverstein

  9. Use of short-term test systems for the prediction of the hazard represented by potential chemical carcinogens

    SciTech Connect (OSTI)

    Glass, L.R.; Jones, T.D.; Easterly, C.E.; Walsh, P.J.

    1990-10-01

    It has been hypothesized that results from short-term bioassays will ultimately provide information that will be useful for human health hazard assessment. Historically, the validity of the short-term tests has been assessed using the framework of the epidemiologic/medical screens. In this context, the results of the carcinogen (long-term) bioassay is generally used as the standard. However, this approach is widely recognized as being biased and, because it employs qualitative data, cannot be used to assist in isolating those compounds which may represent a more significant toxicologic hazard than others. In contrast, the goal of this research is to address the problem of evaluating the utility of the short-term tests for hazard assessment using an alternative method of investigation. Chemicals were selected mostly from the list of carcinogens published by the International Agency for Research on Carcinogens (IARC); a few other chemicals commonly recognized as hazardous were included. Tumorigenicity and mutagenicity data on 52 chemicals were obtained from the Registry of Toxic Effects of Chemical Substances (RTECS) and were analyzed using a relative potency approach. The data were evaluated in a format which allowed for a comparison of the ranking of the mutagenic relative potencies of the compounds (as estimated using short-term data) vs. the ranking of the tumorigenic relative potencies (as estimated from the chronic bioassays). Although this was a preliminary investigation, it offers evidence that the short-term tests systems may be of utility in ranking the hazards represented by chemicals which may contribute to increased carcinogenesis in humans as a result of occupational or environmental exposures. 177 refs., 8 tabs.

  10. Long term out-of-pile thermocouple tests in conditions representative for nuclear gas-cooled high temperature reactors

    SciTech Connect (OSTI)

    Laurie, M.; Fourrez, S.; Fuetterer, M. A.; Lapetite, J. M.

    2011-07-01

    During irradiation tests at high temperature, failure of commercial Inconel 600 sheathed thermocouples is commonly encountered. To understand and remedy this problem, out-of-pile tests were performed with thermocouples in carburizing atmospheres which can be assumed to be at least locally representative for High Temperature Reactors. The objective was to screen those thermocouples which would consecutively be used under irradiation. Two such screening tests have been performed with a set of thermocouples embedded in graphite (mainly conventional Type N thermocouples and thermocouples with innovative sheaths) in a dedicated furnace with helium flushing. Performance indicators such as thermal drift, insulation and loop resistance were monitored and compared to those from conventional Type N thermocouples. Several parameters were investigated: niobium sleeves, bending, thickness, sheath composition, temperature as well as the chemical environment. After the tests, Scanning Electron Microscopy (SEM) examinations were performed to analyze possible local damage in wires and in the sheath. The present paper describes the two experiments, summarizes results and outlines further work, in particular to further analyze the findings and to select suitable thermocouples for qualification under irradiation. (authors)

  11. THE SPITZER EXTRAGALACTIC REPRESENTATIVE VOLUME SURVEY: THE ENVIRONMENTS OF HIGH-z SDSS QUASI-STELLAR OBJECTS

    SciTech Connect (OSTI)

    Falder, J. T.; Stevens, J. A.; Jarvis, Matt J.; Bonfield, D. G.; Lacy, M.; Farrah, D.; Oliver, S.; Surace, J.; Mauduit, J.-C.; Gonzalez-Solares, E.; Afonso, J.; Cava, A.; Seymour, N.

    2011-07-10

    This paper presents a study of the environments of SDSS quasi-stellar objects (QSOs) in the Spitzer Extragalactic Representative Volume Survey (SERVS). We concentrate on the high-redshift QSOs as these have not been studied in large numbers with data of this depth before. We use the IRAC 3.6-4.5 {mu}m color of objects and ancillary r-band data to filter out as much foreground contamination as possible. This technique allows us to find a significant (>4{sigma}) overdensity of galaxies around QSOs in a redshift bin centered on z {approx} 2.0 and an (>2{sigma}) overdensity of galaxies around QSOs in a redshift bin centered on z {approx} 3.3. We compare our findings to the predictions of a semi-analytic galaxy formation model, based on the {Lambda}CDM MILLENNIUM simulation, and find for both redshift bins that the model predictions match well the source density we have measured from the SERVS data.

  12. Genome analysis of Elusimicrobium minutum, the first cultivated representative of the Elusimicrobia phylum (formerly Termite Group 1)

    SciTech Connect (OSTI)

    Herlemann, D. P. R.; Geissinger, O.; Ikeda-Ohtsubo, W.; Kunin, V.; Sun, H.; Lapidus, A.; Hugenholtz, P.; Brune, A.

    2009-02-01

    The candidate phylum Termite group 1 (TG1), is regularly 1 encountered in termite hindguts but is present also in many other habitats. Here we report the complete genome sequence (1.64 Mbp) of Elusimicrobium minutum strain Pei191{sup T}, the first cultured representative of the TG1 phylum. We reconstructed the metabolism of this strictly anaerobic bacterium isolated from a beetle larva gut and discuss the findings in light of physiological data. E. minutum has all genes required for uptake and fermentation of sugars via the Embden-Meyerhof pathway, including several hydrogenases, and an unusual peptide degradation pathway comprising transamination reactions and leading to the formation of alanine, which is excreted in substantial amounts. The presence of genes encoding lipopolysaccharide biosynthesis and the presence of a pathway for peptidoglycan formation are consistent with ultrastructural evidence of a Gram-negative cell envelope. Even though electron micrographs showed no cell appendages, the genome encodes many genes putatively involved in pilus assembly. We assigned some to a type II secretion system, but the function of 60 pilE-like genes remains unknown. Numerous genes with hypothetical functions, e.g., polyketide synthesis, non-ribosomal peptide synthesis, antibiotic transport, and oxygen stress protection, indicate the presence of hitherto undiscovered physiological traits. Comparative analysis of 22 concatenated single-copy marker genes corroborated the status of Elusimicrobia (formerly TG1) as a separate phylum in the bacterial domain, which was so far based only on 16S rRNA sequence analysis.

  13. The Impact of Emission and Climate Change on Ozone in the United States under Representative Concentration Pathways (RCPs)

    SciTech Connect (OSTI)

    Gao, Yang; Fu, Joshua S.; Drake, John B.; Lamarque, J.-F.; Liu, Yang

    2013-09-27

    Dynamical downscaling was applied in this study to link the global climate-chemistry model Community Atmosphere Model (CAM-Chem) with the regional models: Weather Research and Forecasting (WRF) Model and Community Multi-scale Air Quality (CMAQ). Two Representative Concentration Pathway (RCP) scenarios (RCP 4.5 and RCP 8.5) were used to evaluate the climate impact on ozone concentrations in 2050s. Ozone concentrations in the lower-mid troposphere (surface to ~300 hPa), from mid- to high latitudes in the Northern Hemisphere (NH), show decreasing trends in RCP 4.5 between 2000s and 2050s, with the largest decrease of 4-10 ppbv occurring in the summer and the fall; and increasing trends (2-12 ppbv) in RCP 8.5 resulting from the increased methane emissions. In RCP 8.5, methane emissions increase by ~60% by the end of 2050s, accounting for more than 90% of ozone increases in summer and fall, and 60-80% in spring and winter. Under the RCP 4.5 scenario, in the summer when photochemical reactions are the most active, the large ozone precursor emissions reduction leads to the greatest decrease of downscaled surface ozone concentrations, ranging from 6 to 10 ppbv. However, a few major cities show ozone increases of 3 to 7 ppbv due to weakened NO titration. Under the RCP 8.5 scenario, in winter, downscaled ozone concentrations increase across nearly the entire continental US in winter, ranging from 3 to 10 ppbv due to increased methane emissions and enhanced stratosphere-troposphere exchange (STE). More intense heat waves are projected to occur by the end of 2050s in RCP 8.5, leading to more than 8 ppbv of the maximum daily 8-hour daily average (MDA8) ozone during the heat wave days than other days; this indicates the dramatic impact heat waves exert on high frequency ozone events.

  14. Cone Penetrometer N Factor Determination Testing Results

    SciTech Connect (OSTI)

    Follett, Jordan R.

    2014-03-05

    This document contains the results of testing activities to determine the empirical 'N Factor' for the cone penetrometer in kaolin clay simulant. The N Factor is used to releate resistance measurements taken with the cone penetrometer to shear strength.

  15. Clothes Washer Test Cloth Correction Factor Information

    Broader source: Energy.gov [DOE]

    This page contains the information used to determine the test cloth correction factors for each test cloth lot.

  16. Factorization method and new potentials from the inverted oscillator

    SciTech Connect (OSTI)

    Bermudez, David Fernández C, David J.

    2013-06-15

    In this article we will apply the first- and second-order supersymmetric quantum mechanics to obtain new exactly-solvable real potentials departing from the inverted oscillator potential. This system has some special properties; in particular, only very specific second-order transformations produce non-singular real potentials. It will be shown that these transformations turn out to be the so-called complex ones. Moreover, we will study the factorization method applied to the inverted oscillator and the algebraic structure of the new Hamiltonians. -- Highlights: •We apply supersymmetric quantum mechanics to the inverted oscillator potential. •The complex second-order transformations allow us to build new non-singular potentials. •The algebraic structure of the initial and final potentials is analyzed. •The initial potential is described by a complex-deformed Heisenberg–Weyl algebra. •The final potentials are described by polynomial Heisenberg algebras.

  17. Human factors: a necessary tool for industry

    SciTech Connect (OSTI)

    Starcher, K.O.

    1984-03-09

    The need for human factors (ergonomics) input in the layout of a ferroelectric ceramics laboratory is presented as an example of the overall need for human factors professionals in industry. However, even in the absence of one trained in human factors, knowledge of a few principles in ergonomics will provide many possibilities for improving performance in the industrial environment.

  18. Antenna factorization in strongly ordered limits

    SciTech Connect (OSTI)

    Kosower, David A.

    2005-02-15

    When energies or angles of gluons emitted in a gauge-theory process are small and strongly ordered, the emission factorizes in a simple way to all orders in perturbation theory. I show how to unify the various strongly ordered soft, mixed soft-collinear, and collinear limits using antenna factorization amplitudes, which are generalizations of the Catani-Seymour dipole factorization function.

  19. Ultrastructural Study on Ultra-Low Frequency Electromagnetic Fields and Transfer Factor Effects on Skin Ulcers

    SciTech Connect (OSTI)

    Cadena, M. S. Reyes; Chapul, L. Sanchez; Perez, Javier; Garcia, M. N. Jimenez; Lopez, M. A. Jimenez; Espindola, M. E. Sanchez; Perez, R. Paniagua; Hernandez, N. A.; Paniagua, G.; Uribe, F.; Nava, J. J. Godina; Segura, M. A. Rodriguez

    2008-08-11

    We determined the effect of 120Hz ultra low frequency electromagnetic field (ELF) on the healing process of skin in 20 Wistar rats distributed in four groups in which chronic dermal ulcers had been produced. The first two groups received a dose of the transfer factor and interferon-beta (IFN-{beta}) every 24 h during 12 days. The third group (positive control) received only electromagnetic field (ELF) sessions, and in the fourth group (negative control), no treatment was applied. The electromagnetic field was applied through a Helmholtz coils; 30 Gauss of intensity. Results shown histological changes that improve the healing process in animals subjected to ELF together with the transfer factor.

  20. Factors fragmenting the Russian Federation

    SciTech Connect (OSTI)

    Brown, E.

    1993-10-06

    This paper examines the factors that threaten the future of the Russian Federation (RF). The observations are based on a study that focused on eight republics: Mordova, Udmurtia, Tatarstan, Mari El, Bashkortostan, Kabardino-Balkaria, Buryatia, and Altay Republic. These republics were selected for their geographic and economic significance to the RF. Tatarstan, Bashkortostan, Udmurtia, and Mari El are located on important supply routes, such as the Volga River and the trans-Siberian railroad. Some of these republics are relatively wealthy, with natural resources such as oil (e.g., Tatarstan and Bashkortostan), and all eight republics play significant roles in the military-industrial complex. The importance of these republics to the RF contrasts to the relative insignificance of the independence-minded Northern Caucasus area. The author chose not to examine the Northern Caucasus region (except Kabardino-Balkaria) because these republics may have only a minor impact on the rest of the RF if they secede. Their impact would be minimized because they lie on the frontiers of the RF. Many Russians believe that {open_quotes}it might be best to let such a troublesome area secede.{close_quotes}

  1. Dense LU Factorization on Multicore Supercomputer Nodes (Conference...

    Office of Scientific and Technical Information (OSTI)

    DIMENSIONS; DISTRIBUTION; FACTORIZATION; IMPLEMENTATION; PERFORMANCE; PROCESSING; ROTATION; SUPERCOMPUTERS dense LU factorization; mapping; numerical algorithms; linear algebra...

  2. Synthetic heparin-binding growth factor analogs

    DOE Patents [OSTI]

    Pena, Louis A.; Zamora, Paul; Lin, Xinhua; Glass, John D.

    2007-01-23

    The invention provides synthetic heparin-binding growth factor analogs having at least one peptide chain that binds a heparin-binding growth factor receptor, covalently bound to a hydrophobic linker, which is in turn covalently bound to a non-signaling peptide that includes a heparin-binding domain. The synthetic heparin-binding growth factor analogs are useful as soluble biologics or as surface coatings for medical devices.

  3. Industrial Power Factor Analysis Guidebook. Electrotek Concepts...

    Office of Scientific and Technical Information (OSTI)

    low power factors, increased conductor and transformer losses, and lower voltages. Utilities must supply both active and reactive power and compensate for these losses. Power...

  4. Summary - Major Risk Factors Integrated Facility Disposition...

    Office of Environmental Management (EM)

    Office of Environmental Management (DOE-EM) External Technical Review of the Major Risk Factors Integrated Facility Disposition Project (IFDP) Oak Ridge, TN Why DOE-EM Did...

  5. EcoFactor Inc | Open Energy Information

    Open Energy Info (EERE)

    Name: EcoFactor Inc Place: Millbrae, California Zip: 94030 Product: California-based home energy management service provider. Coordinates: 37.60276, -122.395444 Show Map...

  6. CONTROL OF MECHANICALLY ACTIVATED POLYMERSOME FUSION: FACTORS...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Journal Article: CONTROL OF MECHANICALLY ACTIVATED POLYMERSOME FUSION: FACTORS AFFECTING FUSION. Citation Details In-Document Search Title: CONTROL OF MECHANICALLY ACTIVATED...

  7. CONTROL OF MECHANICALLY ACTIVATED POLYMERSOME FUSION: FACTORS...

    Office of Scientific and Technical Information (OSTI)

    MECHANICALLY ACTIVATED POLYMERSOME FUSION: FACTORS AFFECTING FUSION. Henderson, Ian M.; Paxton, Walter F Abstract not provided. Sandia National Laboratories (SNL-NM), Albuquerque,...

  8. Emission Factors (EMFAC) | Open Energy Information

    Open Energy Info (EERE)

    The EMission FACtors (EMFAC) model is used to calculate emission rates from all motor vehicles, such as passenger cars to heavy-duty trucks, operating on highways, freeways...

  9. Preparation and characterization of cobalt-substituted anthrax lethal factor

    SciTech Connect (OSTI)

    Saebel, Crystal E.; Carbone, Ryan; Dabous, John R.; Lo, Suet Y. [Department of Chemistry and Biochemistry, Laurentian University, 935 Ramsey Lake Rd., Sudbury, Ontario, Canada P3E 2C6 (Canada)] [Department of Chemistry and Biochemistry, Laurentian University, 935 Ramsey Lake Rd., Sudbury, Ontario, Canada P3E 2C6 (Canada); Siemann, Stefan, E-mail: ssiemann@laurentian.ca [Department of Chemistry and Biochemistry, Laurentian University, 935 Ramsey Lake Rd., Sudbury, Ontario, Canada P3E 2C6 (Canada)] [Department of Chemistry and Biochemistry, Laurentian University, 935 Ramsey Lake Rd., Sudbury, Ontario, Canada P3E 2C6 (Canada)

    2011-12-09

    Highlights: Black-Right-Pointing-Pointer Cobalt-substituted anthrax lethal factor (CoLF) is highly active. Black-Right-Pointing-Pointer CoLF can be prepared by bio-assimilation and direct exchange. Black-Right-Pointing-Pointer Lethal factor binds cobalt tightly. Black-Right-Pointing-Pointer The electronic spectrum of CoLF reveals penta-coordination. Black-Right-Pointing-Pointer Interaction of CoLF with thioglycolic acid follows a 2-step mechanism. -- Abstract: Anthrax lethal factor (LF) is a zinc-dependent endopeptidase involved in the cleavage of mitogen-activated protein kinase kinases near their N-termini. The current report concerns the preparation of cobalt-substituted LF (CoLF) and its characterization by electronic spectroscopy. Two strategies to produce CoLF were explored, including (i) a bio-assimilation approach involving the cultivation of LF-expressing Bacillus megaterium cells in the presence of CoCl{sub 2}, and (ii) direct exchange by treatment of zinc-LF with CoCl{sub 2}. Independent of the method employed, the protein was found to contain one Co{sup 2+} per LF molecule, and was shown to be twice as active as its native zinc counterpart. The electronic spectrum of CoLF suggests the Co{sup 2+} ion to be five-coordinate, an observation similar to that reported for other Co{sup 2+}-substituted gluzincins, but distinct from that documented for the crystal structure of native LF. Furthermore, spectroscopic studies following the exposure of CoLF to thioglycolic acid (TGA) revealed a sequential mechanism of metal removal from LF, which likely involves the formation of an enzyme: Co{sup 2+}:TGA ternary complex prior to demetallation of the active site. CoLF reported herein constitutes the first spectroscopic probe of LF's active site, which may be utilized in future studies to gain further insight into the enzyme's mechanism and inhibitor interactions.

  10. Experimental study of the relationship between formation factor, porosity, and cementation

    SciTech Connect (OSTI)

    Harig, M.D.; Chaney, R.C.

    1999-07-01

    Cemented granular soils are classified based on the size and distribution of the individual grains and qualitatively on the basis of cementation. To uniquely classify these types of soils, information about the fabric (pore geometry and/or level of cementation) of the specimen needs to be quantified. Electrical resistivity, or its reciprocal, conductivity, methods have been extensively used both in situ and in the laboratory to provide a means for determining a variety of soil index, structural, erosional, and cyclic properties. The objective of this study was to determine the relationship between formation factor (F), porosity (n), and cementation factor (m) of remolded sand-cement specimens. This relationship is shown to provide a mechanism for estimating the level of cementation in undisturbed specimens. The formation factor is the ratio of the electrical resistivity of the sand-water-cement mixture to that of the interstitial water.

  11. Building-related risk factors and work-related lower respiratory symptoms in 80 office buildings

    SciTech Connect (OSTI)

    Mendell, M.J.; Naco, G.M.; Wilcox, T.G.; Sieber, W.K.

    2002-01-01

    We assessed building-related risk factors for lower respiratory symptoms in office workers. The National Institute for Occupational Safety and Health in 1993 collected data during indoor environmental health investigations of workplaces. We used multivariate logistic regression analyses to assess relationships between lower respiratory symptoms in office workers and risk factors plausibly related to microbiologic contamination. Among 2,435 occupants in 80 office buildings, frequent, work-related multiple lower respiratory symptoms were strongly associated, in multivariate models, with two risk factors for microbiologic contamination: poor pan drainage under cooling coils and debris in outside air intake. Associations tended to be stronger among those with a history of physician-diagnosed asthma. These findings suggest that adverse lower respiratory health effects from indoor work environments, although unusual, may occur in relation to poorly designed or maintained ventilation systems, particularly among previously diagnosed asthmatics. These findings require confirmation in more representative buildings.

  12. Gauss Sum Factorization with Cold Atoms

    SciTech Connect (OSTI)

    Gilowski, M.; Wendrich, T.; Mueller, T.; Ertmer, W.; Rasel, E. M. [Institut fuer Quantenoptik, Leibniz Universitaet Hannover, Welfengarten 1, D-30167 Hannover (Germany); Jentsch, Ch. [Astrium GmbH-Satellites, 88039 Friedrichshafen (Germany); Schleich, W. P. [Institut fuer Quantenphysik, Universitaet Ulm, Albert-Einstein-Allee 11, D-89081 Ulm (Germany)

    2008-01-25

    We report the first implementation of a Gauss sum factorization algorithm by an internal state Ramsey interferometer using cold atoms. A sequence of appropriately designed light pulses interacts with an ensemble of cold rubidium atoms. The final population in the involved atomic levels determines a Gauss sum. With this technique we factor the number N=263193.

  13. Section M: Evaluations Factors for Award

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    V SECTION M EVALUATION FACTORS FOR AWARD Request for Proposal # DE-RP36-07GO97036 PART V SECTION M EVALUATION FACTORS FOR AWARD TABLE OF CONTENTS M.1 Evaluation of Proposals ..........................................................................................1 M.2 Evaluation Criteria..................................................................................................1 M.3 Basis For Award

  14. Two-Factor Authentication | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Authentication Two-Factor Authentication computer-767784_960_720.jpg Two-Factor Authentication (2FA) (also known as 2-Step Verification) is a system that employs two methods to identify an individual. More secure than reusable passwords, when a token's random number is combined with a secret PIN, the resulting passcode provides positive identification, and more reliable user authentication.

  15. Synthetic heparin-binding factor analogs

    DOE Patents [OSTI]

    Pena, Louis A.; Zamora, Paul O.; Lin, Xinhua; Glass, John D.

    2010-04-20

    The invention provides synthetic heparin-binding growth factor analogs having at least one peptide chain, and preferably two peptide chains branched from a dipeptide branch moiety composed of two trifunctional amino acid residues, which peptide chain or chains bind a heparin-binding growth factor receptor and are covalently bound to a non-signaling peptide that includes a heparin-binding domain, preferably by a linker, which may be a hydrophobic linker. The synthetic heparin-binding growth factor analogs are useful as pharmaceutical agents, soluble biologics or as surface coatings for medical devices.

  16. Two-Factor Identify Proofing Process | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Identify Proofing Process Two-Factor Identify Proofing Process

  17. Residential Energy-Efficiency Equipment Shown to be a Good Investment for U.S. Navy (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2014-04-01

    A two-year project between the National Renewable Energy Laboratory (NREL) and the U.S. Navy's Naval Facilities Engineering Command (NAVFAC) to demonstrate energy efficiency technologies at bases in Hawaii and Guam resulted in the identification of several promising options for reducing energy use and costs, including whole-house energy efficiency retrofits.

  18. Carbon Dioxide Emission Factors for Coal

    Reports and Publications (EIA)

    1994-01-01

    The Energy Information Administration (EIA) has developed factors for estimating the amount of carbon dioxide emitted, accounting for differences among coals, to reflect the changing "mix" of coal in U.S. coal consumption.

  19. Relativistic Thomson Scatter from Factor Calculation

    Energy Science and Technology Software Center (OSTI)

    2009-11-01

    The purpose of this program is calculate the fully relativistic Thomson scatter from factor in unmagnetized plasmas. Such calculations are compared to experimental diagnoses of plasmas at such facilities as the Jupiter laser facility here a LLNL.

  20. Proton form factor effects in hydrogenic atoms

    SciTech Connect (OSTI)

    Daza, F. Garcia; Kelkar, N. G.; Nowakowski, M.

    2011-10-21

    The proton structure corrections to the hyperfine splittings in electronic and muonic hydrogen are evaluated using the Breit potential with electromagnetic form factors. In contrast to other methods, the Breit equation with q{sup 2} dependent form factors is just an extension of the standard Breit equation which gives the hyperfine splitting Hamiltonian. Precise QED corrections are comparable to the structure corrections which therefore need to be evaluated ab initio.

  1. Comparison of AB2588 multipathway risk factors for California fossil-fuel power stations

    SciTech Connect (OSTI)

    Gratt, L.B.; Levin, L.

    1997-12-31

    Substances released from power plants may travel through various exposure pathways resulting in human health and environmental risks. The stack air emission`s primary pathway is inhalation from the ambient air. Multipathway factors (adjustment factors to the inhalation risk) are used to evaluate the importance of non-inhalation pathways (such as ingestion and dermal contact). The multipathway factor for a specific substance is the health risk by all pathways divided by the inhalation health risk for that substance. These factors are compared for fossil fuel power stations that submitted regulatory risk assessments in compliance with California Toxic Hot Spots Act (AB2588). Substances representing the largest contributions to the cancer risk are of primary concern: arsenic, beryllium, cadmium, chromium (+6), formaldehyde, nickel, lead, selenium, and PAHs. Comparisons of the chemical-specific multipathway factors show the impacts of regulatory policy decisions on the estimated health risk for trace substances. As an example, point estimates of the soil mixing depth, varying from 1 cm to 15 cm, relate to the relative importance of the pathway. For the deeper mixing depths, the root-zone uptake by homegrown tomato plants (for assumed consumption rate of 15% for San Diego) may result in high multipathway factors for several trace metals. For shallower mixing depths, soil ingestion may become the dominant non-inhalation pathway. These differences may lead to significantly different risk estimates for similar facilities located at different California locations such as to be under local regulatory authorities. The overall multipathway factor for the total cancer risk is about 2, much smaller than some of the chemical-specific factors. Science-based multipathway analysis should reduce much of the concern that may be due to policy-based decisions on pathway selection and high-value point-estimates of the parameters.

  2. UESC Training for Utility Representatives

    Broader source: Energy.gov [DOE]

    Webinar covers utility energy service contracts (UESC), which allow utilities to provide their Federal agencies with comprehensive energy and water efficiency improvements and demand-reduction services.

  3. FAQS Qualification Card – Facility Representative

    Broader source: Energy.gov [DOE]

    A key element for the Department’s Technical Qualification Programs is a set of common Functional Area Qualification Standards (FAQS) and associated Job Task Analyses (JTA). These standards are developed for various functional areas of responsibility in the Department, including oversight of safety management programs identified as hazard controls in Documented Safety Analyses (DSA).

  4. PSCAD Modules Representing PV Generator

    SciTech Connect (OSTI)

    Muljadi, E.; Singh, M.; Gevorgian, V.

    2013-08-01

    Photovoltaic power plants (PVPs) have been growing in size, and the installation time is very short. With the cost of photovoltaic (PV) panels dropping in recent years, it can be predicted that in the next 10 years the contribution of PVPs to the total number of renewable energy power plants will grow significantly. In this project, the National Renewable Energy Laboratory (NREL) developed a dynamic modeling of the modules to be used as building blocks to develop simulation models of single PV arrays, expanded to include Maximum Power Point Tracker (MPPT), expanded to include PV inverter, or expanded to cover an entire PVP. The focus of the investigation and complexity of the simulation determines the components that must be included in the simulation. The development of the PV inverter was covered in detail, including the control diagrams. Both the current-regulated voltage source inverter and the current-regulated current source inverter were developed in PSCAD. Various operations of the PV inverters were simulated under normal and abnormal conditions. Symmetrical and unsymmetrical faults were simulated, presented, and discussed. Both the three-phase analysis and the symmetrical component analysis were included to clarify the understanding of unsymmetrical faults. The dynamic model validation was based on the testing data provided by SCE. Testing was conducted at SCE with the focus on the grid interface behavior of the PV inverter under different faults and disturbances. The dynamic model validation covers both the symmetrical and unsymmetrical faults.

  5. Program Analyst (Contracting Officer Representative)

    Broader source: Energy.gov [DOE]

    This position reports directly to the Office Director for PBPE. The incumbent of this position analyzes, evaluates and/or advises management on the effectiveness of complex and overarching EIA...

  6. On Boolean matrices with full factor rank

    SciTech Connect (OSTI)

    Shitov, Ya

    2013-11-30

    It is demonstrated that every (0,1)-matrix of size n×m having Boolean rank n contains a column with at least ?n/2?1 zero entries. This bound is shown to be asymptotically optimal. As a corollary, it is established that the size of a full-rank Boolean matrix is bounded from above by a function of its tropical and determinantal ranks. Bibliography: 16 titles.

  7. Greater-than-Class C low-level radioactive waste characterization. Appendix E-4: Packaging factors for greater-than-Class C low-level radioactive waste

    SciTech Connect (OSTI)

    Quinn, G.; Grant, P.; Winberg, M.; Williams, K.

    1994-09-01

    This report estimates packaging factors for several waste types that are potential greater-than-Class C (GTCC) low-level radioactive waste (LLW). The packaging factor is defined as the volume of a GTCC LLW disposal container divided by the as-generated or ``unpackaged`` volume of the waste loaded into the disposal container. Packaging factors reflect any processes that reduce or increase an original unpackaged volume of GTCC LLW, the volume inside a waste container not occupied by the waste, and the volume of the waste container itself. Three values are developed that represent (a) the base case or most likely value for a packaging factor, (b) a high case packaging factor that corresponds to the largest anticipated disposal volume of waste, and (c) a low case packaging factor for the smallest volume expected. GTCC LLW is placed in three categories for evaluation in this report: activated metals, sealed sources, and all other waste.

  8. Communication-avoiding symmetric-indefinite factorization

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ballard, Grey Malone; Becker, Dulcenia; Demmel, James; Dongarra, Jack; Druinsky, Alex; Peled, Inon; Schwartz, Oded; Toledo, Sivan; Yamazaki, Ichitaro

    2014-11-13

    We describe and analyze a novel symmetric triangular factorization algorithm. The algorithm is essentially a block version of Aasen's triangular tridiagonalization. It factors a dense symmetric matrix A as the product A=PLTLTPT where P is a permutation matrix, L is lower triangular, and T is block tridiagonal and banded. The algorithm is the first symmetric-indefinite communication-avoiding factorization: it performs an asymptotically optimal amount of communication in a two-level memory hierarchy for almost any cache-line size. Adaptations of the algorithm to parallel computers are likely to be communication efficient as well; one such adaptation has been recently published. As a result,more » the current paper describes the algorithm, proves that it is numerically stable, and proves that it is communication optimal.« less

  9. Hadronic form factors in kaon photoproduction

    SciTech Connect (OSTI)

    Syukurilla, L. Mart, T.

    2014-09-25

    We have revisited the effect of hadronic form factors in kaon photoproduction process by utilizing an isobaric model developed for kaon photoproduction off the proton. The model is able to reproduce the available experimental data nicely as well as to reveal the origin of the second peak in the total cross section, which was the main source of confusion for decades. Different from our previous study, in the present work we explore the possibility of using different hadronic form factors in each of the K?N vertices. The use of different hadronic form factors, e.g. dipole, Gaussian, and generalized dipole, has been found to produce a more flexible isobar model, which can provide a significant improvement in the model.

  10. Human factors in nuclear technology - a history

    SciTech Connect (OSTI)

    Jones, D.B. )

    1992-01-01

    Human factors, human factors engineering (HFE), or ergonomics did not receive much formal attention in nuclear technology prior to the Three Mile Island Unit 2 (TMI-2) incident. Three principal reasons exist for this lack of concern. First, emerging technologies show little concern with how people will use a new system. Making the new technology work is considered more important than the people who will use it. Second, the culture of the users of nuclear power did not recognize a need for human factors. Traditional utilities had well established and effective engineering designs for control of electric power generation, while medicine considered the use of nuclear isotopes another useful tool, not requiring special ergonomics. Finally, the nuclear industry owed much to Admiral Rickover. He was definitely opposed.

  11. Chiral extrapolation of nucleon magnetic form factors

    SciTech Connect (OSTI)

    P. Wang; D. Leinweber; A. W. Thomas; R.Young

    2007-04-01

    The extrapolation of nucleon magnetic form factors calculated within lattice QCD is investigated within a framework based upon heavy baryon chiral effective-field theory. All one-loop graphs are considered at arbitrary momentum transfer and all octet and decuplet baryons are included in the intermediate states. Finite range regularization is applied to improve the convergence in the quark-mass expansion. At each value of the momentum transfer (Q{sup 2}), a separate extrapolation to the physical pion mass is carried out as a function of m{sub {pi}} alone. Because of the large values of Q{sup 2} involved, the role of the pion form factor in the standard pion-loop integrals is also investigated. The resulting values of the form factors at the physical pion mass are compared with experimental data as a function of Q{sup 2} and demonstrate the utility and accuracy of the chiral extrapolation methods presented herein.

  12. Communication-avoiding symmetric-indefinite factorization

    SciTech Connect (OSTI)

    Ballard, Grey Malone; Becker, Dulcenia; Demmel, James; Dongarra, Jack; Druinsky, Alex; Peled, Inon; Schwartz, Oded; Toledo, Sivan; Yamazaki, Ichitaro

    2014-11-13

    We describe and analyze a novel symmetric triangular factorization algorithm. The algorithm is essentially a block version of Aasen's triangular tridiagonalization. It factors a dense symmetric matrix A as the product A=PLTLTPT where P is a permutation matrix, L is lower triangular, and T is block tridiagonal and banded. The algorithm is the first symmetric-indefinite communication-avoiding factorization: it performs an asymptotically optimal amount of communication in a two-level memory hierarchy for almost any cache-line size. Adaptations of the algorithm to parallel computers are likely to be communication efficient as well; one such adaptation has been recently published. As a result, the current paper describes the algorithm, proves that it is numerically stable, and proves that it is communication optimal.

  13. Human factors challenges for advanced process control

    SciTech Connect (OSTI)

    Stubler, W.F.; O`Hara, J..M.

    1996-08-01

    New human-system interface technologies provide opportunities for improving operator and plant performance. However, if these technologies are not properly implemented, they may introduce new challenges to performance and safety. This paper reports the results from a survey of human factors considerations that arise in the implementation of advanced human-system interface technologies in process control and other complex systems. General trends were identified for several areas based on a review of technical literature and a combination of interviews and site visits with process control organizations. Human factors considerations are discussed for two of these areas, automation and controls.

  14. Annotated bibliography of human factors applications literature

    SciTech Connect (OSTI)

    McCafferty, D.B.

    1984-09-30

    This bibliography was prepared as part of the Human Factors Technology Project, FY 1984, sponsored by the Office of Nuclear Safety, US Department of Energy. The project was conducted by Lawrence Livermore National Laboratory, with Essex Corporation as a subcontractor. The material presented here is a revision and expansion of the bibliographic material developed in FY 1982 as part of a previous Human Factors Technology Project. The previous bibliography was published September 30, 1982, as Attachment 1 to the FY 1982 Project Status Report.

  15. Heat Transfer and Friction-Factor Methods Turbulent Flow Inside Pipes 3d Rough

    Energy Science and Technology Software Center (OSTI)

    1994-01-21

    Three-dimensional roughened internally enhanced tubes have been shown to be one of the most energy efficient for turbulent, forced convection applications. However, there is only one prediction method presented in the open literature and that is restricted to three-dimensional sand-grain roughness. Other roughness types are being proposed: hemispherical sectors, truncated cones, and full and truncated pyramids. There are no validated heat-transfer and friction-factor prediction methods for these different roughness shapes that can be used inmore » the transition and fully rough region. This program calculates the Nusselt number and friction factor values, for a broad range of three-dimensional roughness types such as hemispherical sectors, truncated cones, and full and truncated pyramids. Users of this program are heat-exchangers designers, enhanced tubing suppliers, and research organizations or academia who are developing or validating prediction methods.« less

  16. High-precision calculation of the strange nucleon electromagnetic form factors

    SciTech Connect (OSTI)

    Green, Jeremy; Meinel, Stefan; Engelhardt, Michael G.; Krieg, Stefan; Laeuchli, Jesse; Negele, John W.; Orginos, Kostas; Pochinsky, Andrew; Syritsyn, Sergey

    2015-08-01

    We report a direct lattice QCD calculation of the strange nucleon electromagnetic form factors GsE and GsM in the kinematic range 0 lte Q2 \\lessapprox 1.2GeV2. For the first time, both GsE and GsM are shown to be nonzero with high significance. This work uses closer-to-physical lattice parameters than previous calculations, and achieves an unprecented statistical precision by implementing a recently proposed variance reduction technique called hierarchical probing. We perform model-independent fits of the form factor shapes using the z-expansion and determine the strange electric and magnetic radii and magnetic moment. We compare our results to parity-violating electron-proton scattering data and to other theoretical studies.

  17. Emission factors for leaks in refinery components in heavy liquid service

    SciTech Connect (OSTI)

    Taback, H.; Godec, M.

    1996-12-31

    The objective of this program was to provide sufficient screening data so that EPA can develop an official set of emission factors (expressed in lb/hr/component) for refinery components (valves, flanged connectors, non-flanged connectors, pumps, open-ended lines, and other) in heavy liquid (BL) service. To accomplish this, 211,000 existing HL screening values from Southern California refineries were compiled and compared with 2,500 new HL screening measurements taken at two refineries in the state of Washington. Since Southern California is an area in extreme non-attainment of the National Ambient Air Quality Standards (NAAQS) and therefore has tight emission control regulations, it was felt that its screening data may not be representative of refineries without tight emission controls. Thus, the Southern California screening data were compared to screening measurements at refineries in an area that is in attainment of the NAAQS and without emissions control, which is the case for those refineries in Washington. It was found that statistically there was no significant difference in emission factors between the two areas and, therefore, there appears to be no difference in emissions from heavy liquid components in areas with and without leak detection and repair (LDAR) programs. The new emission factors range from 1/7 to 1/3 times the current EPA emission factors. This program was sponsored by the American Petroleum Institute (API) and an API report will soon be released providing complete details.

  18. Test of factorization in diffractive deep inelastic scattering...

    Office of Scientific and Technical Information (OSTI)

    Test of factorization in diffractive deep inelastic scattering and photoproduction at HERA Citation Details In-Document Search Title: Test of factorization in diffractive deep ...

  19. Research on Factors Relating to Density and Climate Change |...

    Open Energy Info (EERE)

    on Factors Relating to Density and Climate Change Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Research on Factors Relating to Density and Climate Change Agency...

  20. First Climate formerly Factor Consulting | Open Energy Information

    Open Energy Info (EERE)

    First Climate formerly Factor Consulting Jump to: navigation, search Name: First Climate (formerly Factor Consulting) Place: Germany Sector: Carbon Product: Former Swiss-based...

  1. Module: Emission Factors for Deforestation | Open Energy Information

    Open Energy Info (EERE)

    www.leafasia.orgtoolstechnical-guidance-series-emission-factors-defo Cost: Free Language: English Module: Emission Factors for Deforestation Screenshot Logo: Module: Emission...

  2. HUMAN FACTORS GUIDANCE FOR CONTROL ROOM EVALUATION

    SciTech Connect (OSTI)

    OHARA,J.; BROWN,W.; STUBLER,W.; HIGGINS,J.; WACHTEL,J.; PERSENSKY,J.J.

    2000-07-30

    The Human-System Interface Design Review Guideline (NUREG-0700, Revision 1) was developed by the US Nuclear Regulatory Commission (NRC) to provide human factors guidance as a basis for the review of advanced human-system interface technologies. The guidance consists of three components: design review procedures, human factors engineering guidelines, and a software application to provide design review support called the ``Design Review Guideline.'' Since it was published in June 1996, Rev. 1 to NUREG-0700 has been used successfully by NRC staff, contractors and nuclear industry organizations, as well as by interested organizations outside the nuclear industry. The NRC has committed to the periodic update and improvement of the guidance to ensure that it remains a state-of-the-art design evaluation tool in the face of emerging and rapidly changing technology. This paper addresses the current research to update of NUREG-0700 based on the substantial work that has taken place since the publication of Revision 1.

  3. Measurement of the ??*?? and ??*??' transition form factors

    SciTech Connect (OSTI)

    del Amo Sanchez, P.; Lees, J. P.; Poireau, V.; Prencipe, E.; Tisserand, V.; Garra Tico, J.; Grauges, E.; Martinelli, M.; Milanes, D. A.; Palano, A.; Pappagallo, M.; Eigen, G.; Stugu, B.; Sun, L.; Brown, D. N.; Kerth, L. T.; Kolomensky, Yu.?G.; Lynch, G.; Osipenkov, I. L.; Koch, H.; Schroeder, T.; Asgeirsson, D. J.; Hearty, C.; Mattison, T. S.; McKenna, J. A.; Khan, A.; Blinov, V. E.; Botov, A. A.; Buzykaev, A. R.; Druzhinin, V. P.; Golubev, V. B.; Kravchenko, E. A.; Onuchin, A. P.; Serednyakov, S. I.; Skovpen, Yu.?I.; Solodov, E. P.; Todyshev, K.?Yu.; Yushkov, A. N.; Bondioli, M.; Curry, S.; Kirkby, D.; Lankford, A. J.; Mandelkern, M.; Martin, E. C.; Stoker, D. P.; Atmacan, H.; Gary, J. W.; Liu, F.; Long, O.; Vitug, G. M.; Campagnari, C.; Hong, T. M.; Kovalskyi, D.; Richman, J. D.; West, C. A.; Eisner, A. M.; Heusch, C. A.; Kroseberg, J.; Lockman, W. S.; Martinez, A. J.; Schalk, T.; Schumm, B. A.; Seiden, A.; Winstrom, L. O.; Cheng, C. H.; Doll, D. A.; Echenard, B.; Hitlin, D. G.; Ongmongkolkul, P.; Porter, F. C.; Rakitin, A. Y.; Andreassen, R.; Dubrovin, M. S.; Meadows, B. T.; Sokoloff, M. D.; Bloom, P. C.; Ford, W. T.; Gaz, A.; Nagel, M.; Nauenberg, U.; Smith, J. G.; Wagner, S. R.; Ayad, R.; Toki, W. H.; Jasper, H.; Petzold, A.; Spaan, B.; Kobel, M. J.; Schubert, K. R.; Schwierz, R.; Bernard, D.; Verderi, M.; Clark, P. J.; Playfer, S.; Watson, J. E.; Andreotti, M.; Bettoni, D.; Bozzi, C.; Calabrese, R.; Cecchi, A.; Cibinetto, G.; Fioravanti, E.; Franchini, P.; Garzia, I.; Luppi, E.; Munerato, M.; Negrini, M.; Petrella, A.; Piemontese, L.; Baldini-Ferroli, R.; Calcaterra, A.; de Sangro, R.; Finocchiaro, G.; Nicolaci, M.; Pacetti, S.; Patteri, P.; Peruzzi, I. M.; Piccolo, M.; Rama, M.; Zallo, A.; Contri, R.; Guido, E.; Lo Vetere, M.; Monge, M. R.; Passaggio, S.; Patrignani, C.; Robutti, E.; Bhuyan, B.; Prasad, V.; Lee, C. L.; Morii, M.; Edwards, A. J.; Adametz, A.; Marks, J.; Uwer, U.; Bernlochner, F. U.; Ebert, M.; Lacker, H. M.; Lueck, T.; Volk, A.; Dauncey, P. D.; Tibbetts, M.; Behera, P. K.; Mallik, U.; Chen, C.; Cochran, J.; Crawley, H. B.; Meyer, W. T.; Prell, S.; Rosenberg, E. I.; Rubin, A. E.; Gritsan, A. V.; Guo, Z. J.; Arnaud, N.; Davier, M.; Derkach, D.; Firmino da Costa, J.; Grosdidier, G.; Le Diberder, F.; Lutz, A. M.; Malaescu, B.; Perez, A.; Roudeau, P.; Schune, M. H.; Serrano, J.; Sordini, V.; Stocchi, A.; Wang, L.; Wormser, G.; Lange, D. J.; Wright, D. M.; Bingham, I.; Chavez, C. A.; Coleman, J. P.; Fry, J. R.; Gabathuler, E.; Hutchcroft, D. E.; Payne, D. J.; Touramanis, C.; Bevan, A. J.; Di Lodovico, F.; Sacco, R.; Sigamani, M.; Cowan, G.; Paramesvaran, S.; Wren, A. C.; Brown, D. N.; Davis, C. L.; Denig, A. G.; Fritsch, M.; Gradl, W.; Hafner, A.; Alwyn, K. E.; Bailey, D.; Barlow, R. J.; Jackson, G.; Lafferty, G. D.; Anderson, J.; Cenci, R.; Jawahery, A.; Roberts, D. A.; Simi, G.; Tuggle, J. M.; Dallapiccola, C.; Salvati, E.; Cowan, R.; Dujmic, D.; Sciolla, G.; Zhao, M.; Lindemann, D.; Patel, P. M.; Robertson, S. H.; Schram, M.; Biassoni, P.; Lazzaro, A.; Lombardo, V.; Palombo, F.; Stracka, S.; Cremaldi, L.; Godang, R.; Kroeger, R.; Sonnek, P.; Summers, D. J.; Nguyen, X.; Simard, M.; Taras, P.; De Nardo, G.; Monorchio, D.; Onorato, G.; Sciacca, C.; Raven, G.; Snoek, H. L.; Jessop, C. P.; Knoepfel, K. J.; LoSecco, J. M.; Wang, W. F.; Corwin, L. A.; Honscheid, K.; Kass, R.; Blount, N. L.; Brau, J.; Frey, R.; Igonkina, O.; Kolb, J. A.; Rahmat, R.; Sinev, N. B.; Strom, D.; Strube, J.; Torrence, E.; Castelli, G.; Feltresi, E.; Gagliardi, N.; Margoni, M.; Morandin, M.; Posocco, M.; Rotondo, M.; Simonetto, F.; Stroili, R.; Ben-Haim, E.; Bomben, M.; Bonneaud, G. R.; Briand, H.; Calderini, G.; Chauveau, J.; Hamon, O.; Leruste, Ph.; Marchiori, G.; Ocariz, J.; Prendki, J.; Sitt, S.; Biasini, M.; Manoni, E.; Rossi, A.; Angelini, C.; Batignani, G.; Bettarini, S.; Carpinelli, M.; Casarosa, G.; Cervelli, A.; Forti, F.; Giorgi, M. A.; Lusiani, A.; Neri, N.; Paoloni, E.; Rizzo, G.; Walsh, J. J.; Lopes Pegna, D.; Lu, C.; Olsen, J.; Smith, A. J. S.; Telnov, A. V.; Anulli, F.; Baracchini, E.; Cavoto, G.; Faccini, R.; Ferrarotto, F.; Ferroni, F.; Gaspero, M.; Li Gioi, L.; Mazzoni, M. A.; Piredda, G.; Renga, F.; Buenger, C.; Hartmann, T.; Leddig, T.; Schröder, H.; Waldi, R.; Adye, T.; Olaiya, E. O.; Wilson, F. F.; Emery, S.; Hamel de Monchenault, G.; Vasseur, G.; Yèche, Ch.; Allen, M. T.; Aston, D.; Bard, D. J.; Bartoldus, R.; Benitez, J. F.; Cartaro, C.; Convery, M. R.; Dorfan, J.; Dubois-Felsmann, G. P.; Dunwoodie, W.; Field, R. C.; Franco Sevilla, M.; Fulsom, B. G.; Gabareen, A. M.; Graham, M. T.; Grenier, P.; Hast, C.; Innes, W. R.; Kelsey, M. H.; Kim, H.; Kim, P.; Kocian, M. L.; Leith, D. W. G. S.; Lewis, P.; Li, S.; Lindquist, B.; Luitz, S.; Luth, V.; Lynch, H. L.

    2011-09-06

    We study the reactions e?e??e?e??(') in the single-tag mode and measure the ??*??(') transition form factors in the momentum-transfer range from 4 to 40 GeV². The analysis is based on 469 fb?¹ of integrated luminosity collected at PEP-II with the BABAR detector at e?e? center-of-mass energies near 10.6 GeV.

  4. Mobil/Marathon takeover. Hearing before a Subcommittee of the Committee on Government Operations, House of Representatives, Ninety-Seventh Congress, First Session, November 19, 1981

    SciTech Connect (OSTI)

    Not Available

    1982-01-01

    The exercise of corporate power and money as well as the effect on energy policy were the underlying issues in a hearing on the proposed merger of Mobil and Marathon oil companies. The use of capital in this way would deny funds for economic recovery and energy development at a time when the oil companies complain that they need more financial incentives. The companies' response in the direction of mergers suggest that deregulation and tax incentives are not developing solutions to energy supply, but are creating new problems. The witnesses included representatives of Ohio, DOE's Office of Competition, and independent oil jobbers and distributors, who argued against the merger. Additional letters and statement from the witnesses follow their testimony. (DCK)

  5. Findings and recommendations of the advisory panel on synthetic fuels. Advisory panel on synthetic fuels. Report for the Committee on Science and Technology, US House of Representatives

    SciTech Connect (OSTI)

    Not Available

    1980-01-01

    In a report to the US House of Representatives Committee on Science and Technology, the Advisory Panel defines the most critical energy problem facing the US: obtaining a sufficient supply of liquid hydrocarbons for transportation fuel and for other applications where substitution would be difficult, costly, and time-consuming. Any substantial contribution from synthetic fuels must involve the use of coal, oil shale, and biomass, with the raw materials coming from as many different regions of the country as possible. The panel makes recommendations regarding (1) the emphasis of the Department of Energy's synthetic-fuel demonstration program, (2) implementation of a synthetic-fuel production program, and (3) mitigation of the environmental and socioeconomic impacts of synthetic-fuel production. The panel specifically maintains that federal assistance to commercial-scale projects should be available on a competitive basis to those organizations willing to take substantial marketing risks.

  6. H. R. 4805: Internal Revenue Code of 1990. Introduced in the House of Representatives, One Hundredth First Congress, Second Session, May 10, 1990

    SciTech Connect (OSTI)

    Not Available

    1990-01-01

    This bill was introduced into the U.S. House of Representatives on May 10, 1990 to amend the Internal Revenue Code of 1986. This bill reduces emissions of carbon dioxide by imposing a tax on certain fuels based on their carbon content. Separate sections are included which impose tax on coal, tax on petroleum, and tax on natural gas. The tax rate on coal will be $3.00 per ton for 1991, $6.00 per ton for 1992, $9.00 per ton for 1993, and $12 per ton for 1994. The tax rate on petroleum will be $.65 per barrel for 1991, $1.30 per barrel for 1992, $1.95 per barrel for 1993, and $2.60 per barrel for 1994. The tax rate on natural gas will be $.08 per MCF for 1991, $.16 per MCF for 1992, $.24 per MCF for 1993, and $.32 per MCF for 1994.

  7. Transcription factor-based biosensors for detecting dicarboxylic acids

    DOE Patents [OSTI]

    Dietrich, Jeffrey; Keasling, Jay

    2014-02-18

    The invention provides methods and compositions for detecting dicarboxylic acids using a transcription factor biosensor.

  8. Identification and Control of Factors that Affect EGR Cooler Fouling |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Control of Factors that Affect EGR Cooler Fouling Identification and Control of Factors that Affect EGR Cooler Fouling Key factors that cause exhaust gas recirculation cooler fouling were identified through extensive literature search and controlled experiment was devised to study the impact of a few key factors on deposition. PDF icon deer08_styles.pdf More Documents & Publications Factors Impacting EGR Cooler Fouling - Main Effects and Interactions The Impact of PM

  9. Form factor dark matter (Journal Article) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Form factor dark matter Citation Details In-Document Search Title: Form factor dark matter We present a dynamical alternative to inelastic dark matter as a way of reconciling the modulating signal seen at DAMA with null results at other direct detection experiments. The essential ingredient is a new form factor which introduces momentum dependence in the interaction of dark matter with nuclei. The role of the form factor is to suppress events at low momentum transfer. We find that a form factor

  10. Human Factors for Situation Assessment in Grid Operations

    SciTech Connect (OSTI)

    Guttromson, Ross T.; Schur, Anne; Greitzer, Frank L.; Paget, Mia L.

    2007-08-08

    Executive Summary Despite advances in technology, power system operators must assimilate overwhelming amounts of data to keep the grid operating. Analyses of recent blackouts have clearly demonstrated the need to enhance the operator’s situation awareness (SA). The long-term objective of this research is to integrate valuable technologies into the grid operator environment that support decision making under normal and abnormal operating conditions and remove non-technical barriers to enable the optimum use of these technologies by individuals working alone and as a team. More specifically, the research aims to identify methods and principles to increase SA of grid operators in the context of system conditions that are representative or common across many operating entities and develop operationally relevant experimental methods for studying technologies and operational practices which contribute to SA. With increasing complexity and interconnectivity of the grid, the scope and complexity of situation awareness have grown. New paradigms are needed to guide research and tool development aimed to enhance and improve operations. In reviewing related research, operating practices, systems, and tools, the present study established a taxonomy that provides a perspective on research and development surrounding power grid situation awareness and clarifies the field of human factors/SA for grid operations. Information sources that we used to identify critical factors underlying SA included interviews with experienced operational personnel, available historical summaries and transcripts of abnormal conditions and outages (e.g., the August 14, 2003 blackout), scientific literature, and operational policies/procedures and other documentation. Our analysis of August 2003 blackout transcripts and interviews adopted a different perspective than previous analyses of this material, and we complemented this analysis with additional interviews. Based on our analysis and a broad literature review, we advocate a new perspective on SA in terms of sensemaking, also called situated or ecological decision making, where the focus of the investigation is to understand why the decision maker(s) experienced the situation the way they did, or why what they saw made sense to them at the time. This perspective is distinct from the traditional branch of human factors research in the field which focuses more on ergonomics and the transactional relationship between the human operator and the systems. Consistent with our findings from the literature review, we recognized an over-arching need to focus SA research on issues surrounding the concept of shared knowledge; e.g., awareness of what is happening in adjacent areas as well as one’s own area of responsibility. Major findings were: a) Inadequate communication/information sharing is pervasive, b) Information is available, but not used. Many tools and mechanisms exist for operators to build awareness of the physical grid system, yet the transcripts reveal that they still need to call and exchange information with operators of neighboring areas to improve or validate their SA. The specific types of information that they request are quite predictable and, in most cases, cover information that could be available to both operators and reliability coordinators through readily available displays or other data sources, c) Shared Knowledge is Required on Operations/Actions as Well as Physical Status. In an ideal, technologically and organizationally perfect world, every control room and every reliability coordinator may have access to complete data across all regional control areas and yet, there would still be reason for the operators to call each other to gain and improve their SA of power grid operations, and d) Situation Awareness as sensemaking and shared knowledge.

  11. Public opinion factors regarding nuclear power

    SciTech Connect (OSTI)

    Benson, B.

    1991-12-31

    This paper is an effort to identify, as comprehensively as possible, public concerns about nuclear power, and to assess, where possible, the relative importance of these concerns as they relate to government regulation of and policy towards nuclear power. It is based on some two dozen in-depth interviews with key communicators representing the nuclear power industry, the environmental community, and government, as well as on the parallel efforts in our research project: (1) review of federal court case law, (2) a selective examination of the Nuclear Regulatory Commission (NRC) administrative process, and (3) the preceding George Mason University research project in this series. The paper synthesizes our findings about public attitudes towards nuclear power as expressed through federal court case law, NRC administrative law, public opinion surveys, and direct personal interviews. In so doing, we describe the public opinion environment in which the nuclear regulatory process must operate. Our premise is that public opinion ultimately underlies the approaches government agencies take towards regulating nuclear power, and that, to the degree that the nuclear power industry`s practices are aligned with public opinion, a more favorable regulatory climate is possible.

  12. Public opinion factors regarding nuclear power

    SciTech Connect (OSTI)

    Benson, B.

    1991-01-01

    This paper is an effort to identify, as comprehensively as possible, public concerns about nuclear power, and to assess, where possible, the relative importance of these concerns as they relate to government regulation of and policy towards nuclear power. It is based on some two dozen in-depth interviews with key communicators representing the nuclear power industry, the environmental community, and government, as well as on the parallel efforts in our research project: (1) review of federal court case law, (2) a selective examination of the Nuclear Regulatory Commission (NRC) administrative process, and (3) the preceding George Mason University research project in this series. The paper synthesizes our findings about public attitudes towards nuclear power as expressed through federal court case law, NRC administrative law, public opinion surveys, and direct personal interviews. In so doing, we describe the public opinion environment in which the nuclear regulatory process must operate. Our premise is that public opinion ultimately underlies the approaches government agencies take towards regulating nuclear power, and that, to the degree that the nuclear power industry's practices are aligned with public opinion, a more favorable regulatory climate is possible.

  13. Assessment of G3(MP2)//B3 theory including a pseudopotential for molecules containing first-, second-, and third-row representative elements

    SciTech Connect (OSTI)

    Rocha, Carlos Murilo Romero; Morgon, Nelson Henrique; Custodio, Rogério; Pereira, Douglas Henrique; Departamento de Ciências Exatas e Biotecnológicas, Universidade Federal do Tocantins, Campus de Gurupi, 77410-530 Gurupi, Tocantins

    2013-11-14

    G3(MP2)//B3 theory was modified to incorporate compact effective potential (CEP) pseudopotentials, providing a theoretical alternative referred to as G3(MP2)//B3-CEP for calculations involving first-, second-, and third-row representative elements. The G3/05 test set was used as a standard to evaluate the accuracy of the calculated properties. G3(MP2)//B3-CEP theory was applied to the study of 247 standard enthalpies of formation, 104 ionization energies, 63 electron affinities, 10 proton affinities, and 22 atomization energies, comprising 446 experimental energies. The mean absolute deviations compared with the experimental data for all thermochemical results presented an accuracy of 1.4 kcal mol{sup ?1} for G3(MP2)//B3 and 1.6 kcal mol{sup ?1} for G3(MP2)//B3-CEP. Approximately 75% and 70% of the calculated properties are found with accuracy between ±2 kcal mol{sup ?1} for G3(MP2)//B3 and G3(MP2)//B3-CEP, respectively. Considering a confidence interval of 95%, the results may oscillate between ±4.2 kcal mol{sup ?1} and ±4.6 kcal mol{sup ?1}, respectively. The overall statistical behavior indicates that the calculations using pseudopotential present similar behavior with the all-electron theory. Of equal importance to the accuracy is the CPU time, which was reduced by between 10% and 40%.

  14. Hamilton study: distribution of factors confounding the relationship between air quality and respiratory health

    SciTech Connect (OSTI)

    Pengelly, L.D.; Kerigan, A.T.; Goldsmith, C.H.; Inman, E.M.

    1984-10-01

    Hamilton, Ontario is an industrial city with a population of 300,000 which is situated at the western end of Lake Ontario. Canada's two largest iron and steel mills are located here; the city historically has had relatively poor air quality, which has improved markedly in the last 25 years. Concern about the health effects of current air quality recently led us to carry out an epidemiological study of the effects of air pollution on the respiratory health of over 3500 school children. Respiratory health was measured by pulmonary function testing of each child, and by an assessment of each child's respiratory symptoms via a questionnaire administered to the parents. Previous studies had shown that other environmental factors (e.g. parental smoking, parental cough, socioeconomic level, housing, and gas cooking) might also affect respiratory health, and thus confound any potential relationships between health and air pollution. The questionnaire also collected information on many of these confounding factors. For the purposes of initial analysis, the city was divided into five areas in which differences in air quality were expected. In general, factors which have been associated with poor respiratory health were observed to be more prevalent in areas of poorer air quality.

  15. High quality factor nanocrystalline diamond micromechanical resonators limited by thermoelastic damping

    SciTech Connect (OSTI)

    Najar, Hadi; Chan, Mei-Lin; Yang, Hsueh-An; Lin, Liwei; Cahill, David G.; Horsley, David A.

    2014-04-14

    We demonstrate high quality factor thin-film nanocrystalline diamond micromechanical resonators with quality factors limited by thermoelastic damping. Cantilevers, single-anchored and double-anchored double-ended tuning forks, were fabricated from 2.5??m thick in-situ boron doped nanocrystalline diamond films deposited using hot filament chemical vapor deposition. Thermal conductivity measured by time-domain thermoreflectance resulted in 24?±?3?W m{sup ?1} K{sup ?1} for heat transport through the thickness of the diamond film. The resonant frequencies of the fabricated resonators were 46?kHz–8?MHz and showed a maximum measured Q???86?000 at f{sub n}?=?46.849?kHz. The measured Q-factors are shown to be in good agreement with the limit imposed by thermoelastic dissipation calculated using the measured thermal conductivity. The mechanical properties extracted from resonant frequency measurements indicate a Young's elastic modulus of ?788?GPa, close to that of microcrystalline diamond.

  16. Various factors affect coiled tubing limits

    SciTech Connect (OSTI)

    Yang, Y.S.

    1996-01-15

    Safety and reliability remain the primary concerns in coiled tubing operations. Factors affecting safety and reliability include corrosion, flexural bending, internal (or external) pressure and tension (or compression), and mechanical damage due to improper use. Such limits as coiled tubing fatigue, collapse, and buckling need to be understood to avoid disaster. With increased use of coiled tubing, operators will gain more experience. But at the same time, with further research and development of coiled tubing, the manufacturing quality will be improved and fatigue, collapse, and buckling models will become more mature, and eventually standard specifications will be available. This paper reviews the uses of coiled tubing and current research on mechanical behavior of said tubing. It also discusses several models used to help predict fatigue and failure levels.

  17. Chiral corrections to hyperon axial form factors

    SciTech Connect (OSTI)

    Jiang Fujiun; Tiburzi, B. C.

    2008-05-01

    We study the complete set of flavor-changing hyperon axial-current matrix elements at small momentum transfer. Using partially quenched heavy baryon chiral perturbation theory, we derive the chiral and momentum behavior of the axial and induced pseudoscalar form factors. The meson pole contributions to the latter posses a striking signal for chiral physics. We argue that the study of hyperon axial matrix elements enables a systematic lattice investigation of the efficacy of three-flavor chiral expansions in the baryon sector. This can be achieved by considering chiral corrections to SU(3) symmetry predictions, and their partially quenched generalizations. In particular, despite the presence of eight unknown low-energy constants, we are able to make next-to-leading order symmetry breaking predictions for two linear combinations of axial charges.

  18. Kallotenue papyrolyticum gen. nov., sp. nov., a cellulolytic and filamentous thermophile that represents a novel lineage (Kallotenuales ord. nov., Kallotenuaceae fam. nov.) within the class Chloroflexia

    SciTech Connect (OSTI)

    Cole, Jesse; Gieler, Brandon; Heisler, Devon; Palisoc, Maryknoll; Williams, Amanda; Dohnalkova, Alice; Ming, Hong; Yu, Tian T.; Dodsworth, Jeremy A.; Li, Wen J.; Hedlund, Brian P.

    2013-08-15

    Several closely-related, thermophilic, and cellulolytic bacterial strains, designated JKG1T, JKG2, JKG3, JKG4, and JKG5, were isolated from a cellulolytic enrichment (corn stover) incubated in the water column of Great Boiling Spring, NV. Strain JKG1T had cells of a diameter of 0.7 - 0.9 ?m and length of ~2.0 ?m that formed non-branched multicellular filaments reaching >300 ?m. Spores were not formed and dense liquid cultures were red. The temperature range for growth was 45-65 °C, with an optimum of 55 °C. The pH range for growth was 5.6-9.0, with an optimum of 7.5. JKG1T grew as an aerobic heterotroph, utilizing glucose, sucrose, xylose, arabinose, cellobiose, carboxymethylcellulose, filter paper, microcrystalline cellulose, xylan, starch, casamino acids, tryptone, peptone, yeast extract, acetate, citrate, lactate, pyruvate, and glycerol as sole carbon sources, and was not observed to photosynthesize. The cells stained Gram-negative. Phylogenetic analysis using 16S rRNA gene sequences placed the new isolates in the class Chloroflexia, but distant from other cultivated members, with the highest sequence identity of 82.5% to Roseiflexus castenholzii. The major quinone was menaquinone-9; no ubiquinones were detected. The major cellular fatty acids (>5%) were C18:0, anteiso-C17:0, iso-C18:0, and iso-C17:0. C16:0, iso-C16:0, and C17:0. The peptidoglycan amino acids were alanine, ornithine, glutamic acid, serine, and asparagine. Whole-cell sugars included mannose, rhamnose, glucose, galactose, ribose, arabinose, and xylose. Morphological, phylogenetic, and chemotaxonomic results suggest that JKG1T is representative of a new lineage within the class Chloroflexia, which we propose to designate Kallotenue papyrolyticum gen. nov., sp. nov., Kallotenuaceae fam. nov., Kallotenuales ord. nov.

  19. Improved recovery from Gulf of Mexico reservoirs. Volume III (of 4): Characterization and simulation of representative resources. Final report, February 14, 1995--October 13, 1996

    SciTech Connect (OSTI)

    Kimbrell, W.C.; Bassiouni, Z.A.; Bourgoyne, A.T.

    1997-01-13

    Significant innovations have been made in seismic processing and reservoir simulation. In addition, significant advances have been made in deviated and horizontal drilling technologies. Effective application of these technologies along with improved integrated resource management methods offer opportunities to significantly increase Gulf of Mexico production, delay platform abandonments, and preserve access to a substantial remaining oil target for both exploratory drilling and advanced recovery processes. In an effort to illustrate the impact that these new technologies and sources of information can have upon the estimates of recoverable oil in the Gulf of Mexico, additional and detailed data was collected for two previously studied reservoirs: a South March Island reservoir operated by Taylor Energy and Gulf of Mexico reservoir operated by Mobil, whose exact location has been blind-coded at their request, and an additional third representative reservoir in the Gulf of Mexico, the KEKF-1 reservoir in West Delta Block 84 Field. The new data includes reprocessed 2-D seismic data, newly acquired 3-D data, fluid data, fluid samples, pressure data, well test data, well logs, and core data/samples. The new data was used to refine reservoir and geologic characterization of these reservoirs. Further laboratory investigation also provided additional simulation input data in the form of PVT properties, relative permeabilities, capillary pressures, and water compatibility. Geologic investigations were also conducted to refine the models of mud-rich submarine fan architectures used by seismic analysts and reservoir engineers. These results were also used, in part, to assist in the recharacterization of these reservoirs.

  20. Spatially Resolved Estimation of Ozone-related Mortality in the United States under Two Representative Concentration Pathways (RCPs) and their Uncertainty

    SciTech Connect (OSTI)

    Kim, Young-Min; Zhou, Ying; Gao, Yang; Fu, Joshua S.; Johnson, Brent; Huang, Cheng; Liu, Yang

    2015-01-01

    BACKGROUND: The spatial pattern of the uncertainty in climate air pollution health impact has rarely been studied due to the lack of high-resolution model simulations, especially under the latest Representative Concentration Pathways (RCPs). OBJECTIVES: We estimated county-level ozone (O3) and PM2.5 related excess mortality (EM) and evaluated the associated uncertainties in the continental United States in the 2050s under RCP4.5 and RCP8.5. METHODS: Using dynamically downscaled climate model simulations, we calculated changes in O3 and PM2.5 levels at 12 km resolution between the future (2057-2059) and present (2001-2004) under two RCP scenarios. Using concentration-response relationships in the literature and projected future populations, we estimated EM attributable to the changes in O3 and PM2.5. We finally analyzed the contribution of input variables to the uncertainty in the county-level EM estimation using Monte Carlo simulation. RESULTS: O3-related premature deaths in the continental U.S. were estimated to be 1,082 deaths/year under RCP8.5 (95% confidence interval (CI): -288 to 2,453), and -5,229 deaths/year under RCP4.5 (-7,212 to -3,246). Simulated PM2.5 changes resulted in a significant decrease in EM under the two RCPs. The uncertainty of O3-related EM estimates was mainly caused by RCP scenarios, whereas that of PM2.5-related EMs was mainly from concentration-response functions. CONCLUSION: EM estimates attributable to climate change-induced air pollution change as well as the associated uncertainties vary substantially in space, and so are the most influential input variables. Spatially resolved data is crucial to develop effective mitigation and adaptation policy.

  1. Poster — Thur Eve — 03: Application of the non-negative matrix factorization technique to [{sup 11}C]-DTBZ dynamic PET data for the early detection of Parkinson's disease

    SciTech Connect (OSTI)

    Lee, Dong-Chang; Jans, Hans; McEwan, Sandy; Riauka, Terence; Martin, Wayne; Wieler, Marguerite

    2014-08-15

    In this work, a class of non-negative matrix factorization (NMF) technique known as alternating non-negative least squares, combined with the projected gradient method, is used to analyze twenty-five [{sup 11}C]-DTBZ dynamic PET/CT brain data. For each subject, a two-factor model is assumed and two factors representing the striatum (factor 1) and the non-striatum (factor 2) tissues are extracted using the proposed NMF technique and commercially available factor analysis software “Pixies”. The extracted factor 1 and 2 curves represent the binding site of the radiotracer and describe the uptake and clearance of the radiotracer by soft tissues in the brain, respectively. The proposed NMF technique uses prior information about the dynamic data to obtain sample time-activity curves representing the striatum and the non-striatum tissues. These curves are then used for “warm” starting the optimization. Factor solutions from the two methods are compared graphically and quantitatively. In healthy subjects, radiotracer uptake by factors 1 and 2 are approximately 35–40% and 60–65%, respectively. The solutions are also used to develop a factor-based metric for the detection of early, untreated Parkinson's disease. The metric stratifies healthy subjects from suspected Parkinson's patients (based on the graphical method). The analysis shows that both techniques produce comparable results with similar computational time. The “semi-automatic” approach used by the NMF technique allows clinicians to manually set a starting condition for “warm” starting the optimization in order to facilitate control and efficient interaction with the data.

  2. Fragmentation, NRQCD and Factorization in Heavy Quarkonium Production

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Fragmentation, NRQCD and Factorization in Heavy Quarkonium Production Citation Details In-Document Search Title: Fragmentation, NRQCD and Factorization in Heavy Quarkonium Production We discuss factorization in heavy quarkonium production in high energy collisions using NRQCD. Infrared divergences at NNLO are not matched by conventional NRQCD matrix elements. However, we show that gauge invariance and factorization require that conventional NRQCD

  3. Major Risk Factors Integrated Facility Disposition Project - Oak Ridge |

    Energy Savers [EERE]

    Department of Energy Integrated Facility Disposition Project - Oak Ridge Major Risk Factors Integrated Facility Disposition Project - Oak Ridge Full Document and Summary Versions are available for download PDF icon Major Risk Factors Integrated Facility Disposition Project - Oak Ridge PDF icon Summary - Major Risk Factors Integrated Facility Disposition Project (IFDP) Oak Ridge, TN More Documents & Publications Major Risk Factors to the Integrated Facility Disposition Project Compilation

  4. Study of Factors Affecting Shrub Establishment on the Monticello, Utah,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Disposal Cell Cover | Department of Energy Study of Factors Affecting Shrub Establishment on the Monticello, Utah, Disposal Cell Cover Study of Factors Affecting Shrub Establishment on the Monticello, Utah, Disposal Cell Cover Study of Factors Affecting Shrub Establishment on the Monticello, Utah, Disposal Cell Cover PDF icon Study of Factors Affecting Shrub Establishment on the Monticello, Utah, Disposal Cell Cover More Documents & Publications Changes in Vegetation at the Monticello,

  5. Voluntary Reporting of Greenhouse Gases Program - Electricity Factors

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    Voluntary Reporting Program > Coefficients Voluntary Reporting of Greenhouse Gases Program (Voluntary Reporting of Greenhouse Gases Program Fuel Carbon Dioxide Emission Coefficients) Voluntary Reporting of Greenhouse Gases Program Fuel Emission Coefficients Table 1: Carbon Dioxide Emission Factors for Stationary Combustion Table 2: Carbon Dioxide Emission Factors for Transportation Fuels Table 3: Generic Methane and Nitrous Oxide Emission Factors for Stationary Fuel Combustion Table 4:

  6. Human Factors Aspects of Operating Small Reactors

    SciTech Connect (OSTI)

    OHara, J.M.; Higgins, J.; Deem, R.; Xing, J.; DAgostino, A.

    2010-11-07

    The nuclear-power community has reached the stage of proposing advanced reactor designs to support power generation for decades to come. They are considering small modular reactors (SMRs) as one approach to meet these energy needs. While the power output of individual reactor modules is relatively small, they can be grouped to produce reactor sites with different outputs. Also, they can be designed to generate hydrogen, or to process heat. Many characteristics of SMRs are quite different from those of current plants, and so may require a concept of operations (ConOps) that also is different. The U.S. Nuclear Regulatory Commission (NRC) has begun examining the human factors engineering- (HFE) and ConOps- aspects of SMRs; if needed, they will formulate guidance to support SMR licensing reviews. We developed a ConOps model, consisting of the following dimensions: Plant mission; roles and responsibilities of all agents; staffing, qualifications, and training; management of normal operations; management of off-normal conditions and emergencies; and, management of maintenance and modifications. We are reviewing information on SMR design to obtain data about each of these dimensions, and have identified several preliminary issues. In addition, we are obtaining operations-related information from other types of multi-module systems, such as refineries, to identify lessons learned from their experience. Here, we describe the project's methodology and our preliminary findings.

  7. Confinement and the safety factor profile

    SciTech Connect (OSTI)

    Batha, S.H.; Levinton, F.M.; Scott, S.D.

    1995-12-01

    The conjecture that the safety factor profile, q(r), controls the improvement in tokamak plasmas from poor confinement in the Low (L-) mode regime to improved confinement in the supershot regime has been tested in two experiments on the Tokamak Fusion Test Reactor (TFTR). First, helium was puffed into the beam-heated phase of a supershot discharge which induced a degradation from supershot to L-mode confinement in about 100 msec, far less than the current relaxation time. The q and shear profiles measured by a motional Stark effect polarimeter showed little change during the confinement degradation. Second, rapid current ramps in supershot plasmas altered the q profile, but were observed not to change significantly the energy confinement. Thus, enhanced confinement in supershot plasmas is not due to a particular q profile which has enhanced stability or transport properties. The discharges making a continuous transition between supershot and L-mode confinement were also used to test the critical-electron-temperature-gradient transport model. It was found that this model could not reproduce the large changes in electron and ion temperature caused by the change in confinement.

  8. A new friction factor correlation for laminar, single-phase flows through rock fractures

    SciTech Connect (OSTI)

    Nazridoust, K. (Clarkson Univ., Potsdam, NY); Ahmadi, G. (Clarkson Univ., Potsdam, NY); Smith, D.H.

    2006-09-30

    Single-phase flow through fractured media occurs in various situations, such as transport of dissolved contaminants through geological strata, sequestration of carbon dioxide in depleted gas reservoirs, and in primary oil recovery. In the present study, fluid flows through a rock fracture were simulated. The fracture geometry was obtained from the CT scans of a rock fracture produced by the Brazilian method in a sandstone sample. A post-processing code using a CAD package was developed and used to generate the three-dimensional fracture from the CT scan data. Several sections along the fracture were considered and the GambitTM code was used to generate unstructured grids for flow simulations. FLUENTTM was used to analyze the flow conditions through the fracture section for different flow rates. Because of the small aperture of the fractures, the gravitational effects could be neglected. It was confirmed that the pressure drop was dominated by the smallest aperture passages of the fracture. The accuracy of parallel plate models for estimating the pressure drops through fractures was studied. It was shown that the parallel plate flow model with the use of an appropriate effective fracture aperture and inclusion of the tortuosity factor could provide reasonable estimates for pressure drops in the fracture. On the basis of the CFD simulation data, a new expression for the friction factor for flows through fractures was developed. The new model predictions were compared with the simulation results and favorable agreement was found. It was shown that when the length of the fracture and the mean and standard deviation of the fracture are known, the pressure loss as a function of the flow rate could be estimated. These findings may prove useful for design of lab experiments, computational studied of flows through real rock fractures, or inclusions in simulators for large-scale flows in highly fractured rocks.

  9. Written Statement of Mark Whitney Acting Assistant Secretary for Environmental Management United States Department of Energy Before the Subcommittee on Energy and Water Development Committee on Appropriations United States House of Representatives

    Broader source: Energy.gov [DOE]

    Written Statement of Mark Whitney Acting Assistant Secretary for Environmental Management United States Department of Energy Before the Subcommittee on Energy and Water Development Committee on Appropriations United States House of Representatives (March 18, 2015)

  10. Written Statement of Dr. Monica Regalbuto Assistant Secretary for Environmental Management United States Department of Energy Before the Subcommittee on Strategic Forces Committee on Armed Services United States House of Representatives (February 11 2016)

    Broader source: Energy.gov [DOE]

    Written Statement of Dr. Monica Regalbuto Assistant Secretary for Environmental Management United States Department of Energy Before the Subcommittee on Strategic Forces Committee on Armed Services United States House of Representatives February 11, 2016.

  11. LPS-inducible factor(s) from activated macrophages mediates cytolysis of Naegleria fowleri amoebae

    SciTech Connect (OSTI)

    Cleary, S.F.; Marciano-Cabral, F.

    1986-03-01

    Soluble cytolytic factors of macrophage origin have previously been described with respect to their tumoricidal activity. The purpose of this study was to investigate the mechanism and possible factor(s) responsible for cytolysis of the amoeba Naegleria fowleri by activated peritoneal macrophages from B6C3F1 mice. Macrophages or conditioned medium (CM) from macrophage cultures were incubated with /sup 3/H-Uridine labeled amoebae. Percent specific release of label served as an index of cytolysis. Bacille Calmette-Guerin (BCG) and Corynebacterium parvum macrophages demonstrated significant cytolysis of amoebae at 24 h with an effector to target ratio of 10:1. Treatment of macrophages with inhibitors of RNA or protein synthesis blocked amoebicidal activity. Interposition of a 1 ..mu..m pore membrane between macrophages and amoebae inhibited killing. Inhibition in the presence of the membrane was overcome by stimulating the macrophages with LPS. CM from SPS-stimulated, but not unstimulated, cultures of activated macrophages was cytotoxic for amoebae. The activity was heat sensitive and was recovered from ammonium sulfate precipitation of the CM. Results indicate that amoebicidal activity is mediated by a protein(s) of macrophage origin induced by target cell contact or stimulation with LPS.

  12. Nominal Performance Biosphere Dose Conversion Factor Analysis

    SciTech Connect (OSTI)

    Wasiolek, Maryla A.

    2000-12-21

    The purpose of this report was to document the process leading to development of the Biosphere Dose Conversion Factors (BDCFs) for the postclosure nominal performance of the potential repository at Yucca Mountain. BDCF calculations concerned twenty-four radionuclides. This selection included sixteen radionuclides that may be significant nominal performance dose contributors during the compliance period of up to 10,000 years, five additional radionuclides of importance for up to 1 million years postclosure, and three relatively short-lived radionuclides important for the human intrusion scenario. Consideration of radionuclide buildup in soil caused by previous irrigation with contaminated groundwater was taken into account in the BDCF development. The effect of climate evolution, from the current arid conditions to a wetter and cooler climate, on the BDCF values was evaluated. The analysis included consideration of different exposure pathway's contribution to the BDCFs. Calculations of nominal performance BDCFs used the GENII-S computer code in a series of probabilistic realizations to propagate the uncertainties of input parameters into the output. BDCFs for the nominal performance, when combined with the concentrations of radionuclides in groundwater allow calculation of potential radiation doses to the receptor of interest. Calculated estimates of radionuclide concentration in groundwater result from the saturated zone modeling. The integration of the biosphere modeling results (BDCFs) with the outcomes of the other component models is accomplished in the Total System Performance Assessment (TSPA) to calculate doses to the receptor of interest from radionuclides postulated to be released to the environment from the potential repository at Yucca Mountain.

  13. CT head-scan dosimetry in an anthropomorphic phantom and associated measurement of ACR accreditation-phantom imaging metrics under clinically representative scan conditions

    SciTech Connect (OSTI)

    Brunner, Claudia C.; Stern, Stanley H.; Chakrabarti, Kish; Minniti, Ronaldo; Parry, Marie I.; Skopec, Marlene

    2013-08-15

    Purpose: To measure radiation absorbed dose and its distribution in an anthropomorphic head phantom under clinically representative scan conditions in three widely used computed tomography (CT) scanners, and to relate those dose values to metrics such as high-contrast resolution, noise, and contrast-to-noise ratio (CNR) in the American College of Radiology CT accreditation phantom.Methods: By inserting optically stimulated luminescence dosimeters (OSLDs) in the head of an anthropomorphic phantom specially developed for CT dosimetry (University of Florida, Gainesville), we measured dose with three commonly used scanners (GE Discovery CT750 HD, Siemens Definition, Philips Brilliance 64) at two different clinical sites (Walter Reed National Military Medical Center, National Institutes of Health). The scanners were set to operate with the same data-acquisition and image-reconstruction protocols as used clinically for typical head scans, respective of the practices of each facility for each scanner. We also analyzed images of the ACR CT accreditation phantom with the corresponding protocols. While the Siemens Definition and the Philips Brilliance protocols utilized only conventional, filtered back-projection (FBP) image-reconstruction methods, the GE Discovery also employed its particular version of an adaptive statistical iterative reconstruction (ASIR) algorithm that can be blended in desired proportions with the FBP algorithm. We did an objective image-metrics analysis evaluating the modulation transfer function (MTF), noise power spectrum (NPS), and CNR for images reconstructed with FBP. For images reconstructed with ASIR, we only analyzed the CNR, since MTF and NPS results are expected to depend on the object for iterative reconstruction algorithms.Results: The OSLD measurements showed that the Siemens Definition and the Philips Brilliance scanners (located at two different clinical facilities) yield average absorbed doses in tissue of 42.6 and 43.1 mGy, respectively. The GE Discovery delivers about the same amount of dose (43.7 mGy) when run under similar operating and image-reconstruction conditions, i.e., without tube current modulation and ASIR. The image-metrics analysis likewise showed that the MTF, NPS, and CNR associated with the reconstructed images are mutually comparable when the three scanners are run with similar settings, and differences can be attributed to different edge-enhancement properties of the applied reconstruction filters. Moreover, when the GE scanner was operated with the facility's scanner settings for routine head exams, which apply 50% ASIR and use only approximately half of the 100%-FBP dose, the CNR of the images showed no significant change. Even though the CNR alone is not sufficient to characterize the image quality and justify any dose reduction claims, it can be useful as a constancy test metric.Conclusions: This work presents a straightforward method to connect direct measurements of CT dose with objective image metrics such as high-contrast resolution, noise, and CNR. It demonstrates that OSLD measurements in an anthropomorphic head phantom allow a realistic and locally precise estimation of magnitude and spatial distribution of dose in tissue delivered during a typical CT head scan. Additional objective analysis of the images of the ACR accreditation phantom can be used to relate the measured doses to high contrast resolution, noise, and CNR.

  14. Cold Crucible Induction Melter (CCIM) Demonstration Using a Representative Savannah River Site Sludge Simulant On the Large-Size Pilot Platform at the CEA-Marcoule

    SciTech Connect (OSTI)

    Girold, C.; Delaunay, M.; Dussossoy, J.L.; Lacombe, J. [CEA Marcoule, CEA/DEN/DTCD/SCDV, 30 (France); Marra, S.; Peeler, D.; Herman, C.; Smith, M.; Edwards, R.; Barnes, A.; Stone, M. [Savannah River National Laboratory (SRNL), Washington Savannah River Company, Savannah River Site, Aiken, SC (United States); Iverson, D. [Liquid Waste Operations, Washington Savannah River Company (WSRC), Aiken, SC (United States); Do Quang, R. [AREVA NC, Tour AREVA, 92 - Paris La Defense (France); Tchemitcheff, E. [AREVA Federal Services LLC, Richland Office, Richland, WA (United States); Veyer, C. [Consultant, 59 - Saint Waast la Vallee (France)

    2008-07-01

    The cold-crucible induction melter technology (CCIM) is considered worldwide for industrial implementation to overcome the current limits of high level waste vitrification technologies and to answer future challenges such as: new or difficult sludge compositions, need for improving waste loading, need for high temperatures, and corrosive effluents. More particularly, this technology is being considered for implementation at the US DOE Savannah River site to increase the rate of waste processing while reducing the number of HLW canisters to be produced through increased waste loading and improved waste throughput. A collaborative program involving AREVA, CEA (French Atomic Energy Commission), SRNL (Savannah River National Laboratory) and WSRC (Washington Savannah River Company) has thus been initiated in 2007 to demonstrate vitrification with waste loadings on the order of 50% (versus the current DWPF waste loading of about 35%) with a PUREX-type waste composition (high Fe{sub 2}O{sub 3} composition), and to perform two pilot-scale runs on the large size platform equipped with a 650 mm diameter CCIM at the CEA Marcoule. The objectives of the demonstrations were 1) to show the feasibility of processing a representative SRS sludge surrogate using continuous slurry feeding, 2) to produce a glass that would meet the acceptance specifications with an increased waste loading when compared to what is presently achieved at the DWPF, and 3) achieve improved waste throughputs. This presentation describes the platform and the very encouraging results obtained from the demonstration performed at temperatures, specific throughputs and waste loadings that overcome current DWPF limits. Results from the initial exploratory run and second demonstration run include 1) production of a glass product that achieved the targeted glass composition that was more durable than the standard Environmental Assessment (EA) glass, 2) successful slurry feeding of the CCIM, and 3) promising waste processing rates (at 1250 deg. C and 1300 deg. C melt pool temperature) that could result in processing of the Savannah River HLW faster than could be currently achieved with the existing Joule Heated melter in DWPF. In conclusion, this joint effort conducted by CEA, AREVA, SRNL and WSRC led to very encouraging results, demonstrating waste throughputs 44 % that of the DWPF ceramic melter throughput in a 650 mm CCIM melter for the same waste type with a Sludge Batch 3 PUREX-type waste feed flux of 150 L/h/m{sup 2} demonstrated at 1250 deg. C. The very high waste loading (above 52%) allows reducing the amount of glass to be produced by about 27% to treat the same amount of waste when compared to previous DWPF operation for this specific type of feed, since 27 % less glass is needed to immobilize the same amount of waste. It was also demonstrated, for this type of feed, an unusual behavior with regard to nepheline formation, which would require further evaluation for future applications. The product from the baseline demonstration run, with a waste loading of at least 52%, displayed a very good quality. Stabilized operation close to the maximum throughput was demonstrated. Cesium volatility was apparently between 7 and 12 % (based on glass analysis); however this value is only preliminary. This demonstration also allowed the CEA to better understand the SRS slurry feed behavior and to propose adaptations to the platform for any future demonstrations using this type of feed. Finally, use of a large diameter CCIM ({approx}1 meter) may allow faster processing of the SRS HLW than can be achieved with the current DWPF melter. (authors)

  15. Astrophysical S factors for radiative proton capture by {sup 3}H and {sup 7}Li nuclei

    SciTech Connect (OSTI)

    Dubovichenko, S. B.

    2011-03-15

    Within the potential cluster model where orbital states are classified according to Young diagrams and isospin, astrophysical S factors are considered for radiative proton capture by {sup 3}H and {sup 7}Li nuclei at energies of up to 1 and 10 keV, respectively. It is shown that the approach used, which takes into account only the E1 transition for the p{sup 3}H capture process, makes it possible to describe well the most recent experimental data at c.m. energies in the range from 50 keV to 5MeV. In the case of proton capture by {sup 7}Li nuclei, an M1 processwas taken into account in addition to the E1 transition, and a general behavior and the magnitude of the experimental S factor could be correctly reproduced owing to this at astrophysical energies, including the region around the resonance at 0.441 MeV (in the laboratory frame).

  16. Towards a Resolution of the Proton Form Factor Problem: New Electron and Positron Scattering Data

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adikaram, D.; Rimal, D.; Weinstein, L. B.; Raue, B.; Khetarpal, P.; Bennett, R.; Arrington, J.; Brooks, W.; Adhikari, K.; Afanasev, A.; et al

    2015-02-10

    There is a significant discrepancy between the values of the proton electric form factor, GpE, extracted using unpolarized and polarized electron scattering. Calculations predict that small two-photon exchange (TPE) contributions can significantly affect the extraction of GpE from the unpolarized electron-proton cross sections. We determined the TPE contribution by measuring the ratio of positron-proton to electron-proton elastic scattering cross sections using a simultaneous, tertiary electron-positron beam incident on a liquid hydrogen target and detecting the scattered particles in the Jefferson Lab CLAS detector. This novel technique allowed us to cover a wide range in virtual photon polarization (epsilon) and momentummore » transfer (Q2) simultaneously, as well as to cancel luminosity-related systematic errors. The cross section ratio increases with decreasing ε at Q2=1.45 GeV2. This measurement is consistent with the size of the form factor discrepancy at Q2≈1.75 GeV2 and with hadronic calculations including nucleon and Delta intermediate states, which have been shown to resolve the discrepancy up to 2-3 GeV2.« less

  17. Towards a Resolution of the Proton Form Factor Problem: New Electron and Positron Scattering Data

    SciTech Connect (OSTI)

    Adikaram, D.; Rimal, D.; Weinstein, L. B.; Raue, B.; Khetarpal, P.; Bennett, R.; Arrington, J.; Brooks, W.; Adhikari, K.; Afanasev, A.; Amaryan, M.; Anderson, M.; Anefalos Pereira, S.; Avakian, H.; Ball, J.; Battaglieri, M.; Bedlinskiy, I.; Biselli, A.; Bono, J.; Boiarinov, S.; Briscoe, W.; Burkert, V.; Carman, D.; Careccia, S.; Celentano, A.; Chandavar, S.; Charles, G.; Colaneri, L.; Cole, P.; Contalbrigo, M.; Crede, V.; D'Angelo, A.; Dashyan, N.; De Vita, R.; De Sanctis, E.; Deur, A.; Djalali, C.; Dodge, G.; Dupre, R.; Egiyan, H.; El Alaoui, A.; El Fassi, L.; Elouadrhiri, L.; Eugenio, P.; Fedotov, G.; Fegan, S.; Filippi, A.; Fleming, J.; Fradi, A.; Garillon, B.; Gilfoyle, G.; Giovanetti, K.; Girod, F.; Goetz, J.; Gohn, W.; Golovatch, E.; Gothe, R.; Griffioen, K.; Guegan, B.; Guidal, M.; Guo, L.; Hafidi, K.; Hakobyan, H.; Hanretty, C.; Harrison, N.; Hattawy, M.; Hicks, K.; Holtrop, M.; Hughes, S.; Hyde, C. E.; Ilieva, Y.; Ireland, D.; Ishkhanov, B.; Jenkins, D.; Jiang, H.; Jo, H.; Joo, K.; Joosten, S.; Kalantarians, N.; Keller, D.; Khandaker, M.; Kim, A.; Kim, W.; Klein, A.; Klein, F.; Koirala, S.; Kubarovsky, V.; Kuhn, S.; Livingston, K.; Lu, H.; MacGregor, I.; Markov, N.; Mattione, P.; Mayer, M.; McKinnon, B.; Mestayer, M.; Meyer, C.; Mirazita, M.; Mokeev, V.; Montgomery, R.; Moody, C.; Moutarde, H.; Movsisyan, A.; Camacho, C. Munoz; Nadel-Turonski, P.; Niccolai, S.; Niculescu, G.; Osipenko, M.; Ostrovidov, A.; Park, K.; Pasyuk, E.; Pisano, S.; Pogorelko, O.; Price, J.; Procureur, S.; Prok, Y.; Protopopescu, D.; Puckett, A.; Ripani, M.; Rizzo, A.; Rosner, G.; Rossi, P.; Roy, P.; Sabati, F.; Salgado, C.; Schott, D.; Schumacher, R.; Seder, E.; Sharabian, Y.; Simonyan, A.; Skorodumina, I.; Smith, E.; Smith, G.; Sober, D.; Sokhan, D.; Sparveris, N.; Stepanyan, S.; Stoler, P.; Strauch, S.; Sytnik, V.; Taiuti, M.; Tian, Ye; Trivedi, A.; Ungaro, M.; Voskanyan, H.; Voutier, E.; Walford, N.; Watts, D.; Wei, X.; Wood, M.; Zachariou, N.; Zana, L.; Zhang, J.; Zhao, Z.; Zonta, I.

    2015-02-10

    There is a significant discrepancy between the values of the proton electric form factor, GpE, extracted using unpolarized and polarized electron scattering. Calculations predict that small two-photon exchange (TPE) contributions can significantly affect the extraction of GpE from the unpolarized electron-proton cross sections. We determined the TPE contribution by measuring the ratio of positron-proton to electron-proton elastic scattering cross sections using a simultaneous, tertiary electron-positron beam incident on a liquid hydrogen target and detecting the scattered particles in the Jefferson Lab CLAS detector. This novel technique allowed us to cover a wide range in virtual photon polarization (epsilon) and momentum transfer (Q2) simultaneously, as well as to cancel luminosity-related systematic errors. The cross section ratio increases with decreasing ? at Q2=1.45 GeV2. This measurement is consistent with the size of the form factor discrepancy at Q2?1.75 GeV2 and with hadronic calculations including nucleon and Delta intermediate states, which have been shown to resolve the discrepancy up to 2-3 GeV2.

  18. Factors influencing the transport of actinides in the groundwater environment. Final report

    SciTech Connect (OSTI)

    Sheppard, J.C.; Kittrick, J.A.

    1983-07-31

    This report summarizes investigations of factors that significantly influence the transport of actinide cations in the groundwater environment. Briefly, measurements of diffusion coefficients for Am(III), Cm(III), and Np(V) in moist US soils indicated that diffusion is negligible compared to mass transport in flowing groundwater. Diffusion coefficients do, however, indicate that, in the absence of flowing water, actinide elements will migrate only a few centimeters in a thousand years. The remaining investigations were devoted to the determination of distribution ratios (K/sub d/s) for representative US soils, factors influencing them, and chemical and physical processes related to transport of actinides in groundwaters. The computer code GARD was modified to include complex formation to test the importance of humic acid complexing on the rate of transport of actinides in groundwaters. Use of the formation constant and a range of humic acid, even at rather low concentrations of 10/sup -5/ to 10/sup -6/ molar, significantly increases the actinide transport rate in a flowing aquifer. These computer calculations show that any strong complexing agent will have a similar effect on actinide transport in the groundwater environment. 32 references, 9 figures.

  19. Dose factor entry and display tool for BNCT radiotherapy

    DOE Patents [OSTI]

    Wessol, Daniel E. (Bozeman, MT); Wheeler, Floyd J. (Idaho Falls, ID); Cook, Jeremy L. (Greeley, CO)

    1999-01-01

    A system for use in Boron Neutron Capture Therapy (BNCT) radiotherapy planning where a biological distribution is calculated using a combination of conversion factors and a previously calculated physical distribution. Conversion factors are presented in a graphical spreadsheet so that a planner can easily view and modify the conversion factors. For radiotherapy in multi-component modalities, such as Fast-Neutron and BNCT, it is necessary to combine each conversion factor component to form an effective dose which is used in radiotherapy planning and evaluation. The Dose Factor Entry and Display System is designed to facilitate planner entry of appropriate conversion factors in a straightforward manner for each component. The effective isodose is then immediately computed and displayed over the appropriate background (e.g. digitized image).

  20. QCD Factorization for heavy quarkonium production at collider energies

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect QCD Factorization for heavy quarkonium production at collider energies Citation Details In-Document Search Title: QCD Factorization for heavy quarkonium production at collider energies In this talk, I briefly review several models of the heavy quarkonium production at collider energies, and discuss the status of QCD factorization for these production models. Authors: Qiu Jianwei [1] ; Physics Department, Brookhaven National Laboratory, Upton, New York

  1. Factors Affecting PMU Installation Costs (October 2014) | Department of

    Energy Savers [EERE]

    Energy Factors Affecting PMU Installation Costs (October 2014) Factors Affecting PMU Installation Costs (October 2014) The Department of Energy investigated the major cost factors that affected PMU installation costs for the synchrophasor projects funded through the Recovery Act Smart Grid Programs. The data was compiled through interviews with the nine projects that deployed production grade synchrophasor systems. The study found that while the costs associated with PMUs as stand-alone

  2. Human Factors Engineering Analysis Tool - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Human Factors Engineering Analysis Tool Software tool that enables easy and quick selection of applicable regulatory guidelines as starting point for human factors engineering (HFE) analyses Savannah River National Laboratory Contact SRNL About This Technology Technology Marketing Summary A new software tool enables the easy and quick selection of applicable regulatory guidelines as a starting point for human factors engineering (HFE) analyses. Once selected, each guideline can be viewed on

  3. Test of factorization in diffractive deep inelastic scattering and

    Office of Scientific and Technical Information (OSTI)

    photoproduction at HERA (Journal Article) | SciTech Connect Test of factorization in diffractive deep inelastic scattering and photoproduction at HERA Citation Details In-Document Search Title: Test of factorization in diffractive deep inelastic scattering and photoproduction at HERA The QCD factorization theorem in diffraction is tested by comparing diffractive jet production data to QCD predictions based on fits to inclusive diffractive cross section data. H1 measured dijet production with

  4. Theory of factors limiting high gradient operation of warm accelerating

    Office of Scientific and Technical Information (OSTI)

    structures (Technical Report) | SciTech Connect Theory of factors limiting high gradient operation of warm accelerating structures Citation Details In-Document Search Title: Theory of factors limiting high gradient operation of warm accelerating structures This final report summarizes the research performed during the time period from 8/1/2010 to 7/31/2013. It consists of two parts describing our studies in two directions: (a) analysis of factors limiting operation of dielectric-loaded

  5. Major Risk Factors to the Integrated Facility Disposition Project |

    Energy Savers [EERE]

    Department of Energy to the Integrated Facility Disposition Project Major Risk Factors to the Integrated Facility Disposition Project The scope of the Integrated Facility Disposition Project (IFDP) needs to comprehensively address a wide range of environmental management risks at the Oak Ridge Reservation (ORO). PDF icon Major Risk Factors to the Integrated Facility Disposition Project More Documents & Publications Major Risk Factors Integrated Facility Disposition Project - Oak Ridge

  6. EPA Rainfall Erosivity Factor Calculator Website | Open Energy...

    Open Energy Info (EERE)

    Calculator Website Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: EPA Rainfall Erosivity Factor Calculator Website Abstract This website allows...

  7. Crystal structure of elongation factor 4 bound to a clockwise...

    Office of Scientific and Technical Information (OSTI)

    Search Title: Crystal structure of elongation factor 4 bound to a clockwise ratcheted ribosome Authors: Gagnon, Matthieu G. ; Lin, Jinzhong ; Bulkley, David ; Steitz, Thomas A. ...

  8. EPA - Rainfall Erosivity Factor Calculator webpage | Open Energy...

    Open Energy Info (EERE)

    Not Provided DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for EPA - Rainfall Erosivity Factor Calculator webpage Citation Environmental...

  9. QCD Factorization for heavy quarkonium production at collider...

    Office of Scientific and Technical Information (OSTI)

    Title: QCD Factorization for heavy quarkonium production at collider energies In this talk, I briefly review several models of the heavy quarkonium production at collider energies, ...

  10. Development of the Electricity Carbon Emission Factors for Russia...

    Open Energy Info (EERE)

    Russia Jump to: navigation, search Name Development of the Electricity Carbon Emission Factors for Russia AgencyCompany Organization European Bank for Reconstruction and...

  11. Factors Affecting HCCI Combustion Phasing for Fuels with Single...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Affecting HCCI Combustion Phasing for Fuels with Single- and Dual-Stage Chemistry Factors Affecting HCCI Combustion Phasing for Fuels with Single- and Dual-Stage Chemistry 2004 ...

  12. Analytical evaluation of atomic form factors: Application to Rayleigh scattering

    SciTech Connect (OSTI)

    Safari, L.; Santos, J. P.; Amaro, P.; Jänkälä, K.; Fratini, F.

    2015-05-15

    Atomic form factors are widely used for the characterization of targets and specimens, from crystallography to biology. By using recent mathematical results, here we derive an analytical expression for the atomic form factor within the independent particle model constructed from nonrelativistic screened hydrogenic wave functions. The range of validity of this analytical expression is checked by comparing the analytically obtained form factors with the ones obtained within the Hartee-Fock method. As an example, we apply our analytical expression for the atomic form factor to evaluate the differential cross section for Rayleigh scattering off neutral atoms.

  13. Factors Impacting EGR Cooler Fouling - Main Effects and Interactions...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Impacting EGR Cooler Fouling - Main Effects and Interactions Factors Impacting EGR Cooler Fouling - Main Effects and Interactions Presentation given at the 16th Directions in...

  14. Electromagnetic form factors and the hypercentral constituent quark model

    SciTech Connect (OSTI)

    Sanctis, M. De; Giannini, M. M.; Santopinto, E.; Vassallo, A.

    2007-12-15

    We present new results concerning the electromagnetic form factors of the nucleon using a relativistic version of the hypercentral constituent quark model and a relativistic current.

  15. Method for determining formation quality factor from well log...

    Office of Scientific and Technical Information (OSTI)

    well log data and its application to seismic reservoir characterization Citation Details In-Document Search Title: Method for determining formation quality factor from well log ...

  16. An extracytoplasmic function sigma factor-dependent periplasmic...

    Office of Scientific and Technical Information (OSTI)

    for survival and Shewanella harbors multiple ECF (extracytoplasmic function) genes and cognate anti-sigma factor genes. Here we comparatively analyzed two of the...

  17. Scaling factor inconsistencies in neutrinoless double beta decay

    SciTech Connect (OSTI)

    Cowell, S. [Theoretical Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

    2006-02-15

    The modern theory of neutrinoless double beta decay includes a scaling factor that has often been treated inconsistently in the literature. The nuclear contribution to the decay half-life can be suppressed by 15%-20% when scaling factors are mismatched. Correspondingly, is overestimated.

  18. Consideration of Factors Affecting Strip Effluent PH and Sodium Content

    SciTech Connect (OSTI)

    Peters, T.

    2015-07-29

    A number of factors were investigated to determine possible reasons for why the Strip Effluent (SE) can sometimes have higher than expected pH values and/or sodium content, both of which have prescribed limits. All of the factors likely have some impact on the pH values and Na content.

  19. Nuclear factor-?B is a common upstream signal for growth differentiation factor-5 expression in brown adipocytes exposed to pro-inflammatory cytokines and palmitate

    SciTech Connect (OSTI)

    Hinoi, Eiichi; Iezaki, Takashi; Ozaki, Kakeru; Yoneda, Yukio

    2014-10-03

    Highlights: • GDF5 expression is up-regulated by IL-1?, TNF-? and palmitate in brown pre-adipocytes. • NF-?B stimulates promoter activity and expression of GDF5 in brown pre-adipocytes. • Recruitment of NF-?B to the GDF5 promoter is facilitated in BAT from ob/ob mice. • An NF-?B inhibitor prevents upregulation of GDF5 expression in brown pre-adipocytes. - Abstract: We have previously demonstrated that genetic and acquired obesity similarly led to drastic upregulation in brown adipose tissue (BAT), rather than white adipose tissue, of expression of both mRNA and corresponding protein for the bone morphogenic protein/growth differentiation factor (GDF) member GDF5 capable of promoting brown adipogenesis. In this study, we evaluated expression profiles of GDF5 in cultured murine brown pre-adipocytes exposed to pro-inflammatory cytokines and free fatty acids (FFAs), which are all shown to play a role in the pathogenesis of obesity. Both interleukin-1? (IL-1?) and tumor necrosis factor-? (TNF-?) were effective in up-regulating GDF5 expression in a concentration-dependent manner, while similar upregulation was seen in cells exposed to the saturated FFA palmitate, but not to the unsaturated FFA oleate. In silico analysis revealed existence of the putative nuclear factor-?B (NF-?B) binding site in the 5?-flanking region of mouse GDF5, whereas introduction of NF-?B subunits drastically facilitated both promoter activity and expression of GDF5 in brown pre-adipocytes. Chromatin immunoprecipitation analysis confirmed significant facilitation of the recruitment of NF-?B to the GDF5 promoter in lysed extracts of BAT from leptin-deficient ob/ob obese mice. Upregulation o GDF5 expression was invariably inhibited by an NF-?B inhibitor in cultured brown pre-adipocytes exposed to IL-1?, TNF-? and palmitate. These results suggest that obesity leads to upregulation of GDF5 expression responsible for the promotion of brown adipogenesis through a mechanism relevant to activation of the NF-?B pathway in response to particular pro-inflammatory cytokines and/or saturated FFAs in BAT.

  20. H. R. 5904: A Bill to amend the Internal Revenue Code of 1986 to provide tax relief to utilities installing acid rain reduction equipment, introduced in the House of Representatives, One Hundred First Congress, Second Session, October 23, 1990

    SciTech Connect (OSTI)

    Not Available

    1990-01-01

    This bill was introduced into the US House of Representatives on October 23, 1990 to control acid rain. This legislation focuses on tax credit for equipment to meet acid rain reduction standards, as well as tax-exempt financing of acid rain control property. In addition, a tax credit is issued for minerals used to reduce the sulfur in coal.

  1. Lifestyle Factors in U.S. Residential Electricity Consumption

    SciTech Connect (OSTI)

    Sanquist, Thomas F.; Orr, Heather M.; Shui, Bin; Bittner, Alvah C.

    2012-03-30

    A multivariate statistical approach to lifestyle analysis of residential electricity consumption is described and illustrated. Factor analysis of selected variables from the 2005 U.S. Residential Energy Consumption Survey (RECS) identified five lifestyle factors reflecting social and behavioral choices associated with air conditioning, laundry usage, personal computer usage, climate zone of residence, and TV use. These factors were also estimated for 2001 RECS data. Multiple regression analysis using the lifestyle factors yields solutions accounting for approximately 40% of the variance in electricity consumption for both years. By adding the associated household and market characteristics of income, local electricity price and access to natural gas, variance accounted for is increased to approximately 54%. Income contributed only {approx}1% unique variance to the 2005 and 2001 models, indicating that lifestyle factors reflecting social and behavioral choices better account for consumption differences than income. This was not surprising given the 4-fold range of energy use at differing income levels. Geographic segmentation of factor scores is illustrated, and shows distinct clusters of consumption and lifestyle factors, particularly in suburban locations. The implications for tailored policy and planning interventions are discussed in relation to lifestyle issues.

  2. Model-independent plotting of the cosmological scale factor as a function of lookback time

    SciTech Connect (OSTI)

    Ringermacher, H. I.; Mead, L. R., E-mail: ringerha@gmail.com, E-mail: Lawrence.mead@usm.edu [Department of Physics and Astronomy, University of Southern Mississippi, Hattiesburg, MS 39406 (United States)

    2014-11-01

    In this work we describe a model-independent method of developing a plot of scale factor a(t) versus lookback time t{sub L} from the usual Hubble diagram of modulus data against redshift. This is the first plot of this type. We follow the model-independent methodology of Daly and Djorgovski used for their radio-galaxy data. Once the a(t)data plot is completed, any model can be applied and will display as described in the standard literature. We then compile an extensive data set to z = 1.8 by combining Type Ia supernovae (SNe Ia) data from SNLS3 of Conley et al., high-z SNe data of Riess et al., and radio-galaxy data of Daly and Djorgovski to validate the new plot. We first display these data on a standard Hubble diagram to confirm the best fit for ?CDM cosmology, and thus validate the joined data set. The scale factor plot is then developed from the data and the ?CDM model is again displayed from a least-squares fit. The fit parameters are in agreement with the Hubble diagram fit confirming the validity of the new plot. Of special interest is the transition time of the universe, which in the scale factor plot will appear as an inflection point in the data set. Noise is more visible in this presentation, which is particularly sensitive to inflection points of any model displayed in the plot, unlike on a modulus-z diagram, where there are no inflection points and the transition-z is not at all obvious by inspection. We obtain a lower limit of z ? 0.6. It is evident from this presentation that there is a dearth of SNe data in the range z = 1-2, exactly the range necessary to confirm a ?CDM transition-z around z = 0.76. We then compare a 'toy model' wherein dark matter is represented as a perfect fluid with an equation of state p = –(1/3) ? to demonstrate the plot sensitivity to model choice. Its density varies as 1/t {sup 2} and it enters the Friedmann equations as ?{sub dark}/t {sup 2}, replacing only the ?{sub dark}/a {sup 3} term. The toy model is a close match to ?CDM, but separates from it on the scale factor plot for similar ?CDM density parameters. It is described in the Appendix. A more complete transition time analysis will be presented in a future paper.

  3. Applying Human Factors Evaluation and Design Guidance to a Nuclear Power Plant Digital Control System

    SciTech Connect (OSTI)

    Thomas Ulrich; Ronald Boring; William Phoenix; Emily Dehority; Tim Whiting; Jonathan Morrell; Rhett Backstrom

    2012-08-01

    The United States (U.S.) nuclear industry, like similar process control industries, has moved toward upgrading its control rooms. The upgraded control rooms typically feature digital control system (DCS) displays embedded in the panels. These displays gather information from the system and represent that information on a single display surface. In this manner, the DCS combines many previously separate analog indicators and controls into a single digital display, whereby the operators can toggle between multiple windows to monitor and control different aspects of the plant. The design of the DCS depends on the function of the system it monitors, but revolves around presenting the information most germane to an operator at any point in time. DCSs require a carefully designed human system interface. This report centers on redesigning existing DCS displays for an example chemical volume control system (CVCS) at a U.S. nuclear power plant. The crucial nature of the CVCS, which controls coolant levels and boration in the primary system, requires a thorough human factors evaluation of its supporting DCS. The initial digital controls being developed for the DCSs tend to directly mimic the former analog controls. There are, however, unique operator interactions with a digital vs. analog interface, and the differences have not always been carefully factored in the translation of an analog interface to a replacement DCS. To ensure safety, efficiency, and usability of the emerging DCSs, a human factors usability evaluation was conducted on a CVCS DCS currently being used and refined at an existing U.S. nuclear power plant. Subject matter experts from process control engineering, software development, and human factors evaluated the DCS displays to document potential usability issues and propose design recommendations. The evaluation yielded 167 potential usability issues with the DCS. These issues should not be considered operator performance problems but rather opportunities identified by experts to improve upon the design of the DCS. A set of nine design recommendations was developed to address these potential issues. The design principles addressed the following areas: (1) color, (2) pop-up window structure, (3) navigation, (4) alarms, (5) process control diagram, (6) gestalt grouping, (7) typography, (8) terminology, and (9) data entry. Visuals illustrating the improved DCS displays accompany the design recommendations. These nine design principles serve as the starting point to a planned general DCS style guide that can be used across the U.S. nuclear industry to aid in the future design of effective DCS interfaces.

  4. Dual chain synthetic heparin-binding growth factor analogs

    DOE Patents [OSTI]

    Zamora, Paul O.; Pena, Louis A.; Lin, Xinhua

    2009-10-06

    The invention provides synthetic heparin-binding growth factor analogs having two peptide chains each branched from a branch moiety, such as trifunctional amino acid residues, the branch moieties separated by a first linker of from 3 to about 20 backbone atoms, which peptide chains bind a heparin-binding growth factor receptor and are covalently bound to a non-signaling peptide that includes a heparin-binding domain, preferably by a second linker, which may be a hydrophobic second linker. The synthetic heparin-binding growth factor analogs are useful as pharmaceutical agents, soluble biologics or as surface coatings for medical devices.

  5. Dual chain synthetic heparin-binding growth factor analogs

    DOE Patents [OSTI]

    Zamora, Paul O.; Pena, Louis A.; Lin, Xinhua

    2012-04-24

    The invention provides synthetic heparin-binding growth factor analogs having two peptide chains each branched from a branch moiety, such as trifunctional amino acid residues, the branch moieties separated by a first linker of from 3 to about 20 backbone atoms, which peptide chains bind a heparin-binding growth factor receptor and are covalently bound to a non-signaling peptide that includes a heparin-binding domain, preferably by a second linker, which may be a hydrophobic second linker. The synthetic heparin-binding growth factor analogs are useful as pharmaceutical agents, soluble biologics or as surface coatings for medical devices.

  6. The structure of the nucleon: Elastic electromagnetic form factors

    SciTech Connect (OSTI)

    Punjabi, V.; Perdrisat, C. F.; Jones, M. K.; Brash, E. J.; Carlson, C. E.

    2015-07-10

    Precise proton and neutron form factor measurements at Jefferson Lab, using spin observables, have recently made a significant contribution to the unraveling of the internal structure of the nucleon. Accurate experimental measurements of the nucleon form factors are a test-bed for understanding how the nucleon's static properties and dynamical behavior emerge from QCD, the theory of the strong interactions between quarks. There has been enormous theoretical progress, since the publication of the Jefferson Lab proton form factor ratio data, aiming at reevaluating the picture of the nucleon. We will review the experimental and theoretical developments in this field and discuss the outlook for the future.

  7. Property:Geothermal/LoadFactor | Open Energy Information

    Open Energy Info (EERE)

    to: navigation, search This is a property of type Number. Pages using the property "GeothermalLoadFactor" Showing 25 pages using this property. (previous 25) (next 25) 4 4 UR...

  8. Factors Controlling The Geochemical Evolution Of Fumarolic Encrustatio...

    Open Energy Info (EERE)

    Smokes (VTTS). The six-factor solution model explains a large proportion (low of 74% for Ni to high of 99% for Si) of the individual element data variance. Although the primary...

  9. CDPHE Construction Storm Water Forms R-Factor Waiver Application...

    Open Energy Info (EERE)

    CDPHE Construction Storm Water Forms R-Factor Waiver Application Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Permit ApplicationPermit...

  10. Phenomenology of semileptonic B -meson decays with form factors...

    Office of Scientific and Technical Information (OSTI)

    of semileptonic B -meson decays with form factors from lattice QCD Authors: Du, Daping ; El-Khadra, A. X. ; Gottlieb, Steven ; Kronfeld, A. S. ; Laiho, J. ; Lunghi, E. ; Van de...

  11. On the Consistency of QCBED Structure Factor Measurements for...

    Office of Scientific and Technical Information (OSTI)

    for bond-charge mapping. The standard deviation in the resulting distribution of derived X-ray structure factors is found to be an order of magnitude smaller than that in...

  12. Charm and bottom hadronic form factors with QCD sum rules

    SciTech Connect (OSTI)

    Bracco, M. E.; Rodrigues, B. O.; Cerqueira, A. Jr.

    2013-03-25

    We present a brief review of some calculations of form factors and coupling constants in vertices with charm and bottom mesons in the framework of QCD sum rules. We first discuss the motivation for this work, describing possible applications of these form factors to charm and bottom decays processes. We first make a summarize of the QCD sum rules method. We give special attention to the uncertainties of the method introducing by the intrinsic variation of the parameters. Finally we conclude.

  13. Article Published on LED Lumen Maintenance and Light Loss Factors

    Broader source: Energy.gov [DOE]

    An article has been published in LEUKOS: The Journal of the Illuminating Engineering Society of North America (IES) that may be of interest to the solid-state lighting community. Entitled "Lumen Maintenance and Light Loss Factors: Consequences of Current Design Practices for LEDs," the article was written by Michael Royer of Pacific Northwest National Laboratory and discusses complications related to the lamp lumen depreciation (LLD) light loss factor and LEDs.

  14. Nonrelativistic QCD factorization and the velocity dependence of NNLO poles

    Office of Scientific and Technical Information (OSTI)

    in heavy quarkonium production (Journal Article) | SciTech Connect Nonrelativistic QCD factorization and the velocity dependence of NNLO poles in heavy quarkonium production Citation Details In-Document Search Title: Nonrelativistic QCD factorization and the velocity dependence of NNLO poles in heavy quarkonium production We study the transition of a heavy quark pair from octet to singlet color configurations at next-to-next-to-leading order in heavy quarkonium production. We show that the

  15. Phenylimidazoles as Potent and Selective Inhibitors of Coagulation Factor

    Office of Scientific and Technical Information (OSTI)

    XIa with in Vivo Antithrombotic Activity (Journal Article) | SciTech Connect Phenylimidazoles as Potent and Selective Inhibitors of Coagulation Factor XIa with in Vivo Antithrombotic Activity Citation Details In-Document Search Title: Phenylimidazoles as Potent and Selective Inhibitors of Coagulation Factor XIa with in Vivo Antithrombotic Activity Authors: Hangeland, Jon J. ; Friends, Todd J. ; Rossi, Karen A. ; Smallheer, Joanne M. ; Wang, Cailan ; Sun, Zhong ; Corte, James R. ; Fang,

  16. Key factors for determining groundwater impacts due to leakage from

    Office of Scientific and Technical Information (OSTI)

    geologic carbon sequestration reservoirs (Journal Article) | SciTech Connect Journal Article: Key factors for determining groundwater impacts due to leakage from geologic carbon sequestration reservoirs Citation Details In-Document Search Title: Key factors for determining groundwater impacts due to leakage from geologic carbon sequestration reservoirs The National Risk Assessment Partnership (NRAP) is developing a science-based toolset for the analysis of potential impacts to groundwater

  17. Is the proton electromagnetic form factor modified in nuclei? (Conference)

    Office of Scientific and Technical Information (OSTI)

    | SciTech Connect SciTech Connect Search Results Conference: Is the proton electromagnetic form factor modified in nuclei? Citation Details In-Document Search Title: Is the proton electromagnetic form factor modified in nuclei? Guided by the recent experimental confirmation of the validity of the Effective Momentum Approximation (EMA) in quasi-elastic scattering off nuclei, we have re-examined the extraction of the Longitudinal and Transverse Response Functions in medium-weight and heavy

  18. Is the proton electromagnetic form factor modified in nuclei? (Conference)

    Office of Scientific and Technical Information (OSTI)

    | SciTech Connect Is the proton electromagnetic form factor modified in nuclei? Citation Details In-Document Search Title: Is the proton electromagnetic form factor modified in nuclei? × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit OSTI to utilize additional information resources in energy science and technology. A paper copy

  19. Structural basis for Tetrahymena telomerase processivity factor Teb1

    Office of Scientific and Technical Information (OSTI)

    binding to single-stranded telomeric-repeat DNA (Journal Article) | SciTech Connect SciTech Connect Search Results Journal Article: Structural basis for Tetrahymena telomerase processivity factor Teb1 binding to single-stranded telomeric-repeat DNA Citation Details In-Document Search Title: Structural basis for Tetrahymena telomerase processivity factor Teb1 binding to single-stranded telomeric-repeat DNA Authors: Zeng, Zhixiong ; Min, Bosun ; Huang, Jing ; Hong, Kyungah ; Yang, Yuting ;

  20. Classical strongly coupled quark-gluon plasma. V. Structure factors

    SciTech Connect (OSTI)

    Cho, Sungtae; Zahed, Ismail

    2010-10-15

    We show that the classical and strongly coupled quark-gluon plasma is characterized by a multiple of structure factors that obey generalized Orstein-Zernicke equations. We use the canonical partition function and its associated density functional to derive analytical equations for the density and charge monopole structure factors for arbitrary values of {Gamma}=V/K, the ratio of the mean potential to the Coulomb energy. The results are compared with SU(2) molecular dynamics simulations.

  1. Factors Impacting EGR Cooler Fouling - Main Effects and Interactions |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Impacting EGR Cooler Fouling - Main Effects and Interactions Factors Impacting EGR Cooler Fouling - Main Effects and Interactions Presentation given at the 16th Directions in Engine-Efficiency and Emissions Research (DEER) Conference in Detroit, MI, September 27-30, 2010. PDF icon deer10_styles.pdf More Documents & Publications Identification and Control of Factors that Affect EGR Cooler Fouling The Impact of PM and HC on EGR Cooler Fouling EGR Cooler Fouling -

  2. Structural basis of JAZ repression of MYC transcription factors in

    Office of Scientific and Technical Information (OSTI)

    jasmonate signalling (Journal Article) | SciTech Connect Structural basis of JAZ repression of MYC transcription factors in jasmonate signalling Citation Details In-Document Search Title: Structural basis of JAZ repression of MYC transcription factors in jasmonate signalling Authors: Zhang, Feng ; Yao, Jian ; Ke, Jiyuan ; Zhang, Li ; Lam, Vinh Q. ; Xin, Xiu-Fang ; Zhou, X. Edward ; Chen, Jian ; Brunzelle, Joseph ; Griffin, Patrick R. ; Zhou, Mingguo ; Xu, H. Eric ; Melcher, Karsten ; He ,

  3. Tetrahydroquinoline Derivatives as Potent and Selective Factor XIa

    Office of Scientific and Technical Information (OSTI)

    Inhibitors (Journal Article) | SciTech Connect Tetrahydroquinoline Derivatives as Potent and Selective Factor XIa Inhibitors Citation Details In-Document Search Title: Tetrahydroquinoline Derivatives as Potent and Selective Factor XIa Inhibitors Authors: Quan, Mimi L. ; Wong, Pancras C. ; Wang, Cailan ; Woerner, Francis ; Smallheer, Joanne M. ; Barbera, Frank A. ; Bozarth, Jeffrey M. ; Brown, Randi L. ; Harpel, Mark R. ; Luettgen, Joseph M. ; Morin, Paul E. ; Peterson, Tara ; Ramamurthy,

  4. Constructing the S-matrix With Complex Factorization

    SciTech Connect (OSTI)

    Schuster, Philip C.; Toro, Natalia; /Stanford U., ITP

    2009-06-19

    A remarkable connection between BCFW recursion relations and constraints on the S-matrix was made by Benincasa and Cachazo in 0705.4305, who noted that mutual consistency of different BCFW constructions of four-particle amplitudes generates nontrivial (but familiar) constraints on three-particle coupling constants - these include gauge invariance, the equivalence principle, and the lack of non-trivial couplings for spins > 2. These constraints can also be derived with weaker assumptions, by demanding the existence of four-point amplitudes that factorize properly in all unitarity limits with complex momenta. From this starting point, we show that the BCFW prescription can be interpreted as an algorithm for fully constructing a tree-level S-matrix, and that complex factorization of general BCFW amplitudes follows from the factorization of four-particle amplitudes. The allowed set of BCFW deformations is identified, formulated entirely as a statement on the three-particle sector, and using only complex factorization as a guide. Consequently, our analysis based on the physical consistency of the S-matrix is entirely independent of field theory. We analyze the case of pure Yang-Mills, and outline a proof for gravity. For Yang-Mills, we also show that the well-known scaling behavior of BCFW-deformed amplitudes at large z is a simple consequence of factorization. For gravity, factorization in certain channels requires asymptotic behavior {approx} 1/z{sup 2}.

  5. Landscape Characterization and Representativeness Analysis for...

    Office of Scientific and Technical Information (OSTI)

    Number: DE-AC05-00OR22725 Resource Type: Dataset Data Type: Numeric Data Research Org: Climate Change Science Institute (CCSI), Oak Ridge National Laboratory (ORNL), Oak Rdige,...

  6. Drop Testing Representative Multi-Canister Overpacks

    SciTech Connect (OSTI)

    Snow, Spencer D.; Morton, Dana K.

    2015-06-01

    The objective of the work reported herein was to determine the ability of the Multi- Canister Overpack (MCO) canister design to maintain its containment boundary after an accidental drop event. Two test MCO canisters were assembled at Hanford, prepared for testing at the Idaho National Engineering and Environmental Laboratory (INEEL), drop tested at Sandia National Laboratories, and evaluated back at the INEEL. In addition to the actual testing efforts, finite element plastic analysis techniques were used to make both pre-test and post-test predictions of the test MCOs structural deformations. The completed effort has demonstrated that the canister design is capable of maintaining a 50 psig pressure boundary after drop testing. Based on helium leak testing methods, one test MCO was determined to have a leakage rate not greater than 1x10-5 std cc/sec (prior internal helium presence prevented a more rigorous test) and the remaining test MCO had a measured leakage rate less than 1x10-7 std cc/sec (i.e., a leaktight containment) after the drop test. The effort has also demonstrated the capability of finite element methods using plastic analysis techniques to accurately predict the structural deformations of canisters subjected to an accidental drop event.

  7. Facility Representative Qualification Equivalencies Based on...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    been revised several times. The purpose of this Memorandum is to provide guidance, Attachment 1, to Qualifying Officials (QO) on how to use the cross-walk, Attachment 2, in...

  8. 1997 Annual Facility Representative Workshop Attendees

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Kellar Ken HQ DP-45 (301) 903-8046 kenneth.kellar@dp.doe.gov Kozak Pete SR TRITIUM ... Wade Ken RL TANKS (509) 373-9961 kennethgwade@rl.gov Woodworth Marc SR RSFD ...

  9. 1998 Annual Facility Representative Workshop Attendees

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... (303) 966-7954 (303) 966-8389 brad.ring@rfets.gov Robbins Teresa RF SNMPu (303) 966-3525 (303) 966-5248 teresa.robbins@rfets.gov Robin Ron AL LAAO (505) 667-4548 (505) ...

  10. Arkansas Converter Station Alternative Siting Area Representative...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... ALEX H MUSE LUCIAS E. MEEMAN-SHELBY FOREST Side Park Brunetti Park City Park Brunetti Park John Robbins Field East Hill Park Deermont Park Gaisman Park Elmore Park Rockyford Park ...

  11. Advisory Board Seats New Student Representatives | Department...

    Office of Environmental Management (EM)

    Honor Society, and she is involved with Project U, a club that stands against bullying. She is on the girls' powderpuff football team, and in her free time, she enjoys...

  12. Advisory Board Seats New Student Representatives | Department...

    Office of Environmental Management (EM)

    the Hardin Valley varsity tennis team the past three years. Sophia is interested in medicine and health sciences and is thinking about a career in medicine. She is currently the...

  13. DOE ORP Contracting Officer Representatives - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Carosino 02102010 BNI DE-AC2701RV14136 Bill Hamel 02052013 BNI DE-AC2701RV14136 Ben Harp 07272012 BNI DE-AC2701RV14136 Delmar Noyes 07272012 BNI DE-AC2701RV14136 Gary Olsen...

  14. Understanding and representing natural language meaning

    SciTech Connect (OSTI)

    Waltz, D.L.; Maran, L.R.; Dorfman, M.H.; Dinitz, R.; Farwell, D.

    1982-12-01

    During this contract period the authors have: (a) continued investigation of events and actions by means of representation schemes called 'event shape diagrams'; (b) written a parsing program which selects appropriate word and sentence meanings by a parallel process known as activation and inhibition; (c) begun investigation of the point of a story or event by modeling the motivations and emotional behaviors of story characters; (d) started work on combining and translating two machine-readable dictionaries into a lexicon and knowledge base which will form an integral part of our natural language understanding programs; (e) made substantial progress toward a general model for the representation of cognitive relations by comparing English scene and event descriptions with similar descriptions in other languages; (f) constructed a general model for the representation of tense and aspect of verbs; (g) made progress toward the design of an integrated robotics system which accepts English requests, and uses visual and tactile inputs in making decisions and learning new tasks.

  15. Hazardous-waste cleanup and enforcement problems: Indiana. Hearing before the Subcommittee of the Committee on Government Operations, House of Representatives, Ninety-Seventh Congress, Second Session, June 1, 1982

    SciTech Connect (OSTI)

    Not Available

    1982-01-01

    Thirteen witnesses representing the private and public sectors testified at a Seymour, Indiana hearing on hazardous materials at the Seymour Recycling facility and efforts to clean up the site. The facility began operations in 1968, and was closed down in February of 1980; the Environmental Protection Agency (EPA) had discovered during 1978 that the company was not disposing of its chemical wastes properly. Local concerns focused on why the EPA efforts slowed noticeably in the spring of 1981 and whether the site qualifies for superfund financing. Spokesmen from EPA argued that the slowdown was due to inaction at the state level, but state representatives countered that the problem was a lack of state funds to match federal funding. Other witnesses pursued health and safety issues and the efforts Seymour citizens have made to gain relief. (DCK)

  16. Crystal structure of enterococcus faecalis sly A-like transcriptional factor.

    SciTech Connect (OSTI)

    Wu, R.; Zhang, R.; Zagnitko, O.; Dementieva, I.; Maltsev, N.; Watson, J. D.; Laskowski, R.; Gornicki, P.; Joachimiak, A.; Univ. of Chicago; European Bioinformatics Inst.

    2003-05-30

    The crystal structure of a SlyA transcriptional regulator at 1.6 {angstrom} resolution is presented, and structural relationships between members of the MarR/SlyA family are discussed. The SlyA family, which includes SlyA, Rap, Hor, and RovA proteins, is widely distributed in bacterial and archaeal genomes. Current evidence suggests that SlyA-like factors act as repressors, activators, and modulators of gene transcription. These proteins have been shown to up-regulate the expression of molecular chaperones, acid-resistance proteins, and cytolysin, and down-regulate several biosynthetic enzymes. The structure of SlyA from Enterococcus faecalis, determined as a part of an ongoing structural genomics initiative (www.mcsg.anl.gov), revealed the same winged helix DNA-binding motif that was recently found in the MarR repressor from Escherichia coli and the MexR repressor from Pseudomonas aeruginosa, a sequence homologue of MarR. Phylogenetic analysis of the MarR/SlyA family suggests that Sly is placed between the SlyA and MarR subfamilies and shows significant sequence similarity to members of both subfamilies.

  17. Identification and Evaluation of Human Factors Issues Associated with Emerging Nuclear Plant Technology

    SciTech Connect (OSTI)

    O'Hara,J.M.; Higgins,J.; Brown, William S.

    2009-04-01

    This study has identified human performance research issues associated with the implementation of new technology in nuclear power plants (NPPs). To identify the research issues, current industry developments and trends were evaluated in the areas of reactor technology, instrumentation and control technology, human-system integration technology, and human factors engineering (HFE) methods and tools. The issues were prioritized into four categories based on evaluations provided by 14 independent subject matter experts representing vendors, utilities, research organizations and regulators. Twenty issues were categorized into the top priority category. The study also identifies the priority of each issue and the rationale for those in the top priority category. The top priority issues were then organized into research program areas of: New Concepts of Operation using Multi-agent Teams, Human-system Interface Design, Complexity Issues in Advanced Systems, Operating Experience of New and Modernized Plants, and HFE Methods and Tools. The results can serve as input to the development of a long-term strategy and plan for addressing human performance in these areas to support the safe operation of new NPPs.

  18. The dynamic shape factor of sodium chloride nanoparticles as regulated by drying rate

    SciTech Connect (OSTI)

    Wang, Z.; Lewis, E.; King, S. M.; Freney, E.; Rosenoern, T.; Smith, M.; Chen, Q.; Kuwata, M.; Poschl, U.; Wang, W.; Buseck, P. R.; Martin, S. T.

    2010-09-01

    The influence of drying rate on the dynamic shape factor {chi} of NaCl particles was investigated. The drying rate at the efflorescence relative humidity (ERH) of 45% was controlled in a laminar flow tube and varied from 5.5 {+-} 0.9 to 101 {+-} 3 RH s{sup -1} at ERH, where RH represents one percent unit of relative humidity. Dry particles having mobility diameters of 23-84 nm were studied, corresponding to aqueous particles of 37-129 nm at the RH (57%) prior to drying. At each mobility diameter and drying rate, the critical supersaturation of cloud-condensation activation was also measured. The mobility diameter and the critical supersaturation were combined in an analysis to determine the value of {chi}. The measured values varied from 1.02 to 1.26. For fixed particle diameter the {chi} value decreased with increasing drying rate. For fixed drying rate, a maximum occurred in {chi} between 35- and 40-nm dry mobility diameter, with a lower {chi} for both smaller and larger particles. The results of this study, in conjunction with the introduced apparatus for obtaining quantified drying rates, can allow the continued development of a more detailed understanding of the morphology of submicron salt particles, with the potential for the follow-on development of quantitative modeling of evaporation and crystal growth at these dimensions.

  19. Human factors design, verification, and validation for two types of control room upgrades at a nuclear power plant

    SciTech Connect (OSTI)

    Boring, Laurids Ronald

    2014-10-01

    This paper describes the NUREG-0711 based human factors engineering (HFE) phases and associated elements required to support design, verification and validation (V&V), and implementation of a new plant process computer (PPC) and turbine control system (TCS) at a representative nuclear power plant. This paper reviews ways to take a human-system interface (HSI) specification and use it when migrating legacy PPC displays or designing displays with new functionality. These displays undergo iterative usability testing during the design phase and then undergo an integrated system validation (ISV) in a full scope control room training simulator. Following the successful demonstration of operator performance with the systems during the ISV, the new system is implemented at the plant, first in the training simulator and then in the main control room.

  20. Observation of the fundamental Nyquist noise limit in an ultra-high Q-factor cryogenic bulk acoustic wave cavity

    SciTech Connect (OSTI)

    Goryachev, Maxim Ivanov, Eugene N.; Tobar, Michael E.; Kann, Frank van; Galliou, Serge

    2014-10-13

    Thermal Nyquist noise fluctuations of high-Q bulk acoustic wave cavities have been observed at cryogenic temperatures with a DC superconducting quantum interference device amplifier. High Q modes with bandwidths of few tens of milliHz produce thermal fluctuations with a signal-to-noise ratio of up to 23?dB. The estimated effective temperature from the Nyquist noise is in good agreement with the physical temperature of the device, confirming the validity of the equivalent circuit model and the non-existence of any excess resonator self-noise. The measurements also confirm that the quality factor remains extremely high (Q?>?10{sup 8} at low order overtones) for very weak (thermal) system motion at low temperatures, when compared to values measured with relatively strong external excitation. This result represents an enabling step towards operating such a high-Q acoustic device at the standard quantum limit.

  1. Factors controlling physico-chemical characteristics in the coastal waters off Mangalore-A multivariate approach

    SciTech Connect (OSTI)

    Shirodkar, P.V. Mesquita, A.; Pradhan, U.K.; Verlekar, X.N.; Babu, M.T.; Vethamony, P.

    2009-04-15

    Water quality parameters (temperature, pH, salinity, DO, BOD, suspended solids, nutrients, PHc, phenols, trace metals-Pb, Cd and Hg, chlorophyll-a (chl-a) and phaeopigments) and the sediment quality parameters (total phosphorous, total nitrogen, organic carbon and trace metals) were analysed from samples collected at 15 stations along 3 transects off Karnataka coast (Mangalore harbour in the south to Suratkal in the north), west coast of India during 2007. The analyses showed high ammonia off Suratkal, high nitrite (NO{sub 2}-N) and nitrate (NO{sub 3}-N) in the nearshore waters off Kulai and high nitrite (NO{sub 2}-N) and ammonia (NH{sub 3}-N) in the harbour area. Similarly, high petroleum hydrocarbon (PHc) values were observed near the harbour, while phenols remained high in the nearshore waters of Kulai and Suratkal. Significantly, high concentrations of cadmium and mercury with respect to the earlier studies were observed off Kulai and harbour regions, respectively. R-mode varimax factor analyses were applied separately to surface and bottom water data sets due to existing stratification in the water column caused by riverine inflow and to sediment data. This helped to understand the interrelationships between the variables and to identify probable source components for explaining the environmental status of the area. Six factors (each for surface and bottom waters) were found responsible for variance (86.9% in surface and 82.4% in bottom) in the coastal waters between Mangalore and Suratkal. In sediments, 4 factors explained 86.8% of the observed total variance. The variances indicated addition of nutrients and suspended solids to the coastal waters due to weathering and riverine transport and are categorized as natural sources. The observed contamination of coastal waters indicated anthropogenic inputs of Cd and phenol from industrial effluent sources at Kulai and Suratkal, ammonia from wastewater discharges off Kulai and harbour, PHc and Hg from boat traffic and harbour activities of New Mangalore harbour. However, the strong seasonal currents and the seasonal winds keep the coastal waters well mixed and aerated, which help to disperse the contaminants, without significantly affecting chlorophyll-a concentrations. The interrelationship between the stations as shown by cluster analyses and depicted in dendograms, categorize the contamination levels sector-wise.

  2. Cosmic Reionization On Computers III. The Clumping Factor

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Kaurov, Alexander A.; Gnedin, Nickolay Y.

    2015-09-09

    We use fully self-consistent numerical simulations of cosmic reionization, completed under the Cosmic Reionization On Computers project, to explore how well the recombinations in the ionized intergalactic medium (IGM) can be quantified by the effective "clumping factor." The density distribution in the simulations (and, presumably, in a real universe) is highly inhomogeneous and more-or-less smoothly varying in space. However, even in highly complex and dynamic environments, the concept of the IGM remains reasonably well-defined; the largest ambiguity comes from the unvirialized regions around galaxies that are over-ionized by the local enhancement in the radiation field ("proximity zones"). This ambiguity precludesmore » computing the IGM clumping factor to better than about 20%. Furthermore, we discuss a "local clumping factor," defined over a particular spatial scale, and quantify its scatter on a given scale and its variation as a function of scale.« less

  3. The structure of the nucleon: Elastic electromagnetic form factors

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Punjabi, V.; Perdrisat, C. F.; Jones, M. K.; Brash, E. J.; Carlson, C. E.

    2015-07-10

    Precise proton and neutron form factor measurements at Jefferson Lab, using spin observables, have recently made a significant contribution to the unraveling of the internal structure of the nucleon. Accurate experimental measurements of the nucleon form factors are a test-bed for understanding how the nucleon's static properties and dynamical behavior emerge from QCD, the theory of the strong interactions between quarks. There has been enormous theoretical progress, since the publication of the Jefferson Lab proton form factor ratio data, aiming at reevaluating the picture of the nucleon. We will review the experimental and theoretical developments in this field and discussmore » the outlook for the future.« less

  4. OPERATIONAL AND COMPOSITIONAL FACTORS THAT AFFECT THE PERFORMANCE PROPERTIES OF ARP/MCU SALTSTONE GROUT

    SciTech Connect (OSTI)

    Reigel, M.; Edwards, T.; Pickenheim, B.

    2012-02-15

    The Saltstone Production Facility (SPF) receives low level waste (LLW) salt solution from Tank 50H for treatment and disposal. Tank 50H receives transfers from the Effluent Treatment Project (ETP), the H-Canyon General Purpose Evaporator, and the Actinide Removal Process/Modular Caustic Side Solvent Extraction Unit (ARP/MCU) Decontaminated Salt Solution Hold Tank (DSS-HT). At the SPF, the LLW is mixed with premix (a cementitious mixture of portland cement (PC), blast furnace slag (BFS) and Class F fly ash (FA)) in a Readco mixer to produce fresh (uncured) saltstone that is transferred to the Saltstone Disposal Facility (SDF) vaults. The saltstone formulation (mix design) must produce a grout waste form that meets both placement and performance properties. In previous simulated saltstone studies, multiple compositional factors were identified that drive the performance properties of saltstone made from the projected ARP/MCU salt solution. This composition was selected as salt solution simulant since ARP/MCU is the primary influent into Tank 50H. The primary performance property investigated was hydraulic conductivity since it is a variable input property to the saltstone Performance Assessment (PA) transport model. In addition, the porosity, also referred to as void structure, is another variable that impacts the PA response. In addition, Young's modulus and cured density are other performance properties analyzed in this report; however they are indicators of the performance of saltstone and not direct inputs into the PA. The data from previous studies showed that the largest impact on the performance properties of saltstone was due to curing temperature, followed by aluminate concentration in the salt solution, water to premix ratio and premix composition. However, due to the scope of the previous studies, only a few mixes were cured and analyzed at higher temperatures. The samples cured at 60 C had an increased hydraulic conductivity of approximately 600 times that of the sample cured at room temperature. The hydration reactions initiated during the mixing of the premix and salt solution continue during the curing period in the vaults to produce the hardened waste form product. The heat generated from exothermic hydration reactions results in a temperature increase in the vaults that depends on the composition of the decontaminated salt solution being dispositioned, the grout formulation (mix design) and the pour frequency and volume. This heat generation is a contributing factor to the temperature increase in the vaults that leads to an increased cure temperature for the grout. This report will further investigate the impact of curing temperature on saltstone performance properties (hydraulic conductivity, Young's modulus, porosity, etc.) over a range of aluminate concentration, water to premix (w/p) ratio and weight percent fly ash in the premix processed at the SPF. The three curing temperatures selected for this study were chosen to provide data at fixed cure temperatures that represent measured temperatures in the SDF vaults. This does not represent the conditions in the vault where the temperature of the saltstone is continually changing with time. For example, it may take several days for the saltstone to reach 60 C at a given elevation. Previous results demonstrated that the rates at which a selected curing temperature is reached affect the performance properties. The approach taken in this task, a rapid increase to the curing temperature, may be conservative with respect to decreased performance. Nevertheless, the data will provide a basis from which to determine the impact of curing temperature on saltstone performance as a function of key variables. A statistical evaluation of the results for these mixes will be performed to provide the range, and associated uncertainties, of hydraulic conductivity and other properties over this factor space.

  5. Factors Affecting Power Output by Photovoltaic Cells Lesson

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Suzanne McClung Unit Title: Option C: Energy Subject: Chemistry Lesson Title: Factors Affecting Power Output by Photovoltaic Cells Grade Level(s): IB 2 (Senior - 3 rd year of chemistry) Lesson Length: 2-90 minute blocks with 30 minutes for wrap up in a 3 rd class period Date(s): * Learning Goals o Students will make observations of voltage and current in a solar panel system o Students will calculate power of a solar panel system o Students will determine the effect of a factor on the power

  6. Greybody factors for Myers–Perry black holes

    SciTech Connect (OSTI)

    Boonserm, Petarpa; Chatrabhuti, Auttakit Ngampitipan, Tritos; Visser, Matt

    2014-11-15

    The Myers–Perry black holes are higher-dimensional generalizations of the usual (3+1)-dimensional rotating Kerr black hole. They are of considerable interest in Kaluza–Klein models, specifically within the context of brane-world versions thereof. In the present article, we shall consider the greybody factors associated with scalar field excitations of the Myers–Perry spacetimes, and develop some rigorous bounds on these greybody factors. These bounds are of relevance for characterizing both the higher-dimensional Hawking radiation, and the super-radiance, that is expected for these spacetimes.

  7. Critical Factors Driving the High Volumetric Uptake of Methane in

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Cu-3(btc)(2) | Center for Gas SeparationsRelevant to Clean Energy Technologies | Blandine Jerome Critical Factors Driving the High Volumetric Uptake of Methane in Cu-3(btc)(2) Previous Next List Hulvey, Zeric; Vlaisavljevich, Bess; Mason, Jarad A.; Tsivion, Ehud; Dougherty, Timothy P.; Bloch, Eric D.; Head-Gordon, Martin; Smit, Berend; Long, Jeffrey R.; Brown, Craig M. Critical Factors Driving the High Volumetric Uptake of Methane in Cu-3(btc)(2). J. Amer. Chem. Soc., 137, 10816-10825

  8. Astrophysical S-factor for the radiative-capture reaction p{sup 13}C {yields} {sup 14}N{gamma}

    SciTech Connect (OSTI)

    Dubovichenko, S. B.

    2012-02-15

    The possibility of describing experimental data on the astrophysical S factor for radiative proton capture on a {sup 13}C nucleus at energies in the range 0.03-0.8 MeV is considered within the potential cluster model involving forbidden states. It is shown that the energy dependence of this astrophysical S factor can be reasonably explained on the basis of the E1 transition to the {sup 3}P{sub 1}-wave bound state of the {sup 14}N nucleus in the p{sup 13}C channel from the {sup 3}S{sub 1} wave of p{sup 13}C scattering in the resonance energy region around 0.55 MeV in the laboratory frame.

  9. High-speed rail transportation. Hearing before the Subcommittee on Transportation and Hazardous Materials of the Committee on Energy and Commerce, US House of Representatives, One Hundred Second Congress, First Session, October 16, 1991

    SciTech Connect (OSTI)

    Not Available

    1991-01-01

    H.R. 1087 would authorize a high speed rail transportation development and commercialization program, establish a national high speed rail transportation policy, and promote development and commercialization of high speed rail transportation by providing Federal guarantees of certain investments in high speed rail transportation facilities. Testimony was heard from representatives of MAGLEV USA, Federal Railroad Administration, National Railroad Passenger Corporation (Amtrak), the Office of Technology Assessment, MAGLEV, Inc., National Maglev Initiative, High Speed Rail Association, and the Texas High-Speed Rail Association. Additional information was supplied by the Coalition of Northeastern Governors, Republic Locomotive, Washington State High Speed Ground Transportation, and the Texas High Speed Authority.

  10. Issues relating to overlapping Federal and state responsibilities for the oversight of the Surface Mining Law. Hearing before a Subcommittee of the Committee on Government Operations, House of Representatives, One Hundredth Congress, First Session, October 26, 1987

    SciTech Connect (OSTI)

    Not Available

    1988-01-01

    The hearing was called regarding the responsibilities of the state and Federal government in administering the Federal Surface Mining Control and Reclamation Act of 1977. With mining taking place in 27 states under a variety of conditions and practices, the Act encourages the states to assume primacy responsibility for regulating coal mining. Once a state's plan is approved, the Federal role becomes one of oversight. This hearing examines Pennsylvania's programs and what happens when there is a disagreement between state and Federal authorities. Testimony is presented from 12 witnesses, representing coal companies, electric power companies, Sierra Club, National Wildlife Federation, Pennsylvania Department of Environmental Resources, and West Virginia.

  11. Tenth anniversary of the Surface Mining Control and Reclamation Act of 1977. Oversight hearing before the Subcommittee on Energy and the Environment of the Committee on Interior and Insular Affairs, House of Representatives, One Hundredth Congress, First Session

    SciTech Connect (OSTI)

    Not Available

    1988-01-01

    Testimony was heard from representatives from the Society of American Archeology, the Office of Surface Mining and Reclamation Enforcement, the Office of Environmental Energy Management of Pennsylvania, National Wildlife Federation, Sierra Club, Western Organizations of Resource Councils, Southwest Research and Information Center, West Virginia Highlands Conservancy, Illinois South Project, Concern About Water Loss Due to Mining, Mountain Stream Monitors, Citizens Organized Against Longwalling, Environmental Policy Institute, Kentucky Fair Tax Coalition, Save Our Cumberland Mountains, Navajo Nation, several coal mining companies, the National Coal Association, and Small Coal Operator Advisory Council. Prepared statements from all witnesses plus additional materials are included.

  12. H. R. 3052: This Act may be cited as the Coal Field Water Protection and Replacement Act, introduced in the US House of Representatives, One Hundred Second Congress, First Session, July 25, 1991

    SciTech Connect (OSTI)

    Not Available

    1991-01-01

    This bill would amend the Surface Mining Control and Reclamation Act of 1977 to provide for the protection of water resources during coal mining operations. Sections of the bill describe probable hydrologic consequences; surface and ground water monitoring plan; performance bonds; protection of water resources for permit approval; effect of underground coal mining operations; inspection and monitoring; penalty for failure of representative of Secretary or state regulatory authority to carry out certain duties; release of performance bond; water rights and replacement; regulations; and state programs.

  13. H. R. 2670: A bill to amend the Solid Waste Disposal Act to regulate ash from municipal solid waste incinerators as a hazardous waste, introduced in the US House of Representatives, One Hundred Second Congress, First Session, June 18, 1991

    SciTech Connect (OSTI)

    Not Available

    1991-01-01

    This bill was introduced into the US House of Representatives on June 18, 1991 to amend the Solid Waste disposal Act to regulate ash from municipal solid waste incinerators as a hazardous waste. When garbage is burned, toxic materials are concentrated in the ash. If the ash is disposed of in a landfill, these toxic materials can contaminate the ground water or surface water by leaching toxic materials from the ash. In addition, disposing of contaminated ash improperly can pose a health hazard. New authority is provided for regulating incinerator ash as a hazardous waste.

  14. UPDATING THE NRC GUIDANCE FOR HUMAN FACTORS ENGINEERING REVIEWS.

    SciTech Connect (OSTI)

    O HARA,J.M.; BROWN,W.S.; HIGGINS,J.C.; PERSENSKY,J.J.; LEWIS,P.M.; BONGARRA,J.

    2002-09-15

    The U.S. Nuclear Regulatory Commission (NRC) reviews the human factors engineering (HFE) aspects of nuclear plants. NUREG-0800 (Standard Review Plan), Chapter 18, ''Human Factors Engineering,'' is the principal NRC staff guidance document. Two main documents provide the review criteria to support the evaluations. The HFE Program Review Model (NUREG-0711) addresses the design process from planning to verification and validation to design implementation. The Human-System Interface Design Review Guidelines (NUREG-0700) provides the guidelines for the review of the HFE aspects of human-system interface technology, such as alarms, information systems, controls, and control room design. Since these documents were published in 1994 and 1996 respectively, they have been used by NRC staff, contractors, nuclear industry organizations, as well as by numerous organizations outside the nuclear industry. Using feedback from users and NRC research conducted in recent years, both documents have been revised and updated. This was done to ensure that they remain state-of-the-art evaluation tools for changing nuclear industry issues and emerging technologies. This paper describes the methodology used to revise and update the documents and summarizes the changes made to each and their current contents. Index Terms for this report are: Control system human factors, Ergonomics, Human factors, Nuclear power generation safety.

  15. Human Factors Evaluation of Advanced Electric Power Grid Visualization Tools

    SciTech Connect (OSTI)

    Greitzer, Frank L.; Dauenhauer, Peter M.; Wierks, Tamara G.; Podmore, Robin

    2009-04-01

    This report describes initial human factors evaluation of four visualization tools (Graphical Contingency Analysis, Force Directed Graphs, Phasor State Estimator and Mode Meter/ Mode Shapes) developed by PNNL, and proposed test plans that may be implemented to evaluate their utility in scenario-based experiments.

  16. The Modern description of semileptonic meson form factors

    SciTech Connect (OSTI)

    Hill, Richard J.

    2006-06-01

    I describe recent advances in our understanding of the hadronic form factors governing semileptonic meson transitions. The resulting framework provides a systematic approach to the experimental data, as a means of extracting precision observables, testing nonperturbative field theory methods, and probing a poorly understood limit of QCD.

  17. Nucleon form factors program with SBS at JLAB

    SciTech Connect (OSTI)

    Wojtsekhowski, Bogdan B.

    2014-12-01

    The physics of the nucleon form factors is the basic part of the Jefferson Laboratory program. We review the achievements of the 6-GeV era and the program with the 12- GeV beam with the SBS spectrometer in Hall A, with a focus on the nucleon ground state properties.

  18. Effect of Environmental Factors on Sulfur Gas Emissions from Drywall

    SciTech Connect (OSTI)

    Maddalena, Randy

    2011-08-20

    Problem drywall installed in U.S. homes is suspected of being a source of odorous and potentially corrosive indoor pollutants. The U.S. Consumer Product Safety Commission's (CPSC) investigation of problem drywall incorporates three parallel tracks: (1) evaluating the relationship between the drywall and reported health symptoms; (2) evaluating the relationship between the drywall and electrical and fire safety issues in affected homes; and (3) tracing the origin and the distribution of the drywall. To assess the potential impact on human health and to support testing for electrical and fire safety, the CPSC has initiated a series of laboratory tests that provide elemental characterization of drywall, characterization of chemical emissions, and in-home air sampling. The chemical emission testing was conducted at Lawrence Berkeley National Laboratory (LBNL). The LBNL study consisted of two phases. In Phase 1 of this study, LBNL tested thirty drywall samples provided by CPSC and reported standard emission factors for volatile organic compounds (VOCs), aldehydes, reactive sulfur gases (RSGs) and volatile sulfur compounds (VSCs). The standard emission factors were determined using small (10.75 liter) dynamic test chambers housed in a constant temperature environmental chamber. The tests were all run at 25 C, 50% relative humidity (RH) and with an area-specific ventilation rate of {approx}1.5 cubic meters per square meter of emitting surface per hour [m{sup 3}/m{sup 2}/h]. The thirty samples that were tested in Phase 1 included seventeen that were manufactured in China in 2005, 2006 and 2009, and thirteen that were manufactured in North America in 2009. The measured emission factors for VOCs and aldehydes were generally low and did not differ significantly between the Chinese and North American drywall. Eight of the samples tested had elevated emissions of volatile sulfur-containing compounds with total RSG emission factors between 32 and 258 micrograms per square meter per hour [{micro}g/m{sup 2}/h]. The dominant sulfur containing compounds in the RSG emission stream were hydrogen sulfide with emission factors between 17-201 {micro}g/m{sup 2}/h, and sulfur dioxide with emission factors between 8-64 {micro}g/m{sup 2}/h. The four highest emitting samples also had a unique signature of VSC emissions including > 40 higher molecular weight sulfur-containing compounds although the emission rate for the VSCs was several orders of magnitude lower than that of the RSGs. All of the high emitting drywall samples were manufactured in China in 2005-2006. Results from Phase 1 provided baseline emission factors for drywall samples manufactured in China and in North America but the results exclude variations in environmental conditions that may exist in homes or other built structures, including various combinations of temperature, RH, ventilation rate and the influence of coatings such as texture and paints. The objective of Phase 2 was to quantify the effect of temperature and RH on the RSG emission factors for uncoated drywall, and to measure the effect of plaster and paint coatings on RSG emission factors from drywall. Additional experiments were also performed to assess the influence of ventilation rate on measured emission factors for drywall.

  19. Experimental investigation of factors limiting slow axis beam quality in 9xx nm high power broad area diode lasers

    SciTech Connect (OSTI)

    Winterfeldt, M. Crump, P.; Wenzel, H.; Erbert, G.; Tränkle, G.

    2014-08-14

    GaAs-based broad-area diode lasers are needed with improved lateral beam parameter product (BPP{sub lat}) at high power. An experimental study of the factors limiting BPP{sub lat} is therefore presented, using extreme double-asymmetric (EDAS) vertical structures emitting at 910?nm. Continuous wave, pulsed and polarization-resolved measurements are presented and compared to thermal simulation. The importance of thermal and packaging-induced effects is determined by comparing junction -up and -down devices. Process factors are clarified by comparing diodes with and without index-guiding trenches. We show that in all cases studied, BPP{sub lat} is limited by a non-thermal BPP ground-level and a thermal BPP, which depends linearly on self-heating. Measurements as a function of pulse width confirm that self-heating rather than bias-level dominates. Diodes without trenches show low BPP ground-level, and a thermal BPP which depends strongly on mounting, due to changes in the temperature profile. The additional lateral guiding in diodes with trenches strongly increases the BPP ground-level, but optically isolates the stripe from the device edges, suppressing the influence of the thermal profile, leading to a BPP-slope that is low and independent of mounting. Trenches are also shown to initiate strain fields that cause parasitic TM-polarized emission with large BPP{sub lat}, whose influence on total BPP{sub lat} remains small, provided the overall polarization purity is >95%.

  20. Small fields output factors measurements and correction factors determination for several detectors for a CyberKnife{sup Registered-Sign} and linear accelerators equipped with microMLC and circular cones

    SciTech Connect (OSTI)

    Bassinet, C.; Huet, C.; Derreumaux, S.; Baumann, M.; Trompier, F.; Roch, P.; Clairand, I.; Brunet, G.; Gaudaire-Josset, S.; Chea, M.; Boisserie, G.

    2013-07-15

    Purpose: The use of small photon fields is now an established practice in stereotactic radiosurgery and radiotherapy. However, due to a lack of lateral electron equilibrium and high dose gradients, it is difficult to accurately measure the dosimetric quantities required for the commissioning of such systems. Moreover, there is still no metrological dosimetric reference for this kind of beam today. In this context, the first objective of this work was to determine and to compare small fields output factors (OF) measured with different types of active detectors and passive dosimeters for three types of facilities: a CyberKnife{sup Registered-Sign} system, a dedicated medical linear accelerator (Novalis) equipped with m3 microMLC and circular cones, and an adaptive medical linear accelerator (Clinac 2100) equipped with an additional m3 microMLC. The second one was to determine the k{sub Q{sub c{sub l{sub i{sub n,Q{sub m{sub s{sub r}{sup f{sub c}{sub l}{sub i}{sub n},f{sub m}{sub s}{sub r}}}}}}}}} correction factors introduced in a recently proposed small field dosimetry formalism for different active detectors.Methods: Small field sizes were defined either by microMLC down to 6 Multiplication-Sign 6 mm{sup 2} or by circular cones down to 4 mm in diameter. OF measurements were performed with several commercially available active detectors dedicated to measurements in small fields (high resolution diodes: IBA SFD, Sun Nuclear EDGE, PTW 60016, PTW 60017; ionizing chambers: PTW 31014 PinPoint chamber, PTW 31018 microLion liquid chamber, and PTW 60003 natural diamond). Two types of passive dosimeters were used: LiF microcubes and EBT2 radiochromic films.Results: Significant differences between the results obtained by several dosimetric systems were observed, particularly for the smallest field size for which the difference in the measured OF reaches more than 20%. For passive dosimeters, an excellent agreement was observed (better than 2%) between EBT2 and LiF microcubes for all OF measurements. Moreover, it has been shown that these passive dosimeters do not require correction factors and can then be used as reference dosimeters. Correction factors for the active detectors have then been determined from the mean experimental OF measured by the passive dosimeters.Conclusions: Four sets of correction factors needed to apply the new small field dosimetry formalism are provided for several active detectors. A protocol for small photon beams OF determination based on passive dosimeters measurements has been recently proposed to French radiotherapy treatment centers.

  1. DOE Order 458.1 Property Clearance Requirements and Factors Considered...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Factors Considered to Update Its Clearance Limits DOE Order 458.1 Property Clearance Requirements and Factors Considered to Update Its Clearance Limits Carlos Corredor, ...

  2. Contaminants in Buildings and Occupied Spaces as Risk Factors forOccupant Symptoms in U.S. Office Buildings: Findings from the U.S. EPABASE Study

    SciTech Connect (OSTI)

    Mendell, M.J.; Mirer, A.; Lei-Gomez, Q.

    2007-08-01

    Nonspecific building-related symptoms among occupants of modern office buildings worldwide are common and may be associated with important reductions in work performance, but their etiology remains uncertain. Most reported research into environmental risk factors for these symptoms has focused on ventilation system-related factors, dampness, and particle removal through filtration and cleaning, with relatively few studies of other potential sources of indoor contaminants. We analyzed data collected by the U.S. Environmental Protection Agency (EPA) from a representative sample of 100 large U.S. office buildings--the Building Assessment and Survey Evaluation (BASE) study--using multivariate-adjusted logistic regression models with generalized estimating equations. We estimated odds ratios (ORs) and 95% confidence intervals (CIs) for associations between seven building-related symptom outcomes and a diverse set of potential indoor and outdoor sources for indoor pollutants. Although most of the investigated risk factors showed no apparent association with building-related symptoms, some interesting associations resulted. Increased prevalence of symptoms was associated with carpets older than one year (lower respiratory symptoms), non-carpeted floors (upper and lower respiratory symptoms), older furniture (eye and skin symptoms), infrequent vacuuming (upper respiratory, eye, and skin symptoms and headache), and masonry exterior walls (cough, eye symptoms, and fatigue/concentration difficulty). For the many potential risk factors assessed, almost none had been investigated previously, and many associations found here may have been by chance. Additional confirmatory research focused on risk factors initially identified here is needed, using more objective measures of health outcomes and risk factors or exposures.

  3. Photoautotrophic symbiont and geography are major factors affecting highly structured and diverse bacterial communities in the lichen microbiome

    SciTech Connect (OSTI)

    Hodkinson, Brendan P; Gottel, Neil R; Schadt, Christopher Warren; Lutzoni, Francois

    2011-01-01

    Although common knowledge dictates that the lichen thallus is formed solely by a fungus (mycobiont) that develops a symbiotic relationship with an alga and/or cyanobacterium (photobiont), the non-photoautotrophic bacteria found in lichen microbiomes are increasingly regarded as integral components of lichen thalli. For this study, comparative analyses were conducted on lichen-associated bacterial communities to test for effects of photobiont-types (i.e. green algal vs. cyanobacterial), mycobiont-types and large-scale spatial distances (from tropical to arctic latitudes). Amplicons of the 16S (SSU) rRNA gene were examined using both Sanger sequencing of cloned fragments and barcoded pyrosequencing. Rhizobiales is typically the most abundant and taxonomically diverse order in lichen microbiomes; however, overall bacterial diversity in lichens is shown to be much higher than previously reported. Members of Acidobacteriaceae, Acetobacteraceae, Brucellaceae and sequence group LAR1 are the most commonly found groups across the phylogenetically and geographically broad array of lichens examined here. Major bacterial community trends are significantly correlated with differences in large-scale geography, photobiont-type and mycobiont-type. The lichen as a microcosm represents a structured, unique microbial habitat with greater ecological complexity and bacterial diversity than previously appreciated and can serve as a model system for studying larger ecological and evolutionary principles.

  4. Factors driving wind power development in the United States

    SciTech Connect (OSTI)

    Bird, Lori A.; Parsons, Brian; Gagliano, Troy; Brown, Matthew H.; Wiser, Ryan H.; Bolinger, Mark

    2003-05-15

    In the United States, there has been substantial recent growth in wind energy generating capacity, with growth averaging 24 percent annually during the past five years. About 1,700 MW of wind energy capacity was installed in 2001, while another 410 MW became operational in 2002. This year (2003) shows promise of significant growth with more than 1,500 MW planned. With this growth, an increasing number of states are experiencing investment in wind energy projects. Wind installations currently exist in about half of all U.S. states. This paper explores the key factors at play in the states that have achieved a substantial amount of wind energy investment. Some of the factors that are examined include policy drivers, such as renewable portfolio standards (RPS), federal and state financial incentives, and integrated resource planning; as well as market drivers, such as consumer demand for green power, natural gas price volatility, and wholesale market rules.

  5. Performance of non-conventional factorization approaches for neutron kinetics

    SciTech Connect (OSTI)

    Bulla, S.; Nervo, M.

    2013-07-01

    The use of factorization techniques provides a interesting option for the simulation of the time-dependent behavior of nuclear systems with a reduced computational effort. While point kinetics neglects all spatial and spectral effects, quasi-statics and multipoint kinetics allow to produce results with a higher accuracy for transients involving relevant modifications of the neutron distribution. However, in some conditions these methods can not work efficiently. In this paper, we discuss some possible alternative formulations for the factorization process for neutron kinetics, leading to mathematical models of reduced complications that can allow an accurate simulation of transients involving spatial and spectral effects. The performance of these innovative approaches are compared to standard techniques for some test cases, showing the benefits and shortcomings of the method proposed. (authors)

  6. Factors that affect electric-utility stranded commitments

    SciTech Connect (OSTI)

    Hirst, E.; Hadley, S.; Baxter, L.

    1996-07-01

    Estimates of stranded commitments for U.S. investor-owned utilities range widely, with many falling in the range of $100 to $200 billion. These potential losses exist because some utility-owned power plants, long-term power-purchase contracts and fuel-supply contracts, regulatory assets, and expenses for public-policy programs have book values that exceed their expected market values under full competition. This report quantifies the sensitivity of stranded- commitment estimates to the various factors that lead to these above- market-value estimates. The purpose of these sensitivity analyses is to improve understanding on the part of state and federal regulators, utilities, customers, and other electric-industry participants about the relative importance of the factors that affect stranded- commitment amounts.

  7. Measurement of the gamma gamma* -> pi0 transition form factor

    SciTech Connect (OSTI)

    Aubert, B.

    2009-06-02

    We study the reaction e{sup +}e{sup -} {yields} e{sup +}e{sup -}{pi}{sup 0} in the single tag mode and measure the differential cross section d{sigma}/dQ{sup 2} and the {gamma}{gamma}* {yields} {pi}{sup 0} transition form factor in the mometum transfer range from 4 to 40 GeV{sup 2}. At Q{sup 2} > 10 GeV{sup 2} the measured form factor exceeds the asymptotic limit predicted by perturbative QCD. The analysis is based on 442 fb{sup -1} of integrated luminosity collected at PEP-II with the BABAR detector at e{sup +}e{sup -} center-of-mass energies near 10.6 GeV.

  8. Structure of Plasmodium falciparum ADP-ribosylation factor 1

    SciTech Connect (OSTI)

    Cook, William J.; Smith, Craig D.; Senkovich, Olga; Holder, Anthony A.; Chattopadhyay, Debasish

    2011-09-26

    Vesicular trafficking may play a crucial role in the pathogenesis and survival of the malaria parasite. ADP-ribosylation factors (ARFs) are among the major components of vesicular trafficking pathways in eukaryotes. The crystal structure of ARF1 GTPase from Plasmodium falciparum has been determined in the GDP-bound conformation at 2.5 {angstrom} resolution and is compared with the structures of mammalian ARF1s.

  9. Method for determining formation quality factor from seismic data

    DOE Patents [OSTI]

    Taner, M. Turhan; Treitel, Sven

    2005-08-16

    A method is disclosed for calculating the quality factor Q from a seismic data trace. The method includes calculating a first and a second minimum phase inverse wavelet at a first and a second time interval along the seismic data trace, synthetically dividing the first wavelet by the second wavelet, Fourier transforming the result of the synthetic division, calculating the logarithm of this quotient of Fourier transforms and determining the slope of a best fit line to the logarithm of the quotient.

  10. Transcription factors for modification of lignin content in plants

    SciTech Connect (OSTI)

    Wang, Huanzhong; Chen, Fang; Dixon, Richard A.

    2015-06-02

    The invention provides methods for modifying lignin, cellulose, xylan, and hemicellulose content in plants, and for achieving ectopic lignification and, for instance, secondary cell wall synthesis in pith cells, by altered regulation of a WRKY transcription factor. Nucleic acid constructs for altered WRKY-TF expression are described. Transgenic plants are provided that comprise modified pith cell walls, and lignin, cellulose, and hemicellulose content. Plants described herein may be used, for example, as improved biofuel feedstock and as highly digestible forage crops.

  11. Limiting Factors for Convective Cloud Top Height in the Tropics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Limiting Factors for Convective Cloud Top Height in the Tropics M. P. Jensen and A. D. Del Genio National Aeronautics and Space Administration Goddard Institute for Space Studies Columbia University New York, New York Introduction Populations of tropical convective clouds are mainly comprised of three types: shallow trade cumulus, mid-level cumulus congestus and deep convective clouds (Johnson et al. 1999). Each of these cloud types has different impacts on the local radiation and water budgets.

  12. Factors Affecting HCCI Combustion Phasing for Fuels with Single- and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dual-Stage Chemistry | Department of Energy Affecting HCCI Combustion Phasing for Fuels with Single- and Dual-Stage Chemistry Factors Affecting HCCI Combustion Phasing for Fuels with Single- and Dual-Stage Chemistry 2004 Diesel Engine Emissions Reduction (DEER) Conference Presentation: Sandia National Laboratories PDF icon 2004_deer_dec.pdf More Documents & Publications Microsoft PowerPoint - DEER03-P.ppt HCCI and Stratified-Charge CI Engine Combustion Research Improving Efficiency and

  13. Method for factor analysis of GC/MS data

    DOE Patents [OSTI]

    Van Benthem, Mark H; Kotula, Paul G; Keenan, Michael R

    2012-09-11

    The method of the present invention provides a fast, robust, and automated multivariate statistical analysis of gas chromatography/mass spectroscopy (GC/MS) data sets. The method can involve systematic elimination of undesired, saturated peak masses to yield data that follow a linear, additive model. The cleaned data can then be subjected to a combination of PCA and orthogonal factor rotation followed by refinement with MCR-ALS to yield highly interpretable results.

  14. Human factors engineering report for the cold vacuum drying facility

    SciTech Connect (OSTI)

    IMKER, F.W.

    1999-06-30

    The purpose of this report is to present the results and findings of the final Human Factors Engineering (HFE) technical analysis and evaluation of the Cold Vacuum Drying Facility (CVDF). Ergonomics issues are also addressed in this report, as appropriate. This report follows up and completes the preliminary work accomplished and reported by the Preliminary HFE Analysis report (SNF-2825, Spent Nuclear Fuel Project Cold Vacuum Drying Facility Human Factors Engineering Analysis: Results and Findings). This analysis avoids redundancy of effort except for ensuring that previously recommended HFE design changes have not affected other parts of the system. Changes in one part of the system may affect other parts of the system where those changes were not applied. The final HFE analysis and evaluation of the CVDF human-machine interactions (HMI) was expanded to include: the physical work environment, human-computer interface (HCI) including workstation and software, operator tasks, tools, maintainability, communications, staffing, training, and the overall ability of humans to accomplish their responsibilities, as appropriate. Key focal areas for this report are the process bay operations, process water conditioning (PWC) skid, tank room, and Central Control Room operations. These key areas contain the system safety-class components and are the foundation for the human factors design basis of the CVDF.

  15. Critical success factors in implementing process safety management

    SciTech Connect (OSTI)

    Wilson, D.J. [Chevron USA, Inc., New Orleans, LA (United States)

    1996-08-01

    This paper focuses on several {open_quotes}Critical Success Factors {close_quotes} which will determine how well employees will embrace and utilize the changes being asked of them to implement Process Safety Management (PSM). These success factors are applicable to any change which involves asking employees to perform activities differently than they are currently performing them. This includes changes in work processes (the way we arrange and conduct a set of tasks) or changes in work activities (how we perform individual tasks). Simply developing new work processes and explaining them to employees is not enough to ensure that employees will actually utilize them -- no matter how good these processes are. To ensure successful, complete implementation of Process Safety Management, we must manage the transition from how we perform our work now to how we will perform it after PSM is implemented. Environmental and safety performance improvements, facility reliability and operability increases, and employee effectiveness and productivity gains CAN NOT be achieved until Process Safety Management processes are fully implemented. To successfully implement management of change, mechanical integrity, or any of the other processes in PSM, each of the following critical success factors must be carefully considered and utilized as appropriate. They are: (1) Vision of a Future State, Current State Assessment, and a Detailed Plan to Achieve the Future State, (2) Management Commitment, (3) Ownership by Key Individuals, (4) Justification for Actions, (5) Autonomy to Customize the Process, (6) Feedback Mechanism to Adjust Activities, and (7) Process to Refocus & Redirect Efforts.

  16. Dirac equation in low dimensions: The factorization method

    SciTech Connect (OSTI)

    Sánchez-Monroy, J.A.; Quimbay, C.J.

    2014-11-15

    We present a general approach to solve the (1+1) and (2+1)-dimensional Dirac equations in the presence of static scalar, pseudoscalar and gauge potentials, for the case in which the potentials have the same functional form and thus the factorization method can be applied. We show that the presence of electric potentials in the Dirac equation leads to two Klein–Gordon equations including an energy-dependent potential. We then generalize the factorization method for the case of energy-dependent Hamiltonians. Additionally, the shape invariance is generalized for a specific class of energy-dependent Hamiltonians. We also present a condition for the absence of the Klein paradox (stability of the Dirac sea), showing how Dirac particles in low dimensions can be confined for a wide family of potentials. - Highlights: • The low-dimensional Dirac equation in the presence of static potentials is solved. • The factorization method is generalized for energy-dependent Hamiltonians. • The shape invariance is generalized for energy-dependent Hamiltonians. • The stability of the Dirac sea is related to the existence of supersymmetric partner Hamiltonians.

  17. Automatic Blocking Of QR and LU Factorizations for Locality

    SciTech Connect (OSTI)

    Yi, Q; Kennedy, K; You, H; Seymour, K; Dongarra, J

    2004-03-26

    QR and LU factorizations for dense matrices are important linear algebra computations that are widely used in scientific applications. To efficiently perform these computations on modern computers, the factorization algorithms need to be blocked when operating on large matrices to effectively exploit the deep cache hierarchy prevalent in today's computer memory systems. Because both QR (based on Householder transformations) and LU factorization algorithms contain complex loop structures, few compilers can fully automate the blocking of these algorithms. Though linear algebra libraries such as LAPACK provides manually blocked implementations of these algorithms, by automatically generating blocked versions of the computations, more benefit can be gained such as automatic adaptation of different blocking strategies. This paper demonstrates how to apply an aggressive loop transformation technique, dependence hoisting, to produce efficient blockings for both QR and LU with partial pivoting. We present different blocking strategies that can be generated by our optimizer and compare the performance of auto-blocked versions with manually tuned versions in LAPACK, both using reference BLAS, ATLAS BLAS and native BLAS specially tuned for the underlying machine architectures.

  18. Transfer Factors for Contaminant Uptake by Fruit and Nut Trees

    SciTech Connect (OSTI)

    Napier, Bruce A.; Fellows, Robert J.; Minc, Leah D.

    2013-11-20

    Transfer of radionuclides from soils into plants is one of the key mechanisms for long-term contamination of the human food chain. Nearly all computer models that address soil-to-plant uptake of radionuclides use empirically-derived transfer factors to address this process. Essentially all available soil-to-plant transfer factors are based on measurements in annual crops. Because very few measurements are available for tree fruits, samples were taken of alfalfa and oats and the stems, leaves, and fruits and nuts of almond, apple, apricot, carob, fig, grape, nectarine, pecan, pistachio (natural and grafted), and pomegranate, along with local surface soil. The samples were dried, ground, weighed, and analyzed for trace constituents through a combination of induction-coupled plasma mass spectrometry and instrumental neutron activation analysis for a wide range of naturally-occurring elements. Analysis results are presented and converted to soil-to-plant transfer factors. These are compared to commonly used and internationally recommended values. Those determined for annual crops are very similar to commonly-used values; those determined for tree fruits show interesting differences. Most macro- and micronutrients are slightly reduced in fruits; non-essential elements are reduced further. These findings may be used in existing computer models and may allow development of tree-fruit-specific transfer models.

  19. A decision support system prototype including human factors based on the TOGA meta-theory approach

    SciTech Connect (OSTI)

    Cappelli, M.; Memmi, F.; Gadomski, A. M.; Sepielli, M.

    2012-07-01

    The human contribution to the risk of operation of complex technological systems is often not negligible and sometimes tends to become significant, as shown by many reports on incidents and accidents occurred in the past inside Nuclear Power Plants (NPPs). An error of a human operator of a NPP can derive by both omission and commission. For instance, complex commission errors can also lead to significant catastrophic technological accidents, as for the case of the Three Mile Island accident. Typically, the problem is analyzed by focusing on the single event chain that has provoked the incident or accident. What is needed is a general framework able to include as many parameters as possible, i.e. both technological and human factors. Such a general model could allow to envisage an omission or commission error before it can happen or, alternatively, suggest preferred actions to do in order to take countermeasures to neutralize the effect of the error before it becomes critical. In this paper, a preliminary Decision Support System (DSS) based on the so-called (-) TOGA meta-theory approach is presented. The application of such a theory to the management of nuclear power plants has been presented in the previous ICAPP 2011. Here, a human factor simulator prototype is proposed in order to include the effect of human errors in the decision path. The DSS has been developed using a TRIGA research reactor as reference plant, and implemented using the LabVIEW programming environment and the Finite State Machine (FSM) model The proposed DSS shows how to apply the Universal Reasoning Paradigm (URP) and the Universal Management Paradigm (UMP) to a real plant context. The DSS receives inputs from instrumentation data and gives as output a suggested decision. It is obtained as the result of an internal elaborating process based on a performance function. The latter, describes the degree of satisfaction and efficiency, which are dependent on the level of responsibility related to each professional role. As an application, we present the simulation of the discussed error, e.g. the unchecked extraction of the control rods during a power variation maneuver and we show how the effect of human errors can affect the performance function, giving rise to different countermeasures which could call different operator figures into play, potentially not envisaged in the standard procedure. (authors)

  20. Olive oil compounds inhibit vascular endothelial growth factor receptor-2 phosphorylation

    SciTech Connect (OSTI)

    Lamy, Sylvie Ouanouki, Amira; Béliveau, Richard; Desrosiers, Richard R.

    2014-03-10

    Vascular endothelial growth factor (VEGF) triggers crucial signaling processes that regulate tumor angiogenesis and, therefore, represents an attractive target for the development of novel anticancer therapeutics. Several epidemiological studies have confirmed that abundant consumption of foods from plant origin is associated with reduced risk of developing cancers. In the Mediterranean basin, the consumption of extra virgin olive oil is an important constituent of the diet. Compared to other vegetable oils, the presence of several phenolic antioxidants in olive oil is believed to prevent the occurrence of a variety of pathological processes, such as cancer. While the strong antioxidant potential of these molecules is well characterized, their antiangiogenic activities remain unknown. The aim of this study is to investigate whether tyrosol (Tyr), hydroxytyrosol (HT), taxifolin (Tax), oleuropein (OL) and oleic acid (OA), five compounds contained in extra virgin olive oil, can affect in vitro angiogenesis. We found that HT, Tax and OA were the most potent angiogenesis inhibitors through their inhibitory effect on specific autophosphorylation sites of VEGFR-2 (Tyr951, Tyr1059, Tyr1175 and Tyr1214) leading to the inhibition of endothelial cell (EC) signaling. Inhibition of VEGFR-2 by these olive oil compounds significantly reduced VEGF-induced EC proliferation and migration as well as their morphogenic differentiation into capillary-like tubular structures in Matrigel. Our study demonstrates that HT, Tax and OA are novel and potent inhibitors of the VEGFR-2 signaling pathway. These findings emphasize the chemopreventive properties of olive oil and highlight the importance of nutrition in cancer prevention. - Highlights: • We investigated five compounds contained in extra virgin olive oil on angiogenesis. • Hydroxytyrosol, taxifolin and oleic acid are the best angiogenesis inhibitors. • Olive oil compounds affect endothelial cell functions essential for angiogenesis. • Olive oil compounds inhibit specific autophosphorylation sites of VEGFR-2. • Hydroxytyrosol, taxifolin and oleic acid inhibit VEGFR-2 signaling pathway.

  1. Model-Based Analysis of the Role of Biological, Hydrological and Geochemical Factors Affecting Uranium Bioremediation

    SciTech Connect (OSTI)

    Zhao, Jiao; Scheibe, Timothy D.; Mahadevan, Radhakrishnan

    2011-01-24

    Uranium contamination is a serious concern at several sites motivating the development of novel treatment strategies such as the Geobacter-mediated reductive immobilization of uranium. However, this bioremediation strategy has not yet been optimized for the sustained uranium removal. While several reactive-transport models have been developed to represent Geobacter-mediated bioremediation of uranium, these models often lack the detailed quantitative description of the microbial process (e.g., biomass build-up in both groundwater and sediments, electron transport system, etc.) and the interaction between biogeochemical and hydrological process. In this study, a novel multi-scale model was developed by integrating our recent model on electron capacitance of Geobacter (Zhao et al., 2010) with a comprehensive simulator of coupled fluid flow, hydrologic transport, heat transfer, and biogeochemical reactions. This mechanistic reactive-transport model accurately reproduces the experimental data for the bioremediation of uranium with acetate amendment. We subsequently performed global sensitivity analysis with the reactive-transport model in order to identify the main sources of prediction uncertainty caused by synergistic effects of biological, geochemical, and hydrological processes. The proposed approach successfully captured significant contributing factors across time and space, thereby improving the structure and parameterization of the comprehensive reactive-transport model. The global sensitivity analysis also provides a potentially useful tool to evaluate uranium bioremediation strategy. The simulations suggest that under difficult environments (e.g., highly contaminated with U(VI) at a high migration rate of solutes), the efficiency of uranium removal can be improved by adding Geobacter species to the contaminated site (bioaugmentation) in conjunction with the addition of electron donor (biostimulation). The simulations also highlight the interactive effect of initial cell concentration and flow rate on U(VI) reduction.

  2. Mobil-Marathon and similar oil company mergers. Hearing before the Subcommittee on Fossil and Synthetic Fuels of the Committee on Energy and Commerce, House of Representatives, Ninety-Seventh Congress, First Session on H. R. 4930

    SciTech Connect (OSTI)

    Not Available

    1982-01-01

    Subcommittee chairman Phillip R. Sharp's opening statement notes that a wave of large horizontal and vertical mergers are the result of rising oil prices and oil-reserve values, price decontrol, and a relaxation of anti-merger enforcement by the Reagan administration. US merger activity in 1981 had a $20 billion value, half of which involved oil, gas, mining, and mineral companies. Chairman Sharp further notes that the mergers will raise customer costs and eliminate many small companies, which indirectly retards new exploration. H.R. 4930 requires a study of these effects and provides for a moratorium on larger mergers until the study is completed. The testimony of eight witnesses representing oil companies and related groups follows the text of H.R. 4930. Additional material submitted for the record includes a resolution by the Illinois Petroleum Marketers Association expressing their concern about the impact of mergers. (DCK)

  3. Hazardous waste and the stringfellow acid pits. Hearing before the Subcommittee on Natural Resources, Agriculture Research and Environment of the Committee on Science and Technology, US House of Representatives, Ninety-Eighth Congress, First Session, April 22, 1983

    SciTech Connect (OSTI)

    Not Available

    1985-01-01

    California residents and state and federal officials testified at a field hearing in Glen Avon, California on the cleanup operations at the Stringfellow acid pits, an abandoned site, under the Superfund law. Sally Tanner, Chairwoman of the State Assembly Committee on Consumer Protection and Toxic Chemicals, expressed disappointment that the federal program did not match state readiness to solve the problem. The Environmental Protection Agency's (EPA's) failure to use available funds and to listen to public concerns has been frustrating to Californians concerned about health hazards. Other witnesses spoke of the improbability of a complete cleanup because of groundwater migration and flooding in the area. EPA representatives described cleanup procedures at the site. An appendix with additional material submitted for the record follows the testimony of 11 witnesses.

  4. Gyromagnetic factors in {sup 144-150}Nd

    SciTech Connect (OSTI)

    Giannatiempo, A.

    2011-09-15

    The U(5) to SU(3) evolution of the nuclear structure in the even {sup 144-156}Nd isotopes has been investigated in the framework of the interacting boson approximation (IBA-2) model, taking into account the effect of the partial Z=64 subshell closure on the structure of the states of a collective nature. The analysis, which led to a satisfactory description of excitation energy patterns, quadrupole moments, and decay properties of the states (even when important M1 components were present in the transitions), is extended to the available data on g factors, in {sup 144-150}Nd. Their values are reasonably reproduced by the calculations.

  5. On the relationship between formation resistivity factor and porosity

    SciTech Connect (OSTI)

    Perez-Rosales, C.

    1982-08-01

    A theory on the relationship between formation resistivity factor and porosity is presented. This theory considers that, from the standpoint of the flow of electric current within a porous medium saturated with a conducting fluid, the pore space can be divided into flowing and stagnant regions. This assumption leads to a general expression, and formulas currently used in practice are special cases of this expression. The validity of the new expression is established by the use of data corresponding to sandstones and packings and suspensions of particles. For the case of natural rocks, the theory confirms Darcy's equation and gives an interpretation of the physical significance of the so-called cementation exponent.

  6. Greybody factors and charges in Kerr/CFT

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Cvetič, Mirjam; Larsen, Finn

    2009-09-01

    We compute greybody factors for near extreme Kerr black holes in D = 4 and D = 5. In D = 4 we include four charges so that our solutions can be continuously deformed to the BPS limit. In D = 5 we include two independent angular momenta so Left-Right symmetry is incorporated. We discuss the CFT interpretation of our emission amplitudes, including the overall frequency dependence and the dependence on all black hole parameters. We find that all additional parameters can be incorporated Kerr/CFT, with central charge independent of U(1) charges.

  7. EIA-Voluntary Reporting of Greenhouse Gases Program - Emission Factors and

    Gasoline and Diesel Fuel Update (EIA)

    Global Warming Emission Factors Voluntary Reporting of Greenhouse Gases Program Emission Factors and Global Warming Potentials The greenhouse gas emission factors and global warming potentials (GWPs) presented on this page should be used for preparing emission inventories and calculating emission reductions submitted to U.S. Energy Information Administration (EIA) on Form EIA-1605(b). Fuel and Energy Emission Factors: Instructions | HTML | Tables Electricity Emission Factors: Instructions |

  8. Asymptotic, multigroup flux reconstruction and consistent discontinuity factors

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Trahan, Travis J.; Larsen, Edward W.

    2015-05-12

    Recent theoretical work has led to an asymptotically derived expression for reconstructing the neutron flux from lattice functions and multigroup diffusion solutions. The leading-order asymptotic term is the standard expression for flux reconstruction, i.e., it is the product of a shape function, obtained through a lattice calculation, and the multigroup diffusion solution. The first-order asymptotic correction term is significant only where the gradient of the diffusion solution is not small. Inclusion of this first-order correction term can significantly improve the accuracy of the reconstructed flux. One may define discontinuity factors (DFs) to make certain angular moments of the reconstructed fluxmore » continuous across interfaces between assemblies in 1-D. Indeed, the standard assembly discontinuity factors make the zeroth moment (scalar flux) of the reconstructed flux continuous. The inclusion of the correction term in the flux reconstruction provides an additional degree of freedom that can be used to make two angular moments of the reconstructed flux continuous across interfaces by using current DFs in addition to flux DFs. Thus, numerical results demonstrate that using flux and current DFs together can be more accurate than using only flux DFs, and that making the second angular moment continuous can be more accurate than making the zeroth moment continuous.« less

  9. Systems Biology Model of Interactions Between Tissue Growth Factors and DNA Damage Pathways: Low Dose Response and Cross-Talk in TGFbeta and ATM Signaling

    SciTech Connect (OSTI)

    O'Neill, Peter; Anderson, Jennifer

    2014-10-02

    The etiology of radiation carcinogenesis has been described in terms of aberrant changes that span several levels of biological organization. Growth factors regulate many important cellular and tissue functions including apoptosis, differentiation and proliferation. A variety of genetic and epigenetic changes of growth factors have been shown to contribute to cancer initiation and progression. It is known that cellular and tissue damage to ionizing radiation is in part initiated by the production of reactive oxygen species, which can activate cytokine signaling, and the DNA damage response pathways, most notably the ATM signaling pathway. Recently the transforming growth factor ? (TGF?) pathway has been shown to regulate or directly interact with the ATM pathway in the response to radiation. The relevance of this interaction with the ATM pathway is not known although p53 becomes phosphorylated and DNA damage responses are involved. However, growth factor interactions with DNA damage responses have not been elucidated particularly at low doses and further characterization of their relationship to cancer processes is warranted. Our goal will be to use a systems biology approach to mathematically and experimentally describe the low dose responses and cross-talk between the ATM and TGF? pathways initiated by low and high LET radiation. We will characterize ATM and TGF? signaling in epithelial and fibroblast cells using 2D models and ultimately extending to 3D organotypic cell culture models to begin to elucidate possible differences that may occur for different cell types and/or inter-cellular communication. We will investigate the roles of the Smad and Activating transcription factor 2 (ATF2) proteins as the potential major contributors to cross- talk between the TGF? and ATM pathways, and links to cell cycle control and/or the DNA damage response, and potential differences in their responses at low and high doses. We have developed various experimental approaches to apply to these problems using confocal microscopy and flow cytometry to detail changes at low dose/dose-rate in order to understand individual cell responses, and will establish our mathematical models based on the experimental findings resulting from changes in DNA repair, apoptosis and proliferation.

  10. Control of mechanically activated polymersome fusion: Factors affecting fusion

    SciTech Connect (OSTI)

    Henderson, Ian M.; Paxton, Walter F.

    2014-12-15

    Previously we have studied the mechanically-activated fusion of extruded (200 nm) polymer vesicles into giant polymersomes using agitation in the presence of salt. In this study we have investigated several factors contributing to this phenomenon, including the effects of (i) polymer vesicle concentration, (ii) agitation speed and duration, and iii) variation of the salt and its concentration. It was found that increasing the concentration of the polymer dramatically increases the production of giant vesicles through the increased collisions of polymersomes. Our investigations also found that increasing the frequency of agitation increased the efficiency of fusion, though ultimately limited the size of vesicle which could be produced due to the high shear involved. Finally it was determined that salt-mediation of the fusion process was not limited to NaCl, but is instead a general effect facilitated by the presence of solvated ionic compounds, albeit with different salts initiating fusion at different concentration.

  11. Control of mechanically activated polymersome fusion: Factors affecting fusion

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Henderson, Ian M.; Paxton, Walter F.

    2014-12-15

    Previously we have studied the mechanically-activated fusion of extruded (200 nm) polymer vesicles into giant polymersomes using agitation in the presence of salt. In this study we have investigated several factors contributing to this phenomenon, including the effects of (i) polymer vesicle concentration, (ii) agitation speed and duration, and iii) variation of the salt and its concentration. It was found that increasing the concentration of the polymer dramatically increases the production of giant vesicles through the increased collisions of polymersomes. Our investigations also found that increasing the frequency of agitation increased the efficiency of fusion, though ultimately limited the sizemore » of vesicle which could be produced due to the high shear involved. Finally it was determined that salt-mediation of the fusion process was not limited to NaCl, but is instead a general effect facilitated by the presence of solvated ionic compounds, albeit with different salts initiating fusion at different concentration.« less

  12. Making tensor factorizations robust to non-gaussian noise.

    SciTech Connect (OSTI)

    Chi, Eric C.; Kolda, Tamara Gibson

    2011-03-01

    Tensors are multi-way arrays, and the CANDECOMP/PARAFAC (CP) tensor factorization has found application in many different domains. The CP model is typically fit using a least squares objective function, which is a maximum likelihood estimate under the assumption of independent and identically distributed (i.i.d.) Gaussian noise. We demonstrate that this loss function can be highly sensitive to non-Gaussian noise. Therefore, we propose a loss function based on the 1-norm because it can accommodate both Gaussian and grossly non-Gaussian perturbations. We also present an alternating majorization-minimization (MM) algorithm for fitting a CP model using our proposed loss function (CPAL1) and compare its performance to the workhorse algorithm for fitting CP models, CP alternating least squares (CPALS).

  13. Factors relevant to utility integration of intermittent renewable technologies

    SciTech Connect (OSTI)

    Wan, Yih-huei; Parsons, B.K.

    1993-08-01

    This study assesses factors that utilities must address when they integrate intermittent renewable technologies into their power-supply systems; it also reviews the literature in this area and has a bibliography containing more than 350 listings. Three topics are covered: (1) interface (hardware and design-related interconnection), (2) operability/stability, and (3) planning. This study finds that several commonly held perceptions regarding integration of intermittent renewable energy technologies are not valid. Among findings of the study are the following: (1) hardware and system design advances have eliminated most concerns about interface; (2) cost penalties have not occurred at low to moderate penetration levels (and high levels are feasible); and (3) intermittent renewable energy technologies can have capacity values. Obstacles still interfering with intermittent renewable technologies are also identified.

  14. Thermoflexus hugenholtzii gen. nov., sp. nov., a thermophilic, microaerophilic, filamentous bacterium representing a novel class in the Chloroflexi, Thermoflexia classis nov., and description of Thermoflexaceae fam. nov. and Thermoflexales ord. nov.

    SciTech Connect (OSTI)

    Dodsworth, Jeremy A.; Gevorkian, Jonathan; Despujos, Fairuz; Cole, Jesse; Murugapiran, Senthil K.; Ming, Hong; Li, Wen J.; Zhang, Gengxin; Dohnalkova, Alice; Hedlund, Brian P.

    2014-06-06

    A thermophilic, filamentous, heterotrophic bacterium designated strain JAD2T was isolated from sediment of Great Boiling Spring in Nevada, USA. Cells had an average diameter of 0.3 µm and length of 4.0 µm, and formed filaments typically ranging in length from 20 µm to 200 µm. Filaments were negative for the Gram stain reaction, spores were not formed, and motility was not observed. The optimum temperature for growth was 75 °C with a range from 67.5-75 °C, and the optimum pH for growth was 6.75 with a range from 6.5-7.75. Peptone, tryptone or yeast extract were able to support growth when supplemented with a vitamin solution, but no growth was observed using a variety of defined organic substrates. Strain JAD2T was a facultative microaerophile, with optimal growth at 1% v/v O2 and an upper limit of 8% O2, and anaerobic growth was stimulated by fumarate but inhibited by sulfite and elemental sulfur. The major cellular fatty acids (>5%) were C16:0, C19:0, C18:0, C20:0, and C19:1. The genomic DNA G+C content was 69.3%. Phylogenetic and phylogenomic analyses using 16S rRNA gene sequences and other conserved genes placed JAD2T and other members of the yet-uncultivated GAL35 group within the phylum Chloroflexi, but not within any existing class in this phylum. These results indicate that strain JAD2T is the first cultivated representative of a new lineage within the phylum Chloroflexi, for which we propose the name Thermoflexus hugenholtzii gen. nov., sp. nov., type strain JAD2T, within Thermoflexia classis nov., Thermoflexales ord. nov., and Thermoflexaceae fam. nov.

  15. Energy Price Indices and Discount Factors for Life-Cycle Cost...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Price Indices and Discount Factors for Life-Cycle Cost Analysis - 2015 Energy Price Indices and Discount Factors for Life-Cycle Cost Analysis - 2015 Handbook describes the annual...

  16. Central safety factor and β N control on NSTX-U via beam power...

    Office of Scientific and Technical Information (OSTI)

    Central safety factor and N control on NSTX-U via beam power and plasma boundary shape ... Title: Central safety factor and N control on NSTX-U via beam power and plasma boundary ...

  17. Meson transition form factors in light-front holographic QCD

    SciTech Connect (OSTI)

    Brodsky, Stanley J.; Cao Fuguang; de Teramond, Guy F.

    2011-10-01

    We study the photon-to-meson transition form factors (TFFs) F{sub M}{gamma}(Q{sup 2}) for {gamma}{gamma}{sup *}{yields}M using light-front holographic methods. The Chern-Simons action, which is a natural form in five-dimensional anti-de Sitter (AdS) space, is required to describe the anomalous coupling of mesons to photons using holographic methods and leads directly to an expression for the photon-to-pion TFF for a class of confining models. Remarkably, the predicted pion TFF is identical to the leading order QCD result where the distribution amplitude has asymptotic form. The Chern-Simons form is local in AdS space and is thus somewhat limited in its predictability. It only retains the qq component of the pion wave function, and further, it projects out only the asymptotic form of the meson distribution amplitude. It is found that in order to describe simultaneously the decay process {pi}{sup 0}{yields}{gamma}{gamma} and the pion TFF at the asymptotic limit, a probability for the qq component of the pion wave function P{sub qq}=0.5 is required, thus giving indication that the contributions from higher Fock states in the pion light-front wave function need to be included in the analysis. The probability for the Fock state containing four quarks P{sub qqqq}{approx}10%, which follows from analyzing the hadron matrix elements for a dressed current model, agrees with the analysis of the pion elastic form factor using light-front holography including higher Fock components in the pion wave function. The results for the TFFs for the {eta} and {eta}{sup '} mesons are also presented. The rapid growth of the pion TFF exhibited by the BABAR data at high Q{sup 2} is not compatible with the models discussed in this article, whereas the theoretical calculations are in agreement with the experimental data for the {eta} and {eta}{sup '} TFFs.

  18. Decommissioning Cost Estimating Factors And Earned Value Integration

    SciTech Connect (OSTI)

    Sanford, P.C.; Cimmarron, E.

    2008-07-01

    The Rocky Flats 771 Project progressed from the planning stage of decommissioning a plutonium facility, through the strip-out of highly-contaminated equipment, removal of utilities and structural decontamination, and building demolition. Actual cost data was collected from the strip-out activities and compared to original estimates, allowing the development of cost by equipment groupings and types and over time. Separate data was developed from the project control earned value reporting and compared with the equipment data. The paper discusses the analysis to develop the detailed factors for the different equipment types, and the items that need to be considered during characterization of a similar facility when preparing an estimate. The factors are presented based on direct labor requirements by equipment type. The paper also includes actual support costs, and examples of fixed or one-time start-up costs. The integration of the estimate and the earned value system used for the 771 Project is also discussed. The paper covers the development of the earned value system as well as its application to a facility to be decommissioned and an existing work breakdown structure. Lessons learned are provided, including integration with scheduling and craft supervision, measurement approaches, and verification of scope completion. In summary: The work of decommissioning the Rocky Flats 771 Project process equipment was completed in 2003. Early in the planning process, we had difficulty in identifying credible data and implementing processes for estimating and controlling this work. As the project progressed, we were able to collect actual data on the costs of removing plutonium contaminated equipment from various areas over the life of this work and associate those costs with individual pieces of equipment. We also were able to develop and test out a system for measuring the earned value of a decommissioning project based on an evolving estimate. These were elements that would have been useful to us in our early planning process, and we would expect that they would find application elsewhere as the DOE weapons complex and some commercial nuclear facilities move towards closure. (authors)

  19. Global Agricultural Supply and Demand: Factors Contributing to the Recent Increase in Food Commodity Prices

    SciTech Connect (OSTI)

    none,

    2008-05-01

    This report discusses the factors that have led to global food commodity price inflaction and addresses the resulting implications.

  20. A Model for Water Factor Measurements With Fission-Neutron Logging Tools

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (May 1983) | Department of Energy A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) PDF icon A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) More Documents & Publications Field Calibration Facilities for Environmental Measurement of Radium, Thorium, and

  1. Use of green fluorescent fusion protein to track activation of the transcription factor osterix during early osteoblast differentiation

    SciTech Connect (OSTI)

    Tai Guangping; Christodoulou, Ioannis; Bishop, Anne E.; Polak, Julia M. . E-mail: julia.polak@imperial.ac.uk

    2005-08-12

    Osterix (Osx) is a transcription factor required for the differentiation of preosteoblasts into fully functioning osteoblasts. However, the pattern of Osx activation during preosteoblast differentiation and maturation has not been clearly defined. Our aim was to study Osx activation during these processes in osteoblasts differentiating from murine and human embryonic stem cells (ESC). To do this, we constructed an Osx-GFP fusion protein reporter system to track Osx translocation within the cells. The distribution of Osx-GFP at representative stages of differentiation was also investigated by screening primary osteoblasts, mesenchymal stem cells, synoviocytes, and pre-adipocytes. Our experiments revealed that Osx-GFP protein was detectable in the cytoplasm of cultured, differentiated ESC 4 days after plating of enzymatically dispersed embryoid bodies. Osterix-GFP protein became translocated into the nucleus on day 7 following transfer of differentiated ESC to osteogenic medium. After 14 days of differentiation, cells showing nuclear translocation of Osx-GFP formed rudimentary bone nodules that continued to increase in number over the following weeks (through day 21). We also found that Osx translocated into the nuclei of mesenchymal stem cells (C3H10T1/2) and pre-osteoblasts (MC3T3-E1) and showed partial activation in pre-adipocytes (MC3T3-L1). These data suggest that Osx activation occurs at a very early point in the differentiation of the mesenchymal-osteoblastic lineage.

  2. A Review of Operational Water Consumption and Withdrawal Factors for Electricity Generating Technologies

    SciTech Connect (OSTI)

    Macknick, Jordan; Newmark, Robin; Heath, Garvin; Hallett, K. C.

    2011-03-01

    This report provides estimates of operational water withdrawal and water consumption factors for electricity generating technologies in the United States. Estimates of water factors were collected from published primary literature and were not modified except for unit conversions. The presented water factors may be useful in modeling and policy analyses where reliable power plant level data are not available.

  3. Extracellular nonmitogenic angiogenesis factor and method of isolation thereof from wound fluid

    DOE Patents [OSTI]

    Banda, Michael J. (San Francisco, CA); Werb, Zena (San Francisco, CA); Knighton, David R. (San Francisco, CA); Hunt, Thomas K. (San Francisco, CA)

    1985-01-01

    A nonmitogenic angiogenesis factor is isolated from wound fluid by dialysis to include materials in the molecular size range of 2,000 to 14,000, lyophilization, and chromatography. The nonmitogenic angiogenesis factor is identified by activity by corneal implant assay and by cell migration assay. The angiogenesis factor is also characterized by inactivity by mitogenesis assay.

  4. Extracellular nonmitogenic angiogenesis factor and method of isolation thereof from wound fluid

    DOE Patents [OSTI]

    Banda, M.J.; Werb, Z.; Knighton, D.R.; Hunt, T.K.

    1985-03-05

    A nonmitogenic angiogenesis factor is isolated from wound fluid by dialysis to include materials in the molecular size range of 2,000 to 14,000, lyophilization, and chromatography. The nonmitogenic angiogenesis factor is identified by activity by corneal implant assay and by cell migration assay. The angiogenesis factor is also characterized by inactivity by mitogenesis assay. 3 figs.

  5. Bioorganometallic chemistry: biocatalytic oxidation reactions with biomimetic nad+/nadh co-factors and [cp*rh(bpy)h]+ for selective organic synthesis

    SciTech Connect (OSTI)

    Lutz, Jochen; Hollman, Frank; Ho, The Vinh; Schnyder, Adrian; Fish, Richard H.; Schmid, Andreas

    2004-03-09

    The biocatalytic, regioselective hydroxylation of 2-hydroxybiphenyl to the corresponding catechol was accomplished utilizing the monooxygenase 2-hydroxybiphenyl 3-monooxygenase (HbpA). The necessary natural nicotinamide adenine dinucleotide (NAD{sup +}) co-factor for this biocatalytic process was replaced by a biomimetic co-factor, N-benzylnicotinamide bromide, 1a. The interaction between the flavin (FAD) containing HbpA enzyme and the corresponding biomimetic NADH compound, N-benzyl-1,4-dihdronicotinamide, 1b, for hydride transfers, was shown to readily occur. The in situ recycling of the reduced NADH biomimic 1b from 1a was accomplished with [Cp*Rh(bpy)H](Cl); however, productive coupling of this regeneration reaction to the enzymatic hydroxylation reaction was not totally successful, due to a deactivation process concerning the HbpA enzyme peripheral groups; i.e., -SH or -NH{sub 2} possibly reacting with the precatalyst, [Cp*Rh(bpy)(H{sub 2}O)](Cl){sub 2}, and thus inhibiting the co-factor regeneration process. The deactivation mechanism was studied, and a promising strategy of derivatizing these peripheral -SH or -NH{sub 2} groups with a polymer containing epoxide was successful in circumventing the undesired interaction between HbpA and the precatalyst. This latter strategy allowed tandem co-factor regeneration using 1a or 2a, [Cp*Rh(bpy)(H2O)](Cl){sub 2}, and formate ion, in conjunction with the polymer bound, FAD containing HbpA enzyme to provide the catechol product.

  6. Factors governing sustainable groundwater pumping near a river

    SciTech Connect (OSTI)

    Zhang, Y.; Hubbard, S.S.; Finsterle, S.

    2011-01-15

    The objective of this paper is to provide new insights into processes affecting riverbank filtration (RBF). We consider a system with an inflatable dam installed for enhancing water production from downstream collector wells. Using a numerical model, we investigate the impact of groundwater pumping and dam operation on the hydrodynamics in the aquifer and water production. We focus our study on two processes that potentially limit water production of an RBF system: the development of an unsaturated zone and riverbed clogging. We quantify river clogging by calibrating a time-dependent riverbed permeability function based on knowledge of pumping rate, river stage, and temperature. The dynamics of the estimated riverbed permeability reflects clogging and scouring mechanisms. Our results indicate that (1) riverbed permeability is the dominant factor affecting infiltration needed for sustainable RBF production; (2) dam operation can influence pumping efficiency and prevent the development of an unsaturated zone beneath the riverbed only under conditions of sufficient riverbed permeability; (3) slow river velocity, caused by dam raising during summer months, may lead to sedimentation and deposition of fine-grained material within the riverbed, which may clog the riverbed, limiting recharge to the collector wells and contributing to the development of an unsaturated zone beneath the riverbed; and (4) higher river flow velocities, caused by dam lowering during winter storms, scour the riverbed an thus increase its permeability. These insights can be used as the basis for developing sustainable water management of a RBF system.

  7. Hyperdynamics boost factor achievable with an ideal bias potential

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Huang, Chen; Perez, Danny; Voter, Arthur F.

    2015-08-20

    Hyperdynamics is a powerful method to significantly extend the time scales amenable to molecular dynamics simulation of infrequent events. One outstanding challenge, however, is the development of the so-called bias potential required by the method. In this work, we design a bias potential using information about all minimum energy pathways (MEPs) out of the current state. While this approach is not suitable for use in an actual hyperdynamics simulation, because the pathways are generally not known in advance, it allows us to show that it is possible to come very close to the theoretical boost limit of hyperdynamics while maintainingmore » high accuracy. We demonstrate this by applying this MEP-based hyperdynamics (MEP-HD) to metallic surface diffusion systems. In most cases, MEP-HD gives boost factors that are orders of magnitude larger than the best existing bias potential, indicating that further development of hyperdynamics bias potentials could have a significant payoff. Lastly, we discuss potential practical uses of MEP-HD, including the possibility of developing MEP-HD into a true hyperdynamics.« less

  8. Factors affecting coking pressures in tall coke ovens

    SciTech Connect (OSTI)

    Grimley, J.J.; Radley, C.E.

    1995-12-01

    The detrimental effects of excessive coking pressures, resulting in the permanent deformation of coke oven walls, have been recognized for many years. Considerable research has been undertaken worldwide in attempts to define the limits within which a plant may safely operate and to quantify the factors which influence these pressures. Few full scale techniques are available for assessing the potential of a coal blend for causing wall damage. Inference of dangerous swelling pressures may be made however by the measurement of the peak gas pressure which is generated as the plastic layers meet and coalesce at the center of the oven. This pressure is referred to in this report as the carbonizing pressure. At the Dawes Lane cokemaking plant of British Steel`s Scunthorpe Works, a large database has been compiled over several years from the regulator measurement of this pressure. This data has been statistically analyzed to provide a mathematical model for predicting the carbonizing pressure from the properties of the component coals, the results of this analysis are presented in this report.

  9. Major Risk Factors Integrated Facility Disposition Project - Oak Ridge

    Office of Environmental Management (EM)

    D D e e p p a a r r t t m m e e n n t t o o f f E E n n e e r r g g y y O O f f f f i i c c e e o o f f E E n n v v i i r r o o n n m m e e n n t t a a l l M M a a n n a a g g e e m m e e n n t t ( ( E E M M ) ) E E n n g g i i n n e e e e r r i i n n g g a a n n d d T T e e c c h h n n o o l l o o g g y y External Technical Review (ETR) Report Major Risk Factors Integrated Facility Disposition Project (IFDP) Oak Ridge, TN AUGUST 1, 2008 Acknowledgement The External Technical Review of the

  10. Factors influencing radiation therapy student clinical placement satisfaction

    SciTech Connect (OSTI)

    Bridge, Pete; Carmichael, Mary-Ann

    2014-02-15

    Introduction: Radiation therapy students at Queensland University of Technology (QUT) attend clinical placements at five different clinical departments with varying resources and support strategies. This study aimed to determine the relative availability and perceived importance of different factors affecting student support while on clinical placement. The purpose of the research was to inform development of future support mechanisms to enhance radiation therapy students’ experience on clinical placement. Methods: This study used anonymous Likert-style surveys to gather data from years 1 and 2 radiation therapy students from QUT and clinical educators from Queensland relating to availability and importance of support mechanisms during clinical placements in a semester. Results: The study findings demonstrated student satisfaction with clinical support and suggested that level of support on placement influenced student employment choices. Staff support was perceived as more important than physical resources; particularly access to a named mentor, a clinical educator and weekly formative feedback. Both students and educators highlighted the impact of time pressures. Conclusions: The support offered to radiation therapy students by clinical staff is more highly valued than physical resources or models of placement support. Protected time and acknowledgement of the importance of clinical education roles are both invaluable. Joint investment in mentor support by both universities and clinical departments is crucial for facilitation of effective clinical learning.

  11. Highly Efficient Small Form Factor LED Retrofit Lamp

    SciTech Connect (OSTI)

    Steven Allen; Fred Palmer; Ming Li

    2011-09-11

    This report summarizes work to develop a high efficiency LED-based MR16 lamp downlight at OSRAM SYLVANIA under US Department of Energy contract DE-EE0000611. A new multichip LED package, electronic driver, and reflector optic were developed for these lamps. At steady-state, the lamp luminous flux was 409 lumens (lm), luminous efficacy of 87 lumens per watt (LPW), CRI (Ra) of 87, and R9 of 85 at a correlated color temperature (CCT) of 3285K. The LED alone achieved 120 lumens per watt efficacy and 600 lumen flux output at 25 C. The driver had 90% electrical conversion efficiency while maintaining excellent power quality with power factor >0.90 at a power of only 5 watts. Compared to similar existing MR16 lamps using LED sources, these lamps had much higher efficacy and color quality. The objective of this work was to demonstrate a LED-based MR16 retrofit lamp for replacement of 35W halogen MR16 lamps having (1) luminous flux of 500 lumens, (2) luminous efficacy of 100 lumens per watt, (3) beam angle less than 40{sup o} and center beam candlepower of at least 1000 candelas, and (4) excellent color quality.

  12. Factors controlling pathogen destruction during anaerobic digestion of biowastes

    SciTech Connect (OSTI)

    Smith, S.R. . E-mail: s.r.smith@imperial.ac.uk; Lang, N.L.; Cheung, K.H.M.; Spanoudaki, K.

    2005-07-01

    Anaerobic digestion is the principal method of stabilising biosolids from urban wastewater treatment in the UK, and it also has application for the treatment of other types of biowaste. Increasing awareness of the potential risks to human and animal health from environmental sources of pathogens has focused attention on the efficacy of waste treatment processes at destroying pathogenic microorganisms in biowastes recycled to agricultural land. The degree of disinfection achieved by a particular anaerobic digester is influenced by a variety of interacting operational variables and conditions, which can often deviate from the ideal. Experimental investigations demonstrate that Escherichia coli and Salmonella spp. are not damaged by mesophilic temperatures, whereas rapid inactivation occurs by thermophilic digestion. A hydraulic, biokinetic and thermodynamic model of pathogen inactivation during anaerobic digestion showed that a 2 log{sub 10} reduction in E. coli (the minimum removal required for agricultural use of conventionally treated biosolids) is likely to challenge most conventional mesophilic digesters, unless strict maintenance and management practices are adopted to minimise dead zones and by-pass flow. Efficient mixing and organic matter stabilisation are the main factors controlling the rate of inactivation under mesophilic conditions and not a direct effect of temperature per se on pathogenic organisms.

  13. State-level Greenhouse Gas Emission Factors for Electricity Generation, Updated 2002

    Reports and Publications (EIA)

    2002-01-01

    This report documents the preparation of updated state-level electricity coefficients for carbon dioxide (CO ), methane (CH ), and nitrous oxide (NO), which represent a three-year weighted average for 1998-2000.

  14. Applying Human Factors during the SIS Life Cycle

    SciTech Connect (OSTI)

    Avery, K.

    2010-05-05

    Safety Instrumented Systems (SIS) are widely used in U.S. Department of Energy's (DOE) nonreactor nuclear facilities for safety-critical applications. Although use of the SIS technology and computer-based digital controls, can improve performance and safety, it potentially introduces additional complexities, such as failure modes that are not readily detectable. Either automated actions or manual (operator) actions may be required to complete the safety instrumented function to place the process in a safe state or mitigate a hazard in response to an alarm or indication. DOE will issue a new standard, Application of Safety Instrumented Systems Used at DOE Nonreactor Nuclear Facilities, to provide guidance for the design, procurement, installation, testing, maintenance, operation, and quality assurance of SIS used in safety significant functions at DOE nonreactor nuclear facilities. The DOE standard focuses on utilizing the process industry consensus standard, American National Standards Institute/ International Society of Automation (ANSI/ISA) 84.00.01, Functional Safety: Safety Instrumented Systems for the Process Industry Sector, to support reliable SIS design throughout the DOE complex. SIS design must take into account human-machine interfaces and their limitations and follow good human factors engineering (HFE) practices. HFE encompasses many diverse areas (e.g., information display, user-system interaction, alarm management, operator response, control room design, and system maintainability), which affect all aspects of system development and modification. This paper presents how the HFE processes and principles apply throughout the SIS life cycle to support the design and use of SIS at DOE nonreactor nuclear facilities.

  15. Multifocal Glioblastoma Multiforme: Prognostic Factors and Patterns of Progression

    SciTech Connect (OSTI)

    Showalter, Timothy N.; Andrel, Jocelyn; Andrews, David W.; Curran, Walter J.; Daskalakis, Constantine; Werner-Wasik, Maria

    2007-11-01

    Purpose: To assess the progression patterns in patients with multifocal glioblastoma multiforme who had undergone whole brain radiotherapy (WBRT), the historical standard, versus three-dimensional conformal radiotherapy, and to identify predictive treatment and pretreatment factors. Methods and Materials: The records of 50 patients with multifocal glioblastoma multiforme treated with RT were reviewed. Univariate analyses were performed using survival methods and the Cox proportional hazards regression method. Multivariate analyses were performed using the Cox proportional hazards regression method. Results: The mean age was 61 years, and 71% had a Karnofsky performance status (KPS) score of {>=}70. Of the 50 patients, 32% underwent WBRT and 68%, three-dimensional conformal RT. Progression was local in all evaluable patients, as determined by imaging in 38 patients and early neurologic progression in 12. The median time to progression (TTP) was 3.1 months, and the median survival time (MST) was 8.1 months. The significant independent predictors of TTP on multivariate analysis were a KPS score <70 (p = 0.001), the extent of surgery (p = 0.040), a radiation dose <60 Gy (p = 0.027), and the lack of chemotherapy (p = 0.001). The significant independent predictors of a reduced MST were a KPS score <70 (p = 0.022) and the absence of salvage surgery (p = 0.011) and salvage chemotherapy (p = 0.003). Conclusion: Local progression was observed in all patients. On multivariate analysis, no significant difference was found in the TTP or MST between three-dimensional conformal radiotherapy and WBRT. The KPS was a consistent independent predictor of both TTP and MST. On the basis of the progression pattern, we do not recommend WBRT as a mandatory component of the treatment of multifocal glioblastoma multi0011for.

  16. Impact of HFIR LEU Conversion on Beryllium Reflector Degradation Factors

    SciTech Connect (OSTI)

    Ilas, Dan

    2013-10-01

    An assessment of the impact of low enriched uranium (LEU) conversion on the factors that may cause the degradation of the beryllium reflector is performed for the High Flux Isotope Reactor (HFIR). The computational methods, models, and tools, comparisons with previous work, along with the results obtained are documented and discussed in this report. The report documents the results for the gas and neutronic poison production, and the heating in the beryllium reflector for both the highly enriched uranium (HEU) and LEU HFIR configurations, and discusses the impact that the conversion to LEU may have on these quantities. A time-averaging procedure was developed to calculate the isotopic (gas and poisons) production in reflector. The sensitivity of this approach to different approximations is gauged and documented. The results show that the gas is produced in the beryllium reflector at a total rate of 0.304 g/cycle for the HEU configuration; this rate increases by ~12% for the LEU case. The total tritium production rate in reflector is 0.098 g/cycle for the HEU core and approximately 11% higher for the LEU core. A significant increase (up to ~25%) in the neutronic poisons production in the reflector during the operation cycles is observed for the LEU core, compared to the HEU case, for regions close to the core s horizontal midplane. The poisoning level of the reflector may increase by more than two orders of magnitude during long periods of downtime. The heating rate in the reflector is estimated to be approximately 20% lower for the LEU core than for the HEU core. The decrease is due to a significantly lower contribution of the heating produced by the gamma radiation for the LEU core. Both the isotopic (gas and neutronic poisons) production and the heating rates are spatially non-uniform throughout the beryllium reflector volume. The maximum values typically occur in the removable reflector and close to the midplane.

  17. Human Factors Considerations in New Nuclear Power Plants: Detailed Analysis.

    SciTech Connect (OSTI)

    OHara,J.; Higgins, J.; Brown, W.; Fink, R.

    2008-02-14

    This Nuclear Regulatory Commission (NRC) sponsored study has identified human-performance issues in new and advanced nuclear power plants. To identify the issues, current industry developments and trends were evaluated in the areas of reactor technology, instrumentation and control technology, human-system integration technology, and human factors engineering (HFE) methods and tools. The issues were organized into seven high-level HFE topic areas: Role of Personnel and Automation, Staffing and Training, Normal Operations Management, Disturbance and Emergency Management, Maintenance and Change Management, Plant Design and Construction, and HFE Methods and Tools. The issues where then prioritized into four categories using a 'Phenomena Identification and Ranking Table' methodology based on evaluations provided by 14 independent subject matter experts. The subject matter experts were knowledgeable in a variety of disciplines. Vendors, utilities, research organizations and regulators all participated. Twenty issues were categorized into the top priority category. This Brookhaven National Laboratory (BNL) technical report provides the detailed methodology, issue analysis, and results. A summary of the results of this study can be found in NUREG/CR-6947. The research performed for this project has identified a large number of human-performance issues for new control stations and new nuclear power plant designs. The information gathered in this project can serve as input to the development of a long-term strategy and plan for addressing human performance in these areas through regulatory research. Addressing human-performance issues will provide the technical basis from which regulatory review guidance can be developed to meet these challenges. The availability of this review guidance will help set clear expectations for how the NRC staff will evaluate new designs, reduce regulatory uncertainty, and provide a well-defined path to new nuclear power plant licensing.

  18. Coupling field and laboratory measurements to estimate the emission factors of identified and unidentified trace gases for prescribed fires

    SciTech Connect (OSTI)

    Yokelson, Robert J.; Burling, Ian R.; Gilman, Jessica; Warneke, Carsten; Stockwell, Chelsea E.; de Gouw, Joost A.; Akagi, Sheryl; Urbanski, Shawn; Veres, Patrick; Roberts, James M.; Kuster, W. C.; Reardon, James; Griffith, David WT; Johnson, Timothy J.; Hosseini, SeyedEhsan; Miller, J. Wayne; Cocker, David R.; Jung, H.; Weise, David

    2013-01-07

    Vegetative fuels commonly consumed in prescribed fires were collected from five locations in the southeastern and southwestern U.S. and burned in a series of 77 fires at the U.S. Forest Service Fire Sciences Laboratory in Missoula, Montana. The particulate matter (PM2.5) emissions were measured by gravimetric filter sampling with subsequent analysis for elemental carbon (EC), organic carbon (OC), and 38 elements. The trace gas emissions were measured with a large suite of state-of-the-art instrumentation including an open-path Fourier transform infrared (OP FTIR) spectrometer, proton-transfer-reaction mass spectrometry (PTR-MS), proton-transfer ion-trap mass spectrometry (PIT-MS), negative-ion proton-transfer chemical-ionization mass spectrometry (NI-PT-CIMS), and gas chromatography with MS detection (GC-MS). 204 trace gas species (mostly non-methane organic compounds (NMOC)) were identified and quantified with the above instruments. An additional 152 significant peaks in the unit mass resolution mass spectra were quantified, but either could not be identified or most of the signal at that molecular mass was unaccounted for by identifiable species. As phase II of this study, we conducted airborne and ground-based sampling of the emissions from real prescribed fires mostly in the same land management units where the fuels for the lab fires were collected. A broad variety, but smaller number of species (21 trace gas species and PM2.5) was measured on 14 fires in chaparral and oak savanna in the southwestern US, as well as pine forest understory in the southeastern US and Sierra Nevada mountains of California. These extensive field measurements of emission factors (EF) for temperate biomass burning are useful both for modeling and to examine the representativeness of our lab fire EF. The lab/field EF ratio for the pine understory fuels was not statistically different from one, on average. However, our lab EF for “smoldering compounds” emitted by burning the semi-arid SW fuels should likely be increased by about a factor of 2.7 to better represent field fires. Based on the lab/field comparison, we present a table with emission factors for 365 pyrogenic species (including unidentified species) for 4 broad fuel types: pine understory, semi-arid shrublands, evergreen canopy, and duff. To our knowledge this is the most complete measurement of biomass burning emissions to date and it should enable improved representation of smoke in atmospheric models. The results provide important insights into the nature of smoke. For example, ~35% (range from 16-71%) of the mass of gas-phase NMOC species was attributed to the species that we could not identify. These unidentified species are likely not represented in most models, but some provision should be made for the fact that they will react in the atmosphere. In addition, the total mass of gas-phase NMOC divided by the mass of co-emitted PM2.5 averaged ~2.6 for the main fire types with a range from ~1.8-8.8. About 36-63% of the NMOC were likely semivolatile or of intermediate volatility. Thus, the gas-phase NMOC represent a large reservoir of potential precursors for secondary formation of organic aerosol. For the one fire in organic soil (Alaskan duff) about 28% of the emitted carbon was present as gas-phase NMOC in contrast to the other fuels for which NMOC accounted for only ~1-3% of emitted carbon. 71% of the mass of NMOC emitted by the smoldering duff was un-identified. The duff results highlight the need to learn more about the emissions from smoldering organic soils. The ?NMOC/“NOx-as-NO” ratio was consistently about ten for the main fire types when accounting for all NMOC, indicating strongly NOx-limited O3 production conditions. Finally, the fuel consumption per unit area was measured on 6 of the 14 prescribed fires and averaged 7.08 ± 2.09 (1?) Mg ha-1.

  19. Economic Conditions and Factors Affecting New Nuclear Power Deployment

    SciTech Connect (OSTI)

    Harrison, Thomas J.

    2014-10-01

    This report documents work performed in support of the US Department of Energy Office of Nuclear Energy’s Advanced Small Modular Reactor (AdvSMR) program. The report presents information and results from economic analyses to describe current electricity market conditions and those key factors that may impact the deployment of AdvSMRs or any other new nuclear power plants. Thus, this report serves as a reference document for DOE as it moves forward with its plans to develop advanced reactors, including AdvSMRs. For the purpose of this analysis, information on electricity markets and nuclear power plant operating costs will be combined to examine the current state of the nuclear industry and the process required to successfully move forward with new nuclear power in general and AdvSMRs in particular. The current electricity market is generally unfavorable to new nuclear construction, especially in deregulated markets with heavy competition from natural gas and subsidized renewables. The successful and profitable operation of a nuclear power plant (or any power plant) requires the rate at which the electricity is sold to be sufficiently greater than the cost to operate. The wholesale rates in most US markets have settled into values that provide profits for most operating nuclear power plants but are too low to support the added cost of capital recovery for new nuclear construction. There is a strong geographic dependence on the wholesale rate, with some markets currently able to support new nuclear construction. However, there is also a strong geographic dependence on pronuclear public opinion; the areas where power prices are high tend to have unfavorable views on the construction of new nuclear power plants. The use of government-backed incentives, such as subsidies, can help provide a margin to help justify construction projects that otherwise may not seem viable. Similarly, low interest rates for the project will also add a positive margin to the economic analysis. In both cases, the profitable price point is decreased, making more markets open to profitable entry. Overall, the economic attractiveness of a nuclear power construction project is not only a function of its own costs, but a function of the market into which it is deployed. Many of the market characteristics are out of the control of the potential nuclear power plant operators. The decision-making process for the power industry in general is complicated by the short-term market volatility in both the wholesale electricity market and the commodity (natural gas) market. Decisions based on market conditions today may be rendered null and void in six months. With a multiple-year lead time, nuclear power plants are acutely vulnerable to market corrections.

  20. Key Response Planning Factors for the Aftermath of Nuclear Terrorism

    SciTech Connect (OSTI)

    Buddemeier, B R; Dillon, M B

    2009-01-21

    Despite hundreds of above-ground nuclear tests and data gathered from Hiroshima and Nagasaki, the effects of a ground-level, low-yield nuclear detonation in a modern urban environment are still the subject of considerable scientific debate. Extensive review of nuclear weapon effects studies and discussions with nuclear weapon effects experts from various federal agencies, national laboratories, and technical organizations have identified key issues and bounded some of the unknowns required to support response planning for a low-yield, ground-level nuclear detonation in a modern U.S. city. This study, which is focused primarily upon the hazards posed by radioactive fallout, used detailed fallout predictions from the advanced suite of three-dimensional (3-D) meteorology and plume/fallout models developed at Lawrence Livermore National Laboratory (LLNL), including extensive global Key Response Planning Factors for the Aftermath of Nuclear Terrorism geographical and real-time meteorological databases to support model calculations. This 3-D modeling system provides detailed simulations that account for complex meteorology and terrain effects. The results of initial modeling and analysis were presented to federal, state, and local working groups to obtain critical, broad-based review and feedback on strategy and messaging. This effort involved a diverse set of communities, including New York City, National Capitol Regions, Charlotte, Houston, Portland, and Los Angeles. The largest potential for reducing casualties during the post-detonation response phase comes from reducing exposure to fallout radiation. This can be accomplished through early, adequate sheltering followed by informed, delayed evacuation.B The response challenges to a nuclear detonation must be solved through multiple approaches of public education, planning, and rapid response actions. Because the successful response will require extensive coordination of a large number of organizations, supplemented by appropriate responses by local responders and the general population within the hazard zones, regional planning is essential to success. The remainder of this Executive Summary provides summary guidance for response planning in three areas: (1) Public Protection Strategy details the importance of early, adequate shelter followed by informed evacuation. (2) Responder Priorities identify how to protect response personnel, perform regional situational assessment, and support public safety. (3) Key Planning Considerations refute common myths and provide important information on planning how to respond in the aftermath of nuclear terrorism.

  1. Closer to HIV vaccine goal with new insight into viral factors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Closer to HIV vaccine goal with new insight into viral factors New insight into viral factors that facilitate HIV transmission Understanding viral factors that facilitate transmission of HIV infection is critical to developing vaccines. February 14, 2012 Scientists work at the National Stable Isotope Resource LANL scientists found that the infected donor's predominant virus subpopulation in the genital tract differed from that in the blood. Comparing the HIV sequence population in each newly

  2. Using Two-Factor RSA Token with WebVPN | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Using Two-Factor RSA Token with WebVPN Using Two-Factor RSA Token with WebVPN Your RSA token is used to esbablish a connection to the Internet and connect to https://connect.doe.gov . PDF icon Using-TwoFactorRSA-Token w VPN.pdf More Documents & Publications Instructions for WebVPN Connectivity Citrix_2FA_Authentication_09.09 Microsoft Word - Citrix_2FA_Authentication_12_3_2009.doc

  3. Landslide hazard mapping with selected dominant factors: A study case of Penang Island, Malaysia

    SciTech Connect (OSTI)

    Tay, Lea Tien; Alkhasawneh, Mutasem Sh.; Ngah, Umi Kalthum; Lateh, Habibah

    2015-05-15

    Landslide is one of the destructive natural geohazards in Malaysia. In addition to rainfall as triggering factos for landslide in Malaysia, topographical and geological factors play important role in the landslide susceptibility analysis. Conventional topographic factors such as elevation, slope angle, slope aspect, plan curvature and profile curvature have been considered as landslide causative factors in many research works. However, other topographic factors such as diagonal length, surface area, surface roughness and rugosity have not been considered, especially for the research work in landslide hazard analysis in Malaysia. This paper presents landslide hazard mapping using Frequency Ratio (FR) and the study area is Penang Island of Malaysia. Frequency ratio approach is a variant of probabilistic method that is based on the observed relationships between the distribution of landslides and each landslide-causative factor. Landslide hazard map of Penang Island is produced by considering twenty-two (22) landslide causative factors. Among these twenty-two (22) factors, fourteen (14) factors are topographic factors. They are elevation, slope gradient, slope aspect, plan curvature, profile curvature, general curvature, tangential curvature, longitudinal curvature, cross section curvature, total curvature, diagonal length, surface area, surface roughness and rugosity. These topographic factors are extracted from the digital elevation model of Penang Island. The other eight (8) non-topographic factors considered are land cover, vegetation cover, distance from road, distance from stream, distance from fault line, geology, soil texture and rainfall precipitation. After considering all twenty-two factors for landslide hazard mapping, the analysis is repeated with fourteen dominant factors which are selected from the twenty-two factors. Landslide hazard map was segregated into four categories of risks, i.e. Highly hazardous area, Hazardous area, Moderately hazardous area and Not hazardous area. The maps was assessed using ROC (Rate of Curve) based on the area under the curve method (AUC). The result indicates an increase of accuracy from 77.76% (with all 22 factors) to 79.00% (with 14 dominant factors) in the prediction of landslide occurrence.

  4. Influence of graphene on quality factor variation in a silicon ring resonator

    SciTech Connect (OSTI)

    Kou, Rai; Tanabe, Shinichi; Hibino, Hiroki; Tsuchizawa, Tai; Yamada, Koji; Yamamoto, Tsuyoshi; Nakajima, Hirochika

    2014-03-03

    Selectively patterned graphene is integrated onto a silicon ring resonator to investigate the quality factor (Q factor) variation. The Q factor sharply decreases from 7900 to 1200 as the patterned graphene length increases from 0 to 20??m. A numerical estimation, which takes into account optical absorption by graphene, shows an exponential damping of the Q factor with increasing graphene length and is consistent with the experimental result. We expect these fundamental characterizations to be helpful in developing graphene-integrated silicon photonics applications.

  5. Inhibition of B-NHEJ in Plateau-Phase Cells Is Not a Direct Consequence of Suppressed Growth Factor Signaling

    SciTech Connect (OSTI)

    Singh, Satyendra K.; Bednar, Theresa; Zhang Lihua; Wu, Wenqi; Mladenov, Emil; Iliakis, George

    2012-10-01

    Purpose: It has long been known that the proliferation status of a cell is a determinant of radiation response, and the available evidence implicates repair of DNA double-strand breaks (DSBs) in the underlying mechanism. Recent results have shown that a novel, highly error-prone pathway of nonhomologous end joining (NHEJ) operating as backup (B-NHEJ) processes DSBs in irradiated cells when the canonical, DNA-PK (DNA-dependent protein kinase)-dependent pathway of NHEJ (D-NHEJ) is compromised. Notably, B-NHEJ shows marked reduction in efficiency when D-NHEJ-deficient cells cease to grow and enter a plateau phase. This phenomenon is widespread and observed in cells of different species with defects in core components of D-NHEJ, with the notable exception of DNA-PKcs (DNA-dependent protein kinase, catalytic subunit). Using new, standardized serum-deprivation protocols, we re-examine the growth requirements of B-NHEJ and test the role of epidermal growth factor receptor (EGFR) signaling in its regulation. Methods and Materials: DSB repair was measured by pulsed-field gel electrophoresis in cells maintained under different conditions of growth. Results: Serum deprivation in D-NHEJ-deficient cells causes a rapid reduction in B-NHEJ similar to that measured in normally growing cells that enter the plateau phase of growth. Upon serum deprivation, reduction in B-NHEJ activity is evident at 4 h and reaches a plateau reflecting maximum inhibition at 12-16 h. The inhibition is reversible, and B-NHEJ quickly recovers to the levels of actively growing cells upon supply of serum to serum-deprived cells. Chemical inhibition of EGFR in proliferating cells inhibits only marginally B-NHEJ and addition of EGFR in serum-deprived cells increases only a marginally B-NHEJ. Conclusions: The results document a rapid and fully reversible adaptation of B-NHEJ to growth activity and point to factors beyond EGFR in its regulation. They show notable differences in the regulation of error-prone DSB repair pathways between proliferating and non proliferating cells that may present new treatment design opportunities in radiation therapy.

  6. First Evaluation of the Biologic Effectiveness Factors of Boron Neutron Capture Therapy (BNCT) in a Human Colon Carcinoma Cell Line

    SciTech Connect (OSTI)

    Dagrosa, Maria Alejandra; Crivello, Martin; Perona, Marina; Thorp, Silvia; Santa Cruz, Gustavo Alberto; Pozzi, Emiliano; Casal, Mariana; Thomasz, Lisa; Cabrini, Romulo; Kahl, Steven; Juvenal, Guillermo Juan; Pisarev, Mario Alberto

    2011-01-01

    Purpose: DNA lesions produced by boron neutron capture therapy (BNCT) and those produced by gamma radiation in a colon carcinoma cell line were analyzed. We have also derived the relative biologic effectiveness factor (RBE) of the neutron beam of the RA-3- Argentine nuclear reactor, and the compound biologic effectiveness (CBE) values for p-boronophenylalanine ({sup 10}BPA) and for 2,4-bis ({alpha},{beta}-dihydroxyethyl)-deutero-porphyrin IX ({sup 10}BOPP). Methods and Materials: Exponentially growing human colon carcinoma cells (ARO81-1) were distributed into the following groups: (1) BPA (10 ppm {sup 10}B) + neutrons, (2) BOPP (10 ppm {sup 10}B) + neutrons, (3) neutrons alone, and (4) gamma rays ({sup 60}Co source at 1 Gy/min dose-rate). Different irradiation times were used to obtain total absorbed doses between 0.3 and 5 Gy ({+-}10%) (thermal neutrons flux = 7.5 10{sup 9} n/cm{sup 2} sec). Results: The frequency of micronucleated binucleated cells and the number of micronuclei per micronucleated binucleated cells showed a dose-dependent increase until approximately 2 Gy. The response to gamma rays was significantly lower than the response to the other treatments (p < 0.05). The irradiations with neutrons alone and neutrons + BOPP showed curves that did not differ significantly from, and showed less DNA damage than, irradiation with neutrons + BPA. A decrease in the surviving fraction measured by 3-(4,5-dimetiltiazol-2-il)-2,5-difeniltetrazolium bromide (MTT) assay as a function of the absorbed dose was observed for all the treatments. The RBE and CBE factors calculated from cytokinesis block micronucleus (CBMN) and MTT assays were, respectively, the following: beam RBE: 4.4 {+-} 1.1 and 2.4 {+-} 0.6; CBE for BOPP: 8.0 {+-} 2.2 and 2.0 {+-} 1; CBE for BPA: 19.6 {+-} 3.7 and 3.5 {+-} 1.3. Conclusions: BNCT and gamma irradiations showed different genotoxic patterns. To our knowledge, these values represent the first experimental ones obtained for the RA-3 in a biologic model and could be useful for future experimental studies for the application of BNCT to colon carcinoma.

  7. Insights into the Molecular Activation Mechanism of the RhoA-specific Guanine Nucleotide Exchange Factor, PDZRhoGEF

    SciTech Connect (OSTI)

    Bielnicki, Jakub A.; Shkumatov, Alexander V.; Derewenda, Urszula; Somlyo, Avril V.; Svergun, Dmitri I.; Derewenda, Zygmunt S.

    2012-10-09

    PDZRhoGEF (PRG) belongs to a small family of RhoA-specific nucleotide exchange factors that mediates signaling through select G-protein-coupled receptors via G{alpha}{sub 12/13} and activates RhoA by catalyzing the exchange of GDP to GTP. PRG is a multidomain protein composed of PDZ, regulators of G-protein signaling-like (RGSL), Dbl-homology (DH), and pleckstrin-homology (PH) domains. It is autoinhibited in cytosol and is believed to undergo a conformational rearrangement and translocation to the membrane for full activation, although the molecular details of the regulation mechanism are not clear. It has been shown recently that the main autoregulatory elements of PDZRhoGEF, the autoinhibitory 'activation box' and the 'GEF switch,' which is required for full activation, are located directly upstream of the catalytic DH domain and its RhoA binding surface, emphasizing the functional role of the RGSL-DH linker. Here, using a combination of biophysical and biochemical methods, we show that the mechanism of PRG regulation is yet more complex and may involve an additional autoinhibitory element in the form of a molten globule region within the linker between RGSL and DH domains. We propose a novel, two-tier model of autoinhibition where the activation box and the molten globule region act synergistically to impair the ability of RhoA to bind to the catalytic DH-PH tandem. The molten globule region and the activation box become less ordered in the PRG-RhoA complex and dissociate from the RhoA-binding site, which may constitute a critical step leading to PRG activation.

  8. Microstructure factor and mechanical and electronic properties of hydrogenated amorphous and nanocrystalline silicon thin-films for microelectromechanical systems applications

    SciTech Connect (OSTI)

    Mouro, J.; Gualdino, A.; Chu, V. [Instituto de Engenharia de Sistemas e Computadores – Microsistemas e Nanotecnologias (INESC-MN) and IN – Institute of Nanoscience and Nanotechnology, 1000-029 Lisbon (Portugal); Conde, J. P. [Instituto de Engenharia de Sistemas e Computadores – Microsistemas e Nanotecnologias (INESC-MN) and IN – Institute of Nanoscience and Nanotechnology, 1000-029 Lisbon (Portugal); Department of Bioengineering, Instituto Superior Técnico (IST), 1049-001 Lisbon (Portugal)

    2013-11-14

    Thin-film silicon allows the fabrication of MEMS devices at low processing temperatures, compatible with monolithic integration in advanced electronic circuits, on large-area, low-cost, and flexible substrates. The most relevant thin-film properties for applications as MEMS structural layers are the deposition rate, electrical conductivity, and mechanical stress. In this work, n{sup +}-type doped hydrogenated amorphous and nanocrystalline silicon thin-films were deposited by RF-PECVD, and the influence of the hydrogen dilution in the reactive mixture, the RF-power coupled to the plasma, the substrate temperature, and the deposition pressure on the structural, electrical, and mechanical properties of the films was studied. Three different types of silicon films were identified, corresponding to three internal structures: (i) porous amorphous silicon, deposited at high rates and presenting tensile mechanical stress and low electrical conductivity, (ii) dense amorphous silicon, deposited at intermediate rates and presenting compressive mechanical stress and higher values of electrical conductivity, and (iii) nanocrystalline silicon, deposited at very low rates and presenting the highest compressive mechanical stress and electrical conductivity. These results show the combinations of electromechanical material properties available in silicon thin-films and thus allow the optimized selection of a thin silicon film for a given MEMS application. Four representative silicon thin-films were chosen to be used as structural material of electrostatically actuated MEMS microresonators fabricated by surface micromachining. The effect of the mechanical stress of the structural layer was observed to have a great impact on the device resonance frequency, quality factor, and actuation force.

  9. Sci—Fri AM: Mountain — 01: Validation of a new formulism and the related correction factors on output factor determination for small photon fields

    SciTech Connect (OSTI)

    Wang, Yizhen; Younge, Kelly; Nielsen, Michelle; Mutanga, Theodore; Cui, Congwu; Das, Indra J.

    2014-08-15

    Small field dosimetry measurements including output factors are difficult due to lack of charged-particle equilibrium, occlusion of the radiation source, the finite size of detectors, and non-water equivalence of detector components. With available detectors significant variations could be measured that will lead to incorrect delivered dose to patients. IAEA/AAPM have provided a framework and formulation to correct the detector response in small photon fields. Monte Carlo derived correction factors for some commonly used small field detectors are now available, however validation has not been performed prior to this study. An Exradin A16 chamber, EDGE detector and SFD detector were used to perform the output factor measurement for a series of conical fields (5–30mm) on a Varian iX linear accelerator. Discrepancies up to 20%, 10% and 6% were observed for 5, 7.5 and 10 mm cones between the initial output factors measured by the EDGE detector and the A16 ion chamber, while the discrepancies for the conical fields larger than 10 mm were less than 4%. After the application of the correction, the output factors agree well with each other to within 1%. Caution is needed when determining the output factors for small photon fields, especially for fields 10 mm in diameter or smaller. More than one type of detector should be used, each with proper corrections applied to the measurement results. It is concluded that with the application of correction factors to appropriately chosen detectors, output can be measured accurately for small fields.

  10. Development of adjustment factors for the EPA city and highway MPG values

    SciTech Connect (OSTI)

    Hellman, K.H.; Murrell, J.D.

    1984-01-01

    This paper describes the development of adjustment factors applicable to the EPA City and Highway MPG values. The paper discusses the data bases used, and the analytical methods employed to arrive at adjustment factors of 0.90 for the EPA City MPG value and 0.78 for the EPA Highway MPG value.

  11. Consideration of factors affecting strip effluent pH and sodium content

    SciTech Connect (OSTI)

    Peters, T. B.

    2015-07-29

    A number of factors were investigated to determine possible reasons for why the Strip Effluent (SE) can sometimes have higher than expected pH values and/or sodium content, both of which have prescribed limits. All of the factors likely have some impact on the pH values and Na content.

  12. Proton form factor ratio, {mu}{sub p}G{sub E}{sup P}/G{sub M}{sup P} from double spin asymmetry

    SciTech Connect (OSTI)

    Habarakada Liyanage, Anusha Pushpakumari

    2013-08-01

    The form factors are fundamental properties of the nucleon representing the effect of its structure on its response to electromagnetic probes such as electrons. They are functions of the four-momentum transfer squared Q{sup 2} between the electron and the proton. This thesis reports the results of a new measurement of the ratio of the electric and magnetic form factors of the proton up to Q{sup 2} = 5.66 (GeV/c){sup 2} using the double spin asymmetry with a polarized beam and target. Experiment E07-003 (SANE, Spin Asymmetries of the Nucleon Experiment) was carried out in Hall C at Jefferson Lab in 2009 to study the proton spin structure functions with a dynamically polarized ammonia target and longitudinally polarized electron beam. By detecting elastically scattered protons in the High-Momentum Spectrometer (HMS) in coincidence with the electrons in the Big Electron Telescope Array (BETA), elastic measurements were carried out in parallel. The elastic double spin asymmetry allows one to extract the proton electric to magnetic form factor ratio G{sup p}{sub E}/G{sup p}{sub M} at high-momentum transfer, Q{sup 2} = 5.66 (GeV/c){sup 2}. In addition to the coincidence data, inclusively scattered electrons from the polarized ammonia target were detected by HMS, which allows to measure the beam-target asymmetry in the elastic region with the target spin nearly perpendicular to the momentum transfer, and to extract G{sup p}{sub E}/G{sup p}{sub M} at low Q{sup 2} = 2.06 (GeV/c){sup 2}. This alternative measurement of G{sup p}{sub E}/G{sup p}{sub M} has verified and confirmed the dramatic discrepancy at high Q{sup 2} between the Rosenbluth and the recoil-polarization-transfer iv method with a different measurement technique and systematic uncertainties uncorrelated to those of the recoil-polarization measurements. The measurement of the form factor ratio at Q{sup 2} = 2.06 (GeV/c){sup 2} has been determined as {mu}{sub p}G{sup p}{sub E}/G{sup p}{sub M} = 0.605{+-}0.178{sub stat}{+-}0.033{sub sys} which is in agreement with an earlier measurement with the polarized target technique at similar kinematics. The measurement of the form factor ratio at Q{sup 2} = 5.66 (GeV/c){sup 2} has been determined as {mu}{sub p}G{sup p}{sub E}/G{sup p}{sub M} = 0.672 {+-} 0.362{sub stat} which represents the highest Q{sup 2} reach with the double spin asymmetry to date.

  13. H. R. 1271: A Bill to authorize appropriations for the Office of Environmental Quality for fiscal years 1992, 1993, 1994, 1995, and 1996; to ensure consideration of the impact of Federal actions on the global environment; and for other purposes, introduced in the House of Representatives, One Hundred Second Congress, First Session, March 5, 1991

    SciTech Connect (OSTI)

    Not Available

    1991-01-01

    This bill was introduced into the US House of Representatives on March 5, 1991 to amend the National Environmental Policy Act of 1969. The objective of the bill is to authorize appropriations for the Office of Environmental Quality for fiscal years 1992, 1993, 1994, 1995, and 1996. In addition, it will ensure consideration of the impact of federal actions on the global environment.

  14. H.R. 577: A Bill to amend the Internal Revenue Code of 1986 to provide a tax credit for the production of oil and gas from existing marginal oil and gas wells and from new oil and gas wells. Introduced in the House of Representatives, One Hundred Fourth Congress, First session

    SciTech Connect (OSTI)

    1995-12-31

    This document contains H.R. 577, A Bill to amend the Internal Revenue Code of 1986 to provide a tax credit for the production of oil and gas from existing marginal oil and gas wells and from new oil and gas wells. This Bill was introduced in the House of Representatives, 104th Congress, First Session, January 19, 1995.

  15. H. R. 4299: A bill to amend the Internal Revenue Code of 1986 in order to provide an incentive for business to invest in pollution abatement property and related assets, introduced in the US House of Representatives, One Hundred Second Congress, Second Session, February 25, 1992

    SciTech Connect (OSTI)

    Not Available

    1992-01-01

    This bill was introduced into the US House of Representatives on February 25, 1992 to amend the Internal Revenue Code of 1986 in order to provide an incentive for business to invest in pollution abatement property and related assets. This relates to a plant or other property in operation before January 1, 1991, to prevent, abate or control pollution.

  16. Expansion of X-ray form factor for close shell using uncorrelated wave function

    SciTech Connect (OSTI)

    AL-Robayi, Enas M.

    2013-12-16

    The atomic scattering factor has been studied for Be+ve, and B+2ve ions using the uncorrelated wave function (Hartree-Fock (HF)) for inter particle electronic shells. The physical importance of this factor appears in its relation to several important atomic properties as, the coherent scattering intensity, the total scattering intensity, the incoherent scattering function, the coherent scattering cross section, the total incoherent cross section, the nuclear magnetic shielding constant, the geometrical structure factor. Also there is one atomic properties the one particle radial density distribution function D(r)has been studied using the partitioning technique.

  17. JLab Measurement of the 4He Charge Form Factor at Large Momentum Transfers

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect SciTech Connect Search Results Journal Article: JLab Measurement of the 4He Charge Form Factor at Large Momentum Transfers Citation Details In-Document Search Title: JLab Measurement of the 4He Charge Form Factor at Large Momentum Transfers The charge form factor of 4He has been extracted in the range 29 fm-2 <= Q2 <= 77 fm-2 from elastic electron scattering, detecting 4He nuclei and electrons in coincidence with the High Resolution Spectrometers of

  18. Spatial correction factors for YALINA Booster facility loaded with medium and low enriched fuels

    SciTech Connect (OSTI)

    Talamo, A.; Gohar, Y. [Argonne National Laboratory, 9700 S. Cass Ave, Argonne, IL 60439 (United States); Bournos, V.; Fokov, Y.; Kiyavitskaya, H.; Routkovskaya, C. [Joint Inst. for Power and Nuclear Research-Sosny, 99 Academician A.K.Krasin Str, Minsk 220109 (Belarus)

    2012-07-01

    The Bell and Glasstone spatial correction factor is used in analyses of subcritical assemblies to correct the experimental reactivity as function of the detector position. Besides the detector position, several other parameters affect the correction factor: the energy weighting function of the detector, the detector size, the energy-angle distribution of source neutrons, and the reactivity of the subcritical assembly. This work focuses on the dependency of the correction factor on the detector material and it investigates the YALINA Booster subcritical assembly loaded with medium (36%) and low (10%) enriched fuels. (authors)

  19. g-factor anisotropy in nanowire-based InAs quantum dots

    SciTech Connect (OSTI)

    D'Hollosy, Samuel; Fábián, Gábor; Baumgartner, Andreas; Schönenberger, Christian; Nygård, Jesper

    2013-12-04

    The determination and control of the electron g-factor in semiconductor quantum dots (QDs) are fundamental prerequisites in modern concepts of spintronics and spin-based quantum computation. We study the dependence of the g-factor on the orientation of an external magnetic field in quantum dots (QDs) formed between two metallic contacts on stacking fault free InAs nanowires. We extract the g-factor from the splitting of Kondo resonances and find that it varies continuously in the range between |g*| = 5 and 15.

  20. g factor of the 2{sub 1}{sup +} state of {sup 172}Hf

    SciTech Connect (OSTI)

    Berant, Z.; Wolf, A.; Oster, E.; Casperson, R. J.; Werner, V.; Heinz, A.; Casten, R. F.; Terry, J. R.; Winkler, R.; Williams, E.; Qian, J.; Schmidt, A.; Smith, M. K.; Ahn, T.; Gurdal, G.; McCutchan, E. A.; Brenner, D. S.; Beausang, C. W.; Regan, P. H.; Ross, T.

    2009-11-15

    The g factor of the 2{sub 1}{sup +} state of {sup 172}Hf was measured using the perturbed angular correlation technique in a static external magnetic field. The result, g(2{sub 1}{sup +})=0.25(5), is discussed in relation to the systematics of the previously reported g factors in the Hf isotopes and compared with the predictions of several models. An interesting outcome of the analysis presented in this paper is the agreement between the calculated g factors within the interacting boson approximation (IBA) and the results of a large-scale shell model calculation. This agreement supports the emphasis in the IBA on the valence space. The undershooting of the empirical g factors near midshell in both models suggests that they underestimate the role of the saturation of collectivity, which is explicitly incorporated into a phenomenological model that agrees better with the data.

  1. g-factor of the 2{sup+}{sub{1} state of {sup179}Hf.

    SciTech Connect (OSTI)

    Berant, Z.; Oster, E.; Wolf, A.; Casperson, R. J.; Werner, V.; McCutchan, E. A.

    2009-01-01

    The g factor of the 2{sub 1}{sup +} state of {sup 172}Hf was measured using the perturbed angular correlation technique in a static external magnetic field. The result, g(2{sub 1}{sup +}) = 0.25(5), is discussed in relation to the systematics of the previously reported g factors in the Hf isotopes and compared with the predictions of several models. An interesting outcome of the analysis presented in this paper is the agreement between the calculated g factors within the interacting boson approximation (IBA) and the results of a large-scale shell model calculation. This agreement supports the emphasis in the IBA on the valence space. The undershooting of the empirical g factors near midshell in both models suggests that they underestimate the role of the saturation of collectivity, which is explicitly incorporated into a phenomenological model that agrees better with the data.

  2. Electromagnetic form factors of the nucleon: New fit and analysis of uncertainties

    SciTech Connect (OSTI)

    Alberico, W. M.; Giunti, C.; Bilenky, S. M.; Graczyk, K. M.

    2009-06-15

    Electromagnetic form factors of proton and neutron, obtained from a new fit of data, are presented. The proton form factors are obtained from a simultaneous fit to the ratio {mu}{sub p}G{sub Ep}/G{sub Mp} determined from polarization transfer measurements and to ep elastic cross section data. Phenomenological two-photon exchange corrections are taken into account. The present fit for protons was performed in the kinematical region Q{sup 2} is an element of (0,6) GeV{sup 2}. For both protons and neutrons we use the latest available data. For all form factors, the uncertainties and correlations of form factor parameters are investigated with the {chi}{sup 2} method.

  3. Self-assembling peptide amphiphiles and related methods for growth factor delivery

    DOE Patents [OSTI]

    Stupp, Samuel I; Donners, Jack J.J.M.; Silva, Gabriel A; Behanna, Heather A; Anthony, Shawn G

    2013-11-12

    Amphiphilic peptide compounds comprising one or more epitope sequences for binding interaction with one or more corresponding growth factors, micellar assemblies of such compounds and related methods of use.

  4. Self-assembling peptide amphiphiles and related methods for growth factor delivery

    DOE Patents [OSTI]

    Stupp, Samuel I. (Chicago, IL); Donners, Jack J. J. M. (Evanston, IL); Silva, Gabriel A. (Chicago, IL); Behanna, Heather A. (Chicago, IL); Anthony, Shawn G. (New Stanton, PA)

    2009-06-09

    Amphiphilic peptide compounds comprising one or more epitope sequences for binding interaction with one or more corresponding growth factors, micellar assemblies of such compounds and related methods of use.

  5. Self-assembling peptide amphiphiles and related methods for growth factor delivery

    DOE Patents [OSTI]

    Stupp, Samuel I. (Chicago, IL); Donners, Jack J. J. M. (Chicago, IL); Silva, Gabriel A. (Chicago, IL); Behanna, Heather A. (Chicago, IL); Anthony, Shawn G. (New Stanton, PA)

    2012-03-20

    Amphiphilic peptide compounds comprising one or more epitope sequences for binding interaction with one or more corresponding growth factors, micellar assemblies of such compounds and related methods of use.

  6. ORNL/CP-97155 Instantaneous Reactive Power and Power Factor of

    Office of Scientific and Technical Information (OSTI)

    97155 Instantaneous Reactive Power and Power Factor of Instantaneous Phasor s ' 4 . L;, Oak Ridge National Laboratory* P f Senior Member &Eb "'ii Lf .. John S. Hsu 4- p d Post ...

  7. On-line method of determining utilization factor in Hg-196 photochemical separation process

    DOE Patents [OSTI]

    Grossman, Mark W. (Belmont, MA); Moskowitz, Philip E. (Peabody, MA)

    1992-01-01

    The present invention is directed to a method for determining the utilization factor [U] in a photochemical mercury enrichment process (.sup.196 Hg) by measuring relative .sup.196 Hg densities using absorption spectroscopy.

  8. Discovery of Novel P1 Groups for Coagulation Factor VIIa Inhibition...

    Office of Scientific and Technical Information (OSTI)

    Discovery of Novel P1 Groups for Coagulation Factor VIIa Inhibition Using Fragment-Based Screening Citation Details In-Document Search Title: Discovery of Novel P1 Groups for ...

  9. Dispersive representation and shape of the K{sub l3} form factors: Robustness

    SciTech Connect (OSTI)

    Bernard, Veronique; Stern, Jan; Passemar, Emilie

    2009-08-01

    An accurate low-energy dispersive parametrization of the scalar K{pi} form factor was constructed some time ago in terms of a single parameter guided by the Callan-Treiman low-energy theorem. A similar twice-subtracted dispersive parametrization for the vector K{pi} form factor will be investigated here. The robustness of the parametrization of these two form factors will be studied in great detail. In particular the cutoff dependence, the isospin breaking effects, and the possible, though not highly probable, presence of zeros in the form factors will be discussed. Interesting constraints in the latter case will be obtained from the soft-kaon analog of the Callan-Treiman theorem and a comparison with the recent {tau}{yields}K{pi}{nu}{sub {tau}} data.

  10. Cavity loss factors of non-relativistic beams for Project X

    SciTech Connect (OSTI)

    Lunin, A.; Yakovlev, V.; Kazakov, S.; /Fermilab

    2011-03-01

    Cavity loss factor calculation is an important part of the total cryolosses estimation for the super conductive (SC) accelerating structures. There are two approaches how to calculate cavity loss factors, the integration of a wake potential over the bunch profile and the addition of loss factors for individual cavity modes. We applied both methods in order to get reliable results for non-relativistic beam. The time domain CST solver was used for a wake potential calculation and the frequency domain HFSS code was used for the cavity eigenmodes spectrum findings. Finally we present the results of cavity loss factors simulations for a non-relativistic part of the ProjectX and analyze it for various beam parameters.

  11. SECTION M EVALUATION FACTORS FOR AWARD TABLE OF CONTENTS M-1 EVALUATION OF PROPOSALS .....................................................................................2

    National Nuclear Security Administration (NNSA)

    TABLE OF CONTENTS M-1 EVALUATION OF PROPOSALS .....................................................................................2 M-2 BASIS FOR CONTRACT AWARD ...................................................................................3 M-3 TECHNICAL AND MANAGEMENT CRITERIA ..........................................................3 M-4 COST EVALUATION CRITERION .................................................................................5 Section M, Evaluation Factors Request for

  12. SECTION M EVALUATION FACTORS FOR AWARD TABLE OF CONTENTS M-1 EVALUATION OF PROPOSALS .....................................................................................2

    National Nuclear Security Administration (NNSA)

    M EVALUATION FACTORS FOR AWARD TABLE OF CONTENTS M-1 EVALUATION OF PROPOSALS .....................................................................................2 M-2 BASIS FOR CONTRACT AWARD ...................................................................................3 M-3 TECHNICAL AND MANAGEMENT CRITERIA ..........................................................3 M-4 COST CRITERION

  13. Final Technical Report: Advanced Measurement and Analysis of PV Derate Factors.

    SciTech Connect (OSTI)

    King, Bruce Hardison; Burton, Patrick D.; Hansen, Clifford; Jones, Christian Birk

    2015-12-01

    The Advanced Measurement and Analysis of PV Derate Factors project focuses on improving the accuracy and reducing the uncertainty of PV performance model predictions by addressing a common element of all PV performance models referred to as “derates”. Widespread use of “rules of thumb”, combined with significant uncertainty regarding appropriate values for these factors contribute to uncertainty in projected energy production.

  14. Identification and Characterization of Soluble Factors Involved in Delayed Effects of Low Dose Radiation. Final report

    SciTech Connect (OSTI)

    Baulch, Janet

    2013-09-11

    This is a 'glue grant' that was part of a DOE Low Dose project entitled 'Identification and Characterization of Soluble Factors Involved in Delayed Effects of Low Dose Radiation'. This collaborative program has involved Drs. David L. Springer from Pacific Northwest National Laboratory (PNNL), John H. Miller from Washington State University, Tri-cities (WSU) and William F. Morgan then from the University of Maryland, Baltimore (UMB). In July 2008, Dr. Morgan moved to PNNL and Dr. Janet E. Baulch became PI for this project at University of Maryland. In November of 2008, a one year extension with no new funds was requested to complete the proteomic analyses. The project stemmed from studies in the Morgan laboratory demonstrating that genomically unstable cells secret a soluble factor or factors into the culture medium, that cause cytogenetic aberrations and apoptosis in normal parental GM10115 cells. The purpose of this project was to identify the death inducing effect (DIE) factor or factors, estimate their relative abundance, identify the cell signaling pathways involved and finally recapitulate DIE in normal cells by exogenous manipulation of putative DIE factors in culture medium. As reported in detail in the previous progress report, analysis of culture medium from the parental cell line, and stable and unstable clones demonstrated inconsistent proteomic profiles as relate to candidate DIE factors. While the proposed proteomic analyses did not provide information that would allow DIE factors to be identified, the analyses provided another important set of observations. Proteomic analysis suggested that proteins associated with the cellular response to oxidative stress and mitochondrial function were elevated in the medium from unstable clones in a manner consistent with mitochondrial dysfunction. These findings correlate with previous studies of these clones that demonstrated functional differences between the mitochondria of stable and unstable clones. These mitochondrial abnormalities in the unstable clones contributes to oxidative stress.

  15. Energy Price Indices and Discount Factors for Life-Cycle Cost Analysis -

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2015 | Department of Energy Price Indices and Discount Factors for Life-Cycle Cost Analysis - 2015 Energy Price Indices and Discount Factors for Life-Cycle Cost Analysis - 2015 Handbook describes the annual supplements to the NIST Handbook 135 and NBS Special Publication 709. PDF icon ashb15.pdf More Documents & Publications Guidance on Life-Cycle Cost Analysis Required by Executive Order 13123 Vehicle Technologies Office Merit Review 2015: Fuel-Neutral Studies of Particulate Matter

  16. High Quality Factor Fano-Resonant All-Dielectric Metamaterials (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect High Quality Factor Fano-Resonant All-Dielectric Metamaterials Citation Details In-Document Search Title: High Quality Factor Fano-Resonant All-Dielectric Metamaterials Authors: Yang, Yuanmu [1] ; Kravchenko, Ivan I [2] ; Briggs, Dayrl P [2] ; Valentine, Jason [1] + Show Author Affiliations Vanderbilt University, Nashville ORNL Publication Date: 2014-01-01 OSTI Identifier: 1185509 DOE Contract Number: DE-AC05-00OR22725 Resource Type: Journal Article Resource

  17. Method for determining formation quality factor from well log data and its

    Office of Scientific and Technical Information (OSTI)

    application to seismic reservoir characterization (Patent) | SciTech Connect Patent: Method for determining formation quality factor from well log data and its application to seismic reservoir characterization Citation Details In-Document Search Title: Method for determining formation quality factor from well log data and its application to seismic reservoir characterization A method for seismic characterization of subsurface Earth formations includes determining at least one of

  18. Method for determining formation quality factor from well log data and its

    Office of Scientific and Technical Information (OSTI)

    application to seismic reservoir characterization (Patent) | SciTech Connect Patent: Method for determining formation quality factor from well log data and its application to seismic reservoir characterization Citation Details In-Document Search Title: Method for determining formation quality factor from well log data and its application to seismic reservoir characterization × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's

  19. Human Reliability Analysis for Design: Using Reliability Methods for Human Factors Issues

    SciTech Connect (OSTI)

    Ronald Laurids Boring

    2010-11-01

    This paper reviews the application of human reliability analysis methods to human factors design issues. An application framework is sketched in which aspects of modeling typically found in human reliability analysis are used in a complementary fashion to the existing human factors phases of design and testing. The paper provides best achievable practices for design, testing, and modeling. Such best achievable practices may be used to evaluate and human system interface in the context of design safety certifications.

  20. Discovery of Novel P1 Groups for Coagulation Factor VIIa Inhibition Using

    Office of Scientific and Technical Information (OSTI)

    Fragment-Based Screening (Journal Article) | SciTech Connect Discovery of Novel P1 Groups for Coagulation Factor VIIa Inhibition Using Fragment-Based Screening Citation Details In-Document Search Title: Discovery of Novel P1 Groups for Coagulation Factor VIIa Inhibition Using Fragment-Based Screening Authors: Cheney, Daniel L. ; Bozarth, Jeffrey M. ; Metzler, William J. ; Morin, Paul E. ; Mueller, Luciano ; Newitt, John A. ; Nirschl, Alexandra H. ; Rendina, Alan R. ; Tamura, James K. ; Wei,

  1. Crystal structure of elongation factor 4 bound to a clockwise ratcheted

    Office of Scientific and Technical Information (OSTI)

    ribosome (Journal Article) | SciTech Connect SciTech Connect Search Results Journal Article: Crystal structure of elongation factor 4 bound to a clockwise ratcheted ribosome Citation Details In-Document Search Title: Crystal structure of elongation factor 4 bound to a clockwise ratcheted ribosome Authors: Gagnon, Matthieu G. ; Lin, Jinzhong ; Bulkley, David ; Steitz, Thomas A. [1] ; HHMI) [2] + Show Author Affiliations (Yale) ( Publication Date: 2014-08-14 OSTI Identifier: 1150141 Resource

  2. New results from BLAST on the nucleon electromagnetic form factors (Journal

    Office of Scientific and Technical Information (OSTI)

    Article) | SciTech Connect New results from BLAST on the nucleon electromagnetic form factors Citation Details In-Document Search Title: New results from BLAST on the nucleon electromagnetic form factors Recently, a new experiment was carried out in the South Hall Ring at the MIT-Bates Accelerator Laboratory. This experiment utilized a polarized electron beam, a pure hydrogen (deuterium) internal polarized gas target, and the symmetric Bates Large Acceptance Spectrometer Toroid (BLAST)

  3. Central safety factor and β N control on NSTX-U via beam power and plasma

    Office of Scientific and Technical Information (OSTI)

    boundary shape modification, using TRANSP for closed loop simulations (Journal Article) | SciTech Connect Central safety factor and β N control on NSTX-U via beam power and plasma boundary shape modification, using TRANSP for closed loop simulations Citation Details In-Document Search This content will become publicly available on April 23, 2016 Title: Central safety factor and β N control on NSTX-U via beam power and plasma boundary shape modification, using TRANSP for closed loop

  4. Acceleration Factors for Damp-Heat and HAST with High Voltage Stress |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Acceleration Factors for Damp-Heat and HAST with High Voltage Stress Acceleration Factors for Damp-Heat and HAST with High Voltage Stress Presented at the PV Module Reliability Workshop, February 26 - 27 2013, Golden, Colorado PDF icon pvmrw13_ps5_d2_rowell.pdf More Documents & Publications High PID Resistant Cross-Linked Encapsulnt Based on Polyolefin SOLAR ASCE Comparing Accelerated Testing and Outdoor Exposure

  5. Simulation of a Wireless Power Transfer System for Electric Vehicles with Power Factor Correction

    SciTech Connect (OSTI)

    Pickelsimer, Michael C; Tolbert, Leon M; Ozpineci, Burak; Miller, John M

    2012-01-01

    Wireless power transfer has been a popular topic of recent research. Most research has been done to address the limitations of coil-to-coil efficiency. However, little has been done to address the problem associated with the low input power factor with which the systems operate. This paper details the steps taken to analyze a wireless power transfer system from the view of the power grid under a variety of loading conditions with and without power factor correction.

  6. Tuning g factors of core-shell nanoparticles by controlled positioning of

    Office of Scientific and Technical Information (OSTI)

    magnetic impurities (Journal Article) | DOE PAGES Tuning g factors of core-shell nanoparticles by controlled positioning of magnetic impurities This content will become publicly available on February 22, 2017 « Prev Next » Title: Tuning g factors of core-shell nanoparticles by controlled positioning of magnetic impurities Authors: Sanders, G. D. ; Musfeldt, J. L. ; Stanton, C. J. Publication Date: 2016-02-23 OSTI Identifier: 1238826 Grant/Contract Number: FG02-01ER45885 Type: Publisher's

  7. Spatiotemporal Distribution of NOx Storage: a Factor Controlling NH3 and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    N2O Selectivities over a Commercial LNT Catalyst | Department of Energy Spatiotemporal Distribution of NOx Storage: a Factor Controlling NH3 and N2O Selectivities over a Commercial LNT Catalyst Spatiotemporal Distribution of NOx Storage: a Factor Controlling NH3 and N2O Selectivities over a Commercial LNT Catalyst Evaluation of commercial Ba-based LNT (CLEERS benchmark catalyst; containing oxygen storage capacity) in a bench flow reactor under fast-cycling conditions, varying reductant type,

  8. FE-Funded Study Released on Key Factors Affecting China Shale Gas

    Office of Environmental Management (EM)

    Development | Department of Energy FE-Funded Study Released on Key Factors Affecting China Shale Gas Development FE-Funded Study Released on Key Factors Affecting China Shale Gas Development September 12, 2014 - 7:14am Addthis As many people know, over the past decade the United States has experienced a shale gas revolution that has beneficially transformed its energy landscape. In witnessing this transformation, other nations with significant shale resources are understandably interested in

  9. GHG emission factors developed for the recycling and composting of municipal waste in South African municipalities

    SciTech Connect (OSTI)

    Friedrich, Elena Trois, Cristina

    2013-11-15

    Highlights: • GHG emission factors for local recycling of municipal waste are presented. • GHG emission factors for two composting technologies for garden waste are included. • Local GHG emission factors were compared to international ones and discussed. • Uncertainties and limitations are presented and areas for new research highlighted. - Abstract: GHG (greenhouse gas) emission factors for waste management are increasingly used, but such factors are very scarce for developing countries. This paper shows how such factors have been developed for the recycling of glass, metals (Al and Fe), plastics and paper from municipal solid waste, as well as for the composting of garden refuse in South Africa. The emission factors developed for the different recyclables in the country show savings varying from ?290 kg CO{sub 2} e (glass) to ?19 111 kg CO{sub 2} e (metals – Al) per tonne of recyclable. They also show that there is variability, with energy intensive materials like metals having higher GHG savings in South Africa as compared to other countries. This underlines the interrelation of the waste management system of a country/region with other systems, in particular with energy generation, which in South Africa, is heavily reliant on coal. This study also shows that composting of garden waste is a net GHG emitter, releasing 172 and 186 kg CO{sub 2} e per tonne of wet garden waste for aerated dome composting and turned windrow composting, respectively. The paper concludes that these emission factors are facilitating GHG emissions modelling for waste management in South Africa and enabling local municipalities to identify best practice in this regard.

  10. DOE Order 458.1 Property Clearance Requirements and Factors Considered to

    Office of Environmental Management (EM)

    Update Its Clearance Limits | Department of Energy 58.1 Property Clearance Requirements and Factors Considered to Update Its Clearance Limits DOE Order 458.1 Property Clearance Requirements and Factors Considered to Update Its Clearance Limits Carlos Corredor, U.S. Department of Energy ;Gustavo Vasquez*, U.S. Department of Energy; Derek Favret, U.S. Department of Energy Abstract: This presentation will provide an explanation of the property clearance requirements contained in DOE O 458.1,

  11. Herbert Richardson: Before The U.S. House of Representatives...

    Broader source: Energy.gov (indexed) [DOE]

    Our work has been extensive and across the security spectrum, including physical security, personnel security, cyber security, and the protection of Department assets, such as ...

  12. Polytechnic Institute of New York University Researchers Represented...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    E-print Network ResearcherResearch Institution Web page Aronov, Boris - Department of Computer Science and Engineering, Polytechnic Institute of New York University http:...

  13. A comparison of methods for representing sparsely sampled random quantities.

    SciTech Connect (OSTI)

    Romero, Vicente Jose; Swiler, Laura Painton; Urbina, Angel; Mullins, Joshua

    2013-09-01

    This report discusses the treatment of uncertainties stemming from relatively few samples of random quantities. The importance of this topic extends beyond experimental data uncertainty to situations involving uncertainty in model calibration, validation, and prediction. With very sparse data samples it is not practical to have a goal of accurately estimating the underlying probability density function (PDF). Rather, a pragmatic goal is that the uncertainty representation should be conservative so as to bound a specified percentile range of the actual PDF, say the range between 0.025 and .975 percentiles, with reasonable reliability. A second, opposing objective is that the representation not be overly conservative; that it minimally over-estimate the desired percentile range of the actual PDF. The presence of the two opposing objectives makes the sparse-data uncertainty representation problem interesting and difficult. In this report, five uncertainty representation techniques are characterized for their performance on twenty-one test problems (over thousands of trials for each problem) according to these two opposing objectives and other performance measures. Two of the methods, statistical Tolerance Intervals and a kernel density approach specifically developed for handling sparse data, exhibit significantly better overall performance than the others.

  14. Secretary Chu: China's Clean Energy Successes Represent a New...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    November 29, 2010 - 12:00am Addthis Washington, D.C. - In a speech at the National Press ... Missed Secretary Chu's "Sputnik Moment" Speech? Readout of Secretary Chu Meetings on ...

  15. FAQS Gap Analysis Qualification Card – Facility Representative

    Broader source: Energy.gov [DOE]

    Functional Area Qualification Standard Gap Analysis Qualification Cards outline the differences between the last and latest version of the FAQ Standard.

  16. Evaluation of Representative Smart Grid Investment Project Technologies: Demand Response

    SciTech Connect (OSTI)

    Fuller, Jason C.; Prakash Kumar, Nirupama; Bonebrake, Christopher A.

    2012-02-14

    This document is one of a series of reports estimating the benefits of deploying technologies similar to those implemented on the Smart Grid Investment Grant (SGIG) projects. Four technical reports cover the various types of technologies deployed in the SGIG projects, distribution automation, demand response, energy storage, and renewables integration. A fifth report in the series examines the benefits of deploying these technologies on a national level. This technical report examines the impacts of a limited number of demand response technologies and implementations deployed in the SGIG projects.

  17. Secretary Chu to Join Representatives Lofgren and Honda at the...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    questions in photon science, astrophysics, particle physics and accelerator research. ... The World's First Free-Electron X-ray Laser Secretary Chu Dedicates World's Most ...

  18. The technical and financial evaluations represent the total evaluation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the process of selecting projects seeking financial assistance under Round 2 of the Clean Coal Power Initiative (CCPI), which DOE issued as a Funding Opportunity Announcement (FOA) ...

  19. DOE Honors WIPP Representative for Cutting Travel Costs, Greenhouse...

    Office of Environmental Management (EM)

    document reviews with regulators instead of meeting in person and reduced rental car usage by standardizing travel arrangements so that only one rental car is necessary per...

  20. Percent of Commercial Natural Gas Deliveries in California Represented by

    Gasoline and Diesel Fuel Update (EIA)

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 94.6 95.1 93.0 88.3 94.8 92.8 89.4 87.8 91.0 88.5 90.1 92.2 1990 95.8 81.1 94.4 90.4 90.2 85.6 78.0 82.6 79.1 82.3 85.6 88.3 1991 90.5 88.4 90.2 71.0 82.2 71.0 68.0 85.8 68.0 64.7 69.8 80.3 1992 86.6 65.6 75.7 79.0 63.5 74.5 60.9 64.6 79.7 79.0 76.7 81.4 1993 79.9 82.3 77.6 80.7 76.8 71.4 76.4 70.3 70.6 73.8 75.7 78.8 1994 51.3 47.2 50.6 40.5 47.4 32.2 36.4 46.5 46.0 52.2 57.8 68.2 1995 61.3 58.6 64.7 56.8 50.3

  1. Percent of Commercial Natural Gas Deliveries in Connecticut Represented by

    Gasoline and Diesel Fuel Update (EIA)

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 100.0 100.0 98.4 90.0 81.6 76.5 74.5 80.4 74.8 85.5 90.8 99.5 1990 100.0 100.0 98.7 95.9 92.3 89.9 87.5 86.9 87.2 91.3 98.3 99.1 1991 99.4 99.4 97.5 92.5 85.9 79.2 76.2 77.1 77.9 85.9 93.0 96.6 1992 97.7 97.2 95.6 94.4 93.6 87.2 95.8 98.8 98.7 97.8 98.2 98.4 1993 97.2 97.7 97.2 98.1 99.4 99.3 88.3 98.4 99.6 100.0 100.0 100.0 1994 89.2 90.7 88.4 88.8 74.2 67.8 62.4 61.1 57.4 68.8 77.9 83.4 1995 86.7 88.1 85.7 81.6

  2. Percent of Commercial Natural Gas Deliveries in Louisiana Represented by

    Gasoline and Diesel Fuel Update (EIA)

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 1990 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 1991 100.0 100.0 100.0 100.0 100.0 98.5 98.6 98.4 98.5 98.4 97.4 97.6 1992 82.3 87.7 88.7 90.6 90.5 90.1 90.6 90.2 91.1 90.6 81.4 86.4 1993 97.4 97.9 98.1 98.6 98.9 98.9 98.8 98.8 98.8 98.2 97.1 97.5 1994 97.7 98.1 98.1 98.0 98.0 97.9 98.4 97.6 98.1 97.9 97.9 97.5 1995 97.8 98.2

  3. Percent of Commercial Natural Gas Deliveries in Massachusetts Represented

    Gasoline and Diesel Fuel Update (EIA)

    by the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 1990 100.0 100.0 100.0 100.0 100.0 100.0 100.0 99.8 99.8 99.8 99.7 99.7 1991 99.8 99.8 99.9 99.9 99.9 99.8 99.7 99.6 99.6 99.8 99.9 99.9 1992 99.9 99.9 99.8 99.8 99.7 99.8 99.7 99.6 99.6 99.6 99.7 99.8 1993 98.9 98.7 98.5 97.7 96.5 97.7 96.8 89.2 97.5 96.7 96.9 97.8 1994 75.2 78.4 72.5 69.8 69.8 61.2 67.0 86.0 79.7 90.6 81.2 87.1 1995 87.9 89.4 92.0

  4. Percent of Commercial Natural Gas Deliveries in Minnesota Represented by

    Gasoline and Diesel Fuel Update (EIA)

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 97.3 97.4 97.0 95.8 95.0 92.4 89.4 89.9 92.7 91.9 94.9 97.0 1990 97.7 96.4 95.9 94.9 94.9 91.4 86.2 89.9 90.1 92.8 97.9 98.7 1991 96.8 96.3 97.6 95.9 89.2 80.9 79.3 81.5 90.5 97.8 97.0 99.0 1992 99.6 95.3 96.0 95.5 92.2 88.3 93.1 89.8 93.0 99.4 96.5 97.6 1993 98.7 96.9 96.3 99.2 99.2 93.4 88.2 87.1 96.2 95.3 96.5 99.1 1994 97.2 97.6 97.3 96.8 98.5 91.4 97.0 91.8 89.8 91.9 95.6 95.2 1995 93.3 93.6 95.0 96.2 95.5

  5. Percent of Commercial Natural Gas Deliveries in Mississippi Represented by

    Gasoline and Diesel Fuel Update (EIA)

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 1990 97.6 96.0 95.7 95.6 94.5 94.3 93.7 93.5 93.9 94.4 95.2 95.8 1991 96.6 97.0 96.3 95.9 94.5 94.9 94.3 94.6 95.1 94.9 95.5 96.4 1992 96.9 97.3 96.4 96.6 95.2 95.4 95.5 94.8 95.6 95.6 95.9 97.4 1993 97.3 97.3 97.2 97.1 96.1 96.0 96.0 95.7 95.5 95.4 96.1 96.5 1994 97.2 97.6 97.1 96.9 96.1 96.9 97.1 95.1 94.9 94.3 96.2 96.6 1995 96.4 97.4 98.2

  6. Percent of Commercial Natural Gas Deliveries in New Hampshire Represented

    Gasoline and Diesel Fuel Update (EIA)

    by the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 1990 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 1991 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 1992 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 1993 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 100.0 1994 100.0 100.0 100.0 100.0 100.0

  7. Percent of Commercial Natural Gas Deliveries in Pennsylvania Represented by

    Gasoline and Diesel Fuel Update (EIA)

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 89.4 88.9 88.7 87.4 81.7 76.8 79.6 77.2 76.4 80.3 82.9 85.3 1990 85.9 83.6 80.9 80.0 74.0 70.2 68.5 68.3 67.2 69.6 74.9 79.2 1991 82.2 79.4 78.8 77.7 72.1 72.9 70.6 71.6 72.2 72.9 76.4 76.7 1992 77.1 79.6 76.6 75.1 71.8 73.1 68.1 67.2 69.4 74.0 74.1 79.4 1993 80.5 79.7 79.5 78.2 72.1 72.9 72.9 69.7 70.3 76.5 75.9 77.0 1994 79.0 80.2 77.5 73.9 71.6 70.8 67.1 71.4 67.9 62.7 68.7 72.1 1995 75.1 74.4 74.9 71.4 68.7

  8. Percent of Commercial Natural Gas Deliveries in South Carolina Represented

    Gasoline and Diesel Fuel Update (EIA)

    by the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 98.5 98.5 98.6 98.3 98.1 98.2 98.1 97.7 97.7 97.8 98.0 97.3 1990 98.6 98.4 98.3 98.1 92.2 97.6 97.6 97.5 97.9 97.3 98.0 98.6 1991 98.7 98.9 98.7 96.9 97.4 97.5 97.3 97.7 97.7 97.4 98.9 98.9 1992 99.1 99.1 98.9 98.6 98.5 95.8 95.5 95.8 97.0 99.7 100.0 100.0 1993 100.0 100.0 100.0 100.0 100.0 100.0 95.1 94.6 100.0 95.3 100.0 100.0 1994 100.0 100.0 100.0 99.7 97.8 98.3 97.0 95.7 95.2 95.6 96.2 99.9 1995 97.8 97.5

  9. Percent of Commercial Natural Gas Deliveries in Tennessee Represented by

    Gasoline and Diesel Fuel Update (EIA)

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 99.1 98.9 98.9 97.5 96.8 95.9 96.7 95.8 96.9 97.1 97.4 99.1 1990 98.9 98.5 98.7 97.9 95.4 95.4 95.1 95.9 95.1 95.5 96.5 97.5 1991 97.9 94.6 93.6 96.0 94.8 94.3 93.8 93.8 94.0 95.3 97.1 97.8 1992 96.6 97.1 96.8 97.2 93.7 95.8 97.3 90.4 91.6 97.3 97.5 97.4 1993 96.6 96.9 96.6 96.5 97.7 91.3 91.6 91.1 91.4 92.3 94.7 98.9 1994 96.7 98.5 97.9 93.0 90.0 89.4 87.2 87.1 89.3 88.4 91.7 94.4 1995 95.5 95.8 93.4 90.8 89.6

  10. Percent of Commercial Natural Gas Deliveries in Washington Represented by

    Gasoline and Diesel Fuel Update (EIA)

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 95.5 94.8 96.9 93.2 93.0 89.7 87.0 92.6 87.3 93.0 93.6 96.5 1990 96.2 95.9 93.2 92.1 90.9 88.9 88.3 88.4 90.1 91.7 95.7 96.5 1991 97.8 94.9 94.3 93.2 91.2 90.5 88.3 87.2 85.6 85.2 88.7 92.1 1992 92.1 89.0 88.7 85.5 83.5 80.7 78.5 80.3 81.6 83.4 86.8 92.3 1993 93.8 93.2 93.9 93.6 90.8 89.8 90.5 90.4 90.6 94.8 97.4 98.0 1994 97.6 97.6 97.6 97.4 92.1 92.1 92.4 91.7 94.4 93.8 94.1 94.7 1995 94.3 94.0 94.2 92.6 91.8

  11. Percent of Commercial Natural Gas Deliveries in West Virginia Represented

    Gasoline and Diesel Fuel Update (EIA)

    by the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 68.6 69.0 65.3 63.9 55.0 45.3 39.8 39.5 40.5 49.5 58.6 71.5 1990 72.4 67.8 64.6 60.4 53.8 41.6 34.0 37.7 34.7 38.3 56.1 61.2 1991 64.6 65.8 65.4 54.5 42.1 34.1 31.0 33.9 36.5 45.2 55.6 58.0 1992 65.0 65.9 59.9 63.0 54.5 39.3 35.8 33.6 33.4 48.1 56.8 58.9 1993 60.7 61.3 61.7 60.2 47.5 33.6 30.3 30.6 33.0 46.8 54.9 60.1 1994 67.4 65.2 61.9 58.3 47.8 39.6 29.5 34.3 34.2 41.3 47.5 55.7 1995 55.5 59.5 56.1 50.6 42.2

  12. Percent of Commercial Natural Gas Deliveries in Wisconsin Represented by

    Gasoline and Diesel Fuel Update (EIA)

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1989 94.1 94.2 94.5 94.0 92.6 87.7 86.1 84.2 84.2 84.3 91.1 95.0 1990 91.6 91.5 91.9 91.9 90.3 86.5 83.1 82.4 82.6 87.5 90.1 93.3 1991 93.8 92.3 92.9 91.2 88.8 83.8 80.7 84.7 83.6 86.7 91.5 92.1 1992 92.7 92.1 91.6 90.0 85.8 82.3 83.3 84.1 85.2 90.7 93.4 95.1 1993 95.2 96.0 95.3 93.5 92.1 90.8 89.2 88.5 90.0 92.6 95.2 96.0 1994 97.1 97.6 97.4 96.6 91.8 89.9 83.5 87.1 87.8 90.8 94.4 84.4 1995 93.5 94.0 93.2 92.4 90.0

  13. U.S. Representative Cleaver congratulates KCP employees for safety...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    praised employees for keeping safety and security a primary focus and reiterated the importance of the plant's national security mission. The massive relocation of the...

  14. U.S. Representative Frank Lucas and Oklahoma State Senator

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    clouds absorb 40% more incoming solar radiation than earlier work had predicted. This finding greatly alters the way a computer climate model distributes energy throughout the...

  15. Howard University Researchers Represented in the E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ww.biology.howard.edu FacultyFacultyBiosEckberg.htm Hindman, Neil - Department of Mathematics, Howard University http:mysite.verizon.netnhindman Sitaraman, Sankar -...

  16. W&M Student Elected to Represent American Physical Society's...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in the APS and the scientific community at large and to enhance the ability of APS to meet the needs of graduate students. It also offers support services and encourages...

  17. Fluid Flow Model Development for Representative Geologic Media

    Broader source: Energy.gov [DOE]

    Clay and granitic geologic rock units are potential host media for future repositories for used nuclear fuel and high level waste. This report addresses the representation of flow in these two media within numerical process (discrete fracture network) models.

  18. Percent of Industrial Natural Gas Deliveries in California Represented by

    U.S. Energy Information Administration (EIA) Indexed Site

    the Price (Percent) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1990's 9.0 10.4 12.9 2000's 8.7 9.1 7.7 4.9 5.2 5.5 5.7 5.3 5.1 4.7 2010's 4.6 4.5 4.2 4.0 3.7 3.8

  19. Percent of Industrial Natural Gas Deliveries in California Represented by

    U.S. Energy Information Administration (EIA) Indexed Site

    the Price (Percent) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 2001 14.3 12.9 13.0 10.4 9.0 7.7 6.6 6.7 6.4 8.0 8.2 8.0 2002 8.0 9.4 8.8 7.4 9.5 7.0 6.6 6.9 6.7 7.7 7.2 8.1 2003 3.3 7.1 4.9 5.8 5.1 4.6 4.0 4.8 4.3 4.1 5.3 6.2 2004 5.2 8.3 5.8 5.2 5.3 3.8 4.6 4.4 4.3 5.0 5.3 5.9 2005 5.6 6.6 4.8 5.3 5.2 5.1 4.5 4.8 5.2 5.8 5.9 6.7 2006 6.2 7.2 5.7 5.9 6.0 5.4 4.6 4.7 4.9 5.3 6.1 6.2 2007 6.0 7.2 6.5 5.3 5.6 4.9 4.5 4.3 4.3 5.1 4.8 5.3 2008 5.7 6.6 5.9 5.6 5.6 4.5 4.4 4.3 4.4 4.7 4.7

  20. Percent of Industrial Natural Gas Deliveries in Connecticut Represented by

    U.S. Energy Information Administration (EIA) Indexed Site

    the Price (Percent) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1990's 66.4 55.8 55.8 2000's 47.3 54.0 48.9 45.3 44.0 46.4 48.5 50.0 47.3 37.5 2010's 31.1 31.0 32.3 33.4 39.4 47.2