National Library of Energy BETA

Sample records for dual enthalpy economizer

  1. Dual-purpose desalting, RO versus MSF an economic comparison

    SciTech Connect (OSTI)

    Brandt, D.C.; Battey, R.F.

    1983-01-01

    Capital and annual operating costs are estimated for producing water using three combinations of seawater reverse osmosis and gas turbines. The costs and operating parameters were developed for Middle East conditions assuming a Red Sea water source. The plants were designed to produce 37,850 m/sup 3//d (10 mgd) of potable water and to export 50,000 kW of power. The reverse osmosis plant utilizes energy recovery and was designed with full pretreatment for a surface water supply. Electricity is provided by either gas turbines, steam turbines, or combined cycle plants. Power and water costs developed for these systems were compared to costs for conventional, dual-purpose MSF/steam turbine plants for the same water and power production. These evaluations considered two levels of fuel costs. The results of this study show the significant effect of fuel costs on process selection and on water and power costs. Capital and operating costs were 20 to 28 percent less and 23 to 33 percent less, respectively, for the RO/gas turbine and RO/combined cycle plants as compared to conventional, dual-purpose MSF steam turbine plants. In addition to economics, the merits of the systems are discussed relative to delivery, ease and flexibility of operation, turndown capability, and so forth.

  2. An advanced economizer controller for dual-duct air-handling systems -- with a case application

    SciTech Connect (OSTI)

    Liu, M.; Claridge, D.E.; Park, B.Y.

    1997-12-31

    A heating penalty is expected when economizers are applied to dual-duct air-handling systems. The heating penalty can be even higher than the cooling savings when the hot airflow is higher than the cold airflow. To avoid the excessive heating penalty, advanced economizers are developed in this paper. The application of the advanced economizer has resulted in savings of $7,000/yr in one 95,000-ft{sup 2} (8,800-m{sup 2}) school building since 1993. The impacts of cold and hot deck settings on the energy consumption are also discussed.

  3. Enthalpy Diffusion in Multicomponent Flows

    SciTech Connect (OSTI)

    Cook, A W

    2008-11-12

    The enthalpy diffusion flux in the multicomponent energy equation is a well known yet frequently neglected term. It accounts for energy changes, associated with compositional changes, resulting from species diffusion. Enthalpy diffusion is important in flows where significant mixing occurs between species of dissimilar molecular weight. The term plays a critical role in preventing local violations of the entropy condition. In simulations of nonpremixed combustion, omission of the enthalpy flux can lead to anomalous temperature gradients, which may cause mixing regions to exceed ignition conditions. The term can also play a role in generating acoustic noise in turbulent mixing layers. Euler solvers that rely on numerical diffusion to mix fluids cannot accurately predict the temperature in mixed regions. On the other hand, Navier-Stokes solvers that incorporate enthalpy diffusion can provide much more accurate results.

  4. Dual fuel Russian urban transit buses: Economical reduced emissions. Export trade information

    SciTech Connect (OSTI)

    1998-01-01

    This study, conducted by Caterpillar, was funded by the US Trade and Development Agency. The scope of this project was to examine the financial and environmental aspects of introducing new alternative fuel engines to the buses of Russia`s public transportation system. The report consists of the following: (1) executive summary; (2) background/overview; (3) 3306 design, development, test; (4) electronic governed engines; (5) Moscow bus testing; (6) conclusions; (7) appendices. The appendices include: (1) Caterpillar emissions lab report; (2) dyno tests -- dual fuel data sheets; (3) 3360 horizontal engine lub tilt test; (4) 1000 hour endurance test -- engine operator sheets; (5) 1000 hour endurance test -- 250 hour check; (6) Caterpillar dual fuel electronic engines; (7) product description -- dual fuel electronic governed engines; (8) California Environmental Protection Agency -- certification of caterpillar electronic governed engines; (9) annual payback data.

  5. Enthalpy of formation of gallium nitride

    SciTech Connect (OSTI)

    Ranade, M.R.; Tessier, F.; Navrotsky, A.; Leppert, V.J.; Risbud, S.H.; DiSalvo, F.J.; Balkas, C.M.

    2000-05-04

    A major discrepancy in the literature concerning the enthalpy of formation of GaN has been resolved using oxidative oxide melt solution calorimetry. Four samples of differing nitrogen contents were measured by dropping them into molten 3Na{sub 2}O{center_dot}4MoO{sub 3} in a calorimeter at 975 K with oxygen gas bubbling through the solvent. The samples were characterized by X-ray diffraction, chemical analysis, transmission electron microscopy, particle size analysis, and BET measurements. The enthalpy of drop solution (kJ/g) varied approximately linearly with nitrogen content. Extrapolated to stoichiometric GaN, the data yield a value of {minus}156.8 {+-} 16.0 kJ/mol for the standard enthalpy of formation from the elements at 298 K. The relatively large error reflects the deviation of individual points from the straight line rather than uncertainties in each set of data for a given sample. This new directly measured enthalpy of formation is in excellent agreement with that obtained from the temperature dependence of the equilibrium pressure of nitrogen over GaN, {minus}157.7 kJ/mol, measured by Madar et al. and Karpinski and Porowski. This value of {minus}156.8 kJ/mol should replace the commonly tabulated value of {minus}110 kJ/mol determined by Hahn and Juza using combustion calorimetry on an uncharacterized sample over 50 years ago.

  6. Current Status of the high enthalpy conventional geothermal fields...

    Open Energy Info (EERE)

    Current Status of the high enthalpy conventional geothermal fields in Europe and the potential perspectives for their exploitation in terms of EGS Jump to: navigation, search...

  7. DNA Nanostructures as Models for Evaluating the Role of Enthalpy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of the roles of enthalpy and entropy in the affinity of polyvalent DNA nanostructure interactions, which exhibit an intriguing compensating effect. Date of online publication: ...

  8. Dual Career Services

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Options Dual Career Services Dual Career Services Los Alamos Lab recruits the best minds on the planet and offers job search information and assistance to our dual career...

  9. Insights on activation enthalpy for non-Schmid slip in body-centered cubic metals

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Hale, Lucas M.; Lim, Hojun; Zimmerman, Jonathan A.; Battaile, Corbett C.; Weinberger, Christopher R.

    2014-12-18

    We use insights gained from atomistic simulation to develop an activation enthalpy model for dislocation slip in body-centered cubic iron. Furthermore, using a classical potential that predicts dislocation core stabilities consistent with ab initio predictions, we quantify the non-Schmid stress-dependent effects of slip. The kink-pair activation enthalpy is evaluated and a model is identified as a function of the general stress state. Thus, our model enlarges the applicability of the classic Kocks activation enthalpy model to materials with non-Schmid behavior.

  10. Geological parameters used to determine the low enthalpy geothermal potential of sedimentary formations in France

    SciTech Connect (OSTI)

    Maget, Ph.; Housse, B.A.

    1985-01-01

    The determination of low enthalpy geothermal potential in sedimentary formations and its exploitation require the solution of two different problems, depending on whether the formations under consideration are calcareous or detrital.

  11. Enthalpies of formation of rare earth orthovanadates, REVO{sub 4}

    SciTech Connect (OSTI)

    Dorogova, M.; Navrotsky, A. Boatner, L.A.

    2007-03-15

    Rare earth orthovanadates, REVO{sub 4}, having the zircon structure, form a series of materials interesting for magnetic, optical, sensor, and electronic applications. Enthalpies of formation of REVO{sub 4} compounds (RE=Sc, Y, Ce-Nd, Sm-Tm, Lu) were determined by oxide melt solution calorimetry in lead borate (2PbO.2B{sub 2}O{sub 3}) solvent at 1075 K. The enthalpies of formation from oxide components become more negative with increasing RE ionic radius. This trend is similar to that obtained for the rare earth phosphates. - Graphical abstract: Comparison of enthalpies of formation from oxides at 298 K for REVO{sub 4} [this work] and REPO{sub 4} compounds [S.V. Ushakov, K.B. Helean, A. Navrotsky, L.A. Boatner, J. Mater. Res. 16(9) (2001) 2623] vs. RE{sup 3+} ionic radius. Filled symbols indicate scheelite structure, open symbols zircon structure.

  12. Preliminary Results from Electric Arc Furnace Off-Gas Enthalpy Modeling

    SciTech Connect (OSTI)

    Nimbalkar, Sachin U; Thekdi, Arvind; Keiser, James R; Storey, John Morse

    2015-01-01

    This article describes electric arc furnace (EAF) off-gas enthalpy models developed at Oak Ridge National Laboratory (ORNL) to calculate overall heat availability (sensible and chemical enthalpy) and recoverable heat values (steam or power generation potential) for existing EAF operations and to test ORNL s new EAF waste heat recovery (WHR) concepts. ORNL s new EAF WHR concepts are: Regenerative Drop-out Box System and Fluidized Bed System. The two EAF off-gas enthalpy models described in this paper are: 1.Overall Waste Heat Recovery Model that calculates total heat availability in off-gases of existing EAF operations 2.Regenerative Drop-out Box System Model in which hot EAF off-gases alternately pass through one of two refractory heat sinks that store heat and then transfer it to another gaseous medium These models calculate the sensible and chemical enthalpy of EAF off-gases based on the off-gas chemical composition, temperature, and mass flow rate during tap to tap time, and variations in those parameters in terms of actual values over time. The models provide heat transfer analysis for the aforementioned concepts to confirm the overall system and major component sizing (preliminary) to assess the practicality of the systems. Real-time EAF off-gas composition (e.g., CO, CO2, H2, and H2O), volume flow, and temperature data from one EAF operation was used to test the validity and accuracy of the modeling work. The EAF off-gas data was used to calculate the sensible and chemical enthalpy of the EAF off-gases to generate steam and power. The article provides detailed results from the modeling work that are important to the success of ORNL s EAF WHR project. The EAF WHR project aims to develop and test new concepts and materials that allow cost-effective recovery of sensible and chemical heat from high-temperature gases discharged from EAFs.

  13. HVAC Equipment Rebate Program

    Broader source: Energy.gov [DOE]

    NOTE: As of January 1, 2016, rebates for unitary air conditioning and split systems and integrated dual enthalpy economizer controls are no longer available.

  14. Intergrating Magnetotellurics, Soil Gas Geochemistry and Structural Analysis to Identify Hidden, High Enthalpy, Extensional Geothermal Systems

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Integrating Magnetotellurics, Soil Gas Geochemistry and Structural Analysis to Identify Hidden, High-Enthalpy, Extensional Geothermal Systems Principal Investigator: Philip E. Wannamaker University of Utah Energy & Geoscience Institute 423 Wakara Way, Ste 300 Salt Lake City, UT 84108 pewanna@egi.utah.edu April 24, 2013 This presentation does not contain any proprietary confidential, or otherwise restricted information. Track1: Geophysics McGinness Hills, NV October, 2011 2 | US DOE

  15. Effects of partitioned enthalpy of mixing on glass-forming ability

    SciTech Connect (OSTI)

    Song, Wen-Xiong; Zhao, Shi-Jin

    2015-04-14

    We explore the inherent reason at atomic level for the glass-forming ability of alloys by molecular simulation, in which the effect of partitioned enthalpy of mixing is studied. Based on Morse potential, we divide the enthalpy of mixing into three parts: the chemical part (Δ E{sub nn}), strain part (Δ E{sub strain}), and non-bond part (Δ E{sub nnn}). We find that a large negative Δ E{sub nn} value represents strong AB chemical bonding in AB alloy and is the driving force to form a local ordered structure, meanwhile the transformed local ordered structure needs to satisfy the condition (Δ E{sub nn}/2 + Δ E{sub strain}) < 0 to be stabilized. Understanding the chemical and strain parts of enthalpy of mixing is helpful to design a new metallic glass with a good glass forming ability. Moreover, two types of metallic glasses (i.e., “strain dominant” and “chemical dominant”) are classified according to the relative importance between chemical effect and strain effect, which enriches our knowledge of the forming mechanism of metallic glass. Finally, a soft sphere model is established, different from the common hard sphere model.

  16. Microcalorimetric measurement of reaction enthalpies in solutions of uranium and neptunium compounds

    SciTech Connect (OSTI)

    Schreiner, F.; Friedman, A.M.; Richards, R.R.; Sullivan, J.C.

    1984-01-01

    The formation of complexes of uranyl and neptunyl(VI) ions with carbonate and hydrogen carbonate has been studied by titration microcalorimetry. The measurements were carried out with a computer-controlled microcalorimeter which is described in detail. Sample volumes are typically in the range of 1.5 to 2.5 ccm, containing about 0.05 millimole of the ionic species to be studied. The small volume renders the calorimeter useful for the measurement of uncommon and strongly radioactive substances. Enthalpies of reaction were obtained for the formation of the dicarbonato and the tricarbonato uranyl ions in a sulfate medium of ionic strength 1.6. The enthalpies are ..delta..H/sub 2/ = -39.6 +- 1 kJ/mol and -57.5 +- 1.5 kJ/mol, respectively. The titration data for the neptunyl(VI) - carbonate system yield a value of -50 +- 2 kJ/mol for the tricarbonato-neptunyl ion when interpreted in analogy to the uranyl system.

  17. Thermal dissociation behavior and dissociation enthalpies of methane-carbon dioxide mixed hydrates

    SciTech Connect (OSTI)

    Kwon, T.H.; Kneafsey, T.J.; Rees, E.V.L.

    2011-02-15

    Replacement of methane with carbon dioxide in hydrate has been proposed as a strategy for geologic sequestration of carbon dioxide (CO{sub 2}) and/or production of methane (CH{sub 4}) from natural hydrate deposits. This replacement strategy requires a better understanding of the thermodynamic characteristics of binary mixtures of CH{sub 4} and CO{sub 2} hydrate (CH{sub 4}-CO{sub 2} mixed hydrates), as well as thermophysical property changes during gas exchange. This study explores the thermal dissociation behavior and dissociation enthalpies of CH{sub 4}-CO{sub 2} mixed hydrates. We prepared CH{sub 4}-CO{sub 2} mixed hydrate samples from two different, well-defined gas mixtures. During thermal dissociation of a CH{sub 4}-CO{sub 2} mixed hydrate sample, gas samples from the head space were periodically collected and analyzed using gas chromatography. The changes in CH{sub 4}-CO{sub 2} compositions in both the vapor phase and hydrate phase during dissociation were estimated based on the gas chromatography measurements. It was found that the CO{sub 2} concentration in the vapor phase became richer during dissociation because the initial hydrate composition contained relatively more CO{sub 2} than the vapor phase. The composition change in the vapor phase during hydrate dissociation affected the dissociation pressure and temperature; the richer CO{sub 2} in the vapor phase led to a lower dissociation pressure. Furthermore, the increase in CO{sub 2} concentration in the vapor phase enriched the hydrate in CO{sub 2}. The dissociation enthalpy of the CH{sub 4}-CO{sub 2} mixed hydrate was computed by fitting the Clausius-Clapeyron equation to the pressure-temperature (PT) trace of a dissociation test. It was observed that the dissociation enthalpy of the CH{sub 4}-CO{sub 2} mixed hydrate lays between the limiting values of pure CH{sub 4} hydrate and CO{sub 2} hydrate, increasing with the CO{sub 2} fraction in the hydrate phase.

  18. Determination of enthalpies of formation of energetic molecules with composite quantum chemical methods

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Manaa, M. Riad; Fried, Laurence E.; Kuo, I-Feng W.

    2016-02-01

    We report gas-phase enthalpies of formation for the set of energetic molecules NTO, DADE, LLM-105, TNT, RDX, TATB, HMX, and PETN using the G2, G3, G4, and ccCA-PS3 quantum composite methods. Calculations for HMX and PETN hitherto represent the largest molecules attempted with these methods. G3 and G4 calculations are typically close to one another, with a larger difference found between these methods and ccCA-PS3. Furthermore there is significant uncertainty in experimental values, the mean absolute deviation between the average experimental value and calculations are 12, 6, 7, and 3 kcal/mol for G2, G3, G4, and ccCA-PS3, respectively.

  19. Computational Study of Bond Dissociation Enthalpies for Substituted $\\beta$-O-4 Lignin Model Compounds

    SciTech Connect (OSTI)

    Younker, Jarod M; Beste, Ariana; Buchanan III, A C

    2011-01-01

    The biopolymer lignin is a potential source of valuable chemicals. Phenethyl phenyl ether (PPE) is representative of the dominant $\\beta$-O-4 ether linkage. Density functional theory (DFT) is used to calculate the Boltzmann-weighted carbon-oxygen and carbon-carbon bond dissociation enthalpies (BDEs) of substituted PPE. These values are important in order to understand lignin decomposition. Exclusion of all conformers that have distributions of less than 5\\% at 298 K impacts the BDE by less than 1 kcal mol$^{-1}$. We find that aliphatic hydroxyl/methylhydroxyl substituents introduce only small changes to the BDEs (0-3 kcal mol$^{-1}$). Substitution on the phenyl ring at the $ortho$ position substantially lowers the C-O BDE, except in combination with the hydroxyl/methylhydroxyl substituents, where the effect of methoxy substitution is reduced by hydrogen bonding. Hydrogen bonding between the aliphatic substituents and the ether oxygen in the PPE derivatives has a significant influence on the BDE. CCSD(T)-calculated BDEs and hydrogen bond strengths of $ortho$-substituted anisoles when compared with M06-2X values confirm that the latter method is sufficient to describe the molecules studied and provide an important benchmark for lignin model compounds.

  20. ENTHALPY-BASED THERMAL EVOLUTION OF LOOPS. II. IMPROVEMENTS TO THE MODEL

    SciTech Connect (OSTI)

    Cargill, P. J.; Bradshaw, S. J.; Klimchuk, J. A.

    2012-06-20

    This paper develops the zero-dimensional (0D) hydrodynamic coronal loop model 'Enthalpy-based Thermal Evolution of Loops' (EBTEL) proposed by Klimchuk et al., which studies the plasma response to evolving coronal heating, especially impulsive heating events. The basis of EBTEL is the modeling of mass exchange between the corona and transition region (TR) and chromosphere in response to heating variations, with the key parameter being the ratio of the TR to coronal radiation. We develop new models for this parameter that now include gravitational stratification and a physically motivated approach to radiative cooling. A number of examples are presented, including nanoflares in short and long loops, and a small flare. The new features in EBTEL are important for accurate tracking of, in particular, the density. The 0D results are compared to a 1D hydro code (Hydrad) with generally good agreement. EBTEL is suitable for general use as a tool for (1) quick-look results of loop evolution in response to a given heating function, (2) extensive parameter surveys, and (3) situations where the modeling of hundreds or thousands of elemental loops is needed. A single run takes a few seconds on a contemporary laptop.

  1. Economic Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Development Economic Development Los Alamos is committed to investing and partnering in economic development initiatives and programs that have a positive impact to stimulate business growth that creates jobs and strengthens communities in Northern New Mexico. September 20, 2013 R&M Construction from Santa Clara Pueblo is a 2015 Native American Venture Acceleration Fund recipient. R&M Construction from Santa Clara Pueblo is a 2015 Native American Venture Acceleration Fund

  2. Economic Performance

    Energy Savers [EERE]

    in Environmental, Energy, and Economic Performance ... of greenhouse gas emissions a priority for Federal agencies, it is hereby ordered as follows: Section 1. Policy. ...

  3. ECONOMIC DISPATCH

    Broader source: Energy.gov (indexed) [DOE]

    ... Load forecasting As noted in the Department's November 2005 Economic Dispatch Report, improving the quality and accuracy of load forecasting would improve the reliability and cost-...

  4. Economics | NISAC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Posted by Admin on Mar 1, 2012 in | Comments 0 comments NISAC Agent-Based Laboratory for Economics (N-ABLE(tm)) NISAC has developed N-ABLE(tm) to assist federal decision makers in ...

  5. Economic Impact

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Impact on New Mexico Delivering the best possible science and technology results for the nation while making a positive impact on our New Mexico communities and economy July 1, 2016 Contacts Community Partnerships Kathy Keith (505) 665-4400 Email Economic Development Vangie Trujillo (505) 665-4284 Email Market Transition Program Micheline Devaurs (505) 665-9090 Email Small Business Program Chris Fresquez (505) 667-4419 Email Positive impact on New Mexico's economy, communities Through

  6. Dual surface interferometer

    DOE Patents [OSTI]

    Pardue, Robert M.; Williams, Richard R.

    1982-01-01

    A double-pass interferometer is provided which allows direct measurement of relative displacement between opposed surfaces. A conventional plane mirror interferometer may be modified by replacing the beam-measuring path cube-corner reflector with an additional quarter-wave plate. The beam path is altered to extend to an opposed plane mirrored surface and the reflected beam is placed in interference with a retained reference beam split from dual-beam source and retroreflected by a reference cube-corner reflector mounted stationary with the interferometer housing. This permits direct measurement of opposed mirror surfaces by laser interferometry while doubling the resolution as with a conventional double-pass plane mirror laser interferometer system.

  7. Dual surface interferometer

    DOE Patents [OSTI]

    Pardue, R.M.; Williams, R.R.

    1980-09-12

    A double-pass interferometer is provided which allows direct measurement of relative displacement between opposed surfaces. A conventional plane mirror interferometer may be modified by replacing the beam-measuring path cube-corner reflector with an additional quarterwave plate. The beam path is altered to extend to an opposed plane mirrored surface and the reflected beam is placed in interference with a retained reference beam split from dual-beam source and retroreflected by a reference cube-corner reflector mounted stationary with the interferometer housing. This permits direct measurement of opposed mirror surfaces by laser interferometry while doubling the resolution as with a conventional double-pass plane mirror laser interferometer system.

  8. Dual Tank Fuel System

    SciTech Connect (OSTI)

    Wagner, Richard William; Burkhard, James Frank; Dauer, Kenneth John

    1999-11-16

    A dual tank fuel system has primary and secondary fuel tanks, with the primary tank including a filler pipe to receive fuel and a discharge line to deliver fuel to an engine, and with a balance pipe interconnecting the primary tank and the secondary tank. The balance pipe opens close to the bottom of each tank to direct fuel from the primary tank to the secondary tank as the primary tank is filled, and to direct fuel from the secondary tank to the primary tank as fuel is discharged from the primary tank through the discharge line. A vent line has branches connected to each tank to direct fuel vapor from the tanks as the tanks are filled, and to admit air to the tanks as fuel is delivered to the engine.

  9. The CPA Equation of State and an Activity Coefficient Model for Accurate Molar Enthalpy Calculations of Mixtures with Carbon Dioxide and Water/Brine

    SciTech Connect (OSTI)

    Myint, P. C.; Hao, Y.; Firoozabadi, A.

    2015-03-27

    Thermodynamic property calculations of mixtures containing carbon dioxide (CO2) and water, including brines, are essential in theoretical models of many natural and industrial processes. The properties of greatest practical interest are density, solubility, and enthalpy. Many models for density and solubility calculations have been presented in the literature, but there exists only one study, by Spycher and Pruess, that has compared theoretical molar enthalpy predictions with experimental data [1]. In this report, we recommend two different models for enthalpy calculations: the CPA equation of state by Li and Firoozabadi [2], and the CO2 activity coefficient model by Duan and Sun [3]. We show that the CPA equation of state, which has been demonstrated to provide good agreement with density and solubility data, also accurately calculates molar enthalpies of pure CO2, pure water, and both CO2-rich and aqueous (H2O-rich) mixtures of the two species. It is applicable to a wider range of conditions than the Spycher and Pruess model. In aqueous sodium chloride (NaCl) mixtures, we show that Duan and Suns model yields accurate results for the partial molar enthalpy of CO2. It can be combined with another model for the brine enthalpy to calculate the molar enthalpy of H2O-CO2-NaCl mixtures. We conclude by explaining how the CPA equation of state may be modified to further improve agreement with experiments. This generalized CPA is the basis of our future work on this topic.

  10. Economic impact

    SciTech Connect (OSTI)

    Technology Transfer Department

    2001-06-01

    In federal fiscal year 2000 (FY00), Berkeley Lab had 4,347 full- and part-time employees. In addition, at any given time of the year, there were more than 1,000 Laboratory guests. These guests, who also reside locally, have an important economic impact on the nine-county Bay Area. However, Berkeley Lab's total economic impact transcends the direct effects of payroll and purchasing. The direct dollars paid to the Lab's employees in the form of wages, salaries, and benefits, and payments made to contractors for goods and services, are respent by employees and contractors again and again in the local and greater economy. Further, while Berkeley Lab has a strong reputation for basic scientific research, many of the Lab's scientific discoveries and inventions have had direct application in industry, spawning new businesses and creating new opportunities for existing firms. This analysis updates the Economic Impact Analysis done in 1996, and its purpose is to describe the economic and geographic impact of Laboratory expenditures and to provide a qualitative understanding of how Berkeley Lab impacts and supports the local community. It is intended as a guide for state, local, and national policy makers as well as local community members. Unless otherwise noted, this analysis uses data from FY00, the most recent year for which full data are available.

  11. Dual flapper valve assembly

    SciTech Connect (OSTI)

    Clary, S.R.; Giusti, F. Jr.; Sproul, R.M.

    1989-07-11

    This patent describes a dual flapper valve assembly for limiting the loss of completion fluid in connection with a well service operation. The valve assembly consists of: tubular support means defining a flow passage; a first flapper valve assembly connected in series flow relation with the support means, the first flapper valve assembly having a valve closure member movable between first and second positions for closing and opening the flow passage; a second flapper valve assembly connected in series flow relation in the support means, the second flapper valve assembly having a valve closure member movable between open and closed passage positions for closing and opening the flow passage; a prop sleeve mounted within the support means, the prop sleeve being movable from an extended position in which it props the closure member of one flapper valve in the open passage position to a retracted position in which the closure member is disengaged and released for movement to the closed passage position, the valve closure member of one of the flapper valve assemblies being engageable by a wash pipe extending through the flow passage to prop the valve closure member in the open passage position, and being movable to the closed passage position upon retraction of the wash pipe out of the flow passage.

  12. Fuel economizer

    SciTech Connect (OSTI)

    Zwierzelewski, V.F.

    1984-06-26

    A fuel economizer device for use with an internal combustion engine fitted with a carburetor is disclosed. The fuel economizer includes a plate member which is mounted between the carburetor and the intake portion of the intake manifold. The plate member further has at least one aperture formed therein. One tube is inserted through the at least one aperture in the plate member. The one tube extends longitudinally in the passage of the intake manifold from the intake portion toward the exit portion thereof. The one tube concentrates the mixture of fuel and air from the carburetor and conveys the mixture of fuel and air to a point adjacent but spaced away from the inlet port of the internal combustion engine.

  13. ECONOMIC IMPACT

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ECONOMIC IMPACT 2015 SANDIA NATIONAL LABORATORIES National Security Sandia's primary mission is ensuring the U.S. nuclear arsenal is safe, secure, and reliable, and can fully support our nation's deterrence policy. NUCLEAR WEAPONS DEFENSE SYSTEMS & ASSESSMENTS We provide technical solutions for global security by engineering and integrating advanced science and technology to help defend and protect the United States. Jill Hruby President and Laboratories Director "Qualified, diverse

  14. Economics of ethanol fuel for crop production

    SciTech Connect (OSTI)

    Fontana, C.; Rotz, C.A.

    1982-07-01

    A computer model was developed to simulate conventional and ethanol fuel consumption for crop production. The model was validated by obtaining a close comparison between simulated and actual diesel requirements for farms in Michigan. Parameters for ethanol consumption were obtained from laboratory tests using total fueling of spark-ignition engines and dual-fueling of diesel engines with ethanol. Ethanol fuel will always be more economically used in spark-ignition engines than in dual-fueled diesel engines. The price of gasoline must inflate at least 14 percent/year greater than that of ethanol and diesel must inflate at least 23 percent/year more than ethanol to allow economic use of ethanol as tractor fuel within the next 5 years. (Refs. 13).

  15. Ecological economizer

    SciTech Connect (OSTI)

    Peterson, E.M.

    1992-06-16

    This patent describes an engine economizer system adapted to supply an internal combustion engine with a heated air and water vapor mixture. It comprises a containment vessel, the vessel having: water level control means, an engine coolant fluid circuit, an engine lubricant circuit, an elongated air passage, air disbursement means, a water reservoir, air filter means, a vacuum aspiration port, and engine induction means associated with one of the carburetor and intake manifold and adapted to draw in the heated air and water vapor mixture by means of a hose connection to the aspiration port.

  16. Activation energy and enthalpy of decomposition for the Fe{sub 17}Sm{sub 2} nitride

    SciTech Connect (OSTI)

    Cabral, F.A.; Gama, S.; Ribeiro, C.A.

    1997-04-01

    Decomposition studies of the Fe{sub 17}Sm{sub 2}N{sub 3} compound were done using a Calvet-type microcalorimeter and a simultaneous gravimetric and differential thermal analyzer (DTA). The results show that the decomposition has onset temperature of 570{degree}C and proceeds up to 900{degree}C, and presents only one well determined exothermic thermal event. The calorimetric measurement shows that the enthalpy associated with the decomposition is 69 kJ/mol. The activation energy of the process was also determined using the Kissinger method applied to the DTA signal. It was observed that there was only one activation energy for the decomposition process, with a value of 339 kJ/mol. {copyright} {ital 1997 American Institute of Physics.}

  17. Dual porosity gas evolving electrode

    DOE Patents [OSTI]

    Townsend, C.W.

    1994-11-15

    A dual porosity electrode is described for use in thermoelectrochemical systems where simultaneous transport of gas and liquid into and/or out of the electrode is required. The electrode includes catalytic electrode particles having diameters ranging from about 25 to 100 angstroms. The catalytic electrode particles are anchored to a support network in clusters which have internal pores ranging in size from 25 to 100 angstroms. The pores between the clusters range in size from between about 1 to 20 microns. A method for making the dual porosity electrodes is also disclosed.

  18. Dual porosity gas evolving electrode

    DOE Patents [OSTI]

    Townsend, Carl W.

    1994-01-01

    A dual porosity electrode for use in thermoelectrochemical systems where simultaneous transport of gas and liquid into and/or out of the electrode is required. The electrode includes catalytic electrode particles having diameters ranging from about 25 to 100 angstroms. The catalytic electrode particles are anchored to a support network in clusters which have internal pores ranging in size from 25 to 100 angstroms. The pores between the clusters range in size from between about 1 to 20 microns. A method for making the dual porosity electrodes is also disclosed.

  19. UWB dual burst transmit driver

    DOE Patents [OSTI]

    Dallum, Gregory E.; Pratt, Garth C.; Haugen, Peter C.; Zumstein, James M.; Vigars, Mark L.; Romero, Carlos E.

    2012-04-17

    A dual burst transmitter for ultra-wideband (UWB) communication systems generates a pair of precisely spaced RF bursts from a single trigger event. An input trigger pulse produces two oscillator trigger pulses, an initial pulse and a delayed pulse, in a dual trigger generator. The two oscillator trigger pulses drive a gated RF burst (power output) oscillator. A bias driver circuit gates the RF output oscillator on and off and sets the RF burst packet width. The bias driver also level shifts the drive signal to the level that is required for the RF output device.

  20. Formation enthalpies and heat capacities of rear earth titanates: RE{sub 2}TiO{sub 5} (RE=La, Nd and Gd)

    SciTech Connect (OSTI)

    Hayun, Shmuel; Navrotsky, Alexandra

    2012-03-15

    The formation enthalpies and heat capacities of orthorhombic rare earth titanates, RE{sub 2}TiO{sub 5} (RE=La, Nd and Gd), have been studied by high temperature differential scanning calorimetry (300-1473 K) and oxide-melt solution calorimetry. The RE{sub 2}TiO{sub 5} samples are stable in enthalpy with respect to their oxides and the pyrochlore RE{sub 2}Ti{sub 2}O{sub 7} phase. The general trend that has been demonstrated in other RE-ternary systems; decreasing thermodynamic stability with decreasing R{sub A}/R{sub B} was found to be valid for the RE{sub 2}TiO{sub 5}, and their enthalpies of formation from oxides become more negative with increasing RE{sup 3+} ionic radius. - Graphical abstract: Normalized enthalpy of formation for one RE{sup 3+} cation from the oxides for several RE ternary oxide systems vs. the cation radius ratio R{sub A}/R{sub B} (A=RE, B=Ti, Zr, P). All the RE ternary oxide systems are stable relative to constituent oxides, with increasing stability as R{sub A}/R{sub B} increases. The Roman numerals above the cations represent the coordination number. Highlights: Black-Right-Pointing-Pointer Formation enthalpies and heat capacities of RE{sub 2}TiO{sub 5} (RE=La, Nd and Gd) were determined. Black-Right-Pointing-Pointer Enthalpies of formation of RE{sub 2}TiO{sub 5} from oxides become more negative with increasing RE{sup 3+} ionic radius. Black-Right-Pointing-Pointer RE{sub 2}TiO{sub 5} phases are stable in enthalpy with respect to their oxides and the pyrochlore RE{sub 2}Ti{sub 2}O{sub 7} phases. Black-Right-Pointing-Pointer Thermodynamic stability of orthorhombic RE{sub 2}TiO{sub 5} decrease with increasing R{sub B} to R{sub A} ratio.

  1. Dual shell pressure balanced vessel

    DOE Patents [OSTI]

    Fassbender, Alexander G.

    1992-01-01

    A dual-wall pressure balanced vessel for processing high viscosity slurries at high temperatures and pressures having an outer pressure vessel and an inner vessel with an annular space between the vessels pressurized at a pressure slightly less than or equivalent to the pressure within the inner vessel.

  2. Dual function conducting polymer diodes

    DOE Patents [OSTI]

    Heeger, Alan J.; Yu, Gang

    1996-01-01

    Dual function diodes based on conjugated organic polymer active layers are disclosed. When positively biased the diodes function as light emitters. When negatively biased they are highly efficient photodiodes. Methods of preparation and use of these diodes in displays and input/output devices are also disclosed.

  3. Economic Considerations of Nuclear Desalination in Korea

    SciTech Connect (OSTI)

    Man-Ki, Lee; Seung-Su, Kim

    2006-07-01

    The objective of this study is to assess the economics of SMART (System-integrated Modular Advanced Reactor) desalination plant in Korea through DEEP (Devaluation Economic Evaluation Program). SMART is mainly designed for the dual purpose of producing water and electricity with the total capacity of 100 MWe which 10 MWe is used for water production and the remains for the electric generation. SMART desalination plant using MED (Multi-Effect Distillation) process is in the stage of the commercial development and its cost information is also being accumulated. In this circumstances, the economic assessment of nuclear desalination by SMART and the effect of water(or electric) supply price to the regional economy is meaningful to the policy maker. This study is focused on the case study analysis about the economics of SMART desalination plant and the meanings of the case study result. This study is composed of two parts. One is prepared to survey the methodology regarding cost allocation between electricity and water in DEEP and the other is for the economic assessment of SMART. The cost allocation methods that have been proposed or used can be classified into two main groups, one is the cost prorating method and the other is the credit method. The cost of an product item in the dual-purpose plant can be determined differently depending on the costing methods adopted. When it comes to applying credit method adopted in this thesis, the production cost of water depends on what kind of the power cost will be chosen in calculating the power credit. This study also analyses the changes of nuclear desalination economics according to the changes of the important factors such as fossil fuel price. I wish that this study can afford to give an insight to the policy maker about SMART desalination plant. (authors)

  4. Dual arm master controller concept

    SciTech Connect (OSTI)

    Kuban, D.P.; Perkins, G.S.

    1984-01-01

    The Advanced Servomanipulator (ASM) slave was designed with an anthropomorphic stance, gear/torque tube power drives, and modular construction. These features resulted in increased inertia, friction, and backlash relative to tape-driven manipulators. Studies were performed which addressed the human factors design and performance trade-offs associated with the corresponding master controller best suited for the ASM. The results of these studies, as well as the conceptual design of the dual arm master controller, are presented. 6 references, 3 figures.

  5. Subcontracted R and D final report: SRC-I phase equilibrium and enthalpy data for coal liquefaction and solvent recovery areas. Vol. 3

    SciTech Connect (OSTI)

    Mehta, D.C.; Chu, I.C.; Kidnay, A.J.; Yesavage, V.F.

    1984-03-01

    The Enthalpy Program was a 20-month project initiated on January 18, 1982 by the International Coal Refining Company (ICRC) and under the technical direction of Professor Arthur J. Kidnay and Professor V.F. Yesavage at the Colorado School of Mines (CSM), Golden, Colorado. The objective of the program was to gather enthalpy data on representative pure model compounds, mixtures of model compounds, and selected coal-derived liquid samples furnished by ICRC. A copy of the technical agreement between ICRC and CSM is included in this report as Appendix A. This final report contains a complete description of the calorimeter and the experimental procedures used, separate data sections for each experimental task, and a copy of the technical agreement between ICRC and CSM. Data are presented for 11 coal liquid fractions. Each section of this report is organized to stand alone; thus, there are no general lists of references, tables of notation, or overall data tables.

  6. Dual Functional Cathode Additives for Battery Technologies -...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Return to Search Dual Functional Cathode Additives for Battery Technologies Brookhaven ... activation of the cell of a lithium battery having a primary metal sulfide additive ...

  7. Confinement of quarks in dual superconductor models

    SciTech Connect (OSTI)

    Ripka, Georges

    2005-06-14

    We review some aspects and problems of quark confinement models which are based on a dual super-conductor description of the QCD vacuum.

  8. Dual Axis Radiographic Hydrodynamic Test Facility | National...

    National Nuclear Security Administration (NNSA)

    Dual Axis Radiographic Hydrodynamic Test Facility An integral part of the national ... radiographic images of the imploding test object, in which materials are moving at ...

  9. The Aerodynamic, Dual- Wavelength Optical Spectrometer

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Aerodynamic, Dual- Wavelength Optical Spectrometer James C. Wilson Mechanical and ... 467. * Aerodynamic Particle Sizing - Wilson J.C., Liu B.Y.H., "Aerodynamic Particle ...

  10. Low and high Temperature Dual Thermoelectric Generation Waste...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and high Temperature Dual Thermoelectric Generation Waste Heat Recovery System for Light-Duty Vehicles Low and high Temperature Dual Thermoelectric Generation Waste Heat Recovery System ...

  11. Development of Dual-Gated Bilayer Graphene Device Structures...

    Office of Scientific and Technical Information (OSTI)

    Development of Dual-Gated Bilayer Graphene Device Structures. Citation Details In-Document Search Title: Development of Dual-Gated Bilayer Graphene Device Structures. Abstract not ...

  12. Project Profile: Sensible Heat, Direct, Dual-Media Thermal Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Sensible Heat, Direct, Dual-Media Thermal Energy Storage Module Project Profile: Sensible Heat, Direct, Dual-Media Thermal Energy Storage Module Acciona logo Acciona Solar, under ...

  13. Method and system for dual resolution translation stage (Patent...

    Office of Scientific and Technical Information (OSTI)

    The dual resolution stage also includes an adjustable pivot block mechanically coupled to the stage assembly. The adjustable pivot block includes a pivot shaft. The dual resolution ...

  14. Project Profile: Indirect, Dual-Media, Phase Changing Material...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Indirect, Dual-Media, Phase Changing Material Modular Thermal Energy Storage System Project Profile: Indirect, Dual-Media, Phase Changing Material Modular Thermal Energy Storage ...

  15. POLICY GUIDANCE MEMORANDUM #11A Approval Process for Dual Compensation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    POLICY GUIDANCE MEMORANDUM 11A Approval Process for Dual Compensation Waivers for Reemployed Annuitants Process to grant dual compensation (salary-offset) waivers to reemployed ...

  16. DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility DARHT, supports a critical component of LANL's primary mission: to...

  17. Dual manifold heat pipe evaporator

    DOE Patents [OSTI]

    Adkins, Douglas R. (Albuquerque, NM); Rawlinson, K. Scott (Albuquerque, NM)

    1994-01-01

    An improved evaporator section for a dual manifold heat pipe. Both the upper and lower manifolds can have surfaces exposed to the heat source which evaporate the working fluid. The tubes in the tube bank between the manifolds have openings in their lower extensions into the lower manifold to provide for the transport of evaporated working fluid from the lower manifold into the tubes and from there on into the upper manifold and on to the condenser portion of the heat pipe. A wick structure lining the inner walls of the evaporator tubes extends into both the upper and lower manifolds. At least some of the tubes also have overflow tubes contained within them to carry condensed working fluid from the upper manifold to pass to the lower without spilling down the inside walls of the tubes.

  18. Dual manifold heat pipe evaporator

    DOE Patents [OSTI]

    Adkins, D.R.; Rawlinson, K.S.

    1994-01-04

    An improved evaporator section is described for a dual manifold heat pipe. Both the upper and lower manifolds can have surfaces exposed to the heat source which evaporate the working fluid. The tubes in the tube bank between the manifolds have openings in their lower extensions into the lower manifold to provide for the transport of evaporated working fluid from the lower manifold into the tubes and from there on into the upper manifold and on to the condenser portion of the heat pipe. A wick structure lining the inner walls of the evaporator tubes extends into both the upper and lower manifolds. At least some of the tubes also have overflow tubes contained within them to carry condensed working fluid from the upper manifold to pass to the lower without spilling down the inside walls of the tubes. 1 figure.

  19. Economic Impact | Jefferson Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Impact Jefferson Lab generates many economic benefits. For the nation, Jefferson Lab generates $679.1 million in economic output and 4,422 jobs. The economic output and related jobs represent the potential loss of gross output and employment that would be felt by the country if the lab suddenly were to vanish. For the Commonwealth of Virginia, Jefferson Lab generates $271.1 million in economic output and 2,200 jobs. For the Hampton Roads area, the lab creates an economic benefit in the

  20. Economic Development Office

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Development Office Is your technology business looking for a door to the Laboratory? The Economic Development Office at PNNL is here to help you start, grow, or relocate...

  1. Dual control active superconductive devices

    DOE Patents [OSTI]

    Martens, Jon S.; Beyer, James B.; Nordman, James E.; Hohenwarter, Gert K. G.

    1993-07-20

    A superconducting active device has dual control inputs and is constructed such that the output of the device is effectively a linear mix of the two input signals. The device is formed of a film of superconducting material on a substrate and has two main conduction channels, each of which includes a weak link region. A first control line extends adjacent to the weak link region in the first channel and a second control line extends adjacent to the weak link region in the second channel. The current flowing from the first channel flows through an internal control line which is also adjacent to the weak link region of the second channel. The weak link regions comprise small links of superconductor, separated by voids, through which the current flows in each channel. Current passed through the control lines causes magnetic flux vortices which propagate across the weak link regions and control the resistance of these regions. The output of the device taken across the input to the main channels and the output of the second main channel and the internal control line will constitute essentially a linear mix of the two input signals imposed on the two control lines. The device is especially suited to microwave applications since it has very low input capacitance, and is well suited to being formed of high temperature superconducting materials since all of the structures may be formed coplanar with one another on a substrate.

  2. Cogeneration: Economic and technical analysis. (Latest citations from the NTIS bibliographic database). Published Search

    SciTech Connect (OSTI)

    1995-12-01

    The bibliography contains citations concerning economic and technical analysis of cogeneration systems. Topics include electric power and steam generation, dual-purpose and fuel cell power plants, and on-site power generation. Tower focus power plants, solar cogeneration, biomass conversion, coal liquefaction and gasification, and refuse derived fuels are examined. References cite feasibility studies, performance and economic evaluation, environmental impacts, and institutional factors. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  3. Cogeneration: Economic and technical analysis. (Latest citations from the NTIS data base). Published Search

    SciTech Connect (OSTI)

    Not Available

    1992-05-01

    The bibliography contains citations concerning economic and technical analysis of cogeneration systems. Topics include electric power and steam generation, dual-purpose and fuel cell power plants, and on-site power generation. Tower focus power plants, solar cogeneration, biomass conversion, coal liquefaction and gasification, and refuse derived fuels are discussed. References cite feasibility studies, performance and economic evaluation, environmental impacts, and institutional factors. (Contains 250 citations and includes a subject term index and title list.)

  4. Cogeneration: Economic and technical analysis. (Latest citations from the NTIS Bibliographic database). Published Search

    SciTech Connect (OSTI)

    Not Available

    1993-12-01

    The bibliography contains citations concerning economic and technical analysis of cogeneration systems. Topics include electric power and steam generation, dual-purpose and fuel cell power plants, and on-site power generation. Tower focus power plants, solar cogeneration, biomass conversion, coal liquefaction and gasification, and refuse derived fuels are examined. References cite feasibility studies, performance and economic evaluation, environmental impacts, and institutional factors. (Contains 250 citations and includes a subject term index and title list.)

  5. Cogeneration: Economic and technical analysis. (Latest citations from the NTIS bibliographic database). Published Search

    SciTech Connect (OSTI)

    Not Available

    1993-09-01

    The bibliography contains citations concerning economic and technical analysis of cogeneration systems. Topics include electric power and steam generation, dual-purpose and fuel cell power plants, and on-site power generation. Tower focus power plants, solar cogeneration, biomass conversion, coal liquefaction and gasification, and refuse derived fuels are examined. References cite feasibility studies, performance and economic evaluation, environmental impacts, and institutional factors. (Contains 250 citations and includes a subject term index and title list.)

  6. Cogeneration: Economic and technical analysis. (Latest citations from the NTIS Bibliographic database). Published Search

    SciTech Connect (OSTI)

    Not Available

    1994-11-01

    The bibliography contains citations concerning economic and technical analysis of cogeneration systems. Topics include electric power and steam generation, dual-purpose and fuel cell power plants, and on-site power generation. Tower focus power plants, solar cogeneration, biomass conversion, coal liquefaction and gasification, and refuse derived fuels are examined. References cite feasibility studies, performance and economic evaluation, environmental impacts, and institutional factors. (Contains 250 citations and includes a subject term index and title list.)

  7. Economic impact of climate

    SciTech Connect (OSTI)

    Eddy, A.

    1980-05-01

    This volume summarizes the first two of a series of six workshops to investigate the economic impact of climate. These two workshops dealt mainly with input-output and econometric models. Potential for introducing weather and climate variables was discussed. A listing of topics and authors follows: Economic Models and the Identification of Climatic Effects on Economic Processes, Stan Johnson; Economic Modeling, Jim Morgan; Econometric Modeling: State of the Arts for the US Agricultural Industry, Abner Womack; Regional Input-Output Models: Understanding Their Application, Charles Lamphear; Measuring Regional Economic Impact Associated With Unfavorable Conditions During Crop Production Periods: A concept Paper, Charles Lamphear; Possible Applications of Input-Output Models in Climatic Impact Analysis, William Cooter; and Aspects of Input-Output Analysis Pertinent to Climate-Economic Modeling: Three Short Notes, William Cooter. (PSB)

  8. Economic Values | Open Energy Information

    Open Energy Info (EERE)

    Economic Values Jump to: navigation, search Retrieved from "http:en.openei.orgwindex.php?titleEconomicValues&oldid612356...

  9. SWAMC Economic Summit

    Broader source: Energy.gov [DOE]

    The 27th Annual Southwest Alaska Economic Summit and Business Meeting is a three-day conference covering energy efficiency planning, information on Alaska programs, and more.

  10. Wind Economic Development (Postcard)

    SciTech Connect (OSTI)

    Not Available

    2011-08-01

    The U.S. Department of Energy's Wind Powering America initiative provides information on the economic development benefits of wind energy. This postcard is a marketing piece that stakeholders can provide to interested parties; it will guide them to the economic development benefits section on the Wind Powering America website.

  11. Dual-domain point diffraction interferometer

    DOE Patents [OSTI]

    Naulleau, Patrick P.; Goldberg, Kenneth Alan

    2000-01-01

    A hybrid spatial/temporal-domain point diffraction interferometer (referred to as the dual-domain PS/PDI) that is capable of suppressing the scattered-reference-light noise that hinders the conventional PS/PDI is provided. The dual-domain PS/PDI combines the separate noise-suppression capabilities of the widely-used phase-shifting and Fourier-transform fringe pattern analysis methods. The dual-domain PS/PDI relies on both a more restrictive implementation of the image plane PS/PDI mask and a new analysis method to be applied to the interferograms generated and recorded by the modified PS/PDI. The more restrictive PS/PDI mask guarantees the elimination of spatial-frequency crosstalk between the signal and the scattered-light noise arising from scattered-reference-light interfering with the test beam. The new dual-domain analysis method is then used to eliminate scattered-light noise arising from both the scattered-reference-light interfering with the test beam and the scattered-reference-light interfering with the "true" pinhole-diffracted reference light. The dual-domain analysis method has also been demonstrated to provide performance enhancement when using the non-optimized standard PS/PDI design. The dual-domain PS/PDI is essentially a three-tiered filtering system composed of lowpass spatial-filtering the test-beam electric field using the more restrictive PS/PDI mask, bandpass spatial-filtering the individual interferogram irradiance frames making up the phase-shifting series, and bandpass temporal-filtering the phase-shifting series as a whole.

  12. Dual waveband compact catadioptric imaging spectrometer

    DOE Patents [OSTI]

    Chrisp, Michael P.

    2012-12-25

    A catadioptric dual waveband imaging spectrometer that covers the visible through short-wave infrared, and the midwave infrared spectral regions, dispersing the visible through shortwave infrared with a zinc selenide grating and midwave infrared with a sapphire prism. The grating and prism are at the cold stop position, enabling the pupil to be split between them. The spectra for both wavebands are focused onto the relevant sections of a single dual waveband detector. Spatial keystone distortion is controlled to less than one tenth of a pixel over the full wavelength range, facilitating the matching of the spectra in the midwave infrared with the shorter wavelength region.

  13. Combustion and Emissions Performance of Dual-Fuel Gasoline and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Combustion and Emissions Performance of Dual-Fuel Gasoline and Diesel HECC on a Multi-Cylinder Light Duty Diesel Engine Combustion and Emissions Performance of Dual-Fuel Gasoline ...

  14. A Universal Dual-Fuel Controller for OEM/Aftermarket Diesel Engineswith Comprehensive Fuel & Emission Control

    Broader source: Energy.gov [DOE]

    Presents a universal dual fuel ratio controller designed to control the fueling and emissions of dual fuel systems

  15. Coupled dual loop absorption heat pump

    DOE Patents [OSTI]

    Sarkisian, Paul H.; Reimann, Robert C.; Biermann, Wendell J.

    1985-01-01

    A coupled dual loop absorption system which utilizes two separate complete loops. Each individual loop operates at three temperatures and two pressures. This low temperature loop absorber and condenser are thermally coupled to the high temperature loop evaporator, and the high temperature loop condenser and absorber are thermally coupled to the low temperature generator.

  16. Tribal Economic Outlook Conference

    Broader source: Energy.gov [DOE]

    Hosted by Northern Arizona University, the Tribal Economic Outlook Conference will preview the conditions that will impact business and economy in the year ahead. Hear what the experts are predicting for 2016 at the tribal, state, and local level.

  17. SWAMC Economic Summit

    Broader source: Energy.gov [DOE]

    Hosted by the Southwest Alaska Municipal Conference (SWAMC), the 27th Annual Southwest Alaska Economic Summit and Business Meeting is a three-day conference covering energy efficiency planning,...

  18. Techno-Economic Analysis

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Economic Analysis: Water splitting technologies and metrics Brian James Cassidy Houchins Daniel DeSantis Advanced Water Splitting Materials Workshop Stanford University 4/14/2016 Strategic Analysis Inc. Arlington VA Overview * Overview of H2A * Past H2A techno-economic analyses of water splitting technologies - High Temperature Solid Oxide Electrolysis Cell (SOEC) - Photoelectrochemical (PEC) - Solar Thermochemical Hydrogen (STCH) * System and Component Metrics - Tiered technology metrics *

  19. Regional Economic Development

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Regional Economic Development Regional Economic Development Supporting companies in every stage of development through access to technology, technical assistance or investment Questions Richard P. Feynman Center for Innovation Regional Programs (505) 665-9090 New Mexico Small Business Assistance Email Venture Acceleration Fund Email DisrupTECH Email SBIR/STTR Email FCI facilitates commercialization in New Mexico to accelerate and enhance our efforts to convert federal and state research

  20. Renewable Energy Economic Potential

    Broader source: Energy.gov [DOE]

    The report describes a geospatial analysis method to estimate the economic potential of several renewable resources available for electricity generation in the United States. Economic potential, one measure of renewable generation potential, is defined in this report as the subset of the available resource technical potential where the cost required to generate the electricity (which determines the minimum revenue requirements for development of the resource) is below the revenue available in terms of displaced energy and displaced capacity.

  1. Conflict Between Economic

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Conflict Between Economic Growth and Environmental Protection Dr. Brian Czech Advancement - Steady State Economy Monday, Jan 9, 2012 - 4:15PM MBG AUDITORIUM Refreshments at 4:00PM The confict between economic growth and environmental protection may not be reconciled via technological progress. The fundamentality of the confict ultimately boils down to laws of thermodynamics. Physicists and other scholars from the physical sciences are urgently needed for helping the public and policy makers

  2. Modular synthesis of a dual metal-dual semiconductor nano-heterostructure

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Amirav, Lilac; Oba, Fadekemi; Aloni, Shaul; Alivisatos, A. Paul

    2015-04-29

    Reported is the design and modular synthesis of a dual metal-dual semiconductor heterostructure with control over the dimensions and placement of its individual components. Analogous to molecular synthesis, colloidal synthesis is now evolving into a series of sequential synthetic procedures with separately optimized steps. Here we detail the challenges and parameters that must be considered when assembling such a multicomponent nanoparticle, and their solutions.

  3. Economical wind protection - underground

    SciTech Connect (OSTI)

    Kiesling, E.W.

    1980-01-01

    Earth-sheltered buildings inherently posess near-absolute occupant protection from severe winds. They should sustain no structural damage and only minimal facial damage. Assuming that the lower-hazard risk attendant to this type of construction results in reduced insurance-premium rates, the owner accrues economic benefits from the time of construction. Improvements to aboveground buildings, in contrast, may not yield early economic benefits in spite of a favorable benefit-to-cost ratio. This, in addition to sensitivity to initial costs, traditionalism in residential construction, and lack of professional input to design, impede the widespread use of underground improvements and the subsequent economic losses from severe winds. Going underground could reverse the trend. 7 references.

  4. Economic impacts study

    SciTech Connect (OSTI)

    Brunsen, W.; Worley, W.; Frost, E.

    1988-09-30

    This is a progress report on the first phase of a project to measure the economic impacts of a rapidly changing U.S. target base. The purpose of the first phase is to designate and test the macroeconomic impact analysis model. Criteria were established for a decision-support model. Additional criteria were defined for an interactive macroeconomic impact analysis model. After a review of several models, the Economic Impact Forecast System model of the U.S. Army Construction Research Laboratory was selected as the appropriate input-output tool that can address local and regional economic analysis. The model was applied to five test cases to demonstrate its utility and define possible revisions to meet project criteria. A plan for EIFS access was defined at three levels. Objectives and tasks for scenario refinement are proposed.

  5. Adaptive upscaling with the dual mesh method

    SciTech Connect (OSTI)

    Guerillot, D.; Verdiere, S.

    1997-08-01

    The objective of this paper is to demonstrate that upscaling should be calculated during the flow simulation instead of trying to enhance the a priori upscaling methods. Hence, counter-examples are given to motivate our approach, the so-called Dual Mesh Method. The main steps of this numerical algorithm are recalled. Applications illustrate the necessity to consider different average relative permeability values depending on the direction in space. Moreover, these values could be different for the same average saturation. This proves that an a priori upscaling cannot be the answer even in homogeneous cases because of the {open_quotes}dynamical heterogeneity{close_quotes} created by the saturation profile. Other examples show the efficiency of the Dual Mesh Method applied to heterogeneous medium and to an actual field case in South America.

  6. Dual shell pressure balanced reactor vessel. Final project report

    SciTech Connect (OSTI)

    Robertus, R.J.; Fassbender, A.G.

    1994-10-01

    The Department of Energy`s Office of Energy Research (OER) has previously provided support for the development of several chemical processes, including supercritical water oxidation, liquefaction, and aqueous hazardous waste destruction, where chemical and phase transformations are conducted at high pressure and temperature. These and many other commercial processes require a pressure vessel capable of operating in a corrosive environment where safety and economy are important requirements. Pacific Northwest Laboratory (PNL) engineers have recently developed and patented (U.S. patent 5,167,930 December 1, 1992) a concept for a novel Dual Shell Pressure Balanced Vessel (DSPBV) which could solve a number of these problems. The technology could be immediately useful in continuing commercialization of an R&D 100 award-winning technology, Sludge-to-oil Reactor System (STORS), originally developed through funding by OER. Innotek Corporation is a small business that would be one logical end-user of the DSPBV reactor technology. Innotek is working with several major U.S. engineering firms to evaluate the potential of this technology in the disposal of wastes from sewage treatment plants. PNL entered into a CRADA with Innotek to build a bench-scale demonstration reactor and test the system to advance the economic feasibility of a variety of high pressure chemical processes. Hydrothermal processing of corrosive substances on a large scale can now be made significantly safer and more economical through use of the DSPBV. Hydrothermal chemical reactions such as wet-air oxidation and supercritical water oxidation occur in a highly corrosive environment inside a pressure vessel. Average corrosion rates from 23 to 80 miles per year have been reported by Rice (1994) and Latanision (1993).

  7. Fabrication of dual porosity electrode structure

    DOE Patents [OSTI]

    Smith, James L.; Kucera, Eugenia H.

    1991-01-01

    A substantially entirely fibrous ceramic which may have dual porosity of both micro and macro pores. Total porosity may be 60-75% by volume. A method of spraying a slurry perpendicularly to an ambient stream of air is disclosed along with a method of removing binders without altering the fiber morphology. Adding fine ceramic particulates to the green ceramic fibers enhances the sintering characteristics of the fibers.

  8. dual-function | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Novel Dual Functional Membrane for Controlling Carbon Dioxide Emissions from Fossil Fueled Power Plants Project No.: FG26-04NT42120 Microstructure of the composite membrane Overview of the microstructure of the composite membrane comprising of: (1) a commericially available tubular or hollow fiber ceramic support; (2) a mesoporous surfactant-templated silica sub-layer with pore size 15-50 Å; and (3) a Microporous aminosilicate gas separation membrane layer with pore size 4-10 Å. This completed

  9. Dual Axis Radiographic Hydrodynamic Test Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DARHT DARHT Facility: A critical component of stockpile stewardship A new research frontier awaits! Our door is open and we thrive on mutually beneficial partnerships, collaborations that drive innovations and new technologies. April 12, 2012 Dominic Tafoya and Dave Honaberger prepare a refurbished DARHT (Dual Axis Radiographic Hydrotest Facility) 2nd axis accelerator cell for magnetic axis alignment measurements. Contact Group Leader Terry Priestley (505) 665-1330 Email Deputy Group Leader Tim

  10. Fabrication of dual porosity electrode structure

    DOE Patents [OSTI]

    Smith, J.L.; Kucera, E.H.

    1991-02-12

    A substantially entirely fibrous ceramic is described which may have dual porosity of both micro and macro pores. Total porosity may be 60-75% by volume. A method of spraying a slurry perpendicularly to an ambient stream of air is disclosed along with a method of removing binders without altering the fiber morphology. Adding fine ceramic particulates to the green ceramic fibers enhances the sintering characteristics of the fibers. 3 figures.

  11. Dual curvature acoustically damped concentrating collector. Final technical report

    SciTech Connect (OSTI)

    Smith, G.A.; Rausch, R.A.

    1980-05-01

    A development program was conducted to investigate the design and performance parameters of a novel, dual curvature, concentrating solar collector. The reflector of the solar collector is achieved with a stretched-film reflective surface that approximates a hyperbolic paraboloid and is capable of line-focusing at concentration ratios ranging from 10 to 20X. A prototype collector was designed based on analytical and experimental component trade-off activities as well as economic analyses of solar thermal heating and cooling systems incorporating this type of collector. A prototype collector incorporating six 0.66 x 1.22 m (2 x 4 ft) was fabricated and subjected to a limited thermal efficiency test program. A peak efficiency of 36% at 121/sup 0/C (250/sup 0/F) was achieved based upon the gross aperture area. Commercialization activities were conducted, including estimated production costs of $134.44/m/sup 2/ ($12.49/ft/sup 2/) for the collector assembly (including a local suntracker and controls) and $24.33/m/sup 2/ ($2.26/ft/sup 2/) for the reflector subassembly.

  12. Inorganic dual-layer microporous supported membranes

    DOE Patents [OSTI]

    Brinker, C. Jeffrey; Tsai, Chung-Yi; Lu, Yungfeng

    2003-03-25

    The present invention provides for a dual-layer inorganic microporous membrane capable of molecular sieving, and methods for production of the membranes. The inorganic microporous supported membrane includes a porous substrate which supports a first inorganic porous membrane having an average pore size of less than about 25 .ANG. and a second inorganic porous membrane coating the first inorganic membrane having an average pore size of less than about 6 .ANG.. The dual-layered membrane is produced by contacting the porous substrate with a surfactant-template polymeric sol, resulting in a surfactant sol coated membrane support. The surfactant sol coated membrane support is dried, producing a surfactant-templated polymer-coated substrate which is calcined to produce an intermediate layer surfactant-templated membrane. The intermediate layer surfactant-templated membrane is then contacted with a second polymeric sol producing a polymeric sol coated substrate which is dried producing an inorganic polymeric coated substrate. The inorganic polymeric coated substrate is then calcined producing an inorganic dual-layered microporous supported membrane in accordance with the present invention.

  13. First-principles studies of structural stabilities and enthalpies of formation of refractory intermetallics: TM and TM3 (T = Ti, Zr, Hf; M = Ru, Rh, Pd, Os, Ir, Pt)

    SciTech Connect (OSTI)

    Xing, Weiwei; Chen, X.; Li, Dianzhong; Li, Y. Y.; Fu, Chong Long; Meschel, S.

    2012-01-01

    Using first-principles local density functional approach, we have calculated the ground-state structural phase stabilities and enthalpies of formation of thirty-six binary transition-metal refractory TM and TM3 compounds formed by Group IV elements T (T = Ti, Zr, Hf) and platinum group elements M (M = Ru, Rh, Pd, Os, Ir, Pt) . We compared our results with the available experimental data and found good agreement between theory and experiment in both the trends of structural stabilities and the magnitudes of formation enthalpies. Moreover, based on our calculated results, an empirical relationship between cohesive energies ( E) and melting temperatures (Tm) was derived as Tm = 0.0292 E/kB (where kB is the Boltzmann constant) for both TM and TM3 compounds.

  14. Dual fueling of a Caterpillar 3406 diesel engine

    SciTech Connect (OSTI)

    Bell, S.R.; Midkiff, K.C.; Doughty, G.; Brett, C.E.

    1996-05-01

    A Caterpillar 3406 turbocharged diesel engine was converted to operate in a dual-fuel mode and was evaluated for performance and emission characteristics for both diesel and natural gas operation. Full load power was achieved with dual fueling without knock. Similar fuel efficiencies were obtained with dual fueling a high loads, but efficiencies were lower for low loads. Bosch smoke numbers were reduced by over 50% with dual fueling for all cases investigated. NO{sub x} emissions were found to be lower at low loads and at high speeds under high load. CO emissions were significantly increased for dual fueling while CO{sub 2} concentrations in the exhaust were reduced for dual fueling.

  15. DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility DARHT, supports a critical component of LANL's primary mission: to ensure the safety, security, and effectiveness of nuclear weapons in our nation's stockpile. Los Alamos scientists built DARHT, the world's most powerful x-ray machine, to analyze mockups of nuclear weapons. At the Los Alamos National Laboratory (LANL), the Dual-Axis Radiographic Hydrodynamic Test Facility, or DARHT,

  16. Establishing Economic Competitiveness

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Establishing Economic Competitiveness Energy storage technologies can transform electric systems operation by providing flexibility. This can improve the efficiency of electric system operation. For example, energy storage systems can smooth the otherwise variable production of renewable energy technologies and help shift the peak demand to reduce peak electric prices. Though energy storage technologies can be game-changing grid technology, they must inevitably compete with alternative

  17. WINDExchange: Wind Economic Development

    Wind Powering America (EERE)

    Development WINDExchange provides software applications and publications to help individuals, developers, local governments, and utilities make decisions about wind power. Projecting costs and benefits of new installations, including the economic development impacts created, is a key element in looking at potential wind applications. Communities, states, regions, job markets (i.e., construction, operations and maintenance), the tax base, tax revenues, and others can be positively affected. These

  18. Economic Development - SRSCRO

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Development As the designated Community Reuse Organization (CRO) for the Department of Energy's Savannah River Site, the Savannah River Site Community Reuse Organization (SRSCRO) is charged with the responsibility for developing and implementing a comprehensive plan to diversify the economy of the SRSCRO region. During its 50 year history, the Savannah River Site has supported America's national defense mission, contributing significantly to the successful end of the Cold War at the

  19. MTBE Production Economics

    Gasoline and Diesel Fuel Update (EIA)

    MTBE Production Economics Tancred C. M. Lidderdale Contents 1. Summary 2. MTBE Production Costs 3. Relationship between price of MTBE and Reformulated Gasoline 4. Influence of Natural Gas Prices on the Gasoline Market 5. Regression Results 6. Data Sources 7. End Notes 1. Summary Last year the price of MTBE (methyl tertiary butyl ether) increased dramatically on two occasions (Figure 1) (see Data Sources at end of article.): 1. Between April and June 2000, the price (U.S. Gulf Coast waterborne

  20. Gravity Duals of Lifshitz-Like Fixed Points (Journal Article...

    Office of Scientific and Technical Information (OSTI)

    This work can be considered a small step towards making useful dual descriptions of such critical points. Authors: Kachru, Shamit ; Stanford U., Phys. Dept. SLAC ; Liu, Xiao ; ...

  1. ARM: AOS: Dual Column Cloud Condensation Nuclei Counter (Dataset...

    Office of Scientific and Technical Information (OSTI)

    AOS: Dual Column Cloud Condensation Nuclei Counter Authors: Derek Hageman ; Bill Behrens ; Scott Smith ; Janek Uin ; Janek Uin ; Cynthia Salwen ; Cynthia Salwen ; Annette Koontz ; ...

  2. Method and system for dual resolution translation stage

    DOE Patents [OSTI]

    Halpin, John Michael

    2014-04-22

    A dual resolution translation stage includes a stage assembly operable to receive an optical element and a low resolution adjustment device mechanically coupled to the stage assembly. The dual resolution stage also includes an adjustable pivot block mechanically coupled to the stage assembly. The adjustable pivot block includes a pivot shaft. The dual resolution stage further includes a lever arm mechanically coupled to the adjustable pivot block. The lever arm is operable to pivot about the pivot shaft. The dual resolution stage additionally includes a high resolution adjustment device mechanically coupled to the lever arm and the stage assembly.

  3. Dual initiation strip charge apparatus and methods for making...

    Office of Scientific and Technical Information (OSTI)

    A Dual Initiation Strip Charge (DISC) apparatus is initiated by a single initiation source and detonates a strip of explosive charge at two separate contacts. The reflection of ...

  4. Characterization of Dual-Fuel Reactivity Controlled Compression...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (RCCI) Using Hydrated Ethanol and Diesel Fuel Characterization of Dual-Fuel Reactivity Controlled Compression Ignition (RCCI) Using Hydrated Ethanol and Diesel Fuel This study ...

  5. A dual mass flux framework for boundary layer convection

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A dual mass flux framework for boundary layer convection Neggers, Roel European Centre for Medium-range Weather Forecasts (ECMWF) Category: Modeling A new convective boundary layer...

  6. Cogeneration: Economics and politics

    SciTech Connect (OSTI)

    Prince, R.G.H.; Poole, M.L.

    1996-12-31

    Cogeneration is a well established process for supplying heat and electricity from a single fuel source. Its feasibility and implementation in any particular case depend on technical, economic and internal and external {open_quotes}cultural{close_quotes} factors, including government policies. This paper describes the current status of small scale industrial cogeneration in Australia. A model has been developed to analyse the technical and economic aspects of retrofitting gas turbine cogeneration in the size range 3 to 30MW to industrial sites. The model demonstrates that for typical Australian energy cost data, the payback and the size of the optimized cogeneration plant depend strongly on electricity buyback prices. Also reviewed are some of the {open_quotes}cultural{close_quotes} factors which often militate against an otherwise economic installation, and government policies which may retard cogeneration by concern about local air emissions or favor it as increasing efficiency of energy use and reducing greenhouse emissions. A case study of a small gas turbine plant in Australia is outlined. 2 refs., 2 figs.

  7. Dual stage active magnetic regenerator and method

    DOE Patents [OSTI]

    Pecharsky, V.K.; Gschneidner, K.A. Jr.

    1999-03-30

    A dual stage active magnetic regenerator refrigerator as well as method using the Joule-Brayton thermodynamic cycle includes a high temperature stage refrigerant comprising DyAl{sub 2} or (Dy{sub 1{minus}x}Er{sub x})Al{sub 2} where x is selected to be greater than 0 and less than about 0.3 in combination with a low temperature stage comprising (Dy{sub 1{minus}x}Er{sub x})Al{sub 2} where x is selected to be greater than about 0.5 and less than 1 to provide significantly improved refrigeration efficiency in the liquefaction of gaseous hydrogen. 17 figs.

  8. Dual stage active magnetic regenerator and method

    DOE Patents [OSTI]

    Pecharsky, Vitalij K.; Gschneidner, Jr., Karl A.

    1999-03-30

    A dual stage active magnetic regenerator refrigerator as well as method using the Joule-Brayton thermodynamic cycle includes a high temperature stage refrigerant comprising DyAl.sub.2 or (Dy.sub.1-x Er.sub.x)Al.sub.2 where x is selected to be greater than 0 and less than about 0.3 in combination with a low temperature stage comprising (Dy.sub.1-x Er.sub.x)Al.sub.2 where x is selected to be greater than about 0.5 and less than 1 to provide significantly improved refrigeration efficiency in the liquefaction of gaseous hydrogen.

  9. Arctic Economics Model

    Energy Science and Technology Software Center (OSTI)

    1995-03-01

    AEM (Arctic Economics Model) for oil and gas was developed to provide an analytic framework for understanding the arctic area resources. It provides the capacity for integrating the resource and technology information gathered by the arctic research and development (R&D) program, measuring the benefits of alternaive R&D programs, and providing updated estimates of the future oil and gas potential from arctic areas. AEM enables the user to examine field or basin-level oil and gas recovery,more » costs, and economics. It provides a standard set of selected basin-specified input values or allows the user to input their own values. AEM consists of five integrated submodels: geologic/resource submodel, which distributes the arctic resource into 15 master regions, consisting of nine arctic offshore regions, three arctic onshore regions, and three souhtern Alaska (non-arctic) regions; technology submodel, which selects the most appropriate exploration and production structure (platform) for each arctic basin and water depth; oil and gas production submodel, which contains the relationship of per well recovery as a function of field size, production decline curves, and production decline curves by product; engineering costing and field development submodel, which develops the capital and operating costs associated with arctic oil and gas development; and the economics submodel, which captures the engineering costs and development timing and links these to oil and gas prices, corporate taxes and tax credits, depreciation, and timing of investment. AEM provides measures of producible oil and gas, costs, and ecomonic viability under alternative technology or financial conditions.« less

  10. Dual fuel control of a high speed turbocharged diesel engine

    SciTech Connect (OSTI)

    Few, P.C.; Sardari, P.

    1987-01-01

    The modification of a Ford 7600 turbocharged diesel engine to a dual fuel engine using methane as the supplementary fuel has been carried out. The paper describes the preliminary work of dual fuel control. Two systems are examined and their behaviour is presented.

  11. Tubular ceramic-carbonate dual-phase membranes and methods of manufacture thereof

    DOE Patents [OSTI]

    Lin, Jerry Y. S.; Ortiz-Landeros, Jose; Dong, Xue-Liang

    2016-05-03

    Embodiments for a tubular ceramic-carbonate dual-phase membrane and methods for manufacturing the tubular ceramic-carbonate dual-phase membrane are disclosed.

  12. Variables Affecting Economic Development of Wind Energy

    SciTech Connect (OSTI)

    Lantz, E.; Tegen, S.

    2008-02-01

    Report on the specific factors driving wind-power-related economic development and on the impact of specific economic development variables on new wind project economic benefits.

  13. Geothermal District Heating Economics

    Energy Science and Technology Software Center (OSTI)

    1995-07-12

    GEOCITY is a large-scale simulation model which combines both engineering and economic submodels to systematically calculate the cost of geothermal district heating systems for space heating, hot-water heating, and process heating based upon hydrothermal geothermal resources. The GEOCITY program simulates the entire production, distribution, and waste disposal process for geothermal district heating systems, but does not include the cost of radiators, convectors, or other in-house heating systems. GEOCITY calculates the cost of district heating basedmore » on the climate, population, and heat demand of the district; characteristics of the geothermal resource and distance from the distribution center; well-drilling costs; design of the distribution system; tax rates; and financial conditions.« less

  14. Dual liquid and gas chromatograph system

    DOE Patents [OSTI]

    Gay, Don D.

    1985-01-01

    A chromatographic system that utilizes one detection system for gas chromatographic and micro-liquid chromatographic determinations. The detection system is a direct-current, atmospheric-pressure, helium plasma emission spectrometer. The detector utilizes a non-transparent plasma source unit which contains the plasma region and two side-arms which receive effluents from the micro-liquid chromatograph and the gas chromatograph. The dual nature of this chromatographic system offers: (1) extreme flexibility in the samples to be examined; (2) extremely low sensitivity; (3) element selectivity; (4) long-term stability; (5) direct correlation of data from the liquid and gas samples; (6) simpler operation than with individual liquid and gas chromatographs, each with different detection systems; and (7) cheaper than a commercial liquid chromatograph and a gas chromatograph.

  15. Dual LED/incandescent security fixture

    DOE Patents [OSTI]

    Gauna, Kevin Wayne

    2005-06-21

    A dual LED and incandescent security lighting system uses a hybrid approach to LED illumination. It combines an ambient LED illuminator with a standard incandescent lamp on a motion control sensor. The LED illuminator will activate with the onset of darkness (daylight control) and typically remain on during the course of the night ("always on"). The LED illumination, typically amber, is sufficient to provide low to moderate level lighting coverage to the wall and ground area adjacent to and under the fixture. The incandescent lamp is integrated with a motion control circuit and sensor. When movement in the field of view is detected (after darkness), the incandescent lamp is switched on, providing an increased level of illumination to the area. Instead of an "always on" LED illuminator, the LEDs may also be switched off when the incandescent lamp is switched on.

  16. Dual-keel electrodynamic maglev system

    DOE Patents [OSTI]

    He, J.L.; Wang, Z.; Rote, D.M.; Coffey, H.T.; Hull, J.R.; Mulcahy, T.M.; Cal, Y.

    1996-12-24

    A propulsion and stabilization system is disclosed with a plurality of superconducting magnetic devices affixed to the dual-keels of a vehicle, where the superconducting magnetic devices produce a magnetic field when energized. The system also includes a plurality of figure-eight shaped null-flux coils affixed to opposing vertical sides of slots in a guideway. The figure-eight shaped null-flux coils are vertically oriented, laterally cross-connected in parallel, longitudinally connected in series, and continue the length of the vertical slots providing levitation and guidance force. An external power source energizes the figure-eight shaped null-flux coils to create a magnetic traveling wave that interacts with the magnetic field produced by the superconducting magnets to impart motion to the vehicle. 6 figs.

  17. Dual-keel electrodynamic maglev system

    DOE Patents [OSTI]

    He, Jianliang; Wang, Zian; Rote, Donald M.; Coffey, Howard T.; Hull, John R.; Mulcahy, Thomas M.; Cal, Yigang

    1996-01-01

    A propulsion and stabilization system with a plurality of superconducting magnetic devices affixed to the dual-keels of a vehicle, where the superconducting magnetic devices produce a magnetic field when energized. The system also includes a plurality of figure-eight shaped null-flux coils affixed to opposing vertical sides of slots in a guideway. The figure-eight shaped null-flux coils are vertically oriented, laterally cross-connected in parallel, longitudinally connected in series, and continue the length of the vertical slots providing levitation and guidance force. An external power source energizes the figure-eight shaped null-flux coils to create a magnetic traveling wave that interacts with the magnetic field produced by the superconducting magnets to impart motion to the vehicle.

  18. Dual power, constant speed electric motor system

    DOE Patents [OSTI]

    Kirschbaum, H.S.

    1984-07-31

    A dual capacity permanent split capacitor electric motor system is provided with a stator having main and auxiliary windings. The main stator winding includes two winding sections which are connected in parallel with each other and across a pair of line terminals while the auxiliary winding is connected in series with a capacitor to form a circuit branch which is connected between the line terminals for operation at a first output power level. Switching means are provided to reconnect the main stator winding sections in series with each other and in series with a second capacitor to form a circuit branch which is connected between the line terminals while the stator auxiliary winding is connected directly between the line terminals for operation at a second output power level. Automatic rotation reversal occurs when the motor switches from the first to the second output power level. 6 figs.

  19. Dual power, constant speed electric motor system

    DOE Patents [OSTI]

    Kirschbaum, Herbert S.

    1984-01-01

    A dual capacity permanent split capacitor electric motor system is provided with a stator having main and auxiliary windings. The main stator winding includes two winding sections which are connected in parallel with each other and across a pair of line terminals while the auxiliary winding is connected in series with a capacitor to form a circuit branch which is connected between the line terminals for operation at a first output power level. Switching means are provided to reconnect the main stator winding sections in series with each other and in series with a second capacitor to form a circuit branch which is connected between the line terminals while the stator auxiliary winding is connected directly between the line terminals for operation at a second output power level. Automatic rotation reversal occurs when the motor switches from the first to the second output power level.

  20. Dual-fueling turbocharged diesels with ethanol

    SciTech Connect (OSTI)

    Cruz, J.M.; Rotz, C.A.; Watson, D.H.

    1982-09-01

    Spray addition and carburetion methods were tested for dual-fueling a turbocharged, 65 kW diesel tractor. Approximately 30 percent of the fuel energy for the tractor was supplied by spraying ethanol into the intake air and about 46 percent by carburetion with little affect on the engine thermal efficiency. Further substitution of diesel fuel with ethanol was limited by knock. As the amount of ethanol fed into the engine was increased, ignition apparently changed from the steady burning process which normally occurs in a diesel engine to a rapid explosion which caused knock. The best fuel for the spray approach was a 50 percent ethanol/water solution and with the carburetor it was an 80 percent ethanol/water solution.

  1. Dual-fueling turbocharged diesels with ethanol

    SciTech Connect (OSTI)

    Cruz, J.M.; Rotz, C.A.; Watson, D.H.

    1982-09-01

    Spray addition and carburetion methods were tested for dual-fueling a turbocharged, 65 kW diesel tractor. Approximately 30 percent of the fuel energy for the tractor was supplied by spraying ethanol into the intake air and about 46 percent by carburetion with little affect on the engine thermal efficiency. Further substitution of diesel fuel with ethanol was limited by knock. As the amount of ethanol fed into the engine was increased, ignition apparently changed from the steady burning process which normally occurs in a diesel engine to a rapid explosion which caused knock. The best fuel for the spray approach was a 50 percent ethanol/water solution and with the carburetor it was an 80 percent ethanol/water solution. (Refs. 6).

  2. Dual liquid and gas chromatograph system

    DOE Patents [OSTI]

    Gay, D.D.

    A chromatographic system is described that utilizes one detection system for gas chromatographic and micro-liquid chromatographic determinations. The detection system is a direct-current, atmospheric-pressure, helium plasma emission spectrometer. The detector utilizes a nontransparent plasma source unit which contains the plasma region and two side-arms which receive effluents from the micro-liquid chromatograph and the gas chromatograph. The dual nature of this chromatographic system offers: (1) extreme flexibility in the samples to be examined; (2) extreme low sensitivity; (3) element selectivity; (4) long-term stability; (5) direct correlation of data from the liquid and gas samples; (6) simpler operation than with individual liquid and gas chromatographs, each with different detection systems; and (7) cheaper than a commercial liquid chromatograph and a gas chromatograph.

  3. Microelectromechanical dual-mass resonator structure

    DOE Patents [OSTI]

    Dyck, Christopher W.; Allen, James J.; Huber, Robert J.

    2002-01-01

    A dual-mass microelectromechanical (MEM) resonator structure is disclosed in which a first mass is suspended above a substrate and driven to move along a linear or curved path by a parallel-plate electrostatic actuator. A second mass, which is also suspended and coupled to the first mass by a plurality of springs is driven by motion of the first mass. Various modes of operation of the MEM structure are possible, including resonant and antiresonant modes, and a contacting mode. In each mode of operation, the motion induced in the second mass can be in the range of several microns up to more than 50 .mu.m while the first mass has a much smaller displacement on the order of one micron or less. The MEM structure has applications for forming microsensors that detect strain, acceleration, rotation or movement.

  4. Comments on shielding for dual energy accelerators

    SciTech Connect (OSTI)

    Rossi, M. C.; Lincoln, H. M.; Quarin, D. J.; Zwicker, R. D.

    2008-06-15

    Determination of shielding requirements for medical linear accelerators has been greatly facilitated by the publication of the National Council on Radiation Protection and Measurements (NCRP) latest guidelines on this subject in NCRP Report No. 151. In the present report the authors review their own recent experience with patient treatments on conventional dual energy linear accelerators to examine the various input parameters needed to follow the NCRP guidelines. Some discussion is included of workloads, occupancy, use factors, and field size, with the effects of intensity modulated radiotherapy (IMRT) treatments included. Studies of collimator settings showed average values of 13.1x16.2 cm{sup 2} for 6 MV and 14.1x16.8 cm{sup 2} for 18 MV conventional ports, and corresponding average unblocked areas of 228 and 254 cm{sup 2}, respectively. With an average of 77% of the field area unblocked, this gives a mean irradiated area of 196 cm{sup 2} for the 18 MV beam, which dominates shielding considerations for most dual energy machines. Assuming conservatively small room dimensions, a gantry bin angle of 18 deg. was found to represent a reasonable unit for tabulation of use factors. For conventional 18 MV treatments it was found that the usual treatment angles of 0, 90, 180, and 270 deg. were still favored, and use factors of 0.25 represent reasonable estimates for these beams. As expected, the IMRT fields (all at 6 MV) showed a high degree of gantry angle randomization, with no bin having a use factor in excess of 0.10. It is concluded that unless a significant number of patients are treated with high energy IMRT, the traditional use factors of 0.25 are appropriate for the dominant high energy beam.

  5. SRS Economic Impact Study - SRSCRO

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SRS Economic Impact Study The operations at Savannah River Site (SRS) create jobs, generate income, and contribute to the tax revenues across both South Carolina and Georgia. When economic multipliers are factored in, the economic ripple effect is enormous. Despite its significance in recent years, there has been little understanding beyond qualitative observations about the value of SRS's contributions to the region and what that impact means in quantifiable terms. Consequently, the SRSCRO

  6. economic hydrogen fuel cell vehicles

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    economic hydrogen fuel cell vehicles - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future ...

  7. Consider Installing a Condensing Economizer

    Broader source: Energy.gov [DOE]

    This tip sheet summarizes the benefits of condensing economizers and is part of a series of tip sheets on how to optimize an industrial steam system.

  8. The Economics of Micro Grids

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Blink-less UPS Go Electric Energy Arbitrage Energy Optimization Peak shaving Demand Response & Aggregation FACILITIES UTILITIES 4 Micro Grid Economics: 2 Examples Go Electric ...

  9. Magnetic fusion reactor economics

    SciTech Connect (OSTI)

    Krakowski, R.A.

    1995-12-01

    An almost primordial trend in the conversion and use of energy is an increased complexity and cost of conversion systems designed to utilize cheaper and more-abundant fuels; this trend is exemplified by the progression fossil fission {yields} fusion. The present projections of the latter indicate that capital costs of the fusion ``burner`` far exceed any commensurate savings associated with the cheapest and most-abundant of fuels. These projections suggest competitive fusion power only if internal costs associate with the use of fossil or fission fuels emerge to make them either uneconomic, unacceptable, or both with respect to expensive fusion systems. This ``implementation-by-default`` plan for fusion is re-examined by identifying in general terms fusion power-plant embodiments that might compete favorably under conditions where internal costs (both economic and environmental) of fossil and/or fission are not as great as is needed to justify the contemporary vision for fusion power. Competitive fusion power in this context will require a significant broadening of an overly focused program to explore the physics and simbiotic technologies leading to more compact, simplified, and efficient plasma-confinement configurations that reside at the heart of an attractive fusion power plant.

  10. Fuel reactivity effects on the efficiency and operational window of dual-fuel compression ignition engines

    SciTech Connect (OSTI)

    Splitter, Derek A; Reitz, Rolf

    2014-01-01

    Fuel reactivity effects on the efficiency and operational window of dual-fuel compression ignition engines

  11. EIS-0228: Dual Axis Radiographic Hydrodynamic Test (DARHT) Facility

    Broader source: Energy.gov [DOE]

    This EIS evaluates the potential environmental impact of a proposal to construct and operate the Dual Axis Radiographic Hydrodynamic Test (DARHT) facility at Los Alamos National Laboratory (LANL)...

  12. York Electric Cooperative- Dual Fuel Heat Pump Rebate Program

    Broader source: Energy.gov [DOE]

    York Electric Cooperative, Inc. (YEC) offers a $200 rebate to members who install a dual fuel heat pump in homes or businesses. The rebates are for primary residences, commercial, and industrial...

  13. Slant-hole collimator, dual mode sterotactic localization method

    DOE Patents [OSTI]

    Weisenberger, Andrew G.

    2002-01-01

    The use of a slant-hole collimator in the gamma camera of dual mode stereotactic localization apparatus allows the acquisition of a stereo pair of scintimammographic images without repositioning of the gamma camera between image acquisitions.

  14. NREL: Measurements and Characterization - Dual-Beam Sample Preparation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The FIB is equipped with a gas injection system (GIS) platinum metal deposition capability ... dual beam FIB showing nano deposition with GIS of Pt contacts to a single GaN nanowire. ...

  15. Parameterized reduced-order models using hyper-dual numbers....

    Office of Scientific and Technical Information (OSTI)

    This report presents a methodology for developing parameterized ROMs, which is based on Craig-Bampton component mode synthesis and the use of hyper-dual numbers to calculate the ...

  16. Competitive economics of nuclear power

    SciTech Connect (OSTI)

    Hellman, R.

    1981-03-02

    Some 12 components of a valid study of the competitive economics of a newly ordered nuclear power plant are identified and explicated. These are then used to adjust the original cost projections of four authoritative studies of nuclear and coal power economics.

  17. dual-phase-ceramic-asu | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Pre-Combustion Carbon Dioxide Capture by a New Dual-Phase Ceramic Carbonate Membrane Reactor Project No.: DE-FE0000470 Arizona State University is developing a dual-phase, membrane-based separation device which will separate carbon dioxide (CO2) from typical water gas shift (WGS) mixture feeds and produce hydrogen, which can be introduced into the combustion turbines of integrated gasification combined cycle (IGCC) plants. The objectives of the project are experimental studies of the synthesis

  18. Fuel cell having dual electrode anode or cathode

    DOE Patents [OSTI]

    Findl, Eugene

    1985-01-01

    A fuel cell that is characterized by including a dual electrode anode that is operable to simultaneously electro-oxidize a gaseous fuel and a liquid fuel. In alternative embodiments, a fuel cell having a single electrode anode is provided with a dual electrode cathode that is operable to simultaneously reduce a gaseous oxidant and a liquid oxidant to electro-oxidize a fuel supplied to the cell.

  19. Fuel cell having dual electrode anode or cathode

    DOE Patents [OSTI]

    Findl, E.

    1984-04-10

    A fuel cell that is characterized by including a dual electrode anode that is operable to simultaneously electro-oxidize a gaseous fuel and a liquid fuel. In alternative embodiments, a fuel cell having a single electrode anode is provided with a dual electrode cathode that is operable to simultaneously reduce a gaseous oxidant and a liquid oxidant to electro-oxidize a fuel supplied to the cell.

  20. Postmortem validation of breast density using dual-energy mammography

    SciTech Connect (OSTI)

    Molloi, Sabee Ducote, Justin L.; Ding, Huanjun; Feig, Stephen A.

    2014-08-15

    Purpose: Mammographic density has been shown to be an indicator of breast cancer risk and also reduces the sensitivity of screening mammography. Currently, there is no accepted standard for measuring breast density. Dual energy mammography has been proposed as a technique for accurate measurement of breast density. The purpose of this study is to validate its accuracy in postmortem breasts and compare it with other existing techniques. Methods: Forty postmortem breasts were imaged using a dual energy mammography system. Glandular and adipose equivalent phantoms of uniform thickness were used to calibrate a dual energy basis decomposition algorithm. Dual energy decomposition was applied after scatter correction to calculate breast density. Breast density was also estimated using radiologist reader assessment, standard histogram thresholding and a fuzzy C-mean algorithm. Chemical analysis was used as the reference standard to assess the accuracy of different techniques to measure breast composition. Results: Breast density measurements using radiologist reader assessment, standard histogram thresholding, fuzzy C-mean algorithm, and dual energy were in good agreement with the measured fibroglandular volume fraction using chemical analysis. The standard error estimates using radiologist reader assessment, standard histogram thresholding, fuzzy C-mean, and dual energy were 9.9%, 8.6%, 7.2%, and 4.7%, respectively. Conclusions: The results indicate that dual energy mammography can be used to accurately measure breast density. The variability in breast density estimation using dual energy mammography was lower than reader assessment rankings, standard histogram thresholding, and fuzzy C-mean algorithm. Improved quantification of breast density is expected to further enhance its utility as a risk factor for breast cancer.

  1. Project Profile: Indirect, Dual-Media, Phase Changing Material Modular

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Thermal Energy Storage System | Department of Energy Indirect, Dual-Media, Phase Changing Material Modular Thermal Energy Storage System Project Profile: Indirect, Dual-Media, Phase Changing Material Modular Thermal Energy Storage System Acciona logo Acciona Solar, under the Thermal Storage FOA, plans to design and validate a prototype and demonstrate a full-size (800 MWth) thermal energy storage (TES) system based on phase change materials (PCMs). Approach Acciona is using a test loop to

  2. Dual excitation acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, III, William B.

    1989-01-01

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in gelogical formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleous present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described.

  3. Dual excitation acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, W.B. III.

    1989-02-14

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in geological formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleons present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be performed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described. 6 figs.

  4. Dual mode stereotactic localization method and application

    DOE Patents [OSTI]

    Keppel, Cynthia E.; Barbosa, Fernando Jorge; Majewski, Stanislaw

    2002-01-01

    The invention described herein combines the structural digital X-ray image provided by conventional stereotactic core biopsy instruments with the additional functional metabolic gamma imaging obtained with a dedicated compact gamma imaging mini-camera. Before the procedure, the patient is injected with an appropriate radiopharmaceutical. The radiopharmaceutical uptake distribution within the breast under compression in a conventional examination table expressed by the intensity of gamma emissions is obtained for comparison (co-registration) with the digital mammography (X-ray) image. This dual modality mode of operation greatly increases the functionality of existing stereotactic biopsy devices by yielding a much smaller number of false positives than would be produced using X-ray images alone. The ability to obtain both the X-ray mammographic image and the nuclear-based medicine gamma image using a single device is made possible largely through the use of a novel, small and movable gamma imaging camera that permits its incorporation into the same table or system as that currently utilized to obtain X-ray based mammographic images for localization of lesions.

  5. Dual-domain lateral shearing interferometer

    DOE Patents [OSTI]

    Naulleau, Patrick P.; Goldberg, Kenneth Alan

    2004-03-16

    The phase-shifting point diffraction interferometer (PS/PDI) was developed to address the problem of at-wavelength metrology of extreme ultraviolet (EUV) optical systems. Although extremely accurate, the fact that the PS/PDI is limited to use with coherent EUV sources, such as undulator radiation, is a drawback for its widespread use. An alternative to the PS/PDI, with relaxed coherence requirements, is lateral shearing interferometry (LSI). The use of a cross-grating, carrier-frequency configuration to characterize a large-field 4.times.-reduction EUV lithography optic is demonstrated. The results obtained are directly compared with PS/PDI measurements. A defocused implementation of the lateral shearing interferometer in which an image-plane filter allows both phase-shifting and Fourier wavefront recovery. The two wavefront recovery methods can be combined in a dual-domain technique providing suppression of noise added by self-interference of high-frequency components in the test-optic wavefront.

  6. WINDExchange: Jobs and Economic Development Impact Models

    Wind Powering America (EERE)

    Deployment Activities Printable Version Bookmark and Share Regional Resource Centers Economic Development Jobs and Economic Development Impacts Model Resources & Tools Siting Jobs and Economic Development Impact Models JEDI: Jobs and Economic Development Impacts Model Fact Sheet PDF The Jobs and Economic Development Impact (JEDI) models are user-friendly tools that estimate the economic impacts of constructing and operating power generation at the local and state levels. Based on

  7. Transcript of Tribal Energy and Economic Webinar: Energy Planning for Tribal Economic Development

    Office of Energy Efficiency and Renewable Energy (EERE)

    Transcript for the Tribal Energy and Economic Webinar: Energy Planning for Tribal Economic Development held on Jan. 27, 2016.

  8. S-OO bond dissociation energies and enthalpies of formation of the thiomethyl peroxyl radicals CH{sub 3}S(O){sub n}OO (n=0,1,2)

    SciTech Connect (OSTI)

    Salta, Zoi; Kosmas, Agnie Mylona; Lesar, Antonija

    2014-10-06

    Optimized geometries, S-OO bond dissociation energies and enthalpies of formation for a series of thiomethyl peroxyl radicals are investigated using high level ab initio and density functional theory methods. The results show that the S-OO bond dissociation energy is largest in the methylsulfonyl peroxyl radical, CH{sub 3}S(O){sub 2}OO, which contains two sulfonic type oxygen atoms followed by the methylthiyl peroxyl radical, CH{sub 3}SOO. The methylsulfinyl peroxyl radical, CH{sub 3}S(O)OO, which contains only one sulfonic type oxygen shows the least stability with regard to dissociation to CH{sub 3}S(O)+O{sub 2}. This stabilization trend is nicely reflected in the variations of the S-OO bond distance which is found to be shortest in CH{sub 3}S(O){sub 2}OO and longest in CH{sub 3}S(O)OO.

  9. Renewable Energy: science, politics, and economics (Technical...

    Office of Scientific and Technical Information (OSTI)

    Renewable Energy: science, politics, and economics Citation Details In-Document Search Title: Renewable Energy: science, politics, and economics Authors: Migliori, Albert 1 + ...

  10. Economic, Energy, and Environmental Benefits of Concentrating...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic, Energy, and Environmental Benefits of Concentrating Solar Power in California L. ... NRELSR-550-39291 April 2006 Economic, Energy, and Environmental Benefits of ...

  11. PERI Green Economics | Open Energy Information

    Open Energy Info (EERE)

    PERI Green Economics Jump to: navigation, search Tool Summary LAUNCH TOOL Name: PERI Green Economics AgencyCompany Organization: Political Economy Research Institute Sector:...

  12. Travois Indian Country Affordable Housing & Economic Development...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Travois Indian Country Affordable Housing & Economic Development Conference Travois Indian Country Affordable Housing & Economic Development Conference April 4, 2016 8:00AM CDT to ...

  13. Chemical incident economic impact analysis methodology. (Technical...

    Office of Scientific and Technical Information (OSTI)

    Chemical incident economic impact analysis methodology. Citation Details In-Document Search Title: Chemical incident economic impact analysis methodology. You are accessing a ...

  14. Workforce and Economic Development | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Workforce and Economic Development Workforce and Economic Development Slides presented in the "What's Working in Residential Energy Efficiency Upgrade Programs Conference - ...

  15. Renewable Energy: science, politics, and economics (Technical...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Renewable Energy: science, politics, and economics Citation Details In-Document Search Title: Renewable Energy: science, politics, and economics You are ...

  16. Renewable Energy: science, politics, and economics (Technical...

    Office of Scientific and Technical Information (OSTI)

    Renewable Energy: science, politics, and economics Citation Details In-Document Search Title: Renewable Energy: science, politics, and economics You are accessing a document ...

  17. Dual-Fuel Truck Fleet: Start-Up Experience

    SciTech Connect (OSTI)

    NREL

    1998-09-30

    Although dual-fuel engine technology has been in development and limited use for several years, it has only recently moved toward full-scale operational capability for heavy-duty truck applications. Unlike a bifuel engine, which has two separate fuel systems that are used one at a time, a dual-fuel engine uses two fuel systems simultaneously. One of California's South Coast Air Quality Management District (SCAQMD) current programs is a demonstration of dual-fuel engine technology in heavy-duty trucks. These trucks are being studied as part of the National Renewable Energy Laboratory's (NREL's) Alternative Fuel Truck Program. This report describes the start-up experience from the program.

  18. Exploring Avionics Using Dual Cool Jets | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Exploring Next Generation Avionics Using Dual Cool Jets Click to email this to a friend (Opens in new window) Share on Facebook (Opens in new window) Click to share (Opens in new window) Click to share on LinkedIn (Opens in new window) Click to share on Tumblr (Opens in new window) Exploring Next Generation Avionics Using Dual Cool Jets Ankit Kalani 2015.08.12 Heat is a byproduct of operating electronics. If not managed properly, it can severely affect the reliability and performance of the

  19. Dual output acoustic wave sensor for molecular identification

    DOE Patents [OSTI]

    Frye, Gregory C.; Martin, Stephen J.

    1991-01-01

    A method of identification and quantification of absorbed chemical species by measuring changes in both the velocity and the attenuation of an acoustic wave traveling through a thin film into which the chemical species is sorbed. The dual output response provides two independent sensor responses from a single sensing device thereby providing twice as much information as a single output sensor. This dual output technique and analysis allows a single sensor to provide both the concentration and the identity of a chemical species or permits the number of sensors required for mixtures to be reduced by a factor of two.

  20. Dual fiber microprobe for mapping elemental distributions in biological cells

    DOE Patents [OSTI]

    Martin, Rodger C [Powell, TN; Martin, Madhavi Z [Powell, TN

    2007-07-31

    Laser-induced breakdown spectroscopy (LIBS) is applied on a microscale for in situ elemental analysis and spatial mapping in biological cells. A high power laser beam is focused onto a cell surface using a dual branching optical fiber probe for optical excitation of the cell constituents. Dual spectrometers and ICCD detectors capture the emission spectra from the excited cell(s). Repeated probing or repositioning of the laser beam with respect to the cell can provide 2-D or 3-D mapping of the cell.

  1. Dual design resistor for high voltage conditioning and transmission lines

    DOE Patents [OSTI]

    Siggins, Timothy Lynn; Murray, Charles W.; Walker, Richard L.

    2007-01-23

    A dual resistor for eliminating the requirement for two different value resistors. The dual resistor includes a conditioning resistor at a high resistance value and a run resistor at a low resistance value. The run resistor can travel inside the conditioning resistor. The run resistor is capable of being advanced by a drive assembly until an electrical path is completed through the run resistor thereby shorting out the conditioning resistor and allowing the lower resistance run resistor to take over as the current carrier.

  2. Control Strategy for a Dual Loop EGR System to Meet Euro 6 and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Control Strategy for a Dual Loop EGR System to Meet Euro 6 and Beyond Control Strategy for a Dual Loop EGR System to Meet Euro 6 and Beyond Presentation given at the 2009 DEER ...

  3. Dual-Axis Resonance Testing of Wind Turbine Blades - Energy Innovation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Return to Search Dual-Axis Resonance Testing of Wind Turbine Blades National Renewable ... of time needed to fatigue test wind turbine blades.
    Dual-axis testing can ...

  4. Dual role of Fe dopants in enhancing stability and charge transfer...

    Office of Scientific and Technical Information (OSTI)

    Dual role of Fe dopants in enhancing stability and charge transfer in ( Li 0.8 Fe 0.2 ) ... Title: Dual role of Fe dopants in enhancing stability and charge transfer in ( Li 0.8 Fe ...

  5. Toward large N thermal QCD from dual gravity: The heavy quarkonium...

    Office of Scientific and Technical Information (OSTI)

    Toward large N thermal QCD from dual gravity: The heavy quarkonium potential Citation Details In-Document Search Title: Toward large N thermal QCD from dual gravity: The heavy ...

  6. Development of Dual-Fuel Engine for Class 8 Applications | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dual-Fuel Engine for Class 8 Applications Development of Dual-Fuel Engine for Class 8 Applications Highlights roadmap towards 55% brake thermal efficiency and progress to meet ...

  7. TESTING OF THE DUAL ROTARY FILTER SYSTEM

    SciTech Connect (OSTI)

    Herman, D.; Fowley, M.; Stefanko, D.

    2011-08-29

    The Savannah River National Laboratory (SRNL) installed and tested two hydraulically connected SpinTek rotary microfilter (RMF) units to determine the behavior of a multiple filter system. Both units were successfully controlled by a control scheme written in DELTA-V architecture by Savannah River Remediation (SRR) Process Control Engineering personnel. The control system was tuned to provide satisfactory response to changing conditions during the operation of the multi-filter system. Stability was maintained through the startup and shutdown of one of the filter units while the second was still in operation. The installation configuration originally proposed by the Small Colum Ion Exchange (SCIX) project of independent filter and motor mountings may be susceptible to vibration. Significant stiffening of the filter and motor mounts was required to minimize the vibration. Alignment of the motor to the filter was a challenge in this test configuration. The deployment configuration must be easy to manipulate and allow for fine adjustment. An analysis of the vibration signature of the test system identified critical speeds. Whether it corresponds to the resonance frequency of a rotor radial vibration mode that was excited by rotor unbalance is uncertain based upon the measurements. A relative motion series should be completed on the filter with the final shaft configuration to determine if the resonances exist in the final filter design. The instrumentation selected for deployment, including the concentrate discharge control valve and flow meters, performed well. Automation of the valve control integrated well with the control scheme and when used in concert with the other control variables, allowed automated control of the dual RMF system. The one area of concern with the instrumentation was the condition resulting when the filtrate flow meter operated with less than three gpm. This low flow was at the lower range of performance for the flow meter. This should not be

  8. Alternative Fuels Data Center: Idaho National Laboratory Dual-Fuel Buses

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Reduce Operating Costs and Emissions Idaho National Laboratory Dual-Fuel Buses Reduce Operating Costs and Emissions to someone by E-mail Share Alternative Fuels Data Center: Idaho National Laboratory Dual-Fuel Buses Reduce Operating Costs and Emissions on Facebook Tweet about Alternative Fuels Data Center: Idaho National Laboratory Dual-Fuel Buses Reduce Operating Costs and Emissions on Twitter Bookmark Alternative Fuels Data Center: Idaho National Laboratory Dual-Fuel Buses Reduce Operating

  9. Low and high Temperature Dual Thermoelectric Generation Waste Heat Recovery System for Light-Duty Vehicles

    Office of Energy Efficiency and Renewable Energy (EERE)

    Developing a low and high temperature dual thermoelectric generation waste heat recovery system for light-duty vehicles.

  10. Considerations When Selecting a Condensing Economizer

    Broader source: Energy.gov [DOE]

    This tip sheet lays out considerations when selecting condensing economizers as part of optimized steam systems.

  11. BEST (Battery Economics for more Sustainable Transportation)

    Energy Science and Technology Software Center (OSTI)

    2009-12-31

    Computer software for the simulation of battery economics based on various transportation business models.

  12. A tandem-based compact dual-energy gamma generator

    SciTech Connect (OSTI)

    Persaud, A.; Kwan, J.W.; Leitner, M.; Leung, K.N.; Ludewigt, B.; Tanaka, N.; Waldron, W.; Wilde, S.; Antolak, A.J.; Morse, D.H.; Raber, T.

    2009-11-11

    A dual-energy tandem-type gamma generator has been developed at E.O. Lawrence Berkeley National Laboratory and Sandia National Laboratories. The tandem accelerator geometry allows higher energy nuclear reactions to be reached, thereby allowing more flexible generation of MeV-energy gammas for active interrogation applications.

  13. Differentially pumped dual linear quadrupole ion trap mass spectrometer

    DOE Patents [OSTI]

    Owen, Benjamin C.; Kenttamaa, Hilkka I.

    2015-10-20

    The present disclosure provides a new tandem mass spectrometer and methods of using the same for analyzing charged particles. The differentially pumped dual linear quadrupole ion trap mass spectrometer of the present disclose includes a combination of two linear quadrupole (LQIT) mass spectrometers with differentially pumped vacuum chambers.

  14. Dual Axis Radiographic Hydrodynamic Test | National Nuclear Security

    National Nuclear Security Administration (NNSA)

    Administration Dual Axis Radiographic Hydrodynamic Test NNSA releases Stockpile Stewardship Program quarterly experiments summary WASHIGTON, DC. - The National Nuclear Security Administration today released its current quarterly summary of experiments conducted as part of its science-based Stockpile Stewardship Program. The experiments carried out within the program are used in combination with complex computational models

  15. Dual aperture dipole magnet with second harmonic component

    DOE Patents [OSTI]

    Praeg, W.F.

    1983-08-31

    An improved dual aperture dipole electromagnet includes a second-harmonic frequency magnetic guide field winding which surrounds first harmonic frequency magnetic guide field windings associated with each aperture. The second harmonic winding and the first harmonic windings cooperate to produce resultant magnetic waveforms in the apertures which have extended acceleration and shortened reset portions of electromagnet operation.

  16. Dual aperture dipole magnet with second harmonic component

    DOE Patents [OSTI]

    Praeg, Walter F.

    1985-01-01

    An improved dual aperture dipole electromagnet includes a second-harmonic frequency magnetic guide field winding which surrounds first harmonic frequency magnetic guide field windings associated with each aperture. The second harmonic winding and the first harmonic windings cooperate to produce resultant magnetic waveforms in the apertures which have extended acceleration and shortened reset portions of electromagnet operation.

  17. Wrought stainless steels -- Dual marking and corrosion evaluation

    SciTech Connect (OSTI)

    Kobrin, G.; Lilly, J.; MacDiarmid, J.; Moniz, B.

    1999-10-01

    Prior to the 1980s, the commonly used type 300 austenitic series stainless steels (SS) in the chemical process industry were available in two grades: those with regular carbon content (straight grades) and those with extra-low carbon content (L-grades). When welding the straight grades, it was possible to sensitize the base metal adjacent to the weld. The carbon combines with the chromium at the grain boundaries, leaving a zone depleted of chromium, below the minimum required for SS, adjacent to the grain boundaries. Even a relatively mild corrosive environment then is able to selectively attack this region along grain boundaries. The dual-marked grades (types 304/304L and 316/316L) appeared, with the carbon content of an L-grade and the strength of a straight grade. Initially, there was no national code acceptance for dual marked grades. Designers were obliged to use L-grade stress values. To get around this, people were known to grind off the unacceptable part of the dual marking designation and deliver whatever grade was initially specified. ASME International now has formally stated that dual-marked grades may be used at straight grade stresses for all product forms and piping to 1,000 F (540 C).

  18. System-Level Logistics for Dual Purpose Canister Disposal

    SciTech Connect (OSTI)

    Kalinina, Elena A.

    2014-06-03

    The analysis presented in this report investigated how the direct disposal of dual purpose canisters (DPCs) may be affected by the use of standard transportation aging and disposal canisters (STADs), early or late start of the repository, and the repository emplacement thermal power limits. The impacts were evaluated with regard to the availability of the DPCs for emplacement, achievable repository acceptance rates, additional storage required at an interim storage facility (ISF) and additional emplacement time compared to the corresponding repackaging scenarios, and fuel age at emplacement. The result of this analysis demonstrated that the biggest difference in the availability of UNF for emplacement between the DPC-only loading scenario and the DPCs and STADs loading scenario is for a repository start date of 2036 with a 6 kW thermal power limit. The differences are also seen in the availability of UNF for emplacement between the DPC-only loading scenario and the DPCs and STADs loading scenario for the alternative with a 6 kW thermal limit and a 2048 start date, and for the alternatives with a 10 kW thermal limit and 2036 and 2048 start dates. The alternatives with disposal of UNF in both DPCs and STADs did not require additional storage, regardless of the repository acceptance rate, as compared to the reference repackaging case. In comparison to the reference repackaging case, alternatives with the 18 kW emplacement thermal limit required little to no additional emplacement time, regardless of the repository start time, the fuel loading scenario, or the repository acceptance rate. Alternatives with the 10 kW emplacement thermal limit and the DPCs and STADs fuel loading scenario required some additional emplacement time. The most significant decrease in additional emplacement time occurred in the alternative with the 6 kW thermal limit and the 2036 repository starting date. The average fuel age at emplacement ranges from 46 to 88 years. The maximum fuel age at

  19. A two-fold reduction in measurement time for neutron assay: Initial tests of a prototype dual-gated shift register

    SciTech Connect (OSTI)

    Stewart, J.E.; Bourret, S.C.; Krick, M.S.; Hansen, W.J.; Harker, W.C.

    1996-09-01

    Neutron coincidence counting (NCC) is used routinely around the world for nondestructive mass assay of uranium and plutonium in many forms, including waste. Compared with other methods, NCC is generally the most flexible, economic, and rapid. Many applications of NCC would benefit from a reduction in counting time required for a fixed random error. We have developed and tested the first prototype of a dual- gated, shift-register-based electronics unit that offers the potential of decreased measurement time for all passive and active NCC applications.

  20. Economics of a multimedia approach

    SciTech Connect (OSTI)

    Phillips, J.B.; Hindawi, M.A.

    1996-02-01

    One of the major driving forces in the decision of a facility operator to implement a multimedia approach to examining pollution is the economics of the situation. A multimedia approach has gained favor with many facility operators because it has been shown to be more cost-effective than dealing with a number of phases, or media, separately. To a great extent, this is due to elimination of inefficiencies involved with cross-media transfer of pollutants. Even more basic to the problem of industrial pollution is the generation of waste. All industrial processes yield some percentage of waste products, but frequently during the design phase the costs associated with producing wastes are underestimated. As part of this series on multimedia issues, the costs related to manufacturing waste products are examined in detail. An obvious inefficiency associated with waste generation is the loss of material that potentially could be converted to salable products. The value of commodity raw materials frequently is ignored when considering the total costs of pollution generation at an industrial facility. Although the economics of pollution generation are affected by a number of factors, including regulatory costs, disposal costs and impacts on health and safety, this article focuses on the economics of lost production in industrial facilities.

  1. Development and Use of the Dual-Mode Plasma Torch

    SciTech Connect (OSTI)

    Womack, R.; Shuey, M.

    2002-02-26

    After several years of development, a commercially available high-temperature treatment system has been developed and installed that treats heterogeneous low-level radioactive waste. High temperature plasma processing, unique torch design and operating features make it feasible to achieve a volume reduced, permanent, high integrity waste form while eliminating the personnel exposure and costs associated with conventional sorting, characterizing and handling. Plasma technology can also be used to treat previous conditioned waste packages that no longer meet the current acceptance criteria for final disposal. Plasma treatment can result, in many cases, in a substantial volume reduction, which lowers the final disposal costs. This paper covers the recently patented dual mode plasma torch design(1), the lessons learned that fostered its development and the advantages it brings to radioactive waste processing. This paper also provides current full scale Plasma Arc Centrifugal Treatment (PACT) project status and how the dual mode torch is being used in the PACT system.

  2. Dual Layer Monolith ATR of Pyrolysis Oil for Distributed Synthesis Gas Production

    SciTech Connect (OSTI)

    Lawal, Adeniyi

    2012-09-29

    We have successfully demonstrated a novel reactor technology, based on BASF dual layer monolith catalyst, for miniaturizing the autothermal reforming of pyrolysis oil to syngas, the second and most critical of the three steps for thermochemically converting biomass waste to liquid transportation fuel. The technology was applied to aged as well as fresh samples of pyrolysis oil derived from five different biomass feedstocks, namely switch-grass, sawdust, hardwood/softwood, golden rod and maple. Optimization of process conditions in conjunction with innovative reactor system design enabled the minimization of carbon deposit and control of the H2/CO ratio of the product gas. A comprehensive techno-economic analysis of the integrated process using in part, experimental data from the project, indicates (1) net energy recovery of 49% accounting for all losses and external energy input, (2) weight of diesel oil produced as a percent of the biomass to be ~14%, and (3) for a demonstration size biomass to Fischer-Tropsch liquid plant of ~ 2000 daily barrels of diesel, the price of the diesel produced is ~$3.30 per gallon, ex. tax. However, the extension of catalyst life is critical to the realization of the projected economics. Catalyst deactivation was observed and the modes of deactivation, both reversible and irreversible were identified. An effective catalyst regeneration strategy was successfully demonstrated for reversible catalyst deactivation while a catalyst preservation strategy was proposed for preventing irreversible catalyst deactivation. Future work should therefore be focused on extending the catalyst life, and a successful demonstration of an extended (> 500 on-stream hours) catalyst life would affirm the commercial viability of the process.

  3. Variables Affecting Economic Development of Wind Energy

    SciTech Connect (OSTI)

    Lantz, E.; Tegen, S.

    2008-07-01

    NREL's JEDI Wind model performed an analysis of wind-power-related economic development drivers. Economic development benefits for wind and coal were estimated using NREL's JEDI Wind and JEDI Coal models.

  4. Advanced regenerator testing in the Raytheon dual-use cryocoolerr

    SciTech Connect (OSTI)

    Schaefer, B. R.; Bellis, L.; Ellis, M. J.; Conrad, T. J.

    2014-01-29

    Significant progress has been made on the Raytheon low cost space cryocooler called the Dual-Use Cryocooler (DUC). Most notably, the DUC has been integrated and tested with an advanced regenerator. The advanced regenerator is a drop-in replacement for stainless steel screens and has shown significant thermodynamic performance improvements. This paper will compare the performance of two different regenerators and explain the benefits of the advanced regenerator.

  5. Dual-phase Cr-Ta alloys for structural applications

    DOE Patents [OSTI]

    Liu, Chain T.; Brady, Michael P.; Zhu, Jiahong; Tortorelli, Peter F.

    2001-01-01

    Dual phase alloys of chromium containing 2 to 11 atomic percent tantalum with minor amounts of Mo, Cr, Ti, Y, La, Cr, Si and Ge are disclosed. These alloys contain two phases including Laves phase and Cr-rich solid solution in either eutectic structures or dispersed Laves phase particles in the Cr-rich solid solution matrix. The alloys have superior mechanical properties at high temperature and good oxidation resistance when heated to above 1000.degree. C. in air.

  6. Retractable pin dual in-line package test clip

    DOE Patents [OSTI]

    Bandzuch, Gregory S.; Kosslow, William J.

    1996-01-01

    This invention is a Dual In-Line Package (DIP) test clip for use when troubleshooting circuits containing DIP integrated circuits. This test clip is a significant improvement over existing DIP test clips in that it has retractable pins which will permit troubleshooting without risk of accidentally shorting adjacent pins together when moving probes to different pins on energized circuits or when the probe is accidentally bumped while taking measurements.

  7. Dual fuel combustion in a turbocharged diesel engine

    SciTech Connect (OSTI)

    Few, P.C.; Newlyn, H.A.

    1987-01-01

    The modification of a turbocharged diesel engine to a dual-fuel engine using methane as the supplementary fuel has been carried out. The effect of the gaseous fuel in a turbo-charged diesel engine has been investigated by means of a heat release study and a computer program already developed at Leicester Polytechnic. It is used in order to examine the rate of heat released under any operational condition.

  8. Development of a high-output dual-fuel engine

    SciTech Connect (OSTI)

    Danyluk, P.R. . Fairbanks Morse Engineering Division)

    1993-10-01

    This paper presents the results of a new dual-fuel engine development program. The engine is the largest commercially available in terms of power output (650 hp/cyl) and features very low emissions (1 g/hp-hr NO[sub x]) and excellent fuel consumption (43 percent thermal efficiency). A two-cylinder turbocharged prototype was designed and built for the initial development. Results from testing on 18-cylinder production versions are also reported.

  9. Dual ion beam assisted deposition of biaxially textured template layers

    DOE Patents [OSTI]

    Groves, James R.; Arendt, Paul N.; Hammond, Robert H.

    2005-05-31

    The present invention is directed towards a process and apparatus for epitaxial deposition of a material, e.g., a layer of MgO, onto a substrate such as a flexible metal substrate, using dual ion beams for the ion beam assisted deposition whereby thick layers can be deposited without degradation of the desired properties by the material. The ability to deposit thicker layers without loss of properties provides a significantly broader deposition window for the process.

  10. Environmentally and Economically Beneficial Practices on Federal...

    Office of Environmental Management (EM)

    Environmentally and Economically Beneficial Practices on Federal Landscaped Grounds This Environmental Protection Agency report contains recommendations for a series of...

  11. Techno-Economic Modeling, Analysis, and Support

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Techno-Economic Modeling, Analysis, and Support - Sandia ... Transportation Energy Co-Evolution of Biofuels ... Biological and Environmental Research Collaborations ...

  12. Economic Impact Tools | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Economic Impact Tools Economic Impact Tools Photo of a well drilling rig. A man stands on the platform while another is climbing the rig. Technology Feasibility and Cost Analysis is performed to determine the potential economic viability of geothermal energy production and helps to identify which technologies have the greatest likelihood of economic success. Results from technology feasibility analysis efforts provide input to the Geothermal Technologies Office (GTO) research, development, and

  13. Economic Impacts and Business Opportunities | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Impacts and Business Opportunities NREL contributes to the local and national economy in various ways. We are one of the largest employers in Jefferson County, Colorado, and we provide business opportunities for small businesses and large corporations alike. Economic Impact The economic impact of NREL operations on the nation totaled $872 million and in Colorado, totaled $701 million in fiscal year 2014. NREL is a top ten employer in Jefferson County where the economic benefit totaled

  14. Integrated process and dual-function catalyst for olefin epoxidation

    DOE Patents [OSTI]

    Zhou, Bing (Cranbury, NJ); Rueter, Michael (Plymouth Meeting, PA)

    2003-01-01

    The invention discloses a dual-functional catalyst composition and an integrated process for production of olefin epoxides including propylene oxide by catalytic reaction of hydrogen peroxide from hydrogen and oxygen with olefin feeds such as propylene. The epoxides and hydrogen peroxide are preferably produced simultaneously in situ. The dual-functional catalyst comprises noble metal crystallites with dimensions on the nanometer scale (on the order of <1 nm to 10 nm), specially dispersed on titanium silicalite substrate particles. The dual functional catalyst catalyzes both the direct reaction of hydrogen and oxygen to generate hydrogen peroxide intermediate on the noble metal catalyst surface and the reaction of the hydrogen peroxide intermediate with the propylene feed to generate propylene oxide product. Combining both these functions in a single catalyst provides a very efficient integrated process operable below the flammability limits of hydrogen and highly selective for the production of hydrogen peroxide to produce olefin oxides such as propylene oxide without formation of undesired co-products.

  15. Economics of coal fines utilization

    SciTech Connect (OSTI)

    Hathi, V.; McHale, E.; Ramezan, M.; Winslow, J.

    1995-12-31

    In the twentieth century, coal has become the major fuel for electric power generation in the U.S. and most of the nonpetroleum-producing countries of the world. In 1998, the world coal-fired capacity for electric power generation was about 815 GW, consuming large quantities of coals of all ranks. Today, coal provides a third of the world`s energy requirements. In fact, coal use for power generation has grown steadily since the oil embargo in 1973 and has seen an even faster rate of growth in recent years. It has been reported that the global demand for new coal will increase by more than 1500 million tons by the year 2000. However, this increased production of coal has its drawbacks, including the concomitant production of coal waste. Reported estimates indicate that billions of tons of coal waste have already been disposed of in waste impoundments throughout the U.S. Further, in the U.S. today, about 20-25 % of each ton of mined coal is discarded by preparation plants as gob and plant tailings. It appears that the most economical near-term approach to coal waste recovery is to utilize the waste coal fines currently discarded with the refuse stream, rather than attempt to recover coal from waste impoundments that require careful prior evaluation and site preparation. A hypothetical circuit was designed to examine the economics of recovery and utilization of waste coal fines. The circuit recovers products from 100 tons per hour (tph) of coal waste feed recovering 70 tph of fine coal that can be used in coal-fired boilers. The present analysis indicates that the coal waste recovery is feasible and economical. In addition, significant environmental benefits can be expected.

  16. Economic viability of anaerobic digestion

    SciTech Connect (OSTI)

    Wellinger, A.

    1996-01-01

    The industrial application of anaerobic digestion is a relatively new, yet proven waste treatment technology. Anaerobic digestion reduces and upgrades organic waste, and is a good way to control air pollution as it reduces methane and nitrous gas emissions. For environmental and energy considerations, anaerobic digestion is a nearly perfect waste treatment process. However, its economic viability is still in question. A number of parameters - type of waste (solid or liquid), digester system, facility size, product quality and end use, environmental requirements, cost of alternative treatments (including labor), and interest rates - define the investment and operating costs of an anaerobic digestion facility. Therefore, identical facilities that treat the same amount and type of waste may, depending on location, legislation, and end product characteristics, reveal radically different costs. A good approach for evaluating the economics of anaerobic digestion is to compare it to treatment techniques such as aeration or conventional sewage treatment (for industrial wastewater), or composting and incineration (for solid organic waste). For example, the cost (per ton of waste) of in-vessel composting with biofilters is somewhat higher than that of anaerobic digestion, but the investment costs 1 1/2 to 2 times more than either composting or anaerobic digestion. Two distinct advantages of anaerobic digestion are: (1) it requires less land than either composting or incinerating, which translates into lower costs and milder environmental and community impacts (especially in densely populated areas); and (2) it produces net energy, which can be used to operate the facility or sold to nearby industries.

  17. Economic viability of anaerobic digestion

    SciTech Connect (OSTI)

    Wellinger, A.

    1995-11-01

    The industrial application of anaerobic digestion is a relatively new, yet proven waste treatment technology. Anaerobic digestion reduces and upgrades organic waste, and is a good way to control air pollution as it reduces methane and nitrous gas emissions. For environmental and energy considerations, anaerobic digestion is a nearly perfect waste treatment process. However, its economic viability is still in question. A number of parameters-type of waste (solid or liquid), digester system, facility size, product quality and end use, environmental requirements, cost of alternative treatments (including labor), and interest rates-define the investment and operating costs of anaerobic digestion facility. Therefore, identical facilities that treat the same amount and type of waste may, depending on location, legislation, and end product characteristics, reveal radically different costs. A good approach for evaluating the economics of anaerobic digestion is to compare it to treatment techniques such as aeration or conventional sewage treatment (for industrial wastewater), or composting and incineration (for solid organic waste). For example, the cost (per ton of waste) of in-vessel composting with biofilters in somewhat higher than that of anaerobic digestion, but the investment costs 11/2 to 2 times more than either composting or anaerobic digestion. Two distinct advantages of anaerobic digestion are: (1) it requires less land than either composting or incinerating, which translates into lower costs and milder environmental and community impacts (especially in densely populated areas); and (2) it produces net energy, which can be used to operate the facility or sold to nearby industries.

  18. Economic alternatives for containment barriers

    SciTech Connect (OSTI)

    Nicholson, P.J.; Jasperse, B.H.; Fisher, M.J.

    1997-12-31

    Fixation, barriers, and containment of existing landfills and other disposal areas are often performed by insitu auger type soil mixing and jet grouting. Cement or other chemical reagents are mixed with soil to form both vertical and horizontal barriers. Immobilization of contaminants can be economically achieved by mixing soil and the contaminants with reagents that solidify or stabilize the contaminated area. Developed in Japan, and relatively new to the United States, the first large scale application was for a vertical barrier at the Jackson Lake Dam project in 1986. This technology has grown in both the civil and environmental field since. The paper describes current United States practice for Deep Soil Mixing (over 12 meters in depth), and Shallow Soil Mixing for vertical barriers and stabilization/solidification, and Jet Grouting for horizontal and vertical barriers. Creating very low permeability barriers at depth with minimal surface return often makes these techniques economical when compared to slurry trenches. The paper will discuss equipment, materials, soil and strength parameters, and quality control.

  19. Iowa Department of Economic Development | Open Energy Information

    Open Energy Info (EERE)

    Department of Economic Development Jump to: navigation, search Name: Iowa Department of Economic Development Place: Des Moines, Iowa Zip: 50309 Product: Iowa economic development...

  20. CMI Course Inventory: Mineral Economics and Business | Critical...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mineral Economics and Business Mineral Economics and Business Of the six CMI Team members that are educational institutions, two offer courses in Mineral Economics and Business. ...

  1. Dual Integrated Appliances as an Energy and Safety Solution for Low Income

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Weatherization Webinar | Department of Energy Dual Integrated Appliances as an Energy and Safety Solution for Low Income Weatherization Webinar Dual Integrated Appliances as an Energy and Safety Solution for Low Income Weatherization Webinar Slides from the Building America webinar presented by the NorthernSTAR team. webinar_northernstar_dual_appliances_20111019.pdf (9.61 MB) More Documents & Publications Building America Expert Meeting: Recommendations for Applying Water Heaters in

  2. NREL and CSEM Jointly Set New Efficiency Record with Dual-Junction...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL and CSEM Jointly Set New Efficiency Record with Dual-Junction Solar Cell January 5, 2016 Scientists at the Energy Department's National Renewable Energy Laboratory (NREL) and ...

  3. The Power of Integrators, Financiers, and Insurers to Reduce Proliferation Risks: Nuclear Dual-Use Goods

    SciTech Connect (OSTI)

    Weise, Rachel A.; Hund, Gretchen

    2015-05-01

    Globalization of manufacturing supply chains has changed the nature of nuclear proliferation. Before 1991, nonproliferation efforts focused almost exclusively on limiting the spread of materials and equipment specifically designed for nuclear use -- reactors, centrifuges, and fissile material. Dual-use items, those items with both nuclear and non-nuclear applications, were not closely scrutinized or controlled. However, in 1991 the international community discovered that Iraq had developed a fairly sophisticated nuclear weapons program by importing dual-use items; this discovery spurred the international community to increase controls on dual-use technologies. Despite these international efforts, dual-use items are still a challenge for those seeking to limit proliferation.

  4. Dual Exchange in PCN-333: A Facile Strategy to Chemically Robust...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Dual Exchange in PCN-333: A Facile Strategy to Chemically Robust Mesoporous Chromium Metal-Organic Framework with Functional Groups Previous Next List Park, Jihye; Feng, Dawei; ...

  5. NREL and CSEM Jointly Set New Efficiency Record with Dual-Junction...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL and CSEM Jointly Set New Efficiency Record with Dual-Junction Solar Cell January 5, 2016 Scientists at the Energy Department's National Renewable Energy Laboratory (NREL) and...

  6. POLICY GUIDANCE MEMORANDUM #11A Approval Process for Dual Compensation Waivers for Reemployed Annuitants

    Broader source: Energy.gov [DOE]

    Process to  grant dual compensation (salary-offset) waivers to reemployed annuitants who work on a limited basis without reduction to their retirement annuity.

  7. Economic and policy implications of pandemic influenza.

    SciTech Connect (OSTI)

    Smith, Braeton J.; Starks, Shirley J.; Loose, Verne W.; Brown, Theresa Jean; Warren, Drake E.; Vargas, Vanessa N.

    2010-03-01

    Pandemic influenza has become a serious global health concern; in response, governments around the world have allocated increasing funds to containment of public health threats from this disease. Pandemic influenza is also recognized to have serious economic implications, causing illness and absence that reduces worker productivity and economic output and, through mortality, robs nations of their most valuable assets - human resources. This paper reports two studies that investigate both the short- and long-term economic implications of a pandemic flu outbreak. Policy makers can use the growing number of economic impact estimates to decide how much to spend to combat the pandemic influenza outbreaks. Experts recognize that pandemic influenza has serious global economic implications. The illness causes absenteeism, reduced worker productivity, and therefore reduced economic output. This, combined with the associated mortality rate, robs nations of valuable human resources. Policy makers can use economic impact estimates to decide how much to spend to combat the pandemic influenza outbreaks. In this paper economists examine two studies which investigate both the short- and long-term economic implications of a pandemic influenza outbreak. Resulting policy implications are also discussed. The research uses the Regional Economic Modeling, Inc. (REMI) Policy Insight + Model. This model provides a dynamic, regional, North America Industrial Classification System (NAICS) industry-structured framework for forecasting. It is supported by a population dynamics model that is well-adapted to investigating macro-economic implications of pandemic influenza, including possible demand side effects. The studies reported in this paper exercise all of these capabilities.

  8. Low enthalpy convective system in Western Ohio

    SciTech Connect (OSTI)

    Cannon, M.S.; Tabet, C.A.; Eckstein, Y.

    1980-01-01

    A distinct positive anomaly in the temperatures of the shallow (Pleistocene) aquifers along the Cincinnati-Findlay Arch in Western Ohio coincides with a low geothermal gradient. A conceptual model of convective currents associated with a tensional fault and/or fracture system along the crest of the Arch is suggested as an explanation of the anomaly. Hydrochemical information indicates that various quantities of warmer ground water, with the composition characteristics of deep bedrock aquifers, is present as an admixture in the shallow aquifers. This confirms the conceptual model of convection in fractures.

  9. Enthalpy restoration in geothermal energy processing system

    DOE Patents [OSTI]

    Matthews, Hugh B.

    1983-01-01

    A geothermal deep well energy extraction system is provided of the general type in which solute-bearing hot water is pumped to the earth's surface from a relatively low temperature geothermal source by transferring thermal energy from the hot water to a working fluid for driving a primary turbine-motor and a primary electrical generator at the earth's surface. The superheated expanded exhaust from the primary turbine motor is conducted to a bubble tank where it bubbles through a layer of sub-cooled working fluid that has been condensed. The superheat and latent heat from the expanded exhaust of the turbine transfers thermal energy to the sub-cooled condensate. The desuperheated exhaust is then conducted to the condenser where it is condensed and sub-cooled, whereupon it is conducted back to the bubble tank via a barometric storage tank. The novel condensing process of this invention makes it possible to exploit geothermal sources which might otherwise be non-exploitable.

  10. Exclusive J/{psi} electroproduction in a dual model

    SciTech Connect (OSTI)

    Fiore, R.; Jenkovszky, L. L.; Magas, V. K.; Melis, S.; Prokudin, A.

    2009-12-01

    Exclusive J/{psi} electroproduction is studied in the framework of the analytic S-matrix theory. The differential and integrated elastic cross sections are calculated using the modified dual amplitude with Mandelstam analyticity model. The model is applied to the description of the available experimental data and proves to be valid in a wide region of the kinematical variables s, t, and Q{sup 2}. Our amplitude can be used also as a universal background parametrization for the extraction of tiny resonance signals.

  11. Gauge theories on hyperbolic spaces and dual wormhole instabilities

    SciTech Connect (OSTI)

    Buchel, Alex

    2004-09-15

    We study supergravity duals of strongly coupled four-dimensional gauge theories formulated on compact quotients of hyperbolic spaces. The resulting background geometries are represented by Euclidean wormholes, which complicate establishing the precise gauge theory/string theory correspondence dictionary. These backgrounds suffer from the nonperturbative instabilities arising from the D3D3-bar pair-production in the background four-form potential. We discuss conditions for suppressing this Schwingerlike instability. We find that Euclidean wormholes arising in this construction develop a naked singularity before they can be stabilized.

  12. Dual-circuit, multiple-effect refrigeration system and method

    DOE Patents [OSTI]

    DeVault, Robert C.

    1995-01-01

    A dual circuit absorption refrigeration system comprising a high temperature single-effect refrigeration loop and a lower temperature double-effect refrigeration loop separate from one another and provided with a double-condenser coupling therebetween. The high temperature condenser of the single-effect refrigeration loop is double coupled to both of the generators in the double-effect refrigeration loop to improve internal heat recovery and a heat and mass transfer additive such as 2-ethyl-1-hexanol is used in the lower temperature double-effect refrigeration loop to improve the performance of the absorber in the double-effect refrigeration loop.

  13. Dual Axis Radiographic Hydrodynamic Test Facility | National Nuclear

    National Nuclear Security Administration (NNSA)

    Security Administration | (NNSA) Dual Axis Radiographic Hydrodynamic Test Facility An integral part of the national hydrotest program, the DARHT is the world's most powerful x-ray machine. DARHT consists of two electron accelerators oriented at right angles to one another. Each accelerator creates a powerful electron beam that is focused onto a metal target which converts the kinetic energy of the electron beam into high energy x or gamma-rays. The x-ray dose from one DARHT accelerator is

  14. Dual-wavelength InP quantum dot lasers

    SciTech Connect (OSTI)

    Shutts, S.; Smowton, P. M.; Krysa, A. B.

    2014-06-16

    We have demonstrated a two-section dual-wavelength diode laser incorporating distributed Bragg reflectors, with a peak-wavelength separation of 62.5?nm at 300?K. Each lasing wavelength has a different temperature dependence, providing a difference-tuning of 0.11?nm/K. We discuss the mechanisms governing the light output of the two competing modes and explain how the short wavelength can be relatively insensitive to output changes at the longer wavelength. Starting from an initial condition when the output at both wavelengths are equal, a 500% increase in the long wavelength output causes the short wavelength output to fall by only 6%.

  15. Dual-frequency glow discharges in atmospheric helium

    SciTech Connect (OSTI)

    Huang, Xiaojiang; Guo, Ying; Dai, Lu; Zhang, Jing; Shi, J. J.

    2015-10-15

    In this paper, the dual-frequency (DF) glow discharges in atmospheric helium were experimented by electrical and optical measurements in terms of current voltage characteristics and optical emission intensity. It is shown that the waveforms of applied voltages or discharge currents are the results of low frequency (LF) waveforms added to high frequency (HF) waveforms. The HF mainly influences discharge currents, and the LF mainly influences applied voltages. The gas temperatures of DF discharges are mainly affected by HF power rather than LF power.

  16. Sandia National Laboratories: News: Economic Impact

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Economic Impact Sandia National Laboratories has a robust and widespread economic impact. Spending by the Labs exceeds $2 billion a year. Nearly $1 billion goes to the procurement of goods and services nationally. Much of the remainder is spent on salaries. Explore the links below to learn more about the specific ways Sandia is making a difference at our headquarters in New Mexico and our second principal laboratory in California. New Mexico Economic Impact 2015 Download (PDF 10 MB) 2014

  17. Community Economic Analysis Guide | Open Energy Information

    Open Energy Info (EERE)

    Economic Analysis How-to manual AgencyCompany Organization: R. Hustedde, R. Shaffer, G. Pulver Phase: Create a Vision, Determine Baseline User Interface: Website Website:...

  18. "Conflict Between Economic Growth and Environmental Protection...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9, 2012, 4:15pm Colloquia MBG Auditorium "Conflict Between Economic Growth and Environmental Protection", Dr. Bryan Czech, resident, Center for the Advancement of the Steady State...

  19. CAIED Tribal Economic Development Outlook Conference

    Broader source: Energy.gov [DOE]

    How will the tribal economy do this year? What will impact your bottom line? What does the tribal economic future look like?

  20. Microsoft Word - Smart Grid Economic Impact Report

    Broader source: Energy.gov (indexed) [DOE]

    ... economic impacts on all local industries due to consumers' consumption expenditures arising from the new household incomes that are generated by the direct and indirect effects ...

  1. Reservation Economic Summit: Nevada | Department of Energy

    Office of Environmental Management (EM)

    over the phases of the project. Download the RES 2012 presentation. Addthis Related Articles Reservation Economic Summit: Nevada Indian Energy & Energy Infrastructure to be...

  2. Economic Dispatch of Electric Generation Capacity | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Dispatch of Electric Generation Capacity More Documents & Publications THE VALUE OF ECONOMIC DISPATCH A REPORT TO CONGRESS PURSUANT TO SECTION 1234 OF THE ENERGY POLICY ACT OF 2005 ...

  3. International Economic Platform for Renewable Energies IWR |...

    Open Energy Info (EERE)

    Platform for Renewable Energies IWR Jump to: navigation, search Name: International Economic Platform for Renewable Energies (IWR) Place: Mnster, Germany Zip: 48159 Sector:...

  4. Assessing the Economic Potential of Advanced Biofuels

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the Economic Potential of Advanced Biofuels - Sandia Energy Energy Search Icon Sandia Home ... Transportation Energy Co-Evolution of Biofuels Lignocellulosic Biomass Microalgae ...

  5. Algal Biofuels Techno-Economic Analysis

    Broader source: Energy.gov (indexed) [DOE]

    Algal Biofuels Techno-Economic Analysis Algae Platform Review March 24, 2015 Alexandria, ... viability, eventual adoption of algal biofuelsproducts into U.S. market 2 NATIONAL ...

  6. Technical Demonstration and Economic Validation of Geothermal...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    OilGas Wells in Texas Technical Demonstration and Economic Validation of Geothermal-Produced Electricity from Coproduced Water at Existing OilGas Wells in Texas Technical ...

  7. CAIED Tribal Economic Development Outlook Conference

    Broader source: Energy.gov [DOE]

    The Center for American Indian Economic Development (CAIED) is hosting a conference on the impact that business and the economy will have on the next year for Tribes.

  8. Photovoltaics Economic Calculator (United States) | Open Energy...

    Open Energy Info (EERE)

    (United States) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Photovoltaics Economic Calculator (United States) Focus Area: Solar Topics: System & Application...

  9. Does SEGUE/SDSS indicate a dual galactic halo?

    SciTech Connect (OSTI)

    Schönrich, Ralph; Asplund, Martin; Casagrande, Luca

    2014-05-01

    We re-examine recent claims of observational evidence for a dual Galactic halo in SEGUE/SDSS data, and trace them back to improper error treatment and neglect of selection effects. In particular, the detection of a vertical abundance gradient in the halo can be explained as a metallicity bias in distance. A similar bias and the impact of disk contamination affect the sample of blue horizontal branch stars. These examples highlight why non-volume complete samples require forward modeling from theoretical models or extensive bias-corrections. We also show how observational uncertainties produce the specific non-Gaussianity in the observed azimuthal velocity distribution of halo stars, which can be erroneously identified as two Gaussian components. A single kinematic component yields an excellent fit to the observed data, when we model the measurement process including distance uncertainties. Furthermore, we show that sample differences in proper motion space are the direct consequence of kinematic cuts and are enhanced when distance estimates are less accurate. Thus, their presence is neither proof of a separate population nor a measure of reliability for the applied distances. We conclude that currently there is no evidence from SEGUE/SDSS that would favor a dual Galactic halo over a single halo that is full of substructure.

  10. Job and Economic Development Impact (JEDI) Model: A User-Friendly Tool to Calculate Economic Impacts from Wind Projects

    SciTech Connect (OSTI)

    None

    2009-02-26

    Brochure on the Jobs and Economic Development Impact (JEDI) Model for calculating the economic impacts of wind development.

  11. The ArvinMeritor Dual Mode Hybrid Powertrain (DMHP): Opportunities and

    Broader source: Energy.gov (indexed) [DOE]

    Potential for Systems Optimization | Department of Energy 2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation vss062_smith_2011_p.pdf (685.41 KB) More Documents & Publications Vehicle Systems Integration (VSI) Research Laboratory at ORNL The Meritor Dual Mode Hybrid Powertrain CRADA The Meritor Dual Mode Hybrid Powertrain CRADA

  12. Development of a multi-resource alternate energy facility (addition of dual-fuel). Final technical report

    SciTech Connect (OSTI)

    Keel, J.S.

    1982-11-03

    This report describes the use of compressed natural gas (methane) in a dual fuel 1979 Jeep pick-up truck. Descriptions of the compressor and the dual-fuel conversion equipment are attached. (DMC)

  13. Jobs and Economic Development Impacts (Postcard)

    SciTech Connect (OSTI)

    Not Available

    2011-08-01

    The U.S. Department of Energy's Wind Powering America initiative provides information on the Jobs and Economic Development Benefits model. This postcard is a marketing piece that stakeholders can provide to interested parties; it will guide them to the Jobs and Economic Development Benefits model section on the Wind Powering America website.

  14. Catalyst rejuvenation technology and economics

    SciTech Connect (OSTI)

    Duddy, J.E.; Hildebrandt, S.J.; Koseoglu, R.O.

    1995-12-31

    One of the major factors in the economics of residue hydroprocessing is the cost of catalyst. Catalyst replacement cost in Hydrocarbon Research, Inc.`s (HRI) H-Oil{reg_sign} Process is set by a number of factors, including the feedrate, processing objectives, and feedstock type. At a given level of process performance, the catalyst replacement rate is primarily set by the rate of catalyst deactivation resulting from contaminant metals in the feedstock depositing on the catalyst surface. This is especially true as the metals content of the feedstock increases. In the recent years, interest in processing high metals feedstock has increased. For example, HRI has recently designed a new H-Oil{reg_sign} Process unit for PEMEX in Mexico, where the metals content of the design feedstock is in excess of 700 wppm. Regeneration of used hydroprocessing catalysts, through controlled oxidation of the coke deposited on the catalyst, is a common practice in the refining industry. Activity can be restored to almost fresh catalyst activity level when the primary contaminant is coke. If there is a significant amount of metal contaminants on the catalyst, regeneration alone is not effective in restoring catalyst activity. Oxidation is unable to remove contaminant metals. HRI has developed and patented a washing procedure to remove the contaminant metals. A dilute acid wash (to remove metals), in conjunction with conventional regeneration (to remove coke), can restore high levels of catalyst activity of spent catalysts with high levels of metal contaminants. The combination of acid washing and controlled oxidation forms the basis of HRI`s Catalyst Rejuvenation Technology.

  15. Economic growth, carrying capacity, and the environment

    SciTech Connect (OSTI)

    Arrow, K.; Bolin, B.; Costanza, R.; Dasgupta, P.; Folke, C.; Maeler, K.G.; Holling, C.S.; Jansson, B.O.; Levin, S.; Perrings, C.

    1995-04-28

    National and international economic policy has usually ignored the environment. In areas where the environment is beginning to impinge on policy, as in the General Agreement on Tariffs and Trade (GATT) and the North American Free Trade Agreement (NAFTA), it remains a tangential concern, and the presumption is often made that economic growth and economic liberalization (including the liberalization of international trade) are, in some sense, good for the environment. This notion has meant that economy-wide policy reforms designed to promote growth and liberalization have been encouraged with little regard to their environmental consequences, presumably on the assumption that these consequences would either take care of themselves or could be dealt with separately. In this article, we discuss the relation between economic growth and environmental quality, and the link between economic activity and the carrying capacity and resilience of the environment.

  16. Oil and economic performance in industrial countries

    SciTech Connect (OSTI)

    Nordhaus, W.D.

    1980-01-01

    The Organization for Economic Co-operation and Development (OECD) countries have experienced slower economic growth and periods of discontinuity in the energy market since the 1973-74 oil embargo. A review of this phenomenon examines changes in the market during the 1960s and 70s, linkages between oil prices and economic performance, and appropriate policy responses. When price elasticities are calculated over time, recent US economic behavior appears to have both historical and cross-sountry consistency. Little flexibility is seen in the available energy-using technologies for producing goods and services, while energy-using capital has been sluggish. Dr. Nordhaus advocates high oil price and high tax policies as the best way to limit demand without slowing economic growth. (DCK)

  17. Economic Impact Analysis for EGS | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Economic Impact Analysis for EGS Economic Impact Analysis for EGS Project objective: To conduct an economic impact study for EGS and to develop a Geothermal Economics Calculator (GEC) tool to quantify (in economic terms) the potential job, energy and environmental impacts associated with electric power production from geothermal resources. analysis_levey_economic_impact_analysis.pdf (456.77 KB) More Documents & Publications Economic Impact Analysis for EGS U.S. DOE Geothermal Electricity

  18. Dual annular rotating "windowed" nuclear reflector reactor control system

    DOE Patents [OSTI]

    Jacox, Michael G.; Drexler, Robert L.; Hunt, Robert N. M.; Lake, James A.

    1994-01-01

    A nuclear reactor control system is provided in a nuclear reactor having a core operating in the fast neutron energy spectrum where criticality control is achieved by neutron leakage. The control system includes dual annular, rotatable reflector rings. There are two reflector rings: an inner reflector ring and an outer reflector ring. The reflectors are concentrically assembled, surround the reactor core, and each reflector ring includes a plurality of openings. The openings in each ring are capable of being aligned or non-aligned with each other. Independent driving means for each of the annular reflector rings is provided so that reactor criticality can be initiated and controlled by rotation of either reflector ring such that the extent of alignment of the openings in each ring controls the reflection of neutrons from the core.

  19. DARHT status and preparations for dual-axis hydrotesting (u)

    SciTech Connect (OSTI)

    Bowman, David W

    2010-01-01

    The status of the DARHT facility, including a history of events that have taken place since the end of the DARHT Second Axis Refurbishment Project, is discussed. Technical and operational enhancements that have been made will be addressed, and recent technical challenges, such as the RF noise in the kicker region, are discussed. Historical data on reliability of the second axis is discussed, as well as operational changes made to enhance reliability. In addition, the path forward for integrating the second axis into overall DARHT operations in preparation for a hydrotest is addressed. Timing integration tests are accompanied by a series of tests to evaluate neutron contamination and cross-axis scatter, with attempts being made to provide adequate shielding to minimize the effects of neutrons and cross-beam scatter. The discussion includes results of the testing performed to-date, and concludes with a discussion of the path forward for dual-axis hydrotesting at DARHT.

  20. Parameterized reduced-order models using hyper-dual numbers.

    SciTech Connect (OSTI)

    Fike, Jeffrey A.; Brake, Matthew Robert

    2013-10-01

    The goal of most computational simulations is to accurately predict the behavior of a real, physical system. Accurate predictions often require very computationally expensive analyses and so reduced order models (ROMs) are commonly used. ROMs aim to reduce the computational cost of the simulations while still providing accurate results by including all of the salient physics of the real system in the ROM. However, real, physical systems often deviate from the idealized models used in simulations due to variations in manufacturing or other factors. One approach to this issue is to create a parameterized model in order to characterize the effect of perturbations from the nominal model on the behavior of the system. This report presents a methodology for developing parameterized ROMs, which is based on Craig-Bampton component mode synthesis and the use of hyper-dual numbers to calculate the derivatives necessary for the parameterization.

  1. Dual manifold system and method for fluid transfer

    DOE Patents [OSTI]

    Doktycz, Mitchel J.; Bryan, William Louis; Kress, Reid

    2003-05-27

    A dual-manifold assembly is provided for the rapid, parallel transfer of liquid reagents from a microtiter plate to a solid state microelectronic device having biological sensors integrated thereon. The assembly includes aspiration and dispense manifolds connected by a plurality of conduits. In operation, the aspiration manifold is actuated such that the aspiration manifold is seated onto an array of reagent-filled wells of the microtiter plate. The wells are pressurized to force reagent through conduits toward the dispense manifold. A pressure pulse provided by a standard ink-jet printhead ejects nanoliter-to-picoliter droplets of reagent through an array of printhead orifices and onto test sites on the surface of the microelectronic device.

  2. Dual manifold system and method for fluid transfer

    DOE Patents [OSTI]

    Doktycz, Mitchel J.; Bryan, William Louis; Kress, Reid

    2003-09-30

    A dual-manifold assembly is provided for the rapid, parallel transfer of liquid reagents from a microtiter plate to a solid state microelectronic device having biological sensors integrated thereon. The assembly includes aspiration and dispense manifolds connected by a plurality of conduits. In operation, the aspiration manifold is actuated such that the aspiration manifold is seated onto an array of reagent-filled wells of the microtiter plate. The wells are pressurized to force reagent through conduits toward the dispense manifold. A pressure pulse provided by a standard ink-jet printhead ejects nanoliter-to-picoliter droplets of reagent through an array of printhead orifices and onto test sites on the surface of the microelectronic device.

  3. Investigation of plasma diagnostics using a dual frequency harmonic technique

    SciTech Connect (OSTI)

    Kim, Dong-Hwan; Kim, Young-Do; Cho, Sung-Won; Kim, Yu-Sin; Chung, Chin-Wook

    2014-09-07

    Plasma diagnostic methods using harmonic currents analysis of electrostatic probes were experimentally investigated to understand the differences in their measurement of the plasma parameters. When dual frequency voltage (ω{sub 1},ω{sub 2}) was applied to a probe, various harmonic currents (ω{sub 1}, 2ω{sub 1},ω{sub 2}, 2ω{sub 2},ω{sub 2}±ω{sub 1},ω{sub 2}±2ω{sub 1}) were generated due to the non-linearity of the probe sheath. The electron temperature can be obtained from the ratio of the two harmonics of the probe currents. According to the combinations of the two harmonics, the sensitivities in the measurement of the electron temperature differed, and this results in a difference of the electron temperature. From experiments and simulation, it is shown that this difference is caused by the systematic and random noise.

  4. Representing ductile damage with the dual domain material point method

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Long, C. C.; Zhang, D. Z.; Bronkhorst, C. A.; Gray, III, G. T.

    2015-12-14

    In this study, we incorporate a ductile damage material model into a computational framework based on the Dual Domain Material Point (DDMP) method. As an example, simulations of a flyer plate experiment involving ductile void growth and material failure are performed. The results are compared with experiments performed on high purity tantalum. We also compare the numerical results obtained from the DDMP method with those obtained from the traditional Material Point Method (MPM). Effects of an overstress model, artificial viscosity, and physical viscosity are investigated. Our results show that a physical bulk viscosity and overstress model are important in thismore » impact and failure problem, while physical shear viscosity and artificial shock viscosity have negligible effects. A simple numerical procedure with guaranteed convergence is introduced to solve for the equilibrium plastic state from the ductile damage model.« less

  5. Representing ductile damage with the dual domain material point method

    SciTech Connect (OSTI)

    Long, C. C.; Zhang, D. Z.; Bronkhorst, C. A.; Gray, III, G. T.

    2015-12-14

    In this study, we incorporate a ductile damage material model into a computational framework based on the Dual Domain Material Point (DDMP) method. As an example, simulations of a flyer plate experiment involving ductile void growth and material failure are performed. The results are compared with experiments performed on high purity tantalum. We also compare the numerical results obtained from the DDMP method with those obtained from the traditional Material Point Method (MPM). Effects of an overstress model, artificial viscosity, and physical viscosity are investigated. Our results show that a physical bulk viscosity and overstress model are important in this impact and failure problem, while physical shear viscosity and artificial shock viscosity have negligible effects. A simple numerical procedure with guaranteed convergence is introduced to solve for the equilibrium plastic state from the ductile damage model.

  6. Iterative Self-Dual Reconstruction on Radar Image Recovery

    SciTech Connect (OSTI)

    Martins, Charles; Medeiros, Fatima; Ushizima, Daniela; Bezerra, Francisco; Marques, Regis; Mascarenhas, Nelson

    2010-05-21

    Imaging systems as ultrasound, sonar, laser and synthetic aperture radar (SAR) are subjected to speckle noise during image acquisition. Before analyzing these images, it is often necessary to remove the speckle noise using filters. We combine properties of two mathematical morphology filters with speckle statistics to propose a signal-dependent noise filter to multiplicative noise. We describe a multiscale scheme that preserves sharp edges while it smooths homogeneous areas, by combining local statistics with two mathematical morphology filters: the alternating sequential and the self-dual reconstruction algorithms. The experimental results show that the proposed approach is less sensitive to varying window sizes when applied to simulated and real SAR images in comparison with standard filters.

  7. Slowly Varying Dilaton Cosmologies and Their Field Theory Duals

    SciTech Connect (OSTI)

    Awad, Adel; Das, Sumit R.; Ghosh, Archisman; Oh, Jae-Hyuk; Trivedi, Sandip P.; /Tata Inst. /Stanford U., ITP /SLAC

    2011-06-28

    We consider a deformation of the AdS{sub 5} x S{sup 5} solution of IIB supergravity obtained by taking the boundary value of the dilaton to be time dependent. The time dependence is taken to be slowly varying on the AdS scale thereby introducing a small parameter {epsilon}. The boundary dilaton has a profile which asymptotes to a constant in the far past and future and attains a minimum value at intermediate times. We construct the sugra solution to first non-trivial order in {epsilon}, and find that it is smooth, horizon free, and asymptotically AdS{sub 5} x S{sup 5} in the far future. When the intermediate values of the dilaton becomes small enough the curvature becomes of order the string scale and the sugra approximation breaks down. The resulting dynamics is analysed in the dual SU(N) gauge theory on S{sup 3} with a time dependent coupling constant which varies slowly. When N{epsilon} << 1, we find that a quantum adiabatic approximation is applicable, and use it to argue that at late times the geometry becomes smooth AdS{sub 5} x S{sup 5} again. When N{epsilon} >> 1, we formulate a classical adiabatic perturbation theory based on coherent states which arises in the large N limit. For large values of the tHooft coupling this reproduces the supergravity results. For small 'tHooft coupling the coherent state calculations become involved and we cannot reach a definite conclusion. We argue that the final state should have a dual description which is mostly smooth AdS5 space with the possible presence of a small black hole.

  8. HTGR Application Economic Model Users' Manual

    SciTech Connect (OSTI)

    A.M. Gandrik

    2012-01-01

    The High Temperature Gas-Cooled Reactor (HTGR) Application Economic Model was developed at the Idaho National Laboratory for the Next Generation Nuclear Plant Project. The HTGR Application Economic Model calculates either the required selling price of power and/or heat for a given internal rate of return (IRR) or the IRR for power and/or heat being sold at the market price. The user can generate these economic results for a range of reactor outlet temperatures; with and without power cycles, including either a Brayton or Rankine cycle; for the demonstration plant, first of a kind, or nth of a kind project phases; for up to 16 reactor modules; and for module ratings of 200, 350, or 600 MWt. This users manual contains the mathematical models and operating instructions for the HTGR Application Economic Model. Instructions, screenshots, and examples are provided to guide the user through the HTGR Application Economic Model. This model was designed for users who are familiar with the HTGR design and Excel and engineering economics. Modification of the HTGR Application Economic Model should only be performed by users familiar with the HTGR and its applications, Excel, and Visual Basic.

  9. Petrographic characterization of economizer fly ash

    SciTech Connect (OSTI)

    Valentim, B.; Hower, J.C.; Soares, S.; Guedes, A.; Garcia, C.; Flores, D.; Oliveira, A.

    2009-11-15

    Policies for reducing NOx emissions have led power plants to restrict O{sub 2}, resulting in high-carbon fly ash production. Therefore, some potentially useful fly ash, such as the economizer fly ash, is discarded without a thorough knowledge of its composition. In order to characterize this type of fly ash, samples were collected from the economizer Portuguese power plant burning two low-sulfur bituminous coals. Characterization was also performed on economizer fly ash subsamples after wet sieving, density and magnetic separation. Analysis included atomic absorption spectroscopy, loss-on-ignition, scanning electron microscopy/energy-dispersive X-ray spectroscopy, optical microscopy, and micro-Raman spectroscopy.

  10. Appendix B: High Economic Growth case projections

    Gasoline and Diesel Fuel Update (EIA)

    B High Economic Growth case projections This page inTenTionally lefT blank 43 U.S. Energy Information Administration | International Energy Outlook 2016 High Economic Growth case projections Table B1. World total primary energy consumption by region, High Economic Growth case, 2011-40 (quadrillion Btu) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 120.6 118.1 128.2 132.3 137.0 142.4 150.1 0.9 United States a 96.8 94.4